The conversion of lignocellulosics to fermentable sugars - A survey of current research and applications to CELSS

NASA Technical Reports Server (NTRS)

Petersen, Gene R.; Baresi, Larry

1990-01-01

This report provides an overview options for converting lignocellulosics into fermentable sugars in CELSS. A requirement for pretreatment is shown. Physical-chemical and enzymatic hydrolysis processes for producing fermentable sugars are discussed. At present physical-chemical methods are the simplest and best characterized options, but enzymatic processes will be the likely method of choice in the future. The use of pentose sugars by microorganisms to produce edibles is possible. The use of mycelial food production on pretreated but not hydrolyzed lignocellulosics is also possible. Simple trade-off analyses to regenerate waste lignocellulosics for two pathways are made, one of which is compared to complete oxidation.

Review of surface steam sterilization for validation purposes.

PubMed

van Doornmalen, Joost; Kopinga, Klaas

2008-03-01

Sterilization is an essential step in the process of producing sterile medical devices. To guarantee sterility, the process of sterilization must be validated. Because there is no direct way to measure sterility, the techniques applied to validate the sterilization process are based on statistical principles. Steam sterilization is the most frequently applied sterilization method worldwide and can be validated either by indicators (chemical or biological) or physical measurements. The steam sterilization conditions are described in the literature. Starting from these conditions, criteria for the validation of steam sterilization are derived and can be described in terms of physical parameters. Physical validation of steam sterilization appears to be an adequate and efficient validation method that could be considered as an alternative for indicator validation. Moreover, physical validation can be used for effective troubleshooting in steam sterilizing processes.

Microbial mats as a biological treatment approach for saline wastewaters: the case of produced water from hydraulic fracturing.

PubMed

Akyon, Benay; Stachler, Elyse; Wei, Na; Bibby, Kyle

2015-05-19

Treatment of produced water, i.e. wastewater from hydraulic fracturing, for reuse or final disposal is challenged by both high salinity and the presence of organic compounds. Organic compounds in produced water may foul physical-chemical treatment processes or support microbial corrosion, fouling, and sulfide release. Biological approaches have potential applications in produced water treatment, including reducing fouling of physical-chemical treatment processes and decreasing biological activity during produced water holding; however, conventional activated sludge treatments are intolerant of high salinity. In this study, a biofilm treatment approach using constructed microbial mats was evaluated for biodegradation performance, microbial community structure, and metabolic potential in both simulated and real produced water. Results demonstrated that engineered microbial mats are active at total dissolved solids (TDS) concentrations up to at least 100,000 mg/L, and experiments in real produced water showed a biodegradation capacity of 1.45 mg COD/gramwet-day at a TDS concentration of 91,351 mg/L. Additionally, microbial community and metagenomic analyses revealed an adaptive microbial community that shifted based upon the sample being treated and has the metabolic potential to degrade a wide array of contaminants, suggesting the potential of this approach to treat produced waters with varying composition.

10 CFR 1017.28 - Processing on Automated Information Systems (AIS).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Processing on Automated Information Systems (AIS). 1017.28... UNCLASSIFIED CONTROLLED NUCLEAR INFORMATION Physical Protection Requirements § 1017.28 Processing on Automated Information Systems (AIS). UCNI may be processed or produced on any AIS that complies with the guidance in OMB...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anameric, B.; Kawatra, S.K.

Pig iron nuggets were produced in a laboratory-scale furnace at Michigan Technological University. The process was intended to replicate Kobe Steel's ITmk3 direct ironmaking process. These nuggets were produced from pellets that were made from a mixture of iron oxide, coal, flux and a binder and heated in a furnace with a chamber temperature of 1450{sup o}C. The pellets then self-reduced to produce a solid, high-density, highly metallized (96.5% Fe) pig iron. During the nugget production process, a separate liquid slag phase formed that cleanly separated from the molten metal. The physical and chemical properties of the pig iron nuggetsmore » were similar to pig iron produced by blast furnaces, which is distinct from direct reduced iron (DRI).« less

FIRST ORDER KINETIC GAS GENERATION MODEL PARAMETERS FOR WET LANDFILLS

EPA Science Inventory

Landfill gas is produced as a result of a sequence of physical, chemical, and biological processes occurring within an anaerobic landfill. Landfill operators, energy recovery project owners, regulators, and energy users need to be able to project the volume of gas produced and re...

A Molecular Explanation of How the Fog Is Produced When Dry Ice Is Placed in Water

ERIC Educational Resources Information Center

Kuntzleman, Thomas S.; Ford, Nathan; No, Jin-Hwan; Ott, Mark E.

2015-01-01

Everyone enjoys seeing the cloudy white fog generated when solid carbon dioxide (dry ice) is placed in water. Have you ever wondered what physical and chemical processes occur to produce this fog? When asked this question, many chemical educators suggest that the fog is produced when atmospheric water vapor condenses on cold carbon dioxide gas…

A Computerized Bibliographic Service for the Blind and Physically Handicapped

ERIC Educational Resources Information Center

Friedman, Morton H.

1975-01-01

Describes a three-year plan and a system study designed to produce a computerized union catalog and an in-process file for both the Library of Congress Division for the Blind and Physically Handicapped and a network of almost 200 libraries throughout the nation. (Author/PF)

Numerical Modeling of Fiber-Reinforced Metal Matrix Composite Processing by the Liquid Route: Literature Contribution

NASA Astrophysics Data System (ADS)

Lacoste, Eric; Arvieu, Corinne; Mantaux, Olivier

2018-04-01

One of the technologies used to produce metal matrix composites (MMCs) is liquid route processing. One solution is to inject a liquid metal under pressure or at constant rate through a fibrous preform. This foundry technique overcomes the problem of the wettability of ceramic fibers by liquid metal. The liquid route can also be used to produce semiproducts by coating a filament with a molten metal. These processes involve physical phenomena combined with mass and heat transfer and phase change. The phase change phenomena related to solidification and also to the melting of the metal during the process notably result in modifications to the permeability of porous media, in gaps in impregnation, in the appearance of defects (porosities), and in segregation in the final product. In this article, we provide a state-of-the-art review of numerical models and simulation developed to study these physical phenomena involved in MMC processing by the liquid route.

Chemical characterization of chars developed from thermochemical treatment of Kentucky bluegrass seed screenings

USDA-ARS?s Scientific Manuscript database

Char produced from the gasification of post-seed harvest Kentucky bluegrass residues could be recycled to a cropping system as a soil amendment if chemical characterization determined that the gasification process had not produced or concentrated deleterious chemical or physical factors that might h...

Physical Origins of Space Weather Impacts: Open Physics Questions

NASA Astrophysics Data System (ADS)

Lanzerotti, L. J.

2011-12-01

Beginning with the era of development of electrical telegraph systems in the early 19th century, physical processes in the space environment on the Sun, in the interplanetary medium, and around Earth have influenced the design and operations of ever-increasing and sophisticated technical systems, both in space and on the ground. Understanding of Earth's space environment has increased enormously in the last century and one-half. Nevertheless, many of the physical processes that produced effects on early cable and wireless technologies continue to plague modern-day systems. And as new technologies are developed for improved communications, surveillance, navigation, and conditions for human space flight, the solar-terrestrial environment often offers surprises to their safe, secure and uninterrupted operations. This talk will address some of the challenges that I see to the successful operations of some modern-day technical systems that are posed by significant deficiencies of understanding of physical processes operating from the Sun to the Earth.

NASA GPM GV Science Implementation

NASA Technical Reports Server (NTRS)

Petersen, W. A.

2009-01-01

Pre-launch algorithm development & post-launch product evaluation: The GPM GV paradigm moves beyond traditional direct validation/comparison activities by incorporating improved algorithm physics & model applications (end-to-end validation) in the validation process. Three approaches: 1) National Network (surface): Operational networks to identify and resolve first order discrepancies (e.g., bias) between satellite and ground-based precipitation estimates. 2) Physical Process (vertical column): Cloud system and microphysical studies geared toward testing and refinement of physically-based retrieval algorithms. 3) Integrated (4-dimensional): Integration of satellite precipitation products into coupled prediction models to evaluate strengths/limitations of satellite precipitation producers.

Multi-Physics Modeling of Molten Salt Transport in Solid Oxide Membrane (SOM) Electrolysis and Recycling of Magnesium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Powell, Adam; Pati, Soobhankar

2012-03-11

Solid Oxide Membrane (SOM) Electrolysis is a new energy-efficient zero-emissions process for producing high-purity magnesium and high-purity oxygen directly from industrial-grade MgO. SOM Recycling combines SOM electrolysis with electrorefining, continuously and efficiently producing high-purity magnesium from low-purity partially oxidized scrap. In both processes, electrolysis and/or electrorefining take place in the crucible, where raw material is continuously fed into the molten salt electrolyte, producing magnesium vapor at the cathode and oxygen at the inert anode inside the SOM. This paper describes a three-dimensional multi-physics finite-element model of ionic current, fluid flow driven by argon bubbling and thermal buoyancy, and heat andmore » mass transport in the crucible. The model predicts the effects of stirring on the anode boundary layer and its time scale of formation, and the effect of natural convection at the outer wall. MOxST has developed this model as a tool for scale-up design of these closely-related processes.« less

Physics and biochemical engineering: 3

NASA Astrophysics Data System (ADS)

Fairbrother, Robert; Riddle, Wendy; Fairbrother, Neil

2006-09-01

Once an antibiotic has been produced on a large scale, as described in our preceding articles, it has to be extracted and purified. Filtration and centrifugation are the two main ways of doing this, and the design of industrial processing systems is governed by simple physics involving factors such as pressure, viscosity and rotational motion.

Lithium Gadolinium Borate in Plastic Scintillator as an Antineutrino Detection Material

DTIC Science & Technology

2010-06-01

advancement of fundamental particle physics, development of the standard model of particle physics and our understanding many cosmological processes...MeVee). Where the light produced by by a 1MeV electron is 1 MeVee by definition , but a heavy charged particle would have a kinetic energy of several

The Adiabatic Expansion of Gases and the Determination of Heat Capacity Ratios: A Physical Chemistry Experiment.

ERIC Educational Resources Information Center

Moore, William M.

1984-01-01

Describes the procedures and equipment for an experiment on the adiabatic expansion of gases suitable for demonstration and discussion in the physical chemical laboratory. The expansion produced shows how the process can change temperature and still return to a different location on an isotherm. (JN)

Optimization of the treatment cycle of pressed-off leachate produced in a facility processing the organic fraction of municipal solid waste.

PubMed

d'Antonio, Luca; Fabbricino, Massimiliano; Pontoni, Ludovico

2015-01-01

The paper investigates, at a laboratory scale, the applicability of anaerobic digestion for the treatment of pressed-off leachate produced in a biomechanical treatment plant for municipal solid waste. Batch tests show that the anaerobic process proceeds smoothly and produces about 10,000 mL of methane per litre of treated leachate. The process is characterized by a lag phase lasting about 30 days, and is completed in about 2 months. Chemical oxygen demand (COD) and volatile fatty acids monitoring allows studying process kinetics that are modelled through a triple linear expression. Physical and biological treatments are also investigated to reduce the residual organic charge of the produced digestate. The best performances are obtained via aerobic degradation followed by assisted sedimentation. This cycle reduces the residual COD of about 85%, and allows the correct disposal of the final waste stream.

Is the Brain a Quantum Computer?

ERIC Educational Resources Information Center

Litt, Abninder; Eliasmith, Chris; Kroon, Frederick W.; Weinstein, Steven; Thagard, Paul

2006-01-01

We argue that computation via quantum mechanical processes is irrelevant to explaining how brains produce thought, contrary to the ongoing speculations of many theorists. First, quantum effects do not have the temporal properties required for neural information processing. Second, there are substantial physical obstacles to any organic…

Research Update - Intervention Technologies for Enhancing the Safety and Security of Fresh and Minimally Processed Produce and Solid Plant-Derived Foods

USDA-ARS?s Scientific Manuscript database

The produce safety research objectives of Research Project 1935-41420-011 are to 1) understand pathogen microbial ecology and its effects on decontamination efficacy; 2) develop biological-based intervention strategies for pathogen reduction; and 3) develop new effective chemical and physical decont...

Geological Implications of a Physical Libration on Enceladus

NASA Technical Reports Server (NTRS)

Hurford, T. A.; Bills, B. G.; Helfenstein, P.; Greenberg, R.; Hoppa, G. V.; Hamilton, D. P.

2008-01-01

Given the non-spherical shape of Enceladus (Thomas et al., 2007), the satellite will experience gravitational torques that will cause it to physically librate as it orbits Saturn. Physical libration would produce a diurnal oscillation in the longitude of Enceladus tidal bulge which, could have a profound effect on the diurnal stresses experienced by the surface of the satellite. Although Cassini ISS has placed an observational upper limit on Enceladus libration amplitude of F < 1.5deg (Porco et al., 2006), smaller amplitudes can still have geologically significant consequences. Here we present the first detailed description of how physical libration affects tidal stresses and how those stresses then might affect geological processes including crack formation and propagation, south polar eruption activity, and tidal heating. Our goal is to provide a framework for testing the hypothesis that geologic features on Enceladus are produced by tidal stresses from diurnal physical and optical librations of the satellite.

ERP differences between processing of physical characteristics and personality attributes

PubMed Central

2012-01-01

Background Limited data from behavioral and brain-imaging studies indicate that personality traits and physical characteristics are processed differently by the brain. Additionally, electrophysiological results of studies comparing the processing of positive and negative words have produced mixed results. It is therefore not clear how physical and personality attributes with emotional valence (i.e., positive and negative valence) are processed. Thus, this study aimed to examine the neural activity associated with words describing personality traits and physical characteristics with positive or negative emotional valence using Event Related Potentials (ERPs). Methods A sample of 15 healthy adults (7 men, 8 women) participated in a computerized word categorization task. Participants were asked to categorize visual word stimuli as physical characteristics or personality traits, while ERPs were recorded synchronously. Results Behavioral reaction times to negative physical stimuli were shorter compared to negative personality words, however reaction times did not significantly differ for positive stimuli. Electrophysiological results showed that personality stimuli elicited larger P2 and LPC (Late Positive Component) amplitudes compared to physical stimuli, regardless of negative or positive valence. Moreover, negative as compared with positive stimuli elicited larger P2 and LPC amplitudes. Conclusion Personality and physical stimuli were processed differently regardless of positive or negative valence. These findings suggest that personality traits and physical characteristics are differentially classified and are associated with different motivational significance. PMID:22967478

MAUVE: A New Strategy for Solving and Grading Physics Problems

NASA Astrophysics Data System (ADS)

Hill, Nicole Breanne

2016-05-01

MAUVE (magnitude, answer, units, variables, and equations) is a framework and rubric to help students and teachers through the process of clearly solving and assessing solutions to introductory physics problems. Success in introductory physics often derives from an understanding of units, a command over dimensional analysis, and good bookkeeping. I developed MAUVE for an introductory-level environmental physics course as an easy-to-remember checklist to help students construct organized and thoughtful solutions to physics problems. Environmental physics is a core physics course for environmental and sustainability science (ESS) majors that teaches principles of radiation, thermodynamics, and mechanics within the context of the environment and sustainable energy systems. ESS student concentrations include environmental biology, applied ecology, biogeochemistry, and natural resources. The MAUVE rubric, inspired by nature, has encouraged my students to produce legible and tactical work, and has significantly clarified the grading process.

In-space fabrication of thin-film structures

NASA Technical Reports Server (NTRS)

Lippman, M. E.

1972-01-01

A conceptual study of physical vapor-deposition processes for in-space fabrication of thin-film structures is presented. Potential advantages of in-space fabrication are improved structural integrity and surface reflectivity of free-standing ultra-thin films and coatings. Free-standing thin-film structures can find use as photon propulsion devices (solar sails). Other applications of the concept involve free-standing shadow shields, or thermal control coatings of spacecraft surfaces. Use of expendables (such as booster and interstage structures) as source material for the physical vapor deposition process is considered. The practicability of producing thin, textured, aluminum films by physical vapor deposition and subsequent separation from a revolving substrate is demonstrated by laboratory experiments. Heating power requirement for the evaporation process is estimated for a specific mission.

Biomedically relevant chemical and physical properties of coal combustion products.

PubMed Central

Fisher, G L

1983-01-01

The evaluation of the potential public and occupational health hazards of developing and existing combustion processes requires a detailed understanding of the physical and chemical properties of effluents available for human and environmental exposures. These processes produce complex mixtures of gases and aerosols which may interact synergistically or antagonistically with biological systems. Because of the physicochemical complexity of the effluents, the biomedically relevant properties of these materials must be carefully assessed. Subsequent to release from combustion sources, environmental interactions further complicate assessment of the toxicity of combustion products. This report provides an overview of the biomedically relevant physical and chemical properties of coal fly ash. Coal fly ash is presented as a model complex mixture for health and safety evaluation of combustion processes. PMID:6337824

Development of materials for the rapid manufacture of die cast tooling

NASA Astrophysics Data System (ADS)

Hardro, Peter Jason

The focus of this research is to develop a material composition that can be processed by rapid prototyping (RP) in order to produce tooling for the die casting process. Where these rapidly produced tools will be superior to traditional tooling production methods by offering one or more of the following advantages: reduced tooling cost, shortened tooling creation time, reduced man-hours for tool creation, increased tool life, and shortened die casting cycle time. By utilizing RP's additive build process and vast material selection, there was a prospect that die cast tooling may be produced quicker and with superior material properties. To this end, the material properties that influence die life and cycle time were determined, and a list of materials that fulfill these "optimal" properties were highlighted. Physical testing was conducted in order to grade the processability of each of the material systems and to optimize the manufacturing process for the downselected material system. Sample specimens were produced and microscopy techniques were utilized to determine a number of physical properties of the material system. Additionally, a benchmark geometry was selected and die casting dies were produced from traditional tool materials (H13 steel) and techniques (machining) and from the newly developed materials and RP techniques (selective laser sintering (SLS) and laser engineered net shaping (LENS)). Once the tools were created, a die cast alloy was selected and a preset number of parts were shot into each tool. During tool creation, the manufacturing time and cost was closely monitored and an economic model was developed to compare traditional tooling to RP tooling. This model allows one to determine, in the early design stages, when it is advantageous to implement RP tooling and when traditional tooling would be best. The results of the physical testing and economic analysis has shown that RP tooling is able to achieve a number of the research objectives, namely, reduce tooling cost, shorten tooling creation time, and reduce the man-hours needed for tool creation. Though identifying the appropriate time to use RP tooling appears to be the most important aspect in achieving successful implementation.

Downstream processing of stevioside and its potential applications.

PubMed

Puri, Munish; Sharma, Deepika; Tiwari, Ashok K

2011-01-01

Stevioside is a natural sweetener extracted from leaves of Stevia rebaudiana Bertoni, which is commercially produced by conventional (chemical/physical) processes. This article gives an overview of the stevioside structure, various analysis technique, new technologies required and the advances achieved in recent years. An enzymatic process is established, by which the maximum efficacy and benefit of the process can be achieved. The efficiency of the enzymatic process is quite comparable to that of other physical and chemical methods. Finally, we believe that in the future, the enzyme-based extraction will ensure more cost-effective availability of stevioside, thus assisting in the development of more food-based applications. Copyright © 2011 Elsevier Inc. All rights reserved.

Rice Physiology

Treesearch

P.A. Counce; Davidi R. Gealy; Shi-Jean Susana Sung

2002-01-01

Physiology occurs tn physical space through chemical reactions constrained by anatomy and morphology, yet guided by genetics. Physiology has been called the logic of life. Genes encode structural and fimcdonal proteins. These proteins are subsequently processed to produce enzymes that direct and govern the biomechanical processes involved in the physiology of the...

Anti-reflection coatings applied by acid leaching process

NASA Technical Reports Server (NTRS)

Pastirik, E.

1980-01-01

The Magicote C process developed by S.M. Thompsen was evaluated for use in applying an antireflective coating to the cover plates of solar panels. The process uses a fluosilicic acid solution supersaturated with silica at elevated temperature to selectively attack the surface of soda-lime glass cover plates and alter the physical and chemical composition of a thin layer of glass. The altered glass layer constitutes an antireflective coating. The process produces coatings of excellent optical quality which possess outstanding resistance to soiling and staining. The coatings produced are not resistant to mechanical abrasion and are attacked to some extent by glass cleansers. Control of the filming process was found to be difficult.

The effects of baryon physics, black holes and active galactic nucleus feedback on the mass distribution in clusters of galaxies

NASA Astrophysics Data System (ADS)

Martizzi, Davide; Teyssier, Romain; Moore, Ben; Wentz, Tina

2012-06-01

The spatial distribution of matter in clusters of galaxies is mainly determined by the dominant dark matter component; however, physical processes involving baryonic matter are able to modify it significantly. We analyse a set of 500 pc resolution cosmological simulations of a cluster of galaxies with mass comparable to Virgo, performed with the AMR code RAMSES. We compare the mass density profiles of the dark, stellar and gaseous matter components of the cluster that result from different assumptions for the subgrid baryonic physics and galaxy formation processes. First, the prediction of a gravity-only N-body simulation is compared to that of a hydrodynamical simulation with standard galaxy formation recipes, and then all results are compared to a hydrodynamical simulation which includes thermal active galactic nucleus (AGN) feedback from supermassive black holes (SMBHs). We find the usual effects of overcooling and adiabatic contraction in the run with standard galaxy formation physics, but very different results are found when implementing SMBHs and AGN feedback. Star formation is strongly quenched, producing lower stellar densities throughout the cluster, and much less cold gas is available for star formation at low redshifts. At redshift z= 0 we find a flat density core of radius 10 kpc in both the dark and stellar matter density profiles. We speculate on the possible formation mechanisms able to produce such cores and we conclude that they can be produced through the coupling of different processes: (I) dynamical friction from the decay of black hole orbits during galaxy mergers; (II) AGN-driven gas outflows producing fluctuations of the gravitational potential causing the removal of collisionless matter from the central region of the cluster; (III) adiabatic expansion in response to the slow expulsion of gas from the central region of the cluster during the quiescent mode of AGN activity.

Take the Pencil out of the Process

ERIC Educational Resources Information Center

Broun, Leslie

2009-01-01

In classrooms, it is not unusual to see students who struggle to produce legible print. In actuality, many students have difficulty with the physical printing and writing processes ("handwriting")--difficulty that is significant enough to interfere with their academic performance. Some students grow out of this, and some, with extra practice,…

Transient Dissipation and Structural Costs of Physical Information Transduction

NASA Astrophysics Data System (ADS)

Boyd, Alexander B.; Mandal, Dibyendu; Riechers, Paul M.; Crutchfield, James P.

2017-06-01

A central result that arose in applying information theory to the stochastic thermodynamics of nonlinear dynamical systems is the information-processing second law (IPSL): the physical entropy of the Universe can decrease if compensated by the Shannon-Kolmogorov-Sinai entropy change of appropriate information-carrying degrees of freedom. In particular, the asymptotic-rate IPSL precisely delineates the thermodynamic functioning of autonomous Maxwellian demons and information engines. How do these systems begin to function as engines, Landauer erasers, and error correctors? We identify a minimal, and thus inescapable, transient dissipation of physical information processing, which is not captured by asymptotic rates, but is critical to adaptive thermodynamic processes such as those found in biological systems. A component of transient dissipation, we also identify an implementation-dependent cost that varies from one physical substrate to another for the same information processing task. Applying these results to producing structured patterns from a structureless information reservoir, we show that "retrodictive" generators achieve the minimal costs. The results establish the thermodynamic toll imposed by a physical system's structure as it comes to optimally transduce information.

Graduate Physics Education Adding Industrial Culture and Methods to a Traditional Graduate Physics Department

NASA Astrophysics Data System (ADS)

Vickers, Ken

2005-03-01

The education and training of the workforce needed to assure global competitiveness of American industry in high technology areas, along with the proper role of various disciplines in that educational process, is currently being re-examined. Several academic areas in science and engineering have reported results from such studies that revealed several broad themes of educational need that span and cross the boundaries of science and engineering. They included greater attention to and the development of team-building skills, personal or interactive skills, creative ability, and a business or entrepreneurial where-with-all. We will report in this paper the results of a fall 2000 Department of Education FIPSE grant to implement changes in its graduate physics program to address these issues. The proposal goal was to produce next-generation physics graduate students that are trained to evaluate and overcome complex technical problems by their participation in courses emphasizing the commercialization of technology research. To produce next-generation physics graduates who have learned to work with their student colleagues for their mutual success in an industrial-like group setting. And finally, to produce graduates who can lead interdisciplinary groups in solving complex problems in their career field.

The effects of physical activity on impulsive choice: Influence of sensitivity to reinforcement amount and delay

PubMed Central

Strickland, Justin C.; Feinstein, Max A.; Lacy, Ryan T.; Smith, Mark A.

2016-01-01

Impulsive choice is a diagnostic feature and/or complicating factor for several psychological disorders and may be examined in the laboratory using delay-discounting procedures. Recent investigators have proposed using quantitative measures of analysis to examine the behavioral processes contributing to impulsive choice. The purpose of this study was to examine the effects of physical activity (i.e., wheel running) on impulsive choice in a single-response, discrete-trial procedure using two quantitative methods of analysis. To this end, rats were assigned to physical activity or sedentary groups and trained to respond in a delay-discounting procedure. In this procedure, one lever always produced one food pellet immediately, whereas a second lever produced three food pellets after a 0, 10, 20, 40, or 80-second delay. Estimates of sensitivity to reinforcement amount and sensitivity to reinforcement delay were determined using (1) a simple linear analysis and (2) an analysis of logarithmically transformed response ratios. Both analyses revealed that physical activity decreased sensitivity to reinforcement amount and sensitivity to reinforcement delay. These findings indicate that (1) physical activity has significant but functionally opposing effects on the behavioral processes that contribute to impulsive choice and (2) both quantitative methods of analysis are appropriate for use in single-response, discrete-trial procedures. PMID:26964905

Food processors requirements met by radiation processing

NASA Astrophysics Data System (ADS)

Durante, Raymond W.

2002-03-01

Processing food using irradiation provides significant advantages to food producers by destroying harmful pathogens and extending shelf life without any detectable physical or chemical changes. It is expected that through increased public education, food irradiation will emerge as a viable commercial industry. Food production in most countries involves state of the art manufacturing, packaging, labeling, and shipping techniques that provides maximum efficiency and profit. In the United States, food sales are extremely competitive and profit margins small. Most food producers have heavily invested in equipment and are hesitant to modify their equipment. Meat and poultry producers in particular utilize sophisticated production machinery that processes enormous volumes of product on a continuous basis. It is incumbent on the food irradiation equipment suppliers to develop equipment that can easily merge with existing processes without requiring major changes to either the final food product or the process utilized to produce that product. Before a food producer can include irradiation as part of their food production process, they must be certain the available equipment meets their needs. This paper will examine several major requirements of food processors that will most likely have to be provided by the supplier of the irradiation equipment.

Modeling Forced Imbibition Processes and the Associated Seismic Attenuation in Heterogeneous Porous Rocks

NASA Astrophysics Data System (ADS)

Solazzi, Santiago G.; Guarracino, Luis; Rubino, J. Germán.; Müller, Tobias M.; Holliger, Klaus

2017-11-01

Quantifying seismic attenuation during laboratory imbibition experiments can provide useful information toward the use of seismic waves for monitoring injection and extraction of fluids in the Earth's crust. However, a deeper understanding of the physical causes producing the observed attenuation is needed for this purpose. In this work, we analyze seismic attenuation due to mesoscopic wave-induced fluid flow (WIFF) produced by realistic fluid distributions representative of imbibition experiments. To do so, we first perform two-phase flow simulations in a heterogeneous rock sample to emulate a forced imbibition experiment. We then select a subsample of the considered rock containing the resulting time-dependent saturation fields and apply a numerical upscaling procedure to compute the associated seismic attenuation. By exploring both saturation distributions and seismic attenuation, we observe that two manifestations of WIFF arise during imbibition experiments: the first one is produced by the compressibility contrast associated with the saturation front, whereas the second one is due to the presence of patches containing very high amounts of water that are located behind the saturation front. We demonstrate that while the former process is expected to play a significant role in the case of high injection rates, which are associated with viscous-dominated imbibition processes, the latter becomes predominant during capillary-dominated processes, that is, for relatively low injection rates. We conclude that this kind of joint numerical analysis constitutes a useful tool for improving our understanding of the physical mechanisms producing seismic attenuation during laboratory imbibition experiments.

Computer model for economic study of unbleached kraft paperboard production

Treesearch

Peter J. Ince

1984-01-01

Unbleached kraft paperboard is produced from wood fiber in an industrial papermaking process. A highly specific and detailed model of the process is presented. The model is also presented as a working computer program. A user of the computer program will provide data on physical parameters of the process and on prices of material inputs and outputs. The program is then...

A new mechanism for relativistic particle acceleration via wave-particle interaction

NASA Astrophysics Data System (ADS)

Lapenta, Giovanni; Markidis, Stefano; Marocchino, Alberto

2006-10-01

Often in laboratory, space and astrophysical plasma, high energy populations are observed. Two puzzling factors still defy our understanding. First, such populations of high energy particles produce power law distributions that are not only ubiquitous but also persistent in time. Such persistence is in direct contradiction to the H theorem that states the ineluctable transition of physical systems towards thermodynamic equilibrium, and ergo Maxwellian distributions. Second, such high energy populations are efficiently produced, much more efficiently than processes that we know can produce. A classic example of such a situation is cosmic rays where power alws extend up to tremendolus energy ranges. In the present work, we identify a new mechanism for particle acceleration via wave-particle interaction. The mechanism is peculiar to special relativity and has no classical equivalent. That explains why it is not observed in most simulation studies of plasma processes, based on classical physics. The mechanism is likely to be active in systems undergoing streaming instabilities and in particular shocked systems. The new mechanism can produce energy increases vastly superior to previously known mechanisms (such as Fermi acceleration) and can hold the promise of explaining at least some of the observed power laws.

Statistical physics of self-replication.

PubMed

England, Jeremy L

2013-09-28

Self-replication is a capacity common to every species of living thing, and simple physical intuition dictates that such a process must invariably be fueled by the production of entropy. Here, we undertake to make this intuition rigorous and quantitative by deriving a lower bound for the amount of heat that is produced during a process of self-replication in a system coupled to a thermal bath. We find that the minimum value for the physically allowed rate of heat production is determined by the growth rate, internal entropy, and durability of the replicator, and we discuss the implications of this finding for bacterial cell division, as well as for the pre-biotic emergence of self-replicating nucleic acids.

Science and Science Fiction

ScienceCinema

Scherrer, Robert [Vanderbilt University, Nashville, Tennessee, United States

2017-12-09

I will explore the similarities and differences between the process of writing science fiction and the process of 'producing' science, specifically theoretical physics. What are the ground rules for introducing unproven new ideas in science fiction, and how do they differ from the corresponding rules in physics? How predictive is science fiction? (For that matter, how predictive is theoretical physics?) I will also contrast the way in which information is presented in science fiction, as opposed to its presentation in scientific papers, and I will examine the relative importance of ideas (as opposed to the importance of the way in which these ideas are presented). Finally, I will discuss whether a background as a research scientist provides any advantage in writing science fiction.

Processing conditions for producing french fries from purple-fleshed sweetpotatoes

USDA-ARS?s Scientific Manuscript database

The effects of processing conditions and cooking methods on the physical quality, anthocyanin content and sensory attributes of frozen purple-fleshed sweetpotato (PFSP) French fries were investigated. PFSP strips were blanched in boiling water for 0, 5 or 10 min, par-fried at 180ºC for 0 or 1 min an...

Speaking and Speaking Education as Physical Process in Turkish Education

ERIC Educational Resources Information Center

Kurudayioglu, Mehmet

2011-01-01

Speaking is sending the message which is desired to be transferred to another one with vocal organs and produced by complicated operations in the brain. Speaking, which is a complicated process, is the most common and important means of communication among people. Speaking, which has essential place both individually and socially, affects success…

Focused Ion Beam Microscopy of ALH84001 Carbonate Disks

NASA Technical Reports Server (NTRS)

Thomas-Keprta, Kathie L.; Clemett, Simon J.; Bazylinski, Dennis A.; Kirschvink, Joseph L.; McKay, David S.; Vali, Hojatollah; Gibson, Everett K., Jr.; Romanek, Christopher S.

2005-01-01

Our aim is to understand the mechanism(s) of formation of carbonate assemblages in ALH84001. A prerequisite is that a detailed characterization of the chemical and physical properties of the carbonate be established. We present here analyses by transmission electron microscopy (TEM) of carbonate thin sections produced by both focused ion beam (FIB) sectioning and ultramicrotomy. Our results suggest that the formation of ALH84001 carbonate assemblages were produced by considerably more complex process(es) than simple aqueous precipitation followed by partial thermal decomposition as proposed by other investigators [e.g., 1-3].

Final Technical Report: Magnetic Reconnection in High-Energy Laser-Produced Plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Germaschewski, Kai; Fox, William; Bhattacharjee, Amitava

This report describes the final results from the DOE Grant DE-SC0007168, “Fast Magnetic Reconnection in HED Laser-Produced Plasmas.” The recent generation of laboratory high-energy-density physics facilities has opened significant physics opportunities for experimentally modeling astrophysical plasmas. The goal of this proposal is to use these new tools to study fundamental problems in plasma physics and plasma astrophysics. Fundamental topics in this area involve study of the generation, amplification, and fate of magnetic fields, which are observed to pervade the plasma universe and govern its evolution. This project combined experiments at DOE laser facilities with kinetic plasma simulation to study thesemore » processes. The primary original goal of the project was to study magnetic reconnection using a new experimental platform, colliding magnetized laser-produced plasmas. However through a series of fortuitous discoveries, the work broadened out to allow significant advancement on multiple topics in laboratory astrophysics, including magnetic reconnection, Weibel instability, and collisionless shocks.« less

3D freeform printing of silk fibroin.

PubMed

Rodriguez, Maria J; Dixon, Thomas A; Cohen, Eliad; Huang, Wenwen; Omenetto, Fiorenzo G; Kaplan, David L

2018-04-15

Freeform fabrication has emerged as a key direction in printing biologically-relevant materials and structures. With this emerging technology, complex structures with microscale resolution can be created in arbitrary geometries and without the limitations found in traditional bottom-up or top-down additive manufacturing methods. Recent advances in freeform printing have used the physical properties of microparticle-based granular gels as a medium for the submerged extrusion of bioinks. However, most of these techniques require post-processing or crosslinking for the removal of the printed structures (Miller et al., 2015; Jin et al., 2016) [1,2]. In this communication, we introduce a novel method for the one-step gelation of silk fibroin within a suspension of synthetic nanoclay (Laponite) and polyethylene glycol (PEG). Silk fibroin has been used as a biopolymer for bioprinting in several contexts, but chemical or enzymatic additives or bulking agents are needed to stabilize 3D structures. Our method requires no post-processing of printed structures and allows for in situ physical crosslinking of pure aqueous silk fibroin into arbitrary geometries produced through freeform 3D printing. 3D bioprinting has emerged as a technology that can produce biologically relevant structures in defined geometries with microscale resolution. Techniques for fabrication of free-standing structures by printing into granular gel media has been demonstrated previously, however, these methods require crosslinking agents and post-processing steps on printed structures. Our method utilizes one-step gelation of silk fibroin within a suspension of synthetic nanoclay (Laponite), with no need for additional crosslinking compounds or post processing of the material. This new method allows for in situ physical crosslinking of pure aqueous silk fibroin into defined geometries produced through freeform 3D printing. Copyright © 2018 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

iMAST FY2003 Annual Report

DTIC Science & Technology

2003-01-01

The approach being pursued, under this program structure, is to eliminate the use of physical surfaces on the component as datum. The use of physical...will eliminate /minimize fretting and low-cycle fatigue and the blade-disk interface. This optimum coating and/or coating process will be evaluated both...Utilizes MCLB infrastructure Avoids costs associated with existing APCS Biofiltration produces no secondary emissions Biofiltration is the most

Non- contacting capacitive diagnostic device

DOEpatents

Ellison, Timothy

2005-07-12

A non-contacting capacitive diagnostic device includes a pulsed light source for producing an electric field in a semiconductor or photovoltaic device or material to be evaluated and a circuit responsive to the electric field. The circuit is not in physical contact with the device or material being evaluated and produces an electrical signal characteristic of the electric field produced in the device or material. The diagnostic device permits quality control and evaluation of semiconductor or photovoltaic device properties in continuous manufacturing processes.

Improved collagen extraction from jellyfish (Acromitus hardenbergi) with increased physical-induced solubilization processes.

PubMed

Khong, Nicholas M H; Yusoff, Fatimah Md; Jamilah, B; Basri, Mahiran; Maznah, I; Chan, Kim Wei; Armania, Nurdin; Nishikawa, Jun

2018-06-15

Efficiency and effectiveness of collagen extraction process contribute to huge impacts to the quality, supply and cost of the collagen produced. Jellyfish is a potential sustainable source of collagen where their applications are not limited by religious constraints and threats of transmittable diseases. The present study compared the extraction yield, physico-chemical properties and toxicology in vitro of collagens obtained by the conventional acid-assisted and pepsin-assisted extraction to an improved physical-aided extraction process. By increasing physical intervention, the production yield increased significantly compared to the conventional extraction processes (p < .05). Collagen extracted using the improved process was found to possess similar proximate and amino acids composition to those extracted using pepsin (p > .05) while retaining high molecular weight distributions and polypeptide profiles similar to those extracted using only acid. Moreover, they exhibited better appearance, instrumental colour and were found to be non-toxic in vitro and free of heavy metal contamination. Copyright © 2017 Elsevier Ltd. All rights reserved.

Re-accumulation of Asteroids to Equilibrium Figures

NASA Astrophysics Data System (ADS)

Hestroffer, D.; Tanga, P.; Richardson, D. C.; Berthier, J.; Cellino, A.; Durech, J.; Michel, P.

2008-09-01

Since their formation, asteroids since their formation have experienced little physical, geological or thermal evolution. Like comets they are thought to be among the most pristine remnants of the early solar system. One physical process, however, has played a major role since the ancient times: collisions. Dynamical families were produced by catastrophic collisions involving large enough energy to break the parent body. Other lines of evidence suggest that catastrophic collisions can also produce rubble-piles, i.e., loosely bound of post-collisional aggregates that re-accumulate to form a single body, and are kept together by gravity. The main objective of this work is to understand if—and under what conditions—Jacobi ellipsoids or other equilibrium figures can be obtained naturally by this way. This is done by performing numerical experiments simulating the re-accumulation process, and by performing high-angular resolution observations in order to better constrain the shape and density of the targets. It is shown that the outcomes of reaccumulation events tend to produce a rather narrow variety of possible shapes, and in some cases also binary systems.

Towards a Marriage of Two Minds: The Word Processor and Natural Habits of Thought in the "Discovery" Stage of Composing.

ERIC Educational Resources Information Center

Aschauer, Mary Ann; White, Fred D.

Word processing programs offer five capabilities that can help students over the physical and psychological constraints associated with writing. First, producing text on a word processor is more tentative and more noncommital than producing text on paper. This reassures the writer that it is all right to experiment with words. Second, the blinking…

AUTO-EXPANSIVE FLOW

EPA Science Inventory

Physics suggests that the interplay of momentum, continuity, and geometry in outward radial flow must produce density and concomitant pressure reductions. In other words, this flow is intrinsically auto-expansive. It has been proposed that this process is the key to understanding...

Numerical simulations for active tectonic processes: increasing interoperability and performance

NASA Technical Reports Server (NTRS)

Donnellan, A.; Fox, G.; Rundle, J.; McLeod, D.; Tullis, T.; Grant, L.

2002-01-01

The objective of this project is to produce a system to fully model earthquake-related data. This task develops simulation and analysis tools to study the physics of earthquakes using state-of-the-art modeling.

Towards a turbulent magnetic dysnamo platform

NASA Astrophysics Data System (ADS)

Flippo, Kirk; Rasmus, Alexander; Li, Hui; Li, Shengtai; Kuranz, Carolyn; Levesque, Joseph; Klein, Sallee; Tzeferacos, Petros

2017-10-01

It is known through astronomical observations that most of the Universe is ionized, magnetized, and often turbulent and filled with jets. One theorized process to create strong magnetic fields and jets is the turbulent magnetic dynamo. The magnetic dynamo is a fundamental process in plasma physics, taking kinetic energy and converting it to magnetic energy and is very important to planetary physics and astrophysics. We report on recent Omega EP experiments to produce platform with a turbulent plume of magnetized material with which to study the turbulent magnetic dynamo process. The laser interaction with the target can seed magnetic fields that can be advected into the plume and amplified to saturation by the turbulent magnetic dynamo process. The experimentally measured plume characteristics are compared to hydro code calculations.

The effects of physical activity on impulsive choice: Influence of sensitivity to reinforcement amount and delay.

PubMed

Strickland, Justin C; Feinstein, Max A; Lacy, Ryan T; Smith, Mark A

2016-05-01

Impulsive choice is a diagnostic feature and/or complicating factor for several psychological disorders and may be examined in the laboratory using delay-discounting procedures. Recent investigators have proposed using quantitative measures of analysis to examine the behavioral processes contributing to impulsive choice. The purpose of this study was to examine the effects of physical activity (i.e., wheel running) on impulsive choice in a single-response, discrete-trial procedure using two quantitative methods of analysis. To this end, rats were assigned to physical activity or sedentary groups and trained to respond in a delay-discounting procedure. In this procedure, one lever always produced one food pellet immediately, whereas a second lever produced three food pellets after a 0, 10, 20, 40, or 80-s delay. Estimates of sensitivity to reinforcement amount and sensitivity to reinforcement delay were determined using (1) a simple linear analysis and (2) an analysis of logarithmically transformed response ratios. Both analyses revealed that physical activity decreased sensitivity to reinforcement amount and sensitivity to reinforcement delay. These findings indicate that (1) physical activity has significant but functionally opposing effects on the behavioral processes that contribute to impulsive choice and (2) both quantitative methods of analysis are appropriate for use in single-response, discrete-trial procedures. Copyright © 2016 Elsevier B.V. All rights reserved.

A Simple Rate Law Experiment Using a Custom-Built Isothermal Heat Conduction Calorimeter

ERIC Educational Resources Information Center

Wadso, Lars; Li, Xi.

2008-01-01

Most processes (whether physical, chemical, or biological) produce or consume heat: measuring thermal power (the heat production rate) is therefore a typical method of studying processes. Here we describe the design of a simple isothermal heat conduction calorimeter built for use in teaching; we also provide an example of its use in simultaneously…

Needed: A Standard Information Processing Model of Learning and Learning Processes.

ERIC Educational Resources Information Center

Carifio, James

One strategy to prevent confusion as new paradigms emerge is to have professionals in the area develop and use a standard model of the phenomenon in question. The development and use of standard models in physics, genetics, archaeology, and cosmology have been very productive. The cognitive revolution in psychology and education has produced a…

Hard diffraction and deep inelastic scattering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bjorken, J.D.

1994-04-01

Since the advent of hard-collision physics, the study of diffractive processes - shadow physics - has been less prominent than before. However, there is now a renewed interest in the subject, especially in that aspect which synthesizes the short-distance, hard-collision phenomena with the classical physics of large rapidity-gaps. This is especially stimulated by the recent data on deep-inelastic scattering from HERA, as well as the theoretical work which relates to it. The word diffraction is sometimes used by high-energy physicists in a loose way. The author defines this term to mean: A diffractive process occurs if and only if theremore » is a large rapidity gap in the produced-particle phase space which is not exponentially suppressed. Here a rapidity gap means essentially no hadrons produced into the rapidity gap (which operates in the {open_quotes}lego{close_quotes} phase-space of pseudo-rapidity and azimuthal angle). And non-exponential suppression implies that the cross-section for creating a gap with width {Delta}{eta} does not have a power-law decrease with increasing subenergy s=e{sup {Delta}{eta}}, but behaves at most like some power of pseudorapidity {Delta}{eta}{approx}log(s). The term hard diffraction shall simply refer to those diffractive process which have jets in the final-state phase-space.« less

The effect of colouring agent on the physical properties of glass ceramic produced from waste glass for antimicrobial coating deposition

NASA Astrophysics Data System (ADS)

Juoi, J. M.; Ayoob, N. F.; Rosli, Z. M.; Rosli, N. R.; Husain, K.

2016-07-01

Domestic waste glass is utilized as raw material for the production of glass ceramic material (GCM) via sinter crystallisation route. The glass ceramic material in a form of tiles is to be utilized for the deposition of Ag-TiO2 antimicrobial coating. Two types of soda lime glass (SLG) that are non-coloured and green SLG are utilised as main raw materials during the batch formulation in order to study the effect of colouring agent (Fe2O3) on the physical and mechanical properties of glass ceramic produced. Glass powder were prepared by crushing bottles using hammer milled with milling machine and sieved until they passed through 75 µm sieve. The process continues by mixing glass powder with ball clay with ratio of 95:5 wt. %, 90:10 wt. % and 85:15 wt. %. Each batch mixture was then uniaxial pressed and sintered at 800°C, 825 °C and 850 °C. The physical and mechanical properties were then determined and compared between those produced from non-coloured and green coloured SLG in order to evaluate the effect of colouring agent (Fe2O3) on the GCM produced. The optimum properties of non-coloured SLG is produced with smaller ball clay content (10 wt. %) compared to green SLG (15 wt. %). The physical properties (determined thru ASTM C373) of the optimized GCM produced from non-coloured SLG and green SLG are 0.69 % of porosity, 1.92 g/cm3 of bulk density, 0.36 % of water absorption; and 1.96 % of porosity, 2.69 g/cm3 of bulk density, 0.73 % of water absorption; respectively. Results also indicate that the most suitable temperature in producing GCM from both glasses with optimized physical and mechanical properties is at 850 °C.

Planning Model of Physics Learning In Senior High School To Develop Problem Solving Creativity Based On National Standard Of Education

NASA Astrophysics Data System (ADS)

Putra, A.; Masril, M.; Yurnetti, Y.

2018-04-01

One of the causes of low achievement of student’s competence in physics learning in high school is the process which they have not been able to develop student’s creativity in problem solving. This is shown that the teacher’s learning plan is not accordance with the National Eduction Standard. This study aims to produce a reconstruction model of physics learning that fullfil the competency standards, content standards, and assessment standards in accordance with applicable curriculum standards. The development process follows: Needs analysis, product design, product development, implementation, and product evaluation. The research process involves 2 peers judgment, 4 experts judgment and two study groups of high school students in Padang. The data obtained, in the form of qualitative and quantitative data that collected through documentation, observation, questionnaires, and tests. The result of this research up to the product development stage that obtained the physics learning plan model that meets the validity of the content and the validity of the construction in terms of the fulfillment of Basic Competence, Content Standards, Process Standards and Assessment Standards.

Science and Science Fiction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scherrer, Robert

2006-03-29

I will explore the similarities and differences between the process of writing science fiction and the process of 'producing' science, specifically theoretical physics. What are the ground rules for introducing unproven new ideas in science fiction, and how do they differ from the corresponding rules in physics? How predictive is science fiction? (For that matter, how predictive is theoretical physics?) I will also contrast the way in which information is presented in science fiction, as opposed to its presentation in scientific papers, and I will examine the relative importance of ideas (as opposed to the importance of the way inmore » which these ideas are presented). Finally, I will discuss whether a background as a research scientist provides any advantage in writing science fiction.« less

Nanostructured materials: A novel approach to enhanced performance. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korth, G.E.; Froes, F.H.; Suryanarayana, C.

Nanostuctured materials are an emerging class of materials that can exhibit physical and mechanical characteristics often exceeding those exhibited by conventional course grained materials. A number of different techniques can be employed to produce these materials. In this program, the synthesis methods were (a) mechanical alloying , (b) physical vapor deposition, and (c) plasma processing. The physical vapor deposition and plasma processing were discontinued after initial testing with subsequent efforts focused on mechanical alloying. The major emphasis of the program was on the synthesis, consolidation, and characterization of nanostructured Al-Fe, Ti-Al, Ti-Al-Nb, and Fe-Al by alloying intermetallics with a viewmore » to increase their ductilities. The major findings of this project are reported.« less

Need for improvements in physical pretreatment of source-separated household food waste.

PubMed

Bernstad, A; Malmquist, L; Truedsson, C; la Cour Jansen, J

2013-03-01

The aim of the present study was to investigate the efficiency in physical pretreatment processes of source-separated solid organic household waste. The investigation of seventeen Swedish full-scale pretreatment facilities, currently receiving separately collected food waste from household for subsequent anaerobic digestion, shows that problems with the quality of produced biomass and high maintenance costs are common. Four full-scale physical pretreatment plants, three using screwpress technology and one using dispergation technology, were compared in relation to resource efficiency, losses of nitrogen and potential methane production from biodegradable matter as well as the ratio of unwanted materials in produced biomass intended for wet anaerobic digestion. Refuse generated in the processes represent 13-39% of TS in incoming wet waste. The methane yield from these fractions corresponds to 14-36Nm(3)/ton separately collected solid organic household waste. Also, 13-32% of N-tot in incoming food waste is found in refuse. Losses of both biodegradable material and nutrients were larger in the three facilities using screwpress technology compared to the facility using dispersion technology.(1) Thus, there are large potentials for increase of both the methane yield and nutrient recovery from separately collected solid organic household waste through increased efficiency in facilities for physical pretreatment. Improved pretreatment processes could thereby increase the overall environmental benefits from anaerobic digestion as a treatment alternative for solid organic household waste. Copyright © 2012 Elsevier Ltd. All rights reserved.

Foam generator and viscometer apparatus and process

DOEpatents

Reed, Troy D.; Pickell, Mark B.; Volk, Leonard J.

2004-10-26

An apparatus and process to generate a liquid-gas-surfactant foam and to measure its viscosity and enable optical and or electronic measurements of physical properties. The process includes the steps of pumping selected and measured liquids and measured gases into a mixing cell. The mixing cell is pressurized to a desired pressure and maintained at a desired pressure. Liquids and gas are mixed in the mixing cell to produce a foam of desired consistency. The temperature of the foam in the mixing cell is controlled. Foam is delivered from the mixing cell through a viscometer under controlled pressure and temperature conditions where the viscous and physical properties of the foam are measured and observed.

Alternative Fuels Data Center: Renewable Hydrocarbon Biofuels

Science.gov Websites

, biodiesel is a mono-alkyl ester, which has different physical properties and hence different fuel specifications (ASTM D6751 and EN 14214). The two fuels are also produced through very different processes. While

Technology Of Controlled-Environment Agriculture

NASA Technical Reports Server (NTRS)

Bubenheim, David L.; Bates, Maynard E.

1995-01-01

Report discusses controlled-environment agriculture (CEA) for commercial production of organisms, whether plants or animals. Practiced in greenhouses to produce food on nonarable lands. Describes conceptual regenerative system that incorporates biological, physical, and chemical processes to support humans in extraterrestrial environments.

Optimum processing of mammographic film.

PubMed

Sprawls, P; Kitts, E L

1996-03-01

Underprocessing of mammographic film can result in reduced contrast and visibility of breast structures and an unnecessary increase in radiation dose to the patient. Underprocessing can be caused by physical factors (low developer temperature, inadequate development time, insufficient developer agitation) or chemical factors (developer not optimized for film type; overdiluted, underreplenished, contaminated, or frequently changed developer). Conventional quality control programs are designed to produce consistent processing but do not address the issue of optimum processing. Optimum processing is defined as the level of processing that produces the film performance characteristics (contrast and sensitivity) specified by the film manufacturer. Optimum processing of mammographic film can be achieved by following a two-step protocol. The first step is to set up the processing conditions according to recommendations from the film and developer chemistry manufacturers. The second step is to verify the processing results by comparing them with sensitometric data provided by the film manufacturer.

Effects of pore-scale physics on uranium geochemistry in Hanford sediments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Qinhong; Ewing, Robert P.

Overall, this work examines a key scientific issue, mass transfer limitations at the pore-scale, using both new instruments with high spatial resolution, and new conceptual and modeling paradigms. The complementary laboratory and numerical approaches connect pore-scale physics to macroscopic measurements, providing a previously elusive scale integration. This Exploratory research project produced five peer-reviewed journal publications and eleven scientific presentations. This work provides new scientific understanding, allowing the DOE to better incorporate coupled physical and chemical processes into decision making for environmental remediation and long-term stewardship.

An acoustic glottal source for vocal tract physical models

NASA Astrophysics Data System (ADS)

Hannukainen, Antti; Kuortti, Juha; Malinen, Jarmo; Ojalammi, Antti

2017-11-01

A sound source is proposed for the acoustic measurement of physical models of the human vocal tract. The physical models are produced by fast prototyping, based on magnetic resonance imaging during prolonged vowel production. The sound source, accompanied by custom signal processing algorithms, is used for two kinds of measurements from physical models of the vocal tract: (i) amplitude frequency response and resonant frequency measurements, and (ii) signal reconstructions at the source output according to a target pressure waveform with measurements at the mouth position. The proposed source and the software are validated by computational acoustics experiments and measurements on a physical model of the vocal tract corresponding to the vowels [] of a male speaker.

From quantum foundations to applications and back.

PubMed

Gisin, Nicolas; Fröwis, Florian

2018-07-13

Quantum non-locality has been an extremely fruitful subject of research, leading the scientific revolution towards quantum information science, in particular, to device-independent quantum information processing. We argue that the time is ripe to work on another basic problem in the foundations of quantum physics, the quantum measurement problem, which should produce good physics in theoretical, mathematical, experimental and applied physics. We briefly review how quantum non-locality contributed to physics (including some outstanding open problems) and suggest ways in which questions around macroscopic quantumness could equally contribute to all aspects of physics.This article is part of a discussion meeting issue 'Foundations of quantum mechanics and their impact on contemporary society'. © 2018 The Author(s).

The conversion of anaerobic digestion waste into biofuels via a novel Thermo-Catalytic Reforming process.

PubMed

Neumann, Johannes; Meyer, Johannes; Ouadi, Miloud; Apfelbacher, Andreas; Binder, Samir; Hornung, Andreas

2016-01-01

Producing energy from biomass and other organic waste residues is essential for sustainable development. Fraunhofer UMSICHT has developed a novel reactor which introduces the Thermo-Catalytic Reforming (TCR®) process. The TCR® is a process which can convert any type of biomass and organic feedstocks into a variety of energy products (char, bio-oil and permanent gases). The aim of this work was to demonstrate this technology using digestate as the feedstock and to quantify the results from the post reforming step. The temperature of a post reformer was varied to achieve optimised fuel products. The hydrogen rich permanent gases produced were maximised at a post reforming temperature of 1023 K. The highly de-oxygenated liquid bio-oil produced contained a calorific value of 35.2 MJ/kg, with significantly improved fuel physical properties, low viscosity and acid number. Overall digestate showed a high potential as feedstock in the Thermo-Catalytic Reforming to produce pyrolysis fuel products of superior quality. Copyright © 2015 Elsevier Ltd. All rights reserved.

Technique for forcing high Reynolds number isotropic turbulence in physical space

NASA Astrophysics Data System (ADS)

Palmore, John A.; Desjardins, Olivier

2018-03-01

Many common engineering problems involve the study of turbulence interaction with other physical processes. For many such physical processes, solutions are expressed most naturally in physical space, necessitating the use of physical space solutions. For simulating isotropic turbulence in physical space, linear forcing is a commonly used strategy because it produces realistic turbulence in an easy-to-implement formulation. However, the method resolves a smaller range of scales on the same mesh than spectral forcing. We propose an alternative approach for turbulence forcing in physical space that uses the low-pass filtered velocity field as the basis of the forcing term. This method is shown to double the range of scales captured by linear forcing while maintaining the flexibility and low computational cost of the original method. This translates to a 60% increase of the Taylor microscale Reynolds number on the same mesh. An extension is made to scalar mixing wherein a scalar field is forced to have an arbitrarily chosen, constant variance. Filtered linear forcing of the scalar field allows for control over the length scale of scalar injection, which could be important when simulating scalar mixing.

PYTHIA 6.4 Physics and Manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sjostrand, Torbjorn; /Lund U., Dept. Theor. Phys.; Mrenna, Stephen

2006-03-01

The Pythia program can be used to generate high-energy-physics ''events'', i.e. sets of outgoing particles produced in the interactions between two incoming particles. The objective is to provide as accurate as possible a representation of event properties in a wide range of reactions, within and beyond the Standard Model, with emphasis on those where strong interactions play a role, directly or indirectly, and therefore multihadronic final states are produced. The physics is then not understood well enough to give an exact description; instead the program has to be based on a combination of analytical results and various QCD-based models. Thismore » physics input is summarized here, for areas such as hard subprocesses, initial- and final-state parton showers, underlying events and beam remnants, fragmentation and decays, and much more. Furthermore, extensive information is provided on all program elements: subroutines and functions, switches and parameters, and particle and process data. This should allow the user to tailor the generation task to the topics of interest.« less

R&D 100, 2016: T-Quake – Quantum-Mechanical Transmitter/Receiver Microchip

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tauke-Pedretti, Anna; Camacho, Ryan; Thayer, Gayle

2016-11-07

Applying advanced microfabrication techniques and innovative microdesign, the Sandia Enabled Communications and Authentication Network (SECANT) team has designed and produced photonic microchips capable of sending, receiving, and processing quantum signals for applications in cyber and physical security.

Biocontrol interventions for inactivation of foodborne pathogens on produce

USDA-ARS?s Scientific Manuscript database

Post-harvest interventions for control of foodborne pathogens on minimally processed foods are crucial for food safety. Biocontrol interventions have the primary objective of developing novel antagonists in combinations with physical and chemical interventions to inactivate pathogenic microbes. Ther...

New experimental developments for s- and p-process research

NASA Astrophysics Data System (ADS)

Reifarth, R.; Ershova, O.; Glorius, J.; Göbel, K.; Langer, C.; Meusel, O.; Plag, R.; Schmidt, S.; Sonnabend, K.; Heil, M.

2012-12-01

Almost all of the heavy elements are produced via neutron-induced processes in a multitude of stellar production sites. The remaining minor part is produced via photon- and proton-induced reactions. The predictive power of the underlying stellar models is currently limited because they contain poorly constrained physics components such as convection, rotation or magnetic fields. An important tool to determine such components is the comparison of observed with modeled abundance distributions based on improved nuclear physics input. The FRANZ facility at the Goethe University Frankfurt, which is currently under construction will provide unprecedented neutron fluxes and proton currents available for nuclear astrophysics. It will be possible to investigate important branchpoint nuclei of the s-process nucleosynthesis path and proton-induced reactions important for p-process modeling. At the GSI close to Darmstadt radioactive isotopes can be investigated in inverse kinematics. This allows experiments such as proton-induced cross section measurements using a heavy-ion storage ring or measurements of gamma-induced reactions using the Coulomb dissociation method. The future FAIR facility will allow similar experiments on very exotic nuclei, since orders of magnitude higher radioactive ions beams will be possible.

Making data matter: Voxel printing for the digital fabrication of data across scales and domains.

PubMed

Bader, Christoph; Kolb, Dominik; Weaver, James C; Sharma, Sunanda; Hosny, Ahmed; Costa, João; Oxman, Neri

2018-05-01

We present a multimaterial voxel-printing method that enables the physical visualization of data sets commonly associated with scientific imaging. Leveraging voxel-based control of multimaterial three-dimensional (3D) printing, our method enables additive manufacturing of discontinuous data types such as point cloud data, curve and graph data, image-based data, and volumetric data. By converting data sets into dithered material deposition descriptions, through modifications to rasterization processes, we demonstrate that data sets frequently visualized on screen can be converted into physical, materially heterogeneous objects. Our approach alleviates the need to postprocess data sets to boundary representations, preventing alteration of data and loss of information in the produced physicalizations. Therefore, it bridges the gap between digital information representation and physical material composition. We evaluate the visual characteristics and features of our method, assess its relevance and applicability in the production of physical visualizations, and detail the conversion of data sets for multimaterial 3D printing. We conclude with exemplary 3D-printed data sets produced by our method pointing toward potential applications across scales, disciplines, and problem domains.

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.K. Kawatra; B. Anamerie; T.C. Eisele

The pig iron nugget process was developed as an alternative to the traditional blast furnace process by Kobe Steel. The process aimed to produce pig iron nuggets, which have similar chemical and physical properties to blast furnace pig iron, in a single step. The pig iron nugget process utilizes coal instead of coke and self reducing and fluxing dried green balls instead of pellets and sinters. In this process the environmental emissions caused by coke and sinter production, and energy lost between pellet induration (heat hardening) and transportation to the blast furnace can be eliminated. The objectives of this researchmore » were to (1) produce pig iron nuggets in the laboratory, (2) characterize the pig iron nugget produced and compare them with blast furnace pig iron, (3) investigate the furnace temperature and residence time effects on the pig iron nugget production, and (4) optimize the operational furnace temperatures and residence times. The experiments involved heat treatment of self reducing and fluxing dried green balls at various furnace temperatures and residence times. Three chemically and physically different products were produced after the compete reduction of iron oxides to iron depending on the operational furnace temperatures and/or residence times. These products were direct reduced iron (DRI), transition direct reduced iron (TDRI), and pig iron nuggets. The increase in the carbon content of the system as a function of furnace temperature and/or residence time dictated the formation of these products. The direct reduced iron, transition direct reduced iron, and pig iron nuggets produced were analyzed for their chemical composition, degree of metallization, apparent density, microstructure and microhardness. In addition, the change in the carbon content of the system with the changing furnace temperature and/or residence time was detected by optical microscopy and Microhardness measurements. The sufficient carbon dissolution required for the production of pig iron nuggets was determined. It was determined that pig iron nuggets produced had a high apparent density (6.7-7.2 gr/cm3), highly metallized, slag free structure, high iron content (95-97%), high microhardness values (> 325 HVN) and microstructure similar to white cast iron. These properties made them a competitive alternative to blast furnace pig iron.« less

Tangent linear super-parameterization: attributable, decomposable moist processes for tropical variability studies

NASA Astrophysics Data System (ADS)

Mapes, B. E.; Kelly, P.; Song, S.; Hu, I. K.; Kuang, Z.

2015-12-01

An economical 10-layer global primitive equation solver is driven by time-independent forcing terms, derived from a training process, to produce a realisting eddying basic state with a tracer q trained to act like water vapor mixing ratio. Within this basic state, linearized anomaly moist physics in the column are applied in the form of a 20x20 matrix. The control matrix was derived from the results of Kuang (2010, 2012) who fitted a linear response function from a cloud resolving model in a state of deep convecting equilibrium. By editing this matrix in physical space and eigenspace, scaling and clipping its action, and optionally adding terms for processes that do not conserve moist statice energy (radiation, surface fluxes), we can decompose and explain the model's diverse moist process coupled variability. Recitified effects of this variability on the general circulation and climate, even in strictly zero-mean centered anomaly physic cases, also are sometimes surprising.

[Urban culture and physical and sports activities. The "sportification" of parkour and street golf as cultural mediation].

PubMed

Lebreton, Florian; Routier, Guillaume; Héas, Stephane; Bodin, Dominique

2010-08-01

The article explores the process of "sportification"--i.e., processing physical activity in a sport regulated by a set of rules and standards, legitimized by supervisory institutions--from two originals practices, parkour and urban golf. To study these practices, we crossed the contributions of urban sociology and of the contemporary sociology of sport while respecting the methodological principles of qualitative sociology. A first point concerns the process of"sport" itself, its definition, its various stages, and the role played by communication of stakeholders on public space. The cultural mediation shows us how to institutionalize the movement that represents the "sports" resulted in the same time reconfiguration of physical practices themselves. Recent events illustrate the ongoing reconfiguration, we will detail them. Finally, we show the effects produced by the process on the definition of urban culture and sports: setting sight of activities, enhanced cooperation with the media-cultural, polarization between different types of practical in the case of parkour, around a confrontation between two of the founders.

Towards engineered branch placement: Unreal™ match between vapour-liquid-solid glancing angle deposition nanowire growth and simulation

NASA Astrophysics Data System (ADS)

Taschuk, M. T.; Tucker, R. T.; LaForge, J. M.; Beaudry, A. L.; Kupsta, M. R.; Brett, M. J.

2013-12-01

The vapour-liquid-solid glancing angle deposition (VLS-GLAD) process is capable of producing complex nanotree structures with control over azimuthal branch orientation and height. We have developed a thin film growth simulation including ballistic deposition, simplified surface diffusion, and droplet-mediated cubic crystal growth for the VLS-GLAD process using the UnrealTM Development Kit. The use of a commercial game engine has provided an interactive environment while allowing a custom physics implementation. Our simulation's output is verified against experimental data, including a volumetric film reconstruction produced using focused ion beam and scanning-electron microscopy (SEM), crystallographic texture, and morphological characteristics such as branch orientation. We achieve excellent morphological and texture agreement with experimental data, as well as qualitative agreement with SEM imagery. The simplified physics in our model reproduces the experimental films, indicating that the dominant role flux geometry plays in the VLS-GLAD competitive growth process responsible for azimuthally oriented branches and biaxial crystal texture evolution. The simulation's successful reproduction of experimental data indicates that it should have predictive power in designing novel VLS-GLAD structures.

Physical and material properties of an emulsion-based lipstick produced via a continuous process.

PubMed

Beri, A; Pichot, R; Norton, I T

2014-04-01

Water-in-oil emulsions in lipsticks could have the potential to improve moisturizing properties and deliver hydrophilic molecules to the lips. The aim of this work was to investigate the effect of a continuous process (scraped surface heat exchanger (SSHE) and pin stirrer (PS)) on the physical and material properties of an emulsion-based lipstick by altering the processing conditions of both the SSHE and PS. Emulsion formation was achieved using a SSHE and PS. Emulsions were analysed using nuclear magnetic resonance restricted diffusion (droplet size), texture analysis and rheology (mechanical properties). Results showed that a higher impeller rotational velocity (IRV) (1500 r.p.m.) and a lower exit temperature (52°C) produce the smallest droplets (~ 4 μm), due to greater disruptive forces and a higher viscosity of the continuous phase. The addition of a PS reduces the droplet size (14-6 μm) if the SSHE has a low IRV (500 r.p.m.), due to greater droplet disruption as the emulsion passes through the PS unit. Results also show that if the jacket temperature of a SSHE is 65°C, so that crystallization occurs in both process and post-production, droplets can be integrated into the network resulting in a stiffer wax network (G' - 0.12, in comparison to 0.02 MPa). This is due to small crystals creating a shell around water droplets which can form connections with the continuous network forming a structured network. The addition of a pin stirrer can disrupt a formed network reducing the stiffness of the emulsion (0.3-0.05 MPa). This work suggests the potential use of a continuous process in producing an emulsion-based lipstick, particularly when wax crystals are produced in the process. Future work should consider the moisturizing or lubricating properties of wax continuous emulsions and the release of hydrophilic compounds from the aqueous phase.

Toxicology and occupational hazards of new materials and processes in metal surface treatment, powder metallurgy, technical ceramics, and fiber-reinforced plastics.

PubMed

Midtgård, U; Jelnes, J E

1991-12-01

Many new materials and processes are about to find their way from the research laboratory into industry. The present paper describes some of these processes and provides an overview of possible occupational hazards and a list of chemicals used or produced in the processes. The technological areas that are considered are metal surface treatment (ion implantation, physical and chemical vapor deposition, plasma spraying), powder metallurgy, advanced technical ceramics, and fiber-reinforced plastics.

Postharvest treatments of fresh produce

PubMed Central

Mahajan, P. V.; Caleb, O. J.; Singh, Z.; Watkins, C. B.; Geyer, M.

2014-01-01

Postharvest technologies have allowed horticultural industries to meet the global demands of local and large-scale production and intercontinental distribution of fresh produce that have high nutritional and sensory quality. Harvested products are metabolically active, undergoing ripening and senescence processes that must be controlled to prolong postharvest quality. Inadequate management of these processes can result in major losses in nutritional and quality attributes, outbreaks of foodborne pathogens and financial loss for all players along the supply chain, from growers to consumers. Optimal postharvest treatments for fresh produce seek to slow down physiological processes of senescence and maturation, reduce/inhibit development of physiological disorders and minimize the risk of microbial growth and contamination. In addition to basic postharvest technologies of temperature management, an array of others have been developed including various physical (heat, irradiation and edible coatings), chemical (antimicrobials, antioxidants and anti-browning) and gaseous treatments. This article examines the current status on postharvest treatments of fresh produce and emerging technologies, such as plasma and ozone, that can be used to maintain quality, reduce losses and waste of fresh produce. It also highlights further research needed to increase our understanding of the dynamic response of fresh produce to various postharvest treatments. PMID:24797137

Development of the Oxford Hills Healthy Moms Project using a social marketing process: a community-based physical activity and nutrition intervention for low-socioeconomic-status mothers in a rural area in Maine.

PubMed

Dharod, Jigna M; Drewette-Card, Rebecca; Crawford, David

2011-03-01

A physical activity and nutrition community intervention called the Oxford Hills Healthy Moms (OHHM) Project was developed using a multifaceted social marketing process, including review of state surveillance results, key informant interviews, and a survey and focus group discussions with low-socioeconomic-status (low-SES) mothers. This formative work was used to make key decisions on the selection of the intervention region, segmentation of the audience, and design of intervention strategies addressing multiple levels of the socioecological model. The OHHM Project aims to increase fruit and vegetable consumption and physical activity levels among low-SES mothers in the Oxford Hills region of Maine. The OHHM Project includes five components: (a) physical activity buddy program, (b) cooking club with education, (c) fruit and vegetable discount buying club with education, (d) increased access to produce vendors, and (e) increased access to places for physical activity.

Search for new physics in events with photons, jets, and missing transverse energy in pp collisions at $$ \\sqrt{s}=7 $$ TeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chatrchyan, S.; Khachatryan, V.; Sirunyan, A. M.

A search for physics beyond the standard model involving events with one or more photons, jets, and missing transverse energy has been performed by the CMS experiment. The data sample corresponds to an integrated luminosity of 4.93 fb -1 of proton-proton collisions at TeV, produced at the Large Hadron Collider. No excess of events with large missing transverse energy is observed beyond expectations from standard model processes, and upper limits on the signal production cross sections for new physics processes are set at the 95% confidence level. The results of this search are interpreted in the context of three modelsmore » of new physics: a general model of gauge-mediated supersymmetry breaking, Simplified Models, and a theory involving universal extra dimensions. In the absence of evidence for new physics, exclusion regions are derived in the parameter spaces of the respective models.« less

Issues in Space Physics in Need of Reconnection with Laboratory Physics

NASA Astrophysics Data System (ADS)

Coppi, B.

2017-10-01

Predicted space observations, such as the ``foot'' in front of collisionless shocks or the occurrence of magnetic reconnection in the Earth`s magnetotail leading to auroral substorms, have highlighted the fruitful connection of laboratory and space plasma physics. The emergence of high energy astrophysics has then benefitted by the contribution of experiments devised for fusion research to the understanding of issues such as that of angular momentum transport processes that have a key role in allowing accretion of matter on a central object (e.g. black hole). The theory proposed for the occurrence of spontaneous rotation in toroidal plasmas was suggested by that developed for accretion. The particle density values, =1015 cm-3 that are estimated to be those of plasmas surrounding known galactic black holes have in fact been produced by the Alcator and other machines. Collective modes excited in the presence of high energy particle populations in laboratory plasmas (e.g. when the ``slide away'' regime has been produced) have found successful applications in space. Magnetic reconnection theory developments and the mode particle resonances associated with them have led to envision new processes for novel high energy particle acceleration. Sponsored in part by the U.S. DoE.

R&D 100, 2016: T-Quake – Quantum-Mechanical Transmitter/Receiver Microchip

ScienceCinema

Tauke-Pedretti, Anna; Camacho, Ryan; Thayer, Gayle

2018-06-13

Applying advanced microfabrication techniques and innovative microdesign, the Sandia Enabled Communications and Authentication Network (SECANT) team has designed and produced photonic microchips capable of sending, receiving, and processing quantum signals for applications in cyber and physical security.

The Role of Hot ISM in Galaxy Formation and Evolution

NASA Astrophysics Data System (ADS)

Ostriker, Jeremiah

2014-08-01

The cooling rate for hot gas in and around galaxies has a critical importance both in physically setting the basic mass scale for these massive, self-gravitating systems and as an observational tool for assessing formation models, by enabling the comparison between predicted and observed X-ray luminosities. Three classic papers in 1977 showed that it would be difficult for galaxies above a certain mass to cool on a dynamical timescale. That mass scale, in terms of fundamental physics is as follows: M ≃ [({Gm_p^2}/{hbar c})^{-2}({e^2}/{hbar c})^5({m_p}/{m_e})^{1/2}]m_{p} or roughly 10^{12} solar masses. Galaxies above this mass tend to be enveloped in the hot, X-ray emitting, gaseous halos familiar to Chandra observers and their predecessors. The outer parts of these gaseous halos are easily kept hot by SNI, dynamical in-fall of satellites and other processes, but the inner parts will repeatedly collapse into cooling flows, starbursts and AGN flare-ups. The thermal X-ray emission will be highly variable with this providing an important diagnostic for these physical processes. Also, normal cosmological inflow of gas onto massive galaxies can be shown to produce (absent feedback) more X-rays emission than is observed - providing yet another argument for feedback processes, which would reduce the ambient hot gas density. Finally, several postulated physical scenarios, such as gas rich ("wet") binary spiral mergers or thermal AGN feedback would produce X-ray emission far in excess of observational limits, again showing the power of X-ray observations as a critical diagnostic tool.

Chemical and Physical Interactions of Martian Surface Material

NASA Astrophysics Data System (ADS)

Bishop, J. L.

1999-09-01

A model of alteration and maturation of the Martian surface material is described involving both chemical and physical interactions. Physical processes involve distribution and mixing of the fine-grained soil particles across the surface and into the atmosphere. Chemical processes include reaction of sulfate, salt and oxidizing components of the soil particles; these agents in the soils deposited on rocks will chew through the rock minerals forming coatings and will bind surface soils together to form duricrust deposits. Formation of crystalline iron oxide/oxyhydroxide minerals through hydrothermal processes and of poorly crystalline and amorphous phases through palagonitic processes both contribute to formation of the soil particles. Chemical and physical alteration of these soil minerals and phases contribute to producing the chemical, magnetic and spectroscopic character of the Martian soil as observed by Mars Pathfinder and Mars Global Surveyor. Minerals such as maghemite/magnetite and jarosite/alunite have been observed in terrestrial volcanic soils near steam vents and may be important components of the Martian surface material. The spectroscopic properties of several terrestrial volcanic soils containing these minerals have been analyzed and evaluated in terms of the spectroscopic character of the surface material on Mars.

Topical applications of resonance internal conversion in laser produced plasma

NASA Astrophysics Data System (ADS)

Karpeshin, F. F.

2007-04-01

Physical aspects of resonance effects arising in plasma due to interactions of nuclei with the electrons are considered. Among them are resonance conversion (TEEN) and the reverse process of NEET. These processes are of great importance for pumping the excited nuclear states (isomers) and for accelerating their decay. Experiment is discussed on studying the unique 3.5-eV 229m Th nuclide.

Psychosocial mediators of change in physical activity in the Welsh national exercise referral scheme: secondary analysis of a randomised controlled trial.

PubMed

Littlecott, Hannah J; Moore, Graham F; Moore, Laurence; Murphy, Simon

2014-08-27

While an increasing number of randomised controlled trials report impacts of exercise referral schemes (ERS) on physical activity, few have investigated the mechanisms through which increases in physical activity are produced. This study examines whether a National Exercise Referral Scheme (NERS) in Wales is associated with improvements in autonomous motivation, self-efficacy and social support, and whether change in physical activity is mediated by change in these psychosocial processes. A pragmatic randomised controlled trial of NERS across 12 LHBs in Wales. Questionnaires measured demographic data and physical activity at baseline. Participants (N = 2160) with depression, anxiety or CHD risk factors were referred by health professionals and randomly assigned to control or intervention. At six months psychological process measures were collected by questionnaire. At 12 months physical activity was assessed by 7 Day PAR telephone interview. Regressions tested intervention effects on psychosocial variables, physical activity before and after adjusting for mediators and socio demographic patterning. Significant intervention effects were found for autonomous motivation and social support for exercise at 6 months. No intervention effect was observed for self-efficacy. The data are consistent with a hypothesis of partial mediation of the intervention effect by autonomous motivation. Analysis of moderators showed significant improvements in relative autonomy in all subgroups. The greatest improvements in autonomous motivation were observed among patients who were least active at baseline. The present study offered key insights into psychosocial processes of change in an exercise referral scheme, with effects on physical activity mediated by autonomous motivation. Findings support the use of self-determination theory as a framework for ERS. Further research is required to explain socio-demographic patterning in responses to ERS, with changes in motivation occurring among all sub-groups of participants, though not always leading to higher adherence or behavioural change. This highlights the importance of socio-ecological approaches to developing and evaluating behaviour change interventions, which consider factors beyond the individual, including conditions in which improved motivation does or does not produce behavioural change. ISRCTN47680448.

Physical and chemical characterization of waste wood derived biochars.

PubMed

Yargicoglu, Erin N; Sadasivam, Bala Yamini; Reddy, Krishna R; Spokas, Kurt

2015-02-01

Biochar, a solid byproduct generated during waste biomass pyrolysis or gasification in the absence (or near-absence) of oxygen, has recently garnered interest for both agricultural and environmental management purposes owing to its unique physicochemical properties. Favorable properties of biochar include its high surface area and porosity, and ability to adsorb a variety of compounds, including nutrients, organic contaminants, and some gases. Physical and chemical properties of biochars are dictated by the feedstock and production processes (pyrolysis or gasification temperature, conversion technology and pre- and post-treatment processes, if any), which vary widely across commercially produced biochars. In this study, several commercially available biochars derived from waste wood are characterized for physical and chemical properties that can signify their relevant environmental applications. Parameters characterized include: physical properties (particle size distribution, specific gravity, density, porosity, surface area), hydraulic properties (hydraulic conductivity and water holding capacity), and chemical and electrochemical properties (organic matter and organic carbon contents, pH, oxidation-reduction potential and electrical conductivity, zeta potential, carbon, nitrogen and hydrogen (CHN) elemental composition, polycyclic aromatic hydrocarbons (PAHs), heavy metals, and leachable PAHs and heavy metals). A wide range of fixed carbon (0-47.8%), volatile matter (28-74.1%), and ash contents (1.5-65.7%) were observed among tested biochars. A high variability in surface area (0.1-155.1g/m(2)) and PAH and heavy metal contents of the solid phase among commercially available biochars was also observed (0.7-83 mg kg(-1)), underscoring the importance of pre-screening biochars prior to application. Production conditions appear to dictate PAH content--with the highest PAHs observed in biochar produced via fast pyrolysis and lowest among the gasification-produced biochars. Copyright © 2014 Elsevier Ltd. All rights reserved.

Chemical Changes in Lipids Produced by Thermal Processing.

ERIC Educational Resources Information Center

Nawar, Wassef W.

1984-01-01

Describes heat effects on lipids, indicating that the chemical and physical changes that occur depend on the lipid's composition and conditions of treatment. Thermolytic and oxidation reactions, thermal/oxidative interaction of lipids with other food components and the chemistry of frying are considered. (JN)

SONOCHEMICAL DECHLORINATION OF HAZARDOUS WASTES IN AQUEOUS SYSTEMS. (R825513C004)

EPA Science Inventory

Physical processes resulting from ultrasonication of aqueous solutions and suspensions produce extreme conditions that can affect the chemistry of dissolved and suspended chemicals. The purpose of this work was to explore the use of sonochemistry in treating chlorinated chemic...

Preparation of cermets

DOEpatents

Morgan, Chester S.

1978-01-01

Cermets are produced by the process of forming a physical mixture of a ceramic powder material with an elemental metal precursor compound and by decomposing the elemental metal precursor compound within the mixture. The decomposition step may be carried out either prior to or during a forming and densification step.

Development, characterization and potential applications of edible film from seaweed (Kappaphycus alvarezii)

NASA Astrophysics Data System (ADS)

Moey, Siah Watt; Abdullah, Aminah; Ahmad, Ishak

2014-09-01

A new patent pending process is proposed in this study to produce edible film directly from seaweed (Kappaphycus alvarezii). Seaweed together with other ingredients had been used to produce the film through casting technique. Physical and mechanical tests were performed on the edible film to examine the thickness, colour, transparency, solubility, tensile strength, elongation at break, water permeability rate, oxygen permeability rate and surface morphology. The produced film was transparent, stretchable, sealable and have basic properties for applications in food, pharmaceutical, cosmetic, toiletries and also agricultural industries. Edible film was successfully developed directly from dry seaweed instead of using alginate and carrageenan. The edible film processing method developed in this research was easier and cheaper compared with the method by using alginate and carrageenan.

Internal processes affecting surfaces of low-density satellites - Ganymede and Callisto

NASA Technical Reports Server (NTRS)

Parmentier, E. M.; Head, J. W.

1979-01-01

Possible significant physical processes on low-density (icy) satellites, particularly Ganymede and Callisto, are outlined, and the relations of these interior processes to the formation and evolution of satellite surfaces are discussed. A variety of mechanisms is shown to lead to interior melting in early satellite history and a configuration characterized by a predominantly water ice lithosphere overlying a mantle containing liquid water. Physical processes capable of affecting the lithosphere of an ice-silicate body and thus creating observable surface features are assessed, including tectonic stresses from tidal deformation and volume changes, gravitational effects on density differences and water volcanism. The residence time of surface features on icy bodies produced by the outlined processes and by impact cratering is considered, and a tentative outline of the geologic history of Ganymede and Callisto is presented. Observations from Voyager and Galileo are expected to provide evidence on the evolution and geologic history of low-density satellites.

Characterization of modified zeolite as microbial immobilization media on POME anaerobic digestion

NASA Astrophysics Data System (ADS)

Cahyono, Rochim B.; Ismiyati, Sri; Ginting, Simparmin Br; Mellyanawaty, Melly; Budhijanto, Wiratni

2018-03-01

As the world’s biggest palm oil producer, Indonesia generates also huge amount of Palm Oil Mill Effluent (POME) wastewater and causes serious problem in environment. In conventional method, POME was converted into biogas using lagoon system which required extensive land area. Anaerobic Fluidized Bed Reactor (AFBR) proposes more effective biogas producing with smaller land area. In the proposed system, a immobilization media would be main factor for enhancing productivity. This research studied on characterization of Lampung natural zeolite as immobilization media in the AFBR system for POME treatment. Various activation method such as physical and chemical were attempted to create more suitable material which has larger surface area, pore size distribution as well as excellent surface structures. The physical method was applied by heating up the material till 400°C while HCl was used on the chemical activation. Based on the result, the chemical activation increased the surface area significantly into 71 m2/g compared to physical as well as original zeolite. The strong acid material was quite effective to enforce the impurities within zeolite pore structure compared to heating up the material. According to distribution data, the Lampung zeolite owned the pore size with the range of 3 – 5 μm which was mesopore material. The pore size was appropriate for immobilization media as it was smaller than size of biogas microbial. The XRD patterns verified that chemical activation could maintain the zeolite structure as the original. Obviously, the SEM photograph showed apparent structure and pore size on the modified zeolite using chemical method. The testing of modified zeolite on the batch system was done to evaluate the characterization process. The modified zeolite using chemical process resulted fast reduction of COD and stabilized the volatile fatty acid as the intermediate product of anaerobic digestion, especially in the beginning of the process. Therefore, the chemical activation process was most suitable to produce the immobilization media from Lampung natural zeolite for POME waste treatment

The tropical precipitation pickup threshold and clouds in a radiative convective equilibrium model: 2. Two-layer moisture

NASA Astrophysics Data System (ADS)

Igel, Matthew R.

2017-06-01

This paper complements Part 1 in which cloud processes of aggregated convection are examined in a large-domain radiative convective equilibrium simulation in order to uncover those responsible for a consistently observed, abrupt increase in mean precipitation at a column relative humidity value of approximately 77%. In Part 2, the focus is on how the transition is affected independently by total moisture above and below the base of the melting layer. When mean precipitation rates are examined as simultaneous functions of these two moisture layers, four distinct behaviors are observed. These four behaviors suggest unique, yet familiar, physical regimes in which (i) little rain is produced by infrequent clouds, (ii) shallow convection produces increasing warm rain with increasing low-level moisture, (iii) deep convection produces progressively heavier rain above the transition point with increasing total moisture, and (iv) deep stratiform cloud produces increasingly intense precipitation from melting for increasing upper level moisture. The independent thresholds separating regimes in upper and lower layer humidity are shown to result in the value of total column humidity at which a transition between clear air and deep convection, and therefore a pickup in precipitation, is possible. All four regimes force atmospheric columns toward the pickup value at 77% column humidity, but each does so through a unique set of physical processes. Layer moisture and microphysical budgets are analyzed and contrasted with column budgets.

Characterization of the mechanical and physical properties of TD-NiCr (Ni-20Cr-2ThO2) alloy sheet

NASA Technical Reports Server (NTRS)

Fritz, L. J.; Koster, W. P.; Taylor, R. E.

1973-01-01

Sheets of TD-NiCr processed using techniques developed to produce uniform material were tested to supply mechanical and physical property data. Two heats each of 0.025 and 0.051 cm thick sheet were tested. Mechanical properties evaluated included tensile, modulus of elasticity, Poisson's Ratio, compression, creep-rupture, creep strength, bearing strength, shear strength, sharp notch and fatigue strength. Test temperatures covered the range from ambient to 1589K. Physical properties were also studied as a function of temperature. The physical properties measured were thermal conductivity, linear thermal expansion, specific heat, total hemispherical emittance, thermal diffusivity, and electrical conductivity.

Characterization of process air emissions in automotive production plants.

PubMed

D'Arcy, J B; Dasch, J M; Gundrum, A B; Rivera, J L; Johnson, J H; Carlson, D H; Sutherland, J W

2016-01-01

During manufacturing, particles produced from industrial processes become airborne. These airborne emissions represent a challenge from an industrial hygiene and environmental standpoint. A study was undertaken to characterize the particles associated with a variety of manufacturing processes found in the auto industry. Air particulates were collected in five automotive plants covering ten manufacturing processes in the areas of casting, machining, heat treatment and assembly. Collection procedures provided information on air concentration, size distribution, and chemical composition of the airborne particulate matter for each process and insight into the physical and chemical processes that created those particles.

Nuclear Technology: Making Informed Decisions.

ERIC Educational Resources Information Center

Altshuler, Kenneth

1989-01-01

Discusses a unit on nuclear technology which is taught in a physics class. Explains the unit design, implementation process, demonstrations used, and topics of discussion that include light and optics, naturally and artificially produced sources of radioactivity, nuclear equations, isotopes and half-lives, and power-generating nuclear reactors.…

Energy regeneration model of self-consistent field of electron beams into electric power*

NASA Astrophysics Data System (ADS)

Kazmin, B. N.; Ryzhov, D. R.; Trifanov, I. V.; Snezhko, A. A.; Savelyeva, M. V.

2016-04-01

We consider physic-mathematical models of electric processes in electron beams, conversion of beam parameters into electric power values and their transformation into users’ electric power grid (onboard spacecraft network). We perform computer simulation validating high energy efficiency of the studied processes to be applied in the electric power technology to produce the power as well as electric power plants and propulsion installation in the spacecraft.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hensley, Jesse; Ruddy, Daniel A.; Schaidle, Joshua A.

Catalysts and processes designed to convert DME and/or methanol and hydrogen (H.sub.2) to desirable liquid fuels are described. These catalysts produce the fuels efficiently and with a high selectivity and yield, and reduce the formation of aromatic hydrocarbons by incorporating H.sub.2 into the products. Also described are process methods to further upgrade these fuels to higher molecular weight liquid fuel mixtures, which have physical properties comparable with current commercially used liquid fuels.

Development of a monolithic ferrite memory array

NASA Technical Reports Server (NTRS)

Heckler, C. H., Jr.; Bhiwandker, N. C.

1972-01-01

The results of the development and testing of ferrite monolithic memory arrays are presented. This development required the synthesis of ferrite materials having special magnetic and physical characteristics and the development of special processes; (1) for making flexible sheets (laminae) of the ferrite composition, (2) for embedding conductors in ferrite, and (3) bonding ferrite laminae together to form a monolithic structure. Major problems encountered in each of these areas and their solutions are discussed. Twenty-two full-size arrays were fabricated and fired during the development of these processes. The majority of these arrays were tested for their memory characteristics as well as for their physical characteristics and the results are presented. The arrays produced during this program meet the essential goals and demonstrate the feasibility of fabricating monolithic ferrite memory arrays by the processes developed.

Secondary Metabolites Produced during the Germination of Streptomyces coelicolor.

PubMed

Čihák, Matouš; Kameník, Zdeněk; Šmídová, Klára; Bergman, Natalie; Benada, Oldřich; Kofroňová, Olga; Petříčková, Kateřina; Bobek, Jan

2017-01-01

Spore awakening is a series of actions that starts with purely physical processes and continues via the launching of gene expression and metabolic activities, eventually achieving a vegetative phase of growth. In spore-forming microorganisms, the germination process is controlled by intra- and inter-species communication. However, in the Streptomyces clade, which is capable of developing a plethora of valuable compounds, the chemical signals produced during germination have not been systematically studied before. Our previously published data revealed that several secondary metabolite biosynthetic genes are expressed during germination. Therefore, we focus here on the secondary metabolite production during this developmental stage. Using high-performance liquid chromatography-mass spectrometry, we found that the sesquiterpenoid antibiotic albaflavenone, the polyketide germicidin A, and chalcone are produced during germination of the model streptomycete, S. coelicolor . Interestingly, the last two compounds revealed an inhibitory effect on the germination process. The secondary metabolites originating from the early stage of microbial growth may coordinate the development of the producer ( quorum sensing ) and/or play a role in competitive microflora repression ( quorum quenching ) in their nature environments.

Secondary Metabolites Produced during the Germination of Streptomyces coelicolor

PubMed Central

Čihák, Matouš; Kameník, Zdeněk; Šmídová, Klára; Bergman, Natalie; Benada, Oldřich; Kofroňová, Olga; Petříčková, Kateřina; Bobek, Jan

2017-01-01

Spore awakening is a series of actions that starts with purely physical processes and continues via the launching of gene expression and metabolic activities, eventually achieving a vegetative phase of growth. In spore-forming microorganisms, the germination process is controlled by intra- and inter-species communication. However, in the Streptomyces clade, which is capable of developing a plethora of valuable compounds, the chemical signals produced during germination have not been systematically studied before. Our previously published data revealed that several secondary metabolite biosynthetic genes are expressed during germination. Therefore, we focus here on the secondary metabolite production during this developmental stage. Using high-performance liquid chromatography-mass spectrometry, we found that the sesquiterpenoid antibiotic albaflavenone, the polyketide germicidin A, and chalcone are produced during germination of the model streptomycete, S. coelicolor. Interestingly, the last two compounds revealed an inhibitory effect on the germination process. The secondary metabolites originating from the early stage of microbial growth may coordinate the development of the producer (quorum sensing) and/or play a role in competitive microflora repression (quorum quenching) in their nature environments. PMID:29326665

Terminator field-aligned current system: A new finding from model-assimilated data set (MADS)

NASA Astrophysics Data System (ADS)

Zhu, L.; Schunk, R. W.; Scherliess, L.; Sojka, J. J.; Gardner, L. C.; Eccles, J. V.; Rice, D.

2013-12-01

Physics-based data assimilation models have been recognized by the space science community as the most accurate approach to specify and forecast the space weather of the solar-terrestrial environment. The model-assimilated data sets (MADS) produced by these models constitute an internally consistent time series of global three-dimensional fields whose accuracy can be estimated. Because of its internal consistency of physics and completeness of descriptions on the status of global systems, the MADS has also been a powerful tool to identify the systematic errors in measurements, reveal the missing physics in physical models, and discover the important dynamical physical processes that are inadequately observed or missed by measurements due to observational limitations. In the past years, we developed a data assimilation model for the high-latitude ionospheric plasma dynamics and electrodynamics. With a set of physical models, an ensemble Kalman filter, and the ingestion of data from multiple observations, the data assimilation model can produce a self-consistent time-series of the complete descriptions of the global high-latitude ionosphere, which includes the convection electric field, horizontal and field-aligned currents, conductivity, as well as 3-D plasma densities and temperatures, In this presentation, we will show a new field-aligned current system discovered from the analysis of the MADS produced by our data assimilation model. This new current system appears and develops near the ionospheric terminator. The dynamical features of this current system will be described and its connection to the active role of the ionosphere in the M-I coupling will be discussed.

Harnessing of radio frequency discharge for production of biologically compatible coatings for ophthalmology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdullin, I.Sh.; Bragin, V.E.; Bykanov, A.N.

Gas discharge plasma modification of polymer materials and metals is one of the known physical approaches for improving of materials biocompatibility in ophthalmology and surgery. The surface treatment in RF discharges can be effectively realized in the discharge afterglow and in the discharge region itself too. This modification method is more convenient and produces more uniform surfaces in comparison with other discharge types. The carried out experiments and published up to now results show that interaction of UV radiation, fluxes of ions, electrons and metastable particles with material`s surface changes chemical composition and surface structure. The exerting of these agentsmore » on the sample surface produces the following effects. There are processes of physical and plasma-chemical surface etching producing effective surface cleaning of different types of contaminations. It may be surface contaminations by hydrocarbons because of preliminary surface contacts with biological or physical bodies. It may be surface contaminations caused by characteristic properties of chemical technology too. There is a surface layer with thickness from some angstroms up to few hundreds of angstroms. The chemical content and structure of this layer is distinguished from the bulk polymer properties. The presence of such {open_quotes}technological{close_quotes} contaminations produces the layer of material substantially differing from the base polymer. The basic layer physical and chemical properties for example, gas permeation rate may substantially differ from the base polymer. Attempts to clean the surface from these contaminations by chemical methods (solutions) have not been successful and produced contaminations of more deep polymer layers. So the plasma cleaning is the most profitable method of polymer treatment for removing the surface contaminations. The improving of wettability occurs during this stage of treatment.« less

Title: SCOAP3: Explanation and Current Status

NASA Astrophysics Data System (ADS)

Marsteller, Matthew

The Sponsoring Consortium for Open Access Publishing in Particle Physics (SCOAP3) is a successful global partnership of libraries, funding agencies and research centers. SCOAP3 has negotiated with journal publishers on behalf of libraries and institutions from around the world to produce open access literature in particle physics journals that were previously published in a traditional subscription-based model. This presentation will provide an overview of the process, an update of its status and some intriguing research metrics that have emerged.

Improving atomic displacement and replacement calculations with physically realistic damage models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nordlund, Kai; Zinkle, Steven J.; Sand, Andrea E.

Atomic collision processes are fundamental to numerous advanced materials technologies such as electron microscopy, semiconductor processing and nuclear power generation. Extensive experimental and computer simulation studies over the past several decades provide the physical basis for understanding the atomic-scale processes occurring during primary displacement events. The current international standard for quantifying this energetic particle damage, the Norgett-Robinson-Torrens displacements per atom (NRT-dpa) model, has nowadays several well-known limitations. In particular, the number of radiation defects produced in energetic cascades in metals is only ~1/3 the NRT-dpa prediction, while the number of atoms involved in atomic mixing is about a factor ofmore » 30 larger than the dpa value. Here we propose two new complementary displacement production estimators (athermal recombination corrected dpa, arc-dpa) and atomic mixing (replacements per atom, rpa) functions that extend the NRT-dpa by providing more physically realistic descriptions of primary defect creation in materials and may become additional standard measures for radiation damage quantification.« less

Improving atomic displacement and replacement calculations with physically realistic damage models

DOE PAGES

Nordlund, Kai; Zinkle, Steven J.; Sand, Andrea E.; ...

2018-03-14

Atomic collision processes are fundamental to numerous advanced materials technologies such as electron microscopy, semiconductor processing and nuclear power generation. Extensive experimental and computer simulation studies over the past several decades provide the physical basis for understanding the atomic-scale processes occurring during primary displacement events. The current international standard for quantifying this energetic particle damage, the Norgett-Robinson-Torrens displacements per atom (NRT-dpa) model, has nowadays several well-known limitations. In particular, the number of radiation defects produced in energetic cascades in metals is only ~1/3 the NRT-dpa prediction, while the number of atoms involved in atomic mixing is about a factor ofmore » 30 larger than the dpa value. Here we propose two new complementary displacement production estimators (athermal recombination corrected dpa, arc-dpa) and atomic mixing (replacements per atom, rpa) functions that extend the NRT-dpa by providing more physically realistic descriptions of primary defect creation in materials and may become additional standard measures for radiation damage quantification.« less

Improving atomic displacement and replacement calculations with physically realistic damage models.

PubMed

Nordlund, Kai; Zinkle, Steven J; Sand, Andrea E; Granberg, Fredric; Averback, Robert S; Stoller, Roger; Suzudo, Tomoaki; Malerba, Lorenzo; Banhart, Florian; Weber, William J; Willaime, Francois; Dudarev, Sergei L; Simeone, David

2018-03-14

Atomic collision processes are fundamental to numerous advanced materials technologies such as electron microscopy, semiconductor processing and nuclear power generation. Extensive experimental and computer simulation studies over the past several decades provide the physical basis for understanding the atomic-scale processes occurring during primary displacement events. The current international standard for quantifying this energetic particle damage, the Norgett-Robinson-Torrens displacements per atom (NRT-dpa) model, has nowadays several well-known limitations. In particular, the number of radiation defects produced in energetic cascades in metals is only ~1/3 the NRT-dpa prediction, while the number of atoms involved in atomic mixing is about a factor of 30 larger than the dpa value. Here we propose two new complementary displacement production estimators (athermal recombination corrected dpa, arc-dpa) and atomic mixing (replacements per atom, rpa) functions that extend the NRT-dpa by providing more physically realistic descriptions of primary defect creation in materials and may become additional standard measures for radiation damage quantification.

Raman Spectroscopy of 3-D Printed Polymers

NASA Astrophysics Data System (ADS)

Espinoza, Vanessa; Wood, Erin; Hight Walker, Angela; Seppala, Jonathan; Kotula, Anthony

Additive manufacturing (AM) techniques, such as 3-D printing are becoming an innovative and efficient way to produce highly customized parts for applications ranging from automotive to biomedical. Polymer-based AM parts can be produced from a myriad of materials and processing conditions to enable application-specific products. However, bringing 3-D printing from prototype to production relies on understanding the effect of processing conditions on the final product. Raman spectroscopy is a powerful and non-destructive characterization technique that can assist in determining the chemical homogeneity and physical alignment of polymer chains in 3-D printed materials. Two polymers commonly used in 3-D printing, acrylonitrile butadiene styrene (ABS) and polycarbonate (PC), were investigated using 1- and 2-D hyperspectral Raman imaging. In the case of ABS, a complex thermoplastic, the homogeneity of the material through the weld zone was investigated by comparing Raman peaks from each of the three components. In order to investigate the effect of processing conditions on polymer chain alignment, polarized Raman spectroscopy was used. In particular, the print speed or shear rate and effect of strain on PC filaments was investigated with perpendicular and parallel polarizations. National Institute of Standards and Technology Gaithersburg, MD ; Society of Physics Students.

Spontaneous Charge Separation and Sublimation Processes are Ubiquitous in Nature and in Ionization Processes in Mass Spectrometry

NASA Astrophysics Data System (ADS)

Trimpin, Sarah; Lu, I.-Chung; Rauschenbach, Stephan; Hoang, Khoa; Wang, Beixi; Chubatyi, Nicholas D.; Zhang, Wen-Jing; Inutan, Ellen D.; Pophristic, Milan; Sidorenko, Alexander; McEwen, Charles N.

2018-02-01

Ionization processes have been discovered by which small and large as well as volatile and nonvolatile compounds are converted to gas-phase ions when associated with a matrix and exposed to sub-atmospheric pressure. Here, we discuss experiments further defining these simple and unexpected processes. Charge separation is found to be a common process for small molecule chemicals, solids and liquids, passed through an inlet tube from a higher to a lower pressure region, with and without heat applied. This charge separation process produces positively- and negatively-charged particles with widely different efficiencies depending on the compound and its physical state. Circumstantial evidence is presented suggesting that in the new ionization process, charged particles carry analyte into the gas phase, and desolvation of these particles produce the bare ions similar to electrospray ionization, except that solid particles appear likely to be involved. This mechanistic proposition is in agreement with previous theoretical work related to ion emission from ice.

Effects of food processing on food allergens.

PubMed

Sathe, Shridhar K; Sharma, Girdhari M

2009-08-01

Food allergies are on the rise in Western countries. With the food allergen labeling requirements in the US and EU, there is an interest in learning how food processing affects food allergens. Numerous foods are processed in different ways at home, in institutional settings, and in industry. Depending on the processing method and the food, partial or complete removal of the offending allergen may be possible as illustrated by reduction of peanut allergen in vitro IgE immunoreactivity upon soaking and blanching treatments. When the allergen is discretely located in a food, one may physically separate and remove it from the food. For example, lye peeling has been reported to produce hypoallergenic peach nectar. Protein denaturation and/or hydrolysis during food processing can be used to produce hypoallergenic products. This paper provides a short overview of basic principles of food processing followed by examples of their effects on food allergen stability. Reviewed literature suggests assessment of processing effects on clinically relevant reactivity of food allergens is warranted.

Social-Ecological, Motivational and Volitional Factors for Initiating and Maintaining Physical Activity in the Context of HIV

PubMed Central

Ley, Clemens; Barrio, María Rato; Leach, Lloyd

2015-01-01

Sport and exercise can have several health benefits for people living with HIV. These benefits can be achieved through different types of physical activity, adapting to disease progression, motivation and social-ecological options. However, physical activity levels and adherence to exercise are generally low in people living with HIV. At the same time, high drop-out rates in intervention studies are prevalent; even though they often entail more favourable conditions than interventions in the natural settings. Thus, in the framework of an intervention study, the present study aims to explore social-ecological, motivational and volitional correlates of South African women living with HIV with regard to physical activity and participation in a sport and exercise health promotion programme. The qualitative data was produced in the framework of a non-randomised pre-post intervention study that evaluated structure, processes and outcomes of a 10-week sport and exercise programme. All 25 participants of the programme were included in this analysis, independent of compliance. Data was produced through questionnaires, participatory group discussions, body image pictures, research diaries and individual semi-structured interviews. All participants lived in a low socioeconomic, disadvantaged setting. Hence, the psychological correlates are contextualised and social-ecological influences on perception and behaviour are discussed. The results show the importance of considering social-cultural and environmental influences on individual motives, perceptions and expectancies, the fear of disclosure and stigmatisation, sport and exercise-specific group dynamics and self-supporting processes. Opportunities and strategies to augment physical activity and participation in sport and exercise programmes in the context of HIV are discussed. PMID:26587078

Social-Ecological, Motivational and Volitional Factors for Initiating and Maintaining Physical Activity in the Context of HIV.

PubMed

Ley, Clemens; Barrio, María Rato; Leach, Lloyd

2015-01-01

Sport and exercise can have several health benefits for people living with HIV. These benefits can be achieved through different types of physical activity, adapting to disease progression, motivation and social-ecological options. However, physical activity levels and adherence to exercise are generally low in people living with HIV. At the same time, high drop-out rates in intervention studies are prevalent; even though they often entail more favourable conditions than interventions in the natural settings. Thus, in the framework of an intervention study, the present study aims to explore social-ecological, motivational and volitional correlates of South African women living with HIV with regard to physical activity and participation in a sport and exercise health promotion programme. The qualitative data was produced in the framework of a non-randomised pre-post intervention study that evaluated structure, processes and outcomes of a 10-week sport and exercise programme. All 25 participants of the programme were included in this analysis, independent of compliance. Data was produced through questionnaires, participatory group discussions, body image pictures, research diaries and individual semi-structured interviews. All participants lived in a low socioeconomic, disadvantaged setting. Hence, the psychological correlates are contextualised and social-ecological influences on perception and behaviour are discussed. The results show the importance of considering social-cultural and environmental influences on individual motives, perceptions and expectancies, the fear of disclosure and stigmatisation, sport and exercise-specific group dynamics and self-supporting processes. Opportunities and strategies to augment physical activity and participation in sport and exercise programmes in the context of HIV are discussed.

A new supernova light curve modeling program

NASA Astrophysics Data System (ADS)

Jäger, Zoltán; Nagy, Andrea P.; Biro, Barna I.; Vinkó, József

2017-12-01

Supernovae are extremely energetic explosions that highlight the violent deaths of various types of stars. Studying such cosmic explosions may be important because of several reasons. Supernovae play a key role in cosmic nucleosynthesis processes, and they are also the anchors of methods of measuring extragalactic distances. Several exotic physical processes take place in the expanding ejecta produced by the explosion. We have developed a fast and simple semi-analytical code to model the the light curve of core collapse supernovae. This allows the determination of their most important basic physical parameters, like the the radius of the progenitor star, the mass of the ejected envelope, the mass of the radioactive nickel synthesized during the explosion, among others.

Cerenkov luminescence imaging: physics principles and potential applications in biomedical sciences.

PubMed

Ciarrocchi, Esther; Belcari, Nicola

2017-12-01

Cerenkov luminescence imaging (CLI) is a novel imaging modality to study charged particles with optical methods by detecting the Cerenkov luminescence produced in tissue. This paper first describes the physical processes that govern the production and transport in tissue of Cerenkov luminescence. The detectors used for CLI and their most relevant specifications to optimize the acquisition of the Cerenkov signal are then presented, and CLI is compared with the other optical imaging modalities sharing the same data acquisition and processing methods. Finally, the scientific work related to CLI and the applications for which CLI has been proposed are reviewed. The paper ends with some considerations about further perspectives for this novel imaging modality.

EPITAXIAL GROWTH OF SILICON

DTIC Science & Technology

Epitaxial growth of silicon on a silicon substrate by hydrogen reduction of SiCl4 was investigated. The chemical and physical processes involved in...silicon layers were produced at temperatures between 1100 and 1300 C. The effects of the concentration of SiCl4 in H2, the flow rate of the gas, the

Photochemical Upconversion: A Physical or Inorganic Chemistry Experiment for Undergraduates Using a Conventional Fluorimeter

ERIC Educational Resources Information Center

Wilke, Bryn M.; Castellano, Felix N.

2013-01-01

Photochemical upconversion is a regenerative process that transforms lower-energy photons into higher-energy light through two sequential bimolecular reactions, triplet sensitization of an appropriate acceptor followed by singlet fluorescence producing triplet-triplet annihilation derived from two energized acceptors. This laboratory directly…

Compendium of fluorine data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Detamore, J.A.

1983-04-16

Research was conducted to locate information about fluorine. This information includes chemical and physical properties of fluorine, physiological effects produced by the material, first-aid, personnel and facility protection, and materials of construction required when handling fluorine in piping and process vessels. The results of this research have been compiled in this report.

Rapid prototyping in orthopaedic surgery: a user's guide.

PubMed

Frame, Mark; Huntley, James S

2012-01-01

Rapid prototyping (RP) is applicable to orthopaedic problems involving three dimensions, particularly fractures, deformities, and reconstruction. In the past, RP has been hampered by cost and difficulties accessing the appropriate expertise. Here we outline the history of rapid prototyping and furthermore a process using open-source software to produce a high fidelity physical model from CT data. This greatly mitigates the expense associated with the technique, allowing surgeons to produce precise models for preoperative planning and procedure rehearsal. We describe the method with an illustrative case.

A source mechanism producing HF-induced plasma lines (HFPLS) with up-shifted frequencies

NASA Technical Reports Server (NTRS)

Kuo, S. P.; Lee, M. C.

1992-01-01

Attention is given to a nonlinear scattering process analyzed as a source mechanism producing the frequency up-shifted HFPLs observed in the Arecibo ionospheric heating experiments. A physical picture is offered to explain how Langmuir waves with frequencies greater than the HF heater wave frequency can be produced in the heating experiments and be detected by incoherent radars as frequency up-shifted HFPLs. Since the considered scattering process occurs in a region near the reflection height, it explains why the frequency up-shifted HFPLs should originate from the altitude near the reflection height as observed. The theory also shows that the amount of frequency up-shift is inversely proportional to the frequency of the HF heater and increases linearly with the electron temperature. The quantitative analysis of the theory shows a good agreement with the experimental results.

Characterizations of additive manufactured porous titanium implants.

PubMed

Basalah, Ahmad; Shanjani, Yaser; Esmaeili, Shahrzad; Toyserkani, Ehsan

2012-10-01

This article describes physical, chemical, and mechanical characterizations of porous titanium implants made by an additive manufacturing method to gain insight into the correlation of process parameters and final physical properties of implants used in orthopedics. For the manufacturing chain, the powder metallurgy technology was combined with the additive manufacturing to fabricate the porous structure from the pure tanium powder. A 3D printing machine was employed in this study to produce porous bar samples. A number of physical parameters such as titanium powder size, polyvinyl alcohol (PVA) amount, sintering temperature and time were investigated to control the mechanical properties and porosity of the structures. The produced samples were characterized through porosity and shrinkage measurements, mechanical compression test and scanning electron microscopy (SEM). The results showed a level of porosity in the samples in the range of 31-43%, which is within the range of the porosity of the cancelluous bone and approaches the range of the porosity of the cortical bone. The results of the mechanical test showed that the compressive strength is in the wide range of 56-509 MPa implying the effect of the process parameters on the mechanical strengths. This technique of manufacturing of Ti porous structures demonstrated a low level of shrinkage with the shrinkage percentage ranging from 1.5 to 5%. Copyright © 2012 Wiley Periodicals, Inc.

Quality evaluation of probiotic capsule prepared from alginate, carrageenan and tofu waste flour based on bacterial activity and organoleptic test

NASA Astrophysics Data System (ADS)

Muhardina, V.; Ermaya, D.; Aisyah, Y.; Haryani, S.

2018-02-01

Probiotic capsule is an innovation in functional food sector. It is used to preserve the living cells of probiotic bacteria during processing and storage. In this research, the improvement of probiotic viability is studied by using two kinds of encapsulating biomaterials and different concentration of tofu waste flour. Extrusion is selected method for encapsulation process. The purpose of this study is to examine the quality of probiotic capsule by evaluating the lactic acid bacteria performance and its physical characteristic. The article provides the data of probiotic bacteria activity related to their living cells present in capsule, activity in fermentation media compare to uncapsulated bacteria, and panelists’ preferences of capsule’s physical properties. The data is analyzed statistically by using ANOVA. The result shows that variables in this study affect the number of bacteria, their metabolic activity in producing acid during fermentation, and physical appearance of the capsule. Combination of alginate and tofu waste flour allows the multiplication of bacteria to a high number, and forms elastic, yellow and cloudy capsule, while with carrageenan, it causes the growth of a few numbers of bacteria which affects to a moderate pH and produces elastic, creamy and transparent capsule.

DOES A SCALING LAW EXIST BETWEEN SOLAR ENERGETIC PARTICLE EVENTS AND SOLAR FLARES?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kahler, S. W., E-mail: AFRL.RVB.PA@kirtland.af.mil

2013-05-20

Among many other natural processes, the size distributions of solar X-ray flares and solar energetic particle (SEP) events are scale-invariant power laws. The measured distributions of SEP events prove to be distinctly flatter, i.e., have smaller power-law slopes, than those of the flares. This has led to speculation that the two distributions are related through a scaling law, first suggested by Hudson, which implies a direct nonlinear physical connection between the processes producing the flares and those producing the SEP events. We present four arguments against this interpretation. First, a true scaling must relate SEP events to all flare X-raymore » events, and not to a small subset of the X-ray event population. We also show that the assumed scaling law is not mathematically valid and that although the flare X-ray and SEP event data are correlated, they are highly scattered and not necessarily related through an assumed scaling of the two phenomena. An interpretation of SEP events within the context of a recent model of fractal-diffusive self-organized criticality by Aschwanden provides a physical basis for why the SEP distributions should be flatter than those of solar flares. These arguments provide evidence against a close physical connection of flares with SEP production.« less

Graphene growth process modeling: a physical-statistical approach

NASA Astrophysics Data System (ADS)

Wu, Jian; Huang, Qiang

2014-09-01

As a zero-band semiconductor, graphene is an attractive material for a wide variety of applications such as optoelectronics. Among various techniques developed for graphene synthesis, chemical vapor deposition on copper foils shows high potential for producing few-layer and large-area graphene. Since fabrication of high-quality graphene sheets requires the understanding of growth mechanisms, and methods of characterization and control of grain size of graphene flakes, analytical modeling of graphene growth process is therefore essential for controlled fabrication. The graphene growth process starts with randomly nucleated islands that gradually develop into complex shapes, grow in size, and eventually connect together to cover the copper foil. To model this complex process, we develop a physical-statistical approach under the assumption of self-similarity during graphene growth. The growth kinetics is uncovered by separating island shapes from area growth rate. We propose to characterize the area growth velocity using a confined exponential model, which not only has clear physical explanation, but also fits the real data well. For the shape modeling, we develop a parametric shape model which can be well explained by the angular-dependent growth rate. This work can provide useful information for the control and optimization of graphene growth process on Cu foil.

Semantic modeling of plastic deformation of polycrystalline rock

NASA Astrophysics Data System (ADS)

Babaie, Hassan A.; Davarpanah, Armita

2018-02-01

We have developed the first iteration of the Plastic Rock Deformation (PRD) ontology by modeling the semantics of a selected set of deformational processes and mechanisms that produce, reconfigure, displace, and/or consume the material components of inhomogeneous polycrystalline rocks. The PRD knowledge model also classifies and formalizes the properties (relations) that hold between instances of the dynamic physical and chemical processes and the rock components, the complex physio-chemical, mathematical, and informational concepts of the plastic rock deformation system, the measured or calculated laboratory testing conditions, experimental procedures and protocols, the state and system variables, and the empirical flow laws that define the inter-relationships among the variables. The ontology reuses classes and properties from several existing ontologies that are built for physics, chemistry, biology, and mathematics. With its flexible design, the PRD ontology is well positioned to incrementally develop into a model that more fully represents the knowledge of plastic deformation of polycrystalline rocks in the future. The domain ontology will be used to consistently annotate varied data and information related to the microstructures and the physical and chemical processes that produce them at different spatial and temporal scales in the laboratory and in the solid Earth. The PRDKB knowledge base, when built based on the ontology, will help the community of experimental structural geologists and metamorphic petrologists to coherently and uniformly distribute, discover, access, share, and use their data through automated reasoning and integration and query of heterogeneous experimental deformation data that originate from autonomous rock testing laboratories.

Methane Pyrolysis and Disposing Off Resulting Carbon

NASA Technical Reports Server (NTRS)

Sharma, P. K.; Rapp, D.; Rahotgi, N. K.

1999-01-01

Sabatier/Electrolysis (S/E) is a leading process for producing methane and oxygen for application to Mars ISPP. One significant problem with this process is that it produces an excess of methane for combustion with the amount of oxygen that is produced. Therefore, one must discard roughly half of the methane to obtain the proper stoichiometric methane/oxygen mixture for ascent from Mars. This is a waste of hydrogen, which must be brought from Earth and is difficult to transport to Mars and store on Mars. To reduce the problem of transporting hydrogen to Mars, the S/E process can be augmented by another process which reduces overall hydrogen requirement. Three conceptual approaches for doing this are (i) recover hydrogen from the excess methane produced by the S/E process, (ii) convert the methane to a higher hydrocarbon or other organic with a lower H/C ratio than methane, and (iii) use a separate process (such as zirconia or reverse water gas shift reaction) to produce additional oxygen, thus utilizing all the methane produced by the Sabatier process. We report our results here on recovering hydrogen from the excess methane using pyrolysis of methane. Pyrolysis has the advantage that it produces almost pure hydrogen, and any unreacted methane can pass through the S/E process reactor. It has the disadvantage that disposing of the carbon produced by pyrolysis presents difficulties. The goals of a research program on recovery of hydrogen from methane are (in descending priority order): 1) Study the kinetics of pyrolysis to arrive at a pyrolysis reactor design that produces high yields in a confined volume at the lowest possible operating temperature; 2) Study the kinetics of carbon burnoff to determine whether high yields can be obtained in a confined volume at acceptable operating temperatures; and 3) Investigate catalytic techniques for depositing carbon as a fine soot which can be physically separated from the reactor. In the JPL program, we have made significant measurements in regard to goal 1, cursory measurements in regard to goal 2, and would plan to pursue goal 3 if additional resources are secured.

The contribution of microbunching instability to solar flare emission in the GHz to THz range of frequencies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klopf, J. Michael; Kaufmann, Pierre; Raulin, Jean-Pierre

2014-07-01

Recent solar flare observations in the sub-terahertz range have provided evidence of a new spectral component with fluxes increasing for larger frequencies, separated from the well-known microwave emission that maximizes in the gigahertz range. Suggested interpretations explain the terahertz spectral component but do not account for the simultaneous microwave component. We present a mechanism for producing the observed "double spectra." Based on coherent enhancement of synchrotron emission at long wavelengths in laboratory accelerators, we consider how similar processes may occur within a solar flare. The instability known as microbunching arises from perturbations that produce electron beam density modulations, giving risemore » to broadband coherent synchrotron emission at wavelengths comparable to the characteristic size of the microbunch structure. The spectral intensity of this coherent synchrotron radiation (CSR) can far exceed that of the incoherent synchrotron radiation (ISR), which peaks at a higher frequency, thus producing a double-peaked spectrum. Successful CSR simulations are shown to fit actual burst spectral observations, using typical flaring physical parameters and power-law energy distributions for the accelerated electrons. The simulations consider an energy threshold below which microbunching is not possible because of Coulomb repulsion. Only a small fraction of the radiating charges accelerated to energies above the threshold is required to produce the microwave component observed for several events. The ISR/CSR mechanism can occur together with other emission processes producing the microwave component. It may bring an important contribution to microwaves, at least for certain events where physical conditions for the occurrence of the ISR/CSR microbunching mechanism are possible.« less

Soil Carbon Dioxide Production and Surface Fluxes: Subsurface Physical Controls

NASA Astrophysics Data System (ADS)

Risk, D.; Kellman, L.; Beltrami, H.

Soil respiration is a critical determinant of landscape carbon balance. Variations in soil temperature and moisture patterns are important physical processes controlling soil respiration which need to be better understood. Relationships between soil respi- ration and physical controls are typically addressed using only surface flux data but other methods also exist which permit more rigorous interpretation of soil respira- tion processes. Here we use a combination of subsurface CO_{2} concentrations, surface CO_{2} fluxes and detailed physical monitoring of the subsurface envi- ronment to examine physical controls on soil CO_{2} production at four climate observatories in Eastern Canada. Results indicate that subsurface CO_{2} produc- tion is more strongly correlated to the subsurface thermal environment than the surface CO_{2} flux. Soil moisture was also found to have an important influence on sub- surface CO_{2} production, particularly in relation to the soil moisture - soil profile diffusivity relationship. Non-diffusive profile CO_{2} transport appears to be im- portant at these sites, resulting in a de-coupling of summertime surface fluxes from subsurface processes and violating assumptions that surface CO_{2} emissions are the result solely of diffusion. These results have implications for the study of soil respiration across a broad range of terrestrial environments.

Optical studies of dynamical processes in disordered materials

NASA Astrophysics Data System (ADS)

Yen, William M.

1990-12-01

The research continues to focus on the study of the structure and the dynamic behavior of insulating solids which can be activated optically. The physical processes which produce relaxation and energy transfer in the optical excited states were of particular interest. The studies were based principally on optical laser spectroscopic techniques which reveal a more detailed view of the materials of interest and which will ultimately lead to the development of more efficient optoelectronic materials.

Dense chitosan surgical membranes produced by a coincident compression-dehydration process

PubMed Central

Dooley, Thomas P.; Ellis, April L.; Belousova, Maria; Petersen, Don; DeCarlo, Arthur A.

2012-01-01

High density chitosan membranes were produced via a novel manufacturing process for use as implantable resorbable surgical membranes. The innovative method utilizes the following three sequential steps: (1) casting an acidic chitosan solution within a silicon mold, followed by freezing; (2) neutralizing the frozen acidic chitosan solution in alkaline solution to facilitate polymerization; and (3) applying coincident compression-dehydration under a vacuum. Resulting membranes of 0.2 – 0.5 mm thickness have densities as high as 1.6 g/cm3. Inclusion of glycerol prior to the compression-dehydration step provides additional physical and clinical handling benefits. The biomaterials exhibit tensile strength with a maximum load as high as 10.9 N at ~ 2.5 mm width and clinically-relevant resistance to suture pull-out with a maximum load as high as 2.2 N. These physical properties were superior to those of a commercial reconstituted collagen membrane. The dense chitosan membranes have excellent clinical handling characteristics, such as pliability and “memory” when wet. They are semi-permeable to small molecules, biodegradable in vitro in lysozyme solution, and the rates of degradation are inversely correlated to the degree of deacetylation. Furthermore, the dense chitosan membranes are biocompatible and resorbable in vivo as demonstrated in a rat oral wound healing model. The unique combination of physical, in vitro, in vivo, and clinical handling properties demonstrate the high utility of dense chitosan membranes produced by this new method. The materials may be useful as surgical barrier membranes, scaffolds for tissue engineering, wound dressings, and as delivery devices for active ingredients. PMID:23565872

Designer's approach for scene selection in tests of preference and restoration along a continuum of natural to manmade environments.

PubMed

Hunter, MaryCarol R; Askarinejad, Ali

2015-01-01

It is well-established that the experience of nature produces an array of positive benefits to mental well-being. Much less is known about the specific attributes of green space which produce these effects. In the absence of translational research that links theory with application, it is challenging to design urban green space for its greatest restorative potential. This translational research provides a method for identifying which specific physical attributes of an environmental setting are most likely to influence preference and restoration responses. Attribute identification was based on a triangulation process invoking environmental psychology and aesthetics theories, principles of design founded in mathematics and aesthetics, and empirical research on the role of specific physical attributes of the environment in preference or restoration responses. From this integration emerged a list of physical attributes defining aspects of spatial structure and environmental content found to be most relevant to the perceptions involved with preference and restoration. The physical attribute list offers a starting point for deciphering which scene stimuli dominate or collaborate in preference and restoration responses. To support this, functional definitions and metrics-efficient methods for attribute quantification are presented. Use of these research products and the process for defining place-based metrics can provide (a) greater control in the selection and interpretation of the scenes/images used in tests of preference and restoration and (b) an expanded evidence base for well-being designers of the built environment.

Designer's approach for scene selection in tests of preference and restoration along a continuum of natural to manmade environments

PubMed Central

Hunter, MaryCarol R.; Askarinejad, Ali

2015-01-01

It is well-established that the experience of nature produces an array of positive benefits to mental well-being. Much less is known about the specific attributes of green space which produce these effects. In the absence of translational research that links theory with application, it is challenging to design urban green space for its greatest restorative potential. This translational research provides a method for identifying which specific physical attributes of an environmental setting are most likely to influence preference and restoration responses. Attribute identification was based on a triangulation process invoking environmental psychology and aesthetics theories, principles of design founded in mathematics and aesthetics, and empirical research on the role of specific physical attributes of the environment in preference or restoration responses. From this integration emerged a list of physical attributes defining aspects of spatial structure and environmental content found to be most relevant to the perceptions involved with preference and restoration. The physical attribute list offers a starting point for deciphering which scene stimuli dominate or collaborate in preference and restoration responses. To support this, functional definitions and metrics—efficient methods for attribute quantification are presented. Use of these research products and the process for defining place-based metrics can provide (a) greater control in the selection and interpretation of the scenes/images used in tests of preference and restoration and (b) an expanded evidence base for well-being designers of the built environment. PMID:26347691

Control and monitoring method and system for electromagnetic forming process

DOEpatents

Kunerth, Dennis C.; Lassahn, Gordon D.

1990-01-01

A process, system, and improvement for a process for electromagnetic forming of a workpiece in which characteristics of the workpiece such as its geometry, electrical conductivity, quality, and magnetic permeability can be determined by monitoring the current and voltage in the workcoil. In an electromagnet forming process in which a power supply provides current to a workcoil and the electromagnetic field produced by the workcoil acts to form the workpiece, the dynamic interaction of the electromagnetic fields produced by the workcoil with the geometry, electrical conductivity, and magnetic permeability of the workpiece, provides information pertinent to the physical condition of the workpiece that is available for determination of quality and process control. This information can be obtained by deriving in real time the first several time derivatives of the current and voltage in the workcoil. In addition, the process can be extended by injecting test signals into the workcoil during the electromagnetic forming and monitoring the response to the test signals in the workcoil.

Long-term persistence of solar activity

NASA Technical Reports Server (NTRS)

Ruzmaikin, Alexander; Feynman, Joan; Robinson, Paul

1994-01-01

We examine the question of whether or not the non-periodic variations in solar activity are caused by a white-noise, random process. The Hurst exponent, which characterizes the persistence of a time series, is evaluated for the series of C-14 data for the time interval from about 6000 BC to 1950 AD. We find a constant Hurst exponent, suggesting that solar activity in the frequency range from 100 to 3000 years includes an important continuum component in addition to the well-known periodic variations. The value we calculate, H approximately 0.8, is significantly larger than the value of 0.5 that would correspond to variations produced by a white-noise process. This value is in good agreement with the results for the monthly sunspot data reported elsewhere, indicating that the physics that produces the continuum is a correlated random process and that it is the same type of process over a wide range of time interval lengths.

Radiation-tolerant imaging device

DOEpatents

Colella, N.J.; Kimbrough, J.R.

1996-11-19

A barrier at a uniform depth for an entire wafer is used to produce imaging devices less susceptible to noise pulses produced by the passage of ionizing radiation. The barrier prevents charge created in the bulk silicon of a CCD detector or a semiconductor logic or memory device from entering the collection volume of each pixel in the imaging device. The charge barrier is a physical barrier, a potential barrier, or a combination of both. The physical barrier is formed by an SiO{sub 2} insulator. The potential barrier is formed by increasing the concentration of majority carriers (holes) to combine with the electron`s generated by the ionizing radiation. A manufacturer of CCD imaging devices can produce radiation-tolerant devices by merely changing the wafer type fed into his process stream from a standard wafer to one possessing a barrier beneath its surface, thus introducing a very small added cost to his production cost. An effective barrier type is an SiO{sub 2} layer. 7 figs.

Technologies and Methods Used at the Laboratory for Atmospheric and Space Physics (LASP) to Serve Solar Irradiance Data

NASA Technical Reports Server (NTRS)

Pankratz, Chris; Beland, Stephane; Craft, James; Baltzer, Thomas; Wilson, Anne; Lindholm, Doug; Snow, Martin; Woods, Thomas; Woodraska, Don

2018-01-01

The Laboratory for Atmospheric and Space Physics (LASP) at the University of Colorado in Boulder, USA operates the Solar Radiation and Climate Experiment (SORCE) NASA mission, as well as several other NASA spacecraft and instruments. Dozens of Solar Irradiance data sets are produced, managed, and disseminated to the science community. Data are made freely available to the scientific immediately after they are produced using a variety of data access interfaces, including the LASP Interactive Solar Irradiance Datacenter (LISIRD), which provides centralized access to a variety of solar irradiance data sets using both interactive and scriptable/programmatic methods. This poster highlights the key technological elements used for the NASA SORCE mission ground system to produce, manage, and disseminate data to the scientific community and facilitate long-term data stewardship. The poster presentation will convey designs, technological elements, practices and procedures, and software management processes used for SORCE and their relationship to data quality and data management standards, interoperability, NASA data policy, and community expectations.

Microstructural, mechanical and oxidation features of NiCoCrAlY coating produced by plasma activated EB-PVD

NASA Astrophysics Data System (ADS)

He, Jian; Guo, Hongbo; Peng, Hui; Gong, Shengkai

2013-06-01

NiCoCrAlY coatings produced by electron beam-physical vapor deposition (EB-PVD) have been extensively used as the oxidation resistance coatings or suitable bond coats in thermal barrier coating (TBC) system. However, the inherent imperfections caused by EB-PVD process degrade the oxidation resistance of the coatings. In the present work, NiCoCrAlY coatings were creatively produced by plasma activated electron beam-physical vapor deposition (PA EB-PVD). The novel coatings showed a terraced substructure on the surface of each grain due to the increased energy of metal ions and enhanced mobility of adatoms. Also a strong (1 1 1) crystallographic texture of γ/γ' grains was observed. The toughness of the coatings got remarkably improved compared with the coatings deposited by conventional EB-PVD and the oxidation behavior at 1373 K showed that the novel coatings had excellent oxidation resistance. The possible mechanism was finally discussed.

Radiation-tolerant imaging device

DOEpatents

Colella, Nicholas J.; Kimbrough, Joseph R.

1996-01-01

A barrier at a uniform depth for an entire wafer is used to produce imaging devices less susceptible to noise pulses produced by the passage of ionizing radiation. The barrier prevents charge created in the bulk silicon of a CCD detector or a semiconductor logic or memory device from entering the collection volume of each pixel in the imaging device. The charge barrier is a physical barrier, a potential barrier, or a combination of both. The physical barrier is formed by an SiO.sub.2 insulator. The potential barrier is formed by increasing the concentration of majority carriers (holes) to combine with the electron's generated by the ionizing radiation. A manufacturer of CCD imaging devices can produce radiation-tolerant devices by merely changing the wafer type fed into his process stream from a standard wafer to one possessing a barrier beneath its surface, thus introducing a very small added cost to his production cost. An effective barrier type is an SiO.sub.2 layer.

A Modeling Framework for Predicting the Size of Sediments Produced on Hillslopes and Supplied to Channels

NASA Astrophysics Data System (ADS)

Sklar, L. S.; Mahmoudi, M.

2016-12-01

Landscape evolution models rarely represent sediment size explicitly, despite the importance of sediment size in regulating rates of bedload sediment transport, river incision into bedrock, and many other processes in channels and on hillslopes. A key limitation has been the lack of a general model for predicting the size of sediments produced on hillslopes and supplied to channels. Here we present a framework for such a model, as a first step toward building a `geomorphic transport law' that balances mechanistic realism with computational simplicity and is widely applicable across diverse landscapes. The goal is to take as inputs landscape-scale boundary conditions such as lithology, climate and tectonics, and predict the spatial variation in the size distribution of sediments supplied to channels across catchments. The model framework has two components. The first predicts the initial size distribution of particles produced by erosion of bedrock underlying hillslopes, while the second accounts for the effects of physical and chemical weathering during transport down slopes and delivery to channels. The initial size distribution can be related to the spacing and orientation of fractures within bedrock, which depend on the stresses and deformation experienced during exhumation and on rock resistance to fracture propagation. Other controls on initial size include the sizes of mineral grains in crystalline rocks, the sizes of cemented particles in clastic sedimentary rocks, and the potential for characteristic size distributions produced by tree throw, frost cracking, and other erosional processes. To model how weathering processes transform the initial size distribution we consider the effects of erosion rate and the thickness of soil and weathered bedrock on hillslope residence time. Residence time determines the extent of size reduction, for given values of model terms that represent the potential for chemical and physical weathering. Chemical weathering potential is parameterized in terms of mean annual precipitation and temperature, and the fraction of soluble minerals. Physical weathering potential can be parameterized in terms of topographic attributes, including slope, curvature and aspect. Finally, we compare model predictions with field data from Inyo Creek in the Sierra Nevada Mtns, USA.

Remote Sensing Image Quality Assessment Experiment with Post-Processing

NASA Astrophysics Data System (ADS)

Jiang, W.; Chen, S.; Wang, X.; Huang, Q.; Shi, H.; Man, Y.

2018-04-01

This paper briefly describes the post-processing influence assessment experiment, the experiment includes three steps: the physical simulation, image processing, and image quality assessment. The physical simulation models sampled imaging system in laboratory, the imaging system parameters are tested, the digital image serving as image processing input are produced by this imaging system with the same imaging system parameters. The gathered optical sampled images with the tested imaging parameters are processed by 3 digital image processes, including calibration pre-processing, lossy compression with different compression ratio and image post-processing with different core. Image quality assessment method used is just noticeable difference (JND) subject assessment based on ISO20462, through subject assessment of the gathered and processing images, the influence of different imaging parameters and post-processing to image quality can be found. The six JND subject assessment experimental data can be validated each other. Main conclusions include: image post-processing can improve image quality; image post-processing can improve image quality even with lossy compression, image quality with higher compression ratio improves less than lower ratio; with our image post-processing method, image quality is better, when camera MTF being within a small range.

Neural Bases of Social Anxiety Disorder: Emotional Reactivity and Cognitive Regulation During Social and Physical Threat

PubMed Central

Goldin, Philippe R.; Manber, Tali; Hakimi, Shabnam; Canli, Turhan; Gross, James J.

2014-01-01

Context Social anxiety disorder is thought to involve emotional hyper-reactivity, cognitive distortions, and ineffective emotion regulation. While the neural bases of emotional reactivity to social stimuli have been described, the neural bases of emotional reactivity and cognitive regulation during social and physical threat, and their relationship to social anxiety symptom severity, have yet to be investigated. Objective This study investigated behavioral and neural correlates of emotional reactivity and cognitive regulation in patients and controls during processing of social and physical threat stimuli. Design Participants were trained to implement cognitive-linguistic regulation of emotional reactivity induced by social (harsh facial expressions) and physical (violent scenes) threat while undergoing functional magnetic resonance imaging and providing behavioral ratings of negative emotion experience. Setting Academic psychology department. Participants 15 adults with social anxiety disorder and 17 demographically-matched healthy controls. Main Outcome Measures Blood oxygen level dependent signal and negative emotion ratings. Results Behaviorally, patients reported greater negative emotion than controls during social and physical threat, but showed equivalent reduction in negative emotion following cognitive regulation. Neurally, viewing social threat resulted in greater emotion-related neural responses in patients than controls, with social anxiety symptom severity related to activity in a network of emotion and attention processing regions in patients only. Viewing physical threat produced no between-group differences. Regulation during social threat resulted in greater cognitive and attention regulation-related brain activation in controls compared to patients. Regulation during physical threat produced greater cognitive control-related response (i.e., right DLPFC) in patients compared to controls. Conclusions Compared to controls, patients demonstrated exaggerated negative emotion reactivity and reduced cognitive regulation related neural activation, specifically for social threat stimuli. These findings help to elucidate potential neural mechanisms of emotion regulation that might serve as biomarkers for interventions for social anxiety disorder. PMID:19188539

NREL Solar Researcher Honored with ASES Abbot Award | News | NREL

Science.gov Websites

desiccant cooling test laboratory, producing NREL's solar industrial process heat design handbook , developing stretched-membrane parabolic dish solar concentrators, inventing a high-performance heat exchanger the sun's heat to warm the building ventilation air. Kutscher has a B.S. degree in physics from the

Optical disk processing of solar images.

NASA Astrophysics Data System (ADS)

Title, A.; Tarbell, T.

The current generation of space and ground-based experiments in solar physics produces many megabyte-sized image data arrays. Optical disk technology is the leading candidate for convenient analysis, distribution, and archiving of these data. The authors have been developing data analysis procedures which use both analog and digital optical disks for the study of solar phenomena.

A recipe for primordial soup

NASA Technical Reports Server (NTRS)

Kolb, E.

2001-01-01

If the universe emerged from a state of high temperature and high density, we can study the origin of the universe by recreating those conditions in the laboratory. While we can not reproduce the Big Bang, we can recreate its conditions and study the physical processes responsible for producing the rich and varied universe we observe today.

Characterization of designer biochar produced at different temperatures and their effects on a loamy sand

USDA-ARS?s Scientific Manuscript database

Biochar supplements to degraded soils have the potential to improve crop yield and soil quality. We hypothesize that the biochar chemical production process can be tailored to form designer biochars that have specific chemical characteristics matched to selective chemical and/or physical issues of a...

Uranium to Electricity: The Chemistry of the Nuclear Fuel Cycle

ERIC Educational Resources Information Center

Settle, Frank A.

2009-01-01

The nuclear fuel cycle consists of a series of industrial processes that produce fuel for the production of electricity in nuclear reactors, use the fuel to generate electricity, and subsequently manage the spent reactor fuel. While the physics and engineering of controlled fission are central to the generation of nuclear power, chemistry…

An operational mesoscale ensemble data assimilation and prediction system: E-RTFDDA

NASA Astrophysics Data System (ADS)

Liu, Y.; Hopson, T.; Roux, G.; Hacker, J.; Xu, M.; Warner, T.; Swerdlin, S.

2009-04-01

Mesoscale (2-2000 km) meteorological processes differ from synoptic circulations in that mesoscale weather changes rapidly in space and time, and physics processes that are parameterized in NWP models play a great role. Complex interactions of synoptic circulations, regional and local terrain, land-surface heterogeneity, and associated physical properties, and the physical processes of radiative transfer, cloud and precipitation and boundary layer mixing, are crucial in shaping regional weather and climate. Mesoscale ensemble analysis and prediction should sample the uncertainties of mesoscale modeling systems in representing these factors. An innovative mesoscale Ensemble Real-Time Four Dimensional Data Assimilation (E-RTFDDA) and forecasting system has been developed at NCAR. E-RTFDDA contains diverse ensemble perturbation approaches that consider uncertainties in all major system components to produce multi-scale continuously-cycling probabilistic data assimilation and forecasting. A 30-member E-RTFDDA system with three nested domains with grid sizes of 30, 10 and 3.33 km has been running on a Department of Defense high-performance computing platform since September 2007. It has been applied at two very different US geographical locations; one in the western inter-mountain area and the other in the northeastern states, producing 6 hour analyses and 48 hour forecasts, with 4 forecast cycles a day. The operational model outputs are analyzed to a) assess overall ensemble performance and properties, b) study terrain effect on mesoscale predictability, c) quantify the contribution of different ensemble perturbation approaches to the overall forecast skill, and d) assess the additional contributed skill from an ensemble calibration process based on a quantile-regression algorithm. The system and the results will be reported at the meeting.

Critical considerations for the qualitative and quantitative determination of process-induced disorder in crystalline solids.

PubMed

Newman, Ann; Zografi, George

2014-09-01

Solid-state instabilities in crystalline solids arise during processing primarily because a certain level of structural disorder has been introduced into the crystal. Many physical instabilities appear to be associated with the recrystallization of molecules from these disordered regions, while chemical instabilities arise from sufficient molecular mobility to allow solid-state chemical reactivity. In this Commentary we discuss the various forms of structural disorder, processing which can produce disorder, the quantitative analysis of process-induced order, and strategies to limit disorder and its effects. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

Reviews

NASA Astrophysics Data System (ADS)

2006-11-01

WE RECOMMEND Critical mass Philip Ball explores the idea of the physics of society. Eurekas and Euphorias A humorous yet insightful collection of scientific anecdotes. Wind turbine Low-cost wind turbine produces excellent results. Science Center Nemo Hands-on science centre has some great displays for teenagers. Crocodile Physics There’s something for everyone in this lesson software package. Wireless Dynamics Sensor System A fun way to measure and record altitude and acceleration. WORTH A LOOK Climate Change Begins at Home This well researched book tackles the issue of saving our planet. The Little Doctor Datalogger Datalogger has lots of facilities but needs some manual processing. HANDLE WITH CARE The Physics of Basketball Only of interest to budding physicists obsessed with basketball. Virtual Physics This package offers nice simulations but not a lot else. WEB WATCH An eclectic mix of nuclear- and general-physics websites.

Ionospheric chemical releases

NASA Technical Reports Server (NTRS)

Bernhardt, Paul A.; Scales, W. A.

1990-01-01

Ionospheric plasma density irregularities can be produced by chemical releases into the upper atmosphere. F-region plasma modification occurs by: (1) chemically enhancing the electron number density; (2) chemically reducing the electron population; or (3) physically convecting the plasma from one region to another. The three processes (production, loss, and transport) determine the effectiveness of ionospheric chemical releases in subtle and surprising ways. Initially, a chemical release produces a localized change in plasma density. Subsequent processes, however, can lead to enhanced transport in chemically modified regions. Ionospheric modifications by chemical releases excites artificial enhancements in airglow intensities by exothermic chemical reactions between the newly created plasma species. Numerical models were developed to describe the creation and evolution of large scale density irregularities and airglow clouds generated by artificial means. Experimental data compares favorably with theses models. It was found that chemical releases produce transient, large amplitude perturbations in electron density which can evolve into fine scale irregularities via nonlinear transport properties.

A Multi-Scale, Multi-Physics Optimization Framework for Additively Manufactured Structural Components

NASA Astrophysics Data System (ADS)

El-Wardany, Tahany; Lynch, Mathew; Gu, Wenjiong; Hsu, Arthur; Klecka, Michael; Nardi, Aaron; Viens, Daniel

This paper proposes an optimization framework enabling the integration of multi-scale / multi-physics simulation codes to perform structural optimization design for additively manufactured components. Cold spray was selected as the additive manufacturing (AM) process and its constraints were identified and included in the optimization scheme. The developed framework first utilizes topology optimization to maximize stiffness for conceptual design. The subsequent step applies shape optimization to refine the design for stress-life fatigue. The component weight was reduced by 20% while stresses were reduced by 75% and the rigidity was improved by 37%. The framework and analysis codes were implemented using Altair software as well as an in-house loading code. The optimized design was subsequently produced by the cold spray process.

Complete Systematic Error Model of SSR for Sensor Registration in ATC Surveillance Networks

PubMed Central

Besada, Juan A.

2017-01-01

In this paper, a complete and rigorous mathematical model for secondary surveillance radar systematic errors (biases) is developed. The model takes into account the physical effects systematically affecting the measurement processes. The azimuth biases are calculated from the physical error of the antenna calibration and the errors of the angle determination dispositive. Distance bias is calculated from the delay of the signal produced by the refractivity index of the atmosphere, and from clock errors, while the altitude bias is calculated taking into account the atmosphere conditions (pressure and temperature). It will be shown, using simulated and real data, that adapting a classical bias estimation process to use the complete parametrized model results in improved accuracy in the bias estimation. PMID:28934157

Physical metallurgy of BATMAN II Ti-bearing martensitic steels

NASA Astrophysics Data System (ADS)

Pilloni, L.; Attura, F.; Calza-Bini, A.; De Santis, G.; Filacchioni, G.; Carosi, A.; Amato, S.

1998-10-01

Seven laboratory experimental casts of 7-9% Cr Ti-bearing martensitic steels were obtained via VIM process. Plates of 25 mm thickness were produced by hot rolling. On each cast CCT diagrams and critical temperatures were determined. Several austenitizing treatments were performed to study the grain size evolution. The effect of microstructure on impact properties were finally investigated. This paper discusses the role of chemical composition on microstructural and physical properties and shows the beneficial effect either of low-temperature austenitizing or double-austenitizing steps on impact properties.

Generative Representations for the Automated Design of Modular Physical Robots

NASA Technical Reports Server (NTRS)

Hornby, Gregory S.; Lipson, Hod; Pollack, Jordan B.

2003-01-01

We will begin with a brief background of evolutionary robotics and related work, and demonstrate the scaling problem with our own prior results. Next we propose the use of an evolved generative representation as opposed to a non-generative representation. We describe this representation in detail as well as the evolutionary process that uses it. We then compare progress of evolved robots with and without the use of the grammar, and quantify the obtained advantage. Working two- dimensional and three-dimensional physical robots produced by the system are shown.

X-ray emission from high temperature plasmas

NASA Technical Reports Server (NTRS)

Harries, W. L.

1976-01-01

The physical processes occurring in plasma focus devices were studied. These devices produce dense high temperature plasmas, which emit X rays of hundreds of KeV energy and one to ten billion neutrons per pulse. The processes in the devices seem related to solar flare phenomena, and would also be of interest for controlled thermonuclear fusion applications. The high intensity, short duration bursts of X rays and neutrons could also possibly be used for pumping nuclear lasers.

A Brief History of Physics in China,

DTIC Science & Technology

1982-07-29

not attracted by magnets. Chang Hua noticed that a static charge was produced in combing hair and in undressing with silk and wool garments. He...after the expiration of the greenish white gas. It is at this moment that casting can be performed’. For the process of smelting and casting, since there...orange, then yellow, and appears white at about 1000°C. In the process of heating pottery and metals, the ancient Chinese mastered the knowledge of

Catalysts and methods for converting carbonaceous materials to fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hensley, Jesse; Ruddy, Daniel A.; Schaidle, Joshua A.

Catalysts and processes designed to convert DME and/or methanol and hydrogen (H.sub.2) to desirable liquid fuels are described. These catalysts produce the fuels efficiently and with a high selectivity and yield, and reduce the formation of aromatic hydrocarbons by incorporating H.sub.2 into the products. Also described are process methods to further upgrade these fuels to higher molecular weight liquid fuel mixtures, which have physical properties comparable with current commercially used liquid fuels.

Environmental, Economic, and Scalability Considerations and Trends of Selected Fuel Economy-Enhancing Biomass-Derived Blendstocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dunn, Jennifer B.; Biddy, Mary; Jones, Susanne

24 biomass-derived compounds and mixtures, identified based on their physical properties, that could be blended into fuels to improve spark ignition engine fuel economy were assessed for their economic, technology readiness, and environmental viability. These bio-blendstocks were modeled to be produced biochemically, thermochemically, or through hybrid processes. To carry out the assessment, 17 metrics were developed for which each bio-blendstock was determined to be favorable, neutral, or unfavorable. Cellulosic ethanol was included as a reference case. Overall, bio-blendstock yields in biochemical processes were lower than in thermochemical processes, in which all biomass, including lignin, is converted to a product. Bio-blendstockmore » yields were a key determinant in overall viability. Key knowledge gaps included the degree of purity needed for use as a bio-blendstock as compared to a chemical. Less stringent purification requirements for fuels could cut processing costs and environmental impacts. Additionally, more information is needed on the blendability of many of these bio-blendstocks with gasoline to support the technology readiness evaluation. Overall, the technology to produce many of these blendstocks from biomass is emerging and as it matures, these assessments must be revisited. Importantly, considering economic, environmental, and technology readiness factors in addition to physical properties of blendstocks that could be used to boost fuel economy can help spotlight those most likely to be viable in the near term.« less

The physics of lightning

NASA Astrophysics Data System (ADS)

Dwyer, Joseph R.; Uman, Martin A.

2014-01-01

Despite being one of the most familiar and widely recognized natural phenomena, lightning remains relatively poorly understood. Even the most basic questions of how lightning is initiated inside thunderclouds and how it then propagates for many tens of kilometers have only begun to be addressed. In the past, progress was hampered by the unpredictable and transient nature of lightning and the difficulties in making direct measurements inside thunderstorms, but advances in instrumentation, remote sensing methods, and rocket-triggered lightning experiments are now providing new insights into the physics of lightning. Furthermore, the recent discoveries of intense bursts of X-rays and gamma-rays associated with thunderstorms and lightning illustrate that new and interesting physics is still being discovered in our atmosphere. The study of lightning and related phenomena involves the synthesis of many branches of physics, from atmospheric physics to plasma physics to quantum electrodynamics, and provides a plethora of challenging unsolved problems. In this review, we provide an introduction to the physics of lightning with the goal of providing interested researchers a useful resource for starting work in this fascinating field. By what physical mechanism or mechanisms is lightning initiated in the thundercloud? What is the maximum cloud electric field magnitude and over what volume of the cloud? What, if any, high energy processes (runaway electrons, X-rays, gamma rays) are involved in lightning initiation and how? What is the role of various forms of ice and water in lightning initiation? What physical mechanisms govern the propagation of the different types of lightning leaders (negative stepped, first positive, negative dart, negative dart-stepped, negative dart-chaotic) between cloud and ground and the leaders inside the cloud? What is the physical mechanism of leader attachment to elevated objects on the ground and to the flat ground? What are the characteristics of upward connecting leaders from those objects or from the ground? What is the physics of compact intra-cloud discharges (CIDs) (that produce a narrow bipolar wideband electric field pulse, a narrow bipolar event or NBE, apparently multiple-reflecting propagating waves within 1 km height, and copious HF and VHF radiation)? How are CIDs related to other types of preliminary breakdown pulses? Are CIDs related to the Terrestrial Gamma-Ray Flashes (TGFs) observed on orbiting satellites or to the Transient Luminous Events (TLEs) photographed above cloud tops, particularly to so-called “gigantic jets”? By what physical mechanisms do lightning leaders emit pulses of X-rays? Do the X-rays play a role in lightning propagation? By what mechanism do thunderclouds generate relatively-steady internal X-rays? Do X-rays and other high energy radiation affect cloud electrification and play a role in lightning initiation? By what physical mechanisms are Terrestrial Gamma-Ray Flashes (TGFs) produced? Do TGFs pose a hazard to individuals in aircraft? How do cloud-to-ground and intra-cloud lightning affect the upper atmosphere and ionosphere? What are the physics of the Transient Luminous Events (TLEs), “Sprites”, “jets”, and “elves”? What is the energy input into the ionosphere/magnetosphere from lightning? How exactly does rocket-and-wire (“classical” with a grounded wire and “altitude” with a floating wire) triggering of lightning work? Are there other possible and practical triggering techniques such as laser triggering? Can triggering reduce or eliminate the local occurrence of natural lightning? What are the power and energy of the component processes of lightning flashes and how are they distributed among electromagnetic processes (DC to light), thermal processes, mechanical (acoustic) processes, and relativistic (high energy) processes (runaway electrons, runaway positrons, X-ray, and gamma rays)? What is the physics of ball lightning? Is there more than one type of ball lightning? Questions 1, 2, 4, 5, 6, and 7 will be addressed directly in the following sections of this paper: Section 3. The Lightning Initiation Problem; Section 4. Lightning Propagation; Section 5. High-Energy Atmospheric Physics; Section 6. CIDs; and Section 7. TLEs.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bala, Greg Alan; Bruhn, Debby Fox; Fox, Sandra Lynn

Utilization of surfactants for improved oil recovery (IOR) is an accepted technique with high potential. However, technology application is frequently limited by cost. Biosurfactants (surface-active molecules produced by microorganisms) are not widely utilized in the petroleum industry due to high production costs associated with use of expensive substrates and inefficient product recovery methods. The economics of biosurfactant production could be significantly impacted through use of media optimization and application of inexpensive carbon substrates such as agricultural process residuals. Utilization of biosurfactants produced from agricultural residuals may 1) result in an economic advantage for surfactant production and technology application, and 2)more » convert a substantial agricultural waste stream to a value-added product for IOR. A biosurfactant with high potential for use is surfactin, a lipopeptide biosurfactant, produced by Bacillus subtilis. Reported here is the production and potential IOR utilization of surfactin produced by Bacillus subtilis (American Type Culture Collection (ATCC) 21332) from starch-based media. Production of surfactants from microbiological growth media based on simple sugars, chemically pure starch medium, simulated liquid and solid potato-process effluent media, a commercially prepared potato starch in mineral salts, and process effluent from a potato processor is discussed. Additionally, the effect of chemical and physical pretreatments on starchy feedstocks is discussed.« less

Analysis of Sulfidation Routes for Processing Weathered Ilmenite Concentrates Containing Impurities

NASA Astrophysics Data System (ADS)

Ahmad, Sazzad; Rhamdhani, M. Akbar; Pownceby, Mark I.; Bruckard, Warren J.

Rutile is the preferred feedstock for producing high-grade TiO2 pigment but due to decreasing resources, alternative materials such as ilmenite is now used to produce a synthetic rutile (SR) feedstock. This requires removal of impurities (e.g. Fe, Mg, Mn) which, for a primary ilmenite is straightforward process. Processing of weathered ilmenite however, is complex, especially when chrome-bearing impurities are present since minor chromium downgrades the SR market value as it imparts color to the final TiO2 pigment, Chrome-bearing spinels are a problem in weathered ilmenites from the Murray Basin, Australia as their physical and chemical properties overlap with ilmenite making separation difficult. In this paper, different sulfidation process routes for weathered ilmenites are analyzed for their applicability to Murray Basin deposits as a mean of remove chrome spinel impurities. Thermodynamic and experimental studies indicated that selective sulfidation of chrome-bearing spinel can be achieved under controlled pO2 and pS2 processing conditions thereby making them amenable to separation.

Recent advances in the biomimicry of structural colours.

PubMed

Dumanli, Ahu Gümrah; Savin, Thierry

2016-12-21

Nature has mastered the construction of nanostructures with well-defined macroscopic effects and purposes. Structural colouration is a visible consequence of the particular patterning of a reflecting surface with regular structures at submicron length scales. Structural colours usually appear bright, shiny, iridescent or with a metallic look, as a result of physical processes such as diffraction, interference, or scattering with a typically small dissipative loss. These features have recently attracted much research effort in materials science, chemistry, engineering and physics, in order to understand and produce structural colours. In these early stages of photonics, researchers facing an infinite array of possible colour-producing structures are heavily inspired by the elaborate architectures they find in nature. We review here the recent technological strategies employed to artificially mimic the structural colours found in nature, as well as some of their current and potential applications.

Effects of amendment of different biochars on soil physical and biological properties related to carbon mineralization

NASA Astrophysics Data System (ADS)

Zhang, Renduo; Zhu, Shuzhi; Ouyang, Lei

2014-05-01

Biochar addition to soils potentially affects various soil properties, and these effects are dependent on biochars derived from different feedstock materials and pyrolysis processes. The objective of this study was to investigate the effects of amendment of different biochars on soil physical and biological properties. Biochars were produced with dairy manure and woodchip at temperatures of 300, 500, and 700°C, respectively. Each biochar was mixed at 5% (w/w) with a forest soil and the mixture was incubated for 180 days, during which soil physical and biological properties, and soil respiration rates were measured. Results showed that the biochar addition significantly enhanced the formation of soil macroaggregates at the early incubation time. The biochar application significantly reduced soil bulk density, increased the amount of soil organic matter, and stimulated microbial activity and soil respiration rates at the early incubation stage. Biochar applications improved water retention capacity, with stronger effects by biochars produced at higher pyrolysis temperatures. At the same suction, the soil with woodchip biochars possessed higher water content than with the dairy manure biochars. Biochar addition significantly affected the soil physical and biological properties, which resulted in different soil carbon mineralization rates.

A new physical unclonable function architecture

NASA Astrophysics Data System (ADS)

Chuang, Bai; Xuecheng, Zou; Kui, Dai

2015-03-01

This paper describes a new silicon physical unclonable function (PUF) architecture that can be fabricated on a standard CMOS process. Our proposed architecture is built using process sensors, difference amplifier, comparator, voting mechanism and diffusion algorithm circuit. Multiple identical process sensors are fabricated on the same chip. Due to manufacturing process variations, each sensor produces slightly different physical characteristic values that can be compared in order to create a digital identification for the chip. The diffusion algorithm circuit ensures further that the PUF based on the proposed architecture is able to effectively identify a population of ICs. We also improve the stability of PUF design with respect to temporary environmental variations like temperature and supply voltage with the introduction of difference amplifier and voting mechanism. The PUF built on the proposed architecture is fabricated in 0.18 μm CMOS technology. Experimental results show that the PUF has a good output statistical characteristic of uniform distribution and a high stability of 98.1% with respect to temperature variation from -40 to 100 °C, and supply voltage variation from 1.7 to 1.9 V. Project supported by the National Natural Science Foundation of China (No. 61376031).

The evaluation of the microbial safety of fresh ready-to-eat vegetables produced by different technologies in Italy.

PubMed

De Giusti, M; Aurigemma, C; Marinelli, L; Tufi, D; De Medici, D; Di Pasquale, S; De Vito, C; Boccia, A

2010-09-01

The study was performed to evaluate the safety of whole and RTE vegetables and to investigate the effectiveness of different preventive strategies for the quality assurance of RTE vegetables collected from three Italian production systems. Producer 1, applied a strict system in compliance with GAP- GMP - HACCP, Producer 2 used chlorine disinfection at a second washing step, and Producer 3 using a physical microbial stabilization. During the period 2005-2007, a total of 964 samples including whole vegetables and RTE salads, collected from three different producers in central Italy, were analysed to quantify the aerobic mesophilic count (AMC) and Escherichia coli, and for the presence of Salmonella spp, Listeria monocytogenes, E. coli O157:H7, hepatitis A virus and Norovirus (NoV). None of the whole vegetable samples were positive for L. monocytogenes, E. coli O157:H7, HAV and NoV; however, a low prevalence of Salmonella was found. No pathogens were detected with cultural methods in any of the RTE vegetables analysed, only two RTE samples were positive for L. monocytogenes with PCR, but were not confirmed by the cultural method. The median values of AMC in RTE vegetables measured 24 h after packaging were statistically different among the 3 producers (5·4 × 10(6), 1·5 × 10(7) and 3·7 × 10(7) CFU g(-1), respectively; P=0·011). The lowest level was detected in Producer 1. The products that were processed applying rigorously GAP, GMP and HACCP showed a better microbiological quality than those processed with chemical or physical stabilization. STUDY SIGNIFICANCE AND IMPACT: The results of the study evidenced the efficacy of GAP, GMP and HACCP in improving microbiological quality of whole and RTE vegetables. © 2010 The Authors. Journal compilation © 2010 The Society for Applied Microbiology.

The origins of tropical marine biodiversity.

PubMed

Bowen, Brian W; Rocha, Luiz A; Toonen, Robert J; Karl, Stephen A

2013-06-01

Recent phylogeographic studies have overturned three paradigms for the origins of marine biodiversity. (i) Physical (allopatric) isolation is not the sole avenue for marine speciation: many species diverge along ecological boundaries. (ii) Peripheral habitats such as oceanic archipelagos are not evolutionary graveyards: these regions can export biodiversity. (iii) Speciation in marine and terrestrial ecosystems follow similar processes but are not the same: opportunities for allopatric isolation are fewer in the oceans, leaving greater opportunity for speciation along ecological boundaries. Biodiversity hotspots such as the Caribbean Sea and the Indo-Pacific Coral Triangle produce and export species, but can also accumulate biodiversity produced in peripheral habitats. Both hotspots and peripheral ecosystems benefit from this exchange in a process dubbed biodiversity feedback. Copyright © 2013 Elsevier Ltd. All rights reserved.

A novel bread making process using salt-stressed Baker's yeast.

PubMed

Yeh, Lien-Te; Charles, Albert Linton; Ho, Chi-Tang; Huang, Tzou-Chi

2009-01-01

By adjusting the mixing order of ingredients in traditional formula, an innovative bread making process was developed. The effect of salt-stressed Baker's yeast on bread dough of different sugar levels was investigated. Baker's yeast was stressed in 7% salt solution then mixed into dough, which was then evaluated for fermentation time, dough fermentation producing gas, dough expansion, bread specific volumes, and sensory and physical properties. The results of this study indicated that salt-stressed Baker's yeast shortened fermentation time in 16% and 24% sugar dough. Forty minutes of salt stress produced significant amount of gas and increased bread specific volumes. The bread was softer and significantly improved sensory properties for aroma, taste, and overall acceptability were obtained.

Rapid Prototyping in Orthopaedic Surgery: A User's Guide

PubMed Central

Frame, Mark; Huntley, James S.

2012-01-01

Rapid prototyping (RP) is applicable to orthopaedic problems involving three dimensions, particularly fractures, deformities, and reconstruction. In the past, RP has been hampered by cost and difficulties accessing the appropriate expertise. Here we outline the history of rapid prototyping and furthermore a process using open-source software to produce a high fidelity physical model from CT data. This greatly mitigates the expense associated with the technique, allowing surgeons to produce precise models for preoperative planning and procedure rehearsal. We describe the method with an illustrative case. PMID:22666160

A study of iron mineral transformation to reduce red mud tailings.

PubMed

Li, L Y

2001-01-01

This study examines the effects of iron mineral transformation in an aluminum extraction process on the settling behavior, and the physical and chemical properties of the resulting red mud slurry that must be disposed of. By producing a red mud with a higher solid content, the total volume of mud slurry will also be reduced for a given alumina production rate and more caustic soda will be recovered. The settling behavior and the mineralogical, physical, and physico-chemical properties of one bauxite and three red muds processed under varying conditions were analyzed based on examination of the iron mineral transformations. The properties of red muds derived from the same bauxite can differ markedly due to variations in operating conditions of the Bayer process, such as temperature and the addition of a reducing agent. The settling of red mud can be improved by converting goethite into hematite and/or magnetite to produce a mud of larger particle size, smaller specific surface area, and larger specific gravity, characteristics which reduce the total volume of mud slurry to be disposed of and which allow for less potential contamination from caustic soda. This study also found that the by-product--Bayer sodalite--has the high exchange capacity for Na+ that might contribute to the long-term environmental problems.

The environmental and medical geochemistry of potentially hazardous materials produced by disasters

USGS Publications Warehouse

Plumlee, Geoffrey S.; Morman, Suzette A.; Meeker, G.P.; Hoefen, Todd M.; Hageman, Philip L.; Wolf, Ruth E.

2014-01-01

Many natural or human-caused disasters release potentially hazardous materials (HM) that may pose threats to the environment and health of exposed humans, wildlife, and livestock. This chapter summarizes the environmentally and toxicologically significant physical, mineralogical, and geochemical characteristics of materials produced by a wide variety of recent disasters, such as volcanic eruptions, hurricanes and extreme storms, spills of mining/mineral-processing wastes or coal extraction by-products, and the 2001 attacks on and collapse of the World Trade Center towers. In describing these characteristics, this chapter also illustrates the important roles that geochemists and other earth scientists can play in environmental disaster response and preparedness. In addition to characterizing in detail the physical, chemical, and microbial makeup of HM generated by the disasters, these roles also include (1) identifying and discriminating potential multiple sources of the materials; (2) monitoring, mapping, and modeling dispersal and evolution of the materials in the environment; (3) understanding how the materials are modified by environmental processes; (4) identifying key characteristics and processes that influence the materials' toxicity to exposed humans and ecosystems; (5) estimating shifts away from predisaster environmental baseline conditions; and (6) using geochemical insights learned from past disasters to help estimate, prepare for, and increase societal resilience to the environmental and related health impacts of future disasters.

Recent progress in understanding the eruptions of classical novae

NASA Technical Reports Server (NTRS)

Shara, Michael M.

1988-01-01

Dramatic progress has occurred in the last two decades in understanding the physical processes and events leading up to, and transpiring during the eruption of a classical nova. The mechanism whereby a white dwarf accreting hydrogen-rich matter from a low-mass main-sequence companion produces a nova eruption has been understood since 1970. The mass-transferring binary stellar configuration leads inexorably to thermonuclear runaways detected at distances of megaparsecs. Summarized here are the efforts of many researchers in understanding the physical processes which generate nova eruptions; the effects upon nova eruptions of different binary-system parameters (e.g., chemical composition or mass of the white dwarf, different mass accretion rates); the possible metamorphosis from dwarf to classical novae and back again; and observational diagnostics of novae, including x ray and gamma ray emission, and the characteristics and distributions of novae in globular clusters and in extragalactic systems. While the thermonuclear-runaway model remains the successful cornerstone of nova simulation, it is now clear that a wide variety of physical processes, and three-dimensional hydrodynamic simulations, will be needed to explain the rich spectrum of behavior observed in erupting novae.

A Prescription for List-Mode Data Processing Conventions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beddingfield, David H.; Swinhoe, Martyn Thomas; Huszti, Jozsef

There are a variety of algorithmic approaches available to process list-mode pulse streams to produce multiplicity histograms for subsequent analysis. In the development of the INCC v6.0 code to include the processing of this data format, we have noted inconsistencies in the “processed time” between the various approaches. The processed time, tp, is the time interval over which the recorded pulses are analyzed to construct multiplicity histograms. This is the time interval that is used to convert measured counts into count rates. The observed inconsistencies in tp impact the reported count rate information and the determination of the error-values associatedmore » with the derived singles, doubles, and triples counting rates. This issue is particularly important in low count-rate environments. In this report we will present a prescription for the processing of list-mode counting data that produces values that are both correct and consistent with traditional shift-register technologies. It is our objective to define conventions for list mode data processing to ensure that the results are physically valid and numerically aligned with the results from shift-register electronics.« less

Lean production design using value stream mapping and ergonomics approach for waste elimination on buffing panel upright process

NASA Astrophysics Data System (ADS)

Suryoputro, M. R.; Sari, A. D.; Burhanudin, R.; Sugarindra, M.

2017-12-01

This study discussed the implementation of ergonomics and value stream mapping issues to reduce the existing waste in the process of buffing upright panel in the XYZ music manufacturing company. Aimed to identify the 9 waste based on the identification in terms of production processes and ergonomic factors, namely environmental health and safety, defects, overproduction, waiting, not utilizing employee knowledge skill and ability, transportation, inventory, motion, and excess process. In addition, ergonomics factors were identified, for example posture using REBA, job safety analysis, and physical workload. This study results indicated that the process is having 21.4% of the potential dangers that could not be accepted and thus potentially lead to lost time. Continued with the physical workload, the score of % cardiovascular load value is still below 30%, which means that the physical workload is normal and allows the addition of work. Meanwhile, in the calculation of posture investigation, the REBA resulted that there was a motion waste identified on the edge buff machine and ryoto with the score of 10 and 8. In conclusion, the results shown that there were 20 overall waste produced, then thus waste were reduced based on the identification and discussion of proposed improvements.

Two-dimensional patterns in bacterial veils arise from self-generated, three-dimensional fluid flows.

PubMed

Cogan, N G; Wolgemuth, C W

2011-01-01

The behavior of collections of oceanic bacteria is controlled by metabolic (chemotaxis) and physical (fluid motion) processes. Some sulfur-oxidizing bacteria, such as Thiovulum majus, unite these two processes via a material interface produced by the bacteria and upon which the bacteria are transiently attached. This interface, termed a bacterial veil, is formed by exo-polymeric substances (EPS) produced by the bacteria. By adhering to the veil while continuing to rotate their flagella, the bacteria are able to exert force on the fluid surroundings. This behavior induces a fluid flow that, in turn, causes the bacteria to aggregate leading to the formation of a physical pattern in the veil. These striking patterns are very similar in flavor to the classic convection instability observed when a shallow fluid is heated from below. However, the physics are very different since the flow around the veil is mediated by the bacteria and affects the bacterial densities. In this study, we extend a model of a one-dimensional veil in a two-dimensional fluid to the more realistic two-dimensional veil in a three-dimensional fluid. The linear stability analysis indicates that the Peclet number serves as a bifurcation parameter, which is consistent with experimental observations. We also solve the nonlinear problem numerically and are able to obtain patterns that are similar to those observed in the experiments.

Petascale Computing for Ground-Based Solar Physics with the DKIST Data Center

NASA Astrophysics Data System (ADS)

Berukoff, Steven J.; Hays, Tony; Reardon, Kevin P.; Spiess, DJ; Watson, Fraser; Wiant, Scott

2016-05-01

When construction is complete in 2019, the Daniel K. Inouye Solar Telescope will be the most-capable large aperture, high-resolution, multi-instrument solar physics facility in the world. The telescope is designed as a four-meter off-axis Gregorian, with a rotating Coude laboratory designed to simultaneously house and support five first-light imaging and spectropolarimetric instruments. At current design, the facility and its instruments will generate data volumes of 3 PB per year, and produce 107-109 metadata elements.The DKIST Data Center is being designed to store, curate, and process this flood of information, while providing association of science data and metadata to its acquisition and processing provenance. The Data Center will produce quality-controlled calibrated data sets, and make them available freely and openly through modern search interfaces and APIs. Documented software and algorithms will also be made available through community repositories like Github for further collaboration and improvement.We discuss the current design and approach of the DKIST Data Center, describing the development cycle, early technology analysis and prototyping, and the roadmap ahead. We discuss our iterative development approach, the underappreciated challenges of calibrating ground-based solar data, the crucial integration of the Data Center within the larger Operations lifecycle, and how software and hardware support, intelligently deployed, will enable high-caliber solar physics research and community growth for the DKIST's 40-year lifespan.

Security and Privacy in Cyber-Physical Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fink, Glenn A.; Edgar, Thomas W.; Rice, Theora R.

As you have seen from the previous chapters, cyber-physical systems (CPS) are broadly used across technology and industrial domains. While these systems enable process optimization and efficiency and allow previously impossible functionality, security and privacy are key concerns for their design, development, and operation. CPS have been key components utilized in some of the highest publicized security breaches over the last decade. In this chapter, we will look over the CPS described in the previous chapters from a security perspective. In this chapter, we explain classical information and physical security fundamentals in the context of CPS and contextualize them acrossmore » application domains. We give examples where the interplay of functionality and diverse communication can introduce unexpected vulnerabilities and produce larger impacts. We will discuss how CPS security and privacy is inherently different from that of pure cyber or physical systems and what may be done to secure these systems, considering their emergent cyber-physical properties. Finally, we will discuss security and privacy implications of merging infrastructural and personal CPS. Our hope is to impart the knowledge of what CPS security and privacy are, why they are important, and explain existing processes and challenges.« less

Effect of saliva on physical food properties in fat texture perception.

PubMed

Kupirovič, Urška Pivk; Elmadfa, Ibrahim; Juillerat, Marcel-Alexandre; Raspor, Peter

2017-04-13

Sensory properties of food drive our food choices and it is generally accepted that lipids greatly contribute to the sensory properties of many foods and consequently to eating pleasure. Many studies have investigated the mechanisms of the fat perception. Unfortunately they used a variety of methods and products, thereby making generalization very difficult. The mechanism of fat perception in oral cavity is combined of several processes. Lipid composition and its properties strongly influence food structure. During consumption food is exposed to a range of in-mouth processing steps. Oral sensation of fat texture changes with time, from a first bite to chewing, while mixing with saliva, up to swallowing and even after swallowing. The present work reviews many aspects of fat texture perception from physical chemistry to physiology. Understanding the underlying mechanisms of in-mouth lipid processing would provide new concepts to produce low-fat food products with full-fat perception.

Thermally driven advection for radioxenon transport from an underground nuclear explosion

NASA Astrophysics Data System (ADS)

Sun, Yunwei; Carrigan, Charles R.

2016-05-01

Barometric pumping is a ubiquitous process resulting in migration of gases in the subsurface that has been studied as the primary mechanism for noble gas transport from an underground nuclear explosion (UNE). However, at early times following a UNE, advection driven by explosion residual heat is relevant to noble gas transport. A rigorous measure is needed for demonstrating how, when, and where advection is important. In this paper three physical processes of uncertain magnitude (oscillatory advection, matrix diffusion, and thermally driven advection) are parameterized by using boundary conditions, system properties, and source term strength. Sobol' sensitivity analysis is conducted to evaluate the importance of all physical processes influencing the xenon signals. This study indicates that thermally driven advection plays a more important role in producing xenon signals than oscillatory advection and matrix diffusion at early times following a UNE, and xenon isotopic ratios are observed to have both time and spatial dependence.

Plan of production of MeV laser electron photons at SPring-8

NASA Astrophysics Data System (ADS)

Arimoto, Y.; Ohkuma, H.; Suzuki, S.; Tamura, K.; Kumagai, N.; Okajima, S.; Fujiwara, M.

2001-10-01

MeV photons at SPring-8 are produced by backward Compton scattering (BCS) of far infrared (FIR) laser photons from a 8 GeV electron beam. The MeV photons are a powerful probe to study nuclear physics, astro-nuclear physics, nuclear engineering, condensed matter physics, etc. owing to their attractive properties such as small emittance, high intensity, high polarization, etc. The 10 MeV photons which can be produced by the BCS process between the 8 GeV electron of SPring-8 storage ring and FIR laser photons with a wavelength of ~100 μm have a great advantage. Since energy loss of the electron due to the BCS process is smaller than energy acceptance of the storage ring (±160 MeV), the stored electron beam is not lost. A stable CO_2-pumped FIR laser with the wavelength of ~100 μm is practically using as a probe of plasma diagnostics at a nuclear fusion reactor. Furthermore, since the laser has many oscillations in wide wavelength region, the BCS photons in wide range can be obtained. We plan to produce the MeV laser electron photons by the BCS at SPring-8. For these purpose, we are now developing a high power CO_2-pumped FIR laser. Up to now ~1.5 watts CW laser action at a wavelength of 118.8 μm has been achieved. In this meeting, we will present a current status of the FIR laser system, a plan of construction of the test beam-line for the production of MeV photons at SPring-8, and future plan of this project.

Composite Golf Clubs

NASA Technical Reports Server (NTRS)

1976-01-01

Babcock & Wilcox Co. under a partnership with Marshall Space Flight Center, produced composite materials, originally from the shuttle program, for improving golf clubs. Company used Marshall Space Flight Center's data summary file summarizing typical processing techniques and mechanical and physical properties of graphite and boron- reinforced composite materials. Reinforced composites provide combination of shaft rigidity and flexibility that provide maximum distance.

The physics of biofilms—an introduction

NASA Astrophysics Data System (ADS)

Mazza, Marco G.

2016-05-01

Biofilms are complex, self-organized consortia of microorganisms that produce a functional, protective matrix of biomolecules. Physically, the structure of a biofilm can be described as an entangled polymer network which grows and changes under the effect of gradients of nutrients, cell differentiation, quorum sensing, bacterial motion, and interaction with the environment. Its development is complex, and constantly adapting to environmental stimuli. Here, we review the fundamental physical processes that govern the inception, growth and development of a biofilm. Two important mechanisms guide the initial phase in a biofilm life-cycle: (i) the cell motility near or at a solid interface, and (ii) the cellular adhesion. Both processes are crucial for initiating the colony and for ensuring its stability. A mature biofilm behaves as a viscoelastic fluid with a complex, history-dependent dynamics. We discuss progress and challenges in the determination of its physical properties. Experimental and theoretical methods are now available that aim at integrating the biofilm’s hierarchy of interactions, and the heterogeneity of composition and spatial structures. We also discuss important directions in which future work should be directed.

On the Principles of Building a Layered Intrusion

NASA Astrophysics Data System (ADS)

Marsh, B. D.

2009-12-01

An accurate and realistic understanding of all magmatic processes involves knowing the combined physical and chemical fundamentals governing the overall process. Magmatic processes involve such a vast array of sub-processes (e.g., heat and mass transfer, crystal growth, slurry transport and sorting, annealing, resorbtion, etc.) that rarely is there any single feature or measurement that can be safely inverted to solve the problem. And each event as in the formation of an intrusion must at some level for heuristic purposes be defined as an isolated event. This is commonly done without much forethought, as is the absolutely critical assumption of the initial conditions defining the beginning of the event. Almost without exception, it is the initial conditions that determine the outcome of the entire process in all physical and biological systems. Automobile factories produce motorized vehicles not water melons or chimpanzees. Nucleosynthesis of H and He always gives the same set of elements. The initial conditions of the magma giving rise to the end product for mafic layered systems are especially difficult to discern and must be bounded by observing simpler, real time magmatic and volcanic processes. Initial conditions come from posing a series of questions: What was the style and duration of filling? What was the rate of influx and final volume of each delivery of magma? What was the compositional variation and phenocryst content of the individual magmatic deliveries? If phenocrysts are present, were they sorted prior to injection during ascension? What was the original and ongoing shape of the magmatic reservoir? A failure to appreciate or answer such basic questions leads to vastly untenable evolutionary scenarios. Unrealistic initial conditions necessarily lead to unrealistic magmatic scenarios. There are certain safe starting points. Eruptive and emplacement fluxes are limited. The larger an intrusion is the longer it took to build and the longer to build the more varied are the deliveries in time, volume, and constitution. Instantaneous emplacement of crystal free magma are unlikely initial conditions for a large intrusion. The most realistic initial conditions are that intrusions are made of a combination of crystal poor and crystal-rich inputs. Examples abound of the outcomes of systems with clearly known initial conditions. The huge Sudbury magma was produced in 5 minutes at a temperature of 1700C. Clearly crystal free, it produced no layering whatsoever. Sills worldwide, regardless of size, approaching these initial conditions are similarly featureless. At the other extreme are the lava outputs of large volcanic systems like Kilauea. The ensuing lava lakes produced over months are filled with magma containing varied amounts of phenocrysts/xenocrysts and ultramafic layers are produced. Intrusions abound of all sizes that show the same characteristics. Ponding in crystal-laden sills forms layered systems with many of the features of large bodies. Rapid cooling preserves diagnostic textural relations lost to annealing in large bodies. Slow cooling promotes annealing to sharpen and accentuate the initial modal and cryptic layering. Initial conditions are fundamental to understanding the final product. Physical processes buttressed by chemistry mainly dominate magmatic systems.

The role of toxicological science in meeting the challenges and opportunities of hydraulic fracturing.

PubMed

Goldstein, Bernard D; Brooks, Bryan W; Cohen, Steven D; Gates, Alexander E; Honeycutt, Michael E; Morris, John B; Orme-Zavaleta, Jennifer; Penning, Trevor M; Snawder, John

2014-06-01

We briefly describe how toxicology can inform the discussion and debate of the merits of hydraulic fracturing by providing information on the potential toxicity of the chemical and physical agents associated with this process, individually and in combination. We consider upstream activities related to bringing chemical and physical agents to the site, on-site activities including drilling of wells and containment of agents injected into or produced from the well, and downstream activities including the flow/removal of hydrocarbon products and of produced water from the site. A broad variety of chemical and physical agents are involved. As the industry expands this has raised concern about the potential for toxicological effects on ecosystems, workers, and the general public. Response to these concerns requires a concerted and collaborative toxicological assessment. This assessment should take into account the different geology in areas newly subjected to hydraulic fracturing as well as evolving industrial practices that can alter the chemical and physical agents of toxicological interest. The potential for ecosystem or human exposure to mixtures of these agents presents a particular toxicological and public health challenge. These data are essential for developing a reliable assessment of the potential risks to the environment and to human health of the rapidly increasing use of hydraulic fracturing and deep underground horizontal drilling techniques for tightly bound shale gas and other fossil fuels. Input from toxicologists will be most effective when employed early in the process, before there are unwanted consequences to the environment and human health, or economic losses due to the need to abandon or rework costly initiatives.

The Role of Toxicological Science in Meeting the Challenges and Opportunities of Hydraulic Fracturing

PubMed Central

Goldstein, Bernard D.; Brooks, Bryan W.; Cohen, Steven D.; Gates, Alexander E.; Honeycutt, Michael E.; Morris, John B.; Orme-Zavaleta, Jennifer; Penning, Trevor M.; Snawder, John

2014-01-01

We briefly describe how toxicology can inform the discussion and debate of the merits of hydraulic fracturing by providing information on the potential toxicity of the chemical and physical agents associated with this process, individually and in combination. We consider upstream activities related to bringing chemical and physical agents to the site, on-site activities including drilling of wells and containment of agents injected into or produced from the well, and downstream activities including the flow/removal of hydrocarbon products and of produced water from the site. A broad variety of chemical and physical agents are involved. As the industry expands this has raised concern about the potential for toxicological effects on ecosystems, workers, and the general public. Response to these concerns requires a concerted and collaborative toxicological assessment. This assessment should take into account the different geology in areas newly subjected to hydraulic fracturing as well as evolving industrial practices that can alter the chemical and physical agents of toxicological interest. The potential for ecosystem or human exposure to mixtures of these agents presents a particular toxicological and public health challenge. These data are essential for developing a reliable assessment of the potential risks to the environment and to human health of the rapidly increasing use of hydraulic fracturing and deep underground horizontal drilling techniques for tightly bound shale gas and other fossil fuels. Input from toxicologists will be most effective when employed early in the process, before there are unwanted consequences to the environment and human health, or economic losses due to the need to abandon or rework costly initiatives. PMID:24706166

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goriely, S.; Bauswein, A.; Janka, H.-T.

About half of the nuclei heavier than iron observed in nature are produced by the so-called rapid neutron capture process, or r-process, of nucleosynthesis. The identification of the astrophysics site and the specific conditions in which the r-process takes place remains, however, one of the still-unsolved mysteries of modern astrophysics. Another underlying difficulty associated with our understanding of the r-process concerns the uncertainties in the predictions of nuclear properties for the few thousands exotic neutron-rich nuclei involved, for which essentially no experimental data exist. The present paper emphasizes some important future challenges faced by nuclear physics in this problem, particularlymore » in the determination of the nuclear structure properties of exotic neutron-rich nuclei as well as their radiative neutron capture rates and their fission probabilities. These quantities are particularly relevant to determine the composition of the matter resulting from the r-process. Both the astrophysics and the nuclear physics difficulties are critically reviewed with special attention paid to the r-process taking place during the decompression of neutron star matter following the merging of two neutron stars.« less

Two Complementary Strategies for New Physics Searches at Lepton Colliders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hooberman, Benjamin Henry

In this thesis I present two complementary strategies for probing beyond-the-Standard Model physics using data collected in e +e - collisions at lepton colliders. One strategy involves searching for effects at low energy mediated by new particles at the TeV mass scale, at which new physics is expected to manifest. Several new physics scenarios, including Supersymmetry and models with leptoquarks or compositeness, may lead to observable rates for charged lepton-flavor violating processes, which are forbidden in the Standard Model. I present a search for lepton-flavor violating decays of the Υ(3S) using data collected with the BABAR detector. This study establishesmore » the 90% confidence level upper limits BF(Υ(3S) → eτ) < 5.0 x 10 -6 and BF(Υ(3S) → μτ) < 4.1 x 10 -6 which are used to place constraints on new physics contributing to lepton-flavor violation at the TeV mass scale. An alternative strategy is to increase the collision energy above the threshold for new particles and produce them directly. I discuss research and development efforts aimed at producing a vertex tracker which achieves the physics performance required of a high energy lepton collider. A small-scale vertex tracker prototype is constructed using Silicon sensors of 50 μm thickness and tested using charged particle beams. This tracker achieves the targeted impact parameter resolution of σ LP = (5⊕10 GeV/p T) as well as a longitudinal vertex resolution of (260 ± 10) μm, which is consistent with the requirements of a TeV-scale lepton collider. This detector research and development effort must be motivated and directed by simulation studies of physics processes. Investigation of a dark matter-motivated Supersymmetry scenario is presented, in which the dark matter is composed of Supersymmetric neutralinos. In this scenario, studies of the e +e - → H 0A 0 production process allow for precise measurements of the properties of the A 0 Supersymmetric Higgs boson, which improve the achievable precision on the neutralino dark matter candidate relic density to 8%. Comparison between this quantity and the dark matter density determined from cosmological observations will further our understanding of dark matter by allowing us to determine if it is of Supersymmetric origin.« less

[Effect of naphthalan and therapeutic mud applications on clinical and roentgenological characteristics in patients with protracted pneumonia].

PubMed

Rassulova, M A; Siziakova, L A; Aĭrapetova, N S

2009-01-01

The influence of application of naftalan and therapeutic muds on clinical and roentgenological parameters, external respiration function, biochemical and immunological characteristics of the inflammatory process was studied in 82 patients presenting with protracted pneumonia and compared with the outcome of therapy using no physical factors. The application of naftalan and therapeutic muds was shown to reduce activity of inflammatory processes, improve airway patency and the state ofbronchial mucosa. Naftalan produced better therapeutic effect than muds.

Simulation of secondary emission calorimeter for future colliders

NASA Astrophysics Data System (ADS)

Yetkin, E. A.; Yetkin, T.; Ozok, F.; Iren, E.; Erduran, M. N.

2018-03-01

We present updated results from a simulation study of a conceptual sampling electromagnetic calorimeter based on secondary electron emission process. We implemented the secondary electron emission process in Geant4 as a user physics list and produced the energy spectrum and yield of secondary electrons. The energy resolution of the SEE calorimeter was σ/E = (41%) GeV1/2/√E and the response linearity to electromagnetic showers was to within 1.5%. The simulation results were also compared with a traditional scintillator calorimeter.

Synfuels from fusion: using the tandem mirror reactor and a thermochemical cycle to produce hydrogen

DOE Office of Scientific and Technical Information (OSTI.GOV)

Werner, R.W.

1982-11-01

This study is concerned with the following area: (1) the tandem mirror reactor and its physics; (2) energy balance; (3) the lithium oxide canister blanket system; (4) high-temperature blanket; (5) energy transport system-reactor to process; (6) thermochemical hydrogen processes; (7) interfacing the GA cycle; (8) matching power and temperature demands; (9) preliminary cost estimates; (10) synfuels beyond hydrogen; and (11) thermodynamics of the H/sub 2/SO/sub 4/-H/sub 2/O system. (MOW)

Chemical Vapor Deposited Zinc Sulfide. SPIE Press Monograph

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCloy, John S.; Tustison, Randal W.

2013-04-22

Zinc sulfide has shown unequaled utility for infrared windows that require a combination of long-wavelength infrared transparency, mechanical durability, and elevated-temperature performance. This book reviews the physical properties of chemical vapor deposited ZnS and their relationship to the CVD process that produced them. An in-depth look at the material microstructure is included, along with a discussion of the material's optical properties. Finally, because the CVD process itself is central to the development of this material, a brief history is presented.

Catalysts and methods for converting carbonaceous materials to fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hensley, Jesse; Ruddy, Daniel A.; Schaidle, Joshua A.

This disclosure relates to catalysts and processes designed to convert DME and/or methanol and hydrogen (H.sub.2) to desirable liquid fuels. These catalysts produce the fuels efficiently and with a high selectivity and yield, and reduce the formation of aromatic hydrocarbons by incorporating H.sub.2 into the products. This disclosure also describes process methods to further upgrade these fuels to higher molecular weight liquid fuel mixtures, which have physical properties comparable with current commercially used liquid fuels.

Design of multiple representations e-learning resources based on a contextual approach for the basic physics course

NASA Astrophysics Data System (ADS)

Bakri, F.; Muliyati, D.

2018-05-01

This research aims to design e-learning resources with multiple representations based on a contextual approach for the Basic Physics Course. The research uses the research and development methods accordance Dick & Carey strategy. The development carried out in the digital laboratory of Physics Education Department, Mathematics and Science Faculty, Universitas Negeri Jakarta. The result of the process of product development with Dick & Carey strategy, have produced e-learning design of the Basic Physics Course is presented in multiple representations in contextual learning syntax. The appropriate of representation used in the design of learning basic physics include: concept map, video, figures, data tables of experiment results, charts of data tables, the verbal explanations, mathematical equations, problem and solutions example, and exercise. Multiple representations are presented in the form of contextual learning by stages: relating, experiencing, applying, transferring, and cooperating.

The Physics of Semiconductors

NASA Astrophysics Data System (ADS)

Brennan, Kevin F.

1999-02-01

Modern fabrication techniques have made it possible to produce semiconductor devices whose dimensions are so small that quantum mechanical effects dominate their behavior. This book describes the key elements of quantum mechanics, statistical mechanics, and solid-state physics that are necessary in understanding these modern semiconductor devices. The author begins with a review of elementary quantum mechanics, and then describes more advanced topics, such as multiple quantum wells. He then disusses equilibrium and nonequilibrium statistical mechanics. Following this introduction, he provides a thorough treatment of solid-state physics, covering electron motion in periodic potentials, electron-phonon interaction, and recombination processes. The final four chapters deal exclusively with real devices, such as semiconductor lasers, photodiodes, flat panel displays, and MOSFETs. The book contains many homework exercises and is suitable as a textbook for electrical engineering, materials science, or physics students taking courses in solid-state device physics. It will also be a valuable reference for practicing engineers in optoelectronics and related areas.

Advances in postharvest technologies to extend the storage life of minimally processed fruits and vegetables.

PubMed

Ali, Asgar; Yeoh, Wei Keat; Forney, Charles; Siddiqui, Mohammed Wasim

2017-10-26

Minimally processed fresh produce is one of the fastest growing segments of the food industry due to consumer demand for fresh, healthy, and convenient foods. However, mechanical operations of cutting and peeling induce the liberation of cellular contents at the site of wounding that can promote the growth of pathogenic and spoilage microorganisms. In addition, rates of tissue senescence can be enhanced resulting in reduced storage life of fresh-cut fruits and vegetables. Chlorine has been widely adopted in the disinfection and washing procedures of fresh-cut produce due to its low cost and efficacy against a broad spectrum of microorganisms. Continuous replenishment of chlorine in high organic wash water can promote the formation of carcinogenic compounds such as trihalomethanes, which threaten human and environmental health. Alternative green and innovative chemical and physical postharvest treatments such as ozone, electrolyzed water, hydrogen peroxide, ultraviolet radiation, high pressure processing, and ultrasound can achieve similar reduction of microorganisms as chlorine without the production of harmful compounds or compromising the quality of fresh-cut produce.

Green Synthesis of Metallic Nanoparticles via Biological Entities

PubMed Central

Shah, Monaliben; Fawcett, Derek; Sharma, Shashi; Tripathy, Suraj Kumar; Poinern, Gérrard Eddy Jai

2015-01-01

Nanotechnology is the creation, manipulation and use of materials at the nanometre size scale (1 to 100 nm). At this size scale there are significant differences in many material properties that are normally not seen in the same materials at larger scales. Although nanoscale materials can be produced using a variety of traditional physical and chemical processes, it is now possible to biologically synthesize materials via environment-friendly green chemistry based techniques. In recent years, the convergence between nanotechnology and biology has created the new field of nanobiotechnology that incorporates the use of biological entities such as actinomycetes algae, bacteria, fungi, viruses, yeasts, and plants in a number of biochemical and biophysical processes. The biological synthesis via nanobiotechnology processes have a significant potential to boost nanoparticles production without the use of harsh, toxic, and expensive chemicals commonly used in conventional physical and chemical processes. The aim of this review is to provide an overview of recent trends in synthesizing nanoparticles via biological entities and their potential applications. PMID:28793638

Progress on China nuclear data processing code system

NASA Astrophysics Data System (ADS)

Liu, Ping; Wu, Xiaofei; Ge, Zhigang; Li, Songyang; Wu, Haicheng; Wen, Lili; Wang, Wenming; Zhang, Huanyu

2017-09-01

China is developing the nuclear data processing code Ruler, which can be used for producing multi-group cross sections and related quantities from evaluated nuclear data in the ENDF format [1]. The Ruler includes modules for reconstructing cross sections in all energy range, generating Doppler-broadened cross sections for given temperature, producing effective self-shielded cross sections in unresolved energy range, calculating scattering cross sections in thermal energy range, generating group cross sections and matrices, preparing WIMS-D format data files for the reactor physics code WIMS-D [2]. Programming language of the Ruler is Fortran-90. The Ruler is tested for 32-bit computers with Windows-XP and Linux operating systems. The verification of Ruler has been performed by comparison with calculation results obtained by the NJOY99 [3] processing code. The validation of Ruler has been performed by using WIMSD5B code.

Competency based teaching of college physics: The philosophy and the practice

NASA Astrophysics Data System (ADS)

Rajapaksha, Ajith; Hirsch, Andrew S.

2017-12-01

The practice of learning physics contributes to the development of many transdisciplinary skills learners are able to exercise independent of the physics discipline. However, the standard practices of physics instruction do not explicitly include the monitoring or evaluation of these skills. In a competency-based (CB) learning model, the skills (competencies) are clearly defined and evaluated. We envisioned that a CB approach, where the underlying competencies are highlighted within the instructional process, would be more suitable to teaching physics to learners with diversified disciplinary interests. A model CB course curriculum was developed and practiced at Purdue University to teach introductory college physics to learners who were majoring in the technology disciplines. The experiment took place from the spring semester in 2015 until the spring semester in 2017. The practice provided a means to monitor and evaluate a set of developmental transdisciplinary competencies that underlie the learning of force and motion concepts in classical physics. Additionally, the CB practice contributed to produce substantial physics learning outcomes among learners who were underprepared to learn physics in college.

Nanoporous Silicon Carbide for Nanoelectromechanical Systems Applications

NASA Technical Reports Server (NTRS)

Hossain, T.; Khan, F.; Adesida, I.; Bohn, P.; Rittenhouse, T.; Lienhard, Michael (Technical Monitor)

2003-01-01

A major goal of this project is to produce porous silicon carbide (PSiC) via an electroless process for eventual utilization in nanoscale sensing platforms. Results in the literature have shown a variety of porous morphologies in SiC produced in anodic cells. Therefore, predictability and reproducibility of porous structures are initial concerns. This work has concentrated on producing morphologies of known porosity, with particular attention paid toward producing the extremely high surface areas required for a porous flow sensor. We have conducted a parametric study of electroless etching conditions and characteristics of the resulting physical nanostructure and also investigated the relationship between morphology and materials properties. Further, we have investigated bulk etching of SiC using both photo-electrochemical etching and inductively-coupled-plasma reactive ion etching techniques.

A Review of Metal Injection Molding- Process, Optimization, Defects and Microwave Sintering on WC-Co Cemented Carbide

NASA Astrophysics Data System (ADS)

Shahbudin, S. N. A.; Othman, M. H.; Amin, Sri Yulis M.; Ibrahim, M. H. I.

2017-08-01

This article is about a review of optimization of metal injection molding and microwave sintering process on tungsten cemented carbide produce by metal injection molding process. In this study, the process parameters for the metal injection molding were optimized using Taguchi method. Taguchi methods have been used widely in engineering analysis to optimize the performance characteristics through the setting of design parameters. Microwave sintering is a process generally being used in powder metallurgy over the conventional method. It has typical characteristics such as accelerated heating rate, shortened processing cycle, high energy efficiency, fine and homogeneous microstructure, and enhanced mechanical performance, which is beneficial to prepare nanostructured cemented carbides in metal injection molding. Besides that, with an advanced and promising technology, metal injection molding has proven that can produce cemented carbides. Cemented tungsten carbide hard metal has been used widely in various applications due to its desirable combination of mechanical, physical, and chemical properties. Moreover, areas of study include common defects in metal injection molding and application of microwave sintering itself has been discussed in this paper.

Optimization of physical conditions for the production of thermostable T1 lipase in Pichia guilliermondii strain SO using response surface methodology.

PubMed

Abu, Mary Ladidi; Nooh, Hisham Mohd; Oslan, Siti Nurbaya; Salleh, Abu Bakar

2017-11-10

Pichia guilliermondii was found capable of expressing the recombinant thermostable lipase without methanol under the control of methanol dependent alcohol oxidase 1 promoter (AOXp 1). In this study, statistical approaches were employed for the screening and optimisation of physical conditions for T1 lipase production in P. guilliermondii. The screening of six physical conditions by Plackett-Burman Design has identified pH, inoculum size and incubation time as exerting significant effects on lipase production. These three conditions were further optimised using, Box-Behnken Design of Response Surface Methodology, which predicted an optimum medium comprising pH 6, 24 h incubation time and 2% inoculum size. T1 lipase activity of 2.0 U/mL was produced with a biomass of OD 600 23.0. The process of using RSM for optimisation yielded a 3-fold increase of T1 lipase over medium before optimisation. Therefore, this result has proven that T1 lipase can be produced at a higher yield in P. guilliermondii.

Preschool physics: Using the invisible property of weight in causal reasoning tasks

PubMed Central

Williamson, Rebecca A.; Meltzoff, Andrew N.

2018-01-01

Causal reasoning is an important aspect of scientific thinking. Even young human children can use causal reasoning to explain observations, make predictions, and design actions to bring about specific outcomes in the physical world. Weight is an interesting type of cause because it is an invisible property. Here, we tested preschool children with causal problem-solving tasks that assessed their understanding of weight. In an experimental setting, 2- to 5-year-old children completed three different tasks in which they had to use weight to produce physical effects—an object displacement task, a balance-scale task, and a tower-building task. The results showed that the children’s understanding of how to use object weight to produce specific object-to-object causal outcomes improved as a function of age, with 4- and 5-year-olds showing above-chance performance on all three tasks. The younger children’s performance was more variable. The pattern of results provides theoretical insights into which aspects of weight processing are particularly difficult for preschool children and why they find it difficult. PMID:29561840

First results of transcritical magnetized collisionless shock studies on MSX

NASA Astrophysics Data System (ADS)

Weber, T. E.; Smith, R. J.; Hutchinson, T. M.; Taylor, S. F.; Hsu, S. C.

2014-10-01

Magnetized collisionless shocks exhibit transitional length and time scales much shorter than can be created through collisional processes. They are common throughout the cosmos, but have historically proven difficult to create in the laboratory. The Magnetized Shock Experiment (MSX) at LANL produces super-Alfvénic shocks through the acceleration and subsequent stagnation of Field Reversed Configuration (FRC) plasmoids against a strong magnetic mirror and flux-conserving vacuum boundary. Plasma flows have been produced with sonic and Alfvén Mach numbers up to ~10 over a wide range of plasma beta with embedded perpendicular, oblique, and parallel magnetic field. Macroscopic ion skin-depth and long ion-gyroperiod enable diagnostic access to relevant shock physics using common methods. Variable plasmoid velocity, density, temperature, and magnetic field provide access to a wide range of shock conditions, and a campaign to study the physics of transcritical and supercritical shocks within the FRC plasmoid is currently underway. An overview of the experimental design, diagnostics suite, physics objectives, and recent results will be presented. Supported by DOE Office of Fusion Energy Sciences under DOE Contract DE-AC52-06NA25369.

Preschool physics: Using the invisible property of weight in causal reasoning tasks.

PubMed

Wang, Zhidan; Williamson, Rebecca A; Meltzoff, Andrew N

2018-01-01

Causal reasoning is an important aspect of scientific thinking. Even young human children can use causal reasoning to explain observations, make predictions, and design actions to bring about specific outcomes in the physical world. Weight is an interesting type of cause because it is an invisible property. Here, we tested preschool children with causal problem-solving tasks that assessed their understanding of weight. In an experimental setting, 2- to 5-year-old children completed three different tasks in which they had to use weight to produce physical effects-an object displacement task, a balance-scale task, and a tower-building task. The results showed that the children's understanding of how to use object weight to produce specific object-to-object causal outcomes improved as a function of age, with 4- and 5-year-olds showing above-chance performance on all three tasks. The younger children's performance was more variable. The pattern of results provides theoretical insights into which aspects of weight processing are particularly difficult for preschool children and why they find it difficult.

Analysis of the 20th November 2003 Extreme Geomagnetic Storm using CTIPe Model and GNSS Data

NASA Astrophysics Data System (ADS)

Fernandez-Gomez, I.; Borries, C.; Codrescu, M.

2016-12-01

The ionospheric instabilities produced by solar activity generate disturbances in ionospheric density (ionospheric storms) with important terrestrial consequences such as disrupting communications and positioning. During the 20th November 2003 extreme geomagnetic storm, significant perturbations were produced in the ionosphere - thermosphere system. In this work, we replicate how this system responded to the onset of this particular storm, using the Coupled Thermosphere Ionosphere Plasmasphere electrodynamics physics based model. CTIPe simulates the changes in the neutral winds, temperature, composition and electron densities. Although modelling the ionosphere under this conditions is a challenging task due to energy flow uncertainties, the model reproduces some of the storm features necessary to interpret the physical mechanisms behind the Total Electron Content (TEC) increase and the dramatic changes in composition during this event.Corresponding effects are observed in the TEC simulations from other physics based models and from observations derived from Global Navigation Satellite System (GNSS) and ground-based measurements.The study illustrates the necessity of using both, measurements and models, to have a complete understanding of the processes that are most likely responsible for the observed effects.

Physical and visual state of 100-year-old Lippman color photographs

NASA Astrophysics Data System (ADS)

Alschuler, William R.

1998-02-01

In 1891 Gabriel Lippmann demonstrated a photographic process which records full color images on black and white emulsions. It is closely related to Denisyuk's reflection holography technique, which he named after Lippmann. After a historical introduction I will speak on the physical state and visual appearance of Lippmann-process color images produced at the turn of the century by Lippmann and a limited number of other practitioners. Images made on albumin, collodion and gelatine will be discussed, based on my examination of more than 400 images held in public and private collections. Examples of old original images (and some new work) will be shown. It is possible to conclude that, if properly excited, such images will be stable in their beautiful rendition of color and extremely high resolution almost indefinitely.

Predictive modeling of solidification during laser additive manufacturing of nickel superalloys: recent developments, future directions

NASA Astrophysics Data System (ADS)

Ghosh, Supriyo

2018-01-01

Additive manufacturing (AM) processes produce parts with improved physical, chemical, and mechanical properties compared to conventional manufacturing processes. In AM processes, intricate part geometries are produced from multicomponent alloy powder, in a layer-by-layer fashion with multipass laser melting, solidification, and solid-state phase transformations, in a shorter manufacturing time, with minimal surface finishing, and at a reasonable cost. However, there is an increasing need for post-processing of the manufactured parts via, for example, stress relieving heat treatment and hot isostatic pressing to achieve homogeneous microstructure and properties at all times. Solidification in an AM process controls the size, shape, and distribution of the grains, the growth morphology, the elemental segregation and precipitation, the subsequent solid-state phase changes, and ultimately the material properties. The critical issues in this process are linked with multiphysics (such as fluid flow and diffusion of heat and mass) and multiscale (lengths, times and temperature ranges) challenges that arise due to localized rapid heating and cooling during AM processing. The alloy chemistry-process-microstructure-property-performance correlation in this process will be increasingly better understood through multiscale modeling and simulation.

Wet-air oxidation cleans up black wastewater

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-09-01

Sterling Organics produces the analgesic paracetamol (acetaminophen) at its Dudley, England, plant. The wastewater from the batch process contains intermediates such as para-aminophenol (PAP) and byproducts such as thiosulfates, sulfites and sulfides. To stay ahead of increasingly strict environmental legislation, Sterling Organics installed a wet-air oxidation system at the Dudley facility in August 1992. The system is made by Zimpro Environmental Inc. (Rothschild, Wis.). Zimpro's wet-air oxidation system finds a way around the limitations of purely chemical or physical processes. In the process, compressed air at elevated temperature and pressure oxidizes the process intermediates and byproducts and removes the colormore » from the wastewater.« less

From ancient Greece to the cognitive revolution: A comprehensive view of physical rehabilitation sciences.

PubMed

Martínez-Pernía, David; González-Castán, Óscar; Huepe, David

2017-02-01

The development of rehabilitation has traditionally focused on measurements of motor disorders and measurements of the improvements produced during the therapeutic process; however, physical rehabilitation sciences have not focused on understanding the philosophical and scientific principles in clinical intervention and how they are interrelated. The main aim of this paper is to explain the foundation stones of the disciplines of physical therapy, occupational therapy, and speech/language therapy in recovery from motor disorder. To reach our goals, the mechanistic view and how it is integrated into physical rehabilitation will first be explained. Next, a classification into mechanistic therapy based on an old version (automaton model) and a technological version (cyborg model) will be shown. Then, it will be shown how physical rehabilitation sciences found a new perspective in motor recovery, which is based on functionalism, during the cognitive revolution in the 1960s. Through this cognitive theory, physical rehabilitation incorporated into motor recovery of those therapeutic strategies that solicit the activation of the brain and/or symbolic processing; aspects that were not taken into account in mechanistic therapy. In addition, a classification into functionalist rehabilitation based on a computational therapy and a brain therapy will be shown. At the end of the article, the methodological principles in physical rehabilitation sciences will be explained. It will allow us to go deeper into the differences and similarities between therapeutic mechanism and therapeutic functionalism.

The sustainable growth of the first black holes

NASA Astrophysics Data System (ADS)

Pezzulli, Edwige; Volonteri, Marta; Schneider, Raffaella; Valiante, Rosa

2017-10-01

Super-Eddington accretion has been suggested as a possible formation pathway of 109 M⊙ supermassive black holes (SMBHs) 800 Myr after the big bang. However, stellar feedback from BH seed progenitors and winds from BH accretion discs may decrease BH accretion rates. In this work, we study the impact of these physical processes on the formation of z ˜ 6 quasar, including new physical prescriptions in the cosmological, data-constrained semi-analytic model GAMETE/QSOdust. We find that the feedback produced by the first stellar progenitors on the surrounding does not play a relevant role in preventing SMBHs formation. In order to grow the z ≳ 6 SMBHs, the accreted gas must efficiently lose angular momentum. Moreover, disc winds, easily originated in super-Eddington accretion regime, can strongly reduce duty cycles. This produces a decrease in the active fraction among the progenitors of z ˜ 6 bright quasars, reducing the probability to observe them.

Extreme plasma states in laser-governed vacuum breakdown.

PubMed

Efimenko, Evgeny S; Bashinov, Aleksei V; Bastrakov, Sergei I; Gonoskov, Arkady A; Muraviev, Alexander A; Meyerov, Iosif B; Kim, Arkady V; Sergeev, Alexander M

2018-02-05

Triggering vacuum breakdown at laser facility is expected to provide rapid electron-positron pair production for studies in laboratory astrophysics and fundamental physics. However, the density of the produced plasma may cease to increase at a relativistic critical density, when the plasma becomes opaque. Here, we identify the opportunity of breaking this limit using optimal beam configuration of petawatt-class lasers. Tightly focused laser fields allow generating plasma in a small focal volume much less than λ 3 and creating extreme plasma states in terms of density and produced currents. These states can be regarded to be a new object of nonlinear plasma physics. Using 3D QED-PIC simulations we demonstrate a possibility of reaching densities over 10 25  cm -3 , which is an order of magnitude higher than expected earlier. Controlling the process via initial target parameters provides an opportunity to reach the discovered plasma states at the upcoming laser facilities.

Fashion, novelty and optimality: an application from Physics

NASA Astrophysics Data System (ADS)

Galam, Serge; Vignes, Annick

2005-06-01

We apply a physical-based model to describe the clothes fashion market. Every time a new outlet appears on the market, it can invade the market under certain specific conditions. Hence, the “old” outlet can be completely dominated and disappears. Each creator competes for a finite population of agents. Fashion phenomena are shown to result from a collective phenomenon produced by local individual imitation effects. We assume that, in each step of the imitation process, agents only interact with a subset rather than with the whole set of agents. People are actually more likely to influence (and be influenced by) their close “neighbors”. Accordingly, we discuss which strategy is best fitted for new producers when people are either simply organized into anonymous reference groups or when they are organized in social groups hierarchically ordered. While counterfeits are shown to reinforce the first strategy, creating social leaders can permit to avoid them.

Overview and recent progress of the Magnetized Shock Experiment (MSX)

NASA Astrophysics Data System (ADS)

Weber, T. E.; Intrator, T. P.; Smith, R. J.; Hutchinson, T. M.; Boguski, J. C.; Sears, J. A.; Swan, H. O.; Gao, K. W.; Chapdelaine, L. J.; Winske, D.; Dunn, J. P.

2013-10-01

The Magnetized Shock Experiment (MSX) has been constructed to study the physics of super-Alfvènic, supercritical, magnetized shocks. Exhibiting transitional length and time scales much smaller than can be produced through collisional processes, these shocks are observed to create non-thermal distributions, amplify magnetic fields, and accelerate particles to relativistic velocities. Shocks are produced through the acceleration and subsequent stagnation of Field Reversed Configuration (FRC) plasmoids against a high-flux magnetic mirror with a conducting boundary or a plasma target with embedded field. Adjustable shock velocity, density, and magnetic geometry (B parallel, perpendicular, or oblique to k) provide unique access to a wide range of dimensionless parameters relevant to astrophysical shocks. Information regarding the experimental configuration, diagnostics suite, recent simulations, experimental results, and physics goals will be presented. This work is supported by DOE OFES and NNSA under LANS contract DE-AC52-06NA25369 Approved for Public Release: LA-UR-13-24859.

Non-flammable polyimide materials for aircraft and spacecraft applications

NASA Technical Reports Server (NTRS)

Gagliani, J.; Supkis, D. E.

1979-01-01

Recent developments in polyimide chemistry show promise for producing materials with very low flammability and a wide range of mechanical properties. Polyimide foams can be synthesized to provide fire safety without detectable formation of smoke or toxic byproducts below 204 C (400 F), thus avoiding an environment which is lethal to human habitation. This work has been and is currently being performed under development programs, the objective of which is to provide cost effective processes for producing thermally stable, polyimide flexible resilient foams, thermal-acoustical insulating materials, rigid low density foam panels, and high strength foam structures. The chemical and physical properties demonstrated by these materials represent a technological advancement in the art of thermally stable polyimide polymers which are expected to insure fire protection of structures and components used in air transportation and space exploration. Data compiled to date on thermal, physical and functional properties of these materials are presented.

Plasma Spray-PVD: A New Thermal Spray Process to Deposit Out of the Vapor Phase

NASA Astrophysics Data System (ADS)

von Niessen, Konstantin; Gindrat, Malko

2011-06-01

Plasma spray-physical vapor deposition (PS-PVD) is a low pressure plasma spray technology recently developed by Sulzer Metco AG (Switzerland). Even though it is a thermal spray process, it can deposit coatings out of the vapor phase. The basis of PS-PVD is the low pressure plasma spraying (LPPS) technology that has been well established in industry for several years. In comparison to conventional vacuum plasma spraying (VPS) or low pressure plasma spraying (LPPS), the new proposed process uses a high energy plasma gun operated at a reduced work pressure of 0.1 kPa (1 mbar). Owing to the high energy plasma and further reduced work pressure, PS-PVD is able to deposit a coating not only by melting the feed stock material which builds up a layer from liquid splats but also by vaporizing the injected material. Therefore, the PS-PVD process fills the gap between the conventional physical vapor deposition (PVD) technologies and standard thermal spray processes. The possibility to vaporize feedstock material and to produce layers out of the vapor phase results in new and unique coating microstructures. The properties of such coatings are superior to those of thermal spray and electron beam-physical vapor deposition (EB-PVD) coatings. In contrast to EB-PVD, PS-PVD incorporates the vaporized coating material into a supersonic plasma plume. Owing to the forced gas stream of the plasma jet, complex shaped parts such as multi-airfoil turbine vanes can be coated with columnar thermal barrier coatings using PS-PVD. Even shadowed areas and areas which are not in the line of sight of the coating source can be coated homogeneously. This article reports on the progress made by Sulzer Metco in developing a thermal spray process to produce coatings out of the vapor phase. Columnar thermal barrier coatings made of Yttria-stabilized Zircona (YSZ) are optimized to serve in a turbine engine. This process includes not only preferable coating properties such as strain tolerance and erosion resistance but also the simultaneous coverage of multiple air foils.

Land Use and Change

NASA Technical Reports Server (NTRS)

Irwin, Daniel E.

2004-01-01

The overall purpose of this training session is to familiarize Central American project cooperators with the remote sensing and image processing research that is being conducted by the NASA research team and to acquaint them with the data products being produced in the areas of Land Cover and Land Use Change and carbon modeling under the NASA SERVIR project. The training session, therefore, will be both informative and practical in nature. Specifically, the course will focus on the physics of remote sensing, various satellite and airborne sensors (Landsat, MODIS, IKONOS, Star-3i), processing techniques, and commercial off the shelf image processing software.

Process engineering concerns in the lunar environment

NASA Technical Reports Server (NTRS)

Sullivan, T. A.

1990-01-01

The paper discusses the constraints on a production process imposed by the lunar or Martian environment on the space transportation system. A proposed chemical route to produce oxygen from iron oxide bearing minerals (including ilmenite) is presented in three different configurations which vary in complexity. A design for thermal energy storage is presented that could both provide power during the lunar night and act as a blast protection barrier for the outpost. A process to release carbon from the lunar regolith as methane is proposed, capitalizing on the greater abundance and favorable physical properties of methane relative to hydrogen to benefit the entire system.

Hot-isostatically pressed wasteforms for Magnox sludge immobilisation

NASA Astrophysics Data System (ADS)

Heath, Paul G.; Stewart, Martin W. A.; Moricca, Sam; Hyatt, Neil C.

2018-02-01

Thermal treatment technologies offer many potential benefits for the treatment of radioactive wastes including the passivation of reactive species and significant waste volume reductions. This paper presents a study investigating the production of wasteforms using Hot-isostatic pressing technology for the immobilisation of Magnox sludges from the UK's Sellafield Site. Simulants considered physically representative of these sludges were used to determine possible processing parameters and to determine the phase assemblages and morphologies produced during processing. The study showed hot-isostatic pressing is capable of processing Magnox sludges at up to 60 wt% (oxide basis) into dense, mixed ceramic wasteforms. The wasteforms produced are a glass-bonded ceramic of mixed magnesium titanates, encapsulating localised grains of periclase. The ability to co-process Magnox sludges with SIXEP sand/clinoptilolite slurries has also been demonstrated. The importance of these results is presented through a comparison of volume reduction data, which shows HIPing may provide a 20-fold volume reduction over the current cementitious baseline and double the volume reduction attainable for vitrification technologies.

Physical Properties of Nyamplung Oil (Calophyllum inophyllum L) for Biodiesel Production

NASA Astrophysics Data System (ADS)

Dewang, Syamsir; Suriani; Hadriani, Siti; Bannu; Abdullah, B.

2017-05-01

Worldwide energy crisis due to the too high of energy consumption causes the people trying to find alternative energy to support energy requirements. The use of energy from environmentally friendly plant-based materials into an effort to assist communities in sufficient of national energy needs. Some processing of Nyamplung (Calophyllum inophyllum L) oil production is drying and pressing to produce crude oil. Degumming process is then performed to remove the sap contained in the oil. The next process is to remove free fatty acids (FFA) below 2% that can cause corrosion on the machine when in use. The results performed of the density properties quality to produce oil that appropriate with the international standards by time variation of catalyst. The result was obtained the density value of 0.92108 gr/cm3 at the time of 3 hours by trans-esterification process, and the best yield value was measured at 98.2% in 2 hours stirring of transesterification.

Fluid Dynamics of Human Phonation and Speech

NASA Astrophysics Data System (ADS)

Mittal, Rajat; Erath, Byron D.; Plesniak, Michael W.

2013-01-01

This article presents a review of the fluid dynamics, flow-structure interactions, and acoustics associated with human phonation and speech. Our voice is produced through the process of phonation in the larynx, and an improved understanding of the underlying physics of this process is essential to advancing the treatment of voice disorders. Insights into the physics of phonation and speech can also contribute to improved vocal training and the development of new speech compression and synthesis schemes. This article introduces the key biomechanical features of the laryngeal physiology, reviews the basic principles of voice production, and summarizes the progress made over the past half-century in understanding the flow physics of phonation and speech. Laryngeal pathologies, which significantly enhance the complexity of phonatory dynamics, are discussed. After a thorough examination of the state of the art in computational modeling and experimental investigations of phonatory biomechanics, we present a synopsis of the pacing issues in this arena and an outlook for research in this fascinating subject.

The use of smoke acid as an alternative coagulating agent for natural rubber sheets' production.

PubMed

Ferreira, Vanda S; Rêgo, Ione N C; Pastore, Floriano; Mandai, Mariana M; Mendes, Leonardo S; Santos, Karin A M; Rubim, Joel C; Suarez, Paulo A Z

2005-03-01

A comparative study of rubber sheets obtained using formic, acetic, and smoke acid as coagulants is shown for latex obtained from native Amazonian trees and also from commercial cultivated trees. The evaluation of both processes of coagulation was carried out by spectroscopic and physical-chemical analysis, showing no differences in the rubber sheets obtained. This new method of rubber sheet preparation was introduced into Amazonian rainforest rubber tapper communities, which are actually producing in large scale. The physical-mechanical properties were similar among a large sheets made by different rubber tapper communities using this new method.

Localization and physical properties experiments conducted by Spirit at Gusev crater

USGS Publications Warehouse

Arvidson, R. E.; Anderson, R.C.; Bartlett, P.; Bell, J.F.; Blaney, D.; Christensen, P.R.; Chu, P.; Crumpler, L.; Davis, K.; Ehlmann, B.L.; Fergason, R.; Golombek, M.P.; Gorevan, S.; Grant, J. A.; Greeley, R.; Guinness, E.A.; Haldemann, A.F.C.; Herkenhoff, K.; Johnson, J.; Landis, G.; Li, R.; Lindemann, R.; McSween, H.; Ming, D. W.; Myrick, T.; Richter, L.; Seelos, F.P.; Squyres, S. W.; Sullivan, R.J.; Wang, A.; Wilson, Jim

2004-01-01

The precise location and relative elevation of Spirit during its traverses from the Columbia Memorial station to Bonneville crater were determined with bundle-adjusted retrievals from rover wheel turns, suspension and tilt angles, and overlapping images. Physical properties experiments show a decrease of 0.2% per Mars solar day in solar cell output resulting from deposition of airborne dust, cohesive soil-like deposits in plains and hollows, bright and dark rock coatings, and relatively weak volcanic rocks of basaltic composition. Volcanic, impact, aeolian, and water-related processes produced the encountered landforms and materials.

Localization and physical properties experiments conducted by Spirit at Gusev Crater.

PubMed

Arvidson, R E; Anderson, R C; Bartlett, P; Bell, J F; Blaney, D; Christensen, P R; Chu, P; Crumpler, L; Davis, K; Ehlmann, B L; Fergason, R; Golombek, M P; Gorevan, S; Grant, J A; Greeley, R; Guinness, E A; Haldemann, A F C; Herkenhoff, K; Johnson, J; Landis, G; Li, R; Lindemann, R; McSween, H; Ming, D W; Myrick, T; Richter, L; Seelos, F P; Squyres, S W; Sullivan, R J; Wang, A; Wilson, J

2004-08-06

The precise location and relative elevation of Spirit during its traverses from the Columbia Memorial station to Bonneville crater were determined with bundle-adjusted retrievals from rover wheel turns, suspension and tilt angles, and overlapping images. Physical properties experiments show a decrease of 0.2% per Mars solar day in solar cell output resulting from deposition of airborne dust, cohesive soil-like deposits in plains and hollows, bright and dark rock coatings, and relatively weak volcanic rocks of basaltic composition. Volcanic, impact, aeolian, and water-related processes produced the encountered landforms and materials.

Fast Simulation of the Impact Parameter Calculation of Electrons through Pair Production

NASA Astrophysics Data System (ADS)

Bang, Hyesun; Kweon, MinJung; Huh, Kyoung Bum; Pachmayer, Yvonne

2018-05-01

A fast simulation method is introduced that reduces tremendously the time required for the impact parameter calculation, a key observable in physics analyses of high energy physics experiments and detector optimisation studies. The impact parameter of electrons produced through pair production was calculated considering key related processes using the Bethe-Heitler formula, the Tsai formula and a simple geometric model. The calculations were performed at various conditions and the results were compared with those from full GEANT4 simulations. The computation time using this fast simulation method is 104 times shorter than that of the full GEANT4 simulation.

Application of nuclear physics in medical physics and nuclear medicine

NASA Astrophysics Data System (ADS)

Hoehr, Cornelia

2016-09-01

Nuclear physics has a long history of influencing and advancing medical fields. At TRIUMF we use the applications of nuclear physics to diagnose several diseases via medical isotopes and treat cancer by using proton beams. The Life Science division has a long history of producing Positron Emission Tomography (PET) isotopes but we are also investigating the production of SPECT and PET isotopes with a potential shortage for clinical operation or otherwise limited access to chemists, biologists and medical researchers. New targets are being developed, aided by a simulation platform investigating the processes inside a target under proton irradiation - nuclear, thermodynamic, and chemical. Simulations also aid in the development of new beam-shaping devices for TRIUMF's Proton Therapy facility, Canada's only proton therapy facility, as well as new treatment testing systems. Both promise improved treatment delivery for cancer patients.

Insights of Mixing on the Assembly of DNA Nanoparticles

NASA Astrophysics Data System (ADS)

Williams, Manda S.

Size is a crucial parameter in the delivery of nanoparticle therapeutics, affecting mechanisms such as tissue delivery, clearance, and cellular uptake. The morphology of nanoparticles is dependent both upon chemistry and the physical process of assembly. Polyplexes, a major class of non-viral gene delivery vectors, are conventionally prepared by vortex mixing, resulting in non-uniform nanoparticles and poor reproducibility. Better understanding and control of the physical process of assembly, and mixing in particular, will produce polyplexes of a more uniform and reliable size, optimizing their efficiency for laboratory and clinical use. "Mixing" is the reduction of length scale of a system to accelerate diffusion until a uniform concentration is achieved. Vortex mixing is poorly characterized and sensitive to protocols. Microfluidic systems are notable for predictable fluid behavior, and are ideal for analyzing and controlling the physical interaction of reagents on the microscale, realm where mixing occurs. Several microdevices for the preparation of DNA polyplexes are explored here. Firstly, the staggered herringbone mixer, a chaotic advection micromixer, is used to observe the effects of mixing time on nanoparticle size. Next, a novel device to surround the reagent flows with a sheath of buffer, preventing interaction with the walls and confining the complexation to a zone of lower, less variable shear and residence time, is used to demonstrate the role of shear in nanoparticle assembly. Lastly, uneven diffusion between ion pairs produces a small separation of charge at fluid interfaces; this short-lived electric field has a significant impact on the transport of DNA over the time scales of mixing and complexation. The effects of common buffers on the transport of DNA are examined for possible applications to mixing and complexation. These three investigations demonstrate the importance of the physical process in polyplex assembly, and indicate several important considerations in the development of new protocols and devices.

Flavour physics and the Large Hadron Collider beauty experiment.

PubMed

Gibson, Valerie

2012-02-28

An exciting new era in flavour physics has just begun with the start of the Large Hadron Collider (LHC). The LHCb (where b stands for beauty) experiment, designed specifically to search for new phenomena in quantum loop processes and to provide a deeper understanding of matter-antimatter asymmetries at the most fundamental level, is producing many new and exciting results. It gives me great pleasure to describe a selected few of the results here-in particular, the search for rare B(0)(s)-->μ+ μ- decays and the measurement of the B(0)(s) charge-conjugation parity-violating phase, both of which offer high potential for the discovery of new physics at and beyond the LHC energy frontier in the very near future.

Turning the LHC ring into a new physics search machine

NASA Astrophysics Data System (ADS)

Orava, Risto

2017-03-01

The LHC Collider Ring is proposed to be turned into an ultimate automatic search engine for new physics in four consecutive phases: (1) Searches for heavy particles produced in Central Exclusive Process (CEP): pp → p + X + p based on the existing Beam Loss Monitoring (BLM) system of the LHC; (2) Feasibility study of using the LHC Ring as a gravitation wave antenna; (3) Extensions to the current BLM system to facilitate precise registration of the selected CEP proton exit points from the LHC beam vacuum chamber; (4) Integration of the BLM based event tagging system together with the trigger/data acquisition systems of the LHC experiments to facilitate an on-line automatic search machine for the physics of tomorrow.

Radiation Physics for Space and High Altitude Air Travel

NASA Technical Reports Server (NTRS)

Cucinotta, F. A.; Wilson, J. W.; Goldhagen, P.; Saganti, P.; Shavers, M. R.; McKay, Gordon A. (Technical Monitor)

2000-01-01

Galactic cosmic rays (GCR) are of extra-solar origin consisting of high-energy hydrogen, helium, and heavy ions. The GCR are modified by physical processes as they traverse through the solar system, spacecraft shielding, atmospheres, and tissues producing copious amounts of secondary radiation including fragmentation products, neutrons, mesons, and muons. We discuss physical models and measurements relevant for estimating biological risks in space and high-altitude air travel. Ambient and internal spacecraft computational models for the International Space Station and a Mars mission are discussed. Risk assessment is traditionally based on linear addition of components. We discuss alternative models that include stochastic treatments of columnar damage by heavy ion tracks and multi-cellular damage following nuclear fragmentation in tissue.

The Imaging X-ray Polarimetry Explorer (IXPE)

NASA Astrophysics Data System (ADS)

Weisskopf, Martin C.; Ramsey, Brian; O'Dell, Stephen; Tennant, Allyn; Elsner, Ronald; Soffitta, Paolo; Bellazzini, Ronaldo; Costa, Enrico; Kolodziejczak, Jeffrey; Kaspi, Victoria; Muleri, Fabio; Marshall, Herman; Matt, Giorgio; Romani, Roger

2016-07-01

The Imaging X-ray Polarimetry Explorer (IXPE) expands observation space by simultaneously adding polarization measurements to the array of source properties currently measured (energy, time, and location). IXPE will thus open new dimensions for understanding how X-ray emission is produced in astrophysical objects, especially systems under extreme physical conditions—such as neutron stars and black holes. Polarization singularly probes physical anisotropies—ordered magnetic fields, aspheric matter distributions, or general relativistic coupling to black-hole spin—that are not otherwise measurable. Hence, IXPE complements all other investigations in high-energy astrophysics by adding important and relatively unexplored information to the parameter space for studying cosmic X-ray sources and processes, as well as for using extreme astrophysical environments as laboratories for fundamental physics.

Information Security Program Regulation

DTIC Science & Technology

1986-06-01

above. When an alarmed area is used for the storage of Top Secret material, the physical barrier must be adequate to prevent (a) surreptitious removal ...IV-9 4-304 Removable ADP and Word Processing Storage Media ---------- IV-10 4-305 Documents Produced by ADP Equipment...with a removal or cancellation of the classification designation. 1-315 Declassification Event An event that eliminates the need for continued

The Role of Concurrent Chemical and Physical Processes in Determining the Maximum Use Temperature of Thermosetting Polymers for Aerospace Applications

DTIC Science & Technology

2011-04-04

ore purchased f rom Lonz a, AG and used a s-received. Copper(I I) acetoacetonate from R OC/RIC and nony lphenol (Technical Grade) fro m Aldrich...were combined to produce a liquid catalyst. Sample Preparation. Catalyst batc hes were prepared by blending 30 weight parts nony lphenol with

High Fidelity Modeling of Field Reversed Configuration (FRC) Thrusters

DTIC Science & Technology

2017-04-22

signatures which can be used for direct, non -invasive, comparison with experimental diagnostics can be produced. This research will be directly... experimental campaign is critical to developing general design philosophies for low-power plasmoid formation, the complexity of non -linear plasma processes...advanced space propulsion. The work consists of numerical method development, physical model development, and systematic studies of the non -linear

[Dietary supplements from ground fish meat with DNA for treatment and prophylaxis].

PubMed

Boiarkina, L G; Kas'ianenko, Iu I; Epshteĭn, L M; Iakush, E V

1998-01-01

It has been developed a receipt of a new treatment-and-prophylactic products based on fish farce with treatment-and-prophylactic additive--DNA. It is recommended to be produced. As biological active additive keeps its initial pharmacological characteristics under technological processing this product is recommended for rendering general effect and increasing of physical and mental activity of organism.

Laboratory space physics: Investigating the physics of space plasmas in the laboratory

NASA Astrophysics Data System (ADS)

Howes, Gregory G.

2018-05-01

Laboratory experiments provide a valuable complement to explore the fundamental physics of space plasmas without the limitations inherent to spacecraft measurements. Specifically, experiments overcome the restriction that spacecraft measurements are made at only one (or a few) points in space, enable greater control of the plasma conditions and applied perturbations, can be reproducible, and are orders of magnitude less expensive than launching spacecraft. Here, I highlight key open questions about the physics of space plasmas and identify the aspects of these problems that can potentially be tackled in laboratory experiments. Several past successes in laboratory space physics provide concrete examples of how complementary experiments can contribute to our understanding of physical processes at play in the solar corona, solar wind, planetary magnetospheres, and the outer boundary of the heliosphere. I present developments on the horizon of laboratory space physics, identifying velocity space as a key new frontier, highlighting new and enhanced experimental facilities, and showcasing anticipated developments to produce improved diagnostics and innovative analysis methods. A strategy for future laboratory space physics investigations will be outlined, with explicit connections to specific fundamental plasma phenomena of interest.

The Capabilities of Chaos and Complexity

PubMed Central

Abel, David L.

2009-01-01

To what degree could chaos and complexity have organized a Peptide or RNA World of crude yet necessarily integrated protometabolism? How far could such protolife evolve in the absence of a heritable linear digital symbol system that could mutate, instruct, regulate, optimize and maintain metabolic homeostasis? To address these questions, chaos, complexity, self-ordered states, and organization must all be carefully defined and distinguished. In addition their cause-and-effect relationships and mechanisms of action must be delineated. Are there any formal (non physical, abstract, conceptual, algorithmic) components to chaos, complexity, self-ordering and organization, or are they entirely physicodynamic (physical, mass/energy interaction alone)? Chaos and complexity can produce some fascinating self-ordered phenomena. But can spontaneous chaos and complexity steer events and processes toward pragmatic benefit, select function over non function, optimize algorithms, integrate circuits, produce computational halting, organize processes into formal systems, control and regulate existing systems toward greater efficiency? The question is pursued of whether there might be some yet-to-be discovered new law of biology that will elucidate the derivation of prescriptive information and control. “System” will be rigorously defined. Can a low-informational rapid succession of Prigogine’s dissipative structures self-order into bona fide organization? PMID:19333445

A biotechnology perspective of fungal proteases.

PubMed

de Souza, Paula Monteiro; Bittencourt, Mona Lisa de Assis; Caprara, Carolina Canielles; de Freitas, Marcela; de Almeida, Renata Paula Coppini; Silveira, Dâmaris; Fonseca, Yris Maria; Ferreira Filho, Edivaldo Ximenes; Pessoa Junior, Adalberto; Magalhães, Pérola Oliveira

2015-06-01

Proteases hydrolyze the peptide bonds of proteins into peptides and amino acids, being found in all living organisms, and are essential for cell growth and differentiation. Proteolytic enzymes have potential application in a wide number of industrial processes such as food, laundry detergent and pharmaceutical. Proteases from microbial sources have dominated applications in industrial sectors. Fungal proteases are used for hydrolyzing protein and other components of soy beans and wheat in soy sauce production. Proteases can be produced in large quantities in a short time by established methods of fermentation. The parameters such as variation in C/N ratio, presence of some sugars, besides several other physical factors are important in the development of fermentation process. Proteases of fungal origin can be produced cost effectively, have an advantage faster production, the ease with which the enzymes can be modified and mycelium can be easily removed by filtration. The production of proteases has been carried out using submerged fermentation, but conditions in solid state fermentation lead to several potential advantages for the production of fungal enzymes. This review focuses on the production of fungal proteases, their distribution, structural-functional aspects, physical and chemical parameters, and the use of these enzymes in industrial applications.

Obesity: a chronic relapsing progressive disease process. A position statement of the World Obesity Federation.

PubMed

Bray, G A; Kim, K K; Wilding, J P H

2017-07-01

This paper considers the argument for obesity as a chronic relapsing disease process. Obesity is viewed from an epidemiological model, with an agent affecting the host and producing disease. Food is the primary agent, particularly foods that are high in energy density such as fat, or in sugar-sweetened beverages. An abundance of food, low physical activity and several other environmental factors interact with the genetic susceptibility of the host to produce positive energy balance. The majority of this excess energy is stored as fat in enlarged, and often more numerous fat cells, but some lipid may infiltrate other organs such as the liver (ectopic fat). The enlarged fat cells and ectopic fat produce and secrete a variety of metabolic, hormonal and inflammatory products that produce damage in organs such as the arteries, heart, liver, muscle and pancreas. The magnitude of the obesity and its adverse effects in individuals may relate to the virulence or toxicity of the environment and its interaction with the host. Thus, obesity fits the epidemiological model of a disease process except that the toxic or pathological agent is food rather than a microbe. Reversing obesity will prevent most of its detrimental effects. © 2017 World Obesity Federation.

Resonant Production of Sterile Neutrinos in the Early Universe

NASA Astrophysics Data System (ADS)

Gilbert, Lauren; Grohs, Evan; Fuller, George M.

2016-06-01

This study examines the cosmological impacts of a light resonantly produced sterile neutrino in the early universe. Such a neutrino could be produced through lepton number-driven Mikheyev-Smirnov-Wolfenstein (MSW) conversion of active neutrinos around big bang nucleosynthesis (BBN), resulting in a non-thermal spectrum of both sterile and electron neutrinos. During BBN, the neutron-proton ratio depends sensitively on the electron neutrino flux. If electron neutrinos are being converted to sterile neutrinos, this makes the n/p ratio a probe of possible new physics. We use observations of primordial Yp and D/H to place limits on this process.

Detection of structural changes and mechanical properties of light alloys after severe plastic deformation

NASA Astrophysics Data System (ADS)

Krasnoveikin, V. A.; Kozulin, A. A.; Skripnyak, V. A.

2017-11-01

Severe plastic deformation by equal channel angular pressing has been performed to produce light aluminum and magnesium alloy billets with ultrafine-grained structure. The physical and mechanical properties of the processed alloys are examined by studying their microstructure, measuring microhardness, yield strength, and uniaxial tensile strength. A nondestructive testing technique using three-dimensional X-ray tomography is proposed for detecting internal structural defects and monitoring damage formation in the structure of alloys subjected to severe plastic deformation. The investigation results prove the efficiency of the chosen method and selected mode of producing ultrafine-grained light alloys.

Processing mechanics of alternate twist ply (ATP) yarn technology

NASA Astrophysics Data System (ADS)

Elkhamy, Donia Said

Ply yarns are important in many textile manufacturing processes and various applications. The primary process used for producing ply yarns is cabling. The speed of cabling is limited to about 35m/min. With the world's increasing demands of ply yarn supply, cabling is incompatible with today's demand activated manufacturing strategies. The Alternate Twist Ply (ATP) yarn technology is a relatively new process for producing ply yarns with improved productivity and flexibility. This technology involves self plying of twisted singles yarn to produce ply yarn. The ATP process can run more than ten times faster than cabling. To implement the ATP process to produce ply yarns there are major quality issues; uniform Twist Profile and yarn Twist Efficiency. The goal of this thesis is to improve these issues through process modeling based on understanding the physics and processing mechanics of the ATP yarn system. In our study we determine the main parameters that control the yarn twist profile. Process modeling of the yarn twist across different process zones was done. A computational model was designed to predict the process parameters required to achieve a square wave twist profile. Twist efficiency, a measure of yarn torsional stability and bulk, is determined by the ratio of ply yarn twist to singles yarn twist. Response Surface Methodology was used to develop the processing window that can reproduce ATP yarns with high twist efficiency. Equilibrium conditions of tensions and torques acting on the yarns at the self ply point were analyzed and determined the pathway for achieving higher twist efficiency. Mechanistic modeling relating equilibrium conditions to the twist efficiency was developed. A static tester was designed to zoom into the self ply zone of the ATP yarn. A computer controlled, prototypic ATP machine was constructed and confirmed the mechanistic model results. Optimum parameters achieving maximum twist efficiency were determined in this study. The successful results of this work have led to the filing of a US patent disclosing the method for producing ATP yarns with high yarn twist efficiency using a high convergence angle at the self ply point together with applying ply torque.

Comments on "The Sensitivity Study of Radiative-Convective Equilibrium in the Tropics with a Convective Resolving Model"

NASA Technical Reports Server (NTRS)

Tao, W.-K.; Shie, C.-L.; Simpson, J.

2000-01-01

In general, there are two broad scientific objectives when using cloud resolving models (CRMs or cloud ensemble models-CEMs) to study tropical convection. The first one is to use them as a physics resolving models to understand the dynamic and microphysical processes associated with the tropical water and energy cycles and their role in the climate system. The second approach is to use the CRMs to improve the representation of moist processes and their interaction with radiation in large-scale models. In order to improve the credibility of the CRMs and achieve the above goals, CRMs using identical initial conditions and large-scale influences need to produce very similar results. Two CRMs produced different statistical equilibrium (SE) states even though both used the same initial thermodynamic and wind conditions. Sensitivity tests to identify the major physical processes that determine the SE states for the different CRM simulations were performed. Their results indicated that atmospheric horizontal wind is treated quite differently in these two CRMs. The model that had stronger surface winds and consequently larger latent and sensible heat fluxes from the ocean produced a warmer and more humid modeled thermodynamic SE state. In addition, the domain mean thermodynamic state is more unstable for those experiments that produced a warmer and more humid SE state. Their simulated wet (warm and humid) SE states are thermally more stable in the lower troposphere (from the surface to 4-5 km in altitude). The large-scale horizontal advective effects on temperature and water vapor mixing ratio are needed when using CRMs to perform long-term integrations to study convective feedback under specified large-scale environments. In addition, it is suggested that the dry and cold SE state simulated was caused by enhanced precipitation but not enough surface evaporation. We find some problems with the interpretation of these three phenomena.

Numerical simulations of an advection fog event over Shanghai Pudong International Airport with the WRF model

NASA Astrophysics Data System (ADS)

Lin, Caiyan; Zhang, Zhongfeng; Pu, Zhaoxia; Wang, Fengyun

2017-10-01

A series of numerical simulations is conducted to understand the formation, evolution, and dissipation of an advection fog event over Shanghai Pudong International Airport (ZSPD) with the Weather Research and Forecasting (WRF) model. Using the current operational settings at the Meteorological Center of East China Air Traffic Management Bureau, the WRF model successfully predicts the fog event at ZSPD. Additional numerical experiments are performed to examine the physical processes associated with the fog event. The results indicate that prediction of this particular fog event is sensitive to microphysical schemes for the time of fog dissipation but not for the time of fog onset. The simulated timing of the arrival and dissipation of the fog, as well as the cloud distribution, is substantially sensitive to the planetary boundary layer and radiation (both longwave and shortwave) processes. Moreover, varying forecast lead times also produces different simulation results for the fog event regarding its onset and duration, suggesting a trade-off between more accurate initial conditions and a proper forecast lead time that allows model physical processes to spin up adequately during the fog simulation. The overall outcomes from this study imply that the complexity of physical processes and their interactions within the WRF model during fog evolution and dissipation is a key area of future research.

PEGylated Biodegradable Polyesters for PGSS Microparticles Formulation: Processability, Physical and Release Properties.

PubMed

Perinelli, D R; Cespi, M; Bonacucina, G; Naylor, A; Whitaker, M; Lam, J K W; Howdle, S M; Casettari, L; Palmieri, G F

2016-01-01

Particles from Gas Saturated Solution (PGSS) is an emergent method that employs supercritical carbon dioxide (scCO2) to produce microparticles. It is suitable for encapsulating biologically active compounds including therapeutic peptides and proteins. Poly(lactide acid) (PLA) and/or poly(lactic-coglycolic acid) (PLGA) are the most commonly used materials in PGSS, due to their good processability in scCO2. Previous studies demonstrated that the properties of the microparticles can be modulated by adding polyethylene glycol (PEG) or tri-block PEGylated copolymers. In the present work, the effect of the addition of biodegradable PEGylated di-block copolymers on the physical properties and drug release performance of microparticles prepared by PGSS technique was evaluated. mPEG5kDa-P(L)LA and mPEG5kDa-P(L)LGA with similar molecular weights were synthesized and their behaviour, when exposed to supercritical CO2, was investigated. Different microparticle formulations, composed of a high (81%) or low (9%) percentage of the synthesized copolymers were prepared and compared in terms of particle size distribution, morphology, yield and protein release. Drug release studies were performed using bovine serum albumin (BSA) as a model protein. PEGylated copolymers showed good processability in PGSS without significant changes to the physical properties of the microparticles. However, the addition of PEG exerted a modulating effect on the microparticle drug dissolution behaviour, increasing the rate of BSA release as a function of its content in the formulation. This study demonstrated the feasibility of producing microparticles by using PEGylated di-block copolymers through a PGSS technique at mild operating conditions (low operating pressure and temperature).

Space Weather Effects Produced by the Ring Current Particles

NASA Astrophysics Data System (ADS)

Ganushkina, Natalia; Jaynes, Allison; Liemohn, Michael

2017-11-01

One of the definitions of space weather describes it as the time-varying space environment that may be hazardous to technological systems in space and/or on the ground and/or endanger human health or life. The ring current has its contributions to space weather effects, both in terms of particles, ions and electrons, which constitute it, and magnetic and electric fields produced and modified by it at the ground and in space. We address the main aspects of the space weather effects from the ring current starting with brief review of ring current discovery and physical processes and the Dst-index and predictions of the ring current and storm occurrence based on it. Special attention is paid to the effects on satellites produced by the ring current electrons. The ring current is responsible for several processes in the other inner magnetosphere populations, such as the plasmasphere and radiation belts which is also described. Finally, we discuss the ring current influence on the ionosphere and the generation of geomagnetically induced currents (GIC).

Modeling the Colorado Front Range Flood of 2013 with Coupled WRF and WRF-Hydro System

NASA Astrophysics Data System (ADS)

Unal, E.; Ramirez, J. A.

2015-12-01

Abstract. Flash floods are one of the most damaging natural disasters producing large socio-economic losses. Projected impacts of climate change include increases in the magnitude and the frequency of flash floods all around the world. Therefore, it is important to understand the physical processes of flash flooding to enhance our capacity for prediction, prevention, risk management, and recovery. However, understanding these processes is ambitious because of small spatial scale and sudden nature of flash floods, interactions with complex topography and land use, difficulty in defining initial soil moisture conditions, non-linearity of catchment response, and high space-time variability of storm characteristics. Thus, detailed regional case studies are needed, especially with respect to the interactions between the land surface and the atmosphere. One such flash flood event occurred recently in the Front Range of the Rocky Mountains of Colorado during September 9-15, 2013 causing 10 fatalities and $3B cost in damages. An unexpected persistent and moist weather pattern located over the mountains and produced seven-day extreme rainfall fed by moisture input from the Gulf of Mexico. We used a coupled WRF-WRF-Hydro modeling system to simulate this event for better understanding of the physical process and of the sensitivity of the hydrologic response to storm characteristics, initial soil moisture conditions, and watershed characteristics.

Prediction of natural disasters basing of chrono-and-information field characters

NASA Astrophysics Data System (ADS)

Sapunov, Valentin

2013-04-01

Living organisms are able to predict some future events particular catastrophic incidents. This is adaptive characters producing by evolution. The more energy produces incident the more possibility to predict one. Wild animals escaped natural hazards including tsunami (e.g. extremal tsunami in Asia December 2004). Living animals are able to predict strong phenomena of obscure nature. For example majority of animals escaped Tungus catastrophe taking place in Siberia at 1908. Wild animals are able to predict nuclear weapon experiences. The obscure characters are not typical for human, but they are fixed under probability 15%. Such were summarized by L.Vasiliev (1961). Effective theory describing such a characters is absent till now. N.Kozyrev (1991) suggested existence of unknown physical field (but gravitation and electro magnetic). The field was named "time" or "chrono". Some characters of the field appeared to be object of physical experiment. Kozyrev suggested specific role of the field for function of living organisms. Transition of biological information throw space (telepathy) and time (proscopy) may be based on characters of such a field. Hence physical chrono-and-information field is under consideration. Animals are more familiar with such a field than human. Evolutionary process experienced with possibility of extremal development of contact with such a field using highest primates. This mode of evolution appeared to stay obscure producing probable species "Wildman" (Bigfoot). Specific adaptive fitches suggest impossibility to study of such a species by usual ecological approaches. The perspective way for study of mysterious phenomena of physic is researches of this field characters.

Conveyor belt biomantles: Centripetal bioturbation coupled with erosional downwasting -- an explanatory model

NASA Astrophysics Data System (ADS)

Johnson, D. L.; Johnson, D. N.

2012-12-01

Science advances on the strength of clarifying and unifying concepts, models, and methodologies that enhance and expand our explanatory paradigms. If valid, such structures allow us to accurately understand and appreciate how the world works. To aid in this task, new term-concepts must sometimes be coined and formalized. To understand certain ubiquitously occurring -- though as yet un-conceptualized -- surface processes that operate non-stop, and assessing their efficacies, is a desirable goal in landscape evolution studies. All near-surface processes are, of course, biological, chemical, and or physical in nature, and many if not most operate in combination. But of this triumvirate, biological processes, both biochemical and biomechanical (bioturbations), are perhaps least understood. Combinations of ubiquitously and semi-continuously occurring poorly understood processes that are both obscure and yet obvious have collectively produced Earth's biomantle. The biomantle occupies the uppermost Pedosphere, is a planet-wide layer, and unique to Earth. It thus functions as the biogenically habitable interface between the Atmosphere, Biosphere, Hydrosphere, and Lithosphere. The biomantle is defined as the organic-bearing bioturbated upper part of soil, including the topsoil, and of subaqueous substrates (lake, stream, ocean floor sediments) where most biota live, operate, move, wriggle, rest, sleep, estivate, seek food, eat, compete, fight, hide, reproduce, die, and assimilate. Its position and function in the uppermost soil layer of the Critical Zone must modulate and mediate much or most of what takes place above and below in ways yet to be established. In an attempt to increase understanding of this complicated biodynamic pedomembrane, and to identify the main processes that produce it, we present an iterative process model that pits ongoing cyclic bioturbation driven constructional processes against ongoing cyclic physically driven destructional processes. More specifically, and in summary, we present a model that displays how semi-continuous biomechanical and centripetally driven constructional soil-sediment biotransfers to raised animal-produced point centers are concomitantly leveled by physical-erosional centrifugally driven, lateral-radial downwasting processes. The model is analogous to a cyclical conveyor belt system of soil-sediment biotransfers to, then erosionally away, from innumerably raised point centers, the "activity centers" of burrowing animals. Career-spanning fieldwork across many tropical, subtropical, and mid-latitude environments strongly support the overall validity of the model. Apart from microbes, animals represent the most diverse organismic group on the planet, with plants and fungi distant seconds. Moreover, many if not most spend at least part of their existence living on and/or in soil and sediment, which includes both the subaerial and subaqueous realms of Earth (that is, all of it, except extreme polar areas). Animals bioturbate, vertically and laterally, and likely have done so since pre-Cambrian time. The fundamental conveyor belt process, where ongoing centripetal bioturbations are coupled with ongoing erosional wasting and spreading, joined by subsidiary processes, drives biomantle formation.

Current Topics in Gamma-Ray Astrophysics

PubMed Central

Mathews, Grant J.; Maronetti, P.; Salmonson, Jay; Wilson, J. R.

2000-01-01

This paper reports on recent progress toward unraveling the origin of gamma-ray bursts. It is concluded that neutron-star binaries are one of the few remaining candidates. A model is proposed based upon general relativistic hydrodynamic studies which indicate a new physical process by which to power a gamma-ray burst. Relativistically driven compression, heating, and collapse of the individual neutron stars can occur many seconds before inspiral and merger. This compression may produce a neutrino burst of ∼1053 ergs lasting several seconds. The associated thermal neutrino emission produces an e+–e − pair plasma by vv¯ annihilation. We show first results of a simulated burst which produces ∼1051 erg in γ rays of the correct spectral and temporal properties. PMID:27551592

Current Topics in Gamma-Ray Astrophysics.

PubMed

Mathews, G J; Maronetti, P; Salmonson, J; Wilson, J R

2000-01-01

This paper reports on recent progress toward unraveling the origin of gamma-ray bursts. It is concluded that neutron-star binaries are one of the few remaining candidates. A model is proposed based upon general relativistic hydrodynamic studies which indicate a new physical process by which to power a gamma-ray burst. Relativistically driven compression, heating, and collapse of the individual neutron stars can occur many seconds before inspiral and merger. This compression may produce a neutrino burst of ∼10(53) ergs lasting several seconds. The associated thermal neutrino emission produces an e (+)-e (-) pair plasma by [Formula: see text] annihilation. We show first results of a simulated burst which produces ∼10(51) erg in γ rays of the correct spectral and temporal properties.

Plasma Spray-Physical Vapor Deposition (PS-PVD) of Ceramics for Protective Coatings

NASA Technical Reports Server (NTRS)

Harder, Bryan J.; Zhu, Dongming

2011-01-01

In order to generate advanced multilayer thermal and environmental protection systems, a new deposition process is needed to bridge the gap between conventional plasma spray, which produces relatively thick coatings on the order of 125-250 microns, and conventional vapor phase processes such as electron beam physical vapor deposition (EB-PVD) which are limited by relatively slow deposition rates, high investment costs, and coating material vapor pressure requirements. The use of Plasma Spray - Physical Vapor Deposition (PS-PVD) processing fills this gap and allows thin (< 10 microns) single layers to be deposited and multilayer coatings of less than 100 microns to be generated with the flexibility to tailor microstructures by changing processing conditions. Coatings of yttria-stabilized zirconia (YSZ) were applied to NiCrAlY bond coated superalloy substrates using the PS-PVD coater at NASA Glenn Research Center. A design-of-experiments was used to examine the effects of process variables (Ar/He plasma gas ratio, the total plasma gas flow, and the torch current) on chamber pressure and torch power. Coating thickness, phase and microstructure were evaluated for each set of deposition conditions. Low chamber pressures and high power were shown to increase coating thickness and create columnar-like structures. Likewise, high chamber pressures and low power had lower growth rates, but resulted in flatter, more homogeneous layers

Simulating industrial plasma reactors - A fresh perspective

NASA Astrophysics Data System (ADS)

Mohr, Sebastian; Rahimi, Sara; Tennyson, Jonathan; Ansell, Oliver; Patel, Jash

2016-09-01

A key goal of the presented research project PowerBase is to produce new integration schemes which enable the manufacturability of 3D integrated power smart systems with high precision TSV etched features. The necessary high aspect ratio etch is performed via the BOSCH process. Investigations in industrial research are often use trial and improvement experimental methods. Simulations provide an alternative way to study the influence of external parameters on the final product, whilst also giving insights into the physical processes. This presentation investigates the process of simulating an industrial ICP reactor used over high power (up to 2x5 kW) and pressure (up to 200 mTorr) ranges, analysing the specific procedures to achieve a compromise between physical correctness and computational speed, while testing commonly made assumptions. This includes, for example, the effect of different physical models and the inclusion of different gas phase and surface reactions with the aim of accurately predicting the dependence of surface rates and profiles on external parameters in SF6 and C4F8 discharges. This project has received funding from the Electronic Component Systems for European Leadership Joint Undertaking under Grant Agreement No. 662133 PowerBase.

Low Altitude Solar Magnetic Reconnection, Type III Solar Radio Bursts, and X-ray Emissions.

PubMed

Cairns, I H; Lobzin, V V; Donea, A; Tingay, S J; McCauley, P I; Oberoi, D; Duffin, R T; Reiner, M J; Hurley-Walker, N; Kudryavtseva, N A; Melrose, D B; Harding, J C; Bernardi, G; Bowman, J D; Cappallo, R J; Corey, B E; Deshpande, A; Emrich, D; Goeke, R; Hazelton, B J; Johnston-Hollitt, M; Kaplan, D L; Kasper, J C; Kratzenberg, E; Lonsdale, C J; Lynch, M J; McWhirter, S R; Mitchell, D A; Morales, M F; Morgan, E; Ord, S M; Prabu, T; Roshi, A; Shankar, N Udaya; Srivani, K S; Subrahmanyan, R; Wayth, R B; Waterson, M; Webster, R L; Whitney, A R; Williams, A; Williams, C L

2018-01-26

Type III solar radio bursts are the Sun's most intense and frequent nonthermal radio emissions. They involve two critical problems in astrophysics, plasma physics, and space physics: how collective processes produce nonthermal radiation and how magnetic reconnection occurs and changes magnetic energy into kinetic energy. Here magnetic reconnection events are identified definitively in Solar Dynamics Observatory UV-EUV data, with strong upward and downward pairs of jets, current sheets, and cusp-like geometries on top of time-varying magnetic loops, and strong outflows along pairs of open magnetic field lines. Type III bursts imaged by the Murchison Widefield Array and detected by the Learmonth radiospectrograph and STEREO B spacecraft are demonstrated to be in very good temporal and spatial coincidence with specific reconnection events and with bursts of X-rays detected by the RHESSI spacecraft. The reconnection sites are low, near heights of 5-10 Mm. These images and event timings provide the long-desired direct evidence that semi-relativistic electrons energized in magnetic reconnection regions produce type III radio bursts. Not all the observed reconnection events produce X-ray events or coronal or interplanetary type III bursts; thus different special conditions exist for electrons leaving reconnection regions to produce observable radio, EUV, UV, and X-ray bursts.

Microbiological Safety of Animal Wastes Processed by Physical Heat Treatment: An Alternative To Eliminate Human Pathogens in Biological Soil Amendments as Recommended by the Food Safety Modernization Act.

PubMed

Chen, Zhao; Jiang, Xiuping

2017-03-01

Animal wastes have high nutritional value as biological soil amendments of animal origin for plant cultivation in sustainable agriculture; however, they can be sources of some human pathogens. Although composting is an effective way to reduce pathogen levels in animal wastes, pathogens may still survive under certain conditions and persist in the composted products, which potentially could lead to fresh produce contamination. According to the U.S. Food and Drug Administration Food Safety Modernization Act, alternative treatments are recommended for reducing or eliminating human pathogens in raw animal manure. Physical heat treatments can be considered an effective method to inactivate pathogens in animal wastes. However, microbial inactivation in animal wastes can be affected by many factors, such as composition of animal wastes, type and physiological stage of the tested microorganism, and heat source. Following some current processing guidelines for physical heat treatments may not be adequate for completely eliminating pathogens from animal wastes. Therefore, this article primarily reviews the microbiological safety and economic value of physically heat-treated animal wastes as biological soil amendments.

The effectiveness of physics learning material based on South Kalimantan local wisdom

NASA Astrophysics Data System (ADS)

Hartini, Sri; Misbah, Helda, Dewantara, Dewi

2017-08-01

The local wisdom is essential element incorporated into learning process. However, there are no learning materials in Physics learning process which contain South Kalimantan local wisdom. Therefore, it is necessary to develop a Physics learning material based on South Kalimantan local wisdom. The objective of this research is to produce products in the form of learning material based on South Kalimantan local wisdom that is feasible and effective based on the validity, practicality, effectiveness of learning material and achievement of waja sampai kaputing (wasaka) character. This research is a research and development which refers to the ADDIE model. Data were obtained through the validation sheet of learning material, questionnaire, the test of learning outcomes and the sheet of character assesment. The research results showed that (1) the validity category of the learning material was very valid, (2) the practicality category of the learning material was very practical, (3) the effectiveness category of thelearning material was very effective, and (4) the achivement of wasaka characters was very good. In conclusion, the Physics learning materials based on South Kalimantan local wisdom are feasible and effective to be used in learning activities.

Women living with a spinal cord injury: perceptions about their changed bodies.

PubMed

Chau, Lisa; Hegedus, Lenke; Praamsma, Monate; Smith, Katey; Tsukada, Michiko; Yoshida, Karen; Renwick, Rebecca

2008-02-01

In this article we illuminate the narratives of women living with a spinal cord injury (SCI) with regard to (a) learning how to live with a changed body and (b) exploring the factors that influence how they feel toward their new bodies. An SCI produces immediate physical impairments resulting in a changed body, which can then have physical, emotional, and social consequences to these women. Through its focus on enhancing the body, physical therapy can help to promote a positive view of the self within the changed body. Our analysis of these women's experiences resulted in a fluid, three-phase framework of learning to live with a changed body that generally moves from (a) discomfort, to (b) moving toward comfort, to (c) comfort. Physical therapy can potentially influence the process of women's gaining comfort with their changed bodies following an SCI. The framework provides a basis for future research on adaptation following SCI.

Development of website for studying modern physics

NASA Astrophysics Data System (ADS)

Saehana, S.; Wahyono, U.; Darmadi, I. W.; Kendek, Y.; Widyawati, W.

2018-03-01

The purpose of this study is to produce a website in modern physics courses in order to increase student interest in physics learning. To determine the feasibility level of learning media then feasibility test to the product. The feasibility test carried out on the product is divided into three parts: material feasibility test, media feasibility test, and student response test. Based on the results of the test conducted the material obtained an average score of 3.72 and categorized very well. The result of media test that was obtained got the average score of 3.25 and categorized well. The result of the analysis of student's response to the twenty students of class A (fifth semester) of physics education program FKIP UniversitasTadulako obtained an average score of 3.16 with the good category. The results showed that the website developed can be used as one of the learning media that can support the learning process of students.

Effect of humic acids on intestinal viscosity, leaky gut and ammonia excretion in a 24 h feed restriction model to induce intestinal permeability in broiler chickens

USDA-ARS?s Scientific Manuscript database

Humic acids (HA) are produced by biodegradation of organic matter that involves physical, chemical and microbiological processes, hence, HA are a complex mixture of many different acids containing carboxyl and phenolate groups. The purpose of this study was to evaluate the effect of HA on intestina...

An Investigation of the Height of Embossed Braille Dots for Labels on Pharmaceutical Products

ERIC Educational Resources Information Center

Douglas, Graeme; Weston, Annette; Whittaker, Jennifer; Wilkins, Sarah Morley; Robinson, Duncan

2009-01-01

European legislation requires new pharmaceutical packaging to include both the name and strength of the drug in braille on boxes and bottles. Much of the braille on medical packaging is currently produced by an embossing process on boxes. The height of the dots that can be achieved through these methods is less than 0.3 mm. The physical dimensions…

Abstracts of the International Conference (INFOS 83) on Insulating Films on Semiconductors Held at the University of Technology. Eindhoven (The Netherlands) on 11-13 April 1983.

DTIC Science & Technology

1983-04-13

progressed at the same pace. Initially the analogy with conventional well-known ion sensors, such as the glass membrane electrode, led to the...chemical and physical treatments. The standard etching processing using bromine in methanol can deplete cations and produce a surface layer of TeO2 .(l

Bioprocess for treating coproduced oily sands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Munnecke, D.M.; Ireland, J.

1996-12-31

The production of oil from certain oil fields creates significant amounts of oily sand which in many regulatory jurisdictions is regulated as a hazardous material, thus disposal costs can be significant. Environmental BioTechnologies, Inc. (San Carlos, CA) has developed a physical/biological treatment process that is able to economically treat these coproduced sands and produce a product that contains less than 2,000 ppm total petroleum hydrocarbons.

Radiofrequency and microwave radiation in the microelectronics industry.

PubMed

Cohen, R

1986-01-01

The microscopic precision required to produce minute integrated circuits is dependent on several processes utilizing radiofrequency and microwave radiation. This article provides a review of radiofrequency and microwave exposures in microelectronics and of the physical and biologic properties of these types of radiation; summarizes the existing, relevant medical literature; and provides the clinician with guidelines for diagnosis and treatment of excessive exposures to microwave and radiofrequency radiation.

A Reappraisal of the Mechanism of Pion Exchange and Its Implications for the Teaching of Particle Physics

ERIC Educational Resources Information Center

Dunne, Peter

2002-01-01

The origins of the pion exchange model of nuclear forces are described and the exchange process is reinterpreted in the light of current views on the quark-gluon structure of nucleons. It is suggested that the reinterpretation might provide a picture of cohesive nuclear forces that is more intellectually satisfying than that produced by the…

How online learning modules can improve the representational fluency and conceptual understanding of university physics students

NASA Astrophysics Data System (ADS)

Hill, M.; Sharma, M. D.; Johnston, H.

2015-07-01

The use of online learning resources as core components of university science courses is increasing. Learning resources range from summaries, videos, and simulations, to question banks. Our study set out to develop, implement, and evaluate research-based online learning resources in the form of pre-lecture online learning modules (OLMs). The aim of this paper is to share our experiences with those using, or considering implementing, online learning resources. Our first task was to identify student learning issues in physics to base the learning resources on. One issue with substantial research is conceptual understanding, the other with comparatively less research is scientific representations (graphs, words, equations, and diagrams). We developed learning resources on both these issues and measured their impact. We created weekly OLMs which were delivered to first year physics students at The University of Sydney prior to their first lecture of the week. Students were randomly allocated to either a concepts stream or a representations stream of online modules. The programme was first implemented in 2013 to trial module content, gain experience and process logistical matters and repeated in 2014 with approximately 400 students. Two validated surveys, the Force and Motion Concept Evaluation (FMCE) and the Representational Fluency Survey (RFS) were used as pre-tests and post-tests to measure learning gains while surveys and interviews provided further insights. While both streams of OLMs produced similar positive learning gains on the FMCE, the representations-focussed OLMs produced higher gains on the RFS. Conclusions were triangulated with student responses which indicated that they have recognized the benefit of the OLMs for their learning of physics. Our study shows that carefully designed online resources used as pre-instruction can make a difference in students’ conceptual understanding and representational fluency in physics, as well as make them more aware of their learning processes. In particular, the representations-focussed modules offer more advantages.

Physics students' approaches to learning and cognitive processes in solving physics problems

NASA Astrophysics Data System (ADS)

Bouchard, Josee

This study examined traditional instruction and problem-based learning (PBL) approaches to teaching and the extent to which they foster the development of desirable cognitive processes, including metacognition, critical thinking, physical intuition, and problem solving among undergraduate physics students. The study also examined students' approaches to learning and their perceived role as physics students. The research took place in the context of advanced courses of electromagnetism at a Canadian research university. The cognitive science, expertise, physics and science education, instructional psychology, and discourse processes literature provided the framework and background to conceptualize and structure this study. A within-stage mixed-model design was used and a number of instruments, including a survey, observation grids, and problem sets were developed specifically for this study. A special one-week long problem-based learning (PBL) intervention was also designed. Interviews with the instructors participating in the study provided complementary data. Findings include evidence that students in general engage in metacognitive processes in the organization of their personal study time. However, this potential, including the development of other cognitive processes, might not be stimulated as much as it could in the traditional lecture instructional context. The PBL approach was deemed as more empowering for the students. An unexpected finding came from the realisation that a simple exposure to a structured exercise of problem-solving (pre-test) was sufficient to produce superior planning and solving strategies on a second exposure (post-test) even for the students who had not been exposed to any special treatment. Maturation was ruled out as a potential threat to the validity of this finding. Another promising finding appears to be that the problem-based learning (PBL) intervention tends to foster the development of cognitive competencies, particularly physical intuition, even if it was only implemented for a short period of time. Other findings relate to the nature of the cognitive actions and activities that the students engage in when learning to solve electromagnetism problems in a PBL environment for the first time and the tutoring actions that guide students in this context.

Near perfect optics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goeke, R.; Farnsworth, A.V.; Neumann, C.C.

1996-06-01

This report discusses a novel fabrication process to produce nearly perfect optics. The process utilizes vacuum deposition techniques to optimally modify polished optical substrate surfaces. The surface figure, i.e. contour of a polished optical element, is improved by differentially filling in the low spots on the surface using flux from a physical vapor deposition source through an appropriate mask. The process is expected to enable the manufacture of diffraction-limited optical systems for the UV, extreme UV, and soft X-ray spectral regions, which would have great impact on photolithography and astronomy. This same technique may also reduce the fabrication cost ofmore » visible region optics with aspheric surfaces.« less

Nittrouer Receives 2013 Luna B. Leopold Young Scientist Award: Response

NASA Astrophysics Data System (ADS)

Nittrouer, Jeffrey A.

2014-09-01

I am grateful for receiving the Luna B. Leopold Award from the Earth and Planetary Surface Processes (EPSP) focus group at AGU. I am thankful to the mentors and colleagues who played important roles in shaping my science over the past 10 years. Significant credit goes to three people in particular: David Mohrig, Gary Parker, and Mead Allison. These gentlemen patiently developed and honed my skills for observing, modeling, and theorizing about the physical processes that produce fluvial-deltaic morphology and stratigraphy. It was an incredible opportunity to have worked with such a diverse set of thinkers, who regularly pushed me to consider and pursue new ideas, preventing too much comfort with the scientific status quo. Their mentoring fostered an independent and creative focus that produced the science for which this award has been generously given.

Tensile Properties Characterization of AlSi10Mg Parts Produced by Direct Metal Laser Sintering via Nested Effects Modeling.

PubMed

Palumbo, Biagio; Del Re, Francesco; Martorelli, Massimo; Lanzotti, Antonio; Corrado, Pasquale

2017-02-08

A statistical approach for the characterization of Additive Manufacturing (AM) processes is presented in this paper. Design of Experiments (DOE) and ANalysis of VAriance (ANOVA), both based on Nested Effects Modeling (NEM) technique, are adopted to assess the effect of different laser exposure strategies on physical and mechanical properties of AlSi10Mg parts produced by Direct Metal Laser Sintering (DMLS). Due to the wide industrial interest in AM technologies in many different fields, it is extremely important to ensure high parts performances and productivity. For this aim, the present paper focuses on the evaluation of tensile properties of specimens built with different laser exposure strategies. Two optimal laser parameters settings, in terms of both process quality (part performances) and productivity (part build rate), are identified.

Tensile Properties Characterization of AlSi10Mg Parts Produced by Direct Metal Laser Sintering via Nested Effects Modeling

PubMed Central

Palumbo, Biagio; Del Re, Francesco; Martorelli, Massimo; Lanzotti, Antonio; Corrado, Pasquale

2017-01-01

A statistical approach for the characterization of Additive Manufacturing (AM) processes is presented in this paper. Design of Experiments (DOE) and ANalysis of VAriance (ANOVA), both based on Nested Effects Modeling (NEM) technique, are adopted to assess the effect of different laser exposure strategies on physical and mechanical properties of AlSi10Mg parts produced by Direct Metal Laser Sintering (DMLS). Due to the wide industrial interest in AM technologies in many different fields, it is extremely important to ensure high parts performances and productivity. For this aim, the present paper focuses on the evaluation of tensile properties of specimens built with different laser exposure strategies. Two optimal laser parameters settings, in terms of both process quality (part performances) and productivity (part build rate), are identified. PMID:28772505

NASA Astrophysics Data System (ADS)

Lee, D.

1995-09-01

The JET KOTE coating process is a high-velocity oxyfuel process used to form coatings of high quality and density. Coatings can be produced from carbide-bearing composite, alloyed metallic, nonmetallic, intermetallic, or pure metal powders. The coatings are used for wear and/or corrosion resistance in the aircraft, chemical, oil and gas, and steel manufacturing industries, as well as in other demanding fields. Many applications, especially in the petrochemical field, require thick coatings. Coatings must be applied economically, without loss of integrity. Thickness limitations are thought to be due to coating stress, which results in coating cracks and/or delamination and ultimately in failure. This paper examines the effects of operating parameters and techniques on the physical properties of thick coatings produced from Stelcar JK117, a tungsten carbide/17 % Co composite powder. Special emphasis is placed on those parameters which are economically desirable to achieve high deposition rates.

Search strategy using LHC pileup interactions as a zero bias sample

NASA Astrophysics Data System (ADS)

Nachman, Benjamin; Rubbo, Francesco

2018-05-01

Due to a limited bandwidth and a large proton-proton interaction cross section relative to the rate of interesting physics processes, most events produced at the Large Hadron Collider (LHC) are discarded in real time. A sophisticated trigger system must quickly decide which events should be kept and is very efficient for a broad range of processes. However, there are many processes that cannot be accommodated by this trigger system. Furthermore, there may be models of physics beyond the standard model (BSM) constructed after data taking that could have been triggered, but no trigger was implemented at run time. Both of these cases can be covered by exploiting pileup interactions as an effective zero bias sample. At the end of high-luminosity LHC operations, this zero bias dataset will have accumulated about 1 fb-1 of data from which a bottom line cross section limit of O (1 ) fb can be set for BSM models already in the literature and those yet to come.

Resource Efficient Metal and Material Recycling

NASA Astrophysics Data System (ADS)

Reuter, Markus A.; van Schaik, Antoinette

Metals enable sustainability through their use and their recyclability. However, various factors can affect the Resource Efficiency of Metal Processing and Recycling. Some typical factors that enable Resource Efficiency include and arranged under the drivers of sustainability: Environment (Maximize Resource Efficiency — Energy, Recyclates, Materials, Water, Sludges, Emissions, Land); Economic Feasibility (BAT & Recycling Systems Simulation / Digitalization, Product vis-à-vis Material Centric Recycling); and Social — Licence to Operate (Legislation, consumer, policy, theft, manual labour.). In order to realize this primary production has to be linked systemically with typical actors in the recycling chain such as Original Equipment Manufacturers (OEMs), Recyclers & Collection, Physical separation specialists as well as process metallurgical operations that produce high value metals, compounds and products that recycle back to products. This is best done with deep knowledge of multi-physics, technology, product & system design, process control, market, life cycle management, policy, to name a few. The combination of these will be discussed as Design for Sustainability (DfS) and Design for Recycling (DfR) applications.

Study of the coupling between real gas effects and rarefied effects on hypersonic aerodynamics

NASA Astrophysics Data System (ADS)

Chen, Song; Hu, Yuan; Sun, Quanhua

2012-11-01

Hypersonic vehicles travel across the atmosphere at very high speed, and the surrounding gas experiences complicated physical and chemical processes. These processes produce real gas effects at high temperature and rarefied gas effects at high altitude where the two effects are coupled through molecular collisions. In this study, we aim to identify the individual real gas and rarefied gas effects by simulating hypersonic flow over a 2D cylinder, a sphere and a blunted cone using a continuum-based CFD approach and the direct simulation Monte Carlo method. It is found that physical processes such as vibrational excitation and chemical reaction will reduce significantly the shock stand-off distance and flow temperature for flows having small Knudsen number. The calculated skin friction and surface heat flux will decrease when the real gas effects are considered in simulations. The trend, however, gets weakened as the Knudsen number increases. It is concluded that the rarefied gas effects weaken the real gas effects on hypersonic flows.

Preliminary Breakdown: Physical Mechanisms and Potential for Energetic Emissions

NASA Astrophysics Data System (ADS)

Petersen, D.; Beasley, W. H.

2014-12-01

Observations and analysis of the preliminary breakdown phase of virgin negative cloud-to-ground (-CG) lightning strokes will be presented. Of primary interest are the physical processes responsible for the fast electric field "characteristic" pulses that are often observed during this phase. The pulse widths of characteristic pulses are shown to occur as a superposed bimodal distribution, with the short and long modes having characteristic timescales on the order of 1 microsecond and 10 microseconds, respectively. Analysis of these pulses is based on comparison with laboratory observations of long spark discharge processes and with recently acquired high-speed video observations of a single -CG event. It will be argued that the fast electric field bimodal distribution is the result of conventional discharge processes operating in an extensive strong ambient electric field environment. An important related topic will also be discussed, where it will be argued that preliminary breakdown discharges are capable of generating energetic electrons and may therefore seed relativistic electron avalanches that go on to produce pulsed energetic photon emissions.

Physics of the inner heliosphere: Mechanisms, models and observational signatures

NASA Technical Reports Server (NTRS)

Withbroe, George L.

1987-01-01

Selected problems concerned with the important physical processes that occur in the corona and solar wind acceleration region, particularly time dependent phenomena were studied. Both the physics of the phenomena and the resultant effects on observational signatures, particularly spectroscopic signatures were also studied. Phenomena under study include: wave motions, particularly Alfven and fast mode waves; the formation of standing shocks in the inner heliosphere as a result of momentum and/or heat addition to the wind; and coronal transient phenomena where momentum and/or heat are deposited in the corona to produce transient plasma heating and/or mass ejection. The development of theoretical models for the inner heliosphere, the theoretical investigation of spectroscopic plasma diagnostics for this region, and the analysis of existing skylab and other relevant data are also included.

The use of quizStar application for online examination in basic physics course

NASA Astrophysics Data System (ADS)

Kustijono, R.; Budiningarti, H.

2018-03-01

The purpose of the study is to produce an online Basic Physics exam system using the QuizStar application. This is a research and development with ADDIE model. The steps are: 1) analysis; 2) design; 3) development; 4) implementation; 5) evaluation. System feasibility is reviewed for its validity, practicality, and effectiveness. The subjects of research are 60 Physics Department students of Universitas Negeri Surabaya. The data analysis used is a descriptive statistic. The validity, practicality, and effectiveness scores are measured using a Likert scale. Criteria feasible if the total score of all aspects obtained is ≥ 61%. The results obtained from the online test system by using QuizStar developed are 1) conceptually feasible to use; 2) the system can be implemented in the Basic Physics assessment process, and the existing constraints can be overcome; 3) student's response to system usage is in a good category. The results conclude that QuizStar application is eligible to be used for online Basic Physics exam system.

Transforming community access to space science models

NASA Astrophysics Data System (ADS)

MacNeice, Peter; Hesse, Michael; Kuznetsova, Maria; Maddox, Marlo; Rastaetter, Lutz; Berrios, David; Pulkkinen, Antti

2012-04-01

Researching and forecasting the ever changing space environment (often referred to as space weather) and its influence on humans and their activities are model-intensive disciplines. This is true because the physical processes involved are complex, but, in contrast to terrestrial weather, the supporting observations are typically sparse. Models play a vital role in establishing a physically meaningful context for interpreting limited observations, testing theory, and producing both nowcasts and forecasts. For example, with accurate forecasting of hazardous space weather conditions, spacecraft operators can place sensitive systems in safe modes, and power utilities can protect critical network components from damage caused by large currents induced in transmission lines by geomagnetic storms.

Transforming Community Access to Space Science Models

NASA Technical Reports Server (NTRS)

MacNeice, Peter; Heese, Michael; Kunetsova, Maria; Maddox, Marlo; Rastaetter, Lutz; Berrios, David; Pulkkinen, Antti

2012-01-01

Researching and forecasting the ever changing space environment (often referred to as space weather) and its influence on humans and their activities are model-intensive disciplines. This is true because the physical processes involved are complex, but, in contrast to terrestrial weather, the supporting observations are typically sparse. Models play a vital role in establishing a physically meaningful context for interpreting limited observations, testing theory, and producing both nowcasts and forecasts. For example, with accurate forecasting of hazardous space weather conditions, spacecraft operators can place sensitive systems in safe modes, and power utilities can protect critical network components from damage caused by large currents induced in transmission lines by geomagnetic storms.

Advances in polycrystalline thin-film photovoltaics for space applications

NASA Technical Reports Server (NTRS)

Lanning, Bruce R.; Armstrong, Joseph H.; Misra, Mohan S.

1994-01-01

Polycrystalline, thin-film photovoltaics represent one of the few (if not the only) renewable power sources which has the potential to satisfy the demanding technical requirements for future space applications. The demand in space is for deployable, flexible arrays with high power-to-weight ratios and long-term stability (15-20 years). In addition, there is also the demand that these arrays be produced by scalable, low-cost, high yield, processes. An approach to significantly reduce costs and increase reliability is to interconnect individual cells series via monolithic integration. Both CIS and CdTe semiconductor films are optimum absorber materials for thin-film n-p heterojunction solar cells, having band gaps between 0.9-1.5 ev and demonstrated small area efficiencies, with cadmium sulfide window layers, above 16.5 percent. Both CIS and CdTe polycrystalline thin-film cells have been produced on a laboratory scale by a variety of physical and chemical deposition methods, including evaporation, sputtering, and electrodeposition. Translating laboratory processes which yield these high efficiency, small area cells into the design of a manufacturing process capable of producing 1-sq ft modules, however, requires a quantitative understanding of each individual step in the process and its (each step) effect on overall module performance. With a proper quantification and understanding of material transport and reactivity for each individual step, manufacturing process can be designed that is not 'reactor-specific' and can be controlled intelligently with the design parameters of the process. The objective of this paper is to present an overview of the current efforts at MMC to develop large-scale manufacturing processes for both CIS and CdTe thin-film polycrystalline modules. CIS cells/modules are fabricated in a 'substrate configuration' by physical vapor deposition techniques and CdTe cells/modules are fabricated in a 'superstrate configuration' by wet chemical methods. Both laser and mechanical scribing operations are used to monolithically integrate (series interconnect) the individual cells into modules. Results will be presented at the cell and module development levels with a brief description of the test methods used to qualify these devices for space applications. The approach and development efforts are directed towards large-scale manufacturability of established thin-film, polycrystalline processing methods for large area modules with less emphasis on maximizing small area efficiencies.

Numerical simulation of intense multi-scale vortices generated by supercell thunderstorms

NASA Astrophysics Data System (ADS)

Finley, Catherine Ann

1998-11-01

A nested grid primitive equation model (RAMS version 3b) is used to study various aspects of tornadoes and the thunderstorms that produce them. A unique aspect of these simulations is that the model was initialized with synoptic data, and telescoping grids allow atmospheric flows ranging from the synoptic-scale down to sub- tornado-scale vortices to be represented in the model. Two different case studies were simulated in this study: June 30, 1993, and May 15, 1991. The June 30, 1993, simulation produced a classical supercell storm which developed at the intersection between a stationary front and an outflow boundary generated by previous convection. As the simulation progressed, additional storms developed west of the main storm along the stationary front. One of these storms interacted with the main storm to produce a single supercell storm. This storm had many characteristics of a high-precipitation (HP) supercell, and eventually evolved into a bow-echo. The transition of the storm into a bow-echo is discussed and possible physical processes responsible for the transition are presented. The June 30, 1993, simulated supercell produced two weak tornadoes. The first tornado developed along the flanking line of the storm to the southeast of the mesocyclone. The second tornado developed along a strong horizontal shear zone beneath the rotating comma-head structure of the HP supercell. Neither tornado was clearly linked to the mesocyclone in the parent storm, and both tornadoes formed first near the surface and then developed upward with time. Circulation and vorticity analyses were used to investigate the tornadogenesis process in this case. Results from these analyses indicated that the circulation associated with both tornadoes was already present at low-levels in the storm environment 15-20 minutes before the tornadoes developed. Although the baroclinic term associated with the downdraft air made a negligible contribution to the circulation in this case, the downdraft played an important role in tilting horizontal vorticity into the vertical just above the surface in the near tornado environment where horizontal convergence could then act to amplify it. A comparison with the proposed tornadogenesis process(es) in classical supercells is also presented. The May 15, 1991, simulation produced a classical supercell which developed along the dryline in the Texas panhandle. This supercell in turn produced a tornado which lasted for 50 minutes in the simulation. During a ten minute period toward the end of the simulation, six secondary vortices developed within the main tornado vortex. The simulated secondary vortices had many features in common with multiple-vortex tornadoes and secondary vortices produced in laboratory vortices. The evolution and structure of the simulated secondary vortices is presented, and physical mechanisms responsible for their development and dissipation are discussed.

Lignocellulosic ethanol production at high-gravity: challenges and perspectives.

PubMed

Koppram, Rakesh; Tomás-Pejó, Elia; Xiros, Charilaos; Olsson, Lisbeth

2014-01-01

In brewing and ethanol-based biofuel industries, high-gravity fermentation produces 10-15% (v/v) ethanol, resulting in improved overall productivity, reduced capital cost, and reduced energy input compared to processing at normal gravity. High-gravity technology ensures a successful implementation of cellulose to ethanol conversion as a cost-competitive process. Implementation of such technologies is possible if all process steps can be performed at high biomass concentrations. This review focuses on challenges and technological efforts in processing at high-gravity conditions and how these conditions influence the physiology and metabolism of fermenting microorganisms, the action of enzymes, and other process-related factors. Lignocellulosic materials add challenges compared to implemented processes due to high inhibitors content and the physical properties of these materials at high gravity. Copyright © 2013 Elsevier Ltd. All rights reserved.

Production of the entire range of r-process nuclides by black hole accretion disc outflows from neutron star mergers

NASA Astrophysics Data System (ADS)

Wu, Meng-Ru; Fernández, Rodrigo; Martínez-Pinedo, Gabriel; Metzger, Brian D.

2016-12-01

We consider r-process nucleosynthesis in outflows from black hole accretion discs formed in double neutron star and neutron star-black hole mergers. These outflows, powered by angular momentum transport processes and nuclear recombination, represent an important - and in some cases dominant - contribution to the total mass ejected by the merger. Here we calculate the nucleosynthesis yields from disc outflows using thermodynamic trajectories from hydrodynamic simulations, coupled to a nuclear reaction network. We find that outflows produce a robust abundance pattern around the second r-process peak (mass number A ˜ 130), independent of model parameters, with significant production of A < 130 nuclei. This implies that dynamical ejecta with high electron fraction may not be required to explain the observed abundances of r-process elements in metal poor stars. Disc outflows reach the third peak (A ˜ 195) in most of our simulations, although the amounts produced depend sensitively on the disc viscosity, initial mass or entropy of the torus, and nuclear physics inputs. Some of our models produce an abundance spike at A = 132 that is absent in the Solar system r-process distribution. The spike arises from convection in the disc and depends on the treatment of nuclear heating in the simulations. We conclude that disc outflows provide an important - and perhaps dominant - contribution to the r-process yields of compact binary mergers, and hence must be included when assessing the contribution of these systems to the inventory of r-process elements in the Galaxy.

Characteristics of lipid micro- and nanoparticles based on supercritical formation for potential pharmaceutical application

PubMed Central

2013-01-01

The interest of the pharmaceutical industry in lipid drug delivery systems due to their prolonged release profile, biocompatibility, reduction of side effects, and so on is already known. However, conventional methods of preparation of these structures for their use and production in the pharmaceutical industry are difficult since these methods are usually multi-step and involve high amount of organic solvent. Furthermore, some processes need extreme conditions, which can lead to an increase of heterogeneity of particle size and degradation of the drug. An alternative for drug delivery system production is the utilization of supercritical fluid technique. Lipid particles produced by supercritical fluid have shown different physicochemical properties in comparison to lipid particles produced by classical methods. Such particles have shown more physical stability and narrower size distribution. So, in this paper, a critical overview of supercritical fluid-based processes for the production of lipid micro- and nanoparticles is given and the most important characteristics of each process are highlighted. PMID:24034341

Screening of high temperature adhesives for large area bonding

NASA Technical Reports Server (NTRS)

Stenersen, A. A.; Wykes, D. H.

1980-01-01

High temperature-resistant adhesive systems were screened for processability, mechanical and physical properties, operational capability at 589 K (600 F), and the ability to produce large area bonds of high quality in fabricating Space Shuttle components. The adhesives consisted primarily of polyimide systems, including FM34B-18, NR-150B2 (DuPont), PMR-15, LARC-13, LARC-160, Thermid 600, and AI-1130L (AMOCA). The processing studies included preparation of polyimide resins, fabrication of film adhesives, development of lay-up and cure procedures, fabrication of honeycomb sandwich panels, and fabrication of mid-plane bonded panels in joints up to 30.5 cm (12 in.) wide. The screening program included tests for tack and drape properties, reticulation and filleting characteristics, ability to produce void-free or low porosity bonds in mid-plane bonded panels, out-time stability, lap shear strength, climbing drum peel strength, and glass transition temperature (Tg). This paper describes the processing methods developed and the test results.

The meaning of "natural": process more important than content.

PubMed

Rozin, Paul

2005-08-01

The meaning of the desirable attribute "natural" was explored in two samples, American college students and adults in the Philadelphia jury pool. Participants rated the naturalness of a variety of "natural" entities, before and after they were transformed by operations such as freezing, adding or removing components, mixing with other natural or unnatural entities, domestication, and genetic engineering. Results support four hypotheses. First, the principle of contagion accounts for many aspects of the reduction of naturalness by contact with unnatural entities. Second, chemical transformations reduce naturalness much more than physical transformations do. Third, the history of an entity's processing is more important in determining its naturalness than is the nature of the entity's contents. Fourth, mixing like natural entities (e.g., water from different sources) does not markedly reduce naturalness. The insertion of a gene from another species, the process used in producing genetically modified organisms, produces the biggest drop in naturalness; domestication, a human-accomplished activity that changes genotype and phenotype in major ways, is considered much less damaging to naturalness.

Expanding the molecular-ruler process through vapor deposition of hexadecanethiol

PubMed Central

Patron, Alexandra M; Hooker, Timothy S; Santavicca, Daniel F

2017-01-01

The development of methods to produce nanoscale features with tailored chemical functionalities is fundamental for applications such as nanoelectronics and sensor fabrication. The molecular-ruler process shows great utility for this purpose as it combines top-down lithography for the creation of complex architectures over large areas in conjunction with molecular self-assembly, which enables precise control over the physical and chemical properties of small local features. The molecular-ruler process, which most commonly uses mercaptoalkanoic acids and metal ions to generate metal-ligated multilayers, can be employed to produce registered nanogaps between metal features. Expansion of this methodology to include molecules with other chemical functionalities could greatly expand the overall versatility, and thus the utility, of this process. Herein, we explore the use of alkanethiol molecules as the terminating layer of metal-ligated multilayers. During this study, it was discovered that the solution deposition of alkanethiol molecules resulted in low overall surface coverage with features that varied in height. Because features with varied heights are not conducive to the production of uniform nanogaps via the molecular-ruler process, the vapor-phase deposition of alkanethiol molecules was explored. Unlike the solution-phase deposition, alkanethiol islands produced by vapor-phase deposition exhibited markedly higher surface coverages of uniform heights. To illustrate the applicability of this method, metal-ligated multilayers, both with and without an alkanethiol capping layer, were utilized to create nanogaps between Au features using the molecular-ruler process. PMID:29181290

Fermentation and chemical treatment of pulp and paper mill sludge

DOEpatents

Lee, Yoon Y; Wang, Wei; Kang, Li

2014-12-02

A method of chemically treating partially de-ashed pulp and/or paper mill sludge to obtain products of value comprising taking a sample of primary sludge from a Kraft paper mill process, partially de-ashing the primary sludge by physical means, and further treating the primary sludge to obtain the products of value, including further treating the resulting sludge and using the resulting sludge as a substrate to produce cellulase in an efficient manner using the resulting sludge as the only carbon source and mixtures of inorganic salts as the primary nitrogen source, and including further treating the resulting sludge and using the resulting sludge to produce ethanol.

Enhanced oral bioavailability of vinpocetine through mechanochemical salt formation: physico-chemical characterization and in vivo studies.

PubMed

Hasa, Dritan; Voinovich, Dario; Perissutti, Beatrice; Grassi, Mario; Bonifacio, Alois; Sergo, Valter; Cepek, Cinzia; Chierotti, Michele R; Gobetto, Roberto; Dall'Acqua, Stefano; Invernizzi, Sergio

2011-08-01

Enhancing oral bioavailability of vinpocetine by forming its amorphous citrate salt through a solvent-free mechanochemical process, in presence of micronised crospovidone and citric acid. The impact of formulation and process variables (amount of polymer and citric acid, and milling time) on vinpocetine solubilization kinetics from the coground was studied through an experimental design. The best performing samples were characterized by employing a multidisciplinary approach, involving Differential scanning calorimetry, X-ray diffraction, Raman imaging/spectroscopy, X-ray photoelectron spectroscopy, solid-state NMR spectroscopy, porosimetry and in vivo studies on rats to ascertain the salt formation, their solid-state characteristics and oral bioavailability in comparison to vinpocetine citrate salt (Oxopocetine(®)). The analyses attested that the mechanochemical process is a viable way to produce in absence of solvents vinpocetine citrate salt in an amorphous state. From the in vivo studies on rats the obtained salt was four times more bioavailable than its physical mixture and bioequivalent to the commercial salt produced by conventional synthetic process implying the use of solvent.

Culture-Dependent and -Independent Methods to Investigate the Predominant Microorganisms Associated with Wet Processed Coffee.

PubMed

Feng, Xiaomin; Dong, Honghong; Yang, Pan; Yang, Ruijuan; Lu, Jun; Lv, Jie; Sheng, Jun

2016-08-01

The fermentation process of Yunnan arabica coffee is a typical wet fermentation. Its excellent quality is closely related to microbes in the process of fermentation. The purpose of this study was to isolate and identify the microorganisms in the wet method of coffee processing in Yunnan Province, China. Microbial community structure and dominant bacterial species were evaluated by traditional cultivated separation method and PCR-DGGE technology, and were further analyzed in combination with the changes of organic acid content, activity of pectinase, and physical parameters (pH and temperature). A large number of microorganisms which can produce pectinase were found. Among them, Enterobacter cowanii, Pantoea agglomerans, Enterobacteriaceae bacterium, and Rahnella aquatilis were the predominant gram-negative bacteria, Bacillus cereus was the predominant gram-positive bacterium, Pichia kluyveri, Hanseniaspora uvarum, and Pichia fermentans were the predominant yeasts, and all those are pectinase-producing microorganisms. As for the contents of organic acids, oxalic was the highest, followed by acetic and lactic acids. Butyrate and propionate, which were unfavorable during the fermentation period, were barely discovered.

Electrodeposition of ZnO window layer for an all-atmospheric fabrication process of chalcogenide solar cell

PubMed Central

Tsin, Fabien; Venerosy, Amélie; Vidal, Julien; Collin, Stéphane; Clatot, Johnny; Lombez, Laurent; Paire, Myriam; Borensztajn, Stephan; Broussillou, Cédric; Grand, Pierre Philippe; Jaime, Salvador; Lincot, Daniel; Rousset, Jean

2015-01-01

This paper presents the low cost electrodeposition of a transparent and conductive chlorine doped ZnO layer with performances comparable to that produced by standard vacuum processes. First, an in-depth study of the defect physics by ab-initio calculation shows that chlorine is one of the best candidates to dope the ZnO. This result is experimentally confirmed by a complete optical analysis of the ZnO layer deposited in a chloride rich solution. We demonstrate that high doping levels (>1020 cm−3) and mobilities (up to 20 cm2 V−1 s−1) can be reached by insertion of chlorine in the lattice. The process developed in this study has been applied on a CdS/Cu(In,Ga)(Se,S)2 p-n junction produced in a pilot line by a non vacuum process, to be tested as solar cell front contact deposition method. As a result efficiency of 14.3% has been reached opening the way of atmospheric production of Cu(In,Ga)(Se,S)2 solar cell. PMID:25753657

Electrodeposition of ZnO window layer for an all-atmospheric fabrication process of chalcogenide solar cell.

PubMed

Tsin, Fabien; Venerosy, Amélie; Vidal, Julien; Collin, Stéphane; Clatot, Johnny; Lombez, Laurent; Paire, Myriam; Borensztajn, Stephan; Broussillou, Cédric; Grand, Pierre Philippe; Jaime, Salvador; Lincot, Daniel; Rousset, Jean

2015-03-10

This paper presents the low cost electrodeposition of a transparent and conductive chlorine doped ZnO layer with performances comparable to that produced by standard vacuum processes. First, an in-depth study of the defect physics by ab-initio calculation shows that chlorine is one of the best candidates to dope the ZnO. This result is experimentally confirmed by a complete optical analysis of the ZnO layer deposited in a chloride rich solution. We demonstrate that high doping levels (>10(20) cm(-3)) and mobilities (up to 20 cm(2) V(-1) s(-1)) can be reached by insertion of chlorine in the lattice. The process developed in this study has been applied on a CdS/Cu(In,Ga)(Se,S)2 p-n junction produced in a pilot line by a non vacuum process, to be tested as solar cell front contact deposition method. As a result efficiency of 14.3% has been reached opening the way of atmospheric production of Cu(In,Ga)(Se,S)2 solar cell.

Functionalised particles using dry powder coating in pharmaceutical drug delivery: promises and challenges.

PubMed

Dahmash, Eman Z; Mohammed, Afzal R

2015-01-01

Production of functionalised particles using dry powder coating is a one-step, environmentally friendly process that paves the way for the development of particles with targeted properties and diverse functionalities. Applying the first principles in physical science for powders, fine guest particles can be homogeneously dispersed over the surface of larger host particles to develop functionalised particles. Multiple functionalities can be modified including: flowability, dispersibility, fluidisation, homogeneity, content uniformity and dissolution profile. The current publication seeks to understand the fundamental underpinning principles and science governing dry coating process, evaluate key technologies developed to produce functionalised particles along with outlining their advantages, limitations and applications and discusses in detail the resultant functionalities and their applications. Dry particle coating is a promising solvent-free manufacturing technology to produce particles with targeted functionalities. Progress within this area requires the development of continuous processing devices that can overcome challenges encountered with current technologies such as heat generation and particle attrition. Growth within this field requires extensive research to further understand the impact of process design and material properties on resultant functionalities.

Foam injection molding of poly(lactic acid) with physical blowing agents

NASA Astrophysics Data System (ADS)

Pantani, R.; Sorrentino, A.; Volpe, V.; Titomanlio, G.

2014-05-01

Foam injection molding uses environmental friendly blowing agents under high pressure and temperature to produce parts having a cellular core and a compact solid skin (the so-called "structural foam"). The addition of a supercritical gas reduces the part weight and at the same time improves some physical properties of the material through the promotion of a faster crystallization; it also leads to the reduction of both the viscosity and the glass transition temperature of the polymer melt, which therefore can be injection molded adopting lower temperatures and pressures. These aspects are of extreme interest for biodegradable polymers, which often present a very narrow processing window, with the suitable processing temperatures close to the degradation conditions. In this work, foam injection molding was carried out by an instrumented molding machine, able to measure the pressure evolution in different positions along the flow-path. The material adopted was a biodegradable polymer, namely the Poly(lactic acid), PLA. The effect of a physical blowing agent (PBA) on the viscosity was measured. The density reduction and the morphology of parts obtained by different molding conditions was assessed.

Nuclear Instruments and Methods in Physics Research. Section B; Microstructural Characterization of Semi-Interpenetrating Polymer Networks by Positron Lifetime Spectroscopy

NASA Technical Reports Server (NTRS)

Singh, Jag J.; Pater, Ruth H.; Eftekhari, Abe

1998-01-01

Thermoset and thermoplastic polyimides have complementary physical/mechanical properties. Whereas thermoset polyimides are brittle and generally easier to process, thermoplastic polyimides are tough but harder to process. It is expected that a combination of these two types of polyimides may help produce polymers more suitable for aerospace applications. Semi-Interpenetrating Polymer Networks (S-IPNs) of thermoset LaRC(Trademark)-RP46 and thermoplastic LARC(Trademark)-IA polyimides were prepared in weight percent ratios ranging from 100:0 to 0: 100. Positron lifetime measurements were made in these samples to correlate their free volume features with physical/mechanical properties. As expected, positronium atoms are not formed in these samples. The second life time component has been used to infer the positron trap dimensions. The "free volume" goes through a minimum at about 50:50 ratio, suggesting that S-IPN samples are not merely solid solutions of the two polymers. These data and related structural properties of the S-IPN samples have been discussed in this paper.

Classical Wave Model of Quantum-Like Processing in Brain

NASA Astrophysics Data System (ADS)

Khrennikov, A.

2011-01-01

We discuss the conjecture on quantum-like (QL) processing of information in the brain. It is not based on the physical quantum brain (e.g., Penrose) - quantum physical carriers of information. In our approach the brain created the QL representation (QLR) of information in Hilbert space. It uses quantum information rules in decision making. The existence of such QLR was (at least preliminary) confirmed by experimental data from cognitive psychology. The violation of the law of total probability in these experiments is an important sign of nonclassicality of data. In so called "constructive wave function approach" such data can be represented by complex amplitudes. We presented 1,2 the QL model of decision making. In this paper we speculate on a possible physical realization of QLR in the brain: a classical wave model producing QLR . It is based on variety of time scales in the brain. Each pair of scales (fine - the background fluctuations of electromagnetic field and rough - the cognitive image scale) induces the QL representation. The background field plays the crucial role in creation of "superstrong QL correlations" in the brain.

Planetary nebulae: 20 years of Hubble inquiry

NASA Astrophysics Data System (ADS)

Balick, Bruce

2012-08-01

The Hubble Space Telescope has served the critical roles of microscope and movie camera in the past 20 years of research on planetary nebulae (``PNe''). We have glimpsed the details of the evolving structures of neutral and ionized post-AGB objects, built ingenious heuristic models that mimic these structures, and constrained most of the relevant physical processes with careful observations and interpretation. We have searched for close physical binary stars with spatial resolution ~50 AU at 1 AU, located jets emerging from the nucleus at speeds up to 2000 km s-1 and matched newly discovered molecular and X-ray emission regions to physical substructures in order to better understand how stellar winds and ionizing radiation interact to form the lovely symmetries that are observed. Ultraviolet spectra of CNO in PNe help to uncover how stars process deep inside AGB stars with unstable nuclear burning zones. HST broadband imaging has been at the forefront of uncovering surprisingly complex wind morphologies produced at the tip of the AGB, and has led to an increasing realization of the potentially vital roles of close binary stars and emerging magnetic fields in shaping stellar winds.

A physical mechanism producing suprathermal populations and initiating substorms in the Earth's magnetotail

NASA Astrophysics Data System (ADS)

Sarafopoulos, D. V.

2008-06-01

We suggest a candidate physical mechanism, combining there dimensional structure and temporal development, which is potentially able to produce suprathermal populations and cross-tail current disruptions in the Earth's plasma sheet. At the core of the proposed process is the "akis" structure; in a thin current sheet (TCS) the stretched (tail-like) magnetic field lines locally terminate into a sharp tip around the tail midplane. At this sharp tip of the TCS, ions become non-adiabatic, while a percentage of electrons are accumulated and trapped: The strong and transient electrostatic electric fields established along the magnetic field lines produce suprathermal populations. In parallel, the tip structure is associated with field aligned and mutually attracted parallel filamentary currents which progressively become more intense and inevitably the structure collapses, and so does the local TCS. The mechanism is observationally based on elementary, almost autonomous and spatiotemporal entities that correspond each to a local thinning/dipolarization pair having duration of ~1 min. Energetic proton and electron populations do not occur simultaneously, and we infer that they are separately accelerated at local thinnings and dipolarizations, respectively. In one example energetic particles are accelerated without any dB/dt variation and before the substorm expansion phase onset. A particular effort is undertaken demonstrating that the proposed acceleration mechanism may explain the plasma sheet ratio Ti/Te≍7. All our inferences are checked by the highest resolution datasets obtained by the Geotail Energetic Particles and Ion Composition (EPIC) instrument. The energetic particles are used as the best diagnostics for the accelerating source. Near Earth (X≍10 RE) selected events support our basic concept. The proposed mechanism seems to reveal a fundamental building block of the substorm phenomenon and may be the basic process/structure, which is now missing, that might help explain the persistent, outstanding deficiencies in our physical description of magnetospheric substorms. The mechanism is tested, checked, and found consistent with substorm associated observations performed ~30 and 60 RE away from Earth.

Institutional Producers of Physics Research.

ERIC Educational Resources Information Center

Cooper, Marianne; Watterson, Hermine M.

In order to identify producers of physics research and to determine their relative productivity, institutional affiliations of authors as given in nine physics journals were studied. Organizations were classified and analyzed by type and geographical location, and productivity established. Findings indicate that organizations differ in their rate…

Development of a continuous spinning process for producing silicon carbide - silicon nitride precursor fibers

NASA Technical Reports Server (NTRS)

1985-01-01

An apparatus was designed for the continuous production of silicon carbide - silicon nitride precursor fibers. The precursor polymer can be fiberized, crosslined and pyrolyzed. The product is a metallic black fiber with the composition of the type C sub x Si sub y n sub z. Little, other than the tensile strength and modulus of elasticity, is known of the physical properties.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Potamianos, Karolos Jozef

We study rare processes of the standard model of particle physics (SM) in events with missing transverse energy E T, no leptons, and two or three jets, of which at least one is identified as originating from amore » $b$-quark (E T+b-jets signature). We present a search for the SM Higgs boson produced in association with a $W$ or $Z$$ boson when the Higgs decays into \\bbbar. We consider the scenario where $$Z \\to \

Advanced physical fine coal cleaning: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1987-12-01

The contract objective was to demonstrate Advanced Energy Dynamics, Inc., (AED) Ultrafine Coal (UFC) electrostatic physical fine coal cleaning process as capable of: producing clean coal products of no greater than 2% ash; significantly reducing the pyritic sulfur content below that achievable with state-of-the-art coal cleaning; recovering over 80% of the available energy content in the run-of-mine coal; producing product and refuse with surface moisture below 30%. Originally the demonstration was to be of a Charger/Disc System at the Electric Power Research Institute (EPRI) Coal Quality Development Center (CQDC) at Homer City, Pennsylvania. As a result of the combination ofmore » Charger/Disc System scale-up problems and parallel development of an improved Vertical-Belt Separator, DOE issued a contract modification to perform additional laboratory testing and optimization of the UFC Vertical-Belt Separator System at AED. These comparative test results, safety analyses and an economic analysis are discussed in this report. 29 refs., 25 figs., 41 tabs.« less

Effect of potassium sorbate on antimicrobial and physical properties of starch-clay nanocomposite films.

PubMed

Barzegar, Hassan; Azizi, Mohammad Hossein; Barzegar, Mohsen; Hamidi-Esfahani, Zohreh

2014-09-22

Using fresh foods which undergo the least processing operations developed widely in recent years. Active packaging is a novel method for preserving these products. Active starch-clay nanocomposite films which contained potassium sorbate (PS) at a level of 0, 5, 7.5 and 10 g PS/100 g starch were produced and their physical, mechanical and antimicrobial properties were evaluated. In order to evaluate antimicrobial properties of films Aspergillus niger was used. The results showed that 5% of the PS did not produce antimicrobial property in the film, but by increasing the content of the additive in film formulation, antimicrobial effect increased. PS increased water permeability and elongation at break of the films, but decreased tensile strength. The rate of PS migration into the semi-solid medium in starch-nanocomposites was lower than starch films. This shows that nanocomposite films could retain their antimicrobial property for longer time. Copyright © 2014 Elsevier Ltd. All rights reserved.

Recovery of plastic wastes from dumpsite as refuse-derived fuel and its utilization in small gasification system.

PubMed

Chiemchaisri, Chart; Charnnok, Boonya; Visvanathan, Chettiyappan

2010-03-01

An effort to utilize solid wastes at dumpsite as refuse-derived fuel (RDF) was carried out. The produced RDF briquette was then utilized in the gasification system. These wastes were initially examined for their physical composition and chemical characteristics. The wastes contained high plastic content of 24.6-44.8%, majority in polyethylene plastic bag form. The plastic wastes were purified by separating them from other components through manual separation and trommel screen after which their content increased to 82.9-89.7%. Subsequently, they were mixed with binding agent (cassava root) and transformed into RDF briquette. Maximum plastic content in RDF briquette was limit to 55% to maintain physical strength and maximum chlorine content. The RDF briquette was tested in a down-draft gasifier. The produced gas contained average energy content of 1.76 MJ/m(3), yielding cold gas efficiency of 66%. The energy production cost from this RDF process was estimated as USD0.05 perkWh. 2009 Elsevier Ltd. All rights reserved.

Microcalorimeter X-ray Detectors for Solar Physics

NASA Astrophysics Data System (ADS)

Deiker, S.; Boerner, P.; Martinez-Galarce, D.; Metcalf, T.; Rausch, A.; Shing, L.; Stern, R.; Irwin, K.; William, D.; Reintsema, C.; Ullom, J.; Cabrera, B.; Lehman, S.; Brink, P.

2005-05-01

Cryogenic X-ray microcalorimeters provide high spectral resolution over a large bandwidth. They have achieved < 3 eV resolution at 5.9 keV, and can produce this performance simultaneously from 0.25 to 10 keV. Although they operate at low (< 0.1 K) temperatures, such temperature are now easily produced. Microcalorimeters cooled by adiabatic demagnetization refrigerators have already flown on sounding rocket flights to study the soft X-ray background of the interstellar medium, and will soon be launched on the ASTRO-E II satellite. Microcalorimeters based on superconducting transition edge sensors are multiplexable and may be fabricated using standard photolithographic techniques. This makes large arrays of microcalorimeters feasible. Each pixel of such an array detects the arrival time of each photon to within < 0.01 ms. Such an instrument would offer simultaneous spatial, temporal and energy resolution, bringing a wealth of new information about solar processes. Current design and performance of microcalorimeters will be presented. Future improvements required to optimize microcalorimeters for solar physics applications will also be discussed.

Studies of the linear and nonlinear properties of Alfvén waves in LAPD

NASA Astrophysics Data System (ADS)

Carter, Troy; Dorfman, Seth; Gekelman, Walter; Tripathi, Shreekrishna; van Compernolle, Bart; Vincena, Steve; Rossi, Giovanni; Jenko, Frank

2015-11-01

An overview will be given of recent experimental research into linear and nonlinear properties of Alfvén waves in the Large Plasma Device (LAPD). The nonlinear three-wave interaction process at the heart of the parametric decay instability is studied by launching counter-propagating Alfvén waves from antennas placed at either end of LAPD, producing a damped ion acoustic mode. The decay of a lone, large amplitude Alfvén wave has been observed, producing co-propagating daughter waves with characteristics consistent with kinetic Alfvén waves. The process has an amplitude threshold and the frequency of the daughter modes varies with the amplitude of the pump. A new plasma source based on LaB6 cathode has been added to LAPD, enabling much higher density (x50), electron temperature (x2) and ion temperature (x6). This provides the opportunity to study the physics of waves and instabilities with space and astrophysically relevant β. Topics under investigation include the physics of Alfvén waves in increased β plasmas, electromagnetic effects in drift-Alfvén wave turbulence and the excitation of ion-temperature-anisotropy driven modes such as the mirror and firehose. Supported by NSF and DOE.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Góźdź, A., E-mail: andrzej.gozdz@umcs.lublin.pl; Góźdź, M., E-mail: mgozdz@kft.umcs.lublin.pl

The theory of neutrino oscillations rests on the assumption, that the interaction basis and the physical (mass) basis of neutrino states are different. Therefore neutrino is produced in a certain welldefined superposition of three mass eigenstates, which propagate separately and may be detected as a different superposition. This is called flavor oscillations. It is, however, not clear why neutrinos behave this way, i.e., what is the underlying mechanism which leads to the production of a superposition of physical states in a single reaction. In this paper we argue, that one of the reasons may be connected with the temporal structuremore » of the process. In order to discuss the role of time in processes on the quantum level, we use a special formulation of the quantum mechanics, which is based on the projection time evolution. We arrive at the conclusion, that for short reaction times the formation of a superposition of states of similar masses is natural.« less

The Physics of Molecular Shocks in Star-Forming Regions

NASA Technical Reports Server (NTRS)

Hollenbach, David; Cuzzi, Jeffrey (Technical Monitor)

1996-01-01

Molecular shocks are produced by the impact of the supersonic infall of gas and dust onto protostars and by the interaction of the supersonic outflow from the protostar with the circumstellar material. Infalling gas creates an accretion shock around the circumstellar disk which emits a unique infrared spectrum and which processes the interstellar dust as it enters the disk. The winds and jets from protostars also impact the disk, the infalling material, and the ambient molecular cloud core creating shocks whose spectrum and morphology diagnose the mass loss processes of the protostar and the orientation and structure of the star forming system. We discuss the physics of these shocks, the model spectra derived from theoretical models, and comparisons with observations of H2O masers, H2 emission, as well as other shocks tracers. We show the strong effect of magnetic fields on molecular shock structure, and elucidate the chemical changes induced by the shock heating and compression.

The way to universal and correct medical presentation of diagnostic informations for complex spectrophotometry noninvasive medical diagnostic systems

NASA Astrophysics Data System (ADS)

Rogatkin, Dmitrii A.; Tchernyi, Vladimir V.

2003-07-01

The optical noninvasive diagnostic systems are now widely applied and investigated in different areas of medicine. One of the such techniques is the noninvasive spectrophotometry, the complex diagnostic technique consisting on elastic scattering spectroscopy, absorption spectroscopy, fluorescent diagnostics, photoplethismography, etc. Today a lot of real optical diagnostic systems indicate the technical parameters and physical data only as a result of the diagnostic procedure. But, it is clear that for the medical staff the more convenient medical information is needed. This presentation lights the general way for development a diagnostic system"s software, which can produce the full processing of the diagnostic data from a physical to a medical level. It is shown, that this process is a multilevel (3-level) procedure and the main diagnostic result for noninvasive spectrophotometry methods, the biochemical and morphological composition of the tested tissues, arises in it on a second level of calculations.

Dust in Jupiter's magnetosphere. I - Physical processes. II - Origin of the ring. III - Time variations. IV - Effect on magnetospheric electrons and ions

NASA Technical Reports Server (NTRS)

Morfill, G. E.; Gruen, E.; Johnson, T. V.

1980-01-01

The physical processes acting on charged microscopic dust grains in the Jovian atmosphere involve electromagnetic forces which dominate dust particle dynamics and diffusion across field lines resulting from random charge fluctuations of the dust grains. A model of the Jovian ring hypothesizes that the 'visible' ring particles are produced by erosive collisions between an assumed population of kilometer-sized parent bodies and submicron-sized magnetospheric dust particles. Fluctuations in the ring topology and intensity are determined over various time scales, showing that the ring is a quasipermanent and quasistable characteristic of the Jovian system. Finally, the interaction of the Jovian energetic belt electrons and the Jovian plasma with an ambient dust population is examined; the distribution of dust ejected from Io in the inner magnetosphere and losses of magnetospheric ions and electrons due to direct collisions with charged dust particles are calculated.

Modern meta-heuristics based on nonlinear physics processes: A review of models and design procedures

NASA Astrophysics Data System (ADS)

Salcedo-Sanz, S.

2016-10-01

Meta-heuristic algorithms are problem-solving methods which try to find good-enough solutions to very hard optimization problems, at a reasonable computation time, where classical approaches fail, or cannot even been applied. Many existing meta-heuristics approaches are nature-inspired techniques, which work by simulating or modeling different natural processes in a computer. Historically, many of the most successful meta-heuristic approaches have had a biological inspiration, such as evolutionary computation or swarm intelligence paradigms, but in the last few years new approaches based on nonlinear physics processes modeling have been proposed and applied with success. Non-linear physics processes, modeled as optimization algorithms, are able to produce completely new search procedures, with extremely effective exploration capabilities in many cases, which are able to outperform existing optimization approaches. In this paper we review the most important optimization algorithms based on nonlinear physics, how they have been constructed from specific modeling of a real phenomena, and also their novelty in terms of comparison with alternative existing algorithms for optimization. We first review important concepts on optimization problems, search spaces and problems' difficulty. Then, the usefulness of heuristics and meta-heuristics approaches to face hard optimization problems is introduced, and some of the main existing classical versions of these algorithms are reviewed. The mathematical framework of different nonlinear physics processes is then introduced as a preparatory step to review in detail the most important meta-heuristics based on them. A discussion on the novelty of these approaches, their main computational implementation and design issues, and the evaluation of a novel meta-heuristic based on Strange Attractors mutation will be carried out to complete the review of these techniques. We also describe some of the most important application areas, in broad sense, of meta-heuristics, and describe free-accessible software frameworks which can be used to make easier the implementation of these algorithms.

Increasing Diversity at the PhD Level in Astronomy: The Fisk-Vanderbilt Masters-to-PhD Bridge Program

NASA Astrophysics Data System (ADS)

Stassun, Keivan; Holley-Bockelmann, K.; Berlind, A. A.

2013-01-01

We briefly review the current status of underrepresented minorities in the physical sciences: The underrepresentation of Black-, Hispanic-, and Native-Americans is an order of magnitude problem. We then describe the Fisk-Vanderbilt Masters-to-PhD Bridge program as a successful model for effective partnerships with minority-serving institutions toward addressing this problem. Since 2004 the program has admitted 60 students, 54 of them underrepresented minorities (60% female), with a retention rate of 92%. The program leads the nation in master’s degrees in physics for African Americans, is one of the top ten producers of physics master’s degrees among all US citizens in general, and has become the nation’s top producer of underrepresented minority PhDs in physics, astronomy, and materials science. We summarize the main features of the program including two of its core strategies: (1) partnering a minority-serving institution and a major research university through collaborative research, and (2) using the master’s degree as a deliberate stepping stone to the PhD. We also specifically discuss one of the emerging core theories of the program: the concept of properly identifying students with 'unrealized or unrecognized potential'. We discuss our methods to recognize and select for unrealized potential during the admissions process, and how we cultivate that unrealized potential toward development of successful scientists and leaders.

Impact of food processing and detoxification treatments on mycotoxin contamination.

PubMed

Karlovsky, Petr; Suman, Michele; Berthiller, Franz; De Meester, Johan; Eisenbrand, Gerhard; Perrin, Irène; Oswald, Isabelle P; Speijers, Gerrit; Chiodini, Alessandro; Recker, Tobias; Dussort, Pierre

2016-11-01

Mycotoxins are fungal metabolites commonly occurring in food, which pose a health risk to the consumer. Maximum levels for major mycotoxins allowed in food have been established worldwide. Good agricultural practices, plant disease management, and adequate storage conditions limit mycotoxin levels in the food chain yet do not eliminate mycotoxins completely. Food processing can further reduce mycotoxin levels by physical removal and decontamination by chemical or enzymatic transformation of mycotoxins into less toxic products. Physical removal of mycotoxins is very efficient: manual sorting of grains, nuts, and fruits by farmers as well as automatic sorting by the industry significantly lowers the mean mycotoxin content. Further processing such as milling, steeping, and extrusion can also reduce mycotoxin content. Mycotoxins can be detoxified chemically by reacting with food components and technical aids; these reactions are facilitated by high temperature and alkaline or acidic conditions. Detoxification of mycotoxins can also be achieved enzymatically. Some enzymes able to transform mycotoxins naturally occur in food commodities or are produced during fermentation but more efficient detoxification can be achieved by deliberate introduction of purified enzymes. We recommend integrating evaluation of processing technologies for their impact on mycotoxins into risk management. Processing steps proven to mitigate mycotoxin contamination should be used whenever necessary. Development of detoxification technologies for high-risk commodities should be a priority for research. While physical techniques currently offer the most efficient post-harvest reduction of mycotoxin content in food, biotechnology possesses the largest potential for future developments.

Electro fluido dynamic techniques to design instructive biomaterials for tissue engineering and drug delivery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guarino, Vincenzo, E-mail: vguarino@unina.it; Altobelli, Rosaria; Cirillo, Valentina

A large variety of processes and tools is continuously investigated to discover new solutions to design instructive materials with controlled chemical, physical and biological properties for tissue engineering and drug delivery. Among them, electro fluido dynamic techniques (EFDTs) are emerging as an interesting strategy, based on highly flexible and low-cost processes, to revisit old biomaterial’s manufacturing approach by utilizing electrostatic forces as the driving force for the fabrication of 3D architectures with controlled physical and chemical functionalities to guide in vitro and in vivo cell activities. By a rational selection of polymer solution properties and process conditions, EFDTs allow tomore » produce fibres and/or particles at micro and/or nanometric size scale which may be variously assembled by tailored experimental setups, thus giving the chance to generate a plethora of different 3D devices able to incorporate biopolymers (i.e., proteins, polysaccharides) or active molecules (e.g., drugs) for different applications. Here, we focus on the optimization of basic EFDTs - namely electrospinning, electrospraying and electrodynamic atomization - to develop active platforms (i.e., monocomponent, protein and drug loaded scaffolds and µ-scaffolds) made of synthetic (PCL, PLGA) or natural (chitosan, alginate) polymers. In particular, we investigate how to set materials and process parameters to impart specific morphological, biochemical or physical cues to trigger all the fundamental cell–biomaterial and cell– cell cross-talking elicited during regenerative processes, in order to reproduce the complex microenvironment of native or pathological tissues.« less

Electro fluido dynamic techniques to design instructive biomaterials for tissue engineering and drug delivery

NASA Astrophysics Data System (ADS)

Guarino, Vincenzo; Altobelli, Rosaria; Cirillo, Valentina; Ambrosio, Luigi

2015-12-01

A large variety of processes and tools is continuously investigated to discover new solutions to design instructive materials with controlled chemical, physical and biological properties for tissue engineering and drug delivery. Among them, electro fluido dynamic techniques (EFDTs) are emerging as an interesting strategy, based on highly flexible and low-cost processes, to revisit old biomaterial's manufacturing approach by utilizing electrostatic forces as the driving force for the fabrication of 3D architectures with controlled physical and chemical functionalities to guide in vitro and in vivo cell activities. By a rational selection of polymer solution properties and process conditions, EFDTs allow to produce fibres and/or particles at micro and/or nanometric size scale which may be variously assembled by tailored experimental setups, thus giving the chance to generate a plethora of different 3D devices able to incorporate biopolymers (i.e., proteins, polysaccharides) or active molecules (e.g., drugs) for different applications. Here, we focus on the optimization of basic EFDTs - namely electrospinning, electrospraying and electrodynamic atomization - to develop active platforms (i.e., monocomponent, protein and drug loaded scaffolds and µ-scaffolds) made of synthetic (PCL, PLGA) or natural (chitosan, alginate) polymers. In particular, we investigate how to set materials and process parameters to impart specific morphological, biochemical or physical cues to trigger all the fundamental cell-biomaterial and cell- cell cross-talking elicited during regenerative processes, in order to reproduce the complex microenvironment of native or pathological tissues.

The Vapor Deposition Model of Space Weathering: A Strawman Paradigm for the Moon

NASA Astrophysics Data System (ADS)

Hapke, Bruce W.

1998-01-01

Understanding space weathering on the lunar surface is essential to solving a number of major problems, including correctly interpreting lunar remote-sensing observations, understanding physical and chemical processes in the lunar regolith, and extrapolating to other bodies, especially Mercury, the asteroids, and the parent bodies of the ordinary chondrites. Hence, it is of great importance to correctly identify the process or processes that dominate lunar space weathering. The vapor deposition model postulates that lunar space weathering occurs as a result of the production of submicrscopic metallic iron (SMFe, also called superparamagnetic iron and nanophase iron) particles in the regolith by the intrinsic differentiation that accompanies the deposition of silicate vapor produced by both solar wind sputtering and micrometeorite impacts. This is the only process that has been demonstrated repeatedly by laboratory experiments to be capable of selectively producing SMFe. Hence, at present, it must be regarded as the leading contender for the correct model of lunar space weathering. This paper reviews the features of the vapor deposition model. The basic mechanism of the model relies on the fact that the porous microrelief of the lunar regolith allows most of the vapor produced by sputtering and impacts to be retained in the soil, rather than escaping from the Moon. As the individual vapor atoms impact the soil grain surfaces, they are first weakly bound by physical adsorption processes, and so have a finite probability of desorbing and escaping. Since the O is the most volatile, it escapes preferentially. The remaining atoms become chemically bound and form amorphous coatings on lunar soil grains. Because Fe is the most easily reduced of the major cations in the soil, the O deficiency manifests itself in the form of interstitial Fe0 in the glass deposits. Subsequent heating by impacts allows the Feo atoms to congregate together by solid-state diffusion to form SMFe grains. The impacts dislodge some of the coatings, which form an additional component of the soil, and also shock-weld the mineral grains, impact-vitrified glass, and vapor-deposited glass into agglutinates. Glass generated by impact vitrification probably plays a negligible role in lunar optical properties.

Gaussian process model for extrapolation of scattering observables for complex molecules: From benzene to benzonitrile

NASA Astrophysics Data System (ADS)

Cui, Jie; Li, Zhiying; Krems, Roman V.

2015-10-01

We consider a problem of extrapolating the collision properties of a large polyatomic molecule A-H to make predictions of the dynamical properties for another molecule related to A-H by the substitution of the H atom with a small molecular group X, without explicitly computing the potential energy surface for A-X. We assume that the effect of the -H →-X substitution is embodied in a multidimensional function with unknown parameters characterizing the change of the potential energy surface. We propose to apply the Gaussian Process model to determine the dependence of the dynamical observables on the unknown parameters. This can be used to produce an interval of the observable values which corresponds to physical variations of the potential parameters. We show that the Gaussian Process model combined with classical trajectory calculations can be used to obtain the dependence of the cross sections for collisions of C6H5CN with He on the unknown parameters describing the interaction of the He atom with the CN fragment of the molecule. The unknown parameters are then varied within physically reasonable ranges to produce a prediction uncertainty of the cross sections. The results are normalized to the cross sections for He — C6H6 collisions obtained from quantum scattering calculations in order to provide a prediction interval of the thermally averaged cross sections for collisions of C6H5CN with He.

Lignin plays a negative role in the biochemical process for producing lignocellulosic biofuels.

PubMed

Zeng, Yining; Zhao, Shuai; Yang, Shihui; Ding, Shi-You

2014-06-01

A biochemical platform holds the most promising route toward lignocellulosic biofuels, in which polysaccharides are hydrolyzed by cellulase enzymes into simple sugars and fermented to ethanol by microbes. However, these polysaccharides are cross-linked in the plant cell walls with the hydrophobic network of lignin that physically impedes enzymatic deconstruction. A thermochemical pretreatment process is often required to remove or delocalize lignin, which may also generate inhibitors that hamper enzymatic hydrolysis and fermentation. Here we review recent advances in understanding lignin structure in the plant cell walls and the negative roles of lignin in the processes of converting biomass to biofuels. Perspectives and future directions to improve the biomass conversion process are also discussed. Copyright © 2013. Published by Elsevier Ltd.

Element Genesis - Solving the Mystery (Video Presentation)

NASA Astrophysics Data System (ADS)

Mochizuki, Yuko

2001-10-01

Our institute (RIKEN) produced a video on nucleosynthesis. Its new English version is presented. Y. M., I. Tanihata, Y. Yano, and R. Boyd are science editors for this. Time length of the video is 30 minutes. The primary characteristic of this video is that we have employed a number of 2-D and 3-Dimensional visualizations and animations based on an updated understanding of nuclear physics and astrophysics. One of the emphasized points is that microscopic physics (i.e., nuclear physics) and macroscopic physics (i.e., astrophysics) are strongly connected. It contains explanation on the chart of the nuclides, nuclear burning in the sun, big-bang nucleosynthesis, stellar nucleosynthesis, ``beta-stability valley", the s-process, the r-process, production of an RI beam, etc., and professors D. Arnett, T. Kajino, K. Langanke, K. Sato, C. Sneden, I. Tanihata, and F.-K. Thielemann appear as interviewees. Our prime target is college freshmen. We hope that this video would be useful for education both in the fields of astrophysics and nuclear physics at universities and even at high schools. Our institute is accordingly developing a distribution system of this video and it will be available soon at the cost price (please visit our web site for details: http://www.rarf.riken.go.jp/video). The Japanese version was awarded the prize of the Minister of Education, Culture, Sports, Science, and Technology of Japan 2001.

Corrosion resistance and biological activity of TiO2 implant coatings produced in oxygen-rich environments.

PubMed

Zhang, Rui; Wan, Yi; Ai, Xing; Liu, Zhanqiang; Zhang, Dong

2017-01-01

The physical and chemical properties of bio-titanium alloy implant surfaces play an important role in their corrosion resistance and biological activity. New turning and turning-rolling processes are presented, employing an oxygen-rich environment in order to obtain titanium dioxide layers that can both protect implants from corrosion and also promote cell adhesion. The surface topographies, surface roughnesses and chemical compositions of the sample surfaces were obtained using scanning electron microscopy, a white light interferometer, and the Auger electron spectroscopy, respectively. The corrosion resistance of the samples in a simulated body fluid was determined using electrochemical testing. Biological activity on the samples was also analyzed, using a vitro cell culture system. The results show that compared with titanium oxide layers formed using a turning process in air, the thickness of the titanium oxide layers formed using turning and turning-rolling processes in an oxygen-rich environment increased by 4.6 and 7.3 times, respectively. Using an oxygen-rich atmosphere in the rolling process greatly improves the corrosion resistance of the resulting samples in a simulated body fluid. On samples produced using the turning-rolling process, cells spread quickly and exhibited the best adhesion characteristics.

Respiratory factors in the uptake and excretion of anesthetics. 1965.

PubMed

Epstein, R M; Papper, E M

1998-01-01

We have considered some of the ways in which respiration can affect the gas exchange process. The simplest relationships are purely physical and relate to the speed with which the lung and tissues can be filled or emptied. More complex relationships involve a consideration of the interplay between blood and gas in the lung and the effects of gas exchange on respiratory volumes themselves. Finally, some examples of the importance of physiologic alteration produced by, and producing respiratory shifts during, gas uptake processes were presented briefly. The detailed interpretation of gas exchange phenomena demands more quantitative information of this sort, concerning not only the respiratory but the circulatory and tissue level variations affecting uptake during anesthesia. Nevertheless, understanding of the principles and application of such data as are available can go far toward removing the handicaps of empirical practice from the day-to-day administration of anesthetic agents to human beings.

Present status of metrology of electro-optical surveillance systems

NASA Astrophysics Data System (ADS)

Chrzanowski, K.

2017-10-01

There has been a significant progress in equipment for testing electro-optical surveillance systems over the last decade. Modern test systems are increasingly computerized, employ advanced image processing and offer software support in measurement process. However, one great challenge, in form of relative low accuracy, still remains not solved. It is quite common that different test stations, when testing the same device, produce different results. It can even happen that two testing teams, while working on the same test station, with the same tested device, produce different results. Rapid growth of electro-optical technology, poor standardization, limited metrology infrastructure, subjective nature of some measurements, fundamental limitations from laws of physics, tendering rules and advances in artificial intelligence are major factors responsible for such situation. Regardless, next decade should bring significant improvements, since improvement in measurement accuracy is needed to sustain fast growth of electro-optical surveillance technology.

A review of carbide fuel corrosion for nuclear thermal propulsion applications

NASA Astrophysics Data System (ADS)

Pelaccio, Dennis G.; El-Genk, Mohamed S.; Butt, Darryl P.

1993-10-01

At the operation conditions of interest in nuclear thermal propulsion reactors, carbide materials have been known to exhibit a number of life limiting phenomena. These include the formation of liquid, loss by vaporization, creep and corresponding gas flow restrictions, and local corrosion and fuel structure degradation due to excessive mechanical and/or thermal loading. In addition, the radiation environment in the reactor core can produce a substantial change in its local physical properties, which can produce high thermal stresses and corresponding stress fractures (cracking). Time-temperature history and cyclic operation of the nuclear reactor can also accelerate some of these processes. The University of New Mexico's Institute for Space Nuclear Power Studies, under NASA sponsorship has recently initiated a study to model the complicated hydrogen corrosion process. In support of this effort, an extensive review of the open literature was performed, and a technical expert workshop was conducted. This paper summarizes the results of this review.

A Review of Carbide Fuel Corrosion for Nuclear Thermal Propulsion Applications

NASA Astrophysics Data System (ADS)

Pelaccio, Dennis G.; El-Genk, Mohamed S.; Butt, Darryl P.

1994-07-01

At the operation conditions of interest in nuclear thermal propulsion reactors, carbide materials have been known to exhibit a number of life limiting phenomena. These include the formation of liquid, loss by vaporization, creep and corresponding gas flow restrictions, and local corrosion and fuel structure degradation due to excessive mechanical and/or thermal loading. In addition, the radiation environment in the reactor core can produce a substantial change in its local physical properties, which can produce high thermal stresses and corresponding stress fractures (cracking). Time-temperature history and cyclic operation of the nuclear reactor can also accelerate some of these processes. The University of New Mexico's Institute for Space Nuclear Power Studies, under NASA sponsorship has recently initiated a study to model the complicated hydrogen corrosion process. In support of this effort, an extensive review of the open literature was performed, and a technical expert workshop was conducted. This paper summarizes the results of this review.

Chemistry of Martian Soils from the Mars Exploration Rover APXS Instruments

NASA Technical Reports Server (NTRS)

Mittlefehldt, D. W.; Gellert, R.; Yen, A.

2007-01-01

The martian surface is covered with debris formed by several mechanisms and mobilized by various processes. Volcanism, impact, physical weathering and chemical alteration combine to produce particles of sizes from dust to boulders composed of primary mineral and rock fragments, partially altered primary materials, alteration minerals and shock-modified materials from all of these. Impacts and volcanism produce localized deposits. Winds transport roughly sand-sized material over intermediate distances, while periodic dust storms deposit a global dust layer of the finest fraction. The compositions of clastic sediments can be used to evaluate regional differences in crustal composition and/or weathering processes. Here we examine the growing body of chemical data on soils in Gusev crater and Meridiani Planum returned by the Alpha Particle X-ray Spectrometer (APXS) instruments on the rovers Spirit (MERA) and Opportunity (MERB), following on earlier results based on smaller data sets [1-4].

ICFA Beam Dynamics Newsletter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pikin, A.

2017-11-21

Electron beam ion sources technology made significant progress since 1968 when this method of producing highly charged ions in a potential trap within electron beam was proposed by E. Donets. Better understanding of physical processes in EBIS, technological advances and better simulation tools determined significant progress in key EBIS parameters: electron beam current and current density, ion trap capacity, attainable charge states. Greatly increased the scope of EBIS and EBIT applications. An attempt is made to compile some of EBIS engineering problems and solutions and to demonstrate a present stage of understanding the processes and approaches to build a bettermore » EBIS.« less

Hillslope Evolution by Bedrock Landslides

PubMed

Densmore; Anderson; McAdoo; Ellis

1997-01-17

Bedrock landsliding is a dominant geomorphic process in a number of high-relief landscapes, yet is neglected in landscape evolution models. A physical model of sliding in beans is presented, in which incremental lowering of one wall simulates baselevel fall and generates slides. Frequent small slides produce irregular hillslopes, on which steep toes and head scarps persist until being cleared by infrequent large slides. These steep segments are observed on hillslopes in high-relief landscapes and have been interpreted as evidence for increases in tectonic or climatic process rates. In certain cases, they may instead reflect normal hillslope evolution by landsliding.

Liquid Argon TPC Signal Formation, Signal Processing and Hit Reconstruction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baller, Bruce

2017-03-11

This document describes the early stage of the reconstruction chain that was developed for the ArgoNeuT and MicroBooNE experiments at Fermilab. These experiments study accelerator neutrino interactions that occur in a Liquid Argon Time Projection Chamber. Reconstructing the properties of particles produced in these interactions requires knowledge of the micro-physics processes that affect the creation and transport of ionization electrons to the readout system. A wire signal deconvolution technique was developed to convert wire signals to a standard form for hit reconstruction, to remove artifacts in the electronics chain and to remove coherent noise.

Plasma heating for containerless and microgravity materials processing

NASA Technical Reports Server (NTRS)

Leung, Emily W. (Inventor); Man, Kin F. (Inventor)

1994-01-01

A method for plasma heating of levitated samples to be used in containerless microgravity processing is disclosed. A sample is levitated by electrostatic, electromagnetic, aerodynamic, or acoustic systems, as is appropriate for the physical properties of the particular sample. The sample is heated by a plasma torch at atmospheric pressure. A ground plate is provided to help direct the plasma towards the sample. In addition, Helmholtz coils are provided to produce a magnetic field that can be used to spiral the plasma around the sample. The plasma heating system is oriented such that it does not interfere with the levitation system.

Interplay of Physical Mechanisms and Biofilm Processes: Review of Microfluidic Methods

PubMed Central

Karimi, A.; Karig, D.; Kumar, A.; Ardekani, A. M.

2014-01-01

Bacteria in natural and artificial environments often reside in self-organized, integrated communities known as biofilms. Biofilms are highly structured entities consisting of bacterial cells embedded in a matrix of self-produced extracellular polymeric substances (EPS). The EPS matrix acts like a biological ‘glue’ enabling microbes to adhere to and colonize a wide range of surfaces. Once integrated into biofilms, bacterial cells can withstand various forms of stress such as antibiotics, hydrodynamic shear and other environmental challenges. Because of this, biofilms of pathogenic bacteria can be a significant health hazard often leading to recurrent infections. Biofilms can also lead to clogging and material degradation; on the other hand they are an integral part of various environmental processes such as carbon sequestration and nitrogen cycles. There are several determinants of biofilm morphology and dynamics, including the genotypic and phenotypic states of constituent cells and various environmental conditions. Here, we present an overview of the role of relevant physical processes in biofilm formation, including propulsion mechanisms, hydrodynamic effects, and transport of quorum sensing signals. We also provide a survey of microfluidic techniques utilized to unravel the associated physical mechanisms. Further, we discuss the future research areas for exploring new ways to extend the scope of the microfluidic approach in biofilm studies. PMID:25385289

Unified Models of Turbulence and Nonlinear Wave Evolution in the Extended Solar Corona and Solar Wind

NASA Technical Reports Server (NTRS)

Cranmer, Steven R.; Wagner, William (Technical Monitor)

2004-01-01

The PI (Cranmer) and Co-I (A. van Ballegooijen) made substantial progress toward the goal of producing a unified model of the basic physical processes responsible for solar wind acceleration. The approach outlined in the original proposal comprised two complementary pieces: (1) to further investigate individual physical processes under realistic coronal and solar wind conditions, and (2) to extract the dominant physical effects from simulations and apply them to a 1D model of plasma heating and acceleration. The accomplishments in Year 2 are divided into these two categories: 1a. Focused Study of Kinetic Magnetohydrodynamic (MHD) Turbulence. lb. Focused Study of Non - WKB Alfven Wave Rejection. and 2. The Unified Model Code. We have continued the development of the computational model of a time-study open flux tube in the extended corona. The proton-electron Monte Carlo model is being tested, and collisionless wave-particle interactions are being included. In order to better understand how to easily incorporate various kinds of wave-particle processes into the code, the PI performed a detailed study of the so-called "Ito Calculus", i.e., the mathematical theory of how to update the positions of particles in a probabilistic manner when their motions are governed by diffusion in velocity space.

Photoassisted physical vapor epitaxial growth of semiconductors: a review of light-induced modifications to growth processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alberi, Kirstin; Scarpulla, Michael A.

Herein, we review the remarkable range of modifications to materials properties associated with photoexcitation of the growth surface during physical vapor epitaxy of semiconductors. We concentrate on mechanisms producing measureable, utilizable changes in crystalline perfection, phase, composition, doping, and defect distribution. We outline the relevant physics of different mechanisms, concentrating on those yielding effects orthogonal to the primary growth variables of temperature and atomic or molecular fluxes and document the phenomenological effects reported. Based on experimental observations from a range of semiconductor systems and growth conditions, the primary effects include enhanced anion desorption, molecular dissociation, increased doping efficiency, modification tomore » defect populations and improvements to the crystalline quality of epilayers grown at low temperatures. Future research directions and technological applications are also discussed.« less

HEP Community White Paper on Software Trigger and Event Reconstruction: Executive Summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Albrecht, Johannes; et al.

Realizing the physics programs of the planned and upgraded high-energy physics (HEP) experiments over the next 10 years will require the HEP community to address a number of challenges in the area of software and computing. For this reason, the HEP software community has engaged in a planning process over the past two years, with the objective of identifying and prioritizing the research and development required to enable the next generation of HEP detectors to fulfill their full physics potential. The aim is to produce a Community White Paper which will describe the community strategy and a roadmap for softwaremore » and computing research and development in HEP for the 2020s. The topics of event reconstruction and software triggers were considered by a joint working group and are summarized together in this document.« less

HEP Community White Paper on Software Trigger and Event Reconstruction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Albrecht, Johannes; et al.

Realizing the physics programs of the planned and upgraded high-energy physics (HEP) experiments over the next 10 years will require the HEP community to address a number of challenges in the area of software and computing. For this reason, the HEP software community has engaged in a planning process over the past two years, with the objective of identifying and prioritizing the research and development required to enable the next generation of HEP detectors to fulfill their full physics potential. The aim is to produce a Community White Paper which will describe the community strategy and a roadmap for softwaremore » and computing research and development in HEP for the 2020s. The topics of event reconstruction and software triggers were considered by a joint working group and are summarized together in this document.« less

Photoassisted physical vapor epitaxial growth of semiconductors: a review of light-induced modifications to growth processes

DOE PAGES

Alberi, Kirstin; Scarpulla, Michael A.

2017-11-22

Herein, we review the remarkable range of modifications to materials properties associated with photoexcitation of the growth surface during physical vapor epitaxy of semiconductors. We concentrate on mechanisms producing measureable, utilizable changes in crystalline perfection, phase, composition, doping, and defect distribution. We outline the relevant physics of different mechanisms, concentrating on those yielding effects orthogonal to the primary growth variables of temperature and atomic or molecular fluxes and document the phenomenological effects reported. Based on experimental observations from a range of semiconductor systems and growth conditions, the primary effects include enhanced anion desorption, molecular dissociation, increased doping efficiency, modification tomore » defect populations and improvements to the crystalline quality of epilayers grown at low temperatures. Future research directions and technological applications are also discussed.« less

Silver removal from aqueous solution by biochar produced from biosolids via microwave pyrolysis.

PubMed

Antunes, Elsa; Jacob, Mohan V; Brodie, Graham; Schneider, Philip A

2017-12-01

The contamination of water with silver has increased due to the widespread applications of products with silver employed as antimicrobial agent. Adsorption is a cost-effective method for silver removal from aqueous solution. In this study biochar, produced from the microwave assisted pyrolysis of biosolids, was used for silver removal from an aqueous solution. The adsorption kinetics, isotherms and thermodynamics were investigated to better understand the silver removal process by biochar. X-ray diffraction results demonstrated that silver removal was a combination two consecutive mechanisms, reduction and physical adsorption. The Langmuir model fitted the experimental data well, showing that silver removal was predominantly a surface mechanism. The thermodynamic investigation demonstrated that silver removal by biochar was an exothermic process. The final nanocomposite Ag-biochar (biochar plus silver) was used for methylene blue adsorption and photodegradation. This study showed the potential of using biochar produced from biosolids for silver removal as a promising solution to mitigate water pollution and an environmentally sustainable approach for biosolids management and re-use. Copyright © 2017 Elsevier Ltd. All rights reserved.

Trojan particles: Large porous carriers of nanoparticles for drug delivery

PubMed Central

Tsapis, N.; Bennett, D.; Jackson, B.; Weitz, D. A.; Edwards, D. A.

2002-01-01

We have combined the drug release and delivery potential of nanoparticle (NP) systems with the ease of flow, processing, and aerosolization potential of large porous particle (LPP) systems by spray drying solutions of polymeric and nonpolymeric NPs into extremely thin-walled macroscale structures. These hybrid LPPs exhibit much better flow and aerosolization properties than the NPs; yet, unlike the LPPs, which dissolve in physiological conditions to produce molecular constituents, the hybrid LPPs dissolve to produce NPs, with the drug release and delivery advantages associated with NP delivery systems. Formation of the large porous NP (LPNP) aggregates occurs via a spray-drying process that ensures the drying time of the sprayed droplet is sufficiently shorter than the characteristic time for redistribution of NPs by diffusion within the drying droplet, implying a local Peclet number much greater than unity. Additional control over LPNPs physical characteristics is achieved by adding other components to the spray-dried solutions, including sugars, lipids, polymers, and proteins. The ability to produce LPNPs appears to be largely independent of molecular component type as well as the size or chemical nature of the NPs. PMID:12200546

Development of a New Ferrous Aluminosilicate Refractory Material for Investment Casting of Aluminum Alloys

NASA Astrophysics Data System (ADS)

Yuan, Chen; Jones, Sam; Blackburn, Stuart

2012-12-01

Investment casting is a time-consuming, labour intensive process, which produces complex, high value-added components for a variety of specialised industries. Current environmental and economic pressures have resulted in a need for the industry to improve current casting quality, reduce manufacturing costs and explore new markets for the process. Alumino-silicate based refractories are commonly used as both filler and stucco materials for ceramic shell production. A new ceramic material, norite, is now being produced based on ferrous aluminosilicate chemistry, having many potential advantages when used for the production of shell molds for casting aluminum alloy. This paper details the results of a direct comparison made between the properties of a ceramic shell system produced with norite refractories and a typical standard refractory shell system commonly used in casting industry. A range of mechanical and physical properties of the systems was measured, and a full-scale industrial casting trial was also carried out. The unique properties of the norite shell system make it a promising alternative for casting aluminum based alloys in the investment foundry.

Preparation and Photocatalytic Activity of Potassium-Incorporated Titanium Oxide Nanostructures Produced by the Wet Corrosion Process Using Various Titanium Alloys

PubMed Central

Lee, So Yoon; Lee, Choong Hyun; Kim, Do Yun; Locquet, Jean-Pierre; Seo, Jin Won

2015-01-01

Nanostructured potassium-incorporated Ti-based oxides have attracted much attention because the incorporated potassium can influence their structural and physico-chemical properties. With the aim of tuning the structural and physical properties, we have demonstrated the wet corrosion process (WCP) as a simple method for nanostructure fabrication using various Ti-based materials, namely Ti–6Al–4V alloy (TAV), Ti–Ni (TN) alloy and pure Ti, which have 90%, 50% and 100% initial Ti content, respectively. We have systematically investigated the relationship between the Ti content in the initial metal and the precise condition of WCP to control the structural and physical properties of the resulting nanostructures. The WCP treatment involved various concentrations of KOH solutions. The precise conditions for producing K-incorporated nanostructured titanium oxide films (nTOFs) were strongly dependent on the Ti content of the initial metal. Ti and TAV yielded one-dimensional nanowires of K-incorporated nTOFs after treatment with 10 mol/L-KOH solution, whereas TN required a higher concentration (20 mol/L-KOH solution) to produce comparable nanostructures. The obtained nanostructures revealed a blue-shift in UV absorption spectra due to the quantum confinement effects. A significant enhancement of the photocatalytic activity was observed via the chromomeric change and the intermediate formation of methylene blue molecules under UV irradiation. This study demonstrates the WCP as a simple, versatile and scalable method for the production of nanostructured K-incorporated nTOFs to be used as high-performance photocatalysts for environmental and energy applications. PMID:28347071

The pro-life argument from substantial identity and the pro-choice argument from asymmetric value: a reply to Patrick Lee.

PubMed

Reiman, Jeffrey

2007-07-01

Lee claims that foetuses and adult humans are phases of the same identical substance, and thus have the same moral status because: first, foetuses and adults are the same physical organism, and second, the development from foetus to adult is quantitative and thus not a change of substance. Versus the first argument, I contend that the fact that foetuses and adults are the same physical organism implies only that they are the same thing but not the same substance, much as living adults and their corpses are the same thing (same body) but not the same substance. Against Lee's second argument, I contend that Lee confuses the nature of a process with the nature of its result. A process of quantitative change can produce a change in substance. Lee also fails to show that foetuses are rational and thus have all the essential properties of adults, as required for them to be the same substance. Against the pro-choice argument from asymmetric value (that only the fact that a human has become conscious of its life and begun to count on its continuing can explain human life's asymmetric moral value, i.e. that it is vastly worse to kill a human than not to produce one), Lee claims that foetus's lives are asymmetrically valuable to them before consciousness. This leads to counterintuitive outcomes, and it confuses the goodness of life (a symmetric value that cannot account for why it is worse to kill a human than not produce one) with asymmetric value.

EDITORIAL: Fracture: from the atomic to the geophysical scale Fracture: from the atomic to the geophysical scale

NASA Astrophysics Data System (ADS)

Bouchaud, Elisabeth; Soukiassian, Patrick

2009-11-01

Although fracture is a very common experience in every day life, it still harbours many unanswered questions. New avenues of investigation arise concerning the basic mechanisms leading to deformation and failure in heterogeneous materials, particularly in non-metals. The processes involved are even more complex when plasticity, thermal fluctuations or chemical interactions between the material and its environment introduce a specific time scale. Sub-critical failure, which may be reached at unexpectedly low loads, is particularly important for silicate glasses. Another source of complications originates from dynamic fracture, when loading rates become so high that the acoustic waves produced by the crack interact with the material heterogeneities, in turn producing new waves that modify the propagation. Recent progress in experimental techniques, allowing one to test and probe materials at sufficiently small length or time scales or in three dimensions, has led to a quantitative understanding of the physical processes involved. In parallel, simulations have also progressed, by extending the time and length scales they are able to reach, and thus attaining experimentally accessible conditions. However, one central question remains the inclusion of these basic mechanisms into a statistical description. This is not an easy task, mostly because of the strong stress gradients present at the tip of a crack, and because the averaging of fracture properties over a heterogeneous material, containing more or less brittle phases, requires rare event statistics. Substantial progress has been made in models and simulations based on accurate experiments. From these models, scaling laws have been derived, linking the behaviour at a micro- or even nano-scale to the macroscopic and even to geophysical scales. The reviews in this Cluster Issue of Journal of Physics D: Applied Physics cover several of these important topics, including the physical processes in fracture mechanisms, the sub-critical failure issue, the dynamical fracture propagation, and the scaling laws from the micro- to the geophysical scales. Achievements and progress are reported, and the many open questions are discussed, which should provide a sound basis for present and future prospects.

Intensity Maps Production Using Real-Time Joint Streaming Data Processing From Social and Physical Sensors

NASA Astrophysics Data System (ADS)

Kropivnitskaya, Y. Y.; Tiampo, K. F.; Qin, J.; Bauer, M.

2015-12-01

Intensity is one of the most useful measures of earthquake hazard, as it quantifies the strength of shaking produced at a given distance from the epicenter. Today, there are several data sources that could be used to determine intensity level which can be divided into two main categories. The first category is represented by social data sources, in which the intensity values are collected by interviewing people who experienced the earthquake-induced shaking. In this case, specially developed questionnaires can be used in addition to personal observations published on social networks such as Twitter. These observations are assigned to the appropriate intensity level by correlating specific details and descriptions to the Modified Mercalli Scale. The second category of data sources is represented by observations from different physical sensors installed with the specific purpose of obtaining an instrumentally-derived intensity level. These are usually based on a regression of recorded peak acceleration and/or velocity amplitudes. This approach relates the recorded ground motions to the expected felt and damage distribution through empirical relationships. The goal of this work is to implement and evaluate streaming data processing separately and jointly from both social and physical sensors in order to produce near real-time intensity maps and compare and analyze their quality and evolution through 10-minute time intervals immediately following an earthquake. Results are shown for the case study of the M6.0 2014 South Napa, CA earthquake that occurred on August 24, 2014. The using of innovative streaming and pipelining computing paradigms through IBM InfoSphere Streams platform made it possible to read input data in real-time for low-latency computing of combined intensity level and production of combined intensity maps in near-real time. The results compare three types of intensity maps created based on physical, social and combined data sources. Here we correlate the count and density of Tweets with intensity level and show the importance of processing combined data sources at the earliest time stages after earthquake happens. This method can supplement existing approaches of intensity level detection, especially in the regions with high number of Twitter users and low density of seismic networks.

Impact Flash Physics: Modeling and Comparisons With Experimental Results

NASA Astrophysics Data System (ADS)

Rainey, E.; Stickle, A. M.; Ernst, C. M.; Schultz, P. H.; Mehta, N. L.; Brown, R. C.; Swaminathan, P. K.; Michaelis, C. H.; Erlandson, R. E.

2015-12-01

Hypervelocity impacts frequently generate an observable "flash" of light with two components: a short-duration spike due to emissions from vaporized material, and a long-duration peak due to thermal emissions from expanding hot debris. The intensity and duration of these peaks depend on the impact velocity, angle, and the target and projectile mass and composition. Thus remote sensing measurements of planetary impact flashes have the potential to constrain the properties of impacting meteors and improve our understanding of impact flux and cratering processes. Interpreting impact flash measurements requires a thorough understanding of how flash characteristics correlate with impact conditions. Because planetary-scale impacts cannot be replicated in the laboratory, numerical simulations are needed to provide this insight for the solar system. Computational hydrocodes can produce detailed simulations of the impact process, but they lack the radiation physics required to model the optical flash. The Johns Hopkins University Applied Physics Laboratory (APL) developed a model to calculate the optical signature from the hot debris cloud produced by an impact. While the phenomenology of the optical signature is understood, the details required to accurately model it are complicated by uncertainties in material and optical properties and the simplifications required to numerically model radiation from large-scale impacts. Comparisons with laboratory impact experiments allow us to validate our approach and to draw insight regarding processes that occur at all scales in impact events, such as melt generation. We used Sandia National Lab's CTH shock physics hydrocode along with the optical signature model developed at APL to compare with a series of laboratory experiments conducted at the NASA Ames Vertical Gun Range. The experiments used Pyrex projectiles to impact pumice powder targets with velocities ranging from 1 to 6 km/s at angles of 30 and 90 degrees with respect to horizontal. High-speed radiometer measurements were made of the time-dependent impact flash at wavelengths of 350-1100 nm. We will present comparisons between these measurements and the output of APL's model. The results of this validation allow us to determine basic relationships between observed optical signatures and impact conditions.

Infinite efficiency of the collisional Penrose process: Can a overspinning Kerr geometry be the source of ultrahigh-energy cosmic rays and neutrinos?

NASA Astrophysics Data System (ADS)

Patil, Mandar; Harada, Tomohiro; Nakao, Ken-ichi; Joshi, Pankaj S.; Kimura, Masashi

2016-05-01

The origin of the ultrahigh-energy particles we receive on Earth from outer space such as EeV cosmic rays and PeV neutrinos remains an enigma. All mechanisms known to us currently make use of electromagnetic interaction to accelerate charged particles. In this paper, we propose a mechanism exclusively based on gravity rather than electromagnetic interaction. We show that it is possible to generate ultrahigh-energy particles starting from particles with moderate energies using the collisional Penrose process in an overspinning Kerr spacetime transcending the Kerr bound only by an infinitesimal amount, i.e., with the Kerr parameter a =M (1 +ɛ ) , where we take the limit ɛ →0+. We consider two massive particles starting from rest at infinity that collide at r =M with divergent center-of-mass energy and produce two massless particles. We show that massless particles produced in the collision can escape to infinity with the ultrahigh energies exploiting the collisional Penrose process with the divergent efficiency η ˜1 /√{ɛ }→∞ . Assuming the isotropic emission of massless particles in the center-of-mass frame of the colliding particles, we show that half of the particles created in the collisions escape to infinity with the divergent energies, while the proportion of particles that reach infinity with finite energy is minuscule. To a distant observer, ultrahigh-energy particles appear to originate from a bright spot which is at the angular location ξ ˜2 M /robs with respect to the singularity on the side which is rotating toward the observer. We compute the spectrum of the high-energy massless particles and show that anisotropy in the emission in the center-of-mass frame leaves a distinct signature on its shape. Since the anisotropy is dictated by the differential cross section of the underlying particle physics process, the observation of the spectrum can constrain the particle physics model and serve as a unique probe into fundamental physics at ultrahigh energies at which particles collide. Thus, the existence of the near-extremal overspinning Kerr geometry in the Universe, either as a transient or permanent configuration, would have deep implications on astrophysics as well as fundamental particle physics.

The Impact of NSF-funded Physics Education Research at the University of Washington

NASA Astrophysics Data System (ADS)

Heron, Paula

2015-03-01

It is now well known that many students who complete introductory physics courses are unable to apply fundamental concepts in situations that involve qualitative reasoning. Systematic investigations have helped researchers understand why so many students fail to develop robust and coherent conceptual frameworks, and have led to the development of new teaching practices and materials that are far more effective than conventional ones. The Physics Education Group at the University of Washington has played a leading role in raising awareness of the need to improve instruction, and in supporting physics faculty in their efforts to do so. With support from the National Science Foundation, the group has helped build a research base that instructors can draw on, and has produced practical, flexible instructional materials that promote deeper learning in physics classrooms. Both ``Tutorials in Introductory Physics'' (Pearson, 2002) and ``Physics by Inquiry'' (Wiley, 1996) have been developed in an iterative process in which ongoing assessment of student learning plays an integral role. These materials have had a widespread and significant impact on physics teaching and on student learning from kindergarten through graduate school. In this talk I will describe the role of research in curriculum development, and speculate on the next generation of tools and resources to support physics teaching and learning.

Bacteriophage T4 capsid packaging and unpackaging of DNA and proteins.

PubMed

Mullaney, Julienne M; Black, Lindsay W

2014-01-01

Bacteriophage T4 has proven itself readily amenable to phage-based DNA and protein packaging, expression, and display systems due to its physical resiliency and genomic flexibility. As a large dsDNA phage with dispensable internal proteins and dispensable outer capsid proteins it can be adapted to package both DNA and proteins of interest within the capsid and to display peptides and proteins externally on the capsid. A single 170 kb linear DNA, or single or multiple copies of shorter linear DNAs, of any sequence can be packaged by the large terminase subunit in vitro into protein-containing proheads and give full or partially full capsids. The prohead receptacles for DNA packaging can also display peptides or full-length proteins from capsid display proteins HOC and SOC. Our laboratory has also developed a protein expression, packaging, and processing (PEPP) system which we have found to have advantages over mammalian and bacterial cell systems, including high yield, increased stability, and simplified downstream processing. Proteins that we have produced by the phage PEPP platform include human HIV-1 protease, micrococcal endonuclease from Staphylococcus aureus, restriction endonuclease EcoRI, luciferase, human granulocyte colony stimulating factor (GCSF), green fluorescent protein (GFP), and the 99 amino acid C-terminus of amyloid precursor protein (APP). Difficult to produce proteins that are toxic in mammalian protein expression systems are easily produced, packaged, and processed with the PEPP platform. APP is one example of such a highly refractory protein that has been produced successfully. The methods below describe the procedures for in vitro packaging of proheads with DNA and for producing recombinant T4 phage that carry a gene of interest in the phage genome and produce and internally package the corresponding protein of interest.

Functional Basis for Efficient Physical Layer Classical Control in Quantum Processors

NASA Astrophysics Data System (ADS)

Ball, Harrison; Nguyen, Trung; Leong, Philip H. W.; Biercuk, Michael J.

2016-12-01

The rapid progress seen in the development of quantum-coherent devices for information processing has motivated serious consideration of quantum computer architecture and organization. One topic which remains open for investigation and optimization relates to the design of the classical-quantum interface, where control operations on individual qubits are applied according to higher-level algorithms; accommodating competing demands on performance and scalability remains a major outstanding challenge. In this work, we present a resource-efficient, scalable framework for the implementation of embedded physical layer classical controllers for quantum-information systems. Design drivers and key functionalities are introduced, leading to the selection of Walsh functions as an effective functional basis for both programing and controller hardware implementation. This approach leverages the simplicity of real-time Walsh-function generation in classical digital hardware, and the fact that a wide variety of physical layer controls, such as dynamic error suppression, are known to fall within the Walsh family. We experimentally implement a real-time field-programmable-gate-array-based Walsh controller producing Walsh timing signals and Walsh-synthesized analog waveforms appropriate for critical tasks in error-resistant quantum control and noise characterization. These demonstrations represent the first step towards a unified framework for the realization of physical layer controls compatible with large-scale quantum-information processing.

Initiation of non-tropical thunderstorms by solar activity

NASA Technical Reports Server (NTRS)

Herman, J. R.; Goldberg, R. A.

1976-01-01

Correlative evidence accumulating since 1926 suggests that there must be some physical coupling mechanism between solar activity and thunderstorm occurrence in middle to high latitudes. Such a link may be provided by alteration of atmospheric electric parameters through the combined influence of high-energy solar protons and decreased cosmic ray intensities, both of which are associated with active solar events. The protons produce excess ionization near and above 20km, while the Forbush decreases a lowered conductivity and enhanced fair-weather atmospheric electric field below that altitude. Consequent effects ultimately lead to a charge distribution similar to that found in thunderclouds, and then other cloud physics processes take over to generate the intense electric fields required for lightning discharge.

Coal Gasification - section in Kirk-Othmer Concise Encyclopedia of Chemical Technology, 5th Edition, 2-vol. set, July 2007, ISBN 978-0-470-04748-4, pp. 580-587

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shadle, L.J.; Berry, D.A.; Syamlal, Madhava

2007-07-01

Coal gasification is the process of reacting coal with oxygen, steam, and carbon dioxide to form a product gas containing hydrogen and carbon monoxide. Gasification is essentially incomplete combustion. The chemical and physical processes are quite similar, the main difference being the nature of the final products. From a processing point of view the main operating difference is that gasification consumes heat evolved during combustion. Under the reducing environment of gasification the sulfur in the coal is released as hydrogen sulfide rather than sulfur dioxide and the coal's nitrogen is converted mostly to ammonia rather than nitrogen oxides. These reducedmore » forms of sulfur and nitrogen are easily isolated, captured, and utilized, and thus gasification is a clean coal technology with better environmental performance than coal combustion. Depending on the type of gasifier and the operating conditions, gasification can be used to produce a fuel gas suitable for any number of applications. A low heating value fuel gas is produced from an air blown gasifier for use as an industrial fuel and for power production. A medium heating value fuel gas is produced from enriched oxygen blown gasification for use as a synthesis gas in the production of chemicals such as ammonia, methanol, and transportation fuels. A high heating value gas can be produced from shifting the medium heating value product gas over catalysts to produce a substitute or synthetic natural gas (SNG).« less

Effects of Exercise Training and Social Environment on Stress Resilience in Male and Female Long-Evans Rats

DTIC Science & Technology

2010-03-15

1976) described the stress response as a process, named the general adaptation syndrome (GAS). The GAS is a non-specific stress response that...individual attempts to return to normal functioning. The exhaustion phase is also known as burnout , and occurs when the individual no longer has...including cardiovascular disease, obesity, diabetes, and metabolic syndrome . Physical activity is defined as any bodily movement produced by skeletal

Laboratory Evaluation of Remediation Alternatives for U.S. Coast Guard Small Arms Firing Ranges

DTIC Science & Technology

1999-11-01

S) is an immobilization process that involves the mixing of a contaminated soil with a binder material to enhance the physical and chemical...samples were shipped to WES for laboratory analysis. Phase III: Homogenization of the Bulk Samples. Each of the bulk samples was separately mixed to...produce uniform samples for testing. These mixed bulk soil samples were analyzed for metal content. Phase IV: Characterization of the Bulk Soils

Mathematics and Physics Studies - Multi-Project Support

DTIC Science & Technology

1989-09-02

measurements). A quaternion form is used to represent any finite rotation of a rigid body as a rotation through some angle about a fixed axis (Euler’s...many - contractual issues. Drs. Edmond Murad (GL/PHK) and Roger Van Tassel (GL/OPB) provided important suggestions and feedback on the data processing...Orbital Maneuvering System (OMS) and the Reaction Control System (RCS) resemble plumes produced by targets/events of interest. Measurements from the IBSS

The Physical and Chemical Characterization of Ten Military Turbine Engine Lubricants.

DTIC Science & Technology

1979-09-01

fractions have been further evaluated by chemical hydrolysis and derivitized to determine the exact composition of the parent acid and alcohol components...separates the ester compounds into their original alcohol and acid components, This cleavage process produces the acid as a water—soluble salt which...allows the extraction and recovery of the alcohol from the acid salt by organic solvent extraction. In turn, the acid salt can be converted to the free

Solution-processing of chalcogenide materials for device applications

NASA Astrophysics Data System (ADS)

Zha, Yunlai

Chalcogenide glasses are well-known for their desirable optical properties, which have enabled many infrared applications in the fields of photonics, medicine, environmental sensing and security. Conventional deposition methods such as thermal evaporation, chemical vapor deposition, sputtering or pulse laser deposition are efficient for fabricating structures on flat surfaces. However, they have limitations in deposition on curved surfaces, deposition of thick layers and component integration. In these cases, solution-based methods, which involve the dissolution of chalcogenide glasses and processing as a liquid, become a better choice for their flexibility. After proper treatment, the associated structures can have similar optical, chemical and physical properties to the bulk. This thesis presents an in-depth study of solution-processing chalcogenide glasses, starting from the "solution state" to the "film state" and the "structure state". Firstly, chalcogenide dissolution is studied to reveal the mechanisms at molecular level and build a foundation for material processing. Dissolution processes for various chalcogenide solvent pairs are reviewed and compared. Secondly, thermal processing, in the context of high temperature annealing, is explained along with the chemical and physical properties of the annealed films. Another focus is on nanopore formation in propylamine-processed arsenic sulfide films. Pore density changes with respect to annealing temperatures and durations are characterized. Base on a proposed vacancy coalescence theory, we have identified new dissolution strategies and achieved the breakthrough of pore-free film deposition. Thirdly, several solution methods developed along with the associated photonic structures are demonstrated. The first example is "spin-coating and lamination", which produces thick (over 10 mum) chalcogenide structures. Both homogeneous thick chalcogenide structures and heterogeneous layers of different chalcogenide glasses or metals can be fabricated. Second, "micro-molding in capillaries" (MIMIC) and "micro-transfer molding" (muTM) methods are introduced for fabricating waveguides on flat and curved surfaces. The flexibility of the solution process allows waveguides to be patterned, for the first time, on a curved surface. Third, "micro channel filling" is demonstrated to produce the lowest loss among solution-processed chalcogenide waveguides. These results contribute to the advancement of chalcogenide processing technologies and help move closer towards the ultimate goal of fabricating reliable IR sensors.

Alternative Fuels Data Center

Science.gov Websites

format to determine RINs for each physical gallon of renewable fuel produced in or imported into the -character number assigned to each physical gallon of renewable fuel produced or imported. Obligated parties Transaction System (EMTS). The RIN is attached to the physical gallon of renewable fuel as it is transferred

Impact of biochar produced from post-harvest residue on the adsorption behavior of diesel oil on loess soil.

PubMed

Jiang, Yu Feng; Sun, Hang; Yves, Uwamungu J; Li, Hong; Hu, Xue Fei

2016-02-01

The primary objective of this study was to investigate the effect of biochar, produced from wheat residue at different temperatures, on the adsorption of diesel oil by loess soil. Kinetic and equilibrium data were processed to understand the adsorption mechanism of diesel by biochar-affected loess soil; dynamic and thermodynamic adsorption experiments were conducted to characterize this adsorption. The surface features and chemical structure of biochar, modified at varying pyrolytic temperatures, were investigated using surface scanning electron microscopy and Fourier transform infrared analysis. The kinetic data showed that the adsorption of diesel oil onto loess soil could be described by a pseudo-second-order kinetic model, with the rate-controlling step being intraparticle diffusion. However, in the presence of biochar, boundary layer control and intraparticle diffusion were both involved in the adsorption. Besides, the adsorption equilibrium data were well described by the Freundlich isothermal model. The saturated adsorption capacity weakened as temperature increased, suggesting a spontaneous exothermic process. Thermodynamic parameter analysis showed that adsorption was mainly a physical process and was enhanced by chemical adsorption. The adsorption capacity of loess soil for diesel oil was weakened with increasing pH. The biochar produced by pyrolytic wheat residue increased the adsorption behavior of petroleum pollutants in loess soil.

Refining and blending of aviation turbine fuels.

PubMed

White, R D

1999-02-01

Aviation turbine fuels (jet fuels) are similar to other petroleum products that have a boiling range of approximately 300F to 550F. Kerosene and No.1 grades of fuel oil, diesel fuel, and gas turbine oil share many similar physical and chemical properties with jet fuel. The similarity among these products should allow toxicology data on one material to be extrapolated to the others. Refineries in the USA manufacture jet fuel to meet industry standard specifications. Civilian aircraft primarily use Jet A or Jet A-1 fuel as defined by ASTM D 1655. Military aircraft use JP-5 or JP-8 fuel as defined by MIL-T-5624R or MIL-T-83133D respectively. The freezing point and flash point are the principle differences between the finished fuels. Common refinery processes that produce jet fuel include distillation, caustic treatment, hydrotreating, and hydrocracking. Each of these refining processes may be the final step to produce jet fuel. Sometimes blending of two or more of these refinery process streams are needed to produce jet fuel that meets the desired specifications. Chemical additives allowed for use in jet fuel are also defined in the product specifications. In many cases, the customer rather than the refinery will put additives into the fuel to meet their specific storage or flight condition requirements.

Low-viscosity hydroxypropylcellulose (HPC) grades SL and SSL: versatile pharmaceutical polymers for dissolution enhancement, controlled release, and pharmaceutical processing.

PubMed

Sarode, Ashish; Wang, Peng; Cote, Catherine; Worthen, David R

2013-03-01

Hydroxypropylcellulose (HPC)-SL and -SSL, low-viscosity hydroxypropylcellulose polymers, are versatile pharmaceutical excipients. The utility of HPC polymers was assessed for both dissolution enhancement and sustained release of pharmaceutical drugs using various processing techniques. The BCS class II drugs carbamazepine (CBZ), hydrochlorthiazide, and phenytoin (PHT) were hot melt mixed (HMM) with various polymers. PHT formulations produced by solvent evaporation (SE) and ball milling (BM) were prepared using HPC-SSL. HMM formulations of BCS class I chlorpheniramine maleate (CPM) were prepared using HPC-SL and -SSL. These solid dispersions (SDs) manufactured using different processes were evaluated for amorphous transformation and dissolution characteristics. Drug degradation because of HMM processing was also assessed. Amorphous conversion using HMM could be achieved only for relatively low-melting CBZ and CPM. SE and BM did not produce amorphous SDs of PHT using HPC-SSL. Chemical stability of all the drugs was maintained using HPC during the HMM process. Dissolution enhancement was observed in HPC-based HMMs and compared well to other polymers. The dissolution enhancement of PHT was in the order of SE>BM>HMM>physical mixtures, as compared to the pure drug, perhaps due to more intimate mixing that occurred during SE and BM than in HMM. Dissolution of CPM could be significantly sustained in simulated gastric and intestinal fluids using HPC polymers. These studies revealed that low-viscosity HPC-SL and -SSL can be employed to produce chemically stable SDs of poorly as well as highly water-soluble drugs using various pharmaceutical processes in order to control drug dissolution.

Production of carbon monoxide-free hydrogen and helium from a high-purity source

DOEpatents

Golden, Timothy Christopher [Allentown, PA; Farris, Thomas Stephen [Bethlehem, PA

2008-11-18

The invention provides vacuum swing adsorption processes that produce an essentially carbon monoxide-free hydrogen or helium gas stream from, respectively, a high-purity (e.g., pipeline grade) hydrogen or helium gas stream using one or two adsorber beds. By using physical adsorbents with high heats of nitrogen adsorption, intermediate heats of carbon monoxide adsorption, and low heats of hydrogen and helium adsorption, and by using vacuum purging and high feed stream pressures (e.g., pressures of as high as around 1,000 bar), pipeline grade hydrogen or helium can purified to produce essentially carbon monoxide -free hydrogen and helium, or carbon monoxide, nitrogen, and methane-free hydrogen and helium.

Neutrino spectroscopy can probe the dark matter content in the Sun.

PubMed

Lopes, Ilídio; Silk, Joseph

2010-10-22

After being gravitationally captured, low-mass cold dark-matter particles (mass range from 5 to ~50 × 10(9) electron volts) are thought to drift to the center of the Sun and affect its internal structure. Solar neutrinos provide a way to probe the physical processes occurring in the Sun's core. Solar neutrino spectroscopy, in particular, is expected to measure the neutrino fluxes produced in nuclear reactions in the Sun. Here, we show how the presence of dark-matter particles inside the Sun will produce unique neutrino flux distributions in (7)Be-ν and (8)B-ν, as well as (13)N-ν, (15)O-ν, and (17)F-ν.

Suprathermal electrons in kJ-laser produced plasmas: M- shell resolved high-resolution x-ray spectroscopic study of transient matter evolution

NASA Astrophysics Data System (ADS)

Condamine, F. P.; Šmíd, M.; Renner, O.; Dozières, M.; Thais, F.; Angelo, P.; Bobin, J.-L.; Rosmej, F. B.

2016-05-01

Hot electrons are of key importance to understand many physical processes in plasma physics. They impact strongly on atomic physics as almost all radiative properties are seriously modified. X-ray spectroscopy is of particular interest due to reduced photoabsorption in dense matter. We report on a study of the copper Kα X-ray emission conducted at the ns, kJ laser facility PALS, Prague, Czech Republic. Thin copper foils have been irradiated with 1ω pulses. Two spherically bent quartz Bragg crystal spectrometers with high spectral and spatial resolution have been set up simultaneously to achieve a high level of confidence in the spectral distribution. In particular, an emission on the red wing of the Kα2 transition (λ = 1.5444 Å) could be identified with complex atomic structure calculations. We discuss possible implications for the analysis of non-equilibrium phenomena and present first atomic physics simulations.

A MEDL Collection Showcase: A Collection of Hands-on Physical Analog Models and Demonstrations From the Department of Geosciences MEDL at Virginia Tech

NASA Astrophysics Data System (ADS)

Glesener, G. B.

2017-12-01

The Geosciences Modeling and Educational Demonstrations Laboratory (MEDL) will present a suite of hands-on physical analog models from our curriculum materials collection used to teach about a wide range of geoscience processes. Many of the models will be equipped with Vernier data collection sensors, which visitors will be encouraged to explore on-site. Our goal is to spark interest and discussion around the affordances of these kinds of curriculum materials. Important topics to discuss will include: (1) How can having a collection of hands-on physical analog models be used to effectively produce successful broader impacts activities for research proposals? (2) What kinds of learning outcomes have instructors observed when teaching about temporally and spatially challenging concepts using physical analog models? (3) What does it take for an institution to develop their own MEDL collection? and (4) How can we develop a community of individuals who provide on-the-ground support for instructors who use physical analog models in their classroom.

Jonathan F. Reichert and Barbara Wolff-Reichert Award for Excellence in Advanced Laboratory Instruction: Advanced Instructional Labs: Why Bother?

NASA Astrophysics Data System (ADS)

Bistrow, Van

What aren't we teaching about physics in the traditional lecture course? Plenty! By offering the Advanced Laboratory Course, we hope to shed light on the following questions: How do we develop a systematic process of doing experiments? How do we record procedures and results? How should we interpret theoretical concepts in the real world? What experimental and computational techniques are available for producing and analyzing data? With what degree of confidence can we trust our measurements and interpretations? How well does a theory represent physical reality? How do we collaborate with experimental partners? How do we best communicate our findings to others?These questions are of fundamental importance to experimental physics, yet are not generally addressed by reading textbooks, attending lectures or doing homework problems. Thus, to provide a more complete understanding of physics, we offer laboratory exercises as a supplement to the other modes of learning. The speaker will describe some examples of experiments, and outline the history, structure and student impressions of the Advanced Lab course at the University of Chicago Department of Physics.

Cognitive and behavioural assessment of people with traumatic brain injury in the work place: occupational therapists' perceptions.

PubMed

Bootes, Kylie; Chapparo, Christine J

2002-01-01

Cognitive and behavioural impairments, in the absence of severe physical disability, are commonly related to poor return to work outcomes for people with traumatic brain injury (TBI). Along with other health professionals, occupational therapists make judgements about cognitive and behavioural dimensions of work capacity of clients with TBI during the return to work process. Unlike many physical functional capacity evaluations, there is no standard method that therapists use to assess the ability of people with TBI to perform cognitive operations required for work. Little is known about what information occupational therapists use in their assessment of cognitive and behavioural aspects of client performance within the work place. This study employed qualitative research methods to determine what information is utilised by 20 therapists who assess the work capacity of people with TBI in the workplace. Results indicated that the process of making judgements about cognitive and behavioural competence within the work place is a multifaceted process. Therapists triangulate client information from multiple sources and types of data to produce an accurate view of client work capacity. Central to this process is the relationship between the client, the job and the work environment.

Using thermally stimulated current (TSC) to investigate disorder in micronized drug substance produced at different milling energies.

PubMed

Forcino, Rachel; Brum, Jeffrey; Galop, Marc; Sun, Yan

2010-10-01

To investigate the use of thermally stimulated current (TSC) to characterize disorder resulting from micronization of a crystalline drug substance. Samples processed at different milling energies are characterized, and annealing studied. Molecular mobility in micronized drug substance was studied using TSC and compared to results from differential scanning calorimetry (DSC). The micronized drug substance TSC spectra are compared to crystalline and amorphous references. TSC shows distinct relaxation modes for micronized material in comparison to a single weak exotherm observed with DSC. Molecular mobility modes are unique for micronized material compared to the amorphous reference indicating physically distinct disorder compared to phase-separated amorphous material. Signals are ascribed as arising from crystal defects. TSC differentiates material processed at different milling energies showing reasonable correlation between the AUC of the α-relaxation and micronization energy. The annealing process of crystal defects in micronized drug appears to proceed differently for α and β relaxations. TSC proves sensitive to the crystal defects in the micronized drug substance studied here. The technique is able to differentiate distinct types of disorder and can be used to characterize noncrystalline regions arising from milling processes which are physically distinct from amorphous material.

Heavy baryons as polarimeters at colliders

DOE PAGES

Galanti, Mario; Giammanco, Andrea; Grossman, Yuval; ...

2015-11-10

In new-physics processes that produce b or c jets, a measurement of the initial b or c-quark polarization could provide crucial information about the structure of the new physics. In the heavy-quark limit, the b and c-quark polarizations are preserved in the lightest baryons they hadronize into, Lambda(b) and Lambda(c), respectively. We revisit the prediction for the polarization retention after the hadronization process and extend it to the case of transverse polarization. We show how ATLAS and CMS can measure the b-quark polarization using semileptonic Lambda(b) decays, and the c-quark polarization using Lambda(+)(c) -> pK(-)pi(+) decays. For calibrating both measurementsmore » we suggest to use t (t) over bar samples in which these polarizations can be measured with precision of order 10% using 100thfb(-1) of data in Run 2 of the LHC. Measurements of the transverse polarization in QCD events at ATLAS, CMS and LHCb are motivated as well. The proposed measurements give access to nonperturbative QCD parameters relevant to the dynamics of the hadronization process.« less

Investigation of consolidation kinetics and microstructure evolution of Al alloys in direct metal laser sintering using phase field simulation

NASA Astrophysics Data System (ADS)

Bimal Satpathy, Bubloom; Nandy, Jyotirmoy; Sahoo, Seshadev

2018-03-01

Direct metal laser sintering is one of the very efficient processes which comes under the field of additive manufacturing and is capable of producing products of good mechanical and physical properties. The process parameters affect the physical and mechanical properties of the final products. Rapid solidification plays an important role in the consolidation kinetics as the powdered material sinters and forms a polycrystalline structure. In the recent times, the enormous use of computational modeling has helped in examining the utility of final products in a wide range of applications. In this study, a phase field model has been implemented to foresee the consolidation kinetics during the liquid state sintering. Temperature profiles have been used to study the densification behavior and neck growth which is caused by the surface diffusion of particles at initial stage. Later, importance of grain boundary and the volume diffusion during densification process is analyzed. It is also found that with rise in temperature, neck growth also increases rapidly due to the interaction of adjacent grains through grain boundary diffusion and stabilization of grain growth.

Supercomputations and big-data analysis in strong-field ultrafast optical physics: filamentation of high-peak-power ultrashort laser pulses

NASA Astrophysics Data System (ADS)

Voronin, A. A.; Panchenko, V. Ya; Zheltikov, A. M.

2016-06-01

High-intensity ultrashort laser pulses propagating in gas media or in condensed matter undergo complex nonlinear spatiotemporal evolution where temporal transformations of optical field waveforms are strongly coupled to an intricate beam dynamics and ultrafast field-induced ionization processes. At the level of laser peak powers orders of magnitude above the critical power of self-focusing, the beam exhibits modulation instabilities, producing random field hot spots and breaking up into multiple noise-seeded filaments. This problem is described by a (3  +  1)-dimensional nonlinear field evolution equation, which needs to be solved jointly with the equation for ultrafast ionization of a medium. Analysis of this problem, which is equivalent to solving a billion-dimensional evolution problem, is only possible by means of supercomputer simulations augmented with coordinated big-data processing of large volumes of information acquired through theory-guiding experiments and supercomputations. Here, we review the main challenges of supercomputations and big-data processing encountered in strong-field ultrafast optical physics and discuss strategies to confront these challenges.

Federal repatriation legislation and the role of physical anthropology in repatriation.

PubMed

Ousley, Stephen D; Billeck, William T; Hollinger, R Eric

2005-01-01

Two laws governing the disposition of Native American human remains in museums and institutions have had a profound impact on anthropology, and especially physical anthropology. In contrast to the perception of constant conflict between Native Americans and physical anthropologists, the repatriation process based on these laws has been in large part harmonious between institutions and Native peoples in the US. Despite misconceptions, the Native American Graves Protection and Repatriation Act (NAPGRA; 25 United States Code (U.S.C.) 3001-3013) was not intended to halt further research on Native American remains in museums. In fact, court decisions have affirmed that the documentation of human remains produces information no other methods can provide, and provides necessary evidence to be incorporated and weighed, along with other evidence, in evaluating "cultural affiliation," the legal term for the required connection from federally recognized Native American groups to their ancestors. The wide variety of osteological data collected at the National Museum of Natural History (NMNH), Smithsonian Institution, have proven indispensable when evaluating cultural affiliation, especially when other information sources are unhelpful or ambiguous, and provide an empirical basis for determining the ancestry of individuals whose remains will be discovered in the future. To date, the claim-driven process at the NMNH has resulted in the affiliation and repatriation of more Native American remains than any other institution in the country. Repatriation experiences at the NMNH demonstrate the changing relationships between museums and Native peoples, the continuing important contributions that physical anthropology makes to the repatriation process, and the importance of physical anthropology in understanding the recent and ancient history of North America. (c) 2005 Wiley-Liss, Inc.

Development of Phenol-Enriched Olive Oil with Phenolic Compounds Extracted from Wastewater Produced by Physical Refining.

PubMed

Venturi, Francesca; Sanmartin, Chiara; Taglieri, Isabella; Nari, Anita; Andrich, Gianpaolo; Terzuoli, Erika; Donnini, Sandra; Nicolella, Cristiano; Zinnai, Angela

2017-08-22

While in the last few years the use of olive cake and mill wastewater as natural sources of phenolic compounds has been widely considered and several studies have focused on the development of new extraction methods and on the production of functional foods enriched with natural antioxidants, no data has been available on the production of a phenol-enriched refined olive oil with its own phenolic compounds extracted from wastewater produced during physical refining. In this study; we aimed to: (i) verify the effectiveness of a multi-step extraction process to recover the high-added-value phenolic compounds contained in wastewater derived from the preliminary washing degumming step of the physical refining of vegetal oils; (ii) evaluate their potential application for the stabilization of olive oil obtained with refined olive oils; and (iii) evaluate their antioxidant activity in an in vitro model of endothelial cells. The results obtained demonstrate the potential of using the refining wastewater as a source of bioactive compounds to improve the nutraceutical value as well as the antioxidant capacity of commercial olive oils. In the conditions adopted, the phenolic content significantly increased in the prototypes of phenol-enriched olive oils when compared with the control oil.

Effects of Biochar Amendment on Soil Properties and Soil Carbon Sequestration

NASA Astrophysics Data System (ADS)

Zhang, R.; Zhu, S.

2015-12-01

Biochar addition to soils potentially affects various soil properties and soil carbon sequestration, and these effects are dependent on biochars derived from different feedstock materials and pyrolysis processes. The objective of this study was to investigate the effects of amendment of different biochars on soil physical and biological properties as well as soil carbon sequestration. Biochars were produced with dairy manure and woodchip at temperatures of 300, 500, and 700°C, respectively. Each biochar was mixed at 5% (w/w) with a forest soil and the mixture was incubated for 180 days, during which soil physical and biological properties, and soil respiration rates were measured. Results showed that the biochar addition significantly enhanced the formation of soil macroaggregates at the early incubation time. The biochar application significantly reduced soil bulk density, increased the amount of soil organic matter, and stimulated microbial activity and soil respiration rates at the early incubation stage. Biochar applications improved water retention capacity, with stronger effects by biochars produced at higher pyrolysis temperatures. At the same suction, the soil with woodchip biochars possessed higher water content than with the dairy manure biochars. Biochar addition significantly affected the soil physical and biological properties, which resulted in different soil carbon mineralization rates and the amount of soil carbon storage.

Development of Phenol-Enriched Olive Oil with Phenolic Compounds Extracted from Wastewater Produced by Physical Refining

PubMed Central

Taglieri, Isabella; Nari, Anita; Andrich, Gianpaolo; Terzuoli, Erika; Donnini, Sandra; Nicolella, Cristiano; Zinnai, Angela

2017-01-01

While in the last few years the use of olive cake and mill wastewater as natural sources of phenolic compounds has been widely considered and several studies have focused on the development of new extraction methods and on the production of functional foods enriched with natural antioxidants, no data has been available on the production of a phenol-enriched refined olive oil with its own phenolic compounds extracted from wastewater produced during physical refining. In this study; we aimed to: (i) verify the effectiveness of a multi-step extraction process to recover the high-added-value phenolic compounds contained in wastewater derived from the preliminary washing degumming step of the physical refining of vegetal oils; (ii) evaluate their potential application for the stabilization of olive oil obtained with refined olive oils; and (iii) evaluate their antioxidant activity in an in vitro model of endothelial cells. The results obtained demonstrate the potential of using the refining wastewater as a source of bioactive compounds to improve the nutraceutical value as well as the antioxidant capacity of commercial olive oils. In the conditions adopted, the phenolic content significantly increased in the prototypes of phenol-enriched olive oils when compared with the control oil. PMID:28829365

Ocean Carbon States: Data Mining in Observations and Numerical Simulations Results

NASA Astrophysics Data System (ADS)

Latto, R.; Romanou, A.

2017-12-01

Advanced data mining techniques are rapidly becoming widely used in Climate and Earth Sciences with the purpose of extracting new meaningful information from increasingly larger and more complex datasets. This is particularly important in studies of the global carbon cycle, where any lack of understanding of its combined physical and biogeochemical drivers is detrimental to our ability to accurately describe, understand, and predict CO2 concentrations and their changes in the major carbon reservoirs. The analysis presented here evaluates the use of cluster analysis as a means of identifying and comparing spatial and temporal patterns extracted from observational and model datasets. As the observational data is organized into various regimes, which we will call "ocean carbon states", we gain insight into the physical and/or biogeochemical processes controlling the ocean carbon cycle as well as how well these processes are simulated by a state-of-the-art climate model. We find that cluster analysis effectively produces realistic, dynamic regimes that can be associated with specific processes at different temporal scales for both observations and the model. In addition, we show how these regimes can be used to illustrate and characterize the model biases in the model air-sea flux of CO2. These biases are attributed to biases in salinity, sea surface temperature, wind speed, and nitrate, which are then used to identify the physical processes that are inaccurately reproduced by the model. In this presentation, we provide a proof-of-concept application using simple datasets, and we expand to more complex ones, using several physical and biogeochemical variable pairs, thus providing considerable insight into the mechanisms and phases of the ocean carbon cycle over different temporal and spatial scales.

Cirrus Simulations of CRYSTAL-FACE 23 July 2002 Case

NASA Technical Reports Server (NTRS)

Starr, David; Lin, Ruci-Fong; Demoz, Belay; Lare, Andrew

2004-01-01

A key objective of the Cirrus Regional Study of Tropical Anvils and Cirrus Layers - Florida Area Cirrus Experiment (CRYSTAL-FACE) is to understand relationships between the properties of tropical convective cloud systems and the properties and lifecycle of the extended cirrus anvils they produce. We report here on a case study of 23 July 2002 where a sequence of convective storms over central Florida produced an extensive anvil outflow. Our approach is to use a suitably-initialized cloud-system simulation with MM5 to define initial conditions and time-dependent forcing for a simulation of anvil evolution using a two-dimensional fine-resolution (100 m) cirrus cloud model that explicitly accounts for details of cirrus microphysical development (bin or spectra model) and fully interactive radiative processes. The cirrus model follows Lin. Meteorological conditions and observations for the 23 July case are described in this volume. The goals of the present study are to evaluate how well we can simulate a cirrus anvil lifecycle, to evaluate the importance of various physical processes that operate within the anvil, and to evaluate the importance of environmental conditions in regulating anvil lifecycle. CRYSTAL-FACE produced a number of excellent case studies of anvil systems that will allow environmental factors, such as static stability or wind shear in the upper troposphere, to be examined. In the present study, we strive to assess the importance of propagating gravity waves, likely produced by the deep convection itself, and radiative processes, to anvil lifecycle and characteristics.

Building Petascale Cyberinfrastructure and Science Support for Solar Physics: Approach of the DKIST Data Center

NASA Astrophysics Data System (ADS)

Berukoff, Steven; Reardon, Kevin; Hays, Tony; Spiess, DJ; Watson, Fraser

2015-08-01

When construction is complete in 2019, the Daniel K. Inouye Solar Telescope will be the most-capable large aperture, high-resolution, multi-instrument solar physics facility in the world. The telescope is designed as a four-meter off-axis Gregorian, with a rotating Coude laboratory designed to simultaneously house and support five first-light imaging and spectropolarimetric instruments. At current design, the facility and its instruments will generate data volumes of 5 PB, produce 108 images, and 107-109 metadata elements annually. This data will not only forge new understanding of solar phenomena at high resolution, but enhance participation in solar physics and further grow a small but vibrant international community.The DKIST Data Center is being designed to store, curate, and process this flood of information, while augmenting its value by providing association of science data and metadata to its acquisition and processing provenance. In early Operations, the Data Center will produce, by autonomous, semi-automatic, and manual means, quality-controlled and -assured calibrated data sets, closely linked to facility and instrument performance during the Operations lifecycle. These data sets will be made available to the community openly and freely, and software and algorithms made available through community repositories like Github for further collaboration and improvement.We discuss the current design and approach of the DKIST Data Center, describing the development cycle, early technology analysis and prototyping, and the roadmap ahead. In this budget-conscious era, a key design criterion is elasticity, the ability of the built system to adapt to changing work volumes, types, and the shifting scientific landscape, without undue cost or operational impact. We discuss our deep iterative development approach, the underappreciated challenges of calibrating ground-based solar data, the crucial integration of the Data Center within the larger Operations lifecycle, and how software and hardware support, intelligently deployed, will enable high-caliber solar physics research and community growth for the DKIST's 40-year lifespan.

Modifying Student Behavior in an Open Classroom through Changes in the Physical Design

ERIC Educational Resources Information Center

Weinstein, Carol S.

1977-01-01

Spatial distribution of activity in a second-third grade open classroom was observed before and after a change in the physical design, to test the hypothesis that minor changes in the physical setting would produce predictable, desirable changes in student behavior. In most cases the desired behavior changes were produced. (Author/MV)

Influence of Excipients and Spray Drying on the Physical and Chemical Properties of Nutraceutical Capsules Containing Phytochemicals from Black Bean Extract.

PubMed

Guajardo-Flores, Daniel; Rempel, Curtis; Gutiérrez-Uribe, Janet A; Serna-Saldívar, Sergio O

2015-12-03

Black beans (Phaseolus vulgaris L.) are a rich source of flavonoids and saponins with proven health benefits. Spray dried black bean extract powders were used in different formulations for the production of nutraceutical capsules with reduced batch-to-batch weight variability. Factorial designs were used to find an adequate maltodextrin-extract ratio for the spray-drying process to produce black bean extract powders. Several flowability properties were used to determine composite flow index of produced powders. Powder containing 6% maltodextrin had the highest yield (78.6%) and the best recovery of flavonoids and saponins (>56% and >73%, respectively). The new complexes formed by the interaction of black bean powder with maltodextrin, microcrystalline cellulose 50 and starch exhibited not only bigger particles, but also a rougher structure than using only maltodextrin and starch as excipients. A drying process prior to capsule production improved powder flowability, increasing capsule weight and reducing variability. The formulation containing 25.0% of maltodextrin, 24.1% of microcrystalline cellulose 50, 50% of starch and 0.9% of magnesium stearate produced capsules with less than 2.5% weight variability. The spray drying technique is a feasible technique to produce good flow extract powders containing valuable phytochemicals and low cost excipients to reduce the end-product variability.

Strategies for emission reduction of air pollutants produced from a chemical plant.

PubMed

Lee, Byeong-Kyu; Cho, Sung-Woong

2003-01-01

Various air pollution control (APC) techniques were employed in order to reduce emissions of air pollutants produced from chemical plants, which have many different chemical production facilities. For an emission reduction of acid gases, this study employed a method to improve solubility of pollutants by decreasing the operating temperature of the scrubbers, increasing the surface area for effective contact of gas and liquid, and modifying processes in the acid scrubbers. To reduce emission of both amines and acid gases, pollutant gas components were first separated, then condensation and/or acid scrubbing, depending on the chemical and physical properties of pollutant components, were used. To reduce emission of solvents, condensation and activated carbon adsorption were employed. To reduce emission of a mixture gases containing acid gases and solvents, the mixed gases were passed into the first condenser, the acid scrubber, the second condenser, and the activated carbon adsorption tower in sequence. As a strategy to reduce emission of pollutants at the source, this study also employed the simple pollution prevention concept of modification of the previously operating APC control device. Finally, air emissions of pollutants produced from the chemical plants were much more reduced by applying proper APC methods, depending upon the types (physical or chemical properties) and the specific emission situations of pollutants.

Uncertainties in s-process nucleosynthesis in massive stars determined by Monte Carlo variations

NASA Astrophysics Data System (ADS)

Nishimura, N.; Hirschi, R.; Rauscher, T.; St. J. Murphy, A.; Cescutti, G.

2017-08-01

The s-process in massive stars produces the weak component of the s-process (nuclei up to A ˜ 90), in amounts that match solar abundances. For heavier isotopes, such as barium, production through neutron capture is significantly enhanced in very metal-poor stars with fast rotation. However, detailed theoretical predictions for the resulting final s-process abundances have important uncertainties caused both by the underlying uncertainties in the nuclear physics (principally neutron-capture reaction and β-decay rates) as well as by the stellar evolution modelling. In this work, we investigated the impact of nuclear-physics uncertainties relevant to the s-process in massive stars. Using a Monte Carlo based approach, we performed extensive nuclear reaction network calculations that include newly evaluated upper and lower limits for the individual temperature-dependent reaction rates. We found that most of the uncertainty in the final abundances is caused by uncertainties in the neutron-capture rates, while β-decay rate uncertainties affect only a few nuclei near s-process branchings. The s-process in rotating metal-poor stars shows quantitatively different uncertainties and key reactions, although the qualitative characteristics are similar. We confirmed that our results do not significantly change at different metallicities for fast rotating massive stars in the very low metallicity regime. We highlight which of the identified key reactions are realistic candidates for improved measurement by future experiments.

On the Grand Challenges in Physical Petrology: the Multiphase Crossroads

NASA Astrophysics Data System (ADS)

Bergantz, G. W.

2014-12-01

Rapid progress in experimental, micro-analytical and textural analysis at the crystal scale has produced an unprecedented record of magmatic processes. However an obstacle to further progress is the lack of understanding of how mass, energy and momentum flux associated with crystal-rich, open-system events produces identifiable outcomes. Hence developing a physically-based understanding of magmatic systems linking micro-scale petrological observations with a physical template operating at the macro-scale presents a so-called "Grand Challenge." The essence of this challenge is that magmatic systems have characteristic length and feedback scales between those accessible by classical continuum and discrete methods. It has become increasingly obvious that the old-school continuum methods have limited resolution and power of explanation for multiphase (real) magma dynamics. This is, in part, because in crystal-rich systems the deformation is non-affine, and so the concept of constitutive behavior is less applicable and likely not even relevant, especially if one is interested in the emergent character of micro-scale processes. One expression of this is the cottage industry of proposing viscosity laws for magmas, which serves as "blunt force" de facto corrections for what is intrinsically multiphase behavior. Even in more fluid-rich systems many of these laws are not suitable for use in the very transport theories they aim to support. The alternative approach is the discrete method, where multiphase interactions are explicitly resolved. This is a daunting prospect given the numbers of crystals in magmas. But perhaps all crystals don't need to be modeled. I will demonstrate how discrete methods can recover critical state behavior, resolve crystal migration, the onset of visco-elastic behavior such as melt-present shear bands which sets the large-scale mixing volumes, some of the general morpho-dynamics that underlies purported rheological models, and transient controls on the emergence and dissipation of distinct thermodynamic states. As simulations with 106 - 107 crystals are now possible both the local, micro-scale crystal processes as well as the larger scale processes controlled by particle-particle-fluid interactions, can be simultaneously resolved.

Coastal processes of the Elwha River delta: Chapter 5 in Coastal habitats of the Elwha River, Washington--biological and physical patterns and processes prior to dam removal

USGS Publications Warehouse

Warrick, Jonathan A.; Stevens, Andrew W.; Miller, Ian M.; Gelfenbaum, Guy; Duda, Jeffrey J.; Warrick, Jonathan A.; Magirl, Christopher S.

2011-01-01

To understand the effects of increased sediment supply from dam removal on marine habitats around the Elwha River delta, a basic understanding of the region’s coastal processes is necessary. This chapter provides a summary of the physical setting of the coast near the Elwha River delta, for the purpose of synthesizing the processes that move and disperse sediment discharged by the river. One fundamental property of this coastal setting is the difference between currents in the surfzone with those in the coastal waters offshore of the surfzone. Surfzone currents are largely dictated by the direction and size of waves, and the waves that attack the Elwha River delta predominantly come from Pacific Ocean swell from the west. This establishes surfzone currents and littoral sediment transport that are eastward along much of the delta. Offshore of the surfzone the currents are largely influenced by tidal circulation and the physical constraint to flow provided by the delta’s headland. During both ebbing and flooding tides, the flow separates from the coast at the tip of the delta’s headland, and this produces eddies on the downstream side of the headland. Immediately offshore of the Elwha River mouth, this creates a situation in which the coastal currents are directed toward the east much more frequently than toward the west. This suggests that Elwha River sediment will be more likely to move toward the east in the coastal system.

The Imaging X-Ray Polarimetry Explorer (IXPE)

NASA Technical Reports Server (NTRS)

Weisskopf, Martin C.; Ramsey, Brian; O’Dell, Stephen; Tennant, Allyn; Elsner, Ronald; Soffita, Paolo; Bellazzini, Ronaldo; Costa, Enrico; Kolodziejczak, Jeffery; Kaspi, Victoria;

What should be our approach to understanding the universe?

NASA Astrophysics Data System (ADS)

Chang, Hui-Yiing

2006-10-01

Besides understanding the concepts of physics and learning to apply them to different contexts, it is most crucial that students examine the basis of their beliefs in these theories. It becomes necessary, then, to expand our conception considerably beyond the scope of the physics textbook. This process is possibly effectuated by gaining a representative understanding of the liberal arts through study of several areas, and self-expression of one's convictions. Respecting of differences is important, as well as the expectation that proposing of new ideas is often accompanied by conflict and disequilibrium within individuals and the community. In this session, we will discuss the approaches of significant ancient scientists and philosophers to understanding the universe, and trace the development to modern conventionally accepted theories. A higher goal of physics education is to produce ``reforming physicists'' that unravel the truth for the betterment of society.

Enrico Fermi - And the Revolutions of Modern Physics

NASA Astrophysics Data System (ADS)

Cooper, Dan

1999-02-01

In 1938, at the age of 37, Enrico Fermi was awarded the Nobel Prize in Physics. That same year he emigrated from Italy to the United States and, in the course of his experiments, discovered nuclear fission--a process which forms the basis of nuclear power and atomic bombs. Soon the brilliant physicist was involved in the top secret race to produce the deadliest weapon on Earth. He created the first self-sustaining chain reaction, devised new methods for purifying plutonium, and eventually participated in the first atomic test. This compelling biography traces Fermis education in Italy, his meteoric career in the scientific world, his escape from fascism to America, and the ingenious experiments he devised and conducted at the University of Rome, Columbia University, and the Los Alamos laboratory. The book also presents a mini-course in quantum and nuclear physics in an accessible, fast-paced narrative that invokes all the dizzying passion of Fermis brilliant discoveries.

Assessing security technology's impact: old tools for new problems.

PubMed

Kreissl, Reinhard

2014-09-01

The general idea developed in this paper from a sociological perspective is that some of the foundational categories on which the debate about privacy, security and technology rests are blurring. This process is a consequence of a blurring of physical and digital worlds. In order to define limits for legitimate use of intrusive digital technologies, one has to refer to binary distinctions such as private versus public, human versus technical, security versus insecurity to draw differences determining limits for the use of surveillance technologies. These distinctions developed in the physical world and are rooted in a cultural understanding of pre-digital culture. Attempts to capture the problems emerging with the implementation of security technologies using legal reasoning encounter a number of problems since law is by definition oriented backwards, adapting new developments to existing traditions, whereas the intrusion of new technologies in the physical world produces changes and creates fundamentally new problems.

Carbon Radiation Studies in the DIII-D Divertor with the Monte Carlo Impurity (MCI) Code

NASA Astrophysics Data System (ADS)

Evans, T. E.; Leonard, A. W.; West, W. P.; Finkenthal, D. F.; Fenstermacher, M. E.; Porter, G. D.; Chu, Y.

1998-11-01

Carbon sputtering and transport are modeled in the DIII--D divertor with the MCI code. Calculated 2-D radiation patterns are compared with measured radiation distributions. The results are particularly sensitive to Ti near the divertor target plates. For example, increasing the ion temperature from 8 eV to 20 eV in MCI raises P_rad^div from 1626 to 2862 kW. Although this presents difficulties in assessing which sputtering model best describes the plasma-surface interaction physics (because of experimental uncertainties in T_i), processes which either produce too much or too little radiated power compared to the measured value of 1718 kW can be eliminated. Based on this, the number of viable sputtering options has been reduced from 12 to 4. For the conditions studied, three of these options involve both physical and chemical sputtering, and one requires only physical sputtering.

The Origin of r-process Elements in the Milky Way

NASA Astrophysics Data System (ADS)

Côté, Benoit; Fryer, Chris L.; Belczynski, Krzysztof; Korobkin, Oleg; Chruślińska, Martyna; Vassh, Nicole; Mumpower, Matthew R.; Lippuner, Jonas; Sprouse, Trevor M.; Surman, Rebecca; Wollaeger, Ryan

2018-03-01

Some of the heavy elements, such as gold and europium (Eu), are almost exclusively formed by the rapid neutron capture process (r-process). However, it is still unclear which astrophysical site between core-collapse supernovae and neutron star–neutron star (NS–NS) mergers produced most of the r-process elements in the universe. Galactic chemical evolution (GCE) models can test these scenarios by quantifying the frequency and yields required to reproduce the amount of europium (Eu) observed in galaxies. Although NS–NS mergers have become popular candidates, their required frequency (or rate) needs to be consistent with that obtained from gravitational wave measurements. Here, we address the first NS–NS merger detected by LIGO/Virgo (GW170817) and its associated gamma-ray burst and analyze their implication for the origin of r-process elements. The range of NS–NS merger rate densities of 320–4740 Gpc‑3 yr‑1 provided by LIGO/Virgo is remarkably consistent with the range required by GCE to explain the Eu abundances in the Milky Way with NS–NS mergers, assuming the solar r-process abundance pattern for the ejecta. Under the same assumption, this event has produced about 1–5 Earth masses of Eu, and 3–13 Earth masses of gold. When using theoretical calculations to derive Eu yields, constraining the role of NS–NS mergers becomes more challenging because of nuclear astrophysics uncertainties. This is the first study that directly combines nuclear physics uncertainties with GCE calculations. If GW170817 is a representative event, NS–NS mergers can produce Eu in sufficient amounts and are likely to be the main r-process site.

High contrast laser marking of alumina

NASA Astrophysics Data System (ADS)

Penide, J.; Quintero, F.; Riveiro, A.; Fernández, A.; del Val, J.; Comesaña, R.; Lusquiños, F.; Pou, J.

2015-05-01

Alumina serves as raw material for a broad range of advanced ceramic products. These elements should usually be identified by some characters or symbols printed directly on them. In this sense, laser marking is an efficient, reliable and widely implemented process in industry. However, laser marking of alumina still leads to poor results since the process is not able to produce a dark mark, yielding bad contrast. In this paper, we present an experimental study on the process of marking alumina by three different lasers working in two wavelengths: 1064 nm (Near-infrared) and 532 nm (visible, green radiation). A colorimetric analysis has been carried out in order to compare the resulting marks and its contrast. The most suitable laser operating conditions were also defined and are reported here. Moreover, the physical process of marking by NIR lasers is discussed in detail. Field Emission Scanning Electron Microscopy, High Resolution Transmission Electron Microscopy and X-ray Photoelectron Spectroscopy were also employed to analyze the results. Finally, we propose an explanation for the differences of the coloration induced under different atmospheres and laser parameters. We concluded that the atmosphere is the key parameter, being the inert one the best choice to produce the darkest marks.

Case studies on the physical-chemical parameters' variation during three different purification approaches destined to treat wastewaters from food industry.

PubMed

Ghimpusan, Marieta; Nechifor, Gheorghe; Nechifor, Aurelia-Cristina; Dima, Stefan-Ovidiu; Passeri, Piero

2017-12-01

The paper presents a set of three interconnected case studies on the depuration of food processing wastewaters by using aeration & ozonation and two types of hollow-fiber membrane bioreactor (MBR) approaches. A secondary and more extensive objective derived from the first one is to draw a clearer, broader frame on the variation of physical-chemical parameters during the purification of wastewaters from food industry through different operating modes with the aim of improving the management of water purification process. Chemical oxygen demand (COD), pH, mixed liquor suspended solids (MLSS), total nitrogen, specific nitrogen (NH 4 + , NO 2 - , NO 3 - ) total phosphorous, and total surfactants were the measured parameters, and their influence was discussed in order to establish the best operating mode to achieve the purification performances. The integrated air-ozone aeration process applied in the second operating mode lead to a COD decrease by up to 90%, compared to only 75% obtained in a conventional biological activated sludge process. The combined purification process of MBR and ozonation produced an additional COD decrease of 10-15%, and made the Total Surfactants values to comply to the specific legislation. Copyright © 2016 Elsevier Ltd. All rights reserved.

The effect of meditation on physical and mental health in junior college students: a quasi-experimental study.

PubMed

Yang, Ke-Ping; Su, Whei-Ming; Huang, Chen-Kuan

2009-12-01

Physical stress and mental stress are increasingly common phenomena in our rapidly changing and stressful modern society. Research has found meditation to produce positive and demonstrable stress reduction effects on brain and immune functions. This study is grounded in traditional Chinese philosophical mores that teach a process summarized by the keynote activities of "calm, still, quiet, consider, and get" and the potential of this process to reduce stress in adolescents. The purpose of this study was to examine the effects of meditation on the physical and mental health of junior college students. This research employed a quasi-experimental design. Participants included 242 freshmen from a junior college in Taiwan selected using a convenience sampling technique. Participants were then randomly separated into experimental (n = 119) and control (n = 123) groups. The project duration was 18 weeks, during which the experimental group received 2 hours of meditation treatment per week, for a total of 36 hours. Both groups completed pretest and posttest Life Adaptation Scale forms, which included questionnaires addressing information on physical and mental distress and positive and negative coping strategies. Data were analyzed using analysis of covariance. Findings showed that the effect of the experiment treatment was significant when student physical and mental distress pretest scores were controlled. Physical and mental symptoms in the experimental group were lower than those in the control group. Meditation can help students to adapt to life stressors. This study also provides support for traditional Chinese wisdom, which promotes meditation as one way to improve health.

Designing dual-plate meteoroid shields: A new analysis

NASA Technical Reports Server (NTRS)

Swift, H. F.; Bamford, R.; Chen, R.

1982-01-01

Physics governing ultrahigh velocity impacts onto dual-plate meteor armor is discussed. Meteoroid shield design methodologies are considered: failure mechanisms, qualitative features of effective meteoroid shield designs, evaluating/processing meteoroid threat models, and quantitative techniques for optimizing effective meteoroid shield designs. Related investigations are included: use of Kevlar cloth/epoxy panels in meteoroid shields for the Halley's Comet intercept vehicle, mirror exposure dynamics, and evaluation of ion fields produced around the Halley Intercept Mission vehicle by meteoroid impacts.

Production of bio-jet fuel from microalgae

NASA Astrophysics Data System (ADS)

Elmoraghy, Marian

The increase in petroleum-based aviation fuel consumption, the decrease in petroleum resources, the fluctuation of the crude oil price, the increase in greenhouse gas emission and the need for energy security are motivating the development of an alternate jet fuel. Bio-jet fuel has to be a drop in fuel, technically and economically feasible, environmentally friendly, greener than jet fuel, produced locally and low gallon per Btu. Bic jet fuel has been produced by blending petro-based jet fuel with microalgae biodiesel (Fatty Acid Methyl Ester, or simply FAME). Indoor microalgae growth, lipids extraction and transetrification to biodiesel are energy and fresh water intensive and time consuming. In addition, the quality of the biodiesel product and the physical properties of the bio-jet fuel blends are unknown. This work addressed these challenges. Minimizing the energy requirements and making microalgae growth process greener were accomplished by replacing fluorescent lights with light emitting diodes (LEDs). Reducing fresh water footprint in algae growth was accomplished by waste water use. Microalgae biodiesel production time was reduced using the one-step (in-situ transestrification) process. Yields up to 56.82 mg FAME/g dry algae were obtained. Predicted physical properties of in-situ FAME satisfied European and American standards confirming its quality. Lipid triggering by nitrogen deprivation was accomplished in order to increase the FAME production. Bio-jet fuel freezing points and heating values were measured for different jet fuel to biodiesel blend ratios.

Is our brain hardwired to produce God, or is our brain hardwired to perceive God? A systematic review on the role of the brain in mediating religious experience.

PubMed

Fingelkurts, Alexander A; Fingelkurts, Andrew A

2009-11-01

To figure out whether the main empirical question "Is our brain hardwired to believe in and produce God, or is our brain hardwired to perceive and experience God?" is answered, this paper presents systematic critical review of the positions, arguments and controversies of each side of the neuroscientific-theological debate and puts forward an integral view where the human is seen as a psycho-somatic entity consisting of the multiple levels and dimensions of human existence (physical, biological, psychological, and spiritual reality), allowing consciousness/mind/spirit and brain/body/matter to be seen as different sides of the same phenomenon, neither reducible to each other. The emergence of a form of causation distinctive from physics where mental/conscious agency (a) is neither identical with nor reducible to brain processes and (b) does exert "downward" causal influence on brain plasticity and the various levels of brain functioning is discussed. This manuscript also discusses the role of cognitive processes in religious experience and outlines what can neuroscience offer for study of religious experience and what is the significance of this study for neuroscience, clinicians, theology and philosophy. A methodological shift from "explanation" to "description" of religious experience is suggested. This paper contributes to the ongoing discussion between theologians, cognitive psychologists and neuroscientists.

The effect of chars and their water extractable organic carbon (WEOC) fractions on atrazine adsorption-desorption processes

NASA Astrophysics Data System (ADS)

Cavoski, I.; Jablonowski, N.; Burauel, P.; Miano, T.

2012-04-01

Chars are carbonaceous material produced from different type of biomass by pyrolysis. They are known as highly effective adsorbents for atrazine therefore limiting its degradation and its diffusion into the aqueous phase. The aim of the present work is to study the effects of different chars and char's derived WEOC on atrazine sorption-desorption processes. The five chars been used in this study derived from: 1) fast pyrolysis from hard wood (FP1); 2) flash pyrolysis from soft wood (FP2); 3) slow pyrolysis from deciduous wood (CC); 4) gasification from deciduous wood (GC) and 5) the market, purchased as activated charcoal standard (AC). Short-term batch equilibration tests were conducted to assess the sorption-desorption behavior of 14C-labeled atrazine on the chars, with a special focus on the desorption behavior using successive dilution method with six consecutive desorption step. Chars and their WEOC were physically and chemically characterized. Results demonstrate that biomass and pyrolysis process used to produce chars affect their physical and chemical properties, and atrazine adsorption-desorption behavior. Atrazine desorption resulted from the positive and competitive interactions between WEOC and chars surfaces. WEOC pool play important role in atrazine adsorption-desorption behavior. FP1 and FP2 with higher concentration of WEOC showed higher desorption rates, whereas GC, CC and AC with insignificant WEOC concentration strongly adsorb atrazine with low desorption rates. According to our results, when high WEOC pools chars are concerned, an increase in atrazine desorption can be observed but further studies would help in confirming the present results.

Environmental, Economic, and Scalability Considerations and Trends of Selected Fuel Economy-Enhancing Biomass-Derived Blendstocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dunn, Jennifer B.; Biddy, Mary; Jones, Susanne

Twenty-four biomass-derived compounds and mixtures, identified based on their physical properties, which could be blended into fuels to improve spark ignition engine fuel economy, were assessed for their economic, technology readiness, and environmental viability. These bio-blendstocks were modeled to be produced biochemically, thermochemically, or through hybrid processes. To carry out the assessment, 17 metrics were developed for which each bio-blendstock was determined to be favorable, neutral, or unfavorable. Cellulosic ethanol was included as a reference case. Overall economic and, to some extent, environmental viability is driven by projected yields for each of these processes. The metrics used in this analysismore » methodology highlight the near-term potential to achieve these targeted yield estimates when considering data quality and current technical readiness for these conversion strategies. Key knowledge gaps included the degree of purity needed for use as a bio-blendstock. Less stringent purification requirements for fuels could cut processing costs and environmental impacts. Additionally, more information is needed on the blending behavior of many of these bio-blendstocks with gasoline to support the technology readiness evaluation. Altogether, the technology to produce many of these blendstocks from biomass is emerging, and as it matures, these assessments must be revisited. Importantly, considering economic, environmental, and technology readiness factors, in addition to physical properties of blendstocks that could be used to boost engine efficiency and fuel economy, in the early stages of project research and development can help spotlight those most likely to be viable in the near term.« less

Environmental, Economic, and Scalability Considerations and Trends of Selected Fuel Economy-Enhancing Biomass-Derived Blendstocks

DOE PAGES

Dunn, Jennifer B.; Biddy, Mary; Jones, Susanne; ...

2017-10-30

Twenty-four biomass-derived compounds and mixtures, identified based on their physical properties, which could be blended into fuels to improve spark ignition engine fuel economy, were assessed for their economic, technology readiness, and environmental viability. These bio-blendstocks were modeled to be produced biochemically, thermochemically, or through hybrid processes. To carry out the assessment, 17 metrics were developed for which each bio-blendstock was determined to be favorable, neutral, or unfavorable. Cellulosic ethanol was included as a reference case. Overall economic and, to some extent, environmental viability is driven by projected yields for each of these processes. The metrics used in this analysismore » methodology highlight the near-term potential to achieve these targeted yield estimates when considering data quality and current technical readiness for these conversion strategies. Key knowledge gaps included the degree of purity needed for use as a bio-blendstock. Less stringent purification requirements for fuels could cut processing costs and environmental impacts. Additionally, more information is needed on the blending behavior of many of these bio-blendstocks with gasoline to support the technology readiness evaluation. Altogether, the technology to produce many of these blendstocks from biomass is emerging, and as it matures, these assessments must be revisited. Importantly, considering economic, environmental, and technology readiness factors, in addition to physical properties of blendstocks that could be used to boost engine efficiency and fuel economy, in the early stages of project research and development can help spotlight those most likely to be viable in the near term.« less

Gaussian process model for extrapolation of scattering observables for complex molecules: From benzene to benzonitrile

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cui, Jie; Krems, Roman V.; Li, Zhiying

2015-10-21

We consider a problem of extrapolating the collision properties of a large polyatomic molecule A–H to make predictions of the dynamical properties for another molecule related to A–H by the substitution of the H atom with a small molecular group X, without explicitly computing the potential energy surface for A–X. We assume that the effect of the −H →−X substitution is embodied in a multidimensional function with unknown parameters characterizing the change of the potential energy surface. We propose to apply the Gaussian Process model to determine the dependence of the dynamical observables on the unknown parameters. This can bemore » used to produce an interval of the observable values which corresponds to physical variations of the potential parameters. We show that the Gaussian Process model combined with classical trajectory calculations can be used to obtain the dependence of the cross sections for collisions of C{sub 6}H{sub 5}CN with He on the unknown parameters describing the interaction of the He atom with the CN fragment of the molecule. The unknown parameters are then varied within physically reasonable ranges to produce a prediction uncertainty of the cross sections. The results are normalized to the cross sections for He — C{sub 6}H{sub 6} collisions obtained from quantum scattering calculations in order to provide a prediction interval of the thermally averaged cross sections for collisions of C{sub 6}H{sub 5}CN with He.« less

Tensegrity II. How structural networks influence cellular information processing networks

NASA Technical Reports Server (NTRS)

Ingber, Donald E.

2003-01-01

The major challenge in biology today is biocomplexity: the need to explain how cell and tissue behaviors emerge from collective interactions within complex molecular networks. Part I of this two-part article, described a mechanical model of cell structure based on tensegrity architecture that explains how the mechanical behavior of the cell emerges from physical interactions among the different molecular filament systems that form the cytoskeleton. Recent work shows that the cytoskeleton also orients much of the cell's metabolic and signal transduction machinery and that mechanical distortion of cells and the cytoskeleton through cell surface integrin receptors can profoundly affect cell behavior. In particular, gradual variations in this single physical control parameter (cell shape distortion) can switch cells between distinct gene programs (e.g. growth, differentiation and apoptosis), and this process can be viewed as a biological phase transition. Part II of this article covers how combined use of tensegrity and solid-state mechanochemistry by cells may mediate mechanotransduction and facilitate integration of chemical and physical signals that are responsible for control of cell behavior. In addition, it examines how cell structural networks affect gene and protein signaling networks to produce characteristic phenotypes and cell fate transitions during tissue development.

Comparison of a Conceptual Groundwater Model and Physically Based Groundwater Mode

NASA Astrophysics Data System (ADS)

Yang, J.; Zammit, C.; Griffiths, J.; Moore, C.; Woods, R. A.

2017-12-01

Groundwater is a vital resource for human activities including agricultural practice and urban water demand. Hydrologic modelling is an important way to study groundwater recharge, movement and discharge, and its response to both human activity and climate change. To understand the groundwater hydrologic processes nationally in New Zealand, we have developed a conceptually based groundwater flow model, which is fully integrated into a national surface-water model (TopNet), and able to simulate groundwater recharge, movement, and interaction with surface water. To demonstrate the capability of this groundwater model (TopNet-GW), we applied the model to an irrigated area with water shortage and pollution problems in the upper Ruamahanga catchment in Great Wellington Region, New Zealand, and compared its performance with a physically-based groundwater model (MODFLOW). The comparison includes river flow at flow gauging sites, and interaction between groundwater and river. Results showed that the TopNet-GW produced similar flow and groundwater interaction patterns as the MODFLOW model, but took less computation time. This shows the conceptually-based groundwater model has the potential to simulate national groundwater process, and could be used as a surrogate for the more physically based model.

The Olympic Mountains Experiment for GPM (OLYMPEX)

NASA Astrophysics Data System (ADS)

Houze, R.; McMurdie, L. A.; Petersen, W. A.; Schwaller, M.

2016-12-01

The GPM satellite has made it possible to observe the amount and nature of precipitation in remote areas of midlatitudes, including oceans and mountain ranges. OLYMPEX conducted over the Olympic Mountains on the northwest coast of Washington State was designed to provide the means for evaluating the physical basis of the algorithms used to convert GPM satellite measurements to determine the amount and nature of precipitation in midlatitude extratropical cyclones. Microphysical processes producing precipitation are highly sensitive to the vertical profile of temperature. In the tropics, the domain of the TRMM satellite, the temperature profile varies only slightly. GPM algorithms, however, must account for the strong horizontal variation of temperature profiles in baroclinic storms systems of midlatitudes and for the variations of precipitation mechanisms caused by passage of these storms over mountains. The OLYMPEX scientific strategy was: 1) collect a statistically robust set of measurements in midlatitude cyclones upstream of, over, and downstream of a midlatitude mountain range that can be used to improve GPM satellite algorithms; 2) determine how the physics and dynamics of the mechanisms affecting precipitation formation in relation to storm structure and terrain. To accomplish these goals 3 aircraft, 4 scanning dual polarization Doppler radars, supplemental soundings, and sophisticated surface instruments were deployed on the Olympic Peninsula of Washington, where Pacific frontal systems produce seasonal precipitation of 2000-4000 mm. 13 storms were observed. 3 of these were atmospheric rivers. The NASA DC-8 and ER-2 aircraft overflew the storms with instruments similar to those on GPM. The U. North Dakota Citation sampled hydrometeors in situ. Preliminary analysis indicates that one of the primary modes of orographic enhancement is low-level moist flow rising over the lower windward slopes and producing many very small drops. Ice-phase processes producing larger particles also vary in relation to shear-enhanced turbulence over topography.

The 8th International Conference on Laser Ablation (COLA' 05); Journal of Physics: Conference Series

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hess, Wayne P.; Herman, Peter R.; Bauerle, Dieter W.

2007-09-01

Laser ablation encompasses a wide range of delicate to extreme light interactions with matter that present considerably challenging problems for scientists to study and understand. At the same time, laser ablation also represents a basic process of significant commercial importance in laser material processing—defining a multi-billion dollar industry today. These topics were widely addressed at the 8th International Conference on Laser Ablation (COLA), held in Banff, Canada on 11–16 September 2005. The meeting took place amongst the majestic and natural beauty of the Canadian Rocky Mountains at The Banff Centre, where delegates enjoyed many inspiring presentations and discussions in amore » unique campus learning environment. The conference brought together world leading scientists, students and industry representatives to examine the basic science of laser ablation and improve our understanding of the many physical, chemical and/or biological processes driven by the laser. The multi-disciplinary research presented at the meeting underlies some of our most important trends at the forefront of science and technology today that are represented in the papers collected in this volume. Here you will find new processes that are producing novel types of nanostructures and nano-materials with unusual and promising properties. Laser processes are described for delicately manipulating living cells or modifying their internal structure with unprecedented degrees of control and precision. Learn about short-pulse lasers that are driving extreme physical processes on record-fast time scales and opening new directions from material processing applications. The conference papers further highlight forefront application areas in pulsed laser deposition, nanoscience, analytical methods, materials, and microprocessing applications.« less

Introduction to Particle Acceleration in the Cosmos

NASA Technical Reports Server (NTRS)

Gallagher, D. L.; Horwitz, J. L.; Perez, J.; Quenby, J.

2005-01-01

Accelerated charged particles have been used on Earth since 1930 to explore the very essence of matter, for industrial applications, and for medical treatments. Throughout the universe nature employs a dizzying array of acceleration processes to produce particles spanning twenty orders of magnitude in energy range, while shaping our cosmic environment. Here, we introduce and review the basic physical processes causing particle acceleration, in astrophysical plasmas from geospace to the outer reaches of the cosmos. These processes are chiefly divided into four categories: adiabatic and other forms of non-stochastic acceleration, magnetic energy storage and stochastic acceleration, shock acceleration, and plasma wave and turbulent acceleration. The purpose of this introduction is to set the stage and context for the individual papers comprising this monograph.

Process for controlling morphology and improving thermal-mechanical performance of high performance interpenetrating and semi-interpenetrating polymer networks

NASA Technical Reports Server (NTRS)

Pater, Ruth H. (Inventor); Hansen, Marion G. (Inventor)

1997-01-01

In the process of the present invention, a non-polar, aprotic solvent is removed from an oligomer/polymer solution by freeze-drying in order to produce IPNs and semi-IPNs. By thermally quenching the solution to a solid in a short length of time, the size of the minor constituent-rich regions is greatly reduced as they are excluded along with the major constituent from the regions of crystallizing solvent. The use of this process sequence of controlling phase morphology provides IPNs and semi-IPNs with improved fracture toughness, microcracking resistance, and other physical-mechanical properties as compared to IPNs and semi-IPNs formed when the solvent is evaporated rather than sublimed.

Process for controlling morphology and improving thermal mechanical performance of high performance interpenetrating and semiinterpenetrating polymer networks

NASA Technical Reports Server (NTRS)

Pater, Ruth H. (Inventor); Hansen, Marion G. (Inventor)

1998-01-01

In the process of the present invention, a non-polar, aprotic solvent is removed from an oligomer/polymer solution by freeze-drying in order to produce IPNs and semi-IPNs. By thermally quenching the solution to a solid in a short length of time, the size of the minor constituent-rich regions is greatly reduced as they are excluded along with the major constituent from the regions of crystallizing solvent. The use of this process sequence of controlling phase morphology provides IPNs and semi-IPNs with improved fracture toughness, microcracking resistance, and other physical-mechanical properties as compared to IPNs and semi-IPNs formed when the solvent is evaporated rather than sublimed.

FAST Spacecraft Battery Design and Performance

NASA Technical Reports Server (NTRS)

Jung, David S.; Rao, Gopalakrishna; Ahmad, Anisa

1997-01-01

The Fast Auroral Snapshot (FAST) Explorer spacecraft is to study the physical processes that produce the aurora borealis and aurora australis. It is a unique plasma physics experiment that will take fundamental measurements of the magnetic and electrical fields. This investigation will add significantly to our understanding of the near-earth space environments and its effect. The FAST has a 1 year requirement and 3-year goal for its mission life in low earth orbit. The FAST power power system topology is a Direct Energy Transfer (DET) system based on the SAMPEX design. The FAST flight battery supplies power to the satellite during pre-launch operations, the launch phase, the eclipse periods for all mission phases, and when the load is about 50 watts.

Floquet-Engineered Valleytronics in Dirac Systems.

PubMed

Kundu, Arijit; Fertig, H A; Seradjeh, Babak

2016-01-08

Valley degrees of freedom offer a potential resource for quantum information processing if they can be effectively controlled. We discuss an optical approach to this problem in which intense light breaks electronic symmetries of a two-dimensional Dirac material. The resulting quasienergy structures may then differ for different valleys, so that the Floquet physics of the system can be exploited to produce highly polarized valley currents. This physics can be utilized to realize a valley valve whose behavior is determined optically. We propose a concrete way to achieve such valleytronics in graphene as well as in a simple model of an inversion-symmetry broken Dirac material. We study the effect numerically and demonstrate its robustness against moderate disorder and small deviations in optical parameters.

Cosmogenically-produced isotopes in natural and enriched high-purity germanium detectors for the MAJORANA DEMONSTRATOR

NASA Astrophysics Data System (ADS)

Gilliss, Thomas; MAJORANA DEMONSTRATOR Collaboration

2017-01-01

The MAJORANA DEMONSTRATOR advances toward measurements of the neutrinoless double-beta decay of 76Ge. Detectors employed in the DEMONSTRATOR are subject to cosmogenic spallation during production and processing, resulting in activation of certain long-lived radioisotopes. Activation of these cosmogenic isotopes is mitigated by shielded storage of detectors and through underground operation of the DEMONSTRATOR at the 4850 ft level of the Sanford Underground Research Facility. In this work, we explore the appearance and reduction of cosmogenic contributions to the DEMONSTRATOR background spectrum. This work is supported by the U.S. Department of Energy, Office of Science, Office of Nuclear Physics, the Particle Astrophysics and Nuclear Physics Programs of the National Science Foundation, and the Sanford Underground Research Facility.

Uncertainties in s -process nucleosynthesis in low mass stars determined from Monte Carlo variations

NASA Astrophysics Data System (ADS)

Cescutti, G.; Hirschi, R.; Nishimura, N.; den Hartogh, J. W.; Rauscher, T.; Murphy, A. St J.; Cristallo, S.

2018-05-01

The main s-process taking place in low mass stars produces about half of the elements heavier than iron. It is therefore very important to determine the importance and impact of nuclear physics uncertainties on this process. We have performed extensive nuclear reaction network calculations using individual and temperature-dependent uncertainties for reactions involving elements heavier than iron, within a Monte Carlo framework. Using this technique, we determined the uncertainty in the main s-process abundance predictions due to nuclear uncertainties link to weak interactions and neutron captures on elements heavier than iron. We also identified the key nuclear reactions dominating these uncertainties. We found that β-decay rate uncertainties affect only a few nuclides near s-process branchings, whereas most of the uncertainty in the final abundances is caused by uncertainties in neutron capture rates, either directly producing or destroying the nuclide of interest. Combined total nuclear uncertainties due to reactions on heavy elements are in general small (less than 50%). Three key reactions, nevertheless, stand out because they significantly affect the uncertainties of a large number of nuclides. These are 56Fe(n,γ), 64Ni(n,γ), and 138Ba(n,γ). We discuss the prospect of reducing uncertainties in the key reactions identified in this study with future experiments.

Trident: A Universal Tool for Generating Synthetic Absorption Spectra from Astrophysical Simulations

NASA Astrophysics Data System (ADS)

Hummels, Cameron B.; Smith, Britton D.; Silvia, Devin W.

2017-09-01

Hydrodynamical simulations are increasingly able to accurately model physical systems on stellar, galactic, and cosmological scales; however, the utility of these simulations is often limited by our ability to directly compare them with the data sets produced by observers: spectra, photometry, etc. To address this problem, we have created trident, a Python-based open-source tool for post-processing hydrodynamical simulations to produce synthetic absorption spectra and related data. trident can (I) create absorption-line spectra for any trajectory through a simulated data set mimicking both background quasar and down-the-barrel configurations; (II) reproduce the spectral characteristics of common instruments like the Cosmic Origins Spectrograph; (III) operate across the ultraviolet, optical, and infrared using customizable absorption-line lists; (IV) trace simulated physical structures directly to spectral features; (v) approximate the presence of ion species absent from the simulation outputs; (VI) generate column density maps for any ion; and (vii) provide support for all major astrophysical hydrodynamical codes. trident was originally developed to aid in the interpretation of observations of the circumgalactic medium and intergalactic medium, but it remains a general tool applicable in other contexts.

Characterization of activated carbons from oil-palm shell by CO2 activation with no holding carbonization temperature.

PubMed

Herawan, S G; Hadi, M S; Ayob, Md R; Putra, A

2013-01-01

Activated carbons can be produced from different precursors, including coals of different ranks, and lignocellulosic materials, by physical or chemical activation processes. The objective of this paper is to characterize oil-palm shells, as a biomass byproduct from palm-oil mills which were converted into activated carbons by nitrogen pyrolysis followed by CO2 activation. The effects of no holding peak pyrolysis temperature on the physical characteristics of the activated carbons are studied. The BET surface area of the activated carbon is investigated using N2 adsorption at 77 K with selected temperatures of 500, 600, and 700°C. These pyrolysis conditions for preparing the activated carbons are found to yield higher BET surface area at a pyrolysis temperature of 700°C compared to selected commercial activated carbon. The activated carbons thus result in well-developed porosities and predominantly microporosities. By using this activation method, significant improvement can be obtained in the surface characteristics of the activated carbons. Thus this study shows that the preparation time can be shortened while better results of activated carbon can be produced.

Laboratory Studies in UV and EUV Solar Physics

NASA Technical Reports Server (NTRS)

Parkinson, W. H.; Wagner, William J. (Technical Monitor)

2002-01-01

The Ion Beam Experiment at the Center for Astrophysics is dedicated to the study of ion-electron collision processes of importance in solar physics. The analysis of measurements of Electron Impact Excitation (EIE) from the 3s3p(exp 3)P(exp o) metastable state to the 3s3p(exp 1)P state of Si(2+) was completed during the past year and a paper describing the results is available as a preprint. Our current program is directed at measuring absolute cross sections for dielectronic recombination (DR) and EIE in Si(3+), one of the primary ions used for probing the solar transition region. Our study of DR is particularly concerned with the effects of electric and magnetic fields on the recombination rates. Measurements of silicon ions with charge greater than n=2 have necessitated upgrading the experiment with a new ion source. The new source is also suitable for producing C(2+) beams to be used for measurements of EIE and DR for that system. The source is expected to be capable of producing beams of more highly charged systems as well.

Recovery of protein hydrolysate and chitosan from black tiger shrimp (Penaeus monodon) heads: approaching a zero waste process.

PubMed

Phuong, Pham Thi Dan; Minh, Nguyen Cong; Cuong, Hoang Ngoc; Van Minh, Nguyen; Han, Nguyen The; Van Hoa, Nguyen; Yen, Ha Thi Hai; Trung, Trang Si

2017-06-01

Shrimp heads are considered as a potential source for the recovery of many valuable components such as chitin, protein and carotenoids. In the present study, both protein hydrolysate and chitin/chitosan were recovered using combination of physical, biological and chemical treatments. Shrimp heads were separated from liquid phase by a facile and efficient physical pretreatment. The liquid fraction was then hydrolyzed using formic acid and vacuum concentrated to obtain an astaxanthin-rich protein hydrolysate. The solid fraction was used to produce chitin by deproteination and demineralization. The hydrolysate consisted of a high astaxanthin (192 ppm) and protein (26.3 wt%) content. Chitosan prepared from chitin showed a high degree of deacetylation (85.4%) with low protein (0.25 wt%) and mineral (0.22 wt%) contents. The relative crystalline structure of the chitin and chitosan were 54.7 and 10.4%, respectively. The deacetylation of chitin was confirmed by Fourier Transform Infrared Spectroscopy. The present procedure approached to produce maximum valuable components including astaxanthin-rich protein hydrolysate and chitin/chitosan from shrimp head waste.

PREDICTION METRICS FOR CHEMICAL DETECTION IN LONG-WAVE INFRARED HYPERSPECTRAL IMAGERY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chilton, M.; Walsh, S.J.; Daly, D.S.

2009-01-01

Natural and man-made chemical processes generate gaseous plumes that may be detected by hyperspectral imaging, which produces a matrix of spectra affected by the chemical constituents of the plume, the atmosphere, the bounding background surface and instrument noise. A physics-based model of observed radiance shows that high chemical absorbance and low background emissivity result in a larger chemical signature. Using simulated hyperspectral imagery, this study investigated two metrics which exploited this relationship. The objective was to explore how well the chosen metrics predicted when a chemical would be more easily detected when comparing one background type to another. The twomore » predictor metrics correctly rank ordered the backgrounds for about 94% of the chemicals tested as compared to the background rank orders from Whitened Matched Filtering (a detection algorithm) of the simulated spectra. These results suggest that the metrics provide a reasonable summary of how the background emissivity and chemical absorbance interact to produce the at-sensor chemical signal. This study suggests that similarly effective predictors that account for more general physical conditions may be derived.« less

Physical quality characteristics of the microwave-dried breadfruit powders due to different processing conditions

NASA Astrophysics Data System (ADS)

Taruna, I.; Hakim, A. L.; Sutarsi

2018-03-01

Production of breadfruit powder has been an option to make easy its uses in various food processing. Accordingly, there is a need recently to apply advanced drying method, i.e. microwave drying, for improving quality since conventional methods produced highly variable product quality and required longer process. The present work was aimed to study the effect of microwave power and grinding time on physical quality of breadfruit powders. The experiment was done initially by drying breadfruit slices in a microwave dryer at power level of 420, 540, and 720 W and then grinding for 3, 5, and 7 min to get powdery product of less than 80 mesh. The physical quality of breadfruit powders were measured in terms of fineness modulus (FM), average particle size (D), whiteness (WI), total color difference (ΔE), water absorption (Wa), oil absorption (La), bulk density (ρb) and consistency gel (Gc). The results showed that physical quality of powders and its ranged-values included the FM (2.08-2.62), D (0.44-0.68 mm), WI (75.2-77.9), ΔE (7.4-10.5), Wa (5.5-6.2 ml/g), La (0.7-0.9 ml/g), ρb (0.62-0.70 g/cm3) and Gc (41.3-46.8 mm). The experiment revealed that variation of microwave power and grinding time affected significantly the quality of the breadfruit powders. However, microwave power was more dominant factor to affect quality of breadfruit powder in comparison to the grinding time.

Particle Sorting and Motility Out of Equilibrium

NASA Astrophysics Data System (ADS)

Sandford, Cato

The theory of equilibrium statistical physics, formulated over a century ago, provides an excellent description of physical systems which have reached a static, relaxed state. Such systems can be loosely thought of as maximally disordered, in keeping with the Second Law of Thermodynamics which states that a thermal system in equilibrium has reached a state of highest entropy. However, many entities in the world around us maintain themselves in an remarkably ordered and dynamic state, and must pay for this by producing entropy in their surroundings. Organisms, for example, convert chemical energy (food) into heat, which is then dumped into the environment, raising its entropy. Systems which produce entropy through any mechanism must be described by theories of non-equilibrium statistical physics, for which there currently exists no unified framework or ontology. Here we examine two specific cases of non-equilibrium phenomena from a theoretical perspective. First, we explore the behaviour of microscopic particles which continually dissipate energy to propel themselves through their environment. Second, we consider how devices which distinguish between different types of particles can exploit non-equilibrium processes to enhance their performance. For the case of self-propelled particles, we consider a theoretical model where the particle's propulsion force has "memory"--it is a random process whose instantaneous value depends on its past evolution. This introduces a persistence in the particle's motion, and requires the dissipation of energy into its surroundings. These particles are found to exhibit a variety of behaviours forbidden in equilibrium systems: for instance they may cluster around barriers, exert unbalanced forces, and sustain steady flows through space. We develop the understanding of these particles' dynamics through a combination of explicit calculations, approximations and numerical simulation which characterise and quantify their non-equilibrium behaviour. The second situation investigated concerns the physics of particle-sorting, which is fundamental to biological systems. We introduce a number of model devices designed to distinguish between and segregate two species of particles, and analyse how the quality and speed of their operation may be influenced by providing them with an energy source which pushes them out of equilibrium. We identify different physical regimes, where our devices may consume energy to deliver better results or deliver them faster or both; and we furthermore connect the broader theory of particle sorting to the fundamental theoretical framework of statistical physics.

Birefringent Stable Glass with Predominantly Isotropic Molecular Orientation

NASA Astrophysics Data System (ADS)

Liu, Tianyi; Exarhos, Annemarie L.; Alguire, Ethan C.; Gao, Feng; Salami-Ranjbaran, Elmira; Cheng, Kevin; Jia, Tiezheng; Subotnik, Joseph E.; Walsh, Patrick J.; Kikkawa, James M.; Fakhraai, Zahra

2017-09-01

Birefringence in stable glasses produced by physical vapor deposition often implies molecular alignment similar to liquid crystals. As such, it remains unclear whether these glasses share the same energy landscape as liquid-quenched glasses that have been aged for millions of years. Here, we produce stable glasses of 9-(3,5-di(naphthalen-1-yl)phenyl)anthracene molecules that retain three-dimensional shapes and do not preferentially align in a specific direction. Using a combination of angle- and polarization-dependent photoluminescence and ellipsometry experiments, we show that these stable glasses possess a predominantly isotropic molecular orientation while being optically birefringent. The intrinsic birefringence strongly correlates with increased density, showing that molecular ordering is not required to produce stable glasses or optical birefringence, and provides important insights into the process of stable glass formation via surface-mediated equilibration. To our knowledge, such novel amorphous packing has never been reported in the past.

Smart Optical Material Characterization System and Method

NASA Technical Reports Server (NTRS)

Choi, Sang Hyouk (Inventor); Park, Yeonjoon (Inventor)

2015-01-01

Disclosed is a system and method for characterizing optical materials, using steps and equipment for generating a coherent laser light, filtering the light to remove high order spatial components, collecting the filtered light and forming a parallel light beam, splitting the parallel beam into a first direction and a second direction wherein the parallel beam travelling in the second direction travels toward the material sample so that the parallel beam passes through the sample, applying various physical quantities to the sample, reflecting the beam travelling in the first direction to produce a first reflected beam, reflecting the beam that passes through the sample to produce a second reflected beam that travels back through the sample, combining the second reflected beam after it travels back though the sample with the first reflected beam, sensing the light beam produced by combining the first and second reflected beams, and processing the sensed beam to determine sample characteristics and properties.

The Coso geothermal area: A laboratory for advanced MEQ studies for geothermal monitoring

USGS Publications Warehouse

Julian, B.R.; Foulger, G.R.; Richards-Dinger, K.

2004-01-01

The permanent 16-station network of three-component digital seismometers at the Coso geothermal area, California, supplemented by 14 temporary instruments deployed in connection with the DOE Enhanced Geothermal Systems (EGS) Project, provides high-quality microearthquake (MEQ) recordings that are well suited to monitoring a producing geothermal area. We are currently using these data to investigate structure and active processes within the geothermal reservoir by applying three advanced methods: a) high-precision MEQ hypocenter location; b) time-dependent tomography; c) complete (moment tensor) MEQ source mechanism determination. Preliminary results to date resolve seismogenic structures in the producing field more clearly than is possible with conventional earthquake-location techniques. A shallow part of the producing field shows clear changes in the ratio of the seismic wave speeds, Vp/V s, between 1996 and 2002, which are probably related to physical changes in the reservoir caused by fluid extraction.

Long-term persistence of solar activity. [Abstract only

NASA Technical Reports Server (NTRS)

Ruzmaikin, Alexander; Feynman, Joan; Robinson, Paul

1994-01-01

The solar irradiance has been found to change by 0.1% over the recent solar cycle. A change of irradiance of about 0.5% is required to effect the Earth's climate. How frequently can a variation of this size be expected? We examine the question of the persistence of non-periodic variations in solar activity. The Huerst exponent, which characterizes the persistence of a time series (Mandelbrot and Wallis, 1969), is evaluated for the series of C-14 data for the time interval from about 6000 BC to 1950 AD (Stuiver and Pearson, 1986). We find a constant Huerst exponent, suggesting that solar activity in the frequency range of from 100 to 3000 years includes an important continuum component in addition to the well-known periodic variations. The value we calculate, H approximately equal to 0.8, is significantly larger than the value of 0.5 that would correspond to variations produced by a white-noise process. This value is in good agreement with the results for the monthly sunspot data reported elsewhere, indicating that the physics that produces the continuum is a correlated random process (Ruzmaikin et al., 1992), and that is is the same type of process over a wide range of time interval lengths. We conclude that the time period over which an irradiance change of 0.5% can be expected to occur is significantly shorter than that which would be expected for variations produced by a white-noise process.

Rapidly dissolving repaglinide powders produced by the ultra-rapid freezing process.

PubMed

Purvis, Troy; Mattucci, Michal E; Crisp, M Todd; Johnston, Keith P; Williams, Robert O

2007-07-20

The objective of the study was to produce rapidly dissolving formulations of the poorly water-soluble drug repaglinide using an innovative new technology, ultra-rapid freezing (URF), and to investigate the influence of excipient type on repaglinide stability. Repaglinide compositions containing different types and levels of excipients and different drug potencies (50%-86%) were produced by the URF technology. Repaglinide/excipient solutions were frozen on a cryogenic substrate, collected, and lyophilized to form a dry powder. Surfactants, including sodium dodecyl sulfate, and alkalizing agents such as diethanolamine (DEA) and tromethamine (TRIS) were incorporated into the compositions. Forced degradation of repaglinide was conducted under stressed conditions (eg, elevated temperature, exposure to peroxide) to determine the stability of the drug in such environments. The solubility of repaglinide increased as a function of increasing pH; therefore, incorporation of an alkalizing agent into the URF formulations increased the drug's solubility. Drug instability resulted when the drug was exposed to pH values above 9.0. URF formulations containing alkalizing agents showed no degradation or spontaneous recrystallization in the formulation, indicating that increased stability was afforded by processing. URF processing created nanostructured drug/excipient particles with higher dissolution rates than were achieved for unprocessed drug. Alkalizing agents such as TRIS and DEA, present at levels of 25% to 33% wt/wt in the formulations, did not cause degradation of the drug when processed using URF. URF processing, therefore, yielded fast-dissolving formulations that were physically and chemically stable, resistant to alkali degradation or spontaneous recrystallization in the formulation.

Optimisation des proprietes physiques d'un composite carbone epoxy fabrique par le procede RFI

NASA Astrophysics Data System (ADS)

Koanda, Mahamat Mamadou Lamine

The RFI (Resin Film Infusion) process is a composite materials manufacturing process. Especially known for the small investment it requires, RFI processes are more and more widely used in the aeronautical industry. However a number of aspects of this process are still not well controlled. The quality of the final part depends on which process is used. In the case of RFI, controlling physical characteristics such as thickness, fiber volume fraction or void content remains a major challenge. This dissertation deals with the optimization of the physical properties of a carbon composite manufactured with RFI processes. The ASTMD3171 and ASTMD792 standards were used to measure the void content and fiber volume fraction. First, we introduced different layup sequences in the RFI process and evaluate their impact on the physical properties of the final product. The experiments show the primary mode A, with the resin film at the bottom, resulting in much better quality with controlled fiber volume fraction and void content. Mode B (film in the symmetrical plane) yields results identical to mode A except more irregular thicknesses. Mode C (symmetrical film in the laminate) produces locally unacceptable void contents. Mode D (resin film on the top of the laminate) yields much better results than mode A with the exception of the more irregular thicknesses. Making gaps and overlaps with the resin film has negative effects beyond 2.54cm (one inch) and should be avoided. Several C-scan observations of the manufactured samples showed a large accumulation of porosity in the resin rich areas, as well as surface defects. Ultimately we analyzed the cure cycle in light of the thermodynamic porosity models. It is evident that the diffusion phenomenon is essential in this process. Therefore a better conditioning of the resin film made by Cytec is required. An optimal design with a cycle stop and pressure lag yields the optimal cure cycle for the RFI process.

A Study of Heavy Precipitation Events in Taiwan During 10-13 August, 1994. Part 2; Mesoscale Model Simulations

NASA Technical Reports Server (NTRS)

Tao, Wei Kuo; Chen, C.-S.; Jia, Y.; Baker, D.; Lang, S.; Wetzel, P.; Lau, W. K.-M.

2001-01-01

Several heavy precipitation episodes occurred over Taiwan from August 10 to 13, 1994. Precipitation patterns and characteristics are quite different between the precipitation events that occurred from August 10 and I I and from August 12 and 13. In Part I (Chen et al. 2001), the environmental situation and precipitation characteristics are analyzed using the EC/TOGA data, ground-based radar data, surface rainfall patterns, surface wind data, and upper air soundings. In this study (Part II), the Penn State/NCAR Mesoscale Model (MM5) is used to study the precipitation characteristics of these heavy precipitation events. Various physical processes (schemes) developed at NASA Goddard Space Flight Center (i.e., cloud microphysics scheme, radiative transfer model, and land-soil-vegetation surface model) have recently implemented into the MM5. These physical packages are described in the paper, Two way interactive nested grids are used with horizontal resolutions of 45, 15 and 5 km. The model results indicated that Cloud physics, land surface and radiation processes generally do not change the location (horizontal distribution) of heavy precipitation. The Goddard 3-class ice scheme produced more rainfall than the 2-class scheme. The Goddard multi-broad-band radiative transfer model reduced precipitation compared to a one-broad band (emissivity) radiation model. The Goddard land-soil-vegetation surface model also reduce the rainfall compared to a simple surface model in which the surface temperature is computed from a Surface energy budget following the "force-re store" method. However, model runs including all Goddard physical processes enhanced precipitation significantly for both cases. The results from these runs are in better agreement with observations. Despite improved simulations using different physical schemes, there are still some deficiencies in the model simulations. Some potential problems are discussed. Sensitivity tests (removing either terrain or radiative processes) are performed to identify the physical processes that determine the precipitation patterns and characteristics for heavy rainfall events. These sensitivity tests indicated that terrain can play a major role in determining the exact location for both precipitation events. The terrain can also play a major role in determining the intensity of precipitation for both events. However, it has a large impact on one event but a smaller one on the other. The radiative processes are also important for determining, the precipitation patterns for one case but. not the other. The radiative processes can also effect the total rainfall for both cases to different extents.

Effect of processing parameters and pore structure of nanostructured silica aerogel on the physical properties of aerogel blankets

NASA Astrophysics Data System (ADS)

Latifi, Fatemeh; Talebi, Zahra; Khalili, Haleh; Zarrebini, Mohammad

2018-05-01

This work investigates the influence of processing parameters and aerogel pore structure on the physical properties and hydrophobicity of aerogel blankets. Aerogel blankets were produced by in situ synthesis of nanostructured silica aerogel on a polyester nonwoven substrate. Nitrogen adsorption-desorption analysis, contact angle test and FE-SEM images were used to characterize both the aerogel particles and the blankets. The results showed that the weight and thickness of the blanket were reduced when the low amount of catalyst was used. A decrease in the aerogel pore size from 22 to 11 nm increased the weight and thickness of the blankets. The xerogel particles with high density and pore size of 5 nm reduced the blanket weight. Also, the blanket weight and thickness were increased due to increasing the sol volume. It was found that the hydrophobicity of aerogel blankets is not influenced by sol volume and pore structure of silica aerogel.

Electrostatic Assist of Liquid Transfer in Printing Processes

NASA Astrophysics Data System (ADS)

Huang, Chung-Hsuan; Kumar, Satish

2016-11-01

Transfer of liquid from one surface to another plays an important role in many printing processes. Incomplete liquid transfer can produce defects that are detrimental to the operation of printed electronic devices, and one strategy for minimizing these defects is to apply an electric field, a technique known as electrostatic assist (ESA). However, the underlying physical mechanisms of ESA remain a mystery. To better understand these mechanisms, slender-jet models for both perfect dielectric and leaky dielectric Newtonian liquid bridges with moving contact lines are developed. Nonlinear partial differential equations describing the time- and axial-evolution of the bridge radius and interfacial charge are derived, and then solved using finite-element methods. For perfect dielectrics, it is found that application of an electric field enhances transfer of liquid to the more wettable surface. For leaky dielectrics, application of an electric field can augment or oppose the influence of wettability differences, depending on the direction of the electric field and the sign of the interfacial charge. The physical mechanisms underlying these observations will be discussed.

A Hands-on Physical Analog Demonstration of Real-Time Volcano Deformation Monitoring with GNSS/GPS

NASA Astrophysics Data System (ADS)

Jones, J. R.; Schobelock, J.; Nguyen, T. T.; Rajaonarison, T. A.; Malloy, S.; Njinju, E. A.; Guerra, L.; Stamps, D. S.; Glesener, G. B.

2017-12-01

Teaching about volcano deformation and how scientists study these processes using GNSS/GPS may present some challenge since the volcanoes and/or GNSS/GPS equipment are not quite accessible to most teachers. Educators and curriculum materials specialists have developed and shared a number of activities and demonstrations to help students visualize volcanic processes and ways scientist use GNSS/GPS in their research. From resources provided by MEDL (the Modeling and Educational Demonstrations Laboratory) in the Department of Geosciences at Virginia Tech, we combined multiple materials and techniques from these previous works to produce a hands-on physical analog model from which students can learn about GNSS/GPS studies of volcano deformation. The model functions as both a qualitative and quantitative learning tool with good analogical affordances. In our presentation, we will describe multiple ways of teaching with the model, what kinds of materials can be used to build it, and ways we think the model could be enhanced with the addition of Vernier sensors for data collection.

Construction material processed using lunar simulant in various environments

NASA Technical Reports Server (NTRS)

Chase, Stan; Ocallaghan-Hay, Bridget; Housman, Ralph; Kindig, Michael; King, John; Montegrande, Kevin; Norris, Raymond; Vanscotter, Ryan; Willenborg, Jonathan; Staubs, Harry

1995-01-01

The manufacture of construction materials from locally available resources in space is an important first step in the establishment of lunar and planetary bases. The objective of the CoMPULSIVE (Construction Material Processed Using Lunar Simulant In Various Environments) experiment is to develop a procedure to produce construction materials by sintering or melting Johnson Space Center Simulant 1 (JSC-1) lunar soil simulant in both earth-based (1-g) and microgravity (approximately 0-g) environments. The characteristics of the resultant materials will be tested to determine its physical and mechanical properties. The physical characteristics include: crystalline, thermal, and electrical properties. The mechanical properties include: compressive tensile, and flexural strengths. The simulant, placed in a sealed graphite crucible, will be heated using a high temperature furnace. The crucible will then be cooled by radiative and forced convective means. The core furnace element consists of space qualified quartz-halogen incandescent lamps with focusing mirrors. Sample temperatures of up to 2200 C are attainable using this heating method.

A Dynamical Systems Explanation of the Hurst Effect and Atmospheric Low-Frequency Variability

PubMed Central

Franzke, Christian L. E.; Osprey, Scott M.; Davini, Paolo; Watkins, Nicholas W.

2015-01-01

The Hurst effect plays an important role in many areas such as physics, climate and finance. It describes the anomalous growth of range and constrains the behavior and predictability of these systems. The Hurst effect is frequently taken to be synonymous with Long-Range Dependence (LRD) and is typically assumed to be produced by a stationary stochastic process which has infinite memory. However, infinite memory appears to be at odds with the Markovian nature of most physical laws while the stationarity assumption lacks robustness. Here we use Lorenz's paradigmatic chaotic model to show that regime behavior can also cause the Hurst effect. By giving an alternative, parsimonious, explanation using nonstationary Markovian dynamics, our results question the common belief that the Hurst effect necessarily implies a stationary infinite memory process. We also demonstrate that our results can explain atmospheric variability without the infinite memory previously thought necessary and are consistent with climate model simulations. PMID:25765880

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larson, Natalie M.; Zok, Frank W.

One route for producing fiber-reinforced ceramic-matrix composites entails repeated impregnation and pyrolysis of a preceramic polymer in a fiber preform. The process relies crucially on the development of networks of contiguous cracks during pyrolysis, thereby allowing further impregnation to attain nearly-full densification. The present study employs in-situ x-ray computed tomography (XCT) to reveal in three dimensions the evolution of matrix structure during pyrolysis of a SiC-based preceramic polymer to 1200 °C. Observations are used to guide the development of a taxonomy of crack geometries and crack structures and to identify the temporal sequence of their formation. A quantitative analysis ismore » employed to characterize effects of local microstructural dimensions on the conditions required to form cracks of various types. Complementary measurements of gas evolution and mass loss of the preceramic polymer during pyrolysis as well as changes in mass density and Young's modulus provide context for the physical changes revealed by XCT. Furthermore, the findings provide a foundation for future development of physics-based models to guide composite fabrication processes.« less

Microstructural Characterization of Semi-Interpenetrating Polymer Networks by Positron Lifetime Spectroscopy

NASA Technical Reports Server (NTRS)

Singh, Jag J.; Pater, Ruth H.; Eftekhari, Abe

1996-01-01

Thermoset and thermoplastic polyimides have complementary physical and mechanical properties. Whereas thermoset polyimides are brittle and generally easier to process, thermoplastic polyimides are tough but harder to process. A combination of these two types of polyimides may help produce polymers more suitable for aerospace applications. Semi-Interpenetrating Polymer Networks (S-IPN) of thermoset LaRC(TM)-RP46 and thermoplastic LaRC(TM)-IA polyimides were prepared in weight percent ratios ranging from 100:0 to 0:100. Positron lifetime measurements were made in these samples to correlate their free volume features with physical and mechanical properties. As expected, positronium atoms are not formed in these samples. The second lifetime component has been used to infer the positron trap dimensions. The 'free volume' goes through a minimum at a ratio of about 50:50, and this suggests that S-IPN samples are not merely solid solutions of the two polymers. These data and related structural properties of the S-IPN samples are discussed.

Massively Parallel Real-Time TDDFT Simulations of Electronic Stopping Processes

NASA Astrophysics Data System (ADS)

Yost, Dillon; Lee, Cheng-Wei; Draeger, Erik; Correa, Alfredo; Schleife, Andre; Kanai, Yosuke

Electronic stopping describes transfer of kinetic energy from fast-moving charged particles to electrons, producing massive electronic excitations in condensed matter. Understanding this phenomenon for ion irradiation has implications in modern technologies, ranging from nuclear reactors, to semiconductor devices for aerospace missions, to proton-based cancer therapy. Recent advances in high-performance computing allow us to achieve an accurate parameter-free description of these phenomena through numerical simulations. Here we discuss results from our recently-developed large-scale real-time TDDFT implementation for electronic stopping processes in important example materials such as metals, semiconductors, liquid water, and DNA. We will illustrate important insight into the physics underlying electronic stopping and we discuss current limitations of our approach both regarding physical and numerical approximations. This work is supported by the DOE through the INCITE awards and by the NSF. Part of this work was performed under the auspices of U.S. DOE by LLNL under Contract DE-AC52-07NA27344.

Coupling of a distributed stakeholder-built system dynamics socio-economic model with SAHYSMOD for sustainable soil salinity management - Part 1: Model development

NASA Astrophysics Data System (ADS)

Inam, Azhar; Adamowski, Jan; Prasher, Shiv; Halbe, Johannes; Malard, Julien; Albano, Raffaele

2017-08-01

Effective policies, leading to sustainable management solutions for land and water resources, require a full understanding of interactions between socio-economic and physical processes. However, the complex nature of these interactions, combined with limited stakeholder engagement, hinders the incorporation of socio-economic components into physical models. The present study addresses this challenge by integrating the physical Spatial Agro Hydro Salinity Model (SAHYSMOD) with a participatory group-built system dynamics model (GBSDM) that includes socio-economic factors. A stepwise process to quantify the GBSDM is presented, along with governing equations and model assumptions. Sub-modules of the GBSDM, describing agricultural, economic, water and farm management factors, are linked together with feedbacks and finally coupled with the physically based SAHYSMOD model through commonly used tools (i.e., MS Excel and a Python script). The overall integrated model (GBSDM-SAHYSMOD) can be used to help facilitate the role of stakeholders with limited expertise and resources in model and policy development and implementation. Following the development of the integrated model, a testing methodology was used to validate the structure and behavior of the integrated model. Model robustness under different operating conditions was also assessed. The model structure was able to produce anticipated real behaviours under the tested scenarios, from which it can be concluded that the formulated structures generate the right behaviour for the right reasons.

Novel Plasmonic and Hyberbolic Optical Materials for Control of Quantum Nanoemitters

DTIC Science & Technology

2016-12-08

properties, metal ion implantation techniques, and multi- physics modeling to produce hyperbolic quantum nanoemitters. 15. SUBJECT TERMS nanotechnology 16...techniques, and multi- physics modeling to produce hyperbolic quantum nanoemitters. During the course of this project we studied plasmonic

Optical spectroscopy of laser-produced plasmas for standoff isotopic analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harilal, Sivanandan S.; Brumfield, Brian E.; LaHaye, Nicole L.

2018-04-20

This review article covers the present status of isotope detection through emission, absorption, and fluorescence spectroscopy of atoms and molecules in a laser-produced plasma formed from a solid sample. A description of the physics behind isotope shifts in atoms and molecules is presented, followed by the physics behind solid sampling of laser ablation plumes, optical methods for isotope measurements, the suitable physical conditions of laser-produced plasma plumes for isotopic analysis, and the current status. Finally, concluding remarks will be made on the existing gaps between previous works in the literature and suggestions for future work.

Optical spectroscopy of laser-produced plasmas for standoff isotopic analysis

DOE PAGES

Harilal, S. S.; Brumfield, B. E.; LaHaye, N. L.; ...

2018-04-20

This review article covers the present status of isotope detection through emission, absorption, and fluorescence spectroscopy of atoms and molecules in a laser-produced plasma formed from a solid sample. A description of the physics behind isotope shifts in atoms and molecules is presented, followed by the physics behind solid sampling of laser ablation plumes, optical methods for isotope measurements, the suitable physical conditions of laser-produced plasma plumes for isotopic analysis, and the current status. Lastly, concluding remarks will be made on the existing gaps between previous works in the literature and suggestions for future work.

Optical spectroscopy of laser-produced plasmas for standoff isotopic analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harilal, S. S.; Brumfield, B. E.; LaHaye, N. L.

This review article covers the present status of isotope detection through emission, absorption, and fluorescence spectroscopy of atoms and molecules in a laser-produced plasma formed from a solid sample. A description of the physics behind isotope shifts in atoms and molecules is presented, followed by the physics behind solid sampling of laser ablation plumes, optical methods for isotope measurements, the suitable physical conditions of laser-produced plasma plumes for isotopic analysis, and the current status. Finally, concluding remarks will be made on the existing gaps between previous works in the literature and suggestions for future work.

Optical spectroscopy of laser-produced plasmas for standoff isotopic analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harilal, S. S.; Brumfield, B. E.; LaHaye, N. L.

This review article covers the present status of isotope detection through emission, absorption, and fluorescence spectroscopy of atoms and molecules in a laser-produced plasma formed from a solid sample. A description of the physics behind isotope shifts in atoms and molecules is presented, followed by the physics behind solid sampling of laser ablation plumes, optical methods for isotope measurements, the suitable physical conditions of laser-produced plasma plumes for isotopic analysis, and the current status. Lastly, concluding remarks will be made on the existing gaps between previous works in the literature and suggestions for future work.

Optical spectroscopy of laser-produced plasmas for standoff isotopic analysis

DOE PAGES

Harilal, S. S.; Brumfield, B. E.; LaHaye, N. L.; ...

2018-06-01

This review article covers the present status of isotope detection through emission, absorption, and fluorescence spectroscopy of atoms and molecules in a laser-produced plasma formed from a solid sample. A description of the physics behind isotope shifts in atoms and molecules is presented, followed by the physics behind solid sampling of laser ablation plumes, optical methods for isotope measurements, the suitable physical conditions of laser-produced plasma plumes for isotopic analysis, and the current status. Finally, concluding remarks will be made on the existing gaps between previous works in the literature and suggestions for future work.

Transparent electrical conducting films by activated reactive evaporation

DOEpatents

Bunshah, Rointan; Nath, Prem

1982-01-01

Process and apparatus for producing transparent electrical conducting thin films by activated reactive evaporation. Thin films of low melting point metals and alloys, such as indium oxide and indium oxide doped with tin, are produced by physical vapor deposition. The metal or alloy is vaporized by electrical resistance heating in a vacuum chamber, oxygen and an inert gas such as argon are introduced into the chamber, and vapor and gas are ionized by a beam of low energy electrons in a reaction zone between the resistance heater and the substrate. There is a reaction between the ionized oxygen and the metal vapor resulting in the metal oxide which deposits on the substrate as a thin film which is ready for use without requiring post deposition heat treatment.

Production of coloured glass-ceramics from incinerator ash using thermal plasma technology.

PubMed

Cheng, T W; Huang, M Z; Tzeng, C C; Cheng, K B; Ueng, T H

2007-08-01

Incineration is a major treatment process for municipal solid waste in Taiwan. It is estimated that over 1.5 Mt of incinerator ash are produced annually. This study proposes using thermal plasma technology to treat incinerator ash. Sintered glass-ceramics were produced using quenched vitrified slag with colouring agents added. The experimental results showed that the major crystalline phases developed in the sintered glass-ceramics were gehlenite and wollastonite, but many other secondary phases also appeared depending on the colouring agents added. The physical/mechanical properties, chemical resistance and toxicity characteristic leaching procedure of the coloured glass-ceramics were satisfactory. The glass-ceramic products obtained from incinerator ash treated with thermal plasma technology have great potential for building applications.

Using X-ray spectroscopy of relativistic laser plasma interaction to reveal parametric decay instabilities: a modeling tool for astrophysics.

PubMed

Oks, E; Dalimier, E; Faenov, A Ya; Angelo, P; Pikuz, S A; Tubman, E; Butler, N M H; Dance, R J; Pikuz, T A; Skobelev, I Yu; Alkhimova, M A; Booth, N; Green, J; Gregory, C; Andreev, A; Zhidkov, A; Kodama, R; McKenna, P; Woolsey, N

2017-02-06

By analyzing profiles of experimental x-ray spectral lines of Si XIV and Al XIII, we found that both Langmuir and ion acoustic waves developed in plasmas produced via irradiation of thin Si foils by relativistic laser pulses (intensities ~10²¹ W/cm²). We prove that these waves are due to the parametric decay instability (PDI). This is the first time that the PDI-induced ion acoustic turbulence was discovered by the x-ray spectroscopy in laser-produced plasmas. These conclusions are also supported by PIC simulations. Our results can be used for laboratory modeling of physical processes in astrophysical objects and a better understanding of intense laser-plasma interactions.

Shatter cones - An outstanding problem in shock mechanics. [geological impact fracture surface in cratering

NASA Technical Reports Server (NTRS)

Milton, D. J.

1977-01-01

Shatter cone characteristics are surveyed. Shatter cones, a form of rock fracture in impact structures, apparently form as a shock front interacts with inhomogeneities or discontinuities in the rock. Topics discussed include morphology, conditions of formation, shock pressure of formation, and theories of formation. It is thought that shatter cones are produced within a limited range of shock pressures extending from about 20 to perhaps 250 kbar. Apical angles range from less than 70 deg to over 120 deg. Tentative hypotheses concerning the physical process of shock coning are considered. The range in shock pressures which produce shatter cones might correspond to the range in which shock waves decompose into elastic and deformational fronts.

Bat noseleaf model: echolocation function, design considerations, and experimental verification.

PubMed

Kuc, Roman

2011-05-01

This paper describes a possible bat noseleaf echolocation function that improves target elevation resolution. Bats with a protruding noseleaf can rotate the lancet to act as an acoustic mirror that reflects the nostril emission, modeled as a virtual nostril that produces a delayed emission. The cancellation of the nostril and virtual nostril components at a target produces a sharp spectral notch whose frequency location relates to target elevation. This notch can be observed directly from the swept-frequency emission waveform, suggesting cochlear processing capabilities. Physical acoustic principles indicate the design considerations and trade-offs that a bat can accomplish through noseleaf shape and emission characteristics. An experimental model verifies the analysis and exhibits an elevation versus notch frequency sensitivity of approximately 1°/kHz.

Exopolysaccharides enriched in rare sugars: bacterial sources, production, and applications.

PubMed

Roca, Christophe; Alves, Vitor D; Freitas, Filomena; Reis, Maria A M

2015-01-01

Microbial extracellular polysaccharides (EPS), produced by a wide range of bacteria, are high molecular weight biopolymers, presenting an extreme diversity in terms of chemical structure and composition. They may be used in many applications, depending on their chemical and physical properties. A rather unexplored aspect is the presence of rare sugars in the composition of some EPS. Rare sugars, such as rhamnose or fucose, may provide EPS with additional biological properties compared to those composed of more common sugar monomers. This review gives a brief overview of these specific EPS and their producing bacteria. Cultivation conditions are summarized, demonstrating their impact on the EPS composition, together with downstream processing. Finally, their use in different areas, including cosmetics, food products, pharmaceuticals, and biomedical applications, are discussed.

Explosive Welding in the 1990's

NASA Technical Reports Server (NTRS)

Lalwaney, N. S.; Linse, V. D.

1985-01-01

Explosive bonding is a unique joining process with the serious potential to produce composite materials capable of fulfilling many of the high performance materials capable of fulfilling many of the high performance materials needs of the 1990's. The process has the technological versatility to provide a true high quality metallurgical compatible and incompatible systems. Metals routinely explosively bonded include a wide variety of combinations of reactive and refractory metals, low and high density metals and their alloys, corrosion resistant and high strength alloys, and common steels. The major advantage of the process is its ability to custom design and engineer composites with physical and/or mechanical properties that meet a specific or unusual performance requirement. Explosive bonding offers the designer unique opportunities in materials selection with unique combinations of properties and high integrity bonds that cannot be achieved by any other metal joining process. The process and some applications are discussed.

Production of Low Cost Carbon-Fiber through Energy Optimization of Stabilization Process.

PubMed

Golkarnarenji, Gelayol; Naebe, Minoo; Badii, Khashayar; Milani, Abbas S; Jazar, Reza N; Khayyam, Hamid

2018-03-05

To produce high quality and low cost carbon fiber-based composites, the optimization of the production process of carbon fiber and its properties is one of the main keys. The stabilization process is the most important step in carbon fiber production that consumes a large amount of energy and its optimization can reduce the cost to a large extent. In this study, two intelligent optimization techniques, namely Support Vector Regression (SVR) and Artificial Neural Network (ANN), were studied and compared, with a limited dataset obtained to predict physical property (density) of oxidative stabilized PAN fiber (OPF) in the second zone of a stabilization oven within a carbon fiber production line. The results were then used to optimize the energy consumption in the process. The case study can be beneficial to chemical industries involving carbon fiber manufacturing, for assessing and optimizing different stabilization process conditions at large.

Production of Low Cost Carbon-Fiber through Energy Optimization of Stabilization Process

PubMed Central

Golkarnarenji, Gelayol; Naebe, Minoo; Badii, Khashayar; Milani, Abbas S.; Jazar, Reza N.; Khayyam, Hamid

2018-01-01

To produce high quality and low cost carbon fiber-based composites, the optimization of the production process of carbon fiber and its properties is one of the main keys. The stabilization process is the most important step in carbon fiber production that consumes a large amount of energy and its optimization can reduce the cost to a large extent. In this study, two intelligent optimization techniques, namely Support Vector Regression (SVR) and Artificial Neural Network (ANN), were studied and compared, with a limited dataset obtained to predict physical property (density) of oxidative stabilized PAN fiber (OPF) in the second zone of a stabilization oven within a carbon fiber production line. The results were then used to optimize the energy consumption in the process. The case study can be beneficial to chemical industries involving carbon fiber manufacturing, for assessing and optimizing different stabilization process conditions at large. PMID:29510592

Literature review on production process to obtain extra virgin olive oil enriched in bioactive compounds. Potential use of byproducts as alternative sources of polyphenols.

PubMed

Frankel, Edwin; Bakhouche, Abdelhakim; Lozano-Sánchez, Jesús; Segura-Carretero, Antonio; Fernández-Gutiérrez, Alberto

2013-06-05

This review describes the olive oil production process to obtain extra virgin olive oil (EVOO) enriched in polyphenol and byproducts generated as sources of antioxidants. EVOO is obtained exclusively by mechanical and physical processes including collecting, washing, and crushing of olives, malaxation of olive paste, centrifugation, storage, and filtration. The effect of each step is discussed to minimize losses of polyphenols from large quantities of wastes. Phenolic compounds including phenolic acids, alcohols, secoiridoids, lignans, and flavonoids are characterized in olive oil mill wastewater, olive pomace, storage byproducts, and filter cake. Different industrial pilot plant processes are developed to recover phenolic compounds from olive oil byproducts with antioxidant and bioactive properties. The technological information compiled in this review will help olive oil producers to improve EVOO quality and establish new processes to obtain valuable extracts enriched in polyphenols from byproducts with food ingredient applications.

Estimation of the processes controlling variability in phytoplankton pigment distributions on the southeastern U.S. continental shelf

NASA Technical Reports Server (NTRS)

Mcclain, Charles R.; Ishizaka, Joji; Hofmann, Eileen E.

1990-01-01

Five coastal-zone-color-scanner images from the southeastern U.S. continental shelf are combined with concurrent moored current meter measurements to assess the processes controlling the variability in chlorophyll concentration and distribution in this region. An equation governing the space and time distribution of a nonconservative quantity such as chlorophyll is used in the calculations. The terms of the equation, estimated from observations, show that advective, diffusive, and local processes contribute to the plankton distributions and vary with time and location. The results from this calculation are compared with similar results obtained using a numerical physical-biological model with circulation fields derived from an optimal interpolation of the current meter observations and it is concluded that the two approaches produce different estimates of the processes controlling phytoplankton variability.

Preface: MHD wave phenomena in the solar interior and atmosphere

NASA Astrophysics Data System (ADS)

Fedun, Viktor; Srivastava, A. K.

2018-01-01

The Sun is our nearest star and this star produces various plasma wave processes and energetic events. These phenomena strongly influence interplanetary plasma dynamics and contribute to space-weather. The understanding of solar atmospheric dynamics requires hi-resolution modern observations which, in turn, further advances theoretical models of physical processes in the solar interior and atmosphere. In particular, it is essential to connect the magnetohydrodynamic (MHD) wave processes with the small and large-scale solar phenomena vis-a-vis transport of energy and mass. With the advent of currently available and upcoming high-resolution space (e.g., IRIS, SDO, Hinode, Aditya-L1, Solar-C, Solar Orbiter), and ground-based (e.g., SST, ROSA, NLST, Hi-C, DKIST, EST, COSMO) observations, solar physicists are able to explore exclusive wave processes in various solar magnetic structures at different spatio-temporal scales.

Impact Cratering Calculations

NASA Technical Reports Server (NTRS)

Ahrens, Thomas J.

2001-01-01

This research is computational /theoretical and complements the Caltech experimental program. We have developed an understanding of the basic physical processes and produced computational models and implemented these into Eulerian and Lagrangian finite element codes. The key issues we have addressed include the conditions required for: faulting (strain localization), elastic moduli weakening, dynamic weakening (layering elastic instabilities and fluidization), bulking (creation of porosity at zero pressure) and compaction of pores, frictional melting (creation of pseudotachylytes), partial and selective devolatilization of materials (e.g. CaCO3, water/ice mixtures), and debris flows.

Ionic Liquids and Cellulose: Dissolution, Chemical Modification and Preparation of New Cellulosic Materials

PubMed Central

Isik, Mehmet; Sardon, Haritz; Mecerreyes, David

2014-01-01

Due to its abundance and a wide range of beneficial physical and chemical properties, cellulose has become very popular in order to produce materials for various applications. This review summarizes the recent advances in the development of new cellulose materials and technologies using ionic liquids. Dissolution of cellulose in ionic liquids has been used to develop new processing technologies, cellulose functionalization methods and new cellulose materials including blends, composites, fibers and ion gels. PMID:25000264

Editorial Commentary: Paving a Road Requires a Well-Mixed Cement Stem Cells, Platelet-Rich Plasma, and Shoulder Rotator Cuff Healing.

PubMed

Maffulli, Nicola

2018-03-01

The process of healing in musculoskeletal tissues is complex, and the addition of devices, including platelet-rich plasma and mesenchymal stem cells, to biologically enhance it may favor its optimization. This work shows in a compelling fashion that it is possible to produce the right admixture of physical and biological factors to make it happen in rotator cuff repair. Copyright © 2017 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Anisotropy and Microstructure of High-Coercivity Rare Earth Iron Permanent Magnets

DTIC Science & Technology

1989-06-01

still necessary in order to achieve a high quality permanent magnet with an opera - ting temperature up to 150C. Acces1O, FO" NTIS CRA&i DTIC TAB... China , Crucible Materials and Unocal, USA) under different processing and post-sintering heat treatment conditions. Doped, "two-phase" Nd:0FebaiBe...mation for the nucleation field Ho (8,10). -15- 4.5 Al-substituted magnets These sintered magnets were produced by the Institute of Physics in Bejing

An In-Depth Review on Direct Additive Manufacturing of Metals

NASA Astrophysics Data System (ADS)

Azam, Farooq I.; Rani, Ahmad Majdi Abdul; Altaf, Khurram; Rao, T. V. V. L. N.; Aimi Zaharin, Haizum

2018-03-01

Additive manufacturing (AM), also known as 3D Printing, is a revolutionary manufacturing technique which has been developing rapidly in the last 30 years. The evolution of this precision manufacturing process from rapid prototyping to ready-to-use parts has significantly alleviated manufacturing constraints and design freedom has been outstandingly widened. AM is a non-conventional manufacturing technique which utilizes a 3D CAD model data to build parts by adding one material layer at a time, rather than removing it and fulfills the demand for manufacturing parts with complex geometric shapes, great dimensional accuracy, and easy to assemble parts. Additive manufacturing of metals has become the area of extensive research, progressing towards the production of final products and replacing conventional manufacturing methods. This paper provides an insight to the available metal additive manufacturing technologies that can be used to produce end user products without using conventional manufacturing methods. The paper also includes the comparison of mechanical and physical properties of parts produced by AM with the parts manufactured using conventional processes.

Virtual and super - virtual refraction method: Application to synthetic data and 2012 of Karangsambung survey data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nugraha, Andri Dian; Adisatrio, Philipus Ronnie

2013-09-09

Seismic refraction survey is one of geophysical method useful for imaging earth interior, definitely for imaging near surface. One of the common problems in seismic refraction survey is weak amplitude due to attenuations at far offset. This phenomenon will make it difficult to pick first refraction arrival, hence make it challenging to produce the near surface image. Seismic interferometry is a new technique to manipulate seismic trace for obtaining Green's function from a pair of receiver. One of its uses is for improving first refraction arrival quality at far offset. This research shows that we could estimate physical properties suchmore » as seismic velocity and thickness from virtual refraction processing. Also, virtual refraction could enhance the far offset signal amplitude since there is stacking procedure involved in it. Our results show super - virtual refraction processing produces seismic image which has higher signal-to-noise ratio than its raw seismic image. In the end, the numbers of reliable first arrival picks are also increased.« less

Biogeochemistry and limnology in Antarctic subglacial weathering: molecular evidence of the linkage between subglacial silica input and primary producers in a perennially ice-covered lake

NASA Astrophysics Data System (ADS)

Takano, Yoshinori; Kojima, Hisaya; Takeda, Eriko; Yokoyama, Yusuke; Fukui, Manabu

2015-12-01

We report a 6,000 years record of subglacial weathering and biogeochemical processes in two perennially ice-covered glacial lakes at Rundvågshetta, on the Soya Coast of Lützow-Holm Bay, East Antarctica. The two lakes, Lake Maruwan Oike and Lake Maruwan-minami, are located in a channel that drains subglacial water from the base of the East Antarctic ice sheet. Greenish-grayish organic-rich laminations in sediment cores from the lakes indicate continuous primary production affected by the inflow of subglacial meltwater containing relict carbon, nitrogen, sulfur, and other essential nutrients. Biogenic silica, amorphous hydrated silica, and DNA-based molecular signatures of sedimentary facies indicate that diatom assemblages are the dominant primary producers, supported by the input of inorganic silicon (Si) from the subglacial inflow. This study highlights the significance of subglacial water-rock interactions during physical and chemical weathering processes and the importance of such interactions for the supply of bioavailable nutrients.

Effect of Power Ultrasound on Food Quality

NASA Astrophysics Data System (ADS)

Lee, Hyoungill; Feng, Hao

Recent food processing technology innovations have been centered around producing foods with fresh-like attributes through minimal processing or nonthermal processing technologies. Instead of using thermal energy to secure food safety that is often accompanied by quality degradation in processed foods, the newly developed processing modalities utilize other types of physical energy such as high pressure, pulsed electric field or magnetic field, ultraviolet light, or acoustic energy to process foods. An improvement in food quality by the new processing methods has been widely reported. In comparison with its low-energy (high-frequency) counterpart which finds applications in food quality inspection, the use of high-intensity ultrasound, also called power ultrasound, in food processing is a relatively new endeavor. To understand the effect of high-intensity ultrasound treatment on food quality, it is important to understand the interactions between acoustic energy and food ingredients, which is covered in Chapter 10. In this chapter, the focus will be on changes in overall food quality attributes that are caused by ultrasound, such as texture, color, flavor, and nutrients.

Calorimetry of electron beams and the calibration of dosimeters at high doses

NASA Astrophysics Data System (ADS)

Humphreys, J. C.; McLaughlin, W. L.

Graphite or metal calorimeters are used to make absolute dosimetric measurements of high-energy electron beams. These calibrated beams are then used to calibrate several types of dosimeters for high-dose applications such as medical-product sterilization, polymer modification, food processing, or electronic-device hardness testing. The electron beams are produced either as continuous high-power beams at approximately 4.5 MeV by d.c. type accelerators or in the energy range of approximately 8 to 50 MeV using pulsed microwave linear accelerators (linacs). The continuous beams are generally magnetically scanned to produce a broad, uniform radiation environment for the processing of materials of extended lateral dimensions. The higher-energy pulsed beams may also be scanned for processing applications or may be used in an unscanned, tightly-focused mode to produce maximum absorbed dose rates such as may be required for electronic-device radiation hardness testing. The calorimeters are used over an absorbed dose range of 10 2 to 10 4 Gy. Intercomparison studies are reported between National Institute of Standards and Technology (NIST) and UK National Physical Laboratory (NPL) graphite disk calorimeters at high doses, using the NPL 10-MeV linac, and agreement was found within 1.5%. It was also shown that the electron-beam responses of radiochromic film dosimeters and alanine pellet dosimeters can be accurately calibrated by comparison with calorimeter readings.

Effect of thermal processing during yogurt production upon the detection of staphylococcal enterotoxin B.

PubMed

Principato, Maryann; Boyle, Thomas; Njoroge, Joyce; Jones, Robert L; O'Donnell, Michael

2009-10-01

This research was conducted to examine the inherent properties of yogurt contaminated with staphylococcal enterotoxin B (SEB). Two types of yogurts were produced for this study. Type I yogurts were produced by adding SEB at the start of yogurt production, and type II yogurts were produced by adding SEB after the milk base had been boiled. Biochemical characteristics inherent to yogurt, including pH, lactic acid and acetaldehyde concentrations, were analyzed weekly for each batch beginning at a time just after production and throughout a storage period of at least 4 weeks. The presence of toxin during yogurt production did not result in any significant biochemical or physical changes in yogurt. However, we were unable to detect SEB toxin in type I yogurt using a commercially available enzyme-linked immunosorbent assay (ELISA). In contrast, SEB was easily detectable by our ELISA in type II yogurt samples. Higher levels of SEB were recovered from type II yogurt that had been stored for 1 week than from type II yogurt that had been stored for any other length of time. These results indicate that the biochemical characteristics of yogurt did not change significantly (relative to control yogurt) in the presence of either thermally processed SEB or native SEB. However, the ability to detect SEB by ELISA was dependent on whether the toxin had been processed.

Physico-chemical characterization of natural fermentation process of Conservolea and Kalamàta table olives and developement of a protocol for the pre-selection of fermentation starters.

PubMed

Bleve, Gianluca; Tufariello, Maria; Durante, Miriana; Grieco, Francesco; Ramires, Francesca Anna; Mita, Giovanni; Tasioula-Margari, Maria; Logrieco, Antonio Francesco

2015-04-01

Table olives are one of the most important traditional fermented vegetables in Europe and their world consumption is constantly increasing. Conservolea and Kalamàta are the most important table olives Greek varieties. In the Greek system, the final product is obtained by spontaneous fermentations, without any chemical debittering treatment. This natural fermentation process is not predictable and strongly influenced by the physical-chemical conditions and by the presence of microorganisms contaminating the olives. Natural fermentations of Conservolea and Kalamàta cultivars black olives were studied in order to determine microbiological, biochemical and chemical evolution during the process. Following the process conditions generally used by producers, in both cultivars, yeasts were detected throughout the fermentation, whereas lactic acid bacteria (LAB) appeared in the last staged of the process. A new optimized specific protocol was developed to select autochthonous yeast and LAB isolates that can be good candidates as starters. These microorganisms were pre-selected for their ability to adapt to model brines, to have beta-glucosidase activity, not to produce biogenic amines. Chemical compounds deriving by microbiological activities and associated to the three different phases (30, 90 and 180 days) of the fermentation process were identified and were proposed as chemical descriptors to follow the fermentation progress. Copyright © 2014 Elsevier Ltd. All rights reserved.

A biocompatible tissue scaffold produced by supercritical fluid processing for cartilage tissue engineering.

PubMed

Kim, Su Hee; Jung, Youngmee; Kim, Soo Hyun

2013-03-01

Supercritical fluids are used in various industrial fields, such as the food and medical industries, because they have beneficial physical and chemical properties and are also nonflammable and inexpensive. In particular, supercritical carbon dioxide (ScCO(2)) is attractive due to its mild critical temperature, pressure values, and nontoxicity. Poly(L-lactide-co-ɛ-caprolactone) (PLCL), which is a biocompatible, biodegradable, and very elastic polymer, has been used in cartilage tissue engineering. However, organic solvents, such as chloroform or dichloromethane, are usually used for the fabrication of a PLCL scaffold through conventional methods. This leads to a cytotoxic effect and long processing time for removing solvents. To alleviate these problems, supercritical fluid processing is introduced here. In this study, we fabricated a mechano-active PLCL scaffold by supercritical fluid processing for cartilage tissue engineering, and we compared it with a scaffold made by a conventional solvent-casting method in terms of physical and biological performance. Also, to examine the optimum condition for preparing scaffolds with ScCO(2), we investigated the effects of pressure, temperature, and the depressurization rate on PLCL foaming. The PLCL scaffolds produced by supercritical fluid processing had a homogeneously interconnected porous structure, and they exhibited a narrow pore size distribution. Also, there was no cytotoxicity of the scaffolds made with ScCO(2) compared to the scaffolds made by the solvent-pressing method. The scaffolds were seeded with chondrocytes, and they were subcutaneously implanted into nude mice for up to 4 weeks. In vivo accumulation of extracellular matrix of cell-scaffold constructs demonstrated that the PLCL scaffold made with ScCO(2) formed a mature and well-developed cartilaginous tissue compared to the PLCL scaffold formed by solvent pressing. Consequently, these results indicated that the PLCL scaffolds made by supercritical fluid processing offer well-interconnected and nontoxic substrates for cell growth, avoiding problems associated with a solvent residue. This suggests that these elastic PLCL scaffolds formed by supercritical fluid processing could be used for cartilage tissue engineering.

Physics of Fresh Produce Safety: Role of Diffusion and Tissue Reaction in Sanitization of Leafy Green Vegetables with Liquid and Gaseous Ozone-Based Sanitizers.

PubMed

Shynkaryk, Mykola V; Pyatkovskyy, Taras; Mohamed, Hussein M; Yousef, Ahmed E; Sastry, Sudhir K

2015-12-01

Produce safety has received much recent attention, with the emphasis being largely on discovery of how microbes invade produce. However, the sanitization operation deserves more attention than it has received. The ability of a sanitizer to reach the site of pathogens is a fundamental prerequisite for efficacy. This work addresses the transport processes of ozone (gaseous and liquid) sanitizer for decontamination of leafy greens. The liquid sanitizer was ineffective against Escherichia coli K-12 in situations where air bubbles may be trapped within cavities. A model was developed for diffusion of sanitizer into the interior of produce. The reaction rate of ozone with the surface of a lettuce leaf was determined experimentally and was used in a numerical simulation to evaluate ozone concentrations within the produce and to determine the time required to reach different locations. For aqueous ozone, the penetration depth was limited to several millimeters by ozone self-decomposition due to the significant time required for diffusion. In contrast, gaseous sanitizer was able to reach a depth of 100 mm in several minutes without depletion in the absence of reaction with surfaces. However, when the ozone gas reacted with the produce surface, gas concentration was significantly affected. Simulation data were validated experimentally by measuring ozone concentrations at the bottom of a cylinder made of lettuce leaf. The microbiological test confirmed the relationship between ozone transport, its self-decomposition, reaction with surrounding materials, and the degree of inactivation of E. coli K-12. Our study shows that decontamination of fresh produce, through direct contact with the sanitizer, is more feasible with gaseous than with aqueous sanitizers. Therefore, sanitization during a high-speed washing process is effective only for decontaminating the wash water.

Physical-chemical evaluation of hydraulic fracturing chemicals in the context of produced water treatment.

PubMed

Camarillo, Mary Kay; Domen, Jeremy K; Stringfellow, William T

2016-12-01

Produced water is a significant waste stream that can be treated and reused; however, the removal of production chemicals-such as those added in hydraulic fracturing-must be addressed. One motivation for treating and reusing produced water is that current disposal methods-typically consisting of deep well injection and percolation in infiltration pits-are being limited. Furthermore, oil and gas production often occurs in arid regions where there is demand for new water sources. In this paper, hydraulic fracturing chemical additive data from California are used as a case study where physical-chemical and biodegradation data are summarized and used to screen for appropriate produced water treatment technologies. The data indicate that hydraulic fracturing chemicals are largely treatable; however, data are missing for 24 of the 193 chemical additives identified. More than one-third of organic chemicals have data indicating biodegradability, suggesting biological treatment would be effective. Adsorption-based methods and partitioning of chemicals into oil for subsequent separation is expected to be effective for approximately one-third of chemicals. Volatilization-based treatment methods (e.g. air stripping) will only be effective for approximately 10% of chemicals. Reverse osmosis is a good catch-all with over 70% of organic chemicals expected to be removed efficiently. Other technologies such as electrocoagulation and advanced oxidation are promising but lack demonstration. Chemicals of most concern due to prevalence, toxicity, and lack of data include propargyl alcohol, 2-mercaptoethyl alcohol, tetrakis hydroxymethyl-phosphonium sulfate, thioglycolic acid, 2-bromo-3-nitrilopropionamide, formaldehyde polymers, polymers of acrylic acid, quaternary ammonium compounds, and surfactants (e.g. ethoxylated alcohols). Future studies should examine the fate of hydraulic fracturing chemicals in produced water treatment trains to demonstrate removal and clarify interactions between upstream and downstream processes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Tracking LNOx Downwind to Investigate Driving Production Physics

NASA Astrophysics Data System (ADS)

Lapierre, J. L.; Pusede, S.

2016-12-01

Emissions of nitrogen oxides (NOx) influence atmospheric oxidation chemistry and drive ozone production. In the upper troposphere, lightning production (LNOx) is believed to contribute as much as 70% of the total NOx. Therefore, accurate, process-driven constraints on LNOx are required to understand the global NOx and ozone burden. However, estimates of the amount of NOx produced per lightning flash remain highly uncertain, ranging across multiple orders of magnitude ( 10-1000 moles NOx/flash). Satellite measurements provide unique advantages to study LNOx due to their extensive spatial coverage of the Earth, but despite the mechanism by which lightning produces NOx being generally known, correlations between satellite NO2 and measured flash counts are often observed to be poor. Here, we combine NO2 measurements from the Ozone Monitoring Instrument (OMI), lightning data from the National Lightning Detection Network (NLDN), and wind data from the NCEP North American Regional Reanalysis (NARR) over a 4 year period (2012-2015) to study observed relationships between the occurrence and physical characteristics of lightning (e.g., intracloud/cloud-to-ground ratio, polarity, peak current, and multiplicity) with elevated NO2 columns. We investigate the observed spatial mismatch between high flash rates and elevated upper tropospheric NO2, highlight a number of individual storms as case studies, and describe the winds and chemistry that dislocate LNOx from storms. We then use these new constraints on LNOx to investigate the physical drivers of LNOx production rates.

Immobilization of fungal beta-glucosidase on silica gel and kaolin carriers.

PubMed

Karagulyan, Hakob K; Gasparyan, Vardan K; Decker, Stephen R

2008-03-01

Beta-glucosidase is a key enzyme in the hydrolysis of cellulose for producing feedstock glucose for various industrial processes. Reuse of enzyme through immobilization can significantly improve the economic characteristics of the process. Immobilization of the fungal beta-glucosidase by covalent binding and physical adsorption on silica gel and kaolin was conducted for consequent application of these procedures in large-scale industrial processes. Different immobilization parameters (incubation time, ionic strength, pH, enzyme/support ratio, glutaric aldehyde concentration, etc.) were evaluated for their effect on the thermal stability of the immobilized enzyme. It was shown that the immobilized enzyme activity is stable at 50 degrees C over 8 days. It has also been shown that in the case of immobilization on kaolin, approximately 95% of the initial enzyme was immobilized onto support, and loss of activity was not observed. However, covalent binding of the enzyme to silica gel brings significant loss of enzyme activity, and only 35% of activity was preserved. In the case of physical adsorption on kaolin, gradual desorption of enzyme takes place. To prevent this process, we have carried out chemical modification of the protein. As a result, after repeated washings, enzyme desorption from kaolin has been reduced from 75 to 20-25% loss.

Immobilization of Fungal β-Glucosidase on Silica Gel and Kaolin Carriers

NASA Astrophysics Data System (ADS)

Karagulyan, Hakob K.; Gasparyan, Vardan K.; Decker, Stephen R.

β-Glucosidase is a key enzyme in the hydrolysis of cellulose for producing feedstock glucose for various industrial processes. Reuse of enzyme through immobilization can significantly improve the economic characteristics of the process. Immobilization of the fungal β-glucosidase by covalent binding and physical adsorption on silica gel and kaolin was conducted for consequent application of these procedures in large-scale industrial processes. Different immobilization parameters (incubation time, ionic strength, pH, enzyme/support ratio, glutaric aldehyde concentration, etc.) were evaluated for their effect on the thermal stability of the immobilized enzyme. It was shown that the immobilized enzyme activity is stable at 50 °C over 8 days. It has also been shown that in the case of immobilization on kaolin, approximately 95% of the initial enzyme was immobilized onto support, and loss of activity was not observed. However, covalent binding of the enzyme to silica gel brings significant loss of enzyme activity, and only 35% of activity was preserved. In the case of physical adsorption on kaolin, gradual desorption of enzyme takes place. To prevent this process, we have carried out chemical modification of the protein. As a result, after repeated washings, enzyme desorption from kaolin has been reduced from 75 to 20-25% loss.

Radiation belt electron acceleration during the 17 March 2015 geomagnetic storm: Observations and simulations

DOE PAGES

Li, W.; Ma, Q.; Thorne, R. M.; ...

2016-06-10

Various physical processes are known to cause acceleration, loss, and transport of energetic electrons in the Earth's radiation belts, but their quantitative roles in different time and space need further investigation. During the largest storm over the past decade (17 March 2015), relativistic electrons experienced fairly rapid acceleration up to ~7 MeV within 2 days after an initial substantial dropout, as observed by Van Allen Probes. In the present paper, we evaluate the relative roles of various physical processes during the recovery phase of this large storm using a 3-D diffusion simulation. By quantitatively comparing the observed and simulated electronmore » evolution, we found that chorus plays a critical role in accelerating electrons up to several MeV near the developing peak location and produces characteristic flat-top pitch angle distributions. By only including radial diffusion, the simulation underestimates the observed electron acceleration, while radial diffusion plays an important role in redistributing electrons and potentially accelerates them to even higher energies. Moreover, plasmaspheric hiss is found to provide efficient pitch angle scattering losses for hundreds of keV electrons, while its scattering effect on > 1 MeV electrons is relatively slow. Although an additional loss process is required to fully explain the overestimated electron fluxes at multi-MeV, the combined physical processes of radial diffusion and pitch angle and energy diffusion by chorus and hiss reproduce the observed electron dynamics remarkably well, suggesting that quasi-linear diffusion theory is reasonable to evaluate radiation belt electron dynamics during this big storm.« less

Radiation belt electron acceleration during the 17 March 2015 geomagnetic storm: Observations and simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, W.; Ma, Q.; Thorne, R. M.

Various physical processes are known to cause acceleration, loss, and transport of energetic electrons in the Earth's radiation belts, but their quantitative roles in different time and space need further investigation. During the largest storm over the past decade (17 March 2015), relativistic electrons experienced fairly rapid acceleration up to ~7 MeV within 2 days after an initial substantial dropout, as observed by Van Allen Probes. In the present paper, we evaluate the relative roles of various physical processes during the recovery phase of this large storm using a 3-D diffusion simulation. By quantitatively comparing the observed and simulated electronmore » evolution, we found that chorus plays a critical role in accelerating electrons up to several MeV near the developing peak location and produces characteristic flat-top pitch angle distributions. By only including radial diffusion, the simulation underestimates the observed electron acceleration, while radial diffusion plays an important role in redistributing electrons and potentially accelerates them to even higher energies. Moreover, plasmaspheric hiss is found to provide efficient pitch angle scattering losses for hundreds of keV electrons, while its scattering effect on > 1 MeV electrons is relatively slow. Although an additional loss process is required to fully explain the overestimated electron fluxes at multi-MeV, the combined physical processes of radial diffusion and pitch angle and energy diffusion by chorus and hiss reproduce the observed electron dynamics remarkably well, suggesting that quasi-linear diffusion theory is reasonable to evaluate radiation belt electron dynamics during this big storm.« less

VPython: Writing Real-time 3D Physics Programs

NASA Astrophysics Data System (ADS)

Chabay, Ruth

2001-06-01

VPython (http://cil.andrew.cmu.edu/projects/visual) combines the Python programming language with an innovative 3D graphics module called Visual, developed by David Scherer. Designed to make 3D physics simulations accessible to novice programmers, VPython allows the programmer to write a purely computational program without any graphics code, and produces an interactive realtime 3D graphical display. In a program 3D objects are created and their positions modified by computational algorithms. Running in a separate thread, the Visual module monitors the positions of these objects and renders them many times per second. Using the mouse, one can zoom and rotate to navigate through the scene. After one hour of instruction, students in an introductory physics course at Carnegie Mellon University, including those who have never programmed before, write programs in VPython to model the behavior of physical systems and to visualize fields in 3D. The Numeric array processing module allows the construction of more sophisticated simulations and models as well. VPython is free and open source. The Visual module is based on OpenGL, and runs on Windows, Linux, and Macintosh.

Physical and Chemical Properties of Coal Bottom Ash (CBA) from Tanjung Bin Power Plant

NASA Astrophysics Data System (ADS)

Izzati Raihan Ramzi, Nurul; Shahidan, Shahiron; Zulkhairi Maarof, Mohamad; Ali, Noorwirdawati

2016-11-01

The objective of this study is to determine the physical and chemical characteristics of Coal Bottom Ash (CBA) obtained from Tanjung Bin Power Plant Station and compare them with the characteristics of natural river sand (as a replacement of fine aggregates). Bottom ash is the by-product of coal combustion during the electricity generating process. However, excess bottom ash production due to the high production of electricity in Malaysia has caused several environmental problems. Therefore, several tests have been conducted in order to determine the physical and chemical properties of bottom ash such as specific gravity, density, particle size distribution, Scanning Electron Microscopic (SEM) and X- Ray Fluorescence (XRF) in the attempt to produce sustainable material from waste. The results indicated that the natural fine aggregate and coal bottom ash have very different physical and chemical properties. Bottom ash was classified as Class C ash. The porous structure, angular and rough texture of bottom ash affected its specific gravity and particle density. From the tests, it was found that bottom ash is recommended to be used in concrete as a replacement for fine aggregates.

Intense fusion neutron sources

NASA Astrophysics Data System (ADS)

Kuteev, B. V.; Goncharov, P. R.; Sergeev, V. Yu.; Khripunov, V. I.

2010-04-01

The review describes physical principles underlying efficient production of free neutrons, up-to-date possibilities and prospects of creating fission and fusion neutron sources with intensities of 1015-1021 neutrons/s, and schemes of production and application of neutrons in fusion-fission hybrid systems. The physical processes and parameters of high-temperature plasmas are considered at which optimal conditions for producing the largest number of fusion neutrons in systems with magnetic and inertial plasma confinement are achieved. The proposed plasma methods for neutron production are compared with other methods based on fusion reactions in nonplasma media, fission reactions, spallation, and muon catalysis. At present, intense neutron fluxes are mainly used in nanotechnology, biotechnology, material science, and military and fundamental research. In the near future (10-20 years), it will be possible to apply high-power neutron sources in fusion-fission hybrid systems for producing hydrogen, electric power, and technological heat, as well as for manufacturing synthetic nuclear fuel and closing the nuclear fuel cycle. Neutron sources with intensities approaching 1020 neutrons/s may radically change the structure of power industry and considerably influence the fundamental and applied science and innovation technologies. Along with utilizing the energy produced in fusion reactions, the achievement of such high neutron intensities may stimulate wide application of subcritical fast nuclear reactors controlled by neutron sources. Superpower neutron sources will allow one to solve many problems of neutron diagnostics, monitor nano-and biological objects, and carry out radiation testing and modification of volumetric properties of materials at the industrial level. Such sources will considerably (up to 100 times) improve the accuracy of neutron physics experiments and will provide a better understanding of the structure of matter, including that of the neutron itself.

Patient-reported physical activity questionnaires: A systematic review of content and format

PubMed Central

2012-01-01

Background Many patients with chronic illness are limited in their physical activities. This systematic review evaluates the content and format of patient-reported outcome (PRO) questionnaires that measure physical activity in elderly and chronically ill populations. Methods Questionnaires were identified by a systematic literature search of electronic databases (Medline, Embase, PsychINFO & CINAHL), hand searches (reference sections and PROQOLID database) and expert input. A qualitative analysis was conducted to assess the content and format of the questionnaires and a Venn diagram was produced to illustrate this. Each stage of the review process was conducted by at least two independent reviewers. Results 104 questionnaires fulfilled our criteria. From these, 182 physical activity domains and 1965 items were extracted. Initial qualitative analysis of the domains found 11 categories. Further synthesis of the domains found 4 broad categories: 'physical activity related to general activities and mobility', 'physical activity related to activities of daily living', 'physical activity related to work, social or leisure time activities', and '(disease-specific) symptoms related to physical activity'. The Venn diagram showed that no questionnaires covered all 4 categories and that the '(disease-specific) symptoms related to physical activity' category was often not combined with the other categories. Conclusions A large number of questionnaires with a broad range of physical activity content were identified. Although the content could be broadly organised, there was no consensus on the content and format of physical activity PRO questionnaires in elderly and chronically ill populations. Nevertheless, this systematic review will help investigators to select a physical activity PRO questionnaire that best serves their research question and context. PMID:22414164

A new process for converting SO2 to sulfur without generating secondary pollutants through reactions involving CaS and CaSO4.

PubMed

Sohn, H Y; Kim, Byung-Su

2002-07-01

Nonferrous smelters and coal gasification processes generate environmentally harmful sulfur dioxide streams, most of which are treated to produce sulfuric acid with the accompanying problems of market shortage and transportation difficulties. Some sulfur dioxide streams are scrubbed with an alkali solution or a solid substance such as limestone or dolomite, which in turn generates wastes that pose other pollution problems. While the conversion of sulfur dioxide to elemental sulfur has many environmental advantages, no processes exist that are environmentally acceptable and economically viable. A new method for converting sulfur dioxide to elemental sulfur by a cyclic process involving calcium sulfide and calcium sulfate without generating solid wastes has been developed. In this process, calcium sulfate pellets as the starting raw material are reduced by a suitable reducing agent such as hydrogen to produce calcium sulfide pellets, which are used to reduce sulfur dioxide producing elemental sulfur vapor and calcium sulfate. The latter is then reduced to regenerate calcium sulfide. Thermodynamic analysis and experimental results indicated that the CaS-SO2 reaction produces mainly sulfur vapor and solid calcium sulfate and that the gaseous product from the CaSO4-H2 reaction is mainly water vapor. The rates of the two reactions are reasonably rapid in the temperature range 1000-1100 K, and, importantly, the physical strengths and reactivities of the pellets are maintained largely unchanged up to the tenth cycle, the last cycle tested in this work. Sulfur dioxide-containing streams from certain sources, such as the regenerator off-gas from an integrated gasification combined cycle desulfurization unit and new sulfide smelting plants, contain much higher partial pressures of SO2. In these cases, the rate of the first reaction is expected to be proportionally higher than in the test conditions reported in this paper.

Growth of Bulk Wide Bandgap Semiconductor Crystals and Their Potential Applications

NASA Technical Reports Server (NTRS)

Chen, Kuo-Tong; Shi, Detang; Morgan, S. H.; Collins, W. Eugene; Burger, Arnold

1997-01-01

Developments in bulk crystal growth research for electro-optical devices in the Center for Photonic Materials and Devices since its establishment have been reviewed. Purification processes and single crystal growth systems employing physical vapor transport and Bridgman methods were assembled and used to produce high purity and superior quality wide bandgap materials such as heavy metal halides and II-VI compound semiconductors. Comprehensive material characterization techniques have been employed to reveal the optical, electrical and thermodynamic properties of crystals, and the results were used to establish improved material processing procedures. Postgrowth treatments such as passivation, oxidation, chemical etching and metal contacting during the X-ray and gamma-ray device fabrication process have also been investigated and low noise threshold with improved energy resolution has been achieved.

``Sweetening'' Technical Physics with Hershey's Kisses

NASA Astrophysics Data System (ADS)

Stone, Chuck

2003-04-01

This paper describes an activity in which students measure the mass of each candy in one full bag of Hershey's Kisses and then use a simple spreadsheet program to construct a histogram showing the number of candies as a function of mass. Student measurements indicate that one single bag of 80 Kisses yields enough data to produce a noticeable variation in the candy's mass distribution. The bimodal character of this distribution provides a useful discussion topic. This activity can be performed as a classroom project, a laboratory exercise, or an interactive lecture demonstration. In all these formats, students have the opportunity to collect, organize, process, and analyze real data. In addition to strengthening graphical analysis skills, this activity introduces students to fundamentals of statistics, manufacturing processes in the industrial workplace, and process control techniques.

Processing, structure, property and performance relationships for the thermal spray of the internal surface of aluminum cylinders

NASA Astrophysics Data System (ADS)

Cook, David James

The increased need for automotive weight reduction has necessitated the use of aluminum for engine blocks. Conventional aluminum alloys cannot survive the constant wear from a piston ring reciprocating on the surface. However, a wear resistant thermal spray coating can be applied on the internal surface of the cylinder bore, which has significant advantages over other available options. Thermal spray is a well-established process for depositing molten, semi-molten, or solid particles onto a substrate to form a protective coating. For this application, the two main challenges were obtaining good wear resistance, and achieving good adhesion. To design a system capable of producing a well-adhered, wear resistant coating for this high volume application it is necessary to identify the overall processing, structure, properties, and performance relationships. The results will demonstrate that very important relationships exist among particle characteristics, substrate conditions, and the properties of the final coating. However, it is the scientific studies to understand some of the process physics in these relationships that allow recognition of the critical processing conditions that need to be controlled to ensure a consistent, reliable thermal spray coating. In this investigation, it will be shown that the critical microstructural aspect of the coating that produced the required tribological properties was the presence of wuestite (FeO). It was found that by using a low carbon steel material with compressed air atomizing gas, it was possible to create an Fe/FeO structure that exhibited excellent tribological properties. This study will also show that traditional thermal spray surface preparation techniques were not ideal for this application, therefore a novel alternative approach was developed. The application of a flux to the aluminum surface prior to thermal spray promotes excellent bond strengths to non-roughened aluminum. Analysis will show that this flux strips the oxide from the aluminum and allows for chemical bonding of the NiAl coating to the aluminum via the formation of intermetallics. By developing processing, structure, property, and performance relationships for the full process, it was possible to design a complete coating process to succeed in this application. The determination of these relationships and the underlying process physics improves reliability and instills confidence in the process.

Cell Patterns Emerge from Coupled Chemical and Physical Fields with Cell Proliferation Dynamics: The Arabidopsis thaliana Root as a Study System

PubMed Central

Barrio, Rafael A.; Romero-Arias, José Roberto; Noguez, Marco A.; Azpeitia, Eugenio; Ortiz-Gutiérrez, Elizabeth; Hernández-Hernández, Valeria; Cortes-Poza, Yuriria; Álvarez-Buylla, Elena R.

2013-01-01

A central issue in developmental biology is to uncover the mechanisms by which stem cells maintain their capacity to regenerate, yet at the same time produce daughter cells that differentiate and attain their ultimate fate as a functional part of a tissue or an organ. In this paper we propose that, during development, cells within growing organs obtain positional information from a macroscopic physical field that is produced in space while cells are proliferating. This dynamical interaction triggers and responds to chemical and genetic processes that are specific to each biological system. We chose the root apical meristem of Arabidopsis thaliana to develop our dynamical model because this system is well studied at the molecular, genetic and cellular levels and has the key traits of multicellular stem-cell niches. We built a dynamical model that couples fundamental molecular mechanisms of the cell cycle to a tension physical field and to auxin dynamics, both of which are known to play a role in root development. We perform extensive numerical calculations that allow for quantitative comparison with experimental measurements that consider the cellular patterns at the root tip. Our model recovers, as an emergent pattern, the transition from proliferative to transition and elongation domains, characteristic of stem-cell niches in multicellular organisms. In addition, we successfully predict altered cellular patterns that are expected under various applied auxin treatments or modified physical growth conditions. Our modeling platform may be extended to explicitly consider gene regulatory networks or to treat other developmental systems. PMID:23658505

Physical analyses of compost from composting plants in Brazil.

PubMed

Barreira, L P; Philippi Junior, A; Rodrigues, M S; Tenório, J A S

2008-01-01

Nowadays the composting process has shown itself to be an alternative in the treatment of municipal solid wastes by composting plants. However, although more than 50% of the waste generated by the Brazilian population is composed of matter susceptible to organic composting, this process is, still today, insufficiently developed in Brazil, due to low compost quality and lack of investments in the sector. The objective of this work was to use physical analyses to evaluate the quality of the compost produced at 14 operative composting plants in the Sao Paulo State in Brazil. For this purpose, size distribution and total inert content tests were done. The results were analyzed by grouping the plants according to their productive processes: plants with a rotating drum, plants with shredders or mills, and plants without treatment after the sorting conveyor belt. Compost quality was analyzed considering the limits imposed by the Brazilian Legislation and the European standards for inert contents. The size distribution tests showed the influence of the machinery after the sorting conveyer on the granule sizes as well as the inert content, which contributes to the presence of materials that reduce the quality of the final product.