A New Rock Strength Criterion from Microcracking Mechanisms Which Provides Theoretical Evidence of Hybrid Failure

NASA Astrophysics Data System (ADS)

Zhu, Qi-Zhi

2017-02-01

A proper criterion describing when material fails is essential for deep understanding and constitutive modeling of rock damage and failure by microcracking. Physically, such a criterion should be the global effect of local mechanical response and microstructure evolution inside the material. This paper aims at deriving a new mechanisms-based failure criterion for brittle rocks, based on micromechanical unilateral damage-friction coupling analyses rather than on the basic results from the classical linear elastic fracture mechanics. The failure functions respectively describing three failure modes (purely tensile mode, tensile-shear mode as well as compressive-shear mode) are achieved in a unified upscaling framework and illustrated in the Mohr plane and also in the plane of principal stresses. The strength envelope is proved to be continuous and smooth with a compressive to tensile strength ratio dependent on material properties. Comparisons with experimental data are finally carried out. By this work, we also provide a theoretical evidence on the hybrid failure and the smooth transition from tensile failure to compressive-shear failure.

A vector-based failure detection and isolation algorithm for a dual fail-operational redundant strapdown inertial measurement unit

NASA Technical Reports Server (NTRS)

Morrell, Frederick R.; Bailey, Melvin L.

1987-01-01

A vector-based failure detection and isolation technique for a skewed array of two degree-of-freedom inertial sensors is developed. Failure detection is based on comparison of parity equations with a threshold, and isolation is based on comparison of logic variables which are keyed to pass/fail results of the parity test. A multi-level approach to failure detection is used to ensure adequate coverage for the flight control, display, and navigation avionics functions. Sensor error models are introduced to expose the susceptibility of the parity equations to sensor errors and physical separation effects. The algorithm is evaluated in a simulation of a commercial transport operating in a range of light to severe turbulence environments. A bias-jump failure level of 0.2 deg/hr was detected and isolated properly in the light and moderate turbulence environments, but not detected in the extreme turbulence environment. An accelerometer bias-jump failure level of 1.5 milli-g was detected over all turbulence environments. For both types of inertial sensor, hard-over, and null type failures were detected in all environments without incident. The algorithm functioned without false alarm or isolation over all turbulence environments for the runs tested.

Fear of failure and self-handicapping in college physical education.

PubMed

Chen, Lung Hung; Chen, Mei-Yen; Lin, Meng-Shyan; Kee, Ying Hwa; Shui, Shang-Hsueh

2009-12-01

The purpose of this study was to examine the relationship between fear of failure and self-handicapping within the context of physical education. Participants were 103 college freshmen enrolled in aerobic dance physical education classes in Taiwan. They completed the Performance Failure Appraisal Inventory and Self-Handicapping Scale for Sport 3 mo. after entering the class. Hierarchical regression indicated that scores on fear of failure predicted self-handicapping scores.

Simulation Assisted Risk Assessment Applied to Launch Vehicle Conceptual Design

NASA Technical Reports Server (NTRS)

Mathias, Donovan L.; Go, Susie; Gee, Ken; Lawrence, Scott

2008-01-01

A simulation-based risk assessment approach is presented and is applied to the analysis of abort during the ascent phase of a space exploration mission. The approach utilizes groupings of launch vehicle failures, referred to as failure bins, which are mapped to corresponding failure environments. Physical models are used to characterize the failure environments in terms of the risk due to blast overpressure, resulting debris field, and the thermal radiation due to a fireball. The resulting risk to the crew is dynamically modeled by combining the likelihood of each failure, the severity of the failure environments as a function of initiator and time of the failure, the robustness of the crew module, and the warning time available due to early detection. The approach is shown to support the launch vehicle design process by characterizing the risk drivers and identifying regions where failure detection would significantly reduce the risk to the crew.

Analytical Study of different types Of network failure detection and possible remedies

NASA Astrophysics Data System (ADS)

Saxena, Shikha; Chandra, Somnath

2012-07-01

Faults in a network have various causes,such as the failure of one or more routers, fiber-cuts, failure of physical elements at the optical layer, or extraneous causes like power outages. These faults are usually detected as failures of a set of dependent logical entities and the links affected by the failed components. A reliable control plane plays a crucial role in creating high-level services in the next-generation transport network based on the Generalized Multiprotocol Label Switching (GMPLS) or Automatically Switched Optical Networks (ASON) model. In this paper, approaches to control-plane survivability, based on protection and restoration mechanisms, are examined. Procedures for the control plane state recovery are also discussed, including link and node failure recovery and the concepts of monitoring paths (MPs) and monitoring cycles (MCs) for unique localization of shared risk linked group (SRLG) failures in all-optical networks. An SRLG failure is a failure of multiple links due to a failure of a common resource. MCs (MPs) start and end at same (distinct) monitoring location(s). They are constructed such that any SRLG failure results in the failure of a unique combination of paths and cycles. We derive necessary and sufficient conditions on the set of MCs and MPs needed for localizing an SRLG failure in an arbitrary graph. Procedure of Protection and Restoration of the SRLG failure by backup re-provisioning algorithm have also been discussed.

An evidential reasoning extension to quantitative model-based failure diagnosis

NASA Technical Reports Server (NTRS)

Gertler, Janos J.; Anderson, Kenneth C.

1992-01-01

The detection and diagnosis of failures in physical systems characterized by continuous-time operation are studied. A quantitative diagnostic methodology has been developed that utilizes the mathematical model of the physical system. On the basis of the latter, diagnostic models are derived each of which comprises a set of orthogonal parity equations. To improve the robustness of the algorithm, several models may be used in parallel, providing potentially incomplete and/or conflicting inferences. Dempster's rule of combination is used to integrate evidence from the different models. The basic probability measures are assigned utilizing quantitative information extracted from the mathematical model and from online computation performed therewith.

Fault management for the Space Station Freedom control center

NASA Technical Reports Server (NTRS)

Clark, Colin; Jowers, Steven; Mcnenny, Robert; Culbert, Chris; Kirby, Sarah; Lauritsen, Janet

1992-01-01

This paper describes model based reasoning fault isolation in complex systems using automated digraph analysis. It discusses the use of the digraph representation as the paradigm for modeling physical systems and a method for executing these failure models to provide real-time failure analysis. It also discusses the generality, ease of development and maintenance, complexity management, and susceptibility to verification and validation of digraph failure models. It specifically describes how a NASA-developed digraph evaluation tool and an automated process working with that tool can identify failures in a monitored system when supplied with one or more fault indications. This approach is well suited to commercial applications of real-time failure analysis in complex systems because it is both powerful and cost effective.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Suhas; Wang, Ziwen; Huang, Xiaopeng

While the recent establishment of the role of thermophoresis/diffusion-driven oxygen migration during resistance switching in metal oxide memristors provided critical insights required for memristor modeling, extended investigations of the role of oxygen migration during ageing and failure remain to be detailed. Such detailing will enable failure-tolerant design, which can lead to enhanced performance of memristor-based next-generation storage-class memory. Furthermore, we directly observed lateral oxygen migration using in-situ synchrotron x-ray absorption spectromicroscopy of HfO x memristors during initial resistance switching, wear over millions of switching cycles, and eventual failure, through which we determined potential physical causes of failure. Using this information,more » we reengineered devices to mitigate three failure mechanisms and demonstrated an improvement in endurance of about three orders of magnitude.« less

Cyber-Physical Correlations for Infrastructure Resilience: A Game-Theoretic Approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rao, Nageswara S; He, Fei; Ma, Chris Y. T.

In several critical infrastructures, the cyber and physical parts are correlated so that disruptions to one affect the other and hence the whole system. These correlations may be exploited to strategically launch components attacks, and hence must be accounted for ensuring the infrastructure resilience, specified by its survival probability. We characterize the cyber-physical interactions at two levels: (i) the failure correlation function specifies the conditional survival probability of cyber sub-infrastructure given the physical sub-infrastructure as a function of their marginal probabilities, and (ii) the individual survival probabilities of both sub-infrastructures are characterized by first-order differential conditions. We formulate a resiliencemore » problem for infrastructures composed of discrete components as a game between the provider and attacker, wherein their utility functions consist of an infrastructure survival probability term and a cost term expressed in terms of the number of components attacked and reinforced. We derive Nash Equilibrium conditions and sensitivity functions that highlight the dependence of infrastructure resilience on the cost term, correlation function and sub-infrastructure survival probabilities. These results generalize earlier ones based on linear failure correlation functions and independent component failures. We apply the results to models of cloud computing infrastructures and energy grids.« less

A Comparison of Functional Models for Use in the Function-Failure Design Method

NASA Technical Reports Server (NTRS)

Stock, Michael E.; Stone, Robert B.; Tumer, Irem Y.

2006-01-01

When failure analysis and prevention, guided by historical design knowledge, are coupled with product design at its conception, shorter design cycles are possible. By decreasing the design time of a product in this manner, design costs are reduced and the product will better suit the customer s needs. Prior work indicates that similar failure modes occur with products (or components) with similar functionality. To capitalize on this finding, a knowledge base of historical failure information linked to functionality is assembled for use by designers. One possible use for this knowledge base is within the Elemental Function-Failure Design Method (EFDM). This design methodology and failure analysis tool begins at conceptual design and keeps the designer cognizant of failures that are likely to occur based on the product s functionality. The EFDM offers potential improvement over current failure analysis methods, such as FMEA, FMECA, and Fault Tree Analysis, because it can be implemented hand in hand with other conceptual design steps and carried throughout a product s design cycle. These other failure analysis methods can only truly be effective after a physical design has been completed. The EFDM however is only as good as the knowledge base that it draws from, and therefore it is of utmost importance to develop a knowledge base that will be suitable for use across a wide spectrum of products. One fundamental question that arises in using the EFDM is: At what level of detail should functional descriptions of components be encoded? This paper explores two approaches to populating a knowledge base with actual failure occurrence information from Bell 206 helicopters. Functional models expressed at various levels of detail are investigated to determine the necessary detail for an applicable knowledge base that can be used by designers in both new designs as well as redesigns. High level and more detailed functional descriptions are derived for each failed component based on NTSB accident reports. To best record this data, standardized functional and failure mode vocabularies are used. Two separate function-failure knowledge bases are then created aid compared. Results indicate that encoding failure data using more detailed functional models allows for a more robust knowledge base. Interestingly however, when applying the EFDM, high level descriptions continue to produce useful results when using the knowledge base generated from the detailed functional models.

Minding the Cyber-Physical Gap: Model-Based Analysis and Mitigation of Systemic Perception-Induced Failure.

PubMed

Mordecai, Yaniv; Dori, Dov

2017-07-17

The cyber-physical gap (CPG) is the difference between the 'real' state of the world and the way the system perceives it. This discrepancy often stems from the limitations of sensing and data collection technologies and capabilities, and is inevitable at some degree in any cyber-physical system (CPS). Ignoring or misrepresenting such limitations during system modeling, specification, design, and analysis can potentially result in systemic misconceptions, disrupted functionality and performance, system failure, severe damage, and potential detrimental impacts on the system and its environment. We propose CPG-Aware Modeling & Engineering (CPGAME), a conceptual model-based approach to capturing, explaining, and mitigating the CPG. CPGAME enhances the systems engineer's ability to cope with CPGs, mitigate them by design, and prevent erroneous decisions and actions. We demonstrate CPGAME by applying it for modeling and analysis of the 1979 Three Miles Island 2 nuclear accident, and show how its meltdown could be mitigated. We use ISO-19450:2015-Object Process Methodology as our conceptual modeling framework.

Fundamental Studies of Strength Physics--Methodology of Longevity Prediction of Materials under Arbitrary Thermally and Forced Effects

ERIC Educational Resources Information Center

Petrov, Mark G.

2016-01-01

Thermally activated analysis of experimental data allows considering about the structure features of each material. By modelling the structural heterogeneity of materials by means of rheological models, general and local plastic flows in metals and alloys can be described over. Based on physical fundamentals of failure and deformation of materials…

Origin of anomalous inverse notch effect in bulk metallic glasses

NASA Astrophysics Data System (ADS)

Pan, J.; Zhou, H. F.; Wang, Z. T.; Li, Y.; Gao, H. J.

2015-11-01

Understanding notch-related failure is crucial for the design of reliable engineering structures. However, substantial controversies exist in the literature on the notch effect in bulk metallic glasses (BMGs), and the underlying physical mechanism responsible for the apparent confusion is still poorly understood. Here we investigate the physical origin of an inverse notch effect in a Zr-based metallic glass, where the tensile strength of the material is dramatically enhanced, rather than decreased (as expected from the stress concentration point of view), by introduction of a notch. Our experiments and molecular dynamics simulations show that the seemingly anomalous inverse notch effect is in fact caused by a transition in failure mechanism from shear banding at the notch tip to cavitation and void coalescence. Based on our theoretical analysis, the transition occurs as the stress triaxiality in the notched sample exceeds a material-dependent threshold value. Our results fill the gap in the current understanding of BMG strength and failure mechanism by resolving the conflicts on notch effects and may inspire re-interpretation of previous reports on BMG fracture toughness where pre-existing notches were routinely adopted.

Oxygen migration during resistance switching and failure of hafnium oxide memristors

DOE PAGES

Kumar, Suhas; Wang, Ziwen; Huang, Xiaopeng; ...

2017-03-06

While the recent establishment of the role of thermophoresis/diffusion-driven oxygen migration during resistance switching in metal oxide memristors provided critical insights required for memristor modeling, extended investigations of the role of oxygen migration during ageing and failure remain to be detailed. Such detailing will enable failure-tolerant design, which can lead to enhanced performance of memristor-based next-generation storage-class memory. Furthermore, we directly observed lateral oxygen migration using in-situ synchrotron x-ray absorption spectromicroscopy of HfO x memristors during initial resistance switching, wear over millions of switching cycles, and eventual failure, through which we determined potential physical causes of failure. Using this information,more » we reengineered devices to mitigate three failure mechanisms and demonstrated an improvement in endurance of about three orders of magnitude.« less

Physical Exercise and Patients with Chronic Renal Failure: A Meta-Analysis.

PubMed

Qiu, Zhenzhen; Zheng, Kai; Zhang, Haoxiang; Feng, Ji; Wang, Lizhi; Zhou, Hao

2017-01-01

Chronic renal failure is a severe clinical problem which has some significant socioeconomic impact worldwide and hemodialysis is an important way to maintain patients' health state, but it seems difficult to get better in short time. Considering these, the aim in our research is to update and evaluate the effects of exercise on the health of patients with chronic renal failure. The databases were used to search for the relevant studies in English or Chinese. And the association between physical exercise and health state of patients with chronic renal failure has been investigated. Random-effect model was used to compare the physical function and capacity in exercise and control groups. Exercise is helpful in ameliorating the situation of blood pressure in patients with renal failure and significantly reduces VO 2 in patients with renal failure. The results of subgroup analyses show that, in the age >50, physical activity can significantly reduce blood pressure in patients with renal failure. The activity program containing warm-up, strength, and aerobic exercises has benefits in blood pressure among sick people and improves their maximal oxygen consumption level. These can help patients in physical function and aerobic capacity and may give them further benefits.

Physical Exercise and Patients with Chronic Renal Failure: A Meta-Analysis

PubMed Central

Qiu, Zhenzhen; Zheng, Kai; Zhang, Haoxiang; Feng, Ji; Wang, Lizhi

2017-01-01

Chronic renal failure is a severe clinical problem which has some significant socioeconomic impact worldwide and hemodialysis is an important way to maintain patients' health state, but it seems difficult to get better in short time. Considering these, the aim in our research is to update and evaluate the effects of exercise on the health of patients with chronic renal failure. The databases were used to search for the relevant studies in English or Chinese. And the association between physical exercise and health state of patients with chronic renal failure has been investigated. Random-effect model was used to compare the physical function and capacity in exercise and control groups. Exercise is helpful in ameliorating the situation of blood pressure in patients with renal failure and significantly reduces VO2 in patients with renal failure. The results of subgroup analyses show that, in the age >50, physical activity can significantly reduce blood pressure in patients with renal failure. The activity program containing warm-up, strength, and aerobic exercises has benefits in blood pressure among sick people and improves their maximal oxygen consumption level. These can help patients in physical function and aerobic capacity and may give them further benefits. PMID:28316986

Methods for improved forewarning of condition changes in monitoring physical processes

DOEpatents

Hively, Lee M.

2013-04-09

This invention teaches further improvements in methods for forewarning of critical events via phase-space dissimilarity analysis of data from biomedical equipment, mechanical devices, and other physical processes. One improvement involves objective determination of a forewarning threshold (U.sub.FW), together with a failure-onset threshold (U.sub.FAIL) corresponding to a normalized value of a composite measure (C) of dissimilarity; and providing a visual or audible indication to a human observer of failure forewarning and/or failure onset. Another improvement relates to symbolization of the data according the binary numbers representing the slope between adjacent data points. Another improvement relates to adding measures of dissimilarity based on state-to-state dynamical changes of the system. And still another improvement relates to using a Shannon entropy as the measure of condition change in lieu of a connected or unconnected phase space.

The importance of daily physical activity for improved exercise tolerance in heart failure patients with limited access to centre-based cardiac rehabilitation.

PubMed

Sato, Noriaki; Origuchi, Hideki; Yamamoto, Umpei; Takanaga, Yasuhiro; Mohri, Masahiro

2012-09-01

Supervised cardiac rehabilitation provided at dedicated centres ameliorates exercise intolerance in patients with chronic heart failure. To correlate the amount of physical activity outside the hospital with improved exercise tolerance in patients with limited access to centre-based programs. Forty patients (median age 69 years) with stable heart failure due to systolic left ventricular dysfunction participated in cardiac rehabilitation once per week for five months. Using a validated single-axial accelerometer, the number of steps and physical activity-related energy expenditures on nonrehabilitation days were determined. Median (interquartile range) peak oxygen consumption was increased from 14.4 mL/kg/min (range 12.9 mL/kg/min to 17.8 mL/kg/min) to 16.4 mL/kg/min (range 13.9 mL/kg/min to 19.1 mL/kg/min); P<0.0001, in association with a decreased slope of the minute ventilation to carbon dioxide production plot (34.2 [range 31.3 to 38.1] versus 32.7 [range 30.3 to 36.5]; P<0.0001). Changes in peak oxygen consumption were correlated with the daily number of steps (P<0.01) and physical activity-related energy expenditures (P<0.05). Furthermore, these changes were significantly correlated with total exercise time per day and time spent for light (≤3 metabolic equivalents) exercise, but not with time spent for moderate/vigorous (>3 metabolic equivalents) exercise. The number of steps and energy expenditures outside the hospital were correlated with improved exercise capacity. An accelerometer may be useful for guiding home-based cardiac rehabilitation.

A Methodology for Modeling Nuclear Power Plant Passive Component Aging in Probabilistic Risk Assessment under the Impact of Operating Conditions, Surveillance and Maintenance Activities

NASA Astrophysics Data System (ADS)

Guler Yigitoglu, Askin

In the context of long operation of nuclear power plants (NPPs) (i.e., 60-80 years, and beyond), investigation of the aging of passive systems, structures and components (SSCs) is important to assess safety margins and to decide on reactor life extension as indicated within the U.S. Department of Energy (DOE) Light Water Reactor Sustainability (LWRS) Program. In the traditional probabilistic risk assessment (PRA) methodology, evaluating the potential significance of aging of passive SSCs on plant risk is challenging. Although passive SSC failure rates can be added as initiating event frequencies or basic event failure rates in the traditional event-tree/fault-tree methodology, these failure rates are generally based on generic plant failure data which means that the true state of a specific plant is not reflected in a realistic manner on aging effects. Dynamic PRA methodologies have gained attention recently due to their capability to account for the plant state and thus address the difficulties in the traditional PRA modeling of aging effects of passive components using physics-based models (and also in the modeling of digital instrumentation and control systems). Physics-based models can capture the impact of complex aging processes (e.g., fatigue, stress corrosion cracking, flow-accelerated corrosion, etc.) on SSCs and can be utilized to estimate passive SSC failure rates using realistic NPP data from reactor simulation, as well as considering effects of surveillance and maintenance activities. The objectives of this dissertation are twofold: The development of a methodology for the incorporation of aging modeling of passive SSC into a reactor simulation environment to provide a framework for evaluation of their risk contribution in both the dynamic and traditional PRA; and the demonstration of the methodology through its application to pressurizer surge line pipe weld and steam generator tubes in commercial nuclear power plants. In the proposed methodology, a multi-state physics based model is selected to represent the aging process. The model is modified via sojourn time approach to reflect the operational and maintenance history dependence of the transition rates. Thermal-hydraulic parameters of the model are calculated via the reactor simulation environment and uncertainties associated with both parameters and the models are assessed via a two-loop Monte Carlo approach (Latin hypercube sampling) to propagate input probability distributions through the physical model. The effort documented in this thesis towards this overall objective consists of : i) defining a process for selecting critical passive components and related aging mechanisms, ii) aging model selection, iii) calculating the probability that aging would cause the component to fail, iv) uncertainty/sensitivity analyses, v) procedure development for modifying an existing PRA to accommodate consideration of passive component failures, and, vi) including the calculated failure probability in the modified PRA. The proposed methodology is applied to pressurizer surge line pipe weld aging and steam generator tube degradation in pressurized water reactors.

Statistics-related and reliability-physics-related failure processes in electronics devices and products

NASA Astrophysics Data System (ADS)

Suhir, E.

2014-05-01

The well known and widely used experimental reliability "passport" of a mass manufactured electronic or a photonic product — the bathtub curve — reflects the combined contribution of the statistics-related and reliability-physics (physics-of-failure)-related processes. When time progresses, the first process results in a decreasing failure rate, while the second process associated with the material aging and degradation leads to an increased failure rate. An attempt has been made in this analysis to assess the level of the reliability physics-related aging process from the available bathtub curve (diagram). It is assumed that the products of interest underwent the burn-in testing and therefore the obtained bathtub curve does not contain the infant mortality portion. It has been also assumed that the two random processes in question are statistically independent, and that the failure rate of the physical process can be obtained by deducting the theoretically assessed statistical failure rate from the bathtub curve ordinates. In the carried out numerical example, the Raleigh distribution for the statistical failure rate was used, for the sake of a relatively simple illustration. The developed methodology can be used in reliability physics evaluations, when there is a need to better understand the roles of the statistics-related and reliability-physics-related irreversible random processes in reliability evaluations. The future work should include investigations on how powerful and flexible methods and approaches of the statistical mechanics can be effectively employed, in addition to reliability physics techniques, to model the operational reliability of electronic and photonic products.

Using web-based video to enhance physical examination skills in medical students.

PubMed

Orientale, Eugene; Kosowicz, Lynn; Alerte, Anton; Pfeiffer, Carol; Harrington, Karen; Palley, Jane; Brown, Stacey; Sapieha-Yanchak, Teresa

2008-01-01

Physical examination (PE) skills among U.S. medical students have been shown to be deficient. This study examines the effect of a Web-based physical examination curriculum on first-year medical student PE skills. Web-based video clips, consisting of instruction in 77 elements of the physical examination, were created using Microsoft Windows Moviemaker software. Medical students' PE skills were evaluated by standardized patients before and after implementation of the Internet-based video. Following implementation of this curriculum, there was a higher level of competency (from 87% in 2002-2003 to 91% in 2004-2005), and poor performances on standardized patient PE exams substantially diminished (from a 14%-22%failure rate in 2002-2003, to 4% in 2004-2005. A significant improvement in first-year medical student performance on the adult PE occurred after implementing Web-based instructional video.

Graph-theoretic analysis of discrete-phase-space states for condition change detection and quantification of information

DOEpatents

Hively, Lee M.

2014-09-16

Data collected from devices and human condition may be used to forewarn of critical events such as machine/structural failure or events from brain/heart wave data stroke. By monitoring the data, and determining what values are indicative of a failure forewarning, one can provide adequate notice of the impending failure in order to take preventive measures. This disclosure teaches a computer-based method to convert dynamical numeric data representing physical objects (unstructured data) into discrete-phase-space states, and hence into a graph (structured data) for extraction of condition change.

Functional correlation approach to operational risk in banking organizations

NASA Astrophysics Data System (ADS)

Kühn, Reimer; Neu, Peter

2003-05-01

A Value-at-Risk-based model is proposed to compute the adequate equity capital necessary to cover potential losses due to operational risks, such as human and system process failures, in banking organizations. Exploring the analogy to a lattice gas model from physics, correlations between sequential failures are modeled by as functionally defined, heterogeneous couplings between mutually supportive processes. In contrast to traditional risk models for market and credit risk, where correlations are described as equal-time-correlations by a covariance matrix, the dynamics of the model shows collective phenomena such as bursts and avalanches of process failures.

Learning from Failures: Archiving and Designing with Failure and Risk

NASA Technical Reports Server (NTRS)

VanWie, Michael; Bohm, Matt; Barrientos, Francesca; Turner, Irem; Stone, Robert

2005-01-01

Identifying and mitigating risks during conceptual design remains an ongoing challenge. This work presents the results of collaborative efforts between The University of Missouri-Rolla and NASA Ames Research Center to examine how an early stage mission design team at NASA addresses risk, and, how a computational support tool can assist these designers in their tasks. Results of our observations are given in addition to a brief example of our implementation of a repository based computational tool that allows users to browse and search through archived failure and risk data as related to either physical artifacts or functionality.

Long-term effectiveness of telephone-based health coaching for heart failure patients: A post-only randomised controlled trial.

PubMed

Tiede, Michel; Dwinger, Sarah; Herbarth, Lutz; Härter, Martin; Dirmaier, Jörg

2017-09-01

Introduction The * Equal contributors. health-status of heart failure patients can be improved to some extent by disease self-management. One method of developing such skills is telephone-based health coaching. However, the effects of telephone-based health coaching remain inconclusive. The aim of this study was to evaluate the effects of telephone-based health coaching for people with heart failure. Methods A total sample of 7186 patients with various chronic diseases was randomly assigned to either the coaching or the control group. Then 184 patients with heart failure were selected by International Classification of Diseases (ICD)-10 code for subgroup analysis. Data were collected at 24 and 48 months after the beginning of the coaching. The primary outcome was change in quality of life. Secondary outcomes were changes in depression and anxiety, health-related control beliefs, control preference, health risk behaviour and health-related behaviours. Statistical analyses included a per-protocol evaluation, employing analysis of variance and analysis of covariance (ANCOVA) as well as Mann-Whitney U tests. Results Participants' average age was 73 years (standard deviation (SD) = 9) and the majority were women (52.8%). In ANCOVA analyses there were no significant differences between groups for the change in quality of life (QoL) . However, the coaching group reported a significantly higher level of physical activity ( p = 0.03), lower intake of non-prescribed drugs ( p = 0.04) and lower levels of stress ( p = 0.02) than the control group. Mann-Whitney U tests showed a different external locus of control ( p = 0.014), and higher reduction in unhealthy nutrition ( p = 0.019), physical inactivity ( p = 0.004) and stress ( p = 0.028). Discussion Our results suggest that telephone-based health coaching has no effect on QoL, anxiety and depression of heart failure patients, but helps in improving certain risk behaviours and changes the locus of control to be more externalised.

Representing ductile damage with the dual domain material point method

DOE PAGES

Long, C. C.; Zhang, D. Z.; Bronkhorst, C. A.; ...

2015-12-14

In this study, we incorporate a ductile damage material model into a computational framework based on the Dual Domain Material Point (DDMP) method. As an example, simulations of a flyer plate experiment involving ductile void growth and material failure are performed. The results are compared with experiments performed on high purity tantalum. We also compare the numerical results obtained from the DDMP method with those obtained from the traditional Material Point Method (MPM). Effects of an overstress model, artificial viscosity, and physical viscosity are investigated. Our results show that a physical bulk viscosity and overstress model are important in thismore » impact and failure problem, while physical shear viscosity and artificial shock viscosity have negligible effects. A simple numerical procedure with guaranteed convergence is introduced to solve for the equilibrium plastic state from the ductile damage model.« less

Failure Criteria for FRP Laminates in Plane Stress

NASA Technical Reports Server (NTRS)

Davila, Carlos G.; Camanho, Pedro P.

2003-01-01

A new set of six failure criteria for fiber reinforced polymer laminates is described. Derived from Dvorak's fracture mechanics analyses of cracked plies and from Puck's action plane concept, the physically-based criteria, denoted LaRC03, predict matrix and fiber failure accurately without requiring curve-fitting parameters. For matrix failure under transverse compression, the fracture plane is calculated by maximizing the Mohr-Coulomb effective stresses. A criterion for fiber kinking is obtained by calculating the fiber misalignment under load, and applying the matrix failure criterion in the coordinate frame of the misalignment. Fracture mechanics models of matrix cracks are used to develop a criterion for matrix in tension and to calculate the associated in-situ strengths. The LaRC03 criteria are applied to a few examples to predict failure load envelopes and to predict the failure mode for each region of the envelope. The analysis results are compared to the predictions using other available failure criteria and with experimental results. Predictions obtained with LaRC03 correlate well with the experimental results.

Peer Review of Launch Environments

NASA Technical Reports Server (NTRS)

Wilson, Timmy R.

2011-01-01

Catastrophic failures of launch vehicles during launch and ascent are currently modeled using equivalent trinitrotoluene (TNT) estimates. This approach tends to over-predict the blast effect with subsequent impact to launch vehicle and crew escape requirements. Bangham Engineering, located in Huntsville, Alabama, assembled a less-conservative model based on historical failure and test data coupled with physical models and estimates. This white paper summarizes NESC's peer review of the Bangham analytical work completed to date.

Haul truck tire dynamics due to tire condition

NASA Astrophysics Data System (ADS)

Vaghar Anzabi, R.; Nobes, D. S.; Lipsett, M. G.

2012-05-01

Pneumatic tires are costly components on large off-road haul trucks used in surface mining operations. Tires are prone to damage during operation, and these events can lead to injuries to personnel, loss of equipment, and reduced productivity. Damage rates have significant variability, due to operating conditions and a range of tire fault modes. Currently, monitoring of tire condition is done by physical inspection; and the mean time between inspections is often longer than the mean time between incipient failure and functional failure of the tire. Options for new condition monitoring methods include off-board thermal imaging and camera-based optical methods for detecting abnormal deformation and surface features, as well as on-board sensors to detect tire faults during vehicle operation. Physics-based modeling of tire dynamics can provide a good understanding of the tire behavior, and give insight into observability requirements for improved monitoring systems. This paper describes a model to simulate the dynamics of haul truck tires when a fault is present to determine the effects of physical parameter changes that relate to faults. To simulate the dynamics, a lumped mass 'quarter-vehicle' model has been used to determine the response of the system to a road profile when a failure changes the original properties of the tire. The result is a model of tire vertical displacement that can be used to detect a fault, which will be tested under field conditions in time-varying conditions.

Depressive symptoms and the relationship of inflammation to physical signs and symptoms in heart failure patients.

PubMed

Heo, Seongkum; Moser, Debra K; Pressler, Susan J; Dunbar, Sandra B; Dekker, Rebecca L; Lennie, Terry A

2014-09-01

Depressive symptoms in patients with heart failure can affect the relationship between physical signs and symptoms and inflammation. To examine the relationship between soluble tumor necrosis factor receptor I and physical signs and symptoms and the effects of depressive symptoms on this relationship in patients with heart failure. Data on physical signs and symptoms (Symptom Status Questionnaire-Heart Failure), depressive symptoms (Beck Depression Inventory-II), and levels of the receptor (blood samples) were collected from 145 patients with heart failure. Data on the receptor were square root transformed to achieve normality. Patients were divided into 2 groups according to their scores for depressive symptoms (nondepressed <14 and depressed ≥14). Hierarchical multiple regression was used to analyze the data. In the total sample, with controls for covariates, higher levels of the receptor were significantly related to more severe physical signs and symptoms (F = 7.915; P < .001). In subgroup analyses, with controls for covariates, levels of the receptor were significantly related to physical signs and symptoms only in the patients without depression (F = 3.174; P = .005). Both depressive symptoms and inflammation should be considered along with physical signs and symptoms in patients with heart failure. Further studies are needed to determine the effects of improvement in inflammation on improvement in physical signs and symptoms, with consideration given to the effects of depressive symptoms. ©2014 American Association of Critical-Care Nurses.

An intervention to promote physical activity and self-management in people with stable chronic heart failure The Home-Heart-Walk study: study protocol for a randomized controlled trial

PubMed Central

2011-01-01

Background Chronic heart failure (CHF) is a chronic debilitating condition with economic consequences, mostly because of frequent hospitalisations. Physical activity and adequate self-management capacity are important risk reduction strategies in the management of CHF. The Home-Heart-Walk is a self-monitoring intervention. This model of intervention has adapted the 6-minute walk test as a home-based activity that is self-administered and can be used for monitoring physical functional capacity in people with CHF. The aim of the Home-Heart-Walk program is to promote adherence to physical activity recommendations and improving self-management in people with CHF. Methods/Design A randomised controlled trial is being conducted in English speaking people with CHF in four hospitals in Sydney, Australia. Individuals diagnosed with CHF, in New York Heart Association Functional Class II or III, with a previous admission to hospital for CHF are eligible to participate. Based on a previous CHF study and a loss to follow-up of 10%, 166 participants are required to be able to detect a 12-point difference in the study primary endpoint (SF-36 physical function domain). All enrolled participant receive an information session with a cardiovascular nurse. This information session covers key self-management components of CHF: daily weight; diet (salt reduction); medication adherence; and physical activity. Participants are randomised to either intervention or control group through the study randomisation centre after baseline questionnaires and assessment are completed. For people in the intervention group, the research nurse also explains the weekly Home-Heart-Walk protocol. All participants receive monthly phone calls from a research coordinator for six months, and outcome measures are conducted at one, three and six months. The primary outcome of the trial is the physical functioning domain of quality of life, measured by the physical functioning subscale of the Medical Outcome Study Short Form -36. Secondary outcomes include physical functional capacity measured by the standard six minute walk test, self-management capacity, health related quality of life measured by Medical Outcome Study Short Form -36 and Minnesota Living With Heart Failure Questionnaire, self-efficacy and self-care behaviour. Discussion A self-monitoring intervention that can improve individual's exercise self-efficacy, self-management capacity could have potential significance in improving the management of people with chronic heart failure in community settings. Trial Registration Australian New Zealand Clinical Trial Registry 12609000437268 PMID:21366927

An intervention to promote physical activity and self-management in people with stable chronic heart failure The Home-Heart-Walk study: study protocol for a randomized controlled trial.

PubMed

Du, Hui Y; Newton, Phillip J; Zecchin, Robert; Denniss, Robert; Salamonson, Yenna; Everett, Bronwyn; Currow, David C; Macdonald, Peter S; Davidson, Patricia M

2011-03-02

Chronic heart failure (CHF) is a chronic debilitating condition with economic consequences, mostly because of frequent hospitalisations. Physical activity and adequate self-management capacity are important risk reduction strategies in the management of CHF. The Home-Heart-Walk is a self-monitoring intervention. This model of intervention has adapted the 6-minute walk test as a home-based activity that is self-administered and can be used for monitoring physical functional capacity in people with CHF. The aim of the Home-Heart-Walk program is to promote adherence to physical activity recommendations and improving self-management in people with CHF. A randomised controlled trial is being conducted in English speaking people with CHF in four hospitals in Sydney, Australia. Individuals diagnosed with CHF, in New York Heart Association Functional Class II or III, with a previous admission to hospital for CHF are eligible to participate. Based on a previous CHF study and a loss to follow-up of 10%, 166 participants are required to be able to detect a 12-point difference in the study primary endpoint (SF-36 physical function domain).All enrolled participant receive an information session with a cardiovascular nurse. This information session covers key self-management components of CHF: daily weight; diet (salt reduction); medication adherence; and physical activity. Participants are randomised to either intervention or control group through the study randomisation centre after baseline questionnaires and assessment are completed. For people in the intervention group, the research nurse also explains the weekly Home-Heart-Walk protocol. All participants receive monthly phone calls from a research coordinator for six months, and outcome measures are conducted at one, three and six months. The primary outcome of the trial is the physical functioning domain of quality of life, measured by the physical functioning subscale of the Medical Outcome Study Short Form -36. Secondary outcomes include physical functional capacity measured by the standard six minute walk test, self-management capacity, health related quality of life measured by Medical Outcome Study Short Form -36 and Minnesota Living With Heart Failure Questionnaire, self-efficacy and self-care behaviour. A self-monitoring intervention that can improve individual's exercise self-efficacy, self-management capacity could have potential significance in improving the management of people with chronic heart failure in community settings. Australian New Zealand Clinical Trial Registry 12609000437268.

Incidence of School Failure According to Baseline Leisure-Time Physical Activity Practice: Prospective Study

PubMed Central

Rombaldi, Airton J.; Clark, Valerie L.; Reichert, Felipe F.; Araújo, Cora L.P.; Assunção, Maria C.; Menezes, Ana M.B.; Horta, Bernardo L.; Hallal, Pedro C.

2012-01-01

Purpose To evaluate the prospective association between leisure-time physical activity practice at 11 years of age and incidence of school failure from 11 to 15 years of age. Methods The sample comprised >4,300 adolescents followed up from birth to 15 years of age participating in a birth cohort study in Pelotas, Brazil. The incidence of school failure from age 11 to 15 years was calculated by first excluding from the analyses all subjects who experienced a school failure before 11 years of age, and then categorizing as “positive” all those who reported repeating a grade at school from 11 to 15 years of age. Leisure-time physical activity was measured using a validated questionnaire. Results The incidence of school failure was 47.9% among boys and 38.2% among girls. Adolescents in the top quartile of leisure-time physical activity practice at 11 years of age had a higher likelihood of school failure (OR: 1.36; 95% CI: 1.06, 1.75) compared with the least active adolescents. In adjusted analyses stratified by sex, boys in the top quartile of leisure-time physical activity practice at 11 years of age were also more likely to have failed at school from age 11 to 15 years (OR: 1.60; 95% CI: 1.09, 2.33). Conclusions Adolescents allocating >1,000 min/wk to leisure-time physical activity were more likely to experience a school failure from 11 to 15 years of age. Although this finding does not advocate against physical activity promotion, it indicates that excess time allocated to physical activity may jeopardize school performance among adolescents. PMID:23283155

Incidence of school failure according to baseline leisure-time physical activity practice: prospective study.

PubMed

Rombaldi, Airton J; Clark, Valerie L; Reichert, Felipe F; Araújo, Cora L P; Assunção, Maria C; Menezes, Ana M B; Horta, Bernardo L; Hallal, Pedro C

2012-12-01

To evaluate the prospective association between leisure-time physical activity practice at 11 years of age and incidence of school failure from 11 to 15 years of age. The sample comprised >4,300 adolescents followed up from birth to 15 years of age participating in a birth cohort study in Pelotas, Brazil. The incidence of school failure from age 11 to 15 years was calculated by first excluding from the analyses all subjects who experienced a school failure before 11 years of age, and then categorizing as "positive" all those who reported repeating a grade at school from 11 to 15 years of age. Leisure-time physical activity was measured using a validated questionnaire. The incidence of school failure was 47.9% among boys and 38.2% among girls. Adolescents in the top quartile of leisure-time physical activity practice at 11 years of age had a higher likelihood of school failure (OR: 1.36; 95% CI: 1.06, 1.75) compared with the least active adolescents. In adjusted analyses stratified by sex, boys in the top quartile of leisure-time physical activity practice at 11 years of age were also more likely to have failed at school from age 11 to 15 years (OR: 1.60; 95% CI: 1.09, 2.33). Adolescents allocating >1,000 min/wk to leisure-time physical activity were more likely to experience a school failure from 11 to 15 years of age. Although this finding does not advocate against physical activity promotion, it indicates that excess time allocated to physical activity may jeopardize school performance among adolescents. Copyright © 2012 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

Physical Functioning, Physical Activity, Exercise Self-Efficacy, and Quality of Life Among Individuals With Chronic Heart Failure in Korea: A Cross-Sectional Descriptive Study.

PubMed

Lee, Haejung; Boo, Sunjoo; Yu, Jihyoung; Suh, Soon-Rim; Chun, Kook Jin; Kim, Jong Hyun

2017-04-01

Both the beneficial relationship between exercise and quality of life and the important role played by exercise self-efficacy in maintaining an exercise regimen among individuals with chronic heart failure are well known. However, most nursing interventions for Korean patients with chronic heart failure focus only on providing education related to risk factors and symptoms. Little information is available regarding the influence of physical functions, physical activity, and exercise self-efficacy on quality of life. This study was conducted to examine the impact of physical functioning, physical activity, and exercise self-efficacy on quality of life among individuals with chronic heart failure. This study used a cross-sectional descriptive design. Data were collected from 116 outpatients with chronic heart failure in Korea. Left ventricular ejection fraction and New York Heart Association classifications were chart reviewed. Information pertaining to levels of physical activity, exercise self-efficacy, and quality of life were collected using self-administered questionnaires. Data were analyzed using descriptive statistics, t tests, analyses of variance, correlations, and hierarchical multiple regressions. About 60% of participants were physically inactive, and most showed relatively low exercise self-efficacy. The mean quality-of-life score was 80.09. The significant correlates for quality of life were poverty, functional status, physical inactivity, and exercise self-efficacy. Collectively, these four variables accounted for 50% of the observed total variance in quality of life. Approaches that focus on enhancing exercise self-efficacy may improve patient-centered outcomes in those with chronic heart failure. In light of the low level of exercise self-efficacy reported and the demonstrated ability of this factor to predict quality of life, the development of effective strategies to enhance exercise self-efficacy offers a novel and effective approach to improving the quality of life of patients with chronic heart failure. Nurses should be proactive in advising patients with chronic heart failure to be more physically active and to enhance their self-confidence in diverse ways.

Simulating stick-slip failure in a sheared granular layer using a physics-based constitutive model

DOE PAGES

Lieou, Charles K. C.; Daub, Eric G.; Guyer, Robert A.; ...

2017-01-14

In this paper, we model laboratory earthquakes in a biaxial shear apparatus using the Shear-Transformation-Zone (STZ) theory of dense granular flow. The theory is based on the observation that slip events in a granular layer are attributed to grain rearrangement at soft spots called STZs, which can be characterized according to principles of statistical physics. We model lab data on granular shear using STZ theory and document direct connections between the STZ approach and rate-and-state friction. We discuss the stability transition from stable shear to stick-slip failure and show that stick slip is predicted by STZ when the applied shearmore » load exceeds a threshold value that is modulated by elastic stiffness and frictional rheology. Finally, we also show that STZ theory mimics fault zone dilation during the stick phase, consistent with lab observations.« less

Overview of Threats and Failure Models for Safety-Relevant Computer-Based Systems

NASA Technical Reports Server (NTRS)

Torres-Pomales, Wilfredo

2015-01-01

This document presents a high-level overview of the threats to safety-relevant computer-based systems, including (1) a description of the introduction and activation of physical and logical faults; (2) the propagation of their effects; and (3) function-level and component-level error and failure mode models. These models can be used in the definition of fault hypotheses (i.e., assumptions) for threat-risk mitigation strategies. This document is a contribution to a guide currently under development that is intended to provide a general technical foundation for designers and evaluators of safety-relevant systems.

L70 life prediction for solid state lighting using Kalman Filter and Extended Kalman Filter based models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lall, Pradeep; Wei, Junchao; Davis, Lynn

2013-08-08

Solid-state lighting (SSL) luminaires containing light emitting diodes (LEDs) have the potential of seeing excessive temperatures when being transported across country or being stored in non-climate controlled warehouses. They are also being used in outdoor applications in desert environments that see little or no humidity but will experience extremely high temperatures during the day. This makes it important to increase our understanding of what effects high temperature exposure for a prolonged period of time will have on the usability and survivability of these devices. Traditional light sources “burn out” at end-of-life. For an incandescent bulb, the lamp life is definedmore » by B50 life. However, the LEDs have no filament to “burn”. The LEDs continually degrade and the light output decreases eventually below useful levels causing failure. Presently, the TM-21 test standard is used to predict the L70 life of LEDs from LM-80 test data. Several failure mechanisms may be active in a LED at a single time causing lumen depreciation. The underlying TM-21 Model may not capture the failure physics in presence of multiple failure mechanisms. Correlation of lumen maintenance with underlying physics of degradation at system-level is needed. In this paper, Kalman Filter (KF) and Extended Kalman Filters (EKF) have been used to develop a 70-percent Lumen Maintenance Life Prediction Model for LEDs used in SSL luminaires. Ten-thousand hour LM-80 test data for various LEDs have been used for model development. System state at each future time has been computed based on the state space at preceding time step, system dynamics matrix, control vector, control matrix, measurement matrix, measured vector, process noise and measurement noise. The future state of the lumen depreciation has been estimated based on a second order Kalman Filter model and a Bayesian Framework. The measured state variable has been related to the underlying damage using physics-based models. Life prediction of L70 life for the LEDs used in SSL luminaires from KF and EKF based models have been compared with the TM-21 model predictions and experimental data.« less

Minding the Cyber-Physical Gap: Model-Based Analysis and Mitigation of Systemic Perception-Induced Failure

PubMed Central

2017-01-01

The cyber-physical gap (CPG) is the difference between the ‘real’ state of the world and the way the system perceives it. This discrepancy often stems from the limitations of sensing and data collection technologies and capabilities, and is inevitable at some degree in any cyber-physical system (CPS). Ignoring or misrepresenting such limitations during system modeling, specification, design, and analysis can potentially result in systemic misconceptions, disrupted functionality and performance, system failure, severe damage, and potential detrimental impacts on the system and its environment. We propose CPG-Aware Modeling & Engineering (CPGAME), a conceptual model-based approach to capturing, explaining, and mitigating the CPG. CPGAME enhances the systems engineer’s ability to cope with CPGs, mitigate them by design, and prevent erroneous decisions and actions. We demonstrate CPGAME by applying it for modeling and analysis of the 1979 Three Miles Island 2 nuclear accident, and show how its meltdown could be mitigated. We use ISO-19450:2015—Object Process Methodology as our conceptual modeling framework. PMID:28714910

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Chao; Xu, Jun; Cao, Lei

The electrodes of lithium-ion batteries (LIB) are known to be brittle and to fail earlier than the separators during an external crush event. Thus, the understanding of mechanical failure mechanism for LIB electrodes (anode and cathode) is critical for the safety design of LIB cells. In this paper, we present experimental and numerical studies on the constitutive behavior and progression of failure in LIB electrodes. Mechanical tests were designed and conducted to evaluate the constitutive properties of porous electrodes. Constitutive models were developed to describe the stress-strain response of electrodes under uniaxial tensile and compressive loads. The failure criterion andmore » a damage model were introduced to model their unique tensile and compressive failure behavior. The failure mechanism of LIB electrodes was studied using the blunt rod test on dry electrodes, and numerical models were built to simulate progressive failure. The different failure processes were examined and analyzed in detail numerically, and correlated with experimentally observed failure phenomena. Finally, the test results and models improve our understanding of failure behavior in LIB electrodes, and provide constructive insights on future development of physics-based safety design tools for battery structures under mechanical abuse.« less

Tsallis entropy and complexity theory in the understanding of physics of precursory accelerating seismicity.

NASA Astrophysics Data System (ADS)

Vallianatos, Filippos; Chatzopoulos, George

2014-05-01

Strong observational indications support the hypothesis that many large earthquakes are preceded by accelerating seismic release rates which described by a power law time to failure relation. In the present work, a unified theoretical framework is discussed based on the ideas of non-extensive statistical physics along with fundamental principles of physics such as the energy conservation in a faulted crustal volume undergoing stress loading. We derive the time-to-failure power-law of: a) cumulative number of earthquakes, b) cumulative Benioff strain and c) cumulative energy released in a fault system that obeys a hierarchical distribution law extracted from Tsallis entropy. Considering the analytic conditions near the time of failure, we derive from first principles the time-to-failure power-law and show that a common critical exponent m(q) exists, which is a function of the non-extensive entropic parameter q. We conclude that the cumulative precursory parameters are function of the energy supplied to the system and the size of the precursory volume. In addition the q-exponential distribution which describes the fault system is a crucial factor on the appearance of power-law acceleration in the seismicity. Our results based on Tsallis entropy and the energy conservation gives a new view on the empirical laws derived by other researchers. Examples and applications of this technique to observations of accelerating seismicity will also be presented and discussed. This work was implemented through the project IMPACT-ARC in the framework of action "ARCHIMEDES III-Support of Research Teams at TEI of Crete" (MIS380353) of the Operational Program "Education and Lifelong Learning" and is co-financed by the European Union (European Social Fund) and Greek national funds

Contract-Based Integration of Cyber-Physical Analyses

DTIC Science & Technology

2014-10-14

for cyber-physical systems , 2013 [3] Torngren et al. Integrating viewpoints in the development of mechatronic products, 2013 [4] Rajhans et al...Conference on Embedded Software Report Documentation Page Form ApprovedOMB No. 0704-0188 Public reporting burden for the collection of information is...failures 5 Analytic aspect of integration Sensor Sampling PID Controller Actuator Controller Communication bus Sensor board CPU Actuator board System Bin

A correlational study of illness knowledge, self-care behaviors, and quality of life in elderly patients with heart failure.

PubMed

Liu, Min-Hui; Wang, Chao-Hung; Huang, Yu-Yen; Cherng, Wen-Jin; Wang, Kai-Wei Katherine

2014-06-01

Patients with heart failure experience adverse physical symptoms that affect quality of life. The number of patients with heart failure in Taiwan has been growing in recent years. This article examines correlations among illness knowledge, self-care behaviors, and quality of life in elderly patients with heart failure. A cross-sectional research design using three questionnaires was adopted. The study was undertaken in an outpatient department of a teaching hospital in Taiwan from January to June 2008. Potential participants aged 65 years or older were selected by a physician based on several diagnostic findings of heart failure that included an International Classification of Diseases' code 4280 or 4289. Patients who were bedridden or had a prognosis of less than 6 months were excluded from consideration. One hundred forty-one patients with heart failure were recruited. Most participants were men (51.8%), older adults (49.6% older than 71 years old), and either educated to an elementary school level or illiterate (69.5%) and have New York Heart Association class II (61.0%). Participants had an average left ventricular ejection fraction of 41.1%. The illness knowledge of participants was poor (accuracy rate: 29.3%), and most were unaware of the significance of self-care. Illness knowledge correlated with both self-care behaviors (r = -.42, p < .01) and quality of life (r = -.22, p < .01). Illness knowledge and age were identified as significant correlated factors of self-care behaviors (R = .22); and functional class, living independently, and age were identified as significant correlated factors of quality of life (R = .41). Participants in this study with higher self-reported self-care behaviors and quality of life were younger in age and had better illness knowledge. Furthermore, physical function and independence in daily living significantly affected quality of life. Care for patients with heart failure, particularly older adults, should focus on teaching these patients about heart failure illness and symptom management. Assisting elderly patients with heart failure to promote and maintain physical functions to handle activities of daily living independently is critical to improving patient quality of life.

Physics-based Entry, Descent and Landing Risk Model

NASA Technical Reports Server (NTRS)

Gee, Ken; Huynh, Loc C.; Manning, Ted

2014-01-01

A physics-based risk model was developed to assess the risk associated with thermal protection system failures during the entry, descent and landing phase of a manned spacecraft mission. In the model, entry trajectories were computed using a three-degree-of-freedom trajectory tool, the aerothermodynamic heating environment was computed using an engineering-level computational tool and the thermal response of the TPS material was modeled using a one-dimensional thermal response tool. The model was capable of modeling the effect of micrometeoroid and orbital debris impact damage on the TPS thermal response. A Monte Carlo analysis was used to determine the effects of uncertainties in the vehicle state at Entry Interface, aerothermodynamic heating and material properties on the performance of the TPS design. The failure criterion was set as a temperature limit at the bondline between the TPS and the underlying structure. Both direct computation and response surface approaches were used to compute the risk. The model was applied to a generic manned space capsule design. The effect of material property uncertainty and MMOD damage on risk of failure were analyzed. A comparison of the direct computation and response surface approach was undertaken.

RVR Meander – Migration of meandering rivers in homogeneous and heterogeneous floodplains using physically-based bank erosion

USDA-ARS?s Scientific Manuscript database

The RVR Meander platform for computing long-term meandering-channel migration is presented, together with a method for planform migration based on the modeling of the streambank erosion processes of hydraulic erosion and mass failure. An application to a real-world river, with assumption of homogene...

Effects of Students' Race, Physical Attractiveness, and Dialect on Teachers' Evaluations

ERIC Educational Resources Information Center

DeMeis, Debra Kanai; Turner, Ralph R.

1978-01-01

Based on taped samples of the students' speech, 68 white elementary school teachers rated subjects on personality, quality of response, and current and future academic abilities. Black students, Black English-speaking students and unattractive students were rated consistently lower. Academic failure may result from evaluations based on race and…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Puskar, Joseph David; Quintana, Michael A.; Sorensen, Neil Robert

A program is underway at Sandia National Laboratories to predict long-term reliability of photovoltaic (PV) systems. The vehicle for the reliability predictions is a Reliability Block Diagram (RBD), which models system behavior. Because this model is based mainly on field failure and repair times, it can be used to predict current reliability, but it cannot currently be used to accurately predict lifetime. In order to be truly predictive, physics-informed degradation processes and failure mechanisms need to be included in the model. This paper describes accelerated life testing of metal foil tapes used in thin-film PV modules, and how tape jointmore » degradation, a possible failure mode, can be incorporated into the model.« less

ROENTGEN: case-based reasoning and radiation therapy planning.

PubMed Central

Berger, J.

1992-01-01

ROENTGEN is a design assistant for radiation therapy planning which uses case-based reasoning, an artificial intelligence technique. It learns both from specific problem-solving experiences and from direct instruction from the user. The first sort of learning is the normal case-based method of storing problem solutions so that they can be reused. The second sort is necessary because ROENTGEN does not, initially, have an internal model of the physics of its problem domain. This dependence on explicit user instruction brings to the forefront representational questions regarding indexing, failure definition, failure explanation and repair. This paper presents the techniques used by ROENTGEN in its knowledge acquisition and design activities. PMID:1482869

Documenting the conversion from traditional to Studio Physics formats at the Colorado School of Mines: Process and early results

NASA Astrophysics Data System (ADS)

Kohl, Patrick B.; Kuo, H. Vincent; Ruskell, Todd G.

2008-10-01

The Colorado School of Mines (CSM) has taught its first-semester introductory physics course using a hybrid lecture/Studio Physics format for several years. Over the past year we have converted the second semester of our calculus-based introductory physics course (Physics II) to a Studio Physics format, starting from a traditional lecture-based format. In this paper, we document the early stages of this conversion in order to better understand which features succeed and which do not, and in order to develop a model for switching to Studio that keeps the time and resource investment manageable. We describe the recent history of the Physics II course and of Studio at Mines, discuss the PER-based improvements that we are implementing, and characterize our progress via several metrics, including pre/post Conceptual Survey of Electricity and Magnetism (CSEM) scores, Colorado Learning About Science Survey scores (CLASS), solicited student comments, failure rates, and exam scores.

Studio Physics at the Colorado School of Mines: A model for iterative development and assessment

NASA Astrophysics Data System (ADS)

Kohl, Patrick; Kuo, Vincent

2009-05-01

The Colorado School of Mines (CSM) has taught its first-semester introductory physics course using a hybrid lecture/Studio Physics format for several years. Based on this previous success, over the past 18 months we have converted the second semester of our traditional calculus-based introductory physics course (Physics II) to a Studio Physics format. In this talk, we describe the recent history of the Physics II course and of Studio at Mines, discuss the PER-based improvements that we are implementing, and characterize our progress via several metrics, including pre/post Conceptual Survey of Electricity and Magnetism (CSEM) scores, Colorado Learning About Science Survey scores (CLASS), failure rates, and exam scores. We also report on recent attempts to involve students in the department's Senior Design program with our course. Our ultimate goal is to construct one possible model for a practical and successful transition from a lecture course to a Studio (or Studio-like) course.

Estimation of lifetime distributions on 1550-nm DFB laser diodes using Monte-Carlo statistic computations

NASA Astrophysics Data System (ADS)

Deshayes, Yannick; Verdier, Frederic; Bechou, Laurent; Tregon, Bernard; Danto, Yves; Laffitte, Dominique; Goudard, Jean Luc

2004-09-01

High performance and high reliability are two of the most important goals driving the penetration of optical transmission into telecommunication systems ranging from 880 nm to 1550 nm. Lifetime prediction defined as the time at which a parameter reaches its maximum acceptable shirt still stays the main result in terms of reliability estimation for a technology. For optoelectronic emissive components, selection tests and life testing are specifically used for reliability evaluation according to Telcordia GR-468 CORE requirements. This approach is based on extrapolation of degradation laws, based on physics of failure and electrical or optical parameters, allowing both strong test time reduction and long-term reliability prediction. Unfortunately, in the case of mature technology, there is a growing complexity to calculate average lifetime and failure rates (FITs) using ageing tests in particular due to extremely low failure rates. For present laser diode technologies, time to failure tend to be 106 hours aged under typical conditions (Popt=10 mW and T=80°C). These ageing tests must be performed on more than 100 components aged during 10000 hours mixing different temperatures and drive current conditions conducting to acceleration factors above 300-400. These conditions are high-cost, time consuming and cannot give a complete distribution of times to failure. A new approach consists in use statistic computations to extrapolate lifetime distribution and failure rates in operating conditions from physical parameters of experimental degradation laws. In this paper, Distributed Feedback single mode laser diodes (DFB-LD) used for 1550 nm telecommunication network working at 2.5 Gbit/s transfer rate are studied. Electrical and optical parameters have been measured before and after ageing tests, performed at constant current, according to Telcordia GR-468 requirements. Cumulative failure rates and lifetime distributions are computed using statistic calculations and equations of drift mechanisms versus time fitted from experimental measurements.

Physical nature of longevity of light actinides in dynamic failure phenomenon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Uchaev, A. Ya., E-mail: uchaev@expd.vniief.ru; Punin, V. T.; Selchenkova, N. I.

It is shown in this work that the physical nature of the longevity of light actinides under extreme conditions in a range of nonequilibrium states of t ∼ 10{sup –6}–10{sup –10} s is determined by the time needed for the formation of a critical concentration of a cascade of failure centers, which changes connectivity of the body. These centers form a percolation cluster. The longevity is composed of waiting time t{sub w} for the appearance of failure centers and clusterization time t{sub c} of cascade of failure centers, when connectivity in the system of failure centers and the percolation clustermore » arise. A unique mechanism of the dynamic failure process, a unique order parameter, and an equal dimensionality of the space in which the process occurs determine the physical nature of the longevity of metals, including fissionable materials.« less

Is vision function related to physical functional ability in older adults?

PubMed

West, Catherine G; Gildengorin, Ginny; Haegerstrom-Portnoy, Gunilla; Schneck, Marilyn E; Lott, Lori; Brabyn, John A

2002-01-01

To assess the relationship between a broad range of vision functions and measures of physical performance in older adults. Cross-sectional study. Population-based cohort of community-dwelling older adults, subset of an on-going longitudinal study. Seven hundred eighty-two adults aged 55 and older (65% of living eligible subjects) had subjective health measures and objective physical performance evaluated in 1989/91 and again in 1993/95 and a battery of vision functions tested in 1993/95. Comprehensive battery of vision tests (visual acuity, contrast sensitivity, effects of illumination level, contrast and glare on acuity, visual fields with and without attentional load, color vision, temporal sensitivity, and the impact of dimming light on walking ability) and physical function measures (self-reported mobility limitations and observed measures of walking, rising from a chair and tandem balance). The failure rate for all vision functions and physical performance measures increased exponentially with age. Standard high-contrast visual acuity and standard visual fields showed the lowest failure rates. Nonstandard vision tests showed much higher failure rates. Poor performance on many individual vision functions was significantly associated with particular individual measures of physical performance. Using constructed combination vision variables, significant associations were found between spatial vision, field integrity, binocularity and/or adaptation, and each of the functional outcomes. Vision functions other than standard visual acuity may affect day-to-day functioning of older adults. Additional studies of these other aspects of vision and how they can be treated or rehabilitated are needed to determine whether these aspects play a role in strategies for reducing disability in older adults.

Reliability Evaluation of Next Generation Inverter: Cooperative Research and Development Final Report, CRADA Number CRD-12-478

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paret, Paul

The National Renewable Energy Laboratory (NREL) will conduct thermal and reliability modeling on three sets of power modules for the development of a next generation inverter for electric traction drive vehicles. These modules will be chosen by General Motors (GM) to represent three distinct technological approaches to inverter power module packaging. Likely failure mechanisms will be identified in each package and a physics-of-failure-based reliability assessment will be conducted.

Spectromicroscopic insights for rational design of redox-based memristive devices

PubMed Central

Baeumer, Christoph; Schmitz, Christoph; Ramadan, Amr H. H.; Du, Hongchu; Skaja, Katharina; Feyer, Vitaliy; Müller, Philipp; Arndt, Benedikt; Jia, Chun-Lin; Mayer, Joachim; De Souza, Roger A.; Michael Schneider, Claus; Waser, Rainer; Dittmann, Regina

2015-01-01

The demand for highly scalable, low-power devices for data storage and logic operations is strongly stimulating research into resistive switching as a novel concept for future non-volatile memory devices. To meet technological requirements, it is imperative to have a set of material design rules based on fundamental material physics, but deriving such rules is proving challenging. Here, we elucidate both switching mechanism and failure mechanism in the valence-change model material SrTiO3, and on this basis we derive a design rule for failure-resistant devices. Spectromicroscopy reveals that the resistance change during device operation and failure is indeed caused by nanoscale oxygen migration resulting in localized valence changes between Ti4+ and Ti3+. While fast reoxidation typically results in retention failure in SrTiO3, local phase separation within the switching filament stabilizes the retention. Mimicking this phase separation by intentionally introducing retention-stabilization layers with slow oxygen transport improves retention times considerably. PMID:26477940

Constitutive behavior and progressive mechanical failure of electrodes in lithium-ion batteries

NASA Astrophysics Data System (ADS)

Zhang, Chao; Xu, Jun; Cao, Lei; Wu, Zenan; Santhanagopalan, Shriram

2017-07-01

The electrodes of lithium-ion batteries (LIB) are known to be brittle and to fail earlier than the separators during an external crush event. Thus, the understanding of mechanical failure mechanism for LIB electrodes (anode and cathode) is critical for the safety design of LIB cells. In this paper, we present experimental and numerical studies on the constitutive behavior and progression of failure in LIB electrodes. Mechanical tests were designed and conducted to evaluate the constitutive properties of porous electrodes. Constitutive models were developed to describe the stress-strain response of electrodes under uniaxial tensile and compressive loads. The failure criterion and a damage model were introduced to model their unique tensile and compressive failure behavior. The failure mechanism of LIB electrodes was studied using the blunt rod test on dry electrodes, and numerical models were built to simulate progressive failure. The different failure processes were examined and analyzed in detail numerically, and correlated with experimentally observed failure phenomena. The test results and models improve our understanding of failure behavior in LIB electrodes, and provide constructive insights on future development of physics-based safety design tools for battery structures under mechanical abuse.

Constitutive behavior and progressive mechanical failure of electrodes in lithium-ion batteries

DOE PAGES

Zhang, Chao; Xu, Jun; Cao, Lei; ...

2017-05-05

The electrodes of lithium-ion batteries (LIB) are known to be brittle and to fail earlier than the separators during an external crush event. Thus, the understanding of mechanical failure mechanism for LIB electrodes (anode and cathode) is critical for the safety design of LIB cells. In this paper, we present experimental and numerical studies on the constitutive behavior and progression of failure in LIB electrodes. Mechanical tests were designed and conducted to evaluate the constitutive properties of porous electrodes. Constitutive models were developed to describe the stress-strain response of electrodes under uniaxial tensile and compressive loads. The failure criterion andmore » a damage model were introduced to model their unique tensile and compressive failure behavior. The failure mechanism of LIB electrodes was studied using the blunt rod test on dry electrodes, and numerical models were built to simulate progressive failure. The different failure processes were examined and analyzed in detail numerically, and correlated with experimentally observed failure phenomena. Finally, the test results and models improve our understanding of failure behavior in LIB electrodes, and provide constructive insights on future development of physics-based safety design tools for battery structures under mechanical abuse.« less

Perceived success/failure and attributions associated with self-regulatory efficacy to meet physical activity recommendations for women with arthritis.

PubMed

Spink, Kevin S; Brawley, Lawrence R; Gyurcsik, Nancy C

2016-10-01

The relationship between attributional dimensions women assign to the cause of their perceived success or failure at meeting the recommended physical activity dose and self-regulatory efficacy for future physical activity was examined among women with arthritis. Women (N = 117) aged 18-84 years, with self-reported medically-diagnosed arthritis, completed on-line questions in the fall of 2013 assessing endurance physical activity, perceived outcome for meeting the recommended levels of endurance activity, attributions for one's success or failure in meeting the recommendations, and self-regulatory efficacy to schedule/plan endurance activity over the next month. The main theoretically-driven finding revealed that the interaction of the stability dimension with perceived success/failure was significantly related to self-regulatory efficacy for scheduling and planning future physical activity (β = 0.35, p = .002). Outcomes attributed to more versus less stable factors accentuated differences in self-regulatory efficacy beliefs following perceived success and failure at being active. It appears that attributional dimensions were associated with self-regulatory efficacy in women with arthritis. This suggests that rather than objectively observed past mastery experience, women's subjective perceptions and explanations of their past experiences were related to efficacy beliefs, especially following a failure experience.

A Thermal Runaway Failure Model for Low-Voltage BME Ceramic Capacitors with Defects

NASA Technical Reports Server (NTRS)

Teverovsky, Alexander

2017-01-01

Reliability of base metal electrode (BME) multilayer ceramic capacitors (MLCCs) that until recently were used mostly in commercial applications, have been improved substantially by using new materials and processes. Currently, the inception of intrinsic wear-out failures in high quality capacitors became much greater than the mission duration in most high-reliability applications. However, in capacitors with defects degradation processes might accelerate substantially and cause infant mortality failures. In this work, a physical model that relates the presence of defects to reduction of breakdown voltages and decreasing times to failure has been suggested. The effect of the defect size has been analyzed using a thermal runaway model of failures. Adequacy of highly accelerated life testing (HALT) to predict reliability at normal operating conditions and limitations of voltage acceleration are considered. The applicability of the model to BME capacitors with cracks is discussed and validated experimentally.

Frailty Assessment in Heart Failure: an Overview of the Multi-domain Approach.

PubMed

McDonagh, Julee; Ferguson, Caleb; Newton, Phillip J

2018-02-01

The study aims (1) to provide a contemporary description of frailty assessment in heart failure and (2) to provide an overview of multi-domain frailty assessment in heart failure. Frailty assessment is an important predictive measure for mortality and hospitalisation in individuals with heart failure. To date, there are no frailty assessment instruments validated for use in heart failure. This has resulted in significant heterogeneity between studies regarding the assessment of frailty. The most common frailty assessment instrument used in heart failure is the Frailty Phenotype which focuses on five physical domains of frailty; the appropriateness a purely physical measure of frailty in individuals with heart failure who frequently experience decreased exercise tolerance and shortness of breath is yet to be determined. A limited number of studies have approached frailty assessment using a multi-domain view which may be more clinically relevant in heart failure. There remains a lack of consensus regarding frailty assessment and an absence of a validated instrument in heart failure. Despite this, frailty continues to be assessed frequently, primarily for research purposes, using predominantly physical frailty measures. A more multidimensional view of frailty assessment using a multi-domain approach will likely be more sensitive to identifying at risk patients.

Prediction of L70 lumen maintenance and chromaticity for LEDs using extended Kalman filter models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lall, Pradeep; Wei, Junchao; Davis, Lynn

2013-09-30

Solid-state lighting (SSL) luminaires containing light emitting diodes (LEDs) have the potential of seeing excessive temperatures when being transported across country or being stored in non-climate controlled warehouses. They are also being used in outdoor applications in desert environments that see little or no humidity but will experience extremely high temperatures during the day. This makes it important to increase our understanding of what effects high temperature exposure for a prolonged period of time will have on the usability and survivability of these devices. Traditional light sources “burn out” at end-of-life. For an incandescent bulb, the lamp life is definedmore » by B50 life. However, the LEDs have no filament to “burn”. The LEDs continually degrade and the light output decreases eventually below useful levels causing failure. Presently, the TM-21 test standard is used to predict the L70 life of LEDs from LM-80 test data. Several failure mechanisms may be active in a LED at a single time causing lumen depreciation. The underlying TM-21 Model may not capture the failure physics in presence of multiple failure mechanisms. Correlation of lumen maintenance with underlying physics of degradation at system-level is needed. In this paper, Kalman Filter (KF) and Extended Kalman Filters (EKF) have been used to develop a 70-percent Lumen Maintenance Life Prediction Model for LEDs used in SSL luminaires. Ten-thousand hour LM-80 test data for various LEDs have been used for model development. System state at each future time has been computed based on the state space at preceding time step, system dynamics matrix, control vector, control matrix, measurement matrix, measured vector, process noise and measurement noise. The future state of the lumen depreciation has been estimated based on a second order Kalman Filter model and a Bayesian Framework. The measured state variable has been related to the underlying damage using physics-based models. Life prediction of L70 life for the LEDs used in SSL luminaires from KF and EKF based models have been compared with the TM-21 model predictions and experimental data.« less

Optimal Performance Monitoring of Hybrid Mid-Infrared Wavelength MIMO Free Space Optical and RF Wireless Networks in Fading Channels

NASA Astrophysics Data System (ADS)

Schmidt, Barnet Michael

An optimal performance monitoring metric for a hybrid free space optical and radio-frequency (RF) wireless network, the Outage Capacity Objective Function, is analytically developed and studied. Current and traditional methods of performance monitoring of both optical and RF wireless networks are centered on measurement of physical layer parameters, the most common being signal-to-noise ratio, error rate, Q factor, and eye diagrams, occasionally combined with link-layer measurements such as data throughput, retransmission rate, and/or lost packet rate. Network management systems frequently attempt to predict or forestall network failures by observing degradations of these parameters and to attempt mitigation (such as offloading traffic, increasing transmitter power, reducing the data rate, or combinations thereof) prior to the failure. These methods are limited by the frequent low sensitivity of the physical layer parameters to the atmospheric optical conditions (measured by optical signal-to-noise ratio) and the radio frequency fading channel conditions (measured by signal-to-interference ratio). As a result of low sensitivity, measurements of this type frequently are unable to predict impending failures sufficiently in advance for the network management system to take corrective action prior to the failure. We derive and apply an optimal measure of hybrid network performance based on the outage capacity of the hybrid optical and RF channel, the outage capacity objective function. The objective function provides high sensitivity and reliable failure prediction, and considers both the effects of atmospheric optical impairments on the performance of the free space optical segment as well as the effect of RF channel impairments on the radio frequency segment. The radio frequency segment analysis considers the three most common RF channel fading statistics: Rayleigh, Ricean, and Nakagami-m. The novel application of information theory to the underlying physics of the gamma-gamma optical channel and radio fading channels in determining the joint hybrid channel outage capacity provides the best performance estimate under any given set of operating conditions. It is shown that, unlike traditional physical layer performance monitoring techniques, the objective function based upon the outage capacity of the hybrid channel at any combination of OSNR and SIR, is able to predict channel degradation and failure well in advance of the actual outage. An outage in the information-theoretic definition occurs when the offered load exceeds the outage capacity under the current conditions of OSNR and SIR. The optical channel is operated at the "long" mid-infrared wavelength of 10000 nm. which provides improved resistance to scattering compared to shorter wavelengths such as 1550 nm.

Role of the Microcomputer-Based Laboratory Display in Supporting the Construction of New Understandings in Thermal Physics

ERIC Educational Resources Information Center

Russell, David W.; Lucas, Keith B.; McRobbie, Campbell J.

2004-01-01

Teachers' failure to use the microcomputer-based laboratory (MBL) more widely may be a result of not recognizing its capacity to transform laboratory activities. This research aimed to increase understanding of how MBL activities designed to be consistent with a constructivist theory of learning support or constrain student construction of…

Fibre Break Failure Processes in Unidirectional Composites. Part 2: Failure and Critical Damage State Induced by Sustained Tensile Loading

NASA Astrophysics Data System (ADS)

Thionnet, A.; Chou, H. Y.; Bunsell, A.

2015-04-01

The purpose of these three papers is not to just revisit the modelling of unidirectional composites. It is to provide a robust framework based on physical processes that can be used to optimise the design and long term reliability of internally pressurised filament wound structures. The model presented in Part 1 for the case of monotonically loaded unidirectional composites is further developed to consider the effects of the viscoelastic nature of the matrix in determining the kinetics of fibre breaks under slow or sustained loading. It is shown that the relaxation of the matrix around fibre breaks leads to locally increasing loads on neighbouring fibres and in some cases their delayed failure. Although ultimate failure is similar to the elastic case in that clusters of fibre breaks ultimately control composite failure the kinetics of their development varies significantly from the elastic case. Failure loads have been shown to reduce when loading rates are lowered.

Carbon Fiber Strand Tensile Failure Dynamic Event Characterization

NASA Technical Reports Server (NTRS)

Johnson, Kenneth L.; Reeder, James

2016-01-01

There are few if any clear, visual, and detailed images of carbon fiber strand failures under tension useful for determining mechanisms, sequences of events, different types of failure modes, etc. available to researchers. This makes discussion of physics of failure difficult. It was also desired to find out whether the test article-to-test rig interface (grip) played a part in some failures. These failures have nothing to do with stress rupture failure, thus representing a source of waste for the larger 13-00912 investigation into that specific failure type. Being able to identify or mitigate any competing failure modes would improve the value of the 13-00912 test data. The beginnings of the solution to these problems lay in obtaining images of strand failures useful for understanding physics of failure and the events leading up to failure. Necessary steps include identifying imaging techniques that result in useful data, using those techniques to home in on where in a strand and when in the sequence of events one should obtain imaging data.

Self-efficacy: a useful construct to promote physical activity in people with stable chronic heart failure.

PubMed

Du, HuiYun; Everett, Bronwyn; Newton, Phillip J; Salamonson, Yenna; Davidson, Patricia M

2012-02-01

To explore the conceptual underpinnings of self-efficacy to address the barriers to participating in physical activity and propose a model of intervention. The benefits of physical activity in reducing cardiovascular risk have led to evidence-based recommendations for patients with heart disease, including those with chronic heart failure. However, adherence to best practice recommendations is often suboptimal, particularly in those individuals who experience high symptom burden and feel less confident to undertake physical activity. Self-efficacy is the degree of confidence an individual has in his/her ability to perform behaviour under several specific circumstances. Four factors influence an individual's level of self-efficacy: (1) past performance, (2) vicarious experience, (3) verbal persuasion and (4) physiological arousal. Discursive. Using the method of a discursive paper, this article seeks to explore the conceptual underpinnings of self-efficacy to address the barriers to participating in physical activity and proposes a model of intervention, the Home-Heart-Walk, to promote physical activity and monitor functional status. Implementing effective interventions to promote physical activities require appreciation of factors impacting on behaviour change. Addressing concepts relating to self-efficacy in physical activity interventions may promote participation and adherence in the longer term. The increasing burden of chronic disease and the emphasis on self-management strategies underscore the importance of promoting adherence to recommendations, such as physical activity. © 2011 Blackwell Publishing Ltd.

Presumptive Iatrogenic Microcystin-Associated Liver Failure and Encephalopathy in a Holsteiner Gelding.

PubMed

Mittelman, N S; Engiles, J B; Murphy, L; Vudathala, D; Johnson, A L

2016-09-01

An 8-year-old Holsteiner gelding was presented for evaluation of anorexia, obtundation, icterus, and mild colic signs of 48 hours duration. History, physical examination, and initial diagnostics were suggestive of hepatic disease and encephalopathy. Microcystin toxicosis was suspected based on historical administration of a cyanobacteria supplement, associated serum biochemistry abnormalities, and characteristic histopathological changes. Microcystin contamination was confirmed in both supplement containers fed to the horse. Fulminant hepatic failure and encephalopathy progressed resulting in euthanasia. Necropsy findings were consistent with microcystin induced liver failure. Copyright © 2016 The Authors. Journal of Veterinary Internal Medicine published by Wiley Periodicals, Inc. on behalf of the American College of Veterinary Internal Medicine.

Degradation mechanisms in high-power multi-mode InGaAs-AlGaAs strained quantum well lasers for high-reliability applications

NASA Astrophysics Data System (ADS)

Sin, Yongkun; Presser, Nathan; Brodie, Miles; Lingley, Zachary; Foran, Brendan; Moss, Steven C.

2015-03-01

Laser diode manufacturers perform accelerated multi-cell lifetests to estimate lifetimes of lasers using an empirical model. Since state-of-the-art laser diodes typically require a long period of latency before they degrade, significant amount of stress is applied to the lasers to generate failures in relatively short test durations. A drawback of this approach is the lack of mean-time-to-failure data under intermediate and low stress conditions, leading to uncertainty in model parameters (especially optical power and current exponent) and potential overestimation of lifetimes at usage conditions. This approach is a concern especially for satellite communication systems where high reliability is required of lasers for long-term duration in the space environment. A number of groups have studied reliability and degradation processes in GaAs-based lasers, but none of these studies have yielded a reliability model based on the physics of failure. The lack of such a model is also a concern for space applications where complete understanding of degradation mechanisms is necessary. Our present study addresses the aforementioned issues by performing long-term lifetests under low stress conditions followed by failure mode analysis (FMA) and physics of failure investigation. We performed low-stress lifetests on both MBE- and MOCVD-grown broad-area InGaAs- AlGaAs strained QW lasers under ACC (automatic current control) mode to study low-stress degradation mechanisms. Our lifetests have accumulated over 36,000 test hours and FMA is performed on failures using our angle polishing technique followed by EL. This technique allows us to identify failure types by observing dark line defects through a window introduced in backside metal contacts. We also investigated degradation mechanisms in MOCVD-grown broad-area InGaAs-AlGaAs strained QW lasers using various FMA techniques. Since it is a challenge to control defect densities during the growth of laser structures, we chose to control defect densities by introducing extrinsic point defects to the laser via proton irradiation with different energies and fluences. These lasers were subsequently lifetested to study degradation processes in the lasers with different defect densities and also to study precursor signatures of failures - traps and non-radiative recombination centers (NRCs) in pre- and post-stressed lasers. Lastly, we employed focused ion beam (FIB), electron beam induced current (EBIC), and highresolution TEM (HR-TEM) techniques to further study dark line defects and dislocations in both post-aged and postproton irradiated lasers. We report on our long-term low-stress lifetest results and physics of failure investigation results.

SU-E-T-421: Failure Mode and Effects Analysis (FMEA) of Xoft Electronic Brachytherapy for the Treatment of Superficial Skin Cancers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoisak, J; Manger, R; Dragojevic, I

Purpose: To perform a failure mode and effects analysis (FMEA) of the process for treating superficial skin cancers with the Xoft Axxent electronic brachytherapy (eBx) system, given the recent introduction of expanded quality control (QC) initiatives at our institution. Methods: A process map was developed listing all steps in superficial treatments with Xoft eBx, from the initial patient consult to the completion of the treatment course. The process map guided the FMEA to identify the failure modes for each step in the treatment workflow and assign Risk Priority Numbers (RPN), calculated as the product of the failure mode’s probability ofmore » occurrence (O), severity (S) and lack of detectability (D). FMEA was done with and without the inclusion of recent QC initiatives such as increased staffing, physics oversight, standardized source calibration, treatment planning and documentation. The failure modes with the highest RPNs were identified and contrasted before and after introduction of the QC initiatives. Results: Based on the FMEA, the failure modes with the highest RPN were related to source calibration, treatment planning, and patient setup/treatment delivery (Fig. 1). The introduction of additional physics oversight, standardized planning and safety initiatives such as checklists and time-outs reduced the RPNs of these failure modes. High-risk failure modes that could be mitigated with improved hardware and software interlocks were identified. Conclusion: The FMEA analysis identified the steps in the treatment process presenting the highest risk. The introduction of enhanced QC initiatives mitigated the risk of some of these failure modes by decreasing their probability of occurrence and increasing their detectability. This analysis demonstrates the importance of well-designed QC policies, procedures and oversight in a Xoft eBx programme for treatment of superficial skin cancers. Unresolved high risk failure modes highlight the need for non-procedural quality initiatives such as improved planning software and more robust hardware interlock systems.« less

Nonlinear structural crack growth monitoring

DOEpatents

Welch, Donald E.; Hively, Lee M.; Holdaway, Ray F.

2002-01-01

A method and apparatus are provided for the detection, through nonlinear manipulation of data, of an indicator of imminent failure due to crack growth in structural elements. The method is a process of determining energy consumption due to crack growth and correlating the energy consumption with physical phenomena indicative of a failure event. The apparatus includes sensors for sensing physical data factors, processors or the like for computing a relationship between the physical data factors and phenomena indicative of the failure event, and apparatus for providing notification of the characteristics and extent of such phenomena.

Needs of caregivers in heart failure management: A qualitative study

PubMed Central

Frost, Julia; Britten, Nicky; Jolly, Kate; Greaves, Colin; Abraham, Charles; Dalal, Hayes

2015-01-01

Objectives To identify the needs of caregivers supporting a person with heart failure and to inform the development of a caregiver resource to be used as part of a home-based self-management programme. Methods A qualitative study informed by thematic analysis involving 26 caregivers in individual interviews or a focus group. Results Three distinct aspects of caregiver support in heart failure management were identified. Firstly, caregivers identified needs about supporting management of heart failure including: coping with the variability of heart failure symptoms, what to do in an emergency, understanding and managing medicines, providing emotional support, promoting exercise and physical activity, providing personal care, living with a cardiac device and supporting depression management. Secondly, as they make the transition to becoming a caregiver, they need to develop skills to undertake difficult discussions about the role; communicate with health professionals; manage their own mental health, well-being and sleep; and manage home and work. Thirdly, caregivers require skills to engage social support, and voluntary and formal services while recognising that the long-term future is uncertain. Discussion The identification of the needs of caregiver has been used to inform the development of a home-based heart failure intervention facilitated by a trained health care practitioner. PMID:25795144

Riding the Right Wavelet: Quantifying Scale Transitions in Fractured Rocks

NASA Astrophysics Data System (ADS)

Rizzo, Roberto E.; Healy, David; Farrell, Natalie J.; Heap, Michael J.

2017-12-01

The mechanics of brittle failure is a well-described multiscale process that involves a rapid transition from distributed microcracks to localization along a single macroscopic rupture plane. However, considerable uncertainty exists regarding both the length scale at which this transition occurs and the underlying causes that prompt this shift from a distributed to a localized assemblage of cracks or fractures. For the first time, we used an image analysis tool developed to investigate orientation changes at different scales in images of fracture patterns in faulted materials, based on a two-dimensional continuous wavelet analysis. We detected the abrupt change in the fracture pattern from distributed tensile microcracks to localized shear failure in a fracture network produced by triaxial deformation of a sandstone core plug. The presented method will contribute to our ability of unraveling the physical processes at the base of catastrophic rock failure, including the nucleation of earthquakes, landslides, and volcanic eruptions.

SU-E-T-179: Clinical Impact of IMRT Failure Modes at Or Near TG-142 Tolerance Criteria Levels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faught, J Tonigan; Balter, P; Johnson, J

2015-06-15

Purpose: Quantitatively assess the clinical impact of 11 critical IMRT dose delivery failure modes. Methods: Eleven step-and-shoot IMRT failure modes (FMs) were introduced into twelve Pinnacle v9.8 treatment plans. One standard and one highly modulated plan on the IROC IMRT phantom and ten previous H&N patient treatment plans were used. FMs included physics components covered by basic QA near tolerance criteria levels (TG-142) such as beam energy, MLC positioning, and MLC modeling. Resultant DVHs were compared to those of failure-free plans and the severity of plan degradation was assessed considering PTV coverage and OAR and normal tissue tolerances and usedmore » for FMEA severity scoring. Six of these FMs were physically simulated and phantom irradiations performed. TLD and radiochromic film results are used for comparison to treatment planning studies. Results: Based on treatment planning studies, the largest clinical impact from the phantom cases was induced by 2 mm systematic MLC shift in one bank with the combination of a D95% target under dose near 16% and OAR overdose near 8%. Cord overdoses of 5%–11% occurred with gantry angle, collimator angle, couch angle, MLC leaf end modeling, and MLC transmission and leakage modeling FMs. PTV coverage and/or OAR sparing was compromised in all FMs introduced in phantom plans with the exception of CT number to electron density tables, MU linearity, and MLC tongue-and-groove modeling. Physical measurements did not entirely agree with treatment planning results. For example, symmetry errors resulted in the largest physically measured discrepancies of up to 3% in the PTVs while a maximum of 0.5% deviation was seen in the treatment planning studies. Patient treatment plan study results are under analysis. Conclusion: Even in the simplistic anatomy of the IROC phantom, some basic physics FMs, just outside of TG-142 tolerance criteria, appear to have the potential for large clinical implications.« less

Elastic Rock Heterogeneity Controls Brittle Rock Failure during Hydraulic Fracturing

NASA Astrophysics Data System (ADS)

Langenbruch, C.; Shapiro, S. A.

2014-12-01

For interpretation and inversion of microseismic data it is important to understand, which properties of the reservoir rock control the occurrence probability of brittle rock failure and associated seismicity during hydraulic stimulation. This is especially important, when inverting for key properties like permeability and fracture conductivity. Although it became accepted that seismic events are triggered by fluid flow and the resulting perturbation of the stress field in the reservoir rock, the magnitude of stress perturbations, capable of triggering failure in rocks, can be highly variable. The controlling physical mechanism of this variability is still under discussion. We compare the occurrence of microseismic events at the Cotton Valley gas field to elastic rock heterogeneity, obtained from measurements along the treatment wells. The heterogeneity is characterized by scale invariant fluctuations of elastic properties. We observe that the elastic heterogeneity of the rock formation controls the occurrence of brittle failure. In particular, we find that the density of events is increasing with the Brittleness Index (BI) of the rock, which is defined as a combination of Young's modulus and Poisson's ratio. We evaluate the physical meaning of the BI. By applying geomechanical investigations we characterize the influence of fluctuating elastic properties in rocks on the probability of brittle rock failure. Our analysis is based on the computation of stress fluctuations caused by elastic heterogeneity of rocks. We find that elastic rock heterogeneity causes stress fluctuations of significant magnitude. Moreover, the stress changes necessary to open and reactivate fractures in rocks are strongly related to fluctuations of elastic moduli. Our analysis gives a physical explanation to the observed relation between elastic heterogeneity of the rock formation and the occurrence of brittle failure during hydraulic reservoir stimulations. A crucial factor for understanding seismicity in unconventional reservoirs is the role of anisotropy of rocks. We evaluate an elastic VTI rock model corresponding to a shale gas reservoir in the Horn River Basin to understand the relation between stress, event occurrence and elastic heterogeneity in anisotropic rocks.

Developing a CD-CBM Anticipatory Approach for Cavitation - Defining a Model-Based Descriptor Consistent Across Processes, Phase 1 Final Report Context-Dependent Prognostics and Health Assessment: A New Paradigm for Condition-based Maintenance SBIR Topic No. N98-114

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allgood, G.O.; Dress, W.B.; Kercel, S.W.

1999-06-01

The objective of this research, and subsequent testing, was to identify specific features of cavitation that could be used as a model-based descriptor in a context-dependent condition-based maintenance (CD-CBM) anticipatory prognostic and health assessment model. This descriptor is based on the physics of the phenomena, capturing the salient features of the process dynamics. The test methodology and approach were developed to make the cavitation features the dominant effect in the process and collected signatures. This would allow the accurate characterization of the salient cavitation features at different operational states. By developing such an abstraction, these attributes can be used asmore » a general diagnostic for a system or any of its components. In this study, the particular focus will be pumps. As many as 90% of pump failures are catastrophic. They seem to be operating normally and fail abruptly without warning. This is true whether the failure is sudden hardware damage requiring repair, such as a gasket failure, or a transition into an undesired operating mode, such as cavitation. This means that conventional diagnostic methods fail to predict 90% of incipient failures and that in addressing this problem, model-based methods can add value where it is actually needed.« less

Critical elements of clinical follow-up after hospital discharge for heart failure: insights from the EVEREST trial

PubMed Central

Dunlay, Shannon M.; Gheorghiade, Mihai; Reid, Kimberly J.; Allen, Larry A.; Chan, Paul S.; Hauptman, Paul J.; Zannad, Faiez; Maggioni, Aldo P.; Swedberg, Karl; Konstam, Marvin A.; Spertus, John A.

2010-01-01

Aims Hospitalized heart failure (HF) patients are at high risk for death and readmission. We examined the incremental value of data obtained 1 week after HF hospital discharge in predicting mortality and readmission. Methods and results In the Efficacy of Vasopressin Antagonism in Heart Failure Outcome Study with tolvaptan, 1528 hospitalized patients (ejection fraction ≤40%) with a physical examination, laboratories, and health status [Kansas City Cardiomyopathy Questionnaire (KCCQ)] assessments 1 week after discharge were included. The ability to predict 1 year cardiovascular rehospitalization and mortality was assessed with Cox models, c-statistics, and the integrated discrimination improvement (IDI). Not using a beta-blocker, rales, pedal oedema, hyponatraemia, lower creatinine clearance, higher brain natriuretic peptide, and worse health status were independent risk factors for rehospitalization and death. The c-statistic for the base model (history and medications) was 0.657. The model improved with physical examination, laboratory, and KCCQ results, with IDI increases of 4.9, 7.0, and 3.2%, respectively (P < 0.001 each). The combination of all three offered the greatest incremental gain (c-statistic 0.749; IDI increase 10.8%). Conclusion Physical examination, laboratories, and KCCQ assessed 1 week after discharge offer important prognostic information, suggesting that all are critical components of outpatient evaluation after HF hospitalization. PMID:20197265

Interprofessional communication failures in acute care chains: How can we identify the causes?

PubMed

van Leijen-Zeelenberg, Janneke E; van Raak, Arno J A; Duimel-Peeters, Inge G P; Kroese, Mariëlle E A L; Brink, Peter R G; Vrijhoef, Hubertus J M

2015-01-01

Although communication failures between professionals in acute care delivery occur, explanations for these failures remain unclear. We aim to gain a deeper understanding of interprofessional communication failures by assessing two different explanations for them. A multiple case study containing six cases (i.e. acute care chains) was carried out in which semi-structured interviews, physical artifacts and archival records were used for data collection. Data were entered into matrices and the pattern-matching technique was used to examine the two complementary propositions. Based on the level of standardization and integration present in the acute care chains, the six acute care chains could be divided into two categories of care processes, with the care chains equally distributed among the categories. Failures in communication occurred in both groups. Communication routines were embedded within organizations and descriptions of communication routines in the entire acute care chain could not be found. Based on the results, failures in communication could not exclusively be explained by literature on process typology. Literature on organizational routines was useful to explain the occurrence of communication failures in the acute care chains. Organizational routines can be seen as repetitive action patterns and play an important role in organizations, as most processes are carried out by means of routines. The results of this study imply that it is useful to further explore the role of organizational routines on interprofessional communication in acute care chains to develop a solution for failures in handover practices.

Telemetry Option in the Measurement of Physical Activity for Patients with Heart Failure

ERIC Educational Resources Information Center

Melczer, Csaba; Melczer, László; Oláh, András; Sélleyné-Gyúró, Mónika; Welker, Zsanett; Ács, Pongrác

2015-01-01

Measurement of physical activity among patients with heart failure typically requires a special approach due to the patients' physical status. Nowadays, a technology is already available that can measure the kinematic movements in 3-D by a pacemaker and implantable defibrillator giving an assessment on software. The telemetry data can be…

An integrated approach coupling physically based models and probabilistic method to assess quantitatively landslide susceptibility at different scale: application to different geomorphological environments

NASA Astrophysics Data System (ADS)

Vandromme, Rosalie; Thiéry, Yannick; Sedan, Olivier; Bernardie, Séverine

2016-04-01

Landslide hazard assessment is the estimation of a target area where landslides of a particular type, volume, runout and intensity may occur within a given period. The first step to analyze landslide hazard consists in assessing the spatial and temporal failure probability (when the information is available, i.e. susceptibility assessment). Two types of approach are generally recommended to achieve this goal: (i) qualitative approach (i.e. inventory based methods and knowledge data driven methods) and (ii) quantitative approach (i.e. data-driven methods or deterministic physically based methods). Among quantitative approaches, deterministic physically based methods (PBM) are generally used at local and/or site-specific scales (1:5,000-1:25,000 and >1:5,000, respectively). The main advantage of these methods is the calculation of probability of failure (safety factor) following some specific environmental conditions. For some models it is possible to integrate the land-uses and climatic change. At the opposite, major drawbacks are the large amounts of reliable and detailed data (especially materials type, their thickness and the geotechnical parameters heterogeneity over a large area) and the fact that only shallow landslides are taking into account. This is why they are often used at site-specific scales (> 1:5,000). Thus, to take into account (i) materials' heterogeneity , (ii) spatial variation of physical parameters, (iii) different landslide types, the French Geological Survey (i.e. BRGM) has developed a physically based model (PBM) implemented in a GIS environment. This PBM couples a global hydrological model (GARDENIA®) including a transient unsaturated/saturated hydrological component with a physically based model computing the stability of slopes (ALICE®, Assessment of Landslides Induced by Climatic Events) based on the Morgenstern-Price method for any slip surface. The variability of mechanical parameters is handled by Monte Carlo approach. The probability to obtain a safety factor below 1 represents the probability of occurrence of a landslide for a given triggering event. The dispersion of the distribution gives the uncertainty of the result. Finally, a map is created, displaying a probability of occurrence for each computing cell of the studied area. In order to take into account the land-uses change, a complementary module integrating the vegetation effects on soil properties has been recently developed. Last years, the model has been applied at different scales for different geomorphological environments: (i) at regional scale (1:50,000-1:25,000) in French West Indies and French Polynesian islands (ii) at local scale (i.e.1:10,000) for two complex mountainous areas; (iii) at the site-specific scale (1:2,000) for one landslide. For each study the 3D geotechnical model has been adapted. The different studies have allowed : (i) to discuss the different factors included in the model especially the initial 3D geotechnical models; (ii) to precise the location of probable failure following different hydrological scenarii; (iii) to test the effects of climatic change and land-use on slopes for two cases. In that way, future changes in temperature, precipitation and vegetation cover can be analyzed, permitting to address the impacts of global change on landslides. Finally, results show that it is possible to obtain reliable information about future slope failures at different scale of work for different scenarii with an integrated approach. The final information about landslide susceptibility (i.e. probability of failure) can be integrated in landslide hazard assessment and could be an essential information source for future land planning. As it has been performed in the ANR Project SAMCO (Society Adaptation for coping with Mountain risks in a global change COntext), this analysis constitutes a first step in the chain for risk assessment for different climate and economical development scenarios, to evaluate the resilience of mountainous areas.

Failure mechanisms of fibrin-based surgical tissue adhesives

NASA Astrophysics Data System (ADS)

Sierra, David Hugh

A series of studies was performed to investigate the potential impact of heterogeneity in the matrix of multiple-component fibrin-based tissue adhesives upon their mechanical and biomechanical properties both in vivo and in vitro. Investigations into the failure mechanisms by stereological techniques demonstrated that heterogeneity could be measured quantitatively and that the variation in heterogeneity could be altered both by the means of component mixing and delivery and by the formulation of the sealant. Ex vivo tensile adhesive strength was found to be inversely proportional to the amount of heterogeneity. In contrast, in vivo tensile wound-closure strength was found to be relatively unaffected by the degree of heterogeneity, while in vivo parenchymal organ hemostasis in rabbits was found to be affected: greater heterogeneity appeared to correlate with an increase in hemostasis time and amount of sealant necessary to effect hemostasis. Tensile testing of the bulk sealant showed that mechanical parameters were proportional to fibrin concentration and that the physical characteristics of the failure supported a ductile mechanism. Strain hardening as a function of percentage of strain, and strain rate was observed for both concentrations, and syneresis was observed at low strain rates for the lower fibrin concentration. Blister testing demonstrated that burst pressure and failure energy were proportional to fibrin concentration and decreased with increasing flow rate. Higher fibrin concentration demonstrated predominately compact morphology debonds with cohesive failure loci, demonstrating shear or viscous failure in a viscoelastic rubbery adhesive. The lower fibrin concentration sealant exhibited predominately fractal morphology debonds with cohesive failure loci, supporting an elastoviscous material condition. The failure mechanism for these was hypothesized and shown to be flow-induced ductile fracture. Based on these findings, the failure mechanism was stochastic in nature because the mean failure energy and burst pressure values were not predictive of locus and morphology. Instead, flow rate and fibrin concentration showed the most predictive value, with the outcome best described as a probability distribution rather than a specific deterministic outcome.

Micromechanical investigation of ductile failure in Al 5083-H116 via 3D unit cell modeling

NASA Astrophysics Data System (ADS)

Bomarito, G. F.; Warner, D. H.

2015-01-01

Ductile failure is governed by the evolution of micro-voids within a material. The micro-voids, which commonly initiate at second phase particles within metal alloys, grow and interact with each other until failure occurs. The evolution of the micro-voids, and therefore ductile failure, depends on many parameters (e.g., stress state, temperature, strain rate, void and particle volume fraction, etc.). In this study, the stress state dependence of the ductile failure of Al 5083-H116 is investigated by means of 3-D Finite Element (FE) periodic cell models. The cell models require only two pieces of information as inputs: (1) the initial particle volume fraction of the alloy and (2) the constitutive behavior of the matrix material. Based on this information, cell models are subjected to a given stress state, defined by the stress triaxiality and the Lode parameter. For each stress state, the cells are loaded in many loading orientations until failure. Material failure is assumed to occur in the weakest orientation, and so the orientation in which failure occurs first is considered as the critical orientation. The result is a description of material failure that is derived from basic principles and requires no fitting parameters. Subsequently, the results of the simulations are used to construct a homogenized material model, which is used in a component-scale FE model. The component-scale FE model is compared to experiments and is shown to over predict ductility. By excluding smaller nucleation events and load path non-proportionality, it is concluded that accuracy could be gained by including more information about the true microstructure in the model; emphasizing that its incorporation into micromechanical models is critical to developing quantitatively accurate physics-based ductile failure models.

Daily physical activity in stable heart failure patients.

PubMed

Dontje, Manon L; van der Wal, Martje H L; Stolk, Ronald P; Brügemann, Johan; Jaarsma, Tiny; Wijtvliet, Petra E P J; van der Schans, Cees P; de Greef, Mathieu H G

2014-01-01

Physical activity is the only nonpharmacological therapy that is proven to be effective in heart failure (HF) patients in reducing morbidity. To date, little is known about the levels of daily physical activity in HF patients and about related factors. The objectives of this study were to (a) describe performance-based daily physical activity in HF patients, (b) compare it with physical activity guidelines, and (c) identify related factors of daily physical activity. The daily physical activity of 68 HF patients was measured using an accelerometer (SenseWear) for 48 hours. Psychological characteristics (self-efficacy, motivation, and depression) were measured using questionnaires. To have an indication how to interpret daily physical activity levels of the study sample, time spent on moderate- to vigorous-intensity physical activities was compared with the 30-minute activity guideline. Steps per day was compared with the criteria for healthy adults, in the absence of HF-specific criteria. Linear regression analyses were used to identify related factors of daily physical activity. Forty-four percent were active for less than 30 min/d, whereas 56% were active for more than 30 min/d. Fifty percent took fewer than 5000 steps per day, 35% took 5000 to 10 000 steps per day, and 15% took more than 10 000 steps per day. Linear regression models showed that New York Heart Association classification and self-efficacy were the most important factors explaining variance in daily physical activity. The variance in daily physical activity in HF patients is considerable. Approximately half of the patients had a sedentary lifestyle. Higher New York Heart Association classification and lower self-efficacy are associated with less daily physical activity. These findings contribute to the understanding of daily physical activity behavior of HF patients and can help healthcare providers to promote daily physical activity in sedentary HF patients.

An Appropriate Population for Acute Inpatient Rehabilitation? A Case Series of Three Patients With Advanced Heart Failure on Continuous Inotropic Support.

PubMed

McCormick, Zachary L; Chu, Samuel K; Goodman, Daniel; Oswald, Matthew; Reger, Christopher; Sliwa, James

2015-06-01

The number of individuals with heart failure and the treatment modalities available to manage heart failure are increasing. Continuous inotropic support is a treatment modality used in cases of severe heart failure. Although most patients initiated on continuous inotropic support are discharged home, those with greater functional compromise, comorbid conditions that cause disability, or other significant medical complexity may be referred to acute inpatient rehabilitation. The feasibility and benefits of acute inpatient rehabilitation in this population, however, has yet to be investigated. We report the functional progress and medical complications of 3 patients on continuous inotropic support who participated in acute inpatient rehabilitation. The patients demonstrated varying levels of success, highlighting a need for evidence-based, preadmission screening criteria for this population. Copyright © 2015 American Academy of Physical Medicine and Rehabilitation. Published by Elsevier Inc. All rights reserved.

The Usability of Rock-Like Materials for Numerical Studies on Rocks

NASA Astrophysics Data System (ADS)

Zengin, Enes; Abiddin Erguler, Zeynal

2017-04-01

The approaches of synthetic rock material and mass are widely used by many researchers for understanding the failure behavior of different rocks. In order to model the failure behavior of rock material, researchers take advantageous of different techniques and software. But, the majority of all these instruments are based on distinct element method (DEM). For modeling the failure behavior of rocks, and so to create a fundamental synthetic rock material model, it is required to perform related laboratory experiments for providing strength parameters. In modelling studies, model calibration processes are performed by using parameters of intact rocks such as porosity, grain size, modulus of elasticity and Poisson ratio. In some cases, it can be difficult or even impossible to acquire representative rock samples for laboratory experiments from heavily jointed rock masses and vuggy rocks. Considering this limitation, in this study, it was aimed to investigate the applicability of rock-like material (e.g. concrete) to understand and model the failure behavior of rock materials having complex inherent structures. For this purpose, concrete samples having a mixture of %65 cement dust and %35 water were utilized. Accordingly, intact concrete samples representing rocks were prepared in laboratory conditions and their physical properties such as porosity, pore size and density etc. were determined. In addition, to acquire the mechanical parameters of concrete samples, uniaxial compressive strength (UCS) tests were also performed by simultaneously measuring strain during testing. The measured physical and mechanical properties of these extracted concrete samples were used to create synthetic material and then uniaxial compressive tests were modeled and performed by using two dimensional discontinuum program known as Particle Flow Code (PFC2D). After modeling studies in PFC2D, approximately similar failure mechanism and testing results were achieved from both experimental and artificial simulations. The results obtained from these laboratory tests and modelling studies were compared with the other researcher's studies in respect to failure mechanism of different type of rocks. It can be concluded that there is similar failure mechanism between concrete and rock materials. Therefore, the results obtained from concrete samples that would be prepared at different porosity and pore sizes can be used in future studies in selection micro-mechanical and physical properties to constitute synthetic rock materials for understanding failure mechanism of rocks having complex inherent structures such as vuggy rocks or heavily jointed rock masses.

An experimental evaluation of software redundancy as a strategy for improving reliability

NASA Technical Reports Server (NTRS)

Eckhardt, Dave E., Jr.; Caglayan, Alper K.; Knight, John C.; Lee, Larry D.; Mcallister, David F.; Vouk, Mladen A.; Kelly, John P. J.

1990-01-01

The strategy of using multiple versions of independently developed software as a means to tolerate residual software design faults is suggested by the success of hardware redundancy for tolerating hardware failures. Although, as generally accepted, the independence of hardware failures resulting from physical wearout can lead to substantial increases in reliability for redundant hardware structures, a similar conclusion is not immediate for software. The degree to which design faults are manifested as independent failures determines the effectiveness of redundancy as a method for improving software reliability. Interest in multi-version software centers on whether it provides an adequate measure of increased reliability to warrant its use in critical applications. The effectiveness of multi-version software is studied by comparing estimates of the failure probabilities of these systems with the failure probabilities of single versions. The estimates are obtained under a model of dependent failures and compared with estimates obtained when failures are assumed to be independent. The experimental results are based on twenty versions of an aerospace application developed and certified by sixty programmers from four universities. Descriptions of the application, development and certification processes, and operational evaluation are given together with an analysis of the twenty versions.

Accelerated Aging System for Prognostics of Power Semiconductor Devices

NASA Technical Reports Server (NTRS)

Celaya, Jose R.; Vashchenko, Vladislav; Wysocki, Philip; Saha, Sankalita

2010-01-01

Prognostics is an engineering discipline that focuses on estimation of the health state of a component and the prediction of its remaining useful life (RUL) before failure. Health state estimation is based on actual conditions and it is fundamental for the prediction of RUL under anticipated future usage. Failure of electronic devices is of great concern as future aircraft will see an increase of electronics to drive and control safety-critical equipment throughout the aircraft. Therefore, development of prognostics solutions for electronics is of key importance. This paper presents an accelerated aging system for gate-controlled power transistors. This system allows for the understanding of the effects of failure mechanisms, and the identification of leading indicators of failure which are essential in the development of physics-based degradation models and RUL prediction. In particular, this system isolates electrical overstress from thermal overstress. Also, this system allows for a precise control of internal temperatures, enabling the exploration of intrinsic failure mechanisms not related to the device packaging. By controlling the temperature within safe operation levels of the device, accelerated aging is induced by electrical overstress only, avoiding the generation of thermal cycles. The temperature is controlled by active thermal-electric units. Several electrical and thermal signals are measured in-situ and recorded for further analysis in the identification of leading indicators of failures. This system, therefore, provides a unique capability in the exploration of different failure mechanisms and the identification of precursors of failure that can be used to provide a health management solution for electronic devices.

Quality of Life for Saudi Patients With Heart Failure: A Cross-Sectional Correlational Study.

PubMed

AbuRuz, Mohannad Eid; Alaloul, Fawwaz; Saifan, Ahmed; Masa'deh, Rami; Abusalem, Said

2015-06-25

Heart failure is a major public health issue and a growing concern in developing countries, including Saudi Arabia. Most related research was conducted in Western cultures and may have limited applicability for individuals in Saudi Arabia. Thus, this study assesses the quality of life of Saudi patients with heart failure. A cross-sectional correlational design was used on a convenient sample of 103 patients with heart failure. Data were collected using the Short Form-36 and the Medical Outcomes Study-Social Support Survey. Overall, the patients' scores were low for all domains of Quality of Life. The Physical Component Summary and Mental Component Summary mean scores and SDs were (36.7±12.4, 48.8±6.5) respectively, indicating poor Quality of Life. Left ventricular ejection fraction was the strongest predictor of both physical and mental summaries. Identifying factors that impact quality of life for Saudi heart failure patients is important in identifying and meeting their physical and psychosocial needs.

Use of a pretest strategy for physical therapist assistant programs to predict success rate on the national physical therapy exam.

PubMed

Sloas, Stacey B; Keith, Becky; Whitehead, Malcolm T

2013-01-01

This study investigated a pretest strategy that identified physical therapist assistant (PTA) students who were at risk of failure on the National Physical Therapy Examination (NPTE). Program assessment data from five cohorts of PTA students (2005-2009) were used to develop a stepwise multiple regression formula that predicted first-time NPTE licensure scores. Data used included the Nelson-Denny Reading Test, grades from eight core courses, grade point average upon admission to the program, and scores from three mock NPTE exams given during the program. Pearson correlation coefficients were calculated between each of the 15 variables and NPTE scores. Stepwise multiple regression analysis was performed using data collected at the ends of the first, second, and third (final) semesters of the program. Data from the class of 2010 were then used to validate the formula. The end-of-program formula accounted for the greatest variance (57%) in predicted scores. Those students scoring below a predicted scaled score of 620 were identified to be at risk of failure of the licensure exam. These students were counseled, and a remedial plan was developed based on regression predictions prior to them sitting for the licensure exam.

Survey of critical failure events in on-chip interconnect by fault tree analysis

NASA Astrophysics Data System (ADS)

Yokogawa, Shinji; Kunii, Kyousuke

2018-07-01

In this paper, a framework based on reliability physics is proposed for adopting fault tree analysis (FTA) to the on-chip interconnect system of a semiconductor. By integrating expert knowledge and experience regarding the possibilities of failure on basic events, critical issues of on-chip interconnect reliability will be evaluated by FTA. In particular, FTA is used to identify the minimal cut sets with high risk priority. Critical events affecting the on-chip interconnect reliability are identified and discussed from the viewpoint of long-term reliability assessment. The moisture impact is evaluated as an external event.

Probabilistic Design Analysis (PDA) Approach to Determine the Probability of Cross-System Failures for a Space Launch Vehicle

NASA Technical Reports Server (NTRS)

Shih, Ann T.; Lo, Yunnhon; Ward, Natalie C.

2010-01-01

Quantifying the probability of significant launch vehicle failure scenarios for a given design, while still in the design process, is critical to mission success and to the safety of the astronauts. Probabilistic risk assessment (PRA) is chosen from many system safety and reliability tools to verify the loss of mission (LOM) and loss of crew (LOC) requirements set by the NASA Program Office. To support the integrated vehicle PRA, probabilistic design analysis (PDA) models are developed by using vehicle design and operation data to better quantify failure probabilities and to better understand the characteristics of a failure and its outcome. This PDA approach uses a physics-based model to describe the system behavior and response for a given failure scenario. Each driving parameter in the model is treated as a random variable with a distribution function. Monte Carlo simulation is used to perform probabilistic calculations to statistically obtain the failure probability. Sensitivity analyses are performed to show how input parameters affect the predicted failure probability, providing insight for potential design improvements to mitigate the risk. The paper discusses the application of the PDA approach in determining the probability of failure for two scenarios from the NASA Ares I project

Child Neglect in the Military Community: Are We Neglecting the Child?

DTIC Science & Technology

1995-04-01

encompasses "a parent’s or other caretaker’s failure to provide basic physical health care, supervision, nutrition, personal hygiene, emotional nurturing...the term "child neglect" generally refers to: emotional neglect, abandonment, and the failure to provide: food, shelter, clothing, medical care...Resource Center on Child Abuse and Neglect 26-- divides child neglect into four types: physical, educational, emotional , and medical. Physical neglect

An in-depth, longitudinal examination of the daily physical activity of a patient with heart failure using a Nintendo Wii at home: a case report.

PubMed

Klompstra, Leonie Verheijden; Jaarsma, Tiny; Strömberg, Anna

2013-06-01

To explore the influence of the Nintendo Wii on the daily physical activity of a patient with chronic heart failure at home. A 74-year-old Swedish patient with heart failure had access to a Nintendo Wii at home for 12 weeks. Exercise motivation, exercise self-efficacy and exercise capacity were assessed before and after the intervention. Data on perceived physical effort, global well-being and expended energy were collected every day during the intervention. During the 12 weeks of access to the Nintendo Wii, daily physical activity increased by 200% on weekdays and 57% on weekends, compared with baseline. The patient's exercise motivation and exercise self-efficacy increased during the study, whereas perceived physical effort and global well-being did not change. The patient had no difficulties in using the system and did not suffer any major harm. The results of this case study suggest that providing patients with heart failure access to a Nintendo Wii is a promising and safe intervention. The energy expended by the patient per day increased, as did exercise capacity. Playing the Nintendo Wii did not increase the perceived physical effort, but increased motivation to exercise and decreased barriers to exercising.

The failure of earthquake failure models

USGS Publications Warehouse

Gomberg, J.

2001-01-01

In this study I show that simple heuristic models and numerical calculations suggest that an entire class of commonly invoked models of earthquake failure processes cannot explain triggering of seismicity by transient or "dynamic" stress changes, such as stress changes associated with passing seismic waves. The models of this class have the common feature that the physical property characterizing failure increases at an accelerating rate when a fault is loaded (stressed) at a constant rate. Examples include models that invoke rate state friction or subcritical crack growth, in which the properties characterizing failure are slip or crack length, respectively. Failure occurs when the rate at which these grow accelerates to values exceeding some critical threshold. These accelerating failure models do not predict the finite durations of dynamically triggered earthquake sequences (e.g., at aftershock or remote distances). Some of the failure models belonging to this class have been used to explain static stress triggering of aftershocks. This may imply that the physical processes underlying dynamic triggering differs or that currently applied models of static triggering require modification. If the former is the case, we might appeal to physical mechanisms relying on oscillatory deformations such as compaction of saturated fault gouge leading to pore pressure increase, or cyclic fatigue. However, if dynamic and static triggering mechanisms differ, one still needs to ask why static triggering models that neglect these dynamic mechanisms appear to explain many observations. If the static and dynamic triggering mechanisms are the same, perhaps assumptions about accelerating failure and/or that triggering advances the failure times of a population of inevitable earthquakes are incorrect.

The association between physical activity and social isolation in community-dwelling older adults.

PubMed

Robins, Lauren M; Hill, Keith D; Finch, Caroline F; Clemson, Lindy; Haines, Terry

2018-02-01

Social isolation is an increasing concern in older community-dwelling adults. There is growing need to determine effective interventions addressing social isolation. This study aimed to determine whether a relationship exists between physical activity (recreational and/or household-based) and social isolation. An examination was conducted for whether group- or home-based falls prevention exercise was associated with social isolation. Cross-sectional analysis of telephone survey data was used to investigate relationships between physical activity, health, age, gender, living arrangements, ethnicity and participation in group- or home-based falls prevention exercise on social isolation. Univariable and multivariable ordered logistic regression analyses were conducted. Factors found to be significantly associated with reduced social isolation in multivariable analysis included living with a partner/spouse, reporting better general health, higher levels of household-based physical activity (OR = 1.03, CI = 1.01-1.05) and feeling less downhearted/depressed. Being more socially isolated was associated with symptoms of depression and a diagnosis of congestive heart failure (pseudo R 2 = 0.104). Findings suggest that household-based physical activity is related to social isolation in community-dwelling older adults. Further research is required to determine the nature of this relationship and to investigate the impact of group physical activity interventions on social isolation.

Explosion/Blast Dynamics for Constellation Launch Vehicles Assessment

NASA Technical Reports Server (NTRS)

Baer, Mel; Crawford, Dave; Hickox, Charles; Kipp, Marlin; Hertel, Gene; Morgan, Hal; Ratzel, Arthur; Cragg, Clinton H.

2009-01-01

An assessment methodology is developed to guide quantitative predictions of adverse physical environments and the subsequent effects on the Ares-1 crew launch vehicle associated with the loss of containment of cryogenic liquid propellants from the upper stage during ascent. Development of the methodology is led by a team at Sandia National Laboratories (SNL) with guidance and support from a number of National Aeronautics and Space Administration (NASA) personnel. The methodology is based on the current Ares-1 design and feasible accident scenarios. These scenarios address containment failure from debris impact or structural response to pressure or blast loading from an external source. Once containment is breached, the envisioned assessment methodology includes predictions for the sequence of physical processes stemming from cryogenic tank failure. The investigative techniques, analysis paths, and numerical simulations that comprise the proposed methodology are summarized and appropriate simulation software is identified in this report.

Towards Prognostics of Power MOSFETs: Accelerated Aging and Precursors of Failure

NASA Technical Reports Server (NTRS)

Celaya, Jose R.; Saxena, Abhinav; Wysocki, Philip; Saha, Sankalita; Goebel, Kai

2010-01-01

This paper presents research results dealing with power MOSFETs (metal oxide semiconductor field effect transistor) within the prognostics and health management of electronics. Experimental results are presented for the identification of the on-resistance as a precursor to failure of devices with die-attach degradation as a failure mechanism. Devices are aged under power cycling in order to trigger die-attach damage. In situ measurements of key electrical and thermal parameters are collected throughout the aging process and further used for analysis and computation of the on-resistance parameter. Experimental results show that the devices experience die-attach damage and that the on-resistance captures the degradation process in such a way that it could be used for the development of prognostics algorithms (data-driven or physics-based).

Conduit Stability and Collapse in Explosive Volcanic Eruptions: Coupling Conduit Flow and Failure Models

NASA Astrophysics Data System (ADS)

Mullet, B.; Segall, P.

2017-12-01

Explosive volcanic eruptions can exhibit abrupt changes in physical behavior. In the most extreme cases, high rates of mass discharge are interspaced by dramatic drops in activity and periods of quiescence. Simple models predict exponential decay in magma chamber pressure, leading to a gradual tapering of eruptive flux. Abrupt changes in eruptive flux therefore indicate that relief of chamber pressure cannot be the only control of the evolution of such eruptions. We present a simplified physics-based model of conduit flow during an explosive volcanic eruption that attempts to predict stress-induced conduit collapse linked to co-eruptive pressure loss. The model couples a simple two phase (gas-melt) 1-D conduit solution of the continuity and momentum equations with a Mohr-Coulomb failure condition for the conduit wall rock. First order models of volatile exsolution (i.e. phase mass transfer) and fragmentation are incorporated. The interphase interaction force changes dramatically between flow regimes, so smoothing of this force is critical for realistic results. Reductions in the interphase force lead to significant relative phase velocities, highlighting the deficiency of homogenous flow models. Lateral gas loss through conduit walls is incorporated using a membrane-diffusion model with depth dependent wall rock permeability. Rapid eruptive flux results in a decrease of chamber and conduit pressure, which leads to a critical deviatoric stress condition at the conduit wall. Analogous stress distributions have been analyzed for wellbores, where much work has been directed at determining conditions that lead to wellbore failure using Mohr-Coulomb failure theory. We extend this framework to cylindrical volcanic conduits, where large deviatoric stresses can develop co-eruptively leading to multiple distinct failure regimes depending on principal stress orientations. These failure regimes are categorized and possible implications for conduit flow are discussed, including cessation of eruption.

Heart Failure

MedlinePlus

... cause heart failure, such as coronary artery disease, high blood pressure, diabetes or obesity. Symptoms Heart failure can be ongoing ( ... include: Not smoking Controlling certain conditions, such as high blood pressure and diabetes Staying physically active Eating healthy foods Maintaining a ...

Physics-Based Fragment Acceleration Modeling for Pressurized Tank Burst Risk Assessments

NASA Technical Reports Server (NTRS)

Manning, Ted A.; Lawrence, Scott L.

2014-01-01

As part of comprehensive efforts to develop physics-based risk assessment techniques for space systems at NASA, coupled computational fluid and rigid body dynamic simulations were carried out to investigate the flow mechanisms that accelerate tank fragments in bursting pressurized vessels. Simulations of several configurations were compared to analyses based on the industry-standard Baker explosion model, and were used to formulate an improved version of the model. The standard model, which neglects an external fluid, was found to agree best with simulation results only in configurations where the internal-to-external pressure ratio is very high and fragment curvature is small. The improved model introduces terms that accommodate an external fluid and better account for variations based on circumferential fragment count. Physics-based analysis was critical in increasing the model's range of applicability. The improved tank burst model can be used to produce more accurate risk assessments of space vehicle failure modes that involve high-speed debris, such as exploding propellant tanks and bursting rocket engines.

Autonomic dysfunction predicts poor physical improvement after cardiac rehabilitation in patients with heart failure.

PubMed

Compostella, Leonida; Nicola, Russo; Tiziana, Setzu; Caterina, Compostella; Fabio, Bellotto

2014-11-01

Cardiac autonomic dysfunction, clinically expressed by reduced heart rate variability (HRV), is present in patients with congestive heart failure (CHF) and is related to the degree of left ventricular dysfunction. In athletes, HRV is an indicator of ability to improve performance. No similar data are available for CHF. The aim of this study was to assess whether HRV could predict the capability of CHF patients to improve physical fitness after a short period of exercise-based cardiac rehabilitation (CR). This was an observational, non-randomized study, conducted on 57 patients with advanced CHF, admitted to a residential cardiac rehabilitation unit 32 ± 22 days after an episode of acute heart failure. Inclusion criteria were sinus rhythm, stable clinical conditions, no diabetes and ejection fraction ≤ 35%. HRV (time-domain) and mean and minimum heart rate (HR) were evaluated using 24-h Holter at admission. Patients' physical fitness was evaluated at admission by 6-minute walking test (6MWT) and reassessed after two weeks of intensive exercise-based CR. Exercise capacity was evaluated by a symptom-limited cardiopulmonary exercise test (CPET). Patients with very depressed HRV (SDNN 55.8 ± 10.0 ms) had no improvement in their walking capacity after short CR, walked shorter absolute distances at final 6MWT (348 ± 118 vs. 470 ± 109 m; P = 0.027) and developed a peak-VO2 at CPET significantly lower than patients with greater HRV parameters (11.4 ± 3.7 vs. an average > 16 ± 4 mL/kg/min). Minimum HR, but not mean HR, showed a negative correlation (ρ = -0.319) with CPET performance. In patients with advanced CHF, depressed HRV and higher minimum HR were predictors of poor working capacity after a short period of exercise-based CR. An individualized and intensive rehabilitative intervention should be considered for these patients.

Hitherto unknown shear rupture mechanism as a source of instability in intact hard rocks at highly confined compression

NASA Astrophysics Data System (ADS)

Tarasov, Boris G.

2014-05-01

Today, frictional shear resistance along pre-existing faults is considered to be the lower limit on rock shear strength for confined conditions corresponding to the seismogenic layer. This paper introduces a recently identified shear rupture mechanism providing a paradoxical feature of hard rocks - the possibility of shear rupture propagation through the highly confined intact rock mass at shear stress levels significantly less than frictional strength. In the new mechanism, the rock failure associated with consecutive creation of small slabs (known as ‘domino-blocks') from the intact rock in the rupture tip is driven by a fan-shaped domino structure representing the rupture head. The fan-head combines such unique features as: extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Due to this the failure process caused by the mechanism is very dynamic and violent. This makes it impossible to directly observe and study the mechanism and can explain why the mechanism has not been detected before. This paper provides physical motivation for the mechanism, based upon side effects accompanying the failure process. Physical and mathematical models of the mechanism presented in the paper explain unique and paradoxical features of the mechanism. The new shear rupture mechanism allows a novel point of view for understanding the nature of spontaneous failure processes in hard rocks including earthquakes.

Risk assessment for Industrial Control Systems quantifying availability using mean failure cost (MFC)

DOE PAGES

Chen, Qian; Abercrombie, Robert K; Sheldon, Frederick T.

2015-09-23

Industrial Control Systems (ICS) are commonly used in industries such as oil and natural gas, transportation, electric, water and wastewater, chemical, pharmaceutical, pulp and paper, food and beverage, as well as discrete manufacturing (e.g., automotive, aerospace, and durable goods.) SCADA systems are generally used to control dispersed assets using centralized data acquisition and supervisory control.Originally, ICS implementations were susceptible primarily to local threats because most of their components were located in physically secure areas (i.e., ICS components were not connected to IT networks or systems). The trend toward integrating ICS systems with IT networks (e.g., efficiency and the Internet ofmore » Things) provides significantly less isolation for ICS from the outside world thus creating greater risk due to external threats. Albeit, the availability of ICS/SCADA systems is critical to assuring safety, security and profitability. Such systems form the backbone of our national cyber-physical infrastructure.Herein, we extend the concept of mean failure cost (MFC) to address quantifying availability to harmonize well with ICS security risk assessment. This new measure is based on the classic formulation of Availability combined with Mean Failure Cost (MFC). Finally, the metric offers a computational basis to estimate the availability of a system in terms of the loss that each stakeholder stands to sustain as a result of security violations or breakdowns (e.g., deliberate malicious failures).« less

Rehabilitation Therapy in Older Acute Heart Failure Patients (REHAB-HF) Trial: Design and Rationale

PubMed Central

Reeves, Gordon R.; Whellan, David J.; Duncan, Pamela; O’Connor, Christopher M.; Pastva, Amy M.; Eggebeen, Joel D; Hewston, Leigh Ann; Morgan, Timothy M.; Reed, Shelby D.; Rejeski, W. Jack; Mentz, Robert J.; Rosenberg, Paul B.; Kitzman, Dalane W.

2017-01-01

Background Acute decompensated heart failure (ADHF) is a leading cause of hospitalization in older persons in the United States. Reduced physical function and frailty are major determinants of adverse outcomes in older patients with hospitalized ADHF. However, these are not addressed by current heart failure (HF) management strategies and there has been little study of exercise training in older, frail HF patients with recent ADHF. Hypothesis Targeting physical frailty with a multi-domain structured physical rehabilitation intervention will improve physical function and reduce adverse outcomes among older patients experiencing a HF hospitalization. Study Design Rehabilitation Therapy in Older Acute Heart Failure Patients (REHAB-HF) is a multi-center clinical trial in which 360 patients ≥ 60 years hospitalized with ADHF will be randomized either to a novel 12-week multi-domain physical rehabilitation intervention or to attention control. The goal of the intervention is to improve balance, mobility, strength and endurance utilizing reproducible, targeted exercises administered by a multi-disciplinary team with specific milestones for progression. The primary study aim is to assess the efficacy of the REHAB-HF intervention on physical function measured by total Short Physical Performance Battery score. The secondary outcome is 6-month all-cause rehospitalization. Additional outcome measures include quality of life and costs. Conclusions REHAB-HF is the first randomized trial of a physical function intervention in older patients with hospitalized ADHF designed to determine if addressing deficits in balance, mobility, strength and endurance improves physical function and reduces rehospitalizations. It will address key evidence gaps concerning the role of physical rehabilitation in the care of older patients, those with ADHF, frailty, and multiple comorbidities. PMID:28267466

Is perceived failure in school performance a trigger of physical injury? A case-crossover study of children in Stockholm County

PubMed Central

Laflamme, L; Engstrom, K; Moller, J; Hallqvist, J

2004-01-01

Objectives: To investigate whether perceived failure in school performance increases the potential for children to be physically injured. Subjects: Children aged 10–15 years residing in the Stockholm County and hospitalised or called back for a medical check up because of a physical injury during the school years 2000–2001 and 2001–2002 (n = 592). Methods: A case-crossover design was used and information on potential injury triggers was gathered by interview. Information about family socioeconomic circumstances was gathered by a questionnaire filled in by parents during the child interview (response rate 87%). Results: Perceived failure in school performance has the potential to trigger injury within up to 10 hours subsequent to exposure (relative risk = 2.70; 95% confidence intervals = 1.2 to 5.8). The risk is significantly higher among pre-adolescents and among children from families at a higher education level. Conclusions: Experiencing feelings of failure may affect children's physical safety, in particular among pre-adolescents. Possible mechanisms are perceptual deficits and response changes occasioned by the stress experienced after exposure. PMID:15082740

The Critical Criterion on Runaway Shear Banding in Metallic Glasses

PubMed Central

Sun, B. A.; Yang, Y.; Wang, W. H.; Liu, C. T.

2016-01-01

The plastic flow of metallic glasses (MGs) in bulk is mediated by nanoscale shear bands, which is known to proceed in a stick-slip manner until reaching a transition state causing catastrophic failures. Such a slip-to-failure transition controls the plasticity of MGs and resembles many important phenomena in natural science and engineering, such as friction, lubrication and earthquake, therefore has attracted tremendous research interest over past decades. However, despite the fundamental and practical importance, the physical origin of this slip-to-failure transition is still poorly understood. By tracking the behavior of a single shear band, here we discover that the final fracture of various MGs during compression is triggered as the velocity of the dominant shear band rises to a critical value, the magnitude of which is independent of alloy composition, sample size, strain rate and testing frame stiffness. The critical shear band velocity is rationalized with the continuum theory of liquid instability, physically originating from a shear-induced cavitation process inside the shear band. Our current finding sheds a quantitative insight into deformation and fracture in disordered solids and, more importantly, is useful to the design of plastic/tough MG-based materials and structures. PMID:26893196

Quality of Life for Saudi Patients With Heart Failure: A Cross-Sectional Correlational Study

PubMed Central

AbuRuz, Mohannad Eid; Alaloul, Fawwaz; Saifan, Ahmed; Masa’Deh, Rami; Abusalem, Said

2016-01-01

Introduction: Heart failure is a major public health issue and a growing concern in developing countries, including Saudi Arabia. Most related research was conducted in Western cultures and may have limited applicability for individuals in Saudi Arabia. Thus, this study assesses the quality of life of Saudi patients with heart failure. Materials and Methods: A cross-sectional correlational design was used on a convenient sample of 103 patients with heart failure. Data were collected using the Short Form-36 and the Medical Outcomes Study-Social Support Survey. Results: Overall, the patients’ scores were low for all domains of Quality of Life. The Physical Component Summary and Mental Component Summary mean scores and SDs were (36.7±12.4, 48.8±6.5) respectively, indicating poor Quality of Life. Left ventricular ejection fraction was the strongest predictor of both physical and mental summaries. Conclusion: Identifying factors that impact quality of life for Saudi heart failure patients is important in identifying and meeting their physical and psychosocial needs. PMID:26493415

Prognostic value of the physical examination in patients with heart failure and atrial fibrillation: insights from the AF-CHF trial (atrial fibrillation and chronic heart failure).

PubMed

Caldentey, Guillem; Khairy, Paul; Roy, Denis; Leduc, Hugues; Talajic, Mario; Racine, Normand; White, Michel; O'Meara, Eileen; Guertin, Marie-Claude; Rouleau, Jean L; Ducharme, Anique

2014-02-01

This study sought to assess the prognostic value of physical examination in a modern treated heart failure population. The physical examination is the cornerstone of the evaluation and monitoring of patients with heart failure. Yet, the prognostic value of congestive signs (i.e., peripheral edema, jugular venous distension, a third heart sound, and pulmonary rales) has not been assessed in the current era. A post-hoc analysis was conducted on all 1,376 patients, 81% male, mean age 67 ± 11 years, with symptomatic left ventricular systolic dysfunction enrolled in the AF-CHF (Atrial Fibrillation and Congestive Heart Failure) trial. The prognostic value of baseline physical examination findings was assessed in univariate and multivariate Cox regression analyses. Peripheral edema was observed in 425 (30.9%), jugular venous distension in 297 (21.6%), a third heart sound in 207 (15.0%), and pulmonary rales in 178 (12.9%) patients. Death from cardiovascular causes occurred in 357 (25.9%) patients over a mean follow-up of 37 ± 19 months. All 4 physical examination findings were associated with cardiovascular mortality in univariate analyses (all p values <0.01). In multivariate analyses, taking all 4 signs as potential covariates, only rales (hazard ratio 1.41; 95% confidence interval: 1.07 to 1.86; p = 0.013) and peripheral edema (hazard ratio: 1.25; 95% confidence interval: 1.00 to 1.57; p = 0.048) were associated with cardiovascular mortality, independent of other variables. In the modern era, congestive signs on the physical examination (i.e., peripheral edema, jugular venous distension, a third heart sound, and pulmonary rales) continue to provide important prognostic information in patients with congestive heart failure. Copyright © 2014 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

8 CFR 214.4 - Denial of certification, denial of recertification or withdrawal of SEVP certification.

Code of Federal Regulations, 2011 CFR

2011-01-01

...). (xii) Failure to operate as a bona fide institution of learning. (xiii) Failure to employ adequate...) Failure to maintain the physical plant, curriculum, and teaching staff in the manner represented in the...

Mode of action and effects of standardized collaborative disease management on mortality and morbidity in patients with systolic heart failure: the Interdisciplinary Network for Heart Failure (INH) study.

PubMed

Angermann, Christiane E; Störk, Stefan; Gelbrich, Götz; Faller, Hermann; Jahns, Roland; Frantz, Stefan; Loeffler, Markus; Ertl, Georg

2012-01-01

Trials investigating efficacy of disease management programs (DMP) in heart failure reported contradictory results. Features rendering specific interventions successful are often ill defined. We evaluated the mode of action and effects of a nurse-coordinated DMP (HeartNetCare-HF, HNC). Patients hospitalized for systolic heart failure were randomly assigned to HNC or usual care (UC). Besides telephone-based monitoring and education, HNC addressed individual problems raised by patients, pursued networking of health care providers and provided training for caregivers. End points were time to death or rehospitalization (combined primary), heart failure symptoms, and quality of life (SF-36). Of 1007 consecutive patients, 715 were randomly assigned (HNC: n=352; UC: n=363; age, 69±12 years; 29% female; 40% New York Heart Association class III-IV). Within 180 days, 130 HNC and 137 UC patients reached the primary end point (hazard ratio, 1.02; 95% confidence interval, 0.81-1.30; P=0.89), since more HNC patients were readmitted. Overall, 32 HNC and 52 UC patients died (1 UC patient and 4 HNC patients after dropout); thus, uncensored hazard ratio was 0.62 (0.40-0.96; P=0.03). HNC patients improved more regarding New York Heart Association class (P=0.05), physical functioning (P=0.03), and physical health component (P=0.03). Except for HNC, health care utilization was comparable between groups. However, HNC patients requested counseling for noncardiac problems even more frequently than for cardiovascular or heart-failure-related issues. The primary end point of this study was neutral. However, mortality risk and surrogates of well-being improved significantly. Quantitative assessment of patient requirements suggested that besides (tele)monitoring individualized care considering also noncardiac problems should be integrated in efforts to achieve more sustainable improvement in heart failure outcomes. URL: http://www.controlled-trials.com. Unique identifier: ISRCTN23325295.

Integrated Circuit Wear out Prediction and Recycling Detection using Radio Frequency Distinct Native Attribute Features

DTIC Science & Technology

2016-12-22

105 A.1 Main Loop ... loop monitoring for preventative maintenance rather than early replacement based on statistical projections or replacement-after- failure schemes. IC...estimates, RF-DNA may provide a means to track an IC’s physical degradation during actual use. Monitoring an IC’s degradation in a closed loop fashion

A physically-based channel-modeling framework integrating HEC-RAS sediment transport capabilities and the USDA-ARS bank-stability and toe-erosion model (BSTEM)

USDA-ARS?s Scientific Manuscript database

Classical, one-dimensional, mobile bed, sediment-transport models simulate vertical channel adjustment, raising or lowering cross-section node elevations to simulate erosion or deposition. This approach does not account for bank erosion processes including toe scour and mass failure. In many systems...

A Hierarchical Approach to Fracture Mechanics

NASA Technical Reports Server (NTRS)

Saether, Erik; Taasan, Shlomo

2004-01-01

Recent research conducted under NASA LaRC's Creativity and Innovation Program has led to the development of an initial approach for a hierarchical fracture mechanics. This methodology unites failure mechanisms occurring at different length scales and provides a framework for a physics-based theory of fracture. At the nanoscale, parametric molecular dynamic simulations are used to compute the energy associated with atomic level failure mechanisms. This information is used in a mesoscale percolation model of defect coalescence to obtain statistics of fracture paths and energies through Monte Carlo simulations. The mathematical structure of predicted crack paths is described using concepts of fractal geometry. The non-integer fractal dimension relates geometric and energy measures between meso- and macroscales. For illustration, a fractal-based continuum strain energy release rate is derived for inter- and transgranular fracture in polycrystalline metals.

Hot tensile tests of Inconel 718

NASA Technical Reports Server (NTRS)

1980-01-01

The physical metallurgy of near-solidus integranular cracking in Inconel 718 welds was investigated. The data, although inconclusive, suggest at least two mechanisms which might explain intergranular cracking (microfissuring) in the heat-affected zone of several high temperature alloys. One theory is based on the separation of intergranular liquid while the other involves mechanical failure of solid ligaments surrounded by intergranular liquid. Both mechanisms concentrate strain in the grain boundaries resulting in low strain (1%) intergranular brittleness. The mechanisms reported might also pertain to the physical metallurgy of casting, powder metallurgy sintering and hot isostatic pressing.

Assessing the Value-Added by the Environmental Testing Process with the Aide of Physics/Engineering of Failure Evaluations

NASA Technical Reports Server (NTRS)

Cornford, S.; Gibbel, M.

1997-01-01

NASA's Code QT Test Effectiveness Program is funding a series of applied research activities focused on utilizing the principles of physics and engineering of failure and those of engineering economics to assess and improve the value-added by the various validation and verification activities to organizations.

SILHIL Replication of Electric Aircraft Powertrain Dynamics and Inner-Loop Control for V&V of System Health Management Routines

NASA Technical Reports Server (NTRS)

Bole, Brian; Teubert, Christopher Allen; Cuong Chi, Quach; Hogge, Edward; Vazquez, Sixto; Goebel, Kai; George, Vachtsevanos

2013-01-01

Software-in-the-loop and Hardware-in-the-loop testing of failure prognostics and decision making tools for aircraft systems will facilitate more comprehensive and cost-effective testing than what is practical to conduct with flight tests. A framework is described for the offline recreation of dynamic loads on simulated or physical aircraft powertrain components based on a real-time simulation of airframe dynamics running on a flight simulator, an inner-loop flight control policy executed by either an autopilot routine or a human pilot, and a supervisory fault management control policy. The creation of an offline framework for verifying and validating supervisory failure prognostics and decision making routines is described for the example of battery charge depletion failure scenarios onboard a prototype electric unmanned aerial vehicle.

Life Prediction Issues in Thermal/Environmental Barrier Coatings in Ceramic Matrix Composites

NASA Technical Reports Server (NTRS)

Shah, Ashwin R.; Brewer, David N.; Murthy, Pappu L. N.

2001-01-01

Issues and design requirements for the environmental barrier coating (EBC)/thermal barrier coating (TBC) life that are general and those specific to the NASA Ultra-Efficient Engine Technology (UEET) development program have been described. The current state and trend of the research, methods in vogue related to the failure analysis, and long-term behavior and life prediction of EBCITBC systems are reported. Also, the perceived failure mechanisms, variables, and related uncertainties governing the EBCITBC system life are summarized. A combined heat transfer and structural analysis approach based on the oxidation kinetics using the Arrhenius theory is proposed to develop a life prediction model for the EBC/TBC systems. Stochastic process-based reliability approach that includes the physical variables such as gas pressure, temperature, velocity, moisture content, crack density, oxygen content, etc., is suggested. Benefits of the reliability-based approach are also discussed in the report.

Does an inter-flaw length control the accuracy of rupture forecasting in geological materials?

NASA Astrophysics Data System (ADS)

Vasseur, Jérémie; Wadsworth, Fabian B.; Heap, Michael J.; Main, Ian G.; Lavallée, Yan; Dingwell, Donald B.

2017-10-01

Multi-scale failure of porous materials is an important phenomenon in nature and in material physics - from controlled laboratory tests to rockbursts, landslides, volcanic eruptions and earthquakes. A key unsolved research question is how to accurately forecast the time of system-sized catastrophic failure, based on observations of precursory events such as acoustic emissions (AE) in laboratory samples, or, on a larger scale, small earthquakes. Until now, the length scale associated with precursory events has not been well quantified, resulting in forecasting tools that are often unreliable. Here we test the hypothesis that the accuracy of the forecast failure time depends on the inter-flaw distance in the starting material. We use new experimental datasets for the deformation of porous materials to infer the critical crack length at failure from a static damage mechanics model. The style of acceleration of AE rate prior to failure, and the accuracy of forecast failure time, both depend on whether the cracks can span the inter-flaw length or not. A smooth inverse power-law acceleration of AE rate to failure, and an accurate forecast, occurs when the cracks are sufficiently long to bridge pore spaces. When this is not the case, the predicted failure time is much less accurate and failure is preceded by an exponential AE rate trend. Finally, we provide a quantitative and pragmatic correction for the systematic error in the forecast failure time, valid for structurally isotropic porous materials, which could be tested against larger-scale natural failure events, with suitable scaling for the relevant inter-flaw distances.

A review of the physics and response models for burnout of semiconductor devices

NASA Astrophysics Data System (ADS)

Orvis, W. J.; Khanaka, G. H.; Yee, J. H.

1984-12-01

Physical mechanisms that cause semiconductor devices to fail from electrical overstress--particularly, EMP-induced electrical stress--are described in light of the current literature and the authors' own research. A major concern is the cause and effects of second breakdown phenomena in p-n junction devices. Models of failure thresholds are evaluated for their inherent errors and for their ability to represent the relevant physics. Finally, the response models that relate electromagnetic stress parameters to appropriate failure-threshold parameters are discussed.

Diagnosing Recent Failures In Hodoscope Photomultiplier Tube Bases For FNAL E906

NASA Astrophysics Data System (ADS)

Stien, Haley; SeaQuest Collaboration

2017-09-01

The E906/SeaQuest experiment at Fermi National Accelerator Laboratory is researching the nucleon quark sea in order to provide an accurate determination of the quark and anti-quark distributions within the nucleon. By colliding a 120 GeV proton beam with a set of fixed targets and tracking the dimuons that hit the detectors, it is possible to study the quark/anti-quark interaction that produced the unique dimuon through the Drell-Yan process. However, E906 recently began to experience a number of failures in the Hodoscope Photomultiplier Tube bases in the first two detector stations, which are used in the trigger. It was known that the two most likely causes were radiation damage or overheating. Radiation damage was able to be ruled out when it was found that there was no increase in the number of base failures in high rate areas. It was clear that the heat generated on the custom high rate bases caused several components on the daughter cards to slowly overheat until failure. Using thermal imaging and two temperature probes, it was observed that the components on the daughter cards would reach temperatures over 100 degrees Celcius very quickly during our tests. This presentation will discuss the diagnostic process and summarize how this issue will be prevented in the future. Supported by U.S. D.O.E. Medium Energy Nuclear Physics under Grant DE-FG02-03ER41243.

Fatigue lifetime prediction of a reduced-diameter dental implant system: Numerical and experimental study.

PubMed

Duan, Yuanyuan; Gonzalez, Jorge A; Kulkarni, Pratim A; Nagy, William W; Griggs, Jason A

2018-06-16

To validate the fatigue lifetime of a reduced-diameter dental implant system predicted by three-dimensional finite element analysis (FEA) by testing physical implant specimens using an accelerated lifetime testing (ALT) strategy with the apparatus specified by ISO 14801. A commercially-available reduced-diameter titanium dental implant system (Straumann Standard Plus NN) was digitized using a micro-CT scanner. Axial slices were processed using an interactive medical image processing software (Mimics) to create 3D models. FEA analysis was performed in ABAQUS, and fatigue lifetime was predicted using fe-safe ® software. The same implant specimens (n=15) were tested at a frequency of 2Hz on load frames using apparatus specified by ISO 14801 and ALT. Multiple step-stress load profiles with various aggressiveness were used to improve testing efficiency. Fatigue lifetime statistics of physical specimens were estimated in a reliability analysis software (ALTA PRO). Fractured specimens were examined using SEM with fractographic technique to determine the failure mode. FEA predicted lifetime was within the 95% confidence interval of lifetime estimated by experimental results, which suggested that FEA prediction was accurate for this implant system. The highest probability of failure was located at the root of the implant body screw thread adjacent to the simulated bone level, which also agreed with the failure origin in physical specimens. Fatigue lifetime predictions based on finite element modeling could yield similar results in lieu of physical testing, allowing the use of virtual testing in the early stages of future research projects on implant fatigue. Copyright © 2018 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.

The SAM framework: modeling the effects of management factors on human behavior in risk analysis.

PubMed

Murphy, D M; Paté-Cornell, M E

1996-08-01

Complex engineered systems, such as nuclear reactors and chemical plants, have the potential for catastrophic failure with disastrous consequences. In recent years, human and management factors have been recognized as frequent root causes of major failures in such systems. However, classical probabilistic risk analysis (PRA) techniques do not account for the underlying causes of these errors because they focus on the physical system and do not explicitly address the link between components' performance and organizational factors. This paper describes a general approach for addressing the human and management causes of system failure, called the SAM (System-Action-Management) framework. Beginning with a quantitative risk model of the physical system, SAM expands the scope of analysis to incorporate first the decisions and actions of individuals that affect the physical system. SAM then links management factors (incentives, training, policies and procedures, selection criteria, etc.) to those decisions and actions. The focus of this paper is on four quantitative models of action that describe this last relationship. These models address the formation of intentions for action and their execution as a function of the organizational environment. Intention formation is described by three alternative models: a rational model, a bounded rationality model, and a rule-based model. The execution of intentions is then modeled separately. These four models are designed to assess the probabilities of individual actions from the perspective of management, thus reflecting the uncertainties inherent to human behavior. The SAM framework is illustrated for a hypothetical case of hazardous materials transportation. This framework can be used as a tool to increase the safety and reliability of complex technical systems by modifying the organization, rather than, or in addition to, re-designing the physical system.

Prediction of Lumen Output and Chromaticity Shift in LEDs Using Kalman Filter and Extended Kalman Filter Based Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lall, Pradeep; Wei, Junchao; Davis, J Lynn

2014-06-24

Abstract— Solid-state lighting (SSL) luminaires containing light emitting diodes (LEDs) have the potential of seeing excessive temperatures when being transported across country or being stored in non-climate controlled warehouses. They are also being used in outdoor applications in desert environments that see little or no humidity but will experience extremely high temperatures during the day. This makes it important to increase our understanding of what effects high temperature exposure for a prolonged period of time will have on the usability and survivability of these devices. Traditional light sources “burn out” at end-of-life. For an incandescent bulb, the lamp life ismore » defined by B50 life. However, the LEDs have no filament to “burn”. The LEDs continually degrade and the light output decreases eventually below useful levels causing failure. Presently, the TM-21 test standard is used to predict the L70 life of LEDs from LM-80 test data. Several failure mechanisms may be active in a LED at a single time causing lumen depreciation. The underlying TM-21 Model may not capture the failure physics in presence of multiple failure mechanisms. Correlation of lumen maintenance with underlying physics of degradation at system-level is needed. In this paper, Kalman Filter (KF) and Extended Kalman Filters (EKF) have been used to develop a 70-percent Lumen Maintenance Life Prediction Model for LEDs used in SSL luminaires. Ten-thousand hour LM-80 test data for various LEDs have been used for model development. System state at each future time has been computed based on the state space at preceding time step, system dynamics matrix, control vector, control matrix, measurement matrix, measured vector, process noise and measurement noise. The future state of the lumen depreciation has been estimated based on a second order Kalman Filter model and a Bayesian Framework. Life prediction of L70 life for the LEDs used in SSL luminaires from KF and EKF based models have been compared with the TM-21 model predictions and experimental data.« less

Management of the failed posterior/multidirectional instability patient.

PubMed

Forsythe, Brian; Ghodadra, Neil; Romeo, Anthony A; Provencher, Matthew T

2010-09-01

Although the results of operative treatment of posterior and multidirectional instability (P-MDI) of the shoulder have improved, they are not as reliable as those treated for anterior instability of the shoulder. This may be attributed to the complexities in the classification, etiology, and physical examination of a patient with suspected posterior and multidirectional instability. Failure to address the primary and concurrent lesion adequately and the development of pain and/or stiffness are contributing factors to the failure of P-MDI procedures. Other pitfalls include errors in history and physical examination, failure to recognize concomitant pathology, and problems with the surgical technique or implant failure. Patulous capsular tissues and glenoid version also play in role management of failed P-MDI patients. With an improved understanding of pertinent clinical complaints and physical examination findings and the advent of arthroscopic techniques and improved implants, successful strategies for the nonoperative and operative management of the patient after a failed posterior or multidirectional instability surgery may be elucidated. This article highlights the common presentation, physical findings, and radiographic workup in a patient that presents after a failed P-MDI repair and offers strategies for revision surgical repair.

Egg Bungee Jump!: A Pre-Engineering Activity Based on Calculation, Risk, Failure, Success--and Serendipity!

ERIC Educational Resources Information Center

Fitzgerald, Mike; Brand, Lance

2011-01-01

The separation of content between science, math, engineering, and technology education should not exist. Working with the relationship between these content areas enhances students' efforts to learn about the physical world--and the Bungee Jump offers one great way to go about it. This article describes an activity called the Egg Bungee Jump which…

A physically-based method for predicting peak discharge of floods caused by failure of natural and constructed earthen dams

USGS Publications Warehouse

Walder, J.S.

1997-01-01

We analyse a simple, physically-based model of breach formation in natural and constructed earthen dams to elucidate the principal factors controlling the flood hydrograph at the breach. Formation of the breach, which is assumed trapezoidal in cross-section, is parameterized by the mean rate of downcutting, k, the value of which is constrained by observations. A dimensionless formulation of the model leads to the prediction that the breach hydrograph depends upon lake shape, the ratio r of breach width to depth, the side slope ?? of the breach, and the parameter ?? = (V/ D3)(k/???gD), where V = lake volume, D = lake depth, and g is the acceleration due to gravity. Calculations show that peak discharge Qp depends weakly on lake shape r and ??, but strongly on ??, which is the product of a dimensionless lake volume and a dimensionless erosion rate. Qp(??) takes asymptotically distinct forms depending on whether ?? > 1. Theoretical predictions agree well with data from dam failures for which k could be reasonably estimated. The analysis provides a rapid and in many cases graphical way to estimate plausible values of Qp at the breach.

Effects of a Problem-based Structure of Physics Contents on Conceptual Learning and the Ability to Solve Problems

NASA Astrophysics Data System (ADS)

Becerra-Labra, Carlos; Gras-Martí, Albert; Martínez Torregrosa, Joaquín

2012-05-01

A model of teaching/learning is proposed based on a 'problem-based structure' of the contents of the course, in combination with a training in paper and pencil problem solving that emphasizes discussion and quantitative analysis, rather than formulae plug-in. The aim is to reverse the high failure and attrition rate among engineering undergraduates taking physics. A number of tests and questionnaires were administered to a group of students following a traditional lecture-based instruction, as well as to another group that was following an instruction scheme based on the proposed approach and the teaching materials developed ad hoc. The results show that students following the new method can develop scientific reasoning habits in problem-solving skills, and show gains in conceptual learning, attitudes and interests, and that the effects of this approach on learning are noticeable several months after the course is over.

Integrating Near-Real Time Hydrologic-Response Monitoring and Modeling for Improved Assessments of Slope Stability Along the Coastal Bluffs of the Puget Sound Rail Corridor, Washington State

NASA Astrophysics Data System (ADS)

Mirus, B. B.; Baum, R. L.; Stark, B.; Smith, J. B.; Michel, A.

2015-12-01

Previous USGS research on landslide potential in hillside areas and coastal bluffs around Puget Sound, WA, has identified rainfall thresholds and antecedent moisture conditions that correlate with heightened probability of shallow landslides. However, physically based assessments of temporal and spatial variability in landslide potential require improved quantitative characterization of the hydrologic controls on landslide initiation in heterogeneous geologic materials. Here we present preliminary steps towards integrating monitoring of hydrologic response with physically based numerical modeling to inform the development of a landslide warning system for a railway corridor along the eastern shore of Puget Sound. We instrumented two sites along the steep coastal bluffs - one active landslide and one currently stable slope with the potential for failure - to monitor rainfall, soil-moisture, and pore-pressure dynamics in near-real time. We applied a distributed model of variably saturated subsurface flow for each site, with heterogeneous hydraulic-property distributions based on our detailed site characterization of the surficial colluvium and the underlying glacial-lacustrine deposits that form the bluffs. We calibrated the model with observed volumetric water content and matric potential time series, then used simulated pore pressures from the calibrated model to calculate the suction stress and the corresponding distribution of the factor of safety against landsliding with the infinite slope approximation. Although the utility of the model is limited by uncertainty in the deeper groundwater flow system, the continuous simulation of near-surface hydrologic response can help to quantify the temporal variations in the potential for shallow slope failures at the two sites. Thus the integration of near-real time monitoring and physically based modeling contributes a useful tool towards mitigating hazards along the Puget Sound railway corridor.

Treatment of esophageal anastomotic leakage with self-expanding metal stents: analysis of risk factors for treatment failure

PubMed Central

Persson, Saga; Rouvelas, Ioannis; Kumagai, Koshi; Song, Huan; Lindblad, Mats; Lundell, Lars; Nilsson, Magnus; Tsai, Jon A.

2016-01-01

Background and study aim: The endoscopic placement of self-expandable metallic esophageal stents (SEMS) has become the preferred primary treatment for esophageal anastomotic leakage in many institutions. The aim of this study was to investigate possible risk factors for failure of SEMS-based therapy in patients with esophageal anastomotic leakage. Patients and methods: Beginning in 2003, all patients with an esophageal leak were initially approached and assessed for temporary closure with a SEMS. Until 2014, all patients at the Karolinska University Hospital with a leak from an esophagogastric or esophagojejunal anastomosis were identified. Data regarding the characteristics of the patients and leaks and the treatment outcomes were compiled. Failure of the SEMS treatment strategy was defined as death due to the leak or a major change in management strategy. The risk factors for treatment failure were analyzed with simple and multivariable logistic regression statistics. Results: A total of 447 patients with an esophagogastric or esophagojejunal anastomosis were identified. Of these patients, 80 (18 %) had an anastomotic leak, of whom 46 (58 %) received a stent as first-line treatment. In 29 of these 46 patients, the leak healed without any major change in treatment strategy. Continuous leakage after the application of a stent, decreased physical performance preoperatively, and concomitant esophagotracheal fistula were identified as independent risk factors for failure with multivariable logistic regression analysis. Conclusion: Stent treatment for esophageal anastomotic leakage is successful in the majority of cases. Continuous leakage after initial stent insertion, decreased physical performance preoperatively, and the development of an esophagotracheal fistula decrease the probability of successful treatment. PMID:27092321

Real-Time Adaptive Control Allocation Applied to a High Performance Aircraft

NASA Technical Reports Server (NTRS)

Davidson, John B.; Lallman, Frederick J.; Bundick, W. Thomas

2001-01-01

Abstract This paper presents the development and application of one approach to the control of aircraft with large numbers of control effectors. This approach, referred to as real-time adaptive control allocation, combines a nonlinear method for control allocation with actuator failure detection and isolation. The control allocator maps moment (or angular acceleration) commands into physical control effector commands as functions of individual control effectiveness and availability. The actuator failure detection and isolation algorithm is a model-based approach that uses models of the actuators to predict actuator behavior and an adaptive decision threshold to achieve acceptable false alarm/missed detection rates. This integrated approach provides control reconfiguration when an aircraft is subjected to actuator failure, thereby improving maneuverability and survivability of the degraded aircraft. This method is demonstrated on a next generation military aircraft Lockheed-Martin Innovative Control Effector) simulation that has been modified to include a novel nonlinear fluid flow control control effector based on passive porosity. Desktop and real-time piloted simulation results demonstrate the performance of this integrated adaptive control allocation approach.

Crack prediction in EB-PVD thermal barrier coatings based on the simulation of residual stresses

NASA Astrophysics Data System (ADS)

Chen, J. W.; Zhao, Y.; Liu, S.; Zhang, Z. Z.; Ma, J.

2016-07-01

Thermal barrier coatings systems (TBCs) are widely used in the field of aerospace. The durability and insulating ability of TBCs are highly dependent on the residual stresses of top coatings, thus the investigation of the residual stresses is helpful to understand the failure mechanisms of TBCs. The simulation of residual stresses evolution in electron beam physical vapor deposition (EB-PVD) TBCs is described in this work. The interface morphology of TBCs subjected to cyclic heating and cooling is observed using scanning electron microscope (SEM). An interface model of TBCs is established based on thermal elastic-plastic finite method. Residual stress distributions in TBCs are obtained to reflect the influence of interfacial roughness. Both experimental and simulation results show that it is feasible to predict the crack location by stress analysis, which is crucial to failure prediction.

Establishing Physical and Engineering Science Base to Bridge from ITER to Demo

NASA Astrophysics Data System (ADS)

Peng, Y.-K. Martin; Abdou, M.; Gates, D.; Hegna, C.; Hill, D.; Najmabadi, F.; Navratil, G.; Parker, R.

2007-11-01

A Nuclear Component Testing (NCT) Discussion Group emerged recently to clarify how ``a lowered-risk, reduced-cost approach can provide a progressive fusion environment beyond the ITER level to explore, discover, and help establish the remaining, critically needed physical and engineering sciences knowledge base for Demo.'' The group, assuming success of ITER and other contemporary projects, identified critical ``gap-filling'' investigations: plasma startup, tritium self-sufficiency, plasma facing surface performance and maintainability, first wall/blanket/divertor materials defect control and lifetime management, and remote handling. Only standard or spherical tokamak plasma conditions below the advanced regime are assumed to lower the anticipated physics risk to continuous operation (˜2 weeks). Modular designs and remote handling capabilities are included to mitigate the risk of component failure and ease replacement. Aspect ratio should be varied to lower the cost, accounting for the contending physics risks and the near-term R&D. Cost and time-effective staging from H-H, D-D, to D-T will also be considered. *Work supported by USDOE.

Investigation of failure mechanism of thermal barrier coatings (TBCs) deposited by EB-PVD technique

NASA Astrophysics Data System (ADS)

Shahid, M. R.; Abbas, Musharaf

2013-06-01

Failure mechanism of thermal barrier coatings (TBCs) prepared by electron beam physical vapor deposition (EB-PVD) technique owing to formation of micro cracks was investigated. The TBCs were deposited on the Ni-based super alloy IN-100 and the micro cracks were observed within the top ceramic coat of thermally cycled TBCs at 1050°C. It was observed that these cracks propagate in the ceramic coat in the direction normal to interface while no cracks were observed in the bond coat. SEM/EDS studies revealed that some non-uniform oxides were formed on the interface between ceramic top and metallic bond coat just below the cracks. Study proposed that the cracks were initiated due to stress owing to big difference in Pilling-Bed worth ratio of non-uniform oxides as well as thermal stress, which caused the formation of cracks in top ceramic coat leading to failure of TBCs

Parametric Studies Of Failure Mechanisms In Thermal Barrier Coatings During Thermal Cycling Using FEM

NASA Astrophysics Data System (ADS)

Srivathsa, B.; Das, D. K.

2015-12-01

Thermal barrier coatings (TBCs) are widely used on different hot components of gas turbine engines such as blades and vanes. Although, several mechanisms for the failure of the TBCs have been suggested, it is largely accepted that the durability of these coatings is primarily determined by the residual stresses that are developed during the thermal cycling. In the present study, the residual stress build-up in an electron beam physical vapour deposition (EB-PVD) based TBCs on a coupon during thermal cycling has been studied by varying three parameters such as the cooling rate, TBC thickness and substrate thickness. A two-dimensional thermomechanical generalized plane strain finite element simulations have been performed for thousand cycles. It was observed that these variations change the stress profile significantly and the stress severity factor increases non-linearly. Overall, the predictions of the model agree with reported experimental results and help in predicting the failure mechanisms.

Fool-proofing design and crisis management for customized intelligent physical fitness and healthcare system.

PubMed

Huang, Chung-Chi; Huang, Chung-Lin; Liu, Hsiao-Man

2015-01-01

In recent years, it is quite important to develop a customized system which can enhance physical fitness and health for people. And the system reliability is more important. In the paper, a fool-proofing design and crisis management for customized physical fitness and healthcare system is proposed. It is designed to prevent the failure of the various mechanisms of customized physical fitness and healthcare system, including records, surveillance, assessments, predictions, diagnosis, prescription, and scheduling. It is separated into (1) fool-proofing design module (2) crisis management module. The fool-proofing indexes are set to prevent the failure of the various mechanisms. The states of the various mechanisms are managed by the auto-checked fool-proofing indexes. If mistakes prevention was fail, we have to execute the crisis management for stopping harmful results. The crisis management will find the error level and response the solution by using fuzzy method. By the experiments, we can find the advantages of the fool-proofing design and crisis management for customized physical fitness and healthcare system. And it is effective to prevent the failure of the various mechanisms of intelligent customized physical fitness and healthcare system.

A Decentralized Compositional Framework for Dependable Decision Process in Self-Managed Cyber Physical Systems

PubMed Central

Hou, Kun-Mean; Zhang, Zhan

2017-01-01

Cyber Physical Systems (CPSs) need to interact with the changeable environment under various interferences. To provide continuous and high quality services, a self-managed CPS should automatically reconstruct itself to adapt to these changes and recover from failures. Such dynamic adaptation behavior introduces systemic challenges for CPS design, advice evaluation and decision process arrangement. In this paper, a formal compositional framework is proposed to systematically improve the dependability of the decision process. To guarantee the consistent observation of event orders for causal reasoning, this work first proposes a relative time-based method to improve the composability and compositionality of the timing property of events. Based on the relative time solution, a formal reference framework is introduced for self-managed CPSs, which includes a compositional FSM-based actor model (subsystems of CPS), actor-based advice and runtime decomposable decisions. To simplify self-management, a self-similar recursive actor interface is proposed for decision (actor) composition. We provide constraints and seven patterns for the composition of reliability and process time requirements. Further, two decentralized decision process strategies are proposed based on our framework, and we compare the reliability with the static strategy and the centralized processing strategy. The simulation results show that the one-order feedback strategy has high reliability, scalability and stability against the complexity of decision and random failure. This paper also shows a way to simplify the evaluation for dynamic system by improving the composability and compositionality of the subsystem. PMID:29120357

A Decentralized Compositional Framework for Dependable Decision Process in Self-Managed Cyber Physical Systems.

PubMed

Zhou, Peng; Zuo, Decheng; Hou, Kun-Mean; Zhang, Zhan

2017-11-09

Cyber Physical Systems (CPSs) need to interact with the changeable environment under various interferences. To provide continuous and high quality services, a self-managed CPS should automatically reconstruct itself to adapt to these changes and recover from failures. Such dynamic adaptation behavior introduces systemic challenges for CPS design, advice evaluation and decision process arrangement. In this paper, a formal compositional framework is proposed to systematically improve the dependability of the decision process. To guarantee the consistent observation of event orders for causal reasoning, this work first proposes a relative time-based method to improve the composability and compositionality of the timing property of events. Based on the relative time solution, a formal reference framework is introduced for self-managed CPSs, which includes a compositional FSM-based actor model (subsystems of CPS), actor-based advice and runtime decomposable decisions. To simplify self-management, a self-similar recursive actor interface is proposed for decision (actor) composition. We provide constraints and seven patterns for the composition of reliability and process time requirements. Further, two decentralized decision process strategies are proposed based on our framework, and we compare the reliability with the static strategy and the centralized processing strategy. The simulation results show that the one-order feedback strategy has high reliability, scalability and stability against the complexity of decision and random failure. This paper also shows a way to simplify the evaluation for dynamic system by improving the composability and compositionality of the subsystem.

Cycle life test and failure model of nickel-hydrogen cells

NASA Technical Reports Server (NTRS)

Smithrick, J. J.

1983-01-01

Six ampere hour individual pressure vessel nickel hydrogen cells were charge/discharge cycled to failure. Failure as used here is defined to occur when the end of discharge voltage degraded to 0.9 volts. They were cycled under a low earth orbit cycle regime to a deep depth of discharge (80 percent of rated ampere hour capacity). Both cell designs were fabricated by the same manufacturer and represent current state of the art. A failure model was advanced which suggests both cell designs have inadequate volume tolerance characteristics. The limited existing data base at a deep depth of discharge (DOD) was expanded. Two cells of each design were cycled. One COMSAT cell failed at cycle 1712 and the other failed at cycle 1875. For the Air Force/Hughes cells, one cell failed at cycle 2250 and the other failed at cycle 2638. All cells, of both designs, failed due to low end of discharge voltage (0.9 volts). No cell failed due to electrical shorts. After cell failure, three different reconditioning tests (deep discharge, physical reorientation, and open circuit voltage stand) were conducted on all cells of each design. A fourth reconditioning test (electrolyte addition) was conducted on one cell of each design. In addition post cycle cell teardown and failure analysis were performed on the one cell of each design which did not have electrolyte added after failure.

Solid-state lighting life prediction using extended Kalman filter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lall, Pradeep; Wei, Junchao; Davis, Lynn

2013-07-16

Solid-state lighting (SSL) luminaires containing light emitting diodes (LEDs) have the potential of seeing excessive temperatures when being transported across country or being stored in non-climate controlled warehouses. They are also being used in outdoor applications in desert environments that see little or no humidity but will experience extremely high temperatures during the day. This makes it important to increase our understanding of what effects high temperature exposure for a prolonged period of time will have on the usability and survivability of these devices. The U.S. Department of Energy has made a long term commitment to advance the efficiency, understandingmore » and development of solid-state lighting (SSL) and is making a strong push for the acceptance and use of SSL products to reduce overall energy consumption attributable to lighting. Traditional light sources “burn out” at end-of-life. For an incandescent bulb, the lamp life is defined by B50 life. However, the LEDs have no filament to “burn”. The LEDs continually degrade and the light output decreases eventually below useful levels causing failure. Presently, the TM-21 test standard is used to predict the L70 life of SSL Luminaires from LM-80 test data. The TM-21 model uses an Arrhenius Equation with an Activation Energy, Pre-decay factor and Decay Rates. Several failure mechanisms may be active in a luminaire at a single time causing lumen depreciation. The underlying TM-21 Arrhenius Model may not capture the failure physics in presence of multiple failure mechanisms. Correlation of lumen maintenance with underlying physics of degradation at system-level is needed. In this paper, a Kalman Filter and Extended Kalman Filters have been used to develop a 70% Lumen Maintenance Life Prediction Model for a LEDs used in SSL luminaires. This model can be used to calculate acceleration factors, evaluate failure-probability and identify ALT methodologies for reducing test time. Ten-thousand hour LM-80 test data for various LEDs have been used for model development. System state has been described in state space form using the measurement of the feature vector, velocity of feature vector change and the acceleration of the feature vector change. System state at each future time has been computed based on the state space at preceding time step, system dynamics matrix, control vector, control matrix, measurement matrix, measured vector, process noise and measurement noise. The future state of the lumen depreciation has been estimated based on a second order Kalman Filter model and a Bayesian Framework. The measured state variable has been related to the underlying damage using physics-based models. Life prediction of L70 life for the LEDs used in SSL luminaires from KF and EKF based models have been compared with the TM-21 model predictions and experimental data.« less

Chronicling a successful secondary implementation of Studio Physics

NASA Astrophysics Data System (ADS)

Kohl, Patrick B.; Vincent Kuo, H.

2012-09-01

The Colorado School of Mines (CSM) has taught its first-semester calculus-based introductory physics course (Physics I) using a hybrid lecture/Studio Physics format since the spring of 1997. Starting in the fall of 2007, we have been converting the second semester of our calculus-based introductory physics course (Physics II) to a hybrid lecture/Studio Physics format, beginning from a traditional lecture/lab/recitation course. In this paper, we document the stages of this transformation, highlighting what has worked and what has not, and the challenges and benefits associated with the switch to Studio Physics. A major goal in this study is to develop a method for secondary implementations of Studio physics that keeps the time and resource investments manageable. We describe the history of Studio at CSM and characterize our progress via several metrics, including pre/post Conceptual Survey of Electricity and Magnetism (CSEM) scores, Colorado Learning About Science Survey scores (CLASS), exam scores, failure rates, and a variety of qualitative observations. Results suggest that Studio has increased student performance and satisfaction despite an aggressive expansion of class sizes in the past few years. Gains have been concentrated mostly in problem-solving skills and exam performance (as opposed to conceptual survey gains), in contrast to what has sometimes been seen in other studies.

What Can We Learn from a Simple Physics-Based Earthquake Simulator?

NASA Astrophysics Data System (ADS)

Artale Harris, Pietro; Marzocchi, Warner; Melini, Daniele

2018-03-01

Physics-based earthquake simulators are becoming a popular tool to investigate on the earthquake occurrence process. So far, the development of earthquake simulators is commonly led by the approach "the more physics, the better". However, this approach may hamper the comprehension of the outcomes of the simulator; in fact, within complex models, it may be difficult to understand which physical parameters are the most relevant to the features of the seismic catalog at which we are interested. For this reason, here, we take an opposite approach and analyze the behavior of a purposely simple earthquake simulator applied to a set of California faults. The idea is that a simple simulator may be more informative than a complex one for some specific scientific objectives, because it is more understandable. Our earthquake simulator has three main components: the first one is a realistic tectonic setting, i.e., a fault data set of California; the second is the application of quantitative laws for earthquake generation on each single fault, and the last is the fault interaction modeling through the Coulomb Failure Function. The analysis of this simple simulator shows that: (1) the short-term clustering can be reproduced by a set of faults with an almost periodic behavior, which interact according to a Coulomb failure function model; (2) a long-term behavior showing supercycles of the seismic activity exists only in a markedly deterministic framework, and quickly disappears introducing a small degree of stochasticity on the recurrence of earthquakes on a fault; (3) faults that are strongly coupled in terms of Coulomb failure function model are synchronized in time only in a marked deterministic framework, and as before, such a synchronization disappears introducing a small degree of stochasticity on the recurrence of earthquakes on a fault. Overall, the results show that even in a simple and perfectly known earthquake occurrence world, introducing a small degree of stochasticity may blur most of the deterministic time features, such as long-term trend and synchronization among nearby coupled faults.

The use of light emission in failure analysis of CMOS ICs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hawkins, C.F.; Soden, J.M.; Cole, E.I. Jr.

1990-01-01

The use of photon emission for analyzing failure mechanisms and defects in CMOS ICs is presented. Techniques are given for accurate identification and spatial localization of failure mechanisms and physical defects, including defects such as short and open circuits which do not themselves emit photons.

Model-Based Anomaly Detection for a Transparent Optical Transmission System

NASA Astrophysics Data System (ADS)

Bengtsson, Thomas; Salamon, Todd; Ho, Tin Kam; White, Christopher A.

In this chapter, we present an approach for anomaly detection at the physical layer of networks where detailed knowledge about the devices and their operations is available. The approach combines physics-based process models with observational data models to characterize the uncertainties and derive the alarm decision rules. We formulate and apply three different methods based on this approach for a well-defined problem in optical network monitoring that features many typical challenges for this methodology. Specifically, we address the problem of monitoring optically transparent transmission systems that use dynamically controlled Raman amplification systems. We use models of amplifier physics together with statistical estimation to derive alarm decision rules and use these rules to automatically discriminate between measurement errors, anomalous losses, and pump failures. Our approach has led to an efficient tool for systematically detecting anomalies in the system behavior of a deployed network, where pro-active measures to address such anomalies are key to preventing unnecessary disturbances to the system's continuous operation.

39 Questionable Assumptions in Modern Physics

NASA Astrophysics Data System (ADS)

Volk, Greg

2009-03-01

The growing body of anomalies in new energy, low energy nuclear reactions, astrophysics, atomic physics, and entanglement, combined with the failure of the Standard Model and string theory to predict many of the most basic fundamental phenomena, all point to a need for major new paradigms. Not Band-Aids, but revolutionary new ways of conceptualizing physics, in the spirit of Thomas Kuhn's The Structure of Scientific Revolutions. This paper identifies a number of long-held, but unproven assumptions currently being challenged by an increasing number of alternative scientists. Two common themes, both with venerable histories, keep recurring in the many alternative theories being proposed: (1) Mach's Principle, and (2) toroidal, vortex particles. Matter-based Mach's Principle differs from both space-based universal frames and observer-based Einsteinian relativity. Toroidal particles, in addition to explaining electron spin and the fundamental constants, satisfy the basic requirement of Gauss's misunderstood B Law, that motion itself circulates. Though a comprehensive theory is beyond the scope of this paper, it will suggest alternatives to the long list of assumptions in context.

Physical mechanism and numerical simulation of the inception of the lightning upward leader

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li Qingmin; Lu Xinchang; Shi Wei

2012-12-15

The upward leader is a key physical process of the leader progression model of lightning shielding. The inception mechanism and criterion of the upward leader need further understanding and clarification. Based on leader discharge theory, this paper proposes the critical electric field intensity of the stable upward leader (CEFISUL) and characterizes it by the valve electric field intensity on the conductor surface, E{sub L}, which is the basis of a new inception criterion for the upward leader. Through numerical simulation under various physical conditions, we verified that E{sub L} is mainly related to the conductor radius, and data fitting yieldsmore » the mathematical expression of E{sub L}. We further establish a computational model for lightning shielding performance of the transmission lines based on the proposed CEFISUL criterion, which reproduces the shielding failure rate of typical UHV transmission lines. The model-based calculation results agree well with the statistical data from on-site operations, which show the effectiveness and validity of the CEFISUL criterion.« less

Physically Based Failure Criteria for Transverse Matrix Cracking

NASA Technical Reports Server (NTRS)

Davila, Carlos G.; Camanho, Pedro P.

2003-01-01

A criterion for matrix failure of laminated composite plies in transverse tension and in-plane shear is developed by examining the mechanics of transverse matrix crack growth. Matrix cracks are assumed to initiate from manufacturing defects and can propagate within planes parallel to the fiber direction and normal to the ply mid-plane. Fracture mechanics models of cracks in unidirectional laminates, embedded plies and outer plies are developed to determine the onset and direction of propagation for unstable crack growth. The models for each ply configuration relate ply thickness and ply toughness to the corresponding in-situ ply strength. Calculated results for several materials are shown to correlate well with experimental results.

High Speed Dynamics in Brittle Materials

NASA Astrophysics Data System (ADS)

Hiermaier, Stefan

2015-06-01

Brittle Materials under High Speed and Shock loading provide a continuous challenge in experimental physics, analysis and numerical modelling, and consequently for engineering design. The dependence of damage and fracture processes on material-inherent length and time scales, the influence of defects, rate-dependent material properties and inertia effects on different scales make their understanding a true multi-scale problem. In addition, it is not uncommon that materials show a transition from ductile to brittle behavior when the loading rate is increased. A particular case is spallation, a brittle tensile failure induced by the interaction of stress waves leading to a sudden change from compressive to tensile loading states that can be invoked in various materials. This contribution highlights typical phenomena occurring when brittle materials are exposed to high loading rates in applications such as blast and impact on protective structures, or meteorite impact on geological materials. A short review on experimental methods that are used for dynamic characterization of brittle materials will be given. A close interaction of experimental analysis and numerical simulation has turned out to be very helpful in analyzing experimental results. For this purpose, adequate numerical methods are required. Cohesive zone models are one possible method for the analysis of brittle failure as long as some degree of tension is present. Their recent successful application for meso-mechanical simulations of concrete in Hopkinson-type spallation tests provides new insight into the dynamic failure process. Failure under compressive loading is a particular challenge for numerical simulations as it involves crushing of material which in turn influences stress states in other parts of a structure. On a continuum scale, it can be modeled using more or less complex plasticity models combined with failure surfaces, as will be demonstrated for ceramics. Models which take microstructural cracking directly into account may provide a more physics-based approach for compressive failure in the future.

Cyber-Physical System Security of Smart Grids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dagle, Jeffery E.

2012-01-31

Abstract—This panel presentation will provide perspectives of cyber-physical system security of smart grids. As smart grid technologies are deployed, the interconnected nature of these systems is becoming more prevalent and more complex, and the cyber component of this cyber-physical system is increasing in importance. Studying system behavior in the face of failures (e.g., cyber attacks) allows a characterization of the systems’ response to failure scenarios, loss of communications, and other changes in system environment (such as the need for emergent updates and rapid reconfiguration). The impact of such failures on the availability of the system can be assessed and mitigationmore » strategies considered. Scenarios associated with confidentiality, integrity, and availability are considered. The cyber security implications associated with the American Recovery and Reinvestment Act of 2009 in the United States are discussed.« less

Association of physical activity and heart failure with preserved vs. reduced ejection fraction in the elderly: the Framingham Heart Study.

PubMed

Kraigher-Krainer, Elisabeth; Lyass, Asya; Massaro, Joseph M; Lee, Douglas S; Ho, Jennifer E; Levy, Daniel; Kannel, William B; Vasan, Ramachandran S

2013-07-01

Reduced physical activity is associated with increased risk of heart failure (HF) in middle-aged individuals. We hypothesized that physical inactivity is also associated with greater HF risk in older individuals, and examined if the association was consistent for HF with preserved ejection fraction (HFPEF) vs. HF with a reduced ejection fraction (HFREF). We evaluated 1142 elderly participants (mean age 76 years) from the Framingham Study without prior myocardial infarction and who attended a routine examination when daily physical activity was assessed systematically with a questionnaire. A composite score, the physical activity index (PAI), was calculated and modelled as tertiles, and related to incidence of HF, HFPEF, and HFREF on follow-up using proportional hazards regression models adjusting for age and sex, and then additionally for standard HF risk factors. Participants with HF and EF <45% vs. ≥45% were categorized as HFREF and HFPEF, respectively. On follow-up (mean 10 years), 250 participants developed HF (108 with HFPEF, 106 with HFREF, 36 with unavailable EF). In age- and sex-adjusted models, the middle and highest PAI tertiles were associated with a 15-56% lower risk of any HF, of HFREF, and of HFPEF, with a graded response across tertiles. In multivariable models, the association of higher PAI with lower risk of any HF and with HFPEF was maintained, whereas the association with HFREF was attenuated. Our study of an older community-based sample extends to the elderly and to HFPEF previous findings of a protective effect of physical activity on HF risk.

Detecting Slow Deformation Signals Preceding Dynamic Failure: A New Strategy For The Mitigation Of Natural Hazards (SAFER)

NASA Astrophysics Data System (ADS)

Vinciguerra, Sergio; Colombero, Chiara; Comina, Cesare; Ferrero, Anna Maria; Mandrone, Giuseppe; Umili, Gessica; Fiaschi, Andrea; Saccorotti, Gilberto

2014-05-01

Rock slope monitoring is a major aim in territorial risk assessment and mitigation. The high velocity that usually characterizes the failure phase of rock instabilities makes the traditional instruments based on slope deformation measurements not applicable for early warning systems. On the other hand the use of acoustic emission records has been often a good tool in underground mining for slope monitoring. Here we aim to identify the characteristic signs of impending failure, by deploying a "site specific" microseismic monitoring system on an unstable patch of the Madonna del Sasso landslide on the Italian Western Alps designed to monitor subtle changes of the mechanical properties of the medium and installed as close as possible to the source region. The initial characterization based on geomechanical and geophysical tests allowed to understand the instability mechanism and to design the monitoring systems to be placed. Stability analysis showed that the stability of the slope is due to rock bridges. Their failure progress can results in a global slope failure. Consequently the rock bridges potentially generating dynamic ruptures need to be monitored. A first array consisting of instruments provided by University of Turin, has been deployed on October 2013, consisting of 4 triaxial 4.5 Hz seismometers connected to a 12 channel data logger arranged in a 'large aperture' configuration which encompasses the entire unstable rock mass. Preliminary data indicate the occurrence of microseismic swarms with different spectral contents. Two additional geophones and 4 triaxial piezoelectric accelerometers able to operate at frequencies up to 23 KHz will be installed during summer 2014. This will allow us to develop a network capable of recording events with Mw < 0.5 and frequencies between 700 Hz and 20 kHz. Rock physical and mechanical characterization along with rock deformation laboratory experiments during which the evolution of related physical parameters under simulated conditions of stress and fluid content will be also studied and theoretical modelling will allow to come up with a full hazard assessment and test new methodologies for a much wider scale of applications within EU.

Probabilistic models to estimate fire-induced cable damage at nuclear power plants

NASA Astrophysics Data System (ADS)

Valbuena, Genebelin R.

Even though numerous PRAs have shown that fire can be a major contributor to nuclear power plant risk, there are some specific areas of knowledge related to this issue, such as the prediction of fire-induced damage to electrical cables and circuits, and their potential effects in the safety of the nuclear power plant, that still constitute a practical enigma, particularly for the lack of approaches/models to perform consistent and objective assessments. This report contains a discussion of three different models to estimate fire-induced cable damage likelihood given a specified fire profile: the kinetic, the heat transfer and the IR "K Factor" model. These models not only are based on statistical analysis of data available in the open literature, but to the greatest extent possible they use physics based principles to describe the underlying mechanism of failures that take place among the electrical cables upon heating due to external fires. The characterization of cable damage, and consequently the loss of functionality of electrical cables in fire is a complex phenomenon that depends on a variety of intrinsic factors such as cable materials and dimensions, and extrinsic factors such as electrical and mechanical loads on the cables, heat flux severity, and exposure time. Some of these factors are difficult to estimate even in a well-characterized fire, not only for the variability related to the unknown material composition and physical arrangements, but also for the lack of objective frameworks and theoretical models to study the behavior of polymeric wire cable insulation under dynamic external thermal insults. The results of this research will (1) help to develop a consistent framework to predict fire-induced cable failure modes likelihood, and (2) develop some guidance to evaluate and/or reduce the risk associated with these failure modes in existing and new power plant facilities. Among the models evaluated, the physics-based heat transfer model takes into account the properties and characteristics of the cables and cable materials, and the characteristics of the thermal insult. This model can be used to estimate the probability of cable damage under different thermal conditions.

The use of vision-based image quality metrics to predict low-light performance of camera phones

NASA Astrophysics Data System (ADS)

Hultgren, B.; Hertel, D.

2010-01-01

Small digital camera modules such as those in mobile phones have become ubiquitous. Their low-light performance is of utmost importance since a high percentage of images are made under low lighting conditions where image quality failure may occur due to blur, noise, and/or underexposure. These modes of image degradation are not mutually exclusive: they share common roots in the physics of the imager, the constraints of image processing, and the general trade-off situations in camera design. A comprehensive analysis of failure modes is needed in order to understand how their interactions affect overall image quality. Low-light performance is reported for DSLR, point-and-shoot, and mobile phone cameras. The measurements target blur, noise, and exposure error. Image sharpness is evaluated from three different physical measurements: static spatial frequency response, handheld motion blur, and statistical information loss due to image processing. Visual metrics for sharpness, graininess, and brightness are calculated from the physical measurements, and displayed as orthogonal image quality metrics to illustrate the relative magnitude of image quality degradation as a function of subject illumination. The impact of each of the three sharpness measurements on overall sharpness quality is displayed for different light levels. The power spectrum of the statistical information target is a good representation of natural scenes, thus providing a defined input signal for the measurement of power-spectrum based signal-to-noise ratio to characterize overall imaging performance.

Simulation-driven machine learning: Bearing fault classification

NASA Astrophysics Data System (ADS)

Sobie, Cameron; Freitas, Carina; Nicolai, Mike

2018-01-01

Increasing the accuracy of mechanical fault detection has the potential to improve system safety and economic performance by minimizing scheduled maintenance and the probability of unexpected system failure. Advances in computational performance have enabled the application of machine learning algorithms across numerous applications including condition monitoring and failure detection. Past applications of machine learning to physical failure have relied explicitly on historical data, which limits the feasibility of this approach to in-service components with extended service histories. Furthermore, recorded failure data is often only valid for the specific circumstances and components for which it was collected. This work directly addresses these challenges for roller bearings with race faults by generating training data using information gained from high resolution simulations of roller bearing dynamics, which is used to train machine learning algorithms that are then validated against four experimental datasets. Several different machine learning methodologies are compared starting from well-established statistical feature-based methods to convolutional neural networks, and a novel application of dynamic time warping (DTW) to bearing fault classification is proposed as a robust, parameter free method for race fault detection.

Data-Driven Anomaly Detection Performance for the Ares I-X Ground Diagnostic Prototype

NASA Technical Reports Server (NTRS)

Martin, Rodney A.; Schwabacher, Mark A.; Matthews, Bryan L.

2010-01-01

In this paper, we will assess the performance of a data-driven anomaly detection algorithm, the Inductive Monitoring System (IMS), which can be used to detect simulated Thrust Vector Control (TVC) system failures. However, the ability of IMS to detect these failures in a true operational setting may be related to the realistic nature of how they are simulated. As such, we will investigate both a low fidelity and high fidelity approach to simulating such failures, with the latter based upon the underlying physics. Furthermore, the ability of IMS to detect anomalies that were previously unknown and not previously simulated will be studied in earnest, as well as apparent deficiencies or misapplications that result from using the data-driven paradigm. Our conclusions indicate that robust detection performance of simulated failures using IMS is not appreciably affected by the use of a high fidelity simulation. However, we have found that the inclusion of a data-driven algorithm such as IMS into a suite of deployable health management technologies does add significant value.

Update on Simulating Ice-Cliff Failure

NASA Astrophysics Data System (ADS)

Parizek, B. R.; Christianson, K. A.; Alley, R. B.; Voytenko, D.; Vankova, I.; Dixon, T. H.; Walker, R. T.; Holland, D.

2017-12-01

Using a 2D full-Stokes diagnostic ice-flow model and engineering and glaciological failure criteria, we simulate the limiting physical conditions for rapid structural failure of subaerial ice cliffs. Previously, using a higher-order flowline model, we reported that the threshold height, in crevassed ice and/or under favorable conditions for hydrofracture or crack lubrication, may be only slightly above the 100-m maximum observed today and that under well-drained or low-melt conditions, mechanically-competent ice supports cliff heights up to 220 m (with a likely range of 180-275 m) before ultimately succumbing to tensional and compressive failure along a listric surface. However, proximal to calving fronts, bridging effects lead to variations in vertical normal stress from the background glaciostatic stress state that give rise to the along-flow gradients in vertical shear stress that are included within a full-Stokes momentum balance. When including all flowline stresses within the physics core, diagnostic solutions continue to support our earlier findings that slumping failure ultimately limits the upper bound for cliff heights. Shear failure still requires low cohesive strength, tensile failure leads to deeper dry-crevasse propagation (albeit, less than halfway through the cliff), and compressive failure drops the threshold height for triggering rapid ice-front retreat via slumping to 200 m (145-280 m).

Reduced Physical Fitness in Patients With Heart Failure as a Possible Risk Factor for Impaired Driving Performance

PubMed Central

Alosco, Michael L.; Penn, Marc S.; Spitznagel, Mary Beth; Cleveland, Mary Jo; Ott, Brian R.

2015-01-01

OBJECTIVE. Reduced physical fitness secondary to heart failure (HF) may contribute to poor driving; reduced physical fitness is a known correlate of cognitive impairment and has been associated with decreased independence in driving. No study has examined the associations among physical fitness, cognition, and driving performance in people with HF. METHOD. Eighteen people with HF completed a physical fitness assessment, a cognitive test battery, and a validated driving simulator scenario. RESULTS. Partial correlations showed that poorer physical fitness was correlated with more collisions and stop signs missed and lower scores on a composite score of attention, executive function, and psychomotor speed. Cognitive dysfunction predicted reduced driving simulation performance. CONCLUSION. Reduced physical fitness in participants with HF was associated with worse simulated driving, possibly because of cognitive dysfunction. Larger studies using on-road testing are needed to confirm our findings and identify clinical interventions to maximize safe driving. PMID:26122681

Gender-Specific Physical Symptom Biology in Heart Failure.

PubMed

Lee, Christopher S; Hiatt, Shirin O; Denfeld, Quin E; Chien, Christopher V; Mudd, James O; Gelow, Jill M

2015-01-01

There are several gender differences that may help explain the link between biology and symptoms in heart failure (HF). The aim of this study was to examine gender-specific relationships between objective measures of HF severity and physical symptoms. Detailed clinical data, including left ventricular ejection fraction and left ventricular internal end-diastolic diameter, and HF-specific physical symptoms were collected as part of a prospective cohort study. Gender interaction terms were tested in linear regression models of physical symptoms. The sample (101 women and 101 men) averaged 57 years of age and most participants (60%) had class III/IV HF. Larger left ventricle size was associated with better physical symptoms for women and worse physical symptoms for men. Decreased ventricular compliance may result in worse physical HF symptoms for women and dilation of the ventricle may be a greater progenitor of symptoms for men with HF.

Development of Motivate4Change Using the Intervention Mapping Protocol: An Interactive Technology Physical Activity and Medication Adherence Promotion Program for Hospitalized Heart Failure Patients.

PubMed

Oosterom-Calo, Rony; Te Velde, Saskia J; Stut, Wim; Brug, Johannes

2015-07-20

It is important that heart failure (HF) patients adhere to their medication regimen and engage in physical activity. Evidence shows that adherence to these HF self-management behaviors can be improved with appropriate interventions. To further promote medication adherence and physical activity among HF patients, we developed an intervention for hospitalized HF patients. The intervention mapping protocol was applied in the development of the intervention. This entailed performing a needs assessment, defining change objectives, selecting determinants and strategies, and developing the materials. The resulting intervention, Motivate4Change, makes use of interactive technology and provides HF patients with personalized feedback and advice. Specific change objectives were defined. The relevant behavioral determinants for the physical activity program were practical knowledge on physical activity performance and self-efficacy for, and perceived benefits of, physical activity. For medication-taking, the selected determinants were practical knowledge on medication-taking, perceived barriers to medication-taking, beliefs about the necessity and harm regarding the medication prescribed, and beliefs about overprescribing and harm of medication in general. The change objectives and behavior change determinants were translated in feedback and advice strategies in an interactive technology program that included tailored feedback and advice, and role models in videos in which the behaviors and overcoming barriers were demonstrated. Relevant stakeholders were involved in the interventions development process. The intervention was pretested among HF patients and adjustments were made accordingly. The interactive technology physical activity and medication adherence promotion program for hospitalized HF patients was systematically developed using the intervention mapping protocol and was based on the available theory and evidence regarding HF self-management behavior change. The intervention's efficacy is yet to be determined in evaluation research.

Problem based learning approaches to the technology education of physical therapy students.

PubMed

Castro-Sánchez, Adelaida M; Aguilar-Ferrándiz, María Encarnación M E; Matarán-Peñarrocha, Guillermo A Ga; Iglesias-Alonso, Alberto A; Fernández-Fernández, Maria Jesus M J; Moreno-Lorenzo, Carmen C

2012-01-01

Problem-Based Learning (PBL) is a whole-curriculum concept. This study aimed to compare learning preferences and strategies between physical therapy students taught by PBL and those receiving conventional lectures on massage therapy, trauma physical therapy, and electrotherapy, hydrotherapy, and thermotherapy. This quasi-experimental study included 182 male and female students on physical therapy diploma courses at three universities in Andalusia (Spain). The Canfield Learning Skills Inventory (CLSI) was used to assess learning strategies and the Approaches to Study Skills Inventory for Students (ASSIST) to analyze study preferences. At the end of the academic year 2009/10, physical therapy students taught by PBL considered the most important learning strategies to be group work, study organization, relationship of ideas, and academic results. In comparison to conventionally taught counterparts, they considered that PBL reduced lack of purpose, memorizing without relating, the law of minimum effort, and fear of failure. Among these PBL students, the most highly rated study preferences were: organization of course tasks, cordial interaction with the teacher, learning by reading and images, and direct hands-on experience. For these physical therapy students, PBL facilitates learning strategies and study preferences in comparison to conventional teaching.

Numerical Modelling of the Compressive and Tensile Response of Glass and Ceramic under High Pressure Dynamic Loading

NASA Astrophysics Data System (ADS)

Clegg, Richard A.; Hayhurst, Colin J.

1999-06-01

Ceramic materials, including glass, are commonly used as ballistic protection materials. The response of a ceramic to impact, perforation and penetration is complex and difficult and/or expensive to instrument for obtaining detailed physical data. This paper demonstrates how a hydrocode, such as AUTODYN, can be used to aid in the understanding of the response of brittle materials to high pressure impact loading and thus promote an efficient and cost effective design process. Hydrocode simulations cannot be made without appropriate characterisation of the material. Because of the complexitiy of the response of ceramic materials this often requires a number of complex material tests. Here we present a methodology for using the results of flyer plate tests, in conjunction with numerical simulations, to derive input to the Johnson-Holmquist material model for ceramics. Most of the research effort in relation to the development of hydrocode material models for ceramics has concentrated on the material behaviour under compression and shear. While the penetration process is dominated by these aspects of the material response, the final damaged state of the material can be significantly influenced by the tensile behaviour. Modelling of the final damage state is important since this is often the only physical information which is available. In this paper we present a unique implementation, in a hydrocode, for improved modelling of brittle materials in the tensile regime. Tensile failure initiation is based on any combination of principal stress or strain while the post-failure tensile response of the material is controlled through a Rankine plasticity damaging failure surface. The tensile failure surface can be combined with any of the traditional plasticity and/or compressive damage models. Finally, the models and data are applied in both traditional grid based Lagrangian and Eulerian solution techniques and the relativley new SPH (Smooth Particle Hydrodynamics) meshless technique. Simulations of long rod impacts onto ceramic faced armour and hypervelocity impacts on glass solar array space structures are presented and compared with experiments.

Debris flow initiation by runoff in a recently burned basin: Is grain-by-grain sediment bulking or en masse failure to blame?

NASA Astrophysics Data System (ADS)

McGuire, Luke A.; Rengers, Francis K.; Kean, Jason W.; Staley, Dennis M.

2017-07-01

Postwildfire debris flows are frequently triggered by runoff following high-intensity rainfall, but the physical mechanisms by which water-dominated flows transition to debris flows are poorly understood relative to debris flow initiation from shallow landslides. In this study, we combined a numerical model with high-resolution hydrologic and geomorphic data sets to test two different hypotheses for debris flow initiation during a rainfall event that produced numerous debris flows within a recently burned drainage basin. Based on simulations, large volumes of sediment eroded from the hillslopes were redeposited within the channel network throughout the storm, leading to the initiation of numerous debris flows as a result of the mass failure of sediment dams that built up within the channel. More generally, results provide a quantitative framework for assessing the potential of runoff-generated debris flows based on sediment supply and hydrologic conditions.

Debris flow initiation by runoff in a recently burned basin: Is grain-by-grain sediment bulking or en masse failure to blame?

USGS Publications Warehouse

McGuire, Luke; Rengers, Francis K.; Kean, Jason W.; Staley, Dennis M.

2017-01-01

Postwildfire debris flows are frequently triggered by runoff following high-intensity rainfall, but the physical mechanisms by which water-dominated flows transition to debris flows are poorly understood relative to debris flow initiation from shallow landslides. In this study, we combined a numerical model with high-resolution hydrologic and geomorphic data sets to test two different hypotheses for debris flow initiation during a rainfall event that produced numerous debris flows within a recently burned drainage basin. Based on simulations, large volumes of sediment eroded from the hillslopes were redeposited within the channel network throughout the storm, leading to the initiation of numerous debris flows as a result of the mass failure of sediment dams that built up within the channel. More generally, results provide a quantitative framework for assessing the potential of runoff-generated debris flows based on sediment supply and hydrologic conditions.

Influences of personality traits and continuation intentions on physical activity participation within the theory of planned behaviour.

PubMed

Chatzisarantis, Nikos L D; Hagger, Martin S

2008-01-01

Previous research has suggested that the theory of planned behaviour is insufficient in capturing all the antecedents of physical activity participation and that continuation intentions or personality traits may improve the predictive validity of the model. The present study examined the combined effects of continuation intentions and personality traits on health behaviour within the theory of planned behaviour. To examine these effects, 180 university students (N = 180, Male = 87, Female = 93, Age = 19.14 years, SD = 0.94) completed self-report measures of the theory of planned behaviour, personality traits and continuation intentions. After 5 weeks, perceived achievement of behavioural outcomes and actual participation in physical activities were assessed. Results supported discriminant validity between continuation intentions, conscientiousness and extroversion and indicated that perceived achievement of behavioural outcomes and continuation intentions of failure predicted physical activity participation after controlling for personality effects, past behaviour and other variables in the theory of planned behaviour. In addition, results indicated that conscientiousness moderated the effects of continuation intentions of failure on physical activity such that continuation intentions of failure predicted physical activity participation among conscientious and not among less conscientious individuals. These findings suggest that the effects of continuation intentions on health behaviour are contingent on personality characteristics.

Core Domains for Clinical Research in Acute Respiratory Failure Survivors: An International Modified Delphi Consensus Study.

PubMed

Turnbull, Alison E; Sepulveda, Kristin A; Dinglas, Victor D; Chessare, Caroline M; Bingham, Clifton O; Needham, Dale M

2017-06-01

To identify the "core domains" (i.e., patient outcomes, health-related conditions, or aspects of health) that relevant stakeholders agree are essential to assess in all clinical research studies evaluating the outcomes of acute respiratory failure survivors after hospital discharge. A two-round consensus process, using a modified Delphi methodology, with participants from 16 countries, including patient and caregiver representatives. Prior to voting, participants were asked to review 1) results from surveys of clinical researchers, acute respiratory failure survivors, and caregivers that rated the importance of 19 preliminary outcome domains and 2) results from a qualitative study of acute respiratory failure survivors' outcomes after hospital discharge, as related to the 19 preliminary outcome domains. Participants also were asked to suggest any additional potential domains for evaluation in the first Delphi survey. Web-based surveys of participants representing four stakeholder groups relevant to clinical research evaluating postdischarge outcomes of acute respiratory failure survivors: clinical researchers, clinicians, patients and caregivers, and U.S. federal research funding organizations. None. None. Survey response rates were 97% and 99% in round 1 and round 2, respectively. There were seven domains that met the a priori consensus criteria to be designated as core domains: physical function, cognition, mental health, survival, pulmonary function, pain, and muscle and/or nerve function. This study generated a consensus-based list of core domains that should be assessed in all clinical research studies evaluating acute respiratory failure survivors after hospital discharge. Identifying appropriate measurement instruments to assess these core domains is an important next step toward developing a set of core outcome measures for this field of research.

Problematic protocols: An overview of medical research protocols not approved by the LUMC medical ethics review committee.

PubMed

Tersmette, Derek Gideon; Engberts, Dirk Peter

2017-01-01

The Committee for Medical Ethics (CME) of Leiden University Medical Center (LUMC) was established as the first medical ethics reviewing committee (MREC) in the Netherlands. In the period 2000-2010 the CME received 2,162 protocols for review. Some of these protocols were never approved. Until now, there has existed neither an overview of these failed protocols nor an overview of the reasons for their failure. This report draws on data from the digital database, the physical archives, and the minutes of the meetings of the CME. Additional information has been obtained from the Central Committee on Research involving Human Subjects (CCRH) and survey-based research. Protocols were itemized based on characteristic features and their reviewing procedures were analyzed. In total, 1,952 out of 2,162 research protocols submitted during 2000-2010 (90.3%) were approved by the CME; 210 of 2,162 protocols (9.7%) were not approved. Of these 210 protocols, 177 failed due to reasons not related to CME reviewing. In 15 cases CME reviewing led to protocol failure, while another 10 protocols were rejected outright. Eight of the 210 submitted protocols without approval had been conducted prior to submission. In the aforementioned period, little protocol failure occurred. For the most part, protocol failure was caused by problems that are not CME related. This type of failure has several identifiable factors, none of which have anything to do with the ethical reviewing procedure by the CME. A mere 1.2% of protocols failed due to ethical review. Unacceptable burden and risks to the subject and an inadequate methodology are the most common reasons for this CME-related protocol failure.

Petascale computation of multi-physics seismic simulations

NASA Astrophysics Data System (ADS)

Gabriel, Alice-Agnes; Madden, Elizabeth H.; Ulrich, Thomas; Wollherr, Stephanie; Duru, Kenneth C.

2017-04-01

Capturing the observed complexity of earthquake sources in concurrence with seismic wave propagation simulations is an inherently multi-scale, multi-physics problem. In this presentation, we present simulations of earthquake scenarios resolving high-detail dynamic rupture evolution and high frequency ground motion. The simulations combine a multitude of representations of model complexity; such as non-linear fault friction, thermal and fluid effects, heterogeneous fault stress and fault strength initial conditions, fault curvature and roughness, on- and off-fault non-elastic failure to capture dynamic rupture behavior at the source; and seismic wave attenuation, 3D subsurface structure and bathymetry impacting seismic wave propagation. Performing such scenarios at the necessary spatio-temporal resolution requires highly optimized and massively parallel simulation tools which can efficiently exploit HPC facilities. Our up to multi-PetaFLOP simulations are performed with SeisSol (www.seissol.org), an open-source software package based on an ADER-Discontinuous Galerkin (DG) scheme solving the seismic wave equations in velocity-stress formulation in elastic, viscoelastic, and viscoplastic media with high-order accuracy in time and space. Our flux-based implementation of frictional failure remains free of spurious oscillations. Tetrahedral unstructured meshes allow for complicated model geometry. SeisSol has been optimized on all software levels, including: assembler-level DG kernels which obtain 50% peak performance on some of the largest supercomputers worldwide; an overlapping MPI-OpenMP parallelization shadowing the multiphysics computations; usage of local time stepping; parallel input and output schemes and direct interfaces to community standard data formats. All these factors enable aim to minimise the time-to-solution. The results presented highlight the fact that modern numerical methods and hardware-aware optimization for modern supercomputers are essential to further our understanding of earthquake source physics and complement both physic-based ground motion research and empirical approaches in seismic hazard analysis. Lastly, we will conclude with an outlook on future exascale ADER-DG solvers for seismological applications.

Motivational Interviewing Tailored Interventions for Heart Failure (MITI-HF): study design and methods.

PubMed

Masterson Creber, Ruth; Patey, Megan; Dickson, Victoria Vaughan; DeCesaris, Marissa; Riegel, Barbara

2015-03-01

Lack of engagement in self-care is common among patients needing to follow a complex treatment regimen, especially patients with heart failure who are affected by comorbidity, disability and side effects of poly-pharmacy. The purpose of Motivational Interviewing Tailored Interventions for Heart Failure (MITI-HF) is to test the feasibility and comparative efficacy of an MI intervention on self-care, acute heart failure physical symptoms and quality of life. We are conducting a brief, nurse-led motivational interviewing randomized controlled trial to address behavioral and motivational issues related to heart failure self-care. Participants in the intervention group receive home and phone-based motivational interviewing sessions over 90-days and those in the control group receive care as usual. Participants in both groups receive patient education materials. The primary study outcome is change in self-care maintenance from baseline to 90-days. This article presents the study design, methods, plans for statistical analysis and descriptive characteristics of the study sample for MITI-HF. Study findings will contribute to the literature on the efficacy of motivational interviewing to promote heart failure self-care. We anticipate that using an MI approach can help patients with heart failure focus on their internal motivation to change in a non-confrontational, patient-centered and collaborative way. It also affirms their ability to practice competent self-care relevant to their personal health goals. Copyright © 2015 Elsevier Inc. All rights reserved.

Railcar Roller Bearing Failure Progression Tests

DOT National Transportation Integrated Search

1982-04-01

This report describes the laboratory endurance test of six railcar roller bearings that had previously suffered physical damage or were otherwise degraded as a result of actual railroad service. Two different onboard impending bearing failure sensors...

Towards intelligent microstructural design of Nanocomposite Materials. Lightweight, high strength structural/armor materials for service in extreme environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mara, Nathan Allan; Bronkhorst, Curt Allan; Beyerlein, Irene Jane

2015-12-21

The intent of this research effort is to prove the hypothesis that: Through the employment of controlled processing parameters which are based upon integrated advanced material characterization and multi-physics material modeling, bulk nanolayered composites can be designed to contain high densities of preferred interfaces that can serve as supersinks for the defects responsible for premature damage and failure.

Protocol for Cohesionless Sample Preparation for Physical Experimentation

DTIC Science & Technology

2016-05-01

protocol for specimen preparation that will enable the use of soil strength curves based on expedient field classification testing (e.g., grain-size...void ratio and relative compaction, which compares field compaction to a laboratory maximum density. Gradation charts for the two materials used in...the failure stress. Ring shear testing was performed using the GCTS Residual-Ring Shear System SRS-150 in order to measure the peak torsional

Congenital Hydrocephalus.

PubMed

Estey, Chelsie M

2016-03-01

There are several types of hydrocephalus, which are characterized based on the location of the cerebrospinal fluid (CSF) accumulation. Physical features of animals with congenital hydrocephalus may include a dome-shaped skull, persistent fontanelle, and bilateral ventrolateral strabismus. Medical therapy involves decreasing the production of CSF. The most common surgical treatment is placement of a ventriculoperitoneal shunt. Postoperative complications may include infection, blockage, drainage abnormalities, and mechanical failure. Copyright © 2016 Elsevier Inc. All rights reserved.

Reducing the failure rate in introductory physics classes

NASA Astrophysics Data System (ADS)

Saul, Jeff; Coulombe, Patrick; Lindell, Rebecca

2017-01-01

Calculus-based introductory physics courses are often among the most difficult at many colleges and universities. With the national movement to increase STEM majors, the introductory calculus-based courses need to be less of a weed-out course and more of a course that propels students forward into successful majors. This talk discusses two approaches to reduce DFW rates and improve student retention: studio courses and parachute courses. Studio courses integrate lecture/laboratory into one course where the primary mode of instruction is small group activities. Typically, any students enrolled in the college or university can enroll in a studio version of the course. Parachute courses on the other hand, focus on the poor performing students. Designed so that students not doing well in an introductory physics course can switch into the parachute class mid-semester without harm to their GPA. In addition, the parachute course focuses on helping students build the knowledge and skills necessary for success when retaking the calculus-based Physics course. The studio course format has been found to reduce DFW rates at several universities by 40-60% compared with separate lecture and laboratory format versions of the same courses, while parachutes courses were less successful. At one university, the parachute course succeeded in helping 80% of students maintain their GPA, but only helped 20% successfully pass the calculus-based physics course.

Investigating Main and High-Speed Shaft Bearing Reliability through Uptower Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keller, Jonathan A

The most prevalent failure modes in wind turbine drivetrains are main bearing failures stemming from micropitting, white etching or axial cracks in gearbox bearings, and generator bearing failures. These failures are neither well understood nor accounted for in design standards; consequently, the mitigation strategies being developed and fielded may only partially address the physics of failure and can take years to assess. The U.S. Department of Energy continues to support research programs to investigate the influence of rolling element sliding on the formation of bearing axial cracks and main bearing micropitting.

Analysis of rockbolt performance at the Waste Isolation Pilot Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Terrill, L.J.; Francke, C.T.; Saeb, S.

Rockbolt failures at the Waste Isolation Pilot Plant have been recorded since 1990 and are categorized in terms of mode of failure. The failures are evaluated in terms of physical location of installation within the mine, local excavation geometry and stratigraphy, proximity to other excavations or shafts, and excavation age. The database of failures has revealed discrete ares of the mine containing relatively large numbers of failures. The results of metallurgical analyses and standard rockbolt load testing have generally been in agreement with the in situ evaluations.

Physics-Based Compact Model for CIGS and CdTe Solar Cells: From Voltage-Dependent Carrier Collection to Light-Enhanced Reverse Breakdown: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Xingshu; Alam, Muhammad Ashraful; Raguse, John

2015-10-15

In this paper, we develop a physics-based compact model for copper indium gallium diselenide (CIGS) and cadmium telluride (CdTe) heterojunction solar cells that attributes the failure of superposition to voltage-dependent carrier collection in the absorber layer, and interprets light-enhanced reverse breakdown as a consequence of tunneling-assisted Poole-Frenkel conduction. The temperature dependence of the model is validated against both simulation and experimental data for the entire range of bias conditions. The model can be used to characterize device parameters, optimize new designs, and most importantly, predict performance and reliability of solar panels including the effects of self-heating and reverse breakdown duemore » to partial-shading degradation.« less

From Bridges and Rockets, Lessons for Software Systems

NASA Technical Reports Server (NTRS)

Holloway, C. Michael

2004-01-01

Although differences exist between building software systems and building physical structures such as bridges and rockets, enough similarities exist that software engineers can learn lessons from failures in traditional engineering disciplines. This paper draws lessons from two well-known failures the collapse of the Tacoma Narrows Bridge in 1940 and the destruction of the space shuttle Challenger in 1986 and applies these lessons to software system development. The following specific applications are made: (1) the verification and validation of a software system should not be based on a single method, or a single style of methods; (2) the tendency to embrace the latest fad should be overcome; and (3) the introduction of software control into safety-critical systems should be done cautiously.

Fundamental Technology Development for Gas-Turbine Engine Health Management

NASA Technical Reports Server (NTRS)

Mercer, Carolyn R.; Simon, Donald L.; Hunter, Gary W.; Arnold, Steven M.; Reveley, Mary S.; Anderson, Lynn M.

2007-01-01

Integrated vehicle health management technologies promise to dramatically improve the safety of commercial aircraft by reducing system and component failures as causal and contributing factors in aircraft accidents. To realize this promise, fundamental technology development is needed to produce reliable health management components. These components include diagnostic and prognostic algorithms, physics-based and data-driven lifing and failure models, sensors, and a sensor infrastructure including wireless communications, power scavenging, and electronics. In addition, system assessment methods are needed to effectively prioritize development efforts. Development work is needed throughout the vehicle, but particular challenges are presented by the hot, rotating environment of the propulsion system. This presentation describes current work in the field of health management technologies for propulsion systems for commercial aviation.

Interamerican networks for physics education: some issues and comments

NASA Astrophysics Data System (ADS)

Halpern, Teodoro

1988-10-01

This paper provides comments about some critical and fundamental issues relevant to the creation of successful interamerican Networks for Physics Education, stressing the need for: Establishing the underlying educational goals for the proposed projects. Clear communication of these goals to interested constituencies and the public at large. Forceful image development to obtain wide-based funding. The interdependence of individuals and institutions in the networks. Closing the developed-vs.-underdeveloped schism. Sucess in this endeavour will eliminate one of the main reasons for failure of a ``cooperative'' project. This paper also provides examples of succesful interamerican Networks and some of the underlying for their successes.

Dual permeability FEM models for distributed fiber optic sensors development

NASA Astrophysics Data System (ADS)

Aguilar-López, Juan Pablo; Bogaard, Thom

2017-04-01

Fiber optic cables are commonly known for being robust and reliable mediums for transferring information at the speed of light in glass. Billions of kilometers of cable have been installed around the world for internet connection and real time information sharing. Yet, fiber optic cable is not only a mean for information transfer but also a way to sense and measure physical properties of the medium in which is installed. For dike monitoring, it has been used in the past for detecting inner core and foundation temperature changes which allow to estimate water infiltration during high water events. The DOMINO research project, aims to develop a fiber optic based dike monitoring system which allows to directly sense and measure any pore pressure change inside the dike structure. For this purpose, questions like which location, how many sensors, which measuring frequency and which accuracy are required for the sensor development. All these questions may be initially answered with a finite element model which allows to estimate the effects of pore pressure change in different locations along the cross section while having a time dependent estimation of a stability factor. The sensor aims to monitor two main failure mechanisms at the same time; The piping erosion failure mechanism and the macro-stability failure mechanism. Both mechanisms are going to be modeled and assessed in detail with a finite element based dual permeability Darcy-Richards numerical solution. In that manner, it is possible to assess different sensing configurations with different loading scenarios (e.g. High water levels, rainfall events and initial soil moisture and permeability conditions). The results obtained for the different configurations are later evaluated based on an entropy based performance evaluation. The added value of this kind of modelling approach for the sensor development is that it allows to simultaneously model the piping erosion and macro-stability failure mechanisms in a time dependent manner. In that way, the estimated pore pressures may be related to the monitored one and to both failure mechanisms. Furthermore, the approach is intended to be used in a later stage for the real time monitoring of the failure.

Report of the Odyssey FPGA Independent Assessment Team

NASA Technical Reports Server (NTRS)

Mayer, Donald C.; Katz, Richard B.; Osborn, Jon V.; Soden, Jerry M.; Barto, R.; Day, John H. (Technical Monitor)

2001-01-01

An independent assessment team (IAT) was formed and met on April 2, 2001, at Lockheed Martin in Denver, Colorado, to aid in understanding a technical issue for the Mars Odyssey spacecraft scheduled for launch on April 7, 2001. An RP1280A field-programmable gate array (FPGA) from a lot of parts common to the SIRTF, Odyssey, and Genesis missions had failed on a SIRTF printed circuit board. A second FPGA from an earlier Odyssey circuit board was also known to have failed and was also included in the analysis by the IAT. Observations indicated an abnormally high failure rate for flight RP1280A devices (the first flight lot produced using this flow) at Lockheed Martin and the causes of these failures were not determined. Standard failure analysis techniques were applied to these parts, however, additional diagnostic techniques unique for devices of this class were not used, and the parts were prematurely submitted to a destructive physical analysis, making a determination of the root cause of failure difficult. Any of several potential failure scenarios may have caused these failures, including electrostatic discharge, electrical overstress, manufacturing defects, board design errors, board manufacturing errors, FPGA design errors, or programmer errors. Several of these mechanisms would have relatively benign consequences for disposition of the parts currently installed on boards in the Odyssey spacecraft if established as the root cause of failure. However, other potential failure mechanisms could have more dire consequences. As there is no simple way to determine the likely failure mechanisms with reasonable confidence before Odyssey launch, it is not possible for the IAT to recommend a disposition for the other parts on boards in the Odyssey spacecraft based on sound engineering principles.

Psychometric properties of the Symptom Status Questionnaire-Heart Failure.

PubMed

Heo, Seongkum; Moser, Debra K; Pressler, Susan J; Dunbar, Sandra B; Mudd-Martin, Gia; Lennie, Terry A

2015-01-01

Many patients with heart failure (HF) experience physical symptoms, poor health-related quality of life (HRQOL), and high rates of hospitalization. Physical symptoms are associated with HRQOL and are major antecedents of hospitalization. However, reliable and valid physical symptom instruments have not been established. Therefore, this study examined the psychometric properties of the Symptom Status Questionnaire-Heart Failure (SSQ-HF) in patients with HF. Data on symptoms using the SSQ-HF were collected from 249 patients (aged 61 years, 67% male, 45% in New York Heart Association functional class III/IV). Internal consistency reliability was assessed using Cronbach's α. Item homogeneity was assessed using item-total and interitem correlations. Construct validity was assessed using factor analysis and testing hypotheses on known relationships. Data on depressive symptoms (Beck Depression Inventory II), HRQOL (Minnesota Living With Heart Failure Questionnaire), and event-free survival were collected to test known relationships. Internal consistency reliability was supported: Cronbach's α was .80. Item-total correlation coefficients and interitem correlation coefficients were acceptable. Factor analysis supported the construct validity of the instrument. More severe symptoms were associated with more depressive symptoms, poorer HRQOL, and more risk for hospitalization, emergency department visit, or death, controlling for covariates. The findings of this study support the reliability and validity of the SSQ-HF. Clinicians and researchers can use this instrument to assess physical symptoms in patients with HF.

[Sport for pacemaker patients].

PubMed

Israel, C W

2012-06-01

Sport activity is an important issue in many patients with a pacemaker either because they performed sport activities before pacemaker implantation to reduce the cardiovascular risk or to improve the course of an underlying cardiovascular disease (e.g. coronary artery disease, heart failure) by sports. Compared to patients with an implantable cardioverter defibrillator (ICD) the risks from underlying cardiovascular disease (e.g. ischemia, heart failure), arrhythmia, lead dysfunction or inappropriate therapy are less important or absent. Sport is contraindicated in dyspnea at rest, acute heart failure, new complex arrhythmia, acute myocarditis and acute myocardial infarction, valvular disease with indications for intervention and surgery and comorbidities which prevent physical activity. Patients with underlying cardiovascular disease (including hypertension) should preferably perform types and levels of physical activity that are aerobic (with dynamic exercise) such as running, swimming, cycling instead of sport with high anaerobic demands and high muscular workload. In heart failure, studies demonstrated advantages of isometric sport that increases the amount of muscle, thereby preventing cardiac cachexia. Sport with a risk of blows to the chest or physical contact (e.g. boxing, rugby, martial arts) should be avoided. Implantation, programming and follow-up should respect specific precautions to allow optimal physical activity with a pacemaker including implantation of bipolar leads on the side contralateral to the dominant hand, individual programming of the upper sensor and tracking rate and regular exercise testing.

Complex Failure Forewarning System - DHS Conference Proceedings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abercrombie, Robert K; Hively, Lee M; Prowell, Stacy J

2011-01-01

As the critical infrastructures of the United States have become more and more dependent on public and private networks, the potential for widespread national impact resulting from disruption or failure of these networks has also increased. Securing the nation s critical infrastructures requires protecting not only their physical systems but, just as important, the cyber portions of the systems on which they rely. A failure is inclusive of random events, design flaws, and instabilities caused by cyber (and/or physical) attack. One such domain, aging bridges, is used to explain the Complex Structure Failure Forewarning System. We discuss the workings ofmore » such a system in the context of the necessary sensors, command and control and data collection as well as the cyber security efforts that would support this system. Their application and the implications of this computing architecture are also discussed, with respect to our nation s aging infrastructure.« less

Forewarning of Failure in Complex Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abercrombie, Robert K; Hively, Lee M; Prowell, Stacy J

2011-01-01

As the critical infrastructures of the United States have become more and more dependent on public and private networks, the potential for widespread national impact resulting from disruption or failure of these networks has also increased. Securing the nation s critical infrastructures requires protecting not only their physical systems but, just as important, the cyber portions of the systems on which they rely. A failure is inclusive of random events, design flaws, and instabilities caused by cyber (and/or physical) attack. One such domain is failure in critical equipment. A second is aging bridges. We discuss the workings of such amore » system in the context of the necessary sensors, command and control and data collection as well as the cyber security efforts that would support this system. Their application and the implications of this computing architecture are also discussed, with respect to our nation s aging infrastructure.« less

Efficient Actor Recovery Paradigm for Wireless Sensor and Actor Networks

PubMed Central

Mahjoub, Reem K.; Elleithy, Khaled

2017-01-01

The actor nodes are the spine of wireless sensor and actor networks (WSANs) that collaborate to perform a specific task in an unverified and uneven environment. Thus, there is a possibility of high failure rate in such unfriendly scenarios due to several factors such as power consumption of devices, electronic circuit failure, software errors in nodes or physical impairment of the actor nodes and inter-actor connectivity problem. Therefore, it is extremely important to discover the failure of a cut-vertex actor and network-disjoint in order to improve the Quality-of-Service (QoS). In this paper, we propose an Efficient Actor Recovery (EAR) paradigm to guarantee the contention-free traffic-forwarding capacity. The EAR paradigm consists of a Node Monitoring and Critical Node Detection (NMCND) algorithm that monitors the activities of the nodes to determine the critical node. In addition, it replaces the critical node with backup node prior to complete node-failure which helps balancing the network performance. The packets are handled using Network Integration and Message Forwarding (NIMF) algorithm that determines the source of forwarding the packets; either from actor or sensor. This decision-making capability of the algorithm controls the packet forwarding rate to maintain the network for a longer time. Furthermore, for handling the proper routing strategy, Priority-Based Routing for Node Failure Avoidance (PRNFA) algorithm is deployed to decide the priority of the packets to be forwarded based on the significance of information available in the packet. To validate the effectiveness of the proposed EAR paradigm, the proposed algorithms were tested using OMNET++ simulation. PMID:28420102

Efficient Actor Recovery Paradigm for Wireless Sensor and Actor Networks.

PubMed

Mahjoub, Reem K; Elleithy, Khaled

2017-04-14

The actor nodes are the spine of wireless sensor and actor networks (WSANs) that collaborate to perform a specific task in an unverified and uneven environment. Thus, there is a possibility of high failure rate in such unfriendly scenarios due to several factors such as power consumption of devices, electronic circuit failure, software errors in nodes or physical impairment of the actor nodes and inter-actor connectivity problem. Therefore, it is extremely important to discover the failure of a cut-vertex actor and network-disjoint in order to improve the Quality-of-Service (QoS). In this paper, we propose an Efficient Actor Recovery (EAR) paradigm to guarantee the contention-free traffic-forwarding capacity. The EAR paradigm consists of a Node Monitoring and Critical Node Detection (NMCND) algorithm that monitors the activities of the nodes to determine the critical node. In addition, it replaces the critical node with backup node prior to complete node-failure which helps balancing the network performance. The packets are handled using Network Integration and Message Forwarding (NIMF) algorithm that determines the source of forwarding the packets; either from actor or sensor. This decision-making capability of the algorithm controls the packet forwarding rate to maintain the network for a longer time. Furthermore, for handling the proper routing strategy, Priority-Based Routing for Node Failure Avoidance (PRNFA) algorithm is deployed to decide the priority of the packets to be forwarded based on the significance of information available in the packet. To validate the effectiveness of the proposed EAR paradigm, the proposed algorithms were tested using OMNET++ simulation.

Damage assessment in multilayered MEMS structures under thermal fatigue

NASA Astrophysics Data System (ADS)

Maligno, A. R.; Whalley, D. C.; Silberschmidt, V. V.

2011-07-01

This paper reports on the application of a Physics of Failure (PoF) methodology to assessing the reliability of a micro electro mechanical system (MEMS). Numerical simulations, based on the finite element method (FEM) using a sub-domain approach was used to examine the damage onset due to temperature variations (e.g. yielding of metals which may lead to thermal fatigue). In this work remeshing techniques were employed in order to develop a damage tolerance approach based on the assumption that initial flaws exist in the multi-layered.

Overview of the SHIELDS Project at LANL

NASA Astrophysics Data System (ADS)

Jordanova, V.; Delzanno, G. L.; Henderson, M. G.; Godinez, H. C.; Jeffery, C. A.; Lawrence, E. C.; Meierbachtol, C.; Moulton, D.; Vernon, L.; Woodroffe, J. R.; Toth, G.; Welling, D. T.; Yu, Y.; Birn, J.; Thomsen, M. F.; Borovsky, J.; Denton, M.; Albert, J.; Horne, R. B.; Lemon, C. L.; Markidis, S.; Young, S. L.

2015-12-01

The near-Earth space environment is a highly dynamic and coupled system through a complex set of physical processes over a large range of scales, which responds nonlinearly to driving by the time-varying solar wind. Predicting variations in this environment that can affect technologies in space and on Earth, i.e. "space weather", remains a big space physics challenge. We present a recently funded project through the Los Alamos National Laboratory (LANL) Directed Research and Development (LDRD) program that is developing a new capability to understand, model, and predict Space Hazards Induced near Earth by Large Dynamic Storms, the SHIELDS framework. The project goals are to specify the dynamics of the hot (keV) particles (the seed population for the radiation belts) on both macro- and micro-scale, including important physics of rapid particle injection and acceleration associated with magnetospheric storms/substorms and plasma waves. This challenging problem is addressed using a team of world-class experts in the fields of space science and computational plasma physics and state-of-the-art models and computational facilities. New data assimilation techniques employing data from LANL instruments on the Van Allen Probes and geosynchronous satellites are developed in addition to physics-based models. This research will provide a framework for understanding of key radiation belt drivers that may accelerate particles to relativistic energies and lead to spacecraft damage and failure. The ability to reliably distinguish between various modes of failure is critically important in anomaly resolution and forensics. SHIELDS will enhance our capability to accurately specify and predict the near-Earth space environment where operational satellites reside.

Failure modes and effects analysis (FMEA) for Gamma Knife radiosurgery.

PubMed

Xu, Andy Yuanguang; Bhatnagar, Jagdish; Bednarz, Greg; Flickinger, John; Arai, Yoshio; Vacsulka, Jonet; Feng, Wenzheng; Monaco, Edward; Niranjan, Ajay; Lunsford, L Dade; Huq, M Saiful

2017-11-01

Gamma Knife radiosurgery is a highly precise and accurate treatment technique for treating brain diseases with low risk of serious error that nevertheless could potentially be reduced. We applied the AAPM Task Group 100 recommended failure modes and effects analysis (FMEA) tool to develop a risk-based quality management program for Gamma Knife radiosurgery. A team consisting of medical physicists, radiation oncologists, neurosurgeons, radiation safety officers, nurses, operating room technologists, and schedulers at our institution and an external physicist expert on Gamma Knife was formed for the FMEA study. A process tree and a failure mode table were created for the Gamma Knife radiosurgery procedures using the Leksell Gamma Knife Perfexion and 4C units. Three scores for the probability of occurrence (O), the severity (S), and the probability of no detection for failure mode (D) were assigned to each failure mode by 8 professionals on a scale from 1 to 10. An overall risk priority number (RPN) for each failure mode was then calculated from the averaged O, S, and D scores. The coefficient of variation for each O, S, or D score was also calculated. The failure modes identified were prioritized in terms of both the RPN scores and the severity scores. The established process tree for Gamma Knife radiosurgery consists of 10 subprocesses and 53 steps, including a subprocess for frame placement and 11 steps that are directly related to the frame-based nature of the Gamma Knife radiosurgery. Out of the 86 failure modes identified, 40 Gamma Knife specific failure modes were caused by the potential for inappropriate use of the radiosurgery head frame, the imaging fiducial boxes, the Gamma Knife helmets and plugs, the skull definition tools as well as other features of the GammaPlan treatment planning system. The other 46 failure modes are associated with the registration, imaging, image transfer, contouring processes that are common for all external beam radiation therapy techniques. The failure modes with the highest hazard scores are related to imperfect frame adaptor attachment, bad fiducial box assembly, unsecured plugs/inserts, overlooked target areas, and undetected machine mechanical failure during the morning QA process. The implementation of the FMEA approach for Gamma Knife radiosurgery enabled deeper understanding of the overall process among all professionals involved in the care of the patient and helped identify potential weaknesses in the overall process. The results of the present study give us a basis for the development of a risk based quality management program for Gamma Knife radiosurgery. © 2017 The Authors. Journal of Applied Clinical Medical Physics published by Wiley Periodicals, Inc. on behalf of American Association of Physicists in Medicine.

SHIELDS Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jordanova, Vania Koleva

Predicting variations in the near-Earth space environment that can lead to spacecraft damage and failure, i.e. “space weather”, remains a big space physics challenge. A new capability was developed at Los Alamos National Laboratory (LANL) to understand, model, and predict Space Hazards Induced near Earth by Large Dynamic Storms, the SHIELDS framework. This framework simulates the dynamics of the Surface Charging Environment (SCE), the hot (keV) electrons representing the source and seed populations for the radiation belts, on both macro- and micro-scale. In addition to using physics-based models (like RAM-SCB, BATS-R-US, and iPIC3D), new data assimilation techniques employing data frommore » LANL instruments on the Van Allen Probes and geosynchronous satellites were developed. An order of magnitude improvement in the accuracy in the simulation of the spacecraft surface charging environment was thus obtained. SHIELDS also includes a post-processing tool designed to calculate the surface charging for specific spacecraft geometry using the Curvilinear Particle-In-Cell (CPIC) code and to evaluate anomalies' relation to SCE dynamics. Such diagnostics is critically important when performing forensic analyses of space-system failures.« less

Cabin Environment Physics Risk Model

NASA Technical Reports Server (NTRS)

Mattenberger, Christopher J.; Mathias, Donovan Leigh

2014-01-01

This paper presents a Cabin Environment Physics Risk (CEPR) model that predicts the time for an initial failure of Environmental Control and Life Support System (ECLSS) functionality to propagate into a hazardous environment and trigger a loss-of-crew (LOC) event. This physics-of failure model allows a probabilistic risk assessment of a crewed spacecraft to account for the cabin environment, which can serve as a buffer to protect the crew during an abort from orbit and ultimately enable a safe return. The results of the CEPR model replace the assumption that failure of the crew critical ECLSS functionality causes LOC instantly, and provide a more accurate representation of the spacecraft's risk posture. The instant-LOC assumption is shown to be excessively conservative and, moreover, can impact the relative risk drivers identified for the spacecraft. This, in turn, could lead the design team to allocate mass for equipment to reduce overly conservative risk estimates in a suboptimal configuration, which inherently increases the overall risk to the crew. For example, available mass could be poorly used to add redundant ECLSS components that have a negligible benefit but appear to make the vehicle safer due to poor assumptions about the propagation time of ECLSS failures.

Voluntary running exercise prevents β-cell failure in susceptible islets of the Zucker diabetic fatty rat.

PubMed

Delghingaro-Augusto, Viviane; Décary, Simon; Peyot, Marie-Line; Latour, Martin G; Lamontagne, Julien; Paradis-Isler, Nicolas; Lacharité-Lemieux, Marianne; Akakpo, Huguette; Birot, Olivier; Nolan, Christopher J; Prentki, Marc; Bergeron, Raynald

2012-01-15

Physical activity improves glycemic control in type 2 diabetes (T2D), but its contribution to preserving β-cell function is uncertain. We evaluated the role of physical activity on β-cell secretory function and glycerolipid/fatty acid (GL/FA) cycling in male Zucker diabetic fatty (ZDF) rats. Six-week-old ZDF rats engaged in voluntary running for 6 wk (ZDF-A). Inactive Zucker lean and ZDF (ZDF-I) rats served as controls. ZDF-I rats displayed progressive hyperglycemia with β-cell failure evidenced by falling insulinemia and reduced insulin secretion to oral glucose. Isolated ZDF-I rat islets showed reduced glucose-stimulated insulin secretion expressed per islet and per islet protein. They were also characterized by loss of the glucose regulation of fatty acid oxidation and GL/FA cycling, reduced mRNA expression of key β-cell genes, and severe reduction of insulin stores. Physical activity prevented diabetes in ZDF rats through sustaining β-cell compensation to insulin resistance shown in vivo and in vitro. Surprisingly, ZDF-A islets had persistent defects in fatty acid oxidation, GL/FA cycling, and β-cell gene expression. ZDF-A islets, however, had preserved islet insulin mRNA and insulin stores compared with ZDF-I rats. Physical activity did not prevent hyperphagia, dyslipidemia, or obesity in ZDF rats. In conclusion, islets of ZDF rats have a susceptibility to failure that is possibly due to altered β-cell fatty acid metabolism. Depletion of pancreatic islet insulin stores is a major contributor to islet failure in this T2D model, preventable by physical activity.

[Analysis of quality of life using the generic SF-36 questionnaire in patients with heart failure].

PubMed

López Castro, J; Cid Conde, L; Fernández Rodríguez, V; Failde Garrido, J M; Almazán Ortega, R

2013-01-01

Heart failure is one of the major chronic diseases that affect health related quality of life. The objective of this study was to evaluate the quality of life in patients with New York Heart Association functional class I-III using the SF-36 on a cohort of survivors of the EPICOUR Study Group and compare the quality of life with the general Spanish population of the same sex and age group. A cohort study, observational, and prospective study was conducted on survivors of the EPICOUR Study Group, on whom a clinical-progression-outcome review was performed along with the SF-36. The quality of life was studied in 50 patients (60% male). The average age of men was 64.8 years and women 68.3. When analyzing the SF-36, it was observed that the results were lower in the physical dimensions than in the mental dimensions. The quality of life worsened with increasing functional class (statistically significant differences for scales of physical functioning, social functioning and borderline significance in mental health scale). When comparing patients with the general population of the same age and sex, patients with heart failure showed lower scores on all scales (significant differences in physical functioning, body pain, vitality, and social role for men, and physical function and emotional role for women). Heart failure causes a negative impact on quality of life, physical functioning, as well as psychosocial function, with the impairment becoming worse with increased functional class. Copyright © 2013 SECA. Published by Elsevier Espana. All rights reserved.

Operative shortening of the sling as a second-line treatment after TVT failure

PubMed Central

Matuszewski, Marcin; Michajłowski, Jerzy; Krajka, Kazimierz

2011-01-01

Introduction Stress urinary incontinence (SUI) is defined as an involuntary loss of urine during physical exertion, sneezing, coughing, laughing, or other activities that put pressure on the bladder. In some cases, recurrent or persistent SUI after sling operations may be caused by too loose placement of the sling. In the current study, we describe our method of shortening of the sling as a second-line treatment of tension-free vaginal tape (TVT) failure. Materials and methods Four women, aged 46-61, after initial TVT operation were treated for persistent SUI. The severity of SUI was estimated by: physical examinations, cough tests, 24-h pad tests, and King's Health Questionnaire. The shortening procedure, based on excising the fragment of tape and suturing it back, was performed in all patients. Results All cases achieved a good result, which was defined as restoration of full continence. No complications occurred. The 12-month follow-up showed no side-effects. The postoperative control tests: the cough and 24-h pad tests were negative in all women. The general health perceptions increased after the shortening procedure by a mean value 44.25%. The incontinence impact decreased by a mean value 44.6%. In all patients, role and physical limitations significantly decreased (by 88.5% and 80.5%, respectively). The negative emotions connected with SUI significantly decreased after the second procedure. Conclusions The operative shortening of the implanted sling is a simple, cheap, and effective method of second-line treatment in cases of TVT failure and may be offered to the majority of patients with insufficient urethral support after the first procedure. PMID:24578885

REVIEWS OF TOPICAL PROBLEMS: 21st century: what is life from the perspective of physics?

NASA Astrophysics Data System (ADS)

Ivanitskii, Genrikh R.

2010-07-01

The evolution of the biophysical paradigm over 65 years since the publication in 1944 of Erwin Schrödinger's What is Life? The Physical Aspects of the Living Cell is reviewed. Based on the advances in molecular genetics, it is argued that all the features characteristic of living systems can also be found in nonliving ones. Ten paradoxes in logic and physics are analyzed that allow defining life in terms of a spatial-temporal hierarchy of structures and combinatory probabilistic logic. From the perspective of physics, life can be defined as resulting from a game involving interactions of matter one part of which acquires the ability to remember the success (or failure) probabilities from the previous rounds of the game, thereby increasing its chances for further survival in the next round. This part of matter is currently called living matter.

Physically based DC lifetime model for lead zirconate titanate films

NASA Astrophysics Data System (ADS)

Garten, Lauren M.; Hagiwara, Manabu; Ko, Song Won; Trolier-McKinstry, Susan

2017-09-01

Accurate lifetime predictions for Pb(Zr0.52Ti0.48)O3 thin films are critical for a number of applications, but current reliability models are not consistent with the resistance degradation mechanisms in lead zirconate titanate. In this work, the reliability and lifetime of chemical solution deposited (CSD) and sputtered Pb(Zr0.52Ti0.48)O3 thin films are characterized using highly accelerated lifetime testing (HALT) and leakage current-voltage (I-V) measurements. Temperature dependent HALT results and impedance spectroscopy show activation energies of approximately 1.2 eV for the CSD films and 0.6 eV for the sputtered films. The voltage dependent HALT results are consistent with previous reports, but do not clearly indicate what causes device failure. To understand more about the underlying physical mechanisms leading to degradation, the I-V data are fit to known conduction mechanisms, with Schottky emission having the best-fit and realistic extracted material parameters. Using the Schottky emission equation as a base, a unique model is developed to predict the lifetime under highly accelerated testing conditions based on the physical mechanisms of degradation.

Extreme Threshold Failures Within a Heterogeneous Elastic Thin Sheet and the Spatial-Temporal Development of Induced Seismicity Within the Groningen Gas Field

NASA Astrophysics Data System (ADS)

Bourne, S. J.; Oates, S. J.

2017-12-01

Measurements of the strains and earthquakes induced by fluid extraction from a subsurface reservoir reveal a transient, exponential-like increase in seismicity relative to the volume of fluids extracted. If the frictional strength of these reactivating faults is heterogeneously and randomly distributed, then progressive failures of the weakest fault patches account in a general manner for this initial exponential-like trend. Allowing for the observable elastic and geometric heterogeneity of the reservoir, the spatiotemporal evolution of induced seismicity over 5 years is predictable without significant bias using a statistical physics model of poroelastic reservoir deformations inducing extreme threshold frictional failures of previously inactive faults. This model is used to forecast the temporal and spatial probability density of earthquakes within the Groningen natural gas reservoir, conditional on future gas production plans. Probabilistic seismic hazard and risk assessments based on these forecasts inform the current gas production policy and building strengthening plans.

Systems Reliability Framework for Surface Water Sustainability and Risk Management

NASA Astrophysics Data System (ADS)

Myers, J. R.; Yeghiazarian, L.

2016-12-01

With microbial contamination posing a serious threat to the availability of clean water across the world, it is necessary to develop a framework that evaluates the safety and sustainability of water systems in respect to non-point source fecal microbial contamination. The concept of water safety is closely related to the concept of failure in reliability theory. In water quality problems, the event of failure can be defined as the concentration of microbial contamination exceeding a certain standard for usability of water. It is pertinent in watershed management to know the likelihood of such an event of failure occurring at a particular point in space and time. Microbial fate and transport are driven by environmental processes taking place in complex, multi-component, interdependent environmental systems that are dynamic and spatially heterogeneous, which means these processes and therefore their influences upon microbial transport must be considered stochastic and variable through space and time. A physics-based stochastic model of microbial dynamics is presented that propagates uncertainty using a unique sampling method based on artificial neural networks to produce a correlation between watershed characteristics and spatial-temporal probabilistic patterns of microbial contamination. These results are used to address the question of water safety through several sustainability metrics: reliability, vulnerability, resilience and a composite sustainability index. System reliability is described uniquely though the temporal evolution of risk along watershed points or pathways. Probabilistic resilience describes how long the system is above a certain probability of failure, and the vulnerability metric describes how the temporal evolution of risk changes throughout a hierarchy of failure levels. Additionally our approach allows for the identification of contributions in microbial contamination and uncertainty from specific pathways and sources. We expect that this framework will significantly improve the efficiency and precision of sustainable watershed management strategies through providing a better understanding of how watershed characteristics and environmental parameters affect surface water quality and sustainability. With microbial contamination posing a serious threat to the availability of clean water across the world, it is necessary to develop a framework that evaluates the safety and sustainability of water systems in respect to non-point source fecal microbial contamination. The concept of water safety is closely related to the concept of failure in reliability theory. In water quality problems, the event of failure can be defined as the concentration of microbial contamination exceeding a certain standard for usability of water. It is pertinent in watershed management to know the likelihood of such an event of failure occurring at a particular point in space and time. Microbial fate and transport are driven by environmental processes taking place in complex, multi-component, interdependent environmental systems that are dynamic and spatially heterogeneous, which means these processes and therefore their influences upon microbial transport must be considered stochastic and variable through space and time. A physics-based stochastic model of microbial dynamics is presented that propagates uncertainty using a unique sampling method based on artificial neural networks to produce a correlation between watershed characteristics and spatial-temporal probabilistic patterns of microbial contamination. These results are used to address the question of water safety through several sustainability metrics: reliability, vulnerability, resilience and a composite sustainability index. System reliability is described uniquely though the temporal evolution of risk along watershed points or pathways. Probabilistic resilience describes how long the system is above a certain probability of failure, and the vulnerability metric describes how the temporal evolution of risk changes throughout a hierarchy of failure levels. Additionally our approach allows for the identification of contributions in microbial contamination and uncertainty from specific pathways and sources. We expect that this framework will significantly improve the efficiency and precision of sustainable watershed management strategies through providing a better understanding of how watershed characteristics and environmental parameters affect surface water quality and sustainability.

Role and Value of Clinical Pharmacy in Heart Failure Management.

PubMed

Stough, W G; Patterson, J H

2017-08-01

Effectively managing heart failure requires a multidisciplinary, holistic approach attuned to many factors: diagnosis of structural and functional cardiac abnormalities; medication, device, or surgical management; concomitant treatment of comorbidities; physical rehabilitation; dietary considerations; and social factors. This practice paper highlights the pharmacist's role in the management of patients with heart failure, the evidence supporting their functions, and steps to ensure the pharmacist resource is available to the broad population of patients with heart failure. © 2017 American Society for Clinical Pharmacology and Therapeutics.

Sustaining the Progress to Improve Physics Education

ERIC Educational Resources Information Center

Abdul-Razzaq, Wathiq

2010-01-01

One of the problems we face in teaching introductory physics courses at the college level is that about 2/3 of students never had physics prior coming to college. Thus, many students find it very difficult to learn physics for the first time at the relatively fast-paced teaching of college physics courses. Sometimes the drop/failure/withdrawal…

Using Reputation Based Trust to Overcome Malfunctions and Malicious Failures in Electric Power Protection Systems

DTIC Science & Technology

2011-09-01

concert with a physical attack. Additionally, the importance of preventive measures implemented by a social human network to counteract a cyber attack...integrity of the data stored on specific computers. This coordinated cyber attack would have been successful if not for the trusted social network...established by Mr. Hillar Aarelaid, head of the Estonian computer 6 emergency response team (CERT). This social network consisted of Mr. Hillar Aarelaid

Field failure mechanisms for photovoltaic modules

NASA Technical Reports Server (NTRS)

Dumas, L. N.; Shumka, A.

1981-01-01

Beginning in 1976, Department of Energy field centers have installed and monitored a number of field tests and application experiments using current state-of-the-art photovoltaic modules. On-site observations of module physical and electrical degradation, together with in-depth laboratory analysis of failed modules, permits an overall assessment of the nature and causes of early field failures. Data on failure rates are presented, and key failure mechanisms are analyzed with respect to origin, effect, and prospects for correction. It is concluded that all failure modes identified to date are avoidable or controllable through sound design and production practices.

A systematic review on reminder systems in physical therapy

PubMed Central

Jangi, Majid; Ferandez-de-las-Penas, Cesar; Tara, Mahmoud; Moghbeli, Fateme; Ghaderi, Fariba; Javanshir, Khodabakhsh

2018-01-01

Background: The main goal of physical therapy is to help the patient gain a better health status. Several studies have investigated the use of reminders to prevent such failures on the patients’ side. This article presents a systematic review of the literature concerning reminders in physical therapy. Methods: Databases were searched until May 2017 and literatures were found from April 1992 until 2017. The literature recruitment strategy was based on applying several keywords and Medical Subject Heading (MeSH) combination running against title and abstract, including concepts such as reminder, physical therapy. The finally selected articles were categorized through reminder aspects such as how, who feedback. Data were extracted according to PRISMA guidelines. Results: In 47% of studies, the reminder was sent to the patients, 29% to the physical therapists and 12% to the caretaker team. In 24% of the studies, paper-based letters were main medium for reminders while the rest were various types of media like emails and SMS mobile text messages. 35% of the articles showed positive effects of the reminders. Conclusions: Many reminder methods consisted of SMS, phone calls, letters, emails and notices on the wall were used in physical therapy. Reminders may be used to improve patients' adherence to exercise programs. PMID:29387313

Autograft versus nonirradiated allograft tissue for anterior cruciate ligament reconstruction: a systematic review.

PubMed

Mariscalco, Michael W; Magnussen, Robert A; Mehta, Divyesh; Hewett, Timothy E; Flanigan, David C; Kaeding, Christopher C

2014-02-01

An autograft has traditionally been the gold standard for anterior cruciate ligament reconstruction (ACLR), but the use of allograft tissue has increased in recent years. While numerous studies have demonstrated that irradiated allografts are associated with increased failure rates, some report excellent results after ACLR with nonirradiated allografts. The purpose of this systematic review was to determine whether the use of nonirradiated allograft tissue is associated with poorer outcomes when compared with autografts. Patients undergoing ACLR with autografts versus nonirradiated allografts will demonstrate no significant differences in graft failure risk, laxity on postoperative physical examination, or differences in patient-oriented outcome scores. Systematic review. A systematic review was performed to identify prospective or retrospective comparative studies (evidence level 1, 2, or 3) of autografts versus nonirradiated allografts for ACLR. Outcome data included graft failure based on clinical findings and instrumented laxity, postoperative laxity on physical examination, and patient-reported outcome scores. Studies were excluded if they did not specify whether the allograft had been irradiated. Quality assessment and data extraction were performed by 2 examiners. Nine studies comparing autografts and nonirradiated allografts were included. Six of the 9 studies compared bone-patellar tendon-bone (BPTB) autografts with BPTB allografts. Two studies compared hamstring tendon autografts to hamstring tendon allografts, and 1 study compared hamstring tendon autografts to tibialis anterior allografts. The mean patient age in 7 of 9 studies ranged from 24.5 to 32 years, with 1 study including only patients older than 40 years and another not reporting patient age. The mean follow-up duration was 24 to 94 months. Six of 9 studies reported clinical graft failure rates, 8 of 9 reported postoperative instrumented laxity measurements, 7 of 9 reported postoperative physical examination findings, and all studies reported patient-reported outcome scores. This review demonstrated no statistically significant difference between autografts and nonirradiated allografts in any outcome measure. No significant differences were found in graft failure rate, postoperative laxity, or patient-reported outcome scores when comparing ACLR with autografts to nonirradiated allografts in this systematic review. These findings apply to patients in their late 20s and early 30s. Caution is advised when considering extrapolation of these findings to younger, more active cohorts.

Where's Waldo? The 'decapitation gambit' and the definition of death.

PubMed

Lizza, John P

2011-12-01

The 'decapitation gambit' holds that, if physical decapitation normally entails the death of the human being, then physiological decapitation, evident in cases of total brain failure, entails the death of the human being. This argument has been challenged by Franklin Miller and Robert Truog, who argue that physical decapitation does not necessarily entail the death of human beings and that therefore, by analogy, artificially sustained human bodies with total brain failure are living human beings. They thus challenge the current neurological criterion for determining death and argue for a return to the traditional criterion of the irreversible loss of circulation and respiration. In this paper, I defend the decapitation gambit and total brain failure as a criterion for determining death against Miller and Truog's criticism.

Damage tolerance modeling and validation of a wireless sensory composite panel for a structural health monitoring system

NASA Astrophysics Data System (ADS)

Talagani, Mohamad R.; Abdi, Frank; Saravanos, Dimitris; Chrysohoidis, Nikos; Nikbin, Kamran; Ragalini, Rose; Rodov, Irena

2013-05-01

The paper proposes the diagnostic and prognostic modeling and test validation of a Wireless Integrated Strain Monitoring and Simulation System (WISMOS). The effort verifies a hardware and web based software tool that is able to evaluate and optimize sensorized aerospace composite structures for the purpose of Structural Health Monitoring (SHM). The tool is an extension of an existing suite of an SHM system, based on a diagnostic-prognostic system (DPS) methodology. The goal of the extended SHM-DPS is to apply multi-scale nonlinear physics-based Progressive Failure analyses to the "as-is" structural configuration to determine residual strength, remaining service life, and future inspection intervals and maintenance procedures. The DPS solution meets the JTI Green Regional Aircraft (GRA) goals towards low weight, durable and reliable commercial aircraft. It will take advantage of the currently developed methodologies within the European Clean sky JTI project WISMOS, with the capability to transmit, store and process strain data from a network of wireless sensors (e.g. strain gages, FBGA) and utilize a DPS-based methodology, based on multi scale progressive failure analysis (MS-PFA), to determine structural health and to advice with respect to condition based inspection and maintenance. As part of the validation of the Diagnostic and prognostic system, Carbon/Epoxy ASTM coupons were fabricated and tested to extract the mechanical properties. Subsequently two composite stiffened panels were manufactured, instrumented and tested under compressive loading: 1) an undamaged stiffened buckling panel; and 2) a damaged stiffened buckling panel including an initial diamond cut. Next numerical Finite element models of the two panels were developed and analyzed under test conditions using Multi-Scale Progressive Failure Analysis (an extension of FEM) to evaluate the damage/fracture evolution process, as well as the identification of contributing failure modes. The comparisons between predictions and test results were within 10% accuracy.

Report of the Presidential Commission on the Space Shuttle Challenger Accident, Volume 1

NASA Technical Reports Server (NTRS)

Rogers, W. P.; Armstrong, N. A.; Acheson, D. C.; Covert, E. E.; Feynman, R. P.; Hotz, R. B.; Kutyna, D. J.; Ride, S. K.; Rummel, R. W.; Sutter, J. F.

1986-01-01

The findings of the Commission regarding the circumstances surrounding the Challenger accident are reported and recommendations for corrective action are outlined. All available mission data, subsequent tests, and wreckage analyses were reviewed and specific failure scenarios were developed. The Commission concluded that the cause of the Mission 51-L accident was the failure of the pressure seal in the aft field joint of the right solid rocket motor. The failure was due to a faulty design unacceptably sensitive to a number of factors. These factors were the effects of temperature, physical dimensions, the character of materials, the effects of reuse, processing, and the reaction of the joint to dynamic loading. In addition to analyzing the material causes of the accident, the Commission examined the chain of decisions that culminated in approval of the launch. It concluded that the decision making process was flawed in several ways including (1) failure in communication resulting in a launch decision based on incomplete and misleading information, (2) a conflict between engineering data and management judgements, and (3) a NASA management structure that permitted flight safety problems to bypass key Shuttle managers.

Factors Contributing to Failure of Rotator Cuff Surgery in Persons with Work-Related Injuries

PubMed Central

Lincoln, Sandra; Axelrod, Terry; Holtby, Richard

2008-01-01

Purpose: Shoulder pain is a major musculoskeletal and economic concern in industrialized countries, with the rate of surgical failure reportedly higher in patients injured at work. The purposes of this study were (1) to examine the prevalence of identifiable causes of rotator cuff surgery failure and (2) to examine the relationship among the existence of these causes and outcome scores, patient expectations, and overall satisfaction. Methods: This was a cross-sectional study of patients who experienced continued impairments following surgical treatment for work-related injuries. The primary outcome was a disease-specific measure, the Western Ontario Rotator Cuff (WORC) index. Patients were categorized into two groups based on the existence of an identifiable reason for surgical failure vs. no reason for failure, as demonstrated by clinical and radiologic investigations and decided upon by a shoulder surgeon and a physical therapist. Analyses included a t-test for independent sample means, linear regression, non-parametric Wilcoxon test, and Fisher's exact test. Results: Thirty-eight consecutive patients were included in the study, and 24 causes of surgical failure were identified in 19 patients (50%). Overall, patients with findings of failure were more disabled according to the total WORC index and had higher levels of symptoms, emotional difficulties, and limitations in sports and recreational activities. Expectations and satisfaction levels were not significantly different between groups. Conclusion: Our results indicate that 50% of patients who reported failed surgery had at least one reason to explain their ongoing symptoms, emotional difficulties, and functional limitations. PMID:20145776

The Marfan Syndrome: Physical Activity Guidelines for Physical Educators, Coaches and Physicians.

ERIC Educational Resources Information Center

Romeo, Thomas J.

Intended for physical educators, this manual provides guidelines for providing safe and effective physical activity programs for children with Marfan syndrome, a congenital condition involving the connective tissues and the probable cause of sudden death by heart failure of some young competitive athletes in recent cases. The manual includes…

Memory Circuit Fault Simulator

NASA Technical Reports Server (NTRS)

Sheldon, Douglas J.; McClure, Tucker

2013-01-01

Spacecraft are known to experience significant memory part-related failures and problems, both pre- and postlaunch. These memory parts include both static and dynamic memories (SRAM and DRAM). These failures manifest themselves in a variety of ways, such as pattern-sensitive failures, timingsensitive failures, etc. Because of the mission critical nature memory devices play in spacecraft architecture and operation, understanding their failure modes is vital to successful mission operation. To support this need, a generic simulation tool that can model different data patterns in conjunction with variable write and read conditions was developed. This tool is a mathematical and graphical way to embed pattern, electrical, and physical information to perform what-if analysis as part of a root cause failure analysis effort.

High Power Laser Diode Array Qualification and Guidelines for Space Flight Environments

NASA Technical Reports Server (NTRS)

Ott, Melanie N.; Eegholm, Niels; Stephen, Mark; Leidecker, Henning; Plante, Jeannette; Meadows, Byron; Amzajerdian, Farzin; Jamison, Tracee; LaRocca, Frank

2006-01-01

High-power laser diode arrays (LDAs) are used for a variety of space-based remote sensor laser programs as an energy source for diode-pumped solid-state lasers. LDAs have been flown on NASA missions including MOLA, GLAS and MLA and have continued to be viewed as an important part of the laser-based instrument component suite. There are currently no military or NASA-grade, -specified, or - qualified LDAs available for "off-the-shelf" use by NASA programs. There has also been no prior attempt to define a standard screening and qualification test flow for LDAs for space applications. Initial reliability studies have also produced good results from an optical performance and stability standpoint. Usage experience has shown, howeve that the current designs being offered may be susceptible to catastrophic failures due to their physical construction (packaging) combined with the electro-optical operational modes and the environmental factors of space application. design combined with operational mode was at the root of the failures which have greatly reduced the functionality of the GLAS instrument. The continued need for LDAs for laser-based science instruments and past catastrophic failures of this part type demand examination of LDAs in a manner which enables NASA to select, buy, validate and apply them in a manner which poses as little risk to the success of the mission as possible.

In-patient physiotherapy for adults on veno-venous extracorporeal membrane oxygenation – United Kingdom ECMO Physiotherapy Network: A consensus agreement for best practice

PubMed Central

Purkiss, Claire; Cork, Gabriella; Baddeley, Adam; Morris, Kelly; Carey, Leah; Brown, Mike; McGarrigle, Laura; Kennedy, Samantha

2017-01-01

Clinical specialist physiotherapists from the five severe respiratory failure centres in England where respiratory extracorporeal membrane oxygenation (ECMO) is practiced have established this consensus agreement for physiotherapy best practice. The severe respiratory failure centres are Wythenshawe Hospital, Manchester; Glenfield Hospital, Leicester; Papworth Hospital, Cambridge; Guy’s and St Thomas’ Hospital, London and The Royal Brompton Hospital, London. Although research into physiotherapy and ECMO is increasing, there is not a sufficient amount to write evidence-based guidelines; hence the development of a consensus document, using knowledge and experience of the specialist physiotherapists working with patients receiving ECMO. The document outlines safety aspects, practicalities and additional treatment considerations for physiotherapists conducting respiratory care and physical rehabilitation. PMID:29118833

Reliability analysis for the smart grid : from cyber control and communication to physical manifestations of failure.

DOT National Transportation Integrated Search

2010-01-01

The Smart Grid is a cyber-physical system comprised of physical components, such as transmission lines and generators, and a : network of embedded systems deployed for their cyber control. Our objective is to qualitatively and quantitatively analyze ...

A physically-based method for predicting peak discharge of floods caused by failure of natural and constructed earthen dams

USGS Publications Warehouse

Walder, J.S.; O'Connor, J. E.; Costa, J.E.; ,

1997-01-01

We analyse a simple, physically-based model of breach formation in natural and constructed earthen dams to elucidate the principal factors controlling the flood hydrograph at the breach. Formation of the breach, which is assumed trapezoidal in cross-section, is parameterized by the mean rate of downcutting, k, the value of which is constrained by observations. A dimensionless formulation of the model leads to the prediction that the breach hydrograph depends upon lake shape, the ratio r of breach width to depth, the side slope ?? of the breach, and the parameter ?? = (V.D3)(k/???gD), where V = lake volume, D = lake depth, and g is the acceleration due to gravity. Calculations show that peak discharge Qp depends weakly on lake shape r and ??, but strongly on ??, which is the product of a dimensionless lake volume and a dimensionless erosion rate. Qp(??) takes asymptotically distinct forms depending on whether < ??? 1 or < ??? 1. Theoretical predictions agree well with data from dam failures for which k could be reasonably estimated. The analysis provides a rapid and in many cases graphical way to estimate plausible values of Qp at the breach.We analyze a simple, physically-based model of breach formation in natural and constructed earthen dams to elucidate the principal factors controlling the flood hydrograph at the breach. Formation of the breach, which is assumed trapezoidal in cross-section, is parameterized by the mean rate of downcutting, k, the value of which is constrained by observations. A dimensionless formulation of the model leads to the prediction that the breach hydrograph depends upon lake shape, the ratio r of breach width to depth, the side slope ?? of the breach, and the parameter ?? = (V/D3)(k/???gD), where V = lake volume, D = lake depth, and g is the acceleration due to gravity. Calculations show that peak discharge Qp depends weakly on lake shape r and ??, but strongly on ??, which is the product of a dimensionless lake volume and a dimensionless erosion rate. Qp(??) takes asymptotically distinct forms depending on whether ?????1 or ?????1. Theoretical predictions agree well with data from dam failures for which k could be reasonably estimated. The analysis provides a rapid and in many cases graphical way to estimate plausible values of Qp at the breach.

Anticipated affective consequences of physical activity adoption and maintenance.

PubMed

Dunton, Genevieve Fridlund; Vaughan, Elaine

2008-11-01

The expected emotional consequences of future actions are thought to play an important role in health behavior change. This research examined whether anticipated affective consequences of success and failure vary across stages of physical activity change and differentially predict physical activity adoption as compared to maintenance. Using a prospective design over a 3-month period, a community sample of 329 healthy, middle-aged adults were assessed at 2 time points. Anticipated positive and negative emotions, stage of behavior change (precontemplation [PC], contemplation [C], preparation [P], action [A], maintenance [M]), and level of physical activity. At baseline, anticipated positive emotions were greater in C versus PC, whereas anticipated negative emotions were greater in M versus A and in M versus P. Higher anticipated positive but not negative emotions predicted physical activity adoption and maintenance after 3 months. Although the expected affective consequences of future success and failure differentiated among individuals in the early and later stages of physical activity change, respectively; only the anticipated affective consequences of success predicted future behavior.

Reattachment of flexor digitorum profundus avulsion: biomechanical performance of 3 techniques.

PubMed

Brar, Ravinder; Owen, John R; Melikian, Raymond; Gaston, R Glenn; Wayne, Jennifer S; Isaacs, Jonathan E

2014-11-01

To investigate whether inclusion of the volar plate in repair of flexor digitorum profundus avulsions increases the strength of the repair and resists gapping. Cadaveric fingers (n = 18) were divided into 3 equal groups. The first technique involved 2 micro-suture anchors only (A). The second used only volar plate repair (VP). The third group was a hybrid, combining a micro-suture anchor with volar plate augmentation (AVP). Specimens were loaded cyclically to simulate passive motion rehabilitation before being loaded to failure. Clinical failure was defined as 3 mm of gapping, and physical failure as the highest load associated with hardware failure, suture breakage, anchor pullout, or volar plate avulsion. Gapping throughout cycling was significantly greater for the A group than VP and AVP with no difference detected between VP and AVP groups. Gapping exceeded 3 mm during cycling of 3 A specimens, but in none of the VP or AVP specimens. Load at clinical and physical failure for A was significantly lower than for VP and AVP, whereas no difference was detected between VP and AVP. In this cadaveric model, incorporating the volar plate conferred a significant advantage in strength, increasing the mean load to physical failure by approximately 100 N. According to previous biomechanical studies, current reconstructive strategies for flexor digitorum profundus zone I avulsions are not strong enough to withstand active motion rehabilitation. We demonstrated the potential use of volar plate augmentation and the prospective advantageous increase in strength in this cadaveric model. In vivo performance and effects on digital motion are not known. Copyright © 2014 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

Failure time analysis with unobserved heterogeneity: Earthquake duration time of Turkey

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ata, Nihal, E-mail: nihalata@hacettepe.edu.tr; Kadilar, Gamze Özel, E-mail: gamzeozl@hacettepe.edu.tr

Failure time models assume that all units are subject to same risks embodied in the hazard functions. In this paper, unobserved sources of heterogeneity that are not captured by covariates are included into the failure time models. Destructive earthquakes in Turkey since 1900 are used to illustrate the models and inter-event time between two consecutive earthquakes are defined as the failure time. The paper demonstrates how seismicity and tectonics/physics parameters that can potentially influence the spatio-temporal variability of earthquakes and presents several advantages compared to more traditional approaches.

Unified continuum damage model for matrix cracking in composite rotor blades

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pollayi, Hemaraju; Harursampath, Dineshkumar

This paper deals with modeling of the first damage mode, matrix micro-cracking, in helicopter rotor/wind turbine blades and how this effects the overall cross-sectional stiffness. The helicopter/wind turbine rotor system operates in a highly dynamic and unsteady environment leading to severe vibratory loads present in the system. Repeated exposure to this loading condition can induce damage in the composite rotor blades. These rotor/turbine blades are generally made of fiber-reinforced laminated composites and exhibit various competing modes of damage such as matrix micro-cracking, delamination, and fiber breakage. There is a need to study the behavior of the composite rotor system undermore » various key damage modes in composite materials for developing Structural Health Monitoring (SHM) system. Each blade is modeled as a beam based on geometrically non-linear 3-D elasticity theory. Each blade thus splits into 2-D analyzes of cross-sections and non-linear 1-D analyzes along the beam reference curves. Two different tools are used here for complete 3-D analysis: VABS for 2-D cross-sectional analysis and GEBT for 1-D beam analysis. The physically-based failure models for matrix in compression and tension loading are used in the present work. Matrix cracking is detected using two failure criterion: Matrix Failure in Compression and Matrix Failure in Tension which are based on the recovered field. A strain variable is set which drives the damage variable for matrix cracking and this damage variable is used to estimate the reduced cross-sectional stiffness. The matrix micro-cracking is performed in two different approaches: (i) Element-wise, and (ii) Node-wise. The procedure presented in this paper is implemented in VABS as matrix micro-cracking modeling module. Three examples are presented to investigate the matrix failure model which illustrate the effect of matrix cracking on cross-sectional stiffness by varying the applied cyclic load.« less

Diagnosis of Fanconi anemia in patients with bone marrow failure

PubMed Central

Pinto, Fernando O.; Leblanc, Thierry; Chamousset, Delphine; Le Roux, Gwenaelle; Brethon, Benoit; Cassinat, Bruno; Larghero, Jérôme; de Villartay, Jean-Pierre; Stoppa-Lyonnet, Dominique; Baruchel, André; Socié, Gérard; Gluckman, Eliane; Soulier, Jean

2009-01-01

Background Patients with bone marrow failure and undiagnosed underlying Fanconi anemia may experience major toxicity if given standard-dose conditioning regimens for hematopoietic stem cell transplant. Due to clinical variability and/or potential emergence of genetic reversion with hematopoietic somatic mosaicism, a straightforward Fanconi anemia diagnosis can be difficult to make, and diagnostic strategies combining different assays in addition to classical breakage tests in blood may be needed. Design and Methods We evaluated Fanconi anemia diagnosis on blood lymphocytes and skin fibroblasts from a cohort of 87 bone marrow failure patients (55 children and 32 adults) with no obvious full clinical picture of Fanconi anemia, by performing a combination of chromosomal breakage tests, FANCD2-monoubiquitination assays, a new flow cytometry-based mitomycin C sensitivity test in fibroblasts, and, when Fanconi anemia was diagnosed, complementation group and mutation analyses. The mitomycin C sensitivity test in fibroblasts was validated on control Fanconi anemia and non-Fanconi anemia samples, including other chromosomal instability disorders. Results When this diagnosis strategy was applied to the cohort of bone marrow failure patients, 7 Fanconi anemia patients were found (3 children and 4 adults). Classical chromosomal breakage tests in blood detected 4, but analyses on fibroblasts were necessary to diagnose 3 more patients with hematopoietic somatic mosaicism. Importantly, Fanconi anemia was excluded in all the other patients who were fully evaluated. Conclusions In this large cohort of patients with bone marrow failure our results confirmed that when any clinical/biological suspicion of Fanconi anemia remains after chromosome breakage tests in blood, based on physical examination, history or inconclusive results, then further evaluation including fibroblast analysis should be made. For that purpose, the flow-based mitomycin C sensitivity test here described proved to be a reliable alternative method to evaluate Fanconi anemia phenotype in fibroblasts. This global strategy allowed early and accurate confirmation or rejection of Fanconi anemia diagnosis with immediate clinical impact for those who underwent hematopoietic stem cell transplant. PMID:19278965

Failure Analysis and Prevention for the Air Logistics Center Engineer: CAStLE Course Development Summary

DTIC Science & Technology

2006-09-01

Monday through Friday in a single week. This daily schedule was chosen so that engineers could still access their office during part of the normal...aluminum, austenitic SS) structures do not cleave! "* Physical Manifestation - Bright, shiny appearance - " Crystallized " fracture surface - Chevrons...region with the "striations" Fracture mode was actually by SOC *Lesson? Don’t base conclusions on a single observation Higher mag macroscopic image

Major depressive disorder: a qualitative study on the experiences of Iranian patients.

PubMed

Amini, Kourosh; Negarandeh, Reza; Cheraghi, Mohammad Ali; Eftekhar, Mehrdad

2013-09-01

Major depressive disorder (MDD) is one the most common mental disorders; it affects about 5-10% of the world population. This study explores the experiences of people with major depressive disorder in Zanjan, Iran. In order to identify recurring themes and patterns in individuals' experiences of major depressive disorder, semi-structured interviews with 18 patients were recorded and transcribed verbatim. The transcripts were then analyzed based on conventional qualitative content analysis. Five main categories emerged. The first category was called emotional paralysis and included the subcategories feeling severely depressed; feeling anxious; feeling impatient and irritable; and having dyshedonia. The second category was disturbance of thinking and was comprised of the subcategories of preoccupation, instable spiritual beliefs, and guilt. Cognitive decline was the third identified category and was further divided into subcategories of frustration, unawareness of the disorder, negative evaluation, indecisiveness, and loss of focus and loss of memory. Another major category was physical illnesses with the subcategories of physical discomfort, sleep problems, appetite disturbance, facial changes, sexual dysfunction, and medical conditions. The final category was failure in life, which had failure in personal affairs, jeopardized interpersonal relations, and unstable work life as subcategories. These findings provide a base for further research in this area. They also have clinical relevance for health care providers working with patients with MDD. Related cultural issues also are discussed.

Microcircuit failure analysis using the SEM. [Scanning Electron Microscopes

NASA Technical Reports Server (NTRS)

Nicolas, D. P.

1974-01-01

The scanning electron microscope adds a new dimension to the knowledge that can be obtained from a failed microcircuit. When used with conventional techniques, SEM assists and clarifies the analysis, but it does not replace light microscopy. The most advantageous features for microcircuit analysis are long working distances and great depth of field. Manufacturer related failure modes of microcircuits are metallization defects, poor bonding, surface and particle contamination, and design and fabrication faults. User related failure modes are caused by abuse, such as overstress. The Physics of Failure Procedure followed by the Astrionics Laboratory in failure analysis is described, which is designed to obtain maximum information available from each step.

A Comprehensive Availability Modeling and Analysis of a Virtualized Servers System Using Stochastic Reward Nets

PubMed Central

Kim, Dong Seong; Park, Jong Sou

2014-01-01

It is important to assess availability of virtualized systems in IT business infrastructures. Previous work on availability modeling and analysis of the virtualized systems used a simplified configuration and assumption in which only one virtual machine (VM) runs on a virtual machine monitor (VMM) hosted on a physical server. In this paper, we show a comprehensive availability model using stochastic reward nets (SRN). The model takes into account (i) the detailed failures and recovery behaviors of multiple VMs, (ii) various other failure modes and corresponding recovery behaviors (e.g., hardware faults, failure and recovery due to Mandelbugs and aging-related bugs), and (iii) dependency between different subcomponents (e.g., between physical host failure and VMM, etc.) in a virtualized servers system. We also show numerical analysis on steady state availability, downtime in hours per year, transaction loss, and sensitivity analysis. This model provides a new finding on how to increase system availability by combining both software rejuvenations at VM and VMM in a wise manner. PMID:25165732

The "Ins" and "Outs" of Physical Activity Policy Implementation: Inadequate Capacity, Inappropriate Outcome Measures, and Insufficient Funds

ERIC Educational Resources Information Center

Howie, Erin K.; Stevick, E. Doyle

2014-01-01

Background: Despite broad public support and legislative activity, policies intended to promote physical activity in schools have not produced positive outcomes in levels of physical activity or student health. What explains the broad failure of Physical Activity Policies (PAPs)? Thus far, PAP research has used limited quantitative methods to…

Cyberspace security system

DOEpatents

Abercrombie, Robert K; Sheldon, Frederick T; Ferragut, Erik M

2014-06-24

A system evaluates reliability, performance and/or safety by automatically assessing the targeted system's requirements. A cost metric quantifies the impact of failures as a function of failure cost per unit of time. The metrics or measurements may render real-time (or near real-time) outcomes by initiating active response against one or more high ranked threats. The system may support or may be executed in many domains including physical domains, cyber security domains, cyber-physical domains, infrastructure domains, etc. or any other domains that are subject to a threat or a loss.

Survey of Failure in Engineering Education and Industry

NASA Astrophysics Data System (ADS)

Arimitsu, Yutaka; Yagi, Hidetsugu

Students have failure experiences in the project-based learning but they do not profess their experiences. On the other hand, failures and accidents, in the industrial world, are analyzed frequently, and a knowledge data base on failure and QC activities have been introduced. To turn failure experience in education to advantage, the authors survey the properties of failures in project based learning and views of students, teachers and managers of design divisions in companies. Teachers and students regard failure experiences as instructive and acceptable. The typical causes of failure in educational institutions are luck of skill in manufacturing and inadequate planning, which are minor causes of failure in the industry. To establish a knowledge data base on failure in educational institutions, properties of failure in education should be taken into account.

Burn Severity and Its Impact on Soil Properties: 2016 Erskine Fire in the Southern Sierra Nevada

NASA Astrophysics Data System (ADS)

Haake, S.; Guo, J.; Krugh, W. C.

2017-12-01

Wildfire frequency in the southern Sierra Nevada has increased over the past decades. The effects of wildfires on soils can increase the frequency of slope failure and debris flow events, which pose a greater risk to people, as human populations expand into foothill and mountainous communities of the Sierra Nevada. Alterations in the physical properties of burned soils are one such effect that can catalyze slope failure and debris flow events. Moreover, the degree of a soil's physical alteration resulting from wildfire is linked to fire intensity. The 2016 Erskine fire occurred in the southern Sierra Nevada, burning 48,019 acres, resulting in soils of unburned, low, moderate, and high burn severities. In this study, the physical properties of soils with varying degrees of burn severity are explored within the 2016 Erskine fire perimeter. The results constrain the effects of burn severity on soil's physical properties. Unburned, low, moderate, and high burn severity soil samples were collected within the Erskine fire perimeter. Alterations in soils' physical properties resulting from burn severity are explored using X-ray diffractometry analysis, liquid limit, plastic limit, and shear strength tests. Preliminary results from this study will be used to assess debris flow and slope failure hazard models within burned areas of the Kern River watershed in the southern Sierra Nevada.

A dislocation-based crystal plasticity framework for dynamic ductile failure of single crystals

NASA Astrophysics Data System (ADS)

Nguyen, Thao; Luscher, D. J.; Wilkerson, J. W.

2017-11-01

A framework for dislocation-based viscoplasticity and dynamic ductile failure has been developed to model high strain rate deformation and damage in single crystals. The rate-dependence of the crystal plasticity formulation is based on the physics of relativistic dislocation kinetics suited for extremely high strain rates. The damage evolution is based on the dynamics of void growth, which are governed by both micro-inertia as well as dislocation kinetics and dislocation substructure evolution. An averaging scheme is proposed in order to approximate the evolution of the dislocation substructure in both the macroscale as well as its spatial distribution at the microscale. Additionally, a concept of a single equivalent dislocation density that effectively captures the collective influence of dislocation density on all active slip systems is proposed here. Together, these concepts and approximations enable the use of semi-analytic solutions for void growth dynamics developed in (Wilkerson and Ramesh, 2014), which greatly reduce the computational overhead that would otherwise be required. The resulting homogenized framework has been implemented into a commercially available finite element package, and a validation study against a suite of direct numerical simulations was carried out.

Speedy routing recovery protocol for large failure tolerance in wireless sensor networks.

PubMed

Lee, Joa-Hyoung; Jung, In-Bum

2010-01-01

Wireless sensor networks are expected to play an increasingly important role in data collection in hazardous areas. However, the physical fragility of a sensor node makes reliable routing in hazardous areas a challenging problem. Because several sensor nodes in a hazardous area could be damaged simultaneously, the network should be able to recover routing after node failures over large areas. Many routing protocols take single-node failure recovery into account, but it is difficult for these protocols to recover the routing after large-scale failures. In this paper, we propose a routing protocol, referred to as ARF (Adaptive routing protocol for fast Recovery from large-scale Failure), to recover a network quickly after failures over large areas. ARF detects failures by counting the packet losses from parent nodes, and upon failure detection, it decreases the routing interval to notify the neighbor nodes of the failure. Our experimental results indicate that ARF could provide recovery from large-area failures quickly with less packets and energy consumption than previous protocols.

Development of new physical activity and sedentary behavior change self-efficacy questionnaires using item response modeling

USDA-ARS?s Scientific Manuscript database

Theoretically, increased levels of physical activity self-efficacy (PASE) should lead to increased physical activity, but few studies have reported this effect among youth. This failure may be at least partially attributable to measurement limitations. In this study, Item Response Modeling (IRM) was...

Elementary students' engagement in failure-prone engineering design tasks

NASA Astrophysics Data System (ADS)

Andrews, Chelsea Joy

Although engineering education has been practiced at the undergraduate level for over a century, only fairly recently has the field broadened to include the elementary level; the pre-college division of the American Society of Engineering Education was established in 2003. As a result, while recent education standards require engineering in elementary schools, current studies are still filling in basic research on how best to design and implement elementary engineering activities. One area in need of investigation is how students engage with physical failure in design tasks. In this dissertation, I explore how upper elementary students engage in failure-prone engineering design tasks in an out-of-school environment. In a series of three empirical case studies, I look closely at how students evaluate failed tests and decide on changes to their design constructions, how their reasoning evolves as they repeatedly encounter physical failure, and how students and facilitators co-construct testing norms where repetitive failure is manageable. I also briefly investigate how students' engagement differs in a task that features near-immediate success. By closely examining student groups' discourse and their interactions with their design constructions, I found that these students: are able to engage in iteration and see failure-as-feedback with minimal externally-imposed structure; seem to be designing in a more sophisticated manner, attending to multiple causal factors, after experiencing repetitive failure; and are able to manage the stress and frustration of repetitive failure, provided the co-constructed testing norms of the workshop environment are supportive of failure management. These results have both pedagogical implications, in terms of how to create and facilitate design tasks, and methodological implications--namely, I highlight the particular insights afforded by a case study approach for analyzing engagement in design tasks.

Probability of failure prediction for step-stress fatigue under sine or random stress

NASA Technical Reports Server (NTRS)

Lambert, R. G.

1979-01-01

A previously proposed cumulative fatigue damage law is extended to predict the probability of failure or fatigue life for structural materials with S-N fatigue curves represented as a scatterband of failure points. The proposed law applies to structures subjected to sinusoidal or random stresses and includes the effect of initial crack (i.e., flaw) sizes. The corrected cycle ratio damage function is shown to have physical significance.

Factors influencing change in walking ability in patients with heart failure undergoing exercise-based cardiac rehabilitation.

PubMed

Sutherland, Natasha; Harrison, Alexander; Doherty, Patrick

2018-05-17

Exercise-based cardiac rehabilitation (CR) is an effective intervention for patients with heart failure (HF), in which one of the main targets is to increase physical capacity. In the HF population this is traditionally assessed using distance covered during a walking test. This study aims to establish the extent to which change in walking ability, in HF patients attending CR, is determined by patient characteristics and service provision. The study utilised routine clinical data from the National Audit of Cardiac Rehabilitation to perform a robust analysis. Change, in metres, between pre- and post-CR six-minute walk tests was calculated. Multivariate linear regression models were used to explore the relationship between patient characteristics, service-level variables, and change in metres walked. Complete and valid data from 633 patients was analysed, and a mean change of 51.30 m was calculated. Female gender (-34.13 m, p = 0.007), being retired (-36.41 m, p = 0.001) and being married/in a relationship (-32.54 m, p = 0.023) were all significant negative predictors of change. There was an additional negative relationship with body mass index (BMI) whereby for every unit increase in BMI, predicted change reduces by 2.48 m (p = 0.006). This study identified significant patient-level characteristics strongly associated with limited improvement in walking ability following CR. Improving physical capacity is a core component of CR, therefore services should aim to account for baseline characteristics identified in this study as part of tailoring the CR intervention around the individual. Pre- and post-CR physical capacity assessments, which constitute minimum standards for CR, are worryingly low and should be given high priority. Copyright © 2017. Published by Elsevier B.V.

Specification of the near-Earth space environment with SHIELDS

DOE PAGES

Jordanova, Vania Koleva; Delzanno, Gian Luca; Henderson, Michael Gerard; ...

2017-11-26

Here, predicting variations in the near-Earth space environment that can lead to spacecraft damage and failure is one example of “space weather” and a big space physics challenge. A project recently funded through the Los Alamos National Laboratory (LANL) Directed Research and Development (LDRD) program aims at developing a new capability to understand, model, and predict Space Hazards Induced near Earth by Large Dynamic Storms, the SHIELDS framework. The project goals are to understand the dynamics of the surface charging environment (SCE), the hot (keV) electrons representing the source and seed populations for the radiation belts, on both macro- andmore » micro-scale. Important physics questions related to particle injection and acceleration associated with magnetospheric storms and substorms, as well as plasma waves, are investigated. These challenging problems are addressed using a team of world-class experts in the fields of space science and computational plasma physics, and state-of-the-art models and computational facilities. A full two-way coupling of physics-based models across multiple scales, including a global MHD (BATS-R-US) embedding a particle-in-cell (iPIC3D) and an inner magnetosphere (RAM-SCB) codes, is achieved. New data assimilation techniques employing in situ satellite data are developed; these provide an order of magnitude improvement in the accuracy in the simulation of the SCE. SHIELDS also includes a post-processing tool designed to calculate the surface charging for specific spacecraft geometry using the Curvilinear Particle-In-Cell (CPIC) code that can be used for reanalysis of satellite failures or for satellite design.« less

Specification of the near-Earth space environment with SHIELDS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jordanova, Vania Koleva; Delzanno, Gian Luca; Henderson, Michael Gerard

Here, predicting variations in the near-Earth space environment that can lead to spacecraft damage and failure is one example of “space weather” and a big space physics challenge. A project recently funded through the Los Alamos National Laboratory (LANL) Directed Research and Development (LDRD) program aims at developing a new capability to understand, model, and predict Space Hazards Induced near Earth by Large Dynamic Storms, the SHIELDS framework. The project goals are to understand the dynamics of the surface charging environment (SCE), the hot (keV) electrons representing the source and seed populations for the radiation belts, on both macro- andmore » micro-scale. Important physics questions related to particle injection and acceleration associated with magnetospheric storms and substorms, as well as plasma waves, are investigated. These challenging problems are addressed using a team of world-class experts in the fields of space science and computational plasma physics, and state-of-the-art models and computational facilities. A full two-way coupling of physics-based models across multiple scales, including a global MHD (BATS-R-US) embedding a particle-in-cell (iPIC3D) and an inner magnetosphere (RAM-SCB) codes, is achieved. New data assimilation techniques employing in situ satellite data are developed; these provide an order of magnitude improvement in the accuracy in the simulation of the SCE. SHIELDS also includes a post-processing tool designed to calculate the surface charging for specific spacecraft geometry using the Curvilinear Particle-In-Cell (CPIC) code that can be used for reanalysis of satellite failures or for satellite design.« less

Yoga for Heart Failure: A Review and Future Research

PubMed Central

Pullen, Paula R; Seffens, William S; Thompson, Walter R

2018-01-01

Background: Complementary and alternative medicine is a rapidly growing area of biomedical inquiry. Yoga has emerged in the forefront of holistic medical care due to its long history of linking physical, mental, and spiritual well-being. Research in yoga therapy (YT) has associated improved cardiovascular and quality of life (QoL) outcomes for the special needs of heart failure (HF) patients. Aim: The aim of this study is to review yoga intervention studies on HF patients, discuss proposed mechanisms, and examine yoga's effect on physiological systems that have potential benefits for HF patients. Second, to recommend future research directions to find the most effective delivery methods of yoga to medically stable HF patients. Methods: The authors conducted a systematic review of the medical literature for RCTs involving HF patients as participants in yoga interventions and for studies utilizing mechanistic theories of stretch and new technologies. We examined physical intensity, mechanistic theories, and the use of the latest technologies. Conclusions: Based on the review, there is a need to further explore yoga mechanisms and research options for the delivery of YT. Software apps as exergames developed for use at home and community activity centers may minimize health disparities and increase QoL for HF patients. PMID:29755216

Yoga for Heart Failure: A Review and Future Research.

PubMed

Pullen, Paula R; Seffens, William S; Thompson, Walter R

2018-01-01

Complementary and alternative medicine is a rapidly growing area of biomedical inquiry. Yoga has emerged in the forefront of holistic medical care due to its long history of linking physical, mental, and spiritual well-being. Research in yoga therapy (YT) has associated improved cardiovascular and quality of life (QoL) outcomes for the special needs of heart failure (HF) patients. The aim of this study is to review yoga intervention studies on HF patients, discuss proposed mechanisms, and examine yoga's effect on physiological systems that have potential benefits for HF patients. Second, to recommend future research directions to find the most effective delivery methods of yoga to medically stable HF patients. The authors conducted a systematic review of the medical literature for RCTs involving HF patients as participants in yoga interventions and for studies utilizing mechanistic theories of stretch and new technologies. We examined physical intensity, mechanistic theories, and the use of the latest technologies. Based on the review, there is a need to further explore yoga mechanisms and research options for the delivery of YT. Software apps as exergames developed for use at home and community activity centers may minimize health disparities and increase QoL for HF patients.

American Heart Association's Life's Simple 7: Avoiding Heart Failure and Preserving Cardiac Structure and Function.

PubMed

Folsom, Aaron R; Shah, Amil M; Lutsey, Pamela L; Roetker, Nicholas S; Alonso, Alvaro; Avery, Christy L; Miedema, Michael D; Konety, Suma; Chang, Patricia P; Solomon, Scott D

2015-09-01

Many people may underappreciate the role of lifestyle in avoiding heart failure. We estimated whether greater adherence in middle age to American Heart Association's Life's Simple 7 guidelines—on smoking, body mass, physical activity, diet, cholesterol, blood pressure, and glucose—is associated with lower lifetime risk of heart failure and greater preservation of cardiac structure and function in old age. We studied the population-based Atherosclerosis Risk in Communities Study cohort of 13,462 adults ages 45-64 years in 1987-1989. From the 1987-1989 risk factor measurements, we created a Life's Simple 7 score (range 0-14, giving 2 points for ideal, 1 point for intermediate, and 0 points for poor components). We identified 2218 incident heart failure events using surveillance of hospital discharge and death codes through 2011. In addition, in 4855 participants free of clinical cardiovascular disease in 2011-2013, we performed echocardiography from which we quantified left ventricular hypertrophy and diastolic dysfunction. One in four participants (25.5%) developed heart failure through age 85 years. Yet, this lifetime heart failure risk was 14.4% for those with a middle-age Life's Simple 7 score of 10-14 (optimal), 26.8% for a score of 5-9 (average), and 48.6% for a score of 0-4 (inadequate). Among those with no clinical cardiovascular event, the prevalence of left ventricular hypertrophy in late life was approximately 40% as common, and diastolic dysfunction was approximately 60% as common, among those with an optimal middle-age Life's Simple 7 score, compared with an inadequate score. Greater achievement of American Heart Association's Life's Simple 7 in middle age is associated with a lower lifetime occurrence of heart failure and greater preservation of cardiac structure and function. Copyright © 2015 Elsevier Inc. All rights reserved.

Time-dependent earthquake probabilities

USGS Publications Warehouse

Gomberg, J.; Belardinelli, M.E.; Cocco, M.; Reasenberg, P.

2005-01-01

We have attempted to provide a careful examination of a class of approaches for estimating the conditional probability of failure of a single large earthquake, particularly approaches that account for static stress perturbations to tectonic loading as in the approaches of Stein et al. (1997) and Hardebeck (2004). We have loading as in the framework based on a simple, generalized rate change formulation and applied it to these two approaches to show how they relate to one another. We also have attempted to show the connection between models of seismicity rate changes applied to (1) populations of independent faults as in background and aftershock seismicity and (2) changes in estimates of the conditional probability of failures of different members of a the notion of failure rate corresponds to successive failures of different members of a population of faults. The latter application requires specification of some probability distribution (density function of PDF) that describes some population of potential recurrence times. This PDF may reflect our imperfect knowledge of when past earthquakes have occurred on a fault (epistemic uncertainty), the true natural variability in failure times, or some combination of both. We suggest two end-member conceptual single-fault models that may explain natural variability in recurrence times and suggest how they might be distinguished observationally. When viewed deterministically, these single-fault patch models differ significantly in their physical attributes, and when faults are immature, they differ in their responses to stress perturbations. Estimates of conditional failure probabilities effectively integrate over a range of possible deterministic fault models, usually with ranges that correspond to mature faults. Thus conditional failure probability estimates usually should not differ significantly for these models. Copyright 2005 by the American Geophysical Union.

The Readiness of High School Students to Pursue First Year Physics

ERIC Educational Resources Information Center

Ramnarain, U.; Molefe, P.

2012-01-01

A high failure rate at first year physics is often attributed to the lack of readiness of high school students to pursue such studies. This research explores this issue and reports on the perceptions of five physics lecturers at a South African university on the preparedness of high school students for first year physics. Qualitative data was…

Preventing Early Learning Failure.

ERIC Educational Resources Information Center

Sornson, Bob, Ed.

Noting that thousands of young children with the capacity to experience school success do not because they are unprepared for school learning activities, have experienced physical or emotional setbacks that cause them to be at risk for early learning failure, have never experienced limits on their behavior, or have mild sensory or motor deficits,…

Vibration detection of component health and operability

NASA Technical Reports Server (NTRS)

Baird, B. C.

1975-01-01

In order to prevent catastrophic failure and eliminate unnecessary periodic maintenance in the shuttle orbiter program environmental control system components, some means of detecting incipient failure in these components is required. The utilization was investigated of vibrational/acoustic phenomena as one of the principal physical parameters on which to base the design of this instrumentation. Baseline vibration/acoustic data was collected from three aircraft type fans and two aircraft type pumps over a frequency range from a few hertz to greater than 3000 kHz. The baseline data included spectrum analysis of the baseband vibration signal, spectrum analysis of the detected high frequency bandpass acoustic signal, and amplitude distribution of the high frequency bandpass acoustic signal. A total of eight bearing defects and two unbalancings was introduced into the five test items. All defects were detected by at least one of a set of vibration/acoustic parameters with a margin of at least 2:1 over the worst case baseline. The design of a portable instrument using this set of vibration/acoustic parameters for detecting incipient failures in environmental control system components is described.

Assuring reliability program effectiveness.

NASA Technical Reports Server (NTRS)

Ball, L. W.

1973-01-01

An attempt is made to provide simple identification and description of techniques that have proved to be most useful either in developing a new product or in improving reliability of an established product. The first reliability task is obtaining and organizing parts failure rate data. Other tasks are parts screening, tabulation of general failure rates, preventive maintenance, prediction of new product reliability, and statistical demonstration of achieved reliability. Five principal tasks for improving reliability involve the physics of failure research, derating of internal stresses, control of external stresses, functional redundancy, and failure effects control. A final task is the training and motivation of reliability specialist engineers.

Integrated condition monitoring of a fleet of offshore wind turbines with focus on acceleration streaming processing

NASA Astrophysics Data System (ADS)

Helsen, Jan; Gioia, Nicoletta; Peeters, Cédric; Jordaens, Pieter-Jan

2017-05-01

Particularly offshore there is a trend to cluster wind turbines in large wind farms, and in the near future to operate such a farm as an integrated power production plant. Predictability of individual turbine behavior across the entire fleet is key in such a strategy. Failure of turbine subcomponents should be detected well in advance to allow early planning of all necessary maintenance actions; Such that they can be performed during low wind and low electricity demand periods. In order to obtain the insights to predict component failure, it is necessary to have an integrated clean dataset spanning all turbines of the fleet for a sufficiently long period of time. This paper illustrates our big-data approach to do this. In addition, advanced failure detection algorithms are necessary to detect failures in this dataset. This paper discusses a multi-level monitoring approach that consists of a combination of machine learning and advanced physics based signal-processing techniques. The advantage of combining different data sources to detect system degradation is in the higher certainty due to multivariable criteria. In order to able to perform long-term acceleration data signal processing at high frequency a streaming processing approach is necessary. This allows the data to be analysed as the sensors generate it. This paper illustrates this streaming concept on 5kHz acceleration data. A continuous spectrogram is generated from the data-stream. Real-life offshore wind turbine data is used. Using this streaming approach for calculating bearing failure features on continuous acceleration data will support failure propagation detection.

Experimental and failure analysis of the prosthetic finger joint implants

NASA Astrophysics Data System (ADS)

Naidu, Sanjiv H.

Small joint replacement arthroplasty of the hand is a well accepted surgical procedure to restore function and cosmesis in an individual with a crippled hand. Silicone elastomers have been used as prosthetic material in various small hand joints for well over three decades. Although the clinical science aspects of silicone elastomer failure are well known, the physical science aspects of prosthetic failure are scant and vague. In the following thesis, using both an animal model, and actual retrieved specimens which have failed in human service, experimental and failure analysis of silicone finger joints are presented. Fractured surfaces of retrieved silicone trapezial implants, and silicone finger joint implants were studied with both FESEM and SEM; the mode of failure for silicone trapezium is by wear polishing, whereas the finger joint implants failed either by fatigue fracture or tearing of the elastomer, or a combination of both. Thermal analysis revealed that the retrieved elastomer implants maintained its viscoelastic properties throughout the service period. In order to provide for a more functional and physiologic arthroplasty a novel finger joint (Rolamite prosthesis) is proposed using more recently developed thermoplastic polymers. The following thesis also addresses the outcome of the experimental studies of the Rolamite prosthesis in a rabbit animal model, in addition to the failure analysis of the thermoplastic polymers while in service in an in vivo synovial environment. Results of retrieved Rolamite specimens suggest that the use for thermoplastic elastomers such as block copolymer based elastomers in a synovial environment such as a mammalian joint may very well be limited.

Prognostics of Power Electronics, Methods and Validation Experiments

NASA Technical Reports Server (NTRS)

Kulkarni, Chetan S.; Celaya, Jose R.; Biswas, Gautam; Goebel, Kai

2012-01-01

Abstract Failure of electronic devices is a concern for future electric aircrafts that will see an increase of electronics to drive and control safety-critical equipment throughout the aircraft. As a result, investigation of precursors to failure in electronics and prediction of remaining life of electronic components is of key importance. DC-DC power converters are power electronics systems employed typically as sourcing elements for avionics equipment. Current research efforts in prognostics for these power systems focuses on the identification of failure mechanisms and the development of accelerated aging methodologies and systems to accelerate the aging process of test devices, while continuously measuring key electrical and thermal parameters. Preliminary model-based prognostics algorithms have been developed making use of empirical degradation models and physics-inspired degradation model with focus on key components like electrolytic capacitors and power MOSFETs (metal-oxide-semiconductor-field-effect-transistor). This paper presents current results on the development of validation methods for prognostics algorithms of power electrolytic capacitors. Particularly, in the use of accelerated aging systems for algorithm validation. Validation of prognostics algorithms present difficulties in practice due to the lack of run-to-failure experiments in deployed systems. By using accelerated experiments, we circumvent this problem in order to define initial validation activities.

Effects of physical guidance on short-term learning of walking on a narrow beam.

PubMed

Domingo, Antoinette; Ferris, Daniel P

2009-11-01

Physical guidance is often used in rehabilitation when teaching patients to re-learn movements. However, the effects of guidance on motor learning of complex skills, such as walking balance, are not clear. We tested four groups of healthy subjects that practiced walking on a narrow (1.27 cm) or wide (2.5 cm) treadmill-mounted balance beam, with or without physical guidance. Assistance was given by springs attached to a hip belt that applied restoring forces towards beam center. Subjects were evaluated while walking unassisted before and after training by calculating the number of times subjects stepped off of the beam per minute of successful walking on the beam (Failures per Minute). Subjects in Unassisted groups had greater performance improvements in walking balance from pre to post compared to subjects in Assisted groups. During training, Unassisted groups had more Failures per Minute than Assisted groups. Performance improvements were smaller in Narrow Beam groups than in Wide Beam groups. The Unassisted-Wide and Assisted-Narrow groups had similar Failures per Minute during training, but the Unassisted-Wide group had much greater performance gains after training. These results suggest that physical assistance can hinder motor learning of walking balance, assistance appears less detrimental for more difficult tasks, and task-specific dynamics are important to learning independent of error experience.

Causal Modeling of Secondary Science Students' Intentions to Enroll in Physics.

ERIC Educational Resources Information Center

Crawley, Frank E.; Black, Carolyn B.

1992-01-01

Reports a study using the causal modeling method to verify underlying causes of student interest in enrolling in physics as predicted by the theory of planned behavior. Families were identified as major referents in the social support system for physics enrollment. Course and extracurricular conflicts and fear of failure were primary beliefs…

EDITORIAL: Fracture: from the atomic to the geophysical scale Fracture: from the atomic to the geophysical scale

NASA Astrophysics Data System (ADS)

Bouchaud, Elisabeth; Soukiassian, Patrick

2009-11-01

Although fracture is a very common experience in every day life, it still harbours many unanswered questions. New avenues of investigation arise concerning the basic mechanisms leading to deformation and failure in heterogeneous materials, particularly in non-metals. The processes involved are even more complex when plasticity, thermal fluctuations or chemical interactions between the material and its environment introduce a specific time scale. Sub-critical failure, which may be reached at unexpectedly low loads, is particularly important for silicate glasses. Another source of complications originates from dynamic fracture, when loading rates become so high that the acoustic waves produced by the crack interact with the material heterogeneities, in turn producing new waves that modify the propagation. Recent progress in experimental techniques, allowing one to test and probe materials at sufficiently small length or time scales or in three dimensions, has led to a quantitative understanding of the physical processes involved. In parallel, simulations have also progressed, by extending the time and length scales they are able to reach, and thus attaining experimentally accessible conditions. However, one central question remains the inclusion of these basic mechanisms into a statistical description. This is not an easy task, mostly because of the strong stress gradients present at the tip of a crack, and because the averaging of fracture properties over a heterogeneous material, containing more or less brittle phases, requires rare event statistics. Substantial progress has been made in models and simulations based on accurate experiments. From these models, scaling laws have been derived, linking the behaviour at a micro- or even nano-scale to the macroscopic and even to geophysical scales. The reviews in this Cluster Issue of Journal of Physics D: Applied Physics cover several of these important topics, including the physical processes in fracture mechanisms, the sub-critical failure issue, the dynamical fracture propagation, and the scaling laws from the micro- to the geophysical scales. Achievements and progress are reported, and the many open questions are discussed, which should provide a sound basis for present and future prospects.

Physical rehabilitation for lung transplant candidates and recipients: An evidence-informed clinical approach

PubMed Central

Wickerson, Lisa; Rozenberg, Dmitry; Janaudis-Ferreira, Tania; Deliva, Robin; Lo, Vincent; Beauchamp, Gary; Helm, Denise; Gottesman, Chaya; Mendes, Polyana; Vieira, Luciana; Herridge, Margaret; Singer, Lianne G; Mathur, Sunita

2016-01-01

Physical rehabilitation of lung transplant candidates and recipients plays an important in optimizing physical function prior to transplant and facilitating recovery of function post-transplant. As medical and surgical interventions in lung transplantation have evolved over time, there has been a demographic shift of individuals undergoing lung transplantation including older individuals, those with multiple co-morbidites, and candidates with respiratory failure requiring bridging to transplantation. These changes have an impact on the rehabilitation needs of lung transplant candidates and recipients. This review provides a practical approach to rehabilitation based on research and clinical practice at our transplant centre. It focuses on functional assessment and exercise prescription during an uncomplicated and complicated clinical course in the pre-transplant, early and late post-transplant periods. The target audience includes clinicians involved in pre- and post-transplant patient care and rehabilitation researchers. PMID:27683630

Characterizing Slow Slip Applying Machine Learning

NASA Astrophysics Data System (ADS)

Hulbert, C.; Rouet-Leduc, B.; Bolton, D. C.; Ren, C. X.; Marone, C.; Johnson, P. A.

2017-12-01

Over the last two decades it has become apparent from strain and GPS measurements, that slow slip on earthquake faults is a widespread phenomenon. Slow slip is also inferred from small amplitude seismic signals known as tremor and low frequency earthquakes (LFE's) and has been reproduced in laboratory studies, providing useful physical insight into the frictional properties associated with the behavior. From such laboratory studies we ask whether we can obtain quantitative information regarding the physics of friction from only the recorded continuous acoustical data originating from the fault zone. We show that by applying machine learning to the acoustical signal, we can infer upcoming slow slip failure initiation as well as the slip termination, and that we can also infer the magnitudes by a second machine learning procedure based on predicted inter-event times. We speculate that by applying this or other machine learning approaches to continuous seismic data, new information regarding the physics of faulting could be obtained.

Recurrent Pericarditis: Modern Approach in 2016.

PubMed

Imazio, Massimo; Adler, Yehuda; Charron, Philippe

2016-06-01

Recurrent pericarditis is one of the most troublesome complications of pericarditis occurring in about one third of patients with a previous attack of pericarditis. The pathogenesis is presumed to be autoimmune and/or autoinflammatory in most cases. The mainstay of therapy for recurrences is physical restriction and anti-inflammatory therapy based on aspirin or NSAID plus colchicine. Corticosteroids at low to moderate doses (e.g., prednisone 0.2 to 0.5 mg/kg/day) should be considered only after failure of aspirin/NSAID (and more than one of these drugs) or for specific indications (e.g., pregnancy, systemic inflammatory diseases on steroids, renal failure, concomitant oral anticoagulant therapy). One of the most challenging issues is how to cope with patients who have recurrences despite colchicine. A small subset of patients (about 5 %) may develop corticosteroid-dependence and colchicine resistance. Among the emerging treatments, the three most common and evidence-based therapies are based on azathioprine, human intravenous immunoglobulin (IVIG), and anakinra. After failure of all options of medical therapy or for those patients who do not tolerate medical therapy or have serious adverse events related to medical therapy, the last possible option is the surgical removal of the pericardium. Total or radical pericardiectomy is recommended in these cases in experienced centers performing this surgery. A stepwise approach is recommended starting from NSAID and colchicine, corticosteroid and colchicine, a combination of the three options (NSAID, colchicine and corticosteroids), then azathioprine, IVIG, or anakinra as last medical options before pericardiectomy.

Does improvement in self-management skills predict improvement in quality of life and depressive symptoms? A prospective study in patients with heart failure up to one year after self-management education.

PubMed

Musekamp, Gunda; Schuler, Michael; Seekatz, Bettina; Bengel, Jürgen; Faller, Hermann; Meng, Karin

2017-02-15

Heart failure (HF) patient education aims to foster patients' self-management skills. These are assumed to bring about, in turn, improvements in distal outcomes such as quality of life. The purpose of this study was to test the hypothesis that change in self-reported self-management skills observed after participation in self-management education predicts changes in physical and mental quality of life and depressive symptoms up to one year thereafter. The sample comprised 342 patients with chronic heart failure, treated in inpatient rehabilitation clinics, who received a heart failure self-management education program. Latent change modelling was used to analyze relationships between both short-term (during inpatient rehabilitation) and intermediate-term (after six months) changes in self-reported self-management skills and both intermediate-term and long-term (after twelve months) changes in physical and mental quality of life and depressive symptoms. Short-term changes in self-reported self-management skills predicted intermediate-term changes in mental quality of life and long-term changes in physical quality of life. Intermediate-term changes in self-reported self-management skills predicted long-term changes in all outcomes. These findings support the assumption that improvements in self-management skills may foster improvements in distal outcomes.

A Comparison of Online, Video Synchronous, and Traditional Learning Modes for an Introductory Undergraduate Physics Course

NASA Astrophysics Data System (ADS)

Faulconer, E. K.; Griffith, J.; Wood, B.; Acharyya, S.; Roberts, D.

2018-05-01

While the equivalence between online and traditional classrooms has been well-researched, very little of this includes college-level introductory Physics. Only one study explored Physics at the whole-class level rather than specific course components such as a single lab or a homework platform. In this work, we compared the failure rate, grade distribution, and withdrawal rates in an introductory undergraduate Physics course across several learning modes including traditional face-to-face instruction, synchronous video instruction, and online classes. Statistically significant differences were found for student failure rates, grade distribution, and withdrawal rates but yielded small effect sizes. Post-hoc pair-wise test was run to determine differences between learning modes. Online students had a significantly lower failure rate than students who took the class via synchronous video classroom. While statistically significant differences were found for grade distributions, the pair-wise comparison yielded no statistically significance differences between learning modes when using the more conservative Bonferroni correction in post-hoc testing. Finally, in this study, student withdrawal rates were lowest for students who took the class in person (in-person classroom and synchronous video classroom) than online. Students that persist in an online introductory Physics class are more likely to achieve an A than in other modes. However, the withdrawal rate is higher from online Physics courses. Further research is warranted to better understand the reasons for higher withdrawal rates in online courses. Finding the root cause to help eliminate differences in student performance across learning modes should remain a high priority for education researchers and the education community as a whole.

Interdependent Multi-Layer Networks: Modeling and Survivability Analysis with Applications to Space-Based Networks

PubMed Central

Castet, Jean-Francois; Saleh, Joseph H.

2013-01-01

This article develops a novel approach and algorithmic tools for the modeling and survivability analysis of networks with heterogeneous nodes, and examines their application to space-based networks. Space-based networks (SBNs) allow the sharing of spacecraft on-orbit resources, such as data storage, processing, and downlink. Each spacecraft in the network can have different subsystem composition and functionality, thus resulting in node heterogeneity. Most traditional survivability analyses of networks assume node homogeneity and as a result, are not suited for the analysis of SBNs. This work proposes that heterogeneous networks can be modeled as interdependent multi-layer networks, which enables their survivability analysis. The multi-layer aspect captures the breakdown of the network according to common functionalities across the different nodes, and it allows the emergence of homogeneous sub-networks, while the interdependency aspect constrains the network to capture the physical characteristics of each node. Definitions of primitives of failure propagation are devised. Formal characterization of interdependent multi-layer networks, as well as algorithmic tools for the analysis of failure propagation across the network are developed and illustrated with space applications. The SBN applications considered consist of several networked spacecraft that can tap into each other's Command and Data Handling subsystem, in case of failure of its own, including the Telemetry, Tracking and Command, the Control Processor, and the Data Handling sub-subsystems. Various design insights are derived and discussed, and the capability to perform trade-space analysis with the proposed approach for various network characteristics is indicated. The select results here shown quantify the incremental survivability gains (with respect to a particular class of threats) of the SBN over the traditional monolith spacecraft. Failure of the connectivity between nodes is also examined, and the results highlight the importance of the reliability of the wireless links between spacecraft (nodes) to enable any survivability improvements for space-based networks. PMID:23599835

Interdependent multi-layer networks: modeling and survivability analysis with applications to space-based networks.

PubMed

Castet, Jean-Francois; Saleh, Joseph H

2013-01-01

This article develops a novel approach and algorithmic tools for the modeling and survivability analysis of networks with heterogeneous nodes, and examines their application to space-based networks. Space-based networks (SBNs) allow the sharing of spacecraft on-orbit resources, such as data storage, processing, and downlink. Each spacecraft in the network can have different subsystem composition and functionality, thus resulting in node heterogeneity. Most traditional survivability analyses of networks assume node homogeneity and as a result, are not suited for the analysis of SBNs. This work proposes that heterogeneous networks can be modeled as interdependent multi-layer networks, which enables their survivability analysis. The multi-layer aspect captures the breakdown of the network according to common functionalities across the different nodes, and it allows the emergence of homogeneous sub-networks, while the interdependency aspect constrains the network to capture the physical characteristics of each node. Definitions of primitives of failure propagation are devised. Formal characterization of interdependent multi-layer networks, as well as algorithmic tools for the analysis of failure propagation across the network are developed and illustrated with space applications. The SBN applications considered consist of several networked spacecraft that can tap into each other's Command and Data Handling subsystem, in case of failure of its own, including the Telemetry, Tracking and Command, the Control Processor, and the Data Handling sub-subsystems. Various design insights are derived and discussed, and the capability to perform trade-space analysis with the proposed approach for various network characteristics is indicated. The select results here shown quantify the incremental survivability gains (with respect to a particular class of threats) of the SBN over the traditional monolith spacecraft. Failure of the connectivity between nodes is also examined, and the results highlight the importance of the reliability of the wireless links between spacecraft (nodes) to enable any survivability improvements for space-based networks.

Bridging Empirical and Physical Approaches for Landslide Monitoring and Early Warning

NASA Technical Reports Server (NTRS)

Kirschbaum, Dalia; Peters-Lidard, Christa; Adler, Robert; Kumar, Sujay; Harrison, Ken

2011-01-01

Rainfall-triggered landslides typically occur and are evaluated at local scales, using slope-stability models to calculate coincident changes in driving and resisting forces at the hillslope level in order to anticipate slope failures. Over larger areas, detailed high resolution landslide modeling is often infeasible due to difficulties in quantifying the complex interaction between rainfall infiltration and surface materials as well as the dearth of available in situ soil and rainfall estimates and accurate landslide validation data. This presentation will discuss how satellite precipitation and surface information can be applied within a landslide hazard assessment framework to improve landslide monitoring and early warning by considering two disparate approaches to landslide hazard assessment: an empirical landslide forecasting algorithm and a physical slope-stability model. The goal of this research is to advance near real-time landslide hazard assessment and early warning at larger spatial scales. This is done by employing high resolution surface and precipitation information within a probabilistic framework to provide more physically-based grounding to empirical landslide triggering thresholds. The empirical landslide forecasting tool, running in near real-time at http://trmm.nasa.gov, considers potential landslide activity at the global scale and relies on Tropical Rainfall Measuring Mission (TRMM) precipitation data and surface products to provide a near real-time picture of where landslides may be triggered. The physical approach considers how rainfall infiltration on a hillslope affects the in situ hydro-mechanical processes that may lead to slope failure. Evaluation of these empirical and physical approaches are performed within the Land Information System (LIS), a high performance land surface model processing and data assimilation system developed within the Hydrological Sciences Branch at NASA's Goddard Space Flight Center. LIS provides the capabilities to quantify uncertainty from model inputs and calculate probabilistic estimates for slope failures. Results indicate that remote sensing data can provide many of the spatiotemporal requirements for accurate landslide monitoring and early warning; however, higher resolution precipitation inputs will help to better identify small-scale precipitation forcings that contribute to significant landslide triggering. Future missions, such as the Global Precipitation Measurement (GPM) mission will provide more frequent and extensive estimates of precipitation at the global scale, which will serve as key inputs to significantly advance the accuracy of landslide hazard assessment, particularly over larger spatial scales.

Experience, gender, and performance: Connecting high school physics experience and gender differences to introductory college physics performance

NASA Astrophysics Data System (ADS)

Tai, Robert H.

Current science educational practice is coming under heavy criticism based on the dismaying results of the Third International Mathematics and Science Study of 1998, the latest in a series of large scale surveys; and from research showing the appallingly low representation of females in science-related fields. These critical evaluations serve to draw attention to science literacy in general and lack of persistence among females in particular, two issues that relate closely to the "preparation for future study" goal held by many high school science teachers. In other words, these teachers often seek to promote future success and to prevent future failure in their students' academic careers. This thesis studies the connection between the teaching practices recommended by reformers and researchers for high school teachers, and their students' subsequent college physics performance. The teaching practices studied were: laboratory experiences, class discussion experiences, content coverage, and reliance on textbooks. This study analyzed a survey of 1500 students from 16 different lecture-format college physics courses at 14 different universities. Using hierarchical linear modeling, this study accounted for course-level variables (Calculus-based/Non-calculus course type, professor's gender, and university selectivity). This study controlled for the student's parents education, high school science/mathematics achievement, high school calculus background, and racial background. In addition, the interactions between gender and both pedagogical/curricular and course-level variables were analyzed. The results indicated that teaching fewer topics in greater depth in high school physics appeared to be helpful to college physics students. An interaction between college course type and content coverage showed that students in Calculus-based physics reaped even greater benefits from a depth-oriented curriculum. Also students with fewer labs per month in high school physics appeared to perform better in college physics than did students with many more labs per month. The only significant interaction was between gender and Calculus-based/Non-calculus college course type. Females appeared to do better on average than their males counterparts in Non-calculus physics, but this trend is clearly reversed for Calculus-based physics. This is a disturbing result for educators who have worked to promote persistence among women in engineering and science research. Recommendations are included for high school physics teachers, students and their parents, and college physics instructors.

Patients' experiences of physical limitations in daily life activities when suffering from chronic heart failure; a phenomenographic analysis.

PubMed

Pihl, Emma; Fridlund, Bengt; Mårtensson, Jan

2011-03-01

The aim of the study was to describe how patients suffering from chronic heart failure conceived their physical limitations in daily life activities. An explorative and qualitative design with a phenomenographic approach was chosen, a total of 15 patients were interviewed. The findings indicate that participants perceived a variety of structural aspects pertaining to physical limitations in activities of daily life which resulted in four referential aspects. Need of finding practical solutions in daily life focused on how life had to be changed and other ways of performing activities of daily life had to be invented. Having realistic expectations about the future was characterised by belief that the future itself would be marked by change in physical functioning, but an incentive to maintain functions and activities ensured good quality of or even increased capacity in daily life. Not believing in one's own ability included the perception of having no opportunity to improve ability to perform activities of daily life. There were perceptions of undesired passivity, undefined fear of straining themselves or performing activities that could endanger their health in addition to uncertainty about the future. In Losing one's social role in daily life, participants described losing their social network and their position in society and family because of limited physical capacity. A lack of important issues, mental and physical, occurred when physical capacity was lost. In conclusion, patients suffering from chronic heart failure found new solutions to manage activities in daily life, including willingness to change focus and identify other ways of doing important things. Patients had an incentive to maintain functions and activities to ensure a good quality of and strengthen their physical capacity in daily life. Inability to trust in their physical capacity in combination with experienced limitations in daily life prevented patients from attempting to increase activities. © 2010 The Authors. Scandinavian Journal of Caring Sciences © 2010 Nordic College of Caring Science.

A Void Growth Failure Criterion Applied to Dynamically and Statically Loaded Thin Rings.

DTIC Science & Technology

1980-06-01

the physical evidences, several other investigators (Berg, 1969, Nagpal , et al., 1972) working on the continuum aspect of failure, considered plastic...by the Growth of Holes", J. of Applied Mechanics, Vol. 35, 1968, p. 363. 23.) Nagpal , V., Mcclintock, F. A., Berg, C. A., and Subudhi, M., "Traction

Precursory changes in seismic velocity for the spectrum of earthquake failure modes

PubMed Central

Scuderi, M.M.; Marone, C.; Tinti, E.; Di Stefano, G.; Collettini, C.

2016-01-01

Temporal changes in seismic velocity during the earthquake cycle have the potential to illuminate physical processes associated with fault weakening and connections between the range of fault slip behaviors including slow earthquakes, tremor and low frequency earthquakes1. Laboratory and theoretical studies predict changes in seismic velocity prior to earthquake failure2, however tectonic faults fail in a spectrum of modes and little is known about precursors for those modes3. Here we show that precursory changes of wave speed occur in laboratory faults for the complete spectrum of failure modes observed for tectonic faults. We systematically altered the stiffness of the loading system to reproduce the transition from slow to fast stick-slip and monitored ultrasonic wave speed during frictional sliding. We find systematic variations of elastic properties during the seismic cycle for both slow and fast earthquakes indicating similar physical mechanisms during rupture nucleation. Our data show that accelerated fault creep causes reduction of seismic velocity and elastic moduli during the preparatory phase preceding failure, which suggests that real time monitoring of active faults may be a means to detect earthquake precursors. PMID:27597879

Magnetic Resonance Imaging Predictors of Failure in the Nonoperative Management of Ulnar Collateral Ligament Injuries in Professional Baseball Pitchers.

PubMed

Frangiamore, Salvatore J; Lynch, T Sean; Vaughn, Michael D; Soloff, Lonnie; Forney, Michael; Styron, Joseph F; Schickendantz, Mark S

2017-07-01

A medial ulnar collateral ligament (UCL) injury of the elbow is an increasingly common injury in professional baseball pitchers. Predictors of success and failure are not well defined for the nonoperative management of these injuries. To evaluate the efficacy of objective measures to predict failure of the nonoperative management of UCL injuries. Case-control study; Level of evidence, 3. Thirty-two professional pitchers (82%) met inclusion criteria and underwent an initial trial of nonoperative treatment for UCL tears based on clinical and radiological findings. Age, preseason physical examination results, magnetic resonance imaging (MRI) characteristics, and performance metrics were analyzed for these pitchers. Successful nonoperative management was defined as a return to the same level of play or higher for >1 year. Failure was defined as recurrent pain or weakness requiring a surgical intervention after a minimum of 3 months' rest when attempting a return to a throwing rehabilitation program. Thirty-two pitchers (mean age, 22.3 years) who underwent initial nonoperative treatment of UCL injuries were evaluated. Thirty-four percent (11/32) failed and required subsequent ligament reconstruction. Sixty-six percent (21/32) successfully returned to the same level of play for 1 year without a surgical intervention. There was no significant difference seen in physical examination findings or performance metrics between these patients. When comparing MRI findings between the groups, 82% (9/11) ( P < .001) who failed nonoperative management had distal tears, and 81% (17/21) who did not fail had proximal tears ( P < .001). When adjusting for age, location, and evidence of chronic changes on MRI, the likelihood of failing nonoperative management was 12.40 times greater ( P = .020) with a distal tear. No other variable alone or in combination reached significance. When combining the parameters of a high-grade tear and distal location, 88% (7/8) failed nonoperative management. In professional pitchers, distal UCL tears showed significantly higher odds of failure with nonoperative management compared with proximal tears. Thus, tear location should be considered when deciding between operative and nonoperative management.

Orlistat-induced fulminant hepatic failure.

PubMed

Sall, D; Wang, J; Rashkin, M; Welch, M; Droege, C; Schauer, D

2014-12-01

Orlistat was approved by the Food and Drug Administration in 1998 and has been shown to be superior to placebo in achieving weight loss. It is generally well tolerated. However, severe liver injury has been reported. We present a case of hepatic failure in a patient taking orlistat. A 54-year-old African-American woman with hypertension presented with hepatic failure. She had noticed increasing fatigue, jaundice and confusion. She used alcohol sparingly and denied tobacco or illicit drug use, but had been taking over-the-counter orlistat for the past two months. Physical examination revealed scleral icterus, jaundice, asterixis and slow speech. Laboratory testing showed markedly abnormal liver function tests with coagulopathy. Acute viral and autoimmune serologies were negative, as was toxicology screen. Liver biopsy showed necrotic hepatic parenchyma likely secondary to drug toxicity. Based upon her clinical presentation and time course, the pattern of liver injury seen on liver biopsy and lack of an alternative plausible explanation, her liver failure was most likely associated with orlistat use. She continued to deteriorate and ultimately underwent orthotopic liver transplantation. Fourteen cases of severe liver injury associated with orlistat use have been reported, four of which are detailed in the literature. This is the second published case of liver failure associated with over-the-counter orlistat usage. Clinicians should be aware of the growing number of cases associating liver injury and orlistat use and carefully monitor their patients on this medication for signs of hepatic dysfunction. © 2014 The Authors. Clinical Obesity © 2014 World Obesity.

A thermomechanical constitutive model for cemented granular materials with quantifiable internal variables. Part II - Validation and localization analysis

NASA Astrophysics Data System (ADS)

Das, Arghya; Tengattini, Alessandro; Nguyen, Giang D.; Viggiani, Gioacchino; Hall, Stephen A.; Einav, Itai

2014-10-01

We study the mechanical failure of cemented granular materials (e.g., sandstones) using a constitutive model based on breakage mechanics for grain crushing and damage mechanics for cement fracture. The theoretical aspects of this model are presented in Part I: Tengattini et al. (2014), A thermomechanical constitutive model for cemented granular materials with quantifiable internal variables, Part I - Theory (Journal of the Mechanics and Physics of Solids, 10.1016/j.jmps.2014.05.021). In this Part II we investigate the constitutive and structural responses of cemented granular materials through analyses of Boundary Value Problems (BVPs). The multiple failure mechanisms captured by the proposed model enable the behavior of cemented granular rocks to be well reproduced for a wide range of confining pressures. Furthermore, through comparison of the model predictions and experimental data, the micromechanical basis of the model provides improved understanding of failure mechanisms of cemented granular materials. In particular, we show that grain crushing is the predominant inelastic deformation mechanism under high pressures while cement failure is the relevant mechanism at low pressures. Over an intermediate pressure regime a mixed mode of failure mechanisms is observed. Furthermore, the micromechanical roots of the model allow the effects on localized deformation modes of various initial microstructures to be studied. The results obtained from both the constitutive responses and BVP solutions indicate that the proposed approach and model provide a promising basis for future theoretical studies on cemented granular materials.

Reliability training

NASA Technical Reports Server (NTRS)

Lalli, Vincent R. (Editor); Malec, Henry A. (Editor); Dillard, Richard B.; Wong, Kam L.; Barber, Frank J.; Barina, Frank J.

1992-01-01

Discussed here is failure physics, the study of how products, hardware, software, and systems fail and what can be done about it. The intent is to impart useful information, to extend the limits of production capability, and to assist in achieving low cost reliable products. A review of reliability for the years 1940 to 2000 is given. Next, a review of mathematics is given as well as a description of what elements contribute to product failures. Basic reliability theory and the disciplines that allow us to control and eliminate failures are elucidated.

Property Values Associated with the Failure of Individual Links in a System with Multiple Weak and Strong Links.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helton, Jon C.; Brooks, Dusty Marie; Sallaberry, Cedric Jean-Marie.

Representations are developed and illustrated for the distribution of link property values at the time of link failure in the presence of aleatory uncertainty in link properties. The following topics are considered: (i) defining properties for weak links and strong links, (ii) cumulative distribution functions (CDFs) for link failure time, (iii) integral-based derivation of CDFs for link property at time of link failure, (iv) sampling-based approximation of CDFs for link property at time of link failure, (v) verification of integral-based and sampling-based determinations of CDFs for link property at time of link failure, (vi) distributions of link properties conditional onmore » time of link failure, and (vii) equivalence of two different integral-based derivations of CDFs for link property at time of link failure.« less

Impact of a comprehensive supportive care team on management of hopelessly ill patients with multiple organ failure.

PubMed

Field, B E; Devich, L E; Carlson, R W

1989-08-01

We developed a supportive care team for hopelessly ill patients in an urban emergency/trauma hospital. The team includes a clinical nurse specialist and a faculty physician as well as a chaplain and social worker. The supportive care team provides an alternative to intensive care or conventional ward management of hopelessly ill patients and concentrates on the physical and psychosocial comfort needs of patients and their families. We describe our experience with 20 hopelessly ill patients with multiple organ failure vs a similar group treated before the development of the supportive care team. Although there was no difference in mortality (100 percent), the length of stay in the medical ICU for patients with multiple organ failure decreased by 12 days to 6 days. Additionally, there were 50 percent fewer therapeutic interventions provided by the supportive care team vs intensive care or conventional ward treatment of multiple organ failure patients. We describe the methods that the supportive care team uses in an attempt to meet the physical and psychosocial comfort needs of hopelessly ill multiple organ failure patients and their families. This multidisciplinary approach to the care of the hopelessly ill may have applications in other institutions facing the ethical, medical, and administrative challenges raised by these patients.

Enhanced Schapery Theory Software Development for Modeling Failure of Fiber-Reinforced Laminates

NASA Technical Reports Server (NTRS)

Pineda, Evan J.; Waas, Anthony M.

2013-01-01

Progressive damage and failure analysis (PDFA) tools are needed to predict the nonlinear response of advanced fiber-reinforced composite structures. Predictive tools should incorporate the underlying physics of the damage and failure mechanisms observed in the composite, and should utilize as few input parameters as possible. The purpose of the Enhanced Schapery Theory (EST) was to create a PDFA tool that operates in conjunction with a commercially available finite element (FE) code (Abaqus). The tool captures the physics of the damage and failure mechanisms that result in the nonlinear behavior of the material, and the failure methodology employed yields numerical results that are relatively insensitive to changes in the FE mesh. The EST code is written in Fortran and compiled into a static library that is linked to Abaqus. A Fortran Abaqus UMAT material subroutine is used to facilitate the communication between Abaqus and EST. A clear distinction between damage and failure is imposed. Damage mechanisms result in pre-peak nonlinearity in the stress strain curve. Four internal state variables (ISVs) are utilized to control the damage and failure degradation. All damage is said to result from matrix microdamage, and a single ISV marks the micro-damage evolution as it is used to degrade the transverse and shear moduli of the lamina using a set of experimentally obtainable matrix microdamage functions. Three separate failure ISVs are used to incorporate failure due to fiber breakage, mode I matrix cracking, and mode II matrix cracking. Failure initiation is determined using a failure criterion, and the evolution of these ISVs is controlled by a set of traction-separation laws. The traction separation laws are postulated such that the area under the curves is equal to the fracture toughness of the material associated with the corresponding failure mechanism. A characteristic finite element length is used to transform the traction-separation laws into stress-strain laws. The ISV evolution equations are derived in a thermodynamically consistent manner by invoking the stationary principle on the total work of the system with respect to each ISV. A novel feature is the inclusion of both pre-peak damage and appropriately scaled, post-peak strain softening failure. Also, the characteristic elements used in the failure degradation scheme are calculated using the element nodal coordinates, rather than simply the square root of the area of the element.

Development of friction and wear full-scale testing for TKR prostheses with reliable low cost apparatus

NASA Astrophysics Data System (ADS)

Suwandi, Agri; Soemardi, Tresna P.; Kiswanto, Gandjar; Kusumaningsih, Widjajalaksmi; I. Gusti Agung I. G., W.

2018-02-01

Prostheses products must undergo simulation and physical testing, before clinical testing. Finite element method is a preliminary simulation for in vivo test. The method visualizes the magnitude of the compressive force and the critical location of the Total Knee Replacement (TKR) prostheses design. In vitro testing is classified as physical testing for prostheses product. The test is conducted to evaluate the potential failure of the product and the characteristics of the prostheses TKR material. Friction and wear testing are part of the in vivo test. Motion of knee joints, which results in the phenomena of extension and deflection in the femoral and tibia insert, is represented by friction and wear testing. Friction and wear tests aim to obtain an approximate lifetime in normal and extreme load patterns as characterized by the shape of the friction surface area. The lifetime estimation requires friction and wear full-scale testing equipments for TKR prostheses products. These are necessary in obtaining initial data on potential product failures and characterizing of the material based on the ASTM F2724-08 standards. Based on the testing result and statistical analysis data, the average wear rate value per year is 2.19 × 10-3 mg/MC, with a 10 % safety limit of volume and 14,400 cycles times, for 15 hours moving nonstop then the prediction of wear life of the component tibia insert is ± 10 years.

Experimental analysis of computer system dependability

NASA Technical Reports Server (NTRS)

Iyer, Ravishankar, K.; Tang, Dong

1993-01-01

This paper reviews an area which has evolved over the past 15 years: experimental analysis of computer system dependability. Methodologies and advances are discussed for three basic approaches used in the area: simulated fault injection, physical fault injection, and measurement-based analysis. The three approaches are suited, respectively, to dependability evaluation in the three phases of a system's life: design phase, prototype phase, and operational phase. Before the discussion of these phases, several statistical techniques used in the area are introduced. For each phase, a classification of research methods or study topics is outlined, followed by discussion of these methods or topics as well as representative studies. The statistical techniques introduced include the estimation of parameters and confidence intervals, probability distribution characterization, and several multivariate analysis methods. Importance sampling, a statistical technique used to accelerate Monte Carlo simulation, is also introduced. The discussion of simulated fault injection covers electrical-level, logic-level, and function-level fault injection methods as well as representative simulation environments such as FOCUS and DEPEND. The discussion of physical fault injection covers hardware, software, and radiation fault injection methods as well as several software and hybrid tools including FIAT, FERARI, HYBRID, and FINE. The discussion of measurement-based analysis covers measurement and data processing techniques, basic error characterization, dependency analysis, Markov reward modeling, software-dependability, and fault diagnosis. The discussion involves several important issues studies in the area, including fault models, fast simulation techniques, workload/failure dependency, correlated failures, and software fault tolerance.

Theory and Modeling of Liquid Explosive Detonation

NASA Astrophysics Data System (ADS)

Tarver, Craig M.; Urtiew, Paul A.

2010-10-01

The current understanding of the detonation reaction zones of liquid explosives is discussed in this article. The physical and chemical processes that precede and follow exothermic chemical reaction within the detonation reaction zone are discussed within the framework of the nonequilibrium Zeldovich-von Neumann-Doring (NEZND) theory of self-sustaining detonation. Nonequilibrium chemical and physical processes cause finite time duration induction zones before exothermic chemical energy release occurs. This separation between the leading shock wave front and the chemical energy release needed to sustain it results in shock wave amplification and the subsequent formation of complex three-dimensional cellular structures in all liquid detonation waves. To develop a practical Zeldovich-von Neumann-Doring (ZND) reactive flow model for liquid detonation, experimental data on reaction zone structure, confined failure diameter, unconfined failure diameter, and failure wave velocity in the Dremin-Trofimov test for detonating nitromethane are calculated using the ignition and growth reactive flow model.

Physics of Earthquake Disaster: From Crustal Rupture to Building Collapse

NASA Astrophysics Data System (ADS)

Uenishi, Koji

2018-05-01

Earthquakes of relatively greater magnitude may cause serious, sometimes unexpected failures of natural and human-made structures, either on the surface, underground, or even at sea. In this review, by treating several examples of extraordinary earthquake-related failures that range from the collapse of every second building in a commune to the initiation of spontaneous crustal rupture at depth, we consider the physical background behind the apparently abnormal earthquake disaster. Simple but rigorous dynamic analyses reveal that such seemingly unusual failures actually occurred for obvious reasons, which may remain unrecognized in part because in conventional seismic analyses only kinematic aspects of the effects of lower-frequency seismic waves below 1 Hz are normally considered. Instead of kinematics, some dynamic approach that takes into account the influence of higher-frequency components of waves over 1 Hz will be needed to anticipate and explain such extraordinary phenomena and mitigate the impact of earthquake disaster in the future.

Application of Failure Mode and Effects Analysis to Intraoperative Radiation Therapy Using Mobile Electron Linear Accelerators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ciocca, Mario, E-mail: mario.ciocca@cnao.it; Cantone, Marie-Claire; Veronese, Ivan

2012-02-01

Purpose: Failure mode and effects analysis (FMEA) represents a prospective approach for risk assessment. A multidisciplinary working group of the Italian Association for Medical Physics applied FMEA to electron beam intraoperative radiation therapy (IORT) delivered using mobile linear accelerators, aiming at preventing accidental exposures to the patient. Methods and Materials: FMEA was applied to the IORT process, for the stages of the treatment delivery and verification, and consisted of three steps: 1) identification of the involved subprocesses; 2) identification and ranking of the potential failure modes, together with their causes and effects, using the risk probability number (RPN) scoring system,more » based on the product of three parameters (severity, frequency of occurrence and detectability, each ranging from 1 to 10); 3) identification of additional safety measures to be proposed for process quality and safety improvement. RPN upper threshold for little concern of risk was set at 125. Results: Twenty-four subprocesses were identified. Ten potential failure modes were found and scored, in terms of RPN, in the range of 42-216. The most critical failure modes consisted of internal shield misalignment, wrong Monitor Unit calculation and incorrect data entry at treatment console. Potential causes of failure included shield displacement, human errors, such as underestimation of CTV extension, mainly because of lack of adequate training and time pressures, failure in the communication between operators, and machine malfunctioning. The main effects of failure were represented by CTV underdose, wrong dose distribution and/or delivery, unintended normal tissue irradiation. As additional safety measures, the utilization of a dedicated staff for IORT, double-checking of MU calculation and data entry and finally implementation of in vivo dosimetry were suggested. Conclusions: FMEA appeared as a useful tool for prospective evaluation of patient safety in radiotherapy. The application of this method to IORT lead to identify three safety measures for risk mitigation.« less

[Evaluation of a chronic fatigue in patients with moderate-to-severe chronic heart failure].

PubMed

Jasiukeviciene, Lina; Vasiliauskas, Donatas; Kavoliūniene, Ausra; Marcinkeviciene, Jolanta; Grybauskiene, Regina; Grizas, Vytautas; Tumyniene, Vida

2008-01-01

To evaluate the chronic fatigue and its relation to the function of hypothalamus-pituitary-adrenal axis in patients with New York Heart Association (NYHA) functional class III-IV chronic heart failure. A total of 170 patients with NYHA functional class III-IV chronic heart failure completed MFI-20L, DUFS, and DEFS questionnaires assessing chronic fatigue and underwent echocardiography. Blood cortisol concentration was assessed at 8:00 am and 3:00 pm, and plasma N-terminal brain natriuretic pro-peptide (NT-proBNP) concentration was measured at 8:00 am. Neurohumoral investigations were repeated before cardiopulmonary exercise test and after it. The results of all questionnaires showed that 100% of patients with NYHA functional class III-IV heart failure complained of chronic fatigue. The level of overall fatigue was 54.5+/-31.5 points; physical fatigue - 56.8+/-24.6 points. Blood cortisol concentration at 8:00 am was normal (410.1+/-175.1 mmol/L) in majority of patients. Decreased concentration was only in four patients (122.4+/-15.5 mmol/L); one of these patients underwent heart transplantation. In the afternoon, blood cortisol concentration was insufficiently decreased (355.6+/-160.3 mmol/L); reaction to a physical stress was attenuated (Delta 92.9 mmol/L). Plasma NT-proBNP concentration was 2188.9+/-1852.2 pg/L; reaction to a physical stress was diminished (Delta 490.3 pg/L). All patients with NYHA class III-IV heart failure complained of daily chronic fatigue. Insufficiently decreased blood cortisol concentration in the afternoon showed that in the presence of chronic fatigue in long-term cardiovascular organic disease, disorder of a hypothalamus-pituitary-adrenal axis is involved.

Physical Properties of Granulates Used in Analogue Experiments of Caprock Failure and Sediment Remobilisation

NASA Astrophysics Data System (ADS)

Kukowski, N.; Warsitzka, M.; May, F.

2014-12-01

Geological systems consisting of a porous reservoir and a low-permeable caprock are prone to hydraulic fracturing, if pore pressure rises to the effective stress. Under certain conditions, hydraulic fracturing is associated with sediment remobilisation, e.g. sand injections or pipes, leading to reduced seal capacity of the caprock. In dynamically scaled analogue experiments using granular materials and air pressure, we intent to investigate strain patterns and deformation mechanisms during caprock failure and fluidisation of shallow over-pressured reservoirs. The aim of this study is to improve the understanding of leakage potential of a sealing formation and the fluidisation potential of a reservoir formation depending on rock properties and effective stress. For reliable interpretation of analogue experiments, physical properties of analogue materials, e.g. frictional strength, cohesion, density, permeability etc., have to be correctly scaled according to those of their natural equivalents. The simulation of caprock requires that the analogue material possess a low permeability and is capable to shear failure and tensional failure. In contrast, materials representing the reservoir have to possess high porosity and low shear strength. In order to find suitable analogue materials, we measured the stress-strain behaviour and the permeability of over 25 different types of natural and artificial granular materials, e.g. glass powder, siliceous microspheres, diatomite powder, loess, or plastic granulate. Here, we present data of frictional parameters, compressibility and permeability of these granular materials characterized as a function of sphericity, grain size, and density. The repertoire of different types of granulates facilitates the adjustment of accurate mechanical properties in the analogue experiments. Furthermore, conditions during seal failure and fluidisation can be examined depending on the wide range of varying physical properties.

Consensus statement: Palliative and supportive care in advanced heart failure.

PubMed

Goodlin, Sarah J; Hauptman, Paul J; Arnold, Robert; Grady, Kathleen; Hershberger, Ray E; Kutner, Jean; Masoudi, Frederick; Spertus, John; Dracup, Kathleen; Cleary, James F; Medak, Ruth; Crispell, Kathy; Piña, Ileana; Stuart, Brad; Whitney, Christy; Rector, Thomas; Teno, Joan; Renlund, Dale G

2004-06-01

A consensus conference was convened to define the current state and important gaps in knowledge and needed research on "Palliative and Supportive Care in Advanced Heart Failure." Evidence was drawn from expert opinion and from extensive review of the medical literature, evidence-based guidelines, and reviews. The conference identified gaps in current knowledge, practice, and research relating to prognostication, symptom management, and supportive care for advanced heart failure (HF). Specific conclusions include: (1) although supportive care should be integrated throughout treatment of patients with advanced HF, data are needed to understand how to best decrease physical and psychosocial burdens of advanced HF and to meet patient and family needs; (2) prognostication in advanced HF is difficult and data are needed to understand which patients will benefit from which interventions and how best to counsel patients with advanced HF; (3) research is needed to identify which interventions improve quality of life and best achieve the outcomes desired by patients and family members; (4) care should be coordinated between sites of care, and barriers to evidence-based practice must be addressed programmatically; and (5) more research is needed to identify the content and technique of communicating prognosis and treatment options with patients with advanced HF; physicians caring for patients with advanced HF must develop skills to better integrate the patient's preferences into the goals of care.

A Prospective, Randomized Trial of Routine Duplex Ultrasound Surveillance on Arteriovenous Fistula Maturation.

PubMed

Han, Ahram; Min, Seung-Kee; Kim, Mi-Sook; Joo, Kwon Wook; Kim, Jungsun; Ha, Jongwon; Lee, Joongyub; Min, Sang-Il

2016-10-07

Use of arteriovenous fistulas, the most preferred type of access for hemodialysis, is limited by their high maturation failure rate. The aim of this study was to assess whether aggressive surveillance with routine duplex ultrasound and intervention can decrease the maturation failure rate of arteriovenous fistulas. We conducted a single-center, parallel-group, randomized, controlled trial of patients undergoing autogenous arteriovenous fistula. Patients were randomly assigned (1:1) to either the routine duplex or selective duplex group. In the routine duplex group, duplex ultrasound and physical examination were performed 2, 4, and 8 weeks postoperatively. In the selective duplex group, duplex examination was performed only when physical examination detected an abnormality. The primary end point was the maturation failure rate 8 weeks after fistula creation. Maturation failure was defined as the inability to achieve clinical maturation ( i.e. , a successful first use) and failure to achieve sonographic maturation (fistula flow >500 ml/min and diameter >6 mm) within 8 weeks. Between June 14, 2012, and June 25, 2014, 150 patients were enrolled (75 patients in each group), and 118 of those were included in the final analysis. The maturation failure rate was lower in the routine duplex group (8 of 59; 13.6%) than in the selective duplex group (15 of 59; 25.4%), but the difference was not statistically significant (odds ratio, 0.46; 95% confidence interval, 0.18 to 1.19; P =0.10). Factors associated with maturation failure were women (odds ratio, 3.84; 95% confidence interval, 1.05 to 14.06; P =0.04), coronary artery disease (odds ratio, 6.36; 95% confidence interval, 1.62 to 24.95; P <0.01), diabetes (odds ratio, 6.10; 95% confidence interval, 1.76 to 21.19; P <0.01), and the preoperative cephalic vein diameter (odds ratio, 0.30; 95% confidence interval, 0.13 to 0.71; P <0.01). Postoperative routine duplex surveillance failed to prove superiority compared with selective duplex after physical examination for reducing arteriovenous fistula maturation failure. However, the wide 95% confidence interval for the effect of intervention precludes a firm conclusion that routine duplex surveillance was not beneficial. Copyright © 2016 by the American Society of Nephrology.

A systems approach to solder joint fatigue in spacecraft electronic packaging

NASA Technical Reports Server (NTRS)

Ross, R. G., Jr.

1991-01-01

Differential expansion induced fatigue resulting from temperature cycling is a leading cause of solder joint failures in spacecraft. Achieving high reliability flight hardware requires that each element of the fatigue issue be addressed carefully. This includes defining the complete thermal-cycle environment to be experienced by the hardware, developing electronic packaging concepts that are consistent with the defined environments, and validating the completed designs with a thorough qualification and acceptance test program. This paper describes a useful systems approach to solder fatigue based principally on the fundamental log-strain versus log-cycles-to-failure behavior of fatigue. This fundamental behavior has been useful to integrate diverse ground test and flight operational thermal-cycle environments into a unified electronics design approach. Each element of the approach reflects both the mechanism physics that control solder fatigue, as well as the practical realities of the hardware build, test, delivery, and application cycle.

Application of Video Image Correlation Techniques to the Space Shuttle External Tank Foam Materials

NASA Technical Reports Server (NTRS)

Hilburger, Mark W.; Nemeth, Michael P.

2005-01-01

Results that illustrate the use of a video-image-correlation-based displacement and strain measurement system to assess the effects of material nonuniformities on the behavior of the sprayed-on foam insulation (SOFI) used for the thermal protection system on the Space Shuttle External Tank are presented. Standard structural verification specimens for the SOFI material with and without cracks and subjected to mechanical or thermal loading conditions were tested. Measured full-field displacements and strains are presented for selected loading conditions to illustrate the behavior of the foam and the viability of the measurement technology. The results indicate that significant strain localization can occur in the foam because of material nonuniformities. In particular, elongated cells in the foam can interact with other geometric or material discontinuities in the foam and develop large-magnitude localized strain concentrations that likely initiate failures. Furthermore, some of the results suggest that continuum mechanics and linear elastic fracture mechanics might not adequately represent the physical behavior of the foam, and failure predictions based on homogeneous linear material models are likely to be inadequate.

Application of Video Image Correlation Techniques to the Space Shuttle External Tank Foam Materials

NASA Technical Reports Server (NTRS)

Hilburger, Mark W.; Nemeth, Michael P.

2006-01-01

Results that illustrate the use of a video-image-correlation-based displacement and strain measurement system to assess the effects of material nonuniformities on the behavior of the sprayed-on foam insulation (SOFI) used for the thermal protection system on the Space Shuttle External Tank are presented. Standard structural verification specimens for the SOFI material with and without cracks and subjected to mechanical or thermal loading conditions were tested. Measured full-field displacements and strains are presented for selected loading conditions to illustrate the behavior of the foam and the viability of the measurement technology. The results indicate that significant strain localization can occur in the foam because of material nonuniformities. In particular, elongated cells in the foam can interact with other geometric or material discontinuities in the foam and develop large-magnitude localized strain concentrations that likely initiate failures. Furthermore, some of the results suggest that continuum mechanics and linear elastic fracture mechanics might not adequately represent the physical behavior of the foam, and failure predictions based on homogeneous linear material models are likely to be inadequate.

A late and failure of airbag deployment case study for drivers of passenger cars in rear-end collisions

NASA Astrophysics Data System (ADS)

Toganel, George-Radu; Ovidiu Soica, Adrian

2017-10-01

The presented study was directed at two types of airbag miss-deployments: late deployment and non-deployment. Late deployment can be a product of override or underride road traffic accidents. Non-deployment can be a product of technical failure or trigger algorithm’s inability to correctly assume the state of the accident to happen. In order to analyse the phenomena through physical tests, a specialized test device was used for a series of 8 non-deployment tests and a series of 4 airbag firing tests, totalling 12 tests. Acceleration based data was recorded and analysed for the movement of the device part simulating the driver head. High speed video recording was used to analyse the mechanics of airbag deployment and correlate with the acceleration based data. It has been determined, in the limitations of the laboratory testing environment, a significant variation of the time frame for the airbag deployments, despite using similar testing conditions and identical tested products. Also, the initial time frame for airbag deployment delay was overshadowed by other factors such as time to impact.

Endurance Enhancement and High Speed Set/Reset of 50 nm Generation HfO2 Based Resistive Random Access Memory Cell by Intelligent Set/Reset Pulse Shape Optimization and Verify Scheme

NASA Astrophysics Data System (ADS)

Higuchi, Kazuhide; Miyaji, Kousuke; Johguchi, Koh; Takeuchi, Ken

2012-02-01

This paper proposes a verify-programming method for the resistive random access memory (ReRAM) cell which achieves a 50-times higher endurance and a fast set and reset compared with the conventional method. The proposed verify-programming method uses the incremental pulse width with turnback (IPWWT) for the reset and the incremental voltage with turnback (IVWT) for the set. With the combination of IPWWT reset and IVWT set, the endurance-cycle increases from 48 ×103 to 2444 ×103 cycles. Furthermore, the measured data retention-time after 20 ×103 set/reset cycles is estimated to be 10 years. Additionally, the filamentary based physical model is proposed to explain the set/reset failure mechanism with various set/reset pulse shapes. The reset pulse width and set voltage correspond to the width and length of the conductive-filament, respectively. Consequently, since the proposed IPWWT and IVWT recover set and reset failures of ReRAM cells, the endurance-cycles are improved.

Methodology for balancing design and process tradeoffs for deep-subwavelength technologies

NASA Astrophysics Data System (ADS)

Graur, Ioana; Wagner, Tina; Ryan, Deborah; Chidambarrao, Dureseti; Kumaraswamy, Anand; Bickford, Jeanne; Styduhar, Mark; Wang, Lee

2011-04-01

For process development of deep-subwavelength technologies, it has become accepted practice to use model-based simulation to predict systematic and parametric failures. Increasingly, these techniques are being used by designers to ensure layout manufacturability, as an alternative to, or complement to, restrictive design rules. The benefit of model-based simulation tools in the design environment is that manufacturability problems are addressed in a design-aware way by making appropriate trade-offs, e.g., between overall chip density and manufacturing cost and yield. The paper shows how library elements and the full ASIC design flow benefit from eliminating hot spots and improving design robustness early in the design cycle. It demonstrates a path to yield optimization and first time right designs implemented in leading edge technologies. The approach described herein identifies those areas in the design that could benefit from being fixed early, leading to design updates and avoiding later design churn by careful selection of design sensitivities. This paper shows how to achieve this goal by using simulation tools incorporating various models from sparse to rigorously physical, pattern detection and pattern matching, checking and validating failure thresholds.

Practical implementation of the double linear damage rule and damage curve approach for treating cumulative fatigue damage

NASA Technical Reports Server (NTRS)

Manson, S. S.; Halford, G. R.

1981-01-01

Simple procedures are given for treating cumulative fatigue damage under complex loading history using either the damage curve concept or the double linear damage rule. A single equation is given for use with the damage curve approach; each loading event providing a fraction of damage until failure is presumed to occur when the damage sum becomes unity. For the double linear damage rule, analytical expressions are given for determining the two phases of life. The procedure comprises two steps, each similar to the conventional application of the commonly used linear damage rule. Once the sum of cycle ratios based on Phase I lives reaches unity, Phase I is presumed complete, and further loadings are summed as cycle ratios based on Phase II lives. When the Phase II sum attains unity, failure is presumed to occur. It is noted that no physical properties or material constants other than those normally used in a conventional linear damage rule analysis are required for application of either of the two cumulative damage methods described. Illustrations and comparisons are discussed for both methods.

Numerical modelling of glacial lake outburst floods using physically based dam-breach models

NASA Astrophysics Data System (ADS)

Westoby, M. J.; Brasington, J.; Glasser, N. F.; Hambrey, M. J.; Reynolds, J. M.; Hassan, M. A. A. M.; Lowe, A.

2015-03-01

The instability of moraine-dammed proglacial lakes creates the potential for catastrophic glacial lake outburst floods (GLOFs) in high-mountain regions. In this research, we use a unique combination of numerical dam-breach and two-dimensional hydrodynamic modelling, employed within a generalised likelihood uncertainty estimation (GLUE) framework, to quantify predictive uncertainty in model outputs associated with a reconstruction of the Dig Tsho failure in Nepal. Monte Carlo analysis was used to sample the model parameter space, and morphological descriptors of the moraine breach were used to evaluate model performance. Multiple breach scenarios were produced by differing parameter ensembles associated with a range of breach initiation mechanisms, including overtopping waves and mechanical failure of the dam face. The material roughness coefficient was found to exert a dominant influence over model performance. The downstream routing of scenario-specific breach hydrographs revealed significant differences in the timing and extent of inundation. A GLUE-based methodology for constructing probabilistic maps of inundation extent, flow depth, and hazard is presented and provides a useful tool for communicating uncertainty in GLOF hazard assessment.

Global Warming and Ice Ages: I. Prospects For Physics Based Modulation of Global Change

DOE R&D Accomplishments Database

Teller, E.; Wood, L.; Hyde, R.

1996-08-15

It has been suggested that large-scale climate changes, mostly due to atmospheric injection of greenhouse gases connected with fossil-fired energy production, should be forestalled by internationally-agreed reductions in, e.g., electricity generation. The potential economic impacts of such limitations are obviously large: greater than or equal to $10{sup 11}/year. We propose that for far smaller - less than 1% - the mean thermal effects of greenhouse gases may be obviated in any of several distinct ways, some of them novel. These suggestions are all based on scatterers that prevent a small fraction of solar radiation from reaching all or part of the Earth. We propose research directed to quite near-term realization of one or more of these inexpensive approaches to cancel the effects of the greenhouse gas injection. While the magnitude of the climatic impact of greenhouse gases is currently uncertain, the prospect of severe failure of the climate, for instance at the onset of the next Ice Age, is undeniable. The proposals in this paper may lead to quite practical methods to reduce or eliminate all climate failures.

Strategy to recognize and initiate treatment of chronic heart failure in primary care (STRETCH): a cluster randomized trial.

PubMed

van Riet, Evelien E S; Hoes, Arno W; Limburg, Alexander; van der Hoeven, Henk; Landman, Marcel A J; Rutten, Frans H

2014-01-08

Most patients with heart failure are diagnosed and managed in primary care, however, underdiagnosis and undertreatment are common. We assessed whether implementation of a diagnostic-therapeutic strategy improves functionality, health-related quality of life, and uptake of heart failure medication in primary care. A selective screening study followed by a single-blind cluster randomized trial in primary care. The study population consists of patients aged 65 years or over who presented themselves to the general practitioner in the previous 12 months with shortness of breath on exertion. Patients already known with established heart failure, confirmed by echocardiography, are excluded. Diagnostic investigations include history taking, physical examination, electrocardiography, and serum N-terminal pro B-type natriuretic peptide levels. Only participants with an abnormal electrocardiogram or an N-terminal pro B-type natriuretic peptide level exceeding the exclusionary cutpoint for non-acute onset heart failure (> 15 pmol/L (≈ 125 pg/ml)) will undergo open-access echocardiography. The diagnosis of heart failure (with reduced or preserved ejection fraction) is established by an expert panel consisting of two cardiologists and a general practitioner, according to the criteria of the European Society of Cardiology guidelines.Patients with newly established heart failure are allocated to either the 'care as usual' group or the 'intervention' group. Randomization is at the level of the general practitioner. In the intervention group general practitioners receive a single half-day training in heart failure management and the use of a structured up-titration scheme. All participants fill out quality of life questionnaires at baseline and after six months of follow-up. A six-minute walking test will be performed in patients with heart failure. Information on medication and hospitalization rates is extracted from the electronic medical files of the general practitioners. This study will provide information on the prevalence of unrecognized heart failure in elderly with shortness of breath on exertion, and the randomized comparison will reveal whether management based on a half-day training of general practitioners in the practical application of an up-titration scheme results in improvements in functionality, health-related quality of life, and uptake of heart failure medication in heart failure patients compared to care as usual. ClinicalTrials.gov NCT01202006.

Effects of Sacubitril/Valsartan on Physical and Social Activity Limitations in Patients With Heart Failure: A Secondary Analysis of the PARADIGM-HF Trial.

PubMed

Chandra, Alvin; Lewis, Eldrin F; Claggett, Brian L; Desai, Akshay S; Packer, Milton; Zile, Michael R; Swedberg, Karl; Rouleau, Jean L; Shi, Victor C; Lefkowitz, Martin P; Katova, Tzvetana; McMurray, John J V; Solomon, Scott D

2018-04-04

Health-related quality of life (HRQL) of patients with heart failure is markedly reduced compared with that in patients with other chronic diseases, demonstrating substantial limitations in physical and social activities. In the Prospective Comparison of ARNI With an ACE-Inhibitor to Determine Impact on Global Mortality and Morbidity in Heart Failure (PARADIGM-HF) trial, sacubitril/valsartan improved overall HRQL compared with enalapril, as determined by the Kansas City Cardiomyopathy Questionnaire (KCCQ). To examine the effects of sacubitril/valsartan on physical and social activities. The PARADIGM-HF trial was a randomized, double-blind, active treatment-controlled clinical trial performed from December 8, 2009, to March 31, 2014, in 8399 patients with New York Heart Association class II to IV disease and a left ventricular ejection fraction of 40% or less at 1043 centers in 38 countries. Data analysis was performed from August 1, 2017, to December 25, 2017. Sacubitril/valsartan, 200 mg twice daily, or enalapril, 10 mg twice daily. Patients completed HRQL assessments using the KCCQ at randomization, 4-month, 8-month, and annual visits. The effect of sacubitril/valsartan on components of the physical and social limitation sections of the KCCQ at 8 months and longitudinally and related biomarkers and clinical outcomes were studied. At baseline, 7618 of 8399 patients (90.7%) (mean [SD] age, 64 [11] years; 5987 [78.6%] male and 1631 [21.4%] female) completed the initial KCCQ assessment. Patients reported the greatest limitations at baseline in jogging and sexual relationships. Patients receiving sacubitril/valsartan had significantly better adjusted change scores in most physical and social activities at 8 months and during 36 months compared with those receiving enalapril. The largest improvement over enalapril was in household chores (adjusted change score difference, 2.35; 95% CI, 1.19-3.50; P < .001) and sexual relationships (adjusted change score difference, 2.72; 95% CI, 0.97-4.46; P = .002); both persisted through 36 months (overall change score difference, 1.69 [95% CI, 0.78-2.60], P < .001; and 2.36 [95% CI, 1.01-3.71], P = .001, respectively). In patients with heart failure with reduced ejection fraction, sacubitril/valsartan significantly improved nearly all KCCQ physical and social activities compared with enalapril, with the largest responses in household chores and sexual relationships. In addition to reduced likelihood of cardiovascular death, all-cause mortality, and heart failure hospitalization, sacubitril/valsartan may improve limitations in common activities in these patients. clinicaltrials.gov Identifier: NCT01035255.

Effects of physical guidance on short-term learning of walking on a narrow beam

PubMed Central

Domingo, Antoinette; Ferris, Daniel P.

2009-01-01

Physical guidance is often used in rehabilitation when teaching patients to re-learn movements. However, the effects of guidance on motor learning of complex skills, such as walking balance, are not clear. We tested four groups of healthy subjects that practiced walking on a narrow (1.27 cm) or wide (2.5 cm) treadmill-mounted balance beam, with or without physical guidance. Assistance was given by springs attached to a hip belt that applied restoring forces towards beam center. Subjects were evaluated while walking unassisted before and after training by calculating the number of times subjects stepped off of the beam per minute of successful walking on the beam (Failures per Minute). Subjects in Unassisted groups had greater performance improvements in walking balance from pre to post compared to subjects in Assisted groups. During training, Unassisted groups had more Failures per Minute than Assisted groups. Performance improvements were smaller in Narrow Beam groups than in Wide Beam groups. The Unassisted-Wide and Assisted-Narrow groups had similar Failures per Minute during training, but the Unassisted-Wide group had much greater performance gains after training. These results suggest that physical assistance can hinder motor learning of walking balance, assistance appears less detrimental for more difficult tasks, and task-specific dynamics are important to learning independent of error experience. PMID:19674900

Educational level and the quality of life of heart failure patients: a longitudinal study.

PubMed

Barbareschi, Giorgio; Sanderman, Robbert; Leegte, Ivonne Lesman; van Veldhuisen, Dirk J; Jaarsma, Tiny

2011-01-01

Lower education in heart failure (HF) patients is associated with high levels of anxiety, limited physical functioning, and an increased risk of hospitalization. We examined whether educational level is related to longitudinal differences in quality of life (QoL) in HF patients. This research is a substudy of the Coordinating study evaluating Outcomes of Advising and Counselling in Heart failure (COACH). QoL of 553 HF patients (mean age 69, 38% female, mean left ventricular ejection fraction 33%) was assessed during their hospitalization and at 4 follow-up measurements after discharge. In total 32% of the patients had very low, 24% low, 32% medium, and 12% high education. Patients with low educational levels reported the worst QoL. Significant differences between educational groups (P < .05) were only reported in physical functioning, social functioning, energy/fatigue, pain, and limitations in role functioning related to emotional problems. Longitudinal results show that a significantly higher proportion of high-educated patients improved in functional limitations related to emotional problems over time compared with lower-educated patients (P < .05). Patients with low educational levels reported the worst physical and functional condition. High-educated patients improved more than the other patients in functional limitations related to emotional problems over time. Low-educated patients may require different levels of intervention to improve their physical and functional condition. Copyright © 2011 Elsevier Inc. All rights reserved.

Discrete Element Method and its application to materials failure problem on the example of Brazilian Test

NASA Astrophysics Data System (ADS)

Klejment, Piotr; Kosmala, Alicja; Foltyn, Natalia; Dębski, Wojciech

2017-04-01

The earthquake focus is the point where a rock under external stress starts to fracture. Understanding earthquake nucleation and earthquake dynamics requires thus understanding of fracturing of brittle materials. This, however, is a continuing problem and enduring challenge to geoscience. In spite of significant progress we still do not fully understand the failure of rock materials due to extreme stress concentration in natural condition. One of the reason of this situation is that information about natural or induced seismic events is still not sufficient for precise description of physical processes in seismic foci. One of the possibility of improving this situation is using numerical simulations - a powerful tool of contemporary physics. For this reason we used an advanced implementation of the Discrete Element Method (DEM). DEM's main task is to calculate physical properties of materials which are represented as an assembly of a great number of particles interacting with each other. We analyze the possibility of using DEM for describing materials during so called Brazilian Test. Brazilian Test is a testing method to obtain the tensile strength of brittle material. One of the primary reasons for conducting such simulations is to measure macroscopic parameters of the rock sample. We would like to report our efforts of describing the fracturing process during the Brazilian Test from the microscopic point of view and give an insight into physical processes preceding materials failure.

A dislocation-based crystal plasticity framework for dynamic ductile failure of single crystals

DOE PAGES

Nguyen, Thao; Luscher, D. J.; Wilkerson, J. W.

2017-08-02

We developed a framework for dislocation-based viscoplasticity and dynamic ductile failure to model high strain rate deformation and damage in single crystals. The rate-dependence of the crystal plasticity formulation is based on the physics of relativistic dislocation kinetics suited for extremely high strain rates. The damage evolution is based on the dynamics of void growth, which are governed by both micro-inertia as well as dislocation kinetics and dislocation substructure evolution. Furthermore, an averaging scheme is proposed in order to approximate the evolution of the dislocation substructure in both the macroscale as well as its spatial distribution at the microscale. Inmore » addition, a concept of a single equivalent dislocation density that effectively captures the collective influence of dislocation density on all active slip systems is proposed here. Together, these concepts and approximations enable the use of semi-analytic solutions for void growth dynamics developed in [J. Wilkerson and K. Ramesh. A dynamic void growth model governed by dislocation kinetics. J. Mech. Phys. Solids, 70:262–280, 2014.], which greatly reduce the computational overhead that would otherwise be required. The resulting homogenized framework has been implemented into a commercially available finite element package, and a validation study against a suite of direct numerical simulations was carried out.« less

Reliability Assessment for Low-cost Unmanned Aerial Vehicles

NASA Astrophysics Data System (ADS)

Freeman, Paul Michael

Existing low-cost unmanned aerospace systems are unreliable, and engineers must blend reliability analysis with fault-tolerant control in novel ways. This dissertation introduces the University of Minnesota unmanned aerial vehicle flight research platform, a comprehensive simulation and flight test facility for reliability and fault-tolerance research. An industry-standard reliability assessment technique, the failure modes and effects analysis, is performed for an unmanned aircraft. Particular attention is afforded to the control surface and servo-actuation subsystem. Maintaining effector health is essential for safe flight; failures may lead to loss of control incidents. Failure likelihood, severity, and risk are qualitatively assessed for several effector failure modes. Design changes are recommended to improve aircraft reliability based on this analysis. Most notably, the control surfaces are split, providing independent actuation and dual-redundancy. The simulation models for control surface aerodynamic effects are updated to reflect the split surfaces using a first-principles geometric analysis. The failure modes and effects analysis is extended by using a high-fidelity nonlinear aircraft simulation. A trim state discovery is performed to identify the achievable steady, wings-level flight envelope of the healthy and damaged vehicle. Tolerance of elevator actuator failures is studied using familiar tools from linear systems analysis. This analysis reveals significant inherent performance limitations for candidate adaptive/reconfigurable control algorithms used for the vehicle. Moreover, it demonstrates how these tools can be applied in a design feedback loop to make safety-critical unmanned systems more reliable. Control surface impairments that do occur must be quickly and accurately detected. This dissertation also considers fault detection and identification for an unmanned aerial vehicle using model-based and model-free approaches and applies those algorithms to experimental faulted and unfaulted flight test data. Flight tests are conducted with actuator faults that affect the plant input and sensor faults that affect the vehicle state measurements. A model-based detection strategy is designed and uses robust linear filtering methods to reject exogenous disturbances, e.g. wind, while providing robustness to model variation. A data-driven algorithm is developed to operate exclusively on raw flight test data without physical model knowledge. The fault detection and identification performance of these complementary but different methods is compared. Together, enhanced reliability assessment and multi-pronged fault detection and identification techniques can help to bring about the next generation of reliable low-cost unmanned aircraft.

Pervasive Restart In MOOSE-based Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Derek Gaston; Cody Permann; David Andrs

Multiphysics applications are inherently complicated. Solving for multiple, interacting physical phenomena involves the solution of multiple equations, and each equation has its own data dependencies. Feeding the correct data to these equations at exactly the right time requires extensive effort in software design. In an ideal world, multiphysics applications always run to completion and produce correct answers. Unfortunately, in reality, there can be many reasons why a simulation might fail: power outage, system failure, exceeding a runtime allotment on a supercomputer, failure of the solver to converge, etc. A failure after many hours spent computing can be a significant setbackmore » for a project. Therefore, the ability to “continue” a solve from the point of failure, rather than starting again from scratch, is an essential component of any high-quality simulation tool. This process of “continuation” is commonly termed “restart” in the computational community. While the concept of restarting an application sounds ideal, the aforementioned complexities and data dependencies present in multiphysics applications make its implementation decidedly non-trivial. A running multiphysics calculation accumulates an enormous amount of “state”: current time, solution history, material properties, status of mechanical contact, etc. This “state” data comes in many different forms, including scalar, tensor, vector, and arbitrary, application-specific data types. To be able to restart an application, you must be able to both store and retrieve this data, effectively recreating the state of the application before the failure. When utilizing the Multiphysics Object Oriented Simulation Environment (MOOSE) framework developed at Idaho National Laboratory, this state data is stored both internally within the framework itself (such as solution vectors and the current time) and within the applications that use the framework. In order to implement restart in MOOSE-based applications, the total state of the system (both within the framework and without) must be stored and retrieved. To this end, the MOOSE team has implemented a “pervasive” restart capability which allows any object within MOOSE (or within a MOOSE-based application) to be declared as “state” data, and handles the storage and retrieval of said data.« less

Sensitivity analysis and calibration of a dynamic physically based slope stability model

NASA Astrophysics Data System (ADS)

Zieher, Thomas; Rutzinger, Martin; Schneider-Muntau, Barbara; Perzl, Frank; Leidinger, David; Formayer, Herbert; Geitner, Clemens

2017-06-01

Physically based modelling of slope stability on a catchment scale is still a challenging task. When applying a physically based model on such a scale (1 : 10 000 to 1 : 50 000), parameters with a high impact on the model result should be calibrated to account for (i) the spatial variability of parameter values, (ii) shortcomings of the selected model, (iii) uncertainties of laboratory tests and field measurements or (iv) parameters that cannot be derived experimentally or measured in the field (e.g. calibration constants). While systematic parameter calibration is a common task in hydrological modelling, this is rarely done using physically based slope stability models. In the present study a dynamic, physically based, coupled hydrological-geomechanical slope stability model is calibrated based on a limited number of laboratory tests and a detailed multitemporal shallow landslide inventory covering two landslide-triggering rainfall events in the Laternser valley, Vorarlberg (Austria). Sensitive parameters are identified based on a local one-at-a-time sensitivity analysis. These parameters (hydraulic conductivity, specific storage, angle of internal friction for effective stress, cohesion for effective stress) are systematically sampled and calibrated for a landslide-triggering rainfall event in August 2005. The identified model ensemble, including 25 behavioural model runs with the highest portion of correctly predicted landslides and non-landslides, is then validated with another landslide-triggering rainfall event in May 1999. The identified model ensemble correctly predicts the location and the supposed triggering timing of 73.0 % of the observed landslides triggered in August 2005 and 91.5 % of the observed landslides triggered in May 1999. Results of the model ensemble driven with raised precipitation input reveal a slight increase in areas potentially affected by slope failure. At the same time, the peak run-off increases more markedly, suggesting that precipitation intensities during the investigated landslide-triggering rainfall events were already close to or above the soil's infiltration capacity.

Generalization of Tactics in Tag Rugby from Practice to Games in Middle School Physical Education

ERIC Educational Resources Information Center

Lee, Myung-Ah; Ward, Phillip

2009-01-01

Background: Many of the issues relating to game performance of students found in the physical education literature can be considered a failure of generalization from practices to games, and from games to games. However, no study in secondary physical education has examined generalization effects as a result of effective game pedagogy in the…

Simulating direct shear tests with the Bullet physics library: A validation study.

PubMed

Izadi, Ehsan; Bezuijen, Adam

2018-01-01

This study focuses on the possible uses of physics engines, and more specifically the Bullet physics library, to simulate granular systems. Physics engines are employed extensively in the video gaming, animation and movie industries to create physically plausible scenes. They are designed to deliver a fast, stable, and optimal simulation of certain systems such as rigid bodies, soft bodies and fluids. This study focuses exclusively on simulating granular media in the context of rigid body dynamics with the Bullet physics library. The first step was to validate the results of the simulations of direct shear testing on uniform-sized metal beads on the basis of laboratory experiments. The difference in the average angle of mobilized frictions was found to be only 1.0°. In addition, a very close match was found between dilatancy in the laboratory samples and in the simulations. A comprehensive study was then conducted to determine the failure and post-failure mechanism. We conclude with the presentation of a simulation of a direct shear test on real soil which demonstrated that Bullet has all the capabilities needed to be used as software for simulating granular systems.

Getting physical to fix pharma

NASA Astrophysics Data System (ADS)

Connelly, Patrick R.; Vuong, T. Minh; Murcko, Mark A.

2011-09-01

Powerful technologies allow the synthesis and testing of large numbers of new compounds, but the failure rate of pharmaceutical R&D remains very high. Greater understanding of the fundamental physical chemical behaviour of molecules could be the key to greatly enhancing the success rate of drug discovery.

A theory-based exercise intervention in patients with heart failure: A protocol for randomized, controlled trial

PubMed Central

Rajati, Fatemeh; Mostafavi, Firoozeh; Sharifirad, Gholamreza; Sadeghi, Masoomeh; Tavakol, Kamran; Feizi, Awat; Pashaei, Tahereh

2013-01-01

Background: Regular exercise has been associated with improved quality of life (QoL) in patients with heart failure (HF). However, less is known on the theoretical framework, depicting how educational intervention on psychological, social, and cognitive variables affects physical activity (PA). The purpose of this study is to assess the effectiveness of a social cognitive theory-based (SCT-based) exercise intervention in patients with HF. Materials and Methods: This is a randomized controlled trial, with measurements at baseline, immediately following the intervention, and at 1, 3, and 6 months follow-up. Sixty patients who are referred to the cardiac rehabilitation (CR) unit and meet the inclusion criteria will be randomly allocated to either an intervention group or a usual-care control group. Data will be collected using various methods (i.e., questionnaires, physical tests, paraclinical tests, patients’ interviews, and focus groups). The patients in the intervention group will receive eight face-to-face counseling sessions, two focus groups, and six educational sessions over a 2-month period. The intervention will include watching videos, using book and pamphlets, and sending short massage services to the participants. The primary outcome measures are PA and QoL. The secondary outcome measures will be the components of SCT, heart rate and blood pressure at rest, body mass index, left ventricular ejection fraction, exercise capacity, and maximum heart rate. Conclusion: The findings of this trial may assist with the development of a theoretical model for exercise intervention in CR. The intervention seems to be promising and has the potential to bridge the gap of the usually limited and incoherent provision of educational care in the CR setting. PMID:24379841

Predicting subsequent task performance from goal motivation and goal failure.

PubMed

Healy, Laura C; Ntoumanis, Nikos; Stewart, Brandon D; Duda, Joan L

2015-01-01

Recent research has demonstrated that the cognitive processes associated with goal pursuit can continue to interfere with unrelated tasks when a goal is unfulfilled. Drawing from the self-regulation and goal-striving literatures, the present study explored the impact of goal failure on subsequent cognitive and physical task performance. Furthermore, we examined if the autonomous or controlled motivation underpinning goal striving moderates the responses to goal failure. Athletes (75 male, 59 female, Mage = 19.90 years, SDage = 3.50) completed a cycling trial with the goal of covering a given distance in 8 min. Prior to the trial, their motivation was primed using a video. During the trial they were provided with manipulated performance feedback, thus creating conditions of goal success or failure. No differences emerged in the responses to goal failure between the primed motivation or performance feedback conditions. We make recommendations for future research into how individuals can deal with failure in goal striving.

Predictability of Landslide Timing From Quasi-Periodic Precursory Earthquakes

NASA Astrophysics Data System (ADS)

Bell, Andrew F.

2018-02-01

Accelerating rates of geophysical signals are observed before a range of material failure phenomena. They provide insights into the physical processes controlling failure and the basis for failure forecasts. However, examples of accelerating seismicity before landslides are rare, and their behavior and forecasting potential are largely unknown. Here I use a Bayesian methodology to apply a novel gamma point process model to investigate a sequence of quasiperiodic repeating earthquakes preceding a large landslide at Nuugaatsiaq in Greenland in June 2017. The evolution in earthquake rate is best explained by an inverse power law increase with time toward failure, as predicted by material failure theory. However, the commonly accepted power law exponent value of 1.0 is inconsistent with the data. Instead, the mean posterior value of 0.71 indicates a particularly rapid acceleration toward failure and suggests that only relatively short warning times may be possible for similar landslides in future.

Improving Patient Outcomes With Oral Heart Failure Medications.

PubMed

Sherrod, Melissa M; Cheek, Dennis J; Seale, Ashlie

2016-05-01

Hospitals are under immense pressure to reduce heart failure readmissions that occur within 30 days of discharge, and to improve the quality of care for these patients. Penalties mandated by the Affordable Care Act decrease hospital reimbursement and ultimately the overall cost of caring for these patients increases if they are not well managed. Approximately 25% of patients hospitalized for heart failure are at high risk for readmission and these rates have not changed over the past decade. As a result of an aging population, the incidence of heart failure is expected to increase to one in five Americans over the age of 65. Pharmacologic management can reduce the risk of death and help prevent unnecessary hospitalizations. Healthcare providers who have knowledge of heart failure medications and drug interactions and share this information with their patients contribute to improved long-term survival and physical functioning as well as fewer hospitalizations and a delay of progressive worsening of heart failure.

Savannah River Site generic data base development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blanton, C.H.; Eide, S.A.

This report describes the results of a project to improve the generic component failure data base for the Savannah River Site (SRS). A representative list of components and failure modes for SRS risk models was generated by reviewing existing safety analyses and component failure data bases and from suggestions from SRS safety analysts. Then sources of data or failure rate estimates were identified and reviewed for applicability. A major source of information was the Nuclear Computerized Library for Assessing Reactor Reliability, or NUCLARR. This source includes an extensive collection of failure data and failure rate estimates for commercial nuclear powermore » plants. A recent Idaho National Engineering Laboratory report on failure data from the Idaho Chemical Processing Plant was also reviewed. From these and other recent sources, failure data and failure rate estimates were collected for the components and failure modes of interest. This information was aggregated to obtain a recommended generic failure rate distribution (mean and error factor) for each component failure mode.« less

'As many options as there are, there are just not enough for me': contraceptive use and barriers to access among Australian women.

PubMed

Dixon, Suzanne C; Herbert, Danielle L; Loxton, Deborah; Lucke, Jayne C

2014-10-01

A comprehensive life course perspective of women's experiences in obtaining and using contraception in Australia is lacking. This paper explores free-text comments about contraception provided by women born between 1973 and 1978 who participated in the Australian Longitudinal Study on Women's Health (ALSWH). The ALSWH is a national population-based cohort study involving over 40,000 women from three age groups, who are surveyed every three years. An initial search identified 1600 comments from 690 women across five surveys from 1996 (when they were aged 18-23 years) to 2009 (31-36 years). The analysis included 305 comments from 289 participants. Factors relating to experiences of barriers to access and optimal contraceptive use were identified and explored using thematic analysis. Five themes recurred across the five surveys as women aged: (i) side effects affecting physical and mental health; (ii) lack of information about contraception; (iii) negative experiences with health services; (iv) contraceptive failure; and (v) difficulty with accessing contraception. Side effects of hormonal contraception and concerns about contraceptive failure influence women's mental and physical health. Many barriers to effective contraception persist throughout women's reproductive lives. Further research is needed into reducing barriers and minimising negative experiences, to ensure optimal contraceptive access for Australian women.

Ultimate compression after impact load prediction in graphite/epoxy coupons using neural network and multivariate statistical analyses

NASA Astrophysics Data System (ADS)

Gregoire, Alexandre David

2011-07-01

The goal of this research was to accurately predict the ultimate compressive load of impact damaged graphite/epoxy coupons using a Kohonen self-organizing map (SOM) neural network and multivariate statistical regression analysis (MSRA). An optimized use of these data treatment tools allowed the generation of a simple, physically understandable equation that predicts the ultimate failure load of an impacted damaged coupon based uniquely on the acoustic emissions it emits at low proof loads. Acoustic emission (AE) data were collected using two 150 kHz resonant transducers which detected and recorded the AE activity given off during compression to failure of thirty-four impacted 24-ply bidirectional woven cloth laminate graphite/epoxy coupons. The AE quantification parameters duration, energy and amplitude for each AE hit were input to the Kohonen self-organizing map (SOM) neural network to accurately classify the material failure mechanisms present in the low proof load data. The number of failure mechanisms from the first 30% of the loading for twenty-four coupons were used to generate a linear prediction equation which yielded a worst case ultimate load prediction error of 16.17%, just outside of the +/-15% B-basis allowables, which was the goal for this research. Particular emphasis was placed upon the noise removal process which was largely responsible for the accuracy of the results.

Etiology, clinical features and outcome of fulminant hepatic failure in pregnancy.

PubMed

Brohi, Zahida Parveen; Sadaf, Aneela; Perveen, Uzma

2013-09-01

To determine the etiology, clinical features and outcome of fulminant hepatic failure in pregnancy. An observational hospital based study was conducted at Isra University hospital Hyderabad from 1st March 2009 to 28th February 2010. Total 1192 obstetric patients were admitted in obstetrics & gynaecology department during this period, of whom 52 were with Fulminant hepatic failure in pregnancy and were included in this study. A pre-designed structured proforma was used. All patients had clinical history and underwent a physical examination. Routine laboratory tests, liver function tests and viral serology were performed in all cases. All results were analyzed on statistical software SPSS version 11. Frequencies and percentages were calculated, the final outcome was recorded. Out of 52, 6 (11.5%) presented in the first trimester, 4 (7.6%) in the second trimester and 42 (80.7%) were in their 3rd trimester of pregnancy. Etiology of the disease was Hepatitis E in 28 (53.8%), Hepatitis B in 9 (17.3%), Hepatitis C in 7 (13.5%) HELLP syndrome in 7 (13.5%) and acute fatty liver of pregnancy in 1 (3.57%) case. Maternal mortality was 15 (28.8%) and foetal mortality was 40 (77%). Only 12 (23.1%) new born remained alive. Fulminant hepatic failure in pregnancy has very high foetal and maternal mortality which is mostly due to viral hepatitis E.

How Things Work: Teaching Physics in the Context of Everyday Objects

NASA Astrophysics Data System (ADS)

Bloomfield, Louis

2015-03-01

How Things Work is an unconventional introduction to physics, a course that starts with whole objects and looks inside them to see what makes them work. Effectively ``case-study physics,'' it is designed primarily for non-science students who are unsure of the role of physics in the world and are looking for relevance in their studies. How Things Work is essentially the generalization of context-based introductory courses (Physics of the Human Body, Physics of the Automobile, and Physics of Music) and demonstrates that when physics is taught in the context of ordinary objects, these students are enthusiastic about it, look forward to classes, ask insightful questions, experiment on their own, and find themselves explaining to friends and family how things in their world work. In this talk, I will discuss the concept and structure of a How Things Work course and look briefly at how to teach its objects and assess what students learn from it. Although this course focuses on concepts rather than on calculations, it is rich in physics and requires that students think hard about the world around them. It also teaches problem solving and logical thinking skills, and demands that students face their misconceptions and failures of intuition. Lastly, it is actually quantitative in many respects, though its results are usually more words than numbers: your weight, the battery's voltage, or the acceleration due to gravity.

Structural health monitoring of wind turbine blades : SE 265 Final Project.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barkley, W. C.; Jacobs, Laura D.; Rutherford, A. C.

2006-03-23

ACME Wind Turbine Corporation has contacted our dynamic analysis firm regarding structural health monitoring of their wind turbine blades. ACME has had several failures in previous years. Examples are shown in Figure 1. These failures have resulted in economic loss for the company due to down time of the turbines (lost revenue) and repair costs. Blade failures can occur in several modes, which may depend on the type of construction and load history. Cracking and delamination are some typical modes of blade failure. ACME warranties its turbines and wishes to decrease the number of blade failures they have to repairmore » and replace. The company wishes to implement a real time structural health monitoring system in order to better understand when blade replacement is necessary. Because of warranty costs incurred to date, ACME is interested in either changing the warranty period for the blades in question or predicting imminent failure before it occurs. ACME's current practice is to increase the number of physical inspections when blades are approaching the end of their fatigue lives. Implementation of an in situ monitoring system would eliminate or greatly reduce the need for such physical inspections. Another benefit of such a monitoring system is that the life of any given component could be extended since real conditions would be monitored. The SHM system designed for ACME must be able to operate while the wind turbine is in service. This means that wireless communication options will likely be implemented. Because blade failures occur due to cyclic stresses in the blade material, the sensing system will focus on monitoring strain at various points.« less

The Bending Strength, Internal Bonding and Thickness Swelling of a Five Layer Sandwiched Bamboo Particleboard

NASA Astrophysics Data System (ADS)

Jamaludin, M. A.; Bahari, S. A.; Nordin, K.; Soh, T. F. T.

2010-03-01

The demand for wood based material is increasing but the supply is decreasing. Therefore the price of these raw materials has increased. Bamboo provides an economically feasible alternative raw material for the wood based industry. Its properties are comparable to wood. It is also compatible with the existing processing technology. Bamboo is in abundance, easy to propagate and of short maturation period. Bamboo provides a cheaper alternative resource for the wood based industry. The development of new structural components from bamboo will widen its area of application from handicrafts to furniture and building components. In this study, five layer sandwiched bamboo particleboard were manufactured. The sandwiched Bamboo PB consists of a bamboo PB core, oil palm middle veneers and thin meranti surface veneers. The physical and mechanical properties of the bamboo sandwiched particleboards were tested in accordance to the BS-EN 317:1993 [1] and BS-EN 310:1993 [2], respectively. All the samples passed the standards. The modulus of elasticity was about 352% higher than the value specified in the BS standard, BS-EN 312-4:1996 [3]. The Internal bonding was about 23% higher than the general requirements specified in the standard. On the other hand, the thickness swelling was about 6% lower than the standard. No glue line failure was observed in the strength tests. Critical failures in the IB tests were observed in the particleboards. Tension failures were observed in the surface veneers in the bending tests. The five layer sandwiched bamboo particleboard can be used for light weight construction such as furniture, and wall and door panels in buildings.

Brain natriuretic peptide-guided therapy in the inpatient management of decompensated heart failure.

PubMed

Saremi, Adonis; Gopal, Dipika; Maisel, Alan S

2012-02-01

Heart failure is extremely prevalent and is associated with significant mortality, morbidity and cost. Studies have already established mortality benefit with the use of neurohormonal blockade therapy in systolic failure. Unfortunately, physical signs and symptoms of heart failure lack diagnostic sensitivity and specificity, and medication doses proven to improve mortality in clinical trials are often not achieved. Brain natriuretic peptide (BNP) has proven to be of clinical use in the diagnosis and prognosis of heart failure, and recent efforts have been taken to further elucidate its role in guiding heart failure management. Multiple studies have been conducted on outpatient guided management, and although still controversial, there is a trend towards improved outcomes. Inpatient studies are lacking, but preliminary data suggest various BNP cut-off values, as well as percentage changes in BNP, that could be useful in predicting outcomes and improving mortality. In the future, heart failure management will probably involve an algorithm using clinical assessment and a multibiomarker-guided approach.

Catch-Up Growth Assessment in Long-Term Physically Neglected and Emotionally Abused Preschool Age Male Children.

ERIC Educational Resources Information Center

Olivan, Gonzalo

2003-01-01

A longitudinal study examined 20 neglected and emotionally abused boys (ages 30-42 months) who entered foster residential care and remained a year after initial placement. At placement, children showed a mild form of chronic malnutrition with growth failure. Growth failure was reversible after the first year of stay. (Contains references.)…

Congenital mitral stenosis, subvalvular aortic stenosis, and congestive heart failure in a duck.

PubMed

Mitchell, Elizabeth B; Hawkins, Michelle G; Orvalho, Joao S; Thomas, William P

2008-06-01

A 2.6-year-old duck was evaluated for respiratory difficulty. On the basis of physical, radiographic and echocardiographic findings, a diagnosis of congestive heart failure secondary to congenital mitral stenosis and subvalvular aortic stenosis was made. The duck did not respond well to medical therapy and was euthanized. The diagnosis was confirmed at necropsy.

Multiscale modeling of ductile failure in metallic alloys

NASA Astrophysics Data System (ADS)

Pardoen, Thomas; Scheyvaerts, Florence; Simar, Aude; Tekoğlu, Cihan; Onck, Patrick R.

2010-04-01

Micromechanical models for ductile failure have been developed in the 1970s and 1980s essentially to address cracking in structural applications and complement the fracture mechanics approach. Later, this approach has become attractive for physical metallurgists interested by the prediction of failure during forming operations and as a guide for the design of more ductile and/or high-toughness microstructures. Nowadays, a realistic treatment of damage evolution in complex metallic microstructures is becoming feasible when sufficiently sophisticated constitutive laws are used within the context of a multilevel modelling strategy. The current understanding and the state of the art models for the nucleation, growth and coalescence of voids are reviewed with a focus on the underlying physics. Considerations are made about the introduction of the different length scales associated with the microstructure and damage process. Two applications of the methodology are then described to illustrate the potential of the current models. The first application concerns the competition between intergranular and transgranular ductile fracture in aluminum alloys involving soft precipitate free zones along the grain boundaries. The second application concerns the modeling of ductile failure in friction stir welded joints, a problem which also involves soft and hard zones, albeit at a larger scale.

TU-FG-201-01: 18-Month Clinical Experience of a Linac Daily Quality Assurance (QA) Solution Using Only EPID and OBI

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, B; Sun, B; Yaddanapudi, S

Purpose: To describe the clinical use of a Linear Accelerator (Linac) DailyQA system with only EPID and OBI. To assess the reliability over an 18-month period and improve the robustness of this system based on QA failure analysis. Methods: A DailyQA solution utilizing an in-house designed phantom, combined EPID and OBI image acquisitions, and a web-based data analysis and reporting system was commissioned and used in our clinic to measure geometric, dosimetry and imaging components of a Varian Truebeam Linac. During an 18-month period (335 working days), the Daily QA results, including the output constancy, beam flatness and symmetry, uniformity,more » TPR20/10, MV and KV imaging quality, were collected and analyzed. For output constancy measurement, an independent monthly QA system with an ionization chamber (IC) and annual/incidental TG51 measurements with ADCL IC were performed and cross-compared to Daily QA system. Thorough analyses were performed on the recorded QA failures to evaluate the machine performance, optimize the data analysis algorithm, adjust the tolerance setting and improve the training procedure to prevent future failures. Results: A clinical workflow including beam delivery, data analysis, QA report generation and physics approval was established and optimized to suit daily clinical operation. The output tests over the 335 working day period cross-correlated with the monthly QA system within 1.3% and TG51 results within 1%. QA passed with one attempt on 236 days out of 335 days. Based on the QA failures analysis, the Gamma criteria is revised from (1%, 1mm) to (2%, 1mm) considering both QA accuracy and efficiency. Data analysis algorithm is improved to handle multiple entries for a repeating test. Conclusion: We described our 18-month clinical experience on a novel DailyQA system using only EPID and OBI. The long term data presented demonstrated the system is suitable and reliable for Linac daily QA.« less

Treating the untreated: applying a community-based, culturally sensitive psychiatric intervention to confined and physically restrained mentally ill individuals in Bali, Indonesia.

PubMed

Suryani, Luh Ketut; Lesmana, Cokorda Bagus Jaya; Tiliopoulos, Niko

2011-11-01

This study identified, mapped and treated the clinical features of mentally ill people, who had been isolated and restrained by family and community members as a result of a functional failure of the traditional medical, hospital-based mental health model currently practiced in Indonesia. A 10-month epidemiological population survey was carried out in Karangasem regency of Bali, Indonesia. A total of 404,591 individuals were clinically interviewed, of which 895 individuals with mental health problems were identified, with 23 satisfying criteria of physical restraint and confinement. Of the latter, twenty were males; age range was 19-69 years, all diagnosed by the researchers with schizophrenia-spectrum disorder (ICD-10 diagnostic criteria). Duration of restraint ranged from 3 months to 30 years (mean = 8.1 years, SD = 8.3 years). Through the application of a holistic intervention model, all patients exhibited a remarkable recovery within 19 months of treatment. We conclude that the development of a community-based, culturally sensitive and respectful mental health model can serve as an optimum promoter of positive mental health outcomes.

[Improvement in functional capacity after levothyroxine treatment in patients with chronic heart failure and subclinical hypothyroidism].

PubMed

Curotto Grasiosi, Jorge; Peressotti, Bruno; Machado, Rogelio A; Filipini, Eduardo C; Angel, Adriana; Delgado, Jorge; Cortez Quiroga, Gustavo A; Rus Mansilla, Carmen; Martínez Quesada, María del Mar; Degregorio, Alejandro; Cordero, Diego J; Dak, Marcelo; Izurieta, Carlos; Esper, Ricardo J

2013-10-01

To assess whether levothyroxine treatment improves functional capacity in patients with chronic heart failure (New York Heart Association class i-iii) and subclinical hypothyroidism. One hundred and sixty-three outpatients with stable chronic heart failure followed up for at least 6 months were enrolled. A physical examination was performed, and laboratory tests including thyroid hormone levels, Doppler echocardiogram, radionuclide ventriculography, and Holter monitoring were requested. Functional capacity was assessed by of the 6-min walk test. Patients with subclinical hypothyroidism were detected and, after undergoing the s6-min walk test, were given replacement therapy. When they reached normal thyrotropin (TSH) levels, the 6-min walk test was performed again. The distance walked in both tests was recorded, and the difference in meters covered by each patient was analyzed. Prevalence of subclinical hypothyroidism in patients with heart failure was 13%. These patients walked 292±63m while they were hypothyroid and 350±76m when TSH levels returned to normal, a difference of 58±11m (P<.011). Patients with normal baseline TSH levels showed no significant difference between the 2 6-min walk tests. Patients with chronic heart failure and subclinical hypothyroidism significantly improved their physical performance when normal TSH levels were reached. Copyright © 2012 SEEN. Published by Elsevier Espana. All rights reserved.

Physically-based Assessment of Tropical Cyclone Damage and Economic Losses

NASA Astrophysics Data System (ADS)

Lin, N.

2012-12-01

Estimating damage and economic losses caused by tropical cyclones (TC) is a topic of considerable research interest in many scientific fields, including meteorology, structural and coastal engineering, and actuarial sciences. One approach is based on the empirical relationship between TC characteristics and loss data. Another is to model the physical mechanism of TC-induced damage. In this talk we discuss about the physically-based approach to predict TC damage and losses due to extreme wind and storm surge. We first present an integrated vulnerability model, which, for the first time, explicitly models the essential mechanisms causing wind damage to residential areas during storm passage, including windborne-debris impact and the pressure-debris interaction that may lead, in a chain reaction, to structural failures (Lin and Vanmarcke 2010; Lin et al. 2010a). This model can be used to predict the economic losses in a residential neighborhood (with hundreds of buildings) during a specific TC (Yau et al. 2011) or applied jointly with a TC risk model (e.g., Emanuel et al 2008) to estimate the expected losses over long time periods. Then we present a TC storm surge risk model that has been applied to New York City (Lin et al. 2010b; Lin et al. 2012; Aerts et al. 2012), Miami-Dade County, Florida (Klima et al. 2011), Galveston, Texas (Lickley, 2012), and other coastal areas around the world (e.g., Tampa, Florida; Persian Gulf; Darwin, Australia; Shanghai, China). These physically-based models are applicable to various coastal areas and have the capability to account for the change of the climate and coastal exposure over time. We also point out that, although made computationally efficient for risk assessment, these models are not suitable for regional or global analysis, which has been a focus of the empirically-based economic analysis (e.g., Hsiang and Narita 2012). A future research direction is to simplify the physically-based models, possibly through parameterization, and make connections to the global loss data and economic analysis.

Methodology for the Incorporation of Passive Component Aging Modeling into the RAVEN/ RELAP-7 Environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mandelli, Diego; Rabiti, Cristian; Cogliati, Joshua

2014-11-01

Passive system, structure and components (SSCs) will degrade over their operation life and this degradation may cause to reduction in the safety margins of a nuclear power plant. In traditional probabilistic risk assessment (PRA) using the event-tree/fault-tree methodology, passive SSC failure rates are generally based on generic plant failure data and the true state of a specific plant is not reflected realistically. To address aging effects of passive SSCs in the traditional PRA methodology [1] does consider physics based models that account for the operating conditions in the plant, however, [1] does not include effects of surveillance/inspection. This paper representsmore » an overall methodology for the incorporation of aging modeling of passive components into the RAVEN/RELAP-7 environment which provides a framework for performing dynamic PRA. Dynamic PRA allows consideration of both epistemic and aleatory uncertainties (including those associated with maintenance activities) in a consistent phenomenological and probabilistic framework and is often needed when there is complex process/hardware/software/firmware/ human interaction [2]. Dynamic PRA has gained attention recently due to difficulties in the traditional PRA modeling of aging effects of passive components using physics based models and also in the modeling of digital instrumentation and control systems. RAVEN (Reactor Analysis and Virtual control Environment) [3] is a software package under development at the Idaho National Laboratory (INL) as an online control logic driver and post-processing tool. It is coupled to the plant transient code RELAP-7 (Reactor Excursion and Leak Analysis Program) also currently under development at INL [3], as well as RELAP 5 [4]. The overall methodology aims to: • Address multiple aging mechanisms involving large number of components in a computational feasible manner where sequencing of events is conditioned on the physical conditions predicted in a simulation environment such as RELAP-7. • Identify the risk-significant passive components, their failure modes and anticipated rates of degradation • Incorporate surveillance and maintenance activities and their effects into the plant state and into component aging progress. • Asses aging affects in a dynamic simulation environment 1. C. L. SMITH, V. N. SHAH, T. KAO, G. APOSTOLAKIS, “Incorporating Ageing Effects into Probabilistic Risk Assessment –A Feasibility Study Utilizing Reliability Physics Models,” NUREG/CR-5632, USNRC, (2001). 2. T. ALDEMIR, “A Survey of Dynamic Methodologies for Probabilistic Safety Assessment of Nuclear Power Plants, Annals of Nuclear Energy, 52, 113-124, (2013). 3. C. RABITI, A. ALFONSI, J. COGLIATI, D. MANDELLI and R. KINOSHITA “Reactor Analysis and Virtual Control Environment (RAVEN) FY12 Report,” INL/EXT-12-27351, (2012). 4. D. ANDERS et.al, "RELAP-7 Level 2 Milestone Report: Demonstration of a Steady State Single Phase PWR Simulation with RELAP-7," INL/EXT-12-25924, (2012).« less

American Heart Association’s Life’s Simple 7: Avoiding Heart Failure and Preserving Cardiac Structure and Function

PubMed Central

Folsom, Aaron R.; Shah, Amil M.; Lutsey, Pamela L.; Roetker, Nicholas S.; Alonso, Alvaro; Avery, Christy L.; Miedema, Michael D.; Konety, Suma; Chang, Patricia P.; Solomon, Scott D.

2015-01-01

BACKGROUND Many people may underappreciate the role of lifestyle in avoiding heart failure. We estimated whether greater adherence in middle age to American Heart Association’s Life’s Simple 7 guidelines -- on smoking, body mass, physical activity, diet, cholesterol, blood pressure, and glucose -- is associated with lower lifetime risk of heart failure and greater preservation of cardiac structure and function in old age. METHODS We studied the population-based Atherosclerosis Risk in Communities Study cohort of 13,462 adults aged 45-64 years in 1987-89. From the 1987-89 risk factor measurements, we created a Life’s Simple 7 score (range 0-14, giving 2 points for ideal, 1 point for intermediate, and 0 points for poor components). We identified 2,218 incident heart failure events using surveillance of hospital discharge and death codes through 2011. In addition, in 4,855 participants free of clinical cardiovascular disease in 2011-13, we performed echocardiography from which we quantified left ventricular hypertrophy and diastolic dysfunction. RESULTS One in four participants (25.5%) developed heart failure through age 85. Yet, this lifetime heart failure risk was 14.4% for those with a middle-age Life’s Simple 7 score of 10-14 (optimal), 26.8% for a score of 5-9 (average), and 48.6% for a score of 0-4 (inadequate). Among those with no clinical cardiovascular event, the prevalence of left ventricular hypertrophy in late life was approximately 40% as common, and diastolic dysfunction was approximately 60% as common, among those with an optimal middle-age Life’s Simple 7 score compared with an inadequate score. CONCLUSIONS Greater achievement of American Heart Association’s Life’s Simple 7 in middle-age is associated with a lower lifetime occurrence of heart failure and greater preservation of cardiac structure and function. PMID:25908393

The effect of a virtual reality exercise program on physical fitness, body composition, and fatigue in hemodialysis patients.

PubMed

Cho, Hyeyoung; Sohng, Kyeong-Yae

2014-10-01

[Purpose] The aim of the present study was to investigate the effects of a virtual reality exercise program (VREP) on physical fitness, body composition, and fatigue in hemodialysis (HD) patients with end-stage renal failure. [Subjects and Methods] A nonequivalent control group pretest-posttest design was used. Forty-six HD patients were divided into exercise (n=23) and control groups (n=23); while waiting for their dialyses, the exercise group followed a VREP, and the control group received only their usual care. The VREP was accomplished using Nintendo's Wii Fit Plus for 40 minutes, 3 times a week for 8 weeks during the period of May 27 to July 19, 2013. Physical fitness (muscle strength, balance, flexibility), body composition (skeletal muscle mass, body fat rate, arm and leg muscle mass), and fatigue were measured at baseline and after the intervention. [Results] After the VREP, physical fitness and body composition significantly increased, and the level of fatigue significantly decreased in the exercise group. [Conclusion] These results suggest that a VREP improves physical fitness, body composition, and fatigue in HD patients. Based on the findings, VREPs should be used as a health promotion programs for HD patients.

Prevalence of and Risk Factors for Elder Abuse and Neglect in the Community: A Population-Based Study.

PubMed

Burnes, David; Pillemer, Karl; Caccamise, Paul L; Mason, Art; Henderson, Charles R; Berman, Jacquelin; Cook, Ann Marie; Shukoff, Denise; Brownell, Patricia; Powell, Mebane; Salamone, Aurora; Lachs, Mark S

2015-09-01

To estimate past-year prevalence and identify risk and protective factors of elder emotional abuse, physical abuse, and neglect. Cross-sectional, population-based study using random-digit-dial sampling and direct telephone interviews. New York State households. Representative (race, ethnicity, sex) sample (N = 4,156) of English- or Spanish-speaking, community-dwelling, cognitively intact individuals aged 60 and older. The Conflict Tactics Scale was adapted to assess elder emotional and physical abuse. Elder neglect was evaluated according to failure of a responsible caregiver to meet an older adult's needs using the Duke Older Americans Resources and Services (OARS) scale. Caseness thresholds were based on mistreatment behavior frequencies and elder perceptions of problem seriousness. Past-year prevalence of elder emotional abuse was 1.9%, of physical abuse was 1.8%, and of neglect was 1.8%, with an aggregate prevalence of 4.6%. Emotional and physical abuse were associated with being separated or divorced, living in a lower-income household, functional impairment, and younger age. Neglect was associated with poor health, being separated or divorced, living below the poverty line, and younger age. Neglect was less likely in older adults of Hispanic ethnicity. Elder abuse and neglect are common problems, with divergent risk and protective factor profiles. These findings have direct implications for public screening and education and awareness efforts designed to prevent elder mistreatment. © 2015, Copyright the Authors Journal compilation © 2015, The American Geriatrics Society.

Studies in knowledge-based diagnosis of failures in robotic assembly

NASA Technical Reports Server (NTRS)

Lam, Raymond K.; Pollard, Nancy S.; Desai, Rajiv S.

1990-01-01

The telerobot diagnostic system (TDS) is a knowledge-based system that is being developed for identification and diagnosis of failures in the space robotic domain. The system is able to isolate the symptoms of the failure, generate failure hypotheses based on these symptoms, and test their validity at various levels by interpreting or simulating the effects of the hypotheses on results of plan execution. The implementation of the TDS is outlined. The classification of failures and the types of system models used by the TDS are discussed. A detailed example of the TDS approach to failure diagnosis is provided.

Creep stability of the proposed AIDA mission target 65803 Didymos: I. Discrete cohesionless granular physics model

NASA Astrophysics Data System (ADS)

Zhang, Yun; Richardson, Derek C.; Barnouin, Olivier S.; Maurel, Clara; Michel, Patrick; Schwartz, Stephen R.; Ballouz, Ronald-Louis; Benner, Lance A. M.; Naidu, Shantanu P.; Li, Junfeng

2017-09-01

As the target of the proposed Asteroid Impact & Deflection Assessment (AIDA) mission, the near-Earth binary asteroid 65803 Didymos represents a special class of binary asteroids, those whose primaries are at risk of rotational disruption. To gain a better understanding of these binary systems and to support the AIDA mission, this paper investigates the creep stability of the Didymos primary by representing it as a cohesionless self-gravitating granular aggregate subject to rotational acceleration. To achieve this goal, a soft-sphere discrete element model (SSDEM) capable of simulating granular systems in quasi-static states is implemented and a quasi-static spin-up procedure is carried out. We devise three critical spin limits for the simulated aggregates to indicate their critical states triggered by reshaping and surface shedding, internal structural deformation, and shear failure, respectively. The failure condition and mode, and shear strength of an aggregate can all be inferred from the three critical spin limits. The effects of arrangement and size distribution of constituent particles, bulk density, spin-up path, and interparticle friction are numerically explored. The results show that the shear strength of a spinning self-gravitating aggregate depends strongly on both its internal configuration and material parameters, while its failure mode and mechanism are mainly affected by its internal configuration. Additionally, this study provides some constraints on the possible physical properties of the Didymos primary based on observational data and proposes a plausible formation mechanism for this binary system. With a bulk density consistent with observational uncertainty and close to the maximum density allowed for the asteroid, the Didymos primary in certain configurations can remain geo-statically stable without requiring cohesion.

Reevaluating the two-representation model of numerical magnitude processing.

PubMed

Jiang, Ting; Zhang, Wenfeng; Wen, Wen; Zhu, Haiting; Du, Han; Zhu, Xiangru; Gao, Xuefei; Zhang, Hongchuan; Dong, Qi; Chen, Chuansheng

2016-01-01

One debate in mathematical cognition centers on the single-representation model versus the two-representation model. Using an improved number Stroop paradigm (i.e., systematically manipulating physical size distance), in the present study we tested the predictions of the two models for number magnitude processing. The results supported the single-representation model and, more importantly, explained how a design problem (failure to manipulate physical size distance) and an analytical problem (failure to consider the interaction between congruity and task-irrelevant numerical distance) might have contributed to the evidence used to support the two-representation model. This study, therefore, can help settle the debate between the single-representation and two-representation models.

MEMS reliability: The challenge and the promise

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, W.M.; Tanner, D.M.; Miller, S.L.

1998-05-01

MicroElectroMechanical Systems (MEMS) that think, sense, act and communicate will open up a broad new array of cost effective solutions only if they prove to be sufficiently reliable. A valid reliability assessment of MEMS has three prerequisites: (1) statistical significance; (2) a technique for accelerating fundamental failure mechanisms, and (3) valid physical models to allow prediction of failures during actual use. These already exist for the microelectronics portion of such integrated systems. The challenge lies in the less well understood micromachine portions and its synergistic effects with microelectronics. This paper presents a methodology addressing these prerequisites and a description ofmore » the underlying physics of reliability for micromachines.« less

[Depression, social support and compliance in patients with chronic heart failure].

PubMed

Reutlinger, Julia; Müller-Tasch, Thomas; Schellberg, Dieter; Frankenstein, Lutz; Zugck, Christian; Herzog, Wolfgang; Lossnitzer, Nicole

2010-01-01

Depressive patients with chronic heart failure (CHF) show less social integration and greater physical impairment as well as poorer compliance than non depressive CHF patients. Using multiple regression analyses, this study (n=84) investigated a potential mediating effect of depression on the relationship between compliance and both social support and physical functioning. Results did not support the hypothesized mediating effect of depression. However, the variables age, depression, left ventricular ejection fraction (LVEF) and social support were associated with self-reported compliance. Therefore, a lack of social support and depression should be considered as possible reasons, if patients are noncompliant during the treatment process. © Georg Thieme Verlag KG Stuttgart · New York.

Direct modeling parameter signature analysis and failure mode prediction of physical systems using hybrid computer optimization

NASA Technical Reports Server (NTRS)

Drake, R. L.; Duvoisin, P. F.; Asthana, A.; Mather, T. W.

1971-01-01

High speed automated identification and design of dynamic systems, both linear and nonlinear, are discussed. Special emphasis is placed on developing hardware and techniques which are applicable to practical problems. The basic modeling experiment and new results are described. Using the improvements developed successful identification of several systems, including a physical example as well as simulated systems, was obtained. The advantages of parameter signature analysis over signal signature analysis in go-no go testing of operational systems were demonstrated. The feasibility of using these ideas in failure mode prediction in operating systems was also investigated. An improved digital controlled nonlinear function generator was developed, de-bugged, and completely documented.

Improved symptoms, physical limitation, and self-efficacy after resynchronization in a patient with heart failure and a prolonged QRS duration.

PubMed

Conaway, Darcy G; Sullivan, Robbie; McCullough, Peter A

2004-01-01

This report examines the impact of resynchronization therapy in a patient with class IV heart failure and a prolonged QRS duration on electrocardiogram. The Kansas City Cardiomyopathy Questionnaire (KCCQ) was used to assess the patient's health status prior to, immediately after, and 2 months after placement of a biventricular pacemaker. B-type natriuretic peptide (BNP) values and electrocardiogram QRS duration were recorded to further document clinical status. Our patient experienced statistically significant improvements in 7 of 10 KCCQ domains after resynchronization. QRS duration narrowed following the procedure and BNP values decreased. Resynchronization therapy improved this patient's symptoms, physical limitations, and self-efficacy when maximal medical therapy failed.

Erythrocyte Membrane Failure by Electromechanical Stress.

PubMed

Du, E; Qiang, Yuhao; Liu, Jia

2018-01-01

We envision that electrodeformation of biological cells through dielectrophoresis as a new technique to elucidate the mechanistic details underlying membrane failure by electrical and mechanical stresses. Here we demonstrate the full control of cellular uniaxial deformation and tensile recovery in biological cells via amplitude-modified electric field at radio frequency by an interdigitated electrode array in microfluidics. Transient creep and cyclic experiments were performed on individually tracked human erythrocytes. Observations of the viscoelastic-to-viscoplastic deformation behavior and the localized plastic deformations in erythrocyte membranes suggest that electromechanical stress results in irreversible membrane failure. Examples of membrane failure can be separated into different groups according to the loading scenarios: mechanical stiffening, physical damage, morphological transformation from discocyte to echinocyte, and whole cell lysis. These results show that this technique can be potentially utilized to explore membrane failure in erythrocytes affected by other pathophysiological processes.

Burnout and Physical Activity in Minnesota Internal Medicine Resident Physicians

PubMed Central

Olson, Shawn M.; Odo, Nnaemeka U.; Duran, Alisa M.; Pereira, Anne G.; Mandel, Jeffrey H.

2014-01-01

Background Regular physical activity plays an important role in the amelioration of several mental health disorders; however, its relationship with burnout has not yet been clarified. Objective To determine the association between achievement of national physical activity guidelines and burnout in internal medicine resident physicians. Methods A Web-based survey of internal medicine resident physicians at the University of Minnesota and Hennepin County Medical Center was conducted from September to October 2012. Survey measures included the Maslach Burnout Inventory-Human Services Survey and the International Physical Activity Questionnaire. Results Of 149 eligible residents, 76 (51.0%) completed surveys, which were used in the analysis. Burnout prevalence, determined by the Maslach Burnout Inventory, was 53.9% (41 of 76). Prevalence of failure to achieve US Department of Health and Human Services physical activity guidelines was 40.8% (31 of 76), and 78.9% (60 of 76) of residents reported that their level of physical activity has decreased since they began medical training. Residents who were able to meet physical activity guidelines were less likely to be burned out than their fellow residents (OR, 0.38, 95% CI 0.147–0.99). Conclusions Among internal medicine resident physicians, achievement of national physical activity guidelines appears to be inversely associated with burnout. Given the high national prevalence of burnout and inactivity, additional investigation of this relationship appears warranted. PMID:26140116

Robustness of spatial micronetworks

NASA Astrophysics Data System (ADS)

McAndrew, Thomas C.; Danforth, Christopher M.; Bagrow, James P.

2015-04-01

Power lines, roadways, pipelines, and other physical infrastructure are critical to modern society. These structures may be viewed as spatial networks where geographic distances play a role in the functionality and construction cost of links. Traditionally, studies of network robustness have primarily considered the connectedness of large, random networks. Yet for spatial infrastructure, physical distances must also play a role in network robustness. Understanding the robustness of small spatial networks is particularly important with the increasing interest in microgrids, i.e., small-area distributed power grids that are well suited to using renewable energy resources. We study the random failures of links in small networks where functionality depends on both spatial distance and topological connectedness. By introducing a percolation model where the failure of each link is proportional to its spatial length, we find that when failures depend on spatial distances, networks are more fragile than expected. Accounting for spatial effects in both construction and robustness is important for designing efficient microgrids and other network infrastructure.

Cardiac Cachexia: Perspectives for Prevention and Treatment.

PubMed

Okoshi, Marina Politi; Capalbo, Rafael Verardino; Romeiro, Fernando G; Okoshi, Katashi

2017-01-01

Cachexia is a prevalent pathological condition associated with chronic heart failure. Its occurrence predicts increased morbidity and mortality independent of important clinical variables such as age, ventricular function, or heart failure functional class. The clinical consequences of cachexia are dependent on both weight loss and systemic inflammation, which accompany cachexia development. Skeletal muscle wasting is an important component of cachexia; it often precedes cachexia development and predicts poor outcome in heart failure. Cachexia clinically affects several organs and systems. It is a multifactorial condition where underlying pathophysiological mechanisms are not completely understood making it difficult to develop specific prevention and treatment therapies. Preventive strategies have largely focused on muscle mass preservation. Different treatment options have been described, mostly in small clinical studies or experimental settings. These include nutritional support, neurohormonal blockade, reducing intestinal bacterial translocation, anemia and iron deficiency treatment, appetite stimulants, immunomodulatory agents, anabolic hormones, and physical exercise regimens. Currently, nonpharmacological therapy such as nutritional support and physical exercise are considered central to cachexia prevention and treatment.

Electromigration model for the prediction of lifetime based on the failure unit statistics in aluminum metallization

NASA Astrophysics Data System (ADS)

Park, Jong Ho; Ahn, Byung Tae

2003-01-01

A failure model for electromigration based on the "failure unit model" was presented for the prediction of lifetime in metal lines.The failure unit model, which consists of failure units in parallel and series, can predict both the median time to failure (MTTF) and the deviation in the time to failure (DTTF) in Al metal lines. The model can describe them only qualitatively. In our model, both the probability function of the failure unit in single grain segments and polygrain segments are considered instead of in polygrain segments alone. Based on our model, we calculated MTTF, DTTF, and activation energy for different median grain sizes, grain size distributions, linewidths, line lengths, current densities, and temperatures. Comparisons between our results and published experimental data showed good agreements and our model could explain the previously unexplained phenomena. Our advanced failure unit model might be further applied to other electromigration characteristics of metal lines.

Submaximal oxygen uptake kinetics, functional mobility, and physical activity in older adults with heart failure and reduced ejection fraction

PubMed Central

Hummel, Scott L; Herald, John; Alpert, Craig; Gretebeck, Kimberlee A; Champoux, Wendy S; Dengel, Donald R; Vaitkevicius, Peter V; Alexander, Neil B

2016-01-01

Background Submaximal oxygen uptake measures are more feasible and may better predict clinical cardiac outcomes than maximal tests in older adults with heart failure (HF). We examined relationships between maximal oxygen uptake, submaximal oxygen kinetics, functional mobility, and physical activity in older adults with HF and reduced ejection fraction. Methods Older adults with HF and reduced ejection fraction (n = 25, age 75 ± 7 years) were compared to 25 healthy age- and gender-matched controls. Assessments included a maximal treadmill test for peak oxygen uptake (VO2peak), oxygen uptake kinetics at onset of and on recovery from a submaximal treadmill test, functional mobility testing [Get Up and Go (GUG), Comfortable Gait Speed (CGS), Unipedal Stance (US)], and self-reported physical activity (PA). Results Compared to controls, HF had worse performance on GUG, CGS, and US, greater delays in submaximal oxygen uptake kinetics, and lower PA. In controls, VO2peak was more strongly associated with functional mobility and PA than submaximal oxygen uptake kinetics. In HF patients, submaximal oxygen uptake kinetics were similarly associated with GUG and CGS as VO2peak, but weakly associated with PA. Conclusions Based on their mobility performance, older HF patients with reduced ejection fraction are at risk for adverse functional outcomes. In this population, submaximal oxygen uptake measures may be equivalent to VO2 peak in predicting functional mobility, and in addition to being more feasible, may provide better insight into how aerobic function relates to mobility in older adults with HF. PMID:27594875

Submaximal oxygen uptake kinetics, functional mobility, and physical activity in older adults with heart failure and reduced ejection fraction.

PubMed

Hummel, Scott L; Herald, John; Alpert, Craig; Gretebeck, Kimberlee A; Champoux, Wendy S; Dengel, Donald R; Vaitkevicius, Peter V; Alexander, Neil B

2016-07-01

Submaximal oxygen uptake measures are more feasible and may better predict clinical cardiac outcomes than maximal tests in older adults with heart failure (HF). We examined relationships between maximal oxygen uptake, submaximal oxygen kinetics, functional mobility, and physical activity in older adults with HF and reduced ejection fraction. Older adults with HF and reduced ejection fraction (n = 25, age 75 ± 7 years) were compared to 25 healthy age- and gender-matched controls. Assessments included a maximal treadmill test for peak oxygen uptake (VO2peak), oxygen uptake kinetics at onset of and on recovery from a submaximal treadmill test, functional mobility testing [Get Up and Go (GUG), Comfortable Gait Speed (CGS), Unipedal Stance (US)], and self-reported physical activity (PA). Compared to controls, HF had worse performance on GUG, CGS, and US, greater delays in submaximal oxygen uptake kinetics, and lower PA. In controls, VO2peak was more strongly associated with functional mobility and PA than submaximal oxygen uptake kinetics. In HF patients, submaximal oxygen uptake kinetics were similarly associated with GUG and CGS as VO2peak, but weakly associated with PA. Based on their mobility performance, older HF patients with reduced ejection fraction are at risk for adverse functional outcomes. In this population, submaximal oxygen uptake measures may be equivalent to VO2 peak in predicting functional mobility, and in addition to being more feasible, may provide better insight into how aerobic function relates to mobility in older adults with HF.

Comorbid Arthritis Is Associated With Lower Health-Related Quality of Life in Older Adults With Other Chronic Conditions, United States, 2013-2014.

PubMed

Havens, Eric; Slabaugh, S Lane; Helmick, Charles G; Cordier, Tristan; Zack, Matthew; Gopal, Vipin; Prewitt, Todd

2017-07-27

Arthritis is related to poor health-related quality of life (HRQoL) in adults aged 18 years or older. We sought to determine whether this relationship persisted in an older population using claims-based arthritis diagnoses and whether people who also had arthritis and at least 1 of 5 other chronic conditions had lower HRQoL. We identified adults aged 65 years or older with Medicare Advantage coverage in November or December 2014 who responded to an HRQoL survey (Healthy Days). For respondents with and without arthritis, we used linear regression to compare mean physically, mentally, and total unhealthy days, overall and in 5 comorbidity subgroups (coronary artery disease, congestive heart failure, chronic obstructive pulmonary disease, diabetes, and hypertension), accounting for age, sex, dual Medicaid/Medicare eligibility, rural/urban commuting area, and Charlson Comorbidity Index. Of the 58,975 survey respondents, 44% had arthritis diagnosed through claims. Respondents with arthritis reported significantly more adjusted mean physically, mentally, and total unhealthy days than those without arthritis (P < .001). Older adults with arthritis and either congestive heart failure, chronic obstructive pulmonary disease, diabetes, or hypertension reported significantly more adjusted physically, mentally, and total unhealthy days than older adults without arthritis but with the same chronic conditions. In older adults, having arthritis is associated with lower HRQoL and even lower HRQoL among those with at least 1 of 5 other common chronic conditions. Because arthritis is so common among older adults, improving HRQoL depends on managing both underlying chronic conditions and any accompanying arthritis.

The effect of Tai Chi on four chronic conditions-cancer, osteoarthritis, heart failure and chronic obstructive pulmonary disease: a systematic review and meta-analyses.

PubMed

Chen, Yi-Wen; Hunt, Michael A; Campbell, Kristin L; Peill, Kortni; Reid, W Darlene

2016-04-01

Many middle-aged and older persons have more than one chronic condition. Thus, it is important to synthesise the effectiveness of interventions across several comorbidities. The aim of this systematic review was to summarise current evidence regarding the effectiveness of Tai Chi in individuals with four common chronic conditions-cancer, osteoarthritis (OA), heart failure (HF) and chronic obstructive pulmonary disease (COPD). 4 databases (MEDLINE, EMBASE, CINAHL and SPORTDiscus) were searched for original articles. Two reviewers independently screened the titles and abstracts and then conducted full-text reviews, quality assessment and finally data abstraction. 33 studies met the inclusion criteria. Meta-analyses were performed on disease-specific symptoms, physiological outcomes and physical performance of each chronic condition. Subgroup analyses on disease-specific symptoms were conducted by categorising studies into subsets based on the type of comparison groups. Meta-analyses showed that Tai Chi improved or showed a tendency to improve physical performance outcomes, including 6-min walking distance (6MWD) and knee extensor strength, in most or all four chronic conditions. Tai Chi also improved disease-specific symptoms of pain and stiffness in OA. The results demonstrated a favourable effect or tendency of Tai Chi to improve physical performance and showed that this type of exercise could be performed by individuals with different chronic conditions, including COPD, HF and OA. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

A practical review for cardiac rehabilitation professionals of continuous-flow left ventricular assist devices: historical and current perspectives.

PubMed

Compostella, Leonida; Russo, Nicola; Setzu, Tiziana; Bottio, Tomaso; Compostella, Caterina; Tarzia, Vincenzo; Livi, Ugolino; Gerosa, Gino; Iliceto, Sabino; Bellotto, Fabio

2015-01-01

An increasing number of patients with end-stage heart failure are being treated with continuous-flow left ventricular assist devices (cf-LVADs). These patients provide new challenges to the staff in exercise-based cardiac rehabilitation (CR) programs. Even though experience remains limited, it seems that patients supported by cf-LVADs may safely engage in typical rehabilitative activities, provided that some attention is paid to specific aspects, such as the presence of a short external drive line. In spite of initial physical deconditioning, CR allows progressive improvement of symptoms such as fatigue and dyspnea. Intensity of rehabilitative activities should ideally be based on measured aerobic capacity and increased appropriately over time. Regular, long-term exercise training results in improved physical fitness and survival rates. Appropriate adjustment of cf-LVAD settings, together with maintenance of adequate blood volume, provides maximal output, while avoiding suction effects. Ventricular arrhythmias, although not necessarily constituting an immediate life-threatening situation, deserve treatment as they could lead to an increased rate of hospitalization and poorer quality of life. Atrial fibrillation may worsen symptoms of right ventricular failure and reduce exercise tolerance. Blood pressure measurements are possible in cf-LVAD patients only using a Doppler technique, and a mean blood pressure ≤80 mmHg is considered "ideal." Some patients may present with orthostatic intolerance, related to autonomic dysfunction. While exercise training constitutes the basic rehabilitative tool, a comprehensive intervention that includes psychological and social support could better meet the complex needs of patients in which cf-LVAD may offer prolonged survival.

The support-control continuum: An investigation of staff perspectives on factors influencing the success or failure of de-escalation techniques for the management of violence and aggression in mental health settings.

PubMed

Price, Owen; Baker, John; Bee, Penny; Lovell, Karina

2018-01-01

De-escalation techniques are recommended to manage violence and aggression in mental health settings yet restrictive practices continue to be frequently used. Barriers and enablers to the implementation and effectiveness of de-escalation techniques in practice are not well understood. To obtain staff descriptions of de-escalation techniques currently used in mental health settings and explore factors perceived to influence their implementation and effectiveness. Qualitative, semi-structured interviews and Framework Analysis. Five in-patient wards including three male psychiatric intensive care units, one female acute ward and one male acute ward in three UK Mental Health NHS Trusts. 20 ward-based clinical staff. Individual semi-structured interviews were digitally recorded, transcribed verbatim and analysed using a qualitative data analysis software package. Participants described 14 techniques used in response to escalated aggression applied on a continuum between support and control. Techniques along the support-control continuum could be classified in three groups: 'support' (e.g. problem-solving, distraction, reassurance) 'non-physical control' (e.g. reprimands, deterrents, instruction) and 'physical control' (e.g. physical restraint and seclusion). Charting the reasoning staff provided for technique selection against the described behavioural outcome enabled a preliminary understanding of staff, patient and environmental influences on de-escalation success or failure. Importantly, the more coercive 'non-physical control' techniques are currently conceptualised by staff as a feature of de-escalation techniques, yet, there was evidence of a link between these and increased aggression/use of restrictive practices. Risk was not a consistent factor in decisions to adopt more controlling techniques. Moral judgements regarding the function of the aggression; trial-and-error; ingrained local custom (especially around instruction to low stimulus areas); knowledge of the patient; time-efficiency and staff anxiety had a key role in escalating intervention. This paper provides a new model for understanding staff intervention in response to escalated aggression, a continuum between support and control. It further provides a preliminary explanatory framework for understanding the relationship between patient behaviour, staff response and environmental influences on de-escalation success and failure. This framework reveals potentially important behaviour change targets for interventions seeking to reduce violence and use of restrictive practices through enhanced de-escalation techniques. Copyright © 2017 Elsevier Ltd. All rights reserved.

Trajectories of Offending and Their Relation to Life Failure in Late Middle Age: Findings from the Cambridge Study in Delinquent Development

ERIC Educational Resources Information Center

Piquero, Alex R.; Farrington, David P.; Nagin, Daniel S.; Moffitt, Terrie E.

2010-01-01

Researchers have hypothesized that over the life course, criminal offending varies with problems in other domains, including life failure and physical and mental health. To examine this issue, the authors use data from the Cambridge Study in Delinquent Development, a prospective longitudinal survey of 411 South London males first studied at age 8…

A simple landslide susceptibility analysis for hazard and risk assessment in developing countries

NASA Astrophysics Data System (ADS)

Guinau, M.; Vilaplana, J. M.

2003-04-01

In recent years, a number of techniques and methodologies have been developed for mitigating natural disasters. The complexity of these methodologies and the scarcity of material and data series justify the need for simple methodologies to obtain the necessary information for minimising the effects of catastrophic natural phenomena. The work with polygonal maps using a GIS allowed us to develop a simple methodology, which was developed in an area of 473 Km2 in the Departamento de Chinandega (NW Nicaragua). This area was severely affected by a large number of landslides (mainly debris flows), triggered by the Hurricane Mitch rainfalls in October 1998. With the aid of aerial photography interpretation at 1:40.000 scale, amplified to 1:20.000, and detailed field work, a landslide map at 1:10.000 scale was constructed. The failure zones of landslides were digitized in order to obtain a failure zone digital map. A terrain unit digital map, in which a series of physical-environmental terrain factors are represented, was also used. Dividing the studied area into two zones (A and B) with homogeneous physical and environmental characteristics, allows us to develop the proposed methodology and to validate it. In zone A, the failure zone digital map is superimposed onto the terrain unit digital map to establish the relationship between the different terrain factors and the failure zones. The numerical expression of this relationship enables us to classify the terrain by its landslide susceptibility. In zone B, this numerical relationship was employed to obtain a landslide susceptibility map, obviating the need for a failure zone map. The validity of the methodology can be tested in this area by using the degree of superposition of the susceptibility map and the failure zone map. The implementation of the methodology in tropical countries with physical and environmental characteristics similar to those of the study area allows us to carry out a landslide susceptibility analysis in areas where landslide records do not exist. This analysis is essential to landslide hazard and risk assessment, which is necessary to determine the actions for mitigating landslide effects, e.g. land planning, emergency aid actions, etc.

A Framework for Final Drive Simultaneous Failure Diagnosis Based on Fuzzy Entropy and Sparse Bayesian Extreme Learning Machine

PubMed Central

Ye, Qing; Pan, Hao; Liu, Changhua

2015-01-01

This research proposes a novel framework of final drive simultaneous failure diagnosis containing feature extraction, training paired diagnostic models, generating decision threshold, and recognizing simultaneous failure modes. In feature extraction module, adopt wavelet package transform and fuzzy entropy to reduce noise interference and extract representative features of failure mode. Use single failure sample to construct probability classifiers based on paired sparse Bayesian extreme learning machine which is trained only by single failure modes and have high generalization and sparsity of sparse Bayesian learning approach. To generate optimal decision threshold which can convert probability output obtained from classifiers into final simultaneous failure modes, this research proposes using samples containing both single and simultaneous failure modes and Grid search method which is superior to traditional techniques in global optimization. Compared with other frequently used diagnostic approaches based on support vector machine and probability neural networks, experiment results based on F 1-measure value verify that the diagnostic accuracy and efficiency of the proposed framework which are crucial for simultaneous failure diagnosis are superior to the existing approach. PMID:25722717

Nurses' decision making in heart failure management based on heart failure certification status.

PubMed

Albert, Nancy M; Bena, James F; Buxbaum, Denise; Martensen, Linda; Morrison, Shannon L; Prasun, Marilyn A; Stamp, Kelly D

Research findings on the value of nurse certification were based on subjective perceptions or biased by correlations of certification status and global clinical factors. In heart failure, the value of certification is unknown. Examine the value of certification based nurses' decision-making. Cross-sectional study of nurses who completed heart failure clinical vignettes that reflected decision-making in clinical heart failure scenarios. Statistical tests included multivariable linear, logistic and proportional odds logistic regression models. Of nurses (N = 605), 29.1% were heart failure certified, 35.0% were certified in another specialty/job role and 35.9% were not certified. In multivariable modeling, nurses certified in heart failure (versus not heart failure certified) had higher clinical vignette scores (p = 0.002), reflecting higher evidence-based decision making; nurses with another specialty/role certification (versus no certification) did not (p = 0.62). Heart failure certification, but not in other specialty/job roles was associated with decisions that reflected delivery of high-quality care. Copyright © 2018 Elsevier Inc. All rights reserved.

Thermomechanical fatigue life prediction for several solders

NASA Astrophysics Data System (ADS)

Wen, Shengmin

Since solder connections operate at high homologous temperature, solders are high temperature materials. This feature makes their mechanical behavior and fatigue phenomena unique. Based on experimental findings, a physical damage mechanism is introduced for solders. The mechanism views the damage process as a series of independent local damage events characterized by the failure of individual grains, while the structural damage is the eventual percolation result of such local events. Fine's dislocation energy density concept and Mura's microcrack initiation theory are adopted to derive the fatigue formula for an individual grain. A physical damage metric is introduced to describe the material with damage. A unified creep and plasticity constitutive model is adopted to simulate the mechanical behavior of solders. The model is cast into a continuum damage mechanics framework to simulate material with damage. The model gives good agreement with the experimental results of 96.5Pb-3.5Sn and 96.5Sn-3.5Ag solders under uniaxial strain-controlled cyclic loading. The model is convenient for implementation into commercial computational packages. Also presented is a fatigue theory with its failure criterion for solders based on physical damage mechanism. By introducing grain orientation into the fatigue formula, an m-N curve (m is Schmid factor) at constant loading condition is suggested for fatigue of grains with different orientations. A solder structure is defined as fatigued when the damage metric reaches a critical threshold, since at this threshold the failed grains may form a cluster and percolate through the structure according to percolation theory. Fatigue data of 96.5Pb-3.5Sn solder bulk specimens under various uniaxial tension tests were analyzed. Results show that the theory gives consistent predictions under broad conditions, while inelastic strain theory does not. The theory is anisotropic with no size limitation to its application, which could be suitable for anisotropic small-scale (micron or nano scale) solder joints. More importantly, the theory is materials science based so that the parameters of the fatigue formula can be worked out by testing of bulk specimens while the formula can be applicable to small-scale structures. The theory suggests metallurgical control in the manufacturing process to optimize the fatigue life of solder structures.

High-intensity interval exercise training for public health: a big HIT or shall we HIT it on the head?

PubMed

Biddle, Stuart J H; Batterham, Alan M

2015-07-18

The efficacy of high-intensity interval training for a broad spectrum of cardio-metabolic health outcomes is not in question. Rather, the effectiveness of this form of exercise is at stake. In this paper we debate the issues concerning the likely success or failure of high-intensity interval training interventions for population-level health promotion. Biddle maintains that high-intensity interval training cannot be a viable public health strategy as it will not be adopted or maintained by many people. This conclusion is based on an analysis of perceptions of competence, the psychologically aversive nature of high-intensity exercise, the affective component of attitudes, the less conscious elements of motivated behaviour that reflect our likes and dislikes, and analysis using the RE-AIM framework. Batterham argues that this appraisal is based on a constrained and outmoded definition of high-intensity interval training and that truly practical and scalable protocols have been - and continue to be - developed. He contends that the purported displeasure associated with this type of exercise has been overstated. Biddle suggests that the way forward is to help the least active become more active rather than the already active to do more. Batterham claims that traditional physical activity promotion has been a spectacular failure. He proposes that, within an evolutionary health promotion framework, high-intensity interval training could be a successful population strategy for producing rapid physiological adaptations benefiting public health, independent of changes in total physical activity energy expenditure. Biddle recommends that we focus our attention elsewhere if we want population-level gains in physical activity impacting public health. His conclusion is based on his belief that high-intensity interval training interventions will have limited reach, effectiveness, and adoption, and poor implementation and maintenance. In contrast, Batterham maintains that there is genuine potential for scalable, enjoyable high-intensity interval exercise interventions to contribute substantially to addressing areas of public health priority, including prevention and treatment of Type 2 diabetes and cardiovascular disease.

Earthquake Prediction in Large-scale Faulting Experiments

NASA Astrophysics Data System (ADS)

Junger, J.; Kilgore, B.; Beeler, N.; Dieterich, J.

2004-12-01

We study repeated earthquake slip of a 2 m long laboratory granite fault surface with approximately homogenous frictional properties. In this apparatus earthquakes follow a period of controlled, constant rate shear stress increase, analogous to tectonic loading. Slip initiates and accumulates within a limited area of the fault surface while the surrounding fault remains locked. Dynamic rupture propagation and slip of the entire fault surface is induced when slip in the nucleating zone becomes sufficiently large. We report on the event to event reproducibility of loading time (recurrence interval), failure stress, stress drop, and precursory activity. We tentatively interpret these variations as indications of the intrinsic variability of small earthquake occurrence and source physics in this controlled setting. We use the results to produce measures of earthquake predictability based on the probability density of repeating occurrence and the reproducibility of near-field precursory strain. At 4 MPa normal stress and a loading rate of 0.0001 MPa/s, the loading time is ˜25 min, with a coefficient of variation of around 10%. Static stress drop has a similar variability which results almost entirely from variability of the final (rather than initial) stress. Thus, the initial stress has low variability and event times are slip-predictable. The variability of loading time to failure is comparable to the lowest variability of recurrence time of small repeating earthquakes at Parkfield (Nadeau et al., 1998) and our result may be a good estimate of the intrinsic variability of recurrence. Distributions of loading time can be adequately represented by a log-normal or Weibel distribution but long term prediction of the next event time based on probabilistic representation of previous occurrence is not dramatically better than for field-observed small- or large-magnitude earthquake datasets. The gradually accelerating precursory aseismic slip observed in the region of nucleation in these experiments is consistent with observations and theory of Dieterich and Kilgore (1996). Precursory strains can be detected typically after 50% of the total loading time. The Dieterich and Kilgore approach implies an alternative method of earthquake prediction based on comparing real-time strain monitoring with previous precursory strain records or with physically-based models of accelerating slip. Near failure, time to failure t is approximately inversely proportional to precursory slip rate V. Based on a least squares fit to accelerating slip velocity from ten or more events, the standard deviation of the residual between predicted and observed log t is typically 0.14. Scaling these results to natural recurrence suggests that a year prior to an earthquake, failure time can be predicted from measured fault slip rate with a typical error of 140 days, and a day prior to the earthquake with a typical error of 9 hours. However, such predictions require detecting aseismic nucleating strains, which have not yet been found in the field, and on distinguishing earthquake precursors from other strain transients. There is some field evidence of precursory seismic strain for large earthquakes (Bufe and Varnes, 1993) which may be related to our observations. In instances where precursory activity is spatially variable during the interseismic period, as in our experiments, distinguishing precursory activity might be best accomplished with deep arrays of near fault instruments and pattern recognition algorithms such as principle component analysis (Rundle et al., 2000).

Heterogeneity: The key to forecasting material failure?

NASA Astrophysics Data System (ADS)

Vasseur, J.; Wadsworth, F. B.; Lavallée, Y.; Dingwell, D. B.

2014-12-01

Empirical mechanistic models have been applied to the description of the stress and strain rate upon failure for heterogeneous materials. The behaviour of porous rocks and their analogous two-phase viscoelastic suspensions are particularly well-described by such models. Nevertheless, failure cannot yet be predicted forcing a reliance on other empirical prediction tools such as the Failure Forecast Method (FFM). Measurable, accelerating rates of physical signals (e.g., seismicity and deformation) preceding failure are often used as proxies for damage accumulation in the FFM. Previous studies have already statistically assessed the applicability and performance of the FFM, but none (to the best of our knowledge) has done so in terms of intrinsic material properties. Here we use a rheological standard glass, which has been powdered and then sintered for different times (up to 32 hours) at high temperature (675°C) in order to achieve a sample suite with porosities in the range of 0.10-0.45 gas volume fraction. This sample suite was then subjected to mechanical tests in a uniaxial press at a constant strain rate of 10-3 s-1 and a temperature in the region of the glass transition. A dual acoustic emission (AE) rig has been employed to test the success of the FFM in these materials of systematically varying porosity. The pore-emanating crack model describes well the peak stress at failure in the elastic regime for these materials. We show that the FFM predicts failure within 0-15% error at porosities >0.2. However, when porosities are <0.2, the forecast error associated with predicting the failure time increases to >100%. We interpret these results as a function of the low efficiency with which strain energy can be released in the scenario where there are few or no heterogeneities from which cracks can propagate. These observations shed light on questions surrounding the variable efficacy of the FFM applied to active volcanoes. In particular, they provide a systematic demonstration of the fact that a good understanding of the material properties is required. Thus, we wish to emphasize the need for a better coupling of empirical failure forecasting models with mechanical parameters, such as failure criteria for heterogeneous materials, and point to the implications of this for a broad range of material-based disciplines.

The predictive value of physical examination findings in patients with suspected acute heart failure syndrome.

PubMed

Jang, Timothy B; Aubin, Chandra; Naunheim, Rosanne; Lewis, Lawrence M; Kaji, Amy H

2012-06-01

It can be difficult to differentiate acute heart failure syndrome (AHFS) from other causes of acute dyspnea, especially when patients present in extremis. The objective of the study was to determine the predictive value of physical examination findings for pulmonary edema and elevated B-type natriuretic peptide (BNP) levels in patients with suspected AHFS. This was a secondary analysis of a previously reported prospective study of jugular vein ultrasonography in patients with suspected AHFS. Charts were reviewed for physical examination findings, which were then compared to pulmonary edema on chest radiography (CXR) read by radiologists blinded to clinical information and BNP levels measured at presentation. The predictive value of every sign and combination of signs for pulmonary edema on CXR or an elevated BNP was poor. Since physical examination findings alone are not predictive of pulmonary edema or an elevated BNP, clinicians should have a low threshold for using CXR or BNP in clinical evaluation. This brief research report suggests that no physical examination finding or constellation of findings can be used to reliably predict pulmonary edema or an elevated BNP in patients with suspected AHFS.

Collaborative Research. Damage and Burst Dynamics in Failure of Complex Geomaterials. A Statistical Physics Approach to Understanding the Complex Emergent Dynamics in Near Mean-Field Geological Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rundle, John B.; Klein, William

We have carried out research to determine the dynamics of failure in complex geomaterials, specifically focusing on the role of defects, damage and asperities in the catastrophic failure processes (now popularly termed “Black Swan events”). We have examined fracture branching and flow processes using models for invasion percolation, focusing particularly on the dynamics of bursts in the branching process. We have achieved a fundamental understanding of the dynamics of nucleation in complex geomaterials, specifically in the presence of inhomogeneous structures.

The Haunted Inkbottle: Problems of Artistic Communication in Modernism

DTIC Science & Technology

1989-07-07

Whether an artist relates his consciousness to his world--and ultimately to his audience--through physical , intellectual, or spiritual means is the crucial...to his audience--through physical , intellectual, or spiritual means is the crucial factor determining the success or failure of the artist in reaching...the point of physical collapse. Donald Spoto, however, in his biography of the playwright, remarks that company "employment records show that he did

Attributions and self-efficacy for physical activity in multiple sclerosis.

PubMed

Nickel, D; Spink, K; Andersen, M; Knox, K

2014-01-01

Self-efficacy is an important predictor of health-related physical activity in multiple sclerosis (MS). While past experiences are believed to influence efficacy beliefs, the explanations individuals provide for these experiences also may be critical. Our objective was to test the hypothesis that perceived success or failure to accumulate 150 min of physical activity in the previous week would moderate the relationship between the attributional dimension of stability and self-efficacy to exercise in the future. Forty-two adults with MS participated in this cross-sectional descriptive study. Participants completed questions assessing physical activity, perceived outcome for meeting the recommended level of endurance activity, attributions for the outcome, and exercise self-efficacy. Results from hierarchical multiple regression revealed a significant main effect for perceived outcome predicting self-efficacy that was qualified by a significant interaction. The final model, which included perceived outcome, stability, and the interaction term, predicted 37% of the variance in exercise self-efficacy, F (3, 38) = 7.27, p = .001. Our findings suggest that the best prediction of self-efficacy in the MS population may include the interaction of specific attributional dimensions with success/failure at meeting the recommended physical activity dose. Attributions may be another target for interventions aimed at increasing the physical activity in MS.

Comment on ‘Poynting flux in the neighbourhood of a point charge in arbitrary motion and radiative power losses’

NASA Astrophysics Data System (ADS)

Rowland, David R.

2018-01-01

Based on a calculation of the Poynting vector flux in the neighbourhood of an accelerating point charge, Singal (2016 Eur. J. Phys. 37 045210) has claimed that the instantaneous rate of energy radiated by the charge differs from the Larmor formula. It is argued in this comment that Singal’s proposed formula for the radiated power is physically untenable because it predicts a negative rate of energy loss in physically realisable situations. The cause of Singal’s erroneous conclusion is identified as being a failure to realise that the bound electromagnetic field energy of an accelerating charge differs by the Schott energy from the bound field energy of a charge moving at a constant velocity equal to the current velocity of the accelerating charge. References to the salient literature are provided.

Network monitoring in the Tier2 site in Prague

NASA Astrophysics Data System (ADS)

Eliáš, Marek; Fiala, Lukáš; Horký, Jiří; Chudoba, Jiří; Kouba, Tomáš; Kundrát, Jan; Švec, Jan

2011-12-01

Network monitoring provides different types of view on the network traffic. It's output enables computing centre staff to make qualified decisions about changes in the organization of computing centre network and to spot possible problems. In this paper we present network monitoring framework used at Tier-2 in Prague in Institute of Physics (FZU). The framework consists of standard software and custom tools. We discuss our system for hardware failures detection using syslog logging and Nagios active checks, bandwidth monitoring of physical links and analysis of NetFlow exports from Cisco routers. We present tool for automatic detection of network layout based on SNMP. This tool also records topology changes into SVN repository. Adapted weathermap4rrd is used to visualize recorded data to get fast overview showing current bandwidth usage of links in network.

The Caregiver Burden Questionnaire for Heart Failure (CBQ-HF): face and content validity

PubMed Central

2013-01-01

Background A new caregiver burden questionnaire for heart failure (CBQ-HF v1.0) was developed based on previously conducted qualitative interviews with HF caregivers and with input from HF clinical experts. Version 1.0 of the CBQ-HF included 41 items measuring the burden associated with caregiving in the following domains: physical, emotional/psychological, social, and impact on caregiver’s life. Following initial development, the next stage was to evaluate caregivers’ understanding of the questionnaire items and their conceptual relevance. Methods To evaluate the face and content validity of the new questionnaire, cognitive interviews were conducted with caregivers of heart failure patients. The cognitive interviews included a “think aloud” exercise as the patient completed the CBQ-HF, followed by more specific probing questions to better understand caregivers’ understanding, interpretation and the relevance of the instructions, items, response scales and recall period. Results Eighteen caregivers of heart failure patients were recruited. The mean age of the caregivers was 50 years (SD = 10.2). Eighty-three percent of caregivers were female and most commonly the patient was either a spouse (44%) or a parent (28%). Among the patients 55% were NYHA Class 2 and 45% were NYHA Class 3 or 4. The caregiver cognitive interviews demonstrated that the CBQ-HF was well understood, relevant and consistently interpreted. From the initial 41 item questionnaire, fifteen items were deleted due to conceptual overlap and/or item redundancy. The final 26-item CBQ-HF (v3.0) uses a 5-point Likert severity scale, assessing 4 domains of physical, emotional/psychological, social and lifestyle burdens using a 4-week recall period. Conclusions The CBQ-HF (v3.0) is a comprehensive and relevant measure of subjective caregiver burden with strong content validity. This study has established that the CBQ-HF (v3.0) has strong face and content validity and should be valuable as an outcomes measure to help understand and monitor the relationship between patient heart failure severity and caregiver burden. A Translatability AssessmentSM of the measure has since been performed confirming the cultural appropriateness of the measure and psychometric validation is planned for the future to further explore the reliability, and validity of the new questionnaire in a larger caregiver sample. PMID:23706131

Real-time forecasting and predictability of catastrophic failure events: from rock failure to volcanoes and earthquakes

NASA Astrophysics Data System (ADS)

Main, I. G.; Bell, A. F.; Naylor, M.; Atkinson, M.; Filguera, R.; Meredith, P. G.; Brantut, N.

2012-12-01

Accurate prediction of catastrophic brittle failure in rocks and in the Earth presents a significant challenge on theoretical and practical grounds. The governing equations are not known precisely, but are known to produce highly non-linear behavior similar to those of near-critical dynamical systems, with a large and irreducible stochastic component due to material heterogeneity. In a laboratory setting mechanical, hydraulic and rock physical properties are known to change in systematic ways prior to catastrophic failure, often with significant non-Gaussian fluctuations about the mean signal at a given time, for example in the rate of remotely-sensed acoustic emissions. The effectiveness of such signals in real-time forecasting has never been tested before in a controlled laboratory setting, and previous work has often been qualitative in nature, and subject to retrospective selection bias, though it has often been invoked as a basis in forecasting natural hazard events such as volcanoes and earthquakes. Here we describe a collaborative experiment in real-time data assimilation to explore the limits of predictability of rock failure in a best-case scenario. Data are streamed from a remote rock deformation laboratory to a user-friendly portal, where several proposed physical/stochastic models can be analysed in parallel in real time, using a variety of statistical fitting techniques, including least squares regression, maximum likelihood fitting, Markov-chain Monte-Carlo and Bayesian analysis. The results are posted and regularly updated on the web site prior to catastrophic failure, to ensure a true and and verifiable prospective test of forecasting power. Preliminary tests on synthetic data with known non-Gaussian statistics shows how forecasting power is likely to evolve in the live experiments. In general the predicted failure time does converge on the real failure time, illustrating the bias associated with the 'benefit of hindsight' in retrospective analyses. Inference techniques that account explicitly for non-Gaussian statistics significantly reduce the bias, and increase the reliability and accuracy, of the forecast failure time in prospective mode.

Development of a parallel FE simulator for modeling the whole trans-scale failure process of rock from meso- to engineering-scale

NASA Astrophysics Data System (ADS)

Li, Gen; Tang, Chun-An; Liang, Zheng-Zhao

2017-01-01

Multi-scale high-resolution modeling of rock failure process is a powerful means in modern rock mechanics studies to reveal the complex failure mechanism and to evaluate engineering risks. However, multi-scale continuous modeling of rock, from deformation, damage to failure, has raised high requirements on the design, implementation scheme and computation capacity of the numerical software system. This study is aimed at developing the parallel finite element procedure, a parallel rock failure process analysis (RFPA) simulator that is capable of modeling the whole trans-scale failure process of rock. Based on the statistical meso-damage mechanical method, the RFPA simulator is able to construct heterogeneous rock models with multiple mechanical properties, deal with and represent the trans-scale propagation of cracks, in which the stress and strain fields are solved for the damage evolution analysis of representative volume element by the parallel finite element method (FEM) solver. This paper describes the theoretical basis of the approach and provides the details of the parallel implementation on a Windows - Linux interactive platform. A numerical model is built to test the parallel performance of FEM solver. Numerical simulations are then carried out on a laboratory-scale uniaxial compression test, and field-scale net fracture spacing and engineering-scale rock slope examples, respectively. The simulation results indicate that relatively high speedup and computation efficiency can be achieved by the parallel FEM solver with a reasonable boot process. In laboratory-scale simulation, the well-known physical phenomena, such as the macroscopic fracture pattern and stress-strain responses, can be reproduced. In field-scale simulation, the formation process of net fracture spacing from initiation, propagation to saturation can be revealed completely. In engineering-scale simulation, the whole progressive failure process of the rock slope can be well modeled. It is shown that the parallel FE simulator developed in this study is an efficient tool for modeling the whole trans-scale failure process of rock from meso- to engineering-scale.

Free-Swinging Failure Tolerance for Robotic Manipulators

NASA Technical Reports Server (NTRS)

English, James

1997-01-01

Under this GSRP fellowship, software-based failure-tolerance techniques were developed for robotic manipulators. The focus was on failures characterized by the loss of actuator torque at a joint, called free-swinging failures. The research results spanned many aspects of the free-swinging failure-tolerance problem, from preparing for an expected failure to discovery of postfailure capabilities to establishing efficient methods to realize those capabilities. Developed algorithms were verified using computer-based dynamic simulations, and these were further verified using hardware experiments at Johnson Space Center.

Sizing up the Threat: The Envisioned Physical Formidability of Terrorists Tracks Their Leaders' Failures and Successes

ERIC Educational Resources Information Center

Holbrook, Colin; Fessler, Daniel M. T.

2013-01-01

Victory in modern intergroup conflict derives from complex factors, including weaponry, economic resources, tactical outcomes, and leadership. We hypothesize that the mind summarizes such factors into simple metaphorical representations of physical size and strength, concrete dimensions that have determined the outcome of combat throughout both…

Succeed Together or Fail Alone: Going from Good to Great in Physical Education

ERIC Educational Resources Information Center

Pennington, Todd R.; Prusak, Keven A.; Wilkinson, Carol

2014-01-01

"What we have is a systemic failure--one that involves the relationship of physical education programs in public schools with teacher preparation in higher education." (Siedentop & Locke, 1997). This assessment led Prusak, Pennington, Vincent-Graser, Beighle, and Morgan (2010) to an examination of a school district that seemed to…

The Conceptual Foundations of Quantum Mechanics.

ERIC Educational Resources Information Center

Eisenbud, Leonard

This monograph was written for the Conference on the New Instructional Materials in Physics, held at the University of Washington in summer, 1965. It is intended for use by college students at the Junior and Senior levels. There are nine chapters in this monograph. The failure of classical theory in dealing with elementary particles physics is…

Failure, Remediation, and Success in Physical Therapy Clinical Education: Is Mindfulness Present?

ERIC Educational Resources Information Center

Willgens, Annette

2013-01-01

Mindfulness, a purposeful and nonjudgmental awareness of internal affective states, is emerging rapidly in the field of occupational therapy and medicine, but has not yet gained credibility in the education of the physical therapy profession. Some students lack the self-awareness needed to act on professional values, which prevents them from…

Taurine Supplementation Improves Functional Capacity, Myocardial Oxygen Consumption, and Electrical Activity in Heart Failure.

PubMed

Ahmadian, Mehdi; Dabidi Roshan, Valiollah; Ashourpore, Eadeh

2017-07-04

Taurine is an amino acid found abundantly in the heart in very high concentrations. It is assumed that taurine contributes to several physiological functions of mammalian cells, such as osmoregulation, anti-inflammation, membrane stabilization, ion transport modulation, and regulation of oxidative stress and mitochondrial protein synthesis. The objective of the current study was to evaluate the effectiveness of taurine supplementation on functional capacity, myocardial oxygen consumption, and electrical activity in patients with heart failure. In a double-blind and randomly designed study, 16 patients with heart failure were assigned to two groups: taurine (TG, n = 8) and placebo (PG, n = 8). TG received 500-mg taurine supplementation three times per day for two weeks. Significant decrease in the values of Q-T segments (p < 0.01) and significant increase in the values of P-R segments (p < 0.01) were detected following exercise post-supplementation in TG rather than in PG. Significantly higher values of taurine concentration, T wave, Q-T segment, physical capacities, and lower values of cardiovascular capacities were detected post-supplementation in TG as compared with PG (all p values <0.01). Taurine significantly enhanced the physical function and significantly reduced the cardiovascular function parameters following exercise. Our results also suggest that the short-term taurine supplementation is an effective strategy for improving some selected hemodynamic parameters in heart failure patients. Together, these findings support the view that taurine improves cardiac function and functional capacity in patients with heart failure. This idea warrants further study.

Correlation between inner strength and health-promoting behaviors in women with heart failure.

PubMed

Hosseini, Meimanat; Vasli, Parvaneh; Rashidi, Sakineh; Shahsavari, Soodeh

2016-08-01

Inner strength is a factor for mental health and well-being and, consequently, a dynamic component of holistic healing. Health-promoting behaviors are appropriate activities to improve health status and prevent the progression of the functional defect resulting from heart failure. The present study aimed to determine the correlation between inner strength and health-promoting behaviors in women with heart failure referred to hospitals affiliated with Shahid Beheshti University of Medical Sciences (SBMU) in 2013. In this cross-sectional study, 145 women with hearth failure were selected through convenient sampling from the clients referred to hospitals affiliated with SBMU. The data collection tool included a three-section questionnaire of personal characteristics, inner strength, and health-promoting life profile II (HPLP II). The data analysis used descriptive statistical tests and Pearson correlation coefficient through SPSS version 20. A direct significant correlation was found between inner strength and all dimensions of health-promoting behaviors and overall health-promoting behaviors (p=0.000) as well as between all dimensions of inner strength (except for the dimension of knowing and searching with physical activity and the dimension of connectedness with personal accountability in healthcare as well as connectedness with physical activity) with health-promoting behaviors (p=0.000 to p=0008). To improve the level of health and well-being and reduce the costs of care services in women with health failure, close attention should be paid to developing and empowering their inner strength.

Physical properties of conventional and Super Slick elastomeric ligatures after intraoral use.

PubMed

Crawford, Nicola Louise; McCarthy, Caroline; Murphy, Tanya C; Benson, Philip Edward

2010-01-01

To investigate the change in the physical properties of conventional and Super Slick elastomeric ligatures after they have been in the mouth. Nine healthy volunteers took part. One orthodontic bracket was bonded to a premolar tooth in each of the four quadrants of the mouth. Two conventional and two Super Slick elastomeric ligatures were placed at random locations on either side of the mouth. The ligatures were collected after various time intervals and tested using an Instron Universal testing machine. The two outcome measures were failure load and the static frictional resistance. The failure load for conventional ligatures was reduced to 67% of the original value after 6 weeks in situ. Super Slick elastomeric ligatures showed a comparable reduction after 6 weeks in situ (63% of original value). There were no statistical differences in the static friction between conventional and Super Slick elastomerics that had been in situ for either 24 hours (P = .686) or 6 weeks (P = .416). There was a good correlation between failure load and static friction (r = .49). There were statistically significant differences in the failure loads of elastomerics that had not be placed in the mouth and those that had been in the mouth for 6 weeks. There were no differences in the static frictional forces produced by conventional and Super Slick ligatures either before or after they had been placed in the mouth. There appears to be a direct proportional relationship between failure load and static friction of elastomeric ligatures.

Fuzzy Adaptive Compensation Control of Uncertain Stochastic Nonlinear Systems With Actuator Failures and Input Hysteresis.

PubMed

Wang, Jianhui; Liu, Zhi; Chen, C L Philip; Zhang, Yun

2017-10-12

Hysteresis exists ubiquitously in physical actuators. Besides, actuator failures/faults may also occur in practice. Both effects would deteriorate the transient tracking performance, and even trigger instability. In this paper, we consider the problem of compensating for actuator failures and input hysteresis by proposing a fuzzy control scheme for stochastic nonlinear systems. Compared with the existing research on stochastic nonlinear uncertain systems, it is found that how to guarantee a prescribed transient tracking performance when taking into account actuator failures and hysteresis simultaneously also remains to be answered. Our proposed control scheme is designed on the basis of the fuzzy logic system and backstepping techniques for this purpose. It is proven that all the signals remain bounded and the tracking error is ensured to be within a preestablished bound with the failures of hysteretic actuator. Finally, simulations are provided to illustrate the effectiveness of the obtained theoretical results.

Statistical Models of Fracture Relevant to Nuclear-Grade Graphite: Review and Recommendations

NASA Technical Reports Server (NTRS)

Nemeth, Noel N.; Bratton, Robert L.

2011-01-01

The nuclear-grade (low-impurity) graphite needed for the fuel element and moderator material for next-generation (Gen IV) reactors displays large scatter in strength and a nonlinear stress-strain response from damage accumulation. This response can be characterized as quasi-brittle. In this expanded review, relevant statistical failure models for various brittle and quasi-brittle material systems are discussed with regard to strength distribution, size effect, multiaxial strength, and damage accumulation. This includes descriptions of the Weibull, Batdorf, and Burchell models as well as models that describe the strength response of composite materials, which involves distributed damage. Results from lattice simulations are included for a physics-based description of material breakdown. Consideration is given to the predicted transition between brittle and quasi-brittle damage behavior versus the density of damage (level of disorder) within the material system. The literature indicates that weakest-link-based failure modeling approaches appear to be reasonably robust in that they can be applied to materials that display distributed damage, provided that the level of disorder in the material is not too large. The Weibull distribution is argued to be the most appropriate statistical distribution to model the stochastic-strength response of graphite.

Successful treatment of heart failure in an adult patient with Prader-Willi syndrome.

PubMed

Kawano, Hiroaki; Ikeda, Tooru; Shimazaki, Koichi; Arakawa, Shuji; Matsumoto, Yuji; Hayano, Motonobu; Maemura, Koji

2013-01-01

Prader-Willi Syndrome (PWS) is a rare genetic disorder characterized by physical, psychological and physiological abnormalities. Obesity and related cardiovascular diseases are a common problem in adult patients with PWS. This report describes a case of adult PWS with heart failure associated with marked obesity and sleep-disordered breathing that was successfully treated with oxygen therapy, adaptive servoventilation, medications, diet therapy and rehabilitation.

Warrior Injury Assessment Manikin (WIAMan) Lumbar Spine Model Validation: Development, Testing, and Analysis of Physical and Computational Models of the WIAMan Lumbar Spine Materials Demonstrator

DTIC Science & Technology

2016-08-01

load. The 1 and 10 s-1 rate tests were run on a hydraulic high-rate Instron MTS (8821S), placed in a custom- designed tension fixture (Fig. 8...lateral compression prior to shear testing . The sides of the coupon rest on blocks at the bottom of the vice jaw to allow for travel of the center post ...mode of failure based on the lap shear testing . However, since the pretest spine survived all hits at the BRC speeds, it was decided to proceed with

Student Performance in Measuring Distance with Wavelengths in Various Settings

NASA Astrophysics Data System (ADS)

White, Gary

2015-04-01

When physics students are asked to measure the distance between two fixed locations using a pre-defined wavelength as a ruler, there is a surprising failure rate, at least partially due to the fact that the ``ruler'' to be used is not fixed in length (see ``Is a Simple Measurement Task a Roadblock to Student Understanding of Wave Phenomena?,'' by and references therein). I will show some data from introductory classes (algebra- and calculus-based) that replicate this result, and also show some interesting features when comparing a setting involving slinkies with a setting involving surface waves on water.

Incorporating physically-based microstructures in materials modeling: Bridging phase field and crystal plasticity frameworks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lim, Hojun; Abdeljawad, Fadi; Owen, Steven J.

Here, the mechanical properties of materials systems are highly influenced by various features at the microstructural level. The ability to capture these heterogeneities and incorporate them into continuum-scale frameworks of the deformation behavior is considered a key step in the development of complex non-local models of failure. In this study, we present a modeling framework that incorporates physically-based realizations of polycrystalline aggregates from a phase field (PF) model into a crystal plasticity finite element (CP-FE) framework. Simulated annealing via the PF model yields ensembles of materials microstructures with various grain sizes and shapes. With the aid of a novel FEmore » meshing technique, FE discretizations of these microstructures are generated, where several key features, such as conformity to interfaces, and triple junction angles, are preserved. The discretizations are then used in the CP-FE framework to simulate the mechanical response of polycrystalline α-iron. It is shown that the conformal discretization across interfaces reduces artificial stress localization commonly observed in non-conformal FE discretizations. The work presented herein is a first step towards incorporating physically-based microstructures in lieu of the overly simplified representations that are commonly used. In broader terms, the proposed framework provides future avenues to explore bridging models of materials processes, e.g. additive manufacturing and microstructure evolution of multi-phase multi-component systems, into continuum-scale frameworks of the mechanical properties.« less

Incorporating physically-based microstructures in materials modeling: Bridging phase field and crystal plasticity frameworks

DOE PAGES

Lim, Hojun; Abdeljawad, Fadi; Owen, Steven J.; ...

2016-04-25

Here, the mechanical properties of materials systems are highly influenced by various features at the microstructural level. The ability to capture these heterogeneities and incorporate them into continuum-scale frameworks of the deformation behavior is considered a key step in the development of complex non-local models of failure. In this study, we present a modeling framework that incorporates physically-based realizations of polycrystalline aggregates from a phase field (PF) model into a crystal plasticity finite element (CP-FE) framework. Simulated annealing via the PF model yields ensembles of materials microstructures with various grain sizes and shapes. With the aid of a novel FEmore » meshing technique, FE discretizations of these microstructures are generated, where several key features, such as conformity to interfaces, and triple junction angles, are preserved. The discretizations are then used in the CP-FE framework to simulate the mechanical response of polycrystalline α-iron. It is shown that the conformal discretization across interfaces reduces artificial stress localization commonly observed in non-conformal FE discretizations. The work presented herein is a first step towards incorporating physically-based microstructures in lieu of the overly simplified representations that are commonly used. In broader terms, the proposed framework provides future avenues to explore bridging models of materials processes, e.g. additive manufacturing and microstructure evolution of multi-phase multi-component systems, into continuum-scale frameworks of the mechanical properties.« less

Exercise and the cardiovascular system: clinical science and cardiovascular outcomes.

PubMed

Lavie, Carl J; Arena, Ross; Swift, Damon L; Johannsen, Neil M; Sui, Xuemei; Lee, Duck-Chul; Earnest, Conrad P; Church, Timothy S; O'Keefe, James H; Milani, Richard V; Blair, Steven N

2015-07-03

Substantial evidence has established the value of high levels of physical activity, exercise training (ET), and overall cardiorespiratory fitness in the prevention and treatment of cardiovascular diseases. This article reviews some basics of exercise physiology and the acute and chronic responses of ET, as well as the effect of physical activity and cardiorespiratory fitness on cardiovascular diseases. This review also surveys data from epidemiological and ET studies in the primary and secondary prevention of cardiovascular diseases, particularly coronary heart disease and heart failure. These data strongly support the routine prescription of ET to all patients and referrals for patients with cardiovascular diseases, especially coronary heart disease and heart failure, to specific cardiac rehabilitation and ET programs. © 2015 American Heart Association, Inc.

NASA Applications and Lessons Learned in Reliability Engineering

NASA Technical Reports Server (NTRS)

Safie, Fayssal M.; Fuller, Raymond P.

2011-01-01

Since the Shuttle Challenger accident in 1986, communities across NASA have been developing and extensively using quantitative reliability and risk assessment methods in their decision making process. This paper discusses several reliability engineering applications that NASA has used over the year to support the design, development, and operation of critical space flight hardware. Specifically, the paper discusses several reliability engineering applications used by NASA in areas such as risk management, inspection policies, components upgrades, reliability growth, integrated failure analysis, and physics based probabilistic engineering analysis. In each of these areas, the paper provides a brief discussion of a case study to demonstrate the value added and the criticality of reliability engineering in supporting NASA project and program decisions to fly safely. Examples of these case studies discussed are reliability based life limit extension of Shuttle Space Main Engine (SSME) hardware, Reliability based inspection policies for Auxiliary Power Unit (APU) turbine disc, probabilistic structural engineering analysis for reliability prediction of the SSME alternate turbo-pump development, impact of ET foam reliability on the Space Shuttle System risk, and reliability based Space Shuttle upgrade for safety. Special attention is given in this paper to the physics based probabilistic engineering analysis applications and their critical role in evaluating the reliability of NASA development hardware including their potential use in a research and technology development environment.

[Do mastery goals buffer self-esteem from the threat of failure?].

PubMed

Niiya, Yu; Crocker, Jennifer

2007-12-01

Self-esteem is vulnerable when failure occurs in the domain where people base their self-worth (Crocker & Wolfe, 2001). We tested whether learning orientations can reduce the vulnerability of self-esteem associated with contingent self-worth and encourage persistence following failure. Our past research (Niiya, Crocker, & Bartmess, 2004) indicated that people who base their self-worth on academics maintain their self-esteem following failure when they are primed with an incremental theory of intelligence. Our present study extends these findings by (a) examining whether mastery goals (Elliot & Church, 1997) can also buffer self-esteem from failure, (b) using a different manipulation of success and failure, (c) using a different task, and (d) including a measure of persistence. We found that college students who based their self-esteem on academic competence reported lower self-esteem following failure than following success when they had low mastery goals, but the effect of success and failure was eliminated when students had high mastery goals. Moreover, high mastery students showed greater persistence following failure than low mastery students. The study provided converging evidence that learning orientations buffer self-esteem from failure.

Development of biosensors for non-invasive measurements of heart failure biomarkers in saliva

NASA Astrophysics Data System (ADS)

Alcacer, Albert; Streklas, Angelos; Baraket, Abdoullatif; Zine, Nadia; Errachid, Abdelhamid; Bausells, Joan

2017-06-01

Biomedical engineering research today is focused on non-invasive techniques for detection of biomarkers related to specific health issues 1. Three metal layer microelectrode (μE) sensors have been implemented to detect specific biomarkers which can be found in human saliva related with heart failure problems 2 such as interleukin and Tumore Necrosis Factor-α (TNF-α), and used as highly sensitive saliva sensors. We designed specialized μEs combining different technologies for multiple measurements aiming to a lab-on-a-chip future integration. Measurements are based to basic principles of Cyclic Voltammetry (CV) and Electrochemical Impedance Spectroscopy (EIS). Thus, certain planar technology was used involving three metal layers of gold, platinum and silver deposited over an oxidized silicon substrate following standard cleanroom procedures of lithography for the definition of μEs, sputtering physical vapor deposition (PVD) for gold, evaporation PVD for silver and platinum, and plasma enhanced chemical vapor deposition (PECVD) for passivation layer of silicon nitride.

MODELING EXTRAGALACTIC EXTINCTION THROUGH GAMMA-RAY BURST AFTERGLOWS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zonca, Alberto; Mulas, Giacomo; Casu, Silvia

We analyze extragalactic extinction profiles derived through gamma-ray burst afterglows, using a dust model specifically constructed on the assumption that dust grains are not immutable but respond, time-dependently, to the local physics. Such a model includes core-mantle spherical particles of mixed chemical composition (silicate core, sp{sup 2}, and sp{sup 3} carbonaceous layers), and an additional molecular component in the form of free-flying polycyclic aromatic hydrocarbons. We fit most of the observed extinction profiles. Failures occur for lines of sight, presenting remarkable rises blueward of the bump. We find a tendency for the carbon chemical structure to become more aliphatic withmore » the galactic activity, and to some extent with increasing redshifts. Moreover, the contribution of the molecular component to the total extinction is more important in younger objects. The results of the fitting procedure (either successes and failures) may be naturally interpreted through an evolutionary prescription based on the carbon cycle in the interstellar medium of galaxies.« less

The Measurement Of Total Joint Loosening By X-Ray Photogrammetry

NASA Astrophysics Data System (ADS)

Lippert, Frederick G.; Veress, Sandor A.; Tiwari, Rama S.; Harrington, Richard M.

1980-07-01

Failure of total joint replacement due to loosening of the composents either between the implant and cement or between the cement and bone is emerging as a late complication with an incidence as high as 20 percent. Loosening may not only cause pain but progressive loss of support for the prosthesis with eventual structural failure. Early diagnosis is important so that revision may be carried when deterioration or pain occurs. No method is currently available which clearly establishes loosening at an early stage except surgical exploration. We have devised a method based on our in vivo photogrammetry studies of patellar tracking patterns using metallic markers placed in bone near both components of the total joint. Stereo x-rays taken with the joint loaded and unloaded are measured for relative motion between the implant and the metallic markers. Laboratory studies using prosthetic hip components mounted in plastic bone have revealed the ability of this method to detect pistoning movements as small as 80 microns. These findings were confirmed by physical measurements.

Augmenting Probabilistic Risk Assesment with Malevolent Initiators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curtis Smith; David Schwieder

2011-11-01

As commonly practiced, the use of probabilistic risk assessment (PRA) in nuclear power plants only considers accident initiators such as natural hazards, equipment failures, and human error. Malevolent initiators are ignored in PRA, but are considered the domain of physical security, which uses vulnerability assessment based on an officially specified threat (design basis threat). This paper explores the implications of augmenting and extending existing PRA models by considering new and modified scenarios resulting from malevolent initiators. Teaming the augmented PRA models with conventional vulnerability assessments can cost-effectively enhance security of a nuclear power plant. This methodology is useful for operatingmore » plants, as well as in the design of new plants. For the methodology, we have proposed an approach that builds on and extends the practice of PRA for nuclear power plants for security-related issues. Rather than only considering 'random' failures, we demonstrated a framework that is able to represent and model malevolent initiating events and associated plant impacts.« less

Palliative Care in Heart Failure: Rationale, Evidence, and Future Priorities.

PubMed

Kavalieratos, Dio; Gelfman, Laura P; Tycon, Laura E; Riegel, Barbara; Bekelman, David B; Ikejiani, Dara Z; Goldstein, Nathan; Kimmel, Stephen E; Bakitas, Marie A; Arnold, Robert M

2017-10-10

Patients with heart failure (HF) and their families experience stress and suffering from a variety of sources over the course of the HF experience. Palliative care is an interdisciplinary service and an overall approach to care that improves quality of life and alleviates suffering for those living with serious illness, regardless of prognosis. In this review, we synthesize the evidence from randomized clinical trials of palliative care interventions in HF. While the evidence base for palliative care in HF is promising, it is still in its infancy and requires additional high-quality, methodologically sound studies to clearly elucidate the role of palliative care for patients and families living with the burdens of HF. Yet, an increase in attention to primary palliative care (e.g., basic physical and emotional symptom management, advance care planning), provided by primary care and cardiology clinicians, may be a vehicle to address unmet palliative needs earlier and throughout the illness course. Published by Elsevier Inc.

Symptom burden in heart failure: assessment, impact on outcomes, and management.

PubMed

Alpert, Craig M; Smith, Michael A; Hummel, Scott L; Hummel, Ellen K

2017-01-01

Evidence-based management has improved long-term survival in patients with heart failure (HF). However, an unintended consequence of increased longevity is that patients with HF are exposed to a greater symptom burden over time. In addition to classic symptoms such as dyspnea and edema, patients with HF frequently suffer additional symptoms such as pain, depression, gastrointestinal distress, and fatigue. In addition to obvious effects on quality of life, untreated symptoms increase clinical events including emergency department visits, hospitalizations, and long-term mortality in a dose-dependent fashion. Symptom management in patients with HF consists of two key components: comprehensive symptom assessment and sufficient knowledge of available approaches to alleviate the symptoms. Successful treatment addresses not just the physical but also the emotional, social, and spiritual aspects of suffering. Despite a lack of formal experience during cardiovascular training, symptom management in HF can be learned and implemented effectively by cardiology providers. Co-management with palliative medicine specialists can add significant value across the spectrum and throughout the course of HF.

Rupture, waves and earthquakes.

PubMed

Uenishi, Koji

2017-01-01

Normally, an earthquake is considered as a phenomenon of wave energy radiation by rupture (fracture) of solid Earth. However, the physics of dynamic process around seismic sources, which may play a crucial role in the occurrence of earthquakes and generation of strong waves, has not been fully understood yet. Instead, much of former investigation in seismology evaluated earthquake characteristics in terms of kinematics that does not directly treat such dynamic aspects and usually excludes the influence of high-frequency wave components over 1 Hz. There are countless valuable research outcomes obtained through this kinematics-based approach, but "extraordinary" phenomena that are difficult to be explained by this conventional description have been found, for instance, on the occasion of the 1995 Hyogo-ken Nanbu, Japan, earthquake, and more detailed study on rupture and wave dynamics, namely, possible mechanical characteristics of (1) rupture development around seismic sources, (2) earthquake-induced structural failures and (3) wave interaction that connects rupture (1) and failures (2), would be indispensable.

Rupture, waves and earthquakes

PubMed Central

UENISHI, Koji

2017-01-01

Normally, an earthquake is considered as a phenomenon of wave energy radiation by rupture (fracture) of solid Earth. However, the physics of dynamic process around seismic sources, which may play a crucial role in the occurrence of earthquakes and generation of strong waves, has not been fully understood yet. Instead, much of former investigation in seismology evaluated earthquake characteristics in terms of kinematics that does not directly treat such dynamic aspects and usually excludes the influence of high-frequency wave components over 1 Hz. There are countless valuable research outcomes obtained through this kinematics-based approach, but “extraordinary” phenomena that are difficult to be explained by this conventional description have been found, for instance, on the occasion of the 1995 Hyogo-ken Nanbu, Japan, earthquake, and more detailed study on rupture and wave dynamics, namely, possible mechanical characteristics of (1) rupture development around seismic sources, (2) earthquake-induced structural failures and (3) wave interaction that connects rupture (1) and failures (2), would be indispensable. PMID:28077808

A structured analysis of in vitro failure loads and failure modes of fiber, metal, and ceramic post-and-core systems.

PubMed

Fokkinga, Wietske A; Kreulen, Cees M; Vallittu, Pekka K; Creugers, Nico H J

2004-01-01

This study sought to aggregate literature data on in vitro failure loads and failure modes of prefabricated fiber-reinforced composite (FRC) post systems and to compare them to those of prefabricated metal, custom-cast, and ceramic post systems. The literature was searched using MEDLINE from 1984 to 2003 for dental articles in English. Keywords used were (post or core or buildup or dowel) and (teeth or tooth). Additional inclusion/exclusion steps were conducted, each step by two independent readers: (1) Abstracts describing post-and-core techniques to reconstruct endodontically treated teeth and their mechanical and physical characteristics were included (descriptive studies or reviews were excluded); (2) articles that included FRC post systems were selected; (3) in vitro studies, single-rooted human teeth, prefabricated FRC posts, and composite as the core material were the selection criteria; and (4) failure loads and modes were extracted from the selected papers, and failure modes were dichotomized (distinction was made between "favorable failures," defined as reparable failures, and "unfavorable failures,"defined as irreparable [root] fractures). The literature search revealed 1,984 abstracts. Included were 244, 42, and 12 articles in the first, second, and third selection steps, respectively. Custom-cast post systems showed higher failure loads than prefabricated FRC post systems, whereas ceramic showed lower failure loads. Significantly more favorable failures occurred with prefabricated FRC post systems than with prefabricated and custom-cast metal post systems. The variable "post system" had a significant effect on mean failure loads. FRC post systems more frequently showed favorable failure modes than did metal post systems.

Quantification of resilience to water scarcity, a dynamic measure in time and space

NASA Astrophysics Data System (ADS)

Simonovic, S. P.; Arunkumar, R.

2016-05-01

There are practical links between water resources management, climate change adaptation and sustainable development leading to reduction of water scarcity risk and re-enforcing resilience as a new development paradigm. Water scarcity, due to the global change (population growth, land use change and climate change), is of serious concern since it can cause loss of human lives and serious damage to the economy of a region. Unfortunately, in many regions of the world, water scarcity is, and will be unavoidable in the near future. As the scarcity is increasing, at the same time it erodes resilience, therefore global change has a magnifying effect on water scarcity risk. In the past, standard water resources management planning considered arrangements for prevention, mitigation, preparedness and recovery, as well as response. However, over the last ten years substantial progress has been made in establishing the role of resilience in sustainable development. Dynamic resilience is considered as a novel measure that provides for better understanding of temporal and spatial dynamics of water scarcity. In this context, a water scarcity is seen as a disturbance in a complex physical-socio-economic system. Resilience is commonly used as a measure to assess the ability of a system to respond and recover from a failure. However, the time independent static resilience without consideration of variability in space does not provide sufficient insight into system's ability to respond and recover from the failure state and was mostly used as a damage avoidance measure. This paper provides an original systems framework for quantification of resilience. The framework is based on the definition of resilience as the ability of physical and socio-economic systems to absorb disturbance while still being able to continue functioning. The disturbance depends on spatial and temporal perspectives and direct interaction between impacts of disturbance (social, health, economic, and other) and adaptive capacity of the system to absorb disturbance. Utility of the dynamic resilience is demonstrated through a single-purpose reservoir operation subject to different failure (water scarcity) scenarios. The reservoir operation is simulated using the system dynamics (SD) feedback-based object-oriented simulation approach.

CPLOAS_2 user manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sallaberry, Cedric Jean-Marie.; Helton, Jon Craig

2012-10-01

Weak link (WL)/strong link (SL) systems are important parts of the overall operational design of high-consequence systems. In such designs, the SL system is very robust and is intended to permit operation of the entire system under, and only under, intended conditions. In contrast, the WL system is intended to fail in a predictable and irreversible manner under accident conditions and render the entire system inoperable before an accidental operation of the SL system. The likelihood that the WL system will fail to deactivate the entire system before the SL system fails (i.e., degrades into a configuration that could allowmore » an accidental operation of the entire system) is referred to as probability of loss of assured safety (PLOAS). This report describes the Fortran 90 program CPLOAS_2 that implements the following representations for PLOAS for situations in which both link physical properties and link failure properties are time-dependent: (i) failure of all SLs before failure of any WL, (ii) failure of any SL before failure of any WL, (iii) failure of all SLs before failure of all WLs, and (iv) failure of any SL before failure of all WLs. The effects of aleatory uncertainty and epistemic uncertainty in the definition and numerical evaluation of PLOAS can be included in the calculations performed by CPLOAS_2.« less

Pre-configured polyhedron based protection against multi-link failures in optical mesh networks.

PubMed

Huang, Shanguo; Guo, Bingli; Li, Xin; Zhang, Jie; Zhao, Yongli; Gu, Wanyi

2014-02-10

This paper focuses on random multi-link failures protection in optical mesh networks, instead of single, the dual or sequential failures of previous studies. Spare resource efficiency and failure robustness are major concerns in link protection strategy designing and a k-regular and k-edge connected structure is proved to be one of the optimal solutions for link protection network. Based on this, a novel pre-configured polyhedron based protection structure is proposed, and it could provide protection for both simultaneous and sequential random link failures with improved spare resource efficiency. Its performance is evaluated in terms of spare resource consumption, recovery rate and average recovery path length, as well as compared with ring based and subgraph protection under probabilistic link failure scenarios. Results show the proposed novel link protection approach has better performance than previous works.

Buckling failure of square ice-nanotube arrays constrained in graphene nanocapillaries.

PubMed

Zhu, YinBo; Wang, FengChao; Wu, HengAn

2016-08-07

Graphene confinement provides a new physical and mechanical environment with ultrahigh van der Waals pressure, resulting in new quasi-two-dimensional phases of few-layer ice. Polymorphic transition can occur in bilayer constrained water/ice system. Here, we perform a comprehensive study of the phase transition of AA-stacked bilayer water constrained within a graphene nanocapillary. The compression-limit and superheating-limit (phase) diagrams are obtained, based on the extensive molecular-dynamics simulations at numerous thermodynamic states. Liquid-to-solid, solid-to-solid, and solid-to-liquid-to-solid phase transitions are observed in the compression and superheating of bilayer water. Interestingly, there is a temperature threshold (∼275 K) in the compression-limit diagram, which indicates that the first-order and continuous-like phase transitions of bilayer water depend on the temperature. Two obviously different physical processes, compression and superheating, display similar structural evolution; that is, square ice-nanotube arrays (BL-VHDI) will bend first and then transform into bilayer triangular AA stacking ice (BL-AAI). The superheating limit of BL-VHDI exhibits local maxima, while that of BL-AAI increases monotonically. More importantly, from a mechanics point of view, we propose a novel mechanism of the transformation from BL-VHDI to BL-AAI, both for the compression and superheating limits. This structural transformation can be regarded as the "buckling failure" of the square-ice-nanotube columns, which is dominated by the lateral pressure.

Determination of a tissue-level failure evaluation standard for rat femoral cortical bone utilizing a hybrid computational-experimental method.

PubMed

Fan, Ruoxun; Liu, Jie; Jia, Zhengbin; Deng, Ying; Liu, Jun

2018-01-01

Macro-level failure in bone structure could be diagnosed by pain or physical examination. However, diagnosing tissue-level failure in a timely manner is challenging due to the difficulty in observing the interior mechanical environment of bone tissue. Because most fractures begin with tissue-level failure in bone tissue caused by continually applied loading, people attempt to monitor the tissue-level failure of bone and provide corresponding measures to prevent fracture. Many tissue-level mechanical parameters of bone could be predicted or measured; however, the value of the parameter may vary among different specimens belonging to a kind of bone structure even at the same age and anatomical site. These variations cause difficulty in representing tissue-level bone failure. Therefore, determining an appropriate tissue-level failure evaluation standard is necessary to represent tissue-level bone failure. In this study, the yield and failure processes of rat femoral cortical bones were primarily simulated through a hybrid computational-experimental method. Subsequently, the tissue-level strains and the ratio between tissue-level failure and yield strains in cortical bones were predicted. The results indicated that certain differences existed in tissue-level strains; however, slight variations in the ratio were observed among different cortical bones. Therefore, the ratio between tissue-level failure and yield strains for a kind of bone structure could be determined. This ratio may then be regarded as an appropriate tissue-level failure evaluation standard to represent the mechanical status of bone tissue.

Adaptive Crack Modeling with Interface Solid Elements for Plain and Fiber Reinforced Concrete Structures.

PubMed

Zhan, Yijian; Meschke, Günther

2017-07-08

The effective analysis of the nonlinear behavior of cement-based engineering structures not only demands physically-reliable models, but also computationally-efficient algorithms. Based on a continuum interface element formulation that is suitable to capture complex cracking phenomena in concrete materials and structures, an adaptive mesh processing technique is proposed for computational simulations of plain and fiber-reinforced concrete structures to progressively disintegrate the initial finite element mesh and to add degenerated solid elements into the interfacial gaps. In comparison with the implementation where the entire mesh is processed prior to the computation, the proposed adaptive cracking model allows simulating the failure behavior of plain and fiber-reinforced concrete structures with remarkably reduced computational expense.

Adaptive Crack Modeling with Interface Solid Elements for Plain and Fiber Reinforced Concrete Structures

PubMed Central

Zhan, Yijian

2017-01-01

The effective analysis of the nonlinear behavior of cement-based engineering structures not only demands physically-reliable models, but also computationally-efficient algorithms. Based on a continuum interface element formulation that is suitable to capture complex cracking phenomena in concrete materials and structures, an adaptive mesh processing technique is proposed for computational simulations of plain and fiber-reinforced concrete structures to progressively disintegrate the initial finite element mesh and to add degenerated solid elements into the interfacial gaps. In comparison with the implementation where the entire mesh is processed prior to the computation, the proposed adaptive cracking model allows simulating the failure behavior of plain and fiber-reinforced concrete structures with remarkably reduced computational expense. PMID:28773130

Decision Manifold Approximation for Physics-Based Simulations

NASA Technical Reports Server (NTRS)

Wong, Jay Ming; Samareh, Jamshid A.

2016-01-01

With the recent surge of success in big-data driven deep learning problems, many of these frameworks focus on the notion of architecture design and utilizing massive databases. However, in some scenarios massive sets of data may be difficult, and in some cases infeasible, to acquire. In this paper we discuss a trajectory-based framework that quickly learns the underlying decision manifold of binary simulation classifications while judiciously selecting exploratory target states to minimize the number of required simulations. Furthermore, we draw particular attention to the simulation prediction application idealized to the case where failures in simulations can be predicted and avoided, providing machine intelligence to novice analysts. We demonstrate this framework in various forms of simulations and discuss its efficacy.

Understanding the mechanisms leading to failure in metallic nanowire-based transparent heaters, and solution for stability enhancement

NASA Astrophysics Data System (ADS)

Lagrange, M.; Sannicolo, T.; Muñoz-Rojas, D.; Guillo Lohan, B.; Khan, A.; Anikin, M.; Jiménez, C.; Bruckert, F.; Bréchet, Y.; Bellet, D.

2017-02-01

Silver nanowire (AgNW) networks are emerging as one of the most promising alternatives to indium tin oxide (ITO) for transparent electrodes in flexible electronic devices. They can be used in a variety of optoelectronic applications such as solar cells, touch panels and organic light-emitting diodes. Recently they have also proven to be very efficient when used as transparent heaters (THs). In addition to the study of AgNW networks acting as THs in regular use, i.e. at low voltage and moderate temperature, their stability and physical behavior at higher voltages and for longer durations should be studied in view of their integration into real devices. The properties of AgNW networks deposited by spray coating on glass or flexible transparent substrates are thoroughly studied via in situ measurements. The AgNW networks’ behavior at different voltages for different durations and under different atmospheric conditions, both in air and under vacuum, has been examined. At low voltage, a reversible electrical response is observed while irreversibility and even failure are observed at higher voltages. In order to gain a deeper insight into the behavior of AgNW networks used as THs, simple but realistic physical models are proposed and are found to be in fair agreement with the experimental data. Finally, as the stability of AgNW networks is a key issue, we demonstrate that coating AgNW networks with a very thin layer of TiO2 using atomic layer deposition (ALD) improves the material’s resistance against electrical and thermal instabilities without altering optical transmittance. We show that the critical annealing temperature associated to network breakdown increases from 270 °C for the as-deposited AgNW networks to 420 °C for AgNW networks coated with TiO2. Similarly, the electrical failure which occurs at 7 V for the as-deposited networks increases to 13 V for TiO2-coated networks. TiO2 is also proved to stabilize AgNW networks during long duration operation and at high voltage. Temperature higher than 235 °C was achieved at 7 V without failure.

Real-time diagnostics of the reusable rocket engine using on-line system identification

NASA Technical Reports Server (NTRS)

Guo, T.-H.; Merrill, W.; Duyar, A.

1990-01-01

A model-based failure diagnosis system has been proposed for real-time diagnosis of SSME failures. Actuation, sensor, and system degradation failure modes are all considered by the proposed system. In the case of SSME actuation failures, it was shown that real-time identification can effectively be used for failure diagnosis purposes. It is a direct approach since it reduces the detection, isolation, and the estimation of the extent of the failures to the comparison of parameter values before and after the failure. As with any model-based failure detection system, the proposed approach requires a fault model that embodies the essential characteristics of the failure process. The proposed diagnosis approach has the added advantage that it can be used as part of an intelligent control system for failure accommodation purposes.

Free-Swinging Failure Tolerance for Robotic Manipulators. Degree awarded by Purdue Univ.

NASA Technical Reports Server (NTRS)

English, James

1997-01-01

Under this GSRP fellowship, software-based failure-tolerance techniques were developed for robotic manipulators. The focus was on failures characterized by the loss of actuator torque at a joint, called free-swinging failures. The research results spanned many aspects of the free-swinging failure-tolerance problem, from preparing for an expected failure to discovery of postfailure capabilities to establishing efficient methods to realize those capabilities. Developed algorithms were verified using computer-based dynamic simulations, and these were further verified using hardware experiments at Johnson Space Center.

Adaptive Failure Compensation for Aircraft Tracking Control Using Engine Differential Based Model

NASA Technical Reports Server (NTRS)

Liu, Yu; Tang, Xidong; Tao, Gang; Joshi, Suresh M.

2006-01-01

An aircraft model that incorporates independently adjustable engine throttles and ailerons is employed to develop an adaptive control scheme in the presence of actuator failures. This model captures the key features of aircraft flight dynamics when in the engine differential mode. Based on this model an adaptive feedback control scheme for asymptotic state tracking is developed and applied to a transport aircraft model in the presence of two types of failures during operation, rudder failure and aileron failure. Simulation results are presented to demonstrate the adaptive failure compensation scheme.

Torsion Tests of Tubes

NASA Technical Reports Server (NTRS)

Stang, Ambrose H; Ramberg, Walter; Back, Goldie

1937-01-01

This report presents the results of tests of 63 chromium-molybdenum steel tubes and 102 17st aluminum-alloy tubes of various sizes and lengths made to study the dependence of the torsional strength on both the dimensions of the tube and the physical properties of the tube material. Three types of failure are found to be important for sizes of tubes frequently used in aircraft construction: (1) failure by plastic shear, in which the tube material reached its yield strength before the critical torque was reached; (2) failure by elastic two-lobe buckling, which depended only on the elastic properties of the tube material and the dimensions of the tube; and (3) failure by a combination of (1) and (2) that is, by buckling taking place after some yielding of the tube material.

Field Programmable Gate Array Failure Rate Estimation Guidelines for Launch Vehicle Fault Tree Models

NASA Technical Reports Server (NTRS)

Al Hassan, Mohammad; Britton, Paul; Hatfield, Glen Spencer; Novack, Steven D.

2017-01-01

Today's launch vehicles complex electronic and avionics systems heavily utilize Field Programmable Gate Array (FPGA) integrated circuits (IC) for their superb speed and reconfiguration capabilities. Consequently, FPGAs are prevalent ICs in communication protocols such as MILSTD- 1553B and in control signal commands such as in solenoid valve actuations. This paper will identify reliability concerns and high level guidelines to estimate FPGA total failure rates in a launch vehicle application. The paper will discuss hardware, hardware description language, and radiation induced failures. The hardware contribution of the approach accounts for physical failures of the IC. The hardware description language portion will discuss the high level FPGA programming languages and software/code reliability growth. The radiation portion will discuss FPGA susceptibility to space environment radiation.

Shapeable short circuit resistant capacitor

DOEpatents

Taylor, Ralph S.; Myers, John D.; Baney, William J.

2015-10-06

A ceramic short circuit resistant capacitor that is bendable and/or shapeable to provide a multiple layer capacitor that is extremely compact and amenable to desirable geometries. The capacitor that exhibits a benign failure mode in which a multitude of discrete failure events result in a gradual loss of capacitance. Each event is a localized event in which localized heating causes an adjacent portion of one or both of the electrodes to vaporize, physically cleaning away electrode material from the failure site. A first metal electrode, a second metal electrode, and a ceramic dielectric layer between the electrodes are thin enough to be formed in a serpentine-arrangement with gaps between the first electrode and the second electrode that allow venting of vaporized electrode material in the event of a benign failure.

Forecasting overhaul or replacement intervals based on estimated system failure intensity

NASA Astrophysics Data System (ADS)

Gannon, James M.

1994-12-01

System reliability can be expressed in terms of the pattern of failure events over time. Assuming a nonhomogeneous Poisson process and Weibull intensity function for complex repairable system failures, the degree of system deterioration can be approximated. Maximum likelihood estimators (MLE's) for the system Rate of Occurrence of Failure (ROCOF) function are presented. Evaluating the integral of the ROCOF over annual usage intervals yields the expected number of annual system failures. By associating a cost of failure with the expected number of failures, budget and program policy decisions can be made based on expected future maintenance costs. Monte Carlo simulation is used to estimate the range and the distribution of the net present value and internal rate of return of alternative cash flows based on the distributions of the cost inputs and confidence intervals of the MLE's.

Risk-based planning analysis for a single levee

NASA Astrophysics Data System (ADS)

Hui, Rui; Jachens, Elizabeth; Lund, Jay

2016-04-01

Traditional risk-based analysis for levee planning focuses primarily on overtopping failure. Although many levees fail before overtopping, few planning studies explicitly include intermediate geotechnical failures in flood risk analysis. This study develops a risk-based model for two simplified levee failure modes: overtopping failure and overall intermediate geotechnical failure from through-seepage, determined by the levee cross section represented by levee height and crown width. Overtopping failure is based only on water level and levee height, while through-seepage failure depends on many geotechnical factors as well, mathematically represented here as a function of levee crown width using levee fragility curves developed from professional judgment or analysis. These levee planning decisions are optimized to minimize the annual expected total cost, which sums expected (residual) annual flood damage and annualized construction costs. Applicability of this optimization approach to planning new levees or upgrading existing levees is demonstrated preliminarily for a levee on a small river protecting agricultural land, and a major levee on a large river protecting a more valuable urban area. Optimized results show higher likelihood of intermediate geotechnical failure than overtopping failure. The effects of uncertainty in levee fragility curves, economic damage potential, construction costs, and hydrology (changing climate) are explored. Optimal levee crown width is more sensitive to these uncertainties than height, while the derived general principles and guidelines for risk-based optimal levee planning remain the same.

Natriuretic Peptide and Clinical Evaluation in the Diagnosis of Heart Failure Hemodynamic Profile: Comparison with Tissue Doppler Echocardiography.

PubMed

Almeida Junior, Gustavo Luiz Gouvêa de; Clausell, Nadine; Garcia, Marcelo Iorio; Esporcatte, Roberto; Rangel, Fernando Oswaldo Dias; Rocha, Ricardo Mourilhe; Beck-da-Silva, Luis; Silva, Fabricio Braga da; Gorgulho, Paula de Castro Carvalho; Xavier, Sergio Salles

2018-03-01

Physical examination and B-type natriuretic peptide (BNP) have been used to estimate hemodynamics and tailor therapy of acute decompensated heart failure (ADHF) patients. However, correlation between these parameters and left ventricular filling pressures is controversial. This study was designed to evaluate the diagnostic accuracy of physical examination, chest radiography (CR) and BNP in estimating left atrial pressure (LAP) as assessed by tissue Doppler echocardiogram. Patients admitted with ADHF were prospectively assessed. Diagnostic characteristics of physical signs of heart failure, CR and BNP in predicting elevation (> 15 mm Hg) of LAP, alone or combined, were calculated. Spearman test was used to analyze the correlation between non-normal distribution variables. The level of significance was 5%. Forty-three patients were included, with mean age of 69.9 ± 11.1years, left ventricular ejection fraction of 25 ± 8.0%, and BNP of 1057 ± 1024.21 pg/mL. Individually, all clinical, CR or BNP parameters had a poor performance in predicting LAP ≥ 15 mm Hg. A clinical score of congestion had the poorest performance [area under the receiver operating characteristic curve (AUC) 0.53], followed by clinical score + CR (AUC 0.60), clinical score + CR + BNP > 400 pg/mL (AUC 0.62), and clinical score + CR + BNP > 1000 pg/mL (AUC 0.66). Physical examination, CR and BNP had a poor performance in predicting a LAP ≥ 15 mm Hg. Using these parameters alone or in combination may lead to inaccurate estimation of hemodynamics.

How do cardiorespiratory fitness improvements vary with physical training modality in heart failure patients? A quantitative guide

PubMed Central

Smart, Neil A

2013-01-01

BACKGROUND: Peak oxygen consumption (VO2) is the gold standard measure of cardiorespiratory fitness and a reliable predictor of survival in chronic heart failure patients. Furthermore, any form of physical training usually improves cardiorespiratory fitness, although the magnitude of improvement in peak VO2 may vary across different training prescriptions. OBJECTIVE: To quantify, and subsequently rank, the magnitude of improvement in peak VO2 for different physical training prescriptions using data from published meta-analyses and randomized controlled trials. METHODS: Prospective randomized controlled parallel trials and meta-analyses of exercise training in chronic heart failure patients that provided data on change in peak VO2 for nine a priori comparative analyses were examined. RESULTS: All forms of physical training were beneficial, although the improvement in peak VO2 varied with modality. High-intensity interval exercise yielded the largest increase in peak VO2, followed in descending order by moderate-intensity aerobic exercise, functional electrical stimulation, inspiratory muscle training, combined aerobic and resistance training, and isolated resistance training. With regard to setting, the present study was unable to determine whether outpatient or unsupervised home exercise provided greater benefits in terms of peak VO2 improvment. CONCLUSIONS: Interval exercise is not suitable for all patients, especially the high-intensity variety; however, when indicated, this form of exercise should be adopted to optimize peak VO2 adaptations. Other forms of activity, such as functional electrical stimulation, may be more appropriate for patients who are not capable of high-intensity interval training, especially for severely deconditioned patients who are initially unable to exercise. PMID:24294043

Creating a model of diseased artery damage and failure from healthy porcine aorta.

PubMed

Noble, Christopher; Smulders, Nicole; Green, Nicola H; Lewis, Roger; Carré, Matt J; Franklin, Steve E; MacNeil, Sheila; Taylor, Zeike A

2016-07-01

Large quantities of diseased tissue are required in the research and development of new generations of medical devices, for example for use in physical testing. However, these are difficult to obtain. In contrast, porcine arteries are readily available as they are regarded as waste. Therefore, reliable means of creating from porcine tissue physical models of diseased human tissue that emulate well the associated mechanical changes would be valuable. To this end, we studied the effect on mechanical response of treating porcine thoracic aorta with collagenase, elastase and glutaraldehyde. The alterations in mechanical and failure properties were assessed via uniaxial tension testing. A constitutive model composed of the Gasser-Ogden-Holzapfel model, for elastic response, and a continuum damage model, for the failure, was also employed to provide a further basis for comparison (Calvo and Peña, 2006; Gasser et al., 2006). For the concentrations used here it was found that: collagenase treated samples showed decreased fracture stress in the axial direction only; elastase treated samples showed increased fracture stress in the circumferential direction only; and glutaraldehyde samples showed no change in either direction. With respect to the proposed constitutive model, both collagenase and elastase had a strong effect on the fibre-related terms. The model more closely captured the tissue response in the circumferential direction, due to the smoother and sharper transition from damage initiation to complete failure in this direction. Finally, comparison of the results with those of tensile tests on diseased tissues suggests that these treatments indeed provide a basis for creation of physical models of diseased arteries. Copyright © 2016 Elsevier Ltd. All rights reserved.

WE-G-BRC-03: Risk Assessment for Physics Plan Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parker, S.

2016-06-15

Failure Mode and Effects Analysis (FMEA) originated as an industrial engineering technique used for risk management and safety improvement of complex processes. In the context of radiotherapy, the AAPM Task Group 100 advocates FMEA as the framework of choice for establishing clinical quality management protocols. However, there is concern that widespread adoption of FMEA in radiation oncology will be hampered by the perception that implementation of the tool will have a steep learning curve, be extremely time consuming and labor intensive, and require additional resources. To overcome these preconceptions and facilitate the introduction of the tool into clinical practice, themore » medical physics community must be educated in the use of this tool and the ease in which it can be implemented. Organizations with experience in FMEA should share their knowledge with others in order to increase the implementation, effectiveness and productivity of the tool. This session will include a brief, general introduction to FMEA followed by a focus on practical aspects of implementing FMEA for specific clinical procedures including HDR brachytherapy, physics plan review and radiosurgery. A description of common equipment and devices used in these procedures and how to characterize new devices for safe use in patient treatments will be presented. This will be followed by a discussion of how to customize FMEA techniques and templates to one’s own clinic. Finally, cases of common failure modes for specific procedures (described previously) will be shown and recommended intervention methodologies and outcomes reviewed. Learning Objectives: Understand the general concept of failure mode and effect analysis Learn how to characterize new equipment for safety Be able to identify potential failure modes for specific procedures and learn mitigation techniques Be able to customize FMEA examples and templates for use in any clinic.« less

Multivariate analysis of fears in dental phobic patients according to a reduced FSS-II scale.

PubMed

Hakeberg, M; Gustafsson, J E; Berggren, U; Carlsson, S G

1995-10-01

This study analyzed and assessed dimensions of a questionnaire developed to measure general fears and phobias. A previous factor analysis among 109 dental phobics had revealed a five-factor structure with 22 items and an explained total variance of 54%. The present study analyzed the same material using a multivariate statistical procedure (LISREL) to reveal structural latent variables. The LISREL analysis, based on the correlation matrix, yielded a chi-square of 216.6 with 195 degrees of freedom (P = 0.138) and showed a model with seven latent variables. One was a general fear factor correlated to all 22 items. The other six factors concerned "Illness & Death" (5 items), "Failures & Embarrassment" (5 items), "Social situations" (5 items), "Physical injuries" (4 items), "Animals & Natural phenomena" (4 items). One item (opposite sex) was included in both "Failures & Embarrassment" and "Social situations". The last factor, "Social interaction", combined all the items in "Failures & Embarrassment" and "Social situations" (9 items). In conclusion, this multivariate statistical analysis (LISREL) revealed and confirmed a factor structure similar to our previous study, but added two important dimensions not shown with a traditional factor analysis. This reduced FSS-II version measures general fears and phobias and may be used on a routine clinical basis as well as in dental phobia research.

An introductory review on gravitational-deformation induced structures, fabrics and modeling

NASA Astrophysics Data System (ADS)

Jaboyedoff, Michel; Penna, Ivanna; Pedrazzini, Andrea; Baroň, Ivo; Crosta, Giovanni B.

2013-10-01

Recent studies have pointed out a similarity between tectonics and slope tectonic-induced structures. Numerous studies have demonstrated that structures and fabrics previously interpreted as of purely geodynamical origin are instead the result of large slope deformation, and this led in the past to erroneous interpretations. Nevertheless, their limit seems not clearly defined, but it is somehow transitional. Some studies point out continuity between failures developing at surface with upper crust movements. In this contribution, the main studies which examine the link between rock structures and slope movements are reviewed. The aspects regarding model and scale of observation are discussed together with the role of pre-existing weaknesses in the rock mass. As slope failures can develop through progressive failure, structures and their changes in time and space can be recognized. Furthermore, recognition of the origin of these structures can help in avoiding misinterpretations of regional geology. This also suggests the importance of integrating different slope movement classifications based on distribution and pattern of deformation and the application of structural geology techniques. A structural geology approach in the landslide community is a tool that can greatly support the hazard quantification and related risks, because most of the physical parameters, which are used for landslide modeling, are derived from geotechnical tests or the emerging geophysical approaches.

Gender differences in patients with heart failure.

PubMed

Strömberg, Anna; Mårtensson, Jan

2003-04-01

The aim of this literature review was to review and discuss the differences between men and women with heart failure with regard to epidemiology, aetiology, diagnostics, prognosis, pharmacological and non-pharmacological treatment, and the impact of heart failure on psychosocial factors and healthcare utilisation. Two primary health care resources, MEDLINE and CINAHL, were selected to review the current literature. In MEDLINE, 234 abstracts dealing with heart failure and gender/sex were found and in CINAHL, 20 abstracts. Men have a higher incidence of heart failure, but the overall prevalence rate is similar in both sexes, since women survive longer after the onset of heart failure. Women tend to be older when diagnosed with heart failure and more often have diastolic dysfunction than men. The extent of sex differences in treatment, hospital cost and quality of care can partly be explained by age differences. The life situations for men and women with heart failure are different. Physical and social restrictions affecting daily life activities are experienced as most bothersome for men, whereas restrictions affecting the possibility to support family and friends are most difficult to accept for women. Women with heart failure ascribe more positive meanings to their illness. Despite this, women seem to experience a lower overall quality of life than men. The known gender differences in patients with heart failure need to be highlighted in guidelines as well as implemented in standard care.

Probability of loss of assured safety in systems with multiple time-dependent failure modes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helton, Jon Craig; Pilch, Martin.; Sallaberry, Cedric Jean-Marie.

2012-09-01

Weak link (WL)/strong link (SL) systems are important parts of the overall operational design of high-consequence systems. In such designs, the SL system is very robust and is intended to permit operation of the entire system under, and only under, intended conditions. In contrast, the WL system is intended to fail in a predictable and irreversible manner under accident conditions and render the entire system inoperable before an accidental operation of the SL system. The likelihood that the WL system will fail to deactivate the entire system before the SL system fails (i.e., degrades into a configuration that could allowmore » an accidental operation of the entire system) is referred to as probability of loss of assured safety (PLOAS). Representations for PLOAS for situations in which both link physical properties and link failure properties are time-dependent are derived and numerically evaluated for a variety of WL/SL configurations, including PLOAS defined by (i) failure of all SLs before failure of any WL, (ii) failure of any SL before failure of any WL, (iii) failure of all SLs before failure of all WLs, and (iv) failure of any SL before failure of all WLs. The effects of aleatory uncertainty and epistemic uncertainty in the definition and numerical evaluation of PLOAS are considered.« less

Project Physics Reader 5, Models of the Atom.

ERIC Educational Resources Information Center

Harvard Univ., Cambridge, MA. Harvard Project Physics.

As a supplement to Project Physics Unit 5, a collection of articles is presented in this reader for student browsing. Nine excerpts are given under the following headings: failure and success, Einstein, Mr. Tompkins and simultaneity, parable of the surveyors, outside and inside the elevator, the teacher and the Bohr theory of atom, Dirac and Born,…

Physical Education Teacher Education in Norway: The Perceptions of Student Teachers

ERIC Educational Resources Information Center

Mordal-Moen, Kjersti; Green, Ken

2014-01-01

A feature of academic literature on physical education teacher education (PETE) is the expectation that it can and should impact upon student teachers' beliefs and prospective practices in some significant ways. This is despite research over the last 20 years or more alluding to the apparent failure of PETE to "shake or stir" (Evans et…

Exercise and College Students: How Regular Exercise Contributes to Approach Motivation via Self-Efficacy

ERIC Educational Resources Information Center

Weinkauff Duranso, Christine M.

2017-01-01

There is evidence that participating in physical exercise reduces stress and the risk of many physical maladies. Exercise is also correlated with higher levels of approach motivation, or a tendency to approach challenge as an opportunity for growth or improvement instead of an opportunity for failure. To date, most research on this relationship…

Reformulation of Nonlinear Anisotropic Crystal Elastoplasticity for Impact Physics

DTIC Science & Technology

2015-03-01

interest include metals, ceramics , minerals, and energetic materials . Accurate, efficient, stable, and thermodynamically consistent models for...Clayton JD. Phase field theory and analysis of pressure-shear induced amorphization and failure in boron carbide ceramic . AIMS Materials Science. 2014;1...of Nonlinear Anisotropic Crystal Elastoplasticity for Impact Physics by JD Clayton Weapons and Materials Research Directorate, ARL

"Pursuing a Lifetime of Healthful Physical Activity" through Falling and Rolling

ERIC Educational Resources Information Center

Kozub, Francis M.; Hogan, John T.

2013-01-01

The basic movement concepts associated with falling and rolling are needed for many dynamic adult activities. This is the case any time the activity, either by intent or accident, involves safely transitioning from a standing position to the ground quickly. Failure to teach these skills in school physical education could result in a barrier to…

Electrical failure debug using interlayer profiling method

NASA Astrophysics Data System (ADS)

Yang, Thomas; Shen, Yang; Zhang, Yifan; Sweis, Jason; Lai, Ya-Chieh

2017-03-01

It is very well known that as technology nodes move to smaller sizes, the number of design rules increases while design structures become more regular and the process manufacturing steps have increased as well. Normal inspection tools can only monitor hard failures on a single layer. For electrical failures that happen due to inter layers misalignments, we can only detect them through testing. This paper will present a working flow for using pattern analysis interlayer profiling techniques to turn multiple layer physical info into group linked parameter values. Using this data analysis flow combined with an electrical model allows us to find critical regions on a layout for yield learning.

Sensitivity to VSR failure: K pipe break accident

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meichle, R.H.

1969-09-12

Reactor effects of failure of a safety rod to scram can be considered in two major respects: The reduction in total safety system strength which will affect the amount of ``prompt drop`` and subsequent flux decay rate of the average neutron flux-level; and the change in local flux distribution due to the absence of the particular rod which fails to enter the reactor. The purpose of this memorandum is to describe the physical effects involved and to indicate the approximate magnitude of both reactor-wide and localized changes in event of failure of a VSR simultaneous with a K Reactor risermore » accident.« less

HDL-cholesterol and physical performance: results from the ageing and longevity study in the sirente geographic area (ilSIRENTE Study).

PubMed

Landi, Francesco; Russo, Andrea; Cesari, Matteo; Pahor, Marco; Bernabei, Roberto; Onder, Graziano

2007-09-01

High-density lipoprotein (HDL) cholesterol has been hypothesised to be a reliable marker of frailty and poor prognosis among the oldest elderly. We evaluate the relationship of HDL-cholesterol with measures of physical performance, muscle strength, and functional status in older persons aged 80years or older. Data are from baseline evaluation of the ageing and longevity study in the Sirente geographic area (ilSIRENTE study) (n = 364). Physical performance was assessed using the physical performance battery score [short physical performance battery (SPPB)], which is based on three-timed tests: 4-m walking-speed, balance, and chair-stand tests. Muscle strength was measured by hand-grip strength. Analyses of covariance were performed to evaluate the relationship of different HDL-cholesterol levels with physical function. In the unadjusted analyses, physical function (as measured by the 4-m walking-speed, theSPPB score, the basic and instrumental activities of daily living scales scores), but not hand-grip strength, improved significantly as HDL-cholesterol tertiles increased. After adjustment for potential confounders, which included age, gender, living alone, alcohol abuse, physical activity, congestive heart failure, diabetes, cerebrovascular diseases, osteoarthritis, albumin, urea, C-reactive protein and LDL cholesterol, the association of HDL-cholesterol tertiles with the 4-m walking-speed and the SPPB score was still consistent. The present study suggests that among very old subjects living in the community the higher levels of HDL-cholesterol are associated with better functional performance.

WE-H-BRC-09: Simulated Errors in Mock Radiotherapy Plans to Quantify the Effectiveness of the Physics Plan Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gopan, O; Kalet, A; Smith, W

2016-06-15

Purpose: A standard tool for ensuring the quality of radiation therapy treatments is the initial physics plan review. However, little is known about its performance in practice. The goal of this study is to measure the effectiveness of physics plan review by introducing simulated errors into “mock” treatment plans and measuring the performance of plan review by physicists. Methods: We generated six mock treatment plans containing multiple errors. These errors were based on incident learning system data both within the department and internationally (SAFRON). These errors were scored for severity and frequency. Those with the highest scores were included inmore » the simulations (13 errors total). Observer bias was minimized using a multiple co-correlated distractor approach. Eight physicists reviewed these plans for errors, with each physicist reviewing, on average, 3/6 plans. The confidence interval for the proportion of errors detected was computed using the Wilson score interval. Results: Simulated errors were detected in 65% of reviews [51–75%] (95% confidence interval [CI] in brackets). The following error scenarios had the highest detection rates: incorrect isocenter in DRRs/CBCT (91% [73–98%]) and a planned dose different from the prescribed dose (100% [61–100%]). Errors with low detection rates involved incorrect field parameters in record and verify system (38%, [18–61%]) and incorrect isocenter localization in planning system (29% [8–64%]). Though pre-treatment QA failure was reliably identified (100%), less than 20% of participants reported the error that caused the failure. Conclusion: This is one of the first quantitative studies of error detection. Although physics plan review is a key safety measure and can identify some errors with high fidelity, others errors are more challenging to detect. This data will guide future work on standardization and automation. Creating new checks or improving existing ones (i.e., via automation) will help in detecting those errors with low detection rates.« less

Advanced Ground Systems Maintenance Physics Models For Diagnostics Project

NASA Technical Reports Server (NTRS)

Perotti, Jose M.

2015-01-01

The project will use high-fidelity physics models and simulations to simulate real-time operations of cryogenic and systems and calculate the status/health of the systems. The project enables the delivery of system health advisories to ground system operators. The capability will also be used to conduct planning and analysis of cryogenic system operations. This project will develop and implement high-fidelity physics-based modeling techniques tosimulate the real-time operation of cryogenics and other fluids systems and, when compared to thereal-time operation of the actual systems, provide assessment of their state. Physics-modelcalculated measurements (called “pseudo-sensors”) will be compared to the system real-timedata. Comparison results will be utilized to provide systems operators with enhanced monitoring ofsystems' health and status, identify off-nominal trends and diagnose system/component failures.This capability can also be used to conduct planning and analysis of cryogenics and other fluidsystems designs. This capability will be interfaced with the ground operations command andcontrol system as a part of the Advanced Ground Systems Maintenance (AGSM) project to helpassure system availability and mission success. The initial capability will be developed for theLiquid Oxygen (LO2) ground loading systems.

[Analysis of telemetry, on-line and non-telemetry data for characterization of the physical activity of patients with heart failure].

PubMed

Melczer, Csaba; Melczer, László; Goják, Ilona; Kónyi, Attila; Szabados, Sándor; Raposa, László Bence; Oláh, András; Ács, Pongrác

2017-09-01

Several studies have demonstrated that the prevalence of heart disease can be accounted for between 0.4 and 2% in developed countries. The present study aimed to use the PA% of the telemetry data to estimate the 6-minute walk test result. A total of seventeen patients with heart disease; 3 females and 14 males; age: 57.35 yrs ± 9.54; body mass 98.71 ± 9.89 kg; average BMI 36.69 ± 3.67 were recruited into the study. Using the two sets of values describing physical performance, linear regression was calculated providing a mathematical equation, thus, the Physical Activity % value is used to estimate the distance traveled over a 6-minute walk test. On further data analysis, we have come to the conclusion that the distance walked during the six-minute-long test may be measured by PA% from the data of CRT device. With our method, based on the values received from the physical activity sensor implanted into the resynchronisation devices, changes in patients' health status could be monitored telemetrically with the assistance from the implanted electronic device. Orv Hetil. 2017; 158(35): 1390-1395.

A situated reasoning architecture for space-based repair and replace tasks

NASA Technical Reports Server (NTRS)

Bloom, Ben; Mcgrath, Debra; Sanborn, Jim

1989-01-01

Space-based robots need low level control for collision detection and avoidance, short-term load management, fine-grained motion, and other physical tasks. In addition, higher level control is required to focus strategic decision making as missions are assigned and carried out. Reasoning and control must be responsive to ongoing changes in the environment. Research aimed at bridging the gap between high level artificial intelligence (AI) planning techniques and task-level robot programming for telerobotic systems is described. Situated reasoning is incorporated into AI and Robotics systems in order to coordinate a robot's activity within its environment. An integrated system under development in a component maintenance domain is described. It is geared towards replacing worn and/or failed Orbital Replacement Units (ORUs) designed for use aboard NASA's Space Station Freedom based on the collection of components available at a given time. High level control reasons in component space in order to maximize the number operational component-cells over time, while the task-level controls sensors and effectors, detects collisions, and carries out pick and place tasks in physical space. Situated reasoning is used throughout the system to cope with component failures, imperfect information, and unexpected events.

Using 3d Bim Model for the Value-Based Land Share Calculations

NASA Astrophysics Data System (ADS)

Çelik Şimşek, N.; Uzun, B.

2017-11-01

According to the Turkish condominium ownership system, 3D physical buildings and its condominium units are registered to the condominium ownership books via 2D survey plans. Currently, 2D representations of the 3D physical objects, causes inaccurate and deficient implementations for the determination of the land shares. Condominium ownership and easement right are established with a clear indication of land shares (condominium ownership law, article no. 3). So, the land share of each condominium unit have to be determined including the value differences among the condominium units. However the main problem is that, land share has often been determined with area based over the project before construction of the building. The objective of this study is proposing a new approach in terms of value-based land share calculations of the condominium units that subject to condominium ownership. So, the current approaches and its failure that have taken into account in determining the land shares are examined. And factors that affect the values of the condominium units are determined according to the legal decisions. This study shows that 3D BIM models can provide important approaches for the valuation problems in the determination of the land shares.

Identifying bio-physical, social and political challenges to catchment governance for sustainable freshwater fisheries in West Africa: Systems overview through scenario development in the SUSFISH project.

NASA Astrophysics Data System (ADS)

Sendzimir, Jan; Slezak, Gabriele; Melcher, Andreas

2015-04-01

Chronic and episodic water scarcity prompted construction of 1400 reservoirs in Burkina Faso since 1950, greatly expanding fisheries production. These fisheries provided an increasingly important protein source for a population that has risen 600% since 1920, but production has plateaued, and dramatic declines in adult fish size suggest these fisheries are not sustainable. The SUSFISH project joined Austrian and Burkinabe scientists to increase local capacities to manage fisheries sustainably. SUSFISH has successfully increased capacity to monitor fish populations, identify endangered species, and use specific fish and macroinvertebrate species as bio-indicators of water and habitat quality as well as anthropogenic pressures. But projects to support sustainable development in Africa have a long history of failure if only based on transfer of technology and theory based on bio-physical sciences. This paper describes the processes and products of knowledge elicitation, scenario development and systems analysis to identify barriers and bridges to long-term sustainable fisheries development that arise from bio-physical, social, political and cultural causes, and, especially, interactions between them. Lessons learned and important on-going research questions are identified for both the natural and social sciences as they apply to managing catchments at multiple scales of governance, from local to national.

Generalized Finsler geometric continuum physics with applications in fracture and phase transformations

NASA Astrophysics Data System (ADS)

Clayton, J. D.

2017-02-01

A theory of deformation of continuous media based on concepts from Finsler differential geometry is presented. The general theory accounts for finite deformations, nonlinear elasticity, and changes in internal state of the material, the latter represented by elements of a state vector of generalized Finsler space whose entries consist of one or more order parameter(s). Two descriptive representations of the deformation gradient are considered. The first invokes an additive decomposition and is applied to problems involving localized inelastic deformation mechanisms such as fracture. The second invokes a multiplicative decomposition and is applied to problems involving distributed deformation mechanisms such as phase transformations or twinning. Appropriate free energy functions are posited for each case, and Euler-Lagrange equations of equilibrium are derived. Solutions are obtained for specific problems of tensile fracture of an elastic cylinder and for amorphization of a crystal under spherical and uniaxial compression. The Finsler-based approach is demonstrated to be more general and potentially more physically descriptive than existing hyperelasticity models couched in Riemannian geometry or Euclidean space, without incorporation of supplementary ad hoc equations or spurious fitting parameters. Predictions for single crystals of boron carbide ceramic agree qualitatively, and in many instances quantitatively, with results from physical experiments and atomic simulations involving structural collapse and failure of the crystal along its c-axis.

Increasing exercise capacity and quality of life of patients with heart failure through Wii gaming: the rationale, design and methodology of the HF-Wii study; a multicentre randomized controlled trial.

PubMed

Jaarsma, Tiny; Klompstra, Leonie; Ben Gal, Tuvia; Boyne, Josiane; Vellone, Ercole; Bäck, Maria; Dickstein, Kenneth; Fridlund, Bengt; Hoes, Arno; Piepoli, Massimo F; Chialà, Oronzo; Mårtensson, Jan; Strömberg, Anna

2015-07-01

Exercise is known to be beneficial for patients with heart failure (HF), and these patients should therefore be routinely advised to exercise and to be or to become physically active. Despite the beneficial effects of exercise such as improved functional capacity and favourable clinical outcomes, the level of daily physical activity in most patients with HF is low. Exergaming may be a promising new approach to increase the physical activity of patients with HF at home. The aim of this study is to determine the effectiveness of the structured introduction and access to a Wii game computer in patients with HF to improve exercise capacity and level of daily physical activity, to decrease healthcare resource use, and to improve self-care and health-related quality of life. A multicentre randomized controlled study with two treatment groups will include 600 patients with HF. In each centre, patients will be randomized to either motivational support only (control) or structured access to a Wii game computer (Wii). Patients in the control group will receive advice on physical activity and will be contacted by four telephone calls. Patients in the Wii group also will receive advice on physical activity along with a Wii game computer, with instructions and training. The primary endpoint will be exercise capacity at 3 months as measured by the 6 min walk test. Secondary endpoints include exercise capacity at 6 and 12 months, level of daily physical activity, muscle function, health-related quality of life, and hospitalization or death during the 12 months follow-up. The HF-Wii study is a randomized study that will evaluate the effect of exergaming in patients with HF. The findings can be useful to healthcare professionals and improve our understanding of the potential role of exergaming in the treatment and management of patients with HF. NCT01785121. © 2015 The Authors. European Journal of Heart Failure © 2015 European Society of Cardiology.

Solving Tomorrow's Problems Today? Daily Anticipatory Coping and Reactivity to Daily Stressors.

PubMed

Neupert, Shevaun D; Ennis, Gilda E; Ramsey, Jennifer L; Gall, Agnes A

2016-07-01

The present study examined the day-to-day fluctuation of state-like anticipatory coping (coping employed prior to stressors) and how these coping processes relate to important outcomes for older adults (i.e., physical health, affect, memory failures). Forty-three older adults aged 60-96 (M = 74.65, SD = 8.19) participated in an 8-day daily diary study of anticipatory coping, stressors, health, affect, and memory failures. Participants reported anticipatory coping behaviors on one day with respect to 6 distinct stressor domains that could occur the following day. Multilevel models indicated that anticipatory coping changes from day to day and within stressor domains. Lagged associations suggested that yesterday's anticipatory coping for potential upcoming arguments is related to today's physical health and affect. Increased stagnant deliberation is associated with reduced cognitive reactivity (i.e., fewer memory failures) to arguments the next day. Taken together, these findings suggest that anticipatory coping is dynamic and associated with important daily outcomes. © The Author 2015. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Academic Failure in Secondary School: The Inter-Related Role of Health Problems and Educational Context.

PubMed

Needham, Belinda L; Crosnoe, Robert; Muller, Chandra

2004-01-01

This study explores whether the interplay of health problems and school environment predicts academic failure, an individual event with consequences for the life course, as well as for society at large. This exploration proceeds in three steps: 1) we examine whether physical and mental health problems are an academic risk factor during secondary school; 2) we investigate the academic mechanisms underlying this risk status; and 3) we explore whether this risk status varies by school context. A series of logistic regressions reveals that self-rated health and emotional distress are both associated with greater likelihood of failing one or more classes in the next year and that absenteeism, trouble with homework, and student-teacher bonding account for much of these associations. Associations of physical and mental health problems with academic failure vary only slightly across schools, however. We discuss the implications of these findings for both research and policy and argue that the examination of overlap among different domains of adolescent functioning can advance the sociological understanding of health, education, and social problems in general.

A critique of the molecular target-based drug discovery paradigm based on principles of metabolic control: advantages of pathway-based discovery.

PubMed

Hellerstein, Marc K

2008-01-01

Contemporary drug discovery and development (DDD) is dominated by a molecular target-based paradigm. Molecular targets that are potentially important in disease are physically characterized; chemical entities that interact with these targets are identified by ex vivo high-throughput screening assays, and optimized lead compounds enter testing as drugs. Contrary to highly publicized claims, the ascendance of this approach has in fact resulted in the lowest rate of new drug approvals in a generation. The primary explanation for low rates of new drugs is attrition, or the failure of candidates identified by molecular target-based methods to advance successfully through the DDD process. In this essay, I advance the thesis that this failure was predictable, based on modern principles of metabolic control that have emerged and been applied most forcefully in the field of metabolic engineering. These principles, such as the robustness of flux distributions, address connectivity relationships in complex metabolic networks and make it unlikely a priori that modulating most molecular targets will have predictable, beneficial functional outcomes. These same principles also suggest, however, that unexpected therapeutic actions will be common for agents that have any effect (i.e., that complexity can be exploited therapeutically). A potential operational solution (pathway-based DDD), based on observability rather than predictability, is described, focusing on emergent properties of key metabolic pathways in vivo. Recent examples of pathway-based DDD are described. In summary, the molecular target-based DDD paradigm is built on a naïve and misleading model of biologic control and is not heuristically adequate for advancing the mission of modern therapeutics. New approaches that take account of and are built on principles described by metabolic engineers are needed for the next generation of DDD.

A Framework for Creating a Function-based Design Tool for Failure Mode Identification

NASA Technical Reports Server (NTRS)

Arunajadai, Srikesh G.; Stone, Robert B.; Tumer, Irem Y.; Clancy, Daniel (Technical Monitor)

2002-01-01

Knowledge of potential failure modes during design is critical for prevention of failures. Currently industries use procedures such as Failure Modes and Effects Analysis (FMEA), Fault Tree analysis, or Failure Modes, Effects and Criticality analysis (FMECA), as well as knowledge and experience, to determine potential failure modes. When new products are being developed there is often a lack of sufficient knowledge of potential failure mode and/or a lack of sufficient experience to identify all failure modes. This gives rise to a situation in which engineers are unable to extract maximum benefits from the above procedures. This work describes a function-based failure identification methodology, which would act as a storehouse of information and experience, providing useful information about the potential failure modes for the design under consideration, as well as enhancing the usefulness of procedures like FMEA. As an example, the method is applied to fifteen products and the benefits are illustrated.

High-throughput sequencing: a failure mode analysis.

PubMed

Yang, George S; Stott, Jeffery M; Smailus, Duane; Barber, Sarah A; Balasundaram, Miruna; Marra, Marco A; Holt, Robert A

2005-01-04

Basic manufacturing principles are becoming increasingly important in high-throughput sequencing facilities where there is a constant drive to increase quality, increase efficiency, and decrease operating costs. While high-throughput centres report failure rates typically on the order of 10%, the causes of sporadic sequencing failures are seldom analyzed in detail and have not, in the past, been formally reported. Here we report the results of a failure mode analysis of our production sequencing facility based on detailed evaluation of 9,216 ESTs generated from two cDNA libraries. Two categories of failures are described; process-related failures (failures due to equipment or sample handling) and template-related failures (failures that are revealed by close inspection of electropherograms and are likely due to properties of the template DNA sequence itself). Preventative action based on a detailed understanding of failure modes is likely to improve the performance of other production sequencing pipelines.

Rethinking Mathematics.

ERIC Educational Resources Information Center

Abad, Ernesto A.

1994-01-01

Poses solutions for our failure to show students how well mathematics interlocks with the physical structures of the Universe. Some examples are provided to illustrate the natural integration of mathematics and science. (ZWH)

Gender differences in and factors related to self-care behaviors: a cross-sectional, correlational study of patients with heart failure.

PubMed

Heo, Seongkum; Moser, Debra K; Lennie, Terry A; Riegel, Barbara; Chung, Misook L

2008-12-01

Although self-care may reduce exacerbations of heart failure, reported rates of effective self-care in patients with heart failure are low. Modifiable factors, including psychosocial status, knowledge, and physical factors, are thought to influence heart failure self-care, but little is known about their combined impact on self-care. The objective of this study was to identify factors related to self-care behaviors in patients with heart failure. A cross-sectional, correlational study design was used. One hundred twenty-two patients (77 men and 45 women, mean age 60+/-12 years old, 66% New York Heart Association functional class III/IV) were recruited from the outpatient clinics of an academic medical center and two community hospitals. Data on self-care behaviors (Self-Care of Heart Failure Index), depressive symptoms, perceived control, self-care confidence, knowledge, functional status, and social support were collected. Factors related to self-care were examined using hierarchical multiple regression. Mean self-care behavior scores were less than 70 indicating the majority of men and women with HF did not consistently engage in self-care behaviors. Higher self-care confidence and perceived control and better heart failure management knowledge were associated with better self-care (r2=.25, p<.001). Higher perceived control and better knowledge were related to better self-care behaviors in men (r2=.18, p=.001), while higher self-care confidence and poorer functional status were related to better self-care behaviors in women (r2=.35, p<.001). This study demonstrates the substantial impact of modifiable factors such as confidence in one's self-care abilities, perceived control, and knowledge on self-care behaviors. This study demonstrates that there are gender differences in factors affecting self-care, even though at baseline men and women have similar knowledge levels, physical, psychological, and behavioral status. Effective interventions focusing on modifiable factors and the unique characteristics of men and women should be provided to improve self-care behaviors in patients with heart failure.

Small prey species' behaviour and welfare: implications for veterinary professionals.

PubMed

McBride, E Anne

2017-08-01

People have obligations to ensure the welfare of animals under their care. Offences under the UK Animal Welfare Act are acts, or failures of action, causing unnecessary suffering. Veterinary professionals need to be able to provide current, scientifically based prophylactic advice, and respect the limits of their expertise. The ethical concept of a life worth living and the Five Freedoms are core to welfare. Behaviour is a central component, both influencing and influenced by physical health. Owners frequently misunderstand the behaviour of small prey mammals and how to meet their needs. This review provides insight into the physical-social (external) and the cognitive-emotional (internal) environments of small prey mammals, contextualised within an evolutionary perspective. This is extrapolated to captivity and practical suggestions given for meeting behavioural freedoms and enhancing client understanding and enjoyment of their animals, thereby improving welfare. © 2017 British Small Animal Veterinary Association.

DRS: Derivational Reasoning System

NASA Technical Reports Server (NTRS)

Bose, Bhaskar

1995-01-01

The high reliability requirements for airborne systems requires fault-tolerant architectures to address failures in the presence of physical faults, and the elimination of design flaws during the specification and validation phase of the design cycle. Although much progress has been made in developing methods to address physical faults, design flaws remain a serious problem. Formal methods provides a mathematical basis for removing design flaws from digital systems. DRS (Derivational Reasoning System) is a formal design tool based on advanced research in mathematical modeling and formal synthesis. The system implements a basic design algebra for synthesizing digital circuit descriptions from high level functional specifications. DRS incorporates an executable specification language, a set of correctness preserving transformations, verification interface, and a logic synthesis interface, making it a powerful tool for realizing hardware from abstract specifications. DRS integrates recent advances in transformational reasoning, automated theorem proving and high-level CAD synthesis systems in order to provide enhanced reliability in designs with reduced time and cost.

Comprehension and retrieval of failure cases in airborne observatories

NASA Technical Reports Server (NTRS)

Alvarado, Sergio J.; Mock, Kenrick J.

1995-01-01

This paper describes research dealing with the computational problem of analyzing and repairing failures of electronic and mechanical systems of telescopes in NASA's airborne observatories, such as KAO (Kuiper Airborne Observatory) and SOFIA (Stratospheric Observatory for Infrared Astronomy). The research has resulted in the development of an experimental system that acquires knowledge of failure analysis from input text, and answers questions regarding failure detection and correction. The system's design builds upon previous work on text comprehension and question answering, including: knowledge representation for conceptual analysis of failure descriptions, strategies for mapping natural language into conceptual representations, case-based reasoning strategies for memory organization and indexing, and strategies for memory search and retrieval. These techniques have been combined into a model that accounts for: (a) how to build a knowledge base of system failures and repair procedures from descriptions that appear in telescope-operators' logbooks and FMEA (failure modes and effects analysis) manuals; and (b) how to use that knowledge base to search and retrieve answers to questions about causes and effects of failures, as well as diagnosis and repair procedures. This model has been implemented in FANSYS (Failure ANalysis SYStem), a prototype text comprehension and question answering program for failure analysis.

Reliability Evaluation of Machine Center Components Based on Cascading Failure Analysis

NASA Astrophysics Data System (ADS)

Zhang, Ying-Zhi; Liu, Jin-Tong; Shen, Gui-Xiang; Long, Zhe; Sun, Shu-Guang

2017-07-01

In order to rectify the problems that the component reliability model exhibits deviation, and the evaluation result is low due to the overlook of failure propagation in traditional reliability evaluation of machine center components, a new reliability evaluation method based on cascading failure analysis and the failure influenced degree assessment is proposed. A direct graph model of cascading failure among components is established according to cascading failure mechanism analysis and graph theory. The failure influenced degrees of the system components are assessed by the adjacency matrix and its transposition, combined with the Pagerank algorithm. Based on the comprehensive failure probability function and total probability formula, the inherent failure probability function is determined to realize the reliability evaluation of the system components. Finally, the method is applied to a machine center, it shows the following: 1) The reliability evaluation values of the proposed method are at least 2.5% higher than those of the traditional method; 2) The difference between the comprehensive and inherent reliability of the system component presents a positive correlation with the failure influenced degree of the system component, which provides a theoretical basis for reliability allocation of machine center system.

Comprehension and retrieval of failure cases in airborne observatories

NASA Astrophysics Data System (ADS)

Alvarado, Sergio J.; Mock, Kenrick J.

1995-05-01

This paper describes research dealing with the computational problem of analyzing and repairing failures of electronic and mechanical systems of telescopes in NASA's airborne observatories, such as KAO (Kuiper Airborne Observatory) and SOFIA (Stratospheric Observatory for Infrared Astronomy). The research has resulted in the development of an experimental system that acquires knowledge of failure analysis from input text, and answers questions regarding failure detection and correction. The system's design builds upon previous work on text comprehension and question answering, including: knowledge representation for conceptual analysis of failure descriptions, strategies for mapping natural language into conceptual representations, case-based reasoning strategies for memory organization and indexing, and strategies for memory search and retrieval. These techniques have been combined into a model that accounts for: (a) how to build a knowledge base of system failures and repair procedures from descriptions that appear in telescope-operators' logbooks and FMEA (failure modes and effects analysis) manuals; and (b) how to use that knowledge base to search and retrieve answers to questions about causes and effects of failures, as well as diagnosis and repair procedures. This model has been implemented in FANSYS (Failure ANalysis SYStem), a prototype text comprehension and question answering program for failure analysis.

Therapeutic considerations of sarcopenia in heart failure patients.

PubMed

Saitoh, Masakazu; Ebner, Nicole; von Haehling, Stephan; Anker, Stefan D; Springer, Jochen

2018-02-01

Sarcopenia is a common feature, and affects 20-47% of patients with heart failure (HF). Sarcopenia is also an independent predictor of impaired functional capacity, even after adjusting for clinical relevant variables, which is associated with adverse outcome in patients with HF. Areas covered: Several different pathophysiological pathways are involved in sarcopenic processes including altered nutrient intake and absorption, hormonal factor, inflammatory processes, oxidative stress, cellular proteolysis, and unhealthy lifestyle. Nutritional therapy, physical activity and/or exercise training have been associated with improved muscle mass or physical performance in HF. Few studies reported beneficial effects for muscle mass and physical performance, in those who received angiotensin-converting enzyme (ACE) inhibitors, or/and beta-blocker. In addition, testosterone, selective androgen receptor modulators, ghrelin agonist and myostatin inhibitors are currently under study as possible future therapeutic options. Expert commentary: Regular and adequate level of physical activity and/or exercise training, and sufficient nutritional intake or special nutritional supplementation may represent the best strategy for prevention or delay of sarcopenia and worsening physical performance in patients with HF. Maximal tolerated dosages of standard therapies for HF such as ACE-inhibitors or beta-blockers are first-line strategy, however it is difficult to recommend other pharmacological agents as part of routine treatment of sarcopenia.

Real-time failure control (SAFD)

NASA Technical Reports Server (NTRS)

Panossian, Hagop V.; Kemp, Victoria R.; Eckerling, Sherry J.

1990-01-01

The Real Time Failure Control program involves development of a failure detection algorithm, referred as System for Failure and Anomaly Detection (SAFD), for the Space Shuttle Main Engine (SSME). This failure detection approach is signal-based and it entails monitoring SSME measurement signals based on predetermined and computed mean values and standard deviations. Twenty four engine measurements are included in the algorithm and provisions are made to add more parameters if needed. Six major sections of research are presented: (1) SAFD algorithm development; (2) SAFD simulations; (3) Digital Transient Model failure simulation; (4) closed-loop simulation; (5) SAFD current limitations; and (6) enhancements planned for.

Mechanics-Based Definition of Safety Factors Against Flow Failure in Unsaturated Shallow Slopes

NASA Astrophysics Data System (ADS)

Buscarnera, G.; Lizarraga-Barrera, J.

2014-12-01

Physical models for landslide forecasting rely on the combination of hydrologic models for water infiltration and stability criteria based on infinite slope mechanics. Such concepts can be used to derive safety factors for shallow landsliding, in which the mobilization of the soil cover is associated with the attainment of critical values of pore water pressures expressed as a function of the frictional strength. While such models capture the role of important geomorphic features and geotechnical properties, their performance depends on the validity of the postulate of frictional failure. As a result, the safety factors do not to consider a broader range of solid-fluid interactions promoting different slope failure mechanisms, such as flow slides. This work combines principles of soil stability, unsaturated soil mechanics and plasticity theory to derive an alternative set of safety factors. While frictional slips are included in the study as a particular case, the proposed analytical methodology can also be applied to cases in which an increase in degree of saturation promotes liquefaction instabilities, i.e. possible transitions from solid- to fluid-like response. The study shows that the incorporation of principles of unsaturated soil mechanics into slope stability analyses generates suction-dependent coefficients that alter the value of the safety factors. As a result, while the proposed approach can still be combined with standard hydrologic models simulating the evolution of pore pressures in the near-surface, it can also provide a spatially distributed assessment of evolving safety conditions in landscapes susceptible to landslides of the flow type.

Failure detection system risk reduction assessment

NASA Technical Reports Server (NTRS)

Aguilar, Robert B. (Inventor); Huang, Zhaofeng (Inventor)

2012-01-01

A process includes determining a probability of a failure mode of a system being analyzed reaching a failure limit as a function of time to failure limit, determining a probability of a mitigation of the failure mode as a function of a time to failure limit, and quantifying a risk reduction based on the probability of the failure mode reaching the failure limit and the probability of the mitigation.

An efficient scan diagnosis methodology according to scan failure mode for yield enhancement

NASA Astrophysics Data System (ADS)

Kim, Jung-Tae; Seo, Nam-Sik; Oh, Ghil-Geun; Kim, Dae-Gue; Lee, Kyu-Taek; Choi, Chi-Young; Kim, InSoo; Min, Hyoung Bok

2008-12-01

Yield has always been a driving consideration during fabrication of modern semiconductor industry. Statistically, the largest portion of wafer yield loss is defective scan failure. This paper presents efficient failure analysis methods for initial yield ramp up and ongoing product with scan diagnosis. Result of our analysis shows that more than 60% of the scan failure dies fall into the category of shift mode in the very deep submicron (VDSM) devices. However, localization of scan shift mode failure is very difficult in comparison to capture mode failure because it is caused by the malfunction of scan chain. Addressing the biggest challenge, we propose the most suitable analysis method according to scan failure mode (capture / shift) for yield enhancement. In the event of capture failure mode, this paper describes the method that integrates scan diagnosis flow and backside probing technology to obtain more accurate candidates. We also describe several unique techniques, such as bulk back-grinding solution, efficient backside probing and signal analysis method. Lastly, we introduce blocked chain analysis algorithm for efficient analysis of shift failure mode. In this paper, we contribute to enhancement of the yield as a result of the combination of two methods. We confirm the failure candidates with physical failure analysis (PFA) method. The direct feedback of the defective visualization is useful to mass-produce devices in a shorter time. The experimental data on mass products show that our method produces average reduction by 13.7% in defective SCAN & SRAM-BIST failure rates and by 18.2% in wafer yield rates.

Field Programmable Gate Array Failure Rate Estimation Guidelines for Launch Vehicle Fault Tree Models

NASA Technical Reports Server (NTRS)

Al Hassan, Mohammad; Novack, Steven D.; Hatfield, Glen S.; Britton, Paul

2017-01-01

Today's launch vehicles complex electronic and avionic systems heavily utilize the Field Programmable Gate Array (FPGA) integrated circuit (IC). FPGAs are prevalent ICs in communication protocols such as MIL-STD-1553B, and in control signal commands such as in solenoid/servo valves actuations. This paper will demonstrate guidelines to estimate FPGA failure rates for a launch vehicle, the guidelines will account for hardware, firmware, and radiation induced failures. The hardware contribution of the approach accounts for physical failures of the IC, FPGA memory and clock. The firmware portion will provide guidelines on the high level FPGA programming language and ways to account for software/code reliability growth. The radiation portion will provide guidelines on environment susceptibility as well as guidelines on tailoring other launch vehicle programs historical data to a specific launch vehicle.

Experimental Longitudinal Test of the Influence of Autonomy-Supportive Teaching on Motivation for Participation in Elementary School Physical Education

ERIC Educational Resources Information Center

Leptokaridou, Elisavet T.; Vlachopoulos, Symeon P.; Papaioannou, Athanasios G.

2016-01-01

The present study examined the efficacy of autonomy-supportive teaching during elementary school physical education (PE) in influencing pupils' enjoyment, fear of failure, boredom and effort. A sample of 54 pupils attending fifth and sixth grades comprised the control group (typical instruction; n = 27) and the experimental group…

Capacitor Technologies, Applications and Reliability

NASA Technical Reports Server (NTRS)

1981-01-01

Various aspects of capacitor technologies and applications are discussed. Major emphasis is placed on: the causes of failures; accelerated testing; screening tests; destructive physical analysis; applications techniques; and improvements in capacitor capabilities.

Investigation of abrupt degradation of drain current caused by under-gate crack in AlGaN/GaN high electron mobility transistors during high temperature operation stress

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeng, Chang; Liao, XueYang; Li, RuGuan

2015-09-28

In this paper, we investigate the degradation mode and mechanism of AlGaN/GaN based high electron mobility transistors (HEMTs) during high temperature operation (HTO) stress. It demonstrates that there was abrupt degradation mode of drain current during HTO stress. The abrupt degradation is ascribed to the formation of crack under the gate which was the result of the brittle fracture of epilayer based on failure analysis. The origin of the mechanical damage under the gate is further investigated and discussed based on top-down scanning electron microscope, cross section transmission electron microscope and energy dispersive x-ray spectroscopy analysis, and stress simulation. Basedmore » on the coupled analysis of the failure physical feature and stress simulation considering the coefficient of thermal expansion (CTE) mismatch in different materials in gate metals/semiconductor system, the mechanical damage under the gate is related to mechanical stress induced by CTE mismatch in Au/Ti/Mo/GaN system and stress concentration caused by the localized structural damage at the drain side of the gate edge. These results indicate that mechanical stress induced by CTE mismatch of materials inside the device plays great important role on the reliability of AlGaN/GaN HEMTs during HTO stress.« less

A Diagnostic Post-Occupancy Evaluation of the Nacadia® Therapy Garden.

PubMed

Sidenius, Ulrik; Karlsson Nyed, Patrik; Linn Lygum, Victoria; K Stigsdotter, Ulrika

2017-08-05

The design of the Nacadia® therapy garden is based on a model for evidence-based health design in landscape architecture (EBHDL). One element of the model is a diagnostic post-occupancy evaluation (DPOE), which has not previously been fully developed. The present study develops a generic DPOE for therapy gardens, with a focus on studying the effects of the design on patients' health outcomes. This is done in order to identify successes and failures in the design. By means of a triangulation approach, the DPOE employs a mixture of methods, and data is interpreted corroborating. The aim of the present study is to apply the DPOE to the Nacadia® therapy garden. The results of the DPOE suggest that the design of the Nacadia® therapy garden fulfills its stated aims and objectives. The overall environment of the Nacadia ® therapy garden was experienced as protective and safe, and successfully incorporated the various elements of the nature-based therapy programme. The participants encountered meaningful spaces and activities which suited their current physical and mental capabilities, and the health outcome measured by EQ-VAS (self-estimated general health) indicated a significant increase. Some design failures were identified, of which visual exposure was the most noteworthy. The DPOE model presented appears to be efficient but would nonetheless profit from being validated by other cases.

A Diagnostic Post-Occupancy Evaluation of the Nacadia® Therapy Garden

PubMed Central

Sidenius, Ulrik; Karlsson Nyed, Patrik; Linn Lygum, Victoria; K. Stigsdotter, Ulrika

2017-01-01

The design of the Nacadia® therapy garden is based on a model for evidence-based health design in landscape architecture (EBHDL). One element of the model is a diagnostic post-occupancy evaluation (DPOE), which has not previously been fully developed. The present study develops a generic DPOE for therapy gardens, with a focus on studying the effects of the design on patients’ health outcomes. This is done in order to identify successes and failures in the design. By means of a triangulation approach, the DPOE employs a mixture of methods, and data is interpreted corroborating. The aim of the present study is to apply the DPOE to the Nacadia® therapy garden. The results of the DPOE suggest that the design of the Nacadia® therapy garden fulfills its stated aims and objectives. The overall environment of the Nacadia ® therapy garden was experienced as protective and safe, and successfully incorporated the various elements of the nature-based therapy programme. The participants encountered meaningful spaces and activities which suited their current physical and mental capabilities, and the health outcome measured by EQ-VAS (self-estimated general health) indicated a significant increase. Some design failures were identified, of which visual exposure was the most noteworthy. The DPOE model presented appears to be efficient but would nonetheless profit from being validated by other cases. PMID:28783060

Reliability of objects in aerospace technologies and beyond: Holistic risk management approach

NASA Astrophysics Data System (ADS)

Shai, Yair; Ingman, D.; Suhir, E.

A “ high level” , deductive-reasoning-based (“ holistic” ), approach is aimed at the direct analysis of the behavior of a system as a whole, rather than with an attempt to understand the system's behavior by conducting first a “ low level” , inductive-reasoning-based, analysis of the behavior and the contributions of the system's elements. The holistic view on treatment is widely accepted in medical practice, and “ holistic health” concept upholds that all the aspects of people's needs (psychological, physical or social), should be seen as a whole, and that a disease is caused by the combined effect of physical, emotional, spiritual, social and environmental imbalances. Holistic reasoning is applied in our analysis to model the behavior of engineering products (“ species” ) subjected to various economic, marketing, and reliability “ health” factors. Vehicular products (cars, aircraft, boats, etc.), e.g., might be still robust enough, but could be out-of-date, or functionally obsolete, or their further use might be viewed as unjustifiably expensive. High-level-performance functions (HLPF) are the essential feature of the approach. HLPFs are, in effect, “ signatures” of the “ species” of interest. The HLPFs describe, in a “ holistic” , and certainly in a probabilistic, way, numerous complex multi-dependable relations among the representatives of the “ species” under consideration. ; umerous inter-related “ stresses” , both actual (“ physical” ) and nonphysical, which affect the probabilistic predictions are inherently being taken into account by the HLPFs. There is no need, and might even be counter-productive, to conduct tedious, time- and labor-consuming experimentations and to invest significant amount of time and resources to accumulate “ representative statistics” to predict - he governing probabilistic characteristics of the system behavior, such as, e.g., life expectancy of a particular type of products. “ Species” of military aircraft, commercial aircraft and private cars have been chosen in our analysis as illustrations of the fruitfulness of the “ holistic” approach. The obtained data show that both commercial “ species” exhibit similar “ survival dynamics” in compare with those of the military species of aircraft: lifetime distributions were found to be Weibull distributions for all “ species” however for commercial vehicles, the shape parameters were a little higher than 2, and scale parameters were 19.8 years (aircraft) and 21.7 (cars) whereas for military aircraft, the shape parameters were much higher and the mean time to failure much longer. The difference between the lifetime characteristics of the “ species” can be attributed to the differences in the social, operational, economic and safety-and-reliability requirements and constraints. The obtained information can be used to make tentative predictions for the most likely trends in the given field of vehicular technology. The following major conclusions can be drawn from our analysis: 1) The suggested concept based on the use of HLPFs reflects the current state and the general perceptions in the given field of engineering, including aerospace technologies, and allows for all the inherent and induced factors to be taken into account: any type of failures, usage profiles, economic factors, environmental conditions, etc. The concept requires only very general input data for the entire population. There is no need for the less available information about individual articles. 2) Failure modes are not restricted to the physical type of failures and include economic, cultural or social effects. All possible causes, which might lead to making a decision to terminate the use of a particular type

Determining bruise etiology in muscle tissue using finite element analysis.

PubMed

Tang, Kevin; Sharpe, Wyatt; Schulz, Alexandra; Tam, Edric; Grosse, Ian; Tis, John; Cullinane, Dennis

2014-03-01

Bruising, the result of capillary failure, is a common physical exam finding due to blunt trauma and, depending on location and severity, a potential indicator of abuse. Despite its clinical relevance, few studies have investigated the etiology of capillary failure. The goal of this study was to determine whether capillaries primarily fail under shear stress or hydraulic-induced tensile stress. An arteriole bifurcating into four capillaries was modeled using ANSYS 14.0 (®) . The capillaries were embedded in muscle tissue and a pressure of 20.4 kPa was applied. Any tensile stress exceeding 8.4 × 10(4)  Pa was considered failure. Results showed that failure occurred directly under the impact zone and where capillaries bifurcated, rather than along the line of greatest shear stress, indicating that internal tensile stress is likely the primary mode of capillary failure in bruising. These results are supported by the concept that bruising can occur via blunt trauma in which no shearing lacerations occur. © 2013 American Academy of Forensic Sciences.

Ductile failure initiation and evolution in porous polycrystalline aggregates due to interfacial effects

NASA Astrophysics Data System (ADS)

Ashmawi, Waeil Muhammad Al-Anwar

New analytical and computational formulations have been developed for the investigation of micro structurally induced ductile failure mechanisms in porous polycrystalline aggregates with low and high (CSL) angle grain-boundaries (GBs). A multiple-slip rate-dependent crystalline constitutive formulation that is coupled to the evolution of mobile and immobile dislocation densities, a new internal porosity formulation for void nucleation and growth, and specialized computational schemes have been developed to obtain a detailed understanding of the multi-scale interrelated physical mechanisms that result in ductile failure in polycrystalline materials. Comprehensive transmission and pile-up mechanisms have also been introduced to investigate dislocation-density impedance and slip-rate incompatibility at the GBs. The interrelated effects of GB orientation, mobile and immobile dislocation densities, strain hardening, geometrical softening, localized plastic strains, and dislocation-density transmission and blockage on void growth, interaction, and coalescence have been studied. Criteria have been developed to identify and monitor the initiation and development of potential dislocation-density activity sites adjacent to GB regions. These interactions play an important role in the formation of GB pile-up and transmission regions. The effects of GB structure and orientation on ductile failure have been accounted for by the development of GB interfacial kinematic conditions that account for a multitude of dislocation-density interactions with GBs, such as full and partial transmission, impedance, blockage, and absorption. Pile-ups and transmission regions are identified and monitored as the deformation and failure evolve. These kinematic conditions are linked to the initiation and evolution of failure modes by the development of a new internal porosity evolution formulation that accounts for void nucleation and growth. The internal porosity relation is coupled with the proposed dislocation-density based crystalline constitutive formulation, the interfacial GB dislocation-density interaction models, and the specialized computational schemes to obtain detailed predictions of the behavior of aggregates with explicit voids that have different orientations and combinations of sizes, shapes, and spacings. Results from the present study indicate that material failure is a competition between different interrelated effects, such as stress triaxiality, accumulated plastic shear strain, temperature, dislocation density concentration, and grain and GB crystallographic orientations. For all void arrangements, as the void size is increased, specimen necking is diffuse and failure is concentrated in the ligament regions. Furthermore, there are more dislocation-density activity sites for potential transmission and pile-ups at the GBs. Failure is concentrated along the void peripheries and within intervoid ligaments. It has been shown that the evolution of the mobile dislocation density saturation curves, and their saturation rate are directly related to the aggregate response. Nucleation and growth for all void distributions have occurred in regions of maximum dislocation density and along preferred crystallographic orientations. Spatial distributions of porosity, accumulated plastic strains, and pressure have been obtained to further elucidate how these parameters evolve and affect void to void interaction in critical ligament and localized regions as a function of intervoid spacing and nominal strains. These failure predictions can be also used to identify intergranular and transgranular failure propagation. The present study underscores the importance of using dislocation-density based multiple-slip crystalline constitutive formulations and GB interfacial mechanisms that are consistent with experimental observations and results to accurately characterize the microstructural evolution of deformation and failure modes on a length scale that is commensurate with the material competition between the inherent strengthening and softening mechanisms of crystalline systems.

A Comparison between Physics-based and Polytropic MHD Models for Stellar Coronae and Stellar Winds of Solar Analogs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cohen, O.

The development of the Zeeman–Doppler Imaging (ZDI) technique has provided synoptic observations of surface magnetic fields of low-mass stars. This led the stellar astrophysics community to adopt modeling techniques that have been used in solar physics using solar magnetograms. However, many of these techniques have been neglected by the solar community due to their failure to reproduce solar observations. Nevertheless, some of these techniques are still used to simulate the coronae and winds of solar analogs. Here we present a comparative study between two MHD models for the solar corona and solar wind. The first type of model is amore » polytropic wind model, and the second is the physics-based AWSOM model. We show that while the AWSOM model consistently reproduces many solar observations, the polytropic model fails to reproduce many of them, and in the cases where it does, its solutions are unphysical. Our recommendation is that polytropic models, which are used to estimate mass-loss rates and other parameters of solar analogs, must first be calibrated with solar observations. Alternatively, these models can be calibrated with models that capture more detailed physics of the solar corona (such as the AWSOM model) and that can reproduce solar observations in a consistent manner. Without such a calibration, the results of the polytropic models cannot be validated, but they can be wrongly used by others.« less

TU-FG-201-12: Designing a Risk-Based Quality Assurance Program for a Newly Implemented Y-90 Microspheres Procedure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vile, D; Zhang, L; Cuttino, L

2016-06-15

Purpose: To create a quality assurance program based upon a risk-based assessment of a newly implemented SirSpheres Y-90 procedure. Methods: A process map was created for a newly implemented SirSpheres procedure at a community hospital. The process map documented each step of this collaborative procedure, as well as the roles and responsibilities of each member. From the process map, different potential failure modes were determined as well as any current controls in place. From this list, a full failure mode and effects analysis (FMEA) was performed by grading each failure mode’s likelihood of occurrence, likelihood of detection, and potential severity.more » These numbers were then multiplied to compute the risk priority number (RPN) for each potential failure mode. Failure modes were then ranked based on their RPN. Additional controls were then added, with failure modes corresponding to the highest RPNs taking priority. Results: A process map was created that succinctly outlined each step in the SirSpheres procedure in its current implementation. From this, 72 potential failure modes were identified and ranked according to their associated RPN. Quality assurance controls and safety barriers were then added for failure modes associated with the highest risk being addressed first. Conclusion: A quality assurance program was created from a risk-based assessment of the SirSpheres process. Process mapping and FMEA were effective in identifying potential high-risk failure modes for this new procedure, which were prioritized for new quality assurance controls. TG 100 recommends the fault tree analysis methodology to design a comprehensive and effective QC/QM program, yet we found that by simply introducing additional safety barriers to address high RPN failure modes makes the whole process simpler and safer.« less

Midlife Physical Activity and Mobility in Older Age

PubMed Central

Patel, Kushang V.; Coppin, Antonia K.; Manini, Todd M.; Lauretani, Fulvio; Bandinelli, Stefania; Ferrucci, Luigi; Guralnik, Jack M.

2009-01-01

Background Among older adults, loss of mobility represents a critical stage in the disablement process, whereby the risk for disability is significantly increased. Physical activity is a modifiable risk factor that is associated with reduced risk of losing mobility in older adulthood; however, few studies have examined physical activity performed earlier in life in relation to mobility later in life. Methods Data from a population-based study of 1155 adults aged 65 years and older living in the Chianti region of Italy in 1998–2000 were analyzed in 2005 and 2006. Participants retrospectively recalled their physical activity levels in midlife and underwent mobility testing and medical examination. Two objective mobility outcomes were examined as a function of past physical activity: the Short Physical Performance Battery (SPPB) and the ability to walk 400 meters. Results Older Italian adults (mean age 74.8, standard deviation 7.3) who engaged in higher levels of physical activity in midlife were significantly more likely to perform better on the SPPB than individuals who were less physically active in midlife. In addition, failure to complete the 400-meter walk test was significantly less likely among physically active men (Level II) (odds ratio [OR]=0.37, 95% confidence interval [CI]=0.15–0.93) and very active men (Level III) (OR=0.23, 95% CI=0.09–0.63) when compared to men who were less active (Level I) in the past (p for trend, 0.008). These associations remained after adjustment for demographic factors, medical conditions, and physiologic impairments. Conclusions Older adults who reported higher levels of physical activity in midlife had better mobility in old age than less physically active ones. PMID:16905032

Primary health care nurses and heart failure education: a survey.

PubMed

Gilmour, Jean; Strong, Alison; Chan, Helen; Hanna, Sue; Huntington, Annette

2014-09-01

Heart failure education contributes to effective self-management. New Zealand primary health care nurses' contributions to heart failure educational activities have not been researched. To identify primary health care nurses' heart failure educational activities in terms of duration and frequency, topics covered, resources used and strategies for Maori and other ethnic groups. A cross-sectional survey of a random sample of 961 primary health care nurses using a postal questionnaire. Of 630 respondents (65.5%), 369 worked with patients with heart failure and 339 provided heart failure education. One-third of respondents providing education (33.3%; n=113) delivered sessions from 16 to 60 minutes. The main educational topics covered were on the physical aspects of heart failure; prognosis, spiritual/existential and psychosocial topics were least often addressed. One-quarter of the group providing education did not use educational resources (n=86). The majority of respondents reported they would find more education about heart failure useful or very useful (80.2%; n=292), along with nurse practitioner support (64.7%; n=229). Maori-centred services and resources and involving whanau/family in education were the most frequently mentioned Maori-specific education strategies. A consistent approach to heart failure education is important to address knowledge gaps in a timely manner. This study affirms the contribution made by primary health care nurses in chronic illness education and highlights the need for further development and investment in ongoing heart failure nursing education and specialist nursing support.

The role of bank collapse on tidal creek ontogeny: A novel process-based model for bank retreat

NASA Astrophysics Data System (ADS)

Gong, Zheng; Zhao, Kun; Zhang, Changkuan; Dai, Weiqi; Coco, Giovanni; Zhou, Zeng

2018-06-01

Bank retreat in coastal tidal flats plays a primary role on the planimetric shape of tidal creeks and is commonly driven by both flow-induced bank erosion and gravity-induced bank collapse. However, existing modelling studies largely focus on bank erosion and overlook bank collapse. We build a bank retreat model coupling hydrodynamics, bank erosion and bank collapse. To simulate the process of bank collapse, a stress-deformation model is utilized to calculate the stress variation of bank soil after bank erosion, and the Mohr-Coulomb failure criterion is then applied to evaluate the stability of the tidal creek bank. Results show that the bank failure process can be categorized into three stages, i.e., shear failure at the bank toe (stage I), tensile failure on the bank top (stage II), and sectional cracking from the bank top to the toe (stage III). With only bank erosion, the planimetric shapes of tidal creeks are funneled due to the gradually seaward increasing discharge. In contrast to bank erosion, bank collapse is discontinuous, and the contribution of bank collapse to bank retreat can reach 85%, highlighting that the expansion of tidal creeks can be dominated by bank collapse process. The planimetric shapes of tidal creeks are funneled with a much faster expansion rate when bank collapse is considered. Overall, this study makes a further step toward more physical and realistic simulation of bank retreat in estuarine and coastal settings and the developed bank collapse module can be readily included in other morphodynamic models.

Reducing Cascading Failure Risk by Increasing Infrastructure Network Interdependence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korkali, Mert; Veneman, Jason G.; Tivnan, Brian F.

Increased coupling between critical infrastructure networks, such as power and communication systems, has important implications for the reliability and security of these systems. To understand the effects of power-communication coupling, several researchers have studied models of interdependent networks and reported that increased coupling can increase vulnerability. However, these conclusions come largely from models that have substantially different mechanisms of cascading failure, relative to those found in actual power and communication networks, and that do not capture the benefits of connecting systems with complementary capabilities. In order to understand the importance of these details, this paper compares network vulnerability in simplemore » topological models and in models that more accurately capture the dynamics of cascading in power systems. First, we compare a simple model of topological contagion to a model of cascading in power systems and find that the power grid model shows a higher level of vulnerability, relative to the contagion model. Second, we compare a percolation model of topological cascading in coupled networks to three different models of power networks coupled to communication systems. Again, the more accurate models suggest very different conclusions than the percolation model. In all but the most extreme case, the physics-based power grid models indicate that increased power-communication coupling decreases vulnerability. This is opposite from what one would conclude from the percolation model, in which zero coupling is optimal. Only in an extreme case, in which communication failures immediately cause grid failures, did we find that increased coupling can be harmful. Together, these results suggest design strategies for reducing the risk of cascades in interdependent infrastructure systems.« less

Reducing Cascading Failure Risk by Increasing Infrastructure Network Interdependence

DOE PAGES

Korkali, Mert; Veneman, Jason G.; Tivnan, Brian F.; ...

2017-03-20

Increased coupling between critical infrastructure networks, such as power and communication systems, has important implications for the reliability and security of these systems. To understand the effects of power-communication coupling, several researchers have studied models of interdependent networks and reported that increased coupling can increase vulnerability. However, these conclusions come largely from models that have substantially different mechanisms of cascading failure, relative to those found in actual power and communication networks, and that do not capture the benefits of connecting systems with complementary capabilities. In order to understand the importance of these details, this paper compares network vulnerability in simplemore » topological models and in models that more accurately capture the dynamics of cascading in power systems. First, we compare a simple model of topological contagion to a model of cascading in power systems and find that the power grid model shows a higher level of vulnerability, relative to the contagion model. Second, we compare a percolation model of topological cascading in coupled networks to three different models of power networks coupled to communication systems. Again, the more accurate models suggest very different conclusions than the percolation model. In all but the most extreme case, the physics-based power grid models indicate that increased power-communication coupling decreases vulnerability. This is opposite from what one would conclude from the percolation model, in which zero coupling is optimal. Only in an extreme case, in which communication failures immediately cause grid failures, did we find that increased coupling can be harmful. Together, these results suggest design strategies for reducing the risk of cascades in interdependent infrastructure systems.« less

Multi-Dimensional Simulation of LWR Fuel Behavior in the BISON Fuel Performance Code

NASA Astrophysics Data System (ADS)

Williamson, R. L.; Capps, N. A.; Liu, W.; Rashid, Y. R.; Wirth, B. D.

2016-11-01

Nuclear fuel operates in an extreme environment that induces complex multiphysics phenomena occurring over distances ranging from inter-atomic spacing to meters, and times scales ranging from microseconds to years. To simulate this behavior requires a wide variety of material models that are often complex and nonlinear. The recently developed BISON code represents a powerful fuel performance simulation tool based on its material and physical behavior capabilities, finite-element versatility of spatial representation, and use of parallel computing. The code can operate in full three dimensional (3D) mode, as well as in reduced two dimensional (2D) modes, e.g., axisymmetric radial-axial ( R- Z) or plane radial-circumferential ( R- θ), to suit the application and to allow treatment of global and local effects. A BISON case study was used to illustrate analysis of Pellet Clad Mechanical Interaction failures from manufacturing defects using combined 2D and 3D analyses. The analysis involved commercial fuel rods and demonstrated successful computation of metrics of interest to fuel failures, including cladding peak hoop stress and strain energy density. In comparison with a failure threshold derived from power ramp tests, results corroborate industry analyses of the root cause of the pellet-clad interaction failures and illustrate the importance of modeling 3D local effects around fuel pellet defects, which can produce complex effects including cold spots in the cladding, stress concentrations, and hot spots in the fuel that can lead to enhanced cladding degradation such as hydriding, oxidation, CRUD formation, and stress corrosion cracking.

Multi-Dimensional Simulation of LWR Fuel Behavior in the BISON Fuel Performance Code

DOE PAGES

Williamson, R. L.; Capps, N. A.; Liu, W.; ...

2016-09-27

Nuclear fuel operates in an extreme environment that induces complex multiphysics phenomena occurring over distances ranging from inter-atomic spacing to meters, and times scales ranging from microseconds to years. To simulate this behavior requires a wide variety of material models that are often complex and nonlinear. The recently developed BISON code represents a powerful fuel performance simulation tool based on its material and physical behavior capabilities, finite-element versatility of spatial representation, and use of parallel computing. The code can operate in full three dimensional (3D) mode, as well as in reduced two dimensional (2D) modes, e.g., axisymmetric radial-axial (R-Z) ormore » plane radial-circumferential (R-θ), to suit the application and to allow treatment of global and local effects. A BISON case study was used in this paper to illustrate analysis of Pellet Clad Mechanical Interaction failures from manufacturing defects using combined 2D and 3D analyses. The analysis involved commercial fuel rods and demonstrated successful computation of metrics of interest to fuel failures, including cladding peak hoop stress and strain energy density. Finally, in comparison with a failure threshold derived from power ramp tests, results corroborate industry analyses of the root cause of the pellet-clad interaction failures and illustrate the importance of modeling 3D local effects around fuel pellet defects, which can produce complex effects including cold spots in the cladding, stress concentrations, and hot spots in the fuel that can lead to enhanced cladding degradation such as hydriding, oxidation, CRUD formation, and stress corrosion cracking.« less

Methods for predicting peak discharge of floods caused by failure of natural and constructed earthen dams

USGS Publications Warehouse

Walder, Joseph S.; O'Connor, Jim E.

1997-01-01

Floods from failures of natural and constructed dams constitute a widespread hazard to people and property. Expeditious means of assessing flood hazards are necessary, particularly in the case of natural dams, which may form suddenly and unexpectedly. We revise statistical relations (derived from data for past constructed and natural dam failures) between peak discharge (Qp) and water volume released (V0) or drop in lake level (d) but assert that such relations, even when cast into a dimensionless form, are of limited utility because they fail to portray the effect of breach-formation rate. We then analyze a simple, physically based model of dam-breach formation to show that the hydrograph at the breach depends primarily on a dimensionless parameter η=kV0/gl/2d7/2, where k is the mean erosion rate of the breach and g is acceleration due to gravity. The functional relationship between Qp and η takes asymptotically distinct forms depending on whether η ≪ 1 (relatively slow breach formation or small lake volume) or η ≫ 1 (relatively fast breach formation or large lake volume). Theoretical predictions agree well with data from dam failures for which k, and thus η, can be estimated. The theory thus provides a rapid means of predicting the plausible range of values of peak discharge at the breach in an earthen dam as long as the impounded water volume and the water depth at the dam face can be estimated.

Association of Physical Activity or Fitness With Incident Heart Failure: A Systematic Review and Meta-Analysis.

PubMed

Echouffo-Tcheugui, Justin B; Butler, Javed; Yancy, Clyde W; Fonarow, Gregg C

2015-09-01

Previous studies have shown that high levels of physical activity are associated with lower risk of risk factors for heart failure (HF), such as coronary heart disease, hypertension, and diabetes mellitus. However, the effects of physical activity or fitness on the incidence of HF remain unclear. MEDLINE and EMBASE were systematically searched until November 30, 2014. Prospective cohort studies reporting measures of the association of physical activity (n=10) or fitness (n=2) with incident HF were included. Extracted effect estimates from the eligible studies were pooled using a random-effects model meta-analysis, with heterogeneity assessed with the I(2) statistic. Ten cohort studies on physical activity eligible for meta-analysis included a total of 282 889 participants followed for 7 to 30 years. For the physical activity studies, maximum versus minimal amount of physical activity groups were used for analyses; with a total number of participants (n=165 695). The pooled relative risk (95% confidence interval [CI]) for HF among those with a regular exercise pattern was 0.72 (95% CI, 0.67-0.79). Findings were similar for men (0.71 [95% CI, 0.61-0.83]) and women (0.72 [95% CI, 0.67-0.77]) and by type of exercise. There was no evidence of publication bias (P value for Egger test=0.34). The pooled associated effect of physical fitness on incident HF was 0.79 (95% CI, 0.75-0.83) for each unit increase in metabolic equivalent of oxygen consumption. Published literature support a significant association between increased physical activity or fitness and decreased incidence of HF. © 2015 American Heart Association, Inc.

Classes of Heart Failure

MedlinePlus

... Class Objective Assessment A No objective evidence of cardiovascular disease. No symptoms and no limitation in ordinary physical activity. B Objective evidence of minimal cardiovascular disease. Mild symptoms and slight limitation during ordinary activity. ...

49 CFR 391.43 - Medical examination; certificate of physical examination.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., congestive heart failure, or cardiovascular disease that is accompanied by syncope, dyspnea, or collapse... ear disease, symptoms of aural vertigo, or Meniere's Syndrome. When recording hearing, record distance...

Children of Alcoholics

MedlinePlus

... drinking or other problem at home: • Failure in school; truancy • Lack of friends; withdrawal from classmates • Delinquent behavior, such as stealing or violence • Frequent physical complaints, such as headaches or stomachaches ...

Quality of life in patients receiving telemedicine enhanced chronic heart failure disease management: A meta-analysis.

PubMed

Knox, Liam; Rahman, Rachel J; Beedie, Chris

2017-08-01

Background Previous reviews have investigated the effectiveness of telemedicine in the treatment of heart failure (HF). Dependent variables have included hospitalisations, mortality rates, disease knowledge and health costs. Few reviews, however, have examined the variable of health-related quality of life (QoL). Methods Randomised controlled trials comparing the delivery methods of any form of telemedicine with usual care for the provision of HF disease-management were identified via searches of all relevant databases and reference lists. Studies had to report a quantitative measure for mental, physical or overall QoL in order to be included. Results A total of 33 studies were identified. However, poor reporting of data resulted in the exclusion of seven, leaving 26 studies with 7066 participants. Three separate, random effects meta-analyses were conducted for mental, physical and overall QoL. Telemedicine was not significantly more effective than usual care on mental and physical QoL (standardised mean difference (SMD) 0.03, (95% confidence interval (CI) -0.05-0.12), p = 0.45 and SMD 0.24, (95% CI -0.08-0.56), p = 0.14, respectively). However, when compared to usual care, telemedicine was associated with a small significant increase in overall QoL (SMD 0.23, (95% CI 0.09-0.37), p = 0.001). Moderator analyses indicated that telemedicine delivered over a long-duration (≥52 weeks) and via telemonitoring was most beneficial. Conclusion Compared to usual care, telemedicine significantly increases overall QoL in patients receiving HF disease management. Statistically non-significant but nonetheless positive trends were also observed for physical QoL. These findings provide preliminary support for the use of telemedicine in the management of heart failure without jeopardising patient well-being.

Exploring the Relationship Between Gender Violence and State Failure: A Cross-National Comparison.

PubMed

Gould, Laurie A; Agnich, Laura E

2016-10-01

The concept of state failure has only recently emerged in the political science and legal literature. Although state failure has been used to predict violent conflicts, and all citizens are affected by violence in failed/fragile states, women are especially at risk. Using data from the WomanStats project, this study's findings reveal that the physical security of women is lower in failed/fragile states compared with more sustainable nations. The characteristics of failed states that increase the likelihood of various forms of violence against women are identified, including high levels of militarization, countries with neighboring states at war, and massive movement of refugees. © The Author(s) 2016.

Probabilistic Design of a Mars Sample Return Earth Entry Vehicle Thermal Protection System

NASA Technical Reports Server (NTRS)

Dec, John A.; Mitcheltree, Robert A.

2002-01-01

The driving requirement for design of a Mars Sample Return mission is to assure containment of the returned samples. Designing to, and demonstrating compliance with, such a requirement requires physics based tools that establish the relationship between engineer's sizing margins and probabilities of failure. The traditional method of determining margins on ablative thermal protection systems, while conservative, provides little insight into the actual probability of an over-temperature during flight. The objective of this paper is to describe a new methodology for establishing margins on sizing the thermal protection system (TPS). Results of this Monte Carlo approach are compared with traditional methods.

The effective compliance of spatially evolving planar wing-cracks

NASA Astrophysics Data System (ADS)

Ayyagari, R. S.; Daphalapurkar, N. P.; Ramesh, K. T.

2018-02-01

We present an analytic closed form solution for anisotropic change in compliance due to the spatial evolution of planar wing-cracks in a material subjected to largely compressive loading. A fully three-dimensional anisotropic compliance tensor is defined and evaluated considering the wing-crack mechanism, using a mixed-approach based on kinematic and energetic arguments to derive the coefficients in incremental compliance. Material, kinematic and kinetic parametric influences on the increments in compliance are studied in order to understand their physical implications on material failure. Model verification is carried out through comparisons to experimental uniaxial compression results to showcase the predictive capabilities of the current study.

Gonococcal endocarditis in a 47-year-old Japanese man.

PubMed

Ito, Hiroshi; Miyazaki, Shinichi; Ozeki, Takaya; Matsuo, Masaki; Branch, Joel; Fujita, Yoshiro; Marui, Nobuyuki

2014-01-01

A 47-year-old sexually active Japanese man was admitted with a persistent fever and weight loss. A physical examination revealed a cardiac murmur. A transthoracic echocardiogram was nondiagnostic, although blood cultures grew Neisseria gonorrhoeae. Gonococcal endocarditis was diagnosed based on the modified Duke criteria. The administration of antimicrobial therapy resulted in an adequate initial resolution; however, two months after completing the therapy, the patient developed cardiac failure. Severe aortic regurgitation was identified, and the patient underwent emergent aortic valve replacement. Despite the rarity of gonococcal endocarditis, this disease should nevertheless be considered in patients presenting with a fever, cardiac murmur and a consistent sexual history.

The Effects of Climate Change on Cardiac Health.

PubMed

De Blois, Jonathan; Kjellstrom, Tord; Agewall, Stefan; Ezekowitz, Justin A; Armstrong, Paul W; Atar, Dan

2015-01-01

The earth's climate is changing and increasing ambient heat levels are emerging in large areas of the world. An important cause of this change is the anthropogenic emission of greenhouse gases. Climate changes have a variety of negative effects on health, including cardiac health. People with pre-existing medical conditions such as cardiovascular disease (including heart failure), people carrying out physically demanding work and the elderly are particularly vulnerable. This review evaluates the evidence base for the cardiac health consequences of climate conditions, with particular reference to increasing heat exposure, and it also explores the potential further implications. © 2015 S. Karger AG, Basel.

Associations of Intimate Partner Violence with Unintended Pregnancy and Pre-Pregnancy Contraceptive Use in South Asia

PubMed Central

Raj, Anita; McDougal, Lotus

2015-01-01

Objective To assess associations of intimate partner violence (IPV) with pregnancy intendedness and pre-pregnancy contraceptive use among pregnant women in South Asia. Study Design Cross-sectional analyses were conducted using most recent Demographic and Health Surveys (DHS) from Bangladesh, India and Nepal for married, pregnant women aged 15–49 years who responded to IPV assessments specific to current marriage (N=4738). Adjusted logistic and multinomial regression analyses were conducted with pooled data to assess associations of IPV ever (sexual only, physical only, sexual plus physical, none) with the outcomes of pregnancy intendedness (wanted, mistimed or unwanted) and pre-pregnancy contraceptive use (no, traditional, or modern), for the current pregnancy. Results IPV was not associated with a mistimed or unwanted pregnancy. Sexual IPV was associated with pre-pregnancy modern contraceptive use (aOR=2.32, 95% CI=1.24, 4.36); sexual plus physical IPV was associated with pre-pregnancy traditional contraceptive use (aOR=1.85, 95% CI=1.12, 3.07). Post-hoc analysis of reasons for pre-pregnancy contraceptive discontinuation revealed that women with a history of IPV, particularly sexual IPV, had higher prevalence of contraceptive failure (sexual only: 37.3%, sexual plus physical: 30.9%, physical only: 22.6%, no IPV: 13.6%). Conclusion Pregnant women who experienced sexual IPV from husbands were more likely to use contraceptives pre-pregnancy but had no reduced risk unintended pregnancy, possibly due to higher rates of pre-pregnancy contraceptive failure among those with this history. These findings suggest that victims of sexual IPV are able to acquire and use family planning services, but require more support to sustain effective contraceptive use. Implications Family planning services are reaching women affected by sexual IPV, and programs should be sensitive to this concern and the heightened vulnerability to contraceptive failure these women face. Long-acting reversible contraception could be beneficial by allowing women to have greater reproductive control in situations of compromised sexual autonomy. PMID:25769441

Associations of intimate partner violence with unintended pregnancy and pre-pregnancy contraceptive use in South Asia.

PubMed

Raj, Anita; McDougal, Lotus

2015-06-01

To assess associations of intimate partner violence (IPV) with pregnancy intendedness and pre-pregnancy contraceptive use among pregnant women in South Asia. Cross-sectional analyses were conducted using the most recent Demographic and Health Surveys from Bangladesh, India and Nepal for married, pregnant women aged 15-49 years who responded to IPV assessments specific to current marriage (N=4738). Adjusted logistic and multinomial regression analyses were conducted with pooled data to assess associations of IPV ever (sexual only, physical only, sexual plus physical or none) with the outcomes of pregnancy intendedness (wanted, mistimed or unwanted) and pre-pregnancy contraceptive use (no, traditional or modern) for the current pregnancy. IPV was not associated with a mistimed or unwanted pregnancy. Sexual IPV was associated with pre-pregnancy modern contraceptive use (aOR=2.32, 95% CI=1.24, 4.36); sexual plus physical IPV was associated with pre-pregnancy traditional contraceptive use (aOR=1.85, 95% CI=1.12, 3.07). Post hoc analysis of reasons for pre-pregnancy contraceptive discontinuation revealed that women with a history of IPV, particularly sexual IPV, had higher prevalence of contraceptive failure (sexual only, 37.3%; sexual plus physical, 30.9%; physical only, 22.6%; no IPV, 13.6%). Pregnant women who experienced sexual IPV from husbands were more likely to use contraceptives pre-pregnancy but had no reduced risk unintended pregnancy, possibly due to higher rates of pre-pregnancy contraceptive failure among those with this history. These findings suggest that victims of sexual IPV are able to acquire and use family planning services but require more support to sustain effective contraceptive use. Family planning services are reaching women affected by sexual IPV, and programs should be sensitive to this concern and the heightened vulnerability to contraceptive failure these women face. Long-acting reversible contraception could be beneficial by allowing women to have greater reproductive control in situations of compromised sexual autonomy. Copyright © 2015 Elsevier Inc. All rights reserved.

Failure probability analysis of optical grid

NASA Astrophysics Data System (ADS)

Zhong, Yaoquan; Guo, Wei; Sun, Weiqiang; Jin, Yaohui; Hu, Weisheng

2008-11-01

Optical grid, the integrated computing environment based on optical network, is expected to be an efficient infrastructure to support advanced data-intensive grid applications. In optical grid, the faults of both computational and network resources are inevitable due to the large scale and high complexity of the system. With the optical network based distributed computing systems extensive applied in the processing of data, the requirement of the application failure probability have been an important indicator of the quality of application and an important aspect the operators consider. This paper will present a task-based analysis method of the application failure probability in optical grid. Then the failure probability of the entire application can be quantified, and the performance of reducing application failure probability in different backup strategies can be compared, so that the different requirements of different clients can be satisfied according to the application failure probability respectively. In optical grid, when the application based DAG (directed acyclic graph) is executed in different backup strategies, the application failure probability and the application complete time is different. This paper will propose new multi-objective differentiated services algorithm (MDSA). New application scheduling algorithm can guarantee the requirement of the failure probability and improve the network resource utilization, realize a compromise between the network operator and the application submission. Then differentiated services can be achieved in optical grid.

A Weibull distribution accrual failure detector for cloud computing.

PubMed

Liu, Jiaxi; Wu, Zhibo; Wu, Jin; Dong, Jian; Zhao, Yao; Wen, Dongxin

2017-01-01

Failure detectors are used to build high availability distributed systems as the fundamental component. To meet the requirement of a complicated large-scale distributed system, accrual failure detectors that can adapt to multiple applications have been studied extensively. However, several implementations of accrual failure detectors do not adapt well to the cloud service environment. To solve this problem, a new accrual failure detector based on Weibull Distribution, called the Weibull Distribution Failure Detector, has been proposed specifically for cloud computing. It can adapt to the dynamic and unexpected network conditions in cloud computing. The performance of the Weibull Distribution Failure Detector is evaluated and compared based on public classical experiment data and cloud computing experiment data. The results show that the Weibull Distribution Failure Detector has better performance in terms of speed and accuracy in unstable scenarios, especially in cloud computing.

Risk Analysis of Earth-Rock Dam Failures Based on Fuzzy Event Tree Method

PubMed Central

Fu, Xiao; Gu, Chong-Shi; Su, Huai-Zhi; Qin, Xiang-Nan

2018-01-01

Earth-rock dams make up a large proportion of the dams in China, and their failures can induce great risks. In this paper, the risks associated with earth-rock dam failure are analyzed from two aspects: the probability of a dam failure and the resulting life loss. An event tree analysis method based on fuzzy set theory is proposed to calculate the dam failure probability. The life loss associated with dam failure is summarized and refined to be suitable for Chinese dams from previous studies. The proposed method and model are applied to one reservoir dam in Jiangxi province. Both engineering and non-engineering measures are proposed to reduce the risk. The risk analysis of the dam failure has essential significance for reducing dam failure probability and improving dam risk management level. PMID:29710824

Coexisting Frailty, Cognitive Impairment, and Heart Failure: Implications for Clinical Care

PubMed Central

Butts, Brittany; Gary, Rebecca

2015-01-01

Objective To review some of the proposed pathways that increase frailty risk in older persons with heart failure and to discuss tools that may be used to assess for changes in physical and cognitive functioning in this population in order to assist with appropriate and timely intervention. Methods Review of the literature. Results Heart failure is the only cardiovascular disease that is increasing by epidemic proportions, largely due to an aging society and therapeutic advances in disease management. Because heart failure is largely a cardiogeriatric syndrome, age-related syndromes such as frailty and cognitive impairment are common in heart failure patients. Compared with age-matched counterparts, older adults with heart failure 4 to 6 times more likely to be frail or cognitively impaired. The reason for the high prevalence of frailty and cognitive impairment in this population is not well known but may likely reflect the synergistic effects of heart failure and aging, which may heighten vulnerability to stressors and accelerate loss of physiologic reserve. Despite the high prevalence of frailty and cognitive impairment in the heart failure population, these conditions are not routinely screened for in clinical practice settings and guidelines on optimal assessment strategies are lacking. Conclusion Persons with heart failure are at an increased risk for frailty, which may worsen symptoms, impair self-management, and lead to worse heart failure outcomes. Early detection of frailty and cognitive impairment may be an opportunity for intervention and a key strategy for improving clinical outcomes in older adults with heart failure. PMID:26594103

A randomised controlled trial of a facilitated home-based rehabilitation intervention in patients with heart failure with preserved ejection fraction and their caregivers: the REACH-HFpEF Pilot Study.

PubMed

Lang, Chim C; Smith, Karen; Wingham, Jennifer; Eyre, Victoria; Greaves, Colin J; Warren, Fiona C; Green, Colin; Jolly, Kate; Davis, Russell C; Doherty, Patrick Joseph; Miles, Jackie; Britten, Nicky; Abraham, Charles; Van Lingen, Robin; Singh, Sally J; Paul, Kevin; Hillsdon, Melvyn; Sadler, Susannah; Hayward, Christopher; Dalal, Hayes M; Taylor, Rod S

2018-04-09

Home-based cardiac rehabilitation may overcome suboptimal rates of participation. The overarching aim of this study was to assess the feasibility and acceptability of the novel Rehabilitation EnAblement in CHronic Hear Failure (REACH-HF) rehabilitation intervention for patients with heart failure with preserved ejection fraction (HFpEF) and their caregivers. Patients were randomised 1:1 to REACH-HF intervention plus usual care (intervention group) or usual care alone (control group). REACH-HF is a home-based comprehensive self-management rehabilitation programme that comprises patient and carer manuals with supplementary tools, delivered by trained healthcare facilitators over a 12 week period. Patient outcomes were collected by blinded assessors at baseline, 3 months and 6 months postrandomisation and included health-related quality of life (primary) and psychological well-being, exercise capacity, physical activity and HF-related hospitalisation (secondary). Outcomes were also collected in caregivers.We enrolled 50 symptomatic patients with HF from Tayside, Scotland with a left ventricular ejection fraction ≥45% (mean age 73.9 years, 54% female, 100% white British) and 21 caregivers. Study retention (90%) and intervention uptake (92%) were excellent. At 6 months, data from 45 patients showed a potential direction of effect in favour of the intervention group, including the primary outcome of Minnesota Living with Heart Failure Questionnaire total score (between-group mean difference -11.5, 95% CI -22.8 to 0.3). A total of 11 (4 intervention, 7 control) patients experienced a hospital admission over the 6 months of follow-up with 4 (control patients) of these admissions being HF-related. Improvements were seen in a number intervention caregivers' mental health and burden compared with control. Our findings support the feasibility and rationale for delivering the REACH-HF facilitated home-based rehabilitation intervention for patients with HFpEF and their caregivers and progression to a full multicentre randomised clinical trial to test its clinical effectiveness and cost-effectiveness. ISRCTN78539530. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Eating Disorders

MedlinePlus

... medical illnesses. They often go along with other problems such as stress, anxiety, depression, and substance use. Eating disorders can lead to the development of serious physical health problems, such as heart conditions or kidney failure. Someone ...

Link importance incorporated failure probability measuring solution for multicast light-trees in elastic optical networks

NASA Astrophysics Data System (ADS)

Li, Xin; Zhang, Lu; Tang, Ying; Huang, Shanguo

2018-03-01

The light-tree-based optical multicasting (LT-OM) scheme provides a spectrum- and energy-efficient method to accommodate emerging multicast services. Some studies focus on the survivability technologies for LTs against a fixed number of link failures, such as single-link failure. However, a few studies involve failure probability constraints when building LTs. It is worth noting that each link of an LT plays different important roles under failure scenarios. When calculating the failure probability of an LT, the importance of its every link should be considered. We design a link importance incorporated failure probability measuring solution (LIFPMS) for multicast LTs under independent failure model and shared risk link group failure model. Based on the LIFPMS, we put forward the minimum failure probability (MFP) problem for the LT-OM scheme. Heuristic approaches are developed to address the MFP problem in elastic optical networks. Numerical results show that the LIFPMS provides an accurate metric for calculating the failure probability of multicast LTs and enhances the reliability of the LT-OM scheme while accommodating multicast services.

Is it beneficial to approximate pre-failure topography to predict landslide susceptibility with empirical models?

NASA Astrophysics Data System (ADS)

Steger, Stefan; Schmaltz, Elmar; Glade, Thomas

2017-04-01

Empirical landslide susceptibility maps spatially depict the areas where future slope failures are likely due to specific environmental conditions. The underlying statistical models are based on the assumption that future landsliding is likely to occur under similar circumstances (e.g. topographic conditions, lithology, land cover) as past slope failures. This principle is operationalized by applying a supervised classification approach (e.g. a regression model with a binary response: landslide presence/absence) that enables discrimination between conditions that favored past landslide occurrences and the circumstances typical for landslide absences. The derived empirical relation is then transferred to each spatial unit of an area. Literature reveals that the specific topographic conditions representative for landslide presences are frequently extracted from derivatives of digital terrain models at locations were past landslides were mapped. The underlying morphology-based landslide identification becomes possible due to the fact that the topography at a specific locality usually changes after landslide occurrence (e.g. hummocky surface, concave and steep scarp). In a strict sense, this implies that topographic predictors used within conventional statistical landslide susceptibility models relate to post-failure topographic conditions - and not to the required pre-failure situation. This study examines the assumption that models calibrated on the basis of post-failure topographies may not be appropriate to predict future landslide locations, because (i) post-failure and pre-failure topographic conditions may differ and (ii) areas were future landslides will occur do not yet exhibit such a distinct post-failure morphology. The study was conducted for an area located in the Walgau region (Vorarlberg, western Austria), where a detailed inventory consisting of shallow landslides was available. The methodology comprised multiple systematic comparisons of models generated on the basis of post-failure conditions (i.e. the standard approach) with models based on an approximated pre-failure topography. Pre-failure topography was approximated by (i) erasing the area of mapped landslide polygons within a digital terrain model and (ii) filling these "empty" areas by interpolating elevation points located outside the mapped landslides. Landslide presence information was extracted from the respective landslide scarp locations while an equal number of randomly sampled points represented landslide absences. After an initial exploratory data analysis, mixed-effects logistic regression was applied to model landslide susceptibility on the basis of two predictor sets (post-failure versus pre-failure predictors). Furthermore, all analyses were separately conducted for five different modelling resolutions to elaborate the suspicion that the degree of generalization of topographic parameters may as well play a role on how the respective models may differ. Model evaluation was conducted by means of multiple procedures (i.e. odds ratios, k-fold cross validation, permutation-based variable importance, difference maps of predictions). The results revealed that models based on highest resolutions (e.g. 1 m, 2.5 m) and post-failure topography performed best from a purely quantitative perspective. A confrontation of models (post-failure versus pre-failure based models) based on an identical modelling resolution exposed that validation results, modelled relationships as well as the prediction pattern tended to converge with a decreasing raster resolution. Based on the results, we concluded that an approximation of pre-failure topography does not significantly contribute to improved landslide susceptibility models in the case (i) the underlying inventory consists of small landslide features and (ii) the models are based on coarse raster resolutions (e.g. 25 m). However, in the case modelling with high raster resolutions is envisaged (e.g. 1 m, 2.5 m) or the inventory mainly consists of larger events, a reconstruction of pre-failure conditions might be highly expedient, even though conventional validation results might indicate an opposite tendency. Finally, we recommend to consider that topographic predictors highly useful to detect past slope movements (e.g. roughness) are not necessarily valuable to predict future slope instabilities.

Patterns of Self-care in Adults With Heart Failure and Their Associations With Sociodemographic and Clinical Characteristics, Quality of Life, and Hospitalizations: A Cluster Analysis.

PubMed

Vellone, Ercole; Fida, Roberta; Ghezzi, Valerio; D'Agostino, Fabio; Biagioli, Valentina; Paturzo, Marco; Strömberg, Anna; Alvaro, Rosaria; Jaarsma, Tiny

Self-care is important in heart failure (HF) treatment, but patients may have difficulties and be inconsistent in its performance. Inconsistencies in self-care behaviors may mirror patterns of self-care in HF patients that are worth identifying to provide interventions tailored to patients. The aims of this study are to identify clusters of HF patients in relation to self-care behaviors and to examine and compare the profile of each HF patient cluster considering the patient's sociodemographics, clinical variables, quality of life, and hospitalizations. This was a secondary analysis of data from a cross-sectional study in which we enrolled 1192 HF patients across Italy. A cluster analysis was used to identify clusters of patients based on the European Heart Failure Self-care Behaviour Scale factor scores. Analysis of variance and χ test were used to examine the characteristics of each cluster. Patients were 72.4 years old on average, and 58% were men. Four clusters of patients were identified: (1) high consistent adherence with high consulting behaviors, characterized by younger patients, with higher formal education and higher income, less clinically compromised, with the best physical and mental quality of life (QOL) and lowest hospitalization rates; (2) low consistent adherence with low consulting behaviors, characterized mainly by male patients, with lower formal education and lowest income, more clinically compromised, and worse mental QOL; (3) inconsistent adherence with low consulting behaviors, characterized by patients who were less likely to have a caregiver, with the longest illness duration, the highest number of prescribed medications, and the best mental QOL; (4) and inconsistent adherence with high consulting behaviors, characterized by patients who were mostly female, with lower formal education, worst cognitive impairment, worst physical and mental QOL, and higher hospitalization rates. The 4 clusters identified in this study and their associated characteristics could be used to tailor interventions aimed at improving self-care behaviors in HF patients.