Glass ceramics for incinerator ash immobilization

NASA Astrophysics Data System (ADS)

Malinina, G. A.; Stefanovsky, O. I.; Stefanovsky, S. V.

2011-09-01

Calcined solid radioactive waste (incinerator slag) surrogate and either Na 2Si 2O 5 or Na 2B 4O 7 (borax) at various mass ratios were melted in silicon carbide crucibles in a resistive furnace at temperatures of up to 1775 K (slag without additives). Portions of the melts were poured onto a metal plate; the residues were slowly cooled in turned-off furnace. Both quenched and slowly cooled materials were composed of the same phases. At high slag contents in silicate-based materials nepheline and britholite were found to be major phases. Britholite formed at higher slag content (85 wt.%) became major phase in the vitrified slag. In the system with borax at low slag contents (25 and 50 wt.%) material are composed of predominant vitreous and minor calcium silicate larnite type phase Ca 2SiO 4 where Ca 2+ ions are replaced by different cations. The materials containing slag in amount of 75 wt.% and more are chemically durable. The changes in the structure of anionic motif of quenched samples depending on slag loading were studied by IR spectroscopy.

Maximum heat of mass concrete - phase 2 [summary].

DOT National Transportation Integrated Search

2016-12-01

Concrete hardens through a chemical reaction that produces heat and expansion, followed by contraction as the concrete cools. Concrete near the edge of a pour cools faster and shrinks earlier than concrete further from the edge. Most concrete pours a...

Etude des interdiffusions en phase solide dans le contact Er/GaAs

NASA Astrophysics Data System (ADS)

Députier, S.; Guivarc'h, A.; Caulet, J.; Minier, M.; Guérin, R.

1994-05-01

Solid state interdiffusions between a thin film of erbium deposited under vacuum conditions and (001) and (111) GaAs substrates were investigated in the temperature range 350-800 ^{circ}C. Complementary analysis methods (RBS, X-ray diffraction) allow us to point out, according to annealing temperatures, successives steps of the interaction corresponding to different mixtures of phases, essentially binaries. These steps are strongly depending on the GaAs substrate orientation, especially the final step of the interdiffusions. On (001) GaAs, only two steps have been observed : no visible interaction is noticed between erbium and GaAs before 600 ^{circ}C ; the interaction begins at 600 ^{circ}C, evolves slightly and leads at 800 ^{circ}C to the nominal composition " Er{10}GaAs " which corresponds to a mixture of several phases Er5Ga3, Er and ErAs. On (111) GaAs, several steps of interaction have been found ; first of all, erbium reacts with the substrate at 400 ^{circ}C (Er5Ga3 + Er mixture), then the reaction is continuing at 600 ^{circ}C (Er5Ga3 + Er + ErAs mixture) before reaching at 800 ^{circ}C the nominal composition " Er{1,5}GaAs ", which is in fact a mixture of the three binaries ErAs + ErGa2 + Er3Ga5. It can be noticed that the 800 ^{circ}C annealing is not sufficient to reach the mixture of the phases ErAs + Ga which, according to the ternary phase diagram, should be the final stage of the interaction Er/GaAs. The analysis of the Er/GaAs interdiffusions shows that ErAs is the " key " compound around which the interaction progresses. This compound appears as an ideal candidate to realize epitaxial ErAs/GaAs heterostructures. Les interdiffusions en phase solide entre une couche mince d'erbium déposée dans des conditions d'ultra-vide et des substrats de GaAs orientés (001) et (111) ont été étudiées après des traitements thermiques d'une heure entre 350 et 800 ^{circ}C. L'utilisation de techniques complémentaires d'analyse (RBS, diffraction X) a permis de mettre en évidence, en fonction de la température de recuit, plusieurs étapes successives d'interaction correspondant à des mélanges de phases, essentiellement des binaires. Elles dépendent fortement de l'orientation du substrat de GaAs, en particulier l'étape finale des interactions. Sur GaAs (001), seules deux étapes ont été observées : avant 600 ^{circ}C, il n'y a pas d'interaction visible de l'erbium avec le substrat ; celle-ci ne s'amorce qu'à 600 ^{circ}C pour n'évoluer ensuite que faiblement et conduire, à 800 ^{circ}C, à une composition nominale " Er{10}GaAs ", mélange des phases Er5Ga3 + Er + ErAs. Sur GaAs (111), plusieurs étapes d'interaction sont observées : l'erbium réagit avec le substrat dès 400 ^{circ}C (mélange des phases Er5Ga3 + Er), puis l'interaction se poursuit à 600 ^{circ}C (mélange Er5Ga3 + Er + ErAs) avant d'atteindre à 800 ^{circ}C la composition nominale " Er{1,5}GaAs ", constituée d'un mélange de grains des trois binaires ErAs + ErGa2 + Er3Ga5. Il faut noter que le recuit à 800 ^{circ}C n'est pas suffisant pour atteindre le mélange de phases Ga + ErAs qui, selon le diagramme ternaire, devrait être le stade ultime de l'interaction Er/GaAs. L'analyse des interdiffusions Er/GaAs montre que ErAs est le composé " clé " autour duquel pivote l'interaction Er/GaAs. Ce composé apparaît comme un candidat idéal pour la réalisation d'hétérostructures épitaxiées ErAs/GaAs.

High temperature thermal energy storage, including a discussion of TES integrated into power plants

NASA Technical Reports Server (NTRS)

Turner, R. H.

1978-01-01

Storage temperatures of 260 C and above are considered. Basic considerations concerning energy thermal storage are discussed, taking into account general aspects of thermal energy storage, thermal energy storage integrated into power plants, thermal storage techniques and technical considerations, and economic considerations. A description of system concepts is provided, giving attention to a survey of proposed concepts, storage in unpressurized fluids, water storage in pressurized containers, the use of an underground lined cavern for water storage, a submerged thin insulated steel shell under the ocean containing pressurized water, gas passage through solid blocks, a rock bed with liquid heat transport fluid, hollow steel ingots, heat storage in concrete or sand, sand in a fluidized bed, sand poured over pipes, a thermal energy storage heat exchanger, pipes or spheres filled with phase change materials (PCM), macroencapsulated PCM with heat pipe concept for transport fluid, solid PCM removed from heat transfer pipes by moving scrapers, and the direct contact between PCM and transport fluid.

Techniques d'inspection par ondes guidees ultrasonores d'assemblages brases dans des reacteurs aeronautiques =

NASA Astrophysics Data System (ADS)

Comot, Pierre

L'industrie aeronautique, cherche a etudier la possibilite d'utiliser de maniere structurelle des joints brases, dans une optique de reduction de poids et de cout. Le developpement d'une methode d'evaluation rapide, fiable et peu couteuse pour evaluer l'integrite structurelle des joints apparait donc indispensable. La resistance mecanique d'un joint brase dependant principalement de la quantite de phase fragile dans sa microstructure. Les ondes guidees ultrasonores permettent de detecter ce type de phase lorsqu'elles sont couplees a une mesure spatio-temporelle. De plus la nature de ce type d'ondes permet l'inspection de joints ayant des formes complexes. Ce memoire se concentre donc sur le developpement d'une technique basee sur l'utilisation d'ondes guidees ultrasonores pour l'inspection de joints brases a recouvrement d'Inconel 625 avec comme metal d'apport du BNi-2. Dans un premiers temps un modele elements finis du joint a ete utilise pour simuler la propagation des ultrasons et optimiser les parametres d'inspection, la simulation a permis egalement de demontrer la faisabilite de la technique pour la detection de la quantite de phase fragile dans ce type de joints. Les parametres optimises sont la forme de signal d'excitation, sa frequence centrale et la direction d'excitation. Les simulations ont montre que l'energie de l'onde ultrasonore transmise a travers le joint aussi bien que celle reflechie, toutes deux extraites des courbes de dispersion, etaient proportionnelles a la quantite de phase fragile presente dans le joint et donc cette methode permet d'identifier la presence ou non d'une phase fragile dans ce type de joint. Ensuite des experimentations ont ete menees sur trois echantillons typiques presentant differentes quantites de phase fragile dans le joint, pour obtenir ce type d'echantillons differents temps de brasage ont ete utilises (1, 60 et 180 min). Pour cela un banc d'essai automatise a ete developpe permettant d'effectuer une analyse similaire a celle utilisee en simulation. Les parametres experimentaux ayant ete choisis en accord avec l'optimisation effectuee lors des simulations et apres une premiere optimisation du procede experimental. Finalement les resultats experimentaux confirment les resultats obtenus en simulation, et demontrent le potentiel de la methode developpee.

Hazard Studies for Solid Propellant Rocket Motors (Etude des Risque pour les Moteurs-Fusees a Propergols Solides)

DTIC Science & Technology

1990-09-01

RESEARCH AND DEVELOPMENT (ORGANISATION DU TRAITE DE LATIANTIOUF NORD) AGARDograph No.3 16 Hazard Studies for Solid Propellant Rocket Motors (Etudes de...member nations to use their research and development capabilities for the common benefit of the NATO community; - Providing scientific and technical...advice and assistance to the Military Committee in the field of aerospace research and development (with particular regard to its military application

Optimisation des trajectoires verticales par la methode de la recherche de l'harmonie =

NASA Astrophysics Data System (ADS)

Ruby, Margaux

Face au rechauffement climatique, les besoins de trouver des solutions pour reduire les emissions de CO2 sont urgentes. L'optimisation des trajectoires est un des moyens pour reduire la consommation de carburant lors d'un vol. Afin de determiner la trajectoire optimale de l'avion, differents algorithmes ont ete developpes. Le but de ces algorithmes est de reduire au maximum le cout total d'un vol d'un avion qui est directement lie a la consommation de carburant et au temps de vol. Un autre parametre, nomme l'indice de cout est considere dans la definition du cout de vol. La consommation de carburant est fournie via des donnees de performances pour chaque phase de vol. Dans le cas de ce memoire, les phases d'un vol complet, soit, une phase de montee, une phase de croisiere et une phase de descente, sont etudies. Des " marches de montee " etaient definies comme des montees de 2 000ft lors de la phase de croisiere sont egalement etudiees. L'algorithme developpe lors de ce memoire est un metaheuristique, nomme la recherche de l'harmonie, qui, concilie deux types de recherches : la recherche locale et la recherche basee sur une population. Cet algorithme se base sur l'observation des musiciens lors d'un concert, ou plus exactement sur la capacite de la musique a trouver sa meilleure harmonie, soit, en termes d'optimisation, le plus bas cout. Differentes donnees d'entrees comme le poids de l'avion, la destination, la vitesse de l'avion initiale et le nombre d'iterations doivent etre, entre autre, fournies a l'algorithme pour qu'il soit capable de determiner la solution optimale qui est definie comme : [Vitesse de montee, Altitude, Vitesse de croisiere, Vitesse de descente]. L'algorithme a ete developpe a l'aide du logiciel MATLAB et teste pour plusieurs destinations et plusieurs poids pour un seul type d'avion. Pour la validation, les resultats obtenus par cet algorithme ont ete compares dans un premier temps aux resultats obtenus suite a une recherche exhaustive qui a utilisee toutes les combinaisons possibles. Cette recherche exhaustive nous a fourni l'optimal global; ainsi, la solution de notre algorithme doit se rapprocher le plus possible de la recherche exhaustive afin de prouver qu'il donne des resultats proche de l'optimal global. Une seconde comparaison a ete effectuee entre les resultats fournis par l'algorithme et ceux du Flight Management System (FMS) qui est un systeme d'avionique situe dans le cockpit de l'avion fournissant la route a suivre afin d'optimiser la trajectoire. Le but est de prouver que l'algorithme de la recherche de l'harmonie donne de meilleurs resultats que l'algorithme implemente dans le FMS.

Cold pearl surfactant-based blends.

PubMed

Crombie, R L

1997-10-01

Pearlizing agents have been used for many years in cosmetic formulations to add a pearlescent effect. Cold pearl surfactant-based blends are mixtures of glycol stearates and surfactants which can be blended in the cold into a wide range of personal-care formulations to create a pearlescent lustre effect. Under controlled manufacturing conditions constant viscosities and crystalline characteristics can be obtained. The development of these blends has been driven by efforts to improve the economics of adding solid pearlizing agents directly into a hot mix formulation. This paper summarizes the history of pearlizers, describes their advantages and physical chemistry of the manufacturing process. Finally some suggestions for applications are given. Les agents nacrants sont utilises depuis de nombreuses annees dans les formulations cosmetiques pour ajouter un effet nacre. Les melanges a froid a base de tensioactif nacre sont des melanges de stearates de glycol et de tensioactifs qui peuvent etre melanges a froid dans une large gamme de formulations d'hygiene personnelle pour creer un effet de lustre nacre. On peut obtenir des viscosites et des proprietes cristallines constantes avec des conditions de fabrication maitrisees. Le developpement de ces melanges a ete porte par les efforts pour ameliorer les couts de l'ajout d'agents nacrants solides directement dans une formulation melangee de l'ajout d'agents nacrants solides directement dans une formulation melangee a chaud. Cet article resume l'histoire des agents nacrants, decrit leurs avantages et al physico-chimie du procede de fabrication. On emet a la fin cetaines suggestions d'applications.

Simultaneous Preconcentration and Determination of Brilliant Blue and Sunset Yellow in Foodstuffs by Solid-Phase Extraction Combined UV-Vis Spectrophotometry.

PubMed

Bişgin, Abdullah Taner

2018-05-29

Background: Brilliant Blue and Sunset Yellow, two highly water-soluble synthetic food dyes, are the most popular food dyes used and consumed. Although they are not highly toxic, some health problems can be observed when excessive amounts of food products containing these dyes are consumed. Objectives: The aim of the study was to develop a simultaneous UV-Vis combined solid-phase extraction method, based on the adsorption onto Amberlite XAD-8 resin, for determination of Brilliant Blue and Sunset Yellow dyes. Methods: Sample solution was poured into the reservoir of the column and permitted to gravitationally pass through the column at 2 mL/min flow rate. Adsorbed dyes were eluted to 5 mL of final volume with 1 mol/L HNO₃ in ethanol solution by applying a 2 mL/min flow rate. Dye concentrations of the solution were determined at 483 and 630 nm for Sunset Yellow and Brilliant Blue, respectively. Results: The detection limits of the method for Brilliant Blue and Sunset Yellow were determined as 0.13 and 0.66 ng/mL, respectively. Preconcentration factor was 80. Brilliant Blue contents of real food samples were found to be between 11 and 240 μg/g. Sunset Yellow concentrations of foodstuffs were determined to be between 19 and 331 μg/g. Conclusions: Economical, effective, and simple simultaneous determination of Brilliant Blue and Sunset Yellow was achieved by using a solid-phase extraction combined UV-Vis spectrometry method. Highlights: The method is applicable and suitable for routine analysis in quality control laboratories without the need for expert personnel and high operational costs because the instrumentation is simple and inexpensive.

Specific Adaptation of Gas Atomization Processing for Al-Based Alloy Powder for Additive Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Iver; Siemon, John

The initial three atomization attempts resulted in “freeze-outs” within the pour tubes in the pilot-scale system and yielded no powder. Re-evaluation of the alloy liquidus temperatures and melting characteristics, in collaboration with Alcoa, showed further superheat to be necessary to allow the liquid metal to flow through the pour tube to the atomization nozzle. A subsequent smaller run on the experimental atomization system verified these parameters and was successful, as were all successive runs on the larger pilot scale system. One alloy composition froze-out part way through the atomization on both pilot scale runs. SEM images showed needle formation andmore » phase segregations within the microstructure. Analysis of the pour tube freeze-out microstructures showed that large needles formed within the pour tube during the atomization experiment, which eventually blocked the melt stream. Alcoa verified the needle formation in this alloy using theoretical modeling of phase solidification. Sufficient powder of this composition was still generated to allow powder characterization and additive manufacturing trials at Alcoa.« less

A simple and specific high performance liquid chromatography method for the assay of a series of novel dermal penetration enhancers.

PubMed

Michniak, B B; Seyda, K L

1993-02-01

Synopsis A series of clofibric acid amides has been synthesized and previously reported by the authors as possessing enhancer activity in vitro in athymic nude mouse skin against model drugs, hydrocortisone-21-acetate and beta-methasone-17-valerate. An assay was required for each of these enhancers however, which would be specific for each compound and would also separate model drugs and their metabolite peaks. This study reports reverse phase high performance liquid chromatography assays for clofibric acid amide and seven derivatives (Ia-Ig). All enhancers showed maximum absorption at 232 nm, betamethasone (BM) and its valerate (BMV) at 238 nm, and hydrocortisone (HC) and its acetate (HCA) at 242 nm. Practical units of detection for the amides were 0.46-2.8 mug ml(-1) and peaks were sharp and well-separated from steroid peaks in three vehicles - methanol alone. Franz diffusion cell receptor phase samples (isotonic phosphate buffer), and full-thickness athymic nude mouse skin extracts in methanol. Mobile phases consisted of various proportions of acetonitrile and water, some with 2-propanol. The octyl amide for example, with mobile phase CH(3)CN: H(2)O (85:15) at 1 ml min(-1) had a retention time (t(R)) of 7.9 mins. Under the same conditions, retention times for the steroids were HC, t(R)= 3.3 mins; HCA, t(R)= 4.3 mins; BM, t(R)= 3.4 mins; BMV, t(R)= 4.6 mins. Résumé Les auteurs avaient démontré dans un article précédent le pouvoir accélérateur de pénétration dermique in vitro d'une gamme d'amides d'acide clofibrique sur la peau de souris sans poils, et sans thymus avec des médicaments types tels que l'acetate 21 d'hydrocortisone et le valerate 17 de beta-metasone. Il a cependant été requis, pour chacun de ces accélérateurs, un test spécifique pour chaque composition, permettant de séparer chaque médicament et les pics des métabolites. Cette étude décrit des tests par chromatographie liquide à haute performance en phase inverse pour l'acide chlofibrique et 7 dérivés (Ia-Ig). Tous les accélérateurs ont montré une absorption maximale à 232 nm, la beta-metasone (BM) et son valerate (BMV) à 238 nm, l'hydrocortisone (HC) et son acetate (HCA) à 242 nm. Les unités de détection s'élevaient à 0.46-2.8 mug ml(-1) pour les amides et les pics étaient aigus et distincts des pics stéroïdes et se composaient de 3 véhicules - le méthanol seul, des échantillons du récepteur de cellule de diffusion Franz (tampon du phosphate isotonique) et des extraits de peau de souris sans thymus dans du méthanol. Les phases mobiles étaient constituées de différentes proportions d'acetonitrile et d'eau, certaines avec du propanol-2. L'amide octyl par exemple, avec une phase mobile CH(3)CN: H(2)O (85:15) à 1 ml min(-1) avait un temps de rétention (t(R)) de 7.9 min. Dans des conditions identiques, les temps de rétention pour les stéroïdes étaient les suivants: pour HC, t(R)= 3.3 mins; pour HCA, t(R)= 4.3 mins; pour BM: t(R)= 3.4 mins; pour BMV: t(R)= 4.6 mins.

Numerical Study of Impingement Location of Liquid Jet Poured from a Tilting Ladle with Lip Spout

NASA Astrophysics Data System (ADS)

Castilla, R.; Gamez-Montero, P. J.; Raush, G.; Khamashta, M.; Codina, E.

2017-04-01

A new approach for simulating liquid poured from a tilting lip spout is presented, using neither a dynamic mesh nor the moving solid solution method. In this case only the tilting ladle is moving, so we propose to rotate the gravitational acceleration at an angular velocity prescribed by a geometrical and dynamical calculation to keep the poured flow rate constant. This angular velocity is applied to modify the orientation of the gravity vector in computational fluid dynamics (CFD) simulations using the OpenFOAM® toolbox. Also, fictitious forces are considered. The modified solver is used to calculate the impingement location for six spout geometries and compare the jet dispersion there. This method could offer an inexpensive tool to calculate optimal spout geometries to reduce sprue size in the metal casting industry.

Solutions multiples thermocapillaires en zone flottante à gravité nulle

NASA Astrophysics Data System (ADS)

Chénier, E.; Delcarte, C.; Labrosse, G.

1998-04-01

An original model is adopted to analyse the melted phase hydrodynamics, in the floating zone technique configuration for crystal growth. In particular, a small capillary scale located near the fusion fronts is taken into account. Its size turns out to influence significantly the flow structure. For the first time, multiple solutions are exhibited in zero gravity. Un modèle original a été adopté pour analyser l'hydrodynamique de la phase fondue pour la technique de la zone flottante, en croissance cristalline. En particulier, une petite échelle capillaire, située près des fronts de fusion, est prise en considération. Son extension se révèle influencer significativement la structure des écoulements. L'existence de solutions multiples est, pour la première fois, mise en évidence en gravité zéro.

Nuclear reactor containment structure with continuous ring tunnel at grade

DOEpatents

Seidensticker, Ralph W.; Knawa, Robert L.; Cerutti, Bernard C.; Snyder, Charles R.; Husen, William C.; Coyer, Robert G.

1977-01-01

A nuclear reactor containment structure which includes a reinforced concrete shell, a hemispherical top dome, a steel liner, and a reinforced-concrete base slab supporting the concrete shell is constructed with a substantial proportion thereof below grade in an excavation made in solid rock with the concrete poured in contact with the rock and also includes a continuous, hollow, reinforced-concrete ring tunnel surrounding the concrete shell with its top at grade level, with one wall integral with the reinforced concrete shell, and with at least the base of the ring tunnel poured in contact with the rock.

Submarine Structure Modeling and Analysis for Life-Cycle Management: Phase 2

DTIC Science & Technology

2008-05-01

tous les emplacements de jauges extensométriques. Un certain nombre d’autres programmes FORTRAN ont également été mis au point pour incorporer dans... jauges extensométriques. Un certain nombre d’autres programmes FORTRAN ont également été mis au point pour incorporer dans les modèles par éléments

Formulation de cas dans la psychose débutante : Quels outils pour le travail en équipe?

PubMed Central

Elowe, Julien; Mebdouhi, Nadir; Solida, Alessandra; Conus, Philippe

2017-01-01

Nous présentons d’abord brièvement le programme TIPP et les concepts généraux de la prise en charge précoce dans la psychose débutante. Un des objectifs de l’intervention dans la phase précoce des troubles psychotiques est notamment de proposer des soins spécifiques adaptés à cette phase de la maladie. En début de prise en charge, l’équipe de soins et en particulier le gestionnaire de cas (case manager), chef d’orchestre de la prise en charge, sont confrontés à une quantité importante d’information dont il faut dégager les lignes de forces pour mettre en place une prise en charge adaptée. Cet article propose un modèle qui peut constituer un outil de travail précieux pour les équipes travaillant dans l’intervention précoce pour faire émerger une formulation de cas et synthétiser les situations cliniques des patients, en extraire une histoire qui fasse sens et ainsi faciliter la mise en place d’un projet thérapeutique. PMID:28558256

Development of a CFD code for casting simulation

NASA Technical Reports Server (NTRS)

Murph, Jesse E.

1993-01-01

Because of high rejection rates for large structural castings (e.g., the Space Shuttle Main Engine Alternate Turbopump Design Program), a reliable casting simulation computer code is very desirable. This code would reduce both the development time and life cycle costs by allowing accurate modeling of the entire casting process. While this code could be used for other types of castings, the most significant reductions of time and cost would probably be realized in complex investment castings, where any reduction in the number of development castings would be of significant benefit. The casting process is conveniently divided into three distinct phases: (1) mold filling, where the melt is poured or forced into the mold cavity; (2) solidification, where the melt undergoes a phase change to the solid state; and (3) cool down, where the solidified part continues to cool to ambient conditions. While these phases may appear to be separate and distinct, temporal overlaps do exist between phases (e.g., local solidification occurring during mold filling), and some phenomenological events are affected by others (e.g., residual stresses depend on solidification and cooling rates). Therefore, a reliable code must accurately model all three phases and the interactions between each. While many codes have been developed (to various stages of complexity) to model the solidification and cool down phases, only a few codes have been developed to model mold filling.

Photoémission de Csl induite par une impulsion laser intense femtoseconde

NASA Astrophysics Data System (ADS)

Belsky, A.; Vasil'Ev, A.; Yatsenko, B.; Bachau, H.; Martin, P.; Geoffroy, G.; Guizard, S.

2003-06-01

Nous avons mesuré pour la première fois les spectres de photoélectrons émis par un cristal isolant à large bande interdite, Csl, avec une dynamique de 10^6 coups/s, excité par la source laser haute cadence du C.E.L.I.A (800 nm, 40 fs, 1 kHz, 1 TW). L'émission d'électrons jusqu'à des énergies de quelques dizaines d'électrons-volts a été observée pour des impulsions d'éclairement compris entre 0.5 et 3 TW/cm^2, relativement faible donc par comparaison aux éclairements utilisés pour accélérer les électrons d'un atome aux mêmes énergies. Ces spectres contiennent tous, en particulier, deux bandes dans le domaine des basses énergies d'électrons (<5 eV), également observées lors d'études précédentes. Les électrons les plus énergétiques forment un plateau intense légèrement structuré et limité par une coupure exponentielle. Pour des impulsions de 3 TW/cm^2 cette coupure est située à 27 eV. L'insuffisance du mécanisme électron-photon-phonon, considéré jusqu'à présent comme le principal processus d'échauffement des électrons dans les solides en interaction non destructrice avec un champ laser, nous a poussé à proposer un mécanisme alternatif. Ce modèle met en évidence les transitions directes multiphotoniques dans la bande de conduction du solide qui sont incontournables du fait de sa structure électronique multi-branches

Étude par RMN à l'état solide de catalyseurs oxydes du type Mo-P-Al

NASA Astrophysics Data System (ADS)

Quartararo, J.; Rigole, M.; Guelton, M.; Amoureux, J. P.; Grimblot, J.

1999-10-01

Solid state 27Al NMR and especially 27Al MQMAS is used to characterize the oxide Mo-P-Al hydrotreating catalysts. This application shows that NMR is an efficient method to determine the local structure of the elements in the amorphous catalysts. So, this permits to conclude that the association of the Mo and the P leads to the formation of aluminium phosphates and that differences in the structure depend on the method of preparation. La RMN du solide et notamment la méthode “MQMAS" de 27Al est utilisée pour caractériser en détail les catalyseurs d'hydrotraitement du type Mo-P-Al sous forme oxyde. Cette application montre que la RMN est un outil efficace pour déterminer la structure locale des éléments introduits dans les catalyseurs de caractère amorphe. Ainsi, elle permet d'établir que le Mo associé au P induit la formation de phosphates d'aluminium. Des différences de structure en fonction de la méthode de préparation sont également observées.

Cavitation During Superplastic Forming

PubMed Central

Campbell, John

2011-01-01

Cavitation is the opening of pores during superplastic forming, typically at grain boundary triple points or on second phase grain boundary particles during slip of grain boundaries. Theories for the initiation of cavitation are reviewed. It seems that cavitation is unlikely to occur by processes intrinsic to metals such as dislocation mechanisms or point defect condensation. It is proposed that cavitation can only occur at non-bonded interfaces such as those introduced extrinsically (i.e., from the outside) during the original casting of the metal. These defects, known as oxide bifilms, are naturally introduced during pouring of the liquid metal, and are frozen into the solid, often pushed by dendritic growth into grain boundaries where they are difficult to detect because of their extreme thinness, often measured in nanometres. Their unbonded central interface acts as a crack and can initiate cavitation. Second phase precipitates probably do not nucleate and grow on grain boundaries but grow on bifilms in the boundaries, explaining the apparent association between boundaries, second phase particles and failure initiation. Improved melting and casting techniques can provide metal with reduced or zero bifilm population for which cavitation would not be possible, promising significant improvements in superplastic behaviour. PMID:28824142

Cavitation During Superplastic Forming.

PubMed

Campbell, John

2011-07-08

Cavitation is the opening of pores during superplastic forming, typically at grain boundary triple points or on second phase grain boundary particles during slip of grain boundaries. Theories for the initiation of cavitation are reviewed. It seems that cavitation is unlikely to occur by processes intrinsic to metals such as dislocation mechanisms or point defect condensation. It is proposed that cavitation can only occur at non-bonded interfaces such as those introduced extrinsically (i.e., from the outside) during the original casting of the metal. These defects, known as oxide bifilms, are naturally introduced during pouring of the liquid metal, and are frozen into the solid, often pushed by dendritic growth into grain boundaries where they are difficult to detect because of their extreme thinness, often measured in nanometres. Their unbonded central interface acts as a crack and can initiate cavitation. Second phase precipitates probably do not nucleate and grow on grain boundaries but grow on bifilms in the boundaries, explaining the apparent association between boundaries, second phase particles and failure initiation. Improved melting and casting techniques can provide metal with reduced or zero bifilm population for which cavitation would not be possible, promising significant improvements in superplastic behaviour.

Field Trial Data Analysis and Testing (FiTAT) Tool

DTIC Science & Technology

2011-10-01

amplitude/phase pour chaque antenne du réseau) contenu dans les données acquises pourrait être faite par FiTAT et utilisé dans PAASoM pour déterminer...identity matrix, k is the loop gain, φ is the correlation matrix of the incident signals and T = [1 0 . . . 0]T . The length of vector T is equal to the

Conductivite dans le modele de Hubbard bi-dimensionnel a faible couplage

NASA Astrophysics Data System (ADS)

Bergeron, Dominic

Le modele de Hubbard bi-dimensionnel (2D) est souvent considere comme le modele minimal pour les supraconducteurs a haute temperature critique a base d'oxyde de cuivre (SCHT). Sur un reseau carre, ce modele possede les phases qui sont communes a tous les SCHT, la phase antiferromagnetique, la phase supraconductrice et la phase dite du pseudogap. Il n'a pas de solution exacte, toutefois, plusieurs methodes approximatives permettent d'etudier ses proprietes de facon numerique. Les proprietes optiques et de transport sont bien connues dans les SCHT et sont donc de bonne candidates pour valider un modele theorique et aider a comprendre mieux la physique de ces materiaux. La presente these porte sur le calcul de ces proprietes pour le modele de Hubbard 2D a couplage faible ou intermediaire. La methode de calcul utilisee est l'approche auto-coherente a deux particules (ACDP), qui est non-perturbative et inclue l'effet des fluctuations de spin et de charge a toutes les longueurs d'onde. La derivation complete de l'expression de la conductivite dans l'approche ACDP est presentee. Cette expression contient ce qu'on appelle les corrections de vertex, qui tiennent compte des correlations entre quasi-particules. Pour rendre possible le calcul numerique de ces corrections, des algorithmes utilisant, entre autres, des transformees de Fourier rapides et des splines cubiques sont developpes. Les calculs sont faits pour le reseau carre avec sauts aux plus proches voisins autour du point critique antiferromagnetique. Aux dopages plus faibles que le point critique, la conductivite optique presente une bosse dans l'infrarouge moyen a basse temperature, tel qu'observe dans plusieurs SCHT. Dans la resistivite en fonction de la temperature, on trouve un comportement isolant dans le pseudogap lorsque les corrections de vertex sont negligees et metallique lorsqu'elles sont prises en compte. Pres du point critique, la resistivite est lineaire en T a basse temperature et devient progressivement proportionnelle a T 2 a fort dopage. Quelques resultats avec sauts aux voisins plus eloignes sont aussi presentes. Mots-cles: Hubbard, point critique quantique, conductivite, corrections de vertex

Numerical simulation on semi-solid die-casting of magnesium matrix composite based on orthogonal experiment

NASA Astrophysics Data System (ADS)

Liu, Huihui; He, Xiongwei; Guo, Peng

2017-04-01

Three factors (pouring temperature, injection speed and mold temperature) were selected to do three levels L9 (33)orthogonal experiment, then simulate processing of semi-solid die-casting of magnesium matrix composite by Flow-3D software. The stress distribution, temperature field and defect distribution of filling process were analyzed to find the optimized processing parameter with the help of orthogonal experiment. The results showed that semi-solid has some advantages of well-proportioned stress and temperature field, less defect concentrated in the surface. The results of simulation were the same as the experimental results.

Developpement d'une methode de Monte Carlo dependante du temps et application au reacteur de type CANDU-6

NASA Astrophysics Data System (ADS)

Mahjoub, Mehdi

La resolution de l'equation de Boltzmann demeure une etape importante dans la prediction du comportement d'un reacteur nucleaire. Malheureusement, la resolution de cette equation presente toujours un defi pour une geometrie complexe (reacteur) tout comme pour une geometrie simple (cellule). Ainsi, pour predire le comportement d'un reacteur nucleaire,un schema de calcul a deux etapes est necessaire. La premiere etape consiste a obtenir les parametres nucleaires d'une cellule du reacteur apres une etape d'homogeneisation et condensation. La deuxieme etape consiste en un calcul de diffusion pour tout le reacteur en utilisant les resultats de la premiere etape tout en simplifiant la geometrie du reacteur a un ensemble de cellules homogenes le tout entoure de reflecteur. Lors des transitoires (accident), ces deux etapes sont insuffisantes pour pouvoir predire le comportement du reacteur. Comme la resolution de l'equation de Boltzmann dans sa forme dependante du temps presente toujours un defi de taille pour tous types de geometries,un autre schema de calcul est necessaire. Afin de contourner cette difficulte, l'hypothese adiabatique est utilisee. Elle se concretise en un schema de calcul a quatre etapes. La premiere et deuxieme etapes demeurent les memes pour des conditions nominales du reacteur. La troisieme etape se resume a obtenir les nouvelles proprietes nucleaires de la cellule a la suite de la perturbation pour les utiliser, au niveau de la quatrieme etape, dans un nouveau calcul de reacteur et obtenir l'effet de la perturbation sur le reacteur. Ce projet vise a verifier cette hypothese. Ainsi, un nouveau schema de calcul a ete defini. La premiere etape de ce projet a ete de creer un nouveau logiciel capable de resoudre l'equation de Boltzmann dependante du temps par la methode stochastique Monte Carlo dans le but d'obtenir des sections efficaces qui evoluent dans le temps. Ce code a ete utilise pour simuler un accident LOCA dans un reacteur nucleaire de type CANDU-6. Les sections efficaces dependantes du temps ont ete par la suite utilisees dans un calcul de diffusion espace-temps pour un reacteur CANDU-6 subissant un accident de type LOCA affectant la moitie du coeur afin d'observer son comportement durant toutes les phases de la perturbation. Dans la phase de developpement, nous avons choisi de demarrer avec le code OpenMC, developpe au MIT,comme plateforme initiale de developpement. L'introduction et le traitement des neutrons retardes durant la simulation ont presente un grand defi a surmonter. Il est important de noter que le code developpe utilisant la methode Monte Carlo peut etre utilise a grande echelle pour la simulation de tous les types des reacteurs nucleaires si les supports informatiques sont disponibles.

Crystal accumulation in the Hanford Waste Treatment Plant high level waste melter. Preliminary settling and resuspension testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K. M.; Fowley, M. D.; Miller, D. H.

2016-05-01

The full-scale, room-temperature Hanford Tank Waste Treatment and Immobilization Plant (WTP) High-Level Waste (HLW) melter riser test system was successfully operated with silicone oil and magnetite particles at a loading of 0.1 vol %. Design and construction of the system and instrumentation, and the selection and preparation of simulant materials, are briefly reviewed. Three experiments were completed. A prototypic pour rate was maintained, based on the volumetric flow rate. Settling and accumulation of magnetite particles were observed at the bottom of the riser and along the bottom of the throat after each experiment. The height of the accumulated layer atmore » the bottom of the riser, after the first pouring experiment, approximated the expected level given the solids loading of 0.1 vol %. More detailed observations of particle resuspension and settling were made during and after the third pouring experiment. The accumulated layer of particles at the bottom of the riser appeared to be unaffected after a pouring cycle of approximately 15 minutes at the prototypic flow rate. The accumulated layer of particles along the bottom of the throat was somewhat reduced after the same pouring cycle. Review of the time-lapse recording showed that some of the settling particles flow from the riser into the throat. This may result in a thicker than expected settled layer in the throat.« less

Modeling of Impact Properties of Auxetic Materials: Phase 1

DTIC Science & Technology

2013-08-01

avantages marqués comparativement aux matériaux techniques classiques. La présente étude avait pour objectifs de mieux comprendre le comportement des...possible benefits of incorporating auxetic materials into lightweight armour designs . New armour designs incorporating novel auxetic materials may...Poisson négatif et ils offriraient, pour certaines applications, des avantages marqués comparativement aux matériaux techniques classiques. La présente

Combustion of Solid Propellants (La Combustion des Propergols Solides)

DTIC Science & Technology

1991-07-01

cin~tiques initiales. Il relatives A Ia granulom ~trie ct la surface eat s~me possible dWaller plus loin et sp~cifique des catalyseurs existent, il est...grand nombro do vari~t~s granulom ~triques des proporgols. On pout ainsi observer uno mont donc utilis~es induatriellemont pour notte influence du temps...et do la ajuster la vitosso des vari~tds do tempdrature do laminage sur la diminution granulom ~trie moyenno 400, 200, 100, 10, 3 de l’exposant do

Etudes optiques de nouveaux materiaux laser: Des orthosilicates dopes a l'ytterbium: Le yttrium (lutetium,scandium) pentoxide de silicium

NASA Astrophysics Data System (ADS)

Denoyer, Aurelie

La decouverte et l'elaboration de nouveaux materiaux laser solides suscitent beaucoup d'interet parmi la communaute scientifique. En particulier les lasers dans la gamme de frequence du micron debouchent sur beaucoup d'applications, en telecommunication, en medecine, dans le domaine militaire, pour la, decoupe des metaux (lasers de puissance), en optique non lineaire (doublage de frequence, bistabilite optique). Le plus couramment utilise actuellement est le Nd:YAG dans cette famille de laser, mais des remplacants plus performants sont toujours recherches. Les lasers a base d'Yb3+ possedent beaucoup d'avantages compares aux lasers Nd3+ du fait de leur structure electronique simple et de leur deterioration moins rapide. Parmi les matrices cristallines pouvant accueillir l'ytterbium, les orthosilicates Yb:Y 2SiO5, Yb:Lu2SiO5 et Yb:Sc2SiO 5 se positionnent tres bien, du fait de leur bonne conductivite thermique et du fort eclatement de leur champ cristallin necessaire a l'elaboration de lasers quasi-3 niveaux. De plus l'etude fine et systematique des proprietes microscopiques de nouveaux materiaux s'avere toujours tres interessante du point de vue de la recherche fondamentale, c'est ainsi que de nouveaux modeles sont concus (par exemple pour le champ cristallin) ou que de nouvelles proprietes inhabituelles sont decouvertes, menant a de nouvelles applications. Ainsi d'autres materiaux dopes a l'ytterbium sont connus pour leurs proprietes de couplage electron-phonon, de couplage magnetique, d'emission cooperative ou encore de bistabilite optique, mais ces proprietes n'ont encore jamais ete mises en evidence dans Yb:Y 2SiO5, Yb:Lu2SiO5 et Yb:Sc2SiO 5. Ainsi, cette these a pour but l'etude des proprietes optiques et des interactions microscopiques dans Yb:Y2SiO 5, Yb:Lu2SiO5 et Yb:Sc2SiO5. Nous utilisons principalement les techniques d'absorption IR et de spectroscopie Raman pour determiner les excitations du champ cristallin et les modes de vibration dans le materiau. Des mesures optiques sous champ magnetique ont egalement ete effectuees dans le but de caracteriser le comportement de ces excitations lorsqu'elles sont soumises a l'effet Zeeman. La resonance paramagnetique electronique a permis de completer cette etude de l'eclatement Zeeman suivant toutes les orientations du cristal. Enfin la fluorescence par excitation selective et la fluorescence induite par Raman FT, completent la description des niveaux d'energie et revelent l'existence d'emission cooperative de deux ions Yb3+ et de transferts d'energie. Les resultats de cette these apportent une contribution originale dans le domaine des nouveaux materiaux lasers par l'etude et la comprehension des interactions fines et des proprietes microscopiques d'un materiau en particulier. Ils debouchent a la fois sur des applications possibles dans le domaine de l'optique et des lasers, et sur la comprehension d'aspects fondamentaux. Cette these a prouve l'interet de ces matrices pour leur utilisation comme lasers solides: un fort eclatement du champ cristallin favorable a l'elaboration de laser quasi-3 niveaux, et de larges bandes d'absorption (dues a un fort couplage electron-phonon et a des raies satellites causees par une interaction d'echange entre deux ions Yb3+) qui permettent la generation d'impulsions laser ultra-courtes, l'accordabilite du laser, etc. De plus la miniaturisation des lasers est possible pour l'optique integree grace a des couches minces synthetisees par epitaxie en phase liquide dont nous avons demontre la tres bonne qualite structurale et l'ajustement possible de certains parametres. Nous avons reconstruit le tenseur g du niveau fondamental (qui donne des informations precieuses sur les fonctions d'onde), ceci dans le but d'aider les theoriciens a concevoir un modele de champ cristallin valide. Plusieurs mecanismes de transferts d'energie ont ete mis en evidence: un mecanisme de relaxation d'un site vers l'autre, un mecanisme d'emission cooperative, et un mecanisme d'excitation de l'Yb3+ par le Tm3+ (impurete presente dans le materiau). Ces transferts sont plutot nefastes pour la fabrication d'un laser mais sont interessants pour l'optique non lineaire (doublage de frequence, memoires optiques). Enfin, plusieurs elements (le couplage magnetique de paire, le couplage electron-phonon et l'emission cooperative) nous ont permis de conclure sur le caractere covalent de la matrice. Nous avons d'ailleurs demontre ici le role de la covalence dans l'emission cooperative, transition habituellement attribuee aux interactions multipolaires electriques.

Modelisation par elements finis du muscle strie

NASA Astrophysics Data System (ADS)

Leonard, Mathieu

Ce present projet de recherche a permis. de creer un modele par elements finis du muscle strie humain dans le but d'etudier les mecanismes engendrant les lesions musculaires traumatiques. Ce modele constitue une plate-forme numerique capable de discerner l'influence des proprietes mecaniques des fascias et de la cellule musculaire sur le comportement dynamique du muscle lors d'une contraction excentrique, notamment le module de Young et le module de cisaillement de la couche de tissu conjonctif, l'orientation des fibres de collagene de cette membrane et le coefficient de poisson du muscle. La caracterisation experimentale in vitro de ces parametres pour des vitesses de deformation elevees a partir de muscles stries humains actifs est essentielle pour l'etude de lesions musculaires traumatiques. Le modele numerique developpe est capable de modeliser la contraction musculaire comme une transition de phase de la cellule musculaire par un changement de raideur et de volume a l'aide des lois de comportement de materiau predefinies dans le logiciel LS-DYNA (v971, Livermore Software Technology Corporation, Livermore, CA, USA). Le present projet de recherche introduit donc un phenomene physiologique qui pourrait expliquer des blessures musculaires courantes (crampes, courbatures, claquages, etc.), mais aussi des maladies ou desordres touchant le tissu conjonctif comme les collagenoses et la dystrophie musculaire. La predominance de blessures musculaires lors de contractions excentriques est egalement exposee. Le modele developpe dans ce projet de recherche met ainsi a l'avant-scene le concept de transition de phase ouvrant la porte au developpement de nouvelles technologies pour l'activation musculaire chez les personnes atteintes de paraplegie ou de muscles artificiels compacts pour l'elaboration de protheses ou d'exosquelettes. Mots-cles Muscle strie, lesion musculaire, fascia, contraction excentrique, modele par elements finis, transition de phase

Caractérisation et optimisation d'états intriqués générés par un Oscillateur Paramétrique Optique à auto-verrouillage de phase

NASA Astrophysics Data System (ADS)

Laurat, J.; Keller, G.; Oliveira-Huguenin, J.-A.; Fabre, C.; Coudreau, T.

2006-10-01

Nous générons et caractérisons des faisceaux intriqués dégénérés en fréquence à l'aide d'un dispositif original appelé Oscillateur Paramétrique Optique à auto-verrouillage de phase. Nous avons ainsi obtenu des faisceaux intriqués pour lesquels ”l'inséparabilité" vaut 0.33 ± 0.02. Nous avons utilisé le formalisme des matrices de covariance pour déterminer la transformation ”non-locale" à appliquer à ces faisceaux afin d'en extraire le maximum d'intrication.

Bistatic Synthetic Aperture Radar, TIF - Report (Phase 1)

DTIC Science & Technology

2004-11-01

Cette recherche permet d’obtenir une compr6hension en profondeur des capacit6s et des difficult6s associ6es aux concepts du ROS bistatique et...Radar (SAR) Bistatic SAR Performance Analysis Defence R&D Canada R & D pour la defense Canada Canada’s Leader in Defence Chef de file au Canada en ...I 1f1 Defence Research and Recherche et developpement Development Canada pour la defense Canada DEFENCE DEFENSE Bistatic Synthetic Aperture Radar TIF

Development of a Dynamic Biomechanical Model for Load Carriage: Phase II Part A: Initial Development of a Novel Strap Tension Sensor

DTIC Science & Technology

2005-08-01

substantielle » et pourrait de ce fait être breveté. D’autres avenues (que le brevetage) sont possibles pour la commercialisation du dispositif en...breveté. D’autres avenues (que le brevetage) sont possibles pour la commercialisation du dispositif en protégeant certains de ses aspects au moyen...information: 1. INVENTOR(S) A. University Name Dept. Faculty Phone Susan A. Reid, School of Physical and Health Education

GAS-PHASE OXIDATION PRODUCTS OF BIPHENYL AND POLYCHLORINATED BIPHENYLS (R825377)

EPA Science Inventory

Our laboratory recently measured the gas-phase reaction rate constants of
polychlorinated biphenyls (PCBs) with the hydroxyl radical (OH) and concluded
that OH reactions are the primary removal pathway of PCBs from the atmosphere.
With the reaction system previousl...

Modélisation des charges d'espace dans les isolants solides par une analyse spectrale

NASA Astrophysics Data System (ADS)

Haas, V.; Scouarnec, Ch.; Franceschi, J. L.

1998-01-01

A mathematical method based on spectral algebra is developped for the thermal modulation method. These methods permit to measure the space charge distribution in solid insulators. The modelling presented permits to evaluate the performances and the limitations of the measurement method. Une linéarisation par l'algèbre spectrale a été développée dans une méthode de modulation thermique pour mesurer la distribution des charges électriques dans les isolants solides. La modélisation présentée permet d'évaluer les performances et les limites tant numériques que physiques de la méthode de mesure.

M324 : investigation of closure pour elimination for phased construction of steel girder bridges.

DOT National Transportation Integrated Search

2014-10-01

Phased construction is a common practice used by State DOTs during the : replacement of a bridge. This method allows for the traffic flow to be maintained on half : of the bridge while a new deck is constructed on the other half. For steel girder bri...

16 CFR 1500.43a - Method of test for flashpoint of volatile flammable materials.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) below the target temperature, remove the cooling block and quickly dry the cup with a paper tissue to... (cooling) fluid is solid carbon dioxide (dry ice) and acetone. If the refrigerant charged cooling module is... pouring acetone. Use only in a well-ventilated area. Avoid inhalation and contact with the eyes or skin...

Developpement de techniques numeriques pour l'estimation, la modelisation et la prediction de proprietes thermodynamiques et structurales de systems metalliques a fort ordonnancement chimique

NASA Astrophysics Data System (ADS)

Harvey, Jean-Philippe

In this work, the possibility to calculate and evaluate with a high degree of precision the Gibbs energy of complex multiphase equilibria for which chemical ordering is explicitly and simultaneously considered in the thermodynamic description of solid (short range order and long range order) and liquid (short range order) metallic phases is studied. The cluster site approximation (CSA) and the cluster variation method (CVM) are implemented in a new minimization technique of the Gibbs energy of multicomponent and multiphase systems to describe the thermodynamic behaviour of metallic solid solutions showing strong chemical ordering. The modified quasichemical model in the pair approximation (MQMPA) is also implemented in the new minimization algorithm presented in this work to describe the thermodynamic behaviour of metallic liquid solutions. The constrained minimization technique implemented in this work consists of a sequential quadratic programming technique based on an exact Newton’s method (i.e. the use of exact second derivatives in the determination of the Hessian of the objective function) combined to a line search method to identify a direction of sufficient decrease of the merit function. The implementation of a new algorithm to perform the constrained minimization of the Gibbs energy is justified by the difficulty to identify, in specific cases, the correct multiphase assemblage of a system where the thermodynamic behaviour of the equilibrium phases is described by one of the previously quoted models using the FactSage software (ex.: solid_CSA+liquid_MQMPA; solid1_CSA+solid2_CSA). After a rigorous validation of the constrained Gibbs energy minimization algorithm using several assessed binary and ternary systems found in the literature, the CVM and the CSA models used to describe the energetic behaviour of metallic solid solutions present in systems with key industrial applications such as the Cu-Zr and the Al-Zr systems are parameterized using fully consistent thermodynamic an structural data generated from a Monte Carlo (MC) simulator also implemented in the framework of this project. In this MC simulator, the modified embedded atom model in the second nearest neighbour formalism (MEAM-2NN) is used to describe the cohesive energy of each studied structure. A new Al-Zr MEAM-2NN interatomic potential needed to evaluate the cohesive energy of the condensed phases of this system is presented in this work. The thermodynamic integration (TI) method implemented in the MC simulator allows the evaluation of the absolute Gibbs energy of the considered solid or liquid structures. The original implementation of the TI method allowed us to evaluate theoretically for the first time all the thermodynamic mixing contributions (i.e., mixing enthalpy and mixing entropy contributions) of a metallic liquid (Cu-Zr and Al-Zr) and of a solid solution (face-centered cubic (FCC) Al-Zr solid solution) described by the MEAM-2NN. Thermodynamic and structural data obtained from MC and molecular dynamic simulations are then used to parameterize the CVM for the Al-Zr FCC solid solution and the MQMPA for the Al-Zr and the Cu-Zr liquid phase respectively. The extended thermodynamic study of these systems allow the introduction of a new type of configuration-dependent excess parameters in the definition of the thermodynamic function of solid solutions described by the CVM or the CSA. These parameters greatly improve the precision of these thermodynamic models based on experimental evidences found in the literature. A new parameterization approach of the MQMPA model of metallic liquid solutions is presented throughout this work. In this new approach, calculated pair fractions obtained from MC/MD simulations are taken into account as well as configuration-independent volumetric relaxation effects (regular like excess parameters) in order to parameterize precisely the Gibbs energy function of metallic melts. The generation of a complete set of fully consistent thermodynamic, physical and structural data for solid, liquid, and stoichiometric compounds and the subsequent parameterization of their respective thermodynamic model lead to the first description of the complete Al-Zr phase diagram in the range of composition [0 ≤ XZr ≤ 5 / 9] based on theoretical and fully consistent thermodynamic properties. MC and MD simulations are performed for the Al-Zr system to define for the first time the precise thermodynamic behaviour of the amorphous phase for its entire range of composition. Finally, all the thermodynamic models for the liquid phase, the FCC solid solution and the amorphous phase are used to define conditions based on thermodynamic and volumetric considerations that favor the amorphization of Al-Zr alloys.

Solid-phase microextraction followed by gas chromatography-mass spectrometry for the determination of ink photo-initiators in packed milk.

PubMed

Negreira, N; Rodríguez, I; Rubí, E; Cela, R

2010-06-30

A novel, single step method for the determination of seven ink photo-initiators in carton packed milk samples is described. Solid-phase microextraction (SPME) and gas chromatography (GC), combined with mass spectrometry (MS), were used as sample preparation and determination techniques, respectively. Parameters affecting the performance of the microextraction process were thoroughly evaluated using uni- and multivariate optimization strategies, based on the use of experimental factorial designs. The coating of the SPME fibre, together with the sampling mode and the temperature were the factors playing a major influence on the efficiency of the extraction. Under final conditions, 1.5 mL of milk and 8.5 mL of ultrapure water were poured in a glass vessel, which was closed and immersed in a water boiling bath. A poly(dimethylsiloxane)-divinylbenzene (PDMS-DVB) coated fibre was exposed directly to the diluted sample for 40 min. After that, the fibre was desorbed in the injector of the GC-MS system for 3 min. The optimized method provided limits of quantification (LOQs) between 0.2 and 1 microg L(-1) and a good linearity in the range between 1 and 250 microg L(-1). The inter-day precision remained below 15% for all compounds in spiked whole milk. The efficiency of the extraction changed for whole, semi-skimmed and skimmed milk; however, no differences were noticed among the relative recoveries achieved for milk samples, from different brands, with the same fat content. Copyright 2010 Elsevier B.V. All rights reserved.

Five-month-old infants have expectations for the accumulation of nonsolid substances.

PubMed

Anderson, Erin M; Hespos, Susan J; Rips, Lance J

2018-06-01

Infants fail to represent quantities of non-cohesive substances in paradigms where they succeed with solid objects. Some investigators have interpreted these results as evidence that infants do not yet have representations for substances. More recent research, however, shows that 5-month-old infants expect objects and substances to behave and interact in different ways. In the present experiments, we test whether infants have expectations for substances when the outcomes are not simply the opposite of those for objects. In Experiment 1, we find that 5-month-old infants expect that when a cup of sand pours behind a screen, it will accumulate in just one pile rather than two. Similarly, infants expect that when two cups of sand pour in separate streams, two distinct piles will accumulate rather than one. Infants look significantly longer at outcomes with an inconsistent number of piles, providing evidence that infants have expectations for how sand accumulates. To test whether the number of cups or the number of pours guided expectations about accumulation, Experiment 2 placed these cues in conflict. This resulted in chance performance, suggesting that, for infants to build expectations about these outcomes, they need both cues (cup and pour) to converge. These findings offer insight into the nature of infants' representations for non-cohesive substances like sand. Copyright © 2018 Elsevier B.V. All rights reserved.

Marginal Matter

NASA Astrophysics Data System (ADS)

van Hecke, Martin

2013-03-01

All around us, things are falling apart. The foam on our cappuccinos appears solid, but gentle stirring irreversibly changes its shape. Skin, a biological fiber network, is firm when you pinch it, but soft under light touch. Sand mimics a solid when we walk on the beach but a liquid when we pour it out of our shoes. Crucially, a marginal point separates the rigid or jammed state from the mechanical vacuum (freely flowing) state - at their marginal points, soft materials are neither solid nor liquid. Here I will show how the marginal point gives birth to a third sector of soft matter physics: intrinsically nonlinear mechanics. I will illustrate this with shock waves in weakly compressed granular media, the nonlinear rheology of foams, and the nonlinear mechanics of weakly connected elastic networks.

Potential Re-utilization of Composted Mangrove Litters for Pond Environment Quality Improvement

NASA Astrophysics Data System (ADS)

Dwi Hastuti, Endah; Budi Hastuti, Rini; Hariyati, Riche

2018-05-01

Production of mangrove litter from pruning and thinning activities is potential source of organic materials which could be re-utilized to improve pond environment quality and fertility. This research aimed to analyze the nutrient composition compost produced from mangrove litter and to describe the effect of compost application on pond quality. This research was conducted through two phases, including composting trial and application of compost on pond trial. Composting process was conducted for 45-60 days on mangrove litter achieved from pruning activities in the silvofishery pond using composting container, while application of compost in pond was conducted by pouring 2 kg of compost in 25 m2 pond. Production of compost included solid compost and liquid compost. Nutrient concentration of solid compost was ranged from 0.47-0.52% for N; 0.36-0.44% for P; and 5.45-6.39% for organic C, while liquid compost provided 0.62-0.69%; 0.24-0.32%; and 3.98-4.45% respectively for N, P and organic C. While C/N ratio was ranged from 11.60-12.78 and 5.77-7.18 respectively for solid and liquid compost. Solid compost quality resulted that N, P and C/N ration had fulfilled the standart criteria defined by Indonesia National Standart for compost. Observed impact of compost application on pond water quality were the improvement of water clarity and increasing abundance of klekap (lab-lab). This showed that mangrove litters could be converted into a more productive materials to enhance pond environment quality and productivity, decrease management cost and increase benefit. Scheduled fertilization with compost is suggested to be conducted to provide best benefit on silvofishery management.

On the phenomenology of tilted domains in lamellar eutectic growth

NASA Astrophysics Data System (ADS)

Caroli, B.; Caroli, C.; Fauve, S.

1992-03-01

We show that, due to the coupling between tilt (amplitude of the antisymmetric part of the font profile) and phase dynamics, the phenomenology of tilt domains of finite width proposed by Coullet et al. within the assumption of a subcritical homogeneous tilt bifurcation retains the same qualitative features when this bifurcation is direct, as is the case for lamellar eutectics. Nous montrons que, du fait du couplage entre les dynamiques d'inclinaison (amplitude de la partie impaire du profil de front) et de phase, la phénoménologie des domaines d'inclinaison de largeur finie proposée par Coullet et al. pour le cas d'une bifurcation d'inclinaison homogène sous critique garde les mêmes caractéristiques qualitatives quand cette bifurcation est directe, comme c'est le cas pour la croissance eutectique lamellaire.

MOLDS FOR CASTING PLUTONIUM

DOEpatents

Anderson, J.W.; Miley, F.; Pritchard, W.C.

1962-02-27

A coated mold for casting plutonium comprises a mold base portion of a material which remains solid and stable at temperatures as high as the pouring temperature of the metal to be cast and having a thin coating of the order of 0.005 inch thick on the interior thereof. The coating is composed of finely divided calcium fluoride having a particle size of about 149 microns. (AEC)

Calorimetric Study of Phase Transitions Involving Twist-Grain-Boundary TGB{A} and TGB{C} Phases

NASA Astrophysics Data System (ADS)

Navailles, L.; Garland, C. W.; Nguyen, H. T.

1996-09-01

High-resolution calorimetry has been used to determine the heat capacity and latent heat associated with phase transitions in the homologous series of chiral liquid crystals nF_2BTFO_1M_7 [ 3-fluoro-4(1-methylheptyloxy)4'-(4''-alkoxy-2'', 3''-difluorobenzoyloxy)tolane] . These compounds exhibit smectic-C^* (SmC^*), twist-grain-boundary (TGBA for n=10, TGBC for n=11, 12) and cholesteric (N^*) phases. All the phase transitions are first order with small to moderate latent heats. There is a large rounded excess heat capacity peak in the N^* phase that is consistent with the predicted appearance of short-range TGB order (chiral line liquid character). This is analogous to the development of an Abrikosov flux vortex liquid in type-II superconductors. Both the n=11 and 12 homologs exhibit two closely spaced transitions in the region where a single TGBC - N^* transition was expected. This suggests the existence of two thermodynamically distinct TGBC phases. Des exprériences de calorimétrie haute résolution ont été réalisées pour déterminer les chaleurs spécifiques et les chaleurs latentes associées aux transitions de phase des homologues de la série crystal liquide nF_2BTFO_1M_7: 3-fluoro-4[1-methyl-heptyloxy]4'-(4''-alcoxy-2'', 3''-difluorobenzoyloxy)tolanes. Ces produits présentent la phase smectique C^* (SmC^*), les phases à torsion par joint de grain (TGBA pour n=10 et TGBC pour n=11, 12) et la phase cholestérique (N^*). Toutes les transitions de phase sont du premier ordre. La chaleur latente associée à ces transitions est faibles ou modérée. Nous observons, dans la phase N^*, un grand pic arrondi qui est en accord avec les prédictions de l'apparition d'un ordre TGB à courte distance (liquide de ligne de dislocation). Ce phénomène est l'analogue du liquide de vortex dans les supraconducteurs de type II. Les composés n=11 et 12 présentent, dans la région où nous attendions une transition TGBC - N^* unique, deux transitions sur un très faible domaine de température. Ce résultat suggère l'existence de deux phases TGBC thermodynamiquement distinctes.

The phase diagrams of iron-based superconductors: Theory and experiments

NASA Astrophysics Data System (ADS)

Martinelli, Alberto; Bernardini, Fabio; Massidda, Sandro

2016-01-01

Phase diagrams play a primary role in the understanding of materials properties. For iron-based superconductors (Fe-SC), the correct definition of their phase diagrams is crucial because of the close interplay between their crystallochemical and magnetic properties, on one side, and the possible coexistence of magnetism and superconductivity, on the other. The two most difficult issues for understanding the Fe-SC phase diagrams are: 1) the origin of the structural transformation taking place during cooling and its relationship with magnetism; 2) the correct description of the region where a crossover between the magnetic and superconducting electronic ground states takes place. Hence a proper and accurate definition of the structural, magnetic and electronic phase boundaries provides an extremely powerful tool for material scientists. For this reason, an exact definition of the thermodynamic phase fields characterizing the different structural and physical properties involved is needed, although it is not easy to obtain in many cases. Moreover, physical properties can often be strongly dependent on the occurrence of micro-structural and other local-scale features (lattice micro-strain, chemical fluctuations, domain walls, grain boundaries, defects), which, as a rule, are not described in a structural phase diagram. In this review, we critically summarize the results for the most studied 11-, 122- and 1111-type compound systems, providing a correlation between experimental evidence and theory. Les deux difficultés principales pour la compréhension des diagrammes de phase Fe-SC sont : 1) l'origine de la transformation structurelle ayant lieu pendant le refroidissement et sa relation avec le magnétisme ; 2) la description correcte de la région où survient un recouvrement entre les états fondamentaux électroniques, magnétiques et supraconducteur électronique survient. De ce fait, une définition appropriée et précise des frontières des phases structurelle, magnétique et électronique fournit un outil extrêmement puissant pour les scientifiques du domaine des matériaux. Pour cette raison, une définition exacte des champs de phases thermodynamiques caractérisant les différentes propriétés structurelles et physiques impliquées est nécessaire, bien qu'elle ne soit pas aisée à obtenir dans de nombreux cas. De plus, les propriétés physiques peuvent souvent dépendre fortement de la survenue de caractéristiques micro-structurelles ou autres à l'échelle locale (micro-contraintes dans le réseau, fluctuations chimiques, parois de domaines, joints de grains, défauts), qui, d'ordinaire, ne sont pas décrites dans un diagramme de phases structurelles. Dans cette revue, nous résumons de manière critique les résultats obtenus pour les systèmes composites le plus étudiés de types 11, 122 et 1111, qui établissent une corrélation entre les preuves expérimentales et la théorie.

Evidence for a jacketed nematic polymer

NASA Astrophysics Data System (ADS)

Hardouin, F.; Mery, S.; Achard, M. F.; Noirez, L.; Keller, P.

1991-05-01

The evidence for a “jacketed” structure at the scale of the chain dimensions in the nematic phase of a “side-on fixed” liquid crystal polysiloxane is reported by using small angle neutron scattering. We relate this anisotropy of chain conformation to the first measurements of the rotational viscosity coefficient in this new type of liquid crystal side-chain polymer. Par des mesures de diffusion des neutrons aux petits angles nous montrons l'existence, pour un polysiloxane “ en haltère ”, d'une structure “ chemisée ” à l'échelle de l'organisation global d'une chaîne en phase nématique. On constate que cette anisotropie de forme du polymère a des conséquences sur l'évolution du coefficient de viscosité de torsion mesuré pour la première fois dans ce nouveau type de polymère à chaînes latérales.

Extracting topographic structure from digital elevation data for geographic information-system analysis

USGS Publications Warehouse

Jenson, Susan K.; Domingue, Julia O.

1988-01-01

The first phase of analysis is a conditioning phase that generates three data sets: the original OEM with depressions filled, a data set indicating the flow direction for each cell, and a flow accumulation data set in which each cell receives a value equal to the total number of cells that drain to it. The original OEM and these three derivative data sets can then be processed in a variety of ways to optionally delineate drainage networks, overland paths, watersheds for userspecified locations, sub-watersheds for the major tributaries of a drainage network, or pour point linkages between watersheds. The computer-generated drainage lines and watershed polygons and the pour point linkage information can be transferred to vector-based geographic information systems for futher analysis. Comparisons between these computergenerated features and their manually delineated counterparts generally show close agreement, indicating that these software tools will save analyst time spent in manual interpretation and digitizing.

Equations of State and High-Pressure Phases of Explosives

NASA Astrophysics Data System (ADS)

Peiris, Suhithi M.; Gump, Jared C.

Energetic materials, being the collective name for explosives, propellants, pyrotechnics, and other flash-bang materials, span a wide range of composite chemical formulations. Most militarily used energetics are solids composed of particles of the pure energetic material held together by a binder. Commonly used binders include various oils, waxes, and polymers or plasticizers, and the composite is melt cast, cured, or pressed to achieve the necessary mechanical properties (gels, putties, sheets, solid blocks, etc.) of the final energetic material. Mining, demolition, and other industries use liquid energetics that are similarly composed of an actual energetic material or oxidizer together with a fuel, that is to be mixed and poured for detonation. Pure energetic materials that are commonly used are nitroglycerine, ammonium nitrate, ammonium or sodium perchlorate, trinitrotoluene (TNT), HMX, RDX, and TATB. All of them are molecular materials or molecular ions that when initiated or insulted undergoes rapid decomposition with excessive liberation of heat resulting in the formation of stable final products. When the final products are gases, and they are rapidly produced, the sudden pressure increase creates a shock wave. When decomposition is so rapid that the reaction moves through the explosive faster than the speed of sound in the unreacted explosive, the material is said to detonate. Typically, energetic materials that undergo detonation are known as high explosives (HEs) and energetic materials that burn rapidly or deflagrate are known as low explosives and/or propellants.

Study of the Electric Field-Induced Low Temperature Phase in Pb(Mg_{1/3}Nb_{2/3})O_3: Titanium Influence

NASA Astrophysics Data System (ADS)

Bidault, O.; Husson, E.; Gaucher, P.

1997-06-01

The temperature dependence of the dielectric permittivity under a dc electric field is studied in (1 - x)Pb(Mg{1/3}Nb{2/3})O3-xPbTiO3 ceramics (0 leq x leq 0.1). The size of the ordered regions, which is the key parameter to understand the dielectric response of such materials, is suggested to be reduced by T_i doping. A ferroelectric transition can be induced by a field E from the average cubic phase. Whereas PMN is a relaxor undergoing a macroscopic phase transition only if E > 4 kV cm^{-1}, materials with x = 0.1 exhibit a spontaneous cubic to rhombohedral transition at 280 K on cooling. Moreover, in all the studied samples, the T_f temperature deduced from the Vogel-Fulcher relation is found to be very close to the poling temperature under high field. La variation en température de la constante diélectrique de céramiques de composition (1 - x)Pb(Mg{1/3}Nb{2/3})O{3}-xPbTiO3 (0 leq x leq 0,1) est étudiée alors qu'un champ dc est appliqué à l'échantillon. La taille des régions ordonnées, paramètre-clé pour comprendre la réponse du matériau, est réduite par l'introduction de titane. Une transition de phase ferroélectrique peut être induite sous champ à partir de la phase cubique en moyenne. Si PMN est un relaxeur, ne transitant qu'à condition d'avoir E > 4 kV cm^{-1}, la transition cubique to rhomboèdrique devient spontanée pour PMN: 10% T_i (à 280 K au refroidissement). De plus, pour tous les échantillons, la température T_f, déduite de la relation de Vogel-Fulcher est systématiquement trouvée voisine de celle d'apparition de la phase polaire sous champ.

Development of a field-friendly technique for fecal steroid extraction and storage using the African wild dog (Lycaon pictus).

PubMed

Santymire, R M; Armstrong, D M

2010-01-01

Hormonal analysis provides information about wildlife populations, but is difficult to conduct in the field. Our goal was to develop a rapid and effective field method for fecal steroid analysis by comparing: (1) three extraction methods (laboratory (LAB), homogenize (HO) and handshake (HS)) and (2) two storage methods (solid-phase extraction (SPE) tubes vs. plastic tubes (PT)). Samples (n=23) from captive African wild dogs (Lycaon pictus) were thoroughly mixed, three aliquots of each were weighed ( approximately 0.5 g) and 5 ml of 90% ethanol was added. For LAB, samples were agitated (mixer setting 60; 30 min), centrifuged (1,500 rpm; 20 min) and poured into glass tubes. Or aliquots were HO (1 min) or HS (1 min) and poured through filter paper into glass tubes. Samples were split, analyzed for corticosterone (C) and testosterone (T) metabolites using enzyme immunoassays or stored in SPE or PT. Samples were stored (room temperature) for 30, 60 or 180 days, reconstituted in buffer and analyzed. Mean C and T recoveries of HO were greater (P=0.03) than HS compared with LAB, which was similar to HO (P>0.05). After 30 days <21% of C and T was recovered from SPE, but approximately 100% of each was recovered from HO-PT and HS-PT. Similarly, after 60 and 180 days, approximately 100% of C and T was recovered from HO-PT and HS-PT. Results demonstrated that, for C and T, HO was more comparable (P<0.001) to LAB than HS and PT storage was more efficient than SPE (P<0.001). (c) 2009 Wiley-Liss, Inc.

The thermal conductance of solid-lubricated bearings at cryogenic temperatures in vacuum

NASA Technical Reports Server (NTRS)

Anderson, M. J.

1996-01-01

The thermal conductance of Hertzian contacts is of great importance to cryogenic spacecraft mechanisms such as the Infra-Red Space Observatory (ISO) and the Far Infra-Red Space Telescope (FIRST). At cryogenic temperatures, cooling of mechanism shafts and associated components occurs via conduction through the bearings. When fluid lubricants are cooled below their pour points, they no longer lubricate effectively, and it is necessary to use low shear strength solid lubricants. Currently, only very limited low temperature data exists on the thermal conductance of Hertzian contacts in both unlubricated and lubricated conditions. This paper reports on measurements of thermal conductance made on stationary ball bearings under cryo-vacuum conditions. Quantitative data is provided to support the development of computer models predicting the thermal conductance of Hertzian contacts and solid lubricants at cryogenic temperatures.

Mitigating cold flow problems of biodiesel: Strategies with additives

NASA Astrophysics Data System (ADS)

Mohanan, Athira

The present thesis explores the cold flow properties of biodiesel and the effect of vegetable oil derived compounds on the crystallization path as well as the mechanisms at play at different stages and length scales. Model systems including triacylglycerol (TAG) oils and their derivatives, and a polymer were tested with biodiesel. The goal was to acquire the fundamental knowledge that would help design cold flow improver (CFI) additives that would address effectively and simultaneously the flow problems of biodiesel, particularly the cloud point (CP) and pour point (PP). The compounds were revealed to be fundamentally vegetable oil crystallization modifiers (VOCM) and the polymer was confirmed to be a pour point depressant (PPD). The results obtained with the VOCMs indicate that two cis-unsaturated moieties combined with a trans-/saturated fatty acid is a critical structural architecture for depressing the crystallization onset by a mechanism wherein while the straight chain promotes a first packing with the linear saturated FAMEs, the kinked moieties prevent further crystallization. The study of model binary systems made of a VOCM and a saturated FAME with DSC, XRD and PLM provided a complete phase diagram including the thermal transformation lines, crystal structure and microstructure that impact the phase composition along the different crystallization stages, and elicited the competing effects of molecular mass, chain length mismatch and isomerism. The liquid-solid boundary is discussed in light of a simple thermodynamic model based on the Hildebrand equation and pair interactions. In order to test for synergies, the PP and CP of a biodiesel (Soy1500) supplemented with several VOCM and PLMA binary cocktails were measured using a specially designed method inspired by ASTM standards. The results were impressive, the combination of additives depressed CP and PP better than any single additive. The PLM and DSC results suggest that the cocktail additives are most effective when the right molecular structure and optimal concentration are provided. The cocktail mixture achieves then tiny crystals that are prevented from aggregating for an extended temperature range. The results of the study can be directly used for the design of functional and economical CFI from vegetable oils and their derivatives.

Oxygen vibrations in the series Bi2Sr2Ca{_{n-1}}Cu{n}O{_{4+2 n+y}}

NASA Astrophysics Data System (ADS)

Faulques, E.; Dupouy, P.; Lefrant, S.

1991-06-01

We present a discussion of the oxygen vibrations in the Bi{2}Sr{2}Ca{n-1}Cu{n}O{4+2 n+y} high T_c superconductors with the aim of interpreting Raman spectra in the case of the non-symmorphic Amaa structure. Group theory shows that the oxygen atoms belonging to the central CuO{2} plane generate a Raman activity for the n=1,3 phases. Consequently, we propose a novel assignment for the lines of weak intensity at 297, 316 and 333 cm^{-1}. It is shown that the two components of the 460 cm^{-1} band may be consistent with the Amma structure. Spectra recorded in crossed polarization exhibit weak lines which could be assigned to B {1g} modes expected for the three phases. Nous présentons une discussion sur les vibrations des atomes d'oxygène dans la série des supraconducteurs Bi{2}Sr{2}Ca{n-1}Cu{n}O{4+2 n+y} dans le but d'interpréter les spectres Raman. L'analyse des modes normaux de vibration de la structure Amaa pour les phases n=1 ou 3 montre que les atomes d'oxygène du plan CuO{2} contenant les centres d'inversion donnent lieu à une activité Raman. En conséquence, nous proposons une nouvelle attribution pour les raies de faible intensité à 297, 316 et 333 cm^{-1}. Nous montrons que le dédoublement de la bande à 460 cm^{-1} pourrait être dû à la structure Amaa. Les spectres enregistrés en polarization croisée montrent de faibles bandes qui peuvent être attribuées aux modes B {1g} attendus pour les trois phases.

Etude de la formation de resonances electroniques et de leur role dans la fragmentation neutre de molecules d'interet biologique

NASA Astrophysics Data System (ADS)

Lepage, Martin

1998-12-01

Cette these est presentee a la Faculte de medecine de l'Universite de Sherbrooke en vue de l'obtention du grade de Ph.D. en Radiobiologie. Elle contient des resultats experimentaux enregistres avec un spectrometre d'electrons a haute resolution. Ces resultats portent sur la formation de resonances electroniques en phase condensee et de differents canaux pour leur decroissance. En premier lieu, nous presentons des mesures d'excitations vibrationnelles de l'oxygene dilue en matrice d'argon pour des energies des electrons incidents de 1 a 20 eV. Les resultats suggerent que le temps de vie des resonances de l'oxygene est modifie par la densite d'etats d'electrons dans la bande de conduction de l'argon. Nous presentons aussi des spectres de pertes d'energie d'electrons des molecules de tetrahydrofuranne (THF) et d'acetone. Dans les deux cas, la position en energie des pertes associees aux excitations vibrationnelles est en excellent accord avec les resultats trouves dans la litterature. Les fonctions d'excitation de ces modes revelent la presence de plusieurs nouvelles resonances electroniques. Nous comparons les resonances du THF et celles de la molecule de cyclopentane en phase gazeuse. Nous proposons une origine commune aux resonances ce qui implique qu'elles ne sont pas necessairement attribuees a l'excitation des electrons non-apparies de l'oxygene du THF. Nous proposons une nouvelle methode basee sur la spectroscopie par pertes d'energie des electrons pour detecter la production de fragments neutres qui demeurent a l'interieur d'un film mince condense a basse temperature. Cette methode se base sur la detection des excitations electroniques du produit neutre. Nous presentons des resultats de la production de CO dans un film de methanol. Le taux de production de CO en fonction de l'energie incidente des electrons est calibre en termes d'une section efficace totale de diffusion des electrons. Les resultats indiquent une augmentation lineaire du taux de production de CO en fonction de l'epaisseur du film et de la dose d'electrons incidente sur le film. Ces donnees experimentales cadrent dans un modele simple ou un electron cause la fragmentation de la molecule sans reaction avec les molecules avoisinantes. Le mecanisme propose pour la fragmentation unimoleculaire du methanol est la formation de resonances qui decroissent dans un etat electronique excite. Nous suggerons l'action combinee de la presence d'un trou dans une orbitale de coeur du methanol et de la presence de deux electrons dans la premiere orbitale vide pour expliquer la dehydrogenation complete du methanol pour des energies des electrons entre 8 et 18 eV. Pour des energies plus grandes, la fragmentation par l'intermediaire de l'ionisation de la molecule a deja ete suggeree. La methode de detection des etats electroniques offre une alternative a la detection des excitations vibrationnelles puisque les spectres de pertes d'energie des electrons sont congestionnes dans cette region d'energie pour les molecules polyatomiques.

Ecoulement et mise en structure de suspensions macroscopiques

NASA Astrophysics Data System (ADS)

Petit, L.

In this review, we report the various experimental studies performed on suspensions of solid particules in liquids, and concerning the rheological behaviour of such systems and the ordering of particules under the applied velocity fields. The number of materials which are flowing suspensions (reagents in chemical engineering, paints while spreading, blood flow, muds in oil reservoir) gave rise to a number of experimental studies, especially in the last twenty years. The results show a wide variety of behaviour, even for systems of intermediate concentration. In addition, even for identical systems, the results depend of the type of flow. Then, it is clear that, in addition of the standard parameters which are to be taken into account, it is necessary to consider the type of flow the suspension is submitted to. The flow influences the spatial distribution of the particules, leading to their ordering or migration. These ordering or motions influence the flow, and then, the rheological behaviour of the whole system. So, there is a feedback mechanism from the ordering to the flow, which explains the experimental observations. Nous reportons dans cette revue les différentes études expérimentales réalisées sur les suspensions de particules solides dans un liquide et qui concernent le comportement rhéologique de ces systèmes ainsi que les mouvements des particules sous l'effet des champs de vitesse imposés. Ces mouvements peuvent conduire soit à des mises en structure, ou encore à des migrations des particules. L'importance du nombre de matériaux qui se présentent sous forme de suspension et qui sont mis en écoulement (réactif en génie chimique, peintures lors de leur mise en place, écoulement sanguin, boues dans les forages pétroliers,...) a motivé un grand nombre de travaux expérimentaux plus fondamentaux sur le sujet, particulièrement dans les vingt dernières années. Les résultats correspondants montrent une très grande diversité des comportements même pour les systèmes moyennement concentrés. Bien plus, pour des systèmes identiques, les résultats dépendent du type d'écoulement imposé. Ceci montre clairement, qu'à côté des facteurs standards qui sont à prendre en compte pour caractériser le comportement de tels systèmes (concentration de la phase solide, taille des particules, interactions entre particules, effets de diffusion,...), il est nécessaire de tenir compte de la nature de l'écoulement auquel est soumise la suspension. Cet écoulement modifie la distribution spatiale des particules, soit directement, soit par l'intermédiaire de différents mécanismes tels que écoulements secondaires, diffusion. Ces effets se traduisent par une mise en ordre des particules, ou bien à des mouvements de migration. Les structures ou les mouvements ainsi créés agissent à leur tour sur les propriétés de l'écoulement, et de là, sur le comportement rhéologique de l'ensemble du système. Il existe ainsi un mécanisme de rétroaction de la structure sur l'écoulement qui permet d'expliquer les comportements observés expérimentalement.

Contribution a l'etude et au developpement de nouvelles poudres de fonte

NASA Astrophysics Data System (ADS)

Boisvert, Mathieu

L'obtention de graphite libre dans des pieces fabriquees par metallurgie des poudres (M/P) est un defi auquel plusieurs chercheurs se sont attardes. En effet, la presence de graphite apres frittage ameliore l'usinabilite des pieces, permettant donc de reduire les couts de production, et peut aussi engendrer une amelioration des proprietes tribologiques. L'approche utilisee dans cette these pour tenter d'obtenir du graphite libre apres frittage est par l'utilisation de nouvelles poudres de fontes atomisees a l'eau. L'atomisation a l'eau etant un procede de production de poudres relativement peu couteux qui permet de grandes capacites de production, le transfert des decouvertes de ce doctorat vers des applications industrielles sera donc economiquement plus favorable. En plus de l'objectif d'obtenir du graphite libre apres frittage, un autre aspect important des travaux est le controle de la morphologie du graphite libre apres frittage. En effet, il est connu dans la litterature des fontes coulees/moulees que la morphologie du graphite influencera les proprietes des fontes, ce qui est aussi vrai pour les pieces de M/P. Les fontes ductiles, pour lesquelles le graphite est sous forme de nodules spheroidaux isoles les uns des autres, possedent des proprietes mecaniques superieures aux fontes grises pour lesquelles le graphite est sous forme lamellaire et continu dans la matrice. Les resultats presentes dans cette these montrent qu'il est possible, dans des melanges contenant des poudres de fontes, d'avoir un controle sur la morphologie du graphite et donc sur les proprietes des pieces. Le controle de la morphologie du graphite a principalement ete realise par le type de frittage et le phenomene de diffusion " uphill " du carbone cause par des gradients en silicium. En effet, pour les frittages en phase solide, tous les nodules de graphite sont presents a l'interieur des grains de poudre apres frittage. Pour les frittages en phase liquide, l'intensite de la diffusion " uphill " permet de conserver plus ou moins de graphite nodulaire a l'interieur des regions riches en silicium, alors que le reste du graphite precipite sous forme lamellaire/vermiculaire dans les regions interparticulaires. L'etude des poudres de fontes et la recherche des mecanismes regissant la morphologie du graphite dans les fontes coulees/moulees nous ont amenes a produire des poudres de fontes traitees au magnesium avant l'atomisation. Plusieurs resultats fondamentaux ont ete obtenus de la caracterisation des poudres traitees au magnesium et de leur comparaison avec des poudres de chimies similaires non traitees au magnesium. D'abord, il a ete possible d'observer des bifilms d'oxyde de silicium dans la structure du graphite primaire d'une poudre de fonte grise hypereutectique. Il s'agit des premieres images montrant la structure double de ces defauts, venant ainsi appuyer la theorie elaboree par le professeur John Campbell. Ensuite, il a ete montre que le traitement au magnesium forme une atmosphere protectrice gazeuse autogeneree qui empeche l'oxydation de la surface du bain liquide et donc, la formation et l'entrainement des bifilms. Le role du magnesium sur la morphologie du graphite est de diminuer le soufre en solution en formant des precipites de sulfure de magnesium et ainsi d'augmenter l'energie d'interface graphite-liquide. En reponse a cette grande energie d'interface graphite-liquide, le graphite cherche a minimiser son ratio surface/volume, ce qui favorise la formation de graphite spheroidal. De plus, deux types de germination ont ete observes dans la poudre de fonte hypereutectique traitee au magnesium. Le premier type est une germination heterogene sur un nombre limite de particules faites de magnesium, d'aluminium, de silicium et d'oxygene. Le deuxieme type est une germination homogene des nodules dans certaines regions du liquide plus riches en silicium. L'observation du centre reel tridimensionnel, en microscopie electronique en transmission en haute resolution, d'un des nodules ayant subi une germination homogene a permis de confirmer que le mode de croissance du graphite spheroidal se produit selon le modele de la croissance en feuille de chou. (Abstract shortened by ProQuest.).

Modified sedimentation-dispersion model for solids in a three-phase slurry column

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, D.N.; Ruether, J.A.; Shah, Y.T.

1986-03-01

Solids distribution data for a three-phase, batch-fluidized slurry bubble column (SBC) are presented, using air as the gas phase, pure liquids and solutions as the liquid phase, and glass beads and carborundum catalyst powder as the solid phase. Solids distribution data for the three-phase SBC operated in a continuous mode of operation are also presented, using nitrogen as the gas phase, water as the liquid phase, and glass beads as the solid phase. A new model to provide a reasonable approach to predict solids concentration distributions for systems containing polydispersed solids is presented. The model is a modification of standardmore » sedimentation-dispersion model published earlier. Empirical correlations for prediction of hindered settling velocity and solids dispersion coefficient for systems containing polydispersed solids are presented. A new method of evaluating critical gas velocity (CGV) from concentrations of the sample withdrawn at the same port of the SBC is presented. Also presented is a new mapping for CGV which separates the two regimes in the SBC, namely, incomplete fluidization and complete fluidization.« less

Evaluation of the Impacts of Live Fire Training at CFB Shilo

DTIC Science & Technology

2003-04-22

des activites d’entrainement faites au secteur d’entrainement de la BFC Shilo et est la suite de la phase I, effectuee en septembre 2000. Durant la...premiere phase, trois champs de bataille avaient ete echantillonnes pour evaluer la contamination par les explosifs, les metaux, les COVs et les...iv Sommaire Le contexte international de demilitarisation, de la fermeture de bases et de la severite croissante des lois environnementales a

Phase transitions and reentrant phenomena in liquid crystals having both rigid and flexible intramolecular joints

NASA Astrophysics Data System (ADS)

Pyżuk, W.; Górecka, E.; Mieczkowski, J.; Przedmojski, J.

1992-07-01

Two series of liquid-crystalline compounds having three phenyl rings separated by flexible spacer —CH(CH{3})CH{2}—COO— and by rigid azo and azoxy group, were studied by DSC, optical and X-ray methods. For esters of dl-3-(4^{prime}-nitro)-phenylbutyric acid with 4^{prime}-alkoxy-phenylazo-phenol-4 having dodecyloxy or longer terminal chains, as well as for related azoxy compounds, a narrow (even below 5 K) reentrant or inverted nematic phase appearing between partly bilayer and monolayer smectics A was observed. For higher homologues of the azoxy series additional smectic phases appear, leading to the occurrence of new multicritical points, e.g. the critical end point Ad Cd N^re. On each of the lines, which separate nematic from smectic A phases, transitions are of weakly first or second-order and more than one tricritical point can occur. On the A{1} N/A{1} N^re line, a simple N A{1} tricritical point is observed at T_NI/T_AN = 0.834. The presence of further critical points depends on the components of the binary system involved. Four of the azoxy compounds studied undergo a second order phase transition between partly bilayer smectics, Ad and Cd. Such a transition is accompanied by a jumb in the specific heat, varying linearly with the length of the molecular tails. Various temperature dependences of the layer spacing in the Ad phase are observed for subsequent homologues from the azoxy series. Plusieurs cristaux liquides composés de trois groupements phényl séparés par un groupement —CH(CH{3})CH{2}—COO—, ainsi que par des groupements azo et azoxy, ont été examinés par AED, méthodes optiques et par rayons X. Pour des esters de l'acide dl-3-(4^{prime}-nitro)phénylbutyrique et de 4^{prime}-alkoxy-phénylazo-phénol-4 ayant comme terminaison une chaîne dodecyloxy ou bien plus longue, ainsi que pour des composés azoxy relatif, on observe (même au-dessous de 5 K) une étroite phase nématique réentrante ou inverse entre les phases smectiques : monocouche et partiellement bicouche. Pour des homologues plus longs dans la série des composés azoxy, on a constaté l'existence d'autres phases smectiques ce qui implique l'apparition, sur les diagrammes des phases, de nouveau points multicritiques, par exemple le point Ad Cd N^re. Sur chaque ligne séparant les phases smectiques A de la phase nématique les transitions sont faiblement du premier ordre ou du deuxième ordre ce qui mène dans certain cas à plus qu'un point tricritique. Sur la ligne A{1} N/A{1} N^re on observe à T_NI/T_AN = 0,834 un simple point tricritique N A{1} — l'apparition des autres dépend du choix des constituants du système binaire. Dans le cas de quatre composés azoxy on a constaté une transition du deuxième ordre entre les phases smectiques partiellement bicouches, Ad et Cd. La transition est accompagnée d'un brusque changement de la chaleur spécifique qui varie linéairement avec la longueur de la queue de la molécule. Pour des homologues suivants de la série des composés azoxy on observe différentes dépendances en température de la distance entre les couches de la phase Ad.

Etude des melanges co-continus d'acide polylactique et d'amidon thermoplastique (PLA/TPS)

NASA Astrophysics Data System (ADS)

Chavez Garcia, Maria Graciela

Les melanges co-continus sont des melanges polymeriques ou chaque composant se trouve dans une phase continue. Pour cette raison, les caracteristiques de chacun des composants se combinent et il en resulte un materiau avec une morphologie et des proprietes particulieres. L'acide polylactique (PLA) et l'amidon thermoplastique (TPS) sont des biopolymeres qui proviennent de ressources renouvelables et qui sont biodegradables. Dans ce projet, differents melanges de PLA et TPS a une haute concentration de TPS ont ete prepares dans une extrudeuse bi-vis afin de generer des structures co-continues. Grace a la technique de lixiviation selective, le TPS est enleve pour creer une structure poreuse de PLA qui a pu etre analysee au moyen de la microtomographie R-X et de la microscopie electronique a balayage MEB. L'analyse des images 2D et 3D confirme la presence de la structure co-continue dans les melanges dont la concentration en TPS. se situe entre 66% et 80%. L'effet de deux plastifiants, le glycerol seul et le melange de glycerol et de sorbitol, dans la formulation de TPS est etudie dans ce travail. De plus, nous avons evalue l'effet du PLA greffe a l'anhydride maleique (PLAg) en tant que compatibilisant. On a trouve que la phase de TPS obtenue avec le glycerol est plus grande. L'effet de recuit sur la taille de phases est aussi analyse. Grace aux memes techniques d'analyse, on a etudie l'effet du procede de moulage par injection sur la morphologie. On a constate que les pieces injectees presentent une microstructure heterogene et differente entre la surface et le centre de la piece. Pres de la surface, une peau plus riche en PLA est presente et les phases de TPS y sont allongees sous forme de lamelles. Plus au centre de la piece, une morphologie plus cellulaire est observee pour chaque phase continue. L'effet des formulations sur les proprietes mecaniques a aussi ete etudie. Les pieces injectees dont la concentration de TPS est plus grande presentent une moindre resistance a la traction. La presence du compatibilisant dans la region co-continue affecte negativement cette resistance. En considerant que l'amidon est un biomateriau abondant, moins cher et plus rapidement biodegradable, son ajout dans le PLA presente l'avantage de reduire le cout tout en augmentant la vitesse de degradation du PLA. De plus, une structure continue poreuse de PLA produit par la technique de lixiviation selective a des applications potentielles soit comme materiau a degradation rapide ou encore, une fois la phase TPS retiree, comme substrat a porosite ouverte pour la fabrication de membranes, de supports cellulaires ou de filtres. Mots-cles : melanges immiscibles, acide polylactique, amidon thermoplastique, morphologie cocontinue, lixiviation selective, microtomographie R-X, materiau rigide poreux biodegradable.

Solid state phase change materials for thermal energy storage in passive solar heated buildings

NASA Astrophysics Data System (ADS)

Benson, D. K.; Christensen, C.

1983-11-01

A set of solid state phase change materials was evaluated for possible use in passive solar thermal energy storage systems. The most promising materials are organic solid solutions of pentaerythritol, pentaglycerine and neopentyl glycol. Solid solution mixtures of these compounds can be tailored so that they exhibit solid-to-solid phase transformations at any desired temperature within the range from less than 25 deg to 188 deg. Thermophysical properties such as thermal conductivity, density and volumetric expansion were measured. Computer simulations were used to predict the performance of various Trombe wall designs incorporating solid state phase change materials. Optimum performance was found to be sensitive to the choice of phase change temperatures and to the thermal conductivity of the phase change material. A molecular mechanism of the solid state phase transition is proposed and supported by infrared spectroscopic evidence.

Experimental Plan for Crystal Accumulation Studies in the WTP Melter Riser

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, D.; Fowley, M.

2015-04-28

This experimental plan defines crystal settling experiments to be in support of the U.S. Department of Energy – Office of River Protection crystal tolerant glass program. The road map for development of crystal-tolerant high level waste glasses recommends that fluid dynamic modeling be used to better understand the accumulation of crystals in the melter riser and mechanisms of removal. A full-scale version of the Hanford Waste Treatment and Immobilization Plant (WTP) melter riser constructed with transparent material will be used to provide data in support of model development. The system will also provide a platform to demonstrate mitigation or recoverymore » strategies in off-normal events where crystal accumulation impedes melter operation. Test conditions and material properties will be chosen to provide results over a variety of parameters, which can be used to guide validation experiments with the Research Scale Melter at the Pacific Northwest National Laboratory, and that will ultimately lead to the development of a process control strategy for the full scale WTP melter. The experiments described in this plan are divided into two phases. Bench scale tests will be used in Phase 1 (using the appropriate solid and fluid simulants to represent molten glass and spinel crystals) to verify the detection methods and analytical measurements prior to their use in a larger scale system. In Phase 2, a full scale, room temperature mockup of the WTP melter riser will be fabricated. The mockup will provide dynamic measurements of flow conditions, including resistance to pouring, as well as allow visual observation of crystal accumulation behavior.« less

A Research Agenda for Scientific and Technical Information Held in Lisbon, Portugal on 7-9 April 1992 (Un Programme de Recherche pour l’Information Scientifique et Technique).

DTIC Science & Technology

1992-11-01

field of inquiry. Good solid research advances fault library science and information science for not ask- the state of the art by contributing to the...further research and application. Ennis (1967) problems faced each day by practitioners. Robert Smith commented that library science research is...under ogy, and technical communications. Library science the title "On Information Science." Keren raises interest- and information science have been

Bimanes and Related Heterocycles as Laser Dyes

DTIC Science & Technology

1991-01-10

the bimane 19 as a yel- was acidified (dilute hydrochloric acid ) to precipi- low crystalline solid, 0.22 g (25%), mp 214-215°C, tate a trace amount...treatment 2,6-diethyl (PMDEP-BF2), and 2,6-disulfonic acid of a pyrromethene with boron trifluoride . Charac- (isolated as the disodium salt PMPDS-BF2... Chlorine was obtained acid (85%, 320 mL). The mixture was heated at from Matheson Gas Products, Secaccus, NJ. Nitro- 180°C for 30 min and poured into aqueous

CFD Techniques for Propulsion Applications Panel Symposium (77th), Held in San Antonio, Texas on 27-31 May 1991 (Les Techniques de l’Aerodynamique Numerique pour les Applications aux Propulseurs)

DTIC Science & Technology

1992-02-01

CONCLUDING REMARKS secondary flow pattern. Probably both factors are influential. Unfortunately The present study has examined the the secondary...Panels which are compesed of experts appointed - by the National Delegates, the Consultant and Exchange Programme and the Aerospace Applications Studies ...CP 352. September 1983 /Combustion Problems in Turbine Engines AGARD CP 353, January 1984 (,rHazard Studies for Solid Propellant Rocket Motors AGARD CP

40 CFR 227.32 - Liquid, suspended particulate, and solid phases of a material.

Code of Federal Regulations, 2010 CFR

2010-07-01

... solid phases of a material. 227.32 Section 227.32 Protection of Environment ENVIRONMENTAL PROTECTION... MATERIALS Definitions § 227.32 Liquid, suspended particulate, and solid phases of a material. (a) For the... obtained above prior to centrifugation and filtration. The solid phase includes all material settling to...

40 CFR 227.32 - Liquid, suspended particulate, and solid phases of a material.

Code of Federal Regulations, 2011 CFR

2011-07-01

... solid phases of a material. 227.32 Section 227.32 Protection of Environment ENVIRONMENTAL PROTECTION... MATERIALS Definitions § 227.32 Liquid, suspended particulate, and solid phases of a material. (a) For the... obtained above prior to centrifugation and filtration. The solid phase includes all material settling to...

Biological treatment of soils contaminated with hydrophobic organics using slurry- and solid-phase techniques

NASA Astrophysics Data System (ADS)

Cassidy, Daniel H.; Irvine, Robert L.

1995-10-01

Both slurry-phase and solid-phase bioremediation are effective ex situ soil decontamination methods. Slurrying is energy intensive relative to solid-phase treatment, but provides homogenization and uniform nutrient distribution. Limited contaminant bioavailability at concentrations above the required cleanup level reduces biodegradation rates and renders solid phase bioremediation more cost effective than complete treatment in a bio-slurry reactor. Slurrying followed by solid-phase bioremediation combines the advantages and minimizes the weaknesses of each treatment method when used alone. A biological treatment system consisting of slurrying followed by aeration in solid phase bioreactors was developed and tested in the laboratory using a silty clay loam contaminated with diesel fuel. The first set of experiments was designed to determine the impact of the water content and mixing time during slurrying on the rate an extent of contaminant removal in continuously aerated solid phase bioreactors. The second set of experiments compared the volatile and total diesel fuel removal in solid phase bioreactors using periodic and continuous aeration strategies. Results showed that slurrying for 1.5 hours at a water content less than saturation markedly increased the rate and extent of contaminant biodegradation in the solid phase bioreactors compared with soil having no slurry pretreatment. Slurrying the soil at or above its saturation moisture content resulted in lengthy dewatering times which prohibited aeration, thereby delaying the onset of biological treatment in the solid phase bioreactors. Results also showed that properly operated periodic aeration can provide less volatile contaminant removal and a grater fraction of biological contaminant removal than continuous aeration.

Caracterisation des melanges developpes pour le moulage basse pression des poudres metalliques (LPIM) =

NASA Astrophysics Data System (ADS)

Fareh, Fouad

Le moulage par injection basse pression des poudres metalliques est une technique de fabrication qui permet de fabriquer des pieces possedant la complexite des pieces coulees mais avec les proprietes mecaniques des pieces corroyees. Cependant, l'optimisation des etapes de deliantage et de frittage a ete jusqu'a maintenant effectuee a l'aide de melange pour lesquels la moulabilite optimale n'a pas encore ete demontree. Ainsi, la comprehension des proprietes rheologiques et de la segregation des melanges est tres limitee et cela presente le point faible du processus de LPIM. L'objectif de ce projet de recherche etait de caracteriser l'influence des liants sur le comportement rheologique des melanges en mesurant la viscosite et la segregation des melanges faible viscosite utilises dans le procede LPIM. Afin d'atteindre cet objectif, des essais rheologiques et thermogravimetriques ont ete conduits sur 12 melanges. Ces melanges ont ete prepares a base de poudre d'Inconel 718 de forme spherique (chargement solide constant a 60%) et de cires, d'agents surfactants ou epaississants. Les essais rheologiques ont ete utilises entre autre pour calculer l'indice d'injectabilite ?STV des melanges, tandis que les essais thermogravimetriques ont permis d'evaluer precisement la segregation des poudres dans les melanges. Il a ete demontre que les trois (3) melanges contenant de la cire de paraffine et de l'acide stearique presentent des indices alpha STV plus eleves qui sont avantageux pour le moulage par injection des poudres metalliques (MIM), mais segregent beaucoup trop pour que la piece fabriquee produise de bonnes caracteristiques mecaniques. A l'oppose, le melange contenant de la cire de paraffine et de l'ethylene-vinyle acetate ainsi que le melange contenant seulement de la cire de carnauba segregent peu voire pas du tout, mais possedent de tres faibles indices alphaSTV : ils sont donc difficilement injectables. Le meilleur compromis semble donc etre les melanges contenant de la cire (de paraffine, d'abeille et de carnauba) et de faible teneur en acide stearique et en ethylene-vinyle acetate. Par ailleurs, les lois physiques preexistantes ont permis de confirmer les resultats des essais rheologiques et thermogravimetriques, mais aussi de mettre en evidence l'influence de la segregation sur les proprietes rheologiques des melanges. Ces essais ont aussi montre l'effet de constituants de liant et du temps passe a l'etat fondu sur l'intensite de la segregation dans les melanges. Les melanges contenants de l'acide stearique segregent rapidement. La caracterisation des melanges developpes pour le moulage basse pression des poudres metalliques doit etre obtenue a l'aide d'une methode de courte duree pour eviter la segregation et de mesurer precisement l'aptitude a l'ecoulement de ces melanges.

Literacy and Health Project. Phase One. Making the World Healthier and Safer for People Who Can't Read = Projet alphabetisation et sante: Premiere etape. Rendre le milieu plus sain et sans danger pour les personnes qui ne savent pas lire.

ERIC Educational Resources Information Center

Ontario Public Health Association, Toronto.

The Literacy and Health Project was set up to determine how reading and health problems were connected. A research phase documented the relationship between literacy and health. Information was collected from community organizations, literature review, three case studies in Ontario, and key informant interviews. The consultation process involved…

Seasonal multiphase equilibria in the atmospheres of Titan and Pluto

NASA Astrophysics Data System (ADS)

Tan, S. P.; Kargel, J. S.

2017-12-01

At the extremely low temperatures in Titan's upper troposphere and on Pluto's surface, the atmospheres as a whole are subject to freeze into solid solutions, not pure ices. The presence of the solid phases introduces conditions with rich phase equilibria upon seasonal changes, even if the temperature undergoes only small changes. For the first time, the profile of atmospheric methane in Titan's troposphere will be reproduced complete with the solid solutions. This means that the freezing point, i.e. the altitude where the first solid phase appears, is determined. The seasonal change will also be evaluated both at the equator and the northern polar region. For Pluto, also for the first time, the seasonal solid-vapor equilibria will be evaluated. The fate of the two solid phases, the methane-rich and carbon-monoxide-rich solid solutions, will be analyzed upon temperature and pressure changes. Such investigations are enabled by the development of a molecular-based thermodynamic model for cryogenic chemical systems, referred to as CRYOCHEM, which includes solid solutions in its phase-equilibria calculations. The atmospheres of Titan and Pluto are modeled as ternary gas mixtures: nitrogen-methane-ethane and nitrogen-methane-carbon monoxide, respectively. Calculations using CRYOCHEM can provide us with compositions not only in two-phase equilibria, but also that in three-phase equilibria. Densities of all phases involved will also be calculated. For Titan, density inversion between liquid and solid phases will be identified and presented. In the inversion, the density of solid phase is less than that in the liquid phase. The method and results of this work will be useful for further investigations and modeling on the atmospheres of Titan, Pluto, and other bodies with similar conditions in the Solar System and beyond.

Materials research for passive solar systems: Solid-state phase-change materials

NASA Astrophysics Data System (ADS)

Benson, D. K.; Webb, J. D.; Burrows, R. W.; McFadden, J. D. O.; Christensen, C.

1985-03-01

A set of solid-state phase-change materials is being evaluated for possible use in passive solar thermal energy storage systems. The most promising materials are organic solid solutions of pentaerythritol (C5H12O4), pentaglycerinve (C5H12O3), and neopentyl glycol (C5H12O2). Solid solution mixtures of these compounds can be tailored so that they exhibit solid-to-solid phase transformations at any desired temperature between 25 C and 188 C, and have latent heats of transformation etween 20 and 70 cal/g. Transformation temperatures, specific heats, and latent heats of transformation have been measured for a number of these materials. Limited cyclic experiments suggest that the solid solutions are stable. These phase-change materials exhibit large amounts of undercooling; however, the addition of certain nucleating agents as particulate dispersions in the solid phase-change material greatly reduces this effect. Computer simulations suggest that the use of an optimized solid-state phase-change material in a Trombe wall could provide better performance than a concrete Trombe wall four times thicker and nine times heavier.

Microstructural characterization of as-cast biocompatible Co-Cr-Mo alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giacchi, J.V., E-mail: jgiacchi@exa.unicen.edu.ar; Instituto de Fisica de Materiales Tandil; Morando, C.N.

2011-01-15

The microstructure of a cobalt-base alloy (Co-Cr-Mo) obtained by the investment casting process was studied. This alloy complies with the ASTM F75 standard and is widely used in the manufacturing of orthopedic implants because of its high strength, good corrosion resistance and excellent biocompatibility properties. This work focuses on the resulting microstructures arising from samples poured under industrial environment conditions, of three different Co-Cr-Mo alloys. For this purpose, we used: 1) an alloy built up from commercial purity constituents, 2) a remelted alloy and 3) a certified alloy for comparison. The characterization of the samples was achieved by using opticalmore » microscopy (OM) with a colorant etchant to identify the present phases and scanning electron microscopy (SE-SEM) and energy dispersion spectrometry (EDS) techniques for a better identification. In general the as-cast microstructure is a Co-fcc dendritic matrix with the presence of a secondary phase, such as the M{sub 23}C{sub 6} carbides precipitated at grain boundaries and interdendritic zones. These precipitates are the main strengthening mechanism in this type of alloys. Other minority phases were also reported and their presence could be linked to the cooling rate and the manufacturing process variables and environment. - Research Highlights: {yields}The solidification microstructure of an ASTM-F75 type alloy were studied. {yields}The alloys were poured under an industrial environment. {yields}Carbides and sigma phase identified by color metallography and scanning microscopy (SEM and EDS). {yields}Two carbide morphologies were detected 'blocky type' and 'pearlite type'. {yields}Minority phases were also detected.« less

Benzocaine polymorphism: pressure-temperature phase diagram involving forms II and III.

PubMed

Gana, Inès; Barrio, Maria; Do, Bernard; Tamarit, Josep-Lluís; Céolin, René; Rietveld, Ivo B

2013-11-18

Understanding the phase behavior of an active pharmaceutical ingredient in a drug formulation is required to avoid the occurrence of sudden phase changes resulting in decrease of bioavailability in a marketed product. Benzocaine is known to possess three crystalline polymorphs, but their stability hierarchy has so far not been determined. A topological method and direct calorimetric measurements under pressure have been used to construct the topological pressure-temperature diagram of the phase relationships between the solid phases II and III, the liquid, and the vapor phase. In the process, the transition temperature between solid phases III and II and its enthalpy change have been determined. Solid phase II, which has the highest melting point, is the more stable phase under ambient conditions in this phase diagram. Surprisingly, solid phase I has not been observed during the study, even though the scarce literature data on its thermal behavior appear to indicate that it might be the most stable one of the three solid phases. Copyright © 2013 Elsevier B.V. All rights reserved.

The global phase diagram of the Gay-Berne model

NASA Astrophysics Data System (ADS)

de Miguel, Enrique; Vega, Carlos

2002-10-01

The phase diagram of the Gay-Berne model with anisotropy parameters κ=3, κ'=5 has been evaluated by means of computer simulations. For a number of temperatures, NPT simulations were performed for the solid phase leading to the determination of the free energy of the solid at a reference density. Using the equation of state and free energies of the isotropic and nematic phases available in the existing literature the fluid-solid equilibrium was calculated for the temperatures selected. Taking these fluid-solid equilibrium results as the starting points, the fluid-solid equilibrium curve was determined for a wide range of temperatures using Gibbs-Duhem integration. At high temperatures the sequence of phases encountered on compression is isotropic to nematic, and then nematic to solid. For reduced temperatures below T=0.85 the sequence is from the isotropic phase directly to the solid state. In view of this we locate the isotropic-nematic-solid triple point at TINS=0.85. The present results suggest that the high-density phase designated smectic B in previous simulations of the model is in fact a molecular solid and not a smectic liquid crystal. It seems that no thermodynamically stable smectic phase appears for the Gay-Berne model with the choice of parameters used in this work. We locate the vapor-isotropic liquid-solid triple point at a temperature TVIS=0.445. Considering that the critical temperatures is Tc=0.473, the Gay-Berne model used in this work presents vapor-liquid separation over a rather narrow range of temperatures. It is suggested that the strong lateral attractive interactions present in the Gay-Berne model stabilizes the layers found in the solid phase. The large stability of the solid phase, particularly at low temperatures, would explain the unexpectedly small liquid range observed in the vapor-liquid region.

Sandwich-type electrode

DOEpatents

Lu, Wen-Tong P.; Garcia, Earl R.

1983-01-01

Disclosed is an improvement on a method of making an electrode wherein a suspension in a liquid is prepared of a powdered catalyst containing a noble metal, carbon powder and a binder, and the suspension is poured over a carbon substrate dried, compressed and sintered to form a solid catalyst layer bonded to the carbon substrate. The improvement is placing a carbon paper on the catalyst layer prior to compressing. The improved electrode can be used as either a cathode or an anode in a sulfur dioxide depolarized electrolyzer in a process for producing hydrogen from water.

The concrete technology of post pouring zone of raft foundation of Hongyun Building B tower

NASA Astrophysics Data System (ADS)

Yin, Suhua; Yu, Liu; Wu, Yanli; Zhao, Ying

2017-08-01

The foundation of Hongyun building B tower is made of raft board foundation which is 3300mm in the thickness concreted pouring amount of large and the late poured band in the pouring settlement formed. The temperature of the pouring settlement was controlled in order to prevent the crack of the construction of the late poured band. The steel of post pouring band was designed and monitorred. The quality of post pouring band quality is guaranteed in the raft concrete foundation of Hongyun Building B tower.

Precipitation in Al–Mg solid solution prepared by solidification under high pressure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jie, J.C., E-mail: jiejc@dlut.edu.cn; School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001; Wang, H.W.

2014-01-15

The precipitation in Al–Mg solid solution containing 21.6 at.% Mg prepared by solidification under 2 GPa was investigated. The results show that the γ-Al{sub 12}Mg{sub 17} phase is formed and the β′ phase cannot be observed in the solid solution during ageing process. The precipitation of γ and β phases takes place in a non-uniform manner during heating process, i.e. the γ and β phases are first formed in the interdendritic region, which is caused by the inhomogeneous distribution of Mg atoms in the solid solution solidified under high pressure. Peak splitting of X-ray diffraction patterns of Al(Mg) solid solutionmore » appears, and then disappears when the samples are aged at 423 K for different times, due to the non-uniform precipitation in Al–Mg solid solution. The direct transformation from the γ to β phase is observed after ageing at 423 K for 24 h. It is considered that the β phase is formed through a peritectoid reaction of α + γ → β which needs the diffusion of Mg atoms across the interface of α/γ phases. - Highlights: • The γ phase is formed and the β′ phase is be observed in Al(Mg) solid solution. • Peak splitting of XRD pattern of Al(Mg) solid solution appears during aged at 150 °C. • The β phase is formed through a peritectoid reaction of α + γ → β.« less

Big drinkers: how BMI, gender and rules of thumb influence the free pouring of wine.

PubMed

Smarandescu, Laura; Walker, Doug; Wansink, Brian

2014-11-01

This research examines free pouring behavior and provides an account of how Body Mass Index (BMI) and gender might lead to the overpouring, and consequently the overconsumption of wine. An observational study with young adults investigated how BMI and gender affect free-pouring of wine over a variety of pouring scenarios, and how rules-of-thumb in pouring affect the quantities of alcohol poured by men and women across BMI categories. For men, the amount poured was positively related to BMI. However, BMI did not affect pours by women. The use of the "half glass" rule-of-thumb in pouring reduced the volume of wine poured by over 20% for both men and women. Importantly, this rule-of-thumb substantially attenuated the pours by men at high BMI levels. Increasing awareness of pouring biases represents an early and effective step toward curbing alcohol consumption among men, and especially those who are overweight. Additionally, using a simple "half glass" rule-of-thumb may be an effective way to curb overpouring, despite non-standard glass sizes. Copyright © 2014. Published by Elsevier B.V.

Simulation d'ecoulements internes compressibles laminaires et turbulents par une methode d'elements finis

NASA Astrophysics Data System (ADS)

Rebaine, Ali

1997-08-01

Ce travail consiste en la simulation numerique des ecoulements internes compressibles bidimensionnels laminaires et turbulents. On s'interesse, particulierement, aux ecoulements dans les ejecteurs supersoniques. Les equations de Navier-Stokes sont formulees sous forme conservative et utilisent, comme variables independantes, les variables dites enthalpiques a savoir: la pression statique, la quantite de mouvement et l'enthalpie totale specifique. Une formulation variationnelle stable des equations de Navier-Stokes est utilisee. Elle est base sur la methode SUPG (Streamline Upwinding Petrov Galerkin) et utilise un operateur de capture des forts gradients. Un modele de turbulence, pour la simulation des ecoulements dans les ejecteurs, est mis au point. Il consiste a separer deux regions distinctes: une region proche de la paroi solide, ou le modele de Baldwin et Lomax est utilise et l'autre, loin de la paroi, ou une formulation nouvelle, basee sur le modele de Schlichting pour les jets, est proposee. Une technique de calcul de la viscosite turbulente, sur un maillage non structure, est implementee. La discretisation dans l'espace de la forme variationnelle est faite a l'aide de la methode des elements finis en utilisant une approximation mixte: quadratique pour les composantes de la quantite de mouvement et de la vitesse et lineaire pour le reste des variables. La discretisation temporelle est effectuee par une methode de differences finies en utilisant le schema d'Euler implicite. Le systeme matriciel, resultant de la discretisation spatio-temporelle, est resolu a l'aide de l'algorithme GMRES en utilisant un preconditionneur diagonal. Les validations numeriques ont ete menees sur plusieurs types de tuyeres et ejecteurs. La principale validation consiste en la simulation de l'ecoulement dans l'ejecteur teste au centre de recherche NASA Lewis. Les resultats obtenus sont tres comparables avec ceux des travaux anterieurs et sont nettement superieurs concernant les ecoulements turbulents dans les ejecteurs.

Scalability, Scintillation Readout and Charge Drift in a Kilogram Scale Solid Xenon Particle Detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoo, J.; Cease, H.; Jaskierny, W. F.

2014-10-23

We report a demonstration of the scalability of optically transparent xenon in the solid phase for use as a particle detector above a kilogram scale. We employ a liquid nitrogen cooled cryostat combined with a xenon purification and chiller system to measure the scintillation light output and electron drift speed from both the solid and liquid phases of xenon. Scintillation light output from sealed radioactive sources is measured by a set of high quantum efficiency photomultiplier tubes suitable for cryogenic applications. We observed a reduced amount of photons in solid phase compared to that in liquid phase. We used amore » conventional time projection chamber system to measure the electron drift time in a kilogram of solid xenon and observed faster electron drift speed in the solid phase xenon compared to that in the liquid phase.« less

Fuel spill identification using solid-phase extraction and solid-phase microextraction. 1. Aviation turbine fuels.

PubMed

Lavine, B K; Brzozowski, D M; Ritter, J; Moores, A J; Mayfield, H T

2001-12-01

The water-soluble fraction of aviation jet fuels is examined using solid-phase extraction and solid-phase microextraction. Gas chromatographic profiles of solid-phase extracts and solid-phase microextracts of the water-soluble fraction of kerosene- and nonkerosene-based jet fuels reveal that each jet fuel possesses a unique profile. Pattern recognition analysis reveals fingerprint patterns within the data characteristic of fuel type. By using a novel genetic algorithm (GA) that emulates human pattern recognition through machine learning, it is possible to identify features characteristic of the chromatographic profile of each fuel class. The pattern recognition GA identifies a set of features that optimize the separation of the fuel classes in a plot of the two largest principal components of the data. Because principal components maximize variance, the bulk of the information encoded by the selected features is primarily about the differences between the fuel classes.

Solid-solid phase change thermal storage application to space-suit battery pack

NASA Astrophysics Data System (ADS)

Son, Chang H.; Morehouse, Jeffrey H.

1989-01-01

High cell temperatures are seen as the primary safety problem in the Li-BCX space battery. The exothermic heat from the chemical reactions could raise the temperature of the lithium electrode above the melting temperature. Also, high temperature causes the cell efficiency to decrease. Solid-solid phase-change materials were used as a thermal storage medium to lower this battery cell temperature by utilizing their phase-change (latent heat storage) characteristics. Solid-solid phase-change materials focused on in this study are neopentyl glycol and pentaglycerine. Because of their favorable phase-change characteristics, these materials appear appropriate for space-suit battery pack use. The results of testing various materials are reported as thermophysical property values, and the space-suit battery operating temperature is discussed in terms of these property results.

Energy and Resource Saving of Steelmaking Process: Utilization of Innovative Multi-phase Flux During Dephosphorization Process

NASA Astrophysics Data System (ADS)

Matsuura, Hiroyuki; Hamano, Tasuku; Zhong, Ming; Gao, Xu; Yang, Xiao; Tsukihashi, Fumitaka

2014-09-01

An increase in the utilization efficiency of CaO, one of the major fluxing agents used in various steelmaking processes, is required to reduce the amount of discharged slag and energy consumption of the process. The authors have intensively focused on the development of innovative dephosphorization process by using so called "multi-phase flux" composed of solid and liquid phases. This article summarizes the research on the above topic done by the authors, in which the formation mechanisms of P2O5-containing phase during CaO or 2CaO·SiO2 dissolution into molten slag, the phase relationship between solid and liquid phases at equilibrium, and thermodynamic properties of P2O5-containing phase have been clarified. The reactions between solid CaO or 2CaO·SiO2 and molten CaO-FeO x -SiO2-P2O5 slag were observed by dipping solid specimen in the synthesized slag at 1573 K or 1673 K. The formation of the CaO-FeO layer and dual-phase layer of solid 2CaO·SiO2 and FeO x -rich liquid phase was observed around the interface from the solid CaO side toward the bulk slag phase side. Condensation of P2O5 into 2CaO·SiO2 phase as 2CaO·SiO2-3CaO·P2O5 solid solution was observed in both cases of CaO and 2CaO·SiO2 as solid specimens. Measurement of the phase relationship for the CaO-FeO x -SiO2-P2O5 system confirmed the condensation of P2O5 in solid phase at low oxygen partial pressure. The thermodynamics of 2CaO·SiO2-3CaO·P2O5 solid solution are to be clarified to quantitatively simulate the dephosphorization process, and the current results are also introduced. Based on the above results, the reduction of CaO consumption, the discharged slag curtailment, and energy-saving effects have been discussed.

Counter-IED Initiative PPE Horizon 0, Phase 1, Protection Versus Performance Preliminary Trade-off Analysis, Behavioural Task Analysis (Initiative d’epi pour la Lutte aux IED - Horizon 0 Phase 1 - Analyse de Compromis Preliminaire de la Protection par Rapport au Rendement Analyse Comportementale des Taches)

DTIC Science & Technology

2007-05-01

RESULTS .............................................................................92 TABLE 17: RATINGS OF THE THERMAL COMFORT ON A 7 POINT SCALE...98. In addition to the body mapping of thermal discomfort, participants also rated thermal comfort acceptability for hot spots, ventilation and...overall comfort. Additionally each participant completed a thermal comfort Humansystems® Counter IED Page 91 questionnaire that examined ventilation

Crystallization process

DOEpatents

Adler, Robert J.; Brown, William R.; Auyang, Lun; Liu, Yin-Chang; Cook, W. Jeffrey

1986-01-01

An improved crystallization process is disclosed for separating a crystallizable material and an excluded material which is at least partially excluded from the solid phase of the crystallizable material obtained upon freezing a liquid phase of the materials. The solid phase is more dense than the liquid phase, and it is separated therefrom by relative movement with the formation of a packed bed of solid phase. The packed bed is continuously formed adjacent its lower end and passed from the liquid phase into a countercurrent flow of backwash liquid. The packed bed extends through the level of the backwash liquid to provide a drained bed of solid phase adjacent its upper end which is melted by a condensing vapor.

Qualité des eaux de la station de traitement de la ville de Skikda, Algérie Essais d'optimisation de la clarification

NASA Astrophysics Data System (ADS)

Meghzili, B.; Medjram, M. S.; Achour, S.

2005-05-01

A cause de la sécheresse qui a sévit durant une décennie, la station de traitement de l'eau potable de la ville de Skikda Algérie, en vue de combler le déficit en eau, utilise un mélange des eaux de surface (barrage) et des eaux souterraines (forage). Les résultats des analyses physico-chimiques de ces eaux montrent la présence de micropolluants, notamment le mercure, avec une concentration de 0.035 mg/l pour les eaux de surface et une concentration de 0.02 mg/l pour les eaux souterraines. Ces résultats obtenus, montrent également que la concentration en matières organiques dépasse, pour les deux sources, les normes OMS. Afin de réduire les effets de cette pollution, nous avons calculé les doses nécessaires des différents réactifs utilisés sur la base des essais d'optimisation réalisés en laboratoire. Les résultats obtenus nous ont permis de conclure que les doses de 30 à 60 mg/l de sulfate d'aluminium (S.A) sont nécessaires à une bonne élimination de la turbidité et des matières organiques (M.O) et que l'utilisation du charbon active en poudre (C.A.P) permet la réduction de la teneur en mercure au dessous du seuil admissible. L'utilisation d'un adjuvant (chaux vive) permet d'améliorer les résultats surtout pour la turbidité (4 mg/l). Une préchloration au break point semble intéressante pour améliorer la phase de floculation.

Effets des electrons secondaires sur l'ADN

NASA Astrophysics Data System (ADS)

Boudaiffa, Badia

Les interactions des electrons de basse energie (EBE) representent un element important en sciences des radiations, particulierement, les sequences se produisant immediatement apres l'interaction de la radiation ionisante avec le milieu biologique. Il est bien connu que lorsque ces radiations deposent leur energie dans la cellule, elles produisent un grand nombre d'electrons secondaires (4 x 104/MeV), qui sont crees le long de la trace avec des energies cinetiques initiales bien inferieures a 20 eV. Cependant, il n'y a jamais eu de mesures directes demontrant l'interaction de ces electrons de tres basse energie avec l'ADN, du principalement aux difficultes experimentales imposees par la complexite du milieu biologique. Dans notre laboratoire, les dernieres annees ont ete consacrees a l'etude des phenomenes fondamentaux induits par impact des EBE sur differentes molecules simples (e.g., N2, CO, O2, H2O, NO, C2H 4, C6H6, C2H12) et quelques molecules complexes dans leur phase solide. D'autres travaux effectues recemment sur des bases de l'ADN et des oligonucleotides ont montre que les EBE produisent des bris moleculaires sur les biomolecules. Ces travaux nous ont permis d'elaborer des techniques pour mettre en evidence et comprendre les interactions fondamentales des EBE avec des molecules d'interet biologique, afin d'atteindre notre objectif majeur d'etudier l'effet direct de ces particules sur la molecule d'ADN. Les techniques de sciences des surfaces developpees et utilisees dans les etudes precitees peuvent etre etendues et combinees avec des methodes classiques de biologie pour etudier les dommages de l'ADN induits par l'impact des EBE. Nos experiences ont montre l'efficacite des electrons de 3--20 eV a induire des coupures simple et double brins dans l'ADN. Pour des energies inferieures a 15 eV, ces coupures sont induites par la localisation temporaire d'un electron sur une unite moleculaire de l'ADN, ce qui engendre la formation d'un ion negatif transitoire dans un etat electronique dissociatif, cette localisation est suivie d'une fragmentation. A plus haute energie, la dissociation dipolaire (i.e., la formation simultanee d'un ion positif et negatif) et l'ionisation jouent un role important dans le dommage de l'ADN. L'ensemble de nos resultats permet d'expliquer les mecanismes de degradation de l'ADN par les EBE et d'obtenir des sections efficaces effectives des differents types de dommages.

Dramatically different kinetics and mechanism at solid/liquid and solid/gas interfaces for catalytic isopropanol oxidation over size-controlled platinum nanoparticles.

PubMed

Wang, Hailiang; Sapi, Andras; Thompson, Christopher M; Liu, Fudong; Zherebetskyy, Danylo; Krier, James M; Carl, Lindsay M; Cai, Xiaojun; Wang, Lin-Wang; Somorjai, Gabor A

2014-07-23

We synthesize platinum nanoparticles with controlled average sizes of 2, 4, 6, and 8 nm and use them as model catalysts to study isopropanol oxidation to acetone in both the liquid and gas phases at 60 °C. The reaction at the solid/liquid interface is 2 orders of magnitude slower than that at the solid/gas interface, while catalytic activity increases with the size of platinum nanoparticles for both the liquid-phase and gas-phase reactions. The activation energy of the gas-phase reaction decreases with the platinum nanoparticle size and is in general much higher than that of the liquid-phase reaction which is largely insensitive to the size of catalyst nanoparticles. Water substantially promotes isopropanol oxidation in the liquid phase. However, it inhibits the reaction in the gas phase. The kinetic results suggest different mechanisms between the liquid-phase and gas-phase reactions, correlating well with different orientations of IPA species at the solid/liquid interface vs the solid/gas interface as probed by sum frequency generation vibrational spectroscopy under reaction conditions and simulated by computational calculations.

Solidification and solid-state transformation sciences in metals additive manufacturing

DOE PAGES

Kirka, Michael M.; Nandwana, Peeyush; Lee, Yousub; ...

2017-02-11

Additive manufacturing (AM) of metals is rapidly emerging as an established manufacturing process for metal components. Unlike traditional metals fabrication processes, metals fabricated via AM undergo localized thermal cycles during fabrication. As a result, AM presents the opportunity to control the liquid-solid phase transformation, i.e. material texture. But, thermal cycling presents challenges from the standpoint of solid-solid phase transformations. We will discuss the opportunities and challenges in metals AM in the context of texture control and associated solid-solid phase transformations in Ti-6Al-4V and Inconel 718.

Caracterisation des proprietes dielectriques de materiaux composites a base de polyethylene terephtalate recycle =

NASA Astrophysics Data System (ADS)

Mebarki, Fouzia

Cette etude vise a etudier la possibilite d'utiliser des materiaux composites a matrice thermoplastique pour des applications electriques comme les supports des systemes d'allumage dans les moteurs d'automobile. Nous nous interessons plus particulierement aux composites a base de polyethylene terephtalate (PET) recycle. Les isolants classiques comme le PET ne peuvent pas satisfaire toutes les exigences. L'introduction des renforts comme les fibres de verre et le mica peuvent ameliorer les caracteristiques mecaniques de ces materiaux. Toutefois, cette amelioration peut etre accompagnee d'une diminution des proprietes electriques surtout que ces materiaux doivent operer sous contraintes thermiques et electriques tres severes. Afin d'estimer la duree de vie de ces isolants, des essais de vieillissement accelere ont ete effectues a une frequence de 300Hz dans une plage de temperature allant de la temperature ambiante a 140°C. L'etude a haute temperature permettra de determiner la temperature de service des materiaux candidats. Des essais de la rupture dielectrique ont ete realises sur un grand nombre d'echantillon selon la norme ASTM D-149 relative aux mesures de rigidite dielectrique des isolants solides. Ces tests ont permis de deceler les echantillons problematiques et de verifier la qualite de ces isolants solides. Les differentes connaissances acquises lors de cette analyse ont servi a predire les performances des materiaux en service et vont permettre a la compagnie Groupe Lavergne d'apporter des ameliorations au niveau des formulations existantes et par la suite developper un materiau ayant les proprietes electriques et thermiques adequates pour ce type d'application. None None None None

Microwave spectroscopic observation of distinct electron solid phases in wide quantum wells

NASA Astrophysics Data System (ADS)

Hatke, A. T.; Liu, Yang; Magill, B. A.; Moon, B. H.; Engel, L. W.; Shayegan, M.; Pfeiffer, L. N.; West, K. W.; Baldwin, K. W.

2014-06-01

In high magnetic fields, two-dimensional electron systems can form a number of phases in which interelectron repulsion plays the central role, since the kinetic energy is frozen out by Landau quantization. These phases include the well-known liquids of the fractional quantum Hall effect, as well as solid phases with broken spatial symmetry and crystalline order. Solids can occur at the low Landau-filling termination of the fractional quantum Hall effect series but also within integer quantum Hall effects. Here we present microwave spectroscopy studies of wide quantum wells that clearly reveal two distinct solid phases, hidden within what in d.c. transport would be the zero diagonal conductivity of an integer quantum-Hall-effect state. Explanation of these solids is not possible with the simple picture of a Wigner solid of ordinary (quasi) electrons or holes.

Extinguishment of a Diffusion Flame Over a PMMA Cylinder by Depressurization in Reduced-Gravity

NASA Technical Reports Server (NTRS)

Goldmeer, Jeffrey Scott

1996-01-01

Extinction of a diffusion flame burning over horizontal PMMA (Polymethyl methacrylate) cylinders in low-gravity was examined experimentally and via numerical simulations. Low-gravity conditions were obtained using the NASA Lewis Research Center's reduced-gravity aircraft. The effects of velocity and pressure on the visible flame were examined. The flammability of the burning solid was examined as a function of pressure and the solid-phase centerline temperature. As the solid temperature increased, the extinction pressure decreased, and with a centerline temperature of 525 K, the flame was sustained to 0.1 atmospheres before extinguishing. The numerical simulation iteratively coupled a two-dimensional quasi-steady, gas-phase model with a transient solid-phase model which included conductive heat transfer and surface regression. This model employed an energy balance at the gas/solid interface that included the energy conducted by the gas-phase to the gas/solid interface, Arrhenius pyrolysis kinetics, surface radiation, and the energy conducted into the solid. The ratio of the solid and gas-phase conductive fluxes Phi was a boundary condition for the gas-phase model at the solid-surface. Initial simulations modeled conditions similar to the low-gravity experiments and predicted low-pressure extinction limits consistent with the experimental limits. Other simulations examined the effects of velocity, depressurization rate and Phi on extinction.

Utilisation de la mélatonine pour le sommeil chez les enfants en bonne santé

PubMed Central

Janjua, Irvin; Goldman, Ran D.

2016-01-01

Résumé Question Une maman a amené son garçon de 12 ans me consulter à mon bureau. Elle s’inquiète, car il a de la difficulté à s’endormir presque tous les soirs. Elle travaille par quarts et elle prend elle-même de la mélatonine pour l’aider à s’endormir. Elle m’a demandé si son garçon pouvait aussi prendre de la mélatonine. Quels sont les recommandations et les éléments à considérer avant d’utiliser la mélatonine chez les enfants et les adolescents en bonne santé? Réponse L’insomnie est rapportée chez jusqu’à un quart des enfants en bonne santé et chez les trois quarts des enfants atteints d’une affection psychiatrique ou neurodéveloppementale, ce qui entraîne des conséquences négatives. Pour les enfants atteints du syndrome de retard de phase du sommeil, la mélatonine pourrait s’avérer utile lorsque jumelée à une évaluation de l’insomnie et à un suivi régulier. La mélatonine pourrait être envisagée pour des enfants sans diagnostic d’insomnie qui ont une bonne hygiène du sommeil. Bien qu’elle semble sans danger, il n’existe pas de données probantes en faveur de l’emploi systématique de la mélatonine chez les enfants en bonne santé.

SOLID-LIQUID PHASE TRANSFER CATALYZED SYNTHESIS OF CINNAMYL ACETATE-KINETICS AND ANALYSIS OF FACTORS AFFECTING THE REACTION IN A BATCH REACTOR

EPA Science Inventory

The use of solid-liquid phase transfer catalysis has an advantage of carrying out reaction between two immiscible substrates, one in solid phase and the other in liquid phase, with high selectivity and at relatively low temperatures. In this study we investigated the synthesis ci...

Numerical modelling of biomass combustion: Solid conversion processes in a fixed bed furnace

NASA Astrophysics Data System (ADS)

Karim, Md. Rezwanul; Naser, Jamal

2017-06-01

Increasing demand for energy and rising concerns over global warming has urged the use of renewable energy sources to carry a sustainable development of the world. Bio mass is a renewable energy which has become an important fuel to produce thermal energy or electricity. It is an eco-friendly source of energy as it reduces carbon dioxide emissions. Combustion of solid biomass is a complex phenomenon due to its large varieties and physical structures. Among various systems, fixed bed combustion is the most commonly used technique for thermal conversion of solid biomass. But inadequate knowledge on complex solid conversion processes has limited the development of such combustion system. Numerical modelling of this combustion system has some advantages over experimental analysis. Many important system parameters (e.g. temperature, density, solid fraction) can be estimated inside the entire domain under different working conditions. In this work, a complete numerical model is used for solid conversion processes of biomass combustion in a fixed bed furnace. The combustion system is divided in to solid and gas phase. This model includes several sub models to characterize the solid phase of the combustion with several variables. User defined subroutines are used to introduce solid phase variables in commercial CFD code. Gas phase of combustion is resolved using built-in module of CFD code. Heat transfer model is modified to predict the temperature of solid and gas phases with special radiation heat transfer solution for considering the high absorptivity of the medium. Considering all solid conversion processes the solid phase variables are evaluated. Results obtained are discussed with reference from an experimental burner.

Theory of amorphous ices.

PubMed

Limmer, David T; Chandler, David

2014-07-01

We derive a phase diagram for amorphous solids and liquid supercooled water and explain why the amorphous solids of water exist in several different forms. Application of large-deviation theory allows us to prepare such phases in computer simulations. Along with nonequilibrium transitions between the ergodic liquid and two distinct amorphous solids, we establish coexistence between these two amorphous solids. The phase diagram we predict includes a nonequilibrium triple point where two amorphous phases and the liquid coexist. Whereas the amorphous solids are long-lived and slowly aging glasses, their melting can lead quickly to the formation of crystalline ice. Further, melting of the higher density amorphous solid at low pressures takes place in steps, transitioning to the lower-density glass before accessing a nonequilibrium liquid from which ice coarsens.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirka, Michael M.; Nandwana, Peeyush; Lee, Yousub

Additive manufacturing (AM) of metals is rapidly emerging as an established manufacturing process for metal components. Unlike traditional metals fabrication processes, metals fabricated via AM undergo localized thermal cycles during fabrication. As a result, AM presents the opportunity to control the liquid-solid phase transformation, i.e. material texture. But, thermal cycling presents challenges from the standpoint of solid-solid phase transformations. We will discuss the opportunities and challenges in metals AM in the context of texture control and associated solid-solid phase transformations in Ti-6Al-4V and Inconel 718.

Phase relations in the system NaCl-KCl-H2O: V. Thermodynamic-PTX analysis of solid-liquid equilibria at high temperatures and pressures

USGS Publications Warehouse

Sterner, S.M.; Chou, I.-Ming; Downs, R.T.; Pitzer, Kenneth S.

1992-01-01

The Gibbs energies of mixing for NaCl-KCl binary solids and liquids and solid-saturated NaCl-KCl-H2O ternary liquids were modeled using asymmetric Margules treatments. The coefficients of the expressions were calibrated using an extensive array of binary solvus and solidus data, and both binary and ternary liquidus data. Over the PTX range considered, the system exhibits complete liquid miscibility among all three components and extensive solid solution along the anhydrous binary. Solid-liquid and solid-solid phase equilibria were calculated by using the resulting equations and invoking the equality of chemical potentials of NaCl and KCl between appropriate phases at equilibrium. The equations reproduce the ternary liquidus and predict activity coefficients for NaCl and KCl components in the aqueous liquid under solid-saturation conditions between 673 and 1200 K from vapor saturation up to 5 kbar. In the NaCl-KCl anhydrous binary system, the equations describe phase equilibria and predict activity coefficients of the salt components for all stable compositions of solid and liquid phases between room temperature and 1200 K and from 1 bar to 5 kbar. ?? 1992.

Phase diagram of two-dimensional hard ellipses.

PubMed

Bautista-Carbajal, Gustavo; Odriozola, Gerardo

2014-05-28

We report the phase diagram of two-dimensional hard ellipses as obtained from replica exchange Monte Carlo simulations. The replica exchange is implemented by expanding the isobaric ensemble in pressure. The phase diagram shows four regions: isotropic, nematic, plastic, and solid (letting aside the hexatic phase at the isotropic-plastic two-step transition [E. P. Bernard and W. Krauth, Phys. Rev. Lett. 107, 155704 (2011)]). At low anisotropies, the isotropic fluid turns into a plastic phase which in turn yields a solid for increasing pressure (area fraction). Intermediate anisotropies lead to a single first order transition (isotropic-solid). Finally, large anisotropies yield an isotropic-nematic transition at low pressures and a high-pressure nematic-solid transition. We obtain continuous isotropic-nematic transitions. For the transitions involving quasi-long-range positional ordering, i.e., isotropic-plastic, isotropic-solid, and nematic-solid, we observe bimodal probability density functions. This supports first order transition scenarios.

Binary Solid-Liquid Phase Diagram of Phenol and t-Butanol: An Undergraduate Physical Chemistry Experiment

ERIC Educational Resources Information Center

Xu, Xinhua; Wang, Xiaogang; Wu, Meifen

2014-01-01

The determination of the solid-liquid phase diagram of a binary system is always used as an experiment in the undergraduate physical chemistry laboratory courses. However, most phase diagrams investigated in the lab are simple eutectic ones, despite the fact that complex binary solid-liquid phase diagrams are more common. In this article, the…

Phase transitions of amorphous solid acetone in confined geometry investigated by reflection absorption infrared spectroscopy.

PubMed

Shin, Sunghwan; Kang, Hani; Kim, Jun Soo; Kang, Heon

2014-11-26

We investigated the phase transformations of amorphous solid acetone under confined geometry by preparing acetone films trapped in amorphous solid water (ASW) or CCl4. Reflection absorption infrared spectroscopy (RAIRS) and temperature-programmed desorption (TPD) were used to monitor the phase changes of the acetone sample with increasing temperature. An acetone film trapped in ASW shows an abrupt change in the RAIRS features of the acetone vibrational bands during heating from 80 to 100 K, which indicates the transformation of amorphous solid acetone to a molecularly aligned crystalline phase. Further heating of the sample to 140 K produces an isotropic solid phase, and eventually a fluid phase near 157 K, at which the acetone sample is probably trapped in a pressurized, superheated condition inside the ASW matrix. Inside a CCl4 matrix, amorphous solid acetone crystallizes into a different, isotropic structure at ca. 90 K. We propose that the molecularly aligned crystalline phase formed in ASW is created by heterogeneous nucleation at the acetone-water interface, with resultant crystal growth, whereas the isotropic crystalline phase in CCl4 is formed by homogeneous crystal growth starting from the bulk region of the acetone sample.

Solid electrolyte-electrode system for an electrochemical cell

DOEpatents

Tuller, Harry L.; Kramer, Steve A.; Spears, Marlene A.

1995-01-01

An electrochemical device including a solid electrolyte and solid electrode composed of materials having different chemical compositions and characterized by different electrical properties but having the same crystalline phase is provided. A method for fabricating an electrochemical device having a solid electrode and solid electrolyte characterized by the same crystalline phase is also provided.

Two-dimensional solid-phase extraction strategy for the selective enrichment of aminoglycosides in milk.

PubMed

Shen, Aijin; Wei, Jie; Yan, Jingyu; Jin, Gaowa; Ding, Junjie; Yang, Bingcheng; Guo, Zhimou; Zhang, Feifang; Liang, Xinmiao

2017-03-01

An orthogonal two-dimensional solid-phase extraction strategy was established for the selective enrichment of three aminoglycosides including spectinomycin, streptomycin, and dihydrostreptomycin in milk. A reversed-phase liquid chromatography material (C 18 ) and a weak cation-exchange material (TGA) were integrated in a single solid-phase extraction cartridge. The feasibility of two-dimensional clean-up procedure that experienced two-step adsorption, two-step rinsing, and two-step elution was systematically investigated. Based on the orthogonality of reversed-phase and weak cation-exchange procedures, the two-dimensional solid-phase extraction strategy could minimize the interference from the hydrophobic matrix existing in traditional reversed-phase solid-phase extraction. In addition, high ionic strength in the extracts could be effectively removed before the second dimension of weak cation-exchange solid-phase extraction. Combined with liquid chromatography and tandem mass spectrometry, the optimized procedure was validated according to the European Union Commission directive 2002/657/EC. A good performance was achieved in terms of linearity, recovery, precision, decision limit, and detection capability in milk. Finally, the optimized two-dimensional clean-up procedure incorporated with liquid chromatography and tandem mass spectrometry was successfully applied to the rapid monitoring of aminoglycoside residues in milk. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Adsorption of the Three-phase Emulsion on Various Solid Surfaces.

PubMed

Enomoto, Yasutaka; Imai, Yoko; Tajima, Kazuo

2017-07-01

The present study investigates the adsorption of the three-phase emulsion on various solid/water interfaces. Vesicles can be used as emulsifiers in the three-phase emulsions and act as an independent phase unlike the surfactant used in conventional emulsions; therefore, it is expected that the three-phase emulsion formed by the adhesion of vesicles to the oil/water interface will adsorb on various solid/water interfaces. The cationic three-phase emulsion was prepared to encourage emulsion adsorption on negatively charged solid substrates in water. The emulsifier polyoxyethylene-(10) hydrogenated castor oil was rendered cationic by mixing with the surfactant cetyltrimethylammonium bromide and then used to prepare the cationic three-phase emulsion of hexadecane-in-water. Three solid substrates (silicon, glass, and copper) were dipped in the cationic emulsion and the emulsion was found to adsorb on the solid substrates while maintaining its structure. The amount of hexadecane adsorbed on the various surfaces was investigated by gas chromatography and found to increase with increasing hexadecane concentration in the emulsion and eventually plateaued just like molecular adsorption. The maximum surface coverage of the emulsion on the substrates was approximately 80%. However, even the equivalent nonionic three-phase emulsion was found to adsorb on the three solid surfaces. This was attributed to a novel mechanism of irreversible adhesion via the van der Waals attractive force.

Manual Solid-Phase Peptide Synthesis of Metallocene-Peptide Bioconjugates

ERIC Educational Resources Information Center

Kirin, Srecko I.; Noor, Fozia; Metzler-Nolte, Nils; Mier, Walter

2007-01-01

A simple and relatively inexpensive procedure for preparing a biologically active peptide using solid phase peptide synthesis (SPPS) is described. Fourth-year undergraduate students have gained firsthand experience from the solid-phase synthesis techniques and they have become familiar with modern analytical techniques based on the particular…

Effect of solid-meal caloric content on gastric emptying kinetics of solids and liquids.

PubMed

Urbain, J L; Siegel, J A; Mortelmans, L; van Cutsem, E; van den Maegdenbergh, V; de Roo, M

1989-08-01

In this study, we have evaluated the effect of the caloric content of a physiological test meal on the gastric emptying kinetics of solids and liquids. 22 healthy male volunteers were studied in two groups matched for age. After an overnight fast, each volunteer underwent the same test procedure; in the first group (G I), 10 volunteers received a meal consisting of bread, 111In-DTPA water and 1 scrambled egg labeled with 99mTc-labelled sulphur colloid; in the second group (G II) 12 volunteers were given the same meal but with 2 labeled eggs in order to increase the caloric content of the solid phase meal. Simultaneous anterior and posterior images were recorded using a dual-headed gamma camera. Solid and liquid geometric mean data were analyzed to determine the lag phase, the emptying rate and the half-emptying time for both solids and liquids. Solid and liquid gastric half-emptying times were significantly prolonged in G II compared to G I volunteers. For the solid phased, the delay was accounted for by a longer lag phase and a decrease in the equilibrium emptying rate. The emptying rate of the liquid phase was significantly decreased in G II compared to G I. Within each group, no statistically significant difference was observed between solid and liquid emptying rates. We conclude that the caloric content of the solid portion of a meal not only alters the emptying of the solid phase but also affects the emptying of the liquid component of the meal.

Dependence of the pour point of diesel fuels on the properties of the initial components

NASA Technical Reports Server (NTRS)

Ostashov, V. M.; Bobrovskiy, S. A.

1979-01-01

An analytical expression is obtained for the dependence of the pour point of diesel fuels on the pour point and weight relationship of the initial components. For determining the pour point of a multicomponent fuel mixture, it is assumed that the mixture of two components has the pour point of a separate equivalent component, then calculating the pour point of this equivalent component mixed with a third component, etc.

Global environment facility: Independent evaluation of the pilot phase; Fonds pour l`environnement mondial: evaluation independante de la phase pilote

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1994-12-31

This study responds to a request by participants in the Global Environment Facility (GEF) for an independent evaluation of the pilot phase. It profiles the GEF, discusses its policy framework, and reviews project development procedures and the strategies and projects in each of the GEF`s four focal areas. The study concludes that fundamental changes must occur and recommends specific reforms, such as articulating more clearly the GEF`s mandate, objectives, and strategies; addressing deficiencies in meeting its global focus; improving capacities and procedures within implementing agencies for managing the portfolio; and increasing non-government organization (NGO), country and community-level participation.

Carbon cloth supported electrode

DOEpatents

Lu, Wen-Tong P.; Ammon, Robert L.

1982-01-01

A flow-by anode is disclosed made by preparing a liquid suspension of about to about 18% by weight solids, the solids comprising about 3.5 to about 8% of a powdered catalyst of platinum, palladium, palladium oxide, or mixtures thereof; about 60 to about 76% carbon powder (support) having a particle size less than about 20 m.mu.m and about 20 to about 33% of an inert binder having a particle size of less than about 500 m.mu.m. A sufficient amount of the suspension is poured over a carbon cloth to form a layer of solids about 0.01 to about 0.05 cm thick on the carbon cloth when the electrode is completed. A vacuum was applied to the opposite side of the carbon cloth to remove the liquid and the catalyst layer/cloth assembly is dried and compressed at about 10 to about 50 MPa's. The binder is then sintered in an inert atmosphere to complete the electrode. The electrode is used for the oxidation of sulfur dioxide in a sulfur based hybrid cycle for the decomposition of water.

Crystals with a surface deformed by a non-epitaxial growth (in French)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1972-11-30

Ces cristaux sont obtenus par mise en contact avec un agent generateur de cristaux solides, finement divise, ayant des dimensions particulaires comprises entre moins de 44 microns et 175 microns environ, pendant un laps de temps predetermine, l'agent generateur de cristaux etant associe a une quantite suffisante d'une fraction transferable capable d'engendrer par croissance une couche non epitaxiale sur la surface du cristal de base, cette croissance ayant lieu d'une maniere sensiblement uniforme mais neanmoins non ordonnee, independante de l'orientation microscopique du cristal de base. Ces cristaux peuvent etre utilises pour des scintillateurs. (FR)

Curable liquid hydrocarbon prepolymers containing hydroxyl groups and process for producing same

NASA Technical Reports Server (NTRS)

Rhein, R. A.; Ingham, J. D. (Inventor)

1978-01-01

Production of hydroxyl containing curable liquid hydrocarbon prepolymers by ozonizing a high molecular weight saturated hydrocarbon polymer such as polyisobutylene or ethylene propylene rubber is discussed. The ozonized material is reduced using reducing agents, preferably diisobutyl aluminum hydride, to form the hydroxyl containing liquid prepolymers having a substantially lower molecular weight than the parent polymer. The resulting curable liquid hydroxyl containing prepolymers can be poured into a mold and readily cured, with reactants such as toluene diisocyanate, to produce highly stable elastomers having a variety of uses such as binders for solid propellants.

Theory of amorphous ices

PubMed Central

Limmer, David T.; Chandler, David

2014-01-01

We derive a phase diagram for amorphous solids and liquid supercooled water and explain why the amorphous solids of water exist in several different forms. Application of large-deviation theory allows us to prepare such phases in computer simulations. Along with nonequilibrium transitions between the ergodic liquid and two distinct amorphous solids, we establish coexistence between these two amorphous solids. The phase diagram we predict includes a nonequilibrium triple point where two amorphous phases and the liquid coexist. Whereas the amorphous solids are long-lived and slowly aging glasses, their melting can lead quickly to the formation of crystalline ice. Further, melting of the higher density amorphous solid at low pressures takes place in steps, transitioning to the lower-density glass before accessing a nonequilibrium liquid from which ice coarsens. PMID:24858957

Electron drift in a large scale solid xenon

DOE PAGES

Yoo, J.; Jaskierny, W. F.

2015-08-21

A study of charge drift in a large scale optically transparent solid xenon is reported. A pulsed high power xenon light source is used to liberate electrons from a photocathode. The drift speeds of the electrons are measured using a 8.7 cm long electrode in both the liquid and solid phase of xenon. In the liquid phase (163 K), the drift speed is 0.193 ± 0.003 cm/μs while the drift speed in the solid phase (157 K) is 0.397 ± 0.006 cm/μs at 900 V/cm over 8.0 cm of uniform electric fields. Furthermore, it is demonstrated that a factor twomore » faster electron drift speed in solid phase xenon compared to that in liquid in a large scale solid xenon.« less

Grain Floatation During Equiaxed Solidification of an Al-Cu Alloy in a Side-Cooled Cavity: Part II—Numerical Studies

NASA Astrophysics Data System (ADS)

Kumar, Arvind; Walker, Mike J.; Sundarraj, Suresh; Dutta, Pradip

2011-08-01

In this article, a single-phase, one-domain macroscopic model is developed for studying binary alloy solidification with moving equiaxed solid phase, along with the associated transport phenomena. In this model, issues such as thermosolutal convection, motion of solid phase relative to liquid and viscosity variations of the solid-liquid mixture with solid fraction in the mobile zone are taken into account. Using the model, the associated transport phenomena during solidification of Al-Cu alloys in a rectangular cavity are predicted. The results for temperature variation, segregation patterns, and eutectic fraction distribution are compared with data from in-house experiments. The model predictions compare well with the experimental results. To highlight the influence of solid phase movement on convection and final macrosegregation, the results of the current model are also compared with those obtained from the conventional solidification model with stationary solid phase. By including the independent movement of the solid phase into the fluid transport model, better predictions of macrosegregation, microstructure, and even shrinkage locations were obtained. Mechanical property prediction models based on microstructure will benefit from the improved accuracy of this model.

Solid phase pegylation of hemoglobin.

PubMed

Suo, Xiaoyan; Zheng, Chunyang; Yu, Pengzhan; Lu, Xiuling; Ma, Guanghui; Su, Zhiguo

2009-01-01

A solid phase conjugation process was developed for attachment of polyethylene glycol to hemoglobin molecule. Bovine hemoglobin was loaded onto an ion exchange chromatography column and adsorbed by the solid medium. Succinimidyl carbonate mPEG was introduced in the mobile phase after the adsorption. Pegylation took place between the hemoglobin on the solid phase, and the pegylation reagent in the liquid phase. A further elution was carried out to separate the pegylated and the unpegylated protein. Analysis by HPSEC, SDS-PAGE, and MALLS demonstrated that the fractions eluted from the solid phase contained well-defined components. Pegylated hemoglobin with one PEG chain was obtained with the yield of 75%, in comparison to the yield of 30% in the liquid phase pegylation. The P(50) values of the mono-pegylated hemoglobin, prepared with SC-mPEG 5 kDa, 10 kDa and 20 kDa, were 19.97, 20.23 and 20.54 mmHg, which were much closer to the value of red blood cells than that of pegylated hemoglobin prepared with the conventional method.

Mechanism of Formation of Li 7 P 3 S 11 Solid Electrolytes through Liquid Phase Synthesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Yuxing; Lu, Dongping; Bowden, Mark

Crystalline Li7P3S11 is a promising solid electrolyte for all solid state lithium/lithium ion batteries. A controllable liquid phase synthesis of Li7P3S11 is more desirable compared to conventional mechanochemical synthesis, but recent attempts suffer from reduced ionic conductivities. Here we elucidate the formation mechanism of crystalline Li7P3S11 synthesized in the liquid phase (acetonitrile, or ACN). We conclude that the crystalline Li7P3S11 forms through a two-step reaction: 1) formation of solid Li3PS4∙ACN and amorphous Li2S∙P2S5 phases in the liquid phase; 2) solid-state conversion of the two phases. The implication of this two-step reaction mechanism to the morphology control and the transport propertiesmore » of liquid phase synthesized Li7P3S11 is identified and discussed.« less

Runaway reactions, their courses and the methods to establish safe process conditions

NASA Astrophysics Data System (ADS)

Gustin, J. L.

1991-08-01

Much of the literature on runaway reactions deals with the consequences such as mechanical damage toxic and flammable release. The DIERS literature provides effective methods for vent sizing where experimental information is requested. Thermal stability measurements provide information on the onset temperature and kinetic data for chemical reactions. There is less information on the way the runaway reactions occur whereas the runaway reactions may have different causes. The purpose of this paper is to describe the various process deviations which can cause a runaway reaction to occur and to discuss the experimental information necessary for risk assessment, the choice of a safe process and the mitigation of the consequences of the runaway reaction. Each possible hazardous process deviation is illustrated by examples from the process industry and/or relevant experimental information obtained from laboratory experiments. The typical hazardous situations to be considered are the following: 1) The homogeneous thermal runaway due to too high a temperature. 2) The homogeneous runaway reaction by unintended introduction of additional reactants or catalyst. 3) The heterogeneous runaway reaction due to too high a local temperature. 4) The heterogeneous runaway reaction caused by slow heat conduction to the outside. 5) The runaway reaction caused by excess residence time at the process temperature (autocatalytic reactions). 6) The runaway reaction caused by reactant accumulation. The controling reactant feed rate is higher than the consumption rate perhaps because the temperature is too low, or the catalyst is absent. 7) The runaway reaction due to the pressurization of the enclosure by gaseous oxidizing intermediates (typical of nitric oxidations). 8) The runaway reaction due to phase separation of unstable species (liquids, solids) by loss of mixing or on cooling. 9) The runaway reaction on mixing of fast reacting chemicals in separate phases. 10)The runaway reaction due to fire or external heating. Considering the various runaway situations, the effectiveness of the following approaches is discussed: - Theoretical and experimental information required for hazard assessment. - Choice of adequate process conditions. - Choice of adequate methods for process control. - Experimental information required for vent sizing. La plus grande partie de la littérature sur les emballements thermiques traite des conséquences de l'accident telles que les effets mécaniques, les émissions toxiques et inflammables. Les travaux publiés par le DIERS fournissent des méthodes permettant le dimensionnement d'évents, nécessitant des déterminations expérimentales. Il y a moins d'information sur la manière dont les emballements thermiques peuvent survenir alors que ceux-ci peuvent avoir différentes causes. Le propos de cet article est de décrire les différentes dérives de procédé qui peuvent entraîner un emballement thermique et de déterminer l'information expérimentale nécessaire pour l'analyse des risques du procédé, le choix de conditions opératoires sûres et la réduction des conséquences de l'emballement thermique. Chaque dérive de procédé dangereuse, est illustrée par des exemples connus dans l'industrie chimique et par des données expérimentales obtenues dans des essais de laboratoire. Les conditions de procédé dangereuses prises en compte sont les suivantes: 1)L'emballement thermique homogène dû à une température excessive; 2) L'emballement thermique homogène par introduction d'un catalyseur ou d'un réactif contrôlant; 3) L'emballement thermique hétérogène dû à une température locale excessive; 4)L'emballement thermique hétérogène dû à une faible conduction thermique vers l'extérieur; 5) L'emballement thermique dû à un temps de séjour excessif à la température du procédé (Réactions autocatalytiques); 6) L'emballement thermique par accumulation de réactifs. La vitesse d'introduction d'un réactif contrôlant est supérieure à la vitesse de consommation de ce réactif, parce que la température est trop basse ou le catalyseur absent; 7) L'emballement thermique dû à la pressurisation d'une enceinte par des intermédiaires gazeux oxydants (situation caractéristique des oxydations nitriques), 8)L'emballement thermique dû à la séparation de phases contenant des espèces instables (liquides, solides) par perte de l'agitation ou par refroidissement; 9) L'emballement thermique par mélange de produits incompatibles, se trouvant précédemment dans des phases séparées; 10) L'emballement thermique dû à un chauffage externe ou à un feu. Considérant les différentes situations conduisant à un emballement thermique, l'intérêt de l'approche systématique suivante est examiné: - Information théorique et expérimentale nécessaire pour déterminer les risques du procédé. - Choix de conditions opératoires adéquates. - Choix de méthodes convenables pour le contrôle du procédé. - Information expérimentale nécessaire pour le calcul d'évent.

Engineered glass seals for solid-oxide fuel cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Surdoval, Wayne; Lara-Curzio, Edgar; Stevenson, Jeffry

2017-02-07

A seal for a solid oxide fuel cell includes a glass matrix having glass percolation therethrough and having a glass transition temperature below 650.degree. C. A deformable second phase material is dispersed in the glass matrix. The second phase material can be a compliant material. The second phase material can be a crushable material. A solid oxide fuel cell, a precursor for forming a seal for a solid oxide fuel cell, and a method of making a seal for a solid oxide fuel cell are also disclosed.

Solid electrolyte-electrode system for an electrochemical cell

DOEpatents

Tuller, H.L.; Kramer, S.A.; Spears, M.A.

1995-04-04

An electrochemical device including a solid electrolyte and solid electrode composed of materials having different chemical compositions and characterized by different electrical properties but having the same crystalline phase is provided. A method for fabricating an electrochemical device having a solid electrode and solid electrolyte characterized by the same crystalline phase is also provided. 17 figures.

Experimental Investigation of the Strength of Damaged Pressure Hulls - Phases 5 & 6: The Influence of Out-of-Circularity on Collapse

DTIC Science & Technology

2011-03-01

showed a similar response as its companion specimen, L510-No13. Figure 76 shows the circumferential distribution of shell strain at the collapse...Defence R&D Canada Canada’s leader in defence and National Security Science and Technology R & D pour Ia defense Canada Chef de file au Canada en

Rapid determination of the volatile components in tobacco by ultrasound-microwave synergistic extraction coupled to headspace solid-phase microextraction with gas chromatography-mass spectrometry.

PubMed

Yang, Yanqin; Chu, Guohai; Zhou, Guojun; Jiang, Jian; Yuan, Kailong; Pan, Yuanjiang; Song, Zhiyu; Li, Zuguang; Xia, Qian; Lu, Xinbo; Xiao, Weiqiang

2016-03-01

An ultrasound-microwave synergistic extraction coupled to headspace solid-phase microextraction was first employed to determine the volatile components in tobacco samples. The method combined the advantages of ultrasound, microwave, and headspace solid-phase microextraction. The extraction, separation, and enrichment were performed in a single step, which could greatly simplify the operation and reduce the whole pretreatment time. In the developed method, several experimental parameters, such as fiber type, ultrasound power, and irradiation time, were optimized to improve sampling efficiency. Under the optimal conditions, there were 37, 36, 34, and 36 components identified in tobacco from Guizhou, Hunan, Yunnan, and Zimbabwe, respectively, including esters, heterocycles, alkanes, ketones, terpenoids, acids, phenols, and alcohols. The compound types were roughly the same while the contents were varied from different origins due to the disparity of their growing conditions, such as soil, water, and climate. In addition, the ultrasound-microwave synergistic extraction coupled to headspace solid-phase microextraction method was compared with the microwave-assisted extraction coupled to headspace solid-phase microextraction and headspace solid-phase microextraction methods. More types of volatile components were obtained by using the ultrasound-microwave synergistic extraction coupled to headspace solid-phase microextraction method, moreover, the contents were high. The results indicated that the ultrasound-microwave synergistic extraction coupled to headspace solid-phase microextraction technique was a simple, time-saving and highly efficient approach, which was especially suitable for analysis of the volatile components in tobacco. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Numerical investigation of influence on heat transfer characteristics to pneumatically conveyed dense phase flow by selecting models and boundary conditions

NASA Astrophysics Data System (ADS)

Zheng, Y.; Liu, Q.; Li, Y.

2012-03-01

Solids moving with a gas stream in a pipeline can be found in many industrial processes, such as power generation, chemical, pharmaceutical, food and commodity transfer processes. A mass flow rate of the solids is important characteristic that is often required to be measured (and controlled) to achieve efficient utilization of energy and raw materials in pneumatic conveying systems. The methods of measuring the mass flow rate of solids in a pneumatic pipeline can be divided into direct and indirect (inferential) measurements. A thermal solids' mass flow-meter, in principle, should ideally provide a direct measurement of solids flow rate, regardless of inhomogeneities in solids' distribution and environmental impacts. One key issue in developing a thermal solids' mass flow-meter is to characterize the heat transfer between the hot pipe wall and the gas-solids dense phase flow. The Eulerian continuum modeling with gas-solid two phases is the most common method for pneumatic transport. To model a gas-solid dense phase flow passing through a heated region, the gas phase is described as a continuous phase and the particles as the second phase. This study aims to describe the heat transfer characteristics between the hot wall and the gas-solids dense phase flow in pneumatic pipelines by modeling a turbulence gas-solid plug passing through the heated region which involves several actual and crucial issues: selections of interphase exchange coefficient, near-wall region functions and different wall surface temperatures. A sensitivity analysis was discussed to identify the influence on the heat transfer characteristics by selecting different interphase exchange coefficient models and different boundary conditions. Simulation results suggest that sensitivity analysis in the choice of models is very significant. The simulation results appear to show that a combination of choosing the Syamlal-O'Brien interphase exchange coefficient model and the standard k-ɛ model along with the standard wall function model might be the best approach, by which, the simulation data seems to be closest to the experimental results.

Liquid-phase and solid-phase microwave irradiations for reduction of graphite oxide

NASA Astrophysics Data System (ADS)

Zhao, Na; Wen, Chen-Yu; Zhang, David Wei; Wu, Dong-Ping; Zhang, Zhi-Bin; Zhang, Shi-Li

2014-12-01

In this paper, two microwave irradiation methods: (i) liquid-phase microwave irradiation (MWI) reduction of graphite oxide suspension dissolved in de-ionized water and N, N-dimethylformamide, respectively, and (ii) solid-phase MWI reduction of graphite oxide powder have been successfully carried out to reduce graphite oxide. The reduced graphene oxide products are thoroughly characterized by scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectral analysis, Raman spectroscopy, UV-Vis absorption spectral analysis, and four-point probe conductivity measurements. The results show that both methods can efficiently remove the oxygen-containing functional groups attached to the graphite layers, though the solid-phase MWI reduction method can obtain far more efficiently a higher quality-reduced graphene oxide with fewer defects. The I(D)/I(G) ratio of the solid-phase MWI sample is as low as 0.46, which is only half of that of the liquid-phase MWI samples. The electrical conductivity of the reduced graphene oxide by the solid method reaches 747.9 S/m, which is about 25 times higher than that made by the liquid-phase method.

Comparative features of volcanoes on Solar system bodies

NASA Astrophysics Data System (ADS)

Vidmachenko, A. P.

2018-05-01

The bark of many cosmic bodies is in motion because of the displacement of tectonic plates on magma. Pouring molten magma through cracks in the cortex is called a volcanic eruption. There are two main types of volcanoes: basaltic, appearing where a new material of tectonic plates is formed, and andesitic, which located in the places of destruction of these plates.The third type of volcanoes is cryovolcanoes, or ice volcanoes. This type of volcano ejects matter in the form of ice volcanic melts or steam from water, ammonia, methane. After the eruption, the cryomagma at a low temperature condenses to a solid phase. Cryovolcanoes can be formed on such objects as Pluto, Ceres, Titan, Enceladus, Europe, Triton, etc. Potential sources of energy for melting ice in the production of cryovolcanoes are tidal friction and/or radioactive decay. Semi-transparent deposits of frozen materials that can create a subsurface greenhouse effect, with the possibility of accumulating the required heat with subsequent explosive eruption, are another way to start the cryovolcano action. This type of eruption is observed on Mars and Triton. The first and second types of eruptions (basaltic and andesitic) are characteristic of terrestrial planets (Mercury, Venus, Mars) and for some satellites of the planets of the Solar system.

Estimating production and consumption of solid reactive Fe phases in marine sediments from concentration profiles

EPA Science Inventory

1D diffusion models may be used to estimate rates of production and consumption of dissolved metabolites in marine sediments, but are applied less often to the solid phase. Here we used a numerical inverse method to estimate solid phase Fe(III) and Fe(II) consumption and product...

Comparaison des Champs de Pression Instationnaires Calcules et Mesures sur le Modele ZKP (Comparison of Unstable Pressure Fields Calculated and Measured on the ZKP Model),

DTIC Science & Technology

1980-08-01

bord de fuite. Le nombre de Mach Man’est donc d~fini qu’entre deux limites et seule I’expdrience peut nous permettre de ...Si ion consid~re lea valeurs de Ia portance at du moment quart avant pour ce cas on obtient le tableau suivant: CC rsn Module Phase Module Phase P.P.T...Comparaison des Champs de Pression Instationnaires Calcules et Mesures sur le Mod ele ZK P COMPARISON OF UNSTABLE PRESSURE FIELDS .- %P, CALCULATED

Cementitious building material incorporating end-capped polyethylene glycol as a phase change material

DOEpatents

Salyer, Ival O.; Griffen, Charles W.

1986-01-01

A cementitious composition comprising a cementitious material and polyethylene glycol or end-capped polyethylene glycol as a phase change material, said polyethylene glycol and said end-capped polyethylene glycol having a molecular weight greater than about 400 and a heat of fusion greater than about 30 cal/g; the compositions are useful in making pre-formed building materials such as concrete blocks, brick, dry wall and the like or in making poured structures such as walls or floor pads; the glycols can be encapsulated to reduce their tendency to retard set.

Caractérisations structurale et morphologique des couches minces de CuInS2 et d'In-S "airless spray"

NASA Astrophysics Data System (ADS)

Kamoun, N.; Belgacem, S.; Amlouk, M.; Bennaceur, R.; Abdelmoula, K.; Belhadj Amara, A.

1994-03-01

We have prepared CuInS2 thin layers by airless spray "S.P.A." in order to use them as an absorber in a photovoltaic cell. The X-ray diffraction analysis has showed that these layers are well crystallized with a privileged (112) principal orientation for a ratio of the concentrations in the pulverized solution x=frac[Cu^I][In^{III]}=1.1. After heat treatment under vacuum the crystallization have been clearly improved. The structural analysis of the thin CuInS2 layers have revealed that a secondary phases of In2S3 and In6S7 are present. Thus we have realized by the same technique thin In-S layers whose structural and morphological properties have been studied. This analysis has showed that the In-S layers are well crystallized for a ratio y=frac[In^{3+]}[S^{2-]}=0.6 in the spray solution. The In-S layers are essentially formed by a β-In2S3 material. Although the In6S7 phase appears to the detriment of β-In2S3 phase for y= 0.75. Nous avons préparé des couches minces de CuInS2, par pulvérisation chimique réactive sans air "P.S.A.", en vue de leur utilisation en tant qu'absorbeur dans un dispositif photovoltaïque. L'analyse par diffraction X a montré que ces couches sont bien cristallisées et que l'orientation principale (112) est privilégiée pour un rapport de concentrations x=frac[Cu^I]{[In^{III}]}=1,1 dans la solution à pulvériser. Après le traitement thermique sous vide la cristallisation est nettement améliorée. L'analyse structurale des couches minces de CuInS2 a révélé que ces couches renferment des phases secondaires d'In2S3 et d'In6S7. Ainsi nous avons réalisé par la même technique "P.S.A.", des couches minces d'In-S dont nous avons étudié les propriétés structurales et morphologiques, Cette analyse a montré que les couches d'In-S sont bien cristallisées. Pour un rapport de concentrations en solution de pulvérisation y=frac[In^{3+]}[S^{2-]}=0,6 les couches d'In-S sont surtout formées du matériau β-In2S3. Alors que la phase In6S7 apparaît au détriment de la phase β-In2S3 pour y= 0,75.

Recent Application of Solid Phase Based Techniques for Extraction and Preconcentration of Cyanotoxins in Environmental Matrices.

PubMed

Mashile, Geaneth Pertunia; Nomngongo, Philiswa N

2017-03-04

Cyanotoxins are toxic and are found in eutrophic, municipal, and residential water supplies. For this reason, their occurrence in drinking water systems has become a global concern. Therefore, monitoring, control, risk assessment, and prevention of these contaminants in the environmental bodies are important subjects associated with public health. Thus, rapid, sensitive, selective, simple, and accurate analytical methods for the identification and determination of cyanotoxins are required. In this paper, the sampling methodologies and applications of solid phase-based sample preparation methods for the determination of cyanotoxins in environmental matrices are reviewed. The sample preparation techniques mainly include solid phase micro-extraction (SPME), solid phase extraction (SPE), and solid phase adsorption toxin tracking technology (SPATT). In addition, advantages and disadvantages and future prospects of these methods have been discussed.

Modulated structure and molecular dissociation of solid chlorine at high pressures

NASA Astrophysics Data System (ADS)

Li, Peifang; Gao, Guoying; Ma, Yanming

2012-08-01

Among diatomic molecular halogen solids, high pressure structures of solid chlorine (Cl2) remain elusive and least studied. We here report first-principles structural search on solid Cl2 at high pressures through our developed particle-swarm optimization algorithm. We successfully reproduced the known molecular Cmca phase (phase I) at low pressure and found that it remains stable up to a high pressure 142 GPa. At 150 GPa, our structural searches identified several energetically competitive, structurally similar, and modulated structures. Analysis of the structural results and their similarity with those in solid Br2 and I2, it was suggested that solid Cl2 adopts an incommensurate modulated structure with a modulation wave close to 2/7 in a narrow pressure range 142-157 GPa. Eventually, our simulations at >157 GPa were able to predict the molecular dissociation of solid Cl2 into monatomic phases having body centered orthorhombic (bco) and face-centered cubic (fcc) structures, respectively. One unique monatomic structural feature of solid Cl2 is the absence of intermediate body centered tetragonal (bct) structure during the bco → fcc transition, which however has been observed or theoretically predicted in solid Br2 and I2. Electron-phonon coupling calculations revealed that solid Cl2 becomes superconductors within bco and fcc phases possessing a highest superconducting temperature of 13.03 K at 380 GPa. We further probed the molecular Cmca → incommensurate phase transition mechanism and found that the softening of the Ag vibrational (rotational) Raman mode in the Cmca phase might be the driving force to initiate the transition.

Solid-solution CrCoCuFeNi high-entropy alloy thin films synthesized by sputter deposition

DOE PAGES

An, Zhinan; Jia, Haoling; Wu, Yueying; ...

2015-05-04

The concept of high configurational entropy requires that the high-entropy alloys (HEAs) yield single-phase solid solutions. However, phase separations are quite common in bulk HEAs. A five-element alloy, CrCoCuFeNi, was deposited via radio frequency magnetron sputtering and confirmed to be a single-phase solid solution through the high-energy synchrotron X-ray diffraction, energy-dispersive spectroscopy, wavelength-dispersive spectroscopy, and transmission electron microscopy. The formation of the solid-solution phase is presumed to be due to the high cooling rate of the sputter-deposition process.

Approximation auto-coherente a deux particules, pseudogap et supraconductivite dans le modele de Hubbard attractif

NASA Astrophysics Data System (ADS)

Allen, Steve

2000-10-01

Dans cette these nous presentons une nouvelle methode non perturbative pour le calcul des proprietes d'un systeme de fermions. Notre methode generalise l'approximation auto-coherente a deux particules proposee par Vilk et Tremblay pour le modele de Hubbard repulsif. Notre methode peut s'appliquer a l'etude du comportement pre-critique lorsque la symetrie du parametre d'ordre est suffisamment elevee. Nous appliquons la methode au probleme du pseudogap dans le modele de Hubbard attractif. Nos resultats montrent un excellent accord avec les donnees Monte Carlo pour de petits systemes. Nous observons que le regime ou apparait le pseudogap dans le poids spectral a une particule est un regime classique renormalise caracterise par une frequence caracteristique des fluctuations supraconductrices inferieure a la temperature. Une autre caracteristique est la faible densite de superfluide de cette phase demontrant que nous ne sommes pas en presence de paires preformees. Les resultats obtenus semblent montrer que la haute symetrie du parametre d'ordre et la bidimensionalite du systeme etudie elargissent le domaine de temperature pour lequel le regime pseudogap est observe. Nous argumentons que ce resultat est transposable aux supraconducteurs a haute temperature critique ou le pseudogap apparait a des' temperatures beaucoup plus grandes que la temperature critique. La forte symetrie dans ces systemes pourraient etre reliee a la theorie SO(5) de Zhang. En annexe, nous demontrons un resultat tout recent qui permettrait d'assurer l'auto-coherence entre les proprietes a une et a deux particules par l'ajout d'une dynamique au vertex irreductible. Cet ajout laisse entrevoir la possibilite d'etendre la methode au cas d'une forte interaction.

Method for making an electrochemical cell

DOEpatents

Tuller, Harry L.; Kramer, Steve A.; Spears, Marlene A.; Pal, Uday B.

1996-01-01

An electrochemical device including a solid electrolyte and solid electrode composed of materials having different chemical compositions and characterized by different electrical properties but having the same crystalline phase is provided. A method for fabricating an electrochemical device having a solid electrode and solid electrolyte characterized by the same crystalline phase is provided.

Pressure induced solid-solid reconstructive phase transition in LiGa O2 dominated by elastic strain

NASA Astrophysics Data System (ADS)

Hu, Qiwei; Yan, Xiaozhi; Lei, Li; Wang, Qiming; Feng, Leihao; Qi, Lei; Zhang, Leilei; Peng, Fang; Ohfuji, Hiroaki; He, Duanwei

2018-01-01

Pressure induced solid-solid reconstructive phase transitions for graphite-diamond, and wurtzite-rocksalt in GaN and AlN occur at significantly higher pressure than expected from equilibrium coexistence and their transition paths are always inconsistent with each other. These indicate that the underlying nucleation and growth mechanism in the solid-solid reconstructive phase transitions are poorly understood. Here, we propose an elastic-strain dominated mechanism in a reconstructive phase transition, β -LiGa O2 to γ -LiGa O2 , based on in situ high-pressure angle dispersive x-ray diffraction and single-crystal Raman scattering. This mechanism suggests that the pressure induced solid-solid reconstructive phase transition is neither purely diffusionless nor purely diffusive, as conventionally assumed, but a combination. The large elastic strains are accumulated, with the coherent nucleation, in the early stage of the transition. The elastic strains along the 〈100 〉 and 〈001 〉 directions are too large to be relaxed by the shear stress, so an intermediate structure emerges reducing the elastic strains and making the transition energetically favorable. At higher pressures, when the elastic strains become small enough to be relaxed, the phase transition to γ -LiGa O2 begins and the coherent nucleation is substituted with a semicoherent one with Li and Ga atoms disordered.

Comparison of the solid-phase extraction efficiency of a bounded and an included cyclodextrin-silica microporous composite for polycyclic aromatic hydrocarbons determination in water samples.

PubMed

Mauri-Aucejo, Adela; Amorós, Pedro; Moragues, Alaina; Guillem, Carmen; Belenguer-Sapiña, Carolina

2016-08-15

Solid-phase extraction is one of the most important techniques for sample purification and concentration. A wide variety of solid phases have been used for sample preparation over time. In this work, the efficiency of a new kind of solid-phase extraction adsorbent, which is a microporous material made from modified cyclodextrin bounded to a silica network, is evaluated through an analytical method which combines solid-phase extraction with high-performance liquid chromatography to determine polycyclic aromatic hydrocarbons in water samples. Several parameters that affected the analytes recovery, such as the amount of solid phase, the nature and volume of the eluent or the sample volume and concentration influence have been evaluated. The experimental results indicate that the material possesses adsorption ability to the tested polycyclic aromatic hydrocarbons. Under the optimum conditions, the quantification limits of the method were in the range of 0.09-2.4μgL(-1) and fine linear correlations between peak height and concentration were found around 1.3-70μgL(-1). The method has good repeatability and reproducibility, with coefficients of variation under 8%. Due to the concentration results, this material may represent an alternative for trace analysis of polycyclic aromatic hydrocarbons in water trough solid-phase extraction. Copyright © 2016 Elsevier B.V. All rights reserved.

Remarks on Polyelectrolyte Conformation

NASA Astrophysics Data System (ADS)

de Gennes, P. G.; Pincus, P.; Velasco, R. M.; Brochard, F.

Nous discutons des conformations de polymères linéaires chargés en faisant les hypothèses suivantes : a) la chaĬne sans charge est flexible, b) la force éctrostatique domine les interactions monomère-monomère c) il n'y a pas de sels. 1) Pour le cas dilué (chaĬne non enchevetrees) en corrigeant le calcul self-consistant fait récemment par Richmond [1a], on trouve une taille des polyions égale a = R ND, qui est une fonction linéaire de l'indice de polymérisation N. Ce rèsultat est en accord avec les prècèdents travaux de Hermans et Overbeek [1b], Kuhn, Kunzle et Katchalsky [1c]. 2) Il existe un domaine pour des concentrations très petites c (c** < c < c*) oò les interactions èlectrostatiques entre les polyions sont supèrieures aux ènergies thermiques, il semble donc possible que les polyions puissent former un rèseau pèriodique à trois dimensions. Nèanmoins, il semble difficile de mettre en èvidence un rèseau si diluè. 3) Jusqu'ici toutes les expériences avec les polyélectrolytes sans sels ont été pratiquement faites à des concentrations c > c*, pour lesquelles les différentes cha.nes sont enchevêtrées. Pour discuter ce régime on s.intéresse uniquement au cas où la charge par unité de longueur est près du (ou audessus du) seuil de condensation, donc il existe une seule longueur ξ(c) caractérisant les corrélations; à trois dimensions 03BE a le même comportement que le rayon de Debye pour les contre-ions. On a considéré quelques conformations possibles : a) un réseau hexagonal de batonnets; b) un réseau cubique de batonnets; c) une phase isotrope de cha.nes partiellement flexibles. Les différentes structures formées de batonnets semblent avoir la même énergie électrostatique. Ce fait suggère que la phase isotrope peut être la plus favorable. On analyse cette dernière phase en utilisant les mêmes méthodes qui se sont révélées efficaces pour les solutions des polymères neutres. Dans le modèle isotrope chaque cha.ne a le comportement d.une succession des petites pelotes (blobs) de taille 03BE. Les effets électrostatiques sont importants à l.intérieur d'un blobs et analogues au cas (1). Mais ces interactions sont écrantées entre les blobs ; chaque cha.ne a un comportement idéal à grande échelle et son rayon est R(c) ~ c-¼ N½. Si on suppose que les effets dynamiques des enchevêtrements sont faibles on trouve une valeur pour la viscosité ηsp/c ~ Nc-½ We discuss the conformations of linear polyions assuming that a) the corresponding uncharged chain is flexible ; b) electrostatic forces dominate the monomer-monomer interactions; c) no salt is added. 1) For the dilute case (non overlapping chains) correcting a recent self-consistent calculation by Richmond [1a], we find an overall polyion size R = Nd which is a linear function of the polymerization index N in agreement with the early work of Hermans and Overbeek, [1b], Kuhn, Kunzle, and Katchalsky [1c]. 2) There is a range of very low concentration c (c** < c < c*) where the chains do not overlap (c < c*) but where the electrostatic interactions between polyions are much larger than thermal energies (c > c**) : here we expect that the polyions build up a 3-dimensional periodic lattice ; however, the detection of such an extremely dilute lattice appears difficult. 3) Practically all experiments on salt-free polyelectrolytes have been performed at concentrations c > c* where different chains overlap each other. To discuss this regime we restrict our attention to cases where the charge per unit length is near (or above) the condensation threshold : then a single length ξ(c) characterizes the correlation; in 3 dimensions ξ scales like the Debye radius associated with the counter ions. We consider several possible conformations : a) hexagonal lattice of rigid rods ; b) cubic lattice of rigid rods; c) isotropic phase of partially flexible chains. The various rigid rod structures appear to have very similar electrostatic energies. This suggests that the isotropic phase might possibly be the most favorable. We analyse this latter phase using the same scaling methods which have recently been helpful for neutral polymer solutions (2). In the isotropic model each chain behaves like a succession of segments of size. Inside one segment electrostatic effects are important and similar to case (1) above. Between segments the interactions are screened out, and tach chain is ideal on a large scale, with radius R(c) ~ c-¼ N½. If we (tentatively) assume that the dynamical effects of entanglements are weak, we are than led to a viscosity ηsp/c ~ Nc-½.

The Iron-Iron Carbide Phase Diagram: A Practical Guide to Some Descriptive Solid State Chemistry.

ERIC Educational Resources Information Center

Long, Gary J.; Leighly, H. P., Jr.

1982-01-01

Discusses the solid state chemistry of iron and steel in terms of the iron-iron carbide phase diagram. Suggests that this is an excellent way of introducing the phase diagram (equilibrium diagram) to undergraduate students while at the same time introducing the descriptive solid state chemistry of iron and steel. (Author/JN)

Étalement d'une goutte stratifiée incompressible

NASA Astrophysics Data System (ADS)

de Gennes, Pierre-Gilles; Cazabat, Anne-Marie

L'étalement de films ultraminces de liquides simples sur une surface lisse horizontale conduit souvent à des gouttes à gradins d'une épaisseur moléculaire ([1]-[3]). Nous construisons ici un modèle pour la dynamique de l'étalement, en supposant que : (a) chaque gradin est un liquide bidimensionnel incompressible; (b) les molécules de la n-ième couche sont soumises à un potentiel (Wn) qui exprime leurs interactions à longue portée avec le solide; (c) on a un écoulement parallèle de cisaillement, et un écoulement normal de perméation. La perméation intervient seulement dans un certain « ruban » de largeur ξ sur le bord de chaque gradin. Dans le cas usuel, où le rayon du n-ième gradin Rn est trs supérieur à ξ, la dissipation est dominée par le cisaillement, et on arrive à des lois simples pour la vitesse de dilatation (ou de contraction) dotR_n. Very thin films of simple liquids often spread with well defined steps of molecular thickness ([1]-[3]). We construct a model for the dynamics of spreading assuming that: (a) each layer is an incompressible, 2 dimensional fluid; (b) the molecules in the (nth) layer experience a long range potential (e.g. Van der Waals) from the solid; (c) two types of flow occur: shear between layers and permeation normal to the layers. We find that permeation is important only in an annulus of small size ξ near each step. Between steps, the viscous effects in simple shear dominate, and this leads to simple laws for the dilation (or contraction) of the various layers.

An Investigation into the Polymorphism and Crystallization of Levetiracetam and the Stability of its Solid Form.

PubMed

Xu, Kailin; Xiong, Xinnuo; Guo, Liuqi; Wang, Lili; Li, Shanshan; Tang, Peixiao; Yan, Jin; Wu, Di; Li, Hui

2015-12-01

Levetiracetam (LEV) crystals were prepared using different solvents at different temperatures. The LEV crystals were systematically characterized by X-ray powder diffraction (XRPD) and morphological analysis. The results indicated that many kinds of crystal habits exist in a solid form of LEV. To investigate the effects of LEV concentration, crystallization temperature, and crystallization type on crystallization and solid phase transformation of LEV, multiple methods were performed for LEV aqueous solution to determine if a new solid form exists in solid-state LEV. However, XRPD data demonstrate that the LEV solid forms possess same spatial arrangements that are similar to the original solid form. This result indicates that the LEV concentration, crystallization temperature, and crystallization type in aqueous solution have no influence on the crystallization and solid phase transformation of LEV. Moreover, crystallization by sublimation, melt cooling, and quench cooling, as well as mechanical effect, did not result in the formation of new LEV solid state. During melt cooling, the transformation of solid form LEV is a direct process from melting amorphous phase to the original LEV crystal phase, and the conversion rate is very quick. In addition, stability investigation manifested that LEV solid state is very stable under various conditions. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Building of Equations of State with Numerous Phase Transitions — Application to Bismuth

NASA Astrophysics Data System (ADS)

Heuzé, Olivier

2006-07-01

We propose an algorithm to build complete equation of state EOS including several solid/solid or solid/liquid phase transitions. Each phase has its own EOS and independent parameters. The phase diagram is deduced from the thermodynamic equilibrium assumption. Until now, such an approach was used in simple cases and limited to 2 or 3 phases. We have applied it in the general case to bismuth for which up to 13 phases have been identified. This study shows the great influence of binary mixtures and triple points properties in released isentropes after shock waves.

Density-functional theory for fluid-solid and solid-solid phase transitions.

PubMed

Bharadwaj, Atul S; Singh, Yashwant

2017-03-01

We develop a theory to describe solid-solid phase transitions. The density functional formalism of classical statistical mechanics is used to find an exact expression for the difference in the grand thermodynamic potentials of the two coexisting phases. The expression involves both the symmetry conserving and the symmetry broken parts of the direct pair correlation function. The theory is used to calculate phase diagram of systems of soft spheres interacting via inverse power potentials u(r)=ε(σ/r)^{n}, where parameter n measures softness of the potential. We find that for 1/n<0.154 systems freeze into the face centered cubic (fcc) structure while for 1/n≥0.154 the body-centred-cubic (bcc) structure is preferred. The bcc structure transforms into the fcc structure upon increasing the density. The calculated phase diagram is in good agreement with the one found from molecular simulations.

Origin of the incommensurate phase of quartz: I. Inelastic neutron scattering study of the high temperature β phase of quartz

NASA Astrophysics Data System (ADS)

Dolino, G.; Berge, B.; Vallade, M.; Moussa, F.

1992-07-01

The origin of the incommensurate phase of quartz is attributed to a gradient interaction between the optical soft mode of the α-β transition of quartz and a transverse acoustic mode. To test this model high resolution inelastic neutron scattering studies of the lattice dynamics of quartz have been performed. For the first time, a resolved zone center soft mode has been observed in the β phase of quartz at 1 THz at 1 250 K, confirming the displacive character of this transition. Along [xi 0 0] a strong interaction has been observed between this soft mode and the acoustic branch with u_{xy} shear strain. The softening of the two mixed branches produced by this interaction has been followed by decreasing temperature. Near the transition a dip appears in the lower frequency branch, which goes continuously to 0 near xi=0.035 at the incommensurate phase transition. Due to a large damping, the soft branch is overdamped near the transition leading to a quasielastic peak. Along [ xi xi 0] where the soft mode is coupled with the longitudinal acoustic mode, no dip is observed in the lower frequency mode. These results are in good agreement with the predictions of the gradient interaction model discussed in the following paper. L'existence de la phase incommensurable du quartz est attribuée à une interaction entre le gradient du mode mou optique de la transition α β et un mode acoustique transverse. Pour vérifier ce modèle, des mesures de diffusion inélastique des neutrons, de haute résolution, ont été faites. Un mode mou résolu en centre de zone a, pour la première fois, été observé vers 1 THz à 1 250 K, dans la phase β du quartz, confirmant le caractère displacif de cette transition. Le long de [ xi 0 0] , une forte interaction est observée entre ce mode mou et la branche acoustique ayant une déformation de cisaillement u_{xy}. L'amollissement des deux branches mixtes, résultant de cette interaction, a été suivi en fonction de la température. Près de la transition, un minimum apparaît sur la branche basse fréquence, qui décroît continuement jusqu'à 0 pour xi=0,035 à la transition incommensurable. En raison d'un amortissement important, la branche molle est suramortie près de la transition, ce qui produit un pic quasiélastique. Le long de [xi xi 0], où le mode mou est couplé avec le mode acoustique longitudinal, aucun minimum n'est observé. Ces résultats sont en bon accord avec les prédictions du modèle de couplage avec un gradient, dèveloppé dans l'article suivant.

Two-phase anaerobic digestion of vegetable market waste fraction of municipal solid waste and development of improved technology for phase separation in two-phase reactor.

PubMed

Majhi, Bijoy Kumar; Jash, Tushar

2016-12-01

Biogas production from vegetable market waste (VMW) fraction of municipal solid waste (MSW) by two-phase anaerobic digestion system should be preferred over the single-stage reactors. This is because VMW undergoes rapid acidification leading to accumulation of volatile fatty acids and consequent low pH resulting in frequent failure of digesters. The weakest part in the two-phase anaerobic reactors was the techniques applied for solid-liquid phase separation of digestate in the first reactor where solubilization, hydrolysis and acidogenesis of solid organic waste occur. In this study, a two-phase reactor which consisted of a solid-phase reactor and a methane reactor was designed, built and operated with VMW fraction of Indian MSW. A robust type filter, which is unique in its implementation method, was developed and incorporated in the solid-phase reactor to separate the process liquid produced in the first reactor. Experiments were carried out to assess the long term performance of the two-phase reactor with respect to biogas production, volatile solids reduction, pH and number of occurrence of clogging in the filtering system or choking in the process liquid transfer line. The system performed well and was operated successfully without the occurrence of clogging or any other disruptions throughout. Biogas production of 0.86-0.889m 3 kg -1 VS, at OLR of 1.11-1.585kgm -3 d -1 , were obtained from vegetable market waste, which were higher than the results reported for similar substrates digested in two-phase reactors. The VS reduction was 82-86%. The two-phase anaerobic digestion system was demonstrated to be stable and suitable for the treatment of VMW fraction of MSW for energy generation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mechanism and microstructures in Ga2O3 pseudomartensitic solid phase transition.

PubMed

Zhu, Sheng-Cai; Guan, Shu-Hui; Liu, Zhi-Pan

2016-07-21

Solid-to-solid phase transition, although widely exploited in making new materials, challenges persistently our current theory for predicting its complex kinetics and rich microstructures in transition. The Ga2O3α-β phase transformation represents such a common but complex reaction with marked change in cation coordination and crystal density, which was known to yield either amorphous or crystalline products under different synthetic conditions. Here we, via recently developed stochastic surface walking (SSW) method, resolve for the first time the atomistic mechanism of Ga2O3α-β phase transformation, the pathway of which turns out to be the first reaction pathway ever determined for a new type of diffusionless solid phase transition, namely, pseudomartensitic phase transition. We demonstrate that the sensitivity of product crystallinity is caused by its multi-step, multi-type reaction pathway, which bypasses seven intermediate phases and involves all types of elementary solid phase transition steps, i.e. the shearing of O layers (martensitic type), the local diffusion of Ga atoms (reconstructive type) and the significant lattice dilation (dilation type). While the migration of Ga atoms across the close-packed O layers is the rate-determining step and yields "amorphous-like" high energy intermediates, the shearing of O layers contributes to the formation of coherent biphase junctions and the presence of a crystallographic orientation relation, (001)α//(201[combining macron])β + [120]α//[13[combining macron]2]β. Our experiment using high-resolution transmission electron microscopy further confirms the theoretical predictions on the atomic structure of biphase junction and the formation of (201[combining macron])β twin, and also discovers the late occurrence of lattice expansion in the nascent β phase that grows out from the parent α phase. By distinguishing pseudomartensitic transition from other types of mechanisms, we propose general rules to predict the product crystallinity of solid phase transition. The new knowledge on the kinetics of pseudomartensitic transition complements the theory of diffusionless solid phase transition.

Thermodynamic Investigation of the Effect of Interface Curvature on the Solid-Liquid Equilibrium and Eutectic Point of Binary Mixtures.

PubMed

Liu, Fanghui; Zargarzadeh, Leila; Chung, Hyun-Joong; Elliott, Janet A W

2017-10-12

Thermodynamic phase behavior is affected by curved interfaces in micro- and nanoscale systems. For example, capillary freezing point depression is associated with the pressure difference between the solid and liquid phases caused by interface curvature. In this study, the thermal, mechanical, and chemical equilibrium conditions are derived for binary solid-liquid equilibrium with a curved solid-liquid interface due to confinement in a capillary. This derivation shows the equivalence of the most general forms of the Gibbs-Thomson and Ostwald-Freundlich equations. As an example, the effect of curvature on solid-liquid equilibrium is explained quantitatively for the water/glycerol system. Considering the effect of a curved solid-liquid interface, a complete solid-liquid phase diagram is developed over a range of concentrations for the water/glycerol system (including the freezing of pure water or precipitation of pure glycerol depending on the concentration of the solution). This phase diagram is compared with the traditional phase diagram in which the assumption of a flat solid-liquid interface is made. We show the extent to which nanoscale interface curvature can affect the composition-dependent freezing and precipitating processes, as well as the change in the eutectic point temperature and concentration with interface curvature. Understanding the effect of curvature on solid-liquid equilibrium in nanoscale capillaries has applications in the food industry, soil science, cryobiology, nanoporous materials, and various nanoscience fields.

Suppressing the cellular breakdown in silicon supersaturated with titanium

NASA Astrophysics Data System (ADS)

Liu, Fang; Prucnal, S.; Hübner, R.; Yuan, Ye; Skorupa, W.; Helm, M.; Zhou, Shengqiang

2016-06-01

Hyper doping Si with up to 6 at.% Ti in solid solution was performed by ion implantation followed by pulsed laser annealing and flash lamp annealing. In both cases, the implanted Si layer can be well recrystallized by liquid phase epitaxy and solid phase epitaxy, respectively. Cross-sectional transmission electron microscopy of Ti-implanted Si after liquid phase epitaxy shows the so-called growth interface breakdown or cellular breakdown owing to the occurrence of constitutional supercooling in the melt. The appearance of cellular breakdown prevents further recrystallization. However, the out-diffusion and cellular breakdown can be effectively suppressed by solid phase epitaxy during flash lamp annealing due to the high velocity of amorphous-crystalline interface and the low diffusion velocity for Ti in the solid phase.

Comparing the catalytic oxidation of ethanol at the solid-gas and solid-liquid interfaces over size-controlled Pt nanoparticles: striking differences in kinetics and mechanism.

PubMed

Sapi, Andras; Liu, Fudong; Cai, Xiaojun; Thompson, Christopher M; Wang, Hailiang; An, Kwangjin; Krier, James M; Somorjai, Gabor A

2014-11-12

Pt nanoparticles with controlled size (2, 4, and 6 nm) are synthesized and tested in ethanol oxidation by molecular oxygen at 60 °C to acetaldehyde and carbon dioxide both in the gas and liquid phases. The turnover frequency of the reaction is ∼80 times faster, and the activation energy is ∼5 times higher at the gas-solid interface compared to the liquid-solid interface. The catalytic activity is highly dependent on the size of the Pt nanoparticles; however, the selectivity is not size sensitive. Acetaldehyde is the main product in both media, while twice as much carbon dioxide was observed in the gas phase compared to the liquid phase. Added water boosts the reaction in the liquid phase; however, it acts as an inhibitor in the gas phase. The more water vapor was added, the more carbon dioxide was formed in the gas phase, while the selectivity was not affected by the concentration of the water in the liquid phase. The differences in the reaction kinetics of the solid-gas and solid-liquid interfaces can be attributed to the molecular orientation deviation of the ethanol molecules on the Pt surface in the gas and liquid phases as evidenced by sum frequency generation vibrational spectroscopy.

Characterisation of Fibre Reinforced Titanium Matrix Composites. (La Caracterisation des Materiaux Composites a Matrice de Titane Renforces par Fibres)

DTIC Science & Technology

1994-02-01

devait servir de forum pour un 6change d’informations sur ce sujet important. Dans ce cas. [a caracterisation se ref~re A l’analyse du comportement des...phases de d~veloppement et de mise a l’echelle. mais aussi aux activites de caracterisation et de demonstration des composants. Dans le cas des materiaux

Laboratory Layered Latte

NASA Astrophysics Data System (ADS)

Xue, Nan; Khodaparast, Sepideh; Zhu, Lailai; Nunes, Janine; Kim, Hyoungsoo; Stone, Howard

2017-11-01

Layered composite fluids are sometimes observed in confined systems of rather chaotic initial states, for example, layered lattes formed by pouring espresso into a glass of warm milk. In such configurations, pouring forces a lower density liquid (espresso) into a higher density ambient, which is similar to the fountain effects that characterize a wide range of flows driven by injecting a fluid into a second miscible phase. Although the initial state of the mixture is complex and chaotic, there are conditions where the mixture cools at room temperature and exhibits an organized layered pattern. Here we report controlled experiments injecting a fluid into a miscible phase and show that, above a critical injection velocity, layering naturally emerges over the time scale of minutes. We perform experimental and numerical analyses of the time-dependent flows to observe and understand the convective circulation in the layers. We identify critical conditions to produce the layering and relate the results quantitatively to the critical Rayleigh number in double-diffusive convection, which indicates the competition between the horizontal thermal gradient and the vertical density gradient generated by the fluid injection. Based on this understanding, we show how to employ this single-step process to produce layered structures in soft materials, where the local elastic properties as well as the local material concentration vary step-wise along the length of the material.

Simulation of the as-cast structure of Al-4.0wt.%Cu ingots with a 5-phase mixed columnar-equiaxed solidification model

NASA Astrophysics Data System (ADS)

Wu, M.; Ahmadein, M.; Kharicha, A.; Ludwig, A.; Li, J. H.; Schumacher, P.

2012-07-01

Empirical knowledge about the formation of the as-cast structure, mostly obtained before 1980s, has revealed two critical issues: one is the origin of the equiaxed crystals; one is the competing growth of the columnar and equiaxed structures, and the columnar-to-equiaxed transition (CET). Unfortunately, the application of empirical knowledge to predict and control the as-cast structure was very limited, as the flow and crystal transport were not considered. Therefore, a 5-phase mixed columnar-equiaxed solidification model was recently proposed by the current authors based on modeling the multiphase transport phenomena. The motivation of the recent work is to determine and evaluate the necessary modeling parameters, and to validate the mixed columnar-equiaxed solidification model by comparison with laboratory castings. In this regard an experimental method was recommended for in-situ determination of the nucleation parameters. Additionally, some classical experiments of the Al-Cu ingots were conducted and the as-cast structural information including distinct columnar and equiaxed zones, macrosegregation, and grain size distribution were analysed. The final simulation results exhibited good agreement with experiments in the case of high pouring temperature, whereas disagreement in the case of low pouring temperature. The reasons for the disagreement are discussed.

A High-Throughput Process for the Solid-Phase Purification of Synthetic DNA Sequences

PubMed Central

Grajkowski, Andrzej; Cieślak, Jacek; Beaucage, Serge L.

2017-01-01

An efficient process for the purification of synthetic phosphorothioate and native DNA sequences is presented. The process is based on the use of an aminopropylated silica gel support functionalized with aminooxyalkyl functions to enable capture of DNA sequences through an oximation reaction with the keto function of a linker conjugated to the 5′-terminus of DNA sequences. Deoxyribonucleoside phosphoramidites carrying this linker, as a 5′-hydroxyl protecting group, have been synthesized for incorporation into DNA sequences during the last coupling step of a standard solid-phase synthesis protocol executed on a controlled pore glass (CPG) support. Solid-phase capture of the nucleobase- and phosphate-deprotected DNA sequences released from the CPG support is demonstrated to proceed near quantitatively. Shorter than full-length DNA sequences are first washed away from the capture support; the solid-phase purified DNA sequences are then released from this support upon reaction with tetra-n-butylammonium fluoride in dry dimethylsulfoxide (DMSO) and precipitated in tetrahydrofuran (THF). The purity of solid-phase-purified DNA sequences exceeds 98%. The simulated high-throughput and scalability features of the solid-phase purification process are demonstrated without sacrificing purity of the DNA sequences. PMID:28628204

Nanostructured lipid carriers: effect of solid phase fraction and distribution on the release of encapsulated materials.

PubMed

Dan, Nily

2014-11-25

Emulsions, solid lipid nanoparticles (SLN), and nanostructured lipid carriers (NLC) containing a mix of liquid and solid domains are of interest as encapsulation vehicles for hydrophobic compounds. Studies of the release rate from these particles yield contradictory results: Some find that increasing the fraction of solid phase increases the rate of release and others the opposite. In this paper we study the release of encapsulated materials from lipid-based nanoparticles using Monte Carlo simulations. We find that, quite surprisingly, the release rate is largely insensitive to the size of solid domains or the fraction of solid phase. However, the distribution of the domains significantly affects the rate of release: Solid domains located at the interface with the surrounding solution inhibit transport, while nanoparticles where the solid domains are concentrated in the center enhance it. The latter can lead to release rates in NLCs that are faster than in the equivalent emulsions. We conclude that controlling the release rate from NLCs requires the ability to determine the location and distribution of the solid phase, which may be achieved through choice of the surfactants stabilizing the particles, incorporation of nucleation sites, and/or the cooling rates and temperatures.

Solid phase stability of molybdenum under compression: Sound velocity measurements and first-principles calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Xiulu; Laboratory for Extreme Conditions Matter Properties, Southwest University of Science and Technology, 621010 Mianyang, Sichuan; Liu, Zhongli

2015-02-07

The high-pressure solid phase stability of molybdenum (Mo) has been the center of a long-standing controversy on its high-pressure melting. In this work, experimental and theoretical researches have been conducted to check its solid phase stability under compression. First, we performed sound velocity measurements from 38 to 160 GPa using the two-stage light gas gun and explosive loading in backward- and forward-impact geometries, along with the high-precision velocity interferometry. From the sound velocities, we found no solid-solid phase transition in Mo before shock melting, which does not support the previous solid-solid phase transition conclusion inferred from the sharp drops of themore » longitudinal sound velocity [Hixson et al., Phys. Rev. Lett. 62, 637 (1989)]. Then, we searched its structures globally using the multi-algorithm collaborative crystal structure prediction technique combined with the density functional theory. By comparing the enthalpies of body centered cubic structure with those of the metastable structures, we found that bcc is the most stable structure in the range of 0–300 GPa. The present theoretical results together with previous ones greatly support our experimental conclusions.« less

Communication: phase transitions, criticality, and three-phase coexistence in constrained cell models.

PubMed

Nayhouse, Michael; Kwon, Joseph Sang-Il; Orkoulas, G

2012-05-28

In simulation studies of fluid-solid transitions, the solid phase is usually modeled as a constrained system in which each particle is confined to move in a single Wigner-Seitz cell. The constrained cell model has been used in the determination of fluid-solid coexistence via thermodynamic integration and other techniques. In the present work, the phase diagram of such a constrained system of Lennard-Jones particles is determined from constant-pressure simulations. The pressure-density isotherms exhibit inflection points which are interpreted as the mechanical stability limit of the solid phase. The phase diagram of the constrained system contains a critical and a triple point. The temperature and pressure at the critical and the triple point are both higher than those of the unconstrained system due to the reduction in the entropy caused by the single occupancy constraint.

Modeling of Shock Waves with Multiple Phase Transitions in Condensed Materials

NASA Astrophysics Data System (ADS)

Missonnier, Marc; Heuzé, Olivier

2006-07-01

When a shock wave crosses a solid material and subjects it to solid-solid or solid-liquid phase transition, related phenomena occur: shock splitting, and the corresponding released shock wave after reflection. Modelling of these phenomena raises physical and numerical issues. After shock loading, such materials can reach different kinds of states: single-phase states, binary-phase states, and triple points. The thermodynamic path can be studied and easily understood in the (V,E) or (V,S) planes. In the case of 3 phase tin (β,γ, and liquid) submitted to shock waves, seven states can occur: β,γ, liquid, β-γ, β-liquid, γ-liquid, and β-γ-liquid. After studying the thermodynamic properties with a complete 3-phase Equation of State, we show the existence of these seven states with a hydrodynamic simulation.

Optimization of the β-Elimination/Michael Addition Chemistry on Reversed-Phase Supports for Mass Spectrometry Analysis of O-Linked Protein Modifications

PubMed Central

Nika, Heinz; Nieves, Edward; Hawke, David H.; Angeletti, Ruth Hogue

2013-01-01

We previously adapted the β-elimination/Michael addition chemistry to solid-phase derivatization on reversed-phase supports, and demonstrated the utility of this reaction format to prepare phosphoseryl peptides in unfractionated protein digests for mass spectrometric identification and facile phosphorylation-site determination. Here, we have expanded the use of this technique to β-N-acetylglucosamine peptides, modified at serine/threonine, phosphothreonyl peptides, and phosphoseryl/phosphothreonyl peptides, followed in sequence by proline. The consecutive β-elimination with Michael addition was adapted to optimize the solid-phase reaction conditions for throughput and completeness of derivatization. The analyte remained intact during derivatization and was recovered efficiently from the silica-based, reversed-phase support with minimal sample loss. The general use of the solid-phase approach for enzymatic dephosphorylation was demonstrated with phosphoseryl and phosphothreonyl peptides and was used as an orthogonal method to confirm the identity of phosphopeptides in proteolytic mixtures. The solid-phase approach proved highly suitable to prepare substrates from low-level amounts of protein digests for phosphorylation-site determination by chemical-targeted proteolysis. The solid-phase protocol provides for a simple, robust, and efficient tool to prepare samples for phosphopeptide identification in MALDI mass maps of unfractionated protein digests, using standard equipment available in most biological laboratories. The use of a solid-phase analytical platform is expected to be readily expanded to prepare digest from O-glycosylated- and O-sulfonated proteins for mass spectrometry-based structural characterization. PMID:23997661

Equations of State and Phase Diagrams of Ammonia

ERIC Educational Resources Information Center

Glasser, Leslie

2009-01-01

We present equations of state relating the phases and a three-dimensional phase diagram for ammonia with its solid, liquid, and vapor phases, based on fitted authentic experimental data and including recent information on the high-pressure solid phases. This presentation follows similar articles on carbon dioxide and water published in this…

Molecular orientation of organic thin films on dielectric solid substrates: a phase-sensitive vibrational SFG study.

PubMed

Ge, Aimin; Peng, Qiling; Qiao, Lin; Yepuri, Nageshwar R; Darwish, Tamim A; Matsusaki, Michiya; Akashi, Mitsuru; Ye, Shen

2015-07-21

Broadband phase-sensitive vibrational sum frequency generation (SFG) spectroscopy was utilized to study the molecular orientation of molecules adsorbed on dielectric solid substrates. A gold thin film was employed to generate a SFG signal as a local oscillator (LO). To simplify the phase measurement, a self-assembled monolayer (SAM) of octadecyltrichlorosilane (OTS) was used as a standard sample for phase correction of the phase-sensitive SFG measurements on the solid/air interface. It was demonstrated that the absolute orientation of molecules in the LB films on a fused quartz surface can be clearly distinguished by phase-sensitive SFG measurement. In addition, the observation on the SAM of d35-OTS reveals that the two C-H stretching modes for α-CH2 group are in opposite phase. Furthermore, by using the present phase-sensitive SFG setup, the orientation flipping of water molecules on positively and negatively charged solid/liquid interface can be distinguished.

Numerical Computation of Flame Spread over a Thin Solid in Forced Concurrent Flow with Gas-phase Radiation

NASA Technical Reports Server (NTRS)

Jiang, Ching-Biau; T'ien, James S.

1994-01-01

Excerpts from a paper describing the numerical examination of concurrent-flow flame spread over a thin solid in purely forced flow with gas-phase radiation are presented. The computational model solves the two-dimensional, elliptic, steady, and laminar conservation equations for mass, momentum, energy, and chemical species. Gas-phase combustion is modeled via a one-step, second order finite rate Arrhenius reaction. Gas-phase radiation considering gray non-scattering medium is solved by a S-N discrete ordinates method. A simplified solid phase treatment assumes a zeroth order pyrolysis relation and includes radiative interaction between the surface and the gas phase.

Phase III gross solids removal devices pilot study, 2002-2005.

DOT National Transportation Integrated Search

2005-12-01

The objective of the Phase III Gross Solids Removal Devices (GSRDs) Pilot study was to : evaluate the performance of non-proprietary devices that can capture gross solids and that can be : incorporated into existing highway drainage systems or implem...

Three-phase boundary length in solid-oxide fuel cells: A mathematical model

NASA Astrophysics Data System (ADS)

Janardhanan, Vinod M.; Heuveline, Vincent; Deutschmann, Olaf

A mathematical model to calculate the volume specific three-phase boundary length in the porous composite electrodes of solid-oxide fuel cell is presented. The model is exclusively based on geometrical considerations accounting for porosity, particle diameter, particle size distribution, and solids phase distribution. Results are presented for uniform particle size distribution as well as for non-uniform particle size distribution.

Quick, easy, cheap, effective, rugged, and safe sample preparation approach for pesticide residue analysis using traditional detectors in chromatography: A review.

PubMed

Rahman, Md Musfiqur; Abd El-Aty, A M; Kim, Sung-Woo; Shin, Sung Chul; Shin, Ho-Chul; Shim, Jae-Han

2017-01-01

In pesticide residue analysis, relatively low-sensitivity traditional detectors, such as UV, diode array, electron-capture, flame photometric, and nitrogen-phosphorus detectors, have been used following classical sample preparation (liquid-liquid extraction and open glass column cleanup); however, the extraction method is laborious, time-consuming, and requires large volumes of toxic organic solvents. A quick, easy, cheap, effective, rugged, and safe method was introduced in 2003 and coupled with selective and sensitive mass detectors to overcome the aforementioned drawbacks. Compared to traditional detectors, mass spectrometers are still far more expensive and not available in most modestly equipped laboratories, owing to maintenance and cost-related issues. Even available, traditional detectors are still being used for analysis of residues in agricultural commodities. It is widely known that the quick, easy, cheap, effective, rugged, and safe method is incompatible with conventional detectors owing to matrix complexity and low sensitivity. Therefore, modifications using column/cartridge-based solid-phase extraction instead of dispersive solid-phase extraction for cleanup have been applied in most cases to compensate and enable the adaptation of the extraction method to conventional detectors. In gas chromatography, the matrix enhancement effect of some analytes has been observed, which lowers the limit of detection and, therefore, enables gas chromatography to be compatible with the quick, easy, cheap, effective, rugged, and safe extraction method. For liquid chromatography with a UV detector, a combination of column/cartridge-based solid-phase extraction and dispersive solid-phase extraction was found to reduce the matrix interference and increase the sensitivity. A suitable double-layer column/cartridge-based solid-phase extraction might be the perfect solution, instead of a time-consuming combination of column/cartridge-based solid-phase extraction and dispersive solid-phase extraction. Therefore, replacing dispersive solid-phase extraction with column/cartridge-based solid-phase extraction in the cleanup step can make the quick, easy, cheap, effective, rugged, and safe extraction method compatible with traditional detectors for more sensitive, effective, and green analysis. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Neutronic Program for Critical and Nonequilibrium Study of Mobile Fuel Reactors: The Cinsf1D Code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lecarpentier, David; Carpentier, Vincent

2003-01-15

Molten salt reactors (MSRs) have the distinction of having a liquid fuel that is also the coolant. The transport of delayed-neutron precursors by the fuel modifies the precursors' equation. As a consequence, it is necessary to adapt the methods currently used for solid fuel reactors to achieve critical or kinetics calculations for an MSR. A program is presented for which this adaptation has been carried out within the framework of the two-energy-group diffusion theory with one dimension of space. This program has been called Cinsf1D (Cinetique pour reacteur a sels fondus 1D)

Simultaneous estimation of liquid and solid gastric emptying using radiolabelled egg and water in supine normal subjects.

PubMed

Kris, M G; Yeh, S D; Gralla, R J; Young, C W

1986-01-01

To develop an additional method for the measurement of gastric emptying in supine subjects, 10 normal subjects were given a test meal containing 99Tc-labelled scrambled egg as the "solid" phase marker and 111In in tapwater as the marker for the "liquid" phase. The mean time for emptying 50% of the "solid" phase (t1/2) was 85 min and 29 min for the "liquid" phase. Three individuals were restudied with a mean difference between the two determinations of 10.8% for the "solid" phase and 6.5% for the "liquid" phase. Twenty-six additional studies attempted have been successfully completed in symptomatic patients with advanced cancer. This method provides a simple and reproducible procedure for the determination of gastric emptying that yields results similar to those reported for other test meals and can be used in debilitated patients.

Thermal shock resistance ceramic insulator

DOEpatents

Morgan, Chester S.; Johnson, William R.

1980-01-01

Thermal shock resistant cermet insulators containing 0.1-20 volume % metal present as a dispersed phase. The insulators are prepared by a process comprising the steps of (a) providing a first solid phase mixture of a ceramic powder and a metal precursor; (b) heating the first solid phase mixture above the minimum decomposition temperature of the metal precursor for no longer than 30 minutes and to a temperature sufficiently above the decomposition temperature to cause the selective decomposition of the metal precursor to the metal to provide a second solid phase mixture comprising particles of ceramic having discrete metal particles adhering to their surfaces, said metal particles having a mean diameter no more than 1/2 the mean diameter of the ceramic particles, and (c) densifying the second solid phase mixture to provide a cermet insulator having 0.1-20 volume % metal present as a dispersed phase.

Phase IV gross solids removal devices pilot study, 2004-2005.

DOT National Transportation Integrated Search

2005-12-01

The objective of the Phase IV Gross Solids Removal Device (GSRD) Pilot study was to evaluate : the performance of one non-proprietary device that can capture gross solids and that can be : incorporated into existing highway drainage systems or implem...

Characterization of the Solid-Phase Behavior of n-Nonylammonium Tetrachlorocuprate by Fourier Transform Infrared Spectroscopy

NASA Astrophysics Data System (ADS)

Ning, Guo

1995-06-01

The solid-phase behavior of [n-C9H19NH3]2CuCl4 was investigated by infrared spectroscopy. The nature of the three solid phases (phase I, phase II, and phase III) is discussed. A temperature-dependent study of infrared spectra provides evidence for the occurrence of structural phase transitions related to the dynamics of the alkyl chains and -NH3 polar heads. The phase transition at Tc1 (22°C) arises from variation in the interaction and packing structure of the chain. The phase transition at Tc2 (34°C) is related to variation in partial conformational order-disorder at the intramolecular level. The GTG or GTG‧ and small concentration of TG structures near the CH3 group are generated in phase III (above 38°C).

Role of Precursor-Conversion Chemistry in the Crystal-Phase Control of Catalytically Grown Colloidal Semiconductor Quantum Wires.

PubMed

Wang, Fudong; Buhro, William E

2017-12-26

Crystal-phase control is one of the most challenging problems in nanowire growth. We demonstrate that, in the solution-phase catalyzed growth of colloidal cadmium telluride (CdTe) quantum wires (QWs), the crystal phase can be controlled by manipulating the reaction chemistry of the Cd precursors and tri-n-octylphosphine telluride (TOPTe) to favor the production of either a CdTe solute or Te, which consequently determines the composition and (liquid or solid) state of the Bi x Cd y Te z catalyst nanoparticles. Growth of single-phase (e.g., wurtzite) QWs is achieved only from solid catalysts (y ≪ z) that enable the solution-solid-solid growth of the QWs, whereas the liquid catalysts (y ≈ z) fulfill the solution-liquid-solid growth of the polytypic QWs. Factors that affect the precursor-conversion chemistry are systematically accounted for, which are correlated with a kinetic study of the composition and state of the catalyst nanoparticles to understand the mechanism. This work reveals the role of the precursor-reaction chemistry in the crystal-phase control of catalytically grown colloidal QWs, opening the possibility of growing phase-pure QWs of other compositions.

Solid-liquid critical behavior of water in nanopores.

PubMed

Mochizuki, Kenji; Koga, Kenichiro

2015-07-07

Nanoconfined liquid water can transform into low-dimensional ices whose crystalline structures are dissimilar to any bulk ices and whose melting point may significantly rise with reducing the pore size, as revealed by computer simulation and confirmed by experiment. One of the intriguing, and as yet unresolved, questions concerns the observation that the liquid water may transform into a low-dimensional ice either via a first-order phase change or without any discontinuity in thermodynamic and dynamic properties, which suggests the existence of solid-liquid critical points in this class of nanoconfined systems. Here we explore the phase behavior of a model of water in carbon nanotubes in the temperature-pressure-diameter space by molecular dynamics simulation and provide unambiguous evidence to support solid-liquid critical phenomena of nanoconfined water. Solid-liquid first-order phase boundaries are determined by tracing spontaneous phase separation at various temperatures. All of the boundaries eventually cease to exist at the critical points and there appear loci of response function maxima, or the Widom lines, extending to the supercritical region. The finite-size scaling analysis of the density distribution supports the presence of both first-order and continuous phase changes between solid and liquid. At around the Widom line, there are microscopic domains of two phases, and continuous solid-liquid phase changes occur in such a way that the domains of one phase grow and those of the other evanesce as the thermodynamic state departs from the Widom line.

Comparison of solid-phase and eluate assays to gauge the ecotoxicological risk of organic wastes on soil organisms.

PubMed

Domene, Xavier; Alcañiz, Josep M; Andrés, Pilar

2008-02-01

Development of methodologies to assess the safety of reusing polluted organic wastes in soil is a priority in Europe. In this study, and coupled with chemical analysis, seven organic wastes were subjected to different aquatic and soil bioassays. Tests were carried out with solid-phase waste and three different waste eluates (water, methanol, and dichloromethane). Solid-phase assays were indicated as the most suitable for waste testing not only in terms of relevance for real situations, but also because toxicity in eluates was generally not representative of the chronic effects in solid-phase. No general correlations were found between toxicity and waste pollutant burden, neither in solid-phase nor in eluate assays, showing the inability of chemical methods to predict the ecotoxicological risks of wastes. On the contrary, several physicochemical parameters reflecting the degree of low organic matter stability in wastes were the main contributors to the acute toxicity seen in collembolans and daphnids.

Solid-Phase Radioimmunoassay of Total and Influenza-Specific Immunoglobulin G

PubMed Central

Daugharty, Harry; Warfield, Donna T.; Davis, Marianne L.

1972-01-01

An antigen-antibody system of polystyrene tubes coated with immunoglobulin antibody was used for quantitating immunoglobulins. A similar radioimmunoassay method was adapted for a viral antigen-antibody system. The viral system can be used for quantitating viruses and for measuring virus-specific antibodies by reacting with 125iodine-labeled anti-immunoglobulin G (IgG). Optimal conditions for coating the solid phase, specificity of the immune reaction, and other kinetics and sensitivities of the assay method were investigated. Comparison of direct and indirect methods of assaying for immunoglobulins or viral antibody indicates that the indirect method is more sensitive and can quantitate a minimum of 0.037 μg of IgG per ml. Results of solid-phase radioimmunoassay for influenza antibody correlate well with hemagglutinin antibody titers but not with complement-fixing antibody titers. Radioimmunoassay results for influenza antibody by solid phase are likewise in agreement with results by the carrier precipitate radioimmunoassay method. The simplicity, reproducibility, and versatility of the solid-phase procedure make it diagnostically useful. PMID:5062884

Molecular Simulation of the Free Energy for the Accurate Determination of Phase Transition Properties of Molecular Solids

NASA Astrophysics Data System (ADS)

Sellers, Michael; Lisal, Martin; Brennan, John

2015-06-01

Investigating the ability of a molecular model to accurately represent a real material is crucial to model development and use. When the model simulates materials in extreme conditions, one such property worth evaluating is the phase transition point. However, phase transitions are often overlooked or approximated because of difficulty or inaccuracy when simulating them. Techniques such as super-heating or super-squeezing a material to induce a phase change suffer from inherent timescale limitations leading to ``over-driving,'' and dual-phase simulations require many long-time runs to seek out what frequently results in an inexact location of phase-coexistence. We present a compilation of methods for the determination of solid-solid and solid-liquid phase transition points through the accurate calculation of the chemical potential. The methods are applied to the Smith-Bharadwaj atomistic potential's representation of cyclotrimethylene trinitramine (RDX) to accurately determine its melting point (Tm) and the alpha to gamma solid phase transition pressure. We also determine Tm for a coarse-grain model of RDX, and compare its value to experiment and atomistic counterpart. All methods are employed via the LAMMPS simulator, resulting in 60-70 simulations that total 30-50 ns. Approved for public release. Distribution is unlimited.

Phase transition thermodynamics of bisphenols.

PubMed

Costa, José C S; Dávalos, Juan Z; Santos, Luís M N B F

2014-10-16

Herein we have studied, presented, and analyzed the phase equilibria thermodynamics of a bisphenols (BP-A, BP-E, BP-F, BP-AP, and BP-S) series. In particular, the heat capacities, melting temperatures, and vapor pressures at different temperatures as well as the standard enthalpies, entropies, and Gibbs energies of phase transition (fusion and sublimation) were experimentally determined. Also, we have presented the phase diagrams of each bisphenol derivative and investigated the key parameters related to the thermodynamic stability of the condensed phases. When all the bisphenol derivatives are compared at the same conditions, solids BP-AP and BP-S present lower volatilities (higher Gibbs energy of sublimation) and high melting temperatures due to the higher stability of their solid phases. Solids BP-A and BP-F present similar stabilities, whereas BP-E is more volatile. The introduction of -CH3 groups in BP-F (giving BP-E and BP-A) leads an entropic differentiation in the solid phase, whereas in the isotropic liquids the enthalpic and entropic differentiations are negligible.

Analysis of Explosives in Soil Using Solid Phase Microextraction and Gas Chromatography: Environmental Analysis

DTIC Science & Technology

2006-01-01

ENVIRONMENTAL ANALYSIS Analysis of Explosives in Soil Using Solid Phase Microextraction and Gas Chromatography Howard T. Mayfield Air Force Research...Abstract: Current methods for the analysis of explosives in soils utilize time consuming sample preparation workups and extractions. The method detection...chromatography/mass spectrometry to provide a con- venient and sensitive analysis method for explosives in soil. Keywords: Explosives, TNT, solid phase

Binary Solid-Liquid Phase Equilibria

ERIC Educational Resources Information Center

Ellison, Herbert R.

1978-01-01

Indicates some of the information that may be obtained from a binary solid-liquid phase equilibria experiment and a method to write a computer program that will plot an ideal phase diagram to which the experimental results may be compared. (Author/CP)

Role of lattice distortion on diffuse phase transition temperatures in Bi0.5Na0.5TiO3-BaTiO3 [BNBTO] solid solutions

NASA Astrophysics Data System (ADS)

Pradhan, Lagen Kumar; Pandey, Rabichandra; Kumar, Sunil; Supriya, Sweety; Kar, Manoranjan

2018-04-01

Effect of lattice distortion on diffuse phase transition in BNBTO solid solutions near Morphotropic phase boundary (MPB) has been investigated. Solid solutions of (Bi0.5Na0.5)1-xBaxTiO3 (with mole % of x= 0.04, 0.05, 0.06, 0.07 and 0.08) were prepared by the planetary ball mill method in ethanol medium. Rietveld refinement technique with rhombohedral (R3c) and tetragonal (P4bm) crystal symmetry has been employed for structural as well as phase analysis of the solid solutions. Both rhombohedral and tetragonal lattice distortion (c/a) tends toward the pseudo-cubic crystal symmetry with the increase of mole fraction of Ba2+ near MPB (x= 6 mole %). Also, the average crystallite size and grain size decrease with increase of mole fraction of Ba2+ in BNT ceramic are due to larger ionic radius of Ba2+ and grain boundary pinning process in the solid solutions respectively. Additionally, depolarization temperature (Td) and maximum temperature (Tm) reduces due to the lattice distortion of both the phases in BNBTO solid solutions, which is explained extensively. Significant increase of dielectric constant has been observed near MPB composition (x=6%) in BNBTO solid solutions.

Influence of calcium on microbial reduction of solid phase uranium(VI).

PubMed

Liu, Chongxuan; Jeon, Byong-Hun; Zachara, John M; Wang, Zheming

2007-08-15

The effect of calcium on the dissolution and microbial reduction of a representative solid phase uranyl [U(VI)], sodium boltwoodite (NaUO(2)SiO(3)OH . 1.5H(2)O), was investigated to evaluate the rate-limiting step of microbial reduction of the solid phase U(VI). Microbial reduction experiments were performed in a culture of a dissimilatory metal-reducing bacterium (DMRB), Shewanella oneidensis strain MR-1, in a bicarbonate medium with lactate as electron donor at pH 6.8 buffered with PIPES. Calcium increased the rate of Na-boltwoodite dissolution and U(VI) bioavailability by increasing its solubility through the formation of a ternary aqueous calcium-uranyl-carbonate species. The ternary species, however, decreased the rates of microbial reduction of aqueous U(VI). Laser-induced fluorescence spectroscopy (LIFS) and transmission electron microscopy (TEM) collectively revealed that microbial reduction of solid phase U(VI) was a sequentially coupled process of Na-boltwoodite dissolution, U(VI) aqueous speciation, and microbial reduction of dissolved U(VI) to U(IV) that accumulated on bacterial surfaces/periplasm. Under studied experimental conditions, the overall rate of microbial reduction of solid phase U(VI) was limited by U(VI) dissolution reactions in solutions without calcium and limited by microbial reduction in solutions with calcium. Generally, the overall rate of microbial reduction of solid phase U(VI) was determined by the coupling of solid phase U(VI) dissolution, U(VI) aqueous speciation, and microbial reduction of dissolved U(VI) that were all affected by calcium. (c) 2007 Wiley Periodicals, Inc.

Comparison of the solid-phase fragment condensation and phase-change approaches in the synthesis of salmon I calcitonin.

PubMed

Gatos, D; Tzavara, C

2001-02-01

Salmon I calcitonin was synthesized using both phase-change and conventional solid-phase fragment condensation (SPFC) approaches, utilizing the Rink amide linker (Fmoc-amido-2,4-dimethoxybenzyl-4-phenoxyacetic acid) combined with 2-chlorotrityl resin and the Fmoc/tBu(Trt)-based protection scheme. Phase-change synthesis, performed by the selective detachment of the fully protected C-terminal 22-mer peptide-linker from the resin and subsequent condensation in solution with the N-terminal 1-10 fragment, gave a product of slightly less purity (85 vs. 92%) than the corresponding synthesis on the solid-phase. In both cases salmon I calcitonin was easily obtained in high purity.

Open-Label, Multicenter, Phase 1/2 Study of Tazemetostat (EZH2 Histone Methyl Transferase [HMT] Inhibitor) as a Single Agent in Subjects With Adv. Solid Tumors or With B-cell Lymphomas and Tazemetostat in Combination With Prednisolone in Subjects With DLBCL

ClinicalTrials.gov

2018-05-31

B-cell Lymphomas (Phase 1); Advanced Solid Tumors (Phase 1); Diffuse Large B-cell Lymphoma (Phase 2); Follicular Lymphoma (Phase 2); Transformed Follicular Lymphoma; Primary Mediastinal Large B-Cell Lymphoma

The major volume /density/ of solid oxygen in equilibrium with vapor

NASA Technical Reports Server (NTRS)

Roder, H. M.

1979-01-01

Data from the literature on the molar volume of solid oxygen have been compiled and critically analyzed. A correlated and thermodynamically consistent set of molar volumes, including the volume changes at the various solid phase transitions, is presented. Evidence for the existence of a delta-solid phase is reviewed. Uncertainties in the data and in the recommended set of values are discussed.

Solid - solid and solid - liquid phase transitions of iron and iron alloys under laser shock compression

NASA Astrophysics Data System (ADS)

Harmand, M.; Krygier, A.; Appel, K.; Galtier, E.; Hartley, N.; Konopkova, Z.; Lee, H. J.; McBride, E. E.; Miyanishi, K.; Nagler, B.; Nemausat, R.; Vinci, T.; Zhu, D.; Ozaki, N.; Fiquet, G.

2017-12-01

An accurate knowledge of the properties of iron and iron alloys at high pressures and temperatures is crucial for understanding and modelling planetary interiors. While Earth-size and Super-Earth Exoplanets are being discovered in increasingly large numbers, access to detailed information on liquid properties, melting curves and even solid phases of iron and iron at the pressures and temperatures of their interiors is still strongly limited. In this context, XFEL sources coupled with high-energy lasers afford unique opportunities to measure microscopic structural properties at far extreme conditions. Also the achievable time resolution allows the shock history and phase transition mechanisms to be followed during laser compression, improving our understanding of the high pressure and high strain experiments. Here we present recent studies devoted to investigate the solid-solid and solid-liquid transition in laser-shocked iron and iron alloys (Fe-Si, Fe-C and Fe-O alloys) using X-ray diffraction and X-ray diffuse scattering. Experiment were performed at the MEC end-station of the LCLS facility at SLAC (USA). Detection of the diffuse scattering allowed the identification of the first liquid peak position along the Hugoniot, up to 4 Mbar. The time resolution shows ultrafast (between several tens and several hundreds of picoseconds) solid-solid and solid-liquid phase transitions. Future developments at XFEL facilities will enable detailed studies of the solid and liquid structures of iron and iron alloys as well as out-of-Hugoniot studies.

A novel mechanical model for phase-separation in debris flows

NASA Astrophysics Data System (ADS)

Pudasaini, Shiva P.

2015-04-01

Understanding the physics of phase-separation between solid and fluid phases as a two-phase mass moves down slope is a long-standing challenge. Here, I propose a fundamentally new mechanism, called 'separation-flux', that leads to strong phase-separation in avalanche and debris flows. This new model extends the general two-phase debris flow model (Pudasaini, 2012) to include a separation-flux mechanism. The new flux separation mechanism is capable of describing and controlling the dynamically evolving phase-separation, segregation, and/or levee formation in a real two-phase, geometrically three-dimensional debris flow motion and deposition. These are often observed phenomena in natural debris flows and industrial processes that involve the transportation of particulate solid-fluid mixture material. The novel separation-flux model includes several dominant physical and mechanical aspects that result in strong phase-separation (segregation). These include pressure gradients, volume fractions of solid and fluid phases and their gradients, shear-rates, flow depth, material friction, viscosity, material densities, boundary structures, gravity and topographic constraints, grain shape, size, etc. Due to the inherent separation mechanism, as the mass moves down slope, more and more solid particles are brought to the front, resulting in a solid-rich and mechanically strong frontal surge head followed by a weak tail largely consisting of the viscous fluid. The primary frontal surge head followed by secondary surge is the consequence of the phase-separation. Such typical and dominant phase-separation phenomena are revealed here for the first time in real two-phase debris flow modeling and simulations. However, these phenomena may depend on the bulk material composition and the applied forces. Reference: Pudasaini, Shiva P. (2012): A general two-phase debris flow model. J. Geophys. Res., 117, F03010, doi: 10.1029/2011JF002186.

Estrogenic and AhR activities in dissolved phase and suspended solids from wastewater treatment plants.

PubMed

Dagnino, Sonia; Gomez, Elena; Picot, Bernadette; Cavaillès, Vincent; Casellas, Claude; Balaguer, Patrick; Fenet, Hélène

2010-05-15

The distribution of estrogen receptor (ERalpha) and Aryl Hydrocarbon Receptor (AhR) activities between the dissolved phase and suspended solids were investigated during wastewater treatment. Three wastewater treatment plants with different treatment technologies (waste stabilization ponds (WSPs), trickling filters (TFs) and activated sludge supplemented with a biofilter system (ASB)) were sampled. Estrogenic and AhR activities were detected in both phases in influents and effluents. Estrogenic and AhR activities in wastewater influents ranged from 41.8 to 79 ng/L E(2) Eq. and from 37.9 to 115.5 ng/L TCDD Eq. in the dissolved phase and from 5.5 to 88.6 ng/g E(2) Eq. and from 15 to 700 ng/g TCDD Eq. in the suspended solids. For both activities, WSP showed greater or similar removal efficiency than ASB and both were much more efficient than TF which had the lowest removal efficiency. Moreover, our data indicate that the efficiency of removal of ER and AhR activities from the suspended solid phase was mainly due to removal of suspended solids. Indeed, ER and AhR activities were detected in the effluent suspended solid phase indicating that suspended solids, which are usually not considered in these types of studies, contribute to environmental contamination by endocrine disrupting compounds and should therefore be routinely assessed for a better estimation of the ER and AhR activities released in the environment. Copyright 2010 Elsevier B.V. All rights reserved.

Hydrothermal carbonization of food waste for nutrient recovery and reuse.

PubMed

Idowu, Ifeolu; Li, Liang; Flora, Joseph R V; Pellechia, Perry J; Darko, Samuel A; Ro, Kyoung S; Berge, Nicole D

2017-11-01

Food waste represents a rather large and currently underutilized source of potentially available and reusable nutrients. Laboratory-scale experiments evaluating the hydrothermal carbonization of food wastes collected from restaurants were conducted to understand how changes in feedstock composition and carbonization process conditions influence primary and secondary nutrient fate. Results from this work indicate that at all evaluated reaction times and temperatures, the majority of nitrogen, calcium, and magnesium remain integrated within the solid-phase, while the majority of potassium and sodium reside in the liquid-phase. The fate of phosphorus is dependent on reaction times and temperatures, with solid-phase integration increasing with higher reaction temperature and longer time. A series of leaching experiments to determine potential solid-phase nutrient availability were also conducted and indicate that, at least in the short term, nitrogen release from the solids is small, while almost all of the phosphorus present in the solids produced from carbonizing at 225 and 250°C is released. At a reaction temperature of 275°C, smaller fractions of the solid-phase total phosphorus are released as reaction times increase, likely due to increased solids incorporation. Using these data, it is estimated that up to 0.96% and 2.30% of nitrogen and phosphorus-based fertilizers, respectively, in the US can be replaced by the nutrients integrated within hydrochar and liquid-phases generated from the carbonization of currently landfilled food wastes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of proximal vagotomy and Roux-en-Y diversion on gastric emptying kinetics in asymptomatic patients.

PubMed

Urbain, J L; Penninckx, F; Siegel, J A; Vandenborre, P; Van Cutsem, E; Vandenmaegdenbergh, V; De Roo, M

1990-10-01

The role of the distal stomach in gastric emptying was studied. Ten patients with proximal gastric vagotomy (PV) and 10 age-matched patients with Roux-en-Y gastro-jejunostomy (R-Y) were compared with 10 healthy controls. Gastric emptying of solids and liquids was determined by the use of Tc-99m SC scrambled eggs and In-111 DTPA. In PV, gastric emptying of both solids and liquids was delayed; the prolongation with solids was mainly accounted for by an abnormal lag phase. In R-Y patients, no lag phase was observed, and the solid emptying curve pattern was characterized by early rapid emptying followed by very slow emptying. Both the solid and liquid phases were prolonged. The lag phase is affected by proximal vagotomy and is mainly determined by the distal stomach, which appears to be essential for normal emptying.

INTERIOR VIEW, LOOKING WEST, WITH CRANE OPERATOR, TED SEALS, POURING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, LOOKING WEST, WITH CRANE OPERATOR, TED SEALS, POURING MOLTEN METAL INTO A 1,300 TON ELECTRIC HOLDING FURNACE OR MIXER. AN ELECTRONIC SCALE RECORDED THAT 50.5 TONS OF METAL WERE POURED INTO THE FURNACE DURING THIS POUR. - American Cast Iron Pipe Company, Mixer Building, 1501 Thirty-first Avenue North, Birmingham, Jefferson County, AL

Phase Behavior of Binary Mixture of Heptaethylene Glycol Decyl Ether and Water: Formation of Phase Compound in Solid Phase

PubMed

Nibu; Suemori; Inoue

1997-07-01

Differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FT-IR) were used to construct and characterize the phase diagram for a binary mixture of heptaethylene glycol decyl ether (C10 E7 ) and water in the temperature range from -60 to 80°C. Plots of the endothermic peak temperatures obtained by DSC measurements against compositions provided eutectic solid-liquid phase boundaries with a eutectic composition of 34 wt% of H2 O. On the other hand, heat of fusion per unit weight of the mixture changed discretely at the composition corresponding to the "eutectic" composition. Furthermore, the IR spectra obtained for the mixture in the solid phase were well reproduced as a superposition of those for the mixture of 34 wt% H2 O and pure components but were not reproduced by superimposing the spectra obtained for the solid surfactant and ice. These observations indicate that a solid phase compound is formed between C10 E7 and water with a stoichiometry of 1:14 and that the compound and pure components exist as separate phases, rather than the phases separating into surfactant and ice, which would be expected if the C10 E7 /water mixture formed a true eutectic mixture system. It is estimated from the composition corresponding to the phase compounds that two molecules of water per oxyethylene unit are bound to hydrophilic polyoxyethylene chain of C10 E7 to form a hydrated compound.

Quantification of VX Nerve Agent in Various Food Matrices by Solid-Phase Extraction Ultra-Performance Liquid ChromatographyTime-of-Flight Mass Spectrometry

DTIC Science & Technology

2016-04-01

QUANTIFICATION OF VX NERVE AGENT IN VARIOUS FOOD MATRICES BY SOLID-PHASE EXTRACTION ULTRA-PERFORMANCE...TITLE AND SUBTITLE Quantification of VX Nerve Agent in Various Food Matrices by Solid-Phase Extraction Ultra-Performance Liquid Chromatography... food matrices. The mixed-mode cation exchange (MCX) sorbent and Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) methods were used for

Fractography, fluidity, and tensile properties of aluminum/hematite particulate composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, S.C.; Girish, B.M.; Kamath, R.

1999-06-01

This paper examines the effect of hematite (iron oxide) particles on the fluidity of the molten composite as well as the tensile properties and fracture behavior of the solidified as-cast aluminum composites. The percentage of hematite in the composite was varied from 1 to 7% in steps of 2% by weight. The vortex method was employed to prepare the composites. It followed from the results obtained that the ultimate tensile strength and Young`s modulus of the composite increased while the liquid fluidity and solid ductility decreased with the increase in hematite content in the composite specimens. The fluidity of themore » liquid was greater in a metal mold than in a sand mold, and it decreased with an increase in reinforcing particle size and increased with pouring temperature. The presence of the reinforcing particles altered the fracture behavior of the solid composites considerably. Final fracture of the composite occurred due to the propagation of cracks through the matrix between the reinforcing particles.« less

Analytical methodologies based on LC-MS/MS for monitoring selected emerging compounds in liquid and solid phases of the sewage sludge.

PubMed

Boix, C; Ibáñez, M; Fabregat-Safont, D; Morales, E; Pastor, L; Sancho, J V; Sánchez-Ramírez, J E; Hernández, F

2016-01-01

In this work, two analytical methodologies based on liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) were developed for quantification of emerging pollutants identified in sewage sludge after a previous wide-scope screening. The target list included 13 emerging contaminants (EC): thiabendazole, acesulfame, fenofibric acid, valsartan, irbesartan, salicylic acid, diclofenac, carbamazepine, 4-aminoantipyrine (4-AA), 4-acetyl aminoantipyrine (4-AAA), 4-formyl aminoantipyrine (4-FAA), venlafaxine and benzoylecgonine. The aqueous and solid phases of the sewage sludge were analyzed making use of Solid-Phase Extraction (SPE) and UltraSonic Extraction (USE) for sample treatment, respectively. The methods were validated at three concentration levels: 0.2, 2 and 20 μg L(-1) for the aqueous phase, and 50, 500 and 2000 μg kg(-1) for the solid phase of the sludge. In general, the method was satisfactorily validated, showing good recoveries (70-120%) and precision (RSD < 20%). Regarding the limit of quantification (LOQ), it was below 0.1 μg L(-1) in the aqueous phase and below 50 μg kg(-1) in the solid phase for the majority of the analytes. The method applicability was tested by analysis of samples from a wider study on degradation of emerging pollutants in sewage sludge under anaerobic digestion. The key benefits of these methodologies are: • SPE and USE are appropriate sample procedures to extract selected emerging contaminants from the aqueous phase of the sewage sludge and the solid residue. • LC-MS/MS is highly suitable for determining emerging contaminants in both sludge phases. • Up to our knowledge, the main metabolites of dipyrone had not been studied before in sewage sludge.

Using reweighting and free energy surface interpolation to predict solid-solid phase diagrams

NASA Astrophysics Data System (ADS)

Schieber, Natalie P.; Dybeck, Eric C.; Shirts, Michael R.

2018-04-01

Many physical properties of small organic molecules are dependent on the current crystal packing, or polymorph, of the material, including bioavailability of pharmaceuticals, optical properties of dyes, and charge transport properties of semiconductors. Predicting the most stable crystalline form at a given temperature and pressure requires determining the crystalline form with the lowest relative Gibbs free energy. Effective computational prediction of the most stable polymorph could save significant time and effort in the design of novel molecular crystalline solids or predict their behavior under new conditions. In this study, we introduce a new approach using multistate reweighting to address the problem of determining solid-solid phase diagrams and apply this approach to the phase diagram of solid benzene. For this approach, we perform sampling at a selection of temperature and pressure states in the region of interest. We use multistate reweighting methods to determine the reduced free energy differences between T and P states within a given polymorph and validate this phase diagram using several measures. The relative stability of the polymorphs at the sampled states can be successively interpolated from these points to create the phase diagram by combining these reduced free energy differences with a reference Gibbs free energy difference between polymorphs. The method also allows for straightforward estimation of uncertainties in the phase boundary. We also find that when properly implemented, multistate reweighting for phase diagram determination scales better with the size of the system than previously estimated.

Quantitative tomographic measurements of opaque multiphase flows

DOE Office of Scientific and Technical Information (OSTI.GOV)

GEORGE,DARIN L.; TORCZYNSKI,JOHN R.; SHOLLENBERGER,KIM ANN

2000-03-01

An electrical-impedance tomography (EIT) system has been developed for quantitative measurements of radial phase distribution profiles in two-phase and three-phase vertical column flows. The EIT system is described along with the computer algorithm used for reconstructing phase volume fraction profiles. EIT measurements were validated by comparison with a gamma-densitometry tomography (GDT) system. The EIT system was used to accurately measure average solid volume fractions up to 0.05 in solid-liquid flows, and radial gas volume fraction profiles in gas-liquid flows with gas volume fractions up to 0.15. In both flows, average phase volume fractions and radial volume fraction profiles from GDTmore » and EIT were in good agreement. A minor modification to the formula used to relate conductivity data to phase volume fractions was found to improve agreement between the methods. GDT and EIT were then applied together to simultaneously measure the solid, liquid, and gas radial distributions within several vertical three-phase flows. For average solid volume fractions up to 0.30, the gas distribution for each gas flow rate was approximately independent of the amount of solids in the column. Measurements made with this EIT system demonstrate that EIT may be used successfully for noninvasive, quantitative measurements of dispersed multiphase flows.« less

Préface

NASA Astrophysics Data System (ADS)

Moncorgé, R.

2006-12-01

Cette nouvelle édition du Colloque UVX avait pour objectifs de : - réunir les chercheurs et les industriels intéressés par les applications et les développements les plus récents obtenus sur les sources UV, VUV et X, cohérentes ou incohérentes, et les optiques et matériaux associés ; - dresser un bilan des sources de photons à haute énergie et de leurs applications courantes et futures ; - susciter de nouvelles collaborations ; - ouvrir de nouveaux champs disciplinaires. Elle a été organisée par le laboratoire CIRIL au VVF de Colleville-sur-Mer, dans le département du Calvados, du 6 au 9 juin 2006, la journée du 5 juin ayant été consacrée à une réunion de travail du GDR CNRS SAXO, ce GDR regroupant une majorité de scientifiques concernés par le Colloque UVX. La manifestation a réuni ainsi une centaine de participants dont une dizaine d'exposants industriels. Parmi ces participants, trente étaient invités à donner une conférence orale. Une sélection a été faite également parmi les meilleures communications soumises par affiches pour qu'elles soient présentées oralement. Une trentaine de ces communications ont été préparées sous la forme d'articles de 6 à 12 pages et font l'objet de cet ouvrage. De nombreux travaux récents ont été exposés tant au niveau des sources que des techniques de caractérisation et des applications, ceci dans des domaines très divers allant de la physique des lasers et de la mise en forme spatiale et temporelle des faisceaux au domaine de l'imagerie médicale et biologiques en passant par les techniques de fabrication des cristaux, fibres et films minces organiques et inorganiques. Plusieurs résultats marquants en sont ressortis. Dans le domaine des sources, la mise en forme spatiale du faisceau laser utilisé pour la production d'harmoniques d'ordre élevé dans les gaz, ceci à l'aide de lames de phase peu onéreuses et simples d'utilisation, semble être une bonne solution pour accroître les efficacités de conversion et pour produire des impulsions UVX de quelques dizaines de microjoules. Parallèlement, des progrès notables ont été effectués dans la génération d'impulsions sub-100 as isolées accordables et de large bande spectrale en utilisant des impulsions de pompe ultracourtes bien contrôlée en phase. Il apparaît que la gamme spectrale accessible peut être encore largement étendue en jouant sur la longueur d'onde excitatrice et sur le milieu générateur pour pouvoir atteindre des impulsions de moins de 10 as. Des premiers résultats ont été aussi exposés concernant l'obtention d'un laser X à 18,9 nm pompé en incidence rasante (technique GRIP) à partir d'une cible de molybdène nickelloide et d'un laser Ti:Sa produisant des impulsions de plus de 2 microjoules. L'intérêt des milieux gazeux à excimères a été également de nouveau démontré pour l'amplification d'impulsions ultracourtes intenses TW dans le proche UV avec un contraste élevé (>1011). Bien qu'encore marginale, il faut enfin signaler l'arrivée des fibres optiques microstructurées avec la génération de supercontinuum de longueurs d'onde (spectre blanc) jusque dans le proche UV. Du côté des processus fondamentaux et des applications, sont particulièrement ressortis la caractérisation de plasmas denses utilisant des harmoniques élevées à l'aide d'une expérience interférométrique originale, la caractérisation de plasmas de taille nanométrique émetteurs de rayonnement X produits par interaction d'impulsions laser ultracourtes avec des agrégats de gaz rares ainsi que le dépôt de couches minces de biomolécules à l'aide de la technique MAPLE, technique susceptible d'améliorer la conservation des molécules, en particulier des protéines. Enfin, dans le domaine de la métrologie et de l'imagerie, l'importance des lames de phase dans la mise en forme spatiale des faisceaux, en particulier pour le projet Mega-Joule, a été de nouveau souligné, des progrès significatifs (réflectivité, bande passante, stabilité temporelle et thermique) ont été obtenus dans le domaine des revêtements interférentiels multicouches pour laser EUV autour de 40 nm, et des améliorations significatives, en particulier au niveau des détecteurs, ont été signalées dans le domaine de l'imagerie X du petit animal, la conception de sources dédiées à microfoyers délivrant des rayons X de basses énergies très rapides pour éviter le flou inhérent aux mouvements de l'animal restant encore nécessaire. Le Colloque a permis des échanges très fructueux entre laséristes et utilisateurs et entre scientifiques et industriels commercialisant sources, systèmes et détecteurs. Il a permis également de donner la parole à des intervenants très jeunes et souvent très brillants (doctorants et jeunes chercheurs) qui seront sans aucun doute les futurs responsables de nos laboratoires, centres de recherche et entreprises. Les progrès constatés résultant de travaux portant souvent sur les deux années écoulées (puisque c'est la fréquence choisie pour ce Colloque) et les résultats obtenus comme les perspectives annoncées montrant de nouveau toute la pertinence de cette manifestation, celle-ci sera reconduite en 2008.

Biofuel production utilizing a dual-phase cultivation system with filamentous cyanobacteria.

PubMed

Aoki, Jinichi; Kawamata, Toru; Kodaka, Asuka; Minakawa, Masayuki; Imamura, Nobukazu; Tsuzuki, Mikio; Asayama, Munehiko

2018-04-17

Biomass yields and biofuel production were examined in a dual (solid and liquid)-phase cultivation system (DuPHA) with the unique filamentous cyanobacteria, Pseudanabaena sp. ABRG 5-3 and Limnothrix sp. SK1-2-1. Continuous circular cultivation was driven under the indoor closed (IC) or indoor opened (IO) conditions and provided biomass yields of approximately 8 to 27 g dry cell weight (DCW) floor m -2 d -1 . Alkanes of heptadecane (C 17 H 36 ) or pentadecane (C 15 H 32 ) as liquid biofuels were also recovered from the lower liquid-phase, in which cyanobacteria were dropped from the upper solid-phase and continuously cultivated with a small amount of medium. After the main cultivation in DuPHA, the upper solid-phase of a cotton cloth on which cyanobacteria grew was dried and directly subjected to a combustion test. This resulted in the thermal power (kJ s -1 ) of the cloth with microalgae increasing approximately 20 to 50% higher than that of the cloth only, suggesting a possibility of using the solid phase with microalgae as solid biofuel. Copyright © 2018. Published by Elsevier B.V.

Biological nitrate removal from water and wastewater by solid-phase denitrification process.

PubMed

Wang, Jianlong; Chu, Libing

2016-11-01

Nitrate pollution in receiving waters has become a serious issue worldwide. Solid-phase denitrification process is an emerging technology, which has received increasing attention in recent years. It uses biodegradable polymers as both the carbon source and biofilm carrier for denitrifying microorganisms. A vast array of natural and synthetic biopolymers, including woodchips, sawdust, straw, cotton, maize cobs, seaweed, bark, polyhydroxyalkanoate (PHA), polycaprolactone (PCL), polybutylene succinate (PBS) and polylactic acid (PLA), have been widely used for denitrification due to their good performance, low cost and large available quantities. This paper presents an overview on the application of solid-phase denitrification in nitrate removal from drinking water, groundwater, aquaculture wastewater, the secondary effluent and wastewater with low C/N ratio. The types of solid carbon source, the influencing factors, the microbial community of biofilm attached on the biodegradable carriers, the potential adverse effect, and the cost of denitrification process are introduced and evaluated. Woodchips and polycaprolactone are the popular and competitive natural plant-like and synthetic biodegradable polymers used for denitrification, respectively. Most of the denitrifiers reported in solid-phase denitrification affiliated to the family Comamonadaceae in the class Betaproteobacteria. The members of genera Diaphorobacter, Acidovorax and Simplicispira were mostly reported. In future study, more attention should be paid to the simultaneous removal of nitrate and toxic organic contaminants such as pesticide and PPCPs by solid-phase denitrification, to the elucidation of the metabolic and regulatory relationship between decomposition of solid carbon source and denitrification, and to the post-treatment of the municipal secondary effluent. Solid-phase denitrification process is a promising technology for the removal of nitrate from water and wastewater. Copyright © 2016 Elsevier Inc. All rights reserved.

Solid-State NMR Investigation of Drug-Excipient Interactions and Phase Behavior in Indomethacin-Eudragit E Amorphous Solid Dispersions.

PubMed

Lubach, Joseph W; Hau, Jonathan

2018-02-20

To investigate the nature of drug-excipient interactions between indomethacin (IMC) and methacrylate copolymer Eudragit® E (EE) in the amorphous state, and evaluate the effects on formulation and stability of these amorphous systems. Amorphous solid dispersions containing IMC and EE were spray dried with drug loadings from 20% to 90%. PXRD was used to confirm the amorphous nature of the dispersions, and DSC was used to measure glass transition temperatures (T g ). 13 C and 15 N solid-state NMR was utilized to investigate changes in local structure and protonation state, while 1 H T 1 and T 1ρ relaxation measurements were used to probe miscibility and phase behavior of the dispersions. T g values for IMC-EE solid dispersions showed significant positive deviations from predicted values in the drug loading range of 40-90%, indicating a relatively strong drug-excipient interaction. 15 N solid-state NMR exhibited a change in protonation state of the EE basic amine, with two distinct populations for the EE amine at -360.7 ppm (unprotonated) and -344.4 ppm (protonated). Additionally, 1 H relaxation measurements showed phase separation at high drug load, indicating an amorphous ionic complex and free IMC-rich phase. PXRD data showed all ASDs up to 90% drug load remained physically stable after 2 years. 15 N solid-state NMR experiments show a change in protonation state of EE, indicating that an ionic complex indeed forms between IMC and EE in amorphous solid dispersions. Phase behavior was determined to exhibit nanoscale phase separation at high drug load between the amorphous ionic complex and excess free IMC.

Further insight into the mechanism of heavy metals partitioning in stormwater runoff.

PubMed

Djukić, Aleksandar; Lekić, Branislava; Rajaković-Ognjanović, Vladana; Veljović, Djordje; Vulić, Tatjana; Djolić, Maja; Naunovic, Zorana; Despotović, Jovan; Prodanović, Dušan

2016-03-01

Various particles and materials, including pollutants, deposited on urban surfaces are washed off by stormwater runoff during rain events. The interactions between the solid and dissolved compounds in stormwater runoff are phenomena of importance for the selection and improvement of optimal stormwater management practices aimed at minimizing pollutant input to receiving waters. The objective of this research was to further investigate the mechanisms responsible for the partitioning of heavy metals (HM) between the solid and liquid phases in urban stormwater runoff. The research involved the collection of samples from urban asphalt surfaces, chemical characterization of the bulk liquid samples, solids separation, particle size distribution fractionation and chemical and physico-chemical characterization of the solid phase particles. The results revealed that a negligible fraction of HM was present in the liquid phase (less than 3% by weight), while there was a strong correlation between the total content of heavy metals and total suspended solids. Examinations of surface morphology and mineralogy revealed that the solid phase particles consist predominantly of natural macroporous materials: alpha quartz (80%), magnetite (11.4%) and silicon diphosphate (8.9%). These materials have a low surface area and do not have significant adsorptive capacity. These materials have a low surface area and do not have significant adsorptive capacity. The presence of HM on the surface of solid particles was not confirmed by scanning electron microscopy and energy dispersive X-ray microanalyses. These findings, along with the results of the liquid phase sample characterization, indicate that the partitioning of HM between the liquid and solid phases in the analyzed samples may be attributed to precipitation processes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Method for removing solid particulate material from within liquid fuel injector assemblies

DOEpatents

Simandl, R.F.; Brown, J.D.; Andriulli, J.B.; Strain, P.D.

1998-09-08

A method is described for removing residual solid particulate material from the interior of liquid fuel injectors and other fluid flow control mechanisms having or being operatively associated with a flow-regulating fixed or variable orifice. The method comprises the sequential and alternate introduction of columns of a non-compressible liquid phase and columns of a compressed gas phase into the body of a fuel injector whereby the expansion of each column of the gas phase across the orifice accelerates the liquid phase in each trailing column of the liquid phase and thereby generates turbulence in each liquid phase for lifting and entraining the solid particulates for the subsequent removal thereof from the body of the fuel injector. 1 fig.

Method for removing solid particulate material from within liquid fuel injector assemblies

DOEpatents

Simandl, Ronald F.; Brown, John D.; Andriulli, John B.; Strain, Paul D.

1998-01-01

A method for removing residual solid particulate material from the interior of liquid fuel injectors and other fluid flow control mechanisms having or being operatively associated with a flow-regulating fixed or variable orifice. The method comprises the sequential and alternate introduction of columns of a non-compressible liquid phase and columns of a compressed gas phase into the body of a fuel injector whereby the expansion of each column of the gas phase across the orifice accelerates the liquid phase in each trailing column of the liquid phase and thereby generates turbulence in each liquid phase for lifting and entraining the solid particulates for the subsequent removal thereof from the body of the fuel injector.

Study on ABO and RhD blood grouping: Comparison between conventional tile method and a new solid phase method (InTec Blood Grouping Test Kit).

PubMed

Yousuf, R; Abdul Ghani, S A; Abdul Khalid, N; Leong, C F

2018-04-01

'InTec Blood Grouping Test kit' using solid-phase technology is a new method which may be used at outdoor blood donation site or at bed side as an alternative to the conventional tile method in view of its stability at room temperature and fulfilled the criteria as point of care test. This study aimed to compare the efficiency of this solid phase method (InTec Blood Grouping Test Kit) with the conventional tile method in determining the ABO and RhD blood group of healthy donors. A total of 760 voluntary donors who attended the Blood Bank, Penang Hospital or offsite blood donation campaigns from April to May 2014 were recruited. The ABO and RhD blood groups were determined by the conventional tile method and the solid phase method, in which the tube method was used as the gold standard. For ABO blood grouping, the tile method has shown 100% concordance results with the gold standard tube method, whereas the solid-phase method only showed concordance result for 754/760 samples (99.2%). Therefore, for ABO grouping, tile method has 100% sensitivity and specificity while the solid phase method has slightly lower sensitivity of 97.7% but both with good specificity of 100%. For RhD grouping, both the tile and solid phase methods have grouped one RhD positive specimen as negative each, thus giving the sensitivity and specificity of 99.9% and 100% for both methods respectively. The 'InTec Blood Grouping Test Kit' is suitable for offsite usage because of its simplicity and user friendliness. However, further improvement in adding the internal quality control may increase the test sensitivity and validity of the test results.

Molecularly imprinted solid-phase extraction sorbent for the clean-up of chlorinated phenoxyacids from aqueous samples.

PubMed

Baggiani, C; Giovannoli, C; Anfossi, L; Tozzi, C

2001-12-14

A molecularly imprinted polymer (MIP) was synthesized using the herbicide 2,4,5-trichlorophenoxyacetic acid as a template, 4-vinylpyridine as an interacting monomer, ethylendimethacrylate as a cross-linker and a methanol-water mixture as a porogen. The binding properties and the selectivity of the polymer towards the template were investigated by frontal and zonal liquid chromatography. The polymer was used as a solid-phase extraction material for the clean-up of the template molecule and some related herbicides (2,4-dichlorophenoxyacetic acid, fenoprop, dichlorprop) from river water samples at a concentration level of ng/ml with quantitative recoveries comparable with those obtained with a traditional C18 reversed-phase column when analyzed by capillary electrophoresis. The results obtained show that the MIP-based approach to the solid-phase extraction is comparable with the more traditional solid-phase extraction with C18 reversed-phase columns in terms of recovery, but it is superior in terms of sample clean-up.

Encapsulated Solid-Liquid Phase Change Nanoparticles as Thermal Barcodes for Highly Sensitive Detections of Multiple Lung Cancer Biomarkers

DTIC Science & Technology

2012-10-01

5e. TASK NUMBER LC90061 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT...transduction mechanism based on solid- liquid phase change nanoparticles works for the detection of multiple proteins. A series of metal and alloy...early stage. With the support from DOD-LCRP, we have proved the new signal transduction mechanism based on solid-liquid phase change nanoparticles works

A review on solid phase extraction of actinides and lanthanides with amide based extractants.

PubMed

Ansari, Seraj A; Mohapatra, Prasanta K

2017-05-26

Solid phase extraction is gaining attention from separation scientists due to its high chromatographic utility. Though both grafted and impregnated forms of solid phase extraction resins are popular, the later is easy to make by impregnating a given organic extractant on to an inert solid support. Solid phase extraction on an impregnated support, also known as extraction chromatography, combines the advantages of liquid-liquid extraction and the ion exchange chromatography methods. On the flip side, the impregnated extraction chromatographic resins are less stable against leaching out of the organic extractant from the pores of the support material. Grafted resins, on the other hand, have a higher stability, which allows their prolong use. The goal of this article is a brief literature review on reported actinide and lanthanide separation methods based on solid phase extractants of both the types, i.e., (i) ligand impregnation on the solid support or (ii) ligand functionalized polymers (chemically bonded resins). Though the literature survey reveals an enormous volume of studies on the extraction chromatographic separation of actinides and lanthanides using several extractants, the focus of the present article is limited to the work carried out with amide based ligands, viz. monoamides, diamides and diglycolamides. The emphasis will be on reported applied experimental results rather than on data pertaining fundamental metal complexation. Copyright © 2017 Elsevier B.V. All rights reserved.

Quantitative ionspray liquid chromatographic/tandem mass spectrometric determination of reserpine in equine plasma.

PubMed

Anderson, M A; Wachs, T; Henion, J D

1997-02-01

A method based on ionspray liquid chromatography/tandem mass spectrometry (LC/MS/MS) was developed for the determination of reserpine in equine plasma. A comparison was made of the isolation of reserpine from plasma by liquid-liquid extraction and by solid-phase extraction. A structural analog, rescinnamine, was used as the internal standard. The reconstituted extracts were analyzed by ionspray LC/MS/MS in the selected reaction monitoring (SRM) mode. The calibration graph for reserpine extracted from equine plasma obtained using liquid-liquid extraction was linear from 10 to 5000 pg ml-1 and that using solid-phase extraction from 100 to 5000 pg ml-1. The lower level of quantitation (LLQ) using liquid-liquid and solid-phase extraction was 50 and 200 pg ml-1, respectively. The lower level of detection for reserpine by LC/MS/MS was 10 pg ml-1. The intra-assay accuracy did not exceed 13% for liquid-liquid and 12% for solid-phase extraction. The recoveries for the LLQ were 68% for liquid-liquid and 58% for solid-phase extraction.

Recent Approaches Toward Solid Phase Synthesis of β-Lactams

NASA Astrophysics Data System (ADS)

Mandal, Bablee; Ghosh, Pranab; Basu, Basudeb

Since the discovery of penicillin in 1929, β-lactam antibiotics have been recognized as potentially chemotherapeutic drugs of incomparable effectiveness, conjugating a broad spectrum of activity with very low toxicity. The primary motif azetidin-2-one ring (β-lactam) has been considered as specific pharmacophores and scaffolds. With the advent of combinatorial chemistry and automated parallel synthesis coupled with ample interests from the pharmaceutical industries, recent trends have been driven mostly by adopting solid phase techniques and polymer-supported synthesis of β-lactams. The present survey will present an overview of the developments on the polymer-supported and solid phase techniques for the preparation of β-lactam ring or β-lactam containing antibiotics published over the last decade. Both unsubstituted and substitutions with different functional groups at various positions of β-lactams have been synthesized using solid phase technology. However, Wang resin and application of Staudinger [2+2] cycloaddition reaction have remained hitherto the major choice. It may be expected that other solid phase approaches involving different resins would be developed in the coming years.

Modification of Alumina and Spinel Inclusions by Calcium in Liquid Steel

NASA Astrophysics Data System (ADS)

Verma, Neerav

2011-12-01

Steel Cleanliness plays a crucial role in determining steel properties such as toughness, ductility, formability, corrosion resistance and surface quality. The production of clean steel often involves the elimination or chemical and morphological modification of oxide and sulfide inclusions. Along with deteriorating the steel properties, solid inclusions can affect steel castability through nozzle clogging. Nozzle clogging occurs when solid inclusions accumulate in the caster pouring system such as the ladle shroud or submerged entry nozzle (SEN). Thus, it is important to understand how to achieve desired inclusion characteristics (shape, size and chemistry) through the steelmaking process. Among the various practices adopted in industries to counteract the effect of solid inclusions, modification of solid inclusions to liquid or partially liquid state through calcium treatment is one of the methods. Calcium can be used because it has a strong ability to form oxides and sulfides. In Al-killed steels, the most common inclusions are alumina (Al2O3) inclusions, which are solid at steelmaking temperatures. On calcium treatment, solid alumina inclusions are converted to calcium aluminates, which have liquidus temperatures lower than steelmaking temperature (1600°C) [14]. It has been found that alumina inclusions may contain some MgO and such inclusions are termed alumina magnesia spinels (Al2O3.xMgO) [18]. These spinels are more stable than alumina and it has been suggested that they might be more difficult to modify [18]. But, some authors have proposed that MgO can actually help in the liquefaction of inclusions, and have demonstrated successful modification of spinels by Ca treatment [20, 21]. In the present research, the mechanism of transformation of alumina and spinel inclusions upon calcium treatment was studied by characterizing transient evolution of inclusions. A vacuum induction was used for melting, making additions (Al, Al-Mg and CaSi2) and sampling. The samples were characterized for inclusion shape, size and chemistry through scanning electron microscopy (SEM). Automated inclusion analysis tools (like ASCAT [59, 91, 92], INCA-GSR [126]; Please refer section 6.4., page number 68) were employed to generate statistical information of the inclusions. Thermodynamic database software FACTSAGE [62] was used to determine thermochemistry of reactions, ternary phase diagrams (Ca-Al-S and Ca-Al-Mg systems). The compositions of the inclusions were tracked before and after calcium treatment to determine the effectiveness of calcium treatment. Extraction of inclusions through dissolution of iron in bromine-methanol solution was employed to reveal 3-D geometry of inclusions and analyze inclusions through EDS (Energy-dispersive X-ray spectroscopy) without any matrix effects. Various industrial samples were also analyzed to confirm the feasibility of various reaction mechanisms deduced through experiments. Successful modification of alumina and spinel inclusions by calcium was demonstrated [85, 86]. It was observed that these modification mechanisms proceed through transient phase (CaO, CaS) formation. In the case of spinels, preferential reduction of MgO part was also observed during calcium modification of spinels. The magnesium after MgO reduction by calcium can enter back into the melt or leave the melt in vapor form. The inclusion area fraction decreased after calcium treatment, but the inclusion concentration (number of inclusions per cm2) increased because inclusions shifted to a smaller size distribution after calcium treatment. Severe matrix effects during EDS analysis of inclusions were observed, due to which inclusion composition analyses can be significantly affected. *Please refer to dissertation for footnotes.

Nonaqueous slip casting of high temperature ceramic superconductors using an investment casting technique

NASA Technical Reports Server (NTRS)

Hooker, Matthew W. (Inventor); Taylor, Theodore D. (Inventor); Wise, Stephanie A. (Inventor); Buckley, John D. (Inventor); Vasquez, Peter (Inventor); Buck, Gregory M. (Inventor); Hicks, Lana P. (Inventor)

1993-01-01

A process for slip casting ceramic articles that does not employ parting agents and affords the casting of complete, detailed, precision articles that do not possess parting lines is presented. This process is especially useful for high temperature superconductors and water-sensitive ceramics. A wax pattern for a shell mold is provided, and an aqueous mixture of a calcium sulfate-bonded investment material is applied as a coating to the wax pattern. The coated wax pattern is then dried, followed by curing to vaporize the wax pattern and leave a shell mold of the calcium sulfate-bonded investment material. The shell mold is cooled to room temperature, and a ceramic slip, created by dispersing a ceramic powder in an organic liquid, is poured therein. After a ceramic shell of desired thickness or a solid article has set up in the shell mold, excess ceramic slip is poured out. The shell mold is misted with water and peeled away from the ceramic article, after which the ceramic is fired to provide a complete, detailed, precision, high temperature superconductive ceramic article without parting lines. The casting technique may take place in the presence of a magnetic field to orient the ceramic powders during the casting process.

A mechanistic model for the prediction of in-use moisture uptake by packaged dosage forms.

PubMed

Remmelgas, Johan; Simonutti, Anne-Laure; Ronkvist, Asa; Gradinarsky, Lubomir; Löfgren, Anders

2013-01-30

A mechanistic model for the prediction of in-use moisture uptake of solid dosage forms in bottles is developed. The model considers moisture transport into the bottle and moisture uptake by the dosage form both when the bottle is closed and when it is open. Experiments are carried out by placing tablets and desiccant canisters in bottles and monitoring their moisture content. Each bottle is opened once a day to remove one tablet or desiccant canister. Opening the bottle to remove a tablet or canister also causes some exchange of air between the bottle headspace and the environment. In order to ascertain how this air exchange might depend on the customer, tablets and desiccant canisters are removed from the bottles by either carefully removing only one or by pouring all of the tablets or desiccant canisters out of the bottle, removing one, and pouring the remaining ones back into the bottle. The predictions of the model are found to be in good agreement with experimental data for moisture sorption by desiccant canisters. Moreover, it is found experimentally that the manner in which the tablets or desiccant canisters were removed does not appreciably affect their moisture content. Copyright © 2012 Elsevier B.V. All rights reserved.

Méthode de traitement des intérferogrammes à deux ondes pour accroître leur sensibilité.

PubMed

Roblin, G; Prévost, M

1980-08-01

Two-beam interference fringes are not always able to give sufficient information to determine the topography of very weakly deformed wave surfaces. The process described allows us to intercalate several intermediate levels, which vary linearly in terms of the phase, between the brightness extrema of a fringe. The interference pattern is submitted to an optoelectronics treatment where the photoelectric signal is compared with an adjustable electric reference signal.

Upper critical field measurements in high-Tc superconducting oxides

NASA Astrophysics Data System (ADS)

Ousset, J. C.; Bobo, J. F.; Ulmet, J. P.; Rakoto, H.; Cheggour, N.

We present upper critical field measurements on the superconducting oxides RE Ba2Cu3O7-δ (RE = Y, Gd) performed in a pulsed magnetic field up to 43 T. Values for Hc2 as high as 52 T and 77 T for Y and Gd respectively, are expected at 77 K. However, in order to observe no resistive behaviour up to 43 T the temperature must be decreased down to 50 K. In the case of oxygen deficient systems the magnetoresistance reveals two superconducting phases wich could be related to two different orders of oxygen vacancies. Nous présentons des mesures de champ critique Hc2 sur les supraconducteurs TR Ba 2Cu3O7-δ (TR = Y, Gd) réalisées en champ magnétique pulsé jusqu'à 43 T. Elles permettent de prévoir des valeurs de H c2 de 52 T et 77 T respectivement pour Y et Gd à 77 K. Cependant, pour ne pas observer de comportement résistif jusqu'au champ maximum, il est nécessaire de refroidir l'échantillon jusqu'à 50 K. Dans le cas des systèmes déficients en oxygène (δ important) nous mettons en évidence l'existence de deux phases supraconductrices qui pourraient être dues à deux ordres différents des lacunes d'oxygène.

The Gaseous Phase as a Probe of the Astrophysical Solid Phase Chemistry

NASA Astrophysics Data System (ADS)

Abou Mrad, Ninette; Duvernay, Fabrice; Isnard, Robin; Chiavassa, Thierry; Danger, Grégoire

2017-09-01

In support of space missions and spectroscopic observations, laboratory experiments on ice analogs enable a better understanding of organic matter formation and evolution in astrophysical environments. Herein, we report the monitoring of the gaseous phase of processed astrophysical ice analogs to determine if the gaseous phase can elucidate the chemical mechanisms and dominant reaction pathways occurring in the solid ice subjected to vacuum ultra-violet (VUV) irradiation at low temperature and subsequently warmed. Simple (CH3OH), binary (H2O:CH3OH, CH3OH:NH3), and ternary ice analogs (H2O:CH3OH:NH3) were VUV-processed and warmed. The evolution of volatile organic compounds in the gaseous phase shows a direct link between their relative abundances in the gaseous phase, and the radical and thermal chemistries modifying the initial ice composition. The correlation between the gaseous and solid phases may play a crucial role in deciphering the organic composition of astrophysical objects. As an example, possible solid compositions of the comet Lovejoy are suggested using the abundances of organics in its comae.

Melting along the Hugoniot and solid phase transition for Sn via sound velocity measurements

NASA Astrophysics Data System (ADS)

Song, Ping; Cai, Ling-cang; Tao, Tian-jiong; Yuan, Shuai; Chen, Hong; Huang, Jin; Zhao, Xin-wen; Wang, Xue-jun

2016-11-01

It is very important to determine the phase boundaries for materials with complex crystalline phase structures to construct their corresponding multi-phase equation of state. By measuring the sound velocity of Sn with different porosities, different shock-induced melting pressures along the solid-liquid phase boundary could be obtained. The incipient shock-induced melting of porous Sn samples with two different porosities occurred at a pressure of about 49.1 GPa for a porosity of 1.01 and 45.6 GPa for a porosity of 1.02, based on measurements of the sound velocity. The incipient shock-induced melting pressure of solid Sn was revised to 58.1 GPa using supplemental measurements of the sound velocity. Trivially, pores in Sn decreased the shock-induced melting pressure. Based on the measured longitudinal sound velocity data, a refined solid phase transition and the Hugoniot temperature-pressure curve's trend are discussed. No bcc phase transition occurs along the Hugoniot for porous Sn; further investigation is required to understand the implications of this finding.

Melting of Simple Solids and the Elementary Excitations of the Communal Entropy

NASA Astrophysics Data System (ADS)

Bongiorno, Angelo

2010-03-01

The melting phase transition of simple solids is addressed through the use of atomistic computer simulations. Three transition metals (Ni, Au, and Pt) and a semiconductor (Si) are considered in this study. Iso-enthalpic molecular dynamics simulations are used to compute caloric curves across the solid-to-liquid phase transition of a periodic crystalline system, to construct the free energy function of the solid and liquid phases, and thus to derive the thermodynamical limit of the melting point, latent heat and entropy of fusion of the material. The computational strategy used in this study yields accurate estimates of melting parameters, it consents to determine the superheating and supercooling temperature limits, and it gives access to the atomistic mechanisms mediating the melting process. In particular, it is found that the melting phase transition in simple solids is driven by exchange steps involving a few atoms and preserving the crystalline structure. These self-diffusion phenomena correspond to the elementary excitations of the communal entropy and, as their rate depends on the local material cohesivity, they mediate both the homogeneous and non-homogeneous melting process in simple solids.

[Determination of lead in edible salt with solid-phase extraction and GFAAS].

PubMed

Zhao, Xin; Zhou, Shuang; Ma, Lan; Yang, Dajin

2013-01-01

Establishing a method for determination of lead in salt with solid-phase extraction and GFAAS. Salt sample was diluted to a certain volume directly with ammonium acetate, then the sample solution was filtered through the solid phase extraction column which has been pre-activated. Lead ions were retained, and the sodium chloride matrix was removed. After elution, the collected lead ions was determined by graphite furnace atomic absorption spectrometry in 257.4 nm. This method can be used effectively to wipe off the sodium chloride in matrix. The limit of detection was 0.7 microg/kg and the limit of quantification was 2 microg/kg. Solid phase extraction technique can be used effectively to reduce the interference in matrix and improves the accuracy and reproducibility of detection.

Self-healing liquid/solid state battery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burke, Paul J.; Chung, Brice H.V.; Phadke, Satyajit R.

A battery system that exchanges energy with an external device is provided. The battery system includes a positive electrode having a first metal or alloy, a negative electrode having a second metal or alloy, and an electrolyte including a salt of the second metal or alloy. The positive electrode, the negative electrode, and the electrolyte are in a liquid phase at an operating temperature during at least one portion of operation. The positive electrode is entirely in a liquid phase in one charged state and includes a solid phase in another charged state. The solid phase of the positive electrodemore » includes a solid intermetallic formed by the first and the second metals or alloys. Methods of storing electrical energy from an external circuit using such a battery system are also provided.« less

Studies in Three Phase Gas-Liquid Fluidised Systems

NASA Astrophysics Data System (ADS)

Awofisayo, Joyce Ololade

1992-01-01

Available from UMI in association with The British Library. The work is a logical continuation of research started at Aston some years ago when studies were conducted on fermentations in bubble columns. The present work highlights typical design and operating problems that could arise in such systems as waste water, chemical, biochemical and petroleum operations involving three-phase, gas-liquid -solid fluidisation; such systems are in increasing use. It is believed that this is one of few studies concerned with "true" three-phase, gas-liquid-solid fluidised systems, and that this work will contribute significantly to closing some of the gaps in knowledge in this area. The research work was experimentally based and involved studies of the hydrodynamic parameters, phase holdups (gas and solid), particle mixing and segregation, and phase flow dynamics (flow regime and circulation patterns). The studies have focused particularly on the solid behaviour and the influence of properties of solids present on the above parameters in three-phase, gas-liquid-solid fluidised systems containing single particle components and those containing binary and ternary mixtures of particles. All particles were near spherical in shape and two particle sizes and total concentration levels were used. Experiments were carried out in two- and three-dimensional bubble columns. Quantitative results are presented in graphical form and are supported by qualitative results from visual studies which are also shown as schematic diagrams and in photographic form. Gas and solid holdup results are compared for air-water containing single, binary and ternary component particle mixtures. It should be noted that the criteria for selection of the materials used are very important if true three-phase fluidisation is to be achieved: this is very evident when comparing the results with those in the literature. The fluid flow and circulation patterns observed were assessed for validation of the generally accepted patterns, and the author believes that the present work provides more accurate insight into the modelling of liquid circulation in bubble columns. The characteristic bubbly flow at low gas velocity in a two-phase system is suppressed in the three-phase system. The degree of mixing within the system is found to be dependent on flow regime, liquid circulation and the ratio of solid phase physical properties.

A method of solid-solid phase equilibrium calculation by molecular dynamics

NASA Astrophysics Data System (ADS)

Karavaev, A. V.; Dremov, V. V.

2016-12-01

A method for evaluation of solid-solid phase equilibrium curves in molecular dynamics simulation for a given model of interatomic interaction is proposed. The method allows to calculate entropies of crystal phases and provides an accuracy comparable with that of the thermodynamic integration method by Frenkel and Ladd while it is much simpler in realization and less intense computationally. The accuracy of the proposed method was demonstrated in MD calculations of entropies for EAM potential for iron and for MEAM potential for beryllium. The bcc-hcp equilibrium curves for iron calculated for the EAM potential by the thermodynamic integration method and by the proposed one agree quite well.

Investigation de l'anisotropie du gap supraconducteur dans les composes Ba(Fe(1-x)Co(x))2As2, Ba(1-x)K(x)Fe2As2, LiFeAs et Fe1-deltaTe(1-x)Se(x)

NASA Astrophysics Data System (ADS)

Reid, Jean-Philippe

ommaire La structure du gap supraconducteur et sa modulation sont intimement liees au potentiel d'interaction responsable de l'appariement des electrons d'un supraconducteur. Ainsi, l'etude de la structure du gap-SC et de sa modulation permettent de faire la lumiere sur la nature du mecanisme d'appariement des electrons. A cet egard, les resultats experimentaux des supraconducteurs a base de fer ne cadrent pas dans un seul ensemble, ce qui est en opposition au gap-SC universel des cuprates. Dans ce qui suit, nous presenterons une etude systematique du gap-SC pour plusieurs pnictides. En effet, en utilisant la conductivite thermique, une sonde directionnelle du gap-SC, nous avons ete en mesure de reveler la structure du gap-SC pour les composes suivants : Ba1-xKxFe 2As2, Ba(Fe1-xCo x)2As2, LiFeAs et Fe1-deltaTe 1-xSex. L'etude de ces quatre composes, de trois differentes familles structurales, a pu etablir un tableau partiel mais tres exhaustif de la structure du gap-SC de pnictides. En effet, tel qu'illustre dans cette these, ces quatre composes ne possedent aucun noeud dans leur structure du gap-SC a dopage optimal. Toutefois, a une concentration differente de celle optimale pour les composes K-Ba122 et Co-Ba122, des noeuds apparaissent sur la surface de Fermi, aux extremites 'du dome supraconducteur. Ceci suggere fortement que, pour ces composes, la presence de noeuds sur la surface de Fermi est nuisible a la phase supraconductrice. Mots-cles: Supraconducteurs a base de fer, Pnictides, Structure du gap supraconducteur, Conductivite thermique

Interdiffusion and Intrinsic Diffusion in the Mg-Al System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brennan, Sarah; Bermudez, Katrina; Sohn, Yong Ho

2012-01-01

Solid-to-solid diffusion couples were assembled and annealed to examine the diffusion between pure Mg (99.96%) and Al (99.999%). Diffusion anneals were carried out at 300 , 350 , and 400 C for 720, 360, and 240 hours, respectively. Optical and scanning electron microscopes were utilized to identify the formation of the intermetallic phases, -Al12Mg17 and -Al3Mg2 and absence of the -phase in the diffusion couples. Thicknesses of the -Al12Mg17 and -Al3Mg2 phases were measured and the parabolic growth constants were calculated to determine the activation energies for the growth, 165 and 86 KJ/mole, respectively. Concentration profiles were determined with electronmore » microprobe analysis using pure elemental standards. Composition-dependent interdiffusion coefficients in Mg-solid solution, -Al12Mg17 and - Al3Mg2 and Al-solid solutions were calculated based on the Boltzmann-Matano analysis. Average effective interdiffusion coefficients for each phase were also calculated, and the magnitude was the highest for the -Al3Mg2 phase, followed by -Al12Mg17, Al-solid solution and Mg-solid solution. Intrinsic diffusion coefficients based on Huemann s analysis (e.g., marker plane) were determined for the ~38 at.% Mg in the -Al3Mg2 phase. Activation energies and the pre-exponential factors for the inter- and intrinsic diffusion coefficients were calculated for the temperature range examined. The -Al3Mg2 phase was found to have the lowest activation energies for growth and interdiffusion among all four phases studied. At the marker location in the -Al3Mg2 phase, the intrinsic diffusion of Al was found to be faster than that of Mg. Extrapolations of the impurity diffusion coefficients in the terminal solid solutions were made and compared to the available self- and impurity diffusion data from literature. Thermodynamic factor, tracer diffusion coefficients and atomic mobilities at the marker plane composition were approximated using available literature values of Mg activity in the -Al3Mg2 phase.« less

Hydrodynamic Coating of a Fiber

NASA Astrophysics Data System (ADS)

Quéré, D.; de Ryck, A.

We discuss how a solid (especially a fiber) is coated when drawn out of a bath of liquid. 1. For slow withdrawals out of pure viscous liquids, the data are found to be fitted by the famous Landau law: then, the coating results from a balance between viscosity and capillarity. For quicker withdrawals, the thickness of the entrained film suddenly diverges, at a velocity on order 1 m/s. Inertia is shown to be responsible for this effect. At still higher velocities, the thickness decreases with the velocity because the solid can only entrain the viscous boundary layer. 2. For complex fluids, surface effects are found in the low velocity regime: out of a surfactant solution, films are thicker than predicted by Landau, by a factor of order 2. The thickening factor is shown to be fixed by the Marangoni flow due to the presence of surfactants; out of an emulsion, the film can be enriched with oil , which can be understood by a simple model of capture; out of a polymer solution, a strong swelling of the film is observed if normal stresses are present. Hence, the problem has two families of solution: (i) at low velocity, the thickness of the layer is fixed by a balance between viscous and surface forces and thus is sensitive to the presence of surfactants, or other heterogeneities; (ii) at high velocity, inertia must be considered and the film thickness is fixed by the bulk properties of the liquid (density and viscosity). In these regimes, it is not affected by the presence of surfactants in the bath. Nous décrivons le dépôt de liquide sur un solide (le plus souvent une fibre) qui advient quand on tire ce solide d'un bain. 1. Si le retrait se fait lentement hors d'un liquide pur et visqueux, les données expérimentales suivent la loi de Landau : le dépôt résulte d'un compromis entre forces visqueuses et forces capillaires. Pour des retraits plus rapides, on observe que l'épaisseur du dépôt diverge, pour une vitesse de l'ordre du mètre par seconde. Nous montrons comment l'inertie du fluide engendre un tel effet. Plus vite encore, l'épaisseur décroît lentement avec la vitesse, le solide ne parvenant à entraîner avec lui que la couche limite visqueuse qu'il a mis en mouvement. 2. Pour des liquides complexes, des effets de surface sont observés dans le régime basse vitesse : hors d'une solution de tensioactifs, les films sont plus épais que ce que prévoit la loi de Landau, d'un facteur 2 environ. Nous montrons que l'épaississement est déterminé par l'écoulement Marangoni dû à la présence des tensioactifs ; hors d'une émulsion, le film peut être enrichi en huile, ce que l'on peut interpréter à l'aide d'un modèle de capture ; hors d'une solution de polymère, on observe un fort gonflement du film dès que la solution est semi-diluée, à cause de l'effet des contraintes normales (effet Weissenberg). Le problème étudié a donc deux familles de solution : (i) à basse vitesse, le dépôt résulte d'un compromis entre viscosité et capillarité, si bien qu'il est sensible à la présence dans le bain d'hétérogénéités (tensioactifs, gouttes d'huile) ; (ii) à plus grande vitesse, l'inertie doit être prise en compte et l'épaisseur du film est alors liée aux propriétés de volume du liquide (densité et viscosité).

Investigation on thixojoining to produce hybrid components with intermetallic phase

NASA Astrophysics Data System (ADS)

Seyboldt, Christoph; Liewald, Mathias

2018-05-01

Current research activities at the Institute for Metal Forming Technology of the University of Stuttgart are focusing on the manufacturing of hybrid components using semi-solid forming strategies. One process investigated is the joining of different materials in the semi-solid state and is so called "thixojoining". In this process, metallic inlays are inserted into the semi-solid forming die before the actual forming process and are then joined with a material which was heated up to its semi-solid state. Earlier investigations have shown that using this process a very well-shaped form closure can be produced. Furthermore, it was found that sometimes intermetallic phases are built between the different materials, which decisively influence the part properties of such hybrid components for its future application. Within the framework presented in this paper, inlays made of aluminum, brass and steel were joined with aluminum in the semi-solid state. The aim of the investigations was to create an intermetallic bond between the different materials. For this investigations the liquid phase fraction of the aluminum and the temperature of the inlay were varied in order to determine the influence on the formation of the intermetallic phase. Forming trials were performed using a semi-solid forming die with a disk shaped design. Furthermore, the intermetallic phase built was investigated using microsections.

EVALUATION OF FABRIC MEMBRANES FOR USE IN SALTSTONE DRAIN WATER SYSTEM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pickenheim, B.; Miller, D.; Burket, P.

2012-03-08

Saltstone Disposal Unit 2 contains a sheet drain fabric intended to separate solids from drain water to be returned to the Salt Feed Tank. A similar system installed in Vault 4 appears to be ineffective in keeping solids out of the drain water return lines. Waste Solidification Engineering is considering installation of an additional fabric membrane to supplement the existing sheet drain in SDU 2. Amerdrain 200 is the product currently installed in SDU 2. This product is no longer available, so Sitedrain 94 was used as the replacement product in this testing. Fabrics with apparent opening sizes of 10,more » 25, 50 and 100 microns were evaluated. These fabrics were evaluated under three separate test conditions, a water flow test, a solids retention test and a grout pour test. A flow test with water showed that installation of an additional filter layer will predictably reduce the theoretical flux through the sheet drain. The manufacturer reports the flux for Sitedrain 94 as 150 gpm/ft{sup 2} by ASTM D-4491. This compares reasonably well with the 117 gpm/ft{sup 2} obtained in this testing. A combination of the 10 micron fabric with Sitedrain 94 could be expected to decrease flux by about 10 times as compared to Sitedrain 94 alone. The different media were used to filter a slag and fly ash mixture from water. Slag historically has the smallest nominal particle size of the premix components. Cement was omitted from the test because of its reactivity with water would prohibit accurately particle size measurements of the filtered samples. All four media sizes were able to remove greater than 95% of particles larger than 100 microns from the slurry. The smaller opening sizes were increasingly effective in removing more particles. The 10 micron filter captured 15% of the total amount of solids used in the test. This result implies that some insoluble particles may still be able to enter the drain water collection system, although the overall solids rejection is significantly improved over the current design. Test boxes were filled with grout to evaluate the performance of the sheet drain and fabrics in a simulated vault environment. All of the tests produced a similar amount of drain water, between 8-11% of the amount of water in the mix, which is expected with the targeted formulation. All of the collected drain waters contained some amount of solids, although the 10 micron filter did not appear to allow any premix materials to pass through. The solids collected from this box are believed to consist of calcium carbonate based on one ICP-AES measurement. Any of the four candidate fabrics would be an improvement over the sheet drain alone relative to solids removal. The 10 micron fabric is the only candidate that stopped all premix material from passing. The 10 micron fabric will also cause the largest decrease in flux. This decrease in flux was not enough to inhibit the total amount of drain water removed, but may lead to increased time to remove standing water prior to subsequent pours in the facility. The acceptability of reduced liquid flux through the 10 micron fabric will depend on the amount of excess water to be removed, the time available for water removal and the total area of fabric installed at the disposal cell.« less

Effect of storage time of extended-pour and conventional alginate impressions on dimensional accuracy of casts.

PubMed

Rohanian, Ahmad; Ommati Shabestari, Ghasem; Zeighami, Somayeh; Samadi, Mohammad Javad; Shamshiri, Ahmad Reza

2014-11-01

Some manufacturers claim to have produced new irreversible hydro-colloids that are able to maintain their dimensional stability during storage. The present study evaluated the effect of storage time on dimensional stability of three alginates: Hydrogum 5, Tropicalgin and Alginoplast. In this experimental in-vitro trial, a total of 90 alginate impressions were made from a Dentoform model using Hydrogum 5, Tropicalgin and Alginoplast alginates. The impressions were stored in a sealed plastic bag without a damp paper towel for 0, 24, 48, 72 and 120 hours and then poured with type III dental stone. Cross-arch (facial of 6 to facial of 6 on the opposite side) and antero-posterior (distal of right first molar to the ipsilateral central incisor) measurements were made with a digital caliper on the casts. Data were analyzed by two-way and one-way ANOVA and Tukey's post-hoc test (P<0.05). Alginate type and the pouring time significantly affected the dimensional stability of alginate impressions (both Ps<0.001). Pouring of Hydrogum 5 impressions can be delayed for up to 120 hours without significant dimensional changes. Alginoplast impressions may be poured after 72 hours, but Tropicalgin should be poured immediately and the storage time should not be more than 24 hours. Immediate pouring of alginate impressions provides the highest accuracy in reproducing the teeth and adjacent tissues; however, this study demonstrated that pouring may be delayed for up to five days using extended-pour (Hydrogum 5) alginates.

Les métamatériaux, des micro-ondes à l'optique : théorie et applications

NASA Astrophysics Data System (ADS)

Kante, B.

2010-04-01

Cet article constitue une contribution originale et importante à la compréhension à la fois théorique et expérimentale des métamatériaux en micro-ondes et en infrarouge. Nous avons réalisé et caractérisé sur silicium des nano-structures metallo-diélectriques, briques de base des métamatériaux infrarouge et optique. Des caractérisations optiques exhaustives ont été réalisées pour la première fois sur ces structures en amplitude et en phase par interférométrie. Des topologies plus simples de métamatériaux d’un point de vue technologique et des performances optiques ont été introduites, et leur potentiel démontré dans la réalisation de fonctions aussi complexes que la réfraction négative, le couplage de mode plasmoniques, les nano senseurs pour la biologie et l’invisibilité électromagnétique en infrarouge. Les transformations d’espace, et le nouveau paradigme qu’elles offrent à l’optique, rendant possible une ingénierie de l’espace pour les photons ainsi que leur implémentation par métamatériaux ont été présentés par la première démonstration expérimentale d’une cape d’invisibilité non magnétique.

Enthalpy-based multiple-relaxation-time lattice Boltzmann method for solid-liquid phase-change heat transfer in metal foams.

PubMed

Liu, Qing; He, Ya-Ling; Li, Qing

2017-08-01

In this paper, an enthalpy-based multiple-relaxation-time (MRT) lattice Boltzmann (LB) method is developed for solid-liquid phase-change heat transfer in metal foams under the local thermal nonequilibrium (LTNE) condition. The enthalpy-based MRT-LB method consists of three different MRT-LB models: one for flow field based on the generalized non-Darcy model, and the other two for phase-change material (PCM) and metal-foam temperature fields described by the LTNE model. The moving solid-liquid phase interface is implicitly tracked through the liquid fraction, which is simultaneously obtained when the energy equations of PCM and metal foam are solved. The present method has several distinctive features. First, as compared with previous studies, the present method avoids the iteration procedure; thus it retains the inherent merits of the standard LB method and is superior to the iteration method in terms of accuracy and computational efficiency. Second, a volumetric LB scheme instead of the bounce-back scheme is employed to realize the no-slip velocity condition in the interface and solid phase regions, which is consistent with the actual situation. Last but not least, the MRT collision model is employed, and with additional degrees of freedom, it has the ability to reduce the numerical diffusion across the phase interface induced by solid-liquid phase change. Numerical tests demonstrate that the present method can serve as an accurate and efficient numerical tool for studying metal-foam enhanced solid-liquid phase-change heat transfer in latent heat storage. Finally, comparisons and discussions are made to offer useful information for practical applications of the present method.

Development and Validation of HPLC Method for Determination of Crocetin, a constituent of Saffron, in Human Serum Samples.

PubMed

Mohammadpour, Amir Hooshang; Ramezani, Mohammad; Tavakoli Anaraki, Nasim; Malaekeh-Nikouei, Bizhan; Amel Farzad, Sara; Hosseinzadeh, Hossein

2013-01-01

The present study reports the development and validation of a sensitive and rapid extraction method beside high performance liquid chromatographic method for the determination of crocetin in human serum. The HPLC method was carried out by using a C18 reversed-phase column and a mobile phase composed of methanol/water/acetic acid (85:14.5:0.5 v/v/v) at the flow rate of 0.8 ml/min. The UV detector was set at 423 nm and 13-cis retinoic acid was used as the internal standard. Serum samples were pretreated with solid-phase extraction using Bond Elut C18 (200mg) cartridges or with direct precipitation using acetonitrile. The calibration curves were linear over the range of 0.05-1.25 µg/ml for direct precipitation method and 0.5-5 µg/ml for solid-phase extraction. The mean recoveries of crocetin over a concentration range of 0.05-5 µg/ml serum for direct precipitation method and 0.5-5 µg/ml for solid-phase extraction were above 70 % and 60 %, respectively. The intraday coefficients of variation were 0.37- 2.6% for direct precipitation method and 0.64 - 5.43% for solid-phase extraction. The inter day coefficients of variation were 1.69 - 6.03% for direct precipitation method and 5.13-12.74% for solid-phase extraction, respectively. The lower limit of quantification for crocetin was 0.05 µg/ml for direct precipitation method and 0.5 µg/ml for solid-phase extraction. The validated direct precipitation method for HPLC satisfied all of the criteria that were necessary for a bioanalytical method and could reliably quantitate crocetin in human serum for future clinical pharmacokinetic study.

Development and Validation of HPLC Method for Determination of Crocetin, a constituent of Saffron, in Human Serum Samples

PubMed Central

Mohammadpour, Amir Hooshang; Ramezani, Mohammad; Tavakoli Anaraki, Nasim; Malaekeh-Nikouei, Bizhan; Amel Farzad, Sara; Hosseinzadeh, Hossein

2013-01-01

Objective(s): The present study reports the development and validation of a sensitive and rapid extraction method beside high performance liquid chromatographic method for the determination of crocetin in human serum. Materials and Methods: The HPLC method was carried out by using a C18 reversed-phase column and a mobile phase composed of methanol/water/acetic acid (85:14.5:0.5 v/v/v) at the flow rate of 0.8 ml/min. The UV detector was set at 423 nm and 13-cis retinoic acid was used as the internal standard. Serum samples were pretreated with solid-phase extraction using Bond Elut C18 (200mg) cartridges or with direct precipitation using acetonitrile. Results: The calibration curves were linear over the range of 0.05-1.25 µg/ml for direct precipitation method and 0.5-5 µg/ml for solid-phase extraction. The mean recoveries of crocetin over a concentration range of 0.05-5 µg/ml serum for direct precipitation method and 0.5-5 µg/ml for solid-phase extraction were above 70 % and 60 %, respectively. The intraday coefficients of variation were 0.37- 2.6% for direct precipitation method and 0.64 - 5.43% for solid-phase extraction. The inter day coefficients of variation were 1.69 – 6.03% for direct precipitation method and 5.13-12.74% for solid-phase extraction, respectively. The lower limit of quantification for crocetin was 0.05 µg/ml for direct precipitation method and 0.5 µg/ml for solid-phase extraction. Conclusion: The validated direct precipitation method for HPLC satisfied all of the criteria that were necessary for a bioanalytical method and could reliably quantitate crocetin in human serum for future clinical pharmacokinetic study. PMID:23638292

Fabrication of single domain GdBCO bulk superconductors by a new modified TSIG technique

NASA Astrophysics Data System (ADS)

Yang, W. M.; Zhi, X.; Chen, S. L.; Wang, M.; Li, J. W.; Ma, J.; Chao, X. X.

2014-01-01

Single domain GdBCO bulk superconductors have been fabricated with new and traditional solid phases by a top seeded infiltration and growth (TSIG) process technique. In the conventional TSIG process, three types of powders, such as Gd2BaCuO5, GdBa2Cu3O7-x and Ba3Cu5O8, must be prepared, but in our new modified TSIG technique, only BaCuO2 powders are required during the fabrication of the single domain GdBCO bulk superconductors. The solid phase used in the conventional process is Gd2BaCuO5 instead of the solid phase (Gd2O3 + BaCuO2) utilized in the new process. The liquid phase used in the conventional process is a mixture of (GdBa2Cu3O7-x + Ba3Cu5O8), and the liquid phase in the new process is a mixture of (Gd2O3 + 10BaCuO2 + 6CuO). Single domain GdBCO bulk superconductors have been fabricated with the new solid and liquid phases. The levitation force of the GdBCO bulk samples fabricated by the new solid phase is 28 N, which is slightly higher than that of the samples fabricated using the conventional solid phases (26 N). The microstructure and the levitation force of the samples indicate that this new method can greatly simplify the fabrication process, introduce nanometer-sized flux centers, improve the levitation force and working efficiency, and greatly reduce the cost of fabrication of single domain GdBCO bulk superconductors by the TSIG process.

Enthalpy-based multiple-relaxation-time lattice Boltzmann method for solid-liquid phase-change heat transfer in metal foams

NASA Astrophysics Data System (ADS)

Liu, Qing; He, Ya-Ling; Li, Qing

2017-08-01

In this paper, an enthalpy-based multiple-relaxation-time (MRT) lattice Boltzmann (LB) method is developed for solid-liquid phase-change heat transfer in metal foams under the local thermal nonequilibrium (LTNE) condition. The enthalpy-based MRT-LB method consists of three different MRT-LB models: one for flow field based on the generalized non-Darcy model, and the other two for phase-change material (PCM) and metal-foam temperature fields described by the LTNE model. The moving solid-liquid phase interface is implicitly tracked through the liquid fraction, which is simultaneously obtained when the energy equations of PCM and metal foam are solved. The present method has several distinctive features. First, as compared with previous studies, the present method avoids the iteration procedure; thus it retains the inherent merits of the standard LB method and is superior to the iteration method in terms of accuracy and computational efficiency. Second, a volumetric LB scheme instead of the bounce-back scheme is employed to realize the no-slip velocity condition in the interface and solid phase regions, which is consistent with the actual situation. Last but not least, the MRT collision model is employed, and with additional degrees of freedom, it has the ability to reduce the numerical diffusion across the phase interface induced by solid-liquid phase change. Numerical tests demonstrate that the present method can serve as an accurate and efficient numerical tool for studying metal-foam enhanced solid-liquid phase-change heat transfer in latent heat storage. Finally, comparisons and discussions are made to offer useful information for practical applications of the present method.

Patient-related risk factors for urinary retention following ambulatory general surgery: a systematic review and meta-analysis.

PubMed

Mason, Sam E; Scott, Alasdair J; Mayer, Erik; Purkayastha, Sanjay

2016-06-01

Postoperative urinary retention (POUR) is a source of avoidable patient harm. The aim of this review is to identify and quantify the role of patient-related risk factors in the development of POUR following ambulatory general surgery. Studies published until December 2014 were identified by searching MEDLINE, EMBASE, and PsycINFO databases. Risk factors assessed in 3 or more studies were meta-analyzed. Twenty-one studies were suitable for inclusion consisting of 7,802 patients. The incidence of POUR was 14%. Increased age and the presence of lower urinary tract symptoms significantly increased risk with odds ratios [ORs] of 2.11 (95% confidence interval [CI] 1.15 to 3.86) and 2.83 (1.57 to 5.08), respectively. Male sex was not associated with developing POUR (OR .96, 95% CI .62 to 1.50). Preoperative α-blocker use significantly decreased the incidence of POUR with an OR of .37 (95% CI .15 to .91). Increased age and the presence of lower urinary tract symptoms increase the risk of POUR, while α-blocker use confers protection. Male sex was not associated with POUR. These findings assist in preoperative identification of patients at high risk of POUR. Copyright © 2015 Elsevier Inc. All rights reserved.

The Solid Phase Curing Time Effect of Asbuton with Texapon Emulsifier at the Optimum Bitumen Content

NASA Astrophysics Data System (ADS)

Sarwono, D.; Surya D, R.; Setyawan, A.; Djumari

2017-07-01

Buton asphalt (asbuton) could not be utilized optimally in Indonesia. Asbuton utilization rate was still low because the processed product of asbuton still have impracticable form in the term of use and also requiring high processing costs. This research aimed to obtain asphalt products from asbuton practical for be used through the extraction process and not requiring expensive processing cost. This research was done with experimental method in laboratory. The composition of emulsify asbuton were 5/20 grain, premium, texapon, HCl, and aquades. Solid phase was the mixture asbuton 5/20 grain and premium with 3 minutes mixing time. Liquid phase consisted texapon, HCl and aquades. The aging process was done after solid phase mixing process in order to reaction and tie of solid phase mixed become more optimal for high solubility level of asphalt production. Aging variable time were 30, 60, 90, 120, and 150 minutes. Solid and liquid phase was mixed for emulsify asbuton production, then extracted for 25 minutes. Solubility level of asphalt, water level, and asphalt characteristic was tested at extraction result of emulsify asbuton with most optimum ashphal level. The result of analysis tested data asphalt solubility level at extract asbuton resulted 94.77% on 120 minutes aging variable time. Water level test resulted water content reduction on emulsify asbuton more long time on occurring of aging solid phase. Examination of asphalt characteristic at extraction result of emulsify asbuton with optimum asphalt solubility level, obtain specimen that have rigid and strong texture in order that examination result have not sufficient ductility and penetration value.

Alternative Submarine Watch Systems: Recommendation for a New CF Submarine Watch Schedule (Systemes Differents d’Horaire de Garde a Bord des Sous-Marins: Nouvel Horaire Recommande Pour les Sous-Marins des FC)

DTIC Science & Technology

2010-01-01

comparativement à une efficacité cognitive de 96 % pour l’horaire de 1 tour sur trois de quatre heures ainsi que pour l’horaire de 1 tour sur trois de...tour sur 2 (8-4-4-8) comparativement à une efficacité cognitive de 96 % pour l’horaire de 1 tour sur trois de quatre heures ainsi que pour l’horaire...FAST™ (Fatigue Avoidance and Safety Tool), a computer application designed to predict and prevent fatigue in operational settings. The output of FAST

Characterization of rhamnolipids by liquid chromatography/mass spectrometry after solid-phase extraction.

PubMed

Behrens, Beate; Engelen, Jeannine; Tiso, Till; Blank, Lars Mathias; Hayen, Heiko

2016-04-01

Rhamnolipids are surface-active agents with a broad application potential that are produced in complex mixtures by bacteria of the genus Pseudomonas. Analysis from fermentation broth is often characterized by laborious sample preparation and requires hyphenated analytical techniques like liquid chromatography coupled to mass spectrometry (LC-MS) to obtain detailed information about sample composition. In this study, an analytical procedure based on chromatographic method development and characterization of rhamnolipid sample material by LC-MS as well as a comparison of two sample preparation methods, i.e., liquid-liquid extraction and solid-phase extraction, is presented. Efficient separation was achieved under reversed-phase conditions using a mixed propylphenyl and octadecylsilyl-modified silica gel stationary phase. LC-MS/MS analysis of a supernatant from Pseudomonas putida strain KT2440 pVLT33_rhlABC grown on glucose as sole carbon source and purified by solid-phase extraction revealed a total of 20 congeners of di-rhamnolipids, mono-rhamnolipids, and their biosynthetic precursors 3-(3-hydroxyalkanoyloxy)alkanoic acids (HAAs) with different carbon chain lengths from C8 to C14, including three rhamnolipids with uncommon C9 and C11 fatty acid residues. LC-MS and the orcinol assay were used to evaluate the developed solid-phase extraction method in comparison with the established liquid-liquid extraction. Solid-phase extraction exhibited higher yields and reproducibility as well as lower experimental effort.

Separation of phenolic acids from sugarcane rind by online solid-phase extraction with high-speed counter-current chromatography.

PubMed

Geng, Ping; Fang, Yingtong; Xie, Ronglong; Hu, Weilun; Xi, Xingjun; Chu, Qiao; Dong, Genlai; Shaheen, Nusrat; Wei, Yun

2017-02-01

Sugarcane rind contains some functional phenolic acids. The separation of these compounds from sugarcane rind is able to realize the integrated utilization of the crop and reduce environment pollution. In this paper, a novel protocol based on interfacing online solid-phase extraction with high-speed counter-current chromatography (HSCCC) was established, aiming at improving and simplifying the process of phenolic acids separation from sugarcane rind. The conditions of online solid-phase extraction with HSCCC involving solvent system, flow rate of mobile phase as well as saturated extent of absorption of solid-phase extraction were optimized to improve extraction efficiency and reduce separation time. The separation of phenolic acids was performed with a two-phase solvent system composed of butanol/acetic acid/water at a volume ratio of 4:1:5, and the developed online solid-phase extraction with HSCCC method was validated and successfully applied for sugarcane rind, and three phenolic acids including 6.73 mg of gallic acid, 10.85 mg of p-coumaric acid, and 2.78 mg of ferulic acid with purities of 60.2, 95.4, and 84%, respectively, were obtained from 150 mg sugarcane rind crude extracts. In addition, the three different elution methods of phenolic acids purification including HSCCC, elution-extrusion counter-current chromatography and back-extrusion counter-current chromatography were compared. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The analysis of magnesium oxide hydration in three-phase reaction system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Xiaojia; Guo, Lin; Chen, Chen

In order to investigate the magnesium oxide hydration process in gas–liquid–solid (three-phase) reaction system, magnesium hydroxide was prepared by magnesium oxide hydration in liquid–solid (two-phase) and three-phase reaction systems. A semi-empirical model and the classical shrinking core model were used to fit the experimental data. The fitting result shows that both models describe well the hydration process of three-phase system, while only the semi-empirical model right for the hydration process of two-phase system. The characterization of the hydration product using X-Ray diffraction (XRD) and scanning electron microscope (SEM) was performed. The XRD and SEM show hydration process in the two-phasemore » system follows common dissolution/precipitation mechanism. While in the three-phase system, the hydration process undergo MgO dissolution, Mg(OH){sub 2} precipitation, Mg(OH){sub 2} peeling off from MgO particle and leaving behind fresh MgO surface. - Graphical abstract: There was existence of a peeling-off process in the gas–liquid–solid (three-phase) MgO hydration system. - Highlights: • Magnesium oxide hydration in gas–liquid–solid system was investigated. • The experimental data in three-phase system could be fitted well by two models. • The morphology analysis suggested that there was existence of a peel-off process.« less

Ultrasonic detection of solid phase mass flow ratio of pneumatic conveying fly ash

NASA Astrophysics Data System (ADS)

Duan, Guang Bin; Pan, Hong Li; Wang, Yong; Liu, Zong Ming

2014-04-01

In this paper, ultrasonic attenuation detection and weight balance are adopted to evaluate the solid mass ratio in this paper. Fly ash is transported on the up extraction fluidization pneumatic conveying workbench. In the ultrasonic test. McClements model and Bouguer-Lambert-Beer law model were applied to formulate the ultrasonic attenuation properties of gas-solid flow, which can give the solid mass ratio. While in the method of weigh balance, the averaged mass addition per second can reveal the solids mass flow ratio. By contrast these two solid phase mass ratio detection methods, we can know, the relative error is less.

Preparation of l-phenylalanine-imprinted solid-phase extraction sorbent by Pickering emulsion polymerization and the selective enrichment of l-phenylalanine from human urine.

PubMed

Li, Ji; Hu, Xiaoling; Guan, Ping; Zhang, Xiaoyan; Qian, Liwei; Zhang, Nan; Du, Chunbao; Song, Renyuan

2016-05-01

A novel l-phenylalanine molecularly imprinted solid-phase extraction sorbent was synthesized by the combination of Pickering emulsion polymerization and ion-pair dummy template imprinting. Compared to other polymerization methods, the molecularly imprinted polymers thus prepared exhibit a high specific surface, large pore diameter, and appropriate particle size. The key parameters for solid-phase extraction were optimized, and the result indicated that the molecularly imprinted polymer thus prepared exhibits a good recovery of 98.9% for l-phenylalanine. Under the optimized conditions of the procedure, an analytical method for l-phenylalanine was well established. By comparing the performance of the molecularly imprinted polymer and a commercial reverse-phase silica gel, the obtained molecularly imprinted polymer as an solid-phase extraction sorbent is more suitable, exhibiting high precision (relative standard deviation 3.2%, n = 4) and a low limit of detection (60.0 ± 1.9 nmol·L(-1) ) for the isolation of l-phenylalanine. Based on these results, the combination of the Pickering emulsion polymerization and ion-pair dummy template imprinting is effective for preparing selective solid-phase extraction sorbents for the separation of amino acids and organic acids from complex biological samples. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Developpement d'un catalyseur nickel-alumine efficace pour le reformage de diesel a la vapeur d'eau et etude du systeme reactionnel

NASA Astrophysics Data System (ADS)

Fauteux-Lefebvre, Clemence

Le developpement de sources d'energie alternatives fiables et efficaces est aujourd'hui une necessite. L' interet dans le reformage d'hydrocarbures liquides est ainsi croissant puisqu'il s'agit d'une voie pour l'alimentation des piles a combustible. Les piles a combustible ont une efficacite pour la conversion d'energie en electricite plus grande que celle des moteurs a combustion et font ainsi partie de la recherche de solution en efficacite energetique. Ces piles consomment de l'hydrogene comme combustible pour produire de l'electricite, d'ou l'interet pour le reformage. En effet, cette reaction permet de produire de l'hydrogene et du monoxyde de carbone (un autre combustible des piles a combustible a electrolyte solide) a partir d'hydrocarbure liquide, notamment le diesel. Les piles pourraient donc etre integrees avec une unite de reformage leur fournissant directement le combustible necessaire a partir de diesel. Dans ce projet de recherche, un nouveau catalyseur de nickel sous forme de spinelle nickel-alumine (spinelle NiAl2O4 sur support d'alumine et de zircone stabilisee avec yttria) a ete developpe et teste en laboratoire pour du reformage de propane, d'hydrocarbures liquides et de diesel, a la vapeur d'eau. Par ailleurs, une methode d'ajout des reactifs novatrice a ete utilisee afin de diminuer la pyrolyse precedant le reformage, en utilisant une emulsion. Les resultats de reformage d'hydrocarbures purs ont montre des concentrations tres pres de l'equilibre thermodynamique et une activite constante sans desactivation du catalyseur ni formation de carbone, et ce avec des ratios H2O/C de moins de 2.5 et des temperatures d'operation variant entre 630 °C et 750 °C. Lors de tests effectues en utilisant du diesel fossile, a 705°C, avec un debit volumique des reactifs de plus de 50 000 cm3gcat-1h-1 et un ratio H2O/C de moins de 2.5, l'activite a ete maintenue pendant plus de 15 heures, malgre une operation en cycles. L'analyse du catalyseur apres cette utilisation n'a montre aucun carbone significatif sur la surface.- En comparaison, un catalyseur de nickel metallique sur support d'Al2O3 et YSZ a ete utilise dans des conditions similaires. Il y a eu desactivation du catalyseur et obstruction du reacteur par du carbone apres trois heures d'operation. L'analyse de ce catalyseur a permis de verifier qu'il etait recouvert de carbone en filament. L'analyse du systeme reactionnel a montre que la reaction est controlee par la reaction de. surface et non par le transfert de masse. Par ailleurs, les analyses des catalyseurs de spinelle ont demontre qu'il n'y avait pas de modification de sa forme chimique ni de reduction du spinelle en nickel metallique apres l'utilisation. Mots cles : Reformage a la vapeur, diesel, hydrocarbure liquide, catalyseur, spinelle nickel-alumine, equilibre thermodynamique

CCCT - NCTN Steering Committees - Pediatric and Adolescent Tumor

Cancer.gov

The Pediatric and Adolescent Solid Tumor Steering Committee addresses the design, prioritization and evaluation of concepts for large phase 2 and phase 3 clinical trials in extracranial solid tumors of children and youth.

A novel approach to model the transient behavior of solid-oxide fuel cell stacks

NASA Astrophysics Data System (ADS)

Menon, Vikram; Janardhanan, Vinod M.; Tischer, Steffen; Deutschmann, Olaf

2012-09-01

This paper presents a novel approach to model the transient behavior of solid-oxide fuel cell (SOFC) stacks in two and three dimensions. A hierarchical model is developed by decoupling the temperature of the solid phase from the fluid phase. The solution of the temperature field is considered as an elliptic problem, while each channel within the stack is modeled as a marching problem. This paper presents the numerical model and cluster algorithm for coupling between the solid phase and fluid phase. For demonstration purposes, results are presented for a stack operated on pre-reformed hydrocarbon fuel. Transient response to load changes is studied by introducing step changes in cell potential and current. Furthermore, the effect of boundary conditions and stack materials on response time and internal temperature distribution is investigated.

360-degrees profilometry using strip-light projection coupled to Fourier phase-demodulation.

PubMed

Servin, Manuel; Padilla, Moises; Garnica, Guillermo

2016-01-11

360 degrees (360°) digitalization of three dimensional (3D) solids using a projected light-strip is a well-established technique in academic and commercial profilometers. These profilometers project a light-strip over the digitizing solid while the solid is rotated a full revolution or 360-degrees. Then, a computer program typically extracts the centroid of this light-strip, and by triangulation one obtains the shape of the solid. Here instead of using intensity-based light-strip centroid estimation, we propose to use Fourier phase-demodulation for 360° solid digitalization. The advantage of Fourier demodulation over strip-centroid estimation is that the accuracy of phase-demodulation linearly-increases with the fringe density, while in strip-light the centroid-estimation errors are independent. Here we proposed first to construct a carrier-frequency fringe-pattern by closely adding the individual light-strip images recorded while the solid is being rotated. Next, this high-density fringe-pattern is phase-demodulated using the standard Fourier technique. To test the feasibility of this Fourier demodulation approach, we have digitized two solids with increasing topographic complexity: a Rubik's cube and a plastic model of a human-skull. According to our results, phase demodulation based on the Fourier technique is less noisy than triangulation based on centroid light-strip estimation. Moreover, Fourier demodulation also provides the amplitude of the analytic signal which is a valuable information for the visualization of surface details.

Phase Relations in Ternary Systems in the Subsolidus Region: Methods to Formulate Solid Solution Equations and to Find Particular Compositions

ERIC Educational Resources Information Center

Alvarez-Montan~o, Victor E.; Farías, Mario H.; Brown, Francisco; Mun~oz-Palma, Iliana C.; Cubillas, Fernando; Castillon-Barraza, Felipe F.

2017-01-01

A good understanding of ternary phase diagrams is required to advance and/or to reproduce experimental research in solid-state and materials chemistry. The aim of this paper is to describe the solutions to problems that appear when studying or determining ternary phase diagrams. A brief description of the principal features shown in phase diagrams…

Heterogeneous fuel for hybrid rocket

NASA Technical Reports Server (NTRS)

Stickler, David B. (Inventor)

1996-01-01

Heterogeneous fuel compositions suitable for use in hybrid rocket engines and solid-fuel ramjet engines, The compositions include mixtures of a continuous phase, which forms a solid matrix, and a dispersed phase permanently distributed therein. The dispersed phase or the matrix vaporizes (or melts) and disperses into the gas flow much more rapidly than the other, creating depressions, voids and bumps within and on the surface of the remaining bulk material that continuously roughen its surface, This effect substantially enhances heat transfer from the combusting gas flow to the fuel surface, producing a correspondingly high burning rate, The dispersed phase may include solid particles, entrained liquid droplets, or gas-phase voids having dimensions roughly similar to the displacement scale height of the gas-flow boundary layer generated during combustion.

Liquid?solid helium interface: some conceptual questions

NASA Astrophysics Data System (ADS)

Leggett, A. J.

2003-12-01

I raise, and discuss qualitatively, some conceptual issues concerning the interface between the crystalline solid and superfluid liquid phases of 4He emphasizing, in particular, the fact that the ground-state wave functions of the two phases are prima facie qualitatively quite different, in that the superfluid liquid phase possesses off-diagonal long-range order (ODLRO), while the crystalline solid does not. The fact that the statics and dynamics of the interface do not appear to be particularly sensitive to the presence of ODLRO in the liquid is tentatively explained by the fact that because of a subtlety associated with the Bose statistics obeyed by the atoms, the solid and liquid wave functions are not locally very different.

Isolation and recovery of selected polybrominated diphenyl ethers from human serum and sheep serum: coupling reversed-phase solid-phase disk extraction and liquid-liquid extraction techniques with a capillary gas chromatographic electron capture negative ion mass spectrometric determinative technique.

PubMed

Loconto, Paul R; Isenga, David; O'Keefe, Michael; Knottnerus, Mark

2008-01-01

Polybrominated diphenyl ethers (PBDEs) are isolated and recovered with acceptable percent recoveries from human serum via liquid-liquid extraction and column chromatographic cleanup and fractionation with quantitation using capillary gas chromatography-mass spectrometry with electron capture negative ion and selected ion monitoring. PBDEs are found in unspiked serum. An alternative sample preparation approach is developed using sheep serum that utilizes a formic acid pre-treatment followed by reversed-phase solid-phase disk extraction and normal-phase solid-phase cleanup using acidified silica gel that yields>50% recoveries. When these percent recoveries are combined with a minimized phase ratio for human serum and very low instrument detection limits, method detection limits below 500 parts-per-trillion are realized.

A model for a transition from a quasicrystalline to a microcrystalline state

NASA Astrophysics Data System (ADS)

Coddens, G.; Launois, P.

1991-07-01

We propose a monoatomic model for a quasicrystal transition as observed recently in systems with icosahedral [3] and decagonal [5] symmetry. It is developed here for the case of decagonal symmetry and is inspired by the experimental results on the system Al-Cu-Co-Si [5,6]. The model goes beyond the purely geometrical description by an important physical aspect: the transition mediates through a single atomic jump distance such that only one unique double-well potential has to be invoked to describe it; in conformity with the symmetry there are 10 jump vectors. In the framework of the model, the microcrystalline state is energetically more favourable than a monocrystalline approximant phase. Nous proposons un modèle mono-atomique pour une transition quasicristal-microcristal du type de celles observées récemment dans des systèmes à symétrie icosaédrique [3] et décagonale [5]. Il est développé ici pour la symétrie décagonale et est inspiré par des résultats expérimentaux concernant l'alliage Al-Cu-Co-Si [5,6]. Le modèle va au-delà d'une description purement géometrique par un aspect physique important : la transition se fait via une seule distance de saut inter-atomique de telle sorte q'un seul double-puits de potentiel doit être pris en compte ; conformément à la symétrie, il y a 10 directions de saut. Dans le cadre du modèle, la phase microcristalline est énergétiquement favorisée par rapport à une phase approximante monocristalline.

On the roles of solid wall in the thermal analysis of micro heat pipes

NASA Astrophysics Data System (ADS)

Hung, Yew Mun

Micro heat pipe is a small-scale passive heat transfer device of very high thermal conductance that uses phase change and circulation of its working fluid to transfer thermal energy. Different from conventional heat pipe, a micro heat pipe does not contain any wick structure. In this thesis, a one-dimensional, steady-state mathematical model of a single triangular micro heat pipe is developed, with the main purpose of establishing a series of analytical studies on the roles of the solid wall of micro heat pipes in conjunction with the characterization of the thermal performance under the effects of various design and operational parameters. The energy equation of the solid wall is solved analytically to obtain the temperature distribution. The liquid phase is coupled with the solid wall through the continuity of heat flux at their interface, and the continuity, momentum and energy equations of the liquid and vapour phases, together with the Young-Laplace equation for capillary pressure, are solve numerically to yield the heat and fluid flow characteristics of the micro heat pipe. By coupling this mathematical model with the phase-change interfacial resistance model, the relationships for the axial temperature distributions of the liquid and vapour phases throughout the longitudinal direction of a micro heat pipe are also formulated. Four major aspects associated with the operational performance of micro heat pipes are discussed. Firstly, the investigation of the effects of axial conduction in the solid wall reveals that the presence of the solid wall induces change in the phase-change heat transport of the working fluid besides facilitating axial heat conduction in the solid wall. The analysis also highlights the effects of the thickness and thermal conductivity of the solid wall on the axial temperature distribution of solid wall, in the wake of the effects of the axial heat conduction induced on the phase-change heat transport of the working fluid. Secondly, analysis on thermal performance and physical phenomena of an overloaded micro heat pipes incorporating the effects of axial conduction in the solid wall is carried out. The thermal effects of the solid material are investigated and it is observed that the behaviour of the solid wall temperature distribution varies drastically as the applied heat load exceeds the heat transport capacity. The abrupt change in the temperature profile of an overloaded micro heat pipe is of considerable practical significance in which the occurrence of dryout can be identified by physically measuring the solid wall temperatures along the axial direction. Thirdly, by taking into account the axial conduction in the solid wall, the effect of gravity on the thermal performance of an inclined micro heat pipe is explored. Attributed to the occurrence of dryout, an abrupt temperature rise is observed at the evaporator end when the micro heat pipe is negatively inclined. Therefore, the orientation of a micro heat pipe can be determined by physically measuring the solid wall temperature. Lastly, by coupling the heat transfer model of phase-change phenomena at the liquid-vapour interface, the model with axial conduction in the solid wall of the micro heat pipe is extended to predict the axial liquid and vapour temperature distributions of the working fluid, which is useful for the verification of certain assumptions made in the derivation of the mathematical model besides for analyzing the heat transfer characteristics of the evaporation process.

Solid-state harmonics beyond the atomic limit.

PubMed

Ndabashimiye, Georges; Ghimire, Shambhu; Wu, Mengxi; Browne, Dana A; Schafer, Kenneth J; Gaarde, Mette B; Reis, David A

2016-06-23

Strong-field laser excitation of solids can produce extremely nonlinear electronic and optical behaviour. As recently demonstrated, this includes the generation of high harmonics extending into the vacuum-ultraviolet and extreme-ultraviolet regions of the electromagnetic spectrum. High harmonic generation is shown to occur fundamentally differently in solids and in dilute atomic gases. How the microscopic mechanisms in the solid and the gas differ remains a topic of intense debate. Here we report a direct comparison of high harmonic generation in the solid and gas phases of argon and krypton. Owing to the weak van der Waals interaction, rare (noble)-gas solids are a near-ideal medium in which to study the role of high density and periodicity in the generation process. We find that the high harmonic generation spectra from the rare-gas solids exhibit multiple plateaus extending well beyond the atomic limit of the corresponding gas-phase harmonics measured under similar conditions. The appearance of multiple plateaus indicates strong interband couplings involving multiple single-particle bands. We also compare the dependence of the solid and gas harmonic yield on laser ellipticity and find that they are similar, suggesting the importance of electron-hole recollision in these solids. This implies that gas-phase methods such as polarization gating for attosecond pulse generation and orbital tomography could be realized in solids.

Advanced Beamformers for 3D Ultrasound Systems Deploying Linear and Planar Phased Array Probes

DTIC Science & Technology

2002-05-01

6tude sur la technologic d𔄀chographie 4D serviront de fondement important A l’innovation dans Ie secteur industriel canadien des dispositifs A...pouvant &tre utilis6 sur place A des fins de diagnostic. La technologie proposee comprend les travaux suivants: "* techniques de formation de faisceaux...faciliter l’imagerie durant les operations avec effraction minimale effectu6es sur place; "* concept d’impulsions A inversion temporelle pour les signaux

Risk Assessment References: Documented Literature Search

DTIC Science & Technology

2012-10-01

the Minister of National Defence, 2012 © Sa Majesté la Reine (en droit du Canada), telle que représentée par le ministre de la Défense nationale...vise à démontrer la valeur de l’approche scientifique pour améliorer les capacités de gestion des situations d’urgence en se concentrant sur...l’évaluation des risques et les infrastructures essentielles. Au cours de la première phase du projet, RDDC a effectué une analyse documentaire

Endobronchial Photoacoustic Microscopy for Staging of Lung Cancer

DTIC Science & Technology

2015-06-01

polydimethylsiloxane ( PDMS ) membrane, which is bio-compatible and can make a seamless contact with the trachea wall. When the tissues receive the pulsed...illustrated in figures 1 (a)-1(e). The mold can be printed by a 3-D printer (Objet Eden 260V). Liquid-phase PDMS is poured into the mold, and after 40...minutes baking at 80 degree Celsius the PDMS can be hardened. Then it is peeled off from the mold and bonded with another piece of PDMS membrane. The

Successful Initial Development of Styrene Substitutes and Suppressants for Vinyl Ester Resin Formulations

DTIC Science & Technology

2003-08-01

into a separatory funnel. Distilled water was added to remove the acid from the ether phase. The layers were allowed to separate, and the water layer...The reaction mixtures were removed from the heat 2 hr after the last acrylic acid aliquot was added. The acrylated oils were purified via ether... remove inhibitor and any unreacted acid , the reaction mixture was ether extracted (25). The mixture was dissolved in diethyl ether and poured into a

A Projection of the Characteristics of Group 4 Facsimile Equipment.

DTIC Science & Technology

1981-02-01

et de transfert quasi nu[ pour i compression d’impulsion donnd A cc genre de f <cJ ci! etf fo +Af. fitre ne modiflant pas Ia phase filtre adaptd : Ia...be used on the public telephone network where an DD, 1473k EiTiow or, Nov6 s OBSOLETE SECURITY CLASSIFICATION OF TN;S PAGE (When De E...are not necessarily visible to host computers attached to the network. Datagram: A finite length packet of data together with des - tination host

Effect of Storage Time of Extended-Pour and Conventional Alginate Impressions on Dimensional Accuracy of Casts

PubMed Central

Rohanian, Ahmad; Ommati Shabestari, Ghasem; Zeighami, Somayeh; Samadi, Mohammad Javad; Shamshiri, Ahmad Reza

2014-01-01

Objectives: Some manufacturers claim to have produced new irreversible hydro-colloids that are able to maintain their dimensional stability during storage. The present study evaluated the effect of storage time on dimensional stability of three alginates: Hydrogum 5, Tropicalgin and Alginoplast. Materials and Methods: In this experimental in-vitro trial, a total of 90 alginate impressions were made from a Dentoform model using Hydrogum 5, Tropicalgin and Alginoplast alginates. The impressions were stored in a sealed plastic bag without a damp paper towel for 0, 24, 48, 72 and 120 hours and then poured with type III dental stone. Cross-arch (facial of 6 to facial of 6 on the opposite side) and antero-posterior (distal of right first molar to the ipsilateral central incisor) measurements were made with a digital caliper on the casts. Data were analyzed by two-way and one-way ANOVA and Tukey’s post-hoc test (P<0.05). Results: Alginate type and the pouring time significantly affected the dimensional stability of alginate impressions (both Ps<0.001). Pouring of Hydrogum 5 impressions can be delayed for up to 120 hours without significant dimensional changes. Alginoplast impressions may be poured after 72 hours, but Tropicalgin should be poured immediately and the storage time should not be more than 24 hours. Conclusion: Immediate pouring of alginate impressions provides the highest accuracy in reproducing the teeth and adjacent tissues; however, this study demonstrated that pouring may be delayed for up to five days using extended-pour (Hydrogum 5) alginates. PMID:25628695

A phase-field approach to nonequilibrium phase transformations in elastic solids via an intermediate phase (melt) allowing for interface stresses.

PubMed

Momeni, Kasra; Levitas, Valery I

2016-04-28

A phase-field approach for phase transformations (PTs) between three different phases at nonequilibrium temperatures is developed. It includes advanced mechanics, thermodynamically consistent interfacial stresses, and interface interactions. A thermodynamic Landau-Ginzburg potential developed in terms of polar order parameters satisfies the desired instability and equilibrium conditions for homogeneous phases. The interfacial stresses were introduced with some terms from large-strain formulation even though the small-strain assumption was utilized. The developed model is applied to study the PTs between two solid phases via a highly disordered intermediate phase (IP) or an intermediate melt (IM) hundreds of degrees below the melting temperature. In particular, the β ↔ δ PTs in HMX energetic crystals via IM are analyzed. The effects of various parameters (temperature, ratios of widths and energies of solid-solid (SS) to solid-melt (SM) interfaces, elastic energy, and interfacial stresses) on the formation, stability, and structure of the IM within a propagating SS interface are studied. Interfacial and elastic stresses within a SS interphase and their relaxation and redistribution with the appearance of a partial or complete IM are analyzed. The energy and structure of the critical nucleus (CN) of the IM are studied as well. In particular, the interfacial stresses increase the aspect-ratio of the CN. Although including elastic energy can drastically reduce the energy of the CN of the IM, the activation energy of the CN of the IM within the SS interface increases when interfacial tension is taken into account. The developed thermodynamic potential can also be modified to model other multiphase physical phenomena, such as multi-variant martensitic PTs, grain boundary and surface-induced pre-melting and PTs, as well as developing phase diagrams for IPs.

Kinetics of microbial reduction of Solid phase U(VI).

PubMed

Liu, Chongxuan; Jeon, Byong-Hun; Zachara, John M; Wang, Zheming; Dohnalkova, Alice; Fredrickson, James K

2006-10-15

Sodium boltwoodite (NaUO2SiO3OH x 1.5 H2O) was used to assess the kinetics of microbial reduction of solid-phase U(VI) by a dissimilatory metal-reducing bacterium (DMRB), Shewanella oneidensis strain MR-1. The bioreduction kinetics was studied with Na-boltwoodite in suspension or within alginate beads in a nongrowth medium with lactate as electron donor at pH 6.8 buffered with PIPES. Concentrations of U(VI)tot and cell number were varied to evaluate the coupling of U(VI) dissolution, diffusion, and microbial activity. Microscopic and spectroscopic analyses with transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), and laser-induced fluorescence spectroscopy (LIFS) collectively indicated that solid-phase U(VI) was first dissolved and diffused out of grain interiors before it was reduced on bacterial surfaces and/or within the periplasm. The kinetics of solid-phase U(VI) bioreduction was well described by a coupled model of bicarbonate-promoted dissolution of Na-boltwoodite, intragrain uranyl diffusion, and Monod type bioreduction kinetics with respect to dissolved U(VI) concentration. The results demonstrated that microbial reduction of solid-phase U(VI) is controlled by coupled biological, chemical, and physical processes.

Two-dimensional ice mapping of molecular cores

NASA Astrophysics Data System (ADS)

Noble, J. A.; Fraser, H. J.; Pontoppidan, K. M.; Craigon, A. M.

2017-06-01

We present maps of the column densities of H2O, CO2 and CO ices towards the molecular cores B 35A, DC 274.2-00.4, BHR 59 and DC 300.7-01.0. These ice maps, probing spatial distances in molecular cores as low as 2200 au, challenge the traditional hypothesis that the denser the region observed, the more ice is present, providing evidence that the relationships between solid molecular species are more varied than the generic picture we often adopt to model gas-grain chemical processes and explain feedback between solid phase processes and gas phase abundances. We present the first combined solid-gas maps of a single molecular species, based upon observations of both CO ice and gas phase C18O towards B 35A, a star-forming dense core in Orion. We conclude that molecular species in the solid phase are powerful tracers of 'small-scale' chemical diversity, prior to the onset of star formation. With a component analysis approach, we can probe the solid phase chemistry of a region at a level of detail greater than that provided by statistical analyses or generic conclusions drawn from single pointing line-of-sight observations alone.

Dual-phase Cr-Ta alloys for structural applications

DOEpatents

Liu, Chain T.; Brady, Michael P.; Zhu, Jiahong; Tortorelli, Peter F.

2001-01-01

Dual phase alloys of chromium containing 2 to 11 atomic percent tantalum with minor amounts of Mo, Cr, Ti, Y, La, Cr, Si and Ge are disclosed. These alloys contain two phases including Laves phase and Cr-rich solid solution in either eutectic structures or dispersed Laves phase particles in the Cr-rich solid solution matrix. The alloys have superior mechanical properties at high temperature and good oxidation resistance when heated to above 1000.degree. C. in air.

Modelling Phase Transition Phenomena in Fluids

DTIC Science & Technology

2015-07-01

Sublimation line r @@I Triple point ? Vapourisation liner @@I Critical point -Fusion line Solid Liquid Gas Figure 1: Schematic of a phase diagram means that the...velocity field can be set zero, and only the balance of energy constitutes the Stefan model. In contrast to this the liquid - gas phase transitions...defined by requiring that the phase-transition line is crossed in a direction from solid to liquid or from liquid to gas (vapour) phases. The term T∗ δs is

Characterisation of chamomile volatiles by simultaneous distillation solid-phase extraction in comparison to hydrodistillation and simultaneous distillation extraction.

PubMed

Krüger, Hans

2010-05-01

A new method for complete separation of steam-volatile organic compounds is described using the example of chamomile flowers. This method is based on the direct combination of hydrodistillation and solid-phase extraction in a circulation apparatus. In contrast to hydrodistillation and simultaneous distillation extraction (SDE), an RP-18 solid phase as adsorptive material is used rather than a water-insoluble solvent. Therefore, a prompt and complete fixation of all volatiles takes place, and the circulation of water-soluble bisabololoxides as well as water-soluble and thermolabile en-yne-spiroethers is inhibited. This so-called simultaneous distillation solid-phase extraction (SD-SPE) provides extracts that better characterise the real composition of the vapour phase, as well as the composition of inhalation vapours, than do SDE extracts or essential oils obtained by hydrodistillation. The data indicate that during inhalation therapy with chamomile, the bisabololoxides and spiroethers are more strongly involved in the inhaling activity than so far assumed. Georg Thieme Verlag KG Stuttgart New York.

Silicon nitride equation of state

NASA Astrophysics Data System (ADS)

Brown, Robert C.; Swaminathan, Pazhayannur K.

2017-01-01

This report presents the development of a global, multi-phase equation of state (EOS) for the ceramic silicon nitride (Si3N4).1 Structural forms include amorphous silicon nitride normally used as a thin film and three crystalline polymorphs. Crystalline phases include hexagonal α-Si3N4, hexagonal β-Si3N4, and the cubic spinel c-Si3N4. Decomposition at about 1900 °C results in a liquid silicon phase and gas phase products such as molecular nitrogen, atomic nitrogen, and atomic silicon. The silicon nitride EOS was developed using EOSPro which is a new and extended version of the PANDA II code. Both codes are valuable tools and have been used successfully for a variety of material classes. Both PANDA II and EOSPro can generate a tabular EOS that can be used in conjunction with hydrocodes. The paper describes the development efforts for the component solid phases and presents results obtained using the EOSPro phase transition model to investigate the solid-solid phase transitions in relation to the available shock data that have indicated a complex and slow time dependent phase change to the c-Si3N4 phase. Furthermore, the EOSPro mixture model is used to develop a model for the decomposition products; however, the need for a kinetic approach is suggested to combine with the single component solid models to simulate and further investigate the global phase coexistences.

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING OF CONCRETE

NASA Technical Reports Server (NTRS)

1975-01-01

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING OF CONCRETE KSC-375C-10036.31 108-KSC-375C-10036.31, P-21426, ARCHIVE-04502 Aerial oblique of Shuttle runway facilities. Pouring concrete on runway. Direction north - altitude 100'.

High temperature lubricating process

DOEpatents

Taylor, R.W.; Shell, T.E.

1979-10-04

It has been difficult to provide adequate lubrication for load bearing, engine components when such engines are operating in excess of about 475/sup 0/C. The present invention is a process for providing a solid lubricant on a load bearing, solid surface, such as in an engine being operated at temperatures in excess of about 475/sup 0/C. The process comprises contacting and maintaining the following steps: a gas phase is provided which includes at least one component reactable in a temperature dependent reaction to form a solid lubricant; the gas phase is contacted with the load bearing surface; the load bearing surface is maintained at a temperature which causes reaction of the gas phase component and the formation of the solid lubricant; and the solid lubricant is formed directly on the load bearing surface. The method is particularly suitable for use with ceramic engines.

High temperature lubricating process

DOEpatents

Taylor, Robert W.; Shell, Thomas E.

1982-01-01

It has been difficult to provide adaquate lubrication for load bearing, engine components when such engines are operating in excess of about 475.degree. C. The present invention is a process for providing a solid lubricant on a load bearing, solid surface (14), such as in an engine (10) being operated at temperatures in excess of about 475.degree. C. The process comprises contacting and maintaining steps. A gas phase (42) is provided which includes at least one component reactable in a temperature dependent reaction to form a solid lubricant. The gas phase is contacted with the load bearing surface. The load bearing surface is maintained at a temperature which causes reaction of the gas phase component and the formation of the solid lubricant. The solid lubricant is formed directly on the load bearing surface. The method is particularly suitable for use with ceramic engines.

A study of room-temperature LixMn1.5Ni0.5O4 solid solutions

NASA Astrophysics Data System (ADS)

Saravanan, Kuppan; Jarry, Angelique; Kostecki, Robert; Chen, Guoying

2015-01-01

Understanding the kinetic implication of solid-solution vs. biphasic reaction pathways is critical for the development of advanced intercalation electrode materials. Yet this has been a long-standing challenge in materials science due to the elusive metastable nature of solid solution phases. The present study reports the synthesis, isolation, and characterization of room-temperature LixMn1.5Ni0.5O4 solid solutions. In situ XRD studies performed on pristine and chemically-delithiated, micron-sized single crystals reveal the thermal behavior of LixMn1.5Ni0.5O4 (0 <= x <= 1) cathode material consisting of three cubic phases: LiMn1.5Ni0.5O4 (Phase I), Li0.5Mn1.5Ni0.5O4 (Phase II) and Mn1.5Ni0.5O4 (Phase III). A phase diagram capturing the structural changes as functions of both temperature and Li content was established. The work not only demonstrates the possibility of synthesizing alternative electrode materials that are metastable in nature, but also enables in-depth evaluation on the physical, electrochemical and kinetic properties of transient intermediate phases and their role in battery electrode performance.

Solid-Solid Phase Transition Kinetics of FOX-7

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burnham, A K; Weese, R K; Wang, R

Since it was developed in the late 1990s, 1,1-diamino-2,2-dinitroethene (FOX-7), with lower sensitivity and comparable performance to RDX, has received increasing interest. This paper will present our results for the phase changes of FOX-7 using DSC and HFC (Heat Flow Calorimetry). DSC thermal curves recorded at linear heating rates of 0.10, 0.35 and 1.0 C min{sup -1} show two endothermic peaks and two exothermic peaks. The two endothermic peaks represent solid-solid phase transitions, which have been observed in the literature at 114 C ({beta}-{gamma}) and 159 C ({gamma}-{delta}) by both DSC and XPD (X-ray powder diffraction) measurements. The first transitionmore » shifts from 114.5 to 115.8 C as the heating rate increases from 0.10 to 1.0 C min{sup -1}, while the second transition shifts from 158.5 to 160.4 C. Cyclical heating experiments show the endotherms and exotherms for a first heating through the {gamma} phase to the {delta} phase, a cooling and reversion to the {alpha} or {beta} phase, and a second heating to the {gamma} and {delta} phases. The data are interpreted using kinetic models with thermodynamic constraints.« less

The Gaseous Phase as a Probe of the Astrophysical Solid Phase Chemistry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abou Mrad, Ninette; Duvernay, Fabrice; Isnard, Robin

2017-09-10

In support of space missions and spectroscopic observations, laboratory experiments on ice analogs enable a better understanding of organic matter formation and evolution in astrophysical environments. Herein, we report the monitoring of the gaseous phase of processed astrophysical ice analogs to determine if the gaseous phase can elucidate the chemical mechanisms and dominant reaction pathways occurring in the solid ice subjected to vacuum ultra-violet (VUV) irradiation at low temperature and subsequently warmed. Simple (CH{sub 3}OH), binary (H{sub 2}O:CH{sub 3}OH, CH{sub 3}OH:NH{sub 3}), and ternary ice analogs (H{sub 2}O:CH{sub 3}OH:NH{sub 3}) were VUV-processed and warmed. The evolution of volatile organic compoundsmore » in the gaseous phase shows a direct link between their relative abundances in the gaseous phase, and the radical and thermal chemistries modifying the initial ice composition. The correlation between the gaseous and solid phases may play a crucial role in deciphering the organic composition of astrophysical objects. As an example, possible solid compositions of the comet Lovejoy are suggested using the abundances of organics in its comae.« less

Solid Surface Combustion Experiment

NASA Image and Video Library

1994-09-12

STS064-10-011 (12 Sept. 1994) --- The Solid Surface Combustion Experiment (SSCE), designed to supply information on flame spread over solid fuel surfaces in the reduced-gravity environment of space, is pictured during flight day four operations. The middeck experiment measured the rate of spreading, the solid-phase temperature, and the gas-phase temperature of flames spreading over rectangular fuel beds. STS-64 marked the seventh trip into space for the Lewis Research Center experiment. Photo credit: NASA or National Aeronautics and Space Administration

p-Adic solid-on-solid model on a Cayley tree

NASA Astrophysics Data System (ADS)

Khakimov, O. N.

2017-12-01

We consider a p-adic solid-on-solid ( SOS) model with a nearest-neighbor coupling, m+1 spins, and a coupling constant J ∈ Q p on a Cayley tree. We find conditions under which a phase transition does not occur in the model. We show that if p | m + 1 for some J, then a phase transition occurs. Moreover, we formulate a criterion for the boundedness of p-adic Gibbs measures for the ( m+1)- state SOS model.

A contribution to the knowledge of HMX decomposition and application of results. [at atmospheric pressure

NASA Technical Reports Server (NTRS)

Kraeutle, K. J.

1980-01-01

The decomposition of cyclotramethylenetetranitramine (HMX) in the solid and liquid phase was studied by isothermal and nonisothermal heating at atmospheric pressure. Decomposition rates of solid HMX changed with sample size and gaseous environment. Kinetic parameters were obtained from weight loss measurements in the temperature range 229 C - 269 C. These tests also yielded highly porous solid residues. Qualitative aspects of solid and liquid phase decomposition of HMX with additives were also investigated in isothermal and nonisothermal tests.

Modeling of Thermal Phase Noise in a Solid Core Photonic Crystal Fiber-Optic Gyroscope.

PubMed

Song, Ningfang; Ma, Kun; Jin, Jing; Teng, Fei; Cai, Wei

2017-10-26

A theoretical model of the thermal phase noise in a square-wave modulated solid core photonic crystal fiber-optic gyroscope has been established, and then verified by measurements. The results demonstrate a good agreement between theory and experiment. The contribution of the thermal phase noise to the random walk coefficient of the gyroscope is derived. A fiber coil with 2.8 km length is used in the experimental solid core photonic crystal fiber-optic gyroscope, showing a random walk coefficient of 9.25 × 10 -5 deg/√h.

Structure and transport properties of a plastic crystal ion conductor: diethyl(methyl)(isobutyl)phosphonium hexafluorophosphate.

PubMed

Jin, Liyu; Nairn, Kate M; Forsyth, Craig M; Seeber, Aaron J; MacFarlane, Douglas R; Howlett, Patrick C; Forsyth, Maria; Pringle, Jennifer M

2012-06-13

Understanding the ion transport behavior of organic ionic plastic crystals (OIPCs) is crucial for their potential application as solid electrolytes in various electrochemical devices such as lithium batteries. In the present work, the ion transport mechanism is elucidated by analyzing experimental data (single-crystal XRD, multinuclear solid-state NMR, DSC, ionic conductivity, and SEM) as well as the theoretical simulations (second moment-based solid static NMR line width simulations) for the OIPC diethyl(methyl)(isobutyl)phosphonium hexafluorophosphate ([P(1,2,2,4)][PF(6)]). This material displays rich phase behavior and advantageous ionic conductivities, with three solid-solid phase transitions and a highly "plastic" and conductive final solid phase in which the conductivity reaches 10(-3) S cm(-1). The crystal structure shows unique channel-like packing of the cations, which may allow the anions to diffuse more easily than the cations at lower temperatures. The strongly phase-dependent static NMR line widths of the (1)H, (19)F, and (31)P nuclei in this material have been well simulated by different levels of molecular motions in different phases. Thus, drawing together of the analytical and computational techniques has allowed the construction of a transport mechanism for [P(1,2,2,4)][PF(6)]. It is also anticipated that utilization of these techniques will allow a more detailed understanding of the transport mechanisms of other plastic crystal electrolyte materials.

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING CONCRETE ON RUNWAY

NASA Technical Reports Server (NTRS)

1975-01-01

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING CONCRETE ON RUNWAY KSC-375C-10036.32 108-KSC-375C-10036.32, P-21425, ARCHIVE-04501 Aerial oblique of Shuttle Landing Facility. Pouring concrete on runway. Direction North - Altitude 100'.

Stirring-controlled solidified floating solid-liquid drop microextraction as a new solid phase-enhanced liquid-phase microextraction method by exploiting magnetic carbon nanotube-nickel hybrid.

PubMed

Ghazaghi, Mehri; Mousavi, Hassan Zavvar; Shirkhanloo, Hamid; Rashidi, Alimorad

2017-01-25

A specific technique is introduced to overcome limitations of classical solidification of floating organic drop microextraction, such as tedious and time-consuming centrifuge step and using disperser solvent, by facile and efficient participation of solid and liquid phases. In this proposed method of stirring-controlled solidified floating solid-liquid drop microextraction (SC-SF-SLDME), magnetic carbon nanotube-nickel hybrid (MNi-CNT) as a solid part of the extractors are dispersed ultrasonically in sample solution, and the procedure followed by dispersion of liquid phase (1-undecanol) through high-rate stirring and easily recollection of MNi-CNT in organic solvent droplets through hydrophobic force. With the reduction in speed of stirring, one solid-liquid drop is formed on top of the solution. MNi-CNT acts as both extractor and the coalescence helper between organic droplets for a facile recollection. MNi-CNT was prepared by spray pyrolysis of nickel oleate/toluene mixture at 1000 °C. Four tyrosine kinase inhibitors were selected as model analytes and the effecting parameters were investigated. The results confirmed that magnetic nanoadsorbent has an important role in the procedure and complete collection of dispersed solvent is not achieved in the absence of the solid phase. Also, short extraction time exhibited success of the proposed method and effect of dispersed solid/liquid phases. The limits of quantification (LOQs) for imatinib, sunitinib, erlotinib, and nilotinib were determined to be as low as 0.7, 1.7, 0.6, and 1.0 μg L -1 , respectively. The intra-day precisions (RSDs) were lower than 4.5%. Method performance was investigated by determination of mentioned tyrosine kinase inhibitors (TKIs) in human serum and cerebrospinal fluid samples with good recoveries in the range of 93-98%. Copyright © 2016 Elsevier B.V. All rights reserved.

Workshop Report: Fundamental Reactions in Solid Propellant Combustion

DTIC Science & Technology

1979-05-01

combustion conditions. 6. What effect might a pressure-induced phase transition to a polymorph other than 6- HMX have on the pressure slope break during...pure HMX as well. Nevertheless, it is recommended that the high pressure polymorphs of HMX and RDX be determined. It was also felt that there...plateau burning phenomena E. Solid phase, surface, gas phase reactions F. Phase transitions : melting, vaporization, polymorphs G. Flame

Quick connect coupling

NASA Technical Reports Server (NTRS)

Lomax, Curtis (Inventor); Webbon, Bruce (Inventor)

1995-01-01

A cooling apparatus includes a container filled with a quantity of coolant fluid initially cooled to a solid phase, a cooling loop disposed between a heat load and the container, a pump for circulating a quantity of the same type of coolant fluid in a liquid phase through the cooling loop, and a pair of couplings for communicating the liquid phase coolant fluid into the container in a direct interface with the solid phase coolant fluid.

Deuterium and carbon-13 NMR of the solid polymorphism of benzenehexoyl hexa-n-hexanoate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lifshitz, E.; Goldfarb,, D.; Vega, S.

Deuterium and carbon-13 NMR of specifically labeled benzenehexoyl hexa-n-hexanoate in the various solid-state phases are reported. The spectra exhibit dynamic line shapes which change discontinuously at the phase transitions. The results are interpreted in terms of sequential melting of the side chains on going from the low-temperature solid phases IV, III, etc., toward the liquid. In phase IV the molecules are very nearly static, except for fast rotation of the methyl groups about their C/sub 3/ axes. The results in phase III were quantitatively interpreted in terms of a two-site isomerization process involving simultaneous rotation by 95/sup 0/ about C/submore » 1/-C/sub 2/ and transition from gtg to g'g't (or equivalently g'tg' to ggt) for the rest of the chain. The specific rate of this reaction at 0/sup 0/C is approx. 10/sup 5/s/sup -1/. In phase II additional chain isomerization processes set-in which were, however, not analyzed quantitatively. Further motional modes, involving reorientation of whole chains about their C/sup ar/-O bonds, appear on going to phase I. In all solid phases the benzene ring remains static.« less

Silicon Nitride Equation of State

NASA Astrophysics Data System (ADS)

Swaminathan, Pazhayannur; Brown, Robert

2015-06-01

This report presents the development a global, multi-phase equation of state (EOS) for the ceramic silicon nitride (Si3N4) . Structural forms include amorphous silicon nitride normally used as a thin film and three crystalline polymorphs. Crystalline phases include hexagonal α-Si3N4, hexagonalβ-Si3N4, and the cubic spinel c-Si3N4. Decomposition at about 1900 °C results in a liquid silicon phase and gas phase products such as molecular nitrogen, atomic nitrogen, and atomic silicon. The silicon nitride EOS was developed using EOSPro which is a new and extended version of the PANDA II code. Both codes are valuable tools and have been used successfully for a variety of material classes. Both PANDA II and EOSPro can generate a tabular EOS that can be used in conjunction with hydrocodes. The paper describes the development efforts for the component solid phases and presents results obtained using the EOSPro phase transition model to investigate the solid-solid phase transitions in relation to the available shock data. Furthermore, the EOSPro mixture model is used to develop a model for the decomposition products and then combined with the single component solid models to study the global phase diagram. Sponsored by the NASA Goddard Space Flight Center Living With a Star program office.

Iron Silicide Formation by Precipitation in a Silicon Bicrystal

NASA Astrophysics Data System (ADS)

Portier, X.; Ihlal, A.; Rizk, R.

1997-05-01

Segregation and precipitation of iron in a = 25 silicon bicrystal have been carefully investigated by means of high resolution electron microscopy and energy dispersive X-ray analyses, in combination with capacitance and electron beam induced current measurements. After intentional incorporation of iron in the bicrystal by a simple heating procedure, it was shown that a non-equilibrium segregation of iron has occurred after rapid cooling whereas iron precipitates have been produced upon slow cooling. The silicides are formed mainly at the grain boundary area and they were found to belong to the -FeSi cubic or -FeSi2 tetragonal phases. Each precipitate is simply oriented with respect to one of the two grains without any preference between them. The orientation relationships were found in perfect agreement with those observed for the corresponding iron silicides that are epitaxially grown on oriented silicon substrates. Barrier and recombinative effects on the contaminated (1200 °C) and slowly cooled samples have been detected. These effects have been associated with the formation of iron silicides at the grain boundary. La ségrégation ainsi que la précipitation de siliciures de fer au joint de grains = 25 de silicium ont été etudiées en utilisant la dispersion d'énergie des électrons, la microscopie électronique en transmission haute résolution ainsi que des mesures électriques capacitives et des mesures de courants induits par faisceau d'électrons. A la suite d'une contamination volontaire par diffusion thermique du fer au sein du bicristal, nous avons montré qu'une ségrégation hors-équilibre d'atomes de fer est obtenue après un refroidissement rapide alors qu'un refroidissement lent a pour conséquence la formation de siliciures de fer. Ces petits cristaux de siliciures croissent de préférence au niveau du joint de grains et ils ont pour phase, la phase cubique -FeSi ou la phase quadratique α-FeSi2. Chaque précipité est orienté simplement par rapport à l'un ou à l'autre des deux grains et leurs relations d'orientation coincident avec celles observées pour ces mêmes siliciures épitaxiés sur des surfaces de silicium. Les échantillons contaminés (1200 °C) et refroidis lentement présentent des barrières de potentiel et des effets recombinants. Ces activités électriques ont été associées à la présence de siliciures au niveau du joint.

A microstructure-based model for shape distortion during liquid phase sintering

NASA Astrophysics Data System (ADS)

Upadhyaya, Anish

Tight dimensional control is a major concern in consolidation of alloys via liquid phase sintering. This research demonstrates the role of microstructure in controlling the bulk dimensional changes that occur during liquid phase sintering. The dimensional changes were measured using a coordinate measuring machine and also on a real-time basis using in situ video imaging. To quantify compact distortion, a distortion parameter is formulated which takes into consideration the compact distortion in radial as well as axial directions. The microstructural attributes considered in this study are as follows: solid content, dihedral angle, grain size, grain contiguity and connectivity, and solid-solubility. Sintering experiments were conducted with the W-Ni-Cu, W-Ni-Fe, Mo-Ni-Cu, and Fe-Cu systems. The alloy systems and the compositions were selected to give a range of microstructures during liquid phase sintering. The results show that distortion correlates with the measured microstructural attributes. Systems containing a high solid content, high grain coordination number and contiguity, and large dihedral angle have more structural rigidity. The results show that a minimum two-dimensional grain coordination number of 3.0 is necessary for shape preservation. Based on the experimental observations, a model is derived that relates the critical solid content required for maintaining structural rigidity to the dihedral angle. The critical solid content decreases with an increasing dihedral angle. Consequently, W-Cu alloys, which have a dihedral angle of about 95sp°, can be consolidated without gross distortion with as little as 20 vol.% solid. To comprehensively understand the gravitational effects in the evolution of both the microstructure and the macrostructure during liquid phase sintering, W-Ni-Fe alloys with W content varying from 78 to 93 wt.% were sintered in microgravity. Compositions that slump during ground-based sintering also distort when sintered under microgravity. In ground-based sintering, low solid content alloys distort with a typical elephant-foot profile, while in microgravity, the compacts tend to spheroidize. This study shows that microstructural segregation occurs in both ground-based as well as microgravity sintering. In ground-based experiments, because of the density difference between the solid and the liquid phase, the solid content increases from top to the bottom of the sample. In microgravity, the solid content increases from periphery to the center of the samples. A model is derived to show that grain agglomeration and segregation are energetically favored events and will therefore be inherent to the system, even in the absence of gravity. Real time distortion measurement in alloys having appreciable solid-solubility in the liquid phase, such as W-Ni-Fe and Fe-Cu, show that the bulk of distortion occur within the first 5 min of melt formation. Distortion in such systems can be minimized by presaturating the matrix with the solid phase.

EVALUATION OF SOLID PHASE MICROEXTRACTION FOR THE ANALYSIS OF HYDROPHILIC COMPOUNDS

EPA Science Inventory

Two commercially available solid phase microextractions (SPME) fibers, polyacrylate and carboxem/polydimethylsiloxane (PDMS), were evaluated for their ability to extract hydrophilic compounds from drinking water. Conditions, such as desorption time, desorption temperature, sample...

SOLID PROPELLANT COMBUSTION MECHANISM STUDIES.

DTIC Science & Technology

SOLID ROCKET PROPELLANTS, BURNING RATE), LOW PRESSURE, COMBUSTION PRODUCTS, QUENCHING, THERMAL CONDUCTIVITY, KINETIC THEORY, SURFACE PROPERTIES, PHASE STUDIES, SOLIDS, GASES, PYROLYSIS, MATHEMATICAL ANALYSIS.

Efficient Conservative Reformulation Schemes for Lithium Intercalation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Urisanga, PC; Rife, D; De, S

Porous electrode theory coupled with transport and reaction mechanisms is a widely used technique to model Li-ion batteries employing an appropriate discretization or approximation for solid phase diffusion with electrode particles. One of the major difficulties in simulating Li-ion battery models is the need to account for solid phase diffusion in a second radial dimension r, which increases the computation time/cost to a great extent. Various methods that reduce the computational cost have been introduced to treat this phenomenon, but most of them do not guarantee mass conservation. The aim of this paper is to introduce an inherently mass conservingmore » yet computationally efficient method for solid phase diffusion based on Lobatto III A quadrature. This paper also presents coupling of the new solid phase reformulation scheme with a macro-homogeneous porous electrode theory based pseudo 20 model for Li-ion battery. (C) The Author(s) 2015. Published by ECS. All rights reserved.« less

Gravitational Role in Liquid Phase Sintering

NASA Technical Reports Server (NTRS)

Upadhyaya, Anish; Iacocca, Ronald G.; German, Randall M.

1998-01-01

To comprehensively understand the gravitational effects on the evolution of both the microstructure and the macrostructure during liquid phase sintering, W-Ni-Fe alloys with W content varying from 35 to 98 wt.% were sintered in microgravity. Compositions that slump during ground-based sintering also distort when sintered under microgravity. In ground-based sintering, low solid content alloys distort with a typical elephant-foot profile, while in microgravity, the compacts tend to spheroidize. This study shows that microstructural segregation occurs in both ground-based as well as microgravity sintering. In ground-based experiments, because of the density difference between the solid and the liquid phase, the solid content increases from top to the bottom of the sample. In microgravity, the solid content increases from periphery to the center of the samples. This study also shows that the pores during microgravity sintering act as a stable phase and attain anomalous shapes.

On the formation of molecules and solid-state compounds from the AGB to the PN phases

NASA Astrophysics Data System (ADS)

García-Hernández, D. A.; Manchado, A.

2016-07-01

During the asymptoyic giant branch (AGB) phase, different elements are dredge- up to the stellar surface depending on progenitor mass and metallicity. When the mass loss increases at the end of the AGB, a circumstellar dust shell is formed, where different (C-rich or O-rich) molecules and solid-state compounds are formed. These are further processed in the transition phase between AGB stars and planetary nebulae (PNe) to create more complex organic molecules and inorganic solid-state compounds (e.g., polycyclic aromatic hydrocarbons, fullerenes, and graphene precursors in C-rich environments and oxides and crystalline silicates in O-rich ones). We present an observational review of the different molecules and solid-state materials that are formed from the AGB to the PN phases. We focus on the formation routes of complex fullerene (and fullerene-based) molecules as well as on the level of dust processing depending on metallicity.

A quantitative study of factors influencing lamellar eutectic morphology during solidification

NASA Technical Reports Server (NTRS)

Kaukler, W. F. S.

1981-01-01

The factors that influence the shape of the solid-liquid interface of a lamellar binary eutectic alloy are evaluated. Alloys of carbon tetrabromide and hexachloroethane which serve as a transparent analogue of lamellar metallic eutectics are used. The observed interface shapes are analyzed by computer-aided methods. The solid-liquid interfacial free energies of each of the individual phases comprising the eutectic system are measured as a function of composition using a 'grain boundary groove' technique. The solid-liquid interfacial free energy of the two phases are evaluated directly from the eutectic interface. The phase diagram for the system, the heat of fusion as a function of composition, and the density as a function of composition are measured. The shape of the eutectic interface is controlled mainly by the solid-liquid and solid-solid interfacial free energy relationships at the interface and by the temperature gradient present, rather than by interlamellar diffusion in the liquid at the interface, over the range of growth rates studied.

Formation of soft magnetic high entropy amorphous alloys composites containing in situ solid solution phase

NASA Astrophysics Data System (ADS)

Wei, Ran; Sun, Huan; Chen, Chen; Tao, Juan; Li, Fushan

2018-03-01

Fe-Co-Ni-Si-B high entropy amorphous alloys composites (HEAACs), which containing high entropy solid solution phase in amorphous matrix, show good soft magnetic properties and bending ductility even in optimal annealed state, were successfully developed by melt spinning method. The crystallization phase of the HEAACs is solid solution phase with body centered cubic (BCC) structure instead of brittle intermetallic phase. In addition, the BCC phase can transformed into face centered cubic (FCC) phase with temperature rise. Accordingly, Fe-Co-Ni-Si-B high entropy alloys (HEAs) with FCC structure and a small amount of BCC phase was prepared by copper mold casting method. The HEAs exhibit high yield strength (about 1200 MPa) and good plastic strain (about 18%). Meanwhile, soft magnetic characteristics of the HEAs are largely reserved from HEAACs. This work provides a new strategy to overcome the annealing induced brittleness of amorphous alloys and design new advanced materials with excellent comprehensive properties.

Study of the solid-state amorphization of (GaSb){sub 1-x}Ge{sub x} semiconductors by real-time neutron diffraction and electron microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fedotov, V. K., E-mail: fedotov@issp.ac.ru; Ponyatovsky, E. G.

2011-12-15

The spontaneous amorphization of high-pressure quenched phases of the GaSb-Ge system has been studied by neutron diffraction while slowly heating the phases at atmospheric pressure. The sequence of changes in the structural parameters of the initial crystalline phase and the final amorphous phase is established. The behavior of the phases and the correlation in the structural features of the phase transitions and anomalous thermal effects exhibit signs of the inhomogeneous model of solid-state amorphization.

Application of Berry's Phase to the Effective Mass of Bloch Electrons

ERIC Educational Resources Information Center

Rave, M. J.; Kerr, W. C.

2010-01-01

Berry's phase, although well known since 1984, has received little attention among textbook authors of solid state physics. We attempt to address this lack by showing how the presence of the Berry's phase significantly changes a standard concept (effective mass) found in most solid state texts. Specifically, we show that the presence of a non-zero…

Another First at NSLS-II Construction Site

ScienceCinema

None

2017-12-09

Workers at the NSLS-II ring building construction site recently completed the first complicated concrete pour for the approximately 19-ft.-tall walls of the Utility Tunnel. The continuous pour was the first of its kind, as previous pours have been for foo

Solidification Based Grain Refinement in Steels

DTIC Science & Technology

2011-09-27

project (Tasks 7-9). An industrial trial on an investment casting was done using rare earth silicide additions in a furnace prior to pouring (Task 7...an investment casting was done using rare earth silicide additions in a furnace prior to pounng (la.sk 7). Some of the test parts had a finer...poured at the end of a six casting batch. One test tree with no RE addition was poured. Before the second test tree was poured, sufficient RE silicide was

Mapping coexistence lines via free-energy extrapolation: application to order-disorder phase transitions of hard-core mixtures.

PubMed

Escobedo, Fernando A

2014-03-07

In this work, a variant of the Gibbs-Duhem integration (GDI) method is proposed to trace phase coexistence lines that combines some of the advantages of the original GDI methods such as robustness in handling large system sizes, with the ability of histogram-based methods (but without using histograms) to estimate free-energies and hence avoid the need of on-the-fly corrector schemes. This is done by fitting to an appropriate polynomial function not the coexistence curve itself (as in GDI schemes) but the underlying free-energy function of each phase. The availability of a free-energy model allows the post-processing of the simulated data to obtain improved estimates of the coexistence line. The proposed method is used to elucidate the phase behavior for two non-trivial hard-core mixtures: a binary blend of spheres and cubes and a system of size-polydisperse cubes. The relative size of the spheres and cubes in the first mixture is chosen such that the resulting eutectic pressure-composition phase diagram is nearly symmetric in that the maximum solubility of cubes in the sphere-rich solid (∼20%) is comparable to the maximum solubility of spheres in the cube-rich solid. In the polydisperse cube system, the solid-liquid coexistence line is mapped out for an imposed Gaussian activity distribution, which produces near-Gaussian particle-size distributions in each phase. A terminal polydispersity of 11.3% is found, beyond which the cubic solid phase would not be stable, and near which significant size fractionation between the solid and isotropic phases is predicted.

Thermophysical Parameters of Organic PCM Coconut Oil from T-History Method and Its Potential as Thermal Energy Storage in Indonesia

NASA Astrophysics Data System (ADS)

Silalahi, Alfriska O.; Sukmawati, Nissa; Sutjahja, I. M.; Kurnia, D.; Wonorahardjo, S.

2017-07-01

The thermophysical parameters of organic phase change material (PCM) of coconut oil (co_oil) have been studied by analyzing the temperature vs time data during liquid-solid phase transition (solidification process) based on T-history method, adopting the original version and its modified form to extract the values of mean specific heats of the solid and liquid co_oil and the heat of fusion related to phase transition of co_oil. We found that the liquid-solid phase transition occurs rather gradually, which might be due to the fact that co_oil consists of many kinds of fatty acids with the largest amount of lauric acid (about 50%), with relatively small supercooling degree. For this reason, the end of phase transition region become smeared out, although the inflection point in the temperature derivative is clearly observed signifying the drastic temperature variation between the phase transition and solid phase periods. The data have led to the values of mean specific heat of the solid and liquid co_oil that are comparable to the pure lauric acid, while the value for heat of fusion is resemble to those of the DSC result, both from references data. The advantage of co_oil as the potential sensible and latent TES for room-temperature conditioning application in Indonesia is discussed in terms of its rather broad working temperature range due to its mixture composition characteristic.

Phase equilibrium modeling for high temperature metallization on GaAs solar cells

NASA Technical Reports Server (NTRS)

Chung, M. A.; Davison, J. E.; Smith, S. R.

1991-01-01

Recent trends in performance specifications and functional requirements have brought about the need for high temperature metallization technology to be developed for survivable DOD space systems and to enhance solar cell reliability. The temperature constitution phase diagrams of selected binary and ternary systems were reviewed to determine the temperature and type of phase transformation present in the alloy systems. Of paramount interest are the liquid-solid and solid-solid transformations. Data are being utilized to aid in the selection of electrical contact materials to gallium arsenide solar cells. Published data on the phase diagrams for binary systems is readily available. However, information for ternary systems is limited. A computer model is being developed which will enable the phase equilibrium predictions for ternary systems where experimental data is lacking.

Dense Carbon Monoxide to 160 GPa: Stepwise Polymerization to Two-Dimensional Layered Solid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ryu, Young-Jay; Kim, Minseob; Lim, Jinhyuk

Carbon monoxide (CO) is the first molecular system found to transform into a nonmolecular “polymeric” solid above 5.5 GPa, yet been studied beyond 10 GPa. Here, we show a series of pressure-induced phase transformations in CO to 160 GPa: from a molecular solid to a highly colored, low-density polymeric phase I to translucent, high-density phase II to transparent, layered phase III. The properties of these phases are consistent with those expected from recently predicted 1D P2 1/m, 3D I2 12 12 1, and 2D Cmcm structures, respectively. Thus, the present results advocate a stepwise polymerization of CO triple bonds tomore » ultimately a 2D singly bonded layer structure with an enhanced ionic character.« less

Synthesis of solid solutions of perovskites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dambekalne, M.Y.; Antonova, M.K.; Perro, I.T.

The authors carry out thermographic studies, using a derivatograph, in order to understand the nature of the processes taking place during the synthesis of solid solutions of perovskites. Based on the detailed studies on the phase transformations occurring in the charges of the PSN-PMN solid solutions and on the selection of the optimum conditions for carrying out their synthesis, the authors obtained a powder containing a minimum quantity of the undesirable pyrochlore phase and by sintering it using the hot pressing method, they produced single phase ceramic specimens containing the perovskite phase alone with a density close to the theoreticalmore » value and showing zero apparent porosity and water absorption.« less

Solid-solid collapse transition in a two dimensional model molecular system.

PubMed

Singh, Rakesh S; Bagchi, Biman

2013-11-21

Solid-solid collapse transition in open framework structures is ubiquitous in nature. The real difficulty in understanding detailed microscopic aspects of such transitions in molecular systems arises from the interplay between different energy and length scales involved in molecular systems, often mediated through a solvent. In this work we employ Monte-Carlo simulation to study the collapse transition in a model molecular system interacting via both isotropic as well as anisotropic interactions having different length and energy scales. The model we use is known as Mercedes-Benz (MB), which, for a specific set of parameters, sustains two solid phases: honeycomb and oblique. In order to study the temperature induced collapse transition, we start with a metastable honeycomb solid and induce transition by increasing temperature. High density oblique solid so formed has two characteristic length scales corresponding to isotropic and anisotropic parts of interaction potential. Contrary to the common belief and classical nucleation theory, interestingly, we find linear strip-like nucleating clusters having significantly different order and average coordination number than the bulk stable phase. In the early stage of growth, the cluster grows as a linear strip, followed by branched and ring-like strips. The geometry of growing cluster is a consequence of the delicate balance between two types of interactions, which enables the dominance of stabilizing energy over destabilizing surface energy. The nucleus of stable oblique phase is wetted by intermediate order particles, which minimizes the surface free energy. In the case of pressure induced transition at low temperature the collapsed state is a disordered solid. The disordered solid phase has diverse local quasi-stable structures along with oblique-solid like domains.

Solid-solid collapse transition in a two dimensional model molecular system

NASA Astrophysics Data System (ADS)

Singh, Rakesh S.; Bagchi, Biman

2013-11-01

Solid-solid collapse transition in open framework structures is ubiquitous in nature. The real difficulty in understanding detailed microscopic aspects of such transitions in molecular systems arises from the interplay between different energy and length scales involved in molecular systems, often mediated through a solvent. In this work we employ Monte-Carlo simulation to study the collapse transition in a model molecular system interacting via both isotropic as well as anisotropic interactions having different length and energy scales. The model we use is known as Mercedes-Benz (MB), which, for a specific set of parameters, sustains two solid phases: honeycomb and oblique. In order to study the temperature induced collapse transition, we start with a metastable honeycomb solid and induce transition by increasing temperature. High density oblique solid so formed has two characteristic length scales corresponding to isotropic and anisotropic parts of interaction potential. Contrary to the common belief and classical nucleation theory, interestingly, we find linear strip-like nucleating clusters having significantly different order and average coordination number than the bulk stable phase. In the early stage of growth, the cluster grows as a linear strip, followed by branched and ring-like strips. The geometry of growing cluster is a consequence of the delicate balance between two types of interactions, which enables the dominance of stabilizing energy over destabilizing surface energy. The nucleus of stable oblique phase is wetted by intermediate order particles, which minimizes the surface free energy. In the case of pressure induced transition at low temperature the collapsed state is a disordered solid. The disordered solid phase has diverse local quasi-stable structures along with oblique-solid like domains.

Solid H2 in the interstellar medium

NASA Astrophysics Data System (ADS)

Füglistaler, A.; Pfenniger, D.

2018-06-01

Context. Condensation of H2 in the interstellar medium (ISM) has long been seen as a possibility, either by deposition on dust grains or thanks to a phase transition combined with self-gravity. H2 condensation might explain the observed low efficiency of star formation and might help to hide baryons in spiral galaxies. Aims: Our aim is to quantify the solid fraction of H2 in the ISM due to a phase transition including self-gravity for different densities and temperatures in order to use the results in more complex simulations of the ISM as subgrid physics. Methods: We used molecular dynamics simulations of fluids at different temperatures and densities to study the formation of solids. Once the simulations reached a steady state, we calculated the solid mass fraction, energy increase, and timescales. By determining the power laws measured over several orders of magnitude, we extrapolated to lower densities the higher density fluids that can be simulated with current computers. Results: The solid fraction and energy increase of fluids in a phase transition are above 0.1 and do not follow a power law. Fluids out of a phase transition are still forming a small amount of solids due to chance encounters of molecules. The solid mass fraction and energy increase of these fluids are linearly dependent on density and can easily be extrapolated. The timescale is below one second, the condensation can be considered instantaneous. Conclusions: The presence of solid H2 grains has important dynamic implications on the ISM as they may be the building blocks for larger solid bodies when gravity is included. We provide the solid mass fraction, energy increase, and timescales for high density fluids and extrapolation laws for lower densities.

Solid-phase arsenic speciation in aquifer sediments: A micro-X-ray absorption spectroscopy approach for quantifying trace-level speciation

USGS Publications Warehouse

Nicholas, Sarah L.; Erickson, Melinda L.; Woodruff, Laurel G.; Knaeble, Alan R.; Marcus, Matthew A.; Lynch, Joshua K.; Toner, Brandy M.

2017-01-01

e of this research is to identify the solid-phase sources and geochemical mechanisms of release of As in aquifers of the Des Moines Lobe glacial advance. The overarching concept is that conditions present at the aquifer-aquitard interfaces promote a suite of geochemical reactions leading to mineral alteration and release of As to groundwater. A microprobe X-ray absorption spectroscopy (lXAS) approach is developed and applied to rotosonic drill core samples to identify the solid-phase speciation of As in aquifer, aquitard, and aquifer-aquitard interface sediments. This approach addresses the low solid-phase As concentrations, as well as the fine-scale physical and chemical heterogeneity of the sediments. The spectroscopy data are analyzed using novel cosine-distance and correlation-distance hierarchical clustering for Fe 1s and As 1s lXAS datasets. The solid-phase Fe and As speciation is then interpreted using sediment and well-water chemical data to propose solid-phase As reservoirs and release mechanisms. The results confirm that in two of the three locations studied, the glacial sediment forming the aquitard is the source of As to the aquifer sediments. The results are consistent with three different As release mechanisms: (1) desorption from Fe (oxyhydr)oxides, (2) reductive dissolution of Fe (oxyhydr)oxides, and (3) oxidative dissolution of Fe sulfides. The findings confirm that glacial sediments at the interface between aquifer and aquitard are geochemically active zones for As. The diversity of As release mechanisms is consistent with the geographic heterogeneity observed in the distribution of elevated-As wells.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Du Hongliang; Zhou Wancheng; Luo Fa

The (1-x)(K{sub 0.5}Na{sub 0.5})NbO{sub 3}-x(Ba{sub 0.5}Sr{sub 0.5})TiO{sub 3} (KNN-BST) solid solution has been synthesized by conventional solid-state sintering in order to search for the new lead-free relaxor ferroelectrics for high temperature applications. The phase structure, dielectric properties, and relaxor behavior of the (1-x)KNN-xBST solid solution are systematically investigated. The phase structure of the (1-x)KNN-xBST solid solution gradually changes from pure perovskite phase with an orthorhombic symmetry to the tetragonal symmetry, then to the pseudocubic phase, and to the cubic phase with increasing addition of BST. The 0.90KNN-0.10BST solid solution shows a broad dielectric peak with permittivity maximum near 2500 andmore » low dielectric loss (<4%) in the temperature range of 100-250 deg. C. The result indicates that this material may have great potential for a variety of high temperature applications. The diffuse phase transition and the temperature of the maximum dielectric permittivity shifting toward higher temperature with increasing frequency, which are two typical characteristics for relaxor ferroelectrics, are observed in the (1-x)KNN-xBST solid solution. The dielectric relaxor behavior obeys a modified Curie-Weiss law and a Vogel-Fulcher relationship. The relaxor nature is attributed to the appearance of polar nanoregions owing to the formation of randon fields including local electric fields and elastic fields. These results confirm that the KNN-based relaxor ferroelectrics can be regarded as an alternative direction for the development of high temperature lead-free relaxor ferroelectrics.« less

State and solubility of cadmium as related to xenotic inorganic phases generated homogeneously in soils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, W.J.

The state and solubility of cadmium in waste-treated soils was investigated. Three sets of experiments were designed to elucidate solid phase control of soil solution cadmium. First, the soil solution composition of two soils amended with either sludge or metal contaminated mulch was examined to determine the presence of anions capable of precipitating or co-precipitating cadmium. Results indicated that no known pure solid phases of cadmium developed but that high concentrations of phosphate, sulfate and carbonate apparently influenced cadmium solubility. Secondly, three soils were amended with 10 ug of cadmium as cadmium acetate/g of soil. Three different levels of glycerophosphate,more » cysteine and acetate were added to the soils and incubated at constant temperature and water content in order to release phosphate, sulfate and alkalinity under conditions conducive for homogeneous precipitation. Another set of treatments was prepared in the same fashion with an additional amendment of calcium carbonate to raise soil pH's to 7.0. In the presence of sulfate, cadmium solubility increased with no apparent solid phase formation. The addition of calcium carbonate shifted solid phase control to either calcium carbonate or calcium sulfate. The generation of alkalinity by acetate addition produced solid phase calcium carbonate which in turn controlled cadmium solubility through chemisorption of cadmium on calcite surfaces. In the presence of monobasic calcium phosphate, cadmium was interfacially adsorbed. In the presence of dibasic calcium phosphate, however, cadmium was homogeneously precipitated in the host crystal suggesting possible solid solution.« less

Solid-phase synthesis of the nucleopeptide fragment H-Asp-Ser[pAAAGTAAGCC]-Glu-OH from the nucleoprotein of Bacillus subtilis phage phi 29.

PubMed Central

Dreef-Tromp, C M; van der Maarel, J C; van den Elst, H; van der Marel, G A; van Boom, J H

1992-01-01

The naturally occurring DNA-nucleopeptide H-Asp-Ser[5'-pAAAGTAAGCC-3']-Glu-OH was prepared via a solid-phase phosphite triester approach using N-2-(tert-butyldiphenylsilyloxymethyl)benzoyl protected nucleosides. The oligonucleotide was linked via the extremely base-labile oxalyl ester anchor to the solid support. PMID:1508685

Surface Premelting Coupled with Bulk Phase Transitions in Colloidal Crystals

NASA Astrophysics Data System (ADS)

Li, Bo; Wang, Feng; Zhou, Di; Cao, Xin; Peng, Yi; Ni, Ran; Liao, Maijia; Han, Yilong

2015-03-01

Colloids have been used as outstanding model systems for the studies of various phase transitions in bulk, but not at interface yet. Here we obtained equilibrium crystal-vapor interfaces using tunable attractive colloidal spheres and studied the surface premelting at the single-particle level by video microscopy. We found that monolayer crystals exhibit a bulk isostructural solid-solid transition which triggers the surface premelting. The premelting is incomplete due to the interruption of a mechanical-instability-induced bulk melting. By contrast, two- or multilayer crystals do not have the solid-solid transition and the mechanical instability, hence they exhibit complete premelting with divergent surface-liquid thickness. These novel interplays between bulk and surface phase transitions cast new lights for both types of transitions.

Métamatériaux pour la protection sismique

NASA Astrophysics Data System (ADS)

Guenneau, Sébastien; Enoch, Stefan; Colombi, Andrea; Roux, Philippe; Brule, Stéphane

2018-02-01

Les physiciens des ondes élaborent des modèles théoriques et numériques pour un contrôle accru de la lumière dans des matériaux structurés à l'échelle nanométrique et s'en inspirent pour contrôler les ondes mécaniques de Rayleigh dans des sols structurés à l'échelle métrique, avec des trous dans un sol ou des arbres en surface savamment agencés. Un transfert de paradigme s'opère entre les métamatériaux électromagnétiques pour la photonique et les métamatériaux sismiques pour le génie civil.

Phase-field model of vapor-liquid-solid nanowire growth

NASA Astrophysics Data System (ADS)

Wang, Nan; Upmanyu, Moneesh; Karma, Alain

2018-03-01

We present a multiphase-field model to describe quantitatively nanowire growth by the vapor-liquid-solid (VLS) process. The free-energy functional of this model depends on three nonconserved order parameters that distinguish the vapor, liquid, and solid phases and describe the energetic properties of various interfaces, including arbitrary forms of anisotropic γ plots for the solid-vapor and solid-liquid interfaces. The evolution equations for those order parameters describe basic kinetic processes including the rapid (quasi-instantaneous) equilibration of the liquid catalyst to a droplet shape with constant mean curvature, the slow incorporation of growth atoms at the droplet surface, and crystallization within the droplet. The standard constraint that the sum of the phase fields equals unity and the conservation of the number of catalyst atoms, which relates the catalyst volume to the concentration of growth atoms inside the droplet, are handled via separate Lagrange multipliers. An analysis of the model is presented that rigorously maps the phase-field equations to a desired set of sharp-interface equations for the evolution of the phase boundaries under the constraint of force balance at three-phase junctions (triple points) given by the Young-Herring relation that includes torque term related to the anisotropy of the solid-liquid and solid-vapor interface excess free energies. Numerical examples of growth in two dimensions are presented for the simplest case of vanishing crystalline anisotropy and the more realistic case of a solid-liquid γ plot with cusped minima corresponding to two sets of (10 ) and (11 ) facets. The simulations reproduce many of the salient features of nanowire growth observed experimentally, including growth normal to the substrate with tapering of the side walls, transitions between different growth orientations, and crawling growth along the substrate. They also reproduce different observed relationships between the nanowire growth velocity and radius depending on the growth condition. For the basic normal growth mode, the steady-state solid-liquid interface tip shape consists of a main facet intersected by two truncated side facets ending at triple points. The ratio of truncated and main facet lengths are in quantitative agreement with the prediction of sharp-interface theory that is developed here for faceted nanowire growth in two dimensions.

Solid oxygen revisited

NASA Astrophysics Data System (ADS)

Freiman, Yu. A.; Jodl, H. J.; Crespo, Yanier

2018-05-01

The paper provides an up-to-date review of the experimental and theoretical works on solid oxygen published over the past decade. The most important results presented in this review are the following: Detection of magnetic collapse in neutron studies under the delta-epsilon transition. Identification of the lattice structure of the ɛ phase. In this structure the O2 molecules retain their individuality, but there is an additional link leading to the formation of clusters of molecular quartets with the structural formula (O2)4. Discovery of the unique magnetic properties of the delta phase, which hosts three different magnetic structures in the domain of the same crystallographic structure. The extension of the phase diagram to the high-pressure high-temperature region which was previously beyond the reach for experiment; the molecular η and η‧ phases were found and their structures were identified. Behavior of the melting line up to 60 GPa (1750 K). Discovery of a new molecular θ phase in ultrahigh magnetic fields up to over 190 T and the construction of the thermodynamical magnetic-field-temperature H- T phase diagram on the base of the ultrahigh-field magnetization, optical magneto-transmission, and adiabatic magnetocaloric effect measurements. Prediction of the persistence of the molecular state of solid oxygen up to the pressure of 1.9 TPa which is significantly higher than the corresponding limits in solid hydrogen and nitrogen, other generic molecular solids.

Recent developments and future trends in solid phase microextraction techniques towards green analytical chemistry.

PubMed

Spietelun, Agata; Marcinkowski, Łukasz; de la Guardia, Miguel; Namieśnik, Jacek

2013-12-20

Solid phase microextraction find increasing applications in the sample preparation step before chromatographic determination of analytes in samples with a complex composition. These techniques allow for integrating several operations, such as sample collection, extraction, analyte enrichment above the detection limit of a given measuring instrument and the isolation of analytes from sample matrix. In this work the information about novel methodological and instrumental solutions in relation to different variants of solid phase extraction techniques, solid-phase microextraction (SPME), stir bar sorptive extraction (SBSE) and magnetic solid phase extraction (MSPE) is presented, including practical applications of these techniques and a critical discussion about their advantages and disadvantages. The proposed solutions fulfill the requirements resulting from the concept of sustainable development, and specifically from the implementation of green chemistry principles in analytical laboratories. Therefore, particular attention was paid to the description of possible uses of novel, selective stationary phases in extraction techniques, inter alia, polymeric ionic liquids, carbon nanotubes, and silica- and carbon-based sorbents. The methodological solutions, together with properly matched sampling devices for collecting analytes from samples with varying matrix composition, enable us to reduce the number of errors during the sample preparation prior to chromatographic analysis as well as to limit the negative impact of this analytical step on the natural environment and the health of laboratory employees. Copyright © 2013 Elsevier B.V. All rights reserved.

[Determination of patulin in fruits and jam by solid phase extraction-ultra performance liquid chromatography].

PubMed

Lü, Weichao; Shen, Shuchang; Wang, Chao

2017-11-08

With magnesium silicate, silica gel, diatomite and calcium sulfate as raw materials, a new solid phase extraction column was prepared through a series of processes of grinding to ethanol homogenate, drying and packing into polypropylene tube. The sample was hydrolyzed by pectinase, extracted by acetonitrile and purified by solid phase extraction. The target compounds were separated on a C18 column (100 mm×2.1 mm, 1.8 μm), using 0.8% (v/v) tetrahydrofuran solution as mobile phase with a flow rate of 0.5 mL/min. The detection wavelength was 276 nm. The effect of pectinase on extraction yield and purification effect of solid-phase extraction column were investigated. The optimum chromatographic conditions were selected. There was a good linear relationship between the peak heights and the mass concentrations of patulin in the range of 0.1 to 10 mg/L with the correlation coefficient ( R 2 ) of 1. The limit of detection for this method was 10.22 μg/kg. The spiked recoveries of samples were 86.58%-94.84% with the relative standard deviations (RSDs) of 1.45%-2.28%. The results indicated that the self-made solid phase extraction column had a good purification efficiency, and the UPLC had a high separation efficiency. The method is simple, accurate and of great significance for the quality and safety control of fruit products.

Preparation of Ion Exchange Films for Solid-Phase Spectrophotometry and Solid-Phase Fluorometry

NASA Technical Reports Server (NTRS)

Hill, Carol M.; Street, Kenneth W.; Tanner, Stephen P.; Philipp, Warren H.

2000-01-01

Atomic spectroscopy has dominated the field of trace inorganic analysis because of its high sensitivity and selectivity. The advantages gained by the atomic spectroscopies come with the disadvantage of expensive and often complicated instrumentation. Solid-phase spectroscopy, in which the analyte is preconcentrated on a solid medium followed by conventional spectrophotometry or fluorometry, requires less expensive instrumentation and has considerable sensitivity and selectivity. The sensitivity gains come from preconcentration and the use of chromophore (or fluorophore) developers and the selectivity is achieved by use of ion exchange conditions that favor the analyte in combination with speciative chromophores. Little work has been done to optimize the ion exchange medium (IEM) associated with these techniques. In this report we present a method for making ion exchange polymer films, which considerably simplify the solid-phase spectroscopic techniques. The polymer consists of formaldehyde-crosslinked polyvinyl alcohol with polyacrylic acid entrapped therein. The films are a carboxylate weak cation exchanger in the calcium form. They are mechanically sturdy and optically transparent in the ultraviolet and visible portion of the spectrum, which makes them suitable for spectrophotometry and fluorometry.

Disordered porous solids : from chord distributions to small angle scattering

NASA Astrophysics Data System (ADS)

Levitz, P.; Tchoubar, D.

1992-06-01

Disordered biphasic porous solids are examples of complex interfacial media. Small angle scattering strongly depends on the geometrical properties of the internal surface partitioning a porous system. Properties of the second derivative of the bulk autocorrelation function quantitatively defines the level of connection between the small angle scattering and the statistical properties of this interface. A tractable expression of this second derivative, involving the pore and the mass chord distribution functions, was proposed by Mering and Tchoubar (MT). Based on the present possibility to make a quantitative connection between imaging techniques and the small angle scattering, this paper tries to complete and to extend the MT approach. We first discuss how chord distribution functions can be used as fingerprints of the structural disorder. An explicit relation between the small angle scattering and these chord distributions is then proposed. In a third part, the application to different types of disorder is critically discussed and predictions are compared to available experimental data. Using image processing, we will consider three types of disorder : the long-range Debye randomness, the “ correlated " disorder with a special emphasis on the structure of a porous glass (the vycor), and, finally, complex structures where length scale invariance properties can be observed. Les solides poreux biphasiques sont des exemples de milieux interfaciaux complexes. La diffusion aux petits angles (SAS) dépend fortement des propriétés géométriques de l'interface partitionant le milieu poreux. Les propriétés de la dérivée seconde de la fonction d'autocorrélation de densité définit quantitativement le niveau de connection entre la diffusion aux petits angles et les caractéristiques statistiques de cette interface. Une expression utilisable de cette seconde dérivée, impliquant les distributions de cordes associées à la phase massique et au réseau de pores, fut proposée par Mering et Tchoubar (MT). Mettant à profit la possibilité actuelle d'une comparaison quantitative entre les techniques d'imagerie et la diffusion aux petits angles, ce papier tente de compléter et d'étendre l'approche MT. Dans un premier temps, nous montrons en quoi la connaissance de ces distributions de cordes permet de distinguer certains types de désordres structuraux. Une relation explicite entre le spectre de diffusion aux petits angles et les distributions de cordes est alors proposée. Dans une troisième partie, l'application à différents types de désordre est discutée et les prédictions du modèle comparées aux résultats expérimentaux disponibles. Par utilisation du traitement d'images, nous nous intéressons à trois types de désordre : le milieu aléatoire de Debye, pour ses propriétés à grandes distances, le désordre “ corrélé " avec une attention particulière pour le cas d'un verre poreux (le Vycor) et enfin des organisations complexes où des propriétés d'invariance d'échelle de longueur peuvent être observées.

As-Cast Icosashedral Quasicrystals in Ti-Zr-Ni Alloys

NASA Astrophysics Data System (ADS)

Lee, Geun Woo; Gangopadhyay, Anup K.; Kelton, Kenneth F.

2002-03-01

Most Ti-based icosahedral quasicrystals (i-phase) obtained by rapid quenching from the melt are metastable and disordered. In contrast, the Ti-Zr-Ni i-phase prepared by low temperature annealing is stable and better ordered. This i-phase is formed by a solid-state transformation from C14 Laves phase and α (Ti/Zr) solid-solution phase. It has not been possible previously to grow this i-phase directly from the liquid. Here, the nucleation and growth of the i-phase from the liquid in as-cast Ti-Zr-Ni alloys is reported. Pentagonal growth ledges in as-cast Ti-Zr-Ni ingots are clearly observed. Transmission electron microscopy and x-ray diffraction studies confirm the phase identity. Differential scanning calorimetry measurements show an endothermic transformation from the i-phase to a phase mixture of the C14 Laves and solid-solution phases, demonstrating that this i-phase is also stable. The short time that the liquid remains in the Laves phase-forming-field and the higher nucleation rate of the i-phase, owing to the presumed similarity between the local atomic structures of the i-phase and liquid, allows the i-phase to nucleate and grow directly from the liquid. Container-less solidification studies using electrostatic levitation (ESL) techniques support this conclusion.

Phase Behavior Modeling of Asphaltene Precipitation for Heavy Crudes: A Promising Tool Along with Experimental Data

NASA Astrophysics Data System (ADS)

Tavakkoli, M.; Kharrat, R.; Masihi, M.; Ghazanfari, M. H.; Fadaei, S.

2012-12-01

Thermodynamic modeling is known as a promising tool for phase behavior modeling of asphaltene precipitation under different conditions such as pressure depletion and CO2 injection. In this work, a thermodynamic approach is used for modeling the phase behavior of asphaltene precipitation. The precipitated asphaltene phase is represented by an improved solid model, while the oil and gas phases are modeled with an equation of state. The PR-EOS was used to perform flash calculations. Then, the onset point and the amount of precipitated asphaltene were predicted. A computer code based on an improved solid model has been developed and used for predicting asphaltene precipitation data for one of Iranian heavy crudes, under pressure depletion and CO2 injection conditions. A significant improvement has been observed in predicting the asphaltene precipitation data under gas injection conditions. Especially for the maximum value of asphaltene precipitation and for the trend of the curve after the peak point, good agreement was observed. For gas injection conditions, comparison of the thermodynamic micellization model and the improved solid model showed that the thermodynamic micellization model cannot predict the maximum of precipitation as well as the improved solid model. The non-isothermal improved solid model has been used for predicting asphaltene precipitation data under pressure depletion conditions. The pressure depletion tests were done at different levels of temperature and pressure, and the parameters of a non-isothermal model were tuned using three onset pressures at three different temperatures for the considered crude. The results showed that the model is highly sensitive to the amount of solid molar volume along with the interaction coefficient parameter between the asphaltene component and light hydrocarbon components. Using a non-isothermal improved solid model, the asphaltene phase envelope was developed. It has been revealed that at high temperatures, an increase in the temperature results in a lower amount of asphaltene precipitation and also it causes the convergence of lower and upper boundaries of the asphaltene phase envelope. This work illustrates successful application of a non-isothermal improved solid model for developing the asphaltene phase envelope of heavy crude which can be helpful for monitoring and controlling of asphaltene precipitation through the wellbore and surface facilities during heavy oil production.

Préface

NASA Astrophysics Data System (ADS)

Ouerdane, Youcef; Laporte, Pierre

2005-06-01

L'objectif de la série de colloques UVX est de réunir, au rythme d'une fois tous les deux ans, les scientifiques et industriels travaillant dans le domaine du développement des sources de photon de grande énergie (UV, VUV, et X) et de leurs applications. En particulier cette manifestation est l'occasion de faire se rencontrer une communauté très pluridisciplinaire (physique, chimie, biologie, sciences de l'univers) liée à des domaines en forte évolution technologique (lasers et rayonnement synchrotron notamment). Le colloque UVX 2004 s'est tenu au Palais des Congrès de Saint-Étienne (42000) du 7 au 11 juin 2004. La période écoulée depuis l'édition précédente (Oléron 2002) a été particulièrement active dans tous les domaines concernés : grands projets de sources, méthodes de diagnostic au sens large. Une nouvelle fois on constate que le bref et l'ultra-bref ont une place privilégiée, qu'il s'agisse du travail sur les accélérateurs ou sur les lasers qui, bien sûr, dans la course aux temps courts remportent la palme avec la présence de spécialistes du domaine attoseconde. La communauté représentée a la chance d'être en prise directe avec de très grands projets en phase active de réalisation comme le Laser Megajoule (LMJ), la source SOLEIL, et un projet d'ampleur plus modeste mais remarquable dans son domaine : la source LASERIX d'Orsay/Palaiseau. On pourra citer aussi le projet Arc en Ciel qui, lui, est encore au stade de sa définition. - SOLEIL, source de nouvelle génération de rayonnement synchrotron (plateau de Saclay) est dans une phase active de réalisation : achèvement de l'infrastructure en 2005 et injection du 1o faisceau dans l'anneau de stockage prévu également en 2005. Cette source devrait être la meilleure au monde dans le domaine VUV/X mous, tout en restant très polyvalente (brillance, accordabilité, structure temporelle, polarisation) et complémentaire de l'ESRF. Au final on disposera de 21 lignes de lumière sur onduleurs et 22 sur aimants de courbure. Les premiers “utilisateurs” sont prévus au printemps 2006 avec couverture de l'IR jusqu'aux X durs pour des études variées notamment dans le domaine de la matière condensée. - La LIL (ligne d'intégration laser) du LMJ fonctionne avec 4 faisceaux (de 30 kJ à 351 nm) et un ensemble de diagnostics plasma est en cours de validation (énergie, imagerie X, spectrométrie X). Un souci d'ouverture collaborative (France et étranger) est affiché. - LASERIX (LIXAM, LOA) a pour but de doter les scientifiques français d'un laser émettant en “quasi-routine” de l'émission laser X à 6 tirs/mn basée sur différents schémas collisionnels et donc différentes longueurs d'ondes, et mettant en oeuvre un laser saphir-titane ultra bref de 40 J pour la génération plasma. - Le projet Arc en Ciel (CEA, LOA) se penche sur la possibilité de mise en oeuvre d'une source de “4^ogénération”. Ces sources se veulent à la fois brillantes, cohérentes, dans la gamme des 100 femtosecondes, ce qui conduit à tourner le dos aux anneaux de stockage pour se focaliser sur la combinaison accélérateur linéaire/onduleur, complétée par un laser saphir-titane (génération d'harmoniques UV/X dans des gaz). - Une avancée particulièrement intéressante a été récemment réalisée, notamment au LOA, par injection d'un laser X (plasma) par un faisceau X de bonne qualité (polarisation, divergence, temps, contraste...) issu de la génération d'harmoniques élevées par une chaîne saphir-titane femto. - On notera aussi les avancées réalisées dans le domaine des sources incohérentes de forte intensité dans le domaine des X par interaction optimisée de l'interaction laser de puissance-agrégats (GPS-Paris 6 et 7, CEA Saclay), ainsi que par techniques X-pinch à fils à foyer de 10 microns (LPTP-École Polytechnique). - La génération d'harmoniques d'ordres élevés à partir de chaînes laser amplifiées a continué à faire l'objet de très belles études, d'une part par génération dans les gaz et l'obtention bien maîtrisée et caractérisée de rayonnement attoseconde utilisé maintenant pour des mesures effectives de processus électroniques au sein des atomes, et d'autre part par focalisation sur cible solide. Ces derniers travaux (CEA et LOA), par mise en oeuvre du concept de “miroir plasma” qui combat l'ASE, ont permis de monter que la génération d'harmoniques cohérents sur solide était effective. - Dans le domaine des sources UV deux exposés ont présenté l'état de l'art des sources diodes ellesmêmes (LED et Lasers), ainsi que le développement des sources laser ps haute cadence (multikHz/MHz) avec génération d'harmoniques, de puissance moyenne élevée adaptée à de nombreux secteurs applicatifs (traitement des matériaux, biologie, microscopie...). L'aspect “sources”, au sens large était, on le voit, particulièrement représenté avec de belles perspectives pour les années qui viennent. Au delà de ces développements, les sources X ont été utilisées pour des réalisations instrumentales intéressantes dans le domaine de la microscopie X, de la microscopie interférentielle, et de la reconstruction 3D. De tels travaux sont susceptibles de rapides transferts en direction du secteur bio/santé. On notera également l'avancée que représente la réalisation d'un spectromètre à transformée de Fourier pour VUV/XUV (LCFIO/LPPM/SOLEIL). Le domaine du diagnostic, de la mesure, et de la modélisation dans les plasmas est, lui aussi, très actif avec des outils expérimentaux et théoriques très conséquents : modélisation des propriétés spectrales des ions multichargés (CEA-DAM) ; coefficients d'absorption de plasmas lasers (CEA-DSM, LULI, CEA-DAM) ; spectres d'absorption X dans les plasmas femtosecondes incluant des expériences type “pompe-sonde” résolues spatialement et spectralement (LULI, CEA-DAM, CELIA) ; interaction laseratome/molécule en régime UVX ultra-bref (CELIA)... Dans le domaine que l'on peut appeler, au sens large, “travail des matériaux”, on distinguera particulièrement les avancées dans le domaine de la microlithographie “prévues” par road map, avec l'arrivée semble-t-il inéluctable des technologies UVX à 13,5 nm. Les enjeux économiques favorisent des avancées technologiques multiples (optiques multicouches en réflexion, sources...). Par ailleurs l'aptitude des technologies femto pour l'ablation quasi athermique (micro-usinage) et le dépôt de couches minces spécifiques se confirme tout à fait. Enfin, à fluence plus faible, l'outil laser reste un instrument de choix pour l'étude de l'interaction photon-surface : désorption sous illumination laser à excimères à 157 nm et photoémission/photoconductivité du diamant sous éclairement ultra-bref de l'infrarouge à l'UVX. Nous tenons à remercier les membres du comité d'organisation, le comité scientifique et les différents partenaires, institutionnels et industriels, qui par leur soutien ont permis que le colloque UVX puisse se dérouler. Ce colloque a été parrainé par plusieurs départements du CNRS, la Délégation Générale de l'Armement (DGA), le CEA DRECAM, le CEA DAM, le Conseil Général de la Loire, l'Université Jean MONNET de Saint-Étienne, Saint-Étienne Métropole, la ville de Saint-Étienne, Le Pôle Optique Rhône-Alpes, la Société Française d'Optique et le Groupement de Recherche “SAXO” du CNRS. À tous, nous donnons rendez-vous à Caen pour UVX-2006. Youcef OUERDANE Pierre LAPORTE

Des proprietes de l'etat normal du modele de Hubbard bidimensionnel

NASA Astrophysics Data System (ADS)

Lemay, Francois

Depuis leur decouverte, les etudes experimentales ont demontre que les supra-conducteurs a haute temperature ont une phase normale tres etrange. Les proprietes de ces materiaux ne sont pas bien decrites par la theorie du liquide de Fermi. Le modele de Hubbard bidimensionnel, bien qu'il ne soit pas encore resolu, est toujours considere comme un candidat pour expliquer la physique de ces composes. Dans cet ouvrage, nous mettons en evidence plusieurs proprietes electroniques du modele qui sont incompatibles avec l'existence de quasi-particules. Nous montrons notamment que la susceptibilite des electrons libres sur reseau contient des singularites logarithmiques qui influencent de facon determinante les proprietes de la self-energie a basse frequence. Ces singularites sont responsables de la destruction des quasi-particules. En l'absence de fluctuations antiferromagnetiques, elles sont aussi responsables de l'existence d'un petit pseudogap dans le poids spectral au niveau de Fermi. Les proprietes du modele sont egalement etudiees pour une surface de Fermi similaire a celle des supraconducteurs a haute temperature. Un parallele est etabli entre certaines caracteristiques du modele et celles de ces materiaux.

Methodes de caracterisation des proprietes thermomecaniques d'un acier martensitique =

NASA Astrophysics Data System (ADS)

Ausseil, Lucas

Le but de l'etude est de developper des methodes permettant de mesurer les proprietes thermomecaniques d'un acier martensitique lors de chauffe rapide. Ces donnees permettent d'alimenter les modeles d'elements finis existant avec des donnees experimentales. Pour cela, l'acier 4340 est utilise. Cet acier est notamment utilise dans les roues d'engrenage, il a des proprietes mecaniques tres interessantes. Il est possible de modifier ses proprietes grâce a des traitements thermiques. Le simulateur thermomecanique Gleeble 3800 est utilise. Il permet de tester theoriquement toutes les conditions presentes dans les procedes de fabrication. Avec les tests de dilatation realises dans ce projet, les temperatures exactes de changement de phases austenitiques et martensitiques sont obtenues. Des tests de traction ont aussi permis de deduire la limite d'elasticite du materiau dans le domaine austenitique allant de 850 °C a 1100 °C. L'effet des deformations sur la temperature de debut de transformation est montre qualitativement. Une simulation numerique est aussi realisee pour comprendre les phenomenes intervenant pendant les essais.

A multilevel simulation approach to derive the slip boundary condition of the solid phase in two-fluid models

NASA Astrophysics Data System (ADS)

Feng, Zhi-Gang; Michaelides, Efstathios; Mao, Shaolin

2011-11-01

The simulation of particulate flows for industrial applications often requires the use of a two-fluid model (TFM), where the solid particles are considered as a separate continuous phase. One of the underlining uncertainties in the use of aTFM in multiphase computations comes from the boundary condition of the solid phase. The no-slip condition at a solid boundary is not a valid assumption for the solid phase. Instead, several researchers advocate a slip condition as a more appropriate boundary condition. However, the question on the selection of an exact slip length or a slip velocity coefficient is still unanswered. In the present work we propose a multilevel simulation approach to compute the slip length that is applicable to a TFM. We investigate the motion of a number of particles near a vertical solid wall, while the particles are in fluidization using a direct numerical simulation (DNS); the positions and velocities of the particles are being tracked and analyzed at each time step. It is found that the time- and vertical-space averaged values of the particle velocities converge, yielding velocity profiles that can be used to deduce the particle slip length close to a solid wall. This work was supported by a grant from the DOE-NETL (DE-NT0008064) and by a grant from NSF (HRD-0932339).

FOURTH ANNUAL REPORT ON DISTRIBUTION STUDIES BETWEEN MELTS AND SOLID PHASES USING RADIOACTIVE TRACERS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ward, R.; Orr, W.C.; Katz, L.

Cerium(III) ion in a barium chloride flux does not readily exchangs with any of the ions in solid BaZrO/sub 3/ or BaTiO/sub 3/. It reacts to form new solid phases, which are identified, and does not enter the original crystal lattices at an appreciable rate. The strontium was found to exchange at a measurable rate with barium in BaTiO/sub 3/ and with the corresponding ions in alkaline-earth zirconates. Results of a series of equilibrium and rate measurements were interpreted to ahow that the exchange produces an additional solid phase, SrTiO/sub 3/, rather than the mixed phase, or solid solution, thatmore » ndght have been expected. The significance of this observation is discussed. The self-exchange of yttnium ions between a solid compound of yttrium and an alkali chloride flux in which yttrium chloride is dissolved appears in the systems studied to depend primaaily on the solubility of the solid. Exchange is rapid and complete in the case of yttrium oxychlonide, which is soluble to the extent of 0.6%, but is limited to the surface of yttrium chromium oxide, which has no measurable solubility in the flux. The introduction of yttrium ion vacancies in the lattice of yttrium chromium oxide has no detectable effect in promoting exchange. (For preceding period see NYO-3279.) (auth)« less

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2013 CFR

2013-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2014 CFR

2014-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2012 CFR

2012-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

Process for recovering chaotropic anions from an aqueous solution also containing other ions

DOEpatents

Rogers, Robin; Horwitz, E. Philip; Bond, Andrew H.

1999-01-01

A solid/liquid process for the separation and recovery of chaotropic anions from an aqueous solution is disclosed. The solid support comprises separation particles having surface-bonded poly(ethylene glycol) groups, whereas the aqueous solution from which the chaotropic anions are separated contains a poly(ethylene glycol) liquid/liquid biphase-forming amount of a dissolved salt (lyotrope). A solid/liquid phase admixture of separation particles containing bound chaotropic anions in such an aqueous solution is also contemplated, as is a chromatography apparatus containing that solid/liquid phase admixture.

Process for recovering chaotropic anions from an aqueous solution also containing other ions

DOEpatents

Rogers, R.; Horwitz, E.P.; Bond, A.H.

1999-03-30

A solid/liquid process for the separation and recovery of chaotropic anions from an aqueous solution is disclosed. The solid support comprises separation particles having surface-bonded poly(ethylene glycol) groups, whereas the aqueous solution from which the chaotropic anions are separated contains a poly(ethylene glycol) liquid/liquid biphase-forming amount of a dissolved salt (lyotrope). A solid/liquid phase admixture of separation particles containing bound chaotropic anions in such an aqueous solution is also contemplated, as is a chromatography apparatus containing that solid/liquid phase admixture. 19 figs.

Numerical simulation analysis of four-stage mutation of solid-liquid two-phase grinding

NASA Astrophysics Data System (ADS)

Li, Junye; Liu, Yang; Hou, Jikun; Hu, Jinglei; Zhang, Hengfu; Wu, Guiling

2018-03-01

In order to explore the numerical simulation of solid-liquid two-phase abrasive grain polishing and abrupt change tube, in this paper, the fourth order abrupt change tube was selected as the research object, using the fluid mechanics software to simulate,based on the theory of solid-liquid two-phase flow dynamics, study on the mechanism of AFM micromachining a workpiece during polishing.Analysis at different inlet pressures, the dynamic pressure distribution pipe mutant fourth order abrasive flow field, turbulence intensity, discuss the influence of the inlet pressure of different abrasive flow polishing effect.

Fluidics platform and method for sample preparation

DOEpatents

Benner, Henry W.; Dzenitis, John M.

2016-06-21

Provided herein are fluidics platforms and related methods for performing integrated sample collection and solid-phase extraction of a target component of the sample all in one tube. The fluidics platform comprises a pump, particles for solid-phase extraction and a particle-holding means. The method comprises contacting the sample with one or more reagents in a pump, coupling a particle-holding means to the pump and expelling the waste out of the pump while the particle-holding means retains the particles inside the pump. The fluidics platform and methods herein described allow solid-phase extraction without pipetting and centrifugation.

Application of solid phase extraction procedures for rare earth elements determination in environmental samples.

PubMed

Pyrzynska, Krystyna; Kubiak, Anna; Wysocka, Irena

2016-07-01

Determination of rare earth elements in environmental samples requires often pre-concentration and separation step due to a low metal content and high concentration of the interfering matrix components. A solid phase extraction technique with different kind of solid sorbents offers a high enrichment factor, rapid phase separation and the possibility of its combination with various detection techniques used either in on-line or off-line mode. The recent developments in this area published over the last five years are presented and discussed in this paper. Copyright © 2016 Elsevier B.V. All rights reserved.

Solid-Phase Spectrophotometric Analysis of 1-Naphthol Using Silica Functionalized with m-Diazophenylarsonic Acid

NASA Astrophysics Data System (ADS)

Zaitseva, Nataliya; Alekseev, Sergei; Zaitsev, Vladimir; Raks, Viktoria

2016-03-01

The m-aminophenylarsonic acid (m-APAA) was immobilized onto the silica gel surface with covalently grafted quaternary ammonium groups via ion exchange. The diazotization of ion-bonded m-APAA resulted in a new solid-phase spectrophotometric reagent for detection of 1-naphtol in environmental water samples. The procedure of solid-phase spectrophotometric analysis is characterized by 20 μg L-1 limit of detection (LOD) of 1-naphtol, up to 2000 concentration factor, and insensitivity to the presence of natural water components as well as to 30-fold excess of phenol, resorcinol, and catechol.

Microwave-assisted solid phase conversion study of Meldrum's acid to ethylenetetracarboxylic dianhydride (C 6O 6)

NASA Astrophysics Data System (ADS)

Taherpour, Avat (Arman)

2010-01-01

Utilization of microwave irradiation provides an effective method for fast synthesizing of some important compounds. Microwave-assisted solid phase is an especial class in chemical synthesis. By the use of MW-irradiation on chemicals, sometimes interesting results can be seen. The synthesis of the interesting molecule ethylenetetracarboxylic dianhydride (C 6O 6) was attempted with a few different methods. In this study, the microwave-assisted solid phase conversion of Meldrum's acid to ethylenetetracarboxylic dianhydride was reported. This conversion was characterized by FT-IR, GC/MS and NMR spectroscopy results.

Solid-Phase and Microwave-Assisted Syntheses of 2,5-Diketopiperazines: Small Molecules with Great Potential

PubMed Central

O'Neill, J.C.; Blackwell, H. E.

2008-01-01

Diketopiperazines (DKPs) are a well-known class of heterocycles that have recently emerged as a promising biologically active scaffold. Solid-phase organic synthesis has become an important tool in the combinatorial exploration of these privileged structures, expediting the synthesis and, therefore, the discovery of active compounds. To date, certain DKPs have shown potent activities against a range of diseases and biological phenomena, including bacterial infections, various cancers, asthma, infertility, premature labor, and HIV. Recent applications of solid-phase DKP synthesis, with a particular focus on cyclative cleavage and microwave-assisted reactions, are highlighted herein. PMID:18288948

Modeling of Thermal Phase Noise in a Solid Core Photonic Crystal Fiber-Optic Gyroscope

PubMed Central

Song, Ningfang; Ma, Kun; Jin, Jing; Teng, Fei; Cai, Wei

2017-01-01

A theoretical model of the thermal phase noise in a square-wave modulated solid core photonic crystal fiber-optic gyroscope has been established, and then verified by measurements. The results demonstrate a good agreement between theory and experiment. The contribution of the thermal phase noise to the random walk coefficient of the gyroscope is derived. A fiber coil with 2.8 km length is used in the experimental solid core photonic crystal fiber-optic gyroscope, showing a random walk coefficient of 9.25 × 10−5 deg/h. PMID:29072605

Enhanced ionic conductivity with Li 7O 2Br 3 phase in Li 3OBr anti-perovskite solid electrolyte

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Jinlong; Li, Shuai; Zhang, Yi

Cubic anti-perovskites with general formula Li 3OX (X = Cl, Br, I) were recently reported as superionic conductors with the potential for use as solid electrolytes in all-solid-state lithium ion batteries. These electrolytes are nonflammable, low-cost, and suitable for thermoplastic processing. However, the primary obstacle of its practical implementation is the relatively low ionic conductivity at room temperature. In this work, we synthesized a composite material consisting of two anti-perovskite phases, namely, cubic Li 3OBr and layered Li 7O 2Br 3, by solid state reaction routes. The results indicate that with the phase fraction of Li 7O 2Br 3 increasingmore » to 44 wt. %, the ionic conductivity increased by more than one order of magnitude compared with pure phase Li 3OBr. Formation energy calculations revealed the meta-stable nature of Li 7O 2Br 3, which supports the great difficulty in producing phase-pure Li 7O 2Br 3 at ambient pressure. Here, methods of obtaining phase-pure Li 7O 2Br 3 will continue to be explored, including both high pressure and metathesis techniques.« less

Enhanced ionic conductivity with Li 7O 2Br 3 phase in Li 3OBr anti-perovskite solid electrolyte

DOE PAGES

Zhu, Jinlong; Li, Shuai; Zhang, Yi; ...

2016-09-07

Cubic anti-perovskites with general formula Li 3OX (X = Cl, Br, I) were recently reported as superionic conductors with the potential for use as solid electrolytes in all-solid-state lithium ion batteries. These electrolytes are nonflammable, low-cost, and suitable for thermoplastic processing. However, the primary obstacle of its practical implementation is the relatively low ionic conductivity at room temperature. In this work, we synthesized a composite material consisting of two anti-perovskite phases, namely, cubic Li 3OBr and layered Li 7O 2Br 3, by solid state reaction routes. The results indicate that with the phase fraction of Li 7O 2Br 3 increasingmore » to 44 wt. %, the ionic conductivity increased by more than one order of magnitude compared with pure phase Li 3OBr. Formation energy calculations revealed the meta-stable nature of Li 7O 2Br 3, which supports the great difficulty in producing phase-pure Li 7O 2Br 3 at ambient pressure. Here, methods of obtaining phase-pure Li 7O 2Br 3 will continue to be explored, including both high pressure and metathesis techniques.« less

Influence of Calcium on Microbial Reduction of Solid Phase Uranium (VI)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Chongxuan; Jeon, Byong-Hun; Zachara, John M.

2007-06-27

The effect of calcium on microbial reduction of a solid phase U(VI), sodium boltwoodite (NaUO2SiO3OH ∙1.5H2O), was evaluated in a culture of a dissimilatory metal-reducing bacterium (DMRB), Shewanella oneidensis strain MR-1. Batch experiments were performed in a non-growth bicarbonate medium with lactate as electron donor at pH 7 buffered with PIPES. Calcium increased both the rate and extent of Na-boltwoodite dissolution by increasing its solubility through the formation of a ternary aqueous calcium-uranyl-carbonate species. The ternary species, however, decreased the rates of microbial reduction of aqueous U(VI). Laser-induced fluorescence spectroscopy (LIFS) and transmission electron microscopy (TEM) revealed that microbial reductionmore » of solid phase U(VI) is a sequentially coupled process of Na-boltwoodite dissolution, U(VI) aqueous speciation, and microbial reduction of dissolved U(VI) to U(IV) that accumulated on bacterial surfaces/periplasm. The overall rates of microbial reduction of solid phase U(VI) can be described by the coupled rates of dissolution and microbial reduction that were both influenced by calcium. The results demonstrated that dissolved U(VI) concentration during microbial reduction was a complex function of solid phase U(VI) dissolution kinetics, aqueous U(VI) speciation, and microbial activity.« less

Micro versus macro solid phase extraction for monitoring water contaminants: a preliminary study using trihalomethanes.

PubMed

Alexandrou, Lydon D; Spencer, Michelle J S; Morrison, Paul D; Meehan, Barry J; Jones, Oliver A H

2015-04-15

Solid phase extraction is one of the most commonly used pre-concentration and cleanup steps in environmental science. However, traditional methods need electrically powered pumps, can use large volumes of solvent (if multiple samples are run), and require several hours to filter a sample. Additionally, if the cartridge is open to the air volatile compounds may be lost and sample integrity compromised. In contrast, micro cartridge based solid phase extraction can be completed in less than 2 min by hand, uses only microlitres of solvent and provides comparable concentration factors to established methods. It is also an enclosed system so volatile components are not lost. The sample can also be eluted directly into a detector (e.g. a mass spectrometer) if required. However, the technology is new and has not been much used for environmental analysis. In this study we compare traditional (macro) and the new micro solid phase extraction for the analysis of four common volatile trihalomethanes (trichloromethane, bromodichloromethane, dibromochloromethane and tribromomethane). The results demonstrate that micro solid phase extraction is faster and cheaper than traditional methods with similar recovery rates for the target compounds. This method shows potential for further development in a range of applications. Copyright © 2015 Elsevier B.V. All rights reserved.

Microwave assisted solid phase extraction for separation preconcentration sulfamethoxazole in wastewater using tyre based activated carbon as solid phase material prior to spectrophotometric determination

NASA Astrophysics Data System (ADS)

Mogolodi Dimpe, K.; Mpupa, Anele; Nomngongo, Philiswa N.

2018-01-01

This work was chiefly encouraged by the continuous consumption of antibiotics which eventually pose harmful effects on animals and human beings when present in water systems. In this study, the activated carbon (AC) was used as a solid phase material for the removal of sulfamethoxazole (SMX) in wastewater samples. The microwave assisted solid phase extraction (MASPE) as a sample extraction method was employed to better extract SMX in water samples and finally the analysis of SMX was done by the UV-Vis spectrophotometer. The microwave assisted solid phase extraction method was optimized using a two-level fractional factorial design by evaluating parameters such as pH, mass of adsorbent (MA), extraction time (ET), eluent ratio (ER) and microwave power (MP). Under optimized conditions, the limit of detection (LOD) and limit of quantification (LOQ) were 0.5 μg L- 1 and 1.7 μg L- 1, respectively, and intraday and interday precision expressed in terms of relative standard deviation were > 6%.The maximum adsorption capacity was 138 mg g- 1 for SMX and the adsorbent could be reused eight times. Lastly, the MASPE method was applied for the removal of SMX in wastewater samples collected from a domestic wastewater treatment plant (WWTP) and river water.

Efficient removal of recalcitrant deep-ocean dissolved organic matter during hydrothermal circulation

NASA Astrophysics Data System (ADS)

Hawkes, Jeffrey A.; Rossel, Pamela E.; Stubbins, Aron; Butterfield, David; Connelly, Douglas P.; Achterberg, Eric P.; Koschinsky, Andrea; Chavagnac, Valérie; Hansen, Christian T.; Bach, Wolfgang; Dittmar, Thorsten

2015-11-01

Oceanic dissolved organic carbon (DOC) is an important carbon pool, similar in magnitude to atmospheric CO2, but the fate of its oldest forms is not well understood. Hot hydrothermal circulation may facilitate the degradation of otherwise un-reactive dissolved organic matter, playing an important role in the long-term global carbon cycle. The oldest, most recalcitrant forms of DOC, which make up most of oceanic DOC, can be recovered by solid-phase extraction. Here we present measurements of solid-phase extractable DOC from samples collected between 2009 and 2013 at seven vent sites in the Atlantic, Pacific and Southern oceans, along with magnesium concentrations, a conservative tracer of water circulation through hydrothermal systems. We find that magnesium and solid-phase extractable DOC concentrations are correlated, suggesting that solid-phase extractable DOC is almost entirely lost from solution through mineralization or deposition during circulation through hydrothermal vents with fluid temperatures of 212-401 °C. In laboratory experiments, where we heated samples to 380 °C for four days, we found a similar removal efficiency. We conclude that thermal degradation alone can account for the loss of solid-phase extractable DOC in natural hydrothermal systems, and that its maximum lifetime is constrained by the timescale of hydrothermal cycling, at about 40 million years.

Multiplexed Colorimetric Solid-Phase Extraction

NASA Technical Reports Server (NTRS)

Gazda, Daniel B.; Fritz, James S.; Porter, Marc D.

2009-01-01

Multiplexed colorimetric solid-phase extraction (MC-SPE) is an extension of colorimetric solid-phase extraction (C-SPE) an analytical platform that combines colorimetric reagents, solid phase extraction, and diffuse reflectance spectroscopy to quantify trace analytes in water. In CSPE, analytes are extracted and complexed on the surface of an extraction membrane impregnated with a colorimetric reagent. The analytes are then quantified directly on the membrane surface using a handheld diffuse reflectance spectrophotometer. Importantly, the use of solid-phase extraction membranes as the matrix for impregnation of the colorimetric reagents creates a concentration factor that enables the detection of low concentrations of analytes in small sample volumes. In extending C-SPE to a multiplexed format, a filter holder that incorporates discrete analysis channels and a jig that facilitates the concurrent operation of multiple sample syringes have been designed, enabling the simultaneous determination of multiple analytes. Separate, single analyte membranes, placed in a readout cartridge create unique, analyte-specific addresses at the exit of each channel. Following sample exposure, the diffuse reflectance spectrum of each address is collected serially and the Kubelka-Munk function is used to quantify each water quality parameter via calibration curves. In a demonstration, MC-SPE was used to measure the pH of a sample and quantitate Ag(I) and Ni(II).

COMPUTATIONAL MODELING OF CIRCULATING FLUIDIZED BED REACTORS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ibrahim, Essam A

2013-01-09

Details of numerical simulations of two-phase gas-solid turbulent flow in the riser section of Circulating Fluidized Bed Reactor (CFBR) using Computational Fluid Dynamics (CFD) technique are reported. Two CFBR riser configurations are considered and modeled. Each of these two riser models consist of inlet, exit, connecting elbows and a main pipe. Both riser configurations are cylindrical and have the same diameter but differ in their inlet lengths and main pipe height to enable investigation of riser geometrical scaling effects. In addition, two types of solid particles are exploited in the solid phase of the two-phase gas-solid riser flow simulations tomore » study the influence of solid loading ratio on flow patterns. The gaseous phase in the two-phase flow is represented by standard atmospheric air. The CFD-based FLUENT software is employed to obtain steady state and transient solutions for flow modulations in the riser. The physical dimensions, types and numbers of computation meshes, and solution methodology utilized in the present work are stated. Flow parameters, such as static and dynamic pressure, species velocity, and volume fractions are monitored and analyzed. The differences in the computational results between the two models, under steady and transient conditions, are compared, contrasted, and discussed.« less

Behaviour of emerging contaminants in sewage sludge after anaerobic digestion.

PubMed

Boix, C; Ibáñez, M; Fabregat-Safont, D; Morales, E; Pastor, L; Sancho, J V; Sánchez-Ramírez, J E; Hernández, F

2016-11-01

Nowadays, there is an increasing concern over the presence of contaminants in the aquatic environment, where they can be introduced from wastewater after their incomplete removal in the treatment plants. In this work, degradation of selected emerging pollutants in the aqueous and solid phases of sewage sludge has been investigated after anaerobic digestion using two different digesters: mesophilic and thermophilic. Initially, sludge samples were screened by ultra-high-performance liquid chromatography coupled to quadrupole time-of-flight mass spectrometry (UHPLC-QTOF MS) for identification of emerging contaminants in the samples. In a second step, a target quantitative method based on LC coupled to tandem MS was applied for selected pollutants identified in the previous screening. The behaviour of the compounds under anaerobic conditions was studied estimating the degradation efficiency and distribution of compounds between both sludge phases. Irbesartan and benzoylecgonine seemed to be notably degraded in both phases of the sludge. Venlafaxine showed a significant concentration decrease in the aqueous phase in parallel to an increase in the solid phase. The majority of the compounds showed an increase of their concentrations in both phases after the digestion. Concentrations in the solid phase were commonly higher than in the aqueous for most contaminants, indicating that they were preferentially adsorbed onto the solid particles. Copyright © 2016 Elsevier Ltd. All rights reserved.

A study of room-temperature LixMn1.5Ni0.5O4 solid solutions

PubMed Central

Saravanan, Kuppan; Jarry, Angelique; Kostecki, Robert; Chen, Guoying

2015-01-01

Understanding the kinetic implication of solid-solution vs. biphasic reaction pathways is critical for the development of advanced intercalation electrode materials. Yet this has been a long-standing challenge in materials science due to the elusive metastable nature of solid solution phases. The present study reports the synthesis, isolation, and characterization of room-temperature LixMn1.5Ni0.5O4 solid solutions. In situ XRD studies performed on pristine and chemically-delithiated, micron-sized single crystals reveal the thermal behavior of LixMn1.5Ni0.5O4 (0 ≤ x ≤ 1) cathode material consisting of three cubic phases: LiMn1.5Ni0.5O4 (Phase I), Li0.5Mn1.5Ni0.5O4 (Phase II) and Mn1.5Ni0.5O4 (Phase III). A phase diagram capturing the structural changes as functions of both temperature and Li content was established. The work not only demonstrates the possibility of synthesizing alternative electrode materials that are metastable in nature, but also enables in-depth evaluation on the physical, electrochemical and kinetic properties of transient intermediate phases and their role in battery electrode performance. PMID:25619504

A study of room-temperature Li xMn 1.5Ni 0.5O 4 solid solutions

DOE PAGES

Saravanan, Kuppan; Jarry, Angelique; Kostecki, Robert; ...

2015-01-26

Understanding the kinetic implication of solid-solution vs. biphasic reaction pathways is critical for the development of advanced intercalation electrode materials. Yet this has been a long-standing challenge in materials science due to the elusive metastable nature of solid solution phases. The present study reports the synthesis, isolation, and characterization of room-temperature Li xMn 1.5Ni 0.5O 4 solid solutions. In situ XRD studies performed on pristine and chemically-delithiated, micron-sized single crystals reveal the thermal behavior of Li xMn 1.5Ni 0.5O 4 (0 ≤ x ≤ 1) cathode material consisting of three cubic phases: LiMn 1.5Ni 0.5O 4 (Phase I), Li 0.5Mnmore » 1.5Ni 0.5O 4 (Phase II) and Mn 1.5Ni 0.5O 4 (Phase III). A phase diagram capturing the structural changes as functions of both temperature and Li content was established. In conclusion, the work not only demonstrates the possibility of synthesizing alternative electrode materials that are metastable in nature, but also enables in-depth evaluation on the physical, electrochemical and kinetic properties of transient intermediate phases and their role in battery electrode performance.« less

Pollutant removal from oily wastewater discharged from car washes through sedimentation-coagulation.

PubMed

Rubí, H; Fall, C; Ortega, R E

2009-01-01

Wastewater from car washes represents a potential problem for the sewer system due to its emulsified oils and suspended material. Treatment of wastewater discharged from four car washes was investigated by sedimentation and coagulation. The effect of the coagulants Servical P (aluminium hydroxychloride), Servican 50 (poly(diallyldimethylammonium chloride)), aluminium sulfate and ferric chloride was evaluated. The achieved removal using sedimentation was of 82%, 88% 73% and 51% for oils, total suspended solids, COD, and turbidity, respectively. In the treatment by coagulation we achieved average efficiencies nearly to 74% for COD removal, greater than 88% in the case of total suspended solids removal and 92% in the case of turbidity and except the performance of Servican 50 greater than 90% in oil removal. We concluded that the oil residual concentration and COD in the treated water allows pouring it in the sewer system complying with the limits of the Mexican rule NOM-002-ECOL-1996 and it is possible even its reuse, at least in the case of the chassis washing of cars.

Lasers solides pompés par diode émettant des impulsions picosecondes à haute cadence dans l'ultraviolet

NASA Astrophysics Data System (ADS)

Balembois, F.; Forget, S.; Papadopoulos, D.; Druon, F.; Georges, P.; Devilder, P.-J.; Lefort, L.

2005-06-01

De nombreuses applications requièrent des sources lasers impulsionnelles ultraviolettes, présentant des durées d'impulsion et des cadences spécifiques. Grâce à l'utilisation de structures d'oscillateurs et d'amplificateurs originales il est possible de réaliser de telles sources à partir de lasers solides pompés par diodes et de profiter ainsi de la compacité, de l'efficacité et de la robustesse de ces sources. Nous présentons ici la réalisation d'un laser à verrouillage de modes et d'un microlaser déclenché permettant d'obtenir des impulsions ultraviolettes picosecondes à une cadence de quelques MHz en vue d'application à la microscopie de fluorescence résolue en temps, ainsi que la mise en œuvre pour le traitement des matériaux d'un système oscillateur-amplificateur produisant plus de 600 mW de rayonnement UV à 266 ou 355 nm avec des impulsions sub-nanosecondes.

Levitation of water and organic substances in high static magnetic fields

NASA Astrophysics Data System (ADS)

Beaugnon, E.; Tournier, R.

1991-08-01

The levitation of various diamagnetic liquid and solid substances such as water, ethanol, acetone, bismuth, antimony, graphite, wood and plastic has been achieved at room temperature in a strong inhomogeneous static magnetic field. These experiments were performed in the hybrid magnet at the Service National des Champs Intenses (CNRS, Grenoble). These findings show that high field superconducting magnets could be used to provide a contactless, low gravity environment for the elaboration of a wide range of materials. En utilisant les forts champs magnétiques produits par la bobine hybride du Service National des Champs Intenses (CNRS, Grenoble), nous avons obtenu àtempérature ambiante la lévitation de substances diamagnétiques solides ou liquides telles que l'eau, l'alcool, l'acétone, le bismuth, l'antimoine, le graphite, le bois et le plastique. Ces résultats montrent que les bobines supraconductrices peuvent être utilisées pour l'élaboration de nombreux matériaux en gravité réduite, sans contact avec un contenant.

Metal Alloy Compositions And Process Background Of The Invention

DOEpatents

Flemings, Merton C.; Martinez-Ayers, Raul A.; de Figueredo, Anacleto M.; Yurko, James A.

2003-11-11

A skinless metal alloy composition free of entrapped gas and comprising primary solid discrete degenerate dendrites homogeneously dispersed within a secondary phase is formed by a process wherein the metal alloy is heated in a vessel to render it a liquid. The liquid is then rapidly cooled while vigorously agitating it under conditions to avoid entrapment of gas while forming solid nuclei homogeneously distributed in the liquid. Agitation then is ceased when the liquid contains a small fraction solid or the liquid-solid alloy is removed from the source of agitation while cooling is continued to form the primary solid discrete degenerate dendrites in liquid secondary phase. The solid-liquid mixture then can be formed such as by casting.

Fluorous tagging strategy for solution-phase synthesis of small molecules, peptides and oligosaccharides

PubMed Central

Zhang, Wei

2005-01-01

The purification of reaction mixtures is a slow process in organic synthesis, especially during the production of large numbers of analogs and compound libraries. Phase-tag methods such as solid-phase synthesis and fluorous synthesis, provide efficient ways of addressing the separation issue. Fluorous synthesis employs functionalized perfluoroalkyl groups attached to substrates or reagents. The separation of the resulting fluorous molecules can be achieved using strong and selective fluorous liquid-liquid extraction, fluorous silica gel-based solid-phase extraction or high-performance liquid chromatography. Fluorous technology is a novel solution-phase method, which has the advantages of fast reaction times in homogeneous environments, being readily adaptable to literature conditions, having easy intermediate analysis, and having flexibility in reaction scale and scope. In principle, any synthetic methods that use a solid-support could be conducted in solution-phase by replacing the polymer linker with a corresponding fluorous tag. This review summarizes the progress of fluorous tags in solution-phase synthesis of small molecules, peptides and oligosaccharides. PMID:15595439

Thermodynamic, crystallographic, and dielectric study of the nature of glass transitions in cyclo-octanol

NASA Astrophysics Data System (ADS)

Puertas, Ricardo; Rute, Maria A.; Salud, Josep; López, David O.; Diez, Sergio; van Miltenburg, J. Kees; Pardo, Luis C.; Tamarit, Josep Ll.; Barrio, Maria; Pérez-Jubindo, Miguel A.; de La Fuente, Maria R.

2004-06-01

The stable solid polymorphism of cyclooctanol (C8H16O, for short C8 OH) is revealed to be a complex problem and only two stable solid phases, denoted on cooling from the liquid as phases I and II, are found using static (thermodynamic and x-ray diffraction) as well as dynamic (dielectric spectroscopy) experimental techniques. Both solid phases are known to exhibit glass transitions if they are cooled down fast enough to prevent transition to ordered crystalline states. Although glass transitions corresponding to both phases had been well documented by means of specific heat measurements, x-ray measurements constitute, as far as we know, the first evidence from the structural point of view. In addition, a great amount of dielectric works devoted to phase I and its glass transition, were published in the past but next to nothing relating to the dielectric properties of phase II and its glass transition. The nature of the disorder of phase II will be discussed.

Refractive Surgery: New Techniques and Usability for Military Personnel (La chirurgie refractive: Nouvelles techniques et leur application pour le personnel militaire)

DTIC Science & Technology

2012-11-01

de loin sans correction, la chirurgie réfractive permet aux jeunes recrues ou militaires du rang de satisfaire aux normes de vision sans...correction exigées pour le métier militaire de leur choix, d’où une augmentation du nombre de candidats et la possibilité pour les individus...réfractive risquent d’engendrer des handicaps visuels et d’écourter des carrières militaires. Pour cette raison, la qualité du service fourni

The effects of glass doping, temperature and time on the morphology, composition, and iron redox of spinel crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matyas, Josef; Amonette, James E.; Kukkadapu, Ravi K.

2014-10-31

Precipitation of large crystals/agglomerates of spinel and their accumulation in the pour spout riser of a Joule-heated ceramic melter during idling can plug the melter and prevent pouring of molten glass into canisters. Thus, there is a need to understand the effects of spinel-forming components, temperature, and time on the growth of crystals in connection with an accumulation rate. In our study, crystals of spinel [Fe, Ni, Mn, Zn, Sn][Fe, Cr]₂O₄ were precipitated from simulated high-level waste borosilicate glasses containing different concentrations of Ni, Fe, and Cr by heat treating at 850 and 900°C for different times. These crystals weremore » extracted from the glasses and analyzed with scanning electron microscopy and image analysis for size and shape, with inductively coupled plasma-atomic emission spectroscopy and atom probe tomography for concentration of spinel-forming components, and with wet colorimetry and Mössbauer spectroscopy for Fe²⁺/Fe total ratio. High concentrations of Ni, Fe, and Cr in glasses resulted in the precipitation of crystals larger than 100 µm in just two days. Crystals were a solid solution of NiFe₂O₄, NiCr₂O₄, and -Fe₂O₃ (identified only in the high-Ni-Fe glass) and also contained small concentrations of less than 1 at% of Li, Mg, Mn, and Al.« less

Que peut-on voir avec des neutrons? Une introduction pour des non spécialistes

NASA Astrophysics Data System (ADS)

Schweizer, J.

2005-11-01

Le neutron est une particule élémentaire qui a été découverte en 1932 par James Chadwick. Ses caractéristiques principales sont résumées dans le tableau I. Il a été utilisé pour la première fois par Clifford Shull en 1946 comme outil pour des expériences de diffusion. Cette technique s'est depuis constamment développée pour concerner tous les aspects de la matière condensée: physique, chimie, matériaux, biologie. Il s'agit d'un outil tout à fait exceptionnel car le neutron possède des propriétés uniques et particulièrement adaptées pour ces études.

Effects of a reactive barrier and aquifer geology on metal distribution and mobility in a mine drainage impacted aquifer.

PubMed

Doerr, Nora A; Ptacek, Carol J; Blowes, David W

2005-06-01

The Nickel Rim aquifer has been impacted for five decades by a metal-rich plume generated from the Nickel Rim mine tailings impoundment. Metals released by the oxidation of pyrrhotite in the unsaturated zone of the tailings migrate into the downgradient aquifer, affecting both the groundwater and the aquifer solids. A reactive barrier has been installed in the aquifer to remove sulfate and metals from the groundwater. The effect of the reactive barrier on metal concentrations in the aquifer solids has not previously been studied. In this study, a series of selective extraction procedures was applied to cores of aquifer sediment, to ascertain the distribution of metals among various solid phases present in the aquifer. Extraction results were combined with groundwater chemistry, geochemical modelling and solid-phase microanalyses, to assess the potential mobility of metals under changing geochemical conditions. Reactions within the reactive barrier caused an increase in the solid-phase carbonate content downgradient from the barrier. The concentrations of poorly crystalline, oxidized phases of Mn and Fe, as well as concentrations of Cr(III) associated with oxidized Fe, and poorly crystalline Zn, are lower downgradient from the barrier, whereas total solid-phase metal concentrations remain constant. Iron and Mn accumulate as oxidized, easily extractable forms in a peat layer overlying the aquifer. Although these oxides may buffer reducing plumes, they also have the potential to release metals to the groundwater, should a reduced condition be imposed on the aquifer by remedial actions.

Silica Modified with Polyaniline as a Potential Sorbent for Matrix Solid Phase Dispersion (MSPD) and Dispersive Solid Phase Extraction (d-SPE) of Plant Samples

PubMed Central

Sowa, Ireneusz; Wójciak-Kosior, Magdalena; Strzemski, Maciej; Sawicki, Jan; Staniak, Michał; Dresler, Sławomir; Szwerc, Wojciech; Mołdoch, Jarosław; Latalski, Michał

2018-01-01

Polyaniline (PANI) is one of the best known conductive polymers with multiple applications. Recently, it was also used in separation techniques, mostly as a component of composites for solid-phase microextraction (SPME). In the present paper, sorbent obtained by in situ polymerization of aniline directly on silica gel particles (Si-PANI) was used for dispersive solid phase extraction (d-SPE) and matrix solid–phase extraction (MSPD). The efficiency of both techniques was evaluated with the use of high performance liquid chromatography with diode array detection (HPLC-DAD) quantitative analysis. The quality of the sorbent was verified by Raman spectroscopy and microscopy combined with automated procedure using computer image analysis. For extraction experiments, triterpenes were chosen as model compounds. The optimal conditions were as follows: protonated Si-PANI impregnated with water, 160/1 sorbent/analyte ratio, 3 min of extraction time, 4 min of desorption time and methanolic solution of ammonia for elution of analytes. The proposed procedure was successfully used for pretreatment of plant samples. PMID:29565297

Kerr-AdS analogue of triple point and solid/liquid/gas phase transition

NASA Astrophysics Data System (ADS)

Altamirano, Natacha; Kubizňák, David; Mann, Robert B.; Sherkatghanad, Zeinab

2014-02-01

We study the thermodynamic behavior of multi-spinning d = 6 Kerr-anti de Sitter black holes in the canonical ensemble of fixed angular momenta J1 and J2. We find, dependent on the ratio q = J2/J1, qualitatively different interesting phenomena known from the ‘every day thermodynamics’ of simple substances. For q = 0 the system exhibits recently observed reentrant large/small/large black hole phase transitions, but for 0 < q ≪ 1 we find an analogue of a ‘solid/liquid’ phase transition. Furthermore, for q ∈ (0.00905, 0.0985) the system displays the presence of a large/intermediate/small black hole phase transition with two critical and one triple (or tricritical) points. This behavior is reminiscent of the solid/liquid/gas phase transition except that the coexistence line of small and intermediate black holes does not continue for an arbitrary value of pressure (similar to the solid/liquid coexistence line) but rather terminates at one of the critical points. Finally, for q > 0.0985 we observe the ‘standard liquid/gas behavior’ of the Van der Waals fluid.

New Density Functional Approach for Solid-Liquid-Vapor Transitions in Pure Materials

NASA Astrophysics Data System (ADS)

Kocher, Gabriel; Provatas, Nikolas

2015-04-01

A new phase field crystal (PFC) type theory is presented, which accounts for the full spectrum of solid-liquid-vapor phase transitions within the framework of a single density order parameter. Its equilibrium properties show the most quantitative features to date in PFC modeling of pure substances, and full consistency with thermodynamics in pressure-volume-temperature space is demonstrated. A method to control either the volume or the pressure of the system is also introduced. Nonequilibrium simulations show that 2- and 3-phase growth of solid, vapor, and liquid can be achieved, while our formalism also allows for a full range of pressure-induced transformations. This model opens up a new window for the study of pressure driven interactions of condensed phases with vapor, an experimentally relevant paradigm previously missing from phase field crystal theories.

Solid-solid phase transformation via internal stress-induced virtual melting, significantly below the melting temperature. Application to HMX energetic crystal.

PubMed

Levitas, Valery I; Henson, Bryan F; Smilowitz, Laura B; Asay, Blaine W

2006-05-25

We theoretically predict a new phenomenon, namely, that a solid-solid phase transformation (PT) with a large transformation strain can occur via internal stress-induced virtual melting along the interface at temperatures significantly (more than 100 K) below the melting temperature. We show that the energy of elastic stresses, induced by transformation strain, increases the driving force for melting and reduces the melting temperature. Immediately after melting, stresses relax and the unstable melt solidifies. Fast solidification in a thin layer leads to nanoscale cracking which does not affect the thermodynamics or kinetics of the solid-solid transformation. Thus, virtual melting represents a new mechanism of solid-solid PT, stress relaxation, and loss of coherence at a moving solid-solid interface. It also removes the athermal interface friction and deletes the thermomechanical memory of preceding cycles of the direct-reverse transformation. It is also found that nonhydrostatic compressive internal stresses promote melting in contrast to hydrostatic pressure. Sixteen theoretical predictions are in qualitative and quantitative agreement with experiments conducted on the PTs in the energetic crystal HMX. In particular, (a) the energy of internal stresses is sufficient to reduce the melting temperature from 551 to 430 K for the delta phase during the beta --> delta PT and from 520 to 400 K for the beta phase during the delta --> beta PT; (b) predicted activation energies for direct and reverse PTs coincide with corresponding melting energies of the beta and delta phases and with the experimental values; (c) the temperature dependence of the rate constant is determined by the heat of fusion, for both direct and reverse PTs; results b and c are obtained both for overall kinetics and for interface propagation; (d) considerable nanocracking, homogeneously distributed in the transformed material, accompanies the PT, as predicted by theory; (e) the nanocracking does not change the PT thermodynamics or kinetics appreciably for the first and the second PT beta <--> delta cycles, as predicted by theory; (f) beta <--> delta PTs start at a very small driving force (in contrast to all known solid-solid transformations with large transformation strain), that is, elastic energy and athermal interface friction must be negligible; (g) beta --> alpha and alpha --> beta PTs, which are thermodynamically possible in the temperature range 382.4 < theta < 430 K and below 382.4 K, respectively, do not occur.

Finite-deformation phase-field chemomechanics for multiphase, multicomponent solids

NASA Astrophysics Data System (ADS)

Svendsen, Bob; Shanthraj, Pratheek; Raabe, Dierk

2018-03-01

The purpose of this work is the development of a framework for the formulation of geometrically non-linear inelastic chemomechanical models for a mixture of multiple chemical components diffusing among multiple transforming solid phases. The focus here is on general model formulation. No specific model or application is pursued in this work. To this end, basic balance and constitutive relations from non-equilibrium thermodynamics and continuum mixture theory are combined with a phase-field-based description of multicomponent solid phases and their interfaces. Solid phase modeling is based in particular on a chemomechanical free energy and stress relaxation via the evolution of phase-specific concentration fields, order-parameter fields (e.g., related to chemical ordering, structural ordering, or defects), and local internal variables. At the mixture level, differences or contrasts in phase composition and phase local deformation in phase interface regions are treated as mixture internal variables. In this context, various phase interface models are considered. In the equilibrium limit, phase contrasts in composition and local deformation in the phase interface region are determined via bulk energy minimization. On the chemical side, the equilibrium limit of the current model formulation reduces to a multicomponent, multiphase, generalization of existing two-phase binary alloy interface equilibrium conditions (e.g., KKS). On the mechanical side, the equilibrium limit of one interface model considered represents a multiphase generalization of Reuss-Sachs conditions from mechanical homogenization theory. Analogously, other interface models considered represent generalizations of interface equilibrium conditions consistent with laminate and sharp-interface theory. In the last part of the work, selected existing models are formulated within the current framework as special cases and discussed in detail.

Introduction to investigations of the negative corona and EHD flow in gaseous two-phase fluids

NASA Astrophysics Data System (ADS)

Jerzy, MIZERACZYK; Artur, BERENDT

2018-05-01

Research interests have recently been directed towards electrical discharges in multi-phase environments. Natural electrical discharges, such as lightning and coronas, occur in the Earth’s atmosphere, which is actually a mixture of gaseous phase (air) and suspended solid and liquid particulate matters (PMs). An example of an anthropogenic gaseous multi-phase environment is the flow of flue gas through electrostatic precipitators (ESPs), which are generally regarded as a mixture of a post-combustion gas with solid PM and microdroplets suspended in it. Electrical discharges in multi-phase environments, the knowledge of which is scarce, are becoming an attractive research subject, offering a wide variety of possible discharges and multi-phase environments to be studied. This paper is an introduction to electrical discharges in multi-phase environments. It is focused on DC negative coronas and accompanying electrohydrodynamic (EHD) flows in a gaseous two-phase fluid formed by air (a gaseous phase) and solid PM (a solid phase), run under laboratory conditions. The introduction is based on a review of the relevant literature. Two cases will be considered: the first case is of a gaseous two-phase fluid, initially motionless in a closed chamber before being subjected to a negative corona (with the needle-to-plate electrode arrangement), which afterwards induces an EHD flow in the chamber, and the second, of a gaseous two-phase fluid flowing transversely with respect to the needle-to-plate electrode axis along a chamber with a corona discharge running between the electrodes. This review-based introductory paper should be of interest to theoretical researchers and modellers in the field of negative corona discharges in single- or two-phase fluids, and for engineers who work on designing EHD devices (such as ESPs, EHD pumps, and smoke detectors).

Etude analytique du fonctionnement des moteurs à réluctance alimentés à fréquence variable

NASA Astrophysics Data System (ADS)

Sargos, F. M.; Gudefin, E. J.; Zaskalicky, P.

1995-03-01

In switched reluctance motors fed by a constant voltage source (like a battery) at high frequencies, the current becomes unpredictable and often cannot reach a given reference value, because of the variation of the inductances with the rotor position ; the “motional” m.m.f. generates commutation troubles which increase with the frequency. An optimal control as well as an approximate design of the motor require a quick and simple calculation of currents, powers and losses ; now, in principle, the non-linear electrical equation needs a numerical resolution, whose results cannot be extrapolated. By linearizing this equation by intervals, the method proposed here allows to express analytically, in any case, the phase currents, the torque and the copper losses, when the feeding voltage itself is constant by intervals. The model neglects saturation, but a simple adjustment of the inductance (chosen ad libitum) allows to deal with it. The calculation is immediate and perfectly accurate as long as the machine parameters themselves are well defined. Some results are given as examples for two usual feeding modes. Dans les machines à réluctance alimentées à haute fréquence par une source à tension constante, comme une batterie, le courant varie de manière difficilement prévisible, à cause de la variation des inductances avec la position du rotor, et souvent ne parvient pas à s'établir à une valeur de consigne imposée ; la f.é.m. “motionnelle” engendre des difficultés de communication qui s'aggravent avec l'augmentation de fréquence jusqu'à empêcher le fonctionnement. Tant pour optimiser la commande que pour dimensionner approximativement un moteur ; on doit pouvoir calculer simplement et rapidement le courant et la puissance ; or l'équation électrique, non linéaire, doit en principe être résolue numériquement et les résultats ne sont pratiquement pas extrapolables. En linéarisant par intervalles cette équation, la méthode proposée ici permer d'exprimer analytiquement et dans tous les cas les courants de phase, la puissance fournie et les pertes Joule, lorsque la tension aux bornes de l'enroulement est constante par morceaux. Le modèle utilisé néglige la saturation ; mais il est possible de tenir compte de celle-ci par des ajustements, facilement calculables, de la courbe d'inductance, quelle que soit son allure. Les calculs sont immédiats et parfaitement précis pour autant que les paramètres soient bien définis. Quelques résultats sont donnés à titre d'exemple, pour deux modes d'alimentation usuels.

DETERMINATION OF CHLOROETHENES IN ENVIRONMENTAL BIOLOGICAL SAMPLES USING GAS CHROMATOGRAPHY COUPLED WITH SOLID PHASE MICRO EXTRACTION

EPA Science Inventory

An analytical method has been developed to determine the chloroethene series, tetrachloroethene (PCE), trichloroethene (TCE),cisdichloroethene (cis-DCE) andtransdichloroethene (trans-DCE) in environmental biotreatment studies using gas chromatography coupled with a solid phase mi...

ISOLATING AND FRACTIONATING ORGANIC TOXICANTS IN SEDIMENTS: EVALUATION OF AN EXPERIMENTAL APPROACH

EPA Science Inventory

Most solid-phase sediment TIE techniques for organic chemicals have been focused on solid phase sorptive techniques, such as amending contaminated sediments with the carbonaceousresin, Ambersorb coconut charcoal, or XAD resin to reduce toxicity caused by organic contaminants. Cha...

ISOLATING AND EVALUATING ORGANIC TOXICANTS IN SEDIMENTS: EVALUATION OF AN EXPERIMENTAL APPROACH

EPA Science Inventory

Most solid-phase sediment toxicity identification and evaluation (TIE) techniques for organic chemicals have been focused on solid phase sorptive techniques, such as amending contaminated sediments with the carbonaceous resin, Ambersorb, coconut charcoal, or XAD resin to reduce t...

A review of solid-fluid selection options for optical-based measurements in single-phase liquid, two-phase liquid-liquid and multiphase solid-liquid flows

NASA Astrophysics Data System (ADS)

Wright, Stuart F.; Zadrazil, Ivan; Markides, Christos N.

2017-09-01

Experimental techniques based on optical measurement principles have experienced significant growth in recent decades. They are able to provide detailed information with high-spatiotemporal resolution on important scalar (e.g., temperature, concentration, and phase) and vector (e.g., velocity) fields in single-phase or multiphase flows, as well as interfacial characteristics in the latter, which has been instrumental to step-changes in our fundamental understanding of these flows, and the development and validation of advanced models with ever-improving predictive accuracy and reliability. Relevant techniques rely upon well-established optical methods such as direct photography, laser-induced fluorescence, laser Doppler velocimetry/phase Doppler anemometry, particle image/tracking velocimetry, and variants thereof. The accuracy of the resulting data depends on numerous factors including, importantly, the refractive indices of the solids and liquids used. The best results are obtained when the observational materials have closely matched refractive indices, including test-section walls, liquid phases, and any suspended particles. This paper reviews solid-liquid and solid-liquid-liquid refractive-index-matched systems employed in different fields, e.g., multiphase flows, turbomachinery, bio-fluid flows, with an emphasis on liquid-liquid systems. The refractive indices of various aqueous and organic phases found in the literature span the range 1.330-1.620 and 1.251-1.637, respectively, allowing the identification of appropriate combinations to match selected transparent or translucent plastics/polymers, glasses, or custom materials in single-phase liquid or multiphase liquid-liquid flow systems. In addition, the refractive indices of fluids can be further tuned with the use of additives, which also allows for the matching of important flow similarity parameters such as density and viscosity.

Effects of gravity reduction on phase equilibria. Part 1: Unary and binary isostructural solids

NASA Technical Reports Server (NTRS)

Larson, D. J., Jr.

1975-01-01

Analysis of the Skylab II M553 Experiment samples resulted in the hypothesis that the reduced gravity environment was altering the melting and solidification reactions. A theoretical study was conducted to define the conditions under which such alteration of phase relations is feasible, determine whether it is restricted to space processing, and, if so, ascertain which alloy systems or phase reactions are most likely to demonstrate such effects. Phase equilibria of unary and binary systems with a single solid phase (unary and isomorphous) were considered.

The simulation and experimental validation on gas-solid two phase flow in the riser of a dense fluidized bed

NASA Astrophysics Data System (ADS)

Wang, Xue-Yao; Jiang, Fan; Xu, Xiang; Wang, Sheng-Dian; Fan, Bao-Guo; Xiao, Yun-Han

2009-06-01

Gas-solid flow in dense CFB (circulating fluidized bed)) riser under the operating condition, superficial gas 15.5 m/s and solid flux 140 kg/m2s using Geldart B particles (sand) was investigated by experiments and CFD (computational fluid dynamics) simulation. The overall and local flow characteristics are determined using the axial pressure profiles and solid concentration profiles. The cold experimental results indicate that the axial solid concentration distribution contains a dilute region towards the up-middle zone and a dense region near the bottom and the top exit zones. The typical core-annulus structure and the back-mixing phenomenon near the wall of the riser can be observed. In addition, owing to the key role of the drag force of gas-solid phase, a revised drag force coefficient, based on the EMMS (energy-minimization multi-scale) model which can depict the heterogeneous character of gas-solid two phase flow, was proposed and coupled into the CFD control equations. In order to find an appropriate drag force model for the simulation of dense CFB riser, not only the revised drag force model but some other kinds of drag force model were used in the CFD. The flow structure, solid concentration, clusters phenomenon, fluctuation of two phases and axial pressure drop were analyzed. By comparing the experiment with the simulation, the results predicted by the EMMS drag model showed a better agreement with the experimental axial average pressure drop and apparent solid volume fraction, which proves that the revised drag force based on the EMMS model is an appropriate model for the dense CFB simulation.

Enhanced densification under shock compression in porous silicon

NASA Astrophysics Data System (ADS)

Lane, J. Matthew D.; Thompson, Aidan P.; Vogler, Tracy J.

2014-10-01

Under shock compression, most porous materials exhibit lower densities for a given pressure than that of a full-dense sample of the same material. However, some porous materials exhibit an anomalous, or enhanced, densification under shock compression. We demonstrate a molecular mechanism that drives this behavior. We also present evidence from atomistic simulation that silicon belongs to this anomalous class of materials. Atomistic simulations indicate that local shear strain in the neighborhood of collapsing pores nucleates a local solid-solid phase transformation even when bulk pressures are below the thermodynamic phase transformation pressure. This metastable, local, and partial, solid-solid phase transformation, which accounts for the enhanced densification in silicon, is driven by the local stress state near the void, not equilibrium thermodynamics. This mechanism may also explain the phenomenon in other covalently bonded materials.

Pig manure treatment by filtration.

PubMed

Kowalski, Zygmunt; Makara, Agnieszka; Matýsek, Dalibor; Hoffmann, Józef; Hoffmann, Krystyna

2013-01-01

A study of new pig manure treatment and filtration process was carried out. The advantage of the worked out technology is the method of incorporation of crystalline phase into solid organic part of manure. The obtained new solid phase of manure contains about 50% of crystalline phase forming a filtration aid that enables high effectiveness of manure filtration. The filtration rate of manure separation into solid and liquid fractions with pressure filter may achieve 1300-3000 kg/m(2)/h. The method makes it possible to maintain an overall average pollutant removal performance 90% for the chemical oxygen demand COD, > 99% for the suspended solids SS, to 47% for the total nitrogen content. The obtained results showed that the proposed technology being efficient and simple offers a possible solution to pig manure problems.

TANK48 CFD MODELING ANALYSIS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, S.

2011-05-17

The process of recovering the waste in storage tanks at the Savannah River Site (SRS) typically requires mixing the contents of the tank to ensure uniformity of the discharge stream. Mixing is accomplished with one to four dual-nozzle slurry pumps located within the tank liquid. For the work, a Tank 48 simulation model with a maximum of four slurry pumps in operation has been developed to estimate flow patterns for efficient solid mixing. The modeling calculations were performed by using two modeling approaches. One approach is a single-phase Computational Fluid Dynamics (CFD) model to evaluate the flow patterns and qualitativemore » mixing behaviors for a range of different modeling conditions since the model was previously benchmarked against the test results. The other is a two-phase CFD model to estimate solid concentrations in a quantitative way by solving the Eulerian governing equations for the continuous fluid and discrete solid phases over the entire fluid domain of Tank 48. The two-phase results should be considered as the preliminary scoping calculations since the model was not validated against the test results yet. A series of sensitivity calculations for different numbers of pumps and operating conditions has been performed to provide operational guidance for solids suspension and mixing in the tank. In the analysis, the pump was assumed to be stationary. Major solid obstructions including the pump housing, the pump columns, and the 82 inch central support column were included. The steady state and three-dimensional analyses with a two-equation turbulence model were performed with FLUENT{trademark} for the single-phase approach and CFX for the two-phase approach. Recommended operational guidance was developed assuming that local fluid velocity can be used as a measure of sludge suspension and spatial mixing under single-phase tank model. For quantitative analysis, a two-phase fluid-solid model was developed for the same modeling conditions as the single-phase model. The modeling results show that the flow patterns driven by four pump operation satisfy the solid suspension requirement, and the average solid concentration at the plane of the transfer pump inlet is about 12% higher than the tank average concentrations for the 70 inch tank level and about the same as the tank average value for the 29 inch liquid level. When one of the four pumps is not operated, the flow patterns are satisfied with the minimum suspension velocity criterion. However, the solid concentration near the tank bottom is increased by about 30%, although the average solid concentrations near the transfer pump inlet have about the same value as the four-pump baseline results. The flow pattern results show that although the two-pump case satisfies the minimum velocity requirement to suspend the sludge particles, it provides the marginal mixing results for the heavier or larger insoluble materials such as MST and KTPB particles. The results demonstrated that when more than one jet are aiming at the same position of the mixing tank domain, inefficient flow patterns are provided due to the highly localized momentum dissipation, resulting in inactive suspension zone. Thus, after completion of the indexed solids suspension, pump rotations are recommended to avoid producing the nonuniform flow patterns. It is noted that when tank liquid level is reduced from the highest level of 70 inches to the minimum level of 29 inches for a given number of operating pumps, the solid mixing efficiency becomes better since the ratio of the pump power to the mixing volume becomes larger. These results are consistent with the literature results.« less

[Gastric emptying of a solid-liquid meal in normal subjects: validity of the labeling (99mTc) of chicken liver by a multipuncture technic].

PubMed

Hostein, J; Capony, P; Busquet, G; Bost, R; Fournet, J

1985-04-01

For gastric emptying studies of a solid-liquid meal by the scintigraphic method, a valid isotope labeling method for each phase of the meal must be obtained. The aim of this study was to validate a simple chicken liver labeling method in normal subjects by multipuncture technic with 99mtechnetium. Labeling according to Meyer's method was chosen as a reference. Simultaneously, a study of the quality of liquid phase labeling by 111indium was done. The labeling process quality for each phase of the meal was assessed: a) in vitro, after incubation of the meal with human gastric juice (n = 12); b) in vivo, after meal ingestion and sequential collection of gastric contents by aspiration (n = 4). Furthermore, in 8 healthy volunteers, gastric emptying curves of the solid and liquid phases of the meal were determined scintigraphically and compared. Our results showed: a) for the solid phase: a good specificity of the marker, which was assessed in vitro and in vivo, after liver labeling with multipuncture technique (89 p. 100 and 92 p. 100 after 180 min, respectively); b) for the liquid phase: a good specificity of the marker in vitro and a poor specificity in vivo (82 p. 100 and 27 p. 100 after 180 min, respectively); c) similar half-gastric emptying times and cumulative percentages for the solid and liquid phases with both liver labeling methods. In conclusion, the multipuncture technique for chicken liver labeling may be used for gastric emptying studies in humans.

Determination of solid- and liquid-phase gastric emptying half times in cats by use of nuclear scintigraphy.

PubMed

Costello, M; Papasouliotis, K; Barr, F J; Gruffydd-Jones, T J; Caney, S M

1999-10-01

To use nuclear scintigraphy to establish a range of gastric emptying half times (t1/2) following a liquid or solid meal in nonsedated cats. 12 clinically normal 3-year-old domestic shorthair cats. A test meal of 75 g of scrambled eggs labeled with technetium Tc 99m tin colloid was fed to 10 of the cats, and solid-phase gastric emptying t1/2 were determined by use of nuclear scintigraphy. In a separate experiment, 8 of these cats plus an additional 2 cats were fed 18 ml (n = 5) or 36 ml (n = 5) of a nutrient liquid meal labeled with technetium Tc 99m pentetate. Liquid-phase gastric emptying t1/2 then were determined by use of scintigraphy. Solid-phase gastric emptying t1/2 were between 210 and 769 minutes (median, 330 minutes). Median liquid-phase gastric emptying t1/2 after ingestion of 18 or 36 ml of the test meal were 67 minutes (range, 60 to 96 minutes) and 117 minutes (range, 101 to 170 minutes), respectively. The median t1/2 determined for cats receiving 18 ml of the radiolabeled liquid was significantly less than that determined for cats receiving 36 ml of the test meal. The protocol was tolerated by nonsedated cats. Solid-phase gastric emptying t1/2 were prolonged, compared with liquid-phase t1/2, and a major factor governing the emptying rate of liquids was the volume consumed. Nuclear scintigraphy may prove useful in assessing gastric motility disorders in cats.

A solid-phase glycosyltransferase assay for high-throughput screening in drug discovery research.

PubMed

Donovan, R S; Datti, A; Baek, M G; Wu, Q; Sas, I J; Korczak, B; Berger, E G; Roy, R; Dennis, J W

1999-10-01

Glycosyltransferases mediate changes in glycosylation patterns which, in turn, may affect the function of glycoproteins and/or glycolipids and, further downstream, processes of development, differentiation, transformation and cell-cell recognition. Such enzymes, therefore, represent valid targets for drug discovery. We have developed a solid-phase glycosyltransferase assay for use in a robotic high-throughput format. Carbohydrate acceptors coupled covalently to polyacrylamide are coated onto 96-well plastic plates. The glycosyltransferase reaction is performed with recombinant enzymes and radiolabeled sugar-nucleotide donor at 37 degrees C, followed by washing, addition of scintillation counting fluid, and measurement of radioactivity using a 96-well beta-counter. Glycopolymer construction and coating of the plastic plates, enzyme and substrate concentrations, and linearity with time were optimized using recombinant Core 2 beta1-6-N-acetylglucosaminyltransferase (Core 2 GlcNAc-T). This enzyme catalyzes a rate-limiting reaction for expression of polylactosamine and the selectin ligand sialyl-Lewis(x) in O-glycans. A glycopolymer acceptor for beta1-6-N-acetylglucosaminyltransferase V was also designed and shown to be effective in the solid-phase assay. In a high-throughput screen of a microbial extract library, the coefficient of variance for positive controls was 9.4%, and high concordance for hit validation was observed between the Core 2 GlcNAc-T solid-phase assay and a standard solution-phase assay. The solid-phase assay format, which can be adapted for a variety of glycosyltransferase enzymes, allowed a 5-6 fold increase in throughput compared to the corresponding solution-phase assay.

Profil épidémiologique des pathologies respiratoires chez l’enfant à l’Hôpital d’Enfants de Rabat, Maroc

PubMed Central

Benchekroun, Ilham; Boubkraoui, Mohamed El Mahdi; Mekaoui, Nour; Karboubi, Lamia; Mahraoui, Chafiq; Dakhama, Badr Sououd Benjelloun

2017-01-01

Introduction Les pathologies respiratoires représentent un motif fréquent d'hospitalisation en pédiatrie. L'objectif de cette étude était d'évaluer le profil épidémiologique des pathologies respiratoires chez l'enfant à l'hôpital d'enfants de Rabat, Maroc. Méthodes Il s'agit d'une étude observationnelle transversale qui a concerné tous les cas d'enfants âgés de 3 mois à 15 ans hospitalisés pour une pathologie respiratoire au service de pneumoallergologie et infectiologie pédiatriques de l'hôpital d'enfants de Rabat sur une période d'une année, du 1 janvier 2014 au 31 décembre 2014. Résultats Sur 3537 patients hospitalisés, 2493 (70,5%) l'ont été pour une pathologie respiratoire. Les hospitalisations pour exacerbation d'asthme (p < 0,001), bronchiolite aigüe (p < 0,001) et dyspnée laryngée (p = 0,004) étaient plus fréquentes chez le garçon alors que les hospitalisations pour pneumopathie aigüe (p = 0,005), pour inhalation de corps étranger (p = 0,007) et pour coqueluche (p = 0,020) étaient plus fréquentes chez la fille. Les hospitalisations pour pneumopathie aigüe (p < 0,001), exacerbation de séquelles graves de virose (p < 0,001) et pour coqueluche (p < 0,001) étaient plus fréquentes chez le nourrisson. Les hospitalisations pour pneumopathie aigüe (p < 0,001) et pour coqueluche (p = 0,015) étaient plus fréquentes en période automnohivernale. Conclusion Les motifs d'hospitalisation étaient dominés par les exacerbations d'asthme et la bronchiolite aigüe, lesquelles étaient plus fréquentes chez le garçon. Les infections respiratoires, représentées par les pneumopathies aigües et la coqueluche, étaient plus fréquentes en période automnohivernale et touchaient plus le nourrisson. PMID:29675122

Biphasic fermentation is an efficient strategy for the overproduction of δ-endotoxin from Bacillus thuringiensis.

PubMed

Jisha, Veloorvalappil Narayanan; Smitha, Robinson Babysarojam; Priji, Prakasan; Sajith, Sreedharan; Benjamin, Sailas

2015-02-01

This study illustrates a biphasic solid-state fermentation (SSF) strategy for the overproduction of δ-endotoxin from Bacillus thuringiensis subsp. kurstaki (Btk) and also purification of δ-endotoxin from the solid-fermented medium. The fermentation strategy had two phases (biphasic); i.e., the first short phase was semisolid state (12 h), and the remaining long phase was strict SSF. To achieve the biphasic SSF, after 12 h (150 rpm, 37 °C) fermentation of the medium [Luria-Bertani (LB) supplemented with 30 % (w/v) raw soybean flour (phase I)], the supernatant in it was completely centrifuged out (1,000 × g, 10 min) aseptically for harvesting the extracellular enzymes as by-product. The resultant wet solid matter without free-flowing liquid but with embedded Btk was incubated 60 h more (phase II) for enhancing δ-endotoxin production at static condition (37 °C). Coupled with this, δ-endotoxin was purified by the modified phase separation method, and its purity was physically confirmed by both staining and microscopic techniques. The maximum δ-endotoxin yield from solid medium (48 h) was 15.8 mg/mL (recovery was 55-59 %) LB-equivalent, while that of LB control (recovery was 95 %) was only 0.43 mg/mL (72 h), i.e., thus, in comparison, 36.74-fold more yield in solid medium obtained by 24 h less gestation period. The purified crystal proteins showed apparent molecular weights (MWs) of 45, 35, and 6 kDa on sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). Briefly, this unique study physically demonstrates how Btk δ-endotoxin is purified (95-99 % purity) from solid-fermented matter for the first time, coupled with its overproduction at the expense of only 21.5 % higher production cost.

Unsteady numerical analysis of solid-liquid two-phase flow in stirred tank with double helical ribbon impeller

NASA Astrophysics Data System (ADS)

Bai, He; Chen, Xiangshan; Zhao, Guangyu; Xiao, Chenglei; Li, Chen; Zhong, Cheng; Chen, Yu

2017-08-01

In order to enhance the mixing process of soil contaminated by oil and water, one kind of double helical ribbon (DHR) impeller was developed. In this study, the unsteady simulation analysis of solid-liquid two-phase flow in stirring tank with DHR impeller was conducted by the the computational fluid dynamics and the multi-reference frame (MRF) method. It was found that at 0-3.0 s stage, the rate of liquid was greater than the rate of solid particles, while the power consumption was 5-6 times more than the smooth operation. The rates of the liquid and the solid particles were almost the same, and the required power was 32 KW at t > 3.0 s. The flow of the solid particles in the tank was a typical axial circle flow, and the dispersed sequence of the solid that was accumulated at the bottom of the tank was: the bottom loop region, the annular region near the wall of the groove and finally the area near axial center. The results show that the DHR impeller was suitable for the mixing of liquid-solid two-phase.

Triclinic-monoclinic-orthorhombic (T-M-O) structural transitions in phase diagram of FeVO4-CrVO4 solid solutions

NASA Astrophysics Data System (ADS)

Bera, Ganesh; Reddy, V. R.; Rambabu, P.; Mal, P.; Das, Pradip; Mohapatra, N.; Padmaja, G.; Turpu, G. R.

2017-09-01

Phase diagram of FeVO4-CrVO4 solid solutions pertinent with structural and magnetic phases is presented with unambiguous experimental evidences. Solid solutions Fe1-xCrxVO4 (0 ≤ x ≤ 1.0) were synthesized through the standard solid state route and studied by X-ray diffraction, scanning electron microscopy, energy dispersive spectra of X-rays, Raman spectroscopy, d.c. magnetization, and 57Fe Mössbauer spectroscopic studies. FeVO4 and CrVO4 were found to be in triclinic (P-1 space group) and orthorhombic structures (Cmcm space group), respectively. Cr incorporation into the FeVO4 lattice leads to the emergence of a new monoclinic phase dissimilar to the both end members of the solid solutions. In Fe1-xCrxVO4 up to x = 0.10, no discernible changes in the triclinic structure were found. A new structural monoclinic phase (C2/m space group) emerges within the triclinic phase at x = 0.125, and with the increase in Cr content, it gets stabilized with clear single phase signatures in the range of x = 0.175-0.25 as evidenced by the Rietveld analysis of the structures. Beyond x = 0.33, orthorhombic phase similar to CrVO4 (Cmcm space group) emerges and coexists with a monoclinic structure up to x = 0.85, which finally tends to stabilize in the range of x = 0.90-1.00. The Raman spectroscopic studies also confirm the structural transition. FeVO4 Raman spectra show the modes related to three nonequivalent V ions in the triclinic structure, where up to 42 Raman modes are observed in the present study. With the stabilization of structures having higher symmetry, the number of Raman modes decreases and the modes related to symmetry inequivalent sites collate into singular modes from the doublet structure. A systematic crossover from two magnetic transitions in FeVO4, at 21.5 K and 15.4 K to single magnetic transition in CrVO4, at 71 K (antiferromagnetic transition), is observed in magnetization studies. The intermediate solid solution with x = 0.15 shows two magnetic transitions, whereas in the compound with x = 0.33 one of the magnetic transitions disappears. 57Fe Mössbauer spectroscopic studies show a finger print evidence for disappearance of non-equivalent sites of Fe as the structure changes from Triclinic-Monoclinic-Orthorhombic phases with the increasing Cr content in Fe1-xCrxVO4. Comprehensive studies related to the structural changes in Fe1-xCrxVO4 solid solutions lead us to detailed phase diagrams which shall be characteristic for room temperature structural and temperature dependent magnetic transitions in these solid solutions, respectively.

Investigation of phase evolution of CaCu{sub 3}Ti{sub 4}O{sub 12} (CCTO) by in situ synchrotron high-temperature powder diffraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ouyang, Xin; Huang, Saifang; School of Materials Science and Technology, China University of Geosciences

2014-03-15

In situ synchrotron X-ray powder diffraction was used to study the high-temperature phase evolution of CaCu{sub 3}Ti{sub 4}O{sub 12} (CCTO) precursors prepared via solid-state and sol–gel methods. After the precursors are heated to 1225 °C, the CCTO phase is the main phase observed in the calcined powder, with the presence of some minor impurities. Comparing the two precursors, we found that the onset temperature for the CCTO phase formation is 800 °C in the sol–gel precursor, lower than that in the solid-state precursor (875 °C). Intermediate phases were only observed in the sol–gel precursor. Both precursors are able to bemore » calcined to sub-micrometric sized powders. Based on the synchrotron data along with differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA), the phase formation sequence and mechanism during calcination are proposed in this study. -- Graphical abstract: The in situ synchrotron HT-XRD patterns of CCTO sol–gel and solid-state precursor. Highlights: • Phase formation sequence/mechanism in two CCTO precursors has been established. • Formation temperature of CCTO via sol–gel method is lower than solid-state method. • Intermediate phases are only observed in the sol–gel precursor. • Both precursors are able to be calcined into sub-micrometric sized powders.« less

A CFD model for biomass combustion in a packed bed furnace

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karim, Md. Rezwanul; Department of Mechanical & Chemical Engineering, Islamic University of Technology, Gazipur 1704; Ovi, Ifat Rabbil Qudrat

Climate change has now become an important issue which is affecting environment and people around the world. Global warming is the main reason of climate change which is increasing day by day due to the growing demand of energy in developed countries. Use of renewable energy is now an established technique to decrease the adverse effect of global warming. Biomass is a widely accessible renewable energy source which reduces CO{sub 2} emissions for producing thermal energy or electricity. But the combustion of biomass is complex due its large variations and physical structures. Packed bed or fixed bed combustion is themore » most common method for the energy conversion of biomass. Experimental investigation of packed bed biomass combustion is difficult as the data collection inside the bed is challenging. CFD simulation of these combustion systems can be helpful to investigate different operational conditions and to evaluate the local values inside the investigation area. Available CFD codes can model the gas phase combustion but it can’t model the solid phase of biomass conversion. In this work, a complete three-dimensional CFD model is presented for numerical investigation of packed bed biomass combustion. The model describes the solid phase along with the interface between solid and gas phase. It also includes the bed shrinkage due to the continuous movement of the bed during solid fuel combustion. Several variables are employed to represent different parameters of solid mass. Packed bed is considered as a porous bed and User Defined Functions (UDFs) platform is used to introduce solid phase user defined variables in the CFD. Modified standard discrete transfer radiation method (DTRM) is applied to model the radiation heat transfer. Preliminary results of gas phase velocity and pressure drop over packed bed have been shown. The model can be useful for investigation of movement of the packed bed during solid fuel combustion.« less

Results of Copper-Silver Rail Materials Tests

DTIC Science & Technology

2006-05-01

dislocation-dense grain structure. An annealing, recrystallization , and re-straining model is proposed to predict the bandwidth within which the...darker phase is the copper-rich solid solution, while the lighter regions are the eutectic structure consisting of both copper-rich and silver-rich solid...solutions. The eutectic phase ribbons consist of finer copper and silver filaments [1], [5]. The two phases are inhomogeneously deformed during the

CRYOCHEM, Thermodynamic Model for Cryogenic Chemical Systems: Solid-Vapor and Solid-Liquid-Vapor Phase Equilibria Toward Applications on Titan and Pluto

NASA Astrophysics Data System (ADS)

Tan, S. P.; Kargel, J. S.; Adidharma, H.; Marion, G. M.

2014-12-01

Until in-situ measurements can be made regularly on extraterrestrial bodies, thermodynamic models are the only tools to investigate the properties and behavior of chemical systems on those bodies. The resulting findings are often critical in describing physicochemical processes in the atmosphere, surface, and subsurface in planetary geochemistry and climate studies. The extremely cold conditions on Triton, Pluto and other Kuiper Belt Objects, and Titan introduce huge non-ideality that prevents conventional models from performing adequately. At such conditions, atmospheres as a whole—not components individually—are subject to phase equilibria with their equilibrium solid phases or liquid phases or both. A molecular-based thermodynamic model for cryogenic chemical systems, referred to as CRYOCHEM, the development of which is still in progress, was shown to reproduce the vertical composition profile of Titan's atmospheric methane measured by the Huygens probe (Tan et al., Icarus 2013, 222, 53). Recently, the model was also used to describe Titan's global circulation where the calculated composition of liquid in Ligeia Mare is consistent with the bathymetry and microwave absorption analysis of T91 Cassini fly-by data (Tan et al., 2014, submitted). Its capability to deal with equilibria involving solid phases has also been demonstrated (Tan et al., Fluid Phase Equilib. 2013, 360, 320). With all those previous works done, our attention is now shifting to the lower temperatures in Titan's tropopause and on Pluto's surface, where much technical development remains for CRYOCHEM to assure adequate performance at low temperatures. In these conditions, solid-vapor equilibrium (SVE) is the dominant phase behavior that determines the composition of the atmosphere and the existing ices. Another potential application is for the subsurface phase equilibrium, which also involves liquid, thus three-phase equilibrium: solid-liquid-vapor (SLV). This presentation will discuss the current state of CRYOCHEM in representing the SVE and SLV of chemical systems at temperatures and pressures relevant to Titan's tropopause and Pluto and the upper crusts of these objects.

The cephalic phase insulin response to nutritive and low-calorie sweeteners in solid and beverage form.

PubMed

Dhillon, Jaapna; Lee, Janice Y; Mattes, Richard D

2017-11-01

The purpose of the study was to examine the role of the cephalic phase insulin response (CPIR) following exposure to nutritive and low-calorie sweeteners in solid and beverage form in overweight and obese adults. In addition, the role of learning on the CPIR to nutritive and low-calorie sweetener exposure was tested. Sixty-four overweight and obese adults (age: 18-50years, BMI: 24-37kg/m 2 , body fat percentage>25% for men and >32% for women) were sham-fed (at 2-minute intervals for 14min) a randomly assigned test load comprised of a nutritive (sucrose) or low-calorie sweetener (sucralose) in beverage or solid form in phase 1 of the study. A 2-3ml blood sample was collected before and 2, 6, 10, 14, 61, 91 and 121min after oral exposure for serum insulin and glucose analysis. During phase 2, participants underwent a 2-week training period to facilitate associative learning between the sensory properties of test loads and their post-ingestive effects. In phase 3, participants were retested for their cephalic phase responses as in phase 1. Participants were classified as responders if they demonstrated a positive insulin response (rise of serum insulin above baseline i.e. Δ insulin) 2min post-stimulus in phase 1. Among responders exposed to the same sweetener in Phases 1 and 3, the proportion of participants that displayed a rise of insulin with oral exposure to sucralose was significantly greater when the stimulus was in the solid form compared to the beverage form. Sucralose and sucrose exposure elicited similarly significant increases in serum insulin 2min after exposure and significant decreases after 2min in responders in both food forms. The solid food form elicited greater CPIR over 2, 6 and 10min than the beverage form. There was no effect of learning on insulin responses after training. The results indicate the presence of a significant CPIR in a subset of individuals with overweight or obesity after oral exposure to sucralose, especially when present in solid food form. Future studies must confirm the reliability of this response. Copyright © 2017 Elsevier Inc. All rights reserved.

Phase Transition Enthalpy Measurements of Organic and Organometallic Compounds and Ionic Liquids. Sublimation, Vaporization, and Fusion Enthalpies from 1880 to 2015. Part 2. C11-C192

NASA Astrophysics Data System (ADS)

Acree, William; Chickos, James S.

2017-03-01

The second part of this compendium concludes with a collection of phase change enthalpies of organic molecules inclusive of C11-C192 reported over the period 1880-2015. Also included are phase change enthalpies including fusion, vaporization, and sublimation enthalpies for organometallic, ionic liquids, and a few inorganic compounds. Paper I of this compendium, published separately, includes organic compounds from C1 to C10 and describes a group additivity method for evaluating solid, liquid, and gas phase heat capacities as well as temperature adjustments of phase changes. Paper II of this compendium also includes an updated version of a group additivity method for evaluating total phase change entropies which together with the fusion temperature can be useful in estimating total phase change enthalpies. Other uses include application in identifying potential substances that either form liquid or plastic crystals or exhibit additional phase changes such as undetected solid-solid transitions or behave anisotropically in the liquid state.

Freezing Transition Studies Through Constrained Cell Model Simulation

NASA Astrophysics Data System (ADS)

Nayhouse, Michael; Kwon, Joseph Sang-Il; Heng, Vincent R.; Amlani, Ankur M.; Orkoulas, G.

2014-10-01

In the present work, a simulation method based on cell models is used to deduce the fluid-solid transition of a system of particles that interact via a pair potential, , which is of the form with . The simulations are implemented under constant-pressure conditions on a generalized version of the constrained cell model. The constrained cell model is constructed by dividing the volume into Wigner-Seitz cells and confining each particle in a single cell. This model is a special case of a more general cell model which is formed by introducing an additional field variable that controls the number of particles per cell and, thus, the relative stability of the solid against the fluid phase. High field values force configurations with one particle per cell and thus favor the solid phase. Fluid-solid coexistence on the isotherm that corresponds to a reduced temperature of 2 is determined from constant-pressure simulations of the generalized cell model using tempering and histogram reweighting techniques. The entire fluid-solid phase boundary is determined through a thermodynamic integration technique based on histogram reweighting, using the previous coexistence point as a reference point. The vapor-liquid phase diagram is obtained from constant-pressure simulations of the unconstrained system using tempering and histogram reweighting. The phase diagram of the system is found to contain a stable critical point and a triple point. The phase diagram of the corresponding constrained cell model is also found to contain both a stable critical point and a triple point.

Monitoring gas-phase CO2 in the headspace of champagne glasses through combined diode laser spectrometry and micro-gas chromatography analysis.

PubMed

Moriaux, Anne-Laure; Vallon, Raphaël; Parvitte, Bertrand; Zeninari, Virginie; Liger-Belair, Gérard; Cilindre, Clara

2018-10-30

During Champagne or sparkling wine tasting, gas-phase CO 2 and volatile organic compounds invade the headspace above glasses, thus progressively modifying the chemical space perceived by the consumer. Gas-phase CO 2 in excess can even cause a very unpleasant tingling sensation perturbing both ortho- and retronasal olfactory perception. Monitoring as accurately as possible the level of gas-phase CO 2 above glasses is therefore a challenge of importance aimed at better understanding the close relationship between the release of CO 2 and a collection of various tasting parameters. Here, the concentration of CO 2 found in the headspace of champagne glasses served under multivariate conditions was accurately monitored, all along the 10 min following pouring, through a new combined approach by a CO 2 -Diode Laser Sensor and micro-gas chromatography. Our results show the strong impact of various tasting conditions (volume dispensed, intensity of effervescence, and glass shape) on the release of gas-phase CO 2 above the champagne surface. Copyright © 2018 Elsevier Ltd. All rights reserved.

40 CFR 63.7710 - What are my operation and maintenance requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... gases from mold vents in pouring areas and pouring stations that use a sand mold system. This operation... including quality assurance procedures. (iv) How the bag leak detection system will be maintained including...) Procedures for providing an ignition source to mold vents of sand mold systems in each pouring area and...

Temperature-Controlled High-Speed AFM: Real-Time Observation of Ripple Phase Transitions.

PubMed

Takahashi, Hirohide; Miyagi, Atsushi; Redondo-Morata, Lorena; Scheuring, Simon

2016-11-01

With nanometer lateral and Angstrom vertical resolution, atomic force microscopy (AFM) has contributed unique data improving the understanding of lipid bilayers. Lipid bilayers are found in several different temperature-dependent states, termed phases; the main phases are solid and fluid phases. The transition temperature between solid and fluid phases is lipid composition specific. Under certain conditions some lipid bilayers adopt a so-called ripple phase, a structure where solid and fluid phase domains alternate with constant periodicity. Because of its narrow regime of existence and heterogeneity ripple phase and its transition dynamics remain poorly understood. Here, a temperature control device to high-speed atomic force microscopy (HS-AFM) to observe dynamics of phase transition from ripple phase to fluid phase reversibly in real time is developed and integrated. Based on HS-AFM imaging, the phase transition processes from ripple phase to fluid phase and from ripple phase to metastable ripple phase to fluid phase could be reversibly, phenomenologically, and quantitatively studied. The results here show phase transition hysteresis in fast cooling and heating processes, while both melting and condensation occur at 24.15 °C in quasi-steady state situation. A second metastable ripple phase with larger periodicity is formed at the ripple phase to fluid phase transition when the buffer contains Ca 2+ . The presented temperature-controlled HS-AFM is a new unique experimental system to observe dynamics of temperature-sensitive processes at the nanoscopic level. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

COMPARING THE SOLID PHASE AND SALINE EXTRACT MICROTOX(R) ASSAYS FOR TWO PAH CONTAMINATED SOILS

EPA Science Inventory

The performance of remedial treatments is typically evaluated by measuring the concentration of specific chemicals. By adding toxicity bioassays to treatment evaluations, a fuller understanding of treatment performance is obtained. The solid phase Microtox assay is one potenti...

TOXICITY CHARACTERIZATION PROCEDURES FOR ORGANIC TOXICANTS IN BULK SEDIMENTS

EPA Science Inventory

We have been pursuing development of toxicant characterization, isolation, and identification procedures for organic toxicants that can be applied in the context of 10-d solid-phase sediment tests measuring survival and growth of freshwater in the context of 10-d solid-phase sedi...

Immobilization of organic radioactive and non-radioactive liquid waste in a composite matrix

DOE Office of Scientific and Technical Information (OSTI.GOV)

Galkin, Anatoliy; Gelis, Artem V.; Castiglioni, Andrew J.

A method for immobilizing liquid radioactive waste is provided, the method having the steps of mixing waste with polymer to form a non-liquid waste; contacting the non-liquid waste with a solidifying agent to create a mixture, heating the mixture to cause the polymer, waste, and filler to irreversibly bind in a solid phase, and compressing the solid phase into a monolith. The invention also provides a method for immobilizing liquid radioactive waste containing tritium, the method having the steps of mixing liquid waste with polymer to convert the liquid waste to a non-liquid waste, contacting the non-liquid waste with amore » solidifying agent to create a mixture, heating the mixture to form homogeneous, chemically stable solid phase, and compressing the chemically stable solid phase into a final waste form, wherein the polymer comprises approximately a 9:1 weight ratio mixture of styrene block co-polymers and cross linked co-polymers of acrylamides.« less

Solid-liquid surface tensions of critical nuclei and nucleation barriers from a phase-field-crystal study of a model binary alloy using finite system sizes.

PubMed

Choudhary, Muhammad Ajmal; Kundin, Julia; Emmerich, Heike; Oettel, Martin

2014-08-01

Phase-field-crystal (PFC) modeling has emerged as a computationally efficient tool to address crystal growth phenomena on atomistic length and diffusive time scales. We use a two-dimensional phase-field-crystal model for a binary system based on Elder et al. [Phys. Rev. B 75, 064107 (2007)] to study critical nuclei and their liquid-solid phase boundaries, in particular the nucleus size dependence of the liquid-solid interface tension as well as of the nucleation barrier. Critical nuclei are stabilized in finite systems of various sizes, however, the extracted interface tension as function of the nucleus radius r is independent of system size. We suggest a phenomenological expression to describe the dependence of the extracted interface tension on the nucleus radius r for the liquid-solid system. Moreover, the numerical PFC results show that this dependency can not be fully described by the nonclassical Tolman formula.

Solid-phase receptor binding assay for /sup 125/I-hCG

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bortolussi, M.; Selmin, O.; Colombatti, A.

1987-01-01

A solid-phase radioligand-receptor assay (RRA) to measure the binding of /sup 125/I-labelled human chorionic gonadotropin (/sup 125/I-hCG) to target cell membranes has been developed. The binding of /sup 125/I-hCG to membranes immobilized on the wells of microtitration plates reached a maximum at about 3 hours at 37 degrees C, was saturable, displayed a high affinity (Ka = 2.4 X 10(9) M-1) and was specifically inhibited by unlabelled hCG. In comparison with RRAs carried out with membranes in suspension, the solid-phase RRA is significantly simpler and much faster to perform as it avoids centrifugation or filtration procedures. The solid-phase RRA wasmore » adapted profitably to process large numbers of samples at the same time. It proved particularly useful as a screening assay to detect anti-hCG monoclonal antibodies with high inhibitory activity for binding of /sup 125/I-hCG to its receptors.« less

Evaluation of potential for reuse of industrial wastewater using metal-immobilized catalysts and reverse osmosis.

PubMed

Choi, Jeongyun; Chung, Jinwook

2015-04-01

This report describes a novel technology of reusing the wastewater discharged from the display manufacturing industry through an advanced oxidation process (AOP) with a metal-immobilized catalyst and reverse osmosis (RO) in the pilot scale. The reclaimed water generated from the etching and cleaning processes in display manufacturing facilities was low-strength organic wastewater and was required to be recycled to secure a water source. For the reuse of reclaimed water to ultrapure water (UPW), a combination of solid-phase AOP and RO was implemented. The removal efficiency of TOC by solid-phase AOP and RO was 92%. Specifically, the optimal acid, pH, and H2O2 concentrations in the solid-phase AOP were determined. With regard to water quality and operating costs, the combination of solid-phase AOP and RO was superior to activated carbon/RO and ultraviolet AOP/anion polisher/coal carbon. Copyright © 2014 Elsevier Ltd. All rights reserved.

Dynamics of excimer laser ablation of thin tungsten films studied by fast photography

NASA Astrophysics Data System (ADS)

Toth, Zsolt; Hopp, Bela; Kantor, Zoltan; Ignacz, Ferenc; Szoerenyi, Tamas; Bor, Zsolt

1994-09-01

The time evolution of ablation and material transport during ArF excimer laser induced blow off of tungsten films from glass substrates is studied by fast photography using delayed dye laser pulses. The analysis of experimental results combined with heat flow calculations provides evidence that tungsten removal in the solid phase is the dominant mechanism in the 40 - 200 mJ/cm2 fluence domain, while partially inhomogeneous melting is observed between 200 and 800 mJ/cm2. In this fluence range, solid fragments and a halo consisting of molten droplets are observed indicating spatial separation of the two phases. The molten phase advances faster, forming a protective mist in front of the solid piece(s). At yet higher fluences (800 - 1000 mJ/cm2), a well separated solid phase could be recorded under the halo although model calculations suggest full vaporization of the layer. This unexpected phenomenon is explained by the optical shielding effect of the halo.

Les fluctuations supraconductrices dans le compose praseodyme-cerium-oxyde de cuivre

NASA Astrophysics Data System (ADS)

Renaud, Jacques

Ce travail etudie les fluctuations supraconductrices dans le compose supraconducteur a haute temperature critique dope aux electrons Pr2-xCe xCuO4+delta. La technique utilisee pour sonder ces fluctuations est le transport electrique DC dans le plan ab. Il s'agit, a notre connaissance, de la premiere etude de ce type dans la classe generale des supraconducteurs a haute temperature critique dopes aux electrons et, plus particulierement, dans Pr2-xCe xCuO4+delta. De plus, l'etude est effectuee pour trois regimes de dopage, soit sous-dope x = 0.135, dopage optimal x = 0.15 et surdope x = 0.17. Les echantillons etudies sont des couches minces d'epaisseur plus grande que 100 nm crues par ablation laser. Les mesures electriques DC effectuees dans ce travail sont la resistance en reponse lineaire et les courbes IV en reponse non lineaire en fonction de la temperature. La mise en oeuvre experimentale de ces mesures a necessite une grande attention au filtrage et aux effets de chauffage a haut courant. Nous montrons que, sans cette attention, les donnees experimentales sont toujours erronees dans le regime pertinent pour nos echantillons. Les resultats pour le dopage optimal x = 0.15 sont expliques de facon tres convaincante dans le cadre de fluctuations purement 2D. D'abord, le regime des fluctuations gaussiennes est tres bien decrit par le modele d'Aslamazov-Larkin en deux dimensions. Ensuite, le regime de fluctuations critiques, se trouvant a plus basse temperature que le regime gaussien, est tres bien decrit par la physique 2D de Kosterlitz-Thouless. Dans cette analyse, les deux regimes ont des temperatures critiques coherentes entre elles, ce qui semble confirmer ce scenario 2D. Une analyse des donnees dans le cadre de fluctuations 3D est exploree mais donne des conclusions incoherentes. Les resultats pour les autres dopages sont qualitativement equivalents avec le dopage optimal et permettent donc une explication purement 2D. Par contre, contrairement au dopage optimal, les effets du desordre semblent etre tres importants. Une analyse detaillee de tous ces resultats semble indiquer que les signatures 2D in identifiees proviennent vraisemblablement de plans paralleles decouples formes d'environ 4 plans CuO2 couples. On discute de cette mise en ordre partielle comme une possible consequence d'une separation de phase isolante antiferromagnetique/supraconducteur. La largeur de la transition en fonction du dopage est aussi analysee dans le but de mettre en lumiere un possible effet du pseudogap. On montre que nos mesures ne supportent pas une telle interpretation.

Elaboration d'un plan de transition et de mise en oeuvre pour ameliorer la gestion de l'obsolescence dans une entreprise du secteur aeronautique =

NASA Astrophysics Data System (ADS)

Conrad, Heloise

L'evolution technologique des composants electroniques entraine des problemes de gestion de l'obsolescence dans le secteur aeronautique. Les systemes aeronautiques ont en effet des durees de vie nettement superieures aux composants qu'ils contiennent. Cette difference de duree de vie et les normes strictes propres a l'aeronautique obligent les constructeurs a mettre en place une gestion efficace de l'obsolescence pour eviter les couts supplementaires de maintenance et de retards. De plus, a cause des faibles volumes de production qu'ils representent, les constructeurs aeronautiques n'ont que peu de controle sur leur chaine d'approvisionnement. La litterature offre beaucoup d'etudes sur l'obsolescence, appliquees a l'aeronautique. Les auteurs recommandent de mettre en place des processus de gestion et de prevision de l'obsolescence, et de construire des relations de collaboration avec leurs fournisseurs, qui ont plus de visibilite sur la chaine d'approvisionnement. Cette recherche presente d'abord l'elaboration d'une liste de criteres de bonne gestion de l'obsolescence, ainsi que la creation d'une methode de generation de plan de transition et de mise en oeuvre de l'amelioration de la gestion et de la prevision de l'obsolescence pour un cas concret. La methode est creee pour un manufacturier aeronautique ne possedant pas de systemes de gestion proactive ou de prevision de l'obsolescence. La creation de la methode s'est faite en suivant la methodologie de la science de la conception, en impliquant les employes concernes par la gestion de l'obsolescence. La methode comporte douze (12) etapes, amenant au developpement du plan de transition et de mise en oeuvre. Pour applique la methode, divers entretiens individuels et de groupe ont ete realises. Ces entretiens ont aussi permis de lister les criteres de gestion et de prevision efficaces de l'obsolescence. Cette liste a ete comparee avec les criteres issus de la litterature. En respect des besoins enonces par les employes et des conseils d'un industriel expert en obsolescence des composants avioniques, le plan de transition et de mise en oeuvre cree se divise en trois (3) phases : 1) amelioration de la gestion de l'obsolescence, 2) amelioration de la prevision de l'obsolescence et 3) gestion des fournisseurs. Meme si le plan de transition n'a pas ete applique dans l'entreprise partenaire, la methode et le plan cree ont ete approuves par les employes et utilisateurs.

Using colloidal silica as isolator, diverter and blocking agent for subsurface geological applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bourcier, William L.; Roberts, Sarah K.; Roberts, Jeffery J.

A system for blocking fast flow paths in geological formations includes preparing a solution of colloidal silica having a nonviscous phase and a solid gel phase. The solution of colloidal silica is injected into the geological formations while the solution of colloidal silica is in the nonviscous phase. The solution of colloidal silica is directed into the fast flow paths and reaches the solid gel phase in the fast flow paths thereby blocking flow of fluid in the fast paths.

Singaporean college students overpour drinks similar to Western populations: influence of peer presence in a simulated alcohol-pouring task.

PubMed

Zandy, Shannon L; Pang, Joyce S; Ho, Moon-Ho Ringo; Matthews, Douglas B

2013-11-01

College drinking is a global health concern. However, most studies originate from countries with high alcohol consumption. In the United States, college students overpour a standard alcoholic drink, yet it is unclear if this remains true in countries with low alcohol consumption. Additionally, in college, peer influence is the greatest predictor of drinking behavior, yet it is unknown if social norms affect how students pour drinks. This study examined how male college students, in a country with low alcohol consumption, define standard drinks, and if the presence of an unfamiliar peer affects how students pour during a simulated alcohol-pouring task. Male undergraduate students (n = 105) underwent baseline assessments of impulsivity, self-monitoring, religiosity, and drinking characteristics. Participants poured fluid into empty cups of different sizes to equal a standard serving of beer or shot of liquor. There were 2 groups based on gender of experimenter. Within each group, participants were randomly assigned to Alone or Dyad condition. In the Alone condition, students were instructed to pour only for themselves. In the Dyad condition, students were instructed to pour for themselves and the experimenter. The volumes poured by the students were compared with standards used in Singapore and the United States. Collapsed across container size, students overpoured shots by 50% and beer by 100% when compared to the standard drink definition in Singapore. When using a more liberal definition, students overpoured beer by 25%, but did not overpour shots. In the presence of an unfamiliar peer, overpouring decreased by 10% for beer. The current data show that college students, in a country with low alcohol consumption, overestimate standard alcoholic drinks similar to their Western counterparts and use social norms to determine how much to pour for a drink when confronted with an unfamiliar peer. Efforts toward creating internationally recognized standard drink definitions should be considered. Copyright © 2013 by the Research Society on Alcoholism.

Detailed monitoring of two biogas plants and mechanical solid-liquid separation of fermentation residues.

PubMed

Bauer, Alexander; Mayr, Herwig; Hopfner-Sixt, Katharina; Amon, Thomas

2009-06-01

The Austrian "green electricity act" (Okostromgesetz) has led to an increase in biogas power plant size and consequently to an increased use of biomass. A biogas power plant with a generating capacity of 500 kW(el) consumes up to 38,000 kg of biomass per day. 260 ha of cropland is required to produce this mass. The high water content of biomass necessitates a high transport volume for energy crops and fermentation residues. The transport and application of fermentation residues to farmland is the last step in this logistic chain. The use of fermentation residues as fertilizer closes the nutrient cycle and is a central element in the efficient use of biomass for power production. Treatment of fermentation residues by separation into liquid and solid phases may be a solution to the transport problem. This paper presents detailed results from the monitoring of two biogas plants and from the analysis of the separation of fermentation residues. Furthermore, two different separator technologies for the separation of fermentation residues of biogas plants were analyzed. The examined biogas plants correspond to the current technological state of the art and have designs developed specifically for the utilization of energy crops. The hydraulic retention time ranged between 45.0 and 83.7 days. The specific methane yields were 0.40-0.43 m(3)N CH(4) per kg VS. The volume loads ranged between 3.69 and 4.00 kg VS/m(3). The degree of degradation was between 77.3% and 82.14%. The screw extractor separator was better suited for biogas slurry separation than the rotary screen separator. The screw extractor separator exhibited a high throughput and good separation efficiency. The efficiency of slurry separation depended on the dry matter content of the fermentation residue. The higher the dry matter content, the higher the proportion of solid phase after separation. In this project, we found that the fermentation residues could be divided into 79.2% fluid phase with a dry matter content of 4.5% and 20.8% solid phase with a dry matter content of 19.3%. Dry matter, volatile solids and carbon, raw ash and phosphate--in relation to the mass--accumulated strongly in the solid phase. Nitrogen and ammonia nitrogen were slightly enriched in the solid phase. Only the potassium content decreased slightly in the solid phase.

Complete solids retention activated sludge process.

PubMed

Amanatidou, E; Samiotis, G; Trikoilidou, E; Pekridis, G; Tsikritzis, L

2016-01-01

In a slaughterhouse's full-scale extended aeration activated sludge wastewater treatment plant (WWTP), operating under complete solids retention time, the evolution of mixed liquor suspended solids (MLSS) and mixed liquor volatile suspended solids (MLVSS) concentration, food to micro-organisms ratio (F/M) and substrate utilization rate (SUR) were studied for over a year. Biomass growth phases in correlation to sludge biological and morphological characteristics were studied. Three distinguished growth phases were observed during the 425 days of monitoring. The imposed operational conditions led the process to extended biomass starvation conditions, minimum F/M, minimum SUR and predator species growth. MLSS and MLVSS reached a stabilization phase (plateau phase) where almost zero sludge accumulation was observed. The concept of degradation of the considered non-biodegradable particulate compounds in influent and in biomass (cell debris) was also studied. Comparison of evolution of observed sludge yields (Yobs) in the WWTP with Yobs predictions by activated sludge models verified the degradation concept for the considered non-biodegradable compounds. Control of the sedimentation process was achieved, by predicting the solids loading rate critical point using state point analysis and stirred/unstirred settling velocity tests and by applying a high return activated sludge rate. The nitrogen gas related sedimentation problems were taken into consideration.

Phase formation and UV luminescence of Gd3+ doped perovskite-type YScO3

NASA Astrophysics Data System (ADS)

Shimizu, Yuhei; Ueda, Kazushige

2016-10-01

Synthesis of pure and Gd3+doped perovskite-type YScO3 was attempted by a polymerized complex (PC) method and solid state reaction (SSR) method. Crystalline phases and UV luminescence of samples were examined with varying heating temperatures. The perovskite-type single phase was not simply formed in the SSR method, as reported in some literatures, and two cubic C-type phases of starting oxide materials remained forming slightly mixed solid solutions. UV luminescence of Gd3+ doped samples increased with an increase in heating temperatures and volume of the perovskite-type phase. In contrast, a non-crystalline precursor was crystallized to a single C-type phase at 800 °C in the PC method forming a completely mixed solid solution. Then, the phase of perovskite-type YScO3 formed at 1200 °C and its single phase was obtained at 1400 °C. It was revealed that high homogeneousness of cations was essential to generate the single perovskite-phase of YScO3. Because Gd3+ ions were also dissolved into the single C-type phase in Gd3+ doped samples, intense UV luminescence was observed above 800 °C in both C-type phase and perovskite-type phase.

Study of liquid?liquid demixing from drug solution

NASA Astrophysics Data System (ADS)

Lafferrère, Laurent; Hoff, Christian; Veesler, Stéphane

2004-09-01

In pharmaceutical industry, a deep understanding of the phase diagram is required in design of crystallization processes. We have investigated the phase diagram of a pharmaceutical compound (C 35H 41Cl 2N 3O 2) in a mixture of ethanol/water. This phase diagram exhibits a solid-solid (polymorphism) and a liquid-liquid-phase separation (LLPS) as a function of temperature and drug substance concentration. This study focuses on the LLPS which is metastable with respect to the crystallization of the two polymorphs FI and FII of C 35H 41Cl 2N 3O 2 in an ethanol/water mixture. The LLPS is metastable towards the solubility curve on the whole solvent-solute concentrations and temperature range studied. The LLPS occurred within the metastable zone for crystallization. In our experiments the liquid-liquid-phase transition prevented the drug from crystallizing, while it changed the medium and the conditions of crystallization, which consequently affected the process. The coexistence curves for the liquid phases, also named TL-L boundary, and the spinodal line were measured for a ternary mixture of water-drug-ethanol at atmospheric pressure over a temperature range of 10-50°C. This temperature range corresponds to that used in the crystallization process. Static Light Scattering, HPLC measurements and Karl-Fischer titration were applied to investigate the drug-phase diagram. The isoplethe section of the phase diagram exhibits four regions: one homogeneous (one liquid) and three two-phases (two regions with one liquid+one solid and one region with two liquids), the two solids phases being two polymorphs.

Novel Methods of Digital Phase Shifting to Achieve Arbitrary Values of Time Delay,

DTIC Science & Technology

1985-09-01

ACHIEVE ARBITRARY VALUES OF TIME DELAY A. Mohammed DTIC ELECTEI DEC 0 5 SSEi SD Defence Centre de U.j Research Recherches pour la A- Establishment...velles m ~thodes: la premi~re fait appel i une technique de fenitrage, et la deuxiirme, i un 6chantillonnage des fr6quences. Dans les deux m6thodes...toute m6thode de conception do d~phaseurs numhriques. Do plus, dans la m ~thode do I ’chantillonnage des fr~quences, on introduit le concept do plage

Synthesis of peptides containing overlapping lanthionine bridges on the solid phase: an analogue of rings D and E of the lantibiotic nisin.

PubMed

Mothia, Begum; Appleyard, Antony N; Wadman, Sjoerd; Tabor, Alethea B

2011-08-19

A methodology for the solid-phase synthesis of the overlapping lanthionine bridges found in many lantibiotics has been developed. A novel Teoc/TMSE-protected lanthionine derivative has been synthesized, and this lanthionine, and an Aloc/allyl-protected lanthionine derivative, have been incorporated into a linear peptide using solid-phase peptide synthesis. Selective deprotection of the silyl protecting groups, followed by sequential cyclization, deprotection of the allyl protecting groups, and further cyclization, enabled the regioselective formation of an analogue of rings D and E of nisin. © 2011 American Chemical Society

Two-phase non-Newtonian hydrodynamic modeling of slurries

NASA Astrophysics Data System (ADS)

Wang, C. S.; Lyczkowski, R. W.; Berry, G. F.

The two-phase hydrodynamic theory of fluid/solid flow has been extended to incorporate the constitutive relationship for power-law non-Newtonian behavior. A model has been developed to predict the spatial and temporal variations in solids and liquid velocities and concentration of non-Newtonian slurries under high shear rates in diesel engine injection systems. Comparisons between the present non-Newtonian two-phase theory and the conventional theory have also been made. Selected results for diesel injection nozzle applications are presented. The results from this model can be used to calculate directly the erosion rates at the nozzle boundaries and the solids loading at the nozzle exit.

Separation and purification of thymopentin with molecular imprinting membrane by solid phase extraction disks.

PubMed

Wang, Chaoli; Hu, Xiaoling; Guan, Ping; Wu, Danfeng; Qian, Liwei; Li, Ji; Song, Renyuan

2015-01-01

The synthesis and performance of molecularly imprinted membranes (MIMs) as a solid phase extraction packing materials for the separation and purification of thymopentin from crude samples was described. In order to increase structural selectivity and imprinting efficiency, surface-initiated ATRP and ionic liquid (1-vinyl-3-ethyl acetate imidazolium chloride) were used to prepare molecularly imprinting membranes. The results demonstrated that solid phase extraction disks stuffed by MIMs with ionic liquids as functional monomer demonstrated high isolation and purification of performance to the thymopentin. The molecular recognition of thymopentin was analyzed by using molecular modeling software. Copyright © 2014 Elsevier B.V. All rights reserved.

The role of the "Casimir force analogue" at the microscopic processes of crystallization and melting

NASA Astrophysics Data System (ADS)

Chuvildeev, V. N.; Semenycheva, A. V.

2016-10-01

Melting (crystallization), a phase transition from a crystalline solid to a liquid state, is a common phenomenon in nature. We suggest a new factor, "the Casimir force analogue", to describe mechanisms of melting and crystallization. The Casimir force analogue is a force occurring between the surfaces of solid and liquid phases of metals caused by different energy density of phonons of these phases. It explains abrupt changes in geometry and thermodynamic parameters at a melting point. "The Casimir force analogue" helps to estimate latent melting heat and to gain an insight into a solid-liquid transition problem.

Use of the 2-chlorotrityl chloride resin for microwave-assisted solid phase peptide synthesis.

PubMed

Ieronymaki, Matthaia; Androutsou, Maria Eleni; Pantelia, Anna; Friligou, Irene; Crisp, Molly; High, Kirsty; Penkman, Kirsty; Gatos, Dimitrios; Tselios, Theodore

2015-09-01

A fast and efficient microwave (MW)-assisted solid-phase peptide synthesis protocol using the 2-chlorotrityl chloride resin and the Fmoc/tBu methodology, has been developed. The established protocol combines the advantages of MW irradiation and the acid labile 2-chlorotrityl chloride resin. The effect of temperature during the MW irradiation, the degree of resin substitution during the coupling of the first amino acids and the rate of racemization for each amino acid were evaluated. The suggested solid phase methodology is applicable for orthogonal peptide synthesis and for the synthesis of cyclic peptides. © 2015 Wiley Periodicals, Inc.

Enjeux de fin de vie dans les cas de démence avancée

PubMed Central

Arcand, Marcel

2015-01-01

Résumé Objectif Répondre aux questions souvent posées sur la prise en charge de la pneumonie en phase terminale, de l’apport nutritionnel insuffisant et de la déshydratation dans les cas de démence avancée. Sources des données Une recherche a été effectuée dans MEDLINE sur Ovid pour des articles pertinents publiés jusqu’en février 2015. Aucune étude de niveau I n’a été relevée; la plupart des articles fournissaient des preuves de niveaux III. Les suggestions en matière de prise en charge des symptômes s’appuient en partie sur une récente participation à une approche Delphi visant à concevoir une directive pour le soulagement optimal des symptômes chez les patients atteints de pneumonie et de démence. Message principal Les sondes d’alimentation ne sont pas recommandés chez les patients atteints de démence terminale. L’alimentation de confort manuelle est préférable. L’hydratation parentérale pourrait être utile, mais elle peut aussi contribuer à l’inconfort à la fin de la vie. Si les soins buccaux sont adéquats, l’abstention ou la cessation de l’alimentation et de l’hydratation artificielles ne sont généralement pas associées à des manifestations d’inconfort. Puisque la pneumonie est habituellement très inconfortable, les cliniciens doivent être attentifs à la maîtrise des symptômes. La sédation pour maîtriser l’agitation est souvent utile chez les patients atteints de démence terminale. Conclusion Les soins à visée symptomatique sont une option appropriée pour les manifestations terminales de la démence avancée. Les lignes directrices de prise en charge des symptômes proposées s’appuient sur une revue de la littérature et sur un consensus d’experts.

NASA satellite communications application research. Phase 2: Efficient high power, solid state amplifier for EFH communications

NASA Technical Reports Server (NTRS)

Benet, James

1993-01-01

The final report describes the work performed from 9 Jun. 1992 to 31 Jul. 1993 on the NASA Satellite Communications Application Research (SCAR) Phase 2 program, Efficient High Power, Solid State Amplifier for EHF Communications. The purpose of the program was to demonstrate the feasibility of high-efficiency, high-power, EHF solid state amplifiers that are smaller, lighter, more efficient, and less costly than existing traveling wave tube (TWT) amplifiers by combining the output power from up to several hundred solid state amplifiers using a unique orthomode spatial power combiner (OSPC).

Lab-scale investigation on remediation of diesel-contaminated aquifer using microwave energy.

PubMed

Falciglia, Pietro P; Maddalena, Riccardo; Mancuso, Giuseppe; Messina, Valeria; Vagliasindi, Federico G A

2016-02-01

Aquifer contamination with diesel fuel is a worldwide environmental problem, and related available remediation technologies may not be adequately efficient, especially for the simultaneous treatment of both solid and water phases. In this paper, a lab-scale 2.45 GHz microwave (MW) treatment of an artificially diesel-contaminated aquifer was applied to investigate the effects of operating power (160, 350 and 500 W) and time on temperature profiles and contaminant removal from both solid and water phases. Results suggest that in diesel-contaminated aquifer MW remediation, power significantly influences the final reachable temperature and, consequently, contaminant removal kinetics. A maximum temperature of about 120 °C was reached at 500 W. Observed temperature values depended on the simultaneous irradiation of both aquifer grains and groundwater. In this case, solid phase heating is limited by the maximum temperature that interstitial water can reach before evaporation. A minimal residual diesel concentration of about 100 mg kg(-1) or 100 mg L(-1) was achieved by applying a power of 500 W for a time of 60 min for the solid or water phase, respectively. Measured residual TPH fractions showed that MW heating resulted in preferential effects of the removal of different TPH molecular weight fractions and that the evaporation-stripping phenomena plays a major role in final contaminant removal processes. The power low kinetic equation shows an excellent fit (r(2) > 0.993) with the solid phase residual concentration observed for all the powers investigated. A maximum diesel removal of 88 or 80% was observed for the MW treatment of the solid or water phase, respectively, highlighting the possibility to successfully and simultaneously remediate both the aquifer phases. Consequently, MW, compared to other biological or chemical-physical treatments, appears to be a better choice for the fast remediation of diesel-contaminated aquifers. Copyright © 2015 Elsevier Ltd. All rights reserved.

A unified analysis of solidification in Bridgman crystal growth

NASA Astrophysics Data System (ADS)

Lu, Ming-Fang

2012-04-01

The simulation of multiphase solidification process can be handled by combining the VOF (Volume of Fluid) transport equation, in which the continuum mechanics model is used to simulate the melt/solid interface and the conservation of mass, momentum, and energy. Because the melt phase, the solid phase, and the melt/solid interface are controlled by a single control equation; if the enthalpy model based on porosity concept represents the processing of the phase transformation range, it is possible to solve the problem of phase transformation in the same way as solving the single-phase problem. Once the energy field of enthalpy for each step in time is resolved, the position of the interface can be precisely calculated with the use of VOF equation. This type of novel VOF method can be applied to find out the conditions of vertical Bridgman crystal growing located on the earth or under microgravity.

A unified analysis of solidification in Bridgman crystal growth

NASA Astrophysics Data System (ADS)

Lu, Ming-Fang

2011-11-01

The simulation of multiphase solidification process can be handled by combining the VOF (Volume of Fluid) transport equation, in which the continuum mechanics model is used to simulate the melt/solid interface and the conservation of mass, momentum, and energy. Because the melt phase, the solid phase, and the melt/solid interface are controlled by a single control equation; if the enthalpy model based on porosity concept represents the processing of the phase transformation range, it is possible to solve the problem of phase transformation in the same way as solving the single-phase problem. Once the energy field of enthalpy for each step in time is resolved, the position of the interface can be precisely calculated with the use of VOF equation. This type of novel VOF method can be applied to find out the conditions of vertical Bridgman crystal growing located on the earth or under microgravity.

Developpement et validation d'un outil base sur l'acoustique geometrique pour le diagnostic du bruit de nacelle

NASA Astrophysics Data System (ADS)

Minard, Benoit

De nos jours, la problématique du bruit généré par les avions est devenue un point de développement important dans le domaine de l'aéronautique. C'est ainsi que de nombreuses études sont faites dans le domaine et une première approche consiste à modéliser de façon numérique ce bruit de manière à réduire de façon conséquente les coûts lors de la conception. C'est dans ce contexte qu'un motoriste a demandé à l'université de Sherbrooke, et plus particulièrement au groupe d'acoustique de l'Université de Sherbrooke (GAUS), de développer un outil de calcul de la propagation des ondes acoustiques dans les nacelles mais aussi pour l'étude des effets d'installation. Cet outil de prédiction leur permet de réaliser des études afin d'optimiser les traitements acoustiques (« liners »), la géométrie de ces nacelles pour des études portant sur l'intérieur de la nacelle et des études de positionnement des moteurs et de design pour les effets d'installation. L'objectif de ce projet de maîtrise était donc de poursuivre le travail réalisé par [gousset, 2011] sur l'utilisation d'une méthode de lancer de rayons pour l'étude des effets d'installation des moteurs d'avion. L'amélioration du code, sa rapidité, sa fiabilité et sa généralité étaient les objectifs principaux. Le code peut être utilisé avec des traitements acoustiques de surfaces («liners») et peut prendre en compte le phénomène de la diffraction par les arêtes et enfin peut être utilisé pour réaliser des études dans des environnements complexes tels que les nacelles d'avion. Le code développé fonctionne en 3D et procéde en 3 étapes : (1) Calcul des faisceaux initiaux (division d'une sphère, demi-sphère, maillage des surfaces de la géométrie) (2) Propagation des faisceaux dans l'environnement d'étude : calcul de toutes les caractéristiques des rayons convergents (amplitude, phase, nombre de réflexions, ...) (3) Reconstruction du champ de pression en un ou plusieurs points de l'espace à partir de rayons convergents (sommation des contributions de chaque rayon) : sommation cohérente. Le code (GA3DP) permet de prendre en compte les traitements de surface des parois, la directivité de la source, l'atténuation atmosphérique et la diffraction d'ordre 1. Le code a été validé en utilisant différentes méthodes telles que la méthode des sources-images, la méthode d'analyse modale ou encore la méthode des éléments finis de frontière. Un module Matlab a été créé spécialement pour l'étude des effets d'installation et intégré au code existant chez Pratt & Whitney Canada. Mots-clés : Acoustique géométrique - Ray-Tracing - Lancer de faisceaux - Diffraction - Sommation Cohérente - Niveau de Pression.

SOLID PHASE MICROEXTRACTION FOR TRACE LEVEL ANALYSIS OF DISINFECTION BY-PRODUCTS

EPA Science Inventory

This presentation focuses on the development of a solid-phase microextraction (SPME)-gas chromatography (GC)/ion trap mass spectrometry (MS) method for the analysis of semivolatile disinfection by-products (DBPs) in drinking water in the low ug/L range. These DBPs were selected ...

SEQUENTIAL EXTRACTIONS FOR PARTITIONING OF ARSENIC ON HYDROUS IRON OXIDES AND IRON SULFIDES

EPA Science Inventory

The objective of this study was to use model solids to test solutions designed to extract arsenic from relatively labile solid phase fractions. The use of sequential extractions provides analytical constraints on the identification of mineral phases that control arsenic mobility...

High-rate anaerobic treatment system for solid/lipid-rich wastewater using anaerobic baffled reactor with scum recovery.

PubMed

Fujihira, Takuya; Seo, Shogo; Yamaguchi, Takashi; Hatamoto, Masashi; Tanikawa, Daisuke

2018-04-27

A laboratory scale experiment was conducted to investigate the treatment of solid/lipid-rich wastewater with an anaerobic baffled reactor (ABR) and a down-flow hanging sponge (DHS) reactor. In this study, experimental periods were divided into three phases to explore efficient treatment of solids and lipids in wastewater. In ABR, >90% of the influent chemical oxygen demand (COD) was removed and >70% of the removed COD was converted to methane under steady-state conditions during each phase. During this period, >4.5 kg COD m -3  d -1 was achieved on an average in Phases 1 and 3. Biogas contributed to scum formation, and the scum was categorized into lipid-rich and sludge-containing types, which have energy potentials of 53.4 and 212 kcal/kg-wet weight, respectively. Therefore, by recovering solids and lipids, which formed persistent scum, ABR can be applied as a high-rate treatment for solid/lipid-rich wastewater. Copyright © 2018 Elsevier Ltd. All rights reserved.

Stabilizing Superionic-Conducting Structures via Mixed-Anion Solid Solutions of Monocarba- closo -borate Salts

DOE PAGES

Tang, Wan Si; Yoshida, Koji; Soloninin, Alexei V.; ...

2016-09-01

Solid lithium and sodium closo-polyborate-based salts are capable of superionic conductivities surpassing even liquid electrolytes, but often only at above-ambient temperatures where their entropically driven disordered phases become stabilized. Here we show by X-ray diffraction, quasielastic neutron scattering, differential scanning calorimetry, NMR, and AC impedance measurements that by introducing 'geometric frustration' via the mixing of two different closo-polyborate anions, namely, 1-CB 9H 10- and CB 11H 12-, to form solid-solution anion-alloy salts of lithium or sodium, we can successfully suppress the formation of possible ordered phases in favor of disordered, fast-ion-conducting alloy phases over a broad temperature range from subambientmore » to high temperatures. Finally, this result exemplifies an important advancement for further improving on the remarkable conductive properties generally displayed by this class of materials and represents a practical strategy for creating tailored, ambient-temperature, solid, superionic conductors for a variety of upcoming all-solid-state energy devices of the future.« less

Investigation of phase diagrams and physical stability of drug-polymer solid dispersions.

PubMed

Lu, Jiannan; Shah, Sejal; Jo, Seongbong; Majumdar, Soumyajit; Gryczke, Andreas; Kolter, Karl; Langley, Nigel; Repka, Michael A

2015-01-01

Solid dispersion technology has been widely explored to improve the solubility and bioavailability of poorly water-soluble compounds. One of the critical drawbacks associated with this technology is the lack of physical stability, i.e. the solid dispersion would undergo recrystallization or phase separation thus limiting a product's shelf life. In the current study, the melting point depression method was utilized to construct a complete phase diagram for felodipine (FEL)-Soluplus® (SOL) and ketoconazole (KTZ)-Soluplus® (SOL) binary systems, respectively, based on the Flory-Huggins theory. The miscibility or solubility of the two compounds in SOL was also determined. The Flory-Huggins interaction parameter χ values of both systems were calculated as positive at room temperature (25 °C), indicating either compound was miscible with SOL. In addition, the glass transition temperatures of both solid dispersion systems were theoretically predicted using three empirical equations and compared with the practical values. Furthermore, the FEL-SOL solid dispersions were subjected to accelerated stability studies for up to 3 months.

Rate-dependent, Li-ion insertion/deinsertion behavior of LiFePO4 cathodes in commercial 18650 LiFePO4 cells.

PubMed

Liu, Qi; He, Hao; Li, Zhe-Fei; Liu, Yadong; Ren, Yang; Lu, Wenquan; Lu, Jun; Stach, Eric A; Xie, Jian

2014-03-12

We have performed operando synchrotron high-energy X-ray diffraction (XRD) to obtain nonintrusive, real-time monitoring of the dynamic chemical and structural changes in commercial 18650 LiFePO4/C cells under realistic cycling conditions. The results indicate a nonequilibrium lithium insertion and extraction in the LiFePO4 cathode, with neither the LiFePO4 phase nor the FePO4 phase maintaining a static composition during lithium insertion/extraction. On the basis of our observations, we propose that the LiFePO4 cathode simultaneously experiences both a two-phase reaction mechanism and a dual-phase solid-solution reaction mechanism over the entire range of the flat voltage plateau, with this dual-phase solid-solution behavior being strongly dependent on charge/discharge rates. The proposed dual-phase solid-solution mechanism may explain the remarkable rate capability of LiFePO4 in commercial cells.

A parametric analysis of waves propagating in a porous solid saturated by a three-phase fluid.

PubMed

Santos, Juan E; Savioli, Gabriela B

2015-11-01

This paper presents an analysis of a model for the propagation of waves in a poroelastic solid saturated by a three-phase viscous, compressible fluid. The constitutive relations and the equations of motion are stated first. Then a plane wave analysis determines the phase velocities and attenuation coefficients of the four compressional waves and one shear wave that propagate in this type of medium. A procedure to compute the elastic constants in the constitutive relations is defined next. Assuming the knowledge of the shear modulus of the dry matrix, the other elastic constants in the stress-strain relations are determined by employing ideal gedanken experiments generalizing those of Biot's theory for single-phase fluids. These experiments yield expressions for the elastic constants in terms of the properties of the individual solid and fluids phases. Finally the phase velocities and attenuation coefficients of all waves are computed for a sample of Berea sandstone saturated by oil, gas, and water.

Further analytical study of hybrid rocket combustion

NASA Technical Reports Server (NTRS)

Hung, W. S. Y.; Chen, C. S.; Haviland, J. K.

1972-01-01

Analytical studies of the transient and steady-state combustion processes in a hybrid rocket system are discussed. The particular system chosen consists of a gaseous oxidizer flowing within a tube of solid fuel, resulting in a heterogeneous combustion. Finite rate chemical kinetics with appropriate reaction mechanisms were incorporated in the model. A temperature dependent Arrhenius type fuel surface regression rate equation was chosen for the current study. The governing mathematical equations employed for the reacting gas phase and for the solid phase are the general, two-dimensional, time-dependent conservation equations in a cylindrical coordinate system. Keeping the simplifying assumptions to a minimum, these basic equations were programmed for numerical computation, using two implicit finite-difference schemes, the Lax-Wendroff scheme for the gas phase, and, the Crank-Nicolson scheme for the solid phase.

Self-consistent phonon theory of the crystallization and elasticity of attractive hard spheres.

PubMed

Shin, Homin; Schweizer, Kenneth S

2013-02-28

We propose an Einstein-solid, self-consistent phonon theory for the crystal phase of hard spheres that interact via short-range attractions. The approach is first tested against the known behavior of hard spheres, and then applied to homogeneous particles that interact via short-range square well attractions and the Baxter adhesive hard sphere model. Given the crystal symmetry, packing fraction, and strength and range of attractive interactions, an effective harmonic potential experienced by a particle confined to its Wigner-Seitz cell and corresponding mean square vibrational amplitude are self-consistently calculated. The crystal free energy is then computed and, using separate information about the fluid phase free energy, phase diagrams constructed, including a first-order solid-solid phase transition and its associated critical point. The simple theory qualitatively captures all the many distinctive features of the phase diagram (critical and triple point, crystal-fluid re-entrancy, low-density coexistence curve) as a function of attraction range, and overall is in good semi-quantitative agreement with simulation. Knowledge of the particle localization length allows the crystal shear modulus to be estimated based on elementary ideas. Excellent predictions are obtained for the hard sphere crystal. Expanded and condensed face-centered cubic crystals are found to have qualitatively different elastic responses to varying attraction strength or temperature. As temperature increases, the expanded entropic solid stiffens, while the energy-controlled, fully-bonded dense solid softens.

Efficient chemical potential evaluation with kinetic Monte Carlo method and non-uniform external potential: Lennard-Jones fluid, liquid, and solid

NASA Astrophysics Data System (ADS)

Ustinov, E. A.

2017-07-01

The aim of this paper is to present a method of a direct evaluation of the chemical potential of fluid, liquid, and solid with kinetic Monte Carlo simulation. The method is illustrated with the 12-6 Lennard-Jones (LJ) system over a wide range of density and temperature. A distinctive feature of the methodology used in the present study is imposing an external potential on the elongated simulation box to split the system into two equilibrium phases, one of which is substantially diluted. This technique provides a reliable direct evaluation of the chemical potential of the whole non-uniform system (including that of the uniformly distributed dense phase in the central zone of the box), which, for example, is impossible in simulation of the uniform crystalline phase. The parameters of the vapor-liquid, liquid-solid, and fluid-solid transitions have been reliably determined. The chemical potential and the pressure are defined as thermodynamically consistent functions of density and temperature separately for the liquid and the solid (FCC) phases. It has been shown that in two-phase systems separated by a flat interface, the crystal melting always occurs at equilibrium conditions. It is also proved that in the limit of zero temperature, the specific heat capacity of an LJ crystal at constant volume is exactly 3Rg (where Rg is the gas constant) without resorting to harmonic oscillators.

Buckling failure of square ice-nanotube arrays constrained in graphene nanocapillaries.

PubMed

Zhu, YinBo; Wang, FengChao; Wu, HengAn

2016-08-07

Graphene confinement provides a new physical and mechanical environment with ultrahigh van der Waals pressure, resulting in new quasi-two-dimensional phases of few-layer ice. Polymorphic transition can occur in bilayer constrained water/ice system. Here, we perform a comprehensive study of the phase transition of AA-stacked bilayer water constrained within a graphene nanocapillary. The compression-limit and superheating-limit (phase) diagrams are obtained, based on the extensive molecular-dynamics simulations at numerous thermodynamic states. Liquid-to-solid, solid-to-solid, and solid-to-liquid-to-solid phase transitions are observed in the compression and superheating of bilayer water. Interestingly, there is a temperature threshold (∼275 K) in the compression-limit diagram, which indicates that the first-order and continuous-like phase transitions of bilayer water depend on the temperature. Two obviously different physical processes, compression and superheating, display similar structural evolution; that is, square ice-nanotube arrays (BL-VHDI) will bend first and then transform into bilayer triangular AA stacking ice (BL-AAI). The superheating limit of BL-VHDI exhibits local maxima, while that of BL-AAI increases monotonically. More importantly, from a mechanics point of view, we propose a novel mechanism of the transformation from BL-VHDI to BL-AAI, both for the compression and superheating limits. This structural transformation can be regarded as the "buckling failure" of the square-ice-nanotube columns, which is dominated by the lateral pressure.

Mycoestrogen determination in cow milk: Magnetic solid-phase extraction followed by liquid chromatography and tandem mass spectrometry analysis.

PubMed

Capriotti, Anna Laura; Cavaliere, Chiara; Foglia, Patrizia; La Barbera, Giorgia; Samperi, Roberto; Ventura, Salvatore; Laganà, Aldo

2016-12-01

Recently, magnetic solid-phase extraction has gained interest because it presents various operational advantages over classical solid-phase extraction. Furthermore, magnetic nanoparticles are easy to prepare, and various materials can be used in their synthesis. In the literature, there are only few studies on the determination of mycoestrogens in milk, although their carryover in milk has occurred. In this work, we wanted to develop the first (to the best of our knowledge) magnetic solid-phase extraction protocol for six mycoestrogens from milk, followed by liquid chromatography and tandem mass spectrometry analysis. Magnetic graphitized carbon black was chosen as the adsorbent, as this carbonaceous material, which is very different from the most diffuse graphene and carbon nanotubes, had already shown selectivity towards estrogenic compounds in milk. The graphitized carbon black was decorated with Fe 3 O 4 , which was confirmed by the characterization analyses. A milk deproteinization step was avoided, using only a suitable dilution in phosphate buffer as sample pretreatment. The overall process efficiency ranged between 52 and 102%, whereas the matrix effect considered as signal suppression was below 33% for all the analytes even at the lowest spiking level. The obtained method limits of quantification were below those of other published methods that employ classical solid-phase extraction protocols. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Microwave assisted solid phase extraction for separation preconcentration sulfamethoxazole in wastewater using tyre based activated carbon as solid phase material prior to spectrophotometric determination.

PubMed

Mogolodi Dimpe, K; Mpupa, Anele; Nomngongo, Philiswa N

2018-01-05

This work was chiefly encouraged by the continuous consumption of antibiotics which eventually pose harmful effects on animals and human beings when present in water systems. In this study, the activated carbon (AC) was used as a solid phase material for the removal of sulfamethoxazole (SMX) in wastewater samples. The microwave assisted solid phase extraction (MASPE) as a sample extraction method was employed to better extract SMX in water samples and finally the analysis of SMX was done by the UV-Vis spectrophotometer. The microwave assisted solid phase extraction method was optimized using a two-level fractional factorial design by evaluating parameters such as pH, mass of adsorbent (MA), extraction time (ET), eluent ratio (ER) and microwave power (MP). Under optimized conditions, the limit of detection (LOD) and limit of quantification (LOQ) were 0.5μgL -1 and 1.7μgL -1 , respectively, and intraday and interday precision expressed in terms of relative standard deviation were >6%.The maximum adsorption capacity was 138mgg -1 for SMX and the adsorbent could be reused eight times. Lastly, the MASPE method was applied for the removal of SMX in wastewater samples collected from a domestic wastewater treatment plant (WWTP) and river water. Copyright © 2017 Elsevier B.V. All rights reserved.

Molecularly imprinted polymer/cryogel composites for solid-phase extraction of bisphenol A from river water and wine.

PubMed

Baggiani, Claudio; Baravalle, Patrizia; Giovannoli, Cristina; Anfossi, Laura; Giraudi, Gianfranco

2010-05-01

Superporous monolithic hydrogels (cryogel monoliths) are elastic, sponge-like materials that can be prepared in an aqueous medium through a cryotropic gelation technique. These monoliths show interesting properties for the development of high-throughput solid-phase extraction supports to treat large volumes of aqueous samples. In this work, a cryogel-supported molecularly imprinted solid-phase extraction approach for the endocrine disruptor bisphenol A (BPA) from river water and wine samples is presented. An imprinted polymer with molecular recognition properties for BPA was prepared in acetonitrile by thermal polymerization of a mixture of 4,4'-dihydroxy-2,2-diphenyl-1,1,1,3,3,3-trifluoropropane as a mimic template of BPA, 4-vinylpyridine and trimethylolpropane trimethacrylate in a molar ratio of 1 + 6 + 6. Fine imprinted particles (<10 microm) were embedded in a poly-acrylamide-co-N,N'-methylenbisacrylamide cryogel obtained by ammonium persulfate-induced cryopolymerization at -18 degrees C. The resulting monolithic gel was evaluated for its use as a sorbent support in an off-line solid-phase extraction approach to recover BPA from dilute aqueous samples with minimum pre-loading work-up. The optimized extraction protocol resulted in a reliable MISPE method suitable to selectively extract and preconcentrate BPA from river water and red wine samples, demonstrating the practical feasibility of cryogel-trapped imprinted polymers as solid-phase extraction materials.

8. INTERIOR VIEW, LOOKING WEST, WITH GREY IRON HOLDING FURNACES ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. INTERIOR VIEW, LOOKING WEST, WITH GREY IRON HOLDING FURNACES AND AN IRON POUR IN PROCESS, CUPOLA TENDER RICHARD SLAUGHTER SUPERVISING THE POUR. MOLTEN DUCTILE IRON IS POURED FROM THIS 25-TON HOLDING FURNACE INTO LADLES FOR TRANSPORT TO CASTING STATIONS. - Stockham Pipe & Fittings Company, Grey Iron Foundry, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

40 CFR 464.35 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year. PSES Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average kg/1,000 kkg (pounds per million pounds) of metal poured Copper (T) 0.0129 0.0071...

The solid-solution region for the langasite-type Ca3TaGa3Si2O14 crystal as determined by a lever rule

NASA Astrophysics Data System (ADS)

Zhao, Hengyu; Uda, Satoshi; Maeda, Kensaku; Nozawa, Jun; Koizumi, Haruhiko; Fujiwara, Kozo

2015-04-01

A lever rule was applied to data concerning the compositions and proportions of secondary phases coexisting with a Ca3TaGa3Si2O14 (CTGS) matrix to determine the boundary compositions of the solid-solution region for CTGS at 1320 °C, as a means of ascertaining the solid-solution for the langasite-type phase in the quaternary CaO-Ta2O5-Ga2O3-SiO2 system. The compositions and proportions of secondary phases were assessed by electron probe micro-analysis as well as through back-scattered electron images. The experimental results showed that the narrow solid-solution region for CTGS is located in a Ta-poor, Ga-poor and Si-rich region relative to its stoichiometric composition.

Ultrasonic semi-solid coating soldering 6061 aluminum alloys with Sn-Pb-Zn alloys.

PubMed

Yu, Xin-ye; Xing, Wen-qing; Ding, Min

2016-07-01

In this paper, 6061 aluminum alloys were soldered without a flux by the ultrasonic semi-solid coating soldering at a low temperature. According to the analyses, it could be obtained that the following results. The effect of ultrasound on the coating which promoted processes of metallurgical reaction between the components of the solder and 6061 aluminum alloys due to the thermal effect. Al2Zn3 was obtained near the interface. When the solder was in semi-solid state, the connection was completed. Ultimately, the interlayer mainly composed of three kinds of microstructure zones: α-Pb solid solution phases, β-Sn phases and Sn-Pb eutectic phases. The strength of the joints was improved significantly with the minimum shear strength approaching 101MPa. Copyright © 2016. Published by Elsevier B.V.

Microwave spectroscopic observation of multiple phase transitions in the bilayer electron solid in wide quantum wells

NASA Astrophysics Data System (ADS)

Hatke, Anthony; Engel, Lloyd; Liu, Yang; Shayegan, Mansour; Pfeiffer, Loren; West, Ken; Baldwin, Kirk

2015-03-01

The termination of the low Landau filling factor (ν) fractional quantum Hall series for a single layer two dimensional system results in the formation of a pinned Wigner solid for ν < 1 / 5. In a wide quantum well the system can support a bilayer state in which interlayer and intralayer interactions become comparable, which is measured in traditional transport as an insulating state for ν < 1 / 2. We perform microwave spectroscopic studies of this bilayer state and observe that this insulator exhibits a resonance, a signature of a solid phase. Additionally, we find that as we increase the density of the well at fixed ν this bilayer solid exhibits multiple sharp reductions in the resonance amplitude vs ν. This behavior is characteristic of multiple phase transitions, which remain hidden from dc transport measurements.

Stability and Solid Solutions of Hydrous Alumino-Silicates in the Earth's Mantle

NASA Astrophysics Data System (ADS)

Panero, W. R.; Caracas, R.

2017-12-01

The degree to which the Earth's mantle stores and cycles water in excess of the storage capacity of nominally anhydrous minerals is dependent upon the stability of hydrous phases under mantle-relevant pressures, temperatures, and compositions. Two hydrous phases, phase D and phase H are stable to the pressures and temperatures of the Earth's lower mantle, suggesting that the Earth's lower mantle may participate in the cycling of water. Each phase has a wide solid solution series between MgSi2O6H2-Al2SiO6H2 and MgSiO4H2-2δAlOOH-SiO2, respectively, yet most work addresses end-member compositions for analysis of stability and elastic properties. We present the results of density functional theory calculations on the stability, structure, bonding, partitioning, and elasticity of hydrous phases D and H in the Al2O3-SiO2-MgO-H2O system, addressing the solid solution series through a statistical sampling of site occupancy and calculation of the partition function from the grand canonical ensemble. We find that the addition of Al to the endmember compositions stabilizes each phase to higher temperatures through additional configurational entropy. We further find that solid solutions tend not to undergo hydrogen-bond symmetrization as is found in the end member compositions as a result of non-symmetric bonding environments.

Improved Heat-of-Fusion Energy Storage

NASA Technical Reports Server (NTRS)

Chen, K. H.; Manvi, R.

1982-01-01

Alkali metal/alkali-halide mixtures proposed for preventing solid buildup during energy recovery. When mixture melts (by absorption of heat of fusion), it forms two immiscible liquids. Salt-rich phase is heavier and has higher melting/recrysallization temperature; so during energy recovery salt crystallizes in this phase first. Since heat exchanger for energy recovery is in lighter metal-rich phase, solids do not form and there is no reduction of heat-recovery efficiency.

Solid phase graft copolymerization of acrylic monomers onto thermoplastics and their use as blend compatibilizers

NASA Astrophysics Data System (ADS)

Subramanian, Srinivas

This research work is an extension of some of the earlier work done on the development of solid phase grafting technique to graft various monomers onto polymers as well as postulation of the usefulness of the graft copolymers thus synthesized. Polystyrene grafted with acrylic acid, previously developed in bench scale, was synthesized in pilot-plant scale batches. Process parameter studies on the grafting of acrylic acid onto polypropylene and developmental studies on the grafting of maleic anhydride onto polystyrene were also done. Polymers grafted with polar molecules such as maleic anhydride and acrylic acid have been used to compatibilize immiscible blends of polar and non-polar polymers. On the same note, the applicability of the solid phase graft copolymers as blend compatibilizers were investigated and their performance was compared to commercially available compatibilizers. Solid phase graft copolymerization process is a technique to synthesize graft copolymers. Some of its salient features are use of minimal solvent to conduct the reaction and easy equipment modification. It is a low pressure and low temperature process. This technique provides a viable alternative to the environmentally hazardous, and time consuming conventional process currently in use. Hence, development of this technique could be beneficial not only to the plastics industry, but also to mankind. Also, this technique provides a low-cost and extremely easy method to develop graft copolymers such as acrylic acid functionalized polymers that are rapidly gaining popularity as blend compatibilizers and polymer reinforcing agents. A study that proves the potential of these solid phase graft copolymers as good blend compatibilizers for industrially important immiscible polymers will develop interest in the industries about this grafting process. The free radical solid phase graft copolymerization process was carried in a modified Brabender-type mixer fitted with specially designed blades to promote efficient mixing of the polymer, initiator, monomer, and solvent. The grafting was qualitatively confirmed by means of a FTIR and quantitatively using titration. The polymer blends were synthesized in a single screw extruder. Rheological, morphological, thermal, mechanical, and molecular weight studies were done on these blends. The graft copolymers produced in larger batches had the same amount of graft content as those produced in smaller batches. This small success is a positive step towards the goal of commercializing this process. Grafting of acrylic acid onto polypropylene gave graft levels of 4 weight percent. However, the attempt to graft maleic anhydride onto polystyrene was not successful. The solid phase graft copolymers were successfully able to compatibilize the polymer blend systems studied (PS/PMMA, PS/nylon 6,6, PS/nylon 6, and PP/nylon 6). The properties of the blends compatibilized using the solid phase graft copolymers were comparable to and in some instances, better than those of the blends compatibilized with commercially available graft copolymers. The successful scale-up of the process, development of new graft copolymers and ability of copolymers to compatibilize blends augurs well for the solid phase grafting process.

Non-Abelian Geometric Phases Carried by the Quantum Noise Matrix

NASA Astrophysics Data System (ADS)

Bharath, H. M.; Boguslawski, Matthew; Barrios, Maryrose; Chapman, Michael

2017-04-01

Topological phases of matter are characterized by topological order parameters that are built using Berry's geometric phase. Berry's phase is the geometric information stored in the overall phase of a quantum state. We show that geometric information is also stored in the second and higher order spin moments of a quantum spin system, captured by a non-abelian geometric phase. The quantum state of a spin-S system is uniquely characterized by its spin moments up to order 2S. The first-order spin moment is the spin vector, and the second-order spin moment represents the spin fluctuation tensor, i.e., the quantum noise matrix. When the spin vector is transported along a loop in the Bloch ball, we show that the quantum noise matrix picks up a geometric phase. Considering spin-1 systems, we formulate this geometric phase as an SO(3) operator. Geometric phases are usually interpreted in terms of the solid angle subtended by the loop at the center. However, solid angles are not well defined for loops that pass through the center. Here, we introduce a generalized solid angle which is well defined for all loops inside the Bloch ball, in terms of which, we interpret the SO(3) geometric phase. This geometric phase can be used to characterize topological spin textures in cold atomic clouds.

Etude de la transmission sonore a travers un protecteur de type "coquilles" : modelisation numerique et validation experimentale

NASA Astrophysics Data System (ADS)

Boyer, Sylvain

On estime que sur les 3,7 millions des travailleurs au Quebec, plus de 500 000 sont exposes quotidiennement a des niveaux de bruits pouvant causer des lesions de l'appareil auditif. Lorsqu'il n'est pas possible de diminuer le niveau de bruit environnant, en modifiant les sources de bruits, ou en limitant la propagation du son, le port de protecteurs auditifs individualises, telles que les coquilles, demeure l'ultime solution. Bien que vue comme une solution a court terme, elle est communement employee, du fait de son caractere peu dispendieux, de sa facilite d'implantation et de son adaptabilite a la plupart des operations en environnement bruyant. Cependant les protecteurs auditifs peuvent etre a la fois inadaptes aux travailleurs et a leur environnement et inconfortables ce qui limite leur temps de port, reduisant leur protection effective. Afin de palier a ces difficultes, un projet de recherche sur la protection auditive intitule : " Developpement d'outils et de methodes pour ameliorer et mieux evaluer la protection auditive individuelle des travailleur ", a ete mis sur pied en 2010, associant l'Ecole de technologie superieure (ETS) et l'Institut de recherche Robert-Sauve en sante et en securite du travail (IRSST). S'inscrivant dans ce programme de recherche, le present travail de doctorat s'interesse specifiquement a la protection auditive au moyen de protecteurs auditifs " passifs " de type coquille, dont l'usage presente trois problematiques specifiques presentees dans les paragraphes suivants. La premiere problematique specifique concerne l'inconfort cause par exemple par la pression statique induite par la force de serrage de l'arceau, qui peut reduire le temps de port recommande pour limiter l'exposition au bruit. Il convient alors de pouvoir donner a l'utilisateur un protecteur confortable, adapte a son environnement de travail et a son activite. La seconde problematique specifique est l'evaluation de la protection reelle apportee par le protecteur. La methode des seuils auditifs REAT (Real Ear Attenuation Threshold) aussi vu comme un "golden standard" est utilise pour quantifier la reduction du bruit mais surestime generalement la performance des protecteurs. Les techniques de mesure terrains, telles que la F-MIRE (Field Measurement in Real Ear) peuvent etre a l'avenir de meilleurs outils pour evaluer l'attenuation individuelle. Si ces techniques existent pour des bouchons d'oreilles, elles doivent etre adaptees et ameliorees pour le cas des coquilles, en determinant l'emplacement optimal des capteurs acoustiques et les facteurs de compensation individuels qui lient la mesure microphonique a la mesure qui aurait ete prise au tympan. La troisieme problematique specifique est l'optimisation de l'attenuation des coquilles pour les adapter a l'individu et a son environnement de travail. En effet, le design des coquilles est generalement base sur des concepts empiriques et des methodes essais/erreurs sur des prototypes. La piste des outils predictifs a ete tres peu etudiee jusqu'a present et meriterait d'etre approfondie. L'utilisation du prototypage virtuel, permettrait a la fois d'optimiser le design avant production, d'accelerer la phase de developpement produit et d'en reduire les couts. L'objectif general de cette these est de repondre a ces differentes problematiques par le developpement d'un modele de l'attenuation sonore d'un protecteur auditif de type coquille. A cause de la complexite de la geometrie de ces protecteurs, la methode principale de modelisation retenue a priori est la methode des elements finis (FEM). Pour atteindre cet objectif general, trois objectifs specifiques ont ete etablis et sont presentes dans les trois paragraphes suivants. (Abstract shortened by ProQuest.).

Isostructural solid-solid phase transition in monolayers of soft core-shell particles at fluid interfaces: structure and mechanics.

PubMed

Rey, Marcel; Fernández-Rodríguez, Miguel Ángel; Steinacher, Mathias; Scheidegger, Laura; Geisel, Karen; Richtering, Walter; Squires, Todd M; Isa, Lucio

2016-04-21

We have studied the complete two-dimensional phase diagram of a core-shell microgel-laden fluid interface by synchronizing its compression with the deposition of the interfacial monolayer. Applying a new protocol, different positions on the substrate correspond to different values of the monolayer surface pressure and specific area. Analyzing the microstructure of the deposited monolayers, we discovered an isostructural solid-solid phase transition between two crystalline phases with the same hexagonal symmetry, but with two different lattice constants. The two phases corresponded to shell-shell and core-core inter-particle contacts, respectively; with increasing surface pressure the former mechanically failed enabling the particle cores to come into contact. In the phase-transition region, clusters of particles in core-core contacts nucleate, melting the surrounding shell-shell crystal, until the whole monolayer moves into the second phase. We furthermore measured the interfacial rheology of the monolayers as a function of the surface pressure using an interfacial microdisk rheometer. The interfaces always showed a strong elastic response, with a dip in the shear elastic modulus in correspondence with the melting of the shell-shell phase, followed by a steep increase upon the formation of a percolating network of the core-core contacts. These results demonstrate that the core-shell nature of the particles leads to a rich mechanical and structural behavior that can be externally tuned by compressing the interface, indicating new routes for applications, e.g. in surface patterning or emulsion stabilization.

Application of mercapto-silica polymerized high internal phase emulsions for the solid-phase extraction and preconcentration of trace lead(II).

PubMed

Su, Rihui; Ruan, Guihua; Chen, Zhengyi; Du, Fuyou; Li, Jianping

2015-12-01

A new class of solid-phase extraction column prepared with grafted mercapto-silica polymerized high internal phase emulsion particles was used for the preconcentration of trace lead. First, mercapto-silica polymerized high internal phase emulsion particles were synthesized by using high internal phase emulsion polymerization and carefully assembled in a polyethylene syringe column. The influences of various parameters including adsorption pH value, adsorption and desorption solvents, flow rate of the adsorption and desorption procedure were optimized, respectively, and the suitable uploading sample volumes, adsorption capacity, and reusability of solid phase extraction column were also investigated. Under the optimum conditions, Pb(2+) could be preconcentrated quantitatively over a wide pH range (2.0-5.0). In the presence of foreign ions, such as Na(+) , K(+) , Ca(2+) , Zn(2+) , Mg(2+) , Cu(2+) , Fe(2+) , Cd(2+) , Cl(-) and NO3 (-) , Pb(2+) could be recovered successfully. The prepared solid-phase extraction column performed with high stability and desirable durability, which allowed more than 100 replicate extractions without measurable changes of performance. The feasibility of the developed method was further validated by the extraction of Pb(2+) in rice samples. At three spiked levels of 40.0, 200 and 800 μg/kg, the average recoveries for Pb(2+) in rice samples ranged from 87.3 to 105.2%. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Two phase microstructure for Ag-Ni nanowires

NASA Astrophysics Data System (ADS)

Srivastava, Chandan; Rai, Rajesh Kumar

2013-03-01

In the present study, electrodeposition technique was used to produce Ag-Ni nanowires. Ag-Ni system shows extremely high bulk immiscibility. Nanowire morphology was achieved by employing an anodic alumina membrane having pores of ˜200 nm diameter. Microstructure of as-deposited wire was composed of nano-sized solid solution structured Ag-Ni nanoparticles embedded in a matrix of pure Ag phase. It is proposed that the two phase microstructure resulted from an initial formation of solid solution structured nanoparticles in the alumina template pore followed by nucleation of pure Ag phase over the particles which eventually grew to form the matrix phase.

Global distribution of secondary organic aerosol particle phase state

NASA Astrophysics Data System (ADS)

Shiraiwa, M.; Li, Y., Sr.; Tsimpidi, A.; Karydis, V.; Berkemeier, T.; Pandis, S. N.; Lelieveld, J.; Koop, T.; Poeschl, U.

2016-12-01

Secondary organic aerosols (SOA) account for a large fraction of submicron particles in the atmosphere and play a key role in aerosol effects on climate, air quality and public health. The formation and aging of SOA proceed through multiple steps of chemical reaction and mass transport in the gas and particle phases, which is challenging for the interpretation of field measurements and laboratory experiments as well as accurate representation of SOA evolution in atmospheric aerosol models. SOA particles can adopt liquid, semi-solid and amorphous solid (glassy) phase states depending on chemical composition, relative humidity and temperature. The particle phase state is crucial for various atmospheric gas-particle interactions, including SOA formation, heterogeneous and multiphase reactions and ice nucleation. We found that organic compounds with a wide variety of functional groups fall into molecular corridors, characterized by a tight inverse correlation between molar mass and volatility. Based on the concept of molecular corridors, we develop a method to estimate glass transition temperatures based on the molar mass and molecular O:C ratio of SOA components, which is a key property for determination of particle phase state. We use the global chemistry climate model EMAC with the organic aerosol module ORACLE to predict the atmospheric SOA phase state. For the planetary boundary layer, global simulations indicate that SOA is mostly liquid in tropical and polar air with high relative humidity, semi-solid in the mid-latitudes, and solid over dry lands. We find that in the middle and upper troposphere (>500 hPa) SOA should be mostly in a glassy solid phase state. Thus, slow diffusion of water, oxidants, and organic molecules could kinetically limit gas-particle interactions of SOA in the free and upper troposphere, promote ice nucleation and facilitate long-range transport of reactive and toxic organic pollutants embedded within SOA.

Assessing the Selectivity of Extractant Solutions for Recovering Labile Arsenic Associated with Iron (Hydr)oxides and Sulfides in Sediments

EPA Science Inventory

Sequential extractions can provide analytical constraints on the identification of mineral phases that control arsenic speciation in sediments. Model solids were used in this study to evaluate different solutions designed to extract arsenic from relatively labile solid phases. ...

Discovering Volatile Chemicals from Window Weatherstripping through Solid-Phase Microextraction/Gas Chromatography-Mass Spectrometry

ERIC Educational Resources Information Center

Rosu, Cornelia; Cueto, Rafael; Veillion, Lucas; David, Connie; Laine, Roger A.; Russo, Paul S.

2017-01-01

Volatile compounds from polymeric materials such as weatherstripping were identified by solid-phase microextraction (SPME), a solvent-free analytical method, coupled to gas chromatography-mass spectrometry (GC-MS). These compounds, originating from additives and fillers used in weatherstripping processing, were mostly polycyclic aromatic…

THE DISTRIBUTION, SOLID-PHASE SPECIATION, AND DESORPTION/DISSOLUTION OF AS IN IRON-BASED DRINKING WATER TREATMENT MEDIA 1

EPA Science Inventory

Arsenic concentrations (Total Recoverable As by EPA Method 3051, soluble, Toxicity Characteristic Leaching Procedure extractable) and solid-phase speciation (by X-ray Absorption Near-Edge Spectroscopy-XANES) were assessed as a function of depth through Fe-media beds for two comme...

Solid Phase Characterization of Tank 241-C-105 Grab Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ely, T. M.; LaMothe, M. E.; Lachut, J. S.

The solid phase characterization (SPC) of three grab samples from single-shell Tank 241-C-105 (C-105) that were received at the laboratory the week of October 26, 2015, has been completed. The three samples were received and broken down in the 11A hot cells.

Headspace analysis of polar organic compounds in biological matrixes using solid phase microextraction (SPME)

USDA-ARS?s Scientific Manuscript database

Analysis of biological fluids and waste material is difficult and tedious given the sample matrix. A rapid automated method for the determination of volatile fatty acids and phenolic and indole compounds was developed using a multipurpose sampler (MPS) with solid phase microextraction (SPME) and GC-...

COMPARISON OF TWO DIFFERENT SOLID PHASE EXTRACTION/LARGE VOLUME INJECTION PROCEDURES FOR METHOD 8270

EPA Science Inventory

Two solid phase (SPE) and one traditional continuous liquid-liquid extraction method are compared for analysis of Method 8270 SVOCs. Productivity parameters include data quality, sample volume, analysis time and solvent waste.

One SPE system, unique in the U.S., uses aut...

Experimental Method Development for Estimating Solid-phase Diffusion Coefficients and Material/Air Partition Coefficients of SVOCs

EPA Science Inventory

The solid-phase diffusion coefficient (Dm) and material-air partition coefficient (Kma) are key parameters for characterizing the sources and transport of semivolatile organic compounds (SVOCs) in the indoor environment. In this work, a new experimental method was developed to es...

THE DISTRIBUTION, SOLID-PHASE SPECIATION, AND DESORPTION/DISSOLUTION OF AS IN IRON-BASED TREATMENT MEDIA

EPA Science Inventory

Arsenic concentrations (Total Recoverable As by EPA Method 3051) and solid-phase speciation (by X-ray Absorption Near-Edge Spectroscopy-XANES) were assessed as a function of depth through Fe-media beds for two commercially available products from pilot-scale field tests. These re...

THE DISTRIBUTION, SOLID-PHASE SPECIATION, AND DESORPTION/DISSOLUTION OF AS IN IRON-BASED DRINKING WATER TREATMENT MEDIA - JOURNAL

EPA Science Inventory

Arsenic concentrations (Total Recoverable As by EPA Method 3051, soluble, Toxicity Characteristic Leaching Procedure extractable) and solid-phase speciation (by X-ray Absorption Near-Edge Spectroscopy-XANES) were assessed as a function of depth through Fe-media beds for two comme...

THE DISTRIBUTION AND SOLID-PHASE SPECIATION OF AS IN IRON-BASED TREATMENT MEDIA

EPA Science Inventory

Arsenic concentrations (Total Recoverable As by EPA Method 3051) and solid-phase speciation (by X-ray Absorption Near-Edge Spectroscopy-XANES) were assessed as a function of depth through Fe-media beds for two commercially available products from pilot-scale field tests. These r...

Determination of Plant Volatiles Using Solid Phase Microextraction GC-MS

ERIC Educational Resources Information Center

Van Bramer, Scott; Goodrich, Katherine R.

2015-01-01

This experiment combines analytical techniques of solid phase microextraction and gas chromatography-mass spectrometry with easily relatable and accessible plant volatile chemistry (floral and vegetative scents of local/available plants). The biosynthesis and structure of these chemicals are of interest in the areas of organic chemistry,…

A Discovery-Oriented Approach to Solid-Phase Peptide Synthesis

ERIC Educational Resources Information Center

Bockman, Matthew R.; Miedema, Christopher J.; Brennan, Brian B.

2012-01-01

In this discovery-oriented laboratory experiment, students use solid-phase synthesis techniques to construct a dipeptide containing an unknown amino acid. Following synthesis and cleavage from the polymeric support, electrospray ionization-mass spectrometry is employed to identify the unknown amino acid that was used in the peptide coupling. This…

Analysis of ecologically relevant pharmaceuticals in wastewater and surface water using selective solid phase extraction and UPLC/MS/MS

EPA Science Inventory

A rapid and sensitive method has been developed for the analysis of 48 human prescription active pharmaceutical ingredients (APIs) and 6 metabolites of interest, utilizing selective solid-phase extraction (SPE) and ultra performance liquid chromatography in combination with tripl...

40 CFR 141.40 - Monitoring requirements for unregulated contaminants.

Code of Federal Regulations, 2011 CFR

2011-07-01

... monitoring to be completed Reserved i Reserved i Reserved i Reserved i Reserved i Reserved i Column headings... Pesticides and Flame Retardants in Drinking Water by Solid Phase Extraction and Capillary Column Gas... Water by Solid Phase Extraction and Capillary Column Gas Chromatography/Mass Spectrometry (GC/MS...

Development of a Solid Phase Extraction Method for Agricultural Pesticides in Large-Volume Water Samples

EPA Science Inventory

An analytical method using solid phase extraction (SPE) and analysis by gas chromatography/mass spectrometry (GC/MS) was developed for the trace determination of a variety of agricultural pesticides and selected transformation products in large-volume high-elevation lake water sa...

AUTOMATED SOLID PHASE EXTRACTION GC/MS FOR ANALYSIS OF SEMIVOLATILES IN WATER AND SEDIMENTS

EPA Science Inventory

Data is presented on the development of a new automated system combining solid phase extraction (SPE) with GC/MS spectrometry for the single-run analysis of water samples containing a broad range of organic compounds. The system uses commercially available automated in-line sampl...

Processing Bi-Pb-Sr-Ca-Cu-O superconductors from amorphous state

NASA Technical Reports Server (NTRS)

Chiang, C. K.; Wong-Ng, W.; Cook, L. P.; Freiman, S. W.; Hwang, N. M.; Vaudin, M.; Hill, M. D.; Shull, R. D.; Shapiro, A. J.; Swartzendruber, L. J.

1991-01-01

The bismuth based high T sub c superconductors can be processed via an amorphous Bi-Pb-Sr-Ca-Cu oxide. The amorphous oxides were prepared by melting the constituent powders in an alumina crucible at 1200 C in air followed by pouring the liquid onto an aluminum plate, and rapidly pressing with a second plate. In the amorphous state, no crystalline phase was identified in the powder x ray diffraction pattern of the quenched materials. After heat treatment at high temperature the amorphous materials crystallized into a glass ceramic containing a large fraction of the Bi2Sr2Ca2Cu3O(x) phase T sub c = 110 K. The processing method, crystallization, and results of dc electrical resistivity and ac magnetic susceptibility measurements are discussed.

Deformability of adsorbents during adsorption and principles of the thermodynamics of solid-phase systems

NASA Astrophysics Data System (ADS)

Tovbin, Yu. K.

2017-09-01

A microscopic theory of adsorption, based on a discrete continuum lattice gas model for noninert (including deformable) adsorbents that change their lattice parameters during adsorption, is presented. Cases of the complete and partial equilibrium states of the adsorbent are considered. In the former, the adsorbent consists of coexisting solid and vapor phases of adsorbent components, and the adsorbate is a mobile component of the vapor phase with an arbitrary density (up to that of the liquid adsorbate phase). The adsorptive transitioning to the bound state changes the state of the near-surface region of the adsorbent. In the latter, there are no equilibrium components of the adsorbent between the solid and vapor phases. The adsorbent state is shown to be determined by its prehistory, rather than set by chemical potentials of vapor of its components. Relations between the microscopic theory and thermodynamic interpretations are discussed: (1) adsorption on an open surface, (2) two-dimensional stratification of the adsorbate mobile phase on an open homogeneous surface, (3) small microcrystals in vacuum and the gas phase, and (4) adsorption in porous systems.

Highly Accurate Calculations of the Phase Diagram of Cold Lithium

NASA Astrophysics Data System (ADS)

Shulenburger, Luke; Baczewski, Andrew

The phase diagram of lithium is particularly complicated, exhibiting many different solid phases under the modest application of pressure. Experimental efforts to identify these phases using diamond anvil cells have been complemented by ab initio theory, primarily using density functional theory (DFT). Due to the multiplicity of crystal structures whose enthalpy is nearly degenerate and the uncertainty introduced by density functional approximations, we apply the highly accurate many-body diffusion Monte Carlo (DMC) method to the study of the solid phases at low temperature. These calculations span many different phases, including several with low symmetry, demonstrating the viability of DMC as a method for calculating phase diagrams for complex solids. Our results can be used as a benchmark to test the accuracy of various density functionals. This can strengthen confidence in DFT based predictions of more complex phenomena such as the anomalous melting behavior predicted for lithium at high pressures. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. DOE's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Stability hierarchy between Piracetam forms I, II, and III from experimental pressure-temperature diagrams and topological inferences.

PubMed

Toscani, Siro; Céolin, René; Minassian, Léon Ter; Barrio, Maria; Veglio, Nestor; Tamarit, Josep-Lluis; Louër, Daniel; Rietveld, Ivo B

2016-01-30

The trimorphism of the active pharmaceutical ingredient piracetam is a famous case of polymorphism that has been frequently revisited by many researchers. The phase relationships between forms I, II, and III were ambiguous because they seemed to depend on the heating rate of the DSC and on the history of the samples or they have not been observed at all (equilibrium II-III). In the present paper, piezo-thermal analysis and high-pressure differential thermal analysis have been used to elucidate the positions of the different solid-solid and solid-liquid equilibria. The phase diagram, involving the three solid phases, the liquid phase and the vapor phase, has been constructed. It has been shown that form III is the high-pressure, low-temperature form and the stable form at room temperature. Form II is stable under intermediary conditions and form I is the low pressure, high temperature form, which possesses a stable melting point. The present paper demonstrates the strength of the topological approach based on the Clapeyron equation and the alternation rule when combined with high-pressure measurements. Copyright © 2015 Elsevier B.V. All rights reserved.

Coiled transmission line pulse generators

DOEpatents

McDonald, Kenneth Fox

2010-11-09

Methods and apparatus are provided for fabricating and constructing solid dielectric "Coiled Transmission Line" pulse generators in radial or axial coiled geometries. The pour and cure fabrication process enables a wide variety of geometries and form factors. The volume between the conductors is filled with liquid blends of monomers, polymers, oligomers, and/or cross-linkers and dielectric powders; and then cured to form high field strength and high dielectric constant solid dielectric transmission lines that intrinsically produce ideal rectangular high voltage pulses when charged and switched into matched impedance loads. Voltage levels may be increased by Marx and/or Blumlein principles incorporating spark gap or, preferentially, solid state switches (such as optically triggered thyristors) which produce reliable, high repetition rate operation. Moreover, these Marxed pulse generators can be DC charged and do not require additional pulse forming circuitry, pulse forming lines, transformers, or an a high voltage spark gap output switch. The apparatus accommodates a wide range of voltages, impedances, pulse durations, pulse repetition rates, and duty cycles. The resulting mobile or flight platform friendly cylindrical geometric configuration is much more compact, light-weight, and robust than conventional linear geometries, or pulse generators constructed from conventional components. Installing additional circuitry may accommodate optional pulse shape improvements. The Coiled Transmission Lines can also be connected in parallel to decrease the impedance, or in series to increase the pulse length.

A new RE + 011 TSIG method for the fabrication of high quality and large size single domain YBCO bulk superconductors

NASA Astrophysics Data System (ADS)

Yang, W. M.; Chen, L. P.; Wang, X. J.

2016-02-01

High quality single domain YBCO bulk superconductors, 20 mm in diameter, have been fabricated using a new top seeded infiltration and growth method (called the RE + 011 TSIG method), with a new solid phase (Y2O3 + xBaCuO2) instead of the conventional Y2BaCuO5 solid phase, x = 0, 0.5, 1.0, 1.2, 1.5, 1.8, 2.0, 2.5, 3.0. The effects of different BaCuO2 contents x on the growth morphology, microstructure, and levitation force have been investigated. The results show that the levitation force of the YBCO bulks first increases and then decreases with increasing x, and reaches maximum levitation forces of about 49.2 N (77 K, 0.5 T, with the traditional liquid phase of YBa2Cu3O y + 3 BaCuO2 + 2 CuO) and 47 N (77.3 K, 0.5 T, with the new liquid phase of Y2O3 + 10 BaCuO2 + 6 CuO) when x = 1.2, which is much higher than that of the samples fabricated with the conventional solid phases (23 N). The average Y2BaCuO5 particle size is about 1 μm, which is much smaller than the 3.4 μm in the samples prepared with the conventional Y2BaCuO5 solid phase; this means that the flux pinning force of the sample can be improved by using the new solid phase. Based on this method, single domain YBCO bulks 40 mm, 59 mm, and 93 mm in diameter have also been fabricated using the TSIG process with the new solid phases (Y2O3 + 1.2BaCuO2). These results indicate that the new TSIG process developed by our lab is a very important and practical method for the fabrication of low cost, large size, and high quality single domain REBCO bulk superconductors.

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2010 CFR

2010-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2014 CFR

2014-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2012 CFR

2012-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2011 CFR

2011-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2013 CFR

2013-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

Synthesis copolymer use to reduce pour point temperature of diamond crude oil

NASA Astrophysics Data System (ADS)

Than, Dao Viet; Chuong, Thai Hong; Tuy, Dao Quoc

2017-09-01

Diamond oil field is located in Block 01&02 Offshore Vietnam. Crude oil from Diamond Well Head Platform (WHP) is evacuated to FPSO via 20km 10" subsea flexible pipeline. The lowest seabed temperature in the field is 22°C, while the pour point temperature (PPT) of Diamond crude oil is very high (36°C) due to high paraffin content (25%). So studying to research a suitable Pour Point Depressant (PPD) for the crude oil is very important. The PPD must have ability to reduce pour point temperature of crude oil from 36°C to 21°C.

A three-dimensional phase field model for nanowire growth by the vapor-liquid-solid mechanism

NASA Astrophysics Data System (ADS)

Wang, Yanming; Ryu, Seunghwa; McIntyre, Paul C.; Cai, Wei

2014-07-01

We present a three-dimensional multi-phase field model for catalyzed nanowire (NW) growth by the vapor-liquid-solid (VLS) mechanism. The equation of motion contains both a Ginzburg-Landau term for deposition and a diffusion (Cahn-Hilliard) term for interface relaxation without deposition. Direct deposition from vapor to solid, which competes with NW crystal growth through the molten catalyst droplet, is suppressed by assigning a very small kinetic coefficient at the solid-vapor interface. The thermodynamic self-consistency of the model is demonstrated by its ability to reproduce the equilibrium contact angles at the VLS junction. The incorporation of orientation dependent gradient energy leads to faceting of the solid-liquid and solid-vapor interfaces. The model successfully captures the curved shape of the NW base and the Gibbs-Thomson effect on growth velocity.

Ab Initio Simulation Beryllium in Solid Molecular Hydrogen: Elastic Constant

NASA Astrophysics Data System (ADS)

Guerrero, Carlo L.; Perlado, Jose M.

2016-03-01

In systems of inertial confinement fusion targets Deuterium-Tritium are manufactured with a solid layer, it must have specific properties to increase the efficiency of ignition. Currently there have been some proposals to model the phases of hydrogen isotopes and hence their high pressure, but these works do not allow explaining some of the structures present at the solid phase change effect of increased pressure. By means of simulation with first principles methods and Quantum Molecular Dynamics, we compare the structural difference of solid molecular hydrogen pure and solid molecular hydrogen with beryllium, watching beryllium inclusion in solid hydrogen matrix, we obtain several differences in mechanical properties, in particular elastic constants. For C11 the difference between hydrogen and hydrogen with beryllium is 37.56%. This may produce a non-uniform initial compression and decreased efficiency of ignition.

Boron-Based Hydrogen Storage: Ternary Borides and Beyond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vajo, John J.

DOE continues to seek reversible solid-state hydrogen materials with hydrogen densities of ≥11 wt% and ≥80 g/L that can deliver hydrogen and be recharged at moderate temperatures (≤100 °C) and pressures (≤100 bar) enabling incorporation into hydrogen storage systems suitable for transportation applications. Boron-based hydrogen storage materials have the potential to meet the density requirements given boron’s low atomic weight, high chemical valance, and versatile chemistry. However, the rates of hydrogen exchange in boron-based compounds are thus far much too slow for practical applications. Although contributing to the high hydrogen densities, the high valance of boron also leads to slowmore » rates of hydrogen exchange due to extensive boron-boron atom rearrangements during hydrogen cycling. This rearrangement often leads to multiple solid phases occurring over hydrogen release and recharge cycles. These phases must nucleate and react with each other across solid-solid phase boundaries leading to energy barriers that slow the rates of hydrogen exchange. This project sought to overcome the slow rates of hydrogen exchange in boron-based hydrogen storage materials by minimizing the number of solid phases and the boron atom rearrangement over a hydrogen release and recharge cycle. Two novel approaches were explored: 1) developing matched pairs of ternary borides and mixed-metal borohydrides that could exchange hydrogen with only one hydrogenated phase (the mixed-metal borohydride) and only one dehydrogenated phase (the ternary boride); and 2) developing boranes that could release hydrogen by being lithiated using lithium hydride with no boron-boron atom rearrangement.« less

Commensurability and transformations of adsorbed phases on a heterogeneous solid with periodic distribution of surface energy

NASA Astrophysics Data System (ADS)

Cortés, Joaquin; Valencia, Eliana

1997-07-01

Monte Carlo experiments are used to investigate the adsorption of argon on a heterogeneous solid with a periodic distribution of surface energy. A study is made of the relation between the adsorbate molecule's diameter and the distance between the sites of maximum surface energy on the critical temperature, the observed phase changes, and the commensurability of the surface phase structure determined in the simulation.

Phase-field modeling of diffusional phase behaviors of solid surfaces: A case study of phase-separating Li XFePO 4 electrode particles

DOE PAGES

Heo, Tae Wook; Chen, Long-Qing; Wood, Brandon C.

2015-04-08

In this paper, we present a comprehensive phase-field model for simulating diffusion-mediated kinetic phase behaviors near the surface of a solid particle. The model incorporates elastic inhomogeneity and anisotropy, diffusion mobility anisotropy, interfacial energy anisotropy, and Cahn–Hilliard diffusion kinetics. The free energy density function is formulated based on the regular solution model taking into account the possible solute-surface interaction near the surface. The coherency strain energy is computed using the Fourier-spectral iterative-perturbation method due to the strong elastic inhomogeneity with a zero surface traction boundary condition. Employing a phase-separating Li XFePO 4 electrode particle for Li-ion batteries as a modelmore » system, we perform parametric three-dimensional computer simulations. The model permits the observation of surface phase behaviors that are different from the bulk counterpart. For instance, it reproduces the theoretically well-established surface modes of spinodal decomposition of an unstable solid solution: the surface mode of coherent spinodal decomposition and the surface-directed spinodal decomposition mode. We systematically investigate the influences of major factors on the kinetic surface phase behaviors during the diffusional process. Finally, our simulation study provides insights for tailoring the internal phase microstructure of a particle by controlling the surface phase morphology.« less

Evaluation of the solubility constants of the hydrated solid phases in the H2O-Al2O3-SO3 ternary system

NASA Astrophysics Data System (ADS)

Teyssier, A.; Lagneau, V.; Schmitt, J. M.; Counioux, J. J.; Goutaudier, C.

2017-04-01

During the acid processing of aluminosilicate ores, the precipitation of a solid phase principally consisting of hydrated aluminium hydroxysulfates may be observed. The experimental study of the H2O-Al2O3-SO3 ternary system at 25 ∘C and 101 kPa enabled to describe the solid-liquid equilibra and to identify the nature, the composition and the solubility of the solid phases which may form during the acid leaching. To predict the appearance of these aluminium hydroxysulfates in more complex systems, their solubility constants were calculated by modelling the experimental solubility results, using a geochemical reaction modelling software, CHESS. A model for non-ideality correction, based on the B-dot equation, was used as it was suitable for the considered ion concentration range. The solubility constants of three out of four solid phases were calculated: 104.08 for jurbanite (Al(SO4)(OH).5H2O), 1028.09 for the solid T (Al8(SO4)5(OH)14.34H2O) and 1027.28 for the solid V (Al10(SO4)3(OH)24.20H2O). However the activity correction model was not suitable to determine the solubility constant of alunogen (Al2(SO4)3.15.8H2O), as the ion concentrations of the mixtures were too high and beyond the allowable limits of the model. Another ionic activity correction model, based on the Pitzer equation for example, must be applied to calculate the solubility constant of alunogen.

Bacterial toxicity assessment of drinking water treatment residue (DWTR) and lake sediment amended with DWTR.

PubMed

Yuan, Nannan; Wang, Changhui; Pei, Yuansheng

2016-11-01

Drinking water treatment residue (DWTR) seems to be very promising for controlling lake sediment pollution. Logically, acquisition of the potential toxicity of DWTR will be beneficial for its applications. In this study, the toxicity of DWTR and sediments amended with DWTR to Aliivibrio fischeri was evaluated based on the Microtox(®) solid and leachate phase assays, in combination with flow cytometry analyses and the kinetic luminescent bacteria test. The results showed that both solid particles and aqueous/organic extracts of DWTR exhibited no toxicity to the bacterial luminescence and growth. The solid particles of DWTR even promoted bacterial luminescence, possibly because DWTR particles could act as a microbial carrier and provide nutrients for bacteria growth. Bacterial toxicity (either luminescence or growth) was observed from the solid phase and aqueous/organic extracts of sediments with or without DWTR addition. Further analysis showed that the solid phase toxicity was determined to be related mainly to the fixation of bacteria to fine particles and/or organic matter, and all of the observed inhibition resulting from aqueous/organic extracts was identified as non-significant. Moreover, DWTR addition not only had no adverse effect on the aqueous/organic extract toxicity of the sediment but also reduced the solid phase toxicity of the sediment. Overall, in practical application, the solid particles, the water-soluble substances transferred to surface water or the organic substances in DWTR had no toxicity or any delayed effect on bacteria in lakes, and DWTR can therefore be considered as a non-hazardous material. Copyright © 2016 Elsevier Ltd. All rights reserved.

Solid Polymer Electrolyte (SPE) fuel cell technology program

NASA Technical Reports Server (NTRS)

1979-01-01

The overall objectives of the Phase IV Solid Polymer Electrolyte Fuel Cell Technology Program were to: (1) establish fuel cell life and performance at temperatures, pressures and current densities significantly higher than those previously demonstrated; (2) provide the ground work for a space energy storage system based on the solid polymer electrolyte technology (i.e., regenerative H2/O2 fuel cell); (3) design, fabricate and test evaluate a full-scale single cell unit. During this phase, significant progress was made toward the accomplishment of these objectives.

Phase equilibria of H2SO4, HNO3, and HCl hydrates and the composition of polar stratospheric clouds

NASA Technical Reports Server (NTRS)

Wooldridge, Paul J.; Zhang, Renyi; Molina, Mario J.

1995-01-01

Thermodynamic properties and phase equilibria behavior for the hydrates and coexisting pairs of hydrates of common acids which exist in the stratosphere are assembled from new laboratory measurements and standard literature data. The analysis focuses upon solid-vapor and solid-solid-vapor equilibria at temperatures around 200 K and includes new calorimetric and vapor pressure data. Calculated partial pressures versus 1/T slopes for the hydrates and coexisting hydrates agree well with experimental data where available.

Phase Equilibria of H2SO4, HNO3, and HCl Hydrates and the Composition of Polar Stratospheric Clouds

NASA Technical Reports Server (NTRS)

Wooldridge, Paul J.; Zhang, Renyi; Molina, Mario J.

1995-01-01

Thermodynamic properties and phase equilibria behavior for the hydrates and coexisting pairs of hydrates of common acids which exist in the stratosphere are assembled from new laboratory measurements and standard literature data. The analysis focuses upon solid-vapor and solid-solid-vapor equilibria at temperatures around 200 K and includes new calorimetric and vapor pressure data. Calculated partial pressures versus 1/T slopes for the hydrates and coexisting hydrates agree well with experimental data where available.