The Development, Test, and Evaluation of Three Pilot Performance Reference Scales.

ERIC Educational Resources Information Center

Horner, Walter R.; And Others

A set of pilot performance reference scales was developed based upon airborne Audio-Video Recording (AVR) of student performance in T-37 undergraduate Pilot Training. After selection of the training maneuvers to be studied, video tape recordings of the maneuvers were selected from video tape recordings already available from a previous research…

TECHNOLOGY EVALUATION REPORT, SITE PROGRAM DEMONSTRATION TEST: SHIRCO PILOT-SCALE INFRARED INCINERATION SYSTEM ROSE TOWNSHIP DEMODE ROAD SUPERFUND SITE - VOLUME II

EPA Science Inventory

The performance of the Shirco pilot-scale infrared thermal destruction system has been evaluated at the Rose Township, Demode Road Superfund Site and is presented in the report. The waste tested consisted of solvents, organics and heavy metals in an illegal dump site. Volume I gi...

PILOT SCALE PROCESS EVALUATION OF REBURNING FOR IN-FURNACE NOX REDUCTION

EPA Science Inventory

The report gives results of coal and natural gas reburning application tests to a pilot scale 3.0 MWt furnace to provide the scaling information required for commercial application of reburning to pulverized-coal-fired boilers. Initial parametric studies had been conducted in a 2...

CSC Tip Sheets: Conducting and Evaluating Pilot Projects

EPA Pesticide Factsheets

Learn how to conduct and evaluate pilot projects, which are opportunities to “test the waters” for your project on a small scale, provide insight and data on what works, and adjust your strategy for full-scale implementation.

Scaling Down to Scale Up: A Health Economic Analysis of Integrating Point-of-Care Syphilis Testing into Antenatal Care in Zambia during Pilot and National Rollout Implementation

PubMed Central

Ncube, Alexander Tshaka; Sweeney, Sedona; Fleischer, Colette; Mumba, Grace Tembo; Gill, Michelle M.; Strasser, Susan; Peeling, Rosanna W.; Terris-Prestholt, Fern

2015-01-01

Maternal syphilis results in an estimated 500,000 stillbirths and neonatal deaths annually in Sub-Saharan Africa. Despite the existence of national guidelines for antenatal syphilis screening, syphilis testing is often limited by inadequate laboratory and staff services. Recent availability of inexpensive rapid point-of-care syphilis tests (RST) can improve access to antenatal syphilis screening. A 2010 pilot in Zambia explored the feasibility of integrating RST within prevention of mother-to-child-transmission of HIV services. Following successful demonstration, the Zambian Ministry of Health adopted RSTs into national policy in 2011. Cost data from the pilot and 2012 preliminary national rollout were extracted from project records, antenatal registers, clinic staff interviews, and facility observations, with the aim of assessing the cost and quality implications of scaling up a successful pilot into a national rollout. Start-up, capital, and recurrent cost inputs were collected, including costs of extensive supervision and quality monitoring during the pilot. Costs were analysed from a provider’s perspective, incremental to existing antenatal services. Total and unit costs were calculated and a multivariate sensitivity analysis was performed. Our accompanying qualitative study by Ansbro et al. (2015) elucidated quality assurance and supervisory system challenges experienced during rollout, which helped explain key cost drivers. The average unit cost per woman screened during rollout ($11.16) was more than triple the pilot unit cost ($3.19). While quality assurance costs were much lower during rollout, the increased unit costs can be attributed to several factors, including higher RST prices and lower RST coverage during rollout, which reduced economies of scale. Pilot and rollout cost drivers differed due to implementation decisions related to training, supervision, and quality assurance. This study explored the cost of integrating RST into antenatal care in pilot and national rollout settings, and highlighted important differences in costs that may be observed when moving from pilot to scale-up. PMID:25970443

Scaling Down to Scale Up: A Health Economic Analysis of Integrating Point-of-Care Syphilis Testing into Antenatal Care in Zambia during Pilot and National Rollout Implementation.

PubMed

Shelley, Katharine D; Ansbro, Éimhín M; Ncube, Alexander Tshaka; Sweeney, Sedona; Fleischer, Colette; Tembo Mumba, Grace; Gill, Michelle M; Strasser, Susan; Peeling, Rosanna W; Terris-Prestholt, Fern

2015-01-01

Maternal syphilis results in an estimated 500,000 stillbirths and neonatal deaths annually in Sub-Saharan Africa. Despite the existence of national guidelines for antenatal syphilis screening, syphilis testing is often limited by inadequate laboratory and staff services. Recent availability of inexpensive rapid point-of-care syphilis tests (RST) can improve access to antenatal syphilis screening. A 2010 pilot in Zambia explored the feasibility of integrating RST within prevention of mother-to-child-transmission of HIV services. Following successful demonstration, the Zambian Ministry of Health adopted RSTs into national policy in 2011. Cost data from the pilot and 2012 preliminary national rollout were extracted from project records, antenatal registers, clinic staff interviews, and facility observations, with the aim of assessing the cost and quality implications of scaling up a successful pilot into a national rollout. Start-up, capital, and recurrent cost inputs were collected, including costs of extensive supervision and quality monitoring during the pilot. Costs were analysed from a provider's perspective, incremental to existing antenatal services. Total and unit costs were calculated and a multivariate sensitivity analysis was performed. Our accompanying qualitative study by Ansbro et al. (2015) elucidated quality assurance and supervisory system challenges experienced during rollout, which helped explain key cost drivers. The average unit cost per woman screened during rollout ($11.16) was more than triple the pilot unit cost ($3.19). While quality assurance costs were much lower during rollout, the increased unit costs can be attributed to several factors, including higher RST prices and lower RST coverage during rollout, which reduced economies of scale. Pilot and rollout cost drivers differed due to implementation decisions related to training, supervision, and quality assurance. This study explored the cost of integrating RST into antenatal care in pilot and national rollout settings, and highlighted important differences in costs that may be observed when moving from pilot to scale-up.

UTILIZATION OF TREATABILITY AND PILOT TESTS TO PREDICT CAH BIOREMEDIATION

EPA Science Inventory

Multiple tools have been suggested to help in the design of enhanced anaerobic bioremediation systems for CAHs:
- Extensive high quality microcosm testing followed by small-scale, thoroughly observed field pilot tests (i.e., RABITT Protocol, Morse 1998)
- More limited ...

Smouldering Remediation (STAR) Technology: Field Pilot Tests and First Full Scale Application

NASA Astrophysics Data System (ADS)

Gerhard, J.; Kinsman, L.; Torero, J. L.

2015-12-01

STAR (Self-sustaining Treatment for Active Remediation) is an innovative remediation technology based on the principles of smoldering combustion where the contaminants are the fuel. The self-sustaining aspect means that a single, local ignition event can result in many days of contaminant destruction in situ. Presented research to date has focused on bench scale experiments, numerical modelling and process understanding. Presented here is the maturation of the in situ technology, including three field pilot tests and a full-scale implementation to treat coal tar-impacted soils. The first pilot determined a Radius of Influence (ROI) for a single ignition of approximately eight feet with an average propagation rate of the reaction of approximately one foot per day. TPH concentrations in soils were reduced from 10,000 milligrams per kilogram to a few hundred milligrams per kilogram. The second pilot was conducted in an area of significant void spaces created through the anthropogenic deposition of clay bricks and tiles. The void spaces led to pre-mature termination of the combustion reaction, limiting ROI and the effectiveness of the technology in this setting. The third case study involved the pilot testing, design, and full-scale implementation of STAR at a 37-acre former chemical manufacturing facility. Three phases of pilot testing were conducted within two hydrogeologic units at the site (i.e., surficial fill and deep alluvial sand units). Pilot testing within the fill demonstrated self-sustained coal tar destruction rates in excess of 800 kg/day supported through air injection at a single well. Deep sand unit testing (twenty-five feet below the water table) resulted in the treatment of a targeted six-foot layer of impacted fine sands to a radial distance of approximately twelve feet. These results (and additional parameters) were used to develop a full-scale STAR design consisting of approximately 1500 surficial fill ignition points and 500 deep sand ignition points and two treatment (air distribution and vapor collection / treatment) systems to remediate an approximately 14-acre footprint of contaminated soils within the project timelines (i.e., by mid-2016). Field activities began in 2014 and progress is currently on-schedule.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grigg, Reid; McPherson, Brian; Lee, Rober

The Southwest Regional Partnership on Carbon Sequestration (SWP) one of seven regional partnerships sponsored by the U.S. Department of Energy (USDOE) carried out five field pilot tests in its Phase II Carbon Sequestration Demonstration effort, to validate the most promising sequestration technologies and infrastructure concepts, including three geologic pilot tests and two terrestrial pilot programs. This field testing demonstrated the efficacy of proposed sequestration technologies to reduce or offset greenhouse gas emissions in the region. Risk mitigation, optimization of monitoring, verification, and accounting (MVA) protocols, and effective outreach and communication were additional critical goals of these field validation tests. Themore » program included geologic pilot tests located in Utah, New Mexico, Texas, and a region-wide terrestrial analysis. Each geologic sequestration test site was intended to include injection of a minimum of ~75,000 tons/year CO{sub 2}, with minimum injection duration of one year. These pilots represent medium- scale validation tests in sinks that host capacity for possible larger-scale sequestration operations in the future. These validation tests also demonstrated a broad variety of carbon sink targets and multiple value-added benefits, including testing of enhanced oil recovery and sequestration, enhanced coalbed methane production and a geologic sequestration test combined with a local terrestrial sequestration pilot. A regional terrestrial sequestration demonstration was also carried out, with a focus on improved terrestrial MVA methods and reporting approaches specific for the Southwest region.« less

Development of the Military Women's Attitudes Toward Menstrual Suppression Scale: from construct definition to pilot testing.

PubMed

Trego, Lori L

2009-01-01

The Military Women's Attitudes Toward Menstrual Suppression scale (MWATMS) was created to measure attitudes toward menstrual suppression during deployment. The human health and social ecology theories were integrated to conceptualize an instrument that accounts for military-unique aspects of the environment on attitudes toward suppression. A three-step instrument development process was followed to develop the MWATMS. The instrument was pilot tested on a convenience sample of 206 military women with deployment experience. Reliability was tested with measures of internal consistency (alpha = .97); validity was tested with principal components analysis with varimax rotation. Four components accounted for 65% of variance: Benefits/Interest, Hygiene, Convenience, and Soldier/Stress. The pilot test of the MWATMS supported its reliability and validity. Further testing is warranted for validation of this instrument.

EVALUATING CAPACITIES OF GAC PRELOADED WITH NATURAL WATER

EPA Science Inventory

Adsorption studies are conducted to determine how preloading a natural groundwater onto GAC affects the adsorption of cis-1,2-dichloroexthene in small-scale and pilot-scale columns. Capacities are determined from batch-isotherm tests, microcolumns, and pilot columns, which are p...

UTILIZATION OF TREATABILITY AND PILOT TESTS TO PREDICT CAH BIOREMEDIATION (Battelle)

EPA Science Inventory

Multiple tools have been suggested to help in the design of enhanced anaerobic bioremediation systems for CAHs:
Extensive high quality microcosm testing followed by small-scale, thoroughly observed, induced flow field pilot tests (i.e. RABITT Protocol, Morse 1998)
More...

Pilot-scale tests of HEME and HEPA dissolution process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qureshi, Z.H.; Strege, D.K.

A series of pilot-scale demonstration tests for the dissolution of High Efficiency Mist Eliminators (HEME`s) and High Efficiency Particulate Airfilters (HEPA) were performed on a 1/5th linear scale. These fiberglass filters are to be used in the Defense Waste Processing Facility (DWPF) to decontaminate the effluents from the off-gases generated during the feed preparation process and vitrification. When removed, these filters will be dissolved in the Decontamination Waste Treatment Tank (DWTT) using 5 wt% NaOH solution. The contaminated fiberglass is converted to an aqueous stream which will be transferred to the waste tanks. The filter metal structure will be rinsedmore » with process water before its disposal as low-level solid waste. The pilot-scale study reported here successfully demonstrated a simple one step process using 5 wt% NaOH solution. The proposed process requires the installation of a new water spray ring with 30 nozzles. In addition to the reduced waste generated, the total process time is reduced to 48 hours only (66% saving in time). The pilot-scale tests clearly demonstrated that the dissolution process of HEMEs has two stages - chemical digestion of the filter and mechanical erosion of the digested filter. The digestion is achieved by a boiling 5 wt% caustic solutions, whereas the mechanical break down of the digested filter is successfully achieved by spraying process water on the digested filter. An alternate method of breaking down the digested filter by increased air sparging of the solution was found to be marginally successful are best. The pilot-scale tests also demonstrated that the products of dissolution are easily pumpable by a centrifugal pump.« less

Thermochemical Users Facility | Bioenergy | NREL

Science.gov Websites

collaborate on research and development efforts or to use our equipment to test their materials and processes NREL's thermochemical process integration, scale-up, and piloting research. Schematic diagram of NRELs about NREL's thermochemical process integration, scale-up, and piloting research. Thermochemical

SCALE-UP OF RAPID SMALL-SCALE ADSORPTION TESTS TO FIELD-SCALE ADSORBERS: THEORETICAL AND EXPERIMENTAL BASIS

EPA Science Inventory

Design of full-scale adsorption systems typically includes expensive and time-consuming pilot studies to simulate full-scale adsorber performance. Accordingly, the rapid small-scale column test (RSSCT) was developed and evaluated experimentally. The RSSCT can simulate months of f...

Flight Testing the X-36: The Test Pilots Perspective

NASA Technical Reports Server (NTRS)

Walker, Laurence A.

1997-01-01

The X-36 is a 28% scale, remotely piloted research aircraft, designed to demonstrate tailless fighter agility. Powered by a modified Williams International F-112 jet engine, the X-36 uses thrust vectoring and a fly-by-wire control system. Although too small for an onboard pilot, a full-sized remote cockpit was designed to virtually place the test pilot into the aircraft using a variety of innovative techniques. To date, 22 flights have been flown, successfully completing the second phase of testing. Handling qualities have been matching predictions; the test operation is flown similarly to that for full sized manned aircraft. All takeoffs, test maneuvers and landings are flown by the test pilot, affording a greater degree of flexibility and the ability to handle the inevitable unknowns which may occur during highly experimental test programs. The cockpit environment, cues, and display techniques used in this effort have proven to enhance the 'virtual' test pilot's awareness and have helped ensure a successful RPV test program.

A pilot rating scale for evaluating failure transients in electronic flight control systems

NASA Technical Reports Server (NTRS)

Hindson, William S.; Schroeder, Jeffery A.; Eshow, Michelle M.

1990-01-01

A pilot rating scale was developed to describe the effects of transients in helicopter flight-control systems on safety-of-flight and on pilot recovery action. The scale was applied to the evaluation of hardovers that could potentially occur in the digital flight-control system being designed for a variable-stability UH-60A research helicopter. Tests were conducted in a large moving-base simulator and in flight. The results of the investigation were combined with existing airworthiness criteria to determine quantitative reliability design goals for the control system.

PILOT-SCALE DEMONSTRATION OF A SLURRY-PHASE BIOLOGICAL REACTOR FOR CREOSOTE-CONTAMINATED SOIL - APPLICATION ANALYSIS REPORT

EPA Science Inventory

In support of the U.S. Environmental Protection Agency’s (EPA) Superfund Innovative Technology Evaluation (SITE) Program, a pilot-scale demonstration of a slurry-phase bioremediation process was performed May 1991 at the EPA’s Test & Evaluation Facility in Cincinnati, OH. In this...

Measure Twice, Build Once: Bench-Scale Testing to Evaluate Bioretention Media Design

EPA Science Inventory

The paper discusses the utility of conducting bench-scale testing on selected bioretention media and media amendments to validate hydrologic properties before installing media and amendments in larger pilot- or full-scale rain garden installations. The bench-scale study conclude...

HANFORD MEDIUM-LOW CURIE WASTE PRETREATMENT ALTERNATIVES PROJECT FRACTIONAL CRYSTALLIZATION PILOT SCALE TESTING FINAL REPORT

DOE Office of Scientific and Technical Information (OSTI.GOV)

HERTING DL

2008-09-16

The Fractional Crystallization Pilot Plant was designed and constructed to demonstrate that fractional crystallization is a viable way to separate the high-level and low-activity radioactive waste streams from retrieved Hanford single-shell tank saltcake. The focus of this report is to review the design, construction, and testing details of the fractional crystallization pilot plant not previously disseminated.

Validation of laboratory-scale recycling test method of paper PSA label products

Treesearch

Carl Houtman; Karen Scallon; Richard Oldack

2008-01-01

Starting with test methods and a specification developed by the U.S. Postal Service (USPS) Environmentally Benign Pressure Sensitive Adhesive Postage Stamp Program, a laboratory-scale test method and a specification were developed and validated for pressure-sensitive adhesive labels, By comparing results from this new test method and pilot-scale tests, which have been...

[Spanish translation and cross-cultural adaptation of the ARMS-scale for measuring medication adherence in polypathological patients].

PubMed

González-Bueno, Javier; Calvo-Cidoncha, Elena; Sevilla-Sánchez, Daniel; Espaulella-Panicot, Joan; Codina-Jané, Carles; Santos-Ramos, Bernardo

2017-10-01

Translate the ARMS scale into Spanish ensuring cross-cultural equivalence for measuring medication adherence in polypathological patients. Translation, cross-cultural adaptation and pilot testing. Secondary hospital. (i)Forward and blind-back translations followed by cross-cultural adaptation through qualitative methodology to ensure conceptual, semantic and content equivalence between the original scale and the Spanish version. (ii)Pilot testing in non-institutionalized polypathological patients to assess the instrument for clarity. The Spanish version of the ARMS scale has been obtained. Overall scores from translators involved in forward and blind-back translations were consistent with a low difficulty for assuring conceptual equivalence between both languages. Pilot testing (cognitive debriefing) in a sample of 40 non-institutionalized polypathological patients admitted to an internal medicine department of a secondary hospital showed an excellent clarity. The ARMS-e scale is a Spanish-adapted version of the ARMS scale, suitable for measuring adherence in polypathological patients. Its structure enables a multidimensional approach of the lack of adherence allowing the implementation of individualized interventions guided by the barriers detected in every patient. Copyright © 2017 Elsevier España, S.L.U. All rights reserved.

DEMONSTRATION OF PILOT-SCALE PERVAPORATION SYSTEMS FOR VOLATILE ORGANIC COMPOUND REMOVAL FROM A SURFACTANT ENHANCED AQUIFER REMEDIATION FLUID. II. HOLLOW FIBER MEMBRANE MODULES

EPA Science Inventory

Pilot-scale demonstration of pervaporation-based removal of volatile organic compounds from a surfactant enhanced aquifer remediation (SEAR) fluid has been conducted at USEPA's Test & Evaluation Facility using hollow fiber membrane modules. The membranes consisted of microporous...

PILOT PLANT TESTING OF ELEMENTAL MERCURY RE-EMISSION FROM WET SCRUBBERS

EPA Science Inventory

A pilot-scale wet lime/limestone flue gas desulfurization scrubber system was designed to conduct mercury emission control research. The first tests focused on investigating the phenomenon of Hgo re-emission from wet scrubbers with a specific objective of developing a Hgo re-emis...

Assessing Arsenic Removal by Metal (Hydr)Oxide Adsorptive Media Using Rapid Small Scale Column Tests

EPA Science Inventory

The rapid small scale column test (RSSCT) was use to evaluate the the performance of eight commercially available adsorptive media for the removal of arsenic. Side-by-side tests were conducted using RSSCTs and pilot/full-scale systems either in the field or in the laboratory. ...

Fighter pilots' heart rate, heart rate variation and performance during an instrument flight rules proficiency test.

PubMed

Mansikka, Heikki; Virtanen, Kai; Harris, Don; Simola, Petteri

2016-09-01

Increased task demand will increase the pilot mental workload (PMWL). When PMWL is increased, mental overload may occur resulting in degraded performance. During pilots' instrument flight rules (IFR) proficiency test, PMWL is typically not measured. Therefore, little is known about workload during the proficiency test and pilots' potential to cope with higher task demands than those experienced during the test. In this study, fighter pilots' performance and PMWL was measured during a real IFR proficiency test in an F/A-18 simulator. PMWL was measured using heart rate (HR) and heart rate variation (HRV). Performance was rated using Finnish Air Force's official rating scales. Results indicated that HR and HRV differentiate varying task demands in situations where variations in performance are insignificant. It was concluded that during a proficiency test, PMWL should be measured together with the task performance measurement. Copyright © 2016 Elsevier Ltd. All rights reserved.

Latent Profile Analyses of Test Anxiety: A Pilot Study

ERIC Educational Resources Information Center

von der Embse, Nathaniel P.; Mata, Andrea D.; Segool, Natasha; Scott, Emma-Catherine

2014-01-01

In an era of test-based accountability, there has been a renewed interest in understanding the relationship between test anxiety and test performance. The development and validation of test anxiety scales have grown with the rise of test anxiety research. Research is needed to critically examine the psychometric properties of these scales prior to…

Development of a Dynamically Scaled Generic Transport Model Testbed for Flight Research Experiments

NASA Technical Reports Server (NTRS)

Jordan, Thomas; Langford, William; Belcastro, Christine; Foster, John; Shah, Gautam; Howland, Gregory; Kidd, Reggie

2004-01-01

This paper details the design and development of the Airborne Subscale Transport Aircraft Research (AirSTAR) test-bed at NASA Langley Research Center (LaRC). The aircraft is a 5.5% dynamically scaled, remotely piloted, twin-turbine, swept wing, Generic Transport Model (GTM) which will be used to provide an experimental flight test capability for research experiments pertaining to dynamics modeling and control beyond the normal flight envelope. The unique design challenges arising from the dimensional, weight, dynamic (inertial), and actuator scaling requirements necessitated by the research community are described along with the specific telemetry and control issues associated with a remotely piloted subscale research aircraft. Development of the necessary operational infrastructure, including operational and safety procedures, test site identification, and research pilots is also discussed. The GTM is a unique vehicle that provides significant research capacity due to its scaling, data gathering, and control characteristics. By combining data from this testbed with full-scale flight and accident data, wind tunnel data, and simulation results, NASA will advance and validate control upset prevention and recovery technologies for transport aircraft, thereby reducing vehicle loss-of-control accidents resulting from adverse and upset conditions.

THE U.S. ENVIRONMENTAL PROTECTION AGENCY'S SITE EMERGING TECHNOLOGY PROGRAM

EPA Science Inventory

Under the SITE Emerging Technology Program, the U.S. Environmental Protection Agency is seeking to foster the further development of technol- ogies that have been successfully tested at bench-scale and are now ready for pilot-scale testing, prior to field- or full-scale demonstra...

Early language screening in city and Hackney: the concurrent validity of a measure designed for use with 2 1/2-year-olds.

PubMed

Law, J

1994-01-01

This paper reports data relating to the development of a screening test for language impairment in 2 1/2-year-old children. The screening test itself has previously been described. The results of a pilot study and a larger community study are reported. In all, 34 children were included in the pilot study and 1015 in the community study. The reference test selected was the Reynell Developmental Language Scales and the cut-off adopted 1.5 standard deviations below the mean for either the expressive or the receptive scale of the test concerned. The pass mark on the screening test was ascertained using receiver operating characteristics (ROC). The validity is reported given the cut-off identified. The specificity, sensitivity and both positive and negative predictive abilities are reported for both the pilot and the subsequent study. The application of the test is discussed in the context of the current debate about early identification.

40 CFR 264.17 - General requirements for ignitable, reactive, or incompatible wastes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (e.g., from heat-producing chemical reactions), and radiant heat. While ignitable or reactive waste... scientific or engineering literature, data from trial tests (e.g., bench scale or pilot scale tests), waste...

PILOT-SCALE PARAMETRIC TESTING OF SPRAY DRYER SO2 SCRUBBER FOR LOW-TO-MODERATE SULFUR COAL UTILITY APPLICATIONS

EPA Science Inventory

The report gives results of a comprehensive, pilot, dry, SO2 scrubbing test program to determine the effects of process variables on SO2 removal. In the spray dryer, stoichiometric ratio, flue gas temperature approach to adiabatic saturation, and temperature drop across the spray...

Measuring the Immeasurable: A Pilot Study of Museum Effectiveness.

ERIC Educational Resources Information Center

Borun, Minda

The report describes a one-year pilot study of museum effectiveness conducted at the Franklin Institute Science Museum and Planetarium in Philadelphia. The study was intended to develop models for testing visitor response, provide useable information to museum staff, and test the feasibility of a large-scale investigation of science museums.…

Solar photocatalytic degradation of some hazardous water-soluble pesticides at pilot-plant scale.

PubMed

Oller, I; Gernjak, W; Maldonado, M I; Pérez-Estrada, L A; Sánchez-Pérez, J A; Malato, S

2006-12-01

The technical feasibility and performance of photocatalytic degradation of six water-soluble pesticides (cymoxanil, methomyl, oxamyl, dimethoate, pyrimethanil and telone) have been studied at pilot-plant scale in two well-defined systems which are of special interest because natural solar UV light can be used: heterogeneous photocatalysis with titanium dioxide and homogeneous photocatalysis by photo-Fenton. TiO(2) photocatalysis tests were performed in a 35L solar pilot plant with three Compound Parabolic Collectors (CPCs) under natural illumination and a 75L solar pilot plant with four CPC units was used for homogeneous photocatalysis tests. The initial pesticide concentration studied was 50 mg L(-1) and the catalyst concentrations employed were 200 mg L(-1) of TiO(2) and 20 mg L(-1) of iron. Both toxicity (Vibrio fischeri, Biofix) and biodegradability (Zahn-Wellens test) of the initial pesticide solutions were also measured. Total disappearance of the parent compounds and nearly complete mineralization were attained with all pesticides tested. Treatment time, hydrogen peroxide consumption and release of heteroatoms are discussed.

Officer Career Development: Longitudinal Sample--Fiscal Years 1986-1987

DTIC Science & Technology

1991-10-01

XO-Fleet Replacement Squadron (RAG) 4. CO-Fleet Replacement Squadron (RAG) 5. Test Pilot School 6. Washington Tour 7. Wing Staff 8. Naval Aviation...2535 4. CO -RAG E9E6 - - - - - - - 1 2536 5. Test Pilot E9E7 - - - - - - - 1 2537 6. Wash. Tour E9E9 - - - - - - - 1 2538 1. Wing Staff E9E1O - 2539...for department head (VP community only) 12. Screening for Test Pilot school (omit if not applicable) RESPONSE SCALE: 1. Little Or No Change 2. 3. A

Evaluation and Testing of IONSIV IE-911 for the Removal of Cesium-137 from INEEL Tank Waste and Dissolved Calcines

DOE Office of Scientific and Technical Information (OSTI.GOV)

N. R. Mann; T. A. Todd; K. N. Brewer

1999-04-01

Development of waste treatment processes for the remediation of radioactive wastes is currently underway. A number of experiments were performed at the Idaho Nuclear Technology and Environmental Center (INTEC) located at the Idaho National Engineering and Environmental Laboratory (INEEL) with the commercially available sorbent material, IONSIV IE-911, crystalline silicotitanate (CST), manufactured by UOP LLC. The purpose of this work was to evaluate the removal efficiency, sorbent capacity and selectivity of CST for removing Cs-137 from actual and simulated acidic tank waste in addition to dissolved pilot-plant calcine solutions. The scope of this work included batch contact tests performed with non-radioactivemore » dissolved Al and Run-64 pilot plant calcines in addition to simulants representing the average composition of tank waste. Small-scale column tests were performed with actual INEEL tank WM-183 waste, tank waste simulant, dissolved Al and Run-64 pilot plant calcine solutions. Small-scale column experiments using actual WM-183 tank waste resulted in fifty-percent Cs-137 breakthrough at approximately 589 bed volumes. Small-scale column experiments using the tank waste simulant displayed fifty-percent Cs-137 breakthrough at approximately 700 bed volumes. Small-scale column experiments using dissolved Al calcine simulant displayed fifty-percent Cs-137 breakthrough at approximately 795 bed volumes. Column experiments with dissolved Run-64, pilot plant calcine did not reach fifty-percent breakthrough throughout the test.« less

Development of the Attributed Dignity Scale.

PubMed

Jacelon, Cynthia S; Dixon, Jane; Knafl, Kathleen A

2009-07-01

A sequential, multi-method approach to instrument development beginning with concept analysis, followed by (a) item generation from qualitative data, (b) review of items by expert and lay person panels, (c) cognitive appraisal interviews, (d) pilot testing, and (e) evaluating construct validity was used to develop a measure of attributed dignity in older adults. The resulting positively scored, 23-item scale has three dimensions: Self-Value, Behavioral Respect-Self, and Behavioral Respect-Others. Item-total correlations in the pilot study ranged from 0.39 to 0.85. Correlations between the Attributed Dignity Scale (ADS) and both Rosenberg's Self-Esteem Scale (0.17) and Crowne and Marlowe's Social Desirability Scale (0.36) were modest and in the expected direction, indicating attributed dignity is a related but independent concept. Next steps include testing the ADS with a larger sample to complete factor analysis, test-retest stability, and further study of the relationships between attributed dignity and other concepts.

Transformation of Bisphenol A in Water Distribution Systems, A Pilot-scale Study

EPA Science Inventory

Halogenations of bisphenol A (BPA) in a pilot-scale water distribution system (WDS) of cement-lined ductile cast iron pipe were investigated under the condition: pH 7.3±0.3, water flow velocity of 1.0 m/s, and 25 °C ± 1 °C in water temperature. The testing water was chlorinated f...

Commissioning Source and Personality Differences in U.S. Air Force Pilot Training

DTIC Science & Technology

2012-09-24

Narcissistic Personality Disorder and Histrionic Personality Disorder. The two tests generally converged, showing student pilots as socially outgoing...Histrionic, Narcissistic , and Antisocial scales of the MCMI. Cluster two students scored high on the Achievement, Affiliation, Endurance, and Social...Desirability scales but low on Dependence. In addition, they had moderate Narcissistic and Histrionic scores and high Compulsive Personality Disorder

Pilot-scale testing of renewable biocatalyst for swine manure treatment and mitigation of odorous VOCs, ammonia and hydrogen sulfide emissions

USDA-ARS?s Scientific Manuscript database

Comprehensive control of odors, hydrogen sulfide (H2S), ammonia (NH3), and greenhouse gas (GHG) emissions associated with swine production is a critical need. A pilot-scale experiment was conducted to evaluate the topical application of soybean peroxidase (SBP) and calcium peroxide (CaO2) as a manu...

National Alliance for Advance Biofuels and Bio-Products Final Technical Report Addendum Hydrothermal Processing Pilot System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oyler, James R.

2015-12-21

The main objective of the NAABB was to combine science, technology, and engineering expertise from across the nation to break down critical technical barriers to commercialization of algae-based biofuels. As a part of the consortium, Genifuel’s NAABB goals was to fabricate and demonstrate a pilot-scale system to convert algae into fuels. The purpose of this pilot system was to show that processes developed in the laboratory at bench-scale during the program could be successfully scaled up to a pre-commercial level, and thereby provide visibility into the ultimate viability and cost of algae biofuels. The pilot system has now been completedmore » and tested, and this report documents what has been achieved.« less

Introduction of Syphilis Point-of-Care Tests, from Pilot Study to National Programme Implementation in Zambia: A Qualitative Study of Healthcare Workers' Perspectives on Testing, Training and Quality Assurance.

PubMed

Ansbro, Éimhín M; Gill, Michelle M; Reynolds, Joanna; Shelley, Katharine D; Strasser, Susan; Sripipatana, Tabitha; Tshaka Ncube, Alexander; Tembo Mumba, Grace; Terris-Prestholt, Fern; Peeling, Rosanna W; Mabey, David

2015-01-01

Syphilis affects 1.4 million pregnant women globally each year. Maternal syphilis causes congenital syphilis in over half of affected pregnancies, leading to early foetal loss, pregnancy complications, stillbirth and neonatal death. Syphilis is under-diagnosed in pregnant women. Point-of-care rapid syphilis tests (RST) allow for same-day treatment and address logistical barriers to testing encountered with standard Rapid Plasma Reagin testing. Recent literature emphasises successful introduction of new health technologies requires healthcare worker (HCW) acceptance, effective training, quality monitoring and robust health systems. Following a successful pilot, the Zambian Ministry of Health (MoH) adopted RST into policy, integrating them into prevention of mother-to-child transmission of HIV clinics in four underserved Zambian districts. We compare HCW experiences, including challenges encountered in scaling up from a highly supported NGO-led pilot to a large-scale MoH-led national programme. Questionnaires were administered through structured interviews of 16 HCWs in two pilot districts and 24 HCWs in two different rollout districts. Supplementary data were gathered via stakeholder interviews, clinic registers and supervisory visits. Using a conceptual framework adapted from health technology literature, we explored RST acceptance and usability. Quantitative data were analysed using descriptive statistics. Key themes in qualitative data were explored using template analysis. Overall, HCWs accepted RST as learnable, suitable, effective tools to improve antenatal services, which were usable in diverse clinical settings. Changes in training, supervision and quality monitoring models between pilot and rollout may have influenced rollout HCW acceptance and compromised testing quality. While quality monitoring was integrated into national policy and training, implementation was limited during rollout despite financial support and mentorship. We illustrate that new health technology pilot research can rapidly translate into policy change and scale-up. However, training, supervision and quality assurance models should be reviewed and strengthened as rollout of the Zambian RST programme continues.

Introduction of Syphilis Point-of-Care Tests, from Pilot Study to National Programme Implementation in Zambia: A Qualitative Study of Healthcare Workers’ Perspectives on Testing, Training and Quality Assurance

PubMed Central

Ansbro, Éimhín M.; Gill, Michelle M.; Reynolds, Joanna; Shelley, Katharine D.; Strasser, Susan; Sripipatana, Tabitha; Ncube, Alexander Tshaka; Tembo Mumba, Grace; Terris-Prestholt, Fern; Peeling, Rosanna W.; Mabey, David

2015-01-01

Syphilis affects 1.4 million pregnant women globally each year. Maternal syphilis causes congenital syphilis in over half of affected pregnancies, leading to early foetal loss, pregnancy complications, stillbirth and neonatal death. Syphilis is under-diagnosed in pregnant women. Point-of-care rapid syphilis tests (RST) allow for same-day treatment and address logistical barriers to testing encountered with standard Rapid Plasma Reagin testing. Recent literature emphasises successful introduction of new health technologies requires healthcare worker (HCW) acceptance, effective training, quality monitoring and robust health systems. Following a successful pilot, the Zambian Ministry of Health (MoH) adopted RST into policy, integrating them into prevention of mother-to-child transmission of HIV clinics in four underserved Zambian districts. We compare HCW experiences, including challenges encountered in scaling up from a highly supported NGO-led pilot to a large-scale MoH-led national programme. Questionnaires were administered through structured interviews of 16 HCWs in two pilot districts and 24 HCWs in two different rollout districts. Supplementary data were gathered via stakeholder interviews, clinic registers and supervisory visits. Using a conceptual framework adapted from health technology literature, we explored RST acceptance and usability. Quantitative data were analysed using descriptive statistics. Key themes in qualitative data were explored using template analysis. Overall, HCWs accepted RST as learnable, suitable, effective tools to improve antenatal services, which were usable in diverse clinical settings. Changes in training, supervision and quality monitoring models between pilot and rollout may have influenced rollout HCW acceptance and compromised testing quality. While quality monitoring was integrated into national policy and training, implementation was limited during rollout despite financial support and mentorship. We illustrate that new health technology pilot research can rapidly translate into policy change and scale-up. However, training, supervision and quality assurance models should be reviewed and strengthened as rollout of the Zambian RST programme continues. PMID:26030741

The Development and Psychometric Properties of the Immigration Law Concerns Scale (ILCS) for HIV Testing.

PubMed

Lechuga, Julia; Galletly, Carol L; Broaddus, Michelle R; Dickson-Gomez, Julia B; Glasman, Laura R; McAuliffe, Timothy L; Vega, Miriam Y; LeGrand, Sarah; Mena, Carla A; Barlow, Morgan L; Valera, Erik; Montenegro, Judith I

2017-11-08

To develop, pilot test, and conduct psychometric analyses of an innovative scale measuring the influence of perceived immigration laws on Latino migrants' HIV-testing behavior. The Immigration Law Concerns Scale (ILCS) was developed in three phases: Phase 1 involved a review of law and literature, generation of scale items, consultation with project advisors, and subsequent revision of the scale. Phase 2 involved systematic translation- back translation and consensus-based editorial processes conducted by members of a bilingual and multi-national study team. In Phase 3, 339 sexually active, HIV-negative Spanish-speaking, non-citizen Latino migrant adults (both documented and undocumented) completed the scale via audio computer-assisted self-interview. The psychometric properties of the scale were tested with exploratory factor analysis and estimates of reliability coefficients were generated. Bivariate correlations were conducted to test the discriminant and predictive validity of identified factors. Exploratory factor analysis revealed a three-factor, 17-item scale. subscale reliability ranged from 0.72 to 0.79. There were significant associations between the ILCS and the HIV-testing behaviors of participants. Results of the pilot test and psychometric analysis of the ILCS are promising. The scale is reliable and significantly associated with the HIV-testing behaviors of participants. Subscales related to unwanted government attention and concerns about meeting moral character requirements should be refined.

RESEARCH IN FILTRATION FOR CRYPTOSPORIDIUM REMOVAL

EPA Science Inventory

The USEPA has conducted pilot plant studies for the removal of Cryptosporidium oocysts from drinking water. Fourteen pilot-scale tests were performed to assess the ability of conventional treatment to control Cryptosporidium oocysts and three surrogates; turbidity, total particle...

Creative use of pilot points to address site and regional scale heterogeneity in a variable-density model

USGS Publications Warehouse

Dausman, Alyssa M.; Doherty, John; Langevin, Christian D.

2010-01-01

Pilot points for parameter estimation were creatively used to address heterogeneity at both the well field and regional scales in a variable-density groundwater flow and solute transport model designed to test multiple hypotheses for upward migration of fresh effluent injected into a highly transmissive saline carbonate aquifer. Two sets of pilot points were used within in multiple model layers, with one set of inner pilot points (totaling 158) having high spatial density to represent hydraulic conductivity at the site, while a second set of outer points (totaling 36) of lower spatial density was used to represent hydraulic conductivity further from the site. Use of a lower spatial density outside the site allowed (1) the total number of pilot points to be reduced while maintaining flexibility to accommodate heterogeneity at different scales, and (2) development of a model with greater areal extent in order to simulate proper boundary conditions that have a limited effect on the area of interest. The parameters associated with the inner pilot points were log transformed hydraulic conductivity multipliers of the conductivity field obtained by interpolation from outer pilot points. The use of this dual inner-outer scale parameterization (with inner parameters constituting multipliers for outer parameters) allowed smooth transition of hydraulic conductivity from the site scale, where greater spatial variability of hydraulic properties exists, to the regional scale where less spatial variability was necessary for model calibration. While the model is highly parameterized to accommodate potential aquifer heterogeneity, the total number of pilot points is kept at a minimum to enable reasonable calibration run times.

Pilot-scale treatability test plan for the 200-BP-5 operable unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This document presents the treatability test plan for pilot-scale pump and treat testing at the 200-BP-5 Operable Unit. This treatability test plan has been prepared in response to an agreement between the U.S. Department of Energy (DOE), the U.S. Environmental Protection Agency (EPA), and the State of Washington Department of Ecology (Ecology), as documented in Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement, Ecology et al. 1989a) Change Control Form M-13-93-03 (Ecology et al. 1994) and a recent 200 NPL Agreement Change Control Form (Appendix A). The agreement also requires that, following completion of the activities described in thismore » test plan, a 200-BP-5 Operable Unit Interim Remedial Measure (IRM) Proposed Plan be developed for use in preparing an Interim Action Record of Decision (ROD). The IRM Proposed Plan will be supported by the results of this treatability test plan, as well as by other 200-BP-5 Operable Unit activities (e.g., development of a qualitative risk assessment). Once issued, the Interim Action ROD will specify the interim action(s) for groundwater contamination at the 200-BP-5 Operable Unit. The treatability test approach is to conduct a pilot-scale pump and treat test for each of the two contaminant plumes associated with the 200-BP-5 Operable Unit. Primary contaminants of concern are {sup 99}Tc and {sup 60}Co for underwater affected by past discharges to the 216-BY Cribs, and {sup 90}Sr, {sup 239/240}Pu, and Cs for groundwater affected by past discharges to the 216-B-5 Reverse Well. The purpose of the pilot-scale treatability testing presented in this testplan is to provide the data basis for preparing an IRM Proposed Plan. To achieve this objective, treatability testing must: Assess the performance of groundwater pumping with respect to the ability to extract a significant amount of the primary contaminant mass present in the two contaminant plumes.« less

Evaluation of several biological monitoring techniques for hazard assessment of potentially contaminated wastewater and groundwater. Volume 3. Old O-field groundwater. Final report, July 1990-December 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burton, D.T.; Turley, S.D.

1992-03-01

The toxicity of contaminated Old O-Field (Edgewood Area of Aberdeen Proving Ground) groundwater and the reduction and/or elimination of toxicity by various treatment processes were evaluated. The study was divided into a bench scale and pilot scale study. The bench scale studies consisted of 48-h definitive acute toxicity tests run with daphnid neonates (Daphnia magna) and juvenile fathead minnows (Pimephales promelas) exposed to untreated Old O-Field groundwater and groundwater treated by metals precipitation, UV oxidation (H 2O2 ), carbon adsorption, and carbon adsorption/biological sludge. The pilot scale studies consisted of several 96-h definitive acute toxicity tests run with two freshwatermore » and two saltwater invertebrates and fish and Ames mutagenicity assays. Acute toxicity tests were run on untreated Old O-Field groundwater and groundwater treated by metals precipitation, UV oxidation (H2O2), air stripping, and carbon adsorption during the pilot scale study. The freshwater invertebrate and fish used in the study were daphnid neonates and juvenile fathead minnows, respectively. The saltwater invertebrate and fish were juvenile mysids (Mysidopsis bahia) and juvenile sheepshead minnows (Cyprinodon variegatus). Ames tests were run on untreated groundwater, UV oxidation-treated groundwater, and carbon-treated groundwater.... Groundwater, Aquatic, Toxicity, Daphnia, Daphnia magna, Fathead minnow, Pimephales promelas, Mysid, Mysidopsis bahia, Sheepshead minnow, Cyprinodon variegatus.« less

Binary constructs of forensic psychiatric nursing: a pilot study.

PubMed

Mason, T; Dulson, J; King, L

2009-03-01

The aim was to develop an Information Gathering Schedule (IGS) relevant to forensic psychiatric nursing in order to establish the perceived differences in the three levels of security, high, medium and low. Perceived differences in the role constructs of forensic psychiatric nursing is said to exist but the evidence is qualitative or anecdotal. This paper sets out a pilot study beginning in 2004 relating to the development of two rating scales for inclusion into an IGS to acquire data on the role constructs of nurses working in these environments. Following a thematic analysis from the literature two sets of binary frameworks were constructed and a number of questions/statements relating to them were tested. The Thurstone Scaling test was applied to compute medians resulting in a reduction to 48 and 20 items for each respective framework. Two 7-point Likert scales were constructed and test-retest procedures were applied on a sample population of forensic psychiatric nurses. Student's t-test was conducted on the data and the results suggest that the IGS is now suitable for application on a larger study. The IGS was piloted on a small sample of forensic psychiatric nurses. The two scales were validated to coefficient values ranging from 0.7 to 0.9. Amendments were made and the IGS was considered acceptable.

Development and initial validation of the appropriate antibiotic use self-efficacy scale.

PubMed

Hill, Erin M; Watkins, Kaitlin

2018-06-04

While there are various medication self-efficacy scales that exist, none assess self-efficacy for appropriate antibiotic use. The Appropriate Antibiotic Use Self-Efficacy Scale (AAUSES) was developed, pilot tested, and its psychometric properties were examined. Following pilot testing of the scale, a 28-item questionnaire was examined using a sample (n = 289) recruited through the Amazon Mechanical Turk platform. Participants also completed other scales and items, which were used in assessing discriminant, convergent, and criterion-related validity. Test-retest reliability was also examined. After examining the scale and removing items that did not assess appropriate antibiotic use, an exploratory factor analysis was conducted on 13 items from the original scale. Three factors were retained that explained 65.51% of the variance. The scale and its subscales had adequate internal consistency. The scale had excellent test-retest reliability, as well as demonstrated convergent, discriminant, and criterion-related validity. The AAUSES is a valid and reliable scale that assesses three domains of appropriate antibiotic use self-efficacy. The AAUSES may have utility in clinical and research settings in understanding individuals' beliefs about appropriate antibiotic use and related behavioral correlates. Future research is needed to examine the scale's utility in these settings. Copyright © 2018 Elsevier B.V. All rights reserved.

Scaled Composites' Proteus aircraft and an F/A-18 Hornet from NASA's Dryden Flight Research Center d

NASA Technical Reports Server (NTRS)

2002-01-01

Scaled Composites' Proteus aircraft and an F/A-18 Hornet from NASA's Dryden Flight Research Center during a low-level flyby at Las Cruces Airport in New Mexico. The unique Proteus aircraft served as a test bed for NASA-sponsored flight tests designed to validate collision-avoidance technologies proposed for uninhabited aircraft. The tests, flown over southern New Mexico in March, 2002, used the Proteus as a surrogate uninhabited aerial vehicle (UAV) while three other aircraft flew toward the Proteus from various angles on simulated collision courses. Radio-based 'detect, see and avoid' equipment on the Proteus successfully detected the other aircraft and relayed that information to a remote pilot on the ground at Las Cruces Airport. The pilot then transmitted commands to the Proteus to maneuver it away from the potential collisions. The flight demonstration, sponsored by NASA Dryden Flight Research Center, New Mexico State University, Scaled Composites, the U.S. Navy and Modern Technology Solutions, Inc., were intended to demonstrate that UAVs can be flown safely and compatibly in the same skies as piloted aircraft.

Initial test of large panels of structural flakeboard from southern hardwoods

Treesearch

Eddie W. Price

1975-01-01

A strong structural exterior flakeboard from mixed southern hardwoods has been developed on a laboratory scale; the problem is transfer of the technique to pilot-plant scale in the manufacture of 4- by 8-ft panels. From the pilot-plant trial here reported, it is concluded that a specific platen pressure of at least 575 psi and a hot press closing time of about 45...

Development and operation of innovative scum to biodiesel pilot-system for the treatment of floatable wastewater scum.

PubMed

Anderson, Erik; Addy, Min; Chen, Paul; Ruan, Roger

2018-02-01

A novel process was developed for the biorefining of floatable wastewater scum and other waste oils from water treatment facilities into biodiesel and other value-added bio-products. To test the scalability and commercial potential of the technology, a 7000 l/year pilot-scale system was designed and built. Scum from a wastewater treatment facility, located in St. Paul, Mn, was collected and converted into methyl esters (biodiesel) according to the process chemistry. All of the incoming and outgoing process streams were sampled, tested, weighed and recorded to calculate both the process efficiency and product quality. Data from the pilot-scale system operation was compared to laboratory results and the theoretically expected values for each individual unit operation. The biodiesel was tested using a third party laboratory and confirmed it met all of the US EPA's test requirements for commercial-grade biodiesel. Copyright © 2017 Elsevier Ltd. All rights reserved.

Physical-chemical treatment of rainwater runoff in recovery and recycling companies: Pilot-scale optimization.

PubMed

Blondeel, Evelyne; Depuydt, Veerle; Cornelis, Jasper; Chys, Michael; Verliefde, Arne; Van Hulle, Stijin Wim Henk

2015-01-01

Pilot-scale optimisation of different possible physical-chemical water treatment techniques was performed on the wastewater originating from three different recovery and recycling companies in order to select a (combination of) technique(s) for further full-scale implementation. This implementation is necessary to reduce the concentration of both common pollutants (such as COD, nutrients and suspended solids) and potentially toxic metals, polyaromatic hydrocarbons and poly-chlorinated biphenyls frequently below the discharge limits. The pilot-scale tests (at 250 L h(-1) scale) demonstrate that sand anthracite filtration or coagulation/flocculation are interesting as first treatment techniques with removal efficiencies of about 19% to 66% (sand anthracite filtration), respectively 18% to 60% (coagulation/flocculation) for the above mentioned pollutants (metals, polyaromatic hydrocarbons and poly chlorinated biphenyls). If a second treatment step is required, the implementation of an activated carbon filter is recommended (about 46% to 86% additional removal is obtained).

Integration of visual and motion cues for simulator requirements and ride quality investigation. [computerized simulation of aircraft landing, visual perception of aircraft pilots

NASA Technical Reports Server (NTRS)

Young, L. R.

1975-01-01

Preliminary tests and evaluation are presented of pilot performance during landing (flight paths) using computer generated images (video tapes). Psychophysiological factors affecting pilot visual perception were measured. A turning flight maneuver (pitch and roll) was specifically studied using a training device, and the scaling laws involved were determined. Also presented are medical studies (abstracts) on human response to gravity variations without visual cues, acceleration stimuli effects on the semicircular canals, and neurons affecting eye movements, and vestibular tests.

Development of a pilot-scale kinetic extruder feeder system and test program. Phase II. Verification testing. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-01-12

This report describes the work done under Phase II, the verification testing of the Kinetic Extruder. The main objective of the test program was to determine failure modes and wear rates. Only minor auxiliary equipment malfunctions were encountered. Wear rates indicate useful life expectancy of from 1 to 5 years for wear-exposed components. Recommendations are made for adapting the equipment for pilot plant and commercial applications. 3 references, 20 figures, 12 tables.

Amyris, Inc. Integrated Biorefinery Project Summary Final Report - Public Version

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gray, David; Sato, Suzanne; Garcia, Fernando

The Amyris pilot-scale Integrated Biorefinery (IBR) leveraged Amyris synthetic biology and process technology experience to upgrade Amyris’s existing Emeryville, California pilot plant and fermentation labs to enable development of US-based production capabilities for renewable diesel fuel and alternative chemical products. These products were derived semi-synthetically from high-impact biomass feedstocks via microbial fermentation to the 15-carbon intermediate farnesene, with subsequent chemical finishing to farnesane. The Amyris IBR team tested and provided methods for production of diesel and alternative chemical products from sweet sorghum, and other high-impact lignocellulosic feedstocks, at pilot scale. This enabled robust techno-economic analysis (TEA), regulatory approvals, and amore » basis for full-scale manufacturing processes and facility design.« less

Texas Urban Triangle : pilot study to implement a spatial decision support system (SDSS) for sustainable mobility.

DOT National Transportation Integrated Search

2011-03-01

This project addressed sustainable transportation in the Texas Urban Triangle (TUT) by conducting a pilot : project at the county scale. The project tested and developed the multi-attribute Spatial Decision Support : System (SDSS) developed in 2009 u...

Preliminary Engineering Report for the Use of Peracetic Acid at the Oak Ridge National Laboratory Sewage Treatment Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, Paul Allen

2017-02-01

The purpose of this report is to identify other disinfection methods to replace the current ozone system and propose a small pilot-scale test. Based on a review of the literature and disinfectants used by other wastewater plants in Tennessee, peracetic acid (PAA) was identified as a leading candidate. This report provides the basis for requesting approval for a pilot-scale study using PAA.

Pilot Testing a Cognitive-Behavioral Protocol on Psychosocial Predictors of Exercise, Nutrition, Weight, and Body Satisfaction Changes in a College-Level Health-Related Fitness Course

ERIC Educational Resources Information Center

Annesi, James J.; Howton, Amy; Johnson, Ping H.; Porter, Kandice J.

2015-01-01

Objective: Small-scale pilot testing of supplementing a required college health-related fitness course with a cognitive-behavioral exercise-support protocol (The Coach Approach). Participants: Three classes were randomly assigned to Usual processes (n = 32), Coach Approach-supplemented: Mid-size Groups (n = 32), and Coach Approach-supplemented:…

[Development of an activity of daily living scale for patients with COPD: the Activity of Daily Living Dyspnea scale].

PubMed

Yoza, Yoshiyasu; Ariyoshi, Koya; Honda, Sumihisa; Taniguchi, Hiroyuki; Senjyu, Hideaki

2009-10-01

Patients with COPD often experience restriction in their activities of daily living (ADL) due to dyspnea. This type of restriction is unique to patients with COPD and cannot be adequately evaluated by the generic ADL scales. This study developed an ADL scale (the Activity of Daily Living Dyspnea scale [ADL-D scale]) for patients with COPD and investigated its validity and internal consistency. Patients with stable COPD were recruited and completed a pilot 26-item questionnaire. Patients also performed the Incremental Shuttle Walk Test (ISWT), and completed the St George's Respiratory Questionnaire (SGRQ), and Medical Research Council (MRC) dyspnea grade. There were 83 male participants who completed the pilot questionnaire. Following the pilot, 8 items that were not undertaken by the majority of subjects, and 3 items judged to be of low clinical importance by physical therapists were removed from the pilot questionnaire. The final ADL-D scale contained 15 items. Scores obtained with the ADL-D scale were significantly correlated with the MRC dyspnea grades, distance walked on the ISWT and SGRQ scores. The ADL-D scores were significantly different across the five grades of the MRC dyspnea grade. The ADL-D scale showed high consistency (Chronbach's alpha coefficient of 0.96). The ADL-D scale is a useful scale for assessing impairments in ADL in Japanese male patients with COPD.

Free-Spinning-Tunnel Tests of a 0.057-Scale Model of the Chance Vought XF7U-1 Airplane

NASA Technical Reports Server (NTRS)

Daughtridge, Lee T., Jr.

1948-01-01

An investigation of the spin and recovery characteristics of a 0.057-scale model of the Chance Vought XF7U-1 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect and inverted spin and recovery characteristics were determined, as were also the effects of extending the wing slats, of center-of-gravity movement, and-of variation in the mass distribution. The investigation also included wing-tip spin-recovery-parachute tests, pilot-escape tests, and rudder-control-force tests. The investigation indicated that the spin and recovery characteristics of the airplane will be satisfactory for all conditions. It was found that a single 4.24-foot (full-scale) parachute when opened alone from the outboard wing tip or two 8.77-foot (full-scale) parachutes when opened simultaneously, one from each wing tip, would effect satisfactory emergency recoveries (the drag coefficients of the parachutes, based on the surface area of the parachute, were 0.83 and 0.70 for the 4.24- and 8.77-foot parachutes, respectively). The towline length in both cases was 25 feet (full scale). Tests results showed that, if the pilot should have to leave the airplane during a spin, he should jump from the outboard side (left side in a right spin) of the cockpit. The rudder-control force necessary for recovery from a spin was found to be rather high but appeared to be within the upper limits of a pilot's capabilities.

An Approach to Scoring and Equating Tests with Binary Items: Piloting With Large-Scale Assessments

ERIC Educational Resources Information Center

Dimitrov, Dimiter M.

2016-01-01

This article describes an approach to test scoring, referred to as "delta scoring" (D-scoring), for tests with dichotomously scored items. The D-scoring uses information from item response theory (IRT) calibration to facilitate computations and interpretations in the context of large-scale assessments. The D-score is computed from the…

Methodological approaches to conducting pilot and proof tests on reverse-osmosis systems: Results of comparative studies

NASA Astrophysics Data System (ADS)

Panteleev, A. A.; Bobinkin, V. V.; Larionov, S. Yu.; Ryabchikov, B. E.; Smirnov, V. B.; Shapovalov, D. A.

2017-10-01

When designing large-scale water-treatment plants based on reverse-osmosis systems, it is proposed to conduct experimental-industrial or pilot tests for validated simulation of the operation of the equipment. It is shown that such tests allow establishing efficient operating conditions and characteristics of the plant under design. It is proposed to conduct pilot tests of the reverse-osmosis systems on pilot membrane plants (PMPs) and test membrane plants (TMPs). The results of a comparative experimental study of pilot and test membrane plants are exemplified by simulating the operating parameters of the membrane elements of an industrial plant. It is concluded that the reliability of the data obtained on the TMP may not be sufficient to design industrial water-treatment plants, while the PMPs are capable of providing reliable data that can be used for full-scale simulation of the operation of industrial reverse-osmosis systems. The test membrane plants allow simulation of the operating conditions of individual industrial plant systems; therefore, potential areas of their application are shown. A method for numerical calculation and experimental determination of the true selectivity and the salt passage are proposed. An expression has been derived that describes the functional dependence between the observed and true salt passage. The results of the experiments conducted on a test membrane plant to determine the true value of the salt passage of a reverse-osmosis membrane are exemplified by magnesium sulfate solution at different initial operating parameters. It is shown that the initial content of a particular solution component has a significant effect on the change in the true salt passage of the membrane.

Low Activity Waste Pretreatment System Bench-Scale Testing: Supporting Integrated Testing and Facility Safety Analyses - 17171

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schonewill, Philip P.; Russell, Renee L.; Daniel, Richard C.

The Low Activity Waste Pretreatment System (LAWPS) is being designed to enable the direct feed of waste to the Hanford Tank Waste Treatment and Immobilization Plant (WTP) Low Activity Waste (LAW) facility to be immobilized. Prior to construction of the LAWPS, pilot-scale integrated testing of the key unit operations (crossflow filtration, ion exchange using spherical resorcinol-formaldehyde (sRF) resin) will be conducted by a team led by Washington River Protection Solutions (WRPS) to increase the technology maturation level of the facility’s critical technology elements. As a part of this effort, Pacific Northwest National Laboratory (PNNL) has conducted a series of bench-scalemore » (or engineering-scale) tests to perform two major objectives: (1) support pilot-scale integrated testing of the LAWPS by supplying information or performance data in advance of operating the pilot-scale facility; and (2) collect data needed to establish or confirm assumptions/approaches planned for implementation in the LAWPS safety basis. The first objective was focused in two technical areas: developing simulants that are representative of expected waste feed and can be produced at larger scales, and using these simulants in a bench-scale crossflow filter to establish expected solid-liquid separation performance. The crossflow filter was also used to observe the efficacy (with respect to filter production rate) of selected operational strategies. The second objective also included two technical areas: measuring the effect of sRF resin on hydrogen generation rate under irradiation, and demonstrating that the planned hydrogen management approach is effective and robust. The hydrogen management strategy involves fluidization of the sRF resin bed in the ion exchange columns and recirculating the liquid, a scenario that is planned for testing at full column height. The full height tests at PNNL also supported full-scale IX column testing conducted as part of the technology maturation plan. The experimental approaches used at PNNL in these four technical areas are summarized and selected key preliminary results are provided.« less

Pilot-scale ISCO treatment of a MtBE contaminated site using a Fenton-like process.

PubMed

Innocenti, Ivan; Verginelli, Iason; Massetti, Felicia; Piscitelli, Daniela; Gavasci, Renato; Baciocchi, Renato

2014-07-01

This paper reports about a pilot-scale feasibility study of In-Situ Chemical Oxidation (ISCO) application based on the use of stabilized hydrogen peroxide catalyzed by naturally occurring iron minerals (Fenton-like process) to a site formerly used for fuel storage and contaminated by MtBE. The stratigraphy of the site consists of a 2-3 meter backfill layer followed by a 3-4 meter low permeability layer, that confines the main aquifer, affected by a widespread MtBE groundwater contamination with concentrations up to 4000 μg/L, also with the presence of petroleum hydrocarbons. The design of the pilot-scale treatment was based on the integration of the results obtained from experimental and numerical modeling accounting for the technological and regulatory constraints existing in the site to be remediated. In particular, lab-scale batch tests allowed the selection of the most suitable operating conditions. Then, this information was implemented in a numerical software that allowed to define the injection and monitoring layout and to predict the propagation of hydrogen peroxide in groundwater. The pilot-scale field results confirmed the effective propagation of hydrogen peroxide in nearly all the target area (around 75 m(2) using 3 injection wells). As far as the MtBE removal is concerned, the ISCO application allowed us to meet the clean-up goals in an area of 60 m(2). Besides, the concentration of TBA, i.e. a potential by-product of MtBE oxidation, was actually reduced after the ISCO treatment. The results of the pilot-scale test suggest that ISCO may be a suitable option for the remediation of the groundwater plume contaminated by MtBE, providing the background data for the design and cost-estimate of the full-scale treatment. Copyright © 2014 Elsevier B.V. All rights reserved.

[Diagnostic test scale SI5: Assessment of sacroiliac joint dysfunction].

PubMed

Acevedo González, Juan C; Quintero Oliveros, Silvia

2015-01-01

Sacroiliac joint dysfunction is a known cause of low back pain. We think that a diagnostic score scale (SI5) may be performed to assess diagnostic utility of clinical signs of sacroiliac joint dysfunction. The primary aim of the present study was to conduct the pilot study of our new diagnostic score scale, the SI5, for sacroiliac joint syndrome. We reviewed the literature on clinical characteristics, diagnostic tests and imaging most commonly used in diagnosing sacroiliac joint dysfunction. Our group evaluated the diagnostic utility of these aspects and we used those considered most representative to develop the SI5 diagnostic scale. The SI5 scale was applied to 22 patients with low back pain; afterwards, the standard test for diagnosing this pathology (selective blockage of the SI joint) was also performed on these patients. The sensitivity and specificity for each sign were also assessed and the diagnostic scale called SI5 was then proposed, based on these data. The most sensitive clinical tests for diagnosing SI joint dysfunction were 2 patient-reported clinical characteristics, the Laguerre Test, sacroiliac rocking test and Yeomans test (greater than 80% sensitivity). The tests with greatest diagnostic specificity (>80%) were the Lewitt test, Piedallu test and Gillet test. The proposed SI5 test score scale showed sensitivity of 73% and specificity of 71%. Sacroiliac joint syndrome has been shown to produce low back pain frequently; however, the diagnostic value of examination tests for sacroiliac joint pain has been questioned by other authors. The pilot study on the SI5 diagnostic score scale showed good sensitivity and specificity. However, the process of statistical validation of the SI5 needs to be continued. Copyright © 2014 Sociedad Española de Neurocirugía. Published by Elsevier España. All rights reserved.

Performance of a system with full- and pilot-scale sludge drying reed bed units treating septic tank sludge in Brazil.

PubMed

Calderón-Vallejo, Luisa Fernanda; Andrade, Cynthia Franco; Manjate, Elias Sete; Madera-Parra, Carlos Arturo; von Sperling, Marcos

2015-01-01

This study investigated the performance of sludge drying reed beds (SDRB) at full- and pilot-scale treating sludge from septic tanks in the city of Belo Horizonte, Brazil. The treatment units, planted with Cynodon spp., were based on an adaptation of the first-stage of the French vertical-flow constructed wetland, originally developed for treating sewage. Two different operational phases were investigated; in the first one, the full-scale unit was used together with six pilot-scale columns in order to test different feeding strategies. For the second phase, only the full-scale unit was used, including a recirculation of the filtered effluent (percolate) to one of the units of the French vertical wetland. Sludge application was done once a week emptying a full truck, during 25 weeks. The sludge was predominantly diluted, leading to low solids loading rates (median values of 18 kgTS m(-2) year(-1)). Chemical oxygen demand removal efficiency in the full-scale unit was reasonable (median of 71%), but the total solids removal was only moderate (median of 44%) in the full-scale unit without recirculation. Recirculation did not bring substantial improvements in the overall performance. The other loading conditions implemented in the pilot columns also did not show statistically different performances.

Hydrothermal and alkaline hydrothermal pretreatments plus anaerobic digestion of sewage sludge for dewatering and biogas production: Bench-scale research and pilot-scale verification.

PubMed

Li, Chunxing; Wang, Xingdong; Zhang, Guangyi; Yu, Guangwei; Lin, Jingjiang; Wang, Yin

2017-06-15

To test the feasibility and practicability of the process combing hydrothermal pretreatment for dewatering with biogas production for full utilization of sewage sludge, hydrothermal/alkaline hydrothermal pretreatments and in turn anaerobic digestion of the filtrates obtained after dewatering the pretreated sludge were performed at bench- and pilot-scales. The hydrothermal temperature fell within the range of 140 °C-220 °C and the pretreatment time varied from 30 min to 120 min. For the alkaline hydrothermal pretreatment the pH value of the sludge was adjusted to 9.0-11.0 by adding Ca(OH) 2 . The results showed that the dewaterability of the sewage sludge was improved with increasing pretreatment temperature but the impact of the pretreatment time was not significant. The addition of Ca(OH) 2 gave better performance on the subsequent mechanical dewatering of the pretreated sludge compared to pure hydrothermal pretreatment, and the higher the pH value was, the better the dewaterability of the pretreated sludge was. The conditions of 180 °C/30 min and 160 °C/60 min/pH = 10.0 (for hydrothermal and alkaline hydrothermal pretreatments, respectively) resulted in relatively good results in the theoretical energy balance, which were verified in the pilot-scale tests. Based on the data from the pilot tests, the alkaline hydrothermal process realized self-sufficiency in energy at the cost of a proper amount of CaO. Copyright © 2017 Elsevier Ltd. All rights reserved.

PREVENTION OF ELEMENTAL MERCURY REEMISSIONS FROM ILLINOIS COAL WET SCRUBBERS

EPA Science Inventory

This research conducted pilot plant tests to investigate techniques for controlling and reducing Hg⁰ re-emissions. A pilot-scale (0.01MW) wet scrubber was designed to simulate the wet limestone flue gas desulfurization system. Hg⁰ re-emissions, manifested by...

Design and fabrication of a fixed-bed batch type pyrolysis reactor for pilot scale pyrolytic oil production in Bangladesh

NASA Astrophysics Data System (ADS)

Aziz, Mohammad Abdul; Al-khulaidi, Rami Ali; Rashid, MM; Islam, M. R.; Rashid, MAN

2017-03-01

In this research, a development and performance test of a fixed-bed batch type pyrolysis reactor for pilot scale pyrolysis oil production was successfully completed. The characteristics of the pyrolysis oil were compared to other experimental results. A solid horizontal condenser, a burner for furnace heating and a reactor shield were designed. Due to the pilot scale pyrolytic oil production encountered numerous problems during the plant’s operation. This fixed-bed batch type pyrolysis reactor method will demonstrate the energy saving concept of solid waste tire by creating energy stability. From this experiment, product yields (wt. %) for liquid or pyrolytic oil were 49%, char 38.3 % and pyrolytic gas 12.7% with an operation running time of 185 minutes.

New mechanistically based model for predicting reduction of biosolids waste by ozonation of return activated sludge.

PubMed

Isazadeh, Siavash; Feng, Min; Urbina Rivas, Luis Enrique; Frigon, Dominic

2014-04-15

Two pilot-scale activated sludge reactors were operated for 98 days to provide the necessary data to develop and validate a new mathematical model predicting the reduction of biosolids production by ozonation of the return activated sludge (RAS). Three ozone doses were tested during the study. In addition to the pilot-scale study, laboratory-scale experiments were conducted with mixed liquor suspended solids and with pure cultures to parameterize the biomass inactivation process during exposure to ozone. The experiments revealed that biomass inactivation occurred even at the lowest doses, but that it was not associated with extensive COD solubilization. For validation, the model was used to simulate the temporal dynamics of the pilot-scale operational data. Increasing the description accuracy of the inactivation process improved the precision of the model in predicting the operational data. Copyright © 2014 Elsevier B.V. All rights reserved.

Validation and cross-cultural pilot testing of compliance with standard precautions scale: self-administered instrument for clinical nurses.

PubMed

Lam, Simon C

2014-05-01

To perform detailed psychometric testing of the compliance with standard precautions scale (CSPS) in measuring compliance with standard precautions of clinical nurses and to conduct cross-cultural pilot testing and assess the relevance of the CSPS on an international platform. A cross-sectional and correlational design with repeated measures. Nursing students from a local registered nurse training university, nurses from different hospitals in Hong Kong, and experts in an international conference. The psychometric properties of the CSPS were evaluated via internal consistency, 2-week and 3-month test-retest reliability, concurrent validation, and construct validation. The cross-cultural pilot testing and relevance check was examined by experts on infection control from various developed and developing regions. Among 453 participants, 193 were nursing students, 165 were enrolled nurses, and 95 were registered nurses. The results showed that the CSPS had satisfactory reliability (Cronbach α = 0.73; intraclass correlation coefficient, 0.79 for 2-week test-retest and 0.74 for 3-month test-retest) and validity (optimum correlation with criterion measure; r = 0.76, P < .001; satisfactory results on known-group method and hypothesis testing). A total of 19 experts from 16 countries assured that most of the CSPS findings were relevant and globally applicable. The CSPS demonstrated satisfactory results on the basis of the standard international criteria on psychometric testing, which ascertained the reliability and validity of this instrument in measuring the compliance of clinical nurses with standard precautions. The cross-cultural pilot testing further reinforced the instrument's relevance and applicability in most developed and developing regions.

Instrument Development of Integrative Health and Wellness Assessment™.

PubMed

McElligott, Deborah; Eckardt, Sarah; Montgomery Dossey, Barbara; Luck, Susan; Eckardt, Patricia

2017-12-01

The nurse coach role was developed to address the needs of our nation and the world for health and wellbeing. The Theory of Integrative Nurse Coaching provides a foundation for coaching interventions supporting health promotion, and a framework for the development of the Integrative Health and Wellness Assessment (IHWA) short form. This 36-question Likert-type scale self-reporting tool assists participants in assessing healthy behaviors through a self-reflection process, provides information for the coaching relationship, and may be an outcome measurement. This article describes the history of the IHWA tool and the development and pilot testing of the IHWA short form using guidelines provided by DeVellis. Results of the Kaiser-Meyer-Olkin test yielded a value of .520, and the Bartlett's test of sphericity was significant. Cronbach's alpha overall scale internal consistency was .88 ( n = 36). Pilot study results indicate that the scale could be improved through additional revision, and an ongoing study is in progress.

Investigation and demonstration of dry carbon-based sorbent injection for mercury control. Quarterly technical report, July 1, 1996--September 31, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunt, T.; Sjostrom, S.; Smith, J.

1996-11-06

The overall objective of this two phase program is to investigate the use of dry carbon-based sorbents for mercury control. This information is important to the utility industry in anticipation of pending regulations. During Phase I, a bench-scale field test device that can be configured as an electrostatic precipitator, a pulse-jet baghouse, or a reverse-gas baghouse has been designed, built and integrated with an existing pilot-scale facility at PSCo`s Comanche Station. Up to three candidate sorbents will be injected into the flue gas stream upstream of the test device to and mercury concentration measurements will be made to determine themore » mercury removal efficiency for each sorbent. During the Phase II effort, component integration for the most promising dry sorbent technology shall be tested at the 5000 acfm pilot-scale.« less

Ultra scale-down device to predict dewatering levels of solids recovered in a continuous scroll decanter centrifuge.

PubMed

Lopes, A G; Keshavarz-Moore, E

2013-01-01

During centrifugation operation, the major challenge in the recovery of extracellular proteins is the removal of the maximum liquid entrapped within the spaces between the settled solids-dewatering level. The ability of the scroll decanter centrifuge (SDC) to process continuously large amounts of feed material with high concentration of solids without the need for resuspension of feeds, and also to achieve relatively high dewatering, could be of great benefit for future use in the biopharmaceutical industry. However, for reliable prediction of dewatering in such a centrifuge, tests using the same kind of equipment at pilot-scale are required, which are time consuming and costly. To alleviate the need of pilot-scale trials, a novel USD device, with reduced amounts of feed (2 mL) and to be used in the laboratory, was developed to predict the dewatering levels of a SDC. To verify USD device, dewatering levels achieved were plotted against equivalent compression (Gtcomp ) and decanting (Gtdec ) times, obtained from scroll rates and feed flow rates operated at pilot-scale, respectively. The USD device was able to successfully match dewatering trends of the pilot-scale as a function of both Gtcomp and Gtdec , particularly for high cell density feeds, hence accounting for all key variables that influenced dewatering in a SDC. In addition, it accurately mimicked the maximum dewatering performance of the pilot-scale equipment. Therefore the USD device has the potential to be a useful tool at early stages of process development to gather performance data in the laboratory thus minimizing lengthy and costly runs with pilot-scale SDC. © 2013 American Institute of Chemical Engineers.

Full-scale results for TAM limestone injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baer, S.

1996-12-31

Information is outlined on the use of thermally active marble (TAM) sorbents in boilers. Data are presented on: the comparison of TAM to limestone; NOVACON process development history; CFB test history; CFB pilot scale test; full-scale CFB trial; August, 1996 CFB demonstration; Foster Wheeler Mount Carmel sorbent feed rate comparison and Ca:S comparison; unburned carbon is ash; and advantages and savings in CFB boilers.

SITE EMERGING TECHNOLOGY SUMMARY: INTEGRATION OF PHOTOCATALYTIC OXIDATION WITH AIR STRIPPING OF CONTAMINATED AQUIFERS

EPA Science Inventory

In a recently completed test program, bench-scale laboratory studies at Arizona State University (ASU) in Tempe, AZ, and pilot-scale studies in a simulated field test situation at Zentox Corp in Ocala, FL, were performed to evaluate the integration of gas-solid ultraviolet (UV) p...

OPERATIONS AND RESEARCH AT THE U.S. EPA INCINERATION RESEARCH FACILITY: ANNUAL REPORT FOR FY94

EPA Science Inventory

Fiscal year 1994 (FY94, October 1, 1993 through September 30,1994) saw the continuation of incineration research testing efforts at the IRF. uring the year, two major pilot-scale programs were completed and a third carried to near-completion, and two bench-scale test programs of ...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Windisch, C.F. Jr.; Strachan, D.M.; Henager, C.H. Jr.

Cermet anodes were evaluated as nonconsumable substitutes for carbon anodes using a pilot-scale reduction cell at the Reynolds Manufacturing Technology Laboratory. After pilot cell testing, tile anodes were subjected to extensive materials characterization and physical properties measurements at the Pacific Northwest Laboratory. Significant changes in the composition of the cermet anodes were observed including the growth of a reaction layer and penetration of electrolyte deep into the cermet matrix. Fracture strength and toughness were measured as a function of temperature and the ductile-brittle transition wasreduced by 500C following pilot cell testing. These results imply difficulties with anode material and controlmore » of operating conditions in the pilot cell, and suggest that additional development work be performed before the cermet anodes are used in commercial reduction cells. The results also highlight specific fabrication and operational considerations that should be addressed in future testing.« less

Engineering evaluation of magma cooling-tower demonstration at Nevada Power Company's Sunrise Station

NASA Astrophysics Data System (ADS)

1980-11-01

The Magma Cooling Tower (MCT) process utilizes a falling film heat exchanger integrated into an induced draft cooling tower to evaporate waste water. A hot water source such as return cooling water provides the energy for evaporation. Water quality control is maintained by removing potential scaling constituents to make concentrations of the waste water possible without scaling heat transfer surfaces. A pilot-scale demonstration test of the MCT process was performed from March 1979 through June 1979 at Nevada Power Company's Sunrise Station in Las Vegas, Nevada. The pilot unit extracted heat from the powerplant cooling system to evaporate cooling tower blowdown. Two water quality control methods were employed: makeup/sidestream softening and fluidized bed crystallization. The 11 week softening mode test was successful.

Determining the Influence of Groundwater Composition on the Performance of Arsenic Adsorption Columns Using Rapid Small-Scale Column Tests

NASA Astrophysics Data System (ADS)

Aragon, A. R.; Siegel, M.

2004-12-01

The USEPA has established a more stringent drinking water standard for arsenic, reducing the maximum contaminant level (MCL) from 50 μ g/L to 10 μ g/L. This will affect many small communities in the US that lack the appropriate treatment infrastructure and funding to reduce arsenic to such levels. For such communities, adsorption systems are the preferred technology based on ease of operation and relatively lower costs. The performance of adsorption media for the removal of arsenic from drinking water is dependent on site-specific water quality. At certain concentrations, co-occurring solutes will compete effectively with arsenic for sorption sites, potentially reducing the sorption capacity of the media. Due to the site-specific nature of water quality and variations in media properties, pilot scale studies are typically carried out to ensure that a proposed treatment technique is cost effective before installation of a full-scale system. Sandia National Laboratories is currently developing an approach to utilize rapid small-scale columns in lieu of pilot columns to test innovative technologies that could significantly reduce the cost of treatment in small communities. Rapid small-scale column tests (RSSCTs) were developed to predict full-scale treatment of organic contaminants by adsorption onto granular activated carbon (GAC). This process greatly reduced the time and costs required to verify performance of GAC adsorption columns. In this study, the RSSCT methodology is used to predict the removal of inorganic arsenic using mixed metal oxyhydroxide adsorption media. The media are engineered and synthesized from materials that control arsenic behavior in natural and disturbed systems. We describe the underlying theory and application of RSSCTs for the performance evaluation of novel media in several groundwater compositions. Results of small-scale laboratory columns are being used to predict the performance of pilot-scale systems and ultimately to design full-scale systems. RSSCTs will be performed on a suite of water compositions representing the variety of water supplies in the United States that are affected by the new drinking water standard. Ultimately, this approach will be used to carry out inexpensive short-term pilot studies at a large number of sites where large-scale pilots are not economically feasible. Sandia National Laboratories is a multi-program laboratory operated by Sandia Corporation, a Lockheed Martin company, for the United States Department of Energy's National Nuclear Security Administration under Contract DE-AC04-94AL85000.

easyCBM CCSS Math Item Scaling and Test Form Revision (2012-2013): Grades 6-8. Technical Report #1313

ERIC Educational Resources Information Center

Anderson, Daniel; Alonzo, Julie; Tindal, Gerald

2012-01-01

The purpose of this technical report is to document the piloting and scaling of new easyCBM mathematics test items aligned with the Common Core State Standards (CCSS) and to describe the process used to revise and supplement the 2012 research version easyCBM CCSS math tests in Grades 6-8. For all operational 2012 research version test forms (10…

Development of a Drug Use Resistance Self-Efficacy (DURSE) Scale

ERIC Educational Resources Information Center

Carpenter, Carrie M.; Howard, Donna

2009-01-01

Objectives: To develop and evaluate psychometric properties of a new instrument, the drug use resistance self-efficacy (DURSE) scale, designed for young adolescents. Methods: Scale construction occurred in 3 phases: (1) initial development, (2) pilot testing of preliminary items, and (3) final scale administration among a sample of seventh graders…

Pilot-scale production of fuel ethanol from concentrated food waste hydrolysates using Saccharomyces cerevisiae H058.

PubMed

Yan, Shoubao; Chen, Xiangsong; Wu, Jingyong; Wang, Pingchao

2013-07-01

The aim of this study was to develop a bioprocess to produce ethanol from food waste at laboratory, semipilot and pilot scales. Laboratory tests demonstrated that ethanol fermentation with reducing sugar concentration of 200 g/L, inoculum size of 2 % (Initial cell number was 2 × 10⁶ CFU/mL) and addition of YEP (3 g/L of yeast extract and 5 g/L of peptone) was the best choice. The maximum ethanol concentration in laboratory scale (93.86 ± 1.15 g/L) was in satisfactory with semipilot scale (93.79 ± 1.11 g/L), but lower than that (96.46 ± 1.12 g/L) of pilot-scale. Similar ethanol yield and volumetric ethanol productivity of 0.47 ± 0.02 g/g, 1.56 ± 0.03 g/L/h and 0.47 ± 0.03 g/g, 1.56 ± 0.03 g/L/h after 60 h of fermentation in laboratory and semipilot fermentors, respectively, however, both were lower than that (0.48 ± 0.02 g/g, 1.79 ± 0.03 g/L/h) of pilot reactor. In addition, simple models were developed to predict the fermentation kinetics during the scale-up process and they were successfully applied to simulate experimental results.

[Design and validation of scales to measure adolescent attitude toward eating and toward physical activity].

PubMed

Lima-Serrano, Marta; Lima-Rodríguez, Joaquín Salvador; Sáez-Bueno, Africa

2012-01-01

Different authors suggest that attitude is a mediator in behavior change, so it is a predictor of behavior practice. The main of this study was to design and to validate two scales for measure adolescent attitude toward healthy eating and adolescent attitude toward healthy physical activity. Scales were design based on a literature review. After, they were validated using an on-line Delphi Panel with eighteen experts, a pretest, and a pilot test with a sample of 188 high school students. Comprehensibility, content validity, adequacy, as well as the reliability (alpha of Cronbach test), and construct validity (exploratory factor analysis) of scales were tested. Scales validated by experts were considered appropriate in the pretest. In the pilot test, the ten-item Attitude to Eating Scale obtained α=0.72. The eight-item Attitude to Physical Activity Scale obtained α=0.86. They showed evidence of one-dimensional interpretation after factor analysis, a) all items got weights r>0.30 in first factor before rotations, b) the first factor explained a significant proportion of variance before rotations, and c) the total variance explained by the main factors extracted was greater than 50%. The Scales showed their reliability and validity. They could be employed to assess attitude to these priority intervention areas in Spanish adolescents, and to evaluate this intermediate result of health interventions and health programs.

Advanced gasifier and water gas shift technologies for low cost coal conversion to high hydrogen syngas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kramer, Andrew Kramer

The Gas Technology Institute (GTI) and team members RTI International (RTI), Coanda Research and Development, and Nexant, are developing and maturing a portfolio of technologies to meet the United States Department of Energy (DOE) goals for lowering the cost of producing high hydrogen syngas from coal for use in carbon capture power and coal-to-liquids/chemicals. This project matured an advanced pilot-scale gasifier, with scalable and commercially traceable components, to readiness for use in a first-of-a-kind commercially-relevant demonstration plant on the scale of 500-1,000 tons per day (TPD). This was accomplished through cold flow simulation of the gasifier quench zone transition regionmore » at Coanda and through an extensive hotfire gasifier test program on highly reactive coal and high ash/high ash fusion temperature coals at GTI. RTI matured an advanced water gas shift process and catalyst to readiness for testing at pilot plant scale through catalyst development and testing, and development of a preliminary design basis for a pilot scale reactor demonstrating the catalyst. A techno-economic analysis was performed by Nexant to assess the potential benefits of the gasifier and catalyst technologies in the context of power production and methanol production. This analysis showed an 18%reduction in cost of power and a 19%reduction in cost of methanol relative to DOE reference baseline cases.« less

Development process of an assessment tool for disruptive behavior problems in cross-cultural settings: the Disruptive Behavior International Scale – Nepal version (DBIS-N)

PubMed Central

Burkey, Matthew D.; Ghimire, Lajina; Adhikari, Ramesh P.; Kohrt, Brandon A.; Jordans, Mark J. D.; Haroz, Emily; Wissow, Lawrence

2017-01-01

Systematic processes are needed to develop valid measurement instruments for disruptive behavior disorders (DBDs) in cross-cultural settings. We employed a four-step process in Nepal to identify and select items for a culturally valid assessment instrument: 1) We extracted items from validated scales and local free-list interviews. 2) Parents, teachers, and peers (n=30) rated the perceived relevance and importance of behavior problems. 3) Highly rated items were piloted with children (n=60) in Nepal. 4) We evaluated internal consistency of the final scale. We identified 49 symptoms from 11 scales, and 39 behavior problems from free-list interviews (n=72). After dropping items for low ratings of relevance and severity and for poor item-test correlation, low frequency, and/or poor acceptability in pilot testing, 16 items remained for the Disruptive Behavior International Scale—Nepali version (DBIS-N). The final scale had good internal consistency (α=0.86). A 4-step systematic approach to scale development including local participation yielded an internally consistent scale that included culturally relevant behavior problems. PMID:28093575

A dual-task home-based rehabilitation programme for improving balance control in patients with acquired brain injury: a single-blind, randomized controlled pilot study.

PubMed

Peirone, Eliana; Goria, Paolo Filiberto; Anselmino, Arianna

2014-04-01

To evaluate the safety, feasibility and effectiveness of a dual-task home-based rehabilitation programme on balance impairments among adult patients with acquired brain injury. Single-blind, randomized controlled pilot study. Single rehabilitation centre. Sixteen participants between 12 and 18 months post-acquired brain injury with balance impairments and a score <10 seconds on the One-Leg Stance Test (eyes open). All participants received 50-minutes individualised traditional physiotherapy sessions three times a week for seven weeks. In addition, the intervention group (N = 8) performed an individualised dual-task home-based programme six days a week for seven weeks. The primary outcome measure was the Balance Evaluation System Test; secondary measures were the Activities-specific Balance Confidence Scale and Goal Attainment Scaling. At the end of the pilot study, the intervention group showed significantly greater improvement in Balance Evaluation System Test scores (17.87, SD 6.05) vs. the control group (5.5, SD 3.53; P = 0.008, r = 0.63). There was no significant difference in improvement in Activities-specific Balance Confidence Scale scores between the intervention group (25.25, SD 25.51) and the control group (7.00, SD 14.73; P = 0.11, r = 0.63). There was no significant improvement in Goal Attainment Scaling scores in the intervention (19.37, SD 9.03) vs. the control group (16.28, SD 6.58; P = 0.093, r = 0.63). This pilot study shows the safety, feasibility and short-term benefit of a dual-task home-based rehabilitation programme to improve balance control in patients with acquired brain injury. A sample size of 26 participants is required for a definitive study.

Optimization of the inter-tablet coating uniformity for an active coating process at lab and pilot scale.

PubMed

Just, Sarah; Toschkoff, Gregor; Funke, Adrian; Djuric, Dejan; Scharrer, Georg; Khinast, Johannes; Knop, Klaus; Kleinebudde, Peter

2013-11-30

The objective of this study was to enhance the inter-tablet coating uniformity in an active coating process at lab and pilot scale by statistical design of experiments. The API candesartan cilexetil was applied onto gastrointestinal therapeutic systems containing the API nifedipine to obtain fixed dose combinations of these two drugs with different release profiles. At lab scale, the parameters pan load, pan speed, spray rate and number of spray nozzles were examined. At pilot scale, the parameters pan load, pan speed, spray rate, spray time, and spray pressure were investigated. A low spray rate and a high pan speed improved the coating uniformity at both scales. The number of spray nozzles was identified as the most influential variable at lab scale. With four spray nozzles, the highest CV value was equal to 6.4%, compared to 13.4% obtained with two spray nozzles. The lowest CV of 4.5% obtained with two spray nozzles was further reduced to 2.3% when using four spray nozzles. At pilot scale, CV values between 2.7% and 11.1% were achieved. Since the test of uniformity of dosage units accepts CV values of up to 6.25%, this active coating process is well suited to comply with the pharmacopoeial requirements. Copyright © 2013 Elsevier B.V. All rights reserved.

An Integrated Approach to Assess Broad-Scale Condition of Coastal Wetlands – The Gulf of Mexico Coastal Wetlands Pilot Survey.

EPA Science Inventory

The Environmental Protection Agency (EPA) and U.S. Geological Survey (USGS) initiated a two-year regional pilot survey in 2007 to develop, test, and validate tools and approaches to assess the condition of northern Gulf of Mexico (GOM) coastal wetlands. Sampling sites were select...

Pilot testing of a membrane system for postcombustion CO 2 capture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merkel, Tim; Kniep, Jay; Wei, Xiaotong

2015-09-30

This final report summarizes work conducted for the U.S. Department of Energy, National Energy Technology Laboratory (DOE) to scale up an efficient post-combustion CO 2 capture membrane process to the small pilot test stage (award number DE-FE0005795). The primary goal of this research program was to design, fabricate, and operate a membrane CO 2 capture system to treat coal-derived flue gas containing 20 tonnes CO 2/day (20 TPD). Membrane Technology and Research (MTR) conducted this project in collaboration with Babcock and Wilcox (B&W), the Electric Power Research Institute (EPRI), WorleyParsons (WP), the Illinois Sustainable Technology Center (ISTC), Enerkem (EK), andmore » the National Carbon Capture Center (NCCC). In addition to the small pilot design, build and slipstream testing at NCCC, other project efforts included laboratory membrane and module development at MTR, validation field testing on a 1 TPD membrane system at NCCC, boiler modeling and testing at B&W, a techno-economic analysis (TEA) by EPRI/WP, a case study of the membrane technology applied to a ~20 MWe power plant by ISTC, and an industrial CO 2 capture test at an Enerkem waste-to-biofuel facility. The 20 TPD small pilot membrane system built in this project successfully completed over 1,000 hours of operation treating flue gas at NCCC. The Polaris™ membranes used on this system demonstrated stable performance, and when combined with over 10,000 hours of operation at NCCC on a 1 TPD system, the risk associated with uncertainty in the durability of postcombustion capture membranes has been greatly reduced. Moreover, next-generation Polaris membranes with higher performance and lower cost were validation tested on the 1 TPD system. The 20 TPD system also demonstrated successful operation of a new low-pressure-drop sweep module that will reduce parasitic energy losses at full scale by as much as 10 MWe. In modeling and pilot boiler testing, B&W confirmed the viability of CO 2 recycle to the boiler as envisioned in the MTR process design. The impact of this CO 2 recycle on boiler efficiency was quantified and incorporated into a TEA of the membrane capture process applied to a full-scale power plant. As with previous studies, the TEA showed the membrane process to be lower cost than the conventional solvent capture process even at 90% CO 2capture. A sensitivity study indicates that the membrane capture cost decreases significantly if the 90% capture requirement is relaxed. Depending on the process design, a minimum capture cost is achieved at 30-60% capture, values that would meet proposed CO 2 emission regulations for coal-fired power plants. In summary, this project has successfully advanced the MTR membrane capture process through small pilot testing (technology readiness level 6). The technology is ready for future scale-up to the 10 MWe size.« less

Farm-scale testing of soybean peroxidase and calcium peroxide for surficial swine manure treatment and mitigation of odorous VOCs, ammonia and hydrogen sulfide

USDA-ARS?s Scientific Manuscript database

The swine industry, regulatory agencies, and the public are interested in farm-tested methods for controlling gaseous emissions from swine barns. In earlier lab- and pilot-scale studies, a renewable catalyst consisting of soybean peroxidase (SBP) mixed with calcium peroxide was found to be effective...

Evaluation of pilot-scale pulse-corona-induced plasma device to remove NO{sub x} from combustion exhausts from a subscale combustor and from a hush house at Nellis AFB, Nevada. Final report, August 1994--January 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haythornthwaite, S.M.; Durham, M.D.; Anderson, G.L.

1997-05-01

Jet engine test cells (JETCs) are used to test-fire new, installed, and reworked jet engines. Because JETCs have been classified as stationary sources of pollutant emissions, they are subject to possible regulation under Title 1 of the Clean Air Act (CAA) as amended in 1990. In Phase 1 of the Small Business Innovation Research (SBIR) program, a novel NOx-control approach utilizing pulsed-corona-induced plasma successfully showed 90% removal of NOx in the laboratory. The objective of Phase 2 was to reproduce the laboratory-scale results in a pilot-scale system. The technology was successfully demonstrated at pilot scale in the field, on amore » slipstream of JETC flue gas at Nellis Air Force Base. Based on the field data, cost projections were made for a system to treat the full JETC exhaust. The technology efficiently converted NO into ONO, and a wet scrubber was required to achieve the treatment goal of 50-percent removal and destruction of NOx. The plasma simultaneously removes hydrocarbons from the flue gas stream. This project demonstrated that pulse-corona-induced plasma technology is scalable to practical industrial dimensions.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menon, R.; Grames, L.M.

Pilot Carrousel testing was conducted for about three months on wastewaters generated at a major potato processing facility in 1993. The testing focused toward removal of BOD, NH{sub 3} and NO{sub 3}, and Total-P. After five-six weeks that it took for the system to reach steady state operation, the pilot plant was able to treat the wastewaters quite well. Effluent BOD{sub 5} and TKN values were less than 8 and 4 mg/L, respectively, during the second half of testing. Total-P in the effluent was less than 10 mg/L, although this step was not optimized. Based on the pilot testing, amore » full-scale Carrousel activated sludge plant was designed and commissioned in 1994. This plant is currently treating all the wastewaters from the facility and performing contaminant removals at a very high level.« less

Discrimination of surface wear on obsidian tools using LSCM and RelA: pilot study results (area-scale analysis of obsidian tool surfaces).

PubMed

Stemp, W James; Chung, Steven

2011-01-01

This pilot study tests the reliability of laser scanning confocal microscopy (LSCM) to quantitatively measure wear on experimental obsidian tools. To our knowledge, this is the first use of confocal microscopy to study wear on stone flakes made from an amorphous silicate like obsidian. Three-dimensional surface roughness or texture area scans on three obsidian flakes used on different contact materials (hide, shell, wood) were documented using the LSCM to determine whether the worn surfaces could be discriminated using area-scale analysis, specifically relative area (RelA). When coupled with the F-test, this scale-sensitive fractal analysis could not only discriminate the used from unused surfaces on individual tools, but was also capable of discriminating the wear histories of tools used on different contact materials. Results indicate that such discriminations occur at different scales. Confidence levels for the discriminations at different scales were established using the F-test (mean square ratios or MSRs). In instances where discrimination of surface roughness or texture was not possible above the established confidence level based on MSRs, photomicrographs and RelA assisted in hypothesizing why this was so. Copyright © 2011 Wiley Periodicals, Inc.

Effects of scapulohumeral rehabilitation protocol on trunk control recovery in patients with subacute stroke: A pilot randomized controlled trial.

PubMed

Dell'Uomo, Daniela; Morone, Giovanni; Centrella, Antonio; Paolucci, Stefano; Caltagirone, Carlo; Grasso, Maria Grazia; Traballesi, Marco; Iosa, Marco

2017-01-01

Despite upper limb rehabilitation is widely investigated in patients with stroke, the effects of scapulohumeral rehabilitation on trunk stabillization are mainly unknown. To test the effects of scapulohumeral rehabilitation protocol on trunk control recovery in patients with subacute stroke. A pilot randomized controlled trial with two groups of 14 patients each one performing 20 minutes per day, 5 days a week, for 6 weeks in add on to standard therapy. Experimental group performed a specific scapulohumeral rehabilitation protocol aiming to improve trunk competencies whereas control group performed conventional arm rehabilitation. Clinical scale tests and accelerometric evaluations were performed pre- and post-treatment. Experimental groups showed better scores at discharge at Trunk impairment Scale (p < 0.001), Barthel Index (p = 0.024), Trunk Control Test (p = 0.002), Sitting Balance Scale (p = 0.002), but neither at Fugl-Meyer Scale (p = 0.194) nor Modified Ashworth Scale (p = 0.114). Accelerometric analysis showed higher stability of trunk for experimental group especially during static and dynamic items. The recovery of scapulohumeral functions also acts on trunk stabilization post-stroke.

Application of Titration-Based Screening for the Rapid Pilot Testing of High-Throughput Assays.

PubMed

Zhang, Ji-Hu; Kang, Zhao B; Ardayfio, Ophelia; Ho, Pei-i; Smith, Thomas; Wallace, Iain; Bowes, Scott; Hill, W Adam; Auld, Douglas S

2014-06-01

Pilot testing of an assay intended for high-throughput screening (HTS) with small compound sets is a necessary but often time-consuming step in the validation of an assay protocol. When the initial testing concentration is less than optimal, this can involve iterative testing at different concentrations to further evaluate the pilot outcome, which can be even more time-consuming. Quantitative HTS (qHTS) enables flexible and rapid collection of assay performance statistics, hits at different concentrations, and concentration-response curves in a single experiment. Here we describe the qHTS process for pilot testing in which eight-point concentration-response curves are produced using an interplate asymmetric dilution protocol in which the first four concentrations are used to represent the range of typical HTS screening concentrations and the last four concentrations are added for robust curve fitting to determine potency/efficacy values. We also describe how these data can be analyzed to predict the frequency of false-positives, false-negatives, hit rates, and confirmation rates for the HTS process as a function of screening concentration. By taking into account the compound pharmacology, this pilot-testing paradigm enables rapid assessment of the assay performance and choosing the optimal concentration for the large-scale HTS in one experiment. © 2013 Society for Laboratory Automation and Screening.

Characterization of reactive CaCO 3 crystallization in a fluidized bed reactor as a central process of direct air capture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burhenne, Luisa; Giacomin, Caroline; Follett, Trevor

A laboratory-scale, fluidized-bed pellet reactor (BPR) was used to investigate a CaCO 3 crystallization process for the recovery of CO 2 in a Direct Air Capture (DAC) process. The BPR performance was validated against data from a pilot-scale unit. Subsequently, the pellet growth under process-relevant conditions was studied over a period of 144 h. The experimental results with the BPR, containing a bed of pellets sized between 0.65 and 0.84 mm, have shown that a calcium retention of 80% can be achieved at a fluidization velocity of 60 m h -1 and a calcium loading rate of 3 mol hmore » -1. This result is consistent with calcium retention observed at pilot scale operation and hence, results from the BPR are considered representative for the pilot scale unit. Starting with a bed of pellets sized between 0.15 and 0.5 mm, the average pellet growth rate, G, at the reactor bottom increased from 8.1E-10 to 11E–10 m s -1 at the onset and decreased to 4.9E–10 m s -1 over the course of a 144 h test. The calcium retention over the course the test showed the same trend (initial increase and final decrease) as the pellet growth rate. A theoretical bed growth model was developed and validated against data from the pilot scale and benchtop pellet reactors. The model was used to calculate the bed porosity and total pellet surface area in each control volume. Lastly, the pellet surface area growth at the bottom of the reactor reproduced the pellet growth and retention data trends.« less

Characterization of reactive CaCO 3 crystallization in a fluidized bed reactor as a central process of direct air capture

DOE PAGES

Burhenne, Luisa; Giacomin, Caroline; Follett, Trevor; ...

2017-10-25

A laboratory-scale, fluidized-bed pellet reactor (BPR) was used to investigate a CaCO 3 crystallization process for the recovery of CO 2 in a Direct Air Capture (DAC) process. The BPR performance was validated against data from a pilot-scale unit. Subsequently, the pellet growth under process-relevant conditions was studied over a period of 144 h. The experimental results with the BPR, containing a bed of pellets sized between 0.65 and 0.84 mm, have shown that a calcium retention of 80% can be achieved at a fluidization velocity of 60 m h -1 and a calcium loading rate of 3 mol hmore » -1. This result is consistent with calcium retention observed at pilot scale operation and hence, results from the BPR are considered representative for the pilot scale unit. Starting with a bed of pellets sized between 0.15 and 0.5 mm, the average pellet growth rate, G, at the reactor bottom increased from 8.1E-10 to 11E–10 m s -1 at the onset and decreased to 4.9E–10 m s -1 over the course of a 144 h test. The calcium retention over the course the test showed the same trend (initial increase and final decrease) as the pellet growth rate. A theoretical bed growth model was developed and validated against data from the pilot scale and benchtop pellet reactors. The model was used to calculate the bed porosity and total pellet surface area in each control volume. Lastly, the pellet surface area growth at the bottom of the reactor reproduced the pellet growth and retention data trends.« less

Major- and Trace-Element Concentrations in Soils from Northern California: Results from the Geochemical Landscapes Project Pilot Study

USGS Publications Warehouse

Morrison, Jean M.; Goldhaber, Martin B.; Holloway, JoAnn M.; Smith, David B.

2008-01-01

In 2004, the U.S. Geological Survey (USGS), the Geological Survey of Canada (GSC), and the Mexican Geological Survey (Servicio Geologico Mexicano, or SGM) initiated pilot studies in preparation for a soil geochemical survey of North America called the Geochemical Landscapes Project. The purpose of this project is to provide a better understanding of the variability in chemical composition of soils in North America. The data produced by this survey will be used to construct baseline geochemical maps for regions within the continent. Two initial pilot studies were conducted: (1) a continental-scale study involving a north-south and east-west transect across North America and (2) a regional-scale study. The pilot studies were intended to test and refine sample design, sampling protocols, and field logistics for the full continental soils geochemical survey. Smith and others (2005) reported the results from the continental-scale pilot study. The regional-scale California study was designed to represent more detailed, higher resolution geochemical investigations in a region of particular interest that was identified from the low-sample-density continental-scale survey. A 20,000-km2 area of northern California (fig. 1), representing a wide variety of topography, climate, and ecoregions, was chosen for the regional-scale pilot study. This study area also contains diverse geology and soil types and supports a wide range of land uses including agriculture in the Sacramento Valley, forested areas in portions of the Sierra Nevada, and urban/suburban centers such as Sacramento, Davis, and Stockton. Also of interest are potential effects on soil geochemistry from historical hard rock and placer gold mining in the foothills of the Sierra Nevada, historical mercury mining in the Coast Range, and mining of base-metal sulfide deposits in the Klamath Mountains to the north. This report presents the major- and trace-element concentrations from the regional-scale soil geochemical survey in northern California.

Comparison of batch sorption tests, pilot studies, and modeling for estimating GAC bed life.

PubMed

Scharf, Roger G; Johnston, Robert W; Semmens, Michael J; Hozalski, Raymond M

2010-02-01

Saint Paul Regional Water Services (SPRWS) in Saint Paul, MN experiences annual taste and odor episodes during the warm summer months. These episodes are attributed primarily to geosmin that is produced by cyanobacteria growing in the chain of lakes used to convey and store the source water pumped from the Mississippi River. Batch experiments, pilot-scale experiments, and model simulations were performed to determine the geosmin removal performance and bed life of a granular activated carbon (GAC) filter-sorber. Using batch adsorption isotherm parameters, the estimated bed life for the GAC filter-sorber ranged from 920 to 1241 days when challenged with a constant concentration of 100 ng/L of geosmin. The estimated bed life obtained using the AdDesignS model and the actual pilot-plant loading history was 594 days. Based on the pilot-scale GAC column data, the actual bed life (>714 days) was much longer than the simulated values because bed life was extended by biological degradation of geosmin. The continuous feeding of high concentrations of geosmin (100-400 ng/L) in the pilot-scale experiments enriched for a robust geosmin-degrading culture that was sustained when the geosmin feed was turned off for 40 days. It is unclear, however, whether a geosmin-degrading culture can be established in a full-scale filter that experiences taste and odor episodes for only 1 or 2 months per year. The results of this research indicate that care must be exercised in the design and interpretation of pilot-scale experiments and model simulations for predicting taste and odor removal in full-scale GAC filter-sorbers. Adsorption and the potential for biological degradation must be considered to estimate GAC bed life for the conditions of intermittent geosmin loading typically experienced by full-scale systems. (c) 2009 Elsevier Ltd. All rights reserved.

Advanced, Energy-Efficient Hybrid Membrane System for Industrial Water Reuse

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toy, Lora; Choi, Young Chul; Hendren, Zachary

In the U.S. manufacturing sector, current industrial water use practices are energy-intensive and utilize and discharge high volumes of waters, rendering them not sustainable especially in light of the growing scarcity of suitable water supplies. To help address this problem, the goal of this project was to develop an advanced, cost-effective, hybrid membrane-based water treatment system that can improve the energy efficiency of industrial wastewater treatment while allowing at least 50% water reuse efficiency. This hybrid process would combine emerging Forward Osmosis (FO) and Membrane Distillation (MD) technology components into an integrated FO-MD system that can beneficially utilize low-grade wastemore » heat (i.e., T < 450 °F) in industrial facilities to produce distilled-quality product water for reuse. In this project, laboratory-, bench-, and pilot-scale experiments on the hybrid FO-MD system were conducted for industrial wastewater treatment. It was demonstrated at laboratory, bench, and pilot scales that FO-MD membrane technology can concentrate brine to very high total dissolved solids (TDS) levels (>200,000 ppm) that are at least 2.5 times higher than the TDS level to which RO can achieve. In laboratory testing, currently available FO and MD membranes were tested to select for high-performing membranes with high salt rejection and high water flux. Multiple FO membrane/draw-salt solution combinations that gave high water flux with higher than 98% salt rejection were also identified. Reverse draw-salt fluxes were observed to be much lower for divalent salts than for monovalent salts. MD membranes were identified that had 99.9+% salt rejection and water flux as high as 50-90 L/(m 2·h) for flat-sheet membranes and >20 L/(m 2·h) for hollow fibers. In bench-scale testing, a single unit of commercially available FO and MD membrane modules were evaluated for continuous, integrated operation. Using the laboratory- and bench-scale test data, numerical modeling was performed on the FO and MD processes to estimate engineering parameters for a larger-scale pilot unit. Based on the experimental studies and modeling results, a pilot-scale, integrated FO-MD prototype unit was designed and built for trailer-mounted operation. This prototype system was fed real industrial wastewater, which could not be further treated by conventional technologies, from an oil production facility and was successfully operated for over 15 weeks without major stoppage. About 90% water recovery was possible, while concentrating the TDS from 12,000 ppm up to 190,500 ppm. The FO-MD prototype rejected most wastewater contaminants while producing water with <300 ppm TDS, even when the feed TDS was higher than 150,000 ppm. No chemical cleaning was necessary during the pilot testing period. Flushing the system with dechlorinated tap water was sufficient to reset the membranes for the next set of test conditions. Pilot performance and membrane autopsy showed that, even though the feed was concentrated more than 10 times, membrane fouling was unnoticeable and no defects were detected on the FO and MD membrane surfaces. This project demonstrated the technical feasibility of the hybrid FO-MD process by taking water already treated to the limit with the highest level of current technologies and further concentrating it 10-fold by using mostly low-cost materials. Because no membranes suitable for full-scale plant applications are available at present, economical feasibility of the hybrid technology is still uncertain, but it is expected that broader industry participation can further reduce FO-MD process costs.« less

Laboratory and pilot-scale bioremediation of pentaerythritol tetranitrate (PETN) contaminated soil.

PubMed

Zhuang, Li; Gui, Lai; Gillham, Robert W; Landis, Richard C

2014-01-15

PETN (pentaerythritol tetranitrate), a munitions constituent, is commonly encountered in munitions-contaminated soils, and pose a serious threat to aquatic organisms. This study investigated anaerobic remediation of PETN-contaminated soil at a site near Denver Colorado. Both granular iron and organic carbon amendments were used in both laboratory and pilot-scale tests. The laboratory results showed that, with various organic carbon amendments, PETN at initial concentrations of between 4500 and 5000mg/kg was effectively removed within 84 days. In the field trial, after a test period of 446 days, PETN mass removal of up to 53,071mg/kg of PETN (80%) was achieved with an organic carbon amendment (DARAMEND) of 4% by weight. In previous laboratory studies, granular iron has shown to be highly effective in degrading PETN. However, for both the laboratory and pilot-scale tests, granular iron was proven to be ineffective. This was a consequence of passivation of the iron surfaces caused by the very high concentrations of nitrate in the contaminated soil. This study indicated that low concentration of organic carbon was a key factor limiting bioremediation of PETN in the contaminated soil. Furthermore, the addition of organic carbon amendments such as the DARAMEND materials or brewers grain, proved to be highly effective in stimulating the biodegradation of PETN and could provide the basis for full-scale remediation of PETN-contaminated sites. Copyright © 2013 Elsevier B.V. All rights reserved.

Age, gender, neck circumference, and Epworth sleepiness scale do not predict obstructive sleep apnea (OSA) in moderate to severe chronic obstructive pulmonary disease (COPD): The challenge to predict OSA in advanced COPD.

PubMed

Soler, Xavier; Liao, Shu-Yi; Marin, Jose Maria; Lorenzi-Filho, Geraldo; Jen, Rachel; DeYoung, Pamela; Owens, Robert L; Ries, Andrew L; Malhotra, Atul

2017-01-01

The combination of chronic obstructive pulmonary disease (COPD) and obstructive sleep apnea (OSA) is associated with substantial morbidity and mortality. We hypothesized that predictors of OSA among patients with COPD may be distinct from OSA in the general population. Therefore, we investigated associations between traditional OSA risk factors (e.g. age), and sleep questionnaires [e.g. Epworth Sleepiness Scale] in 44 patients with advanced COPD. As a second aim we proposed a pilot, simplified screening test for OSA in patients with COPD. In a prospective, observational study of patients enrolled in the UCSD Pulmonary Rehabilitation Program we collected baseline characteristics, cardiovascular events (e.g. atrial fibrillation), and sleep questionnaires [e.g. Pittsburgh Sleep Quality Index (PSQI)]. For the pilot questionnaire, a BMI ≥25 kg/m2 and the presence of cardiovascular disease were used to construct the pilot screening test. Male: 59%; OSA 66%. FEV1 (mean ± SD) = 41.0±18.2% pred., FEV1/FVC = 41.5±12.7%]. Male gender, older age, and large neck circumference were not associated with OSA. Also, Epworth Sleepiness Scale and the STOP-Bang questionnaire were not associated with OSA in univariate logistic regression. In contrast, BMI ≥25 kg/m2 (OR = 3.94, p = 0.04) and diagnosis of cardiovascular disease (OR = 5.06, p = 0.03) were significantly associated with OSA [area under curve (AUC) = 0.74]. The pilot COPD-OSA test (OR = 5.28, p = 0.05) and STOP-Bang questionnaire (OR = 5.13, p = 0.03) were both associated with OSA in Receiver Operating Characteristics (ROC) analysis. The COPD-OSA test had the best AUC (0.74), sensitivity (92%), and specificity (83%). A ten-fold cross-validation validated our results. We found that traditional OSA predictors (e.g. gender, Epworth score) did not perform well in patients with more advanced COPD. Our pilot test may be an easy to implement instrument to screen for OSA. However, a larger validation study is necessary before further clinical implementation is warranted.

Age, gender, neck circumference, and Epworth sleepiness scale do not predict obstructive sleep apnea (OSA) in moderate to severe chronic obstructive pulmonary disease (COPD): The challenge to predict OSA in advanced COPD

PubMed Central

Marin, Jose Maria; Lorenzi-Filho, Geraldo; Jen, Rachel; DeYoung, Pamela; Owens, Robert L.; Ries, Andrew L.; Malhotra, Atul

2017-01-01

The combination of chronic obstructive pulmonary disease (COPD) and obstructive sleep apnea (OSA) is associated with substantial morbidity and mortality. We hypothesized that predictors of OSA among patients with COPD may be distinct from OSA in the general population. Therefore, we investigated associations between traditional OSA risk factors (e.g. age), and sleep questionnaires [e.g. Epworth Sleepiness Scale] in 44 patients with advanced COPD. As a second aim we proposed a pilot, simplified screening test for OSA in patients with COPD. In a prospective, observational study of patients enrolled in the UCSD Pulmonary Rehabilitation Program we collected baseline characteristics, cardiovascular events (e.g. atrial fibrillation), and sleep questionnaires [e.g. Pittsburgh Sleep Quality Index (PSQI)]. For the pilot questionnaire, a BMI ≥25 kg/m2 and the presence of cardiovascular disease were used to construct the pilot screening test. Male: 59%; OSA 66%. FEV1 (mean ± SD) = 41.0±18.2% pred., FEV1/FVC = 41.5±12.7%]. Male gender, older age, and large neck circumference were not associated with OSA. Also, Epworth Sleepiness Scale and the STOP-Bang questionnaire were not associated with OSA in univariate logistic regression. In contrast, BMI ≥25 kg/m2 (OR = 3.94, p = 0.04) and diagnosis of cardiovascular disease (OR = 5.06, p = 0.03) were significantly associated with OSA [area under curve (AUC) = 0.74]. The pilot COPD-OSA test (OR = 5.28, p = 0.05) and STOP-Bang questionnaire (OR = 5.13, p = 0.03) were both associated with OSA in Receiver Operating Characteristics (ROC) analysis. The COPD-OSA test had the best AUC (0.74), sensitivity (92%), and specificity (83%). A ten-fold cross-validation validated our results. We found that traditional OSA predictors (e.g. gender, Epworth score) did not perform well in patients with more advanced COPD. Our pilot test may be an easy to implement instrument to screen for OSA. However, a larger validation study is necessary before further clinical implementation is warranted. PMID:28510598

Market assessment of PFBC ash use

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bland, A. E.; Brown, T. H., Western Research Institute

1998-01-01

Pressurized fluidized bed combustion (PFBC) of coal is undergoing demonstration in the United States, as well as throughout the world. American Electric Power`s (AEP`s) bubbling PFBC 70 MWe Tidd demonstration program in Ohio and pilot-scale development at Foster Wheeler Energia Oy 10 MWth circulating PFBC at Karhula, Finland, have demonstrated the advantages of PFBC technology. Further technology development in the US is planned with the deployment of the technology at the MacIntosh Clean Coal project in Lakeland, Florida. Development of uses for solid wastes from PFBC coal-fired power systems is being actively pursued as part of the demonstration of PFBCmore » technologies. Ashes collected from Foster Wheeler Energia Oy pilot circulating PFBC tests in Karhula, Finland, operating on (1) low sulfur subbituminous and (2) high sulfur bituminous coal; and ash from the AEP`s high-sulfur bituminous coal-fired bubbling PFBC in Brilliant, Ohio, were evaluated in laboratory and pilot-scale ash use testing at Western Research Institute (WRI).« less

In-Flight Validation of a Pilot Rating Scale for Evaluating Failure Transients in Electronic Flight Control Systems

NASA Technical Reports Server (NTRS)

Kalinowski, Kevin F.; Tucker, George E.; Moralez, Ernesto, III

2006-01-01

Engineering development and qualification of a Research Flight Control System (RFCS) for the Rotorcraft Aircrew Systems Concepts Airborne Laboratory (RASCAL) JUH-60A has motivated the development of a pilot rating scale for evaluating failure transients in fly-by-wire flight control systems. The RASCAL RFCS includes a highly-reliable, dual-channel Servo Control Unit (SCU) to command and monitor the performance of the fly-by-wire actuators and protect against the effects of erroneous commands from the flexible, but single-thread Flight Control Computer. During the design phase of the RFCS, two piloted simulations were conducted on the Ames Research Center Vertical Motion Simulator (VMS) to help define the required performance characteristics of the safety monitoring algorithms in the SCU. Simulated failures, including hard-over and slow-over commands, were injected into the command path, and the aircraft response and safety monitor performance were evaluated. A subjective Failure/Recovery Rating (F/RR) scale was developed as a means of quantifying the effects of the injected failures on the aircraft state and the degree of pilot effort required to safely recover the aircraft. A brief evaluation of the rating scale was also conducted on the Army/NASA CH-47B variable stability helicopter to confirm that the rating scale was likely to be equally applicable to in-flight evaluations. Following the initial research flight qualification of the RFCS in 2002, a flight test effort was begun to validate the performance of the safety monitors and to validate their design for the safe conduct of research flight testing. Simulated failures were injected into the SCU, and the F/RR scale was applied to assess the results. The results validate the performance of the monitors, and indicate that the Failure/Recovery Rating scale is a very useful tool for evaluating failure transients in fly-by-wire flight control systems.

Leaching assessment of road materials containing primary lead and zinc slags.

PubMed

Barna, R; Moszkowicz, P; Gervais, C

2004-01-01

Characterisation of the leaching behaviour of waste-containing materials is a crucial step in the environmental assessment for reuse scenarios. In our research we applied the multi-step European methodology ENV 12-920 to the leaching assessment of road materials containing metallurgical slag. A Zn slag from an imperial smelting furnace (ISF) and a Pb slag from a lead blast furnace (LBF) are investigated. The two slags contain up to 11.2 wt% of lead and 3.5 wt% of zinc and were introduced as a partial substitute for sand in two road materials, namely sand-cement and sand-bitumen. At the laboratory scale, a leaching assessment was performed first through batch equilibrium leaching tests. Second, the release rate of the contaminants was evaluated using saturated leaching tests on monolithic material. Third, laboratory tests were conducted on monolithic samples under intermittent wetting conditions. Pilot-scale tests were conducted for field testing of intermittent wetting conditions. The results show that the release of Pb and Zn from the materials in a saturated scenario was controlled by the pH of the leachates. For the intermittent wetting conditions, an additional factor, blocking of the pores by precipitation during the drying phase is proposed. Pilot-scale leaching behaviour only partially matched with the laboratory-scale test results: new mass transfer mechanisms and adapted laboratory leaching tests are discussed.

INTEGRATION OF PHOTOCATALYTIC OXIDATION WITH AIR STRIPPING OF CONTAMINATED AQUIFERS

EPA Science Inventory

Bench scale laboratory studies and pilot scale studies in a simulated field-test situation were performed to evaluate the integration of gas-solid ultaviolet (UV) photocatalytic oxidation (PCO) downstream if an air stripper unit as a technology for cost-effectively treating water...

Experimental Study on Hot Metal Desulfurization Using Sintered Red Mud-Based Flux

NASA Astrophysics Data System (ADS)

Li, Fengshan; Zhang, Yanling; Guo, Zhancheng

2017-09-01

This research presents the results of laboratory and pilot-scale tests conducted on the use of sintered red mud (RM)-based flux in the hot metal desulfurization (HMD) process. Al2O3/Na2O in RM can decrease the melting point of lime-based slag and can work as a flux in the HMD process. Good slag fluidity was observed throughout the process, and high desulfurization rates ( 80%) with a low final S content (<0.02%) were experimentally obtained when the RM:CaO ratio was between 1.2:1 and 2.4:1. The pilot-scale test results indicated that a desulfurization rate as high as 91% and a S content <0.0099% could be acquired when RM:lime = 1:1, verifying the feasibility of using sintered RM-based flux in HMD. The data obtained provide important information for promoting the large-scale application of sintered RM in steelmaking.

Development of a remote digital augmentation system and application to a remotely piloted research vehicle

NASA Technical Reports Server (NTRS)

Edwards, J. W.; Deets, D. A.

1975-01-01

A cost-effective approach to flight testing advanced control concepts with remotely piloted vehicles is described. The approach utilizes a ground based digital computer coupled to the remotely piloted vehicle's motion sensors and control surface actuators through telemetry links to provide high bandwidth feedback control. The system was applied to the control of an unmanned 3/8-scale model of the F-15 airplane. The model was remotely augmented; that is, the F-15 mechanical and control augmentation flight control systems were simulated by the ground-based computer, rather than being in the vehicle itself. The results of flight tests of the model at high angles of attack are discussed.

Careers of Professional Staff in Australian and UK Universities: A Mixed Methods Pilot Study

ERIC Educational Resources Information Center

Gander, Michelle

2017-01-01

This article confirms the reliability of a protean and boundaryless career attitudes scale, tested in a pilot study. Additionally, it summarises the results of this study into the career attitudes of professional staff in Australian and UK universities. A mixed methods approach was taken using a survey consisting of both closed questions on a…

Design and testing of a pilot scale magnetic separator for the treatment of textile dyeing wastewater.

PubMed

Salinas, Tobías; Durruty, Ignacio; Arciniegas, Lorena; Pasquevich, Gustavo; Lanfranconi, Matías; Orsi, Isabela; Alvarez, Vera; Bonanni, Sebastian

2018-07-15

Iron nanoparticles can be incorporated on the structure of natural clays to obtain magnetic clays, an adsorbent that be easily removed from a wastewater by magnetic means. Magnetic clays have high adsorption capacities of different contaminants such as heavy metals, fungicides, aromatic compounds and colorants and show rapid adsorption kinetics, but crucial data for achieving its full or pilot scale application is still lacking. In this work, magnetic bentonites with different amounts of magnetite (iron fractions on the clay of 0.55, 0.6 and 0.6) were used to remove color from a real textile wastewater. On a first stage the optimal conditions for the adsorption of the dye, including pH, temperature and clay dosage were determined. Also design parameters for the separation process such as residence time, distance from magnet to magnetic clay and magnet strength were obtained. Finally a pilot scale magnetic drum separator was constructed and tested. A removal of 60% of the dye from a wastewater that contained more than 250 ppm of azo dye was achieved with only 10 min of residence time inside the separator. Copyright © 2018 Elsevier Ltd. All rights reserved.

A 200kW central receiver CPV system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lasich, John, E-mail: jbl@raygen.com; Thomas, Ian, E-mail: ithomas@raygen.com; Hertaeg, Wolfgang

2015-09-28

Raygen Resources has recently completed a Central Receiver CPV (CSPV) pilot plant in Central Victoria, Australia. The system is under final commissioning and initial operation is expected in late April 2015. The pilot demonstrates a full scale CSPV repeatable unit in a form that is representative of a commercial product and provides a test bed to prove out performance and reliability of the CSPV technology. Extensive testing of the system key components: dense array module, wireless solar powered heliostat and control system has been performed in the laboratory and on sun. Results from this key component testing are presented herein.

Hydrometallurgical recovery of germanium from coal gasification fly ash: pilot plant scale evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arroyo, F.; Fernandez-Pereira, C.; Olivares, J.

2009-04-15

In this article, a hydrometallurgical method for the selective recovery of germanium from fly ash (FA) has been tested at pilot plant scale. The pilot plant flowsheet comprised a first stage of water leaching of FA, and a subsequent selective recovery of the germanium from the leachate by solvent extraction method. The solvent extraction method was based on Ge complexation with catechol in an aqueous solution followed by the extraction of the Ge-catechol complex (Ge(C{sub 6}H{sub 4}O{sub 2}){sub 3}{sup 2-}) with an extracting organic reagent (trioctylamine) diluted in an organic solvent (kerosene), followed by the subsequent stripping of the organicmore » extract. The process has been tested on a FA generated in an integrated gasification with combined cycle (IGCC) process. The paper describes the designed 5 kg/h pilot plant and the tests performed on it. Under the operational conditions tested, approximately 50% of germanium could be recovered from FA after a water extraction at room temperature. Regarding the solvent extraction method, the best operational conditions for obtaining a concentrated germanium-bearing solution practically free of impurities were as follows: extraction time equal to 20 min; aqueous phase/organic phase volumetric ratio equal to 5; stripping with 1 M NaOH, stripping time equal to 30 min, and stripping phase/organic phase volumetric ratio equal to 5. 95% of germanium were recovered from water leachates using those conditions.« less

PILOT SCALE WATER REUSE SYSTEM

EPA Science Inventory

The efficiency of the treatment technologies is expected to vary with the source water quality. By testing the technologies with various source waters, the research will quantify the limits of the technology: testing the flow rate variations with influent water quality, evalu...

The Postoperative Pain Assessment Skills pilot trial.

PubMed

McGillion, Michael; Dubrowski, Adam; Stremler, Robyn; Watt-Watson, Judy; Campbell, Fiona; McCartney, Colin; Victor, Charles; Wiseman, Jeffrey; Snell, Linda; Costello, Judy; Robb, Anja; Nelson, Sioban; Stinson, Jennifer; Hunter, Judith; Dao, Thuan; Promislow, Sara; McNaughton, Nancy; White, Scott; Shobbrook, Cindy; Jeffs, Lianne; Mauch, Kianda; Leegaard, Marit; Beattie, W Scott; Schreiber, Martin; Silver, Ivan

2011-01-01

BACKGROUND⁄ Pain-related misbeliefs among health care professionals (HCPs) are common and contribute to ineffective postoperative pain assessment. While standardized patients (SPs) have been effectively used to improve HCPs' assessment skills, not all centres have SP programs. The present equivalence randomized controlled pilot trial examined the efficacy of an alternative simulation method - deteriorating patient-based simulation (DPS) - versus SPs for improving HCPs' pain knowledge and assessment skills. Seventy-two HCPs were randomly assigned to a 3 h SP or DPS simulation intervention. Measures were recorded at baseline, immediate postintervention and two months postintervention. The primary outcome was HCPs' pain assessment performance as measured by the postoperative Pain Assessment Skills Tool (PAST). Secondary outcomes included HCPs knowledge of pain-related misbeliefs, and perceived satisfaction and quality of the simulation. These outcomes were measured by the Pain Beliefs Scale (PBS), the Satisfaction with Simulated Learning Scale (SSLS) and the Simulation Design Scale (SDS), respectively. Student's t tests were used to test for overall group differences in postintervention PAST, SSLS and SDS scores. One-way analysis of covariance tested for overall group differences in PBS scores. DPS and SP groups did not differ on post-test PAST, SSLS or SDS scores. Knowledge of pain-related misbeliefs was also similar between groups. These pilot data suggest that DPS is an effective simulation alternative for HCPs' education on postoperative pain assessment, with improvements in performance and knowledge comparable with SP-based simulation. An equivalence trial to examine the effectiveness of deteriorating patient-based simulation versus standardized patients is warranted.

FULL-SCALE TESTS OF THE MULTI-CHAMBERED TREATMENT TANK (MCTT)

EPA Science Inventory

The MCTT was developed to control toxicants in stormwater from critical source areas. During monitoring, the pilot-scale MCTT provided median reductions of >90% for toxicity, lead, zinc, and most organic toxicants. Suspended solids was reduced by 83% and COD was reduced by 60%. T...

The Child-care Food and Activity Practices Questionnaire (CFAPQ): development and first validation steps.

PubMed

Gubbels, Jessica S; Sleddens, Ester Fc; Raaijmakers, Lieke Ch; Gies, Judith M; Kremers, Stef Pj

2016-08-01

To develop and validate a questionnaire to measure food-related and activity-related practices of child-care staff, based on existing, validated parenting practices questionnaires. A selection of items from the Comprehensive Feeding Practices Questionnaire (CFPQ) and the Preschooler Physical Activity Parenting Practices (PPAPP) questionnaire was made to include items most suitable for the child-care setting. The converted questionnaire was pre-tested among child-care staff during cognitive interviews and pilot-tested among a larger sample of child-care staff. Factor analyses with Varimax rotation and internal consistencies were used to examine the scales. Spearman correlations, t tests and ANOVA were used to examine associations between the scales and staff's background characteristics (e.g. years of experience, gender). Child-care centres in the Netherlands. The qualitative pre-test included ten child-care staff members. The quantitative pilot test included 178 child-care staff members. The new questionnaire, the Child-care Food and Activity Practices Questionnaire (CFAPQ), consists of sixty-three items (forty food-related and twenty-three activity-related items), divided over twelve scales (seven food-related and five activity-related scales). The CFAPQ scales are to a large extent similar to the original CFPQ and PPAPP scales. The CFAPQ scales show sufficient internal consistency with Cronbach's α ranging between 0·53 and 0·96, and average corrected item-total correlations within acceptable ranges (0·30-0·89). Several of the scales were significantly associated with child-care staff's background characteristics. Scale psychometrics of the CFAPQ indicate it is a valid questionnaire that assesses child-care staff's practices related to both food and activities.

Slipstream pilot-scale demonstration of a novel amine-based post-combustion technology for carbon dioxide capture from coal-fired power plant flue gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krishnamurthy, Krish R.

Post-combustion CO 2 capture (PCC) technology offers flexibility to treat the flue gas from both existing and new coal-fired power plants and can be applied to treat all or a portion of the flue gas. Solvent-based technologies are today the leading option for PCC from commercial coal-fired power plants as they have been applied in large-scale in other applications. Linde and BASF have been working together to develop and further improve a PCC process incorporating BASF’s novel aqueous amine-based solvent technology. This technology offers significant benefits compared to other solvent-based processes as it aims to reduce the regeneration energy requirementsmore » using novel solvents that are very stable under the coal-fired power plant feed gas conditions. BASF has developed the desired solvent based on the evaluation of a large number of candidates. In addition, long-term small pilot-scale testing of the BASF solvent has been performed on a lignite-fired flue gas. In coordination with BASF, Linde has evaluated a number of options for capital cost reduction in large engineered systems for solvent-based PCC technology. This report provides a summary of the work performed and results from a project supported by the US DOE (DE-FE0007453) for the pilot-scale demonstration of a Linde-BASF PCC technology using coal-fired power plant flue gas at a 1-1.5 MWe scale in Wilsonville, AL at the National Carbon Capture Center (NCCC). Following a project kick-off meeting in November 2011 and the conclusion of pilot plant design and engineering in February 2013, mechanical completion of the pilot plant was achieved in July 2014, and final commissioning activities were completed to enable start-up of operations in January 2015. Parametric tests were performed from January to December 2015 to determine optimal test conditions and evaluate process performance over a variety of operation parameters. A long-duration 1500-hour continuous test campaign was performed from May to August 2016 at a selected process condition to evaluate process performance and solvent stability over a longer period similar to how the process would operate as a continuously running large-scale PCC plant. The pilot plant integrated a number of unique features of the Linde-BASF technology aimed at lowering overall energy consumption and capital costs. During the overall test period including startup, parametric testing and long-duration testing, the pilot plant was operated for a total of 6,764 hours out of which testing with flue gas was performed for 4,109 hours. The pilot plant testing demonstrated all of the performance targets including CO 2 capture rate exceeding 90%, CO 2 purity exceeding 99.9 mol% (dry), flue gas processing capacity up to 15,500 lbs/hr (equivalent to 1.5 MWe capacity slipstream), regeneration energy as low as 2.7 GJ/tonne CO 2, and regenerator operating pressure up to 3.4 bara. Excellent solvent stability performance data was measured and verified by Linde and BASF during both test campaigns. In addition to process data, significant operational learnings were gained from pilot tests that will contribute greatly to the commercial success of PCC. Based on a thorough techno-economic assessment (TEA) of the Linde-BASF PCC process integrated with a 550 MWe supercritical coal-fired power plant, the net efficiency of the integrated power plant with CO 2 capture is increased from 28.4% with the DOE/NETL Case 12 reference to 30.9% with the Linde-BASF PCC plant previously presented utilizing the BASF OASE® blue solvent [Ref. 4], and is further increased to 31.4% using a Linde-BASF PCC plant with BASF OASE® blue solvent and an advanced stripper interstage heater (SIH) configuration. The Linde-BASF PCC plant incorporating the BASF OASE® blue solvent also results in significantly lower overall capital costs, thereby reducing the cost of electricity (COE) and cost of CO 2 captured from $147.25/MWh and $56.49/MT CO 2, respectively, for the reference DOE/NETL Case 12 plant, to $128.49/MWh and $41.85/MT CO2 for process case LB1, respectively, and $126.65/MWh and $40.66/MT CO 2 for process case SIH, respectively. With additional innovative Linde-BASF PCC process configuration improvements, the COE and cost of CO 2 captured can be further reduced to $125.51/MWh and $39.90/MT CO 2 for a further optimized PCC process defined as LB1-CREB. Most notably, the Linde-BASF process options assessed have already demonstrated the potential to lower the cost of CO 2 captured below the DOE target of $40/MT CO 2 at the 550 MWe scale for second generation PCC technologies. Project organization, structure, goals, tasks, accomplishments, process criteria and milestones will be presented in this report along with highlights and key results from parametric and long-duration testing of the Linde-BASF PCC pilot. The parametric and long-duration testing campaigns were aimed at validating the performance of the PCC technology against targets determined from a preliminary techno-economic assessment. The stability of the solvent with extended operation in a realistic power plant setting was measured with performance verified. Additionally, general solvent classification information, process operating conditions, normalized solvent performance data, solvent stability test results, flue gas conditions data, CO 2 purity data in the gaseous product stream, steam requirements and process flow diagrams, and updated process economic data for a scaled-up 550 MWe supercritical power plant with CO 2 capture are presented and discussed in this report.« less

The optimization of aircraft seat cushion fire-blocking layers. Full Scale: Test description and results

NASA Technical Reports Server (NTRS)

Schutter, K. J.; Duskin, F. E.

1982-01-01

Full-scale burn tests were conducted on thirteen different seat cushion configurations in a cabin fire simulator. The fire source used was a quartz lamp radiant energy panel with a propane pilot flame. During each test, data were recorded for cushion temperatures, radiant heat flux, rate of weight loss of test specimens, and cabin temperatures. When compared to existing passenger aircraft seat cushions, the test specimens incorporating a fire barrier and those fabricated from advance materials, using improved construction methods, exhibited significantly greater fire resistance.

Tagging and Playback Studies to Toothed Whales

DTIC Science & Technology

2012-09-30

More playbacks of sonar have been conducted to pilot whales (Globicephala sp.), which are large pelagic delphinids, than to any other genus of cetacean...the group across different spatial scales. In particular, results showing how pilot whales use repeated, stereotyped calls (Sayigh et al. 2012) to re...establish contact with their social group following separations may prove valuable for testing whether monitoring for stereotyped calls might

Measuring hospital care from the patients' perspective: an overview of the CAHPS Hospital Survey development process.

PubMed

Goldstein, Elizabeth; Farquhar, Marybeth; Crofton, Christine; Darby, Charles; Garfinkel, Steven

2005-12-01

To describe the developmental process for the CAHPS Hospital Survey. A pilot was conducted in three states with 19,720 hospital discharges. A rigorous, multi-step process was used to develop the CAHPS Hospital Survey. It included a public call for measures, multiple Federal Register notices soliciting public input, a review of the relevant literature, meetings with hospitals, consumers and survey vendors, cognitive interviews with consumer, a large-scale pilot test in three states and consumer testing and numerous small-scale field tests. The current version of the CAHPS Hospital Survey has survey items in seven domains, two overall ratings of the hospital and five items used for adjusting for the mix of patients across hospitals and for analytical purposes. The CAHPS Hospital Survey is a core set of questions that can be administered as a stand-alone questionnaire or combined with a broader set of hospital specific items.

REDUCTION OF COAL-BASED METAL EMISSIONS BY FURNACE SORBENT INJECTION

EPA Science Inventory

The ability of sorbent injection technology to reduce the potential for trace metal emissions from coal combustion was researched. Pilot scale tests of high-temperature furnace sorbent injection were accompanied by stack sampling for coal-based, metallic air toxics. Tested sorben...

PILOT-SCALE INCINERATION TEST BURN OF TCDD-CONTAMINATED TRICHLOROPHENOL PRODUCTION WASTE

EPA Science Inventory

A series of three tests directed at evaluating the incinerability of the toluene stillbottoms waste from trichlorophenol production previously generated by the Vertac Chemical Company were performed in the Combustion Research Facility (CRF) rotary kiln incineration system. This w...

EMERGING TECHNOLOGY SUMMARY: REMOVAL AND RECOVERY OF METAL IONS FROM GROUNDWATER

EPA Science Inventory

A series of bench-scale tests and an onsite pilot scale demonstration of Bio-Recovery Systems' AlgaSORB® technology for the removal and recovery of mercury-contaminated groundwaters were conducted under the SITE program. The AlgaSORB® process is based on the natural, very st...

Development of clean coal and clean soil technologies using advanced agglomeration techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ignasiak, B.; Ignasiak, T.; Szymocha, K.

1990-01-01

Three major topics are discussed in this report: (1) Upgrading of Low Rank Coals by the Agflotherm Process. Test data, procedures, equipment, etc., are described for co-upgrading of subbituminous coals and heavy oil; (2) Upgrading of Bituminous Coals by the Agflotherm Process. Experimental procedures and data, bench and pilot scale equipments, etc., for beneficiating bituminous coals are described; (3) Soil Clean-up and Hydrocarbon Waste Treatment Process. Batch and pilot plant tests are described for soil contaminated by tar refuse from manufactured gas plant sites. (VC)

The Making of a Self-Neglect Severity Scale

NASA Technical Reports Server (NTRS)

Smith, Scott M.; Dyer, C. B.; Pavlik, V. N.; Kelly, P. A.; Lee, J.; Doody, R. S.; Regev, C.; Pickens, C.; Burnett, J.

2006-01-01

Research in elder self-neglect has lagged behind that of other forms of mistreatment, despite the fact that self-neglect is the most common allegation reported to Adult Protective Service agencies throughout the US. The lack of a gold-standard to measure self-neglect has hampered efforts to study this phenomenon. Researchers designed the Self-neglect Severity Scale (SSS) based on interviews with Adult Protective Service workers and a national expert panel. The SSS is based on observation and interview and is administered in the home to include an environmental assessment. It was piloted, extensively field tested and then revised. The CREST SSS was developed using survey data and consultation with experts in the field. This instrument utilizes observer ratings, interview responses, and assesses subjects physical and environmental domains. It also assesses functional status as it relates to health and safety issues. After field and pilot testing the SSS was finalized and is currently undergoing reliability and validity testing. The CREST SSS was developed as a state scale to provide a common language for describing cases of self-neglect. It is the first self-neglect severity scale available to researchers. If found to be both reliable and valid it can be used in future intervention studies.

The making of a self-neglect severity scale.

PubMed

Dyer, Carmel Bitondo; Kelly, P Adam; Pavlik, Valory N; Lee, Jessica; Doody, Rachelle S; Regev, Tziona; Pickens, Sabrina; Burnett, Jason; Smith, Scott M

2006-01-01

Research in elder self-neglect has lagged behind that of other forms of mistreatment, despite the fact that self-neglect is the most common allegation reported to Adult Protective Service agencies throughout the US. The lack of a gold standard to measure self-neglect has hampered efforts to study this phenomenon. Researchers designed the Self-Neglect Severity Scale (SSS) based on interviews with Adult Protective Service workers and a national expert panel. The SSS is based on observation and interview and is administered in the home to include an environmental assessment. It was piloted, extensively field tested and then revised. The CREST SSS was developed using survey data and consultation with experts in the field. This instrument utilizes observer ratings, interview responses, and assesses subjects' physical and environmental domains. It also assesses functional status as it relates to health and safety issues. After field and pilot testing, the SSS was finalized and is currently undergoing reliability and validity testing. The CREST SSS was developed as a state scale to provide a common language for describing cases of self-neglect. It is the first self-neglect severity scale available to researchers. If found to be both reliable and valid, it may be used in future intervention studies.

Young Children's Participation and Environment Measure: Swedish Cultural Adaptation.

PubMed

Åström, Frida Marie; Khetani, Mary; Axelsson, Anna Karin

2018-08-01

To culturally adapt and evaluate the psychometric properties of the Young Children's Participation and Environment Measure (YC-PEM) for use by caregivers of Swedish children with and without disabilities, aged 2-5 years. Thirteen cognitive interviews and two focus groups with caregivers of children with and without disabilities were conducted to evaluate the cultural relevance of YC-PEM content for use in Sweden. Per participant feedback, a revised version of the Swedish YC-PEM was created and pilot tested with caregivers of children with disabilities (n = 11) and children with typical development (n = 22). User feedback informed content revisions to 7% of items. Internal consistency estimates of the Swedish YC-PEM pilot version were acceptable and ranged from .70 to .92 for all but two of the YC-PEM scales. Mean percentage agreement between raters ranged from 47% to 93% across YC-PEM scales for inter-rater, and 44% to 86% for test-retest. One of twelve YC-PEM scales revealed significant group differences between young children with and without disabilities. This study contributes preliminary evidence for the use of some scales within a culturally adapted YC-PEM in Sweden. Further validation with larger samples will allow for parametric testing to evaluate its psychometric properties.

Procedures for Scaling the 1990 Edition of the Nevada Proficiency Examinations in Reading and Mathematics.

ERIC Educational Resources Information Center

Klein, Thomas W.

Steps involved in the item analysis and scaling of the 1990 edition of Forms A and B of the Nevada High School Proficiency Examinations (NHSPEs) are described. Pilot tests of Forms A and B of the 47-item reading and 45-item mathematics tests were each administered to random samples of more than 600 eleventh-grade students. A computer program was…

Bioretention Design to Improve Nitrogen Removal | Science ...

EPA Pesticide Factsheets

Bioretention has been shown to effectively remove a variety of stormwater stressors, including oil/grease, heavy metals, phosphorus, and ammonium. However, reported nitrate and total nitrogen removal performance is highly variable. The media typically used in bioretention installation is coarse-grained with low organic matter content, which facilitates high infiltration rates but fails to provide the anaerobic conditions and carbon availability necessary to promote nitrate removal by denitrification. EPA's research at the Urban Watershed Research Facility investigates the effects of media carbon amendments, introduced internal storage zones, plant type, and media volume on nitrogen removal. Initial bench-scale tests informed media and carbon amendment choices. A locally-available, sandy media with low organic matter content was added to eight experimental, pilot-scale rain gardens above a shallow pea gravel drainage layer. The media was separated from the pea gravel with a nonwoven geotextile. Double-shredded hardwood wood chips were chosen as a carbon amendment and added as a 20-cm layer 10 cm above the geotextile in four of the eight pilot-scale rain gardens; the other four did not receive the mulch layer. Four rain gardens were constructed with an elevated outlet pipe to create an internal storage zone; the other four drain freely. Pilot-scale rain gardens were constructed in tanks of two sizes to test the effects of media volume. After initial hydrologic

Pilot-scale study on the treatment of basal aquifer water using ultrafiltration, reverse osmosis and evaporation/crystallization to achieve zero-liquid discharge.

PubMed

Loganathan, Kavithaa; Chelme-Ayala, Pamela; Gamal El-Din, Mohamed

2016-01-01

Basal aquifer water is deep groundwater found at the bottom of geological formations, underlying bitumen-saturated sands. Some of the concerns associated with basal aquifer water at the Athabasca oil sands are the high concentrations of hardness-causing compounds, alkalinity, and total dissolved solids. The objective of this pilot-scale study was to treat basal aquifer water to a quality suitable for its reuse in the production of synthetic oil. To achieve zero-liquid discharge (ZLD) conditions, the treatment train included chemical oxidation, polymeric ultrafiltration (UF), reverse osmosis (RO), and evaporation-crystallization technologies. The results indicated that the UF unit was effective in removing solids, with UF filtrate turbidity averaging 2.0 NTU and silt density index averaging 0.9. Membrane autopsies indicated that iron was the primary foulant on the UF and RO membranes. Laboratory and pilot-scale tests on RO reject were conducted to determine the feasibility of ZLD crystallization. Due to the high amounts of calcium, magnesium, and bicarbonate in the RO reject, softening of the feed was required to avoid scaling in the evaporator. Crystals produced throughout the testing were mainly sodium chloride. The results of this study indicated that the ZLD approach was effective in both producing freshwater and minimizing brine discharges. Copyright © 2015 Elsevier Ltd. All rights reserved.

Flying Qualities Evaluation of a Commuter Aircraft With an Ice Contaminated Tailplane

NASA Technical Reports Server (NTRS)

Ranaudo, Richard J.; Ratvasky, Thomas P.; FossVanZante, Judith

2000-01-01

During the NASA/FAA (Federal Aviation Administration) Tailplane Icing Program, pilot evaluations of aircraft flying qualities were conducted with various ice shapes attached to the horizontal tailplane of the NASA Twin Otter Icing Research Aircraft. Initially, only NASA pilots conducted these evaluations, assessing the differences in longitudinal flight characteristics between the baseline or clean aircraft, and the aircraft configured with an Ice Contaminated Tailplane (ICT). Longitudinal tests included Constant Airspeed Flap Transitions, Constant Airspeed Thrust Transitions, zero-G Pushovers, Repeat Elevator Doublets, and Simulated Approach and Go-Around tasks. Later in the program, guest pilots from government and industry were invited to fly the NASA Twin Otter configured with a single full-span artificial ice shape attached to the leading edge of the horizontal tailplane. This shape represented ice formed due to a 'Failed Boot' condition, and was generated from tests in the Glenn Icing Research Tunnel on a full-scale tailplane model. Guest pilots performed longitudinal handling tests, similar to those conducted by the NASA pilots, to evaluate the ICT condition. In general, all pilots agreed that longitudinal flying qualities were degraded as flaps were lowered, and further degraded at high thrust settings. Repeat elevator doublets demonstrated reduced pitch damping effects due to ICT, which is a characteristic that results in degraded flying qualities. Pilots identified elevator control force reversals (CFR) in zero-G pushovers at a 20 deg flap setting, a characteristic that fails the FAR 25 no CFR certification requirement. However, when the same pilots used the Cooper-Harper rating scale to perform a simulated approach and go-around task at the 20 deg flap setting, they rated the airplane as having Level I and Level II flying qualities respectively. By comparison, the same task conducted at the 30 deg flap setting, resulted in Level II flying qualities for the approach portion, and Level III for the go-around portion.The results of this program indicate that safe and acceptable flying qualities with an ICT condition, can be effectively assessed by task-oriented pilot maneuvers. In addition, other maneuvers such as repeat elevator doublets provide good qualitative and quantitative assessments of pitch damping and elevator effectiveness, which are characteristics that correlate well with pilot task ratings. The results of this testing indicate that the FAR 25 zero-G pushover maneuver, which requires no CFR during its execution, may be an overly conservative pass/fail criteria for aircraft certification.

CONTROL TECHNOLOGIES: PILOT- & FULL-SCALE TESTS

EPA Science Inventory

Two different project are to be supported in FY03. The first project is being conducted by the North Dakota Energy and Environmental Research Center (ND-EERC). This project consists of tests on coal-fired utility boilers to determine the effects of SCR catalysts and ammonia in...

CFD Modeling of Flow, Temperature, and Concentration Fields in a Pilot-Scale Rotary Hearth Furnace

NASA Astrophysics Data System (ADS)

Liu, Ying; Su, Fu-Yong; Wen, Zhi; Li, Zhi; Yong, Hai-Quan; Feng, Xiao-Hong

2014-01-01

A three-dimensional mathematical model for simulation of flow, temperature, and concentration fields in a pilot-scale rotary hearth furnace (RHF) has been developed using a commercial computational fluid dynamics software, FLUENT. The layer of composite pellets under the hearth is assumed to be a porous media layer with CO source and energy sink calculated by an independent mathematical model. User-defined functions are developed and linked to FLUENT to process the reduction process of the layer of composite pellets. The standard k-ɛ turbulence model in combination with standard wall functions is used for modeling of gas flow. Turbulence-chemistry interaction is taken into account through the eddy-dissipation model. The discrete ordinates model is used for modeling of radiative heat transfer. A comparison is made between the predictions of the present model and the data from a test of the pilot-scale RHF, and a reasonable agreement is found. Finally, flow field, temperature, and CO concentration fields in the furnace are investigated by the model.

High power Nb-doped LiFePO4 Li-ion battery cathodes; pilot-scale synthesis and electrochemical properties

NASA Astrophysics Data System (ADS)

Johnson, Ian D.; Blagovidova, Ekaterina; Dingwall, Paul A.; Brett, Dan J. L.; Shearing, Paul R.; Darr, Jawwad A.

2016-09-01

High power, phase-pure Nb-doped LiFePO4 (LFP) nanoparticles are synthesised using a pilot-scale continuous hydrothermal flow synthesis process (production rate of 6 kg per day) in the range 0.01-2.00 at% Nb with respect to total transition metal content. EDS analysis suggests that Nb is homogeneously distributed throughout the structure. The addition of fructose as a reagent in the hydrothermal flow process, followed by a post synthesis heat-treatment, affords a continuous graphitic carbon coating on the particle surfaces. Electrochemical testing reveals that cycling performance improves with increasing dopant concentration, up to a maximum of 1.0 at% Nb, for which point a specific capacity of 110 mAh g-1 is obtained at 10 C (6 min for the charge or discharge). This is an excellent result for a high power cathode LFP based material, particularly when considering the synthesis was performed on a large pilot-scale apparatus.

Thermal/structural modeling of a large scale in situ overtest experiment for defense high level waste at the Waste Isolation Pilot Plant Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, H.S.; Stone, C.M.; Krieg, R.D.

Several large scale in situ experiments in bedded salt formations are currently underway at the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico, USA. In these experiments, the thermal and creep responses of salt around several different underground room configurations are being measured. Data from the tests are to be compared to thermal and structural responses predicted in pretest reference calculations. The purpose of these comparisons is to evaluate computational models developed from laboratory data prior to fielding of the in situ experiments. In this paper, the computational models used in the pretest reference calculation for one of themore » large scale tests, The Overtest for Defense High Level Waste, are described; and the pretest computed thermal and structural responses are compared to early data from the experiment. The comparisons indicate that computed and measured temperatures for the test agree to within ten percent but that measured deformation rates are between two and three times greater than corresponsing computed rates. 10 figs., 3 tabs.« less

Effect of Alternate Nostril Breathing Exercise on Experimentally Induced Anxiety in Healthy Volunteers Using the Simulated Public Speaking Model: A Randomized Controlled Pilot Study.

PubMed

Kamath, Ashwin; Urval, Rathnakar P; Shenoy, Ashok K

2017-01-01

A randomized controlled pilot study was carried out to determine the effect of a 15-minute practice of ANB exercise on experimentally induced anxiety using the simulated public speaking model in yoga-naïve healthy young adults. Thirty consenting medical students were equally divided into test and control groups. The test group performed alternate nostril breathing exercise for 15 minutes, while the control group sat in a quiet room before participating in the simulated public speaking test (SPST). Visual Analog Mood Scale and Self-Statements during Public Speaking scale were used to measure the mood state at different phases of the SPST. The psychometric scores of both groups were comparable at baseline. Repeated-measures ANOVA showed a significant effect of phase ( p < 0.05), but group and gender did not have statistically significant influence on the mean anxiety scores. However, the test group showed a trend towards lower mean scores for the anxiety factor when compared with the control group. Considering the limitations of this pilot study and the trend seen towards lower anxiety in the test group, alternate nostril breathing may have potential anxiolytic effect in acute stressful situations. A study with larger sample size is therefore warranted. This trial is registered with CTRI/2014/03/004460.

Effect of Alternate Nostril Breathing Exercise on Experimentally Induced Anxiety in Healthy Volunteers Using the Simulated Public Speaking Model: A Randomized Controlled Pilot Study

PubMed Central

Urval, Rathnakar P.; Shenoy, Ashok K.

2017-01-01

A randomized controlled pilot study was carried out to determine the effect of a 15-minute practice of ANB exercise on experimentally induced anxiety using the simulated public speaking model in yoga-naïve healthy young adults. Thirty consenting medical students were equally divided into test and control groups. The test group performed alternate nostril breathing exercise for 15 minutes, while the control group sat in a quiet room before participating in the simulated public speaking test (SPST). Visual Analog Mood Scale and Self-Statements during Public Speaking scale were used to measure the mood state at different phases of the SPST. The psychometric scores of both groups were comparable at baseline. Repeated-measures ANOVA showed a significant effect of phase (p < 0.05), but group and gender did not have statistically significant influence on the mean anxiety scores. However, the test group showed a trend towards lower mean scores for the anxiety factor when compared with the control group. Considering the limitations of this pilot study and the trend seen towards lower anxiety in the test group, alternate nostril breathing may have potential anxiolytic effect in acute stressful situations. A study with larger sample size is therefore warranted. This trial is registered with CTRI/2014/03/004460. PMID:29159176

Biological treatment of whey by Tetrahymena pyriformis and impact study on laboratory-scale wastewater lagoon process.

PubMed

Bonnet, J L; Bogaerts, P; Bohatier, J

1999-06-01

A procedure based on a biological treatment of whey was tested as part of research on waste treatment at the scale of small cheesemaking units. We studied the potential biodegradation of whey by a protozoan ciliate, Tetrahymena pyriformis, and evaluated the functional, microbiological and physiological disturbances caused by crude whey and the biodegraded whey in laboratory-scale pilots mimicking a natural lagoon treatment. The results show that T. pyriformis can strongly reduce the pollutant load of whey. In the lagoon pilots serving as example of receptor media, crude whey gradually but completely arrested operation, whereas with the biodegraded whey adverse effects were only temporary, and normal operation versus a control was gradually recovered in a few days.

Waveforms and Sonic Boom Perception and Response (WSPR): Low-Boom Community Response Program Pilot Test Design, Execution, and Analysis

NASA Technical Reports Server (NTRS)

Page, Juliet A.; Hodgdon, Kathleen K.; Krecker, Peg; Cowart, Robbie; Hobbs, Chris; Wilmer, Clif; Koening, Carrie; Holmes, Theresa; Gaugler, Trent; Shumway, Durland L.;

The Poverty and Housing Scale: report on a pilot study.

PubMed

Galambos, Colleen M; MacMaster, Samuel A

2004-01-01

The measurement of beliefs and attitudes on poverty and housing is important to researchers and social workers interested in examining the role that belief structures have on the development of policy and programs in these areas. This article reports pilot study findings of a new scale, The Poverty and Housing Scale (PHS), that measures this concept and evaluates its psychometric properties. Preliminary reliability was in the very good range. Examinations of content and face validity provided support of the instrument as a valid measure of beliefs and attitudes on poverty and housing. The factor analysis emerged a one factor, 13-item scale. Unlike other related scales, the PHS attempts to link the social factor of poverty and housing together. Theoretical and methodological strengths and weaknesses are considered and the implications for social work practice are discussed. The authors provide recommendations for additional testing of the instrument.

Developmental neuropsychological assessment of 4- to 5-year-old children born following Preimplantation Genetic Diagnosis (PGD): A pilot study.

PubMed

Sacks, Gilat Chaya; Altarescu, Gheona; Guedalia, Judith; Varshaver, Irit; Gilboa, Tal; Levy-Lahad, Ephrat; Eldar-Geva, Talia

2016-01-01

The purpose of this pilot study was to evaluate developmental neuropsychological profiles of 4- to 5-year-old children born after Preimplantation Genetic Diagnosis (PGD). Twenty-seven participants received a neurological examination and a battery of neuropsychological assessments including Wechsler Preschool & Primary Scale of Intelligence - Third Edition (WPPSI-III; cognitive development), Preschool Language Scale, Fourth Edition (PLS-4; language development), Wide Range Assessment of Visual Motor Abilities (visual motor abilities), Childhood Autism Rating Scales II (a screening test for autistic spectrum disorders), and the Miles ABC Test (ocular dominance). Parental questionnaires included the Behavior Rating Inventory of Executive Function Preschool Version (BRIEF-P; executive function), Child Behavior Checklist (CBCL) and the Carey Temperament Scales Behavioral Style Questionnaire (socioemotional development and temperament), and the Vineland Adaptive Behavior Scales, Interview Edition, Second Edition (general adaptive behavior). Subjects' tests results were compared to each test's norms. Children born after PGD demonstrated scores within the normal or above-normal ranges for all developmental outcomes (mean ± SD): WPPSI-III-VIQ 107.4 ± 14.4 (p = .013), PLS-4-Total 113.2 ± 12.4, p < .001), CBCL-Total 41.1 ± 8.6 (p < .001), BRIEF-P-Global Executive Composite 44.8 ± 9.5 (p = .009). Twelve (44%) of the PGD children had a significant difference between their VIQ and PIQ scores (compared to 27% in the general population). One subject was found to show possible signs of autistic spectrum disorder, although a family history of autism was noted. In conclusion, in this pilot study, children assessed at age 4-5 years and conceived after PGD displayed developmental neuropsychological outcomes within normal limits as compared to their chronologic peers. A larger study is needed to evaluate and follow the neuropsychological development of children born after PGD.

Predictor Development and Pilot Testing of a Prototype Selection Instrument for Army Flight Training

DTIC Science & Technology

2007-02-01

called the Automated Pilot Examination System, or "APEX") during the preliminary validation reserach . The current version of the ASTB includes subtests...of objects in three-dimensional space . Aviation & Nautical Information: items assess an examinee’s familiarity with aviation history, nautical...proficiency. Aviation, Space and Environmental Medicine, 46, 309-311. Daryanian, B. (1980). Subjective scaling of mental workload in a multi-task environment

Pilot plant test of the advanced flash stripper for CO2 capture.

PubMed

Lin, Yu-Jeng; Chen, Eric; Rochelle, Gary T

2016-10-20

Alternative stripping processes have been proposed to reduce energy use for CO 2 capture, but only a few have been applied to pilot-scale experiments. This paper presents the first pilot plant test results of one of the most promising stripper configurations, the advanced flash stripper with cold and warm rich solvent bypass. The campaign using aqueous piperazine was carried out at UT Austin in 2015. The advanced flash stripper improves the heat duty by over 25% compared to previous campaigns using the two-stage flash, achieving 2.1 GJ per tonne CO 2 of heat duty and 32 kJ mol -1 CO 2 of total equivalent work. The bypass control strategy proposed minimized the heat duty. The test successfully demonstrated the remarkable energy performance and the operability of this advanced system. An Aspen Plus® model was validated using the pilot plant data and used to explore optimum operating and design conditions. The irreversibility analysis showed that the pilot plant performance has attained 50% thermodynamic efficiency and further energy improvement should focus on the absorber and the cross exchanger by increasing absorption rate and solvent capacity.

Great Basin Integrated Landscape Monitoring Pilot Summary Report

USGS Publications Warehouse

Finn, Sean P.; Kitchell, Kate; Baer, Lori Anne; Bedford, David R.; Brooks, Matthew L.; Flint, Alan L.; Flint, Lorraine E.; Matchett, J.R.; Mathie, Amy; Miller, David M.; Pilliod, David S.; Torregrosa, Alicia; Woodward, Andrea

2010-01-01

The Great Basin Integrated Landscape Monitoring Pilot project (GBILM) was one of four regional pilots to implement the U.S. Geological Survey (USGS) Science Thrust on Integrated Landscape Monitoring (ILM) whose goal was to observe, understand, and predict landscape change and its implications on natural resources at multiple spatial and temporal scales and address priority natural resource management and policy issues. The Great Basin is undergoing rapid environmental change stemming from interactions among global climate trends, increasing human populations, expanding and accelerating land and water uses, invasive species, and altered fire regimes. GBLIM tested concepts and developed tools to store and analyze monitoring data, understand change at multiple scales, and forecast landscape change. The GBILM endeavored to develop and test a landscape-level monitoring approach in the Great Basin that integrates USGS disciplines, addresses priority management questions, catalogs and uses existing monitoring data, evaluates change at multiple scales, and contributes to development of regional monitoring strategies. GBILM functioned as an integrative team from 2005 to 2010, producing more than 35 science and data management products that addressed pressing ecosystem drivers and resource management agency needs in the region. This report summarizes the approaches and methods of this interdisciplinary effort, identifies and describes the products generated, and provides lessons learned during the project.

Pilot study of a targeted dance class for physical rehabilitation in children with cerebral palsy.

PubMed

López-Ortiz, Citlali; Egan, Tara; Gaebler-Spira, Deborah J

2016-01-01

This pilot study evaluates the effects of a targeted dance class utilizing classical ballet principles for rehabilitation of children with cerebral palsy on balance and upper extremity control. Twelve children with cerebral palsy (ages 7-15 years) with Gross Motor Function Classification scores II-IV participated in this study and were assigned to either a control group or targeted dance class group. Targeted dance class group participated in 1-h classes three times per week in a 4-week period. The Pediatric Balance Scale and the Quality of Upper Extremity Skills Test were administered before, after, and 1 month after the targeted dance class. Improvements in the Pediatric Balance Scale were present in the targeted dance class group in before versus after and before versus 1 month follow-up comparisons (p-value = 0.0088 and p-value = 0.019, respectively). The Pediatric Balance Scale changes were not significant in the control group. The Quality of Upper Extremity Skills Test did not reach statistical differences in either group. Classical ballet as an art form involves physical training, musical accompaniment, social interactions, and emotional expression that could serve as adjunct to traditional physical therapy. This pilot study demonstrated improvements in balance control. A larger study with a more homogeneous sample is warranted.

Interpreted Cooper-Harper for broader use

NASA Technical Reports Server (NTRS)

Green, David L.; Andrews, Hal; Gallagher, Donald W.

1993-01-01

The current aircraft assessment process typically makes extensive use of operational personnel during simulations and operational evaluations, with increased emphasis on evaluating the many pilot and/or operator/aircraft control loops. The need for a crew assessment in this broader arena has produced a variety of rating scales. The Cooper-Harper Rating Scale is frequently misused and routinely overlooked in the process, for these applications often extend the scale's use beyond its originally intended application. This paper agrees with the broader application of the Cooper-Harper Rating Scale and presents a concept for the development of a 'use unique' Interpreted Cooper-Harper Scale to help achieve this objective. This interpreted scale concept was conceived during efforts to support an FAA evaluation of a night vision enhancement system. It includes descriptive extensions, which are faithful to the intent of the current Cooper-Harper Scale and should provide the kind of detail that has historically been provided by trained test pilots in their explanatory comments.

A Pilot Test of the Additive Benefits of Physical Exercise to CBT for OCD.

PubMed

Rector, Neil A; Richter, Margaret A; Lerman, Bethany; Regev, Rotem

2015-01-01

The majority of "responders" to first-line cognitive-behavioural therapy (CBT) and pharmacological treatments for obsessive-compulsive disorder (OCD) are left with residual symptoms that are clinically relevant and disabling. Therefore, there is pressing need for widely accessible efficacious alternative and/or adjunctive treatments for OCD. Accumulating evidence suggests that physical exercise may be one such intervention in the mood and anxiety disorders broadly, although we are aware of only two positive small-scale pilot studies that have tested its clinical benefits in OCD. This pilot study aimed to test the feasibility and preliminary efficacy of adding a structured physical exercise programme to CBT for OCD. A standard CBT group was delivered concurrently with a 12-week customized exercise programme to 11 participants. The exercise regimen was individualized for each participant based on peak heart rate measured using an incremental maximal exercise test. Reports of exercise adherence across the 12-week regimen exceeded 80%. A paired-samples t-test indicated very large treatment effects in Yale-Brown Obsessive-Compulsive Scale scores from pre- to post-treatment in CBT group cohorts led by expert CBT OCD specialists (d = 2.55) and junior CBT clinician non-OCD specialists (d = 2.12). These treatment effects are very large and exceed effects typically observed with individual and group-based CBT for OCD based on leading meta-analytic reviews, as well as previously obtained treatment effects for CBT using the same recruitment protocol without exercise. As such, this pilot work demonstrates the feasibility and significant potential clinical utility of a 12-week aerobic exercise programme delivered in conjunction with CBT for OCD.

Blockage and flow studies of a generalized test apparatus including various wing configurations in the Langley 7-inch Mach 7 Pilot Tunnel

NASA Astrophysics Data System (ADS)

Albertson, C. W.

1982-03-01

A 1/12th scale model of the Curved Surface Test Apparatus (CSTA), which will be used to study aerothermal loads and evaluate Thermal Protection Systems (TPS) on a fuselage-type configuration in the Langley 8-Foot High Temperature Structures Tunnel (8 ft HTST), was tested in the Langley 7-Inch Mach 7 Pilot Tunnel. The purpose of the tests was to study the overall flow characteristics and define an envelope for testing the CSTA in the 8 ft HTST. Wings were tested on the scaled CSTA model to select a wing configuration with the most favorable characteristics for conducting TPS evaluations for curved and intersecting surfaces. The results indicate that the CSTA and selected wing configuration can be tested at angles of attack up to 15.5 and 10.5 degrees, respectively. The base pressure for both models was at the expected low level for most test conditions. Results generally indicate that the CSTA and wing configuration will provide a useful test bed for aerothermal pads and thermal structural concept evaluation over a broad range of flow conditions in the 8 ft HTST.

Blockage and flow studies of a generalized test apparatus including various wing configurations in the Langley 7-inch Mach 7 Pilot Tunnel

NASA Technical Reports Server (NTRS)

Albertson, C. W.

1982-01-01

A 1/12th scale model of the Curved Surface Test Apparatus (CSTA), which will be used to study aerothermal loads and evaluate Thermal Protection Systems (TPS) on a fuselage-type configuration in the Langley 8-Foot High Temperature Structures Tunnel (8 ft HTST), was tested in the Langley 7-Inch Mach 7 Pilot Tunnel. The purpose of the tests was to study the overall flow characteristics and define an envelope for testing the CSTA in the 8 ft HTST. Wings were tested on the scaled CSTA model to select a wing configuration with the most favorable characteristics for conducting TPS evaluations for curved and intersecting surfaces. The results indicate that the CSTA and selected wing configuration can be tested at angles of attack up to 15.5 and 10.5 degrees, respectively. The base pressure for both models was at the expected low level for most test conditions. Results generally indicate that the CSTA and wing configuration will provide a useful test bed for aerothermal pads and thermal structural concept evaluation over a broad range of flow conditions in the 8 ft HTST.

Comparison between Synthesized Lead Particles and Lead Solids Formed on Surfaces in Real Drinking Water Distribution Systems

EPA Science Inventory

The objective of this work is to compare the properties of lead solids formed during bench-scale precipitation experiments to solids found on lead pipe removed from real drinking water distribution systems and metal coupons used in pilot scale corrosion testing. Specifically, so...

Chemical additive to maximize antimicrobial effect of chlorine during pilot scale immersion chilling of broiler carcasses

USDA-ARS?s Scientific Manuscript database

A prior laboratory scale study demonstrated the potential for T-128, a proprietary blend including propylene glycol and phosphoric acid, to enhance the antimicrobial efficacy of chlorine during immersion chilling of broiler parts. The objective of the current study was to test the addition of T-128...

The Children's Perceived Locus of Causality Scale for Physical Education

ERIC Educational Resources Information Center

Pannekoek, Linda; Piek, Jan P.; Hagger, Martin S.

2014-01-01

A mixed methods design was applied to evaluate the application of the Perceived Locus of Causality scale (PLOC) to preadolescent samples in physical education settings. Subsequent to minor item adaptations to accommodate the assessment of younger samples, qualitative pilot tests were performed (N = 15). Children's reports indicated the need…

EZVI Injection Field Test Leads to Pilot-Scale Application

EPA Science Inventory

Testing and monitoring of emulsified zero-valent ironTM (EZVI) injections was conducted at Cape Canaveral Air Force Station’s Launch Complex 34, FL, in 2002 to 2005 to evaluate the technology’s efficacy in enhancing in situ dehalogenation of dense nonaqueous-phase liquid (DNAPL) ...

FIELD TEST OF NONFUEL HYDROCARBON BIOVENTING IN CLAYEY-SAND SOIL

EPA Science Inventory

A pilot-scale bioventing test was conducted at the Greenwood Chemical Superfund Site in Virginia. The characteristics of the site included clayey-sand soils and nonfuel organic contamination such as acetone, toluene, and naphthalene in the vadose zone. Based on the results of an...

ATD Occupant Responses from Three Full-Scale General Aviation Crash Tests

NASA Technical Reports Server (NTRS)

Littell, Justin D.; Annett, Martin S.

2016-01-01

During the summer of 2015, three Cessna 172 General Aviation (GA) aircraft were crash tested at the Landing and Impact Research (LandIR) Facility at NASA Langley Research Center (LaRC). Three different crash scenarios were represented. The first test simulated a flare-to-stall emergency or hard landing onto a rigid surface such as a road or runway. The second test simulated a controlled flight into terrain with a nose down pitch of the aircraft, and the third test simulated a controlled flight into terrain with an attempt to unsuccessfully recover the aircraft immediately prior to impact, resulting in a tail strike condition. An on-board data acquisition system (DAS) captured 64 channels of airframe acceleration, along with accelerations and loads in two onboard Hybrid II 50th percentile Anthropomorphic Test Devices (ATDs) representing the pilot and copilot. Each of the three tests contained different airframe loading conditions and different types of restraints for both the pilot and co-pilot ATDs. The results show large differences in occupant response and restraint performance with varying likelihoods of occupant injury.

The Response Scale for the Intellectual Disability Module of the WHOQOL: 5-Point or 3-Point?

ERIC Educational Resources Information Center

Fang, J.; Fleck, M. P.; Green, A.; McVilly, K.; Hao, Y.; Tan, W.; Fu, R.; Power, M.

2011-01-01

Objective: To deal with the question of whether a 5-point response Likert scale should be changed to a 3-point scale when used in the field testing of people with intellectual disabilities (IDs), which was raised after the pilot study of World Health Organization Quality of Life (WHOQOL)-DIS, a module being developed with the World Health…

Pyrolysis of coal, biomass and their blends: performance assessment by thermogravimetric analysis.

PubMed

Ferrara, Francesca; Orsini, Alessandro; Plaisant, Alberto; Pettinau, Alberto

2014-11-01

With the aim to support the experimental tests in a gasification pilot plant, the thermal decomposition of coal, biomass and their mixtures has been carried out through a thermogravimetric analysis (TGA) and a simplified kinetic analysis. The TGA of pure fuels indicates the low reactivity of South African coal and the relatively high reactivity of Sardinian Sulcis coal during pyrolysis. Among the tested fuels, biomass (stone pine wood chips) is the most reactive one. These results fully confirm those obtained during the experimental tests in the gasification pilot plant. As for the fuel blends, the analysis shows that the synergic effects between the considered coals and biomass are negligible when they are co-pyrolyzed. The results of the analysis confirm that TGA could be very useful to generally predict the gasification performance and to optimize the experimental campaigns in pilot-scale gasification plants. Copyright © 2014 Elsevier Ltd. All rights reserved.

Free-Spinning-Tunnel Tests of a 1/16-Scale Model of the Chance Vought XF5U-1 Airplane, TED No. NACA 2349

NASA Technical Reports Server (NTRS)

White, Richard P.

1947-01-01

Spin tests of a 1/16-scale model of the Chance Vought XF5U-1 airplane have been performed in the Langley 20-foot free-spinning tunnel. The effect of control position and movement upon the erect and inverted spin and recovery characteristics ae well as the effects of propellers, of stability flaps, and of various revisions to the design configuration have been determined for the normal fighter loading. The investigation also included spin recovery parachute, tumbling, and pilot-escape tests. For the original design configuration, with or without windmilling propellers, the recovery characteristics of the model were considered unsatisfactory. Increasing the maximum upward deflection of the ailavators from 45 deg to 65 deg resulted in greatly improved recovery characteristics. Dimensional revisions to the original airplane configuration, which satisfactorily improved the general spin and recovery characteristics of the model, consisted of: (1) a supplementary vertical tail 34 inches by 59 inches (full-scale) attached to a boom 80 inches aft of the trailing edge of the airplane in the plane of symmetry, (2) a large semispan undersurface spoiler placed along the airplane quarter-chord line and opened on the outboard side in a spin, or (3) two additional vertical tails 64 inches by 52 inches (full-scale) located at the tips of the ailavators. A satisfactory parachute arrangement for emergency spin recovery from demonstration spins was found to be an arrangement consisting of a 13.3-foot parachute attached by a 30-foot towline to the arresting gear mast on the airplane and opened simultaneously with an 8-foot parachute on the outboard end of the wing attached by a 3-foot towline. Tests indicated that pilot escape from a spin would be extremely hazardous unless the pilot is mechanically ejected from the cockpit. Model tumbling tests indicated that the airplane would not tumble.

WIPP (Waste Isolation Pilot Plant) intermediate scale borehole test: A pretest analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Argueello, J.G.

A three-dimensional finite element structural analysis of the Intermediate Scale Borehole Test at the Waste Isolation Pilot Plant (WIPP) has been performed. The analysis provides insight into how a relatively new excavation in a creeping medium responds when introduced into an existing pillar which has been undergoing stress redistribution for 5.7 years. The stress field of the volume of material in the immediate vicinity of the borehole changes significantly when the hole is drilled. Closure of the hole is predicted to be larger in the vertical direction than in the horizontal direction, leading to an ovaling of the hole. Themore » relatively high stresses near the hole persist even at the end of the simulation, 2 years after the hole is drilled. 12 ref., 10 figs.« less

Developing a pressure ulcer risk assessment scale for patients in long-term care.

PubMed

Lepisto, Mervi; Eriksson, Elina; Hietanen, Helvi; Lepisto, Jyri; Lauri, Sirkka

2006-02-01

Previous pressure ulcer risk assessment scales appear to have relied on opinions about risk factors and are based on care setting rather than research evidence. Utilizing 21 existing risk assessment scales and relevant risk factor literature, an instrument was developed by Finnish researchers that takes into account individual patient risk factors, devices and methods applied in nursing care, and organizational characteristics. The instrument underwent two pilot tests to assess the relevance and clarity of the instrument: the first involved 43 nurses and six patients; the second involved 50 nurses with expertise in wound care. Changes to questionnaire items deemed necessary as a result of descriptive analysis and agreement percentages were completed. After pilot testing, the final instrument addressed the following issues: 1) patient risks: activity, mobility in bed, mental status, nutrition, urinary incontinence, fecal incontinence, sensory perception, and skin condition; 2) devices and methods used in patient care: technical devices, bed type, mattress, overlay, seat cushions, and care methods; and 3) staff number and structure, maximum number of beds, and beds in use (the last group of questions were included to ensure participants understood the items; results were not analyzed). The phases of the study provided an expeditious means of data collection and a suitable opportunity to assess how the instrument would function in practice. Instrument reliability and validity were improved as a result of the pilot testing and can be enhanced further with continued use and assessment.

Conduct and Results of YF-16 RPRV Stall/Spin Drop Model Tests

DTIC Science & Technology

1977-04-01

Bomb Recovery System Tests Iron Bird Recovery System Tests Captive Flights Typical Flight Operations Flight Planning and Pilot Training...helicopter tow qualification test, one model tow qualification test, three Iron Bird parachute recovery system verification tests, three captive tests...Corresponding Full-Scale YF-16 Altitude -Reference 1: Woodcock , Robert J., Some Notes on Free-Flight Model Seal- ing, AFFDL-TM-73-123-FCC, Air Force Flight

Visual/motion cue mismatch in a coordinated roll maneuver

NASA Technical Reports Server (NTRS)

Shirachi, D. K.; Shirley, R. S.

1981-01-01

The effects of bandwidth differences between visual and motion cueing systems on pilot performance for a coordinated roll task were investigated. Visual and motion cue configurations which were acceptable and the effects of reduced motion cue scaling on pilot performance were studied to determine the scale reduction threshold for which pilot performance was significantly different from full scale pilot performance. It is concluded that: (1) the presence or absence of high frequency error information in the visual and/or motion display systems significantly affects pilot performance; and (2) the attenuation of motion scaling while maintaining other display dynamic characteristics constant, affects pilot performance.

A fluidized bed desorption system for recycling mercury from contaminated soil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harriss, C.; Baum, D.L. Jr.; Read, W.L.

1995-12-31

The land disposal restrictions effective for wastes containing mercury have created a need for technologies that can meet the best demonstrated available technologies (BDAT) treatment standards. In the past, technologies for mercury were in short supply. In addition to the already existing short supply, the natural gas industry has begun to remediate the numerous metering sites that have been contaminated with mercury from manometers installed along their pipelines. To meet the need for a mercury technology, Philip Environmental Services Corporation (Philip) evaluated and tested two different technologies capable of recovering mercury from contaminated soil. Philip initially performed some tests usingmore » gravitational methods followed by pilot-scale testing using a fluidized bed desorber. As a result of the testing, Philip constructed a full-scale fluidized bed system which can recover mercury from contaminated soil and debris. The name of Philip`s technology is the Solvating Vapor Pressure Process (SVPP). The main purpose of this paper is to discuss the results of the SVPP pilot testing and describe the process.« less

Use of centrifugal-gravity concentration for rejection of talc and recovery improvement in base-metal flotation

NASA Astrophysics Data System (ADS)

Klein, Bern; Altun, Naci Emre; Ghaffari, Hassan

2016-08-01

The possibility of using a centrifugal-gravity concentrator to reject Mg-bearing minerals and minimize metal losses in the flotation of base metals was evaluated. Sample characterization, batch scoping tests, pilot-scale tests, and regrind-flotation tests were conducted on a Ni flotation tailings stream. Batch tests revealed that the Mg grade decreased dramatically in the concentrate products. Pilot-scale testing of a continuous centrifugal concentrator (Knelson CVD6) on the flotation tailings revealed that a concentrate with a low mass yield, low Mg content, and high Ni upgrade ratio could be achieved. Under optimum conditions, a concentrate at 6.7% mass yield was obtained with 0.85% Ni grade at 12.9% Ni recovery and with a low Mg distribution (1.7%). Size partition curves demonstrated that the CVD also operated as a size classifier, enhancing the rejection of talc fines. Overall, the CVD was capable of rejecting Mg-bearing minerals. Moreover, an opportunity exists for the novel use of centrifugal-gravity concentration for scavenging flotation tailings and/or after comminution to minimize amount of Mg-bearing minerals reporting to flotation.

Flight Tests of a 0.13-Scale Model of the Convair XFY-1 Vertically Rising Airplane in a Setup Simulating that Proposed for Captive-Flight Tests in a Hangar, TED No. NACA DE 368

NASA Technical Reports Server (NTRS)

Lovell, Powell M., Jr.

1953-01-01

An experimental investigation has been conducted to determine the dynamic stability and control characteristics of a 0.13-scale free-flight model of the Convair XFY-1 airplane in test setups representing the setup proposed for use in the first flight tests of the full-scale airplane in the Moffett Field airship hangar. The investigation was conducted in two parts: first, tests with the model flying freely in an enclosure simulating the hangar, and second, tests with the model partially restrained by an overhead line attached to the propeller spinner and ground lines attached to the wing and tail tips. The results of the tests indicated that the airplane can be flown without difficulty in the Moffett Field airship hangar if it does not approach too close to the hangar walls. If it does approach too close to the walls, the recirculation of the propeller slipstream might cause sudden trim changes which would make smooth flight difficult for the pilot to accomplish. It appeared that the tethering system proposed by Convair could provide generally satisfactory restraint of large-amplitude motions caused by control failure or pilot error without interfering with normal flying or causing any serious instability or violent jerking motions as the tethering lines restrained the model.

FINAL REPORT SUMMARY OF DM 1200 OPERATION AT VSL VSL-06R6710-2 REV 0 9/7/06

DOE Office of Scientific and Technical Information (OSTI.GOV)

KRUGER AA; MATLACK KS; DIENER G

2011-12-29

The principal objective of this report was to summarize the testing experience on the DuraMelter 1200 (DMI200), which is the High Level Waste (HLW) Pilot Melter located at the Vitreous State Laboratory (VSL). Further objectives were to provide descriptions of the history of all modifications and maintenance, methods of operation, problems and unit failures, and melter emissions and performance while processing a variety of simulated HL W and low activity waste (LAW) feeds for the Hanford Waste Treatment and Immobilization Plant (WTP) and employing a variety of operating methods. All of these objectives were met. The River Protection Project -more » Hanford Waste Treatment and Immobilization Plant (RPP-WTP) Project has undertaken a 'tiered' approach to vitrification development testing involving computer-based glass formulation, glass property-composition models, crucible melts, and continuous melter tests of increasing, more realistic scales. Melter systems ranging from 0.02 to 1.2 m{sup 2} installed at the Vitreous State Laboratory (VSL) have been used for this purpose, which, in combination with the 3.3 m{sup 2} low activity waste (LAW) Pilot Melter at Duratek, Inc., span more than two orders of magnitude in melt surface area. In this way, less-costly small-scale tests can be used to define the most appropriate tests to be conducted at the larger scales in order to extract maximum benefit from the large-scale tests. For high level waste (HLW) vitrification development, a key component in this approach is the one-third scale DuraMelter 1200 (DM 1200), which is the HLW Pilot Melter that has been installed at VSL with an integrated prototypical off-gas treatment system. That system replaced the DM1000 system that was used for HLW throughput testing during Part B1. Both melters have similar melt surface areas (1.2 m{sup 2}) but the DM1200 is prototypical of the present RPP-WTP HLW melter design whereas the DM1000 was not. In particular, the DM1200 provides for testing on a vitrification system with the specific train of unit operations that has been selected for both HLW and LAW RPP-WTP off-gas treatment.« less

SUPERFUND TREATABILITY CLEARINGHOUSE: INCINERATION TEST OF EXPLOSIVES CONTAMINATED SOILS AT SAVANNA ARMY DEPOT ACTIVITY, SAVANNA, ILLINOIS

EPA Science Inventory

The primary objective of these tests was to demonstrate the effectiveness of incineration as a decontamination method for explosives contaminated sails. A pilot-scale rotary kiln incinerator, manufactured by ThermAll, Inc., was used to treat both sandy and clayey...

Consumer Perceptions About Pilot Training: An Emotional Response

NASA Astrophysics Data System (ADS)

Rosser, Timothy G.

Civilian pilot training has followed a traditional path for several decades. With a potential pilot shortage approaching, ICAO proposed a new paradigm in pilot training methodology called the Multi-Crew Pilot License. This new methodology puts a pilot in the cockpit of an airliner with significantly less flight time experience than the traditional methodology. The purpose of this study was to determine to what extent gender, country of origin and pilot training methodology effect an aviation consumer's willingness to fly. Additionally, this study attempted to determine what emotions mediate a consumer's decision. This study surveyed participants from India and the United States to measure their willingness to fly using the Willingness to Fly Scale shown to be valid and reliable by Rice et al. (2015). The scale uses a five point Likert-type scale. In order to determine the mediating emotions, Ekman and Friesen's (1979) universal emotions, which are happiness, surprise, fear, disgust, anger, and sadness were used. Data were analyzed using SPSS. Descriptive statistics are provided for respondent's age and willingness to fly values. An ANOVA was conducted to test the first four hypotheses and Hayes (2004, 2008) bootstrapping process was used for the mediation analysis. Results indicated a significant main effect for training, F(1,972) = 227.76, p . .001, etap 2 = 0.190, country of origin, F(1, 972) = 28.86, p < .001, .p 2 = 0.029, and a two-way interaction was indicated between training and country of origin, F(7, 972) = 46.71, p < .001, etap 2 = 0.252. Mediation analysis indicated the emotions anger, fear, happiness, and surprise mediated the relationship between training and country of origin, and training. The findings of this study are important to designers of MPL training programs and airline marketers.

Energy Evaluation of a New Construction Pilot Community: Fresno, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burdick, A.; Poerschke, A.; Rapport, A.

2014-06-01

A new construction pilot community was constructed by builder-partner Wathen-Castanos Hybrid Homes (WCHH) based on a single occupied test house that was designed to achieve greater than 30% energy savings with respect to the House Simulation Protocols (Hendron, Robert; Engebrecht, Cheryn (2010). Building America House Simulation Protocols. Golden, CO: National Renewable Energy Laboratory). Builders face several key problems when implementing a whole-house systems integrated measures package (SIMP) from a single test house into multiple houses. Although a technical solution already may have been evaluated and validated in an individual test house, the potential exists for constructability failures at the communitymore » scale. This report addresses factors of implementation and scalability at the community scale and proposes methodologies by which community-scale energy evaluations can be performed based on results at the occupied test house level. Research focused on the builder and trade implementation of a SIMP and the actual utility usage in the houses at the community scale of production. Five occupants participated in this community-scale research by providing utility bills and information on occupancy and miscellaneous gas and electric appliance use for their houses. IBACOS used these utility data and background information to analyze the actual energy performance of the houses. Verification with measured data is an important component in predictive energy modeling. The actual utility bill readings were compared to projected energy consumption using BEopt with actual weather and thermostat set points for normalization.« less

Comprehensive Evaluation of Biological Growth Control by Chlorine-Based Biocides in Power Plant Cooling Systems Using Tertiary Effluent

PubMed Central

Chien, Shih-Hsiang; Dzombak, David A.; Vidic, Radisav D.

2013-01-01

Abstract Recent studies have shown that treated municipal wastewater can be a reliable cooling water alternative to fresh water. However, elevated nutrient concentration and microbial population in wastewater lead to aggressive biological proliferation in the cooling system. Three chlorine-based biocides were evaluated for the control of biological growth in cooling systems using tertiary treated wastewater as makeup, based on their biocidal efficiency and cost-effectiveness. Optimal chemical regimens for achieving successful biological growth control were elucidated based on batch-, bench-, and pilot-scale experiments. Biocide usage and biological activity in planktonic and sessile phases were carefully monitored to understand biological growth potential and biocidal efficiency of the three disinfectants in this particular environment. Water parameters, such as temperature, cycles of concentration, and ammonia concentration in recirculating water, critically affected the biocide performance in recirculating cooling systems. Bench-scale recirculating tests were shown to adequately predict the biocide residual required for a pilot-scale cooling system. Optimal residuals needed for proper biological growth control were 1, 2–3, and 0.5–1 mg/L as Cl2 for NaOCl, preformed NH2Cl, and ClO2, respectively. Pilot-scale tests also revealed that Legionella pneumophila was absent from these cooling systems when using the disinfectants evaluated in this study. Cost analysis showed that NaOCl is the most cost-effective for controlling biological growth in power plant recirculating cooling systems using tertiary-treated wastewater as makeup. PMID:23781129

Comprehensive Evaluation of Biological Growth Control by Chlorine-Based Biocides in Power Plant Cooling Systems Using Tertiary Effluent.

PubMed

Chien, Shih-Hsiang; Dzombak, David A; Vidic, Radisav D

2013-06-01

Recent studies have shown that treated municipal wastewater can be a reliable cooling water alternative to fresh water. However, elevated nutrient concentration and microbial population in wastewater lead to aggressive biological proliferation in the cooling system. Three chlorine-based biocides were evaluated for the control of biological growth in cooling systems using tertiary treated wastewater as makeup, based on their biocidal efficiency and cost-effectiveness. Optimal chemical regimens for achieving successful biological growth control were elucidated based on batch-, bench-, and pilot-scale experiments. Biocide usage and biological activity in planktonic and sessile phases were carefully monitored to understand biological growth potential and biocidal efficiency of the three disinfectants in this particular environment. Water parameters, such as temperature, cycles of concentration, and ammonia concentration in recirculating water, critically affected the biocide performance in recirculating cooling systems. Bench-scale recirculating tests were shown to adequately predict the biocide residual required for a pilot-scale cooling system. Optimal residuals needed for proper biological growth control were 1, 2-3, and 0.5-1 mg/L as Cl 2 for NaOCl, preformed NH 2 Cl, and ClO 2 , respectively. Pilot-scale tests also revealed that Legionella pneumophila was absent from these cooling systems when using the disinfectants evaluated in this study. Cost analysis showed that NaOCl is the most cost-effective for controlling biological growth in power plant recirculating cooling systems using tertiary-treated wastewater as makeup.

Development of a measure of model fidelity for mental health Crisis Resolution Teams.

PubMed

Lloyd-Evans, Brynmor; Bond, Gary R; Ruud, Torleif; Ivanecka, Ada; Gray, Richard; Osborn, David; Nolan, Fiona; Henderson, Claire; Mason, Oliver; Goater, Nicky; Kelly, Kathleen; Ambler, Gareth; Morant, Nicola; Onyett, Steve; Lamb, Danielle; Fahmy, Sarah; Brown, Ellie; Paterson, Beth; Sweeney, Angela; Hindle, David; Fullarton, Kate; Frerichs, Johanna; Johnson, Sonia

2016-12-01

Crisis Resolution Teams (CRTs) provide short-term intensive home treatment to people experiencing mental health crisis. Trial evidence suggests CRTs can be effective at reducing hospital admissions and increasing satisfaction with acute care. When scaled up to national level however, CRT implementation and outcomes have been variable. We aimed to develop and test a fidelity scale to assess adherence to a model of best practice for CRTs, based on best available evidence. A concept mapping process was used to develop a CRT fidelity scale. Participants (n = 68) from a range of stakeholder groups prioritised and grouped statements (n = 72) about important components of the CRT model, generated from a literature review, national survey and qualitative interviews. These data were analysed using Ariadne software and the resultant cluster solution informed item selection for a CRT fidelity scale. Operational criteria and scoring anchor points were developed for each item. The CORE CRT fidelity scale was then piloted in 75 CRTs in the UK to assess the range of scores achieved and feasibility for use in a 1-day fidelity review process. Trained reviewers (n = 16) rated CRT service fidelity in a vignette exercise to test the scale's inter-rater reliability. There were high levels of agreement within and between stakeholder groups regarding the most important components of the CRT model. A 39-item measure of CRT model fidelity was developed. Piloting indicated that the scale was feasible for use to assess CRT model fidelity and had good face validity. The wide range of item scores and total scores across CRT services in the pilot demonstrate the measure can distinguish lower and higher fidelity services. Moderately good inter-rater reliability was found, with an estimated correlation between individual ratings of 0.65 (95% CI: 0.54 to 0.76). The CORE CRT Fidelity Scale has been developed through a rigorous and systematic process. Promising initial testing indicates its value in assessing adherence to a model of CRT best practice and to support service improvement monitoring and planning. Further research is required to establish its psychometric properties and international applicability.

The effects of workload on respiratory variables in simulated flight: a preliminary study.

PubMed

Karavidas, Maria Katsamanis; Lehrer, Paul M; Lu, Shou-En; Vaschillo, Evgeny; Vaschillo, Bronya; Cheng, Andrew

2010-04-01

In this pilot study, we investigated respiratory activity and end-tidal carbon dioxide (P(et)CO(2)) during exposure to varying levels of work load in a simulated flight environment. Seven pilots (age: 34-60) participated in a one-session test on the Boeing 737-800 simulator. Physiological data were collected while pilots wore an ambulatory multi-channel recording device. Respiratory variables, including inductance plethysmography (respiratory pattern) and pressure of end-tidal carbon dioxide (P(et)CO(2)), were collected demonstrating change in CO(2) levels proportional to changes in flight task workload. Pilots performed a set of simulation flight tasks. Pilot performance was rated for each task by a test pilot; and self-report of workload was taken using the NASA-TLX scale. Mixed model analysis revealed that respiration rate and minute ventilation are significantly associated with workload levels and evaluator scores controlling for "vanilla baseline" condition. Hypocapnia exclusively occurred in tasks where pilots performed more poorly. This study was designed as a preliminary investigation in order to develop a psychophysiological assessment methodology, rather than to offer conclusive findings. The results show that the respiratory system is very reactive to high workload conditions in aviation and suggest that hypocapnia may pose a flight safety risk under some circumstances. Copyright © 2010 Elsevier B.V. All rights reserved.

Validation and Exploration of Instruments for Assessing Public Knowledge of and Attitudes toward Nanotechnology

ERIC Educational Resources Information Center

Lin, Shu-Fen; Lin, Huann-shyang; Wu, Yi-ying

2013-01-01

The purposes of this study were to develop instruments that assess public knowledge of nanotechnology (PKNT), public attitudes toward nanotechnology (PANT) and conduct a pilot study for exploring the relationship between PKNT and PANT. The PKNT test was composed of six scales involving major nanotechnology concepts, including size and scale,…

Validity and reliability of a pilot scale for assessment of multiple system atrophy symptoms.

PubMed

Matsushima, Masaaki; Yabe, Ichiro; Takahashi, Ikuko; Hirotani, Makoto; Kano, Takahiro; Horiuchi, Kazuhiro; Houzen, Hideki; Sasaki, Hidenao

2017-01-01

Multiple system atrophy (MSA) is a rare progressive neurodegenerative disorder for which brief yet sensitive scale is required in order for use in clinical trials and general screening. We previously compared several scales for the assessment of MSA symptoms and devised an eight-item pilot scale with large standardized response mean [handwriting, finger taps, transfers, standing with feet together, turning trunk, turning 360°, gait, body sway]. The aim of the present study is to investigate the validity and reliability of a simple pilot scale for assessment of multiple system atrophy symptoms. Thirty-two patients with MSA (15 male/17 female; 20 cerebellar subtype [MSA-C]/12 parkinsonian subtype [MSA-P]) were prospectively registered between January 1, 2014 and February 28, 2015. Patients were evaluated by two independent raters using the Unified MSA Rating Scale (UMSARS), Scale for Assessment and Rating of Ataxia (SARA), and the pilot scale. Correlations between UMSARS, SARA, pilot scale scores, intraclass correlation coefficients (ICCs), and Cronbach's alpha coefficients were calculated. Pilot scale scores significantly correlated with scores for UMSARS Parts I, II, and IV as well as with SARA scores. Intra-rater and inter-rater ICCs and Cronbach's alpha coefficients remained high (> 0.94) for all measures. The results of the present study indicate the validity and reliability of the eight-item pilot scale, particularly for the assessment of symptoms in patients with early state multiple system atrophy.

Pilot-scale electrokinetic movement of HCB and Zn in real contaminated sediments enhanced with hydroxypropyl-beta-cyclodextrin.

PubMed

Li, Taiping; Yuan, Songhu; Wan, Jinzhong; Lin, Li; Long, Huayun; Wu, Xiaofeng; Lu, Xiaohua

2009-08-01

This study deals with the efficiency of a pilot-scale electrokinetic (EK) treatment on real aged sediments contaminated with hexachlorobenzene (HCB) and Zn. A total of 0.5m(3) of sediments were treated under a constant voltage in a polyvinyl chloride reactor. The changes of sediment pH, electrical conductivity (EC), organic content (OC), the transport of contaminants in sediments and the consumption of electric energy were evaluated. After 100 d processing, sediment pH slightly increased compared with the initial values, particularly in the bottom layer close to cathodic section, while sediment EC in most sections significantly decreased. Sediment OC in all sections increased, which implied that hydroxypropyl-beta-cyclodextrin (HPCD) was successfully penetrated across sediments by electroosmosis. Significant movement of contaminants was observed across sediments with negligible removals. Both HCB and Zn generally moved from sections near anode and accumulated near cathode. Upon the completion of treatment, the electric energy consumption was calculated as 563 kWhm(-3). This pilot-scale EK test indicates that it is difficult to achieve great removal of hydrophobic organic compounds (HOCs), or HOCs and heavy metal mixed contaminants, by EK treatment in large scale with the use of HPCD.

Free-Spinning-Tunnel Tests of a 1/24-Scale Model of the Grumman XF9F-2 Airplane, TED No. NACA DE 317

NASA Technical Reports Server (NTRS)

Berman, Theodore

1948-01-01

An investigation of the spin and recovery characteristics of a scale model of the Grumman XF9F-2 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect and inverted spin and recovery characteristics of the model in the flight loading were determined. The investigation also included spin-recovery-parachute, pilot-escape, and rudder-pedal- . force tests. The recovery characteristics of the model were satisfactory for all configurations tested. Spins for the normal control configuration were oscillatory in roll and yaw. Deflecting the leading-edge flaps or the dive brakes did not change the spin and recovery characteristics of the model noticeably. A 10.0-foot tail parachute or a 6.0-foot wing-tip parachute (drag coefficient of 0.75) was found to be effective for recoveries from demonstration spins. The rudder forces in the spin appeared to be within the capabilities of the pilot.

Effects of a multidisciplinary group rehabilitation programme on participation of the visually impaired elderly: a pilot study.

PubMed

Alma, Manna A; Groothoff, Johan W; Melis-Dankers, Bart J M; Post, Marcel W M; Suurmeijer, Theo P B M; van der Mei, Sijrike F

2012-01-01

To pilot test the newly developed multidisciplinary group rehabilitation programme Visually Impaired elderly Persons Participating (VIPP). A single group pretest-posttest design pilot study included 29 visually impaired persons (≥ 55 years). The intervention (20 weekly meetings) consisted of four components (practical training; education, social interaction, counselling and training of problem-solving skills; individual and group goal setting; home-based exercise programme). Participation was assessed with the Utrecht Scale for Evaluation of Rehabilitation-Participation (USER-P) and the Impact on Participation and Autonomy (IPA) questionnaire at baseline, immediately and 6 months after the intervention. At scale level, no statistical significant changes over time were found whereas the effect size indicated small effects for restrictions and satisfaction with participation, and a medium effect for autonomy outdoors. At item level, improvements tended to occur in frequency of housekeeping, in restrictions in housekeeping and outdoor activities and in satisfaction with the partner relationship. Satisfaction with leisure indoors and autonomy regarding using leisure time tended to increase as well. The tentative conclusion of this small-scale pilot study is that the VIPP programme modestly benefits perceived restrictions in participation, satisfaction with participation and autonomy outdoors of the visually impaired elderly. These preliminary findings warrant further investigation.

Development and demonstration of a lignite-pelletizing process. Phase II report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-01-01

The current work began with scale-up of laboratory equipment to commercial size equipment. For this purpose, BCI used an existing pilot plant that had been assembled to pelletize and indurate taconite ore. BCI determined therewith that lignite pellets can be produced continuously on a pilot scale using the basic process developed in the laboratory. The resulting pellets were found to be similar to the laboratory pellets at equivalent binder compositions. Tests of product made during a 5-ton test run are reported. A 50-ton demonstration test run was made with the pilot plant. Pellet production was sustained for a two-week period.more » The lignite pelletizing process has, therefore, been developed to the point of demonstration in a 50-ton test. BCI has completed and cost estimated a conceptually designed 4000 TPD facility. BCI believes it has demonstrated a technically feasible process to agglomerate lignite by using an asphalt emulsion binder. Product quality is promising. Capital and operating costs appear acceptable to justify continuing support and development. The next step should focus on three areas: production development, process refinement, and cost reduction. For further development, BCI recommends consideration of a 5 to 10 ton/h pilot plant or a 20 to 40 ton/h module of a full sized plant, the lower first cost of the former being offset by the ability to incorporate the latter into a future production unit. Other specific recommendations are made for future study that could lead to process and cost improvements: Binder Formulation, disc Sizing, Drier Bed Depth, and Mixing Approach. Pellet use other than power plant fuel is considered.« less

FIELD TEST OF CYCLODEXTRIN FOR ENHANCED IN-SITU FLUSHING OF MULTIPLE-COMPONENT IMMISCIBLE ORGANIC LIQUID CONTAMINATION: PROJECT OVERVIEW AND INITIAL RESULTS

EPA Science Inventory

The purpose of this paper is to present an overview and the initial results of a pilot-scale experiment designated to test the use of cyclodextrin for enhanced in-situ flushing of an aquifer contaminated by immiscible liquid. This is the first field test of this technology, terme...

Demonstration of Multifunctional DNBM Corrosion Inhibitors in Protective Coatings for Naval Air/Weapon Systems

DTIC Science & Technology

1993-12-01

Evaluation of Increased Payloads 6 3.2 Microencapsulation Scale-up of Pilot DNBM 10 4 SURFACE TREATMENT OF MICROCAPSULES 11 4.1 Fumed Silica Additions to... Microencapsulated DNBM b. Fumed-Silica Mixed Microcapsules C. Solvent-Extracted Silanized Microcapsules Fig. 8 SEM Photomicrographs of Pilot-DNBM... Microcapsules 18 NAWCADWAR-94128-60 Section 5 FORMULATION AND TEST OF 100% DNBM AND MICROENCAPSULATED DNBM IN EPOXY-POLYAMIDE PRIMER At the start of the

Summary of flight tests to determine the spin and controllability characteristics of a remotely piloted, large-scale (3/8) fighter airplane model

NASA Technical Reports Server (NTRS)

Holleman, E. C.

1976-01-01

An unpowered, large, dynamically scaled airplane model was test flown by remote pilot to investigate the stability and controllability of the configuration at high angles of attack. The configuration proved to be departure/spin resistant; however, spins were obtained by using techniques developed on a flight support simulator. Spin modes at high and medium high angles of attack were identified, and recovery techniques were investigated. A flight support simulation of the airplane model mechanized with low speed wind tunnel data over an angle of attack range of + or - 90 deg. and an angle of sideslip range of + or - 40 deg. provided insight into the effects of altitude, stability, aerodynamic damping, and the operation of the augmented flight control system on spins. Aerodynamic derivatives determined from flight maneuvers were used to correlate model controllability with two proposed departure/spin design criteria.

PILOT-SCALE INCINERATION TESTING OF FLUFF AND SOIL FROM THE M.W. MANUFACTURING SUPERFUND SITE

EPA Science Inventory

A series of six tests was performed on wastes (fluff and contaminated soil) from the M.W. Manufacturing Superfund Site to determine the efficacy of incineration as the proposed remediation technology. he fluff, which is the insulation from scrap wire, and the soil wastes are cont...

REDUCTION OF GENOTOXICITY OF A CREOSOTE-CONTAMINATED SOIL AFTER FUNGAL TREATMENT DETERMINED BY THE TRADESCANTIA-MICRONUCLEUS TEST

EPA Science Inventory

The fungal degradation of polyaromatic hydrocarbons (PAH) in a contaminated soil from a hazarous waste site was evaluated in a pilot-scale study. As some PAH are known to be mutagens, the Tradescantia-micronucleus test (TRAD-MCN) was selected to evaluate the genotoxicity of the s...

Carbon Mineralization by Aqueous Precipitation for Beneficial Use of CO2 from Flue Gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Devenney, Martin; Gilliam, Ryan; Seeker, Randy

2013-08-01

The objective of this project is to demonstrate an innovative process to mineralize CO2 from flue gas directly to reactive carbonates and maximize the value and versatility of its beneficial use products. The program scope includes the design, construction, and testing of a CO2 Conversion to Material Products (CCMP) Pilot Demonstration Plant utilizing CO2 from the flue gas of a power production facility in Moss Landing, CA. This topical report covers Subphase 2a which is the design phase of pilot demonstration subsystems. Materials of construction have been selected and proven in both lab scale and prototype testing to be acceptablemore » for the reagent conditions of interest. The target application for the reactive carbonate material has been selected based upon small-scale feasibility studies and the design of a continuous fiber board production line has been completed. The electrochemical cell architecture and components have been selected based upon both lab scale and prototype testing. The appropriate quality control and diagnostic techniques have been developed and tested along with the required instrumentation and controls. Finally the demonstrate site infrastructure, NEPA categorical exclusion, and permitting is all ready for the construction and installation of the new units and upgrades.« less

Pilot study of a targeted dance class for physical rehabilitation in children with cerebral palsy

PubMed Central

López-Ortiz, Citlali; Egan, Tara; Gaebler-Spira, Deborah J

2016-01-01

Introduction: This pilot study evaluates the effects of a targeted dance class utilizing classical ballet principles for rehabilitation of children with cerebral palsy on balance and upper extremity control. Methods: Twelve children with cerebral palsy (ages 7–15 years) with Gross Motor Function Classification scores II–IV participated in this study and were assigned to either a control group or targeted dance class group. Targeted dance class group participated in 1-h classes three times per week in a 4-week period. The Pediatric Balance Scale and the Quality of Upper Extremity Skills Test were administered before, after, and 1 month after the targeted dance class. Results: Improvements in the Pediatric Balance Scale were present in the targeted dance class group in before versus after and before versus 1 month follow-up comparisons (p-value = 0.0088 and p-value = 0.019, respectively). The Pediatric Balance Scale changes were not significant in the control group. The Quality of Upper Extremity Skills Test did not reach statistical differences in either group. Conclusion: Classical ballet as an art form involves physical training, musical accompaniment, social interactions, and emotional expression that could serve as adjunct to traditional physical therapy. This pilot study demonstrated improvements in balance control. A larger study with a more homogeneous sample is warranted. PMID:27721977

Designing for Scale: Reflections on Rolling Out Reading Improvement in Kenya and Liberia.

PubMed

Gove, Amber; Korda Poole, Medina; Piper, Benjamin

2017-03-01

Since 2008, the Ministries of Education in Liberia and Kenya have undertaken transitions from small-scale pilot programs to improve reading outcomes among primary learners to the large-scale implementation of reading interventions. The effects of the pilots on learning outcomes were significant, but questions remained regarding whether such large gains could be sustained at scale. In this article, the authors dissect the Liberian and Kenyan experiences with implementing large-scale reading programs, documenting the critical components and conditions of the program designs that affected the likelihood of successfully transitioning from pilot to scale. They also review the design, deployment, and effectiveness of each pilot program and the scale, design, duration, enabling conditions, and initial effectiveness results of the scaled programs in each country. The implications of these results for the design of both pilot and large-scale reading programs are discussed in light of the experiences of both the Liberian and Kenyan programs. © 2017 Wiley Periodicals, Inc.

Chronic care coordination by integrating care through a team-based, population-driven approach: a case study.

PubMed

van Eeghen, Constance O; Littenberg, Benjamin; Kessler, Rodger

2018-05-23

Patients with chronic conditions frequently experience behavioral comorbidities to which primary care cannot easily respond. This study observed a Vermont family medicine practice with integrated medical and behavioral health services that use a structured approach to implement a chronic care management system with Lean. The practice chose to pilot a population-based approach to improve outcomes for patients with poorly controlled Type 2 diabetes using a stepped-care model with an interprofessional team including a community health nurse. This case study observed the team's use of Lean, with which it designed and piloted a clinical algorithm composed of patient self-assessment, endorsement of behavioral goals, shared documentation of goals and plans, and follow-up. The team redesigned workflows and measured reach (patients who engaged to the end of the pilot), outcomes (HbA1c results), and process (days between HbA1c tests). The researchers evaluated practice member self-reports about the use of Lean and facilitators and barriers to move from pilot to larger scale applications. Of 20 eligible patients recruited over 3 months, 10 agreed to participate and 9 engaged fully (45%); 106 patients were controls. Relative to controls, outcomes and process measures improved but lacked significance. Practice members identified barriers that prevented implementation of all changes needed but were in agreement that the pilot produced useful outcomes. A systematized, population-based, chronic care management service is feasible in a busy primary care practice. To test at scale, practice leadership will need to allocate staffing, invest in shared documentation, and standardize workflows to streamline office practice responsibilities.

Sequential Design of Experiments to Maximize Learning from Carbon Capture Pilot Plant Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soepyan, Frits B.; Morgan, Joshua C.; Omell, Benjamin P.

Pilot plant test campaigns can be expensive and time-consuming. Therefore, it is of interest to maximize the amount of learning and the efficiency of the test campaign given the limited number of experiments that can be conducted. This work investigates the use of sequential design of experiments (SDOE) to overcome these challenges by demonstrating its usefulness for a recent solvent-based CO2 capture plant test campaign. Unlike traditional design of experiments methods, SDOE regularly uses information from ongoing experiments to determine the optimum locations in the design space for subsequent runs within the same experiment. However, there are challenges that needmore » to be addressed, including reducing the high computational burden to efficiently update the model, and the need to incorporate the methodology into a computational tool. We address these challenges by applying SDOE in combination with a software tool, the Framework for Optimization, Quantification of Uncertainty and Surrogates (FOQUS) (Miller et al., 2014a, 2016, 2017). The results of applying SDOE on a pilot plant test campaign for CO2 capture suggests that relative to traditional design of experiments methods, SDOE can more effectively reduce the uncertainty of the model, thus decreasing technical risk. Future work includes integrating SDOE into FOQUS and using SDOE to support additional large-scale pilot plant test campaigns.« less

Field Testing of Cryogenic Carbon Capture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sayre, Aaron; Frankman, Dave; Baxter, Andrew

Sustainable Energy Solutions has been developing Cryogenic Carbon Capture™ (CCC) since 2008. In that time two processes have been developed, the External Cooling Loop and Compressed Flue Gas Cryogenic Carbon Capture processes (CCC ECL™ and CCC CFG™ respectively). The CCC ECL™ process has been scaled up to a 1TPD CO2 system. In this process the flue gas is cooled by an external refrigerant loop. SES has tested CCC ECL™ on real flue gas slip streams from subbituminous coal, bituminous coal, biomass, natural gas, shredded tires, and municipal waste fuels at field sites that include utility power stations, heating plants, cementmore » kilns, and pilot-scale research reactors. The CO2 concentrations from these tests ranged from 5 to 22% on a dry basis. CO2 capture ranged from 95-99+% during these tests. Several other condensable species were also captured including NO2, SO2 and PMxx at 95+%. NO was also captured at a modest rate. The CCC CFG™ process has been scaled up to a .25 ton per day system. This system has been tested on real flue gas streams including subbituminous coal, bituminous coal and natural gas at field sites that include utility power stations, heating plants, and pilot-scale research reactors. CO2 concentrations for these tests ranged from 5 to 15% on a dry basis. CO2 capture ranged from 95-99+% during these tests. Several other condensable species were also captured including NO2, SO2 and PMxx at 95+%. NO was also captured at 90+%. Hg capture was also verified and the resulting effluent from CCC CFG™ was below a 1ppt concentration. This paper will focus on discussion of the capabilities of CCC, the results of field testing and the future steps surrounding the development of this technology.« less

Evaluation of new chlorhexidine- and cetylpyridinium chloride-based mouthrinse formulations adjunctive to scaling and root planing: pilot study.

PubMed

García-Gargallo, M; Zurlohe, M; Montero, E; Alonso, B; Serrano, J; Sanz, M; Herrera, D

2017-11-01

To compare the effect of two newly formulated chlorhexidine (CHX) and cetylpyridinium chloride (CPC) mouthrinses after scaling and root planing (SRP) in terms of clinical, microbiological, patient-based variables and adverse events, with a positive control with the same active components, already marketed and tested. A pilot, randomized clinical trial, double-blind, parallel design with 1-month follow-up was conducted. Chronic periodontitis patients requiring non-surgical periodontal therapy were enrolled and randomly assigned to: (i) SRP and test-1 (new reformulation: 0.12% CHX and 0.05% CPC); (ii) SRP and test-2 (new formulation: 0.03% CHX and 0.05% CPC); or (iii) SRP and positive control (commercial product: 0.12% CHX and 0.05% CPC). All variables were evaluated at baseline and 1 month after SRP. Quantitative variables were compared by means of anova or Kruskal-Wallis test and qualitative variables by chi-square or McNemar tests. Thirty patients (10 per group) were included. After 1 month, there were significant differences among groups in plaque levels (P = 0.016) as test-1 showed less sites with plaque than test-2 (31.15% [standard error-SE 2.21%] versus 49.39% [SE 4.60%), respectively). No significant differences were found for global patient perception of the product or in adverse effects. Test groups showed better results in levels and proportions (P = 0.022) of Capnocytophaga spp. Within the limitations of this pilot study, it can be concluded that the newly formulated 0.12% CHX and 0.05% CPC mouthrinse showed larger plaque level reductions, without showing more adverse effects, when compared to the other two mouthrinses, after SRP. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Pilot Study: Survey Tools for Assessing Parenting Styles and Family Contributors to the Development of Obesity in Arab Children Ages 6 to 12 Years.

PubMed

Tami, Suzan H; Reed, Debra B; Trejos, Elizabeth; Boylan, Mallory; Wang, Shu

2015-11-05

Our pilot study was conducted to test the reliability of the Caregiver's Feeding Styles Questionnaire (CFSQ) and the Family Nutrition and Physical Activity Assessment (FNPA) in a sample of Arab mothers. Twenty-five Arab mothers completed the CFSQ, FNPA, and the Participant Background Survey for the first administration. After 1-2 weeks, participants completed the CFSQ and the FNPA for the second administration. The two administrations of the surveys allowed for test/retest reliability of the CFSQ and the FNPA and to measure the internal consistency of the two surveys. Pearson's correlation between the first and second administrations or the 19-item scale (demandingness) and the 7-item scale (responsiveness) of the CFSQ were .95 and .86, respectively. As for the FNPA, Pearson's correlation was .80. The estimated reliabilities (Cronbach's alpha) of the CFSQ increased from .86 for the first administration to .93 for the second administration. However, the estimated reliabilities of the FNPA slightly increased from .58 for first administration to .59 for the second administration. In our pilot study of Arab mothers, the CFSQ and FNPA were shown to be promising in terms of reliability and content validity.

Ultra Barrier Topsheet Film for Flexible Photovoltaics with 3M Company

DOE Office of Scientific and Technical Information (OSTI.GOV)

Funkenbusch, Arnie; Ruth, Charles

2014-12-30

In this DOE sponsored program, 3M achieved the critical UBT features to enable durable flexible high efficiency modules to be produced by a range of customers who have now certified the 3M UBT and are actively developing said flexible modules. The specific objectives and accomplishments of the work under this program were; Scale-up the current Generation-1 UBT from 12” width, as made on 3M’s pilot line, to 1+meter width full-scale manufacturing, while maintaining baseline performance metrics (see table below); This objective was fully met; Validate service life of Generation-1 UBT for the 25+ year lifetime demanded by the photovoltaic market;more » Aggressive testing revealed potential failure modes in the Gen 1 UBT. Deficiencies were identified and corrective action taken in the Gen 2 UBT; Develop a Generation-2 UBT on the pilot line, targeting improved performance relative to baseline, including higher %T (percent transmission), lower water vapor transmission rate (WVTR) with targets based on what the technology needs for 25 year lifetime, proven lifetime of 25 years in solar module construction in the field, and lower cost; Testing of UBT Gen 2 under a wide range of conditions presented in this report failed to reveal any failure mode. Therefore UBT Gen 2 is known to be highly durable. 3M will continue to test towards statistically validating a 25 year lifetime under 3M funding; Transfer Generation-2 UBT from the pilot line to the full-scale manufacturing line within three years; and This objective was fully met.« less

Large-scale thermal storage systems. Possibilities of operation and state of the art

NASA Astrophysics Data System (ADS)

Jank, R.

1983-05-01

The state of the art of large scale thermal energy storage concepts is reviewed. With earth pit storage, the materials question has to be concentrated on. The use of container storage in conventional long distance thermal nets has to be stimulated. Aquifer storage should be tested in a pilot plant to obtain experience in natural aquifer use.

Development of Physics Attitude Scale (PAS): An Instrument to Measure Students' Attitudes toward Physics

ERIC Educational Resources Information Center

Kaur, Daisy; Zhao, Yi

2017-01-01

The present study is focused on the detailed description of Physics Attitude Scale (PAS) to measure students' attitudes toward physics. The development of this new instrument involved extensive interviews with both the experts as well as the students. This was followed by expert reviews and pilot testing of the instrument. The duly revised draft…

Pilot-scale test for electron beam purification of flue gas from coal-combustion boiler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hashimoto, Shoji; Namba, Hideki; Tokunaga, Okihiro

1995-06-01

Construction of a pilot plant of the treatment capacity of 12,000 m{sup 3}N/h flue gas was completed in November, 1992 in the Shin-Nagoya Thermal Power Station, Nagoya for electron beam purification of flue-gas from coal combustion boiler and the operation had been continued during one year. The results obtained In the tests shows that the target removal efficiency for SO{sub 2} (94 %) and for NO{sub x} (80 %) was achieved with appropriate operation conditions (electron beam dose, temperature, amount of ammonia etc.). The effective collection of powdery by-products was performed by an electrostatic precipitator.

APPLIED MERCURY CAPTURE

EPA Science Inventory

The first purpose of this project is to complete bench and pilot scale testing of promising mercury sorbents. This work would apply findings from fundamental, mechanistic efforts over the past three years that have developed sorbents which show improved capture of elemental and ...

CRYPTOSPORIDIUM INACTIVATION AND REMOVAL RESEARCH

EPA Science Inventory

Bench- and pilot-scale tests were performed to assess the ability of conventional treatment, ozonation and chlorine dioxide to remove and inactivate Cryptosporidium oocysts. The impacts of coagulant type, coagulant dose, raw water quality, filter loading rates and filter media w...

[The linear dimensions of human body measurements of Chinese male pilots in standing posture].

PubMed

Guo, Xiao-chao; Liu, Bao-shan; Xiao, Hui; Wang, Zhi-jie; Li, Rong; Guo, Hui

2003-02-01

To provide the latest anthropometric data of Chinese male pilots on a large scale. 94 linear dimensions of human body measurements were defined, of which there are 42 fundamental items and 52 recommended items. The computer databanks were programmed, in which the subprograms were preset for data checking such as extreme value examination, logical judgement for data relationship, and measuring-remeasuring difference test. All workers were well trained before pilot measurements. 1739 male pilots from China Air Force was measured for the 42 fundamental items, and of which 904 pilots were measured for the 52 recommended items. Mean, standard deviation, the maximum value, the minimal value, and the 5th, 50th, 95th percentile data of all the 94 items were given. The quality of the data was stable and reliable. All data of the 94 linear dimensions of human body measurements were valid and reliable with high precision.

F-8 SCW on ramp with test pilot Tom McMurtry

NASA Image and Video Library

1972-12-20

A Vought F-8A Crusader was selected by NASA as the testbed aircraft (designated TF-8A) to install an experimental Supercritical Wing (SCW) in place of the conventional wing. The unique design of the Supercritical Wing reduces the effect of shock waves on the upper surface near Mach 1, which in turn reduces drag. In this photograph the TF-8A Crusader with Supercritical Wing is shown on the ramp with project pilot Tom McMurtry standing beside it. McMurtry received NASA's Exceptional Service Medal for his work on the F-8 SCW aircraft. He also flew the AD-1, F-15 Digital Electronic Engine Control, the KC-130 winglets, the F-8 Digital Fly-By-Wire and other flight research aircraft including the remotely piloted 720 Controlled Impact Demonstration and sub-scale F-15 research projects. In addition, McMurtry was the 747 co-pilot for the Shuttle Approach and Landing Tests and made the last glide flight in the X-24B. McMurtry was Dryden’s Director for Flight Operations from 1986 to 1998, when he became Associate Director for Operations at NASA Dryden. In 1982, McMurtry received the Iven C. Kincheloe Award from the Society of Experimental Test Pilots for his contributions as project pilot on the AD-1 Oblique Wing program. In 1998 he was named as one of the honorees at the Lancaster, Calif., ninth Aerospace Walk of Honor ceremonies. In 1999 he was awarded the NASA Distinguished Service Medal. He retired in 1999 after a distinguished career as pilot and manager at Dryden that began in 1967.

Transport pilot workload - A comparison of two subjective techniques

NASA Technical Reports Server (NTRS)

Battiste, Vernol; Bortolussi, Michael

1988-01-01

Although SWAT and NASA-TLX workload scales have been compared on numerous occasions, they have not been compared in the context of transport operations. Transport pilot workload has traditionally been classified as long periods of low workload with occasional spikes of high workload. Thus, the relative sensitivity of the scales to variations in workload at the low end of the scale were evaluated. This study was a part of a larger study which investigated workload measures for aircraft certification, conducted in a Phase II certified Link/Boeing 727 simulator. No significant main effects were found for any performance-based measures of workload. However, both SWAT and NASA-TLX were sensitive to differences between high and low workload flights and to differences among flight segments. NASA-TLX (but not SWAT) was sensitive to the increase in workload during the cruise segment of the high workload flight. Between-subject variability was high for SWAT. NASA-TLX was found to be stable when compared in the test/retest paradigm. A test/retest by segment interaction suggested that this was not the case for SWAT ratings.

Psychometric properties of the Chinese-version Quality of Nursing Work Life Scale.

PubMed

Lee, Ya-Wen; Dai, Yu-Tzu; McCreary, Linda L; Yao, Grace; Brooks, Beth A

2014-09-01

In this study, we developed and tested the psychometric properties of the Chinese-version Quality of Nursing Work Life Scale along seven subscales: supportive milieu with security and professional recognition, work arrangement and workload, work/home life balance, head nurse's/supervisor's management style, teamwork and communication, nursing staffing and patient care, and milieu of respect and autonomy. An instrument-development procedure with three phases was conducted in seven hospitals in 2010-2011. Phase I comprised translation and the cultural-adaptation process, phase II comprised a pilot study, and phase III comprised a field-testing process. Purposive sampling was used in the pilot study (n = 150) and the large field study (n = 1254). Five new items were added, and 85.7% of the original items were retained in the 41 item Chinese version. Principal component analysis revealed that a model accounted for 56.6% of the variance with acceptable internal consistency, concurrent validity, and discriminant validity. This study gave evidence of reliability and validity of the 41 item Chinese-version Quality of Nursing Work Life Scale. © 2014 Wiley Publishing Asia Pty Ltd.

Pilot-Scale Test of Dephosphorization in Steelmaking Using Red Mud-Based Flux

NASA Astrophysics Data System (ADS)

Li, Fengshan; Zhang, Yanling; Guo, Zhancheng

2017-09-01

Bayer red mud is characterized by its highly oxidizing nature and high alkalinity. It can act as an ideal flux and dephosphorizer in steelmaking. In this study, pilot-scale tests applying the Bayer red mud-based flux in steelmaking have been conducted in a 200-kg, medium-frequency induction furnace. Good slag fluidity and no rephosphorization phenomena are observed. High dephosphorization rates ( 90%) and low final [P] (<0.02%) are obtained in the situation of high [C] of 2.0-3.0%, which are of great importance for the production of clean steel. The P2O5 content in the P-rich phase in the red mud-based slag can reach as high as 34.05 wt.%, far higher than the 6.73 wt.% in ordinary industrial slag. This suggests that the Al2O3, TiO2 in Bayer red mud can enhance the solid solubility of phosphorus in the P-rich phase. The data obtained are important for promoting the large-scale application of red mud in steelmaking.

Specifically Designed Constructed Wetlands: A Novel Treatment Approach for Scrubber Wastewater

DOE Office of Scientific and Technical Information (OSTI.GOV)

John H. Rodgers Jr; James W. Castle; Chris Arrington: Derek Eggert

2005-09-01

A pilot-scale wetland treatment system was specifically designed and constructed at Clemson University to evaluate removal of mercury, selenium, and other constituents from flue gas desulfurization (FGD) wastewater. Specific objectives of this research were: (1) to measure performance of a pilot-scale constructed wetland treatment system in terms of decreases in targeted constituents (Hg, Se and As) in the FGD wastewater from inflow to outflow; (2) to determine how the observed performance is achieved (both reactions and rates); and (3) to measure performance in terms of decreased bioavailability of these elements (i.e. toxicity of sediments in constructed wetlands and toxicity ofmore » outflow waters from the treatment system). Performance of the pilot-scale constructed wetland treatment systems was assessed using two criteria: anticipated NPDES permit levels and toxicity evaluations using two sentinel toxicity-testing organisms (Ceriodaphnia dubia and Pimephales promelas). These systems performed efficiently with varied inflow simulations of FGD wastewaters removing As, Hg, and Se concentrations below NPDES permit levels and reducing the toxicity of simulated FGD wastewater after treatment with the constructed wetland treatment systems. Sequential extraction procedures indicated that these elements (As, Hg, and Se) were bound to residual phases within sediments of these systems, which should limit their bioavailability to aquatic biota. Sediments collected from constructed wetland treatment systems were tested to observe toxicity to Hyalella azteca or Chironomus tetans. Complete survival (100%) was observed for H. azteca in all cells of the constructed wetland treatment system and C. tentans had an average of 91% survival over the three treatment cells containing sediments. Survival and growth of H. azteca and C. tentans did not differ significantly between sediments from the constructed wetland treatment system and controls. Since the sediments of the constructed wetland treatment system are repositories for As, Hg, and Se and the bioavailability of these elements decreased after deposition, the pilot-scale constructed wetland treatment system contributed significantly to mitigation of risks to aquatic life from these elements.« less

Pilot plant operation of a nonadiabatic methanation reactor. [15 refs. ; Raney nickel catalyst

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schehl, R.R.; Pennline, H.W.; Strakey, J.P.

The design and operation of a pilot plant scale hybrid methanation reactor is discussed. The hybrid methanator, utilizing a finned, Raney nickel coated insert, consolidates features of the tube-wall and hot-gas-recycle methanation reactors. Data are presented from four tests lasting from 3/sup 1///sub 2/ weeks to three months. Topics discussed include conversion, product yields, catalyst properties, and reactor temperature profiles. A one-dimensional mathematical model capable of explaining reactor performance trends is employed.

Coupling solar photo-Fenton and biotreatment at industrial scale: main results of a demonstration plant.

PubMed

Malato, Sixto; Blanco, Julián; Maldonado, Manuel I; Oller, Isabel; Gernjak, Wolfgang; Pérez-Estrada, Leonidas

2007-07-31

This paper reports on the combined solar photo-Fenton/biological treatment of an industrial effluent (initial total organic carbon, TOC, around 500mgL(-1)) containing a non-biodegradable organic substance (alpha-methylphenylglycine at 500mgL(-1)), focusing on pilot plant tests performed for design of an industrial plant, the design itself and the plant layout. Pilot plant tests have demonstrated that biodegradability enhancement is closely related to disappearance of the parent compound, for which a certain illumination time and hydrogen peroxide consumption are required, working at pH 2.8 and adding Fe(2+)=20mgL(-1). Based on pilot plant results, an industrial plant with 100m(2) of CPC collectors for a 250L/h treatment capacity has been designed. The solar system discharges the wastewater (WW) pre-treated by photo-Fenton into a biotreatment based on an immobilized biomass reactor. First, results of the industrial plant are also presented, demonstrating that it is able to treat up to 500Lh(-1) at an average solar ultraviolet radiation of 22.9Wm(-2), under the same conditions (pH, hydrogen peroxide consumption) tested in the pilot plant.

Assessing communication skills of clinical call handlers working at an out-of-hours centre: development of the RICE rating scale.

PubMed

Derkx, Hay P; Rethans, Jan-Joost E; Knottnerus, J André; Ram, Paul M

2007-05-01

Out-of-hours centres provide telephone support to patients with medical problems. In most of these centres specially-trained nurses handle incoming telephone calls. They assess patients' needs, the degree of urgency, and determine the level of care required. Assessment of the medical problem and the quality of 'care-by-phone' depend on the medical and communication skills of the call handlers. To develop a valid, reliable, and practical rating scale to evaluate the communication skills of call handlers working at an out-of-hours centre and to improve quality of communication. Qualitative study with focus groups followed by validation of the rating scale and measurement of reliability (internal consistency). Out-of-hours centres in the Netherlands. A focus group developed the rating scale. Experts with experience in training and evaluating communication skills of medical students and GPs commented on the scale to ensure content validity. The reliability of the rating scale was tested in a pilot in which ten specially-trained assessors scored six telephone calls each. The scale, known as the RICE rating scale, has 17 items divided over four different phases of the telephone consultation: Reason for calling; Information gathering; Conclusion; and Evaluation (RICE). Content validity of the scale was assessed by two experts. Reliability of the scale tested in the pilot was 0.73 (Cronbach's alpha). Establishing a rating scale to assess the communication skills of call handlers which meets common scientific demands, such as content validity and reliability, proved successful. This instrument can be used to give feedback to call handlers.

A pilot study exploring the relationship between lifelong learning and factors associated with evidence-based medicine.

PubMed

Mi, Misa; Halalau, Alexandra

2016-07-03

To explore possible relationships between residents' lifelong learning orientation, skills in practicing evidence-based medicine (EBM), and perceptions of the environment for learning and practicing EBM. This was a pilot study with a cross-sectional survey design. Out of 60 residents in a medical residency program, 29 participated in the study. Data were collected using a survey that comprised three sections: the JeffSPLL Scale, EBM Environment Scale, and an EBM skill questionnaire. Data were analyzed using SPSS and were reported with descriptive and inferential statistics (mean, standard deviation, Pearson's correlation, and a two-sample t-test). Mean scores on the JeffSPLL Scale were significantly correlated with perceptions of the EBM Scale and use of EBM resources to keep up to date or solve a specific patient care problem. There was a significant correlation between mean scores on the EBM Scale and hours per week spent in reading medical literature to solve a patient care problem. Two-sample t-tests show that residents with previous training in research methods had significantly higher scores on the JeffSPLL Scale (p=0.04), EBM Scale (p=0.006), and self-efficacy scale (p =0.024). Given the fact that physicians are expected to be lifelong learners over the course of their professional career, developing residents' EBM skills and creating interventions to improve specific areas in the EBM environment would likely foster residents' lifelong learning orientation.

THE FATE OF TRACE METALS IN A ROTARY KILN INCINERATOR WITH A VENTURI/PACKED COLUMN SCRUBBER - VOLUME I: TECHNICAL RESULTS

EPA Science Inventory

A five week series of pilot-scale incineration tests, using a synthetic waste feed, was performed at the Environmental Protection Agency's Incineration Research Facility to evaluate the fate of trace metals fed to a rotary kiln incinerator. Eight tests studied the fate of five ha...

Natural Pressure-Driven Passive Bioventing

DTIC Science & Technology

2000-09-01

8217 300’ PFFA SCALE : 1 "= 300’ LEGEND 0 ABOVE GROUND STORAGE TANK I BUILDING FENCE = = = : DRAINAGE CHANNEL \\731272\\REPORT\\FINAL\\GRA PHICS...preparation for full- scale design of a conventional bioventing system at the PFFA, a bioventing pilot test was conducted in the demonstration area prior...PFFAVW02 @ @ PFFABOS02 PFFAVMP14..6. @ PFFABOS04 • PFFABOS06 CPT-BOSSA @ PFFABOS08 ~ JM11 ~? r 1,o v SCALE IN FEET FIGURE 6 SITE PLAN PFFA

Instrument development and validation of a quality scale for historical research papers (QSHRP): a pilot study.

PubMed

Kelly, Jacinta; Watson, Roger

2014-12-01

To report a pilot study for the development and validation of an instrument to measure quality in historical research papers. There are no set criteria to assess historical papers published in nursing journals. A three phase mixed method sequential confirmatory design. In 2012, we used a three-phase approach to item generation and content evaluation. In phase 1, we consulted nursing historians using an online survey comprising three open-ended questions and revised the items. In phase 2, we evaluated the revised items for relevance with expert historians using a 4-point Likert scale and Content Validity Index calculation. In phase 3, we conducted reliability testing of the instrument using a 3-point Likert scale. In phase 1, 121 responses were generated via the online survey and revised to 40 interrogatively phrased items. In phase 2, five items with an Item Content Validity Index score of ≥0·7 remained. In phase 3, responses from historians resulted in 100% agreement to questions 1, 2 and 4 and 89% and 78%, respectively, to questions 3 and 5. Items for the QSHRP have been identified, content validated and reliability tested. This scale improves on previous scales, which over-emphasized source criticism. However, a full-scale study is needed with nursing historians to increase its robustness. © 2014 John Wiley & Sons Ltd.

Regeneration of Full Scale Adsorptive Media Systems - Update

EPA Science Inventory

Presentation provides a short summary of the USEPA arsenic demonstration program followed by some results of lab and pilot tests on the regeneration of a number of exhausted media products collected from several demonstration projects. Following this short introduction, the pres...

Manned Versus Unmanned Risk and Complexity Considerations for Future Midsized X-Planes

NASA Technical Reports Server (NTRS)

Lechniak, Jason A.; Melton, John E.

2017-01-01

The objective of this work was to identify and estimate complexity and risks associated with the development and testing of new low-cost medium-scale X-plane aircraft primarily focused on air transport operations. Piloting modes that were evaluated for this task were manned, remotely piloted, and unmanned flight research programs. This analysis was conducted early in the data collection period for X-plane concept vehicles before preliminary designs were complete. Over 50 different aircraft and system topics were used to evaluate the three piloting control modes. Expert group evaluations from a diverse set of pilots, engineers, and other experts at Aeronautics Research Mission Directorate centers within the National Aeronautics and Space Administration provided qualitative reasoning on the many issues surrounding the decisions regarding piloting modes. The group evaluations were numerically rated to evaluate each topic quantitatively and were used to provide independent criteria for vehicle complexity and risk. An Edwards Air Force Base instruction document was identified that emerged as a source of the effects found in our qualitative and quantitative data. The study showed that a manned aircraft was the best choice to align with test activities for transport aircraft flight research from a low-complexity and low-risk perspective. The study concluded that a manned aircraft option would minimize the risk and complexity to improve flight-test efficiency and bound the cost of the flight-test portion of the program. Several key findings and discriminators between the three modes are discussed in detail.

Hanford’s Supplemental Treatment Project: Full-Scale Integrated Testing of In-Container-Vitrification and a 10,000-Liter Dryer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Witwer, Keith S.; Dysland, Eric J.; Garfield, J. S.

2008-02-22

The GeoMelt® In-Container Vitrification™ (ICV™) process was selected by the U.S. Department of Energy (DOE) in 2004 for further evaluation as the supplemental treatment technology for Hanford’s low-activity waste (LAW). Also referred to as “bulk vitrification,” this process combines glass forming minerals, LAW, and chemical amendments; dries the mixture; and then vitrifies the material in a refractory-lined steel container. AMEC Nuclear Ltd. (AMEC) is adapting its GeoMelt ICV™ technology for this application with technical and analytical support from Pacific Northwest National Laboratory (PNNL). The DVBS project is funded by the DOE Office of River Protection and administered by CH2M HILLmore » Hanford Group, Inc. The Demonstration Bulk Vitrification Project (DBVS) was initiated to engineer, construct, and operate a full-scale bulk vitrification pilot-plant to treat up to 750,000 liters of LAW from Waste Tank 241-S-109 at the DOE Hanford Site. Since the beginning of the DBVS project in 2004, testing has used laboratory, crucible-scale, and engineering-scale equipment to help establish process limitations of selected glass formulations and identify operational issues. Full-scale testing has provided critical design verification of the ICV™ process before operating the Hanford pilot-plant. In 2007, the project’s fifth full-scale test, called FS-38D, (also known as the Integrated Dryer Melter Test, or IDMT,) was performed. This test had three primary objectives: 1) Demonstrate the simultaneous and integrated operation of the ICV™ melter with a 10,000-liter dryer, 2) Demonstrate the effectiveness of a new feed reformulation and change in process methodology towards reducing the production and migration of molten ionic salts (MIS), and, 3) Demonstrate that an acceptable glass product is produced under these conditions. Testing was performed from August 8 to 17, 2007. Process and analytical results demonstrated that the primary test objectives, along with a dozen supporting objectives, were successfully met. Glass performance exceeded all disposal performance criteria. A previous issue with MIS containment was successfully resolved in FS-38D, and the ICV™ melter was integrated with a full-scale, 10,000-liter dryer. This paper describes the rationale for performing the test, the purpose and outcome of scale-up tests preceding it, and the performance and outcome of FS-38D.« less

Comparison of 2 ultrafiltration systems for the concentration of seeded viruses from environmental waters.

PubMed

Olszewski, John; Winona, Linda; Oshima, Kevin H

2005-04-01

The use of ultrafiltration as a concentration method to recover viruses from environmental waters was investigated. Two ultrafiltration systems (hollow fiber and tangential flow) in a large- (100 L) and small-scale (2 L) configuration were able to recover greater than 50% of multiple viruses (bacteriophage PP7 and T1 and poliovirus type 2) from varying water turbidities (10-157 nephelometric turbidity units (NTU)) simultaneously. Mean recoveries (n = 3) in ground and surface water by the large-scale hollow fiber ultrafiltration system (100 L) were comparable to recoveries observed in the small-scale system (2 L). Recovery of seeded viruses in highly turbid waters from small-scale tangential flow (2 L) (screen and open channel) and hollow fiber ultrafilters (2 L) (small pilot) were greater than 70%. Clogging occurred in the hollow fiber pencil module and when particulate concentrations exceeded 1.6 g/L and 5.5 g/L (dry mass) in the screen and open channel filters, respectively. The small pilot module was able to filter all concentrates without clogging. The small pilot hollow fiber ultrafilter was used to test recovery of seeded viruses from surface waters from different geographical regions in 10-L volumes. Recoveries >70% were observed from all locations.

Pilot-scale road subbase made with granular material formulated with MSWI bottom ash and stabilized APC fly ash: environmental impact assessment.

PubMed

del Valle-Zermeño, R; Formosa, J; Prieto, M; Nadal, R; Niubó, M; Chimenos, J M

2014-02-15

A granular material (GM) to be used as road sub-base was formulated using 80% of weathered bottom ash (WBA) and 20% of mortar. The mortar was prepared separately and consisted in 50% APC and 50% of Portland cement. A pilot-scale study was carried on by constructing three roads in order to environmentally evaluate the performance of GM in a real scenario. By comparing the field results with those of the column experiments, the overestimations observed at laboratory scale can be explained by the potential mechanisms in which water enters into the road body and the pH of the media. An exception was observed in the case of Cu, whose concentration release at the test road was higher. The long-time of exposure at atmospheric conditions might have favoured oxidation of organic matter and therefore the leaching of this element. The results obtained showed that immobilization of all heavy metals and metalloids from APC is achieved by the pozzolanic effect of the cement mortar. This is, to the knowledge of the authors, the only pilot scale study that is considering reutilization of APC as a safe way to disposal. Copyright © 2013 Elsevier B.V. All rights reserved.

Evaluation of a permeable reactive barrier technology for use at Rocky Flats Environmental Technology Site (RFETS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

DWYER,BRIAN P.

2000-01-01

Three reactive materials were evaluated at laboratory scale to identify the optimum treatment reagent for use in a Permeable Reactive Barrier Treatment System at Rocky Flats Environmental Technology Site (RFETS). The contaminants of concern (COCS) are uranium, TCE, PCE, carbon tetrachloride, americium, and vinyl chloride. The three reactive media evaluated included high carbon steel iron filings, an iron-silica alloy in the form of a foam aggregate, and a peculiar humic acid based sorbent (Humasorb from Arctech) mixed with sand. Each material was tested in the laboratory at column scale using simulated site water. All three materials showed promise for themore » 903 Mound Site however, the iron filings were determined to be the least expensive media. In order to validate the laboratory results, the iron filings were further tested at a pilot scale (field columns) using actual site water. Pilot test results were similar to laboratory results; consequently, the iron filings were chosen for the fill-scale demonstration of the reactive barrier technology. Additional design parameters including saturated hydraulic conductivity, treatment residence time, and head loss across the media were also determined and provided to the design team in support of the final design. The final design was completed by the Corps of Engineers in 1997 and the system was constructed in the summer of 1998. The treatment system began fill operation in December, 1998 and despite a few problems has been operational since. Results to date are consistent with the lab and pilot scale findings, i.e., complete removal of the contaminants of concern (COCs) prior to discharge to meet RFETS cleanup requirements. Furthermore, it is fair to say at this point in time that laboratory developed design parameters for the reactive barrier technology are sufficient for fuel scale design; however,the treatment system longevity and the long-term fate of the contaminants are questions that remain unanswered. This project along with others such as the Durango, CO and Monticello, UT reactive barriers will provide the data to determine the long-term effectiveness and return on investment (ROI) for this technology for comparison to the baseline pump and treat.« less

PILOT-SCALE STUDIES ON THE EFFECT OF BROMINE ADDITION ON THE EMISSIONS OF CHLORINATED ORGANIC COMBUSTION BY-PRODUCTS

EPA Science Inventory

The paper reports on a study to evaluate organic combustion by-product emissions while feeding varying amounts of bromine (Br) and chlorine (Cl) into a pilot-scale incinerator burning surrogate waste materials. (NOTE: Adding brominated organic compounds to a pilot-scale incinerat...

Comparison of NASA-TLX scale, Modified Cooper-Harper scale and mean inter-beat interval as measures of pilot mental workload during simulated flight tasks.

PubMed

Mansikka, Heikki; Virtanen, Kai; Harris, Don

2018-04-30

The sensitivity of NASA-TLX scale, modified Cooper-Harper (MCH) scale and the mean inter-beat interval (IBI) of successive heart beats, as measures of pilot mental workload (MWL), were evaluated in a flight training device (FTD). Operational F/A-18C pilots flew instrument approaches with varying task loads. Pilots' performance, subjective MWL ratings and IBI were measured. Based on the pilots' performance, three performance categories were formed; high-, medium- and low-performance. Values of the subjective rating scales and IBI were compared between categories. It was found that all measures were able to differentiate most task conditions and there was a strong, positive correlation between NASA-TLX and MCH scale. An explicit link between IBI, NASA-TLX, MCH and performance was demonstrated. While NASA-TLX, MCH and IBI have all been previously used to measure MWL, this study is the first one to investigate their association in a modern FTD, using a realistic flying mission and operational pilots.

Biogasification of community-derived biomass and solid wastes in a pilot-scale SOLCON reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Srivastava, V.J.; Biljetina, R.; Isaacson, H.R.

1988-01-01

The Institute of Gas Technology has developed a novel, solids- concentrating (SOLCON) bioreactor to convert a variety of individual or mixed feedstocks (biomass and wastes) to methane at higher rates and efficiencies than those obtained from conventional high-rate anaerobic digesters. The biogasification studies are being conducted in a pilot-scale experimental test unit (ETU) located in the Walt Disney World Resort Complex, Orlando, Florida. This paper describes the ETU facility, the logistics of feedstock integration, the SOLCON reactor design and operating techniques, and the results obtained during 4 years of stable, uninterrupted operation with different feedstocks. The SOLCON reactor consistently outperformedmore » the conventional stirred-tank reactor by 20% to 50%.« less

Full-scale Transport Controlled Impact Demonstration Program

NASA Technical Reports Server (NTRS)

1987-01-01

The Federal Aviation Administration (FAA) and NASA conducted a full-scale air-to-surface impact-survivable impact demonstration with a remotely piloted transport aircraft on 1 December 1984, at Edwards Air Force Base, California. The test article consisted of experiments, special equipment, and supporting systems, such as antimisting kerosene (AMK), crashworthiness structural/restraint, analytical modeling, cabin fire safety, flight data recorders, post-impact investigation, instrumentation/data acquisition systems, remotely piloted vehicle/flight control systems, range and flight safety provisions, etc. This report describes the aircraft, experiments, systems, activities, and events which lead up to the Controlled Impact Demonstration (CID). An overview of the final unmanned remote control flight and sequence of impact events are delineated. Preliminary post CID observations are presented.

Prevalence of fatigue in a group of airline pilots.

PubMed

Reis, Cátia; Mestre, Catarina; Canhão, Helena

2013-08-01

Fatigue is a common phenomenon in airline pilots that can impair alertness and ability of crewmembers to safely operate an aircraft and perform safety related tasks. Fatigue can increase the risk of an incident or even an accident. This study provides the first prevalence values for clinically significant fatigue in Portuguese airline pilots. The hypothesis that medium/short-haul pilots may currently present different levels of fatigue than long-haul pilots was also tested. A survey was conducted by requesting Portuguese airline pilots to complete questionnaires placed in the pilots' personal lockers from 1 April until 15 May 2012. The questionnaire included the self-response Fatigue Severity Scale (FSS) to measure subjective fatigue and some additional questions concerning perception of fatigue by pilots. The prevalence values for total and mental fatigue achieved in the Portuguese airline pilots were: 89.3% (FSS > or = 4) and 94.1% (FSS > or = 4) when splitting the sample in two subsamples, long- and medium/short-haul pilots. Levels of total and mental fatigue were higher for medium/short-haul pilots. The analysis of fatigue levels in each type of aviator showed that medium/short-haul pilots presented the highest levels of total and mental fatigue. This study produced the first prevalence values of total and mental fatigue among Portuguese airline pilots, which represents a great step to understanding and addressing this critical phenomenon.

Pilot scale evaluation of the BABIU process--upgrading of landfill gas or biogas with the use of MSWI bottom ash.

PubMed

Mostbauer, P; Lombardi, L; Olivieri, T; Lenz, S

2014-01-01

Biogas or landfill gas can be converted to a high-grade gas rich in methane with the use of municipal solid waste incineration bottom ash as a reactant for fixation of CO2 and H2S. In order to verify results previously obtained at a laboratory scale with 65-90 kg of bottom ash (BA), several test runs were performed at a pilot scale, using 500-1000 kg of bottom ash and up to 9.2 Nm(3)/h real landfill gas from a landfill in the Tuscany region (Italy). The input flow rate was altered. The best process performance was observed at a input flow rate of 3.7 Nm(3)/(htBA). At this flow rate, the removal efficiencies for H2S were approximately 99.5-99%. Copyright © 2013 Elsevier Ltd. All rights reserved.

Syngas fermentation in a 100-L pilot scale fermentor: design and process considerations.

PubMed

Kundiyana, Dimple K; Huhnke, Raymond L; Wilkins, Mark R

2010-05-01

Fermentation of syngas offers several advantages compared to chemical catalysts such as higher specificity of biocatalysts, lower energy costs, and higher carbon efficiency. Scale-up of syngas fermentation from a bench scale to a pilot scale fermentor is a critical step leading to commercialization. The primary objective of this research was to install and commission a pilot scale fermentor, and subsequently scale-up the Clostridium strain P11 fermentation from a 7.5-L fermentor to a pilot scale 100-L fermentor. Initial preparation and fermentations were conducted in strictly anaerobic conditions. The fermentation system was maintained in a batch mode with continuous syngas supply. The effect of anaerobic fermentation in a pilot scale fermentor was evaluated. In addition, the impact of improving the syngas mass transfer coefficient on the utilization and product formation was studied. Results indicate a six fold improvement in ethanol concentration compared to serum bottle fermentation, and formation of other compounds such as isopropyl alcohol, acetic acid and butanol, which are of commercial importance. (c) 2009 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

DESIGN OF A SURFACTANT REMEDIATION FIELD DEMONSTRATION BASED ON LABORATORY AND MODELINE STUDIES

EPA Science Inventory

Surfactant-enhanced subsurface remediation is being evaluated as an innovative technology for expediting ground-water remediation. This paper reports on laboratory and modeling studies conducted in preparation for a pilot-scale field test of surfactant-enhanced subsurface remedia...

METRICS OF PERFORMANCE FOR THE SABRE MICROCOSM STUDY (ABSTRACT ONLY)

EPA Science Inventory

The SABRE (Source Area BioREmediation) project will evaluate accelerated anaerobic bioremediation of chlorinated solvents in areas of high concentration, such as DNAPL source areas. In preparation for a field scale pilot test, a laboratory microcosm study was conducted to provide...

CHARACTERIZING THE MICROBIAL COMMUNITY IN SABRE MICROCOSM STUDIES (ABSTRACT ONLY)

EPA Science Inventory

The SABRE (Source Area BioREmediation) project will evaluate accelerated anaerobic bioremediation of chlorinated solvents in areas of high concentration, such as DNAPL source areas. In preparation for a field scale pilot test, laboratory microcosm and column studies were conducte...

Removal of Waterborne Particles by Electrofiltration: Pilot-Scale Testing

EPA Science Inventory

Theoretical analysis using a trajectory approach indicated that in the presence of an external electric field, charged waterborne particles are subject to an additional migration velocity which increases their deposition on the surface of collectors (e.g. sand filter). In this st...

Design and verification of a turbofan swirl augmentor

NASA Technical Reports Server (NTRS)

Egan, W. J., Jr.; Shadowen, J. H.

1978-01-01

The paper discusses the details of the design and verification testing of a full-scale turbofan 'swirl' augmentor at sea level and altitude. No flameholders are required in the swirl augmentor since the radial motion of the hot pilot gases and subsequent combustion products provides a continuous ignition front across the stream. Results of rig testing of this full-scale swirl augmentor on an F100 engine, which are very encouraging, and future development plans are presented. The results validate the application of the centrifugal-force swirling flow concept to a turbofan augmentor.

Pilot- and bench-scale testing of faecal indicator bacteria survival in marine beach sand near point sources.

PubMed

Mika, K B; Imamura, G; Chang, C; Conway, V; Fernandez, G; Griffith, J F; Kampalath, R A; Lee, C M; Lin, C-C; Moreno, R; Thompson, S; Whitman, R L; Jay, J A

2009-07-01

Factors affecting faecal indicator bacteria (FIB) and pathogen survival/persistence in sand remain largely unstudied. This work elucidates how biological and physical factors affect die-off in beach sand following sewage spills. Solar disinfection with mechanical mixing was pilot-tested as a disinfection procedure after a large sewage spill in Los Angeles. Effects of solar exposure, mechanical mixing, predation and/or competition, season, and moisture were tested at bench scale. First-order decay constants for Escherichia coli ranged between -0.23 and -1.02 per day, and for enterococci between -0.5 and -1.0 per day. Desiccation was a dominant factor for E. coli but not enterococci inactivation. Effects of season were investigated through a comparison of experimental results from winter, spring, and fall. Moisture was the dominant factor controlling E. coli inactivation kinetics. Initial microbial community and sand temperature were also important factors. Mechanical mixing, common in beach grooming, did not consistently reduce bacterial levels. Inactivation rates are mainly dependent on moisture and high sand temperature. Chlorination was an effective disinfection treatment in sand microcosms inoculated with raw influent.

Pilot scale feasibility study for in-situ chemical oxidation using H2O2 solution conjugated with biodegradation to remediate a diesel contaminated site.

PubMed

Kim, Insu; Lee, Minhee

2012-11-30

A pilot scale test for a process combining in-situ chemical oxidation using H(2)O(2) solution with biodegradation was performed to remove TPH from a diesel contaminated military site. In batch experiments, when 20% H(2)O(2) solution was used for TPH contaminated soil, TPH removal efficiency was 63.5%. Batch experiments investigating biodegradation by adding indigenous microorganisms in pre-H(2)O(2)-treated soil were also performed, and TPH removal efficiency of biodegradation was 48.5%, showing an improvement of 19.4% by biodegradation even after chemical oxidation. For a pilot scale feasibility test, a site contaminated with diesel (2.5 m × 2.7 m × 1 m) in Korea was selected, and five injection wells and one extraction well were installed in the site. After 0.3 pore volumes of 17.5% H(2)O(2) solution flushing for 15 days, TPH removal efficiency of the site was 51.5%. Seven days after the H(2)O(2) solution flushing was finished, a mixed indigenous microorganism cultured solution (43 L) was injected into the wells two times. After the injection of the cultured solution, the average concentration of TPH in the site decreased to 777 mg/kg, showing that an additional 19.6% of TPH was removed by biodegradation (total TPH removal efficiency: 71.1%). Copyright © 2012 Elsevier B.V. All rights reserved.

Spray-dry desulfurization of flue gas from heavy oil combustion.

PubMed

Scala, Fabrizio; Lancia, Amedeo; Nigro, Roberto; Volpicelli, Gennaro

2005-01-01

An experimental investigation on sulfur dioxide removal in a pilot-scale spray dryer from the flue gas generated by combustion of low-sulfur (S) heavy oil is reported. A limewater slurry was sprayed through an ultrasonic two-fluid atomizer in the spray-dry chamber, and the spent sorbent was collected downstream in a pulse-jet baghouse together with fly ash. Flue gas was sampled at different points to measure the desulfurization efficiency after both the spray-dry chamber and the baghouse. Parametric tests were performed to study the effect of the following variables: gas inlet temperature, difference between gas outlet temperature and adiabatic saturation temperature, lime-to-S ratio, and average size of lime particles in the slurry. Results indicated that spray drying is an effective technology for the desulfurization of low-S fuel oil flue gas, provided operating conditions are chosen carefully. In particular, the lowest gas inlet and outlet temperatures compatible with baghouse operation should be selected, as should a sufficiently high lime-to-S ratio. The attainment of a small lime particle size in the slurry is critical for obtaining a high desulfurization efficiency. A previously presented spray-dry flue gas desulfurization model was used to simulate the pilot-scale desulfurization tests, to check the ability of the model to predict the S capture data and its usefulness as a design tool, minimizing the need for pilot-scale experimentation. Comparison between model and experimental results was fairly good for the whole range of calcium/S ratios considered.

The psychometric testing of the Nursing Teamwork Survey in Iceland.

PubMed

Bragadóttir, Helga; Kalisch, Beatrice J; Smáradóttir, Sigríður Bríet; Jónsdóttir, Heiður Hrund

2016-06-01

The purpose of this study was to test the psychometric properties of the Nursing Teamwork Survey-Icelandic (NTS-Icelandic), which was translated from US English to Icelandic. The Nursing Teamwork Survey, with 33 items, measures overall teamwork and five factors of teamwork: trust, team orientation, backup, shared mental models, and team leadership. The psychometric testing of the NTS-Icelandic was carried out on data from a pilot study and a national study. The sample for a pilot study included 123 nursing staff from five units, and the sample for a national study included 925 nursing staff from 27 inpatient units. The overall test-retest intraclass correlation coefficient in the pilot study was 0.693 (lower bound = 0.498, upper bound = 0.821) (p < 0.001). The Cronbach's alpha reliability for the total scale and subscales ranged from 0.737 to 0.911. A confirmatory factor analysis indicated a good fit of the data from the national study with the five-factor model for nursing teamwork. The NTS-Icelandic tested valid and reliable in this study. Study findings support further use of the Nursing Teamwork Survey internationally. © 2016 John Wiley & Sons Australia, Ltd.

A Pilot Study: Testing of the Psychological Conditions Scale Among Hospital Nurses.

PubMed

Fountain, Donna M; Thomas-Hawkins, Charlotte

2016-11-01

The aim of this study was to test the reliability and validity of the Psychological Conditions Scale (PCS), a measure of drivers of engagement in hospital-based nurses. Research suggests drivers of engagement are positive links to patient, employee, and hospital outcomes. Although this scale has been used in other occupations, it has not been tested in nursing. A cross-sectional, methodological study using a convenience sample of 200 nurses in a large Magnet® hospital in New Jersey. Cronbach's α's ranged from .64 to .95. Principal components exploratory factor analysis with oblique rotation revealed that 13 items loaded unambiguously in 3 domains and explained 76% of the variance. Mean PCS scores ranged from 3.62 to 4.68 on a 5-point Likert scale. The scale is an adequate measure of drivers of engagement in hospital-based nurses. Leadership efforts to promote the facilitators of engagement are recommended.

A novel test method to determine the filter material service life of decentralized systems treating runoff from traffic areas.

PubMed

Huber, Maximilian; Welker, Antje; Dierschke, Martina; Drewes, Jörg E; Helmreich, Brigitte

2016-09-01

In recent years, there has been a significant increase in the development and application of technical decentralized filter systems for the treatment of runoff from traffic areas. However, there are still many uncertainties regarding the service life and the performance of filter materials that are employed in decentralized treatment systems. These filter media are designed to prevent the transport of pollutants into the environment. A novel pilot-scale test method was developed to determine - within a few days - the service lives and long-term removal efficiencies for dissolved heavy metals in stormwater treatment systems. The proposed method consists of several steps including preloading the filter media in a pilot-scale model with copper and zinc by a load of n-1 years of the estimated service life (n). Subsequently, three representative rain events are simulated to evaluate the long-term performance by dissolved copper and zinc during the last year of application. The presented results, which verified the applicability of this method, were obtained for three filter channel systems and six filter shaft systems. The performance of the evaluated systems varied largely for both tested heavy metals and during all three simulated rain events. A validation of the pilot-scale assessment method with field measurements was also performed for two systems. Findings of this study suggest that this novel method does provide a standardized and accurate estimation of service intervals of decentralized treatment systems employing various filter materials. The method also provides regulatory authorities, designers, and operators with an objective basis for performance assessment and supports stormwater managers to make decisions for the installation of such decentralized treatment systems. Copyright © 2016 Elsevier Ltd. All rights reserved.

Performance of granular activated carbon to remove micropollutants from municipal wastewater-A meta-analysis of pilot- and large-scale studies.

PubMed

Benstoem, Frank; Nahrstedt, Andreas; Boehler, Marc; Knopp, Gregor; Montag, David; Siegrist, Hansruedi; Pinnekamp, Johannes

2017-10-01

For reducing organic micropollutants (MP) in municipal wastewater effluents, granular activated carbon (GAC) has been tested in various studies. We did systematic literature research and found 44 studies dealing with the adsorption of MPs (carbamazepine, diclofenac, sulfamethoxazole) from municipal wastewater on GAC in pilot- and large-scale plants. Within our meta-analysis we plot the bed volumes (BV [m 3 water /m 3 GAC ]) until the breakthrough criterion of MP-BV20% was reached, dependent on potential relevant parameters (empty bed contact time EBCT, influent DOC DOC 0 and manufacturing method). Moreover, we performed statistical tests (ANOVAs) to check the results for significance. Single adsorbers operating time differs i.e. by 2500% until breakthrough of diclofenac-BV20% was reached (800-20,000 BV). There was still elimination of the "very well/well" adsorbable MPs such as carbamazepine and diclofenac even when the equilibrium of DOC had already been reached. No strong statistical significance of EBCT and DOC 0 on MP-BV20% could be found due to lack of data and the high heterogeneity of the studies using GAC of different qualities. In further studies, adsorbers should be operated ≫20,000 BV for exact calculation of breakthrough curves, and the following parameters should be recorded: selected MPs; DOC 0; UVA 254 ; EBCT; product name, manufacturing method and raw material of GAC; suspended solids (TSS); backwash interval; backwash program and pressure drop within adsorber. Based on our investigations we generally recommend using reactivated GAC to reduce the environmental impact and to carry out tests on pilot scale to collect reliable data for process design. Copyright © 2017 Elsevier Ltd. All rights reserved.

Integrated System Health Management: Pilot Operational Implementation in a Rocket Engine Test Stand

NASA Technical Reports Server (NTRS)

Figueroa, Fernando; Schmalzel, John L.; Morris, Jonathan A.; Turowski, Mark P.; Franzl, Richard

2010-01-01

This paper describes a credible implementation of integrated system health management (ISHM) capability, as a pilot operational system. Important core elements that make possible fielding and evolution of ISHM capability have been validated in a rocket engine test stand, encompassing all phases of operation: stand-by, pre-test, test, and post-test. The core elements include an architecture (hardware/software) for ISHM, gateways for streaming real-time data from the data acquisition system into the ISHM system, automated configuration management employing transducer electronic data sheets (TEDS?s) adhering to the IEEE 1451.4 Standard for Smart Sensors and Actuators, broadcasting and capture of sensor measurements and health information adhering to the IEEE 1451.1 Standard for Smart Sensors and Actuators, user interfaces for management of redlines/bluelines, and establishment of a health assessment database system (HADS) and browser for extensive post-test analysis. The ISHM system was installed in the Test Control Room, where test operators were exposed to the capability. All functionalities of the pilot implementation were validated during testing and in post-test data streaming through the ISHM system. The implementation enabled significant improvements in awareness about the status of the test stand, and events and their causes/consequences. The architecture and software elements embody a systems engineering, knowledge-based approach; in conjunction with object-oriented environments. These qualities are permitting systematic augmentation of the capability and scaling to encompass other subsystems.

High subsonic flow tests of a parallel pipe followed by a large area ratio diffuser

NASA Technical Reports Server (NTRS)

Barna, P. S.

1975-01-01

Experiments were performed on a pilot model duct system in order to explore its aerodynamic characteristics. The model was scaled from a design projected for the high speed operation mode of the Aircraft Noise Reduction Laboratory. The test results show that the model performed satisfactorily and therefore the projected design will most likely meet the specifications.

Measuring social alienation in adolescence: translation and validation of the Jessor and Jessor Social Alienation Scale.

PubMed

Safipour, Jalal; Tessma, Mesfin Kassaye; Higginbottom, Gina; Emami, Azita

2010-12-01

The objective of the study is to translate and examine the reliability and validity of the Jessor and Jessor Social Alienation Scale for use in a Swedish context. The study involved four phases of testing: (1) Translation and back-translation; (2) a pilot test to evaluate the translation; (3) reliability testing; and (4) a validity test. Main participants of this study were 446 students (Age = 15-19, SD = 1.01, Mean = 17). Results from the reliability test showed high internal consistency and stability. Face, content and construct validity were demonstrated using experts and confirmatory factor analysis. The results of testing the Swedish version of the alienation scale revealed an acceptable level of reliability and validity, and is appropriate for use in the Swedish context. © 2010 The Authors. Scandinavian Journal of Psychology © 2010 The Scandinavian Psychological Associations.

Extraction of mercury from groundwater using immobilized algae.

PubMed

Barkley, N P

1991-10-01

Bio-Recovery Systems, Inc. conducted a project under the Emerging Technology portion of the United States Environmental Protection Agency's (EPAs) Superfund Innovative Technology Evaluation (SITE) Program to evaluate the ability of immobilized algae to adsorb mercury from contaminated groundwater in laboratory studies and pilot-scale field tests. Algal biomass was incorporated in a permeable polymeric matrix. The product, AlgaSORB, packed into adsorption columns, exhibited excellent flow characteristics, and functioned as a "biological" ion exchange resin. A sequence of eleven laboratory tests demonstrated the ability of this product to adsorb mercury from groundwater that contained high levels of total dissolved solids and hard water components. However, use of a single AlgaSORB preparation yielded nonrepeatable results with samples collected at different times of the year. The strategy of sequentially extracting the groundwater through two columns containing different preparations of AlgaSORB was developed and proved successful in laboratory and pilot-scale field tests. Field test results indicate that AlgaSORB could be economically competitive with ion exchange resins for removal of mercury, with the advantage that hardness and other dissolved solids do not appear to compete with heavy metals for binding capacity.

Field test comparison of two dermal tolerance assessment methods of hand hygiene products.

PubMed

Girard, R; Carré, E; Pires-Cronenberger, S; Bertin-Mandy, M; Favier-Bulit, M C; Coyault, C; Coudrais, S; Billard, M; Regard, A; Kerhoas, A; Valdeyron, M L; Cracco, B; Misslin, P

2008-06-01

This study aimed to compare the sensitivity and workload requirement of two dermal tolerance assessment methods of hand hygiene products, in order to select a suitable pilot testing method for field tests. An observer-rating method and a self-assessment method were compared in 12 voluntary hospital departments (autumn/winter of 2005-2006). Three test-periods of three weeks were separated by two-week intervals during which the routine products were reintroduced. The observer rating method scored dryness and irritation on four-point scales. In the self-assessment method, the user rated appearance, intactness, moisture content, and sensation on a visual analogue scale which was converted into a 10-point numerical scale. Eleven products (soaps) were tested (223/250 complete reports for observer rating, 131/251 for self-assessment). Two products were significantly less well tolerated than the routine product according to the observers, four products according to the self-assessments. There was no significant difference between the two methods when products were classified according to tolerance (Fisher's test: P=0.491). For the symptom common to both assessment methods (dryness), there is a good correlation between the two methods (Spearman's Rho: P=0.032). The workload was higher for observer rating method (288 h of observer time plus 122 h of prevention team and pharmacist time compared with 15 h of prevention team and pharmacist time for self-assessment). In conclusion, the self-assessment method was considered more suitable for pilot testing, although further time should be allocated for educational measures as the return rate of complete self-assessment forms was poor.

Furniture wood wastes: Experimental property characterisation and burning tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tatano, Fabio; Barbadoro, Luca; Mangani, Giovanna

2009-10-15

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected 'raw' and primarily 'engineered' ('composite') wood wastes. The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in 'engineered' wood wastes as compared with 'raw' wood wastes; and relatively high energy content values of 'engineered' wood wastes (ranging on the whole from 3675more » to 5105 kcal kg{sup -1} for HHV, and from 3304 to 4634 kcal kg{sup -1} for LHV). The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in 'engineered' wood burning tests of pyrroles and amines, as well as the additional presence (as compared with 'raw' wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon. Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in 'engineered' wood burning tests as compared with 'raw' wood burning test; and considerable generation of the respirable PM{sub 1} fraction during incomplete industrial wood burning.« less

Design and evaluation of hydraulic baffled-channel PAC contactor for taste and odor removal from drinking water supplies.

PubMed

Kim, Young-Il; Bae, Byung-Uk

2007-05-01

Based on the concept of hydraulic flocculator, a baffled-channel powdered activated carbon (PAC) contactor, placed before the rapid-mixing basin, was designed and evaluated for removal of taste and odor (T&O) in drinking water. PAC adsorption kinetic tests for raw water samples were conducted for selection of design parameters related to contact time and degree of mixing. Within the tested range of velocity gradient (G) from 18 to 83s(-1), mixing had a relatively minor effect on the adsorption kinetics of the PAC. The hydrodynamic characteristics of the pilot-scale horizontally and vertically baffled-channel PAC contactor were investigated by tracer tests. It was found that the plug flow fractions of vertically baffled-channel PAC contactor (vBPC) were higher than those of the horizontally baffled-channel PAC contactor (hBPC) for the same bend width or bend height. However, the hBPC seems to be more appropriate than the vBPC in terms of construction and maintenance. The geosmin and MIB removal rate increased with the number of baffles, PAC dose and contact time increased regardless of bend width in the pilot-scale hBPC. The pair of full-scale hBPCs at Pohang water treatment plant, having a design capacity of 6.5x10(4)m(3)/d with 20min of hydraulic retention time with a safety factor of 2, was designed based on lab- and pilot-scale experimental results. Under a velocity gradient of 20s(-1), the number of baffles to be installed was calculated to be 20 with a space of about 2m between each baffle, resulting in a hydraulic head loss through the contactor of about 0.056m. The successful application of hBPC for T&O removal from drinking water supplies should provide momentum for developing more effective treatment methods.

Fuel-Flexible Gasification-Combustion Technology for Production of H2 and Sequestration-Ready CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Raul Subia

GE Global Research is developing an innovative energy technology for coal gasification with high efficiency and near-zero pollution. This Unmixed Fuel Processor (UFP) technology simultaneously converts coal, steam and air into three separate streams of hydrogen-rich gas, sequestration-ready CO{sub 2}, and high-temperature, high-pressure vitiated air to produce electricity in gas turbines. This is the draft final report for the first stage of the DOE-funded Vision 21 program. The UFP technology development program encompassed lab-, bench- and pilot-scale studies to demonstrate the UFP concept. Modeling and economic assessments were also key parts of this program. The chemical and mechanical feasibility weremore » established via lab and bench-scale testing, and a pilot plant was designed, constructed and operated, demonstrating the major UFP features. Experimental and preliminary modeling results showed that 80% H{sub 2} purity could be achieved, and that a UFP-based energy plant is projected to meet DOE efficiency targets. Future work will include additional pilot plant testing to optimize performance and reduce environmental, operability and combined cycle integration risks. Results obtained to date have confirmed that this technology has the potential to economically meet future efficiency and environmental performance goals.« less

U.S. ENVIRONMENTAL PROTECTION AGENCY'S SITE EMERGING TECHNOLOGY PROGRAM: 1991 UPDATE

EPA Science Inventory

The Emerging Technology Program (ETP) supports the development of technologies successfully tested at the bench- and pilot-scale level. The ETP is part of the Superfund Innovative Technology Evaluation (SITE) Program which was established in 1986 under the Superfund Amendments an...

PILOT-SCALE INCINERATION OF CONTAMINATED SLUDGES FROM THE BOFORS-NOBEL SUPERFUND SITE

EPA Science Inventory

A detailed test program was performed at the U.S. Environmental Protection Agency’s (EPA’s) Incineration Research Facility (IRF) to help determine the effectiveness of incineration in treating two contaminated lagoon sludges from the Bofors-Nobel Superfund site in Mus...

1992 UPDATE OF U.S. EPA'S SUPERFUND INNOVATIVE TECHNOLOGY EVALUATION (SITE) EMERGING TECHNOLOGY PROGRAM

EPA Science Inventory

The Superfund Innovative Technology Evaluation (SITE) Emerging Technology Program (ETP) has encouraged and financially supported further development of bench- and pilot-scale testing and evaluation of innovative technologies suitable for use at hazardous waste sites for five year...

A pilot scale comparison of advanced oxidation processes for estrogenic hormone removal from municipal wastewater effluent.

PubMed

Pešoutová, Radka; Stříteský, Luboš; Hlavínek, Petr

2014-01-01

This study investigates the oxidation of selected endocrine disrupting compounds (estrone, 17β-estradiol, estriol and 17α-ethinylestradiol) during ozonation and advanced oxidation of biologically treated municipal wastewater effluents in a pilot scale. Selected estrogenic substances were spiked in the treated wastewater at levels ranging from 1.65 to 3.59 μg · L(-1). All estrogens were removed by ozonation by more than 99% at ozone doses ≥1.8 mg · L(-1). At a dose of 4.4 · mg L(-1) ozonation reduced concentrations of estrone, 17β-estradiol, estriol and 17α-ethinylestradiol by 99.8, 99.7, 99.9 and 99.7%, respectively. All tested advanced oxidation processes (AOPs) achieved high removal rates but they were slightly lower compared to ozonation. The lower removal rates for all tested advanced oxidation processes are caused by the presence of naturally occurring hydroxyl radical scavengers - carbonates and bicarbonates.

Solid-state fermentation of soybean residues for bioflocculant production in a pilot-scale bioreactor system.

PubMed

Zulkeflee, Zufarzaana; Sánchez, Antoni

2014-01-01

An innovative approach using soybean residues for the production of bioflocculants through solid-state fermentation was carried out in 4.5 L near-to-adiabatic bioreactors at pilot-scale level. An added inoculum of the strain Bacillus subtilis UPMB13 was tested in comparison with control reactors without any inoculation after the thermophilic phase of the fermentation. The flocculating performances of the extracted bioflocculants were tested on kaolin suspensions, and crude bioflocculants were obtained from 20 g of fermented substrate through ethanol precipitation. The production of bioflocculants was observed to be higher during the death phase of microbial growth. The bioflocculants were observed to be granular in nature and consisted of hydroxyl, carboxyl and methoxyl groups that aid in their flocculating performance. The results show the vast potential of the idea of using wastes to produce bioactive materials that can replace the current dependence on chemicals, for future prospect in water treatment applications.

Equipment evaluation for low density polyethylene encapsulated nitrate salt waste at the Rocky Flats Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamada, W.I.; Faucette, A.M.; Jantzen, R.C.

1993-08-30

Mixed wastes at the Rocky Flats Plant (RFP) are subject to regulation by the Resource Conservation and Recovery Act (RCRA). Polymer solidification is being developed as a final treatment technology for several of these mixed wastes, including nitrate salts. Encapsulation nitrate salts with low density polyethylene (LDPE) has been the preliminary focus of the RFP polymer solidification effort. Literature reviews, industry surveys, and lab-scale and pilot-scale tests have been conducted to evaluate several options for encapsulating nitrate salts with LDPE. Most of the effort has focused on identifying compatible drying and extrusion technologies. Other processing options, specifically meltration and non-heatedmore » compounding machines, were also investigated. The best approach appears to be pretreatment of the nitrate salt waste brine in either a vertical or horizontal thin film evaporator followed by compounding of the dried waste with LDPE in an intermeshing, co-rotating, twin-screw extruder. Additional pilot-scale tests planned for the fall of 1993 should further support this recommendation. Preliminary evaluation work indicates that meltration is not possible at atmospheric pressure with the LDPE (Chevron PE-1409) provided by RFP. However, meltration should be possible at atmospheric pressure using another LDPE formulation with altered physical and rheological properties: Lower molecular weight and lower viscosity (Epoline C-15). Contract modifications are now in process to allow a follow-on pilot scale demonstration. Questions regarding changed safety and physical properties of the resultant LDPE waste form due to use of the Epoline C-15 will be addressed. No additional work with non-heated mixer compounder machines is planned at this time.« less

Cultural Adaptation Quality of Family Life Scale for the Brazilian Portuguese.

PubMed

Jorge, Bianca Miguel; Levy, Cilmara Cristina Alves da Costa; Granato, Lídio

2015-01-01

To culturally adapt the Family Quality of Life Scale to the Brazilian Portuguese version and evaluate the instrument reliability and family quality of life of those who have children with hearing loss. The process of cultural adaptation of the scale followed the steps of the Guidelines for the Process of Cross-Cultural Adaptation of Self-Report Measure. It was conducted in three stages: translation, back translation, and application in a pilot sample, as a way to check the comprehension difficulties of the items. After it had been completed, it was administered to 41 families who have children with hearing loss and, with their results, the quality of life and reliability were analyzed based on the Cronbach's alpha statistical test. In the first version (translation), among the 25 items, there were differences between the translators only in four items; after the corrections, the second version was done (back translation), in which other four more differences were found. Finally, after the final corrections, the last version was developed and used in the pilot sample without differences. Thus, it was applied to families with deaf children, who believe to be satisfied as to their quality of life. The Cronbach's alpha test found that the scale shows a satisfactory reliability. The Brazilian Portuguese version of the Family Quality of Life Scale is a tool of easy use and satisfactory reliability. The families are satisfied with their family quality of life.

Pilot-scale cooling tower to evaluate corrosion, scaling, and biofouling control strategies for cooling system makeup water.

PubMed

Chien, S H; Hsieh, M K; Li, H; Monnell, J; Dzombak, D; Vidic, R

2012-02-01

Pilot-scale cooling towers can be used to evaluate corrosion, scaling, and biofouling control strategies when using particular cooling system makeup water and particular operating conditions. To study the potential for using a number of different impaired waters as makeup water, a pilot-scale system capable of generating 27,000 kJ∕h heat load and maintaining recirculating water flow with a Reynolds number of 1.92 × 10(4) was designed to study these critical processes under conditions that are similar to full-scale systems. The pilot-scale cooling tower was equipped with an automatic makeup water control system, automatic blowdown control system, semi-automatic biocide feeding system, and corrosion, scaling, and biofouling monitoring systems. Observed operational data revealed that the major operating parameters, including temperature change (6.6 °C), cycles of concentration (N = 4.6), water flow velocity (0.66 m∕s), and air mass velocity (3660 kg∕h m(2)), were controlled quite well for an extended period of time (up to 2 months). Overall, the performance of the pilot-scale cooling towers using treated municipal wastewater was shown to be suitable to study critical processes (corrosion, scaling, biofouling) and evaluate cooling water management strategies for makeup waters of complex quality.

Autogenic-feedback training as a treatment for airsickness in high-performance military aircraft: Two case studies

NASA Technical Reports Server (NTRS)

Cowings, Patricia S.; Toscano, William B.; Miller, Neal E.; Reynoso, Samuel

1994-01-01

The purpose of this paper is to present a detailed description of the physiological and performance responses of two military pilots undergoing a treatment for motion sickness. The treatment used, Autogenic-Feedback Training (AFT), is an operant conditioning procedure where subjects are taught to control several of their autonomic responses and thereby suppress their motion sickness symptoms. Two male, active duty military pilots (U.S. Navy and U. S. Marine Corps), ages 30 and 35, were each given twelve 30-minute training sessions. The primary criterion for success of training was the subject's ability to tolerate rotating chair motion sickness tests for progressively longer periods of time and at higher rotational velocities. A standardized diagnostic scale was used during motion sickness to assess changes in the subject's perceived malaise. Physiological data were obtained from one pilot during tactical maneuvers in an F-18 aircraft after completion of his training. A significant increase in tolerance to laboratory-induced motion sickness tests and a reduction in autonomic nervous system (ANS) response variability was observed for both subjects after training. Both pilots were successful in applying AFT for controlling their airsickness during subsequent qualification tests on F-18 and T-38 aircraft and were returned to active duty flight status.

Fire Resistance of Geopolymer Concretes

DTIC Science & Technology

2010-03-21

1 Project report – Grant FA23860814096, "Fire resistance of geopolymer concretes" – J. Provis, University of Melbourne 1. Background and...experimental program This project provided funding for us to carry out fire testing of geopolymer concrete specimens and associated laboratory...testing. The focus of this report will be the outcomes of the series of pilot-scale (4’×4’×6”) tests on geopolymer concrete panels, which were conducted

Development of the Holistic Nursing Competence Scale.

PubMed

Takase, Miyuki; Teraoka, Sachiko

2011-12-01

This study developed a scale to measure the nursing competence of Japanese registered nurses and to test its psychometric properties. Following the derivation of scale items and pilot testing, the final version of the scale was administered to 331 nurses to establish its internal consistency, as well as its construct and criterion-related validity. Using an exploratory and a confirmatory factor analysis, 36 items with a five-factor structure were retained to form the Holistic Nursing Competence Scale. These factors illustrate nurses' general aptitude and their competencies in staff education and management, ethical practice, the provision of nursing care, and professional development. The Scale has a positive correlation with the length of clinical experience. A Cronbach's alpha coefficient was 0.967. The Scale is a reliable and valid measure, helping both nurses and organizations to correctly evaluate nurses' competence and identify their needs for professional development. © 2011 Blackwell Publishing Asia Pty Ltd.

Pilot-Scale Test of Counter-Current Ion Exchange (CCIX) Using UOP IONSIV IE-911

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wester, Dennis W; Leugemors, Robert K; Taylor, Paul W

2001-09-24

A pilot-scale test of a moving-bed configuration of a UOP IONSIV? IE-911 ion-exchange column was performed over 17 days at Severn Trent Services facilities. The objectives of the test, in order of priority, were to determine if aluminosilicate precipitation caused clumping of IE-911 particles in the column, to observe the effect on aluminum-hydroxide precipitation of water added to a simulant-filled column, to evaluate the extent of particle attrition, and to measure the expansion of the mass-transfer zone under the influence of column pulsing. The IE-911 moved through the column with no apparent clumping during the test, although analytical results indicatemore » that little if any aluminosilicate precipitated onto the particles. A precipitate of aluminum hydroxide was not produced when water was added to the simulant-filled column, indicating that this upset scenario is probably of little concern. Particle-size distributions remained relatively constant with time and position in the column, indicating that particle attrition was not significant. The expansion of the mass-transfer zone could not be accurately measured because of the slow loading kinetics of the IE-911 and the short duration of the test; however, the information obtained indicates that back-mixing of sorbent is not extensive.« less

Launch Vehicle Manual Steering with Adaptive Augmenting Control:In-Flight Evaluations of Adverse Interactions Using a Piloted Aircraft

NASA Technical Reports Server (NTRS)

Hanson, Curt; Miller, Chris; Wall, John H.; VanZwieten, Tannen S.; Gilligan, Eric T.; Orr, Jeb S.

2015-01-01

An Adaptive Augmenting Control (AAC) algorithm for the Space Launch System (SLS) has been developed at the Marshall Space Flight Center (MSFC) as part of the launch vehicle's baseline flight control system. A prototype version of the SLS flight control software was hosted on a piloted aircraft at the Armstrong Flight Research Center to demonstrate the adaptive controller on a full-scale realistic application in a relevant flight environment. Concerns regarding adverse interactions between the adaptive controller and a potential manual steering mode were also investigated by giving the pilot trajectory deviation cues and pitch rate command authority, which is the subject of this paper. Two NASA research pilots flew a total of 25 constant pitch rate trajectories using a prototype manual steering mode with and without adaptive control, evaluating six different nominal and off-nominal test case scenarios. Pilot comments and PIO ratings were given following each trajectory and correlated with aircraft state data and internal controller signals post-flight.

UV/H2O2 process stability and pilot-scale validation for trace organic chemical removal from wastewater treatment plant effluents.

PubMed

Miklos, David B; Hartl, Rebecca; Michel, Philipp; Linden, Karl G; Drewes, Jörg E; Hübner, Uwe

2018-06-01

This study investigated the removal of 15 trace organic chemicals (TOrCs) occurring at ambient concentrations from municipal wastewater treatment plant effluent by advanced oxidation using UV/H 2 O 2 at pilot-scale. Pseudo first-order rate constants (k obs ) for photolytic as well as combined oxidative and photolytic degradation observed at pilot-scale were validated with results from a bench-scale collimated beam device. No significant difference was determined between pilot- and lab-scale performance. During continuous pilot-scale operation at constant UV fluence of 800 mJ/cm 2 and H 2 O 2 dosage of 10 mg/L, the removal of various TOrCs was investigated. The average observed removal for photo-susceptible (k UV >10 -3  cm 2 /mJ; like diclofenac, iopromide and sulfamethoxazole), moderately photo-susceptible (10 -4

The Development and Preliminary Testing of an Instrument for Assessing Fatigue Self-management Outcomes in Patients With Advanced Cancer.

PubMed

Chan, Raymond Javan; Yates, Patsy; McCarthy, Alexandra L

Fatigue is one of the most distressing and commonly experienced symptoms in patients with advanced cancer. Although the self-management (SM) of cancer-related symptoms has received increasing attention, no research instrument assessing fatigue SM outcomes for patients with advanced cancer is available. The aim of this study was to describe the development and preliminary testing of an interviewer-administered instrument for assessing the frequency and perceived levels of effectiveness and self-efficacy associated with fatigue SM behaviors in patients with advanced cancer. The development and testing of the Self-efficacy in Managing Symptoms Scale-Fatigue Subscale for Patients With Advanced Cancer (SMSFS-A) involved a number of procedures: item generation using a comprehensive literature review and semistructured interviews, content validity evaluation using expert panel reviews, and face validity and test-retest reliability evaluation using pilot testing. Initially, 23 items (22 specific behaviors with 1 global item) were generated from the literature review and semistructured interviews. After 2 rounds of expert panel review, the final scale was reduced to 17 items (16 behaviors with 1 global item). Participants in the pilot test (n = 10) confirmed that the questions in this scale were clear and easy to understand. Bland-Altman analysis showed agreement of results over a 1-week interval. The SMSFS-A items were generated using multiple sources. This tool demonstrated preliminary validity and reliability. The SMSFS-A has the potential to be used for clinical and research purposes. Nurses can use this instrument for collecting data to inform the initiation of appropriate fatigue SM support for this population.

Early flight test experience with Cockpit Displayed Traffic Information (CDTI)

NASA Technical Reports Server (NTRS)

Abbott, T. S.; Moen, G. C.; Person, L. H., Jr.; Keyser, G. L., Jr.; Yenni, K. R.; Garren, J. F., Jr.

1980-01-01

Coded symbology, based on the results of early human factors studies, was displayed on the electronic horizontal situation indicator and flight tested on an advanced research aircraft in order to subject the coded traffic symbology to a realistic flight environment and to assess its value by means of a direct comparison with simple, uncoded traffic symbology. The tests consisted of 28 curved, decelerating approaches, flown by research-pilot flight crews. The traffic scenarios involved both conflict-free and blunder situations. Subjective pilot commentary was obtained through the use of a questionnaire and extensive pilot debriefing sessions. The results of these debriefing sessions group conveniently under either of two categories: display factors or task performance. A major item under the display factor category was the problem of display clutter. The primary contributors to clutter were the use of large map-scale factors, the use of traffic data blocks, and the presentation of more than a few aircraft. In terms of task performance, the cockpit displayed traffic information was found to provide excellent overall situation awareness.

The Politics of Aviation English Testing

ERIC Educational Resources Information Center

Alderson, J. Charles

2011-01-01

The International Civil Aviation Association has developed a set of Language Proficiency Requirements (LPRs) and a Language Proficiency Rating Scale, which seeks to define proficiency in the language needed for aviation purposes at six different levels. Pilots, air traffic controllers and aeronautical station operators are required to achieve at…

SITE - EMERGING TECHNOLOGY: REMOVAL AND RECOVERY OF METAL IONS FROM GROUNDWATER - APPENDICES

EPA Science Inventory

A series of laboratory tests and an on-site pilot scale demonstration of Bio-Recovery Systems' AlgaSORB technology for the removal and recovery of mercury-contaminated groundwater were conducted under the SITE program. ptimum conditions were determined for mercury binding to Alga...

DEVELOPMENT OF A HAZARDOUS WASTE INCINERATOR TARGET ANALYTE LIST OF PRODUCTS OF INCOMPLETE COMBUSTION

EPA Science Inventory

The report gives results of pilot-scale incineration testing to develop a comprehensive list of products of incomplete combustion (PICs) from hazardous waste combustion (HWC) systems. Project goals were to: (1) identify the total mass of organic compounds sufficiently to estimate...

Development and pilot testing of a disease management program for low literacy patients with heart failure.

PubMed

DeWalt, Darren A; Pignone, Michael; Malone, Robb; Rawls, Cathy; Kosnar, Margaret C; George, Geeta; Bryant, Betsy; Rothman, Russell L; Angel, Bonnie

2004-10-01

Development and pilot testing of a disease management program for low literacy patients with heart failure. Randomized trials have shown that disease management programs can reduce hospitalizations and improve symptoms for patients with congestive heart failure. We sought to create and pilot test such a program for patients with low literacy skills. We used focus groups and individual cognitive response interviews (CRIs) to develop an educational booklet for low literacy patients with heart failure. We incorporated the booklet into a disease management intervention that also included an initial individualized 1-h educational session and scheduled supportive phone calls that were tapered over 6 weeks. We then conducted a 3-month before-after study on patients with low literacy skills (<9th grade literacy level) in a university internal medicine clinic to test the acceptability and efficacy of our program. Outcomes of interest included heart failure-related knowledge, self-care behavior and heart failure-related symptoms measured on the Minnesota Living with Heart Failure (MLwHF) scale. Twenty-five patients were enrolled and 23 (92%) completed 3-month follow-up. Mean age was 60 years (range 35-74), 60% were men, 60% were African-American, and 74% had household income under $15,000 per year. The median reading level was fifth grade with 32% reading at or below the third grade level. Mean knowledge score at baseline was 67% and did not improve after the intervention. The proportion of patients reporting weighing themselves daily increased from 32% at baseline to 100% at 12 weeks. Mean improvement on the MLwHF scale was 9.9 points over the 3-month trial (95% CI: 0.5, 19.2), which corresponds to an improvement in one class on the New York Heart Association heart failure scale. A heart failure disease management program designed specifically for patients with low literacy skills is acceptable and is associated with improvement in self-care behavior and heart failure related symptoms.

Bioluminescence-Based Method for Measuring Assimilable Organic Carbon in Pretreatment Water for Reverse Osmosis Membrane Desalination ▿

PubMed Central

Weinrich, Lauren A.; Schneider, Orren D.; LeChevallier, Mark W.

2011-01-01

A bioluminescence-based assimilable organic carbon (AOC) test was developed for determining the biological growth potential of seawater within the reverse osmosis desalination pretreatment process. The test uses Vibrio harveyi, a marine organism that exhibits constitutive luminescence and is nutritionally robust. AOC was measured in both a pilot plant and a full-scale desalination plant pretreatment. PMID:21148685

A pilot study of mercury liberation and capture from coal-fired power plant fly ash.

PubMed

Li, Jin; Gao, Xiaobing; Goeckner, Bryna; Kollakowsky, Dave; Ramme, Bruce

2005-03-01

The coal-fired electric utility generation industry has been identified as the largest anthropogenic source of mercury (Hg) emissions in the United States. One of the promising techniques for Hg removal from flue gas is activated carbon injection (ACI). The aim of this project was to liberate Hg bound to fly ash and activated carbon after ACI and provide high-quality coal combustion products for use in construction materials. Both bench- and pilot-scale tests were conducted to liberate Hg using a thermal desorption process. The results indicated that up to 90% of the Hg could be liberated from the fly ash or fly-ash-and-activated-carbon mixture using a pilot-scale apparatus (air slide) at 538 degrees C with a very short retention time (less than 1 min). Scanning electron microscope (SEM) evaluation indicated no significant change in fly ash carbon particle morphology following the thermal treatment. Fly ash particles collected in the baghouse of the pilot-scale apparatus were smaller in size than those collected at the exit of the air slide. A similar trend was observed in carbon particles separated from the fly ash using froth flotation. The results of this study suggest a means for power plants to reduce the level of Hg in coal-combustion products and potentially recycle activated carbon while maintaining the resale value of fly ash. This technology is in the process of being patented.

Inflight evaluation of pilot workload measures for rotorcraft research

NASA Technical Reports Server (NTRS)

Shively, Robert J.; Bortolussi, Michael R.; Battiste, Vernol; Hart, Sandra G.; Pepitone, David D.; Matsumoto, Joy Hamerman

1987-01-01

The effectiveness of heart-rate monitoring and the NASA TLX workload rating scale (Hart et al., 1985) in measuring helicopter-pilot workloads is investigated experimentally. Four NASA test pilots flew two 2-h missions each in an SH-3G helicopter, following scenarios with takeoff, hover, cross-country, and landing tasks; pilot performance on the tasks undertaken near the landing area was measured by laser tracking. The results are presented in graphs and discussed in detail, and it is found that the TLX ratings clearly distinguish the flight segments and are well correlated with the performance data. The mean heart rate (measured as interbeat interval) is correlated (r = -0.69) with the TLX workload, but only the standard deviation of the interbeat interval is able to distinguish between flight segments; the correlation between standard deviation and TLX ratings is negative but not significant.

Removals of cryptosporidium parvum oocysts and cryptosporidium-sized polystyrene microspheres from swimming pool water by diatomaceous earth filtration and perlite-sand filtration.

PubMed

Lu, Ping; Amburgey, James E; Hill, Vincent R; Murphy, Jennifer L; Schneeberger, Chandra L; Arrowood, Michael J; Yuan, Tao

2017-06-01

Removal of Cryptosporidium-sized microspheres and Cryptosporidium parvum oocysts from swimming pools was investigated using diatomaceous earth (DE) precoat filtration and perlite-sand filtration. In pilot-scale experiments, microsphere removals of up to 2 log were obtained with 0.7 kg·DE/m 2 at a filtration rate of 5 m/h. A slightly higher microsphere removal (2.3 log) was obtained for these DE-precoated filters when the filtration rate was 3.6 m/h. Additionally, pilot-scale perlite-sand filters achieved greater than 2 log removal when at least 0.37 kg/m 2 of perlite was used compared to 0.1-0.4 log removal without perlite both at a surface loading rate of 37 m/h. Full-scale testing achieved 2.7 log of microspheres and oocysts removal when 0.7 kg·DE/m 2 was used at 3.6 m/h. Removals were significantly decreased by a 15-minute interruption of the flow (without any mechanical agitation) to the DE filter in pilot-scale studies, which was not observed in full-scale filters. Microsphere removals were 2.7 log by perlite-sand filtration in a full-scale swimming pool filter operated at 34 m/h with 0.5 kg/m 2 of perlite. The results demonstrate that either a DE precoat filter or a perlite-sand filter can improve the efficiency of removal of microspheres and oocysts from swimming pools over a standard sand filter under the conditions studied.

Space Shuttle Orbital Drag Parachute Design

NASA Technical Reports Server (NTRS)

Meyerson, Robert E.

2001-01-01

The drag parachute system was added to the Space Shuttle Orbiter's landing deceleration subsystem beginning with flight STS-49 in May 1992. The addition of this subsystem to an existing space vehicle required a detailed set of ground tests and analyses. The aerodynamic design and performance testing of the system consisted of wind tunnel tests, numerical simulations, pilot-in-the-loop simulations, and full-scale testing. This analysis and design resulted in a fully qualified system that is deployed on every flight of the Space Shuttle.

Modified Light Duty AM2 Capability Assessment

DTIC Science & Technology

The Modified Light -Duty AM2 matting was designed specifically for lightweight, remote-piloted aircraft (RPA) applications. An in- depth study was... Ratio (CBR) of 6. To understand the full potential of the Modified Light -Duty AM2, a full- scale evaluation was performed with contingency C-17 and...stir welding for use in fabrication of the lightweight RPA matting in conjunction with a full- scale test on the Modified Light -Duty AM2 matting system

Hanford's Supplemental Treatment Project: Full-Scale Integrated Testing of In-Container-Vitrification and a 10,000-Liter Dryer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Witwer, K.S.; Dysland, E.J.; Garfield, J.S.

2008-07-01

The GeoMelt{sup R} In-Container Vitrification{sup TM} (ICV{sup TM}) process was selected by the U.S. Department of Energy (DOE) in 2004 for further evaluation as the supplemental treatment technology for Hanford's low-activity waste (LAW). Also referred to as 'bulk vitrification', this process combines glass forming minerals, LAW, and chemical amendments; dries the mixture; and then vitrifies the material in a refractory-lined steel container. AMEC Nuclear Ltd. (AMEC) is adapting its GeoMelt ICV{sup TM} technology for this application with technical and analytical support from Pacific Northwest National Laboratory (PNNL). The DVBS project is funded by the DOE Office of River Protection andmore » administered by CH2M HILL Hanford Group, Inc. The Demonstration Bulk Vitrification Project (DBVS) was initiated to engineer, construct, and operate a full-scale bulk vitrification pilot-plant to treat up to 750,000 liters of LAW from Waste Tank 241-S-109 at the DOE Hanford Site. Since the beginning of the DBVS project in 2004, testing has used laboratory, crucible-scale, and engineering-scale equipment to help establish process limitations of selected glass formulations and identify operational issues. Full-scale testing has provided critical design verification of the ICV{sup TM} process before operating the Hanford pilot-plant. In 2007, the project's fifth full-scale test, called FS-38D, (also known as the Integrated Dryer Melter Test, or IDMT,) was performed. This test had three primary objectives: 1) Demonstrate the simultaneous and integrated operation of the ICV{sup TM} melter with a 10,000- liter dryer, 2) Demonstrate the effectiveness of a new feed reformulation and change in process methodology towards reducing the production and migration of molten ionic salts (MIS), and, 3) Demonstrate that an acceptable glass product is produced under these conditions. Testing was performed from August 8 to 17, 2007. Process and analytical results demonstrated that the primary test objectives, along with a dozen supporting objectives, were successfully met. Glass performance exceeded all disposal performance criteria. A previous issue with MIS containment was successfully resolved in FS-38D, and the ICV{sup TM} melter was integrated with a full-scale, 10,000-liter dryer. This paper describes the rationale for performing the test, the purpose and outcome of scale-up tests preceding it, and the performance and outcome of FS-38D. (authors)« less

A Piloted Simulator Evaluation of Transport Aircraft Rudder Pedal Force/Feel Characteristics

NASA Technical Reports Server (NTRS)

Stewart, Eric C.

2008-01-01

A piloted simulation study has been conducted in a fixed-base research simulator to assess the directional handling qualities for various rudder pedal feel characteristics for commercial transport airplanes. That is, the effects of static pedal force at maximum pedal travel, breakout force, and maximum pedal travel on handling qualities were studied. An artificial maneuver with a severe lateral wind shear and requiring runway tracking at an altitude of 50 feet in a crosswind was used to fully exercise the rudder pedals. Twelve active airline pilots voluntarily participated in the study and flew approximately 500 maneuvers. The pilots rated the maneuver performance with various rudder pedal feel characteristics using the Cooper- Harper rating scale. The test matrix had 15 unique combinations of the 3 static pedal feel characteristics. A 10-term, second-order equation for the Cooper-Harper pilot rating as a function of the 3 independent pedal feel parameters was fit to the data. The test matrix utilized a Central Composite Design that is very efficient for fitting an equation of this form. The equation was used to produce contour plots of constant pilot ratings as a function of two of the parameters with the third parameter held constant. These contour plots showed regions of good handling qualities as well as regions of degraded handling qualities. In addition, a numerical equation solver was used to predict the optimum parameter values (those with the lowest pilot rating). Quantitative pilot performance data were also analyzed. This analysis found that the peak values of the cross power spectra of the pedal force and heading angle could be used to quantify the tendency toward directional pilot induced oscillations (PIO). Larger peak values of the cross power spectra were correlated with larger (degraded) Cooper-Harper pilot ratings. Thus, the subjective data (Cooper-Harper pilot ratings) were consistent with the objective data (peak values of the cross power spectra).

Implicit theories of writing and their impact on students' response to a SRSD intervention.

PubMed

Limpo, Teresa; Alves, Rui A

2014-12-01

In the field of intelligence research, it has been shown that some people conceive intelligence as a fixed trait that cannot be changed (entity beliefs), whereas others conceive it as a malleable trait that can be developed (incremental beliefs). What about writing? Do people hold similar implicit theories about the nature of their writing ability? Furthermore, are these beliefs likely to influence students' response to a writing intervention? We aimed to develop a scale to measure students' implicit theories of writing (pilot study) and to test whether these beliefs influence strategy-instruction effectiveness (intervention study). In the pilot and intervention studies participated, respectively, 128 and 192 students (Grades 5-6). Based on existing instruments that measure self-theories of intelligence, we developed the Implicit Theories of Writing (ITW) scale that was tested with the pilot sample. In the intervention study, 109 students received planning instruction based on the self-regulated strategy development model, whereas 83 students received standard writing instruction. Students were evaluated before, in the middle, and after instruction. ITW's validity was supported by piloting results and their successful cross-validation in the intervention study. In this, intervention students wrote longer and better texts than control students. Moreover, latent growth curve modelling showed that the more the intervention students conceived writing as a malleable skill, the more the quality of their texts improved. This research is of educational relevance because it provides a measure to evaluate students' implicit theories of writing and shows their impact on response to intervention. © 2014 The British Psychological Society.

Pilot-scale verification of maximum tolerable hydrodynamic stress for mammalian cell culture.

PubMed

Neunstoecklin, Benjamin; Villiger, Thomas K; Lucas, Eric; Stettler, Matthieu; Broly, Hervé; Morbidelli, Massimo; Soos, Miroslav

2016-04-01

Although several scaling bioreactor models of mammalian cell cultures are suggested and described in the literature, they mostly lack a significant validation at pilot or manufacturing scale. The aim of this study is to validate an oscillating hydrodynamic stress loop system developed earlier by our group for the evaluation of the maximum operating range for stirring, based on a maximum tolerable hydrodynamic stress. A 300-L pilot-scale bioreactor for cultivation of a Sp2/0 cell line was used for this purpose. Prior to cultivations, a stress-sensitive particulate system was applied to determine the stress values generated by stirring and sparging. Pilot-scale data, collected from 7- to 28-Pa maximum stress conditions, were compared with data from classical 3-L cultivations and cultivations from the oscillating stress loop system. Results for the growth behavior, analyzed metabolites, productivity, and product quality showed a dependency on the different environmental stress conditions but not on reactor size. Pilot-scale conditions were very similar to those generated in the oscillating stress loop model confirming its predictive capability, including conditions at the edge of failure.

Production of polyhydroxyalkanoates (PHA) by bacterial consortium from excess sludge fermentation liquid at laboratory and pilot scales.

PubMed

Jia, Qianqian; Xiong, Huilei; Wang, Hui; Shi, Hanchang; Sheng, Xinying; Sun, Run; Chen, Guoqiang

2014-11-01

The generation of polyhydroxyalkanoates (PHA) from excess sludge fermentation liquid (SFL) was studied at lab and pilot scale. A PHA-accumulated bacterial consortium (S-150) was isolated from activated sludge using simulated SFL (S-SFL) contained high concentration volatile fatty acids (VFA) and nitrogen. The maximal PHA content accounted for 59.18% in S-SFL and dropped to 23.47% in actual SFL (L-SFL) of the dry cell weight (DCW) at lab scale. The pilot-scale integrated system comprised an anaerobic fermentation reactor (AFR), a ceramic membrane system (CMS) and a PHA production bio-reactor (PHAR). The PHA content from pilot-scale SFL (P-SFL) finally reached to 59.47% DCW with the maximal PHA yield coefficient (YP/S) of 0.17 g PHA/g COD. The results indicated that VFA-containing SFL was suitable for PHA production. The adverse impact of excess nitrogen and non-VFAs in SFL might be eliminated by pilot-scale domestication, which might resulted in community structure optimization and substrate selective ability improvement of S-150. Copyright © 2014 Elsevier Ltd. All rights reserved.

JPL Activated Carbon Treatment System (ACTS) for sewage

NASA Technical Reports Server (NTRS)

1976-01-01

An Activated Carbon Treatment System (ACTS) was developed for sewage treatment and is being applied to a one-million gallon per day sewage treatment pilot plant in Orange County California. Activities reported include pyrolysis and activation of carbon-sewage sludge, and activated carbon treatment of sewage to meet ocean discharge standards. The ACTS Sewage treatment operations include carbon-sewage treatment, primary and secondary clarifiers, gravity (multi-media) filter, filter press dewatering, flash drying of carbon-sewage filter cake, and sludge pyrolysis and activation. Tests were conducted on a laboratory scale, 10,000 gallon per day demonstration plant and pilot test equipment. Preliminary economic studies are favorable to the ACTS process relative to activated sludge treatment for a 175,000,000 gallon per day sewage treatment plant.

Antioxidative and antimutagenic activities of healthy herbal drinks from Chinese medicinal herbs.

PubMed

Chen, Wenlung; Weng, Yih-Ming; Tseng, Chin-Yin

2003-01-01

Twenty-nine Chinese medicinal herbs and three healthy herbal drinks made of those herbs in a food processing pilot plant were tested for their antioxidative, free radical scavenging, mutagenic and antimutagenic activities. Water extracts of herbs (with few exceptions) and herbal drinks showed free radical scavenging activity. All water extracts of herbs and herbal drinks showed no mutagenicity toward Salmonella typhimurium tester strains TA98 and TA100 used in the Ames mutagenic tests. In the antimutagenic tests, the mutagenic activity of 4-nitroquinoline N-oxide (NQNO) toward S. typhimurium TA98 was markedly inhibited by water extracts of herbs and herbal drinks. Based on the results, it is suggested that the herbal drinks manufactured in pilot-plant scale are safe and can be served as health-promoting drinks for the public.

Comparison of corrosion scales in full and partially replaced ...

EPA Pesticide Factsheets

Preliminary results from scales formed 38 weeks following the LSL replacement simulations revealed differences in scale formations amongst varying water qualities and pipe sequence. Rigs fed with dechlorinated tap water show distinct pH gradients between the galvanic and the background zones. Hydrocerussite and litharge are found both in field and pilot rigs. However, plumbonacrite, massicot, scrutinyite and plattnerite are only present in pipes harvested directly from the field. Laurionite, leadhillite, cerussite and calcite are found in rigs from the pilot. Cerussite is mostly present in the galvanic zones, close to the connection to the Cu pipe. Different types of scales are present in the rigs from the pilot and from the field, suggesting that differences in the formation in the scales and therefore differences in lead release from the pipes. The particulate Pb fraction in water samples is more important in samples from the pilot than from the field, median concentrations are 85X higher in partial LSL and 10X higher in full LSL in the pilot. Lead phosphates are present in the scales from the rigs treated with orthophosphate. Complete results will be obtained by the end of July 2016. The main objective is to compare scales from full and partial LSLs harvested from the field and from a pilot setup fed with water from the same distribution system and subjected to water quality changes.

The use of carbon adsorbents for the removal of perfluoroalkyl acids from potable reuse systems.

PubMed

Inyang, Mandu; Dickenson, Eric R V

2017-10-01

Bench- and pilot-scale sorption tests were used to probe the performance of several biochars at removing perfluoroalkyl acids (PFAA) from field waters, compared to granular activated carbon (GAC). Screening tests using organic matter-free water resulted in hardwood (HWC) (K d  = 41 L g -1 ) and pinewood (PWC) (K d  = 49 L g -1 ) biochars having the highest perfluorooctanoic acid (PFOA) removal performance that was comparable to bituminous coal GAC (K d  = 41 L g -1 ). PWC and HWC had a stronger affinity for PFOA sorbed in Lake Mead surface water (K F  = 11 mg (1-n) L n g -1 ) containing a lower (2 mg L -1 ) dissolved organic carbon (DOC) concentration than in a tertiary-filtered wastewater (K F  = 8 mg (1-n) L n g -1 ) with DOC of 4.9 mg L -1 . A pilot-scale study was performed using three parallel adsorbers (GAC, anthracite, and HWC biochar) treating the same tertiary-filtered wastewater. Compared to HWC, and anthracite, GAC was the most effective in mitigating perfluoropentanoic acid (PFPnA), perfluorohexanoic acid (PHxA), PFOA, perfluorooctane sulfonic acid (PFOS), and DOC (45-67% removed at 4354 bed volumes) followed by HWC, and then anthracite. Based on bench- and pilot-scale results, shorter-chain PFAA [perfluorobutanoic acid (PFBA), PFPnA, or PFHxA] were more difficult to remove with both biochar and GAC than the longer-chain, PFOS and PFOA. Copyright © 2017 Elsevier Ltd. All rights reserved.

Development of Occupational Therapy Proficiency Examinations. Therapist Level, Assistant Level. Final Report.

ERIC Educational Resources Information Center

Professional Examination Service, New York, NY.

Criterion-referenced proficiency examinations have been prepared for entry level occupational therapists and entry level occupational therapy assistants. Item development was based on a task inventory solicited from occupational therapists throughout the country, with six occupational therapists reviewing test development. A small scale pilot test…

The Development and Validation of a Teacher Preparation Program: Follow-Up Survey

ERIC Educational Resources Information Center

Schulte, Laura E.

2008-01-01

Students in my applied advanced statistics course for educational administration doctoral students developed a follow-up survey for teacher preparation programs, using the following scale development processes: adopting a framework; developing items; providing evidence of content validity; conducting a pilot test; and analyzing data. The students…

Assessing Sustainability When Data Availability Limits Real-Time Estimates: Using Near-Time Indicators to Extend Sustainability Metrics

EPA Science Inventory

We produced a scientifically defensible methodology to assess whether a regional system is on a sustainable path. The approach required readily available data, metrics applicable to the relevant scale, and results useful to decision makers. We initiated a pilot project to test ...

In-Situ Air Sparaing: Engineering and Design

DTIC Science & Technology

2008-01-31

Construction Materials. Although PVC casing is commonly used, flexible or rigid polyethylene pipe may be more efficient for certain excavation methods, such as...depth, etc.) Piping insulation/ heat tape installed Piping flushed/cleaned/pressure tested Subsurface as-built equipment...4-4 Figure 4-2 Pilot-Scale Piping and Instrumentation Diagram

Characterizing The Microbial Community In A TCE DNAPL Site: SABRE Column And Field Studies

EPA Science Inventory

The SABRE (Source Area BioREmediation) project is evaluating accelerated anaerobic bioremediation of chlorinated solvents in areas of high concentration, such as DNAPL source areas. In support of a field scale pilot test, column studies were conducted to design the system and ob...

THE DISTRIBUTION, SOLID-PHASE SPECIATION, AND DESORPTION/DISSOLUTION OF AS IN IRON-BASED TREATMENT MEDIA

EPA Science Inventory

Arsenic concentrations (Total Recoverable As by EPA Method 3051) and solid-phase speciation (by X-ray Absorption Near-Edge Spectroscopy-XANES) were assessed as a function of depth through Fe-media beds for two commercially available products from pilot-scale field tests. These re...

THE DISTRIBUTION AND SOLID-PHASE SPECIATION OF AS IN IRON-BASED TREATMENT MEDIA

EPA Science Inventory

Arsenic concentrations (Total Recoverable As by EPA Method 3051) and solid-phase speciation (by X-ray Absorption Near-Edge Spectroscopy-XANES) were assessed as a function of depth through Fe-media beds for two commercially available products from pilot-scale field tests. These r...

FIELD TEST OF CYCLODEXTRIN FOR ENHANCED IN-SITU FLUSHING OF MULTIPLE-COMPONENT IMMISCIBLE ORGANIC LIQUID CONTAMINATION: COMPARISON TO WATER FLUSHING

EPA Science Inventory

A pilot-scale field experiment was conducted to compare the remediation effectiveness of an enhanced-solubilization technique to that of water flushing for removal of multicomponent nonaqueous-phase organic liquid (NAPL) contaminants form a phreatic aquifer. This innovative remed...

Identifying Students Difficulties in Understanding Concepts Pertaining to Cell Water Relations: An Exploratory Study.

ERIC Educational Resources Information Center

Friedler, Y.; And Others

This study identified students' conceptual difficulties in understanding concepts and processes associated with cell water relationships (osmosis), determined possible reasons for these difficulties, and pilot-tested instruments and research strategies for a large scale comprehensive study. Research strategies used included content analysis of…

TEST REPORT FOR THE TRIAL BURN OF DINOSEB IN A PILOT-SCALE INCINERATOR

EPA Science Inventory

The U.S. Environmental Protection Agency (EPA) has determined that the herbicide Dinoseb represents a significant human health hazard. PA estimates that there are approximately 5 million gallons affected by this action. As part of a program by the EPA Office of Research and Devel...

OBSERVATIONS ON THE EFFECT OF PROCESS PARAMETERS ON DIOXIN/FURAN YIELD IN MUNICIPAL WASTE AND COAL SYSTEMS

EPA Science Inventory

Effects of fly ash loading; ash-borne, extractable organics; sulfur dioxide (SO2) and hydrogen chloride concentration; and combustion quality on the formation of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) were evaluated in pilot scale tests simu...

Hybrid Membrane/Absorption Process for Post-combustion CO2 Capture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Shiguang; Shou, S.; Pyrzynski, Travis

2013-12-31

This report summarizes scientific/technical progress made for bench-scale membrane contactor technology for post-combustion CO2 capture from DOE Contract No. DE-FE-0004787. Budget Period 1 (BP1) membrane absorber, Budget Period 2 (BP2) membrane desorber and Budget Period 3 (BP3) integrated system and field testing studies have been completed successfully and met or exceeded the technical targets (≥ 90% CO2 removal and CO2 purity of 97% in one membrane stage). Significant breakthroughs are summarized below: BP1 research: The feasibility of utilizing the poly (ether ether ketone), PEEK, based hollow fiber contractor (HFC) in combination with chemical solvents to separate and capture at leastmore » 90% of the CO2 from simulated flue gases has been successfully established. Excellent progress has been made as we have achieved the BP1 goal: ≥ 1,000 membrane intrinsic CO2 permeance, ≥ 90% CO2 removal in one stage, ≤ 2 psi gas side pressure drop, and ≥ 1 (sec)-1 mass transfer coefficient. Initial test results also show that the CO2 capture performance, using activated Methyl Diethanol Amine (aMDEA) solvent, was not affected by flue gas contaminants O2 (~3%), NO2 (66 ppmv), and SO2 (145 ppmv). BP2 research: The feasibility of utilizing the PEEK HFC for CO2-loaded solvent regeneration has been successfully established High CO2 stripping flux, one order of magnitude higher than CO2 absorption flux, have been achieved. Refined economic evaluation based on BP1 membrane absorber and BP2 membrane desorber laboratory test data indicate that the CO2 capture costs are 36% lower than DOE’s benchmark amine absorption technology. BP3 research: A bench-scale system utilizing a membrane absorber and desorber was integrated into a continuous CO2 capture process using contactors containing 10 to 20 ft2 of membrane area. The integrated process operation was stable through a 100-hour laboratory test, utilizing a simulated flue gas stream. Greater than 90% CO2 capture combined with 97% CO2 product purity was achieved throughout the test. Membrane contactor modules have been scaled from bench scale 2-inch diameter by 12-inch long (20 ft2 membrane surface area) modules to 4-inch diameter by 60-inch long pilot scale modules (165 ft2 membrane surface area). Pilot scale modules were tested in an integrated absorption/regeneration system for CO2 capture field tests at a coal-fired power plant (Midwest Generation’s Will County Station located in Romeoville, IL). Absorption and regeneration contactors were constructed utilizing high performance super-hydrophobic, nano-porous PEEK membranes with CO2 gas permeance of 2,000 GPU and a 1,000 GPU, respectively. Field tests using aMDEA solvent achieved greater than 90% CO2 removal in a single stage. The absorption mass transfer coefficient was 1.2 (sec)-1, exceeding the initial target of 1.0 (sec)-1. This mass transfer coefficient is over one order of magnitude greater than that of conventional gas/liquid contacting equipment. The economic evaluation based on field tests data indicates that the CO2 capture cost associated with membrane contactor technology is $54.69 (Yr 2011$)/tonne of CO2 captured when using aMDEA as a solvent. It is projected that the DOE’s 2025 cost goal of $40 (Yr 2011$)/tonne of CO2 captured can be met by decreasing membrane module cost and by utilizing advanced CO2 capture solvents. In the second stage of the field test, an advanced solvent, Hitachi’s H3-1 was utilized. The use of H3-1 solvent increased mass transfer coefficient by 17% as compared to aMDEA solvent. The high mass transfer coefficient of H3-1 solvent combined with much more favorable solvent regeneration requirements, indicate that the projected savings achievable with membrane contactor process can be further improved. H3-1 solvent will be used in the next pilot-scale development phase. The integrated absorption/regeneration process design and high performance membrane contactors developed in the current bench-scale program will be used as the base technology for future pilot-scale development.« less

Applicability of the mixture of bituminous coal and anthracite to conventional pulverized coal firing boiler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takano, Shin-Ichi; Kiga, Takashi; Miyamae, Shigehiro

1994-12-31

In some future, it is expected for Japanese power stations to be hard to get a high-grade coal like a bituminous coal. We conducted therefore pilot scale tests of pulverized blends of bituminous coal and anthracite using a 1.2MWt tunnel furnace in order to evaluate the applicability of the blends of bituminous coal and anthracite to conventional pulverized coal firing boilers. One kind of bituminous coal and two kinds of anthracite, one was of low ash content and another was of high ash content, were prepared for the test. Previously to pilot scale tests, coal properties and ash properties ofmore » the blends of bituminous coal and anthracite were analyzed to estimate the characteristics of combustion, ash deposition, and so on. In the test, we investigated the combustion efficiency, NOx emission, characteristics of ignition stability and grindability changing the blend rate of anthracite. Results of our study indicated that the critical restrictions on the blending rate of anthracite were unburnt carbon in fly ash and NOx emission as for coals tested. The acceptable limitation on blending rate of anthracite was 10 and 20%, respectively for two kinds of conventional pulverized coal fired boiler. Concerning to the grindability, it became worse with increasing the blending rate of anthracite from grindability test using a roller mill, while it became better estimating from HGI.« less

[Emotion Recognition in Patients with Peripheral Facial Paralysis - A Pilot Study].

PubMed

Konnerth, V; Mohr, G; von Piekartz, H

2016-02-01

The perception of emotions is an important component in enabling human beings to social interaction in everyday life. Thus, the ability to recognize the emotions of the other one's mime is a key prerequisite for this. The following study aimed at evaluating the ability of subjects with 'peripheral facial paresis' to perceive emotions in healthy individuals. A pilot study was conducted in which 13 people with 'peripheral facial paresis' participated. This assessment included the 'Facially Expressed Emotion Labeling-Test' (FEEL-Test), the 'Facial-Laterality-Recognition Test' (FLR-Test) and the 'Toronto-Alexithymie-Scale 26' (TAS 26). The results were compared with data of healthy people from other studies. In contrast to healthy patients, the subjects with 'facial paresis' show more difficulties in recognizing basic emotions; however the results are not significant. The participants show a significant lower level of speed (right/left: p<0.001) concerning the perception of facial laterality compared to healthy people. With regard to the alexithymia, the tested group reveals significantly higher results (p<0.001) compared to the unimpaired people. The present pilot study does not prove any impact on this specific patient group's ability to recognize emotions and facial laterality. For future studies the research question should be verified in a larger sample size. © Georg Thieme Verlag KG Stuttgart · New York.

PEROXIDE DESTRUCTION TESTING FOR THE 200 AREA EFFLUENT TREATMENT FACILITY

DOE Office of Scientific and Technical Information (OSTI.GOV)

HALGREN DL

2010-03-12

The hydrogen peroxide decomposer columns at the 200 Area Effluent Treatment Facility (ETF) have been taken out of service due to ongoing problems with particulate fines and poor destruction performance from the granular activated carbon (GAC) used in the columns. An alternative search was initiated and led to bench scale testing and then pilot scale testing. Based on the bench scale testing three manganese dioxide based catalysts were evaluated in the peroxide destruction pilot column installed at the 300 Area Treated Effluent Disposal Facility. The ten inch diameter, nine foot tall, clear polyvinyl chloride (PVC) column allowed for the samemore » six foot catalyst bed depth as is in the existing ETF system. The flow rate to the column was controlled to evaluate the performance at the same superficial velocity (gpm/ft{sup 2}) as the full scale design flow and normal process flow. Each catalyst was evaluated on peroxide destruction performance and particulate fines capacity and carryover. Peroxide destruction was measured by hydrogen peroxide concentration analysis of samples taken before and after the column. The presence of fines in the column headspace and the discharge from carryover was generally assessed by visual observation. All three catalysts met the peroxide destruction criteria by achieving hydrogen peroxide discharge concentrations of less than 0.5 mg/L at the design flow with inlet peroxide concentrations greater than 100 mg/L. The Sud-Chemie T-2525 catalyst was markedly better in the minimization of fines and particle carryover. It is anticipated the T-2525 can be installed as a direct replacement for the GAC in the peroxide decomposer columns. Based on the results of the peroxide method development work the recommendation is to purchase the T-2525 catalyst and initially load one of the ETF decomposer columns for full scale testing.« less

Performance of a pilot-scale continuous flow microbial electrolysis cell fed winery wastewater.

PubMed

Cusick, Roland D; Bryan, Bill; Parker, Denny S; Merrill, Matthew D; Mehanna, Maha; Kiely, Patrick D; Liu, Guangli; Logan, Bruce E

2011-03-01

A pilot-scale (1,000 L) continuous flow microbial electrolysis cell was constructed and tested for current generation and COD removal with winery wastewater. The reactor contained 144 electrode pairs in 24 modules. Enrichment of an exoelectrogenic biofilm required ~60 days, which is longer than typically needed for laboratory reactors. Current generation was enhanced by ensuring adequate organic volatile fatty acid content (VFA/SCOD ≥ 0.5) and by raising the wastewater temperature (31 ± 1°C). Once enriched, SCOD removal (62 ± 20%) was consistent at a hydraulic retention time of 1 day (applied voltage of 0.9 V). Current generation reached a maximum of 7.4 A/m(3) by the planned end of the test (after 100 days). Gas production reached a maximum of 0.19 ± 0.04 L/L/day, although most of the product gas was converted to methane (86 ± 6%). In order to increase hydrogen recovery in future tests, better methods will be needed to isolate hydrogen gas produced at the cathode. These results show that inoculation and enrichment procedures are critical to the initial success of larger-scale systems. Acetate amendments, warmer temperatures, and pH control during startup were found to be critical for proper enrichment of exoelectrogenic biofilms and improved reactor performance.

A human factors curriculum for surgical clerkship students.

PubMed

Cahan, Mitchell A; Larkin, Anne C; Starr, Susan; Wellman, Scott; Haley, Heather-Lyn; Sullivan, Kate; Shah, Shimul; Hirsh, Michael; Litwin, Demetrius; Quirk, Mark

2010-12-01

Early introduction of a full-day human factors training experience into the surgical clerkship curriculum will teach effective communication skills and strategies to gain professional satisfaction from a career in surgery. In pilot 1, which took place between July 1, 2007, and December 31, 2008, 50 students received training and 50 did not; all received testing at the end of the rotation for comparison of control vs intervention group performance. In pilot 2, a total of 50 students were trained and received testing before and after rotation to examine individual change over time. University of Massachusetts Medical School. A total of 148 third-year medical students in required 12-week surgical clerkship rotations. Full-day training with lecture and small-group exercises, cotaught by surgeons and educators, with focus on empathetic communication, time management, and teamwork skills. Empathetic communication skill, teamwork, and patient safety attitudes and self-reported use of time management strategies. Empathy scores were not higher for trained vs untrained groups in pilot 1 but improved from 2.32 to 3.45 on a 5-point scale (P < .001) in pilot 2. Students also were more likely to ask for the nurse's perspective and to seek agreement on an action plan after team communication training (pilot 1, f = 7.52, P = .007; pilot 2, t = 2.65, P = .01). Results were mixed for work-life balance, with some trained groups scoring significantly lower than untrained groups in pilot 1 and no significant improvement shown in pilot 2. The significant increase in student-patient communication scores suggests that a brief focused presentation followed by simulation of difficult patient encounters can be successful. A video demonstration can improve interdisciplinary teamwork.

Exploratory piloted simulator study of the effects of winglets on handling qualities of a representative agricultural airplane

NASA Technical Reports Server (NTRS)

Ogburn, M. E.; Brown, P. W.

1980-01-01

The effects on handling qualities of adding winglets to a representative agricultural aircraft configuration during swath-run maneuvering were evaluated. Aerodynamic data used in the simulation were based on low-speed wind tunnel tests of a full scale airplane and a subscale model. The Cooper-Harper handling qualities rating scale, supplementary pilot comments, and pilot vehicle performance data were used to describe the handling qualities of the airplane with the different wing-tip configurations. Results showed that the lateral-directional handling qualities of the airplane were greatly affected by the application of winglets and winglet cant angle. The airplane with winglets canted out 20 deg exhibited severely degraded lateral directional handling qualities in comparison to the basic airplane. When the winglets were canted inward 10 deg, the flying qualities of the configuration were markedly improved over those of the winglet-canted-out configuration or the basic configuration without winglets, indicating that proper tailoring of the winglet design may afford a potential benefit in the area of handling qualities.

A Synergistic Combination of Advanced Separation and Chemical Scale Inhibitor Technologies for Efficient Use of Imparied Water As Cooling Water in Coal-based Power Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jasbir Gill

2010-08-30

Nalco Company is partnering with Argonne National Laboratory (ANL) in this project to jointly develop advanced scale control technologies that will provide cost-effective solutions for coal-based power plants to operate recirculating cooling water systems at high cycles using impaired waters. The overall approach is to use combinations of novel membrane separations and scale inhibitor technologies that will work synergistically, with membrane separations reducing the scaling potential of the cooling water and scale inhibitors extending the safe operating range of the cooling water system. The project started on March 31, 2006 and ended in August 30, 2010. The project was amore » multiyear, multi-phase project with laboratory research and development as well as a small pilot-scale field demonstration. In Phase 1 (Technical Targets and Proof of Concept), the objectives were to establish quantitative technical targets and develop calcite and silica scale inhibitor chemistries for high stress conditions. Additional Phase I work included bench-scale testing to determine the feasibility of two membrane separation technologies (electrodialysis ED and electrode-ionization EDI) for scale minimization. In Phase 2 (Technology Development and Integration), the objectives were to develop additional novel scale inhibitor chemistries, develop selected separation processes, and optimize the integration of the technology components at the laboratory scale. Phase 3 (Technology Validation) validated the integrated system's performance with a pilot-scale demonstration. During Phase 1, Initial evaluations of impaired water characteristics focused on produced waters and reclaimed municipal wastewater effluents. Literature and new data were collected and evaluated. Characteristics of produced waters vary significantly from one site to another, whereas reclaimed municipal wastewater effluents have relatively more uniform characteristics. Assessment to date confirmed that calcite and silica/silicate are two common potential cycle-limiting minerals for using impaired waters. For produced waters, barium sulfate and calcium sulfate are two additional potential cycle-limiting minerals. For reclaimed municipal wastewater effluents, calcium phosphate scaling can be an issue, especially in the co-presence of high silica. Computational assessment, using a vast amount of Nalco's field data from coal fired power plants, showed that the limited use and reuse of impaired waters is due to the formation of deposit caused by the presence of iron, high hardness, high silica and high alkalinity in the water. Appropriate and cost-effective inhibitors were identified and developed - LL99B0 for calcite and gypsum inhibition and TX-15060 for silica inhibition. Nalco's existing dispersants HSP-1 and HSP-2 has excellent efficacy for dispersing Fe and Mn. ED and EDI were bench-scale tested by the CRADA partner Argonne National Laboratory for hardness, alkalinity and silica removal from synthetic make-up water and then cycled cooling water. Both systems showed low power consumption and 98-99% salt removal, however, the EDI system required 25-30% less power for silica removal. For Phase 2, the EDI system's performance was optimized and the length of time between clean-in-place (CIP) increased by varying the wafer composition and membrane configuration. The enhanced EDI system could remove 88% of the hardness and 99% of the alkalinity with a processing flux of 19.2 gal/hr/m{sup 2} and a power consumption of 0.54 kWh/100 gal water. Bench tests to screen alternative silica/silicate scale inhibitor chemistries have begun. The silica/silicate control approaches using chemical inhibitors include inhibition of silicic acid polymerization and dispersion of silica/silicate crystals. Tests were conducted with an initial silica concentration of 290-300 mg/L as SiO{sub 2} at pH 7 and room temperature. A proprietary new chemistry was found to be promising, compared with a current commercial product commonly used for silica/silicate control. Additional pilot cooling tower testing confirmed the bench study. We also developed a molecule to inhibit calcium carbonate precipitation and calcium sulfate precipitation at high supersaturations. During Phase 3, a long-term test of the EDI system and scale inhibitors was done at Nalco's cooling tower water testing facility, producing 850 gallons of high purity water (90+% salt removal) at a rate of 220 L/day. The EDI system's performance was stable when the salt concentration in the concentrate compartment (i.e. the EDI waste stream) was controlled and a CIP was done after every 48 hours of operation time. A combination of EDI and scale inhibitors completely eliminated blowdown discharge from the Pilot cooling Tower. The only water-consumption came from evaporation, CIP and EDI concentrate. Silica Inhibitor was evaluated in the field at a western coal fired power plant.« less

Literature review: Assessment of DWPF melter and melter off-gas system lifetime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reigel, M. M.

2015-07-30

A glass melter for use in processing radioactive waste is a challenging environment for the materials of construction (MOC) resulting from a combination of high temperatures, chemical attack, and erosion/corrosion; therefore, highly engineered materials must be selected for this application. The focus of this report is to review the testing and evaluations used in the selection of the Defense Waste Processing Facility (DWPF), glass contact MOC specifically the Monofrax ® K-3 refractory and Inconel ® 690 alloy. The degradation or corrosion mechanisms of these materials during pilot scale testing and in-service operation were analyzed over a range of oxidizing andmore » reducing flowsheets; however, DWPF has primarily processed a reducing flowsheet (i.e., Fe 2+/ΣFe of 0.09 to 0.33) since the start of radioactive operations. This report also discusses the materials selection for the DWPF off-gas system and the corrosion evaluation of these materials during pilot scale testing and non-radioactive operations of DWPF Melter #1. Inspection of the off-gas components has not been performed during radioactive operations with the exception of maintenance because of plugging.« less

Literature review: Assessment of DWPF melter and melter off-gas system lifetime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reigel, M.

2015-07-30

A glass melter for use in processing radioactive waste is a challenging environment for the materials of construction (MOC) resulting from a combination of high temperatures, chemical attack, and erosion/corrosion; therefore, highly engineered materials must be selected for this application. The focus of this report is to review the testing and evaluations used in the selection of the Defense Waste Processing Facility (DWPF), glass contact MOC specifically the Monofrax® K-3 refractory and Inconel® 690 alloy. The degradation or corrosion mechanisms of these materials during pilot scale testing and in-service operation were analyzed over a range of oxidizing and reducing flowsheets;more » however, DWPF has primarily processed a reducing flowsheet (i.e., Fe 2+/ΣFe of 0.09 to 0.33) since the start of radioactive operations. This report also discusses the materials selection for the DWPF off-gas system and the corrosion evaluation of these materials during pilot scale testing and non-radioactive operations of DWPF Melter #1. Inspection of the off-gas components has not been performed during radioactive operations with the exception of maintenance because of plugging.« less

Pilot- and bench-scale testing of faecal indicator bacteria survival in marine beach sand near point sources

USGS Publications Warehouse

Mika, K.B.; Imamura, G.; Chang, C.; Conway, V.; Fernandez, G.; Griffith, J.F.; Kampalath, R.A.; Lee, C.M.; Lin, C.-C.; Moreno, R.; Thompson, S.; Whitman, R.L.; Jay, J.A.

2009-01-01

Aim: Factors affecting faecal indicator bacteria (FIB) and pathogen survival/persistence in sand remain largely unstudied. This work elucidates how biological and physical factors affect die-off in beach sand following sewage spills. Methods and Results: Solar disinfection with mechanical mixing was pilot-tested as a disinfection procedure after a large sewage spill in Los Angeles. Effects of solar exposure, mechanical mixing, predation and/or competition, season, and moisture were tested at bench scale. First-order decay constants for Escherichia coli ranged between -0??23 and -1??02 per day, and for enterococci between -0??5 and -1??0 per day. Desiccation was a dominant factor for E. coli but not enterococci inactivation. Effects of season were investigated through a comparison of experimental results from winter, spring, and fall. Conclusions: Moisture was the dominant factor controlling E. coli inactivation kinetics. Initial microbial community and sand temperature were also important factors. Mechanical mixing, common in beach grooming, did not consistently reduce bacterial levels. Significance and Impact of the Study: Inactivation rates are mainly dependent on moisture and high sand temperature. Chlorination was an effective disinfection treatment in sand microcosms inoculated with raw influent. ?? 2009 The Society for Applied Microbiology.

The development and psychometric testing of East Asian Acculturation Scale among Asian immigrant women in Taiwan.

PubMed

Kuo, Shu-Fen; Chang, Wen-Yin; Chang, Lu-I; Chou, Yu-Hua; Chen, Ching-Min

2013-01-01

This is a report of development and psychometric testing of the East Asian Acculturation Measure-Chinese version (EAAM-C) scale. An instrument validation design with a cross-sectional survey was conducted. The process was carried in two phases. In Phase 1, Barry's East Asian Acculturation Measure was translated and back translated to evaluate its content, face validity, and feasibility validity. In Phase 2, the 16-item EAAM-C was pilot-tested among 485 female immigrants for test-retest reliability, internal consistency, theoretically-supported construct validity and concurrent validity. The pilot work and the survey results indicated the tools possessed adequate content and face validity. The Cronbach's Alphas for the EAAM-C was 0.72, and 0.76-0.79 for its subscales, and the correlation of test-retest reliability (at 3 weeks) was 0.75. After dropping one item, four theoretically-supported factors which explained 61.82% of the variance were abstracted using exploratory factor analysis: assimilation, integration, separation, and marginalization. Based on the underlying four-factor theoretical structures of the EAAM, the confirmatory factor analysis of the EAAM-C was further examined. The analysis revealed that the four-factor model was an acceptable fit for the data which demonstrated adequate finding in its construct validity. These factors were inter-correlated, and showed statistically significant correlation with the Chinese Health Questionnaire, indicating adequate concurrent validity. The scale shows acceptable validity and consistency, and suggests that immigrant acculturation is a complex construct. This quick evaluation instrument can be applied to assess clients' acculturation and in further developing certain interventions to improve their health.

SUPERFUND TREATABILITY CLEARINGHOUSE: BENGART AND MEMEL (BENCH-SCALE), GULFPORT (BENCH AND PILOT-SCALE), MONTANA POLE (BENCH-SCALE), AND WESTERN PROCESSING (BENCH-SCALE) TREATABILITY STUDIES

EPA Science Inventory

This document presents summary data on the results of various treatability studies (bench and pilot scale), conducted at three different sites where soils were contaminated with dioxins or PCBs. The synopsis is meant to show rough performance levels under a variety of differen...

Granular activated carbon adsorption of MIB in the presence of dissolved organic matter.

PubMed

Summers, R Scott; Kim, Soo Myung; Shimabuku, Kyle; Chae, Seon-Ha; Corwin, Christopher J

2013-06-15

Based on the results of over twenty laboratory granular activated carbon (GAC) column runs, models were developed and utilized for the prediction of 2-methylisoborneol (MIB) breakthrough behavior at parts per trillion levels and verified with pilot-scale data. The influent MIB concentration was found not to impact the concentration normalized breakthrough. Increasing influent background dissolved organic matter (DOM) concentration was found to systematically decrease the GAC adsorption capacity for MIB. A series of empirical models were developed that related the throughput in bed volumes for a range of MIB breakthrough targets to the influent DOM concentration. The proportional diffusivity (PD) designed rapid small-scale column test (RSSCT) could be directly used to scale-up MIB breakthrough performance below 15% breakthrough. The empirical model to predict the throughput to 50% breakthrough based on the influent DOM concentration served as input to the pore diffusion model (PDM) and well-predicted the MIB breakthrough performance below a 50% breakthrough. The PDM predictions of throughput to 10% breakthrough well simulated the PD-RSSCT and pilot-scale 10% MIB breakthrough. Copyright © 2013 Elsevier Ltd. All rights reserved.

Urdu translation and validation of shorter version of Positive Affect and Negative Affect Schedule (PANAS) on Pakistani bank employees.

PubMed

Akhter, Noreen

2017-10-01

To translate, adapt and validate shorter version of positive affect and negative affect scale on Pakistani corporate employees. This cross-sectional study was conducted in the twin cities of Islamabad and Rawalpindi from October 2014 to December 2015. The study was completed into two independent parts. In part one, the scale was translated by forward translation. Then it was pilot-tested and administered on customer services employees from commercial banks and the telecommunication sector. Data of the pilot study was analysed by using exploratory factor analysis to extract the initial factor of positive affect and negative affect scale. Part two comprised the main study. Commercial bank employees were included in the sample using convenient sampling technique. Data of the main study was analysed using confirmatory factor analysis in order to establish construct validity of positive affect and negative affect scale. There were145 participants in the first part of the study and 495 in the second. Results of confirmatory factor analysis confirmed the two-factor structure of positive affect and negative affect scale suggesting that the scale has two distinct domains, i.e. positive affect and negative affect. The shorter version of positive affect and negative affect scale was found to be a valid and reliable measure.

Implementation of Pilot Protection System for Large Scale Distribution System like The Future Renewable Electric Energy Distribution Management Project

NASA Astrophysics Data System (ADS)

Iigaya, Kiyohito

A robust, fast and accurate protection system based on pilot protection concept was developed previously and a few alterations in that algorithm were made to make it faster and more reliable and then was applied to smart distribution grids to verify the results for it. The new 10 sample window method was adapted into the pilot protection program and its performance for the test bed system operation was tabulated. Following that the system comparison between the hardware results for the same algorithm and the simulation results were compared. The development of the dual slope percentage differential method, its comparison with the 10 sample average window pilot protection system and the effects of CT saturation on the pilot protection system are also shown in this thesis. The implementation of the 10 sample average window pilot protection system is done to multiple distribution grids like Green Hub v4.3, IEEE 34, LSSS loop and modified LSSS loop. Case studies of these multi-terminal model are presented, and the results are also shown in this thesis. The result obtained shows that the new algorithm for the previously proposed protection system successfully identifies fault on the test bed and the results for both hardware and software simulations match and the response time is approximately less than quarter of a cycle which is fast as compared to the present commercial protection system and satisfies the FREEDM system requirement.

A status report on NASA general aviation stall/spin flight testing

NASA Technical Reports Server (NTRS)

Patton, J. M., Jr.

1980-01-01

The NASA Langley Research Center has undertaken a comprehensive program involving spin tunnel, static and rotary balance wind tunnel, full-scale wind tunnel, free flight radio control model, flight simulation, and full-scale testing. Work underway includes aerodynamic definition of various configurations at high angles of attack, testing of stall and spin prevention concepts, definition of spin and spin recovery characteristics, and development of test techniques and emergency spin recovery systems. This paper presents some interesting results to date for the first aircraft (low-wing, single-engine) in the program, in the areas of tail design, wing leading edge design, mass distribution, center of gravity location, and small airframe changes, with associated pilot observations. The design philosophy of the spin recovery parachute system is discussed in addition to test techniques.

A Pilot-Scale Evaluation of a New Technology to Control NO(x) Emissions from Boilers at KSC: Hydrogen Peroxide Injection into Boiler Flue Gases Followed by Wet Scrubbing of Acid Gases

NASA Technical Reports Server (NTRS)

Cooper, C. David

1997-01-01

Emissions of nitrogen oxides NO(x) are a significant problem in the United States. NO(x) are formed in any combustion process, therefore it is not surprising that NO(x) are emitted from the boilers at KSC. Research at UCF has shown (in the laboratory) that injecting H2O2 into hot simulated flue gases can oxidize the NO and NO2 to their acid gas forms, HNO2 and HNO3, respectively. These acid gases are much more water soluble than their counterparts, and theoretically can be removed easily by wet scrubbing. This technology was of interest to NASA, both for their boilers at KSC, and for their combustion sources elsewhere. However, it was necessary to field test the technology and to provide pilot-scale data to aid in design of full-scale facilities. Hence this project was initiated in May of 1996.

APOLLO SOYUZ TEST PROJECT [ASTP] SPACECRAFT FULL SCALE MODEL

NASA Technical Reports Server (NTRS)

1975-01-01

Model of docked Apollo and Soyuz spacecraft in the foreground and skylight in the Vehicle Assembly Building high bay frame the second stage of the Saturn 1B booster that will launch the United States ASTP mission as a crane raises it prior to its mating with the Saturn 1B first stage. Mating of the Saturn 1B first and second stages was completed this morning. The U. S. ASTP launch with mission commander Thomas Stafford, command module pilot Vance Brand and docking module pilot Donald Slayton is scheduled at 3:50 p.m. EDT July 15.

Recovery Act. Demonstration of a Pilot Integrated Biorefinery for the Efficient, Direct Conversion of Biomass to Diesel Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schuetzle, Dennis; Tamblyn, Greg; Caldwell, Matt

2015-05-12

The Renewable Energy Institute International, in collaboration with Greyrock Energy and Red Lion Bio-Energy (RLB) has successfully demonstrated operation of a 25 ton per day (tpd) nameplate capacity, pilot, pre-commercial-scale integrated biorefinery (IBR) plant for the direct production of premium, “drop-in”, synthetic fuels from agriculture and forest waste feedstocks using next-generation thermochemical and catalytic conversion technologies. The IBR plant was built and tested at the Energy Center, which is located in the University of Toledo Medical Campus in Toledo, Ohio.

RELATIONSHIPS BETWEEN LABORATORY AND PILOT-SCALE COMBUSTION OF SOME CHLORINATED HYDROCARBONS

EPA Science Inventory

Factors governing the occurence of trace amounts of residual organic substance emmissions (ROSEs) in full-scale incierators are not fully understood. Pilot-scale spray combustion expereiments involving some liquid chlorinated hydrocarbons (CHCs) and their dilute mixtures with hy...

Evaluation of Electronic Formats of the NASA Task Load Index

NASA Technical Reports Server (NTRS)

Trujillo, Anna C.

2011-01-01

Paper questionnaires are being replaced by electronic questionnaires. The primary objective of this research was to determine whether electronic formats of paper questionnaires change subjects ratings and, if so, how the ratings changed. Results indicated that there were no statistically significant differences in self-assessment of workload when using the electronic replica or the paper format of the NASA-TLX scale. Variations of the electronic formats were tested to enforce structure to the TLX scale. Respondents had more consistent ratings with these alternative formats of the NASA-TLX. Non-pilots, in general, had lower workload ratings than pilots. The time to input the rating was the fastest for the electronic facsimile and random title formats. Also subjects preferred the electronic formats and thought these formats were easier to use. Therefore, moving questionnaires from paper to electronic media could change respondents' answers.

Cognitive behavioral therapy for compulsive buying disorder.

PubMed

Mitchell, James E; Burgard, Melissa; Faber, Ron; Crosby, Ross D; de Zwaan, Martina

2006-12-01

To our knowledge, no psychotherapy treatment studies for compulsive buying have been published. The authors conducted a pilot trial comparing the efficacy of a group cognitive behavioral intervention designed for the treatment of compulsive buying to a waiting list control. Twenty-eight subjects were assigned to receive active treatment and 11 to the waiting list control group. The results at the end of treatment showed significant advantages for cognitive behavioral therapy (CBT) over the waiting list in reductions in the number of compulsive buying episodes and time spent buying, as well as scores on the Yale-Brown Obsessive Compulsive Scale--Shopping Version and the Compulsive Buying Scale. Improvement was well-maintained at 6-month follow-up. The pilot data suggests that a cognitive behavioral intervention can be quite effective in the treatment of compulsive buying disorder. This model requires further testing.

Letter report on PCT/Monolith glass ceramic corrosion tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, Charles L.

2015-09-24

The Savannah River National Laboratory (SRNL) is collaborating with personnel from Pacific Northwest National Laboratory (PNNL) to study advanced waste form glass ceramics for immobilization of waste from Used Nuclear Fuel (UNF) separations processes. The glass ceramic waste forms take advantage of both crystalline and glassy phases where ‘troublesome’ elements (e.g., low solubility in glass or very long-lived) partition to highly durable ceramic phases with the remainder of elements residing in the glassy phase. The ceramic phases are tailored to create certain minerals or unique crystalline structures that can host the radionuclides by binding them in their specific crystalline networkmore » while not adversely impacting the residual glass network (Crum et al., 2011). Glass ceramics have been demonstrated using a scaled melter test performed in a pilot scale (1/4 scale) cold crucible induction melter (CCIM) (Crum et al., 2014; Maio et al., 2015). This report summarizes recent results from both Phase I and Phase II bench scale tests involving crucible fabrication and corrosion testing of glass ceramics using the Product Consistency Test (PCT). Preliminary results from both Phase I and Phase II bench scale tests involving statistically designed matrices have previously been reported (Crawford, 2013; Crawford, 2014).« less

Development and pilot testing of an integrated, web-based self-management program for irritable bowel syndrome (IBS).

PubMed

Dorn, S D; Palsson, O S; Woldeghebriel, M; Fowler, B; McCoy, R; Weinberger, M; Drossman, D A

2015-01-01

Although essential, many medical practices are unable to adequately support irritable bowel syndrome (IBS) patient self-management. Web-based programs can help overcome these barriers. We developed, assessed, and refined an integrated IBS self-management program (IBS Self-care). We then conducted a 12-week pilot test to assess program utilization, evaluate its association with patients' self-efficacy and quality of life, and collect qualitative feedback to improve the program. 40 subjects with generally mild IBS were recruited via the Internet to participate in a 12-week pilot study. Subjects found the website easy to use (93%) and personally relevant (95%), and 90% would recommend it to a friend. Self-rated IBS knowledge increased from an average of 47.1 on a 100-point VAS scale (SD 22.1) at baseline to 77.4 (SD: 12.4) at week 12 (p < 0.0001). There were no significant changes in patient self-efficacy (Patient Activation Measure) or quality of life (IBS -Quality of Life Scale). The IBS Self-Care program was well received by users who after 12 weeks reported improved knowledge about IBS, but no significant changes in self-efficacy or quality of life. If applied to the right population, this low cost solution can overcome some of the deficiencies of medical care and empower individuals to better manage their own IBS. © 2014 John Wiley & Sons Ltd.

PILOT-SCALE REMOVAL OF FLUORIDE FROM LEGACY PLUTONIUM MATERIALS USING VACUUM SALT DISTILLATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R. A.; Pak, D. J.

2012-09-11

Between September 2009 and January 2011, the Savannah River National Laboratory (SRNL) and HB-Line designed, developed, tested, and successfully deployed a system for the distillation of chloride salts. In 2011, SRNL adapted the technology for the removal of fluoride from fluoride-bearing salts. The method involved an in situ reaction between potassium hydroxide (KOH) and the fluoride salt to yield potassium fluoride (KF) and the corresponding oxide. The KF and excess KOH can be distilled below 1000{deg}C using vacuum salt distillation (VSD). The apparatus for vacuum distillation contains a zone heated by a furnace and a zone actively cooled using eithermore » recirculated water or compressed air. During a vacuum distillation operation, a sample boat containing the feed material is placed into the apparatus while it is cool, and the system is sealed. The system is evacuated using a vacuum pump. Once a sufficient vacuum is attaned, heating begins. Volatile salts distill from the heated zone to the cooled zone where they condense, leaving behind the non-volatile material in the feed boat. Studies discussed in this report were performed involving the use of non-radioactive simulants in small-scale and pilot-scale systems as well as radioactive testing of a small-scale system with plutonium-bearing materials. Aspects of interest include removable liner design considerations, boat materials, in-line moisture absorption, and salt deposition.« less

PILOT: optical performance and end-to-end characterisation

NASA Astrophysics Data System (ADS)

Longval, Y.; Misawa, R.; Ade, P.; André, Y.; de Bernardis, P.; Bousquet, F.; Bouzit, M.; Buttice, V.; Charra, M.; Crane, B.; Dubois, J. P.; Engel, C.; Griffin, M.; Hargrave, P.; Leriche, B.; Maestre, S.; Marty, C.; Marty, W.; Masi, S.; Mot, B.; Narbonne, J.; Pajot, F.; Pisano, G.; Ponthieu, N.; Ristorcelli, I.; Rodriguez, L.; Roudil, G.; Simonella, O.; Salatino, M.; Savini, G.; Tucker, C.; Bernard, J.-P.

2017-11-01

PILOT (Polarized Instrument for the Long-wavelength Observations of the Tenuous ISM), is a balloon-borne astronomy experiment dedicated to study the polarization of dust emission from the diffuse ISM in our Galaxy [1]. The observations of PILOT have two major scientific objectives. Firstly, they will allow us to constrain the large-scale geometry of the magnetic field in our Galaxy and to study in details the alignment properties of dust grains with respect to the magnetic field. In this domain, the measurements of PILOT will complement those of the Planck satellite at longer wavelengths. In particular, they will bring information at a better angular resolution, which is critical in crowded regions such as the Galactic plane. They will allow us to better understand how the magnetic field is shaping the ISM material on large scale in molecular clouds, and the role it plays in the gravitational collapse leading to star formation. Secondly, the PILOT observations will allow us to measure for the first time the polarized dust emission towards the most diffuse regions of the sky, where the measurements are the most easily interpreted in terms of the physics of dust. In this particular domain, PILOT will play a role for future CMB missions similar to that played by the Archeops experiment for Planck. The results of PILOT will allow us to gain knowledge about the magnetic properties of dust grains and about the structure of the magnetic field in the diffuse ISM that is necessary to a precise foreground subtraction in future polarized CMB measurements. The PILOT measurements, combined with those of Planck at longer wavelengths, will therefore allow us to further constrain the dust models. The outcome of such studies will likely impact the instrumental and technical choices for the future space missions dedicated to CMB polarization. The PILOT instrument will allow observations in two photometric channels at wavelengths 240 μm and 550 μm, with an angular resolution of a few arcminutes. We will make use of large format bolometer arrays, developed for the PACS instrument on board the Herschel satellite. With 1024 detectors per photometric channel and photometric band optimized for the measurement of dust emission, PILOT is likely to become the most sensitive experiment for this type of measurements. The PILOT experiment will take advantage of the large gain in sensitivity allowed by the use of large format, filled bolometer arrays at frequencies more favorable to the detection of dust emission. This paper presents the optical design, optical characterization and its performance. We begin with a presentation of the instrument and the optical system and then we summarise the main optical tests performed. In section III, we present preliminary end-to-end test results.

Development and Testing of the Nurse Manager EBP Competency Scale.

PubMed

Shuman, Clayton J; Ploutz-Snyder, Robert J; Titler, Marita G

2018-02-01

The purpose of this study was to develop and evaluate the validity and reliability of an instrument to measure nurse manager competencies regarding evidence-based practice (EBP). The Nurse Manager EBP Competency Scale consists of 16 items for respondents to indicate their perceived level of competency on a 0 to 3 Likert-type scale. Content validity was demonstrated through expert panel review and pilot testing. Principal axis factoring and Cronbach's alpha evaluated construct validity and internal consistency reliability, respectively. Eighty-three nurse managers completed the scale. Exploratory factor analysis resulted in a 16-item scale with two subscales, EBP Knowledge ( n = 6 items, α = .90) and EBP Activity ( n = 10 items, α = .94). Cronbach's alpha for the entire scale was .95. The Nurse Manager EBP Competency Scale is a brief measure of nurse manager EBP competency with evidence of validity and reliability. The scale can enhance our understanding in future studies regarding how nurse manager EBP competency affects implementation.

Development and testing of the Multidimensional Trust in Health Care Systems Scale.

PubMed

Egede, Leonard E; Ellis, Charles

2008-06-01

To describe the development and psychometric testing of the Multidimensional Trust in Health Care Systems Scale (MTHCSS). Scale development occurred in 2 phases. In phase 1, a pilot instrument with 70 items was generated from the review of the trust literature, focus groups, and expert opinion. The 70 items were pilot tested in a sample of 256 students. Exploratory factor analysis was used to derive an orthogonal set of correlated factors. In phase 2, the final scale was administered to 301 primary care patients to assess reliability and validity. Phase 2 participants also completed validated measures of patient-centered care, health locus of control, medication nonadherence, social support, and patient satisfaction. In phase 1, a 17-item scale (MTHCSS) was developed with 10 items measuring trust in health care providers, 4 items measuring trust in health care payers, and 3 items measuring trust in health care institutions. In phase 2, the 17-item MTHCSS had a mean score of 63.0 (SD 8.8); the provider subscale had a mean of 40.0 (SD 6.2); the payers subscale had a mean of 12.8 (SD 3.0); and the institutions subscale had a mean of 10.3 (SD 2.1). Cronbach's alpha for the MTHCSS was 0.89 and 0.92, 0.74, and 0.64 for the 3 subscales. The MTHCSS was significantly correlated with patient-centered care (r = .22 to .62), locus of control-chance (r = .42), medication nonadherence (r = -.22), social support (r = .25), and patient satisfaction (r = .67). The MTHCSS is a valid and reliable instrument for measuring the 3 objects of trust in health care and is correlated with patient-level health outcomes.

Preliminary investigation of the STBBI Stigma Scale: Description and pilot results.

PubMed

Wagner, Anne C; MacLean, Rachel

2017-11-09

Sexually transmitted and blood-borne infections (STBBIs) are associated with stigmatizing attitudes and beliefs, which can affect the quality of and access to health care, as well as mental health and quality of life. The current study describes the adaptation from an HIV-related stigma scale and pilot testing of a new STBBI Stigma Scale, assessing the stigmatizing attitudes and beliefs of health and social service providers in Canada. 144 health and social service providers from across Canada completed the newly adapted scale assessing stigma associated with HIV, hepatitis C, other viral STBBIs and bacterial STBBIs, as well as demographic information, a scale of social desirability and measures of convergent and divergent validity. Participants were recruited through listservs and completed the scale online. The new scale, consisting of 21 items for each category, demonstrated excellent internal consistency, reliability, and convergent and divergent validity. The factor structure of the scale supports a tripartite model of stigma consisting of stereotyping, prejudice and discrimination. Stereotyping had the highest relative scores on the subscales, and attitudes regarding other viral STBBIs differed significantly from the other STBBI categories. The new scale provides a contextually relevant and applicable psychometrically valid tool to assess STBBI-related stigma among health and social service providers in Canada. The tool can be used to assess attitudes and beliefs, as well as guide self-assessment and possible trainings for providers.

Demonstration-scale evaluation of a novel high-solids anaerobic digestion process for converting organic wastes to fuel gas and compost.

PubMed

Rivard, C J; Duff, B W; Dickow, J H; Wiles, C C; Nagle, N J; Gaddy, J L; Clausen, E C

1998-01-01

Early evaluations of the bioconversion potential for combined wastes such as tuna sludge and sorted municipal solid waste (MSW) were conducted at laboratory scale and compared conventional low-solids, stirred-tank anaerobic systems with the novel, high-solids anaerobic digester (HSAD) design. Enhanced feedstock conversion rates and yields were determined for the HSAD system. In addition, the HSAD system demonstrated superior resiliency to process failure. Utilizing relatively dry feedstocks, the HSAD system is approximately one-tenth the size of conventional low-solids systems. In addition, the HSAD system is capable of organic loading rates (OLRs) on the order of 20-25 g volatile solids per liter digester volume per d (gVS/L/d), roughly 4-5 times those of conventional systems. Current efforts involve developing a demonstration-scale (pilot-scale) HSAD system. A two-ton/d plant has been constructed in Stanton, CA and is currently in the commissioning/startup phase. The purposes of the project are to verify laboratory- and intermediate-scale process performance; test the performance of large-scale prototype mechanical systems; demonstrate the long-term reliability of the process; and generate the process and economic data required for the design, financing, and construction of full-scale commercial systems. This study presents conformational fermentation data obtained at intermediate-scale and a snapshot of the pilot-scale project.

Sono-photo-degradation of carbamazepine in a thin falling film reactor: Operation costs in pilot plant.

PubMed

Expósito, A J; Patterson, D A; Monteagudo, J M; Durán, A

2017-01-01

The photo-Fenton degradation of carbamazepine (CBZ) assisted with ultrasound radiation (US/UV/H 2 O 2 /Fe) was tested in a lab thin film reactor allowing high TOC removals (89% in 35min). The synergism between the UV process and the sonolytic one was quantified as 55.2%. To test the applicability of this reactor for industrial purposes, the sono-photo-degradation of CBZ was also tested in a thin film pilot plant reactor and compared with a 28L UV-C conventional pilot plant and with a solar Collector Parabolic Compound (CPC). At a pilot plant scale, a US/UV/H 2 O 2 /Fe process reaching 60% of mineralization would cost 2.1 and 3.8€/m 3 for the conventional and thin film plant respectively. The use of ultrasound (US) produces an extra generation of hydroxyl radicals, thus increasing the mineralization rate. In the solar process, electric consumption accounts for a maximum of 33% of total costs. Thus, for a TOC removal of 80%, the cost of this treatment is about 1.36€/m 3 . However, the efficiency of the solar installation decreases in cloudy days and cannot be used during night, so that a limited flow rate can be treated. Copyright © 2016 Elsevier B.V. All rights reserved.

Concordance of common data elements for assessment of subjective cognitive complaints after mild-traumatic brain injury: a TRACK-TBI Pilot Study.

PubMed

Ngwenya, Laura B; Gardner, Raquel C; Yue, John K; Burke, John F; Ferguson, Adam R; Huang, Michael C; Winkler, Ethan A; Pirracchio, Romain; Satris, Gabriela G; Yuh, Esther L; Mukherjee, Pratik; Valadka, Alex B; Okonkwo, David O; Manley, Geoffrey T

2018-06-04

To determine characteristics and concordance of subjective cognitive complaints (SCCs) 6 months following mild-traumatic brain injury (mTBI) as assessed by two different TBI common data elements (CDEs). The Transforming Research and Clinical Knowledge in Traumatic Brain Injury (TRACK-TBI) Pilot Study was a prospective observational study that utilized the NIH TBI CDEs, Version 1.0. We examined variables associated with SCC, performance on objective cognitive tests (Wechsler Adult Intelligence Scale, California Verbal Learning Test, and Trail Making Tests A and B), and agreement on self-report of SCCs as assessed by the acute concussion evaluation (ACE) versus the Rivermead Post Concussion Symptoms Questionnaire (RPQ). In total, 68% of 227 participants endorsed SCCs at 6 months. Factors associated with SCC included less education, psychiatric history, and being assaulted. Compared to participants without SCC, those with SCC defined by RPQ performed significantly worse on all cognitive tests. There was moderate agreement between the two measures of SCCs (kappa = 0.567 to 0.680). We show that the symptom questionnaires ACE and RPQ show good, but not excellent, agreement for SCCs in an mTBI study population. Our results support the retention of RPQ as a basic CDE for mTBI research. BSI-18: Brief Symptom Inventory; 18CDEs: common data elements; CT: computed tomography; CVLT: California Verbal Learning Test; ED: emergency department; GCS: Glasgow coma scale; LOC: loss of consciousnessm; TBI: mild-traumatic brain injury; PTA: post-traumatic amnesia; SCC: subjective cognitive complaints; TBI: traumatic brain injury; TRACK-TBI: Transforming Research and Clinical Knowledge in Traumatic Brain Injury; TMT: Trail Making Test; WAIS-PSI: Wechsler Adult Intelligence Scale, Fourth Edition, Processing Speed Index.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Raymond H.; Stone, James; Truax, Ryan

Batch tests, column tests, and predictive reactive transport modeling can be done before ISR begins as part of the decision making/permitting process by bracketing possible post-restoration conditions; Help address stakeholder concerns; The best predictions require actual restored groundwater in contact with the downgradient solid phase; Resulting modeling provides a range of natural attenuation rates and assists with designing the best locations and time frames for continued monitoring; Field pilot tests are the best field-scale data and can provide the best model input and calibration data

Calibration of Airframe and Occupant Models for Two Full-Scale Rotorcraft Crash Tests

NASA Technical Reports Server (NTRS)

Annett, Martin S.; Horta, Lucas G.; Polanco, Michael A.

2012-01-01

Two full-scale crash tests of an MD-500 helicopter were conducted in 2009 and 2010 at NASA Langley's Landing and Impact Research Facility in support of NASA s Subsonic Rotary Wing Crashworthiness Project. The first crash test was conducted to evaluate the performance of an externally mounted composite deployable energy absorber under combined impact conditions. In the second crash test, the energy absorber was removed to establish baseline loads that are regarded as severe but survivable. Accelerations and kinematic data collected from the crash tests were compared to a system integrated finite element model of the test article. Results from 19 accelerometers placed throughout the airframe were compared to finite element model responses. The model developed for the purposes of predicting acceleration responses from the first crash test was inadequate when evaluating more severe conditions seen in the second crash test. A newly developed model calibration approach that includes uncertainty estimation, parameter sensitivity, impact shape orthogonality, and numerical optimization was used to calibrate model results for the second full-scale crash test. This combination of heuristic and quantitative methods was used to identify modeling deficiencies, evaluate parameter importance, and propose required model changes. It is shown that the multi-dimensional calibration techniques presented here are particularly effective in identifying model adequacy. Acceleration results for the calibrated model were compared to test results and the original model results. There was a noticeable improvement in the pilot and co-pilot region, a slight improvement in the occupant model response, and an over-stiffening effect in the passenger region. This approach should be adopted early on, in combination with the building-block approaches that are customarily used, for model development and test planning guidance. Complete crash simulations with validated finite element models can be used to satisfy crash certification requirements, thereby reducing overall development costs.

Performance evaluation of Space Shuttle SRB parachutes from air drop and scaled model wind tunnel tests. [Solid Rocket Booster recovery system

NASA Technical Reports Server (NTRS)

Moog, R. D.; Bacchus, D. L.; Utreja, L. R.

1979-01-01

The aerodynamic performance characteristics have been determined for the Space Shuttle Solid Rocket Booster drogue, main, and pilot parachutes. The performance evaluation on the 20-degree conical ribbon parachutes is based primarily on air drop tests of full scale prototype parachutes. In addition, parametric wind tunnel tests were performed and used in parachute configuration development and preliminary performance assessments. The wind tunnel test data are compared to the drop test results and both sets of data are used to determine the predicted performance of the Solid Rocket Booster flight parachutes. Data from other drop tests of large ribbon parachutes are also compared with the Solid Rocket Booster parachute performance characteristics. Parameters assessed include full open terminal drag coefficients, reefed drag area, opening characteristics, clustering effects, and forebody interference.

Can a brief two-hour interdisciplinary communication skills training be successful in undergraduate medical education?

PubMed

Bachmann, Cadja; Barzel, Anne; Roschlaub, Silke; Ehrhardt, Maren; Scherer, Martin

2013-11-01

To pilot-test feasibility, acceptance and learning-outcomes of a brief interdisciplinary communication skills training program in undergraduate medical education. A two-hour interdisciplinary communication skills program with simulated patients was developed and pilot-tested with clinical students at Hamburg University. Five psychosocial specialties facilitated the training. Composite effects were measured qualitatively and quantitatively. Eighty students volunteered to participate in the pilot-program (intervention-group). Their evaluations of the program were very positive (1.1 on a six-point scale). Benefits were seen in feedback, increase of self-confidence, cross-disciplinary clinical and communication experience. Students who did not volunteer (n=206) served as the control-group. The intervention-group performed significantly better (p=0.023) in a primary care communication examination and female students performed better than males. Clinical teachers evaluated the pilot-training very positively with regard to learning-outcomes and feasibility. The positive results from the pilot-training led to implementation into the regular curriculum. A two-hour interdisciplinary communication skills training program is beneficial for medical students with regard to communication competencies, self-confidence and learning-outcomes. The training is feasible within given time-frames and limited staff resources. The high teaching load for small-group-training are split between five specialties. The concept might be an interesting option for other faculties. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Psychometric properties of the Transitions from Foster Care Key Leader Survey.

PubMed

Salazar, Amy M; Brown, Eric C; Monahan, Kathryn C; Catalano, Richard F

2016-04-01

This study summarizes the development and piloting of the Transitions from Foster Care Key Leader Survey (TFC-KLS), an instrument designed to measure change in systems serving young people transitioning from foster care to adulthood. The Jim Casey Youth Opportunity Initiative's logic model was used as a basis for instrument development. The instrument was piloted with 119 key leaders in six communities. Seven of eight latent scales performed well in psychometric testing. The relationships among the 24 measures of system change were explored. A CFA testing overall model fit was satisfactory following slight modifications. Finally, a test of inter-rater reliability between two raters did not find reliable reporting of service availability in a supplemental portion of the survey. The findings were generally positive and supported the validity and utility of the instrument for measuring system change, following some adaptations. Implications for the field are discussed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Assessment of a Point-of-Use Ultrafiltration System for Turbidity and Microbial Pathogen Removal

EPA Science Inventory

U.S. EPA’s Office of Research and Development has been evaluating the performance of point-of-use (POU) devices designed for use in homes and small businesses for many years. In collaboration with the University of Cincinnati, a series of pilot-scale tests were conducted on a Mat...

Comparative Study on the Implication of Three Nanoparticles on the Removal of Trichloroethylene by Adsorption - The Pilot and Rapid Small-Scale Column Tests

EPA Science Inventory

The impact of three commercially-available nanoparticles (NPs) on trichloroethylene (TCE) adsorption onto granular activated carbon (GAC) was investigated. TCE Adsorption isotherm and column breakthrough experiments were conducted in the presence and absence of silicon dioxide (S...

PERFORMANCE ASSESSMENT OF IN-WELL AERATION FOR THE REMEDIATION OF AN AQUIFER CONTAMINATED BY MULTICOMPONENT IMMISCIBLE LIQUID

EPA Science Inventory

A pilot-scale test to evaluate the performance of a vertical recirculation well equipped with an in-well air stripper was conducted at Hill AFB, Utah, in an aquifer contaminated with petroleum and chlorinated solvents. During the two months of operation, the air stripping system ...

ADVANCED OXIDATION PROCESS TECHNOLOGY (ULTRAVIOLET RADIATION/OZONE TREATMENT) FOR REMOVAL OF METHYL TERTIARY BUTYL ETHER (MTBE) IN GROUND WATER SUPPLIES.

EPA Science Inventory

U.S. EPA’s Office of Research and Development in Cincinnati, Ohio has been testing and evaluating MTBE removal in dechlorinated tap water using three oxidant combinations: hydrogen peroxide/ozone, ultraviolet irradiation (UV)/ozone, and UV/ozone/hydrogen peroxide. Pilot-scale st...

An Ice Protection and Detection Systems Manufacturer's Perspective

NASA Technical Reports Server (NTRS)

Sweet, Dave

2009-01-01

Accomplishments include: World Class Aircraft Icing Research Center and Facility. Primary Sponsor/Partner - Aircraft Icing Consortia/Meetings. Icing Research Tunnel. Icing Test Aircraft. Icing Codes - LEWICE/Scaling, et al. Development of New Technologies (SBIR, STTR, et al). Example: Look Ahead Ice Detection. Pilot Training Materials. Full Cooperation with Academia, Government and Industry.

Development of Measures of Organizational Leadership for Health Promotion

ERIC Educational Resources Information Center

Barrett, Linda; Plotnikoff, Ronald C.; Raine, Kim; Anderson, Donna

2005-01-01

This study describes the development and psychometric evaluation of four scales measuring leadership for health promotion at an organizational level in the baseline survey (n = 144) of the Alberta Heart Health Project. Content validity was established through a series of focus groups and expert opinion appraisals, pilot testing of a draft based on…

Possible application of the Environmental Relative Moldiness Index in France: A pilot study in Brittany

EPA Science Inventory

Our goal was to determine if the US Environmental Relative Moldiness Index (ERMI) scale might have application in France. Twenty homes in Brittany, north western region of France were classified by inspection as “Moldy” or “Non-Moldy”. Dust and air samples were collected (MiTest ...

PILOT-SCALE INCINERATION OF PCB-CONTAMINATED SEDIMENTS FROM THE NEW BEDFORD HARBOR HOT SPOT SUPERFUND SITE

EPA Science Inventory

Testing was performed at the EPA's Incineration Research Facility (IRF) to determine the incinerability of contaminated marine sediment from the Hot Spot in the New Bedford Harbor Superfund Site. he contaminants at this site were PCBs, at concentrations up to >200,000 mg/kg, and ...

Ceramic Filter for Small System Drinking Water Treatment: Evaluation of Membrane Pore Size and Importance of Integrity Monitoring

EPA Science Inventory

Ceramic filtration has recently been identified as a promising technology for drinking water treatment in households and small communities. This paper summarizes the results of a pilot-scale study conducted at the U.S. Environmental Protection Agency’s (EPA’s) Test & Evaluation ...

Adhesive performance of washed cottonseed meal at high solid contents and low temperatures

USDA-ARS?s Scientific Manuscript database

Water-washed cottonseed meal (WCSM) has been shown as a promising biobased wood adhesive. Recently, we prepared WSCM in a pilot scale for promoting its industrial application. In this work, we tested the adhesive strength and viscosity of the adhesive preparation with high solid contents (up to 30%...

Assessment of a Point-of-Use Ultrafiltration System for Turbidity and Microbial Pathogen Removal

EPA Science Inventory

U.S. EPA’s Office of Research and Development has been evaluating the performance of point-of-use (POU) devices designed for use in homes and small businesses for many years. In collaboration with the University of Cincinnati, a series of pilot-scale tests were conducted on a Ma...

Stages of Psychometric Measure Development: The Example of the Generalized Expertise Measure (GEM)

ERIC Educational Resources Information Center

Germain, Marie-Line

2006-01-01

This paper chronicles the steps, methods, and presents hypothetical results of quantitative and qualitative studies being conducted to develop a Generalized Expertise Measure (GEM). Per Hinkin (1995), the stages of scale development are domain and item generation, content expert validation, and pilot test. Content/face validity and internal…

Pilot scale production of the vaccine adjuvant Proteoliposome derived Cochleates (AFCo1) from Neisseria meningitidis serogroup B

PubMed Central

2013-01-01

The use of new adjuvants in vaccine formulations is a subject of current research. Only few parenteral adjuvants have been licensed. We have developed a mucosal and parenteral adjuvant known as AFCo1 (Adjuvant Finlay Cochleate 1, derived from proteoliposomes of N. meningitidis B) using a dialysis procedure to produce them on lab scale. The immunogenicity of the AFCo1 produced by dialysis has been already evaluated, but it was necessary to demonstrate the feasibility of a larger-scale manufacturing process. Therefore, we used a crossflow diafiltration system (CFS) that allows easy scale up to obtain large batches in an aseptic environment. The aim of this work was to produce AFCo1 on pilot scale, while conserving the adjuvant properties. The proteoliposomes (raw material) were resuspended in a buffer containing sodium deoxycholate and were transformed into AFCo1 under the action of a calcium forming buffer. The detergent was removed from the protein solution by diafiltration to a constant volume. In this CFS, we used a hollow fiber cartridge from Amicon (polysulfona cartridge of 10 kDa porosity, 1mm channel diameter of fiber and 0.45 m2 area of filtration), allowing production of a batch of up to 20 L. AFCo1 were successfully produced by tangential filtration to pilot scale. The batch passed preliminary stability tests. Nasal immunization of BALB/c mice, induced specific saliva IgA and serum IgG. The induction of Th1 responses were demonstrated by the induction of IgG2a, IFNγ and not IL-5. The adjuvant action over Neisseria (self) antigens and with co-administered (heterologous) antigens such as ovalbumin and a synthetic peptide from haemolytic Streptococcus B was also demonstrated. PMID:23458578

Centralized automated quality assurance for large scale health care systems. A pilot method for some aspects of dental radiography.

PubMed

Benn, D K; Minden, N J; Pettigrew, J C; Shim, M

1994-08-01

President Clinton's Health Security Act proposes the formation of large scale health plans with improved quality assurance. Dental radiography consumes 4% ($1.2 billion in 1990) of total dental expenditure yet regular systematic office quality assurance is not performed. A pilot automated method is described for assessing density of exposed film and fogging of unexposed processed film. A workstation and camera were used to input intraoral radiographs. Test images were produced from a phantom jaw with increasing exposure times. Two radiologists subjectively classified the images as too light, acceptable, or too dark. A computer program automatically classified global grey level histograms from the test images as too light, acceptable, or too dark. The program correctly classified 95% of 88 clinical films. Optical density of unexposed film in the range 0.15 to 0.52 measured by computer was reliable to better than 0.01. Further work is needed to see if comprehensive centralized automated radiographic quality assurance systems with feedback to dentists are feasible, are able to improve quality, and are significantly cheaper than conventional clerical methods.

Pilot-scale testing membrane bioreactor for wastewater reclamation in industrial laundry.

PubMed

Andersen, M; Kristensen, G H; Brynjolf, M; Grüttner, H

2002-01-01

A pilot-scale study of membrane bioreactor treatment for reclamation of wastewater from Berendsen Textile Service industrial laundry in Søborg, Denmark was carried out over a 4 month period. A satisfactory COD degradation was performed resulting in a low COD in the permeate (< 50 mg/l). To obtain satisfactory treatment, addition of nitrogen was necessary. The biodegradability of the permeate was very low (BOD5 < 2 mg/l). A hydraulic retention time of 1 d turned out to be sufficient at a sludge concentration of 10 g MLSS/l. Through addition of a cationic polymer, a satisfactory dewaterability of the sludge was reached. Membrane tests showed that operating at a trans-membrane pressure of 3 bar and a cross-flow velocity of 4 m/s, a flux of 120 l/m2h can be expected without using chemicals for membrane cleaning. The quality of the permeate was very good when comparing to the reuse quality demands of water to the wash processes. Reuse of the permeate in all rinsing steps requires additional treatment through reverse osmosis.

Development and pilot testing of an intervention to promote care engagement and adherence among HIV-positive Kenyan MSM.

PubMed

Graham, Susan M; Micheni, Murugi; Kombo, Bernadette; Van Der Elst, Elisabeth M; Mugo, Peter M; Kivaya, Esther; Aunon, Frances; Kutner, Bryan; Sanders, Eduard J; Simoni, Jane M

2015-12-01

In many African settings, MSM are a stigmatized group whose access to and engagement in HIV care may be challenging. Our aim was to design a targeted, culturally appropriate intervention to promote care engagement and antiretroviral therapy (ART) adherence for MSM in coastal Kenya, and describe intervention safety, feasibility, and acceptability based upon a small pilot study. Based on qualitative work including in-depth interviews with HIV-positive MSM and focus groups with providers, we developed a tailored intervention and conducted a pilot test to refine intervention materials and procedures. The Shikamana intervention combines modified Next-Step Counseling by trained providers, support from a trained peer navigator, and tailored use of SMS messaging, phone calls, and discrete pill carriers. Providers, including counselors and clinicians, work together with peer navigators as a case management team. Forty HIV-positive MSM aged 19-51 participated in intervention development and testing. Six counselors, three clinical officers, and four MSM peers were trained in intervention procedures. Of 10 ART-naïve participants who enrolled in the pilot, eight completed follow-up with no adverse events reported. One participant was lost to follow-up after 2 months and another failed to initiate ART despite ongoing counseling. No adverse events were reported. Staff feedback and exit interviews rated the intervention as feasible and acceptable. This adherence support intervention tailored for Kenyan MSM was well tolerated, feasible, and acceptable in the pilot phase. A randomized controlled trial of a scaled-up programme to estimate intervention efficacy is ongoing.

Reclamation of grey water for non-potable purposes using pilot-scale solar photocatalytic tubular reactors.

PubMed

Saran, Sarangapany; Arunkumar, Patchaiyappan; Manjari, Gangarapu; Devipriya, Suja P

2018-05-05

Application of pilot-scale slurry-type tubular photocatalytic reactor was tested for the decentralized treatment of actual grey water. The reactors were fabricated by reusing the locally available materials at low cost, operated in batch recycle mode with 25 L of grey water. The influence of operational parameters such as catalysts' concentration, initial slurry pH and addition of H 2 O 2 on COD abatement were optimized. The results show that Ag-decorated TiO 2 showed a two-fold increase in COD abatement than did pure TiO 2 . Better COD abatement was observed under acidic conditions, and addition of H 2 O 2 significantly increases the rate of COD abatement. Within 2 h, 99% COD abatement was observed when the reactor was operated with optimum operational conditions. Silver ion lixiviate was also monitored during the experiment and is five times less than the permissible limits. The catalyst shows good stability even after five cycles without much loss in its photocatalytic activity. The results clearly reveal that pilot-scale slurry tubular solar photocatalytic reactors could be used as a cost-effective method to treat grey water and the resulting clean water could be reused for various non-potable purposes, thus conserving precious water resource. This study favours decentralized grey water treatment and possible scaling up of solar photocatalytic reactor using locally available materials for the potential reuse of treated water.

Solar photocatalitycal treatment of carbofuran at lab and pilot scale: effect of classical parameters, evaluation of the toxicity and analysis of organic by-products.

PubMed

Lopez-Alvarez, Blady; Torres-Palma, Ricardo A; Peñuela, Gustavo

2011-07-15

In this work the TiO(2) solar-photocatalytical degradation of the pesticide carbofuran (CBF) in water, at lab and pilot scale, was studied. At lab scale the evaluation of CBF concentration (14-282 μmol L(-1)) showed that the system followed a Langmuir-Hinshelwood kinetics type. TiO(2) concentration (0.05-2 g L(-1)) and initial pH (3-9) were also evaluated and optimized using the surface response methodology and the Pareto diagram. In the range of variables studied, initial pH 7.60 and 1.43 g L(-1) of TiO(2) favoured the efficiency of the process. Under optimal conditions the evolution of substrate, chemical oxygen demand, dissolved organic carbon, toxicity and organics by-products were evaluated. In the pilot scale tests, using direct sunlight, 55 mg L(-1) of CBF in a commercial formulation was eliminated after 420 min; while after 900 min of treatment 80% of toxicity (1/E(50) on Vibrium Fischeri), 80% of chemical oxygen demand and 60% of dissolved organic carbon were removed. The analysis and evolution of five CBF by-products, as well the evaluation of the treatment in the presence of isopropanol or using acetonitrile as a solvent suggest that the degradation is mainly carried out by OH radical attack. Finally, a schema depicting the main degradation pathway is proposed. Copyright © 2011 Elsevier B.V. All rights reserved.

A pilot study for determining the optimal operation condition for simultaneously controlling the emissions of PCDD/Fs and PAHs from the iron ore sintering process.

PubMed

Chen, Yu-Cheng; Tsai, Perng-Jy; Mou, Jin-Luh; Kuo, Yu-Chieh; Wang, Shih-Min; Young, Li-Hao; Wang, Ya-Fen

2012-09-01

In this study, the cost-benefit analysis technique was developed and incorporated into the Taguchi experimental design to determine the optimal operation combination for the purpose of providing a technique solution for controlling both emissions of PCDD/Fs and PAHs, and increasing both the sinter productivity (SP) and sinter strength (SS) simultaneously. Four operating parameters, including the water content, suction pressure, bed height, and type of hearth layer, were selected and all experimental campaigns were conducted on a pilot-scale sinter pot to simulate various sintering operating conditions of a real-scale sinter plant. The resultant optimal combination could reduce the total carcinogenic emissions arising from both emissions of PCDD/Fs and PAHs by 49.8%, and increase the sinter benefit associated with the increase in both SP and SS by 10.1%, as in comparison with the operation condition currently used in the real plant. The ANOVA results indicate that the suction pressure was the most dominant parameter in determining the optimal operation combination. The above result was theoretically plausible since the higher suction pressure provided more oxygen contents leading to the decrease in both PCDD/F and PAH emissions. But it should be noted that the results obtained from the present study were based on pilot scale experiments, conducting confirmation tests in a real scale plant are still necessary in the future. Copyright © 2012 Elsevier Ltd. All rights reserved.

Wind Tunnel Tests Conducted to Develop an Icing Flight Simulator

NASA Technical Reports Server (NTRS)

Ratvasky, Thomas P.

2001-01-01

As part of NASA's Aviation Safety Program goals to reduce aviation accidents due to icing, NASA Glenn Research Center is leading a flight simulator development activity to improve pilot training for the adverse flying characteristics due to icing. Developing flight simulators that incorporate the aerodynamic effects of icing will provide a critical element in pilot training programs by giving pilots a pre-exposure of icing-related hazards, such as ice-contaminated roll upset or tailplane stall. Integrating these effects into training flight simulators will provide an accurate representation of scenarios to develop pilot skills in unusual attitudes and loss-of-control events that may result from airframe icing. In order to achieve a high level of fidelity in the flight simulation, a series of wind tunnel tests have been conducted on a 6.5-percent-scale Twin Otter aircraft model. These wind tunnel tests were conducted at the Wichita State University 7- by 10-ft wind tunnel and Bihrle Applied Research's Large Amplitude Multiple Purpose Facility in Neuburg, Germany. The Twin Otter model was tested without ice (baseline), and with two ice configurations: 1) Ice on the horizontal tail only; 2) Ice on the wing, horizontal tail, and vertical tail. These wind tunnel tests resulted in data bases of aerodynamic forces and moments as functions of angle of attack; sideslip; control surface deflections; forced oscillations in the pitch, roll, and yaw axes; and various rotational speeds. A limited amount of wing and tail surface pressure data were also measured for comparison with data taken at Wichita State and with flight data. The data bases from these tests will be the foundation for a PC-based Icing Flight Simulator to be delivered to Glenn in fiscal year 2001.

Modeling of UH-60A Hub Accelerations with Neural Networks

NASA Technical Reports Server (NTRS)

Kottapalli, Sesi

2002-01-01

Neural network relationships between the full-scale, flight test hub accelerations and the corresponding three N/rev pilot floor vibration components (vertical, lateral, and longitudinal) are studied. The present quantitative effort on the UH-60A Black Hawk hub accelerations considers the lateral and longitudinal vibrations. An earlier study had considered the vertical vibration. The NASA/Army UH-60A Airloads Program flight test database is used. A physics based "maneuver-effect-factor (MEF)", derived using the roll-angle and the pitch-rate, is used. Fundamentally, the lateral vibration data show high vibration levels (up to 0.3 g's) at low airspeeds (for example, during landing flares) and at high airspeeds (for example, during turns). The results show that the advance ratio and the gross weight together can predict the vertical and the longitudinal vibration. However, the advance ratio and the gross weight together cannot predict the lateral vibration. The hub accelerations and the advance ratio can be used to satisfactorily predict the vertical, lateral, and longitudinal vibration. The present study shows that neural network based representations of all three UH-60A pilot floor vibration components (vertical, lateral, and longitudinal) can be obtained using the hub accelerations along with the gross weight and the advance ratio. The hub accelerations are clearly a factor in determining the pilot vibration. The present conclusions potentially allow for the identification of neural network relationships between the experimental hub accelerations obtained from wind tunnel testing and the experimental pilot vibration data obtained from flight testing. A successful establishment of the above neural network based link between the wind tunnel hub accelerations and the flight test vibration data can increase the value of wind tunnel testing.

Effect of Atomoxetine on the Cognitive Functions in Treatment of Attention Deficit Hyperactivity Disorder in Children with Congenital Hypothyroidism: A Pilot Study.

PubMed

Yang, Rongwang; Gao, Weijia; Li, Rong; Zhao, Zhengyan

2015-04-19

With early initiation of thyroxine supplementation, children with congenital hypothyroidism (CH) retain some subtle deficits, such as attention and inhibitory control problems. This study assessed the effects of atomoxetine on cognitive functions in treatment of attention deficit hyperactivity disorder (ADHD) symptoms in children with CH. In a 6-month, open-labeled pilot study, 12 children were recruited and received atomoxetine. The measures of efficacy were scores on the Swanson, Nolan and Pelham Teacher and Parent Rating Scale, version IV (SNAP-IV) and Clinical Global Impression-Severity scale (CGI-S). The cognitive functions were evaluated with the Wechsler Intelligence Scale for Chinese Children, Digit Span, Wisconsin Card Sorting Test, and Stroop test. A statistically significant difference was found between the mean CGI-S and SNAP-IV scores before and after treatment (p < 0.01). All the indicators of cognitive functions at the endpoint were improved compared with those at baseline. No serious adverse events were reported. Atomoxetine appears to be useful in improving ADHD symptoms, as well as cognitive functions, in children with CH. Larger, randomized, double-blinded, clinical trials are required to replicate these results. © The Author 2015. Published by Oxford University Press on behalf of CINP.

Increasing Access to Mental Health Care With Breathe, an Internet-Based Program for Anxious Adolescents: Study Protocol for a Pilot Randomized Controlled Trial

PubMed Central

Wozney, Lori; Bagnell, Alexa; Fitzpatrick, Eleanor; Curtis, Sarah; Jabbour, Mona; Johnson, David; Rosychuk, Rhonda J; Young, Michael; Ohinmaa, Arto; Joyce, Anthony; McGrath, Patrick

2016-01-01

Background There is a demand to make first-line treatments, including cognitive behavioural therapy (CBT) for adolescent anxiety disorders, more widely available. Internet-based CBT is proposed to circumvent access and availability barriers and reduce health care system costs. Recent reviews suggest more evidence is needed to establish the treatment effects of Internet-based CBT in children and adolescents and to determine related economic impacts. Objective This pilot trial aims to collect the necessary data to inform the planning of a full-scale RCT to test the effectiveness of the Internet-based CBT program Breathe (Being Real, Easing Anxiety: Tools Helping Electronically). Methods We are conducting a 27-month, 2-arm parallel-group, pilot randomized controlled trial (RCT). Outcomes will inform the planning of a full-scale RCT aimed to test the effectiveness of Internet-based CBT with a population of adolescents with moderate to mild anxiety problems. In the pilot RCT we will: (1) define a minimal clinically important difference (MCID) for the primary outcome measure (total anxiety score using the Multidimensional Anxiety Scale for Children); (2) determine a sample size for the full-scale RCT; (3) estimate recruitment and retention rates; (4) measure intervention acceptability to inform critical intervention changes; (5) determine the use of co-interventions; and (6) conduct a cost-consequence analysis to inform a cost-effectiveness analysis in the full-scale RCT. Adolescents aged 13-17 years seeking care for an anxiety complaint from a participating emergency department, mobile or school-based crisis team, or primary care clinic are being screened for interest and eligibility. Enrolled adolescents are being randomly allocated to either 8 weeks of Internet-based CBT with limited telephone and e-mail support, or a control group with access to a static webpage listing anxiety resources. Adolescents are randomly assigned using a computer generated allocation sequence. Data are being collected at baseline, treatment completion, and at a 3-month follow-up. Results Currently, adolescents are being enrolled in the study. Enrolment is taking place between March 2014 and February 2016; data collection will conclude May 2016. We expect that analysis and results will be available by August 2016. Conclusions In many communities, the resources available for front-line anxiety treatment are outweighed by the need for care. This pilot RCT is an essential step to designing a robust RCT to evaluate the effectiveness of an Internet-based CBT program for adolescents with moderate to mild anxiety problems. Trial Registration Clinicaltrials.gov NCT02059226; http://clinicaltrials.gov/ct2/show/NCT02059226 (Archived by WebCite at http://www.webcitation.org/6epF8v7k4) PMID:26825111

A Pilot Study of Computer-Based Simulation Training for Enhancing Family Medicine Residents' Competence in Computerized Settings.

PubMed

Shachak, Aviv; Domb, Sharon; Borycki, Elizabeth; Fong, Nancy; Skyrme, Alison; Kushniruk, Andre; Reis, Shmuel; Ziv, Amitai

2015-01-01

We previously developed a prototype computer-based simulation to teach residents how to integrate better EMR use in the patient-physician interaction. To evaluate the prototype, we conducted usability tests with three non-clinician students, followed by a pilot study with 16 family medicine residents. The pilot study included pre- and post-test surveys of competencies and attitudes related to using the EMR in the consultation and the acceptability of the simulation, as well as 'think aloud' observations. After using the simulation prototypes, the mean scores for competencies and attitudes improved from 14.88/20 to 15.63/20 and from 22.25/30 to 23.13/30, respectively; however, only the difference for competencies was significant (paired t-test; t=-2.535, p=0.023). Mean scores for perceived usefulness and ease of use of the simulation were good (3.81 and 4.10 on a 5-point scale, respectively). Issues identified in usability testing include confusing interaction with some features, preferences for a more interactive representation of the EMR, and more options for shared decision making. In conclusion, computer-based simulation may be an effective and acceptable tool for teaching residents how to better use EMRs in clinical encounters.

Novel Inorganic/Polymer Composite Membranes for CO 2 Capture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ho, W.S. Winston; Dutta, Prabir K.; Schmit, Steve J.

The objective of this project is to develop a cost-effective design and manufacturing process for new membrane modules that capture CO 2 from flue gas in coal-fired power plants. The membrane consisted of a thin selective layer including inorganic (zeolite) embedded in a polymer structure so that it can be made in a continuous manufacturing process. The membrane was incorporated in spiral-wound modules for the field test with actual flue gas at the National Carbon Capture Center (NCCC) in Wilsonville, AL and bench scale tests with simulated flue gas at the Ohio State University (OSU). Using the modules for post-combustionmore » CO 2 capture is expected to achieve the DOE target of $40/tonne CO 2 captured (in 2007 dollar) for 2025. Membranes with the amine-containing polymer cover layer on zeolite-Y (ZY) nanoparticles deposited on the polyethersulfone (PES) substrate were successfully synthesized. The membranes showed a high CO 2 permeance of about 1100 GPU (gas permeation unit, 1 GPU = 10 -6 cm 3 (STP)/(cm 2 • s • cm Hg), 3000 GPU = 10-6 mol/(m 2 • s • Pa)) with a high CO 2/N 2 selectivity of > 200 at the typical flue gas conditions at 57°C (about 17% water vapor in feed gas) and > 1400 GPU CO 2 permeance with > 500 CO 2/N 2 selectivity at 102°C (~ 80% water vapor). The synthesis of ZY nanoparticles was successfully scaled up, and the pilot-scale membranes were also successfully fabricated using the continuous membrane machine at OSU. The transport performance of the pilot-scale membranes agreed reasonably well with the lab-scale membranes. The results from both the lab-scale and scale-up membranes were used for the techno-economic analysis. The scale-up membranes were fabricated into prototype spiral-wound membrane modules for continuous testing with simulated or real flue gas. For real flue gas testing, we worked with NCCC, in consultation with TriSep Corporation, Gradient Technology and American Electric Power (AEP). The membrane module demonstrated > 800 GPU of CO 2 permeance and > 150 CO 2/N 2 selectivity when tested with real flue gas at NCCC. The results obtained were used to update the techno-economic analysis. In addition, the EH&S assessment of the membranes for post-combustion CO 2 capture was conducted.« less

Using minced horseradish roots and peroxides for the deodorization of swine manure: a pilot scale study.

PubMed

Govere, Ephraim M; Tonegawa, Masami; Bruns, Mary Ann; Wheeler, Eileen F; Kephart, Kenneth B; Voigt, Jean W; Dec, Jerzy

2007-04-01

Enzymes that have proven to be capable of removing toxic compounds from water and soil may also be useful in the deodorization of animal manures. Considering that pork production in the US is a $40-billion industry with over half a million workers, odor control to protect air quality in the neighboring communities must be considered an essential part of managing livestock facilities. This pilot scale (20-120 L) study tested the use of minced horseradish (Armoracia rusticana L.) roots (1:10 roots to swine slurry ratio), with calcium peroxide (CaO(2) at 34 mM) or hydrogen peroxide (H(2)O(2) at 68 mM), to deodorize swine slurry taken from a 40,000-gallon storage pit at the Pennsylvania State University's Swine Center. Horseradish is known to contain large amounts of peroxidase, an enzyme that, in the presence of peroxides, can polymerize phenolic odorants and thus reduce the malodor. Twelve compounds commonly associated with malodor (seven volatile fatty acids or VFAs, three phenolic compounds and two indolic compounds) were used as odor indicators. Their concentration in swine slurry before and after treatment was determined by gas chromatography (GC) to assess the deodorization effect. The pilot scale testing demonstrated a complete removal of phenolic odorants (with a detection limit of 0.5 mg L(-1)) from the swine slurry, which was consistent with our previous laboratory experiments using 30-mL swine slurry samples. Horseradish could be recycled (reused) five times while retaining significant reduction in the concentration of phenolic odorants. In view of these findings, inexpensive plant materials, such as horseradish, represent a promising tool for eliminating phenolic odorants from swine slurry.

Coaching as Part of a Pilot Quality Rating Scale Initiative: Challenges to--and Supports for--the Change-Making Process

ERIC Educational Resources Information Center

Ackerman, Debra J.

2008-01-01

Several nonprofit agencies in a large Midwestern city provide assistance to early care and education programs participating in a pilot Quality Rating Scale (QRS) initiative by pairing them with itinerant consultants, who are known as coaches. Despite this assistance, not all programs improve their QRS score. Furthermore, while pilot stakeholders…

The pilot plant for electron beam food processing

NASA Astrophysics Data System (ADS)

Migdal, W.; Walis, L.; Chmielewski, A. G.

1993-07-01

In the frames of the national programme on the application of irradiation for food preservation and hygienization an experimental plant for electron beam processing has been established in INCT. The pilot plant has been constructed inside an old fort what decreases significantly the cost of the investment. The pilot plant is equipped with a small research accelerator Pilot (10 MeV, 1 kW) and an industrial unit Elektronika (10 MeV, 10 kW). This allows both laboratory and full technological scale testing of the elaborated process to be conducted. The industrial unit is being equipped with e-/X conversion target, for high density products irradiation. On the basis of the research there were performed at different scientific institutions in Poland, health authorities have issued permissions for permanent treatment of spices, garlic, onions and temporary permissions for mushrooms, and potatoes. Dosimetric methods have been elaborated for the routine use at the plant. In the INCT laboratory methods for the control of e-/X treated food have been established.

REMOVAL OF METHYL T-BUTYL ETHER (MTBE) FROM WATER BY PERVAPORATION: BENCH-SCALE AND PILOT SCALE EVALUATIONS

EPA Science Inventory

The ability of pervaporation to remove methyl t-butyl ether (MTBE) from water was evaluated at bench- and pilot-scales. Process parameters studied included flow rate, temperature, MTBE concentration, membrane module type, and permeate pressure. Pervaporation performance was ass...

Testing the robustness of Citizen Science projects: Evaluating the results of pilot project COMBER.

PubMed

Chatzigeorgiou, Giorgos; Faulwetter, Sarah; Dailianis, Thanos; Smith, Vincent Stuart; Koulouri, Panagiota; Dounas, Costas; Arvanitidis, Christos

2016-01-01

Citizen Science (CS) as a term implies a great deal of approaches and scopes involving many different fields of science. The number of the relevant projects globally has been increased significantly in the recent years. Large scale ecological questions can be answered only through extended observation networks and CS projects can support this effort. Although the need of such projects is apparent, an important part of scientific community cast doubt on the reliability of CS data sets. The pilot CS project COMBER has been created in order to provide evidence to answer the aforementioned question in the coastal marine biodiversity monitoring. The results of the current analysis show that a carefully designed CS project with clear hypotheses, wide participation and data sets validation, can be a valuable tool for the large scale and long term changes in marine biodiversity pattern change and therefore for relevant management and conservation issues.

Design and analysis of a pilot scale biofiltration system for odorous air

DOE Office of Scientific and Technical Information (OSTI.GOV)

Classen, J.J.; Young, J.S.; Bottcher, R.W.

2000-02-01

Three pilot-scale biofilters and necessary peripheral equipment were built to clean odorous air from the pit of a swine gestation building at North Carolina State University. A computer measured temperatures, flow rates, and pressure drops. It also controlled and measured the moisture content of a biofilter medium comprised of a 3:1 mixture of yard waste compost to wood chips mixture (by volume). The system was evaluated to ensure that the biofilters would be useful for performing scientific experiments concerning the reduction of swine odor on future research projects. The capability of the biofilters to remove odor was measured using amore » cotton swatch absorption method and an odor panel. The average odor reductions measured by odor intensity, irritation intensity, and unpleasantness for five tests were 61%, 58%, and 84%, respectively. No significant differences in odor reduction performance were found between the biofilters.« less

Performance of ultrafiltration membrane process combined with coagulation/sedimentation.

PubMed

Jang, N Y; Watanabe, Y; Minegishi, S

2005-01-01

Effects of coagulation/sedimentation as a pre-treatment on the dead-end ultrafiltration (UF) membrane process were studied in terms of membrane fouling and removal efficiency of natural dissolved organic matter, using Chitose River water. Two types of experiment were carried out. One was a bench scale membrane filtration with jar-test and the other was membrane filtration pilot plant combined with the Jet Mixed Separator (JMS) as a pre-coagulation/sedimentation unit. In the bench scale experiment, the effects of coagulant dosage, pH and membrane operating pressure on the membrane fouling and removal efficiency of natural dissolved organic matter were investigated. In the pilot plant experiment, we also investigated the effect of pre-coagulation/sedimentation on the membrane fouling and the removal efficiency of natural dissolved organic matter. Coagulation/sedimentation prior to membrane filtration process controlled the membrane fouling and increased the removal efficiency of natural dissolved organic matter.

Wind-tunnel investigation of longitudinal and lateral-directional stability and control characteristics of a 0.237-scale model of a remotely piloted research vehicle with a thick, high-aspect-ratio supercritical wing

NASA Technical Reports Server (NTRS)

Byrdsong, T. A.; Brooks, C. W., Jr.

1980-01-01

A 0.237-scale model of a remotely piloted research vehicle equipped with a thick, high-aspect-ratio supercritical wing was tested in the Langley 8-foot transonic tunnel to provide experimental data for a prediction of the static stability and control characteristics of the research vehicle as well as to provide an estimate of vehicle flight characteristics for a computer simulation program used in the planning and execution of specific flight-research mission. Data were obtained at a Reynolds number of 16.5 x 10 to the 6th power per meter for Mach numbers up to 0.92. The results indicate regions of longitudinal instability; however, an adequate margin of longitudinal stability exists at a selected cruise condition. Satisfactory effectiveness of pitch, roll, and yaw control was also demonstrated.

Current Development in Treatment and Hydrogen Energy Conversion of Organic Solid Waste

NASA Astrophysics Data System (ADS)

Shin, Hang-Sik

2008-02-01

This manuscript summarized current developments on continuous hydrogen production technologies researched in Korea advanced institute of science and technology (KAIST). Long-term continuous pilot-scale operation of hydrogen producing processes fed with non-sterile food waste exhibited successful results. Experimental findings obtained by the optimization processes of growth environments for hydrogen producing bacteria, the development of high-rate hydrogen producing strategies, and the feasibility tests for real field application could contribute to the progress of fermentative hydrogen production technologies. Three major technologies such as controlling dilution rate depending on the progress of acidogenesis, maintaining solid retention time independently from hydraulic retention time, and decreasing hydrogen partial pressure by carbon dioxide sparging could enhance hydrogen production using anaerobic leaching beds reactors and anaerobic sequencing batch reactors. These findings could contribute to stable, reliable and effective performances of pilot-scale reactors treating organic wastes.

Cost Effective Bioethanol via Acid Pretreatment of Corn Stover, Saccharification, and Conversion via a Novel Fermentation Organism: Cooperative Research and Development Final Report, CRADA Number: CRD-12-485

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dowe, N.

2014-05-01

This research program will convert acid pretreated corn stover to sugars at the National Renewable Energy Laboratory (NREL) and then transfer these sugars to Honda R&D and its partner the Green Earth Institute (GEI) for conversion to ethanol via a novel fermentation organism. In phase one, NREL will adapt its pretreatment and saccharification process to the unique attributes of this organism, and Honda R&D/GEI will increase the sugar conversion rate as well as the yield and titer of the resulting ethanol. In later phases, NREL, Honda R&D, and GEI will work together at NREL to optimize and scale-up to pilot-scalemore » the Honda R&D/GEI bioethanol production process. The final stage will be to undertake a pilot-scale test at NREL of the optimized bioethanol conversion process.« less

Air purification from a mixture VOCs in the pilot-scale trickle-bed bioreactor (TBB)

NASA Astrophysics Data System (ADS)

Sarzyński, Rafał; Gąszczak, Agnieszka; Janecki, Daniel; Bartelmus, Grażyna

2017-10-01

The efficiency of the air bio-purification from the mixture of two volatile organic compounds (styrene and p-xylene) was studied. The process was carried out in a pilot-scale trickle-bed bioreactor installation designed to purify ˜200 m3h-1 of the polluted air. The bioreactor operated at concurrent flow of gas and liquid (mineral salt solution) through packing (polypropylene Ralu rings) covered with a thin layer of microorganisms (bacterial consortium of Pseudomonas sp. E-022150 and Pseudomonas putida mt-2). The experiments, carried out for various values of a reactor load with pollutant, confirmed the great efficiency of the investigated process. At the tested bed load with pollution (inlet specific pollutant load was changed within the range of 41 - 84 gm-3 h -1), styrene conversion degree changed within the range of 80-87% and p-xylene conversion degree within the range of 42-48%.

Using PlayDoh Astronomy for Understanding the Size and Scale of the Earth-Moon System and as a Probe for Spatial Translation Ability

NASA Astrophysics Data System (ADS)

Grundstrom, Erika

2013-01-01

To help students love science more and to help them understand the vast distances that pervade astronomy, we use kinesthetic modeling of the Earth-Moon system using PlayDoh. When coupled with discussion, we found (in a pilot study) that students of all ages (children up through adults) acquired a more accurate mental representation of the Earth-Moon system. During early September 2012, we devised and implemented a curriculum unit that focused on the Earth-Moon system and how that relates to eclipses for six middle-Tennessee 6th grade public school classrooms. For this unit, we used PlayDoh as the kinesthetic modeling tool. First, we evaluated what the students knew about the size and scale prior to this intervention using paper and model pre-tests. Second, we used the PlayDoh to model the Earth-Moon system and when possible, conducted an immediate post-test. The students then engaged with the PlayDoh model to help them understand eclipses. Third, we conducted a one-month-later delayed post-test. One thing to note is that about half of the students had experienced the PlayDoh modeling part of a 5th grade pilot lesson during May 2012 therefore the pre-test acted as a four-month-later delayed post-test for these students. We find, among other things, that students retain relative size information more readily than relative distance information. We also find differences in how consistent students are when trying to translate the size/scale they have in their heads to the different modes of assessment utilized.

Development of a regenerable system employing silica-titania composites for the recovery of mercury from end-box exhaust at a chlor-alkali facility.

PubMed

Stokke, Jennifer M; Mazyck, David W

2008-04-01

The release of mercury to the environment is of particular concern because of its volatility, persistence, and tendency to bioaccumulate. The recovery of mercury from end-box exhaust at chlor-alkali facilities is important to prevent release into the environment and reduce emissions as required by NESHAP (National Emission Standards for Hazardous Air Pollutants). A pilot-scale photocatalytic reactor packed with silica-titania composite (STC) pellets was tested at a chloralkali facility over a 3-month period. This pilot reactor treated up to 10 ft3/min (ACFM) of end-box exhaust and achieved 95% removal. The pilot reactor was able to maintain excellent removal efficiency even with large fluctuations in influent mercury concentration (400-1600 microg/ft3). The STC pellets were regenerated ex situ by regeneration with hydrochloric acid and performed similarly to virgin STC pellets when returned to service. On the basis of these promising results, two full-scale reactors with in situ regeneration capabilities were installed and operated. After optimization, these reactors performed similarly to the pilot reactor. A cost analysis was performed comparing the treatment costs (i.e., cost per pound of mercury removed) for sulfur-impregnated activated carbon and the STC system. The STC proved to be both technologically and economically feasible for this installation.

Pilot-scale testing of renewable biocatalyst for swine manure treatment and mitigation of odorous VOCs, ammonia and hydrogen sulfide emissions

NASA Astrophysics Data System (ADS)

Maurer, Devin L.; Koziel, Jacek A.; Bruning, Kelsey; Parker, David B.

2017-02-01

Comprehensive control of odors, hydrogen sulfide (H2S), ammonia (NH3), and greenhouse gas (GHG) emissions associated with swine production is a critical need. A pilot-scale experiment was conducted to evaluate surface-applied soybean peroxidase (SBP) and calcium peroxide (CaO2) as a manure additive to mitigate emissions of odorous volatile organic compounds (VOC) including dimethyl disulfide/methanethiol (DMDS/MT), dimethyl trisulfide, n-butyric acid, valeric acid, isovaleric acid, p-cresol, indole, and skatole. The secondary impact on emissions of NH3, H2S, and GHG was also measured. The SBP was tested at four treatments (2.28-45.7 kg/m2 manure) with CaO2 (4.2% by weight of SBP) over 137 days. Significant reductions in VOC emissions were observed: DMDS/MT (36.2%-84.7%), p-cresol (53.1%-89.5%), and skatole (63.2%-92.5%). There was a corresponding significant reduction in NH3 (14.6%-67.6%), and significant increases in the greenhouse gases CH4 (32.7%-232%) and CO2 (20.8%-124%). The remaining emissions (including N2O) were not statistically different. At a cost relative to 0.8% of a marketed hog it appears that SBP/CaO2 treatment could be a promising option at the lowest (2.28 kg/m2) treatment rate for reducing odorous gas and NH3 emissions at swine operations, and field-scale testing is warranted.

[Effects of an intensive thalassotherapy and aquatic therapy program in stroke patients. A pilot study].

PubMed

Morer, C; Boestad, C; Zuluaga, P; Alvarez-Badillo, A; Maraver, F

2017-09-16

Stroke remains the leading cause of acquired disability. Health and social planning and management may vary and although prevention is crucial, having better treatments and strategies to reduce disability is needed. To determine the effect of an intensive program of thalassotherapy and aquatic therapy in stroke patients, valuing clinical parameters and functional validated scales. A quasi-experimental prospective study consisting of a specific program assessed pre- and post- 3 weeks treatment to 26 stroke patients with a mild-moderate disability. The outcomes measured were: Berg Balance scale, Timed Up and Go test, 10-meter walking test, 6-minute walking test and pain Visual Analogue Scale. After intervention, participants had a significant improvement in all outcomes measured. Our results suggest that an intensive program of thalassotherapy and aquatic therapy could be useful during stroke rehabilitation to improve balance, gait and pain.

Selection of starter cultures for the production of sour cassava starch in a pilot-scale fermentation process.

PubMed

Penido, Fernanda Corrêa Leal; Piló, Fernanda Barbosa; Sandes, Sávio Henrique de Cicco; Nunes, Álvaro Cantini; Colen, Gecernir; Oliveira, Evelyn de Souza; Rosa, Carlos Augusto; Lacerda, Inayara Cristina Alves

2018-02-28

Sour cassava starch (Polvilho azedo) is obtained from a spontaneous fermentation conducted by microorganisms from raw materials and fermentation tanks. This product is traditionally used in the baking industry for the manufacture of biscuits and Brazilian cheese breads. However, the end of fermentation is evaluated empirically, and the process occurs without standardization, which results in products of inconsistent quality. Predominant microbiota from a cassava flour manufacturer was isolated in order to select starter cultures for the production of sour cassava starch in a pilot-scale fermentation process. Lactic acid bacteria and yeasts were isolated, enumerated and grouped by Restriction Fragment Length Polymorphism, and PCR fingerprinting, respectively. One isolate of each molecular profile was identified by sequencing of the rRNA gene. LAB were prevalent throughout the entire process. Lactobacillus brevis (21.5%), which produced the highest values of acidity, and Lactobacillus plantarum (13.9%) were among the most frequent species. Pichia scutulata (52.2%) was the prevalent yeast and showed amylolytic activity. The aforementioned species were tested as single and mixed starter cultures in a pilot-scale fermentation process for 28 days. L. plantarum exhibited better performance as a starter culture, which suggests its potential for the production of sour cassava starch. Copyright © 2018 Sociedade Brasileira de Microbiologia. Published by Elsevier Editora Ltda. All rights reserved.

The effects of golf training in patients with stroke: a pilot study.

PubMed

Schachten, Tobias; Jansen, Petra

2015-05-01

Stroke is the most common neurological disease and the primary cause of lifelong disability in industrialized countries. Because of this it is important to investigate any kind of successful therapy. From the 24 recruited stroke patients who were between 23 and 72 years old, 14 patients were separated either in a golf training group (EG), or a social communication meeting (CG). Both groups met for one hour sessions, twice a week, for ten weeks. All participants completed assessment tests before and after the experimental period: cognitive tests measuring attention (Go/No-Go task), visual-spatial memory (Block-Tapping test) and mental rotation performance (MRT); a balance test (Berg Balance Scale), and an emotional well-being test (CES-D-Scale). The results show that both groups improved in the CES Scale, the block-tapping test and the balance test. In addition, stroke patients who received a golf training showed a significant improvement in the MRT comparing to the control group (CG). It is indicated that golf training can improve visual imagery ability in stroke patients, even late after stroke.

DEVELOPING A COST EFFECTIVE ENVIRONMENTAL SOLUTION FOR PRODUCED WATER AND CREATING A ''NEW'' WATER RESOURCE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glenn Doran

1997-04-28

This report summarizes the status of this project for the quarter January 1, 1997 to March 31, 1997. Phase II has been started and Task 7, Develop Pilot Scale Test Work Plan has been completed. The operational portion of this phase, Task 8 has been initiated with several pieces of pilot equipment already on-site. The start up of the full process train will not occur until the next quarter. The project is slightly behind schedule. A no cost extension was requested and was granted. The anticipated completion date is December 31, 1997. The project is on budget.

Combined use of field and laboratory testing to predict preferred flow paths in an heterogeneous aquifer.

PubMed

Gierczak, R F D; Devlin, J F; Rudolph, D L

2006-01-05

Elevated nitrate concentrations within a municipal water supply aquifer led to pilot testing of a field-scale, in situ denitrification technology based on carbon substrate injections. In advance of the pilot test, detailed characterization of the site was undertaken. The aquifer consisted of complex, discontinuous and interstratified silt, sand and gravel units, similar to other well studied aquifers of glaciofluvial origin, 15-40 m deep. Laboratory and field tests, including a conservative tracer test, a pumping test, a borehole flowmeter test, grain-size analysis of drill cuttings and core material, and permeameter testing performed on core samples, were performed on the most productive depth range (27-40 m), and the results were compared. The velocity profiles derived from the tracer tests served as the basis for comparison with other methods. The spatial variation in K, based on grain-size analysis, using the Hazen method, were poorly correlated with the breakthrough data. Trends in relative hydraulic conductivity (K/K(avg)) from permeameter testing compared somewhat better. However, the trends in transient drawdown with depth, measured in multilevel sampling points, corresponded particularly well with those of solute mass flux. Estimates of absolute K, based on standard pumping test analysis of the multilevel drawdown data, were inversely correlated with the tracer test data. The inverse nature of the correlation was attributed to assumptions in the transient drawdown packages that were inconsistent with the variable diffusivities encountered at the scale of the measurements. Collectively, the data showed that despite a relatively low variability in K within the aquifer under study (within a factor of 3), water and solute mass fluxes were concentrated in discrete intervals that could be targeted for later bioremediation.

Large Pilot Scale Testing of Linde/BASF Post-Combustion CO 2 Capture Technology at the Abbott Coal-Fired Power Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Brien, Kevin C.

The work summarized in this report is the first step towards a project that will re-train and create jobs for personnel in the coal industry and continue regional economic development to benefit regions impacted by previous downturns. The larger project is aimed at capturing ~300 tons/day (272 metric tonnes/day) CO 2 at a 90% capture rate from existing coal- fired boilers at the Abbott Power Plant on the campus of University of Illinois (UI). It will employ the Linde-BASF novel amine-based advanced CO 2 capture technology, which has already shown the potential to be cost-effective, energy efficient and compact atmore » the 0.5-1.5 MWe pilot scales. The overall objective of the project is to design and install a scaled-up system of nominal 15 MWe size, integrate it with the Abbott Power Plant flue gas, steam and other utility systems, and demonstrate the viability of continuous operation under realistic conditions with high efficiency and capacity. The project will also begin to build a workforce that understands how to operate and maintain the capture plants by including students from regional community colleges and universities in the operation and evaluation of the capture system. This project will also lay the groundwork for follow-on projects that pilot utilization of the captured CO 2 from coal-fired power plants. The net impact will be to demonstrate a replicable means to (1) use a standardized procedure to evaluate power plants for their ability to be retrofitted with a pilot capture unit; (2) design and construct reliable capture systems based on the Linde-BASF technology; (3) operate and maintain these systems; (4) implement training programs with local community colleges and universities to establish a workforce to operate and maintain the systems; and (5) prepare to evaluate at the large pilot scale level various methods to utilize the resulting captured CO 2. Towards the larger project goal, the UI-led team, together with Linde, has completed a preliminary design for the carbon capture pilot plant with basic engineering and cost estimates, established permitting needs, identified approaches to address Environmental, Health, and Safety concerns related to pilot plant installation and operation, developed approaches for long-term use of the captured carbon, and established strategies for workforce development and job creation that will re-train coal operators to operate carbon capture plants. This report describes Phase I accomplishments and demonstrates that the project team is well-prepared for full implementation of Phase 2, to design, build, and operate the carbon capture pilot plant.« less

Demonstrating Functional Equivalence of Pilot and Production Scale Freeze-Drying of BCG

PubMed Central

ten Have, R.; Reubsaet, K.; van Herpen, P.; Kersten, G.; Amorij, J.-P.

2016-01-01

Process analytical technology (PAT)-tools were used to monitor freeze-drying of Bacille Calmette-Guérin (BCG) at pilot and production scale. Among the evaluated PAT-tools, there is the novel use of the vacuum valve open/close frequency for determining the endpoint of primary drying at production scale. The duration of primary drying, the BCG survival rate, and the residual moisture content (RMC) were evaluated using two different freeze-drying protocols and were found to be independent of the freeze-dryer scale evidencing functional equivalence. The absence of an effect of the freeze-dryer scale on the process underlines the feasibility of the pilot scale freeze-dryer for further BCG freeze-drying process optimization which may be carried out using a medium without BCG. PMID:26981867

Demonstrating Functional Equivalence of Pilot and Production Scale Freeze-Drying of BCG.

PubMed

Ten Have, R; Reubsaet, K; van Herpen, P; Kersten, G; Amorij, J-P

2016-01-01

Process analytical technology (PAT)-tools were used to monitor freeze-drying of Bacille Calmette-Guérin (BCG) at pilot and production scale. Among the evaluated PAT-tools, there is the novel use of the vacuum valve open/close frequency for determining the endpoint of primary drying at production scale. The duration of primary drying, the BCG survival rate, and the residual moisture content (RMC) were evaluated using two different freeze-drying protocols and were found to be independent of the freeze-dryer scale evidencing functional equivalence. The absence of an effect of the freeze-dryer scale on the process underlines the feasibility of the pilot scale freeze-dryer for further BCG freeze-drying process optimization which may be carried out using a medium without BCG.

Eliciting preferences for priority setting in genetic testing: a pilot study comparing best-worst scaling and discrete-choice experiments.

PubMed

Severin, Franziska; Schmidtke, Jörg; Mühlbacher, Axel; Rogowski, Wolf H

2013-11-01

Given the increasing number of genetic tests available, decisions have to be made on how to allocate limited health-care resources to them. Different criteria have been proposed to guide priority setting. However, their relative importance is unclear. Discrete-choice experiments (DCEs) and best-worst scaling experiments (BWSs) are methods used to identify and weight various criteria that influence orders of priority. This study tests whether these preference eliciting techniques can be used for prioritising genetic tests and compares the empirical findings resulting from these two approaches. Pilot DCE and BWS questionnaires were developed for the same criteria: prevalence, severity, clinical utility, alternatives to genetic testing available, infrastructure for testing and care established, and urgency of care. Interview-style experiments were carried out among different genetics professionals (mainly clinical geneticists, researchers and biologists). A total of 31 respondents completed the DCE and 26 completed the BWS experiment. Weights for the levels of the six attributes were estimated by conditional logit models. Although the results derived from the DCE and BWS experiments differed in detail, we found similar valuation patterns in the DCE and BWS experiments. The respondents attached greatest value to tests with high clinical utility (defined by the availability of treatments that reduce mortality and morbidity) and to testing for highly prevalent conditions. The findings from this study exemplify how decision makers can use quantitative preference eliciting methods to measure aggregated preferences in order to prioritise alternative clinical interventions. Further research is necessary to confirm the survey results.

Assessment of a Point-of-Use Ultrafiltration System for Turbidity and Microbial Pathogen Removal - Paper

EPA Science Inventory

U.S. EPA’s Office of Research and Development has been evaluating the performance of point-of-use (POU) devices designed for use in homes and small businesses for many years. In collaboration with the University of Cincinnati, a series of pilot-scale tests were conducted on a Ma...

THE FATE OF TRACE METALS IN A ROTARY KILN INCINERATOR WITH A VENTURI/PACKED COLUMN SCRUBBER - VOLUME II: APPENDICES

EPA Science Inventory

A 5-week series of pilot-scale incineration tests, employing a synthetic waste feed, was performed at the U.S. Environmental Protection Agency's Incineration Research Facility to evaluate the fate of trace metals fed to a rotary kiln incinerator equipped with a venturi scrubber/p...

FATE OF TRACE METALS IN A ROTARY KILN INCINERATOR WITH A SINGLE-STAGE IONIZING WET SCRUBBER. VOLUME 1. TECHNICAL RESULTS.

EPA Science Inventory

A series of pilot-scale incineration tests was performed at EPA's Incineration Research Facility (IRF) in Jefferson, Arkansas, to evaluate the fate of trace metals fed to a rotary kiln incinerator equipped with an ionizing wet scrubber (IWS) for particulate and acid gas control. ...

The WISC-III and Raven Coloured Progressive Matrices Test: A Pilot Study of Relationships.

ERIC Educational Resources Information Center

Kluever, Raymond C.; And Others

The relationship between scores on Raven's Coloured Progressive Matrices (CPM) scores and subtest scores and IQs from the Wechsler Intelligence Scale for Children-III (WISC-III) was studied for 28 children aged 6 to 11 years. Subjects had been referred to a university assessment center because they were believed to have exceptional learning…

Development of USPS Laboratory and pilot-scale testing protocols

Treesearch

Carl Houtman; Nancy Ross Sutherland; David Bormett; Donald Donermeyer

2000-01-01

The ultimate goal of the US Postal Service (USPS) Environmentally Benign Stamp Program is to develop stamp adhesives that can be removed by unit operations found in recycling mills. The maintenance of final product quality specifications for a recycling mill while loading the feedstock with a significant quantity of adhesive is the criterion for success of this program...

Oily Sludge Biodetoxification

DTIC Science & Technology

2011-05-01

Sustainability Development to Integration NAVSTA Naval Station NT not tested O&M operation and maintenance OSHA Occupational Safety and Health ...Safety and Health Administration The results presented here and data from previous pilot scale and prototype (Hawaii) demonstrations of oily sludge...designed to treat. While additional degradation may have occurred if the system was supplemented with micronutrients and operated in series, it is

PILOT-SCALE INCINERATION OF PCB-CONTAMINATED SEDIMENTS FROM THE HOT SPOT OF THE NEW BEDFORD HARBOR SUPERFUND SITE

EPA Science Inventory

Testing was performed at the EPA's Incineration Research Facility (IRF) to determine the incinerability of contaminated marine sediment from the Hot Spot in the New Bedford Harbor Superfund Site. he contaminants at this site were PCBs, at concentration up to >200,000 mg/kb, and m...

ENVIRONMENTAL IMPACTS OF THE USE OF ORIMULSION (R): REPORT TO CONGRESS ON PHASE I OF THE ORIMULSION TECHNOLOGY ASSESSMENT PROGRAM, VOLUME 2

EPA Science Inventory

The report gives results of an evaluation of Orimulsion, a bitumen-in-water emulsion produced in Venezuela, to provide a better understanding of the potential environmental impacts associated with its use as a fuel. Pilot-scale tests were conducted at EPA's Environmental Research...

ENVIRONMENTAL IMPACTS OF THE USE OF ORIMULSION.: REPORT TO CONGRESS ON PHASE 1 OF THE ORIMULSION TECHNOLOGY ASSESSMENT PROGRAM

EPA Science Inventory

Orimulsion, a bitumen-in-water emulsion produced in Venezuela, was
evaluated to provide a better understanding of the potential environmental
impacts associated with its use as a fuel. A series of pilot-scale tests were
conducted at the U.S. Environmental Protection Agen...

ENVIRONMENTAL IMPACTS OF THE USE OF ORIMULSION: REPORT TO CONGRESS ON PHASE 1 OF THE ORIMULSION TECHNOLOGY ASSESSMERNT PROGRAM: VOLUME 1:

EPA Science Inventory

The report gives results of an evaluation of Orimulsion, a bitumen-in-water emulsion produced in Venezuela, to provide a better understanding of the potential environmental impacts associated with its use as a fuel. Pilot-scale tests were conducted at EPA's Environmental Research...

THE FATE OF TRACE METALS IN A ROTARY KILN INCINERATOR WITH A SINGLE-STAGE IONIZING WET SCRUBBER - VOLUME II: APPENDICES

EPA Science Inventory

A series of pilot-scale incineration tests was performed at EPA's Incineration Research Facility (IRF) in Jefferson, Arkansas, to evaluate the fate of trace metals fed to a rotary kiln incinerator equipped with an ionizing wet scrubber (IWS) for particulate and acid gas control. ...

77 FR 18793 - Spectrum Sharing Innovation Test-Bed Pilot Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-28

.... 120322212-2212-01] Spectrum Sharing Innovation Test-Bed Pilot Program AGENCY: National Telecommunications... Innovation Test-Bed pilot program to assess whether devices employing Dynamic Spectrum Access techniques can... Spectrum Sharing Innovation Test-Bed (Test-Bed) pilot program to examine the feasibility of increased...

On the relation between personality and job performance of airline pilots.

PubMed

Hormann, H J; Maschke, P

1996-01-01

The validity of a personality questionnaire for the prediction of job success of airline pilots is compared to validities of a simulator checkflight and of flying experience data. During selection, 274 pilots applying for employment with a European charter airline were examined with a multidimensional personality questionnaire (Temperature Structure Scales; TSS). Additionally, the applicants were graded in a simulator checkflight. On the basis of training records, the pilots were classified as performing at standard or below standard after about 3 years of employment in the hiring company. In a multiple-regression model, this dichotomous criterion for job success can be predicted with 73.8% accuracy through the simulator checkflight and flying experience prior to employment. By adding the personality questionnaire to the regression equation, the number of correct classifications increases to 79.3%. On average, successful pilots score substantially higher on interpersonal scales and lower on emotional scales of the TSS.

Genomic Encyclopedia of Type Strains, Phase I: The one thousand microbial genomes (KMG-I) project

DOE PAGES

Kyrpides, Nikos C.; Woyke, Tanja; Eisen, Jonathan A.; ...

2014-06-15

The Genomic Encyclopedia of Bacteria and Archaea (GEBA) project was launched by the JGI in 2007 as a pilot project with the objective of sequencing 250 bacterial and archaeal genomes. The two major goals of that project were (a) to test the hypothesis that there are many benefits to the use the phylogenetic diversity of organisms in the tree of life as a primary criterion for generating their genome sequence and (b) to develop the necessary framework, technology and organization for large-scale sequencing of microbial isolate genomes. While the GEBA pilot project has not yet been entirely completed, both ofmore » the original goals have already been successfully accomplished, leading the way for the next phase of the project. Here we propose taking the GEBA project to the next level, by generating high quality draft genomes for 1,000 bacterial and archaeal strains. This represents a combined 16-fold increase in both scale and speed as compared to the GEBA pilot project (250 isolate genomes in 4+ years). We will follow a similar approach for organism selection and sequencing prioritization as was done for the GEBA pilot project (i.e. phylogenetic novelty, availability and growth of cultures of type strains and DNA extraction capability), focusing on type strains as this ensures reproducibility of our results and provides the strongest linkage between genome sequences and other knowledge about each strain. In turn, this project will constitute a pilot phase of a larger effort that will target the genome sequences of all available type strains of the Bacteria and Archaea.« less

Genomic Encyclopedia of Type Strains, Phase I: The one thousand microbial genomes (KMG-I) project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kyrpides, Nikos C.; Woyke, Tanja; Eisen, Jonathan A.

The Genomic Encyclopedia of Bacteria and Archaea (GEBA) project was launched by the JGI in 2007 as a pilot project with the objective of sequencing 250 bacterial and archaeal genomes. The two major goals of that project were (a) to test the hypothesis that there are many benefits to the use the phylogenetic diversity of organisms in the tree of life as a primary criterion for generating their genome sequence and (b) to develop the necessary framework, technology and organization for large-scale sequencing of microbial isolate genomes. While the GEBA pilot project has not yet been entirely completed, both ofmore » the original goals have already been successfully accomplished, leading the way for the next phase of the project. Here we propose taking the GEBA project to the next level, by generating high quality draft genomes for 1,000 bacterial and archaeal strains. This represents a combined 16-fold increase in both scale and speed as compared to the GEBA pilot project (250 isolate genomes in 4+ years). We will follow a similar approach for organism selection and sequencing prioritization as was done for the GEBA pilot project (i.e. phylogenetic novelty, availability and growth of cultures of type strains and DNA extraction capability), focusing on type strains as this ensures reproducibility of our results and provides the strongest linkage between genome sequences and other knowledge about each strain. In turn, this project will constitute a pilot phase of a larger effort that will target the genome sequences of all available type strains of the Bacteria and Archaea.« less

Pilot-Scale Demonstration of In-Situ Chemical Oxidation Involving Chlorinated Volatile Organic Compounds - Design and Deployment Guidelines (Parris Island, SC, U.S. Marine Corp Recruit Depot, Site 45 Pilot Study)

EPA Science Inventory

A pilot-scale in situ chemical oxidation (ISCO) demonstration, involving subsurface injections of sodium permanganate (NaMnO4), was performed at the US Marine Corp Recruit Depot (MCRD), site 45 (Parris Island (PI), SC). The ground water was originally contaminated with perchloroe...

Measurements of liquid phase residence time distributions in a pilot-scale continuous leaching reactor using radiotracer technique.

PubMed

Pant, H J; Sharma, V K; Shenoy, K T; Sreenivas, T

2015-03-01

An alkaline based continuous leaching process is commonly used for extraction of uranium from uranium ore. The reactor in which the leaching process is carried out is called a continuous leaching reactor (CLR) and is expected to behave as a continuously stirred tank reactor (CSTR) for the liquid phase. A pilot-scale CLR used in a Technology Demonstration Pilot Plant (TDPP) was designed, installed and operated; and thus needed to be tested for its hydrodynamic behavior. A radiotracer investigation was carried out in the CLR for measurement of residence time distribution (RTD) of liquid phase with specific objectives to characterize the flow behavior of the reactor and validate its design. Bromine-82 as ammonium bromide was used as a radiotracer and about 40-60MBq activity was used in each run. The measured RTD curves were treated and mean residence times were determined and simulated using a tanks-in-series model. The result of simulation indicated no flow abnormality and the reactor behaved as an ideal CSTR for the range of the operating conditions used in the investigation. Copyright © 2014 Elsevier Ltd. All rights reserved.

Support of Helicopter 'Free Flight' Operations in the 1996 Olympics

NASA Technical Reports Server (NTRS)

Branstetter, James R.; Cooper, Eric G.

1996-01-01

The microcosm of activity surrounding the 1996 Olympic Games provided researchers an opportunity for demonstrating state-of-the art technology in the first large-scale deployment of a prototype digital communication/navigation/surveillance system in a confined environment. At the same time it provided an ideal opportunity for transportation officials to showcase the merits of an integrated transportation system in meeting the operational needs to transport time sensitive goods and provide public safety services under real-world conditions. Five aeronautical CNS functions using a digital datalink system were chosen for operational flight testing onboard 91 aircraft, most of them helicopters, participating in the Atlanta Short-Haul Transportation System. These included: GPS-based Automatic Dependent Surveillance, Cockpit Display of Traffic Information, Controller-Pilot Communications, Graphical Weather Information (uplink), and Automated Electronic Pilot Reporting (downlink). Atlanta provided the first opportunity to demonstrate, in an actual operating environment, key datalink functions which would enhance flight safety and situational awareness for the pilot and supplement conventional air traffic control. The knowledge gained from such a large-scale deployment will help system designers in development of a national infrastructure where aircraft would have the ability to navigate autonomously.

Evaluating students' perception of their clinical placements - testing the clinical learning environment and supervision and nurse teacher scale (CLES + T scale) in Germany.

PubMed

Bergjan, Manuela; Hertel, Frank

2013-11-01

Clinical nursing education in Germany has not received attention in nursing science and practice for a long time, as it often seems to be a more or less "formalized appendix" of nursing education. Several development projects of clinical education taking place are mainly focused on the qualification of clinical preceptors. However, the clinical context and its influence on learning processes have still not been sufficiently investigated. The aim of this study was the testing of a German version of the clinical learning environment and supervision and nurse teacher scale (CLES + T scale). The sample of the pilot study consists of first-, second- and third-year student nurses (n=240) of a university nursing school from January to March 2011. Psychometric testing of the instrument is carried out by selected methods of classical testing theories using SPPS 19. The results show transferability of all subcategories of the CLES + T scale in the non-academic nursing education system of a university hospital in Germany, without the teacher scale. The strongest factor is "supervisory relationship". The German version of the CLES + T scale may help to evaluate and compare traditional and new models in clinical nursing education. Copyright © 2012 Elsevier Ltd. All rights reserved.

Experimental Studies of the Effects of Anode Composition and Process Parameters on Anode Slime Adhesion and Cathode Copper Purity by Performing Copper Electrorefining in a Pilot-Scale Cell

NASA Astrophysics Data System (ADS)

Zeng, Weizhi; Wang, Shijie; Free, Michael L.

2016-10-01

Copper electrorefining tests were conducted in a pilot-scale cell under commercial tankhouse environment to study the effects of anode compositions, current density, cathode blank width, and flow rate on anode slime behavior and cathode copper purity. Three different types of anodes (high, mid, and low impurity levels) were used in the tests and were analyzed under SEM/EDS. The harvested copper cathodes were weighed and analyzed for impurities concentrations using DC Arc. The adhered slimes and released slimes were collected, weighed, and analyzed for compositions using ICP. It was shown that the lead-to-arsenic ratio in the anodes affects the sintering and coalescence of slime particles. High current density condition can improve anode slime adhesion and cathode purity by intensifying slime particles' coalescence and dissolving part of the particles. Wide cathode blanks can raise the anodic current densities significantly and result in massive release of large slime particle aggregates, which are not likely to contaminate the cathode copper. Low flow rate can cause anode passivation and increase local temperatures in front of the anode, which leads to very intense sintering and coalescence of slime particles. The results and analyses of the tests present potential solutions for industrial copper electrorefining process.

Biodegradation of endocrine disruptors in urban wastewater using Pleurotus ostreatus bioreactor.

PubMed

Křesinová, Zdena; Linhartová, Lucie; Filipová, Alena; Ezechiáš, Martin; Mašín, Pavel; Cajthaml, Tomáš

2018-07-25

The white rot fungus Pleurotus ostreatus HK 35, which is also an edible industrial mushroom commonly cultivated in farms, was tested in the degradation of typical representatives of endocrine disrupters (EDCs; bisphenol A, estrone, 17β-estradiol, estriol, 17α-ethinylestradiol, triclosan and 4-n-nonylphenol); its degradation efficiency under model laboratory conditions was greater than 90% within 12 days and better than that of another published strain P. ostreatus 3004. A spent mushroom substrate from a local farm was tested for its applicability in various batch and trickle-bed reactors in degrading EDCs in model fortified and real communal wastewater. The reactors were tested under various regimes including a pilot-scale trickle-bed reactor, which was finally tested at a wastewater treatment plant. The result revealed that the spent substrate is an efficient biodegradation agent, where the fungus was usually able to remove about 95% of EDCs together with suppression of the estrogenic activity of the sample. The results showed the fungus was able to operate in the presence of bacterial microflora in wastewater without any substantial negative effects on the degradation abilities. Finally, a pilot-scale trickle-bed reactor was installed in a wastewater treatment plant and successfully operated for 10days, where the bioreactor was able to remove more than 76% of EDCs present in the wastewater. Copyright © 2017 Elsevier B.V. All rights reserved.

Dry thermal resistance of Bacillus anthracis (Sterne) spores and spores of other Bacillus species: implications for biological agent destruction via waste incineration.

PubMed

Wood, J P; Lemieux, P; Betancourt, D; Kariher, P; Gatchalian, N G

2010-07-01

To obtain needed data on the dry thermal resistance of Bacillus anthracis spores and other Bacillus species for waste incinerator applications. Tests were conducted in a pilot-scale incinerator utilizing biological indicators comprised of spores of Geobacillus stearothermophilus, Bacillus atrophaeus and B. anthracis (Sterne) and embedded in building material bundles. Tests were also conducted in a dry heat oven to determine the destruction kinetics for the same species. In the pilot-scale incinerator tests, B. atrophaeus and G. stearothermophilus demonstrated similar thermal sensitivity, but B. anthracis (Sterne) was less thermally resistant than G. stearothermophilus. For the dry heat oven tests conducted at 175°C, the D-values were 0·4, 0·2 and 0·3 min for B. atrophaeus, B. anthracis (Sterne) and G. stearothermophilus, respectively. Bacillus anthracis (Sterne) possesses similar or less dry heat resistance compared to B. atrophaeus and G. stearothermophilus. Previous studies have demonstrated conditions under which bacterial spores may survive in an incinerator environment. The data from this study may assist in the selection of surrogates or indicator micro-organisms to ensure B. anthracis spores embedded in building materials are completely inactivated in an incinerator. © 2009 The Society for Applied Microbiology, Journal of Applied Microbiology. No claim to US Government works.

The development and psychometric testing of a theory-based instrument to evaluate nurses' perception of clinical reasoning competence.

PubMed

Liou, Shwu-Ru; Liu, Hsiu-Chen; Tsai, Hsiu-Min; Tsai, Ying-Huang; Lin, Yu-Ching; Chang, Chia-Hao; Cheng, Ching-Yu

2016-03-01

The purpose of the study was to develop and psychometrically test the Nurses Clinical Reasoning Scale. Clinical reasoning is an essential skill for providing safe and quality patient care. Identifying pre-graduates' and nurses' needs and designing training courses to improve their clinical reasoning competence becomes a critical task. However, there is no instrument focusing on clinical reasoning in the nursing profession. Cross-sectional design was used. This study included the development of the scale, a pilot study that preliminary tested the readability and reliability of the developed scale and a main study that implemented and tested the psychometric properties of the developed scale. The Nurses Clinical Reasoning Scale was developed based on the Clinical Reasoning Model. The scale includes 15 items using a Likert five-point scale. Data were collected from 2013-2014. Two hundred and fifty-one participants comprising clinical nurses and nursing pre-graduates completed and returned the questionnaires in the main study. The instrument was tested for internal consistency and test-retest reliability. Its validity was tested with content, construct and known-groups validity. One factor emerged from the factor analysis. The known-groups validity was confirmed. The Cronbach's alpha for the entire instrument was 0·9. The reliability and validity of the Nurses Clinical Reasoning Scale were supported. The scale is a useful tool and can be easily administered for the self-assessment of clinical reasoning competence of clinical nurses and future baccalaureate nursing graduates. Study limitations and further recommendations are discussed. © 2015 John Wiley & Sons Ltd.

In situ remediation of chlorinated solvent-contaminated groundwater using ZVI/organic carbon amendment in China: field pilot test and full-scale application.

PubMed

Yang, Jie; Meng, Liang; Guo, Lin

2018-02-01

Chlorinated solvents in groundwater pose threats to human health and the environment due to their carcinogenesis and bioaccumulation. These problems are often more severe in developing countries such as China. Thus, methods for chlorinated solvent-contaminated groundwater remediation are urgently needed. This study presents a technique of in situ remediation via the direct-push amendment injection that enhances the reductive dechlorination of chlorinated solvents in groundwater in the low-permeability aquifer. A field-based pilot test and a following real-world, full-scale application were conducted at an active manufacturing facility in Shanghai, China. The chlorinated solvents found at the clay till site included 1,1,1-trichloroethane (1,1,1-TCA), 1,1-dichloroethane (1,1-DCA), 1,1-dichloroethylene (1,1-DCE), vinyl chloride (VC), and chloroethane (CA). A commercially available amendment (EHC ® , Peroxychem, Philadelphia, PA) combining zero-valent iron and organic carbon was used to treat the above pollutants. Pilot test results showed that direct-push EHC injection efficiently facilitated the in situ reductive remediation of groundwater contaminated with chlorinated solvents. The mean removal rates of 1,1,1-TCA, 1,1-DCA, and 1,1-DCE at 270 days post-injection were 99.6, 99.3, and 73.3%, respectively, which were obviously higher than those of VC and CA (42.3 and 37.1%, respectively). Clear decreases in oxidation-reduction potential and dissolved oxygen concentration, and increases in Fe 2+ and total organic carbon concentration, were also observed during the monitoring period. These indicate that EHC promotes the anaerobic degradation of chlorinated hydrocarbons primarily via long-term biological reductive dechlorination, with instant chemical reductive dechlorination acting as a secondary pathway. The optimal effective time of EHC injection was 0-90 days, and its radius of influence was 1.5 m. In full-scale application, the maximum concentrations of 1,1,1-TCA and 1,1-DCA in the contaminate plume fell below the relevant Dutch Intervention Values at 180 days post-injection. Moreover, the dynamics of the target pollutant concentrations mirrored those of the pilot test. Thus, we have demonstrated that the direct-push injection of EHC successfully leads to the remediation of chlorinated solvent-contaminated groundwater in a real-world scenario. The parameters determined by this study (e.g., effectiveness, injection amount, injection depth, injection pressures, and radius of influence) are applicable to other low-permeability contaminated sites where in situ remediation by enhanced reductive dechlorination is required.

Model-Based Extracted Water Desalination System for Carbon Sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dees, Elizabeth M.; Moore, David Roger; Li, Li

Over the last 1.5 years, GE Global Research and Pennsylvania State University defined a model-based, scalable, and multi-stage extracted water desalination system that yields clean water, concentrated brine, and, optionally, salt. The team explored saline brines that ranged across the expected range for extracted water for carbon sequestration reservoirs (40,000 up to 220,000 ppm total dissolved solids, TDS). In addition, the validated the system performance at pilot scale with field-sourced water using GE’s pre-pilot and lab facilities. This project encompassed four principal tasks, in addition to Project Management and Planning: 1) identify a deep saline formation carbon sequestration site andmore » a partner that are suitable for supplying extracted water; 2) conduct a techno-economic assessment and down-selection of pre-treatment and desalination technologies to identify a cost-effective system for extracted water recovery; 3) validate the downselected processes at the lab/pre-pilot scale; and 4) define the scope of the pilot desalination project. Highlights from each task are described below: Deep saline formation characterization The deep saline formations associated with the five DOE NETL 1260 Phase 1 projects were characterized with respect to their mineralogy and formation water composition. Sources of high TDS feed water other than extracted water were explored for high TDS desalination applications, including unconventional oil and gas and seawater reverse osmosis concentrate. Technoeconomic analysis of desalination technologies Techno-economic evaluations of alternate brine concentration technologies, including humidification-dehumidification (HDH), membrane distillation (MD), forward osmosis (FO), turboexpander-freeze, solvent extraction and high pressure reverse osmosis (HPRO), were conducted. These technologies were evaluated against conventional falling film-mechanical vapor recompression (FF-MVR) as a baseline desalination process. Furthermore, a quality function deployment (QFD) method was used to compare alternate high TDS desalination technologies to FF-MVR. High pressure reverse osmosis was found to a be a promising alternative desalination technology. A deep-dive technoeconomic analysis of HPRO was performed, including Capex and Opex estimates, for seawater RO (SWRO). Additionally, two additional cases were explored: 1) a comparison of a SWRO plus HPRO system to the option of doubling the size of a standard seawater RO system to achieve the same total pure water recovery rate; and 2) a flue gas desulfurization wastewater treatment zero-liquid discharge (ZLD) application, where preconcentration with RO (SWRO or SWRO + HPRO) before evaporation and crystallization was compared to FF-MVR and crystallization technologies without RO preconcentration. Pre-pilot process validation Pre-pilot-scale tests were conducted using field production water to validate key process steps for extracted water pretreatment. Approximately 5,000 gallons of field produced water was processed through, microfiltration, ultrafiltration, and steam regenerable sorbent operations. Smaller quantities were processed through microclarification. In addition, analytical methods (purge-and-trap gas chromatography and Hach TOC analytical methods) were validated. Lab-scale HPRO elements were constructed and tested at high pressures, to identify and mitigate technical risks of the technology. Lastly, improvements in RO membrane materials were identified as the necessary next step to achieve further improvement in element performance at high pressure. Scope of Field Pilot A field pilot for extracted water pretreatment was designed.« less

Leaching behaviour of different scrap materials at recovery and recycling companies: full-, pilot- and lab-scale investigation.

PubMed

Blondeel, E; Chys, M; Depuydt, V; Folens, K; Du Laing, G; Verliefde, A; Van Hulle, S W H

2014-12-01

Scrap material recovery and recycling companies are confronted with waste water that has a highly fluctuating flow rate and composition. Common pollutants, such as COD, nutrients and suspended solids, potentially toxic metals, polyaromatic hydrocarbons and poly chlorinated biphenyls can exceed the discharge limits. An analysis of the leaching behaviour of different scrap materials and scrap yard sweepings was performed at full-scale, pilot-scale and lab-scale in order to find possible preventive solutions for this waste water problem. The results of these leaching tests (with concentrations that frequently exceeded the Flemish discharge limits) showed the importance of regular sweeping campaigns at the company, leak proof or covered storage of specific scrap materials and oil/water separation on particular leachates. The particulate versus dissolved fraction was also studied for the pollutants. For example, up to 98% of the polyaromatic hydrocarbons, poly chlorinated biphenyls and some metals were in the particulate form. This confirms the (potential) applicability of sedimentation and filtration techniques for the treatment of the majority of the leachates, and as such the rainwater run-off as a whole. Copyright © 2014 Elsevier Ltd. All rights reserved.

Removal of pharmaceuticals during drinking water treatment.

PubMed

Ternes, Thomas A; Meisenheimer, Martin; McDowell, Derek; Sacher, Frank; Brauch, Heinz-Jürgen; Haist-Gulde, Brigitte; Preuss, Gudrun; Wilme, Uwe; Zulei-Seibert, Ninette

2002-09-01

The elimination of selected pharmaceuticals (bezafibrate, clofibric acid, carbamazepine, diclofenac) during drinking water treatment processes was investigated at lab and pilot scale and in real waterworks. No significant removal of pharmaceuticals was observed in batch experiments with sand under natural aerobic and anoxic conditions, thus indicating low sorption properties and high persistence with nonadapted microorganisms. These results were underscored by the presence of carbamazepine in bank-filtrated water with anaerobic conditions in a waterworks area. Flocculation using iron(III) chloride in lab-scale experiments (Jar test) and investigations in waterworks exhibited no significant elimination of the selected target pharmaceuticals. However, ozonation was in some cases very effective in eliminating these polar compounds. In lab-scale experiments, 0.5 mg/L ozone was shown to reduce the concentrations of diclofenac and carbamazepine by more than 90%, while bezafibrate was eliminated by 50% with a 1.5 mg/L ozone dose. Clofibric acid was stable even at 3 mg/L ozone. Under waterworks conditions, similar removal efficiencies were observed. In addition to ozonation, filtration with granular activated carbon (GAC) was very effective in removing pharmaceuticals. Except for clofibric acid, GAC in pilot-scale experiments and waterworks provided a major elimination of the pharmaceuticals under investigation.

An Integrated Hydrogen Production-CO2 Capture Process from Fossil Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhicheng Wang

The new technology concept integrates two significant complementary hydrogen production and CO{sub 2}-sequestration approaches that have been developed at Oak Ridge National Laboratory (ORNL) and Clark Atlanta University. The process can convert biomass into hydrogen and char. Hydrogen can be efficiently used for stationary power and mobile applications, or it can be synthesized into Ammonia which can be used for CO{sub 2}-sequestration, while char can be used for making time-release fertilizers (NH{sub 4}HCO{sub 3}) by absorption of CO{sub 2} and other acid gases from exhaust flows. Fertilizers are then used for the growth of biomass back to fields. This projectmore » includes bench scale experiments and pilot scale tests. The Combustion and Emission Lab at Clark Atlanta University has conducted the bench scale experiments. The facility used for pilot scale tests was built in Athens, GA. The overall yield from this process is 7 wt% hydrogen and 32 wt% charcoal/activated carbon of feedstock (peanut shell). The value of co-product activated carbon is about $1.1/GJ and this coproduct reduced the selling price of hydrogen. And the selling price of hydrogen is estimated to be $6.95/GJ. The green house experimental results show that the samples added carbon-fertilizers have effectively growth increase of three different types of plants and improvement ability of keeping fertilizer in soil to avoid the fertilizer leaching with water.« less

Modular Hydropower Engineering and Pilot Scale Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chesser, Phillip C.

Emrgy has developed, prototyped and tested a modular hydropower system for renewable energy generation. ORNL worked with Emrgy to demonstrate the use of additive manufacturing in the production of the hydrofoils and spokes for the hydrokinetic system. Specifically, during Phase 1 of this effort, ORNL printed and finished machined patterns for both the hydrofoils and spokes that were subsequently used in a sand casting manufacturing process. Emrgy utilized the sand castings for a pilot installation in Denver, CO, where the parts represented an 80% cost savings from the previous prototype build that was manufactured using subtractive manufacturing. In addition, themore » castings were completed with ORNL’s newly developed AlCeMg alloy that will be tested for performance improvements including higher corrosion resistance in a water application than the 6160 alloy used previously« less

Task Order 7. Use of activated carbon for treatment of explosives-contaminated groundwater at the Milan Army Ammunition Plant (MAAP). Final report, Apr 89-May 90

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dennis, R.M.; Wujcik, W.J.; Lowe, W.L.

1990-05-01

The primary objective of this task was to determine the feasibility of using GAC to treat ground water contaminated by explosives at the Milan Army Ammunition Plant (MAAP) in Milan, Tennessee. Laboratory GAC isotherm studies were conducted and two carbons, Atochem, Inc. GAC 830 and Calgon Filtrasorb 300, were selected for further testing in continuous flow GAC columns. Three pilot scale continuous flow GAC column tests were performed at MAAP using the two carbons selected from the laboratory GAC isotherm studies. The results from the laboratory and pilot studies are presented in this report. They show that concurrent removal ofmore » explosives such as TNT, RDX, HMX, Tetryl, and nitrobenzenes from ground water using continuous flow granular activated carbon is feasible.« less

Assessing Quality of Working Life Among Malaysian Workers.

PubMed

Sulaiman, Nur Suffia; Choo, Wan Yuen; Mat Yassim, Abdul Rahim; Van Laar, Darren; Chinna, Karuthan; Majid, Hazreen Abdul

2015-11-01

The Work-Related Quality of Life Scale-2 (WRQLS-2) has been used to measure quality of working life (QOWL) in the United Kingdom. In this study, the scale was translated and normalized into Malay. The scale was translated using the back-translation method, pretesting, and pilot testing. It was conducted among health care and office workers. It was tested in 3 stages; confirmatory factor analysis at stages 1 and 3 and exploratory factor analysis at stage 2. The Malaysian WRQLS-2 had 5 factors: "General Well-Being," "Job and Career Satisfaction," "Employee Engagement," "Home-Work Interface," and "Stress at Work." The scale showed good convergent and construct validity and also reliability. Perception of good QOWL may differ because of cultural influences and varying work environments. The validated Malaysian WRQLS-2 can be used to determine the QOWL of Malaysian office and health care workers. © 2015 APJPH.

Preliminary validation of the Satisfaction With Decision scale with depressed primary care patients

PubMed Central

Wills, Celia E.; Holmes‐Rovner, Margaret

2003-01-01

Abstract Objective To conduct a preliminary validation of the Satisfaction With Decision (SWD) scale with depressed primary care patients. Design  Cross‐sectional observational pilot study using a postal survey. Setting and participants  Depressed primary care patients (n = 97) who recently had made a new decision about antidepressant medication use completed surveys regarding their treatment decisions. Main variables  Measures included patient‐reported satisfaction with decision, decisional conflict, knowledge about depression and treatment, decision involvement, pain and health status, antidepressant medication efficacy, and satisfaction with health services. Results  The SWD scale had good internal consistency reliability (α = 0.85). Evidence for construct validity was confirmed via a hypothesized pattern of relationships between the SWD scale and other measures. Decision satisfaction was associated with several issues of relevance for designing patient‐centred decision support interventions: (1) knowledge about depression and treatment; (2) involvement in health‐related decisions; and (3) aiding evaluation of trade‐offs among pros and cons of treatment. Conclusions  The results of this pilot study show that the SWD scale appears to be a psychometrically sound and practical measure for research with this population. Additional research is needed on the theoretical nature of decision satisfaction and developing and testing patient‐centred decision support interventions for depression treatment. PMID:12752743

Field-scale simulation of chemical flooding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saad, N.

1989-01-01

A three-dimensional compositional chemical flooding simulator (UTCHEM) has been improved. The new mathematical formulation, boundary conditions, and a description of the physicochemical models of the simulator are presented. This improved simulator has been used for the study of the low tension pilot project at the Big Muddy field near Casper, Wyoming. Both the tracer injection conducted prior to the injection of the chemical slug, and the chemical flooding stages of the pilot project, have been analyzed. Not only the oil recovery but also the tracers, polymer, alcohol and chloride histories have been successfully matched with field results. Simulation results indicatemore » that, for this fresh water reservoir, the salinity gradient during the preflush and the resulting calcium pickup by the surfactant slug played a major role in the success of the project. In addition, analysis of the effects of the crossflow on the performance of the pilot project indicates that, for the well spacing of the pilot, crossflow does not play as important a role as it might for a large-scale project. To improve the numerical efficiency of the simulator, a third order convective differencing scheme has been applied to the simulator. This method can be used with non-uniform mesh, and therefore is suited for simulation studies of large-scale multiwell heterogeneous reservoirs. Comparison of the results with one and two dimensional analytical solutions shows that this method is effective in eliminating numerical dispersion using relatively large grid blocks. Results of one, two and three-dimensional miscible water/tracer flow, water flooding, polymer flooding, and micellar-polymer flooding test problems, and results of grid orientation studies, are presented.« less

Cardiac data increase association between self-report and both expert ratings of task load and task performance in flight simulator tasks: An exploratory study.

PubMed

Lehrer, Paul; Karavidas, Maria; Lu, Shou-En; Vaschillo, Evgeny; Vaschillo, Bronya; Cheng, Andrew

2010-05-01

Seven professional airplane pilots participated in a one-session test in a Boeing 737-800 simulator. Mental workload for 18 flight tasks was rated by experienced test pilots (hereinafter called "expert ratings") and by study participants' self-report on NASA's Task Load Index (TLX) scale. Pilot performance was rated by a check pilot. The standard deviation of R-R intervals (SDNN) significantly added 3.7% improvement over the TLX in distinguishing high from moderate-load tasks and 2.3% improvement in distinguishing high from combined moderate and low-load tasks. Minimum RRI in the task significantly discriminated high- from medium- and low-load tasks, but did not add significant predictive variance to the TLX. The low-frequency/high-frequency (LF:HF) RRI ratio based on spectral analysis of R-R intervals, and ventricular relaxation time were each negatively related to pilot performance ratings independently of TLX values, while minimum and average RRI were positively related, showing added contribution of these cardiac measures for predicting performance. Cardiac results were not affected by controlling either for respiration rate or motor activity assessed by accelerometry. The results suggest that cardiac assessment can be a useful addition to self-report measures for determining flight task mental workload and risk for performance decrements. Replication on a larger sample is needed to confirm and extend the results. Copyright 2010 Elsevier B.V. All rights reserved.

A hybrid froth flotation-filtration system as a pretreatment for oil sands tailings pond recycle water management: Bench- and pilot-scale studies.

PubMed

Loganathan, Kavithaa; Bromley, David; Chelme-Ayala, Pamela; Gamal El-Din, Mohamed

2015-09-15

Through sustainable water management, oil sands companies are working to reduce their reliance on fresh water by minimizing the amount of water required for their operations and by recycling water from tailings ponds. This study was the first pilot-scale testing of a hybrid technology consisting of froth flotation combined with filtration through precoated submerged stainless steel membranes used to treat recycle water from an oil sands facility. The results indicated that the most important factor affecting the performance of the hybrid system was the influent water quality. Any rise in the levels of suspended solids or total organic carbon of the feed water resulted in changes of chemical consumption rates, flux rates, and operating cycle durations. The selections of chemical type and dosing rates were critical in achieving optimal performance. In particular, the froth application rate heavily affected the overall recovery of the hybrid system as well as the performance of the flotation process. Optimum surfactant usage to generate froth (per liter of treated water) was 0.25 mL/L at approximately 2000 NTU of influent turbidity and 0.015 mL/L at approximately 200 NTU of influent turbidity. At the tested conditions, the optimal coagulant dose was 80 mg/L (as Al) at approximately 2000 NTU of influent turbidity and <40 mg/L (as Al) at approximately 200 NTU of influent turbidity. Precoat loading per unit membrane surface area tested during the pilot study was approximately 30 g/m(2). The results of this study indicated that this hybrid technology can potentially be considered as a pre-treatment step for reverse osmosis treatment of recycle water. Copyright © 2015 Elsevier Ltd. All rights reserved.

A small-group functional balance intervention for individuals with Alzheimer disease: a pilot study.

PubMed

Ries, Julie D; Drake, Jamie Michelle; Marino, Christopher

2010-03-01

Individuals with Alzheimer disease (AD) have a higher risk of falls than their cognitively intact peers. This pilot study was designed to assess the feasibility and effectiveness of a small-group balance exercise program for individuals with AD in a day center environment. Seven participants met the inclusion criteria: diagnosis of AD or probable AD, medical stability, and ability to walk (with or without assistive device). We used an exploratory pre- and post-test study design. Participants engaged in a functional balance exercise program in two 45-minute sessions each week for eight weeks. Balance activities were functional and concrete, and the intervention was organized into constant, blocked, massed practice. Outcome measures included Berg Balance Scale (BBS), Timed Up and Go (TUG), and gait speed (GS; self-selected and fast assessed by an instrumented walkway). Data were analyzed by comparing individual change scores with previously identified minimal detectable change scores at the 90% confidence level (MDC90). Pre- and post-test data were acquired for five participants (two participants withdrew). The BBS improved in all five participants, and improved > or = 6.4 points (the MDC90 for the BBS in three participants. Four participants improved their performance on the TUG, and three participants improved > or = 4.09 seconds (the MDC90 for the TUG). Self-selected GS increased > or = 9.44 cm/sec (the MDC90 for gait speed) in three participants. Two participants demonstrated post-test self-selected GS comparable with their pretest fast GS. This pilot study suggests that a small-group functional balance intervention for individuals with AD is feasible and effective. Although participants had no explicit memory of the program, four of five improved in at least two outcome measures. Larger scale functional balance intervention studies with individuals with AD are warranted.

Pilot scale treatment of chromite ore processing residue using sodium sulfide in single reduction and coupled reduction/stabilization processes.

PubMed

Velasco, Antonio; Ramírez, Martha; Hernández, Sergio; Schmidt, Winfried; Revah, Sergio

2012-03-15

Single Cr(VI) reduction and coupled reduction/stabilization (R/S) processes were evaluated at pilot scale to determine their effectiveness to treat chromite ore processing residue (COPR). Sodium sulfide was used as the reducing agent and cement, gypsum and lime were tested as the stabilizing agents. The pilot experiments were performed in a helical ribbon blender mixer with batches of 250 kg of COPR and mixing time up to 30 min. Na2S/Cr(VI) mass ratios of 4.6, 5.7 and 6.8 were evaluated in the single reduction process to treat COPR with Cr(VI) concentration of ≈4.2 g/kg. The R/S process was tested with a Na2S/Cr(VI) mass ratio of 5.7 and including stabilizing agents not exceeding 5% (w/w(COPR)), to treat COPR with a Cr(VI) content of ≈5.1g/kg. The single reduction process with a ratio of 6.8, reached Cr(VI) reduction efficiencies up to 97.6% in the first days, however these values decreased to around 93% after 380 days of storage. At this point the total Cr level was around 12.5 mg/L. Cr(VI) removal efficiencies exceeding 96.5% were reached and maintained during 380 days when the coupled R/S process was evaluated. Total Cr levels lower than 5 mg/l were attained at the initials days in all R/S batch tested, however after 380 days, concentrations below the regulatory limit were only found with gypsum (2%) as single agent and with a blend of cement (4%) and lime (1%). These results indicated that the coupled R/S process is an excellent alternative to stabilize COPR. Copyright © 2011 Elsevier B.V. All rights reserved.

14 CFR 61.307 - What tests do I have to take to obtain a sport pilot certificate?

Code of Federal Regulations, 2014 CFR

2014-01-01

... sport pilot certificate? 61.307 Section 61.307 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... INSTRUCTORS Sport Pilots § 61.307 What tests do I have to take to obtain a sport pilot certificate? To obtain a sport pilot certificate, you must pass the following tests: (a) Knowledge test. You must pass a...

14 CFR 61.307 - What tests do I have to take to obtain a sport pilot certificate?

Code of Federal Regulations, 2012 CFR

2012-01-01

... sport pilot certificate? 61.307 Section 61.307 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... INSTRUCTORS Sport Pilots § 61.307 What tests do I have to take to obtain a sport pilot certificate? To obtain a sport pilot certificate, you must pass the following tests: (a) Knowledge test. You must pass a...

14 CFR 61.307 - What tests do I have to take to obtain a sport pilot certificate?

Code of Federal Regulations, 2013 CFR

2013-01-01

... sport pilot certificate? 61.307 Section 61.307 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... INSTRUCTORS Sport Pilots § 61.307 What tests do I have to take to obtain a sport pilot certificate? To obtain a sport pilot certificate, you must pass the following tests: (a) Knowledge test. You must pass a...

Solar photo-Fenton treatment of carbofuran: analysis of mineralization, toxicity, and organic by-products.

PubMed

Lopez-Alvarez, Blady; Torres-Palma, Ricardo A; Ferraro, Franklin; Peñuela, Gustavo

2012-01-01

The degradation of the pesticide carbofuran (CBF) using solar photo-Fenton treatment, at both the laboratory and the pilot scale, was evaluated. At the laboratory scale, in a suntest reactor, the Fe(2+) concentration and H(2)O(2) concentration were evaluated and optimized using the surface response methodology and the Pareto diagram. Under optimal conditions experiments were performed to evaluate the evolution of the substrate removal, oxidation, subsequent mineralization, toxicity and the formation of chloride ions during the treatment. The analysis and evolution of five CBF by-products as well as several control and reactivity tests at the density functional theory level were used to depict a general scheme of the main degradation pathway of CBF via the photo-Fenton system. Finally, at the pilot scale, a sample of the commercial CBF product Furadan was eliminated after 420 min by the photo-Fenton system using direct sunlight. Under these conditions, after 900 min 89% of toxicity (1/E(50) on Vibrio fischeri bacteria), 97% of chemical oxygen demand, and 90% of dissolved organic carbon were removed.

Phosphate removal in agro-industry: pilot- and full-scale operational considerations of struvite crystallization.

PubMed

Moerman, Wim; Carballa, Marta; Vandekerckhove, Andy; Derycke, Dirk; Verstraete, Willy

2009-04-01

Pilot-scale struvite crystallization tests using anaerobic effluent from potato processing industries were performed at three different plants. Two plants (P1 & P2) showed high phosphate removal efficiencies, 89+/-3% and 75+/-8%, resulting in final effluent levels of 12+/-3 mg PO(4)(3-)-PL(-1) and 11+/-3mg PO(4)(3-)-PL(-1), respectively. In contrast, poor phosphate removal (19+/-8%) was obtained at the third location (P3). Further investigations at P3 showed the negative effect of high Ca(2+)/PO(4)(3-)-P molar ratio (ca. 1.25+/-0.11) on struvite formation. A full-scale struvite plant treating anaerobic effluent from a dairy industry showed the same Ca(2+) interference. A shift in the influent Ca(2+)/PO(4)(3-)-P molar ratio from 2.69 to 1.36 resulted in average total phosphorus removal of 78+/-7%, corresponding with effluent levels of 14+/-4 mg P(total)L(-1) (9+/-3 mg PO(4)(3-)-PL(-1)). Under these conditions high quality spherical struvite crystals of 2-6mm were produced.

Cocurrent scrubber evaluation: TVA's Colbert lime-limestone wet-scrubbing pilot plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hollinden, G.A.; Robards, R.F.; Moore, N.D.

1979-01-01

The Tennessee Valley Authority (TVA) is actively engaged in a pilot plant program to develop and/or evaluate wet-scrubbing processes for removing sulfur dioxide (SO/sub 2/) from boiler flue gas. The physical size and general arrangement of flue gas scrubbing systems have a major impact on capital investment and operating cost, as do potential operating and maintenance advantages inherent to some systems. The equipment configuration for a cocurrent scrubber reflects some of these advantages. EPRI funded TVA to perform preliminary screening tests at TVA's 1 MW pilot plant (Colbert Steam Plant) to develop operating data on the cocurrent design for usemore » in designing and operating a 10 MW prototype cocurrent scrubber at TVA's Shawnee Scrubber Test Facility. Results of Colbert tests showed excellent sulfur dioxide removal efficiencies, generally greater than 85%, low pressure drop, and high particulate removal efficiencies. This report covers these screening tests. The results indicate that commercial application of the cocurrent scrubber concept may save substantial capital investment by reducing the number of scrubber modules and auxiliary equipment. These evaluation tests provided the basis for the design and construction of the 10 MW cocurrent scrubber at the Shawnee Facility. Operation of this scrubber began in August 1978 to develop the scale-up similarities and differences between the Colbert test program (1 MW) and the Shawnee test program (10 MW). It also demonstrated the practicality and reliability of the 10 MW prototype. Detailed results of the prototype test series will be available in late 1979.« less

ORGANIC EMISSIONS FROM PILOT-SCALE INCINERATION OF CFCS

EPA Science Inventory

The paper gives results of the characterization of organic emissions resulting from the pilot-scale incineration of trichlorofluoromethane (CFC-11) and dichlorodifluoromethane (CFC-12) under varied feed concentrations. (NOTE: As a result of the Montreal Protocol, an international...

Low-nitrogen oxides combustion of dried sludge using a pilot-scale cyclone combustor with recirculation.

PubMed

Shim, Sung Hoon; Jeong, Sang Hyun; Lee, Sang-Sup

2015-04-01

Recently, numerical and experimental studies have been conducted to develop a moderate or intense low-oxygen dilution (MILD) combustion technology for solid fuels. The study results demonstrated that intense recirculation inside the furnace by high-momentum air is a key parameter to achieve the MILD combustion of solid fuels. However, the high-velocity air requires a significant amount of electricity consumption. A cyclone-type MILD combustor was therefore designed and constructed in the authors' laboratory to improve the recirculation inside the combustor. The laboratory-scale tests yielded promising results for the MILD combustion of dried sewage sludge. To achieve pilot-scale MILD combustion of dried sludge in this study, the effects of geometric parameters such as the venturi tube configuration, the air injection location, and the air nozzle diameter were investigated. With the optimized geometric and operational conditions, the pilot-scale cyclone combustor demonstrated successful MILD combustion of dried sludge at a rate of 75 kg/hr with an excess air ratio of 1.05. A horizontal cyclone combustor with recirculation demonstrated moderate or intense low-oxygen dilution (MILD) combustion of dried sewage sludge at a rate of 75 kg/hr. Optimizing only geometric and operational conditions of the combustor reduced nitrogen oxide (NOx) emissions to less than 75 ppm. Because the operating cost of the MILD combustor is much lower than that of the selective catalytic reduction (SCR) applied to the conventional combustor, MILD combustion technology with the cyclone type furnace is an eligible option for reducing NOx emissions from the combustion of dried sewage sludge.

Cooperative Collision Avoidance Step 1 - Technology Demonstration Flight Test Report. Revision 1

NASA Technical Reports Server (NTRS)

Trongale, Nicholas A.

2006-01-01

The National Aeronautics and Space Administration (NASA) Access 5 Project Office sponsored a cooperative collision avoidance flight demonstration program for unmanned aircraft systems (UAS). This flight test was accomplished between September 21st and September 27th 2005 from the Mojave Airport, Mojave, California. The objective of these flights was to collect data for the Access 5 Cooperative Collision Avoidance (CCA) Work Package simulation effort, i.e., to gather data under select conditions to allow validation of the CCA simulation. Subsequent simulation to be verified were: Demonstrate the ability to detect cooperative traffic and provide situational awareness to the ROA pilot; Demonstrate the ability to track the detected cooperative traffic and provide position information to the ROA pilot; Demonstrate the ability to determine collision potential with detected cooperative traffic and provide notification to the ROA pilot; Demonstrate that the CCA subsystem provides information in sufficient time for the ROA pilot to initiate an evasive maneuver to avoid collision; Demonstrate an evasive maneuver that avoids collision with the threat aircraft; and lastly, Demonstrate the ability to assess the adequacy of the maneuver and determine that the collision potential has been avoided. The Scaled Composites, LLC Proteus Optionally Piloted Vehicle (OPV) was chosen as the test platform. Proteus was manned by two on-board pilots but was also capable of being controlled from an Air Vehicle Control Station (AVCS) located on the ground. For this demonstration, Proteus was equipped with cooperative collision sensors and the required hardware and software to place the data on the downlink. Prior to the flight phase, a detailed set of flight test scenarios were developed to address the flight test objectives. Two cooperative collision avoidance sensors were utilized for detecting aircraft in the evaluation: Traffic Alert and Collision Avoidance System-II (TCAS-II) and Automatic Dependent Surveillance Broadcast (ADS-B). A single intruder aircraft was used during all the flight testing, a NASA Gulfstream III (G-III). During the course of the testing, six geometrically different near-collision scenarios were evaluated. These six scenarios were each tested using various combinations of sensors and collision avoidance software. Of the 54 planned test points 49 were accomplished successfully. Proteus flew a total of 21.5 hours during the testing and the G-III flew 19.8 hours. The testing fully achieved all flight test objectives. The Flight IPT performed an analysis to determine the accuracy of the simulation model used to predict the location of the host aircraft downstream during an avoidance maneuver. The data collected by this flight program was delivered to the Access 5 Cooperative Collision Avoidance (CCA) Work Package Team who was responsible for reporting on their analysis of this flight data.

Consolidated fuel reprocessing program

NASA Astrophysics Data System (ADS)

1985-02-01

Improved processes and components for the Breeder Reprocessing Engineering Test (BRET) were identified and developed as well as the design, procurement and development of prototypic equipment. The integrated testing of process equipment and flowsheets prototypical of a pilot scale full reprocessing plant, and also for testing prototypical remote features of specific complex components in the system are provided. Information to guide the long range activities of the Consolidated Fuel Reprocessing Program (CERP), a focal point for foreign exchange activities, and support in specialized technical areas are described. Research and development activities in HTGR fuel treatment technology are being conducted. Head-end process and laboratory scale development efforts, as well as studies specific to HTGR fuel, are reported. The development of off-gas treatment processes has generic application to fuel reprocessing, progress in this work is also reported.

Patent foramen ovale and asymptomatic brain lesions in military fighter pilots.

PubMed

Kang, Kyung Wook; Kim, Joon-Tae; Choi, Won-Ho; Park, Won-Ju; Shin, Young Ho; Choi, Kang-Ho

2014-10-01

Previous studies have reported higher incidence of white matter lesions (WMLs) in military pilots. The anti-gravity straining maneuver, which fighter military pilots perform numerously during a flight is identical to the valsalva maneuver. We sought to investigate the prevalence of right-to-left shunt (RLS) associated with WMLs in military pilots. A prospective study was performed involving military pilots who visited the Airomedical Center. The pilots underwent brain magnetic resonance imaging (MRI) scan and transcranial Doppler (TCD) with intravenous injection of agitated saline solution for the detection of RLS. Periventricular WMLs (PVWMLs) on MRI were graded using Fazeka's scale, and deep WMLs (DWMLs) were graded using Scheltens's scale. This study included 81 military pilots. RLS on TCD was observed less frequently in non-fighter pilots than in fighter pilots (35.5% vs. 64.5%, p=0.011). Fighter pilot was an independently associated factor with RLS on the TCD. DWMLs were independently associated with RLSs through a patent foramen ovale (PFO) (OR 3.507, 95% CI 1.223-10.055, p=0.02). The results suggest that DWMLs in military pilots may significantly be associated with RLS via PFO. Additional investigations are warranted. Copyright © 2014 Elsevier B.V. All rights reserved.

PILOT-SCALE STUDIES ON THE INCINERATION OF ELECTRONICS INDUSTRY WASTE

EPA Science Inventory

The paper describes experiments performed on a pilot-scale rotary kiln incinerator to investigate the emissions and operational behavior during the incineration of consumer electronics waste. These experiments were targeted at destroying the organic components of printed circuit ...

Interaction of feel system and flight control system dynamics on lateral flying qualities

NASA Technical Reports Server (NTRS)

Bailey, Randall E.; Powers, Bruce G.; Shafer, Mary F.

1988-01-01

An investigation of feel system and flight control system dynamics on lateral flying qualities was conducted using the variable stability USAF NT-33 aircraft. Experimental variations in feel system natural frequency, force-deflection gradient, control system command architecture type, flight control system filter frequency, and control system delay were made. The experiment data include pilot ratings using the Cooper-Harper (1969) rating scale, pilot comments, and tracking performance statistic. Three test pilots served as evaluators. The data indicate that as the feel system natural frequency is reduced lateral flying qualities degrade. At the slowest feel system frequency, the closed-loop response becomes nonlinear with a 'bobweight' effect apparent in the feel system. Feel system influences were essentially independent of the control system architecture. The flying qualities influence due to the feel system was different than when the identical dynamic systenm was used as a flight control system element.

Flight investigation of cockpit-displayed traffic information utilizing coded symbology in an advanced operational environment

NASA Technical Reports Server (NTRS)

Abbott, T. S.; Moen, G. C.; Person, L. H., Jr.; Keyser, G. L., Jr.; Yenni, K. R.; Garren, J. F., Jr.

1980-01-01

Traffic symbology was encoded to provide additional information concerning the traffic, which was displayed on the pilot's electronic horizontal situation indicators (EHSI). A research airplane representing an advanced operational environment was used to assess the benefit of coded traffic symbology in a realistic work-load environment. Traffic scenarios, involving both conflict-free and conflict situations, were employed. Subjective pilot commentary was obtained through the use of a questionnaire and extensive pilot debriefings. These results grouped conveniently under two categories: display factors and task performance. A major item under the display factor category was the problem of display clutter. The primary contributors to clutter were the use of large map-scale factors, the use of traffic data blocks, and the presentation of more than a few airplanes. In terms of task performance, the cockpit-displayed traffic information was found to provide excellent overall situation awareness. Additionally, mile separation prescribed during these tests.

14 CFR 91.1065 - Initial and recurrent pilot testing requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Initial and recurrent pilot testing... Ownership Operations Program Management § 91.1065 Initial and recurrent pilot testing requirements. (a) No program manager or owner may use a pilot, nor may any person serve as a pilot, unless, since the beginning...

14 CFR 91.1065 - Initial and recurrent pilot testing requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 2 2011-01-01 2011-01-01 false Initial and recurrent pilot testing... Ownership Operations Program Management § 91.1065 Initial and recurrent pilot testing requirements. (a) No program manager or owner may use a pilot, nor may any person serve as a pilot, unless, since the beginning...

Intensive mothering ideology in France: A pilot study.

PubMed

Loyal, D; Sutter Dallay, A-L; Rascle, N

2017-12-01

The aim of this pilot study was to adapt the intensive mothering ideology concept in a French sample and to get an assessment tool. First, the Intensive Parenting Attitudes Questionnaire (IPAQ), a U.S. scale comprising 25 items, was translated and submitted online to French mothers and mothers-to-be (n=250). Structural validity was tested through confirmatory factor analysis with poor results. Secondly, to increase the cultural validity of a new tool, new items were derived from French women speech. French mothers and mothers-to-be (n=22) were asked about their views regarding motherhood and childcare (semi-structured interviews). A thematic content analysis was performed with good inter-judge agreement (0.53-0.86) and 27 items were created. Finally, the total set of 52 items was submitted online to French mothers and mothers-to-be (n=474). The structure was tested through exploratory factor analysis. A new tool called the Measure of Intensive Mothering Ideology (MIMI) was obtained. This 21 items scale with 6 dimensions (Essentialism, Consuming Fulfillment, Child-centrism, Challenge, Sacrifice and Stimulation) explains 59.75% of variance. Internal consistencies were satisfactory (0.61-0.83) and most dimensions were positively and moderately correlated (0.17-0.38). The MIMI is the first French-language scale assessing IMI and offers interesting research avenues notably regarding perinatal parental adaptation. Copyright © 2017 L'Encéphale, Paris. Published by Elsevier Masson SAS. All rights reserved.

Interdisciplinary Interactions within a Small-Scale Research Initiative Investigating Animation Creation as a Means of Teaching and Learning

ERIC Educational Resources Information Center

Wishart, J. M.; Wakley, G.

2017-01-01

This paper reports an interdisciplinary research (IDR) initiative conducted by two lecturers from different university faculties who found they shared an interest in using animations to support teaching and learning. The research comprised an exploratory pilot to test the feasibility, and to explore the impact on learning, of having undergraduates…

Evaluation of wood bonding performance of water-washed cottonseed meal-based adhesives with high solid contents and low press temperatures

USDA-ARS?s Scientific Manuscript database

Water-washed cottonseed meal (WCSM) has been shown as a promising bio-based wood adhesive. Recently, we prepared WCSM on a pilot scale for promotion of its industrial application. In this work, we tested the bonding strength of WCSM slurries with high solid contents and low press temperatures per i...

Development and Application of Environmental Quality of Life Scale among People Residing near Three Types of Industrial Areas, Southern Thailand

ERIC Educational Resources Information Center

Sopsuk, Jirawan; Chongsuvivatwong, Virasakdi; Sornsrivichai, Vorasith; Hasuwanakit, Supat

2013-01-01

To compare QOL among rural people living in three different industrial areas and one non-industrial area in southern Thailand. A questionnaire based on the WHOQOL-BREF with environmental assessment was initially developed. After consultation with experts and pilot study, it was tested to check internal reliability and further modified as…

Intermittent theta-burst transcranial magnetic stimulation for autism spectrum disorder: an open-label pilot study.

PubMed

Abujadi, Caio; Croarkin, Paul E; Bellini, Bianca B; Brentani, Helena; Marcolin, Marco A

2017-12-11

Theta-burst stimulation (TBS) modulates synaptic plasticity more efficiently than standard repetitive transcranial magnetic stimulation delivery and may be a promising modality for neuropsychiatric disorders such as autism spectrum disorder (ASD). At present there are few effective interventions for prefrontal cortex dysfunction in ASD. We report on an open-label, pilot study of intermittent TBS (iTBS) to target executive function deficits and restricted, repetitive behaviors in male children and adolescents with ASD. Ten right-handed, male participants, aged 9-17 years with ASD were enrolled in an open-label trial of iTBS treatment. Fifteen sessions of neuronavigated iTBS at 100% motor threshold targeting the right dorsolateral prefrontal cortex were delivered over 3 weeks. Parent report scores on the Repetitive Behavior Scale Revised and the Yale-Brown Obsessive Compulsive Scale demonstrated improvements with iTBS treatment. Participants demonstrated improvements in perseverative errors on the Wisconsin Card Sorting Test and total time for the Stroop test. The iTBS treatments were well tolerated with no serious adverse effects. These preliminary results suggest that further controlled interventional studies of iTBS for ASD are warranted.

Cross-cultural adaptation of the Individual Work Performance Questionnaire.

PubMed

Koopmans, Linda; Bernaards, Claire M; Hildebrandt, Vincent H; Lerner, Debra; de Vet, Henrica C W; van der Beek, Allard J

2015-01-01

The Individual Work Performance Questionnaire (IWPQ), measuring task performance, contextual performance, and counterproductive work behavior, was developed in The Netherlands. To cross-culturally adapt the IWPQ from the Dutch to the American-English language, and assess the questionnaire's internal consistency and content validity in the American-English context. A five stage translation and adaptation process was used: forward translation, synthesis, back-translation, expert committee review, and pilot-testing. During the pilot-testing, cognitive interviews with 40 American workers were performed, to examine the comprehensibility, applicability, and completeness of the American-English IWPQ. Questionnaire instructions were slightly modified to aid interpretation in the American-English language. Inconsistencies with verb tense were identified, and it was decided to consistently use simple past tense. The wording of five items was modified to better suit the American-English language. In general, participants were positive on the comprehensibility, applicability and completeness of the questionnaire during the pilot-testing phase. Furthermore, the study showed positive results concerning the internal consistency (Cronbach's alphas for the scales between 0.79-0.89) and content validity of the American-English IWPQ. The results indicate that the cross-cultural adaptation of the American-English IWPQ was successful and that the measurement properties of the translated version are promising.

Development and pilot testing of a psychosocial intervention program for young breast cancer survivors.

PubMed

Ahmed, Kauser; Marchand, Erica; Williams, Victoria; Coscarelli, Anne; Ganz, Patricia A

2016-03-01

To describe the development, pilot testing, and dissemination of a psychosocial intervention addressing concerns of young breast cancer survivors (YBCS). Intervention development included needs assessment with community organizations and interviews with YBCS. Based on evidence-based models of treatment, the intervention included tools for managing anxiety, fear of recurrence, tools for decision-making, and coping with sexuality/relationship issues. After pilot testing in a university setting, the program was disseminated to two community clinical settings. The program has two distinct modules (anxiety management and relationships/sexuality) that were delivered in two sessions; however, due to attrition, an all day workshop evolved. An author constructed questionnaire was used for pre- and post-intervention evaluation. Post-treatment scores showed an average increase of 2.7 points on a 10 point scale for the first module, and a 2.3 point increase for the second module. Qualitative feedback surveys were also collected. The two community sites demonstrated similar gains among their participants. The intervention satisfies an unmet need for YBCS and is a possible model of integrating psychosocial intervention with oncology care. This program developed standardized materials which can be disseminated to other organizations and potentially online for implementation within community settings. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Resource conservation and recovery act draft hazardous waste facility permit: Waste Isolation Pilot Plant (WIPP). Attachments: Volume 4 of 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-08-01

Volume IV contains the following attachments for Module IV: VOC monitoring plan for bin-room tests (Appendix D12); bin emission control and VOC monitoring system drawings; bin scale test room ventilation drawings; WIPP supplementary roof support system, underground storage area, room 1, panel 1, DOE/WIPP 91-057; and WIPP supplementary roof support system, room 1, panel 1, geotechnical field data analysis bi-annual report, DOE/WIPP 92-024.

Contribution of assimilable organic carbon to biological fouling in seawater reverse osmosis membrane treatment.

PubMed

Weinrich, Lauren; LeChevallier, Mark; Haas, Charles N

2016-09-15

Biological fouling occurs on RO membranes when bacteria and nutrients are present in conditions that are conducive to growth and proliferation of the bacteria. Controlling microbial growth on the membranes is typically limited to biocide application (i.e., disinfectants) in seawater RO plants. However, biological growth and subsequent fouling has not been well-managed. Pretreatment has not been focused on nutrient limitation. This project used a biological assay, the assimilable organic carbon (AOC) test to evaluate pretreatment effects on the nutrient supply. The AOC test provided a useful surrogate measurement for the biodegradability or biofouling potential of RO feed water. Biofouling observed in controlled conditions at the bench- and pilot-scale resulted in statistically significant correlations between AOC and the operational effects caused by biofouling. Membrane fouling rates are observed through operational changes over time such as increased differential pressure between the membrane feed and concentrate locations and decreased permeate flux through the membrane. In full scale plants there were strong correlations when AOC was used as a predictor variable for increased differential pressure (0.28-0.55 bar from September-December 2012) and decreased specific flux (1.40 L per hour/(m(2) · bar)). Increased differential pressure was associated with RO membrane biological fouling when the median AOC was 50 μg/L during pilot testing. Conditions were also evaluated at the bench-scale using a flat sheet RO membrane. In a comparison test using 30 and 1000 μg/L AOC, fouling was detected on more portions of the membrane when AOC was higher. Biofilm and bacterial deposits were apparent from scanning electron microscope imaging and biomass measurements using ATP. Copyright © 2016 Elsevier Ltd. All rights reserved.

Commercial Pilot Knowledge Test Guide

DOT National Transportation Integrated Search

1995-01-01

The FAA has available hundreds of computer testing centers nationwide. These testing centers offer the full range of airman knowledge tests including military competence, instrument foreign pilot, and pilot examiner predesignated tests. Refer to appe...

From community-based pilot testing to region-wide systems change: lessons from a local quality improvement collaborative.

PubMed

Keyser, Donna J; Pincus, Harold Alan

2010-01-01

A community-based collaborative conducted a 2-year pilot study to inform efforts for improving maternal and child health care practice and policy in Allegheny County, Pennsylvania. (1) To test whether three small-scale versions of an evidence-based, systems improvement approach would be workable in local community settings and (2) to identify specific policy/infrastructure reforms for sustaining improvements. A mixed methods approach was used, including quantitative performance measurement supplemented with qualitative data about factors related to outcomes of interest, as well as key stakeholder interviews and a literature review/Internet search. Quantitative performance results varied; qualitative data revealed critical factors for the success and failure of the practices tested. Policy/infrastructure recommendations were developed to address specific practice barriers. This information was important for designing a region-wide quality improvement initiative focused on maternal depression. The processes and outcomes provide valuable insights for other communities interested in conducting similar quality improvement initiatives.

Development and pilot testing the Family Conference Rating Scale: A tool aimed to assess interprofessional patient-centred communication and collaboration competencies.

PubMed

Dojeiji, Sue; Byszewski, Anna; Wood, Tim

2015-01-01

There is a paucity of evidence-based literature on the essential communication and collaboration skills to guide health care teams in conducting and assessing their performance in the Family Conference (FC). The authors developed and collected validity evidence for a rating scale of team FC performance, the Family Conference Rating Scale (FCRS). In phase 1, essential FC communication and collaboration skills were identified through a review of existing communication tools and literature on team functioning; a draft 34-item scale was developed. In phase 2, the scale was narrowed to a 6-category, 9-point scale with descriptors of expected behaviours through an iterative process: testing of the scale on 10 FC transcripts by two experts, soliciting feedback from a focus group of seven health care providers, and testing by non-experts on 49 live FCs. In phase 3, scores on the revised scale were validated by 10 health care providers from different disciplines by rating three videos of FCs of variable quality. Raters were able to detect inter-video variation in FC quality. The reliability of the FCRS was 0.95 and the inter-rater reliability, 0.68. The FCRS may enhance the ability of health professions educators to teach and assess interprofessional patient-centred communication and collaboration competencies.

Selenium Speciation and Management in Wet FGD Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Searcy, K; Richardson, M; Blythe, G

2012-02-29

This report discusses results from bench- and pilot-scale simulation tests conducted to determine the factors that impact selenium speciation and phase partitioning in wet FGD systems. The selenium chemistry in wet FGD systems is highly complex and not completely understood, thus extrapolation and scale-up of these results may be uncertain. Control of operating parameters and application of scrubber additives have successfully demonstrated the avoidance or decrease of selenite oxidation at the bench and pilot scale. Ongoing efforts to improve sample handling methods for selenium speciation measurements are also discussed. Bench-scale scrubber tests explored the impacts of oxidation air rate, tracemore » metals, scrubber additives, and natural limestone on selenium speciation in synthetic and field-generated full-scale FGD liquors. The presence and concentration of redox-active chemical species as well as the oxidation air rate contribute to the oxidation-reduction potential (ORP) conditions in FGD scrubbers. Selenite oxidation to the undesirable selenate form increases with increasing ORP conditions, and decreases with decreasing ORP conditions. Solid-phase manganese [Mn(IV)] appeared to be the significant metal impacting the oxidation of selenite to selenate. Scrubber additives were tested for their ability to inhibit selenite oxidation. Although dibasic acid and other scrubber additives showed promise in early clear liquor (sodium based and without calcium solids) bench-scale tests, these additives did not show strong inhibition of selenite oxidation in tests with higher manganese concentrations and with slurries from full-scale wet FGD systems. In bench-tests with field liquors, addition of ferric chloride at a 250:1 iron-to-selenium mass ratio sorbed all incoming selenite to the solid phase, although addition of ferric salts had no impact on native selenate that already existed in the field slurry liquor sample. As ORP increases, selenite may oxidize to selenate more rapidly than it sorbs to ferric solids. Though it was not possible to demonstrate a decrease in selenium concentrations to levels below the project'ale testing were evident at the pilot scale. Specifically, reducing oxidation air rate and ORP tends to either retain selenium as selenite in the liquor or shift selenium phase partitioning to the solid phase. Oxidation air flow rate control may be one option for managing selenium behavior in FGD scrubbers. Units that cycle load widely may find it more difficult to impact ORP conditions with oxidation air flow rate control alone. Because decreasing oxidation air rates to the reaction tank showed that all new selenium reported to the solids, the addition of ferric chloride to the pilot scrubber could not show further improvements in selenium behavior. Ferric chloride addition did shift mercury to the slurry solids, specifically to the fine particles. Several competing pathways may govern the reporting of selenium to the slurry solids: co-precipitation with gypsum into the bulk solids and sorption or co-precipitation with iron into the fine particles. Simultaneous measurement of selenium and mercury behavior suggests a holistic management strategy is best to optimize the fate of both of these elements in FGD waters. Work conducted under this project evaluated sample handling and analytical methods for selenium speciation in FGD waters. Three analytical techniques and several preservation methods were employed. Measurements of selenium speciation over time indicated that for accurate selenium speciation, it is best to conduct measurements on unpreserved, filtered samples as soon after sampling as possible. The capital and operating costs for two selenium management strategies were considered: ferric chloride addition and oxidation air flow rate control. For ferric chloride addition, as might be expected the reagent makeup costs dominate the overall costs, and range from 0.22 to 0.29 mills/kWh. For oxidation air flow rate control, a cursory comparison of capital costs and turndown capabilities for multi-stage and single-stage centrifugal blowers and several flow control methods was completed. For greenfield systems, changing the selection of blower type and flow control method may have payback periods of 4 to 5 years or more if based on energy savings alone. However, the benefits to managing redox chemistry in the scrubber could far outweigh the savings in electricity costs under some circumstances.« less

A music quality rating test battery for cochlear implant users to compare the FSP and HDCIS strategies for music appreciation.

PubMed

Looi, Valerie; Winter, Philip; Anderson, Ilona; Sucher, Catherine

2011-08-01

The purpose of this study was to develop a music quality rating test battery (MQRTB) and pilot test it by comparing appraisal ratings from cochlear implant (CI) recipients using the fine-structure processing (FSP) and high-definition continuous interleaved sampling (HDCIS) speech processing strategies. The development of the MQRTB involved three stages: (1) Selection of test items for the MQRTB; (2) Verification of its length and complexity with normally-hearing individuals; and (3) Pilot testing with CI recipients. Part 1 involved 65 adult listeners, Part 2 involved 10 normally-hearing adults, and Part 3 involved five adult MED-EL CI recipients. The MQRTB consisted of ten songs, with ratings made on scales assessing pleasantness, naturalness, richness, fullness, sharpness, and roughness. Results of the pilot study, which compared FSP and HDCIS for music, indicated that acclimatization to a strategy had a significant effect on ratings (p < 0.05). When acclimatized to FSP, the group rated FSP as closer to 'exactly as I want it to sound' than HDCIS (p < 0.05), and that HDCIS sounded significantly sharper and rougher than FSP. However when acclimatized to HDCIS, there were no significant differences between ratings. There was no effect of song familiarity or genre on ratings. Overall the results suggest that the use of FSP as the default strategy for MED-EL recipients would have a positive effect on music appreciation, and that the MQRTB is an effective tool for assessing music sound quality.

Comparison of lab, pilot, and industrial scale low consistency mechanical refining for improvements in enzymatic digestibility of pretreated hardwood.

PubMed

Jones, Brandon W; Venditti, Richard; Park, Sunkyu; Jameel, Hasan

2014-09-01

Mechanical refining has been shown to improve biomass enzymatic digestibility. In this study industrial high-yield sodium carbonate hardwood pulp was subjected to lab, pilot and industrial refining to determine if the mechanical refining improves the enzymatic hydrolysis sugar conversion efficiency differently at different refining scales. Lab, pilot and industrial refining increased the biomass digestibility for lignocellulosic biomass relative to the unrefined material. The sugar conversion was increased from 36% to 65% at 5 FPU/g of biomass with industrial refining at 67.0 kWh/t, which was more energy efficient than lab and pilot scale refining. There is a maximum in the sugar conversion with respect to the amount of refining energy. Water retention value is a good predictor of improvements in sugar conversion for a given fiber source and composition. Improvements in biomass digestibility with refining due to lab, pilot plant and industrial refining were similar with respect to water retention value. Published by Elsevier Ltd.

Flight control systems development of highly maneuverable aircraft technology /HiMAT/ vehicle

NASA Technical Reports Server (NTRS)

Petersen, K. L.

1979-01-01

The highly maneuverable aircraft technology (HiMAT) program was conceived to demonstrate advanced technology concepts through scaled-aircraft flight tests using a remotely piloted technique. Closed-loop primary flight control is performed from a ground-based cockpit, utilizing a digital computer and up/down telemetry links. A backup flight control system for emergency operation resides in an onboard computer. The onboard systems are designed to provide fail-operational capabilities and utilize two microcomputers, dual uplink receiver/decoders, and redundant hydraulic actuation and power systems. This paper discusses the design and validation of the primary and backup digital flight control systems as well as the unique pilot and specialized systems interfaces.

Nurse competence scale: development and psychometric testing.

PubMed

Meretoja, Riitta; Isoaho, Hannu; Leino-Kilpi, Helena

2004-07-01

Self-assessment assists nurses to maintain and improve their practice by identifying their strengths and areas that may need to be further developed. Professional competence profiles encourage them to take an active part in the learning process of continuing education. Although competence recognition offers a way to motivate practising nurses to produce quality care, few measuring tools are available for this purpose. This paper describes the development and testing of the Nurse Competence Scale, an instrument with which the level of nurse competence can be assessed in different hospital work environments. The categories of the Nurse Competence Scale were derived from Benner's From Novice to Expert competency framework. A seven-step approach, including literature review and six expert groups, was used to identify and validate the indicators of nurse competence. After a pilot test, psychometric testing of the Nurse Competence Scale (content, construct and concurrent validity, and internal consistency) was undertaken with 498 nurses. The 73-item scale consists of seven categories, with responses on a visual analogy scale format. The frequency of using competencies was additionally tested with a four-point scale. Self-assessed overall scores indicated a high level of competence across categories. The Nurse Competence Scale data were normally distributed. The higher the frequency of using competencies, the higher was the self-assessed level of competence. Age and length of work experience had a positive but not very strong correlation with level of competence. According to the item analysis, the categories of the Nurse Competence Scale showed good internal consistency. The results provide strong evidence of the reliability and validity of the Nurse Competence Scale.

The Development and piloting of an eHealth breastfeeding resource targeting fathers and partners as co-parents.

PubMed

Abbass-Dick, Jennifer; Xie, Fangli; Koroluk, Jaymie; Alcock Brillinger, Shelley; Huizinga, Joanne; Newport, Amber; Goodman, William M; Dennis, Cindy-Lee

2017-07-01

Traditionally breastfeeding education programs target mothers solely. The objective of this study was to design and pilot test an interactive eHealth breastfeeding co-parenting resource developed to target both mothers and fathers. eHealth resources provide an accessible and engaging format on which to educate parents and assist them in meeting their breastfeeding goals. Best practices to design such resources are not currently known. A three phase pilot study was conducted. The three phases included conducting a needs assessment, creating the resource and pilot testing the resource with mother, father and health care professionals to determine their perspectives regarding the usability and design of the prototype resource. The interactive prototype resource was designed to provide information to parents on breastfeeding and co-parenting, which included suggestions on how fathers can be involved and support breastfeeding and how the couples can work as a team to meet their breastfeeding goals. Setting: Recruitment took place in a health region in Southern Ontario, Canada between June 2014 and March 2015. Online questionnaires were completed by participants in all phases of the study. Participants (n=149) were pregnant or new mothers and their partners in the health region who read and speak English and had access to the internet and health care professionals who work with breastfeeding families in Ontario, Canada. A prototype eHealth breastfeeding co-parenting resource was developed based on maternal and paternal feedback from Phase I and utilized an interactive interface which included games and multimodal information delivery. The prototype eHealth resource was provided to the parents in Phase II and health care professionals in Phase III. The final resource was created based on feedback from these participants. The resource was pilot tested with new and expectant parents using pre- and post-test questionnaires which included measures for breastfeeding self-efficacy (Breastfeeding Self-Efficacy Short Form), infant feeding attitude (Iowa Infant Feeding Attitude Scale), breastfeeding knowledge (Breastfeeding Knowledge Questionnaire) and co-parenting relationship (Co-parenting Relationship Scale). Maternal and paternal breastfeeding self-efficacy and knowledge and infant feeding attitude scores all increased from pre-test to post-test. However, there was no difference in the co-parenting relationship scores from pretest to post-test. This study has used feedback from parents and health professionals to develop a prototype resource which appears to be effective in increasing parents' breastfeeding knowledge, attitude and self-efficacy. The prototype resource was rated positively by parents and health care providers. An eHealth breastfeeding co-parenting resource designed with input from the target population is an effective way of providing information to mothers and fathers. Further research with a randomized controlled design and more diverse populations is needed to determine effectiveness of the resource on breastfeeding duration and exclusivity. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

A Collection of Nonlinear Aircraft Simulations in MATLAB

NASA Technical Reports Server (NTRS)

Garza, Frederico R.; Morelli, Eugene A.

2003-01-01

Nonlinear six degree-of-freedom simulations for a variety of aircraft were created using MATLAB. Data for aircraft geometry, aerodynamic characteristics, mass / inertia properties, and engine characteristics were obtained from open literature publications documenting wind tunnel experiments and flight tests. Each nonlinear simulation was implemented within a common framework in MATLAB, and includes an interface with another commercially-available program to read pilot inputs and produce a three-dimensional (3-D) display of the simulated airplane motion. Aircraft simulations include the General Dynamics F-16 Fighting Falcon, Convair F-106B Delta Dart, Grumman F-14 Tomcat, McDonnell Douglas F-4 Phantom, NASA Langley Free-Flying Aircraft for Sub-scale Experimental Research (FASER), NASA HL-20 Lifting Body, NASA / DARPA X-31 Enhanced Fighter Maneuverability Demonstrator, and the Vought A-7 Corsair II. All nonlinear simulations and 3-D displays run in real time in response to pilot inputs, using contemporary desktop personal computer hardware. The simulations can also be run in batch mode. Each nonlinear simulation includes the full nonlinear dynamics of the bare airframe, with a scaled direct connection from pilot inputs to control surface deflections to provide adequate pilot control. Since all the nonlinear simulations are implemented entirely in MATLAB, user-defined control laws can be added in a straightforward fashion, and the simulations are portable across various computing platforms. Routines for trim, linearization, and numerical integration are included. The general nonlinear simulation framework and the specifics for each particular aircraft are documented.

14 CFR 21.37 - Flight test pilot.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Flight test pilot. 21.37 Section 21.37... PROCEDURES FOR PRODUCTS AND PARTS Type Certificates § 21.37 Flight test pilot. Each applicant for a normal... holding an appropriate pilot certificate to make the flight tests required by this part. [Doc. No. 5085...

14 CFR 21.37 - Flight test pilot.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Flight test pilot. 21.37 Section 21.37... PROCEDURES FOR PRODUCTS AND PARTS Type Certificates § 21.37 Flight test pilot. Each applicant for a normal... holding an appropriate pilot certificate to make the flight tests required by this part. [Doc. No. 5085...

14 CFR 21.37 - Flight test pilot.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Flight test pilot. 21.37 Section 21.37... PROCEDURES FOR PRODUCTS AND PARTS Type Certificates § 21.37 Flight test pilot. Each applicant for a normal... holding an appropriate pilot certificate to make the flight tests required by this part. [Doc. No. 5085...

Shortcuts for Pilot Testing Instructional Materials.

ERIC Educational Resources Information Center

Howe, R. John; Pearlstein, Gloria

1995-01-01

A mini-pilot test was conducted by the Department of Labor's Employment Standards Administration to develop training on enforcing the Federal Family and Medical Leave Act. The situation that necessitated the test is presented; mini-pilot test examples are explained; and pros and cons of the mini-pilots are examined. A sidebar contains suggestions…

A clinico-biochemical evaluation of the role of a herbal (Ayurvedic) immunomodulator in chronic periodontal disease: a pilot study.

PubMed

Shetty, Shreya; Bose, Aditi; Sridharan, Srirangarajan; Satyanarayana, Aparna; Rahul, Aparna

2013-06-01

Host modulation is fast gaining popularity as a preferred therapeutic modality for periodontal disease. Recent research in the medical field into herbal immunomodulators such as Septilin® has spurred an interest in evaluating its efficacy in periodontitis for the first time. The aim of the study was to assess the immunomodulatory effects of the herbal immunomodulator Septilin® (Himalaya Drug Company, Bangalore, India) when used as an adjunct to scaling and root planing in chronic periodontal disease. Forty systemically healthy patients aged between 25 and 55 years of age and with chronic periodontitis were randomly divided into two groups. The test group was administered Septilin® tablets for two weeks following scaling and root planing whereas the control group was treated by scaling and root planing alone. Changes in gingival index (GI), gingival bleeding index (GBI), serum C-reactive protein (CRP) levels and salivary tumour necrosis factor-alpha (TNF-α) levels were assessed at day 0, at two weeks, and at three and six months. The GI and GBI showed a statistically significant reduction at two weeks, three months and six months (P<0.001) in both groups. Salivary TNF-α level reduction was significant in the test group only (P<0.001). No significant change was found in serum CRP levels in both groups (P>0.05). In this pilot evaluation, Septilin® was found to be a safe and effective immunomodulator as an adjunct to routine periodontal therapy. Further long-term studies to test Septilin® on larger sections of the population are recommended.

Control research in the NASA high-alpha technology program

NASA Technical Reports Server (NTRS)

Gilbert, William P.; Nguyen, Luat T.; Gera, Joseph

1990-01-01

NASA is conducting a focused technology program, known as the High-Angle-of-Attack Technology Program, to accelerate the development of flight-validated technology applicable to the design of fighters with superior stall and post-stall characteristics and agility. A carefully integrated effort is underway combining wind tunnel testing, analytical predictions, piloted simulation, and full-scale flight research. A modified F-18 aircraft has been extensively instrumented for use as the NASA High-Angle-of-Attack Research Vehicle used for flight verification of new methods and concepts. This program stresses the importance of providing improved aircraft control capabilities both by powered control (such as thrust-vectoring) and by innovative aerodynamic control concepts. The program is accomplishing extensive coordinated ground and flight testing to assess and improve available experimental and analytical methods and to develop new concepts for enhanced aerodynamics and for effective control, guidance, and cockpit displays essential for effective pilot utilization of the increased agility provided.

REBURNING THERMAL AND CHEMICAL PROCESSES IN A TWO-DIMENSIONAL PILOT-SCALE SYSTEM

EPA Science Inventory

The paper describes an experimental investigation of the thermal and chemical processes influencing NOx reduction by natural gas reburning in a two-dimensional pilot-scale combustion system. Reburning effectiveness for initial NOx levels of 50-500 ppm and reburn stoichiometric ra...

CHLORINE DECAY AND BIOFILM STUDIES IN A PILOT SCALE DRINKING WATER DISTRIBUTION DEAD END PIPE SYSTEM

EPA Science Inventory

Chlorine decay experiments using a pilot-scale water distribution dead end pipe system were conducted to define relationships between chlorine decay and environmental factors. These included flow rate, biomass concentration and biofilm density, and initial chlorine concentrations...

Development of a Social Skills Assessment Screening Scale for Psychiatric Rehabilitation Settings: A Pilot Study.

PubMed

Bhola, Poornima; Basavarajappa, Chethan; Guruprasad, Deepti; Hegde, Gayatri; Khanam, Fatema; Thirthalli, Jagadisha; Chaturvedi, Santosh K

2016-01-01

Deficits in social skills may present in a range of psychiatric disorders, particularly in the more serious and persistent conditions, and have an influence on functioning across various domains. This pilot study aimed at developing a brief measure, for structured evaluation and screening for social skills deficits, which can be easily integrated into routine clinical practice. The sample consisted of 380 inpatients and their accompanying caregivers, referred to Psychiatric Rehabilitation Services at a tertiary care government psychiatric hospital. The evaluation included an Inpatient intake Proforma and the 20-item Social Skills Assessment Screening Scale (SSASS). Disability was assessed using the Indian Disability Evaluation and Assessment Scale (IDEAS) for a subset of 94 inpatients. The analysis included means and standard deviations, frequency and percentages, Cronbach's alpha to assess internal consistency, t -tests to assess differences in social skills deficits between select subgroups, and correlation between SSASS and IDEAS scores. The results indicated the profile of social skills deficits assessed among the inpatients with varied psychiatric diagnoses. The "psychosis" group exhibited significantly higher deficits than the "mood disorder" group. Results indicated high internal consistency of the SSASS and adequate criterion validity demonstrated by correlations with select IDEAS domains. Modifications were made to the SSASS following the pilot study. The SSASS has potential value as a measure for screening and individualised intervention plans for social skills training in mental health and rehabilitation settings. The implications for future work on the psychometric properties and clinical applications are discussed.

An automated laboratory-scale methodology for the generation of sheared mammalian cell culture samples.

PubMed

Joseph, Adrian; Goldrick, Stephen; Mollet, Michael; Turner, Richard; Bender, Jean; Gruber, David; Farid, Suzanne S; Titchener-Hooker, Nigel

2017-05-01

Continuous disk-stack centrifugation is typically used for the removal of cells and cellular debris from mammalian cell culture broths at manufacturing-scale. The use of scale-down methods to characterise disk-stack centrifugation performance enables substantial reductions in material requirements and allows a much wider design space to be tested than is currently possible at pilot-scale. The process of scaling down centrifugation has historically been challenging due to the difficulties in mimicking the Energy Dissipation Rates (EDRs) in typical machines. This paper describes an alternative and easy-to-assemble automated capillary-based methodology to generate levels of EDRs consistent with those found in a continuous disk-stack centrifuge. Variations in EDR were achieved through changes in capillary internal diameter and the flow rate of operation through the capillary. The EDRs found to match the levels of shear in the feed zone of a pilot-scale centrifuge using the experimental method developed in this paper (2.4×10 5 W/Kg) are consistent with those obtained through previously published computational fluid dynamic (CFD) studies (2.0×10 5 W/Kg). Furthermore, this methodology can be incorporated into existing scale-down methods to model the process performance of continuous disk-stack centrifuges. This was demonstrated through the characterisation of culture hold time, culture temperature and EDRs on centrate quality. © 2017 The Authors. Biotechnology Journal published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Manufacturing demonstration of microbially mediated zinc sulfide nanoparticles in pilot-plant scale reactors.

PubMed

Moon, Ji-Won; Phelps, Tommy J; Fitzgerald, Curtis L; Lind, Randall F; Elkins, James G; Jang, Gyoung Gug; Joshi, Pooran C; Kidder, Michelle; Armstrong, Beth L; Watkins, Thomas R; Ivanov, Ilia N; Graham, David E

2016-09-01

The thermophilic anaerobic metal-reducing bacterium Thermoanaerobacter sp. X513 efficiently produces zinc sulfide (ZnS) nanoparticles (NPs) in laboratory-scale (≤ 24-L) reactors. To determine whether this process can be up-scaled and adapted for pilot-plant production while maintaining NP yield and quality, a series of pilot-plant scale experiments were performed using 100-L and 900-L reactors. Pasteurization and N2-sparging replaced autoclaving and boiling for deoxygenating media in the transition from small-scale to pilot plant reactors. Consecutive 100-L batches using new or recycled media produced ZnS NPs with highly reproducible ~2-nm average crystallite size (ACS) and yields of ~0.5 g L(-1), similar to the small-scale batches. The 900-L pilot plant reactor produced ~320 g ZnS without process optimization or replacement of used medium; this quantity would be sufficient to form a ZnS thin film with ~120 nm thickness over 0.5 m width × 13 km length. At all scales, the bacteria produced significant amounts of acetic, lactic, and formic acids, which could be neutralized by the controlled addition of sodium hydroxide without the use of an organic pH buffer, eliminating 98 % of the buffer chemical costs. The final NP products were characterized using XRD, ICP-OES, TEM, FTIR, PL, DLS, HPLC, and C/N analyses, which confirmed that the growth medium without organic buffer enhanced the ZnS NP properties by reducing carbon and nitrogen surface coatings and supporting better dispersivity with similar ACS.

Pilot-scale evaluation of a novel TiO2-supported V2O5 catalyst for DeNOx at low temperatures at a waste incinerator.

PubMed

Jung, Hyounduk; Park, Eunseuk; Kim, Minsu; Jurng, Jongsoo

2017-03-01

The removal of NOx by catalytic technology at low temperatures is significant for treatment of flue gas in waste incineration plants, especially at temperatures below 200°C. A novel highly active TiO 2 -supported vanadium oxide catalyst at low temperatures (200-250°C) has been developed for the selective catalytic reduction (SCR) de-NOx process with ammonia. The catalyst was evaluated in a pilot-scale equipment, and the results were compared with those obtained in our previous work using laboratory scale (small volume test) equipment as well as bench-scale laboratory equipment. In the present work, we have performed our experiments in pilot scale equipment using a part of effluent flue gas that was obtained from flue gas cleaning equipment in a full-scale waste incineration plant in South Korea. Based on our previous work, we have prepared a TiO 2 -supported V 2 O 5 catalyst coated (with a loading of 7wt% of impregnated V 2 O 5 ) on a honeycomb cordierite monolith to remove NOx from a waste incinerator flue gas at low temperatures. The NOx (nitrogen oxides) removal efficiency of the SCR catalyst bed was measured in a catalyst fixed-bed reactor (flow rate: 100m 3 h -1 ) using real exhaust gas from the waste incinerator. The experimental results showed that the V 2 O 5 /TiO 2 SCR catalyst exhibited good DeNOx performance (over 98% conversion at an operating temperature of 300°C, 95% at 250°C, and 70% at 200°C), and was much better than the performance of commercial SCR catalysts (as low as 55% conversion at 250°C) under the same operating conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Nonlinear Dynamic Inversion Baseline Control Law: Flight-Test Results for the Full-scale Advanced Systems Testbed F/A-18 Airplane

NASA Technical Reports Server (NTRS)

Miller, Christopher J.

2011-01-01

A model reference nonlinear dynamic inversion control law has been developed to provide a baseline controller for research into simple adaptive elements for advanced flight control laws. This controller has been implemented and tested in a hardware-in-the-loop simulation and in flight. The flight results agree well with the simulation predictions and show good handling qualities throughout the tested flight envelope with some noteworthy deficiencies highlighted both by handling qualities metrics and pilot comments. Many design choices and implementation details reflect the requirements placed on the system by the nonlinear flight environment and the desire to keep the system as simple as possible to easily allow the addition of the adaptive elements. The flight-test results and how they compare to the simulation predictions are discussed, along with a discussion about how each element affected pilot opinions. Additionally, aspects of the design that performed better than expected are presented, as well as some simple improvements that will be suggested for follow-on work.

Can teamwork and situational awareness (SA) in ED resuscitations be improved with a technological cognitive aid? Design and a pilot study of a team situation display.

PubMed

Parush, A; Mastoras, G; Bhandari, A; Momtahan, K; Day, K; Weitzman, B; Sohmer, B; Cwinn, A; Hamstra, S J; Calder, L

2017-12-01

Effective teamwork in ED resuscitations, including information sharing and situational awareness, could be degraded. Technological cognitive aids can facilitate effective teamwork. This study focused on the design of an ED situation display and pilot test its influence on teamwork and situational awareness during simulated resuscitation scenarios. The display design consisted of a central area showing the critical dynamic parameters of the interventions with an events time-line below it. Static information was placed at the sides of the display. We pilot tested whether the situation display could lead to higher scores on the Clinical Teamwork Scale (CTS), improved scores on a context-specific Situational Awareness Global Assessment Technique (SAGAT) tool, and team communication patterns that reflect teamwork and situational awareness. Resuscitation teamwork, as measured by the CTS, was overall better with the presence of the situation display as compared with no situation display. Team members discussed interventions more with the situation display compared with not having the situation display. Situational awareness was better with the situation display only in the trauma scenario. The situation display could be more effective for certain ED team members and in certain cases. Overall, this pilot study implies that a situation display could facilitate better teamwork and team communication in the resuscitation event. Copyright © 2017 Elsevier Inc. All rights reserved.

Quantification of a maximum injection volume of CO2 to avert geomechanical perturbations using a compositional fluid flow reservoir simulator

NASA Astrophysics Data System (ADS)

Jung, Hojung; Singh, Gurpreet; Espinoza, D. Nicolas; Wheeler, Mary F.

2018-02-01

Subsurface CO2 injection and storage alters formation pressure. Changes of pore pressure may result in fault reactivation and hydraulic fracturing if the pressure exceeds the corresponding thresholds. Most simulation models predict such thresholds utilizing relatively homogeneous reservoir rock models and do not account for CO2 dissolution in the brine phase to calculate pore pressure evolution. This study presents an estimation of reservoir capacity in terms of allowable injection volume and rate utilizing the Frio CO2 injection site in the coast of the Gulf of Mexico as a case study. The work includes laboratory core testing, well-logging data analyses, and reservoir numerical simulation. We built a fine-scale reservoir model of the Frio pilot test in our in-house reservoir simulator IPARS (Integrated Parallel Accurate Reservoir Simulator). We first performed history matching of the pressure transient data of the Frio pilot test, and then used this history-matched reservoir model to investigate the effect of the CO2 dissolution into brine and predict the implications of larger CO2 injection volumes. Our simulation results -including CO2 dissolution- exhibited 33% lower pressure build-up relative to the simulation excluding dissolution. Capillary heterogeneity helps spread the CO2 plume and facilitate early breakthrough. Formation expansivity helps alleviate pore pressure build-up. Simulation results suggest that the injection schedule adopted during the actual pilot test very likely did not affect the mechanical integrity of the storage complex. Fault reactivation requires injection volumes of at least about sixty times larger than the actual injected volume at the same injection rate. Hydraulic fracturing necessitates much larger injection rates than the ones used in the Frio pilot test. Tested rock samples exhibit ductile deformation at in-situ effective stresses. Hence, we do not expect an increase of fault permeability in the Frio sand even in the presence of fault reactivation.

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Global Research has developed an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GE Global Research (prime contractor) wasmore » awarded a contract from U.S. DOE NETL to develop the UFP technology. Work on this Phase I program started on October 1, 2000. The project team includes GE Global Research, Southern Illinois University at Carbondale (SIU-C), California Energy Commission (CEC), and T. R. Miles, Technical Consultants, Inc. In the UFP technology, coal and air are simultaneously converted into separate streams of (1) high-purity hydrogen that can be utilized in fuel cells or turbines, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure vitiated air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on ASPEN Plus process modeling, has an estimated process efficiency of 6% higher than IGCC with conventional CO{sub 2} separation. The current R&D program will determine the feasibility of the integrated UFP technology through pilot-scale testing, and will investigate operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates experimental testing, modeling and economic studies to demonstrate the UFP technology. This is the thirteenth quarterly technical progress report for the UFP program, which is supported by U.S. DOE NETL under Contract No. DE-FC26-00FT40974. This report summarizes program accomplishments for the period starting October 1, 2003 and ending December 31, 2003. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab-scale experimental testing, pilot-scale assembly, pilot-scale demonstration and program management and technology transfer.« less

The role of empathy in responses to persuasive risk communication: overcoming resistance to HIV prevention messages.

PubMed

Campbell, Rose G; Babrow, Austin S

2004-01-01

This article offers a theoretical analysis of the role of empathy as a key mediator of the suasive effects of health messages, and it discusses the testing of an empirical tool for studying the state of empathy in responses to persuasive messages. It is argued that felt empathy evokes cognitive and emotional processing conducive to important health-promoting responses. This assertion was tested by operationalizing empathy as a response state via a new measure, the Empathy Response Scale (ERS). Two pilot tests and one major study, all set in the challenging area of HIV/AIDS prevention, provided preliminary data supporting the theoretical analysis and the ERS as a measure of the state of empathy. The article concludes with discussions of directions for future tests of the empathy theory and scale, as well as applications of the current framework for developing persuasive messages.

ClearFuels-Rentech Integrated Biorefinery Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pearson, Joshua

The project Final Report describes the validation of the performance of the integration of two technologies that were proven individually on a pilot scale and were demonstrated as a pilot scale integrated biorefinery. The integrated technologies were a larger scale ClearFuels’ (CF) advanced flexible biomass to syngas thermochemical high efficiency hydrothermal reformer (HEHTR) technology with Rentech’s (RTK) existing synthetic gas to liquids (GTL) technology.

PILOT-SCALE EVALUATION OF NEW RESIN APPLICATION EQUIPMENT FOR FIBER- REINFORCED PLASTICS

EPA Science Inventory

The article gives results of a pilot-scale evaluation of new resin application equipment for fiber- reinforced plastics. The study, an evaluation and comparison of styrene emissions, utilized Magnum's FIT(TM) nozzle with conventional spray guns and flow coaters (operated at both ...

REMOVAL OF PCBS FROM A CONTAMINATED SOIL USING CF-SYSTEMS SOLVENT EXTRACTION PROCESS

EPA Science Inventory

The US EPA's START team in cooperation with EPA's SITE program evaluated a pilot scale solvent extraction process developed by CF-Systems. This process uses liquified propane to extract organic contaminants from soils, sludges, and sediments. A pilot-scale evaluation was conducte...

FATE OF SEX HORMONES IN TWO PILOT-SCALE MUNICIPAL WASTEWATER TREATMENT PLANTS: CONVENTIONAL TREATMENT

EPA Science Inventory

The fate of seven sex hormones (estrone (E1), estradiol (E2), estriol (E3), ethinylestradiol (EE2), testosterone, androstenedione, and progesterone) was determined in two pilot-scale wastewater treatment plants operated under conventional loading conditions. The levels of hormon...

A pilot study of research utilization practices and critical thinking dispositions of Alberta dental hygienists.

PubMed

Cobban, S J; Profetto-McGrath, J

2008-08-01

In order to test interventions for increasing uptake of research findings into dental hygiene practice, we must first identify factors that influence research use. There has been little work on this topic in dental hygiene, but much in other disciplines that can provide exemplars of how others have approached the study of this phenomenon. A pilot study was conducted to determine if protocols used to study research utilization (RU) behaviours and critical thinking dispositions (CTD) in nursing could also be applied to dental hygiene. A cross-sectional survey design was used with a random sample of 640 practicing dental hygienists in Alberta, Canada. Three questionnaires were included: one to capture measures of RU including direct, indirect and symbolic RU; the California Critical Thinking Dispositions Inventory (CCTDI) and a demographics questionnaire. Mean responses for the three types of RU were highest for indirect at 3.52 (SD 0.720), followed by direct at 3.13 (SD 0.903) and symbolic 2.86 (SD 0.959). The majority (74.8%) scored between 280 and 350 on the CCTDI (maximum 420). Cronbach's alpha reliability for the RU measures and four of the seven sub-scales were over .7, indicating internal consistency reliability. The instruments proved reliable for this population, but other challenges, including a low response rate, were identified during the process of using the RU questionnaire in the context of dental hygiene practice. Pilot testing identified the need for improvements to the presentation of scales to reduce cognitive load and improve the response rate.

Model-based Extracted Water Desalination System for Carbon Sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gettings, Rachel; Dees, Elizabeth

The focus of this research effort centered around water recovery from high Total Dissolved Solids (TDS) extracted waters (180,000 mg/L) using a combination of water recovery (partial desalination) technologies. The research goals of this project were as follows: 1. Define the scope and test location for pilot-scale implementation of the desalination system, 2.Define a scalable, multi-stage extracted water desalination system that yields clean water, concentrated brine, and, salt from saline brines, and 3. Validate overall system performance with field-sourced water using GE pre-pilot lab facilities. Conventional falling film-mechanical vapor recompression (FF-MVR) technology was established as a baseline desalination process. Amore » quality function deployment (QFD) method was used to compare alternate high TDS desalination technologies to the base case FF-MVR technology, including but not limited to: membrane distillation (MD), forward osmosis (FO), and high pressure reverse osmosis (HPRO). Technoeconomic analysis of high pressure reverse osmosis (HPRO) was performed comparing the following two cases: 1. a hybrid seawater RO (SWRO) plus HPRO system and 2. 2x standard seawater RO system, to achieve the same total pure water recovery rate. Pre-pilot-scale tests were conducted using field production water to validate key process steps for extracted water pretreatment. Approximately 5,000 gallons of field produced water was processed through, microfiltration, ultrafiltration, and steam regenerable sorbent operations. Improvements in membrane materials of construction were considered as necessary next steps to achieving further improvement in element performance at high pressure. Several modifications showed promising results in their ability to withstand close to 5,000 PSI without gross failure.« less

Development and evaluation of a dietary self-management programme for older adults with low literacy and heart disease: pilot study of feasibility and acceptability.

PubMed

Shao, Jung-Hua; Chen, Su-Hui

2016-12-01

To develop a dietary self-management programme for salt-, fluid-, fat- and cholesterol-intake behaviours for older adults with low literacy and heart disease and evaluate the feasibility and acceptability of the programme. Eating behaviours such as fluid, salt, fat and cholesterol intake are an important factor related to heart disease outcomes. People with low literacy have difficulty following recommended health behaviours, but limited research has investigated intervention programmes for this population. Programme development and pilot testing its feasibility and acceptability. Recommendations were also collected from participants and the research assistant for future large-scale interventions. The study had two phases. Phase I consisted of programme development based on previous qualitative findings, a systematic review of the literature, clinical practice experience and expert opinion. In Phase II, we pilot tested the programme from January - June 2014 in a convenience sample of 10 older adults with low literacy, heart disease and recruited from a medical centre in northern Taiwan. Pilot testing showed that our programme was feasible and acceptable to older adults with low literacy and heart disease. Moreover, the final version of the programme was revised based on participants' and the research assistant's recommendations. Our study results suggest that with guidance and assistance, older adults with low literacy and heart disease can be motivated to take action for their health and are empowered by learning how to self-manage their heart-healthy eating behaviours. © 2016 John Wiley & Sons Ltd.

Cross-cultural validation of instruments measuring health beliefs about colorectal cancer screening among Korean Americans.

PubMed

Lee, Shin-Young; Lee, Eunice E

2015-02-01

The purpose of this study was to report the instrument modification and validation processes to make existing health belief model scales culturally appropriate for Korean Americans (KAs) regarding colorectal cancer (CRC) screening utilization. Instrument translation, individual interviews using cognitive interviewing, and expert reviews were conducted during the instrument modification phase, and a pilot test and a cross-sectional survey were conducted during the instrument validation phase. Data analyses of the cross-sectional survey included internal consistency and construct validity using exploratory and confirmatory factor analysis. The main issues identified during the instrument modification phase were (a) cultural and linguistic translation issues and (b) newly developed items reflecting Korean cultural barriers. Cross-sectional survey analyses during the instrument validation phase revealed that all scales demonstrate good internal consistency reliability (Cronbach's alpha=.72~.88). Exploratory factor analysis showed that susceptibility and severity loaded on the same factor, which may indicate a threat variable. Items with low factor loadings in the confirmatory factor analysis may relate to (a) lack of knowledge about fecal occult blood testing and (b) multiple dimensions of the subscales. Methodological, sequential processes of instrument modification and validation, including translation, individual interviews, expert reviews, pilot testing and a cross-sectional survey, were provided in this study. The findings indicate that existing instruments need to be examined for CRC screening research involving KAs.

Development and psychometric pilot-testing of a questionnaire for the evaluation of satisfaction with continuing education in infection control nurses.

PubMed

Meng, Michael; Peter, Daniel; Mattner, Frauke; Igel, Christoph; Kugler, Christiane

2018-05-16

Satisfaction with continuing education can be defined as positive attitudes towards educational programs, which has potential to strengthen learning outcomes. A multi-dimensional construct may enhance continuing education program evaluation processes. The objective is to describe the development and psychometric testing of the 'affective - behavioral - cognitive - satisfaction questionnaire' (ABC-SAT) for assessing participants' satisfaction with a continuing education program for nurses in infection control. The multi-staged development of a satisfaction questionnaire comprised of three subscales. The pilot tool was administered to a nationwide sample of 126 infection control nurses to assess satisfaction after participating in a continuing education program. Satisfaction scores were calculated and psychometric testing was performed to determine reliability, using Cronbach's alpha, face validity, objectivity, and economy. A principle component analysis using varimax rotation and Kaiser normalization was performed. The analysis led to a three-factor solution of the questionnaire with 11 items, explaining 61.4% of the variance. Internal consistency of three scales using Cronbach's alpha was 0.83, 0.60, and 0.66, respectively. Selectivity coefficients varied between 0.39 and 0.70. Participants needed approximately three minutes to complete the questionnaire. Initial findings refer to a satisfying scale structure and internal consistency of the 3-dimensional ABC-SAT questionnaire. Further research is required to confirm the questionnaires' psychometric properties. Copyright © 2018 Elsevier Ltd. All rights reserved.

National standards for the long-term care ombudsman program and a tool to assess compliance: the Huber Badrak Borders Scales.

PubMed

Huber, R; Borders, K W; Badrak, K; Netting, F E; Nelson, H W

2001-04-01

We propose national standards previously recommended for the Long-Term Care Ombudsman Program by an Institute of Medicine program evaluation committee, and introduce a tool to measure the compliance of local ombudsman programs to those standards: the Huber Badrak Borders Scales. The best practices for ombudsman programs detailed in the committee's report were adapted to 43 Likert-type scales that were then averaged into 10 infrastructure component scales: (a) program structure, (b) qualifications of local ombudsmen, (c) legal authority, (d) financial resources, (e) management information systems, (f) legal resources, (g) human resources, (h) resident advocacy services, (i) systemic advocacy, and (j) educational services. The scales were pilot-tested in 1996 and 1999 with Kentucky ombudsmen. The means of 9 of these 10 scales were higher in 1999 than in 1996, suggesting that local ombudsman programs were more in compliance with the proposed standards in 1999 than three years earlier. The development process consisted of 10 adopt-test-revise-retest steps that can be replicated by other types of programs to develop program compliance tools.

Testing the robustness of Citizen Science projects: Evaluating the results of pilot project COMBER

PubMed Central

Faulwetter, Sarah; Dailianis, Thanos; Smith, Vincent Stuart; Koulouri, Panagiota; Dounas, Costas; Arvanitidis, Christos

2016-01-01

Abstract Background Citizen Science (CS) as a term implies a great deal of approaches and scopes involving many different fields of science. The number of the relevant projects globally has been increased significantly in the recent years. Large scale ecological questions can be answered only through extended observation networks and CS projects can support this effort. Although the need of such projects is apparent, an important part of scientific community cast doubt on the reliability of CS data sets. New information The pilot CS project COMBER has been created in order to provide evidence to answer the aforementioned question in the coastal marine biodiversity monitoring. The results of the current analysis show that a carefully designed CS project with clear hypotheses, wide participation and data sets validation, can be a valuable tool for the large scale and long term changes in marine biodiversity pattern change and therefore for relevant management and conservation issues. PMID:28174507