DEVICE FOR CONTROLLING INSERTION OF ROD

DOEpatents

Beaty, B.J.

1958-10-14

A device for rapidly inserting a safety rod into a nuclear reactor upon a given signal or in the event of a power failure in order to prevent the possibility of extensive damage caused by a power excursion is described. A piston is slidably mounted within a vertical cylinder with provision for an electromagnetic latch at the top of the cylinder. This assembly, with a safety rod attached to the piston, is mounted over an access port to the core region of the reactor. The piston is normally latched at the top of the cylinder with the safety rod clear of the core area, however, when the latch is released, the piston and rod drop by their own weight to insert the rod. Vents along the side of the cylinder permit the escape of the air entrapped under the piston over the greater part of the distance, however, at the end of the fall the entrapped air is compressed thereby bringing the safety rod gently to rest, thus providing for a rapid automatic insertion of the rod with a minimum of structural shock.

An innovative piston corer for large‐volume sediment samples

PubMed Central

Haselmair, Alexandra; Stachowitsch, Michael; Zuschin, Martin

2016-01-01

Abstract Coring is one of several standard procedures to extract sediments and their faunas from open marine, estuarine, and limnic environments. Achieving sufficiently deep penetration, obtaining large sediment volumes in single deployments, and avoiding sediment loss upon retrieval remain problematic. We developed a piston corer with a diameter of 16 cm that enables penetration down to 1.5 m in a broad range of soft bottom types, yields sufficient material for multiple analyses, and prevents sediment loss due to a specially designed hydraulic core catcher. A novel extrusion system enables very precise slicing and preserves the original sediment stratification by keeping the liners upright. The corer has moderate purchase costs and a robust and simple design that allows for a deployment from relatively small vessels as available at most marine science institutions. It can easily be operated by two to three researchers rather than by specially trained technicians. In the northern Adriatic Sea, the corer successfully extracted more than 50 cores from a range of fine mud to coarse sand, at water depths from three to 45 m. The initial evaluation of the cores demonstrated their usefulness for fauna sequences along with heavy metal, nutrient and pollutant analyses. Their length is particularly suited for historical ecological work requiring sedimentary and faunal sequences to reconstruct benthic communities over the last millennia. PMID:28111529

Accretion rate of extraterrestrial matter: Iridium deposited over the last 70 million years

NASA Technical Reports Server (NTRS)

Kyte, Frank T.

1988-01-01

In order to quantify the accretion rate of extraterrestrial matter during the Cenozoic, Ir concentrations were measured in a continuous series of 450 samples across most of the length of piston core LL44-GPC3. LL44-GPC3 is a 25-meter-long, large-diameter piston core of abyssal clay from the central North Pacific. This core contains a nearly continuous record of sedimentation over the last 70 Ma, as this site migrated from a region near the Equator in the late Cretaceous to its present position north of Hawaii. The first-cut survey across the core is nearing completion, and all of the conclusions of the earlier study, in which was reported the concentrations of Ir, Co, and Sb across 9 meters of this core, remain unchanged. The only strongly enhanced Ir concentrations occur at the Cretaceous-Tertiary (K-T) boundary and outside the K-T boundary Ir correlates well with Co, a terrestrial element which is largely present in hydrogenous ferromanganese oxide precipitates from seawater. Concentrations of both elements appear to be inversely correlated with the sedimentation rate. Although the K-T Ir anomaly is unique in magnitude in this core, there are several small bumps in the Ir profile which may reflect smaller accretionary events. The most promising Ir enhancement was observed in a 30 cm section approximately 1 m below the K-T boundary. Preliminary data suggest deposition of an excess across this interval at a time estimate to be approximate 1 Ma before the K-T impact event, but there is insufficient evidence at present to prove that this reflects enhanced accretion of extraterrestrial matter. A detailed model is being prepared of the chemical record of sedimentation in this core using a combined database of 39 elements in approximately 450 samples across the Cenozoic. Preliminary working model indicates that the only sedimentary sources which contribute significantly to the Ir budget in this core are the hydrogenous precipitates and extraterrestrial particulates.

Paleoseismic events inferred from marine seismogenic turbidites of the eastern Nankai Trough

NASA Astrophysics Data System (ADS)

Okutsu, N.; Ashi, J.; Omura, A.; Yamaguchi, A.; Suganuma, Y.; Kanamatsu, T.; Murayama, M.

2016-12-01

Paleoseismology using marine seismogenic turbidites is a developing field especially in subduction margins. However, very fine-grained turbidites are difficult to distinguish from hemipelagic mud. The primary focus of this study is to understand the characteristics of the muddy turbidites. The second focus is to discuss the muddy turbidites distributions and their ages from a longer sediment core, and understand the paleoseismic records of eastern Nankai Trough, Japan. The samples used in this study include multiple cores and a piston core which were collected from the sedimentary basin southwest off Kii Peninsula during the R/V Shinsei Maru KS-14-8 cruise. The sampling site is located at the ENE-WSW elongated basin between the accretionary prism and the forearc basin off Kumano without terrestrial sediment supply. The basin exhibits a terminal basin that captures all sediments supplied from outside. From the multiple core samples, the Cs-137 and Pb- 210 concentration distribution indicates that the muddy sediment layer in the upper 17 cm was formed from the 2004 off the Kii Peninsula earthquake. Visual observation and X-ray CT scans were conducted alongside other measurements for anisotropy of magnetic susceptibility (AMS), paleomagnetism, rock magnetism, electrical resistivity, and X-ray fluorescence core scanning (XRF). Muddy seismogenic turbidites associated with the 2004 off the Kii Peninsula earthquake have thick homogeneous clay layer above the silty lamination. The magnetic susceptibility decreases upwards in the lamination. This specific feature is thought to have formed as the muddy turbiditity current slowly decelerated and slowly settled down the slope. From the results of XRF core scanning, Ca and Fe have a peak at basement of turbidites, and decrease upwards. Ca is thought to correspond to amount of the foraminiferas. In piston core, we observed the same sedimentary and magnetic characteristics as the multiple cores. Based on stratigraphic information from volcanic ash and radiocarbon age of the foraminifera, intercalation pattern of muddy turbidite layers almost consistent with the known past earthquake recurrence times in the Nankai subduction margin. Reversed age recognized beneath the thick turbidite layer suggests reworking of landslide deposits probably due to the strong shaking.

Oscillatory erosion and transport flume with superimposed unidirectional flow

DOEpatents

Jepsen, Richard A.; Roberts, Jesse D.

2004-01-20

A method and apparatus for measuring erosion rates of sediments and at high shear stresses due to complex wave action with, or without, a superimposed unidirectional current. Water is forced in a channel past an exposed sediment core sample, which erodes sediments when a critical shear stress has been exceeded. The height of the core sample is adjusted during testing so that the sediment surface remains level with the bottom of the channel as the sediments erode. Complex wave action is simulated by driving tandom piston/cylinder mechanisms with computer-controlled stepper motors. Unidirectional flow, forced by a head difference between two open tanks attached to each end of the channel, may be superimposed on to the complex wave action. Sediment traps may be used to collect bedload sediments. The total erosion rate equals the change in height of the sediment core sample divided by a fixed period of time.

Radiocarbon ages and age models for the past 30,000 years in Bear Lake, Utah and Idaho

USGS Publications Warehouse

Colman, Steven M.; Rosenbaum, J.G.; Kaufman, D.S.; Dean, W.E.; McGeehin, J.P.

2009-01-01

Radiocarbon analyses of pollen, ostracodes, and total organic carbon (TOC) provide a reliable chronology for the sediments deposited in Bear Lake over the past 30,000 years. The differences in apparent age between TOC, pollen, and carbonate fractions are consistent and in accord with the origins of these fractions. Comparisons among different fractions indicate that pollen sample ages are the most reliable, at least for the past 15,000 years. The post-glacial radiocarbon data also agree with ages independently estimated from aspartic acid racemization in ostracodes. Ages in the red, siliclastic unit, inferred to be of last glacial age, appear to be several thousand years too old, probably because of a high proportion of reworked, refractory organic carbon in the pollen samples. Age-depth models for five piston cores and the Bear Lake drill core (BL00-1) were constructed by using two methods: quadratic equations and smooth cubic-splinefits. The two types of age models differ only in detail for individual cores, and each approach has its own advantages. Specific lithological horizons were dated in several cores and correlated among them, producing robust average ages for these horizons. The age of the correlated horizons in the red, siliclastic unit can be estimated from the age model for BL00-1, which is controlled by ages above and below the red, siliclastic unit. These ages were then transferred to the correlative horizons in the shorter piston cores, providing control for the sections of the age models in those cores in the red, siliclastic unit. These age models are the backbone for reconstructions of past environmental conditions in Bear Lake. In general, sedimentation rates in Bear Lake have been quite uniform, mostly between 0.3 and 0.8 mm yr-1 in the Holocene, and close to 0.5 mm yr-1 for the longer sedimentary record in the drill core from the deepest part of the lake. Copyright ?? 2009 The Geological Society of America.

Introduction to paleoenvironments of Bear Lake, Utah and Idaho, and its catchment

USGS Publications Warehouse

Rosenbaum, Joseph G.; Kaufman, Darrell S.

2009-01-01

In 1996 a group led by the late Kerry Kelts (University of Minnesota) and Robert Thompson (U.S. Geological Survey) acquired three piston cores (BL96-1, -2, and -3) from Bear Lake. The coring arose from their recognition of Bear Lake as a potential repository of long records of paleoenvironmental change. They recognized that the lake is located in an area that is sensitive to changes in regional climate patterns (Dean et al., this volume), that the lake basin is long lived (see Colman, 2006; Kaufman et al., this volume), and that, unlike many lakes in the Great Basin, Bear Lake was never dry during warm dry periods. Bear Lake lies in the northeastern Great Basin to the northeast of Great Salt Lake, just south of the Snake River drainage, and a short distance west of the Green River drainage that makes up part of the Upper Colorado River Basin (Fig. 1). Similarity among the historic Bear Lake and Great Salt Lake hydrographs and flows on the Green River indicates that the hydrology of Bear Lake reflects regional precipitation (Fig. 2). Therefore, paleorecords from Bear Lake are important to understanding past climate for a large region, including the Upper Colorado River Basin, the source of much of the water for the southwestern United States. Initially, paleoenvironmental studies of Bear Lake sediments focused on cores BL96-1, -2, and -3. Additional coring was conducted to elucidate the spatial distribution of sedimentary units and to extend the record back in time. The study was also expanded to include extensive study of the catchment, including the properties of catchment materials and the processes that could potentially affect the delivery of catchment materials to the lake. Cores BL96-1, -2, and -3 were taken with a Kullenburg piston corer along an east–west profile in roughly 50, 40, and 30 m of water, respectively (Table 1, Fig. 3). These three cores, each taken as a single 4- to 5-m-long segment, provide a nearly complete composite section from ca. 26 cal ka to the late Holocene. In 1998 a number of short gravity cores were taken from the uppermost water-rich sediments that were not sampled by the 1996 cores. During 2000, cores were taken with a percussion piston corer (manufactured by UWITEC) at three locations in and around Mud Lake and at two locations in the northern end of Bear Lake (Fig. 3). Cores acquired with the percussion corer comprise as many as three overlapping segments up to 2 m in length. In 2002, additional percussion piston cores and associated gravity cores of the uppermost sediments were acquired from five sites in the northern half of the lake. In conjunction with two of the cores collected in 2000, these cores form a north–south profile along a seismic line and span water depths from less than 10 m to ~40 m. Data from this profile provide much of the evidence for lake-level variations (Smoot and Rosenbaum, this volume). Finally, during 2000, two long cores, BL00-1D and -1E (collectively referred to here simply as BL00-1), were taken at a site near the depocenter during testing of the GLAD800 coring platform (Fig. 4; Dean et al., 2002). These cores provide a record back to ca. 220 ka.

Are Eastern Basin (Ross Sea, Antarctica) Bathymetric Ridges Associated With the Last Glacial Maximum?

NASA Astrophysics Data System (ADS)

Chow, J. M.; Bart, P. J.

2005-05-01

Ross Sea (Antarctica) Eastern Basin bathymetric ridges have been interpreted to be ice stream divides created during the Last Glacial Maximum (LGM) advance of the Antarctic Ice Sheet based on radiocarbon dating of organic matter from near-seafloor sediments recovered in piston cores (Domack et al., 1999). Detailed seismic correlations and contour mapping show that there are at least five thick units outcropping in Eastern Basin. Four of these seismically-defined units can be correlated to age control at DSDP sites 270 and 272. In contrast to the near-seafloor sampling, the interiors of these units were initially assigned a Pliocene age based on a variety of microfossil biozones (Hayes and Frakes, 1975). Savage and Ciesielski (1983) determined that the youngest unit was deposited during the Coscinodiscus lentiginosus (since renamed Thalassiosira lentiginosa) diatom biozone (i.e., the unit formed sometime between 0.65 Ma to Recent timeframe). Thus, seafloor units in the area probably are of Quaternary age, but not necessarily LGM age. More recently, diatom biozonations for the Southern Ocean have been revised to provide more detailed biochronostratigraphic resolution (Zielinski and Gersonde, 2002; Zielinski et al., 2002). We are using the most recently-revised Southern Ocean diatom-zonation schemes to systematically evaluate ages of samples taken from the base of piston cores penetrating the five individual seismically-defined units in Eastern Basin. Using this sampling strategy, we increase the chances of penetrating through the Recent hemipelagic drape to sample the underlying seismically-defined units.

Late Quaternary sediment-accumulation rates within the inner basins of the California Continental Borderland in support of geologic hazard evaluation

USGS Publications Warehouse

Normark, W.R.; McGann, M.; Sliter, R.W.

2009-01-01

An evaluation of the geologic hazards of the inner California Borderland requires determination of the timing for faulting and mass-movement episodes during the Holocene. Our effort focused on basin slopes and turbidite systems on the basin floors for the area between Santa Barbara and San Diego, California. Dating condensed sections on slopes adjacent to fault zones provides better control on fault history where high-resolution, seismic-reflection data can be used to correlate sediment between the core site and the fault zones. This study reports and interprets 147 radiocarbon dates from 43 U.S. Geological Survey piston cores as well as 11 dates from Ocean Drilling Program Site 1015 on the floor of Santa Monica Basin. One hundred nineteen dates from 39 of the piston cores have not previously been published. Core locations were selected for hazard evaluation, but despite the nonuniform distribution of sample locations, the dates obtained for the late Quaternary deposits are useful for documenting changes in sediment-accumulation rates during the past 30 ka. Cores from basins receiving substantial sediment from rivers, i.e., Santa Monica Basin and the Gulf of Santa Catalina, show a decrease in sediment supply during the middle Holocene, but during the late Holocene after sea level had reached the current highstand condition, rates then increased partly in response to an increase in El Ni??o-Southern Oscillation events during the past 3.5 ka. ?? 2009 The Geological Society of America.

Technologies for Assessing the Geologic and Geomorphic History of Coasts

DTIC Science & Technology

1993-03-01

memory have dramatically increased the storage capacity of underwater instruments. Some can remain onsite as long as 12 months. 2. If a gage floods, data...analyzing stratigraphic data, the age relations of the rock strata, rock form and distribution, lithologies, fossil record, biopaleogeography, and...coring tube barrel 10 ft; UD samples. gravity corer) contains a piston that additional 10-ft remains stationary on the sections can be seafloor during

Anisotropy of magnetic susceptibility used to detect coring-induced sediment disturbance and filter palaeomagnetic secular variation data: IODP sites M0061 and M0062 (Baltic Sea)

NASA Astrophysics Data System (ADS)

Snowball, Ian; Almqvist, Bjarne; Lougheed, Bryan; Svensson, Anna; Wiers, Steffen; Herrero-Bervera, Emilio

2017-04-01

Inspired by palaeomagnetic data obtained from two sites (M0061 and M0062) cored during IODP Expedition 347 - Baltic Sea Paleoenvironment we studied the Hemsön Alloformation, which is a series of brackish water muds consisting of horizontal planar and parallel laminated (varved) silty clays free from bioturbation. We determined the anisotropy of magnetic susceptibility (AMS) and characteristic remanence (ChRM) directions of a total of 1,102 discrete samples cut from (i) IODP cores recovered by an Advanced Piston corer and (ii) a series of six sediment cores recovered from the same sites by a Kullenberg piston corer. Systematic core splitting, sub-sampling methods and measurements were applied to all sub-samples. We experimentally tested for field-impressed AMS of these muds, in which titanomagnetite carries magnetic remanence and this test was negative. The AMS is likely determined by paramagnetic minerals. As expected for horizontally bedded sediments, the vast majority of the K1 (maximum) and K2 (intermediate) axes had inclinations close to 0 degrees and the AMS shape parameter (T) indicates an oblate fabric. The declinations of the K1 and K2 directions of the sub-samples taken from Kullenberg cores showed a wide distribution around the bedding plane, with no preferred alignment along any specimen axis. Exceptions are samples from the upper 1.5 m of some of these cores, in which the K1 and K2 directions were vertical, the K3 (minimum) axis shallow and T became prolate. We conclude that the Kullenberg corer, which penetrated the top sediments with a pressure of approximately 15 bar, occasionally under-sampled during penetration and vertically stretched the top sediments. Sub-samples from the upper sections of Kullenberg cores had relatively steep ChRM inclinations and we rejected samples that had a prolate, vertically oriented AMS ellipsoid. Surprisingly, the declinations of the K1 axis of all sub-samples taken from IODP APC core sections, which were not oriented relative to each other with respect to azimuth, clustered tightly within the 90-270 degree specimen axis (K2 is within the 0-180 degree axis). This axis is the direction across each cores' split surface (i.e. perpendicular to the "push" direction of the sub-sampling boxes). The APC cores were characterized by various degrees of downwards bending of the planar varves towards the inner surface of the core liner. We conclude that the initial hydraulic pressure applied by the APC, which was consistently above 50 bar during Expedition 347, was needlessly high and created a conical sediment structure and the distinct alignment of the magnetic susceptibility axes along specimen axes. APC core sections with marked disturbances were characterized by ChRM inclinations below 65 degrees, which is a lower limit predicted by time varying geomagnetic field models for the duration of the Hemsö Alloformation (the most recent 6000 years). We rejected samples for palaeomagnetic purposes if the K1 inclination was steeper than 10 degrees. Our study highlights the added value of measuring AMS of discrete sub-samples as an independent control of the suitability of sediments as a source of palaeomagnetic data.

Cogging force investigation of a free piston permanent magnet linear generator

NASA Astrophysics Data System (ADS)

Abdalla, I. I.; Zainal, A. E. Z.; Ramlan, N. A.; Firmansyah; Aziz, A. R. A.; Heikal, M. R.

2017-10-01

Better performance and higher efficiency of the vehicles can be achieved by using free piston engine, in which the piston is connected directly to the linear generator and waiving of any mechanical means. The free piston engine has the ability to overcome or reduce many of the challenges, such as the carbon dioxide (CO2) emission and fossil fuel consumption. The cogging force produces undesired vibration and acoustic noise in the generator. However, the cogging force must be minimized as much as possible, in order to have a high performance. This paper studies the effects of ferromagnetic materials on the cogging force of the permanent magnet linear generator (PMLG) to be used in a free piston engine using nonlinear finite-element analysis (FEA) under ANSYS Maxwell. The comparisons have been established for the cogging force of the PMLG under various translator velocities and three different ferromagnetic materials for the stator core, namely, Silicon Steel laminations, Mild Steel and Somaloy. It has been shown that the PMLG with a stator core made of Somaloy has a lower cogging force among them. Furthermore, the induced voltage of the PMLG at different accelerations has been studied. It is found that the PMLG with Mild Steel and Somaloy, respectively give larger induced voltage. Moreover, as the translator speed increase the induced voltage increased.

Results of Laboratory Tests on Surficial Sediments from the Upper Continental Slope Northern Gulf of Mexico

USGS Publications Warehouse

Booth, James S.

1979-01-01

The purpose of this report is to present the results of geo­technical, textural, and chemical tests performed on samples from the upper Continental Slope, northern Gulf of Mexico.The samples were collected by a piston corer up to 12 m (40 ft.} in length with a head weight of 908 kg (one ton}. The inside diameter of the C. A. B. liner was 89 mm (3.5 inches}. Upon retrieval, the cores were cut in 1.5 m sections, examined for evidence of disturbance, then, if in acceptable condition, were sealed and placed in their in situ vertical position in a refrigerated van. Once ashore, the sections were opened, sealed with wax, recapped and stored as before.The cores were split lengthwise for analysis. One half of the core was X-rayed and the radiograph was carefully examined as a further check for disturbance. This half was then archived. The other half of the core was used for the laboratory work.

Geomagnetic field variations during the last 400 kyr in the western equatorial Pacific: Paleointensity-inclination correlation revisited

NASA Astrophysics Data System (ADS)

Yamazaki, T.; Kanamatsu, T.; Mizuno, S.; Hokanishi, N.; Gaffar, E. Z.

2008-12-01

A paleomagnetic study was conducted on four piston cores newly obtained from the West Caroline Basin in the western equatorial Pacific in order to investigate variations in paleointensity and inclination during the last 400 kyr. An inclination-intensity correlation was previously reported in this region using giant piston cores, but the quality of the paleomagnetic data of the younger end, the last ca. 300 kyr, was needed to be checked because the upper part of the giant piston cores could suffer from perturbation by oversampling. Age control is based on the oxygen-isotope ratios for one core and inter-core correlation using relative paleointensity for other cores. The mean inclinations of the four cores show negative inclination anomalies ranging from -5.2 to -11.2 degree. The western equatorial Pacific is documented as a region of a large negative inclination anomalies, and the observed values are comparable to those expected from the time-averaged field (TAF) models [Johnson and Constable, 1997; Hatakeyama and Kono, 2002]. Stacked curves of paleointensity and inclination were constructed from the four cores. It was confirmed that geomagnetic variations on the order of 10 to 100 kyrs occur in inclination as well as paleointensity. A cross-correlation analysis showed that significant in-phase correlation occurs between intensity and inclination for periods longer than about 25 kyr, and power spectra of both paleointensity and inclination variations have peaks at ~100 kyr periods. The regional paleointensity stack with higher resolution than the Sint-800 stack [Guyodo and Valet, 1999] should be useful for paleointensity-assisted chronostratigraphy.

Cooled spool piston compressor

NASA Technical Reports Server (NTRS)

Morris, Brian G. (Inventor)

1993-01-01

A hydraulically powered gas compressor receives low pressure gas and outputs a high pressure gas. The housing of the compressor defines a cylinder with a center chamber having a cross-sectional area less than the cross-sectional area of a left end chamber and a right end chamber, and a spool-type piston assembly is movable within the cylinder and includes a left end closure, a right end closure, and a center body that are in sealing engagement with the respective cylinder walls as the piston reciprocates. First and second annual compression chambers are provided between the piston enclosures and center housing portion of the compressor, thereby minimizing the spacing between the core gas and a cooled surface of the compressor. Restricted flow passageways are provided in the piston closure members and a path is provided in the central body of the piston assembly, such that hydraulic fluid flows through the piston assembly to cool the piston assembly during its operation. The compressor of the present invention may be easily adapted for a particular application, and is capable of generating high gas pressures while maintaining both the compressed gas and the compressor components within acceptable temperature limits.

Extreme pressure fluid sample transfer pump

DOEpatents

Halverson, Justin E.; Bowman, Wilfred W.

1990-01-01

A transfer pump for samples of fluids at very low or very high pressures comprising a cylinder having a piston sealed with an O-ring, the piston defining forward and back chambers, an inlet and exit port and valve arrangement for the fluid to enter and leave the forward chamber, and a port and valve arrangement in the back chamber for adjusting the pressure across the piston so that the pressure differential across the piston is essentially zero and approximately equal to the pressure of the fluid so that the O-ring seals against leakage of the fluid and the piston can be easily moved, regardless of the pressure of the fluid. The piston may be actuated by a means external to the cylinder with a piston rod extending through a hole in the cylinder sealed with a bellows attached to the piston head and the interior of the back chamber.

High temperature aqueous stress corrosion testing device

DOEpatents

Bornstein, A.N.; Indig, M.E.

1975-12-01

A description is given of a device for stressing tensile samples contained within a high temperature, high pressure aqueous environment, thereby permitting determination of stress corrosion susceptibility of materials in a simple way. The stressing device couples an external piston to an internal tensile sample via a pull rod, with stresses being applied to the sample by pressurizing the piston. The device contains a fitting/seal arrangement including Teflon and weld seals which allow sealing of the internal system pressure and the external piston pressure. The fitting/seal arrangement allows free movement of the pull rod and the piston.

End effects on stress dependent permeability measurements

NASA Astrophysics Data System (ADS)

Korsnes, R. I.; Risnes, R.; Faldaas, I.; Norland, T.

2006-10-01

Permeability changes have been studied under deviatoric stresses for chalk cores and under both hydrostatic- and deviatoric stresses for sandstone cores at room temperature. To avoid end effects in the triaxial cell, caused by friction between the axial steel pistons and the sample, the cell was modified to have pressure outlets from the mid-section of the sample with pressure tubes connected to the outside of the cell for pressure recording. Both permeabilities over the mid-section and over the total core were determined during the action of stresses. The chalk cores with permeability in the range of 1-3 × 10 - 15 m 2 and porosity of about 40-45% were flooded with methanol, while the sandstone cores with permeability values varying from 8 to 100 × 10 - 15 m 2 and porosity of about 30% were flooded with a mineral oil. Major observations were: For the chalk cores, 4 out of 8 samples showed a mid-section permeability with a factor of 1.2 to 1.4 higher than the overall permeability, the remaining 4 samples did not show differences in permeability values taking into account the error on measurements. For the sandstone samples, the mid-section permeability was a factor of 1.2 to 2.4 higher than the overall permeability. In all cases during the deviatoric phase, the change in permeability was rather small, even if the tests were run beyond the yield point. The permeability generally decreased with increasing hydrostatic stresses.

A pressure core ultrasonic test system for on-board analysis of gas hydrate-bearing sediments under in situ pressures.

PubMed

Yang, Lei; Zhou, Weihua; Xue, Kaihua; Wei, Rupeng; Ling, Zheng

2018-05-01

The enormous potential as an alternative energy resource has made natural gas hydrates a material of intense research interest. Their exploration and sample characterization require a quick and effective analysis of the hydrate-bearing cores recovered under in situ pressures. Here a novel Pressure Core Ultrasonic Test System (PCUTS) for on-board analysis of sediment cores containing gas hydrates at in situ pressures is presented. The PCUTS is designed to be compatible with an on-board pressure core transfer device and a long gravity-piston pressure-retained corer. It provides several advantages over laboratory core analysis including quick and non-destructive detection, in situ and successive acoustic property acquisition, and remission of sample storage and transportation. The design of the unique assembly units to ensure the in situ detection is demonstrated, involving the U-type protecting jackets, transducer precession device, and pressure stabilization system. The in situ P-wave velocity measurements make the detection of gas hydrate existence in the sediments possible on-board. Performance tests have verified the feasibility and sensitivity of the ultrasonic test unit, showing the dependence of P-wave velocity on gas hydrate saturation. The PCUTS has been successfully applied for analysis of natural samples containing gas hydrates recovered from the South China Sea. It is indicated that on-board P-wave measurements could provide a quick and effective understanding of the hydrate occurrence in natural samples, which can assist further resource exploration, assessment, and subsequent detailed core analysis.

A pressure core ultrasonic test system for on-board analysis of gas hydrate-bearing sediments under in situ pressures

NASA Astrophysics Data System (ADS)

Yang, Lei; Zhou, Weihua; Xue, Kaihua; Wei, Rupeng; Ling, Zheng

2018-05-01

The enormous potential as an alternative energy resource has made natural gas hydrates a material of intense research interest. Their exploration and sample characterization require a quick and effective analysis of the hydrate-bearing cores recovered under in situ pressures. Here a novel Pressure Core Ultrasonic Test System (PCUTS) for on-board analysis of sediment cores containing gas hydrates at in situ pressures is presented. The PCUTS is designed to be compatible with an on-board pressure core transfer device and a long gravity-piston pressure-retained corer. It provides several advantages over laboratory core analysis including quick and non-destructive detection, in situ and successive acoustic property acquisition, and remission of sample storage and transportation. The design of the unique assembly units to ensure the in situ detection is demonstrated, involving the U-type protecting jackets, transducer precession device, and pressure stabilization system. The in situ P-wave velocity measurements make the detection of gas hydrate existence in the sediments possible on-board. Performance tests have verified the feasibility and sensitivity of the ultrasonic test unit, showing the dependence of P-wave velocity on gas hydrate saturation. The PCUTS has been successfully applied for analysis of natural samples containing gas hydrates recovered from the South China Sea. It is indicated that on-board P-wave measurements could provide a quick and effective understanding of the hydrate occurrence in natural samples, which can assist further resource exploration, assessment, and subsequent detailed core analysis.

Methane Hydrate Recovered From A Mud Volcano in Santa Monica Basin, Offshore Southern California

NASA Astrophysics Data System (ADS)

Normark, W. R.; Hein, J. R.; Powell, C. L.; Lorenson, T. D.; Lee, H. J.; Edwards, B. D.

2003-12-01

In July 2003, a short (2.1 m) piston core from the summit of a mud volcano recovered methane hydrate at a water depth of 813 m in Santa Monica Basin. The discovery core penetrated into in the hydrate as evidenced by chunks of ice and violent degassing of the core section between 162 and 212 cm depth. The core consists of shell hash and carbonate clasts (to 7-cm long) in silty mud. The methanogenic carbonates are of two types: massive, recrystallized nodular masses with an outer mm-thick sugary patina and a bivalve coquina with carbonate cement. Living clams including the genus Vesicomya, commonly found at cold-seep sites elsewhere, were recovered from the top of the core. Further sampling attempts using piston, gravity, and box corers, all of which were obtained within 15 m of the discovery core, recovered olive-brown silty mud with variable amounts of whole and fragmented bivalve shells and methanogenic carbonate fragments characteristic of cold-seep environments. Gases collected in cores adjacent to the discovery core contain elevated amounts of methane and trace amounts of heavier hydrocarbon gases, indicating some component from thermogenic sources. Hydrogen sulfide was also detected in these sediment samples. Vertical channels in one core may have served as fluid pathways. The existence of hydrate at such a shallow depth in the sediment was unexpected, however, the presence of Vesicomya and hydrogen sulfide indicate that the mud volcano is a site of active methane venting. The mud volcano, which is about 24 km west-southwest of Redondo Beach, is about 300 m in diameter at the base. No internal structure is resolved on either high resolution deep-tow boomer or single-channel air-gun profiles, most likely as a result of the gas content and sediment deformation. The diapiric structure has ascended through well-bedded sediment on the lower slope of the basin, producing as much as 30 m of bathymetric relief. It is located in an area where strike-slip motion along the San Pedro Basin fault zone to the south is replaced by convergent motion to the north. The source horizon for the gas in the hydrate is unknown but appears to be collecting in beds as shallow as 200 m below the regional seafloor based on the presence of a strong and irregular reflection interval.

Examination of the Asian Monsoon: Ongoing Studies from IODP Expedition 346

NASA Astrophysics Data System (ADS)

Murray, R. W.; Tada, R.; Alvarez Zarikian, C. A.

2014-12-01

IODP Expedition 346 (Asian Monsoon) tested the hypothesis that Plio-Pleistocene uplift of the Himalaya and Tibetan Plateau, and/or emergence and growth of the northern hemisphere ice sheets and establishment of the two discrete modes of Westerly Jet circulation, is the cause of the millennial-scale variability of the East Asian summer monsoon (EASM) and amplification of Dansgaard-Oeschger cycles. We also examined whether the nature and strength of flow through the Tsushima Strait (which is strongly affected by EASM precipitation, sea level changes, and EAWM cooling) influenced surface and deepwater conditions of the Japan, Yamato, and Ulleung Basins. During only six weeks of drilling, Expedition 346 recovered 6135.3 m of core, which established an IODP record for the amount of recovered material. Because of recent advances in drilling technology and newly developed analytical tools, we were able to examine records that were impossible to acquire even a few years ago. The newly engineered half piston core system recovered the deepest piston core in DSDP/ODP/IODP history (490.4 m in Hole U1427A), which was reached by continuous piston coring from the seafloor. These advances delivered new surprises. We recovered pristine dark-light laminae from approximately 8 Ma sediment from 275 m below the seafloor at Site U1425 (Yamato Rise) and from 210 m below the seafloor (10-12 Ma) at Site U1430 in the Ulleung Basin. Aggressive sampling for geochemistry provided important constraints on the diagenetic and chemical environments throughout these marginal seas, and yet did not negatively compromise paleoceanographic objectives. We are extending earlier pioneering results of the Quaternary dark and light layers in these basins and which record variations of EASM precipitation over South China. Drilling in the East China Sea is providing an excellent record of EASM precipitation because its surface water salinity and temperature during summer is significantly influenced by Yangtze River discharge. Ash records are providing calibrated stratigraphic control and improving understanding of arc history. Interpreting these and other results in the context of other IODP drilling expeditions, such as Expedition 349 to the South China Sea, will be critical to develop a holistic understanding of the Asian monsoon system.

Vapor-rich Hydrothermal Fluid Migration Within Pumiceous Sediment in the Iheya North Knoll, Okinawa Trough

NASA Astrophysics Data System (ADS)

Ishibashi, J.; Suzuki, R.; Hamasaki, H.; Yamanaka, T.; Chiba, H.; Tsunogai, U.; Ijiri, A.; Nakagawa, S.; Nunoura, T.; Takai, K.; Kinoshita, M.; Ashi, J.

2007-12-01

The newly developed ROV NSS (Navigable Sampling System) enabled pin-point piston core sampling from the active hydrothermal field. In the Iheya North hydrothermal field in the mid-Okinawa Trough (27°47.5'N, 126°53.8'E, depth = 1000m), animal colonies are observed not only around the central mound structure (named as NBC) which discharges vigrously high temperature (T=311°C) clear fluid, but also as Calyptogena colony at 200m east from the NBC mound and as tube-worm colony at 250m southeast from the NBC mound. During Leg 3 of KY05-14 cruise (R/V Kaiyo of JAMSTEC) in Jan. 2005, fourn piston cores were successfully recovered with length from 65cm to 250cm. Surface sediments from the Calyptogena colony and the tube-worm colony were revealed as mainly composed of pumiceous sediment. Pore fluids from the Calyptogena Field showed unusual chemistry characterized as very low salinity (Cl=420mM), low Mg concentration, significantly lower Na/Cl ratio than seawater and high methane concentration, which suggests contribution of a vapor-rich hydrothermal component migrating within the pumice layer from the activity center. Moreover, decrease of SO4 accompanied by increase of alkalinity is notable even less than one meter depth below the seafloor. In situ sulfate reduction in the surface sediment caused by entrainment of the hydrothermal component would be a source of hydrogen sulfide that supports Calyptogena colony.

Carbon-Carbon Piston Architectures

NASA Technical Reports Server (NTRS)

Rivers, H. Kevin (Inventor); Ransone, Philip O. (Inventor); Northam, G. Burton (Inventor); Schwind, Francis A. (Inventor)

2000-01-01

An improved structure for carbon-carbon composite piston architectures is disclosed. The improvement consists of replacing the knitted fiber, three-dimensional piston preform architecture described in U.S. Pat.No. 4,909,133 (Taylor et al.) with a two-dimensional lay-up or molding of carbon fiber fabric or tape. Initially, the carbon fabric of tape layers are prepregged with carbonaceous organic resins and/or pitches and are laid up or molded about a mandrel, to form a carbon-fiber reinforced organic-matrix composite part shaped like a "U" channel, a "T"-bar, or a combination of the two. The molded carbon-fiber reinforced organic-matrix composite part is then pyrolized in an inert atmosphere, to convert the organic matrix materials to carbon. At this point, cylindrical piston blanks are cored from the "U"-channel, "T"-bar, or combination part. These blanks are then densified by reimpregnation with resins or pitches which are subsequently carbonized. Densification is also accomplished by direct infiltration with carbon by vapor deposition processes. Once the desired density has been achieved, the piston billets are machined to final piston dimensions; coated with oxidation sealants; and/or coated with a catalyst. When compared to conventional steel or aluminum alloy pistons, the use of carbon-carbon composite pistons reduces the overall weight of the engine; allows for operation at higher temperatures without a loss of strength; allows for quieter operation; reduces the heat loss; and reduces the level of hydrocarbon emissions.

Carbon-Carbon Piston Architectures

NASA Technical Reports Server (NTRS)

Rivers, H. Kevin (Inventor); Ransone, Philip O. (Inventor); Northam, G. Burton (Inventor); Schwind, Francis A. (Inventor)

1999-01-01

An improved structure for carbon-carbon composite piston architectures consists of replacing the knitted fiber, three-dimensional piston preform architecture described in U.S. Pat. No. 4.909,133 (Taylor et al.) with a two-dimensional lay-up or molding of carbon fiber fabric or tape. Initially. the carbon fabric or tape layers are prepregged with carbonaceous organic resins and/or pitches and are laid up or molded about a mandrel. to form a carbon-fiber reinforced organic-matrix composite part shaped like a "U" channel, a "T"-bar. or a combination of the two. The molded carbon-fiber reinforced organic-matrix composite part is then pyrolized in an inert atmosphere, to convert the organic matrix materials to carbon. At this point, cylindrical piston blanks are cored from the "U" channel, "T"-bar, or combination part. These blanks are then densified by reimpregnation with resins or pitches which are subsequently carbonized. Densification is also be accomplished by direct infiltration with carbon by vapor deposition processes. Once the desired density has been achieved, the piston billets are machined to final piston dimensions; coated with oxidation sealants; and/or coated with a catalyst. When compared to conventional steel or aluminum-alloy pistons, the use of carbon-carbon composite pistons reduces the overall weight of the engine; allows for operation at higher temperatures without a loss of strength; allows for quieter operation; reduces the heat loss; and reduces the level of hydrocarbon emissions.

Mineralogic Causes of Variations in Magnetic Susceptibility of Late Pleistocene and Holocene Sediment from Great Salt Lake, Utah

USGS Publications Warehouse

Reynolds, Richard L.; Rosenbaum, Joseph G.; Thompson, Robert S.

2008-01-01

We describe here results of magnetic susceptibility (MS) measurements and magnetic mineralogy of sediments sampled in three cores from the south basin of Great Salt Lake. The cores were obtained in 1996 with a Kullenburg-type piston corer at sites in close proximity: core 96-4 at 41 deg 01.00' N, 112 deg 28.00' W and cores 96-5 and 96-6 at 41 deg 00.09' N, 112 deg 23.05' W. Cores 96-5 (2.16 m long) and -6 combine to make a composite 11.31-m sediment record. Sediments in core 96-4 (5.54 m long) correspond to the approximate depth interval of 3.9-9.6 m in the composite core of 96-5 and -6 based on similarities in the MS records as described below. The central goal of the research was to provide a sediment record of paleoenvironmental change in the northeastern Basin and Range Province over the past 40,000 years. Specific targets included a sedimentologic record of lake-level change combined with a pollen record of climatic change.

Experimental investigations of a uranium plasma pertinent to a self-sustaining plasma source

NASA Technical Reports Server (NTRS)

Schneider, R. T.

1971-01-01

The research is pertinent to the realization of a self-sustained fissioning plasma for applications such as nuclear propulsion, closed cycle MHD power generation using a plasma core reactor, and heat engines such as the nuclear piston engine, as well as the direct conversion of fission energy into optical radiation (nuclear pumped lasers). Diagnostic measurement methods and experimental devices simulating plasma core reactor conditions are discussed. Studies on the following topics are considered: (1) ballistic piston compressor (U-235); (2) high pressure uranium plasma (natural uranium); (3) sliding spark discharge (natural uranium); (4) fission fragment interaction (He-3 and U-235); and (5) nuclear pumped lasers (He-3 and U-235).

Axial and Radial Permeability Evolutions of Compressed Sandstones: End Effects and Shear-band Induced Permeability Anisotropy

NASA Astrophysics Data System (ADS)

Dautriat, Jeremie; Gland, Nicolas; Guelard, Jean; Dimanov, Alexandre; Raphanel, Jean L.

2009-07-01

The influence of hydrostatic and uniaxial stress states on the porosity and permeability of sandstones has been investigated. The experimental procedure uses a special triaxial cell which allows permeability measurements in the axial and radial directions. The core sleeve is equipped with two pressure samplers placed distant from the ends. They provide mid-length axial permeability measure as opposed to the overall permeability measure, which is based on the flow imposed through the pistons of the triaxial cell. The core sleeve is also equipped to perform flows in two directions transverse to the axis of the sample. Two independent measures of axial and complementary radial permeability are thus obtained. Both Fontainebleau sandstone specimens with a porosity of about 5.8% to 8% and low permeability ranging from 2.5 mD to 30 mD and Bentheimer sandstone with a porosity of 24% and a high permeability of 3 D have been tested. The initial axial permeability values obtained by each method are in good agreement for the Fontainebleau sandstone. The Bentheimer sandstone samples present an axial mid-length permeability 1.6 times higher than the overall permeability. A similar discrepancy is also observed in the radial direction, also it relates essentially to the shape of flow lines induced by the radial flow. All the tested samples have shown a higher stress dependency of overall and radial permeability than mid-length permeability. The effect of compaction damage at the pistons/sample and radial ports/sample interfaces is discussed. The relevance of directional permeability measurements during continuous uniaxial compression loadings has been shown on the Bentheimer sandstone until the failure of the sample. We can efficiently measure the influence of brittle failure associated to dilatant regime on the permeability: It tends to increase in the failure propagation direction and to decrease strongly in the transverse direction.

Using giant piston coring within IODP to track past earthquakes in the sedimentary record along the Japan Trench

NASA Astrophysics Data System (ADS)

Strasser, Michael

2017-04-01

"Submarine paleoseismology" is a promising approach to investigate deposits from the deep sea, where earthquakes leave traces preserved in stratigraphic succession. The concept of studying sedimentary event deposits for reconstructing past earthquake history and related impacts to the marine environment is increasingly being applied in various settings. However, at present we lack comprehensive data sets that allow conclusive distinctions between quality and completeness of the paleoseismic archives, as they may relate to different sediment transport, erosion and deposition processes vs. variability of intrinsic seismogenic behavior across different segments. Nevertheless, many recent studies, which are mostly based on conventional 10-m-long cores, demonstrate the potential of the research concept. With ECORD opening their mission specific platform approach to include giant piston coring within IODP, a new horizon has opened up for multi-coring expeditions fully dedicated to the rapidly growing field of submarine paleoseismology. IODP is uniquely positioned to address the complex feedback mechanisms between earthquake shaking and its manifestation in the marine archive, decipher related mass fluxes from the shallow to the deep see and to eventually provide longer records to constrain earthquake recurrence far beyond historical catalogues. Initially building on what sedimentary deposits were generated from the 2011 M9 Tohoku-oki earthquake, the Japan Trench is a promising study area to investigate earthquake-triggered sediment remobilization processes and how they become embedded in the stratigraphic record, and has thus been identified as a primary target for proposing giant piston coring within IODP. In this presentation we summarize recent results and available site survey data collected since the 2011 earthquake, comprising >50, 5-10m long piston and gravity cores from (i) trench-fill and graben-fill basin across the entire trench axis from 36° to 40.3° N (ii), the mid-slope terraces and (ii) from representative slope sites as potential source for sediment remobilization during earthquakes (2) nearly 2000km of high-resolution subbottom acoustic reflection data (Parasound) that reveals striking, up to several meter thick, acoustically transparent bodies interbedded in the otherwise parallel reflection pattern of the trench fill basins. Results from conventional coring covering the last 1500 years reveal good agreement between the sedimentary record and historical documents in the central part of the margin, and shed new lights on earthquake-triggered, gravity flow-driven supply of significant amount of pre-aged carbon to the hadal environment. New cores retrieved from the southern and northernmost part of the Japan Trench during the recent R/V Sonne expedition SO251 confirm the presence of repeated thick turbidite sequences to be further tested for correlation to historic earthquakes along different margin segments. All these observations underpin the great potential for deciphering earthquake related processes from the stratigraphic record of the small deep-sea trench-fill and graben-fill basins in the Japan Trench, the longer-term record of which is only accessible by giant-piston coring and drilling, as proposed by IODP in Proposal 866.

Design of a magnetorheological automotive shock absorber

NASA Astrophysics Data System (ADS)

Lindler, Jason E.; Dimock, Glen A.; Wereley, Norman M.

2000-06-01

Double adjustable shock absorbers allow for independent adjustment of the yield force and post-yield damping in the force versus velocity response. To emulate the performance of a conventional double adjustable shock absorber, a magnetorheological (MR) automotive shock absorber was designed and fabricated at the University of Maryland. Located in the piston head, an applied magnetic field between the core and flux return increases the force required for a given piston rod velocity. Between the core and flux return, two different shaped gaps meet the controllable performance requirements of a double adjustable shock. A uniform gap between the core and the flux return primarily adjusts the yield force of the shock absorber, while a non-uniform gap allows for control of the post-yield damping. Force measurements from sinusoidal displacement cycles, recorded on a mechanical damper dynamometer, validate the performance of uniform and non- uniform gaps for adjustment of the yield force and post-yield damping, respectively.

Contamination Control of Freeze Shoe Coring System for Collection of Aquifer Sands

NASA Astrophysics Data System (ADS)

Homola, K.; van Geen, A.; Spivack, A. J.; Grzybowski, B.; Schlottenmier, D.

2017-12-01

We have developed and tested an original device, the freeze-shoe coring system, designed to recover undisturbed samples of water contained in sand-dominated aquifers. Aquifer sands are notoriously difficult to collect together with porewater from coincident depths, as high hydraulic permeability leads to water drainage and mixing during retrieval. Two existing corer designs were reconfigured to incorporate the freeze-shoe system; a Hydraulic Piston (HPC) and a Rotary (RC) Corer. Once deployed, liquid CO­2 contained in an interior tank is channeled to coils at the core head where it changes phase, rapidly cooling the deepest portion of the core. The resulting frozen core material impedes water loss during recovery. We conducted contamination tests to examine the integrity of cores retrieved during a March 2017 yard test deployment. Perfluorocarbon tracer (PFC) was added to the drill fluid and recovered cores were subsampled to capture the distribution of PFC throughout the core length and interior. Samples were collected from two HPC and one RC core and analyzed for PFC concentrations. The lowest porewater contamination, around 0.01% invasive fluid, occurs in the center of both HPC cores. The greatest contamination (up to 10%) occurs at the disturbed edges where core material contacts drill fluid. There was lower contamination in the core interior than top, bottom, and edges, as well as significantly lower contamination in HPC cores that those recovered with the RC. These results confirm that the freeze-shoe system, proposed for field test deployments in West Bengal, India, can successfully collect intact porewater and sediment material with minimal if any contamination from drill fluid.

Fast 3D Surface Extraction 2 pages (including abstract)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sewell, Christopher Meyer; Patchett, John M.; Ahrens, James P.

Ocean scientists searching for isosurfaces and/or thresholds of interest in high resolution 3D datasets required a tedious and time-consuming interactive exploration experience. PISTON research and development activities are enabling ocean scientists to rapidly and interactively explore isosurfaces and thresholds in their large data sets using a simple slider with real time calculation and visualization of these features. Ocean Scientists can now visualize more features in less time, helping them gain a better understanding of the high resolution data sets they work with on a daily basis. Isosurface timings (512{sup 3} grid): VTK 7.7 s, Parallel VTK (48-core) 1.3 s, PISTONmore » OpenMP (48-core) 0.2 s, PISTON CUDA (Quadro 6000) 0.1 s.« less

Assembly for electrical conductivity measurements in the piston cylinder device

DOEpatents

Watson, Heather Christine [Dublin, CA; Roberts, Jeffrey James [Livermore, CA

2012-06-05

An assembly apparatus for measurement of electrical conductivity or other properties of a sample in a piston cylinder device wherein pressure and heat are applied to the sample by the piston cylinder device. The assembly apparatus includes a body, a first electrode in the body, the first electrode operatively connected to the sample, a first electrical conductor connected to the first electrode, a washer constructed of a hard conducting material, the washer surrounding the first electrical conductor in the body, a second electrode in the body, the second electrode operatively connected to the sample, and a second electrical conductor connected to the second electrode.

JAMSTEC multibeam surveys and submersible dives around the Hawaiian Islands: a collaborative Japan-USA exploration of Hawaii's deep seafloor

USGS Publications Warehouse

Robinson, Joel E.; Eakins, Barry W.; Kanamatsu, Toshiya; Naka, Jiro; Takahashi, Eiichi; Satake, Kenji; Smith, John R.; Clague, David A.; Yokose, Hisayoshi

2006-01-01

This database release, USGS Data Series 171, contains data collected during four Japan-USA collaborative cruises that characterize the seafloor around the Hawaiian Islands. The Japan Agency for Marine-Earth Science and Technology (JAMSTEC) sponsored cruises in 1998, 1999, 2001, and 2002, to build a greater understanding of the deep marine geology around the Hawaiian Islands. During these cruises, scientists surveyed over 600,000 square kilometers of the seafloor with a hull-mounted multibeam seafloor-mapping sonar system (SEA BEAM® 2112), observed the seafloor and collected samples using robotic and manned submersible dives, collected dredge and piston-core samples, and performed single-channel seismic surveys.

Striking similarities in temporal changes to spring sea ice occurrence across the central Canadian Arctic Archipelago over the last 7000 years

NASA Astrophysics Data System (ADS)

Belt, Simon T.; Vare, Lindsay L.; Massé, Guillaume; Manners, Hayley R.; Price, John C.; MacLachlan, Suzanne E.; Andrews, John T.; Schmidt, Sabine

2010-12-01

A 7000 year spring sea ice record for Victoria Strait (ARC-4) and Dease Strait (ARC-5) in the Canadian Arctic Archipelago (CAA) has been determined by quantification of the sea ice diatom-derived biomarker IP 25 in two marine sediment piston cores obtained in 2005. The chronologies of the ARC-4 and ARC-5 cores were determined using a combination of 14C AMS dates obtained from macrobenthic fossils and magnetic susceptibility measurements. The ages of the tops of the piston cores were estimated by matching chemical and physical parameters with those obtained from corresponding box cores. These analyses revealed that, while the top of the ARC-4 piston core was estimated to be essentially modern (ca. 60 cal yr BP), a few hundred years of sediment appeared to be absent from the ARC-5 piston core. Downcore changes to IP 25 fluxes for both cores were interpreted in terms of variations in spring sea ice occurrence, and correlations between the individual IP 25 flux profiles for Victoria Strait, Dease Strait and Barrow Strait (reported previously) were shown to be statistically significant at both 50 and 100-year resolutions. The IP 25 data indicate lower spring sea ice occurrences during the early part of the record (ca. 7.0-3.0 cal kyr BP) and for parts of the late Holocene (ca. 1.5-0.8 cal kyr BP), especially for the two lower latitude study locations. In contrast, higher spring sea ice occurrences existed during ca. 3.0-1.5 cal kyr BP and after ca. 800 cal yr BP. The observation of, consecutively, lower and higher spring sea ice occurrence during two periods of the late Holocene, coincides broadly with the Medieval Warm Period and Little Ice Age epochs, respectively. The IP 25 data are complemented by particle size and mineralogical data, although these may alternatively reflect changes in sea level at the study sites. The IP 25 data are also compared to previous proxy-based determinations of palaeo sea ice and palaeoclimate for the CAA, including those based on bowhead whale remains and dinocyst assemblages. The spatial consistency in the proxy data which, most notably, indicates an increase in spring sea ice occurrence around 3 cal kyr BP, provides a potentially useful benchmark for the termination of the Holocene Thermal Maximum for the central CAA.

A Composite Depth Scale for Sediments from Crevice Lake, Montana

USGS Publications Warehouse

Rosenbaum, J.G.; Skipp, G.; Honke, J.; Chapman, C.

2010-01-01

As part of a study to derive records of past environmental change from lake sediments in the western United States, a set of cores was collected from Crevice Lake, Montana, in late February and early March 2001. Crevice Lake (latitude 45.000N, longitude 110.578W, elevation 1,713 meters) lies adjacent to the Yellowstone River at the north edge of Yellowstone National Park. The lake is more than 31 meters deep and has a surface area of 7.76 hectares. The combination of small surface area and significant depth promote anoxic bottom-water conditions that preserve annual laminations (varves) in the sediment. Three types of cores were collected through the ice. The uppermost sediments were obtained in freeze cores that preserved the sediment water interface. Two sites were cored with a 5-centimeter diameter corer. Five cores were taken with a 2-meter-long percussion piston corer. The percussion core uses a plastic core liner with an inside diameter of 9 centimeters. Coring was done at two sites. Because of the relatively large diameter of the percussion cores, samples from these cores were used for a variety of analyses including pollen, charcoal, diatoms, stable isotopes, organic and inorganic carbon, elemental analyses, and magnetic properties.

Testing of a scanning adiabatic calorimeter with Joule effect heating of the sample

NASA Astrophysics Data System (ADS)

Barreiro-Rodríguez, G.; Yáñez-Limón, J. M.; Contreras-Servin, C. A.; Herrera-Gomez, A.

2008-01-01

We evaluated a scanning adiabatic resistive calorimeter (SARC) developed to measure the specific enthalpy of viscous and gel-type materials. The sample is heated employing the Joule effect. The cell is constituted by a cylindrical jacket and two pistons, and the sample is contained inside the jacket between the two pistons. The upper piston can slide to allow for thermal expansion and to keep the pressure constant. The pistons also function as electrodes for the sample. While the sample is heated through the Joule effect, the electrodes and the jacket are independently heated to the same temperature of the sample using automatic control. This minimizes the heat transport between the sample and its surroundings. The energy to the sample is supplied by applying to the electrodes an ac voltage in the kilohertz range, establishing a current in the sample and inducing electric dissipation. This energy can be measured with enough exactitude to determine the heat capacity. This apparatus also allows for the quantification of the thermal conductivity by reproducing the evolution of the temperature as heat is introduced only to one of the pistons. To this end, the system was modeled using finite element calculations. This dual capability proved to be very valuable for correction in the determination of the specific enthalpy. The performance of the SARC was evaluated by comparing the heat capacity results to those obtained by differential scanning calorimetry measurements using a commercial apparatus. The analyzed samples were zeolite, bauxite, hematite, bentonite, rice flour, corn flour, and potato starch.

The Pleistocene Eastern Equatorial Pacific: Insights from a New Carnegie Platform Stratigraphic Record

NASA Astrophysics Data System (ADS)

Gwizd, S.; Lea, D. W.

2016-12-01

Renewed interest in a classic Eastern Equatorial Pacific paleoceanographic site at 3° 35.85' S, 83° 57.79' W, previous site of cores V19-29 and TR163-31, prompted a re-coring in 2009 using the recently developed CDH giant piston coring system on cruise KNR195-5. Giant piston core CDH-36 (3225 m depth, 42.61 m length) nearly triples the length of previous cores at this site. When spliced together with companion multicore MC-34A (0.36 m length), these two cores generate continuous stratigraphy throughout most of the middle Pleistocene, and include recognized stratigraphic tie points ash layer "L" (Ninkovich and Shackleton, 1975) and the extinction of pink G. ruber. A new age model utilizing Bayesian analysis of 17 N. dutertrei radiocarbon dates in MC-34A and the top 3.4 m of CDH-36, and alignment of a new CDH-36 δ18O record with the LR04 benthic stack (Lisiecki and Raymo, 2005), demonstrates that this new "Carnegie Platform" (CP) record extends from 0 to 720 ka (MIS 18), tripling the timescale of previous studies, with an average sedimentation rate of 7 cm/kyr. The CP C. wuellerstorfi δ18O and δ13C records reveal strong consistencies in timing and extent of glacial and interglacial episodes with previously studied regional records. Coarse fraction percentage (%CF) ([coarse fraction/bulk dry sample] * 100) is also evaluated throughout the CP core in order to qualitatively assess dissolution cycles. The CP %CF dataset primarily records Pleistocene dissolution cycles, yet exhibits variability representative of potential local bathymetric and hydrographic effects. The timing of %CF cyclicity is consistent with processes which affect basin-wide calcium carbonate dissolution cycles, including changes in terrestrial carbon input to the oceans and changes in water mass ventilation (Shackleton, 1977; Toggweiler et al., 2006; Sexton and Barker, 2012). Establishing the stratigraphy of the CP record provides the first step towards a more thorough and extended analysis of this important Eastern Equatorial Pacific site.

Strontium Isotope Dating of Metalliferous Sediment in the SW Pacific Basin

NASA Astrophysics Data System (ADS)

Stancin, A. M.; Gleason, J. D.; Owen, B. M.; Rea, D. K.; Moore, T. C.; Hendy, I. L.; Lyle, M. W.; Blum, J. D.

2007-12-01

A 2 million km2 region virtually devoid of sediment was identified in the remote SW Pacific Basin during the TUIM- 3 2005 drill site survey cruise. This region, termed the "South Pacific Bare Zone", comprises ocean floor dating back to the Late Cretaceous. Within the Bare Zone, a small (1km2) abyssal valley containing sediment to a depth of 24 m was sampled using a large diameter piston core (MV0502-15JC, 31 ° 42.194'S, 143 ° 30.331'W), leading to recovery of 8.35 m of metalliferous sediment at 5082 m water depth. Fish-teeth Sr-isotope stratigraphy reveals a continuous record of sedimentation from 31 Ma to present at this site. The fish teeth age-depth profile and INAA geochemistry reveal an exponentially decreasing hydrothermal flux, with sedimentation rates approaching 0.05 mm/kyr after 20 Ma. The source of hydrothermal activity at this site was likely the Pacific- Farallon Ridge, which went extinct at 20 Ma. A second piston core (MV0502-16JC; 28 ° 05.151'S, 140 ° 14.140'W) was collected near MacDonald Seamounts located on the southeastern end of the Cook-Austral island chain outside the Bare Zone and recovered 10.5 m of hydrothermal sediment and biogenic ooze. The lower 65 cm of the core consists of a coccolith ooze. From 10 mbsf depth to 1.5 mbsf depth, the core contians reddish black zeolitic clay, while the upper 1.5 mbsf contains biogenic ooze associated with abundant Late Pleistocene foraminifera remains. Concordant nannofossil and fish teeth ages at the base of the core (27-28 Ma), and Pleistocene ages near the top of the core reinforce the validity of the Sr fish teeth method for dating hydrothermal cores. These independent records suggest that regional hydrothermal activity during the Oligocene may have been related to a series of late Eocene/early Oligocene ridge jumps, propagating rifts and seafloor spreading centers that accompanied large-scale plate tectonic reorganization of South Pacific seafloor.

Towards improved cirque glacier reconstructions: differentiating glacial- from non-glacial sediments by means of environmental magnetism.

NASA Astrophysics Data System (ADS)

Kvisvik, Bjørn Christian; Paasche, Øyvind; Olaf Dahl, Svein

2014-05-01

Skriufonnen, a small cirque glacier (0.4 km2) in Southern Norway, has been monitored for the last 10 years, revealing a short response time to on-going climate change. This is the only remaining glacier in the central mountain massif known as Rondane where investigations of past climate variability are scarce. A series of short (HTH, n=8) and long (piston, n=6) cores from two lakes located downstream of Skriufonnen were retrieved and sediments were dated and analysed. In order to complement and validate lake sediment interpretations i.e., the potential connection to glacier variability, a number of soil samples was collected from the surrounding catchment. The six 110 mm piston cores (< 3.1 m length) and eight sediment surface cores were analysed for grain size distribution, geochemical elements (ITRAX XRF-scanning), organic matter content (LOI), magnetic parameters (magnetic susceptibility; surface and bulk), anhysteretic remanent magnetization (ARM) and Saturation Isothermal remanent magnetizations (sIRM). Consistent age-depth relationships were obtained by AMS-C14 and Pb210 dates showing that the cores cover at least the last 10 000 years. High-resolution analysis (XRF and MS) reveals centennial trends, but also distinct changes in frequency and amplitude. A quiescent period during the Holocene Thermal Optimum (9-6 ka) is followed by a sudden onset of Neoglacial (3.8 ka) activity peaking at 2.4 ka. The Little Ice Age (LIA) peaked at 1800 AD. A weak magnetic signal is observed in all cores. This is explained by the fact that Rondane is made of Sparagmite, an arkosic sandstone partly consisting of metamorphosed sandstone and conglomerate with high content of quarts (SiO2) (between 80 to 87 %) and Feldspar. The Sparagmite is resistant to chemical weathering, making the soils dry and sandy. Catchment sediment samples, running in a transect all the way up from the lakes to the glacier snout were sieved into various size classes (250, 125, 63, 38, 20 μm) prior to measuring bulk susceptibility (Ξbulk) at 293K and 77K. The ratio between the two measurements indicates the relative amount of paramagnetic versus ferromagnetic minerals, and results indicate not only that the finest fractions increase in strength as one gets closer to the glacier front, but also that there are long periods in the cores which is dominated by paramagnetic minerals. The approach employed here suggests that the combination of catchment samples with high-resolution analysis of lake sediment cores provide a more accurate reconstruction of past glacier variability, and has resulted in the first continuous cirque glacier reconstruction from this area.

HIGH PRESSURE GAS REGULATOR

DOEpatents

Ramage, R.W.

1962-05-01

A gas regulator operating on the piston and feedback principle is described. The device is particularly suitable for the delicate regulation of high pressure, i.e., 10,000 psi and above, gas sources, as well as being perfectly adaptable for use on gas supplies as low as 50 psi. The piston is adjustably connected to a needle valve and the movement of the piston regulates the flow of gas from the needle valve. The gas output is obtained from the needle valve. Output pressure is sampled by a piston feedback means which, in turn, regulates the movement of the main piston. When the output is other than the desired value, the feedback system initiates movement of the main piston to allow the output pressure to be corrected or to remain constant. (AEC)

Modern benthic foraminifer distribution in the Amerasian Basin, Arctic Ocean

USGS Publications Warehouse

Ishman, S.E.; Foley, K.M.

1996-01-01

A total of 38 box cores were collected from the Amerasian Basin, Arctic Ocean during the U.S. Geological Survey 1992 (PI92-AR) and 1993 (PI93-AR) Arctic Cruises aboard the U.S. Coast Guard Icebreaker Polar Star. In addition, the cruises collected geophysical data, piston cores and hydrographic data to address the geologic and oceanographic history of the western Arctic Ocean. This paper reports the results of the quantitative analyses of benthic foraminifer distribution data of the total (live + dead) assemblages derived from 22 box core-top samples. The results show that a distinct depth distribution of three dominant benthic foraminifer assemblages, the Textularia spp. - Spiroplectammina biformis, Cassidulina teretis and Oridorsalis tener - Eponides tumidulus Biofacies are strongly controlled by the dominant water masses within the Canada Basin: the Arctic Surface Water, Arctic Intermediate Water and Canada Basin Deep Water. The faunal distributions and their oceanographic associations in the Canada Basin are consistent with observations of benthic foraminifer distributions from other regions within the Arctic Ocean.

Hydraulic pump with in-ground filtration and monitoring capability

DOEpatents

Hopkins, C.D.; Livingston, R.R.; Toole, W.R. Jr.

1995-01-01

A hydraulically operated pump is described for in-ground filtering and monitoring of wells or other fluid sources, including a hollow cylindrical pump housing with an inlet and an outlet, filtering devices positioned in the inlet and the outlet, a piston that fits slidably within the pump housing, and an optical cell in fluid communication with the pump housing. A conduit within the piston allows fluid communication between the exterior and one end of the piston. A pair of O-rings form a seal between the inside of the pump housing and the exterior of the piston. A flow valve positioned within the piston inside the conduit allows fluid to flow in a single direction. In operation, fluid enters the pump housing through the inlet, flows through the conduit and towards an end of the pump housing. The piston then makes a downward stroke closing the valve, thus forcing the fluid out from the pump housing into the optical cell, which then takes spectrophotometric measurements of the fluid. A spring helps return the piston back to its starting position, so that a new supply of fluid may enter the pump housing and the downward stroke can begin again. The pump may be used independently of the optical cell, as a sample pump to transport a sample fluid from a source to a container for later analysis.

Hydraulic pump with in-ground filtration and monitoring capability

DOEpatents

Hopkins, C.D.; Livingston, R.R.; Toole, W.R. Jr.

1996-10-29

A hydraulically operated pump is described for in-ground filtering and monitoring of waters or other fluid sources, includes a hollow cylindrical pump housing with an inlet and an outlet, filtering devices positioned in the inlet and the outlet, a piston that fits slidably within the pump housing, and an optical cell in fluid communication with the pump housing. A conduit within the piston allows fluid communication between the exterior and one end of the piston. A pair of o-rings form a seal between the inside of the pump housing and the exterior of the piston. A flow valve positioned within the piston inside the conduit allows fluid to flow in a single direction. In operation, fluid enters the pump housing through the inlet, flows through the conduit and towards an end of the pump housing. The piston then makes a downward stroke closing the valve, thus forcing the fluid out from the pump housing into the optical cell, which then takes spectrophotometric measurements of the fluid. A spring helps return the piston back to its starting position, so that a new supply of fluid may enter the pump housing and the downward stroke can begin again. The pump may be used independently of the optical cell, as a sample pump to transport a sample fluid from a source to a container for later analysis. 5 figs.

Hydraulic pump with in-ground filtration and monitoring capability

DOEpatents

Hopkins, Charles D.; Livingston, Ronald R.; Toole, Jr., William R.

1996-01-01

A hydraulically operated pump for in-ground filtering and monitoring of ws or other fluid sources, including a hollow cylindrical pump housing with an inlet and an outlet, filtering devices positioned in the inlet and the outlet, a piston that fits slidably within the pump housing, and an optical cell in fluid communication with the pump housing. A conduit within the piston allows fluid communication between the exterior and one end of the piston. A pair of o-rings form a seal between the inside of the pump housing and the exterior of the piston. A flow valve positioned within the piston inside the conduit allows fluid to flow in a single direction. In operation, fluid enters the pump housing through the inlet, flows through the conduit and towards an end of the pump housing. The piston then makes a downward stroke closing the valve, thus forcing the fluid out from the pump housing into the optical cell, which then takes spectrophotometric measurements of the fluid. A spring helps return the piston back to its starting position, so that a new supply of fluid may enter the pump housing and the downward stroke can begin again. The pump may be used independently of the optical cell, as a sample pump to transport a sample fluid from a source to a container for later analysis.

Collection, analysis, and age-dating of sediment cores from 56 U.S. lakes and reservoirs sampled by the U.S. Geological Survey, 1992-2001

USGS Publications Warehouse

Van Metre, Peter; Wilson, Jennifer T.; Fuller, Christopher C.; Callender, Edward; Mahler, Barbara J.

2004-01-01

The U.S. Geological Survey Reconstructed Trends National Synthesis study collected sediment cores from 56 lakes and reservoirs between 1992 and 2001 across the United States. Most of the sampling was conducted as part of the National Water-Quality Assessment (NAWQA) Program. The primary objective of the study was to determine trends in particle-associated contaminants in response to urbanization; 47 of the 56 lakes are in or near one of 20 U.S. cities. Sampling was done with gravity, piston, and box corers from boats and push cores from boats or by wading, depending on the depth of water and thickness of sediment being sampled. Chemical analyses included major and trace elements, organochlorine pesticides, polychlorinated biphenyls, polycyclic aromatic hydrocarbons, cesium-137, and lead-210. Age-dating of the cores was done on the basis of radionuclide analyses and the position of the pre-reservoir land surface in the reservoir and, in a few cases, other chemical or lithologic depth-date markers. Dates were assigned in many cores on the basis of assumed constant mass accumulation between known depth-date markers. Dates assigned were supported using a variety of other date markers including first occurrence and peak concentrations of DDT and polychlorinated biphenyls and peak concentration of lead. A qualitative rating was assigned to each core on the basis of professional judgment to indicate the reliability of age assignments. A total of 122 cores were collected from the 56 lakes and age dates were assigned to 113 of them, representing 54 of the 56 lakes. Seventy-four of the 122 cores (61 percent) received a good rating for the assigned age dates, 28 cores (23 percent) a fair rating, and 11 cores (9 percent) a poor rating; nine cores (7 percent) had no dates assigned. An analysis of the influence of environmental factors on the apparent quality of age-dating of the cores concluded that the most important factor was the mass accumulation rate (MAR) of sediment: the greater the MAR, the better the temporal discretization in the samples and the less important the effects of postdepositional sediment disturbance. These age-dated sediment cores provide the basis for local-, regional-, and national-scale interpretations of water-quality trends.

Development of free-piston Stirling engine performance and optimization codes based on Martini simulation technique

NASA Technical Reports Server (NTRS)

Martini, William R.

1989-01-01

A FORTRAN computer code is described that could be used to design and optimize a free-displacer, free-piston Stirling engine similar to the RE-1000 engine made by Sunpower. The code contains options for specifying displacer and power piston motion or for allowing these motions to be calculated by a force balance. The engine load may be a dashpot, inertial compressor, hydraulic pump or linear alternator. Cycle analysis may be done by isothermal analysis or adiabatic analysis. Adiabatic analysis may be done using the Martini moving gas node analysis or the Rios second-order Runge-Kutta analysis. Flow loss and heat loss equations are included. Graphical display of engine motions and pressures and temperatures are included. Programming for optimizing up to 15 independent dimensions is included. Sample performance results are shown for both specified and unconstrained piston motions; these results are shown as generated by each of the two Martini analyses. Two sample optimization searches are shown using specified piston motion isothermal analysis. One is for three adjustable input and one is for four. Also, two optimization searches for calculated piston motion are presented for three and for four adjustable inputs. The effect of leakage is evaluated. Suggestions for further work are given.

Variations in the depths of sulfate-methane transition zone (SMTZ) in UBGH2-6 drilling site in Ulleung Basin, East sea of Korea

NASA Astrophysics Data System (ADS)

Kim, Y.; Chun, J. H.; Bahk, J. J.; Ryu, B. J.; Um, I. K.

2016-12-01

The second Ulleung Basin Gas hydrate Drilling Expedition (UBGH2) was conducted in the Ulleung Basin, East Sea of Korea in 2010. Gas hydrates were observed in depth interval from 140 mbsf (meter below seafloor) to 160 mbsf in core sediment taken from UBGH2-6 drilling site, located in the north-western part of the basin (2,164 m water depth). To characterize the geochemical process for UBGH2-6 core sediments, pore fluid samples and headspace gas samples were extracted from core sediments and analyzed SO42- and CH4 concentrations. Based on SO42- and CH4 concentrations, sulfate-methane transition zone (SMTZ), where SO42- is depleted to zero and CH4 starts to increase was defined at a depth of approximately 6.50 mbsf in 2010. And in order to identify the variations in the depths of SMTZ at UBGH2-6 drilling site since 2010 (UBGH2), whole-round piston cores were collected from UBGH2-6 drilling site from 2013 to 2015. We analyzed SO42- and CH4 concentrations and identified the SMTZ for the last 3 years. The depths of SMTZ for the cores obtained from 2013, 2014 and 2015 are approximately 3.50 mbsf, 5.00 mbsf, and 5.00 mbsf respectively. The analysis results indicate that the SMTZ in 2013, 2014, and 2015 are shallower than the SMTZ of 2010.

Phase Equilibria of a S- and C-Poor Lunar Core

NASA Technical Reports Server (NTRS)

Righter, K.; Pando, K.; Go, B. M.; Danielson, L. R.; Habermann, M.

2016-01-01

The composition of the lunar core can have a large impact on its thermal evolution, possible early dynamo creation, and physical state. Geochemical measurements have placed better constraints on the S and C content of the lunar mantle. In this study we have carried out phase equilibrium studies of geochemically plausible S- and C-poor lunar core compositions in the Fe-Ni-S-C system, and apply them to the early history of the Moon. We chose two bulk core compositions, with differing S and C content based on geochemical analyses of S and C trapped melts in Apollo samples, and on the partitioning of S and C between metal and silicate. This approach allowed calculation of core S and C contents - 90% Fe, 9% Ni, 0.5% C, and 0.375% S by weight; a second composition contained 1% each of S and C. Experiments were carried out from 1473K to 1973K and 1 GPa to 5 GPa, in piston cylinder and multi- anvil apparatuses. Combination of the thermal model of with our results, shows that a solid inner core (and therefore initiation of a dynamo) may have been possible in the earliest history of the Moon (approximately 4.2 Ga ago), in agreement with. Thus a volatile poor lunar core may explain the thermal and magnetic history of the Moon.

Gas and porewater composition of shallow sediments in the Tuaheni Basin, New Zealand

NASA Astrophysics Data System (ADS)

Rose, P. S.; Coffin, R. B.; Yoza, B.; Boyd, T. J.; Crutchley, G. J.; Mountjoy, J. J.; Pecher, I. A.

2015-12-01

Seismic profiles collected during previous investigations on the Hikurangi Margin, off the North Island, New Zealand showed bottom simulating reflectors (BSRs), which are generally indicative of the presence of free gas. Further, double BSRs clearly identified in the Tuaheni Basin were hypothesized to result from differences in gas composition and fluid migration. During a cruise on the RV Tangaroa in June 2015 (TAN 1508) additional seismic data were collected and used to identify piston coring targets. Coring locations were selected to sample around BSR pinch-outs and possible fluid migration pathways to determine gas composition and flux. Shallow sediments collected in June 2015 in the Tuaheni Basin had relatively low sediment headspace CH4 concentrations (6000ppm. Higher molecular weight alkanes were not detected in the sediment headspace gas at any location. Sediment porewater sulfate, chloride and sulfide concentrations will be presented with CH4concentration profiles and geophysical data.

Application of Rhizon Porewater Samplers to Shipboard Operations, IODP Expedition 308, Northeast Gulf of Mexico

NASA Astrophysics Data System (ADS)

Gilhooly, W. P.; Macko, S. A.; Flemings, P. B.

2005-12-01

Pleistocene and Recent sediments within the Brazos-Trinity and Ursa Basins (northwestern Gulf of Mexico) were largely deposited by turbidity currents and have been deformed by a number of mass transport events. The geochemical composition of interstitial waters was determined in order to assess fluid flow within these sediments. Typical porewater sampling resolution, using advanced piston coring and the traditional Manheim squeezer technique, is approximately one sample every other core (20m) with the highest working resolution at one sample every 1.5m. In this study, Rhizon soil moisture samplers were used to attain high-resolution porewater profiles within sea floor surface sediments and for permeable sediments at depth. The small dimensions (2mm x 30mm) and pore-size (1μm) of the devices enable high-frequency placement within a core, specific targeting of the sequence of interest, and do not require sediment removal from the core, or filtering of extracted porewaters. Initial shipboard analyses derived from sediments at the Ursa Basin (Site 1322) indicate a linear decrease in salinity with depth at U1322 where the overpressure gradient is thought to be greatest. The less saline waters with depth lends evidence for potential mixing between deep-seated fluids and low salinity ones derived from the Blue Unit and seawater. Isotopic composition and concentrations of sulfur species (SO4 and H2S) dissolved in porewaters, as well as, ionic compositions (Cl, Na, K, Ca, Mg) and chemical composition of associated sediments (%C, %N, 13C, and 15N) are compared with chemical results obtained with squeezers.

Resonant Acoustic Measurement of Vapor Phase Transport Phenomenon

NASA Astrophysics Data System (ADS)

Schuhmann, R. J.; Garrett, S. L.; Matson, J. V.

2002-12-01

A major impediment to accurate non steady-state diffusion measurements is the ability to accurately measure and track a rapidly changing gas concentration without disturbing the system. Non-destructive methods that do not interfere with system dynamics have been developed in the past. These methods, however, have tended to be cumbersome or inaccurate at low concentrations. A new experimental approach has been developed to measure gaseous diffusion in free air and through porous materials. The method combines the traditional non steady-state laboratory methodology with resonant acoustic gas analysis. A phase-locked-loop (PLL) resonance frequency tracker is combined with a thermally insulated copper resonator. A piston sealed with a metal bellows excites the fundamental standing wave resonance of the resonator. The PLL maintains a constant phase difference (typically 90§) between the accelerometer mounted on the piston and a microphone near the piston to track the resonance frequency in real time. A capillary or glass bead filled core is fitted into an o-ring sealed opening at the end of the resonator opposite the bellows. The rate at which the tracer gas is replaced by air within the resonator is controlled by the diffusion coefficient of the gas in free air through the capillary (DA) or by the effective diffusion coefficient of the gas through the core (De). The mean molecular weight of the gas mixture in the resonator is directly determined six times each minute from the ratio of the absolute temperature to the square of the fundamental acoustic resonance frequency. Average system stability (temperature divided by frequency squared) is better than 350 ppm. DA values for a 0.3-inch diameter capillary were in excellent agreement with published values. De values for porous media samples (0.5 mm glass beads) of four different lengths (1 through 4 inches) using three different tracer gases (He, CH4, Kr) will be reported. Comments will be offered regarding tracer gas selection and device orientation and their effect on experimental results. [Work supported by the Office of Naval Research.

Late Quaternary paleohydrology deduced from new marine sediment cores taken on the proximal Amazon continental margin

NASA Astrophysics Data System (ADS)

Nace, T.; Baker, P. A.; Dwyer, G. S.; Hollander, D. J.; Silva, C. G.

2010-12-01

Throughout the late Quaternary the Amazon Basin has been influenced by abrupt North-South climate forcing and has undergone several large climate variations as recorded in previously reported speleothem records. Despite its importance in the global carbon cycle there are few continuous, high-resolution records of the Amazon Basin that date back to and beyond the last glacial period. In this study, we report the first results of a marine geological expedition to the Amazon continental shelf and fan region. During this expedition we collected eight ~30 meter piston cores along with gravity, box and multicores. At both sites we undertook complementary multibeam and high resolution seismic reflection profiling. Analyses will be presented from two sets of box/gravity/piston cores. One core (32m) is from a high sedimentation site on the northern flank of the main submarine canyon within the Amazon Fan complex at 1700m water depth. The other core (30m) is located on a seamount to the south of the Amazon Fan complex at 3100m water depth. A mixed assemblage of foraminifera is used for 14C dating to obtain an age model and bulk organic geochemistry is analyzed to determine percent organic carbon, C/N ratios, δ13C and δ15N. The cores were continuously measured shipboard for magnetic susceptibility and gamma density using a GEOTEK logger. These findings uncover the contribution of pelagic and terrestrial organic matter, whether the terrigenous carbon is derived from C3 versus C4 vegetation, and whether the marine organic matter is composed of phytoplankton or marine algae.

Rheology of welding: experimental constraints

NASA Astrophysics Data System (ADS)

Quane, S. L.; Russell, J. K.; Kennedy, L. A.

2003-04-01

The rheological behavior of pyroclastic deposits during welding is incompletely understood and is based on a surprisingly small number of experimental studies. Previous pioneering experimental studies were done on small (1 cm thick) samples of ash/crystal mixtures under constant load. They established minimum welding temperatures between 600 and 700^oC under loads of 0.7 MPa (˜40 m of ignimbrite) to 3.6 MPa (˜250 m depth of ignimbrite). However, these data are neither sufficiently comprehensive nor coherent enough to fully describe the rheology of pyroclastic mixtures. In addition, previous studies did not examine the microstructural and geometric changes associated with welding compaction. Our goal is to provide accurate and comprehensive constitutive relationships between material properties, temperature, load and strain rate for pyroclastic material undergoing welding. Here we present results from a newly designed experimental apparatus. The experimental apparatus consists of a LoadTrac II fully automated uniaxial compression load frame manufactured by Geocomp Corporation. The load frame has a built in displacement transducer and can run both constant strain rate (10-6 to 0.25 cm/s) and constant load (up to 1150 kg) tests to a maximum displacement of 7.5 cm. The sample assembly comprises 5 cm diameter cylindrical upper and lower pistons (insulating ceramic with steel conductive ends) housed in a copper jacket. Samples are 5 cm diameter cores and can vary in length from 1 to 15 cm depending on experimental needs. A fiber insulated tube furnace capable of reaching temperatures ≈1000^oC surrounds the sample assembly. Temperature is measured using a thermocouple located inside the sample through the bottom piston; the furnace controller is capable of maintaining temperature fluctuations to <5^oC. Deformation experiments are performed on pre-fabricated cylinders of soda-lime glass beads and rhyolitic volcanic ash, as well as, cores of pumiceous rhyodacite. Experimental runs use strain rates of 10-4 and 10-5 cm/s and loads of ˜0 to 4.5 MPa. Experiments are run at temperatures between 400 and 850^oC corresponding to below and above the calorimetric glass transition temperatures of the respective materials. Data deriving from constant load and constant strain rate experiments are being used to constrain rheological models for welding of pyroclastic material.

Friction measurements in piston-cylinder apparatus using quartz-coesite reversible transition

NASA Technical Reports Server (NTRS)

Akella, J.

1979-01-01

The value of friction determined by monitoring piston displacement as a function of nominal pressure on compression and decompression cycles at 1273 K is compared with the friction value obtained by reversing the quartz-coesite transition at 1273 and 1073 K in a talc-glass-alsimag cell (Akella and Kennedy, 1971) and a low-friction salt cell (Mirwald et al., 1975). Quenching runs at 1273 K gave double values of friction of 0.25 GPa for the talc-glass-alsimag cell and 0.03 GPa for the salt cell. The piston-displacement technique gave somewhat higher values. Use of piston-displacement hysteresis loops in evaluating the actual pressure on a sample may lead to overestimates for decompression runs and underestimates for compression runs.

Quantifying grain shape with MorpheoLV: A case study using Holocene glacial marine sediments

NASA Astrophysics Data System (ADS)

Charpentier, Isabelle; Staszyc, Alicia B.; Wellner, Julia S.; Alejandro, Vanessa

2017-06-01

As demonstrated in earlier works, quantitative grain shape analysis has revealed to be a strong proxy for determining sediment transport history and depositional environments. MorpheoLV, devoted to the calculation of roughness coefficients from pictures of unique clastic sediment grains using Fourier analysis, drives computations for a collection of samples of grain images. This process may be applied to sedimentary deposits assuming core/interval/image archives for the storage of samples collected along depth. This study uses a 25.8 m jumbo piston core, NBP1203 JPC36, taken from a 100 m thick sedimentary drift deposit from Perseverance Drift on the northern Antarctic Peninsula continental shelf. Changes in ocean and ice conditions throughout the Holocene recorded in this sedimentary archive can be assessed by studying grain shape, grain texture, and other proxies. Ninety six intervals were sampled and a total of 2319 individual particle images were used. Microtextures of individual grains observed by SEM show a very high abundance of authigenically precipitated silica that obscures the original grain shape. Grain roughness, computed along depth with MorpheoLV, only shows small variation confirming the qualitative observation deduced from the SEM. Despite this, trends can be seen confirming the reliability of MorpheoLV as a tool for quantitative grain shape analysis.

Research on measurement of aviation magneto ignition strength and balance

NASA Astrophysics Data System (ADS)

Gao, Feng; He, Zhixiang; Zhang, Dingpeng

2017-12-01

Aviation magneto ignition system failure accounted for two-thirds of the total fault aviation piston engine and above. At present the method used for this failure diagnosis is often depended on the visual inspections in the civil aviation maintenance field. Due to human factors, the visual inspections cannot provide ignition intensity value and ignition equilibrium deviation value among the different spark plugs in the different cylinder of aviation piston engine. So air magneto ignition strength and balance testing has become an aviation piston engine maintenance technical problem needed to resolve. In this paper, the ultraviolet sensor with detection wavelength of 185~260nm and driving voltage of 320V DC is used as the core of ultraviolet detection to detect the ignition intensity of Aviation magneto ignition system and the balance deviation of the ignition intensity of each cylinder. The experimental results show that the rotational speed within the range 0 to 3500 RPM test error less than 0.34%, ignition strength analysis and calculation error is less than 0.13%, and measured the visual inspection is hard to distinguish between high voltage wire leakage failure of deviation value of 200 pulse ignition strength balance/Sec. The method to detect aviation piston engine maintenance of magneto ignition system fault has a certain reference value.

Accuracy of MRI-compatible contrast media injectors.

PubMed

Saake, M; Wuest, W; Becker, S; Uder, M; Janka, R

2014-03-01

To analyze the exactness of MRI-compatible contrast media (CM) injectors in an experimental setup and clinical use. Ejected fluid volumes and amounts of CM were quantified for single and double piston injections. The focus was on small volumes, as used in pediatric examination and test-bolus measurements. Samples were collected before and after clinical MRI scans and amounts of CM were measured. For single piston injections the volume differences were minimal (mean difference 0.01  ml). For double piston injections the volume of the first injection was decreased (mean 20.74  ml, target 21.00  ml, p < 0.01). After a position change of the Y-piece of the injection system, the amount of CM differed significantly from the target value (mean 1.23  mmol and 0.83  mmol at 1  ml/s flow rate, target 1.00  mmol, p < 0.01), independently of the wait time. The clinical samples confirmed these findings. The pistons of modern CM injectors work exactly. However, for small CM volumes the injected amount of CM can differ significantly from the target value in both directions. Influence factors are an incomplete elimination of air and exchange processes between the CM and saline chaser in the injection system. • In MRI examinations of children and test-bolus measurements, small amounts of CM are used. • The accuracy of single piston injections is high. • In double piston injections the injected amount of CM can differ significantly from the target value. © Georg Thieme Verlag KG Stuttgart · New York.

Percussive Force Magnitude in Permafrost

NASA Technical Reports Server (NTRS)

Eustes, A. W., III; Bridgford, E.; Tischler, A.; Wilcox, B. H.

2000-01-01

An in-depth look at percussive drilling shows that the transmission efficiency is very important; however, data for percussive drilling in hard rock or permafrost is rarely available or the existing data are very old. Transmission efficiency can be used as a measurement of the transmission of the energy in the piston to the drill steel or bit and from the bit to the rock. Having a plane and centralized impact of the piston on the drill steel can optimize the transmission efficiency from the piston to the drill steel. A transmission efficiency of near 100% between piston and drill steel is possible. The transmission efficiency between bit and rock is dependent upon the interaction within the entire system. The main factors influencing this transmission efficiency are the contact area between cutting structure and surrounding rock (energy loss due to friction heat), damping characteristics of the surrounding rock (energy dampening), and cuttings transport. Some of these parameters are not controllable. To solve the existing void regarding available drilling data, an experiment for gathering energy data in permafrost for percussive drilling was designed. Fifteen artificial permafrost samples were prepared. The samples differed in the grain size distribution to observe a possible influence of the grain size distribution on the drilling performance. The samples were then manually penetrated (with a sledge-hammer) with two different spikes.

Shipboard magnetic field "noise" reveals shallow heavy mineral sediment concentrations in Chesapeake Bay

USGS Publications Warehouse

Shah, Anjana K.; Vogt, Peter R.; Rosenbaum, Joseph G.; Newell, Wayne L.; Cronin, Thomas M.; Willard, Debra A.; Hagen, Rick A.; Brozena, John; Hofstra, Albert

2012-01-01

Shipboard magnetic field data collected over Chesapeake Bay exhibit low-amplitude, short-wavelength anomalies that most likely indicate shallow concentrations of heavy mineral sediments. Piston core layers and black sand beach samples exhibit enhanced magnetic susceptibilities and carry remanent magnetization, with mineralogical analyses indicating ilmenite and trace magnetite and/or maghemite and hematite. The anomalies are subtle and would be filtered as noise using traditional approaches, but can instead be highlighted using spectral methods, thus providing nearly continuous coverage along survey tracks. The distribution of the anomalies provides constraints on relevant sorting mechanisms. Comparisons to sonar data and previous grab samples show that two of three areas surveyed exhibit short-wavelength anomalies that are clustered over sand-covered areas, suggesting initial sorting through settling mechanisms. This is supported by a correlation between core magnetic susceptibility and grain size. Near the Choptank River, where sediment resuspension is wave-dominated, anomalies show a sharp decrease with seafloor depth that cannot be explained by signal attenuation alone. In Pocomoke Sound, where both tidal currents and wave-action impact sediment resuspension, anomalies show a more gradual decrease with depth. Near the mouth of the bay, where there is a higher influx of sediments from the continental shelf, short-wavelength anomalies are isolated and do not appear to represent heavy mineral sand concentrations. These combined observations suggest the importance of further sorting by erosional processes in certain parts of the bay. Additionally, comparisons of these data to cores sampling pre-Holocene sediments suggest that the sorting of heavy minerals in higher energy, shallow water environments provides a mechanism for correlations between core magnetic susceptibility and sea-level changes.

Apparatus for establishing flow of a fluid mass having a known velocity

NASA Technical Reports Server (NTRS)

Price, P.; Veikins, O.; Bate, E. R., Jr.; Jones, R. H. (Inventor)

1974-01-01

An apparatus for establishing a flow of fluid mass, such as gas, having a known velocity is introduced. The apparatus is characterized by an hermetically sealed chamber conforming to a closed-loop configuration and including a throat and a plurality of axially displaceable pistons for sweeping through the throat a stream of gas including a core and an unsheared boundary layer. Within the throat there is a cylindrical coring body concentrically related to the throat for receiving the core, and a chamber surrounding the cylindrical body for drawing off the boundary layer, whereby the velocity of the core is liberated from the effects of the velocity of the boundary layer.

A 400-year phytolith-based reconstruction of wild rice (Zizania palustris) abundance from Mud Lake core sediments, Fond du Lac Band of Lake Superior Chippewa Reservation, Minnesota, USA.

NASA Astrophysics Data System (ADS)

Munoz, R.; Caylor, E.; Yost, C. L.; Drake, C.; Ladwig, J. L.; Myrbo, A.; Howes, T.

2014-12-01

Wild rice (Zizania palustris L.) is an aquatic grass with spiritual and subsistence significance to Native people of the Great Lakes region of North America. Mud Lake (Mashkiigwaagamaag), located on the Fond du Lac Band of Lake Superior Chippewa Reservation in Carlton County, Minnesota, USA, once supported an extensive population of wild rice (manoomin). However, early 20th century attempts to ditch and drain surrounding wetlands for landuse intensification severely altered the natural hydrological system that supports wild rice. Fond du Lac Resource Management (FDLRM) technicians are currently working to increase the wild rice population in Mud Lake. As part of these efforts, this phytolith study was undertaken to better understand how wild rice abundance has fluctuated over the past 400 years, with particular emphasis on the 19th and 20th centuries. Phytoliths are microscopic opal silica plant remains that are incorporated into soils and lake sediments after the plant-parts that contain them decay. Wild rice produces phytolith morphotypes that are unequivocally diagnostic. Mud Lake core MNMN-MUD11-1C-1P-1 (46°43'38.39"N, 92°42'2.45"W) was piston cored by LacCore (National Lacustrine Core Facility) and FDLRM technicians on 24 May 2011. Initial core descriptions, multi-sensor core logging, phytolith sampling and phytolith extractions were completed during the summer of 2014 at LacCore. Wild rice phytolith identification and quantification was conducted on twelve samples using brightfield microscopy at 400x magnification. Wild rice phytolith concentration values ranged from 68 to 2,300 phytoliths/cm3. Wild rice accumulation rates ranged from 9 to 383 phytoliths/ cm2/yr, peaking in 1952 AD. Wild rice abundance in Mud Lake appears to be influenced by a complex set of variables that include anthropogenic disturbance, climatic events and aquatic plant community succession.

Optical free piston cell with constant diameter for use under high pressure

NASA Astrophysics Data System (ADS)

Ishihara, Koji; Takagi, Masahiro

1994-02-01

An optical free piston cell (a modified le Noble and Schlott type optical cell) is described for use in spectrophotometric study under high pressure. The cell consists of a disk, a cylinder, and a free piston, which are made of quartz and are mounted within a stainless-steel holder. A small amount of sample solution (˜0.6 cm3), which only contacts with quartz, is required for measurements. The path length is fixed (1.2 cm) at ambient pressure, but is self-adjusting at elevated pressure so that no compressibility corrections are necessary.

Researches on the Piston Ring

NASA Technical Reports Server (NTRS)

Ehihara, Keikiti

1944-01-01

In internal combustion engines, steam engines, air compressors, and so forth, the piston ring plays an important role. Especially, the recent development of Diesel engines which require a high compression pressure for their working, makes, nowadays, the packing action of the piston ring far more important than ever. Though a number of papers have been published in regard to researches on the problem of the piston ring, none has yet dealt with an exact measurement of pressure exerted on the cylinder wall at any given point of the ring. The only paper that can be traced on this subject so far is Mr. Nakagawa's report on the determination of the relative distribution of pressure on the cylinder wall, but the measuring method adopted therein appears to need further consideration. No exact idea has yet been obtained as to how the obturation of gas between the piston and cylinder, the frictional resistance of the piston, and the wear of the cylinder wall are affected by the intensity and the distribution of the radial pressure of the piston ring. Consequently, the author has endeavored, by employing an apparatus of his own invention, to get an exact determination of the pressure distribution of the piston ring. By means of a newly devised ring tester, to which piezoelectricity of quartz was applied, the distribution of the radial pressure of many sample rings on the market was accurately determined. Since many famous piston rings show very irregular pressure distribution, the author investigated and achieved a manufacturing process of the piston ring which will exert uniform pressure on the cylinder wall. Temperature effects on the configuration and on the mean spring power have also been studied. Further, the tests were performed to ascertain how the gas tightness of the piston ring may be affected by the number or spring power. The researches as to the frictional resistance between the piston ring and the cylinder wall were carried out, too. The procedure of study, and experiments conducted by the author, on this subject will be fully described in the following paragraphs.

Historical ecology of the northern Adriatic Sea: Field methods and coring device

NASA Astrophysics Data System (ADS)

Haselmair, Alexandra; Gallmetzer, Ivo; Tomasovych, Adam; Stachowitsch, Michael; Zuschin, Martin

2014-05-01

For an ongoing study on the historical ecology of the northern Adriatic Sea, the objective was to retrieve a high number of sediment cores at seven sampling stations spread across the entire basin. One set of cores is intended for sediment analyses including radiometric Pb-sediment-dating, grain size, TOC, TAC and heavy metal analyses. The other set of cores delivered enough shelly remains of endo- or epibenthic hard part producers (e.g. molluscs, crustaceans, echinoderms) to enable the reconstruction of death assemblages in core layers from top to bottom. The down-core changes of such assemblages record ecological shifts in a marine environment that has endured strong human impacts over several centuries. A 1.5 m-long core could, according to the available sedimentation data for the area, cover up to 2000 or even more years of ecological history. The coring method had to meet the following requirements: a) deliver 1.5-m-long cores from different sediment settings (mud to sand, reflecting a wide range of benthic habitats in the northern Adriatic); b) enable quick and easy deployment to ensure that multiple cores can be taken at the individual sampling stations within a short time; c) be relatively affordable and allow handling by the researchers themselves, potentially using a small vessel in order to further contain the operating costs. Two types of UWITEC™ piston corers were used to meet these requirements. A model with 90 mm of diameter (samples for sediment analysis) and another one with 160 mm, specifically designed to obtain the large amount of material needed for shell analysis, successfully delivered a total of 54 cores. The device consists of a stabilizing tripod and the interchangeable coring cylinders. It is equipped with a so-called hammer action that makes it possible, at least for the smaller cylinder, to penetrate even harder sediments. A closing mechanism of the corer retains the sediment in the cylinder upon extraction; it works either automatically through hydraulic pressure once the final core-length is reached, or can be triggered manually anytime from the surface using a connected hose and water pump. The whole coring device weighs less than 300 kg and can readily be transported in a van. It can easily be assembled, disassembled and operated by two to three persons after a brief training. With a newly designed, very simple and effective slicing device, the cores can be sliced in an upright position directly on board after extraction. This type of corer can be highly recommended for any smaller coring operations on lakes, streams, or at sea.

Impact of drag reducing polymers on the onset of instability in a pipe with reverse flow

NASA Astrophysics Data System (ADS)

Shashank, H. J.; Sreenivas, K. R.

2014-11-01

The objective of this study is to understand the mechanism by which drag reducing polymer (DRP) additives modify turbulent flow, so as to reduce turbulent drag. Reverse flow in a pipe occurs when the fluid close to the wall moves in an opposite direction to that of the core fluid. Reverse flow is established by using a piston-cylinder mechanism, the programmed motion of which imparts a known impulse to the fluid. When the piston is stopped at the end of the stroke, fluid inertia makes the core of the flow to continue in the same direction. In order to conserve mass, reverse flow is established close to the wall. An inflection point is thus formed, leading to flow instability above a critical Reynolds number. Dye and streak flow visualization experiments are performed to highlight the impact of DRP additives (polyethylene oxide, PEO, dissolved in water). The time of onset of the instability and the wavelength of the observed instability are studied in systems with and without DRP additives. This study will provide further insight into the phenomenon of turbulent polymer drag reduction.

Asbestos exposure from the overhaul of a Pratt & Whitney R2800 engine.

PubMed

Mlynarek, S P; Van Orden, D R

2012-11-01

This study assessed the asbestos exposures of airplane piston engine mechanics while performing overhaul work on a Pratt & Whitney R2800 radial engine, with tools and practices in use since the time these engines were manufactured. Approximately 40% of the bulk samples collected during this test were found to contain chrysotile. Air samples were collected during the overhaul and were analyzed by phase contrast microscopy (PCM) and transmission electron microscopy (TEM). The average worker exposure during disassembly was 0.0272f/ml (PCM) and ranged from 0.0013 to 0.1240f/ml (PCM) during an average sample collection time of 188min. The average worker exposure during reassembly was 0.0198f/ml (PCM) and ranged from 0.0055 to 0.0913f/ml (PCM) during an average sample collection time of 222min. Only one worker sample (during reassembly) was found to contain asbestos at a concentration of 0.0012f/ml (PCME). Similar results should be found in other aircraft piston engines that use metal clad and non-friable asbestos gaskets, which are the current standard in aircraft piston engines. Copyright © 2012 Elsevier Inc. All rights reserved.

Sedimentology of cores recovered from the Canada Basin of the Arctic Ocean

NASA Astrophysics Data System (ADS)

Edwards, B. D.; Saint-Ange, F.; Pohlman, J.; Higgins, J.; Mosher, D. C.; Lorenson, T. D.; Hart, P.

2011-12-01

Researchers from the United States and Canada are collaborating to understand the tectonic and sedimentary history of the Arctic Ocean between Canada and Alaska. As part of this on-going study, a joint US-Canadian ice breaker expedition operated in parts of the Canada Basin during August 2010. Occasional interruptions of the seismic data acquisition provided the ship time to collect gravity and piston cores at five sites-of-opportunity throughout the basin. High-resolution multibeam bathymetry and chirp sub-bottom profiler data collected immediately prior to coring reveal the fine-scale morphology of each site. Core photographs, X-ray radiographs, and physical property data support the following descriptions. Two piston cores were collected from the Beaufort Sea continental margin in a region of known bottom simulating reflectors (BSRs). Site 1 (2538 m water depth): This core recovered 5.72 m of gas-charged, gray sticky clay and silty-clay from an approximately 1100 m diameter, 130 m high conical mound overlying the crest of a buried anticline. Gas hydrate recovered in the core catcher combined with cracks and voids, methane and other hydrocarbon gasses, pyrite concretions, chemosynthetic clams, carbonate nodules, and soft carbonate masses indicate the likely upward migration of deep-seated fluids. Site 2 (1157 m water depth): This core, positioned 40 km upslope from the gas hydrate core, recovered 3 m of gray sticky silty clay and clayey silt near the base of an erosional scarp. Some voids and fracturing are apparent but carbonate masses and pyrite concretions are absent. Site 3 (3070 m water depth): This core from the top of a seamount discovered in 2009 in the north-central part of the Canada Basin recovered 4.94 m of sediment. More than 3 m of dark brown to yellowish brown, massive interbedded silty clays with sands and matrix-supported gravels (ice rafted debris [IRD]) occur in abrupt contact with underlying reddish yellow to brownish yellow silty clay and gravelly sandy clay interpreted to be altered hydrothermally. Successions of IRD layers create a thinly- to medium-bedded sequence throughout the lower section. Site 4 (3700 m water depth; central Canada Basin): This core recovered 3.4 m of sediment typified by decimeter-thick sequences of stacked graded beds with erosional basal contacts (Bouma sequences) characteristic of turbidite deposition. Site 5 (2081 m water depth; continental slope west of the Canadian archipelago): This core recovered 4.96 m of sediment of which the upper 2 m is silty clay to clayey silt with dispersed sand and granules. This upper section has an irregular, sharp basal contact with an underlying 16-cm-thick clast-supported massive gravel. The gravel has a scoured basal contact and overlies a monotonous gray clayey silt containing dispersed granules of IRD. Sparse and poorly preserved fauna throughout all the cores make age determination difficult; however, given the paucity of sediment cores in the Arctic Ocean, these samples provide vital geophysical groundtruth and sedimentological information about the basin.

Void Management in MEPHISTO and Other Space Experiments

NASA Technical Reports Server (NTRS)

deGroh, Henry C., III; Johnston, J. Christopher; Wei, Bingbo

1998-01-01

The second flight of NASA's Shuttle Flight experiment program known as MEPHISTO suffered from a void in the liquid portion of the sample, even though a piston arrangement was in place to keep the ampoule filled. In preparations for the next flight of the MEPHISTO furnace an animated computer program, called MEPHISTO Volume Visualizer (MVV), was written to help avoid the formation of unwanted voids. A piston system on MEPHISTO has the ability to move approximately 5 mm in compression, to accommodate expansion of the solid during heating; then from the completely compressed position, the piston can move up to 25 mm in towards the sample, effectively making the ampoule smaller and hopefully eliminating any voids. Due to the nature of the piston design and ampoule and sample arrangement, the piston has gotten stuck during normal directional solidification; this creates the risk of a void. To eliminate such a void, the liquid in the hot zones of the furnace can be heated, thereby expanding the liquid and consuming any void. The problem with this approach is that if the liquid is heated too much an overpressure could result, breaking the ampoule and ending the experiment catastrophically. The MVV has been found to be a useful tool in the assessment of the risks associated with the formation of a void and the additional heating of the liquid in the hot zone of this Bridgman type furnace. The MVV software will be discussed and copies available; it is written in the Delphi 2 programming language and runs under Windows 95 and NT. The strategies used in other flight experiments, such as the Isothermal Dendritic Growth Experiment, will also be presented.

Electrical Conductivity of Partially Molten Peridotite Analogue Under Shear: Supporting Evidence to the Partial Melting Hypothesis for the Oceanic Plate Motion

NASA Astrophysics Data System (ADS)

Manthilake, G.; Matsuzaki, T.; Yoshino, T.; Yamazaki, D.; Yoneda, A.; Ito, E.; Katsura, T.

2008-12-01

So far, two hypotheses have been proposed to explain softening of the oceanic asthenosphere allowing smooth motion of the oceanic lithosphere. One is partial melting, and the other is hydraulitic weakening. Although the hydraulitic weakening hypothesis is popular recently, Yoshino et al. [2006] suggested that this hypothesis cannot explain the high and anisotropic conductivity at the top of the asthenosphere near East Pacific Rise observed by Evans et al. [2005]. In order to explain the conductivity anisotropy over one order of magnitude by the partial melting hypothesis, we measured conductivity of partially molten peridotite analogue under shear conditions. The measured samples were mixtures of forsterite and chemically simplified basalt. The samples were pre- synthesized using a piston-cylinder apparatus at 1600 K and 2 GPa to obtain textural equilibrium. The pre- synthesized samples were formed to a disk with 3 mm in diameter and 1 mm in thickness. Conductivity measurement was carried out also at 1600 K and 2 GPa in a cubic-anvil apparatus with an additional uniaxial piston. The sample was sandwiched by two alumina pistons whose top was cut to 45 degree slope to generate shear. The shear strain rates of the sample were calibrated using a Mo strain marker in separate runs. The lower alumina piston was pushed by a tungsten carbide piston embedded in a bottom anvil with a constant speed. Conductivity was measured in the directions normal and parallel to the shear direction simultaneously. We mainly studied the sample with 1.6 volume percent of basaltic component. The shear strain rates were 0, 1.2x10(-6) and 5.2x10(-6) /s. The sample without shear did not show conductivity anisotropy. In contrast, the samples with shear showed one order of magnitude higher conductivity in the direction parallel to the shear than that normal to the shear. After the total strains reached 0.3, the magnitude of anisotropy became almost constant for both of the strain rates. The magnitude is thus independent of the strain rate. This study demonstrates that the anisotropy at the top of the asthenosphere can be explained based on the partially molten asthenosphere sheared by the plate motion.

Results of NanTroSEIZE Expeditions Stages 1 & 2: Deep-sea Coring Operations on-board the Deep-sea Drilling Vessel Chikyu and Development of Coring Equipment for Stage 3

NASA Astrophysics Data System (ADS)

Shinmoto, Y.; Wada, K.; Miyazaki, E.; Sanada, Y.; Sawada, I.; Yamao, M.

2010-12-01

The Nankai-Trough Seismogenic Zone Experiment (NanTroSEIZE) has carried out several drilling expeditions in the Kumano Basin off the Kii-Peninsula of Japan with the deep-sea scientific drilling vessel Chikyu. Core sampling runs were carried out during the expeditions using an advanced multiple wireline coring system which can continuously core into sections of undersea formations. The core recovery rate with the Rotary Core Barrel (RCB) system was rather low as compared with other methods such as the Hydraulic Piston Coring System (HPCS) and Extended Shoe Coring System (ESCS). Drilling conditions such as hole collapse and sea conditions such as high ship-heave motions need to be analyzed along with differences in lithology, formation hardness, water depth and coring depth in order to develop coring tools, such as the core barrel or core bit, that will yield the highest core recovery and quality. The core bit is especially important in good recovery of high quality cores, however, the PDC cutters were severely damaged during the NanTroSEIZE Stages 1 & 2 expeditions due to severe drilling conditions. In the Stage 1 (riserless coring) the average core recovery was rather low at 38 % with the RCB and many difficulties such as borehole collapse, stick-slip and stuck pipe occurred, causing the damage of several of the PDC cutters. In Stage 2, a new design for the core bit was deployed and core recovery was improved at 67 % for the riserless system and 85 % with the riser. However, due to harsh drilling conditions, the PDC core bit and all of the PDC cutters were completely worn down. Another original core bit was also deployed, however, core recovery performance was low even for plate boundary core samples. This study aims to identify the influence of the RCB system specifically on the recovery rates at each of the holes drilled in the NanTroSEIZE coring expeditions. The drilling parameters such as weight-on-bit, torque, rotary speed and flow rate, etc., were analyzed and conditions such as formation, tools, and sea conditions which directly affect core recovery have been categorized. Also discussed will be the further development of such coring equipment as the core bit and core barrel for the NanTroSEIZE Stage 3 expeditions, which aim to reach a depth of 7000 m-below the sea floor into harder formations under extreme drilling conditions.

87Sr/86Sr dating and preliminary interpretation of magnetic susceptibility logs of giant piston cores from the Rio Grande Rise in the South Atlantic

NASA Astrophysics Data System (ADS)

Lacasse, Christian Michel; Santos, Roberto Ventura; Dantas, Elton Luiz; Vigneron, Quentin; de Sousa, Isabela Moreno Cordeiro; Harlamov, Vadim; Lisniowski, Maria Aline; Pessanha, Ivo Bruno Machado; Frazão, Eugênio Pires; Cavalcanti, José Adilson Dias

2017-12-01

Giant piston cores recovered from shallow depths (<1200 mbsl) on the northern flank of the Rio Grande Rise, bathed today in intermediate waters (AAIW, UCDW), have uncovered new stratigraphic and paleoceanographic aspects of the Plio-Pleistocene in the South Atlantic. Based on strontium isotope analysis of well-preserved foraminifera-rich sediment a stratigraphy was developed from lowess curve fitting of the data and an optimized matching with an internationally recognized timescale of 87Sr/86Sr seawater variation through geological times. Depth-to-age conversion of the magnetic susceptibility logs was implemented based on the identification of correlative peaks between cores and the developed 87Sr/86Sr age model. The influence of Northern Hemisphere glaciation is reflected in these new stratigraphic logs by a gradual increase from ∼2.7 Ma in the lower signal of magnetic susceptibility (below background level), to values approaching the arithmetic means, likely reflecting an overall increase in terrigenous input. The Rio Grande Rise cores have very low Plio-Pleistocene sedimentation rates (∼0.4-0.8 cm/ka), similar to gravity cores from the oligotrophic subtropical South Atlantic (below ∼2000 mbsl), and for which an inverse correlation between carbonate content and magnetic susceptibility was established. The coring depths on the Rio Grande Rise encompass strong gradients in oxygen concentration and other seawater parameters that define today's AAIW/UCDW transition. Depth-dependent variation in sedimentation rates since the onset of Northern Hemisphere glaciation coincides with the incursion of intermediate waters (UCDW, AAIW) in response to the overall reduction of NADW export to the Southern Ocean. Background levels of magnetic susceptibility in the cores suggest that this variation is mainly attributed to terrigenous input. The source region of this material has yet to be traced by considering in particular the mineral composition and paramagnetic properties of the detrital clays.

Active hexagonally segmented mirror to investigate new optical phasing technologies for segmented telescopes.

PubMed

Gonté, Frédéric; Dupuy, Christophe; Luong, Bruno; Frank, Christoph; Brast, Roland; Sedghi, Baback

2009-11-10

The primary mirror of the future European Extremely Large Telescope will be equipped with 984 hexagonal segments. The alignment of the segments in piston, tip, and tilt within a few nanometers requires an optical phasing sensor. A test bench has been designed to study four different optical phasing sensor technologies. The core element of the test bench is an active segmented mirror composed of 61 flat hexagonal segments with a size of 17 mm side to side. Each of them can be controlled in piston, tip, and tilt by three piezoactuators with a precision better than 1 nm. The context of this development, the requirements, the design, and the integration of this system are explained. The first results on the final precision obtained in closed-loop control are also presented.

EN AW-4032 T6 Piston Alloy After High-Temperature Exposure: Residual Strength and Microstructural Features

NASA Astrophysics Data System (ADS)

Balducci, Eleonora; Ceschini, Lorella; Morri, Alessandro; Morri, Andrea

2017-08-01

This study aims to evaluate the effects of prolonged thermal exposure on both microstructural evolution and mechanical properties of the EN AW-4032 T6 piston alloy. For the purpose, the experimental activities have been carried out on samples machined from forged and heat-treated automotive pistons. The effects of overaging have been investigated in the temperature range of 140-290 °C, firstly by evaluating the time-temperature-hardness curves and then by carrying out room-temperature tensile tests on overaged samples. The material softening was substantial and extremely rapid when the soaking temperature exceeded 250 °C. During overaging, both the tensile strength and the residual hardness considerably decreased, and a relationship between these parameters has been established. The alloy behavior in the plastic field has been modeled according to the Hollomon's equation, showing that both the strain hardening exponent and the strength coefficient are a function of the residual hardness. The results were finally related to the corresponding microstructural changes: OM and FEG-SEM metallographic and fractographic analyses on overaged samples gave evidence of coarsened precipitates along the grain boundaries.

End-Pleistocene to Holocene paleoenvironmental record from piston corer samples and the challenge of stratigraphic correlation of playa sediment data with a connected alluvial apron from Damghan Basin, Iran

NASA Astrophysics Data System (ADS)

Büdel, Christian; Hoelzmann, Philipp; Wennrich, Volker; Majid Padashi, Sajed; Baumhauer, Roland

2015-04-01

The study yields a first characterization and correlation of the end-Pleistocene to Holocene sediment archive of playa and playa lake deposits in the Damghan Basin, northern Iran. The Basin sediments are deposited since Mio- and Pliocene, which is valid for the connected alluvial fans, too. These are covering the area between the playa and mountains and while prograding from the mountain ranges they deliver gravels and fine-sediments to the basins sink. The processes on the studied alluvial apron are described and dated already and can be explained in seven morphodynamic phases, which are linked to a general lake level high-stand in north-east Iran at about 8000-9000 years ago. If and how these phases are passed on from the alluvial record down to the playa sediment record is aim of this study. Today the salt pans margins are highly affected by salt tectonic drifting and access was suboptimal. Only here drilling could be performed through about 280 centimeters of salt-crust unfrequently intercalated with loamy layers. For yielding undisturbed playa sediment records sampling was performed with inliner-tubes deployed in a piston corer (Kullenberg type). Thus at two different drilling sites in summation seven cores could be taken, down to a maximum depth of 129 cm and 1000 cm. Back in Germany the cores had been opened and initially described, photographed and optically scanned with a core logger. Regarding future studies, the aim was a best possible comprehensive documentation of the cores. Therefore basically grainsize measurements (laser diffraction), multi element analyses (XRF, ICP-OES, titrimetry) and mineralogical measurements (XRD) had been deployed on samples taken from every single previously identified layer. Continuous elemental data was secured by use of a XRF-scanning core logger. The sedimentological description together with laboratory element analyses shows saline conditions in the first three meters coincide with general coarser grain sizes. The next three meters are made up by homogenous partly laminated deposits, rich auf clay and silt and with a decreased content of sulphur and halite. Regular Peaks of sulfate and calcium within this unit presumably indicate post-sedimentary precipitation of gypsum. The homogenous sediment unit is followed by layers clearly set up in three major phases of up-fining sediments. Higher Al and Mg contents following this sedimentation phases suggest a considerable amount of syn-sedimentary clay mineral enrichment. The alignment of alluvial fan phases and phases recorded in the playa is challenging. As figured out before, the focused signals in the study are linked to non-local factors affecting supra-regional land surface alteration. But 0 to less than 1 % organic carbon contents decrease the chance of deriving a valid sediment dating and the possibility of chrono-stratigraphic correlation. Anyway, the clear transitional zone from halite dominated to more or less halite-free sediments can serve as a guideline to the development of further correlations.

Pore-water extraction from unsaturated tuff by triaxial and one-dimensional compression methods, Nevada Test Site, Nevada

USGS Publications Warehouse

Mower, Timothy E.; Higgins, Jerry D.; Yang, In C.; Peters, Charles A.

1994-01-01

Study of the hydrologic system at Yucca Mountain, Nevada, requires the extraction of pore-water samples from welded and nonwelded, unsaturated tuffs. Two compression methods (triaxial compression and one-dimensional compression) were examined to develop a repeatable extraction technique and to investigate the effects of the extraction method on the original pore-fluid composition. A commercially available triaxial cell was modified to collect pore water expelled from tuff cores. The triaxial cell applied a maximum axial stress of 193 MPa and a maximum confining stress of 68 MPa. Results obtained from triaxial compression testing indicated that pore-water samples could be obtained from nonwelded tuff cores that had initial moisture contents as small as 13 percent (by weight of dry soil). Injection of nitrogen gas while the test core was held at the maximum axial stress caused expulsion of additional pore water and reduced the required initial moisture content from 13 to 11 percent. Experimental calculations, together with experience gained from testing moderately welded tuff cores, indicated that the triaxial cell used in this study could not apply adequate axial or confining stress to expel pore water from cores of densely welded tuffs. This concern led to the design, fabrication, and testing of a one-dimensional compression cell. The one-dimensional compression cell used in this study was constructed from hardened 4340-alloy and nickel-alloy steels and could apply a maximum axial stress of 552 MPa. The major components of the device include a corpus ring and sample sleeve to confine the sample, a piston and base platen to apply axial load, and drainage plates to transmit expelled water from the test core out of the cell. One-dimensional compression extracted pore water from nonwelded tuff cores that had initial moisture contents as small as 7.6 percent; pore water was expelled from densely welded tuff cores that had initial moisture contents as small as 7.7 percent. Injection of nitrogen gas at the maximum axial stress did not produce additional pore water from nonwelded tuff cores, but was critical to recovery of pore water from densely welded tuff cores. Gas injection reduced the required initial moisture content in welded tuff cores from 7.7 to 6.5 percent. Based on the mechanical ability of a pore-water extraction method to remove water from welded and nonwelded tuff cores, one-dimensional compression is a more effective extraction method than triaxial compression. However, because the effects that one-dimensional compression has on pore-water chemistry are not completely understood, additional testing will be needed to verify that this method is suitable for pore-water extraction from Yucca Mountain tuffs.

Nitrogen partitioning during core-mantle differentiation

NASA Astrophysics Data System (ADS)

Speelmanns, I. M.; Schmidt, M. W.; Liebske, C.

2016-12-01

This study investiagtes nitrogen partitioing between metal and silicate melts as relevant for core segregation during the accretion of planetesimals into the Earth. On present day Earth, N belongs to the most important elements, as it is one of the key constituents of our atmosphere and forms the basis of life. However, the geochemistry of N, i.e. its distribution and isotopic fractionation between Earth's deep reservoirs is not well constrained. In order to determine the partitioning behaviour of N, a centrifuging piston cylinder was used to euqilibrate and then gravitationally separate metal-silicate melt pairs at 1250 °C, 1 GPa over the range of oxygen fugacities thought to have prevailied druing core segreagtion (IW-4 to IW). Complete segregation of the two melts was reached within 3 hours at 1000 g, the interface showing a nice meniscus The applied double capsule technique, using an outer metallic and inner non-metallic (mostly graphite) capsule, minimizes volatile loss over the course of the experiment compared to single non-metallic capsules. The two quenched melts were cut apart, cleaned at the outside and N concentrations of the melts were analysed on bulk samples by an elemental analyser. Nevertheless, the low amount of sample material and the N yield in the high pressure experiments required the developement of new analytical routines. Despite these experimental and analytical difficulties, we were able to determine a DNmetal/silicateof 13±0.25 at IW-1, N partitioning into the core froming metal. The few availible literature data [1],[2] suggest that N changes its compatibility favoring the silicate melt or magma ocean at around IW-2.5. In order to asses how much N may effectively be contained in the core and the silicate Earth, experiments characterizing N behaviour over the entire range of core formation condtitions are well under way. [1] Kadik et al., (2011) Geochemistry International 49.5: 429-438. [2] Roskosz et al., (2013) GCA 121: 15-28.

A Brunhes-Matuyama polarity transition record from anoxic sediments in the South Atlantic (Ocean Drilling Program Hole 1082C)

NASA Astrophysics Data System (ADS)

Yamazaki, T.; Oda, H.

2001-08-01

A paleomagnetic study was performed on Hole 1082C sediment cores taken during the Ocean Drilling Program (ODP) Leg 175 in the South Atlantic in order to obtain a high-resolution Brunhes-Matuyama (B/M) polarity transition record. An average sedimentation rate was as high as 10 cm/kyr. The cores consist of strongly anoxic sediments, which is common for the areas of large material supply. Anoxic sediments, which are geochemically quite active, were considered to be unsuitable for studies on detailed behavior of the geomagnetic field such as polarity transitions. For global site distribution, however, it is necessary to make efforts to retrieve paleomagnetic records from such sediments. A continuous record of directional changes around the transition was obtained from U-channel samples after cleaning by stepwise alternating-field (AF) demagnetization. Consistency of the record was checked using discrete samples taken from the other half of the cores. The coring-induced magnetic overprint of radial-inward direction, which has often been reported from ODP piston-cores, was negligibly small in our cores. Relative paleointensity variation was estimated from remanent intensities of the discrete samples normalized by artificial remanences. Our record shows following features of the B/M transition similar to those already reported by previous studies. A zone of large directional fluctuations with low paleointensities occurs just before the main transition (788 to 795 ka based on the oxygen-isotope stratigraphy), which would correspond to the "precursor" of Hartl and Tauxe (1996). The virtual geomagnetic poles (VGPs) at the precursor lie along the so-called preferred longitudinal bands over the north-south Americas and Australia-east Asia. After the main transition from the reversed to normal polarity, VGPs stayed in the middle-to-high latitudes over the North America with an intermediate paleointensity for about 5~kyrs, and then moved in the vicinity of the North Pole with full recovery of intensity. Such behavior was reported by Oda et al. (2000). These similarities suggest that the anoxic sediments at Site 1082 could record the behavior of the geomagnetic field rather faithfully, although the remanence may be of chemical origin.

PSV records from sediments of modern lakes (Aslikyl, Svir, Naroch).

NASA Astrophysics Data System (ADS)

Kuzina, D.; Kosareva, L.; Nourgaliev, D.; Kosarev, V.

2014-12-01

During the last 20 years, our paleomagnetic group had investigated many lakes with the aim to know the behavior of the geomagnetic field during the Holocene. Lake sediments are the good presenters of the paleosecular variation (PSV) records. In this paper are presented materials from Lakes Aslikul (Russia, 54o 25' N, 54o 07' E), Svir (Belorussia, 54o 47' N; 26o 30' E), Naroch (Belorussia, 54o 51' N, 26o 51' E). Samples of lake floor sediments were collected using a piston corer designed and manufactured at the Kazan University as a prototype were used piston corer which had been designed and used by F. J. H. Mackereth. Three cores were collected from each Lake Aslikul and Svir and six cores from Lake Naroch. Cores length was between 3,5-6,5 meters. Sediments were subsampled into cubic nonmagnetic plastic boxes. Their magnetic susceptibilities were then measured using a MS2-B instrument, and their natural remanent magnetization (NRM) (module and direction) was measured using a JR-4 magnetometer. Based on this data were built generalized record for each parameter. We compared the geomagnetic field variations recorded in our study with the records reported in the literature for the sediments in the different lakes. Our data have a good PSV records correlation with other data so we can obtain age of sediments according to PSV records. The dating of lakes sediments was also improved and further detailed by radiocarbon dating that gave the same results. Some characteristic features, the B and S minima and the Y and E maxima (cf. nomenclature of Thompson and Turner, 1982) are recognized. All peaks have a wide but complicated structure. Studied lakes compared to the other European records available, it can be concluded that the PSV master curves obtained in this study can be used to model Holocene geomagnetic variations. The work is performed according to the Russian Government Program of Competitive Growth of Kazan Federal University also by RFBR research projects No. 14-05-00785- а.

Pb isotope compositions of modern deep sea turbidites

NASA Astrophysics Data System (ADS)

Hemming, S. R.; McLennan, S. M.

2001-01-01

Modern deep sea turbidite muds and sands collected from Lamont piston cores represent a large range in age of detrital sources as well as a spectrum of tectonic settings. Pb isotope compositions of all but three of the 66 samples lie to the right of the 4.56 Ga Geochron, and most also lie along a slope consistent with a time-integrated κ ( 232Th/ 238U) between 3.8 and 4.2. Modern deep sea turbidites show a predictable negative correlation between both Pb and Sr isotope ratios and ɛNd and ɛHf, clearly related to the age of continental sources. However, the consistency between Pb and Nd isotopes breaks down for samples with very old provenance ( ɛNd<-20) that are far less radiogenic than predicted by the negative correlation. The correlations among Sr, Nd and Hf isotopes also become more scattered in samples with very old provenance. The unradiogenic Pb isotopic character of modern sediments with Archean Nd model ages is consistent with a model where Th and U abundances of the Archean upper crust are significantly lower than the post-Archean upper crust.

Characterizing ``Radio Mode'' AGN Outbursts: the Recent 12 Myr History of the Supermassive Black Hole in M87

NASA Astrophysics Data System (ADS)

Forman, William R.; Churazov, Eugene; Jones, Christine; Heinz, Sebastian; Kraft, Ralph P.; Vikhlinin, Alexey

2016-01-01

M87, the bright active galaxy dominating the core of the Virgo cluster, is ideal for studying the interaction of a supermassive black hole with a gas rich environment. We combine results from a deep Chandra observation with a simple shock model to derive the properties of the outburst that created the 13 kpc shock previously reported around M87. The principal constraints for the model are 1) the observed temperature and density profiles, 2) the measured Mach number (about 1.2) and radius of the 13 kpc shock, 3) the observed size of the inner cavity (~3 kpc) that serves as the piston to drive the shock, and 4) the absence of a hot, low density plasma surrounding the central cavity. Qualitatively, the absence of a hot, low density (shocked) region surrounding the inner radio lobes (the piston), requires a "slowly" expanding piston and "long" duration outburst rather than a Sedov-like outburst. Quantitatively, a roughly 5 x 1057 ergs outburst that began about 12 Myr ago and lasted about 2 Myr matches all the constraints. In the context of the model, ~20% of the energy is carried by the shock as it expands to large radii while ~80% of the outburst energy is available to heat the core gas. For an outburst repetition rate of about 12 Myrs (the outburst age), 80% of the outburst energy is sufficient to balance radiative cooling. We discuss the outburst history of M87 as chronicled in its radio and X-ray images and the implications of these outbursts for heating gas rich environments.

Online monitoring of cartilage tissue in a novel bioreactor

NASA Astrophysics Data System (ADS)

von der Burg, E.; von Buttlar, M.; Grill, W.

2011-04-01

Standard techniques for the analysis of biological tissues like immunohistochemical staining are typically invasive and lead to mortification of cells. Non-invasive monitoring is an important element of regenerative medicine because implants and components of implants should be 100% quality-checked with non-invasive and therefore also marker-free methods. We report on a new bioreactor for the production of collagen scaffolds seeded with Mesenchymal Stem Cells (MSCs). It contains a computer controlled mechanical activation and ultrasonic online monitoring and has been constructed for the in situ determination of ultrasonic and rheological parameters. During the cultivation period of about two weeks the scaffold is periodically compressed by two movable pistons for improved differentiation of the MSCs. This periodic compression beneficially ensures the supply with nutrition even inside the sample. During the physiological stimuli, rheological properties are measured by means of highly sensitive load cells. In addition measurements of the speed of sound in the sample and in the culture medium, with frequencies up to 16 MHz, are performed continuously. Therefore piezoceramic transducers are attached to the pistons and emit and detect ultrasonic waves, travelling through the pistons, the sample and the culture medium. The time-of-flight (TOF) of the ultrasonic signals is determined in real time with the aid of chirped excitation and correlation procedures with a resolution of at least 10 ps. The implemented ultrasonic measurement scheme allows beside the speed of sound measurements the detection of the distance between the pistons with a resolution better than 100 nm. The developed monitoring delivers information on rigidity, fluid dynamics and velocity of sound in the sample and in the culture medium. The hermetically sealed bioreactor with its life support system provides a biocompatible environment for MSCs for long time cultivation.

Age of Palos Verdes submarine debris avalanche, southern California

USGS Publications Warehouse

Normark, W.R.; McGann, M.; Sliter, R.

2004-01-01

The Palos Verdes debris avalanche is the largest, by volume, late Quaternary mass-wasted deposit recognized from the inner California Borderland basins. Early workers speculated that the sediment failure giving rise to the deposit is young, taking place well after sea level reached its present position. A newly acquired, closely-spaced grid of high-resolution, deep-tow boomer profiles of the debris avalanche shows that the Palos Verdes debris avalanche fills a turbidite leveed channel that extends seaward from San Pedro Sea Valley, with the bulk of the avalanche deposit appearing to result from a single failure on the adjacent slope. Radiocarbon dates from piston-cored sediment samples acquired near the distal edge of the avalanche deposit indicate that the main failure took place about 7500 yr BP. ?? 2003 Elsevier B.V. All rights reserved.

Piston and connecting rod assembly

NASA Technical Reports Server (NTRS)

Brogdon, James William (Inventor); Gill, David Keith (Inventor); Chatten, John K. (Inventor)

2001-01-01

A piston and connecting rod assembly includes a piston crown, a piston skirt, a connecting rod, and a bearing insert. The piston skirt is a component separate from the piston crown and is connected to the piston crown to provide a piston body. The bearing insert is a component separate from the piston crown and the piston skirt and is fixedly disposed within the piston body. A bearing surface of a connecting rod contacts the bearing insert to thereby movably associate the connecting rod and the piston body.

A multi-particle crushing apparatus for studying rock fragmentation due to repeated impacts

NASA Astrophysics Data System (ADS)

Huang, S.; Mohanty, B.; Xia, K.

2017-12-01

Rock crushing is a common process in mining and related operations. Although a number of particle crushing tests have been proposed in the literature, most of them are concerned with single-particle crushing, i.e., a single rock sample is crushed in each test. Considering the realistic scenario in crushers where many fragments are involved, a laboratory crushing apparatus is developed in this study. This device consists of a Hopkinson pressure bar system and a piston-holder system. The Hopkinson pressure bar system is used to apply calibrated dynamic loads to the piston-holder system, and the piston-holder system is used to hold rock samples and to recover fragments for subsequent particle size analysis. The rock samples are subjected to three to seven impacts under three impact velocities (2.2, 3.8, and 5.0 m/s), with the feed size of the rock particle samples limited between 9.5 and 12.7 mm. Several key parameters are determined from this test, including particle size distribution parameters, impact velocity, loading pressure, and total work. The results show that the total work correlates well with resulting fragmentation size distribution, and the apparatus provides a useful tool for studying the mechanism of crushing, which further provides guidelines for the design of commercial crushers.

Ethylene monitoring and control system

NASA Technical Reports Server (NTRS)

Nelson, Bruce N. (Inventor); Kanc, James A. (Inventor); Richard, II, Roy V. (Inventor)

2000-01-01

A system that can accurately monitor and control low concentrations of ethylene gas includes a test chamber configured to receive sample gas potentially containing an ethylene concentration and ozone, a detector configured to receive light produced during a reaction between the ethylene and ozone and to produce signals related thereto, and a computer connected to the detector to process the signals to determine therefrom a value of the concentration of ethylene in the sample gas. The supply for the system can include a four way valve configured to receive pressurized gas at one input and a test chamber. A piston is journaled in the test chamber with a drive end disposed in a drive chamber and a reaction end defining with walls of the test chamber a variable volume reaction chamber. The drive end of the piston is pneumatically connected to two ports of the four way valve to provide motive force to the piston. A manifold is connected to the variable volume reaction chamber, and is configured to receive sample gasses from at least one of a plurality of ports connectable to degreening rooms and to supply the sample gas to the reactive chamber for reaction with ozone. The apparatus can be used to monitor and control the ethylene concentration in multiple degreening rooms.

Ethylene monitoring and control system

NASA Technical Reports Server (NTRS)

Nelson, Bruce N. (Inventor); Kane, James A. (Inventor); Richard, II, Roy V. (Inventor)

2001-01-01

A system that can accurately monitor and control low concentrations of ethylene gas includes a test chamber configured to receive sample gas potentially containing an ethylene concentration and ozone, a detector configured to receive light produced during a reaction between the ethylene and ozone and to produce signals related thereto, and a computer connected to the detector to process the signals to determine therefrom a value of the concentration of ethylene in the sample gas. The supply for the system can include a four way valve configured to receive pressurized gas at one input and a test chamber. A piston is journaled in the test chamber with a drive end disposed in a drive chamber and a reaction end defining with walls of the test chamber a variable volume reaction chamber. The drive end of the piston is pneumatically connected to two ports of the four way valve to provide motive force to the piston. A manifold is connected to the variable volume reaction chamber, and is configured to receive sample gasses from at least one of a plurality of ports connectable to degreening rooms and to supply the sample gas to the reactive chamber for reaction with ozone. The apparatus can be used to monitor and control the ethylene concentration in multiple degreening rooms.

Luminescence signal profiling: a new proxy for sedimentologically "invisible" marine Mass Transport Deposits (MTDs)

NASA Astrophysics Data System (ADS)

López, Gloria I.; Bialik, Or; Waldmann, Nicolas

2017-04-01

When dealing with fine-grained, organic-rich, colour-monotone, underwater marine sediment cores retrieved from the continental shelf or slope, the initial visual impression, upon split-opening the vessels, is often of a "disappointing" homogeneous, monotonous, continuous archive. Only after thorough, micro- to macro-scale, multi-parameter investigations the sediment reveals its treasures, initially by performing some measurements on the intact core itself, hence depicting for the first time its contents, and subsequently by carrying out the destructive, multi-proxy sample-based analyses. Usually, routine Multi-Sensor Core Logger (MSCL) measurements of petrophysical parameters (e.g. magnetic susceptibility, density, P-Wave velocity) on un-split sediment cores are the first undertaken while still on-board in the field or back at the laboratory. Less often done, but equally valuable, are continuous X-Ray and CT scan imaging of the same intact archives. Upon splitting, routine granulometry, micro- and macro-fossil and invertebrate identification, total organic / inorganic carbon content (TOC / TIC), amid other analyses take place. The geochronology component is also established usually by AMS 14C on selected organic-rich units, and less common is Optically Stimulated Luminescence (OSL) dating used on the coarser-grained, siliciclastic layers. A relatively new tool used in Luminescence, the Portable OSL Reader, employed to rapidly assess the luminescence signal of untreated poly-mineral samples to assist with targeted field sampling for full OSL dating, was used for the first time in marine sediment cores as a novel petrophysical characterization tool with astonishing results. In this study, two 2 m-long underwater piston sediment cores recovered from 200 m depths on the continental shelf off-southern Israel, were subjected to pulsed-photon stimulation (PPSL) obtaining favourable luminescence signals along their entire lengths. Astoundingly, luminescence signals were obtained on both, already split-opened cores. Both cores depicted the monotonous characteristics of homogeneousness down-core as per most of the results obtained from the non-destructive and destructive tests. One of the cores showed several small higher energy events, including a Mass Transport Deposit (MTD) within its first 10 cm, only fully visible on the CT scan imaging, the PPSL profile and particle size distribution plot. This initial investigation demonstrates the feasibility and usefulness of luminescence profiling as a new sedimentological and petrophysical proxy to better visualize homogeneous yet complex, fine-grained, underwater archives. Moreover, it helps to understand the continuity of the stratigraphy and linearity of deposition of the sediment, besides assisting on the estimation of relative ages provided that good OSL ages are obtained throughout the recovered archive.

Piston core record of Late Paleogene (31 Ma) to recent seafloor hydrothermal activity in the Southwest Pacific Basin

NASA Astrophysics Data System (ADS)

Stancin, Andrea M.; Gleason, James D.; Owen, Robert M.; Rea, David K.; Blum, Joel D.

2008-03-01

A large diameter piston core containing 8.35 m of metalliferous sediment has been recovered from a small abyssal valley in the remote Southwest Pacific Basin (31° 42.194'S, 143° 30° 331'W; 5082 m water depth), providing unique insight into hydrothermal activity and eolian sedimentation there since the early Oligocene. A combination of fish-teeth Sr-isotope stratigraphy and INAA geochemical data reveals an exponentially decreasing hydrothermal flux 31 Ma to the present. Although hydrothermal sedimentation related to seafloor spreading explains this trend, a complex history of late Eocene/early Oligocene ridge jumps, propagating rifts and plate tectonic reorganization of South Pacific seafloor could have also played a role. A possible hiatus in deposition, as recorded by changes in core composition just below 2 m depth, is beyond the resolution of the fish teeth Sr isotope dating method employed here; however, the timing of this interval may be coincident with extinction of the Pacific-Farallon Ridge at ˜20 Ma. A low flux eolian component accumulating at this site shows an increase relative to the hydrothermal component above 2 m depth, consistent with dust-generating continental sources far to the west (Australia/New Zealand). This is the first long-term paleoceanographic record obtained from within the South Pacific "bare zone" (Rea et al., 2006), an anomalous region where Pacific seafloor has largely escaped sediment accumulation since the Late Cretaceous.

The HAMP Signal Relay Domain Adopts Multiple Conformational States through Collective Piston and Tilt Motions

PubMed Central

Zhu, Lizhe; Bolhuis, Peter G.; Vreede, Jocelyne

2013-01-01

The HAMP domain is a linker region in prokaryotic sensor proteins and relays input signals to the transmitter domain and vice versa. Functional as a dimer, the structure of HAMP shows a parallel coiled-coil motif comprising four helices. To date, it is unclear how HAMP can relay signals from one domain to another, although several models exist. In this work, we use molecular simulation to test the hypothesis that HAMP adopts different conformations, one of which represents an active, signal-relaying configuration, and another an inactive, resting state. We first performed molecular dynamics simulation on the prototype HAMP domain Af1503 from Archaeoglobus fulgidus. We explored its conformational space by taking the structure of the A291F mutant disabling HAMP activity as a starting point. These simulations revealed additional conformational states that differ in the tilt angles between the helices as well as the relative piston shifts of the helices relative to each other. By enhancing the sampling in a metadynamics set up, we investigated three mechanistic models for HAMP signal transduction. Our results indicate that HAMP can access additional conformational states characterized by piston motion. Furthermore, the piston motion of the N-terminal helix of one monomer is directly correlated with the opposite piston motion of the C-terminal helix of the other monomer. The change in piston motion is accompanied by a change in tilt angle between the monomers, thus revealing that HAMP exhibits a collective motion, i.e. a combination of changes in tilt angles and a piston-like displacement. Our results provide insights into the conformational changes that underlie the signaling mechanism involving HAMP. PMID:23468603

Double bowl piston

DOEpatents

Meffert, Darrel Henry; Urven, Jr., Roger Leroy; Brown, Cory Andrew; Runge, Mark Harold

2007-03-06

A piston for an internal combustion engine is disclosed. The piston has a piston crown with a face having an interior annular edge. The piston also has first piston bowl recessed within the face of the piston crown. The first piston bowl has a bottom surface and an outer wall. A line extending from the interior annular edge of the face and tangent with the outer wall forms an interior angle greater than 90 degrees with the face of the piston. The piston also has a second piston bowl that is centrally located and has an upper edge located below a face of the piston crown.

Bedrock cores from 89° North: Implications for the geologic framework and Neogene paleoceanography of Lomonosov Ridge and a tie to the Barents shelf

USGS Publications Warehouse

Grantz, Arthur; Pease, Victoria L.; Willard, Debra A.; Phillips, R.L.; Clark, David L.

2001-01-01

Two piston cores from the Eurasian flank of Lomonosov Ridge near lat 88.9°N, long 140°E provide the first samples of bedrock from this high-standing trans-Arctic ridge. Core 94-PC27 sampled nonmarine siltstone similar in facies and age to uppermost Triassic to lower Lower Jurassic and mid– Lower Cretaceous beds in the 4 to > 5 km Mesozoic section on Franz Josef Land, on the outer Barents shelf. A ca. 250 Ma peak in the cumulative frequency curve of detrital zircons from the siltstone, dated by U- Th-Pb analysis, suggests a source in the post-tectonic syenites of northern Taymyr and nearby islands in the Kara Sea. Textural trends reported in the literature indicate that the Lower Jurassic nonmarine strata of Franz Josef Land coarsen to the southeast; this suggests the existence of a sedimentary system in which detrital zircons could be transported from the northern Taymyr Peninsula to the outer Barents shelf near the position of core 94-PC27 prior to opening of the Eurasia Basin. Correlation of the coaly siltstone in core 94-PC27 with part of the Mesozoic section on Franz Josef Land is compatible with the strong evidence from seafloor magnetic anomalies and bathymetry that Lomonosov Ridge is a continental fragment rifted from the Barents shelf during the Cenozoic. It also suggests that Lomonosov Ridge near the North Pole is underlain by a substantial section of unmetamorphosed Mesozoic marine and nonmarine sedimentary strata. Core 94-PC29 sampled cyclical deposits containing ice-rafted debris (IRD) overlying weakly consolidated laminated olive-black anoxic Neogene siltstone and mudstone with an average total organic carbon (TOC) of 4.1 wt%. The high TOC content of the mudstone indicates that during the Neogene, prior to the introduction of IRD into the Arctic seas about 3.3 Ma (early late Pliocene), the shallow waters of the central Arctic Ocean supported significant primary photosynthetic organic production near the North Pole. These deposits also contain fine grains of siltstone that resemble the breccia-clast siltstone of core 94-PC27 and reworked Carboniferous, Cretaceous, and Tertiary palynomorphs that may have also originated in the bedrock of Lomonosov Ridge.

Trace Metal Variations Detected by Using Continuous XRF Core Scanning: Preliminary Results on Redox-sensitive Elements in East Sea, Korea

NASA Astrophysics Data System (ADS)

Cho, J. H.; Shin, D. H.; Kim, J. K.; Hyun, S.; Jang, S.; Kum, B. C.; Yoo, K. C.; Moh, T. J.

2017-12-01

The cruise of R/V ISABU focused on the detailed geological, geochemical and paleoceanographical investigations in the East Sea. The purpose of this cruise was the use of technically sophisticated Giant Piston Corer (GPC, OSIL) as well as the recovery of the longest piston core (20.7 m, ISA-16ESUB-2B) ever recorded in KIOST with a high resolution of stratigraphic sedimentary layer. The Late Pleistocene to the Holocene sediments in the Ulleung Basin are characterized by several volcanic tephra layers with alternations of fine light and dark clayey layers, reflecting variability in the paleoenvironment. Based on the previous researches and AMS results, we determine the ages of sedimentary layers from three tephra layers, 1.86 mbsf (U-Oki, 10.7 ka), 3.31 mbsf (AT, 29.4 ka), 11.67 mbsf (Aso-4, 88.0 ka) and 17.09 mbsf (Aso-3, 133.0 ka) respectively. Sediment textures are identified as hemipelagic mud, bioturbated mud and laminated mud with tephra layers. The sedimentation rates of each intervals are 0.174 m/kyr (present to U-Oki), 0.078 m/kyr (U-Oki to AT), 0.143 m/kyr (AT to Aso-4) and 0.120 m/kyr (Aso-4 to Aso-3) respectively. Sensitivity of XRF core scanner was obtained by establishing equivalences between peak areas. Element concentrations are analyzed by traditional techniques such as ICP-MS, ICP-OES. The Ca/Fe ratio reflects carbonate content and ISA-16ESUB-2B core shows strong correlation to sedimentary horizons. Sr/Ca ratio has good correlation with sedimentary units. Enhanced Sr contents indicates strong surface ocean production. Br/Cl ratio are high peak during MIS 5.5. Br content implies generally high organic rich sediments.

Provenance and depositional history of continental slope sediments in the Southwestern Gulf of Mexico unraveled by geochemical analysis

NASA Astrophysics Data System (ADS)

Armstrong-Altrin, John S.; Machain-Castillo, María Luisa; Rosales-Hoz, Leticia; Carranza-Edwards, Arturo; Sanchez-Cabeza, Joan-Albert; Ruíz-Fernández, Ana Carolina

2015-03-01

The aim of this work is to constrain the provenance and depositional history of continental slope sediments in the Southwestern Gulf of Mexico (~1089-1785 m water depth). To achieve this, 10 piston sediment cores (~5-5.5 m long) were studied for mineralogy, major, trace and rare earth element geochemistry. Samples were analyzed at three core sections, i.e. upper (0-1 cm), middle (30-31 cm) and lower (~300-391 cm). The textural study reveals that the core sediments are characterized by silt and clay fractions. Radiocarbon dating of sediments for the cores at different levels indicated a maximum of ~28,000 year BP. Sediments were classified as shale. The chemical index of alteration (CIA) values for the upper, middle, and lower sections revealed moderate weathering in the source region. The index of chemical maturity (ICV) and SiO2/Al2O3 ratio indicated low compositional maturity for the core sediments. A statistically significant correlation observed between total rare earth elements (∑REE) versus Al2O3 and Zr indicated that REE are mainly housed in detrital minerals. The North American Shale Composite (NASC) normalized REE patterns, trace element concentrations such as Cr, Ni and V, and the comparison of REE concentrations in sediments and source rocks indicated that the study area received sediments from rocks intermediate between felsic and mafic composition. The enrichment factor (EF) results indicated that the Cd and Zn contents of the upper section sediments were influenced by an anthropogenic source. The trace element ratios and authigenic U content of the core sediments indicated the existence of an oxic depositional environment.

Nuclear radiation actuated valve

DOEpatents

Christiansen, David W.; Schively, Dixon P.

1985-01-01

A nuclear radiation actuated valve for a nuclear reactor. The valve has a valve first part (such as a valve rod with piston) and a valve second part (such as a valve tube surrounding the valve rod, with the valve tube having side slots surrounding the piston). Both valve parts have known nuclear radiation swelling characteristics. The valve's first part is positioned to receive nuclear radiation from the nuclear reactor's fuel region. The valve's second part is positioned so that its nuclear radiation induced swelling is different from that of the valve's first part. The valve's second part also is positioned so that the valve's first and second parts create a valve orifice which changes in size due to the different nuclear radiation caused swelling of the valve's first part compared to the valve's second part. The valve may be used in a nuclear reactor's core coolant system.

Analysis of the volatile organic matter of engine piston deposits by direct sample introduction thermal desorption gas chromatography/mass spectrometry.

PubMed

Diaby, M; Kinani, S; Genty, C; Bouchonnet, S; Sablier, M; Le Negrate, A; El Fassi, M

2009-12-01

This article establishes an alternative method for the characterization of volatiles organic matter (VOM) contained in deposits of the piston first ring grooves of diesel engines using a ChromatoProbe direct sample introduction (DSI) device coupled to gas chromatography/mass spectrometry (GC/MS) analysis. The addition of an organic solvent during thermal desorption leads to an efficient extraction and a good chromatographic separation of extracted products. The method was optimized investigating the effects of several solvents, the volume added to the solid sample, and temperature programming of the ChromatoProbe DSI device. The best results for thermal desorption were found using toluene as an extraction solvent and heating the programmable temperature injector from room temperature to 300 degrees C with a temperature step of 105 degrees C. With the use of the optimized thermal desorption conditions, several components have been positively identified in the volatile fraction of the deposits: aromatics, antioxidants, and antioxidant degradation products. Moreover, this work highlighted the presence of diesel fuel in the VOM of the piston deposits and gave new facts on the absence of the role of diesel fuel in the deposit formation process. Most importantly, it opens the possibility of quickly performing the analysis of deposits with small amounts of samples while having a good separation of the volatiles.

Trace metal in sediment from a deep-sea floor of Makassar Strait

NASA Astrophysics Data System (ADS)

Budianto, F.; Lestari

2018-02-01

Makassar Strait is located in the entrance of Indonesian Through Flow (ITF). However, the geochemistry of metals in sediment within Makassar Strait remains unexplored. The aim of this study was to measure the concentration of metals in sediment and to assess the sediment quality based on those metals concentrations. The sediment was collected from 632-4730 m in depth using giant piston corer on R/V Baruna Jaya VIII in December 2014. In each observation point, three layers of sediment were sub-sampled from the core i.e. surface layer (0-5 cm), middle layer (45-55 cm) and bottom layer. The metals were analyzed using acid digestion procedure followed by Atomic Absorption Spectrophotometer. The result indicated that the metal has spatially insignificant differences in sediment and the increase of metal concentration by depth was noticed. The Enrichment factor presented as no enrichment to minor enrichment of metal in sediment.

Composite piston

NASA Technical Reports Server (NTRS)

Taylor, Allan H. (Inventor)

1988-01-01

A composite piston structure is disclosed which provides a simple and reliable means for joining a carbon-carbon or ceramic piston cap with a metallic piston body. Attachment is achieved by means of a special geometry which compensates for differences in thermal expansion without complicated mechanical fastening devices. The shape employs a flange created by opposed frustoconical shapes with coincident vertices intersecting on the radial centerline of the piston in order to retain the piston cap. The use of carbon-carbon for the piston cap material allows a close fit between the piston and a cylinder wall, eliminating the need for piston rings. The elimination of extra mechanical parts of previous composite pistons provides a lightweight composite piston capable of extended high temperature operation.

Geomagnetic paleointensity dating of South China Sea sediments for the last 130 kyr

NASA Astrophysics Data System (ADS)

Xiaoqiang, Yang; Heller, Friedrich; Nengyou, Wu; Jie, Yang; Zhihua, Su

2009-06-01

Relative paleointensity records from the northern South China Sea, northwest Pacific Ocean were studied in two gravity piston cores. Continuous mineral magnetic and paleomagnetic measurements were made using discrete sediment samples. Detailed rock magnetic parameters, such as thermomagnetic and high-field hysteresis data, indicate that pseudo-single domain magnetite in a narrow range of grain-size and concentration is the main contributor to the remanent magnetization. The uniform magnetic mineralogy meets the commonly accepted criteria for establishing relative paleointensity records. The relative paleointensity (RPI) curves were constructed by normalizing the natural remanent magnetization (NRM) with isothermal remanent magnetization (IRM), both in the 20-60 mT demagnetization state. Dating constraints have been provided by radiocarbon ages in the upper 400 cm of both cores. Furthermore, we have correlated our paleointensity records with NAPIS-75, S.Atlantic-1089, Sint-200 and NOPAPIS-250 to determine the chronological RPI framework for the South China Sea (SCS-PIS). Although some temporal offsets of paleointensity features between the different records have been recognized, their similar shape suggests that relative paleointensity on the 10 3-10 4 year scale is globally coherent and can provide an age framework for sediments independent of δ18O ages.

Unmelted meteoritic debris in the Late Pliocene iridium anomaly - Evidence for the ocean impact of a nonchondritic asteroid

NASA Technical Reports Server (NTRS)

Kyte, F. T.; Brownlee, D. E.

1985-01-01

Ir-bearing particles have been recovered from two piston cores in the Antarctic Basin in the southeastern Pacific. In core E13-3, the particles closely correspond to the Late Pliocene Ir anomaly and have a fluence of about 100 mg/cm sq. In core E13-4, 120 km to the southwest, the particle fluence is about 4 mg/cm sq. Particles with diameters from 0.5 to 4 mm contain at least 35 percent of the Ir in this horizon. Three types of particles have been identified: (1) vesicular, (2) basaltic, and (3) metal. The vesicular particles appear to be shock-melted debris derived from the oceanic impact of a howarditic asteroid containing a minor metal component. These particles have recrystallized from a melt and impact into the ocean has resulted in the incorporation of Na, K, Cl, and radiogenic Sr from the ocean water target. The basaltic clasts appear to be unmelted fragments of the original asteroid which may have separated from the main body prior to impact. Combined vesicular and basaltic particles are believed to have formed by collisions in the debris cloud. Estimates of the diameter of the projectile range from 100 to 500 m. By many orders of magnitude, this is the most massive achondrite sampled by a single meteorite fall.

Estimates of tracer-based piston-flow ages of groundwater from selected sites-National Water-Quality Assessment Program, 1992-2005

USGS Publications Warehouse

Hinkle, Stephen R.; Shapiro, Stephanie D.; Plummer, Niel; Busenberg, Eurybiades; Widman, Peggy K.; Casile, Gerolamo C.; Wayland, Julian E.

2011-01-01

This report documents selected age data interpreted from measured concentrations of environmental tracers in groundwater from 1,399 National Water-Quality Assessment (NAWQA) Program groundwater sites across the United States. The tracers of interest were chlorofluorocarbons (CFCs), sulfur hexafluoride (SF6), and tritium/helium-3 (3H/3He). Tracer data compiled for this analysis primarily were from wells representing two types of NAWQA groundwater studies - Land-Use Studies (shallow wells, usually monitoring wells, in recharge areas under dominant land-use settings) and Major-Aquifer Studies (wells, usually domestic supply wells, in principal aquifers and representing the shallow, used resource). Reference wells (wells representing groundwater minimally impacted by anthropogenic activities) associated with Land-Use Studies also were included. Tracer samples were collected between 1992 and 2005, although two networks sampled from 2006 to 2007 were included because of network-specific needs. Tracer data from other NAWQA Program components (Flow System Studies, which are assessments of processes and trends along groundwater flow paths, and various topical studies) were not compiled herein. Tracer data from NAWQA Land-Use Studies and Major-Aquifer Studies that previously had been interpreted and published are compiled herein (as piston-flow ages), but have not been reinterpreted. Tracer data that previously had not been interpreted and published are evaluated using documented methods and compiled with aqueous concentrations, equivalent atmospheric concentrations (for CFCs and SF6), estimates of tracer-based piston-flow ages, and selected ancillary data, such as redox indicators, well construction, and major dissolved gases (N2, O2, Ar, CH4, and CO2). Tracer-based piston-flow ages documented in this report are simplistic representations of the tracer data. Tracer-based piston-flow ages are a convenient means of conceptualizing groundwater age. However, the piston-flow model is based on the potentially limiting assumptions that tracer transport is advective and that no mixing occurs. Additional uncertainties can arise from tracer degradation, sorption, contamination, or fractionation; terrigenic (natural) sources of tracers; spatially variable atmospheric tracer concentrations; and incomplete understanding of mechanisms of recharge or of the conditions under which atmospheric tracers were partitioned to recharge. The effects of some of these uncertainties are considered herein. For example, degradation, contamination, or fractionation often can be identified or inferred. However, detailed analysis of the effects of such uncertainties on the tracer-based piston-flow ages is constrained by sparse data and an absence of complementary lines of evidence, such as detailed solute transport simulations. Thus, the tracer-based piston-flow ages compiled in this report represent only an initial interpretation of the tracer data.

Distal deltaic deposits document hydrological variability during the past 30 kyrBP in Lake Towuti, Indonesia

NASA Astrophysics Data System (ADS)

Vogel, Hendrik; Russell, James M.; Yudawati Cahyarini, Sri; Bijaksana, Satria; Wattrus, Nigel; Rethemeyer, Janet; Melles, Martin

2014-05-01

Lake Towuti (2.75°S, 121.5°E; 318 m a.s.l.) is a, 560 km2, 200-m deep tectonic lake at the downstream end of the Malili lake system, a set of five, ancient (1-2 MYr) tectonic lakes in central Sulawesi, Indonesia. The Mahalona River constitutes the largest tributary and connects Lake Towuti with the two upstream lakes Matano and Mahalona. The Mahalona River Delta is prograding into the >200m deep northern basin of Lake Towuti. Tracing past variability of Mahalona River discharge is therefore an important puzzle piece for the understanding of depositional dynamics in Lake Towuti as well as catchment hydrology and hydrological connectivity between the Malili Lakes. Distal deltaic deposits can help identifying past variability in river discharge and delta dynamics. Using highly resolved seismic reflection data collected between 2007-2013 we identified a stack of acoustically laminated reflections in Towuti's extensive and morphologically flat deep northern basin. For detailed characterization of these acoustic features we collected a c. 20m long piston core from the basin centre at 200 m water depth reaching back to c. 30 kyrBP. Sediments in this piston core consist to 75% of mass wasting deposits (MWD) of variable thickness that are intercalated with pelagic muds (25%). MWD appear mostly homogenous (silt- to finesand-sized siliciclastics with high amounts of terrestrial plant macrofossils) with only thin (1-3 cm) basal sand layers and clay caps (<1 cm). Pelagic muds appear as thin to medium bedded slightly silty clays that are clearly distinguishable from MWD. The position of MWD identified in our piston core nicely correlates with acoustically laminated reflections identified in seismic profiles crossing the coring site. Based on these combined sedimentological and acoustic datasets we interpret MWD in Towuti's northern basin as distal deltaic deposits originating from the Mahalona River Delta. Frequencies and percentages (in terms of lithofacies contribution) of distal deltaic deposits differ substantially between the Holocene (56%) and last glacial (88%) sediment succession. In combination with data from hydrological proxies and seismic reflection data indicating dry climate conditions and lake level lowstands, respectively, we interpret the higher frequency of distal deltaic deposits during the last glacial as a result of subaerial exposure and erosion of Mahalona River Delta sediments. These findings imply that frequencies and percentages of distal deltaic deposits in Lake Towuti may be an additional indicator for hydrological variability in this particular system.

Post STS-133 Evaluation of Main Flame Deflector Witness Materials

NASA Technical Reports Server (NTRS)

Long, Victoria

2011-01-01

NASA and USA Structures engineers submitted main flame deflector witness materials for evaluation after the launch of STS-133. The following items were submitted for analysis: HY-80 steel witness rods, 304 stainless steel caps, tungsten pistons, 17-4 precipitation hardened (PH) stainless steel and A-286 piston sleeves, Medtherm Corporation calorimeters, and Nanmac Corporation thermocouples. All of the items were photographed in order to document their condition after the launch of STS-133, and before they were reinstalled at the launch pad for future launches. The HY -80 witness rods, 304 stainless steel caps, and the piston sleeves were dimensionally measured in order to determine the amount of material lost during launch. Microstructural changes were observed in the HY-80 witness rod and 304 stainless steel cap metallographic samples due to the heat of the launch.

Piston rod seal

DOEpatents

Lindskoug, Stefan

1984-01-01

In a piston rod seal of the type comprising a gland through which the piston rod is passed the piston is provided with a sleeve surrounding the piston rod and extending axially so as to axially partly overlap the gland when the piston is in its bottom dead center position.

High resolution paleo-geomagnetic field variations as recorded in sediments from Prince William Sound, Alaska

NASA Astrophysics Data System (ADS)

Ziegler, Leah; Stoner, Joseph

2013-04-01

The dynamic changes in the Earth's magnetic field, caused by fluid motions in its outer core, can be captured in global marine sediments. Here we extend recent efforts to reconstruct Holocene paleomagnetic secular variation and environmental conditions in the mid-high latitude North Pacific with analyses of a marine sediment core taken from Prince William Sound, southern Alaska. Natural and laboratory remanent magnetizations were studied by progressive alternating field (AF) demagnetization of u-channel samples from jumbo piston core EW0408-95JC (60.66278N, 147.70847W, water depth 745m). The lithology is monitored by physical properties measurements, including CT Scans and core descriptions. The lithology of the upper 8.5 m of the 17.6 meter core consists primarily of magnetically homogenous bioturbated muds. Component directions calculated by PCA analysis are characterized by low MAD values (<4°) with inclinations consistent with GAD predictions and declinations varying in a manner consistent with PSV. Normalized remanences are comparable using a variety of normalizers and show minimal scatter through demagnetization suggesting that reliable paleointenisty estimates may be preserved. A detailed chronology developed from calibrated radiocarbon dating of benthic forams shows that the 8.5m spans ~1500 years, and yields sedimentation rates of several hundred cm/kyr - ultra high for marine sediments. Comparison with Pacific Northwest and broader North American records, provides a degree of reproducibility and allows us to assess the spatial scale of signal coherence at centennial resolution . The resulting record of paleosecular variation (PSV) and relative paleointensity are consistent with predictions from global geomagnetic field models, yet allow investigations of rates of change of the local field, that cannot be accessed from global field models.

Method and apparatus for pressurizing vaporous fluids

DOEpatents

Bingham, Dennis N.; Ferguson, Russell L.

2001-01-01

Pump apparatus according to the present invention may comprise a pump body having a bore therein and a piston mounted within the bore so that the piston may be reciprocated within the bore between first and second positions. A sleeve seal assembly mounted to the pump body contacts the piston as the piston moves between the first and second positions. A piston seal assembly mounted to the piston contacts the bore in the pump body and is located on the piston so that the piston seal assembly does not contact the sleeve seal assembly as the piston is reciprocated between the first and second positions within the bore of the pump body.

Mechano-Chemical Interactions at Cement-Geomaterial Interfaces in Repository and Borehole Scenarios

NASA Astrophysics Data System (ADS)

Mohagheghi, J. R.; Dewers, T. A.; Matteo, E. N.; Heath, J. E.; Jove Colon, C. F.; Fuller, T.

2017-12-01

A number of factors negatively affect wellbore integrity including interactions at boundaries between cement and surrounding geomaterial. These include mechanical and chemical mechanisms that can lead to wellbore failure. To examine these interactions, potential coupling, and pathways to failure, we discuss progress on an experimental and modeling study involving cement-clay and cement-salt interfaces. A sample shotcrete-bentonite interface from the FEBEX heater test at the Grimsel Test Site in Switzerland is examined using multi-beam scanning electron microscopy (mSEM) at 4 nm resolution over an area 10's of square millimeters. We examine changes in alteration as manifested by pore structural changes as a function of distance from the interface. A parallel effort examines time-dependent changes in interface structure in cement cores in a triaxial coreholder. Cores are exposed to conditions of 70oC, 14 MPa pressure, and small differential loads, with degradation being monitored by effluent pH, pulse-echo ultrasonics, and piston displacement (measuring sample shortening). We will measure the mechanical consequences of interface alteration using nano-indentation. Experimental results are being incorporated as a validation effort in a coupled reactive-transport mechanics model linking the Sandia ALBANY finite element code, the KAYENTA elasto-plastic constitutive model, with the reactive transport code PFLOTRAN. Plans call to apply the model to understanding the evolution of the FEBEX sample, as well as a cement-salt sample from the Waste Isolation Pilot Plant in Carlsbad, New Mexico. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of Honeywell International Inc. for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA0003525. SAND 2017-8277 A

Drift stabilizer for reciprocating free-piston devices

DOEpatents

Ward, William C.; Corey, John A.; Swift, Gregory W.

2003-05-20

A free-piston device has a stabilized piston drift. A piston having a frequency of reciprocation over a stroke length and with first and second sides facing first and second variable volumes, respectively, for containing a working fluid defining an acoustic wavelength at the frequency of reciprocation. A bypass tube waveguide connects the first and second variable volumes at all times during reciprocation of the piston. The waveguide has a relatively low impedance for steady flow and a relatively high impedance for oscillating flow at the frequency of reciprocation of the piston, so that steady flow returns fluid leakage from about the piston between the first and second volumes while oscillating flow is not diverted through the waveguide. Thus, net leakage about the piston is returned during each stroke of the piston while oscillating leakage is not allowed and pressure buildup on either the first or second side of the piston is avoided to provide a stable piston location.

49 CFR 229.55 - Piston travel.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Piston travel. 229.55 Section 229.55... Piston travel. (a) Brake cylinder piston travel shall be sufficient to provide brake shoe clearance when... piston travel may not exceed 11/2 inches less than the total possible piston travel. The total possible...

A low-background piston-cylinder-type hybrid high pressure cell for muon-spin rotation/relaxation experiments

NASA Astrophysics Data System (ADS)

Shermadini, Z.; Khasanov, R.; Elender, M.; Simutis, G.; Guguchia, Z.; Kamenev, K. V.; Amato, A.

2017-10-01

A low background double-wall piston-cylinder-type pressure cell is developed at the Paul Scherrer Institute. The cell is made from BERYLCO-25 (beryllium copper) and MP35N nonmagnetic alloys with the design and dimensions which are specifically adapted to muon-spin rotation/relaxation (μSR) measurements. The mechanical design and performance of the pressure cell are evaluated using finite-element analysis (FEA). By including the measured stress-strain characteristics of the materials into the finite-element model, the cell dimensions are optimized with the aim to reach the highest possible pressure while maintaining the sample space large (6 mm in diameter and 12 mm high). The presented unconventional design of the double-wall piston-cylinder pressure cell with a harder outer MP35N sleeve and a softer inner CuBe cylinder enables pressures of up to 2.6 GPa to be reached at ambient temperature, corresponding to 2.2 GPa at low temperatures without any irreversible damage to the pressure cell. The nature of the muon stopping distribution, mainly in the sample and in the CuBe cylinder, results in a low-background μSR signal.

Containerless high-pressure petrology experiments in the microgravity environment of the Space Station

NASA Technical Reports Server (NTRS)

Boynton, W. V.; DRAKE; HILDEBRAND; JONES; LEWIS; TREIMAN; WARK

1987-01-01

The genesis of igneous rocks on terrestrial planets can only be understood through experiments at pressures corresponding to those in planetary mantles (10 to 50 kbar). Such experiments typically require a piston-cylinder apparatus, and an apparatus that has the advantage of controllable pressure and temperature, adequate sample volume, rapid sample quench, and minimal danger of catastrophic failure. It is proposed to perform high-pressure and high-temperature piston-cylinder experiments aboard the Space Station. The microgravity environment in the Space Station will minimize settling due to density contrasts and may, thus, allow experiments of moderate duration to be performed without a platinoid capsule and without the sample having to touch the container walls. The ideal pressure medium would have the same temperatures. It is emphasized, however, that this proposed experimental capability requires technological advances and innovations not currently available.

Comparison of Nitinol Stapes Pistons with Conventional Stapes Pistons: A Cadaver Study

DTIC Science & Technology

2011-01-01

Comparison of Nitinol Stapes Pistons with Conventional Stapes Pistons: A Cadaver Study Samuel A. Spear1 and James V. Crawford2 1 48th Medical Group, ENT...cited. Objective. To visually compare the Nitinol “smart” stapes prosthesis to conventional manual crimping stapes pistons in temporal bone cadaver...answer questions about each stapes piston. The answers to the survey were then recorded for analysis. Results. 8 of 9 Nitinol pistons were described as

An Experimental and numerical Study for squeezing flow

NASA Astrophysics Data System (ADS)

Nathan, Rungun; Lang, Ji; Wu, Qianhong; Vucbmss Team

2017-11-01

We report an experimental and numerical study to examine the transient squeezing flow driven by sudden external impacts. The phenomenon is widely observed in industrial applications, e.g. squeeze dampers, or in biological systems, i.e. joints lubrication. However, there is a lack of investigation that captures the transient flow feature during the process. An experimental setup was developed that contains a piston instrumented with a laser displacement sensor and a pressure transducer. The heavy piston was released from rest, creating a fast compaction on the thin fluid gap underneath. The motion of the piston and the fluid pressure build-up was recorded. For this dynamic process, a CFD simulation was performed which shows excellent agreement with the experimental data. Both the numerical and experimental results show that, the squeezing flow starts with the inviscid limit when the viscous fluid effect has no time to appear, and thereafter becomes a developing flow, in which the inviscid core flow region decreases and the viscous wall region increases until the entire fluid gap is filled with viscous fluid flow. The study presented herein, filling the gap in the literature, will have broad impacts in industrial and biomedical applications. This research was supported by the National Science Foundation under Award 1511096, and supported by the Seed Grant from The Villanova Center for the Advancement of Sustainability in Engineering (VCASE).

Systematics of Alkali Metals in Pore Fluids from Serpentinite Mud Volcanoes: IODP Expedition 366

NASA Astrophysics Data System (ADS)

Wheat, C. G.; Ryan, J.; Menzies, C. D.; Price, R. E.; Sissmann, O.

2017-12-01

IODP Expedition 366 focused, in part, on the study of geo­chemical cycling, matrix alteration, material and fluid transport, and deep biosphere processes within the subduction channel in the Mariana forearc. This was accomplished through integrated sampling of summit and flank regions of three active serpentinite mud volcanoes (Yinazao (Blue Moon), Asùt Tesoro (Big Blue), and Fantangisña (Celestial) Seamounts). These edifices present a transect of depths to the Pacific Plate, allowing one to characterize thermal, pressure and compositional effects on processes that are associated with the formation of serpentinite mud volcanoes and continued activity below and within them. Previous coring on ODP Legs 125 and 195 at two other serpentinite mud volcanoes (Conical and South Chamorro Seamounts) and piston, gravity, and push cores from several other Mariana serpentinite mud volcanoes add to this transect of sites where deep-sourced material is discharged at the seafloor. Pore waters (149 samples) were squeezed from serpentinite materials to determine the composition of deep-sourced fluid and to assess the character, extent, and effect of diagenetic reactions and mixing with seawater on the flanks of the seamounts as the serpentinite matrix weathers. In addition two Water Sampler Temperature Tool (WSTP) fluid samples were collected within two of the cased boreholes, each with at least 30 m of screened casing that allows formations fluids to discharge into the borehole. Shipboard results for Na and K record marked seamount-to-seamount differences in upwelling summit fluids, and complex systematics in fluids obtained from flank sites. Here we report new shore-based Rb and Cs measurements, two elements that have been used to constrain the temperature of the deep-sourced fluid. Data are consistent with earlier coring and drilling expeditions, resulting in systematic changes with depth (and by inference temperature) to the subduction channel.

Current shunting and formation of stationary shock waves during electric explosions of metal wires in air

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ivanenkov, G. V.; Gus'kov, S. Yu.; Barishpol'tsev, D. V.

2010-01-15

Results of experiments on the generation of shock waves during electric explosions of fine copper and tungsten wires in air are analyzed. The generation mechanism of stationary shock wave by a plasma piston formed during the shunting breakdown of the electrode gap in the course of a wire explosion is investigated. The role of structural elements of such discharges, such as the core, corona, and wire environment, is analyzed.

Investigation on the radial micro-motion about piston of axial piston pump

NASA Astrophysics Data System (ADS)

Xu, Bing; Zhang, Junhui; Yang, Huayong; Zhang, Bin

2013-03-01

The limit working parameters and service life of axial piston pump are determined by the carrying ability and lubrication characteristic of its key friction pairs. Therefore, the design and optimization of the key friction pairs are always a key and difficult problem in the research on axial piston pump. In the traditional research on piston/cylinder pair, the assembly relationship of piston and cylinder bore is simplified into ideal cylindrical pair, which can not be used to analyze the influences of radial micro-motion of piston on the distribution characteristics of oil-film thickness and pressure in details. In this paper, based on the lubrication theory of the oil film, a numerical simulation model is built, taking the influences of roughness, elastic deformation of piston and pressure-viscosity effect into consideration. With the simulation model, the dynamic characteristics of the radial micro-motion and pressure distribution are analyzed, and the relationships between radial micro-motion and carrying ability, lubrication condition, and abrasion are discussed. Furthermore, a model pump for pressure distribution measurement of oil film between piston and cylinder bore is designed. The comparison of simulation and experimental results of pressure distribution shows that the simulation model has high accuracy. The experiment and simulation results demonstrate that the pressure distribution has peak values that are much higher than the boundary pressure in the piston chamber due to the radial micro-motion, and the abrasion of piston takes place mainly on the hand close to piston ball. In addition, improvement of manufacturing roundness and straightness of piston and cylinder bore is helpful to improve the carrying ability of piston/cylinder pair. The proposed research provides references for designing piston/cylinder pair, and helps to prolong the service life of axial piston pump.

Drive piston assembly for a valve actuator assembly

DOEpatents

Sun, Zongxuan

2010-02-23

A drive piston assembly is provided that is operable to selectively open a poppet valve. The drive piston assembly includes a cartridge defining a generally stepped bore. A drive piston is movable within the generally stepped bore and a boost sleeve is coaxially disposed with respect to the drive piston. A main fluid chamber is at least partially defined by the generally stepped bore, drive piston, and boost sleeve. First and second feedback chambers are at least partially defined by the drive piston and each are disposed at opposite ends of the drive piston. At least one of the drive piston and the boost sleeve is sufficiently configured to move within the generally stepped bore in response to fluid pressure within the main fluid chamber to selectively open the poppet valve. A valve actuator assembly and engine are also provided incorporating the disclosed drive piston assembly.

Design and analysis of piston by Al-GHS 1300, Al-GHY 1250, Al-Si-C, A6061 and A4032 composite material: A review

NASA Astrophysics Data System (ADS)

Misra, Sheelam; Agrawal, Ankush

2018-05-01

Over the past decades the piston is designed to transfer force to the crank shaft through a piston rod by the expansion of gases in the cylinder. During working piston has to tolerate the cyclic gas pressure and the inertial forces, due to which the piston experiences fatigue damages such as piston side wear, piston head cracks and so on. Earlier pistons were made up of cast iron or aluminium due to their lightweight and high heat transfer rate. After some experiments it was noted that on heating cast iron expands due to which it covers the clearance level that comes to seize the engine. This paper aims to design a piston using composite material such as Al-GHS 1300, Al-GHY 1250, Al-Si-C, A6061 and A4032 that will differ the material and the characteristics of the traditional engine piston. This paper describes the thermal and mechanical properties of the piston when the study is done by taking five different materials.

Split ring floating air riding seal for a turbine

DOEpatents

Mills, Jacob A

2015-11-03

A floating air riding seal for a gas turbine engine with a rotor and a stator, an annular piston chamber with an axial moveable annular piston assembly within the annular piston chamber, an annular cavity formed on the annular piston assembly that faces a seal surface on the rotor, and a central passage connecting the annular cavity to the annular piston chamber to supply compressed air to the seal face, where the annular piston assembly is a split piston assembly to maintain a tight seal as coning of the rotor disk occurs.

Conical seat shut off valve

NASA Technical Reports Server (NTRS)

Farner, Bruce R. (Inventor)

2012-01-01

A valve includes a housing defining a bore having an inlet and extending along a longitudinal axis. A head is attached to the housing and defines a head passage having an outlet. A piston is disposed within the bore and includes a piston passage extending through the piston along the longitudinal axis. The piston is moveable between a closed position in which a sealing end of the piston abuts a seat of the head to close fluid communication through the piston passage and an open position in which the sealing end of the piston is axially spaced along the longitudinal axis from the seat of the head to permit fluid communication through the piston passage between the inlet and the outlet. The housing defines an equalizing chamber in fluid communication with the head passage for damping movement of the piston.

Holocene Ostracoda from the Herald Canyon, Eastern Siberian Sea from the SWERUS-C3 Expedition 2014

NASA Astrophysics Data System (ADS)

Gemery, L.; Cronin, T. M.; Jakobsson, M.; Barrientos, N.; O'Regan, M.; Muschitiello, F.; Koshurnikov, A.; Gukov, A.

2015-12-01

We analyzed Arctic benthic ostracode assemblages from two piston cores (PC) and their complementary multicores from Herald Canyon in the Eastern Siberian Sea. The cores (SWERUS-L2-2-PC1 [8.1 m], 2-MUC4, 71.7 m water depth, and SWERUS-L2-4-PC1 [6.2 m], 4-MUC4, 119.7 m water depth) were collected during Leg 2 of the 2014 SWERUS-C3 Expedition. Radiocarbon dates on mollusks indicate that sediments from 2-PC1 and 4-PC1 were deposited over the last 5,000 and 10,000 years respectively. The dominant ostracode species include: Acanthocythereis dunelmensis, Cytheropteron elaeni, Elofsonella concinna, Kotoracythere janae, Normanicythere leioderma, Semicytherura complanata. Based on species' distributions obtained from a 1,200-sample modern ostracode database, these species are known to be typical of shallow mid- to outer-continental shelf environments in the modern Arctic Ocean. The abundant and diverse benthic ostracode assemblages found in these cores suggest the influence of nutrient-rich Pacific water flowing in through the Bering Strait. The faunal assemblages are fairly uniform throughout 2-PC1, suggesting minimal variability in Pacific water inflow since at least 5 ka. In the lower section of 4-PC1, there is a major change to ostracode assemblages containing typical inner shelf, often brackish-water species, such as Cytheromorpha macchesneyi, and associated shallow Arctic shelf species (Sarsicytheridea punctillata and several Cytheropteron species), reflecting a period of lower, deglacial sea level.

Gas exchange and CO2 flux in the tropical Atlantic Ocean determined from Rn-222 and pCO2 measurements

NASA Technical Reports Server (NTRS)

Smethie, W. M., Jr.; Takahashi, T.; Chipman, D. W.; Ledwell, J. R.

1985-01-01

The piston velocity for the tropical Atlantic Ocean has been determined from 29 radon profiles measured during the TTO Tropical Atlantic Study. By combining these data with the pCO2 data measured in the surface water and air samples, the net flux of CO2 across the sea-air interface has been calculated for the tropical Atlantic. The dependence of the piston velocity on wind speed is discussed, and possible causes for the high sea-to-air CO2 flux observed in the equatorial zone are examined.

Post STS-134 Evaluation of Main Flame Deflector Witness Materials

NASA Technical Reports Server (NTRS)

Long, Victoria

2011-01-01

NASA and USA design engineers submitted witness materials from the solid rocket booster (SRB) main flame deflector for evaluation after the launch of STS-134. The following items were submitted for analysis: 1018 steel witness rods 304 stainless steel caps, tungsten pistons, and A-286 piston sleeves. All of the items were photographed in order to document their condition after the launch of STS-134. All of the items were dimensionally measured in order to determine the amount of material lost during launch. Microstructural changes were observed in the 1018 witness rod metallographic samples due to the heat of the launch

Resonant acoustic measurement of vapor phase transport phenomenon in porous media

NASA Astrophysics Data System (ADS)

Schuhmann, Richard; Garrett, Steven

2002-05-01

Diffusion of gases through porous media is commonly described using Fick's law and is characterized by a gas diffusion coefficient modified by a media-specific tortuosity parameter. A phase-locked-loop resonance frequency tracker [J. Acoust. Soc. Am. 108, 2520 (2000)] has been upgraded with an insulated copper resonator and a bellows-sealed piston instrumented with an accelerometer. Average system stability (temperature divided by frequency squared) is about 180 ppm. Glass-bead-filled cores of different lengths are fitted into an o-ring sealed opening at the top of the resonator. The rate at which the tracer gas is replaced by air within the resonator is controlled by the core's diffusion constant. Mean molecular weight of the gas mixture in the resonator is determined in real time from the ratio of the absolute temperature to the square of the fundamental acoustic resonance frequency. Molecular weight of the gas mixture is determined approximately six times per minute. Changes in the gas mixture concentration are exponential in time (within 0.1%) over nearly two decades in concentration. We will report diffusion constants for two different sizes of glass beads, in samples of five different lengths, using two different tracer gases, to establish the validity of this approach. [Work supported by ONR.

Pleistocene calcareous nannofossil biochronology at IODP Site U1385 (Expedition 339)

NASA Astrophysics Data System (ADS)

Balestra, B.; Flores, J.-A.; Hodell, D. A.; Hernández-Molina, F. J.; Stow, D. A. V.

2015-12-01

During Integrated Ocean Drilling Program (IODP) Expedition 339, Site U1385 (37°34‧N, 10°7‧W, 2578 m below sea level) was drilled in the lower slope of the Portuguese margin, to provide a marine reference section of Pleistocene millennial-scale climate variability. Five holes were cored using the Advanced Piston Corer (APC) to a depth of ~ 151 m below sea floor (mbsf) recovering a continuous stratigraphic record covering the past 1.4 Ma. Here we present results of the succession of standard and unconventional calcareous nannofossil biostratigraphic events. The quantitative study of calcareous nannofossils showed well-preserved and abundant assemblages throughout the core. Most conventional Pleistocene events were recognized and the timing of bioevents were calibrated using correlation to the new oxygen isotope stratigraphy record developed for the Site U1385. The analyses provide further data on the stratigraphic distribution of selected species and genera, such as the large Emiliania huxleyi (> 4 μm), Gephyrocapsa caribbeanica, Helicosphaera inversa, Gephyrocapsa omega and Reticulofenestra asanoi (> 6 μm) and other circular-subcircular small reticulofenestrids, resulting in new insights into the environmental control of their stratigraphic patterns. Finally, the comparison between nannofossil datums and oxygen isotope stratigraphy on the same samples has resulted in an accurate revision of timing of the events, providing valuable biochronologic information.

Integral Ring Carbon-Carbon Piston

NASA Technical Reports Server (NTRS)

Northam, G. Burton (Inventor)

1999-01-01

An improved structure for a reciprocating internal combustion engine or compressor piston fabricate from carbon-carbon composite materials is disclosed. An integral ring carbon-carbon composite piston, disclosed herein, reduces the need for piston rings and for small clearances by providing a small flexible, integral component around the piston that allows for variation in clearance due to manufacturing tolerances, distortion due to pressure and thermal loads, and variations in thermal expansion differences between the piston and cylinder liner.

Speed control with end cushion for high speed air cylinder

DOEpatents

Stevens, Wayne W.; Solbrig, Charles W.

1991-01-01

A high speed air cylinder in which the longitudinal movement of the piston within the air cylinder tube is controlled by pressurizing the air cylinder tube on the accelerating side of the piston and releasing pressure at a controlled rate on the decelerating side of the piston. The invention also includes a method for determining the pressure required on both the accelerating and decelerating sides of the piston to move the piston with a given load through a predetermined distance at the desired velocity, bringing the piston to rest safely without piston bounce at the end of its complete stroke.

Analysis of Piston Slap Motion

NASA Astrophysics Data System (ADS)

Narayan, S.

2015-05-01

Piston slap is the major force contibuting towards noise levels in combustion engines.This type of noise depends upon a number of factors such as the piston-liner gap, type of lubricant used, number of piston pins as well as geometry of the piston. In this work the lateral and rotary motion of the piston in the gap between the cylinder liner and piston has been analyzed. A model that can predict the forces and response of the engine block due to slap has been dicussed. The parameters such as mass, spring and damping constant have been predicted using a vibrational mobility model.

Carbon-carbon piston development

NASA Technical Reports Server (NTRS)

Gorton, Mark P.

1994-01-01

A new piston concept, made of carbon-carbon refractory-composite material, has been developed that overcomes a number of the shortcomings of aluminum pistons. Carbon-carbon material, developed in the early 1960's, is lighter in weight than aluminum, has higher strength and stiffness than aluminum and maintains these properties at temperatures over 2500 F. In addition, carbon-carbon material has a low coefficient of thermal expansion and excellent resistance to thermal shock. An effort, called the Advanced Carbon-Carbon Piston Program was started in 1986 to develop and test carbon-carbon pistons for use in spark ignition engines. The carbon-carbon pistons were designed to be replacements for existing aluminum pistons, using standard piston pin assemblies and using standard rings. Carbon-carbon pistons can potentially enable engines to be more reliable, more efficient and have greater power output. By utilizing the unique characteristics of carbon-carbon material a piston can: (1) have greater resistance to structural damage caused by overheating, lean air-fuel mixture conditions and detonation; (2) be designed to be lighter than an aluminum piston thus, reducing the reciprocating mass of an engine, and (3) be operated in a higher combustion temperature environment without failure.

Sibling cycle piston and valving method

NASA Technical Reports Server (NTRS)

Mitchell, Matthew P. (Inventor); Bauwens, Luc (Inventor)

1990-01-01

A double-acting, rotating piston reciprocating in a cylinder with the motion of the piston providing the valving action of the Sibling Cycle through the medium of passages between the piston and cylinder wall. The rotating piston contains regenerators ported to the walls of the piston. The piston fits closely in the cylinder at each end of the cylinder except in areas where the wall of the cylinder is relieved to provide passages between the cylinder wall and the piston leading to the expansion and compression spaces, respectively. The piston reciprocates as it rotates. The cylinder and piston together comprise an integral valve that seqentially opens and closes the ports at the ends of the regenerators alternately allowing them to communicate with the expansion space and compression space and blocking that communication. The relieved passages in the cylinder and the ports in the piston are so arranged that each regenerator is sequentially (1) charged with compressed working gas from the compression space; (2) isolated from both expansion and compression spaces; (3) discharged of working gas into the expansion space; and (4) simultaneously charged with working gas from the expansion space while being discharged of working gas into the compression space, in the manner of the Sibling Cycle. In an alterate embodiment, heat exchangers are external to the cylinder and ports in the cylinder wall are alternately closed by the wall of the piston and opened to the expansion and compression spaces through relieved passages in the wall of the reciprocating, rotating piston.

Megawatt Class Nuclear Space Power Systems (MCNSPS) conceptual design and evaluation report. Volume 3, technologies 2: Power conversion

NASA Technical Reports Server (NTRS)

Wetch, J. R.

1988-01-01

The major power conversion concepts considered for the Megawatt Class Nuclear Space Power System (MCNSPS) are discussed. These concepts include: (1) Rankine alkali-metal-vapor turbine alternators; (2) in-core thermionic conversion; (3) Brayton gas turbine alternators; and (4) free piston Stirling engine linear alternators. Considerations important to the coupling of these four conversion alternatives to an appropriate nuclear reactor heat source are examined along with the comparative performance characteristics of the combined systems meeting MCNSPS requirements.

Electrochemistry and the Earth's Core-Mantle Boundary

NASA Astrophysics Data System (ADS)

Kavner, A.; Walker, D.

2001-12-01

The Earth's core-mantle boundary consists of a highly heterogeneous metal-oxide interface subjected to high temperatures, pressures, and additionally, to the presence of a temporally- and spatially-varying electrical field generated by the outer core dynamo. An understanding of the core-mantle boundary should include the nature of its electrical behavior, its electrically induced chemical partitioning, and any resultant core-mantle dynamic coupling. To this end, we have developed a method to measure the electrical behavior of metal-silicate interfaces at high pressures (15-25 kbar) and temperatures (1300-1400° C) in a piston-cylinder apparatus. Platinum electrical leads are placed at each end of the sample, which consists of a layer of iron and/or iron alloy below a layer of silicate. The sample is enclosed in a sintered MgO chamber which is then surrounded by a metal Faraday cage, allowing the sample to be electrically insulated from the AC field of the graphite heater. The platinum electric leads are threaded through the thermocouple tube and connected with an HP4284A LCR meter to measure AC impedance, or to a DC power supply to apply a field such that either the silicate or the metal end is the anode (+). AC impedance measurements performed in-situ on samples consisting of Fe, Fe-Ni-S, and a basalt-olivine mixture in series show that conductivity is strongly dependent on the electrical polarization of the silicate relative to the sulfide. When the silicate is positively charged (silicate is the anode) and when there is no applied charge, the probe-to-probe resistance displays semiconductor behavior, with conductivity ( ~10-2 S/cm) strongly thermally activated. However, when the electrical polarity is reversed, and the sulfide is the anode, the electrical conductivity between the two probes increases dramatically (to ~1 S/cm) over timescales of minutes. If the polarity is removed or reversed, the conductivity returns to its original values over similar timescales. A second set of experiments examined the behavior of iron-silicate interfaces subjected to electric fields of 1-10 V, applied for times ranging from several minutes to several days. The samples were quenched from high temperatures, mounted, and examined using both light and electron microscopy. When the iron/iron-sulfide end is charged positively (+1-2 V) with respect to the silicate, oxides form around the platinum electrode embedded within the iron metal, suggesting the reaction Fe->Fe+2+2e- occurs in the metal. When the electric field is reversed, the silicate and MgO surrounding the + electrode turns red, implying the reaction Fe+2\\rightarrowFe^{+3}+e^{-}$ occurs at the silicate (anode end) of the sample. The richness of electrical and electrically activated chemical behavior observed at metal-silicate interfaces may be relevant to the Earth's core mantle boundary.

[High-resolution computed tomography in stapes surgery].

PubMed

Oberascher, G; Grobovschek, M

1987-06-01

Early and delayed complications in the inner or middle ear may follow stapedectomy or stapedotomy and may require revision surgery. Nowadays high resolution middle ear computed tomography (HR-MCT) using a special interpolation technique can demonstrate the smallest structures of the middle ear space, such as the long process of the incus and stapes. Stapes prostheses can also be seen in this way, but to identify the prothesis exactly it is necessary to determine the position of the piston hook in relation to the incus and of the piston shaft to the foot plate and scala vestibuli. Two points were of particular interest to us: HR-MCT identification of various metal and plastic pistons. Clinical significance of HR-MCT in complications following surgery. As the result of our experimental research on cadaver temporal bones, pistons must still be divided into four groups based on their demonstration by HR-MCT: Group I (e.g. Stainless Steel Cup Piston): whole piston visible. Group II (e.g. McGee Stainless Steel Piston): only piston shaft. Group III (Fisch Teflon-Platinum Piston): only hook visible. Group IV (e.g. Fisch Teflon-Wire Piston): piston hardly visible or not at all. In groups I-III it is possible to discover whether the piston is too long or too short, whether it is dislocated or has slipped. Group IV pistons, hooks from group II and the shaft from group III must be changed to allow detection by x-rays. With plastic pistons it might be possible to add an x-ray agent.2+ improvements in manufacture appear to be necessary, dislocation of various prostheses can now be shown.(ABSTRACT TRUNCATED AT 250 WORDS)

Fabrication of high temperature materials by exothermic synthesis and subsequent dynamic consolidation

DOEpatents

Rabin, Barry H.; Korth, Gary E.; Wright, Richard N.; Williamson, Richard L.

1992-01-01

An apparatus for synthesizing a composite material such as titanium carbide and alumina from exothermic reaction of a sample followed by explosive induced consolidation of the reacted sample. The apparatus includes a lower base for holding a powdered composite sample, an igniter and igniter powder for igniting the sample to initiate an exothermic reaction and a piston for dynamically compressing the sample utilizing an explosive reaction.

Age Estimates of Holocene Glacial Retreat in Lapeyrère Bay, Anvers Island, Antarctica

NASA Astrophysics Data System (ADS)

Mead, K. A.; Wellner, J. S.; Rosenheim, B. E.

2011-12-01

Lapeyrère Bay is a fjord on the eastern side of Anvers Island, located off the Western Antarctic Peninsula. Anvers island has a maximum elevation of 2400m (comprised of ice overlaying bedrock), and experiences colder temperatures and more precipitation than the South Shetlands, which are ~230km to the north. Two glaciers enter Lapeyrère Bay, one large and vulnerable to avalanching, the Iliad Glacier, and one smaller glacier confined to a northern unnamed cove. Though several research cruises have visited Lapeyrère Bay, very little has been published on the fjord's glacial retreat history or sediment flux. The primary purpose of this study is to reconstruct the glacial retreat and sediment flux histories of Lapeyrère Bay using a SHALDRIL core and standard piston cores for chronology and sedimentary facies analysis, and multibeam swath bathymetry data for identifying seafloor morphological features. Preliminary core data from the proximal northern flank of Lapeyrère Bay show greenish grey sandy mud with scattered pebble and sand lens lithology. A core taken in the distal-most part of the fjord is largely diatomaceous sediment grading into grey silty mud with thin sandy turbidites. Multibeam data has exposed seafloor features including a grounding zone wedge at the entrance of the unnamed cove of northern Lapeyrère Bay, drumlins, glacial lineations, and a glacial outwash fan near the ocean-termination of the Iliad glacier. Additionally, this study seeks to assess the effectiveness of a novel 14C method of dating sediment lacking sufficient calcareous material for carbonate 14C dating. The method being tested is ramped pyrolysis radiocarbon analysis, which dates individual fractions of organic material. It is hypothesized that ramped pyrolysis will improve upon bulk acid insoluble organic material (AIOM) dating, as AIOM can include both autochthonous syndepositionally aged carbon and allochthonous pre-aged carbon, resulting in 14C ages inherently older than the age of deposition. Performing ramped pyrolysis 14C dating and carbonate 14C dating on the same cores and comparing the resulting ages will address this hypothesis. Carbonate radiocarbon dating has been completed for cores taken in the proximal fjord, from the glacial outwash fan. Four dates from a 20.3m drill core yield an average sedimentation rate of 2.2mm/yr. Four dates from the nearby 293cm gravity core yield a sedimentation rate of 1.4mm/yr. Ramped pyrolysis has been performed on a total of nine samples, six taken from the proximal drill core and three taken from the distal-most gravity core of the fjord. The average proximal sample TOC is 0.22%, and the average distal sample TOC is 0.55%. These values show a trend of increasing TOC values with increasing oceanic influence in the distal fjord.

A rapid procedure for the determination of thorium, uranium, cadmium and molybdenum in small sediment samples by inductively coupled plasma-mass spectrometry: Application in Chesapeake Bay

USGS Publications Warehouse

Zheng, Yen; Weinman, B.; Cronin, T.; Fleisher, M.Q.; Anderson, Robert F.

2003-01-01

This paper describes a rapid procedure that allows precise analysis of Mo, Cd, U and Th in sediment samples as small as 10 mg by using a novel approach that utilizes a "pseudo" isotope dilution for Th and conventional isotope dilution for Mo, Cd and U by ICP-MS. Long-term reproducibility of the method is between 2.5 and 5% with an advantage of rapid analysis on a single digestion of sediment sample and the potential of adding other elements of interest if so desired. Application of this method to two piston cores collected near the mouth of the Patuxent River in Chesapeake Bay showed that the accumulation of authigenic Mo and Cd varied in response to the changing bottom water redox conditions, with anoxia showing consistent oscillations throughout both pre-industrial and industrial times. Accumulation of authigenic U shows consistent oscillations as well, without any apparent increase in productivity related to anoxic trends. Degrees of Mo and Cd enrichment also inversely correlate to halophilic microfaunal assemblages already established as paleoclimate proxies within the bay indicating that bottom water anoxia is driven in part by the amount of freshwater discharge that the area receives. ?? 2002 Elsevier Science Ltd. All rights reserved.

Piston-Skirt Lubrication System For Compressor

NASA Technical Reports Server (NTRS)

Schroeder, Edgar C.; Burzynski, Marion, Jr.

1994-01-01

Piston-skirt lubrication system provides steady supply of oil to piston rings of gas compressor. No need for oil-filled crankcase or external oil pump. Instead, part of each piston acts as its own oil pump circulating oil from reservoir. Annular space at bottom of piston and cylinder constitutes working volume of small oil pump. Depending on application, reservoir open to atmosphere, or sealed and pressurized in bellows to prevent contact between oil and atmosphere. Filter removes particles worn away from piston rings and cylinder wall during normal operation.

Quaternary Turbidite Sedimentation in the Moresby Trough, Preliminary Observations from the Papua New Guinea S2S Study Area

NASA Astrophysics Data System (ADS)

Bentley, S. J.; Muhammad, Z.; Dickens, J.; Droxler, A.; Peterson, L.; Opdyke, B.

2004-12-01

Multicores and jumbo piston cores were collected from the Moresby Trough from the R/V Melville in March-April 204 to study patterns of off-shelf sediment flux from the Gulf of Papua to the deep sea over Pleistocene-Holocene timescales. The Moresby Trough represents the primary deep-sea sediment conduit linking the Source to Sink Gulf of Papua study area to the north with the Coral Sea Basin to the south. Core locations were navigated from the surface using dynamic positioning and multibeam bathymetric mosaics collected during the cruise. Selected cores have been analyzed using a multi-sensor core logger, X-radiography, granulometry, and Pb-210 geochronology. Most piston cores collected from the Moresby Trough contain abundant mafic sandy turbidites overlain by fine-grained hemipelagic deposits 1-2 m thick. X-radiographs of multicores reveal mostly bioturbated hemipelagics. However, one core, MV25-0403-24MC, was collected from the axis of a primary channel, and contains at least two fine-grained turbidites within the upper 0.5 m of sediment. The uppermost turbidite contains low but uniform activities of excess Pb-210, and may have been 15-20 cm thick at the time of deposition (i.e., before subsequent disruption by bioturbation), based on fabric and radiochemical evidence. Application of a simple box-model for physical mixing (i.e., during the flow) and subsequent decay suggests that the uppermost turbidite was deposited 70-120 years before present. Bioturbation has since reworked about 60% of the bed, suggesting that such beds will only escape destruction by bioturbation if they are > 10 cm thick, and are deposited more frequently than once per century. Based on these observations, we suggest that gravity flows are presently active in the Moresby trough, and may account for a significant fraction of the hemipelagic drape present in channel systems. However, fabric evidence for these thin, fine-grained beds may be obscured by subsequent bioturbation. Also, at some point in the past, possibly at the onset of the Holocene Transgression, the character of sediment flux to the Moresby Trough shifted from sandy mafic-rich sandy turbidity currents to much finer sediments, delivered downslope by both benthic flows and vertical flux through the water column.

Stirling engine with pressurized crankcase

DOEpatents

Corey, John A.

1988-01-01

A two piston Stirling engine wherein the pistons are coupled to a common crankshaft via bearing means, the pistons include pad means to minimize friction between the pistons and the cylinders during reciprocation of the pistons, means for pressurizing the engine crankcase, and means for cooling the crankshaft and the bearing means eliminating the need for oil in the crankcase.

Stabilizing Gas Bearings In Free-Piston Machines

NASA Technical Reports Server (NTRS)

Dhar, Manmohan

1995-01-01

Gas bearings and clearance seals between pistons and cylinders in free-piston machines designed to reduce undesired dynamic forces and torques on pistons, gas bearings, and cylinders. Circumferential grooves and drain galleries added to piston or cylinder in improved design. Provides stabilization without significant reduction in length of seal, or significant increase in leakage and consequent reduction of efficiency.

Reciprocating piston pump system with screw drive

NASA Technical Reports Server (NTRS)

Perkins, Gerald S. (Inventor); Moore, Nicholas R. (Inventor)

1981-01-01

A pump system of the reciprocating piston type is described, which facilitates direct motor drive and cylinder sealing. A threaded middle potion of the piston is engaged by a nut connected to rotate with the rotor of an electric motor, in a manner that minimizes loading on the rotor by the use of a coupling that transmits torque to the nut but permits it to shift axially and radially with respect to the rotor. The nut has a threaded hydrostatic bearing for engaging the threaded piston portion, with an oil-carrying groove in the nut being interrupted. A fluid emitting seal located at the entrance to each cylinder, can serve to center the piston within the cylinder, wash the piston, and to aid in sealing. The piston can have a long stroke to diameter ratio to minimize reciprocations and wear on valves at high pressures. The voltage applied to the motor can be reversed prior to the piston reaching the end of its stroke, to permit pressure on the piston to aid in reversing the motor.

Free-piston regenerative hot gas hydraulic engine

NASA Technical Reports Server (NTRS)

Beremand, D. G. (Inventor)

1980-01-01

A displacer piston which is driven pneumatically by a high-pressure or low-pressure gas is included in a free-piston regenerative hydraulic engine. Actuation of the displacer piston circulates the working fluid through a heater, a regenerator and a cooler. The present invention includes an inertial mass such as a piston or a hydraulic fluid column to effectively store and supply energy during portions of the cycle. Power is transmitted from the working fluid to a hydraulic fluid across a diaphragm or lightweight piston to achieve a hydraulic power out-put. The displacer piston of the present invention may be driven pneumatically, hydraulically or electromagnetically. In addition, the displacer piston and the inertial mass of the present invention may be positioned on the same side of the diaphragm member or may be separated by the diaphragm member.

Pulsed interrupter and method of operation

DOEpatents

Drake, Joel Lawton; Kratz, Robert

2015-06-09

Some embodiments provide interrupter systems comprising: a first electrode; a second electrode; a piston movably located at a first position and electrically coupled with the first and second electrodes establishing a closed state, the piston comprises an electrical conductor that couples with the first and second electrodes providing a conductive path; an electromagnetic launcher configured to, when activated, induce a magnetic field pulse causing the piston to move away from the electrical coupling with the first and second electrodes establishing an open circuit between the first and second electrodes; and a piston control system comprising a piston arresting system configured to control a deceleration of the piston following the movement of the piston induced by the electromagnetic launcher such that the piston is not in electrical contact with at least one of the first electrode and the second electrode when in the open state.

On the formation of vortex rings in coaxial tubes

NASA Astrophysics Data System (ADS)

Gan, Lian

2011-11-01

The formation of vortex rings within coaxial tubes of different diameter is investigated experimentally and numerically. PIV measurements were carried out in a water tank equipped with a piston-cylinder apparatus used to generate vortex rings inside a series of coaxial tubes with tube to piston diameter ratios, DT / D , ranging from 4 to 1.5. In order to distinguish between the effect confinement has on the formation of isolated vortex rings from those formed with a trailing jet flow, non- dimensional stroke ratios below and above the formation number were investigated, L / D = 2 . 5 and 10 respectively. For DT / D > 2 and L / D s below the formation number the kinematics of the vortex rings follow classical inviscid theory in so much as their self-induced velocity decreases linearly with decreasing tube diameter in accordance with the image theorem. For DT / D <= 2 boundary layer separation along the tube wall begins to interfere with the vortex during its roll-up phase. For vortex rings below the formation number, the vortex core is briefly arrested upon completion of the piston stroke. On the other hand, long L / D s give rise to even more complex dynamics. When DT / D = 2 the interaction between boundary layer and the starting jet acts to suppress vortex ring formation altogether. However, as confinement is increased further to DT / D = 1 . 5 the formation of a lead vortex ring re-appears but with a circulation lower than the formation number before rapidly decaying.

A Theoretical and Experimental Study for a Developing Flow in a Thin Fluid Gap

NASA Astrophysics Data System (ADS)

Wu, Qianhong; Lang, Ji; Jen, Kei-Peng; Nathan, Rungun; Vucbmss Team

2016-11-01

In this paper, we report a novel theoretical and experimental approach to examine a fast developing flow in a thin fluid gap. Although the phenomena are widely observed in industrial applications and biological systems, there is a lack of analytical approach that captures the instantaneous fluid response to a sudden impact. An experimental setup was developed that contains a piston instrumented with a laser displacement sensor and a pressure transducer. A sudden impact was imposed on the piston, creating a fast compaction on the thin fluid gap underneath. The motion of the piston was captured by the laser displacement sensor, and the fluid pressure build-up and relaxation was recorded by the pressure transducer. For this dynamic process, a novel analytical approach was developed. It starts with the inviscid limit when the viscous fluid effect has no time to appear. This short process is followed by a developing flow, in which the inviscid core flow region decreases and the viscous wall region increases until the entire fluid gap is filled with viscous fluid flow. A boundary layer integral method is used during the process. Lastly, the flow is completely viscous dominant featured by a typical squeeze flow in a thin gap. Excellent agreement between the theory and the experiment was achieved. The study presented herein, filling the gap in the literature, will have broad impact in industrial and biomedical applications. This research was supported by the National Science Foundation under Award #1511096.

Air riding seal for a turbine

DOEpatents

Mills, Jacob A; Brown, Wesley D; Sexton, Thomas D; Jones, Russell B

2016-07-19

An air riding seal between a rotor and a stator in a turbine of a gas turbine engine, where an annular piston is movable in an axial direction within a housing that extends from the stator, and a bellows is secured to the annular piston to form a flexible air passageway from a compressed air inlet through the annular piston and into a cushion cavity that forms an air riding seal between the annular piston and the rotor sealing surface. In another embodiment, a flexible seal secured to and extending from the annular piston forms a sealing surface between the annular piston chamber and the annular piston to provide a seal and allow for axial movement.

Surface sediment remobilization triggered by earthquakes in the Nankai forearc region

NASA Astrophysics Data System (ADS)

Okutsu, N.; Ashi, J.; Yamaguchi, A.; Irino, T.; Ikehara, K.; Kanamatsu, T.; Suganuma, Y.; Murayama, M.

2017-12-01

Submarine landslides triggered by earthquakes generate turbidity currents (e.g. Piper et al., 1988; 1999). Recently several studies report that the remobilization of the surface sediment triggered by earthquakes can also generate turbidity currents. However, studies that proposed such process are still limited (e.g. Ikehara et al., 2016; Mchugh et al., 2016; Moernaut et al., 2017). The purpose of this study is to examine those sedimentary processes in the Nankai forearc region, SW Japan using sedimentary records. We collected 46 cm-long multiple core (MC01) and a 6.7 m-long piston core (PC03) from the small basin during the R/V Shinsei Maru KS-14-8 cruise. The small confined basin, which is our study site, block the paths of direct sediment supply from river-submarine canyon system. The sampling site is located at the ENE-WSW elongated basin between the accretionary prism and the forearc basin off Kumano without direct sediment supply from river-submarine canyon system. The basin exhibits a confined basin that captures almost of sediments supplied from outside. Core samples are mainly composed of silty clay or very fine sand. Cs-137 measurement conducted on a MC01 core shows constantly high value at the upper 17 cm section and no detection below it. Moreover, the sedimentary structure is similar to fine-grained turbidite described by Stow and Shanmgam (1980), we interpret the upper 17 cm of MC01 as muddy turbidite. Grain size distribution and magnetic susceptibility also agree to this interpretation. Rapid sediment deposition after 1950 is assumed and the most likely event is the 2004 off Kii peninsula earthquakes (Mw=6.6-7.4). By calculation from extent of provenance area, which are estimated by paleocurrent analysis and bathymetric map, and thickness of turbidite layer we conclude that surface 1 cm of slope sediments may be remobilized by the 2004 earthquakes. Muddy turbidites are also identified in a PC03 core. The radiocarbon age gap of 170 years obtained around 2 mbsf of PC03 core also indicates similar sedimentary process. However, we also obtained large age gap in a thick turbidite layer, indicating remobilization of deeper sediments by landslide. Our results revealed that the studied basin recorded various scales and styles of sediment remobilizations by earthquake shakings.

MODELING SNR CASSIOPEIA A FROM THE SUPERNOVA EXPLOSION TO ITS CURRENT AGE: THE ROLE OF POST-EXPLOSION ANISOTROPIES OF EJECTA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orlando, S.; Miceli, M.; Pumo, M. L.

The remnants of core-collapse supernovae (SNe) have complex morphologies that may reflect asymmetries and structures developed during the progenitor SN explosion. Here we investigate how the morphology of the supernova remnant Cassiopeia A (Cas A) reflects the characteristics of the progenitor SN with the aim of deriving the energies and masses of the post-explosion anisotropies responsible for the observed spatial distribution of Fe and Si/S. We model the evolution of Cas A from the immediate aftermath of the progenitor SN to the three-dimensional interaction of the remnant with the surrounding medium. The post-explosion structure of the ejecta is described bymore » small-scale clumping of material and larger-scale anisotropies. The hydrodynamic multi-species simulations consider an appropriate post-explosion isotopic composition of the ejecta. The observed average expansion rate and shock velocities can be well reproduced by models with ejecta mass M {sub ej} ≈ 4 M {sub ⊙} and explosion energy E {sub SN} ≈ 2.3 × 10{sup 51} erg. The post-explosion anisotropies (pistons) reproduce the observed distributions of Fe and Si/S if they had a total mass of ≈0.25 M {sub ⊙} and a total kinetic energy of ≈1.5 × 10{sup 50} erg. The pistons produce a spatial inversion of ejecta layers at the epoch of Cas A, leading to the Si/S-rich ejecta physically interior to the Fe-rich ejecta. The pistons are also responsible for the development of the bright rings of Si/S-rich material which form at the intersection between the reverse shock and the material accumulated around the pistons during their propagation. Our result supports the idea that the bulk of asymmetries observed in Cas A are intrinsic to the explosion.« less

Low-Cost Space Structure (LCSS) Experiment. Volume I of II.

DTIC Science & Technology

1996-06-01

Cell Multiline laser - 2 100 Hold spots at BSM2 (tilts optica Tilt spots fixed offset path of (1/segment) w.r.t. 1 segment only) each other with off...Piston/Fine Piston Sensor Multiline Laser 3 Piston 1 BSM2 (pistons LEC segment w.r.t. optical path of other to 1 segment only) increase sharpness 7 LGSS...independent steering and pistoning of one beamline with respect to the other with the fixed mirror M2 and tilt/piston mirror BSM2 pair. The telescope

Gas hydrate and spatial venting variations in the continental margin offshore Southwestern Taiwan

NASA Astrophysics Data System (ADS)

Lin, S.; Lim, Y.; Hsieh, W.; Yang, T.; Wang, Y.

2006-12-01

Strong BSR, high methane contents and rapid sulfate reduction were found in the continental margin sediments offshore southwestern Taiwan. In order to identify the venting phenomena and its relationship with gas hydrate, this research investigate sea floor vent features using WHOI?|s Towcam system as well as piston core in the study region. A total of 10 dives were conducted on board the r/v OR-1. Pore water sulfate, dissolved sulfide, methane, chloride, del O18 ratio, sediment organic carbon, carbonate content and carbonate del C13 ratio, pyrite-S were measured Large spatial variations were found based on pictures obtained from Towcam system and piston cores. Active venting features include bacteria mat, live dense bivalve patches, gas plume, temperature and salinity fluctuations, rapid sulfate reduction and high concentrations of methane in sediments. In addition, vent chimney, pockmark and large authigenic carbonate buildup were also observed in the active venting area. In contrast, in some areas without active venting features, scatter dead chimney, semi- buried carbonate structures, and dead bivalves were found. Total sulfate depletion was found at depth as shallow as 1 meter below sediment water interface in area near active vent whereas almost no sulfate depletion was observed in areas without any vent feature. Stages of carbonate build up existed, with initial phase dominated by small tube, chimney, and later with massive carbonate structures protruding the sea floor. The appearances of massive carbonate buildup structures seemed to indicate the end stage of gas hydrate venting phenomena.

Piston cylinder cell for high pressure ultrasonic pulse echo measurements.

PubMed

Kepa, M W; Ridley, C J; Kamenev, K V; Huxley, A D

2016-08-01

Ultrasonic techniques such as pulse echo, vibrating reed, or resonant ultrasound spectroscopy are powerful probes not only for studying elasticity but also for investigating electronic and magnetic properties. Here, we report on the design of a high pressure ultrasonic pulse echo apparatus, based on a piston cylinder cell, with a simplified electronic setup that operates with a single coaxial cable and requires sample lengths of mm only. The design allows simultaneous measurements of ultrasonic velocities and attenuation coefficients up to a pressure of 1.5 GPa. We illustrate the performance of the cell by probing the phase diagram of a single crystal of the ferromagnetic superconductor UGe2.

Piston cylinder cell for high pressure ultrasonic pulse echo measurements

NASA Astrophysics Data System (ADS)

Kepa, M. W.; Ridley, C. J.; Kamenev, K. V.; Huxley, A. D.

2016-08-01

Ultrasonic techniques such as pulse echo, vibrating reed, or resonant ultrasound spectroscopy are powerful probes not only for studying elasticity but also for investigating electronic and magnetic properties. Here, we report on the design of a high pressure ultrasonic pulse echo apparatus, based on a piston cylinder cell, with a simplified electronic setup that operates with a single coaxial cable and requires sample lengths of mm only. The design allows simultaneous measurements of ultrasonic velocities and attenuation coefficients up to a pressure of 1.5 GPa. We illustrate the performance of the cell by probing the phase diagram of a single crystal of the ferromagnetic superconductor UGe2.

Ballistic piston fissioning plasma experiment.

NASA Technical Reports Server (NTRS)

Miller, B. E.; Schneider, R. T.; Thom, K.; Lalos, G. T.

1971-01-01

The production of fissioning uranium plasma samples such that the fission fragment stopping distance is less than the dimensions of the plasma is approached by using a ballistic piston device for the compression of uranium hexafluoride. The experimental apparatus is described. At room temperature the gun can be loaded up to 100 torr UF6 partial pressure, but at compression a thousand fold increase of pressure can be obtained at a particle density on the order of 10 to the 19th power per cu cm. Limited spectral studies of UF6 were performed while obtaining the pressure-volume data. The results obtained and their implications are discussed.

Heat flow in the western abyssal plain of the Gulf of Mexico: Implications for thermal evolution of the old oceanic lithosphere

NASA Astrophysics Data System (ADS)

Nagihara, S.; Sclater, J. G.; Phillips, J. D.; Behrens, E. W.; Lewis, T.; Lawver, L. A.; Nakamura, Y.; Garcia-Abdeslem, J.; Maxwell, A. E.

1996-02-01

The seafloor depth of an oceanic basin reflects the average temperature of the lithosphere. Thus the western abyssal plain of the Gulf of Mexico, which has tectonically subsided much (>1 km) deeper than other basins of comparable ages (late Jurassic), should be underlain by an anomalously cold lithosphere. In order to examine this hypothesis, we made suites of high-accuracy heat flow measurements at 10 sites along a line connecting Deep Sea Drilling Project (DSDP) sites 90 and 91 in the Sigsbee abyssal plain. The new heat flow sites were initially surveyed by 3.5-kHz echo sounding, 4-channel seismic reflection, seismic refraction with eight ocean bottom seismometers, and nine piston cores. We occupied a total of 48 heat flow stations along the seismic survey line (3 to 6 at each site), including 28 where we measured in situ thermal conductivities over the practical depth interval (4 m) of the new multioutrigger bow heat flow probe. We determined the heat flow associated with the lithosphere by correcting the values measured at the seafloor (41 to 45 mW/m2) for (1) the thermal effect of the sedimentation and (2) the additional heat from the radioactive elements within the sediments. The sedimentation history, required for the first, was reconstructed at each heat flow site based on ages and thicknesses of the major seismic stratigraphical sequences, age data from the DSDP cores, 3.5-kHz subbottom reflectors, and correlation of turbidite units found in the piston cores. Radiogenic heat production was measured for 55 sediment samples from four DSDP holes in the gulf, whose age ranged from present to Early Cretaceous (0.83 μW/m3 on the average). This provided the correction for the second. The effects of these two secondary factors approximately cancel one another. The lithospheric heat flow under the abyssal plain thus estimated ranges from 40 to 47 mW/m2. These heat flow values are among the lowest in the Mesozoic ocean basins where highly reliable data (45 to 55 mW/m2) have been reported. Therefore the lithosphere under the gulf seems indeed colder than that under other old ocean basins. However, it is not as cold as expected from the large tectonic subsidence. The inconsistency between the depth and heat flow may imply an anomaly in the regional thermal isostasy.

Metal/silicate partitioning of Pt and the origin of the "late veneer"

NASA Astrophysics Data System (ADS)

Ertel, W.; Walter, M. J.; Drake, M. J.; Sylvester, P. J.

2002-12-01

Highly siderophile elements (HSEs) are perfect tools for investigating core forming processes in planetary bodies due to their Fe-loving (siderophile) geochemical behavior. Tremendous scientific effort was invested into this field during the past 10 years - mostly in 1 atm experiments. However, little is known about their high-pressure geochemistry and partitioning behavior between core and mantle forming phases. This knowledge is essential to distinguish between equilibrium (Magma Ocean) and non-equilibrium (heterogeneous accretion, late veneer) models for the accretion history for the early Earth. We therefore chose to investigate the partitioning behavior of Pt up to pressures of 140 kbar (14 GPa) and temperatures of 1950°C. The used melt composition - identical to melt systems used in 1 atm experiments - is the eutectic composition of Anorthite-Diopside (AnDi), a pseudo-basalt. A series of runs were performed which were internaly buffered by the piston cylinder apparatus, and were followed by duplicate experiments buffered in the AnDi-C-CO2 system. These experiments constitute reversals since they approach equilibrium from an initially higher and lower Pt solubility (8 ppm in the non-buffered runs, and essentially Pt free in the buffered runs). Experimental charges were encapsulated in Pt capsules which served as source for Pt. Experiments up to 20 kbar were performed in a Quickpress piston cylinder apparatus, while experiments at higher pressures were performed in a Walker-type (Tucson, AZ) and a Kawai-type (Misasa, Japan) multi anvil apparatus. Time series experiments were performed in piston-cylinder runs to determine minimum run durations for the achievement of equilibrium, and to guarantee high-quality partitioning data. 6 hours was found to be sufficient to obtain equilibrium. In practice, all experiments exceeded 12 hours to assure equilibrium. In a second set of runs the temperature dependence of the partitioning behavior of Pt was investigated between the melting point of the 1 atm, AnDi system and the melting point of the Pt capsule material. Over 150 piston cylinder and 12 multi anvil experiments have been performed. Pt solubility is only slightly dependent on temperature, decreasing between 1800 and 1400°C by less than an order of magnitude. In consequence, the partitioning behavior of Pt is mostly determined by its oxygen fugacity dependence, which has only been determined in 1 atm experiments. At 10 kbar, metal/silicate partition coefficients (D's) decrease by about 3 orders of magnitude. The reason for this is not understood, but might be attributed to a first order phase transition as found for, e.g., SiO2 or H2O. Above 10 kbar any increase in pressure does not lead to any further significant decrease in partition coefficients. Solubilities stay roughly constant up to 140 kbar. Abundances of moderately siderophile elements were possibly established by metal/silicate equilibrium in a magma ocean. These results for Pt suggest that the abundances of HSEs were most probably established by the accretion of a chondritic veneer following core formation, as metal/silicate partition coefficients are too high to be consistent with metal/silicate equilibrium in a magma ocean.

Fluorocarbon seal replaces metal piston ring in low density gas environment

NASA Technical Reports Server (NTRS)

Morath, W. D.; Morgan, N. E.

1967-01-01

Reinforced fluorocarbon cupseal, which provides an integral lip-type seal, replaces the metal piston rings in piston-cylinder configurations used in the compression of low density gases. The fluorocarbon seal may be used as cryogenic compressor piston seals.

Staged combustion with piston engine and turbine engine supercharger

DOEpatents

Fischer, Larry E [Los Gatos, CA; Anderson, Brian L [Lodi, CA; O'Brien, Kevin C [San Ramon, CA

2006-05-09

A combustion engine method and system provides increased fuel efficiency and reduces polluting exhaust emissions by burning fuel in a two-stage combustion system. Fuel is combusted in a piston engine in a first stage producing piston engine exhaust gases. Fuel contained in the piston engine exhaust gases is combusted in a second stage turbine engine. Turbine engine exhaust gases are used to supercharge the piston engine.

Staged combustion with piston engine and turbine engine supercharger

DOEpatents

Fischer, Larry E [Los Gatos, CA; Anderson, Brian L [Lodi, CA; O'Brien, Kevin C [San Ramon, CA

2011-11-01

A combustion engine method and system provides increased fuel efficiency and reduces polluting exhaust emissions by burning fuel in a two-stage combustion system. Fuel is combusted in a piston engine in a first stage producing piston engine exhaust gases. Fuel contained in the piston engine exhaust gases is combusted in a second stage turbine engine. Turbine engine exhaust gases are used to supercharge the piston engine.

Multi technical analysis of wear mechanisms in axial piston pumps

NASA Astrophysics Data System (ADS)

Schuhler, G.; Jourani, A.; Bouvier, S.; Perrochat, J.-M.

2017-05-01

Axial piston pumps convert a motor rotation motion into hydraulic or pneumatic power. Their compactness and efficiency of approximately 0.9 make them suitable for actuation applications especially in aeronautics. However, they suffer a limited life due to the wear of their components. In the literature, studies of axial piston pumps deal with contact between its different elements under lubrication conditions. Nevertheless, they are more focused on analytic or numerical approaches. This study consists in an experimental analysis of worn pump components to highlight and understand wear mechanisms. Piston shoes are central components in the axial piston pump since they are involved in three tribological contacts. These three contacts are thereby studied: piston shoes/swashplate, piston shoes/pistons and piston shoes/shoes hold down plate (SHDP). To perform this analysis, helicopter hydraulic pumps after different operating times have been studied. The wear damage mechanisms and wear debris are analysed using SEM observations. 3D surface roughness measurements are then used to characterize worn surfaces. The observations reveal that in the contact between shoes and swashplate, the main wear mechanism is three-body abrasive wear due to coarse carbides removal. Between shoes and pistons, wear occurs in a less severe way and is mainly due to the debris generated in the first contact and conveyed by the lubricating fluid. In the third contact, the debris are also the prime cause of the abrasive wear and the generation of deep craters in the piston shoes.

Electrochemically-Induced Redox Reactions in Basalt at High Pressure and Temperature: An Iron and Vanadium K-edge XANES Study

NASA Astrophysics Data System (ADS)

Kavner, A.; Walker, D.; Newville, M.; Sutton, S. R.

2005-12-01

An applied electric field across a silicate sample at high pressures and temperatures in a piston cylinder apparatus can generate a wide range of oxidation states of polyvalent cations within a single experiment. If two or more polyvalent cations are included, this technique can be used to cross-calibrate oxybarometers within a single experiment. The redox state of Fe and V within a partially melted basaltic silicate was manipulated in situ in a piston-cylinder experiment with a DC power supply providing a source and sink of electrons to the sample. A 1V electrical potential differential was applied across vanadium-doped and Fe-bearing synthetic basalt samples for 24 hrs. at 20 kbar and 1400°C in a specially-designed piston cylinder sample assembly. Three experiments were performed: a control sample with no applied voltage, one with bottom cathode and top anode, and a third with top cathode and bottom anode. Synchrotron-based x-ray absorption near edge structure (XANES) spectroscopy was used to provide spot analysis of iron and vanadium oxidation states with 5μm x 5μm spatial resolution throughout the recovered samples. Systematic spatial changes of increasing oxidation states of V and Fe were observed approaching the anode. The differences in oxidation states were mapped to a corresponding local effective oxygen fugacity by comparison and extension of a calibration of vanadium oxidation states as a function of controlled oxygen fugacity from a previous study (Sutton et al., 2005, GCA, vol. 69, pp. 2333-2348). The vanadium mapping indicates that a 1V potential drop across the sample induces effective oxygen fugacity perturbations in excess of ten orders of magnitude. The presence of both Fe and V within the same sample provides a wide range of oxygen fugacity cross-calibration in these recovered samples. A relationship between oxygen fugacity and electrochemical driving force is derived. The experimental results are in good agreement with the derived relationship between applied electrochemical potential difference (the 1V in this experiment), and corresponding calculated oxygen fugacity.

Normalized inverse characterization of sound absorbing rigid porous media.

PubMed

Zieliński, Tomasz G

2015-06-01

This paper presents a methodology for the inverse characterization of sound absorbing rigid porous media, based on standard measurements of the surface acoustic impedance of a porous sample. The model parameters need to be normalized to have a robust identification procedure which fits the model-predicted impedance curves with the measured ones. Such a normalization provides a substitute set of dimensionless (normalized) parameters unambiguously related to the original model parameters. Moreover, two scaling frequencies are introduced, however, they are not additional parameters and for different, yet reasonable, assumptions of their values, the identification procedure should eventually lead to the same solution. The proposed identification technique uses measured and computed impedance curves for a porous sample not only in the standard configuration, that is, set to the rigid termination piston in an impedance tube, but also with air gaps of known thicknesses between the sample and the piston. Therefore, all necessary analytical formulas for sound propagation in double-layered media are provided. The methodology is illustrated by one numerical test and by two examples based on the experimental measurements of the acoustic impedance and absorption of porous ceramic samples of different thicknesses and a sample of polyurethane foam.

Nuclear-radiation-actuated valve. [Patent application; for increasing coolant flow to blanket

DOEpatents

Christiansen, D.W.; Schively, D.P.

1982-01-19

The present invention relates to a breeder reactor blanket fuel assembly coolant system valve which increases coolant flow to the blanket fuel assembly to minimize long-term temperature increases caused by fission of fissile fuel created from fertile fuel through operation of the breeder reactor. The valve has a valve first part (such as a valve rod with piston) and a valve second part (such as a valve tube surrounding the valve rod, with the valve tube having side slots surrounding the piston). Both valve parts have known nuclear radiation swelling characteristics. The valve's first part is positioned to receive nuclear radiation from the nuclear reactor's fuel region. The valve's second part is positioned so that its nuclear radiation induced swelling is different from that of the valve's first part. The valve's second part also is positioned so that the valve's first and second parts create a valve orifice which changes in size due to the different nuclear radiation caused swelling of the valve's first part compared to the valve's second part. The valve may be used in a nuclear reactor's core coolant system.

Two piston V-type Stirling engine

DOEpatents

Corey, John A.

1987-01-01

A two piston Stirling engine which includes a heat exchanger arrangement placing the cooler and regenerator directly adjacent the compression space for minimal cold duct volume; a sealing arrangement which eliminates the need for piston seals, crossheads and piston rods; and a simplified power control system.

Squeeze bottle apparatus with force multiplying pistons

DOEpatents

Moss, Owen R.; Gordon, Norman R.; DeFord, Henry S.; Eschbach, Eugene A.

1994-01-01

The present invention comprises a spray bottle in which the pressure resulting from the gripping force applied by the user is amplified and this increased pressure used in generating a spray such as an aerosol or fluid stream. In its preferred embodiment, the invention includes a high pressure chamber and a corresponding piston which is operative for driving fluid out of this chamber at high pressure through a spray nozzle and a low pressure chamber, and a corresponding piston which is acted upon by the hydraulic pressure within the bottle resulting from the gripping force. The low pressure chamber and piston are of larger size than the high pressure chamber and piston. The pistons are rigidly connected so that the force created by the pressure acting on the piston in the low pressure chamber is transmitted to the piston in the high pressure chamber where it is applied over a more limited area, thereby generating greater hydraulic pressure for use in forming the spray.

Spray bottle apparatus with pressure multiplying pistons

DOEpatents

Moss, Owen R.; Gordon, Norman R.; DeFord, Henry S.

1990-01-01

The present invention comprises a spray bottle in which the pressure resulting from the gripping force applied by the user is amplified and this increased pressure used in generating a spray such as an aerosol or fluid stream. In its preferred embodiment, the invention includes a high pressure chamber and a corresponding piston which is operative for driving fluid out of this chamber at high pressure through a spray nozzle and a low pressure chamber and a corresponding piston which is acted upon the hydraulic pressure within the bottle resulting from the gripping force. The low pressure chamber and piston are of larger size than the high pressure chamber and piston. The pistons are rigidly connected so that the force created by the pressure acting on the piston in the low pressure chamber is transmitted to the piston in the high pressure chamber where it is applied over a more limited area thereby generating greater hydraulic pressure for use in forming the spray.

Spray bottle apparatus with force multiply pistons

DOEpatents

Eschbach, Eugene A.

1992-01-01

The present invention comprises a spray bottle in which the pressure resulting from the gripping force applied by the user is amplified and this increased pressure used in generating a spray such as an aerosol or fluid stream. In its preferred embodiment, the invention includes a high pressure chamber and a corresponding piston which is operative for driving fluid out of this chamber at high pressure through a spray nozzle and a low pressure chamber and corresponding piston which is acted upon by the hydraulic pressure within the bottle resulting from the gripping force. The low pressure chamber and piston are of larger size than the high pressure chamber and piston. The pistons are rigidly connected so that the force created by the pressure acting on the piston in the low pressure chamber is transmitted to the piston in the high pressure chamber where it is applied over a more limited area thereby generating greater hydraulic pressure for use in forming the spray.

Open Loop Heat Pipe Radiator Having a Free-Piston for Wiping Condensed Working Fluid

NASA Technical Reports Server (NTRS)

Weinstein, Leonard M. (Inventor)

2015-01-01

An open loop heat pipe radiator comprises a radiator tube and a free-piston. The radiator tube has a first end, a second end, and a tube wall, and the tube wall has an inner surface and an outer surface. The free-piston is enclosed within the radiator tube and is capable of movement within the radiator tube between the first and second ends. The free-piston defines a first space between the free-piston, the first end, and the tube wall, and further defines a second space between the free-piston, the second end, and the tube wall. A gaseous-state working fluid, which was evaporated to remove waste heat, alternately enters the first and second spaces, and the free-piston wipes condensed working fluid from the inner surface of the tube wall as the free-piston alternately moves between the first and second ends. The condensed working fluid is then pumped back to the heat source.

Displacement front behavior of near miscible CO2 flooding in decane saturated synthetic sandstone cores revealed by magnetic resonance imaging.

PubMed

Liu, Yu; Teng, Ying; Jiang, Lanlan; Zhao, Jiafei; Zhang, Yi; Wang, Dayong; Song, Yongchen

2017-04-01

It is of great importance to study the CO 2 -oil two-phase flow characteristic and displacement front behavior in porous media, for understanding the mechanisms of CO 2 enhanced oil recovery. In this work, we carried out near miscible CO 2 flooding experiments in decane saturated synthetic sandstone cores to investigate the displacement front characteristic by using magnetic resonance imaging technique. Experiments were done in three consolidated sandstone cores with the permeabilities ranging from 80 to 450mD. The oil saturation maps and the overall oil saturation during CO 2 injections were obtained from the intensity of magnetic resonance imaging. Finally the parameters of the piston-like displacement fronts, including the front velocity and the front geometry factor (the length to width ratio) were analyzed. Experimental results showed that the near miscible vertical upward displacement is instable above the minimum miscible pressure in the synthetic sandstone cores. However, low permeability can restrain the instability to some extent. Copyright © 2016 Elsevier Inc. All rights reserved.

Time averaging and stratigraphic disorder of molluscan assemblages in the Holocene sediments in the NE Adriatic (Piran)

NASA Astrophysics Data System (ADS)

Tomasovych, Adam; Gallmetzer, Ivo; Haselmair, Alexandra; Kaufman, Darrell S.; Zuschin, Martin

2016-04-01

Stratigraphic changes in temporal resolution of fossil assemblages and the degree of their stratigraphic mixing in the Holocene deposits are of high importance in paleoecology, conservation paleobiology and paleoclimatology. However, few studies quantified downcore changes in time averaging and in stratigraphic disorder on the basis of dating of multiple shells occurring in individual stratigraphic layers. Here, we investigate downcore changes in frequency distribution of postmortem ages of the infaunal bivalve Gouldia minima in two, ~150 cm-thick piston cores (separated by more than 1 km) in the northern Adriatic Sea, close to the Slovenian city Piran at a depth of 24 m. We use radiocarbon-calibrated amino acid racemization to obtain postmortem ages of 564 shells, and quantify age-frequency distributions in 4-5 cm-thick stratigraphic intervals (with 20-30 specimens sampled per interval). Inter-quartile range for individual 4-5 cm-thick layers varies between 850 and 1,700 years, and range encompassing 95% of age data varies between 2,000 and 5,000 years in both cores. The uppermost sediments (20 cm) are age-homogenized and show that median age of shells is ~700-800 years. The interval between 20 and 90 cm shows a gradual increase in median age from ~2,000 to ~5,000 years, with maximum age ranging to ~8,000 years. However, the lowermost parts of both cores show a significant disorder, with median age of 3,100-3,300 years. This temporal disorder implies that many shells were displaced vertically by ~1 m. Absolute and proportional abundance of the bivalve Gouldia minima strongly increases towards the top of the both cores. We hypothesize that such increase in abundance, when coupled with depth-declining reworking, can explain stratigraphic disorder because numerically abundant young shells from the top of the core were more likely buried to larger sediment depths than less frequent shells at intermediate sediment depths.

Lithology and chronology of ice-sheet fluctuations (magnetic susceptibility of cores from the western Ross Sea)

NASA Technical Reports Server (NTRS)

Jennings, Anne E.

1993-01-01

The goals of the marine geology part of WAIS include reconstructing the chronology and areal extent of ice-sheet fluctuations and understanding the climatic and oceanographic influences on ice-sheet history. As an initial step toward attaining these goals, down-core volume magnetic susceptibility (MS) logs of piston cores from three N-S transects in the western Ross Sea are compared. The core transects are within separate petrographic provinces based on analyses of till composition. The provinces are thought to reflect the previous locations of ice streams on the shelf during the last glaciation. Magnetic susceptibility is a function of magnetic mineral composition, sediment texture, and sediment density. It is applied in the western Ross Sea for two purposes: (1) to determine whether MS data differentiates the three transects (i.e., flow lines), and thus can be used to make paleodrainage reconstructions of the late Wisconsinan ice sheet; and (2) to determine whether the MS data can aid in distinguishing basal till diamictons from diamictons of glacial-marine origin and thus, aid paleoenvironmental interpretations. A comparison of the combined data of cores in each transect is presented.

High-temperature gas/liquid stress relaxometers

NASA Technical Reports Server (NTRS)

Kalfayan, S. H.; Silver, R. H.

1974-01-01

Two relaxometers allow testing of elastomers in various fluids. First relaxometer uses fork-like loading spacer interposed between loading lever and support ring, so that sample is stretched predetermined amount. In second relaxometer, degree of initial elongation is set by means of adjustable collar, which, when locked in place on piston rod, enables sample to be stretched predetermined length.

Tests of oil scraper piston ring and piston fitted with oil drain holes

NASA Technical Reports Server (NTRS)

Mcdewell, H S

1922-01-01

Tests were conducted to determine whether or not a properly located and properly designed oil scraper piston ring, installed on a piston provided with oil drain holes of sufficient area, would prevent the excessive oiling of the Liberty engine, particularly with the engine running at idling speed with full oil pressure. Results showed that excessive oiling was in fact prevented. It is strongly recommended that scraper rings and pistons be adopted for aircraft engines.

Adding Some Gas Can Completely Change How an Object in a Liquid-Filled Housing Responds to Vibration

NASA Astrophysics Data System (ADS)

Torczynski, J. R.; O'Hern, T. J.; Clausen, J. R.

2015-11-01

Adding a little gas can completely change the motion of an object in a liquid-filled housing during vibration. A common system exhibiting this behavior is a spring-supported piston in a liquid-filled cylinder, where the gaps between them are narrow and depend on the piston position. When gas is absent, the piston's vibrational response is highly overdamped due to forcing viscous liquid through narrow gaps. When a small amount of gas is added, Bjerknes forces cause some of the gas to migrate below the piston. The resulting two gas regions form a pneumatic spring that enables the liquid to move with the piston, with the result that very little liquid is forced through the narrow gaps. This ``Couette mode'' has low damping and thus has a strong resonance near the frequency given by the pneumatic spring constant and the piston mass. At this frequency, the piston response is large, and the nonlinearity from the gap geometry produces a net force on the piston. This ``rectified'' force can be many times the piston's weight and can cause the piston to compress its supporting spring. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Air riding seal with purge cavity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sexton, Thomas D; Mills, Jacob A

An air riding seal for a turbine in a gas turbine engine, where an annular piston is axial moveable within an annular piston chamber formed in a stator of the turbine and forms a seal with a surface on the rotor using pressurized air that forms a cushion in a pocket of the annular piston. A purge cavity is formed on the annular piston and is connected to a purge hole that extends through the annular piston to a lower pressure region around the annular piston or through the rotor to an opposite side. The annular piston is sealed alsomore » with inner and outer seals that can be a labyrinth seal to form an additional seal than the cushion of air in the pocket to prevent the face of the air riding seal from overheating.« less

Variable delivery, fixed displacement pump

DOEpatents

Sommars, Mark F.

2001-01-01

A variable delivery, fixed displacement pump comprises a plurality of pistons reciprocated within corresponding cylinders in a cylinder block. The pistons are reciprocated by rotation of a fixed angle swash plate connected to the pistons. The pistons and cylinders cooperate to define a plurality of fluid compression chambers each have a delivery outlet. A vent port is provided from each fluid compression chamber to vent fluid therefrom during at least a portion of the reciprocal stroke of the piston. Each piston and cylinder combination cooperates to close the associated vent port during another portion of the reciprocal stroke so that fluid is then pumped through the associated delivery outlet. The delivery rate of the pump is varied by adjusting the axial position of the swash plate relative to the cylinder block, which varies the duration of the piston stroke during which the vent port is closed.

Apparatus for Sampling Surface Contamination

NASA Technical Reports Server (NTRS)

Wells, Mark

2008-01-01

An apparatus denoted a swab device has been developed as a convenient means of acquiring samples of contaminants from surfaces and suspending the samples in liquids. (Thereafter, the liquids can be dispensed, in controlled volumes, into scientific instruments for analysis of the contaminants.) The swab device is designed so as not to introduce additional contamination and to facilitate, simplify, and systematize the dispensing of controlled volumes of liquid into analytical instruments. The swab device is a single apparatus into which are combined all the equipment and materials needed for sampling surface contamination. The swab device contains disposable components stacked together on a nondisposable dispensing head. One of the disposable components is a supply cartridge holding a sufficient volume of liquid for one complete set of samples. (The liquid could be clean water or another suitable solvent, depending on the application.) This supply of liquid is sealed by Luer valves. At the beginning of a sampling process, the user tears open a sealed bag containing the supply cartridge. A tip on the nondisposable dispensing head is engaged with a Luer valve on one end of the supply cartridge and rotated, locking the supply cartridge on the dispensing head and opening the valve. The swab tip includes a fabric swab that is wiped across the surface of interest to acquire a sample. A sealed bag containing a disposable dispensing tip is then opened, and the swab tip is pushed into the dispensing tip until seated. The dispensing head contains a piston that passes through a spring-loaded lip seal. The air volume displaced by this piston forces the liquid out of the supply cartridge, over the swab, and into the dispensing tip. The piston is manually cycled to enforce oscillation of the air volume and thereby to cause water to flow to wash contaminants from the swab and cause the resulting liquid suspension of contaminants to flow into the dispensing tip. After several cycles to ensure adequate mixing, liquid containing the suspended contaminant sample is dispensed. The disposable components are then removed from the dispensing head, which may then be reused with a fresh set of disposable components.

Piston cylinder cell for high pressure ultrasonic pulse echo measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kepa, M. W., E-mail: mkepa@staffmail.ed.ac.uk; Huxley, A. D.; Ridley, C. J.

2016-08-15

Ultrasonic techniques such as pulse echo, vibrating reed, or resonant ultrasound spectroscopy are powerful probes not only for studying elasticity but also for investigating electronic and magnetic properties. Here, we report on the design of a high pressure ultrasonic pulse echo apparatus, based on a piston cylinder cell, with a simplified electronic setup that operates with a single coaxial cable and requires sample lengths of mm only. The design allows simultaneous measurements of ultrasonic velocities and attenuation coefficients up to a pressure of 1.5 GPa. We illustrate the performance of the cell by probing the phase diagram of a singlemore » crystal of the ferromagnetic superconductor UGe{sub 2}.« less

High-Resolution Holocene Records of Paleoceanographic and Paleoclimatic Variability from the Southern Alaskan Continental Margin

NASA Astrophysics Data System (ADS)

Finney, B. P.; Jaeger, J. M.; Mix, A. C.; Cowan, E. A.; Gulick, S. S.; Mayer, L. A.; Pisias, N. G.; Powell, R. D.; Prahl, F.; Stoner, J. S.

2004-12-01

We are investigating sediments from the fjords and continental margin of southern Alaska to develop high-resolution climatic and oceanographic records for the Late Quaternary. Our goal is to better understand linkages between climatic, terrestrial and oceanic systems in this tectonically active and biologically productive region. A field program was conducted aboard the R/V Maurice Ewing in August/September 2004 utilizing geophysical surveys (high-resolution swath bathymetric and backscatter imaging, shallow sub-bottom profiling, and where permitted, high-resolution seismic reflection profiling), piston and multi-coring, and CTD/water sampling at about 30 sites in this region. Cores are being analyzed for sedimentological, microfossil, geochemical and stable isotopic proxies, with chronologies constrained by Pb-210, AMS radiocarbon, tephrochronolgic and paleomagnetic dating. Our preliminary results demonstrate that these rapidly accumulating sedimentary archives can resolve environmental changes on annual to decadal timescales. Records of recent changes in lithogenic sediment accumulation and biological productivity on the Gulf of Alaska shelf track historical climatic data that extends to the early 20th century in this region. The records also correlate with multi-decadal climate regimes during the Little Ice Age as suggested by tree-ring, glacial advance and salmon abundance records from nearby coastal sites. Jack Dymond's enthusiasm for collaborative, interdisciplinary research will help guide us in unraveling the fingerprints of key processes in this relatively unexplored region.

Initial report of the IMAGES VIII/PAGE 127 gas hydrate and paleoclimate cruise on the RV Marion Dufresne in the Gulf of Mexico, 2-18 July 2002

USGS Publications Warehouse

Winters, William J.; Lorenson, T.D.; Paull, Charles K.

2007-01-01

The northern Gulf of Mexico contains many documented gas hydrate deposits near the sea floor. Although gas hydrate often is present in shallow subbottom sediment, the extent of hydrate occurrence deeper than 10 meters below sea floor in basins away from vents and other surface expressions is unknown. We obtained giant piston cores, box cores, and gravity cores and performed heat-flow analyses to study these shallow gas hydrate deposits aboard the RV Marion Dufresne in July 2002. This report presents measurements and interpretations from that cruise. Our results confirm the presence of gas hydrate in vent-related sediments near the sea bed. The presence of gas hydrate near the vents is governed by the complex interaction of regional and local factors, including heat flow, fluid flow, faults, pore-water salinity, gas concentrations, and sediment properties. However, conditions appropriate for extensive gas hydrate formation were not found away from the vents.

Initial Results from the Deep Drilling of Lake Junin, Perú

NASA Astrophysics Data System (ADS)

Rodbell, D. T.; Abbott, M. B.; Weidhaas, N.; Hatfield, R. G.; Woods, A.; Hillman, A. L.; Tapia, P. M.; Chen, C. Y.; McGee, D.; Stoner, J. S.

2016-12-01

Lake Junín (11.0°S, 76.2°W, 4085 masl) is an intermontane, high-elevation lake in the inner-tropics of the Southern Hemisphere that spans 300 km2. With a maximum water depth of 12m, Lake Junin is dammed at its northern and southern ends by alluvial fans that emanate from glacial valleys in both cordillera. These fans can be traced to moraines that are >250 ka, indicating that the lake is at least this old. During the maximum extent of late Cenozoic glaciation, glaciers reached the lake edge but at no time over the last 1 million years, or more, has Lake Junín been overridden by ice. Lake Junín is thus one of the few lakes in the tropical Andes that predates the maximum extent of glaciation and is in a geomorphic position to record the waxing and waning of alpine glaciers in nearby cordillera. Sediment cores obtained between 1980 and 1996 reveal that sediment deposited during the last glacial cycle ( 30-16 ka) is dominated by glacial flour whereas sediment deposited during the last 16 ka consists predominantly of authigenic calcite (marl) with ostracod carapaces punctuated with intervals of gyttja and peat. In July and August of 2015, piston cores were obtained from three sites in Lake Junin. Multiple overlapping cores from the deepest water site (Site 1) extend to 100 m below lake floor (mblf), and those from two shallow water, paleoglacier-proximal sites (Sites 2 and 3) extend 23 and 51 mblf, respectively. Samples acquired at 8-cm resolution from Site 1 were analyzed for total organic carbon (TOC) and total inorganic carbon [as Ca(Mg)CO3; TIC] by coulometry. Total carbon (TC) was analyzed by combusting 10 mg samples at 1000°C and quantifying the resultant CO2 by coulometry whereas TIC was analyzed by reacting 10 mg samples in 6N H3PO4 and quantifying the resultant CO2 by coulometry; TOC was determined from TOC=TC-TIC. Over the last glacial postglacial cycle (last 30 ka), mean CaCO3 and TOC concentrations in Site 1 cores are higher ( 33% and 7.4%, respectively) than those in shallow water settings ( 9.5% and 4%). Similarly, mean magnetic susceptibility (MS) is lower in Site 1 cores (6.9 SI) than in the most paleoglacier-proximal shallow water site (Site 2, 9.4 SI). Site 1 records 7 glacial and interglacial cycles whereas shallow water locations appear to be dominated by sediment deposited during the last glacial-interglacial cycle.

Improving Power Density of Free-Piston Stirling Engines

NASA Technical Reports Server (NTRS)

Briggs, Maxwell H.; Prahl, Joseph M.; Loparo, Kenneth A.

2016-01-01

Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free-piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58 percent using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a piston power increase of as much as 14 percent. Analytical predictions are compared to experimental data and show close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

Improving Power Density of Free-Piston Stirling Engines

NASA Technical Reports Server (NTRS)

Briggs, Maxwell H.; Prahl, Joseph; Loparo, Kenneth

2016-01-01

Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58 using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a maximum piston power increase of 14. Analytical predictions are compared to experimental data showing close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

Improving Free-Piston Stirling Engine Power Density

NASA Technical Reports Server (NTRS)

Briggs, Maxwell H.

2016-01-01

Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58% using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a maximum piston power increase of 14%. Analytical predictions are compared to experimental data showing close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

The Effect of Piston-Head Temperature on Knock-Limited Power

NASA Technical Reports Server (NTRS)

Imming, Harry S.

1944-01-01

To determine the effect of piston-head temperature on knock-limited power. Tests were made in a supercharged CFR engine over a range of fuel-air ratios from 0.055 to 0.120, using S-3 reference fuel, AN-F-28, Amendment-2, aviation gasoline, and AN-F-28 plus 2 percent xylidines by weight. Tests were run at a compression ratio of 7.0 with inlet-air temperatures of 150 F and 250 F and at a compression ratio of 8.0 with an inlet-air temperature of 250 F. All other engine conditions were held constant. The piston-head temperature was varied by circulation of oil through passages in the crown of a liquid-cooled piston. This method of piston cooling decreased the piston-head temperature about 80 F. The data are not intended to constitute a recommendation as to the advisability of piston cooling in practice.

Internal combustion engine for natural gas compressor operation

DOEpatents

Hagen, Christopher L.; Babbitt, Guy; Turner, Christopher; Echter, Nick; Weyer-Geigel, Kristina

2016-04-19

This application concerns systems and methods for compressing natural gas with an internal combustion engine. In a representative embodiment, a system for compressing a gas comprises a reciprocating internal combustion engine including at least one piston-cylinder assembly comprising a piston configured to travel in a cylinder and to compress gas in the cylinder in multiple compression stages. The system can further comprise a first pressure tank in fluid communication with the piston-cylinder assembly to receive compressed gas from the piston-cylinder assembly until the first pressure tank reaches a predetermined pressure, and a second pressure tank in fluid communication with the piston-cylinder assembly and the first pressure tank. The second pressure tank can be configured to receive compressed gas from the piston-cylinder assembly until the second pressure tank reaches a predetermined pressure. When the first and second pressure tanks have reached the predetermined pressures, the first pressure tank can be configured to supply gas to the piston-cylinder assembly, and the piston can be configured to compress the gas supplied by the first pressure tank such that the compressed gas flows into the second pressure tank.

Emissions of piston engine aircraft using aviation gasoline (avgas) and motor gasoline (mogas) as fuel – a review

NASA Astrophysics Data System (ADS)

Thanikasalam, K.; Rahmat, M.; Fahmi, A. G. Mohammad; Zulkifli, A. M.; Shawal, N. Noor; Ilanchelvi, K.; Ananth, M.; Elayarasan, R.

2018-05-01

There are two categories of aircraft engines, namely, piston and gas turbine engines. Piston engine extracts energy from a combustion compartment through a piston and crank apparatus that engages the propellers, which in turn, provides an aircraft the needed momentum. On the other hand, gas turbine engine heats a compressed air in the combustion compartment resulting in propulsion that drives an aircraft. Piston engine aircrafts might appear small but together thousands of piston engine aircraft, which encompasses a bulk of the general aviation fleet, present a considerable health threat. That is because these aircraft, which depend on avgas and mogas to run, comprise major remaining sources of lead emissions. People exposed to even small levels of lead, particularly children, have tendencies to suffer from cognitive and neurological harm. Dissimilar from commercial airliners that do not utilize leaded fuels, piston engine aircraft account for nearly half of the lead discharge in skies. But, what is the extent of the impact caused by these airborne emissions on the country’s economy and public health? To answer this query, a thorough literature review on emissions of piston engine aircraft ought to be undertaken. This article conducts a literature review on emissions of piston engine aircraft using avgas as fuel and mogas as fuel.

Laboratory investigation of the erosion of cohesive sediments under oscillatory flows using a synchronized imaging technique

NASA Astrophysics Data System (ADS)

Sou, I.; Calantoni, J.; Reed, A. H.; Furukawa, Y.

2012-12-01

A synchronized dual stereo particle image velocimetry (PIV) measurement technique is used to examine the erosion process of a cohesive sediment core in the Small Oscillatory Flow Tunnel (S-OFT) in the Sediment Dynamics Laboratory at the Naval Research Laboratory, Stennis Space Center, MS. The PIV system uses four cameras and a dual cavity Nd:YAG laser. The system allows for a pair of stereo PIV windows of about 10 cm by 10 cm each to be arbitrarily located within a single light sheet. Image pairs were acquired with all four cameras at 50 Hz for 50 consecutive seconds for each flow condition. The stereo PIV windows were positioned on either side of sediment cores inserted along the centerline of the S-OFT allowing for a total measurement window of about 20 cm long by 10 cm high with sub-millimeter spacing on resolved velocity vectors. The oscillatory flows are generated by two types of driving mechanism (scotch yoke and crank lever) for converting the rotational motion of the flywheel into the linear motion of a piston. The period of oscillation ranged from 2.86 to 6.12 seconds with constant semi-excursion amplitude in the test section of 9 cm. Two kinds of inorganic sediment samples were examined. One was a mixture of 50% kaolinite and 50% 500-micron sand under flows driven by the crank lever mechanism. Another sediment core was a mixture of 50% mud collected in Galveston Bay, TX, and 50% 250-micron sand under flows driven by the scotch-yoke mechanism. During the erosion process, Kelvin-Helmholtz instabilities were observed as the flow accelerated in each direction and eventually were broken down when the flow reversed. An example of the instantaneous velocity field superimposed on the raw image is shown in Figure 1. The relative concentration of suspended sediments under different flow conditions was estimated using the intensity of light scattered from the sediment particles in suspension. By subtracting the initial light scattered from the mud core, the residual light intensity was assumed to be scattered from suspended sediments eroded from the core. Relative comparisons were only made using the same sample mixture since it is difficult, if not impossible, to calibrate the light scattering from different sediments.; Figure 1. An example of the instantaneous time-resolved velocity field superimposed on the raw image.

Releasable High-Mechanical-Advantage Linear Actuator

NASA Technical Reports Server (NTRS)

Young, Gordon H.

1994-01-01

Proposed linear actuator includes ball-screw mechanism made to engage or disengage piston as needed. Requires low power to maintain release and no power to maintain engagement. Pins sliding radially in solenoids in yoke engage or disengage slot in piston. With help of optoelectronic feedback, yoke made to follow free piston during disengagement so always in position to "grab" piston.

Cooled-Spool Piston Compressor

NASA Technical Reports Server (NTRS)

Morris, Brian G.

1994-01-01

Proposed cooled-spool piston compressor driven by hydraulic power and features internal cooling of piston by flowing hydraulic fluid to limit temperature of compressed gas. Provides sufficient cooling for higher compression ratios or reactive gases. Unlike conventional piston compressors, all parts of compressed gas lie at all times within relatively short distance of cooled surface so that gas cooled more effectively.

Internal position and limit sensor for free piston machines

NASA Technical Reports Server (NTRS)

Holliday, Ezekiel S. (Inventor); Wood, James Gary (Inventor)

2012-01-01

A sensor for sensing the position of a reciprocating free piston in a free piston Stirling machine. The sensor has a disk mounted to an end face of the power piston coaxially with its cylinder and reciprocating with the piston The disk includes a rim around its outer perimeter formed of an electrically conductive material A coil is wound coaxially with the cylinder, spaced outwardly from the outer perimeter of the disk and mounted in fixed position relative to the pressure vessel, preferably on the exterior of the pressure vessel wall.

Variable compression ratio device for internal combustion engine

DOEpatents

Maloney, Ronald P.; Faletti, James J.

2004-03-23

An internal combustion engine, particularly suitable for use in a work machine, is provided with a combustion cylinder, a cylinder head at an end of the combustion cylinder and a primary piston reciprocally disposed within the combustion cylinder. The cylinder head includes a secondary cylinder and a secondary piston reciprocally disposed within the secondary cylinder. An actuator is coupled with the secondary piston for controlling the position of the secondary piston dependent upon the position of the primary piston. A communication port establishes fluid flow communication between the combustion cylinder and the secondary cylinder.

Stirling engine power control and motion conversion mechanism

DOEpatents

Marks, David T.

1983-01-01

A motion conversion device for converting between the reciprocating motion of the pistons in a Stirling engine and the rotating motion of its output shaft, and for changing the stroke and phase of the pistons, includes a lever pivoted at one end and having a cam follower at the other end. The piston rod engages the lever intermediate its ends and the cam follower engages a cam keyed to the output shaft. The lever pivot can be moved to change the length of the moment arm defined between the cam follower and the piston rod the change the piston stroke and force exerted on the cam, and the levers can be moved in opposite directions to change the phase between pistons.

Features of the gas dynamics and local heat transfer in intake system of piston engine with supercharging

NASA Astrophysics Data System (ADS)

Plotnikov, L. V.

2017-09-01

Comparison of experimental research results of gas dynamics and instantaneous local heat transfer in the intake pipes for piston internal combustion engines (ICE) without and with supercharging are presented in the article. Studies were conducted on full-scale experimental setups in terms of gas dynamic nonstationarity, which is characteristic of piston engines. It has been established that the turbocharger installation in a gas-air system of piston internal combustion engine leads to significant differences in the patterns of change in gas-dynamic and heat transfer characteristics of flows. These data can be used in a modernization of piston engines due to installation of a turbocharger or in a development of gas-air systems for piston ICE with supercharging.

Flow line sampler

DOEpatents

Nicholls, Colin I.

1992-07-14

An on-line product sampling apparatus and method for measuring product samples from a product stream (12) in a flow line (14) having a sampling aperture (11), includes a sampling tube (18) for containing product samples removed from flow line (14). A piston (22) removes product samples from the product stream (12) through the sampling aperture (11) and returns samples to product stream (12). A sensor (20) communicates with sample tube (18), and senses physical properties of samples while the samples are within sample tube (18). In one embodiment, sensor (20) comprises a hydrogen transient nuclear magnetic resonance sensor for measuring physical properties of hydrogen molecules.

The Varved Sediments of Lake Bosumtwi, Ghana and Implications for a new Chronology of West African Hydrologic Change During the Late Quaternary

NASA Astrophysics Data System (ADS)

Wheeler, C. W.; Overpeck, J. T.; Beck, J. W.; Arko, J.; Sharp, W. E.

2002-12-01

Lake Bosumtwi is a small (8-km diameter), deep (78-m) crater lake in the lowland forest of southern Ghana (West Africa) that offers tremendous potential for high-resolution environmental reconstruction. Lying in the path of the seasonal Intertropical Convergence Zone (ITCZ) monsoonal precipitation procession, as well as the dry Harmattan winds of the Sahel in winter, this lake is uniquely located to provide potential proxy records of these dominate climatic phenomena effecting West Africa's hydrologic cycle. The lake exhibits excellent sediment preservation, with finely laminated sediments through most of the ca. 24,000 years of core material recovered thus far. We present a detailed chronological analysis of the uppermost 1.1 meters of laminated sediment, obtained via a recently collected suite of freeze- and piston-cores. Utilizing digital images and petrographic thin-section transects of six freeze-cores and two piston cores, we identified 400 diagnostic marker laminations common among the cores, thus enabling cross correlation of the cores to a sub-centimeter scale. The marker laminations also serve as anchor points for counts of organic-rich fine-laminations that were hypothesized to be annual. Excellent agreement between our lamination counts and independent radiometric sediment age models (lead-210 and bomb radiocarbon) verify that these counted laminations are in fact annual (i.e. varves). Thus, we are able to present an annual chronology for the last 800 years of sedimentation (prior to 2000 AD)ñ ~4%. Though anthroprogenic changes have probably effected the local environment within the last 100 years, as we interpret anomalous increases in %organic carbon, %inorganic carbon and %nitrogen to indicate, the varve appearance does not seem to change across the 1.1 m section analyzed. Pre-nuclear weapon testing radiocarbon values, derived from bulk organic carbon, were examined in relation to the varve and lead-210 age-models to assess radiocarbon age offset due to reservoir effects and the redeposition of old-carbon; the data suggest that anomalously old radiocarbon ages ranging from ~430 to 3000 years are possible. The size of the radiocarbon bias may vary with lake status, indicating the role of old-carbon redeposition from ancient lake sediments currently at shallow depths or above current lake level in the crater catchment. Our study shows that 1) varves have excellent potential for creating a high-resolution chronology for Lake Bosumtwi, and 2) caution must be taken in using radiocarbon results to date the sediments of Lake Bosumtwi

49 CFR 230.76 - Piston travel.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Steam Locomotives and...) Maximum piston travel. The maximum piston travel when steam locomotive is standing shall be as follows...

Assessing stapes piston position using computed tomography: a cadaveric study.

PubMed

Hahn, Yoav; Diaz, Rodney; Hartman, Jonathan; Bobinski, Matthew; Brodie, Hilary

2009-02-01

Temporal bone computed tomographic (CT) scanning in the postoperative stapedotomy patient is inaccurate in assessing stapes piston position within the vestibule. Poststapedotomy patients that have persistent vertigo may undergo CT scanning to assess the position of the stapes piston within the vestibule to rule out overly deep insertion. Vertigo is a recognized complication of the deep piston, and CT evaluation is often recommended. The accuracy of CT scan in this setting is unestablished. Stapedotomy was performed on 12 cadaver ears, and stainless steel McGee pistons were placed. The cadaver heads were then scanned using a fine-cut temporal bone protocol. Temporal bone dissection was performed with microscopic measurement of the piston depth in the vestibule. These values were compared with depth of intravestibular penetration measured on CT scan by 4 independent measurements. The intravestibular penetration as assessed by computed tomography was consistently greater than the value found on cadaveric anatomic dissection. The radiographic bias was greater when piston location within the vestibule was shallower. The axial CT scan measurement was 0.53 mm greater, on average, than the anatomic measurement. On average, the coronal CT measurement was 0.68 mm greater than the anatomic measurement. The degree of overestimation of penetration, however, was highly inconsistent. Standard temporal bone CT scan is neither an accurate nor precise examination of stapes piston depth within the vestibule. We found that CT measurement consistently overstated intravestibular piston depth. Computed tomography is not a useful study in the evaluation of piston depth for poststapedectomy vertigo and is of limited value in this setting.

Gas-enabled resonance and rectified motion of a piston in a vibrated housing filled with a viscous liquid

DOE PAGES

Romero, Louis A.; Torczynski, John R.; Clausen, Jonathan R.; ...

2015-11-16

Herein, we show how introducing a small amount of gas can completely change the motion of a solid object in a viscous liquid during vibration. We analyze an idealized system exhibiting this behavior: a piston moving in a liquid-filled housing, where the gaps between the piston and the housing are narrow and depend on the piston position. Recent experiments have shown that vibration causes some gas to move below the piston and the piston to subsequently move downward and compress its supporting spring. Herein, we analyze the analogous but simpler situation in which the gas regions are replaced by bellowsmore » with similar pressure-volume relationships. We show that these bellows form a spring (analogous to the pneumatic spring formed by the gas regions) which enables the piston and the liquid to oscillate in a mode that does not exist without this spring. This mode is referred to here as the Couette mode because the liquid in the gaps moves essentially in Couette flow (i.e., with almost no component of Poiseuille flow). Since Couette flow by itself produces extremely low damping, the Couette mode has a strong resonance. We show that, near this resonance, the dependence of the gap geometry on the piston position produces a large rectified (net) force on the piston during vibration. As a result, this force can be much larger than the piston weight and the strength of its supporting spring and is in the direction that decreases the flow resistance of the gap geometry.« less

Casting Apparatus Including A Gas Driven Molten Metal Injector And Method

DOEpatents

Trudel, David R.; Meyer, Thomas N.; Kinosz, Michael J.; Arnaud, Guy; Bigler, Nicolas

2003-06-17

The filtering molten metal injector system includes a holder furnace, a casting mold supported above the holder furnace, and at least one molten metal injector supported from a bottom side of the casting mold. The holder furnace contains a supply of molten metal. The mold defines a mold cavity for receiving the molten metal from the holder furnace. The molten metal injector projects into the holder furnace. The molten metal injector includes a cylinder defining a piston cavity housing a reciprocating piston for pumping the molten metal upward from the holder furnace to the mold cavity. The cylinder and piston are at least partially submerged in the molten metal when the holder furnace contains the molten metal. The cylinder or the piston includes a molten metal intake for receiving the molten metal into the piston cavity when the holder furnace contains molten metal. A conduit connects the piston cavity to the mold cavity. A molten metal filter is located in the conduit for filtering the molten metal passing through the conduit during the reciprocating movement of the piston. The molten metal intake may be a valve connected to the cylinder, a gap formed between the piston and an open end of the cylinder, an aperture defined in the sidewall of the cylinder, or a ball check valve incorporated into the piston. A second molten metal filter preferably covers the molten metal intake to the injector.

Gas-lubricated seal for sealing between a piston and a cylinder wall

DOEpatents

Hoult, David P.

1985-01-01

A piston-cylinder seal uses gas for a lubricant and has a runner supported on a gapless structure and placed in the space between the piston and the cylinder wall. The runner is deformed elastically under the influence of the operating pressures to follow and compensate for variations in the piston-cylinder fit and maintain a seal.

Gas-lubricated seal for sealing between a piston and a cylinder wall

DOEpatents

Hoult, D.P.

1985-09-10

A piston-cylinder seal uses gas for a lubricant and has a runner supported on a gapless structure and placed in the space between the piston and the cylinder wall. The runner is deformed elastically under the influence of the operating pressures to follow and compensate for variations in the piston-cylinder fit and maintain a seal. 4 figs.

Hot piston ring/cylinder liner materials: Selection and evaluation

NASA Technical Reports Server (NTRS)

Sliney, Harold E.

1988-01-01

In current designs of the automotive (kinematic) Stirling engine, the piston rings are made of a reinforced polymer and are located below the pistons because they cannot withstand the high temperatures in the upper cylinder area. Theoretically, efficiency could be improved if hot piston rings were located near the top of the pistons. Described is a program to select piston ring and cylinder coating materials to test this theory. Candidate materials were screened, then subjected to a pin or disk friction and wear test machine. Tests were performed in hydrogen at specimen temperatures up to 760 C to simulate environmental conditions in the region of the hot piston ring reversal. Based on the results of these tests, a cobalt based alloy, Stellite 6B, was chosen for the piston rings and PS200, which consists of a metal-bonded chromium carbide matrix with dispersed solid lubricants, was chosen as the cylinder coating. Tests of a modified engine and a baseline engine showed that the hot ring reduced specific fuel consumption by up to 7 percent for some operating conditions and averaged about 3 percent for all conditions evaluated. Related applications of high-temperature coatings for shaft seals and as back-up lubricants are also described.

Improved engine performance via use of nickel ceramic composite coatings (NCC coat)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Funatani, K.; Kurosawa, K.; Fabiyi, P.A.

1994-09-01

In seeking to produce lightweight aluminum block based engines, a variety of metallurgical and surface modification techniques for cylinder bores, pistons and piston rings are available. This paper discusses these various alternative methods while placing particular emphasis on electroplated nickel ceramic composite coatings (NCC). NCC Coating properties are characterized by high hardness, high corrosion resistance, high temperature wear and scuff resistance and low frictional coefficients. The application of NCC Coatings in 2-stroke motorcycle and diesel engines has resulted in benefits in the following areas: elimination of cast iron liners; reduced cylinder wall temperature, engine weight and increased power; lowering ofmore » oil consumption; improved fuel economy; reduction in emissions; improved scuff and wear resistance on cylinder bores, pistons and piston rings; friction reduction; combating of piston ring groove microwelding and pound out; thermal barrier protection on diesel piston domes; reduction in carbon deposition on piston domes; reduced noise from piston slap; and ability to operate in corrosive environments. The sum of the above stated benefits holds much potential for contributing towards greater flexibility in materials selection for the design of lightweight, fuel efficient vehicles based upon the use of aluminum engines. 13 refs., 13 figs.« less

Comparison of free-piston Stirling engine model predictions with RE1000 engine test data

NASA Technical Reports Server (NTRS)

Tew, R. C., Jr.

1984-01-01

Predictions of a free-piston Stirling engine model are compared with RE1000 engine test data taken at NASA-Lewis Research Center. The model validation and the engine testing are being done under a joint interagency agreement between the Department of Energy's Oak Ridge National Laboratory and NASA-Lewis. A kinematic code developed at Lewis was upgraded to permit simulation of free-piston engine performance; it was further upgraded and modified at Lewis and is currently being validated. The model predicts engine performance by numerical integration of equations for each control volume in the working space. Piston motions are determined by numerical integration of the force balance on each piston or can be specified as Fourier series. In addition, the model Fourier analyzes the various piston forces to permit the construction of phasor force diagrams. The paper compares predicted and experimental values of power and efficiency and shows phasor force diagrams for the RE1000 engine displacer and piston. Further development plans for the model are also discussed.

Piston Ring Pressure Distribution

NASA Technical Reports Server (NTRS)

Kuhn, M.

1943-01-01

The discovery and introduction of the internal combustion engine has resulted in a very rapid development in machines utilizing the action of a piston. Design has been limited by the internal components of the engine, which has been subjected to ever increasing thermal and mechanical stresses, Of these internal engine components, the piston and piston rings are of particular importance and the momentary position of engine development is not seldom dependent upon the development of both of the components, The piston ring is a well-known component and has been used in its present shape in the steam engine of the last century, Corresponding to its importance, the piston ring has been a rich field for creative activity and it is noteworthy that in spite of this the ring has maintained its shape through the many years. From the many and complicated designs which have been suggested as a packing between piston and cylinder wall hardly one suggestion has remained which does not resemble the original design of cast iron rectangular ring.

Measuring Pressure Has a New Standard

NASA Technical Reports Server (NTRS)

2002-01-01

The Force-Balanced Piston Gauge (FPG) tests and calibrates instrumentation operating in the low pressure range. The system provides a traceable, primary calibration standard for measuring pressures in the range of near 0 to 15 kPa (2.2 psi) in both gauge and absolute measurement modes. The hardware combines a large area piston-cylinder with a load cell measuring the force resulting from pressures across the piston. The mass of the piston can be tared out, allowing measurement to start from zero. A pressure higher than the measured pressure, which keeps the piston centered, lubricates an innovative conical gap located between the piston and the cylinder, eliminating the need for piston rotation. A pressure controller based on the control of low gas flow automates the pressure control. DHI markets the FPG as an automated primary standard for very low-gauge and absolute pressures. DHI is selling the FPG to high-end metrology laboratories on a case by case basis, with a full commercial release to follow.

The formation of quasi-parallel shocks. [in space, solar and astrophysical plasmas

NASA Technical Reports Server (NTRS)

Cargill, Peter J.

1991-01-01

In a collisionless plasma, the coupling between a piston and the plasma must take place through either laminar or turbulent electromagnetic fields. Of the three types of coupling (laminar, Larmor and turbulent), shock formation in the parallel regime is dominated by the latter and in the quasi-parallel regime by a combination of all three, depending on the piston. In the quasi-perpendicular regime, there is usually a good separation between piston and shock. This is not true in the quasi-parallel and parallel regime. Hybrid numerical simulations for hot plasma pistons indicate that when the electrons are hot, a shock forms, but does not cleanly decouple from the piston. For hot ion pistons, no shock forms in the parallel limit: in the quasi-parallel case, a shock forms, but there is severe contamination from hot piston ions. These results suggest that the properties of solar and astrophysical shocks, such as particle acceleration, cannot be readily separated from their driving mechanism.

Estimation of sediment friction coefficient from heating upon APC penetration during the IODP NanTroSEIZE

NASA Astrophysics Data System (ADS)

Kinoshita, M.; Kawamura, K.; Lin, W.

2015-12-01

During the Nankai Trough Seismogenic Zone Experiments (NanTroSEIZE) of the Integrated Ocean Drilling Program (IODP), the advanced piston corer temperature (APC-T) tool was used to determine in situ formation temperatures while piston coring down to ~200 m below sea floor. When the corer is fired into the formation, temperature around the shoe abruptly increases due to the frictional heating. The temperature rise due to the frictional heat at the time of penetration is 10 K or larger. We found that the frictional temperature rise (=maximum temperature) increases with increasing depth, and that its intersection at the seafloor seems non-zero. Frictional heat energy is proportional to the maximum temperature rise, which is confirmed by a FEM numerical simulation of 2D cylindrical system. Here we use the result of numerical simulation to convert the observed temperature rise into the frictional heat energy. The frictional heat energy is represented as the product of the shooting length D and the shear stress (τ) between the pipe and the sediment. Assuming a coulomb slip regime, the shear stress is shows as: τ= τ0 + μ*(Sv-Pp), where τ0 is the cohesive stress, μ the dynamic frictional coefficient between the pipe and the sediment, Sv the normal stress at the pipe, and Pp the pore pressure. This can explain the non-zero intersection as well as depth-dependent increase for the frictional heating observed in the APC-T data. Assuming a hydrostatic state and by using the downhole bulk density data, we estimated the friction coefficient for each APC-T measurement. For comparison, we used the vane-shear strength measured on core samples to estimate the friction coefficients. The frictional coefficients μ were estimated as ranging 0.01 - 0.06, anomalously lower than expected for shallow marine sediments. They were lower than those estimated from vane-shear data, which range 0.05 to 0.2. Still, both estimates exhibit a significant increase in the friction coefficient at Site C0012, which dominates in the hemipelagic sediment in the Shikoku Basin. The anomalously low values suggest either fluid injection between the pipe and the sediment during the measurement, or some other uncertainties in converting the observed temperature rise to the frictional heat generation.

Carbonate Deposition on Antarctic Shelves

NASA Astrophysics Data System (ADS)

Frank, T. D.; James, N. P.; Malcolm, I.

2011-12-01

Limestones associated with glaciomarine deposits occur throughout the geologic record but remain poorly understood. The best-described examples formed during major ice ages of the Neoproterozoic and Late Paleozoic. Quaternary analogs on Antarctic shelves have received comparatively little study. Here, we report on the composition, spatial distribution, and stratigraphic context of carbonate sediments contained in piston cores from the Ross Sea. The goals of this work are to (1) document the nature and distribution of carbonate sediments on the Ross Sea continental shelf and (2) examine temporal relationships to Quaternary glaciation. Results will be used to develop criteria that will improve understanding of analogous deposits in the ancient record. All carbonate-rich intervals in piston cores from the Ross Rea, now housed at the Antarctic Marine Geology Research Facility at Florida State University, were examined and described in detail. Sediment samples were disaggregated and sieved into size fractions before description with paleontological analysis carried out on the coarsest size fraction (>250 microns). Carbonate-rich sediments are concentrated in the northwestern Ross Sea, along the distal margins of Mawson and Pennell Banks. Calcareous facies include a spectrum of lithologies that range from fossiliferous mud, sand, and gravel to skeletal floatstone-rudstone and bafflestone. Floatstone-rudstone and bafflestone is most abundant along western-facing slopes in areas protected from the Antarctic Coastal Current. Sand-prone facies dominate the tops of banks and mud-prone, often spicultic, facies occur in deeper areas. The carbonate factory is characterized by a low-diversity, heterozoan assemblage that is dominated by stylasterine hydrocorals, barnacles, and bryozoans. Molluscs and echinoids are present but not abundant. Planktic and benthic foraminifera are ubiquitous components of the sediment matrix, which is locally very rich in sponge spicules. Biota rarely occur in growth position. Rather, there is much evidence of postdepositional reworking so that these carbonates accumulate as clastic sediments. Available radiocarbon ages place deposition during the transition from MIS 3 to MIS 2, during a time of glacial expansion. Accumulation ceased during the Last Glacial Maximum and so calcareous sediments in the Ross Sea are restricted in both time and space. Deposition occured during windows of time when subdued siliciclastic input and high trophic resource availablity combined to create conditions that favor cold-water carbonate production. Results provide a context for interpreting older carbonates recovered in drillcores from more proximal regions of the Ross Sea.

Unsteady response of flow system around balance piston in a rocket pump

NASA Astrophysics Data System (ADS)

Kawasaki, S.; Shimura, T.; Uchiumi, M.; Hayashi, M.; Matsui, J.

2013-03-01

In the rocket engine turbopump, a self-balancing type of axial thrust balancing system using a balance piston is often applied. In this study, the balancing system in liquid-hydrogen (LH2) rocket pump was modeled combining the mechanical structure and the flow system, and the unsteady response of the balance piston was investigated. The axial vibration characteristics of the balance piston with a large amplitude were determined, sweeping the frequency of the pressure fluctuation on the inlet of the balance piston. This vibration was significantly affected by the compressibility of LH2.

Free-piston cutting machine

DOEpatents

Ciccarelli, Gaby; Subudhi, Manomohan; Hall, Robert E.

2000-01-01

A cutting machine includes a gun barrel for receiving a projectile. A compression tube is disposed in flow communication with the barrel and includes a piston therein. A reservoir is disposed in flow communication with the tube and receives a first gas under pressure. A second gas fills the compression tube on a front face of the piston. And, the pressurized first gas is discharged into the tube on a back face of the piston to accelerate the piston through the tube for compressing the second gas, and in turn launching the projectile through the barrel to impact a workpiece.

A Visual Photographic Study of Cylinder Lubrication

NASA Technical Reports Server (NTRS)

Shaw, Milton C; Nussdorfer, Theodore

1946-01-01

A V-type engine provided with a glass cylinder was used to study visually the lubrication characteristics of an aircraft-type piston. Photographs and data were obtained with the engine motored at engine speeds up to 1000 r.p.m. and constant cylinder-head pressures of 0 and 50 pounds per square inch. A study was made of the orientation of the piston under various operating conditions, which indicated that the piston was inclined with the crown nearest the major-thrust cylinder face throughout the greater part of the cycle. The piston moved laterally in the cylinder under the influence of piston side thrust.

Floating air riding seal for a turbine

DOEpatents

Ebert, Todd A

2016-08-16

A floating air riding seal for a gas turbine engine with a rotor and a stator, an annular piston chamber with an axial moveable annular piston assembly within the annular piston chamber formed in the stator, an annular cavity formed on the annular piston assembly that faces a seal surface on the rotor, where the axial moveable annular piston includes an inlet scoop on a side opposite to the annular cavity that scoops up the swirling cooling air and directs the cooling air to the annular cavity to form an air cushion with the seal surface of the rotor.

Propellant Expulsion in Unmanned Spacecraft

DTIC Science & Technology

1966-07-01

29 19. Experimental WAC Corporal piston tank .. ......... . 33 20. Three piston tank designs used in the Corporal program ..... 34 21...propellant. The only universal F. Filling seal at this writing is a metal bellows. Usually, piston tank assemblies are filled by a vacuum technique...externally gener- Piston tank assemblies are subjected to essentially the ated loads due to shock and vibration may be the sever- same tests as bladders. 31

Advanced General Aviation Turbine Engine (GATE) study

NASA Technical Reports Server (NTRS)

Smith, R.; Benstein, E. H.

1979-01-01

The small engine technology requirements suitable for general aviation service in the 1987 to 1988 time frame were defined. The market analysis showed potential United States engines sales of 31,500 per year providing that the turbine engine sales price approaches current reciprocating engine prices. An optimum engine design was prepared for four categories of fixed wing aircraft and for rotary wing applications. A common core approach was derived from the optimum engines that maximizes engine commonality over the power spectrum with a projected price competitive with reciprocating piston engines. The advanced technology features reduced engine cost, approximately 50 percent compared with current technology.

Evidence for submarine landslides and continental slope erosion related to fault reactivation during the last glaciation offshore eastern Canada

NASA Astrophysics Data System (ADS)

Saint-Ange, F.; Campbell, C.; MacKillop, K.; Mosher, D. C.; Piper, D. J.; Roger, J.

2012-12-01

Many studies have proposed that reactivation of dormant faults during deglaciation is a source of neotectonic activity in glaciated regions, but few have demonstrated the relationship to submarine landslides. In this study, seabed morphology and shallow geology of the outer continental margin adjacent to the Charlie Gibbs Fracture Zone off Newfoundland, Canada was investigated for evidence of this relationship. The glacial history and morphology of the margin suggest that the entire continental shelf in the area, coincident with major continental crustal lineaments, was ice-covered during the Last glacial cycle, and transverse troughs delineate the paleo-icestream drainage patterns. A recent investigation of Notre Dame Trough revealed the existence of large sediment failures on the shelf. The current study investigates complex seafloor erosion and widespread mass transport deposition (MTD) on the continental slope seaward of Notre Dame Trough, using recently-acquired high resolution seismic reflection data and piston cores. The new data reveal that a trough mouth fan (TMF) is present on the slope seaward of Notre Dame Trough. The Notre Dame TMF is characterized by a succession of stacked debris flows, but does not show a lobate shape in plan view like other classic TMFs. Instead, the Notre Dame TMF has abruptly-truncated margins suggesting post-depositional failure and erosion of the fan deposits. Seismic reflection data show that the locations of the failures along the TMF margin are coincident with a set of shallow faults; however the current dataset does not image the deeper portion of the faults. On the upper slope immediately south of the TMF, a narrow and deeply incised canyon is located along-trend with the Notre Dame Trough. The location of this canyon appears to be controlled by a fault. Downslope from this canyon, along the southern margin of the TMF, a 25 km wide, flat-floored, U-shaped valley was eroded into a succession of stacked MTD-filled channels. Seismic stratigraphic analysis shows that the valley developed around the same time as the adjacent TMF, however, the valley morphology and evidence for repeated slope failure suggests that the processes responsible for its formation were different than the processes that formed the nearby TMF. Age control provided from piston cores suggest that the last major slope failure that contributed to valley formation probably occurred at ~29 ka. Geotechnical measurements from piston cores show slightly underconsolidated sediments. The results indicate that this part of the margin is more unstable than Orphan Basin and Labrador slope regions. Given the low factor of safety and the complex fault system, low energy earthquake from the surrounding area could be enough to potentially trigger landslides.

Tectonic and Sedimentation Interactions in the East Caribbean Subduction Zone: AN Overview from the Orinoco Delta to the Barbados Accretionary Prism

NASA Astrophysics Data System (ADS)

Deville, E.

2011-12-01

Recent marine geophysical acquisitions and piston-coring allow to better understand the close interactions between the sand-rich Orinoco turbidite system and the compressional structures of the Barbados prism. Because of the morphologic and tectonic control in the east-Caribbean active margin, the Orinoco turbiditic pattern system does not exhibit a classic fan geometry. The sea-floor geometry between the slope of the front of the Barbados prism and the slope of the South-American margin induces the convergence of the turbidite channels toward the abyssal plain, at the front of the accretionary prism. Also, whereas in most passive margins the turbidite systems are organized upstream to downstream as canyon, then channel-levee, then lobes, here, due to the tectonic control, the sedimentary system is organized as channel-levee, then canyons, then channelized lobes. At the edge of the Orinoco platform, the system has multiple sources with several distributaries and downward the channel courses are complex with frequent convergences or divergences that are emphasized by the effects of the undulating seafloor tectonic morphologies associated with active thrust tectonics and mud volcanism. On top of the accretionary prism, turbidite sediments are filling transported piggy-back basins whose timing of sedimentation vs. deformation is complex. Erosion processes are almost absent on the highly subsiding Orinoco platform and in the upper part of the turbidite system. Erosion processes develop mostly between 2000 and 4000 m of water depth, above the compressional structures of the Barbados prism (canyons up to 3 km wide and 300 m deep). In the abyssal plain, turbiditic channels develop on very long distance (> 1000 km) joining the mid-Atlantic channel (sourced mostly by the Amazon), filling several elongated basins corresponding to transform faults (notably the Barracuda Basin), and finally sourcing the Puerto-Rico trench, the deepest morphologic depression of this region. Piston-core surveys have demonstrated that turbidite sediments above the accretionary prism and in the abyssal plain are mostly coarse sandy deposits covered by recent pelagic planktonic-rich sediments, which indicate that sand deposition has slow down during the post-glacial sea level rise. Numerical stratigraphic modeling suggests that during the last glacial event, the main depocenters were located above the tectonic prism and in the abyssal plain, at the front of the prism and that, during the Holocene eustatic rise, a large accommodation space formed on the shelf confining sedimentation mostly on the Orinoco deltaic platform and producing a starvation downstream in the turbidite system. This is in good agreement with the piston coring results which show low deep turbidite sedimentation rates during recent times.

Effect of piston profile on performance and emission characteristics of a GDI engine with split injection strategy - A CFD study

NASA Astrophysics Data System (ADS)

Karaya, Y.; Mallikarjuna, J. M.

2017-09-01

Gasoline direct injection (GDI) engines have gained popularity in the recent times because of lower fuel consumption and exhaust emissions. But in these engines, the mixture preparation plays an important role which affects combustion, performance and emission characteristics. The mixture preparation in turn depends mainly upon combustion chamber geometry. Therefore, in this study, an attempt has been made to understand the effect of piston profile on the performance and emission characteristics in a GDI engine. The analysis is carried out on a four-stroke wall guided GDI engine using computational fluid dynamics (CFD). The spray breakup model used is validated with the available experimental results from the literature to the extent possible. The analysis is carried out for four piston profiles viz., offset pentroof with offset bowl (OPOB), flat piston with offset bowl (FPOB), offset pentroof with offset scoop (OPOS) and inclined piston with offset bowl (IPOB) fitted in an engine equipped with a six-hole injector with the split injection ratio of 30:70. All the CFD simulations are carried out at the engine speed of 2000 rev/min., with the overall equivalence ratio of about 0.65±0.05. The performance and emission characteristics of the engine are compared while using the above piston profiles. It is found that, the OPOB piston is preferred compared to that of the other pistons because it has better in-cylinder flow, IMEP and lower HC emissions compared to that of other pistons.

Durability, Performance, and Emission of Diesel Engines Using Carbon Fiber Piston and Liner

NASA Technical Reports Server (NTRS)

Afify, E. M.; Roberts, W. L.

1999-01-01

This report summarizes the research conducted by NC State University in investigating the durability, performance and emission of a carbon fiber piston and liner in our single cylinder research Diesel engine. Both the piston and liner were supplied to NC State University by NASA LaRC and manufactured by C-CAT under a separate contract to NASA LaRC. The carbon-carbon material used to manufacture the piston and liner has significantly lower thermal conductivity, coefficient of thermal expansion, and superior strength characteristics at elevated temperatures when compared to conventional piston materials such as aluminum. The results of the carbon-carbon fiber piston testing were compared to a baseline configuration, which used a conventional aluminum piston in a steel liner. The parameters measured were the brake specific fuel consumption, ignition delay, frictional horsepower, volumetric efficiency, and durability characteristics of the two pistons. Testing was performed using a naturally aspirated Labeco Direct Injection single cylinder diesel engine. Two test cases were performed over a range of loads and speeds. The fixed test condition between the aluminum and carbon-carbon piston configurations was the brake mean effective pressure. The measured data was the fuel consumption rate, volumetric efficiency, load, speed, cylinder pressure, needle lift, and exhaust gas temperature. The cylinder pressure, and fuel consumption, exhaust gas temperature, and needle lift were recorded using a National Instruments DAQ board and a PC. All test cases used Diesel no. 2 for fuel.

Distribution of clay minerals on the Alaskan margin near Barrow Canyon revealed by Diffuse Spectral Reflectance measurements

NASA Astrophysics Data System (ADS)

Orsburn, C.; Ortiz, J. D.; Polyak, L.; Grebmeier, J. M.; Darby, D.

2007-12-01

Sediment clay mineral assemblages provide an excellent means of assessing the provenance of Arctic sediment due to the variety of sediment transport mechanisms at work and the existence of distinct weathering sources from differing bedrock geology. During HOTRAX Leg 1 aboard the USCG Ice breaker Healy (cruise HLY0501), we collected jumbo piston cores on the Alaskan margin near Barrow Canyon which provide detailed Holocene sedimentary records. Measurements of Diffuse Spectral Reflectance (DSR) were collected at 1cm resolution from the split surface of the cores using a Minolta CM-2600d UV/VIS spectrophotometer (400-700nm wavelength range; 10nm resolution; 3mm spot size). To interpret the resulting downcore records, we present a preliminary study using 28 coretop sediment samples collected by the Shelf-Basin Interaction program in 2004 arrayed in four transects across the shelf near Barrow Canyon. The samples were analyzed using an ASD Labspec Pro FR UV/VIS/NIR spectrometer (250-2500nm wavelength range, 2-10nm resolution; 20mm spot size). Our results indicate that the measurements from the two instruments are offset by constant factors, but can be easily compared. To estimate the clay mineralogy of the cores, we decomposed the matrix of DSR measurements from the coretop and downcore samples using principle component analysis and compared the resulting factor score patterns with mineral diffuse spectral reflectance signatures from known samples measured in our lab or available from version 5 of the USGS Digital Spectral Library. The three leading modes extracted by principle component analysis of the downcore samples are applicable to the coretops. We infer that the first principle component mode relates to smectite, the second to chlorite, and the third to a mixture of illite and goethite (herein referred to as illite - goethite). The geographic and bathymetric trends in the coretop data indicate that (1) the smectite and illite - goethite components both increase with depth and reach greater values in the two western transects than in the two eastern transects closest to the coast and Barrow Canyon, (2) the smectite and illite- goethite components are anticorrelated in the two western transects, but not in the two eastern transects, (3) chlorite decreases with depth and is highest in the two transects closest to Barrow Canyon. These results suggest that the chlorite on the Alaskan margin is transported by nearshore currents from the Bering Straight and then by bottom currents flowing through the Barrow Canyon. Accordingly, we interpret downcore chlorite peaks inferred from DSR measurements in our sediment cores as evidence of times of enhanced input of Pacific water to the Alaskan Margin.

High-resolution sub-bottom seismic and sediment core records from the Chukchi Abyssal Plain reveal Quaternary glaciation impacts on the western Arctic Ocean

NASA Astrophysics Data System (ADS)

Joe, Y. J.; Seokhoon, Y.; Nam, S. I.; Polyak, L.; Niessen, F.

2017-12-01

For regional context of the Quaternary history of Arctic marine glaciations, such as glacial events in northern North America and on the Siberian and Chukchi margins, we used CHIRP sub-bottom profiles (SBP) along with sediment cores, including a 14-m long piston core ARA06-04JPC taken from the Chukchi abyssal plain during the RV Araon expedition in 2015. Based on core correlation with earlier developed Arctic Ocean stratigraphies using distribution of various sedimentary proxies, core 04JPC is estimated to extend to at least Marine Isotope Stage 13 (>0.5 Ma). The stratigraphy developed for SBP lines from the Chukchi abyssal plain to surrounding slopes can be divided into four major seismostratigraphic units (SSU 1-4). SBP records from the abyssal plain show well preserved stratification, whereas on the surrounding slopes this pattern is disrupted by lens-shaped, acoustically transparent sedimentary bodies interpreted as glaciogenic debris flow deposits. Based on the integration of sediment physical property and SBP data, we conclude that these debris flows were generated during several ice-sheet grounding events on the Chukchi and East Siberian margins, including adjacent ridges and plateaus, during the middle to late Quaternary.

HYDRAULIC SERVO

DOEpatents

Wiegand, D.E.

1962-05-01

A hydraulic servo is designed in which a small pressure difference produced at two orifices by an electrically operated flapper arm in a constantly flowing hydraulic loop is hydraulically amplified by two constant flow pumps, two additional orifices, and three unconnected ball pistons. Two of the pistons are of one size and operate against the additional orifices, and the third piston is of a different size and operates between and against the first two pistons. (AEC)

Improving Free-Piston Stirling Engine Specific Power

NASA Technical Reports Server (NTRS)

Briggs, Maxwell Henry

2014-01-01

This work uses analytical methods to demonstrate the potential benefits of optimizing piston and/or displacer motion in a Stirling Engine. Isothermal analysis was used to show the potential benefits of ideal motion in ideal Stirling engines. Nodal analysis is used to show that ideal piston and displacer waveforms are not optimal in real Stirling engines. Constrained optimization was used to identify piston and displacer waveforms that increase Stirling engine specific power.

Improving Free-Piston Stirling Engine Specific Power

NASA Technical Reports Server (NTRS)

Briggs, Maxwell H.

2015-01-01

This work uses analytical methods to demonstrate the potential benefits of optimizing piston and/or displacer motion in a Stirling engine. Isothermal analysis was used to show the potential benefits of ideal motion in ideal Stirling engines. Nodal analysis is used to show that ideal piston and displacer waveforms are not optimal in real Stirling engines. Constrained optimization was used to identify piston and displacer waveforms that increase Stirling engine specific power.

Optimum step design for centering of pistons moving in an incompressible fluid

NASA Technical Reports Server (NTRS)

Etsion, I.; Hamrock, B. J.

1976-01-01

Hydrodynamic effects are analyzed for a stepped piston moving within a tight clearance tube filled with an incompressible fluid. Hydrostatic effects are analyzed and a complete solution is obtained and an optimum step design for centering of the piston is suggested. The axial speed resulting from an axial driving force is calculated, and some experimental results for pistons falling in a water-filled tube are presented.

Dynamically balanced, hydraulically driven compressor/pump apparatus for resonant free piston Stirling engines

DOEpatents

Corey, John A.

1984-05-29

A compressor, pump, or alternator apparatus is designed for use with a resonant free piston Stirling engine so as to isolate apparatus fluid from the periodically pressurized working fluid of the Stirling engine. The apparatus housing has a first side closed by a power coupling flexible diaphragm (the engine working member) and a second side closed by a flexible diaphragm gas spring. A reciprocally movable piston is disposed in a transverse cylinder in the housing and moves substantially at right angles relative to the flexible diaphragms. An incompressible fluid fills the housing which is divided into two separate chambers by suitable ports. One chamber provides fluid coupling between the power diaphragm of the RFPSE and the piston and the second chamber provides fluid coupling between the gas spring diaphragm and the opposite side of the piston. The working members of a gas compressor, pump, or alternator are driven by the piston. Sealing and wearing parts of the apparatus are mounted at the external ends of the transverse cylinder in a double acting arrangement for accessibility. An annular counterweight is mounted externally of the reciprocally movable piston and is driven by incompressible fluid coupling in a direction opposite to the piston so as to damp out transverse vibrations.

Recent Development of the Two-Stroke Engine. II - Design Features. 2; Design Features

NASA Technical Reports Server (NTRS)

Zeman, J.

1945-01-01

Completing the first paper dealing with charging methods and arrangements, the present paper discusses the design forms of two-stroke engines. Features which largely influence piston running are: (a) The shape and surface condition of the sliding parts. (b) The cylinder and piston materials. (c) Heat conditions in the piston, and lubrication. There is little essential difference between four-stroke and two-stroke engines with ordinary pistons. In large engines, for example, are always found separately cast or welded frames in which the stresses are taken up by tie rods. Twin piston and timing piston engines often differ from this design. Examples can be found in many engines of German or foreign make. Their methods of operation will be dealt with in the third part of the present paper, which also includes the bibliography. The development of two-stroke engine design is, of course, mainly concerned with such features as are inherently difficult to master; that is, the piston barrel and the design of the gudgeon pin bearing. Designers of four-stroke engines now-a-days experience approximately the same difficulties, since heat stresses have increased to the point of influencing conditions in the piston barrel. Features which notably affect this are: (a) The material. (b) Prevailing heat conditions.

Geothermal expansion spool piston

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reed, L. T.

1985-08-06

A packing supporting piston assembly removably securable to an end section of a production casing of a geothermal well, which end section is disposed above a well head. The piston assembly when so mounted has packing in abutting sealing contact with the end section of the production casing and also has packing that is in slidable sealing contact with the interior surface of the expansion spool. The piston assembly is of such structure that the pressures exerted by the packing on the end section of the casing and on the interior surface of the expansion spool are independently adjustable tomore » desired magnitudes. The degree of pressure exerted by the packing on the interior surface of the expansion spool is adjustable after the packing has been disposed within the confines of the spool. The piston assembly in a preferred form includes a circumferentially extending high temperature resisting grease seal situated within the confines of the piston assembly. In addition to the preferred form of the piston assembly, alternate forms of the piston assembly are provided, each of which permits the pressure exerted by the packing on the interior surface of the expansion spool to be adjusted to a desired magnitude and periodically varied as the same becomes necessary to maintain an effective seal.« less

Apparatus and method for delivering a fluid to a container

DOEpatents

Turner, Terry D.

2002-01-01

An apparatus for delivering a fluid into a container has a carriage movably associated with a holding mechanism along an axis. A piston is attached to the carriage and a cylinder is slidably attached to the piston along the axis. The cylinder has a hole formed therein that extends along the axis. A needle extending along the axis is attached to the piston and passes through the cylinder hole. The needle has a first operative position relative to the piston when the needle is retracted within the cylinder and a second operative position relative to the piston when the needle extends from the cylinder.

Piezoelectric and Electrostrictive Materials for Transducer Applications.

DTIC Science & Technology

1984-05-01

the stress is applied to sample using a simple lever arm to provide high load at the center point of a piston of hardened steel. To avoid poisson ratio...relatively simple ’screening test’ for PZT powders, powder samples were prepared from six different PZT transducer formulations supplied by the Navy...to 6000C showed the largest broadening. Heat treatment of this sample to 1.1000C reduced the broadening markedly indicating that simple chemical co

Nonlinear Dynamics of a Spring-Supported Piston in a Vibrated Liquid-Filled Housing: II. Experiments

NASA Astrophysics Data System (ADS)

O'Hern, T. J.; Torczynski, J. R.; Clausen, J. R.

2016-11-01

The nonlinear dynamics of a piston supported by a spring in a vibrated liquid-filled housing is investigated experimentally. The housing containing the piston and the liquid is subjected to vibrations along its axis. A post fixed to the housing penetrates a hole through the piston and produces a flow resistance that depends on piston position. Flexible bellows attached to the housing ends enable the piston, liquid, and bellows to execute a collective motion that forces little liquid through the flow resistance. The low damping of this motion leads to a resonance, at which the flow-resistance nonlinearity produces a net force on the piston that can cause it to compress its spring. Experiments are performed to investigate the nonlinear dynamics of this system, and these results are compared to theoretical and numerical results. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Simultaneous piston position and tilt angle sensing for large vertical displacement micromirrors by frequency detection inductive sensing

NASA Astrophysics Data System (ADS)

Tseng, V. F.-G.; Xie, H.

2015-11-01

This paper presents a frequency detection based inductive eddy current sensing mechanism to simultaneously sense the piston position and tilt angle of the mirror plate of large vertical displacement micromirrors that exhibit piston scan ranges above 100 μm. This is accomplished by sensing the inductance change, and thus resonant frequency shift, of two microfabricated sensing coils packaged underneath the mirror plate. For demonstration purpose, the coils were paired with discrete circuit components to oscillate at 11.9 MHz and 12.5 MHz, respectively. The piston position and tilt angle of the mirror plate could be simultaneously monitored over a 500 μm piston scan range, achieving a maximum piston sensitivity of 4.15 kHz/μm with a piston sensing resolution of 96 nm and a maximum tilt angle sensitivity of 60.5 kHz/° with a tilt angle sensing resolution of 0.0013°. Analytical modeling of the coil inductance change via image theory was also conducted, showing that the sensor sensitivity and resolution could be improved by increasing the coil oscillation frequency and decreasing the coil size.

Composition of Sediment Inputs to the Hikurangi Subduction Margin: A Prelude to IODP Expedition 375

NASA Astrophysics Data System (ADS)

Underwood, M.

2017-12-01

Expedition 375 of the International Ocean Discovery Program is scheduled to begin drilling offshore New Zealand in March 2018. Two sites will be cored seaward of the Hikurangi subduction front (subduction inputs), plus one site at the toe of the accretionary prism, and one site in the forearc above a zone of well-documented slow-slip events. One of the challenges during planning for Expedition 375 has been the total absence of pre-existing compositional data from the region; that lack of basic information impacts such tasks as mixing and analysis of appropriate standards for X-ray diffraction, error analysis, computation of accurate normalization factors, and QA/QC. To help overcome those deficiencies, I analyzed a total of 152 samples from ODP Sites 1123 (Quaternary to Eocene), 1124 (Quaternary to Cretaceous), and 1125 (Quaternary to Miocene), plus piston/gravity-core samples from the repositories at Lamont-Doherty, Oregon State, and NIWA. The results reveal an unusually large range of compositions for the bulk sediments. The relative abundance of total clay minerals ranges from 3 to 64 wt%. Quartz ranges from 0 to 39 wt%. Feldspar ranges from 0 to 40 wt%, and calcite ranges from 0 to 93 wt%. Samples from the Hikurangi Plateau and Chatham Rise are carbonate-rich, with many bordering on almost-pure nannofossil chalk. Hemipelagic muds from the floor of Hikurangi Trough, Ruatoria slide, and the landward slope of the trench are fairly uniform, with averages of 36 wt% total clay minerals, 27 wt% quartz, 24 wt% feldspar, and 13 wt% calcite. Unlike many other subduction zones, this diversity of lithologies will save shipboard scientists from repetitive, mind-numbing descriptions and analyses, and shorebased experiments for frictional properties, permeability, and consolidation will need to pay close attention to the compositional attributes of the specimens. In addition, results from the four IODP boreholes can be interpreted within a broader, regional-scale framework of sediment provenance and dispersal.

Stirling cycle engine

DOEpatents

Lundholm, Gunnar

1983-01-01

In a Stirling cycle engine having a plurality of working gas charges separated by pistons reciprocating in cylinders, the total gas content is minimized and the mean pressure equalization among the serial cylinders is improved by using two piston rings axially spaced at least as much as the piston stroke and by providing a duct in the cylinder wall opening in the space between the two piston rings and leading to a source of minimum or maximum working gas pressure.

Piston flow in a two-dimensional channel

NASA Astrophysics Data System (ADS)

Katopodes, Fotini V.; Davis, A. M. J.; Stone, H. A.

2000-05-01

A solution using biorthogonal eigenfunctions is presented for viscous flow caused by a piston in a two-dimensional channel. The resulting infinite set of linear equations is solved using Spence's optimal weighting function method [IMA J. Appl. Math. 30, 107 (1983)]. The solution is compared to that with a shear-free piston surface; in the latter configuration the fluid more rapidly approaches the Poiseuille flow profile established away from the face of the piston.

Low Differential Pressure Generator

NASA Technical Reports Server (NTRS)

Stout, Stephen J. (Inventor); Deyoe, Richard T. (Inventor)

1997-01-01

A method and apparatus for evaluating low differential pressure transducers includes a pressure generator in the form of a piston-cylinder assembly having a piston that may be manually positioned precisely within the cylinder to change the volume and thus the pressure at respective sides of the piston. At one side of the piston the cylinder communicates with a first chamber and at the other side of the piston the cylinder communicates with a second chamber, the first and second chambers being formed within a common tank by a partition wall. The chambers each communicate with the transducer to be evaluated and a standard pre-calibrated transducer the transducers being connected fluidly in parallel so that a pressure differential between air in the two chambers resulting from movement of the piston within the cylinder is communicated to both the transducer to be evaluated and the standard transducer, and the outputs of the transducers is observed and recorded.

Variable displacement blower

DOEpatents

Bookout, Charles C.; Stotts, Robert E.; Waring, Douglass R.; Folsom, Lawrence R.

1986-01-01

A blower having a stationary casing for rotatably supporting a rotor assembly having a series of open ended chambers arranged to close against the surrounding walls of the casing. Pistons are slidably mounted within each chamber with the center of rotation of the pistons being offset in regard to the center of rotation of the rotor assembly whereby the pistons reciprocate in the chambers as the rotor assembly turns. As inlet port communicates with the rotor assembly to deliver a working substance into the chamber as the pistons approach a top dead center position in the chamber while an outlet port also communicates with the rotor to exhaust the working substance as the pistons approach a bottom dead center position. The displacement of the blower is varied by adjusting the amount of eccentricity between the center of rotation of the pistons and the center of rotation of the rotor assembly.

Free piston inertia compressor

DOEpatents

Richards, W.D.C.; Bilodeau, D.; Marusak, T.; Dutram, L. Jr.; Brady, J.

A free piston inertia compressor comprises a piston assembly including a connecting rod having pistons on both ends, the cylinder being split into two substantially identical portions by a seal through which the connecting rod passes. Vents in the cylinder wall are provided near the seal to permit gas to escape the cylinder until the piston covers the vent whereupon the remaining gas in the cylinder functions as a gas spring and cushions the piston against impact on the seal. The connecting rod has a central portion of relatively small diameter providing free play of the connecting rod through the seal and end portions of relatively large diameter providing a limited tolerance between the connecting rod and the seal. Finally, the seal comprises a seal ring assembly consisting of a dampener plate, a free floating seal at the center of the dampener plate and a seal retainer plate in one face of the dampener plate.

Free piston inertia compressor

DOEpatents

Richards, William D. C.; Bilodeau, Denis; Marusak, Thomas; Dutram, Jr., Leonard; Brady, Joseph

1981-01-01

A free piston inertia compressor comprises a piston assembly including a connecting rod having pistons on both ends, the cylinder being split into two substantially identical portions by a seal through which the connecting rod passes. Vents in the cylinder wall are provided near the seal to permit gas to excape the cylinder until the piston covers the vent whereupon the remaining gas in the cylinder functions as a gas spring and cushions the piston against impact on the seal. The connecting rod has a central portion of relatively small diameter providing free play of the connecting rod through the seal and end portions of relatively large diameter providing a limited tolerance between the connecting rod and the seal. Finally, the seal comprises a seal ring assembly consisting of a dampener plate, a free floating seal at the center of the dampener plate and a seal retainer plate in one face of the dampener plate.

The Holocene Record of the Arctic Oscillation and a Possible Link to Solar Variability

NASA Astrophysics Data System (ADS)

Rand, J.; Darby, D. A.; Ortiz, J.; Cook, M. Y.; Keigwin, L.

2007-12-01

Detailed Fe grain provenance for a 19.9 meter long piston core (HLY02-JPC16) with about 17.5 m of Holocene sediment provides a sub-century scale resolution of the Arctic Oscillation (AO). The presence of Fe grains matched to Russian shelves fluctuates throughout this core, located 125 km north of Alaska in 1300 m water depth. High amounts of these Fe grains indicate a strong positive AO. While century scale fluctuations occur in the influx of Russian ice-rafted grains at this core site, a significant periodicity of about 1500 years exists that is similar to that of Be-10 in the Greenland ice cores. This begs the question as to how the AO might be linked to solar variations, especially such weak ones. The sources of sea ice rafting throughout the Holocene are compared to Modern sea ice samples and there is generally a good match. There is much greater heterogeneity in sources based on Fe grain provenance than other techniques for sourcing sea ice today. While the Laptev Sea is certainly an important sea ice entrainment area, it is by no means the only one and not even the most important over the long term. This distinction lies with northern Canadian sources, especially the Queen Elizabeth Islands facing the Arctic Ocean. The AO plays a major role in mixing sea ice from Russian and North American sources, especially during ++AO events. At these times, not only does the Trans Polar Drift swing closer to North America introducing sea ice from the Russian shelves such as the Laptev Sea to the Beaufort Gyre (BG), but it also aids in dragging some of the BG ice toward Fram Strait. This BG ice is a mix of North American and Russian ice and thus it is not surprising to find sediment from both sources in ice along the drift path of this ice moving toward Fram Strait.

Geological Characteristics of Active Methane Expulsion In Accretionary Prism Kaoping Slope Off SW Taiwan

NASA Astrophysics Data System (ADS)

Huang, C.; Chien, C.; Yang, T. F.; Lin, S.

2005-12-01

The Kaoping Slope off SW Taiwan represents the syn-collision accretionary prism characterized by active NW-trending folding - thrusting structures and high sedimentation rate favoring the formation of gas hydrate. For an assessment of gas hydrate potential in the Kaoping Slope off SW Taiwan, sedimentology, paleontology and geochemistry in box cores and piston cores were studied. BSRs are commonly found in seismic profiles in 400-600 m below seafloor of water depth 2500-1000 m. Active expulsions of methane were found along active thrust faults where sulfate/methane interface could be as shallow as 30 cm and the methane concentration of dissolved gases in bottom water and in pore-space of drilled core samples could be three-four order higher than the normal marine environments. Occurrences of authigenic carbonate and elongated pyrite tubes are correlated with shallow SMI depth and high methane content in bottom water and pore-space of sediment cores. Authigenic carbonates were found in seafloor surface and in 20-25 meters below seafloor. The authigenic carbonate nodules are characterized by irregular shape, whitish color, no visible microfossil, containing native sulfur, pyrites, gypsum, small open spaces, and very depleted carbon isotope (-54 ~ -43 per mil PDB). Tiny native sulfur and gypsum crystals were commonly found either on surface of foraminiferal tests and elongated pyrite tubes or in the authigenic carbonate nodules. Morphological measurements of elongated pyrite tubes show that they could represent pseudomorphs after three types of Pogonophora tube worm. Foraminifers are commonly filled by rhomboidal pyrites or cemented by pyrite crystals. Normal marine benthic foraminifers predominated by calcareous tests of slope fauna are associated with authigenic carbonate nodules in the study area, suggesting no major geochemistry effect on distribution of benthic foraminifers. Integrating sedimentology, paleontology and geochemistry characters, there could be high potential to have gas hydrate in the accretionary prism off SW Taiwan.

The influence of nitrogen ion implantation on the tribological properties of piston rings made of Hardox and Raex steels

NASA Astrophysics Data System (ADS)

Budzyński, P.; Kamiński, M.; Pyszniak, K.

2016-09-01

The implantation of nitrogen, carbon, and oxygen can be used for enhancing the tribological properties of critical components for internal combustion engines. Hardox and Raex steels have very similar strength parameters as for steel used for piston rings in internal combustion engines. An essential criterion when selecting material for the production of piston rings is a low friction factor and a low wear index. The aim of this study was to determine the extent to which these parameters can be enhanced by nitrogen ion implantation. Samples were implanted with nitrogen ions with 65 keV energy and the fluence of implanted ions set to 1.1017 N + /cm2. Friction and wear measurements were performed on a pin-on disc stand. The results demonstrate that implantation with nitrogen ions significantly reduces the friction factor and wear of Hardox 450 and Raex 400 steels. Implantation can and should be used for enhancing the tribological properties of steel used for friction elements in internal combustion engines, particularly when heat treatment is excluded. Final elements can be subjected to implantation, as the process does not change their dimensions.

Experimental approach for thermal parameters estimation during glass forming process

NASA Astrophysics Data System (ADS)

Abdulhay, B.; Bourouga, B.; Alzetto, F.; Challita, C.

2016-10-01

In this paper, an experimental device designed and developedto estimate thermal conditions at the Glass / piston contact interface is presented. This deviceis made of two parts: the upper part contains the piston made of metal and a heating device to raise the temperature of the piston up to 500 °C. The lower part is composed of a lead crucible and a glass sample. The assembly is provided with a heating system, an induction furnace of 6 kW for heating the glass up to 950 °C.The developed experimental procedure has permitted in a previous published study to estimate the Thermal Contact ResistanceTCR using the inverse technique developed by Beck [1]. The semi-transparent character of the glass has been taken into account by an additional radiative heat flux and an equivalent thermal conductivity. After the set-up tests, reproducibility experiments for a specific contact pressure have been carried outwith a maximum dispersion that doesn't exceed 6%. Then, experiments under different conditions for a specific glass forming process regarding the application (Packaging, Buildings and Automobile) were carried out. The objective is to determine, experimentallyfor each application,the typical conditions capable to minimize the glass temperature loss during the glass forming process.

Unmelted Meteoritic Debris Collected from Eltanin Ejecta in Polarstern Cores from Expedition ANT XII/4

NASA Technical Reports Server (NTRS)

Kyte, Frank T.

2002-01-01

A total of 1.7g of unmelted meteorite particles have been recovered from FS Polarstern piston cores collected on expedition ANT XII/4 that contain ejecta from the Eltanin impact event. Most of the mass (1.2 g) is a large, single specimen that is a polymict breccia, similar in mineralogy and chemistry to howardites or the silicate fraction of mesosiderites. Most of the remaining mass is in several large individual pieces (20-75mg each) that are polymict breccias, fragments dominated by pyroxene, and an igneous rock fragment. The latter has highly fractionated REE, similar to those reported in mafic clasts from mesosiderites. Other types of specimens identified include fragments dominated by maskelynite or olivine. These pieces of the projectile probably survived impact by being blown off the back surface of the Eltanin asteroid during its impact into the Bellingshausen Sea.

A Gas Pressure Scale Based on Primary Standard Piston Gauges

PubMed Central

Olson, Douglas A.; Driver, R. Greg; Bowers, Walter J.

2010-01-01

The National Institute of Standards and Technology (NIST) has redefined its gas pressure scale, up to 17 MPa, based on two primary standard piston gauges. The primary standard piston gauges are 35.8 mm in diameter and operate from 20 kPa to 1 MPa. Ten secondary standard piston gauges, two each of five series of the Ruska 2465 type, with successively smaller diameters form the scale extending up to 17 MPa. Six of the piston gauges were directly compared to the primary standards to determine their effective area and expanded (k = 2) uncertainty. Two piston gauges operating to 7 MPa were compared to the 1.4 MPa gauges, and two piston gauges operating to 17 MPa were compared to the 7 MPa gauges. Distortion in the 7 MPa piston gauges was determined by comparing those gauges to a DH Instruments PG7601 type piston gauge, whose distortion was calculated using elasticity theory. The relative standard uncertainties achieved by the primary standards range from 3.0 × 10−6 to 3.2 × 10−6. The relative standard uncertainty of the secondary standards is as low as 4.2 × 10−6 at 300 kPa. The effective areas and uncertainties were validated by comparison to standards of other National Metrology Institutes (NMIs). Results show agreement in all cases to better than the expanded (k = 2) uncertainty of the difference between NIST and the other NMIs, and in most cases to better than the standard (k = 1) uncertainty of the difference. PMID:27134793

Collapsible pistons for light-gas guns

NASA Technical Reports Server (NTRS)

Teng, R. N.

1973-01-01

Moving and expandable parts of gun consist of pump-tube diaphragm, piston, launch-tube diaphragm, and saboted projectile. As a result of improved piston design, pressure cycle has been significantly improved by smoother buildup, increasing muzzle velocities up to 50%.

Liquid-metal-piston MHD generator

NASA Technical Reports Server (NTRS)

Palmer, J. P.

1969-01-01

Magnetohydrodynamic generator uses a slug or piston of liquid potassium as the working fluid. An expanding vapor of the metal is allowed to reciprocate the liquid-metal-piston through a magnetic field and the expansion energy is converted directly into electrical energy.

Experimental determination of the Mo isotope fractionation factor between metal and silicate liquids

NASA Astrophysics Data System (ADS)

Hin, R. C.; Burkhardt, C.; Schmidt, M. W.; Bourdon, B.

2011-12-01

The conditions and chemical consequences of core formation have mainly been reconstructed from experimentally determined element partition coefficients between metal and silicate liquids. However, first order questions such as the mode of core formation or the nature of the light element(s) in the Earth's core are still debated [1]. In addition, the geocentric design of most experimental studies leaves the conditions of core formation on other terrestrial planets and asteroids even more uncertain than for Earth. Through mass spectrometry, records of mass-dependent stable isotope fractionation during high-temperature processes such as metal-silicate segregation are detectable. Stable isotope fractionation may thus yield additional constrains on core formation conditions and its consequences for the chemical evolution of planetary objects. Experimental investigations of equilibrium mass-dependent stable isotope fractionation have shown that Si isotopes fractionate between metal and silicate liquids at temperatures of 1800°C and pressures of 1 GPa, while Fe isotopes leave no resolvable traces of core formation processes [2,3]. Molybdenum is a refractory and siderophile trace element in the Earth, and thus much less prone to complications arising from mass balancing core and mantle and from potential volatile behaviour than other elements. To determine equilibrium mass-dependent Mo isotope fractionation during metal-silicate segregation, we have designed piston cylinder experiments with a basaltic silicate composition and an iron based metal with ~8 wt% Mo, using both graphite and MgO capsules. Metal and silicate phases are completely segregated by the use of a centrifuging piston cylinder at ETH Zurich, thus preventing analysis of mixed metal and silicate signatures. Molybdenum isotope compositions were measured using a Nu Instruments 1700 MC-ICP-MS at ETH Zurich. To ensure an accurate correction of analytical mass fractionation a 100Mo-97Mo double spike was admixed before chemical purification. Initial results provide an equilibrium 98Mo/95Mo isotope fractionation factor between metal and silicate liquids of -0.18±0.10% (2σ) at 1400°C and 1 GPa. Although the relative mass difference of these Mo isotopes is smaller than for Fe isotopes, this result implies that metal-silicate segregation may have led to mass-dependent stable Mo isotope fractionation, as opposed to Fe isotopes. A possible explanation is that the bonding environment of Mo may counterbalance its relatively small mass separation. At reducing conditions, Mo occurs in 4+ valence state in silicates [4] and thus its bond strength difference between metal and silicate may be more similar to that of Si than Fe. Stable Mo isotopes may thus become an important tool for constraining the conditions of core formation in asteroids and terrestrial planets. [1] Rubie et al. (2011) EPSL 301, 31-42. [2] Shahar et al. (2009) EPSL 288, 228-234. [3] Poitrasson et al. (2009) EPSL 278, 376-385. [4] Farges et al. (2006) Can. Min. 44, 731-753.

Holocene sedimentary processes in the Gemlik Gulf: a transtensional basin on the middle Strand of the North Anatolian Fault, Sea of Marmara

NASA Astrophysics Data System (ADS)

Özmaral, A.; Çagatay, M. N.; Imren, C.; Gasperini, L.; Henry, P.

2012-04-01

Gemlik Gulf is an oval-shaped transtensional basin with a maximum depth of 113 m, located on the middle strand of the North Anatolian Fault (NAF) in the eastern part of the Sea of Marmara (SOM). During the last glacial period until the Holocene marine transgression about 12 ka BP, the sea level was below the Çanakkale (Dardanelles) Strait's bedrock sill depth of -85 m, and the Gemlik Basin became a lake isolated lake from the rest of the Sea of Marmara "Lake" and the global ocean. The high resolution seismic profiles and the multi- beam bathymetric map of the basin show that the basin is characterized by NW-SE trending transtensional oblique faults, delta lobes of the Büyükdere (Kocadere) to the east and an erosional surface below an up to 15 m-thick Holocene mud drape. The Holocene mud drape was studied in up to 9.5 m-long gravity-piston and 0.84 m-long sediment/water interface cores located at -105 to -113 m in the basin's depocentre. The Holocene mud consists mainly of plastic gray green marine clayey mud that includes thick-red brown clay layers and a laminated organic-rich, dark olive green sapropel in the lower part, which was previously dated at 11.6-6.4 14Ckyr (uncalib) BP. Multi-proxy analyses of the Holocene mud drape in the sediment cores were carried out using Multisensor Core Logger, XRF Core Scanner equipped with digital X-Ray radiography, and laser particle size analyzer. Seismic-core correlation was made using seismic data of the chirp profiles at the core locations and the synthetic seismograms generated using the MSCL P-wave velocity and gamma density measurements. The long piston-gravity cores include five 20 to 100 mm-thick "red brown mud layers" in the top 2.5 m of the core. These layers have a sharp basal boundary and gradational upper boundary. The red brown layers consist of 55-75% clay-size material with an average grain size of 3-4 µm, and have relatively a high magnetic susceptibility. They are enriched in K, Fe, Ti and Zr that are the proxy of detrital mineral input, and depleted in Ca, Br, Fe and Mn. Manganese shows a sharp enrichment immediately below the base of the red brown layers. All these features strongly suggest that the red layers represent the distal edges mass flow deposits, possibly sourced from the delta to the east. The distinct Mn enrichments below the base of the red brown layers represent the diagenetic enrichment at the oxic/anoxic boundary near the seafloor, which was later covered by the mass flow deposit. C-14 and radionuclide datings of the mass flow layers and investigation of their possible relation to the past earthquakes are under progress.

Solid state engine with alternating motion

DOEpatents

Golestaneh, Ahmad A.

1982-01-01

Heat energy is converted to mechanical motion utilizing apparatus including a cylinder, a piston having openings therein reciprocable in the cylinder, inlet and outlet ports for warm water at one end of the cylinder, inlet and outlet ports for cool water at the other end of the cylinder, gates movable with the piston and slidably engaging the cylinder wall to alternately open and close the warm and cool water ports, a spring bearing against the warm water side of the piston and a double helix of a thermal shape memory material attached to the cool end of the cylinder and to the piston. The piston is caused to reciprocate by alternately admitting cool water and warm water to the cylinder.

Solid state engine with alternating motion

DOEpatents

Golestaneh, A.A.

1980-01-21

Heat energy is converted to mechanical motion utilizing apparatus including a cylinder, a piston having openings therein reciprocable in the cylinder, inlet and outlet ports for warm water at one end of the cylinder, inlet and outlet ports for cool water at the other end of the cylinder, gates movable with the piston and slidably engaging the cylinder wall to alternately open and close the warm and cool water ports, a spring bearing against the warm water side of the piston and a double helix of a thermal shape memory material attached to the cool end of the cylinder and to the piston. The piston is caused to reciprocate by alternately admitting cool water and warm water to the cylinder.

REACTOR CONTROL

DOEpatents

Fortescue, P.; Nicoll, D.

1962-04-24

A control system employed with a high pressure gas cooled reactor in which a control rod is positioned for upward and downward movement into the neutron field from a position beneath the reactor is described. The control rod is positioned by a coupled piston cylinder releasably coupled to a power drive means and the pressurized coolant is directed against the lower side of the piston. The coolant pressure is offset by a higher fiuid pressure applied to the upper surface of the piston and means are provided for releasing the higher pressure on the upper side of the piston so that the pressure of the coolant drives the piston upwardly, forcing the coupled control rod into the ncutron field of the reactor. (AEC)

Assessment of 25 kW free-piston Stirling technology alternatives for solar applications

NASA Technical Reports Server (NTRS)

Erbeznik, Raymond M.; White, Maurice A.; Penswick, L. B.; Neely, Ronald E.; Ritter, Darren C.; Wallace, David A.

1992-01-01

The final design, construction, and testing of a 25-kW free-piston advanced Stirling conversion system (ASCS) are examined. The final design of the free-piston hydraulic ASCS consists of five subsystems: heat transport subsystem (solar receiver and pool boiler), free-piston hydraulic Stirling engine, hydraulic subsystem, cooling subsystem, and electrical and control subsystem. Advantages and disadvantages are identified for each technology alternative. Technology alternatives considered are gas bearings vs flexure bearings, stationary magnet linear alternator vs moving magnetic linear alternator, and seven different control options. Component designs are generated using available in-house procedures to meet the requirements of the free-piston Stirling convertor configurations.

Electrorefiner

DOEpatents

Miller, W.E.; Tomczuk, Z.

1995-08-22

An apparatus is disclosed capable of functioning as a solid cathode and for removing crystalline structure from the upper surface of a liquid cathode, includes a metallic support vertically disposed with respect to an electrically insulating container capable of holding a liquid metal cathode. A piston of electrically insulating material mounted on the drive tube, surrounding the current lead, for vertical and rotational movement with respect thereto including a downwardly extending collar portion surrounding the metallic current lead. At least one portion of the piston remote from the metallic current lead being removed. Mechanism for lowering the piston to the surface of the liquid cathode and raising the piston from the surface along with mechanism for rotating the piston around its longitudinal axis. 5 figs.

Electrorefiner

DOEpatents

Miller, William E.; Tomczuk, Zygmunt

1995-01-01

An apparatus capable of functioning as a solid cathode and for removing crystalline structure from the upper surface of a liquid cathode, includes a metallic support vertically disposed with respect to an electrically insulating container capable of holding a liquid metal cathode. A piston of electrically insulating material mounted on the drive tube, surrounding the current lead, for vertical and rotational movement with respect thereto including a downwardly extending collar portion surrounding the metallic current lead. At least one portion of the piston remote from the metallic current lead being removed. Mechanism for lowering the piston to the surface of the liquid cathode and raising the piston from the surface along with mechanism for rotating the piston around its longitudinal axis.

One-Dimensional Shock Wave Formation by an Accelerating Piston. Ph.D. Thesis - Ohio State Univ.

NASA Technical Reports Server (NTRS)

Mann, M. J.

1970-01-01

The formation of a shock wave by a solid accelerating piston was studied. A theoretical solution using the method of characteristics for a perfect gas showed that a complex wave system exists, and that the compressed gas can have large gradients in temperature, density and entropy. Experiments were performed with a piston tube where piston speed, shock speed and pressure were measured. The comparison of theory and experiment was good.

In-cylinder flows of a motored four-stroke engine with flat-crown and slightly concave-crown pistons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, R.F.; Yang, H.S.; Yeh, C.-N.

2008-04-15

The temporal and spatial evolution processes of the in-cylinder flow structures and turbulence intensities in the symmetry and offset planes of a motored four-valve, four-stroke engine during the intake and compression strokes are diagnosed by using a particle image velocimeter. Two pistons of different crown shapes (flat-crown and slightly concave-crown pistons) are studied. The inception, establishment, and evolution of the tumbling vortical flow structures during the intake and compression strokes are clearly depicted. Quantitative strengths of the rotating vortical flow motions are presented by a dimensionless parameter, the tumble ratio, which can represent the mean angular velocity of the vorticesmore » in the target plane. The turbulence intensity of the in-cylinder flow is also calculated by using the measured time-varying velocity data. The results show that the flat-crown piston induces higher bulk-averaged tumble ratio and turbulence intensity than the slightly concave-crown piston does because the tumble ratio and turbulence generated by the flat-crown piston in the offset planes during the compression stroke are particularly large. The engine with the flat-crown piston also presents larger torque and power outputs and lower hydrocarbon emission than that with the slightly concave-crown piston. This might be caused by the enhanced combustion in the engine cylinder due to the stronger tumble ratio and turbulence intensity. (author)« less

Hazard analysis on the Mid-Atlantic Continental Slope, DCS lease sale 59 Area

USGS Publications Warehouse

Cardinell, Alex P.; Keer, Frederick R.

1982-01-01

A multi-parameter high-resolution seismic survey covering 253 offshore lease blocks was undertaken for analysis of critical structural and depositional features and a suite of piston cores was examined for geotechnical properties on the Mid-Atlantic continental slope in the OCS Lease Sale 59 area. The analysis of this data revealed complex interrelationships between a number of buried structural and depositional features indicating the existence of a variety of slope environments in the proposed lease sale area. The relationship these depositional features have to fault scarps and other topographic irregularities is critical to hazards assessment in this area. Southwest of the Hudson Canyon area, a major slump complex was partially delineated and numerous drape structures, which in some cases appear to have developed into contemporaneous down-to-the-basin faults, are associated with topographic irregularities. Southwest of the Baltimore Canyon area, slumps may be a result of the formation of mud diapers. These diapers? are the first reported in the Mid-Atlantic continental slope. Piston cores were collected at selected locations to provide information on geotechnical strength parameters of slumps, slides, and undisturbed sediments. These data indicate that localized areas of under consolidated sediments are found on valley walls and ridges of the upper slope. These zones may represent discrete areas where either mass movement has occurred or the potential for mass movement may exist. Many of the mass-movement features identified in the OCS Lease Sale 59 area may be Pleistocene in age and are related to' conditions prevailing during low sea stands. Since these conditions are presently absent, the potential for sediment mass movement does not appear to present a major problem to oil and gas operations within the proposed OCS Lease Sale 59 area.

Anthropogenic climate change has driven Lake Superior productivity beyond the range of Holocene variability

NASA Astrophysics Data System (ADS)

OBeirne, M. D.; Werne, J. P.; Hecky, R. E.; Johnson, T. C.; Katsev, S.; Reavie, E. D.

2013-12-01

Recent studies have noted that changes in Lake Superior's physical, chemical and biological processes are apparent - including a warming of the surface waters at a rate twice as great as the surrounding airshed in the last 20 years. These changes are often difficult to perceive as cause for concern when not placed within a historical context. In this study, bulk C and N abundance and stable isotope composition was determined on sediments from three piston and corresponding gravity cores, representing a record of lake-wide paleoproductivity trends spanning the Holocene. These data are compared with the same measurements on eight multi-cores sampled at high resolution spanning the past ~200 years, which allows for the historical comparison with recent (1800 A.D. to present) productivity trends. Throughout the Holocene, Lake Superior experienced a slow, steady increase in productivity consistent with conventional lake ontogeny. During the last 200 years, however, the Lake Superior basin has undergone biogeochemical changes that are unique in the context of the Holocene. Lake-wide sedimentary bulk organic carbon data indicate increasing primary production between 1900 and present, as indicated by a ~2‰ increase in δ13Corg. In contrast,δ15Norg values, which increased throughout the Holocene, become progressively 15N-depleted after 1900, likely due to atmospheric deposition of NOx from fossil fuel combustion. The most recent increases in primary productivity are likely a response to increasing water temperatures, leading to longer ice-free periods as previously documented in Lake Superior.

Influence of Volume Deformation Rate on the Intensity of Oil-Bearing Crop Pressing-out in Relation to Rape Extrudate

NASA Astrophysics Data System (ADS)

Slavnov, E. V.; Petrov, I. A.

2015-07-01

The influence of the volume deformation rate on the intensity of piston pressing-out of oil has been investigated. The results of pressing by a piston moving with different speeds are presented. Mathematical simulation is carried out for the stage of pressing-out after the termination of sample loading, when oil release occurs due to the accumulated deformations of the skeleton. It has been assumed that in mechanical pressing there remains the least residual content of oil. A dimensionless complex representing the ratio of the characteristic times of loading to the material response (the process of pressing) has been obtained. The dependence of the rate of oil pressing-out at the stage of pressure relaxation on the dimensionless complex has been determined.

Electromagnetic liquid pistons for capillarity-based pumping.

PubMed

Malouin, Bernard A; Vogel, Michael J; Olles, Joseph D; Cheng, Lili; Hirsa, Amir H

2011-02-07

The small scales associated with lab-on-a-chip technologies lend themselves well to capillarity-dominated phenomena. We demonstrate a new capillarity-dominated system where two adjoining ferrofluid droplets can behave as an electronically-controlled oscillator or switch by an appropriate balance of magnetic, capillary, and inertial forces. Their oscillatory motion can be exploited to displace a surrounding liquid (akin to an axial piston pump), forming electromagnetic "liquid pistons." Such ferrofluid pistons can pump a precise volume of liquid via finely tunable amplitudes (cf. pump stroke) or resonant frequencies (cf. pump speed) with no solid moving parts for long-term operation without wear in a small device. Furthermore, the rapid propagation of electromagnetic fields and the favorable scaling of capillary forces with size permit micron sized devices with very fast operating speeds (∼kHz). The pumping dynamics and performance of these liquid pistons is explored, with experimental measurements showing good agreement with a spherical cap model. While these liquid pistons may find numerous applications in micro- and mesoscale fluidic devices (e.g., remotely activated drug delivery), here we demonstrate the use of these liquid pistons in capillarity-dominated systems for chip-level, fast-acting adaptive liquid lenses with nearly perfect spherical interfaces.

Fuel savings with conventional hot water space heating systems by incorporating a natural gas powered heat pump. Preliminary project: Development of heat pump technology

NASA Astrophysics Data System (ADS)

Vanheyden, L.; Evertz, E.

1980-12-01

Compression type air/water heat pumps were developed for domestic heating systems rated at 20 to 150 kW. The heat pump is driven either by a reciprocating piston or rotary piston engine modified to operate on natural gas. Particular features of natural gas engines as prime movers, such as waste heat recovery and variable speed, are stressed. Two systems suitable for heat pump operation were selected from among five different mass produced car engines and were modified to incorporate reciprocating piston compressor pairs. The refrigerants used are R 12 and R 22. Test rig data transferred to field conditions show that the fuel consumption of conventional boilers can be reduced by 50% and more by the installation of engine driven heat pumps. Pilot heat pumps based on a 1,600 cc reciprocating piston engine were built for heating four two-family houses. Pilot pump operation confirms test rig findings. The service life of rotary piston and reciprocating piston engines was investigated. The tests reveal characteristic curves for reciprocating piston engines and include exhaust composition measurements.

Method of Fabricating Chopped-Fiber Composite Piston

NASA Technical Reports Server (NTRS)

Rivers, H. Kevin (Inventor); Ransone, Philip O. (Inventor); Northam, G. Burton (Inventor)

1999-01-01

A three-dimensional piston molding is fabricated from a mixture of chopped, carbon tow filaments of variable length, which are prepregged with carbonaceous organic resins and/or pitches and molded by conventional molding processes into a near net shape, to form a carbon-fiber reinforced organic-matrix composite part. Continuous reinforcement in the form of carbon-carbon composite tapes or pieces of fabric can be also laid in the mold before or during the charging of the mold with the chopped-fiber mixture, to enhance the strength in the crown and wrist-pin areas. The molded chopped-fiber reinforced organic-matrix composite parts are then pyrolized in an inert atmosphere, to convert the organic matrix materials to carbon. These pyrolized parts are then densified by reimpregnation with resins or pitches, which are subsequently carbonized. Densification is also accomplished by direct infiltration with carbon by vapor deposition processes. Once the desired density has been achieved, the piston molds are machined to final piston dimensions, and piston ring grooves are added. To prevent oxidation and/or to seal the piston surface or near surface, the chopped-fiber piston is coated with ceramic and/or metallic sealants: and/or coated with a catalyst.

The research on flow pulsation characteristics of axial piston pump

NASA Astrophysics Data System (ADS)

Wang, Bingchao; Wang, Yulin

2017-01-01

The flow pulsation is an important factor influencing the axial piston pump performance. In this paper we implement modeling and simulation of the axial piston pump with AMESim software to explore the flow pulsation characteristics under various factors . Theory analysis shows the loading pressure, angular speed, piston numbers and the accumulator impose evident influence on the flow pulsation characteristics. This simulation and analysis can be used for reducing the flow pulsation rate via properly setting the related factors.

Active Exhaust Silencing Systen For the Management of Auxillary Power Unit Sound Signatures

DTIC Science & Technology

2014-08-01

conceptual mass-less pistons are introduced into the system before and after the injection site, such that they will move exactly with the plane wave...Unit Sound Signatures, Helminen, et al. Page 2 of 7 either the primary source or the injected source. It is assumed that the pistons are ‘close...source, it causes both pistons to move identically. The pressures induced by the flow on the pistons do not affect the flow generated by the

TMA Chemical Release Payloads for Stratospheric Wind Measurements Auroral E Program and Related Programs

DTIC Science & Technology

1982-03-15

this work was to provide a piston tank filled with trimethyl aluminum for release as a trail in the upper atmosphere. This payload was launched from the...trail payloads. II. PAYLOAD DESCRIPTION The payload consists of a programmer section with plumbing and a piston tank section. The outer shell of the...payload is the wall of the piston tank . The liquid side of the piston tank is filled with 20 pounds of tri- methyl- aluminum (TMA). After filling the

An investigation of the fluid-structure interaction of piston/cylinder interface

NASA Astrophysics Data System (ADS)

Pelosi, Matteo

The piston/cylinder lubricating interface represents one of the most critical design elements of axial piston machines. Being a pure hydrodynamic bearing, the piston/cylinder interface fulfills simultaneously a bearing and sealing function under oscillating load conditions. Operating in an elastohydrodynamic lubrication regime, it also represents one of the main sources of power loss due to viscous friction and leakage flow. An accurate prediction of the time changing tribological interface characteristics in terms of fluid film thickness, dynamic pressure field, load carrying ability and energy dissipation is necessary to create more efficient interface designs. The aim of this work is to deepen the understanding of the main physical phenomena defining the piston/cylinder fluid film and to discover the impact of surface elastic deformations and heat transfer on the interface behavior. For this purpose, a unique fully coupled multi-body dynamics model has been developed to capture the complex fluid-structure interaction phenomena affecting the non-isothermal fluid film conditions. The model considers the squeeze film effect due to the piston micro-motion and the change in fluid film thickness due to the solid boundaries elastic deformations caused by the fluid film pressure and by the thermal strain. The model has been verified comparing the numerical results with measurements taken on special designed test pumps. The fluid film calculated dynamic pressure and temperature fields have been compared. Further validation has been accomplished comparing piston/cylinder axial viscous friction forces with measured data. The model has been used to study the piston/cylinder interface behavior of an existing axial piston unit operating at high load conditions. Numerical results are presented in this thesis.

Fluid powered linear piston motor with harmonic coupling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raymond, David W.

2016-09-20

A motor is disclosed that includes a module assembly including a piston that is axially cycled. The piston axial motion is coupled to torque couplers that convert the axial motion into rotary motion. The torque couplers are coupled to a rotor to rotate the rotor.

Overview of free-piston Stirling technology at the NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1985-01-01

An overview of the National Aeronautics and Space Administration (NASA) Lewis Research Center (Lewis) free-piston Stirling engine activities is presented. These activities include: (1) a generic free-piston Stirling technology project being conducted to develop technologies synergistic to both space power and terrestrial heat pump applications in a cooperative, cost-shared effort with the Department of Energy (DOE/Oak Ridge National Laboratory (ONRL)), and (2) a free-piston Stirling space-power technology demonstration project as part of the SP-100 program being conducted in support of the Department of Defense (DOD), DOE, and NASA/Lewis. The generic technology effort includes extensive parametric testing of a 1 kw free-piston Stirling engine (RE-1000), development and validation of a free-piston Stirling performance computer code, and fabrication and initial testing of an hydraulic output modification for the RE-1000 engine. The space power technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including early test results.

Magnetic bearings for free-piston Stirling engines

NASA Technical Reports Server (NTRS)

Curwen, P. W.; Flemig, D. P.; Rao, D. K.; Wilson, D. S.

1992-01-01

The feasibility and efficiency of applying magnetic bearings to free-piston Stirling-cycle power conversion machinery currently being developed for long-term space missions are assessed. The study was performed for a 50-kWe Reference Stirling Space Power Converter (RSSPC) which currently uses hydrostatic gas bearings to support the reciprocating displacer and power piston assemblies. Active magnetic bearings of the attractive electromagnetic type are feasible for the RSSPC power piston. Magnetic support of the displacer assembly would require unacceptable changes to the design of the current RSSPC. However, magnetic suspension of both displacer and power piston is feasible for a relative-displacer version of the RSSPC. Magnetic suspension of the RSSPC power piston can potentially increase overall efficiency by 0.5 to 1 percent (0.1 to 0.3 efficieny points). Magnetic bearings will also overcome several operational concerns associated with hydrostatic gas bearing systems. These advantages, however, are accompanied by a 5 percent increase in specific mass of the RSSPC.

Free-piston reciprocating cryogenic expander utilizing phase controller

NASA Astrophysics Data System (ADS)

Cha, Jeongmin; Park, Jiho; Kim, Kyungjoong; Jeong, Sangkwon

2017-02-01

In a free-piston expander which eliminates mechanical linkages, a prescribed behaviour of the free-piston movement is the key to an expander performance. In this paper, we have proposed an idea of reducing complexity of the free-piston expander. It is to replace both multiple solenoid valves and reservoirs that are indispensable in a previous machine with a combination of a single orifice-reservoir assembly. It functions as a phase controller like that of a pulse tube refrigerator so that it generates time-delay of pressure variation between the warm-end and the reservoir resulting in the intended expansion of the cold-end volume down to the pre-set reservoir pressure. The modeling of this unique free-piston reciprocating expander utilizing phase controller is developed to understand and predict the performance of the new-type expander. Additionally, the operating parameters are analysed at the specified conditions to enable one to develop a more efficient free-piston type cryogenic expander.

Simulation of interior ballistics flows in a shock tube

NASA Astrophysics Data System (ADS)

Seiler, F.

1983-07-01

The flow in front of and behind a projectile was investigated in a interior ballistics shock tube simulator. Flow patterns and heat flow were examined for flows with and without gas leakage. The boundary layers behind the piston can clearly be shown by differential interferograms. The dependence of the heat flow into the measuring tube wall on the base form is smaller than the signal perturbations. Flow patterns show no appreciable effect of gas leakage on the flow behind the piston; strong flow effects arise in front of the piston. The same effects are shown by heat flow measurements. In case of gas leakage heat flows into the tube wall before the piston reaches the wall. In the slit between piston and wall a maximum heat flow is found. High temperature gradients, due to the fact that hot gases come closer to the tube wall than in the boundary layer flow behind the piston, lead to high thermal loading of the wall materials which can cause cracks.

Magnetic bearings for free-piston Stirling engines

NASA Technical Reports Server (NTRS)

Curwen, P. W.; Fleming, D. P.; Rao, D. K.; Wilson, D. S.

1992-01-01

The feasibility and efficacy of applying magnetic bearings to free-piston Stirling-cycle power conversion machinery currently being developed for long-term space missions are assessed. The study was performed for a 50-kWe Reference Stirling Space Power Converter (RSSPC) which currently uses hydrostatic gas bearings to support the reciprocating displacer and power piston assemblies. Active magnetic bearings of the attractive electromagnetic type are feasible for the RSSPC power piston. Magnetic support of the displacer assembly would require unacceptable changes to the design of the current RSSPC. However, magnetic suspension of both displacer and power piston is feasible for a relative-displacer version of the RSSPC. Magnetic suspension of the RSSPC power piston can potentially increase overall efficiency by 0.5 to 1 percent (0.1 to 0.3 efficiency points). Magnetic bearings will also overcome several operational concerns associated with hydrostatic gas bearing systems. These advantages, however, are accompanied by a 5 percent increase in specific mass of the RSSPC.

Valving for controlling a fluid-driven reciprocating apparatus

DOEpatents

Whitehead, John C.

1995-01-01

A pair of control valve assemblies for alternately actuating a pair of fluid-driven free-piston devices by using fluid pressure communication therebetween. Each control valve assembly is switched by a pressure signal depending on the state of its counterpart's piston. The communication logic is arranged to provide overlap of the forward strokes of the pistons, so that at least one of the pair will always be pressurized. Thus, uninterrupted pumping of liquid is made possible from a pair of free-piston pumps. In addition, the speed and frequency of piston stroking is entirely dependent on the mechanical power load applied. In the case of a pair of pumps, this enables liquid delivery at a substantially constant pressure over the full range of flow rates, from zero to maximum flow. Each of the valve assemblies uses an intake-exhaust valve and a signal valve with the signal valve of one pump being connected to be pressure responsive to the piston of the opposite cylinder or pump.

Valving for controlling a fluid-driven reciprocating apparatus

DOEpatents

Whitehead, J.C.

1995-06-27

A pair of control valve assemblies is described for alternately actuating a pair of fluid-driven free-piston devices by using fluid pressure communication therebetween. Each control valve assembly is switched by a pressure signal depending on the state of its counterpart`s piston. The communication logic is arranged to provide overlap of the forward strokes of the pistons, so that at least one of the pair will always be pressurized. Thus, uninterrupted pumping of liquid is made possible from a pair of free-piston pumps. In addition, the speed and frequency of piston stroking is entirely dependent on the mechanical power load applied. In the case of a pair of pumps, this enables liquid delivery at a substantially constant pressure over the full range of flow rates, from zero to maximum flow. Each of the valve assemblies uses an intake-exhaust valve and a signal valve with the signal valve of one pump being connected to be pressure responsive to the piston of the opposite cylinder or pump. 15 figs.

Fluid-driven reciprocating apparatus and valving for controlling same

DOEpatents

Whitehead, John C.; Toews, Hans G.

1993-01-01

A control valve assembly for alternately actuating a pair of fluid-driven free-piston devices by using fluid pressure communication therebetween. Each control valve is switched by a pressure signal depending on the state of its counterpart's piston. The communication logic is arranged to provide overlap of the forward strokes of the pistons, so that at least one of the pair will always be pressurized. Thus, uninterrupted pumping of liquid is made possible from a pair of free-piston pumps. In addition, the speed and frequency of piston stroking is entirely dependent on the mechanical power load applied. In the case of a pair of pumps, this enables liquid delivery at a substantially constant pressure over the full range of flow rates, from zero to maximum flow. One embodiment of the invention utilized two pairs of fluid-driven free-piston devices whereby a bipropellant liquid propulsion system may be operated, so as to provide continuous flow of both fuel and oxidizer liquids when used in rocket applications, for example.

Overview of NASA Lewis Research Center free-piston Stirling engine activities

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1984-01-01

A generic free-piston Stirling technology project is being conducted to develop technologies generic to both space power and terrestrial heat pump applications in a cooperative, cost-shared effort. The generic technology effort includes extensive parametric testing of a 1 kW free-piston Stirling engine (RE-1000), development of a free-piston Stirling performance computer code, design and fabrication under contract of a hydraulic output modification for RE-1000 engine tests, and a 1000-hour endurance test, under contract, of a 3 kWe free-piston Stirling/alternator engine. A newly initiated space power technology feasibility demonstration effort addresses the capability of scaling a free-piston Stirling/alternator system to about 25 kWe; developing thermodynamic cycle efficiency or equal to 70 percent of Carnot at temperature ratios in the order of 1.5 to 2.0; achieving a power conversion unit specific weight of 6 kg/kWe; operating with noncontacting gas bearings; and dynamically balancing the system. Planned engine and component design and test efforts are described.

Late Holocene sea ice conditions in Herald Canyon, Chukchi Sea

NASA Astrophysics Data System (ADS)

Pearce, C.; O'Regan, M.; Rattray, J. E.; Hutchinson, D. K.; Cronin, T. M.; Gemery, L.; Barrientos, N.; Coxall, H.; Smittenberg, R.; Semiletov, I. P.; Jakobsson, M.

2017-12-01

Sea ice in the Arctic Ocean has been in steady decline in recent decades and, based on satellite data, the retreat is most pronounced in the Chukchi and Beaufort seas. Historical observations suggest that the recent changes were unprecedented during the last 150 years, but for a longer time perspective, we rely on the geological record. For this study, we analyzed sediment samples from two piston cores from Herald Canyon in the Chukchi Sea, collected during the 2014 SWERUS-C3 Arctic Ocean Expedition. The Herald Canyon is a local depression across the Chukchi Shelf, and acts as one of the main pathways for Pacific Water to the Arctic Ocean after entering through the narrow and shallow Bering Strait. The study site lies at the modern-day seasonal sea ice minimum edge, and is thus an ideal location for the reconstruction of past sea ice variability. Both sediment cores contain late Holocene deposits characterized by high sediment accumulation rates (100-300 cm/kyr). Core 2-PC1 from the shallow canyon flank (57 m water depth) is 8 meter long and extends back to 4200 cal yrs BP, while the upper 3 meters of Core 4-PC1 from the central canyon (120 mwd) cover the last 3000 years. The chronologies of the cores are based on radiocarbon dates and the 3.6 ka Aniakchak CFE II tephra, which is used as an absolute age marker to calculate the marine radiocarbon reservoir age. Analysis of biomarkers for sea ice and surface water productivity indicate stable sea ice conditions throughout the entire late Holocene, ending with an abrupt increase of phytoplankton sterols in the very top of both sediment sequences. The shift is accompanied by a sudden increase in coarse sediments (> 125 µm) and a minor change in δ13Corg. We interpret this transition in the top sediments as a community turnover in primary producers from sea ice to open water biota. Most importantly, our results indicate that the ongoing rapid ice retreat in the Chukchi Sea of recent decades was unprecedented during the last 4000 years.

Transient Characteristics of Free Piston Vuilleurnier Cycle Heat Pumps

NASA Astrophysics Data System (ADS)

Matsue, Junji; Fujimoto, Norioki; Shirai, Hiroyuki

A dynamic analysis of a free piston Vuilleumier cycle heat pump was performed using a time-stepping integration method to investigate transient characteristics under power controlling. The nonlinear relationship between displacement and force for pistons was taken into account for the motion of reciprocating components. The force for pistons is mainly caused by the pressure change of working gas varying with piston displacements; moreover nonlinear viscous dissipative force due to the oscillating flow of working gas in heat exchangers and discontinuous damping force caused by solid friction at piston seals and rod seals are included. The displacements of pistons and pressure changes in the Vuilleumier cycle heat pump were integrated by an ideal isothermal thermodynamic relationship. It was assumed that the flow friction was proportional to the kinematic pressure of working gas, and that the solid friction at the seals was due to the functions of the working gas pressure and the tension of seal springs. In order to investigate the transient characteristics of a proposed free piston Vuilleumier cycle heat pump machine when hot-side working gas temperatures and alternate force were changed, some calculations were performed and discussed. These calculation results make clear transient characteristics at starting and power controlling. It was further found that only a small amount of starter power is required in particular conditions. During controlling, the machine becomes unstable when there is ar elatively large reduction in cooling or heating power. Therefore, an auxiliary device is additionally needed to obtain stable operation, such as al inear motor.

CFD analysis of linear compressors considering load conditions

NASA Astrophysics Data System (ADS)

Bae, Sanghyun; Oh, Wonsik

2017-08-01

This paper is a study on computational fluid dynamics (CFD) analysis of linear compressor considering load conditions. In the conventional CFD analysis of the linear compressor, the load condition was not considered in the behaviour of the piston. In some papers, behaviour of piston is assumed as sinusoidal motion provided by user defined function (UDF). In the reciprocating type compressor, the stroke of the piston is restrained by the rod, while the stroke of the linear compressor is not restrained, and the stroke changes depending on the load condition. The greater the pressure difference between the discharge refrigerant and the suction refrigerant, the more the centre point of the stroke is pushed backward. And the behaviour of the piston is not a complete sine wave. For this reason, when the load condition changes in the CFD analysis of the linear compressor, it may happen that the ANSYS code is changed or unfortunately the modelling is changed. In addition, a separate analysis or calculation is required to find a stroke that meets the load condition, which may contain errors. In this study, the coupled mechanical equations and electrical equations are solved using the UDF, and the behaviour of the piston is solved considering the pressure difference across the piston. Using the above method, the stroke of the piston with respect to the motor specification of the analytical model can be calculated according to the input voltage, and the piston behaviour can be realized considering the thrust amount due to the pressure difference.

Mathematical Modelling of Liner Piston Maintenance Activity using Field Data to Minimize Overhauling Time and Human Energy Consumption

NASA Astrophysics Data System (ADS)

Belkhode, Pramod Namdeorao

2017-06-01

Field data based model is proposed to reduce the overhauling time and human energy consumed in liner piston maintenance activity so as to increase the productivity of liner piston maintenance activity. The independent variables affecting the phenomenon such as anthropometric parameters of workers (Eastman Kodak Co. Ltd in Section VIA Appendix-A: Anthropometric Data. Ergonomic Design for People at Work, Van Nostrans Reinhold, New York, 1), workers parameters, specification of liner piston data, specification of tools used in liner piston maintenance activity, specification of solvents, axial clearance of big end bearing and bolt elongation, workstation data (Eastman Kodak Co. Ltd in Work Place Ergonomic Design for People at Work, Van Nostrans Reinhold, New York, 2) and extraneous variables, namely, temperature, humidity at workplace, illumination at workplace and noise at workplace (Eastman Kodak Co. Ltd in Chapter V Environment Ergonomic Design for People at Work, Van Nostrans Reinhold, New York, 3) are taken into account. The model is formulated for dependent variables of liner piston maintenance activity to minimize the overhauling time and human energy consumption so as to improve the productivity of liner piston maintenance activity. The developed model can predict the performance of liner piston maintenance activity which involves man and machine system (Schenck in Theories of Engineering Experimentation, Mc-Graw Hill, New York 4). The model is then optimized by optimization technique and the sensitivity analysis of the model has also been estimated.

Glacial magnetite dissolution in abyssal NW Pacific sediments - evidence for carbon trapping?

NASA Astrophysics Data System (ADS)

Korff, Lucia; von Dobeneck, Tilo; Frederichs, Thomas; Kasten, Sabine; Kuhn, Gerhard; Gersonde, Rainer; Diekmann, Bernhard

2016-04-01

The abyssal North Pacific Ocean's large volume, depth, and terminal position on the deep oceanic conveyor make it a candidate site for deep carbon trapping as postulated by climate theory to explain the massive glacial drawdown of atmospheric CO2. As the major basins of the North Pacific have depths of 5500-6500m, far below the modern and glacial Calcite Compensation Depths (CCD), these abyssal sediments are carbonate-free and therefore not suitable for carbonate-based paleoceanographic proxy reconstructions. Instead, paleo-, rock and environmental magnetic methods are generally well applicable to hololytic abyssal muds and clays. In 2009, the international paleoceanographic research cruise SO 202 INOPEX ('Innovative North Pacific Experiment') of the German RV SONNE collected two ocean-spanning EW sediment core transects of the North Pacific and Bering Sea recovering a total of 50 piston and gravity cores from 45 sites. Out of seven here considered abyssal Northwest Pacific piston cores collected at water depths of 5100 to 5700m with mostly coherent shipboard susceptibility logs, the 20.23m long SO202-39-3, retrieved from 5102 m water depth east of northern Shatsky Rise (38°00.70'N, 164°26.78'E), was rated as the stratigraphically most promising record of the entire core transect and selected for detailed paleo- and environmental magnetic, geochemical and sedimentological investigations. This core was dated by correlating its RPI and Ba/Ti records to well-dated reference records and obviously provides a continuous sequence of the past 940 kyrs. The most striking orck magnetic features are coherent magnetite-depleted zones corresponding to glacial periods. In the interglacial sections, detrital, volcanic and even submicron bacterial magnetite fractions are excellently preserved. These alternating magnetite preservation states seem to reflect dramatic oxygenation changes in the deep North Pacific Ocean and hint at large-scale benthic glacial carbon trapping followed by subsequent interglacial carbon burn-down and CO2 release. Abyssal Northwest Pacific sediments may have served as glacial carbon reservoir in particular since the onset of systematic 100 kyr ice age cycles at the end of the Mid-Pleistocene transition (MPT). Stagnant glacial Antarctic Bottom Water, which expanded primarily into abyssal South Atlantic basins during the MPT interim phase, thereafter seemed to flow preferentially into the deeper and larger abyssal Indo-Pacific basins, where it may have enabled more efficient carbon-trapping. More intensive scavenging of the Northwest Pacific surface ocean by enhanced glacial Asian dust flux is suggested by parallel TOC and quartz contents, enhancing glacial carbon accumulation despite potentially lower export production. The magnetic records also identify numerous partly consistent tephra layers, which can be matched between most records of the core transect.

Piston Temperatures in an Air-Cooled Engine for Various Operating Conditions

NASA Technical Reports Server (NTRS)

Manganiello, Eugene J

1940-01-01

As part of a program for the study of piston cooling, this report presents the results of tests conducted on a single-cylinder, air-cooled, carburetor engine to determine the effect of engine operating conditions on the temperatures at five locations on the piston.

GOLD PRESSURE VESSEL SEAL

DOEpatents

Smith, A.E.

1963-11-26

An improved seal between the piston and die member of a piston-cylinder type pressure vessel is presented. A layer of gold, of sufficient thickness to provide an interference fit between the piston and die member, is plated on the contacting surface of at least one of the members. (AEC)

Spherical Joint Piston and Connecting Rod Developed

NASA Technical Reports Server (NTRS)

1996-01-01

Under an interagency agreement with the Department of Energy, the NASA Lewis Research Center manages a Heavy-Duty Diesel Engine Technology (HDET) research program. The overall program objectives are to reduce fuel consumption through increased engine efficiency, reduce engine exhaust emissions, and provide options for the use of alternative fuels. The program is administered with a balance of research contracts, university research grants, and focused in-house research. The Cummins Engine Company participates in the HDET program under a cost-sharing research contract. Cummins is researching and developing in-cylinder component technologies for heavy-duty diesel engines. An objective of the Cummins research is to develop technologies for a low-emissions, 55-percent thermal efficiency (LE-55) engine. The best current-production engines in this class achieve about 46-percent thermal efficiency. Federal emissions regulations are driving this technology. Regulations for heavy duty diesel engines were tightened in 1994, more demanding emissions regulations are scheduled for 1998, and another step is planned for 2002. The LE-55 engine emissions goal is set at half of the 1998 regulation level and is consistent with plans for 2002 emissions regulations. LE-55 engine design requirements to meet the efficiency target dictate a need to operate at higher peak cylinder pressures. A key technology being developed and evaluated under the Cummins Engine Company LE-55 engine concept is the spherical joint piston and connecting rod. Unlike conventional piston and connecting rod arrangements which are joined by a pin forming a hinged joint, the spherical joint piston and connecting rod use a ball-and-socket joint. The ball-and-socket arrangement enables the piston to have an axisymmetric design allowing rotation within the cylinder. The potential benefits of piston symmetry and rotation are reduced scuffing, improved piston ring sealing, improved lubrication, mechanical and thermal load symmetry, reduced bearing stresses, reduced running clearances, and reduced oil consumption. The spherical joint piston is a monolithic, squeeze-cast, fiber-reinforced aluminum piston. The connecting rod has a ball end that seats on a spherical saddle within the piston and is retained by a pair of aluminum bronze holder rings. The holder rings are secured by a threaded ring that mates with the piston. As part of the ongoing research and development activity, the Cummins Engine Company successfully completed a 100-hr test of the spherical joint piston and connecting rod at LE- 55 peak steady-state engine conditions. In addition, a 100-hr transient cycle test that varied engine conditions between LE-55 no-load and LE-55 full-load was successfully completed.

Measurements of erosion potential using Gust chamber in Yolo Bypass near Sacramento, California

USGS Publications Warehouse

Work, Paul A.; Schoellhamer, David H.

2018-04-27

This report describes work performed to quantify the erodibility of surface soils in the Yolo Bypass (Bypass) near Sacramento, California, for use in the California Department of Water Resources (DWR) Yolo Bypass D-MCM mercury model. The Bypass, when not serving as a floodway, is heavily utilized for agriculture. During flood events, surface water flows over the soil, resulting in the application of a shear stress to the soil. The shear stress is a function of flow speed and is often assumed to vary as the square of flow speed. Once the shear stress reaches a critical value, erosion commences, and the erosion rate typically increases with applied shear stress. The goal of the work described here was to quantify this process and how it varies throughout the major land uses found in the Yolo Bypass.Each of the major land uses found in the Bypass was targeted for sediment coring and two side-by-side cores, 10 centimeters in diameter, were extracted at each site for testing in a Gust erosion chamber. This device consists of a cylinder with a piston and cap installed to contain a sediment sample and overlying water. In most instances, coring was done with the cylinder, the piston and cap were installed, and testing commenced immediately. The cap at the top of the cylinder contains vanes to induce rotation of the flow and is driven by an electric motor, simulating the bed shear stress experienced by the soil in a flood event. Ambient water is introduced to the cylinder, passes through the device, and carries eroded sediment out of the chamber. The exiting water is tested for turbidity, and water samples obtained to relate turbidity to suspended sediment concentration are used to compute erosion rates for each of the applied shear stresses.The result for each sediment core is (1) definition of the critical shear stress required to initiate sediment erosion and (2) estimation of coefficients required to relate erosion rate to applied shear stress once this critical shear-stress threshold has been exceeded. These quantities were computed for each of the sites sampled. In total, 10 locations were sampled, representing 10 land uses ranging from wild and white rice fields to the flooded Liberty Island and the Toe Drain that receives runoff from much of the cultivated land (table 1).The Gust chamber test causes the erosion of a very small layer of sediment, typically less than a millimeter thick. The strength of the soil within this layer increases with depth, typically, and this soil strength versus depth is measured in the testing process.Results for each land use type tested are presented as the initial critical shear stress at which erosion began and the rate at which erosion increases as shear stress increases (table 2). Of the land use types sampled, irrigated pasture displayed the lowest critical shear stress, meaning that it required the smallest flow speed to initiate erosion. But in this case, the rate of increase of the subsequent erosion, given higher flow speeds, was small. The wild rice field samples exhibited a higher critical shear stress but also exhibited a much higher erosion rate once the critical shear stress was exceeded. The erosion rate for wild rice was about three times greater than that for white rice. Bear in mind that these results are based on only two cores tested per site, and variability between fields with the same crop could be significant. Approved digital data can be viewed and downloaded from ScienceBase, at https://doi.org/10.5066/F7BV7DQC. These results are being used to calculate erosion rates in the DWR Yolo Bypass D-MCM mercury model.The Toe Drain was very difficult to sample, owing to hard, consolidated sediments on the channel bed. On the first visit, two cores were obtained successfully, and testing revealed very different results. A second visit was made, but it was not possible to obtain cores suitable for testing with the coring equipment used. The available results suggest that Toe Drain soil is highly erodible (low critical shear stress and high erosion rate once initiated) despite being difficult to sample. As a collector of runoff, it also has the potential to accumulate soils eroded from adjacent areas, subsequent to storm events, as flows subside. This deposited material will typically be more erodible than the material that it lands on. The deposition and resuspension of material was not simulated in the testing described here because the applied shear stress increases monotonically during testing.The spatial distribution of mean grain size, loss on ignition, and percent fines of Yolo Bypass soils are also presented. Sediment sampling for this effort was performed by DWR; the U.S. Geological Survey (USGS) performed the sample analysis. These data should thus be considered provisional, but the remainder of the data presented here, and this report, have been through the formal U.S. Geological Survey review process.A separate effort has been made by others to develop numerical model results defining the spatially  varying, time-dependent hydrodynamics in the Yolo Bypass. These model results are being used to quantify shear stress on the soil surface, which together with the Gust chamber results shown here, are used for the DWR Yolo Bypass D-MCM mercury transport model to compute erosion rates for each time step.

20. ENGINE/PUMP HOUSE EXTENSION, PUMP NO. 4, HOUSING FOR ECCENTRICS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. ENGINE/PUMP HOUSE EXTENSION, PUMP NO. 4, HOUSING FOR ECCENTRICS THAT CONTROL THE STEAM FOR EAST PISTON LOCATED BELOW THE PISTON CRANKSHAFT HUB AND ABOVE THE THRUST BEARING; CONTROL RODS FOR PISTON NO. 3 LOCATED AT RIGHT. - Deer Island Pumping Station, Boston, Suffolk County, MA

Entropic Damping of the Motion of a Piston

ERIC Educational Resources Information Center

Mungan, Carl E.

2017-01-01

The concept of an "entropic force" can be introduced by considering a familiar setup, namely a horizontal cylinder enclosing an ideal monatomic gas by a piston of cross-sectional area "A" and mass "m" that can slide without friction. The surrounding atmospheric pressure P[subscript atm] keeps the piston from flying…

Loss terms in free-piston Stirling engine models

NASA Technical Reports Server (NTRS)

Gordon, Lloyd B.

1992-01-01

Various models for free piston Stirling engines are reviewed. Initial models were developed primarily for design purposes and to predict operating parameters, especially efficiency. More recently, however, such models have been used to predict engine stability. Free piston Stirling engines have no kinematic constraints and stability may not only be sensitive to the load, but also to various nonlinear loss and spring constraints. The present understanding is reviewed of various loss mechanisms for free piston Stirling engines and how they have been incorporated into engine models is discussed.

Magnetically Retained Relief Valve

NASA Technical Reports Server (NTRS)

Johnson, Wesley L. (Inventor); Cook, Charles R. (Inventor)

2017-01-01

A pressure relief valve includes a housing having a fluid inlet and at least one fluid outlet. A first structure mounted in the housing and fixed in relation thereto is in magnetic attraction with a second structure coupled to a piston disposed in a portion of the housing. The piston defines a chamber disposed adjacent to the fluid outlet(s) throughout the piston's stroke. The piston includes a sealing element providing a sealing force to prevent flow through the valve. The sealing force is independent of the magnetic attraction force between the first and second structures.

Pole pulling apparatus and method

DOEpatents

McIntire, Gary L.

1989-01-01

An apparatus for removal of embedded utility-type poles which removes the poles quickly and efficiently from their embedded position without damage to the pole or surrounding structures. The apparatus includes at least 2 piston/cylinder members equally spaced about the pole, and a head member affixed to the top of each piston. Elongation of the piston induces rotation of the head into the pole to increase the gripping action and reduce slippage. Repeated actuation and retraction of the piston and head member will "jack" the pole from its embedded position.

Geoacoustic models of Coastal Bottom Strata at Jeongdongjin in the Korean continental margin of the East Sea

NASA Astrophysics Data System (ADS)

Ryang, Woo Hun; Han, Jooyoung

2017-04-01

Geoacoustic models provide submarine environmental data to predict sound transmission through submarine bottom layers of sedimentary strata and acoustic basement. This study reconstructed four geoacoustic models for sediments of 50 m thick at the Jeongdongjin area in the western continental margin of the East Sea. Bottom models were based on about 1100 line-km data of the high-resolution air-gun seismic and subbottom profiles (SBP) with sediment cores. The 4 piston cores were analyzed for reconstruction of the bottom and geoacoustic models in the study area, together with 2 long cores in the adjacent area. P-wave speed in the core sediment was measured by the pulse transmission technique, and the resonance frequency of piezoelectric transducers was maintained at 1 MHz. Measurements of 42 P-wave speeds and 41 attenuations were fulfilled in three core sediments. For actual modeling, the P-wave speeds of the models were compensated to in situ depth below the sea floor using the Hamilton method. These geoacoustic models of coastal bottom strata will be used for geoacoustic and underwater acoustic experiments reflecting vertical and lateral variability of geoacoustic properties in the Jeongdongjin area of the East Sea. Keywords: geoacosutic model, bottom model, P-wave speed, Jeongdongjin, East Sea Acknowledgements: This research was supported by the research grants from the Agency of Defense Development (UD140003DD and UE140033DD).

High-Resolution Paleomagnetic Observations from Ocean Drilling: Insights from Coring Thick Sediment Drift Deposits

NASA Astrophysics Data System (ADS)

Acton, G. D.; Clement, B. M.; Lund, S. P.; Okada, M.; Williams, T.

2003-04-01

With the advent of the Hydraulic Piston Corer at the end of the Deep Sea Drilling Program and its enhanced successor, the Advanced Piston Corer (APC), developed by the Ocean Drilling Program (ODP), coring through thick (>100 m), rapidly deposited sequences of unconsolidated to partially consolidated sediments with near 100% recovery has become common place. Although much of the emphasis for site selection has been based on paleoceanographic objectives, the impact to the field of paleomagnetism has been dramatic, both in the instruments used to analyze the large quantity of core recovered and in the questions that can be answered concerning geomagnetic field behavior and paleoenvironmental conditions. The largest change has come in the construction of relative paleointensity records, which have provided previously unimagined details about how the geomagnetic field varies in strength during stable polarity intervals as well as during reversals and excursions. These records have allowed more realistic models of the geomagnetic field to be developed while also providing a new chronologic tool for high-resolution dating and global correlation of geomagnetic events. Studies of how the paleomagnetic direction varies through time have not advanced as rapidly and have instead mainly been focused on short time intervals across a few geomagnetic reversals. It should, however, be possible to construct and compare secular variation records with millennial or better resolution that span the past one million years from sites around the world as correlation and chronologies between sites improve. We will give an overview that focuses on secular variation records that are being constructed from sediment drifts drilled in the western North Atlantic during ODP Leg 172. Our results will be used to address questions concerning what percent of time the geomagnetic field is in a stable state versus transitional or excursional states, what the relationship is between directional variability and relative paleointensity, which secular variation features are global and which are local, what is the origin of local directional changes, and how climate and rock magnetic changes influence the paleomagnetic signal.

Audiological comparison between two different clips prostheses in stapes surgery.

PubMed

Potena, M; Portmann, D; Guindi, S

2015-01-01

To compare audiometric results and complications of stapes surgery with two different types of piston prosthesis, the Portmann Clip Piston (Medtronic) (PCP) and the Soft Clip Piston (Kurz) (SCP). Study conducted on 64 patients who underwent primary stapedotomy from 2008 to 2011. We matched for each case of stapedotomy with the PCP (Medtronic Xomed Inc. Portmann Clip Piston Stainless Steel/Fluoroplastic) a case with the SCP (Heinz Kurz GmbH Medizintechnik Soft Piston Clip Titanium). Each group consisted of 32 patients, and patients in both groups were matched with respect to gender, age, bilateral or unilateral otosclerosis, otological symptoms (tinnitus, vertigo or dizziness), family history, operated side and the Portmann grading for otosclerosis. The length of the prosthesis used was reported. Post-operative complications such as tinnitus, vertigo, hearing loss and altered taste were documented. Each patient was subjected to a preoperative and postoperative audiogram (follow-up at the second month after the surgery). We used the Student test for statistical analysis. Statistical significance was set at < 0.01. None of the patients experienced a post-operative hearing loss and none required a later revision surgery. No statistically significant difference was found between the two populations regarding demographic data (age, sex, side, bilaterality, family history, stage and lenght of piston) and hearing level (> 0.01) in the air, bone conduction and air-bone gap (ABG). Postoperative complications did not result to be significantly different between the two groups. Also, both groups showed a significant improvement (< 0.01) in the post-operative air, bone conduction and air-bone gap. There was no statistically significant difference (> 0.01) between the post-operative hearing results (bone conduction, air conduction, air-bone gap) using the two pistons. The mean ABG improvement was respectively 16.63 dB in the SCP group and 20.59 dB in the PCP group. The titanium Soft clip piston (SCP) is a good alternative to the Portmann clip piston (PCP). Nevertheless there are some differences in the surgical fixing of these two pistons in the correct position.

Shock induced crystallization of amorphous Nickel powders

NASA Astrophysics Data System (ADS)

Cherukara, Mathew; Strachan, Alejandro

2015-06-01

Recent experimental work has shown the efficacy of amorphous Ni/crystalline Al composites as energetic materials, with flame velocities twice that of a comparable crystalline Ni/crystalline Al system. Of further interest is the recrystallization mechanisms in the pure amorphous Ni powders, both thermally induced and mechanically induced. We present large-scale molecular dynamics simulations of shock-induced recrystallization in loosely packed amorphous Nickel powders. We study the time dependent nucleation and growth processes by holding the shocked samples at the induced pressures and temperatures for extended periods following the passage of the shock (up to 6 ns). We find that the nanostructure of the recrystallized Ni and time scales of recrystallization are dependent on the piston velocity. At low piston velocities, nucleation events are rare, leading to long incubation times and a relatively coarse nanostructure. At higher piston velocities, local variations in temperature due to jetting phenomena and void collapse, give rise to multiple nucleation events on time scales comparable to the passage of the shock wave, leading to the formation of a fine-grained nanostructure. Interestingly, we observe that the nucleation and growth process occurs in two steps, with the first nuclei crystallizing into the BCC structure, before evolving over time into the expected FCC structure. U.S. Defense Threat Reduction Agency, HDTRA1-10-1-0119 (Program Manager Suhithi Peiris).

Diamond-anvil high-pressure cell with improved X-ray collimation system

DOEpatents

Schiferl, David; Olinger, Barton W.; Livingston, Robert W.

1986-01-01

An adjustable X-ray collimation system for a diamond-anvil high-pressure cell of the type including a cooperable piston and cylinder and a pair of opposing diamonds located between the head of the piston and the head of the cylinder. The X-ray collimation system includes a tubular insert which contains an X-ray collimator. The insert is engageable in the bore of the piston. The collimator is mounted within the insert by means of an elastomeric O-ring at the end closest the opposed diamonds, and by means of a set of adjustable set screws at the opposite end. By adjustment of the set screws the collimator can be pivoted about the O-ring and brought into alignment with the opposed diamonds and the sample contained therein. In the preferred embodiment there is further provided a set of plugs which are insertable in the bore of the collimator. The plugs have bores of different diameters. By successively inserting plugs of progressively smaller bore diameters and adjusting the alignment of the collimator with each plug, the collimator can be quickly brought into accurate alignment with the diamonds. The collimation system allows alignment of the collimator either before or after the cell has been loaded and pressurized.

Diamond-anvil high-pressure cell with improved x-ray collimation system

DOEpatents

Schiferl, D.; Olinger, B.W.; Livingston, R.W.

1984-03-30

An adjustable x-ray collimation system for a diamond-anvil high-pressure cell of the type including a cooperable piston and cylinder and a pair of opposing diamonds located between the head of the piston and the head of the cylinder. The x-ray collimation system includes a tubular insert which contains an x-ray collimator. The insert is engageable in the bore of the piston. The collimator is mounted within the insert by means of an elastomeric o-ring at the end closest the opposed diamonds, and by means of a set of adjustable set screws at the opposite end. By adjustment of the set screws the collimator can be pivoted about the o-ring and brought into alignment with the opposed diamonds and the sample contained therein. In the preferred embodiment there is further provided a set of plugs which are insertable in the bore of the collimator. The plugs have bores of different diameters. By successively inserting plugs of progressively smaller bore diameters and adjusting the alignment of the collimator with each plug, the collimator can be quickly brought into accurate alignment with the diamonds. The collimation system allows alignment of the collimator either before or after the cell has been loaded and pressurized.

75 FR 12710 - Airworthiness Directives; Bombardier, Inc., Model DHC-8-400 Series Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-17

... for the main landing gear lock actuator assembly, retraction actuator assembly rod end and piston, and... for the main landing gear lock actuator assembly, retraction actuator assembly rod end and piston, and..., retraction actuator assembly rod end and piston, and the upper bearing in the main landing gear shock strut...

Stirling engine piston ring

DOEpatents

Howarth, Roy B.

1983-01-01

A piston ring design for a Stirling engine wherein the contact pressure between the piston and the cylinder is maintained at a uniform level, independent of engine conditions through a balancing of the pressure exerted upon the ring's surface and thereby allowing the contact pressure on the ring to be predetermined through the use of a preloaded expander ring.

Modeling of the 35-mm Rarefaction Wave Gun

DTIC Science & Technology

2006-05-01

16 Figure 9. Shot 2-6-2; light piston, early vent, high- pressure group : gauge P1 (line) and...2-6-3; light piston, early vent, low- pressure group : gauge P1 (line) and simulation (dot...18 Figure 11. Gun travel; light piston, early vent, high- pressure group : shot 2-6-1

Activating the nuclear piston mechanism of 3D migration in tumor cells

PubMed Central

2017-01-01

Primary human fibroblasts have the remarkable ability to use their nucleus like a piston, switching from low- to high-pressure protrusions in response to the surrounding three-dimensional (3D) matrix. Although migrating tumor cells can also change how they migrate in response to the 3D matrix, it is not clear if they can switch between high- and low-pressure protrusions like primary fibroblasts. We report that unlike primary fibroblasts, the nuclear piston is not active in fibrosarcoma cells. Protease inhibition rescued the nuclear piston mechanism in polarized HT1080 and SW684 cells and generated compartmentalized pressure. Achieving compartmentalized pressure required the nucleoskeleton–cytoskeleton linker protein nesprin 3, actomyosin contractility, and integrin-mediated adhesion, consistent with lobopodia-based fibroblast migration. In addition, this activation of the nuclear piston mechanism slowed the 3D movement of HT1080 cells. Together, these data indicate that inhibiting protease activity during polarized tumor cell 3D migration is sufficient to restore the nuclear piston migration mechanism with compartmentalized pressure characteristic of nonmalignant cells. PMID:27998990

Gas-Induced Rectified Motion of a Solid Object in a Liquid-Filled Housing during Vibration: Analysis and Experiments

NASA Astrophysics Data System (ADS)

Torczynski, J. R.; O'Hern, T. J.; Clausen, J. R.; Koehler, T. P.

2017-11-01

The motion of a solid object (a piston) that fits closely within a housing filled with viscous liquid is studied. If a small amount of gas is introduced and the system is subjected to axial vibration, then the piston exhibits rectified motion when the drag on the piston depends on its position within the housing. An idealized system, in which the piston is suspended freely between two springs and the gas is replaced with two compressible bellows, is analyzed theoretically and studied experimentally. For a given vibration amplitude or frequency, the piston either remains near its original position (``up'') or moves to a different position (``down''), where its spring suspension is compressed. Analytical and experimental regime maps of the amplitudes and frequencies at which the piston is up or down are in good agreement. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA0003525.

Aluminum Matrix Composite (AlSi7Mg2Sr0.03/SiCp) Pistons Obtained by Mechanical Mixing Method

PubMed Central

2017-01-01

Metal matrix composites are undoubtedly a group of advanced engineering materials. Compared to unreinforced matrix material, they are characterized by increased strength, greater stiffness, increased wear resistance, better mechanical properties and dimensional stability at elevated temperatures as well as lower density. Due to its very favorable tribological properties for many years research has been conducted on the application of MMC in friction node. The article presents important technological aspects related to the production and properties of composite pistons. Under industrial conditions, a composite suspension (AlSi7Mg2Sr0.03/SiCp 10 vol %) was prepared to allow casting of the semi-finished pistons series. Machining parameters of the working surfaces of the piston were selected on the basis of the turning test made on PCD, PCNM and uncoated carbide tools. The tribological properties of the composite pistons were determined on the basis of the pin-on-disc and the abrasion wear. The scuffing tests carried out under real operating conditions have confirmed the possibility of using composite pistons in air compressors. PMID:29283419

Clinical significance of stapedioplasty biomechanics: swimming, diving, flying after stapes surgery.

PubMed

Hüttenbrink, Karl-Bernd

2007-01-01

A piston prosthesis in stapedioplasty significantly modifies the function of the normal ossicular chain. Due to the fact that the ear works as a pressure receptor, a piston prosthesis will be displaced at ambient air pressure changes in a different way than the normal stapes. Our ear is constantly exposed to these pressure changes in daily live, for example during swallowing, with tubal opening, with wind gusts at the external ear, during flying, or diving. Temporal bone experiments showed that elevated static pressures, like in tympanometry, can displace a piston up to 0.5mm in the vestibule. These large movements, which are caused by the missing attachment of the piston to the annual ligament, may explain why a short piston can be lifted out of the footplate perforation (e.g. after sneezing) or a piston with excessive length might come into contact with the membranous labyrinth, causing vertigo with an inward movement. Flying or diving can be performed by the patients after stapedioplasty, provided that a test with tympanometry is tolerated without evoking vertigo.

ACCELERATION INTEGRATING MEANS

DOEpatents

Wilkes, D.F.

1961-08-29

An acceleration responsive device is described. A housing has at one end normally open electrical contacts and contains a piston system with a first part of non-magnetic material having metering orifices in the side walls for forming an air bearing between it and the walls of the housing; this first piston part is normally held against the other end of the housing from the noted contacts by a second piston or reset part. The reset part is of partly magnetic material, is separable from the flrst piston part, and is positioned within the housing intermediate the contacts and the first piston part. A magnet carried by the housing imposes a retaining force upon the reset part, along with a helical compression spring that is between the reset part and the end with the contacts. When a predetermined acceleration level is attained, the reset part overcomes the bias or retaining force provided by the magnet and the spring'' snaps'' into a depression in the housing adjacent the contacts. The first piston part is then free to move toward the contacts with its movement responsive tc acceleration forces and the metering orifices. (AEC)

A study on the development of engineering plastic piston used in the shock absorber

NASA Astrophysics Data System (ADS)

Kim, Young-Ho; Bae, Won-Byong; Lim, Dong-Ju; Suh, Yun-Soo

1998-08-01

A piston is an important component of the shock absorber which determines comfortable riding and handling. Conventional piston is made of metal powder that is pressed in a mold, and then sintered at high temperatures below the melting point before machining processes such as drilling, sizing and teflon banding. This study aims at cutting down cost and weight, and improving the process by replacing the traditional sintering process used for manufacturing the shock absorber with the injection molding process adopting engineering plastics as raw material. To analyze the injection molding process, we used the commercial program, MOLDFLOW, and obtained an optimal combination of the process parameters. In addition, by comparing the engineering plastic piston with the metal powder piston through the formability and the performance experiments, we confirmed the availability of this alternative process suggested.

Turbocharger with sliding piston, and having vanes and leakage dams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, Quentin; Alnega, Ahmed

2011-12-06

A turbocharger having a sliding piston for regulating exhaust gas flow into the turbine wheel includes a set of first vanes mounted on a fixed first wall of the turbine nozzle and projecting axially toward an opposite second wall of the nozzle, and/or a set of second vanes mounted on the end of the piston and projecting in an opposite axial direction toward the first wall of the nozzle. For the/each set of vanes, there are leakage dams formed on the wall that is adjacent the vane tips when the piston is closed. The leakage dams are closely adjacent themore » vane tips and discourage exhaust gas from leaking in a generally radial direction past the vane tips as the piston just begins to open from its fully closed position.« less

Slocum-TREC Thermal Glider

NASA Technical Reports Server (NTRS)

Huntsberger, Terry; Jones, Jack A.; Valdez, Thomas; Stirbl, Rob

2012-01-01

JPL is now teaming with Teledyne-Webb-Research to produce the first thermal glider that uses PCM for direct buoyancy control (not electronic pumps) and to produce all other required electricity. TWR has increased electrical production total efficiency from 0.45 to 0.61. JPL performed over 6000 cycles (2.4 years) of accelerated life testing of a piston accumulator. Design, fabrication, and testing will be performed in 2012, with deployment by Rutgers University in late 2012. The proposed goal of the ocean endurance tests was 3 months, but will be extended to at last 1 year. The piston accumulator was cycled over 6,000 times in a three-month period in order to simulate continuous glider life of about 2.4 years, The life test data suggests that we might accumulate roughly 0.5 cc of gas in the oil bladders for each cycle. PCM canisters will be fabricated with a compressed aluminum foam core, 7.5% foam selected (< 42 minutes to freeze anticipated) An Axi 5345/18 3-Phase AC alternator selected for power generation, 61% energy storage efficiency A 4-Cell A123 Energy Storage Systems battery selected for energy storage, buss voltage 14.4 to 12.5 V (13.2 V nominal) Glider deployment expected in late 2012

A high resolution pneumatic stepping actuator for harsh reactor environments

NASA Astrophysics Data System (ADS)

Tippetts, Thomas B.; Evans, Paul S.; Riffle, George K.

1993-01-01

A reactivity control actuator for a high-power density nuclear propulsion reactor must be installed in close proximity to the reactor core. The energy input from radiation to the actuator structure could exceed hundreds of W/cc unless low-cross section, low-absorptivity materials are chosen. Also, for post-test handling and subsequent storage, materials should not be used that are activated into long half-life isotopes. Pneumatic actuators can be constructed from various reactor-compatible materials, but conventional pneumatic piston actuators generally lack the stiffness required for high resolution reactivity control unless electrical position sensors and compensated electronic control systems are used. To overcome these limitations, a pneumatic actuator is under development that positions an output shaft in response to a series of pneumatic pulses, comprising a pneumatic analog of an electrical stepping motor. The pneumatic pulses are generated remotely, beyond the strong radiation environment, and transmitted to the actuator through tubing. The mechanically simple actuator uses a nutating gear harmonic drive to convert motion of small pistons directly to high-resolution angular motion of the output shaft. The digital nature of this actuator is suitable for various reactor control algorithms but is especially compatible with the three bean salad algorithm discussed by Ball et al. (1991).

The analysis and compensation of errors of precise simple harmonic motion control under high speed and large load conditions based on servo electric cylinder

NASA Astrophysics Data System (ADS)

Ma, Chen-xi; Ding, Guo-qing

2017-10-01

Simple harmonic waves and synthesized simple harmonic waves are widely used in the test of instruments. However, because of the errors caused by clearance of gear and time-delay error of FPGA, it is difficult to control servo electric cylinder in precise simple harmonic motion under high speed, high frequency and large load conditions. To solve the problem, a method of error compensation is proposed in this paper. In the method, a displacement sensor is fitted on the piston rod of the electric cylinder. By using the displacement sensor, the real-time displacement of the piston rod is obtained and fed back to the input of servo motor, then a closed loop control is realized. There is compensation of pulses in the next period of the synthetic waves. This paper uses FPGA as the processing core. The software mainly comprises a waveform generator, an Ethernet module, a memory module, a pulse generator, a pulse selector, a protection module, an error compensation module. A durability of shock absorbers is used as the testing platform. The durability mainly comprises a single electric cylinder, a servo motor for driving the electric cylinder, and the servo motor driver.

Adjustable expandable cryogenic piston and ring

DOEpatents

Mazur, Peter O.; Pallaver, Carl B.

1980-01-01

The operation of a reciprocating expansion engine for cryogenic refrigeration is improved by changing the pistons and rings so that the piston can be operated from outside the engine to vary the groove in which the piston ring is located. This causes the ring, which is of a flexible material, to be squeezed so that its contact with the wall is subject to external control. This control may be made manually or it may be made automatically in response to instruments that sense the amount of blow-by of the cryogenic fluid and adjust for an optimum blow-by.

Developmental Considerations on the Free-Piston Stirling Power Convertor for Use in Space

NASA Technical Reports Server (NTRS)

Schreiber, Jeffrey G.

2006-01-01

Free-piston Stirling power conversion has been considered a candidate for radioisotope power systems for space for more than a decade. Prior to the free-piston Stirling architecture, systems were designed with kinematic Stirling engines with rotary alternators to convert heat to electricity. These systems were proposed with lightly loaded linkages to achieve the necessary life. When the free-piston configuration was initially proposed, it was thought to be attractive due to the relatively high conversion efficiency, acceptable mass, and the potential for long life and high reliability. These features have consistently been recognized by teams that have studied technology options for radioisotope power systems. Since free-piston Stirling power conversion was first considered for space power applications, there have been major advances in three general areas of development: demonstration of life and reliability, the success achieved by Stirling cryocoolers in flight, and the overall developmental maturity of the technology for both flight and terrestrial applications. Based on these advances, free-piston Stirling convertors are currently being developed for a number of terrestrial applications. They commonly operate with the power, efficiency, life, and reliability as intended, and much of the development now centers on system integration. This paper will summarize the accomplishments of free-piston Stirling power conversion technology over the past decade, review the status, and discuss the challenges that remain.

Developmental Considerations on the Free-piston Stirling Power Convertor for Use in Space

NASA Technical Reports Server (NTRS)

Schreiber, Jeffrey G.

2007-01-01

Free-piston Stirling power conversion has been considered a candidate for radioisotope power systems for space for more than a decade. Prior to the free-piston Stirling architecture, systems were designed with kinematic Stirling engines with rotary alternators to convert heat to electricity. These systems were proposed with lightly loaded linkages to achieve the necessary life. When the free-piston configuration was initially proposed, it was thought to be attractive due to the relatively high conversion efficiency, acceptable mass, and the potential for long life and high reliability. These features have consistently been recognized by teams that have studied technology options for radioisotope power systems. Since free-piston Stirling power conversion was first considered for space power applications, there have been major advances in three general areas of development: demonstration of life and reliability, the success achieved by Stirling cryocoolers in flight, and the overall developmental maturity of the technology for both flight and terrestrial applications. Based on these advances, free-piston Stirling convertors are currently being developed for a number of terrestrial applications. They commonly operate with the power, efficiency, life, and reliability as intended, and much of the development now centers on system integration. This paper will summarize the accomplishments of free-piston Stirling power conversion technology over the past decade, review the status, and discuss the challenges that remain.

Continuous Gravity and Tilt Reveal Anomalous Pressure and Density Changes Associated With Gas Pistoning Within the Summit Lava Lake of Kīlauea Volcano, Hawai`i

NASA Astrophysics Data System (ADS)

Poland, Michael P.; Carbone, Daniele

2018-03-01

Gas piston events within the summit eruptive vent of Kīlauea Volcano, Hawai`i, are characterized by increases in lava level and by decreases in seismic energy release, spattering, and degassing. During 2010-2011, gas piston events were especially well manifested, with lava level rises of tens of meters over the course of several hours, followed by a sudden drop to preevent levels. The changes in lava level were accompanied by directly proportional changes in gravity, but ground deformation determined from tilt was anticorrelative. The small magnitude of the gravity changes, compared to the large changes in volume within the vent during gas pistons, suggests that pistoning involves the accumulation of a very low-density (100-200 kg/m3) foam at the top of the lava column. Co-event ground tilt indicates that rise in lava level is paradoxically associated with deflation (the opposite is usually true), which can be modeled as an increase in the gas content of the magma column between the source reservoir and the surface. Gas pistoning behavior is therefore associated with not only accumulation of a shallow magmatic foam but also more bubbles within the feeder conduit, probably due to the overall decrease in gas emissions from the lava lake during piston events.

Continuous gravity and tilt reveal anomalous pressure and density changes associated with gas pistoning within the summit lava lake of Kīlauea Volcano, Hawaiʻi

USGS Publications Warehouse

Poland, Michael; Carbone, Daniele

2018-01-01

Gas piston events within the summit eruptive vent of Kīlauea Volcano, Hawai‘i, are characterized by increases in lava level and by decreases in seismic energy release, spattering, and degassing. During 2010–2011, gas piston events were especially well manifested, with lava level rises of tens of meters over the course of several hours, followed by a sudden drop to preevent levels. The changes in lava level were accompanied by directly proportional changes in gravity, but ground deformation determined from tilt was anticorrelative. The small magnitude of the gravity changes, compared to the large changes in volume within the vent during gas pistons, suggests that pistoning involves the accumulation of a very low‐density (100–200 kg/m3) foam at the top of the lava column. Co‐event ground tilt indicates that rise in lava level is paradoxically associated with deflation (the opposite is usually true), which can be modeled as an increase in the gas content of the magma column between the source reservoir and the surface. Gas pistoning behavior is therefore associated with not only accumulation of a shallow magmatic foam but also more bubbles within the feeder conduit, probably due to the overall decrease in gas emissions from the lava lake during piston events.

Double acting stirling engine piston ring

DOEpatents

Howarth, Roy B.

1986-01-01

A piston ring design for a Stirling engine wherein the contact pressure between the piston and the cylinder is maintained at a uniform level, independent of engine conditions through a balancing of the pressure exerted upon the ring's surface and thereby allowing the contact pressure on the ring to be predetermined through the use of a preloaded expander ring.

Symmetry of the Adiabatic Condition in the Piston Problem

ERIC Educational Resources Information Center

Anacleto, Joaquim; Ferreira, J. M.

2011-01-01

This study addresses a controversial issue in the adiabatic piston problem, namely that of the piston being adiabatic when it is fixed but no longer so when it can move freely. It is shown that this apparent contradiction arises from the usual definition of adiabatic condition. The issue is addressed here by requiring the adiabatic condition to be…

Combined Heat & Power Using the Infinia Concentrated Solar - CHP PowerDish System

DTIC Science & Technology

2013-08-01

forward operating base FPSE Free Piston Stirling Engine GHG greenhouse gas IOU investor-owned utility kW kilowatt kWac kilowatt alternating...Free Piston Stirling Engine (FPSE) for military, commercial, and space applications for almost 30 years. As Infinia developed a commercial product...6 Figure 2. Free-piston Stirling generator. ................................................................................ 6 Figure 3

Turbocharger apparatus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leavesley, M.G.

1993-08-03

Variable turbocharger apparatus is described comprising a compressor housing, a compressor mounted for rotation in the compressor housing, a turbine housing, a turbine mounted for rotation in the turbine housing, a first inlet for enabling air to be conducted to the compressor, an outlet for air from the compressor, a second inlet for enabling exhaust gases from an engine to be conducted to the turbine, a chamber which surrounds the turbine and which receives the exhaust gases from the second inlet before the exhaust gases are conducted to the turbine, a piston which is positioned between the turbine and themore » turbine housing and which is slidable backwards and forwards to form a movable wall separating the turbine from the chamber which surrounds the turbine, a bearing assembly for allowing the rotation of the compressor and the turbine, and a heat shield for shielding the bearing assembly from the exhaust gases, the piston having a plurality of vanes, the piston being such that in its closed position it terminates short of an adjacent part of the turbine housing so that there is always a gap between the end of the piston and the adjacent part of the turbine housing whereby exhaust gases from the chamber can always pass through the gap to act on the turbine, the piston being such that in its open position the gap is increased, and the piston being biased to its closed position against pressure from exhaust gases in the chamber during use of the variable turbocharger apparatus whereby the piston slides backwards and forwards to vary the gap in dependence upon engine operating conditions, and the variable turbocharger apparatus being such that the vanes on the piston enter into slots in the heat shield.« less

[The length of the piston in otosclerosis surgery].

PubMed

Portmann, D; Alcantara, M; Vianna, M

2007-01-01

The measurement of the piston is always described as a significant stage of the surgery but its length is never clearly defined. The goal of this work is to determine the length of the prosthesis. From May 2003 to May 2005, 128 patients with otosclerosis, diagnosed on the basis of their clinical history and their audiogram, were included in this prospective study. Some of them were revision surgeries. The prosthesis generally used was the Portmann piston clip (Medtronic Xomed Inc Portmann Piston Clip Stainless Steel/Fluoroplastic). In stapedectomies, a Teflon piston of 0.6 mm of diameter was used (Pouret Company Fluoroplastic Stapes Prosthesis). These prostheses must be trimmed before their installation. The measurement technique is described. The length of the prosthesis was increased by 0.5 mm to include the thickness of the footplate. The Portmann piston clip was used 116 times (100 initial surgeries and 16 revisions surgeries) and the Teflon prosthesis of 0.6 mm of diameter only 13 times (6 primary stapedectomies and 7 revisions stapedectomies). The length of the prosthesis was between 3,5 mm and 5 mm. In the majority of cases, the length of the prosthesis was 4.75 mm (62 patients, 48.1%), followed by 4.5 mm (29 patients, 22.5%) and 5 mm (27 patients, 20.9%). In eleven cases (8.5%) the prosthesis measured less than 4,5 mm. None of the patients in this study experienced a postoperative sensorineural hearing loss. The measurement of the length of the piston is very significant, and in our study the majority of the pistons were cut at 4.75 mm which indicates an incus-footplate measurement of 4.25 mm.

Electromagnetic liquid pistons for capillarity-based pumping

NASA Astrophysics Data System (ADS)

Malouin, Bernard; Olles, Joseph; Cheng, Lili; Hirsa, Amir; Vogel, Michael

2011-11-01

Two adjoining ferrofluid droplets can behave as an electronically-controlled oscillator or switch by an appropriate balance of magnetic, capillary, and inertial forces. Their motion can be exploited to displace a surrounding liquid, forming electromagnetic liquid pistons. Such ferrofluid pistons can pump a precise volume of liquid via finely tunable amplitudes or resonant frequencies with no solid moving parts. Here we demonstrate the use of these liquid pistons in capillarity-dominated systems for variable focal distance liquid lenses with nearly perfect spherical interfaces. These liquid/liquid lenses feature many promising qualities not previously realized together in a liquid lens, including large apertures, immunity to evaporation, invariance to orientation relative to gravity, and low driving voltages. The dynamics of these liquid pistons is examined, with experimental measurements showing good agreement with a spherical cap model. A centimeter-scale lens was shown to respond in excess of 30 Hz, with resonant frequencies over 1 kHz predicted for scaled down systems.

Pump having pistons and valves made of electroactive actuators

NASA Technical Reports Server (NTRS)

Bar-Cohen, Yoseph (Inventor)

1997-01-01

The present invention provides a pump for inducing a displacement of a fluid from a first medium to a second medium, including a conduit coupled to the first and second media, a transducing material piston defining a pump chamber in the conduit and being transversely displaceable for increasing a volume of the chamber to extract the fluid from the first medium to the chamber and for decreasing the chamber volume to force the fluid from the chamber to the second medium, a first transducing material valve mounted in the conduit between the piston and the first medium and being transversely displaceable from a closed position to an open position to admit the fluid to the chamber, and control means for changing a first field applied to the piston to displace the piston for changing the chamber volume and for changing a second field applied to the first valve to change the position of the first valve.

Piston pump and method of reducing vapor lock

DOEpatents

Phillips, Benjamin A.; Harvey, Michael N.

2000-02-15

A pump includes a housing defining a cavity, at least one bore, a bore inlet, and a bore outlet. The bore extends from the cavity to the outlet and the inlet communicates with the bore at a position between the cavity and the outlet. A crankshaft is mounted in supports and has an eccentric portion disposed in the cavity. The eccentric portion is coupled to a piston so that rotation of the crankshaft reciprocates the piston in the bore between a discharge position an intake position. The bore may be offset from an axis of rotation to reduce bending of the piston during crankshaft rotation. During assembly of the pump, separate parts of the housing can be connected together to facilitate installation of internal pumping components. Also disclosed is a method of reducing vapor lock by mixing vapor and liquid portions of a substance and introducing the mixture into a piston bore.

Piston pump and method of reducing vapor lock

DOEpatents

Phillips, Benjamin A.; Harvey, Michael N.

2001-01-30

A pump includes a housing defining a cavity, at least one bore, a bore inlet, and a bore outlet. The bore extends from the cavity to the outlet and the inlet communicates with the bore at a position between the cavity and the outlet. A crankshaft is mounted in supports and has an eccentric portion disposed in the cavity. The eccentric portion is coupled to a piston so that rotation of the crankshaft reciprocates the piston in the bore between a discharge position an intake position. The bore may be offset from an axis of rotation to reduce bending of the piston during crankshaft rotation. During assembly of the pump, separate parts of the housing can be connected together to facilitate installation of internal pumping components. Also disclosed is a method of reducing vapor lock by mixing vapor and liquid portions of a substance and introducing the mixture into a piston bore.

1987 overview of free-piston Stirling technology for space power application

NASA Technical Reports Server (NTRS)

Slaby, Jack G.; Alger, Donald L.

1987-01-01

The Lewis Research Center program concerned with the development of a free-piston Stirling engine for space-power applications is examined. The system mass of a Stirling system is compared to that of a Brayton system for the same peak temperature and output power; the advantages of the Stirling system are discussed. The predicted and experimental performances of the 25 kWe opposed-piston space power demonstrator engine are evaluated. It is determined that in order to enhance performance the regenerator needs to be modified, and the gas bearing flow between the displacer and power piston needs to be isolated in order to increase the operating stroke. Identification and correction of the energy losses, the design and operation of the linear alternator, and heat exchange concepts are considered. The design parameters and conceptual design characteristics for a 25 kWe single-cylinder free-piston Stirling space-power converter are described.

Multiple-stage integrating accelerometer

DOEpatents

Devaney, H.F.

1984-06-27

An accelerometer assembly is provided for use in activating a switch in response to multiple acceleration pulses in series. The accelerometer includes a housing forming a chamber. An inertial mass or piston is slidably disposed in the chamber and spring biased toward a first or reset position. A damping system is also provided to damp piston movement in response to first and subsequent acceleration pulses. Additionally, a cam, including a Z-shaped slot, and cooperating follower pin slidably received therein are mounted to the piston and the housing. The middle or cross-over leg of the Z-shaped slot cooperates with the follower pin to block or limit piston movement and prevent switch activation in response to a lone acceleration pulse. The switch of the assembly is only activated after two or more separate acceleration pulses are sensed and the piston reaches the end of the chamber opposite the reset position.

Experimental study on heat transmission to the vestibule during CO2 laser use in revision stapes surgery.

PubMed

Szymański, M; Morshed, K; Mills, R

2007-01-01

We studied the transmission of heat to the vestibule during revision stapes surgery with a piston in situ, using a CO2 laser, in an in vitro model. A type K thermocouple was placed around the medial end of stainless steel and fluoroplastic wire pistons in a 'vestibule' filled with saline. The effect of laser hits on fluoroplastic wire and stainless steel stapes prostheses was investigated. The effect of introducing a vein graft to seal the stapedotomy was also examined. Greater temperature rises occurred with stainless steel than with fluoroplastic wire pistons. The addition of the vein graft reduced heat transmission. Application of the CO2 laser to fluoroplastic wire pistons, using the power settings suggested by the manufacturer, is not likely to damage the inner-ear structures. Application of 6 W laser energy to stainless steel pistons can potentially disturb the inner-ear function.

Miniature Fourier transform spectrometer with a dual closed-loop controlled electrothermal micromirror.

PubMed

Han, Fengtian; Wang, Wei; Zhang, Xiaoyang; Xie, Huikai

2016-10-03

A large piston-displacement electrothermal micromirror with closed-loop control of both piston scan and tilting of the mirror plate is demonstrated for use in a miniature Fourier transform spectrometer. Constant scan velocity in an ultra large piston scan range has been demonstrated by the proposed closed-loop piston control scheme which can be easily implemented without considerably increasing system complexity. The experimental results show that the usable linear scan range generated by the micromirror has been extended up to 505 μm. The measured spectral resolution in a compact spectrometer reaches 20 cm^-1, or 0.57 nm at 532 nm wavelength. Compared to other presented systems, this microspectrometer will benefit from the closed-loop thermal actuator approach utilizing both the piston servo and tilt control to provide more consistent spectral response, improved spectral resolution and enhanced robustness to disturbances.

Calibration and comparison of the NASA Lewis free-piston Stirling engine model predictions with RE-1000 test data

NASA Technical Reports Server (NTRS)

Geng, Steven M.

1987-01-01

A free-piston Stirling engine performance code is being upgraded and validated at the NASA Lewis Research Center under an interagency agreement between the Department of Energy's Oak Ridge National Laboratory and NASA Lewis. Many modifications were made to the free-piston code in an attempt to decrease the calibration effort. A procedure was developed that made the code calibration process more systematic. Engine-specific calibration parameters are often used to bring predictions and experimental data into better agreement. The code was calibrated to a matrix of six experimental data points. Predictions of the calibrated free-piston code are compared with RE-1000 free-piston Stirling engine sensitivity test data taken at NASA Lewis. Reasonable agreement was obtained between the code prediction and the experimental data over a wide range of engine operating conditions.

Calibration and comparison of the NASA Lewis free-piston Stirling engine model predictions with RE-1000 test data

NASA Technical Reports Server (NTRS)

Geng, Steven M.

1987-01-01

A free-piston Stirling engine performance code is being upgraded and validated at the NASA Lewis Research Center under an interagency agreement between the Department of Energy's Oak Ridge National Laboratory and NASA Lewis. Many modifications were made to the free-piston code in an attempt to decrease the calibration effort. A procedure was developed that made the code calibration process more systematic. Engine-specific calibration parameters are often used to bring predictions and experimental data into better agreement. The code was calibrated to a matrix of six experimental data points. Predictions of the calibrated free-piston code are compared with RE-1000 free-piston Stirling engine sensitivity test data taken at NASA Lewis. Resonable agreement was obtained between the code predictions and the experimental data over a wide range of engine operating conditions.

Update on results of SPRE testing at NASA Lewis

NASA Technical Reports Server (NTRS)

Cairelli, James E.; Swec, Diane M.; Wong, Wayne A.; Doeberling, Thomas J.; Madi, Frank J.

1991-01-01

The Space Power Research Engine (SPRE), a free-piston Stirling engine with a linear alternator, is being tested at NASA Lewis Research Center as part of the Civilian Space Technology Initiative (CSTI) as a candidate for high capacity space power. Results are presented from recent SPRE tests designed to investigated the effects of variation in the displacer seal clearance and piston centering port area on engine performance and dynamics. The impact of these variations on PV power and efficiency are presented. Comparisons of the displacer seal clearance tests results with HFAST code predictions show good agreement for PV power, but show poor agreement for PV efficiency. Correlations are presented relating the piston midstroke position to the dynamic Delta P across the piston and the centering port area. Test results indicate that a modest improvement in PV power and efficiency may be realized with a reduction in piston centering port area.

Update on results of SPRE testing at NASA Lewis

NASA Technical Reports Server (NTRS)

Cairelli, James E.; Swec, Diane M.; Wong, Wayne A.; Doeberling, Thomas J.; Madi, Frank J.

1991-01-01

The Space Power Research Engine (SPRE), a free-piston Stirling engine with a linear alternator, is being tested at NASA Lewis Research Center as part of the Civilian Space Technology Initiative (CSTI) as a candidate for high capacity space power. Results are presented from recent SPRE tests designed to investigate the effects of variation in the displacer seal clearance and piston centering port area on engine performance and dynamics. The effects of these variations on PV power and efficiency are presented. Comparisons of the displacer seal clearance test results with HFAST code predictions show good agreement for PV power but poor agreement for PV efficiency. Correlations are presented relating the piston mid-stroke position to the dynamic Delta P across the piston and the centering port area. Test results indicate that a modest improvement in PV power and efficiency may be realized with a reduction in piston centering port area.

Adaptive individual-cylinder thermal state control using piston cooling for a GDCI engine

DOEpatents

Roth, Gregory T; Husted, Harry L; Sellnau, Mark C

2015-04-07

A system for a multi-cylinder compression ignition engine includes a plurality of nozzles, at least one nozzle per cylinder, with each nozzle configured to spray oil onto the bottom side of a piston of the engine to cool that piston. Independent control of the oil spray from the nozzles is provided on a cylinder-by-cylinder basis. A combustion parameter is determined for combustion in each cylinder of the engine, and control of the oil spray onto the piston in that cylinder is based on the value of the combustion parameter for combustion in that cylinder. A method for influencing combustion in a multi-cylinder engine, including determining a combustion parameter for combustion taking place in in a cylinder of the engine and controlling an oil spray targeted onto the bottom of a piston disposed in that cylinder is also presented.

Imparting Motion to a Test Object Such as a Motor Vehicle in a Controlled Fashion

NASA Technical Reports Server (NTRS)

Southward, Stephen C. (Inventor); Reubush, Chandler (Inventor); Pittman, Bryan (Inventor); Roehrig, Kurt (Inventor); Gerard, Doug (Inventor)

2014-01-01

An apparatus imparts motion to a test object such as a motor vehicle in a controlled fashion. A base has mounted on it a linear electromagnetic motor having a first end and a second end, the first end being connected to the base. A pneumatic cylinder and piston combination have a first end and a second end, the first end connected to the base so that the pneumatic cylinder and piston combination is generally parallel with the linear electromagnetic motor. The second ends of the linear electromagnetic motor and pneumatic cylinder and piston combination being commonly linked to a mount for the test object. A control system for the linear electromagnetic motor and pneumatic cylinder and piston combination drives the pneumatic cylinder and piston combination to support a substantial static load of the test object and the linear electromagnetic motor to impart controlled motion to the test object.

Arctic Ocean Paleoceanography and Future IODP Drilling

NASA Astrophysics Data System (ADS)

Stein, Ruediger

2015-04-01

Although the Arctic Ocean is a major player in the global climate/earth system, this region is one of the last major physiographic provinces on Earth where the short- and long-term geological history is still poorly known. This lack in knowledge is mainly due to the major technological/logistical problems in operating within the permanently ice-covered Arctic region which makes it difficult to retrieve long and undisturbed sediment cores. Prior to 2004, in the central Arctic Ocean piston and gravity coring was mainly restricted to obtaining near-surface sediments, i.e., only the upper 15 m could be sampled. Thus, all studies were restricted to the late Pliocene/Quaternary time interval, with a few exceptions. These include the four short cores obtained by gravity coring from drifting ice floes over the Alpha Ridge, where older pre-Neogene organic-carbon-rich muds and laminated biosiliceous oozes were sampled. Continuous central Arctic Ocean sedimentary records, allowing a development of chronologic sequences of climate and environmental change through Cenozoic times and a comparison with global climate records, however, were missing prior to the IODP Expedition 302 (Arctic Ocean Coring Expedition - ACEX), the first scientific drilling in the central Arctic Ocean. By studying the unique ACEX sequence, a large number of scientific discoveries that describe previously unknown Arctic paleoenvironments, were obtained during the last decade (for most recent review and references see Stein et al., 2014). While these results from ACEX were unprecedented, key questions related to the climate history of the Arctic Ocean remain unanswered, in part because of poor core recovery, and in part because of the possible presence of a major mid-Cenozoic hiatus or interval of starved sedimentation within the ACEX record. In order to fill this gap in knowledge, international, multidisciplinary expeditions and projects for scientific drilling/coring in the Arctic Ocean are needed. Key areas and approaches for drilling and recovering undisturbed and complete sedimentary sequences are depth transects across the major ocean ridge systems, such as the Lomonosov Ridge. These new detailed climate records spanning time intervals from the (late Cretaceous/)Paleogene Greenhouse world to the Neogene-Quaternary Icehouse world will give new insights into our understanding of the Arctic Ocean within the global climate system and provide an opportunity to test the performance of climate models used to predict future climate change. During the Polarstern Expedition PS87 in August-September 2014, new site survey data including detailed multibeam bathymetry, multi-channel seismic and Parasound profiling as well as geological coring, were obtained on Lomonosov Ridge (Stein, 2015), being the basis for a more precise planning and update for a future IODP drilling campaign. Reference: Stein, R. (Ed.), 2015. Cruise Report of Polarstern Expedition PS87-2014 (Arctic Ocean/Lomonosov Ridge). Reps. Pol. Mar. Res., in press. Stein, R. , Weller, P. , Backman, J. , Brinkhuis, H., Moran, K. , Pälike, H., 2014. Cenozoic Arctic Ocean Climate History: Some highlights from the IODP Arctic Coring Expedition (ACEX). Developments in Marine Geology 7, Elsevier Amsterdam/New York, pp. 259-293.

75 FR 3418 - Airworthiness Directives; British Aerospace Regional Aircraft Model HP.137 Jetstream Mk.1...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-21

... tightening torque are contained in APPH SB 32-76 Revision 1. As a result, pistons which were previously... formula for calculating the piston safe life. This calculation and a revised end fitting tightening torque... piston rod adjacent to the eye-end. This was caused by excessive torque which had been applied to the eye...

Pressure Regulators as Valves for Saving Compressed Air and their Influence on System Dynamics

NASA Astrophysics Data System (ADS)

Dvořák, Lukáš; Fojtášek, Kamil

2015-05-01

Pressure regulators in the field of pneumatic mechanisms can be used as valves for saving compressed air. For example it can be used to reduce the pressure when the piston rod is retracting unloaded and thus it is possible to save some energy. However the problem is that saving valve can significantly affect the dynamics of the pneumatic system. The lower pressure in the piston rod chamber causes extension of time for retraction of the piston rod. This article compare the air consumption experimentally determined and calculated, measured curves of pressure in cylinder chambers and piston speed when saving valve is set up differently.

Acoustic radiation efficiency of a periodically corrugated rigid piston

NASA Astrophysics Data System (ADS)

Estrada, Héctor; Uris, Antonio; Meseguer, Francisco

2012-09-01

The radiation of sound by a periodically corrugated rigid piston is explored using theoretical and numerical approaches and compared with the radiation of flat rigid piston. The depth and the period of the corrugation are considered to be comparable with the wavelength in the surrounding fluid. Radiation enhancement is predicted due to cavity resonances and coherent diffraction. In addition, broad regions of low radiation efficiency are observed. Both effects could have an impact in acoustic transducers technology, either to increase the piston radiated power or to create a source of evanescent acoustic waves. The possibilities offered by this strategy in the nonlinear acoustic regime are also briefly discussed.

Vibration isolation in a free-piston driven expansion tube facility

NASA Astrophysics Data System (ADS)

Gildfind, D. E.; Jacobs, P. A.; Morgan, R. G.

2013-09-01

The stress waves produced by rapid piston deceleration are a fundamental feature of free-piston driven expansion tubes, and wave propagation has to be considered in the design process. For lower enthalpy test conditions, these waves can traverse the tube ahead of critical flow processes, severely interfering with static pressure measurements of the passing flow. This paper details a new device which decouples the driven tube from the free-piston driver, and thus prevents transmission of stress waves. Following successful incorporation of the concept in the smaller X2 facility, it has now been applied to the larger X3 facility, and results for both facilities are presented.

The provision of clearances accuracy in piston - cylinder mating

NASA Astrophysics Data System (ADS)

Glukhov, V. I.; Shalay, V. V.

2017-08-01

The paper is aimed at increasing the quality of the pumping equipment in oil and gas industry. The main purpose of the study is to stabilize maximum values of productivity and durability of the pumping equipment based on the selective assembly of the cylinder-piston kinematic mating by optimization criterion. It is shown that the minimum clearance in the piston-cylinder mating is formed by maximum material dimensions. It is proved that maximum material dimensions are characterized by their own laws of distribution within the tolerance limits for the diameters of the cylinder internal mirror and the outer cylindrical surface of the piston. At that, their dispersion zones should be divided into size groups with a group tolerance equal to half the tolerance for the minimum clearance. The techniques for measuring the material dimensions - the smallest cylinder diameter and the largest piston diameter according to the envelope condition - are developed for sorting them into size groups. Reliable control of the dimensions precision ensures optimal minimum clearances of the piston-cylinder mating in all the size groups of the pumping equipment, necessary for increasing the equipment productivity and durability during the production, operation and repair processes.

The sperm pump of the hangingfly Bittacus planus Cheng (Mecoptera: Bittacidae).

PubMed

Gao, Qiong-Hua; Hua, Bao-Zhen

2015-11-01

The males of antliophoran insects usually use a sperm pump to transfer liquid sperm into the reproductive tract of the female. However, the fine structure of the sperm pump and its ejaculatory mechanism has not been thoroughly clarified in many groups of Mecoptera. In this paper, the structure of the sperm pump was investigated in the hangingfly Bittacus planus Cheng, 1949 using light and scanning electron microscopy. The sperm pump mainly consists of a piston fused with a piston-carrying sclerite, a pumping chamber enclosed by the genital folds, which comprises the posterior region of the ejaculatory sac, an ostial sclerite, a phallobase, and other associated structures and muscles. The piston crown plays a major role in the piston movement. The ostial sclerite serves as a discharge valve and is controlled by two antagonistic muscles. No depressor muscles were found attached to the piston. The sperm pumping activity is mainly controlled by the combination of the levator of the piston and the retractor and protractor of the ostial sclerite. The ejaculatory mechanism and phylogenetic significance are briefly discussed based on the structure of the sperm pump. Copyright © 2015 Elsevier Ltd. All rights reserved.

Overview of the 1986 free-piston Stirling SP-100 activities at the NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1986-01-01

An overview of the NASA Lewis Research Center SP-100 free-piston Stirling engine activities is presented. These activities include a free-piston Stirling space-power technology feasibility demonstration project as part of the SP-100 program being conducted in support of the Department of Defennse (DOD), Department of Energy (DOE), and NASA. The space-power Stirling advanced technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including test results. Future space-power projections are presented along with a description of a study that will investigate the feasibility of scaling a single-cylinder free-piston Stirling space-power module to the 150 kW power range. Design parameters and conceptual design features will be presented for a 25 kWe, single-cylinder free-piston Stirling space-power converter. A description of a hydrodynamic gas bearing concept is presented whereby the displacer of a 1 kWe free-piston Stirling engine is modified to demonstrate the bearing concept. And finally the goals of a conceptual design for a 25 kWe Solar Advanced Stirling Conversion System capable of delivering electric power to an electric utility grid are discussed.

Analysis of thermal stress of the piston during non-stationary heat flow in a turbocharged Diesel engine

NASA Astrophysics Data System (ADS)

Gustof, P.; Hornik, A.

2016-09-01

In the paper, numeric calculations of thermal stresses of the piston in a turbocharged Diesel engine in the initial phase of its work were carried out based on experimental studies and the data resulting from them. The calculations were made using a geometrical model of the piston in a five-cylinder turbocharged Diesel engine with a capacity of about 2300 cm3, with a direct fuel injection to the combustion chamber and a power rating of 85 kW. In order to determine the thermal stress, application of own mathematical models of the heat flow in characteristic surfaces of the piston was required to show real processes occurring on the surface of the analysed component. The calculations were performed using a Geostar COSMOS/M program module. A three-dimensional geometric model of the piston was created in this program based on a real component, in order to enable the calculations and analysis of thermal stresses during non-stationary heat flow. Modelling of the thermal stresses of the piston for the engine speed n=4250 min-1 and engine load λ=1.69 was carried out.

Overview of the 1986 free-piston Stirling SP-100 activities at the NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1986-01-01

An overview of the NASA Lewis Research Center SP-100 free-piston Stirling engine activities is presented. These activities include a free-piston Stirling space-power technology feasibility demonstration project as part of the SP-100 program being conducted in support of the Department of Defense (DOD), Department of Energy (DOE), and NASA. The space-power Stirling advanced technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including test results. Future space-power projections are presented along with a description of a study that will investigate the feasibility of scaling a single-cylinder free-piston Stirling space-power module to the 150 kW power range. Design parameters and conceptual design features will be presented for a 25 kWe, single-cylinder free-piston Stirling space-power converter. A description of a hydrodynamic gas bearing concept is presented whereby the displacer of a 1 kWe free-piston Stirling engine is modified to demonstrate the bearing concept. And finally the goals of a conceptual design for a 25 kWe Solar Advanced Stirling Conversion System capable of delivering electric power to an electric utility grid are discussed.

Hydraulically-activated operating system for an electric circuit breaker

DOEpatents

Imam, Imdad; Barkan, Philip

1979-01-01

This operating system comprises a fluid motor having a piston, a breaker-opening space at one side of the piston, and a breaker-closing space at its opposite side. An accumulator freely communicates with the breaker-opening space for supplying pressurized fluid thereto during a circuit-breaker opening operation. A normally-closed valve located on the breaker-closing-side of the piston is openable to release liquid from the breaker-closing space so that pressurized liquid in the breaker-opening space can drive the piston in an opening direction. Means is provided for restoring the valve to its closed position following the circuit-breaker opening operation. An impeded passage affords communication between the accumulator and the breaker-closing space to allow pressurized liquid to flow from the accumulator to the breaker-closing space and develop a pressure therein substantially equal to accumulator pressure when the valve is restored to closed position following breaker-opening. This passage is so impeded that the flow therethrough from the accumulator into the breaker-closing space is sufficiently low during initial opening motion of the piston through a substantial portion of its opening stroke as to avoid interference with said initial opening motion of the piston.

A Model For the Limiting Time in Vortex Ring Formation

NASA Technical Reports Server (NTRS)

Shariff, Karim; Gharib, Morteza; Rambod, Edmond; Merriam, Marshal (Technical Monitor)

1997-01-01

In another presentation, Gharib et at provide experimental results to show that when a vortex ring is created from a pipe by a piston, there is a limiting time or piston stroke length beyond which multiple rings appear. This time appeared to be insensitive to piston velocity history and Reynolds number. Nature might exploit such a. limit in different contexts to coherently deliver mass or momentum flux with the least number of strokes. Here, a simple hypothesis is considered: the limiting time occurs when the apparatus is no longer able to deliver energy at a rate compatible with the requirement, due to Kelvin, that a steady vortex ring have maximum energy given circulation and impulse. More specifically, the limit is expected to occur when the quantity alpha = E/square root of Gamma(sup 3)I delivered by the piston drops below the value, alpha(sub lim) for a limiting steady vortex ring solution. The resulting predictions agree very well with the experiments (after using alpha(sub lim) measured using the experimental flow fields). The insensitivity to piston history also emerges from the model. Finally, piston histories are designed that may extend the limiting time somewhat.

Measurement of liquid film thickness by optical fluorescence and its application to an oscillating piston positive displacement flowmeter

NASA Astrophysics Data System (ADS)

Morton, Charlotte E.; Baker, Roger C.; Hutchings, Ian M.

2011-12-01

The movement of the circular piston in an oscillating piston positive displacement flowmeter is important in understanding the operation of the flowmeter, and the leakage of liquid past the piston plays a key role in the performance of the meter. The clearances between the piston and the chamber are small, typically less than 60 µm. In order to measure this film thickness a fluorescent dye was added to the water passing through the meter, which was illuminated with UV light. Visible light images were captured with a digital camera and analysed to give a measure of the film thickness with an uncertainty of less than 7%. It is known that this method lacks precision unless careful calibration is undertaken. Methods to achieve this are discussed in the paper. The grey level values for a range of film thicknesses were calibrated in situ with six dye concentrations to select the most appropriate one for the range of liquid film thickness. Data obtained for the oscillating piston flowmeter demonstrate the value of the fluorescence technique. The method is useful, inexpensive and straightforward and can be extended to other applications where measurement of liquid film thickness is required.

An early to mid-Pleistocene deep Arctic Ocean ostracode fauna with North Atlantic affinities

USGS Publications Warehouse

DeNinno, Lauren H.; Cronin, Thomas M.; Rodriquez-Lazaro, J.; Brenner, Alec R.

2015-01-01

An early to middle Pleistocene ostracode fauna was discovered in sediment core P1-93-AR-23 (P23, 76.95°N, 155.07°W) from 951 meter water depth from the Northwind Ridge, western Arctic Ocean. Piston core P23 yielded more than 30,000 specimens and a total of about 30 species. Several early to mid-Pleistocene species in the genera Krithe,Echinocythereis, Pterygocythereis, and Arcacythere are now extinct in the Arctic and show taxonomic affinities to North Atlantic Ocean species. Our results suggest that there was a major ostracode faunal turnover during the global climate transitions known as the Mid-Pleistocene Transition (MPT, ~ 1.2 to 0.7 Ma) and the Mid-Brunhes Event (MBE, ~ 400 ka) reflecting the development of perennial sea ice during interglacial periods and large ice shelves during glacial periods over the last 400,000 years.

Large-Scale Compute-Intensive Analysis via a Combined In-situ and Co-scheduling Workflow Approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Messer, Bronson; Sewell, Christopher; Heitmann, Katrin

2015-01-01

Large-scale simulations can produce tens of terabytes of data per analysis cycle, complicating and limiting the efficiency of workflows. Traditionally, outputs are stored on the file system and analyzed in post-processing. With the rapidly increasing size and complexity of simulations, this approach faces an uncertain future. Trending techniques consist of performing the analysis in situ, utilizing the same resources as the simulation, and/or off-loading subsets of the data to a compute-intensive analysis system. We introduce an analysis framework developed for HACC, a cosmological N-body code, that uses both in situ and co-scheduling approaches for handling Petabyte-size outputs. An initial inmore » situ step is used to reduce the amount of data to be analyzed, and to separate out the data-intensive tasks handled off-line. The analysis routines are implemented using the PISTON/VTK-m framework, allowing a single implementation of an algorithm that simultaneously targets a variety of GPU, multi-core, and many-core architectures.« less

Marine sedimentary coring and high-quality, multi-proxy records in the high-latitude North Pacific: a synthesis of paleoceanographic cruise and research effort

NASA Astrophysics Data System (ADS)

Borreggine, M. J.; Myhre, S. E.; Smith-Mislan, A.; Davis, C. V.; Deutsch, C.

2016-12-01

We assessed sedimentary coring efforts, data acquisition and publications from the subpolar North Pacific and marginal seas from 1951-2015. We found a total of 1,249 sediment cores collected by American, French, Japanese and Russian research vessels across the Subarctic Pacific (639 cores), Alaskan Gyre (8 cores), Sea of Okhotsk (270 cores), Bering Sea (120 cores), and the Sea of Japan (212 cores). Of these, 27% are investigated in peer-reviewed publications; this fraction varies from the Subarctic Pacific (18%), Alaskan Gyre (100%), Sea of Okhotsk (33%), Bering Sea (57%), and the Sea of Japan (25%). We assess the biological, geochemical, isotopic, and stratigraphic lines of evidence available for these cores, alongside coring technology, location, depth, cruise and vessel metadata. Coring effort peaked in 1996, 2009, and 2010 where 86, 90, and 67 cores, respectively, were recovered in the five regions collectively. Piston cores are the most common (347 cores) of the 24 different coring technologies used in the last 64 years. Published sedimentation rates range across the Subarctic Pacific (0.132-208 cm/ka), Alaskan Gyre (9-10,000 cm/ka), Sea of Okhotsk (0.7-115.5 cm/ka), Bering Sea (3-250 cm/ka), and the Sea of Japan (0.5-25 cm/ka), with the highest rates in the Alaskan Gyre. Age model development has transitioned from singular techniques to multiproxy approaches. Recent chronologies are built using a mix of isotope stratigraphy, radiocarbon dating, magnetostratigraphy, biostratigraphy, tephrochronology, % opal, color, and lithophysical proxies. Out of 275 published chronologies for the North Pacific, 132 (48%) are built with radiocarbon dating. Sedimentary data in the North Pacific includes biological, geochemical, isotopic, and stratigraphic analyses, and we document all proxy evidence to-date across all cores assessed. This database of coring and publication provides a unique resource and comprehensive assessment to the paleoceanographic community, can be used to identify strengths and weaknesses in North Pacific paleoceanography, and will be made publicly available. Additionally, the database is used to recreate past sea ice, temperature, and oxygen conditions in two additional submissions at the 2016 AGU Fall Meeting.

Acoustic ground impedance meter

NASA Technical Reports Server (NTRS)

Zuckerwar, A. J.

1981-01-01

A compact, portable instrument was developed to measure the acoustic impedance of the ground, or other surfaces, by direct pressure-volume velocity measurement. A Helmholz resonator, constructed of heavy-walled stainless steel but open at the bottom, is positioned over the surface having the unknown impedance. The sound source, a cam-driven piston of known stroke and thus known volume velocity, is located in the neck of the resonator. The cam speed is a variable up to a maximum 3600 rpm. The sound pressure at the test surface is measured by means of a microphone flush-mounted in the wall of the chamber. An optical monitor of the piston displacement permits measurement of the phase angle between the volume velocity and the sound pressure, from which the real and imaginary parts of the impedance can be evaluated. Measurements using a 5-lobed cam can be made up to 300 Hz. Detailed design criteria and results on a soil sample are presented.

Comparative electron microscopic study of the surface structure of gold, Teflon, and titanium stapes prostheses.

PubMed

Kwok, P; Fisch, U; Strutz, J; Jacob, P

2001-09-01

The goal of this study was to compare stapes prostheses of different materials with respect to their surface structures and to discuss their suitability for their use in stapes surgery. The surface condition of a stapes prosthesis plays an important role in relation to the type of membrane that forms between the stapes piston and the bony edge of the stapedotomy opening. The quality of this membrane in thickness and mobility is one of the determinants for postoperative hearing improvement. The surface conditions of gold, Teflon/steel, Teflon/platinum, and titanium stapes prostheses were examined with a scanning electron microscope. The loop, shaft, and end of each prosthesis were studied. The gold piston was the smoothest of the four pistons examined. When it was cut with a scalpel, a very smooth surface was achieved at the end area. The Teflon piston had the roughest surface. However, when it was cut, a smooth surface with a parallel arrangement of fibers resulted. Its steel loop was the smoothest, followed by gold and platinum. The titanium shaft had a scaly surface, which remained when the end of the shaft was shortened. Because a certain roughness of the piston surface is necessary for the development of a stable membrane between the piston and the edge of the stapedotomy opening, the titanium prosthesis is considered to be the most suitable for stapes surgery of the three pistons examined.

Radial-piston pump for drive of test machines

NASA Astrophysics Data System (ADS)

Nizhegorodov, A. I.; Gavrilin, A. N.; Moyzes, B. B.; Cherkasov, A. I.; Zharkevich, O. M.; Zhetessova, G. S.; Savelyeva, N. A.

2018-01-01

The article reviews the development of radial-piston pump with phase control and alternating-flow mode for seismic-testing platforms and other test machines. The prospects for use of the developed device are proved. It is noted that the method of frequency modulation with the detection of the natural frequencies is easily realized by using the radial-piston pump. The prospects of further research are given proof.

Control scheme for power modulation of a free piston Stirling engine

DOEpatents

Dhar, Manmohan

1989-01-01

The present invention relates to a control scheme for power modulation of a free-piston Stirling engine-linear alternator power generator system. The present invention includes connecting an autotransformer in series with a tuning capacitance between a linear alternator and a utility grid to maintain a constant displacement to piston stroke ratio and their relative phase angle over a wide range of operating conditions.

Metal-silicate Partitioning at High Pressure and Temperature: Experimental Methods and a Protocol to Suppress Highly Siderophile Element Inclusions.

PubMed

Bennett, Neil R; Brenan, James M; Fei, Yingwei

2015-06-13

Estimates of the primitive upper mantle (PUM) composition reveal a depletion in many of the siderophile (iron-loving) elements, thought to result from their extraction to the core during terrestrial accretion. Experiments to investigate the partitioning of these elements between metal and silicate melts suggest that the PUM composition is best matched if metal-silicate equilibrium occurred at high pressures and temperatures, in a deep magma ocean environment. The behavior of the most highly siderophile elements (HSEs) during this process however, has remained enigmatic. Silicate run-products from HSE solubility experiments are commonly contaminated by dispersed metal inclusions that hinder the measurement of element concentrations in the melt. The resulting uncertainty over the true solubility and metal-silicate partitioning of these elements has made it difficult to predict their expected depletion in PUM. Recently, several studies have employed changes to the experimental design used for high pressure and temperature solubility experiments in order to suppress the formation of metal inclusions. The addition of Au (Re, Os, Ir, Ru experiments) or elemental Si (Pt experiments) to the sample acts to alter either the geometry or rate of sample reduction respectively, in order to avoid transient metal oversaturation of the silicate melt. This contribution outlines procedures for using the piston-cylinder and multi-anvil apparatus to conduct solubility and metal-silicate partitioning experiments respectively. A protocol is also described for the synthesis of uncontaminated run-products from HSE solubility experiments in which the oxygen fugacity is similar to that during terrestrial core-formation. Time-resolved LA-ICP-MS spectra are presented as evidence for the absence of metal-inclusions in run-products from earlier studies, and also confirm that the technique may be extended to investigate Ru. Examples are also given of how these data may be applied.

Geochronology and paleoceanographic history of Quaternary sediments from southwestern part of Pacific-Antarctic Ridge, the Ross Sea, Antarctica

NASA Astrophysics Data System (ADS)

Murayama, M.; Yagi, Y.; Mishima, T.; Horikawa, K.; Sagawa, T.; Kodama, K.; Kato, Y.; Minagawa, M.

2006-12-01

Paleoceanographic studies in the southern hemisphere high latitudes are important for understanding the global climate system. These detailed records of the oceanic response to various climate conditions are well- documented in marine sediments. The main goal of this study is to construct the precise chronostratigraphy and to reveal the paleocenographic and sedimentological changes in this region during Quaternary. A piston core SX-09 (65 10.79' S, 174 04.77' W, 3336 m water depth) which was recovered from southwestern part of Pacific-Antarctic Ridge, the Ross Sea, Antarctica during the R/V Hakuho-Maru KH02-4 cruise, was composed mainly of foraminifer bearing siliceous clay with ice-rafted debris (IRDs). To date, magnetostratigraphy and benthic foraminifer oxygen isotope were adopted. Remanent magnetization of the U-channel samples was measured with a 2G superconducting rock magnetometer. Stable characteristic remanent magnetization was isolated by subjecting the samples to progressive alternating field demagnezation. By referring the obtained magnetic polarity sequence with the geomagnetic polarity time scale (GPTS) by Cande and Kent (2005), we estimated the age of this core. Epoch boundary placed the Brouhes-Matuyama at 0.78 Ma was existed between 565 to 720 cmbsf. This suggested that the boundary was affected by IRDs distribution and/or by high sedimentation rate. The depth of 720 cmbsf to the bottom (1480 cm) was correlated with reverse of Matuyama Chron (Chrons C1r, ~2.58 Ma). Jaramillo Subchron (Chron C1r. 1n, 0.99-1.07 Ma) correlated clearly with the depths of 1012-1076 cmbsf. The average sedimentation rate calculated by the epoch boundary ages was approximately 0.7-1.5 cm/kyr. We will discuss more detail age control combined with d-18O data and the IRDs abundance corresponded to the glacial history in the Antarctic Sea.

Metal-silicate Partitioning at High Pressure and Temperature: Experimental Methods and a Protocol to Suppress Highly Siderophile Element Inclusions

PubMed Central

Bennett, Neil R.; Brenan, James M.; Fei, Yingwei

2015-01-01

Estimates of the primitive upper mantle (PUM) composition reveal a depletion in many of the siderophile (iron-loving) elements, thought to result from their extraction to the core during terrestrial accretion. Experiments to investigate the partitioning of these elements between metal and silicate melts suggest that the PUM composition is best matched if metal-silicate equilibrium occurred at high pressures and temperatures, in a deep magma ocean environment. The behavior of the most highly siderophile elements (HSEs) during this process however, has remained enigmatic. Silicate run-products from HSE solubility experiments are commonly contaminated by dispersed metal inclusions that hinder the measurement of element concentrations in the melt. The resulting uncertainty over the true solubility and metal-silicate partitioning of these elements has made it difficult to predict their expected depletion in PUM. Recently, several studies have employed changes to the experimental design used for high pressure and temperature solubility experiments in order to suppress the formation of metal inclusions. The addition of Au (Re, Os, Ir, Ru experiments) or elemental Si (Pt experiments) to the sample acts to alter either the geometry or rate of sample reduction respectively, in order to avoid transient metal oversaturation of the silicate melt. This contribution outlines procedures for using the piston-cylinder and multi-anvil apparatus to conduct solubility and metal-silicate partitioning experiments respectively. A protocol is also described for the synthesis of uncontaminated run-products from HSE solubility experiments in which the oxygen fugacity is similar to that during terrestrial core-formation. Time-resolved LA-ICP-MS spectra are presented as evidence for the absence of metal-inclusions in run-products from earlier studies, and also confirm that the technique may be extended to investigate Ru. Examples are also given of how these data may be applied. PMID:26132380

Foot pedal operated fluid type exercising device

NASA Technical Reports Server (NTRS)

Crum, G. W.; Sauter, R. J. (Inventor)

1973-01-01

A foot pedal operated exercising device is reported that contains a dynamometer formed of a pair of cylinders each containing a piston. The pistons are linked to each other. The upper portions of the two cylinders are joined together by a common opening to provide a common fluid reservoir and each piston is provided with a one way check valve to maintain an adequate supply of working fluid. Fluid from the driven cylinder is transmitted to the other cylinder through separate constant force spring biased valves each valve takes the predominant portion of the pressure drop thereby providing a constant force hydraulic dynamometer. A device is provided to determine the amount of movement of piston travel.

Numerical modelling of physical processes in a ballistic laboratory setup with a tapered adapter and plastic piston used for obtaining high muzzle velocities

NASA Astrophysics Data System (ADS)

Bykov, N. V.

2014-12-01

Numerical modelling of a ballistic setup with a tapered adapter and plastic piston is considered. The processes in the firing chamber are described within the framework of quasi- one-dimensional gas dynamics and a geometrical law of propellant burn by means of Lagrangian mass coordinates. The deformable piston is considered to be an ideal liquid with specific equations of state. The numerical solution is obtained by means of a modified explicit von Neumann scheme. The calculation results given show that the ballistic setup with a tapered adapter and plastic piston produces increased shell muzzle velocities by a factor of more than 1.5-2.

Bi-directionally draining pore fluid extraction vessel

DOEpatents

Prizio, Joseph; Ritt, Alexander; Mower, Timothy E.; Rodine, Lonn

1991-01-01

The invention is used to extract pore fluid from porous solids through a combination of mechanical compression and inert-gas injection and comprises a piston for axially compressing samples to force water out, and top and bottom drainage plates for capturing the exuded water and using inert gas to force water to exit when the limits of mechanical compression have been reached.

Braking system for use with an arbor of a microscope

DOEpatents

Norgren, Duane U.

1984-01-01

A balanced braking system comprising a plurality of braking assemblies located about a member to be braked. Each of the braking assemblies consists of a spring biased piston of a first material fitted into a body of a different material which has a greater contraction upon cooling than the piston material. The piston is provided with a recessed head portion over which is positioned a diaphragm and forming a space therebetween to which is connected a pressurized fluid supply. The diaphragm is controlled by the fluid in the space to contact or withdraw from the member to be braked. A cooling device causes the body within which the piston is fitted to contract more than the piston, producing a tight shrink fit therebetween. The braking system is particularly applicable for selectively braking an arbor of an electron microscope which immobilizes, for example, a vertically adjustable low temperature specimen holder during observation. The system provides balanced braking forces which can be easily removed and re-established with minimal disturbance to arbor location.

Analytic model for the dynamic Z-pinch

DOE Office of Scientific and Technical Information (OSTI.GOV)

Piriz, A. R., E-mail: roberto.piriz@uclm.es; Sun, Y. B.; Tahir, N. A.

2015-06-15

A model is presented for describing the cylindrical implosion of a shock wave driven by an accelerated piston. It is based in the identification of the acceleration of the shocked mass with the acceleration of the piston. The model yields the separate paths of the piston and the shock. In addition, by considering that the shocked region evolves isentropically, the approximate profiles of all the magnitudes in the shocked region are obtained. The application to the dynamic Z-pinch is presented and the results are compared with the well known snowplow and slug models which are also derived as limiting casesmore » of the present model. The snowplow model is seen to yield a trajectory in between those of the shock and the piston. Instead, the neglect of the inertial effects in the slug model is seen to produce a too fast implosion, and the pressure uniformity is shown to lead to an unphysical instantaneous piston stopping when the shock arrives to the axis.« less

Friction of Aviation Engines

NASA Technical Reports Server (NTRS)

Sparrow, S W; Thorne, M A

1928-01-01

The first portion of this report discusses measurements of friction made in the altitude laboratory of the Bureau of Standards between 1920 and 1926 under research authorization of the National Advisory Committee for Aeronautics. These are discussed with reference to the influence of speed, barometric pressure, jacket-water temperature, and throttle opening upon the friction of aviation engines. The second section of the report deals with measurements of the friction of a group of pistons differing from each other in a single respect, such as length, clearance, area of thrust face, location of thrust face, etc. Results obtained with each type of piston are discussed and attention is directed particularly to the fact that the friction chargeable to piston rings depends upon piston design as well as upon ring design. This is attributed to the effect of the rings upon the thickness and distribution of the oil film which in turn affects the friction of the piston to an extent which depends upon its design.

Experimental Evaluation of the Free Piston Engine - Linear Alternator (FPLA)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leick, Michael T.; Moses, Ronald W.

2015-03-01

This report describes the experimental evaluation of a prototype free piston engine - linear alternator (FPLA) system developed at Sandia National Laboratories. The opposed piston design wa developed to investigate its potential for use in hybrid electric vehicles (HEVs). The system is mechanically simple with two - stroke uniflow scavenging for gas exchange and timed port fuel injection for fuel delivery, i.e. no complex valving. Electrical power is extracted from piston motion through linear alternators wh ich also provide a means for passive piston synchronization through electromagnetic coupling. In an HEV application, this electrical power would be used to chargemore » the batteries. The engine - alternator system was designed, assembled and operated over a 2 - year period at Sandia National Laboratories in Livermore, CA. This report primarily contains a description of the as - built system, modifications to the system to enable better performance, and experimental results from start - up, motoring, and hydrogen combus tion tests.« less

On the generation of magnetized collisionless shocks in the large plasma device

NASA Astrophysics Data System (ADS)

Schaeffer, D. B.; Winske, D.; Larson, D. J.; Cowee, M. M.; Constantin, C. G.; Bondarenko, A. S.; Clark, S. E.; Niemann, C.

2017-04-01

Collisionless shocks are common phenomena in space and astrophysical systems, and in many cases, the shocks can be modeled as the result of the expansion of a magnetic piston though a magnetized ambient plasma. Only recently, however, have laser facilities and diagnostic capabilities evolved sufficiently to allow the detailed study in the laboratory of the microphysics of piston-driven shocks. We review experiments on collisionless shocks driven by a laser-produced magnetic piston undertaken with the Phoenix laser laboratory and the Large Plasma Device at the University of California, Los Angeles. The experiments span a large parameter space in laser energy, background magnetic field, and ambient plasma properties that allow us to probe the physics of piston-ambient energy coupling, the launching of magnetosonic solitons, and the formation of subcritical shocks. The results indicate that piston-driven magnetized collisionless shocks in the laboratory can be characterized with a small set of dimensionless formation parameters that place the formation process in an organized and predictive framework.

The use of CO(2) laser in revision stapes surgery: experimental studies on heat transmission to the vestibule.

PubMed

Szymański, Marcin; Morshed, Kamal; Mills, Robert P

2007-01-01

The aim of the study was to assess the effect of CO(2) laser on stapes prostheses and measure the heat transmission to the vestibule in experiment model. CO(2) laser was applied on two types of prostheses with power settings (2 and 6W; 0.05 s). Transmission of heat to the 'vestibule' was measured using type K thermocouple and DC-80 data logger during application of the laser on prostheses using a training model of temporal bone. Application of the laser on stainless steel prosthesis did not have any effect on the structure of the prosthesis. The use of the laser on the fluoroplastic-wire piston caused melting and produced holes in the piston. Greater temperature rises occurred with stainless steel than with the fluoroplastic-wire piston. Application of CO(2) laser on stainless steel pistons with 6W can produce inner ear trauma. The use of the laser on fluoroplastic-wire piston is not likely to irritate the inner ear.

Braking system

DOEpatents

Norgren, D.U.

1982-09-23

A balanced braking system comprising a plurality of braking assemblies located about a member to be braked. Each of the braking assemblies consists of a spring biased piston of a first material fitted into a body of a different material which has a greater contraction upon cooling than the piston material. The piston is provided with a recessed head portion over which is positioned a diaphragm and forming a space therebetween to which is connected a pressurized fluid supply. The diaphragm is controlled by the fluid in the space to contact or withdraw from the member to be braked. A cooling means causes the body within which the piston is fitted to contract more than the piston, producing a tight shrink fit therebetween. The braking system is particularly applicable for selectively braking an arbor of an electron microscope which immobilizes, for example, a vertically adjustable low temperature specimen holder during observation. The system provides balanced braking forces which can be easily removed and re-established with minimal disturbance to arbor location.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaeffer, D. B.; Winske, D.; Larson, D. J.

Collisionless shocks are common phenomena in space and astrophysical systems, and in many cases, the shocks can be modeled as the result of the expansion of a magnetic piston though a magnetized ambient plasma. Only recently, however, have laser facilities and diagnostic capabilities evolved sufficiently to allow the detailed study in the laboratory of the microphysics of piston-driven shocks. We review experiments on collisionless shocks driven by a laser-produced magnetic piston undertaken with the Phoenix laser laboratory and the Large Plasma Device at the University of California, Los Angeles. The experiments span a large parameter space in laser energy, backgroundmore » magnetic field, and ambient plasma properties that allow us to probe the physics of piston-ambient energy coupling, the launching of magnetosonic solitons, and the formation of subcritical shocks. Here, the results indicate that piston-driven magnetized collisionless shocks in the laboratory can be characterized with a small set of dimensionless formation parameters that place the formation process in an organized and predictive framework.« less

On the generation of magnetized collisionless shocks in the large plasma device

DOE PAGES

Schaeffer, D. B.; Winske, D.; Larson, D. J.; ...

2017-03-22

Collisionless shocks are common phenomena in space and astrophysical systems, and in many cases, the shocks can be modeled as the result of the expansion of a magnetic piston though a magnetized ambient plasma. Only recently, however, have laser facilities and diagnostic capabilities evolved sufficiently to allow the detailed study in the laboratory of the microphysics of piston-driven shocks. We review experiments on collisionless shocks driven by a laser-produced magnetic piston undertaken with the Phoenix laser laboratory and the Large Plasma Device at the University of California, Los Angeles. The experiments span a large parameter space in laser energy, backgroundmore » magnetic field, and ambient plasma properties that allow us to probe the physics of piston-ambient energy coupling, the launching of magnetosonic solitons, and the formation of subcritical shocks. Here, the results indicate that piston-driven magnetized collisionless shocks in the laboratory can be characterized with a small set of dimensionless formation parameters that place the formation process in an organized and predictive framework.« less

Passive blast pressure sensor

DOEpatents

King, Michael J.; Sanchez, Roberto J.; Moss, William C.

2013-03-19

A passive blast pressure sensor for detecting blast overpressures of at least a predetermined minimum threshold pressure. The blast pressure sensor includes a piston-cylinder arrangement with one end of the piston having a detection surface exposed to a blast event monitored medium through one end of the cylinder and the other end of the piston having a striker surface positioned to impact a contact stress sensitive film that is positioned against a strike surface of a rigid body, such as a backing plate. The contact stress sensitive film is of a type which changes color in response to at least a predetermined minimum contact stress which is defined as a product of the predetermined minimum threshold pressure and an amplification factor of the piston. In this manner, a color change in the film arising from impact of the piston accelerated by a blast event provides visual indication that a blast overpressure encountered from the blast event was not less than the predetermined minimum threshold pressure.

Development of EPA aircraft piston engine emission standards. [for air quality

NASA Technical Reports Server (NTRS)

Houtman, W.

1976-01-01

Piston engine light aircraft are significant sources of carbon monoxide in the vicinity of high activity general aviation airports. Substantial reductions in carbon monoxide were achieved by fuel mixture leaning using improved fuel management systems. The air quality impact of the hydrocarbon and oxides of nitrogen emissions from piston engine light aircraft were insufficient to justify the design constraints being confronted in present control system developments.

Pull rod assembly

DOEpatents

Cioletti, O.C.

1988-04-21

A pull rod assembly comprising a pull rod having three peripheral grooves, a piston device including an adaptor ring and a seal ring, said piston device being mounted on the pull rod by a split ring retainer situated in one groove and extending into an interior groove in the adaptor and a resilient split ring retained in another groove and positioned to engage the piston device and to retain the seal on its adaptor.

Design and Fabrication of Micro-Electro-Mechanical Structures for Tunable Micro-Optical Devices

DTIC Science & Technology

2002-03-01

purposes. Figure 2.6 shows the resulting Voltage vs. displacement curve for a 150 µm × 150 µm piston micromirror with four 150 µm flexures, and a 2 µm...2-6 2.3.2 Piston Micromirrors . . . . . . . . . . . . . . . . . . 2-7 2.4 VCSEL Design...Schematic view of basic electrostatic piston micromirror [4]. . . . . 2-7 2.5. Deflection of a flexure beam with a single fixed end [22]. . . . . . . 2

Structural design of Stirling engine with free pistons

NASA Astrophysics Data System (ADS)

Matusov, Jozef; Gavlas, Stanislav; Malcho, Milan

2014-08-01

Stirling engine is a device that converts thermal energy to mechanical work, which is mostly used to drive a generator of electricity. Advantage of Stirling engine is that it works with closed-cycle, where working medium is regularly cooled and heated, which acts on the working piston. This engine can be made in three modifications - alpha, beta, gamma. This paper discusses the design of the gamma Stirling engine with free pistons.

Accumulation rates of Th-230, Pa-231, and some transition metals on the Bermuda Rise

USGS Publications Warehouse

Bacon, M.P.; Rosholt, J.N.

1982-01-01

Measurements of 238U, 234U, 230Th, 232Th, 231Pa, Mn, Fe, Co, Ni, Cu, and Zn were made on 23 samples from core GPC-5, a 29-m giant piston core from a water depth of 4583 m on the northeastern Bermuda Rise (33??41.2???N, 57??36.9???W). This area is characterized by rapid deposition of sediment transported by abyssal currents. Unsupported 230Th and 231Pa are present throughout the core but, because of large variations in the sedimentation rate, show marked departures from exponential decay with depth. The trend with depth of the 231Paex 230Thex ratio is consistent with the average accumulation rate of 36 cm/1000 y reported earlier on the basis of radiocarbon dating and CaCO3 stratigraphy. When expressed on a carbonate-free basis, concentrations of Mn, Co, Ni, Cu, Zn, 230Thex, and 231Paex all show cyclic variations positively correlated with those of CaCO3. The correlations can be explained by a model in which all of these constituents, including CaCO3, are supplied to the sediments from the water column at a constant rate. Concentration variations are controlled mainly by varying inputs of terrigenous detritus, with low inputs occurring during interglacials and high inputs during glacials. Relationships between the metal and 230Thex concentrations permit estimates of the rates at which the metals are removed to the sediment by scavenging from the water column. The results, in ??g/cm2-1000 y, are: 4300 ?? 1100 for Mn, 46 ?? 16 for Ni and 76 ?? 26 for Cu. These rates are somewhat larger than ocean-wide averages estimated by other methods, and the absolute rate of 230Th accumulation in GPC-5 averages about nine times higher than production in the overlying water column. This part of the Bermuda Rise and similar bottom-current deposits may act as important accumulators of elements scavenged from seawater. ?? 1982.

Past collapse and late Holocene reestablishment of the Petermann Ice Tongue, Northwest Greenland

NASA Astrophysics Data System (ADS)

Reilly, B. T.; Stoner, J. S.; Mix, A. C.; Jakobsson, M.; Jennings, A. E.; Walczak, M.; Dyke, L. M.

2017-12-01

Petermann Glacier, Northwest Greenland, has been a stable outlet glacier of the Greenland Ice Sheet on historical timescales. Yet, anomalous calving events in 2010 and 2012 and oceanographic studies over the last decade indicate that Petermann Glacier and its ice tongue are especially sensitive to ice-ocean interactions, leading many to speculate on its future stability. To place these observations in the context of a longer timeframe and better understand the sensitivity of Petermann Glacier to future climate change, a 2015 international and interdisciplinary expedition of the Icebreaker Oden collected a suite of sediment cores from Petermann Fjord, spanning the mid to late Holocene and forming a transect from beneath the modern ice tongue to the mouth of the fjord (25 - 80 km from the modern grounding line). We characterize the stratigraphy ( 5.5 - 6.5 m at piston core sites) using a combination of X-ray fluorescence (XRF) scanning geochemistry, computed tomography (CT) scanning, and particle-size specific magnetic measurements on these cores and nearby terrestrial samples. Age-depth modeling, based on radiocarbon dated benthic foraminifera, is in progress with reservoir age corrections assessed using paleomagnetic comparisons to regional and global records. We observe changes in the composition and spatial pattern of ice rafted debris (IRD) and sediment fabric that reveal a dynamic history. Following early Holocene deglaciation of the region, a paleo-ice tongue broke up and an extended period of seasonally open marine conditions ensued through the middle Holocene. This ice-tongue collapse was followed by a large increase in the relative abundance of Petermann sourced IRD of non-local granitic composition. This granitic IRD component steadily declined through the middle Holocene, reaching negligible contributions when the ice tongue was reestablished in the late Holocene. Regional paleoenvironmental studies suggest warmer oceanographic and atmospheric conditions around Northwest Greenland in the middle Holocene, offering an opportunity to study the sensitivity of one of Greenland's major outlet glaciers to environmental forcing.

Piston-assisted proton pumping in Complex I of mitochondria membranes

NASA Astrophysics Data System (ADS)

Mourokh, Lev; Filonenko, Ilan

2014-03-01

Proton-pumping mechanism of Complex I remains mysterious because its electron and proton paths are well separated and the direct Coulomb interaction seems to be negligible. The structure of this enzyme was resolved very recently and its functionality was connected the shift of the helix HL. We model the helix as a piston oscillating between the protons and electrons. We assume that positive charges are accumulated near the edges of the helix. In the oxidized state, the piston is attracted to electrons, so its distance to the proton sites increases, the energy of these sites decreases and the sites can be populated. When electrons proceed to the drain, elastic forces return the piston to the original position and the energies of populated proton sites increase, so the protons can be transferred to the positive site of the membrane. In this work, we explore a simplified model when the interaction of the piston with electrons is replaced by a periodic force. We derive quantum Heisenberg equations for the proton operators and solve them jointly with the Langevin equation for the piston position. We show that the proton pumping is possible in such structure with parameters closely resembling the real system. We also address the feasibility of using such mechanism in nanoelectronics.

Testing and Calibration of Phase Plates for JWST Optical Simulator

NASA Technical Reports Server (NTRS)

Gong, Qian; Chu, Jenny; Tournois, Severine; Eichhorn, William; Kubalak, David

2011-01-01

Three phase plates were designed to simulate the JWST segmented primary mirror wavefront at three on-orbit alignment stages: coarse phasing, intermediate phasing, and fine phasing. The purpose is to verify JWST's on-orbit wavefront sensing capability. Amongst the three stages, coarse alignment is defined to have piston error between adjacent segments being 30 m to 300 m, intermediate being 0.4 m to 10 m, and fine is below 0.4 m. The phase plates were made of fused silica, and were assembled in JWST Optical Simulator (OSIM). The piston difference was realized by the thickness difference of two adjacent segments. The two important parameters to phase plates are piston and wavefront errors. Dispersed Fringe Sensor (DFS) method was used for initial coarse piston evaluation, which is the emphasis of this paper. Point Diffraction Interferometer (PDI) is used for fine piston and wavefront error. In order to remove piston's 2 pi uncertainty with PDI, three laser wavelengths, 640nm, 660nm, and 780nm, are used for the measurement. The DHS test setup, analysis algorithm and results are presented. The phase plate design concept and its application (i.e. verifying the JWST on-orbit alignment algorithm) are described. The layout of JWST OSIM and the function of phase plates in OSIM are also addressed briefly.

Overview of the 1986 free-piston Stirling activities at NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Alger, Donald L.

1986-01-01

An overview of the NASA Lewis Research Center's free-piston Stirling engine research is presented, including efforts to improve and advance its design for use in specific space power applications. These efforts are a part of the SP-100 program being conducted to support the Department of Defense (DOD), Department of Energy (DOE) and NASA. Such efforts include: (1) the testing and improvement of 25 kWe Stirling Space Power Demonstrator Engine (SPDE); (2) the preliminary design of 25 kWe single-cylinder Experimental stirling Space Engine (ESSE); and, (3) a study to determine the feasibility of scaling a single-cylinder free-piston Stirling engine/linear alternator to 150 kWe. Other NASA Lewis free-piston Stirling engine activities will be described, directed toward the advancement of general free-piston Stirling engine technology and its application in specific terrestrial applications. One such effort, supported by DOE/Oak Ridge National Laboratory (DRNL), is the development of a free-piston Stirling engine which produces hydraulic power. Finally, a terrestrial solar application involving a conceptual design of a 25 kWe Solar Advanced Stirling Conversion System (ASCS) capable of delivering power to an electric utility grid will be discussed. The latter work is supported by DOE/Sandia National Laboratory (SNLA).

Diamond-anvil high-pressure cell with improved x-ray collimation system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schiferl, D.; Olinger, B.W.; Livingston, R.W.

1986-07-22

This patent describes a diamond-anvil high-pressure cell having a tubular piston and a cylinder in which the piston is slidable to effect compression of a pair of opposed diamonds located between the piston and the cylinder. The piston includes a central bore opening on one end, an adjustable X-ray collimation system comprising a tubular insert engageable in the bore of the piston, the insert including a central bore and having first and second ends, with the first end of the insert being closest to the opposed diamonds and the second end of the insert extending out of the open endmore » of the piston, a collimator insertable in the bore of the tubular insert. The collimator has a central bore and having first and second ends corresponding respectively with the first and second ends of the insert, elastomeric pivot means mounted in the bore of the insert at the first end of the insert for flexibly retaining the first end of the collimator while allowing the collimator to pivot within the pivot means, and adjustable locking means located at the second end of the insert for adjusting and securing the second end of the collimator so as to be in alignment with the opposed diamonds.« less

Investigation on the electromagnetic centring technique in compressor with labyrinth seal structure

NASA Astrophysics Data System (ADS)

Zhang, W.; Feng, C.; Cheng, J.; Feng, Q.; Wu, W.

2017-08-01

At present, the piston of compressors with labyrinth seal structure generally runs eccentrically, which causes uneven radial clearance, serious leakages and lower volumetric efficiency. This has become an urgent problem in the development of labyrinth compressors. In this study, electromagnetic levitation technology was introduced to achieve concentric centering between the piston and cylinder, and the conventional cantilever structure for the piston centering was replaced by a simple support structure using the through-piston rod. Furthermore, the simulation model of the electromagnetic centering system was established and the experimental prototype was built. The mathematical simulation model was verified by comparing simulated and tested results. Then, the centering effect of the system was assessed and the variation of the leakage in the compressor was studied by models using dynamic mesh technology. The results showed that the radial clearance between piston and cylinder can be maintained in the range of -0.3 mm to 0.3 mm through the electromagnetic centering control. In addition, the inner leakage of the compressor was quite appreciable without the electromagnetic control. However, it was reduced by 1.8 times with the introduction of the electromagnetic control. Thus, it can be concluded that the precise centering between the piston and the cylinder can be achieved by the introduction of the electromagnetic centering technique.

P-REx: The Piston Reconstruction Experiment for infrared interferometry

NASA Astrophysics Data System (ADS)

Widmann, Felix; Pott, Jörg-Uwe; Velasco, Sergio

2018-03-01

For sensitive infrared interferometry, it is crucial to control the differential piston evolution between the used telescopes. This is classically done by the use of a fringe tracker. In this work, we develop a new method to reconstruct the temporal piston variation from the atmosphere, by using real-time data from adaptive optics (AO) wavefront sensing: the Piston Reconstruction Experiment (P-REx). In order to understand the principle performance of the system in a realistic multilayer atmosphere, it is first extensively tested in simulations. The gained insights are then used to apply P-REx to real data, in order to demonstrate the benefit of using P-REx as an auxiliary system in a real interferometer. All tests show positive results, which encourages further research and eventually a real implementation. Especially, the tests on on-sky data showed that the atmosphere is, under decent observing conditions, sufficiently well structured and stable, in order to apply P-REx. It was possible to conveniently reconstruct the piston evolution in two-thirds of the data sets from good observing conditions (r0 ˜ 30 cm). The main conclusion is that applying the piston reconstruction in a real system would reduce the piston variation from around 10 μm down to 1-2 μm over time-scales of up to two seconds. This suggests an application for mid-infrared interferometry, for example for MATISSE at the very large telescope interferometer or the large binocular telescope interferometer. P-REx therefore provides the possibility to improve interferometric measurements without the need for more complex AO systems than already in regular use at 8-m-class telescopes.

Shallowly driven fluctuations in lava lake outgassing (gas pistoning), Kīlauea Volcano

NASA Astrophysics Data System (ADS)

Patrick, Matthew R.; Orr, Tim; Sutton, A. J.; Lev, Einat; Thelen, Wes; Fee, David

2016-01-01

Lava lakes provide ideal venues for directly observing and understanding the nature of outgassing in basaltic magmatic systems. Kīlauea Volcano's summit lava lake has persisted for several years, during which seismic and infrasonic tremor amplitudes have exhibited episodic behavior associated with a rise and fall of the lava surface (;gas pistoning;). Since 2010, the outgassing regime of the lake has been tied to the presence or absence of gas pistoning. During normal behavior (no gas pistoning), the lake is in a ;spattering; regime, consisting of higher tremor amplitudes and gas emissions. In comparison, gas piston events are associated with an abrupt rise in lava level (up to 20 m), during which the lake enters a ;non-spattering; regime with greatly decreased tremor and gas emissions. We study this episodic behavior using long-term multidisciplinary monitoring of the lake, including seismicity, infrasound, gas emission and geochemistry, and time-lapse camera observations. The non-spattering regime (i.e. rise phase of a gas piston cycle) reflects gas bubbles accumulating near the top of the lake, perhaps as a shallow foam, while spattering regimes represent more efficient decoupling of gas from the lake. We speculate that the gas pistoning might be controlled by time-varying porosity and/or permeability in the upper portions of the lava lake, which may modulate foam formation and collapse. Competing models for gas pistoning, such as deeply sourced gas slugs, or dynamic pressure balances, are not consistent with our observations. Unlike other lava lakes which have cyclic behavior that is thought to be controlled by deeply sourced processes, external to the lake itself, we show an example of lava lake fluctuations driven by cycles of activity at shallow depth and close to the lake's surface. These observations highlight the complex and unsteady nature of outgassing from basaltic magmatic systems.

Long-range effect of ion implantation of Raex and Hardox steels

NASA Astrophysics Data System (ADS)

Budzyński, P.; Kamiński, M.; Droździel, A.; Wiertel, M.

2016-09-01

Ion implantation involves introduction of ionized atoms of any element (nitrogen) to metals thanks to the high kinetic energy that they acquired in the electric field. The distribution of nitrogen ions implanted at E = 65 keV energy and D = 1.1017 N+ /cm2 fluence in the steel sample and vacancies produced by them was calculated using the SRIM program. This result was confirmed by RBS measurements. The initial maximum range of the implanted nitrogen ions is ∼⃒0.17 μm. This value is relatively small compared to the influence of nitriding on the thickness surface layer of modified steel piston rings. Measurements of the friction coefficient during the pin-on-disc tribological test were performed under dry friction conditions. The friction coefficient of the implanted sample increased to values characteristic of an unimplanted sample after ca. 1500 measurement cycles. The depth of wear trace is ca. 2.4 μm. This implies that the thickness of the layer modified by the implantation process is ∼⃒2.4 μm and exceeds the initial range of the implanted ions by an order of magnitude. This effect, referred to as a long-range implantation effect, is caused by migration of vacancies and nitrogen atoms into the sample. This phenomenon makes ion implantation a legitimate process of modification of the surface layer in order to enhance the tribological properties of critical components of internal combustion engines such as steel piston rings.

Paleocurrent analysis and physical properties of deep-sea mud cores collected from NW Pacific and Northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Suzuki, T.; Kawamura, K.; Ogawa, Y.; Flemings, P. B.; Behrmann, J. H.; John, C. M.; Hirano, N.; Abe, N.

2005-12-01

We collected three m-long piston cores of mud during the Kairei cruise (KR04-08 and KR05-10) of Japan Marine Science and Technology Center in 2004 and 2005 from the NW Pacific between Honshu and Shatsky Rise; aside the Fukahori Knoll and Yukawa Knoll. Another set of mud cores, 234.5 m long, was collected during the JOIDES Resolution cruise (IODP Exp308, site U1322) in 2005 from the Ursa Basin located at the eastern levee of the Mississippi Canyon, northeastern Gulf of Mexico of about 1000 m depth. Our study purpose is to know the flow direction by mud particle arrangement by thin section and scanning electron microscope (SEM) and anisotropy of magnetic susceptibility (AMS) data. The data from the NW Pacific indicate weak preferred orientation from SW to NE, suggesting weak bottom current. This is supported by erosional moat to NE direction around the Fukahori Knoll. In the Gulf of Mexico we can know the flow directions of river plumes, turbidity currents, etc., and we can know whether the flows come from the main entry point in the basin or they are derived from the others of the basin. The other basic features of the core sediments are lithology, sedimentary structures, and porosity, together with paleocurrent analysis.

Periodicity of the density wake past a vortex ring in a stratified liquid

NASA Astrophysics Data System (ADS)

Prokhorov, V.

2009-04-01

Spatial coherent structure of the density wake past a vortex ring moving horizontally in viscid stratified liquid is experimentally revealed. It follows from analysis that repetition period of the structure is determined by rotation radial frequency (or mean vorticity) of the vortex core and toward speed of the vortex ring. The wake formation of the ring is considered in respect to vorticity shedding which produces velocity disturbances in ambient medium. In case of stratified liquid velocity fluctuations, in their turn, cause density field distortion. This process is superimposed by vortex core oscillations, and, in result, vorticity shedding will be not monotonous but modulated at some frequency. So, the density wake is periodically structured, and the spatial period is defined by intrinsic frequency of the core and forward speed of the ring. To support analysis, experiments were conducted in which vortex rings excited by spring-piston generator were observed with high-sensitive Schlieren instrument and computer-controlled camera. Experimental tank was filled with salt-stratified water of constant buoyancy period, vortex ring velocities range from 3 to 16 cm/s. Spatial period is derived from schlieren image using two independent methods, both 2D spectral analysis and geometry calculations of the vortex core. Spatial periods and vortex intrinsic frequencies calculated by both algorithms are in good agreement; they vary in power lows depending on vortex speed

Revised tuning of Ocean Drilling Program Site 964 and KC01B (Mediterranean) and implications for the δ18O, tephra, calcareous nannofossil, and geomagnetic reversal chronologies of the past 1.1 Myr

NASA Astrophysics Data System (ADS)

Lourens, Lucas J.

2004-09-01

High-resolution color reflectance records of KC01 and KC01B (Calabrian Ridge, Ionian Sea) are presented and compared with a modified spliced high-resolution color reflectance record of Ocean Drilling Program (ODP) Site 964. This comparison revealed that KC01B is characterized by intensive deformation between ~27 and 28.5 m piston depth and that some sapropels are tectonically reduced in thickness. Moreover, the piston coring has caused considerable stretching in the top of KC01 and KC01B. Using a new splice of ODP Site 964 as guide, previous astronomical tuned timescales of KC01B and ODP Site 964 were evaluated. This evaluation resulted in a new sapropel-based astronomical timescale for the last 1.1 Myr. The new timescale implies a much more uniform change in sedimentation rate for the Ionian Sea cores. Two prominent excursions to lighter values in the δ18O record of the planktonic foraminiferal species Globigerinoides ruber occur during marine isotopic stages 12 and 16 applying the new timescale. These shifts correspond with maxima in obliquity and are punctuated by minima in the precession cycle. They are absent in global ice volume records and are interpreted as reflecting a (summer) low-salinity surface water lens that floats on top of extremely saline intermediate and deep waters at times of the very low sea levels during these glacial periods. All biostratigraphic and magnetostratigraphic events found in KC01B and ODP Site 964 were re-dated according to the new timescale, and the ages of 33 tephra layers were reviewed. The new ages for the Calabrian Ridge 2 and 3 magnetic events in the Brunhes are concordant with minima in the global Sint800 composite record, derived from worldwide deep-sea records of relative paleointensity and have been attributed to the Big Lost and La Palma excursions, respectively.

High pressure rotary piston coal feeder for coal gasification applications

DOEpatents

Gencsoy, Hasan T.

1977-05-24

The subject development is directed to an apparatus for feeding pulverized coal into a coal gasifier operating at relatively high pressures and elevated temperatures. This apparatus is a rotary piston feeder which comprises a circular casing having a coal loading opening therein diametrically opposed from a coal discharge and contains a rotatable discoid rotor having a cylinder in which a reciprocateable piston is disposed. The reciprocation of the piston within the cylinder is provided by a stationary conjugate cam arrangement whereby the pulverized coal from a coal hopper at atmospheric pressure can be introduced into the cylinder cavity and then discharged therefrom into the high-pressure gasifier without the loss of high pressure gases from within the latter.

Reduced energy and volume air pump for a seat cushion

DOEpatents

Vaughn, M.R.; Constantineau, E.J.; Groves, G.E.

1997-08-19

An efficient pump system is described for transferring air between sets of bladders in a cushion. The pump system utilizes a reversible piston within a cylinder in conjunction with an equalizing valve in the piston which opens when the piston reaches the end of travel in one direction. The weight of a seated user then forces air back across the piston from an inflated bladder to the previously deflated bladder until the pressure is equalized. In this fashion the work done by the pump is cut in half. The inflation and deflation of the different bladders is controlled to vary the pressure on the several pressure points of a seated user. A principal application is for wheel chair use to prevent pressure ulcers. 12 figs.

The performance simulation of single cylinder electric power confined piston engine

NASA Astrophysics Data System (ADS)

Gou, Yanan

2017-04-01

A new type of power plant. i.e, Electric Power Confined Piston Engine, is invented by combining the free piston engine and the crank connecting rod mechanism of the traditional internal combustion engine. Directly using the reciprocating movement of the piston, this new engine converts the heat energy produced by fuel to electrical energy and output it. The paper expounds the working mechanism of ECPE and establishes the kinematics and dynamics equations. Furthermore, by using the analytic method, the ECPE electromagnetic force is solved at load cases. Finally, in the simulation environment of MARLAB, the universal characteristic curve is obtained in the condition of rotational speed n between 1000 r/min and 2400 r/min, throttle opening α between 30% and 100%.

Contribution of developing advanced engineering methods in interdisciplinary studying the piston rings from 1.6 spark ignited Ford engine at Technical University of Cluj-Napoca

NASA Astrophysics Data System (ADS)

-Aurel Cherecheş, Ioan; -Ioana Borzan, Adela; -Laurean Băldean, Doru

2017-10-01

Study of construction and wearing process in the case of piston-rings and other significant components from internal combustion engines leads at any time to creative and useful optimizing ideas, both in designing and manufacturing phases. Main objective of the present paper is to realize an interdisciplinary research using advanced methods in piston-rings evaluation of a common vehicle on the streets which is Ford Focus FYDD. Specific objectives are a theoretical study of the idea for advanced analysis method in piston-rings evaluation and an applied research developed in at Technical University from Cluj-Napoca with the motor vehicle caught in the repairing process.

Reduced energy and volume air pump for a seat cushion

DOEpatents

Vaughn, Mark R.; Constantineau, Edward J.; Groves, Gordon E.

1997-01-01

An efficient pump system for transferring air between sets of bladders in a cushion. The pump system utilizes a reversible piston within a cylinder in conjunction with an equalizing valve in the piston which opens when the piston reaches the end of travel in one direction. The weight of a seated user then forces air back across the piston from an inflated bladder to the previously deflated bladder until the pressure is equalized. In this fashion the work done by the pump is cut in half. The inflation and deflation of the different bladders is controlled to vary the pressure on the several pressure points of a seated user. A principal application is for wheel chair use to prevent pressure ulcers.

Test Method Designed to Evaluate Cylinder Liner-Piston Ring Coatings for Advanced Heat Engines

NASA Technical Reports Server (NTRS)

Radil, Kevin C.

1997-01-01

Research on advanced heat engine concepts, such as the low-heat-rejection engine, have shown the potential for increased thermal efficiency, reduced emissions, lighter weight, simpler design, and longer life in comparison to current diesel engine designs. A major obstacle in the development of a functional advanced heat engine is overcoming the problems caused by the high combustion temperatures at the piston ring/cylinder liner interface, specifically at top ring reversal (TRR). Therefore, advanced cylinder liner and piston ring materials are needed that can survive under these extreme conditions. To address this need, researchers at the NASA Lewis Research Center have designed a tribological test method to help evaluate candidate piston ring and cylinder liner materials for advanced diesel engines.

Ballistic parameters of .177 (4.5 mm) caliber plastic-sleeved composite projectiles compared to conventional lead pellets.

PubMed

Frank, Matthias; Schönekeß, Holger; Jäger, Frank; Herbst, Jörg; Ekkernkamp, Axel; Nguyen, Thanh Tien; Bockholdt, Britta

2013-11-01

The capability of conventional air gun lead pellets (diabolo pellets) to cause severe injuries or fatalities even at low kinetic energy levels is well documented in medical literature. Modern composite hunting pellets, usually a metal core (made of steel, lead, zinc, or a zinc and aluminum alloy) encased in a plastic sleeve, are of special forensic and traumatological interest. These projectiles are advertised by the manufacturers to discharge at higher velocities than conventional air gun pellets, thus generating very high tissue-penetrating capabilities. Lack of experimental data on these uncommon air gun projectiles induced this work. Ballistic parameters of 12 different caliber .177 (4.5 mm) composite pellets, discharged from two spring-piston air guns (Weihrauch HW 35, Webley CUB) and three pneumatic air guns (Walther LGR, Walther LG400, Walther LP300), were investigated using a ballistic speed measurement system and compared to a conventional diabolo pellet (RWS Meisterkugel) as reference projectile. Although overall results were inconsistent, for some projectile-weapon combinations (particularly spring-piston air guns), a significant change of the kinetic energy (-53 up to +48 %) to the reference projectile was observed. The data provided in this work may serve as a basis for forensic investigation as well as traumatological diagnosis and treatment of injuries caused by these uncommon projectiles.

Design of an interferometric system for piston measurements in segmented primary mirrors

NASA Astrophysics Data System (ADS)

Arasa, Josep; Laguarta, Ferran; Pizarro, Carlos; Tomas, Nuria; Pinto, Agusti

2000-10-01

Recently, telescopes with segmented primary mirrors are becoming increasingly popular due to their ability of achieving large apertures without the inconveniences caused by the fabrication and handling of monolithic surfaces with 8m (or over) in diameter. The difference in position of each pair of adjacent segments along the local normal of their interface (called piston hereafter), however, needs to be precisely measured in order to provide a diffraction- limited image. If a system yielding the nanometric accuracy required in piston measurements worked in daylight hours, the resultant saving in observation time would be an important advance on a majority of the state-of-the-art piston measurement systems. An interferometric piston measurement instrument accomplishing such objectives has been designed starting from the usual Michelson configuration at the CD6 (Terrassa, Spain), and its final test has been carried out in the test workbench of the Instituto de Astrofisica de Canarias (IAC, Canary Islands, Spain). Its optical layout relies on projecting the reference arm of the interferometer onto one of the segments of the pair considered, along the direction of the local normal to the surface while the measurement arm is projected onto the interface which divides the pair of segments considered. The field of view and its illumination are calculated to be equivalent in both segments. The lateral shift of the fringes in both interferograms determines the piston error present. A combination of monochromatic and white light is used, in order to remove the (lambda) /2 phase ambiguities present in piston measurements without losing the required resolution in the measurement. In this paper, the optical design of this interferometric piston measurement instrument will be presented. The particular configuration used in the interferometer, the implementation of an imaging system allowing to see both the interface of the segments and the interference fringes, the effect of the extension of the source and the use of both monochromatic and whit light will be discussed. A detailed study of the wavefront errors embedded in the wavefront at different stages of the interferometer is performed. The analysis shows the validity of the design of the instrument, and some experimental results obtained at the test workbench are provided to demonstrate the ability of the instrument to perform nanometric piston measurements under daylight conditions.

Quasi-static and dynamic motions of the columellar footplate in ostrich (Struthio camelus) measured ex vivo.

PubMed

Muyshondt, Pieter G G; Claes, Raf; Aerts, Peter; Dirckx, Joris J J

2018-01-01

The nature of the movement of the columellar footplate (CFP) in birds is still a matter of ongoing debate. Some sources claim that rocking motion is dominant, while others propose a largely piston-like motion. In this study, motions of the CFP are experimentally investigated in the ostrich using a post-mortem approach. For quasi-static loads, micro-CT scans of ostrich heads were made under positive and negative middle-ear pressures of 1 kPa. For dynamic loads, laser Doppler vibrometry was used to measure the velocity on multiple locations of the CFP as a function of excitation frequency from 0.125 to 4 kHz, and digital stroboscopic holography was used to assess the 1D full-field out-of-plane displacement of the CFP at different excitation frequencies. To expose the CFP in the experiments, measurements were made from the medial side of the CFP after opening and draining the inner ear. To determine the influence of the inner-ear load on CFP motions, a finite element model was created of the intact ostrich middle ear with inner-ear load included. For quasi-static loads, the CFP performed largely piston-like motions under positive ME pressure, while under negative ME pressure the difference between piston and rocking motion was smaller. For dynamic loads, the CFP motion was almost completely piston-like for frequencies below 1 kHz. For higher frequencies, the motions became more complicated with an increase of the rocking components, although they never exceeded the piston component. When including the inner-ear load to the model, the rocking components started to increase relative to the piston component when compared to the result of the model with unloaded CFP, but only at high frequencies above 1 kHz. In this frequency range, the motion could no longer be identified as purely piston-like or rocking. As a conclusion, the current results suggest that CFP motion is predominantly piston-like below 1 kHz, while at higher frequencies the motion becomes too complicated to be described as purely piston-like or rocking. Copyright © 2017 Elsevier B.V. All rights reserved.

Pre-compression volume on flow ripple reduction of a piston pump

NASA Astrophysics Data System (ADS)

Xu, Bing; Song, Yuechao; Yang, Huayong

2013-11-01

Axial piston pump with pre-compression volume(PCV) has lower flow ripple in large scale of operating condition than the traditional one. However, there is lack of precise simulation model of the axial piston pump with PCV, so the parameters of PCV are difficult to be determined. A finite element simulation model for piston pump with PCV is built by considering the piston movement, the fluid characteristic(including fluid compressibility and viscosity) and the leakage flow rate. Then a test of the pump flow ripple called the secondary source method is implemented to validate the simulation model. Thirdly, by comparing results among the simulation results, test results and results from other publications at the same operating condition, the simulation model is validated and used in optimizing the axial piston pump with PCV. According to the pump flow ripples obtained by the simulation model with different PCV parameters, the flow ripple is the smallest when the PCV angle is 13°, the PCV volume is 1.3×10-4 m3 at such operating condition that the pump suction pressure is 2 MPa, the pump delivery pressure 15 MPa, the pump speed 1 000 r/min, the swash plate angle 13°. At the same time, the flow ripple can be reduced when the pump suction pressure is 2 MPa, the pump delivery pressure is 5 MPa,15 MPa, 22 MPa, pump speed is 400 r/min, 1 000 r/min, 1 500 r/min, the swash plate angle is 11°, 13°, 15° and 17°, respectively. The finite element simulation model proposed provides a method for optimizing the PCV structure and guiding for designing a quieter axial piston pump.

LOW-ENGINE-FRICTION TECHNOLOGY FOR ADVANCED NATURAL-GAS RECIPROCATING ENGINES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Victor Wong; Tian Tian; Luke Moughon

2005-09-30

This program aims at improving the efficiency of advanced natural-gas reciprocating engines (ANGRE) by reducing piston and piston ring assembly friction without major adverse effects on engine performance, such as increased oil consumption and wear. An iterative process of simulation, experimentation and analysis is being followed towards achieving the goal of demonstrating a complete optimized low-friction engine system. To date, a detailed set of piston and piston-ring dynamic and friction models have been developed and applied that illustrate the fundamental relationships between design parameters and friction losses. Low friction ring designs have already been recommended in a previous phase, withmore » full-scale engine validation partially completed. Current accomplishments include the addition of several additional power cylinder design areas to the overall system analysis. These include analyses of lubricant and cylinder surface finish and a parametric study of piston design. The Waukesha engine was found to be already well optimized in the areas of lubricant, surface skewness and honing cross-hatch angle, where friction reductions of 12% for lubricant, and 5% for surface characteristics, are projected. For the piston, a friction reduction of up to 50% may be possible by controlling waviness alone, while additional friction reductions are expected when other parameters are optimized. A total power cylinder friction reduction of 30-50% is expected, translating to an engine efficiency increase of two percentage points from its current baseline towards the goal of 50% efficiency. Key elements of the continuing work include further analysis and optimization of the engine piston design, in-engine testing of recommended lubricant and surface designs, design iteration and optimization of previously recommended technologies, and full-engine testing of a complete, optimized, low-friction power cylinder system.« less

A Linear Electromagnetic Piston Pump

NASA Astrophysics Data System (ADS)

Hogan, Paul H.

Advancements in mobile hydraulics for human-scale applications have increased demand for a compact hydraulic power supply. Conventional designs couple a rotating electric motor to a hydraulic pump, which increases the package volume and requires several energy conversions. This thesis investigates the use of a free piston as the moving element in a linear motor to eliminate multiple energy conversions and decrease the overall package volume. A coupled model used a quasi-static magnetic equivalent circuit to calculate the motor inductance and the electromagnetic force acting on the piston. The force was an input to a time domain model to evaluate the mechanical and pressure dynamics. The magnetic circuit model was validated with finite element analysis and an experimental prototype linear motor. The coupled model was optimized using a multi-objective genetic algorithm to explore the parameter space and maximize power density and efficiency. An experimental prototype linear pump coupled pistons to an off-the-shelf linear motor to validate the mechanical and pressure dynamics models. The magnetic circuit force calculation agreed within 3% of finite element analysis, and within 8% of experimental data from the unoptimized prototype linear motor. The optimized motor geometry also had good agreement with FEA; at zero piston displacement, the magnetic circuit calculates optimized motor force within 10% of FEA in less than 1/1000 the computational time. This makes it well suited to genetic optimization algorithms. The mechanical model agrees very well with the experimental piston pump position data when tuned for additional unmodeled mechanical friction. Optimized results suggest that an improvement of 400% of the state of the art power density is attainable with as high as 85% net efficiency. This demonstrates that a linear electromagnetic piston pump has potential to serve as a more compact and efficient supply of fluid power for the human scale.

Fast-acting valve actuator

DOEpatents

Cho, Nakwon

1980-01-01

A fast-acting valve actuator utilizes a spring driven pneumatically loaded piston to drive a valve gate. Rapid exhaust of pressurized gas from the pneumatically loaded side of the piston facilitates an extremely rapid piston stroke. A flexible selector diaphragm opens and closes an exhaust port in response to pressure differentials created by energizing and de-energizing a solenoid which controls the pneumatic input to the actuator as well as selectively providing a venting action to one side of the selector diaphragm.

Advanced diagnostic system for piston slap faults in IC engines, based on the non-stationary characteristics of the vibration signals

NASA Astrophysics Data System (ADS)

Chen, Jian; Randall, Robert Bond; Peeters, Bart

2016-06-01

Artificial Neural Networks (ANNs) have the potential to solve the problem of automated diagnostics of piston slap faults, but the critical issue for the successful application of ANN is the training of the network by a large amount of data in various engine conditions (different speed/load conditions in normal condition, and with different locations/levels of faults). On the other hand, the latest simulation technology provides a useful alternative in that the effect of clearance changes may readily be explored without recourse to cutting metal, in order to create enough training data for the ANNs. In this paper, based on some existing simplified models of piston slap, an advanced multi-body dynamic simulation software was used to simulate piston slap faults with different speeds/loads and clearance conditions. Meanwhile, the simulation models were validated and updated by a series of experiments. Three-stage network systems are proposed to diagnose piston faults: fault detection, fault localisation and fault severity identification. Multi Layer Perceptron (MLP) networks were used in the detection stage and severity/prognosis stage and a Probabilistic Neural Network (PNN) was used to identify which cylinder has faults. Finally, it was demonstrated that the networks trained purely on simulated data can efficiently detect piston slap faults in real tests and identify the location and severity of the faults as well.

AR Feels "Softer" than VR: Haptic Perception of Stiffness in Augmented versus Virtual Reality.

PubMed

Gaffary, Yoren; Le Gouis, Benoit; Marchal, Maud; Argelaguet, Ferran; Arnaldi, Bruno; Lecuyer, Anatole

2017-11-01

Does it feel the same when you touch an object in Augmented Reality (AR) or in Virtual Reality (VR)? In this paper we study and compare the haptic perception of stiffness of a virtual object in two situations: (1) a purely virtual environment versus (2) a real and augmented environment. We have designed an experimental setup based on a Microsoft HoloLens and a haptic force-feedback device, enabling to press a virtual piston, and compare its stiffness successively in either Augmented Reality (the virtual piston is surrounded by several real objects all located inside a cardboard box) or in Virtual Reality (the same virtual piston is displayed in a fully virtual scene composed of the same other objects). We have conducted a psychophysical experiment with 12 participants. Our results show a surprising bias in perception between the two conditions. The virtual piston is on average perceived stiffer in the VR condition compared to the AR condition. For instance, when the piston had the same stiffness in AR and VR, participants would select the VR piston as the stiffer one in 60% of cases. This suggests a psychological effect as if objects in AR would feel "softer" than in pure VR. Taken together, our results open new perspectives on perception in AR versus VR, and pave the way to future studies aiming at characterizing potential perceptual biases.

A CWT-based methodology for piston slap experimental characterization

NASA Astrophysics Data System (ADS)

Buzzoni, M.; Mucchi, E.; Dalpiaz, G.

2017-03-01

Noise and vibration control in mechanical systems has become ever more significant for automotive industry where the comfort of the passenger compartment represents a challenging issue for car manufacturers. The reduction of piston slap noise is pivotal for a good design of IC engines. In this scenario, a methodology has been developed for the vibro-acoustic assessment of IC diesel engines by means of design changes in piston to cylinder bore clearance. Vibration signals have been analysed by means of advanced signal processing techniques taking advantage of cyclostationarity theory. The procedure departs from the analysis of the Continuous Wavelet Transform (CWT) in order to identify a representative frequency band of piston slap phenomenon. Such a frequency band has been exploited as the input data in the further signal processing analysis that involves the envelope analysis of the second order cyclostationary component of the signal. The second order harmonic component has been used as the benchmark parameter of piston slap noise. An experimental procedure of vibrational benchmarking is proposed and verified at different operational conditions in real IC engines actually equipped on cars. This study clearly underlines the crucial role of the transducer positioning when differences among real piston-to-cylinder clearances are considered. In particular, the proposed methodology is effective for the sensors placed on the outer cylinder wall in all the tested conditions.

A 1987 overview of free-piston Stirling technology for space power application

NASA Technical Reports Server (NTRS)

Slaby, Jack G.; Alger, Donald L.

1987-01-01

An overview is presented of the NASA Lewis Research Center free-piston Stirling engine activities directed toward space-power application. NASA Lewis serves as the project office to manage the newly initiated NASA SP-100 Advanced Technology Program. One of the major elements of this five-year program is the development of advanced power conversion concepts of which the Stirling cycle is a viable growth candidate. Under this program the status of the 25 kWe opposed-piston Space Power Demonstrator Engine (SPDE) is presented. Included in the SPDE discussion are comparisons between predicted and experimental engine performance, enhanced performance resulting from regenerator modification, increased operating stroke brought about by isolating the gas bearing flow between the displacer and power piston, identifying excessive energy losses and recommending corrective action, and a better understanding of linear alternator design and operation. Technology work is also conducted on heat exchanger concepts, both design and fabrication. Design parameters and conceptual design features are also presented for a 25 kWe, single-cylinder free-piston Stirling space-power converter.

Numerical studies of the formation and destruction of vortices in a motored four-stroke piston-cylinder configuration

NASA Technical Reports Server (NTRS)

Schock, H. J.; Sosoka, D. J.; Ramos, J. I.

1983-01-01

A finite-difference procedure which solves the conservation equations of mass, momentum, and energy is used to investigate the effects of the compression ratio, engine speed, bore-to-stroke ratio, and air intake flow angle on the turbulent flow field within an axisymmetric piston-cylinder configuration. It is shown that in a four-stroke piston-cylinder configuration, the intake stroke is characterized by the formation of a piston vortex. The piston vortex is stretched during the intake stroke, and the head vortex has an almost constant diameter. For a 0-deg air intake flow angle, both vortices disappear by the end of the compression stroke; for an air intake flow angle of 45 deg, the flow field within the cylinder shows three elongated vortices which persist into the compression stroke and then break up and merge. It is also shown that larger bore-to-stroke ratios give rise to lower turbulent levels than smaller bore-to-stroke ratios and that the turbulent intensity is almost independent of the rpm.

Stochastic stability assessment of a semi-free piston engine generator concept

NASA Astrophysics Data System (ADS)

Kigezi, T. N.; Gonzalez Anaya, J. A.; Dunne, J. F.

2016-09-01

Small engines, as power generators with low-noise and vibration characteristics, are needed in two niche application areas: as electric vehicle range extenders and as domestic micro Combined Heat and Power systems. A recent semi-free piston design known as the AMOCATIC generator fully meets this requirement. The engine potentially allows for high energy conversion efficiencies at resonance derived from having a mass and spring assembly. As with free-piston engines in general, stability and control of piston motion has been cited as the prime challenge limiting the technology's widespread application. Using physical principles, we derive in this paper two important results: an energy balance criterion and a related general stability criterion for a semi-free piston engine. Control is achieved by systematically designing a Proportional Integral (PI) controller using a control-oriented engine model for which a specific stability condition is stated. All results are presented in closed form throughout the paper. Simulation results under stochastic pressure conditions show that the proposed energy balance, stability criterion, and PI controller, operate as predicted to yield stable engine operation at fixed compression ratio.

Comparison of Heavy-Duty Scuffing Behavior between Chromium-Based Ceramic Composite and Nickel-Chromium-Molybdenum-Coated Ring Sliding against Cast Iron Liner under Starvation

PubMed Central

Shen, Yan; Yu, Baihong; Lv, Yutao; Li, Bin

2017-01-01

A running-in and starved lubrication experiment is designed to investigate the heavy-duty scuffing behavior of piston ring coatings against cast iron (Fe) cylinder liner using the piston ring reciprocating liner test rig. The scuffing resistance of the piston ring with the chromium-based ceramic composite coating (CKS), and that with the thermally sprayed nickel-chromium-molybdenum coating (NCM) is compared at different nominal pressures (40~100 MPa) and temperatures (180~250 °C). With the failure time as a criterion, the rank order is as follows: NCM/Fe > CKS/Fe. Before the scoring occurs at the interface of the piston ring and cylinder liner (PRCL), the cast iron liner enters into a “polish wear” stage, and iron-based adhesive materials begin to form on the piston ring surface. With the macroscopic adhesion formation, the plastic shearing cycle causes surface damages mainly due to abrasive effects for the CKS/Fe pairs and adhesive effects for the NCM/Fe pairs. PMID:29036911

Development and Testing of a Novel Green Propellant Piston Tank

NASA Technical Reports Server (NTRS)

Diaz, C. E.; Cavender, D. P.; Higdon, K.; Abrams, J.; Duchek, M. E.; Mader, H.

2017-01-01

Analytical Mechanics Associates (AMA), in cooperation with NASA Marshall Space Flight Center's (MSFC's) Spacecraft Propulsion Systems Branch, developed and tested a novel propellant tank design that employs an internal piston pressurized with an inert gas to expel propellant to thrusters. During the course of this activity, AMA designed, oversaw fabrication, and delivered to MSFC for testing, a piston propellant tank sized for 3U or larger CubeSats. MSFC conducted liquid expulsion testing using ethylene glycol as a referee fluid to map the tank's performance at different pressures and piston positions. Following the expulsion test campaign, the tank is planned to be integrated into a propulsion system test bed for hot fire tests with a 100mN monopropellant thruster to evaluate the tank's influence on thruster performance when operated in a flight like manner. Described in this paper is a comprehensive summary of how the tanks were designed, built, and tested. The fundamental knowledge gained through the fabrication and testing of these tanks gives evidence that the piston tank design may be scalable to meet the requirements and constraints of other small satellites.

Improved piston ring materials for 650 deg C service

NASA Technical Reports Server (NTRS)

Bjorndahl, W. D.

1986-01-01

A program to develop piston ring material systems which will operate at 650C was performed. In this program, two candidate high temperature piston ring substrate materials, Carpenter 709-2 and 440B, were hot formed into the piston ring shape and subsequently evaluated. In a parallel development effort ceramic and metallic piston ring coating materials were applied to cast iron rings by various processing techniques and then subjected to thermal shock and wear evaluation. Finally, promising candidate coatings were applied to the most thermally stable hot formed substrate. The results of evaluation tests of the hot formed substrate show that Carpenter 709-2 has greater thermal stability than 440B. Of the candidate coatings, plasma transferred arc (PTA) applied tungsten carbide and molybdenum based systems exhibit the greatest resistance to thermal shock. For the ceramic based systems, thermal shock resistance was improved by bond coat grading. Wear testing was conducted to 650C (1202F). For ceramic systems, the alumina/titania/zirconia/yttria composition showed highest wear resistance. For the PTA applied systems, the tungsten carbide based system showed highest wear resistance.

Teflon-wire piston or stainless-steel bucket stapes prosthesis: does it make a difference?

PubMed

Farrior, J B; Temple, A E

1999-04-01

The goal of this study was to determine whether postoperative (implantation of a stapes prosthesis) hearing gain and the amount of air-bone gap overclosure are more improved with the Teflon-wire piston or with the stainless-steel bucket prosthesis. We retrospectively reviewed the outcomes of 82 surgeries that had been performed by the primary author; 41 of these patients had received a Fisch Teflon-wire piston, and 41 had received a Bailey-modified Robinson stainless-steel bucket prosthesis. The mean hearing gain for the patients who received the Teflon-wire piston was 23.3 dB after primary stapes surgery and 20.5 dB after revision surgery. Patients who received the stainless-steel bucket prosthesis experienced a mean hearing gain of 20.7 and 20.3 dB, respectively. Following primary stapes surgery, the air-bone gap overclosure was 4.4 dB with the Teflon-wire piston and 5.2 dB with the stainless-steel bucket prosthesis. There was no statistically significant difference in either hearing gain or air-bone gap overclosure between the two prostheses.

Development of Gas-Lubricated Pistons for Heavy Duty Diesel Engine Technology Program

NASA Technical Reports Server (NTRS)

Shapiro, W.

1984-01-01

Static testing of a segmented, gas-lubricated, piston-ring was accomplished. The ring utilizes high-pressure gas generated during the diesel cycle to energize a hydrostatic gas film between the piston and cylinder liner. The configuration was deficient in overall performance, because all segments of a ring set failed to form a fluid-film simultaneously, when exposed to internal preload. The difficulty was traced to the moment balance required to prevent the segments from overturning and contacting the cylinder walls. Some individual sectors formed a film and performed well in every respect including load capability to 6,000 N. These results produce optimism as to the ultimate feasibility of hydrostatic, gas-lubricated piston rings. In addition to test results, the principles of operation, and theoretical developments are presented. Breathable liner concepts are suggested for future consideration. In these configurations, solid hydrostatic pistons are coupled with flexible liners that elastically deform to form a gas-film under hydrostatic pressurization. Breathable liners afford the mechanical simplicity required for mass produced engines, and initial examination indicates satisfactory operation.

Component improvement of free-piston Stirling engine key technology for space power

NASA Technical Reports Server (NTRS)

Alger, Donald L.

1988-01-01

The successful performance of the 25 kW Space Power Demonstrator (SPD) engine during an extensive testing period has provided a baseline of free piston Stirling engine technology from which future space Stirling engines may evolve. Much of the success of the engine was due to the initial careful selection of engine materials, fabrication and joining processes, and inspection procedures. Resolution of the few SPD engine problem areas that did occur has resulted in the technological advancement of certain key free piston Stirling engine components. Derivation of two half-SPD, single piston engines from the axially opposed piston SPD engine, designated as Space Power Research (SPR) engines, has made possible the continued improvement of these engine components. The two SPR engines serve as test bed engines for testing of engine components. Some important fabrication and joining processes are reviewed. Also, some component deficiencies that were discovered during SPD engine testing are described and approaches that were taken to correct these deficiencies are discussed. Potential component design modifications, based upon the SPD and SPR engine testing, are also reported.

Measurement of food texture by an acoustic vibration method

NASA Astrophysics Data System (ADS)

Sakurai, Naoki; Taniwaki, Mitsuru; Iwatani, Shin-ichiro; Akimoto, Hidemi

2011-09-01

Food texture was measured by a new acoustic vibration method. A piezoelectric sensor sandwiched between a probe and piston was inserted into a food sample by delivery of silicon oil to a cylinder by a pump. Vibration emitted from the food sample on insertion of the probe was monitored by voltage outputs of the sensor. The voltage signals were passed through 19 half octave bands to calculate texture index for each band. The texture index was defined as vibration energy of the probe caused by the food rupture and/or breakage per unit time.

Design and construction of the X-2 two-stage free piston driven expansion tube

NASA Technical Reports Server (NTRS)

Doolan, Con

1995-01-01

This report outlines the design and construction of the X-2 two-stage free piston driven expansion tube. The project has completed its construction phase and the facility has been installed in the new impulsive research laboratory where commissioning is about to take place. The X-2 uses a unique, two-stage driver design which allows a more compact and lower overall cost free piston compressor. The new facility has been constructed in order to examine the performance envelope of the two-stage driver and how well it couple to sub-orbital and super-orbital expansion tubes. Data obtained from these experiments will be used for the design of a much larger facility, X-3, utilizing the same free piston driver concept.

Analysis of a system modelling the motion of a piston in a viscous gas

NASA Astrophysics Data System (ADS)

Maity, Debayan; Takahashi, Takéo; Tucsnak, Marius

2017-09-01

We study a free boundary problem modelling the motion of a piston in a viscous gas. The gas-piston system fills a cylinder with fixed extremities, which possibly allow gas from the exterior to penetrate inside the cylinder. The gas is modeled by the 1D compressible Navier-Stokes system and the piston motion is described by the second Newton's law. We prove the existence and uniqueness of global in time strong solutions. The main novelty brought in by our results is that they include the case of nonhomogeneous boundary conditions which, as far as we know, have not been studied in this context. Moreover, even for homogeneous boundary conditions, our results require less regularity of the initial data than those obtained in previous works.

RE-1000 free-piston Stirling engine update

NASA Technical Reports Server (NTRS)

Schreiber, J. G.

1985-01-01

A free piston Stirling engine was tested. The tests performed over the past several years on the single cylinder engine were designed to investigate the dynamics of a free piston Stirling engine. The data are intended to be used primarily for computer code validation. The tests designed to investigate the sensitivity of the engine performance to variations in working space pressure, heater and cooler temperatures, regenerator porosity, power piston mass and displacer dynamics were completed. In addition, some data were recorded with alternate working fluids. A novel resonant balance system for the engine was also tested. Some preliminary test results of the tests performed are presented along with an outline of future tests to be run with the engine coupled to a hydraulic output unit. A description of the hydraulic output unit is given.

Solids feeder apparatus

DOEpatents

Bell, Jr., Harold S.

1979-01-01

This invention sets forth a double-acting piston, which carries a floating piston, and which is reciprocated in a housing, for feeding coal to a high pressure gasifier system. The housing has a plurality of solids (for instance: coal) in-feeding ports and a single discharge port, the latter port being in communication with a high pressure gasifier system. The double-acting piston sequentially and individually communicates each of the in-feeding ports with the discharge port. The floating piston both seals off the discharge port while each in-feeding port is receiving coal or the like, to prevent undue escape of gas from the gasifier system, and translates in the housing, following a discharge of coal or the like into the discharge port, to return gas which has been admitted into the housing back into the gasifier system.

Nitrited-Steel Piston Rings for Engines of High Specific Power

NASA Technical Reports Server (NTRS)

Collins, John H; Bisson, Edmond E; Schmiedlin, Ralph F

1945-01-01

Stability and control characteristics determined from tests in the Langley 19-foot pressure tunnel of a 0.2375-scale model of the Douglas XA-26 airplane are compared with those measured in flight tests of a Douglas A-26b airplane. Several designs of nitrided-steel piston rings were performance-tested under variable conditions of output. The necessity of good surface finish and conformity of the ring to the bore was indicated in the preliminary tests. Nitrided-steel rings of the same dimensions as cast-iron rings operating on the original piston were unsatisfactory, and the final design was a lighter, rectangular, thin-face-width ring used on a piston having a maximum cross-head area and a revised skirt shape. Results were obtained from single-cylinder and multicylinder engine runs.

Reduction of the uncertainty of the PTB vacuum pressure scale by a new large area non-rotating piston gauge

NASA Astrophysics Data System (ADS)

Bock, Th; Ahrendt, H.; Jousten, K.

2009-10-01

This paper describes the metrological characterization of a new large area piston gauge (FRS5, Furness Rosenberg Standard) installed at the vacuum metrology laboratory of the Physikalisch-Technische Bundesanstalt (PTB). The operational procedure and the uncertainty budget for pressures between 30 Pa and 11 kPa are given. Comparisons between the FRS5 and a mercury manometer, a rotary piston gauge and a force-balanced piston gauge are described. We show that the reproducibility of the calibration values of capacitance diaphragm gauges is enhanced by a factor of 6 compared with a static expansion primary standard (SE2). Improvements of the SE2 performance by reducing the number of expansions and smaller uncertainties of expansion ratios are discussed.

Vortex Formation During Unsteady Boundary-Layer Separation

NASA Astrophysics Data System (ADS)

Das, Debopam; Arakeri, Jaywant H.

1998-11-01

Unsteady laminar boundary-layer separation is invariably accompanied by the formation of vortices. The aim of the present work is to study the vortex formation mechanism(s). An adverse pressure gradient causing a separation can be decomposed into a spatial component ( spatial variation of the velocity external to the boundary layer ) and a temporal component ( temporal variation of the external velocity ). Experiments were conducted in a piston driven 2-D water channel, where the spatial component could be be contolled by geometry and the temporal component by the piston motion. We present results for three divergent channel geometries. The piston motion consists of three phases: constant acceleration from start, contant velocity, and constant deceleration to stop. Depending on the geometry and piston motion we observe different types of unsteady separation and vortex formation.

Tubing and cable cutting tool

NASA Technical Reports Server (NTRS)

Mcsmith, D. D.; Richardson, J. I. (Inventor)

1984-01-01

A hand held hydraulic cutting tool was developed which is particularly useful in deactivating ejection seats in military aircraft rescue operations. The tool consists primarily of a hydraulic system composed of a fluid reservoir, a pumping piston, and an actuator piston. Mechanical cutting jaws are attached to the actuator piston rod. The hydraulic system is controlled by a pump handle. As the pump handle is operated the actuator piston rod is forced outward and thus the cutting jaws are forced together. The frame of the device is a flexible metal tubing which permits easy positioning of the tool cutting jaws in remote and normally inaccessible locations. Bifurcated cutting edges ensure removal of a section of the tubing or cable to thereby reduce the possibility of accidental reactivation of the tubing or cable being severed.

Nozzle seal

DOEpatents

Groff, Russell Dennis; Vatovec, Richard John

1978-06-11

In an illustrative embodiment of the invention, a nuclear reactor pressure vessel, having an internal hoop from which the heated coolant emerges from the reactor core and passes through to the reactor outlet nozzles, is provided with annular sealing members operatively disposed between the outlet nozzle and the hoop and partly within a retaining annulus formed in the hoop. The sealing members are biased against the pressure vessel and the hoop and one of the sealing members is provided with a piston type pressure ring sealing member which effectively closes the path between the inlet and outlet coolants in the region about the outlet nozzle establishing a leak-proof condition. Furthermore, the flexible responsiveness of the seal assures that the seal will not structurally couple the hoop to the pressure vessel.

Physical properties of northern Gulf of Mexico sediment and laboratory samples containing natural and synthetic methane gas hydrate

NASA Astrophysics Data System (ADS)

Winters, W. J.; Waite, W. F.; Mason, D. H.; Lorenson, T. L.; Paull, C. K.; Novosel, I.; Boldina, O. M.; Dallimore, S. R.; Collett, T. S.; Page 127 Shipboard Sc. Party

2003-04-01

The U.S. Geological Survey (USGS) has been involved in oceanographic and Arctic field programs and laboratory studies to better understand the relationship between natural gas hydrate and physical properties of surrounding sediment. Recently, the Institut Polaire Francais, Paul-Emile Victor (IPEV) and the USGS jointly conducted a cruise aboard the Marion Dufresne to collect giant piston cores to determine the distribution of gas hydrate in the northern Gulf of Mexico. Hydrates recovered during the cruise did not appear to be lithologically controlled (unlike Canadian Arctic cores) and were either disseminated or were massive layers. Sediment water content typically decreases rapidly to a subbottom depth of about 8 to 9 m, but then decreases at a lower rate. At-sea help was provided by the IMAGES (International Marine Past Global Changes Study) and PAGE (Paleoceanography of the Atlantic and Geochemistry) programs, and funding was provided by the U.S. Dept. of Energy. We have used the Gas Hydrate And Sediment Test Laboratory Instrument (GHASTLI) to analyze sediment containing natural gas hydrate and to examine hydrate formed within (a) initially water-saturated and (b) partly-water saturated sieved Ottawa sand specimens at a pore pressure of 12 MPa and 250 kPa confining stress. Hydrate is formed when methane gas is slowly percolated into a 70-mm diameter by 140-mm long cylindrical specimen and subsequently the temperature is lowered to about 6 degrees C. We have found that acoustic velocity, shear strength, and permeability of samples containing different initial water contents are significantly affected by (a) the amount of hydrate present, (b) its distribution, (c) its position within pores, and (d) concentration at key locations. Acoustic P-wave velocities can increase from 1.7 km/s to 4.0 km/s using different hydrate and synthetic sample formation techniques. Although acoustic properties are significantly affected by hydrate at grain boundaries, the mere presence of hydrate in pores (but not necessarily at grain contacts) causes strength to significantly increase because dilation during undrained shear results in greater negative pore pressures. Recently determined strengths of three Ottawa sand samples are exponentially related to the degree of water saturation, bulk density, and hydrate content.

High Concentration of Methane and Magnificent gas Plumes Over gas Hydrate Field in the Eastern Margin of Japan Sea

NASA Astrophysics Data System (ADS)

Ishida, Y.; Matsumoto, R.; Hiruta, A.; Aoyama, C.; Tomaru, H.; Hiromatsu, M.

2005-12-01

Gas hydrates and prominent pockmarks have been observed on the Umitaka Spur in the eastern margin of Japan Sea, at the depth of about 900 m.Magnificent methane plumes, 550 to 600 m high, were detected by echo sounder for fish school, and massive gas hydrates were recovered by piston coring during the UT04 cruise of R/V Umitaka-maru (2004). The seawater over this area was collected by CTD and the samples of interstitial waters were extracted from sediment cores by hydraulic squeezer. The ratio of methane to ethane concentration (C1/C2) and the isotopic (δ 13C) composition of methane in the plume sites are less than 103 and from -40 to -50 (‰ PDB) respectively, suggesting that the origin of such gases are mostly thermogenic, whereas the gases in the sediments away from plumes are mostly microbial. The seawater samples demonstrated anomalously high concentration of methane over the plume sites. Maximum concentration is 160nmol/L above the methane plume site. The methane concentration values of most samples ranged from 4 to 6nmol/L. When it compared with the Nankai Trough (1 to 4nmol/L), even the base level methane is quite high. Seawater samples collected at the depth of 200 m exhibit sharp anomalies of 16 to 34nmol/L. With the intension to check the possibility of the inflow from the shelf and river waters, we collected surface waters far away from the Umitaka spur. Methane concentration was only 7nmol/L. Therefore, we conclude that anomalously high concentration at 200 m level over the spur is not likely to be explained by inflow of shelf waters, but also by methane seeps. The temperature of waters are extremely low from 0.25°C to 1.0°C below 300 m, then abruptly increases in shallow waters to about 25°C at surface water. Thus, bottom and intermediate waters are within the stability condition of methane hydrate. Under these conditions, gases from the sea floor would form gas hydrate within bottom water mass. Gas hydrate crystals would float up shallow to the water mass where they dissociate to supply methane at around 300 m due to abrupt temperature increase.

Well pump

DOEpatents

Ames, Kenneth R.; Doesburg, James M.

1987-01-01

A well pump includes a piston and an inlet and/or outlet valve assembly of special structure. Each is formed of a body of organic polymer, preferably PTFE. Each includes a cavity in its upper portion and at least one passage leading from the cavity to the bottom of the block. A screen covers each cavity and a valve disk covers each screen. Flexible sealing flanges extend upwardly and downwardly from the periphery of the piston block. The outlet valve block has a sliding block and sealing fit with the piston rod.

Self-charging metering and dispensing device for fluids

NASA Technical Reports Server (NTRS)

Hooper, S. L.; Setzer, D. (Inventor)

1984-01-01

A self-metering and dispensing device for fluids obtained from a pressurized fluid supply is discussed. Tubing and valving means permit the introduction of fluid into and discharge from a closed cylindrical reservoir. The reservoir contains a slideably disposed piston co-acting with a coil compression spring, with piston travel determining the amount of fluid in the reservoir. Once the determined amount of fluid is introduced into the reservoir, the fluid is discharged by the force of the coil compression spring acting upon the piston.

Integral finned heater and cooler for stirling engines

DOEpatents

Corey, John A.

1984-01-01

A piston and cylinder for a Stirling engine and the like having top and bottom meshing or nesting finned conical surfaces to provide large surface areas in close proximity to the working gas for good thermal (addition and subtraction of heat) exchange to the working gas and elimination of the usual heater and cooler dead volume. The piston fins at the hot end of the cylinder are perforated to permit the gas to pass into the piston interior and through a regenerator contained therein.

Power control for heat engines

DOEpatents

Dineen, John J.

1984-01-01

A power control arrangement for a Stirling engine includes a sleeve mounted in each cylinder for axial movement and a port in the sleeve leading to a dead space. The port is covered by the piston at a position that is determined by the piston position and the axial adjustment of the sleeve. The compression phase of the Stirling cycle for that piston begins when the port is covered, so the position of the sleeve is used to set the Stirling engine power level.

Mathematical modeling of bent-axis hydraulic piston motors

NASA Technical Reports Server (NTRS)

Bartos, R. D.

1992-01-01

Each of the DSN 70-m antennas uses 16 bent-axis hydraulic piston motors as part of the antenna drive system. On each of the two antenna axes, four motors are used to drive the antenna and four motors provide counter torque to remove the backlash in the antenna drive train. This article presents a mathematical model for bent-axis hydraulic piston motors. The model was developed to understand the influence of the hydraulic motors on the performance of the DSN 70-m antennas' servo control system.

The Adiabatic Piston and the Second Law of Thermodynamics

NASA Astrophysics Data System (ADS)

Crosignani, Bruno; Di Porto, Paolo; Conti, Claudio

2002-11-01

A detailed analysis of the adiabatic-piston problem reveals peculiar dynamical features that challenge the general belief that isolated systems necessarily reach a static equilibrium state. In particular, the fact that the piston behaves like a perpetuum mobile, i.e., it never stops but keeps wandering, undergoing sizable oscillations, around the position corresponding to maximum entropy, has remarkable implications on the entropy variations of the system and on the validity of the second law when dealing with systems of mesoscopic dimensions.

Advanced Small Free-Piston Stirling Convertors for Space Power Applications

NASA Astrophysics Data System (ADS)

Wood, J. Gary; Lane, Neill

2004-02-01

This paper reports on the current status of an advanced 35 We free-piston Stirling convertor currently being developed under NASA SBIR Phase II funding. Also described is a further advanced and higher performance ~80 watt free-piston convertor being developed by Sunpower and Boeing/Rocketdyne for NASA under NRA funding. Exceptional overall convertor (engine plus linear alternator) thermodynamic performance (greater than 50% of Carnot) with specific powers around 100 We /kg appear reasonable at these low power levels.

Lightweight piston-rod assembly for a reciprocating machine

DOEpatents

Corey, John A.; Walsh, Michael M.

1986-01-01

In a reciprocating machine, there is provided a hollow piston including a dome portion on one end and a base portion on the opposite end. The base portion includes a central bore into which a rod is hermetically fixed in radial and angular alignment. The extending end of the rod has a reduced diameter portion adapted to fit into the central bore of a second member such as a cross-head assembly, and to be secured thereto in radial and axial alignment with the piston.

Investigations of Parametric Excitation in Physical Systems

DTIC Science & Technology

2005-06-01

utility purposes. The most common and readily thought of was the standard lawn mower engine. These engines could exceed over 2 inches in piston diameter...and stroke length, as well as meet the need for only one piston. For this reason it was decided that a lawn mower engine would be used for the...examined several lawn mower engines and selecting the one with the la e to the piston cylinder was the next line of action. Upon removing all extraneous

Wear resistance of a metal surface modified with minerals

NASA Astrophysics Data System (ADS)

Kislov, S. V.; Kislov, V. G.; Balasch, P. V.; Skazochkin, A. V.; Bondarenko, G. G.; Tikhonov, A. N.

2016-02-01

The article describes the advantages of the new technology of mineral coating of metal products for the friction pair of mechanical systems. It presents the research results of the wear rate of the samples made of 12X13 steel (X12Cr13) with mineral layers, in the experiments with a piston ring sliding inside a cylinder liner with grease. The wear rate of the samples with mineral layers is lower almost by two factors than that of the samples made of grey foundry iron and untreated samples. As the result of slip/rolling abrasion tests of parts with mineral layers under conditions of high contact pressure, a suggestion was made concerning probable mechanics of surface wear.

Nitrogen partitioning during Earth's accretion and core-mantle differentiation

NASA Astrophysics Data System (ADS)

Speelmanns, I. M.; Schmidt, M. W.; Liebske, C.

2017-12-01

On present day Earth, N is one of the key constituents of our atmosphere and forms the basis of life. However, the deep Earth geochemistry of N, i.e. its distribution and isotopic fractionation between Earth's deep reservoirs is not well constrained. This study investigates nitrogen partitioning between metal and silicate melts as relevant for core segregation during the accretion of planetesimals into the Earth. We have determined N-partitioning coefficients over a wide range of temperatures (1250-2000 °C), pressures (15-35 kbar) and oxygen fugacity's, the latter in the relevant range of core segregation (IW-5 to IW). Centrifuging piston cylinders were used to equilibrate and then gravitationally separate metal-silicate melt pairs. Separation of the two melts is necessary to avoid micro nugget contamination in the silicate melt at reducing conditions < IW-2.5. Complete segregation of the two melts was reached within 1 to 3 hours at 1000 g and 1600-1250 °C respectively, the interface showing a proper meniscus. The applied double capsule technique in all experiments, using an outer metallic (Pt) and inner non-metallic capsule (graphite or Al2O3), minimizes N-loss over the course of the experiments compared to single non-metallic capsules. The two quenched melts were cut apart mechanically, cleaned at the outside, their N concentrations were then analysed on bulk samples by an elemental analyser, the low abslute masses requiring careful development of analytical routines. Despite these difficulties, we were able to determine a DNmetal/silicate of 13±0.3 at IW-1 decreasing to 2.0±0.2 at IW-5.5, at 1250°C and 15 kbar, N partitioning into the core forming metal. Increasing temperature dramatically lowers the DNmetal/silicate to e.g. 0.5±0.15 at IW-4, during early core formation N was hence mildly incompatible in the metal. The results suggest that under magma ocean conditions (> 2000 oC and fO2 IW-2.5), N-partition coefficents were within a factor of 2 of unity. Hence, N did not partition into the core, which should contain negliligible quantities of N. The few available literature data [1],[2],[3] support N changing compatibility with decreasing fO2. [1] Kadik et al., (2011) Geochem Int 49.5: 429-438. [2] Roskosz et al., (2013) GCA 121: 15-28. [3] Dalou et al., (2017) EPSL 458: 141-151

Experiments on the formation and properties of thin vortex rings in water.

NASA Astrophysics Data System (ADS)

Donnelly, Russell; Stange, Alex; Julian, Brian

2001-11-01

We have been experimenting for some time with a vortex gun 2.54 cm in diameter with a piston powered by a small servo motor . Strokes can be generated up to about 3 cm. The object has been to determine the properties of the rings formed by this gun as if they were thin rings in an inviscid fluid. That is, we are trying to characterize the rings by their radius, core parameter, velocity, and circulation. We are also studying the slowing of these rings as they propagate across the tank. Visualization is by means of an electrochemical (Baker) technique. In general the rings propagate with nearly constant radius and speed. The core size remains apparently unchanged, as would be expected with our visualization technique. We are able to propagate rings with velocities up to about 35 cm/s. Their radius at the exit of the gun grows with the stroke length. The core parameter and circulation appear fairly consistent with the slug model. We are attempting to devise a method of measuring the impulse of the vortex ring in flight, and will report on progress. The ultimate goal of the experiment is to study collisions of rings, and the role of reconnections for thin vortices.

Seismic peak amplitude as a predictor of TOC content in shallow marine sediments

NASA Astrophysics Data System (ADS)

Neto, Arthur Ayres; Mota, Bruno Bourguignon; Belem, André Luiz; Albuquerque, Ana Luiza; Capilla, Ramsés

2016-10-01

Acoustic remote sensing is a highly effective tool for exploring the seafloor of both deep and shallow marine settings. Indeed, the acoustic response depends on several physicochemical factors such as sediment grain size, bulk density, water content, and mineralogy. The objective of the present study is to assess the suitability of seismic peak amplitude as a predictor of total organic carbon (TOC) content in shallow marine sediments, based on data collected in the Cabo Frio mud belt in an upwelling zone off southeastern Brazil. These comprise records of P-wave velocity ( V P) along 680 km of high-resolution single-channel seismic surveys, combined with analyses of grain size, wet bulk density, absolute water content and TOC content for four piston-cores. TOC contents of sediments from 13 box-cores served to validate the methodology. The results show well-defined positive correlations between TOC content and mean grain size (phi scale) as well as absolute water content, and negative correlations with V P, wet bulk density, and acoustic impedance. These relationships yield a regression equation by which TOC content can be satisfactorily predicted on the basis of acoustic impedance for this region: y = - 4.84 ln( x) + 40.04. Indeed, the derived TOC contents differ by only 5% from those determined by geochemical analysis. After appropriate calibration, acoustic impedance can thus be conveniently used as a predictor of large-scale spatial distributions of organic carbon enrichment in marine sediments. This not only contributes to optimizing scientific project objectives, but also enhances the cost-effectiveness of marine surveys by greatly reducing the ship time commonly required for grid sampling.

Methane-derived authigenic carbonates from the northern Gulf of Mexico - MD02 Cruise

USGS Publications Warehouse

Chen, Y.; Matsumoto, R.; Paull, C.K.; Ussler, W.; Lorenson, T.; Hart, P.; Winters, W.

2007-01-01

Authigenic carbonates were sampled in piston cores collected from both the Tunica Mound and the Mississippi Canyon area on the continental slope of the northern Gulf of Mexico during a Marion Dufresne cruise in July 2002. The carbonates are present as hardgrounds, porous crusts, concretions or nodules and shell fragments with or without carbonate cements. Carbonates occurred at gas venting sites which are likely to overlie gas hydrates bearing sediments. Electron microprobe, X-ray diffraction (XRD) and thinsection investigations show that these carbonates are high-Mg calcite (6-21??mol% MgCO3), with significant presence of framboidal pyrite. All carbonates are depleted in 13C (??13C = - 61.9 to - 31.5??? PDB) indicating that the carbon is derived mainly from anaerobic methane oxidation (AMO). Age estimates based on 14C dating of shell fragments and on regional sedimentation rates indicate that these authigenic carbonates formed within the last 1000??yr in the Mississippi Canyon and within 5500??yr at the Tunica Mound. The oxygen isotopic composition of carbonates ranges from + 3.4 to + 5.9??? PDB. Oxygen isotopic compositions and Mg2+ contents of carbonates, and present in-situ temperatures of bottom seawater/sediments, show that some of these carbonates, especially from a core associated with underlying massive gas hydrates precipitated in or near equilibrium with bottom-water. On the other hand, those carbonates more enriched in 18O are interpreted to have precipitated from 18O-rich fluids which are thought to have been derived from the dissociation of gas hydrates. The dissociation of gas hydrates in the northern Gulf of Mexico within the last 5500??yr may be caused by nearby salt movement and related brines. ?? 2007 Elsevier B.V. All rights reserved.

Gamma radiation effects on the dynamic fatigue measurements of glass discs

NASA Technical Reports Server (NTRS)

Ananaba, T. O. J.; Kinser, D. L.

1985-01-01

Circular specimens of low iron soda lime silicate glass were blasted with grit after having a circular notch etched into their centers. After separation into two groups, one group was exposed to gamma radiation. The fracture strengths of all samples were then tested by the biaxial technique, i.e., specimens were balanced on three balls and loaded in the center by a piston. The irradiated samples had received a 140,000 Gy dose from a Co-60 source. An enhanced interaction between the ambient moisture and the grit-blasted central notch was observed in the irradiated samples, which displayed accelerated corrosion.

Critical velocities for deflagration and detonation triggered by voids in a REBO high explosive

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herring, Stuart Davis; Germann, Timothy C; Jensen, Niels G

2010-01-01

The effects of circular voids on the shock sensitivity of a two-dimensional model high explosive crystal are considered. We simulate a piston impact using molecular dynamics simulations with a Reactive Empirical Bond Order (REBO) model potential for a sub-micron, sub-ns exothermic reaction in a diatomic molecular solid. The probability of initiating chemical reactions is found to rise more suddenly with increasing piston velocity for larger voids that collapse more deterministically. A void with radius as small as 10 nm reduces the minimum initiating velocity by a factor of 4. The transition at larger velocities to detonation is studied in amore » micron-long sample with a single void (and its periodic images). The reaction yield during the shock traversal increases rapidly with velocity, then becomes a prompt, reliable detonation. A void of radius 2.5 nm reduces the critical velocity by 10% from the perfect crystal. A Pop plot of the time-to-detonation at higher velocities shows a characteristic pressure dependence.« less

Application of densification process in organic waste management.

PubMed

Zafari, Abedin; Kianmehr, Mohammad Hossein

2013-07-01

Densification of biomass material that usually has a low density is good way of increasing density, reducing the cost of transportation, and simplifying the storage and distribution of this material. The current study was conducted to investigate the influence of raw material parameters (moisture content and particle size), and densification process parameters (piston speed and die length) on the density and durability of pellets from compost manure. A hydraulic press and a single pelleter were used to produce pellets in controlled conditions. Ground biomass samples were compressed with three levels of moisture content [35%, 40% and 45% (wet basis)], piston speed (2, 6 and 10 mm/s), die length (8, 10 and 12 mm) and particle size (0.3., 0.9 and 1.5 mm) to establish density and durability of pellets. A response surface methodology based on the Box Behnken design was used to study the responses pattern and to understand the influence of parameters. The results revealed that all independent variables have significant (P < 0.01) effects on studied responses in this research.

40 CFR 86.428-80 - Maintenance, scheduled; test vehicles.

Code of Federal Regulations, 2011 CFR

2011-07-01

... necessary. For example, piston and cylinder replacement caused by piston seizure which results in the vehicle being inoperative; or in the case of two-stroke engines, decarbonization, the need for which is...

40 CFR 86.428-80 - Maintenance, scheduled; test vehicles.

Code of Federal Regulations, 2012 CFR

2012-07-01

... necessary. For example, piston and cylinder replacement caused by piston seizure which results in the vehicle being inoperative; or in the case of two-stroke engines, decarbonization, the need for which is...

40 CFR 86.428-80 - Maintenance, scheduled; test vehicles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... necessary. For example, piston and cylinder replacement caused by piston seizure which results in the vehicle being inoperative; or in the case of two-stroke engines, decarbonization, the need for which is...

40 CFR 86.428-80 - Maintenance, scheduled; test vehicles.

Code of Federal Regulations, 2014 CFR

2014-07-01

... necessary. For example, piston and cylinder replacement caused by piston seizure which results in the vehicle being inoperative; or in the case of two-stroke engines, decarbonization, the need for which is...

Free-piston engine

DOEpatents

Van Blarigan, Peter

2001-01-01

A combustion system which can utilize high compression ratios, short burn durations, and homogeneous fuel/air mixtures in conjunction with low equivalence ratios. In particular, a free-piston, two-stroke autoignition internal combustion engine including an electrical generator having a linear alternator with a double-ended free piston that oscillates inside a closed cylinder is provided. Fuel and air are introduced in a two-stroke cycle fashion on each end, where the cylinder charge is compressed to the point of autoignition without spark plugs. The piston is driven in an oscillating motion as combustion occurs successively on each end. This leads to rapid combustion at almost constant volume for any fuel/air equivalence ratio mixture at very high compression ratios. The engine is characterized by high thermal efficiency and low NO.sub.x emissions. The engine is particularly suited for generating electrical current in a hybrid automobile.

Hydrodynamic growth and decay of planar shock waves

DOE Office of Scientific and Technical Information (OSTI.GOV)

Piriz, A. R., E-mail: roberto.piriz@uclm.es; Sun, Y. B.; Tahir, N. A.

2016-03-15

A model for the hydrodynamic attenuation (growth and decay) of planar shocks is presented. The model is based on the approximate integration of the fluid conservation equations, and it does not require the heuristic assumptions used in some previous works. A key issue of the model is that the boundary condition on the piston surface is given by the retarded pressure, which takes into account the transit time of the sound waves between the piston and any position at the bulk of the shocked fluid. The model yields the shock pressure evolution for any given pressure pulse on the piston,more » as well as the evolution of the trajectories, velocities, and accelerations on the shock and piston surfaces. An asymptotic analytical solution is also found for the decay of the shock wave.« less

Analysis of optimisation method for a two-stroke piston ring using the Finite Element Method and the Simulated Annealing Method

NASA Astrophysics Data System (ADS)

Kaliszewski, M.; Mazuro, P.

2016-09-01

Simulated Annealing Method of optimisation for the sealing piston ring geometry is tested. The aim of optimisation is to develop ring geometry which would exert demanded pressure on a cylinder just while being bended to fit the cylinder. Method of FEM analysis of an arbitrary piston ring geometry is applied in an ANSYS software. The demanded pressure function (basing on formulae presented by A. Iskra) as well as objective function are introduced. Geometry definition constructed by polynomials in radial coordinate system is delivered and discussed. Possible application of Simulated Annealing Method in a piston ring optimisation task is proposed and visualised. Difficulties leading to possible lack of convergence of optimisation are presented. An example of an unsuccessful optimisation performed in APDL is discussed. Possible line of further optimisation improvement is proposed.

Locking apparatus for gate valves

DOEpatents

Fabyan, J.; Williams, C.W.

A locking apparatus for fluid operated valves having a piston connected to the valve actuator which moves in response to applied pressure within a cylinder housing having a cylinder head, a catch block is secured to the piston, and the cylinder head incorporates a catch pin. Pressure applied to the cylinder to open the valve moves the piston adjacent to the cylinder head where the catch pin automatically engages the catch block preventing further movement of the piston or premature closure of the valve. Application of pressure to the cylinder to close the valve, retracts the catch pin, allowing the valve to close. Included are one or more selector valves, for selecting pressure application to other apparatus depending on the gate valve position, open or closed, protecting such apparatus from damage due to premature closing caused by pressure loss or operational error.

Status of the NASA Stirling Radioisotope Project

NASA Technical Reports Server (NTRS)

Schreiber, Jeffrey G.

2007-01-01

Free-piston Stirling power conversion has been considered a candidate for radioisotope power systems for space for more than a decade. Prior to the free-piston Stirling architecture, systems were designed with kinematic Stirling engines that used linkages and rotary alternators to convert heat to electricity. These systems were able to achieve long life by lightly loading the linkages; however, the live was nonetheless limited. When the free-piston configuration was initially proposed, it was thought to be attractive due to the relatively high conversion efficiency, acceptable mass, and the potential for long life and high reliability based on wear-free operation. These features have consistently been recognized by teams that have studied technology options for radioisotope space power systems. Since free-piston Stirling power conversion was first considered for space power applications, there have been major advances in three general areas of development: hardware that has demonstrated long-life and reliability, the success achieved by Stirling cryocoolers in space, and the overall developmental maturity of the technology for both space and terrestrial applications. Based on these advances, free-piston Stirling convertors are currently being developed for space power, and for a number of terrestrial applications. They commonly operate with the power, efficiency, life, and reliability as intended, and much of the development now centers on system integration. This paper will summarize the accomplishments of free-piston Stirling power conversion technology over the past decade, review the status of development with regard to space power, and discuss the challenges that remain.

Compact high-efficiency linear cryocooler in single-piston moving magnet design for HOT detectors

NASA Astrophysics Data System (ADS)

Rühlich, I.; Mai, M.; Rosenhagen, C.; Withopf, A.; Zehner, S.

2012-06-01

State of the art Mid Wave IR-technology has the potential to rise the FPA temperature from 77K to 130-150K (High Operation Temperature, HOT). Using a HOT FPA will significantly lower SWaP and keep those parameters finally dominated by the employed cryocooler. Therefore, compact high performance cryocoolers are mandatory. AIM has developed the SX040 cooler, optimized for FPA temperatures of about 95K (presented at SPIE 2010). The SX040 cooler incorporates a high efficient dual piston driving mechanism resulting in a very compact compressor of less than 100mm length. Higher compactness - especially shorter compressors - can be achieved by change from dual to single piston design. The new SX030 compressor has such a single piston Moving Magnet driving mechanism resulting in a compressor length of about 60mm. Common for SX040 and SX030 family is a Moving Magnet driving mechanism with coils placed outside the helium vessel. In combination with high performance plastics for the piston surfaces this design enables lifetimes in excess of 20,000h MTTF. Because of the higher FPA temperature and a higher operating frequency also a new displacer needs to be developed. Based on the existing 1/4" coldfinger interface AIM developed a new displacer optimized for an FPA temperature of 140K and above. This paper gives an overview on the development of this new compact single piston cryocooler. Technical details and performance data will be shown.

Potential geologic hazards and constraints for blocks in proposed North Atlantic OCS Oil and gas lease sale 52

USGS Publications Warehouse

Carpenter, G.B.; Cardinell, A.P.; Francois, D.K.; Good, L.K.; Lewis, R.L.; Stiles, N.T.

1982-01-01

Analysis of high-resolution geophysical data collected over 540 blocks tentatively selected for leasing in proposed OCS Oil and Gas Lease Sale 52 (Georges Bank) revealed a number of potential geologic hazards to oil and gas exploration and development activities: evidence of mass movements and shallow gas deposits on the continental slope. No potential hazards were observed on the continental shelf or rise. Other geology-related problems, termed constraints because they pose a relatively low degree of risk and can be routinely dealt with by the use of existing technology have been observed on the continental shelf. Constraints identified in the proposed sale area are erosion, sand waves, filled channels and deep faults. Piston cores were collected for geotechnical analysis at selected locations on the continental slope in the proposed lease sale area. The core locations were selected to provide information on slope stability and to establish the general geotechnical properties of the sediments. Preliminary results of a testing program suggest that the surficial sediment cover is stable with respect to mass movement.

Pooled effect of injection pressure and turbulence inducer piston on performance, combustion, and emission characteristics of a DI diesel engine powered with biodiesel blend.

PubMed

Isaac JoshuaRamesh Lalvani, J; Parthasarathy, M; Dhinesh, B; Annamalai, K

2016-12-01

In this study, the effect of injection pressure on combustion, performance, and emission characteristics of a diesel engine powered with turbulence inducer piston was studied. Engine tests were executed using conventional diesel and 20% blend of adelfa biodiesel [A20]. The results acquired from renewable fuel A20 in the conventional engine showed reduction in brake thermal efficiency being the result of poor air fuel mixing characteristics and the higher viscosity of the tested fuel. This prompted further research aiming at the improvement of turbulence for better air fuel mixing by a novel turbulence inducer piston [TIP]. The investigation was carried out to study the combined effect of injection pressure and turbulence inducer piston. Considerable improvement in the emission characteristics like hydrocarbon, carbon monoxide, smoke was acheived as a result of optimised injection pressure. Nevertheless, the nitrogen oxide emissions were slightly higher than those of the conventional unmodified engine. The engine with turbulence inducer piston shows the scope for reducing the major pollution and thus ensures environmental safety. Copyright © 2015 Elsevier Inc. All rights reserved.

Comparison of titanium and Robinson stainless steel stapes piston prostheses.

PubMed

Lippy, William H; Burkey, John M; Schuring, Arnold G; Berenholz, Leonard P

2005-09-01

Although stainless steel stapes prostheses have generally been considered magnetic resonance imaging safe, there is concern that this may change with the development of more powerful imaging systems. The objective of the study was to determine whether a titanium piston stapes prosthesis would be audiometrically and surgically equivalent to a Robinson stainless steel piston for stapedectomy. Retrospective chart review. Private otology practice. In all, 50 patients underwent stapedectomy with a Gyrus titanium piston prosthesis. These patients were matched on the basis of age and preoperative bone-conduction scores with patients who underwent stapedectomy with a Robinson stainless steel piston prosthesis. Audiometric results are analyzed, and surgical complications noted. There was no significant difference between groups in hearing improvement or postoperative air-bone gap. The mean four-frequency hearing improvement was 27.7 dB for the stainless steel group and 27.8 dB for the titanium group. The mean postoperative air-bone gap was 2.65 dB for the stainless steel group and 2.60 for the titanium group. Neither group had a surgical complication. The titanium stapes prosthesis is a good alternative to a stainless steel prosthesis.

Time-lapse camera observations of gas piston activity at Pu`u `Ō`ō, Kīlauea volcano, Hawai`i

NASA Astrophysics Data System (ADS)

Orr, Tim R.; Rea, James C.

2012-12-01

Gas pistoning is a type of eruptive behavior described first at Kīlauea volcano and characterized by the (commonly) cyclic rise and fall of the lava surface within a volcanic vent or lava lake. Though recognized for decades, its cause continues to be debated, and determining why and when it occurs has important implications for understanding vesiculation and outgassing processes at basaltic volcanoes. Here, we describe gas piston activity that occurred at the Pu`u `Ō`ō cone, in Kīlauea's east rift zone, during June 2006. Direct, detailed measurements of lava level, made from time-lapse camera images captured at close range, show that the gas pistons during the study period lasted from 2 to 60 min, had volumes ranging from 14 to 104 m3, displayed a slowing rise rate of the lava surface, and had an average gas release duration of 49 s. Our data are inconsistent with gas pistoning models that invoke gas slug rise or a dynamic pressure balance but are compatible with models which appeal to gas accumulation and loss near the top of the lava column, possibly through the generation and collapse of a foam layer.

Validation of the Jarzynski relation for a system with strong thermal coupling: an isothermal ideal gas model.

PubMed

Baule, A; Evans, R M L; Olmsted, P D

2006-12-01

We revisit the paradigm of an ideal gas under isothermal conditions. A moving piston performs work on an ideal gas in a container that is strongly coupled to a heat reservoir. The thermal coupling is modeled by stochastic scattering at the boundaries. In contrast to recent studies of an adiabatic ideal gas with a piston [R.C. Lua and A.Y. Grosberg, J. Phys. Chem. B 109, 6805 (2005); I. Bena, Europhys. Lett. 71, 879 (2005)], the container and piston stay in contact with the heat bath during the work process. Under this condition the heat reservoir as well as the system depend on the work parameter lambda and microscopic reversibility is broken for a moving piston. Our model is thus not included in the class of systems for which the nonequilibrium work theorem has been derived rigorously either by Hamiltonian [C. Jarzynski, J. Stat. Mech. (2004) P09005] or stochastic methods [G.E. Crooks, J. Stat. Phys. 90, 1481 (1998)]. Nevertheless the validity of the nonequilibrium work theorem is confirmed both numerically for a wide range of parameter values and analytically in the limit of a very fast moving piston, i.e., in the far nonequilibrium regime.

Overview of free-piston Stirling engine technology for space power application

NASA Technical Reports Server (NTRS)

Slaby, Jack G.

1987-01-01

An overview is presented of free-piston Stirling engine activities, directed toward space power applications. One of the major elements of the program is the development of advanced power conversion. Under this program the status of the 25 kWe opposed-piston Space Power Demonstrator Engine (SPDE) is presented. Initial differences between predicted and experimental power outputs and power output influenced by variations in regenerators are discussed. Technology work was conducted on heat-exchanger concepts to minimize the number of joints as well as to enhance the heat transfer in the heater. Design parameters and conceptual design features are also presented for a 25 kWe, single-cylinder free-piston Stirling space power converter. Projections are made for future space power requirements over the next few decades along with a recommendation to consider the use of dynamic power conversion systems, either solar or nuclear. A cursory comparison is presented showing the mass benefits of a Stirling system over a Brayton system for the same peak temperature and output power. A description of a study to investigate the feasibility of scaling a single-cylinder free-piston Stirling space power module to the 150 kWe power range is presented.

SSME alternate turbopump (pump section) axial load analysis

NASA Technical Reports Server (NTRS)

Crease, G. A.; Rosello, A., Jr.; Fetfatsidis, A. K.

1989-01-01

A flow balancing computer program constructed to calculate the axial loads on the Space Shuttle Main Engine (SSME) alternate turbopumps (ATs) pump sections are described. The loads are used in turn to determine load balancing piston design requirements. The application of the program to the inlet section, inducer/impeller/stage, bearings, seals, labyrinth, damper, piston, face and corner, and stationary/rotating surfaces is indicated. Design analysis results are reported which show that the balancing piston's designs are adequate and that performance and life will not be degraded by the turbopump's axial load characteristics.

Automotive Stirling Engine Development Program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Richey, A.; Farrell, R.; Riecke, G.; Ernst, W.; Howarth, R.; Cronin, M.; Simetkosky, M.; Smith, G.; Meacher, J.

1985-01-01

Development test activities on Mod I engines directed toward evaluating technologies for potential inclusion in the Mod II engine are summarized. Activities covered include: test of a 12-tube combustion gas recirculation combustor; manufacture and flow-distribution test of a two-manifold annular heater head; piston rod/piston base joint; single-solid piston rings; and a digital air/fuel concept. Also summarized are results of a formal assessment of candidate technologies for the Mod II engine, and preliminary design work for the Mod II. The overall program philosophy weight is outlined, and data and test results are presented.

Detection of Damage in Hydraulic Components by Acoustic Emission Techniques.

DTIC Science & Technology

1984-04-01

49 ".-4.- Vane Pumps 50 Piston Pumps 61 Gear Pumps 66 VI FIELD TESTS (GEAR PUMPS) 108 Pump Cavitation 108 Internal Mechanical Damage Test Procedure...with Bad Bearing 60 5.6 a Frequency Spectrum (0-100 KHz) of Piston Pump. Cavitation Test, Inlet Pressure =1.55 atm (Normal) 63 5.6 b Frequency Spectrum...0-100 KHz) of Piston Pump. Cavitation Test, Inlet Pressure =1.38 atm (Incipient) 64. vi i . .e 0" S.. j~ * .’ *"-.i’.-..N.?.. .. ° .,LIST OF FIGURES

On the dynamic response of pressure transmission lines in the research of helium-charged free piston Stirling engines

NASA Technical Reports Server (NTRS)

Miller, Eric L.; Dudenhoefer, James E.

1989-01-01

The signal distortion inherent to pressure transmission lines in free-piston Stirling engine research is discussed. Based on results from classical analysis, guidelines are formulated to describe the dynamic response properties of a volume-terminated transmission tube for applications involving the helium-charged free-piston Stirling engines. The underdamped flow regime is described, the primary resonance frequency is derived, and the pressure phase and amplitude distortion are discussed. The scope and limitation of the dynamic response analysis are considered.

Simulation of electrowetting lens and prism arrays for wavefront compensation.

PubMed

Gopinath, Juliet T; Bright, Victor M; Cogswell, Carol C; Niederriter, Robert D; Watson, Alexander; Zahreddine, Ramzi; Cormack, Robert H

2012-09-20

A novel application of electrowetting devices has been simulated: wavefront correction using an array of electrowetting lenses and prisms. Five waves of distortion can be corrected with Strehl ratios of 0.9 or higher, utilizing piston, tip-tilt, and curvature corrections from arrays of 19 elements and fill factors as low as 40%. Effective control of piston can be achieved by placing the liquid lens array at the focus of two microlens arrays. Seven waves of piston delay can be generated with variation in focal length between 1.5 and 500 mm.

Compression of helium to high pressures and temperatures using a ballistic piston apparatus

NASA Technical Reports Server (NTRS)

Roman, B. P.; Rovel, G. P.; Lewis, M. J.

1971-01-01

Some preliminary experiments are described which were carried out in a high enthalpy laboratory to investigate the compression of helium, a typical shock-tube driver gas, to very high pressures and temperatures by means of a ballistic piston. The purpose of these measurements was to identify any problem areas in the compression process, to determine the importance of real gas effects duDC 47355s process, and to establish the feasibility of using a ballistic piston apparatus to achieve temperatures in helium in excess of 10,000 K.

CONTROL ROD DRIVE

DOEpatents

Chapellier, R.A.; Rogers, I.

1961-06-27

Accurate and controlled drive for the control rod is from an electric motor. A hydraulic arrangement is provided to balance a piston against which a control rod is urged by the application of fluid pressure. The electric motor drive of the control rod for normal operation is made through the aforementioned piston. In the event scramming is required, the fluid pressure urging the control rod against the piston is relieved and an opposite fluid pressure is applied. The lack of mechanical connection between the electric motor and control rod facilitates the scramming operation.

Benefit from NASA

NASA Image and Video Library

2004-04-22

NASA structural materials engineer, Jonathan Lee, displays blocks and pistons as examples of some of the uses for NASA’s patented high-strength aluminum alloy originally developed at Marshall Space Flight Center in Huntsville, Alabama. NASA desired an alloy for aerospace applications with higher strength and wear-resistance at elevated temperatures. The alloy is a solution to reduce costs of aluminum engine pistons and lower engine emissions for the automobile industry. The Boats and Outboard Engines Division at Bombardier Recreational Products of Sturtevant, Wisconsin is using the alloy for pistons in its Evinrude E-Tec outboard engine line.

Free piston space Stirling technology program

NASA Technical Reports Server (NTRS)

Dochat, G. R.; Dhar, M.

1989-01-01

MTI recently completed an initial technology feasibility program for NASA by designing, fabricating and testing a space power demonstrator engine (SPDE). This program, which confirms the potential of free-piston Stirling engines, provided the major impetus to initiate a free-piston Stirling space engine (SSE) technology program. The accomplishments of the SPDE program are reviewed, and an overview of the SSE technology program and technical status to date is provided. It is shown that progress in both programs continues to justify its potential for either nuclear or solar space power missions.

Surface controlled blade stabilizer

DOEpatents

Russell, Larry R.

1983-01-01

Drill string stabilizer apparatus, controllable to expand and retract entirely from the surface by control of drill string pressure, wherein increase of drill string pressure from the surface closes a valve to create a piston means which is moved down by drill string pressure to expand the stabilizer blades, said valve being opened and the piston moving upward upon reduction of drill string pressure to retract the stabilizer blades. Upward and downward movements of the piston and an actuator sleeve therebelow are controlled by a barrel cam acting between the housing and the actuator sleeve.

Effects of intravenous delivery systems on infused red blood cells.

PubMed

Gibson, J S; Leff, R D; Roberts, R J

1984-03-01

The effects of various intravenous delivery systems on the integrity of infused red blood cells (RBCs) were studied. Using a factorial design, whole blood and packed RBCs were infused through i.v. delivery systems employing various combinations of i.v. tubing diameter and length, needle gauge, infusion rate (5 and 50 ml/hr), type of infusion pump (piston, diaphragm, or peristaltic operation), and type of blood product. The age and temperature of the blood filter used were held constant. A 5-ml sample of the blood product obtained during each experimental run was analyzed for plasma free-hemoglobin to assess the degree of hemolysis. Osmotic fragility of the RBCs was evaluated by measuring the percentage of hemolysis in the blood products in various concentrations of sodium chloride solution. Type of blood product and i.v. pump were the only variables significantly influencing RBC hemolysis. In both blood products, a greater degree of hemolysis occurred with the peristaltic-type pump than with the other types of pumps. In packed RBCs, the diaphragm-type pump produced greater hemolysis than the piston-type pump, but hemolysis was similar in whole-blood samples. Regardless of the type of pump, more hemolysis occurred in whole blood at the 5-ml/hr infusion rate than at the 50-ml/hr rate, but the converse was true in packed RBCs. Samples of both blood products were less osmotically fragile than their respective controls at sodium chloride concentrations ranging from 0.30 to 0.50%.(ABSTRACT TRUNCATED AT 250 WORDS)

Air-Bearing-Piston Suspension System

NASA Technical Reports Server (NTRS)

Mullen, Donald; Bishop, Stephen J.

1992-01-01

Suspension system based on air-bearing piston holds up steel ball against gravitation while allowing ball to translate vertically and rotate freely. System designed to simulate effect of microgravity on ball. Applicable to suppression of vibrations and delicate machining processes.

A linear motor and compact cylinder-piston driver for left ventricular bypass.

PubMed

Qian, K X

1990-01-01

A simple, portable, reliable and noise-free pneumatic driver has been developed. It consists of a linear motor attached to a cylinder piston, in one unit. The motor coil is directly wound on the cylinder, and the permanent magnet is fixed to the piston. As a continuous voltage square wave is applied to the coil, the cylinder reciprocates on the piston periodically, producing air pressure and vacuum alternately. In conjunction with a locally made diaphragm pump, the driver was tested in vitro and in vivo. Results demonstrated that the device could drive the diaphragm pump and so support the circulation of an experimental animal. The driver weighs 12 kg. For 200 mmHg air pressure and -80 mmHg vacuum the power consumed is 30 W. Its noise is about 30 dB, less than that of an artificial valve and pump.

Final design of a free-piston hydraulic advanced Stirling conversion system

NASA Technical Reports Server (NTRS)

Wallace, D. A.; Noble, J. E.; Emigh, S. G.; Ross, B. A.; Lehmann, G. A.

1991-01-01

Under the US Department of Energy's (DOEs) Solar Thermal Technology Program, Sandia National Laboratories is evaluating heat engines for solar distributed receiver systems. The final design is described of an engineering prototype advanced Stirling conversion system (ASCS) with a free-piston hydraulic engine output capable of delivering about 25 kW of electric power to a utility grid. The free-piston Stirling engine has the potential for a highly reliable engine with long life because it has only a few moving parts, has noncontacting bearings, and can be hermetically sealed. The ASCS is designed to deliver maximum power per year over a range of solar input with a design life of 30 years (60,000 h). The system includes a liquid Nak pool boiler heat transport system and a free-piston Stirling engine with high-pressure hydraulic output, coupled with a bent axis variable displacement hydraulic motor and a rotary induction generator.

Measurement of Work Generation and Improvement in Performance of a Pulse Tube Engine

NASA Astrophysics Data System (ADS)

Hamaguchi, Kazuhiro; Futagi, Hiroaki; Yazaki, Taichi; Hiratsuka, Yoshikatsu

Apart from double acting type engines, Stirling engines have either 2 pistons in 2 cylinders or 2 pistons in a single cylinder. Typically, the heater, regenerator and cooler are installed between the 2 pistons. The pulse tube engine, on the other hand, consists of a single piston in a single cylinder, a pulse tube, a heater, a regenerator, a cooler and a second cooler. For this paper, a simple prototype engine that uses air at normal atmospheric pressure as the working gas was fabricated. The oscillating velocity of the working gas in the pulse tube was measured using LDV, and the work flow emitting out of the pulse tube was observed. In addition, the effect of inserting heat storage material in the pulse tube on shaft power and indicated power was examined experimentally. A dramatic increase in the shaft power was achieved.

A comparative approach for the characterization of a pneumatic piston gauge up to 8 MPa using finite element calculations

NASA Astrophysics Data System (ADS)

Dogra, Sugandha; Singh, Jasveer; Lodh, Abhishek; Dilawar Sharma, Nita; Bandyopadhyay, A. K.

2011-02-01

This paper reports the behavior of a well-characterized pneumatic piston gauge in the pressure range up to 8 MPa through simulation using finite element method (FEM). Experimentally, the effective area of this piston gauge has been estimated by cross-floating to obtain A0 and λ. The FEM technique addresses this problem through simulation and optimization with standard commercial software (ANSYS) where the material properties of the piston and cylinder, dimensional measurements, etc are used as the input parameters. The simulation provides the effective area Ap as a function of pressure in the free deformation mode. From these data, one can estimate Ap versus pressure and thereby Ao and λ. Further, we have carried out a similar theoretical calculation of Ap using the conventional method involving the Dadson's as well as Johnson-Newhall equations. A comparison of these results with the experimental results has been carried out.

Ducted combustion chamber for direct injection engines and method

DOEpatents

Mueller, Charles

2015-03-03

An internal combustion engine includes an engine block having a cylinder bore and a cylinder head having a flame deck surface disposed at one end of the cylinder bore. A piston connected to a rotatable crankshaft and configured to reciprocate within the cylinder bore has a piston crown portion facing the flame deck surface such that a combustion chamber is defined within the cylinder bore and between the piston crown and the flame deck surface. A fuel injector having a nozzle tip disposed in fluid communication with the combustion chamber has at least one nozzle opening configured to inject a fuel jet into the combustion chamber along a fuel jet centerline. At least one duct defined in the combustion chamber between the piston crown and the flame deck surface has a generally rectangular cross section and extends in a radial direction relative to the cylinder bore substantially along the fuel jet centerline.

Performance analysis on free-piston Stirling cryocooler based on an idealized mathematical model

NASA Astrophysics Data System (ADS)

Guo, Y. X.; Chao, Y. J.; Gan, Z. H.; Li, S. Z.; Wang, B.

2017-12-01

Free-piston Stirling cryocoolers have extensive applications for its simplicity in structure and decrease in mass. However, the elimination of the motor and the crankshaft has made its thermodynamic characteristic different from that of Stirling cryocoolers with displacer driving mechanism. Therefore, an idealized mathematical model has been established, and with this model, an attempt has been made to analyse the thermodynamic characteristic and the performance of free-piston Stirling cryocooler. To certify this mathematical model, a comparison has been made between the model and a numerical model. This study reveals that due to the displacer damping force necessary for the production of cooling capacity, the free-piston Stirling cryocooler is inherently less efficient than Stirling cryocooler with displacer driving mechanism. Viscous flow resistance and incomplete heat transfer in the regenerator are the two major causes of the discrepancy between the results of the idealized mathematical model and the numerical model.

Final design of a free-piston hydraulic advanced Stirling conversion system

NASA Astrophysics Data System (ADS)

Wallace, D. A.; Noble, J. E.; Emigh, S. G.; Ross, B. A.; Lehmann, G. A.

Under the US Department of Energy's (DOEs) Solar Thermal Technology Program, Sandia National Laboratories is evaluating heat engines for solar distributed receiver systems. The final design is described of an engineering prototype advanced Stirling conversion system (ASCS) with a free-piston hydraulic engine output capable of delivering about 25 kW of electric power to a utility grid. The free-piston Stirling engine has the potential for a highly reliable engine with long life because it has only a few moving parts, has noncontacting bearings, and can be hermetically sealed. The ASCS is designed to deliver maximum power per year over a range of solar input with a design life of 30 years (60,000 h). The system includes a liquid Nak pool boiler heat transport system and a free-piston Stirling engine with high-pressure hydraulic output, coupled with a bent axis variable displacement hydraulic motor and a rotary induction generator.

Inductance position sensor for pneumatic cylinder

NASA Astrophysics Data System (ADS)

Ripka, Pavel; Chirtsov, Andrey; Mirzaei, Mehran; Vyhnanek, Jan

2018-04-01

The position of the piston in pneumatic cylinder with aluminum wall can be measured by external inductance sensor without modifications of the aluminum piston and massive iron piston rod. For frequencies below 20 Hz the inductance is increasing with inserting rod due to the rod permeability. This mode has disadvantage of slow response to piston movement and also high temperature sensitivity. At the frequency of 45 Hz the inductance is position independent, as the permeability effect is compensated by the eddy current effect. At higher frequencies eddy current effects in the rod prevail, the inductance is decreasing with inserting rod. In this mode the sensitivity is smaller but the sensor response is fast and temperature stability is better. We show that FEM simulation of this sensor using measured material properties gives accurate results, which is important for the sensor optimization such as designing the winding geometry for the best linearity.

Apparatus for the conversion of power strokes of a random sequence and of random lengths of strokes into potential energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elkuch, E.

1984-01-17

The apparatus comprises at least one positive displacement pump, which is driven by the sea waves. The quantity of delivery of this pump is adjustable in accordance with the lengths of strokes made by the ocean waves. This is made possible in that the positive displacement pump comprises pistons having different volume displacements. The height of the incoming waves is measured by a membrane box connected to a transducer which generates signals such that only that piston of the plurality of pistons is made to operate, which has by design a volume displacement which gives the optimal recovery of themore » energy of the ocean waves. The or these pistons pump a working fluid into a storage vessel, which allows the generation of peak load as well as base load electrical energy.« less

Heat-machine control by quantum-state preparation: from quantum engines to refrigerators.

PubMed

Gelbwaser-Klimovsky, D; Kurizki, G

2014-08-01

We explore the dependence of the performance bounds of heat engines and refrigerators on the initial quantum state and the subsequent evolution of their piston, modeled by a quantized harmonic oscillator. Our goal is to provide a fully quantized treatment of self-contained (autonomous) heat machines, as opposed to their prevailing semiclassical description that consists of a quantum system alternately coupled to a hot or a cold heat bath and parametrically driven by a classical time-dependent piston or field. Here, by contrast, there is no external time-dependent driving. Instead, the evolution is caused by the stationary simultaneous interaction of two heat baths (having distinct spectra and temperatures) with a single two-level system that is in turn coupled to the quantum piston. The fully quantized treatment we put forward allows us to investigate work extraction and refrigeration by the tools of quantum-optical amplifier and dissipation theory, particularly, by the analysis of amplified or dissipated phase-plane quasiprobability distributions. Our main insight is that quantum states may be thermodynamic resources and can provide a powerful handle, or control, on the efficiency of the heat machine. In particular, a piston initialized in a coherent state can cause the engine to produce work at an efficiency above the Carnot bound in the linear amplification regime. In the refrigeration regime, the coefficient of performance can transgress the Carnot bound if the piston is initialized in a Fock state. The piston may be realized by a vibrational mode, as in nanomechanical setups, or an electromagnetic field mode, as in cavity-based scenarios.

Heat-machine control by quantum-state preparation: From quantum engines to refrigerators

NASA Astrophysics Data System (ADS)

Gelbwaser-Klimovsky, D.; Kurizki, G.

2014-08-01

We explore the dependence of the performance bounds of heat engines and refrigerators on the initial quantum state and the subsequent evolution of their piston, modeled by a quantized harmonic oscillator. Our goal is to provide a fully quantized treatment of self-contained (autonomous) heat machines, as opposed to their prevailing semiclassical description that consists of a quantum system alternately coupled to a hot or a cold heat bath and parametrically driven by a classical time-dependent piston or field. Here, by contrast, there is no external time-dependent driving. Instead, the evolution is caused by the stationary simultaneous interaction of two heat baths (having distinct spectra and temperatures) with a single two-level system that is in turn coupled to the quantum piston. The fully quantized treatment we put forward allows us to investigate work extraction and refrigeration by the tools of quantum-optical amplifier and dissipation theory, particularly, by the analysis of amplified or dissipated phase-plane quasiprobability distributions. Our main insight is that quantum states may be thermodynamic resources and can provide a powerful handle, or control, on the efficiency of the heat machine. In particular, a piston initialized in a coherent state can cause the engine to produce work at an efficiency above the Carnot bound in the linear amplification regime. In the refrigeration regime, the coefficient of performance can transgress the Carnot bound if the piston is initialized in a Fock state. The piston may be realized by a vibrational mode, as in nanomechanical setups, or an electromagnetic field mode, as in cavity-based scenarios.