13. FLOOR 1: DETAIL OF POSTS SUPPORTING BRIDGE TREE TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. FLOOR 1: DETAIL OF POSTS SUPPORTING BRIDGE TREE TO NORTH; NOTE BEADING AT CORNERS; WEDGES ADJUST HEIGHT OF PIVOTING END OF BRIDGE TREE - Pantigo Windmill, James Lane, East Hampton, Suffolk County, NY

Estimation of optimal pivot point for remote center of motion alignment in surgery.

PubMed

Rosa, Benoît; Gruijthuijsen, Caspar; Van Cleynenbreugel, Ben; Sloten, Jos Vander; Reynaerts, Dominiek; Poorten, Emmanuel Vander

2015-02-01

The determination of an optimal pivot point ([Formula: see text]) is important for instrument manipulation in minimally invasive surgery. Such knowledge is of particular importance for robotic-assisted surgery where robots need to rotate precisely around a specific point in space in order to minimize trauma to the body wall while maintaining position control. Remote center of motion (RCM) mechanisms are commonly used, where the RCM point is manually and visually aligned. If not positioned appropriately, this misalignment might lead to intolerably high forces on the body wall with increased risk of postoperative complications or instrument damage. An automated method to align the RCM with the [Formula: see text] was developed and tested. Computer vision and a lightweight calibration procedure are used to estimate the optimal pivot point. One or two pre-calibrated cameras viewing the surgical scene are employed. The surgeon is asked to make short pivoting movements, applying as little torque as possible, with an instrument of choice passing through the insertion point while camera images are being recorded. The physical properties of an instrument rotating around a pivot point are exploited in a random sample consensus scheme to robustly estimate the ideal position of the RCM in the image planes. Triangulation is used to estimate the RCM position in 3D. Experiments were performed on a specially designed mockup to test the method. The position of the pivot point is estimated with an average error less than 1.85 mm using two webcams placed from approximately 30 cm to 1 m away from the scene. The entire procedure was completed in a few seconds. In automated method to estimate the ideal position of the RCM was shown to be reliable. The method can be implemented within a visual servoing approach to automatically place the RCM point, or the results can be displayed on a screen to provide guidance to the surgeon. Further work includes the development of an image-guided alignment method and validation with in vivo experiments.

Focus collimator press for a collimator for gamma ray cameras

DOE Office of Scientific and Technical Information (OSTI.GOV)

York, R.N.; York, D.L.

A focus collimator press for collimators for gamma ray cameras is described comprising a pivot arm of fixed length mounted on a travelling pivot which is movable in the plane of a spaced apart work table surface in a direction toward and away from the work table. A press plate is carried at the opposite end of the fixed length pivot arm, and is maintained in registration with the same portion of the work table for pressing engagement with each undulating radiation opaque strip as it is added to the top of a collimator stack in process by movement ofmore » the travelling pivot inward toward the work table. This enables the press plate to maintain its relative position above the collimator stack and at the same time the angle of the press plate changes, becoming less acute in relation to the work table as the travelling pivot motes inwardly toward the work table. The fixed length of the pivot arm is substantially equal to the focal point of the converging apertures formed by each pair of undulating strips stacked together. Thus, the focal point of each aperture row falls substantially on the axis of the travelling pivot, and since it moves in the plane of the work table surface the focal point of each aperture row is directed to lie in the same common plane. When one of two collimator stacks made in this way is rotated 180 degrees and the two bonded together along their respective first strips, all focal points of every aperture row lie on the central axis of the completed collimator.« less

Differences in anthropometric characteristics in relation to throwing velocity and competitive level in professional male team handball: a tool for talent profiling.

PubMed

Fieseler, Georg; Hermassi, Souhail; Hoffmeyer, Birgit; Schulze, Stephan; Irlenbusch, Lars; Bartels, Thomas; Delank, Karl-Stefan; Laudner, Kevin G; Schwesig, René

2017-01-01

The primary aim of the study was to examine the anthropometric characteristics as well as throwing and sprinting performance of professional handball players classified by playing position and competition level. 21 male players (age: 25.2±5.1 years) from the first German handball league (FGL) and 34 male players (age: 26.1±4.1 years) from the third German handball league (TGL) were categorized as backs, pivots, wings and goalkeepers. Measurements included anthropometric data (height, mass and body mass index (BMI)), throwing and sprinting performance selected out of a complex handball test (HBCT), which was conducted twice (2 rounds). During the HBCT, the subjects performed two sprints (10, 20 m), two standing throws with run-up (ST) and four vertical jump throws (VJT) over a hurdle (20 cm) with and without precision for goal shot. The anthropometric data revealed a significantly (P=0.038 and η2=0.079) shorter body height for TGL than for FGL players. In the cohort of first league athletes the pivots were the tallest (1.98±0.04 m), backs in the third league showed the maximum body height (1.90±0.05 m). Regarding body mass, pivots were the heaviest players independent from the league membership. The FGL players showed a significantly (P<0.05 and η2>0.10) higher throwing velocity in all type of throws. Body height was significantly related to ST (r=0.53) and VJT (r=0.52) in the first round of HBCT but only for the FGL athletes. Throwing velocity was also correlated with BMI (r=-0.50) among the TGL players. Substantial differences of body characteristics, throwing and sprinting performance between playing positions and competitive levels underline the importance of a careful scouting and position-specific training for professional handball players.

Simulator scene display evaluation device

NASA Technical Reports Server (NTRS)

Haines, R. F. (Inventor)

1986-01-01

An apparatus for aligning and calibrating scene displays in an aircraft simulator has a base on which all of the instruments for the aligning and calibrating are mounted. Laser directs beam at double right prism which is attached to pivoting support on base. The pivot point of the prism is located at the design eye point (DEP) of simulator during the aligning and calibrating. The objective lens in the base is movable on a track to follow the laser beam at different angles within the field of vision at the DEP. An eyepiece and a precision diopter are movable into a position behind the prism during the scene evaluation. A photometer or illuminometer is pivotable about the pivot into and out of position behind the eyepiece.

18. Detail view of central pivot pier, drive gear rack, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

18. Detail view of central pivot pier, drive gear rack, and stabilizing wheel, looking southwest - India Point Railroad Bridge, Spanning Seekonk River between Providence & East Providence, Providence, Providence County, RI

Plant responses, climate pivot points, and trade-offs in water-limited ecosystems

USGS Publications Warehouse

Munson, Seth M.

2013-01-01

Plant species in dryland ecosystems are limited by water availability and may be vulnerable to increases in aridity. Methods are needed to monitor and assess the rate of change in plant abundance and composition in relation to climate, understand the potential for degradation in dryland ecosystems, and forecast future changes in plant species assemblages. I employ nearly a century of vegetation monitoring data from three North American deserts to demonstrate an approach to determine plant species responses to climate and critical points over a range of climatic conditions at which plant species shift from increases to decreases in abundance (climate pivot points). I assess these metrics from a site to regional scale and highlight how these indicators of plant performance can be modified by the physical and biotic environment. For example, shrubs were more responsive to drought and high temperatures on shallow soils with limited capacity to store water and fine-textured soils with slow percolation rates, whereas perennial grasses were more responsive to precipitation in sparse shrublands than in relatively dense grasslands and shrublands, where competition for water is likely more intense. The responses and associated climate pivot points of plant species aligned with their lifespan and structural characteristics, and the relationship between responses and climate pivot points provides evidence of the trade-off between the capacity of a plant species to increase in abundance when water is available and its drought resistance.

Clinical Outcome of Medial Pivot Compared With Press-Fit Condylar Sigma Cruciate-Retaining Mobile-Bearing Total Knee Arthroplasty.

PubMed

Kim, Young-Hoo; Park, Jang-Won; Kim, Jun-Shik

2017-10-01

The purpose of this study was to compare the long-term clinical results, radiographic results, range of knee motion, patient satisfaction, and the survival rate of Medial-Pivot posterior cruciate-substituting, knee prosthesis and a press-fit condylar (PFC) Sigma cruciate-retaining mobile-bearing knee prosthesis in the same patients. One hundred eighty-two patients received Medial-Pivot knee prosthesis in one knee and a PFC Sigma knee prosthesis in the contralateral knee. The minimum duration of follow-up was 11 years (range, 11-12.6 years). The knees with a Medial-Pivot knee prosthesis had significantly worse results than those with a PFC Sigma knee prosthesis at the final follow-up with regard to the mean postoperative Knee Society knee scores (90 compared with 95 points), Western Ontario and McMaster Universities Osteoarthritis Index score (25 compared with 18 points), and range of knee motion (117° compared with 128°). Patients were more satisfied with PFC Sigma knee prosthesis (93%) than with Medial-Pivot knee prosthesis (75%). Complication rates were significantly higher in the Medial-Pivot knee group (26%) than those in the PFC Sigma knee group (6.5%). Radiographic results and survival rates (99% compared with 99.5%) were similar between the 2 groups. Although the long-term fixation and survival rate of both Medial-Pivot and PFC Sigma prostheses were similar, we observed a worse knee score, worse range of knee motion, and patient satisfaction was less in the Medial-Pivot knee group than in the PFC Sigma knee group. Furthermore, complication rate was also higher in the Medial-Pivot knee group than the other group. Copyright © 2017 Elsevier Inc. All rights reserved.

Serb Guardrail : South Ashland Interchange California State Line Section Pacific Highway (Interstate 5) Jackson County, Oregon : final report.

DOT National Transportation Integrated Search

1997-02-01

The Self Restoring Barrier (SERB) is a proprietary guardrail unit comprised of a single tubular thrie beam held outward from the supporting wooden posts by pivoting metal arms, its height above the ground secured by short cables attached to the top o...

Do position and size matter? An analysis of cage and placement variables for optimum lordosis in PLIF reconstruction.

PubMed

Landham, Priyan R; Don, Angus S; Robertson, Peter A

2017-11-01

To examine monosegmental lordosis after posterior lumbar interbody fusion (PLIF) surgery and relate lordosis to cage size, shape, and placement. Eighty-three consecutive patients underwent single-level PLIF with paired identical lordotic cages involving a wide decompression and bilateral facetectomies. Cage parameters relating to size (height, lordosis, and length) and placement (expressed as a ratio relative to the length of the inferior vertebral endplate) were recorded. Centre point ratio (CPR) was the distance to the centre of both cages and indicated mean position of both cages. Posterior gap ratio (PGR) was the distance to the most posterior cage and indicated position and cage length indirectly. Relationships between lordosis and cage parameters were explored. Mean lordosis increased by 5.98° (SD 6.86°). The cages used varied in length from 20 to 27 mm, in lordosis from 10° to 18°, and in anterior cage height from 10 to 17 mm. The mean cage placement as determined by CPR was 0.54 and by PGR was 0.16. The significant correlations were: both CPR and PGR with lordosis gain at surgery (r = 0.597 and 0.537, respectively, p < 0.001 both), cage lordosis with the final lordosis (r = 0.234, p < 0.05), and anterior cage height was negatively correlated with a change in lordosis (r = -0.297, p < 0.01). Cage size, shape, and position, in addition to surgical technique, determine lordosis during PLIF surgery. Anterior placement with sufficient "clear space" behind the cages is recommended. In addition, cages should be of moderate height and length, so that they act as an effective pivot for lordosis.

The Trapezius Muscle Flap: A Viable Alternative for Posterior Scalp and Neck Reconstruction.

PubMed

Yang, Hee Jun; Lee, Dong Hun; Kim, Yang Woo; Lee, Sang Gu; Cheon, Young Woo

2016-11-01

The trapezius muscle flap is not usually the first reconstructive option for skin and soft tissue defects in the posterior neck and scalp due to surgeons' unfamiliarity with the surgical anatomy and developments in free tissue transfer techniques. The goals of this study were to describe the clinical use of trapezius flaps in posterior neck and scalp reconstruction, and to investigate the vascular anatomy of trapezius flaps in Asians in order to obtain information facilitating the safe design and elevation of flaps in which most of the muscle is preserved. A retrospective chart review was performed of 10 patients who underwent trapezius muscle flap for posterior neck and scalp defects. We also performed an anatomical study of 16 flaps harvested from 8 preserved Asian adult cadavers and evaluated the main landmarks relevant for trapezius muscle flap. In the anatomical study, the mean vertical height from the inferior angle of the scapula to the point at which the superficial cervical artery penetrated the trapezius was 4.31±2.14 cm. The mean vertical height of the trapezius muscle flap pivot point was 9.53±2.08 cm from the external occipital protuberance. Among the 10 flaps, partial necrosis on the overlaid skin graft occurred in 1 patient and postoperative seroma occurred in another patient. Vascular variations in the trapezius muscle flap are uncommon in Asians, but when present, such variations appear to have little impact on harvesting the flap or on its circulation. The trapezius muscle flap is a viable alternative for posterior neck and scalp reconstruction.

The Trapezius Muscle Flap: A Viable Alternative for Posterior Scalp and Neck Reconstruction

PubMed Central

Yang, Hee Jun; Kim, Yang Woo; Lee, Sang Gu

2016-01-01

Background The trapezius muscle flap is not usually the first reconstructive option for skin and soft tissue defects in the posterior neck and scalp due to surgeons' unfamiliarity with the surgical anatomy and developments in free tissue transfer techniques. The goals of this study were to describe the clinical use of trapezius flaps in posterior neck and scalp reconstruction, and to investigate the vascular anatomy of trapezius flaps in Asians in order to obtain information facilitating the safe design and elevation of flaps in which most of the muscle is preserved. Methods A retrospective chart review was performed of 10 patients who underwent trapezius muscle flap for posterior neck and scalp defects. We also performed an anatomical study of 16 flaps harvested from 8 preserved Asian adult cadavers and evaluated the main landmarks relevant for trapezius muscle flap. Results In the anatomical study, the mean vertical height from the inferior angle of the scapula to the point at which the superficial cervical artery penetrated the trapezius was 4.31±2.14 cm. The mean vertical height of the trapezius muscle flap pivot point was 9.53±2.08 cm from the external occipital protuberance. Among the 10 flaps, partial necrosis on the overlaid skin graft occurred in 1 patient and postoperative seroma occurred in another patient. Conclusions Vascular variations in the trapezius muscle flap are uncommon in Asians, but when present, such variations appear to have little impact on harvesting the flap or on its circulation. The trapezius muscle flap is a viable alternative for posterior neck and scalp reconstruction. PMID:27896183

Estimating vehicle height using homographic projections

DOEpatents

Cunningham, Mark F; Fabris, Lorenzo; Gee, Timothy F; Ghebretati, Jr., Frezghi H; Goddard, James S; Karnowski, Thomas P; Ziock, Klaus-peter

2013-07-16

Multiple homography transformations corresponding to different heights are generated in the field of view. A group of salient points within a common estimated height range is identified in a time series of video images of a moving object. Inter-salient point distances are measured for the group of salient points under the multiple homography transformations corresponding to the different heights. Variations in the inter-salient point distances under the multiple homography transformations are compared. The height of the group of salient points is estimated to be the height corresponding to the homography transformation that minimizes the variations.

Pivots for pointing: visually-monitored pointing has higher arm elevations than pointing blindfolded.

PubMed

Wnuczko, Marta; Kennedy, John M

2011-10-01

Observers pointing to a target viewed directly may elevate their fingertip close to the line of sight. However, pointing blindfolded, after viewing the target, they may pivot lower, from the shoulder, aligning the arm with the target as if reaching to the target. Indeed, in Experiment 1 participants elevated their arms more in visually monitored than blindfolded pointing. In Experiment 2, pointing to a visible target they elevated a short pointer more than a long one, raising its tip to the line of sight. In Experiment 3, the Experimenter aligned the participant's arm with the target. Participants judged they were pointing below a visually monitored target. In Experiment 4, participants viewing another person pointing, eyes-open or eyes-closed, judged the target was aligned with the pointing arm. In Experiment 5, participants viewed their arm and the target via a mirror and posed their arm so that it was aligned with the target. Arm elevation was higher in pointing directly.

A 3-point derivation of dominant tree height equations

Treesearch

Don C. Bragg

2011-01-01

This paper describes a new approach for deriving height-diameter (H-D) equations from limited information and a few assumptions about tree height. Only three data points are required to fit this model, which can be based on virtually any nonlinear function. These points are the height of a tree at diameter at breast height (d.b.h.), the predicted height of a 10-inch d....

More About The Farley Three-Dimensional Braider

NASA Technical Reports Server (NTRS)

Farley, Gary L.

1993-01-01

Farley three-dimensional braider, undergoing development, is machine for automatic fabrication of three-dimensional braided structures. Incorporates yarns into structure at arbitrary braid angles to produce complicated shape. Braiding surface includes movable braiding segments containing pivot points, along which yarn carriers travel during braiding process. Yarn carrier travels along sequence of pivot points as braiding segments move. Combined motions position yarns for braiding onto preform. Intended for use in making fiber preforms for fiber/matrix composite parts, such as multiblade propellers. Machine also described in "Farley Three-Dimensional Braiding Machine" (LAR-13911).

An antithetic variate to facilitate upper-stem height measurements for critical height sampling with importance sampling

Treesearch

Thomas B. Lynch; Jeffrey H. Gove

2013-01-01

Critical height sampling (CHS) estimates cubic volume per unit area by multiplying the sum of critical heights measured on trees tallied in a horizontal point sample (HPS) by the HPS basal area factor. One of the barriers to practical application of CHS is the fact that trees near the field location of the point-sampling sample point have critical heights that occur...

Three-point spherical mirror mount

DOEpatents

Cutburth, Ronald W.

1990-01-01

A three-point spherical mirror mount for use with lasers is disclosed. The improved mirror mount is adapted to provide a pivot ring having an outer surface with at least three spaced apart mating points to engage an inner spherical surface of a support housing.

Three-point spherical mirror mount

DOEpatents

Cutburth, R.W.

1984-01-23

A three-point spherical mirror mount for use with lasers is disclosed. The improved mirror mount is adapted to provide a pivot ring having an outer surface with at least three spaced apart mating points to engage an inner spherical surface of a support housing.

Balloon-borne 3-meter telescope for far-infrared and submillimeter astronomy

NASA Technical Reports Server (NTRS)

Fazio, G. G.

1986-01-01

The gimbal design was studied and revised to eliminate the alignment and limited rotation problems inherent in the flex-pivot design. A new design using ball-bearings to replace the flex-pivot was defined and its performance analyzed. An error analysis for the entire gondola pointing system was also prepared. Mirror development and the test program using mirror test blanks from Dornier were continued.

Balloon-borne three-meter telescope for far-infrared and submillimeter astronomy

NASA Technical Reports Server (NTRS)

Fazio, Giovanni G.

1986-01-01

The study and revision of the gimbal design of the Three-Meter Balloon Borne Telescope (TMBBT) is discussed. Efforts were made to eliminate the alignment and limited rotation problems inherent in the flex-pivot design. A new design using ball bearings to replace the flex-pivots was designed and its performance analyzed. An error analysis for the entire gondola pointing system was also prepared.

Variation in lung volumes and capacities among young males in relation to height.

PubMed

Bhatti, Urooj; Rani, Keenjher; Memon, Muhammad Qasim

2014-01-01

Vital Capacity (VC) is defined as a change in volume of lung after maximal inspiration followed by maximal expiration is called Vital Capacity of lungs. It is the sum of tidal volume, inspiratory reserve volume .and expiratory reserve volume. Vital capacity of normal adults ranges between 3 to 5 litres. A number of physiological factors like age, gender, height and ethnicity effect lung volumes. The reference values of lung volume and capacities were calculated previously and those studies played pivotal role in establishing the fact that air volume capacities measured in an individual fall within a wide range among healthy persons of same age, gender and height buit with different ethnicity. The objective of this study was to evaluate the changes in vital capacity in with height and gender. This cross-sectional study included 74 male students in the Department of Physiology, Liaquat University of Medical and Health Sciences, Jamshoro during January-March, 2014. The volunteers were divided into 2 groups of height ≤ 167.4 cm and > 167.4 cm. The volunteers' height was measured in cm. Vital capacity of the subjects was measured using standard protocol. Mean ± SD of age, height and vital capacity were calculated. Mean vital capacity in students with height > 167.4 cm was higher than average vital capacity of students with height ≤ 167.4 cm. It might be due to the increased surface area of the lungs in relation with increasing height. There are variations in vital capacity of individuals in relation to their heights, within the same ethnic and age groups.

Apparatus for mounting photovoltaic power generating systems on buildings

DOEpatents

Russell, Miles C [Lincoln, MA

2009-08-18

Rectangular photovoltaic (PV) modules are mounted on a building roof by mounting stands that are distributed in rows and columns. Each stand comprises a base plate and first and second different height brackets attached to opposite ends of the base plate. Each first and second bracket comprises two module-support members. One end of each module is pivotally attached to and supported by a first module-support member of a first bracket and a second module-support member of another first bracket. At its other end each module rests on but is connected by flexible tethers to module-support members of two different second brackets. The tethers are sized to allow the modules to pivot up away from the module-support members on which they rest to a substantially horizontal position in response to wind uplift forces.

Design charts for arbitrarily pivoted, liquid-lubricated flat-sector-pad thrust bearing

NASA Technical Reports Server (NTRS)

Etsion, I.

1977-01-01

A flat, sector-shaped geometry for a liquid-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. Results are presented in design charts that enable a direct approach to the design of point- and line-pivoted, tilting pad bearings. A comparison is made with the Mitchell bearing approximation and it is found that this approximation always overestimates load capacity.

Physical and physiological characteristics of male handball players: influence of playing position and competitive level.

PubMed

Haugen, Thomas A; Tønnessen, Espen; Seiler, Stephen

2016-01-01

The purpose of this study was to quantify differences in anthropometrical and physical characteristics according to playing position and competitive level in male elite handball. One hundred and seventy-six national team and 1st division players (age 23±4 years, body mass 89±11 kg, body height 188±5 cm) participated in the study. All participants were tested on throwing velocity, 20-meter sprint, countermovement jump, 3000-meter run, 1RM squat and bench press. Back players achieved higher throwing velocities compared to other positions. National team back players achieved higher velocities in set shots (9.4%, P<0.001, d=1.5) and jump shots (8.1%, P<0.001, d=1.5) than 1st division players. Wings sprinted faster than pivots (3.5%, P<0.001, d=1.2) and goalkeepers (5.4%, P<0.001, d=1.2). Wings jumped higher than pivots (13.0%, P<0.001, d=1.0) and goalkeepers (11.4%, P=0.003, d=0.9). National team back players ran faster than 1st division back players over 3000 meters (4.9%, P=0.011, d=0.7). Back players showed better relative strength in squat than pivots (12.1%, P=0.016, d=0.7). Wings had better relative strength in squat that pivots (17.4%, P=0.001, d=1.0) and goalkeepers (13.1%, P=0.016, d=0.8). Pivots were 8.9% stronger than wing players (P=0.044, d=0.7) in 1RM bench press. Varying on-court demands in handball are reflected by different physical and physiological characteristics across playing standard and positions. Physical conditioning of players should therefore be individualized and targeted to solve the position-dependent tasks during play.

Development of a high stability pointing mechanism for wide application

NASA Technical Reports Server (NTRS)

Brunnen, A. J. D.; Bentall, R. H.

1982-01-01

A recurrent requirement of spaceborne instruments and communications equipment is that of accurate pointing. This need is recognizable in such diverse applications as Star Sensor trimming, Momentum Wheel gimballing, in-orbit adjustment or alignment of equipment, inter-satellite communication and Antenna Pointing. A pointing mechanism of novel design having several advantages over the more conventional gimbal, centre-pivoted, or cross axis pointing concepts is described.

A Lidar Point Cloud Based Procedure for Vertical Canopy Structure Analysis And 3D Single Tree Modelling in Forest

PubMed Central

Wang, Yunsheng; Weinacker, Holger; Koch, Barbara

2008-01-01

A procedure for both vertical canopy structure analysis and 3D single tree modelling based on Lidar point cloud is presented in this paper. The whole area of research is segmented into small study cells by a raster net. For each cell, a normalized point cloud whose point heights represent the absolute heights of the ground objects is generated from the original Lidar raw point cloud. The main tree canopy layers and the height ranges of the layers are detected according to a statistical analysis of the height distribution probability of the normalized raw points. For the 3D modelling of individual trees, individual trees are detected and delineated not only from the top canopy layer but also from the sub canopy layer. The normalized points are resampled into a local voxel space. A series of horizontal 2D projection images at the different height levels are then generated respect to the voxel space. Tree crown regions are detected from the projection images. Individual trees are then extracted by means of a pre-order forest traversal process through all the tree crown regions at the different height levels. Finally, 3D tree crown models of the extracted individual trees are reconstructed. With further analyses on the 3D models of individual tree crowns, important parameters such as crown height range, crown volume and crown contours at the different height levels can be derived. PMID:27879916

[Study on origin of meridians and collaterals through pain relieving effect of muscle regions].

PubMed

Dong, Bao-Qiang; Li, Chun-Ri; Huang, Feng-Yun; Zhang, Shu-Jian; Xue, Li-Gong

2011-08-01

Through analysis on sequencing of meridians and their muscle regions, their pertaining organs, run ning courses, linking and indications described in Zubi Shiyimai (Eleven Meridian of Foot and Hand), Yinyang Shiyimai (Eleven Meridian of Yinyang), Lingshu: Jingmai (Miraculous Pivot: Meridian) and Lingshu: Jinjing (Miraculous Pivot: Muscle Meridian), it is found that most of the indications of acupuncture in ancient time are symptoms of the muscle regions. 62.59% points of the national standard acupoints location close to tender points of the muscle regions, which indicates that the origin of early acupoints are tender points along the running courses of the muscle regions. Thus, it is concluded that meridians and their muscle regions have the same origin, which provides new train of thinking for a better comprehension of origin of meridians and collaterals.

36 CFR § 910.61 - Height of development.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 3 2013-07-01 2012-07-01 true Height of development. § 910... PENNSYLVANIA AVENUE DEVELOPMENT AREA Glossary of Terms § 910.61 Height of development. Height of development means the vertical distance measured from a specified point at the curb level to the highest point of...

Effects of LiDAR point density, sampling size and height threshold on estimation accuracy of crop biophysical parameters.

PubMed

Luo, Shezhou; Chen, Jing M; Wang, Cheng; Xi, Xiaohuan; Zeng, Hongcheng; Peng, Dailiang; Li, Dong

2016-05-30

Vegetation leaf area index (LAI), height, and aboveground biomass are key biophysical parameters. Corn is an important and globally distributed crop, and reliable estimations of these parameters are essential for corn yield forecasting, health monitoring and ecosystem modeling. Light Detection and Ranging (LiDAR) is considered an effective technology for estimating vegetation biophysical parameters. However, the estimation accuracies of these parameters are affected by multiple factors. In this study, we first estimated corn LAI, height and biomass (R² = 0.80, 0.874 and 0.838, respectively) using the original LiDAR data (7.32 points/m²), and the results showed that LiDAR data could accurately estimate these biophysical parameters. Second, comprehensive research was conducted on the effects of LiDAR point density, sampling size and height threshold on the estimation accuracy of LAI, height and biomass. Our findings indicated that LiDAR point density had an important effect on the estimation accuracy for vegetation biophysical parameters, however, high point density did not always produce highly accurate estimates, and reduced point density could deliver reasonable estimation results. Furthermore, the results showed that sampling size and height threshold were additional key factors that affect the estimation accuracy of biophysical parameters. Therefore, the optimal sampling size and the height threshold should be determined to improve the estimation accuracy of biophysical parameters. Our results also implied that a higher LiDAR point density, larger sampling size and height threshold were required to obtain accurate corn LAI estimation when compared with height and biomass estimations. In general, our results provide valuable guidance for LiDAR data acquisition and estimation of vegetation biophysical parameters using LiDAR data.

Systems and methods that generate height map models for efficient three dimensional reconstruction from depth information

DOEpatents

Frahm, Jan-Michael; Pollefeys, Marc Andre Leon; Gallup, David Robert

2015-12-08

Methods of generating a three dimensional representation of an object in a reference plane from a depth map including distances from a reference point to pixels in an image of the object taken from a reference point. Weights are assigned to respective voxels in a three dimensional grid along rays extending from the reference point through the pixels in the image based on the distances in the depth map from the reference point to the respective pixels, and a height map including an array of height values in the reference plane is formed based on the assigned weights. An n-layer height map may be constructed by generating a probabilistic occupancy grid for the voxels and forming an n-dimensional height map comprising an array of layer height values in the reference plane based on the probabilistic occupancy grid.

Perceived displacement explains wolfpack effect

PubMed Central

Šimkovic, Matúš; Träuble, Birgit

2014-01-01

We investigate the influence of perceived displacement of moving agent-like stimuli on the performance in dynamic interactive tasks. In order to reliably measure perceived displacement we utilize multiple tasks with different task demands. The perceived center of an agent's body is displaced in the direction in which the agent is facing and this perceived displacement is larger than the theoretical position of the center of mass would predict. Furthermore, the displacement in the explicit judgment is dissociated from the displacement obtained by the implicit measures. By manipulating the location of the pivot point, we show that it is not necessary to postulate orientation as an additional cue utilized by perception, as has been suggested by earlier studies. These studies showed that the agent's orientation influences the detection of chasing motion and the detection-related performance in interactive tasks. This influence has been labeled wolfpack effect. In one of the demonstrations of the wolfpack effect participants control a green circle on a display with a computer mouse. It has been shown that participants avoid display areas with agents pointing toward the green circle. Participants do so in favor of areas where the agents point in the direction perpendicular to the circle. We show that this avoidance behavior arises because the agent's pivot point selected by the earlier studies is different from where people locate the center of agent's body. As a consequence, the nominal rotation confounds rotation and translation. We show that the avoidance behavior disappears once the pivot point is set to the center of agent's body. PMID:25566114

Method of vibration isolating an aircraft engine

NASA Technical Reports Server (NTRS)

Bender, Stanley I. (Inventor); Butler, Lawrence (Inventor); Dawes, Peter W. (Inventor)

1991-01-01

A method for coupling an engine to a support frame for mounting to a fuselage of an aircraft using a three point vibration isolating mounting system in which the load reactive forces at each mounting point are statically and dynamically determined. A first vibration isolating mount pivotably couples a first end of an elongated support beam to a stator portion of an engine with the pivoting action of the vibration mount being oriented such that it is pivotable about a line parallel to a center line of the engine. An aft end of the supporting frame is coupled to the engine through an additional pair of vibration isolating mounts with the mounts being oriented such that they are pivotable about a circumference of the engine. The aft mounts are symmetrically spaced to each side of the supporting frame by 45 degrees. The relative orientation between the front mount and the pair of rear mounts is such that only the rear mounts provide load reactive forces parallel to the engine center line, in support of the engine to the aircraft against thrust forces. The forward mount is oriented so as to provide only radial forces to the engine and some lifting forces to maintain the engine in position adjacent a fuselage. Since each mount is connected to provide specific forces to support the engine, forces required of each mount are statically and dynamically determinable.

Point of optimal kinematic error: improvement of the instantaneous helical pivot method for locating centers of rotation.

PubMed

De Rosario, Helios; Page, Alvaro; Mata, Vicente

2014-05-07

This paper proposes a variation of the instantaneous helical pivot technique for locating centers of rotation. The point of optimal kinematic error (POKE), which minimizes the velocity at the center of rotation, may be obtained by just adding a weighting factor equal to the square of angular velocity in Woltring׳s equation of the pivot of instantaneous helical axes (PIHA). Calculations are simplified with respect to the original method, since it is not necessary to make explicit calculations of the helical axis, and the effect of accidental errors is reduced. The improved performance of this method was validated by simulations based on a functional calibration task for the gleno-humeral joint center. Noisy data caused a systematic dislocation of the calculated center of rotation towards the center of the arm marker cluster. This error in PIHA could even exceed the effect of soft tissue artifacts associated to small and medium deformations, but it was successfully reduced by the POKE estimation. Copyright © 2014 Elsevier Ltd. All rights reserved.

Structural Dynamics of Maneuvering Aircraft.

DTIC Science & Technology

1987-09-01

MANDYN. Written in Fortran 77, it was compiled and executed with Microsoft Fortran, Vers. 4.0 on an IBM PC-AT, with a co-processor, and a 20M hard disk...to the pivot area. Pre- sumably, the pivot area is a hard point in the wing structure. -41- NADC M1i4-0 ResulIts The final mass and flexural rigidity...lowest mode) is an important parameter. If it is less than three, the load factor approach can be problema - tical. In assessing the effect of one maneuver

Differences in biological maturation, anthropometry and physical performance between playing positions in youth team handball.

PubMed

Matthys, Stijn P J; Fransen, Job; Vaeyens, Roel; Lenoir, Matthieu; Philippaerts, Renaat

2013-01-01

It was the goal of this cross-sectional study to examine differences in maturity, anthropometry and physical performance between youth handball players across different playing positions (i.e. goalkeeper, back, pivot and wing). Multivariate analysis of covariance (MANCOVA), accounting for biological maturation, was used to assess positional differences in 472 male youth handball players from three age groups: U14, U15 and U16. Differences in age at peak height velocity were found in all age groups. Backs were significantly more mature than wings in U14 and U15 and than wings and pivots in U16. Furthermore, backs are overall taller, have a bigger arm span and perform best on tests for strength, agility and speed, especially in the U15 age group. Therefore, it can be concluded that youth players with the most advanced maturation status and the most favourable anthropometry and physical fitness scores, are consistently positioned in the back position. Players with a less advanced maturity status and an overall smaller stature are placed on the wing or pivot positions. In conclusion, it seems that anthropometrical and maturational characteristics are used by coaches to directly and/or indirectly select players for specific field positions. This strategy is risky since anthropometry and maturity status change over the years.

Near constant-time optimal piecewise LDR to HDR inverse tone mapping

NASA Astrophysics Data System (ADS)

Chen, Qian; Su, Guan-Ming; Yin, Peng

2015-02-01

In a backward compatible HDR image/video compression, it is a general approach to reconstruct HDR from compressed LDR as a prediction to original HDR, which is referred to as inverse tone mapping. Experimental results show that 2- piecewise 2nd order polynomial has the best mapping accuracy than 1 piece high order or 2-piecewise linear, but it is also the most time-consuming method because to find the optimal pivot point to split LDR range to 2 pieces requires exhaustive search. In this paper, we propose a fast algorithm that completes optimal 2-piecewise 2nd order polynomial inverse tone mapping in near constant time without quality degradation. We observe that in least square solution, each entry in the intermediate matrix can be written as the sum of some basic terms, which can be pre-calculated into look-up tables. Since solving the matrix becomes looking up values in tables, computation time barely differs regardless of the number of points searched. Hence, we can carry out the most thorough pivot point search to find the optimal pivot that minimizes MSE in near constant time. Experiment shows that our proposed method achieves the same PSNR performance while saving 60 times computation time compared to the traditional exhaustive search in 2-piecewise 2nd order polynomial inverse tone mapping with continuous constraint.

The carbon balance pivot point of southwestern U.S. semiarid ecosystems: Insights from the 21st century drought

NASA Astrophysics Data System (ADS)

Scott, Russell L.; Biederman, Joel A.; Hamerlynck, Erik P.; Barron-Gafford, Greg A.

2015-12-01

Global-scale studies indicate that semiarid regions strongly regulate the terrestrial carbon sink. However, we lack understanding of how climatic shifts, such as decadal drought, impact carbon sequestration across the wide range of structural diversity in semiarid ecosystems. Therefore, we used eddy covariance measurements to quantify how net ecosystem production of carbon dioxide (NEP) differed with relative grass and woody plant abundance over the last decade of drought in four Southwest U.S. ecosystems. We identified a precipitation "pivot point" in the carbon balance for each ecosystem where annual NEP switched from negative to positive. Ecosystems with grass had pivot points closer to the drought period precipitation than the predrought average, making them more likely to be carbon sinks (and a grass-free shrubland, a carbon source) during the current drought. One reason for this is that the grassland located closest to the shrubland supported higher leaf area and photosynthesis at the same water availability. Higher leaf area was associated with a greater proportion of evapotranspiration being transpiration (T/ET), and therefore with higher ecosystem water use efficiency (gross ecosystem photosynthesis/ET). Our findings strongly show that water availability is a primary driver of both gross and net semiarid productivity and illustrate that structural differences may contribute to the speed at which ecosystem carbon cycling adjusts to climatic shifts.

Toggle mechanism for pinching metal tubes

NASA Technical Reports Server (NTRS)

Stengard, E. O. (Inventor)

1979-01-01

A toggle mechanism pinches a metal tube and maintains the tube in a pinched condition, without fracturing. The toggle mechanism includes a plunger translatable along a longitudinal axis, as well as a pair of links pivoted about a common axis extending through an end of the plunger. One of the links also pivots about a fixed axis. A free end of the other link carries a push link which the other link translates at right angles to the plunger longitudinal axis. First and second sides of the tube bear against a first stop block and are engaged by the push link when a compression spring, attached to the plunger, is suddenly released to irreversibly drive the plunger along its longitudinal axis so the pivot point of the two links is driven to an over travel position.

Critical current scaling and the pivot-point in Nb3Sn strands

NASA Astrophysics Data System (ADS)

Tsui, Y.; Hampshire, D. P.

2012-05-01

Detailed measurements are provided of the engineering critical current density (Jc) and the index of transition (n-value) of two different types of advanced ITER Nb3Sn superconducting strand for fusion applications. The samples consist of one internal-tin strand (OST) and two bronze-route strands (BEAS I and BEAS II—reacted using different heat treatments). Tests on different sections of these wires show that prior to applying strain, Jc is homogeneous to better than 2% along the length of each strand. Jc data have been characterized as a function of magnetic field (B ≤ 14.5 T), temperature (4.2 K ≤ T ≤ 12 K) and applied axial strain ( - 1% ≤ ɛA ≤ 0.8%). Strain-cycling tests demonstrate that the variable strain Jc data are reversible to better than 2% when the applied axial strain is in the range of - 1% ≤ ɛA ≤ 0.5%. The wires are damaged when the intrinsic strain (ɛI) is ɛI ≥ 0.55% and ɛI ≥ 0.23% for the OST and BEAS strands, respectively. The strain dependences of the normalized Jc for each type of strand are similar to those of prototype strands of similar design measured in 2005 and 2008 to about 2% which makes them candidate strands for a round-robin interlaboratory comparison. The Jc data are described by Durham, ITER and Josephson-junction parameterizations to an accuracy of about 4%. For all of these scaling laws, the percentage difference between the data and the parameterization is larger when Jc is small, caused by high B, T or |ɛI|. The n-values can be described by a modified power law of the form n=1+r{I}_{{c}}^{s}, where r and s are approximately constant and Ic is the critical current. It has long been known that pivot-points (or cross-overs) in Jc occur at high magnetic field and temperature. Changing the magnetic field or temperature from one side of the pivot-point to the other changes the highest Jc sample to the lowest Jc sample and vice versa. The pivot-point follows the B-T phase boundary associated with the upper critical field and is usually attributed to the different tin content profiles and pinning properties of internal-tin and bronze-route strands. We report that the strain dependence of the pivot-point in these strands is quite different from that of the upper critical field and suggest that its origin in optimized high tin content strands is the proximity of the tetragonal Nb3Sn phase, which has low superconducting critical parameters.

The pleiotropic ABNORMAL FLOWER AND DWARF1 affects plant height, floral development and grain yield in rice.

PubMed

Ren, Deyong; Rao, Yuchun; Wu, Liwen; Xu, Qiankun; Li, Zizhuang; Yu, Haiping; Zhang, Yu; Leng, Yujia; Hu, Jiang; Zhu, Li; Gao, Zhenyu; Dong, Guojun; Zhang, Guangheng; Guo, Longbiao; Zeng, Dali; Qian, Qian

2016-06-01

Moderate plant height and successful establishment of reproductive organs play pivotal roles in rice grain production. The molecular mechanism that controls the two aspects remains unclear in rice. In the present study, we characterized a rice gene, ABNORMAL FLOWER AND DWARF1 (AFD1) that determined plant height, floral development and grain yield. The afd1 mutant showed variable defects including the dwarfism, long panicle, low seed setting and reduced grain yield. In addition, abnormal floral organs were also observed in the afd1 mutant including slender and thick hulls, and hull-like lodicules. AFD1 encoded a DUF640 domain protein and was expressed in all tested tissues and organs. Subcellular localization showed AFD1-green fluorescent fusion protein (GFP) was localized in the nucleus. Meantime, our results suggested that AFD1 regulated the expression of cell division and expansion related genes. © 2015 The Authors. Journal of Integrative Plant Biology published by John Wiley & Sons Australia, Ltd on behalf of Institute of Botany, Chinese Academy of Sciences.

New fundamental parameters for attitude representation

NASA Astrophysics Data System (ADS)

Patera, Russell P.

2017-08-01

A new attitude parameter set is developed to clarify the geometry of combining finite rotations in a rotational sequence and in combining infinitesimal angular increments generated by angular rate. The resulting parameter set of six Pivot Parameters represents a rotation as a great circle arc on a unit sphere that can be located at any clocking location in the rotation plane. Two rotations are combined by linking their arcs at either of the two intersection points of the respective rotation planes. In a similar fashion, linking rotational increments produced by angular rate is used to derive the associated kinematical equations, which are linear and have no singularities. Included in this paper is the derivation of twelve Pivot Parameter elements that represent all twelve Euler Angle sequences, which enables efficient conversions between Pivot Parameters and any Euler Angle sequence. Applications of this new parameter set include the derivation of quaternions and the quaternion composition rule, as well as, the derivation of the analytical solution to time dependent coning motion. The relationships between Pivot Parameters and traditional parameter sets are included in this work. Pivot Parameters are well suited for a variety of aerospace applications due to their effective composition rule, singularity free kinematic equations, efficient conversion to and from Euler Angle sequences and clarity of their geometrical foundation.

Effects of off-axis elliptical training on reducing pain and improving knee function in individuals with patellofemoral pain

PubMed Central

Tsai, Liang-Ching; Lee, Song Joo; Yang, Aaron J.; Ren, Yupeng; Press, Joel M.; Zhang, Li-Qun

2014-01-01

Objective To examine whether an off-axis elliptical training program reduces pain and improves knee function in individuals with patellofemoral pain (PFP). Design Controlled laboratory study, pre-test-post-test. Setting University rehabilitation center. Participants Twelve adult subjects with PFP. Interventions Subjects with PFP completed an exercise program consisting of 18 sessions of lower extremity off-axis training using a custom-made elliptical trainer that allows frontal-plane sliding and transverse-plane pivoting of the footplates. Main Outcome Measures Changes in knee pain and function post-training and 6 weeks following training were evaluated using the Knee Injury and Osteoarthritis Outcome Score (KOOS) and International Knee Documentation Committee (IKDC) scores. Lower extremity off-axis control was assessed by pivoting and sliding instability, calculated as the root mean square (RMS) of the footplate pivoting angle and sliding distance during elliptical exercise. Subjects’ single-leg hop distance and proprioception in detecting lower extremity pivoting motion were also evaluated. Results Subjects reported significantly greater KOOS and IKDC scores (increased by 12–18 points) and hop distance (increased by 0.2 m) following training. A significant decrease in the pivoting and sliding RMS was also observed following training. Additionally, subjects with PFP demonstrated improved pivoting proprioception when tested under a minimum-weight-bearing position. Conclusions An off-axis elliptical training program was effective in enhancing lower extremity neuromuscular control on the frontal and transverse planes, reducing pain and improving knee function in persons with PFP. PMID:25591131

Remote pivot decoupler pylon: Wing/store flutter suppressor

NASA Technical Reports Server (NTRS)

Hassler, J. M., Jr. (Inventor)

1986-01-01

A device for suspending a store from an aerodynamic support surface, such an an aircraft wing, and more specifically, for improving upon singlet pivot decoupler pylons by reducing both frequency of active store, alignment, and alignment system space and power requirements. Two links suspend a lower pylon/rack section and releasable attached store from an upper pylon section mounted under the wing. The links allow the lower pylon section to rotate in pitch about a remote pivot point. A leaf spring connected between the lower section and electrical alignment system servomechanism provides pitch alignment of the lower section/store combination. The servomechanism utilizes an electric servomotor to drive the gear train and reversibly move the leaf spring, thereby maintaining the pitch attitude of the store within acceptable limits. The damper strokes when the lower section rotates to damp large oscillations of store.

Thigh Muscle Activity, Knee Motion, and Impact Force During Side-Step Pivoting in Agility-Trained Female Basketball Players

PubMed Central

Wilderman, Danielle R; Ross, Scott E; Padua, Darin A

2009-01-01

Context: Improving neuromuscular control of hamstrings muscles might have implications for decreasing anterior cruciate ligament injuries in females. Objective: To examine the effects of a 6-week agility training program on quadriceps and hamstrings muscle activation, knee flexion angles, and peak vertical ground reaction force. Design: Prospective, randomized clinical research trial. Setting: Sports medicine research laboratory. Patients or Other Participants: Thirty female intramural basketball players with no history of knee injury (age  =  21.07 ± 2.82 years, height  =  171.27 ± 4.66 cm, mass  =  66.36 ± 7.41 kg). Intervention(s): Participants were assigned to an agility training group or a control group that did not participate in agility training. Participants in the agility training group trained 4 times per week for 6 weeks. Main Outcome Measure(s): We used surface electromyography to assess muscle activation for the rectus femoris, vastus medialis oblique, medial hamstrings, and lateral hamstrings for 50 milliseconds before initial ground contact and while the foot was in contact with the ground during a side-step pivot maneuver. Knee flexion angles (at initial ground contact, maximum knee flexion, knee flexion displacement) and peak vertical ground reaction force also were assessed during this maneuver. Results: Participants in the training group increased medial hamstrings activation during ground contact after the 6-week agility training program. Both groups decreased their vastus medialis oblique muscle activation during ground contact. Knee flexion angles and peak vertical ground reaction force did not change for either group. Conclusions: Agility training improved medial hamstrings activity in female intramural basketball players during a side-step pivot maneuver. Agility training that improves hamstrings activity might have implications for reducing anterior cruciate ligament sprain injury associated with side-step pivots. PMID:19180214

Height Accuracy Based on Different Rtk GPS Method for Ultralight Aircraft Images

NASA Astrophysics Data System (ADS)

Tahar, K. N.

2015-08-01

Height accuracy is one of the important elements in surveying work especially for control point's establishment which requires an accurate measurement. There are many methods can be used to acquire height value such as tacheometry, leveling and Global Positioning System (GPS). This study has investigated the effect on height accuracy based on different observations which are single based and network based GPS methods. The GPS network is acquired from the local network namely Iskandar network. This network has been setup to provide real-time correction data to rover GPS station while the single network is based on the known GPS station. Nine ground control points were established evenly at the study area. Each ground control points were observed about two and ten minutes. It was found that, the height accuracy give the different result for each observation.

Development of a Mathematical Model to Assess the Accuracy of Difference between Geodetic Heights

ERIC Educational Resources Information Center

Gairabekov, Ibragim; Kliushin, Evgenii; Gayrabekov, Magomed-Bashir; Ibragimova, Elina; Gayrabekova, Amina

2016-01-01

The article includes the results of theoretical studies of the accuracy of geodetic height survey and marks points on the Earth's surface using satellite technology. The dependence of the average square error of geodetic heights difference survey from the distance to the base point was detected. It is being proved that by using satellite…

Monitoring small pioneer trees in the forest-tundra ecotone: using multi-temporal airborne laser scanning data to model height growth.

PubMed

Hauglin, Marius; Bollandsås, Ole Martin; Gobakken, Terje; Næsset, Erik

2017-12-08

Monitoring of forest resources through national forest inventory programmes is carried out in many countries. The expected climate changes will affect trees and forests and might cause an expansion of trees into presently treeless areas, such as above the current alpine tree line. It is therefore a need to develop methods that enable the inclusion of also these areas into monitoring programmes. Airborne laser scanning (ALS) is an established tool in operational forest inventories, and could be a viable option for monitoring tasks. In the present study, we used multi-temporal ALS data with point density of 8-15 points per m 2 , together with field measurements from single trees in the forest-tundra ecotone along a 1500-km-long transect in Norway. The material comprised 262 small trees with an average height of 1.78 m. The field-measured height growth was derived from height measurements at two points in time. The elapsed time between the two measurements was 4 years. Regression models were then used to model the relationship between ALS-derived variables and tree heights as well as the height growth. Strong relationships between ALS-derived variables and tree heights were found, with R 2 values of 0.93 and 0.97 for the two points in time. The relationship between the ALS data and the field-derived height growth was weaker, with R 2 values of 0.36-0.42. A cross-validation gave corresponding results, with root mean square errors of 19 and 11% for the ALS height models and 60% for the model relating ALS data to single-tree height growth.

[New approaches in the treatment of short stature].

PubMed

Zung, Amnon; Zadik, Zvi

2002-12-01

Over the past years, the efforts to improve the final height of children with short stature has yielded new modalities of therapy. New types of injection devices, mainly ready-to-use injection pens with multi-dose vials of reconstituted growth hormone (GH), have made the treatment technically easier and less stressful for the patients. A new type of slow-release GH injected once or twice a month has recently been studied. In addition, several types of synthetic GH-secretagogues were examined, with the advantage of being introduced by the oral or nasal route. The recognition of the pivotal role of estrogens in skeletal maturation and subsequent growth arrest, was the basis for the use of aromatase inhibitor in a pioneering study, with promising results. We have concluded the review with an update on the benefit of GH therapy in children with normal short stature, based on 12 studies that provided data on the final height of these children.

Global height datum unification: a new approach in gravity potential space

NASA Astrophysics Data System (ADS)

Ardalan, A. A.; Safari, A.

2005-12-01

The problem of “global height datum unification” is solved in the gravity potential space based on: (1) high-resolution local gravity field modeling, (2) geocentric coordinates of the reference benchmark, and (3) a known value of the geoid’s potential. The high-resolution local gravity field model is derived based on a solution of the fixed-free two-boundary-value problem of the Earth’s gravity field using (a) potential difference values (from precise leveling), (b) modulus of the gravity vector (from gravimetry), (c) astronomical longitude and latitude (from geodetic astronomy and/or combination of (GNSS) Global Navigation Satellite System observations with total station measurements), (d) and satellite altimetry. Knowing the height of the reference benchmark in the national height system and its geocentric GNSS coordinates, and using the derived high-resolution local gravity field model, the gravity potential value of the zero point of the height system is computed. The difference between the derived gravity potential value of the zero point of the height system and the geoid’s potential value is computed. This potential difference gives the offset of the zero point of the height system from geoid in the “potential space”, which is transferred into “geometry space” using the transformation formula derived in this paper. The method was applied to the computation of the offset of the zero point of the Iranian height datum from the geoid’s potential value W 0=62636855.8 m2/s2. According to the geometry space computations, the height datum of Iran is 0.09 m below the geoid.

Multitemporal field-based plant height estimation using 3D point clouds generated from small unmanned aerial systems high-resolution imagery

NASA Astrophysics Data System (ADS)

Malambo, L.; Popescu, S. C.; Murray, S. C.; Putman, E.; Pugh, N. A.; Horne, D. W.; Richardson, G.; Sheridan, R.; Rooney, W. L.; Avant, R.; Vidrine, M.; McCutchen, B.; Baltensperger, D.; Bishop, M.

2018-02-01

Plant breeders and agronomists are increasingly interested in repeated plant height measurements over large experimental fields to study critical aspects of plant physiology, genetics and environmental conditions during plant growth. However, collecting such measurements using commonly used manual field measurements is inefficient. 3D point clouds generated from unmanned aerial systems (UAS) images using Structure from Motion (SfM) techniques offer a new option for efficiently deriving in-field crop height data. This study evaluated UAS/SfM for multitemporal 3D crop modelling and developed and assessed a methodology for estimating plant height data from point clouds generated using SfM. High-resolution images in visible spectrum were collected weekly across 12 dates from April (planting) to July (harvest) 2016 over 288 maize (Zea mays L.) and 460 sorghum (Sorghum bicolor L.) plots using a DJI Phantom 3 Professional UAS. The study compared SfM point clouds with terrestrial lidar (TLS) at two dates to evaluate the ability of SfM point clouds to accurately capture ground surfaces and crop canopies, both of which are critical for plant height estimation. Extended plant height comparisons were carried out between SfM plant height (the 90th, 95th, 99th percentiles and maximum height) per plot and field plant height measurements at six dates throughout the growing season to test the repeatability and consistency of SfM estimates. High correlations were observed between SfM and TLS data (R2 = 0.88-0.97, RMSE = 0.01-0.02 m and R2 = 0.60-0.77 RMSE = 0.12-0.16 m for the ground surface and canopy comparison, respectively). Extended height comparisons also showed strong correlations (R2 = 0.42-0.91, RMSE = 0.11-0.19 m for maize and R2 = 0.61-0.85, RMSE = 0.12-0.24 m for sorghum). In general, the 90th, 95th and 99th percentile height metrics had higher correlations to field measurements than the maximum metric though differences among them were not statistically significant. The accuracy of SfM plant height estimates fluctuated over the growing period, likely impacted by the changing reflectance regime due to plant development. Overall, these results show a potential path to reducing laborious manual height measurement and enhancing plant research programs through UAS and SfM.

Evolution of branch points for a laser beam propagating through an uplink turbulent atmosphere.

PubMed

Ge, Xiao-Lu; Liu, Xuan; Guo, Cheng-Shan

2014-03-24

Evolution of branch points in the distorted optical field is studied when a laser beam propagates through turbulent atmosphere along an uplink path. Two categories of propagation events are mainly explored for the same propagation height: fixed wavelength with change of the turbulence strength and fixed turbulence strength with change of the wavelength. It is shown that, when the beam propagates to a certain height, the density of the branch-points reaches its maximum and such a height changes with the turbulence strength but nearly remains constant with different wavelengths. The relationship between the density of branch-points and the Rytov number is also given. A fitted formula describing the relationship between the density of branch-points and propagation height with different turbulence strength and wavelength is found out. Interestingly, this formula is very similar to the formula used for describing the Blackbody radiation in physics. The results obtained may be helpful for atmospheric optics, astronomy and optical communication.

Height Control and Deposition Measurement for the Electron Beam Free Form Fabrication (EBF3) Process

NASA Technical Reports Server (NTRS)

Hafley, Robert A. (Inventor); Seufzer, William J. (Inventor)

2017-01-01

A method of controlling a height of an electron beam gun and wire feeder during an electron freeform fabrication process includes utilizing a camera to generate an image of the molten pool of material. The image generated by the camera is utilized to determine a measured height of the electron beam gun relative to the surface of the molten pool. The method further includes ensuring that the measured height is within the range of acceptable heights of the electron beam gun relative to the surface of the molten pool. The present invention also provides for measuring a height of a solid metal deposit formed upon cooling of a molten pool. The height of a single point can be measured, or a plurality of points can be measured to provide 2D or 3D surface height measurements.

Analysis of ICESat Data Using Kalman Filter and Kriging to Study Height Changes in East Antarctica

NASA Technical Reports Server (NTRS)

Herring, Thomas A.

2005-01-01

We analyze ICESat derived heights collected between Feb. 03-Nov. 04 using a kriging/Kalman filtering approach to investigate height changes in East Antarctica. The model's parameters are height change to an a priori static digital height model, seasonal signal expressed as an amplitude Beta and phase Theta, and height-change rate dh/dt for each (100 km)(exp 2) block. From the Kalman filter results, dh/dt has a mean of -0.06 m/yr in the flat interior of East Antarctica. Spatially correlated pointing errors in the current data releases give uncertainties in the range 0.06 m/yr, making height change detection unreliable at this time. Our test shows that when using all available data with pointing knowledge equivalent to that of Laser 2a, height change detection with an accuracy level 0.02 m/yr can be achieved over flat terrains in East Antarctica.

Remeasuring tree heights on permanent plots using rectangular coordinates and one angle per tree

Treesearch

Robert L. Neal

1973-01-01

Heights of permanent sample trees with tops visible from any point can be measured from that point with any clinometer, measuring one vertical angle per tree. Two horizontal angles and one additional vertical angle per observation point are necessary to orient the point to the plot. Permanently recorded coordinates and elevations of tree locations are used with the...

Forest Biomass Mapping from Stereo Imagery and Radar Data

NASA Astrophysics Data System (ADS)

Sun, G.; Ni, W.; Zhang, Z.

2013-12-01

Both InSAR and lidar data provide critical information on forest vertical structure, which are critical for regional mapping of biomass. However, the regional application of these data is limited by the availability and acquisition costs. Some researchers have demonstrated potentials of stereo imagery in the estimation of forest height. Most of these researches were conducted on aerial images or spaceborne images with very high resolutions (~0.5m). Space-born stereo imagers with global coverage such as ALOS/PRISM have coarser spatial resolutions (2-3m) to achieve wider swath. The features of stereo images are directly affected by resolutions and the approaches use by most of researchers need to be adjusted for stereo imagery with lower resolutions. This study concentrated on analyzing the features of point clouds synthesized from multi-view stereo imagery over forested areas. The small footprint lidar and lidar waveform data were used as references. The triplets of ALOS/PRISM data form three pairs (forward/nadir, backward/nadir and forward/backward) of stereo images. Each pair of the stereo images can be used to generate points (pixels) with 3D coordinates. By carefully co-register these points from three pairs of stereo images, a point cloud data was generated. The height of each point above ground surface was then calculated using DEM from National Elevation Dataset, USGS as the ground surface elevation. The height data were gridded into pixel of different sizes and the histograms of the points within a pixel were analyzed. The average height of the points within a pixel was used as the height of the pixel to generate a canopy height map. The results showed that the synergy of point clouds from different views were necessary, which increased the point density so the point cloud could detect the vertical structure of sparse and unclosed forests. The top layer of multi-layered forest could be captured but the dense forest prevented the stereo imagery to see through. The canopy height map exhibited spatial patterns of roads, forest edges and patches. The linear regression showed that the canopy height map had a good correlation with RH50 of LVIS data at 30m pixel size with a gain of 1.04, bias of 4.3m and R2 of 0.74 (Fig. 1). The canopy height map from PRISM and dual-pol PALSAR data were used together to map biomass in our study area near Howland, Maine, and the results were evaluated using biomass map generated from LVIS waveform data independently. The results showed that adding CHM from PRISM significantly improved biomass accuracy and raised the biomass saturation level of L-band SAR data in forest biomass mapping.

Southeast Oahu Coastal Hydrodynamic Modeling with ADCIRC and STWAVE

DTIC Science & Technology

2008-07-01

19 Figure 16. CDIP buoy locations...20 Figure 17. Wave height versus wave direction percent occurrence rose for CDIP Buoy 098 – Mokapu Point, HI...wave height versus wave period for CDIP Buoy 098 – Mokapu Point, HI

Tumor shrinkage and objective response rates: gold standard for oncology efficacy screening trials, or an outdated end point?

PubMed

Bradbury, Penelope; Seymour, Lesley

2009-01-01

Phase II clinical trials have long been used to screen new cancer therapeutics for antitumor activity ("efficacy") worthy of further evaluation. Traditionally, the primary end point used in these screening trials has been objective response rate (RR), with the desired rate being arbitrarily set by the researchers before initiation of the trial. For cytotoxic agents, especially in common tumor types, response has been a reasonably robust and validated surrogate of benefit. Phase II trials with response as an end point have a modest sample size (15-40 patients) and are completed rapidly allowing early decisions regarding future development of a given agent. More recently, a number of new agents have proven successful in pivotal phase III studies, despite a low or very modest RR demonstrated in early clinical trials. Researchers have postulated that these novel agents, as a class, may not induce significant regression of tumors, and that the use of RR as an end point for phase II studies will result in false negative results, and point out that not all available data is used in making the decision. Others have pointed out that even novel agents have proven unsuccessful in pivotal trials if objective responses are not demonstrated in early clinical trials. We review here the historical and current information regarding objective tumor response.

Physiological consequences of height-related morphological variation in Sequoia sempervirens foliage.

PubMed

Mullin, Lucy P; Sillett, Stephen C; Koch, George W; Tu, Kevin P; Antoine, Marie E

2009-08-01

This study examined relationships between foliar morphology and gas exchange characteristics as they vary with height within and among crowns of Sequoia sempervirens D. Don trees ranging from 29 to 113 m in height. Shoot mass:area (SMA) ratio increased with height and was less responsive to changes in light availability as height increased, suggesting a transition from light to water relations as the primary determinant of morphology with increasing height. Mass-based rates of maximum photosynthesis (A(max,m)), standardized photosynthesis (A(std,m)) and internal CO(2) conductance (g(i,m)) decreased with height and SMA, while the light compensation point, light saturation point, and mass and area-based rates of dark respiration (R(m)) increased with height and SMA. Among foliage from different heights, much of the variation in standardized photosynthesis was explained by variation in g(i,) consistent with increasing limitation of photosynthesis by internal conductance in foliage with higher SMA. The syndrome of lower internal and stomatal conductance to CO(2) and higher respiration may contribute to reductions in upper crown growth efficiency with increasing height in S. sempervirens trees.

Quantitative comparison of the pivot shift test results before and after anterior cruciate ligament reconstruction by using the three-dimensional electromagnetic measurement system.

PubMed

Nagai, Kanto; Hoshino, Yuichi; Nishizawa, Yuichiro; Araki, Daisuke; Matsushita, Takehiko; Matsumoto, Tomoyuki; Takayama, Koji; Nagamune, Kouki; Kurosaka, Masahiro; Kuroda, Ryosuke

2015-10-01

Tibial acceleration during the pivot shift test is a potential quantitative parameter to evaluate rotational laxity of anterior cruciate ligament (ACL) insufficiency. However, clinical application of this measurement has not been fully examined. This study aimed to measure and compare tibial acceleration before and after ACL reconstruction (ACLR) in ACL-injured patients. We hypothesized tibial acceleration would be reduced by ACLR and tibial acceleration would be consistent in the same knee at different time points. Seventy ACL-injured patients who underwent ACLR were enrolled. Tibial acceleration during the pivot shift test was measured using an electromagnetic measurement system before ALCR and at the second-look arthroscopy 1 year post-operatively. Tibial acceleration was compared to clinical grading and between ACL-injured/ACL-reconstructed and contralateral knees. Pre-operative tibial acceleration was increased stepwise with the increase in clinical grading (P < 0.01). Tibial acceleration in ACL-injured knee (1.9 ± 1.2 m/s(2)) was larger than that in the contralateral knee (0.8 ± 0.3 m/s(2), P < 0.01), and reduced to 0.9 ± 0.3 m/s(2) post-operatively (P < 0.01). There was no difference between ACL-reconstructed and contralateral knee (n.s.). Tibial acceleration in contralateral knees was consistent pre- and post-operatively (n.s.). Tibial acceleration measurement demonstrated increased rotational laxity in ACL-injured knees and its reduction by ALCR. Additionally, consistent measurements were obtained in ACL-intact knees at different time points. Therefore, tibial acceleration during the pivot shift test could provide quantitative evaluation of rotational stability before and after ACL reconstruction. III.

Intratarsal fixation at the same level as the skin incision to reduce asymmetric double eyelids: evaluation of symmetry using photogrammetry.

PubMed

Han, Kihwan; Yeo, Hyeonjung; Choi, Tae Hyun; Son, Daegu; Kim, Jun Hyung

2010-03-01

One of the most common complications of double eyelid operations is asymmetry. To reduce asymmetry, we fixed the dermis to the tarsal plate at the same level as the skin incision, and objectively evaluated the symmetry of the height using photogrammetry.Of 30 patients who had double eyelid operations by the intratarsal fixation technique, 15 patients completed a minimum follow-up of 6 months. After the skin incision and removal of the orbicularis oculi muscle and the orbital fat, the pretarsal fat pad was excised to expose the superior portion of the tarsal plate. The 3 fixation points were marked on the tarsal plate at the same level with the skin incision using a spreading caliper. The dermis was fixed to the marked points of the tarsal plate and the skin was closed.The height of the double eyelid was measured by clinical photography at 4 points when the eyes were opened and at 3 points when the eyes were closed. The height proportional index at each point was obtained by dividing the height of the left double eyelid by that of the right double eyelid. We compared each height proportional index with "1" to evaluate the symmetry of both double eyelids using a paired t test.The follow-up period was an average of 9.0 months. The mean height proportional indices were 0.97 (a), 0.96 (b), 0.98 (c), 1.08 (d), 0.97 (e), 1.02 (f), and 1.13 (g). According to a paired t test, the height of the left double eyelid was not different from that of the right double eyelid.Intratarsal fixation, along with other previously known methods, decreases asymmetric double eyelids.

Randomized Double-Blind Phase III Pivotal Field Trial of the Comparative Immunogenicity Safety and Tolerability of Two Yellow Fever 17D Vaccines (ARILVAX(Trademark) and YF-VAX(Trademark)) in Healthy Infants and Children in Peru

DTIC Science & Technology

2004-08-17

Expertos: Estrategias de Prevencion y Control de la Fiebre Amarilla y Riesgo de Urbanizacion en las Americas. May 14–15, 1998. Lima, Peru: U.S. Agency...which vaccination is indicated in en - demic areas. The origin, derivation, production, and genomic sequences of these vaccines have been previously de...by study site, mean age, sex, weight (in kg), height (in cm), body mass index (kg/m2), pulse (beats per minute), allergy history, anaphylac- tic

16 CFR 309.17 - Labels.

Code of Federal Regulations, 2010 CFR

2010-01-01

... height) knocked out of a 1″ (2.54 cm) deep band. The type for the words “MINIMUM” and the principal... should be set as “normal.” The type for the fuel name is 50 point (1/2″ 1.27 cm) cap height) knocked out... point (1/2″ 1.27 cm) cap height) knocked out of a 1″ (2.54 cm) deep band. All other type is 24 pt. (1/4...

16 CFR 309.17 - Labels.

Code of Federal Regulations, 2011 CFR

2011-01-01

... height) knocked out of a 1″ (2.54 cm) deep band. The type for the words “MINIMUM” and the principal... should be set as “normal.” The type for the fuel name is 50 point (1/2″ 1.27 cm) cap height) knocked out... point (1/2″ 1.27 cm) cap height) knocked out of a 1″ (2.54 cm) deep band. All other type is 24 pt. (1/4...

Planning for the integration of the digital library, clinical decision support, and evidence at the point of care.

PubMed

Schwartz, Linda Matula; Iobst, Barbara

2008-01-01

Integrating knowledge-based resources at the point of care is an important opportunity for hospital library involvement. In the progression of an IAIMS planning grant, the digital library is recognized as pivotal to the success of information domain integration throughout the institution. The planning process, data collection, and evolution of the planning project are discussed.

Geometric analysis of the V-Y advancement flap and its clinical applications.

PubMed

Andrades, Patricio R; Calderon, Wilfredo; Leniz, Patricio; Bartel, German; Danilla, Stefan; Benitez, Susana

2005-05-01

Geometry is fundamental in the comprehension of local flap design. The purpose of this study was to discuss the differences between the V-Y advancement flap and other local flaps, understand its geometry, and analyze its clinical applications. The analysis was based on qualitative measurements of an injury, taking into consideration the following dimensions: largest diameter, shortest diameter, and depth. Standardization of the flap design consisted of directing its advancement over the shortest diameter and making the V base match the size of the largest diameter. The flap was analyzed in two planes: the horizontal plane includes the V-Y design and the vertical plane includes the flap pedicle. The height of the flap can be obtained by simple trigonometry, taking into consideration the largest diameter and alpha angle in the horizontal plane. In the vertical plane, where the pedicle and pivot plane are positioned, for known shortest diameter and depth, the final depth of the pivot plane can be calculated using Pythagoras' principles. This analysis was applied to 25 patients with adequate skin coverage at follow-up. A correction factor was added to reduce the overdeepening of the vertical plane calculations. The final concepts for clinical application in the classic deep pedicle V-Y flap design are to calculate the length of the V by modifying the alpha angle and to move the pivot plane deeper to accomplish optimal flap movement. Using these principles, tension-free closure of the Y and appropriate advancement of the flap are obtained.

Uplift and subsidence associated with the great Aceh-Andaman earthquake of 2004

USGS Publications Warehouse

Meltzner, A.J.; Sieh, K.; Abrams, M.; Agnew, D.C.; Hudnut, K.W.; Avouac, J.-P.; Natawidjaja, D.H.

2006-01-01

Rupture of the Sunda megathrust on 26 December 2004 produced broad regions of uplift and subsidence. We define the pivot line separating these regions as a first step in defining the lateral extent and the downdip limit of rupture during that great Mw ??? 9.2 earthquake. In the region of the Andaman and Nicobar islands we rely exclusively on the interpretation of satellite imagery and a tidal model. At the southern limit of the great rupture we rely principally on field measurements of emerged coral microatolls. Uplift extends from the middle of Simeulue Island, Sumatra, at ??? 2.5??N, to Preparis Island, Myanmar (Burma), at ??? 14.9??N. Thus the rupture is ??? 1600 km long. The distance from the pivot line to the trench varies appreciably. The northern and western Andaman Islands rose, whereas the southern and eastern portion of the islands subsided. The Nicobar Islands and the west coast of Aceh province, Sumatra, subsided. Tilt at the southern end of the rupture is steep; the distance from 1.5 m of uplift to the pivot line is just 60 km. Our method of using satellite imagery to recognize changes in elevation relative to sea surface height and of using a tidal model to place quantitative bounds on coseismic uplift or subsidence is a novel approach that can be adapted to other forms of remote sensing and can be applied to other subduction zones in tropical regions. Copyright 2006 by the American Geophysical Union.

The Effect of Working Position on Trunk Posture and Exertion for Routine Nursing Tasks: An Experimental Study

PubMed Central

Freitag, Sonja

2014-01-01

Objectives: To examine the influence of the two following factors on the proportion of time that nurses spend in a forward-bending trunk posture: (i) the bed height during basic care activities at the bedside and (ii) the work method during basic care activities in the bathroom. A further aim was to examine the connection between the proportion of time spent in a forward-bending posture and the perceived exertion. Methods: Twelve nurses in a geriatric nursing home each performed a standardized care routine at the bedside and in the bathroom. The CUELA (German abbreviation for ‘computer-assisted recording and long-term analysis of musculoskeletal loads’) measuring system was used to record all trunk inclinations. Each participant conducted three tests with the bed at different heights (knee height, thigh height, and hip height) and in the bathroom, three tests were performed with different work methods (standing, kneeling, and sitting). After each test, participants rated their perceived exertion on the 15-point Borg scale (6 = no exertion at all and 20 = exhaustion). Results: If the bed was raised from knee to thigh level, the proportion of time spent in an upright position increased by 8.2% points. However, the effect was not significant (P = 0.193). Only when the bed was raised to hip height, there was a significant increase of 19.8% points (reference: thigh level; P = 0.003) and 28.0% points (reference: knee height; P < 0.001). Bathroom tests: compared with the standing work method, the kneeling and sitting work methods led to a significant increase in the proportion of time spent in an upright posture, by 19.4% points (P = 0.003) and 25.7% points (P < 0.001), respectively. The greater the proportion of time spent in an upright position, the lower the Borg rating (P < 0.001) awarded. Conclusions: The higher the proportion of time that nursing personnel work in an upright position, the less strenuous they perceive the work to be. Raising the bed to hip height and using a stool in the bathroom significantly increase the proportion of time that nursing personnel work in an upright position. Nursing staff can spend a considerably greater proportion of their time in an ergonomic posture if stools and height-adjustable beds are provided in healthcare institutions. PMID:24371043

The effect of working position on trunk posture and exertion for routine nursing tasks: an experimental study.

PubMed

Freitag, Sonja; Seddouki, Rachida; Dulon, Madeleine; Kersten, Jan Felix; Larsson, Tore J; Nienhaus, Albert

2014-04-01

To examine the influence of the two following factors on the proportion of time that nurses spend in a forward-bending trunk posture: (i) the bed height during basic care activities at the bedside and (ii) the work method during basic care activities in the bathroom. A further aim was to examine the connection between the proportion of time spent in a forward-bending posture and the perceived exertion. Twelve nurses in a geriatric nursing home each performed a standardized care routine at the bedside and in the bathroom. The CUELA (German abbreviation for 'computer-assisted recording and long-term analysis of musculoskeletal loads') measuring system was used to record all trunk inclinations. Each participant conducted three tests with the bed at different heights (knee height, thigh height, and hip height) and in the bathroom, three tests were performed with different work methods (standing, kneeling, and sitting). After each test, participants rated their perceived exertion on the 15-point Borg scale (6 = no exertion at all and 20 = exhaustion). If the bed was raised from knee to thigh level, the proportion of time spent in an upright position increased by 8.2% points. However, the effect was not significant (P = 0.193). Only when the bed was raised to hip height, there was a significant increase of 19.8% points (reference: thigh level; P = 0.003) and 28.0% points (reference: knee height; P < 0.001). Bathroom tests: compared with the standing work method, the kneeling and sitting work methods led to a significant increase in the proportion of time spent in an upright posture, by 19.4% points (P = 0.003) and 25.7% points (P < 0.001), respectively. The greater the proportion of time spent in an upright position, the lower the Borg rating (P < 0.001) awarded. The higher the proportion of time that nursing personnel work in an upright position, the less strenuous they perceive the work to be. Raising the bed to hip height and using a stool in the bathroom significantly increase the proportion of time that nursing personnel work in an upright position. Nursing staff can spend a considerably greater proportion of their time in an ergonomic posture if stools and height-adjustable beds are provided in healthcare institutions.

Position-Related Differences in Selected Morphological Body Characteristics of Top-Level Female Handball Players.

PubMed

Bon, Marta; Pori, Primoz; Sibila, Marko

2015-09-01

The study aimed to establish the main morphological characteristics of Slovenian junior and senior female national handball team players. Morphological characteristics of various player subgroups (goalkeepers, wings, back players and pivots) were also determined so as to establish whether they had distinct profiles. The subjects were 87 handball players who were members of the Slovenian junior and senior female national teams in the period from 2003 to 2009. A standardised anthropometric protocol was used to assess the subjects' morphological characteristics. The measurements included 23 different anthropometric measures. First, basic statistical characteristics of anthropometric measures were obtained for all subjects together and then for each group separately. Somatotypes were determined using Heath-Carter's method. Endomorphic, mesomorphic and ectomorphic components were calculated by computer on the basis of formulas. In order to determine differences in the body composition and anthropometric data of the subjects playing in different positions, a one-way analysis of variance was employed. The results show that, on average, the wings differed the most from the other player groups in terms of their morphological body characteristics. The wings differed most prominently from the other player groups in terms of their morphological body parameters as they were significantly smaller and had a statistically significantly lower body mass than the other groups. In terms of transversal measures of the skeleton and the circumferences, the wings significantly differed mainly from the pivots and goalkeepers and less from the backs. The goalkeepers were the tallest, with high values of body mass and low values of transversal measures compared to P. Their skin folds were the most pronounced among all the groups on average and their share of subcutaneous fat in total body mass was the highest. Consequently, their endomorphic component of the somatotype was pronounced. Players in the Pivot position were significantly taller than the Wplayers but were not significantly different from G and B. They had high values of body mass which were significantly higher than that of W but did not differ significantly from the body mass values of B and G. The average values of their circumferences were the highest among all the player groups and the same is true for transversal measures of the skeleton. It is very interesting that, compared to the players in other playing positions, they achieved low values of subcutaneous fat. Their values of the somatotype revealed an endo-mesomorphic somatotype, with a pronounced mesomorphic component. Back players were tall and had the lowest share of subcutaneous fat of all the player groups. Significant differences were established mainly in terms of the structure of the lower extremities. The values of the somato-type characteristics were very balanced between all three components. The results of our study confirm that groups of handball players occupying different positions differed amongst themselves in terms of many measurements. This is a result of the specific requirements of handball play which are to be met by particular players. The tallest players should thus be oriented to back player positions. As regards pivots, the coaches must, besides body height, consider robustness. For goal-keepers, body height is very important; however, the robustness criteria are slightly lower. For wings, body height is not a decisive factor and smaller players can also occupy this position. Both of the above (also taking other criteria into account) facilitate coaches' decisions when orienting players into their playing positions.

F-35 program accelerating, at 'pivot point,' program chief tells Congress >

Science.gov Websites

the CMSAF The Book Speeches Archive Former AF Top 3 Viewpoints and Speeches Air Force Warrior Games Games Portraits in Courage Portraits In Courage Vol. I Portraits In Courage Vol. II Portraits In Courage

Sustainability: What Is the Trustee's Stake?

ERIC Educational Resources Information Center

Pelletier, Stephen

2008-01-01

Sustainability has become a central consideration across the board in university business decisions. Passing a tipping point, it has become a pivotal focus of management. College leaders are increasingly drawing connections between sustainability, institutional missions, and higher education's fundamental purposes. Administrators readily rattle…

Structural Consequences of Hydrogen Intercalation of Epitaxial Graphene on SiC(0001)

DTIC Science & Technology

2014-10-23

in barrier height at the graphene –silicon carbide Schottky junction,” Nat. Commun. 4, 2752 (2013). 31H. Yang, J. Heo, S. Park, H. J. Song, D. H. Seo, K...displacement. The shift of the Dirac point defines the Schottky barrier height and will determine the practicality of employing the wide-bandgap...are thought to critically influence technologi- cally relevant properties such as Dirac point shift and Schottky barrier height . Furthermore, this

The Influence of the Solar Coronal Radiation on Coronal Plasma Structures, I: Determination of the Incident Coronal Radiation

NASA Astrophysics Data System (ADS)

Brown, Gerrard M.; Labrosse, Nicolas

2018-02-01

Coronal structures receive radiation not only from the solar disc, but also from the corona. This height-dependent incident radiation plays a crucial role in the excitation and the ionisation of the illuminated plasma. The aim of this article is to present a method for computing the detailed incident radiation coming from the solar corona, which is perceived at a point located at an arbitrary height. The coronal radiation is calculated by integrating the radiation received at a point in the corona over all of the corona visible from this point. The emission from the corona at all wavelengths of interest is computed using atomic data provided by CHIANTI. We obtain the spectrum illuminating points located at varying heights in the corona at wavelengths between 100 and 912 Å when photons can ionise H or He atoms and ions in their ground states. As expected, individual spectral lines will contribute most at the height within the corona where the local temperature is closest to their formation temperature. As there are many spectral lines produced by many ions, the coronal intensity cannot be assumed to vary in the same way at all wavelengths and so must be calculated for each separate height that is to be considered. This code can be used to compute the spectrum from the corona illuminating a point at any given height above the solar surface. This brings a necessary improvement to models where an accurate determination of the excitation and ionisation states of coronal plasma structures is crucial.

Features of Point Clouds Synthesized from Multi-View ALOS/PRISM Data and Comparisons with LiDAR Data in Forested Areas

NASA Technical Reports Server (NTRS)

Ni, Wenjian; Ranson, Kenneth Jon; Zhang, Zhiyu; Sun, Guoqing

2014-01-01

LiDAR waveform data from airborne LiDAR scanners (ALS) e.g. the Land Vegetation and Ice Sensor (LVIS) havebeen successfully used for estimation of forest height and biomass at local scales and have become the preferredremote sensing dataset. However, regional and global applications are limited by the cost of the airborne LiDARdata acquisition and there are no available spaceborne LiDAR systems. Some researchers have demonstrated thepotential for mapping forest height using aerial or spaceborne stereo imagery with very high spatial resolutions.For stereo imageswith global coverage but coarse resolution newanalysis methods need to be used. Unlike mostresearch based on digital surface models, this study concentrated on analyzing the features of point cloud datagenerated from stereo imagery. The synthesizing of point cloud data from multi-view stereo imagery increasedthe point density of the data. The point cloud data over forested areas were analyzed and compared to small footprintLiDAR data and large-footprint LiDAR waveform data. The results showed that the synthesized point clouddata from ALOSPRISM triplets produce vertical distributions similar to LiDAR data and detected the verticalstructure of sparse and non-closed forests at 30mresolution. For dense forest canopies, the canopy could be capturedbut the ground surface could not be seen, so surface elevations from other sourceswould be needed to calculatethe height of the canopy. A canopy height map with 30 m pixels was produced by subtracting nationalelevation dataset (NED) fromthe averaged elevation of synthesized point clouds,which exhibited spatial featuresof roads, forest edges and patches. The linear regression showed that the canopy height map had a good correlationwith RH50 of LVIS data with a slope of 1.04 and R2 of 0.74 indicating that the canopy height derived fromPRISM triplets can be used to estimate forest biomass at 30 m resolution.

Serum growth hormone (GH)-binding protein/receptor: an important determinant of GH responsiveness.

PubMed

Martha, P M; Reiter, E O; Dávila, N; Shaw, M A; Holcombe, J H; Baumann, G

1992-12-01

Individual growth rates (or responses to GH therapy) and adult heights vary over a wide range. The reasons for this variation are poorly understood. Based on the reciprocal relationship between GH production and serum GH-binding protein/receptor (GH-BP), we hypothesized that genetic growth potential was achieved by a specific combination of GH-BP/receptor and GH production in each individual. To address the question whether GH production regulates GH-BP, or vice versa, we studied GH-deficient children, where one of the parameters, GH exposure, could be controlled through exogenous administration. Forty-three untreated prepubertal GH-deficient children were studied before and after 6 and 12 months of GH replacement therapy (0.18 mg/kg.week). Growth velocity, height, bone age, weight and their respective Z scores, serum GH-BP, and serum insulin-like growth factor I (IGF-I) were measured at each time point. The patients responded with significant increases in serum IGF-I, age-adjusted growth velocity, and height (P < 10(-6) for all). Before therapy, GH-BP correlated directly with chronologic and bone age (P < 10(-4), but not with either growth velocity or IGF-I. In contrast, GH-BP correlated strongly with the response to therapy whether assessed as the incremental change in IGF-I (P < 10(-6)) or as the increase in growth velocity (P approximately 0.003). GH treatment had no consistent effect on GH-BP/receptor levels. These findings support the concept that the GH-BP/receptor endowment is characteristic for an individual and plays a pivotal role in somatic growth. The GH-BP/receptor system and its ontogeny appears relatively independent of regulation by GH. Differences in individual GH-BP/GH receptor complement account for some of the variability in the response to GH, and GH-BP levels may serve as a predictor for the degree of response. The reciprocal relationship between GH production and GH-BP in normal subjects probably results from adjustment of GH secretion to accommodate the prevailing GH-BP/receptor environment.

Interactive Mechanisms of Sliding-Surface Bearings.

DTIC Science & Technology

1983-08-01

lower, upper) bearing surface V Three-dimensional gradient operator ix Two-dimensional surface gradient operator ( ),. Pertaining to the bearing surface...thermal gradients . The tilt-pad feature required the pad inclination to be determined by the condition of moment equilibrium about the pivot point. This...into the computation of pressure and shear in a fluid film. Incipience Point of Film Rupture On page 93 of Appendix A, pressure gradient and pressure of

Reaching Higher Goals by Means of a Reflecting Wall

ERIC Educational Resources Information Center

Faella, Orazio; De Luca, Roberto

2015-01-01

A student realizes that a point particle that is able to rise at a given point P[subscript 0] at height H when launched vertically from the origin O of a Cartesian plane at a fixed initial speed V[subscript 0] cannot reach, by means of a direct shot from a small spring cannon, a point P positioned at the same height H and distance d from…

Curvature facilitates prey fixation in predatory insect claws.

PubMed

Petie, Ronald; Muller, Mees

2007-02-21

Insects show a large variety in prey capture strategies, with a correspondingly large diversity in predatory adaptations. We studied a specific type of predatory claws, these can for example be found in praying mantis species. The claw is closeable over its entire length and the prey is fixed between the femur (upper arm) and the tibia (lower arm) of the insect leg. The morphology of these predatory claws is diverse. Some species have straight claws covered with spines, while other species have smooth, curved claws. We have studied the mechanics of this femur-tibia type of predatory insect claws, by making a physical model, eventually trying to explain why in some insect species the claws are curved instead of straight. The main results are (1) when comparing curved claws to straight claws, curvature leads to a strong reduction of forces driving the prey away from the pivoting point, thereby reducing the need for friction generating structures. (2) In the curved claw model a position exists where the resulting force on the prey is exactly zero. This is because the normal forces on the femur and tibia are opposed, and in line. At this position the prey is perfectly clamped and not driven out of the claw. This feature does not exist in straight claws. (3) In the curved claw, the prey cannot be placed at a position further than a certain maximum distance from the pivoting point. Near this maximum position, the resulting force on the prey reaches high values because moment arms are near zero. (4) Between the zero position and the maximum position the resulting force is directed toward the pivoting point, which stabilizes prey fixation.

Possible options to slow down the advancement rate of Tarbela delta.

PubMed

Habib-Ur-Rehman; Rehman, Mirza Abdul; Naeem, Usman Ali; Hashmi, Hashim Nisar; Shakir, Abdul Sattar

2017-12-22

The pivot point of delta in Tarbela dam has reached at about 10.6 km from the dam face which may result in blocking of tunnels. Tarbela delta was modeled from 1979 to 2060 using hec-6 model. Initially, the model was calibrated for year 1999 and validated for years 2000, 2001, 2002, and 2006 by involving the data of sediment concentration, reservoir cross sections (73 range lines), elevation-area capacity curves, and inflows and outflows from the reservoir. Then, the model was used to generate future scenarios, i.e., run-1, run-2, and run-3 with pool levels; 428, 442, and 457 m, respectively, till 2060. Results of run-1 and run-2 showed advancement to choke the tunnels by 2010 and 2030, respectively. Finally, in run-3, the advancement was further delayed showing that tunnels 1 and 2 will be choked by year 2050 and pivot point will reach at 6.4 km from the dam face.

Co-management as a Catalyst: Pathways to Post-colonial Forestry in the Klamath Basin, California.

PubMed

Diver, Sibyl

2016-01-01

Co-management frameworks are intended to facilitate sustainable resource management and more equitable power sharing between state agencies and Indigenous communities. However, there is significant debate about who benefits from co-management in practice. This article addresses two competing perspectives in the literature, which alternately portrays co-management as an instrument for co-optation or for transformation. Through a case study of co-management negotiations involving the Karuk Tribe and the U.S. Forest Service in the Klamath Basin of Northern California, this study examines how Indigenous communities use co-management to build greater equity in environmental decision-making, despite its limitations. The concept of pivot points is developed to describe how Indigenous communities like the Karuk Tribe are simultaneously following existing state policies and subverting them to shift federal forest management. The pivot point analytic demonstrates one mechanism by which communities are addressing Indigenous self-determination goals and colonial legacies through environmental policy and management.

33 CFR 183.110 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., below a height of 4 inches measured from the lowest point in the boat where liquid can collect when the boat is in its static floating position, except engine rooms. Connected means allowing a flow of water... the engine room or a connected compartment below a height of 12 inches measured from the lowest point...

33 CFR 177.07 - Other unsafe conditions.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) The wave height within the Regulated Boating Area is 4 feet or greater; or (2) The wave height within the Regulated Boating Area is equal to or greater than the wave height determined by the formula L/10... from the lowest point along the upper strake edge to the surface of the water. W=Maximum wave height in...

33 CFR 177.07 - Other unsafe conditions.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) The wave height within the Regulated Boating Area is 4 feet or greater; or (2) The wave height within the Regulated Boating Area is equal to or greater than the wave height determined by the formula L/10... from the lowest point along the upper strake edge to the surface of the water. W=Maximum wave height in...

33 CFR 177.07 - Other unsafe conditions.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) The wave height within the Regulated Boating Area is 4 feet or greater; or (2) The wave height within the Regulated Boating Area is equal to or greater than the wave height determined by the formula L/10... from the lowest point along the upper strake edge to the surface of the water. W=Maximum wave height in...

An examination of the jump-and-lift factors influencing the time to reach peak catch height during a Rugby Union lineout.

PubMed

Smith, Tiaki Brett; Hébert-Losier, Kim; McClymont, Doug

2018-05-01

The goal of an offensive Rugby Union lineout is to throw the ball in a manner that allows your team to maintain possession. Typically, the player catching the ball jumps and is lifted upwards by two teammates, reaching above the opposing player who is competing for the ball also. Despite various beliefs regarding the importance of the jumper's mass and attempted jump height, and lifters' magnitude and point of force application, there is negligible published data on the topic. The squeeze technique is one lifting method commonly employed by New Zealand teams during lineout plays, whereby the jumper initiates the jump quickly and the lifters provide assistance only once the jumper reaches 20-30 cm. While this strategy may reduce cues to the opposition, it might also constrain the jumper and lifters. We developed a model to explore how changes in the jumper's body mass and attempted jump height, and lifters' magnitude and point of force application influence the time to reach peak catch height. The magnitude of the lift force impacted the time-to-reach peak catch height the most; followed by the jumper's (attempted) jump height and body mass; and lastly, the point of lift force application.

Rethinking Terrestrial Pedagogy: Nature, Cultures, and Ethics

ERIC Educational Resources Information Center

Li, Huey-Li

2006-01-01

In this article, I offer a clarification of the ambiguities surrounding the pivotal concepts that have shaped and will continue to shape environmental education movement in the United States and beyond: nature, conservation, sustainable development, and environmental justice. I point out that dualistic frameworks not only polarize environmental…

Environmental Education and Geography of Complexity

ERIC Educational Resources Information Center

Cecioni, Ester

2005-01-01

Geography is defined as "a transition point between natural temporality and human temporality" (Maragliano, 1998). Presented like this, geography seems, at least at first sight, to assume an inexorable function as a linking discipline between nature and society. Unfortunately this pivotal role is not realised, given that geography is…

Continuing Education for Business. Monograph 134.

ERIC Educational Resources Information Center

Cooley, Max G.

Designed to review the changing pattern of adult education, this monograph focuses attention on the current situation and pivotal points of change confronting business educators. A discussion of philosophical foundations in adult education for business in chapter 1 provides definitions and discusses transition in adult education and importance of…

More practical critical height sampling.

Treesearch

Thomas B. Lynch; Jeffrey H. Gove

2015-01-01

Critical Height Sampling (CHS) (Kitamura 1964) can be used to predict cubic volumes per acre without using volume tables or equations. The critical height is defined as the height at which the tree stem appears to be in borderline condition using the point-sampling angle gauge (e.g. prism). An estimate of cubic volume per acre can be obtained from multiplication of the...

Ultra-low-frequency vertical vibration isolator based on a two-stage beam structure for absolute gravimetry.

PubMed

Wang, G; Wu, K; Hu, H; Li, G; Wang, L J

2016-10-01

To reduce seismic and environmental vibration noise, ultra-low-frequency vertical vibration isolation systems play an important role in absolute gravimetry. For this purpose, an isolator based on a two-stage beam structure is proposed and demonstrated. The isolator has a simpler and more robust structure than the present ultra-low-frequency vertical active vibration isolators. In the system, two beams are connected to a frame using flexural pivots. The upper beam is suspended from the frame with a normal hex spring and the lower beam is suspended from the upper one using a zero-length spring. The pivot of the upper beam is not vertically above the pivot of the lower beam. With this special design, the attachment points of the zero-length spring to the beams can be moved to adjust the effective stiffness. A photoelectric detector is used to detect the angle between the two beams, and a voice coil actuator attached to the upper beam is controlled by a feedback circuit to keep the angle at a fixed value. The system can achieve a natural period of 100 s by carefully moving the attachment points of the zero-length spring to the beams and tuning the feedback parameters. The system has been used as an inertial reference in the T-1 absolute gravimeter. The experiment results demonstrate that the system has significant vibration isolation performance that holds promise in applications such as absolute gravimeters.

Ultra-low-frequency vertical vibration isolator based on a two-stage beam structure for absolute gravimetry

NASA Astrophysics Data System (ADS)

Wang, G.; Wu, K.; Hu, H.; Li, G.; Wang, L. J.

2016-10-01

To reduce seismic and environmental vibration noise, ultra-low-frequency vertical vibration isolation systems play an important role in absolute gravimetry. For this purpose, an isolator based on a two-stage beam structure is proposed and demonstrated. The isolator has a simpler and more robust structure than the present ultra-low-frequency vertical active vibration isolators. In the system, two beams are connected to a frame using flexural pivots. The upper beam is suspended from the frame with a normal hex spring and the lower beam is suspended from the upper one using a zero-length spring. The pivot of the upper beam is not vertically above the pivot of the lower beam. With this special design, the attachment points of the zero-length spring to the beams can be moved to adjust the effective stiffness. A photoelectric detector is used to detect the angle between the two beams, and a voice coil actuator attached to the upper beam is controlled by a feedback circuit to keep the angle at a fixed value. The system can achieve a natural period of 100 s by carefully moving the attachment points of the zero-length spring to the beams and tuning the feedback parameters. The system has been used as an inertial reference in the T-1 absolute gravimeter. The experiment results demonstrate that the system has significant vibration isolation performance that holds promise in applications such as absolute gravimeters.

Comparisons of chewing rhythm, craniomandibular morphology, body mass and height between mothers and their biological daughters.

PubMed

Cho, Catherine; Louie, Ke'ale; Maawadh, Ahmed; Gerstner, Geoffrey E

2015-11-01

To study and compare the relationships between mean chewing cycle duration, selected cephalometric variables representing mandibular length, face height, etc., measured in women and in their teenage or young-adult biological daughters. Daughters were recruited from local high schools and the University of Michigan School of Dentistry. Selection criteria included healthy females with full dentition, 1st molar occlusion, no active orthodontics, no medical conditions nor medication use that could interfere with normal masticatory motor function. Mothers had to be biologically related to their daughters. All data were obtained in the School of Dentistry. Measurements obtained from lateral cephalograms included: two "jaw length" measures, condylion-gnathion and gonion-gnathion, and four measures of facial profile including lower anterior face height, and angles sella-nasion-A point (SNA), sella-nasion-B point (SNB) and A point-nasion-B point (ANB). Mean cycle duration was calculated from 60 continuous chewing cycles, where a cycle was defined as the time between two successive maximum jaw openings in the vertical dimension. Other variables included subject height and weight. Linear and logistic regression analyses were used to evaluate the mother-daughter relationships and to study the relationships between cephalometric variables and chewing cycle duration. Height, weight, Co-Gn and Go-Gn were significantly correlated between mother-daughter pairs; however, mean cycle duration was not (r(2)=0.015). Mean cycle duration was positively correlated with ANB and height in mothers, but negatively correlated with Co-Gn in daughters. Chewing rate is not correlated between mothers and daughters in humans. Copyright © 2015 Elsevier Ltd. All rights reserved.

Assessing and Correcting Topographic Effects on Forest Canopy Height Retrieval Using Airborne LiDAR Data

PubMed Central

Duan, Zhugeng; Zhao, Dan; Zeng, Yuan; Zhao, Yujin; Wu, Bingfang; Zhu, Jianjun

2015-01-01

Topography affects forest canopy height retrieval based on airborne Light Detection and Ranging (LiDAR) data a lot. This paper proposes a method for correcting deviations caused by topography based on individual tree crown segmentation. The point cloud of an individual tree was extracted according to crown boundaries of isolated individual trees from digital orthophoto maps (DOMs). Normalized canopy height was calculated by subtracting the elevation of centres of gravity from the elevation of point cloud. First, individual tree crown boundaries are obtained by carrying out segmentation on the DOM. Second, point clouds of the individual trees are extracted based on the boundaries. Third, precise DEM is derived from the point cloud which is classified by a multi-scale curvature classification algorithm. Finally, a height weighted correction method is applied to correct the topological effects. The method is applied to LiDAR data acquired in South China, and its effectiveness is tested using 41 field survey plots. The results show that the terrain impacts the canopy height of individual trees in that the downslope side of the tree trunk is elevated and the upslope side is depressed. This further affects the extraction of the location and crown of individual trees. A strong correlation was detected between the slope gradient and the proportions of returns with height differences more than 0.3, 0.5 and 0.8 m in the total returns, with coefficient of determination R2 of 0.83, 0.76, and 0.60 (n = 41), respectively. PMID:26016907

58. VIEW OF SOUTHWEST SIDE OF LAUNCHER FROM ABOVE. AFRAME ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

58. VIEW OF SOUTHWEST SIDE OF LAUNCHER FROM ABOVE. A-FRAME PIVOT POINT IN CENTER OF PHOTOGRAPH; NITROGEN CONTROL UNIT IN UPPER LEFT CORNER OF PHOTOGRAPH. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

Miscarriage: A Dream Interrupted

ERIC Educational Resources Information Center

Trepal, Heather C.; Semivan, Suzanne Gibson; Caley-Bruce, Mary

2005-01-01

Pregnancy is a developmental task that requires women to become accustomed to inherent and sometimes profound biological, somatic, and psychological changes. When pregnancy is interrupted by miscarriage, it may become a pivotal crisis point in the development of a woman's maternal identity as well as an issue in family development. This manuscript…

78 FR 58978 - Airworthiness Directives; Airbus Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-25

... during low speed taxi maneuvers. The bogie fractured aft of the pivot point and remained attached to the sliding tube by the brake torque reaction rods. After this RH bogie failure, the aeroplane continued for... requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in...

Heterogeneity of Student Perceptions of the Classroom Climate: A Latent Profile Approach

ERIC Educational Resources Information Center

Schenke, Katerina; Ruzek, Erik; Lam, Arena C.; Karabenick, Stuart A.; Eccles, Jacquelynne S.

2017-01-01

Student perceptions are a pivotal point of measurement for understanding why classroom learning environments are effective. Yet there is some evidence that student perceptions cannot be reliably aggregated at the classroom level and, instead, could represent idiosyncratic experiences of students. The present study examines whether heterogeneity in…

Critical Thinking in Nurse Anesthesia Education: A Pilot Study

ERIC Educational Resources Information Center

Burns, Shari; Mendel, Shaun; Fisher, Rodney; Cooper, Kimball; Fisher, Michael

2013-01-01

Critical thinking is pivotal for student success in health professions education. Knowing the critical thinking ability of the learner helps educators tailor curriculum to enhance critical thinking. A quantitative comparative pilot study assessed critical thinking ability for students at two distinct points in a nurse anesthesia program…

Outfoxing the Hedgehog

ERIC Educational Resources Information Center

Barbieri, Richard

2011-01-01

Jim Collins's "Good to Great" has attained near-scriptural status in organizations, including nonprofits, which Collins says constitute a third of his readers. The pivot point in "Good to Great" is the Hedgehog Concept. The "Hedgehog Concept" (HC), this author claims, is dangerous for schools because it distorts the nature of education. As Collins…

Linear kinematic air bearing

NASA Technical Reports Server (NTRS)

Mayall, S. D.

1974-01-01

Bearing provides continuous, smooth movement of the cat's-eye mirror, eliminating wear and deterioration of bearing surface and resulting oscillation effects in servo system. Design features self-aligning configuration; single-point, pivotal pad mounting, having air passage through it; and design of pads that allows for precise control of discharge path of air from pads.

First NAC Image Obtained in Mercury Orbit

NASA Image and Video Library

2017-12-08

NASA image acquired: March 29, 2011 This is the first image of Mercury taken from orbit with MESSENGER’s Narrow Angle Camera (NAC). MESSENGER’s camera system, the Mercury Dual Imaging System (MDIS), has two cameras: the Narrow Angle Camera and the Wide Angle Camera (WAC). Comparison of this image with MESSENGER’s first WAC image of the same region shows the substantial difference between the fields of view of the two cameras. At 1.5°, the field of view of the NAC is seven times smaller than the 10.5° field of view of the WAC. This image was taken using MDIS’s pivot. MDIS is mounted on a pivoting platform and is the only instrument in MESSENGER’s payload capable of movement independent of the spacecraft. The other instruments are fixed in place, and most point down the spacecraft’s boresight at all times, relying solely on the guidance and control system for pointing. The 90° range of motion of the pivot gives MDIS a much-needed extra degree of freedom, allowing MDIS to image the planet’s surface at times when spacecraft geometry would normally prevent it from doing so. The pivot also gives MDIS additional imaging opportunities by allowing it to view more of the surface than that at which the boresight-aligned instruments are pointed at any given time. On March 17, 2011 (March 18, 2011, UTC), MESSENGER became the first spacecraft ever to orbit the planet Mercury. The mission is currently in the commissioning phase, during which spacecraft and instrument performance are verified through a series of specially designed checkout activities. In the course of the one-year primary mission, the spacecraft's seven scientific instruments and radio science investigation will unravel the history and evolution of the Solar System's innermost planet. Visit the Why Mercury? section of this website to learn more about the science questions that the MESSENGER mission has set out to answer. Credit: NASA/Johns Hopkins University Applied Physics Laboratory/Carnegie Institution of Washington NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Join us on Facebook

Global Forest Canopy Height Maps Validation and Calibration for The Potential of Forest Biomass Estimation in The Southern United States

NASA Astrophysics Data System (ADS)

Ku, N. W.; Popescu, S. C.

2015-12-01

In the past few years, three global forest canopy height maps have been released. Lefsky (2010) first utilized the Geoscience Laser Altimeter System (GLAS) on the Ice, Cloud and land Elevation Satellite (ICESat) and Moderate Resolution Imaging Spectroradiometer (MODIS) data to generate a global forest canopy height map in 2010. Simard et al. (2011) integrated GLAS data and other ancillary variables, such as MODIS, Shuttle Radar Topography Mission (STRM), and climatic data, to generate another global forest canopy height map in 2011. Los et al. (2012) also used GLAS data to create a vegetation height map in 2012.Several studies attempted to compare these global height maps to other sources of data., Bolton et al. (2013) concluded that Simard's forest canopy height map has strong agreement with airborne lidar derived heights. Los map is a coarse spatial resolution vegetation height map with a 0.5 decimal degrees horizontal resolution, around 50 km in the US, which is not feasible for the purpose of our research. Thus, Simard's global forest canopy height map is the primary map for this research study. The main objectives of this research were to validate and calibrate Simard's map with airborne lidar data and other ancillary variables in the southern United States. The airborne lidar data was collected between 2010 and 2012 from: (1) NASA LiDAR, Hyperspectral & Thermal Image (G-LiHT) program; (2) National Ecological Observatory Network's (NEON) prototype data sharing program; (3) NSF Open Topography Facility; and (4) the Department of Ecosystem Science and Management at Texas A&M University. The airborne lidar study areas also cover a wide variety of vegetation types across the southern US. The airborne lidar data is post-processed to generate lidar-derived metrics and assigned to four different classes of point cloud data. The four classes of point cloud data are the data with ground points, above 1 m, above 3 m, and above 5 m. The root mean square error (RMSE) and coefficient of determination (R2) are used for examining the discrepancies of the canopy heights between the airborne lidar-derived metrics and global forest canopy height map, and the regression and random forest approaches are used to calibrate the global forest canopy height map. In summary, the research shows a calibrated forest canopy height map of the southern US.

The stature of the self-employed and its relation with earnings and satisfaction.

PubMed

Rietveld, Cornelius A; Hessels, Jolanda; van der Zwan, Peter

2015-04-01

Taller individuals have on average a higher socio-economic status than shorter individuals. In countries where entrepreneurs have high social status, we may therefore expect that entrepreneurs are taller than wage workers. Using data from the German Socio-Economic Panel (2002-2012), we find that a 1cm increase in an individual's height raises the probability of being self-employed (the most common proxy for entrepreneurship) versus paid employed by 0.15 percentage points. Within the self-employed, the probability of being an employer is increased by 0.10 percentage points as a result of a 1cm increase in height, whereas this increase is 0.05 percentage points for an own-account worker. This result corroborates the higher social status of employers compared to own-account workers. We find a height premium in earnings for self-employed and paid-employed individuals: an additional 1cm in height is associated with a 0.39% increase in hourly earnings for paid employees and a 0.52% increase for self-employed individuals. Our analysis reveals that approximately one third of the height premium in earnings is explained by differences in educational attainment. We also establish the existence of a height premium in terms of work and life satisfaction, which is more pronounced for paid employees than for self-employed individuals. Copyright © 2015 Elsevier B.V. All rights reserved.

Multi-access laser communications transceiver system

NASA Technical Reports Server (NTRS)

Ross, Monte (Inventor); Lokerson, Donald C. (Inventor); Fitzmaurice, Michael W. (Inventor); Meyer, Daniel D. (Inventor)

1993-01-01

A satellite system for optical communications such as a multi-access laser transceiver system. Up to six low Earth orbiting satellites send satellite data to a geosynchronous satellite. The data is relayed to a ground station at the Earth's surface. The earth pointing geosynchronous satellite terminal has no gimbal but has a separate tracking mechanism for tracking each low Earth orbiting satellite. The tracking mechanism has a ring assembly rotatable about an axis coaxial with the axis of the field of view of the geosynchronous satellite and a pivotable arm mounted for pivotal movement on the ring assembly. An optical pickup mechanism at the end of each arm is positioned for optical communication with one of the orbiting satellites by rotation of the ring.

Clinical Evidence Supporting US Food and Drug Administration Premarket Approval of High-Risk Otolaryngologic Devices, 2000-2014.

PubMed

Rathi, Vinay K; Wang, Bo; Ross, Joseph S; Downing, Nicholas S; Kesselheim, Aaron S; Gray, Stacey T

2017-02-01

The US Food and Drug Administration (FDA) approves high-risk medical devices based on premarket pivotal clinical studies demonstrating reasonable assurance of safety and effectiveness and may require postapproval studies (PAS) to further inform benefit-risk assessment. We conducted a cross-sectional analysis using publicly available FDA documents to characterize industry-sponsored pivotal studies and PAS of high-risk devices used in the treatment of otolaryngologic diseases. Between 2000 and 2014, the FDA approved 23 high-risk otolaryngologic devices based on 28 pivotal studies. Median enrollment was 118 patients (interquartile range, 67-181), and median duration of longest primary effectiveness end point follow-up was 26 weeks (interquartile range, 16-96). Fewer than half were randomized (n = 13, 46%), blinded (n = 12, 43%), or controlled (n = 10, 36%). The FDA required 23 PASs for 16 devices (70%): almost two-thirds (n = 15, 65%) monitored long-term performance, and roughly one-third (n = 8, 35%) focused on subgroups. Otolaryngologists should be aware of limitations in the strength of premarket evidence when considering the use of newly approved devices.

Aeroelastic character of a National Aerospace Plane demonstrator concept

NASA Technical Reports Server (NTRS)

Spain, Charles V.; Zeiler, Thomas A.; Gibbons, Michael D.; Soistmann, David L.; Pozefsky, Peter; Dejesus, Rafael O.; Brannon, Cyprian P.

1993-01-01

The paper provides an analytical assessment of the flutter character of an unclassified National Aerospace Plane configuration known as the demonstrator. Linear subsonic, supersonic, and hypersonic analysis indicate that the vehicle is prone to body-freedom flutter resulting from the decrease in vibration frequency of the all-moveable wing at high flight dynamic pressures. As the wing-pivot frequency decreases, it couples with the vehicle short-period mode resulting in dynamic instability. A similar instability sometimes occurs when the pivot mode couples with the fuselage-bending mode. Also assessed, for supersonic flight conditions, are configuration variations that include relocation of the wing further aft on the lifting-body fuselage, and the addition of body flaps to the rear of the vehicle. These changes are destabilizing because they result in severe wing-pivot/fuselage-bending instabilities at dynamic pressures lower than the instabilities indicated for the original demonstrator. Finally, a two-point wing support and actuation system concept is proposed for the National Aerospace Plane, which if developed may (according to cursory analysis) enhance overall stability.

Evaluation of a new approach to compute intervertebral disc height measurements from lateral radiographic views of the spine.

PubMed

Allaire, Brett T; DePaolis Kaluza, M Clara; Bruno, Alexander G; Samelson, Elizabeth J; Kiel, Douglas P; Anderson, Dennis E; Bouxsein, Mary L

2017-01-01

Current standard methods to quantify disc height, namely distortion compensated Roentgen analysis (DCRA), have been mostly utilized in the lumbar and cervical spine and have strict exclusion criteria. Specifically, discs adjacent to a vertebral fracture are excluded from measurement, thus limiting the use of DCRA in studies that include older populations with a high prevalence of vertebral fractures. Thus, we developed and tested a modified DCRA algorithm that does not depend on vertebral shape. Participants included 1186 men and women from the Framingham Heart Study Offspring and Third Generation Multidetector CT Study. Lateral CT scout images were used to place 6 morphometry points around each vertebra at 13 vertebral levels in each participant. Disc heights were calculated utilizing these morphometry points using DCRA methodology and our modified version of DCRA, which requires information from fewer morphometry points than the standard DCRA. Modified DCRA and standard DCRA measures of disc height are highly correlated, with concordance correlation coefficients above 0.999. Both measures demonstrate good inter- and intra-operator reproducibility. 13.9 % of available disc heights were not evaluable or excluded using the standard DCRA algorithm, while only 3.3 % of disc heights were not evaluable using our modified DCRA algorithm. Using our modified DCRA algorithm, it is not necessary to exclude vertebrae with fracture or other deformity from disc height measurements as in the standard DCRA. Modified DCRA also yields identical measurements to the standard DCRA. Thus, the use of modified DCRA for quantitative assessment of disc height will lead to less missing data without any loss of accuracy, making it a preferred alternative to the current standard methodology.

SHOX haploinsufficiency and Leri-Weill dyschondrosteosis: prevalence and growth failure in relation to mutation, sex, and degree of wrist deformity.

PubMed

Binder, Gerhard; Renz, Alexandra; Martinez, Alicia; Keselman, Ana; Hesse, Volker; Riedl, Stefan W; Häusler, Gabriele; Fricke-Otto, Susanne; Frisch, Herwig; Heinrich, Juan Jorge; Ranke, Michael B

2004-09-01

SHOX mutations causing haploinsufficiency were reported in Leri-Weill dyschondrosteosis (LWD), which is characterized by mesomelic short stature and Madelung deformity of the wrists. The aim of this study was to determine the prevalence of SHOX mutations in LWD and to investigate the degree of growth failure in relation to mutation, sex, age of menarche, and wrist deformity. We studied 20 families with 24 affected children (18 females) and nine affected parents (seven females). All patients presented with bilateral Madelung deformity and shortening of the limbs. Height, sitting height, parental height, birth length, age of menarche, and presence of minor abnormalities were recorded. The degree of Madelung deformity was estimated by analysis of left hand radiographs. Microsatellite typing of the SHOX locus was used for detection of SHOX deletions and PCR direct sequencing for the detection of SHOX point mutations. In 14 of 20 families (70%), SHOX mutations were detected, with seven deletions (four de novo) and seven point mutations (one de novo). The latter included five missense mutations of the SHOX homeodomain, one nonsense mutation (E102X) truncating the whole homeodomain, and one point mutation (X293R) causing a C-terminal elongation of SHOX. Median age of the affected children was 13.4 yr (range, 6.1-18.3), mean height sd score (SDS) (sd in parentheses) was -2.85 (1.04), and mean sitting height/height ratio SDS was +3.06 (1.09). Mean birth length SDS was -0.59 (1.26). Growth failure occurred before school age. Height change during a median follow-up of 7.4 yr (range, 2.3-11.3) was insignificant with a mean change in height SDS of -0.10 (0.52). Mean height SDS of affected parents was -2.70 (0.85) vs. -0.91 (1.10) in unaffected parents. Height loss due to LWD was estimated calculating delta height defined by actual height SDS minus target height SDS of the unaffected parent(s). In the children, mean delta height SDS was -2.16 (1.06), the loss being greater in girls at -2.30 (1.02) than in boys at -1.72 (1.09) (P = 0.32). In patients with SHOX deletions, it was -2.14 (1.15) vs. -1.67 (0.73) for the SHOX point mutation group (P = 0.38). Mean delta height SDS was -2.26 (0.68) for the girls with early menarche (<12 yr) vs. -2.08 (0.91) for the other postmenarcheal girls (P = 0.72). Height loss in patients with radiologically severe wrist deformities in comparison with those having milder radiological signs was -2.81 (1.01) vs. -1.70 (1.04) (P = 0.03). GH treatment in five children during a median duration of 3.4 yr (range, 1.5-9.8 yr) with a median dosage of 0.23 mg/kg.wk (range, 0.14-0.25) resulted in a mean height SDS gain of +0.82 (0.34). In conclusion, SHOX defects were the main cause of LWD. Growth failure occurred during the first years of life with a mean height loss of 2.16 SDS whereas pubertal growth may only be mildly or not affected. Children with a severe degree of wrist deformity were significantly shorter than those with mild deformities. No statistically significant effects of type of mutation, age of menarche, or sex on height were observed. The effect of GH therapy varied between individuals and needs to be examined in controlled studies.

Hierarchical control of ride height system for electronically controlled air suspension based on variable structure and fuzzy control theory

NASA Astrophysics Data System (ADS)

Xu, Xing; Zhou, Kongkang; Zou, Nannan; Jiang, Hong; Cui, Xiaoli

2015-09-01

The current research of air suspension mainly focuses on the characteristics and design of the air spring. In fact, electronically controlled air suspension (ECAS) has excellent performance in flexible height adjustment during different driving conditions. However, the nonlinearity of the ride height adjusting system and the uneven distribution of payload affect the control accuracy of ride height and the body attitude. Firstly, the three-point measurement system of three height sensors is used to establish the mathematical model of the ride height adjusting system. The decentralized control of ride height and the centralized control of body attitude are presented to design the ride height control system for ECAS. The exact feedback linearization method is adopted for the nonlinear mathematical model of the ride height system. Secondly, according to the hierarchical control theory, the variable structure control (VSC) technique is used to design a controller that is able to adjust the ride height for the quarter-vehicle anywhere, and each quarter-vehicle height control system is independent. Meanwhile, the three-point height signals obtained by three height sensors are tracked to calculate the body pitch and roll attitude over time, and then by calculating the deviation of pitch and roll and its rates, the height control correction is reassigned based on the fuzzy algorithm. Finally, to verify the effectiveness and performance of the proposed combined control strategy, a validating test of ride height control system with and without road disturbance is carried out. Testing results show that the height adjusting time of both lifting and lowering is over 5 s, and the pitch angle and the roll angle of body attitude are less than 0.15°. This research proposes a hierarchical control method that can guarantee the attitude stability, as well as satisfy the ride height tracking system.

Does plyometric training improve vertical jump height? A meta-analytical review.

PubMed

Markovic, Goran

2007-06-01

The aim of this study was to determine the precise effect of plyometric training (PT) on vertical jump height in healthy individuals. Meta-analyses of randomised and non-randomised controlled trials that evaluated the effect of PT on four typical vertical jump height tests were carried out: squat jump (SJ); countermovement jump (CMJ); countermovement jump with the arm swing (CMJA); and drop jump (DJ). Studies were identified by computerised and manual searches of the literature. Data on changes in jump height for the plyometric and control groups were extracted and statistically pooled in a meta-analysis, separately for each type of jump. A total of 26 studies yielding 13 data points for SJ, 19 data points for CMJ, 14 data points for CMJA and 7 data points for DJ met the initial inclusion criteria. The pooled estimate of the effect of PT on vertical jump height was 4.7% (95% CI 1.8 to 7.6%), 8.7% (95% CI 7.0 to 10.4%), 7.5% (95% CI 4.2 to 10.8%) and 4.7% (95% CI 0.8 to 8.6%) for the SJ, CMJ, CMJA and DJ, respectively. When expressed in standardised units (ie, effect sizes), the effect of PT on vertical jump height was 0.44 (95% CI 0.15 to 0.72), 0.88 (95% CI 0.64 to 1.11), 0.74 (95% CI 0.47 to 1.02) and 0.62 (95% CI 0.18 to 1.05) for the SJ, CMJ, CMJA and DJ, respectively. PT provides a statistically significant and practically relevant improvement in vertical jump height with the mean effect ranging from 4.7% (SJ and DJ), over 7.5% (CMJA) to 8.7% (CMJ). These results justify the application of PT for the purpose of development of vertical jump performance in healthy individuals.

47 CFR 95.1315 - Antenna height restriction.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 5 2012-10-01 2012-10-01 false Antenna height restriction. 95.1315 Section 95... PERSONAL RADIO SERVICES Multi-Use Radio Service (MURS) General Provisions § 95.1315 Antenna height restriction. The highest point of any MURS antenna must no be more than 18.3 meters (60 feet) above the ground...

47 CFR 95.1315 - Antenna height restriction.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 5 2013-10-01 2013-10-01 false Antenna height restriction. 95.1315 Section 95... PERSONAL RADIO SERVICES Multi-Use Radio Service (MURS) General Provisions § 95.1315 Antenna height restriction. The highest point of any MURS antenna must no be more than 18.3 meters (60 feet) above the ground...

47 CFR 95.1315 - Antenna height restriction.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Antenna height restriction. 95.1315 Section 95... PERSONAL RADIO SERVICES Multi-Use Radio Service (MURS) General Provisions § 95.1315 Antenna height restriction. The highest point of any MURS antenna must no be more than 18.3 meters (60 feet) above the ground...

47 CFR 95.1315 - Antenna height restriction.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 5 2011-10-01 2011-10-01 false Antenna height restriction. 95.1315 Section 95... PERSONAL RADIO SERVICES Multi-Use Radio Service (MURS) General Provisions § 95.1315 Antenna height restriction. The highest point of any MURS antenna must no be more than 18.3 meters (60 feet) above the ground...

47 CFR 95.1315 - Antenna height restriction.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 5 2014-10-01 2014-10-01 false Antenna height restriction. 95.1315 Section 95... PERSONAL RADIO SERVICES Multi-Use Radio Service (MURS) General Provisions § 95.1315 Antenna height restriction. The highest point of any MURS antenna must no be more than 18.3 meters (60 feet) above the ground...

Using Television: How Undergraduate Female Students Utilize Television as a Cultural Resource

ERIC Educational Resources Information Center

King, Karen L.

2013-01-01

This qualitative dissertation study explores the ways television program content informs the participant's notions of academic and professional achievement and success. I argue that the undergraduate female students who participated in this study, whom I characterize as the post-feminist generation, are imagined as occupying a pivot point in…

My Very Own Imagination Library

ERIC Educational Resources Information Center

Conyers, Jeff

2012-01-01

Books in the home provide a pivotal connection point for caregivers and children for developing important social and emotional skills, as well the most critical life skills that children will acquire--literacy and a love of learning. However, access to books in many communities is limited and many households have no books at all. But what if…

The carbon balance pivot point of southwestern U.S. semiarid ecosystems: Insights from the 21st century drought

USDA-ARS?s Scientific Manuscript database

Global-scale studies indicate that semiarid regions strongly regulate the terrestrial carbon sink. However, we lack understanding of how climatic shifts, such as decadal drought, impact carbon sequestration across the wide-range of structural diversity in semiarid ecosystems. Therefore, we used edd...

Three-Dimensional Instruction: Using a New Type of Teaching in the Science Classroom

ERIC Educational Resources Information Center

Krajcik, Joe

2015-01-01

Science teaching and learning in the United States are at a pivotal point. "A Framework for K-12 Science Education" (NRC 2012b) and the "Next Generation Science Standards" ("NGSS"; NGSS Lead States 2013) shift science educators' focus from simply teaching science ideas to helping students figure out phenomena and…

Adorno: Cultural Education and Resistance

ERIC Educational Resources Information Center

Jessop, Sharon

2017-01-01

In recent years, culture has become significantly politicized, or conspicuously de-politicized, in different parts of the UK, making its appearance in education policy of pivotal interest and ripe for critical attention. From the vantage point of Theodor Adorno's work on the culture industry and his writings on the work of the teacher, I argue…

Drinking-Straw Microbalance and Seesaw: Stability and Instability

ERIC Educational Resources Information Center

Chapman, Peter; Glasser, Leslie

2015-01-01

The mechanics of a beam balance are little appreciated and seldom understood. We here consider the conditions that result in a stable balance, with center of gravity below the fulcrum (pivot point), while an unstable balance results when the center of gravity is above the fulcrum. The highly sensitive drinking-straw microbalance, which uses a…

49 CFR 571.213 - Standard No. 213; Child restraint systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the initial pre-test position of the respective knee pivot point, measured along a horizontal line... test dummy, specified in S7, when a child restraint system is tested in accordance with S6.1. Factory... body of a seated anthropomorphic test dummy, excluding the thighs, that lies between the top of the...

49 CFR 571.213 - Standard No. 213; Child restraint systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the initial pre-test position of the respective knee pivot point, measured along a horizontal line... test dummy, specified in S7, when a child restraint system is tested in accordance with S6.1. Factory... body of a seated anthropomorphic test dummy, excluding the thighs, that lies between the top of the...

49 CFR 571.213 - Standard No. 213; Child restraint systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the initial pre-test position of the respective knee pivot point, measured along a horizontal line... the head or torso of the appropriate test dummy, specified in S7, when a child restraint system is... (§ 571.225). Torso means the portion of the body of a seated anthropomorphic test dummy, excluding the...

Vietnamese Students' Transitions in Study Abroad Programs

ERIC Educational Resources Information Center

Nguyen, My Linh Thi

2012-01-01

Vietnam is at a pivotal point in positioning itself within the global economy. As organisations and government agendas are pushing for a more skilled workforce, it is evident that Vietnam has to deal with the implications for the changing educational landscape. This article presents a review of the literature related to study abroad, looking at…

A course in amplitudes

NASA Astrophysics Data System (ADS)

Taylor, Tomasz R.

2017-05-01

This a pedagogical introduction to scattering amplitudes in gauge theories. It proceeds from Dirac equation and Weyl fermions to the two pivot points of current developments: the recursion relations of Britto, Cachazo, Feng and Witten, and the unitarity cut method pioneered by Bern, Dixon, Dunbar and Kosower. In ten lectures, it covers the basic elements of on-shell methods.

Soviet SDI Rhetoric: The "Evil Empire" Vision of Mikhail Gorbachev.

ERIC Educational Resources Information Center

Kelley, Colleen E.

The symbolic presence of Ronald Reagan's Strategic Defense Initiative (SDI) has been and continues to be the pivot point in all summitry rhetoric between the American President and Soviet General Secretary Mikhail Gorbachev. To examine some of the rhetorical choices made by Gorbachev to dramatize his vision of why Ronald Reagan refuses to…

International Distance Learning in Special Education: A Program Evaluation of a US-Ecuador Collaboration

ERIC Educational Resources Information Center

McPherson, Rebekah

2010-01-01

The internationalization of distance learning in special education is at a pivotal point in expansion. Even with concerted efforts through traditional means to increase the supply of special educators, shortages persist; therefore, teacher preparation programs are turning to online education. This dissertation study was a formative program…

Still Indentured … and Their Parents Too

ERIC Educational Resources Information Center

Johannsen, Cryn

2016-01-01

In 2010, the author wrote an essay, "The New Indentured Educated Class," for "The New England Journal of Higher Education." This piece was pivotal in raising public awareness about a new group of Americans, an enormous group of people--educated and deeply in debt. At that point, few were talking about the student loan debt…

Learning Styles: A Pivotal Point for Retention and Career Decision Guidance.

ERIC Educational Resources Information Center

Jenkins, Jeannette

The importance of learning styles to student retention and career decision guidance is considered. Learning style is the way people process information and solve problems. Research on right and left brain processing, which indicates that the left hemisphere controls thoughts that are predominately rational and the right hemisphere controls…

Exact Identification of a Quantum Change Point

NASA Astrophysics Data System (ADS)

Sentís, Gael; Calsamiglia, John; Muñoz-Tapia, Ramon

2017-10-01

The detection of change points is a pivotal task in statistical analysis. In the quantum realm, it is a new primitive where one aims at identifying the point where a source that supposedly prepares a sequence of particles in identical quantum states starts preparing a mutated one. We obtain the optimal procedure to identify the change point with certainty—naturally at the price of having a certain probability of getting an inconclusive answer. We obtain the analytical form of the optimal probability of successful identification for any length of the particle sequence. We show that the conditional success probabilities of identifying each possible change point show an unexpected oscillatory behavior. We also discuss local (online) protocols and compare them with the optimal procedure.

Exact Identification of a Quantum Change Point.

PubMed

Sentís, Gael; Calsamiglia, John; Muñoz-Tapia, Ramon

2017-10-06

The detection of change points is a pivotal task in statistical analysis. In the quantum realm, it is a new primitive where one aims at identifying the point where a source that supposedly prepares a sequence of particles in identical quantum states starts preparing a mutated one. We obtain the optimal procedure to identify the change point with certainty-naturally at the price of having a certain probability of getting an inconclusive answer. We obtain the analytical form of the optimal probability of successful identification for any length of the particle sequence. We show that the conditional success probabilities of identifying each possible change point show an unexpected oscillatory behavior. We also discuss local (online) protocols and compare them with the optimal procedure.

How Big Is It Really? Assessing the Efficacy of Indirect Estimates of Body Size in Asian Elephants.

PubMed

Chapman, Simon N; Mumby, Hannah S; Crawley, Jennie A H; Mar, Khyne U; Htut, Win; Thura Soe, Aung; Aung, Htoo Htoo; Lummaa, Virpi

2016-01-01

Information on an organism's body size is pivotal in understanding its life history and fitness, as well as helping inform conservation measures. However, for many species, particularly large-bodied wild animals, taking accurate body size measurements can be a challenge. Various means to estimate body size have been employed, from more direct methods such as using photogrammetry to obtain height or length measurements, to indirect prediction of weight using other body morphometrics or even the size of dung boli. It is often unclear how accurate these measures are because they cannot be compared to objective measures. Here, we investigate how well existing estimation equations predict the actual body weight of Asian elephants Elephas maximus, using body measurements (height, chest girth, length, foot circumference and neck circumference) taken directly from a large population of semi-captive animals in Myanmar (n = 404). We then define new and better fitting formulas to predict body weight in Myanmar elephants from these readily available measures. We also investigate whether the important parameters height and chest girth can be estimated from photographs (n = 151). Our results show considerable variation in the ability of existing estimation equations to predict weight, and that the equations proposed in this paper predict weight better in almost all circumstances. We also find that measurements from standardised photographs reflect body height and chest girth after applying minor adjustments. Our results have implications for size estimation of large wild animals in the field, as well as for management in captive settings.

How Big Is It Really? Assessing the Efficacy of Indirect Estimates of Body Size in Asian Elephants

PubMed Central

Chapman, Simon N.; Mumby, Hannah S.; Crawley, Jennie A. H.; Mar, Khyne U.; Htut, Win; Thura Soe, Aung; Aung, Htoo Htoo; Lummaa, Virpi

2016-01-01

Information on an organism’s body size is pivotal in understanding its life history and fitness, as well as helping inform conservation measures. However, for many species, particularly large-bodied wild animals, taking accurate body size measurements can be a challenge. Various means to estimate body size have been employed, from more direct methods such as using photogrammetry to obtain height or length measurements, to indirect prediction of weight using other body morphometrics or even the size of dung boli. It is often unclear how accurate these measures are because they cannot be compared to objective measures. Here, we investigate how well existing estimation equations predict the actual body weight of Asian elephants Elephas maximus, using body measurements (height, chest girth, length, foot circumference and neck circumference) taken directly from a large population of semi-captive animals in Myanmar (n = 404). We then define new and better fitting formulas to predict body weight in Myanmar elephants from these readily available measures. We also investigate whether the important parameters height and chest girth can be estimated from photographs (n = 151). Our results show considerable variation in the ability of existing estimation equations to predict weight, and that the equations proposed in this paper predict weight better in almost all circumstances. We also find that measurements from standardised photographs reflect body height and chest girth after applying minor adjustments. Our results have implications for size estimation of large wild animals in the field, as well as for management in captive settings. PMID:26938085

The Carbon Balance Pivot Point of Southwestern U.S. Semiarid Ecosystems: Insights From the 21st Century Drought

NASA Astrophysics Data System (ADS)

Scott, R. L.; Biederman, J.; Barron-Gafford, G.; Hamerlynck, E. P.

2015-12-01

Global-scale studies indicate that semiarid ecosystems strongly regulate the long-term trend and interannual variability of the terrestrial carbon sink, possibly due to changes in vegetation and an inherent sensitivity to changes in water availability. However, we lack understanding of how climate shifts, such as the ongoing decadal-scale drought in the Southwest US, impact carbon sink functioning in semiarid ecosystems with differing structure. Therefore, we investigated the response of net ecosystem production of carbon dioxide (NEP) to changes in annual water availability in four Southwest US ecosystems varying in relative shrub, tree and grass abundance. Using eddy covariance carbon dioxide and water vapor flux measurements collected over the last drought-impacted decade, we identified a precipitation "pivot point" in the annual carbon balance for each ecosystem type where annual NEP switched from negative to positive. At the three sites with larger amounts of grass, rather than woody plant, cover, pivot points were closer to the drought-period mean annual precipitation (MAP) than MAP over the preceding 30 years, suggesting the carbon pools of these grassier ecosystems have more quickly adjusted to the decadal-scale drought. Current-year water availability, as quantified by evapotranspiration (ET) overwhelmingly drove the response of gross ecosystem photosynthesis (GEP) and respiration (Reco) fluxes. Ecosystem water use efficiency (GEP/ET) increased with water availability and leaf area index, resulting in a more efficient photosynthetic use of water in wetter years and at wetter sites. Grasslands supported a higher leaf area than shrublands at a given water availability, and thus had higher GEP/ET. Differences in GEP/ET were also related to the relative proportion of abiotic evaporation, estimated from the ET intercept in a linear regression of ET and GEP, to total ET at a site, highlighting the importance of ET partitioning for understanding how semiarid rainfall drives plant productivity.

Development of an automated method to detect sitting pivot transfer phases using biomechanical variables: toward a standardized method

PubMed Central

2012-01-01

Background Sitting pivot transfer (SPT) is one of the most important, but at the same time strenuous at the upper extremity, functional task for spinal cord injured individuals. In order to better teach this task to those individuals and to improve performance, a better biomechanical understanding during the different SPT phases is a prerequisite. However, no consensus has yet been reached on how to depict the different phases of the SPT. The definition of the phases of the SPT, along with the events characterizing these phases, will facilitate the interpretation of biomechanical outcome measures related to the performance of SPTs as well as strengthen the evidence generated across studies. Methods Thirty-five individuals with a spinal cord injury performed two SPTs between seats of similar height using their usual SPT technique. Kinematics and kinetics were recorded using an instrumented transfer assessment system. Based on kinetic and kinematic measurements, a relative threshold-based algorithm was developed to identify four distinct phases: pre-lift, upper arm loading, lift-pivot and post-lift phases. To determine the stability of the algorithm between the two SPTs, Student t-tests for dependent samples were performed on the absolute duration of each phase. Results The mean total duration of the SPT was 2.00 ± 0.49 s. The mean duration of the pre-lift, upper arm loading, lift-pivot and post-lift phases were 0.74 ± 0.29 s, 0.28 ± 0.13 s, 0.72 ± 0.24 s, 0.27 ± 0.14 s whereas their relative contributions represented approximately 35%, 15%, 35% and 15% of the overall SPT cycle, respectively. No significant differences were found between the trials (p = 0.480-0.891). Conclusion The relative threshold-based algorithm used to automatically detect the four distinct phases of the SPT, is rapid, accurate and repeatable. A quantitative and thorough description of the precise phases of the SPT is prerequisite to better interpret biomechanical findings and measure task performance. The algorithm could also become clinically useful to refine the assessment and training of SPTs. PMID:22305052

Fabrication of long-focal-length plano-convex microlens array by combining the micro-milling and injection molding processes.

PubMed

Chen, Lei; Kirchberg, Stefan; Jiang, Bing-Yan; Xie, Lei; Jia, Yun-Long; Sun, Lei-Lei

2014-11-01

A uniform plano-convex spherical microlens array with a long focal length was fabricated by combining the micromilling and injection molding processes in this work. This paper presents a quantitative study of the injection molding process parameters on the uniformity of the height of the microlenses. The variation of the injection process parameters, i.e., barrel temperature, mold temperature, injection speed, and packing pressure, was found to have a significant effect on the uniformity of the height of the microlenses, especially the barrel temperature. The filling-to-packing switchover point is also critical to the uniformity of the height of the microlenses. The optimal uniformity was achieved when the polymer melts completely filled the mold cavity, or even a little excessively filled the cavity, during the filling stage. In addition, due to the filling resistance, the practical filling-to-packing switchover point can vary with the change of the filling processing conditions and lead to a non-negligible effect on the uniformity of the height of the microlenses. Furthermore, the effect of injection speed on the uniformity of the height of the microlenses was analyzed in detail. The results indicated that the effect of injection speed on the uniformity of the height of the microlenses is mainly attributed to the two functions of injection speed: transferring the filling-to-packing switchover point and affecting the distribution of residual flow stress in the polymer melt.

Laser device

DOEpatents

Scott, Jill R.; Tremblay, Paul L.

2008-08-19

A laser device includes a virtual source configured to aim laser energy that originates from a true source. The virtual source has a vertical rotational axis during vertical motion of the virtual source and the vertical axis passes through an exit point from which the laser energy emanates independent of virtual source position. The emanating laser energy is collinear with an orientation line. The laser device includes a virtual source manipulation mechanism that positions the virtual source. The manipulation mechanism has a center of lateral pivot approximately coincident with a lateral index and a center of vertical pivot approximately coincident with a vertical index. The vertical index and lateral index intersect at an index origin. The virtual source and manipulation mechanism auto align the orientation line through the index origin during virtual source motion.

Acoustic imaging system

DOEpatents

Smith, Richard W.

1979-01-01

An acoustic imaging system for displaying an object viewed by a moving array of transducers as the array is pivoted about a fixed point within a given plane. A plurality of transducers are fixedly positioned and equally spaced within a laterally extending array and operatively directed to transmit and receive acoustic signals along substantially parallel transmission paths. The transducers are sequentially activated along the array to transmit and receive acoustic signals according to a preestablished sequence. Means are provided for generating output voltages for each reception of an acoustic signal, corresponding to the coordinate position of the object viewed as the array is pivoted. Receptions from each of the transducers are presented on the same display at coordinates corresponding to the actual position of the object viewed to form a plane view of the object scanned.

Morphologic Characteristics Help Explain the Gender Difference in Peak Anterior Cruciate Ligament Strain During a Simulated Pivot Landing

PubMed Central

Lipps, David B.; Oh, Youkeun K.; Ashton-Miller, James A.; Wojtys, Edward M.

2015-01-01

Background Gender differences exist in anterior cruciate ligament (ACL) cross-sectional area and lateral tibial slope. Biomechanical principles suggest that the direction of these gender differences should induce larger peak ACL strains in females under dynamic loading. Hypothesis Peak ACL relative strain during a simulated pivot landing is significantly greater in female ACLs than male ACLs. Study Design Controlled laboratory study. Methods Twenty cadaveric knees from height- and weight-matched male and female cadavers were subjected to impulsive 3-dimensional test loads of 2 times body weight in compression, flexion, and internal tibial torque starting at 15° of flexion. Load cells measured the 3-dimensional forces and moments applied to the knee, and forces in the pretensioned quadriceps, hamstring, and gastrocnemius muscle equivalents. A novel, gender-specific, nonlinear spring simulated short-range and longer range quadriceps muscle tensile stiffness. Peak relative strain in the anteromedial bundle of the ACL (AM-ACL) was measured using a differential variable reluctance transducer, while ACL cross-sectional area and lateral tibial slope were measured using magnetic resonance imaging. A repeated-measures Mann-Whitney signed-rank test was used to test the hypothesis. Results Female knees exhibited 95% greater peak AM-ACL relative strain than male knees (6.37% [22.53%] vs 3.26% [11.89%]; P = .004). Anterior cruciate ligament cross-sectional area and lateral tibial slope were significant predictors of peak AM-ACL relative strain (R2 = .59; P = .001). Conclusion Peak AM-ACL relative strain was significantly greater in female than male knees from donors of the same height and weight. This gender difference is attributed to a smaller female ACL cross-sectional area and a greater lateral tibial slope. Clinical Relevance Since female ACLs are systematically exposed to greater strain than their male counterparts, training and injury prevention programs should take this fact into consideration. PMID:21917612

Remote controlled vacuum joint closure mechanism

DOEpatents

Doll, David W.; Hager, E. Randolph

1986-01-01

A remotely operable and maintainable vacuum joint closure mechanism for a noncircular aperture is disclosed. The closure mechanism includes an extendible bellows coupled at one end to a noncircular duct and at its other end to a flange assembly having sealed grooves for establishing a high vacuum seal with the abutting surface of a facing flange which includes an aperture forming part of the system to be evacuated. A plurality of generally linear arrangements of pivotally coupled linkages and piston combinations are mounted around the outer surface of the duct and aligned along the length thereof. Each of the piston/linkage assemblies is adapted to engage the flange assembly by means of a respective piston and is further coupled to a remote controlled piston drive shaft to permit each of the linkages positioned on a respective flat outer surface of the duct to simultaneously and uniformly displace a corresponding piston and the flange assembly with which it is in contact along the length of the duct in extending the bellows to provide a high vacuum seal between the movable flange and the facing flange. A plurality of latch mechanisms are also pivotally mounted on the outside of the duct. A first end of each of the latch mechanisms is coupled to a remotely controlled latch control shaft for displacing the latch mechanism about its pivot point. In response to the pivoting displacement of the latch mechanism, a second end thereof is displaced so as to securely engage the facing flange.

"Palmar pivot flap" for resurfacing palmar lateral defects of the fingers.

PubMed

Yam, Andrew; Peng, Yeong-Pin; Pho, Robert Wan-Heng

2008-12-01

Soft tissue defects on the lateral borders of the digits are difficult to reconstruct using local or local-regional flaps. We describe a "palmar pivot flap" to resurface an adjacent defect on the palmar-lateral aspect of the digit. The surgical technique is described. This flap is an axial pattern flap based on the subcutaneous transverse branches of the digital artery. The flap is pivoted up to 90 degrees on the neurovascular bundle in its base, into an adjacent defect. The flap can be raised from either the proximal or the middle phalangeal segments. It can cover defects sited from the level of the proximal interphalangeal joint up to the fingertip. The donor defect is limited to the same digit and is covered with a full-thickness skin graft. We have used this flap on 3 patients with defects at the middle phalangeal segment, the distal interphalangeal joint, and the fingertip. All healed primarily. One patient had a mild flexion contracture of the proximal interphalangeal joint, whereas the other 2 had no complications. The patients with distal interphalangeal joint and fingertip defects had excellent sensation in the flap (2-point discrimination of 5-6 mm). The palmar pivot flap is useful for resurfacing otherwise difficult defects on the lateral borders of the digits around and distal to the proximal interphalangeal joint, including those at the fingertip. It provides sensate, glabrous skin. The donor defect is on the same digit and is well hidden, producing an aesthetic and functional reconstruction.

Valve stem and packing assembly

DOEpatents

Wordin, J.J.

1991-09-03

A valve stem and packing assembly is provided in which a rotatable valve stem includes a first tractrix surface for sliding contact with a stem packing and also includes a second tractrix surface for sliding contact with a bonnet. Force is applied by means of a spring, gland flange, and gland on the stem packing so the stem packing seals to the valve stem and bonnet. This configuration serves to create and maintain a reliable seal between the stem packing and the valve stem. The bonnet includes a second complementary tractrix surface for contacting the second sliding tractrix surface, the combination serving as a journal bearing for the entire valve stem and packing assembly. The journal bearing so configured is known as a Schiele's pivot. The Schiele's pivot also serves to maintain proper alignment of the valve stem with respect to the bonnet. Vertical wear between the surfaces of the Schiele's pivot is uniform at all points of contact between the second sliding tractrix surface and the second complementary tractrix surface of a bonnet. The valve stem is connected to a valve plug by means of a slip joint. The valve is opened and closed by rotating the valve stem. The slip joint compensates for wear on the Schiele's pivot and on the valve plug. A ledge is provided on the valve bonnet for the retaining nut to bear against. The ledge prevents over tightening of the retaining nut and the resulting excessive friction between stem and stem packing. 2 figures.

Valve stem and packing assembly

DOEpatents

Wordin, John J.

1991-01-01

A valve stem and packing assembly is provided in which a rotatable valve stem includes a first tractrix surface for sliding contact with a stem packing and also includes a second tractrix surface for sliding contact with a bonnet. Force is applied by means of a spring, gland flange, and gland on the stem packing so the stem packing seals to the valve stem and bonnet. This configuration serves to create and maintain a reliable seal between the stem packing and the valve stem. The bonnet includes a second complementary tractrix surface for contacting the second sliding tractrix surface, the combination serving as a journal bearing for the entire valve stem and packing assembly. The journal bearing so configured is known as a Schiele's pivot. The Schiele's pivot also serves to maintain proper alignment of the valve stem with respect to the bonnet. Vertical wear between the surfaces of the Schiele's pivot is uniform at all points of contact between the second sliding tractrix surface and the second complementary tractrix surface of a bonnet. The valve stem is connected to a valve plug by means of a slip joint. The valve is opened and closed by rotating the valve stem. The slip joint compensates for wear on the Schiele's pivot and on the valve plug. A ledge is provided on the valve bonnet for the retaining nut to bear against. The ledge prevents overtightening of the retaining nut and the resulting excessive friction between stem and stem packing.

The Role of Positive Psychology in Enhancing Satisfaction, Motivation, and Productivity in the Workplace

ERIC Educational Resources Information Center

Martin, Andrew J.

2005-01-01

Positive psychology offers scope for enhancing satisfaction, motivation, and productivity in the workplace. Wiegand and Geller (2004, this issue) point to a number of strategies to enhance individuals' success orientation and conclude their discussion with the actively caring model which appears to be a useful means of representing pivotal facets…

Weird Science: Further Thoughts on the STEM Educational Challenge

ERIC Educational Resources Information Center

Halfond, Jay A.

2010-01-01

The author notes that the sciences are now something one must latch onto early and successfully as a teenager, and endure against all odds. This pivotal point requires maturity and even myopia--delayed gratification and voluntary dorkiness--traits not common in the young. As a nation, Americans are losing their hegemony in the sciences. In just…

Strategy Precedes Operational Effectiveness: Aligning High Graduation Rankings with Competitive Graduation Grade Point Averages

ERIC Educational Resources Information Center

Apprey, Maurice; Bassett, Kimberley C.; Preston-Grimes, Patrice; Lewis, Dion W.; Wood, Beverly

2014-01-01

Two pivotal and interconnected claims are addressed in this article. First, strategy precedes program effectiveness. Second, graduation rates and rankings are insufficient in any account of academic progress for African American students. In this article, graduation is regarded as the floor and not the ceiling, as it were. The ideal situation in…

Casting a Statewide Strategic Performance Net: Interlaced Data and Responsive Supports

ERIC Educational Resources Information Center

Layland, Allison; Redding, Sam

2017-01-01

The pivot point for educational change is now firmly placed with the district, rebalancing the position of the state and the school relative to the local education agency (LEA). The state education agency (SEA) has been shifting its emphasis for decades, from a compliance-focused authority to a change agent equipped with systems, processes,…

Pivot Points: Direct Measures of the Content and Process of Community-Based Learning

ERIC Educational Resources Information Center

Wickersham, Carol; Westerberg, Charles; Jones, Karen; Cress, Margaret

2016-01-01

This research is an initial investigation into the ways community-based learning increase the cognitive skills central to the exercise of the sociological imagination. In addition to identifying a means to reveal that learning had occurred, we looked for evidence that the students were mastering sociological content, especially the concepts and…

Academic Socialization and the Transition to Elementary School: Parents' Conceptions of School Readiness, Practices, and Children's Academic Achievement Trajectories

ERIC Educational Resources Information Center

Puccioni, Jaime Lynn

2012-01-01

By the time children enter kindergarten, significant socioeconomic and racial gaps in academic achievement exist (Coley, 2002; Rouse, Brooks-Gunn, & Mclanahan, 2005). Kindergarten is considered to be a pivotal point of educational transition, as academic achievement upon kindergarten entry is associated with subsequent academic success…

Using GPS and leveling data in local precise geoid determination and case study

NASA Astrophysics Data System (ADS)

Erol, B.; Çelik, R. N.; Erol, S.

2003-04-01

As an important result of developments in high technology, satellite based positioning system has become to use in geodesy and surveying professions. These developments made the measurement works more accurate, more practical and more economic. Today, one of the most recent used satellite based positioning system is GPS (Global Positioning System) and it serves to a very wide range of geodetic applications from monitoring earth crustal deformations till building the basis for a GIS (Geographical Information Systems). The most efficient way to utilize GPS measurement system for mentioned aims is having a reliable geodetic infrastructure in working area. Geodetic infrastructure is a extraterrestrial and time system and involved 4D geodetic reference networks. The forth element of mentioned geodetic reference system is time because having an accurate and reliable geodetic infrastructure is needed to up-date according to physical realities of the region. By the help of a well designed geodetic infrastructure accurate and reliable coordinates of a point can be generated economically every time in a global and up-to-date system. Geoid is one of the important parts of a geodetic infrastructure. As it is well known, geoid is the equipotential surface of the Earth's gravity field which best fits, in a least squares sense, global mean sea level and it is reference for physical height systems like orthometric and normal heights. In the most of the applications, vertical position of a point is expressed with orthometric or normal height. Orthometric or normal height is a physical concept and gives vertical position of a point uniquely. On the other hand, vertical position of a point is derived in a geometrical system according to GPS measurements. GPS datum is WGS84 and in this system, an ellipsoidal height of a point is calculated according to WGS84 ellipsoid. So, it is an necessity to transform the ellipsoidal heights to orthometric heights and this procedure is managed with the fundamental mathematical equation; N=h-H. In the equation, "h" is the ellipsoidal height of a point P, "H" is the orthometric height of the same point and "N" is "geoid undulation" value. Normally, "H" orthometric height derived from leveling measurements but these measurements are tiring applications. So, while having a geoid model in the region as the essential part of geodetic infrastructure, number leveling measurements can be reduced from the procedure and by this way time and labor is saved. Geoid determination is modeling of the data in such a way that geoid height can be obtained digital or analog at a point whose horizontal position is known. Geoid models can be developed for local, regional or global regions. Using satellite techniques, especially GPS, in geodetic measurements are increased importance of geoid. Because geoid is a natural tie between high precision geodetic coordinates and coordinates which obtained from satellites. There are several geoid determination methods according to used data and models. GPS/Leveling method, which is also known as geometric method, is one of these methods. This method is appropriate for local precise geoid determination in respectively small areas. In this paper, it is going to be given information about GPS/Leveling geoid determination method and mathematical models, which are used in geoid determination with this method. And Izmir local geoid model will be presented as a case study. Izmir is one of the west metropolitan cities of Turkey and located near Aegean Sea. The topography is extremely rough in the region. There are two different geoid determination studies which were carried out in 1996 and 2001 in Izmir. Both models were accomplished according to GPS/Leveling method. Those two geoid models of Izmir Metropolitan region are investigated in here, the conflict of them were discussed. The relation between distribution of common reference points and differences of geoid undulation values, which are calculated from both models separately, were analyzed and also effects of topography on conflict of both geoid model was investigated. The results of the study and suggestions are going to be given in the paper.

Deriving Temporal Height Information for Maize Breeding

NASA Astrophysics Data System (ADS)

Malambo, L.; Popescu, S. C.; Murray, S.; Sheridan, R.; Richardson, G.; Putman, E.

2016-12-01

Phenotypic data such as height provide useful information to crop breeders to better understand their field experiments and associated field variability. However, the measurement of crop height in many breeding programs is done manually which demands significant effort and time and does not scale well when large field experiments are involved. Through structure from motion (SfM) techniques, small unmanned aerial vehicles (sUAV) or drones offer tremendous potential for generating crop height data and other morphological data such as canopy area and biomass in cost-effective and efficient way. We present results of an on-going UAV application project aimed at generating temporal height metrics for maize breeding at the Texas A&M AgriLife Research farm in Burleson County, Texas. We outline the activities involved from the drone aerial surveys, image processing and generation of crop height metrics. The experimental period ran from April (planting) through August (harvest) 2016 and involved 36 maize hybrids replicated over 288 plots ( 1.7 Ha). During the time, crop heights were manually measured per plot at weekly intervals. Corresponding aerial flights were carried out using a DJI Phantom 3 Professional UAV at each interval and images captured processed into point clouds and image mosaics using Pix4D (Pix4D SA; Lausanne, Switzerland) software. LiDAR data was also captured at two intervals (05/06 and 07/29) to provide another source of height information. To obtain height data per plot from SfM point clouds and LiDAR data, percentile height metrics were then generated using FUSION software. Results of the comparison between SfM and field measurement height show high correlation (R2 > 0.7), showing that use of sUAV can replace laborious manual height measurement and enhance plant breeding programs. Similar results were also obtained from the comparison of SfM and LiDAR heights. Outputs of this project are helping plant breeders at Texas A&M automate routine height measurements in maize and quickly make actionable decisions and discover new hybrids.

STEREOSCOPIC DETERMINATION OF HEIGHTS OF EXTREME ULTRAVIOLET BRIGHT POINTS USING DATA TAKEN BY SECCHI/EUVI ABOARD STEREO

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kwon, Ryun-Young; Chae, Jongchul; Zhang Jie

2010-05-01

We measure the heights of EUV bright points (BPs) above the solar surface by applying a stereoscopic method to the data taken by the Solar TErrestrial RElations Observatory/SECCHI/Extreme UltraViolet Imager (EUVI). We have developed a three-dimensional reconstruction method for point-like features such as BPs using the simple principle that the position of a point in the three-dimensional space is specified as the intersection of two lines of sight. From a set of data consisting of EUVI 171 A, 195 A, 284 A, and 304 A images taken on 11 days arbitrarily selected during a period of 14 months, we havemore » identified and analyzed 210 individual BPs that were visible on all four passband images and smaller than 30 Mm. The BPs seen in the 304 A images have an average height of 4.4 Mm, and are often associated with the legs of coronal loops. In the 171 A, 195 A, and 284 A images the BPs appear loop-shaped, and have average heights of 5.1, 6.7, and 6.1 Mm, respectively. Moreover, there is a tendency that overlying loops are filled with hotter plasmas. The average heights of BPs in 171 A, 195 A, and 284 A passbands are roughly twice the corresponding average lengths. Our results support the notion that an EUV BP represents a system of small loops with temperature stratification like flaring loops, being consistent with the magnetic reconnection origin.« less

An Online 3D Database System for Endangered Architectural and Archaeological Heritage in the South-Eastern Mediterranean

NASA Astrophysics Data System (ADS)

Abate, D.; Avgousti, A.; Faka, M.; Hermon, S.; Bakirtzis, N.; Christofi, P.

2017-10-01

This study compares performance of aerial image based point clouds (IPCs) and light detection and ranging (LiDAR) based point clouds in detection of thinnings and clear cuts in forests. IPCs are an appealing method to update forest resource data, because of their accuracy in forest height estimation and cost-efficiency of aerial image acquisition. We predicted forest changes over a period of three years by creating difference layers that displayed the difference in height or volume between the initial and subsequent time points. Both IPCs and LiDAR data were used in this process. The IPCs were constructed with the Semi-Global Matching (SGM) algorithm. Difference layers were constructed by calculating differences in fitted height or volume models or in canopy height models (CHMs) from both time points. The LiDAR-derived digital terrain model (DTM) was used to scale heights to above ground level. The study area was classified in logistic regression into the categories ClearCut, Thinning or NoChange with the values from the difference layers. We compared the predicted changes with the true changes verified in the field, and obtained at best a classification accuracy for clear cuts 93.1 % with IPCs and 91.7 % with LiDAR data. However, a classification accuracy for thinnings was only 8.0 % with IPCs. With LiDAR data 41.4 % of thinnings were detected. In conclusion, the LiDAR data proved to be more accurate method to predict the minor changes in forests than IPCs, but both methods are useful in detection of major changes.

Impact of Footprint Diameter and Off-Nadir Pointing on the Precision of Canopy Height Estimates from Spaceborne Lidar

NASA Technical Reports Server (NTRS)

Pang, Yong; Lefskky, Michael; Sun, Guoqing; Ranson, Jon

2011-01-01

A spaceborne lidar mission could serve multiple scientific purposes including remote sensing of ecosystem structure, carbon storage, terrestrial topography and ice sheet monitoring. The measurement requirements of these different goals will require compromises in sensor design. Footprint diameters that would be larger than optimal for vegetation studies have been proposed. Some spaceborne lidar mission designs include the possibility that a lidar sensor would share a platform with another sensor, which might require off-nadir pointing at angles of up to 16 . To resolve multiple mission goals and sensor requirements, detailed knowledge of the sensitivity of sensor performance to these aspects of mission design is required. This research used a radiative transfer model to investigate the sensitivity of forest height estimates to footprint diameter, off-nadir pointing and their interaction over a range of forest canopy properties. An individual-based forest model was used to simulate stands of mixed conifer forest in the Tahoe National Forest (Northern California, USA) and stands of deciduous forests in the Bartlett Experimental Forest (New Hampshire, USA). Waveforms were simulated for stands generated by a forest succession model using footprint diameters of 20 m to 70 m. Off-nadir angles of 0 to 16 were considered for a 25 m diameter footprint diameter. Footprint diameters in the range of 25 m to 30 m were optimal for estimates of maximum forest height (R(sup 2) of 0.95 and RMSE of 3 m). As expected, the contribution of vegetation height to the vertical extent of the waveform decreased with larger footprints, while the contribution of terrain slope increased. Precision of estimates decreased with an increasing off-nadir pointing angle, but off-nadir pointing had less impact on height estimates in deciduous forests than in coniferous forests. When pointing off-nadir, the decrease in precision was dependent on local incidence angle (the angle between the off-nadir beam and a line normal to the terrain surface) which is dependent on the off-nadir pointing angle, terrain slope, and the difference between the laser pointing azimuth and terrain aspect; the effect was larger when the sensor was aligned with the terrain azimuth but when aspect and azimuth are opposed, there was virtually no effect on R2 or RMSE. A second effect of off-nadir pointing is that the laser beam will intersect individual crowns and the canopy as a whole from a different angle which had a distinct effect on the precision of lidar estimates of height, decreasing R2 and increasing RMSE, although the effect was most pronounced for coniferous crowns.

Dual frequency scatterometer measurement of ocean wave height

NASA Technical Reports Server (NTRS)

Johnson, J. W.; Jones, W. L.; Swift, C. T.; Grantham, W. L.; Weissman, D. E.

1975-01-01

A technique for remotely measuring wave height averaged over an area of the sea surface was developed and verified with a series of aircraft flight experiments. The measurement concept involves the cross correlation of the amplitude fluctuations of two monochromatic reflected signals with variable frequency separation. The signal reflected by the randomly distributed specular points on the surface is observed in the backscatter direction at nadir incidence angle. The measured correlation coefficient is equal to the square of the magnitude of the characteristic function of the specular point height from which RMS wave height can be determined. The flight scatterometer operates at 13.9 GHz and 13.9 - delta f GHz with a maximum delta f of 40 MHz. Measurements were conducted for low and moderate sea states at altitudes of 2, 5, and 10 thousand feet. The experimental results agree with the predicted decorrelation with frequency separation and with off-nadir incidence angle.

Estimating Forest Canopy Heights and Aboveground Biomass with Simulated ICESat-2 Data

NASA Astrophysics Data System (ADS)

Malambo, L.; Narine, L.; Popescu, S. C.; Neuenschwander, A. L.; Sheridan, R.

2016-12-01

The Ice, Cloud and Land Elevation Satellite (ICESat) 2 is scheduled for launch in 2017 and one of its overall science objectives will be to measure vegetation heights, which can be used to estimate and monitor aboveground biomass (AGB) over large spatial scales. This study serves to develop a methodology for utilizing vegetation data collected by ICESat-2 that will be on a five-year mission from 2017, for mapping forest canopy heights and estimating aboveground forest biomass (AGB). The specific objectives are to, (1) simulate ICESat-2 photon-counting lidar (PCL) data, (2) utilize simulated PCL data to estimate forest canopy heights and propose a methodology for upscaling PCL height measurements to obtain spatially contiguous coverage and, (3) estimate and map AGB using simulated PCL data. The laser pulse from ICESat-2 will be divided into three pairs of beams spaced approximately 3 km apart, with footprints measuring approximately 14 m in diameter and with 70 cm along-track intervals. Using existing airborne lidar data (ALS) for Sam Houston National Forest (SHNF) and known ICESat-2 beam locations, footprints are generated along beam locations and PCL data are then simulated from discrete return lidar points within each footprint. By applying data processing algorithms, photons are classified into top of canopy points and ground surface elevation points to yield tree canopy height values within each ICESat-2 footprint. AGB is then estimated using simple linear regression that utilizes AGB from a biomass map generated with ALS data for SHNF and simulated PCL height metrics for 100 m segments along ICESat-2 tracks. Two approaches also investigated for upscaling AGB estimates to provide wall-to-wall coverage of AGB are (1) co-kriging and (2) Random Forest. Height and AGB maps, which are the outcomes of this study, will demonstrate how data acquired by ICESat-2 can be used to measure forest parameters and in extension, estimate forest carbon for climate change initiatives.

[Finite element analysis of mechanical characteristics during retracting mandibular incisors through sliding mechanics].

PubMed

Gu, Yong-Jia; Wu, Yan-Ping; Gao, Mei-Qin; Yao, Ning; Chen, Wen-Jing

2008-10-01

To analyze the mechanical characteristic changes of teeth and arch under different loading direction during retracting mandibular incisors through implant, simulating clinical loading system. Three- dimensional finite element model, including brackets, archwire, crampable hooks and implants, was reconstructed. The force direction was determined by connecting the points in crampable hook and the center point of implant, and the force point and force direction were changed with the adjustment of the height of crampable hook and the height of implant. Then three-dimensional movement trend of teeth, stress distribution in periodontal membrane and the largest displacement of archwire nodes in each group were calculated and analyzed. SPSS13.0 software package was used for statistical analysis. It was found that the height of implant and the height of crampable hook were correlated with the movement of teeth and stress distribution in periodontal membrane (P<0.01). The movement trend of teeth in the condition of different height of implant and different height of crampable hook was illustrated as follows:(1)with the height increase of crampable hook, the movement trend of the central and lateral incisors varied from mesial lingual tipping to mesial labial tipping. However, canines tipped distally and lingually; the second premolars tipped mesially and lingually, and the first molar roots tipped distally and buccally with decreasing tipping angle. (2) The largest stress distribution in the whole arch was located in the labial apical one-third area of the lateral incisors, while that of canines and the first molars was located in the alveolar ridges and root bifurcations. These findings indicate that the different movement trend during retracting anterior teeth can be achieved through the adjustment of the height of crampable hook, and implant, anchorage can effectively control anterior movement of the posterior teeth. Supported by Research Fund of Bureau of Science and Technology of Nantong City (Grant No. S40023).

Influence of micro-topography and crown characteristics on tree height estimations in tropical forests based on LiDAR canopy height models

NASA Astrophysics Data System (ADS)

Alexander, Cici; Korstjens, Amanda H.; Hill, Ross A.

2018-03-01

Tree or canopy height is an important attribute for carbon stock estimation, forest management and habitat quality assessment. Airborne Laser Scanning (ALS) based on Light Detection and Ranging (LiDAR) has advantages over other remote sensing techniques for describing the structure of forests. However, sloped terrain can be challenging for accurate estimation of tree locations and heights based on a Canopy Height Model (CHM) generated from ALS data; a CHM is a height-normalised Digital Surface Model (DSM) obtained by subtracting a Digital Terrain Model (DTM) from a DSM. On sloped terrain, points at the same elevation on a tree crown appear to increase in height in the downhill direction, based on the ground elevations at these points. A point will be incorrectly identified as the treetop by individual tree crown (ITC) recognition algorithms if its height is greater than that of the actual treetop in the CHM, which will be recorded as the tree height. In this study, the influence of terrain slope and crown characteristics on the detection of treetops and estimation of tree heights is assessed using ALS data in a tropical forest with complex terrain (i.e. micro-topography) and tree crown characteristics. Locations and heights of 11,442 trees based on a DSM are compared with those based on a CHM. The horizontal (DH) and vertical displacements (DV) increase with terrain slope (r = 0.47 and r = 0.54 respectively, p < 0.001). The overestimations in tree height are up to 16.6 m on slopes greater than 50° in our study area in Sumatra. The errors in locations (DH) and tree heights (DV) are modelled for trees with conical and spherical tree crowns. For a spherical tree crown, DH can be modelled as R sin θ, and DV as R (sec θ - 1). In this study, a model is developed for an idealised conical tree crown, DV = R (tan θ - tan ψ), where R is the crown radius, and θ and ψ are terrain and crown angles respectively. It is shown that errors occur only when terrain angle exceeds the crown angle, with the horizontal displacement equal to the crown radius. Errors in location are seen to be greater for spherical than conical trees on slopes where crown angles of conical trees are less than the terrain angle. The results are especially relevant for biomass and carbon stock estimations in tropical forests where there are trees with large crown radii on slopes.

Study for Air Vehicles at High Speeds, Identifying the Potential Benefits to Transport Aircraft of a Continuously Variable Geometry Trailing-Edge Structure that can be Utilized for Aircraft Control, Trim, Load-Alleviation, and High Lift

DTIC Science & Technology

2011-08-01

Field Length is defined as the total distance from brake release to the point at which the aircraft clears a height of 35 ft. The clearance height is...height clearance. The AEFL comprises two parts, the ground roll from brake release to lift-off (GR) plus the distance from lift-off to 35 ft height

Effect of Surface Roughness on Characteristics of Spherical Shock Waves

NASA Technical Reports Server (NTRS)

Huber, Paul W.; McFarland, Donald R.

1959-01-01

Measurements of peak overpressure and Mach stem height were made at four burst heights. Data were obtained with instrumentation capable of directly observing the variation of shock wave movement with time. Good similarity of free air shock peak overpressure with larger scale data was found to exist. The net effect of surface roughness on shock peak overpressures slightly. Surface roughness delayed the Mach stem formation at the greatest charge height and lowered the growth at all burst heights. A similarity parameter was found which approximately correlates the triple point path at different burst heights.

A stereotaxic method of recording from single neurons in the intact in vivo eye of the cat.

PubMed

Molenaar, J; Van de Grind, W A

1980-04-01

A method is described for recording stereotaxically from single retinal neurons in the optically intact in vivo eye of the cat. The method is implemented with the help of a new type of stereotaxic instrument and a specially developed stereotaxic atlas of the cat's eye and retina. The instrument is extremely stable and facilitates intracellular recording from retinal neurons. The microelectrode can be rotated about two mutually perpendicular axes, which intersect in the freely positionable pivot point of the electrode manipulation system. When the pivot point is made to coincide with a small electrode-entrance hole in the sclera of the eye, a large retinal region can be reached through this fixed hole in the immobilized eye. The stereotaxic method makes it possible to choose a target point on the presented eye atlas and predict the settings of the instrument necessary to reach this target. This method also includes the prediction of the corresponding light stimulus position on a tangent screen and the calculation of the projection of the recording electrode on this screen. The sources of error in the method were studied experimentally and a numerical perturbation analysis was carried out to study the influence of each of the sources of error on the final result. The overall accuracy of the method is of the order of 5 degrees of visual angle, which will be sufficient for most purposes.

In defense of the classical height system

NASA Astrophysics Data System (ADS)

Foroughi, Ismael; Vaníček, Petr; Sheng, Michael; Kingdon, Robert William; Santos, Marcelo C.

2017-11-01

In many European countries, normal heights referred to the quasi-geoid as introduced by Molodenskij in the mid-20th century are preferred to the classical height system that consists of orthometric heights and the geoid as a reference surface for these heights. The rationale for this choice is supposed to be that in the classical height system, neither the geoid, nor the orthometric height can be ever known with centimetre level accuracy because one would need to know the topographical mass density to a level that can never be achieved. The aim of this paper is to question the validity of this rationale. The common way of assessing the congruency of a local geoid model and the orthometric heights is to compare the geoid heights with the difference between orthometric heights provided by leveling and geodetic heights provided by GNSS. On the other hand, testing the congruency of a quasi-geoidal model with normal height a similar procedure is used, except that instead of orthometric heights, normal heights are employed. For the area of Auvergne, France, which is now a more or less standard choice for precise geoid or quasi-geoid testing, only the normal heights are supplied by the Institute Geographic National, the provider of the data. This is clearly the consequence of the European preference for the Molodenskij system. The quality of the height system is to be judged by the congruency of the difference of the geoid/quasi-geoid heights subtracted from the geodetic heights and orthometric/normal heights. To assess the congruency of the classical height system, the Helmert approximation of orthometric heights is typically used as the transformation between normal and Helmert's heights is easily done. However, the evaluation of the differences between Helmert's and the rigorous orthometric heights is somewhat more involved as will be seen from the review in this paper. For the area of interest, the differences between normal and Helmert's heights at the control leveling points range between - 9.5 and 0 cm, differences between Helmert's and the rigorous orthometric heights vary between - 3.6 and 1.1 cm. The local gravimetric geoid model of Auvergne, computed by the Stokes-Helmert technique, is used here to illustrate the accuracy of the classical height system. Results show a very reasonable standard deviation (STD) of 3.2 cm of the differences between geoid values, derived from control leveling points, and gravimetric geoid heights when Helmert's heights are employed and even a smaller STD of 2.9 cm when rigorous orthometric heights are used. A corresponding comparison of a quasi-geoid model, computed by Least-Squares Modification of Stokes method, with normal heights show an STD of 3.4 cm.

A new method of building footprints detection using airborne laser scanning data and multispectral image

NASA Astrophysics Data System (ADS)

Luo, Yiping; Jiang, Ting; Gao, Shengli; Wang, Xin

2010-10-01

It presents a new approach for detecting building footprints in a combination of registered aerial image with multispectral bands and airborne laser scanning data synchronously obtained by Leica-Geosystems ALS40 and Applanix DACS-301 on the same platform. A two-step method for building detection was presented consisting of selecting 'building' candidate points and then classifying candidate points. A digital surface model(DSM) derived from last pulse laser scanning data was first filtered and the laser points were classified into classes 'ground' and 'building or tree' based on mathematic morphological filter. Then, 'ground' points were resample into digital elevation model(DEM), and a Normalized DSM(nDSM) was generated from DEM and DSM. The candidate points were selected from 'building or tree' points by height value and area threshold in nDSM. The candidate points were further classified into building points and tree points by using the support vector machines(SVM) classification method. Two classification tests were carried out using features only from laser scanning data and associated features from two input data sources. The features included height, height finite difference, RGB bands value, and so on. The RGB value of points was acquired by matching laser scanning data and image using collinear equation. The features of training points were presented as input data for SVM classification method, and cross validation was used to select best classification parameters. The determinant function could be constructed by the classification parameters and the class of candidate points was determined by determinant function. The result showed that associated features from two input data sources were superior to features only from laser scanning data. The accuracy of more than 90% was achieved for buildings in first kind of features.

A pivot mutation impedes reverse evolution across an adaptive landscape for drug resistance in Plasmodium vivax.

PubMed

Ogbunugafor, C Brandon; Hartl, Daniel

2016-01-25

The study of reverse evolution from resistant to susceptible phenotypes can reveal constraints on biological evolution, a topic for which evolutionary theory has relatively few general principles. The public health catastrophe of antimicrobial resistance in malaria has brought these constraints on evolution into a practical realm, with one proposed solution: withdrawing anti-malarial medication use in high resistance settings, built on the assumption that reverse evolution occurs readily enough that populations of pathogens may revert to their susceptible states. While past studies have suggested limits to reverse evolution, there have been few attempts to properly dissect its mechanistic constraints. Growth rates were determined from empirical data on the growth and resistance from a set of combinatorially complete set of mutants of a resistance protein (dihydrofolate reductase) in Plasmodium vivax, to construct reverse evolution trajectories. The fitness effects of individual mutations were calculated as a function of drug environment, revealing the magnitude of epistatic interactions between mutations and genetic backgrounds. Evolution across the landscape was simulated in two settings: starting from the population fixed for the quadruple mutant, and from a polymorphic population evenly distributed between double mutants. A single mutation of large effect (S117N) serves as a pivot point for evolution to high resistance regions of the landscape. Through epistatic interactions with other mutations, this pivot creates an epistatic ratchet against reverse evolution towards the wild type ancestor, even in environments where the wild type is the most fit of all genotypes. This pivot mutation underlies the directional bias in evolution across the landscape, where evolution towards the ancestor is precluded across all examined drug concentrations from various starting points in the landscape. The presence of pivot mutations can dictate dynamics of evolution across adaptive landscape through epistatic interactions within a protein, leaving a population trapped on local fitness peaks in an adaptive landscape, unable to locate ancestral genotypes. This irreversibility suggests that the structure of an adaptive landscape for a resistance protein should be understood before considering resistance management strategies. This proposed mechanism for constraints on reverse evolution corroborates evidence from the field indicating that phenotypic reversal often occurs via compensatory mutation at sites independent of those associated with the forward evolution of resistance. Because of this, molecular methods that identify resistance patterns via single SNPs in resistance-associated markers might be missing signals for resistance and compensatory mutation throughout the genome. In these settings, whole genome sequencing efforts should be used to identify resistance patterns, and will likely reveal a more complicated genomic signature for resistance and susceptibility, especially in settings where anti-malarial medications have been used intermittently. Lastly, the findings suggest that, given their role in dictating the dynamics of evolution across the landscape, pivot mutations might serve as future targets for therapy.

Early outcomes with a single-sided access endovascular stent.

PubMed

Hofmann, Michael; Pecoraro, Felice; Planer, David; Pfammatter, Thomas; Puippe, Gilbert; Bettex, Dominique; Veith, Frank J; Lachat, Mario; Chaykovska, Lyubov

2018-03-27

The objective of this study was to report the 1-year follow-up study results of the new Horizon stent graft (Endospan, Herzliya, Israel) from two different prospective consecutive trials. The Horizon abdominal aortic aneurysm stent graft system is a 14F profile system requiring only a single access site. It consists of three modules, introduced separately: base limb (iliac to iliac limb); distal aortic limb; and proximal aortic limb with a bare suprarenal crown and active fixation. Data from the first in man (FIM) clinical study with 10 patients enrolled and the pivotal study with 30 patients were analyzed. Outcomes measured were freedom from major adverse events (MAEs) including all-cause mortality, myocardial infarction, renal failure, respiratory failure, paraplegia, stroke, bowel ischemia, and procedural blood loss ≥1000 mL. Performance end points included successful delivery and deployment of the device, freedom from aneurysm growth ≥5 mm, type I or type III endoleak, stent graft occlusion, conversion to open surgery, rupture, and stent graft migration. In the FIM study, one conversion to open surgery with >1000 mL of blood loss was registered perioperatively. In the pivotal study, no perioperative MAE was registered. Overall, at 1-year follow-up, two deaths and one aneurysm growth unrelated to endoleak were registered. The results of both the FIM and pivotal studies demonstrated that 39 of 40 procedures were successful for delivery and deployment of the Horizon stent graft. No MAE was registered during the follow-up. The primary safety and performance end points were met in both studies. Copyright © 2018 Society for Vascular Surgery. Published by Elsevier Inc. All rights reserved.

Evaluation of a depth proportional intake device for automatic pumping samplers

Treesearch

Rand E. Eads; Robert B. Thomas

1983-01-01

Abstract - A depth proportional intake boom for portable pumping samplers was used to collect suspended sediment samples in two coastal streams for three winters. The boom pivots on the stream bed while a float on the downstream end allows debris to depress the boom and pass without becoming trapped. This equipment modifies point sampling by maintaining the intake...

Children's Transitions to School: "So What about the Parents?" or "So, What about the Parents?"

ERIC Educational Resources Information Center

Webb, Grant; Knight, Bruce Allen; Busch, Gillian

2017-01-01

Children progress through a number of life transitions and each is a pivotal point of development and growth for them, their parents and family members. Through a review of the literature, the Bioecological Model will be used to frame childhood transitions as highly social, contextualised and political. This paper will assert that governments,…

Gratification: A Pivotal Point in Psychotherapy. University of Maryland Counseling Center Research Report No. 1-77.

ERIC Educational Resources Information Center

Gelso, Charles J.

This theoretical paper is based on the premise that nearly all people who enter therapy do so, to varying degrees, with the wish (conscious or unconscious demand) to have dependent longing and affectional needs gratified in the therapy itself. The conditions under, and the extent to which, the therapist provides direct gratification are crucial…

This House [Can't] Believe: Resolutional Reform in Parliamentary Debate.

ERIC Educational Resources Information Center

Stroud, Scott R.

Forensic educators stand at a pivotal point in the development of National Parliamentary Debate Association (NPDA) debate culture and standards; we have enough experience behind us to see where NPDA is going, but not so much "tradition" as to enslave us to the past. One area of reform that is highlighted by this paper is the removal of…

An automated data collection system for a Charpy impact tester

NASA Technical Reports Server (NTRS)

Weigman, Bernard J.; Spiegel, F. Xavier

1993-01-01

A method for automated data collection has been developed for a Charpy impact tester. A potentiometer is connected to the pivot point of the hammer and measures the angular displacement of the hammer. This data is collected with a computer and, through appropriate software, accurately records the energy absorbed by the specimen. The device can be easily calibrated with minimal effort.

Teeter-Totters Have Two Ends

ERIC Educational Resources Information Center

Popham, W. James

2013-01-01

The author recalls that as a child, he grooved on teeter-totters. Also known as a seesaw, a teeter-totter is a long, narrow board that's elevated with a pivot point in the middle so that as one end goes down the other end goes up. When going up or going down, sometimes quite rapidly, teeter-totters can provide their two riders with some…

A Quantitative Comparative Analysis of Ninth Grade Academies and Graduation Rates in Texas High Schools

ERIC Educational Resources Information Center

Lyons, Guy Kevin

2014-01-01

Students face many challenges in the transition to high school. From pressures of high-stakes testing for graduation to transitioning to the high school environment, many diversions can delay or even stop a student's path to graduation. Ninth-grade students are at a pivotal point in their educational careers, and a successful transition to high…

Rumour Has It: The Impact of Maternal Talk on Primary School Choice for Children Diagnosed with Autism

ERIC Educational Resources Information Center

Lilley, Rozanna

2015-01-01

This article explores the pivotal role of rumour in shaping primary school choice decisions for parents of children diagnosed with autism. Drawing on semi-structured interviews with 22 mothers conducted in Sydney, Australia, this study points to the varied functions of grapevine knowledge about schools gleaned in diverse contexts, including early…

The Impact of Single-Gender Scheduling on Students in a Title I School

ERIC Educational Resources Information Center

Moss, Janet L.

2011-01-01

This dissertation was designed to examine the impact that single-gender scheduling would have on students who attend a struggling Title I middle school. The importance of the middle level cannot be denied. Strong research points to this time in a student's life as the pivotal crux on which success and failure are balanced. Middle level educators…

CALUTRON ASSEMBLING AND DISASSEMBLING APPARATUS

DOEpatents

Andrews, R.E.

1959-01-27

The construction of a calutron tank is described, whcre the face plate of the tank carrying the ion separating mechanism may be inserted or withdrawn with a minimum of difficulty, even though the plate has considerable mass and the center of gravity of the plate assembly lies within the tank. In general, the plate is pivoted at its lower end by a specially designed hinge, whereby the weight of ths plate rests on the hinge when the plato is inserted in the tank opening. A pistoncylinder arrangement is mounted on the tank and attached at the top of the plate to produce sufficient force to pivot the plate out to a point where it withdraws by its own weight and to retard the natural tendency of the plate to close with heavy impact due to the unbalanced center of gravity of the plate assembly.

An analysis of methods for gravity determination and their utilization for the calculation of geopotential numbers in the Slovak national levelling network

NASA Astrophysics Data System (ADS)

Majkráková, Miroslava; Papčo, Juraj; Zahorec, Pavol; Droščák, Branislav; Mikuška, Ján; Marušiak, Ivan

2016-09-01

The vertical reference system in the Slovak Republic is realized by the National Levelling Network (NLN). The normal heights according to Molodensky have been introduced as reference heights in the NLN in 1957. Since then, the gravity correction, which is necessary to determine the reference heights in the NLN, has been obtained by an interpolation either from the simple or complete Bouguer anomalies. We refer to this method as the "original". Currently, the method based on geopotential numbers is the preferred way to unify the European levelling networks. The core of this article is an analysis of different ways to the gravity determination and their application for the calculation of geopotential numbers at the points of the NLN. The first method is based on the calculation of gravity at levelling points from the interpolated values of the complete Bouguer anomaly using the CBA2G_SK software. The second method is based on the global geopotential model EGM2008 improved by the Residual Terrain Model (RTM) approach. The calculated gravity is used to determine the normal heights according to Molodensky along parts of the levelling lines around the EVRF2007 datum point EH-V. Pitelová (UELN-1905325) and the levelling line of the 2nd order NLN to Kráľova hoľa Mountain (the highest point measured by levelling). The results from our analysis illustrate that the method based on the interpolated value of gravity is a better method for gravity determination when we do not know the measured gravity. It was shown that this method is suitable for the determination of geopotential numbers and reference heights in the Slovak national levelling network at the points in which the gravity is not observed directly. We also demonstrated the necessity of using the precise RTM for the refinement of the results derived solely from the EGM2008.

Multi-Pivot Quicksort: an Experiment with Single, Dual, Triple, Quad, and Penta-Pivot Quicksort Algorithms in Python

NASA Astrophysics Data System (ADS)

Budiman, M. A.; Zamzami, E. M.; Rachmawati, D.

2017-03-01

Dual-pivot quicksort, which was proposed by Yaroslavsky, has been experimentally proven to be more efficient than the classical single-pivot quicksort under the Java Virtual Machine [6]. Moreover, Kushagara, López-Ortiz, and Munro [4] has shown that triple-pivot quicksort runs 7-8% faster than dual-pivot quicksort in C, mutatis mutandis. In this research, we implement and experiment with single, dual, triple, quad, and penta-pivot quicksort algorithms in Python. Our experimental results are as follows. Firstly, the quicksort with single pivot is the slowest among the five variants. Secondly, at least until five (penta) pivots are being used, it is proven that the more pivots are used in a quicksort algorithm, the faster its performance becomes. Thirdly, the increase of speed resulted by adding more pivots tends to decrease gradually.

Spectroscopic Study of a Dark Lane and a Cool Loop in a Solar Limb Active Region by Hinode/EIS

NASA Astrophysics Data System (ADS)

Lee, Kyoung-Sun; Imada, S.; Moon, Y.-J.; Lee, Jin-Yi

2014-01-01

We investigated a cool loop and a dark lane over a limb active region on 2007 March 14 using the Hinode/EUV Imaging Spectrometer. The cool loop is clearly seen in the spectral lines formed at the transition region temperature. The dark lane is characterized by an elongated faint structure in the coronal spectral lines and is rooted on a bright point. We examined their electron densities, Doppler velocities, and nonthermal velocities as a function of distance from the limb. We derived electron densities using the density sensitive line pairs of Mg VII, Si X, Fe XII, Fe XIII, and Fe XIV spectra. We also compared the observed density scale heights with the calculated scale heights from each peak formation temperatures of the spectral lines under the hydrostatic equilibrium. We noted that the observed density scale heights of the cool loop are consistent with the calculated heights, with the exception of one observed cooler temperature; we also found that the observed scale heights of the dark lane are much lower than their calculated scale heights. The nonthermal velocity in the cool loop slightly decreases along the loop, while nonthermal velocity in the dark lane sharply falls off with height. Such a decrease in the nonthermal velocity may be explained by wave damping near the solar surface or by turbulence due to magnetic reconnection near the bright point.

Comprehensive Condition Survey and Storm Waves, Circulation, and Sedimentation Study, Dana Point Harbor, California

DTIC Science & Technology

2011-07-01

Tide on January 5, 2010 Figure 3-1 CMS-Wave Model Domain and Grid System Figure 3-2 CDIP 096 Wave and NOAA 9410660 Water Levels Figure 3-3 NDBC...Figure 3-10 Scatter plot of Observed CDIP and Hindcast Significant Wave Heights Figure 3-11 Comparison of Significant Wave Heights during the Month...obtained from the Coastal Data Information Program ( CDIP ) at Dana Point (Buoy 096) as well as the predicted tides at Newport Beach, CA (Station 9410580

NGEE Arctic Plant Traits: Shrub Transects, Kougarok Road Mile Marker 64, Seward Peninsula, Alaska, 2016

DOE Data Explorer

Verity Salmon; Colleen Iversen; Peter Thornton; Ma

2017-03-01

Transect data is from point center quarter surveys for shrub density performed in July 2016 at the Kougarok hill slope located at Kougarok Road, Mile Marker 64. For each sample point along the transects, moving averages for shrub density and shrub basal area are provided along with GPS coordinates, average shrub height and active layer depth. The individual height, basal area, and species of surveyed shrubs are also included. Data upload will be completed January 2017.

A Hybrid Approach for Characterizing Linear and Nonlinear Electromagnetic Scattering: Theory and Applications

DTIC Science & Technology

2012-11-01

axis at a 2-m height above the ground and the observation point is at a 1.7-m height along a radial line at ϕ = 30°. Ground properties: εr’ = 4...fields of a horizontal electric dipole as a function of range. The dipole is buried in the ground at a 10-cm depth and the observation point is at...would necessitate the evaluation of a triple integral. To expedite the matrix filling process, different common schemes are available in efficiently

Inflated responsibility in obsessive compulsive disorder: validation of an operational definition.

PubMed

Rhéaume, J; Ladouceur, R; Freeston, M H; Letarte, H

1995-02-01

An excessive sense of responsibility has been identified in obsessive-compulsive disorder (OCD) where patients evaluate their thoughts in terms of the harm they could cause to themselves or others. In a new definition, responsibility was defined as the belief that one possesses pivotal power to provoke or prevent subjective crucial negative outcomes. In order to empirically test the validity of this definition, two studies used a semi-idiographic design to evaluate responsibility across ambiguous situations related to major OCD themes like contamination, verification, somatic concerns, loss of control, making errors, sexuality and magical thinking. In the first study, 397 volunteer adults participated in the experiment. For each situation, subjects briefly described a possible negative outcome and then rated this outcome on four dimensions: (1) probability; (2) severity; (3) influence; and (4) pivotal influence, using a 9-point Likert scale. Finally Ss rated perceived responsibility and personal relevance. Highly relevant situations were retained for the final analysis. Regression analysis suggested that influence and pivotal influence were better predictors of responsibility ratings than probability and severity. The second study examined the effect of the order of the questions on the responsibility ratings. A first group of Ss (n = 85) answered the Responsibility Questionnaire (RQ) in the original order, while a second group (n = 53) rated responsibility before the other ratings. Regression analysis showed that although proportion of variance explained diminished when the order was reversed, pivotal influence was still the best predictor of responsibility. Results are discussed in terms of current models of OCD and implications for future research and cognitive treatment are identified.

Pivoting neuromuscular control and proprioception in females and males.

PubMed

Lee, Song Joo; Ren, Yupeng; Kang, Sang Hoon; Geiger, François; Zhang, Li-Qun

2015-04-01

Noncontact ACL injuries occur most commonly in pivoting sports and are much more frequent in females than in males. However, information on sex differences in proprioceptive acuity under weight-bearing and leg neuromuscular control in pivoting is scarce. The objective of this study was to investigate sex differences in pivoting neuromuscular control during strenuous stepping tasks and proprioceptive acuity under weight-bearing. 21 male and 22 female subjects were recruited to evaluate pivoting proprioceptive acuity under weight-bearing, and pivoting neuromuscular control (in terms of leg pivoting instability, stiffness, maximum internal and external pivoting angles, and entropy of time-to-peak EMG in lower limb muscles) during strenuous stepping tasks performed on a novel offaxis elliptical trainer. Compared to males, females had significantly lower proprioceptive acuity under weight-bearing in both internal and external pivoting directions, higher pivoting instability, larger maximum internal pivoting angle, lower leg pivoting stiffness, and higher entropy of time-to-peak EMG in the gastrocnemius muscles during strenuous stepping tasks with internal and external pivoting perturbations. Results of this study may help us better understand factors contributing to ACL injuries in females and males, develop training strategies to improve pivoting neuromuscular control and proprioceptive acuity, and potentially reduce ACL and lower-limb musculoskeletal injuries.

Anatomical recommendations for safe botulinum toxin injection into temporalis muscle: a simplified reproducible approach.

PubMed

Lee, Won-Kang; Bae, Jung-Hee; Hu, Kyung-Seok; Kato, Takafumi; Kim, Seong-Taek

2017-03-01

The objective of this study was to simplify the anatomically safe and reproducible approach for BoNT injection and to generate a detailed topographic map of the important anatomical structures of the temporal region by dividing the temporalis into nine equally sized compartments. Nineteen sides of temporalis muscle were used. The topographies of the superficial temporal artery, middle temporal vein, temporalis tendon, and the temporalis muscle were evaluated. Also evaluated was the postural relations among the foregoing anatomical structures in the temporalis muscle, pivoted upon a total of nine compartments. The temporalis above the zygomatic arch exhibited an oblique quadrangular shape with rounded upper right and left corners. The distance between the anterior and posterior margins of the temporalis muscle was equal to the width of the temporalis rectangle, and the distance between the reference line and the superior temporalis margin was equal to its height. The mean ratio of width to height was 5:4. We recommend compartments Am, Mu, and Pm (coordinates of the rectangular outline) as areas in the temporal region for BoNT injection, because using these sites will avoid large blood vessels and tendons, thus improving the safety and reproducibility of the injection.

Giant panda foraging and movement patterns in response to bamboo shoot growth.

PubMed

Zhang, Mingchun; Zhang, Zhizhong; Li, Zhong; Hong, Mingsheng; Zhou, Xiaoping; Zhou, Shiqiang; Zhang, Jindong; Hull, Vanessa; Huang, Jinyan; Zhang, Hemin

2018-03-01

Diet plays a pivotal role in dictating behavioral patterns of herbivorous animals, particularly specialist species. The giant panda (Ailuropoda melanoleuca) is well-known as a bamboo specialist. In the present study, the response of giant pandas to spatiotemporal variation of bamboo shoots was explored using field surveys and GPS collar tracking. Results show the dynamics in panda-bamboo space-time relationships that have not been previously articulated. For instance, we found a higher bamboo stump height of foraged bamboo with increasing elevation, places where pandas foraged later in spring when bamboo shoots become more fibrous and woody. The time required for shoots to reach optimum height for foraging was significantly delayed as elevation increased, a pattern which corresponded with panda elevational migration patterns beginning from the lower elevational end of Fargesia robusta distribution and gradually shifting upward until the end of the shooting season. These results indicate that giant pandas can respond to spatiotemporal variation of bamboo resources, such as available shoots. Anthropogenic interference of low-elevation F. robusta habitat should be mitigated, and conservation attention and increased monitoring should be given to F. robusta areas at the low- and mid-elevation ranges, particularly in the spring shooting season.

Transversal Fluctuations of the ASEP, Stochastic Six Vertex Model, and Hall-Littlewood Gibbsian Line Ensembles

NASA Astrophysics Data System (ADS)

Corwin, Ivan; Dimitrov, Evgeni

2018-05-01

We consider the ASEP and the stochastic six vertex model started with step initial data. After a long time, T, it is known that the one-point height function fluctuations for these systems are of order T 1/3. We prove the KPZ prediction of T 2/3 scaling in space. Namely, we prove tightness (and Brownian absolute continuity of all subsequential limits) as T goes to infinity of the height function with spatial coordinate scaled by T 2/3 and fluctuations scaled by T 1/3. The starting point for proving these results is a connection discovered recently by Borodin-Bufetov-Wheeler between the stochastic six vertex height function and the Hall-Littlewood process (a certain measure on plane partitions). Interpreting this process as a line ensemble with a Gibbsian resampling invariance, we show that the one-point tightness of the top curve can be propagated to the tightness of the entire curve.

Sensing mode atomic force microscope

DOEpatents

Hough, Paul V. C.; Wang, Chengpu

2006-08-22

An atomic force microscope is described having a cantilever comprising a base and a probe tip on an end opposite the base; a cantilever drive device connected to the base; a magnetic material coupled to the probe tip, such that when an incrementally increasing magnetic field is applied to the magnetic material an incrementally increasing force will be applied to the probe tip; a moveable specimen base; and a controller constructed to obtain a profile height of a specimen at a point based upon a contact between the probe tip and a specimen, and measure an adhesion force between the probe tip and the specimen by, under control of a program, incrementally increasing an amount of a magnetic field until a release force, sufficient to break the contact, is applied. An imaging method for atomic force microscopy involving measuring a specimen profile height and adhesion force at multiple points within an area and concurrently displaying the profile and adhesion force for each of the points is also described. A microscope controller is also described and is constructed to, for a group of points, calculate a specimen height at a point based upon a cantilever deflection, a cantilever base position and a specimen piezo position; calculate an adhesion force between a probe tip and a specimen at the point by causing an incrementally increasing force to be applied to the probe tip until the probe tip separates from a specimen; and move the probe tip to a new point in the group.

Sensing mode atomic force microscope

DOEpatents

Hough, Paul V.; Wang, Chengpu

2004-11-16

An atomic force microscope is described having a cantilever comprising a base and a probe tip on an end opposite the base; a cantilever drive device connected to the base; a magnetic material coupled to the probe tip, such that when an incrementally increasing magnetic field is applied to the magnetic material an incrementally increasing force will be applied to the probe tip; a moveable specimen base; and a controller constructed to obtain a profile height of a specimen at a point based upon a contact between the probe tip and a specimen, and measure an adhesion force between the probe tip and the specimen by, under control of a program, incrementally increasing an amount of a magnetic field until a release force, sufficient to break the contact, is applied. An imaging method for atomic force microscopy involving measuring a specimen profile height and adhesion force at multiple points within an area and concurrently displaying the profile and adhesion force for each of the points is also described. A microscope controller is also described and is constructed to, for a group of points, calculate a specimen height at a point based upon a cantilever deflection, a cantilever base position and a specimen piezo position; calculate an adhesion force between a probe tip and a specimen at the point by causing an incrementally increasing force to be applied to the probe tip until the probe tip separates from a specimen; and move the probe tip to a new point in the group.

High-Throughput Phenotyping of Plant Height: Comparing Unmanned Aerial Vehicles and Ground LiDAR Estimates.

PubMed

Madec, Simon; Baret, Fred; de Solan, Benoît; Thomas, Samuel; Dutartre, Dan; Jezequel, Stéphane; Hemmerlé, Matthieu; Colombeau, Gallian; Comar, Alexis

2017-01-01

The capacity of LiDAR and Unmanned Aerial Vehicles (UAVs) to provide plant height estimates as a high-throughput plant phenotyping trait was explored. An experiment over wheat genotypes conducted under well watered and water stress modalities was conducted. Frequent LiDAR measurements were performed along the growth cycle using a phénomobile unmanned ground vehicle. UAV equipped with a high resolution RGB camera was flying the experiment several times to retrieve the digital surface model from structure from motion techniques. Both techniques provide a 3D dense point cloud from which the plant height can be estimated. Plant height first defined as the z -value for which 99.5% of the points of the dense cloud are below. This provides good consistency with manual measurements of plant height (RMSE = 3.5 cm) while minimizing the variability along each microplot. Results show that LiDAR and structure from motion plant height values are always consistent. However, a slight under-estimation is observed for structure from motion techniques, in relation with the coarser spatial resolution of UAV imagery and the limited penetration capacity of structure from motion as compared to LiDAR. Very high heritability values ( H 2 > 0.90) were found for both techniques when lodging was not present. The dynamics of plant height shows that it carries pertinent information regarding the period and magnitude of the plant stress. Further, the date when the maximum plant height is reached was found to be very heritable ( H 2 > 0.88) and a good proxy of the flowering stage. Finally, the capacity of plant height as a proxy for total above ground biomass and yield is discussed.

Anthropometric evaluation and recommendation for primary schools classroom furniture design in Perlis

NASA Astrophysics Data System (ADS)

Shan, Lim Shaiu; Jing, Ewe Hui; Effendi, M. S. M.; Rosli, Muhamad Farizuan

2017-09-01

This study was carried out with the objective to obtain the anthropometric data of primary school children from Year 1 to Year 6 and evaluate the children's anthropometry with the current dimensions of classroom furniture (i.e. chair and table). In addition, this study also proposed the design dimensions for the improvement in classroom furniture design with the consideration of children's anthropometric data. A total of 390 children selected from 13 primary schools in Perlis, Malaysia were participated in this study. There were 11 anthropometric measurements of children have been measured in this study, which include stature (St), popliteal height (PH), knee height (KH), thigh thickness (TT), buttock popliteal length (BPL), hip breadth (HB), sitting shoulder height (SSH), sitting elbow height (SEH), forearm-hand length (FHL), height of lumbar point (HLP) and buttock clearance (BC). Besides that, 7 dimensions relating to current classroom chair have been measured, such as seat height (SH), seat depth (SD), seat width (SW), upper edge of backrest (UEB), lower edge of backrest (LEB), S point (SP), overall chair height (OCH). Another 5 dimensions of the existing classroom table have been measured too, which involve table height (TH), table depth (TD), table width (TW), under table height (UH) and seat to table clearance (STC). All the measurements were performed by using metal measuring tape. The anthropometric data of the children were analyzed with the help of Microsoft Excel 2013. Several equations with associated with the anthropometric data and furniture dimensions have been applied in this research. The new design dimensions for classroom furniture that proposed in this paper which based on the collected anthropometric data can be referred as a guideline for classroom furniture design. The implementation of these data may help to create comfortability, safety, suitability and improve performance of children in the classroom.

High-Throughput Phenotyping of Plant Height: Comparing Unmanned Aerial Vehicles and Ground LiDAR Estimates

PubMed Central

Madec, Simon; Baret, Fred; de Solan, Benoît; Thomas, Samuel; Dutartre, Dan; Jezequel, Stéphane; Hemmerlé, Matthieu; Colombeau, Gallian; Comar, Alexis

2017-01-01

The capacity of LiDAR and Unmanned Aerial Vehicles (UAVs) to provide plant height estimates as a high-throughput plant phenotyping trait was explored. An experiment over wheat genotypes conducted under well watered and water stress modalities was conducted. Frequent LiDAR measurements were performed along the growth cycle using a phénomobile unmanned ground vehicle. UAV equipped with a high resolution RGB camera was flying the experiment several times to retrieve the digital surface model from structure from motion techniques. Both techniques provide a 3D dense point cloud from which the plant height can be estimated. Plant height first defined as the z-value for which 99.5% of the points of the dense cloud are below. This provides good consistency with manual measurements of plant height (RMSE = 3.5 cm) while minimizing the variability along each microplot. Results show that LiDAR and structure from motion plant height values are always consistent. However, a slight under-estimation is observed for structure from motion techniques, in relation with the coarser spatial resolution of UAV imagery and the limited penetration capacity of structure from motion as compared to LiDAR. Very high heritability values (H2> 0.90) were found for both techniques when lodging was not present. The dynamics of plant height shows that it carries pertinent information regarding the period and magnitude of the plant stress. Further, the date when the maximum plant height is reached was found to be very heritable (H2> 0.88) and a good proxy of the flowering stage. Finally, the capacity of plant height as a proxy for total above ground biomass and yield is discussed. PMID:29230229

Locating hot and cold-legs in a nuclear powered steam generation system

DOEpatents

Ekeroth, D.E.; Corletti, M.M.

1993-11-16

A nuclear reactor steam generator includes a reactor vessel for heating water and a steam generator with a pump casing at the lowest point on the steam generator. A cold-leg pipe extends horizontally between the steam generator and the reactor vessel to return water from the steam generator to the reactor vessel. The bottom of the cold-leg pipe is at a first height above the bottom of the reactor vessel. A hot-leg pipe with one end connected to the steam generator and a second end connected to the reactor vessel has a first pipe region extending downwardly from the steam generator to a location between the steam generator and the reactor vessel at which a bottom of the hot-leg pipe is at a second height above the bottom of the reactor vessel. A second region extends from that location in a horizontal direction at the second height to the point at which the hot-leg pipe connects to the reactor vessel. A pump is attached to the casing at a location below the first and second heights and returns water from the steam generator to the reactor vessel over the cold-leg. The first height is greater than the second height and the bottom of the steam generator is at a height above the bottom of the reactor vessel that is greater than the first and second heights. A residual heat recovery pump is below the hot-leg and has an inlet line from the hot-leg that slopes down continuously to the pump inlet. 2 figures.

Locating hot and cold-legs in a nuclear powered steam generation system

DOEpatents

Ekeroth, Douglas E.; Corletti, Michael M.

1993-01-01

A nuclear reactor steam generator includes a reactor vessel for heating water and a steam generator with a pump casing at the lowest point on the steam generator. A cold-leg pipe extends horizontally between the steam generator and the reactor vessel to return water from the steam generator to the reactor vessel. The bottom of the cold-leg pipe is at a first height above the bottom of the reactor vessel. A hot-leg pipe with one end connected to the steam generator and a second end connected to the reactor vessel has a first pipe region extending downwardly from the steam generator to a location between the steam generator and the reactor vessel at which a bottom of the hot-leg pipe is at a second height above the bottom of the reactor vessel. A second region extends from that location in a horizontal direction at the second height to the point at which the hot-leg pipe connects to the reactor vessel. A pump is attached to the casing at a location below the first and second heights and returns water from the steam generator to the reactor vessel over the cold-leg. The first height is greater than the second height and the bottom of the steam generator is at a height above the bottom of the reactor vessel that is greater than the first and second heights. A residual heat recovery pump is below the hot-leg and has an inlet line from the hot-leg that slopes down continuously to the pump inlet.

Swing Weights of Baseball and Softball Bats

ERIC Educational Resources Information Center

Russell, Dan

2010-01-01

Baseball and softball bats are sold according to length in inches and weight in ounces. Much to the consternation of players buying new bats, however, not all bats that weigh the same swing the same. The reason for this has to do with moment of inertia of the bat about a pivot point on the handle, or what the sporting goods industry refers to as…

Understanding the Psychology of a Trickster Tale: 5-Year-Old Japanese Kindergarten Children Collaboratively Retelling a "Kitsune" Story

ERIC Educational Resources Information Center

Oshiro, Aiko; Pihl, Agneta; Peterson, Louise; Pramling, Niklas

2017-01-01

How children understand the psychology of a story (i.e., the intentions and experiences of its characters) is pivotal to comprehending its point. In this study we investigate empirically how 5-year-old children in a Japanese kindergarten manage mental state verbs and adjectives when collaboratively retelling a tale heard. The tale, an example of a…

Effect of Impeller Geometry on Lift-Off Characteristics and Rotational Attitude in a Monopivot Centrifugal Blood Pump.

PubMed

Nishida, Masahiro; Nakayama, Kento; Sakota, Daisuke; Kosaka, Ryo; Maruyama, Osamu; Kawaguchi, Yasuo; Kuwana, Katsuyuki; Yamane, Takashi

2016-06-01

The effect of the flow path geometry of the impeller on the lift-off and tilt of the rotational axis of the impeller against the hydrodynamic force was investigated in a centrifugal blood pump with an impeller supported by a single-contact pivot bearing. Four types of impeller were compared: the FR model with the flow path having both front and rear cutouts on the tip, the F model with the flow path having only a front cutout, the R model with only a rear cutout, and the N model with a straight flow path. First, the axial thrust and the movement about the pivot point, which was loaded on the surface of the impeller, were calculated using computational fluid dynamics (CFD) analysis. Next, the lift-off point and the tilt of the rotational axis of the impeller were measured experimentally. The CFD analysis showed that the axial thrust increased gently in the FR and R models as the flow rate increased, whereas it increased drastically in the F and N models. This difference in axial thrust was likely from the higher pressure caused by the smaller circumferential velocity in the gap between the top surface of the impeller and the casing in the FR and R models than in the F and N models, which was caused by the rear cutout. These results corresponded with the experimental results showing that the impellers lifted off in the F and N models as the flow rate increased, whereas it did not in the FR and R models. Conversely, the movement about the pivot point increased in the direction opposite the side with the pump outlet as the flow rate increased. However, the tilt of the rotational axis of the impeller, which oriented away from the pump outlet, was less than 0.8° in any model under any conditions, and was considered to negligibly affect the rotational attitude of the impeller. These results confirm that a rear cutout prevents lift-off of the impeller caused by a decrease in the axial thrust. © 2016 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.

Classification of Mobile Laser Scanning Point Clouds from Height Features

NASA Astrophysics Data System (ADS)

Zheng, M.; Lemmens, M.; van Oosterom, P.

2017-09-01

The demand for 3D maps of cities and road networks is steadily growing and mobile laser scanning (MLS) systems are often the preferred geo-data acquisition method for capturing such scenes. Because MLS systems are mounted on cars or vans they can acquire billions of points of road scenes within a few hours of survey. Manual processing of point clouds is labour intensive and thus time consuming and expensive. Hence, the need for rapid and automated methods for 3D mapping of dense point clouds is growing exponentially. The last five years the research on automated 3D mapping of MLS data has tremendously intensified. In this paper, we present our work on automated classification of MLS point clouds. In the present stage of the research we exploited three features - two height components and one reflectance value, and achieved an overall accuracy of 73 %, which is really encouraging for further refining our approach.

Spectroscopic study of a dark lane and a cool loop in a solar limb active region by Hinode/EIS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Kyoung-Sun; Imada, S.; Moon, Y.-J.

2014-01-10

We investigated a cool loop and a dark lane over a limb active region on 2007 March 14 using the Hinode/EUV Imaging Spectrometer. The cool loop is clearly seen in the spectral lines formed at the transition region temperature. The dark lane is characterized by an elongated faint structure in the coronal spectral lines and is rooted on a bright point. We examined their electron densities, Doppler velocities, and nonthermal velocities as a function of distance from the limb. We derived electron densities using the density sensitive line pairs of Mg VII, Si X, Fe XII, Fe XIII, and Femore » XIV spectra. We also compared the observed density scale heights with the calculated scale heights from each peak formation temperatures of the spectral lines under the hydrostatic equilibrium. We noted that the observed density scale heights of the cool loop are consistent with the calculated heights, with the exception of one observed cooler temperature; we also found that the observed scale heights of the dark lane are much lower than their calculated scale heights. The nonthermal velocity in the cool loop slightly decreases along the loop, while nonthermal velocity in the dark lane sharply falls off with height. Such a decrease in the nonthermal velocity may be explained by wave damping near the solar surface or by turbulence due to magnetic reconnection near the bright point.« less

Data-driven sensor placement from coherent fluid structures

NASA Astrophysics Data System (ADS)

Manohar, Krithika; Kaiser, Eurika; Brunton, Bingni W.; Kutz, J. Nathan; Brunton, Steven L.

2017-11-01

Optimal sensor placement is a central challenge in the prediction, estimation and control of fluid flows. We reinterpret sensor placement as optimizing discrete samples of coherent fluid structures for full state reconstruction. This permits a drastic reduction in the number of sensors required for faithful reconstruction, since complex fluid interactions can often be described by a small number of coherent structures. Our work optimizes point sensors using the pivoted matrix QR factorization to sample coherent structures directly computed from flow data. We apply this sampling technique in conjunction with various data-driven modal identification methods, including the proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD). In contrast to POD-based sensors, DMD demonstrably enables the optimization of sensors for prediction in systems exhibiting multiple scales of dynamics. Finally, reconstruction accuracy from pivot sensors is shown to be competitive with sensors obtained using traditional computationally prohibitive optimization methods.

Micro-fluid exchange coupling apparatus

NASA Technical Reports Server (NTRS)

Johnson, J. E., Jr.; Swartz, P. F. (Inventor)

1980-01-01

In a macro-fluid exchange, a hollow needle, such as a syringe needle, is provided for penetrating the fluid conduit of the animal. The syringe needle is coupled to a plenum chamber having an inlet and outlet port. The plenum chamber is coupled to the syringe needle via the intermediary of a standard quick disconnect coupling fitting. The plenum chamber is carried at the end of a drive rod which is coupled to a micrometer drive head. The micrometer drive head is slidably and pivotably coupled to a pedestal for adjusting the height and angle of inclination of the needle relative to a reference base support. The needle is positioned adjacent to the incised trachea or a blood vessel of a small animal and the micrometer drive head is operated for penetrating the fluid conduit of the animal.

Evolution of offshore wind waves tracked by surface drifters with a point-positioning GPS sensor

NASA Astrophysics Data System (ADS)

Komatsu, K.

2009-12-01

Wind-generated waves have been recognized as one of the most important factors of the sea surface roughness which plays crucial roles in various air-sea interactions such as energy, momentum, heat and gas exchanges. At the same time, wind waves with extreme wave heights representatively called as freak or rogue waves have been a matter of great concern for many people involved in shipping, fishing, constracting, surfing and other marine activities, because such extreme waves frequently affect on the marine activities and sometimes cause serious disasters. Nevertheless, investigations of actual conditions for the evolution of wind waves in the offshore region are less and sparse in contrast to dense monitoring networks in the coastal regions because of difficulty of offshore observation with high accuracy. Recently accurate in situ observation of offshore wind waves is getting possible at low cost owing to a wave height and direction sensor developed by Harigae et al. (2004) by installing a point-positioning GPS receiver on a surface drifting buoy. The point-positioning GPS sensor can extract three dimensional movements of the buoy excited by ocean waves with minimizing effects of GPS point-positioning errors through the use of a high-pass filter. Two drifting buoys equipped with the GPS-based wave sensor charged by solar cells were drifted in the western North Pacific and one of them continued to observe wind waves during 16 months from Sep. 2007. The RMSE of the GPS-based wave sensor was less than 10cm in significant wave height and about 1s in significant wave period in comparison with other sensors, i.e. accelerometers installed on drifting buoys of Japan Meteorological Agency, ultrasonic sensors placed at the Hiratsuka observation station of the University of Tokyo and altimeter of the JASON-1. The GPS-based wave buoys enabled us to detect freak waves defined as waves whose height is more than twice the significant wave height. The observation conducted by the wave buoys in 2007-2008 indicated a little more frequent occurrence of freak waves comparing with Forristall’s (1978) empirical formula and Naess’s (1985) distribution for a narrow-band Gaussian sea. Fig.1. Time series of the ratio of the significant wave height to the maximum wave height in 20 minutes sampling period observed by a drifting buoy with a GPS sensor

Pressure Sounding of the Middle Atmosphere from ATMOS Solar Occultation Measurements of Atmospheric CO(sub 2) Absorption Lines

NASA Technical Reports Server (NTRS)

Abrams, M.; Gunson, M.; Lowes, L.; Rinsland, C.; Zander, R.

1994-01-01

A method for retrieving the atmospheric pressure corresponding to the tangent point of an infrared spectrum recorded in the solar occultation mode is described and applied to measurements made by the Atmospheric Trace Molecule Spectroscopy (ATMOS) Fourier transform spectrometer. Tangent pressure values are inferred from measurements of isolated CO(sub 2) lines with temperature-insensitive intensities. Tangent pressures are determined with a spectroscopic precision of 1-3%, corresponding to a tangent point height precision, depending on the scale height, of 70-210 meters.

Cumulus cloud base height estimation from high spatial resolution Landsat data - A Hough transform approach

NASA Technical Reports Server (NTRS)

Berendes, Todd; Sengupta, Sailes K.; Welch, Ron M.; Wielicki, Bruce A.; Navar, Murgesh

1992-01-01

A semiautomated methodology is developed for estimating cumulus cloud base heights on the basis of high spatial resolution Landsat MSS data, using various image-processing techniques to match cloud edges with their corresponding shadow edges. The cloud base height is then estimated by computing the separation distance between the corresponding generalized Hough transform reference points. The differences between the cloud base heights computed by these means and a manual verification technique are of the order of 100 m or less; accuracies of 50-70 m may soon be possible via EOS instruments.

Characteristics of Clinical Studies Conducted Over the Total Product Life Cycle of High-Risk Therapeutic Medical Devices Receiving FDA Premarket Approval in 2010 and 2011.

PubMed

Rathi, Vinay K; Krumholz, Harlan M; Masoudi, Frederick A; Ross, Joseph S

2015-08-11

The US Food and Drug Administration (FDA) approves high-risk medical devices, those that support or sustain human life or present potential unreasonable risk to patients, via the Premarket Approval (PMA) pathway. The generation of clinical evidence to understand device safety and effectiveness is shifting from predominantly premarket to continual study throughout the total product life cycle. To characterize the clinical evidence generated for high-risk therapeutic devices over the total product life cycle. All clinical studies of high-risk therapeutic devices receiving initial market approval via the PMA pathway in 2010 and 2011 identified through ClinicalTrials.gov and publicly available FDA documents as of October 2014. Studies were characterized by type (pivotal, studies that served as the basis of FDA approval; FDA-required postapproval studies [PAS]; or manufacturer/investigator-initiated); premarket or postmarket; status (completed, ongoing, or terminated/unknown); and design features, including enrollment, comparator, and longest duration of primary effectiveness end point follow-up. In 2010 and 2011, 28 high-risk therapeutic devices received initial marketing approval via the PMA pathway. We identified 286 clinical studies of these devices: 82 (28.7%) premarket and 204 (71.3%) postmarket, among which there were 52 (18.2%) nonpivotal premarket studies, 30 (10.5%) pivotal premarket studies, 33 (11.5%) FDA-required PAS, and 171 (59.8%) manufacturer/investigator-initiated postmarket studies. Six of 33 (18.2%) PAS and 20 of 171 (11.7%) manufacturer/investigator-initiated postmarket studies were reported as completed. No postmarket studies were identified for 5 (17.9%) devices; 3 or fewer were identified for 13 (46.4%) devices overall. Median enrollment was 65 patients (interquartile range [IQR], 25-111), 241 patients (IQR, 147-415), 222 patients (IQR, 119-640), and 250 patients (IQR, 60-800) for nonpivotal premarket, pivotal, FDA-required PAS, and manufacturer/investigator-initiated postmarket studies, respectively. Approximately half of all studies used no comparator (pivotal: 13/30 [43.3%]; completed postmarket: 16/26 [61.5%]; ongoing postmarket: 70/153 [45.8%]). Median duration of primary effectiveness end point follow-up was 3.0 months (IQR, 3.0-12.0), 9.0 months (IQR, 0.3-12.0), and 12.0 months (IQR, 7.0-24.0) for pivotal, completed postmarket, and ongoing postmarket studies, respectively. Among high-risk therapeutic devices approved via the FDA PMA pathway, total product life cycle evidence generation varied in both the number and quality of premarket and postmarket studies, with approximately 13% of initiated postmarket studies completed between 3 and 5 years after FDA approval.

a Comparitive Study Using Geometric and Vertical Profile Features Derived from Airborne LIDAR for Classifying Tree Genera

NASA Astrophysics Data System (ADS)

Ko, C.; Sohn, G.; Remmel, T. K.

2012-07-01

We present a comparative study between two different approaches for tree genera classification using descriptors derived from tree geometry and those derived from the vertical profile analysis of LiDAR point data. The different methods provide two perspectives for processing LiDAR point clouds for tree genera identification. The geometric perspective analyzes individual tree crowns in relation to valuable information related to characteristics of clusters and line segments derived within crowns and overall tree shapes to highlight the spatial distribution of LiDAR points within the crown. Conversely, analyzing vertical profiles retrieves information about the point distributions with respect to height percentiles; this perspective emphasizes of the importance that point distributions at specific heights express, accommodating for the decreased point density with respect to depth of canopy penetration by LiDAR pulses. The targeted species include white birch, maple, oak, poplar, white pine and jack pine at a study site northeast of Sault Ste. Marie, Ontario, Canada.

46 CFR 45.69 - Correction for bow height.

Code of Federal Regulations, 2010 CFR

2010-10-01

... least 15 percent of the length of the vessel measured from the forward perpendicular. (c) Where the bow... point at least 0.06 L abaft the forward perpendicular. (d) Vessels which, to suit exceptional... consideration by the Commandant. (e) The bow height is defined as the vertical distance at the forward...

46 CFR 45.69 - Correction for bow height.

Code of Federal Regulations, 2011 CFR

2011-10-01

... least 15 percent of the length of the vessel measured from the forward perpendicular. (c) Where the bow... point at least 0.06 L abaft the forward perpendicular. (d) Vessels which, to suit exceptional... consideration by the Commandant. (e) The bow height is defined as the vertical distance at the forward...

Point Judith, Rhode Island, Breakwater Risk Assessment

DTIC Science & Technology

2015-08-01

output stations. Beach zones considered included the sandy beach to the west side of the HoR, which had significant dune features and was fronting...time dependency for crest height and wave parameters is assumed, hc = total damaged crest height of structure from toe , Lp is the local wave length...computed using linear wave theory and Tp, h is the toe depth, hc’ = total undamaged crest height of structure from toe , At = area of structure enclosed

Automatic tree parameter extraction by a Mobile LiDAR System in an urban context.

PubMed

Herrero-Huerta, Mónica; Lindenbergh, Roderik; Rodríguez-Gonzálvez, Pablo

2018-01-01

In an urban context, tree data are used in city planning, in locating hazardous trees and in environmental monitoring. This study focuses on developing an innovative methodology to automatically estimate the most relevant individual structural parameters of urban trees sampled by a Mobile LiDAR System at city level. These parameters include the Diameter at Breast Height (DBH), which was estimated by circle fitting of the points belonging to different height bins using RANSAC. In the case of non-circular trees, DBH is calculated by the maximum distance between extreme points. Tree sizes were extracted through a connectivity analysis. Crown Base Height, defined as the length until the bottom of the live crown, was calculated by voxelization techniques. For estimating Canopy Volume, procedures of mesh generation and α-shape methods were implemented. Also, tree location coordinates were obtained by means of Principal Component Analysis. The workflow has been validated on 29 trees of different species sampling a stretch of road 750 m long in Delft (The Netherlands) and tested on a larger dataset containing 58 individual trees. The validation was done against field measurements. DBH parameter had a correlation R2 value of 0.92 for the height bin of 20 cm which provided the best results. Moreover, the influence of the number of points used for DBH estimation, considering different height bins, was investigated. The assessment of the other inventory parameters yield correlation coefficients higher than 0.91. The quality of the results confirms the feasibility of the proposed methodology, providing scalability to a comprehensive analysis of urban trees.

Automatic tree parameter extraction by a Mobile LiDAR System in an urban context

PubMed Central

Lindenbergh, Roderik; Rodríguez-Gonzálvez, Pablo

2018-01-01

In an urban context, tree data are used in city planning, in locating hazardous trees and in environmental monitoring. This study focuses on developing an innovative methodology to automatically estimate the most relevant individual structural parameters of urban trees sampled by a Mobile LiDAR System at city level. These parameters include the Diameter at Breast Height (DBH), which was estimated by circle fitting of the points belonging to different height bins using RANSAC. In the case of non-circular trees, DBH is calculated by the maximum distance between extreme points. Tree sizes were extracted through a connectivity analysis. Crown Base Height, defined as the length until the bottom of the live crown, was calculated by voxelization techniques. For estimating Canopy Volume, procedures of mesh generation and α-shape methods were implemented. Also, tree location coordinates were obtained by means of Principal Component Analysis. The workflow has been validated on 29 trees of different species sampling a stretch of road 750 m long in Delft (The Netherlands) and tested on a larger dataset containing 58 individual trees. The validation was done against field measurements. DBH parameter had a correlation R2 value of 0.92 for the height bin of 20 cm which provided the best results. Moreover, the influence of the number of points used for DBH estimation, considering different height bins, was investigated. The assessment of the other inventory parameters yield correlation coefficients higher than 0.91. The quality of the results confirms the feasibility of the proposed methodology, providing scalability to a comprehensive analysis of urban trees. PMID:29689076

Remote controlled vacuum joint closure mechanism

DOEpatents

Doll, D.W.; Hager, E.R.

1984-02-22

A remotely operable and maintainable vacuum joint closure mechanism for a noncircular aperture is disclosed. The closure mechanism includes an extendible bellows coupled at one end to a noncircular duct and at its other end to a flange assembly having sealed grooves for establishing a high vacuum seal with the abutting surface of a facing flange which includes an aperture forming part of the system to be evacuated. A plurality of generally linear arrangements of pivotally coupled linkages and piston combinations are mounted around the outer surface of the duct and aligned along the length thereof. Each of the piston/linkage assemblies is adapted to engage the flange assembly by means of a respective piston and is further coupled to a remote controlled piston drive shaft to permit each of the linkages positioned on a respective flat outer surface of the duct to simultaneously and uniformly displace a corresponding piston and the flange assembly with which it is in contact along the length of the duct in extending the bellows to provide a high vacuum seal between the movable flange and the facing flange. A plurality of latch mechanisms are also pivotally mounted on the outside of the duct. A first end of each of the latch mechanisms is coupled to a remotely controlled latch control shaft for displacing the latch mechanism about its pivot point. In response to the pivoting displacement of the latch mechanism, a second end thereof is displaced so as to securely engage the facing flange and maintain the high vacuum seal established by the displacement of the flange assembly and extension of the bellows without displacing the entire duct.

Height Dependence of Plasma Properties of a Dark Lane and a Cool Loop in a Solar Limb Active Region Observed by Hinode/EIS

NASA Astrophysics Data System (ADS)

Lee, K.; Imada, S.; Moon, Y.; Lee, J.

2013-12-01

We investigate spectral properties of a cool loop and a dark lane over a limb active region on 2007 March 14 by the Hinode/EUV Imaging Spectrometer. The cool loop is clearly seen in the spectral lines formed at the transition region temperature. The dark lane is characterized by an elongated faint structure in coronal spectral lines and rooted on a bright point. We determine their electron densities, Doppler velocities, and non-thermal velocities with height over the limb. We derived electron densities using the density sensitive line pairs of Mg VII, Si X, Fe XII, Fe XIII and Fe XIV spectra. Under the hydrostatic equilibrium and isothermal assumption, we determine their temperatures from the density scale height. Comparing the scale height temperatures to the peak formation temperatures of the spectral lines, we note that the scale height temperature of the cool loop is consistent with a peak formation temperature of the Fe XII and the scale height temperatures of the dark lane from each spectral lines are much lower than their peak formation temperatures. The non-thermal velocity in the cool loop slightly decreases along the loop while that in the dark lane sharply falls off with height. The variation of non-thermal velocity with height in the cool loop and the dark lane is contrast to that in off-limb polar coronal holes which are considered as source of the solar wind. Such a decrease in the non-thermal velocity may be explained by wave damping near the solar surface or turbulence due to magnetic reconnection near the bright point.

Full Spectrum Crashworthiness Criteria for Rotorcraft

DTIC Science & Technology

2011-12-01

hydraulic orifice and metering pin technologies. One drawback of this technology is that the shock strut loads can exceed the design strength allowable...where the velocity v is to be computed. For example, using a pendulum -style swing method for full-scale aircraft crash tests introduces a pitch...performed at LandIR using a parallel pendulum swing technique (Figure 6-10). Equidistant pivot-point platforms are located at the top of the gantry

From Pivot to Symmetry Integrating Africa in the Rebalance to Asia

DTIC Science & Technology

2014-02-13

point of view, the competition is already lost, as a natural evolution of the global balance of powers. In that case, the American laissez - faire ...prioritize its involvements across the globe in an environment of finite resources. In this regard, the subsequent international leadership void...capitalizing on burden sharing and distributive leadership among allies and African partners, avoiding the pitfalls of bluntly and unilaterally imposed

Investing in Change: The Walton Family Foundation Charts a New Course. Principles for Effective Education Grantmaking. Case Study No. 12

ERIC Educational Resources Information Center

Wisdom, Michelle

2015-01-01

The Walton Family Foundation was at a pivotal point in early 2015. After investing $1.3 billion in K-12 education over the previous two decades, executive and board leadership were reflecting on past work, and charting a course for the Foundation's strategic direction based on key learnings from their investments in education. The Walton Family…

The CardiAMP Heart Failure trial: A randomized controlled pivotal trial of high-dose autologous bone marrow mononuclear cells using the CardiAMP cell therapy system in patients with post-myocardial infarction heart failure: Trial rationale and study design.

PubMed

Raval, Amish N; Cook, Thomas D; Duckers, Henricus J; Johnston, Peter V; Traverse, Jay H; Abraham, William T; Altman, Peter A; Pepine, Carl J

2018-07-01

Heart failure following myocardial infarction is a common, disabling, and deadly condition. Direct injection of autologous bone marrow mononuclear cells into the myocardium may result in improved functional recovery, relieve symptoms, and improve other cardiovascular outcomes. CardiAMP-HF is a randomized, double-blind, sham-controlled, pivotal trial designed to investigate the safety and efficacy of autologous bone marrow mononuclear cells treatment for patients with medically refractory and symptomatic ischemic cardiomyopathy. The primary end point is change in 6-minute walk distance adjusted for major adverse cardiovascular events at 12 months following treatment. Particularly novel aspects of this trial include a cell potency assay to screen subjects who have bone marrow cell characteristics that suggest a favorable response to treatment, a point-of-care treatment method, a high target dose of 200 million cells, and an efficient transcatheter intramyocardial delivery method that is associated with high cell retention. This novel approach may lead to a new treatment for those with ischemic heart disease suffering from medically refractory heart failure. Copyright © 2018 Elsevier Inc. All rights reserved.

Topographic mapping using a monopulse SAR system

NASA Technical Reports Server (NTRS)

Zink, M.; Oettl, H.; Freeman, A.

1993-01-01

Terrain height variations in mountainous areas cause two problems in the radiometric correction of SAR images: the first being that the wrong elevation angle may be used in correcting for the radiometric variation of the antenna pattern; the second that the local incidence angle used in correcting the projection of the pixel area from slant range to ground range coordinates may vary from that given by the flat earth assumption. We propose a novel design of a SAR system which exploits the monopulse principle to determine the elevation angle and thus the height at the different parts of the image. The key element of such a phase monopulse system is an antenna, which can be divided into a lower and upper half in elevation using a monopulse comparator. In addition to the usual sum pattern, the elevation difference pattern can be generated by a -pi phase shift on one half of the antenna. From the ratios of images radiometrically modulated by the difference and sum antenna pattern in cross-track direction, we can derive the appropriate elevation angle at any point in the image. Together with the slant range we can calculate the height of the platform above this point using information on the antenna pointing and the platform attitude. This operation, repeated at many locations throughout the image, allows us to build up a topographic map of the height of the aircraft above each location. Inversion of this map, using the precisely determined aircraft altitude and the accurate flight path, leads to the actual topography of the imaged surface. The precise elevation of one point in the image could also be used to convert the height map to a topographic map. In this paper, we present design considerations for a corresponding airborne SAR system in X-Band and give estimates of the error due to system noise and azimuth ambiguities as well as the expected performance and precision in topographic mapping.

14 CFR 29.59 - Takeoff path: Category A.

Code of Federal Regulations, 2010 CFR

2010-01-01

... addition— (1) The takeoff path must remain clear of the height-velocity envelope established in accordance with § 29.87; (2) The rotorcraft must be flown to the engine failure point; at which point, the...

Automatic determination of trunk diameter, crown base and height of scots pine (Pinus Sylvestris L.) Based on analysis of 3D point clouds gathered from multi-station terrestrial laser scanning. (Polish Title: Automatyczne okreslanie srednicy pnia, podstawy korony oraz wysokosci sosny zwyczajnej (Pinus Silvestris L.) Na podstawie analiz chmur punktow 3D pochodzacych z wielostanowiskowego naziemnego skanowania laserowego)

NASA Astrophysics Data System (ADS)

Ratajczak, M.; Wężyk, P.

2015-12-01

Rapid development of terrestrial laser scanning (TLS) in recent years resulted in its recognition and implementation in many industries, including forestry and nature conservation. The use of the 3D TLS point clouds in the process of inventory of trees and stands, as well as in the determination of their biometric features (trunk diameter, tree height, crown base, number of trunk shapes), trees and lumber size (volume of trees) is slowly becoming a practice. In addition to the measurement precision, the primary added value of TLS is the ability to automate the processing of the clouds of points 3D in the direction of the extraction of selected features of trees and stands. The paper presents the original software (GNOM) for the automatic measurement of selected features of trees, based on the cloud of points obtained by the ground laser scanner FARO. With the developed algorithms (GNOM), the location of tree trunks on the circular research surface was specified and the measurement was performed; the measurement covered the DBH (l: 1.3m), further diameters of tree trunks at different heights of the tree trunk, base of the tree crown and volume of the tree trunk (the selection measurement method), as well as the tree crown. Research works were performed in the territory of the Niepolomice Forest in an unmixed pine stand (Pinussylvestris L.) on the circular surface with a radius of 18 m, within which there were 16 pine trees (14 of them were cut down). It was characterized by a two-storey and even-aged construction (147 years old) and was devoid of undergrowth. Ground scanning was performed just before harvesting. The DBH of 16 pine trees was specified in a fully automatic way, using the algorithm GNOM with an accuracy of +2.1%, as compared to the reference measurement by the DBH measurement device. The medium, absolute measurement error in the cloud of points - using semi-automatic methods "PIXEL" (between points) and PIPE (fitting the cylinder) in the FARO Scene 5.x., showed the error, 3.5% and 5.0%,.respectively The reference height was assumed as the measurement performed by the tape on the cut tree. The average error of automatic determination of the tree height by the algorithm GNOM based on the TLS point clouds amounted to 6.3% and was slightly higher than when using the manual method of measurements on profiles in the TerraScan (Terrasolid; the error of 5.6%). The relatively high value of the error may be mainly related to the small number of points TLS in the upper parts of crowns. The crown height measurement showed the error of +9.5%. The reference in this case was the tape measurement performed already on the trunks of cut pine trees. Processing the clouds of points by the algorithms GNOM for 16 analyzed trees took no longer than 10 min. (37 sec. /tree). The paper mainly showed the TLS measurement innovation and its high precision in acquiring biometric data in forestry, and at the same time also the further need to increase the degree of automation of processing the clouds of points 3D from terrestrial laser scanning.

Relative variances of the cadence frequency of cycling under two differential saddle heights

PubMed Central

Chang, Wen-Dien; Fan Chiang, Chin-Yun; Lai, Ping-Tung; Lee, Chia-Lun; Fang, Sz-Ming

2016-01-01

[Purpose] Bicycle saddle height is a critical factor for cycling performance and injury prevention. The present study compared the variance in cadence frequency after exercise fatigue between saddle heights with 25° and 35° knee flexion. [Methods] Two saddle heights, which were determined by setting the pedal at the bottom dead point with 35° and 25° knee flexion, were used for testing. The relative variances of the cadence frequency were calculated at the end of a 5-minute warm-up period and 5 minutes after inducing exercise fatigue. Comparison of the absolute values of the cadence frequency under the two saddle heights revealed a difference in pedaling efficiency. [Results] Five minutes after inducing exercise fatigue, the relative variances of the cadence frequency for the saddle height with 35° knee flexion was higher than that for the saddle height with 25° knee flexion. [Conclusion] The current finding demonstrated that a saddle height with 25° knee flexion is more appropriate for cyclists than a saddle height with 35° knee flexion. PMID:27065522

Problems and Limitations of Satellite Image Orientation for Determination of Height Models

NASA Astrophysics Data System (ADS)

Jacobsen, K.

2017-05-01

The usual satellite image orientation is based on bias corrected rational polynomial coefficients (RPC). The RPC are describing the direct sensor orientation of the satellite images. The locations of the projection centres today are without problems, but an accuracy limit is caused by the attitudes. Very high resolution satellites today are very agile, able to change the pointed area over 200km within 10 to 11 seconds. The corresponding fast attitude acceleration of the satellite may cause a jitter which cannot be expressed by the third order RPC, even if it is recorded by the gyros. Only a correction of the image geometry may help, but usually this will not be done. The first indication of jitter problems is shown by systematic errors of the y-parallaxes (py) for the intersection of corresponding points during the computation of ground coordinates. These y-parallaxes have a limited influence to the ground coordinates, but similar problems can be expected for the x-parallaxes, determining directly the object height. Systematic y-parallaxes are shown for Ziyuan-3 (ZY3), WorldView-2 (WV2), Pleiades, Cartosat-1, IKONOS and GeoEye. Some of them have clear jitter effects. In addition linear trends of py can be seen. Linear trends in py and tilts in of computed height models may be caused by limited accuracy of the attitude registration, but also by bias correction with affinity transformation. The bias correction is based on ground control points (GCPs). The accuracy of the GCPs usually does not cause some limitations but the identification of the GCPs in the images may be difficult. With 2-dimensional bias corrected RPC-orientation by affinity transformation tilts of the generated height models may be caused, but due to large affine image deformations some satellites, as Cartosat-1, have to be handled with bias correction by affinity transformation. Instead of a 2-dimensional RPC-orientation also a 3-dimensional orientation is possible, respecting the object height more as by 2-dimensional orientation. The 3-dimensional orientation showed advantages for orientation based on a limited number of GCPs, but in case of poor GCP distribution it may cause also negative effects. For some of the used satellites the bias correction by affinity transformation showed advantages, but for some other the bias correction by shift was leading to a better levelling of the generated height models, even if the root mean square (RMS) differences at the GCPs were larger as for bias correction by affinity transformation. The generated height models can be analyzed and corrected with reference height models. For the used data sets accurate reference height models are available, but an analysis and correction with the free of charge available SRTM digital surface model (DSM) or ALOS World 3D (AW3D30) is also possible and leads to similar results. The comparison of the generated height models with the reference DSM shows some height undulations, but the major accuracy influence is caused by tilts of the height models. Some height model undulations reach up to 50 % of the ground sampling distance (GSD), this is not negligible but it cannot be seen not so much at the standard deviations of the height. In any case an improvement of the generated height models is possible with reference height models. If such corrections are applied it compensates possible negative effects of the type of bias correction or 2-dimensional orientations against 3-dimensional handling.

14 CFR 77.13 - Construction or alteration requiring notice.

Code of Federal Regulations, 2010 CFR

2010-01-01

... height above the ground level at its site. (2) Any construction or alteration of greater height than an... feet from the nearest point of the nearest landing and takeoff area of each heliport specified in... feet above the surface level of its site; or (2) An FAA regional office advises him that submission of...

NASA Green Propulsion Technologies Pushing Aviation to New Heights

NASA Technical Reports Server (NTRS)

Free, James M.; Jennings, Francis T.; Adanich, Emery; Del Rosario, Ruben; Felder, James L.

2014-01-01

Center Director Free is providing the Keynote at the Disruptive Propulsion Conference, sponsored by Cranfield University, Cranfield, Bedfordshire, England in November. Director Free will be presenting a PowerPoint presentation titled, NASA Green Propulsion Technologies Pushing Aviation to New Heights at both the conference and a meeting at the Royal Aeronautical Society.

The influence of age, playing position, anthropometry and fitness on career attainment outcomes in rugby league.

PubMed

Till, Kevin; Cobley, Steve; Morley, David; O'hara, John; Chapman, Chris; Cooke, Carlton

2016-01-01

This study evaluated the influence of annual-age category, relative age, playing position, anthropometry and fitness on the career attainment outcomes of junior rugby league players originally selected for a talent identification and development (TID) programme. Junior rugby league players (N = 580) were grouped retrospectively according to their career attainment level (i.e., amateur, academy and professional). Anthropometric (height, sitting height, body mass, sum of four skinfolds), maturational (age at peak height velocity; PHV) and fitness (power, speed, change of direction speed, estimated[Formula: see text]) characteristics were assessed at the Under 13s, 14s and 15s annual-age categories. Relative age (Q2 = 8.5% vs. Q4 = 25.5%) and playing position (Pivots = 19.5% vs. Props = 5.8%) influenced the percentage of players attaining professional status. Anthropometry and fitness had a significant effect on career attainment at the Under 14 (P = 0.002, η(2) = 0.16) and 15 (P = 0.01, η(2) = 0.12) annual-age categories. Findings at the Under 14s showed future professional players were significantly later maturing compared to academy and amateur players. Findings suggest that relative age, playing position, anthropometry and fitness can influence the career attainment of junior rugby league players. TID programmes within rugby league, and other related team sports, should be aware and acknowledge the factors influencing long-term career attainment, and not delimit development opportunities during early adolescence.

Water consumption and biomass production of protoplast fusion lines of poplar hybrids under drought stress

PubMed Central

Hennig, Anne; Kleinschmit, Jörg R. G.; Schoneberg, Sebastian; Löffler, Sonja; Janßen, Alwin; Polle, Andrea

2015-01-01

Woody crops such as poplars (Populus) can contribute to meet the increasing energy demand of a growing human population and can therefore enhance the security of energy supply. Using energy from biomass increases ecological sustainability as biomass is considered to play a pivotal role in abating climate change. Because areas for establishing poplar plantations are often confined to marginal sites drought tolerance is one important trait for poplar genotypes cultivated in short rotation coppice. We tested 9-month-old plants of four tetraploid Populus tremula (L.) × P. tremuloides (Michx.) lines that were generated by protoplast fusion and their diploid counterpart for water consumption and drought stress responses in a greenhouse experiment. The fusion lines showed equivalent or decreased height growth, stem biomass and total leaf area compared to the diploid line. The relative height increment of the fusion lines was not reduced compared to the diploid line when the plants were exposed to drought. The fusion lines were distinguished from the diploid counterpart by stomatal characteristics such as increased size and lower density. The changes in the stomatal apparatus did not affect the stomatal conductance. When exposed to drought the carbohydrate concentrations increased more strongly in the fusion lines than in the diploid line. Two fusion lines consumed significantly less water with regard to height growth, producing equivalent or increased relative stem biomass under drought compared to their diploid relative. Therefore, these tetraploid fusion lines are interesting candidates for short rotation biomass plantation on dry sites. PMID:26042130

a Matlab Geodetic Software for Processing Airborne LIDAR Bathymetry Data

NASA Astrophysics Data System (ADS)

Pepe, M.; Prezioso, G.

2015-04-01

The ability to build three-dimensional models through technologies based on satellite navigation systems GNSS and the continuous development of new sensors, as Airborne Laser Scanning Hydrography (ALH), data acquisition methods and 3D multi-resolution representations, have contributed significantly to the digital 3D documentation, mapping, preservation and representation of landscapes and heritage as well as to the growth of research in this fields. However, GNSS systems led to the use of the ellipsoidal height; to transform this height in orthometric is necessary to know a geoid undulation model. The latest and most accurate global geoid undulation model, available worldwide, is EGM2008 which has been publicly released by the U.S. National Geospatial-Intelligence Agency (NGA) EGM Development Team. Therefore, given the availability and accuracy of this geoid model, we can use it in geomatics applications that require the conversion of heights. Using this model, to correct the elevation of a point does not coincide with any node must interpolate elevation information of adjacent nodes. The purpose of this paper is produce a Matlab® geodetic software for processing airborne LIDAR bathymetry data. In particular we want to focus on the point clouds in ASPRS LAS format and convert the ellipsoidal height in orthometric. The algorithm, valid on the whole globe and operative for all UTM zones, allows the conversion of ellipsoidal heights using the EGM2008 model. Of this model we analyse the slopes which occur, in some critical areas, between the nodes of the undulations grid; we will focus our attention on the marine areas verifying the impact that the slopes have in the calculation of the orthometric height and, consequently, in the accuracy of the in the 3-D point clouds. This experiment will be carried out by analysing a LAS APRS file containing topographic and bathymetric data collected with LIDAR systems along the coasts of Oregon and Washington (USA).

Surface Features Parameterization and Equivalent Roughness Height Estimation of a Real Subglacial Conduit in the Arctic

NASA Astrophysics Data System (ADS)

Chen, Y.; Liu, X.; Mankoff, K. D.; Gulley, J. D.

2016-12-01

The surfaces of subglacial conduits are very complex, coupling multi-scale roughness, large sinuosity, and cross-sectional variations together. Those features significantly affect the friction law and drainage efficiency inside the conduit by altering velocity and pressure distributions, thus posing considerable influences on the dynamic development of the conduit. Parameterizing the above surface features is a first step towards understanding their hydraulic influences. A Matlab package is developed to extract the roughness field, the conduit centerline, and associated area and curvature data from the conduit surface, acquired from 3D scanning. By using those data, the characteristic vertical and horizontal roughness scales are then estimated based on the structure functions. The centerline sinuosities, defined through three concepts, i.e., the traditional definition of a fluvial river, entropy-based sinuosity, and curvature-based sinuosity, are also calculated and compared. The cross-sectional area and equivalent circular diameter along the centerline are also calculated. Among those features, the roughness is especially important due to its pivotal role in determining the wall friction, and thus an estimation of the equivalent roughness height is of great importance. To achieve such a goal, the original conduit is firstly simplified into a straight smooth pipe with the same volume and centerline length, and the roughness field obtained above is then reconstructed into the simplified pipe. An OpenFOAM-based Large-eddy-simulation (LES) is then performed based on the reconstructed pipe. Considering that the Reynolds number is of the order 106, and the relative roughness is larger than 5% for 60% of the conduit, we test the validity of the resistance law for completely rough pipe. The friction factor is calculated based on the pressure drop and mean velocity in the simulation. Working together, the equivalent roughness height can be calculated. However, whether the assumption is applicable for the current case, i.e., high relative roughness, is a question. Two other roughness heights, i.e., the vertical roughness scale based on structure functions and viscous sublayer thickness determined from the wall boundary layer are also calculated and compared with the equivalent roughness height.

A Scalable and Dynamic Testbed for Conducting Penetration-Test Training in a Laboratory Environment

DTIC Science & Technology

2015-03-01

entry point through which to execute a payload to accomplish a higher-level goal: executing arbitrary code, escalating privileges , pivoting...Mobile Ad Hoc Network Emulator (EMANE)26 can emulate the entire network stack (physical to application -layer protocols). 2. Methodology To build a...to host Windows, Linux, MacOS, Android , and other operating systems without much effort. 4 E. A simple and automatic “restore” function: Many

"Shut the F*** up", "You Have No Rights Here": Critical Race Theory and Racialisation in Post-7/7 Racist Britain

ERIC Educational Resources Information Center

Cole, Mike; Maisuria, Alpesh

2007-01-01

The London bombings of 7th July, 2007 (7/7) were a pivotal moment in British society, not only because of the loss of life and injury, but because it was the first time Britain had been attacked by non-white British citizens. This point was underscored by Chancellor Gordon Brown when he stressed that "the uncomfortable facts" have to be…

Pivots of Operations: Implications for Operational Sustainment Design

DTIC Science & Technology

1991-05-21

wealthier towns; linked by wide, major roads and navigable rivers with bridg - es as points of passage; and secured by fortresses. 39 These considerations...on the first of June. This precious acquisition secured to us three fine bridges across the Adige; and the bastioned work, and two strong castles...1812, Napoleon had re- treated from his campaign in Russia to Germany . Prussia, Sweden, and Austria mobilized to join the Russians against him.43

Exterior building details of Building A; west façade: white painted ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Exterior building details of Building A; west façade: white painted brick wall of road and second level, road level: paired four-light casement window and a small single-light wood casement window; second level: four-over-four wood double-hung window and a six-light horizontal pivot over a three-light fixed window; easterly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

A new Ellipsoidal Gravimetric-Satellite Altimetry Boundary Value Problem; Case study: High Resolution Geoid of Iran

NASA Astrophysics Data System (ADS)

Ardalan, A.; Safari, A.; Grafarend, E.

2003-04-01

A new ellipsoidal gravimetric-satellite altimetry boundary value problem has been developed and successfully tested. This boundary value problem has been constructed for gravity observables of the type (i) gravity potential (ii) gravity intensity (iii) deflection of vertical and (iv) satellite altimetry data. The developed boundary value problem is enjoying the ellipsoidal nature and as such can take advantage of high precision GPS observations in the set-up of the problem. The highlights of the solution are as follows: begin{itemize} Application of ellipsoidal harmonic expansion up to degree/order and ellipsoidal centrifugal field for the reduction of global gravity and isostasy effects from the gravity observable at the surface of the Earth. Application of ellipsoidal Newton integral on the equal area map projection surface for the reduction of residual mass effects within a radius of 55 km around the computational point. Ellipsoidal harmonic downward continuation of the residual observables from the surface of the earth down to the surface of reference ellipsoid using the ellipsoidal height of the observation points derived from GPS. Restore of the removed effects at the application points on the surface of reference ellipsoid. Conversion of the satellite altimetry derived heights of the water bodies into potential. Combination of the downward continued gravity information with the potential equivalent of the satellite altimetry derived heights of the water bodies. Application of ellipsoidal Bruns formula for converting the potential values on the surface of the reference ellipsoid into the geoidal heights (i.e. ellipsoidal heights of the geoid) with respect to the reference ellipsoid. Computation of the high-resolution geoid of Iran has successfully tested this new methodology!

Grinding arrangement for ball nose milling cutters

NASA Technical Reports Server (NTRS)

Burch, C. F. (Inventor)

1974-01-01

A grinding arrangement for spiral fluted ball nose end mills and like tools includes a tool holder for positioning the tool relative to a grinding wheel. The tool is mounted in a spindle within the tool holder for rotation about its centerline and the tool holder is pivotably mounted for angular movement about an axis which intersects that centerline. A follower arm of a cam follower secured to the spindle cooperates with a specially shaped cam to provide rotation of the tool during the angular movement of the tool holder during the grinding cycle, by an amount determined by the cam profile. In this way the surface of the cutting edge in contact with the grinding wheel is maintained at the same height on the grinding wheel throughout the angular movement of the tool holder during the grinding cycle.

Hands-Free Transcranial Color Doppler Probe

NASA Technical Reports Server (NTRS)

Chin, Robert; Madala, Srihdar; Sattler, Graham

2012-01-01

Current transcranial color Doppler (TCD) transducer probes are bulky and difficult to move in tiny increments to search and optimize TCD signals. This invention provides miniature motions of a TCD transducer probe to optimize TCD signals. The mechanical probe uses spherical bearing in guiding and locating the tilting crystal face. The lateral motion of the crystal face as it tilts across the full range of motion was achieved by minimizing the distance between the pivot location and the crystal face. The smallest commonly available metal spherical bearing was used with an outer diameter of 12 mm, a 3-mm tall retaining ring, and 5-mm overall height. Small geared motors were used that would provide sufficient power in a very compact package. After confirming the validity of the basic positioning concept, optimization design loops were completed to yield the final design.

Anthropometric, physiological and performance characteristics of elite team-handball players.

PubMed

Chaouachi, Anis; Brughelli, Matt; Levin, Gregory; Boudhina, Nahla Ben Brahim; Cronin, John; Chamari, Karim

2009-01-15

The objective of this study was to provide anthropometric, physiological, and performance characteristics of an elite international handball team. Twenty-one elite handball players were tested and categorized according to their playing positions (goalkeepers, backs, pivots, and wings). Testing consisted of anthropometric and physiological measures of height, body mass, percentage body fat and endurance (VO(2max)), performance measures of speed (5, 10, and 30 m), strength (bench press and squat), unilateral and bilateral horizontal jumping ability, and a 5-jump horizontal test. Significant differences were found between player positions for some anthropometric characteristics (height and percentage body fat) but not for the physiological or performance characteristics. Strong correlations were noted between single leg horizontal jumping distances with 5-, 10-, and 30-m sprint times (r = 0.51-0.80; P < 0.01). The best predictors of sprint times were single leg horizontal jumping with the dominant leg and the distance measured for the 5-jump test, which when combined accounted for 72% of the common variance associated with sprint ability. In conclusion, performance abilities between positions in elite team-handball players appear to be very similar. Single leg horizontal jumping distance could be a specific standardized test for predicting sprinting ability in elite handball players.

Soft computing methods for geoidal height transformation

NASA Astrophysics Data System (ADS)

Akyilmaz, O.; Özlüdemir, M. T.; Ayan, T.; Çelik, R. N.

2009-07-01

Soft computing techniques, such as fuzzy logic and artificial neural network (ANN) approaches, have enabled researchers to create precise models for use in many scientific and engineering applications. Applications that can be employed in geodetic studies include the estimation of earth rotation parameters and the determination of mean sea level changes. Another important field of geodesy in which these computing techniques can be applied is geoidal height transformation. We report here our use of a conventional polynomial model, the Adaptive Network-based Fuzzy (or in some publications, Adaptive Neuro-Fuzzy) Inference System (ANFIS), an ANN and a modified ANN approach to approximate geoid heights. These approximation models have been tested on a number of test points. The results obtained through the transformation processes from ellipsoidal heights into local levelling heights have also been compared.

The optimum spanning catenary cable

NASA Astrophysics Data System (ADS)

Wang, C. Y.

2015-03-01

A heavy cable spans two points in space. There exists an optimum cable length such that the maximum tension is minimized. If the two end points are at the same level, the optimum length is 1.258 times the distance between the ends. The optimum lengths for end points of different heights are also found.

a New Mask for Automatic Building Detection from High Density Point Cloud Data and Multispectral Imagery

NASA Astrophysics Data System (ADS)

Awrangjeb, M.; Siddiqui, F. U.

2017-11-01

In complex urban and residential areas, there are buildings which are not only connected with and/or close to one another but also partially occluded by their surrounding vegetation. Moreover, there may be buildings whose roofs are made of transparent materials. In transparent buildings, there are point returns from both the ground (or materials inside the buildings) and the rooftop. These issues confuse the previously proposed building masks which are generated from either ground points or non-ground points. The normalised digital surface model (nDSM) is generated from the non-ground points and usually it is hard to find individual buildings and trees using the nDSM. In contrast, the primary building mask is produced using the ground points, thereby it misses the transparent rooftops. This paper proposes a new building mask based on the non-ground points. The dominant directions of non-ground lines extracted from the multispectral imagery are estimated. A dummy grid with the target mask resolution is rotated at each dominant direction to obtain the corresponding height values from the non-ground points. Three sub-masks are then generated from the height grid by estimating the gradient function. Two of these sub-masks capture planar surfaces whose height remain constant in along and across the dominant direction, respectively. The third sub-mask contains only the flat surfaces where the height (ideally) remains constant in all directions. All the sub-masks generated in all estimated dominant directions are combined to produce the candidate building mask. Although the application of the gradient function helps in removal of most of the vegetation, the final building mask is obtained through removal of planar vegetation, if any, and tiny isolated false candidates. Experimental results on three Australian data sets show that the proposed method can successfully remove vegetation, thereby separate buildings from occluding vegetation and detect buildings with transparent roof materials. While compared to existing building detection techniques, the proposed technique offers higher objectbased completeness, correctness and quality, specially in complex scenes with aforementioned issues. It is not only capable of detecting transparent buildings, but also small garden sheds which are sometimes as small as 5 m2 in area.

Universal adsorption at the vapor-liquid interface near the consolute point

NASA Technical Reports Server (NTRS)

Schmidt, James W.

1990-01-01

The ellipticity of the vapor-liquid interface above mixtures of methylcyclohexane (C7H14) and perfluoromethylcyclohexane (C7F14) has been measured near the consolute point T(c) = 318.6 K. The data are consistent with a model of the interface that combines a short-ranged density-vs height profile in the vapor phase with a much longer-ranged composition-versus-height profile in the liquid. The value of the free parameter produced by fitting the model to the data is consistent with results from two other simple mixtures and a mixture of a polymer and solvent. This experiment combines precision ellipsometry of the vapor-liquid interface with in situ measurements of refractive indices of the liquid phases, and it precisely locates the consolute point.

14 CFR 77.13 - Construction or alteration requiring notice.

Code of Federal Regulations, 2011 CFR

2011-01-01

... feet in height above the ground level at its site. (2) Any construction or alteration of greater height... 5,000 feet from the nearest point of the nearest landing and takeoff area of each heliport specified... construction or alteration is more than 200 feet above the surface level of its site; or (2) An FAA regional...

Geolocation error tracking of ZY-3 three line cameras

NASA Astrophysics Data System (ADS)

Pan, Hongbo

2017-01-01

The high-accuracy geolocation of high-resolution satellite images (HRSIs) is a key issue for mapping and integrating multi-temporal, multi-sensor images. In this manuscript, we propose a new geometric frame for analysing the geometric error of a stereo HRSI, in which the geolocation error can be divided into three parts: the epipolar direction, cross base direction, and height direction. With this frame, we proved that the height error of three line cameras (TLCs) is independent of nadir images, and that the terrain effect has a limited impact on the geolocation errors. For ZY-3 error sources, the drift error in both the pitch and roll angle and its influence on the geolocation accuracy are analysed. Epipolar and common tie-point constraints are proposed to study the bundle adjustment of HRSIs. Epipolar constraints explain that the relative orientation can reduce the number of compensation parameters in the cross base direction and have a limited impact on the height accuracy. The common tie points adjust the pitch-angle errors to be consistent with each other for TLCs. Therefore, free-net bundle adjustment of a single strip cannot significantly improve the geolocation accuracy. Furthermore, the epipolar and common tie-point constraints cause the error to propagate into the adjacent strip when multiple strips are involved in the bundle adjustment, which results in the same attitude uncertainty throughout the whole block. Two adjacent strips-Orbit 305 and Orbit 381, covering 7 and 12 standard scenes separately-and 308 ground control points (GCPs) were used for the experiments. The experiments validate the aforementioned theory. The planimetric and height root mean square errors were 2.09 and 1.28 m, respectively, when two GCPs were settled at the beginning and end of the block.

Height, education and later-life cognition in Latin America and the Caribbean.

PubMed

Maurer, Jürgen

2010-07-01

Building on previous evidence from the U.S., this study investigates the relationship between anthropometric markers (height and knee height), early-life conditions, education, and cognitive function in later life among urban elderly from Latin America and the Caribbean. I document a positive association between height and later-life cognitive function, which is larger for women than for men. This sex difference increases when I address potential feedback effects from mid- and later-life circumstances on stature by using knee height as an instrument for height. Specifically, while the estimates for women remain largely unchanged, I only find a diminished and statistically insignificant association between instrumented height and later-life cognition for men. This finding suggests that at least part of the association between height and later-life cognition among men may stem from common third factors that are correlated with both height and later-life cognition, such as adverse occupational exposures or health events during mid- and later life. Extended models that also include education further diminish the association between height and later-life cognition. Education displays strong positive gradients with the employed measures of childhood circumstances - including height - which points to education as a potential pathway linking early-life conditions and later-life cognitive function. 2010 Elsevier B.V. All rights reserved.

Automated lidar-derived canopy height estimates for the Upper Mississippi River System

USGS Publications Warehouse

Hlavacek, Enrika

2015-01-01

Land cover/land use (LCU) classifications serve as important decision support products for researchers and land managers. The LCU classifications produced by the U.S. Geological Survey’s Upper Midwest Environmental Sciences Center (UMESC) include canopy height estimates that are assigned through manual aerial photography interpretation techniques. In an effort to improve upon these techniques, this project investigated the use of high-density lidar data for the Upper Mississippi River System to determine canopy height. An ArcGIS tool was developed to automatically derive height modifier information based on the extent of land cover features for forest classes. The measurement of canopy height included a calculation of the average height from lidar point cloud data as well as the inclusion of a local maximum filter to identify individual tree canopies. Results were compared to original manually interpreted height modifiers and to field survey data from U.S. Forest Service Forest Inventory and Analysis plots. This project demonstrated the effectiveness of utilizing lidar data to more efficiently assign height modifier attributes to LCU classifications produced by the UMESC.

Method and system for dual resolution translation stage

DOEpatents

Halpin, John Michael

2014-04-22

A dual resolution translation stage includes a stage assembly operable to receive an optical element and a low resolution adjustment device mechanically coupled to the stage assembly. The dual resolution stage also includes an adjustable pivot block mechanically coupled to the stage assembly. The adjustable pivot block includes a pivot shaft. The dual resolution stage further includes a lever arm mechanically coupled to the adjustable pivot block. The lever arm is operable to pivot about the pivot shaft. The dual resolution stage additionally includes a high resolution adjustment device mechanically coupled to the lever arm and the stage assembly.

SCRIBE (Stratospheric Cryogenic Interferometer Baloon Experiment) Data Survey and Validation.

DTIC Science & Technology

1987-02-16

Altitude of 27000 to 28000 m, SPIE Publ. 366, p165-172, AD-A133 472. 5 ferometer 3 𔃾 𔃿 and to point out flaws in the system which were subsequently...Tangent Height - 16.9 km * 6 j4 II’ a. WA#EUM k CM p Altitude = 31.3 km ’ / Zenith Angle = 93.7 deg.- ouTangent Height = 16.9 km I- + p ISO . .. .. 0...Height = 30.47 106 250 200 ISO ........................., .................................. ’ 65S 660 665 670 675 WAVENUMBER (CM-1) Figure 31. Comparison

The quadrant method measuring four points is as a reliable and accurate as the quadrant method in the evaluation after anatomical double-bundle ACL reconstruction.

PubMed

Mochizuki, Yuta; Kaneko, Takao; Kawahara, Keisuke; Toyoda, Shinya; Kono, Norihiko; Hada, Masaru; Ikegami, Hiroyasu; Musha, Yoshiro

2017-11-20

The quadrant method was described by Bernard et al. and it has been widely used for postoperative evaluation of anterior cruciate ligament (ACL) reconstruction. The purpose of this research is to further develop the quadrant method measuring four points, which we named four-point quadrant method, and to compare with the quadrant method. Three-dimensional computed tomography (3D-CT) analyses were performed in 25 patients who underwent double-bundle ACL reconstruction using the outside-in technique. The four points in this study's quadrant method were defined as point1-highest, point2-deepest, point3-lowest, and point4-shallowest, in femoral tunnel position. Value of depth and height in each point was measured. Antero-medial (AM) tunnel is (depth1, height2) and postero-lateral (PL) tunnel is (depth3, height4) in this four-point quadrant method. The 3D-CT images were evaluated independently by 2 orthopaedic surgeons. A second measurement was performed by both observers after a 4-week interval. Intra- and inter-observer reliability was calculated by means of intra-class correlation coefficient (ICC). Also, the accuracy of the method was evaluated against the quadrant method. Intra-observer reliability was almost perfect for both AM and PL tunnel (ICC > 0.81). Inter-observer reliability of AM tunnel was substantial (ICC > 0.61) and that of PL tunnel was almost perfect (ICC > 0.81). The AM tunnel position was 0.13% deep, 0.58% high and PL tunnel position was 0.01% shallow, 0.13% low compared to quadrant method. The four-point quadrant method was found to have high intra- and inter-observer reliability and accuracy. This method can evaluate the tunnel position regardless of the shape and morphology of the bone tunnel aperture for use of comparison and can provide measurement that can be compared with various reconstruction methods. The four-point quadrant method of this study is considered to have clinical relevance in that it is a detailed and accurate tool for evaluating femoral tunnel position after ACL reconstruction. Case series, Level IV.

Piezo activated mode tracking system for widely tunable mode-hop-free external cavity mid-IR semiconductor lasers

NASA Technical Reports Server (NTRS)

Tittel, Frank K. (Inventor); Curl, Robert F. (Inventor); Wysocki, Gerard (Inventor)

2010-01-01

A widely tunable, mode-hop-free semiconductor laser operating in the mid-IR comprises a QCL laser chip having an effective QCL cavity length, a diffraction grating defining a grating angle and an external cavity length with respect to said chip, and means for controlling the QCL cavity length, the external cavity length, and the grating angle. The laser of claim 1 wherein said chip may be tuned over a range of frequencies even in the absence of an anti-reflective coating. The diffraction grating is controllably pivotable and translatable relative to said chip and the effective QCL cavity length can be adjusted by varying the injection current to the chip. The laser can be used for high resolution spectroscopic applications and multi species trace-gas detection. Mode-hopping is avoided by controlling the effective QCL cavity length, the external cavity length, and the grating angle so as to replicate a virtual pivot point.

Validation Study on Alos Prism Dsm Mosaic and Aster Gdem 2

NASA Astrophysics Data System (ADS)

Tadono, T.; Takaku, J.; Shimada, M.

2012-07-01

This study aims to evaluate height accuracy of two datasets obtained by spaceborne optical instruments of a digital elevation data for a large-scale area. The digital surface model (DSM) was generated by the Panchromatic Remote-sensing Instrument for Stereo Mapping (PRISM) onboard the Advanced Land Observing Satellite (ALOS, nicknamed 'Daichi'), and the global digital elevation model (DEM) version 2 (GDEM-2) was derived from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) onboard NASA's TERRA satellite. The test site of this study was the entire country of Bhutan, which is located on the southern slopes of the eastern Himalayas. Bhutan is not a large country, covering about 330 km from east to west, and 170 km from north to south; however, it has large height variation from 200 m to more than 7,000 m. This therefore makes it very interesting for validating digital topographic information in terms of national scale generation as well as wide height range. Regarding the reference data, field surveys were conducted in 2010 and 2011, and collected ground control points by a global positioning system were used for evaluating precise height accuracies in point scale as check points (CPs), with a 3 arc-sec DEM created by the Shuttle Radar Topography Mission (SRTM-3) used to validate the wide region. The results confirmed a root mean square error of 8.1 m for PRISM DSM and 29.4 m for GDEM-2 by CPs.

What does it take to have a high-grade pivot shift?

PubMed

Tanaka, M; Vyas, D; Moloney, G; Bedi, A; Pearle, A D; Musahl, V

2012-04-01

The pivot shift is the most specific clinical test to assess pathological knee joint rotatory laxity following ACL injury. This article attempts to describe the anatomic structures responsible for creating a high-grade pivot shift and their potential role in customizing ACL reconstruction. A review of the literature demonstrates that disruption of the secondary stabilizers of anterior translation of the lateral compartment including the lateral meniscus, anterolateral capsule, and IT band contributes to a high-grade pivot shift in the ACL-deficient knee. The morphology of the lateral tibial plateau, including increased posteroinferior tibial slope and small size, can also contribute to high-grade pivot shift. Factors that may decrease the grade of the pivot shift include medial compartment injury, MCL injury, patient guarding, and osteoarthritis. In conclusion, a high-grade pivot shift in the ACL-deficient knee is often associated with incompetence of the lateral soft tissue envelope. Rotatory laxity as assessed by the pivot shift may also be falsely underestimated by concomitant injuries. IV.

First Prismatic Building Model Reconstruction from Tomosar Point Clouds

NASA Astrophysics Data System (ADS)

Sun, Y.; Shahzad, M.; Zhu, X.

2016-06-01

This paper demonstrates for the first time the potential of explicitly modelling the individual roof surfaces to reconstruct 3-D prismatic building models using spaceborne tomographic synthetic aperture radar (TomoSAR) point clouds. The proposed approach is modular and works as follows: it first extracts the buildings via DSM generation and cutting-off the ground terrain. The DSM is smoothed using BM3D denoising method proposed in (Dabov et al., 2007) and a gradient map of the smoothed DSM is generated based on height jumps. Watershed segmentation is then adopted to oversegment the DSM into different regions. Subsequently, height and polygon complexity constrained merging is employed to refine (i.e., to reduce) the retrieved number of roof segments. Coarse outline of each roof segment is then reconstructed and later refined using quadtree based regularization plus zig-zag line simplification scheme. Finally, height is associated to each refined roof segment to obtain the 3-D prismatic model of the building. The proposed approach is illustrated and validated over a large building (convention center) in the city of Las Vegas using TomoSAR point clouds generated from a stack of 25 images using Tomo-GENESIS software developed at DLR.

Discounting the value of safety: effects of perceived risk and effort.

PubMed

Sigurdsson, Sigurdur O; Taylor, Matthew A; Wirth, Oliver

2013-09-01

Although falls from heights remain the most prevalent cause of fatalities in the construction industry, factors impacting safety-related choices associated with work at heights are not completely understood. Better tools are needed to identify and study the factors influencing safety-related choices and decision making. Using a computer-based task within a behavioral economics paradigm, college students were presented a choice between two hypothetical scenarios that differed in working height and effort associated with retrieving and donning a safety harness. Participants were instructed to choose the scenario in which they were more likely to wear the safety harness. Based on choice patterns, switch points were identified, indicating when the perceived risk in both scenarios was equivalent. Switch points were a systematic function of working height and effort, and the quantified relation between perceived risk and effort was described well by a hyperbolic equation. Choice patterns revealed that the perceived risk of working at heights decreased as the effort to retrieve and don a safety harness increased. Results contribute to the development of computer-based procedure for assessing risk discounting within a behavioral economics framework. Such a procedure can be used as a research tool to study factors that influence safety-related decision making with a goal of informing more effective prevention and intervention strategies. Copyright © 2013 National Safety Council and Elsevier Ltd. All rights reserved.

Use of three-point taper systems in timber cruising

Treesearch

James W. Flewelling; Richard L. Ernst; Lawrence M. Raynes

2000-01-01

Tree volumes and profiles are often estimated as functions of total height and DBH. Alternative estimators include form-class methods, importance sampling, the centroid method, and multi-point profile (taper) estimation systems; all of these require some measurement or estimate of upper stem diameters. The multi-point profile system discussed here allows for upper stem...

Development and Present Situation Analysis of Power Transformer State Maintenance

NASA Astrophysics Data System (ADS)

Lv, Sen; Li, Biao; Li, Huan

2018-02-01

The pivotal status of power transformer in the power system is one of the most important equipment. The safety and reliability of its operation is directly related to the safety and stability of power system. Based on the analysis of the present situation of power transformer state maintenance in home and abroad. The paper points out the deficiency of the current method and provides a theoretical basis for further research, which has a certain guiding significance.

Implied dynamics biases the visual perception of velocity.

PubMed

La Scaleia, Barbara; Zago, Myrka; Moscatelli, Alessandro; Lacquaniti, Francesco; Viviani, Paolo

2014-01-01

We expand the anecdotic report by Johansson that back-and-forth linear harmonic motions appear uniform. Six experiments explore the role of shape and spatial orientation of the trajectory of a point-light target in the perceptual judgment of uniform motion. In Experiment 1, the target oscillated back-and-forth along a circular arc around an invisible pivot. The imaginary segment from the pivot to the midpoint of the trajectory could be oriented vertically downward (consistent with an upright pendulum), horizontally leftward, or vertically upward (upside-down). In Experiments 2 to 5, the target moved uni-directionally. The effect of suppressing the alternation of movement directions was tested with curvilinear (Experiment 2 and 3) or rectilinear (Experiment 4 and 5) paths. Experiment 6 replicated the upright condition of Experiment 1, but participants were asked to hold the gaze on a fixation point. When some features of the trajectory evoked the motion of either a simple pendulum or a mass-spring system, observers identified as uniform the kinematic profiles close to harmonic motion. The bias towards harmonic motion was most consistent in the upright orientation of Experiment 1 and 6. The bias disappeared when the stimuli were incompatible with both pendulum and mass-spring models (Experiments 3 to 5). The results are compatible with the hypothesis that the perception of dynamic stimuli is biased by the laws of motion obeyed by natural events, so that only natural motions appear uniform.

49 CFR 393.132 - What are the rules for securing flattened or crushed vehicles?

Code of Federal Regulations, 2011 CFR

2011-10-01

... is prohibited except that such webbing may be used to connect wire rope or chain to anchor points on... or comparable means on four sides which extend to the full height of the load and which block against... comparable means on three sides which extend to the full height of the load and which block against movement...

49 CFR 393.132 - What are the rules for securing flattened or crushed vehicles?

Code of Federal Regulations, 2010 CFR

2010-10-01

... is prohibited except that such webbing may be used to connect wire rope or chain to anchor points on... or comparable means on four sides which extend to the full height of the load and which block against... comparable means on three sides which extend to the full height of the load and which block against movement...

49 CFR 393.132 - What are the rules for securing flattened or crushed vehicles?

Code of Federal Regulations, 2012 CFR

2012-10-01

... is prohibited except that such webbing may be used to connect wire rope or chain to anchor points on... or comparable means on four sides which extend to the full height of the load and which block against... comparable means on three sides which extend to the full height of the load and which block against movement...

49 CFR 393.132 - What are the rules for securing flattened or crushed vehicles?

Code of Federal Regulations, 2014 CFR

2014-10-01

... is prohibited except that such webbing may be used to connect wire rope or chain to anchor points on... or comparable means on four sides which extend to the full height of the load and which block against... comparable means on three sides which extend to the full height of the load and which block against movement...

49 CFR 393.132 - What are the rules for securing flattened or crushed vehicles?

Code of Federal Regulations, 2013 CFR

2013-10-01

... is prohibited except that such webbing may be used to connect wire rope or chain to anchor points on... or comparable means on four sides which extend to the full height of the load and which block against... comparable means on three sides which extend to the full height of the load and which block against movement...

Predicting vertical jump height from bar velocity.

PubMed

García-Ramos, Amador; Štirn, Igor; Padial, Paulino; Argüelles-Cienfuegos, Javier; De la Fuente, Blanca; Strojnik, Vojko; Feriche, Belén

2015-06-01

The objective of the study was to assess the use of maximum (Vmax) and final propulsive phase (FPV) bar velocity to predict jump height in the weighted jump squat. FPV was defined as the velocity reached just before bar acceleration was lower than gravity (-9.81 m·s(-2)). Vertical jump height was calculated from the take-off velocity (Vtake-off) provided by a force platform. Thirty swimmers belonging to the National Slovenian swimming team performed a jump squat incremental loading test, lifting 25%, 50%, 75% and 100% of body weight in a Smith machine. Jump performance was simultaneously monitored using an AMTI portable force platform and a linear velocity transducer attached to the barbell. Simple linear regression was used to estimate jump height from the Vmax and FPV recorded by the linear velocity transducer. Vmax (y = 16.577x - 16.384) was able to explain 93% of jump height variance with a standard error of the estimate of 1.47 cm. FPV (y = 12.828x - 6.504) was able to explain 91% of jump height variance with a standard error of the estimate of 1.66 cm. Despite that both variables resulted to be good predictors, heteroscedasticity in the differences between FPV and Vtake-off was observed (r(2) = 0.307), while the differences between Vmax and Vtake-off were homogenously distributed (r(2) = 0.071). These results suggest that Vmax is a valid tool for estimating vertical jump height in a loaded jump squat test performed in a Smith machine. Key pointsVertical jump height in the loaded jump squat can be estimated with acceptable precision from the maximum bar velocity recorded by a linear velocity transducer.The relationship between the point at which bar acceleration is less than -9.81 m·s(-2) and the real take-off is affected by the velocity of movement.Mean propulsive velocity recorded by a linear velocity transducer does not appear to be optimal to monitor ballistic exercise performance.

Predicting Vertical Jump Height from Bar Velocity

PubMed Central

García-Ramos, Amador; Štirn, Igor; Padial, Paulino; Argüelles-Cienfuegos, Javier; De la Fuente, Blanca; Strojnik, Vojko; Feriche, Belén

2015-01-01

The objective of the study was to assess the use of maximum (Vmax) and final propulsive phase (FPV) bar velocity to predict jump height in the weighted jump squat. FPV was defined as the velocity reached just before bar acceleration was lower than gravity (-9.81 m·s-2). Vertical jump height was calculated from the take-off velocity (Vtake-off) provided by a force platform. Thirty swimmers belonging to the National Slovenian swimming team performed a jump squat incremental loading test, lifting 25%, 50%, 75% and 100% of body weight in a Smith machine. Jump performance was simultaneously monitored using an AMTI portable force platform and a linear velocity transducer attached to the barbell. Simple linear regression was used to estimate jump height from the Vmax and FPV recorded by the linear velocity transducer. Vmax (y = 16.577x - 16.384) was able to explain 93% of jump height variance with a standard error of the estimate of 1.47 cm. FPV (y = 12.828x - 6.504) was able to explain 91% of jump height variance with a standard error of the estimate of 1.66 cm. Despite that both variables resulted to be good predictors, heteroscedasticity in the differences between FPV and Vtake-off was observed (r2 = 0.307), while the differences between Vmax and Vtake-off were homogenously distributed (r2 = 0.071). These results suggest that Vmax is a valid tool for estimating vertical jump height in a loaded jump squat test performed in a Smith machine. Key points Vertical jump height in the loaded jump squat can be estimated with acceptable precision from the maximum bar velocity recorded by a linear velocity transducer. The relationship between the point at which bar acceleration is less than -9.81 m·s-2 and the real take-off is affected by the velocity of movement. Mean propulsive velocity recorded by a linear velocity transducer does not appear to be optimal to monitor ballistic exercise performance. PMID:25983572

Developing a bivariate spatial association measure: An integration of Pearson's r and Moran's I

NASA Astrophysics Data System (ADS)

Lee, Sang-Il

This research is concerned with developing a bivariate spatial association measure or spatial correlation coefficient, which is intended to capture spatial association among observations in terms of their point-to-point relationships across two spatial patterns. The need for parameterization of the bivariate spatial dependence is precipitated by the realization that aspatial bivariate association measures, such as Pearson's correlation coefficient, do not recognize spatial distributional aspects of data sets. This study devises an L statistic by integrating Pearson's r as an aspatial bivariate association measure and Moran's I as a univariate spatial association measure. The concept of a spatial smoothing scalar (SSS) plays a pivotal role in this task.

Foot roll-over evaluation based on 3D dynamic foot scan.

PubMed

Samson, William; Van Hamme, Angèle; Sanchez, Stéphane; Chèze, Laurence; Van Sint Jan, Serge; Feipel, Véronique

2014-01-01

Foot roll-over is commonly analyzed to evaluate gait pathologies. The current study utilized a dynamic foot scanner (DFS) to analyze foot roll-over. The right feet of ten healthy subjects were assessed during gait trials with a DFS system integrated into a walkway. A foot sole picture was computed by vertically projecting points from the 3D foot shape which were lower than a threshold height of 15 mm. A 'height' value of these projected points was determined; corresponding to the initial vertical coordinates prior to projection. Similar to pedobarographic analysis, the foot sole picture was segmented into anatomical regions of interest (ROIs) to process mean height (average of height data by ROI) and projected surface (area of the projected foot sole by ROI). Results showed that these variables evolved differently to plantar pressure data previously reported in the literature, mainly due to the specificity of each physical quantity (millimeters vs Pascals). Compared to plantar pressure data arising from surface contact by the foot, the current method takes into account the whole plantar aspect of the foot, including the parts that do not make contact with the support surface. The current approach using height data could contribute to a better understanding of specific aspects of foot motion during walking, such as plantar arch height and the windlass mechanism. Results of this study show the underlying method is reliable. Further investigation is required to validate the DFS measurements within a clinical context, prior to implementation into clinical practice. Copyright © 2013 Elsevier B.V. All rights reserved.

The Role of Astro-Geodetic in Precise Guidance of Long Tunnels

NASA Astrophysics Data System (ADS)

Mirghasempour, M.; Jafari, A. Y.

2015-12-01

One of prime aspects of surveying projects is guidance of paths of a long tunnel from different directions and finally ending all paths in a specific place. This kind of underground surveying, because of particular condition, has some different points in relation to the ground surveying, including Improper geometry in underground transverse, low precise measurement in direction and length due to condition such as refraction, distinct gravity between underground point and corresponding point on the ground (both value and direction of gravity) and etc. To solve this problems, astro-geodetic that is part of geodesy science, can help surveying engineers. In this article, the role of astronomy is defined in two subjects: 1- Azimuth determination of directions from entrance and exit nets of tunnel and also calibration of gyro-theodolite to use them in Underground transvers: By astronomical methods, azimuth of directions can be determine with an accuracy of 0.5 arcsecond, whereas, nowadays, no gyroscope can measure the azimuth in this accuracy; For instance, accuracy of the most precise gyroscope (Gyromat 5000) is 1.2 cm over a distance of one kilometre (2.4 arcsecond). Furthermore, the calibration methods that will be mention in this article, have significance effects on underground transverse. 2- Height relation between entrance point and exit point is problematic and time consuming; For example, in a 3 km long tunnel ( in Arak- Khoram Abad freeway), to relate entrance point to exit point, it is necessary to perform levelling about 90 km. Other example of this boring and time consuming levelling is in Kerman tunnel. This tunnel is 36 km length, but to transfer the entrance point height to exit point, 150 km levelling is needed. According to this paper, The solution for this difficulty is application of astro-geodetic and determination of vertical deflection by digital zenith camera system TZK2-D. These two elements make possible to define geoid profile in terms of tunnel azimuth in entrance and exit of tunnel; So by doing this, surveying engineers are able to transfer entrance point height to exit point of tunnels in easiest way.

Vertical Jump Height is more Strongly Associated with Velocity and Work Performed Prior to Take-off

NASA Technical Reports Server (NTRS)

Bentley, J. R.; Loehr, J. A.; DeWitt, J. K.; Lee, S. M. C.; English, K. L.; Nash, R. E.; Leach, M. A.; Hagan, R. D.

2008-01-01

Vertical jump (VJ) height is commonly used as a measure of athletic capability in strength and power sports. Although VJ has been shown to be a predictor of athletic performance, it is not clear which kinetic ground reaction force (GRF) variables, such as peak force (PF), peak power (PP), peak velocity (PV), total work (TW) or impulse (Imp) are the best correlates. To determine which kinetic variables (PF, PP, PV, TW, and Imp) best correlate with VJ height. Twenty subjects (14 males, 6 females) performed three maximal countermovement VJs on a force platform (Advanced Mechanical Technology, Inc., Watertown, MA, USA). VJ jump height was calculated as the difference between standing reach and the highest reach point measured using a Vertec. PF, PP, PV, TW, and Imp were calculated using the vertical GRF data sampled at 1000 Hz from the lowest point in the countermovement through the concentric portion until take-off. GRF data were normalized to body mass measured using a standard scale (Detecto, Webb City, MO, USA). Correlation coefficients were computed between each GRF variable and VJ height using a Pearson correlation. VJ height (43.4 plus or minus 9.1 cm) was significantly correlated (p less than 0.001) with PF (998 plus or minus 321 N; r=0.51), PP (1997 plus or minus 772 W; r=0.69), PV (2.66 plus or minus 0.40 m (raised dot) s(sup -1); r=0.85), TW (259 plus or minus 93.0 kJ; r=0.82), and Imp (204 plus or minus 51.1 N(raised dot)s; r=0.67). Although all variables were correlated to VJ height, PV and TW were more strongly correlated to VJ height than PF, PP, and Imp. Therefore, since TW is equal to force times displacement, the relative displacement of the center of mass along with the forces applied during the upward movement of the jump are critical determinants of VJ height. PV and TW are key determinants of VJ height, and therefore successful training programs to increase VJ height should focus on rapid movement (PV) and TW by increasing power over time rather than focusing on PF alone.

Monitoring urban subsidence based on SAR lnterferometric point target analysis

USGS Publications Warehouse

Zhang, Y.; Zhang, Jiahua; Gong, W.; Lu, Z.

2009-01-01

lnterferometric point target analysis (IPTA) is one of the latest developments in radar interferometric processing. It is achieved by analysis of the interferometric phases of some individual point targets, which are discrete and present temporarily stable backscattering characteristics, in long temporal series of interferometric SAR images. This paper analyzes the interferometric phase model of point targets, and then addresses two key issues within IPTA process. Firstly, a spatial searching method is proposed to unwrap the interferometric phase difference between two neighboring point targets. The height residual error and linear deformation rate of each point target can then be calculated, when a global reference point with known height correction and deformation history is chosen. Secondly, a spatial-temporal filtering scheme is proposed to further separate the atmosphere phase and nonlinear deformation phase from the residual interferometric phase. Finally, an experiment of the developed IPTA methodology is conducted over Suzhou urban area. Totally 38 ERS-1/2 SAR scenes are analyzed, and the deformation information over 3 546 point targets in the time span of 1992-2002 are generated. The IPTA-derived deformation shows very good agreement with the published result, which demonstrates that the IPTA technique can be developed into an operational tool to map the ground subsidence over urban area.

Maternal and Paternal Height and the Risk of Preeclampsia.

PubMed

Lee, Yunsung; Magnus, Per

2018-04-01

The etiology of preeclampsia is unknown. Tall women have been found to have lower incidence of preeclampsia. This points to a possible biological causal effect but may be because of socioeconomic confounding. We used paternal height as an unexposed control to examine confounding. The MoBa (Norwegian Mother and Child Cohort Study) was used to extract data on parental heights, maternal prepregnancy weight, other background factors, and pregnancy outcomes for 99 968 singleton births. Multiple logistic regression was used to estimate odds ratios for preeclampsia according to parental height. The adjusted odds ratio for preeclampsia was 0.74 (95% CI, 0.66-0.82) for women >172 cm as compared with women <164 cm. The adjusted odds ratio for preeclampsia for men >186 cm was 1.03 (95% CI, 0.93-1.15) compared with men <178 cm. The association between maternal height and preeclampsia is unlikely to be because of confounding by familial, socioeconomic factors or by fetal genes related to height. The observed association between maternal height and preeclampsia merits further investigation. © 2018 American Heart Association, Inc.

Changes in photosynthesis and leaf characteristics with tree height in five dipterocarp species in a tropical rain forest.

PubMed

Kenzo, Tanaka; Ichie, Tomoaki; Watanabe, Yoko; Yoneda, Reiji; Ninomiya, Ikuo; Koike, Takayoshi

2006-07-01

Variations in leaf photosynthetic, morphological and biochemical properties with increasing plant height from seedlings to emergent trees were investigated in five dipterocarp species in a Malaysian tropical rain forest. Canopy openness increased significantly with tree height. Photosynthetic properties, such as photosynthetic capacity at light saturation, light compensation point, maximum rate of carboxylation and maximum rate of photosynthetic electron transport, all increased significantly with tree height. Leaf morphological and biochemical traits, such as leaf mass per area, palisade layer thickness, nitrogen concentration per unit area, chlorophyll concentration per unit dry mass and chlorophyll to nitrogen ratio, also changed significantly with tree height. Leaf properties had simple and significant relationships with tree height, with few intra- and interspecies differences. Our results therefore suggest that the photosynthetic capacity of dipterocarp trees depends on tree height, and that the trees adapt to the light environment by adjusting their leaf morphological and biochemical properties. These results should aid in developing models that can accurately estimate carbon dioxide flux and biomass production in tropical rain forests.

Tallness versus shrinkage: do women shrink with age or grow taller with recent birth date?

PubMed

Davies, K M; Recker, R R; Stegman, M R; Heaney, R P

1991-10-01

This paper presents evidence that much of the high rate of age-related height loss in women reported in cross-sectional studies is actually a cohort effect rather than an aging effect. Data from a large cross-sectional study of healthy, white American women indicate that there has been a gain in peak adult height of 1.0 cm per decade for several decades from 1900 through 1965. Data from the HES, HANES I, and HANES II studies concur on this point. By contrast, data from a longitudinal study of 191 healthy white U.S. women show only a trivial rate of decline from peak adult height in the fifth and sixth decades of life. In an unselected population, some apparent height loss with age is probably due to disease processes, such as vertebral collapse. Caution is needed in using aging to interpret differences in height and in height-dependent variables, such as bone density, in cross-sectional studies.

Integrating disparate lidar data at the national scale to assess the relationships between height above ground, land cover and ecoregions

USGS Publications Warehouse

Stoker, Jason M.; Cochrane, Mark A.; Roy, David P.

2013-01-01

With the acquisition of lidar data for over 30 percent of the US, it is now possible to assess the three-dimensional distribution of features at the national scale. This paper integrates over 350 billion lidar points from 28 disparate datasets into a national-scale database and evaluates if height above ground is an important variable in the context of other nationalscale layers, such as the US Geological Survey National Land Cover Database and the US Environmental Protection Agency ecoregions maps. While the results were not homoscedastic and the available data did not allow for a complete height census in any of the classes, it does appear that where lidar data were used, there were detectable differences in heights among many of these national classification schemes. This study supports the hypothesis that there were real, detectable differences in heights in certain national-scale classification schemes, despite height not being a variable used in any of the classification routines.

Intercontinental height datum connection with GOCE and GPS-levelling data

NASA Astrophysics Data System (ADS)

Gruber, T.; Gerlach, C.; Haagmans, R.

2012-12-01

In this study an attempt is made to establish height system datum connections based upon a gravity field and steady-state ocean circulation explorer (GOCE) gravity field model and a set of global positioning system (GPS) and levelling data. The procedure applied in principle is straightforward. First local geoid heights are obtained point wise from GPS and levelling data. Then the mean of these geoid heights is computed for regions nominally referring to the same height datum. Subsequently, these local mean geoid heights are compared with a mean global geoid from GOCE for the same region. This way one can identify an offset of the local to the global geoid per region. This procedure is applied to a number of regions distributed worldwide. Results show that the vertical datum offset estimates strongly depend on the nature of the omission error, i.e. the signal not represented in the GOCE model. For a smooth gravity field the commission error of GOCE, the quality of the GPS and levelling data and the averaging control the accuracy of the vertical datum offset estimates. In case the omission error does not cancel out in the mean value computation, because of a sub-optimal point distribution or a characteristic behaviour of the omitted part of the geoid signal, one needs to estimate a correction for the omission error from other sources. For areas with dense and high quality ground observations the EGM2008 global model is a good choice to estimate the omission error correction in theses cases. Relative intercontinental height datum offsets are estimated by applying this procedure between the United State of America (USA), Australia and Germany. These are compared to historical values provided in the literature and computed with the same procedure. The results obtained in this study agree on a level of 10 cm to the historical results. The changes mainly can be attributed to the new global geoid information from GOCE, rather than to the ellipsoidal heights or the levelled heights. These historical levelling data are still in use in many countries. This conclusion is supported by other results on the validation of the GOCE models.

Change of Martian surface height associated with polar cold spots

NASA Astrophysics Data System (ADS)

Ford, P. G.; Pettengill, G. H.

2003-12-01

For the past 30 years, orbiting microwave radiometers have observed anomalously low emission temperatures during Martian polar winters. While the physical surface temperature cannot drop significantly below 148K---the point at which CO2 starts to condense---radiometric temperatures of 110K or lower at 25μ wavelength are commonly found in isolated ``cold spots'' throughout both northern and southern polar winters. These form roughly circular patches, tens to hundreds of km in diameter, and persist for no more than a few days. Three models have been proposed to account for them: (a) an atmospheric effect that accompanies CO2 snowfall; (b) fresh surface deposits of CO2 snow; or (c) a change in the properties of CO2 slab ice. Following the success of Smith et al.1 in using the MOLA laser altimeter aboard Mars Global Surveyor to directly measure the growth of the winter polar caps, we have applied the same technique to ask whether cold spots are accompanied by a sudden change in surface height. To identify the cold spots, we first examined all polar observations made by the TES radiometer that was co-boresited with MOLA, and made gridded images of ∂ T / ∂ λ , the derivative of the brightness temperature wrt wavelength, 20μ <= λ <= 25μ , over 5o ranges in Ls. A total of 169 cold spots were readily located in the 3 winters (one northern, two southern) during which MOLA operated, and their times of first appearance were noted. We then examined the individual MOLA tracks that crossed these regions from 30 days before, to 30 days after, the cold spot appearances. Three sets of crossing points were assembled: (a) both pairs of tracks were made before the cold spot appearance, (b) both after the appearance, and (c) one before and the other after. For each crossing point, the surface height was interpolated from the 3 nearest altimeter footprints in each of the two tracks. The difference between the resulting pair of heights was averaged over all crossing points, and the RMS variance of the height differences was used as a measure of the statistical error in the measurement. Preliminary results show small height differences before the appearance of a cold spot, as expected, but no abrupt jump in surface height immediately after one appears. This suggests that the cold spots are not formed by deep (>50cm) CO2 snow deposits, but it cannot help us decide between the alternatives of CO2 snowfall or a change in slab ice properties. 1 Smith, Zuber, and Neumann, Science, {294}, 2141-2146, 2001.

Spatial inhomogeneous barrier heights at graphene/semiconductor Schottky junctions

NASA Astrophysics Data System (ADS)

Tomer, Dushyant

Graphene, a semimetal with linear energy dispersion, forms Schottky junction when interfaced with a semiconductor. This dissertation presents temperature dependent current-voltage and scanning tunneling microscopy/spectroscopy (STM/S) measurements performed on graphene Schottky junctions formed with both three and two dimensional semiconductors. To fabricate Schottky junctions, we transfer chemical vapor deposited monolayer graphene onto Si- and C-face SiC, Si, GaAs and MoS2 semiconducting substrates using polymer assisted chemical method. We observe three main type of intrinsic spatial inhomogeneities, graphene ripples, ridges and semiconductor steps in STM imaging that can exist at graphene/semiconductor junctions. Tunneling spectroscopy measurements reveal fluctuations in graphene Dirac point position, which is directly related to the Schottky barrier height. We find a direct correlation of Dirac point variation with the topographic undulations of graphene ripples at the graphene/SiC junction. However, no such correlation is established at graphene/Si and Graphene/GaAs junctions and Dirac point variations are attributed to surface states and trapped charges at the interface. In addition to graphene ripples and ridges, we also observe atomic scale moire patterns at graphene/MoS2 junction due to van der Waals interaction at the interface. Periodic topographic modulations due to moire pattern do not lead to local variation in graphene Dirac point, indicating that moire pattern does not contribute to fluctuations in electronic properties of the heterojunction. We perform temperature dependent current-voltage measurements to investigate the impact of topographic inhomogeneities on electrical properties of the Schottky junctions. We observe temperature dependence in junction parameters, such as Schottky barrier height and ideality factor, for all types of Schottky junctions in forward bias measurements. Standard thermionic emission theory which assumes a perfect smooth interface fails to explain such behavior, hence, we apply a modified emission theory with Gaussian distribution of Schottky barrier heights. The modified theory, applicable to inhomogeneous interfaces, explains the temperature dependent behavior of our Schottky junctions and gives a temperature independent mean barrier height. We attribute the inhomogeneous barrier height to the presence of graphene ripples and ridges in case of SiC and MoS2 while surface states and trapped charges at the interface is dominating in Si and GaAs. Additionally, we observe bias dependent current and barrier height in reverse bias regime also for all Schottky junctions. To explain such behavior, we consider two types of reverse bias conduction mechanisms; Poole-Frenkel and Schottky emission. We find that Poole-Frenkel emission explains the characteristics of graphene/SiC junctions very well. However, both the mechanism fails to interpret the behavior of graphene/Si and graphene/GaAs Schottky junctions. These findings provide insight into the fundamental physics at the interface of graphene/semiconductor junctions.

Critical point relascope sampling for unbiased volume estimation of downed coarse woody debris

Treesearch

Jeffrey H. Gove; Michael S. Williams; Mark J. Ducey; Mark J. Ducey

2005-01-01

Critical point relascope sampling is developed and shown to be design-unbiased for the estimation of log volume when used with point relascope sampling for downed coarse woody debris. The method is closely related to critical height sampling for standing trees when trees are first sampled with a wedge prism. Three alternative protocols for determining the critical...

46 CFR 45.127 - Position of structures, openings, and fittings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... quarter deck; (2) A superstructure deck or a trunk deck and forward of a point 1/4 L from the forward... deck aft of a point 1/4 L abaft the forward perpendicular; or (2) On a superstructure and trunk combination, that is H s or more n height, aft or a point 1/4 L abaft the forward perpendicular. ...

46 CFR 45.127 - Position of structures, openings, and fittings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... quarter deck; (2) A superstructure deck or a trunk deck and forward of a point 1/4 L from the forward... deck aft of a point 1/4 L abaft the forward perpendicular; or (2) On a superstructure and trunk combination, that is H s or more n height, aft or a point 1/4 L abaft the forward perpendicular. ...

Stereographic cloud heights from the imagery of two scan-synchronized geostationary satellites

NASA Technical Reports Server (NTRS)

Minzner, R. A.; Teagle, R. D.; Steranka, J.; Shenk, W. E.

1979-01-01

Scan synchronization of the sensors of two SMS-GOES satellites yields imagery from which cloud heights can be derived stereographically with a theoretical two-sigma random uncertainty of + or - 0.25 km for pairs of satellites separated by 60 degrees of longitude. Systematic height errors due to cloud motion can be kept below 100 m for all clouds with east-west components of speed below hurricane speed, provided the scan synchronization is within 40 seconds at the mid-point latitude, and the spin axis of each satellite is parallel to that of the earth.

Mesoscopic Length Scale Controls the Rheology of Dense Suspensions

NASA Astrophysics Data System (ADS)

Bonnoit, Claire; Lanuza, Jose; Lindner, Anke; Clement, Eric

2010-09-01

From the flow properties of dense granular suspensions on an inclined plane, we identify a mesoscopic length scale strongly increasing with volume fraction. When the flowing layer height is larger than this length scale, a diverging Newtonian viscosity is determined. However, when the flowing layer height drops below this scale, we evidence a nonlocal effective viscosity, decreasing as a power law of the flow height. We establish a scaling relation between this mesoscopic length scale and the suspension viscosity. These results support recent theoretical and numerical results implying collective and clustered granular motion when the jamming point is approached from below.

Mesoscopic length scale controls the rheology of dense suspensions.

PubMed

Bonnoit, Claire; Lanuza, Jose; Lindner, Anke; Clement, Eric

2010-09-03

From the flow properties of dense granular suspensions on an inclined plane, we identify a mesoscopic length scale strongly increasing with volume fraction. When the flowing layer height is larger than this length scale, a diverging Newtonian viscosity is determined. However, when the flowing layer height drops below this scale, we evidence a nonlocal effective viscosity, decreasing as a power law of the flow height. We establish a scaling relation between this mesoscopic length scale and the suspension viscosity. These results support recent theoretical and numerical results implying collective and clustered granular motion when the jamming point is approached from below.

Geodetic satellite observations in North American (solution NA-9)

NASA Technical Reports Server (NTRS)

Mueller, I. I.; Reilly, J. P.; Soler, T.

1972-01-01

A new detailed geoidal map with claimed accuracies of plus or minus 2 meters (on land), based on gravimetric and satellite data, was presented. With the new geoid and the orthometric heights given, more reliable height constraints were calculated and applied. The basic purpose of this experiment was to compute the new solution NA9 by defining the origin of the system, from the point of view of error propagation, in the most favorable position applying inner constraints and imposing new weighted height constraints to all of the stations. The major differences with respect to formerly published adjustments are presented.

De Novo Herpes Simplex Virus VP16 Expression Gates a Dynamic Programmatic Transition and Sets the Latent/Lytic Balance during Acute Infection in Trigeminal Ganglia.

PubMed

Sawtell, Nancy M; Thompson, Richard L

2016-09-01

The life long relationship between herpes simplex virus and its host hinges on the ability of the virus to aggressively replicate in epithelial cells at the site of infection and transport into the nervous system through axons innervating the infection site. Interaction between the virus and the sensory neuron represents a pivot point where largely unknown mechanisms lead to a latent or a lytic infection in the neuron. Regulation at this pivot point is critical for balancing two objectives, efficient widespread seeding of the nervous system and host survival. By combining genetic and in vivo in approaches, our studies reveal that the balance between latent and lytic programs is a process occurring early in the trigeminal ganglion. Unexpectedly, activation of the latent program precedes entry into the lytic program by 12 -14hrs. Importantly, at the individual neuronal level, the lytic program begins as a transition out of this acute stage latent program and this escape from the default latent program is regulated by de novo VP16 expression. Our findings support a model in which regulated de novo VP16 expression in the neuron mediates entry into the lytic cycle during the earliest stages of virus infection in vivo. These findings support the hypothesis that the loose association of VP16 with the viral tegument combined with sensory axon length and transport mechanisms serve to limit arrival of virion associated VP16 into neuronal nuclei favoring latency. Further, our findings point to specialized features of the VP16 promoter that control the de novo expression of VP16 in neurons and this regulation is a key component in setting the balance between lytic and latent infections in the nervous system.

De Novo Herpes Simplex Virus VP16 Expression Gates a Dynamic Programmatic Transition and Sets the Latent/Lytic Balance during Acute Infection in Trigeminal Ganglia

PubMed Central

Sawtell, Nancy M.; Thompson, Richard L.

2016-01-01

The life long relationship between herpes simplex virus and its host hinges on the ability of the virus to aggressively replicate in epithelial cells at the site of infection and transport into the nervous system through axons innervating the infection site. Interaction between the virus and the sensory neuron represents a pivot point where largely unknown mechanisms lead to a latent or a lytic infection in the neuron. Regulation at this pivot point is critical for balancing two objectives, efficient widespread seeding of the nervous system and host survival. By combining genetic and in vivo in approaches, our studies reveal that the balance between latent and lytic programs is a process occurring early in the trigeminal ganglion. Unexpectedly, activation of the latent program precedes entry into the lytic program by 12 -14hrs. Importantly, at the individual neuronal level, the lytic program begins as a transition out of this acute stage latent program and this escape from the default latent program is regulated by de novo VP16 expression. Our findings support a model in which regulated de novo VP16 expression in the neuron mediates entry into the lytic cycle during the earliest stages of virus infection in vivo. These findings support the hypothesis that the loose association of VP16 with the viral tegument combined with sensory axon length and transport mechanisms serve to limit arrival of virion associated VP16 into neuronal nuclei favoring latency. Further, our findings point to specialized features of the VP16 promoter that control the de novo expression of VP16 in neurons and this regulation is a key component in setting the balance between lytic and latent infections in the nervous system. PMID:27607440

Estimating Temperature Retrieval Accuracy Associated With Thermal Band Spatial Resolution Requirements for Center Pivot Irrigation Monitoring and Management

NASA Technical Reports Server (NTRS)

Ryan, Robert E.; Irons, James; Spruce, Joseph P.; Underwood, Lauren W.; Pagnutti, Mary

2006-01-01

This study explores the use of synthetic thermal center pivot irrigation scenes to estimate temperature retrieval accuracy for thermal remote sensed data, such as data acquired from current and proposed Landsat-like thermal systems. Center pivot irrigation is a common practice in the western United States and in other parts of the world where water resources are scarce. Wide-area ET (evapotranspiration) estimates and reliable water management decisions depend on accurate temperature information retrieval from remotely sensed data. Spatial resolution, sensor noise, and the temperature step between a field and its surrounding area impose limits on the ability to retrieve temperature information. Spatial resolution is an interrelationship between GSD (ground sample distance) and a measure of image sharpness, such as edge response or edge slope. Edge response and edge slope are intuitive, and direct measures of spatial resolution are easier to visualize and estimate than the more common Modulation Transfer Function or Point Spread Function. For these reasons, recent data specifications, such as those for the LDCM (Landsat Data Continuity Mission), have used GSD and edge response to specify spatial resolution. For this study, we have defined a 400-800 m diameter center pivot irrigation area with a large 25 K temperature step associated with a 300 K well-watered field surrounded by an infinite 325 K dry area. In this context, we defined the benchmark problem as an easily modeled, highly common stressing case. By parametrically varying GSD (30-240 m) and edge slope, we determined the number of pixels and field area fraction that meet a given temperature accuracy estimate for 400-m, 600-m, and 800-m diameter field sizes. Results of this project will help assess the utility of proposed specifications for the LDCM and other future thermal remote sensing missions and for water resource management.

The unbiasedness of a generalized mirage boundary correction method for Monte Carlo integration estimators of volume

Treesearch

Thomas B. Lynch; Jeffrey H. Gove

2014-01-01

The typical "double counting" application of the mirage method of boundary correction cannot be applied to sampling systems such as critical height sampling (CHS) that are based on a Monte Carlo sample of a tree (or debris) attribute because the critical height (or other random attribute) sampled from a mirage point is generally not equal to the critical...

Effective pollutant emission heights for atmospheric transport modelling based on real-world information.

PubMed

Pregger, Thomas; Friedrich, Rainer

2009-02-01

Emission data needed as input for the operation of atmospheric models should not only be spatially and temporally resolved. Another important feature is the effective emission height which significantly influences modelled concentration values. Unfortunately this information, which is especially relevant for large point sources, is usually not available and simple assumptions are often used in atmospheric models. As a contribution to improve knowledge on emission heights this paper provides typical default values for the driving parameters stack height and flue gas temperature, velocity and flow rate for different industrial sources. The results were derived from an analysis of the probably most comprehensive database of real-world stack information existing in Europe based on German industrial data. A bottom-up calculation of effective emission heights applying equations used for Gaussian dispersion models shows significant differences depending on source and air pollutant and compared to approaches currently used for atmospheric transport modelling.

Remote sensing of Gulf Stream using GEOS-3 radar altimeter

NASA Technical Reports Server (NTRS)

Leitao, C. D.; Huang, N. E.; Parra, C. G.

1978-01-01

Radar altimeter measurements from the GEOS-3 satellite to the ocean surface indicated the presence of expected geostrophic height differences across the the Gulf Stream. Dynamic sea surface heights were found by both editing and filtering the raw sea surface heights and then referencing these processed data to a 5 minute x 5 minute geoid. Any trend between the processed data and the geoid was removed by subtracting out a linear fit to the residuals in the open ocean. The mean current velocity of 107 + or - 29 cm/sec calculated from the dynamic heights for all orbits corresponded with velocities obtained from hydrographic methods. Also, dynamic topographic maps were produced for August, September, and October 1975. Results pointed out limitations in the accuracy of the geoid, height anomaly deteriorations due to filtering, and lack of dense time and space distribution of measurements.

SU-E-T-540: Volumetric Modulated Total Body Irradiation Using a Rotational Lazy Susan-Like Immobilization System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gu, X; Hrycushko, B; Lee, H

2014-06-01

Purpose: Traditional extended SSD total body irradiation (TBI) techniques can be problematic in terms of patient comfort and/or dose uniformity. This work aims to develop a comfortable TBI technique that achieves a uniform dose distribution to the total body while reducing the dose to organs at risk for complications. Methods: To maximize patient comfort, a lazy Susan-like couch top immobilization system which rotates about a pivot point was developed. During CT simulation, a patient is immobilized by a Vac-Lok bag within the body frame. The patient is scanned head-first and then feet-first following 180° rotation of the frame. The twomore » scans are imported into the Pinnacle treatment planning system and concatenated to give a full-body CT dataset. Treatment planning matches multiple isocenter volumetric modulated arc (VMAT) fields of the upper body and multiple isocenter parallel-opposed fields of the lower body. VMAT fields of the torso are optimized to satisfy lung dose constraints while achieving a therapeutic dose to the torso. The multiple isocenter VMAT fields are delivered with an indexed couch, followed by body frame rotation about the pivot point to treat the lower body isocenters. The treatment workflow was simulated with a Rando phantom, and the plan was mapped to a solid water slab phantom for point- and film-dose measurements at multiple locations. Results: The treatment plan of 12Gy over 8 fractions achieved 80.2% coverage of the total body volume within ±10% of the prescription dose. The mean lung dose was 8.1 Gy. All ion chamber measurements were within ±1.7% compared to the calculated point doses. All relative film dosimetry showed at least a 98.0% gamma passing rate using a 3mm/3% passing criteria. Conclusion: The proposed patient comfort-oriented TBI technique provides for a uniform dose distribution within the total body while reducing the dose to the lungs.« less

Parallel pivoting combined with parallel reduction

NASA Technical Reports Server (NTRS)

Alaghband, Gita

1987-01-01

Parallel algorithms for triangularization of large, sparse, and unsymmetric matrices are presented. The method combines the parallel reduction with a new parallel pivoting technique, control over generations of fill-ins and a check for numerical stability, all done in parallel with the work being distributed over the active processes. The parallel technique uses the compatibility relation between pivots to identify parallel pivot candidates and uses the Markowitz number of pivots to minimize fill-in. This technique is not a preordering of the sparse matrix and is applied dynamically as the decomposition proceeds.

Position-related differences in selected morphological body characteristics of top-level handball players.

PubMed

Sibila, Marko; Pori, Primoz

2009-12-01

We aimed to establish the main morphological characteristics of Slovenian junior and senior national handball team players. Morphological characteristics for various player subgroups (goalkeepers, wings, back players and pivots) were also determined so as to establish whether they had distinct profiles. The subjects were 78 handball players who were members of the Slovenian junior and senior national team in the period from 2000 to 2007. A standardised anthropometric protocol was used to assess the subjects' morphological characteristics. The measurements included 23 different anthropometric measures. Data were processed with the SPSS computer programme. First, basic statistical characteristics of anthropometric measures were obtained for all subjects together and then for each group separately. Somatotypes were determined using Heath-Carter's method. Endomorphic, mesomorphic and ectomorphic components were calculated by computer on the basis of formulas. In order to determine differences in the body composition and anthropometric data of the subjects playing in different positions, a one-way analysis of variance was employed. The results show that on average the wings differ the most from the other player groups in terms of their morphological body characteristics. The values of their body height, body mass and the quantity of subcutaneous fat are statistically significantly lower than those of players in the other groups. Goalkeepers are relatively tall, with high values of body mass and low values of transuersal measures. Their skin folds are the most pronounced among all groups on average and their share of subcutaneous fat in total body mass is the highest. Consequently, their endomorphic component of the somatotype is pronounced. Pivots and back players are becoming increasingly similar in terms of their morphological body characteristics. Pivots maintain greater robustness, have a higher quantity of muscle mass as well as more pronounced transversal measures and a mesomorphic component of the somatotype. The results of our study confirm that groups of handball players occupying different positions differ amongst themselves in terms of many measurements. This is a result of specific requirements of handball play which are to be fulfilled by players.

Childbirth in ancient Rome: from traditional folklore to obstetrics.

PubMed

Todman, Donald

2007-04-01

In ancient Rome, childbirth was a hazardous event for both mother and child with high rates of infant and maternal mortality. Traditional Roman medicine centred on folklore and religious practices, but with the development of Hippocratic medicine came significant advances in the care of women during pregnancy and confinement. Midwives or obstetrices played an important role and applied rational scientific practices to improve outcomes. This evolution from folklore to obstetrics was a pivotal point in the history of childbirth.

Micromechanisms with floating pivot

DOEpatents

Garcia, Ernest J.

2001-03-06

A new class of tilting micromechanical mechanisms have been developed. These new mechanisms use floating pivot structures to relieve some of the problems encountered in the use of solid flexible pivots.

3D reconstruction of microminiature objects based on contour line

NASA Astrophysics Data System (ADS)

Li, Cailin; Wang, Qiang; Guo, Baoyun

2009-10-01

A new 3D automatic reconstruction method of micro solid of revolution is presented in this paper. In the implementation procedure of this method, image sequence of the solid of revolution of 360° is obtained, which rotation speed is controlled by motor precisely, in the rotate photographic mode of back light. Firstly, we need calibrate the height of turntable, the size of pixel and rotation axis of turntable. Then according to the calibration result of rotation axis, the height of turntable, rotation angle and the pixel size, the contour points of each image can be transformed into 3D points in the reference coordinate system to generate the point cloud model. Finally, the surface geometrical model of solid of revolution is obtained by using the relationship of two adjacent contours. Experimental results on real images are presented, which demonstrate the effectiveness of the Approach.

Cloud and boundary layer structure over San Nicolas Island during FIRE

NASA Technical Reports Server (NTRS)

Albrecht, Bruce A.; Fairall, Christopher W.; Syrett, William J.; Schubert, Wayne H.; Snider, Jack B.

1990-01-01

The temporal evolution of the structure of the marine boundary layer and of the associated low-level clouds observed in the vicinity of the San Nicolas Island (SNI) is defined from data collected during the First ISCCP Regional Experiment (FIRE) Marine Stratocumulus Intense Field Observations (IFO) (July 1 to 19). Surface, radiosonde, and remote-sensing measurements are used for this analysis. Sounding from the Island and from the ship Point Sur, which was located approximately 100 km northwest of SNI, are used to define variations in the thermodynamic structure of the lower-troposphere on time scales of 12 hours and longer. Time-height sections of potential temperature and equivalent potential temperature clearly define large-scale variations in the height and the strength of the inversion and periods where the conditions for cloud-top entrainment instability (CTEI) are met. Well defined variations in the height and the strength of the inversion were associated with a Cataline Eddy that was present at various times during the experiment and with the passage of the remnants of a tropical cyclone on July 18. The large-scale variations in the mean thermodynamic structure at SNI correlate well with those observed from the Point Sur. Cloud characteristics are defined for 19 days of the experiment using data from a microwave radiometer, a cloud ceilometer, a sodar, and longwave and shortwave radiometers. The depth of the cloud layer is estimated by defining inversion heights from the sodar reflectivity and cloud-base heights from a laser ceilometer. The integrated liquid water obtained from NOAA's microwave radiometer is compared with the adiabatic liquid water content that is calculated by lifting a parcel adiabatically from cloud base. In addition, the cloud structure is characterized by the variability in cloud-base height and in the integrated liquid water.

The Development and Hover Test Application of a Projection Moire Interferometry Blade Displacement Measurement System

NASA Technical Reports Server (NTRS)

Sekula, Martin K.

2012-01-01

Projection moir interferometry (PMI) was employed to measure blade deflections during a hover test of a generic model-scale rotor in the NASA Langley 14x22 subsonic wind tunnel s hover facility. PMI was one of several optical measurement techniques tasked to acquire deflection and flow visualization data for a rotor at several distinct heights above a ground plane. Two of the main objectives of this test were to demonstrate that multiple optical measurement techniques can be used simultaneously to acquire data and to identify and address deficiencies in the techniques. Several PMI-specific technical challenges needed to be addressed during the test and in post-processing of the data. These challenges included developing an efficient and accurate calibration method for an extremely large (65 inch) height range; automating the analysis of the large amount of data acquired during the test; and developing a method to determinate the absolute displacement of rotor blades without a required anchor point measurement. The results indicate that the use of a single-camera/single-projector approach for the large height range reduced the accuracy of the PMI system compared to PMI systems designed for smaller height ranges. The lack of the anchor point measurement (due to a technical issue with one of the other measurement techniques) limited the ability of the PMI system to correctly measure blade displacements to only one of the three rotor heights tested. The new calibration technique reduced the data required by 80 percent while new post-processing algorithms successfully automated the process of locating rotor blades in images, determining the blade quarter chord location, and calculating the blade root and blade tip heights above the ground plane.

WASP (Write a Scientific Paper) using Excel - 2: Pivot tables.

PubMed

Grech, Victor

2018-02-01

Data analysis at the descriptive stage and the eventual presentation of results requires the tabulation and summarisation of data. This exercise should always precede inferential statistics. Pivot tables and pivot charts are one of Excel's most powerful and underutilised features, with tabulation functions that immensely facilitate descriptive statistics. Pivot tables permit users to dynamically summarise and cross-tabulate data, create tables in several dimensions, offer a range of summary statistics and can be modified interactively with instant outputs. Large and detailed datasets are thereby easily manipulated making pivot tables arguably the best way to explore, summarise and present data from many different angles. This second paper in the WASP series in Early Human Development provides pointers for pivot table manipulation in Excel™. Copyright © 2018 Elsevier B.V. All rights reserved.

Raised BMI cut-off for overweight in Greenland Inuit--a review.

PubMed

Andersen, Stig; Fleischer Rex, Karsten; Noahsen, Paneeraq; Sørensen, Hans Christian Florian; Mulvad, Gert; Laurberg, Peter

2013-01-01

Obesity is associated with increased morbidity and premature death. Obesity rates have increased worldwide and the WHO recommends monitoring. A steep rise in body mass index (BMI), a measure of adiposity, was detected in Greenland from 1963 to 1998. Interestingly, the BMI starting point was in the overweight range. This is not conceivable in a disease-free, physically active, pre-western hunter population. This led us to reconsider the cut-off point for overweight among Inuit in Greenland. We found 3 different approaches to defining the cut-off point of high BMI in Inuit. First, the contribution to the height by the torso compared to the legs is relatively high. This causes relatively more kilograms per centimetre of height that increases the BMI by approximately 10% compared to Caucasian whites. Second, defining the cut-off by the upper 90-percentile of BMI from height and weight in healthy young Inuit surveyed in 1963 estimated the cut-off point to be around 10% higher compared to Caucasians. Third, if similar LDL-cholesterol and triglycerides are assumed for a certain BMI in Caucasians, the corresponding BMI in Inuit in both Greenland and Canada is around 10% higher. However, genetic admixture of Greenland Inuit and Caucasian Danes will influence this difference and hamper a clear distinction with time. Defining overweight according to the WHO cut-off of a BMI above 25 kg/m(2) in Greenland Inuit may overestimate the number of individuals with elevated BMI.

Raised BMI cut-off for overweight in Greenland Inuit – a review

PubMed Central

Andersen, Stig; Fleischer Rex, Karsten; Noahsen, Paneeraq; Sørensen, Hans Christian Florian; Mulvad, Gert; Laurberg, Peter

2013-01-01

Background Obesity is associated with increased morbidity and premature death. Obesity rates have increased worldwide and the WHO recommends monitoring. A steep rise in body mass index (BMI), a measure of adiposity, was detected in Greenland from 1963 to 1998. Interestingly, the BMI starting point was in the overweight range. This is not conceivable in a disease-free, physically active, pre-western hunter population. Objective This led us to reconsider the cut-off point for overweight among Inuit in Greenland. Design and findings We found 3 different approaches to defining the cut-off point of high BMI in Inuit. First, the contribution to the height by the torso compared to the legs is relatively high. This causes relatively more kilograms per centimetre of height that increases the BMI by approximately 10% compared to Caucasian whites. Second, defining the cut-off by the upper 90-percentile of BMI from height and weight in healthy young Inuit surveyed in 1963 estimated the cut-off point to be around 10% higher compared to Caucasians. Third, if similar LDL-cholesterol and triglycerides are assumed for a certain BMI in Caucasians, the corresponding BMI in Inuit in both Greenland and Canada is around 10% higher. However, genetic admixture of Greenland Inuit and Caucasian Danes will influence this difference and hamper a clear distinction with time. Conclusion Defining overweight according to the WHO cut-off of a BMI above 25 kg/m2 in Greenland Inuit may overestimate the number of individuals with elevated BMI. PMID:23986904

Current progress in the development of a totally implantable Gyro centrifugal artificial heart.

PubMed

Takami, Y; Ohtsuka, G; Mueller, J; Ebner, M; Tayama, E; Ohashi, Y; Taylor, D; Fernandes, J; Schima, H; Schmallegger, H; Wolner, E; Nosé, Y

1998-01-01

A totally implantable centrifugal artificial heart has been developed using a miniaturized pivot bearing supported centrifugal pump (Gyro PI pump). The authors report current progress in its development. The Gyro PI-601 has a priming volume of 20 ml, weighs 100 g, has a height of 60 mm, and has a diameter of 65 mm. This pump can provide 8 L/min against 150 mmHg at 2,250 rpm. It is driven by an miniaturized DC brushless motor with the coils fixed in a plastic mold that is waterproof and made of titanium (weight, 204 g; height, 18 mm; diameter, 65 mm). In this centrifugal artificial heart, two Gyro PI pumps are implanted independently to replace cardiac function without resecting the native heart. Its anatomic and surgical feasibility were confirmed experimentally. The Gyro PI-601 was implanted as a right or left ventricular assist device in the preperitoneal space of five calves. All five tests proceeded without any thromboembolic symptoms. One of five tests was extended more than 1 month to confirm the long-term feasibility of the Gyro PI-601 pump system. Based on the satisfactory results of the in vivo tests, the material conversion of the Gyro PI from polycarbonate to titanium alloy (Ti-6A1-4V) was undertaken to improve its biocompatibility for long-term implantation.

Wind-tunnel Modelling of Dispersion from a Scalar Area Source in Urban-Like Roughness

NASA Astrophysics Data System (ADS)

Pascheke, Frauke; Barlow, Janet F.; Robins, Alan

2008-01-01

A wind-tunnel study was conducted to investigate ventilation of scalars from urban-like geometries at neighbourhood scale by exploring two different geometries a uniform height roughness and a non-uniform height roughness, both with an equal plan and frontal density of λ p = λ f = 25%. In both configurations a sub-unit of the idealized urban surface was coated with a thin layer of naphthalene to represent area sources. The naphthalene sublimation method was used to measure directly total area-averaged transport of scalars out of the complex geometries. At the same time, naphthalene vapour concentrations controlled by the turbulent fluxes were detected using a fast Flame Ionisation Detection (FID) technique. This paper describes the novel use of a naphthalene coated surface as an area source in dispersion studies. Particular emphasis was also given to testing whether the concentration measurements were independent of Reynolds number. For low wind speeds, transfer from the naphthalene surface is determined by a combination of forced and natural convection. Compared with a propane point source release, a 25% higher free stream velocity was needed for the naphthalene area source to yield Reynolds-number-independent concentration fields. Ventilation transfer coefficients w T / U derived from the naphthalene sublimation method showed that, whilst there was enhanced vertical momentum exchange due to obstacle height variability, advection was reduced and dispersion from the source area was not enhanced. Thus, the height variability of a canopy is an important parameter when generalising urban dispersion. Fine resolution concentration measurements in the canopy showed the effect of height variability on dispersion at street scale. Rapid vertical transport in the wake of individual high-rise obstacles was found to generate elevated point-like sources. A Gaussian plume model was used to analyse differences in the downstream plumes. Intensified lateral and vertical plume spread and plume dilution with height was found for the non-uniform height roughness.

Standardized pivot shift test improves measurement accuracy.

PubMed

Hoshino, Yuichi; Araujo, Paulo; Ahlden, Mattias; Moore, Charity G; Kuroda, Ryosuke; Zaffagnini, Stefano; Karlsson, Jon; Fu, Freddie H; Musahl, Volker

2012-04-01

The variability of the pivot shift test techniques greatly interferes with achieving a quantitative and generally comparable measurement. The purpose of this study was to compare the variation of the quantitative pivot shift measurements with different surgeons' preferred techniques to a standardized technique. The hypothesis was that standardizing the pivot shift test would improve consistency in the quantitative evaluation when compared with surgeon-specific techniques. A whole lower body cadaveric specimen was prepared to have a low-grade pivot shift on one side and high-grade pivot shift on the other side. Twelve expert surgeons performed the pivot shift test using (1) their preferred technique and (2) a standardized technique. Electromagnetic tracking was utilized to measure anterior tibial translation and acceleration of the reduction during the pivot shift test. The variation of the measurement was compared between the surgeons' preferred technique and the standardized technique. The anterior tibial translation during pivot shift test was similar between using surgeons' preferred technique (left 24.0 ± 4.3 mm; right 15.5 ± 3.8 mm) and using standardized technique (left 25.1 ± 3.2 mm; right 15.6 ± 4.0 mm; n.s.). However, the variation in acceleration was significantly smaller with the standardized technique (left 3.0 ± 1.3 mm/s(2); right 2.5 ± 0.7 mm/s(2)) compared with the surgeons' preferred technique (left 4.3 ± 3.3 mm/s(2); right 3.4 ± 2.3 mm/s(2); both P < 0.01). Standardizing the pivot shift test maneuver provides a more consistent quantitative evaluation and may be helpful in designing future multicenter clinical outcome trials. Diagnostic study, Level I.

Evaluating a Pivot-Based Approach for Bilingual Lexicon Extraction

PubMed Central

Kim, Jae-Hoon; Kwon, Hong-Seok; Seo, Hyeong-Won

2015-01-01

A pivot-based approach for bilingual lexicon extraction is based on the similarity of context vectors represented by words in a pivot language like English. In this paper, in order to show validity and usability of the pivot-based approach, we evaluate the approach in company with two different methods for estimating context vectors: one estimates them from two parallel corpora based on word association between source words (resp., target words) and pivot words and the other estimates them from two parallel corpora based on word alignment tools for statistical machine translation. Empirical results on two language pairs (e.g., Korean-Spanish and Korean-French) have shown that the pivot-based approach is very promising for resource-poor languages and this approach observes its validity and usability. Furthermore, for words with low frequency, our method is also well performed. PMID:25983745

LMS tables for waist circumference and waist–height ratio in Colombian adults: analysis of nationwide data 2010

PubMed Central

Ramírez-Vélez, R; Correa-Bautista, J E; Martínez-Torres, J; Méneses-Echavez, J F; González-Ruiz, K; González-Jiménez, E; Schmidt-RioValle, J; Lobelo, F

2016-01-01

Background/Objectives: Indices predictive of central obesity include waist circumference (WC) and waist-to-height ratio (WHtR). These data are lacking for Colombian adults. This study aims at establishing smoothed centile charts and LMS tables for WC and WHtR; appropriate cutoffs were selected using receiver-operating characteristic analysis based on data from the representative sample. Subjects/Methods: We used data from the cross-sectional, national representative nutrition survey (ENSIN, 2010). A total of 83 220 participants (aged 20–64) were enroled. Weight, height, body mass index (BMI), WC and WHtR were measured and percentiles calculated using the LMS method (L (curve Box-Cox), M (curve median), and S (curve coefficient of variation)). Receiver operating characteristics curve analyses were used to evaluate the optimal cutoff point of WC and WHtR for overweight and obesity based on WHO definitions. Results: Reference values for WC and WHtR are presented. Mean WC and WHtR increased with age for both genders. We found a strong positive correlation between WC and BMI (r=0.847, P< 0.01) and WHtR and BMI (r=0.878, P<0.01). In obese men, the cutoff point value is 96.6 cm for the WC. In women, the cutoff point value is 91.0 cm for the WC. Receiver operating characteristic curve for WHtR was also obtained and the cutoff point value of 0.579 in men, and in women the cutoff point value was 0.587. A high sensitivity and specificity were obtained. Conclusions: This study presents first reference values of WC and WHtR for Colombians aged 20–64. Through LMS tables for adults, we hope to provide quantitative tools to study obesity and its complications. PMID:27026425

Morphologic Quality of DSMs Based on Optical and Radar Space Imagery

NASA Astrophysics Data System (ADS)

Sefercik, U. G.; Bayik, C.; Karakis, S.; Jacobsen, K.

2011-09-01

Digital Surface Models (DSMs) are representing the visible surface of the earth by the height corresponding to its X-, Y-location and height value Z. The quality of a DSM can be described by the accuracy and the morphologic details. Both depend upon the used input information, the used technique and the roughness of the terrain. The influence of the topographic details to the DSM quality is shown for the test fields Istanbul and Zonguldak. Zonguldak has a rough mountainous character with heights from sea level up to 1640m, while Istanbul is dominated by rolling hills going up to an elevation of 435m. DSMs from SPOT-5, the SRTM C-band height models and ASTER GDEM have been investigated. The DSMs have been verified with height models from large scale aerial photos being more accurate and including morphologic details. It was necessary to determine and respect shifts of the height models caused by datum problems and orientation of the height models. The DSM quality is analyzed depending upon the terrain inclination. The DSM quality differs for both test fields. The morphologic quality depends upon the point spacing of the analyzed DSMs and the terrain characteristics.

Misuse study of latch attachment: a series of frontal sled tests.

PubMed

Menon, Rajiv; Ghati, Yoganand

2007-01-01

This study was initiated to quantify the effects of the misuse in LATCH lower webbing. In the short period since the implementation of the LATCH system several cases of potential misuses have been reported. A series of sled tests in frontal impact mode were conducted with various misuse conditions (loose attachment of LATCH lower webbing, misrouting of LATCH lower webbing and child seat back inclination) for both forward and rearward facing child safety seats (FFCSS and RFCSS). Results from these tests are compared and discussed with that of the standard test with no misuse and showed that as the slack in the lower LATCH webbing increased, ATD injury measures exceeded the limits. The FFCSS tests in the reclined condition yielded lower injury values for all except the chest G's when compared to the standard upright test. In the misrouting tests the ATD kinematics depended on the routing pivot point, the lower the pivot point the better the ATD kinematics. Similar findings were also observed in the RFCSS tests. The use of top tether with the FFCSS substantially improved the performance of the Hybrid III 3 year old ATD in spite of misuse conditions and the injury values were lower than the corresponding tests with no top tether. The effective reduction was 37% in the HIC values, 6% in the chest G's, 30% in the head excursion, 22 % in the knee excursion and finally 37 % reduction in the Nij values.

A new paradigm for human stick balancing: a suspended not an inverted pendulum.

PubMed

Lee, Kwee-Yum; O'Dwyer, Nicholas; Halaki, Mark; Smith, Richard

2012-09-01

We studied 14 skilled subjects balancing a stick (a television antenna, 52 cm, 34 g) on their middle fingertip. Comprehensive three-dimensional analyses revealed that the movement of the finger was 1.75 times that of the stick tip, such that the balanced stick behaved more like a normal noninverted pendulum than the inverted pendulum common to engineering models for stick balancing using motors. The average relation between the torque applied to the stick and its angle of deviation from the vertical was highly linear, consistent with simple harmonic motion. We observed clearly greater rotational movement of the stick in the anteroposterior plane than the mediolateral plane. Despite this magnitude difference, the duration of stick oscillatory cycles was very similar in both planes, again consistent with simple harmonic motion. The control parameter in balancing was the ratio of active torque applied to the stick relative to gravitational torque. It determined both the pivot point and oscillatory cycle period of the pendulum. The pivot point was located at the radius of gyration (about the centre of mass) of the stick from its centre of mass, showing that the subjects attuned to the gravitational dynamics and mass distribution of the stick. Hence, the key to controlling instability here was mastery of the physics of the unstable object. The radius of gyration may--similar to centre of mass--contribute to the kinesthesis of rotating limb segments and control of their gravitational dynamics.

Reconstructing Tropical Pacific Sea Level Variability for the Period 1961-2002 Using a Linear Multimode Model

NASA Astrophysics Data System (ADS)

Greatbatch, Richard J.; Zhu, Xiaoting; Claus, Martin

2018-03-01

Monthly mean sea level anomalies in the tropical Pacific for the period 1961-2002 are reconstructed using a linear, multimode model driven by monthly mean wind stress anomalies from the NCEP/NCAR and ERA-40 reanalysis products. Overall, the sea level anomalies reconstructed by both wind stress products agree well with the available tide gauge data, although with poor performance at Kanton Island in the western-central equatorial Pacific and reduced amplitude at Christmas Island. The reduced performance is related to model error in locating the pivot point in sea level variability associated with the so-called "tilt" mode. We present evidence that the pivot point was further west during the period 1993-2014 than during the period 1961-2002 and attribute this to a persistent upward trend in the zonal wind stress variance along the equator west of 160° W throughout the period 1961-2014. Experiments driven by the zonal component of the wind stress alone reproduce much of the trend in sea level found in the experiments driven by both components of the wind stress. The experiments show an upward trend in sea level in the eastern tropical Pacific over the period 1961-2002, but with a much stronger upward trend when using the NCEP/NCAR product. We argue that the latter is related to an overly strong eastward trend in zonal wind stress in the eastern-central Pacific that is believed to be a spurious feature of the NCEP/NCAR product.

Basic psychometric properties of the transfer assessment instrument (version 3.0).

PubMed

Tsai, Chung-Ying; Rice, Laura A; Hoelmer, Claire; Boninger, Michael L; Koontz, Alicia M

2013-12-01

To refine the Transfer Assessment Instrument (TAI 2.0), develop a training program for the TAI, and analyze the basic psychometric properties of the TAI 3.0, including reliability, standard error of measurement (SEM), minimal detectable change (MDC), and construct validity. Repeated measures. A winter sports clinic for disabled veterans. Wheelchair users (N=41) who perform sitting-pivot or standing-pivot transfers. Not applicable. TAI version 3.0, intraclass correlation coefficients, SEMs, and MDCs for reliable measurement of raters' responses. Spearman correlation coefficient, 1-way analysis of variance, and independent t tests to evaluate construct validity. TAI 3.0 had acceptable to high levels of reliability (range, .74-.88). The SEMs for part 1, part 2, and final scores ranged from .45 to .75. The MDC was 1.5 points on the 10-point scale for the final score. There were weak correlations (ρ range, -.13 to .25; P>.11) between TAI final scores and subjects' characteristics (eg, sex, body mass index, age, type of disability, length of wheelchair use, grip and elbow strength, sitting balance). With comprehensive training, the refined TAI 3.0 yields high reliability among raters of different clinical backgrounds and experience. TAI 3.0 was unbiased toward certain physical characteristics that may influence transfer. TAI fills a void in the field by providing a quantitative measurement of transfers and a tool that can be used to detect problems and guide transfer training. Copyright © 2013 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Implied Dynamics Biases the Visual Perception of Velocity

PubMed Central

La Scaleia, Barbara; Zago, Myrka; Moscatelli, Alessandro; Lacquaniti, Francesco; Viviani, Paolo

2014-01-01

We expand the anecdotic report by Johansson that back-and-forth linear harmonic motions appear uniform. Six experiments explore the role of shape and spatial orientation of the trajectory of a point-light target in the perceptual judgment of uniform motion. In Experiment 1, the target oscillated back-and-forth along a circular arc around an invisible pivot. The imaginary segment from the pivot to the midpoint of the trajectory could be oriented vertically downward (consistent with an upright pendulum), horizontally leftward, or vertically upward (upside-down). In Experiments 2 to 5, the target moved uni-directionally. The effect of suppressing the alternation of movement directions was tested with curvilinear (Experiment 2 and 3) or rectilinear (Experiment 4 and 5) paths. Experiment 6 replicated the upright condition of Experiment 1, but participants were asked to hold the gaze on a fixation point. When some features of the trajectory evoked the motion of either a simple pendulum or a mass-spring system, observers identified as uniform the kinematic profiles close to harmonic motion. The bias towards harmonic motion was most consistent in the upright orientation of Experiment 1 and 6. The bias disappeared when the stimuli were incompatible with both pendulum and mass-spring models (Experiments 3 to 5). The results are compatible with the hypothesis that the perception of dynamic stimuli is biased by the laws of motion obeyed by natural events, so that only natural motions appear uniform. PMID:24667578

A continuous scale-space method for the automated placement of spot heights on maps

NASA Astrophysics Data System (ADS)

Rocca, Luigi; Jenny, Bernhard; Puppo, Enrico

2017-12-01

Spot heights and soundings explicitly indicate terrain elevation on cartographic maps. Cartographers have developed design principles for the manual selection, placement, labeling, and generalization of spot height locations, but these processes are work-intensive and expensive. Finding an algorithmic criterion that matches the cartographers' judgment in ranking the significance of features on a terrain is a difficult endeavor. This article proposes a method for the automated selection of spot heights locations representing natural features such as peaks, saddles and depressions. A lifespan of critical points in a continuous scale-space model is employed as the main measure of the importance of features, and an algorithm and a data structure for its computation are described. We also introduce a method for the comparison of algorithmically computed spot height locations with manually produced reference compilations. The new method is compared with two known techniques from the literature. Results show spot height locations that are closer to reference spot heights produced manually by swisstopo cartographers, compared to previous techniques. The introduced method can be applied to elevation models for the creation of topographic and bathymetric maps. It also ranks the importance of extracted spot height locations, which allows for a variation in the size of symbols and labels according to the significance of represented features. The importance ranking could also be useful for adjusting spot height density of zoomable maps in real time.

Measuring perceived ceiling height in a visual comparison task.

PubMed

von Castell, Christoph; Hecht, Heiko; Oberfeld, Daniel

2017-03-01

When judging interior space, a dark ceiling is judged to be lower than a light ceiling. The method of metric judgments (e.g., on a centimetre scale) that has typically been used in such tasks may reflect a genuine perceptual effect or it may reflect a cognitively mediated impression. We employed a height-matching method in which perceived ceiling height had to be matched with an adjustable pillar, thus obtaining psychometric functions that allowed for an estimation of the point of subjective equality (PSE) and the difference limen (DL). The height-matching method developed in this paper allows for a direct visual match and does not require metric judgment. It has the added advantage of providing superior precision. Experiment 1 used ceiling heights between 2.90 m and 3.00 m. The PSE proved sensitive to slight changes in perceived ceiling height. The DL was about 3% of the physical ceiling height. Experiment 2 found similar results for lower (2.30 m to 2.50 m) and higher (3.30 m to 3.50 m) ceilings. In Experiment 3, we additionally varied ceiling lightness (light grey vs. dark grey). The height matches showed that the light ceiling appeared significantly higher than the darker ceiling. We therefore attribute the influence of ceiling lightness on perceived ceiling height to a direct perceptual rather than a cognitive effect.

Variable Geometry Aircraft Wing Supported by Struts And/Or Trusses

NASA Technical Reports Server (NTRS)

Melton, John E. (Inventor); Dudley, Michael R. (Inventor)

2016-01-01

The present invention provides an aircraft having variable airframe geometry for accommodating efficient flight. The aircraft includes an elongated fuselage, an oblique wing pivotally connected with said fuselage, a wing pivoting mechanism connected with said oblique wing and said fuselage, and a brace operably connected between said oblique wing and said fuselage. The present invention also provides an aircraft having an elongated fuselage, an oblique wing pivotally connected with said fuselage, a wing pivoting mechanism connected with said oblique wing and said fuselage, a propulsion system pivotally connected with said oblique wing, and a brace operably connected between said propulsion system and said fuselage.

Numerical Assessment of Four-Port Through-Flow Wave Rotor Cycles with Passage Height Variation

NASA Technical Reports Server (NTRS)

Paxson, D. E.; Lindau, Jules W.

1997-01-01

The potential for improved performance of wave rotor cycles through the use of passage height variation is examined. A Quasi-one-dimensional CFD code with experimentally validated loss models is used to determine the flowfield in the wave rotor passages. Results indicate that a carefully chosen passage height profile can produce substantial performance gains. Numerical performance data are presented for a specific profile, in a four-port, through-flow cycle design which yielded a computed 4.6% increase in design point pressure ratio over a comparably sized rotor with constant passage height. In a small gas turbine topping cycle application, this increased pressure ratio would reduce specific fuel consumption to 22% below the un-topped engine; a significant improvement over the already impressive 18% reductions predicted for the constant passage height rotor. The simulation code is briefly described. The method used to obtain rotor passage height profiles with enhanced performance is presented. Design and off-design results are shown using two different computational techniques. The paper concludes with some recommendations for further work.

Pedicle screw placement in patients with variant atlas pedicle.

PubMed

Zhang, Qiang-Hua; Li, Hai-Dong; Min, Ji-Kang

2016-08-01

To investigate how the anatomy of variant atlas vertebra impacts on the strategy used to place pedicle screws used to treat atlantoaxial instability. The study enrolled patients with cervical instability who had a posterior arch pedicle height <3.5 mm at the anchor point, a vertebral artery groove height <3.5 mm, or both. Pedicle screws were fitted according to the anatomy of the variant atlas vertebra. Patients were followed-up to evaluate accuracy of the screw placement and maintenance of cervical stability. A total of 28 patients were enrolled. The mean height of the atlas pedicle proximal section was >5.0 mm. For the vertebral artery groove, the height of the lateral region was significantly greater than that of the medial region. Approximately 60% of atlas vertebrae had lateral heights >3.5 mm (34 of 56). The majority of the posterior arch heights were <3.0 mm. There were no perioperative or postoperative complications observed. Pedicle screw placement in the lateral pedicle region is the safest and most reliable strategy to treat variant atlas pedicles. © The Author(s) 2016.

The Shortlist Method for fast computation of the Earth Mover's Distance and finding optimal solutions to transportation problems.

PubMed

Gottschlich, Carsten; Schuhmacher, Dominic

2014-01-01

Finding solutions to the classical transportation problem is of great importance, since this optimization problem arises in many engineering and computer science applications. Especially the Earth Mover's Distance is used in a plethora of applications ranging from content-based image retrieval, shape matching, fingerprint recognition, object tracking and phishing web page detection to computing color differences in linguistics and biology. Our starting point is the well-known revised simplex algorithm, which iteratively improves a feasible solution to optimality. The Shortlist Method that we propose substantially reduces the number of candidates inspected for improving the solution, while at the same time balancing the number of pivots required. Tests on simulated benchmarks demonstrate a considerable reduction in computation time for the new method as compared to the usual revised simplex algorithm implemented with state-of-the-art initialization and pivot strategies. As a consequence, the Shortlist Method facilitates the computation of large scale transportation problems in viable time. In addition we describe a novel method for finding an initial feasible solution which we coin Modified Russell's Method.

The Shortlist Method for Fast Computation of the Earth Mover's Distance and Finding Optimal Solutions to Transportation Problems

PubMed Central

Gottschlich, Carsten; Schuhmacher, Dominic

2014-01-01

Finding solutions to the classical transportation problem is of great importance, since this optimization problem arises in many engineering and computer science applications. Especially the Earth Mover's Distance is used in a plethora of applications ranging from content-based image retrieval, shape matching, fingerprint recognition, object tracking and phishing web page detection to computing color differences in linguistics and biology. Our starting point is the well-known revised simplex algorithm, which iteratively improves a feasible solution to optimality. The Shortlist Method that we propose substantially reduces the number of candidates inspected for improving the solution, while at the same time balancing the number of pivots required. Tests on simulated benchmarks demonstrate a considerable reduction in computation time for the new method as compared to the usual revised simplex algorithm implemented with state-of-the-art initialization and pivot strategies. As a consequence, the Shortlist Method facilitates the computation of large scale transportation problems in viable time. In addition we describe a novel method for finding an initial feasible solution which we coin Modified Russell's Method. PMID:25310106

Joint US Navy/US Air Force climatic study of the upper atmosphere. Volume 7: July

NASA Astrophysics Data System (ADS)

Changery, Michael J.; Williams, Claude N.; Dickenson, Michael L.; Wallace, Brian L.

1989-07-01

The upper atmosphere was studied based on 1980 to 1985 twice daily gridded analysis produced by the European Centre for Medium Range Weather Forecasts. This volume is for the month of July. Included are global analyses of: (1) Mean temperature/standard deviation; (2) Mean geopotential height/standard deviation; (3) Mean density/standard deviation; (4) Height and vector standard deviation (all at 13 pressure levels - 1000, 850, 700, 500, 400, 300, 250, 200, 150, 100, 70, 50, 30 mb); (5) Mean dew point standard deviation at levels 1000 through 30 mb; and (6) Jet stream at levels 500 through 30 mb. Also included are global 5 degree grid point wind roses for the 13 pressure levels.

Joint US Navy/US Air Force climatic study of the upper atmosphere. Volume 10: October

NASA Astrophysics Data System (ADS)

Changery, Michael J.; Williams, Claude N.; Dickenson, Michael L.; Wallace, Brian L.

1989-07-01

The upper atmosphere was studied based on 1980 to 1985 twice daily gridded analysis produced by the European Centre for Medium Range Weather Forecasts. This volume is for the month of October. Included are global analyses of: (1) Mean temperature/standard deviation; (2) Mean geopotential height/standard deviation; (3) Mean density/standard deviation; (4) Height and vector standard deviation (all at 13 pressure levels - 1000, 850, 700, 500, 400, 300, 250, 200, 150, 100, 70, 50, 30 mb); (5) Mean dew point/standard deviation at levels 1000 through 30 mb; and (6) Jet stream at levels 500 through 30 mb. Also included are global 5 degree grid point wind roses for the 13 pressure levels.

Joint US Navy/US Air Force climatic study of the upper atmosphere. Volume 3: March

NASA Astrophysics Data System (ADS)

Changery, Michael J.; Williams, Claude N.; Dickenson, Michael L.; Wallace, Brian L.

1989-11-01

The upper atmosphere was studied based on 1980 to 1985 twice daily gridded analysis produced by the European Centre for Medium Range Weather Forecasts. This volume is for the month of March. Included are global analyses of: (1) Mean Temperature Standard Deviation; (2) Mean Geopotential Height Standard Deviation; (3) Mean Density Standard Deviation; (4) Height and Vector Standard Deviation (all for 13 pressure levels - 1000, 850, 700, 500, 400, 300, 250, 200, 150, 100, 70, 50, 30 mb); (5) Mean Dew Point Standard Deviation for levels 1000 through 30 mb; and (6) Jet stream for levels 500 through 30 mb. Also included are global 5 degree grid point wind roses for the 13 pressure levels.

Joint US Navy/US Air Force climatic study of the upper atmosphere. Volume 2: February

NASA Astrophysics Data System (ADS)

Changery, Michael J.; Williams, Claude N.; Dickenson, Michael L.; Wallace, Brian L.

1989-09-01

The upper atmosphere was studied based on 1980 to 1985 twice daily gridded analyses produced by the European Centre for Medium Range Weather Forecasts. This volume is for the month of February. Included are global analyses of: (1) Mean temperature standard deviation; (2) Mean geopotential height standard deviation; (3) Mean density standard deviation; (4) Height and vector standard deviation (all for 13 pressure levels - 1000, 850, 700, 500, 400, 300, 250, 200, 150, 100, 70, 50, 30 mb); (5) Mean dew point standard deviation for the 13 levels; and (6) Jet stream for levels 500 through 30 mb. Also included are global 5 degree grid point wind roses for the 13 pressure levels.

Joint US Navy/US Air Force climatic study of the upper atmosphere. Volume 4: April

NASA Astrophysics Data System (ADS)

Changery, Michael J.; Williams, Claude N.; Dickenson, Michael L.; Wallace, Brian L.

1989-07-01

The upper atmosphere was studied based on 1980 to 1985 twice daily gridded analyses produced by the European Centre for Medium Range Weather Forecasts. This volume is for the month of April. Included are global analyses of: (1) Mean temperature standard deviation; (2) Mean geopotential height standard deviation; (3) Mean density standard deviation; (4) Height and vector standard deviation (all for 13 pressure levels - 1000, 850, 700, 500, 400, 300, 250, 200, 150, 100, 70, 50, 30 mb); (5) Mean dew point standard deviation for the 13 levels; and (6) Jet stream for levels 500 through 30 mb. Also included are global 5 degree grid point wind roses for the 13 pressure levels.

Branch-point energies and the band-structure lineup at Schottky contacts and heterostrucures

NASA Astrophysics Data System (ADS)

Mönch, Winfried

2011-06-01

Empirical branch-point energies of Si, the group-III nitrides AlN, GaN, and InN, and the group-II and group-III oxides MgO, ZnO, Al2O3 and In2O3 are determined from experimental valance-band offsets of their heterostructures. For Si, GaN, and MgO, these values agree with the branch-point energies obtained from the barrier heights of their Schottky contacts. The empirical branch-point energies of Si and the group-III nitrides are in very good agreement with results of previously published calculations using quite different approaches such as the empirical tight-binding approximation and modern electronic-structure theory. In contrast, the empirical branch-point energies of the group-II and group-III oxides do not confirm the respective theoretical results. As at Schottky contacts, the band-structure lineup at heterostructures is also made up of a zero-charge-transfer term and an intrinsic electric-dipole contribution. Hence, valence-band offsets are not equal to the difference of the branch-point energies of the two semiconductors forming the heterostructure. The electric-dipole term may be described by the electronegativity difference of the two solids in contact. A detailed analysis of experimental Si Schottky barrier heights and heterostructure valence-band offsets explains and proves these conclusions.

Three-Dimensional Structure and Evolution of Extreme-Ultraviolet Bright Points Observed by STEREO/SECCHI/EUVI

NASA Technical Reports Server (NTRS)

Kwon, Ryun Young; Chae, Jongchul; Davila, Joseph M.; Zhang, Jie; Moon, Yong-Jae; Poomvises, Watanachak; Jones, Shaela I.

2012-01-01

We unveil the three-dimensional structure of quiet-Sun EUV bright points and their temporal evolution by applying a triangulation method to time series of images taken by SECCHI/EUVI on board the STEREO twin spacecraft. For this study we examine the heights and lengths as the components of the three-dimensional structure of EUV bright points and their temporal evolutions. Among them we present three bright points which show three distinct changes in the height and length: decreasing, increasing, and steady. We show that the three distinct changes are consistent with the motions (converging, diverging, and shearing, respectively) of their photospheric magnetic flux concentrations. Both growth and shrinkage of the magnetic fluxes occur during their lifetimes and they are dominant in the initial and later phases, respectively. They are all multi-temperature loop systems which have hot loops (approx. 10(exp 6.2) K) overlying cooler ones (approx 10(exp 6.0) K) with cool legs (approx 10(exp 4.9) K) during their whole evolutionary histories. Our results imply that the multi-thermal loop system is a general character of EUV bright points. We conclude that EUV bright points are flaring loops formed by magnetic reconnection and their geometry may represent the reconnected magnetic field lines rather than the separator field lines.

Point Intercept (PO)

Treesearch

John F. Caratti

2006-01-01

The FIREMON Point Intercept (PO) method is used to assess changes in plant species cover or ground cover for a macroplot. This method uses a narrow diameter sampling pole or sampling pins, placed at systematic intervals along line transects to sample within plot variation and quantify statistically valid changes in plant species cover and height over time. Plant...

Accuracy assessment of the global TanDEM-X Digital Elevation Model with GPS data

NASA Astrophysics Data System (ADS)

Wessel, Birgit; Huber, Martin; Wohlfart, Christian; Marschalk, Ursula; Kosmann, Detlev; Roth, Achim

2018-05-01

The primary goal of the German TanDEM-X mission is the generation of a highly accurate and global Digital Elevation Model (DEM) with global accuracies of at least 10 m absolute height error (linear 90% error). The global TanDEM-X DEM acquired with single-pass SAR interferometry was finished in September 2016. This paper provides a unique accuracy assessment of the final TanDEM-X global DEM using two different GPS point reference data sets, which are distributed across all continents, to fully characterize the absolute height error. Firstly, the absolute vertical accuracy is examined by about three million globally distributed kinematic GPS (KGPS) points derived from 19 KGPS tracks covering a total length of about 66,000 km. Secondly, a comparison is performed with more than 23,000 "GPS on Bench Marks" (GPS-on-BM) points provided by the US National Geodetic Survey (NGS) scattered across 14 different land cover types of the US National Land Cover Data base (NLCD). Both GPS comparisons prove an absolute vertical mean error of TanDEM-X DEM smaller than ±0.20 m, a Root Means Square Error (RMSE) smaller than 1.4 m and an excellent absolute 90% linear height error below 2 m. The RMSE values are sensitive to land cover types. For low vegetation the RMSE is ±1.1 m, whereas it is slightly higher for developed areas (±1.4 m) and for forests (±1.8 m). This validation confirms an outstanding absolute height error at 90% confidence level of the global TanDEM-X DEM outperforming the requirement by a factor of five. Due to its extensive and globally distributed reference data sets, this study is of considerable interests for scientific and commercial applications.

Assessment of the most recent satellite based digital elevation models of Egypt

NASA Astrophysics Data System (ADS)

Rabah, Mostafa; El-Hattab, Ahmed; Abdallah, Mohamed

2017-12-01

Digital Elevation Model (DEM) is crucial to a wide range of surveying and civil engineering applications worldwide. Some of the DEMs such as ASTER, SRTM1 and SRTM3 are freely available open source products. In order to evaluate the three DEMs, the contribution of EGM96 are removed and all DEMs heights are becoming ellipsoidal height. This step was done to avoid the errors occurred due to EGM96. 601 points of observed ellipsoidal heights compared with the three DEMs, the results show that the SRTM1 is the most accurate one, that produces mean height difference and standard deviations equal 2.89 and ±8.65 m respectively. In order to increase the accuracy of SRTM1 in EGYPT, a precise Global Geopotential Model (GGM) is needed to convert the SRTM1 ellipsoidal height to orthometric height, so that, we quantify the precision of most-recent released GGM (five models). The results show that, the GECO model is the best fit global models over Egypt, which produces a standard deviation of geoid undulation differences equals ±0.42 m over observed 17 HARN GPS/leveling stations. To confirm an enhanced DEM in EGYPT, the two orthometric height models (SRTM1 ellipsoidal height + EGM96) and (SRTM1 ellipsoidal height + GECO) are assessment with 17 GPS/leveling stations and 112 orthometric height stations, the results show that the estimated height differences between the SRTM1 before improvements and the enhanced model are at rate of 0.44 m and 0.06 m respectively.

Comparison of treatment effect sizes from pivotal and postapproval trials of novel therapeutics approved by the FDA based on surrogate markers of disease: a meta-epidemiological study.

PubMed

Wallach, Joshua D; Ciani, Oriana; Pease, Alison M; Gonsalves, Gregg S; Krumholz, Harlan M; Taylor, Rod S; Ross, Joseph S

2018-03-21

The U.S. Food and Drug Administration (FDA) often approves new drugs based on trials that use surrogate markers for endpoints, which involve certain trade-offs and may risk making erroneous inferences about the medical product's actual clinical effect. This study aims to compare the treatment effects among pivotal trials supporting FDA approval of novel therapeutics based on surrogate markers of disease with those observed among postapproval trials for the same indication. We searched Drugs@FDA and PubMed to identify published randomized superiority design pivotal trials for all novel drugs initially approved by the FDA between 2005 and 2012 based on surrogate markers as primary endpoints and published postapproval trials using the same surrogate markers or patient-relevant outcomes as endpoints. Summary ratio of odds ratios (RORs) and difference between standardized mean differences (dSMDs) were used to quantify the average difference in treatment effects between pivotal and matched postapproval trials. Between 2005 and 2012, the FDA approved 88 novel drugs for 90 indications based on one or multiple pivotal trials using surrogate markers of disease. Of these, 27 novel drugs for 27 indications were approved based on pivotal trials using surrogate markers as primary endpoints that could be matched to at least one postapproval trial, for a total of 43 matches. For nine (75.0%) of the 12 matches using the same non-continuous surrogate markers as trial endpoints, pivotal trials had larger treatment effects than postapproval trials. On average, treatment effects were 50% higher (more beneficial) in the pivotal than the postapproval trials (ROR 1.5; 95% confidence interval CI 1.01-2.23). For 17 (54.8%) of the 31 matches using the same continuous surrogate markers as trial endpoints, pivotal trials had larger treatment effects than the postapproval trials. On average, there was no difference in treatment effects between pivotal and postapproval trials (dSMDs 0.01; 95% CI -0.15-0.16). Many postapproval drug trials are not directly comparable to previously published pivotal trials, particularly with respect to endpoint selection. Although treatment effects from pivotal trials supporting FDA approval of novel therapeutics based on non-continuous surrogate markers of disease are often larger than those observed among postapproval trials using surrogate markers as trial endpoints, there is no evidence of difference between pivotal and postapproval trials using continuous surrogate markers.

The influence of applied internal and external rotation on the pivot shift phenomenon.

PubMed

Kopf, Sebastian; Musahl, Volker; Perka, Carsten; Kauert, Ralf; Hoburg, Arnd; Becker, Roland

2017-04-01

The pivot shift test is performed in different techniques and the rotation of the tibia seems to have a significant impact on the amount of the pivot shift phenomenon. It has been hypothesised that external rotation will increase the phenomenon due to less tension at the iliotibial band in knee extension. Twenty-four patients with unilateral anterior cruciate ligament insufficiency were included prospectively. The pivot shift test was performed bilaterally in internal and external tibial rotation under general anaesthesia. Knee motion was captured using a femoral and a tibial inertial sensor. The difference between positive and negative peak values in Euclidean norm of acceleration was calculated to evaluate the amount of the pivot shift phenomenon. The pivot shift phenomenon was significantly increased in patients with ACL insufficiency when the test was performed in external [mean 5.2 ms - 2 (95% CI 4.3-6.0)] compared to internal tibial rotation [mean 4.4 ms - 2 (95% CI 3.5-5.4)] (p = 0.002). In healthy, contralateral knees did not show any difference between external [mean 4.0 ms - 2 (95% CI 3.3-4.7)] and internal tibial rotation [mean 4.0 ms - 2 (95% CI 3.4-4.6)] (ns). The pivot shift phenomenon was increased with external rotation in ACL-insufficient knees, and therefore, one should perform the pivot shift test, rather, in external rotation to easily evoke the, sometimes difficult to detect, pivot shift phenomenon. I (diagnostic study).

How long bones grow children: Mechanistic paths to variation in human height growth.

PubMed

Lampl, Michelle; Schoen, Meriah

2017-03-01

Eveleth and Tanner's descriptive documentation of worldwide variability in human growth provided evidence of the interaction between genetics and environment during development that has been foundational to the science of human growth. There remains a need, however, to describe the mechanistic foundations of variability in human height growth patterns. A review of research documenting cellular activities at the endochondral growth plate aims to show how the unique microenvironment and cell functions during the sequential phases of the chondrocyte lifecycle affect long bone elongation, a fundamental source of height growth. There are critical junctures within the chondrocytic differentiation cascade at which environmental influences are integrated and have the ability to influence progression to the hypertrophic chondrocyte phase, the primary driver of long bone elongation. Phenotypic differences in height growth patterns reflect variability in amplitude and frequency of discretely timed hypertrophic cellular expansion events, the cellular basis of saltation and stasis growth biology. Final height is a summary of the dynamic processes carried out by the growth plate cellular machinery. As these cell-level mechanisms unfold in an individual, time-specific manner, there are many critical points at which a genetic growth program can be enhanced or perturbed. Recognizing both the complexity and fluidity of this adaptive system questions the likelihood of a single, optimal growth pattern and instead identifies a larger bandwidth of saltatory frequencies for "normal" growth. Further inquiry into mechanistic sources of variability acting at critical organizational points of chondrogenesis can provide new opportunities for growth interventions. © 2017 Wiley Periodicals, Inc.

Failure Analysis on Tail Rotor Teeter Pivot Bolt on a Helicopter

NASA Astrophysics Data System (ADS)

Qiang, WANG; Zi-long, DONG

2018-03-01

Tail rotor teeter pivot bolt of a helicopter fractured when in one flight. Failure analysis on the bolt was finished in laboratory. Macroscopic observation of the tailor rotor teeter pivot bolt, macro and microscopic inspection on the fracture surface of the bolt was carried out. Chemical components and metallurgical structure was also carried out. Experiment results showed that fracture mode of the tail rotor teeter pivot bolt is fatigue fracture. Fatigue area is over 80% of the total fracture surface, obvious fatigue band characteristics can be found at the fracture face. According to the results were analyzed from the macroscopic and microcosmic aspects, fracture reasons of the tail rotor teeter pivot bolt were analyzed in detail

A Comparative Study of Precise Point Positioning (PPP) Accuracy Using Online Services

NASA Astrophysics Data System (ADS)

Malinowski, Marcin; Kwiecień, Janusz

2016-12-01

Precise Point Positioning (PPP) is a technique used to determine the position of receiver antenna without communication with the reference station. It may be an alternative solution to differential measurements, where maintaining a connection with a single RTK station or a regional network of reference stations RTN is necessary. This situation is especially common in areas with poorly developed infrastructure of ground stations. A lot of research conducted so far on the use of the PPP technique has been concerned about the development of entire day observation sessions. However, this paper presents the results of a comparative analysis of accuracy of absolute determination of position from observations which last between 1 to 7 hours with the use of four permanent services which execute calculations with PPP technique such as: Automatic Precise Positioning Service (APPS), Canadian Spatial Reference System Precise Point Positioning (CSRS-PPP), GNSS Analysis and Positioning Software (GAPS) and magicPPP - Precise Point Positioning Solution (magicGNSS). On the basis of acquired results of measurements, it can be concluded that at least two-hour long measurements allow acquiring an absolute position with an accuracy of 2-4 cm. An evaluation of the impact on the accuracy of simultaneous positioning of three points test network on the change of the horizontal distance and the relative height difference between measured triangle vertices was also conducted. Distances and relative height differences between points of the triangular test network measured with a laser station Leica TDRA6000 were adopted as references. The analyses of results show that at least two hours long measurement sessions can be used to determine the horizontal distance or the difference in height with an accuracy of 1-2 cm. Rapid products employed in calculations conducted with PPP technique reached the accuracy of determining coordinates on a close level as in elaborations which employ Final products.

Water level effects on breaking wave setup for Pacific Island fringing reefs

NASA Astrophysics Data System (ADS)

Becker, J. M.; Merrifield, M. A.; Ford, M.

2014-02-01

The effects of water level variations on breaking wave setup over fringing reefs are assessed using field measurements obtained at three study sites in the Republic of the Marshall Islands and the Mariana Islands in the western tropical Pacific Ocean. At each site, reef flat setup varies over the tidal range with weaker setup at high tide and stronger setup at low tide for a given incident wave height. The observed water level dependence is interpreted in the context of radiation stress gradients specified by an idealized point break model generalized for nonnormally incident waves. The tidally varying setup is due in part to depth-limited wave heights on the reef flat, as anticipated from previous reef studies, but also to tidally dependent breaking on the reef face. The tidal dependence of the breaking is interpreted in the context of the point break model in terms of a tidally varying wave height to water depth ratio at breaking. Implications for predictions of wave-driven setup at reef-fringed island shorelines are discussed.

Non-musicians also have a piano in the head: evidence for spatial-musical associations from line bisection tracking.

PubMed

Hartmann, Matthias

2017-02-01

The spatial representation of ordinal sequences (numbers, time, tones) seems to be a fundamental cognitive property. While an automatic association between horizontal space and pitch height (left-low pitch, right-high pitch) is constantly reported in musicians, the evidence for such an association in non-musicians is mixed. In this study, 20 non-musicians performed a line bisection task while listening to irrelevant high- and low-pitched tones and white noise (control condition). While pitch height had no influence on the final bisection point, participants' movement trajectories showed systematic biases: When approaching the line and touching the line for the first time (initial bisection point), the mouse cursor was directed more rightward for high-pitched tones compared to low-pitched tones and noise. These results show that non-musicians also have a subtle but nevertheless automatic association between pitch height and the horizontal space. This suggests that spatial-musical associations do not necessarily depend on constant sensorimotor experiences (as it is the case for musicians) but rather reflect the seemingly inescapable tendency to represent ordinal information on a horizontal line.

Geometric Accuracy Analysis of Worlddem in Relation to AW3D30, Srtm and Aster GDEM2

NASA Astrophysics Data System (ADS)

Bayburt, S.; Kurtak, A. B.; Büyüksalih, G.; Jacobsen, K.

2017-05-01

In a project area close to Istanbul the quality of WorldDEM, AW3D30, SRTM DSM and ASTER GDEM2 have been analyzed in relation to a reference aerial LiDAR DEM and to each other. The random and the systematic height errors have been separated. The absolute offset for all height models in X, Y and Z is within the expectation. The shifts have been respected in advance for a satisfying estimation of the random error component. All height models are influenced by some tilts, different in size. In addition systematic deformations can be seen not influencing the standard deviation too much. The delivery of WorldDEM includes information about the height error map which is based on the interferometric phase errors, and the number and location of coverage's from different orbits. A dependency of the height accuracy from the height error map information and the number of coverage's can be seen, but it is smaller as expected. WorldDEM is more accurate as the other investigated height models and with 10 m point spacing it includes more morphologic details, visible at contour lines. The morphologic details are close to the details based on the LiDAR digital surface model (DSM). As usual a dependency of the accuracy from the terrain slope can be seen. In forest areas the canopy definition of InSAR X- and C-band height models as well as for the height models based on optical satellite images is not the same as the height definition by LiDAR. In addition the interferometric phase uncertainty over forest areas is larger. Both effects lead to lower height accuracy in forest areas, also visible in the height error map.

Mechanical design of deformation compensated flexural pivots structured for linear nanopositioning stages

DOEpatents

Shu, Deming; Kearney, Steven P.; Preissner, Curt A.

2015-02-17

A method and deformation compensated flexural pivots structured for precision linear nanopositioning stages are provided. A deformation-compensated flexural linear guiding mechanism includes a basic parallel mechanism including a U-shaped member and a pair of parallel bars linked to respective pairs of I-link bars and each of the I-bars coupled by a respective pair of flexural pivots. The basic parallel mechanism includes substantially evenly distributed flexural pivots minimizing center shift dynamic errors.

Carbon Sequestration Estimation of Street Trees Based on Point Cloud from Vehicle-Borne Laser Scanning System

NASA Astrophysics Data System (ADS)

Zhao, Y.; Hu, Q.

2017-09-01

Continuous development of urban road traffic system requests higher standards of road ecological environment. Ecological benefits of street trees are getting more attention. Carbon sequestration of street trees refers to the carbon stocks of street trees, which can be a measurement for ecological benefits of street trees. Estimating carbon sequestration in a traditional way is costly and inefficient. In order to solve above problems, a carbon sequestration estimation approach for street trees based on 3D point cloud from vehicle-borne laser scanning system is proposed in this paper. The method can measure the geometric parameters of a street tree, including tree height, crown width, diameter at breast height (DBH), by processing and analyzing point cloud data of an individual tree. Four Chinese scholartree trees and four camphor trees are selected for experiment. The root mean square error (RMSE) of tree height is 0.11m for Chinese scholartree and 0.02m for camphor. Crown widths in X direction and Y direction, as well as the average crown width are calculated. And the RMSE of average crown width is 0.22m for Chinese scholartree and 0.10m for camphor. The last calculated parameter is DBH, the RMSE of DBH is 0.5cm for both Chinese scholartree and camphor. Combining the measured geometric parameters and an appropriate carbon sequestration calculation model, the individual tree's carbon sequestration will be estimated. The proposed method can help enlarge application range of vehicle-borne laser point cloud data, improve the efficiency of estimating carbon sequestration, construct urban ecological environment and manage landscape.

Radiographic comparison of different concentrations of recombinant human bone morphogenetic protein with allogenic bone compared with the use of 100% mineralized cancellous bone allograft in maxillary sinus grafting.

PubMed

Froum, Stuart J; Wallace, Stephen; Cho, Sang-Choon; Khouly, Ismael; Rosenberg, Edwin; Corby, Patricia; Froum, Scott; Mascarenhas, Patrick; Tarnow, Dennis P

2014-01-01

The purpose of this study was to radiographically evaluate, then analyze, bone height, volume, and density with reference to percentage of vital bone after maxillary sinuses were grafted using two different doses of recombinant human bone morphogenetic protein 2/acellular collagen sponge (rhBMP-2/ACS) combined with mineralized cancellous bone allograft (MCBA) and a control sinus grafted with MCBA only. A total of 18 patients (36 sinuses) were used for analysis of height and volume measurements, having two of three graft combinations (one in each sinus): (1) control, MCBA only; (2) test 1, MCBA + 5.6 mL of rhBMP-2/ACS (containing 8.4 mg of rhBMP-2); and (3) test 2, MCBA + 2.8 mL of rhBMP-2/ACS (containing 4.2 mg of rhBMP-2). The study was completed with 16 patients who also had bilateral cores removed 6 to 9 months following sinus augmentation. A computer software system was used to evaluate 36 computed tomography scans. Two time points where selected for measurements of height: The results indicated that height of the grafted sinus was significantly greater in the treatment groups compared with the control. However, by the second time point, there were no statistically significant differences. Three weeks post-surgery bone volume measurements showed similar statistically significant differences between test and controls. However, prior to core removal, test group 1 with the greater dose of rhBMP-2 showed a statistically significant greater increase compared with test group 2 and the control. There was no statistically significant difference between the latter two groups. All three groups had similar volume and shrinkage. Density measurements varied from the above results, with the control showing statistically significant greater density at both time points. By contrast, the density increase over time in both rhBMP groups was similar and statistically higher than in the control group. There were strong associations between height and volume in all groups and between volume and new vital bone only in the control group. There were no statistically significant relationships observed between height and bone density or between volume and bone density for any parameter measured. More cases and monitoring of the future survival of implants placed in these augmented sinuses are needed to verify these results.

Cutting assembly

DOEpatents

Racki, Daniel J.; Swenson, Clark E.; Bencloski, William A.; Wineman, Arthur L.

1984-01-01

A cutting apparatus includes a support table mounted for movement toward and away from a workpiece and carrying a mirror which directs a cutting laser beam onto the workpiece. A carrier is rotatably and pivotally mounted on the support table between the mirror and workpiece and supports a conduit discharging gas toward the point of impingement of the laser beam on the workpiece. Means are provided for rotating the carrier relative to the support table to place the gas discharging conduit in the proper positions for cuts made in different directions on the workpiece.

Earth observations during Space Shuttle flight STS-29 - Discovery's voyage to the earth

NASA Technical Reports Server (NTRS)

Lulla, Kamlesh; Helfert, Michael; Whitehead, Victor; Amsbury, David; Coats, Michael; Blaha, John; Buchli, James; Springer, Robert; Bagian, James

1989-01-01

The environmental, geologic, meteorologic, and oceanographic phenomena documented by earth photography during the Space Shuttle STS-29 mission are reviewed. A map of the nadir point positions of earth-viewing photographs from the mission is given and color photographs of various regions are presented. The mission photographs include atmospheric dust and smoke over parts of Africa and Asia, Sahelian water sites, center pivot irrigation fields in the Middle East, urban smog over Mexico City, isolated burning in the Bolivian Amazon, and various ocean features and cloud formations.

The Geoscience Laser Altimeter System (GLAS) for the ICESAT Mission

NASA Technical Reports Server (NTRS)

Abshire, James B.; Sun, Xia-Li; Ketchum, Eleanor A.; Afzal, Robert S.; Millar, Pamela S.; Smith, David E. (Technical Monitor)

2000-01-01

The Laser In space Technology Experiment, Shuttle Laser Altimeter and the Mars Observer Laser Altimeter have demonstrated accurate measurements of atmospheric backscatter and Surface heights from space. The recent MOLA measurements of the Mars surface have 40 cm vertical resolution and have reduced the global uncertainty in Mars topography from a few km to about 5 m. The Geoscience Laser Altimeter System (GLAS) is a next generation lidar for Earth orbit being developed as part of NASA's Icesat Mission. The GLAS design combines a 10 cm precision surface lidar with a sensitive dual wavelength cloud and aerosol lidar. GLAS will precisely measure the heights of the Earth's polar ice sheets, establish a grid of accurate height profiles of the Earth's land topography, and profile the vertical backscatter of clouds and aerosols on a global scale. GLAS is being developed to fly on a small dedicated spacecraft in a polar orbit with a 590 630 km altitude at inclination of 94 degrees. GLAS is scheduled to launch in the summer 2001 and to operate continuously for a minimum of 3 years with a goal of 5 years. The primary mission for GLAS is to measure the seasonal and annual changes in the heights of the Greenland and Antarctic ice sheets. GLAS will continuously measure the vertical distance from orbit to the Earth's surface with 1064 nm pulses from a ND:YAG laser at a 40 Hz rate. Each 5 nsec wide laser pulse is used to produce a single range measurement, and the laser spots have 66 m diameter and about 170 m center-center spacings. When over land GLAS will profile the heights of the topography and vegetation. The GLAS receiver uses a 1 m diameter telescope and a Si APD detector. The detector signal is sampled by an all digital receiver which records each surface echo waveform with I nsec resolution and a stored echo record lengths of either 200, 400, or 600 samples. Analysis of the echo waveforms within the instrument permits discrimination between cloud and surface echoes. Ground based echo analysis permits precise ranging, determining the roughness or slopes of the surface as well as the vertical distributions of vegetation illuminated by the laser. Accurate knowledge of the laser beam's pointing angle is needed to prevent height biases when over sloped surfaces. For surfaces with 2 deg. slopes, knowledge of pointing angle of the beam's centroid to about 8 urad is needed to achieve 10 cm height accuracy. GLAS uses a stellar reference system (SRS) to determine the pointing angle of each laser firing relative to inertial space. The SRS uses a high precision star camera oriented toward local zenith and a gyroscope to determine the inertial orientation of the SRS optical bench. The far field pattern of each laser is measured pulse relative to the star camera with a laser reference system (LRS). Optically measuring each laser far field pattern relative to the orientation of the star camera and gyroscope permits the precise pointing angle of each laser pulse to be determined. GLAS will also determine the vertical distributions of clouds and aerosols by measuring the vertical profile of laser energy backscattered by the atmosphere at both 1064 and 532 nm. The 1064 nm measurements use the Si APD detector and profile the height and vertical structure of thicker clouds. The measurements at 532 nm use new highly sensitive photon counting, detectors, and measure the height distributions of very thin Clouds and aerosol layers. With averaging these can be used to determine the height of the planetary boundary layer. The instrument design and expected performance will be discussed.

SRTM 3" comparison with local information: Two examples at national level in Peru

NASA Astrophysics Data System (ADS)

Plasencia Sánchez, Edson; Fernandez de Villarán, Ruben

2012-06-01

The access to the high resolution digital terrain models (DEM) generated from the data collected by the Shuttle Radar Topography Mission (SRTM) of NASA is freely available to the public. Consequently it has become a source of topographic information which is of great value to scientists involved in geophysical or geodetic analysis. Despite the efforts of the Consultative Group on International Agricultural Research (CGIAR), to validate and complement the information contained in these DEMs (currently offered as version 4.1), they still need to be checked for their accuracy in certain regions of the planet. In this paper, the vertical accuracy of the SRTM 3" version 4.1 DEM was analyzed in several areas of Peru using two sets of control points: the height of the district capitals (the minor politics units) and the heights of the weather and hydrological stations from the National Meteorology and Hydrology Service (SENAMHI) of Peru. The comparison shows that the height differences are independent of the altitude, latitude and longitude of the evaluated points. They are rather related to the aspect of the terrain and to the way the SRTM data were acquired. It shows that the mean square of the height differences at national level was ±20 m for district capitals and ±25 m for the SENAMHI stations. This is slightly larger than the overall accuracy of the SRTM ±16 m.

Indentation measurements on the eardrum with automated projection moiré profilometry

NASA Astrophysics Data System (ADS)

Buytaert, J. A. N.; Aernouts, J. E. F.; Dirckx, J. J. J.

2009-03-01

Computer modeling of middle ear mechanics is an important tool to investigate its complex behavior, but correct mechanical and elastic parameters are needed to obtain realistic simulations. A possible way to determine eardrum elasticity in situ is the use of point indentation measurements. The eardrum is, however, a small fragile membrane, so a non-contacting high-resolution technique is needed to measure the shape change caused by point indentation. We have developed a projection moiré interferometer combined with an indentation actuator and a high-resolution force sensor. The apparatus applies deformations up to 1 mm with a resolution of 1 μm, while the indentation force is measured with a resolution better than 1 mN. The moiré setup delivers height data on 512×512 points through phase-shifting, with a height resolution of 15 μm. Shape recordings are made on a rabbit eardrum at different indentation distances, and indentation force is recorded simultaneously.

Automatic co-registration of 3D multi-sensor point clouds

NASA Astrophysics Data System (ADS)

Persad, Ravi Ancil; Armenakis, Costas

2017-08-01

We propose an approach for the automatic coarse alignment of 3D point clouds which have been acquired from various platforms. The method is based on 2D keypoint matching performed on height map images of the point clouds. Initially, a multi-scale wavelet keypoint detector is applied, followed by adaptive non-maxima suppression. A scale, rotation and translation-invariant descriptor is then computed for all keypoints. The descriptor is built using the log-polar mapping of Gabor filter derivatives in combination with the so-called Rapid Transform. In the final step, source and target height map keypoint correspondences are determined using a bi-directional nearest neighbour similarity check, together with a threshold-free modified-RANSAC. Experiments with urban and non-urban scenes are presented and results show scale errors ranging from 0.01 to 0.03, 3D rotation errors in the order of 0.2° to 0.3° and 3D translation errors from 0.09 m to 1.1 m.

High Reynolds number rough wall turbulent boundary layer experiments using Braille surfaces

NASA Astrophysics Data System (ADS)

Harris, Michael; Monty, Jason; Nova, Todd; Allen, James; Chong, Min

2007-11-01

This paper details smooth, transitional and fully rough turbulent boundary layer experiments in the New Mexico State high Reynolds number rough wall wind tunnel. The initial surface tested was generated with a Braille printer and consisted of an uniform array of Braille points. The average point height being 0.5mm, the spacing between the points in the span was 0.5mm and the surface consisted of span wise rows separated by 4mm. The wavelength to peak ratio was 8:1. The boundary layer thickness at the measurement location was 190mm giving a large separation of roughness height to layer thickness. The maximum friction velocity was uτ=1.5m/s at Rex=3.8 x10^7. Results for the skin friction co-efficient show that this surface follows a Nikuradse type inflectional curve and that Townsends outer layer similarity hypothesis is valid for rough wall flows with a large separation of scales. Mean flow and turbulence statistics will be presented.

Child pedestrian anthropometry: evaluation of potential impact points during a crash.

PubMed

Serre, Thierry; Lalys, Loïc; Bartoli, Christophe; Christia-Lotter, Amandine; Leonetti, Georges; Brunet, Christian

2010-11-01

This paper highlights the potential impact points of a child pedestrian during a crash with the front end of a vehicle. Child anthropometry was defined for ages between 3 and 15 years. It was based on the measurement of seven different segment body heights (knee, femur, pelvis, shoulder, neck, chin, vertex) performed on about 2,000 French children. For each dimension, the 5(th), 50(th) and 95(th) percentile values were reported, and the corresponding linear regression lines were given. Then these heights were confronted with three different vehicle shapes, corresponding to a passenger car, a sport utility vehicle and a light truck, to identify impact points. In particular, we show that the thigh is directly hit by the bumper for children above 12 years of age, whereas the head principally impacts the hood. The influence of child anthropometry on the pedestrian trajectory and the comparison with test procedures in regulation are discussed. 2010 Elsevier Ltd. All rights reserved.

Pivotal Response Training. What Works Clearinghouse Intervention Report

ERIC Educational Resources Information Center

What Works Clearinghouse, 2016

2016-01-01

This intervention report presents findings from a systematic review of "pivotal response training" conducted using the What Works Clearinghouse Procedures and Standards Handbook (version 3.0) and the Children and Students with an Autism Spectrum Disorder review protocol (version 3.0). "Pivotal response training"…

A climatology of extreme wave height events impacting eastern Lake Ontario shorelines

NASA Astrophysics Data System (ADS)

Grieco, Matthew B.; DeGaetano, Arthur T.

2018-05-01

Model-derived wave height data for points along the eastern Lake Ontario shoreline provide the basis for a 36-year climatology of extreme wave heights. The most extreme wave heights exceed 6 m at all locations, except for those along the extreme northeastern shoreline of the Lake. Typically extreme wave events are a regional phenomenon, affecting multiple locations along the eastern and southeastern shoreline. A pronounced seasonal cycle in wave event occurrence is characterized by peaks in autumn and spring, with an absence of 99.9th percentile wave heights during summer. Less extreme (90th percentile heights) occur in all months with a peak in winter. Extreme wave events are most often associated with a low pressure center tracking to the north of Lake Ontario from the Ohio Valley. This track produces the strong winds > 10 ms-1 and predominantly west-to-east wind fetch that characterize high wave height events. The seasonal frequency of the wave events exceeding the historical 95th percentile has shown a statistically significant increase at most locations since 1979. This has been partially offset by declines in the frequency of events with wave heights between the 90 and 95th percentile. Seasonal extreme wave height frequency is also found to be related to the occurrence of El Niño. During El Niño winters, there are significantly fewer events with wave heights exceeding 2.5 m than would be expected by chance. A corresponding relationship to La Niña occurrence is not evident.

The Efficiency of Small Bearings in Instruments of the Type Used in Aircraft

NASA Technical Reports Server (NTRS)

Norton, F H

1921-01-01

This report deals with the construction and properties of bearings and pivots for use in instruments. The static and running friction for both thrust and radial loads was determined for a number of conical pivots and cylindrical and ball bearings. The static rocking friction was also measured for several conical and ball bearings under a heavy load, especially to determine their suitability for use in N. P. L. (National Physical Laboratory) type wind tunnel balance. In constructing conical pivots and sockets it was found that the pivots should be hardened and highly polished, preferably with a revolving lap, and that the sockets should be made by punching with a hardened and polished punch. It was found that for a light load the conical pivots give less friction than any other type, and their wearing qualities when hardened are excellent. Very small ball bearings are unsatisfactory because the proportional accuracy of the balls and races is not high enough to insure smooth running. For rocking pivots under heavy loads it was found that a ball-and-socket bearing, consisting of a hemispherical socket and a sphere of smaller diameter concentric with it, with a row of small balls resting between the two, was superior to a pivot resting in a socket. It was found that vibration such as occurs in an airplane will greatly reduce the static friction of a pivot or bearing, in some cases to as little as one-twentieth of its static value.

Dimensions of the scala tympani in the human and cat with reference to cochlear implants.

PubMed

Hatsushika, S; Shepherd, R K; Tong, Y C; Clark, G M; Funasaka, S

1990-11-01

The width, height, and cross-sectional area of the scala tympani in both the human and cat were measured to provide dimensional information relevant to the design of scala tympani electrode arrays. Both the height and width of the human scala tympani decreased rapidly within the first 1.5 mm from the round window. Thereafter, they exhibit a gradual reduction in their dimension with increasing distance from the round window. The cross-sectional area of the human scala tympani reflects the changes observed in both the height and width. In contrast, the cat scala tympani exhibits a rapid decrease in its dimensions over the first 6 to 8 mm from the round window. However, beyond this point the cat scala tympani also exhibits a more gradual decrease in its dimensions. Finally, the width of the scala tympani, in both human and cat, is consistently greater than the height.

Urbanization Causes Increased Cloud Base Height and Decreased Fog in Coastal Southern California

NASA Technical Reports Server (NTRS)

Williams, A. Park; Schwartz, Rachel E.; Iacobellis, Sam; Seager, Richard; Cook, Benjamin I.; Still, Christopher J.; Husak, Gregory; Michaelsen, Joel

2015-01-01

Subtropical marine stratus clouds regulate coastal and global climate, but future trends in these clouds are uncertain. In coastal Southern California (CSCA), interannual variations in summer stratus cloud occurrence are spatially coherent across 24 airfields and dictated by positive relationships with stability above the marine boundary layer (MBL) and MBL height. Trends, however, have been spatially variable since records began in the mid-1900s due to differences in nighttime warming. Among CSCA airfields, differences in nighttime warming, but not daytime warming, are strongly and positively related to fraction of nearby urban cover, consistent with an urban heat island effect. Nighttime warming raises the near-surface dew point depression, which lifts the altitude of condensation and cloud base height, thereby reducing fog frequency. Continued urban warming, rising cloud base heights, and associated effects on energy and water balance would profoundly impact ecological and human systems in highly populated and ecologically diverse CSCA.

Controlling the ripple density and heights: a new way to improve the electrical performance of CVD-grown graphene.

PubMed

Park, Won-Hwa; Jo, Insu; Hong, Byung Hee; Cheong, Hyeonsik

2016-05-14

We report a new way to enhance the electrical performances of large area CVD-grown graphene through controlling the ripple density and heights after transfer onto SiO2/Si substrates by employing different cooling rates during fabrication. We find that graphene films prepared with a high cooling rate have reduced ripple density and heights and improved electrical characteristics such as higher electron/hole mobilities as well as reduced sheet resistance. The corresponding Raman analysis also shows a significant decrease of the defects when a higher cooling rate is employed. We suggest a model that explains the improved morphology of the graphene film obtained with higher cooling rates. From these points of view, we can suggest a new pathway toward a relatively lower density and heights of ripples in order to reduce the flexural phonon-electron scattering effect, leading to higher lateral carrier mobilities.

Characteristics of offshore extreme wind-waves detected by surface drifters with a low-cost GPS wave sensor

NASA Astrophysics Data System (ADS)

Komatsu, Kosei

Wind-generated waves have been recognized as one of the most important factors of the sea surface roughness which plays crucial roles in various air-sea interactions such as energy, mo-mentum, heat and gas exchanges. At the same time, wind waves with extreme wave heights representatively called as freak or rogue waves have been a matter of great concern for many people involved in shipping, fishing, constracting, surfing and other marine activities, because such extreme waves frequently affect on the marine activities and sometimes cause serious dis-asters. Nevertheless, investigations of actual conditions for the evolution of wind waves in the offshore region are less and sparse in contrast to dense monitoring networks in the coastal re-gions because of difficulty of offshore observation with high accuracy. Recently accurate in situ observation of offshore wind waves is getting possible at low cost owing to a wave height and di-rection sensor developed by Harigae et al. (2004) by installing a point-positioning GPS receiver on a surface drifting buoy. The point-positioning GPS sensor can extract three dimensional movements of the buoy excited by ocean waves with minimizing effects of GPS point-positioning errors through the use of a high-pass filter. Two drifting buoys equipped with the GPS-based wave sensor charged by solar cells were drifted in the western North Pacific and one of them continued to observe wind waves during 16 months from Sep. 2007. The RMSE of the GPS-based wave sensor was less than 10cm in significant wave height and about 1s in significant wave period in comparison with other sensors, i.e. accelerometers installed on drifting buoys of Japan Meteorological Agency, ultrasonic sensors placed at the Hiratsuka observation station of the University of Tokyo and altimeter of the JASON-1. The GPS-based wave buoys enabled us to detect freak waves defined as waves whose height is more than twice the significant wave height. The observation conducted by the wave buoys in 2007-2008 indicated a little more frequent occurrence of freak waves comparing with Forristall's (1978) empirical formula and Naess's (1985) distribution for a narrow-band Gaussian sea.

Classroom furniture and anthropometric characteristics of Iranian high school students: proposed dimensions based on anthropometric data.

PubMed

Dianat, Iman; Karimi, Mohammad Ali; Asl Hashemi, Ahmad; Bahrampour, Samira

2013-01-01

The study evaluated the potential mismatch between classroom furniture dimensions and anthropometric characteristics of 978 Iranian high school students (498 girls, 480 boys), aged 15-18 years. Nine anthropometric measurements (stature, sitting height, sitting shoulder height, popliteal height, hip breadth, elbow-seat height, buttock-popliteal length, buttock-knee length and thigh clearance) and five dimensions from the existing classroom furniture were measured and then compared together (using match criterion equations) to identify any potential mismatch between them. The results indicated a considerable mismatch between body dimensions of the students and the existing classroom furniture, with seat height (60.9%), seat width (54.7%) and desktop height (51.7%) being the furniture dimensions with a higher level of mismatch. The levels of mismatch varied between the high-school grade levels and between genders, indicating their special requirements and possible problems. The proposed dimensions of the classroom furniture more appropriate for the students were given. This additional information on students' anthropometry can be used by local furniture industries as a starting point for designing more appropriate furniture for school children, or used by schools to aid in furniture selection. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Validity of the Jump-and-Reach Test in Subelite Adolescent Handball Players.

PubMed

Muehlbauer, Thomas; Pabst, Jan; Granacher, Urs; Büsch, Dirk

2017-05-01

Muehlbauer, T, Pabst, J, Granacher, U, and Büsch, D. Validity of the jump-and-reach test in subelite adolescent handball players. J Strength Cond Res 31(5): 1282-1289, 2017-The primary purpose of this study was to examine concurrent validity of the jump-and-reach (JaR) test using the Vertec system and a criterion device (i.e., Optojump system). In separate subanalyses, we investigated the influence of gym floor condition and athletes' sex on the validity of vertical jump height. Four hundred forty subelite adolescent female (n = 222, mean age: 14 ± 1 year, age range: 13-15 years) and male (n = 218, mean age: 15 ± 1 year, age range: 14-16 years) handball players performed the JaR test in gyms with region or point elastic floors. Maximal vertical jump height was simultaneously assessed using the Vertec and the Optojump systems. In general, significantly higher jump heights were obtained for the Vertec compared with the Optojump system (11.2 cm, Δ31%, Cohen's d = 2.58). The subanalyses revealed significantly larger jump heights for the Vertec compared with the Optojump system irrespective of gym floor condition and players' sex. The association between Optojump- and Vertec-derived vertical jump heights amounted to rP = 0.84, with a coefficient of determination (R) of 0.71. The subanalyses indicated significantly larger correlations in males (rP = 0.75, R = 0.56) than in females (rP = 0.63, R = 0.40). Yet, correlations were not significantly different between region (rP = 0.83, R = 0.69) as opposed to point elastic floor (rP = 0.87, R = 0.76). Our findings indicate that the 2 apparatuses cannot be used interchangeably. Consequently, gym floor and sex-specific regression equations were provided to estimate true (Optojump system) vertical jump height from Vertec-derived data.

Effect of Coronary Anatomy and Hydrostatic Pressure on Intracoronary Indices of Stenosis Severity.

PubMed

Härle, Tobias; Luz, Mareike; Meyer, Sven; Kronberg, Kay; Nickau, Britta; Escaned, Javier; Davies, Justin; Elsässer, Albrecht

2017-04-24

The authors sought to analyze height differences within the coronary artery tree in patients in a supine position and to quantify the impact of hydrostatic pressure on intracoronary pressure measurements in vitro. Although pressure equalization of the pressure sensor and the systemic pressure at the catheter tip is mandatory in intracoronary pressure measurements, subsequent measurements may be influenced by hydrostatic pressure related to the coronary anatomy in the supine position. Outlining and quantifying this phenomenon is important to interpret routine and pullback pressure measurements within the coronary tree. Coronary anatomy was analyzed in computed tomography angiographies of 70 patients to calculate height differences between the catheter tip and different coronary segments in the supine position. Using a dynamic pressure simulator, the effect of the expected hydrostatic pressure resulting from such height differences on indices stenosis severity was assessed. In all patients, the left anterior and right posterior descending arteries are the highest points of the coronary tree with a mean height difference of -4.9 ± 1.6 cm and -3.8 ± 1.0 cm; whereas the circumflex artery and right posterolateral branches are the lowest points, with mean height differences of 3.9 ± 0.9 cm and 2.6 ± 1.6 cm compared with the according ostium. In vitro measurements demonstrated a correlation of the absolute pressure differences with height differences (r = 0.993; p < 0.0001) and the slope was 0.77 mm Hg/cm. The Pd/Pa ratio and instantaneous wave-free ratio correlated also with the height difference (fractional flow reserve r = 0.98; p < 0.0001; instantaneous wave-free ratio r = 0.97; p < 0.0001), but both were influenced by the systemic pressure level. Hydrostatic pressure variations resulting from normal coronary anatomy in a supine position influence intracoronary pressure measurements and may affect their interpretation during stenosis severity assessment. Copyright © 2017 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

Comparison of Tsunami height Distributions of the 1960 and the 2010 Chilean Earthquakes on the Coasts of the Japanese Islands

NASA Astrophysics Data System (ADS)

Tsuji, Y.; Takahashi, T.; Imai, K.

2010-12-01

The tsunami of the Chilean Earthquake (Mw8.8) of February 27, 2010 was detected also on the coasts of the Japanese Islands about 23 hours after the occurrence of the main shock. It caused no human damage. There was slight house damage manly in Miyagi prefecture, south part of Sanriku coast; six and fifty one houses were flooded above and below the floor, respectively. It caused remarkable fishery loss of 75 Million US$ mainly due to breaking of cultivation rafts. The tsunami of the 1960 Chilean Earthquake(Mw9.5) also hit the Japanese coasts more severely. It caused more immense damage than the 2010 tsunami; 142 people were killed, 1,581 houses were entirely destroyed, and 1,256 houses were swept away. Most of damage occurred in the districts of Sanriku coast, where inundation heights exceeded six meters at several points. We made field survey along the Japanese coast, visited offices of fishermen’s cooperatives at over 300 fishery ports, gathered eyewitnesses counts, and obtained information of the inundation limit, arrival time, and building and fishery damage. On the basis of the information of inundation, we measured tsunami heights. We obtained data of tsunami height at more than two hundred points (Tsuji et al., 2010). The distributions of the two tsunamis of the 1960 and the 2010 Chilean earthquakes on the coasts along the Japanese Islands are shown as Fig. 1. The maximum height of 2.2 meters was recorded at Kesennuma City, Miyagi Prefecture. The heights of the 2010 tsunami were generally one third of those of the 1960 tsunami. An eminent peak appears at Sanriku coast commonly for both tsunamis. In addition smaller peaks also appear commonly at the coasts of the east part of Hokkaido, near the top of Boso peninsula, near the top of Izu Peninsula, the east coast of Kii Peninsula, Tokushima prefecture, eastern part of Shikoku, and near the Cape Ashizuri in western part of Shikoku. Fig. 1 Trace height distributions of the tsunamis of the 1960(red) and the 2010(blue) Chilean Earthquakes along the coasts of the Japanese Islands

Pivoting-Head Wrench

NASA Technical Reports Server (NTRS)

Bradley, Glen L.

1993-01-01

Wrench ends pivot so it can be used to loosen or tighten nuts or bolts in confined spaces. One end equipped with open-end socket; other end, with double-hexagon socket. Heads pivot on pins. Pins fit tightly so heads do not flop; friction on pins sufficient to hold heads in positions until rotated intentionally.

Disruption Neutral Point Experiment on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Granetz, R. S.; Nakamura, Y.

2000-10-01

Disruptions of single-null elongated plasmas generally result in loss of vertical position control, leading to a current quench occurring at the top or bottom of the machine, with all the attendant problems of halo and eddy currents flowing in divertor structures. On JT-60U, it has been found that if the plasma is operated with its magnetic axis at a particular height, called the neutral point, the initial vertical drift after a thermal quench is significantly slower than usual, and sometimes can even be arrested, thereby avoiding a current quench in the divertor region entirely. In an ongoing collaboration between MIT and JAERI, the neutral point concept is being tested in Alcator C-Mod, which has a significantly higher plasma elongation than JT-60U (1.65 vs 1.3). Calculations using TSC predict a neutral point at z~=+1 cm above the midplane (a=22 cm). The existence of a neutral point has now been experimentally confirmed, albeit at a height of z=+2.7 cm. The plasma has remained vertically stable for up to 9 ms after the disruption thermal quench, which in principle, is long enough for the PF control system to respond, if programmed appropriately. In addition, the physics of the neutral point stability on C-Mod appears to be somewhat different than that on JT-60U.

Cranial sutures and craniometric points detected on MRI.

PubMed

Cotton, François; Rozzi, Fernando Ramirez; Vallee, Bernard; Pachai, Chahin; Hermier, Marc; Guihard-Costa, Anne-Marie; Froment, Jean-Claude

2005-03-01

The main goal of the study was to determine on MRI the cranial sutures, the craniometric points and craniometric measurements, and to correlate these results with classical anthropometric measurements. For this purpose, we reviewed 150 cerebral MRI examinations considered as normal (Caucasian population aged 20-49 years). For each examination we individualized 11 craniometric landmarks (Glabella, Bregma, Lambda, Opisthocranion, Opisthion, Basion, Inion, Porion, Infra-orbital, Eurion) and three measurements. Measurements were also calculated independently on 498 dry crania (Microscribe 3-DX digitizer). To validate the MRI procedure, we measured four dry crania by MRI and with compass or digital caliper gauges. Cranial sutures always appeared without signal (black), whatever the MRI sequence used, and they are better visualized with a 5 mm slice thickness (compact bone overlapping). Slice dynamic analysis and multiplanar reformatting allowed the detection of all craniometric points, some of these being more difficult to detect than others (Porion, Infra-orbital). The measurements determined by these points were as follows: Vertex-Basion height=135.66+/-6.56 mm; Eurion-Eurion width=141.17+/-5.19 mm; Glabella-Opisthocranion length=181.94+/-6.40 mm. On the midline T1-weighted sagittal image, all median craniometric landmarks can be individualized and the Glabella-Opisthocranion length, Vertex-Basion height and parenchyma indices can be calculated. Craniometric points and measurements between these points can be estimated with a standard cerebral MRI examination, with results that are similar to anthropometric data.

Section-Based Tree Species Identification Using Airborne LIDAR Point Cloud

NASA Astrophysics Data System (ADS)

Yao, C.; Zhang, X.; Liu, H.

2017-09-01

The application of LiDAR data in forestry initially focused on mapping forest community, particularly and primarily intended for largescale forest management and planning. Then with the smaller footprint and higher sampling density LiDAR data available, detecting individual tree overstory, estimating crowns parameters and identifying tree species are demonstrated practicable. This paper proposes a section-based protocol of tree species identification taking palm tree as an example. Section-based method is to detect objects through certain profile among different direction, basically along X-axis or Y-axis. And this method improve the utilization of spatial information to generate accurate results. Firstly, separate the tree points from manmade-object points by decision-tree-based rules, and create Crown Height Mode (CHM) by subtracting the Digital Terrain Model (DTM) from the digital surface model (DSM). Then calculate and extract key points to locate individual trees, thus estimate specific tree parameters related to species information, such as crown height, crown radius, and cross point etc. Finally, with parameters we are able to identify certain tree species. Comparing to species information measured on ground, the portion correctly identified trees on all plots could reach up to 90.65 %. The identification result in this research demonstrate the ability to distinguish palm tree using LiDAR point cloud. Furthermore, with more prior knowledge, section-based method enable the process to classify trees into different classes.

A sustainable model for training teachers to use pivotal response training.

PubMed

Suhrheinrich, Jessica

2015-08-01

The increase in the rate of autism diagnoses has created a growing demand for teachers who are trained to use effective interventions. The train-the-trainer model, which involves training supervisors to train others, may be ideal for providing cost-effective training and ongoing support to teachers. Although research supports interventions, such as pivotal response training, as evidence-based, dissemination to school environments has been problematic. This study assessed the benefits of using the train-the-trainer model to disseminate pivotal response training to school settings. A multiple-baseline design was conducted across three training groups, each consisting of one school staff member (trainer), three special education teachers, and six students. Trainers conducted the teacher-training workshop with high adherence to training protocol and met mastery criteria in their ability to implement pivotal response training, assess implementation of pivotal response training, and provide feedback to teachers. Six of the nine teachers mastered all components of pivotal response training. The remaining three teachers implemented 89% of the pivotal response training components correctly. The majority of trainers and teachers maintained their abilities at follow-up. These results support the use of the train-the-trainer model as an effective method of disseminating evidence-based practices in school settings. © The Author(s) 2014.

Efficient Execution Methods of Pivoting for Bulk Extraction of Entity-Attribute-Value-Modeled Data

PubMed Central

Luo, Gang; Frey, Lewis J.

2017-01-01

Entity-attribute-value (EAV) tables are widely used to store data in electronic medical records and clinical study data management systems. Before they can be used by various analytical (e.g., data mining and machine learning) programs, EAV-modeled data usually must be transformed into conventional relational table format through pivot operations. This time-consuming and resource-intensive process is often performed repeatedly on a regular basis, e.g., to provide a daily refresh of the content in a clinical data warehouse. Thus, it would be beneficial to make pivot operations as efficient as possible. In this paper, we present three techniques for improving the efficiency of pivot operations: 1) filtering out EAV tuples related to unneeded clinical parameters early on; 2) supporting pivoting across multiple EAV tables; and 3) conducting multi-query optimization. We demonstrate the effectiveness of our techniques through implementation. We show that our optimized execution method of pivoting using these techniques significantly outperforms the current basic execution method of pivoting. Our techniques can be used to build a data extraction tool to simplify the specification of and improve the efficiency of extracting data from the EAV tables in electronic medical records and clinical study data management systems. PMID:25608318

PiVoT GPS Receiver

NASA Technical Reports Server (NTRS)

Wennersten, Miriam Dvorak; Banes, Anthony Vince; Boegner, Gregory J.; Dougherty, Lamar; Edwards, Bernard L.; Roman, Joseph; Bauer, Frank H. (Technical Monitor)

2001-01-01

NASA Goddard Space Flight Center has built an open architecture, 24 channel space flight GPS receiver. The CompactPCI PiVoT GPS receiver card is based on the Mitel/GEC Plessey Builder-2 board. PiVoT uses two Plessey 2021 correlators to allow tracking of up to 24 separate GPS SV's on unique channels. Its four front ends can support four independent antennas, making it a useful card for hosting GPS attitude determination algorithms. It has been built using space quality, radiation tolerant parts. The PiVoT card will track a weaker signal than the original Builder 2 board. It also hosts an improved clock oscillator. The PiVoT software is based on the original Plessey Builder 2 software ported to the Linux operating system. The software is POSIX complaint and can easily be converted to other POSIX operating systems. The software is open source to anyone with a licensing agreement with Plessey. Additional tasks can be added to the software to support GPS science experiments or attitude determination algorithms. The next generation PiVoT receiver will be a single radiation hardened CompactPCI card containing the microprocessor and the GPS receiver optimized for use above the GPS constellation. PiVoT was flown successfully on a balloon in July, 2001, for its first non-simulated flight.

Studying Maximum Plantar Stress per Insole Design Using Foot CT-Scan Images of Hyperelastic Soft Tissues

PubMed Central

Sarikhani, Ali; Motalebizadeh, Abbas; Kamali Doost Azad, Babak

2016-01-01

The insole shape and the resulting plantar stress distribution have a pivotal impact on overall health. In this paper, by Finite Element Method, maximum stress value and stress distribution of plantar were studied for different insoles designs, which are the flat surface and the custom-molded (conformal) surface. Moreover, insole thickness, heel's height, and different materials were used to minimize the maximum stress and achieve the most uniform stress distribution. The foot shape and its details used in this paper were imported from online CT-Scan images. Results show that the custom-molded insole reduced maximum stress 40% more than the flat surface insole. Upon increase of thickness in both insole types, stress distribution becomes more uniform and maximum stress value decreases up to 10%; however, increase of thickness becomes ineffective above a threshold of 1 cm. By increasing heel height (degree of insole), maximum stress moves from heel to toes and becomes more uniform. Therefore, this scenario is very helpful for control of stress in 0.2° to 0.4° degrees for custom-molded insole and over 1° for flat insole. By changing the material of the insole, the value of maximum stress remains nearly constant. The custom-molded (conformal) insole which has 0.5 to 1 cm thickness and 0.2° to 0.4° degrees is found to be the most compatible form for foot. PMID:27843284

Decision-making process of women carrying a BRCA1 or BRCA2 mutation who have chosen prophylactic mastectomy.

PubMed

McQuirter, Megan; Castiglia, Luisa Luciani; Loiselle, Carmen G; Wong, Nora

2010-05-01

To explore the decision-making process of women with a BRCA1 or BRCA2 gene mutation who have chosen to undergo prophylactic mastectomy. Cross-sectional, qualitative, descriptive design. Participants were recruited from an outpatient cancer prevention center in the oncology and medical genetics departments of a large university-affiliated hospital in Montreal, Quebec, Canada. 10 women carrying a BRCA1 or BRCA2 mutation; 8 previously had had a prophylactic mastectomy and 2 were scheduled for surgery at the time of study. Semistructured, in-depth interviews were conducted. Field notes were written and audiotapes were transcribed verbatim. The textual data were coded and analyzed. Decision-making process for prophylactic mastectomy. Two broad findings emerged. First, several intrapersonal and contextual factors interacted throughout the process to move women either closer to choosing a prophylactic mastectomy or further from the decision. Second, all women reported experiencing a "pivotal point," an emotionally charged event when the decision to have a prophylactic mastectomy became definitive. Pivotal points for patients included either receiving a positive result for a genetic mutation or a breast cancer diagnosis for herself or a family member in the context of positive mutation status. Decision making about prophylactic mastectomy was an affective and intuitive process incorporating contexts and their relations rather than a rational, straight-forward process of weighing pros and cons. Supportive interventions for women in this population should explicitly address the individual and the inter-relationships of contextual factors that shape decision making about prophylactic mastectomy while recognizing important affective components involved.

A serial qualitative interview study of infant feeding experiences: idealism meets realism

PubMed Central

Craig, Leone C A; Britten, Jane; McInnes, Rhona M

2012-01-01

Objective To investigate the infant feeding experiences of women and their significant others from pregnancy until 6 months after birth to establish what would make a difference. Design Qualitative serial interview study. Setting Two health boards in Scotland. Participants 72 of 541 invited pregnant women volunteered. 220 interviews approximately every 4 weeks with 36 women, 26 partners, eight maternal mothers, one sister and two health professionals took place. Results The overarching theme was a clash between overt or covert infant feeding idealism and the reality experienced. This is manifest as pivotal points where families perceive that the only solution that will restore family well-being is to stop breast feeding or introduce solids. Immediate family well-being is the overriding goal rather than theoretical longer term health benefits. Feeding education is perceived as unrealistic, overly technical and rules based which can undermine women's confidence. Unanimously families would prefer the balance to shift away from antenatal theory towards more help immediately after birth and at 3–4 months when solids are being considered. Family-orientated interactive discussions are valued above breastfeeding-centred checklist style encounters. Conclusions Adopting idealistic global policy goals like exclusive breast feeding until 6 months as individual goals for women is unhelpful. More achievable incremental goals are recommended. Using a proactive family-centred narrative approach to feeding care might enable pivotal points to be anticipated and resolved. More attention to the diverse values, meanings and emotions around infant feeding within families could help to reconcile health ideals with reality. PMID:22422915

The Geoscience Laser Altimeter System (GLAS) for the ICESAT Mission

NASA Technical Reports Server (NTRS)

Abshire, James B.; Sun, Xiao-Li; Ketchum, Eleanor A.; Afzal, Robert S.; Millar, Pamela S.

1999-01-01

Accurate measurements of surface heights and atmospheric backscatter have been demonstrated with the SLA, MOLA and LITE space lidar. Recent MOLA measurements of the Mars surface have 40 cm resolution and have reduced the global uncertainty in Mars topography from a few km to approx. 10 m. GLAS is a next generation lidar being developed as part of NASA's Icesat Mission for Earth orbit . The GLAS design combines a 10 cm precision surface lidar with a sensitive dual wavelength cloud and aerosol lidar. GLAS will precisely measure the heights of the Earth's polar ice sheets, determine the height profiles of the Earth's land topography, and profile the vertical backscatter of clouds and aerosols on a global scale. GLAS will fly on a small dedicated spacecraft in a polar orbit at 598 km altitude with an inclination of 94 degrees. GLAS is scheduled to launch in summer 2001 and to operate continuously for a minimum of 3 years with a goal of 5 years. The primary mission for GLAS is to measure the seasonal and annual changes in the heights of the Greenland and Antarctic ice sheets. GLAS will measure the vertical distance to the ice sheet from orbit with 1064 nm pulses from a Nd:Yag laser at 40 Hz. Each 5 nsec wide laser pulse is used for a single range measurement. When over land GLAS will profile the heights of the topography and vegetation. The GLAS receiver uses a I m diameter telescope and a Si APD detector. The detector signal is sampled by an all digital receiver which records each surface echo waveform with I nsec resolution and a stored echo record lengths of either 200, 400, or 600 samples. Analysis of the echo waveforms within the instrument permits discrimination between cloud and surface echoes. Ground based echo analysis permits precise ranging, determining the roughness or slopes of the surface as well as the vertical distributions of vegetation illuminated by the laser, Errors in knowledge of the laser beam pointing angle can bias height measurements of sloped surfaces. For surfaces with 2 deg. slopes, knowledge of pointing angle of the beam centroid to about 8 urad is required to achieve 10 cm height accuracy. GLAS uses a stellar reference system (SRS) to determine the pointing angle of each laser firing relative to inertial space. The SRS uses a high precision star camera oriented toward local zenith whose measurements are combined with a gyroscope to determine the inertial orientation of the SRS optical bench. The far field pattern of each laser pulse is measured with a laser reference system (LRS). Optically measuring each laser far field pattern relative to the star camera and gyroscope permits the angular offsets of each laser pulse to be determined. GLAS will also determine the vertical distributions of clouds and aerosols by measuring atmospheric backscatter profiles at both 1064 and 532 nm. The 1064 nm measurements use an analog detector and profile the height and vertical structure of thicker clouds. Measurements at 532 nm use new highly sensitive photon counting detectors, and measure the height distributions of very thin clouds and aerosol layers. With averaging these can be used to determine the height of the planetary boundary layer. The instrument design and expected performance will be discussed.

Deep Convective Cloud Top Heights and Their Thermodynamic Control During CRYSTAL-FACE

NASA Technical Reports Server (NTRS)

Sherwood, Steven C.; Minnis, Patrick; McGill, Matthew

2004-01-01

Infrared (11 micron) radiances from GOES-8 and local radiosonde profiles, collected during the Cirrus Regional Study of Tropical Anvils and Cirrus Layers-Florida Area Cirrus Experiment (CRYSTAL-FACE) in July 2002, are used to assess the vertical distribution of Florida-area deep convective cloud top height and test predictions as to its variation based on parcel theory. The highest infrared tops (Z(sub 11)) reached approximately to the cold point, though there is at least a 1-km uncertainty due to unknown cloud-environment temperature differences. Since lidar shows that visible 'tops' are 1 km or more above Z(sub 11), visible cloud tops frequently penetrated the lapse-rate tropopause (approx. 15 km). Further, since lofted ice content may be present up to approx. 1 km above the visible tops, lofting of moisture through the mean cold point (15.4 km) was probably common. Morning clouds, and those near Key West, rarely penetrated the tropopause. Non-entraining parcel theory (i.e., CAPE) does not successfully explain either of these results, but can explain some of the day-to-day variations in cloud top height over the peninsula. Further, moisture variations above the boundary layer account for most of the day-today variability not explained by CAPE, especially over the oceans. In all locations, a 20% increase in mean mixing ratio between 750 and 500 hPa was associated with about 1 km deeper maximum cloud penetration relative to the neutral level. These results suggest that parcel theory may be useful for predicting changes in cumulus cloud height over time, but that parcel entrainment must be taken into account even for the tallest clouds. Accordingly, relative humidity above the boundary layer may exert some control on the height of the tropical troposphere.

Correcting the hooking effect in satellite altimetry data for time series estimation over smaller rivers

NASA Astrophysics Data System (ADS)

Boergens, Eva; Dettmering, Denise; Schwatke, Christian

2015-04-01

Since many years the numbers of in-situ gauging stations are declining. Satellite altimetry can be used as a gap-filler even over smaller inland waters like rivers. However, since altimetry measurements are not designed for inland water bodies a special data handling is necessary in order to estimate reliable water level heights over inland waters. We developed a new routine for estimating water level heights over smaller inland waters with satellite altimetry by correcting the hooking effect. The hooking effect occurs when the altimeter is not measuring in nadir before and after passing a water body due to the stronger reflectance of the water than the surrounding land surface. These off-nadir measurements, together with the motion of the satellite, lead to overlong ranges and heights declining in a parabolic shape. The vertex of this parabola is on the water surface. Therefore, by estimating the parabola we are able to determine the water level height without the need of any point over the water body itself. For estimating the parabola we only use selected measurements which are effected by the hooking effect. The applied search approach is based on the RANSAC algorithm (random sample consensus) which is a non-deterministic algorithm especially designed for finding geometric entities in point clouds with many outliers. With the hooking effect correction we are able to retrieve water level height time series from the Mekong River from Envisat and Saral/Altika high frequency data. It is possible to determine reliable time series even if the river has only a width of 500m or less. The expected annual variations are clearly depicted and the comparison of the time series with available in-situ gauging data shows a very good agreement.

From prenatal life into senescence, testosterone is essential requirement for manhood.

PubMed

Pradidarcheep, Wisuit; Showpittapornchai, Udomsri

2009-04-01

Prenatally, organisms have the bipotentiality to differentiate along either male or female lines, a process with different stages, each with a narrow window of time, during which testosterone plays a pivotal role in the case of male sexual differentiation. During puberty, the body directs the masculinization process with growth of the genitalia and prostate. Body contours become male, with an average height of 10-15 centimeters greater than that of females, a greater bone and muscle mass, a male hair pattern and a male-type fat distribution. These pubertal developments, largely reversible in case of severe androgen deficiency, require adult levels of testosterone throughout life. A new area of interest is in exploring how far age-related body changes (loss of bone and muscle mass, a shift into a higher ratio of body fat/lean body mass) are part of an age-related decline of testicular testosterone production. Therefore, throughout life, testosterone is essential for a normal male life.

Direct Observation of 2D Electrostatics and Ohmic Contacts in Template-Grown Graphene/WS2 Heterostructures.

PubMed

Zheng, Changxi; Zhang, Qianhui; Weber, Bent; Ilatikhameneh, Hesameddin; Chen, Fan; Sahasrabudhe, Harshad; Rahman, Rajib; Li, Shiqiang; Chen, Zhen; Hellerstedt, Jack; Zhang, Yupeng; Duan, Wen Hui; Bao, Qiaoliang; Fuhrer, Michael S

2017-03-28

Large-area two-dimensional (2D) heterojunctions are promising building blocks of 2D circuits. Understanding their intriguing electrostatics is pivotal but largely hindered by the lack of direct observations. Here graphene-WS 2 heterojunctions are prepared over large areas using a seedless ambient-pressure chemical vapor deposition technique. Kelvin probe force microscopy, photoluminescence spectroscopy, and scanning tunneling microscopy characterize the doping in graphene-WS 2 heterojunctions as-grown on sapphire and transferred to SiO 2 with and without thermal annealing. Both p-n and n-n junctions are observed, and a flat-band condition (zero Schottky barrier height) is found for lightly n-doped WS 2 , promising low-resistance ohmic contacts. This indicates a more favorable band alignment for graphene-WS 2 than has been predicted, likely explaining the low barriers observed in transport experiments on similar heterojunctions. Electrostatic modeling demonstrates that the large depletion width of the graphene-WS 2 junction reflects the electrostatics of the one-dimensional junction between two-dimensional materials.

Analysis of Non-Pivotal Bioequivalence Studies Submitted in Abbreviated New Drug Submissions for Delayed-Release Drug Products.

PubMed

Kaur, Paramjeet; Jiang, Xiaojian; Stier, Ethan

2017-01-01

The US FDA's rule on "Requirements for Submission of Bioequivalence Data" requiring submission of all bioequivalence (BE) studies conducted on the same formulation of the drug product submitted for approval was published in Federal Register in January 2009. With the publication of this rule, we evaluated the impact of data from non-pivotal BE studies in assessing BE and identified the reasons for failed in vivo BE studies for generic oral delayed-release (DR) drug products only. We searched the Agency databases from January 2009 toDecember 2016 to identify Abbreviated New Drug Applications (ANDAs) submitted for DR drug products containing non-pivotal BE studies. Out of 202 ANDAs, 43 ANDAs contained 102 non-pivotal BE studies. Forty-nine non-pivotal BE studies were conducted on the to-be-marketed (TBM) formulation and 53 were conducted on formulations different from the TBM formulation. These experimental formulations primarily differed in the ratio of components of the enteric coating layer and/or amount (i.e., %w/w) of enteric coating layer. Of the 49 non-pivotal BE studies conducted on the TBM formulation, 41 failed to meet the BE acceptance criteria. The majority of failed non-pivotal BE studies on the TBM DR generic products had insufficient power, which was expected as these studies are exploratory in nature and not designed to have adequate power to pass the BE statistical criteria. In addition, among the failed non-pivotal BE studies on the TBM DR generic products, the most commonly failing pharmacokinetic parameter was Cmax. The data from these non-pivotal BE studies indicate that inadequate BE study design can lead to failure of the BE on the same formulation. Also, the non-pivotal BE studies on formulations different from the TBM formulation help us link the formulation design to the product performance in vivo. This article is open to POST-PUBLICATION REVIEW. Registered readers (see "For Readers") may comment by clicking on ABSTRACT on the issue's contents page.

A form of two-phase sampling utilizing regression analysis

Treesearch

Michael A. Fiery; John R. Brooks

2007-01-01

A two-phase sampling technique was introduced and tested on several horizontal point sampling inventories of hardwood tracts located in northern West Virginia and western Maryland. In this sampling procedure species and dbh are recorded for all “in-trees” on all sample points. Sawlog merchantable height was recorded on a subsample of intensively measured (second phase...

Taper and volume equations for selected Appalachian hardwood species

Treesearch

A. Jeff Martin

1981-01-01

Coefficients for five taper/volume models are developed for 18 Appalachian hardwood species. Each model can be used to estimate diameter at any point on the bole, height to any preselected diameter, and cubic-foot volume between any two points on the bole. The resulting equations were tested on six sets of independent data and an evaluation of these tests is included,...

43 CFR 3832.42 - How do I locate a tunnel site?

Code of Federal Regulations, 2013 CFR

2013-10-01

... substantial post, board, or monument at the face of the tunnel, which is the point where the tunnel enters... height and width of the tunnel; and (4) The course and distance from the face or starting point to some... boundary lines of the tunnel at proper intervals as required under state law from the face of the tunnel...

43 CFR 3832.42 - How do I locate a tunnel site?

Code of Federal Regulations, 2012 CFR

2012-10-01

... substantial post, board, or monument at the face of the tunnel, which is the point where the tunnel enters... height and width of the tunnel; and (4) The course and distance from the face or starting point to some... boundary lines of the tunnel at proper intervals as required under state law from the face of the tunnel...

Designing and Testing a UAV Mapping System for Agricultural Field Surveying

PubMed Central

Skovsen, Søren

2017-01-01

A Light Detection and Ranging (LiDAR) sensor mounted on an Unmanned Aerial Vehicle (UAV) can map the overflown environment in point clouds. Mapped canopy heights allow for the estimation of crop biomass in agriculture. The work presented in this paper contributes to sensory UAV setup design for mapping and textual analysis of agricultural fields. LiDAR data are combined with data from Global Navigation Satellite System (GNSS) and Inertial Measurement Unit (IMU) sensors to conduct environment mapping for point clouds. The proposed method facilitates LiDAR recordings in an experimental winter wheat field. Crop height estimates ranging from 0.35–0.58 m are correlated to the applied nitrogen treatments of 0–300 kgNha. The LiDAR point clouds are recorded, mapped, and analysed using the functionalities of the Robot Operating System (ROS) and the Point Cloud Library (PCL). Crop volume estimation is based on a voxel grid with a spatial resolution of 0.04 × 0.04 × 0.001 m. Two different flight patterns are evaluated at an altitude of 6 m to determine the impacts of the mapped LiDAR measurements on crop volume estimations. PMID:29168783

Designing and Testing a UAV Mapping System for Agricultural Field Surveying.

PubMed

Christiansen, Martin Peter; Laursen, Morten Stigaard; Jørgensen, Rasmus Nyholm; Skovsen, Søren; Gislum, René

2017-11-23

A Light Detection and Ranging (LiDAR) sensor mounted on an Unmanned Aerial Vehicle (UAV) can map the overflown environment in point clouds. Mapped canopy heights allow for the estimation of crop biomass in agriculture. The work presented in this paper contributes to sensory UAV setup design for mapping and textual analysis of agricultural fields. LiDAR data are combined with data from Global Navigation Satellite System (GNSS) and Inertial Measurement Unit (IMU) sensors to conduct environment mapping for point clouds. The proposed method facilitates LiDAR recordings in an experimental winter wheat field. Crop height estimates ranging from 0.35-0.58 m are correlated to the applied nitrogen treatments of 0-300 kg N ha . The LiDAR point clouds are recorded, mapped, and analysed using the functionalities of the Robot Operating System (ROS) and the Point Cloud Library (PCL). Crop volume estimation is based on a voxel grid with a spatial resolution of 0.04 × 0.04 × 0.001 m. Two different flight patterns are evaluated at an altitude of 6 m to determine the impacts of the mapped LiDAR measurements on crop volume estimations.

Above-bottom biomass retrieval of aquatic plants with regression models and SfM data acquired by a UAV platform - A case study in Wild Duck Lake Wetland, Beijing, China

NASA Astrophysics Data System (ADS)

Jing, Ran; Gong, Zhaoning; Zhao, Wenji; Pu, Ruiliang; Deng, Lei

2017-12-01

Above-bottom biomass (ABB) is considered as an important parameter for measuring the growth status of aquatic plants, and is of great significance for assessing health status of wetland ecosystems. In this study, Structure from Motion (SfM) technique was used to rebuild the study area with high overlapped images acquired by an unmanned aerial vehicle (UAV). We generated orthoimages and SfM dense point cloud data, from which vegetation indices (VIs) and SfM point cloud variables including average height (HAVG), standard deviation of height (HSD) and coefficient of variation of height (HCV) were extracted. These VIs and SfM point cloud variables could effectively characterize the growth status of aquatic plants, and thus they could be used to develop a simple linear regression model (SLR) and a stepwise linear regression model (SWL) with field measured ABB samples of aquatic plants. We also utilized a decision tree method to discriminate different types of aquatic plants. The experimental results indicated that (1) the SfM technique could effectively process high overlapped UAV images and thus be suitable for the reconstruction of fine texture feature of aquatic plant canopy structure; and (2) an SWL model based on point cloud variables: HAVG, HSD, HCV and two VIs: NGRDI, ExGR as independent variables has produced the best predictive result of ABB of aquatic plants in the study area, with a coefficient of determination of 0.84 and a relative root mean square error of 7.13%. In this analysis, a novel method for the quantitative inversion of a growth parameter (i.e., ABB) of aquatic plants in wetlands was demonstrated.

Mapping Fearscapes of a Mammalian Herbivore using Terrestrial LiDAR and UAV Imagery

NASA Astrophysics Data System (ADS)

Olsoy, P.; Nobler, J. D.; Forbey, J.; Rachlow, J. L.; Burgess, M. A.; Glenn, N. F.; Shipley, L. A.

2013-12-01

Concealment allows prey animals to remain hidden from a predator and can influence both real and perceived risks of predation. The heterogeneous nature of vegetative structure can create a variable landscape of concealment - a 'fearscape' - that may influence habitat quality and use by prey. Traditional measurements of concealment rely on a limited number of distances, heights, and vantage points, resulting in small snapshots of concealment available to a prey animal. Our objective was to demonstrate the benefits of emerging remote sensing techniques to map fearscapes for pygmy rabbits (Brachylagus idahoensis) in sagebrush steppe habitat across a continuous range of scales. Specifically, we used vegetation height rasters derived from terrestrial laser scanning (TLS) to create viewsheds from multiple vantage points, representing predator visibility. The sum of all the viewsheds modeled horizontal concealment of prey at both the shrub and patch scales. We also used a small, unmanned aerial vehicle (UAV) to determine vertical concealment at a habitat scale. Terrestrial laser scanning provided similar estimates of horizontal concealment at the shrub scale when compared to photographic methods (R2 = 0.85). Both TLS and UAV provide the potential to quantify concealment of prey from multiple distances, heights, or vantage points, allowing the creation of a manipulable fearscape map that can be correlated with habitat use by prey animals. The predictive power of such a map also could identify shrubs or patches for fine scale nutritional and concealment analysis for future investigation and conservation efforts. Fearscape map at the mound-scale. Viewsheds were calculated from 100 equally spaced observer points located 4 m from the closest on-mound sagebrush of interest. Red areas offer low concealment, while green areas provide high concealment.

A comparison of measured versus self-reported anthropometrics for assessing obesity in adults: a literature review.

PubMed

Maukonen, Mirkka; Männistö, Satu; Tolonen, Hanna

2018-03-01

Up-to-date information on the accuracy between different anthropometric data collection methods is vital for the reliability of anthropometric data. A previous review on this matter was conducted a decade ago. Our aim was to conduct a literature review on the accuracy of self-reported height, weight, and body mass index (BMI) against measured values for assessing obesity in adults. To obtain an overview of the present situation, we included studies published after the previous review. Differences according to sex, BMI groups, and continents were also assessed. Studies published between January 2006 and April 2017 were identified from a literature search on PubMed. Our search retrieved 62 publications on adult populations that showed a tendency for self-reported height to be overestimated and weight to be underestimated when compared with measured values. The findings were similar for both sexes. BMI derived from self-reported height and weight was underestimated; there was a clear tendency for underestimation of overweight (from 1.8%-points to 9.8%-points) and obesity (from 0.7%-points to 13.4%-points) prevalence by self-report. The bias was greater in overweight and obese participants than those of normal weight. Studies conducted in North America showed a greater bias, whereas the bias in Asian studies seemed to be lower than those from other continents. With globally rising obesity rates, accurate estimation of obesity is essential for effective public health policies to support obesity prevention. As self-report bias tends to be higher among overweight and obese individuals, measured anthropometrics provide a more reliable tool for assessing the prevalence of obesity.

GNSS Antenna Caused Near-Field Interference Effect in Precise Point Positioning Results

NASA Astrophysics Data System (ADS)

Dawidowicz, Karol; Baryła, Radosław

2017-06-01

Results of long-term static GNSS observation processing adjustment prove that the often assumed "averaging multipath effect due to extended observation periods" does not actually apply. It is instead visible a bias that falsifies the coordinate estimation. The comparisons between the height difference measured with a geometrical precise leveling and the height difference provided by GNSS clearly verify the impact of the near-field multipath effect. The aim of this paper is analysis the near-field interference effect with respect to the coordinate domain. We demonstrate that the way of antennas mounting during observation campaign (distance from nearest antennas) can cause visible changes in pseudo-kinematic precise point positioning results. GNSS measured height differences comparison revealed that bias of up to 3 mm can be noticed in Up component when some object (additional GNSS antenna) was placed in radiating near-field region of measuring antenna. Additionally, for both processing scenario (GPS and GPS/GLONASS) the scattering of results clearly increased when additional antenna crosses radiating near-field region of measuring antenna. It is especially true for big choke ring antennas. In short session (15, 30 min.) the standard deviation was about twice bigger in comparison to scenario without additional antenna. When we used typical surveying antennas (short near-field region radius) the effect is almost invisible. In this case it can be observed the standard deviation increase of about 20%. On the other hand we found that surveying antennas are generally characterized by lower accuracy than choke ring antennas. The standard deviation obtained on point with this type of antenna was bigger in all processing scenarios (in comparison to standard deviation obtained on point with choke ring antenna).

Evaluation of Water Vapor Radiometer on HY-2A Satellite with the Ship-borne GNSS Observations over the India Ocean

NASA Astrophysics Data System (ADS)

Liu, Y.; Wu, Z.; Chen, G.; Liu, W.

2016-12-01

HY-2A is the first marine dynamic environment satellite in China. It is used to observe the global sea surface wind field, sea surface height, significant wave heights and sea surface temperature. In order to correct tropospheric delay in the radar altimeter measurements, the calibration microwave radiometer (CMR) is on board satellite. In this paper, a ship-borne GNSS experiment was done to evaluate the accuracy of water vapor content observed from CMR over the India Ocean in 2014. Because the HY-2A satellite orbit is in S-N direction, the ship course was designed in E-W direction to produce the cross-point over the ocean for the calibration. During two months experiment, three cross-points were captured on the 29th April/5th May/13th May. The GNSS data include GPS,GLONASS and BDS, and its sampling rate is 1s. The GNSS observations are processed with the Point Precise Positioning (PPP) algorithm by our software. The Precipitable Water Vapor (PWV) is better than 3mm accuracy, which is consistent with the results from NAVCOM and FUFRO. The GNSS derived PWV are compared with those from HY-2A CMR on the three cross-points. Their differences are -1.68mm,-0.88mm and -2.21mm respectively, and the average is -1.58mm. This result means the CMR derived PWV is good agreement with that from GNSS. It demonstrates that the HY-2A satellite has the ability of high accuracy water vapor measurement. It is quite beneficial to the radar altimeter for sea surface height measurements.

Double-inversion mechanisms of the X⁻ + CH₃Y [X,Y = F, Cl, Br, I] SN2 reactions.

PubMed

Szabó, István; Czakó, Gábor

2015-03-26

The double-inversion and front-side attack transition states as well as the proton-abstraction channels of the X(-) + CH3Y [X,Y = F, Cl, Br, I] reactions are characterized by the explicitly correlated CCSD(T)-F12b/aug-cc-pVTZ(-PP) level of theory using small-core relativistic effective core potentials and the corresponding aug-cc-pVTZ-PP bases for Br and I. In the X = F case the double-inversion classical(adiabatic) barrier heights are 28.7(25.6), 15.8(13.4), 13.2(11.0), and 8.6(6.6) kcal mol(-1) for Y = F, Cl, Br, and I, respectively, whereas the barrier heights are in the 40-90 kcal mol(-1) range for the other 12 reactions. The abstraction channels are always above the double-inversion saddle points. For X = F, the front-side attack classical(adiabatic) barrier heights, 45.8(44.8), 31.0(30.3), 24.7(24.2), and 19.5(19.3) kcal mol(-1) for Y = F, Cl, Br, and I, respectively, are higher than the corresponding double-inversion ones, whereas for the other systems the front-side attack saddle points are in the 35-70 kcal mol(-1) range. The double-inversion transition states have XH···CH2Y(-) structures with Cs point-group symmetry, and the front-side attack saddle points have either Cs (X = F or X = Y) or C1 symmetry with XCY angles in the 78-88° range. On the basis of the previous reaction dynamics simulations and the minimum energy path computations along the inversion coordinate of selected XH···CH2Y(-) systems, we suggest that the double inversion may be a general mechanism for SN2 reactions.

Design and evaluation of a single-pivot supported centrifugal blood pump.

PubMed

Yoshino, M; Uemura, M; Takahashi, K; Watanabe, N; Hoshi, H; Ohuchi, K; Nakamura, M; Fujita, H; Sakamoto, T; Takatani, S

2001-09-01

In order to develop a centrifugal blood pump that meets the requirements of a long-term, implantable circulatory support device, in this study a single-pivot bearing supported centrifugal blood pump was designed to evaluate its basic performance. The single-pivot structure consisted of a ceramic ball male pivot mounted on the bottom surface of the impeller and a polyethylene female pivot incorporated in the bottom pump casing. The follower magnet mounted inside the impeller was magnetically coupled to the driver magnet mounted on the shaft of the direct current brushless motor. As the motor rotated, the impeller rotated supported entirely by a single-pivot bearing system. The static pump performance obtained in the mock circulatory loop revealed an acceptable performance as a left ventricular assist device in terms of flow and head pressure. The pump flow of 5 L/min against the head pressure of 100 mm Hg was obtained at rotational speeds of 2,000 to 2,200 rpm. The maximum pump flow was 9 L/min with 2,200 rpm. The maximum electrical-to-hydraulic power conversion efficiency was around 14% at pump flows of 4 to 5 L/min. The stability of the impeller was demonstrated at the pump rpm higher than 1,400 with a single-pivot bearing without an additional support at its top. The single-pivot supported centrifugal pump can provide adequate flow and pressure as a ventricular assist device, but its mechanical stability and hemolytic as well as thrombotic performances must be tested prior to clinical use.

40 CFR 61.24 - Annual reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., including their location, diameter, flow rate, effluent temperature and release height. (5) A description of...) Distances from the points of release to the nearest residence, school, business or office and the nearest...

Predicting the limits to tree height using statistical regressions of leaf traits.

PubMed

Burgess, Stephen S O; Dawson, Todd E

2007-01-01

Leaf morphology and physiological functioning demonstrate considerable plasticity within tree crowns, with various leaf traits often exhibiting pronounced vertical gradients in very tall trees. It has been proposed that the trajectory of these gradients, as determined by regression methods, could be used in conjunction with theoretical biophysical limits to estimate the maximum height to which trees can grow. Here, we examined this approach using published and new experimental data from tall conifer and angiosperm species. We showed that height predictions were sensitive to tree-to-tree variation in the shape of the regression and to the biophysical endpoints selected. We examined the suitability of proposed end-points and their theoretical validity. We also noted that site and environment influenced height predictions considerably. Use of leaf mass per unit area or leaf water potential coupled with vulnerability of twigs to cavitation poses a number of difficulties for predicting tree height. Photosynthetic rate and carbon isotope discrimination show more promise, but in the second case, the complex relationship between light, water availability, photosynthetic capacity and internal conductance to CO(2) must first be characterized.

The role of height in the sex difference in intelligence.

PubMed

Kanazawa, Satoshi; Reyniers, Diane J

2009-01-01

Recent studies conclude that men on average have higher intelligence than women by 3-5 IQ points. However, the ultimate evolutionary question of why men should have evolved to have higher intelligence than women remains. We suggest that men may have slightly higher intelligence than women through 4 mechanisms: (1) assortative mating of intelligent men and beautiful women, (2) assortative mating of tall men and beautiful women, (3) an extrinsic correlation between height and intelligence produced by Mechanisms 1 and 2, and (4) a higher-than-expected offspring sex ratio (more sons) among tall (and hence intelligent) parents. Consistent with our suggestion, we show that men may have higher IQs than women because they are taller, and once we control for height women have slightly higher IQs than men.The correlation between height and IQ and the female advantage in intelligence persist even after we control for health as a measure of genetic quality, as well as physical attractiveness, age, race, education, and earnings. Height is also strongly associated with intelligence within each sex.

The challenge of tree height in Eucalyptus regnans: when xylem tapering overcomes hydraulic resistance.

PubMed

Petit, Giai; Pfautsch, Sebastian; Anfodillo, Tommaso; Adams, Mark A

2010-09-01

*Recent research suggests that increasing conduit tapering progressively reduces hydraulic constraints caused by tree height. Here, we tested this hypothesis using the tallest hardwood species, Eucalyptus regnans. *Vertical profiles of conduit dimensions and vessel density were measured for three mature trees of height 47, 51 and 63 m. *Mean hydraulic diameter (Dh) increased rapidly from the tree apex to the point of crown insertion, with the greatest degree of tapering yet reported (b > 0.33). Conduit tapering was such that most of the total resistance was found close to the apex (82-93% within the first 1 m of stem) and the path length effect was reduced by a factor of 2000. Vessel density (VD) declined from the apex to the base of each tree, with scaling parameters being similar for all trees (a = 4.6; b = -0.5). *Eucalyptus regnans has evolved a novel xylem design that ensures a high hydraulic efficiency. This feature enables the species to grow quickly to heights of 50-60 m, beyond the maximum height of most other hardwood trees.

Comparable Analysis of the Distribution Functions of Runup Heights of the 1896, 1933 and 2011 Japanese Tsunamis in the Sanriku Area

NASA Astrophysics Data System (ADS)

Choi, B. H.; Min, B. I.; Yoshinobu, T.; Kim, K. O.; Pelinovsky, E.

2012-04-01

Data from a field survey of the 2011 tsunami in the Sanriku area of Japan is presented and used to plot the distribution function of runup heights along the coast. It is shown that the distribution function can be approximated using a theoretical log-normal curve [Choi et al, 2002]. The characteristics of the distribution functions derived from the runup-heights data obtained during the 2011 event are compared with data from two previous gigantic tsunamis (1896 and 1933) that occurred in almost the same region. The number of observations during the last tsunami is very large (more than 5,247), which provides an opportunity to revise the conception of the distribution of tsunami wave heights and the relationship between statistical characteristics and number of observations suggested by Kajiura [1983]. The distribution function of the 2011 event demonstrates the sensitivity to the number of observation points (many of them cannot be considered independent measurements) and can be used to determine the characteristic scale of the coast, which corresponds to the statistical independence of observed wave heights.

Understanding Rasch Measurement: Partial Credit Model and Pivot Anchoring.

ERIC Educational Resources Information Center

Bode, Rita K.

2001-01-01

Describes the Rasch measurement partial credit model, what it is, how it differs from other Rasch models, and when and how to use it. Also describes the calibration of instruments with increasingly complex items. Explains pivot anchoring and illustrates its use and describes the effect of pivot anchoring on step calibrations, item hierarchy, and…

Motion systems providing three or four degrees of freedom

NASA Technical Reports Server (NTRS)

Chou, Richard C. (Inventor)

1982-01-01

A motion system is provided by a platform generally parallel to a base and connected thereto by a column and powered and controlled extensible members, at least three of which are connected between distributed points around the column. In a three degree of freedom device, the column is conical, rigidly supported at its base with a universal joint at its top. The points of attachment define triangles in the base and in the platform surrounding the column with one extensible member connected between each. In the four degree of freedom version, the column is modified by making it effectively a column which is pivoted or guided at the base or contains an extensible member, preferably retains its triangular shape and its universal joint connection to the platform at its apex. For stability four powered and controlled extensible members are provided between points in the base and platform distributed around the column, a preferred pattern of arrangement being a square with the column at the center.

Public involvement in research: making sense of the diversity.

PubMed

Oliver, Sandy; Liabo, Kristin; Stewart, Ruth; Rees, Rebecca

2015-01-01

This paper presents a coherent framework for designing and evaluating public involvement in research by drawing on an extensive literature and the authors' experience. The framework consists of three key interrelated dimensions: the drivers for involvement; the processes for involvement and the impact of involvement. The pivotal point in this framework is the opportunity for researchers and others to exchange ideas. This opportunity results from the processes which bring them together and which support their debates and decisions. It is also the point at which research that is in the public interest is open to public influence and the point at which the interaction can also influence anyone directly involved. Judicious choice of methods for bringing people together, and supporting their debate and decisions, depends upon the drivers of those involved; these vary with their characteristics, particularly their degree of enthusiasm and experience, and their motivation. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Point of Care- A Novel Approach to Periodontal Diagnosis-A Review

PubMed Central

Nayak, Prathibha Anand; Rana, Shivendra

2017-01-01

Periodontal disease, one of the prevalent oral diseases, is characterized by gingival inflammation and periodontal tissue destruction. Diagnosing this disease is challenging to the clinicians as the disease process is discontinuous and shows periods of exacerbation and remission. Traditional diagnostic methods basically tells about the past tissue destruction so new diagnostic methods are required which is able to detect the active state of the disease, determine the future progression and also estimates the response to the therapy, thereby helping in the better clinical management of the patient. Both saliva and Gingival crevicular fluid (GCF) are believed to be reliable medium to detect the biomarkers which plays a pivotal role in measuring the disease activity. Keeping these observations in mind rapid chairside tests are developed to diagnose periodontal disease called as Point of Care (POC) diagnostics which simplifies diagnosis and helps in improving the prognosis. This review article highlights about the biomarkers used in the diagnosis and throws light on the various available point of care diagnostic devices. PMID:28969294

Development of new demi-span equations from a nationally representative sample of older people to estimate adult height.

PubMed

Hirani, Vasant; Aresu, Maria

2012-03-01

To develop new equations for the calculation of body mass index (BMI) of adults aged 65 and older for when an actual height measurement may not be possible or reflect attained height because of loss of height with aging or conditions such as kyphosis or osteoporosis. Cross-sectional, nationally representative samples; data from 1994, 2000 2005, and 2007. Adults aged 65 and older living in England. Two thousand four hundred fifty-four noninstitutitionalized adults aged 65 and older taking part in the Health Survey for England (HSE). Height and demi-span measurements (defined as the distance between the mid-point of the sternal notch and the finger roots with the arm outstretched laterally) were taken according to standard procedures. Sex- and age-specific regression equations were produced from measured height and demi-span (DEH) using HSE 2005 data to develop new DEH equations (DEH(age)) from people aged 65 and older. The derived DEH(age) equation was applied to the HSE data for 1994, 2000, and 2007 to attempt to test its reliability. Analysis showed that DEH(age) predicts current height better than when using the Bassey equation (DEH(B) (assey)). DEH(age) can be used instead of a height measurement to derive other anthropometric indices such as body mass index (BMI) in older people. The new equations developed for predicting current height in older people can be used to calculate BMI more accurately in older people. © 2012, Copyright the Authors Journal compilation © 2012, The American Geriatrics Society.

The Heights of Mount Sharp

NASA Image and Video Library

2012-08-20

With the addition of four high-resolution Navigation Camera, or Navcam, images, taken on Aug. 18 Sol 12, Curiosity 360-degree landing-site panorama now includes the highest point on Mount Sharp visible from the rover.

Air Modeling - Observational Meteorological Data

EPA Pesticide Factsheets

Observed meteorological data for use in air quality modeling consist of physical parameters that are measured directly by instrumentation, and include temperature, dew point, wind direction, wind speed, cloud cover, cloud layer(s), ceiling height,

Intrinsic alignment of redMaPPer clusters: cluster shape-matter density correlation

NASA Astrophysics Data System (ADS)

van Uitert, Edo; Joachimi, Benjamin

2017-07-01

We measure the alignment of the shapes of galaxy clusters, as traced by their satellite distributions, with the matter density field using the public redMaPPer catalogue based on Sloan Digital Sky Survey-Data Release 8 (SDSS-DR8), which contains 26 111 clusters up to z ˜ 0.6. The clusters are split into nine redshift and richness samples; in each of them, we detect a positive alignment, showing that clusters point towards density peaks. We interpret the measurements within the tidal alignment paradigm, allowing for a richness and redshift dependence. The intrinsic alignment (IA) amplitude at the pivot redshift z = 0.3 and pivot richness λ = 30 is A_IA^gen=12.6_{-1.2}^{+1.5}. We obtain tentative evidence that the signal increases towards higher richness and lower redshift. Our measurements agree well with results of maxBCG clusters and with dark-matter-only simulations. Comparing our results to the IA measurements of luminous red galaxies, we find that the IA amplitude of galaxy clusters forms a smooth extension towards higher mass. This suggests that these systems share a common alignment mechanism, which can be exploited to improve our physical understanding of IA.

Role of proline and GABA in sexual reproduction of angiosperms

PubMed Central

Biancucci, Marco; Mattioli, Roberto; Forlani, Giuseppe; Funck, Dietmar; Costantino, Paolo; Trovato, Maurizio

2015-01-01

Two glutamate derivatives, proline and γ-aminobutyric acid (GABA), appear to play pivotal roles in different aspects of sexual reproduction in angiosperms, although their precise function in plant reproduction and the molecular basis of their action are not yet fully understood. Proline and GABA have long been regarded as pivotal amino acids in pollen vitality and fertility. Proline may constitute up to 70% of the free amino acid pool in pollen grains and it has been recently shown that Arabidopsis mutants affected in the first and rate-limiting step in proline synthesis produce aberrant and infertile pollen grains, indicating that proline synthesis is required for pollen development and fertility. Concerning GABA, a large body of evidence points to this glutamate derivative as a key determinant of post-pollination fertilization. Intriguingly, proline has also been associated with pollination, another aspect of sexual reproduction, since honeybees were reported to show a strong preference for proline-enriched nectars. In this review, we survey current knowledge on the roles of proline and GABA in plant fertility, and discuss future perspectives potentially capable to improve our understanding on the functions of these amino acids in pollen development, pollination, and pollen tube guidance. PMID:26388884

Pivot design in bileaflet valves.

PubMed

Vallana, F; Rinaldi, S; Galletti, P M; Nguyen, A; Piwnica, A

1992-01-01

The design criteria leading to the development of a new bileaflet valve (Sorin Bicarbon) were derived from the analysis of functional requirements, the performance of existing prostheses, and the availability of an advanced carbon coating technology (Carbofilm). The hinge is the critical element affecting fluid dynamics, durability, and thrombus formation in bileaflet valves. A comparative study of three existing models led to a new hinge design that was based on coupling two spheric surfaces with different radii of curvature (leaflet pivot and hinge recess) and obtained by electroerosion into a Carbofilm-coated metallic housing. In this valve, the point of contact moves continuously by rolling, not sliding. This minimizes friction and wear and allows uninterrupted washing of the blood exposed surfaces even during diastole (a finding established in patients using transesophageal echocardiography). Tricuspid implantation without anticoagulation in 33 sheep did not lead to thrombotic events (follow-up, 40-400 days). In the first 36 clinical implants observed for 15 months (mitral position, size 29; two unrelated deaths), the mean diastolic gradient by echo Doppler was 4 +/- 1.25 mmHg; the functional area was 3.2 +/- 0.6 cm2. No leaflet fracture and no thrombotic or embolic complications were observed clinically using a standard anticoagulant regimen.

Parachuting harnesses comparative evaluation on energy distribution grids.

PubMed

Hembecker, Paula Karina; Poletto, Angela Regina; Gontijo, Leila Amaral

2012-01-01

This research aims to make a comparative evaluation of three different parachuting harnesses to work at heights in the energy industry, from the electricians' point of view concerning these products under the optics of usability and ergonomic principles, and mainly justified by the high quantity of injuries at the energy industry due to high falls. According to its main target, this field research is classified as exploratory-descriptive transversal viewing study and, considering this perspective, the study was developed in four steps. Research results have enlightened the weakest spots and the potential improvement opportunities of these products, developed to assure safety of the work at heights to the energy industry, according to the opinion of the users. Still, results point that, regardless of the model, these devices have adapting issues to fulfill the electrical sector user's needs.

An empirical study of preferred settings for lumbar support on adjustable office chairs.

PubMed

Coleman, N; Hull, B P; Ellitt, G

1998-04-01

The preferred settings for lumbar support height and depth of 43 male and 80 female office workers were investigated. All subjects were equipped with identical modern office chairs with foam-padded backrests adjustable in both height and depth. Measurements of lumbar support settings were recorded in the workplace, outside of working hours, on four different occasions, over a 5 week period. Preferred lumbar support height and depth settings extended to both extremes of the adjustment range. The mean preferred height setting was 190 mm above the compressed seat surface. The mean depth setting (horizontal distance from front of seat to lumbar support point) was 387 mm. A regression model examining the effects of standing height, Body Mass Index (BMI) and gender on mean preferred lumbar support height showed a significant relationship between preferred height and BMI. Higher lumbar supports were chosen by subjects with greater BMIs. Gender and standing height were not associated with preferred lumbar support height settings. Preferred lumbar support depth was not significantly associated with standing height, gender or BMI. Older subjects were more likely to readjust their lumbar support from a disrupted position than younger subjects, indicating that older users are more sensitive to the position of their lumbar support. Subjects who reported recent back pain or discomfort that they believed to be associated with their chair or office work were found to set their lumbar support significantly closer to the front of the seat, probably to ensure greater support for their back. Based on the evidence that a high proportion of users do make adjustments to the height and depth of their lumbar support, and the finding that different groups of users, with different physical characteristics, adjust the position of their lumbar support in distinct and predictable ways, the researchers conclude that office chairs with traditional padded fixed-height lumbar supports are unlikely to provide a comfortable or appropriate seat for the wide range of potential users.

Electromagnetic wave scattering from rough terrain

NASA Astrophysics Data System (ADS)

Papa, R. J.; Lennon, J. F.; Taylor, R. L.

1980-09-01

This report presents two aspects of a program designed to calculate electromagnetic scattering from rough terrain: (1) the use of statistical estimation techniques to determine topographic parameters and (2) the results of a single-roughness-scale scattering calculation based on those parameters, including comparison with experimental data. In the statistical part of the present calculation, digitized topographic maps are used to generate data bases for the required scattering cells. The application of estimation theory to the data leads to the specification of statistical parameters for each cell. The estimated parameters are then used in a hypothesis test to decide on a probability density function (PDF) that represents the height distribution in the cell. Initially, the formulation uses a single observation of the multivariate data. A subsequent approach involves multiple observations of the heights on a bivariate basis, and further refinements are being considered. The electromagnetic scattering analysis, the second topic, calculates the amount of specular and diffuse multipath power reaching a monopulse receiver from a pulsed beacon positioned over a rough Earth. The program allows for spatial inhomogeneities and multiple specular reflection points. The analysis of shadowing by the rough surface has been extended to the case where the surface heights are distributed exponentially. The calculated loss of boresight pointing accuracy attributable to diffuse multipath is then compared with the experimental results. The extent of the specular region, the use of localized height variations, and the effect of the azimuthal variation in power pattern are all assessed.

Point-of-Prescription Interventions to Improve Antimicrobial Stewardship

PubMed Central

Hamilton, Keith W.; Gerber, Jeffrey S.; Moehring, Rebekah; Anderson, Deverick J.; Calderwood, Michael S.; Han, Jennifer H.; Mehta, Jimish M.; Pollack, Lori A.; Zaoutis, Theoklis; Srinivasan, Arjun; Camins, Bernard C.; Schwartz, David N.; Lautenbach, Ebbing

2015-01-01

Antimicrobial stewardship is pivotal to improving patient outcomes, reducing adverse events, decreasing healthcare costs, and preventing further emergence of antimicrobial resistance. In an era in which antimicrobial resistance is increasing, judicious antimicrobial use is the responsibility of every healthcare provider. Antimicrobial stewardship programs (ASPs) have made headway in improving antimicrobial prescribing using such “top-down” methods as formulary restriction and prospective audit with feedback; however, engagement of prescribers has not been fully explored. Strategies that include frontline prescribers and other unit-based healthcare providers have the potential to expand stewardship, both to augment existing centralized ASPs and to provide alternative approaches to perform stewardship at healthcare facilities with limited resources. This review discusses interventions focusing on antimicrobial prescribing at the point of prescription as well as a pilot project to engage unit-based healthcare providers in antimicrobial stewardship. PMID:25595748

Dissimilar Kinetic Behavior of Electrically Manipulated Single- and Double-Stranded DNA Tethered to a Gold Surface

PubMed Central

Rant, Ulrich; Arinaga, Kenji; Tornow, Marc; Kim, Yong Woon; Netz, Roland R.; Fujita, Shozo; Yokoyama, Naoki; Abstreiter, Gerhard

2006-01-01

We report on the electrical manipulation of single- and double-stranded oligodeoxynucleotides that are end tethered to gold surfaces in electrolyte solution. The response to alternating repulsive and attractive electric surface fields is studied by time-resolved fluorescence measurements, revealing markedly distinct dynamics for the flexible single-stranded and stiff double-stranded DNA, respectively. Hydrodynamic simulations rationalize this finding and disclose two different kinetic mechanisms: stiff polymers undergo rotation around the anchoring pivot point; flexible polymers, on the other hand, are pulled onto the attracting surface segment by segment. PMID:16473909

Dissimilar kinetic behavior of electrically manipulated single- and double-stranded DNA tethered to a gold surface.

PubMed

Rant, Ulrich; Arinaga, Kenji; Tornow, Marc; Kim, Yong Woon; Netz, Roland R; Fujita, Shozo; Yokoyama, Naoki; Abstreiter, Gerhard

2006-05-15

We report on the electrical manipulation of single- and double-stranded oligodeoxynucleotides that are end tethered to gold surfaces in electrolyte solution. The response to alternating repulsive and attractive electric surface fields is studied by time-resolved fluorescence measurements, revealing markedly distinct dynamics for the flexible single-stranded and stiff double-stranded DNA, respectively. Hydrodynamic simulations rationalize this finding and disclose two different kinetic mechanisms: stiff polymers undergo rotation around the anchoring pivot point; flexible polymers, on the other hand, are pulled onto the attracting surface segment by segment.

The what, how, why, and where of self-construal.

PubMed

Cross, Susan E; Hardin, Erin E; Gercek-Swing, Berna

2011-05-01

Since the publication of Markus and Kitayama's pivotal article on culture and the self, the concepts of independent, relational, and interdependent self-construal have become important constructs in cultural psychology and research on the self. The authors review the history of these constructs, their measurement and manipulation, and their roles in cognition, emotion, motivation, and social behavior. They make suggestions for future research and point to problems still to be sorted out. Researchers interested in these constructs have many opportunities to make important contributions to the literature in a variety of fields, including health psychology, education, counseling, and international relations.

Transport as a system: reorganization of perinatal assistance in Northern Lombardy.

PubMed

Martinelli, Stefano; Vergani, Patrizia; Zanini, Rinaldo; Bellù, Roberto; Farina, Clotilde; Tagliabue, Paolo

2011-10-01

The organization of perinatal care has been a pivotal mean for improvement in neonatal survivals. Despite the excellent standard of assistance in Lombardy, Obstetrics and Neonatal Units of MBBM Foundation-Monza, Manzoni Hospital-Lecco and Niguarda Hospital-Milan put forward a pilot project proposing reorganization of perinatal care in the northern part of Lombardy. The main goals of the project are implementation of maternal transport system and use of neonatal back transport as a system to increase the availability of intensive care beds. The project's fundamental steps and critical points will be discussed.

E-2578

NASA Image and Video Library

1956-09-27

NACA High-Speed Flight Station test pilot Stan Butchart flying the Iron Cross, the mechanical reaction control simulator. High-pressure nitrogen gas expanded selectively, by the pilot, through the small reaction control thrusters maneuvered the Iron Cross through the three axes. The exhaust plume can be seen from the aft thruster. The tanks containing the gas can be seen on the cart at the base of the pivot point of the Iron Cross. NACA technicians built the iron-frame simulator, which matched the inertia ratios of the Bell X-1B airplane, installing six jet nozzles to control the movement about the three axes of pitch, roll, and yaw.

Dem Generation with WORLDVIEW-2 Images

NASA Astrophysics Data System (ADS)

Büyüksalih, G.; Baz, I.; Alkan, M.; Jacobsen, K.

2012-07-01

For planning purposes 42 km coast line of the Black Sea, starting at the Bosporus going in West direction, with a width of approximately 5 km, was imaged by WorldView-2. Three stereo scenes have been oriented at first by 3D-affine transformation and later by bias corrected RPC solution. The result is nearly the same, but it is limited by identification of the control points in the images. Nevertheless after blunder elimination by data snooping root mean square discrepancies below 1 pixel have been reached. The root mean square discrepancy at control point height reached 0.5 m up to 1.3 m with a base to height relation between 1:1.26 and 1:1.80. Digital Surface models (DSM) with 4 m spacing have been generated by least squares matching with region growing, supported by image pyramids. A higher percentage of the mountainous area is covered by forest, requiring the approximation based on image pyramids. In the forest area the approximation just by region growing leads to larger gaps in the DSM. Caused by the good image quality of WorldView-2 the correlation coefficients reached by least squares matching are high and even in most forest areas a satisfying density of accepted points was reached. Two stereo models have an overlapping area of 1.6 km times 6.7 km allowing an accuracy evaluation. Small, but nevertheless significant differences in scene orientation have been eliminated by least squares shift of both overlapping height models to each other. The root mean square differences of both independent DSM are 1.06m or as a function of terrain inclination 0.74 m + 0.55 m  tangent (slope). The terrain inclination in the average is 7° with 12% exceeding 17°. The frequency distribution of height discrepancies is not far away from normal distribution, but as usual, larger discrepancies are more often available as corresponding to normal distribution. This also can be seen by the normalized medium absolute deviation (NMAS) related to 68% probability level of 0.83m being significant smaller as the root mean square differences. Nevertheless the results indicate a standard deviation of the single height models of 0.75 m or 0.52 m + 0.39* tangent (slope), corresponding to approximately 0.6 pixels for the x-parallax in flat terrain, being very satisfying for the available land cover. An interpolation over 10 m enlarged the root mean square differences of both height models nearly by 50%.

Cervix-to-rectum measuring device in a radiation applicator for use in the treatment of cervical cancer

NASA Technical Reports Server (NTRS)

Fischell, D. R.; Mazique, J. C. (Inventor)

1981-01-01

A cervix-to-rectum measuring device to be used in the treatment of cervical cancer is described. It includes a handle and a probe pivotably connected to the handle for insertion in the rectum. The measuring device further includes means for coupling the handle to an intrauterine radiation applicator when the latter is positioned in the uterine cervix and the probe is inserted in the rectum to pivot the handle about the probe. A gear is provided which is adapted to pivot with the probe. A pinion pivotably connected to the handle meshes with the gear. A pointer fixed to the pinion is displaced in response to the pivoting of the handle about the probe, and this displacement can be read from a scale on the handle, providing an indication of the cervix-to-rectum distance.

Pivot tables for mortality analysis, or who needs life tables anyway?

PubMed

Wesley, David; Cox, Hugh F

2007-01-01

Actuarial life-table analysis has long been used by life insurance medical directors for mortality abstraction from clinical studies. Ironically, today's life actuary instead uses pivot tables to analyze mortality. Pivot tables (a feature/function in MS Excel) collapse various dimensions of data that were previously arranged in an "experience study" format. Summary statistics such as actual deaths, actual and expected mortality (usually measured in dollars), and calculated results such as actual to expected ratios, are then displayed in a 2-dimensional grid. The same analytic process, excluding the dollar focus, can be used for clinical mortality studies. For raw survival data, especially large datasets, this combination of experience study data and pivot tables has clear advantages over life-table analysis in both accuracy and flexibility. Using the SEER breast cancer data, we compare the results of life-table analysis and pivot-table analysis.

A Robust Gradient Based Method for Building Extraction from LiDAR and Photogrammetric Imagery.

PubMed

Siddiqui, Fasahat Ullah; Teng, Shyh Wei; Awrangjeb, Mohammad; Lu, Guojun

2016-07-19

Existing automatic building extraction methods are not effective in extracting buildings which are small in size and have transparent roofs. The application of large area threshold prohibits detection of small buildings and the use of ground points in generating the building mask prevents detection of transparent buildings. In addition, the existing methods use numerous parameters to extract buildings in complex environments, e.g., hilly area and high vegetation. However, the empirical tuning of large number of parameters reduces the robustness of building extraction methods. This paper proposes a novel Gradient-based Building Extraction (GBE) method to address these limitations. The proposed method transforms the Light Detection And Ranging (LiDAR) height information into intensity image without interpolation of point heights and then analyses the gradient information in the image. Generally, building roof planes have a constant height change along the slope of a roof plane whereas trees have a random height change. With such an analysis, buildings of a greater range of sizes with a transparent or opaque roof can be extracted. In addition, a local colour matching approach is introduced as a post-processing stage to eliminate trees. This stage of our proposed method does not require any manual setting and all parameters are set automatically from the data. The other post processing stages including variance, point density and shadow elimination are also applied to verify the extracted buildings, where comparatively fewer empirically set parameters are used. The performance of the proposed GBE method is evaluated on two benchmark data sets by using the object and pixel based metrics (completeness, correctness and quality). Our experimental results show the effectiveness of the proposed method in eliminating trees, extracting buildings of all sizes, and extracting buildings with and without transparent roof. When compared with current state-of-the-art building extraction methods, the proposed method outperforms the existing methods in various evaluation metrics.

A Robust Gradient Based Method for Building Extraction from LiDAR and Photogrammetric Imagery

PubMed Central

Siddiqui, Fasahat Ullah; Teng, Shyh Wei; Awrangjeb, Mohammad; Lu, Guojun

2016-01-01

Existing automatic building extraction methods are not effective in extracting buildings which are small in size and have transparent roofs. The application of large area threshold prohibits detection of small buildings and the use of ground points in generating the building mask prevents detection of transparent buildings. In addition, the existing methods use numerous parameters to extract buildings in complex environments, e.g., hilly area and high vegetation. However, the empirical tuning of large number of parameters reduces the robustness of building extraction methods. This paper proposes a novel Gradient-based Building Extraction (GBE) method to address these limitations. The proposed method transforms the Light Detection And Ranging (LiDAR) height information into intensity image without interpolation of point heights and then analyses the gradient information in the image. Generally, building roof planes have a constant height change along the slope of a roof plane whereas trees have a random height change. With such an analysis, buildings of a greater range of sizes with a transparent or opaque roof can be extracted. In addition, a local colour matching approach is introduced as a post-processing stage to eliminate trees. This stage of our proposed method does not require any manual setting and all parameters are set automatically from the data. The other post processing stages including variance, point density and shadow elimination are also applied to verify the extracted buildings, where comparatively fewer empirically set parameters are used. The performance of the proposed GBE method is evaluated on two benchmark data sets by using the object and pixel based metrics (completeness, correctness and quality). Our experimental results show the effectiveness of the proposed method in eliminating trees, extracting buildings of all sizes, and extracting buildings with and without transparent roof. When compared with current state-of-the-art building extraction methods, the proposed method outperforms the existing methods in various evaluation metrics. PMID:27447631

A Reliable Method to Measure Lip Height Using Photogrammetry in Unilateral Cleft Lip Patients.

PubMed

van der Zeeuw, Frederique; Murabit, Amera; Volcano, Johnny; Torensma, Bart; Patel, Brijesh; Hay, Norman; Thorburn, Guy; Morris, Paul; Sommerlad, Brian; Gnarra, Maria; van der Horst, Chantal; Kangesu, Loshan

2015-09-01

There is still no reliable tool to determine the outcome of the repaired unilateral cleft lip (UCL). The aim of this study was therefore to develop an accurate, reliable tool to measure vertical lip height from photographs. The authors measured the vertical height of the cutaneous and vermilion parts of the lip in 72 anterior-posterior view photographs of 17 patients with repairs to a UCL. Points on the lip's white roll and vermillion were marked on both the cleft and the noncleft sides on each image. Two new concepts were tested. First, photographs were standardized using the horizontal (medial to lateral) eye fissure width (EFW) for calibration. Second, the authors tested the interpupillary line (IPL) and the alar base line (ABL) for their reliability as horizontal lines of reference. Measurements were taken by 2 independent researchers, at 2 different time points each. Overall 2304 data points were obtained and analyzed. Results showed that the method was very effective in measuring the height of the lip on the cleft side with the noncleft side. When using the IPL, inter- and intra-rater reliability was 0.99 to 1.0, with the ABL it varied from 0.91 to 0.99 with one exception at 0.84. The IPL was easier to define because in some subjects the overhanging nasal tip obscured the alar base and gave more consistent measurements possibly because the reconstructed alar base was sometimes indistinct. However, measurements from the IPL can only give the percentage difference between the left and right sides of the lip, whereas those from the ABL can also give exact measurements. Patient examples were given that show how the measurements correlate with clinical assessment. The authors propose this method of photogrammetry with the innovative use of the IPL as a reliable horizontal plane and use of the EFW for calibration as a useful and reliable tool to assess the outcome of UCL repair.

A Valentine from Vesta

NASA Image and Video Library

2012-02-14

This image from NASA Dawn spacecraft, is based on a framing camera image that is overlain by a color-coded height representation of topography. This heart-shaped hollow is roughly 10 kilometers 6 miles across at its widest point.

Effects of lisdexamfetamine dimesylate treatment for ADHD on growth.

PubMed

Faraone, Stephen V; Spencer, Thomas J; Kollins, Scott H; Glatt, Stephen J

2010-01-01

To complete an exploratory uncontrolled study of the effects of lisdexamfetamine dimesylate (LDX) on growth of children treated for attention-deficit/hyperactivity disorder (ADHD). Height, weight, and body mass index (BMI) from 281 children ages 6 to 13 years from longitudinal assessments up to 15 months were compared to norms from the Centers for Disease Control. At study entry, children were taller and heavier than average. Growth delays were largest for weight and BMI, and there was a 13 percentile point decrease in height. Children continued to grow in terms of height while treated with LDX; we found no increase in raw weight or BMI during the study period. LDX treatment was significantly associated with diminished gains in height, weight, and BMI compared to levels that would be expected based on age-appropriate standards from the Centers for Disease Control. Growth delays were greatest for the heaviest and tallest children, for those who had not previously received stimulant therapy, and for those with a greater cumulative exposure to LDX. More work is needed to determine effects on ultimate adult height. Consistent with prior studies of stimulants, treatment with LDX leads to statistically significant reductions in expected height, weight, and BMI. Growth of patients with ADHD treated with LDX should be closely monitored and corrective action taken should growth delays be observed.

Articulation at shoulder level--a pilot experimental study on car seat comfort.

PubMed

Coelho, Denis Alves; Dahlman, Sven

2012-01-01

This article reports on a pilot experimental study aimed at a first evaluation of the introduction of an articulation in the upper part of the seat backrest. The idea of introducing this articulation sprang from prevention of whiplash injuries and this study tentatively assesses its potential for improvement in comfort. This was done considering a pre-defined articulation height. A height for the articulation of 43.5 cm above the H-point of a reference seat was theoretically deduced based on a population with an average sitting height of 88 cm. Participants evaluated the articulated seat in comparison with the reference seat. Twelve participants were divided into three groups of sitting height. In a laboratory environment subjective comfort evaluations and preferred values of deployment of the articulation and of counter-tilting of the headrest were registered. Driving on the roads completed and validated the laboratory assessments. The reference seat was deemed less comfortable for the participants with short and medium sitting height than for the tall ones. There was a notable improvement in comfort for most of the medium and short sitting height participants when using the articulated seat. The articulation was fully deployed by most participants. Copyright © 2011 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Discussion on Height Systems in Stereoscopic Mapping Using the ZY-3 Satellite Images

NASA Astrophysics Data System (ADS)

Zhao, L.; Fu, X.; Zhu, G.; Zhang, J.; Han, C.; Cheng, L.

2018-04-01

The ZY-3 is the civil high-resolution optical stereoscopic mapping satellite independently developed by China. It is mainly used for 1 : 50,000 scale topographic mapping. One of the distinguishing features of the ZY-3 is that the panchromatic triplet camera can obtain thousands of kilometers of continuous strip stereo data. The working mode is suitable for wide-range stereoscopic mapping, in particular global DEM extraction. The ZY-3 constellation is operated in a sun-synchronous at an altitude 505 km, with a 10:30 AM equator crossing time and a 29-day revisiting period. The panchromatic triplet sensors have excellent base-to-height ratio, which is advantageous for obtaining good mapping accuracy. In this paper the China quasi-geoid, EGM2008 and the height conversion method are discussed. It is pointed out that according to the current surveying and mapping specifications, almost all maps and charts use mean sea level for elevation. Experiments on bundle adjustment and DEM extraction with different height systems have been carried out in Liaoning Province of China. The results show that the similar accuracy can be obtained using different elevation system. According to the principle of geodesy and photogrammetry, it is recommended to use ellipsoidal height for satellite photogrammetric calculation and use the orthometric height in mapping production.

Light extraction block with curved surface

DOEpatents

Levermore, Peter; Krall, Emory; Silvernail, Jeffrey; Rajan, Kamala; Brown, Julia J.

2016-03-22

Light extraction blocks, and OLED lighting panels using light extraction blocks, are described, in which the light extraction blocks include various curved shapes that provide improved light extraction properties compared to parallel emissive surface, and a thinner form factor and better light extraction than a hemisphere. Lighting systems described herein may include a light source with an OLED panel. A light extraction block with a three-dimensional light emitting surface may be optically coupled to the light source. The three-dimensional light emitting surface of the block may includes a substantially curved surface, with further characteristics related to the curvature of the surface at given points. A first radius of curvature corresponding to a maximum principal curvature k.sub.1 at a point p on the substantially curved surface may be greater than a maximum height of the light extraction block. A maximum height of the light extraction block may be less than 50% of a maximum width of the light extraction block. Surfaces with cross sections made up of line segments and inflection points may also be fit to approximated curves for calculating the radius of curvature.

Geoscience laser altimeter system-stellar reference system

NASA Astrophysics Data System (ADS)

Millar, Pamela S.; Sirota, J. Marcos

1998-01-01

GLAS is an EOS space-based laser altimeter being developed to profile the height of the Earth's ice sheets with ~15 cm single shot accuracy from space under NASA's Mission to Planet Earth (MTPE). The primary science goal of GLAS is to determine if the ice sheets are increasing or diminishing for climate change modeling. This is achieved by measuring the ice sheet heights over Greenland and Antarctica to 1.5 cm/yr over 100 km×100 km areas by crossover analysis (Zwally 1994). This measurement performance requires the instrument to determine the pointing of the laser beam to ~5 urad (1 arcsecond), 1-sigma, with respect to the inertial reference frame. The GLAS design incorporates a stellar reference system (SRS) to relate the laser beam pointing angle to the star field with this accuracy. This is the first time a spaceborne laser altimeter is measuring pointing to such high accuracy. The design for the stellar reference system combines an attitude determination system (ADS) with a laser reference system (LRS) to meet this requirement. The SRS approach and expected performance are described in this paper.

Hard turning micro-machine tool

DOEpatents

DeVor, Richard E; Adair, Kurt; Kapoor, Shiv G

2013-10-22

A micro-scale apparatus for supporting a tool for hard turning comprises a base, a pivot coupled to the base, an actuator coupled to the base, and at least one member coupled to the actuator at one end and rotatably coupled to the pivot at another end. A tool mount is disposed on the at least one member. The at least one member defines a first lever arm between the pivot and the tool mount, and a second lever arm between the pivot and the actuator. The first lever arm has a length that is less than a length of the second lever arm. The actuator moves the tool mount along an arc.

PiVoT GPS Receiver

NASA Technical Reports Server (NTRS)

Wennersten, Miriam; Banes, Vince; Boegner, Greg; Clagnett, Charles; Dougherty, Lamar; Edwards, Bernard; Roman, Joe; Bauer, Frank H. (Technical Monitor)

2001-01-01

NASA Goddard Space Flight Center has built an open architecture, 24 channel spaceflight Global Positioning System (GPS) receiver. The compact PCI PiVoT GPS receiver card is based on the Mitel/GEC Plessey Builder 2 board. PiVoT uses two Plessey 2021 correlators to allow tracking of up to 24 separate GPS SV's on unique channels. Its four front ends can support four independent antennas, making it a useful card for hosting GPS attitude determination algorithms. It has been built using space quality, radiation tolerant parts. The PiVoT card works at a lower signal to noise ratio than the original Builder 2 board. It also hosts an improved clock oscillator. The PiVoT software is based on the original Piessey Builder 2 software ported to the Linux operating system. The software is posix compliant and can be easily converted to other posix operating systems. The software is open source to anyone with a licensing agreement with Plessey. Additional tasks can be added to the software to support GPS science experiments or attitude determination algorithms. The next generation PiVoT receiver will be a single radiation hardened compact PCI card containing the microprocessor and the GPS receiver optimized for use above the GPS constellation.

Continuous wavelength tunable laser source with optimum positioning of pivot axis for grating

DOEpatents

Pushkarsky, Michael; Amone, David F.

2010-06-08

A laser source (10) for generating a continuously wavelength tunable light (12) includes a gain media (16), an optical output coupler (36F), a cavity collimator (38A), a diffraction grating (30), a grating beam (54), and a beam attacher (56). The diffraction grating (30) is spaced apart from the cavity collimator (38A) and the grating (30) cooperates with the optical output coupler (36F) to define an external cavity (32). The grating (30) includes a grating face surface (42A) that is in a grating plane (42B). The beam attacher (56) retains the grating beam (54) and allows the grating beam (54) and the grating (30) to effectively pivot about a pivot axis (33) that is located approximately at an intersection of a pivot plane (50) and the grating plane (42B). As provided herein, the diffraction grating (30) can be pivoted about the unique pivot axis (33) to move the diffraction grating (30) relative to the gain media (16) to continuously tune the lasing frequency of the external cavity (32) and the wavelength of the output light (12) so that the output light (12) is mode hop free.

Gender differences in offaxis neuromuscular control during stepping under a slippery condition.

PubMed

Lee, Song Joo; Ren, Yupeng; Geiger, François; Zhang, Li-Qun

2013-11-01

Females are at greater risks of musculoskeletal injuries than are males, which may be related to decreased neuromuscular control in axial and/or frontal planes, offaxis neuromuscular control. The objective of this study was to investigate gender differences in offaxis neuromuscular control during stepping under a slippery condition. Forty-three healthy subjects (21 males and 22 females) performed different stepping tasks under a slippery condition, namely, free pivoting task (FPT) to control axial plane pivoting, free sliding task (FST) to control frontal plane sliding, and free pivoting and sliding task (FPST) to control axial pivoting, and frontal sliding on a custom-made offaxis elliptical trainer. Compared to males, females showed significantly higher pivoting instability, higher max internal and external pivoting angles, higher mean max medial and lateral sliding distance, and higher entropy of time to peak EMG in the medial and lateral gastrocnemius muscles during the FPST and higher entropy of time to peak EMG in the lateral gastrocnemius muscle during the FPT and FST. The findings may help us understand potential injury risk factors associated with gender differences, and provide a basis for developing targeted neuromuscular training to improve offaxis neuromuscular control, and reduce musculoskeletal injuries associated with excessive offaxis loadings.

Wind-influenced projectile motion

NASA Astrophysics Data System (ADS)

Bernardo, Reginald Christian; Perico Esguerra, Jose; Day Vallejos, Jazmine; Jerard Canda, Jeff

2015-03-01

We solved the wind-influenced projectile motion problem with the same initial and final heights and obtained exact analytical expressions for the shape of the trajectory, range, maximum height, time of flight, time of ascent, and time of descent with the help of the Lambert W function. It turns out that the range and maximum horizontal displacement are not always equal. When launched at a critical angle, the projectile will return to its starting position. It turns out that a launch angle of 90° maximizes the time of flight, time of ascent, time of descent, and maximum height and that the launch angle corresponding to maximum range can be obtained by solving a transcendental equation. Finally, we expressed in a parametric equation the locus of points corresponding to maximum heights for projectiles launched from the ground with the same initial speed in all directions. We used the results to estimate how much a moderate wind can modify a golf ball’s range and suggested other possible applications.

A method for measuring aircraft height and velocity using dual television cameras

NASA Technical Reports Server (NTRS)

Young, W. R.

1977-01-01

A unique electronic optical technique, consisting of two closed circuit television cameras and timing electronics, was devised to measure an aircraft's horizontal velocity and height above ground without the need for airborne cooperative devices. The system is intended to be used where the aircraft has a predictable flight path and a height of less than 660 meters (2,000 feet) at or near the end of an air terminal runway, but is suitable for greater aircraft altitudes whenever the aircraft remains visible. Two television cameras, pointed at zenith, are placed in line with the expected path of travel of the aircraft. Velocity is determined by measuring the time it takes the aircraft to travel the measured distance between cameras. Height is determined by correlating this speed with the time required to cross the field of view of either camera. Preliminary tests with a breadboard version of the system and a small model aircraft indicate the technique is feasible.

Height Distribution Between Cloud and Aerosol Layers from the GLAS Spaceborne Lidar in the Indian Ocean Region

NASA Technical Reports Server (NTRS)

Hart, William D.; Spinhirne, James D.; Palm, Steven P.; Hlavka, Dennis L.

2005-01-01

The Geoscience Laser Altimeter System (GLAS), a nadir pointing lidar on the Ice Cloud and land Elevation Satellite (ICESat) launched in 2003, now provides important new global measurements of the relationship between the height distribution of cloud and aerosol layers. GLAS data have the capability to detect, locate, and distinguish between cloud and aerosol layers in the atmosphere up to 40 km altitude. The data product algorithm tests the product of the maximum attenuated backscatter coefficient b'(r) and the vertical gradient of b'(r) within a layer against a predetermined threshold. An initial case result for the critical Indian Ocean region is presented. From the results the relative height distribution between collocated aerosol and cloud shows extensive regions where cloud formation is well within dense aerosol scattering layers at the surface. Citation: Hart, W. D., J. D. Spinhime, S. P. Palm, and D. L. Hlavka (2005), Height distribution between cloud and aerosol layers from the GLAS spaceborne lidar in the Indian Ocean region,

G3X-K theory: A composite theoretical method for thermochemical kinetics

NASA Astrophysics Data System (ADS)

da Silva, Gabriel

2013-02-01

A composite theoretical method for accurate thermochemical kinetics, G3X-K, is described. This method is accurate to around 0.5 kcal mol-1 for barrier heights and 0.8 kcal mol-1 for enthalpies of formation. G3X-K is a modification of G3SX theory using the M06-2X density functional for structures and zero-point energies and parameterized for a test set of 223 heats of formation and 23 barrier heights. A reduced perturbation-order variant, G3X(MP3)-K, is also developed, providing around 0.7 kcal mol-1 accuracy for barrier heights and 0.9 kcal mol-1 accuracy for enthalpies, at reduced computational cost. Some opportunities to further improve Gn composite methods are identified and briefly discussed.

Acute Effect of Foam Rolling and Dynamic Stretching on Flexibility and Jump Height.

PubMed

Smith, Jason C; Pridgeon, Brooke; Hall, MacGregor C

2018-04-04

Smith, JC, Pridgeon, B, and Hall, MC. Acute effect of foam rolling and dynamic stretching on flexibility and jump height. J Strength Cond Res XX(X): 000-000, 2017-Dynamic stretching (DS) can acutely improve vertical jump (VJ) performance but its effect lasts no more than 5 minutes. Foam rolling (FR), a form of self-myofascial release, can acutely increase range of motion (ROM) with this effect lasting less than 10 minutes. Therefore, the purpose of this study was to evaluate the time course of these effects, separately and combined, on VJ height and ROM. Twenty-nine university students completed 4 different sessions (control, FR, DS, and combo) in a randomized order. After a warm-up and baseline assessments of VJ height and sit-and-reach, participants rested (control) and performed FR, DS, and the combination of FR and DS (combo). Vertical jump height and ROM were assessed every 5 minutes for 20 minutes after treatment. Mean scores at each time point were expressed as a percent change from baseline scores. Immediately after FR, sit-and-reach was significantly greater than control (p = 0.003). Vertical jump height immediately after treatment for DS and combo was significantly greater than the control and FR counterparts (p ≤ 0.002). Vertical jump height for DS and combo was also significantly greater than the control counterpart at 5 minutes after treatment (p < 0.001). At 15 minutes after treatment, the percent change in VJ height for the combo was significantly greater than the control counterpart (p = 0.002). Although FR has no effect on VJ performance, it can acutely increase ROM, but its effect was quickly dissipated. Foam rolling does not seem to enhance VJ height either alone or in combination with DS.

Clinical measurement of the height of the interproximal contact area in maxillary anterior teeth.

PubMed

Sghaireen, Mohd G; Al-Zarea, Bader K; Al-Shorman, Hisham M; Al-Omiri, Mahmoud K

2013-11-01

To clinically quantify the apicoincisal height of interproximal areas directly in patients' mouths. Thirty participants (11 females and 9 males, mean age=26±1.5 years) were recruited into this study. Measurement of interproximal contact areas was carried out directly in patients' mouths using digital caliper (TERENSA, USA) with measuring accuracy of 0.01 mm. The interproximal contact areas that were measured are: central incisor to central incisor, central incisor to lateral incisor, lateral incisor to canine, and canine to first premolar on both sides of the jaw. Statistical significance was based on probability values less than 0.05 (p<0.05). The largest contact point was the one present between central incisors and it ranged from 2.9 to 6.5 mm. On the other hand, the contact point between canine and first premolar was the smallest on both sides of the arch and ranged from 0.6 to 2.5 mm. The dimensions of the contact points declined as we move from anterior area backwards. Statistical analysis using t-test showed that there were significant differences between the measurements of interproximal points of each tooth (P<0.05). the apicogingival dimension of the contact point decreased as we moved from anterior to posterior teeth. The contact area between the central incisors was largest and the one between canine and premolar was the smallest. This study is the first to report direct intra-oral clinical measurement of contact points. Clinical evaluation of contact point dimensions using digital caliber is a viable, quick and accurate method to use.

40 CFR 436.152 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY.... The height difference between the maximum safe surge capacity level and the normal operating level...

40 CFR 436.142 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY.... The height difference between the maximum safe surge capacity level and the normal operating level...

40 CFR 436.132 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY.... The height difference between the maximum safe surge capacity level and the normal operating level...

40 CFR 436.52 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY.... The height difference between the maximum safe surge capacity level and the normal operating level...

Study of Fission Barrier Heights of Uranium Isotopes by the Macroscopic-Microscopic Method

NASA Astrophysics Data System (ADS)

Zhong, Chun-Lai; Fan, Tie-Shuan

2014-09-01

Potential energy surfaces of uranium nuclei in the range of mass numbers 229 through 244 are investigated in the framework of the macroscopic-microscopic model and the heights of static fission barriers are obtained in terms of a double-humped structure. The macroscopic part of the nuclear energy is calculated according to Lublin—Strasbourg-drop (LSD) model. Shell and pairing corrections as the microscopic part are calculated with a folded-Yukawa single-particle potential. The calculation is carried out in a five-dimensional parameter space of the generalized Lawrence shapes. In order to extract saddle points on the potential energy surface, a new algorithm which can effectively find an optimal fission path leading from the ground state to the scission point is developed. The comparison of our results with available experimental data and others' theoretical results confirms the reliability of our calculations.

Effect on radioactivity concentration estimation of radon progenies with NaI(Tl) pulse height distribution from considering geometric structure around detector and infiltration of radionuclides.

PubMed

Hirouchi, J; Terasaka, Y; Hirao, S; Moriizumi, J; Yamazawa, H

2015-11-01

The surface radioactivity concentrations of the radon progenies, (214)Pb and (214)Bi, were estimated from NaI(Tl) pulse height distributions during rain. The improvement in estimation errors caused by considering geometric structures around measuring points and infiltration of radionuclides was discussed. The surface radioactivity concentrations were determined by comparing the count rates at the full-energy peak ranges between observation and calculation with the electron-photon transport code EGS5. It was shown that the concentrations can be underestimated by about 30 % unless the obstacles around the detector or infiltration of radionuclides are considered in gamma ray transfer calculations at measuring points, where there are many tall obstacles, or the ground is covered with unpaved areas. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Topside Ionospheric Response to Solar EUV Variability

NASA Astrophysics Data System (ADS)

Anderson, P. C.; Hawkins, J.

2015-12-01

We present an analysis of 23 years of thermal plasma measurements in the topside ionosphere from several DMSP spacecraft at ~800 km. The solar cycle variations of the daily averaged densities, temperatures, and H+/O+ ratios show a strong relationship to the solar EUV as described by the E10.7 solar EUV proxy with cross-correlation coefficients (CCCs) with the density greater than 0.85. The H+/O+ varies dramatically from solar maximum when it is O+ dominated to solar minimum when it is H+ dominated. These ionospheric parameters also vary strongly with season, particularly at latitudes well away from the equator where the solar zenith angle (SZA) varies greatly with season. There are strong 27-day solar rotation periodicities in the density, associated with the periodicities in the solar EUV as measured by the TIMED SEE and SDO EVE instruments, with CCCs at times greater than 0.9 at selected wavelengths. Empirical Orthogonal Function (EOF) analysis captures over 95% of the variation in the density over the 23 years in the first two principle components. The first principle component (PC1) is clearly associated with the solar EUV showing a 0.91 CCC with the E10.7 proxy while the PC1 EOFs remain relatively constant with latitude indicating that the solar EUV effects are relatively independent of latitude. The second principle component (PC2) is clearly associated with the SZA variation, showing strong correlations with the SZA and the concomitant density variations at latitudes away from the equator and with the PC2 EOFs having magnitudes near zero at the equator and maximum at high latitude. The magnitude of the variation of the response of the topside ionosphere to solar EUV variability is shown to be closely related to the composition. This is interpreted as the result of the effect of composition on the scale height in the topside ionosphere and the "pivot effect" in which the variation in density near the F2 peak is expected to be amplified by a factor of e at an altitude a scale height above the F2 peak. When the topside ionosphere is H+ dominated, DMSP may be much less than a scale height above the F2 peak while when it is O+ dominated, DMSP may be several scale heights above the F2 peak.

Effect of torsional stiffness and inertia on the dynamics of low aspect ratio flapping wings.

PubMed

Xiao, Qing; Hu, Jianxin; Liu, Hao

2014-03-01

Micro air vehicle-motivated aerodynamics in biological flight has been an important subject in the past decade. Inspired by the novel flapping wing mechanisms in insects, birds and bats, we have carried out a numerical study systematically investigating a three-dimensional flapping rigid wing with passively actuated lateral and rotational motion. Distinguishing it from the limited existing studies, this work performs a systematic examination on the effects of wing aspect ratio (AR = 1.0 to infinity), inertia (density ratio σ = 4-32), torsional stiffness (frequency ratio F = 1.5-10 and infinity) and pivot point (from chord-center to leading edge) on the dynamics response of a low AR rectangular wing under an initial zero speed flow field condition. The simulation results show that the symmetry breakdown of the flapping wing results in a forward/backward motion with a rotational pitching. When the wing reaches its stable periodic state, the induced pitching frequency is identical to its forced flapping frequency. However, depending on various kinematic and dynamic system parameters, (i.e. flapping frequency, density ratio and pitching axis), the lateral induced velocity shows a number of different oscillating frequencies. Furthermore, compared with a one degree of freedom (DoF) wing in the lateral direction only, the propulsion performance of such a two DoF wing relies very much on the magnitude of torsional stiffness adding on the pivot point, as well as its pitching axis. In all cases examined here, thrust force and moment generated by a long span wing is larger than that of a short wing, which is remarkably linked to the strong reverse von Kármán vortex street formed in the wake of a wing.

Toxic and genotoxic effects of the imazethapyr-based herbicide formulation Pivot H® on montevideo tree frog Hypsiboas pulchellus tadpoles (Anura, Hylidae).

PubMed

Pérez-Iglesias, J M; Soloneski, S; Nikoloff, N; Natale, G S; Larramendy, M L

2015-09-01

Acute lethal and sublethal toxicity of the imidazolinone imazethapyr (IMZT)-based commercial formulation herbicide Pivot H® (10.59% IMZT) was evaluated on Hypsiboas pulchellus tadpoles. Whereas mortality was used as the end point for lethality, frequency of micronuclei (MNs) and other nuclear abnormalities as well as DNA single-strand breaks evaluated by the single cell gel electrophoresis assay were employed to test genotoxicity. Behavioral, growth, developmental, and morphological abnormalities were also employed as sublethal end points. Mortality studies revealed equivalent LC50 (96h) values of 1.49mg/L (confidence limit, 1.09-1.63) and 1.55mg/L (confidence limit, 1.51-1.60) IMZT for Gosner stage (GS) 25 and GS36, respectively. Behavioral changes, i.e., irregular swimming and immobility, as well as a decreased frequency of keratodonts were observed. The herbicide increased the frequency of MNs in circulating erythrocytes of tadpoles exposed for 48h to the highest concentration assayed (1.17mg/L). However, regardless of the concentration of the herbicide assayed, an enhanced frequency of MNs was observed in tadpoles exposed for 96h. The herbicide was able to induce other nuclear abnormalities, i.e., blebbed and notched nuclei, only when tadpoles were exposed for 96h. In addition, we observed that exposure to IMZT within the 0.39-1.17mg/L range increased the genetic damage index in treatments lasting for both 48 and 96h. This study represents the first evidence of acute lethal and sublethal effects exerted by IMZT on amphibians. Finally, our findings highlight the properties of this herbicide that jeopardize nontarget living species exposed to IMZT. Copyright © 2015 Elsevier Inc. All rights reserved.

One-degree-of-freedom spherical model for the passive motion of the human ankle joint.

PubMed

Sancisi, Nicola; Baldisserri, Benedetta; Parenti-Castelli, Vincenzo; Belvedere, Claudio; Leardini, Alberto

2014-04-01

Mathematical modelling of mobility at the human ankle joint is essential for prosthetics and orthotic design. The scope of this study is to show that the ankle joint passive motion can be represented by a one-degree-of-freedom spherical motion. Moreover, this motion is modelled by a one-degree-of-freedom spherical parallel mechanism model, and the optimal pivot-point position is determined. Passive motion and anatomical data were taken from in vitro experiments in nine lower limb specimens. For each of these, a spherical mechanism, including the tibiofibular and talocalcaneal segments connected by a spherical pair and by the calcaneofibular and tibiocalcaneal ligament links, was defined from the corresponding experimental kinematics and geometry. An iterative procedure was used to optimize the geometry of the model, able to predict original experimental motion. The results of the simulations showed a good replication of the original natural motion, despite the numerous model assumptions and simplifications, with mean differences between experiments and predictions smaller than 1.3 mm (average 0.33 mm) for the three joint position components and smaller than 0.7° (average 0.32°) for the two out-of-sagittal plane rotations, once plotted versus the full flexion arc. The relevant pivot-point position after model optimization was found within the tibial mortise, but not exactly in a central location. The present combined experimental and modelling analysis of passive motion at the human ankle joint shows that a one degree-of-freedom spherical mechanism predicts well what is observed in real joints, although its computational complexity is comparable to the standard hinge joint model.

Defense Coastal/Estuarine Research Program (DCERP1)

DTIC Science & Technology

2013-05-10

also showed that the greater the mixing height and ventilation rate, the lower the PM2.5 concentrations, which points to the diluting effect of these... ventilation rate, the lower the resulting PM2.5 concentrations, which points to the diluting effects of these parameters on ambient PM2.5 concentration...and discharge (New River, tributary creeks) Chemistry: Nutrients, salinity, pH, oxygen , temperature (New River, NRE, tributary creeks) Sedimentology

Measurer’s Handbook: US Army and Marine Corps Anthropometric Surveys, 2010-2011

DTIC Science & Technology

2011-08-01

Circumference Ankle Circumference Heel Ankle Circumference Ball of Foot Circumference Bimalleolar Breadth Heel Breadth Lateral Malleolus Height...will be asked to put on a stocking from ankle to knee to compress the hair to prevent scan distortion. For all participants, sanitary protective...malleolus (outside ankle bone). Knee point, anterior - the most protruding point of the right kneecap of a seated participant. Medial malleolus - the

H{α} Surges Aroused by Newly-emerging Satellite Bipolar Magnetic Field

NASA Astrophysics Data System (ADS)

Wang, J. F.; Zhou, T. H.; Ji, H. S.

2013-07-01

An Hα surge event occurred at AR NOAA 11259 on 2011 July 22. According to the BBSO (Big Bear Solar Observatory) Hα line-center observations, three surges continuously ejected from the same region to the north of the main-sunspot of AR 11259. All of surges ejected along a straight trajectory, and looked like the reversed Eiffel Tower. The first and second surges had the same process. Two bright points firstly appeared to the north of the main-sunspot. After several minutes, a surge appeared between the two bright points, and then rapidly ejected when the two points got most brightness.When the surge reached the maximum height, it disappeared quickly. However, the third surge appeared without bright points, and its height was only half of the others. Compared with SDO/HMI (Solar Dynamics Observatory/Helioseismic and Magnetic Imager) line-of-sight magnetogram, more than one hour before the first surge appeared, a satellite bipolar magnetic field emerged from the surge-ejection region. The newly-emerging positive magnetic flux showed a distinct decrease several minutes earlier than the ejection of the surges. We assumed that the surges was associated with the reconnection between the newly-emerging bipolar magnetic field and the existing (sunspot) magnetic field.

a Light-Weight Laser Scanner for Uav Applications

NASA Astrophysics Data System (ADS)

Tommaselli, A. M. G.; Torres, F. M.

2016-06-01

Unmanned Aerial Vehicles (UAV) have been recognized as a tool for geospatial data acquisition due to their flexibility and favourable cost benefit ratio. The practical use of laser scanning devices on-board UAVs is also developing with new experimental and commercial systems. This paper describes a light-weight laser scanning system composed of an IbeoLux scanner, an Inertial Navigation System Span-IGM-S1, from Novatel, a Raspberry PI portable computer, which records data from both systems and an octopter UAV. The performance of this light-weight system was assessed both for accuracy and with respect to point density, using Ground Control Points (GCP) as reference. Two flights were performed with the UAV octopter carrying the equipment. In the first trial, the flight height was 100 m with six strips over a parking area. The second trial was carried out over an urban park with some buildings and artificial targets serving as reference Ground Control Points. In this experiment a flight height of 70 m was chosen to improve target response. Accuracy was assessed based on control points the coordinates of which were measured in the field. Results showed that vertical accuracy with this prototype is around 30 cm, which is acceptable for forest applications but this accuracy can be improved using further refinements in direct georeferencing and in the system calibration.

Early-life Determinants of Stunted Adolescent Girls and Boys in Matlab, Bangladesh

PubMed Central

Bosch, Alinda M.; Baqui, Abdullah H.; van Ginneken, Jeroen K.

2008-01-01

This paper presents the results of a longitudinal study, conducted in Matlab, Bangladesh, that examined to what extent the level of stunting in adolescence can be predicted by nutritional status in early childhood and maternal height. A linked set of data collected from the same individuals at two moments in time, i.e. early childhood (1988–1989) and adolescence (2001), was analyzed. The study found that the odds of being stunted in adolescence could be explained by the combined effect of being stunted in childhood and having a mother whose height was less than 145 cm. Also, girls were more likely than boys to be stunted in childhood, whereas boys were more likely than girls to be stunted in adolescence. The latter is probably attributable to differences in the pace of maturation. In terms of policy and (reproductive health) programmes, it is important to recall that adolescent girls whose height and weight were subnormal (weight <45 kg and height <145 cm) might run an obstetric risk. Following these cut-off points, 83% and 23% of 16-year-old girls in this study would face obstetric risk, respectively, for weight and height if they marry and become pregnant soon. PMID:18686552

Micro electro mechanical system optical switching

DOEpatents

Thorson, Kevin J; Stevens, Rick C; Kryzak, Charles J; Leininger, Brian S; Kornrumpf, William P; Forman, Glenn A; Iannotti, Joseph A; Spahn, Olga B; Cowan, William D; Dagel, Daryl J

2013-12-17

The present disclosure includes apparatus, system, and method embodiments that provide micro electo mechanical system optical switching and methods of manufacturing switches. For example, one optical switch embodiment includes at least one micro electro mechanical system type pivot mirror structure disposed along a path of an optical signal, the structure having a mirror and an actuator, and the mirror having a pivot axis along a first edge and having a second edge rotatable with respect to the pivot axis, the mirror being capable of and arranged to be actuated to pivot betweeen a position parallel to a plane of an optical signal and a position substantially normal to the plane of the optical signal.

Tool for use in lifting pin supported objects

NASA Technical Reports Server (NTRS)

Marzek, R. A.; Read, W. S. (Inventor)

1974-01-01

A tool for use in lifting a pin-supported, electronic package mounted in juxtaposition with the surface of an electronic circuit board is described. The tool is configured to be received beneath a pin-supported package and is characterized by a manually operable linkage, including an elongated, rigid link is supported for axial reciprocation and a pivotal link pinned to the body and supported for oscillation induced in response to axial motion imparted to the rigid link. A lifting plate is pivotally coupled to the distal end of the pivotal link so that oscillatory motion imparted to the pivotal link serves to move the plate vertically for elevating the plate into lifting engagement with the electronic package positioned thereabove.

Spectroscopic Study of a Dark Lane and a Cool Loop in a Solar Limb Active Region by Hinode/EIS

NASA Astrophysics Data System (ADS)

Lee, K.; Imada, S.; Moon, Y.; Lee, J.

2012-12-01

We investigate a cool loop and a dark lane over a limb active region on 2007 March 14 by the Hinode/EUV Imaging Spectrometer (EIS). The cool loop is clearly seen in the EIS spectral lines formed at the transition region temperature (log T = 5.8). The dark lane is characterized by an elongated faint structure in coronal spectral lines (log T = 5.8 - 6.1) and rooted on a bright point. We examine their electron densities, Doppler velocities, and non-thermal velocities as a function of distance from the limb using the spectral lines formed at different temperatures (log T = 5.4 - 6.4). The electron densities of the cool loop and the dark lane are derived from the density sensitive line pairs of Mg VII, Fe XII, and Fe XIV spectra. Under the hydrostatic equilibrium and isothermal assumption, we determine their temperatures from the density scale height. Comparing the scale height temperatures to the peak formation temperatures of the spectral lines, we note that the scale height temperature of the cool loop is consistent with a peak formation temperature of the Mg VII (log T = 5.8) and the scale height temperature of the dark lane is close to a peak formation temperature of the Fe XII and Fe XIII (log T = 6.1 - 6.2). It is interesting to note that the structures of the cool loop and the dark lane are most visible in these temperature lines. While the non-thermal velocity in the cool loop slightly decreases (less than 7 km {s-1}) along the loop, that in the dark lane sharply falls off with height. The variation of non-thermal velocity with height in the cool loop and the dark lane is contrast to that in off-limb polar coronal holes which are considered as source of the fast solar wind. Such a decrease in the non-thermal velocity may be explained by wave damping near the solar surface or turbulence due to magnetic reconnection near the bright point.

Basketball Performance Is Related to Maturity and Relative Age in Elite Adolescent Players.

PubMed

Torres-Unda, Jon; Zarrazquin, Idoia; Gravina, Leyre; Zubero, Jaime; Seco, Jesús; Gil, Susana M; Gil, Javier; Irazusta, Jon

2016-05-01

During a national championship, the anthropometric, physiological, and maturation characteristics of 13- to 14-year-old players of elite basketball teams and their association with sport performance were analyzed. Body parameters (weight, height, skinfold thicknesses, and lengths) were measured and physiological capacities assessed by sprint (20 m) and jump tests (i.e., countermovement jump with arm swing). Chronological age (CA) and maturity offset (years from age at peak height velocity; YAPHV) were calculated, and then predicted age at peak height velocity, as the difference between CA and YAPHV. Game performance was assessed with point averages and the performance index rating (PIR). The birth-date distribution of players was biased, those born early in the selection year outnumbering those born later. Anthropometric analysis indicated that players who performed better had longer body lengths. Physiological testing showed that semi-finalists had better sprint performance than quarter-finalists and those players with greater jump capacity scored more points. Early maturation and advanced maturity status were also associated with better PIR and scored points per game. Multiple blockwise regression analysis showed that, among the factors analyzed, YAPHV was the best predictor of basketball performance. In conclusion, around puberty, physical and physiological parameters associated with maturity and CA are important in determining the success of elite basketball players. Consequently, boys who are born in the second half of the year and/or late maturing tend to be marginalized or totally excluded, and not given the chance to play under equal conditions; their careers may then be held back by the relative disadvantage associated with inexperience.

Biomechanical considerations for distraction of the monobloc, Le Fort III, and Le Fort I segments.

PubMed

Figueroa, Alvaro A; Polley, John W; Figueroa, Aaron D

2010-09-01

Distraction osteogenesis is effective for correction of severe maxillary and midface hypoplasia. The vectors controlling the segment to be moved must be planned. This requires knowledge of the physical characteristics of the osteotomized bone segment, including the location of the center of mass (free body) and the center of resistance (restrained body). The purpose of this study was to determine the center of mass of the osteotomized monobloc, Le Fort III, and Le Fort I bone segments. A dry human skull was used to sequentially isolate three bone segments: monobloc, Le Fort III, and Le Fort I. Each segment was suspended from three different points, and digital photographs were obtained from each suspension. The photographs were digitally superimposed. The center of mass was determined by calculating the intersection of the suspension lines. The center of mass for the monobloc segment was located at a point 43.5 percent of the total height from the occlusal plane to the superior edge of the frontal bone supraorbital osteotomy. For the Le Fort III, it was located 38 percent of the total height from the occlusal plane to the superior edge of the osteotomized base of the nasal bones. For the Le Fort I, it was 53 percent of the total height from the occlusal plane to the superior edge of the osteotomized maxillary bone. Knowledge of the location of the center of mass in the monobloc, Le Fort III, and Le Fort I segments provides a starting point for the clinician when planning vectors for advancement with distraction.

Lidar characterization of crystalline silica generation and transport from a sand and gravel plant.

PubMed

Trzepla-Nabaglo, Krystyna; Shiraki, Ryoji; Holmén, Britt A

2006-04-30

Light detection and ranging (Lidar) remote sensing two-dimensional vertical and horizontal scans collected downwind of a sand and gravel plant were used to evaluate the generation and transport of geologic fugitive dust emitted by quarry operations. The lidar data give unsurpassed spatial resolution of the emitted dust, but lack quantitative particulate matter (PM) mass concentration data. Estimates of the airborne PM10 and crystalline silica concentrations were determined using linear relationships between point monitor PM10 and quartz content data with the lidar backscatter signal collected from the point monitor location. Lidar vertical profiles at different distances downwind from the plant were used to quantify the PM10 and quartz horizontal fluxes at 2-m vertical resolution as well as off-site emission factors. Emission factors on the order of 65-110 kg of PM10 (10-30 kg quartz) per daily truck activity or 2-4 kg/t product shipped (0.5-1 kg quartz/t) were quantified for this facility. The lidar results identify numerous elevated plumes at heights >30 m and maximum plume heights of 100 m that cannot be practically sampled by conventional point sampler arrays. The PM10 and quartz mass flux was greatest at 10-25 m height and decreased with distance from the main operation. Measures of facility activity were useful for explaining differences in mass flux and emission rates between days. The study results highlight the capabilities of lidar remote sensing for determining the spatial distribution of fugitive dust emitted by area sources with intermittent and spatially diverse dust generation rates.

Secular trends in growth and nutritional status of Mozambican school-aged children and adolescents.

PubMed

dos Santos, Fernanda Karina; Maia, José A R; Gomes, Thayse Natacha Q F; Daca, Timóteo; Madeira, Aspacia; Katzmarzyk, Peter T; Prista, António

2014-01-01

The purpose of this study was to examine secular changes in growth and nutritional status of Mozambican children and adolescents between 1992, 1999 and 2012. 3374 subjects (1600 boys, 1774 girls), distributed across the three time points (523 subjects in 1992; 1565 in 1999; and 1286 in 2012), were studied. Height and weight were measured, BMI was computed, and WHO cut-points were used to define nutritional status. ANCOVA models were used to compare height, weight and BMI across study years; chi-square was used to determine differences in the nutritional status prevalence across the years. Significant differences for boys were found for height and weight (p<0.05) across the three time points, where those from 2012 were the heaviest, but those in 1999 were the tallest, and for BMI the highest value was observed in 2012 (1992<2012, 1999<2012). Among girls, those from 1999 were the tallest (1992<1999, 1999>2012), and those from 2012 had the highest BMI (1999<2012). In general, similar patterns were observed when mean values were analyzed by age. A positive trend was observed for overweight and obesity prevalences, whereas a negative trend emerged for wasting, stunting-wasting (in boys), and normal-weight (in girls); no clear trend was evident for stunting. Significant positive changes in growth and nutritional status were observed among Mozambican youth from 1992 to 2012, which are associated with economic, social and cultural transitional processes, expressing a dual burden in this population, with reduction in malnourished youth in association with an increase in the prevalence of overweight and obesity.

SHOX mutations in idiopathic short stature and Leri-Weill dyschondrosteosis: frequency and phenotypic variability.

PubMed

Jorge, Alexander A L; Souza, Silvia C; Nishi, Miriam Y; Billerbeck, Ana E; Libório, Débora C C; Kim, Chong A; Arnhold, Ivo J P; Mendonca, Berenice B

2007-01-01

The frequency of SHOX mutations in children with idiopathic short stature (ISS) has been found to be variable. We analysed the SHOX gene in children with ISS and Leri-Weill dyschondrosteosis (LWD) and evaluated the phenotypic variability in patients harbouring SHOX mutations. Sixty-three ISS, nine LWD children and 21 affected relatives. SHOX gene deletion was evaluated by fluorescence in situ hybridization (FISH), Southern blotting and segregation study of polymorphic marker. Point mutations were assessed by direct DNA sequencing. None of the ISS patients presented SHOX deletions, but two (3.2%) presented heterozygous point mutations, including the novel R147H mutation. However, when ISS patients were selected by sitting height : height ratio (SH/H) for age > 2 SD, mutation frequency detection increased to 22%. Eight (89%) LWD patients had SHOX deletions, but none had point mutations. Analysis of the other relatives in the families carrying SHOX mutations identified 14 children and 17 adult patients. A broad phenotypic variability was observed in all families regarding short stature severity and Madelung deformities. However, the presence of disproportional height, assessed by SH/H, was observed in all children and 82% of adult patients, being the most common feature in our patients with SHOX mutations. Patients with SHOX mutations present a broad phenotypic variability. SHOX mutations are very frequent in LWD (89%), in opposition to ISS (3.2%) in our cohort. The use of SH/H SDS as a selection criterion increases the frequency of SHOX mutation detection to 22% and should be used for selecting ISS children to undergo SHOX mutation molecular studies.

Frozen-wave instability in near-critical hydrogen subjected to horizontal vibration under various gravity fields.

PubMed

Gandikota, G; Chatain, D; Amiroudine, S; Lyubimova, T; Beysens, D

2014-01-01

The frozen-wave instability which appears at a liquid-vapor interface when a harmonic vibration is applied in a direction tangential to it has been less studied until now. The present paper reports experiments on hydrogen (H2) in order to study this instability when the temperature is varied near its critical point for various gravity levels. Close to the critical point, a liquid-vapor density difference and surface tension can be continuously varied with temperature in a scaled, universal way. The effect of gravity on the height of the frozen waves at the interface is studied by performing the experiments in a magnetic facility where effective gravity that results from the coupling of the Earth's gravity and magnetic forces can be varied. The stability diagram of the instability is obtained. The experiments show a good agreement with an inviscid model [Fluid Dyn. 21 849 (1987)], irrespective of the gravity level. It is observed in the experiments that the height of the frozen waves varies weakly with temperature and increases with a decrease in the gravity level, according to a power law with an exponent of 0.7. It is concluded that the wave height becomes of the order of the cell size as the gravity level is asymptotically decreased to zero. The interface pattern thus appears as a bandlike pattern of alternate liquid and vapor phases, a puzzling phenomenon that was observed with CO2 and H2 near their critical point in weightlessness [Acta Astron. 61 1002 (2007); Europhys. Lett. 86 16003 (2009)].

Climatology of tracked persistent maxima of 500-hPa geopotential height

NASA Astrophysics Data System (ADS)

Liu, Ping; Zhu, Yuejian; Zhang, Qin; Gottschalck, Jon; Zhang, Minghua; Melhauser, Christopher; Li, Wei; Guan, Hong; Zhou, Xiaqiong; Hou, Dingchen; Peña, Malaquias; Wu, Guoxiong; Liu, Yimin; Zhou, Linjiong; He, Bian; Hu, Wenting; Sukhdeo, Raymond

2017-10-01

Persistent open ridges and blocking highs (maxima) of 500-hPa geopotential height (Z500; PMZ) adjacent in space and time are identified and tracked as one event with a Lagrangian objective approach to derive their climatological statistics with some dynamical reasoning. A PMZ starts with a core that contains a local eddy maximum of Z500 and its neighboring grid points whose eddy values decrease radially to about 20 geopotential meters (GPMs) smaller than the maximum. It connects two consecutive cores that share at least one grid point and are within 10° of longitude of each other using an intensity-weighted location. The PMZ ends at the core without a successor. On each day, the PMZ impacts an area of grid points contiguous to the core and with eddy values decreasing radially to 100 GPMs. The PMZs identified and tracked consist of persistent ridges, omega blockings and blocked anticyclones either connected or as individual events. For example, the PMZ during 2-13 August 2003 corresponds to persistent open ridges that caused the extreme heatwave in Western Europe. Climatological statistics based on the PMZs longer than 3 days generally agree with those of blockings. In the Northern Hemisphere, more PMZs occur in DJF season than in JJA and their duration both exhibit a log-linear distribution. Because more omega-shape blocking highs and open ridges are counted, the PMZs occur more frequently over Northeast Pacific than over Atlantic-Europe during cool seasons. Similar results are obtained using the 200-hPa geopotential height (in place of Z500), indicating the quasi-barotropic nature of the PMZ.

Electrical servo actuator bracket. [fuel control valves on jet engines

NASA Technical Reports Server (NTRS)

Sawyer, R. V. (Inventor)

1981-01-01

An electrical servo actuator is mounted on a support arm which is allowed to pivot on a bolt through a fixed mounting bracket. The actuator is pivotally connected to the end of the support arm by a bolt which has an extension allowed to pass through a slot in the fixed mounting bracket. An actuator rod extends from the servo actuator to a crank arm which turns a control shaft. A short linear thrust of the rod pivots the crank arm through about 90 for full-on control with the rod contracted into the servo actuator, and full-off control when the rod is extended from the actuator. A spring moves the servo actuator and actuator rod toward the control crank arm once the actuator rod is fully extended in the full-off position. This assures the turning of the control shaft to a full-off position. A stop bolt and slot are provided to limit pivot motion. Once fully extended, the spring pivots the motion.

European Marketing Authorizations Granted Based on a Single Pivotal Clinical Trial: The Rule or the Exception?

PubMed

Morant, Anne Vinther; Vestergaard, Henrik Tang

2018-07-01

A minimum of two positive, adequate, and well-controlled clinical trials has historically been the gold standard for providing substantial evidence to support regulatory approval of a new medicine. Nevertheless, the present analysis of European Marketing Authorizations granted between 2012 and 2016 showed that 45% of new active substances were approved based on a single pivotal clinical trial. For therapeutic areas such as oncology and cardiovascular diseases, approvals based on a single pivotal trial are the rule rather than the exception, whereas new medicines within the nervous system area were generally supported by two or more pivotal trials. While overall similar trends have been observed in the US, the recent US Food and Drug Administration approvals of nervous system medicines based on a single pivotal trial suggest that a case-by-case scientific evaluation of the totality of evidence is increasingly applied to facilitate faster access of new medicines to patients suffering from serious diseases. © 2017 American Society for Clinical Pharmacology and Therapeutics.

PIVOT: platform for interactive analysis and visualization of transcriptomics data.

PubMed

Zhu, Qin; Fisher, Stephen A; Dueck, Hannah; Middleton, Sarah; Khaladkar, Mugdha; Kim, Junhyong

2018-01-05

Many R packages have been developed for transcriptome analysis but their use often requires familiarity with R and integrating results of different packages requires scripts to wrangle the datatypes. Furthermore, exploratory data analyses often generate multiple derived datasets such as data subsets or data transformations, which can be difficult to track. Here we present PIVOT, an R-based platform that wraps open source transcriptome analysis packages with a uniform user interface and graphical data management that allows non-programmers to interactively explore transcriptomics data. PIVOT supports more than 40 popular open source packages for transcriptome analysis and provides an extensive set of tools for statistical data manipulations. A graph-based visual interface is used to represent the links between derived datasets, allowing easy tracking of data versions. PIVOT further supports automatic report generation, publication-quality plots, and program/data state saving, such that all analysis can be saved, shared and reproduced. PIVOT will allow researchers with broad background to easily access sophisticated transcriptome analysis tools and interactively explore transcriptome datasets.

Computer-aided teniae coli detection using height maps from computed tomographic colonography images

NASA Astrophysics Data System (ADS)

Wei, Zhuoshi; Yao, Jianhua; Wang, Shijun; Summers, Ronald M.

2011-03-01

Computed tomographic colonography (CTC) is a minimally invasive technique for colonic polyps and cancer screening. Teniae coli are three bands of longitudinal smooth muscle on the colon surface. They are parallel, equally distributed on the colon wall, and form a triple helix structure from the appendix to the sigmoid colon. Because of their characteristics, teniae coli are important anatomical meaningful landmarks on human colon. This paper proposes a novel method for teniae coli detection on CT colonography. We first unfold the three-dimensional (3D) colon using a reversible projection technique and compute the two-dimensional (2D) height map of the unfolded colon. The height map records the elevation of colon surface relative to the unfolding plane, where haustral folds corresponding to high elevation points and teniae to low elevation points. The teniae coli are detected on the height map and then projected back to the 3D colon. Since teniae are located where the haustral folds meet, we break down the problem by first detecting haustral folds. We apply 2D Gabor filter banks to extract fold features. The maximum response of the filter banks is then selected as the feature image. The fold centers are then identified based on piecewise thresholding on the feature image. Connecting the fold centers yields a path of the folds. Teniae coli are finally extracted as lines running between the fold paths. Experiments were carried out on 7 cases. The proposed method yielded a promising result with an average normalized RMSE of 5.66% and standard deviation of 4.79% of the circumference of the colon.

3-D optical profilometry at micron scale with multi-frequency fringe projection using modified fibre optic Lloyd's mirror technique

NASA Astrophysics Data System (ADS)

Inanç, Arda; Kösoğlu, Gülşen; Yüksel, Heba; Naci Inci, Mehmet

2018-06-01

A new fibre optic Lloyd's mirror method is developed for extracting 3-D height distribution of various objects at the micron scale with a resolution of 4 μm. The fibre optic assembly is elegantly integrated to an optical microscope and a CCD camera. It is demonstrated that the proposed technique is quite suitable and practical to produce an interference pattern with an adjustable frequency. By increasing the distance between the fibre and the mirror with a micrometre stage in the Lloyd's mirror assembly, the separation between the two bright fringes is lowered down to the micron scale without using any additional elements as part of the optical projection unit. A fibre optic cable, whose polymer jacket is partially stripped, and a microfluidic channel are used as test objects to extract their surface topographies. Point by point sensitivity of the method is found to be around 8 μm, changing a couple of microns depending on the fringe frequency and the measured height. A straightforward calibration procedure for the phase to height conversion is also introduced by making use of the vertical moving stage of the optical microscope. The phase analysis of the acquired image is carried out by One Dimensional Continuous Wavelet Transform for which the chosen wavelet is the Morlet wavelet and the carrier removal of the projected fringe patterns is achieved by reference subtraction. Furthermore, flexible multi-frequency property of the proposed method allows measuring discontinuous heights where there are phase ambiguities like 2π by lowering the fringe frequency and eliminating the phase ambiguity.

Storm Surge of Supertyphoon Haiyan (7-9 Nov 2013) on Samar (Philippines) Moved the Largest Boulder Ever Documented for a Recent Storm

NASA Astrophysics Data System (ADS)

Engel, M.; May, S. M.; Brill, D.; Reyes, M.; Brückner, H.

2014-12-01

Supertyphoon Haiyan (local name: Yolanda) struck the Philippines on 7-9 Nov 2013. It constantly reached category 5 (SSH scale) during its crossing of the archipelago. Storm surge heights of more than 7 m, wave heights of up to 5 m, and extensive flooding along the coast are reported. The death toll surpassed 6,000 individuals, and more than 16 M people were affected in total. The massive storm surge, which surprised many residents in particular on Samar and Leyte, also initiated the dislocation of large boulders at the coastline of SE Samar. Since such deposits may indicate maximum flooding distances and flow velocities of extreme wave events over timescales exceeding the era of historical documentation, they have increasingly been explored as a source for coastal hazard assessment. However, there is no clear consensus on differences in transport capacities and boulder field patterns created by storms and tsunamis. Thus, records from recent events provide a pivotal reference for process-related interpretation of other coastal boulder fields. We conducted a geomorphological and sedimentological survey after Haiyan on Leyte, Samar, Negros, and Bantayan. In SE Samar, the largest boulder (~75 m³; 9.0 x 4.5 x 3.5 m³; ~180 t) was shifted for 45 m on an inclined upper intertidal platform behind a Holocene reef by longshore sliding. A clast of ~70 t was moved by saltation and/or rolling for the same distance. A boulder of ~23.5 t was quarried at 2 m a.s.l. (above mean sea level) from the cliff edge of the Pleistocene carbonate platform and transported to a position of 6 m a.s.l. Boulders of up to ~17 t were moved from 6.5 to 10 m a.s.l., 2 m below the highest flood marks. Volumes of the limestone boulders were calculated using DGPS-derived point clouds transferred to ArcGIS. Densities were estimated to be around 2.3 g cm-3 using rock samples and the Archimedean principle. Downward-facing rock pools, grass patches, living barnacles, roots and soil staining on exposed former bottom sides, and fresh wood jammed under the rocks provide unambiguous evidence for subrecent transport and overturning. We conclude that the geological legacy of Haiyan calls for a careful reconsideration of possible storm surge transport where boulders, based on their size, have previously been associated with tsunami impacts and storms have been ruled out to be the cause.

Local variation of inundation, sedimentary characteristics, and mineral assemblages of the 2011 Tohoku-oki tsunami on the Misawa coast, Aomori, Japan

NASA Astrophysics Data System (ADS)

Nakamura, Yugo; Nishimura, Yuichi; Putra, Purna Sulastya

2012-12-01

The 2011 Tohoku-oki tsunami caused severe damage to the coastal regions of eastern Japan and left a sediment veneer over affected areas. We discuss differences in depositional characteristics of the 2011 Tohoku-oki tsunami from the viewpoint of the sediment source, coastal topography and flow height. The study area on the Misawa coast, northern Tohoku, includes a 20 km long coastline with sandy beaches, coastal dunes and a gently sloping lowland. This landscape assemblage provides an opportunity to examine the effects of topography on the characteristics of the tsunami deposit. During field surveys conducted from April 10 to May 2, 2011, we described the thickness, facies, and structure of the tsunami deposit. We also collected sand samples at approximately 20 m intervals along 13 shore-perpendicular transects extending up to 550 m inland, for grain size and mineral assemblage analysis. The tsunami flow height was estimated by measuring the elevation of debris found in trees, broken tree limbs, or water marks on buildings. The nature of the coastal lowland affected the flow height and inundation distance. In the southern part of the study area, where there is a narrow, 100 m wide low-lying coastal strip, the run-up height reached 10 m on the landward terrace slopes. To the north, the maximum inundation reached 550 m with a run-up height of 3.2 m on the wider, low-lying coastal topography. The average flow height was 4-5 m. The tsunami eroded coastal dunes and formed small scarps along the coast. Immediately landward of the coastal dunes the tsunami deposit was more than 20 cm thick, but thinned markedly inland from this point. Close to the dunes the deposit was composed largely of medium sand (1-2 Φ) with planar and parallel bedding, but with no apparent upward fining or coarsening. The grain size was similar to that of the coastal dune and we infer that the dunes were the local source material for the tsunami deposit at this point. The mineral assemblage of the tsunami deposit was dominated by orthopyroxene and clinopyroxene and was also similar to the dune and beach sand. At sites more than half the inundation distance inland, the thinner tsunami deposit consisted mainly of fine sand (2.375 Φ) with some upward fining. The difference in grain size and sedimentary characteristics was probably caused by differences in sediment transportation and depositional processes. We infer that the well-sorted, finer sediments were deposited out of suspension, whereas the relatively coarse sands were laid down from traction flows. The depositional characteristics of the 2011 Tohoku-oki tsunami deposit appeared to have been affected mainly by the coastal topography and the extent of erosion at any one point, as opposed to flow height.

Performance evaluation of FSO system using wavelength and time diversity over malaga turbulence channel with pointing errors

NASA Astrophysics Data System (ADS)

Balaji, K. A.; Prabu, K.

2018-03-01

There is an immense demand for high bandwidth and high data rate systems, which is fulfilled by wireless optical communication or free space optics (FSO). Hence FSO gained a pivotal role in research which has a added advantage of both cost-effective and licence free huge bandwidth. Unfortunately the optical signal in free space suffers from irradiance and phase fluctuations due to atmospheric turbulence and pointing errors which deteriorates the signal and degrades the performance of communication system over longer distance which is undesirable. In this paper, we have considered polarization shift keying (POLSK) system applied with wavelength and time diversity technique over Malaga(M)distribution to mitigate turbulence induced fading. We derived closed form mathematical expressions for estimating the systems outage probability and average bit error rate (BER). Ultimately from the results we can infer that wavelength and time diversity schemes enhances these systems performance.

[Working conditions for supermarket employees: from experimental data to best practices].

PubMed

Martellotta, Francesco; Della Crociata, Sabrina; Simone, Antonio; Calderoni, Leonardo; D'Alba, Michele; Cervellati, Massimo; Papapietro, Nunzio

2014-07-15

Thermal, acoustic and visual comfort conditions for hypermarket workers have never been investigated with scientific methods. taking advantage of a case study, with characteristics capable of generalizing the results, analytically measure the actual comfort conditions to which workers are exposed and point out possible ameliorative proposals. Carry out a detailed survey based on instrumental measurements combined with subjective questionnaires to assess the indoor environment. Even though the analysis pointed out no significant risk conditions, several smaller problems appeared in terms of local discomfort (such as cold limbs, higher sound level exposure, limited glare phenomena) for cashier workers. The origin of these problems appeared to be the pivotal position of the cash registers. Taking into account observed phenomena and their causes a list of "best practices" has been defined hoping that their adoption could further limit any impact on workers comfort conditions.

Asymmetric Thrust Reversers

NASA Technical Reports Server (NTRS)

Chandler, Jesse M. (Inventor); Suciu, Gabriel L. (Inventor)

2018-01-01

An aircraft includes a propulsion supported within an aft portion of a fuselage A thrust reverser is mounted in the aft portion of the fuselage proximate the propulsion system for directing thrust in a direction to slow the aircraft. The thrust reverser includes an upper blocker door movable about a first pivot axis to a deployed position and a lower blocker door movable about a second pivot axis not parallel to the first pivot axis.

27. VIEW NORTHWEST FROM DECKING ON SOUTHEAST CORNER OF PIVOT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

27. VIEW NORTHWEST FROM DECKING ON SOUTHEAST CORNER OF PIVOT PIER, DRIVE SYSTEM FOR SWING-SPAN INCLUDES: (from left to right) WEDGE DRIVE GEAR BOX, SHAFTS TO WEDGE DRIVE DRIVE, WEDGE DRIVE CRANK SHAFTS, ELECTRIC MOTOR, INTERNATIONAL HARVESTER GASOLINE ENGINE, CONTROL RODS FOR STARTING AND CHOKING ENGINE, PIVOT (bottom center), AND TRACK ON CONCRETE PIER - Tipers Bridge, Spanning Great Wicomico River at State Route 200, Kilmarnock, Lancaster County, VA

A proposed cutoff point of waist-to-height ratio for metabolic risk in African township adolescents.

PubMed

Kruger, H Salome; Faber, Mieke; Schutte, Aletta E; Ellis, Suria M

2013-03-01

A waist:height ratio (WHtR) higher than 0.5 has been proposed as a cutoff point for abdominal obesity in both sexes and at all ages. It is unknown if this cutoff point is appropriate for previously undernourished adolescents. We assessed the cutoff value of the WHtR associated with an increased metabolic risk in 178 black South African 14- to 18-y-old adolescents (69 boys, 109 girls). We measured weight, height, waist circumference, fasting plasma glucose and insulin levels, serum high-sensitivity C-reactive protein, and blood pressure and calculated the WHtR and homeostasis model assessment of insulin resistance (HOMA-IR). Using receiver operating characteristics curve analyses, we assessed the WHtR with the highest sensitivity and specificity to discriminate adolescents with increased fasting plasma glucose, HOMA-IR, serum high-sensitivity C-reactive protein, and blood pressure from those with "normal" values. The WHtR cutoff points derived from the receiver operating characteristics curves ranged from 0.40 to 0.41, with best diagnostic value at 0.41. A WHtR of 0.40 had 80% sensitivity and 38.5% specificity to classify adolescents with fasting blood glucose level higher than 5.6 mmol/L (area under the curve [AUC] 0.57). A WHtR of 0.41 had 64% sensitivity and 58.5% specificity for a HOMA-IR higher than 3.4 (AUC 0.66), 55% sensitivity and 55.6% specificity for a high-sensitivity C-reactive protein level higher than 1 mg/L (AUC 0.57), and 64% sensitivity and 50.2% specificity for a blood pressure higher than the age-, sex-, and height-specific 90th percentiles (AUC 0.56). Adolescents with a WHtR higher than 0.41 had an odds ratio of 2.46 (95% confidence interval 0.96-6.30) for having a HOMA-IR higher than 3.4. The WHtR cutoff to indicate metabolic risk for black South African adolescents is 0.41, which is lower than the proposed international cutoff of 0.5. The WHtR can be used for screening adolescents with components of the metabolic syndrome in intervention programs. Copyright © 2013 Elsevier Inc. All rights reserved.

Uav-Based Automatic Tree Growth Measurement for Biomass Estimation

NASA Astrophysics Data System (ADS)

Karpina, M.; Jarząbek-Rychard, M.; Tymków, P.; Borkowski, A.

2016-06-01

Manual in-situ measurements of geometric tree parameters for the biomass volume estimation are time-consuming and economically non-effective. Photogrammetric techniques can be deployed in order to automate the measurement procedure. The purpose of the presented work is an automatic tree growth estimation based on Unmanned Aircraft Vehicle (UAV) imagery. The experiment was conducted in an agriculture test field with scots pine canopies. The data was collected using a Leica Aibotix X6V2 platform equipped with a Nikon D800 camera. Reference geometric parameters of selected sample plants were measured manually each week. In situ measurements were correlated with the UAV data acquisition. The correlation aimed at the investigation of optimal conditions for a flight and parameter settings for image acquisition. The collected images are processed in a state of the art tool resulting in a generation of dense 3D point clouds. The algorithm is developed in order to estimate geometric tree parameters from 3D points. Stem positions and tree tops are identified automatically in a cross section, followed by the calculation of tree heights. The automatically derived height values are compared to the reference measurements performed manually. The comparison allows for the evaluation of automatic growth estimation process. The accuracy achieved using UAV photogrammetry for tree heights estimation is about 5cm.

Global Positioning System Antenna Fixed Height Tripod Adapter

NASA Technical Reports Server (NTRS)

Dinardo, Steven J.; Smith, Mark A.

1997-01-01

An improved Global Positioning em antenna adaptor allows fixed antenna height measurements by removably attaching an adaptor plate to a conventional surveyor's tripod. Antenna height is controlled by an antenna boom which is a fixed length rod. The antenna is attached to one end of the boom. The opposite end of the boom tapers to a point sized to fit into a depression at the center of survey markers. The boom passes through the hollow center of a universal ball joint which is mounted at the center of the adaptor plate so that the point of the rod can be fixed in the marker's central depression. The mountains of the ball joint allow the joint to be moved horizontally in any direction relative to the tripod. When the ball joint is moved horizontally, the angle between the boom and the vertical changes because the boom's position is fixed at its lower end. A spirit level attached to the rod allows an operator to determine when the boom is plumb. The position of the ball joint is adjusted horizontally until the boom is plumb. At that time the antenna is positioned exactly over the center of the monument and the elevation of the antenna is precisely set by the length of the boom.

Effect of Latent Myofascial Trigger Points on Strength Measurements of the Upper Trapezius: A Case-Controlled Trial

PubMed Central

Anshul

2011-01-01

ABSTRACT Purpose: The purpose of this article was to determine whether strength is altered in the upper trapezius in the presence of latent myofascial trigger points (MTrP). Methods: This study was case controlled and used convenience sampling. The sample recruited was homogeneous with respect to age, sex, height, and body mass. Participants were assessed for the presence of latent MTrP in the upper trapezius and placed into two groups: an experimental group that had latent MTrP in the upper trapezius and a control group that did not. Eighteen women (mean age 21.4 y, SD 1.89; mean height 156.9 cm, SD 4.03; and mean body mass 51.7 kg, SD 5.84) made up the experimental group, and 19 women (mean age 20.3 y, SD 1.86; mean height 158.6 cm, SD 3.14; and mean body mass 53.2 kg, SD 5.17) made up the control group. We obtained strength measurements of the non-dominant arm using a handheld dynamometer and compared them between the two groups. Results: The difference in the strength measurements between the two groups was not statistically significant (p=0.59). Conclusions: The presence of latent MTrPs may not affect the strength of the upper trapezius. PMID:22942517

Transcriptome profiling during a natural host-parasite interaction.

PubMed

McTaggart, Seanna J; Cézard, Timothée; Garbutt, Jennie S; Wilson, Phil J; Little, Tom J

2015-08-28

Infection outcome in some coevolving host-pathogens is characterised by host-pathogen genetic interactions, where particular host genotypes are susceptible only to a subset of pathogen genotypes. To identify candidate genes responsible for the infection status of the host, we exposed a Daphnia magna host genotype to two bacterial strains of Pasteuria ramosa, one of which results in infection, while the other does not. At three time points (four, eight and 12 h) post pathogen exposure, we sequenced the complete transcriptome of the hosts using RNA-Seq (Illumina). We observed a rapid and transient response to pathogen treatment. Specifically, at the four-hour time point, eight genes were differentially expressed. At the eight-hour time point, a single gene was differentially expressed in the resistant combination only, and no genes were differentially expressed at the 12-h time point. We found that pathogen-associated transcriptional activity is greatest soon after exposure. Genome-wide resistant combinations were more likely to show upregulation of genes, while susceptible combinations were more likely to be downregulated, relative to controls. Our results also provide several novel candidate genes that may play a pivotal role in determining infection outcomes.

Stress optimization of leaf-spring crossed flexure pivots for an active Gurney flap mechanism

NASA Astrophysics Data System (ADS)

Freire Gómez, Jon; Booker, Julian D.; Mellor, Phil H.

2015-04-01

The EU's Green Rotorcraft programme is pursuing the development of a functional and airworthy Active Gurney Flap (AGF) for a full-scale helicopter rotor blade. Interest in the development of this `smart adaptive rotor blade' technology lies in its potential to provide a number of aerodynamic benefits, which would in turn translate into a reduction in fuel consumption and noise levels. The AGF mechanism selected employs leaf-spring crossed flexure pivots. These provide important advantages over bearings as they are not susceptible to seizing and do not require maintenance (i.e. lubrication or cleaning). A baseline design of this mechanism was successfully tested both in a fatigue rig and in a 2D wind tunnel environment at flight-representative deployment schedules. For full validation, a flight test would also be required. However, the severity of the in-flight loading conditions would likely compromise the mechanical integrity of the pivots' leaf-springs in their current form. This paper investigates the scope for stress reduction through three-dimensional shape optimization of the leaf-springs of a generic crossed flexure pivot. To this end, a procedure combining a linear strain energy formulation, a parametric leaf-spring profile definition and a series of optimization algorithms is employed. The resulting optimized leaf-springs are proven to be not only independent of the angular rotation at which the pivot operates, but also linearly scalable to leaf-springs of any length, minimum thickness and width. Validated using non-linear finite element analysis, the results show very significant stress reductions relative to pivots with constant cross section leaf-springs, of up to as much as 30% for the specific pivot configuration employed in the AGF mechanism. It is concluded that shape optimization offers great potential for reducing stress in crossed flexure pivots and, consequently, for extending their fatigue life and/or rotational range.

Non-hoop winding effect on bonding temperature of laser assisted tape winding process

NASA Astrophysics Data System (ADS)

Zaami, Amin; Baran, Ismet; Akkerman, Remko

2018-05-01

One of the advanced methods for production of thermoplastic composite methods is laser assisted tape winding (LATW). Predicting the temperature in LATW process is very important since the temperature at nip-point (bonding line through width) plays a pivotal role in a proper bonding and hence the mechanical performance. Despite the hoop-winding where the nip-point is the straight line, non-hoop winding includes a curved nip-point line. Hence, the non-hoop winding causes somewhat a different power input through laser-rays and-reflections and consequently generates unknown complex temperature profile on the curved nip-point line. Investigating the temperature at the nip-point line is the point of interest in this study. In order to understand this effect, a numerical model is proposed to capture the effect of laser-rays and their reflections on the nip-point temperature. To this end, a 3D optical model considering the objects in LATW process is considered. Then, the power distribution (absorption and reflection) from the optical analysis is used as an input (heat flux distribution) for the thermal analysis. The thermal analysis employs a fully-implicit advection-diffusion model to calculate the temperature on the surfaces. The results are examined to demonstrate the effect of winding direction on the curved nip-point line (tape width) which has not been considered in literature up to now. Furthermore, the results can be used for designing a better and more efficient setup in the LATW process.

Association between Adult Height and Risk of Colorectal, Lung, and Prostate Cancer: Results from Meta-analyses of Prospective Studies and Mendelian Randomization Analyses.

PubMed

Khankari, Nikhil K; Shu, Xiao-Ou; Wen, Wanqing; Kraft, Peter; Lindström, Sara; Peters, Ulrike; Schildkraut, Joellen; Schumacher, Fredrick; Bofetta, Paolo; Risch, Angela; Bickeböller, Heike; Amos, Christopher I; Easton, Douglas; Eeles, Rosalind A; Gruber, Stephen B; Haiman, Christopher A; Hunter, David J; Chanock, Stephen J; Pierce, Brandon L; Zheng, Wei

2016-09-01

Observational studies examining associations between adult height and risk of colorectal, prostate, and lung cancers have generated mixed results. We conducted meta-analyses using data from prospective cohort studies and further carried out Mendelian randomization analyses, using height-associated genetic variants identified in a genome-wide association study (GWAS), to evaluate the association of adult height with these cancers. A systematic review of prospective studies was conducted using the PubMed, Embase, and Web of Science databases. Using meta-analyses, results obtained from 62 studies were summarized for the association of a 10-cm increase in height with cancer risk. Mendelian randomization analyses were conducted using summary statistics obtained for 423 genetic variants identified from a recent GWAS of adult height and from a cancer genetics consortium study of multiple cancers that included 47,800 cases and 81,353 controls. For a 10-cm increase in height, the summary relative risks derived from the meta-analyses of prospective studies were 1.12 (95% CI 1.10, 1.15), 1.07 (95% CI 1.05, 1.10), and 1.06 (95% CI 1.02, 1.11) for colorectal, prostate, and lung cancers, respectively. Mendelian randomization analyses showed increased risks of colorectal (odds ratio [OR] = 1.58, 95% CI 1.14, 2.18) and lung cancer (OR = 1.10, 95% CI 1.00, 1.22) associated with each 10-cm increase in genetically predicted height. No association was observed for prostate cancer (OR = 1.03, 95% CI 0.92, 1.15). Our meta-analysis was limited to published studies. The sample size for the Mendelian randomization analysis of colorectal cancer was relatively small, thus affecting the precision of the point estimate. Our study provides evidence for a potential causal association of adult height with the risk of colorectal and lung cancers and suggests that certain genetic factors and biological pathways affecting adult height may also affect the risk of these cancers.

Does Shoe Collar Height Influence Ankle Joint Kinematics and Kinetics in Sagittal Plane Maneuvers?

PubMed Central

Yang, Yang; Fang, Ying; Zhang, Xini; He, Junliang; Fu, Weijie

2017-01-01

The Objective of the study is to investigate the effects of basketball shoes with different collar heights on ankle kinematics and kinetics and athletic performance in different sagittal plane maneuvers. Twelve participants who wore high-top and low-top basketball shoes (hereafter, HS and LS, respectively) performed a weight-bearing dorsiflexion (WB-DF) maneuver, drop jumps (DJs), and lay-up jumps (LJs). Their sagittal plane kinematics and ground reaction forces were recorded using the Vicon motion capture system and Kistler force plates simultaneously. Moreover, ankle dorsiflexion and plantarflexion angles, moment, power, stiffness, and jump height were calculated. In the WB-DF test, the peak ankle dorsiflexion angle (p = 0.041) was significantly smaller in HS than in LS. Additionally, the peak ankle plantarflexion moment (p = 0.028) and power (p = 0.022) were significantly lower in HS than in LS during LJs but not during DJs. In both jumping maneuvers, no significant differences were found in the jump height or ankle kinematics between the two shoe types. According to the WB-DF test, increasing shoe collar height can effectively reduce the ankle range of motion in the sagittal plane. Although the HS did not restrict the flexion–extension performance of the ankle joint during two jumping maneuvers, an increased shoe collar height can reduce peak ankle plantarflexion moment and peak power during the push-off phase in LJs. Therefore, a higher shoe collar height should be used to circumvent effects on the partial kinetics of the ankle joint in the sagittal plane. Key points An increased shoe collar height effectively reduced ankle joint ROM in the sagittal plane in weight-bearing dorsiflexion maneuver. Shoe collar height did not affect sagittal plane ankle kinematics and had no effect on performance during realistic jumping. Shoe collar height can affect the ankle plantarflexion torque and peak power during the push-off phase in lay-up jump. PMID:29238255

Climate limits across space and time on European forest structure

NASA Astrophysics Data System (ADS)

Moreno, A. L. S.; Neumann, M.; Hasenauer, H.

2017-12-01

The impact climate has on forests has been extensively studied. However, the large scale effect climate has on forest structures, such as average diameters, heights and basal area are understudied in a spatially explicit manner. The limits, tipping points and thresholds that climate places on forest structures dictate the services a forest may provide, the vulnerability of a forest to mortality and the potential value of the timber there within. The majority of current research either investigates climate impacts on forest pools and fluxes, on a tree physiological scale or on case studies that are used to extrapolate results and potential impacts. A spatially explicit study on how climate affects forest structure over a large region would give valuable information to stakeholders who are more concerned with ecosystem services that cannot be described by pools and fluxes but require spatially explicit information - such as biodiversity, habitat suitability, and market values. In this study, we quantified the limits that climate (maximum, minimum temperature and precipitation) places on 3 forest structures, diameter at breast height, height, and basal area throughout Europe. Our results show clear climatic zones of high and low upper limits for each forest structure variable studied. We also spatially analyzed how climate restricts the potential bio-physical upper limits and creates tipping points of each forest structure variable and which climate factors are most limiting. Further, we demonstrated how the climate change has affected 8 individual forests across Europe and then the continent as a whole. We find that diameter, height and basal area are limited by climate in different ways and that areas may have high upper limits in one structure and low upper limits in another limitted by different climate variables. We also found that even though individual forests may have increased their potential upper limit forest structure values, European forests as a whole have lost, on average, 5.0%, 1.7% and 6.5% in potential mean forest diameter, height and basal area, respectively.

KNGEOID14: A national hybrid geoid model in Korea

NASA Astrophysics Data System (ADS)

Kang, S.; Sung, Y. M.; KIM, H.; Kim, Y. S.

2016-12-01

This study describes in brief the construction of a national hybrid geoid model in Korea, KNGEOID14, which can be used as an accurate vertical datum in/around Korea. The hybrid geoid model should be determined by fitting the gravimetric geoid to the geometric geoid undulations from GNSS/Leveling data which were presented the local vertical level. For developing the gravimetric geoid model, we determined all frequency parts (long, middle and short-frequency) of gravimetric geoid using all available data with optimal remove-restore technique based on EGM2008 reference surface. In remove-restore technique, the EGM2008 model to degree 360, RTM reduction method were used for calculating the long, middle and short-frequency part of gravimetric geoid, respectively. A number of gravity data compiled for modeling the middle-frequency part, residual geoid, containing 8,866 points gravity data on land and ocean areas. And, the DEM data gridded by 100m×100m were used for short-frequency part, is the topographic effect on the geoid generated by RTM method. The accuracy of gravimetric geoid model were evaluated by comparison with GNSS/Leveling data was about -0.362m ± 0.055m. Finally, we developed the national hybrid geoid model in Korea, KNGEOID14, corrected to gravimetric geoid with the correction term by fitting the about 1,200 GNSS/Leveling data on Korean bench marks. The correction term is modeled using the difference between GNSS/Leveling derived geoidal heights and gravimetric geoidal heights. The stochastic model used in the calculation of correction term is the LSC technique based on second-order Markov covariance function. The post-fit error (mean and std. dev.) of the KNGEOID14 model was evaluated as 0.001m ± 0.033m. Concerning the result of this study, the accurate orthometric height at any points in Korea will be easily and precisely calculated by combining the geoidal height from KNGEOID14 and ellipsoidal height from GPS observation technique.

Discriminating crop, weeds and soil surface with a terrestrial LIDAR sensor.

PubMed

Andújar, Dionisio; Rueda-Ayala, Victor; Moreno, Hugo; Rosell-Polo, Joan Ramón; Escolá, Alexandre; Valero, Constantino; Gerhards, Roland; Fernández-Quintanilla, César; Dorado, José; Griepentrog, Hans-Werner

2013-10-29

In this study, the evaluation of the accuracy and performance of a light detection and ranging (LIDAR) sensor for vegetation using distance and reflection measurements aiming to detect and discriminate maize plants and weeds from soil surface was done. The study continues a previous work carried out in a maize field in Spain with a LIDAR sensor using exclusively one index, the height profile. The current system uses a combination of the two mentioned indexes. The experiment was carried out in a maize field at growth stage 12-14, at 16 different locations selected to represent the widest possible density of three weeds: Echinochloa crus-galli (L.) P.Beauv., Lamium purpureum L., Galium aparine L.and Veronica persica Poir.. A terrestrial LIDAR sensor was mounted on a tripod pointing to the inter-row area, with its horizontal axis and the field of view pointing vertically downwards to the ground, scanning a vertical plane with the potential presence of vegetation. Immediately after the LIDAR data acquisition (distances and reflection measurements), actual heights of plants were estimated using an appropriate methodology. For that purpose, digital images were taken of each sampled area. Data showed a high correlation between LIDAR measured height and actual plant heights (R2 = 0.75). Binary logistic regression between weed presence/absence and the sensor readings (LIDAR height and reflection values) was used to validate the accuracy of the sensor. This permitted the discrimination of vegetation from the ground with an accuracy of up to 95%. In addition, a Canonical Discrimination Analysis (CDA) was able to discriminate mostly between soil and vegetation and, to a far lesser extent, between crop and weeds. The studied methodology arises as a good system for weed detection, which in combination with other principles, such as vision-based technologies, could improve the efficiency and accuracy of herbicide spraying.