30 CFR 582.25 - Plan modification.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Plan modification. 582.25 Section 582.25 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE... of Lessees § 582.25 Plan modification. Approved Delineation, Testing, and Mining Plans may be...

Texture Modification of the Shuttle Landing Facility Runway at Kennedy Space Center

NASA Technical Reports Server (NTRS)

Daugherty, Robert H.; Yager, Thomas J.

1997-01-01

This paper describes the test procedures and the criteria used in selecting an effective runway-surface-texture modification at the Kennedy Space Center (KSC) Shuttle Landing Facility (SLF) to reduce Orbiter tire wear. The new runway surface may ultimately result in an increase of allowable crosswinds for launch and landing operations. The modification allows launch and landing operations in 20-knot crosswinds, if desired. This 5-knot increase over the previous 15-knot limit drastically increases landing safety and the ability to make on-time launches to support missions in which Space Station rendezvous are planned. The paper presents the results of an initial (1988) texture modification to reduce tire spin-up wear and then describes a series of tests that use an instrumented ground-test vehicle to compare tire friction and wear characteristics, at small scale, of proposed texture modifications placed into the SLF runway surface itself. Based on these tests, three candidate surfaces were chosen to be tested at full-scale by using a highly modified and instrumented transport aircraft capable of duplicating full Orbiter landing profiles. The full-scale Orbiter tire testing revealed that tire wear could be reduced approximately by half with either of two candidates. The texture-modification technique using a Humble Equipment Company Skidabrader(trademark) shotpeening machine proved to be highly effective, and the entire SLF runway surface was modified in September 1994. The extensive testing and evaluation effort that preceded the selection of this particular surface-texture-modification technique is described herein.

7 CFR 1415.12 - Modifications to easements and rental contracts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... modifications for restoration agreements and grazing management plans, or conservation plans where applicable... conservation plans, grazing management plans, and restoration plans, to facilitate the practical administration...

Langley Research Center's Unitary Plan Wind Tunnel: Testing Capabilities and Recent Modernization Activities

NASA Technical Reports Server (NTRS)

Micol, John R.

2001-01-01

Description, capabilities, initiatives, and utilization of the NASA Langley Research Center's Unitary Plan Wind Tunnel are presented. A brief overview of the facility's operational capabilities and testing techniques is provided. A recent Construction of Facilities (CoF) project to improve facility productivity and efficiency through facility automation has been completed and is discussed. Several new and maturing thrusts are underway that include systematic efforts to provide credible assessment for data quality, modifications to the new automation control system for increased compatibility with the Modern Design Of Experiments (MDOE) testing methodology, and process improvements for better test coordination, planning, and execution.

Langley Research Center's Unitary Plan Wind Tunnel: Testing Capabilities and Recent Modernization Activities

NASA Technical Reports Server (NTRS)

Micol, John R.

2001-01-01

Description, capabilities, initiatives, and utilization of the NASA Langley Research Center's Unitary Plan Wind Tunnel are presented. A brief overview of the facility's operational capabilities and testing techniques is provided. A recent Construction of Facilities (Car) project to improve facility productivity and efficiency through facility automation has been completed and is discussed. Several new and maturing thrusts are underway that include systematic efforts to provide credible assessment for data quality, modifications to the new automation control system for increased compatibility with the Modern Design of Experiments (MDOE) testing methodology, and process improvements for better test coordination, planning, and execution.

AI-MSG modification work plan. [LMFBR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Page, J.P.

1973-08-20

This document contains the Work Plan for the modification of the AI Steam Generator for tests in Large Leak Test Rig. This Work Plan describes the objectives, scope of work, schedule and manpower, end items, and meetings and reports required for the modification.

Meter shop equipment, techniques, and operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, R.F.

1995-12-01

The development of new equipment inevitably results in new techniques and operational procedures to be implemented. Innovative techniques can result in operational changes and the development of new equipment. An operational modification opens the door for the development of new ideas, new equipment, and new techniques. This constant cycle of change promotes a continuous series of economic evaluations and decisions. Equipment and technological changes in measuring natural gas have resulted in modifications from past practices. The changes underway today will influence the way we plan and budget for the future, and, most notably, will change the way we repair gasmore » meters. The meter shop of today will need to look at the way that these changes will become available and how they will help efforts in reducing costs and increasing productivity. For instance, the standard three- and four-chambered diaphragm gas meter design has not been significantly changed in the past few decades aside from having heavy, cast iron bodies changed to lightweight aluminum bodies and utilizing a few plastic parts. But changes have been made, and more are on the threshold.« less

7 CFR 625.13 - Modification of the HFRP restoration plan.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 6 2010-01-01 2010-01-01 false Modification of the HFRP restoration plan. 625.13... CONSERVATION SERVICE, DEPARTMENT OF AGRICULTURE WATER RESOURCES HEALTHY FORESTS RESERVE PROGRAM § 625.13 Modification of the HFRP restoration plan. Consistent with the easement and applicable law, the State...

[Adherence and fidelity in patients treated with intragastric balloon].

PubMed

Mazure, R A; Cancer, E; Martínez Olmos, M A; De Castro, M L; Abilés, V; Abilés, J; Bretón, I; Álvarez, V; Peláez, N; Culebras, J M

2014-01-01

A correct treatment of obesity needs a program of habits modification regardless of the selected technique, especially if it is minimally invasive as the intragastric balloon (BIG). The adherence of the obese patients with regard to recommended drugs measures to medium- and long-term is less than 50%. Given that the results obtained using the technique of gastric balloon must be seen influenced by adherence to the modification of habits program and its fulfillment, we reviewed series published in attention to the program proposed with the BIG. The series published to date provide few details about the used Therapeutic Programs as well as the adherence of patients to them, and even less concerning the Monitoring Plan and the loyalty of the patient can be seen. We conclude the convenience to agree on a follow-up strategy, at least the 6 months during which the BIG remain in the stomach.

Behavior modification techniques used to prevent gestational diabetes: a systematic review of the literature.

PubMed

Skouteris, Helen; Morris, Heather; Nagle, Cate; Nankervis, Alison

2014-04-01

The prevalence of gestational diabetes mellitus (GDM) and obesity is increasing in developed countries, presenting significant challenges to acute care and public health. The aim of this study is to systematically review published controlled trials evaluating behavior modification interventions to prevent the development of GDM. Nine studies were identified involving such techniques as repetition of information, use of verbal and written educational information, goal setting, and planning, in addition to group and individual counseling sessions. Of the 3 trials with GDM incidence as a primary outcome, only 1 showed a significant reduction. GDM was a secondary outcome in 6 studies where the prevention of excessive gestational weight gain was the primary outcome and only 1 trial study determined an effective intervention. The small number of effective interventions highlights a significant gap in evidence to inform maternity health policy and practice.

Test plan for performance testing of the Eaton AC-3 electric vehicle

NASA Astrophysics Data System (ADS)

Crumley, R.; Heiselmann, H. W.

1985-04-01

An alternating current (ac) propulsion system for an electric vehicle was developed and tested. The test bed vehicle is a modified 1981 Mercury Lynx. The test plan was prepared specifically for the third modification to this test bed and identified as the Eaton AC-3. The scope of the testing done on the Eaton AC-3 includes coastdown and dynamometer tests but does not include environmental, on-road, or track testing. Coastdown testing is performed in accordance with SAE J-1263 (SAE Recommended Practice for Road Load Measurement and Dynamometer Simulation Using Coastdown Techniques).

30 CFR 746.18 - Mining plan modification.

Code of Federal Regulations, 2010 CFR

2010-07-01

... reclamation plan that would result in a change in the postmining land use where the surface is federally-owned. ... the Act; (2) Any change which would adversely affect the level of protection afforded any land... LANDS PROGRAM REVIEW AND APPROVAL OF MINING PLANS § 746.18 Mining plan modification. (a) Mining plan...

20 CFR 628.426 - Disapproval or revocation of the plan.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Disapproval or revocation of the plan. (a) If the Governor disapproves the SDA job training plan or plan... training plan or modification may be appealed by the PIC and chief elected official(s) of the SDA to the... and chief elected official(s) of the final disapproval of the SDA job training plan or modification...

Interdisciplinary approach for somatoprosthetic rehabilitation of a patient with clino-syndactyly and unusual dermatoglyphics.

PubMed

Aggarwal, Himanshi; Singh, Saumyendra Vikram; Singh, Arun K; Kumar, Pradeep; Singh, Balendra P

2016-12-01

Traumatic injuries are the most common cause of finger amputations. Therapeutic amputations are less common but may be essential in some patients with congenital malformations of digits. A 21-year-old female patient reported for esthetic management of malformed middle and ring finger of right hand. Examination revealed clino-syndactyly with unusual dermatoglyphics. She was successfully rehabilitated by collaborative efforts of plastic surgeon and prosthodontist, by therapeutic amputation with surgical recontouring and fabrication of somatoprosthesis. The patient was satisfied with esthetics of the prosthesis and somatoprosthesis improved function. At 6-month recall, no alterations or repair of prosthesis was required. Individualized treatment planning with integration of modifications involving a multidisciplinary approach is required to meet needs of patients with congenital digital malformations. The duplication of unusual dermatoglyphics made the prosthesis more realistic. An individualized treatment plan with modifications to conventional techniques is required to cater to rehabilitative needs of patients with congenital digital malformations. © The International Society for Prosthetics and Orthotics 2016.

48 CFR 2.101 - Definitions

Code of Federal Regulations, 2012 CFR

2012-10-01

... research, planning, development, design, construction, alteration, or repair of real property; and (3..., evaluations, consultations, comprehensive planning, program management, conceptual designs, plans and... whether a modification is minor include the value and size of the modification and the comparative value...

20 CFR 628.425 - Review and approval.

Code of Federal Regulations, 2010 CFR

2010-04-01

... or disapproval of the SDA job training plan and plan modifications that shall be provided to the SDA... the Act, the Governor shall approve the SDA job training plan or plan modification. The notice of... Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF LABOR PROGRAMS UNDER TITLE II OF...

24 CFR 401.460 - Modification or refinancing of first mortgage.

Code of Federal Regulations, 2013 CFR

2013-04-01

... modification under the Restructuring Plan. The debt service coverage used by the PAE must be adequate for... RESTRUCTURING, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT MULTIFAMILY HOUSING MORTGAGE AND HOUSING ASSISTANCE RESTRUCTURING PROGRAM (MARK-TO-MARKET) Restructuring Plan § 401.460 Modification or refinancing of first...

33 CFR 385.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE... Restoration Plan (CERP) means the plan contained in the “Final Integrated Feasibility Report and Programmatic... subsequent modification authorized in law. Comprehensive Plan Modification Report means the report prepared...

33 CFR 385.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE... Restoration Plan (CERP) means the plan contained in the “Final Integrated Feasibility Report and Programmatic... subsequent modification authorized in law. Comprehensive Plan Modification Report means the report prepared...

33 CFR 385.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE... Restoration Plan (CERP) means the plan contained in the “Final Integrated Feasibility Report and Programmatic... subsequent modification authorized in law. Comprehensive Plan Modification Report means the report prepared...

Modified lateral orbital wall decompression in Graves' orbitopathy using computer-assisted planning.

PubMed

Spalthoff, S; Jehn, P; Zimmerer, R; Rana, M; Gellrich, N-C; Dittmann, J

2018-02-01

Graves' orbitopathy, a condition seen in the autoimmune syndrome Graves' disease, affects the fatty tissue and muscles inside the orbit. Graves' orbitopathy is associated with increasing exophthalmos and sometimes leads to compressive dysthyroid optic neuropathy, resulting in progressive vision loss. Dysthyroid compressive optic neuropathy, functional problems, and cosmetic problems are the main indications for surgical decompression of the orbit, especially if conservative treatment has not led to a reduction in symptoms. Many surgical techniques are described in the literature. This article presents a modification of the lateral orbital wall osteotomy, involving the rotation and reduction of the osteotomized bone segment using preoperative planning, intraoperative computed navigation, and piezoelectric surgery. This new method combines the advantages of different techniques and appears to be a valid approach to the treatment of severe cases of Graves' orbitopathy. Copyright © 2017 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

30 CFR 282.25 - Plan modification.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false Plan modification. 282.25 Section 282.25 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT OF THE... Mining Plans may be modified upon the Director's approval of the changes proposed. When circumstances...

Conceptual design study of a Harrier V/STOL research aircraft

NASA Technical Reports Server (NTRS)

Bode, W. E.; Berger, R. L.; Elmore, G. A.; Lacey, T. R.

1978-01-01

MCAIR recently completed a conceptual design study to define modification approaches to, and derive planning prices for the conversion of a two place Harrier to a V/STOL control, display and guidance research aircraft. Control concepts such as rate damping, attitude stabilization, velocity command, and cockpit controllers are to be demonstrated. Display formats will also be investigated, and landing, navigation and guidance systems flight tested. The rear cockpit is modified such that it can be quickly adapted to faithfully simulate the controls, displays and handling qualities of a Type A or Type B V/STOL. The safety pilot always has take command capability. The modifications studied fall into two categories: basic modifications and optional modifications. Technical descriptions of the basic modifications and of the optional modifications are presented. The modification plan and schedule as well as the test plan and schedule are presented. The failure mode and effects analysis, aircraft performance, aircraft weight, and aircraft support are discussed.

Expected treatment dose construction and adaptive inverse planning optimization: Implementation for offline head and neck cancer adaptive radiotherapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan Di; Liang Jian

Purpose: To construct expected treatment dose for adaptive inverse planning optimization, and evaluate it on head and neck (h and n) cancer adaptive treatment modification. Methods: Adaptive inverse planning engine was developed and integrated in our in-house adaptive treatment control system. The adaptive inverse planning engine includes an expected treatment dose constructed using the daily cone beam (CB) CT images in its objective and constrains. Feasibility of the adaptive inverse planning optimization was evaluated retrospectively using daily CBCT images obtained from the image guided IMRT treatment of 19 h and n cancer patients. Adaptive treatment modification strategies with respect tomore » the time and the number of adaptive inverse planning optimization during the treatment course were evaluated using the cumulative treatment dose in organs of interest constructed using all daily CBCT images. Results: Expected treatment dose was constructed to include both the delivered dose, to date, and the estimated dose for the remaining treatment during the adaptive treatment course. It was used in treatment evaluation, as well as in constructing the objective and constraints for adaptive inverse planning optimization. The optimization engine is feasible to perform planning optimization based on preassigned treatment modification schedule. Compared to the conventional IMRT, the adaptive treatment for h and n cancer illustrated clear dose-volume improvement for all critical normal organs. The dose-volume reductions of right and left parotid glands, spine cord, brain stem and mandible were (17 {+-} 6)%, (14 {+-} 6)%, (11 {+-} 6)%, (12 {+-} 8)%, and (5 {+-} 3)% respectively with the single adaptive modification performed after the second treatment week; (24 {+-} 6)%, (22 {+-} 8)%, (21 {+-} 5)%, (19 {+-} 8)%, and (10 {+-} 6)% with three weekly modifications; and (28 {+-} 5)%, (25 {+-} 9)%, (26 {+-} 5)%, (24 {+-} 8)%, and (15 {+-} 9)% with five weekly modifications. Conclusions: Adaptive treatment modification can be implemented including the expected treatment dose in the adaptive inverse planning optimization. The retrospective evaluation results demonstrate that utilizing the weekly adaptive inverse planning optimization, the dose distribution of h and n cancer treatment can be largely improved.« less

43 CFR 1610.5 - Resource management plan approval, use and modification.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Resource management plan approval, use and modification. 1610.5 Section 1610.5 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR GENERAL MANAGEMENT (1000) PLANNING, PROGRAMMING...

29 CFR 2520.104b-3 - Summary of material modifications to the plan and changes in the information required to be...

Code of Federal Regulations, 2010 CFR

2010-07-01

... future must disclose a summary of that modification within 210 days after the close of the plan year in... plan, including a reduction that occurs as a result of a change in formulas, methodologies or schedules...

Collaborative Operations for Personnel Recovery

DTIC Science & Technology

2008-02-01

ADDRESS(ES) Artificial Intelligence Applications Institute The University of Edinburgh Appleton Tower, Crichton St. Edinburgh EH8 9LE, UK 8...this issue, • M is a symbol denoting a primitive plan modification activity, and • O1,…,On are plan-space objects, i.e. they are issues, nodes...of this type represents the fact that the plan-space object O was introduced into the plan as part of performing the plan modification activity M

Comparative Study of Surface Chemical Composition and Oxide Layer Modification upon Oxygen Plasma Cleaning and Piranha Etching on a Novel Low Elastic Modulus Ti25Nb21Hf Alloy

NASA Astrophysics Data System (ADS)

Paredes, Virginia; Salvagni, Emiliano; Rodríguez-Castellón, Enrique; Manero, José María

2017-08-01

Metals are widely employed for many biological artificial replacements, and it is known that the quality and the physical/chemical properties of the surface are crucial for the success of the implant. Therefore, control over surface implant materials and their elastic moduli may be crucial to avoid undesired effects. In this study, surface modification upon cleaning and activation of a low elastic modulus Ti alloy (Ti25Hf21Nb) was investigated. Two different methods, oxygen plasma (OP) cleaning and piranha (PI) solution, were studied and compared. Both surface treatments were effective for organic contaminant removal and to increase the Ti-oxide layer thickness rather than other metal-oxides present at the surface, which is beneficial for biocompatibility of the material. Furthermore, both techniques drastically increased hydrophilicity and introduced oxidation and hydroxylation (OH)-functional groups at the surface that may be beneficial for further chemical modifications. However, these treatments did not alter the surface roughness and bulk material properties. The surfaces were fully characterized in terms of surface roughness, wettability, oxide layer composition, and hydroxyl surface density through analytical techniques (interferometry, X-ray photoelectron spectroscopy (XPS), contact angle, and zinc complexation). These findings provide essential information when planning surface modifications for cleanliness, oxide layer thickness, and surface hydroxyl density, as control over these factors is essential for many applications, especially in biomaterials.

30 CFR 77.216-2 - Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements...

Code of Federal Regulations, 2013 CFR

2013-07-01

... the District Manager. (b) Any changes or modifications to plans for water, sediment, or slurry... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements; changes or modifications; certification. 77.216-2 Section...

30 CFR 77.216-2 - Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements...

Code of Federal Regulations, 2012 CFR

2012-07-01

... the District Manager. (b) Any changes or modifications to plans for water, sediment, or slurry... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements; changes or modifications; certification. 77.216-2 Section...

30 CFR 77.216-2 - Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements...

Code of Federal Regulations, 2011 CFR

2011-07-01

... the District Manager. (b) Any changes or modifications to plans for water, sediment, or slurry... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements; changes or modifications; certification. 77.216-2 Section...

30 CFR 77.216-2 - Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements...

Code of Federal Regulations, 2014 CFR

2014-07-01

... the District Manager. (b) Any changes or modifications to plans for water, sediment, or slurry... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements; changes or modifications; certification. 77.216-2 Section...

24 CFR 599.509 - Modification of commitments and plans.

Code of Federal Regulations, 2011 CFR

2011-04-01

... local commitments made at the time of application as required by § 599.107 and the tax incentives utilization plans required by § 599.505. Requests must provide evidence to support the proposed modifications...

24 CFR 599.509 - Modification of commitments and plans.

Code of Federal Regulations, 2010 CFR

2010-04-01

... local commitments made at the time of application as required by § 599.107 and the tax incentives utilization plans required by § 599.505. Requests must provide evidence to support the proposed modifications...

Bowel sparing in pediatric cranio-spinal radiotherapy: a comparison of combined electron and photon and helical TomoTherapy techniques to a standard photon method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harron, Elizabeth, E-mail: elizabeth.harron@nuh.nhs.uk; Lewis, Joanne

2012-07-01

The aim of this study was to compare the dose to organs at risk (OARs) from different craniospinal radiotherapy treatment approaches available at the Northern Centre for Cancer Care (NCCC), with a particular emphasis on sparing the bowel. Method: Treatment plans were produced for a pediatric medulloblastoma patient with inflammatory bowel disease using 3D conformal 6-MV photons (3DCP), combined 3D 6-MV photons and 18-MeV electrons (3DPE), and helical photon TomoTherapy (HT). The 3DPE plan was a modification of the standard 3DCP technique, using electrons to treat the spine inferior to the level of the diaphragm. The plans were compared inmore » terms of the dose-volume data to OARs and the nontumor integral dose. Results: The 3DPE plan was found to give the lowest dose to the bowel and the lowest nontumor integral dose of the 3 techniques. However, the coverage of the spine planning target volume (PTV) was least homogeneous using this technique, with only 74.6% of the PTV covered by 95% of the prescribed dose. HT was able to achieve the best coverage of the PTVs (99.0% of the whole-brain PTV and 93.1% of the spine PTV received 95% of the prescribed dose), but delivered a significantly higher integral dose. HT was able to spare the heart, thyroid, and eyes better than the linac-based techniques, but other OARs received a higher dose. Conclusions: Use of electrons was the best method for reducing the dose to the bowel and the integral dose, at the expense of compromised spine PTV coverage. For some patients, HT may be a viable method of improving dose homogeneity and reducing selected OAR doses.« less

Mechanisms of behavior modification in clinical behavioral medicine in China.

PubMed

Yang, Zhiyin; Su, Zhonghua; Ji, Feng; Zhu, Min; Bai, Bo

2014-08-01

Behavior modification, as the core of clinical behavioral medicine, is often used in clinical settings. We seek to summarize behavior modification techniques that are commonly used in clinical practice of behavioral medicine in China and discuss possible biobehavioral mechanisms. We reviewed common behavior modification techniques in clinical settings in China, and we reviewed studies that explored possible biobehavioral mechanisms. Commonly used clinical approaches of behavior modification in China include behavior therapy, cognitive therapy, cognitive-behavioral therapy, health education, behavior management, behavioral relaxation training, stress management intervention, desensitization therapy, biofeedback therapy, and music therapy. These techniques have been applied in the clinical treatment of a variety of diseases, such as chronic diseases, psychosomatic diseases, and psychological disorders. The biobehavioral mechanisms of these techniques involve the autonomic nervous system, neuroendocrine system, neurobiochemistry, and neuroplasticity. Behavior modification techniques are commonly used in the treatment of a variety of somatic and psychological disorders in China. Multiple biobehavioral mechanisms are involved in successful behavior modification.

Molecular PET imaging for biology-guided adaptive radiotherapy of head and neck cancer.

PubMed

Hoeben, Bianca A W; Bussink, Johan; Troost, Esther G C; Oyen, Wim J G; Kaanders, Johannes H A M

2013-10-01

Integration of molecular imaging PET techniques into therapy selection strategies and radiation treatment planning for head and neck squamous cell carcinoma (HNSCC) can serve several purposes. First, pre-treatment assessments can steer decisions about radiotherapy modifications or combinations with other modalities. Second, biology-based objective functions can be introduced to the radiation treatment planning process by co-registration of molecular imaging with planning computed tomography (CT) scans. Thus, customized heterogeneous dose distributions can be generated with escalated doses to tumor areas where radiotherapy resistance mechanisms are most prevalent. Third, monitoring of temporal and spatial variations in these radiotherapy resistance mechanisms early during the course of treatment can discriminate responders from non-responders. With such information available shortly after the start of treatment, modifications can be implemented or the radiation treatment plan can be adapted tailing the biological response pattern. Currently, these strategies are in various phases of clinical testing, mostly in single-center studies. Further validation in multicenter set-up is needed. Ultimately, this should result in availability for routine clinical practice requiring stable production and accessibility of tracers, reproducibility and standardization of imaging and analysis methods, as well as general availability of knowledge and expertise. Small studies employing adaptive radiotherapy based on functional dynamics and early response mechanisms demonstrate promising results. In this context, we focus this review on the widely used PET tracer (18)F-FDG and PET tracers depicting hypoxia and proliferation; two well-known radiation resistance mechanisms.

JESS facility modification and environmental/power plans

NASA Technical Reports Server (NTRS)

Bordeaux, T. A.

1984-01-01

Preliminary plans for facility modifications and environmental/power systems for the JESS (Joint Exercise Support System) computer laboratory and Freedom Hall are presented. Blueprints are provided for each of the facilities and an estimate of the air conditioning requirements is given.

77 FR 42462 - Hawaii State Plan for Occupational Safety and Health; Proposed Modification of 18(e) Plan Approval

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-19

... Modification of 18(e) Plan Approval AGENCY: Occupational Safety and Health Administration (OSHA), Department of... Federal Building, 90 7th Street, Suite 18-100, San Francisco, California 94103, (415) 625-2546, fax (415... INFORMATION: Background Section 18 of the Occupational Safety and Health Act of 1970 (the Act, 29 U.S.C. 667...

Biochemical Imaging of Gliomas Using MR Spectroscopic Imaging for Radiotherapy Treatment Planning

NASA Astrophysics Data System (ADS)

Heikal, Amr Ahmed

This thesis discusses the main obstacles facing wide clinical implementation of magnetic resonance spectroscopic imaging (MRSI) as a tumor delineation tool for radiotherapy treatment planning, particularly for gliomas. These main obstacles are identified as 1. observer bias and poor interpretational reproducibility of the results of MRSI scans, and 2. the long scan times required to conduct MRSI scans. An examination of an existing user-independent MRSI tumor delineation technique known as the choline-to-NAA index (CNI) is conducted to assess its utility in providing a tool for reproducible interpretation of MRSI results. While working with spatial resolutions typically twice those on which the CNI model was originally designed, a region of statistical uncertainty was discovered between the tumor and normal tissue populations and as such a modification to the CNI model was introduced to clearly identify that region. To address the issue of long scan times, a series of studies were conducted to adapt a scan acceleration technique, compressed sensing (CS), to work with MRSI and to quantify the effects of such a novel technique on the modulation transfer function (MTF), an important quantitative imaging metric. The studies included the development of the first phantom based method of measuring the MTF for MRSI data, a study of the correlation between the k-space sampling patterns used for compressed sensing and the resulting MTFs, and the introduction of a technique circumventing some of side-effects of compressed sensing by exploiting the conjugate symmetry property of k-space. The work in this thesis provides two essential steps towards wide clinical implementation of MRSI-based tumor delineation. The proposed modifications to the CNI method coupled with the application of CS to MRSI address the two main obstacles outlined. However, there continues to be room for improvement and questions that need to be answered by future research.

Flow-induced Vibration of SSME Main Injector Liquid-oxygen Posts

NASA Technical Reports Server (NTRS)

Chen, S. S.; Jendrzejczyk, J. A.; Wambsganss, M. W.

1985-01-01

The liquid-oxygen (LOX) posts are exposed to hot hydrogen flowing over the tubes on its way to the combustion chamber. Fatigue cracking of some LOX posts was observed after test firing of the SSMEs. A current design modification consists of attaching impingement shields to the LOX posts in the outer row. The modification improved the vibration/fatigue problem of the LOX posts, but resulted in an increased pressure drop that ultimately shortened the life expectancy of other components. A fundamental study of vibration of the LOX posts was initiated to understand the flow-induced vibration problem and to develop techniques to avoid detrimental vibrational effects with the overall objective of improving engine life. This effort, including an assessment of the problem, scoping calculation and experiment, and a work plan for an integrated theoretical/experimental study of the problem is summarized.

40 CFR 93.106 - Content of transportation plans and timeframe of conformity determinations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... modifications to the existing transportation network which the transportation plan envisions to be operational in the horizon years. Additions and modifications to the highway network shall be sufficiently... effect on route options between transportation analysis zones. Each added or modified highway segment...

40 CFR 93.106 - Content of transportation plans and timeframe of conformity determinations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... modifications to the existing transportation network which the transportation plan envisions to be operational in the horizon years. Additions and modifications to the highway network shall be sufficiently... effect on route options between transportation analysis zones. Each added or modified highway segment...

40 CFR 93.106 - Content of transportation plans and timeframe of conformity determinations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... modifications to the existing transportation network which the transportation plan envisions to be operational in the horizon years. Additions and modifications to the highway network shall be sufficiently... effect on route options between transportation analysis zones. Each added or modified highway segment...

40 CFR 93.106 - Content of transportation plans and timeframe of conformity determinations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... modifications to the existing transportation network which the transportation plan envisions to be operational in the horizon years. Additions and modifications to the highway network shall be sufficiently... effect on route options between transportation analysis zones. Each added or modified highway segment...

40 CFR 93.106 - Content of transportation plans and timeframe of conformity determinations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... modifications to the existing transportation network which the transportation plan envisions to be operational in the horizon years. Additions and modifications to the highway network shall be sufficiently... effect on route options between transportation analysis zones. Each added or modified highway segment...

Clinical implementation of target tracking by breathing synchronized delivery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tewatia, Dinesh; Zhang Tiezhi; Tome, Wolfgang

2006-11-15

Target-tracking techniques can be categorized based on the mechanism of the feedback loop. In real time tracking, breathing-delivery phase correlation is provided to the treatment delivery hardware. Clinical implementation of target tracking in real time requires major hardware modifications. In breathing synchronized delivery (BSD), the patient is guided to breathe in accordance with target motion derived from four-dimensional computed tomography (4D-CT). Violations of mechanical limitations of hardware are to be avoided at the treatment planning stage. Hardware modifications are not required. In this article, using sliding window IMRT delivery as an example, we have described step-by-step the implementation of targetmore » tracking by the BSD technique: (1) A breathing guide is developed from patient's normal breathing pattern. The patient tries to reproduce this guiding cycle by following the display in the goggles; (2) 4D-CT scans are acquired at all the phases of the breathing cycle; (3) The average tumor trajectory is obtained by deformable image registration of 4D-CT datasets and is smoothed by Fourier filtering; (4) Conventional IMRT planning is performed using the images at reference phase (full exhalation phase) and a leaf sequence based on optimized fluence map is generated; (5) Assuming the patient breathes with a reproducible breathing pattern and the machine maintains a constant dose rate, the treatment process is correlated with the breathing phase; (6) The instantaneous average tumor displacement is overlaid on the dMLC position at corresponding phase; and (7) DMLC leaf speed and acceleration are evaluated to ensure treatment delivery. A custom-built mobile phantom driven by a computer-controlled stepper motor was used in the dosimetry verification. A stepper motor was programmed such that the phantom moved according to the linear component of tumor motion used in BSD treatment planning. A conventional plan was delivered on the phantom with and without motion. The BSD plan was also delivered on the phantom that moved with the prescheduled pattern and synchronized with the delivery of each beam. Film dosimetry showed underdose and overdose in the superior and inferior regions of the target, respectively, if the tumor motion is not compensated during the delivery. BSD delivery resulted in a dose distribution very similar to the planned treatments.« less

WE-DE-201-04: Cross Validation of Knowledge-Based Treatment Planning for Prostate LDR Brachytherapy Using Principle Component Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roper, J; Ghavidel, B; Godette, K

Purpose: To validate a knowledge-based algorithm for prostate LDR brachytherapy treatment planning. Methods: A dataset of 100 cases was compiled from an active prostate seed implant service. Cases were randomized into 10 subsets. For each subset, the 90 remaining library cases were registered to a common reference frame and then characterized on a point by point basis using principle component analysis (PCA). Each test case was converted to PCA vectors using the same process and compared with each library case using a Mahalanobis distance to evaluate similarity. Rank order PCA scores were used to select the best-matched library case. Themore » seed arrangement was extracted from the best-matched case and used as a starting point for planning the test case. Any subsequent modifications were recorded that required input from a treatment planner to achieve V100>95%, V150<60%, V200<20%. To simulate operating-room planning constraints, seed activity was held constant, and the seed count could not increase. Results: The computational time required to register test-case contours and evaluate PCA similarity across the library was 10s. Preliminary analysis of 2 subsets shows that 9 of 20 test cases did not require any seed modifications to obtain an acceptable plan. Five test cases required fewer than 10 seed modifications or a grid shift. Another 5 test cases required approximately 20 seed modifications. An acceptable plan was not achieved for 1 outlier, which was substantially larger than its best match. Modifications took between 5s and 6min. Conclusion: A knowledge-based treatment planning algorithm for prostate LDR brachytherapy is being cross validated using 100 prior cases. Preliminary results suggest that for this size library, acceptable plans can be achieved without planner input in about half of the cases while varying amounts of planner input are needed in remaining cases. Computational time and planning time are compatible with clinical practice.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roper, J; Bradshaw, B; Godette, K

Purpose: To create a knowledge-based algorithm for prostate LDR brachytherapy treatment planning that standardizes plan quality using seed arrangements tailored to individual physician preferences while being fast enough for real-time planning. Methods: A dataset of 130 prior cases was compiled for a physician with an active prostate seed implant practice. Ten cases were randomly selected to test the algorithm. Contours from the 120 library cases were registered to a common reference frame. Contour variations were characterized on a point by point basis using principle component analysis (PCA). A test case was converted to PCA vectors using the same process andmore » then compared with each library case using a Mahalanobis distance to evaluate similarity. Rank order PCA scores were used to select the best-matched library case. The seed arrangement was extracted from the best-matched case and used as a starting point for planning the test case. Computational time was recorded. Any subsequent modifications were recorded that required input from a treatment planner to achieve an acceptable plan. Results: The computational time required to register contours from a test case and evaluate PCA similarity across the library was approximately 10s. Five of the ten test cases did not require any seed additions, deletions, or moves to obtain an acceptable plan. The remaining five test cases required on average 4.2 seed modifications. The time to complete manual plan modifications was less than 30s in all cases. Conclusion: A knowledge-based treatment planning algorithm was developed for prostate LDR brachytherapy based on principle component analysis. Initial results suggest that this approach can be used to quickly create treatment plans that require few if any modifications by the treatment planner. In general, test case plans have seed arrangements which are very similar to prior cases, and thus are inherently tailored to physician preferences.« less

The indexed time table approach for planning and acting

NASA Technical Reports Server (NTRS)

Ghallab, Malik; Alaoui, Amine Mounir

1989-01-01

A representation is discussed of symbolic temporal relations, called IxTeT, that is both powerful enough at the reasoning level for tasks such as plan generation, refinement and modification, and efficient enough for dealing with real time constraints in action monitoring and reactive planning. Such representation for dealing with time is needed in a teleoperated space robot. After a brief survey of known approaches, the proposed representation shows its computational efficiency for managing a large data base of temporal relations. Reactive planning with IxTeT is described and exemplified through the problem of mission planning and modification for a simple surveying satellite.

Planning Coverage Campaigns for Mission Design and Analysis: CLASP for DESDynl

NASA Technical Reports Server (NTRS)

Knight, Russell L.; McLaren, David A.; Hu, Steven

2013-01-01

Mission design and analysis presents challenges in that almost all variables are in constant flux, yet the goal is to achieve an acceptable level of performance against a concept of operations, which might also be in flux. To increase responsiveness, automated planning tools are used that allow for the continual modification of spacecraft, ground system, staffing, and concept of operations, while returning metrics that are important to mission evaluation, such as area covered, peak memory usage, and peak data throughput. This approach was applied to the DESDynl mission design using the CLASP planning system, but since this adaptation, many techniques have changed under the hood for CLASP, and the DESDynl mission concept has undergone drastic changes. The software produces mission evaluation products, such as memory highwater marks, coverage percentages, given a mission design in the form of coverage targets, concept of operations, spacecraft parameters, and orbital parameters. It tries to overcome the lack of fidelity and timeliness of mission requirements coverage analysis during mission design. Previous techniques primarily use Excel in ad hoc fashion to approximate key factors in mission performance, often falling victim to overgeneralizations necessary in such an adaptation. The new program allows designers to faithfully represent their mission designs quickly, and get more accurate results just as quickly.

Planning for robust reserve networks using uncertainty analysis

USGS Publications Warehouse

Moilanen, A.; Runge, M.C.; Elith, Jane; Tyre, A.; Carmel, Y.; Fegraus, E.; Wintle, B.A.; Burgman, M.; Ben-Haim, Y.

2006-01-01

Planning land-use for biodiversity conservation frequently involves computer-assisted reserve selection algorithms. Typically such algorithms operate on matrices of species presence?absence in sites, or on species-specific distributions of model predicted probabilities of occurrence in grid cells. There are practically always errors in input data?erroneous species presence?absence data, structural and parametric uncertainty in predictive habitat models, and lack of correspondence between temporal presence and long-run persistence. Despite these uncertainties, typical reserve selection methods proceed as if there is no uncertainty in the data or models. Having two conservation options of apparently equal biological value, one would prefer the option whose value is relatively insensitive to errors in planning inputs. In this work we show how uncertainty analysis for reserve planning can be implemented within a framework of information-gap decision theory, generating reserve designs that are robust to uncertainty. Consideration of uncertainty involves modifications to the typical objective functions used in reserve selection. Search for robust-optimal reserve structures can still be implemented via typical reserve selection optimization techniques, including stepwise heuristics, integer-programming and stochastic global search.

Mechanical methods of chaparral modification

Treesearch

George Roby; Lisle Green

1976-01-01

Chaparral modification is undertaken for a variety of land-management purposes. To help land managers in selecting equipment and methods for such work, practitioners in county, State, and Federal modification projects were asked for evaluations of equipment and techniques they had used. This handbook describes the alternative techniques and equipment, provides...

75 FR 29784 - Petitions for Modification

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-27

... training plans will apply. The petitioner asserts that the proposed alternative method will at all times... DEPARTMENT OF LABOR Mine Safety and Health Administration Petitions for Modification AGENCY: Mine Safety and Health Administration (MSHA), Labor. ACTION: Notice of petitions for modification of existing...

Advances in the surface modification techniques of bone-related implants for last 10 years

PubMed Central

Qiu, Zhi-Ye; Chen, Cen; Wang, Xiu-Mei; Lee, In-Seop

2014-01-01

At the time of implanting bone-related implants into human body, a variety of biological responses to the material surface occur with respect to surface chemistry and physical state. The commonly used biomaterials (e.g. titanium and its alloy, Co–Cr alloy, stainless steel, polyetheretherketone, ultra-high molecular weight polyethylene and various calcium phosphates) have many drawbacks such as lack of biocompatibility and improper mechanical properties. As surface modification is very promising technology to overcome such problems, a variety of surface modification techniques have been being investigated. This review paper covers recent advances in surface modification techniques of bone-related materials including physicochemical coating, radiation grafting, plasma surface engineering, ion beam processing and surface patterning techniques. The contents are organized with different types of techniques to applicable materials, and typical examples are also described. PMID:26816626

A novel technique for prevention of self-mutilation in three Harris' hawks (Parabuteo unicinctus).

PubMed

Smith, Stephen P; Forbes, Neil A

2009-03-01

Feather destructive behavior is an ever-increasing problem in captive birds of prey and any associated self-mutilation can be challenging to manage. This clinical report describes a noninvasive, nonpainful, temporary beak modification technique used to prevent self-mutilation in 3 Harris' hawks (Parabuteo unicinctus), when other methods and husbandry modifications had failed. The technique was successful in all 3 birds, and no adverse effects were observed. Further investigations are required to further evaluate if this beak modification technique causes any psychologic or physical stress to the avian patient.

Evaluation of Techniques for Reducing In-Use Automotive Fuel Consumption

DOT National Transportation Integrated Search

1981-04-01

This report presents an assessment of proposed techniques for reducing fuel consumption in the in-use light duty road vehicle fleet. Three general classes of techniques are treated: (1) modification of vehicles, (2) modification of traffic flow, and ...

Fifteen-foot diameter modular space station Kennedy Space Center launch site support definition (space station program Phase B extension definition)

NASA Technical Reports Server (NTRS)

Bjorn, L. C.; Martin, M. L.; Murphy, C. W.; Niebla, J. F., V

1971-01-01

This document defines the facilities, equipment, and operational plans required to support the MSS Program at KSC. Included is an analysis of KSC operations, a definition of flow plans, facility utilization and modifications, test plans and concepts, activation, and tradeoff studies. Existing GSE and facilities that have a potential utilization are identified, and new items are defined where possible. The study concludes that the existing facilities are suitable for use in the space station program without major modification from the Saturn-Apollo configuration.

40 CFR 52.2223 - Compliance schedules.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., 1974: Submit to the Administrator a projection of the amount of fuel, by types, that will be... projected above. (iii) April 30, 1974: Submit a statement as to whether boiler modifications will be required. If modifications will be required, submit plans for such modifications. (iv) May 31, 1974: Let...

24 CFR 968.320 - HUD review and approval of comprehensive plan (including five-year action plan).

Code of Federal Regulations, 2012 CFR

2012-04-01

... modifications required to make the comprehensive plan approvable. The PHA must re-submit the comprehensive plan... writing containing any false, fictitious or fraudulent statement or entry, in any matter within the...

24 CFR 968.320 - HUD review and approval of comprehensive plan (including five-year action plan).

Code of Federal Regulations, 2011 CFR

2011-04-01

... modifications required to make the comprehensive plan approvable. The PHA must re-submit the comprehensive plan... writing containing any false, fictitious or fraudulent statement or entry, in any matter within the...

Computed Tomographic Angiographic Perforator Localization for Virtual Surgical Planning of Osteocutaneous Fibular Free Flaps in Head and Neck Reconstruction.

PubMed

Ettinger, Kyle S; Alexander, Amy E; Arce, Kevin

2018-04-10

Virtual surgical planning (VSP), computer-aided design and computer-aided modeling, and 3-dimensional printing are 3 distinct technologies that have become increasingly used in head and neck oncology and microvascular reconstruction. Although each of these technologies has long been used for treatment planning in other surgical disciplines, such as craniofacial surgery, trauma surgery, temporomandibular joint surgery, and orthognathic surgery, its widespread use in head and neck reconstructive surgery remains a much more recent event. In response to the growing trend of VSP being used for the planning of fibular free flaps in head and neck reconstruction, some surgeons have questioned the technology's implementation based on its inadequacy in addressing other reconstructive considerations beyond hard tissue anatomy. Detractors of VSP for head and neck reconstruction highlight its lack of capability in accounting for multiple reconstructive factors, such as recipient vessel selection, vascular pedicle reach, need for dead space obliteration, and skin paddle perforator location. It is with this premise in mind that the authors report on a straightforward technique for anatomically localizing peroneal artery perforators during VSP for osteocutaneous fibular free flaps in which bone and a soft tissue skin paddle are required for ablative reconstruction. The technique allows for anatomic perforator localization during the VSP session based solely on data existent at preoperative computed tomographic angiography (CTA); it does not require any modifications to preoperative clinical workflows. It is the authors' presumption that many surgeons in the field are unaware of this planning capability within the context of modern VSP for head and neck reconstruction. The primary purpose of this report is to introduce and further familiarize surgeons with the technique of CTA perforator localization as a method of improving intraoperative fidelity for VSP of osteocutaneous fibular free flaps. Copyright © 2018. Published by Elsevier Inc.

Getting the Most from the Twin Mars Rovers

NASA Technical Reports Server (NTRS)

Laufenberg, Larry

2003-01-01

The report discusses the Mixed-initiative Activity Planning GENerator (MARGEN) automatically generates activity plans for rovers. Decision support system mixes autonomous planning/scheduling with user modifications. Accommodating change. Technology spotlight

A Technique to Reduce Incidence of Opaque Bubble Layer Formation During LASIK Flap Creation Using the VisuMax Femtosecond Laser.

PubMed

Wu, Ningling; Christenbury, Joseph G; Dishler, Jon G; Bozkurt, Tahir Kansu; Duel, Daniel; Zhang, Lijun; Hamilton, D Rex

2017-09-01

To identify risk factors for opaque bubble layer (OBL) formation and compare the incidence of OBL using a cone modification technique versus the original technique for LASIK flap creation using the VisuMax laser (Carl Zeiss Meditec, Jena, Germany). This retrospective study examined videos of flap creation using the VisuMax laser to identify OBL occurrence. Eyes were divided into three groups: eyes where OBL occurred using the original technique (OBL group), eyes where OBL did not occur using the original technique (no OBL group), and eyes in which the cone modification technique was used for LASIK flap creation (larger flap diameter) (cone modification technique group). Preoperative measurements including simulated keratometry (flat and steep) values, white-to-white distance (WTW), pachymetry, patient age and gender, amount of correction, flap parameters, energy setting, corneal hysteresis, and corneal resistance factor were analyzed to identify parameters with statistical difference between the OBL and no OBL groups. Incidence of OBL was compared between the original and cone modification techniques. OBL incidence was significantly lower with the cone modification technique (7.6%; 7 of 92 eyes) than with the original technique (28.8%; 34 of 118 eyes) (Fisher's exact test, P = .0009). Factors identified with a significant difference between eyes with and without OBL using the original technique were: corneal thickness (OBL: 561.2 μm, no OBL: 549.6 μm, P = .0132), WTW diameter (OBL: 11.6 mm, no OBL: 11.9 mm, P = .0048), corneal resistance factor (OBL: 10.4 mm Hg, no OBL: 9.6 mm Hg, P = 0.0329), and corneal astigmatism (OBL: 0.80 diopter, no OBL: 1.00 diopter, P = .0472) CONCLUSIONS: Less astigmatic, thicker, denser, and smaller corneas increased the risk of OBL using the original technique for flap creation. The cone modification technique was associated with lower risk of OBL formation, even in eyes with significant risk factors for OBL using the original technique. [J Refract Surg. 2017;33(9):584-590.]. Copyright 2017, SLACK Incorporated.

20 CFR 632.17 - Planning process.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Planning process. 632.17 Section 632.17... EMPLOYMENT AND TRAINING PROGRAMS Program Planning, Application and Modification Procedures § 632.17 Planning process. (a) Each Native American grantee shall establish a planning process for the development of its...

Modification of Agility Running Technique in Reaction to a Defender in Rugby Union

PubMed Central

Wheeler, Keane W.; Sayers, Mark G.L.

2010-01-01

Three-dimensional kinematic analysis examined agility running technique during pre-planned and reactive performance conditions specific to attacking ball carries in rugby union. The variation to running technique of 8 highly trained rugby union players was compared between agility conditions (pre-planned and reactive) and also agility performance speeds (fast, moderate and slow). Kinematic measures were used to determine the velocity of the centre of mass (COM) in the anteroposterior (running speed) and mediolateral (lateral movement speed) planes. The position of foot-strike and toe-off was also examined for the step prior to the agility side- step (pre-change of direction phase) and then the side-step (change of direction phase). This study demonstrated that less lateral movement speed towards the intended direction change occurred during reactive compared to pre-planned conditions at pre-change of direction (0.08 ± 0.28 m·s-1 and 0.42 ± 0.25 m·s-1, respectively) and change of direction foot-strikes (0.25 ± 0.42 m·s-1 and 0.69 ± 0.43 m·s-1, respectively). Less lateral movement speed during reactive conditions was associated with greater lateral foot displacement (44.52 ± 6.10% leg length) at the change of direction step compared to pre-planned conditions (41.35 ± 5.85%). Importantly, the anticipation abilities during reactive conditions provided a means to differentiate between speeds of agility performance, with faster performances displaying greater lateral movement speed at the change of direction foot- strike (0.52 ± 0.34 m·s-1) compared to moderate (0.20 ± 0.37 m·s-1) and slow (-0.08 ± 0.31 m·s-1). The changes to running technique during reactive conditions highlight the need to incorporate decision-making in rugby union agility programs. Key points Changes to running technique occur when required to make a decision. Fast agility performers use different stepping strategies in reactive conditions. Decision-making must be incorporated in agility training programs. PMID:24149639

Environmental impact assessment of structural flood mitigation measures by a rapid impact assessment matrix (RIAM) technique: a case study in Metro Manila, Philippines.

PubMed

Gilbuena, Romeo; Kawamura, Akira; Medina, Reynaldo; Amaguchi, Hideo; Nakagawa, Naoko; Bui, Duong Du

2013-07-01

In recent decades, the practice of environmental impact assessment (EIA) in the planning processes of infrastructure projects has created significant awareness on the benefits of environmentally sound and sustainable urban development around the world. In the highly urbanized megacities in the Philippines, like Metro Manila, high priority is given by the national government to structural flood mitigation measures (SFMM) due to the persistently high frequency of flood-related disasters, which are exacerbated by the on-going effects of climate change. EIA thus, should be carefully and effectively executed to maximize the potential benefits of the SFMM. The common practice of EIA in the Philippines is generally qualitative and lacks clear methodology in evaluating multi-criteria systems. Thus, this study proposes the use of the rapid impact assessment matrix (RIAM) technique to provide a method that would systematically and quantitatively evaluate the socio-economic and environmental impacts of planned SFMM in Metro Manila. The RIAM technique was slightly modified to fit the requirements of this study. The scale of impact was determined for each perceived impact, and based on the results, the planned SFMM for Metro Manila will likely bring significant benefits; however, significant negative impacts may also likely occur. The proposed modifications were found to be highly compatible with RIAM, and the results of the RIAM analysis provided a clear view of the impacts associated with the implementation of SFMM projects. This may prove to be valuable in the practice of EIA in the Philippines. Copyright © 2013 Elsevier B.V. All rights reserved.

Enhanced visualization of MR angiogram with modified MIP and 3D image fusion

NASA Astrophysics Data System (ADS)

Kim, JongHyo; Yeon, Kyoung M.; Han, Man Chung; Lee, Dong Hyuk; Cho, Han I.

1997-05-01

We have developed a 3D image processing and display technique that include image resampling, modification of MIP, volume rendering, and fusion of MIP image with volumetric rendered image. This technique facilitates the visualization of the 3D spatial relationship between vasculature and surrounding organs by overlapping the MIP image on the volumetric rendered image of the organ. We applied this technique to a MR brain image data to produce an MRI angiogram that is overlapped with 3D volume rendered image of brain. MIP technique was used to visualize the vasculature of brain, and volume rendering was used to visualize the other structures of brain. The two images are fused after adjustment of contrast and brightness levels of each image in such a way that both the vasculature and brain structure are well visualized either by selecting the maximum value of each image or by assigning different color table to each image. The resultant image with this technique visualizes both the brain structure and vasculature simultaneously, allowing the physicians to inspect their relationship more easily. The presented technique will be useful for surgical planning for neurosurgery.

20 CFR 632.22 - Modification of a Comprehensive Annual Plan (CAP) and/or Master Plan.

Code of Federal Regulations, 2012 CFR

2012-04-01

... (CAP) and/or Master Plan. 632.22 Section 632.22 Employees' Benefits EMPLOYMENT AND TRAINING... Master Plan. (a) The requirements for modifying a Master Plan and/or CAP will be included in administrative instructions issued by the Grant Officer upon final implementation of the Master Plan/CAP system...

20 CFR 632.22 - Modification of a Comprehensive Annual Plan (CAP) and/or Master Plan.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (CAP) and/or Master Plan. 632.22 Section 632.22 Employees' Benefits EMPLOYMENT AND TRAINING... Master Plan. (a) The requirements for modifying a Master Plan and/or CAP will be included in administrative instructions issued by the Grant Officer upon final implementation of the Master Plan/CAP system...

Comparison of time required for traditional versus virtual orthognathic surgery treatment planning.

PubMed

Wrzosek, M K; Peacock, Z S; Laviv, A; Goldwaser, B R; Ortiz, R; Resnick, C M; Troulis, M J; Kaban, L B

2016-09-01

Virtual surgical planning (VSP) is a tool for predicting complex surgical movements in three dimensions and it may reduce preoperative laboratory time. A prospective study to compare the time required for standard preoperative planning versus VSP was conducted at Massachusetts General Hospital from January 2014 through January 2015. Workflow data for bimaxillary cases planned by both standard techniques and VSP were recorded in real time. Time spent was divided into three parts: (1) obtaining impressions, face-bow mounting, and model preparation; (2) occlusal analysis and modification, model surgery, and splint fabrication; (3) online VSP session. Average times were compared between standard treatment planning (sum of parts 1 and 2) and VSP (sum of parts 1 and 3). Of 41 bimaxillary cases included, 20 were simple (symmetric) and 21 were complex (asymmetry and segmental osteotomies). Average times for parts 1, 2, and 3 were 4.43, 3.01, and 0.67h, respectively. The average time required for standard treatment planning was 7.45h and for VSP was 5.10h, a 31% time reduction (P<0.001). By eliminating all or some components of part 1, time savings may increase to as much as 91%. This study indicates that in an academic setting, VSP reduces the time required for treatment planning of bimaxillary orthognathic surgery cases. Copyright © 2016 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

20 CFR 628.420 - Job training plan.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 20 Employees' Benefits 3 2011-04-01 2011-04-01 false Job training plan. 628.420 Section 628.420... THE JOB TRAINING PARTNERSHIP ACT Local Service Delivery System § 628.420 Job training plan. (a) The Governor shall issue instructions and schedules to assure that job training plans and plan modifications...

20 CFR 628.420 - Job training plan.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 20 Employees' Benefits 3 2012-04-01 2012-04-01 false Job training plan. 628.420 Section 628.420... THE JOB TRAINING PARTNERSHIP ACT Local Service Delivery System § 628.420 Job training plan. (a) The Governor shall issue instructions and schedules to assure that job training plans and plan modifications...

Understanding Preservice Teacher Skills to Construct Lesson Plans

ERIC Educational Resources Information Center

Lim, Woong; Son, Ji-Won; Kim, Dong-Joong

2018-01-01

This study examined preservice teachers' (PSTs) capacity for lesson planning in a university-based teacher preparation program in the USA Participants (n = 126) wrote lesson plans in three approaches: synthesis, creation, and modification. Findings indicate that PSTs who modified preexisting lesson plans produced better lesson plans than their…

20 CFR 628.420 - Job training plan.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Job training plan. 628.420 Section 628.420... THE JOB TRAINING PARTNERSHIP ACT Local Service Delivery System § 628.420 Job training plan. (a) The Governor shall issue instructions and schedules to assure that job training plans and plan modifications...

Planning for Obsolescence.

ERIC Educational Resources Information Center

Malinconico, S. Michael

1984-01-01

Discusses planning for the implementation of a high technology system which includes plans for how it will be phased out and an orderly transition made to its successor. System life expectations, user pressures, software modifications, commercial vendors, integrated systems, eroding economies, and replacement planning are highlighted. (EJS)

48 CFR 307.7101 - Policy.

Code of Federal Regulations, 2011 CFR

2011-10-01

... PLANNING ACQUISITION PLANNING Acquisition Plan 307.7101 Policy. (a) An AP is required for all acquisitions... GWAC; or (ii) A BPA, provided there is an approved acquisition planning document for the original... under HHS-wide strategic sourcing vehicles. (8) Contract/order modifications that— (i) Exercise options...

2-[18F]fluoro-2-deoxyglucose positron-emission tomography in staging, response evaluation, and treatment planning of lymphomas.

PubMed

Specht, Lena

2007-07-01

2-[18F]fluoro-2-deoxyglucose positron-emission tomography (FDG-PET) is used increasingly in the clinical management of lymphomas. With regard to staging, FDG-PET is more sensitive and specific than conventional staging methods in FDG avid lymphomas (ie, Hodgkin lymphoma and most aggressive non-Hodgkin lymphomas). Despite methodological problems, in particular the lack of a valid reference test, FDG-PET is approved and generally used for this purpose. With regard to response evaluation, FDG-PET at the end of treatment seems to aid considerably in differentiating between residual masses with or without residual lymphoma. Hence, new revised response criteria have been proposed, incorporating the result of FDG-PET at the end of treatment. An early interim FDG-PET scan after 1 to 3 cycles of chemotherapy is a very strong predictor of outcome, and trials are now in progress testing treatment modifications on this basis. With regard to treatment planning, in the context of combined-modality therapy, radiotherapy for lymphomas is moving toward more conformal techniques reducing the irradiated volume to include only the macroscopic lymphoma. In this situation, accurate imaging is essential, and FDG-PET coregistered with the planning computed tomography (CT) scan is used increasingly. The availability of PET/CT scanners suited for virtual simulation has aided this process. However, clinical data evaluating this technique are at present sparse.

40 CFR 72.81 - Permit modifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... compliance deadline extension; and (5) Changes in a thermal energy plan that result in any addition or... replacement of thermal energy. (c)(1) Permit modifications shall follow the permit issuance requirements of...

40 CFR 72.81 - Permit modifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... compliance deadline extension; and (5) Changes in a thermal energy plan that result in any addition or... replacement of thermal energy. (c)(1) Permit modifications shall follow the permit issuance requirements of...

40 CFR 72.81 - Permit modifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... compliance deadline extension; and (5) Changes in a thermal energy plan that result in any addition or... replacement of thermal energy. (c)(1) Permit modifications shall follow the permit issuance requirements of...

40 CFR 72.81 - Permit modifications.

Code of Federal Regulations, 2011 CFR

2011-07-01

... compliance deadline extension; and (5) Changes in a thermal energy plan that result in any addition or... replacement of thermal energy. (c)(1) Permit modifications shall follow the permit issuance requirements of...

40 CFR 72.81 - Permit modifications.

Code of Federal Regulations, 2014 CFR

2014-07-01

... compliance deadline extension; and (5) Changes in a thermal energy plan that result in any addition or... replacement of thermal energy. (c)(1) Permit modifications shall follow the permit issuance requirements of...

Control of Technology Transfer at JPL

NASA Technical Reports Server (NTRS)

Oliver, Ronald

2006-01-01

Controlled Technology: 1) Design: preliminary or critical design data, schematics, technical flow charts, SNV code/diagnostics, logic flow diagrams, wirelist, ICDs, detailed specifications or requirements. 2) Development: constraints, computations, configurations, technical analyses, acceptance criteria, anomaly resolution, detailed test plans, detailed technical proposals. 3) Production: process or how-to: assemble, operated, repair, maintain, modify. 4) Manufacturing: technical instructions, specific parts, specific materials, specific qualities, specific processes, specific flow. 5) Operations: how-to operate, contingency or standard operating plans, Ops handbooks. 6) Repair: repair instructions, troubleshooting schemes, detailed schematics. 7) Test: specific procedures, data, analysis, detailed test plan and retest plans, detailed anomaly resolutions, detailed failure causes and corrective actions, troubleshooting, trended test data, flight readiness data. 8) Maintenance: maintenance schedules and plans, methods for regular upkeep, overhaul instructions. 9) Modification: modification instructions, upgrades kit parts, including software

Hot-wire anemometry in hypersonic helium flow

NASA Technical Reports Server (NTRS)

Wagner, R. D.; Weinstein, L. M.

1974-01-01

Hot-wire anemometry techniques are described that have been developed and used for hypersonic-helium-flow studies. The short run time available dictated certain innovations in applying conventional hot-wire techniques. Some examples are given to show the application of the techniques used. Modifications to conventional equipment are described, including probe modifications and probe heating controls.

40 CFR 52.233 - Review of new sources and modifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 3 2013-07-01 2013-07-01 false Review of new sources and modifications. 52.233 Section 52.233 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS California § 52.233 Review of new sources and modifications. (a) The following...

40 CFR 52.233 - Review of new sources and modifications.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 3 2014-07-01 2014-07-01 false Review of new sources and modifications. 52.233 Section 52.233 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS California § 52.233 Review of new sources and modifications. (a) The following...

40 CFR 52.233 - Review of new sources and modifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 3 2012-07-01 2012-07-01 false Review of new sources and modifications. 52.233 Section 52.233 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS California § 52.233 Review of new sources and modifications. (a) The following...

40 CFR 52.2592 - Review of new sources and modifications.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Wisconsin § 52.2592 Review of new sources and modifications. Disapproval—On May 12, 2011, the Wisconsin Department of Natural...

A case study of IMRT planning (Plan B) subsequent to a previously treated IMRT plan (Plan A)

NASA Astrophysics Data System (ADS)

Cao, F.; Leong, C.; Schroeder, J.; Lee, B.

2014-03-01

Background and purpose: Treatment of the contralateral neck after previous ipsilateral intensity modulated radiation therapy (IMRT) for head and neck cancer is a challenging problem. We have developed a technique that limits the cumulative dose to the spinal cord and brainstem while maximizing coverage of a planning target volume (PTV) in the contralateral neck. Our case involves a patient with right tonsil carcinoma who was given ipsilateral IMRT with 70Gy in 35 fractions (Plan A). A left neck recurrence was detected 14 months later. The patient underwent a neck dissection followed by postoperative left neck radiation to a dose of 66 Gy in 33 fractions (Plan B). Materials and Methods: The spinal cord-brainstem margin (SCBM) was defined as the spinal cord and brainstem with a 1.0 cm margin. Plan A was recalculated on the postoperative CT scan but the fluence outside of SCBM was deleted. A further modification of Plan A resulted in a base plan that was summed with Plan B to evaluate the cumulative dose received by the spinal cord and brainstem. Plan B alone was used to evaluate for coverage of the contralateral neck PTV. Results: The maximum cumulative doses to the spinal cord with 0.5cm margin and brainstem with 0.5cm margin were 51.96 Gy and 45.60 Gy respectively. For Plan B, 100% of the prescribed dose covered 95% of PTVb1. Conclusion: The use of a modified ipsilateral IMRT plan as a base plan is an effective way to limit the cumulative dose to the spinal cord and brainstem while enabling coverage of a PTV in the contralateral neck.

40 CFR 60.2055 - What is a waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false What is a waste management plan? 60... Which Modification or Reconstruction Is Commenced on or After June 1, 2001 Waste Management Plan § 60.2055 What is a waste management plan? A waste management plan is a written plan that identifies both...

40 CFR 60.2899 - What is a waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false What is a waste management plan? 60... Modification or Reconstruction is Commenced on or After June 16, 2006 Waste Management Plan § 60.2899 What is a waste management plan? A waste management plan is a written plan that identifies both the feasibility...

40 CFR 60.2055 - What is a waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false What is a waste management plan? 60... Which Modification or Reconstruction Is Commenced on or After June 1, 2001 Waste Management Plan § 60.2055 What is a waste management plan? A waste management plan is a written plan that identifies both...

40 CFR 60.2899 - What is a waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false What is a waste management plan? 60... Modification or Reconstruction is Commenced on or After June 16, 2006 Waste Management Plan § 60.2899 What is a waste management plan? A waste management plan is a written plan that identifies both the feasibility...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harris, Victoria A.; Staffurth, John; Naismith, Olivia

Purpose: The purpose of this study was to establish reproducible guidelines for delineating the clinical target volume (CTV) of the pelvic lymph nodes (LN) by combining the freehand Royal Marsden Hospital (RMH) and Radiation Therapy Oncology Group (RTOG) vascular expansion techniques. Methods and Materials: Seven patients with prostate cancer underwent standard planning computed tomography scanning. Four different CTVs (RMH, RTOG, modified RTOG, and Prostate and pelvIs Versus prOsTate Alone treatment for Locally advanced prostate cancer [PIVOTAL] trial) were created for each patient, and 6 different bowel expansion margins (BEM) were created to assess bowel avoidance by the CTV. The resulting CTVsmore » were compared visually and by using Jaccard conformity indices. The volume of overlap between bowel and planning target volume (PTV) was measured to aid selection of an appropriate BEM to enable maximal LN yet minimal normal tissue coverage. Results: In total, 84 nodal contours were evaluated. LN coverage was similar in all groups, with all of the vascular-expansion techniques (RTOG, modified RTOG, and PIVOTAL), resulting in larger CTVs than that of the RMH technique (mean volumes: 287.3 cm{sup 3}, 326.7 cm{sup 3}, 310.3 cm{sup 3}, and 256.7 cm{sup 3}, respectively). Mean volumes of bowel within the modified RTOG PTV were 19.5 cm{sup 3} (with 0 mm BEM), 17.4 cm{sup 3} (1-mm BEM), 10.8 cm{sup 3} (2-mm BEM), 6.9 cm{sup 3} (3-mm BEM), 5.0 cm{sup 3} (4-mm BEM), and 1.4 cm{sup 3} (5-mm BEM) in comparison with an overlap of 9.2 cm{sup 3} seen using the RMH technique. Evaluation of conformity between LN-CTVs from each technique revealed similar volumes and coverage. Conclusions: Vascular expansion techniques result in larger LN-CTVs than the freehand RMH technique. Because the RMH technique is supported by phase 1 and 2 trial safety data, we proposed modifications to the RTOG technique, including the addition of a 3-mm BEM, which resulted in LN-CTV coverage similar to that of the RMH technique, with reduction in bowel and planning target volume overlap. On the basis of these findings, recommended guidelines including a detailed pelvic LN contouring atlas have been produced and implemented in the PIVOTAL trial.« less

Classroom Management Through the Application of Behavior Modification Techniques.

ERIC Educational Resources Information Center

Ferinden, William E., Jr.

The primary aim of this book is to bring to the grade school teacher a survey of the most recent techniques and ideas of behavior modification which are applicable to good classroom management. All of the approaches and techniques presented could be of interest to teachers working at all grade levels. Since research has shown that the systematic…

30 CFR 582.21 - Plans, general.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... proposed Delineation, Testing, and Mining Plans and any proposal for a significant modification to an... required to submit a Delineation or Testing Plan prior to submittal of a proposed Testing or Mining Plan if...

30 CFR 582.21 - Plans, general.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... proposed Delineation, Testing, and Mining Plans and any proposal for a significant modification to an... required to submit a Delineation or Testing Plan prior to submittal of a proposed Testing or Mining Plan if...

30 CFR 582.21 - Plans, general.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... proposed Delineation, Testing, and Mining Plans and any proposal for a significant modification to an... required to submit a Delineation or Testing Plan prior to submittal of a proposed Testing or Mining Plan if...

Behavior Modification in the Classroom

ERIC Educational Resources Information Center

Whitman, Mryon; Whitman, Joan

1971-01-01

This article presents the theoretical rationale for behavior modification, principally through its comparison with traditional psychotherapies, and suggests some behavior modification techniques for the classroom management of maladaptive behavior. (Author)

TU-AB-303-01: A Feasibility Study for Dynamic Adaptive Therapy of Non-Small Cell Lung Cancer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, M; Phillips, M

2015-06-15

Purpose: To compare plans for NSCLC optimized using Dynamic Adaptive Therapy (DAT) with conventional IMRT optimization. DAT adapts plans based on changes in the target volume by using dynamic programing techniques to consider expected changes into the optimization process. Information gathered during treatment, e.g. from CBCT, is incorporated into the optimization. Methods and materials: DAT is formulated using stochastic control formalism, which minimizes the total expected number of tumor cells at the end of a treatment course subject to uncertainty inherent in the tumor response and organs-at-risk (OAR) dose constraints. This formulation allows for non-stationary dose distribution as well asmore » non-stationary fractional dose as needed to achieve a series of optimal plans that are conformal to tumor over time. Sixteen phantom cases with various sizes and locations of tumors, and OAR geometries were generated. Each case was planned with DAT and conventional IMRT (60Gy/30fx). Tumor volume change over time was obtained by using, daily MVCT-based, two-level cell population model. Monte Carlo simulations have been performed for each treatment course to account for uncertainty in tumor response. Same OAR dose constraints were applied for both methods. The frequency of plan modification was varied to 1, 2, 5 (weekly), and 29 (daily). The final average tumor dose and OAR doses have been compared to quantify the potential benefit of DAT. Results: The average tumor max, min, mean, and D95 resulted from DAT were 124.0–125.2%, 102.1–114.7%, 113.7–123.4%, and 102.0–115.9% (range dependent on the frequency of plan modification) of those from conventional IMRT. Cord max, esophagus max, lung mean, heart mean, and unspecified tissue D05 resulted from AT were 84–102.4%, 99.8–106.9%, 66.9–85.6%, 58.2–78.8%, and 85.2–94.0% of those from conventional IMRT. Conclusions: Significant tumor dose increase and OAR dose reduction, especially with parallel OAR with mean or dose-volume constraints, can be achieved using DAT.« less

48 CFR 2.101 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... research, planning, development, design, construction, alteration, or repair of real property; and (3..., evaluations, consultations, comprehensive planning, program management, conceptual designs, plans and... include the value and size of the modification and the comparative value and size of the final product...

48 CFR 2.101 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... research, planning, development, design, construction, alteration, or repair of real property; and (3..., evaluations, consultations, comprehensive planning, program management, conceptual designs, plans and... minor include the value and size of the modification and the comparative value and size of the final...

A Review of Some Alternative Approaches to Drug Management of Hyperactivity in Children.

ERIC Educational Resources Information Center

Walden, Everett L.; Thompson, Sheila A.

1981-01-01

Literature is cited on such classroom management techniques as environmental manipulations, curriculum modifications, behavior modification, and dealing with affective attitude. Also considered are home management techniques and self-control programs including biofeedback and relaxation training. (SB)

40 CFR 60.2900 - When must I submit my waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false When must I submit my waste management... Waste Management Plan § 60.2900 When must I submit my waste management plan? You must submit a waste management plan prior to commencing construction, reconstruction, or modification. ...

40 CFR 264.52 - Content of contingency plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... waste management provisions that are sufficient to comply with the requirements of this part. The owner... that the plan be based on the National Response Team's Integrated Contingency Plan Guidance (“One Plan”). When modifications are made to non-RCRA provisions in an integrated contingency plan, the changes do...

40 CFR 60.2900 - When must I submit my waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false When must I submit my waste management... Waste Management Plan § 60.2900 When must I submit my waste management plan? You must submit a waste management plan prior to commencing construction, reconstruction, or modification. ...

40 CFR 60.2900 - When must I submit my waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false When must I submit my waste management... Waste Management Plan § 60.2900 When must I submit my waste management plan? You must submit a waste management plan prior to commencing construction, reconstruction, or modification. ...

Uterosacral ligament vaginal vault suspension: anatomy, outcome and surgical considerations.

PubMed

Yazdany, Taji; Bhatia, Narender

2008-10-01

With aging populations, primary pelvic organ and recurrent pelvic organ prolapse have become a large-scale public health concern. Surgical options for patients include both abdominal and vaginal approaches, each with its own safety and efficacy profiles. This review summarizes the most recent anatomic, surgical and outcome data for uterosacral ligament vault suspension. It offers data on methods to avoid complications and difficult surgical scenarios. Uterosacral ligament suspension allows reattachment of the vaginal vault high within the pelvis. New modifications in technique including the extraperitoneal and laparoscopic approaches allow surgeons more freedom when planning surgery. Five-year data on the durability of the procedure make it a viable surgical option. As a technique widely used by many pelvic reconstructive surgeons, uterosacral ligament vault suspension provides a safe, anatomically correct and durable approach to uterine and vault prolapse. It requires advanced surgical training and an intimate understanding of pelvic anatomy to avoid and identify ureteral injury.

Planning for coordinated space and ground-based ionospheric modification experiments

NASA Technical Reports Server (NTRS)

Lee, M. C.; Burke, William J.; Carlson, Herbert C.; Heckscher, John L.; Kossey, Paul A.; Weber, E. J.; Kuo, S. P.

1990-01-01

The planning and conduction of coordinated space and ground-based ionospheric modification experiments are discussed. The purpose of these experiments is to discuss: (1) the nonlinear VLF wave interaction with the ionospheric plasmas; and (2) the nonlinear propagation of VLF waves in the HF-modified ionosphere. It is expected that the HF-induced ionospheric density striations can render the nonlinear mode conversion of VLF waved into lower hybrid waves. Lower hybrid waves can also be excited parametrically by the VLF waves in the absence of the density striations if the VLF waves are intense enough. Laboratory experiments are planned for crosschecking the results obtained from the field experiments.

Patchogue River, Westbrook, Connecticut. Small Navigation Project, Detailed Project Report and Environmental Assessment.

DTIC Science & Technology

1982-12-01

Westbrook, especially if channel modifications are undertaken. Currently, local entrepreneurs are planning to construct new power- boat facilities...result. Value of Delay Time Existing S14,400 W/Plan B 7,200 PLAN B: Annual Benefit = S 7,200 PLAN C Plan C would increse the width of the existing channel

Consequences of additional use of PET information for target volume delineation and radiotherapy dose distribution for esophageal cancer.

PubMed

Muijs, Christina T; Schreurs, Liesbeth M; Busz, Dianne M; Beukema, Jannet C; van der Borden, Arnout J; Pruim, Jan; Van der Jagt, Eric J; Plukker, John Th; Langendijk, Johannes A

2009-12-01

To determine the consequences of target volume (TV) modifications, based on the additional use of PET information, on radiation planning, assuming PET/CT-imaging represents the true extent of the tumour. For 21 patients with esophageal cancer, two separate TV's were retrospectively defined based on CT (CT-TV) and co-registered PET/CT images (PET/CT-TV). Two 3D-CRT plans (prescribed dose 50.4 Gy) were constructed to cover the corresponding TV's. Subsequently, these plans were compared for target coverage, normal tissue dose-volume histograms and the corresponding normal tissue complication probability (NTCP) values. The addition of PET led to the modification of CT-TV with at least 10% in 12 of 21 patients (57%) (reduction in 9, enlargement in 3). PET/CT-TV was inadequately covered by the CT-based treatment plan in 8 patients (36%). Treatment plan modifications resulted in significant changes (p<0.05) in dose distributions to heart and lungs. Corresponding changes in NTCP values ranged from -3% to +2% for radiation pneumonitis and from -0.2% to +1.2% for cardiac mortality. This study demonstrated that TV's based on CT might exclude PET-avid disease. Consequences are under dosing and thereby possibly ineffective treatment. Moreover, the addition of PET in radiation planning might result in clinical important changes in NTCP.

Newly Developed Techniques on Polycondensation, Ring-Opening Polymerization and Polymer Modification: Focus on Poly(Lactic Acid)

PubMed Central

Hu, Yunzi; Daoud, Walid A.; Cheuk, Kevin Ka Leung; Lin, Carol Sze Ki

2016-01-01

Polycondensation and ring-opening polymerization are two important polymer synthesis methods. Poly(lactic acid), the most typical biodegradable polymer, has been researched extensively from 1900s. It is of significant importance to have an up-to-date review on the recent improvement in techniques for biodegradable polymers. This review takes poly(lactic acid) as the example to present newly developed polymer synthesis techniques on polycondensation and ring-opening polymerization reported in the recent decade (2005–2015) on the basis of industrial technique modifications and advanced laboratory research. Different polymerization methods, including various solvents, heating programs, reaction apparatus and catalyst systems, are summarized and compared with the current industrial production situation. Newly developed modification techniques for polymer properties improvement are also discussed based on the case of poly(lactic acid). PMID:28773260

Study on modification of the Misgav Ladach method for cesarean section.

PubMed

Li, M; Zou, L; Zhu, J

2001-01-01

172 cases of pregnant women scheduled for delivery by cesarean section were randomly assigned to 59 cases in modification group with modified Misgav Ladach technique, 57 cases in Misgav Ladach group with Misgav Ladach technique and 56 cases in Pfannenstiel group with Pfannenstiel technique from May to Dec. 1999. The modified points included: transversely incising the fascia 2 to 3 cm, then dividing it bluntly; without opening and dissociating the visceral peritoneum; two layers suturing of low transverse uterine incision; closing the skin by continuous suturing. Results showed the average delivery time in the modification group was (3.6 +/- 2.6) min and (5.7 +/- 2.9) min in the Misgav Ladach group (P < 0.05). Median operating time was (28.3 +/- 5.4) min in modification group compared with (27.5 +/- 6.5) min in the Misgav Ladach group (P > 0.05). Average blood loss was (128 +/- 35) ml in modification group compared with (212 +/- 147) ml in the Pfannenstiel group (P < 0.05). It was concluded that the modified Misgav Ladach technique not only preserved all advantages of Misgav Ladach method, but also had additional advantages, such as faster in delivering the fetus, less damage, easier mastering for obstetricians.

Situationally driven local navigation for mobile robots. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Slack, Marc Glenn

1990-01-01

For mobile robots to autonomously accommodate dynamically changing navigation tasks in a goal-directed fashion, they must employ navigation plans. Any such plan must provide for the robot's immediate and continuous need for guidance while remaining highly flexible in order to avoid costly computation each time the robot's perception of the world changes. Due to the world's uncertainties, creation and maintenance of navigation plans cannot involve arbitrarily complex processes, as the robot's perception of the world will be in constant flux, requiring modifications to be made quickly if they are to be of any use. This work introduces navigation templates (NaT's) which are building blocks for the construction and maintenance of rough navigation plans which capture the relationship that objects in the world have to the current navigation task. By encoding only the critical relationship between the objects in the world and the navigation task, a NaT-based navigation plan is highly flexible; allowing new constraints to be quickly incorporated into the plan and existing constraints to be updated or deleted from the plan. To satisfy the robot's need for immediate local guidance, the NaT's forming the current navigation plan are passed to a transformation function. The transformation function analyzes the plan with respect to the robot's current location to quickly determine (a few times a second) the locally preferred direction of travel. This dissertation presents NaT's and the transformation function as well as the needed support systems to demonstrate the usefulness of the technique for controlling the actions of a mobile robot operating in an uncertain world.

An evaluation of health benefit modification in Taft-Hartley health and welfare funds: implications for encouraging tobacco-cessation coverage.

PubMed

Au-Yeung, Caroline M; Weisman, Susan R; Hennrikus, Deborah J; Forster, Jean L; Skoog, Rodney; Luneburg, Wade; Hesse, Bernie

2010-12-01

An estimated one fifth of all U.S. adult smokers receive health benefits through insurance plans administered by Taft-Hartley Health and Welfare Funds. Most funds do not offer comprehensive tobacco-cessation services to fund participants despite evidence that doing so would be cost effective and save lives. This paper examines the decision-making processes of Minnesota-based fund trustees and advisors to identify factors that influence decisions about modifications to benefits. Formative data about the process by which funds make health benefit modifications were collected in 2007-2008 from 25 in-depth key informant interviews with fund trustees and a cross-section of fund advisors, including administrators, attorneys, and healthcare business consultants. Analyses were performed using a general inductive approach to identify conceptual themes, employing qualitative data analysis software. The most commonly cited factors influencing trustees' decisions about health plan benefit modifications-including modifications regarding tobacco-cessation benefits-were benefit costs, participants' demand for services, and safeguarding participants' health. Barriers included information gaps, concerns about participants' response, and difficulty projecting benefit utilization and success. Advisors wielded considerable influence in decision-making processes. Trustees relied on a small pool of business, legal, and administrative advisors to provide guidance and recommendations about possible health plan benefit modifications. Providing advisors with evidence-based information and resources about benefit design, cost/return-on-investment (ROI), effectiveness, and promotion may be an effective means to influence funds to provide comprehensive tobacco-cessation benefits. Copyright © 2010 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Ecological Effects of Weather Modification: A Problem Analysis.

ERIC Educational Resources Information Center

Cooper, Charles F.; Jolly, William C.

This publication reviews the potential hazards to the environment of weather modification techniques as they eventually become capable of producing large scale weather pattern modifications. Such weather modifications could result in ecological changes which would generally require several years to be fully evident, including the alteration of…

Atmospheric release model for the E-area low-level waste facility: Updates and modifications

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

The atmospheric release model (ARM) utilizes GoldSim® Monte Carlo simulation software (GTG, 2017) to evaluate the flux of gaseous radionuclides as they volatilize from E-Area disposal facility waste zones, diffuse into the air-filled soil pores surrounding the waste, and emanate at the land surface. This report documents the updates and modifications to the ARM for the next planned E-Area PA considering recommendations from the 2015 PA strategic planning team outlined by Butcher and Phifer.

Simultaneous F 0-F 1 modifications of Arabic for the improvement of natural-sounding

NASA Astrophysics Data System (ADS)

Ykhlef, F.; Bensebti, M.

2013-03-01

Pitch (F 0) modification is one of the most important problems in the area of speech synthesis. Several techniques have been developed in the literature to achieve this goal. The main restrictions of these techniques are in the modification range and the synthesised speech quality, intelligibility and naturalness. The control of formants in a spoken language can significantly improve the naturalness of the synthesised speech. This improvement is mainly dependent on the control of the first formant (F 1). Inspired by this observation, this article proposes a new approach that modifies both F 0 and F 1 of Arabic voiced sounds in order to improve the naturalness of the pitch shifted speech. The developed strategy takes a parallel processing approach, in which the analysis segments are decomposed into sub-bands in the wavelet domain, modified in the desired sub-band by using a resampling technique and reconstructed without affecting the remained sub-bands. Pitch marking and voicing detection are performed in the frequency decomposition step based on the comparison of the multi-level approximation and detail signals. The performance of the proposed technique is evaluated by listening tests and compared to the pitch synchronous overlap and add (PSOLA) technique in the third approximation level. Experimental results have shown that the manipulation in the wavelet domain of F 0 in conjunction with F 1 guarantees natural-sounding of the synthesised speech compared to the classical pitch modification technique. This improvement was appropriate for high pitch modifications.

24 CFR 201.18 - Modification agreement or repayment plan.

Code of Federal Regulations, 2011 CFR

2011-04-01

... brought current before or by the end of the loan term. A modification agreement may also be used in lieu of refinancing in connection with a loan that is current to effect a reduction in the interest rate...

24 CFR 201.18 - Modification agreement or repayment plan.

Code of Federal Regulations, 2010 CFR

2010-04-01

... brought current before or by the end of the loan term. A modification agreement may also be used in lieu of refinancing in connection with a loan that is current to effect a reduction in the interest rate...

Wind Shear radar program future plans

NASA Technical Reports Server (NTRS)

Robertson, Roy E.

1991-01-01

The status of the Windshear Radar Program at the Collins Air Transport Division of Rockwell International is given in viewgraph form. Topics covered include goals, modifications to the WXR-700 system, flight test plans, technical approaches, design considerations, system considerations, certification, and future plans.

Does Tropical Cyclone Modification Make Sense? A Decision-Analytic Assessment

NASA Astrophysics Data System (ADS)

Klima, K.; Morgan, M. G.; Grossmann, I.

2009-12-01

Since the demise of project Stormfury in 1983, little attention has been devoted to the possibility of intentionally modifying tropical cyclones (TC). However, following Hurricane Katrina and three other Category 5 hurricanes (Emily, Rita, and Wilma), which together resulted in at least 2,280 deaths and over $120-billion in damages (Blake et al., 2007), the U.S. Department of Homeland Security (DHS) has recently begun to support an effort to identify and evaluate hurricane mitigation strategies through Project HURRMIT ([http://www.ofcm.noaa.gov/ihc09/Presentations/Session10/s10-01Woodley.ppt]). Using a decision analytic framing and FEMA's HAZUS-MH MR3 damage model (http://www.fema.gov/plan/prevent/hazus/]), this paper asks, how sure must one be that an intervention will reduce TC damages before choosing to undertake a program of modification? The analysis is formulated in probabilistic terms, and assesses net benefits. In contrast to a much earlier application of decision analysis to TC-modification (Howard et al., 1972) , this work uses census data on the value of property at risk, and prior distributions on changing storm behavior based on data from hurricanes approaching the east coast of Florida since 1953. Even before considering both issues of liability that may arise from the fact that a modified storm is no longer "an act of God" as well as unforeseen environmental consequences, our results suggest that while TC modification techniques will likely alter TC behavior, one will have to be significantly more confident of the predictability and effectiveness of modification methods before their use can be justified. This work is supported by the Climate Decision Making Center through a cooperative agreement between the National Science Foundation (SES-0345798) and Carnegie Mellon University.

20 CFR 632.23 - Termination and corrective action of a CAP and/or Master Plan.

Code of Federal Regulations, 2012 CFR

2012-04-01

... and/or Master Plan. 632.23 Section 632.23 Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION... and Modification Procedures § 632.23 Termination and corrective action of a CAP and/or Master Plan. (a) Emergency Termination. The Department may terminate or suspend a CAP designation or Master Plan under...

20 CFR 632.23 - Termination and corrective action of a CAP and/or Master Plan.

Code of Federal Regulations, 2011 CFR

2011-04-01

... and/or Master Plan. 632.23 Section 632.23 Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION... and Modification Procedures § 632.23 Termination and corrective action of a CAP and/or Master Plan. (a) Emergency Termination. The Department may terminate or suspend a CAP designation or Master Plan under...

29 CFR 4211.12 - Modifications to the presumptive, modified presumptive and rolling-5 methods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... presumptive method (including a plan that primarily covers employees in the building and construction industry... the building and construction industry, the plan year designated by a plan amendment pursuant to... after the designated plan year are reduced by the value of all outstanding claims for withdrawal...

29 CFR 4211.12 - Modifications to the presumptive, modified presumptive and rolling-5 methods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... presumptive method (including a plan that primarily covers employees in the building and construction industry... the building and construction industry, the plan year designated by a plan amendment pursuant to... after the designated plan year are reduced by the value of all outstanding claims for withdrawal...

29 CFR 4211.12 - Modifications to the presumptive, modified presumptive and rolling-5 methods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... presumptive method (including a plan that primarily covers employees in the building and construction industry... the building and construction industry, the plan year designated by a plan amendment pursuant to... after the designated plan year are reduced by the value of all outstanding claims for withdrawal...

76 FR 76182 - Agency Information Collection Activities; Submission for OMB Review; Comment Request; Planning...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-06

... for OMB Review; Comment Request; Planning Guidance and Instructions for Submission of the Strategic... for Submission of the Strategic State Plan and Plan Modifications for Title I of the Workforce Investment Act and Wagner-Peyser Act,'' as proposed to be revised, to the Office of Management and Budget...

SU-E-T-178: Clinical Feasibility of Multi-Leaf Collimator Based Dynamic Wedge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jeong, C; Kwak, J; Ahn, S

2015-06-15

Purpose: A multi-leaf collimator (MLC) based dynamic wedge (MDW), which provide similar dose profile of physical wedge (PW) along x-jaw direction while significant monitor unit (MU) reduction, was developed and investigated for clinical use. Methods: A novel technique was used to create the wedge profile using MLC. A modification was applied to the DICOM-RT format file of the plan made with the PW to replace PW with MDW. The Varian enhanced dynamic wedge profile was used to produce MLC sequence, while the MU of the wedged field was recalculated using PW factor and fluence map. The profiles for all possiblemore » MDWs to substitute PWs were verified in 6/15 MV x-ray irradiations. New plans with MDWs were compared with the original plans in 5 rectal, 5 RT breast and 5 liver cases. Results: The wedge profile of the MDW fields were well matched with those of PWs inside the fields while less scatter than PW out of the fields. For plan comparisons of the clinical cases no significant dose discrepancy was observed between MDW plan and PW’s with the dose volume histograms. The maximum and mean doses in PTVs are agreed within 1.0%. The Result of OARs of MDW plans are slightly improved in the maximum doses (3.22 ∼ 150.4 cGy) and the mean doses (17.18 ∼ 85.52 cGy) on average for all cases while the prescribed doses are 45 Gy for rectal cases, 40 or 45 Gy for liver cases and 50 Gy for breast cases. The MUs of the fields which replace PW with MDW are reduced to 68% of those of PW. Conclusion: We developed a novel dynamic wedge technique with MLC that shows clinical advantage compared to PW.« less

Behavior Modification Techniques. I: Overcorrection. II: Punishment.

ERIC Educational Resources Information Center

Sovner, Robert, Ed.; Hurley, Anne Des Noyers, Ed.

1983-01-01

Two newsletters review the principles and application of two behavior modification techniques with mentally retarded persons: overcorrection and punishment. Overcorrection may be either restitutional, in which the client is made to restore the environment to a far better state than before the inappropriate behavior occurred, or positive practice…

Aircraft Modifications: Assessing the Current State of Air Force Aircraft Modifications and the Implications for Future Military Capability

DTIC Science & Technology

2007-01-25

Air, Space , and Cyberspace." Introduction 3 group production lots together into ’spirals’ or ’increments’. These groupings, as well as an increased...important reference point for this work. The analysis of the modification process presented in this reserach , however, does help shed light on the...planning efforts. Chapter 7- The Future of Aircraft Modifications "Strategy is the art of making use of time and space . I am less concerned about the

Experimental validation of the van Herk margin formula for lung radiation therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ecclestone, Gillian; Heath, Emily; Bissonnette, Jean-Pierre

2013-11-15

Purpose: To validate the van Herk margin formula for lung radiation therapy using realistic dose calculation algorithms and respiratory motion modeling. The robustness of the margin formula against variations in lesion size, peak-to-peak motion amplitude, tissue density, treatment technique, and plan conformity was assessed, along with the margin formula assumption of a homogeneous dose distribution with perfect plan conformity.Methods: 3DCRT and IMRT lung treatment plans were generated within the ORBIT treatment planning platform (RaySearch Laboratories, Sweden) on 4DCT datasets of virtual phantoms. Random and systematic respiratory motion induced errors were simulated using deformable registration and dose accumulation tools available withinmore » ORBIT for simulated cases of varying lesion sizes, peak-to-peak motion amplitudes, tissue densities, and plan conformities. A detailed comparison between the margin formula dose profile model, the planned dose profiles, and penumbra widths was also conducted to test the assumptions of the margin formula. Finally, a correction to account for imperfect plan conformity was tested as well as a novel application of the margin formula that accounts for the patient-specific motion trajectory.Results: The van Herk margin formula ensured full clinical target volume coverage for all 3DCRT and IMRT plans of all conformities with the exception of small lesions in soft tissue. No dosimetric trends with respect to plan technique or lesion size were observed for the systematic and random error simulations. However, accumulated plans showed that plan conformity decreased with increasing tumor motion amplitude. When comparing dose profiles assumed in the margin formula model to the treatment plans, discrepancies in the low dose regions were observed for the random and systematic error simulations. However, the margin formula respected, in all experiments, the 95% dose coverage required for planning target volume (PTV) margin derivation, as defined by the ICRU; thus, suitable PTV margins were estimated. The penumbra widths calculated in lung tissue for each plan were found to be very similar to the 6.4 mm value assumed by the margin formula model. The plan conformity correction yielded inconsistent results which were largely affected by image and dose grid resolution while the trajectory modified PTV plans yielded a dosimetric benefit over the standard internal target volumes approach with up to a 5% decrease in the V20 value.Conclusions: The margin formula showed to be robust against variations in tumor size and motion, treatment technique, plan conformity, as well as low tissue density. This was validated by maintaining coverage of all of the derived PTVs by 95% dose level, as required by the formal definition of the PTV. However, the assumption of perfect plan conformity in the margin formula derivation yields conservative margin estimation. Future modifications to the margin formula will require a correction for plan conformity. Plan conformity can also be improved by using the proposed trajectory modified PTV planning approach. This proves especially beneficial for tumors with a large anterior–posterior component of respiratory motion.« less

Techniques of laparoscopic cholecystectomy: Nomenclature and selection.

PubMed

Haribhakti, Sanjiv P; Mistry, Jitendra H

2015-01-01

There are more than 50 different techniques of laparoscopic cholecystectomy (LC) available in literature mainly due to modifications by surgeons in aim to improve postoperative outcome and cosmesis. These modifications include reduction in port size and/or number than what is used in standard LC. There is no uniform nomenclature to describe these different techniques so that it is not possible to compare the outcomes of different techniques. We brief the advantages and disadvantages of each of these techniques and suggest the situation where particular technique would be useful. We also propose a nomenclature which is easy to remember and apply, so that any future comparison will be possible between the techniques.

Approximate techniques of structural reanalysis

NASA Technical Reports Server (NTRS)

Noor, A. K.; Lowder, H. E.

1974-01-01

A study is made of two approximate techniques for structural reanalysis. These include Taylor series expansions for response variables in terms of design variables and the reduced-basis method. In addition, modifications to these techniques are proposed to overcome some of their major drawbacks. The modifications include a rational approach to the selection of the reduced-basis vectors and the use of Taylor series approximation in an iterative process. For the reduced basis a normalized set of vectors is chosen which consists of the original analyzed design and the first-order sensitivity analysis vectors. The use of the Taylor series approximation as a first (initial) estimate in an iterative process, can lead to significant improvements in accuracy, even with one iteration cycle. Therefore, the range of applicability of the reanalysis technique can be extended. Numerical examples are presented which demonstrate the gain in accuracy obtained by using the proposed modification techniques, for a wide range of variations in the design variables.

Mainstreaming: Sharing Ideas, Strategies, Materials, Techniques.

ERIC Educational Resources Information Center

Hillside School, Cushing, OK.

The manual provides teaching approaches based on a model of least to highest modification of instruction, which may be used for a continuum of special education placements ranging from regular classroom through hospital settings. The first section on adaptive techniques (requiring the least modification) includes suggestions to adjust time for…

Two Student Self-Management Techniques Applied to Data-Based Program Modification.

ERIC Educational Resources Information Center

Wesson, Caren

Two student self-management techniques, student charting and student selection of instructional activities, were applied to ongoing data-based program modification. Forty-two elementary school resource room students were assigned randomly (within teacher) to one of three treatment conditions: Teacher Chart-Teacher Select Instructional Activities…

Planning for coordinated space and ground-based ionospheric modification experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, M.C.

1990-10-01

The planning and conducting of coordinated space and ground-based ionospheric modification experiments are discussed. The purpose of these experiments is to investigate (1) the nonlinear VLF wave interaction with the ionospheric plasmas, and (2) the nonlinear propagation of VLF waves in the HF-modified ionosphere. It is expected that the HY-induced ionospheric density striations can render the nonlinear mode conversion of VLF waves into lower hybrid waves. Lower hybrid waves can also be excited parametrically by the VLF waves in the absence of the density striations if the VLF waves are intense enough. Laboratory experiments are planned for crosschecking the resultsmore » obtained from the field experiments.« less

Technical aspects of the integration of three-dimensional treatment planning dose parameters (GEC-ESTRO Working Group) into pre-implant planning for LDR gynecological interstitial brachytherapy.

PubMed

Chi, A; Gao, M; Nguyen, N P; Albuquerque, K

2009-06-01

This study investigates the technical feasibility of pre-implant image-based treatment planning for LDR GYN interstitial brachytherapy(IB) based on the GEC-ESTRO guidelines. Initially, a virtual plan is generated based on the prescription dose and GEC-ESTRO defined OAR dose constraints with a pre-implant CT. After the actual implant, a regular diagnostic CT was obtained and fused with our pre-implant scan/initial treatment plan in our planning software. The Flexi-needle position changes, and treatment plan modifications were made if needed. Dose values were normalized to equivalent doses in 2 Gy fractions (LQED 2 Gy) derived from the linear-quadratic model with alpha/beta of 3 for late responding tissues and alpha/beta of 10 for early responding tissues. D(90) to the CTV, which was gross tumor (GTV) at the time of brachytherapy with a margin to count for microscopic disease, was 84.7 +/- 4.9% of the prescribed dose. The OAR doses were evaluated by D(2cc) (EBRT+IB). Mean D(2cc) values (LQED(2Gy)) for the rectum, bladder, sigmoid, and small bowel were the following: 63.7 +/- 8.4 Gy, 61.2 +/- 6.9 Gy, 48.0 +/- 3.5 Gy, and 49.9 +/- 4.2 Gy. This study confirms the feasibility of applying the GEC-ESTRO recommended dose parameters in pre-implant CT-based treatment planning in GYN IB. In the process, this pre-implant technique also demonstrates a good approximation of the target volume dose coverage, and doses to the OARs.

40 CFR 790.50 - Submission of study plans.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 31 2010-07-01 2010-07-01 true Submission of study plans. 790.50..., Enforcement, and Modification of Test Rules § 790.50 Submission of study plans. (a) Who must submit study... of a single phase test rule as described in § 790.40(b)(1) must submit study plans for those tests...

40 CFR 790.50 - Submission of study plans.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 32 2011-07-01 2011-07-01 false Submission of study plans. 790.50..., Enforcement, and Modification of Test Rules § 790.50 Submission of study plans. (a) Who must submit study... of a single phase test rule as described in § 790.40(b)(1) must submit study plans for those tests...

40 CFR 60.2900 - When must I submit my waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false When must I submit my waste management... Modification or Reconstruction is Commenced on or After June 16, 2006 Waste Management Plan § 60.2900 When must I submit my waste management plan? You must submit a waste management plan prior to commencing...

40 CFR 60.2900 - When must I submit my waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false When must I submit my waste management... Modification or Reconstruction is Commenced on or After June 16, 2006 Waste Management Plan § 60.2900 When must I submit my waste management plan? You must submit a waste management plan prior to commencing...

36 CFR 223.113 - Modification of contracts to prevent environmental damage or to conform to forest plans.

Code of Federal Regulations, 2010 CFR

2010-07-01

... environmental damage or to conform to forest plans. Timber sale contract, permits, and other such instruments... revisions of land and resource management plans adopted subsequent to award or issuance of a timber sale... prevent environmental damage or to conform to forest plans. 223.113 Section 223.113 Parks, Forests, and...

34. Site Plan: Fort Custer Air Force Station, Fort Custer, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. Site Plan: Fort Custer Air Force Station, Fort Custer, Michigan, Modification of Electrical Distribution, General Site Plan, USACOE, no date. - Fort Custer Military Reservation, P-67 Radar Station, .25 mile north of Dickman Road, east of Clark Road, Battle Creek, Calhoun County, MI

MAP-IT: A Practical Tool for Planning Complex Behavior Modification Interventions.

PubMed

Hansen, Sylvia; Kanning, Martina; Lauer, Romy; Steinacker, Jürgen M; Schlicht, Wolfgang

2017-09-01

Health research often aims to prevent noncommunicable diseases and to improve individual and public health by discovering intervention strategies that are effective in changing behavior and/or environments that are detrimental to one's health. Ideally, findings from original research support practitioners in planning and implementing effective interventions. Unfortunately, interventions often fail to overcome the translational block between science and practice. They often ignore theoretical knowledge, overlook empirical evidence, and underrate the impact of the environment. Accordingly, sustainable changes in individual behavior and/or the environment are difficult to achieve. Developing theory-driven and evidence-based interventions in the real world is a complex task. Existing implementation frameworks and theories often do not meet the needs of health practitioners. The purpose of this article is to synthesize existing frameworks and to provide a tool, the Matrix Assisting Practitioner's Intervention Planning Tool (MAP-IT), that links research to practice and helps practitioners to design multicomponent interventions. In this article, we use physical activity of older adults as an example to explain the rationale of MAP-IT. In MAP-IT, individual as well as environmental mechanisms are listed and behavior change techniques are linked to these mechanisms and to intervention components. MAP-IT is theory-driven and evidence-based. It is time-saving and helpful for practitioners when planning complex interventions.

A tandem regression-outlier analysis of a ligand cellular system for key structural modifications around ligand binding.

PubMed

Lin, Ying-Ting

2013-04-30

A tandem technique of hard equipment is often used for the chemical analysis of a single cell to first isolate and then detect the wanted identities. The first part is the separation of wanted chemicals from the bulk of a cell; the second part is the actual detection of the important identities. To identify the key structural modifications around ligand binding, the present study aims to develop a counterpart of tandem technique for cheminformatics. A statistical regression and its outliers act as a computational technique for separation. A PPARγ (peroxisome proliferator-activated receptor gamma) agonist cellular system was subjected to such an investigation. Results show that this tandem regression-outlier analysis, or the prioritization of the context equations tagged with features of the outliers, is an effective regression technique of cheminformatics to detect key structural modifications, as well as their tendency of impact to ligand binding. The key structural modifications around ligand binding are effectively extracted or characterized out of cellular reactions. This is because molecular binding is the paramount factor in such ligand cellular system and key structural modifications around ligand binding are expected to create outliers. Therefore, such outliers can be captured by this tandem regression-outlier analysis.

Computer Aided Process Planning (CAPP): The User Interface for the Fabrication Module of the Rapid Design System

DTIC Science & Technology

1991-01-01

plan. The Fabrication Planning Module automatically creates a plan using information from the Feature Based Design Environment (FBDE) of the RDS. It...llll By using the user Interface, the final process plan can be modified in many different ways. The translation of a design feature to a more...for the review and modification of a process plan. The Fabrication Planning Module automatically creates a plan using information from the Feature Based

Modifications to ELIM-COMPLIP and MOSLS for Mobilization Strength Planning and Management for Enlisted Personnel.

DTIC Science & Technology

1982-05-01

AD-AllA 143 GENERAL RESEARCH CORP MCLEAN VA MANAGEMENT SYSTEMS DIV F/G 5/9 MoD IFI CATI ONS TO ELIM-COMPL.IP AND MOSLS FOR MOBILIZATION STRENG--ETC...111111____22 I Report 1257-02-CR I Modifications I To ELIM-COMPLIP and MOSLS for I ’ Mobilization Strength Planning and Management -~ For Enlisted...Personnel By: I K.D. Midlamn, Project Manage W.E. Bartlett E. Bergs B.W. Holz M.J. Maloney I May 1982 MANAGEMENT SYSTEMS DIVISIONI GENERAL ( RESEARCH

40 CFR 60.2055 - What is a waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What is a waste management plan? 60.2055 Section 60.2055 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... Which Modification or Reconstruction Is Commenced on or After June 1, 2001 Waste Management Plan § 60...

24 CFR 597.300 - HUD action and review of nominations for designation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR COMMUNITY PLANNING AND DEVELOPMENT... and must be accompanied by a strategic plan, as required by § 597.200(c), and the certifications... evaluation. (d) Modification of the strategic plan, boundaries of nominated urban areas, and/or period during...

Achieving a predictable 24-hour return to normal activities after breast augmentation: part II. Patient preparation, refined surgical techniques, and instrumentation.

PubMed

Tebbetts, John B

2006-12-01

The goal of this study was to develop practices that would allow patients undergoing subpectoral augmentation to predictably return to full normal activities within 24 hours after the operation, free of postoperative adjuncts. Part I of this study used motion and time study principles to reduce operative times, medication dosages, perioperative morbidity, and recovery times in augmentation mammaplasty. Part II of the study focuses on details of patient education, preoperative planning, instrumentation, and surgical technique modifications that were identified, modified, and implemented to achieve the results reported in part I. Two groups of 16 patients each (groups 1 and 2) were studied retrospectively for comparison to a third group of 627 patients (group 3) studied prospectively. Patients in group 1 had axillary partial retropectoral breast augmentations in 1982-1983, using dissociative anesthesia, blunt instrument implant pocket dissection, and Dow Corning, double-lumen implants containing 20 mg of methylprednisolone and 20 cc of saline in the outer lumen of the implants. Patients in group 2 (1990) had inframammary, retromammary augmentations by using a combination of blunt and electrocautery dissection, Surgitek Replicon polyurethane-covered, silicone gel-filled implants, and general endotracheal anesthesia. Patients in group 3 (1998 to 2001, n = 627) had inframammary partial retropectoral, inframammary retromammary, and axillary partial retropectoral augmentations under general endotracheal anesthesia. Refined practices and surgical techniques from studies of groups 1 and 2 were applied in group 3. Videotapes from operative procedures of groups 1 and 2 were analyzed with macromotion and micromotion study principles, and tables of events were formulated for each move during the operation for all personnel in the operating room. Extensive details of surgical technique were examined and reexamined in 13 different stages by using principles of motion and time studies described in part I of this study to maximize efficiency without any change in quality. Unnecessary or unproductive motions and techniques were progressively eliminated, and essential, productive techniques were streamlined to eliminate wasted time and motion. Instrumentation and surgical techniques were evaluated in detail and modified to minimize bleeding and tissue trauma. Detailed data were presented in part I of this study that document shorter operative times, recovery times, time to discharge home, and time to return to normal activities. This part focuses on the patient education, preoperative planning, instrumentation, and surgical technique changes that were implemented on the basis of the findings in part I of the study. More extensive patient information integrated with staged informed consent resulted in a more in formed and confident patient. Applying motion and time study principles to analysis and refinement of instrumentation and surgical techniques resulted in a substantial reduction in perioperative morbidity and a simpler, shorter 24-hour return to full normal activity for 96 percent of the patients undergoing breast augmentation in group 3 compared with groups 1 and 2. More than 96 percent of patients in group 3 were able to return to normal activities, lift their arms above their heads, lift normal-weight objects, and drive their car within 24 hours after their partial retropectoral breast augmentation. Patient education, preoperative planning, instrumentation, and surgical technique modifications based on motion and time study video analyses reduced surgical trauma and bleeding, reduced perioperative morbidity, and allowed 96 percent of 627 breast augmentation patients in group 3 a predictable return to full, normal activity in 24 hours or less. Specific surgical factors that contributed to these results included (1) prospective hemostasis techniques with a zero tolerance for even the smallest amount of bleeding, (2) strict "no-touch" techniques for periosteum and perichondrium, (3) eliminating all blunt dissection, (4) performing all dissection under direct vision, (5) modified and simplified instrumentation, and (6) optimal use of muscle relaxants during subpectoral dissection.

Achieving a predictable 24-hour return to normal activities after breast augmentation: Part II. Patient preparation, refined surgical techniques, and instrumentation.

PubMed

Tebbetts, John B

2002-01-01

The goal of this study was to develop practices that would allow patients undergoing subpectoral augmentation to predictably return to full normal activities within 24 hours after the operation, free of postoperative adjuncts. Part I of this study used motion and time study principles to reduce operative times, medication dosages, perioperative morbidity, and recovery times in augmentation mammaplasty. Part II of the study focuses on details of patient education, preoperative planning, instrumentation, and surgical technique modifications that were identified, modified, and implemented to achieve the results reported in part I. Two groups of 16 patients each (groups 1 and 2) were studied retrospectively for comparison to a third group of 627 patients (group 3) studied prospectively. Patients in group 1 had axillary partial retropectoral breast augmentations in 1982-1983, using dissociative anesthesia, blunt instrument implant pocket dissection, and Dow Corning, double-lumen implants containing 20 mg of methylprednisolone and 20 cc of saline in the outer lumen of the implants. Patients in group 2 (1990) had inframammary, retromammary augmentations by using a combination of blunt and electrocautery dissection, Surgitek Replicon polyurethane-covered, silicone gel-filled implants, and general endotracheal anesthesia. Patients in group 3 (1998 to 2001, n = 627) had inframammary partial retropectoral, inframammary retromammary, and axillary partial retropectoral augmentations under general endotracheal anesthesia. Refined practices and surgical techniques from studies of groups 1 and 2 were applied in group 3. Videotapes from operative procedures of groups 1 and 2 were analyzed with macromotion and micromotion study principles, and tables of events were formulated for each move during the operation for all personnel in the operating room. Extensive details of surgical technique were examined and reexamined in 13 different stages by using principles of motion and time studies described in part I of this study to maximize efficiency without any change in quality. Unnecessary or unproductive motions and techniques were progressively eliminated, and essential, productive techniques were streamlined to eliminate wasted time and motion. Instrumentation and surgical techniques were evaluated in detail and modified to minimize bleeding and tissue trauma. Detailed data were presented in part I of this study that document shorter operative times, recovery times, time to discharge home, and time to return to normal activities. This part focuses on the patient education, preoperative planning, instrumentation, and surgical technique changes that were implemented on the basis of the findings in part I of the study. More extensive patient information integrated with staged informed consent resulted in a more informed and confident patient. Applying motion and time study principles to analysis and refinement of instrumentation and surgical techniques resulted in a substantial reduction in perioperative morbidity and a simpler, shorter 24-hour return to full normal activity for 96 percent of the patients undergoing breast augmentation in group 3 compared with groups 1 and 2. More than 96 percent of patients in group 3 were able to return to normal activities, lift their arms above their heads, lift normal-weight objects, and drive their car within 24 hours after their partial retropectoral breast augmentation. Patient education, preoperative planning, instrumentation, and surgical technique modifications based on motion and time study video analyses reduced surgical trauma and bleeding, reduced perioperative morbidity, and allowed 96 percent of 627 breast augmentation patients in group 3 a predictable return to full, normal activity in 24 hours or less. Specific surgical factors that contributed to these results included (1) prospective hemostasis techniques with a zero tolerance for even the smallest amount of bleeding, (2) strict "no-touch" techniques for periosteum and perichondrium, (3) eliminating all blunt dissection, (4) performing all dissection under direct vision, (5) modified and simplified instrumentation, and (6) optimal use of muscle relaxants during subpectoral dissection.

A basic review on the inferior alveolar nerve block techniques.

PubMed

Khalil, Hesham

2014-01-01

The inferior alveolar nerve block is the most common injection technique used in dentistry and many modifications of the conventional nerve block have been recently described in the literature. Selecting the best technique by the dentist or surgeon depends on many factors including the success rate and complications related to the selected technique. Dentists should be aware of the available current modifications of the inferior alveolar nerve block techniques in order to effectively choose between these modifications. Some operators may encounter difficulty in identifying the anatomical landmarks which are useful in applying the inferior alveolar nerve block and rely instead on assumptions as to where the needle should be positioned. Such assumptions can lead to failure and the failure rate of inferior alveolar nerve block has been reported to be 20-25% which is considered very high. In this basic review, the anatomical details of the inferior alveolar nerve will be given together with a description of its both conventional and modified blocking techniques; in addition, an overview of the complications which may result from the application of this important technique will be mentioned.

A basic review on the inferior alveolar nerve block techniques

PubMed Central

Khalil, Hesham

2014-01-01

The inferior alveolar nerve block is the most common injection technique used in dentistry and many modifications of the conventional nerve block have been recently described in the literature. Selecting the best technique by the dentist or surgeon depends on many factors including the success rate and complications related to the selected technique. Dentists should be aware of the available current modifications of the inferior alveolar nerve block techniques in order to effectively choose between these modifications. Some operators may encounter difficulty in identifying the anatomical landmarks which are useful in applying the inferior alveolar nerve block and rely instead on assumptions as to where the needle should be positioned. Such assumptions can lead to failure and the failure rate of inferior alveolar nerve block has been reported to be 20-25% which is considered very high. In this basic review, the anatomical details of the inferior alveolar nerve will be given together with a description of its both conventional and modified blocking techniques; in addition, an overview of the complications which may result from the application of this important technique will be mentioned. PMID:25886095

40 CFR 52.56 - Review of new sources and modifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... 52.56 Section 52.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Alabama § 52.56 Review of new... and modifications in nonattainment areas are approved on condition that the State submit any necessary...

40 CFR 52.56 - Review of new sources and modifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... 52.56 Section 52.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Alabama § 52.56 Review of new... and modifications in nonattainment areas are approved on condition that the State submit any necessary...

40 CFR 52.56 - Review of new sources and modifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... 52.56 Section 52.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Alabama § 52.56 Review of new... and modifications in nonattainment areas are approved on condition that the State submit any necessary...

22. Photocopy of engineering drawing. MODIFICATION TO LAUNCH COMPLEX 17 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. Photocopy of engineering drawing. MODIFICATION TO LAUNCH COMPLEX 17 MOBILE SERVICE TOWER 'A'-MECHANICAL, PROPULSION DRIVE TRUCKS AND KEY PLAN, MARCH 1967. - Cape Canaveral Air Station, Launch Complex 17, Facility 28416, East end of Lighthouse Road, Cape Canaveral, Brevard County, FL

77 FR 58983 - New England Fishery Management Council; Public Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-25

...-0492. SUPPLEMENTARY INFORMATION: The Habitat Advisory Panel and Plan Development Team will review and further develop alternatives for Omnibus Essential Fish Habitat Amendment 2. Related to gear modification options for Habitat Management Areas, they will discuss ground cable modification options in general and...

Techniques of laparoscopic cholecystectomy: Nomenclature and selection

PubMed Central

Haribhakti, Sanjiv P.; Mistry, Jitendra H.

2015-01-01

There are more than 50 different techniques of laparoscopic cholecystectomy (LC) available in literature mainly due to modifications by surgeons in aim to improve postoperative outcome and cosmesis. These modifications include reduction in port size and/or number than what is used in standard LC. There is no uniform nomenclature to describe these different techniques so that it is not possible to compare the outcomes of different techniques. We brief the advantages and disadvantages of each of these techniques and suggest the situation where particular technique would be useful. We also propose a nomenclature which is easy to remember and apply, so that any future comparison will be possible between the techniques. PMID:25883450

Graphic/symbol segmentation for Group 4 facsimile systems

NASA Astrophysics Data System (ADS)

Deutermann, A. R.

1982-04-01

The purpose of this study was to examine possible techniques for and symbol areas, and assemble a code that represents the entire document. Parameters to be considered include compression, commonality with facsimile and TELETEX* transmissions, and complexity of implementation. Six segmentation technique were selected for analysis. The techniques were designed to differ from each other as much as possible, so as to display a wide variety of characteristics. For each technique, many minor modifications would be possible, but it is not expected that these modifications would alter the conclusions drawn from the study.

Space Shuttle orbiter modifications to support Space Station Freedom

NASA Technical Reports Server (NTRS)

Segert, Randall; Lichtenfels, Allyson

1992-01-01

The Space Shuttle will be the primary vehicle to support the launch, assembly, and maintenance of the Space Station Freedom (SSF). In order to accommodate this function, the Space Shuttle orbiter will require significant modifications. These modifications are currently in development in the Space Shuttle Program. The requirements for the planned modifications to the Space Shuttle orbiter are dependent on the design of the SSF. Therefore, extensive coordination is required with the Space Station Freedom Program (SSFP) in order to identify requirements and resolve integration issues. This paper describes the modifications to the Space Shuttle orbiter required to support SSF assembly and operations.

Planning Coverage Campaigns for Mission Design and Analysis: Clasp for the Proposed DESDynI Mission

NASA Technical Reports Server (NTRS)

Knight, Russell; McLaren, David; Hu, Steven

2012-01-01

Mission design and analysis present challenges in that almost all variables are in constant flux, yet the goal is to achieve an acceptable level of performance against a concept of operations, which might also be in flux. To increase responsiveness, our approach is to use automated planning tools that allow for the continual modification of spacecraft, ground system, staffing, and concept of operations while returning metrics that are important to mission evaluation, such as area covered, peak memory usage, and peak data throughput. We have applied this approach to DESDynI (Deformation, Ecosystem Structure, and Dynamics of Ice) mission design concept using the CLASP (Compressed Large-scale Activity Scheduler/Planner) planning system [7], but since this adaptation many techniques have changed under the hood for CLASP and the DESDynI mission concept has undergone drastic changes, including that it has been renamed the Earth Radar Mission. Over the past two years, we have run more than fifty simulations with the CLASP-DESDynI adaptation, simulating different mission scenarios with changing parameters including targets, swaths, instrument modes, and data and downlink rates. We describe the evolution of simulations through the DESDynI MCR (Mission Concept Review) and afterwards.

WIPP Remote-Handled TRU Waste Program Update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Most, W.; Kehrman, B.

2006-07-01

There are two major regulatory approval milestones necessary in order to commence disposal operations for remote-handled transuranic (RH TRU) waste at the Waste Isolation Pilot Plant (WIPP)-the RH TRU hazardous waste permit modification request [1] and the radiological characterization plan [2]. One of those milestones has been achieved. The US Environmental Protection Agency (EPA) issued its final decision to approve the Department of Energy's (DOE) RH TRU radiological characterization plan along with the RH TRU Waste Characterization Program Implementation Plan [3], on March 26, 2004. The RH TRU hazardous waste permit modification request still awaits agency approval. In EPA's decisionmore » to approve the DOE's RH TRU radiological characterization plan, the EPA also set forth the process for approving site-specific RH TRU waste characterization programs. Included in the March 29, 2005, RH TRU second Notice of Deficiency [4] (NOD) on the Class 3 Permit Modification Request for RH TRU Waste, the New Mexico Environment Department (NMED) requested that the Permittees combine their responses for the RH TRU Waste NOD with the Section 311 permit modification request NOD. The Combined Response Document was submitted April 28, 2005 [5]. Another NOD [6] was issued by the NMED on September 1, 2005, to clarify the Permittees' proposal and submit these clarifications to the administrative record. Combining both the chap. 311 [7] and RH TRU waste permit modification requests allows for both the regulator and Permittees to expedite action on the modification requests. The Combined Response Document preserves human resources and costs by having only one administrative process for both modification requests. Facility readiness requirements of the RH TRU waste final permit [8] must be implemented to declare that the WIPP is ready to receive RH TRU waste for storage and disposal. To demonstrate readiness, the WIPP is preparing for an Operational Readiness Review (ORR) of the RH TRU waste management equipment, system, and procedures. Required by DOE Order, the ORR demonstrates the capability of managing RH TRU waste. The Management and Operating Contractor (MOC) for the WIPP must first perform a Line Management Assessment. Upon successful completion of the Line Management Assessment, the MOC performs the Contractor ORR and presents the results to the local DOE office. At that time, the local DOE office performs its own ORR to declare readiness to DOE Headquarters. (authors)« less

7 CFR 634.26 - Contract modifications.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., DEPARTMENT OF AGRICULTURE LONG TERM CONTRACTING RURAL CLEAN WATER PROGRAM Participant RCWP Contracts § 634.26... thereof, or to accomplish equitable treatment with respect to other conservation, land-use, or water... water-quality plan. A contract may be modified only if it is determined that such modifications are...

7 CFR 634.26 - Contract modifications.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., DEPARTMENT OF AGRICULTURE LONG TERM CONTRACTING RURAL CLEAN WATER PROGRAM Participant RCWP Contracts § 634.26... thereof, or to accomplish equitable treatment with respect to other conservation, land-use, or water... water-quality plan. A contract may be modified only if it is determined that such modifications are...

7 CFR 634.26 - Contract modifications.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., DEPARTMENT OF AGRICULTURE LONG TERM CONTRACTING RURAL CLEAN WATER PROGRAM Participant RCWP Contracts § 634.26... thereof, or to accomplish equitable treatment with respect to other conservation, land-use, or water... water-quality plan. A contract may be modified only if it is determined that such modifications are...

7 CFR 634.26 - Contract modifications.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., DEPARTMENT OF AGRICULTURE LONG TERM CONTRACTING RURAL CLEAN WATER PROGRAM Participant RCWP Contracts § 634.26... thereof, or to accomplish equitable treatment with respect to other conservation, land-use, or water... water-quality plan. A contract may be modified only if it is determined that such modifications are...

Project Success for the SLD Child, Curriculum Modification.

ERIC Educational Resources Information Center

Owens, Jean

The curriculum modification guide, developed by project success (Nebraska) through a Title III grant for language disabled elementary level students, contains suggested activities and instructional materials to be used in units of art, health, mathematics, music, science, and social studies. Explained are program planning, criteria for selecting…

40 CFR 233.36 - Modification, suspension or revocation of permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... has been submitted to the Director; (iv) Provide for minor modification of project plans that do not... appropriately regulated by individual permits; (4) Circumstances relating to the authorized activity have... cessation of any discharge controlled by the permit; (5) Any significant information relating to the...

76 FR 51058 - Petitions for Modification of Application of Existing Mandatory Safety Standards

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-17

... CFR part 48 training plan to the Metal/ Nonmetal Safety and Health District Manager. In addition to... DEPARTMENT OF LABOR Mine Safety and Health Administration Petitions for Modification of Application of Existing Mandatory Safety Standards AGENCY: Mine Safety and Health Administration, Labor...

7 CFR 634.26 - Contract modifications.

Code of Federal Regulations, 2010 CFR

2010-01-01

...-quality programs. (b) Requirements of active contracts may be waived or modified by the administering... water-quality plan. A contract may be modified only if it is determined that such modifications are... when items of work are accomplished prior to scheduled completion or within 1 year following the year...

40 CFR 267.112 - What procedures must I follow?

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (1) Events leading to a change in the closure plan, and therefore requiring a modification, may include: (i) A change in the operating plan or facility design; (ii) A change in the expected year of...

State of emergency preparedness for US health insurance plans.

PubMed

Merchant, Raina M; Finne, Kristen; Lardy, Barbara; Veselovskiy, German; Korba, Caey; Margolis, Gregg S; Lurie, Nicole

2015-01-01

Health insurance plans serve a critical role in public health emergencies, yet little has been published about their collective emergency preparedness practices and policies. We evaluated, on a national scale, the state of health insurance plans' emergency preparedness and policies. A survey of health insurance plans. We queried members of America's Health Insurance Plans, the national trade association representing the health insurance industry, about issues related to emergency preparedness issues: infrastructure, adaptability, connectedness, and best practices. Of 137 health insurance plans queried, 63% responded, representing 190.6 million members and 81% of US plan enrollment. All respondents had emergency plans for business continuity, and most (85%) had infrastructure for emergency teams. Some health plans also have established benchmarks for preparedness (eg, response time). Regarding adaptability, 85% had protocols to extend claim filing time and 71% could temporarily suspend prior medical authorization rules. Regarding connectedness, many plans shared their contingency plans with health officials, but often cited challenges in identifying regulatory agency contacts. Some health insurance plans had specific policies for assisting individuals dependent on durable medical equipment or home healthcare. Many plans (60%) expressed interest in sharing best practices. Health insurance plans are prioritizing emergency preparedness. We identified 6 policy modifications that health insurance plans could undertake to potentially improve healthcare system preparedness: establishing metrics and benchmarks for emergency preparedness; identifying disaster-specific policy modifications, enhancing stakeholder connectedness, considering digital strategies to enhance communication, improving support and access for special-needs individuals, and developing regular forums for knowledge exchange about emergency preparedness.

7 CFR 25.204 - Evaluation of the strategic plan.

Code of Federal Regulations, 2011 CFR

2011-01-01

... pertaining to the plan and the proposed area and may, as part of that request, suggest modifications to the... review each plan submitted in terms of the four equally weighted principal objectives, and of such other... and ensuring that all residents will have equal access to that housing is contained in the strategic...

7 CFR 25.204 - Evaluation of the strategic plan.

Code of Federal Regulations, 2012 CFR

2012-01-01

... pertaining to the plan and the proposed area and may, as part of that request, suggest modifications to the... review each plan submitted in terms of the four equally weighted principal objectives, and of such other... and ensuring that all residents will have equal access to that housing is contained in the strategic...

7 CFR 25.204 - Evaluation of the strategic plan.

Code of Federal Regulations, 2014 CFR

2014-01-01

... pertaining to the plan and the proposed area and may, as part of that request, suggest modifications to the... review each plan submitted in terms of the four equally weighted principal objectives, and of such other... and ensuring that all residents will have equal access to that housing is contained in the strategic...

75 FR 45652 - Notice of Intent To Prepare an Environmental Impact Statement and Resource Management Plan...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-03

... Management Plan Amendment for the Proposed Modification to the Thompson Creek Mine Plan of Operations... DEPARTMENT OF THE INTERIOR Bureau of Land Management [LLIDI03000.L71220000.EX0000.XXXX... AGENCY: Bureau of Land Management, Interior. ACTION: Notice of Intent. SUMMARY: In compliance with the...

75 FR 6338 - Approval and Promulgation of Implementation Plans; Georgia: State Implementation Plan Revision

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-09

... revisions include multiple modifications to Georgia's Air Quality Rules found at Chapter 391-3-1. These...: Ms. Lynorae Benjamin, Regulatory Development Section, Air Planning Branch, Air, Pesticides and Toxics...-8960. The telephone number is (404) 562-9042. Ms. Harder can also be reached via electronic mail at...

48 CFR 243.204-70-7 - Plans and reports.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Plans and reports. 243.204-70-7 Section 243.204-70-7 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT CONTRACT MODIFICATIONS Change Orders 243.204-70-7 Plans and reports. To provide for enhanced...

48 CFR 243.204-70-7 - Plans and reports.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Plans and reports. 243.204-70-7 Section 243.204-70-7 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT CONTRACT MODIFICATIONS Change Orders 243.204-70-7 Plans and reports. To provide for enhanced...

Butanol / Honda CRADA Report

DTIC Science & Technology

2015-02-01

study developed a test plan to test BU16 in CG boats, assessing boat performance, and the modifications required to use the fuel. The third study (and...current project) executed this test plan to quantify implementation issues, benefits and impacts of using the alternative fuel in CG boats under...4  2.2  Project 2: Test Plan Development

77 FR 12074 - Endangered and Threatened Wildlife and Plants; Receipt of Application for Modification of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-28

... Incidental Take Permit; Availability of Proposed Low-Effect Habitat Conservation Plan; Mosaic Fertilizer, LLC... proposed habitat conservation plan (HCP), as well as on our preliminary determination that the plan... 24 years to 41 years, changing the boundary of the conservation easement placed on the property used...

Treating Retentive Encopresis: Dietary Modification and Behavioral Techniques.

ERIC Educational Resources Information Center

Nabors, Laura; Morgan, Sam B.

1995-01-01

A home-based contingency management program, consisting of diet modification, laxatives, correction for soiling accidents, stimulus control training, and positive reinforcement, was implemented for treatment of a 4-year-old encopretic male. The findings provide evidence supporting the effectiveness of dietary modification combined with behavior…

The double stapling technique for low anterior resection. Results, modifications, and observations.

PubMed Central

Griffen, F D; Knight, C D; Whitaker, J M; Knight, C D

1990-01-01

Since the introduction of the end-to-end anastomosis (EEA) stapler for rectal reconstruction, we have used a modification of the conventional technique in which the lower rectal segment is closed with the linear stapler (TA-55) and the anastomosis is performed using the EEA instrument across the linear staple line (double stapling technique). Our experience with this procedure includes stapled colorectal anastomoses in 75 patients and is the basis for the report. This review presents the details and advantages of the technique and the results. Complications include two patients with anastomotic leak (2.7%), and two with stenosis that required treatment (2.7%). Protective colostomy was not done in this series. There were no deaths. Our experience and that of others suggests that this modification of the EEA technique can allow a lower anastomosis in some patients, and that it can be done with greater safety and facility. Images Fig. 1. Fig. 2. Fig. 3. Fig. 4. Fig. 5. Fig. 6. PMID:2357137

Galileo mission planning for Low Gain Antenna based operations

NASA Technical Reports Server (NTRS)

Gershman, R.; Buxbaum, K. L.; Ludwinski, J. M.; Paczkowski, B. G.

1994-01-01

The Galileo mission operations concept is undergoing substantial redesign, necessitated by the deployment failure of the High Gain Antenna, while the spacecraft is on its way to Jupiter. The new design applies state-of-the-art technology and processes to increase the telemetry rate available through the Low Gain Antenna and to increase the information density of the telemetry. This paper describes the mission planning process being developed as part of this redesign. Principal topics include a brief description of the new mission concept and anticipated science return (these have been covered more extensively in earlier papers), identification of key drivers on the mission planning process, a description of the process and its implementation schedule, a discussion of the application of automated mission planning tool to the process, and a status report on mission planning work to date. Galileo enhancements include extensive reprogramming of on-board computers and substantial hard ware and software upgrades for the Deep Space Network (DSN). The principal mode of operation will be onboard recording of science data followed by extended playback periods. A variety of techniques will be used to compress and edit the data both before recording and during playback. A highly-compressed real-time science data stream will also be important. The telemetry rate will be increased using advanced coding techniques and advanced receivers. Galileo mission planning for orbital operations now involves partitioning of several scarce resources. Particularly difficult are division of the telemetry among the many users (eleven instruments, radio science, engineering monitoring, and navigation) and allocation of space on the tape recorder at each of the ten satellite encounters. The planning process is complicated by uncertainty in forecast performance of the DSN modifications and the non-deterministic nature of the new data compression schemes. Key mission planning steps include quantifying resource or capabilities to be allocated, prioritizing science observations and estimating resource needs for each, working inter-and intra-orbit trades of these resources among the Project elements, and planning real-time science activity. The first major mission planning activity, a high level, orbit-by-orbit allocation of resources among science objectives, has already been completed; and results are illustrated in the paper. To make efficient use of limited resources, Galileo mission planning will rely on automated mission planning tools capable of dealing with interactions among time-varying downlink capability, real-time science and engineering data transmission, and playback of recorded data. A new generic mission planning tool is being adapted for this purpose.

Galileo mission planning for Low Gain Antenna based operations

NASA Astrophysics Data System (ADS)

Gershman, R.; Buxbaum, K. L.; Ludwinski, J. M.; Paczkowski, B. G.

1994-11-01

The Galileo mission operations concept is undergoing substantial redesign, necessitated by the deployment failure of the High Gain Antenna, while the spacecraft is on its way to Jupiter. The new design applies state-of-the-art technology and processes to increase the telemetry rate available through the Low Gain Antenna and to increase the information density of the telemetry. This paper describes the mission planning process being developed as part of this redesign. Principal topics include a brief description of the new mission concept and anticipated science return (these have been covered more extensively in earlier papers), identification of key drivers on the mission planning process, a description of the process and its implementation schedule, a discussion of the application of automated mission planning tool to the process, and a status report on mission planning work to date. Galileo enhancements include extensive reprogramming of on-board computers and substantial hard ware and software upgrades for the Deep Space Network (DSN). The principal mode of operation will be onboard recording of science data followed by extended playback periods. A variety of techniques will be used to compress and edit the data both before recording and during playback. A highly-compressed real-time science data stream will also be important. The telemetry rate will be increased using advanced coding techniques and advanced receivers. Galileo mission planning for orbital operations now involves partitioning of several scarce resources. Particularly difficult are division of the telemetry among the many users (eleven instruments, radio science, engineering monitoring, and navigation) and allocation of space on the tape recorder at each of the ten satellite encounters. The planning process is complicated by uncertainty in forecast performance of the DSN modifications and the non-deterministic nature of the new data compression schemes. Key mission planning steps include quantifying resource or capabilities to be allocated, prioritizing science observations and estimating resource needs for each, working inter-and intra-orbit trades of these resources among the Project elements, and planning real-time science activity. The first major mission planning activity, a high level, orbit-by-orbit allocation of resources among science objectives, has already been completed; and results are illustrated in the paper. To make efficient use of limited resources, Galileo mission planning will rely on automated mission planning tools capable of dealing with interactions among time-varying downlink capability, real-time science and engineering data transmission, and playback of recorded data. A new generic mission planning tool is being adapted for this purpose.

Role of Islam in the management of Psychiatric disorders

PubMed Central

Sabry, Walaa M.; Vohra, Adarsh

2013-01-01

With the significant growth of the Muslim population all over the world, there exists a corresponding increase in the need for mental health services that suit this group of patients. Research demonstrates the effectiveness of the integration of spirituality and religiosity into psychotherapy and how religious beliefs could affect the management plans. This article discusses the impact of various beliefs in the Islamic faith on the bio-psychosocial model for the management of different psychiatric disorders including focusing on the modification of psychotherapeutic techniques as cognitive restructuring. It also shows other types of therapies such as music therapy, meditation therapy, and aromatherapy. The main emphasis remains to ensure that Muslim psychiatric patients get ethical, acceptable, and effective treatment. PMID:23858256

Efficient computational nonlinear dynamic analysis using modal modification response technique

NASA Astrophysics Data System (ADS)

Marinone, Timothy; Avitabile, Peter; Foley, Jason; Wolfson, Janet

2012-08-01

Generally, structural systems contain nonlinear characteristics in many cases. These nonlinear systems require significant computational resources for solution of the equations of motion. Much of the model, however, is linear where the nonlinearity results from discrete local elements connecting different components together. Using a component mode synthesis approach, a nonlinear model can be developed by interconnecting these linear components with highly nonlinear connection elements. The approach presented in this paper, the Modal Modification Response Technique (MMRT), is a very efficient technique that has been created to address this specific class of nonlinear problem. By utilizing a Structural Dynamics Modification (SDM) approach in conjunction with mode superposition, a significantly smaller set of matrices are required for use in the direct integration of the equations of motion. The approach will be compared to traditional analytical approaches to make evident the usefulness of the technique for a variety of test cases.

No-cost manual method for preparation of tissue microarrays having high quality comparable to semiautomated methods.

PubMed

Foda, Abd Al-Rahman Mohammad

2013-05-01

Manual tissue microarray (TMA) construction had been introduced to avoid the high cost of automated and semiautomated techniques. The cheapest and simplest technique for constructing manual TMA was that of using mechanical pencil tips. This study was carried out to modify this method, aiming to raise its quality to reach that of expensive ones. Some modifications were introduced to Shebl's technique. Two conventional mechanical pencil tips of different diameters were used to construct the recipient blocks. A source of mild heat was used, and blocks were incubated at 38°C overnight. With our modifications, 3 high-density TMA blocks were constructed. We successfully performed immunostaining without substantial tissue loss. Our modifications increased the number of cores per block and improved the stability of the cores within the paraffin block. This new, modified technique is a good alternative for expensive machines in many laboratories.

40 CFR 52.1225 - Review of new sources and modifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Minnesota § 52.1225 Review of new sources and modifications. (a) Part D—Approval. The State of Minnesota has satisfied the... nonattainment areas. (b)-(d) [Reserved] (e) The State of Minnesota has committed to conform to the Stack Height...

40 CFR 52.1225 - Review of new sources and modifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Minnesota § 52.1225 Review of new sources and modifications. (a) Part D—Approval. The State of Minnesota has satisfied the... nonattainment areas. (b)-(d) [Reserved] (e) The State of Minnesota has committed to conform to the Stack Height...

40 CFR 52.1225 - Review of new sources and modifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Minnesota § 52.1225 Review of new sources and modifications. (a) Part D—Approval. The State of Minnesota has satisfied the... nonattainment areas. (b)-(d) [Reserved] (e) The State of Minnesota has committed to conform to the Stack Height...

40 CFR 52.1225 - Review of new sources and modifications.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Minnesota § 52.1225 Review of new sources and modifications. (a) Part D—Approval. The State of Minnesota has satisfied the... nonattainment areas. (b)-(d) [Reserved] (e) The State of Minnesota has committed to conform to the Stack Height...

40 CFR 52.1225 - Review of new sources and modifications.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Minnesota § 52.1225 Review of new sources and modifications. (a) Part D—Approval. The State of Minnesota has satisfied the... nonattainment areas. (b)-(d) [Reserved] (e) The State of Minnesota has committed to conform to the Stack Height...

Physician Behavior Modification Using Claims Data: Tetracycline for Upper Respiratory Infection

PubMed Central

McConnell, Thomas S.; Cushing, Alice H.; Bankhurst, Arthur D.; Healy, James L.; McIlvenna, Patricia A.; Skipper, Betty J.

1982-01-01

Professional Standards Review Organization claims data were used in defining, planning, implementing and evaluating an approach to an ambulatory medical care problem utilizing educational intervention. Modification of physicians' tetracycline prescribing behavior was achieved in an actual practice setting by personal visits from peer physicians. PMID:6891147

Proposal of Modification Strategy of NC Program in the Virtual Manufacturing Environment

NASA Astrophysics Data System (ADS)

Narita, Hirohisa; Chen, Lian-Yi; Fujimoto, Hideo; Shirase, Keiichi; Arai, Eiji

Virtual manufacturing will be a key technology in process planning, because there are no evaluation tools for cutting conditions. Therefore, virtual machining simulator (VMSim), which can predict end milling processes, has been developed. The modification strategy of NC program using VMSim is proposed in this paper.

20 CFR 668.750 - Under what circumstances can we or the INA grantee modify the terms of the grantee's plan(s)?

Code of Federal Regulations, 2010 CFR

2010-04-01

... the INA grantee's plan to add funds or, if required by Congressional action, to reduce the amount of funds available for expenditure. (b) The INA grantee may request approval to modify its plan to add... event that further clarification or modification is required, we may extend the thirty (30) day time...

20 CFR 668.750 - Under what circumstances can we or the INA grantee modify the terms of the grantee's plan(s)?

Code of Federal Regulations, 2011 CFR

2011-04-01

... the INA grantee's plan to add funds or, if required by Congressional action, to reduce the amount of funds available for expenditure. (b) The INA grantee may request approval to modify its plan to add... event that further clarification or modification is required, we may extend the thirty (30) day time...

Specific Sensory Techniques and Sensory Environmental Modifications for Children and Youth With Sensory Integration Difficulties: A Systematic Review.

PubMed

Bodison, Stefanie C; Parham, L Diane

This systematic review examined the effectiveness of specific sensory techniques and sensory environmental modifications to improve participation of children with sensory integration (SI) difficulties. Abstracts of 11,436 articles published between January 2007 and May 2015 were examined. Studies were included if designs reflected high levels of evidence, participants demonstrated SI difficulties, and outcome measures addressed function or participation. Eight studies met inclusion criteria. Seven studies evaluated effects of specific sensory techniques for children with autism spectrum disorder (ASD) or attention deficit hyperactivity disorder: Qigong massage, weighted vests, slow swinging, and incorporation of multisensory activities into preschool routines. One study of sensory environmental modifications examined adaptations to a dental clinic for children with ASD. Strong evidence supported Qigong massage, moderate evidence supported sensory modifications to the dental care environment, and limited evidence supported weighted vests. The evidence is insufficient to draw conclusions regarding slow linear swinging and incorporation of multisensory activities into preschool settings. Copyright © 2018 by the American Occupational Therapy Association, Inc.

Local dynamic range compensation for scanning electron microscope imaging system.

PubMed

Sim, K S; Huang, Y H

2015-01-01

This is the extended project by introducing the modified dynamic range histogram modification (MDRHM) and is presented in this paper. This technique is used to enhance the scanning electron microscope (SEM) imaging system. By comparing with the conventional histogram modification compensators, this technique utilizes histogram profiling by extending the dynamic range of each tile of an image to the limit of 0-255 range while retains its histogram shape. The proposed technique yields better image compensation compared to conventional methods. © Wiley Periodicals, Inc.

Public perceptions of hurricane modification.

PubMed

Klima, Kelly; Bruine de Bruin, Wändi; Morgan, M Granger; Grossmann, Iris

2012-07-01

If hurricane modification were to become a feasible strategy for potentially reducing hurricane damages, it would likely generate public discourse about whether to support its implementation. To facilitate an informed and constructive discourse, policymakers need to understand how people perceive hurricane modification. Here, we examine Florida residents' perceptions of hurricane modification techniques that aim to alter path and wind speed. Following the mental models approach, we conducted a survey study about public perceptions of hurricane modification that was guided by formative interviews on the topic. We report a set of four primary findings. First, hurricane modification was perceived as a relatively ineffective strategy for damage reduction, compared to other strategies for damage reduction. Second, hurricane modification was expected to lead to changes in projected hurricane path, but not necessarily to the successful reduction of projected hurricane strength. Third, more anger was evoked when a hurricane was described as having changed from the initially forecasted path or strength after an attempted modification. Fourth, unlike what we expected, participants who more strongly agreed with statements that recognized the uncertainty inherent in forecasts reported more rather than less anger at scientists across hurricane modification scenarios. If the efficacy of intensity-reduction techniques can be increased, people may be willing to support hurricane modification. However, such an effort would need to be combined with open and honest communications to members of the general public. © 2011 Society for Risk Analysis.

Recruiting and enrolling pregnant adolescents for research.

PubMed

Kaiser, Margaret M; Hays, Bevely J

2006-01-01

Difficulty obtaining a sample is not justification for failure to study a hard-to-enroll population, particularly a vulnerable population such as pregnant adolescents. Recruitment of a representative, adequate sample of pregnant adolescents for a recent instrument development study provided multiple challenges. Although carefully developed, the sampling plan required several modifications to achieve the sample (n=145). Those challenges and the ensuing modifications to the sampling plan are discussed in relation to (a) access/institutional concerns, (b) the human subject's protection considerations, and (c) developmental/personal concerns of the pregnant adolescents. Recommendations for sampling strategies for future research are offered.

A Robust and Affordable Table Indexing Approach for Multi-isocenter Dosimetrically Matched Fields.

PubMed

Yu, Amy; Fahimian, Benjamin; Million, Lynn; Hsu, Annie

2017-05-23

Purpose  Radiotherapy treatment planning of extended volume typically necessitates the utilization of multiple field isocenters and abutting dosimetrically matched fields in order to enable coverage beyond the field size limits. A common example includes total lymphoid irradiation (TLI) treatments, which are conventionally planned using dosimetric matching of the mantle, para-aortic/spleen, and pelvic fields. Due to the large irradiated volume and system limitations, such as field size and couch extension, a combination of couch shifts and sliding of patients are necessary to be correctly executed for accurate delivery of the plan. However, shifting of patients presents a substantial safety issue and has been shown to be prone to errors ranging from minor deviations to geometrical misses warranting a medical event. To address this complex setup and mitigate the safety issues relating to delivery, a practical technique for couch indexing of TLI treatments has been developed and evaluated through a retrospective analysis of couch position. Methods The indexing technique is based on the modification of the commonly available slide board to enable indexing of the patient position. Modifications include notching to enable coupling with indexing bars, and the addition of a headrest used to fixate the head of the patient relative to the slide board. For the clinical setup, a Varian Exact Couch TM (Varian Medical Systems, Inc, Palo Alto, CA) was utilized. Two groups of patients were treated: 20 patients with table indexing and 10 patients without. The standard deviations (SDs) of the couch positions in longitudinal, lateral, and vertical directions through the entire treatment cycle for each patient were calculated and differences in both groups were analyzed with Student's t-test. Results The longitudinal direction showed the largest improvement. In the non-indexed group, the positioning SD ranged from 2.0 to 7.9 cm. With the indexing device, the positioning SD was reduced to a range of 0.4 to 1.3 cm (p < 0.05 with 95% confidence level). The lateral positioning was slightly improved (p < 0.05 with 95% confidence level), while no improvement was observed in the vertical direction. Conclusions The conventional matched field TLI treatment is error-prone to geometrical setup error. The feasibility of full indexing TLI treatments was validated and shown to result in a significant reduction of positioning and shifting errors.

Laser hardening techniques on steam turbine blade and application

NASA Astrophysics Data System (ADS)

Yao, Jianhua; Zhang, Qunli; Kong, Fanzhi; Ding, Qingming

Different laser surface hardening techniques, such as laser alloying and laser solution strengthening were adopted to perform modification treatment on the local region of inset edge for 2Cr13 and 17-4PH steam turbine blades to prolong the life of the blades. The microstructures, microhardness and anti-cavitation properties were investigated on the blades after laser treatment. The hardening mechanism and technique adaptability were researched. Large scale installation practices confirmed that the laser surface modification techniques are safe and reliable, which can improve the properties of blades greatly with advantages of high automation, high quality, little distortion and simple procedure.

Training Secondary School Teachers in Instructional Language Modification Techniques to Support Adolescents with Language Impairment: A Randomized Controlled Trial

ERIC Educational Resources Information Center

Starling, Julia; Munro, Natalie; Togher, Leanne; Arciuli, Joanne

2012-01-01

Purpose: This study evaluated the efficacy of a collaborative intervention where a speech-language pathologist (SLP) trained mainstream secondary school teachers to make modifications to their oral and written instructional language. The trained teachers' uptake of techniques in their whole-class teaching practices and the impact this had on the…

Abusing the Unprotected: A Study of the Misuse of Aversive Behavior Modification Techniques and Weaknesses in the Regulatory Structure.

ERIC Educational Resources Information Center

New York State Commission on Quality of Care for the Mentally Disabled, Albany.

This report examines issues concerned with the use of aversive behavior modification techniques in actual treatment practices at one intermediate care facility for the mentally retarded. The review of these practices reveals how, once the philosophy of using aversives takes hold at a program (to deal with seemingly intractable behaviors), its…

A Modification of Copeyon's Drilling Technique for Making Artificial Red-Cockaded Woodpecker Cavities

Treesearch

William E. Taylor; Robert G. Hooper

1991-01-01

A modification to Copeyon's drilling technique for making highly effective artificial cavities for red-cockaded wookpeckers is described.The changes virtually eliminate the possibility of making a mistake in constructing cavities and reduces the learning time to less than 2 weeks.The basic change is the use of a 3-inch access hole that allows the relative position...

Modifications Of Hydrostatic-Bearing Computer Program

NASA Technical Reports Server (NTRS)

Hibbs, Robert I., Jr.; Beatty, Robert F.

1991-01-01

Several modifications made to enhance utility of HBEAR, computer program for analysis and design of hydrostatic bearings. Modifications make program applicable to more realistic cases and reduce time and effort necessary to arrive at a suitable design. Uses search technique to iterate on size of orifice to obtain required pressure ratio.

20 CFR 669.540 - Under what circumstances are the terms of the grantee's plan modified by the grantee or the...

Code of Federal Regulations, 2012 CFR

2012-04-01

... Department? (a) Plans must be modified to reflect the funding level for the second year of the designation cycle. We will provide instructions for when to submit modifications for second year funding, which will... its service delivery plan to reflect the effect of the waiver. ...

Gonioscopy-assisted Transluminal Trabeculotomy (GATT): Thermal Suture Modification With a Dye-stained Rounded Tip.

PubMed

Grover, Davinder S; Fellman, Ronald L

2016-06-01

To describe a novel technique for thermally marking the tip of a suture, in preparation for a gonioscopy-assisted transluminal trabeculotomy. One patient was used as an example for this technique. Technique report. The authors introduce a modification of a novel surgical procedure (GATT) in which a suture is marked and thermally blunted allowing a proper visualization while performing an ab interno, minimally invasive, circumferential 360-degree suture trabeculotomy. The authors have previously reported on the GATT surgery with the use of an illuminated microcatheter, which allowed for visualization of the tip of the catheter as it circumnavigated Schlemm canal. This modification allows for similar visualization of the tip of the suture, however, is much more cost-effective while still maintaining similar safety.

An Adaption Tool Kit for Teaching Music

ERIC Educational Resources Information Center

McDowell, Carol

2010-01-01

Music-education majors often struggle when making classroom and curricular modifications for their lesson plans during their university coursework. This article offers behavioral, curricular, environmental, motivational, organizational, and presentational strategies for planning instruction for various disabilities in the music classroom.…

Surface modification of medical implant materials with hydrophilic polymers for enhanced biocompatibility and delivery of therapeutic agents

NASA Astrophysics Data System (ADS)

Urbaniak, Daniel J.

2004-11-01

In the research reported here, the surface modification of medical grade poly(dimethyl siloxane), polyetherurethane, and stainless steel through gamma-radiation grafting of hydrophilic polymers was investigated. Emphasis was placed on developing improved and simplified surface modification methods that produce more stable and more bioacceptible hydrophilic graft surfaces. As a result of this research, new surface modification techniques were developed that yield significantly improved surface stability unachievable using previous surface modification techniques. The surface modification of poly(dimethyl siloxane) with hydrophilic polymers was carried out using gamma radiation initiated graft polymerization. The addition of alkali metal hydroxides afforded a unique way to enhance the grafting of N-vinyl-2 pyrrolidone, dimethylacryamide, 2-methacryloyloxyethyl phosphoryl choline, N,N-dimethyl-N-(methacryloyloxyethyl)-N-(3-sulfopropyl)-ammonium-betaine, N,N-dimethyl-N-(methacrylamidopropyl)-N-(3-sulfopropyl)-ammonium-betaine, and copolymers thereof to silicones. Ethanolamine was found to further enhance the grafting of some hydrophilic polymers to silicone. The resulting hydrophilic surface grafts were resistant to hydrophobic surface rearrangement. This process overcomes previous problems inherent in silicone surface modification. The technique was also found to moderately enhance the grafting of hydrophilic monomers to polyetherurethane and to 316-L stainless steel. The surface modification of 316-L stainless steel was further enhanced by treating the substrates with a chromium III methacrylate bonding agent prior to irradiation. The coatings were evaluated for their potential use as depots for delivering therapeutic agents. The release of ofloxacin from surface-modified poly(dimethyl siloxane) and dexamethasone from surface-modified 316-L stainless steel was evaluated by in-vitro experiments. Therapeutic levels of drugs were released from surface-modified specimens via a burst effect. Improved surface characterization methods were another aspect of this research. New nanomechanical testing techniques were developed and used to evaluate the viscoelastic surface mechanical properties of low modulus surface-modified specimens. Dynamic nanoindentation characterization techniques were designed to measure the storage modulus and loss modulus of compliant viscoelastic substrate surfaces. The results of these experiments were compared with modulus data obtained by conventional dynamic mechanical spectroscopy. Nanoscratch testing methods were also developed that qualitatively compared the abrasion resistance of surface-modified substrates. (Abstract shortened by UMI.)

A Novel Surgical Technique for Ahmed Valves in Refractory Glaucoma With Silicone Oil Endotamponade.

PubMed

Davo-Cabrera, Juan Maria; Lanzagorta-Aresti, Aitor; Alcocer Yuste, Pablo

2017-10-01

The purpose of the study is to describe a novel technique to implant Ahmed valves in patients with refractory glaucoma because of silicone oil (SO) endotamponade PATIENTS:: Three patients with glaucoma without SO removal were used as an example for this technique. Technique report. We introduce a standard technique modification for Ahmed valves in patients with SO. This modification consists on locating the Ahmed valve more tangential to the limbus curvature instead of the usual perpendicular position and inserting the tube in the posterior chamber. The tube can be longer and run parallel to pupil. This technique allows use superotemporal quadrant (fewer complications), avoid corneal touch and decrease SO loss through the tube to subconjunctival space.

29 CFR 1902.12 - Opportunity for modifications and clarifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false Opportunity for modifications and clarifications. 1902.12 Section 1902.12 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR STATE PLANS FOR THE DEVELOPMENT AND ENFORCEMENT OF STATE STANDARDS Procedures for Submission, Approval and Rejection of...

40 CFR 122.63 - Minor modifications of permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Minor modifications of permits. 122.63..., coverage, and liability between the current and new permittees has been submitted to the Director. (e)(1...) Incorporate changes to the terms of a CAFO's nutrient management plan that have been revised in accordance...

Improvements In Ball-Screw Linear Actuators

NASA Technical Reports Server (NTRS)

Iskenderian, Theodore; Joffe, Benjamin; Summers, Robert

1996-01-01

Report describes modifications of design of type of ball-screw linear actuator driven by dc motor, with linear-displacement feedback via linear variable-differential transformer (LVDT). Actuators used to position spacecraft engines to direct thrust. Modifications directed toward ensuring reliable and predictable operation during planned 12-year cruise and interval of hard use at end of cruise.

75 FR 77919 - Carolina Power & Light Company Shearon Harris Nuclear Power Plant, Unit 1; Environmental...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-14

... involves important physical modifications to the HNP, Unit 1 security system. There are several issues... in which some important security modifications are planned. A direct outside access route to the... implementation deadline, the licensee currently maintains a security system acceptable to the NRC and that will...

Influence of (11)C-choline PET/CT on radiotherapy planning in prostate cancer.

PubMed

López, Escarlata; Lazo, Antonio; Gutiérrez, Antonio; Arregui, Gregorio; Núñez, Isabel; Sacchetti, Antonio

2015-01-01

To evaluate the influence of (11)C-choline PET/CT on radiotherapy planning in prostate cancer patients. Precise information on the extension of prostate cancer is crucial for the choice of an appropriate therapeutic strategy. (11)C-choline positron emission tomography ((11)C-choline PET/CT) has two roles in radiation oncology (RT): (1) patient selection for treatment and (2) target volume selection and delineation. In conjunction with high-accuracy techniques, it might offer an opportunity of dose escalation and better tumour control while sparing healthy tissues. We carried out a retrospective study in order to analyse RT planning modification based on (11)C-choline PET/CT in 16 prostate cancer patients. Patients were treated with hypofractionated step-and-shoot Intensity Modulated Radiotherapy (IMRT), or Volumetric Modulated Arc Therapy (VMAT), and a daily cone-beam CT for Image Guided Radiation Therapy (IGRT). All patients underwent a (11)C-choline-PET/CT scan prior to radiotherapy. In 37.5% of cases, a re-delineation and new dose prescription occurred. Data show good preliminary clinical results in terms of biochemical control and toxicity. No gastrointestinal (GI)/genitourinary (GU) grade III toxicities were observed after a median follow-up of 9.5 months. In our experience, concerning the treatment of prostate cancer (PCa), (11)C-choline PET/CT may be helpful in radiotherapy planning, either for dose escalation or exclusion of selected sites.

IGOS improvements for Seasat

NASA Technical Reports Server (NTRS)

Warmke, J. M.

1979-01-01

Modifications to Battelle's Interactive Graphics Orbit Selection (IGOS) computer program to assist in the planning and evaluation of the Seasat-A Scatterometer System (SASS) flight program were studied. To meet the planning needs of the LaRC Seasat-A Scatterometer team, the following features/modifications were implemented in IGOS: (1) display and specification of time increments in orbital passes represented by the cross-hatching of ground swaths; (2) addition of pass number annotations on the horizontal axis of the STPLNG and STPTOD plots; (3) modification of the sensor model to include more than two swaths associated with a single sensor to approximate the SASS cell pattern; (4) inclusion of down range and cross-track swath geometry to display the characteristic skewed SASS pattern; (5) addition of a swath schedule to allow the display of the SASS mode changes and to calibrate gaps; and (6) development of a set of commands to generate the detailed swath data from sensor characteristics and orbit/earth motion.

Proposed Modification to Sebade Farms Nutrient Management Plan

EPA Pesticide Factsheets

Sebade Farms is a concentrated animal feeding operation (CAFO) located on the Winnebago Reservation in Nebraska that confines a total of 6,500 head of cattle. The terms of the Nutrient Management Plan (NMP) are incorporated by reference into the facility’s

48 CFR 243.204-70-7 - Plans and reports.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SYSTEM, DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT CONTRACT MODIFICATIONS Change Orders 243.204-70-7 Plans and reports. To provide for enhanced management and oversight of unpriced change orders, departments and agencies shall— (a) Include in the Consolidated Undefinitized Contract Action (UCA) Management...

A 3D isodose manipulation tool for interactive dose shaping

NASA Astrophysics Data System (ADS)

Kamerling, C. P.; Ziegenhein, P.; Heinrich, H.; Oelfke, U.

2014-03-01

The interactive dose shaping (IDS) planning paradigm aims to perform interactive local dose adaptations of an IMRT plan without compromising already established valuable dose features in real-time. In this work we introduce an interactive 3D isodose manipulation tool which enables local modifications of a dose distribution intuitively by direct manipulation of an isodose surface. We developed an in-house IMRT TPS framework employing an IDS engine as well as a 3D GUI for dose manipulation and visualization. In our software an initial dose distribution can be interactively modified through an isodose surface manipulation tool by intuitively clicking on an isodose surface. To guide the user interaction, the position of the modification is indicated by a sphere while the mouse cursor hovers the isodose surface. The sphere's radius controls the locality of the modification. The tool induces a dose modification as a direct change of dose in one or more voxels, which is incrementally obtained by fluence adjustments. A subsequent recovery step identifies voxels with violated dose features and aims to recover their original dose. We showed a proof of concept study for the proposed tool by adapting the dose distribution of a prostate case (9 beams, coplanar). Single dose modifications take less than 2 seconds on an actual desktop PC.

Intraluminal pressure response in Baerveldt tube shunts: a comparison of modification techniques.

PubMed

Gilbert, David D; Bond, Brent

2007-01-01

To design an apparatus for in vitro quantification of effects of modifications to nonvalved tube shunts, and to compare the effects of these modifications done to prevent early postoperative hypotony. A testing apparatus was designed and constructed to measure intraluminal pressure (ILP) during constant infusion of balanced salt solution at 2 microL/min through Baerveldt tube shunts mounted on cadaver eyes. Three different modifications were performed and 3 shunts were used for each modification. The modifications were partial tube occlusion with a 3-0 Supramid suture, tube perforation with a 27-gauge needle on an occluded tube, and a 1.2 mm longitudinal venting slit on an occluded tube. The final steady state ILP for the 3-0 Supramid partially occluded tube ranged between 1.6 and 2.8 mm Hg over 3 trials with an average final steady state ILP of 2.0 mm Hg. The 27-gauge needle perforation produced ILPs of 4.6 to 8.2 mm Hg over 3 trials with an average final steady state pressure of 5.9 mm Hg. The 1.2 mm longitudinal venting slit produced an ILP range of 12.6 to 17.3 mm Hg over 3 trials with an average final steady state ILP of 14.8 mm Hg. The differences in final steady state ILP between the 3 modification techniques were statistically significant (P=0.00036). The 3-0 Supramid occlusion and the 27-gauge perforation techniques produced hypotony, whereas the 1.2 mm longitudinal venting slit produced acceptable pressures in vitro.

Selected photographic techniques, a compilation

NASA Technical Reports Server (NTRS)

1971-01-01

A selection has been made of methods, devices, and techniques developed in the field of photography during implementation of space and nuclear research projects. These items include many adaptations, variations, and modifications to standard hardware and practice, and should prove interesting to both amateur and professional photographers and photographic technicians. This compilation is divided into two sections. The first section presents techniques and devices that have been found useful in making photolab work simpler, more productive, and higher in quality. Section two deals with modifications to and special applications for existing photographic equipment.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coburn, Natalie, E-mail: natalie.coburn@swahs.health.nsw.gov.au; Beldham-Collins, Rachael; Radiation Oncology Network, Westmead Cancer Care Centre, University of Sydney, Sydney, New South Wales

Protocols commonly implemented in radiotherapy work areas may be classified as being either rigid (class solution) or flexible. Because formal evaluation of these protocol types has not occurred within the literature, we evaluated the efficiency of a rigid compared with flexible prostate planning protocol by assessing a series of completed 3D conformal prostate plans. Twenty prostate cancer patients with an average age of 70 years (range, 52-77) and sizes comprising 8 small, 10 medium, and 2 large were planned on the Phillips Pinnacle treatment planning system 6 times by radiation therapists with <2 years, 2-5 years, and >5 years ofmore » experience using a rigid and flexible protocol. Plans were critiqued using critical organ doses, confirmation numbers, and conformity index. Plans were then classified as being acceptable or not. Plans produced with the flexible protocol were 53% less likely to require modification (OR 0.47, 95% CI: 0.26, 0.84, p = 0.01). Planners with >5 years of experience were 78% more likely to produce plans requiring modification (OR 1.78, 95% CI: 1.12, 2.83, P = 0.02). Plans according to the flexible protocol took longer (112 min) compared with the time taken using a rigid protocol (68 min) (p < 0.001). The results suggest that further studies are needed; however, we propose that all radiation therapy planners should start with the same limitations, and if an acceptable plan is not reached, then flexibility should be given to improve the plan to meet the desired results.« less

20 CFR 668.750 - Under what circumstances can we or the INA grantee modify the terms of the grantee's plan(s)?

Code of Federal Regulations, 2012 CFR

2012-04-01

... modify the INA grantee's plan to add funds or, if required by Congressional action, to reduce the amount... add, expand, delete, or diminish any service allowable under the regulations in this part. The INA... event that further clarification or modification is required, we may extend the thirty (30) day time...

20 CFR 668.750 - Under what circumstances can we or the INA grantee modify the terms of the grantee's plan(s)?

Code of Federal Regulations, 2014 CFR

2014-04-01

... modify the INA grantee's plan to add funds or, if required by Congressional action, to reduce the amount... add, expand, delete, or diminish any service allowable under the regulations in this part. The INA... event that further clarification or modification is required, we may extend the thirty (30) day time...

20 CFR 668.750 - Under what circumstances can we or the INA grantee modify the terms of the grantee's plan(s)?

Code of Federal Regulations, 2013 CFR

2013-04-01

... modify the INA grantee's plan to add funds or, if required by Congressional action, to reduce the amount... add, expand, delete, or diminish any service allowable under the regulations in this part. The INA... event that further clarification or modification is required, we may extend the thirty (30) day time...

137. ARAII Building ARA602 floor plan as it appeared in ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

137. ARA-II Building ARA-602 floor plan as it appeared in 1980 when electrical modifications were being made. Shows partial layout of floor plan. EG&G Idaho, Inc. 1570-ARA-II-602-E-3. Date: April 1980. Ineel index code no. 070--0602-10-220-159761. - Idaho National Engineering Laboratory, Army Reactors Experimental Area, Scoville, Butte County, ID

West Java Snack Mapping based on Snack Types, Main Ingredients, and Processing Techniques

NASA Astrophysics Data System (ADS)

Nurani, A. S.; Subekti, S.; Ana

2016-04-01

The research was motivated by lack of literature on archipelago snack especially from West Java. It aims to explore the snack types, the processing techniques, and the main ingredients by planning a learning material on archipelago cake especially from West Java. The research methods used are descriptive observations and interviews. The samples were randomly chosen from all regions in West Java. The findings show the identification of traditional snack from West java including: 1. snack types which are similar in all regions as research sample namely: opak, rangginang, nagasari, aliagrem, cuhcur, keripik, semprong, wajit, dodol, kecimpring, combro, tape ketan, and surabi. The typical snack types involve burayot (Garut), simping kaum (Purwakarta), surabi hejo (Karawang), papais cisaat (Subang), Papais moyong, opak bakar (Kuningan), opak oded, ranggesing (Sumedang), gapit, tapel (Cirebon), gulampo, kue aci (Tasikmalaya), wajit cililin, gurilem (West Bandung), and borondong (Bandung District); 2. various processing techniques namely: steaming, boiling, frying, caramelizing, baking, grilling, roaster, sugaring; 3. various main ingredients namely rice, local glutinous rice, rice flour, glutinous rice flour, starch, wheat flour, hunkue flour, cassava, sweet potato, banana, nuts, and corn; 4. snack classification in West Java namely (1) traditional snack, (2) creation-snack, (3) modification-snack, (4) outside influence-snack.

Titration in the treatment of the more troubled patient.

PubMed

Winer, J A; Ornstein, E D

2001-01-01

This article defines and discusses a modification of technique recommended by the authors in the psychoanalytic treatment of more troubled patients--a modification they call titration. Titration is defined as a conscious decision by the analyst to increase or decrease assistance (or gratification) gradually, in order to facilitate the analytic process. The authors emphasize the complexity of decisions in treatment by focusing on the decision-making processes that titration requires. Guidelines and a case vignette are presented. The authors conclude by considering some of the politics involved in the introduction of technique modifications, the salience of the titration concept, and directions for further exploration.

20 CFR 631.19 - Appeals.

Code of Federal Regulations, 2010 CFR

2010-04-01

... training plans or modifications) shall apply to final disapproval of substate plans under § 631.50(f) of...' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF LABOR PROGRAMS UNDER TITLE III OF THE JOB TRAINING PARTNERSHIP ACT Additional Title III Administrative Standards and Procedures § 631.19 Appeals...

77 FR 8114 - Plan for Retrospective Analysis of Existing Rules

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-14

... Existing Rules without significant changes from the version that was preliminarily proposed. Accordingly... modification or elimination of existing regulations. Once an appropriate rule change has been identified, the... INTERNATIONAL TRADE COMMISSION 19 CFR Chapter II Plan for Retrospective Analysis of Existing Rules...

Elementary Physical Education Weekly Lesson Plan. Grades 1, 2.

ERIC Educational Resources Information Center

Anchorage Borough School District, AK.

This curriculum guide provides weekly lesson plans for the physical education of first and second grade students and lists specific activities along with organization and teaching procedures for each. Warm-up activities, safety procedures, modifications and athletic equipment are described for each activity. (CJ)

24 CFR 598.415 - Reporting.

Code of Federal Regulations, 2011 CFR

2011-04-01

... been taken in accordance with the strategic plan and provide notice of updates and modifications to the strategic plan. In addition to these reports, such other information relating to designated Empowerment... required to submit in accordance with this part. (Approved by the Office of Management and Budget under...

Orbiter Auxiliary Power Unit Flight Support Plan

NASA Technical Reports Server (NTRS)

Guirl, Robert; Munroe, James; Scott, Walter

1990-01-01

This paper discussed the development of an integrated Orbiter Auxiliary Power Unit (APU) and Improved APU (IAPU) Flight Suuport Plan. The plan identifies hardware requirements for continued support of flight activities for the Space Shuttle Orbiter fleet. Each Orbiter vehicle has three APUs that provide power to the hydraulic system for flight control surface actuation, engine gimbaling, landing gear deployment, braking, and steering. The APUs contain hardware that has been found over the course of development and flight history to have operating time and on-vehicle exposure time limits. These APUs will be replaced by IAPUs with enhanced operating lives on a vehicle-by-vehicle basis during scheduled Orbiter modification periods. This Flight Support Plan is used by program management, engineering, logistics, contracts, and procurement groups to establish optimum use of available hardware and replacement quantities and delivery requirements for APUs until vehicle modifications and incorporation of IAPUs. Changes to the flight manifest and program delays are evaluated relative to their impact on hardware availability.

Aircraft modifications: Assessing the current state of Air Force aircraft modifications and the implications for future military capability

NASA Astrophysics Data System (ADS)

Hill, Owen Jacob

How prepared is the U.S. Air Force to modify its aircraft fleet in upcoming years? Aircraft modernization is a complex interaction of new and legacy aircraft, organizational structure, and planning policy. This research will take one component of modernization: aircraft modification, and apply a new method of analysis in order to help formulate policy to promote modernization. Departing from previous small-sample studies dependent upon weight as a chief explanatory variable, this dissertation incorporates a comprehensive dataset that was constructed for this research of all aircraft modifications from 1996 through 2005. With over 700 modification programs, this dataset is used to examine changes to the current modification policy using policy-response regression models. These changes include separating a codependent procurement and installation schedule, reducing the documentation requirements for safety modifications, and budgeting for aging aircraft modifications. The research then concludes with predictive models for the F-15 and F-16 along with their replacements: the F-22 and F-35 Joint Strike Fighter.

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA, John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA, John F. Kennedy Space Center, Florida. Drawing 79K05424, Seelye Stevenson Value & Knecht, March, 1975. SITE WORK, GENERAL AREA PLAN. Sheet 8 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

The Globalization of Higher Education--Be Responsible and Survive the Changes

ERIC Educational Resources Information Center

Havlicek, Jaroslav; Pelikan, Martin

2013-01-01

The ongoing social changes taking place on a global scale have made universities respond to these new challenges by offering new study programmes, implementing modifications of study plans, taking up new research focus as well as by broadening the offer of adult education. These changes necessarily require modifications in terms of the structure…

Photography equipment and techniques. A survey of NASA developments

NASA Technical Reports Server (NTRS)

Derr, A. J.

1972-01-01

The Apollo program has been the most complex exploration ever attempted by man, requiring extensive research, development, and engineering in most of the sciences before the leap through space could begin. Photography has been used at each step of the way to document the efforts and activities, isolate mistakes, reveal new phenomena, and to record much that cannot be seen by the human eye. At the same time, the capabilities of photography were extended because of the need of meeting space requirements. The results of this work have been applied to community planning and ecology, for example, as well as to space and engineering. Special uses of standard equipment, modifications and new designs, as well as film combinations that indicate actual or potential ecological problems are described.

Albumin modification and fragmentation in renal disease.

PubMed

Donadio, Carlo; Tognotti, Danika; Donadio, Elena

2012-02-18

Albumin is the most important antioxidant substance in plasma and performs many physiological functions. Furthermore, albumin is the major carrier of endogenous molecules and exogenous ligands. This paper reviews the importance of post-translational modifications of albumin and fragments thereof in patients with renal disease. First, current views and controversies on renal handling of proteins, mainly albumin, will be discussed. Post-translational modifications, namely the fragmentation of albumin found with proteomic techniques in nephrotic patients, diabetics, and ESRD patients will be presented and discussed. It is reasonable to hypothesize that proteolytic fragmentation of serum albumin is due to a higher susceptibility to proteases, induced by oxidative stress. The clinical relevance of the fragmentation of albumin has not yet been established. These modifications could affect some physiological functions of albumin and have a patho-physiological role in uremic syndrome. Proteomic analysis of serum allows the identification of over-expressed proteins and can detect post-translational modifications of serum proteins, hitherto hidden, using standard laboratory techniques. Copyright © 2011 Elsevier B.V. All rights reserved.

Surface Characterization Techniques: An Overview

NASA Technical Reports Server (NTRS)

Miyoshi, Kazuhisa

2002-01-01

To understand the benefits that surface modifications provide, and ultimately to devise better ones, it is necessary to study the physical, mechanical, and chemical changes they cause. This chapter surveys classical and leading-edge developments in surface structure and property characterization methodologies. The primary emphases are on the use of these techniques as they relate to surface modifications, thin films and coatings, and tribological engineering surfaces and on the implications rather than the instrumentation.

Evaluation of footprint contact area and pressure using a triple-row modification of the suture-bridge technique for rotator cuff repair.

PubMed

Ostrander, Roger V; McKinney, Bart I

2012-10-01

Studies suggest that arthroscopic repair techniques may have high recurrence rates for larger rotator cuff tears. A more anatomic repair may improve the success rate when performing arthroscopic rotator cuff repair. We hypothesized that a triple-row modification of the suture-bridge technique for rotator cuff repair would result in significantly more footprint contact area and pressure between the rotator cuff and the humeral tuberosity. Eighteen ovine infraspinatus tendons were repaired using 1 of 3 simulated arthroscopic techniques: a double-row repair, the suture-bridge technique, and a triple-row repair. The triple-row repair technique is a modification of the suture-bridge technique that uses an additional reducing anchor between the medial and lateral rows. Six samples were tested per group. Pressure-indicating film was used to measure the footprint contact area and pressure after each repair. The triple-row repair resulted in significantly more rotator cuff footprint contact area and contact pressure compared with the double-row technique and the standard suture-bridge technique. No statistical difference in contact area or contact pressure was found between the double-row technique and the suture-bridge technique. The triple-row technique for rotator cuff repair results in significantly more footprint contact area and contact pressure compared with the double-row and standard suture-bridge techniques. This more anatomic repair may improve the healing rate when performing arthroscopic rotator cuff repair. Copyright © 2012 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Mosby, Inc. All rights reserved.

What about OMT and nutrition for managing the irritable bowel syndrome? An overview and treatment plan.

PubMed

Collebrusco, Luca; Lombardini, Rita

2014-01-01

A chronic continuous or intermittent gastrointestinal tract dysfunction, the irritable bowel syndrome (IBS), appears to be due to dysregulation of brain-gut-microbiota communication. Furthermore, the "microbiota" greatly impacts the bi-directional brain-gut axis communication. This article describes IBS in relation to similar diseases, presents the background to osteopathy, and proposes osteopathic manipulative treatment (OMT) to manage IBS. In IBS, OMT focuses on the nervous and circulatory systems, spine, viscera, and thoracic and pelvic diaphragms in order to restore homeostatic balance, normalize autonomic activity in the intestine, promote lymphatic flow, and address somatic dysfunction. Lymphatic and venous congestion are treated by the lymphatic pump techniques and stimulation of Chapman׳s reflex points. A simple treatment plan designed to lessen chronic pain and inflammation in IBS is presented based on current evidence-based literature. Since food itself, food allergies, and intolerance could contribute to symptom onset or even cause IBS, this article also provides dietary modifications to consider for patients. Copyright © 2014 Elsevier Inc. All rights reserved.

Marsh management plans in practice: Do they work in coastal Louisiana, USA?

NASA Astrophysics Data System (ADS)

Cowan, James H.; Turner, R. Eugene; Cahoon, Donald R.

1988-01-01

Louisiana's coastal wetlands represent about 41% of the nation's total and are extensively managed for fish, fur, and waterfowl. Marsh management plans (MMPs) are currently used to avoid potential user conflicts and are believed to be a best management practice for specific management goals. In this article, we define MMPs and examine their variety, history, impacts, and future. A MMP is an organized written plan submitted to state and federal permitting agencies for approval and whose purpose is to regulate wetland habitat quantity and quality (control land loss and enhance productivity). MMPs are usually implemented by making structural modifications in the marsh, primarily by using a variety of water control structures in levees to impound or semi-impound managed areas. It appears that MMPs using impoundments are only marginally successful in achieving and often contradict management goals. Although 20% of coastal Louisiana may be in MMPs by the year 2000, conflict resolution of public and private goals is compromised by a surfeit of opinion and dearth of data and experience. Based on interpretation of these results, we believe the next phase of management should include scientific studies of actual impacts, utilization of post-construction monitoring data, inventory of existing MMPs, development of new techniques, and determination of cumulative impacts.

Human Factors Guidance for Control Room and Digital Human-System Interface Design and Modification, Guidelines for Planning, Specification, Design, Licensing, Implementation, Training, Operation and Maintenance

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. Fink, D. Hill, J. O'Hara

2004-11-30

Nuclear plant operators face a significant challenge designing and modifying control rooms. This report provides guidance on planning, designing, implementing and operating modernized control rooms and digital human-system interfaces.

43 CFR 10005.15 - Planning and management techniques applicable to the plan.

Code of Federal Regulations, 2011 CFR

2011-10-01

... applicable to the plan. 10005.15 Section 10005.15 Public Lands: Interior Regulations Relating to Public Lands... AND IMPLEMENTING THE COMMISSION'S MITIGATION AND CONSERVATION PLAN § 10005.15 Planning and management techniques applicable to the plan. The Commission recognizes that there are a wide range of techniques that...

Optimizing clinical operations as part of a global emergency medicine initiative in Kumasi, Ghana: application of Lean manufacturing principals to low-resource health systems.

PubMed

Carter, Patrick M; Desmond, Jeffery S; Akanbobnaab, Christopher; Oteng, Rockefeller A; Rominski, Sarah D; Barsan, William G; Cunningham, Rebecca M

2012-03-01

Although many global health programs focus on providing clinical care or medical education, improving clinical operations can have a significant effect on patient care delivery, especially in developing health systems without high-level operations management. Lean manufacturing techniques have been effective in decreasing emergency department (ED) length of stay, patient waiting times, numbers of patients leaving without being seen, and door-to-balloon times for ST-elevation myocardial infarction in developed health systems, but use of Lean in low to middle income countries with developing emergency medicine (EM) systems has not been well characterized. To describe the application of Lean manufacturing techniques to improve clinical operations at Komfo Anokye Teaching Hospital (KATH) in Ghana and to identify key lessons learned to aid future global EM initiatives. A 3-week Lean improvement program focused on the hospital admissions process at KATH was completed by a 14-person team in six stages: problem definition, scope of project planning, value stream mapping, root cause analysis, future state planning, and implementation planning. The authors identified eight lessons learned during our use of Lean to optimize the operations of an ED in a global health setting: 1) the Lean process aided in building a partnership with Ghanaian colleagues; 2) obtaining and maintaining senior institutional support is necessary and challenging; 3) addressing power differences among the team to obtain feedback from all team members is critical to successful Lean analysis; 4) choosing a manageable initial project is critical to influence long-term Lean use in a new environment; 5) data intensive Lean tools can be adapted and are effective in a less resourced health system; 6) several Lean tools focused on team problem-solving techniques worked well in a low-resource system without modification; 7) using Lean highlighted that important changes do not require an influx of resources; and 8) despite different levels of resources, root causes of system inefficiencies are often similar across health care systems, but require unique solutions appropriate to the clinical setting. Lean manufacturing techniques can be successfully adapted for use in developing health systems. Lessons learned from this Lean project will aid future introduction of advanced operations management techniques in low- to middle-income countries. © 2012 by the Society for Academic Emergency Medicine.

Optimizing Clinical Operations as part of a Global Emergency Medicine Initiative in Kumasi, Ghana: Application of Lean Manufacturing Principals to Low Resource Health Systems

PubMed Central

Carter, Patrick M.; Desmond, Jeffery S.; Akanbobnaab, Christopher; Oteng, Rockefeller A.; Rominski, Sarah; Barsan, William G.; Cunningham, Rebecca

2012-01-01

Background Although many global health programs focus on providing clinical care or medical education, improving clinical operations can have a significant effect on patient care delivery, especially in developing health systems without high-level operations management. Lean manufacturing techniques have been effective in decreasing emergency department (ED) length of stay, patient waiting times, numbers of patients leaving without being seen, and door-to-balloon times for ST-elevation myocardial infarction in developed health systems; but use of Lean in low to middle income countries with developing emergency medicine systems has not been well characterized. Objectives To describe the application of Lean manufacturing techniques to improve clinical operations at Komfo Anokye Teaching Hospital in Ghana and to identify key lessons learned to aid future global EM initiatives. Methods A three-week Lean improvement program focused on the hospital admissions process at Komfo Anokye Teaching Hospital was completed by a 14-person team in six stages: problem definition, scope of project planning, value stream mapping, root cause analysis, future state planning, and implementation planning. Results The authors identified eight lessons learned during our use of Lean to optimize the operations of an ED in a global health setting: 1) the Lean process aided in building a partnership with Ghanaian colleagues; 2) obtaining and maintaining senior institutional support is necessary and challenging; 3) addressing power differences among the team to obtain feedback from all team members is critical to successful Lean analysis; 4) choosing a manageable initial project is critical to influence long-term Lean use in a new environment; 5) data intensive Lean tools can be adapted and are effective in a less resourced health system; 6) several Lean tools focused on team problem solving techniques worked well in a low resource system without modification; 7) using Lean highlighted that important changes do not require an influx of resources; 8) despite different levels of resources, root causes of system inefficiencies are often similar across health care systems, but require unique solutions appropriate to the clinical setting. Conclusions Lean manufacturing techniques can be successfully adapted for use in developing health systems. Lessons learned from this Lean project will aid future introduction of advanced operations management techniques in low to middle income countries. PMID:22435868

Methods of Single Station and Limited Data Analysis and Forecasting

DTIC Science & Technology

1985-08-15

example using real data. Discusses modifications of SSA technique in certain climatological regimes and describes some statistical tech- niques for SSA of... caster has access to radar or satellite observations, or any computer products during the period of his isolation. Where calculations are involved, it is...chapters of the text will deal with special topics such as modifications of the SSA technique that must be considered for certain clima- tological regimes

High-resolution studies of the HF ionospheric modification interaction region

NASA Technical Reports Server (NTRS)

Duncan, L. M.; Sheerin, J. P.

1985-01-01

The use of the pulse edge analysis technique to explain ionospheric modifications caused by high-power HF radio waves is discussed. The technique, implemented at the Arecibo Observatory, uses long radar pulses and very rapid data sampling. A comparison of the pulse leading and trailing edge characteristics is obtained and the comparison is used to estimate the relative changes in the interaction region height and layer width; an example utilizing this technique is provided. Main plasma line overshoot and miniovershoot were studied from the pulse edge observations; the observations at various HF pulsings and radar resolutions are graphically presented. From the pulse edge data the development and the occurrence of main plasma line overshoot and miniovershoot are explained. The theories of soliton formation and collapse, wave ducting, profile modification, and parametric instabilities are examined as a means of explaining main plasma line overshoots and miniovershoots.

Enrichment and separation techniques for large-scale proteomics analysis of the protein post-translational modifications.

PubMed

Huang, Junfeng; Wang, Fangjun; Ye, Mingliang; Zou, Hanfa

2014-11-06

Comprehensive analysis of the post-translational modifications (PTMs) on proteins at proteome level is crucial to elucidate the regulatory mechanisms of various biological processes. In the past decades, thanks to the development of specific PTM enrichment techniques and efficient multidimensional liquid chromatography (LC) separation strategy, the identification of protein PTMs have made tremendous progress. A huge number of modification sites for some major protein PTMs have been identified by proteomics analysis. In this review, we first introduced the recent progresses of PTM enrichment methods for the analysis of several major PTMs including phosphorylation, glycosylation, ubiquitination, acetylation, methylation, and oxidation/reduction status. We then briefly summarized the challenges for PTM enrichment. Finally, we introduced the fractionation and separation techniques for efficient separation of PTM peptides in large-scale PTM analysis. Copyright © 2014 Elsevier B.V. All rights reserved.

Procedures and criteria for increasing the earthquake resistance level of electrical substations and special installations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Couch, R.W.; Deacon, R.J.

1973-09-30

This report defines a procedure and provides basic information needed to determine the modifications required to make electrical substations and special installations of the Bonneville Power Administration (BPA) more resistant to strong earthquake ground motion. It also provides a procedure for developing an effective plan for establishing the sequence, or priority, of providing the required modifications.

Modifications made to a hacksaw for use on EVA 3

NASA Image and Video Library

2005-08-02

S114-E-6034 (2 August 2005) --- This image taken aboard the Shuttle Discovery shows the modifications the crew has made to a hacksaw they will carry with them during a spacewalk planned for Wednesday. The hacksaw could be used if needed to cut off a thermal protection system gap filler that is protruding from the underside of Discovery.

23 CFR Appendix D to Subpart A of... - Guidance Criteria for Evaluating Requests for Modifications to the National Highway System

Code of Federal Regulations, 2012 CFR

2012-04-01

... 23 Highways 1 2012-04-01 2012-04-01 false Guidance Criteria for Evaluating Requests for Modifications to the National Highway System D Appendix D to Subpart A of Part 470 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PLANNING AND RESEARCH HIGHWAY SYSTEMS Federal-aid Highway Systems Pt...

23 CFR Appendix D to Subpart A of... - Guidance Criteria for Evaluating Requests for Modifications to the National Highway System

Code of Federal Regulations, 2013 CFR

2013-04-01

... 23 Highways 1 2013-04-01 2013-04-01 false Guidance Criteria for Evaluating Requests for Modifications to the National Highway System D Appendix D to Subpart A of Part 470 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PLANNING AND RESEARCH HIGHWAY SYSTEMS Federal-aid Highway Systems Pt...

23 CFR Appendix D to Subpart A of... - Guidance Criteria for Evaluating Requests for Modifications to the National Highway System

Code of Federal Regulations, 2014 CFR

2014-04-01

... 23 Highways 1 2014-04-01 2014-04-01 false Guidance Criteria for Evaluating Requests for Modifications to the National Highway System D Appendix D to Subpart A of Part 470 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PLANNING AND RESEARCH HIGHWAY SYSTEMS Federal-aid Highway Systems Pt...

Test Plan Framework for Cross Domain Solution (CDS) Devices

DTIC Science & Technology

2010-06-01

modification to the CASTER software to reflect the latest changes to RDAC is being discussed by the developers with input by the independent labs and NSA...7 xii THIS PAGE INTENTIONALLY LEFT BLANK xiii LIST OF ABBREVIATIONS AND ACRONYMS CASTER Certification...protecting information and information systems from unauthorized access, use, disclosure, disruption, modification , or destruction. While this is a

18 CFR 725.3 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-04-01

... result in the long- or short-term adverse impacts associated with: (a) The occupancy or modification of... apply to Level A and B regional or river basin planning activities carried out by regional planning sponsors including consideration of inclusion of site specific projects in Level A or B regional or river...

18 CFR 725.3 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-04-01

... result in the long- or short-term adverse impacts associated with: (a) The occupancy or modification of... apply to Level A and B regional or river basin planning activities carried out by regional planning sponsors including consideration of inclusion of site specific projects in Level A or B regional or river...

18 CFR 725.3 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-04-01

... result in the long- or short-term adverse impacts associated with: (a) The occupancy or modification of... apply to Level A and B regional or river basin planning activities carried out by regional planning sponsors including consideration of inclusion of site specific projects in Level A or B regional or river...

30 CFR 746.18 - Mining plan modification.

Code of Federal Regulations, 2013 CFR

2013-07-01

... operations on lands containing leased Federal coal pursuant to a permit revision issued by the regulatory... plan which would affect the conditions of its approval pursuant to Federal law or regulation other than... would extend coal mining and reclamation operations onto leased Federal coal lands for the first time...

30 CFR 746.18 - Mining plan modification.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operations on lands containing leased Federal coal pursuant to a permit revision issued by the regulatory... plan which would affect the conditions of its approval pursuant to Federal law or regulation other than... would extend coal mining and reclamation operations onto leased Federal coal lands for the first time...

30 CFR 746.18 - Mining plan modification.

Code of Federal Regulations, 2014 CFR

2014-07-01

... operations on lands containing leased Federal coal pursuant to a permit revision issued by the regulatory... plan which would affect the conditions of its approval pursuant to Federal law or regulation other than... would extend coal mining and reclamation operations onto leased Federal coal lands for the first time...

30 CFR 746.18 - Mining plan modification.

Code of Federal Regulations, 2012 CFR

2012-07-01

... operations on lands containing leased Federal coal pursuant to a permit revision issued by the regulatory... plan which would affect the conditions of its approval pursuant to Federal law or regulation other than... would extend coal mining and reclamation operations onto leased Federal coal lands for the first time...

49 CFR 244.13 - Subjects to be addressed in a Safety Integration Plan involving an amalgamation of operations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... shall identify classroom and field courses, lectures, tests, and other educational or instructional... shall identify the post-accident toxicological testing, reasonable cause testing, and random alcohol and... and maintenance, and any planned amendments or modifications to capital improvement and research and...

49 CFR 244.13 - Subjects to be addressed in a Safety Integration Plan involving an amalgamation of operations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... shall identify classroom and field courses, lectures, tests, and other educational or instructional... shall identify the post-accident toxicological testing, reasonable cause testing, and random alcohol and... and maintenance, and any planned amendments or modifications to capital improvement and research and...

49 CFR 244.13 - Subjects to be addressed in a Safety Integration Plan involving an amalgamation of operations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... shall identify classroom and field courses, lectures, tests, and other educational or instructional... shall identify the post-accident toxicological testing, reasonable cause testing, and random alcohol and... and maintenance, and any planned amendments or modifications to capital improvement and research and...

49 CFR 244.13 - Subjects to be addressed in a Safety Integration Plan involving an amalgamation of operations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... shall identify classroom and field courses, lectures, tests, and other educational or instructional... shall identify the post-accident toxicological testing, reasonable cause testing, and random alcohol and... and maintenance, and any planned amendments or modifications to capital improvement and research and...

40 CFR 790.50 - Submission of study plans.

Code of Federal Regulations, 2013 CFR

2013-07-01

... no letter of intent to conduct the test had been submitted as described in § 790.45(e) and (f). (e... CONTROL ACT (CONTINUED) PROCEDURES GOVERNING TESTING CONSENT AGREEMENTS AND TEST RULES Implementation, Enforcement, and Modification of Test Rules § 790.50 Submission of study plans. (a) Who must submit study...

40 CFR 790.50 - Submission of study plans.

Code of Federal Regulations, 2012 CFR

2012-07-01

... no letter of intent to conduct the test had been submitted as described in § 790.45(e) and (f). (e... CONTROL ACT (CONTINUED) PROCEDURES GOVERNING TESTING CONSENT AGREEMENTS AND TEST RULES Implementation, Enforcement, and Modification of Test Rules § 790.50 Submission of study plans. (a) Who must submit study...

40 CFR 790.50 - Submission of study plans.

Code of Federal Regulations, 2014 CFR

2014-07-01

... no letter of intent to conduct the test had been submitted as described in § 790.45(e) and (f). (e... CONTROL ACT (CONTINUED) PROCEDURES GOVERNING TESTING CONSENT AGREEMENTS AND TEST RULES Implementation, Enforcement, and Modification of Test Rules § 790.50 Submission of study plans. (a) Who must submit study...

Seals and Sealing Techniques

NASA Technical Reports Server (NTRS)

1972-01-01

Developments by the aerospace industry in seals and sealing techniques are announced for possible use in other areas. The announcements presented are grouped as: sealing techniques for cryogenic fluids, high pressure applications, and modification for improved performance.

Feasibility of the partial-single arc technique in RapidArc planning for prostate cancer treatment

PubMed Central

Rana, Suresh; Cheng, ChihYao

2013-01-01

The volumetric modulated arc therapy (VMAT) technique, in the form of RapidArc, is widely used to treat prostate cancer. The full-single arc (f-SA) technique in RapidArc planning for prostate cancer treatment provides efficient treatment, but it also delivers a higher radiation dose to the rectum. This study aimed to compare the dosimetric results from the new partial-single arc (p-SA) technique with those from the f-SA technique in RapidArc planning for prostate cancer treatment. In this study, 10 patients with low-risk prostate cancer were selected. For each patient, two sets of RapidArc plans (f-SA and p-SA) were created in the Eclipse treatment planning system. The f-SA plan was created using one full arc, and the p-SA plan was created using planning parameters identical to those of the f-SA plan but with anterior and posterior avoidance sectors. Various dosimetric parameters of the f-SA and p-SA plans were evaluated and compared for the same target coverage and identical plan optimization parameters. The f-SA and p-SA plans showed an average difference of ±1% for the doses to the planning target volume (PTV), and there were no clear differences in dose homogeneity or plan conformity. In comparison to the f-SA technique, the p-SA technique reduced the doses to the rectum by approximately 6.1% to 21.2%, to the bladder by approximately 10.3% to 29.5%, and to the penile bulb by approximately 2.2%. In contrast, the dose to the femoral heads, the integral dose, and the number of monitor units were higher in the p-SA plans by approximately 34.4%, 7.7%, and 9.2%, respectively. In conclusion, it is feasible to use the p-SA technique for RapidArc planning for prostate cancer treatment. For the same PTV coverage and identical plan optimization parameters, the p-SA technique is better in sparing the rectum and bladder without compromising plan conformity or target homogeneity when compared to the f-SA technique. PMID:23845140

Development of a program logic model and evaluation plan for a participatory ergonomics intervention in construction.

PubMed

Jaegers, Lisa; Dale, Ann Marie; Weaver, Nancy; Buchholz, Bryan; Welch, Laura; Evanoff, Bradley

2014-03-01

Intervention studies in participatory ergonomics (PE) are often difficult to interpret due to limited descriptions of program planning and evaluation. In an ongoing PE program with floor layers, we developed a logic model to describe our program plan, and process and summative evaluations designed to describe the efficacy of the program. The logic model was a useful tool for describing the program elements and subsequent modifications. The process evaluation measured how well the program was delivered as intended, and revealed the need for program modifications. The summative evaluation provided early measures of the efficacy of the program as delivered. Inadequate information on program delivery may lead to erroneous conclusions about intervention efficacy due to Type III error. A logic model guided the delivery and evaluation of our intervention and provides useful information to aid interpretation of results. © 2013 Wiley Periodicals, Inc.

Development of a Program Logic Model and Evaluation Plan for a Participatory Ergonomics Intervention in Construction

PubMed Central

Jaegers, Lisa; Dale, Ann Marie; Weaver, Nancy; Buchholz, Bryan; Welch, Laura; Evanoff, Bradley

2013-01-01

Background Intervention studies in participatory ergonomics (PE) are often difficult to interpret due to limited descriptions of program planning and evaluation. Methods In an ongoing PE program with floor layers, we developed a logic model to describe our program plan, and process and summative evaluations designed to describe the efficacy of the program. Results The logic model was a useful tool for describing the program elements and subsequent modifications. The process evaluation measured how well the program was delivered as intended, and revealed the need for program modifications. The summative evaluation provided early measures of the efficacy of the program as delivered. Conclusions Inadequate information on program delivery may lead to erroneous conclusions about intervention efficacy due to Type III error. A logic model guided the delivery and evaluation of our intervention and provides useful information to aid interpretation of results. PMID:24006097

Technical Note: Improving the VMERGE treatment planning algorithm for rotational radiotherapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaddy, Melissa R., E-mail: mrgaddy@ncsu.edu; Papp,

2016-07-15

Purpose: The authors revisit the VMERGE treatment planning algorithm by Craft et al. [“Multicriteria VMAT optimization,” Med. Phys. 39, 686–696 (2012)] for arc therapy planning and propose two changes to the method that are aimed at improving the achieved trade-off between treatment time and plan quality at little additional planning time cost, while retaining other desirable properties of the original algorithm. Methods: The original VMERGE algorithm first computes an “ideal,” high quality but also highly time consuming treatment plan that irradiates the patient from all possible angles in a fine angular grid with a highly modulated beam and then makesmore » this plan deliverable within practical treatment time by an iterative fluence map merging and sequencing algorithm. We propose two changes to this method. First, we regularize the ideal plan obtained in the first step by adding an explicit constraint on treatment time. Second, we propose a different merging criterion that comprises of identifying and merging adjacent maps whose merging results in the least degradation of radiation dose. Results: The effect of both suggested modifications is evaluated individually and jointly on clinical prostate and paraspinal cases. Details of the two cases are reported. Conclusions: In the authors’ computational study they found that both proposed modifications, especially the regularization, yield noticeably improved treatment plans for the same treatment times than what can be obtained using the original VMERGE method. The resulting plans match the quality of 20-beam step-and-shoot IMRT plans with a delivery time of approximately 2 min.« less

Germline Genetic Modification and Identity: the Mitochondrial and Nuclear Genomes.

PubMed

Scott, Rosamund; Wilkinson, Stephen

2017-12-01

In a legal 'first', the UK removed a prohibition against modifying embryos in human reproduction, to enable mitochondrial replacement techniques (MRTs), a move the Government distanced from 'germline genetic modification', which it aligned with modifying the nuclear genome. This paper (1) analyzes the uses and meanings of this term in UK/US legal and policy debates; and (2) evaluates related ethical concerns about identity. It shows that, with respect to identity, MRTs and nuclear genome editing techniques such as CRISPR/Cas-9 (now a policy topic), are not as different as has been supposed. While it does not follow that the two should be treated exactly alike, one of the central reasons offered for treating MRTs more permissively than nuclear genetic modification, and for not regarding MRTs as 'germline genetic modification', is thereby in doubt. Identity cannot, by itself, do the work thus far assigned to it, explicitly or otherwise, in law and policy.

[The modification in surgical technique of incision and closure vault of the vagina during vaginal hysterectomy on the incidence of vault haematoma].

PubMed

Malinowski, Andrzej; Mołas, Justyna; Maciołek-Blewniewska, Grazyna; Cieślak, Jarosław

2006-02-01

Vault haematoma is one of the most common complication of vaginal hysterectomy. The aim of this work was to analyse the effects of a modification of incision and closure technique of the vaginal vault on the incidence of vault haematoma after vaginal hysterectomy. The study group consisted of 333 women of whom 49 (group A) underwent vaginal hysterectomy traditional technique of incision and closure of the vaginal vault, an 284 (group B) modified technique. Following parameters were evaluated: number of vault haematomas, blood loss, postoperative fever, required antibiotics, length of hospital stay. The risk of vault haematoma was significantly lower in the group B (1,06% vs 12,4%). Loss of blood was higher in group A (310 ml vs 206 ml). Incidence of postoperative fever was in 12,2% patients from group A, and 1,4% from group B. The length of hospitalization was lower for women in group B (4,3 days compared with 7,3 days). The modification of incision and closure technique of the vaginal vault during vaginal hysterectomy is recommended to minimise intra- and postoperative complications.

Is cepstrum averaging applicable to circularly polarized electric-field data?

NASA Astrophysics Data System (ADS)

Tunnell, T.

1990-04-01

In FY 1988 a cepstrum averaging technique was developed to eliminate the ground reflections from charged particle beam (CPB) electromagnetic pulse (EMP) data. The work was done for the Los Alamos National Laboratory Project DEWPOINT at SST-7. The technique averages the cepstra of horizontally and vertically polarized electric field data (i.e., linearly polarized electric field data). This cepstrum averaging technique was programmed into the FORTRAN codes CEP and CEPSIM. Steve Knox, the principal investigator for Project DEWPOINT, asked the authors to determine if the cepstrum averaging technique could be applied to circularly polarized electric field data. The answer is, Yes, but some modifications may be necessary. There are two aspects to this answer that we need to address, namely, the Yes and the modifications. First, regarding the Yes, the technique is applicable to elliptically polarized electric field data in general: circular polarization is a special case of elliptical polarization. Secondly, regarding the modifications, greater care may be required in computing the phase in the calculation of the complex logarithm. The calculation of the complex logarithm is the most critical step in cepstrum-based analysis. This memorandum documents these findings.

A Review of Particle Swarm Optimization

NASA Astrophysics Data System (ADS)

Jain, N. K.; Nangia, Uma; Jain, Jyoti

2018-03-01

This paper presents an overview of the research progress in Particle Swarm Optimization (PSO) during 1995-2017. Fifty two papers have been reviewed. They have been categorized into nine categories based on various aspects. This technique has attracted many researchers because of its simplicity which led to many improvements and modifications of the basic PSO. Some researchers carried out the hybridization of PSO with other evolutionary techniques. This paper discusses the progress of PSO, its improvements, modifications and applications.

General method to evaluate substrate surface modification techniques for light extraction enhancement of organic light emitting diodes

NASA Astrophysics Data System (ADS)

Krummacher, B. C.; Mathai, M. K.; Choong, V.; Choulis, S. A.; So, F.; Winnacker, A.

2006-09-01

The external light output of organic light emitting diodes (OLEDs) can be increased by modifying the light emitting surface. The apparent light extraction enhancement is given by the ratio between the efficiency of the unmodified device and the efficiency of the modified device. This apparent light extraction enhancement is dependent on the OLED architecture itself and is not the correct value to judge the effectiveness of a technique to enhance light outcoupling due to substrate surface modification. We propose a general method to evaluate substrate surface modification techniques for light extraction enhancement of OLEDs independent from the device architecture. This method is experimentally demonstrated using green electrophosphorescent OLEDs with different device architectures. The substrate surface of these OLEDs was modified by applying a prismatic film to increase light outcoupling from the device stack. It was demonstrated that the conventionally measured apparent light extraction enhancement by means of the prismatic film does not reflect the actual performance of the light outcoupling technique. Rather, by comparing the light extracted out of the prismatic film to that generated in the OLED layers and coupled into the substrate (before the substrate/air interface), a more accurate evaluation of light outcoupling enhancement can be achieved. Furthermore we show that substrate surface modification can change the output spectrum of a broad band emitting OLED.

Proteomic patterns for classification of ovarian cancer and CTCL serum samples utilizing peak pairs indicative of post-translational modifications.

PubMed

Liu, Chenwei; Shea, Nancy; Rucker, Sally; Harvey, Linda; Russo, Paul; Saul, Richard; Lopez, Mary F; Mikulskis, Alvydas; Kuzdzal, Scott; Golenko, Eva; Fishman, David; Vonderheid, Eric; Booher, Susan; Cowen, Edward W; Hwang, Sam T; Whiteley, Gordon R

2007-11-01

Proteomic patterns as a potential diagnostic technology has been well established for several cancer conditions and other diseases. The use of machine learning techniques such as decision trees, neural networks, genetic algorithms, and other methods has been the basis for pattern determination. Cancer is known to involve signaling pathways that are regulated through PTM of proteins. These modifications are also detectable with high confidence using high-resolution MS. We generated data using a prOTOF mass spectrometer on two sets of patient samples: ovarian cancer and cutaneous t-cell lymphoma (CTCL) with matched normal samples for each disease. Using the knowledge of mass shifts caused by common modifications, we built models using peak pairs and compared this to a conventional technique using individual peaks. The results for each disease showed that a small number of peak pairs gave classification equal to or better than the conventional technique that used multiple individual peaks. This simple peak picking technique could be used to guide identification of important peak pairs involved in the disease process.

Enhanced removal of nitrate from water using surface modification of adsorbents--a review.

PubMed

Loganathan, Paripurnanda; Vigneswaran, Saravanamuthu; Kandasamy, Jaya

2013-12-15

Elevated concentration of nitrate results in eutrophication of natural water bodies affecting the aquatic environment and reduces the quality of drinking water. This in turn causes harm to people's health, especially that of infants and livestock. Adsorbents with the high capacity to selectively adsorb nitrate are required to effectively remove nitrate from water. Surface modifications of adsorbents have been reported to enhance their adsorption of nitrate. The major techniques of surface modification are: protonation, impregnation of metals and metal oxides, grafting of amine groups, organic compounds including surfactant coating of aluminosilicate minerals, and heat treatment. This paper reviews current information on these techniques, compares the enhanced nitrate adsorption capacities achieved by the modifications, and the mechanisms of adsorption, and presents advantages and drawbacks of the techniques. Most studies on this subject have been conducted in batch experiments. These studies need to include continuous mode column trials which have more relevance to real operating systems and pilot-plant trials. Reusability of adsorbents is important for economic reasons and practical treatment applications. However, only limited information is available on the regeneration of surface modified adsorbents. Copyright © 2013 Elsevier Ltd. All rights reserved.

MAPLE deposition of nanomaterials

NASA Astrophysics Data System (ADS)

Caricato, A. P.; Arima, V.; Catalano, M.; Cesaria, M.; Cozzoli, P. D.; Martino, M.; Taurino, A.; Rella, R.; Scarfiello, R.; Tunno, T.; Zacheo, A.

2014-05-01

The matrix-assisted pulsed laser evaporation (MAPLE) has been recently exploited for depositing films of nanomaterials by combining the advantages of colloidal inorganic nanoparticles and laser-based techniques. MAPLE-deposition of nanomaterials meeting applicative purposes demands their peculiar properties to be taken into account while planning depositions to guarantee a congruent transfer (in terms of crystal structure and geometric features) and explain the deposition outcome. In particular, since nanofluids can enhance thermal conductivity with respect to conventional fluids, laser-induced heating can induce different ablation thermal regimes as compared to the MAPLE-treatment of soft materials. Moreover, nanoparticles exhibit lower melting temperatures and can experience pre-melting phenomena as compared to their bulk counterparts, which could easily induce shape and or crystal phase modification of the material to be deposited even at very low fluences. In this complex scenario, this review paper focuses on examples of MAPLE-depositions of size and shape controlled nanoparticles for different applications highlights advantages and challenges of the MAPLE-technique. The influence of the deposition parameters on the physical mechanisms which govern the deposition process is discussed.

Suggestions for Modifications in the Teaching of General Chemistry to Accommodate Learning Disabled Students: Alternative Techniques for Teaching General Chemistry to Learning Disabled Students in the University.

ERIC Educational Resources Information Center

Habib, H. S.

A professor involved with the HELDS project (Higher Education for Learning Disabled Students) describes modifications in a general chemistry course. A syllabus lists program objectives for eight text chapters, evaluation components, and course rules. Two units are described in detail, with information presented on modifications made for LD…

[Cosmetic technique application on the modification of lip deformity after cleft lip surgery].

PubMed

Lixian, Chen; Huajun, Wang; Caixia, Gong; Qian, Zheng; Bing, Shi; Bihe, Zhang

2018-02-01

This study aims to explore the effect of cosmetic technique on the modification of lip deformity after cleft lip surgery. A total of 35 patients with postoperative cleft lip and who needed two-stage repair due to the nasolabial deformity were selected. Cosmetic technique was used to modify their lip deformities prior to the surgery. Front photos of the patients were taken before and after modification of their lip deformities. These photos were subsequently assessed by both the patients and the medical staff. The visual analogue method, Asher-McDade aesthetic index, and Mortier PB scale were used by patients and medical staff to evaluate changes in the lip shape by the cosmetic technique. Prior to the cosmetic technique application, the mean self-score of the patients and the mean scores of the medical staff were 56±13 and 3.22±1.11 points, respectively. After the cosmetic technique application, the mean self-score of the patients and the mean scores of the medical staff were 67±12 and 2.85±1.03 points, respectively. The differences were statistically significant for both the patients and the medical staff (P<0.05). Appropriate use of the cosmetic technique can modify the lip deformity after the cleft lip surgery to a certain degree. The use of this technique exerts evident effects in restoring the symmetry
of lip peak and the continuity of the labial arch and in highlighting the philtrum column.

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘E’, ROOF PLAN, ARCHITECTURAL. Sheet 22 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘D’, 2ND FLOOR PLAN, ARCHITECTURAL. Sheet 38 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘D’, MAIN FLOOR PLAN, ARCHITECTURAL. Sheet 39 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘E’, MAIN FLOOR PLAN, ARCHITECTURAL. Sheet 23 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘D’, ROOF PLAN, ARCHITECTURAL. Sheet 36 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘D’, 3RD FLOOR PLAN, ARCHITECTURAL. Sheet 37 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘B’, MAIN FLOOR PLAN, ARCHITECTURAL. Sheet 30 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘C’, 2ND FLOOR PLAN, ARCHITECTURAL. Sheet 15 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘C’, ROOF PLAN, ARCHITECTURAL. Sheet 14 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘B’, ROOF PLAN, ARCHITECTURAL. Sheet 28 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘C’, MAIN FLOOR PLAN, ARCHITECTURAL. Sheet 16 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. VEHICLE ASSEMBLY BUILDING MODIFICATIONS. NASA John F. Kennedy Space Center, Florida. File Number 79K05424, Seelye Stevenson Value & Knecht, March 1975. HIGH BAY 3, EXTENSIBLE WORK PLATFORM ‘B’, 2ND FLOOR PLAN, ARCHITECTURAL. Sheet 29 of 207 - Cape Canaveral Air Force Station, Launch Complex 39, Vehicle Assembly Building, VAB Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Military Retirement: Background and Recent Developments

DTIC Science & Technology

2016-09-12

be made. However, others have argued that past modifications intended to save money have had a deleterious effect on military recruiting and...In addition, some have argued that past modifications to the system intended to save money have had a deleterious effect on military recruiting and...to accrue tax- free . As such, a Roth plan is typically a better savings vehicle for young, low-income individuals who typically

Economic Effects of Precipitation Enhancement in the Corn Belt.

NASA Astrophysics Data System (ADS)

Gapcia, Philip; Changnon, Stanley; Pinar, Musa

1990-01-01

Policy formulation in weather modification requires an understanding of the economic effects from altered weather. The focus of this study is to provide insight into the beneficiaries of a functioning weather modification technology when applied at various spatial and temporal levels. An econometric model which links the corn/scybean production to U.S. cattle, hog and poultry sectors is used to determine the effects of precipitation enhancement in the U.S. Corn Belt, a humid climatic region. A regional supply formulation permits assessment of weather modification on production, prices, revenues to producers, and savings in consumers expenditures on meat. The results provide insight into the distribution of economic effects, emphasize the importance of careful planning in the use of weather modification technology, and provide useful information on the roles of local, state, and federal governments in the support of weather modification.

Modification of NASA Langley 8 foot high temperature tunnel to provide a unique national research facility for hypersonic air-breathing propulsion systems

NASA Technical Reports Server (NTRS)

Kelly, H. N.; Wieting, A. R.

1984-01-01

A planned modification of the NASA Langley 8-Foot High Temperature Tunnel to make it a unique national research facility for hypersonic air-breathing propulsion systems is described, and some of the ongoing supporting research for that modification is discussed. The modification involves: (1) the addition of an oxygen-enrichment system which will allow the methane-air combustion-heated test stream to simulate air for propulsion testing; and (2) supplemental nozzles to expand the test simulation capability from the current nominal Mach number to 7.0 include Mach numbers 3.0, 4.5, and 5.0. Detailed design of the modifications is currently underway and the modified facility is scheduled to be available for tests of large scale propulsion systems by mid 1988.

40 CFR 52.270 - Significant deterioration of air quality.

Code of Federal Regulations, 2013 CFR

2013-07-01

... applicable State plan for the State of California. (b) District PSD Plans. (1) The PSD rules for Sacramento... of PSD increments. (ii) Those projects which are major stationary sources or major modifications... 83-01, 5/6/83. (2) The PSD rules for North Coast Unified Air Quality Management District are approved...

29 CFR 4211.36 - Modifications to the determination of initial liabilities, the amortization of initial...

Code of Federal Regulations, 2010 CFR

2010-07-01

..., the amortization of initial liabilities, and the allocation fraction. 4211.36 Section 4211.36 Labor... initial liabilities, and the allocation fraction. (a) General rule. A plan using any of the allocation... participation under their prior plans. An amendment under this paragraph must include an allocation fraction...

40 CFR 52.270 - Significant deterioration of air quality.

Code of Federal Regulations, 2012 CFR

2012-07-01

... applicable State plan for the State of California. (b) District PSD Plans. (1) The PSD rules for Sacramento... of PSD increments. (ii) Those projects which are major stationary sources or major modifications... 83-01, 5/6/83. (2) The PSD rules for North Coast Unified Air Quality Management District are approved...

40 CFR 52.270 - Significant deterioration of air quality.

Code of Federal Regulations, 2011 CFR

2011-07-01

... applicable State plan for the State of California. (b) District PSD Plans. (1) The PSD rules for Sacramento... of PSD increments. (ii) Those projects which are major stationary sources or major modifications... 83-01, 5/6/83. (2) The PSD rules for North Coast Unified Air Quality Management District are approved...

40 CFR 52.270 - Significant deterioration of air quality.

Code of Federal Regulations, 2014 CFR

2014-07-01

... applicable State plan for the State of California. (b) District PSD Plans. (1) The PSD rules for Sacramento... of PSD increments. (ii) Those projects which are major stationary sources or major modifications... 83-01, 5/6/83. (2) The PSD rules for North Coast Unified Air Quality Management District are approved...

30 CFR 250.912 - What plans must I submit under the Platform Verification Program?

Code of Federal Regulations, 2012 CFR

2012-07-01

... and major members of concrete-gravity and steel-gravity structures; (2) For jacket and floating... Platforms and Structures Platform Verification Program § 250.912 What plans must I submit under the Platform Verification Program? If your platform, associated structure, or major modification meets the criteria in § 250...

30 CFR 250.912 - What plans must I submit under the Platform Verification Program?

Code of Federal Regulations, 2013 CFR

2013-07-01

... and major members of concrete-gravity and steel-gravity structures; (2) For jacket and floating... Platforms and Structures Platform Verification Program § 250.912 What plans must I submit under the Platform Verification Program? If your platform, associated structure, or major modification meets the criteria in § 250...

30 CFR 250.912 - What plans must I submit under the Platform Verification Program?

Code of Federal Regulations, 2014 CFR

2014-07-01

... and major members of concrete-gravity and steel-gravity structures; (2) For jacket and floating... Platforms and Structures Platform Verification Program § 250.912 What plans must I submit under the Platform Verification Program? If your platform, associated structure, or major modification meets the criteria in § 250...

Turtle Manual.

ERIC Educational Resources Information Center

Schneider, Marlene; Robin, Arthur

This manual describes the Turtle Technique which was developed to help children with behavior problems control their own disruptive behavior. The technique differs from other behavior modification techniques in that it is based upon self-control rather than external control of disruptive behavior. The Turtle Technique first teaches the child how…

Nanotubular surface modification of metallic implants via electrochemical anodization technique.

PubMed

Wang, Lu-Ning; Jin, Ming; Zheng, Yudong; Guan, Yueping; Lu, Xin; Luo, Jing-Li

2014-01-01

Due to increased awareness and interest in the biomedical implant field as a result of an aging population, research in the field of implantable devices has grown rapidly in the last few decades. Among the biomedical implants, metallic implant materials have been widely used to replace disordered bony tissues in orthopedic and orthodontic surgeries. The clinical success of implants is closely related to their early osseointegration (ie, the direct structural and functional connection between living bone and the surface of a load-bearing artificial implant), which relies heavily on the surface condition of the implant. Electrochemical techniques for modifying biomedical implants are relatively simple, cost-effective, and appropriate for implants with complex shapes. Recently, metal oxide nanotubular arrays via electrochemical anodization have become an attractive technique to build up on metallic implants to enhance the biocompatibility and bioactivity. This article will thoroughly review the relevance of electrochemical anodization techniques for the modification of metallic implant surfaces in nanoscale, and cover the electrochemical anodization techniques used in the development of the types of nanotubular/nanoporous modification achievable via electrochemical approaches, which hold tremendous potential for bio-implant applications. In vitro and in vivo studies using metallic oxide nanotubes are also presented, revealing the potential of nanotubes in biomedical applications. Finally, an outlook of future growth of research in metallic oxide nanotubular arrays is provided. This article will therefore provide researchers with an in-depth understanding of electrochemical anodization modification and provide guidance regarding the design and tuning of new materials to achieve a desired performance and reliable biocompatibility.

Nanotubular surface modification of metallic implants via electrochemical anodization technique

PubMed Central

Wang, Lu-Ning; Jin, Ming; Zheng, Yudong; Guan, Yueping; Lu, Xin; Luo, Jing-Li

2014-01-01

Due to increased awareness and interest in the biomedical implant field as a result of an aging population, research in the field of implantable devices has grown rapidly in the last few decades. Among the biomedical implants, metallic implant materials have been widely used to replace disordered bony tissues in orthopedic and orthodontic surgeries. The clinical success of implants is closely related to their early osseointegration (ie, the direct structural and functional connection between living bone and the surface of a load-bearing artificial implant), which relies heavily on the surface condition of the implant. Electrochemical techniques for modifying biomedical implants are relatively simple, cost-effective, and appropriate for implants with complex shapes. Recently, metal oxide nanotubular arrays via electrochemical anodization have become an attractive technique to build up on metallic implants to enhance the biocompatibility and bioactivity. This article will thoroughly review the relevance of electrochemical anodization techniques for the modification of metallic implant surfaces in nanoscale, and cover the electrochemical anodization techniques used in the development of the types of nanotubular/nanoporous modification achievable via electrochemical approaches, which hold tremendous potential for bio-implant applications. In vitro and in vivo studies using metallic oxide nanotubes are also presented, revealing the potential of nanotubes in biomedical applications. Finally, an outlook of future growth of research in metallic oxide nanotubular arrays is provided. This article will therefore provide researchers with an in-depth understanding of electrochemical anodization modification and provide guidance regarding the design and tuning of new materials to achieve a desired performance and reliable biocompatibility. PMID:25258532

Performance and durability of high emittance heat receiver surfaces for solar dynamic power systems

NASA Technical Reports Server (NTRS)

Degroh, Kim K.; Roig, David M.; Burke, Christopher A.; Shah, Dilipkumar R.

1994-01-01

Haynes 188, a cobalt-based superalloy, will be used to make thermal energy storage (TES) containment canisters for a 2 kW solar dynamic ground test demonstrator (SD GTD). Haynes 188 containment canisters with a high thermal emittance (epsilon) are desired for radiating heat away from local hot spots, improving the heating distribution, which will in turn improve canister service life. In addition to needing a high emittance, the surface needs to be durable in an elevated temperature, high vacuum environment for an extended time period. Thirty-five Haynes 188 samples were exposed to 14 different types of surface modification techniques for emittance and vacuum heat treatment (VHT) durability enhancement evaluation. Optical properties were obtained for the modified surfaces. Emittance enhanced samples were exposed to VHT for up to 2692 hours at 827 C and less than or equal to 10(exp -6) torr with integral thermal cycling. Optical properties were taken intermittently during exposure, and after final VHT exposure. The various surface modification treatments increased the emittance of pristine Haynes 188 from 0.11 up to 0.86. Seven different surface modification techniques were found to provide surfaces which met the SD GTD receiver VHT durability requirement. Of the 7 surface treatments, 2 were found to display excellent VHT durability: an alumina based (AB) coating and a zirconia based coating. The alumina based coating was chosen for the epsilon enhancement surface modification technique for the SD GTD receiver. Details of the performance and vacuum heat treatment durability of this coating and other Haynes 188 emittance surface modification techniques are discussed. Technology from this program will lead to successful demonstration of solar dynamic power for space applications, and has potential for application in other systems requiring high emittance surfaces.

Preoperative ultrasound still valuable for radio-cephalic arteriovenous fistula creation?

PubMed

Pajek, Jernej; Malovrh, Marko

2017-03-06

Radio-cephalic arteriovenous fistula is a prototype hemodialysis access with small incidences of infection and distal ischemia, it spares proximal veins for future access use and it helps in the maturation of veins that may be used for more proximal access creations. This access type is prone to higher early failure rates compared to more proximal fistulas and there are unsolved uncertainties regarding exact ultrasound parameters predictive of fistula outcome. Evolution of ultrasound use has yielded several functional parameters that can be measured in addition to anatomical lumen sizes, which remain core parameters on which the decision to construct fistula in radio-cephalic forearm position is based. We propose to use arterial hyperemic response and wall morphology to aid in this decision when radial artery diameter falls in the interval with predictive uncertainty of 1.6-1.9 mm and to use venous flow pattern, respiratory variation, radial artery status and possibly venous distensibility when cephalic vein augmented diameter lies in the borderline interval of 2-2.4 mm. Ultrasound preoperative mapping and planning should be followed by expert surgical technique and several technique modifications of the classical end-to-side approach are possible to enhance operation outcome and diminish the incidence of stenosis most often present at juxta-anastomotic location. In our experience radio-cephalic arteriovenous fistula remains the golden standard for hemodialysis access and preoperative ultrasound the single best imaging modality to plan the operation and predict its success.

Complex angular and torsional deformities (distal femoral malunions). Preoperative planning using stereolithography and surgical correction with locking plate fixation in four dogs.

PubMed

DeTora, Michael D; Boudrieau, Randy J

2016-09-20

To describe the surgical technique of complex distal femoral deformity correction with the aid of stereolithography apparatus (SLA) biomodels, stabilized with locking plate fixation. Full-size replica epoxy bone biomodels of the affected femurs (4 dogs/ 5 limbs) were used as templates for surgical planning. A rehearsal procedure was performed on the biomodels aided by a guide wire technique and stabilized with locking plate fixation. Surgery performed in all dogs was guided by the rehearsal procedure. All pre-contoured implants were subsequently used in the definitive surgical procedure with minimal modification. All dogs had markedly improved, with near normal functional outcomes; all but one had a mild persistent lameness at the final in-hospital follow-up examination (mean: 54.4 weeks; range: 24-113 weeks after surgery). All femurs healed without complications (mean: 34 weeks, median: 12 weeks; range: 8-12 weeks for closing osteotomies, and 26-113 weeks for opening wedge osteotomies). Long-term follow-up examination (mean: 28.6 months; range: 5-42 months) revealed all but one owner to be highly satisfied with the outcome. Complications were observed in two dogs: prolonged tibiotarsal joint decreased flexion that resolved with physical therapy. In one of these dogs, iatrogenic transection of the long digital extensor tendon was repaired, and the other had a peroneal nerve neurapraxia. Stereolithography apparatus biomodels and rehearsal surgery simplified the definitive surgical corrections of complex femoral malunions and resulted in good functional outcomes.

An investigation of networking techniques for the ASRM facility

NASA Technical Reports Server (NTRS)

Moorhead, Robert J., II; Smith, Wayne D.; Thompson, Dale R.

1992-01-01

This report is based on the early design concepts for a communications network for the Advanced Solid Rocket Motor (ASRM) facility being built at Yellow Creek near Iuka, MS. The investigators have participated in the early design concepts and in the evaluation of the initial concepts. The continuing system design effort and any modification of the plan will require a careful evaluation of the required bandwidth of the network, the capabilities of the protocol, and the requirements of the controllers and computers on the network. The overall network, which is heterogeneous in protocol and bandwidth, is being modeled, analyzed, simulated, and tested to obtain some degree of confidence in its performance capabilities and in its performance under nominal and heavy loads. The results of the proposed work should have an impact on the design and operation of the ASRM facility.

Design of Quiet Rotorcraft Approach Trajectories: Verification Phase

NASA Technical Reports Server (NTRS)

Padula, Sharon L.

2010-01-01

Flight testing that is planned for October 2010 will provide an opportunity to evaluate rotorcraft trajectory optimization techniques. The flight test will involve a fully instrumented MD-902 helicopter, which will be flown over an array of microphones. In this work, the helicopter approach trajectory is optimized via a multiobjective genetic algorithm to improve community noise, passenger comfort, and pilot acceptance. Previously developed optimization strategies are modified to accommodate new helicopter data and to increase pilot acceptance. This paper describes the MD-902 trajectory optimization plus general optimization strategies and modifications that are needed to reduce the uncertainty in noise predictions. The constraints that are imposed by the flight test conditions and characteristics of the MD-902 helicopter limit the testing possibilities. However, the insights that will be gained through this research will prove highly valuable.

Engineering Large Animal Species to Model Human Diseases.

PubMed

Rogers, Christopher S

2016-07-01

Animal models are an important resource for studying human diseases. Genetically engineered mice are the most commonly used species and have made significant contributions to our understanding of basic biology, disease mechanisms, and drug development. However, they often fail to recreate important aspects of human diseases and thus can have limited utility as translational research tools. Developing disease models in species more similar to humans may provide a better setting in which to study disease pathogenesis and test new treatments. This unit provides an overview of the history of genetically engineered large animals and the techniques that have made their development possible. Factors to consider when planning a large animal model, including choice of species, type of modification and methodology, characterization, production methods, and regulatory compliance, are also covered. © 2016 by John Wiley & Sons, Inc. Copyright © 2016 John Wiley & Sons, Inc.

Consulting the oracle: ten lessons from using the Delphi technique in nursing research.

PubMed

Keeney, Sinead; Hasson, Felicity; McKenna, Hugh

2006-01-01

The aim of this paper was to provide insight into the Delphi technique by outlining our personal experiences during its use over a 10-year period in a variety of applications. As a means of achieving consensus on an issue, the Delphi research method has become widely used in healthcare research generally and nursing research in particular. The literature on this technique is expanding, mainly addressing what it is and how it should be used. However, there is still much confusion and uncertainty surrounding it, particularly about issues such as modifications, consensus, anonymity, definition of experts, how 'experts' are selected and how non-respondents are pursued. This issues that arise when planning and carrying out a Delphi study include the definition of consensus; the issue of anonymity vs. quasi-anonymity for participants; how to estimate the time needed to collect the data, analyse each 'round', feed back results to participants, and gain their responses to this feedback; how to define and select the 'experts' who will be asked to participate; how to enhance response rates; and how many 'rounds' to conduct. Many challenges and questions are raised when using the Delphi technique, but there is no doubt that it is an important method for achieving consensus on issues where none previously existed. Researchers need to adapt the method to suit their particular study.

Cost Savings Potential of Modification to the Standard Light Rail Vehicle Specification

DOT National Transportation Integrated Search

1979-02-01

This report describes an assessment of the Standard Light Rail Vehicle (SLRV) specification to determine whether the relaxation or modification of some requirements could result in a significant reduction in vehicle costs. A Technique of Assessment b...

On the Teaching of a Self-Modification Course

ERIC Educational Resources Information Center

Tasto, Donald L.

1976-01-01

Discusses teaching techniques, course content, strategies, and problems of teaching a behavior modification course to university students. Course target areas include subjects such as anxiety control, fear elimination, weight control, smoking reduction, interpersonal interaction, assertiveness, and exercise maintenance. (Author/DB)

Single-cell epigenomics: techniques and emerging applications.

PubMed

Schwartzman, Omer; Tanay, Amos

2015-12-01

Epigenomics is the study of the physical modifications, associations and conformations of genomic DNA sequences, with the aim of linking these with epigenetic memory, cellular identity and tissue-specific functions. While current techniques in the field are characterizing the average epigenomic features across large cell ensembles, the increasing interest in the epigenetics within complex and heterogeneous tissues is driving the development of single-cell epigenomics. We review emerging single-cell methods for capturing DNA methylation, chromatin accessibility, histone modifications, chromosome conformation and replication dynamics. Together, these techniques are rapidly becoming a powerful tool in studies of cellular plasticity and diversity, as seen in stem cells and cancer.

Texture Modification of the Shuttle Landing Facility Runway at the NASA Kennedy Space Center

NASA Technical Reports Server (NTRS)

Daugherty, Robert H.; Yager, Thomas J.

1996-01-01

This paper describes the test procedures and the selection criteria used in selecting the best runway surface texture modification at the Kennedy Space Center (KSC) Shuttle Landing Facility (SLF) to reduce Orbiter tire wear. The new runway surface may ultimately result in an increase of allowable crosswinds for launch and landing operations. The modification allows launch and landing operations in 20-kt crosswinds if desired. This 5-kt increase over the previous 15-kt limit drastically increases landing safety and the ability to make on-time launches to support missions where space station rendezvous is planned.

Genomic tools and and prospects for new breeding techniques in flower bulb crops

USDA-ARS?s Scientific Manuscript database

For many of the new breeding techniques, sequence information is of the utmost importance. In addition to current breeding techniques, such as marker-assisted selection (MAS) and genetic modification (GM), new breeding techniques such as zinc finger nucleases, oligonucleotide-mediated mutagenesis, R...

Respiratory gating and multifield technique radiotherapy for esophageal cancer.

PubMed

Ohta, Atsushi; Kaidu, Motoki; Tanabe, Satoshi; Utsunomiya, Satoru; Sasamoto, Ryuta; Maruyama, Katsuya; Tanaka, Kensuke; Saito, Hirotake; Nakano, Toshimichi; Shioi, Miki; Takahashi, Haruna; Kushima, Naotaka; Abe, Eisuke; Aoyama, Hidefumi

2017-03-01

To investigate the effects of a respiratory gating and multifield technique on the dose-volume histogram (DVH) in radiotherapy for esophageal cancer. Twenty patients who underwent four-dimensional computed tomography for esophageal cancer were included. We retrospectively created the four treatment plans for each patient, with or without the respiratory gating and multifield technique: No gating-2-field, No gating-4-field, Gating-2-field, and Gating-4-field plans. We compared the DVH parameters of the lung and heart in the No gating-2-field plan with the other three plans. In the comparison of the parameters in the No gating-2-field plan, there are significant differences in the Lung V 5Gy , V 20Gy , mean dose with all three plans and the Heart V 25Gy -V 40Gy with Gating-2-field plan, V 35Gy , V 40Gy , mean dose with No Gating-4-field plan and V 30Gy -V 40Gy , and mean dose with Gating-4-field plan. The lung parameters were smaller in the Gating-2-field plan and larger in the No gating-4-field and Gating-4-field plans. The heart parameters were all larger in the No gating-2-field plan. The lung parameters were reduced by the respiratory gating technique and increased by the multifield technique. The heart parameters were reduced by both techniques. It is important to select the optimal technique according to the risk of complications.

Interactive Dose Shaping - efficient strategies for CPU-based real-time treatment planning

NASA Astrophysics Data System (ADS)

Ziegenhein, P.; Kamerling, C. P.; Oelfke, U.

2014-03-01

Conventional intensity modulated radiation therapy (IMRT) treatment planning is based on the traditional concept of iterative optimization using an objective function specified by dose volume histogram constraints for pre-segmented VOIs. This indirect approach suffers from unavoidable shortcomings: i) The control of local dose features is limited to segmented VOIs. ii) Any objective function is a mathematical measure of the plan quality, i.e., is not able to define the clinically optimal treatment plan. iii) Adapting an existing plan to changed patient anatomy as detected by IGRT procedures is difficult. To overcome these shortcomings, we introduce the method of Interactive Dose Shaping (IDS) as a new paradigm for IMRT treatment planning. IDS allows for a direct and interactive manipulation of local dose features in real-time. The key element driving the IDS process is a two-step Dose Modification and Recovery (DMR) strategy: A local dose modification is initiated by the user which translates into modified fluence patterns. This also affects existing desired dose features elsewhere which is compensated by a heuristic recovery process. The IDS paradigm was implemented together with a CPU-based ultra-fast dose calculation and a 3D GUI for dose manipulation and visualization. A local dose feature can be implemented via the DMR strategy within 1-2 seconds. By imposing a series of local dose features, equal plan qualities could be achieved compared to conventional planning for prostate and head and neck cases within 1-2 minutes. The idea of Interactive Dose Shaping for treatment planning has been introduced and first applications of this concept have been realized.

POLLUTANT CONTROL TECHNIQUES FOR PACKAGE BOILERS: HARDWARE MODIFICATIONS AND ALTERNATE FUELS

EPA Science Inventory

The report gives results of investigations of four ways to control nitrogen oxide (NOx) emissions from package boilers (both field operating boilers and boiler simulators): (1) variations in combustor operating procedure; (2) combustion modification (flue gas recirculation and st...

Photocopy of drawing. MODIFICATIONS TO CONVERT ML NO. 3 TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. MODIFICATIONS TO CONVERT ML NO. 3 TO MOBILE LAUNCHER PLATFORM NO. 1. NASA, John F. Kennedy Space Center, Florida. Drawing 79K04401, Reynolds, Smith and Hills, March, 1975. GENERAL ARRANGEMENT, MLP NO. 1, PLAN – DECK A. Sheet A13 - Cape Canaveral Air Force Station, Launch Complex 39, Mobile Launcher Platforms, Launcher Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. MODIFICATIONS TO CONVERT ML NO. 3 TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. MODIFICATIONS TO CONVERT ML NO. 3 TO MOBILE LAUNCHER PLATFORM NO. 1. NASA, John F. Kennedy Space Center, Florida. Drawing 79K04401, Reynolds, Smith and Hills, March, 1975. GENERAL ARRANGEMENT, MLP NO. 1, PLAN – DECK B. Sheet A14 - Cape Canaveral Air Force Station, Launch Complex 39, Mobile Launcher Platforms, Launcher Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

Photocopy of drawing. MODIFICATIONS TO CONVERT ML NO. 3 TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of drawing. MODIFICATIONS TO CONVERT ML NO. 3 TO MOBILE LAUNCHER PLATFORM NO. 1. NASA, John F. Kennedy Space Center, Florida. Drawing 79K04401, Reynolds, Smith and Hills, March, 1975. GENERAL ARRANGEMENT, MLP NO. 1, PLAN – DECK 0. Sheet A12 - Cape Canaveral Air Force Station, Launch Complex 39, Mobile Launcher Platforms, Launcher Road, East of Kennedy Parkway North, Cape Canaveral, Brevard County, FL

BAC Modification through Serial or Simultaneous Use of CRE/Lox Technology

PubMed Central

Parrish, Mark; Unruh, Jay; Krumlauf, Robb

2011-01-01

Bacterial Artificial Chromosomes (BACs) are vital tools in mouse genomic analyses because of their ability to propagate large inserts. The size of these constructs, however, prevents the use of conventional molecular biology techniques for modification and manipulation. Techniques such as recombineering and Cre/Lox methodologies have thus become heavily relied upon for such purposes. In this work, we investigate the applicability of Lox variant sites for serial and/or simultaneous manipulations of BACs. We show that Lox spacer mutants are very specific, and inverted repeat variants reduce Lox reaction rates through reducing the affinity of Cre for the site, while retaining some functionality. Employing these methods, we produced serial modifications encompassing four independent changes which generated a mouse HoxB BAC with fluorescent reporter proteins inserted into four adjacent Hox genes. We also generated specific, simultaneous deletions using combinations of spacer variants and inverted repeat variants. These techniques will facilitate BAC manipulations and open a new repertoire of methods for BAC and genome manipulation. PMID:21197414

Application of the CRISPR/Cas9 gene editing technique to research on functional genomes of parasites.

PubMed

Cui, Yubao; Yu, Lili

2016-12-01

The clustered regularly-interspaced short palindromic repeats (CRISPR) structural family functions as an acquired immune system in prokaryotes. Gene editing techniques have co-opted CRISPR and the associated Cas nucleases to allow for the precise genetic modification of human cells, zebrafish, mice, and other eukaryotes. Indeed, this approach has been used to induce a variety of modifications including directed insertion/deletion (InDel) of bases, gene knock-in, introduction of mutations in both alleles of a target gene, and deletion of small DNA fragments. Thus, CRISPR technology offers a precise molecular tool for directed genome modification with a range of potential applications; further, its high mutation efficiency, simple process, and low cost provide additional advantages over prior editing techniques. This paper will provide an overview of the basic structure and function of the CRISPR gene editing system as well as current and potential applications to research on parasites. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Structural characterization of thioether-bridged bacteriocins.

PubMed

Lohans, Christopher T; Vederas, John C

2014-01-01

Bacteriocins are a group of ribosomally synthesized antimicrobial peptides produced by bacteria, some of which are extensively post-translationally modified. Some bacteriocins, namely the lantibiotics and sactibiotics, contain one or more thioether bridges. However, these modifications complicate the structural elucidation of these bacteriocins using conventional techniques. This review will discuss the techniques and strategies that have been applied to determine the primary structures of lantibiotics and sactibiotics. A major challenge is to identify the topology of thioether bridges in these peptides (i.e., which amino-acid residues are involved in which bridges). Edman degradation, NMR spectroscopy and tandem MS have all been commonly applied to characterize these bacteriocins, but can be incompatible with the post-translational modifications present. Chemical modifications to the modified residues, such as desulfurization and reduction, make the treated bacteriocins more compatible to analysis by these standard peptide analytical techniques. Despite their differences in structure, similar strategies have proved useful to study the structures of both lantibiotics and sactibiotics.

An overview of biofunctionalization of metals in Japan

PubMed Central

Hanawa, Takao

2009-01-01

Surface modification is an important and predominant technique for obtaining biofunction and biocompatibility in metals for biomedical use. The surface modification technique is a process that changes the surface composition, structure and morphology of a material, leaving the bulk mechanical properties intact. A tremendous number of surface modification techniques using dry and wet processes to improve the hard tissue compatibility of titanium have been developed. Some are now commercially available. Most of these processes have been developed by Japanese institutions since the 1990s. A second approach is the immobilization of biofunctional molecules to the metal surface to control the adsorption of proteins and adhesion of cells, platelets and bacteria. The immobilization of poly(ethylene glycol) to a metal surface with electrodeposition and its effect on biofunction are reviewed. The creation of a metal–polymer composite is another way to obtain metal-based biofunctional materials. The relationship between the shear bonding strength and the chemical structure at the bonding interface of a Ti-segmentated polyurethane composite through a silane coupling agent is explained. PMID:19158014

The Mission Operations Planning Assistant

NASA Technical Reports Server (NTRS)

Schuetzle, James G.

1987-01-01

The Mission Operations Planning Assistant (MOPA) is a knowledge-based system developed to support the planning and scheduling of instrument activities on the Upper Atmospheric Research Satellite (UARS). The MOPA system represents and maintains instrument plans at two levels of abstraction in order to keep plans comprehensible to both UARS Principal Investigators and Command Management personnel. The hierarchical representation of plans also allows MOPA to automatically create detailed instrument activity plans from which spacecraft command loads may be generated. The MOPA system was developed on a Symbolics 3640 computer using the ZetaLisp and ART languages. MOPA's features include a textual and graphical interface for plan inspection and modification, recognition of instrument operational constraint violations during the planning process, and consistency maintenance between the different planning levels. This paper describes the current MOPA system.

The mission operations planning assistant

NASA Technical Reports Server (NTRS)

Schuetzle, James G.

1987-01-01

The Mission Operations Planning Assistant (MOPA) is a knowledge-based system developed to support the planning and scheduling of instrument activities on the Upper Atmospheric Research Satellite (UARS). The MOPA system represents and maintains instrument plans at two levels of abstraction in order to keep plans comprehensible to both UARS Prinicpal Investigators and Command Management personnel. The hierarchical representation of plans also allows MOPA to automatically create detailed instrument activity plans from which spacecraft command loads may be generated. The MOPA system was developed on a Symbolics 3640 computer using the ZETALISP and ART languages. MOPA's features include a textual and graphical interface for plan inspection and modification, recognition of instrument operational constraint violations during the planning process, and consistency maintenance between the different planning levels. This paper describes the current MOPA system.

A method to incorporate leakage and head scatter corrections into a tomotherapy inverse treatment planning algorithm

NASA Astrophysics Data System (ADS)

Holmes, Timothy W.

2001-01-01

A detailed tomotherapy inverse treatment planning method is described which incorporates leakage and head scatter corrections during each iteration of the optimization process, allowing these effects to be directly accounted for in the optimized dose distribution. It is shown that the conventional inverse planning method for optimizing incident intensity can be extended to include a `concurrent' leaf sequencing operation from which the leakage and head scatter corrections are determined. The method is demonstrated using the steepest-descent optimization technique with constant step size and a least-squared error objective. The method was implemented using the MATLAB scientific programming environment and its feasibility demonstrated for 2D test cases simulating treatment delivery using a single coplanar rotation. The results indicate that this modification does not significantly affect convergence of the intensity optimization method when exposure times of individual leaves are stratified to a large number of levels (>100) during leaf sequencing. In general, the addition of aperture dependent corrections, especially `head scatter', reduces incident fluence in local regions of the modulated fan beam, resulting in increased exposure times for individual collimator leaves. These local variations can result in 5% or greater local variation in the optimized dose distribution compared to the uncorrected case. The overall efficiency of the modified intensity optimization algorithm is comparable to that of the original unmodified case.

Using the Theory of Planned Behavior and Cheating Justifications to Predict Academic Misconduct

ERIC Educational Resources Information Center

Stone, Thomas H.; Jawahar, I. M.; Kisamore, Jennifer L.

2009-01-01

Purpose: The purpose of this paper is to show that academic misconduct appears to be on the rise; some research has linked academic misconduct to unethical workplace behaviors. Unlike previous empirically-driven research, this theory-based study seeks to examine the usefulness of a modification of Ajzen's theory of planned behavior to predict…

42 CFR 422.106 - Coordination of benefits with employer or union group health plans and Medicaid.

Code of Federal Regulations, 2011 CFR

2011-10-01

... benefits under these circumstances is as follows: (1) All requirements of this part that apply to the MA..., labor organization, benefit fund trustee, or Medicaid plan benefits include the following: (1) Payment... contract with the State Medicaid agency. (c) Waiver or modification of contracts with MA organizations. (1...

75 FR 59180 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Control Technique...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-27

... Promulgation of Air Quality Implementation Plans; Maryland; Control Technique Guidelines for Paper, Film, and... Technique Guidelines (CTG) for paper, film, and foil coatings. These amendments will reduce volatile organic... Promulgation of Air Quality Implementation Plans; Maryland; Control Technique Guidelines for Paper, Film, and...

Dependence of Achievable Plan Quality on Treatment Technique and Planning Goal Refinement: A Head-and-Neck Intensity Modulated Radiation Therapy Application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qi, X. Sharon, E-mail: xqi@mednet.ucla.edu; Ruan, Dan; Lee, Steve P.

2015-03-15

Purpose: To develop a practical workflow for retrospectively analyzing target and normal tissue dose–volume endpoints for various intensity modulated radiation therapy (IMRT) delivery techniques; to develop technique-specific planning goals to improve plan consistency and quality when feasible. Methods and Materials: A total of 165 consecutive head-and-neck patients from our patient registry were selected and retrospectively analyzed. All IMRT plans were generated using the same dose–volume guidelines for TomoTherapy (Tomo, Accuray), TrueBeam (TB, Varian) using fixed-field IMRT (TB-IMRT) or RAPIDARC (TB-RAPIDARC), or Siemens Oncor (Siemens-IMRT, Siemens). A MATLAB-based dose–volume extraction and analysis tool was developed to export dosimetric endpoints for eachmore » patient. With a fair stratification of patient cohort, the variation of achieved dosimetric endpoints was analyzed among different treatment techniques. Upon identification of statistically significant variations, technique-specific planning goals were derived from dynamically accumulated institutional data. Results: Retrospective analysis showed that although all techniques yielded comparable target coverage, the doses to the critical structures differed. The maximum cord doses were 34.1 ± 2.6, 42.7 ± 2.1, 43.3 ± 2.0, and 45.1 ± 1.6 Gy for Tomo, TB-IMRT, TB-RAPIDARC, and Siemens-IMRT plans, respectively. Analyses of variance showed significant differences for the maximum cord doses but no significant differences for other selected structures among the investigated IMRT delivery techniques. Subsequently, a refined technique-specific dose–volume guideline for maximum cord dose was derived at a confidence level of 95%. The dosimetric plans that failed the refined technique-specific planning goals were reoptimized according to the refined constraints. We observed better cord sparing with minimal variations for the target coverage and other organ at risk sparing for the Tomo cases, and higher parotid doses for C-arm linear accelerator–based IMRT and RAPIDARC plans. Conclusion: Patient registry–based processes allowed easy and systematic dosimetric assessment of treatment plan quality and consistency. Our analysis revealed the dependence of certain dosimetric endpoints on the treatment techniques. Technique-specific refinement of planning goals may lead to improvement in plan consistency and plan quality.« less

Benefits of online in vivo dosimetry for single-fraction total body irradiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eaton, David J., E-mail: davideaton@nhs.net; Warry, Alison J.; Trimble, Rachel E.

Use of a patient test dose before single-fraction total body irradiation (TBI) allows review of in vivo dosimetry and modification of the main treatment setup. However, use of computed tomography (CT) planning and online in vivo dosimetry may reduce the need for this additional step. Patients were treated using a supine CT-planned extended source-to-surface distance (SSD) technique with lead compensators and bolus. In vivo dosimetry was performed using thermoluminescent dosimeters (TLDs) and diodes at 10 representative anatomical locations, for both a 0.1-Gy test dose and the treatment dose. In total, 28 patients were treated between April 2007 and July 2013,more » with changes made in 10 cases (36%) following test dose results. Overall, 98.1% of measured in vivo treatment doses were within 10% of the prescribed dose, compared with 97.0% of test dose readings. Changes made following the test dose could have been applied during the single-fraction treatment itself, assuming that the dose was delivered in subportions and online in vivo dosimetry was available for all clinically important anatomical sites. This alleviates the need for a test dose, saving considerable time and resources.« less

Mothers of Invention: Hubble Engineers Push Robotic 'Evolution' to Save Telescope, Enable New Exploration

NASA Technical Reports Server (NTRS)

Morring, Frank, Jr.

2004-01-01

Robotic technology being developed out of necessity to keep the Hubble Space Telescope operating could also lead to new levels of man-machine team-work in deep-space exploration down the road-if it survives the near-term scramble for funding. Engineers here who have devoted their NASA careers to the concept of humans servicing the telescope in orbit are planning modifications to International Space Station (ISS) robots that would leave the humans on the ground. The work. forced by post-Columbia flight rules that killed a planned shuttle-servicing mission to Hubble, marks another step in the evolution of robot-partners for human space explorers. "Hubble has always been a pathfider for this agency," says Mike Weiss. Hubble deputy program manager technical. "When the space station was flown and assembled, Hubble was the pathfinder. not just for modularity, but for operations, for assembly techniques. Exploration is the next step. Things we're going to do on Hubble are going to be applied to exploration. It's not just putting a robot in space. It's operating a robot in space. It's adapting that robot to what needs to be done the next time you're up there."

Modification of gDNA extraction from soil for PCR designed for the routine examination of soil samples contaminated with Toxocara spp. eggs.

PubMed

Borecka, A; Gawor, J

2008-06-01

A modification of gDNA extraction was developed for the polymerase chain reaction (PCR) technique, intended for the detection and differentiation of Toxocara spp. eggs in soil or sediments. Sand samples from sandpits confirmed as being contaminated with Toxocara spp. eggs by the flotation technique were analysed by PCR. The use of proteinase K made it possible to obtain genomic DNA from the sample without needing to isolate eggs using flotation or to inactivate PCR inhibitors present in the sand. Specific primers in the PCR reaction allowed discrimination between T. canis and T. cati eggs. The modification simplified the procedure, thanks to eliminating the step of gDNA isolation from eggs, which is both laborious and difficult.

Constraint Maintenance with Preferences and Underlying Flexible Solution

NASA Technical Reports Server (NTRS)

Bresina, John; Jonsson, Ari; Morris, Paul; Rajan, Kanna

2003-01-01

This paper describes an aspect of the constraint reasoning mechanism. that is part of a ground planning system slated to be used for the Mars Exploration Rovers mission, where two rovers are scheduled to land on Mars in January of 2003. The planning system combines manual planning software from JPL with an automatic planning/scheduling system from NASA Ames Research Center, and is designed to be used in a mixed-initiative mode. Among other things, this means that after a plan has been produced, the human operator can perform extensive modifications under the supervision of the automated. system. For each modification to an activity, the automated system must adjust other activities as needed to ensure that constraints continue to be satisfied. Thus, the system must accommodate change in an interactive setting. Performance is of critical importance for interactive use. This is achieved by maintaining an underlying flexible solution to the temporal constraints, while the system presents a fixed schedule to the user. Adjustments are then a matter of constraint propagation rather than completely re-solving the problem. However, this begs the important question of which fixed schedule (among the ones sanctioned by the underlying flexible solution) should be presented to the user.Our approach uses least-change and other preferences as a prism through which the user views the flexible solution.

NOTE: Reducing the number of segments in unidirectional MLC segmentations

NASA Astrophysics Data System (ADS)

Mellado, X.; Cruz, S.; Artacho, J. M.; Canellas, M.

2010-02-01

In intensity-modulated radiation therapy (IMRT), fluence matrices obtained from a treatment planning system are usually delivered by a linear accelerator equipped with a multileaf collimator (MLC). A segmentation method is needed for decomposing these fluence matrices into segments suitable for the MLC, and the number of segments used is an important factor for treatment time. In this work, an algorithm for reduction of the number of segments (NS) is presented for unidirectional segmentations, where there is no backtracking of the MLC leaves. It uses a geometrical representation of the segmentation output for searching the key values in a fluence matrix that complicate its decomposition. The NS reduction is achieved by performing minor modifications in these values, under the conditions of avoiding substantial modifications of the dose-volume histogram, and does not increase in average the total number of monitor units delivered. The proposed method was tested using two clinical cases planned with the PCRT 3D® treatment planning system.

Microneedles as the technique of drug delivery enhancement in diverse organs and tissues.

PubMed

Rzhevskiy, Alexey S; Singh, Thakur Raghu Raj; Donnelly, Ryan F; Anissimov, Yuri G

2018-01-28

Microneedles is the technique of drug delivery enhancement, which was primarily designed for facilitating percutaneous drug delivery. Started from the development of simple solid microneedles, providing microporation of stratum corneum and therefore enhancement of topical drug delivery, for two decades the technique has progressed in various modifications such as hollow, coated, dissolving and hydrogel forming microneedles. In their turn, the modifications have resulted in new mechanisms of drug delivery enhancement and followed by the expansion of applicability range in terms of targeted tissues and organs. Thus, in addition to percutaneous drug delivery, microneedles have been considered as an efficient technique facilitating ocular, oral mucosal, gastrointestinal, ungual and vaginal drug administration. It is anticipated that the technique of microneedle-assisted drug delivery will soon become relevant for majority of organs and tissues. Copyright © 2017 Elsevier B.V. All rights reserved.

Application of modified dynamic conformal arc (MDCA) technique on liver stereotactic body radiation therapy (SBRT) planning following RTOG 0438 guideline

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Chengyu, E-mail: shicy1974@yahoo.com; Chen, Yong; Fang, Deborah

2015-04-01

Liver stereotactic body radiation therapy (SBRT) is a feasible treatment method for the nonoperable, patient with early-stage liver cancer. Treatment planning for the SBRT is very important and has to consider the simulation accuracy, planning time, treatment efficiency effects etc. The modified dynamic conformal arc (MDCA) technique is a 3-dimensional conformal arc planning method, which has been proposed for liver SBRT planning at our center. In this study, we compared the MDCA technique with the RapidArc technique in terms of planning target volume (PTV) coverage and sparing of organs at risk (OARs). The results show that the MDCA technique hasmore » comparable plan quality to RapidArc considering PTV coverage, hot spots, heterogeneity index, and effective liver volume. For the 5 PTVs studied among 4 patients, the MDCA plan, when compared with the RapidArc plan, showed 9% more hot spots, more heterogeneity effect, more sparing of OARs, and lower liver effective volume. The monitor unit (MU) number for the MDCA plan is much lower than for the RapidArc plans. The MDCA plan has the advantages of less planning time, no-collision treatment, and a lower MU number.« less

A Craniomaxillofacial Surgical Assistance Workstation for Enhanced Single-Stage Reconstruction Using Patient-Specific Implants.

PubMed

Murphy, Ryan J; Liacouras, Peter C; Grant, Gerald T; Wolfe, Kevin C; Armand, Mehran; Gordon, Chad R

2016-11-01

Craniomaxillofacial reconstruction with patient-specific, customized craniofacial implants (CCIs) is ideal for skeletal defects involving areas of aesthetic concern-the non-weight-bearing facial skeleton, temporal skull, and/or frontal-forehead region. Results to date are superior to a variety of "off-the-shelf" materials, but require a protocol computed tomography scan and preexisting defect for computer-assisted design/computer-assisted manufacturing of the CCI. The authors developed a craniomaxillofacial surgical assistance workstation to address these challenges and intraoperatively guide CCI modification for an unknown defect size/shape. First, the surgeon designed an oversized CCI based on his/her surgical plan. Intraoperatively, the surgeon resected the bone and digitized the resection using a navigation pointer. Next, a projector displayed the limits of the craniofacial bone defect onto the prefabricated, oversized CCI for the size modification process; the surgeon followed the projected trace to modify the implant. A cadaveric study compared the standard technique (n = 1) to the experimental technique (n = 5) using surgical time and implant fit. The technology reduced the time and effort needed to resize the oversized CCI by an order of magnitude as compared with the standard manual resizing process. Implant fit was consistently better for the computer-assisted case compared with the control by at least 30%, requiring only 5.17 minutes in the computer-assisted cases compared with 35 minutes for the control. This approach demonstrated improvement in surgical time and accuracy of CCI-based craniomaxillofacial reconstruction compared with previously reported methods. The craniomaxillofacial surgical assistance workstation will provide craniofacial surgeons a computer-assisted technology for effective and efficient single-stage reconstruction when exact craniofacial bone defect sizes are unknown.

A high rate of tibial plateau fractures after early experience with patient-specific instrumentation for unicompartmental knee arthroplasties.

PubMed

Leenders, A M; Schotanus, M G M; Wind, R J P; Borghans, R A P; Kort, N P

2018-04-30

Patient-specific instrumentation (PSI) for unicompartmental knee arthroplasty (UKA) has been available for a few years. However, limited literature is available on this subject. Hence, the aim of this cohort study is to evaluate the 2 years' results of our first experiences with the use of PSI in UKA. It is hypothesised that there is no advantage in rate of adverse events and in radiological and functional outcomes in comparison to literature on the conventional method. This cohort included 129 knees of 122 patients, operated by one surgeon. Outcome measures were the rate of adverse events (AEs); implant position as determined on radiographs; the accuracy of the default and approved planning of the implant sizes and the patient-reported outcome measures (PROMs) preoperatively, and at 3, 12 and 24 months, postoperatively. A total of 6 (4.9%) AEs were observed in this study, with 4 (3.3%) tibial fractures being the main complication. The mean postoperative biomechanical axis was 176.4° and in the majority of cases, the radiographic criteria, as determined by the manufacturer, were met. The tibial component showed 20 (16.4%) outliers in the sagittal and 3 (2.5%) outliers in the frontal plane. There were no outliers of the femoral component. For the femoral and tibial components, respectively, in 125 (96.9%) and 79 (61.7%) cases, there was an agreement between approved planning and implanted component size. All PROMs improved significantly after surgery. Tibial fracture was the most common AE, probably related to the transition from cemented to uncemented UKA. Perioperative modifications to the surgical technique were made in order to prevent this AE. Improvements should be made to the operation technique of the uncemented tibial plateau to obtain an adequate placement and at the same time reduce the risk for tibial fracture. The PSI technique was a reliable tool for the placement of the femoral component. Functional outcome was in line with literature on the conventional method. It is strongly recommended that the surgeon approves every preoperative plan, in order to optimise the accuracy during the PSI surgery. III.

Modifications to give HOPE/MDC 2.0 the capability to solve for or consider vent forces: Mission planning, mission analysis, and software formulation

NASA Technical Reports Server (NTRS)

Zyla, L. V.

1979-01-01

The modifications are described as necessary to give the Houston Operations Predictor/Estimator (HOPE) program the capability to solve for or consider vent forces for orbit determination. The model implemented in solving for vent forces is described along with the integrator problems encountered. A summary derivation of the mathematical principles applicable to solve/consider methodology is provided.

Dosimetric comparison of helical tomotherapy, RapidArc, and a novel IMRT & Arc technique for esophageal carcinoma.

PubMed

Martin, Spencer; Chen, Jeff Z; Rashid Dar, A; Yartsev, Slav

2011-12-01

To compare radiotherapy treatment plans for mid- and distal-esophageal cancer with primary involvement of the gastroesophageal (GE) junction using a novel IMRT & Arc technique (IMRT & Arc), helical tomotherapy (HT), and RapidArc (RA1 and RA2). Eight patients treated on HT for locally advanced esophageal cancer with radical intent were re-planned for RA and IMRT&Arc. RA plans employed single and double arcs (RA1 and RA2, respectively), while IMRT&Arc plans had four fixed-gantry IMRT fields and a conformal arc. Dose-volume histogram statistics, dose uniformity, and dose homogeneity were analyzed to compare treatment plans. RA2 plans showed significant improvement over RA1 plans in terms of OAR dose and PTV dose uniformity and homogeneity. HT plan provided best dose uniformity (p=0.001) and dose homogeneity (p=0.002) to planning target volume (PTV), while IMRT&Arc and RA2 plans gave lowest dose to lungs among four radiotherapy techniques with acceptable PTV dose coverage. Mean V(10) of the lungs was significantly reduced by the RA2 plans compared to IMRT&Arc (40.3%, p=0.001) and HT (66.2%, p<0.001) techniques. Mean V(15) of the lungs for the RA2 plans also showed significant improvement over the IMRT&Arc (25.2%, p=0.042) and HT (34.8%, p=0.027) techniques. These improvements came at the cost of higher doses to the heart volume compared to HT and IMRT&Arc techniques. Mean lung dose (MLD) for the IMRT&Arc technique (21.2 ± 5.0% of prescription dose) was significantly reduced compared to HT (26.3%, p=0.004), RA1 (23.3%, p=0.028), and RA2 (23.2%, p=0.017) techniques. The IMRT&Arc technique is a good option for treating esophageal cancer with thoracic involvement. It achieved optimal low dose to the lungs and heart with acceptable PTV coverage. HT is a good option for treating esophageal cancer with little thoracic involvement as it achieves superior dose conformality and uniformity. The RA2 technique provided for improved treatment plans using additional arcs with low doses to the lungs at the cost of increased heart dose. Plan quality could still be improved through the use of additional arcs. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Multimodal system planning technique : an analytical approach to peak period operation

DOT National Transportation Integrated Search

1995-11-01

The multimodal system planning technique described in this report is an improvement of the methodology used in the Dallas System Planning Study. The technique includes a spreadsheet-based process to identify the costs of congestion, construction, and...

Psychodrama Techniques for Inservice Teacher Training

ERIC Educational Resources Information Center

Kohut, Sylvester, Jr.

1976-01-01

By using psychodrama techniques in inservice programming, improvement in communication among members of the school community occurs. With modification the psychodrama approach can be used with inservice teachers and administrators to improve self-realization and communication. A program using psychodrama techniques is described in the article.…

12 CFR 944.6 - Bank community support programs.

Code of Federal Regulations, 2010 CFR

2010-01-01

... modification, which shall require the Bank to: (i) Conduct market research in the Bank's district; (ii... and implementing its Targeted Community Lending Plan; and (iv) Establish quantitative targeted...

12 CFR 1290.6 - Bank community support programs.

Code of Federal Regulations, 2014 CFR

2014-01-01

... to modification, which shall require the Bank to—(i) Conduct market research in the Bank's district... and implementing its Targeted Community Lending Plan; and (iv) Establish quantitative targeted...

76 FR 38747 - Review of New Sources and Modifications in Indian Country

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-01

...The EPA is finalizing a Federal Implementation Plan (FIP) under the Clean Air Act (CAA or Act) for Indian country. The FIP includes two New Source Review (NSR) regulations for the protection of air resources in Indian country. The first rule applies to new and modified minor stationary sources (minor sources) and to minor modifications at existing major stationary sources (major sources) throughout Indian country. The second rule (nonattainment major NSR rule) applies to new and modified major sources in areas of Indian country that are designated as not attaining the National Ambient Air Quality Standards (NAAQS). These rules will be implemented by EPA or a delegate Tribal agency assisting EPA with administration of the rules, until replaced by an EPA-approved implementation plan.

Planning comparison between intensity modulated radiation therapy and intensity modulated proton therapy in a case of head and neck cancer

NASA Astrophysics Data System (ADS)

Nguyen, T. T. C.; Nguyen, B. T.; Mai, N. V.

2018-03-01

In this work, we made the comparison between IMRT plan and IMPT plan for a head and neck case. We used Prowess Panther to perform IMRT plan and LAP- CERR for IMPT plan. The result showed that IMPT plan had better coverage than IMRT plan. In the IMRT plan, normal structures received higher dose with higher volume. Especially, the maximum dose of spinal cord is 31.5 Gy (RBE) using IMRT technique compared to 13.5 Gy (RBE) using IMPT technique. These results showed that IMPT is beneficial for head and neck cancer compared to IMRT technique.

Assessing a Critical Aspect of Construct Continuity when Test Specifications Change or Test Forms Deviate from Specifications

ERIC Educational Resources Information Center

Liu, Jinghua; Dorans, Neil J.

2013-01-01

We make a distinction between two types of test changes: inevitable deviations from specifications versus planned modifications of specifications. We describe how score equity assessment (SEA) can be used as a tool to assess a critical aspect of construct continuity, the equivalence of scores, whenever planned changes are introduced to testing…

24 CFR 5.655 - Section 8 project-based assistance programs: Owner preferences in selection for a project or unit.

Code of Federal Regulations, 2013 CFR

2013-04-01

... in the Affirmative Fair Housing Marketing plan (in accordance with § 108.25 of this title) as a... jurisdiction in which the project is located; (C) Modification of the Affirmative Fair Housing Marketing Plan... with a specific disability. (4) Preference for victims of domestic violence. The owner should consider...

24 CFR 5.655 - Section 8 project-based assistance programs: Owner preferences in selection for a project or unit.

Code of Federal Regulations, 2011 CFR

2011-04-01

... in the Affirmative Fair Housing Marketing plan (in accordance with § 108.25 of this title) as a... jurisdiction in which the project is located; (C) Modification of the Affirmative Fair Housing Marketing Plan... with a specific disability. (4) Preference for victims of domestic violence. The owner should consider...

24 CFR 5.655 - Section 8 project-based assistance programs: Owner preferences in selection for a project or unit.

Code of Federal Regulations, 2010 CFR

2010-04-01

... in the Affirmative Fair Housing Marketing plan (in accordance with § 108.25 of this title) as a... jurisdiction in which the project is located; (C) Modification of the Affirmative Fair Housing Marketing Plan... with a specific disability. (4) Preference for victims of domestic violence. The owner should consider...

24 CFR 5.655 - Section 8 project-based assistance programs: Owner preferences in selection for a project or unit.

Code of Federal Regulations, 2014 CFR

2014-04-01

... in the Affirmative Fair Housing Marketing plan (in accordance with § 108.25 of this title) as a... jurisdiction in which the project is located; (C) Modification of the Affirmative Fair Housing Marketing Plan... with a specific disability. (4) Preference for victims of domestic violence. The owner should consider...

24 CFR 5.655 - Section 8 project-based assistance programs: Owner preferences in selection for a project or unit.

Code of Federal Regulations, 2012 CFR

2012-04-01

... in the Affirmative Fair Housing Marketing plan (in accordance with § 108.25 of this title) as a... jurisdiction in which the project is located; (C) Modification of the Affirmative Fair Housing Marketing Plan... with a specific disability. (4) Preference for victims of domestic violence. The owner should consider...

Elementary Teachers' Ideas about, Planning for and Implementation of Learner-Directed and Teacher-Directed Inquiry: A Mixed Methods Study

ERIC Educational Resources Information Center

Biggers, Mandy Sue

2013-01-01

Using a framework for variations of classroom inquiry (National Research Council [NRC], 2000, p. 29), this study explored 40 inservice elementary teachers' planning, modification, and enactment of kit-based science curriculum materials. As part of the study, a new observation protocol was modified from an existing protocol (Practices of…

Surface modification effects on defect-related photoluminescence in colloidal CdS quantum dots.

PubMed

Lee, TaeGi; Shimura, Kunio; Kim, DaeGwi

2018-05-03

We investigated the effects of surface modification on the defect-related photoluminescence (PL) band in colloidal CdS quantum dots (QDs). A size-selective photoetching process and a surface modification technique with a Cd(OH)2 layer enabled the preparation of size-controlled CdS QDs with high PL efficiency. The Stokes shift of the defect-related PL band before and after the surface modification was ∼1.0 eV and ∼0.63 eV, respectively. This difference in the Stokes shifts suggests that the origin of the defect-related PL band was changed by the surface modification. Analysis by X-ray photoelectron spectroscopy revealed that the surface of the CdS QDs before and after the surface modification was S rich and Cd rich, respectively. These results suggest that Cd-vacancy acceptors and S-vacancy donors affect PL processes in CdS QDs before and after the surface modification, respectively.

Mapping Base Modifications in DNA by Transverse-Current Sequencing

NASA Astrophysics Data System (ADS)

Alvarez, Jose R.; Skachkov, Dmitry; Massey, Steven E.; Kalitsov, Alan; Velev, Julian P.

2018-02-01

Sequencing DNA modifications and lesions, such as methylation of cytosine and oxidation of guanine, is even more important and challenging than sequencing the genome itself. The traditional methods for detecting DNA modifications are either insensitive to these modifications or require additional processing steps to identify a particular type of modification. Transverse-current sequencing in nanopores can potentially identify the canonical bases and base modifications in the same run. In this work, we demonstrate that the most common DNA epigenetic modifications and lesions can be detected with any predefined accuracy based on their tunneling current signature. Our results are based on simulations of the nanopore tunneling current through DNA molecules, calculated using nonequilibrium electron-transport methodology within an effective multiorbital model derived from first-principles calculations, followed by a base-calling algorithm accounting for neighbor current-current correlations. This methodology can be integrated with existing experimental techniques to improve base-calling fidelity.

AN ANALYSIS OF THE INFLUENCE OF ANNUAL THERMAL VARIABLES ON THE OCCURRENCE OF WARM WATER FISHES

EPA Science Inventory

A potential effect of climate change is modification of the geographic distribution of fish species. To predict this modification it is necessary to estimate temperature tolerances of fishes and then relate these tolerances to the changing environment. This technique will allow...

Changing Attitudes Through Behavior Modification.

ERIC Educational Resources Information Center

Whipple, W. Scott

This article describes the philosophy and methods used by the staff at the Granite Alternative School in changing student attitudes through behavior modification. The students involved all have a failure syndrome or low self-image, and are dropouts from traditional high schools. Among the techniques used are: (1) reinforcing good behavior (praise…

76 FR 32929 - Western Pacific Pelagic Fisheries; American Samoa Longline Gear Modifications To Reduce Turtle...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-07

... Modifications To Reduce Turtle Interactions AGENCY: National Marine Fisheries Service (NMFS), National Oceanic... Pacific green sea turtles. DATES: Comments on the proposed rule must be received by July 22, 2011... sea turtles, seabirds, and marine mammals. Fishermen must use specific equipment and techniques for...

Event- and Time-Driven Techniques Using Parallel CPU-GPU Co-processing for Spiking Neural Networks

PubMed Central

Naveros, Francisco; Garrido, Jesus A.; Carrillo, Richard R.; Ros, Eduardo; Luque, Niceto R.

2017-01-01

Modeling and simulating the neural structures which make up our central neural system is instrumental for deciphering the computational neural cues beneath. Higher levels of biological plausibility usually impose higher levels of complexity in mathematical modeling, from neural to behavioral levels. This paper focuses on overcoming the simulation problems (accuracy and performance) derived from using higher levels of mathematical complexity at a neural level. This study proposes different techniques for simulating neural models that hold incremental levels of mathematical complexity: leaky integrate-and-fire (LIF), adaptive exponential integrate-and-fire (AdEx), and Hodgkin-Huxley (HH) neural models (ranged from low to high neural complexity). The studied techniques are classified into two main families depending on how the neural-model dynamic evaluation is computed: the event-driven or the time-driven families. Whilst event-driven techniques pre-compile and store the neural dynamics within look-up tables, time-driven techniques compute the neural dynamics iteratively during the simulation time. We propose two modifications for the event-driven family: a look-up table recombination to better cope with the incremental neural complexity together with a better handling of the synchronous input activity. Regarding the time-driven family, we propose a modification in computing the neural dynamics: the bi-fixed-step integration method. This method automatically adjusts the simulation step size to better cope with the stiffness of the neural model dynamics running in CPU platforms. One version of this method is also implemented for hybrid CPU-GPU platforms. Finally, we analyze how the performance and accuracy of these modifications evolve with increasing levels of neural complexity. We also demonstrate how the proposed modifications which constitute the main contribution of this study systematically outperform the traditional event- and time-driven techniques under increasing levels of neural complexity. PMID:28223930

Prevention of Unilateral Pulmonary Edema Complicating Robotic Mitral Valve Operations.

PubMed

Moss, Emmanuel; Halkos, Michael E; Binongo, Jose N; Murphy, Douglas A

2017-01-01

Unilateral pulmonary edema (UPE) has been reported after mitral operations performed through the right side of the chest. The clinical presentation is compatible with an ischemia-reperfusion injury. This report describes modifications to robotic mitral valve operations that were designed to reduce UPE. We reviewed 15 patients with UPE after robotic mitral valve operations from 2006 through 2012. Technique modifications to reduce right lung ischemia were used from 2013 through June 2015. Modifications included alterations in patient position, ventilation, and perfusion factors. The incidence of UPE before and after modifications was determined, as was perfusion factors and outcomes in a higher-risk patient subgroup with pulmonary hypertension and prolonged bypass procedures. The incidence of UPE was 1.4% (n = 15) in 1,059 consecutive robotic mitral valve procedures using the standard technique and 0.0% in 435 consecutive procedures using the modified technique (p < 0.02). All patients with UPE had pulmonary hypertension and bypass times of greater than 120 minutes. Patients in the higher-risk subgroup had significantly lower systemic temperature (31°C [range, 30°-32°C] versus 34°C [range, 33°-34°C]; p < 0.01) and higher mean perfusion pressure (67mm Hg [range 62-72 mm Hg] versus 54 mm Hg [range, 52-57 mm Hg]; p < 0.01) on bypass using the modified technique. The incidence of UPE in higher-risk patients was significantly reduced using the modified technique (0% versus 5.6%; p < 0.01) without any increase in overall morbidity or mortality. The incidence of UPE in patients undergoing robotic mitral valve operations has been significantly reduced using a modified technique, without increasing the perioperative complication rate. Further work is necessary to validate this protocol and understand the pathophysiology of postoperative UPE. Copyright © 2017 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Materials research at CMAM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zucchiatti, Alessandro

2013-07-18

The Centro de Micro Analisis de Materiales (CMAM) is a research centre of the Universidad Autonoma de Madrid dedicated to the modification and analysis of materials using ion beam techniques. The infrastructure, based on a HVEE 5MV tandem accelerator, provided with a coaxial Cockcroft Walton charging system, is fully open to research groups of the UAM, to other public research institutions and to private enterprises. The CMAM research covers a few important lines such as advanced materials, surface science, biomedical materials, cultural heritage, materials for energy production. The Centre gives as well support to university teaching and technical training. Amore » detail description of the research infrastructures and their use statistics will be given. Some of the main research results will be presented to show the progress of research in the Centre in the past few years and to motivate the strategic plans for the forthcoming.« less

Interstitial ablation and imaging of soft tissue using miniaturized ultrasound arrays

NASA Astrophysics Data System (ADS)

Makin, Inder R. S.; Gallagher, Laura A.; Mast, T. Douglas; Runk, Megan M.; Faidi, Waseem; Barthe, Peter G.; Slayton, Michael H.

2004-05-01

A potential alternative to extracorporeal, noninvasive HIFU therapy is minimally invasive, interstitial ultrasound ablation that can be performed laparoscopically or percutaneously. Research in this area at Guided Therapy Systems and Ethicon Endo-Surgery has included development of miniaturized (~3 mm diameter) linear ultrasound arrays capable of high power for bulk tissue ablation as well as broad bandwidth for imaging. An integrated control system allows therapy planning and automated treatment guided by real-time interstitial B-scan imaging. Image quality, challenging because of limited probe dimensions and channel count, is aided by signal processing techniques that improve image definition and contrast. Simulations of ultrasonic heat deposition, bio-heat transfer, and tissue modification provide understanding and guidance for development of treatment strategies. Results from in vitro and in vivo ablation experiments, together with corresponding simulations, will be described. Using methods of rotational scanning, this approach is shown to be capable of clinically relevant ablation rates and volumes.

Development and Testing of a High Stability Engine Control (HISTEC) System

NASA Technical Reports Server (NTRS)

Orme, John S.; DeLaat, John C.; Southwick, Robert D.; Gallops, George W.; Doane, Paul M.

1998-01-01

Flight tests were recently completed to demonstrate an inlet-distortion-tolerant engine control system. These flight tests were part of NASA's High Stability Engine Control (HISTEC) program. The objective of the HISTEC program was to design, develop, and flight demonstrate an advanced integrated engine control system that uses measurement-based, real-time estimates of inlet airflow distortion to enhance engine stability. With improved stability and tolerance of inlet airflow distortion, future engine designs may benefit from a reduction in design stall-margin requirements and enhanced reliability, with a corresponding increase in performance and decrease in fuel consumption. This paper describes the HISTEC methodology, presents an aircraft test bed description (including HISTEC-specific modifications) and verification and validation ground tests. Additionally, flight test safety considerations, test plan and technique design and approach, and flight operations are addressed. Some illustrative results are presented to demonstrate the type of analysis and results produced from the flight test program.

Placement of empty catheters for an HDR-emulating LDR prostate brachytherapy technique: comparison to standard intraoperative planning.

PubMed

Niedermayr, Thomas R; Nguyen, Paul L; Murciano-Goroff, Yonina R; Kovtun, Konstantin A; Neubauer Sugar, Emily; Cail, Daniel W; O'Farrell, Desmond A; Hansen, Jorgen L; Cormack, Robert A; Buzurovic, Ivan; Wolfsberger, Luciant T; O'Leary, Michael P; Steele, Graeme S; Devlin, Philip M; Orio, Peter F

2014-01-01

We sought to determine whether placing empty catheters within the prostate and then inverse planning iodine-125 seed locations within those catheters (High Dose Rate-Emulating Low Dose Rate Prostate Brachytherapy [HELP] technique) would improve concordance between planned and achieved dosimetry compared with a standard intraoperative technique. We examined 30 consecutive low dose rate prostate cases performed by standard intraoperative technique of planning followed by needle placement/seed deposition and compared them to 30 consecutive low dose rate prostate cases performed by the HELP technique. The primary endpoint was concordance between planned percentage of the clinical target volume that receives at least 100% of the prescribed dose/dose that covers 90% of the volume of the clinical target volume (V100/D90) and the actual V100/D90 achieved at Postoperative Day 1. The HELP technique had superior concordance between the planned target dosimetry and what was actually achieved at Day 1 and Day 30. Specifically, target D90 at Day 1 was on average 33.7 Gy less than planned for the standard intraoperative technique but was only 10.5 Gy less than planned for the HELP technique (p < 0.001). Day 30 values were 16.6 Gy less vs. 2.2 Gy more than planned, respectively (p = 0.028). Day 1 target V100 was 6.3% less than planned with standard vs. 2.8% less for HELP (p < 0.001). There was no significant difference between the urethral and rectal concordance (all p > 0.05). Placing empty needles first and optimizing the plan to the known positions of the needles resulted in improved concordance between the planned and the achieved dosimetry to the target, possibly because of elimination of errors in needle placement. Copyright © 2014 American Brachytherapy Society. Published by Elsevier Inc. All rights reserved.

College Preparation for Students with Learning Disabilities: A Curriculum Approach.

ERIC Educational Resources Information Center

Whinnery, Keith W.

1992-01-01

A college preparation curriculum relevant to the needs of students with learning disabilities is presented, focusing on early planning, instructional modifications, strategy instruction, and support services. (JDD)

Chemical methods for encoding and decoding of posttranslational modifications

PubMed Central

Chuh, Kelly N.; Batt, Anna R.; Pratt, Matthew R.

2016-01-01

A large array of posttranslational modifications can dramatically change the properties of proteins and influence different aspects of their biological function such as enzymatic activity, binding interactions, and proteostasis. Despite the significant knowledge that has been gained about the function of posttranslational modifications using traditional biological techniques, the analysis of the site-specific effects of a particular modification, the identification of the full compliment of modified proteins in the proteome, and the detection of new types of modifications remains challenging. Over the years, chemical methods have contributed significantly in both of these areas of research. This review highlights several posttranslational modifications where chemistry-based approaches have made significant contributions to our ability to both prepare homogeneously modified proteins and identify and characterize particular modifications in complex biological settings. As the number and chemical diversity of documented posttranslational modifications continues to rise, we believe that chemical strategies will be essential to advance the field in years to come. PMID:26933738

Intraoperative modification of Pitanguy technique of reduction mammaplasty for elevation of the nipple-areola complex in case of severe breast ptosis.

PubMed

Foustanos, Andreas; Panagiotopoulos, Konstantinos; Skouras, George

2011-02-01

The Pitanguy method of reduction mammaplasty has been shown to be an anatomically safe technique in the management of the ptotic breast. However, the technique, as first described, cannot be applied in gigantomastia or severe breast ptosis cases or cases of dense parenchyma of the breast. The senior surgeon suggested an intraoperative modification of the Pitanguy method of reduction mammaplasty to make it applicable for such cases. A retrospective study of 122 patients with severe breast ptosis (70), gigantomastia (45), or dense breast parenchyma (7) who underwent a modification of the Pitanguy method was performed. The current procedure involves all the operating steps of the superior pedicle technique as described by Pitanguy, from the marking technique to the keel resection of the breast. If the nipple-areola complex is elevated inadequately, the surgeon can use the senior surgeon's modification to elevate the complex to the desired height. This modification consists of dissecting the upper pole of the breast vertically to the fascia of the pectoralis major muscle and laterally to the nipple-areola complex. The medial flap is then advanced superiorly, rotated 90°, and sutured to point A, while the lateral flap is placed below the medial one. This maneuver maximizes elevation of the nipple-areola complex to the desired height. The mean change in nipple position was 14 cm (range = 10-16 cm). The mean weight reduction of each breast was 900 g (range = 700-1300 g). The follow-up included 119 patients and the follow-up period ranged from 1 to 3 years (mean follow-up = 2 years). Three patients were operated on less than 3 months ago and were not involved in this study. All patients gained natural shaped breasts and they were pleased with the results. Serious complications, including flap necrosis, were avoided since caution was used to preserve the internal mammary perforators while performing this method. This technique provides a versatile, well-vascularized pedicle that allows elevation of the nipple-areola complex at the desired height in cases of severe breast ptosis, gigantomastia, or dense breast parenchyma.

Retention Forces between Titanium and Zirconia Components of Two-Part Implant Abutments with Different Techniques of Surface Modification.

PubMed

von Maltzahn, Nadine Freifrau; Holstermann, Jan; Kohorst, Philipp

2016-08-01

The adhesive connection between titanium base and zirconia coping of two-part abutments may be responsible for the failure rate. A high mechanical stability between both components is essential for the long-term success. The aim of the present in-vitro study was to evaluate the influence of different surface modification techniques and resin-based luting agents on the retention forces between titanium and zirconia components in two-part implant abutments. A total of 120 abutments with a titanium base bonded to a zirconia coping were investigated. Two different resin-based luting agents (Panavia F 2.0 and RelyX Unicem) and six different surface modifications were used to fix these components, resulting in 12 test groups (n = 10). The surface of the test specimens was mechanically pretreated with aluminium oxide blasting in combination with application of two surface activating primers (Alloy Primer, Clearfil Ceramic Primer) or a tribological conditioning (Rocatec), respectively. All specimens underwent 10,000 thermal cycles between 5°C and 55°C in a moist environment. A pull-off test was then conducted to determine retention forces between the titanium and zirconia components, and statistical analysis was performed (two-way anova). Finally, fracture surfaces were analyzed by light and scanning electron microscopy. No significant differences were found between Panavia F 2.0 and RelyX Unicem. However, the retention forces were significantly influenced by the surface modification technique used (p < 0.001). For both luting agents, the highest retention forces were found when adhesion surfaces of both the titanium bases and the zirconia copings were pretreated with aluminium oxide blasting, and with the application of Clearfil Ceramic Primer. Surface modification techniques crucially influence the retention forces between titanium and zirconia components in two-part implant abutments. All adhesion surfaces should be pretreated by sandblasting. Moreover, a phosphate-based primer serves to enhance long-term retention of the components. © 2015 Wiley Periodicals, Inc.

40 CFR 62.9631 - Identification of sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Landfill Gas Emissions from Existing Municipal Solid Waste Landfills (section 111(d) Plan) § 62.9631... landfills for which construction, reconstruction, or modification was commenced before May 30, 1991 and that...

28 CFR 2.106 - Youth Rehabilitation Act.

Code of Federal Regulations, 2010 CFR

2010-07-01

... hearing examiner. Any proposed modifications to the plan shall be discussed at the hearing, although..., the parolee's prior criminal history, the offense behavior that led to his conviction, record of drug...

12 CFR 1290.6 - Bank community support programs.

Code of Federal Regulations, 2011 CFR

2011-01-01

... modification, which shall require the Bank to—(i) Conduct market research in the Bank's district; (ii) Describe... implementing its Targeted Community Lending Plan; and (iv) Establish quantitative targeted community lending...

12 CFR 1290.6 - Bank community support programs.

Code of Federal Regulations, 2013 CFR

2013-01-01

... modification, which shall require the Bank to—(i) Conduct market research in the Bank's district; (ii) Describe... implementing its Targeted Community Lending Plan; and (iv) Establish quantitative targeted community lending...

12 CFR 1290.6 - Bank community support programs.

Code of Federal Regulations, 2012 CFR

2012-01-01

... modification, which shall require the Bank to—(i) Conduct market research in the Bank's district; (ii) Describe... implementing its Targeted Community Lending Plan; and (iv) Establish quantitative targeted community lending...

38 CFR 36.4367 - Requirement of construction warranty.

Code of Federal Regulations, 2010 CFR

2010-07-01

... property has been completed in substantial conformity with the plans and specifications upon which the Secretary based the valuation of the property, including any modifications thereof, or changes or variations...

Accelerated Partial Breast Irradiation: What is Dosimetric Effect of Advanced Technology Approaches?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moran, Jean M.; Ben-David, Merav A.; Marsh, Robin B.

2009-09-01

Purpose: The present treatment planning study compared whole breast radiotherapy (WBRT) to accelerated partial breast irradiation (APBI) for different external beam techniques and geometries (e.g., free breathing [FB] and deep inspiration breath hold [DIBH]). Methods and Materials: After approval by our institutional review board, a treatment planning study was performed of 10 patients with left-sided Stage 0-I breast cancer enrolled in a Phase I-II study of APBI using intensity-modulated radiotherapy (IMRT). After lumpectomy, patients underwent planning computed tomography scans during FB and using an active breathing control device at DIBH. For the FB geometry, standard WBRT and three-dimensional conformal radiotherapymore » (3D-CRT) APBI plans were created. For the DIBH geometry with active breathing control, WBRT, 3D-CRT, and IMRT APBI plans were created. Results: All APBI techniques had excellent planning target volume coverage. The maximal planning target volume dose was reduced from 116% of the prescription dose to 108% with the IMRT(DIBH) APBI plan. The maximal heart dose was >30 Gy for the WBRT techniques, 8.2 Gy for 3D-CRT(FB), and <5.0 Gy for 3D-CRT(DIBH) and IMRT(DIBH) techniques. The mean left anterior descending artery dose was significantly reduced from 11.4 Gy with WBRT(FB) to 4.2 with WBRT(DIBH) and <2.0 Gy with all APBI techniques. Conclusion: Although planning target volume coverage was acceptable with all techniques, the plans using the DIBH geometry resulted in a marked reduction in the normal tissue dose compared with WBRT planned in the absence of cardiac blocking. Additional study is needed to determine whether these techniques result in clinical benefits.« less

Applying usability testing techniques to improve a health promotion website.

PubMed

Hinchliffe, Anetta; Mummery, W Kerry

2008-04-01

Use of the Internet for health promotion is increasing; however, the lack of published research regarding website usability suggests that health promotion websites are being developed without consultation with their users or formal evaluation. This study conducted usability testing of an existing health promotion website to inform modifications and to identify common usability themes that should be addressed by organisations developing or maintaining a health promotion website. A combination of qualitative and quantitative techniques were implemented during the usability testing sessions to gather data from users while completing tasks on the website. Techniques included performance measures (time taken), direct observation (participant observation) and subjective user preferences (questionnaire and interview). Improvements to the website were measured in terms of reduced problems reported, reduced time taken to complete tasks and increased subjective reports. Seven usability themes emerged from the data: design, feedback, format, instructions, navigation, terminology and learnability. This study demonstrates the application of usability testing to the design and modification of a health promotion website and illustrates the areas or themes that can be used as a framework for testing and modification.

From Ringmaster to Conductor: 10 Simple Techniques Can Turn an Unruly Class into a Productive One

ERIC Educational Resources Information Center

Kraft, Matthew A.

2010-01-01

Challenging classrooms can overwhelm a teacher. However, by using effective classroom management and behavior modification techniques, teachers can change challenging classrooms into productive ones. Classroom management techniques include using a relevant curriculum, establishing nonnegotiable rules, ensuring that students know what behavior is…

Glycobiology, how to sugar-coat an undergraduate advanced biochemistry laboratory.

PubMed

McReynolds, Katherine D

2006-09-01

A second semester biochemistry laboratory has been implemented as an independent projects course at California State University, Sacramento since 1999. To incorporate aspects of carbohydrate biochemistry, or glycobiology, into our curriculum, projects in lectin isolation and purification were undertaken over the course of two semesters. Through this modification in course content, this class now offers a diverse, hands-on treatment of not only standard protein purification techniques but also carbohydrate techniques, specifically the study of carbohydrate-protein interactions through hemagglutination assays, a novel commercial assay known as the Instant™Chek assay, and the generation and use of appropriate affinity chromatography matrices. Throughout the semester, the students are in charge of all aspects of their projects, from planning to execution and completion. Specific examples of student projects are highlighted such that the breadth of protein-carbohydrate chemistry pursued in a 15-week semester can be appreciated. The feedback of the course was very favorable, indicating that the students came away with skills necessary for them to be successful in their future careers. Most importantly, however, aspects of glycobiology have now been incorporated effectively into a mainstream undergraduate biochemistry laboratory class. Copyright © 2006 International Union of Biochemistry and Molecular Biology, Inc.

Scar modification. Techniques for revision and camouflage.

PubMed

Horswell, B B

1998-09-01

The surgery and management of scars is a protracted and staged process that includes preparation of the skin through hygienic measures, scar softening (if indicated) with steroids, massage and pressure dressings, skilled execution of the surgical plan, and thorough postoperative wound care. This process generally covers a 1-year period for the various stages mentioned. Many general host and local skin factors will directly affect the final revision result. The two most important indirect factors that the surgeon must endeavor to control are optimal patient preparation and cutaneous health, and patient compliance with, and an ability to carry out, those wound care measures that the surgeon prescribes. Keloid and burn contracture scars represent two entities that are complicated and challenging to treat owing to their abnormal morphophysiologic features. Management of these scars is prolonged, and the patient must understand that the ultimate result will usually be a compromise. New grafting techniques, such as cultured autodermal grafts, offer improved initial management of burn wounds that may subsequently optimize scar revision in these patients. Keloids, and to a lesser extent hypertrophic scars, require steroid injections, pressure treatment, careful surgery, and protracted wound support and pressure treatment (exceeding 6 months) after surgery.

Analysis of transport eco-efficiency scenarios to support sustainability assessment: a study on Dhaka City, Bangladesh.

PubMed

Iqbal, Asif; Allan, Andrew; Afroze, Shirina

2017-08-01

The study focused to assess the level of efficiency (of both emissions and service quality) that can be achieved for the transport system in Dhaka City, Bangladesh. The assessment technique attempted to quantify the extent of eco-efficiency achievable for the system modifications due to planning or strategy. The eco-efficiency analysis was facilitated with a detailed survey data on Dhaka City transport system, which was conducted for 9 months in 2012-2013. Line source modelling (CALINE4) was incorporated to estimate the on-road emission concentration. The eco-efficiency of the transport systems was assessed with the 'multi-criteria analysis' (MCA) technique that enabled the valuation of systems' qualitative and quantitative parameters. As per the analysis, driving indiscipline on road can alone promise about 47% reductions in emissions, which along with the number of private vehicles were the important stressors that restrict achieving eco-efficiency in Dhaka City. Detailed analysis of the transport system together with the potential transport system scenarios can offer a checklist to the policy makers enabling to identify the possible actions needed that can offer greater services to the dwellers against lesser emissions, which in turn can bring sustainability of the system.

Channeling techniques to study strains and defects in heterostructures and multi quantum wells

NASA Astrophysics Data System (ADS)

Pathak, A. P.; Dhamodaran, S.; Sathish, N.

2005-08-01

The importance and advantages of heterostructures and Quantum Wells (QWs) in device technology has made research challenging due to lack of direct techniques for their characterization. Particularly the characterization of strain and defects at the interfaces has become important due to their dominance in the electrical and optical properties of materials and devices. RBSiC has been used to study variety of defects in single crystalline materials, for nearly four decades now. Channeling based experiments play a crucial role in giving depth information of strain and defects. Ion beams are used for both material characterizations as well as for modifications. Hence it is also possible to monitor the modifications online, which are discussed in detail. In the present work, Swift Heavy Ion (SHI) modification of III-V semiconductor heterostnictures and MQWs and the results of subsequent strain measurements by RBSiC in initially strained as well as lattice matched systems are discussed. We find that the compressive strain decreases due to SHI irradiation and a tensile strain is induced in an initially lattice matched system. The incident ion fluence dependence of strain modifications in the heterostructures will also be discussed. The use of high energy channeling for better sensitivity of strain measurements in low mismatch materials will be discussed in detail. Wherever possible, a comparison of results with those obtained by other techniques like HRXRD is given.

Evaluation of three simple direct or indirect carbonyl detection methods for characterization of oxidative modifications of proteins.

PubMed

Vásquez-Garzón, Verónica R; Rouimi, Patrick; Jouanin, Isabelle; Waeg, Georg; Zarkovic, Neven; Villa-Treviño, Saul; Guéraud, Françoise

2012-05-01

Among disruptions induced by oxidative stress, modifications of proteins, particularly irreversible carbonylation, are associated with the development of several diseases, including cardiovascular diseases, neurodegenerative diseases, and cancer. Carbonylation of proteins can occur directly or indirectly through the adduction of lipid oxidation products. In this study, three classical and easy-to-perform techniques to detect direct or indirect carbonylation of proteins were compared. A model protein apomyoglobin and a complex mixture of rat liver cytosolic proteins were exposed to cumene hydroperoxide oxidation or adduction to the lipid peroxidation product 4-hydroxynonenal in order to test direct or indirect carbonylation, respectively. The technique using a specific anti-4-hydroxynonenal-histidine adduct antibody was effective to detect in vitro modification of model apomyoglobin and cytosolic proteins by 4-hydroxynonenal but not by direct carbonylation which was achieved by techniques using biotin-coupled hydrazide or dinitrophenylhydrazine derivatization of carbonyls. Sequential use of these methods enabled the detection of both direct and indirect carbonyl modification in proteins, although constitutively biotinylated proteins were detected by biotin-hydrazide. Although rather classical and efficient, methods for carbonyl detection on proteins in oxidative stress studies may be biased by some artifactual detections and complicated by proteins multimerizations. The use of more and more specific available antibodies is recommended to complete detection of lipid peroxidation product adducts on proteins.

Modification of the Nominal Group Activity for On-Line Instruction.

ERIC Educational Resources Information Center

Maulding, Wanda S.

This paper discusses how the Nominal Group Technique (NGT) can be adapted for use in online instruction. The four basic stages of the NGT (listing, recording, collating, and prioritizing) are described, and modifications for online delivery are detailed, including: (1) the instructor posts the Socratic question or problem to be posed; (2) students…

FLEXWAL: A computer program for predicting the wall modifications for two-dimensional, solid, adaptive-wall tunnels

NASA Technical Reports Server (NTRS)

Everhart, J. L.

1983-01-01

A program called FLEXWAL for calculating wall modifications for solid, adaptive-wall wind tunnels is presented. The method used is the iterative technique of NASA TP-2081 and is applicable to subsonic and transonic test conditions. The program usage, program listing, and a sample case are given.

Black Psychologists Discuss Behavior Modification.

ERIC Educational Resources Information Center

Bardo, Harold R.; And Others

The primary purpose of this paper is to discuss reasons why blacks should be concerned and actively involved with practices in behavior modification. The concern is that as these techniques are refined it becomes more important to be sure blacks should be involved at all levels of the application of these procedures when other blacks are subjects…

Environmental assessment of combustion modification controls for stationary internal combustion engines. Final report Sep 78-Jul 79

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lips, H.I.; Gotterba, J.A.; Lim, K.J.

1981-07-01

The report gives results of an environmental assessment of combustion modification techniques for stationary internal combustion engines, with respect to NOx control reduction effectiveness, operational impact, thermal efficiency impact, capital and annualized operating costs, and effects on emissions of pollutants other than NOx.

Test/QA plan for the verification testing of diesel exhaust catalysts, particulate filters and engine modification control technologies for highway and nonroad use diesel engines

EPA Science Inventory

This ETV test/QA plan for heavy-duty diesel engine testing at the Southwest Research Institute’s Department of Emissions Research (DER) describes how the Federal Test Procedure (FTP), as listed in 40 CFR Part 86 for highway engines and 40 CFR Part 89 for nonroad engines, will be ...

29 CFR 2550.408b-1 - General statutory exemption for loans to plan participants and beneficiaries who are parties in...

Code of Federal Regulations, 2011 CFR

2011-07-01

... administered for the exclusive purpose of providing benefits to participants and beneficiaries of the plan. (ii) For the purpose of this regulation, the term “loan” will include any renewal or modification of an... exclusive purpose requirements of sections 403(c) and 404(a). In effect, the entire transaction is viewed as...

29 CFR 2550.408b-1 - General statutory exemption for loans to plan participants and beneficiaries who are parties in...

Code of Federal Regulations, 2013 CFR

2013-07-01

... administered for the exclusive purpose of providing benefits to participants and beneficiaries of the plan. (ii) For the purpose of this regulation, the term “loan” will include any renewal or modification of an... exclusive purpose requirements of sections 403(c) and 404(a). In effect, the entire transaction is viewed as...

29 CFR 2550.408b-1 - General statutory exemption for loans to plan participants and beneficiaries who are parties in...

Code of Federal Regulations, 2012 CFR

2012-07-01

... administered for the exclusive purpose of providing benefits to participants and beneficiaries of the plan. (ii) For the purpose of this regulation, the term “loan” will include any renewal or modification of an... exclusive purpose requirements of sections 403(c) and 404(a). In effect, the entire transaction is viewed as...

29 CFR 2550.408b-1 - General statutory exemption for loans to plan participants and beneficiaries who are parties in...

Code of Federal Regulations, 2014 CFR

2014-07-01

... administered for the exclusive purpose of providing benefits to participants and beneficiaries of the plan. (ii) For the purpose of this regulation, the term “loan” will include any renewal or modification of an... exclusive purpose requirements of sections 403(c) and 404(a). In effect, the entire transaction is viewed as...

The Joint Staff Strategic Information Technology Plan

DTIC Science & Technology

1995-09-01

analyses or assessments. Gaming Division ( SAGD ) is responsible for: This element also addresses the modification of existing applications necessary to...Joint Military Net Assessment, and the Joint Strategic Planning System. SAGD Gaming Suite: SAGD’s mission has • undergone revision and expansion, As...situations using both gaming and analytical assessments. approaches. Table 3 gives characteristics of some of the types of applications that SAGD has • * 4

Preliminary design study of advanced composite blade and hub and nonmechanical control system for the tilt-rotor aircraft. Volume 2: Project planning data

NASA Technical Reports Server (NTRS)

1980-01-01

Project planning data for a rotor and control system procurement and testing program for modifications to the XV-15 tilt-rotor research demonstrator aircraft is presented. The design, fabrication, and installation of advanced composite blades compatible with the existing hub, an advanced composite hub, and a nonmechanical control system are required.

Incorporation of post-translational modified amino acids as an approach to increase both chemical and biological diversity of conotoxins and conopeptides.

PubMed

Espiritu, Michael J; Cabalteja, Chino C; Sugai, Christopher K; Bingham, Jon-Paul

2014-01-01

Bioactive peptides from Conus venom contain a natural abundance of post-translational modifications that affect their chemical diversity, structural stability, and neuroactive properties. These modifications have continually presented hurdles in their identification and characterization. Early endeavors in their analysis relied on classical biochemical techniques that have led to the progressive development and use of novel proteomic-based approaches. The critical importance of these post-translationally modified amino acids and their specific assignment cannot be understated, having impact on their folding, pharmacological selectivity, and potency. Such modifications at an amino acid level may also provide additional insight into the advancement of conopeptide drugs in the quest for precise pharmacological targeting. To achieve this end, a concerted effort between the classical and novel approaches is needed to completely elucidate the role of post-translational modifications in conopeptide structure and dynamics. This paper provides a reflection in the advancements observed in dealing with numerous and multiple post-translationally modified amino acids within conotoxins and conopeptides and provides a summary of the current techniques used in their identification.

Planning satellite communication services and spectrum-orbit utilization

NASA Technical Reports Server (NTRS)

Sawitz, P. H.

1982-01-01

The relationship between approaches to planning satellite communication services and spectrum-orbit utilization is considered, with emphasis on the fixed-satellite and the broadcasting-satellite services. It is noted that there are several possible approaches to planning space services, differing principally in the rigidity with which technical parameters are prescribed, in the time for which a plan remains in force, and in the procedures adopted for implementation and modifications. With some planning approaches, spectrum-orbit utilization is fixed at the time the plan is made. Others provide for greater flexibility by making it possible to postpone some decisions on technical parameters. In addition, the two political questions of what is equitable access and how it can be guaranteed in practice play an important role.

AAA and AXB algorithms for the treatment of nasopharyngeal carcinoma using IMRT and RapidArc techniques.

PubMed

Kamaleldin, Maha; Elsherbini, Nader A; Elshemey, Wael M

2017-09-27

The aim of this study is to evaluate the impact of anisotropic analytical algorithm (AAA) and 2 reporting systems (AXB-D m and AXB-D w ) of Acuros XB algorithm (AXB) on clinical plans of nasopharyngeal patients using intensity-modulated radiotherapy (IMRT) and RapidArc (RA) techniques. Six plans of different algorithm-technique combinations are performed for 10 patients to calculate dose-volume histogram (DVH) physical parameters for planning target volumes (PTVs) and organs at risk (OARs). The number of monitor units (MUs) and calculation time are also determined. Good coverage is reported for all algorithm-technique combination plans without exceeding the tolerance for OARs. Regardless of the algorithm, RA plans persistently reported higher D 2% values for PTV-70. All IMRT plans reported higher number of MUs (especially with AXB) than did RA plans. AAA-IMRT produced the minimum calculation time of all plans. Major differences between the investigated algorithm-technique combinations are reported only for the number of MUs and calculation time parameters. In terms of these 2 parameters, it is recommended to employ AXB in calculating RA plans and AAA in calculating IMRT plans to achieve minimum calculation times at reduced number of MUs. Copyright © 2017 American Association of Medical Dosimetrists. Published by Elsevier Inc. All rights reserved.

Periradicular Infiltration of the Cervical Spine: How New CT Scanner Techniques and Protocol Modifications Contribute to the Achievement of Low-Dose Interventions.

PubMed

Elsholtz, Fabian Henry Jürgen; Kamp, Julia Evi-Katrin; Vahldiek, Janis Lucas; Hamm, Bernd; Niehues, Stefan Markus

2018-06-18

 CT-guided periradicular infiltration of the cervical spine is an effective symptomatic treatment in patients with radiculopathy-associated pain syndromes. This study evaluates the robustness and safety of a low-dose protocol on a CT scanner with iterative reconstruction software.  A total of 183 patients who underwent periradicular infiltration therapy of the cervical spine were included in this study. 82 interventions were performed on a new CT scanner with a new intervention protocol using an iterative reconstruction algorithm. Spot scanning was implemented for planning and a basic low-dose setup of 80 kVp and 5 mAs was established during intermittent fluoroscopy. The comparison group included 101 prior interventions on a scanner without iterative reconstruction. The dose-length product (DLP), number of acquisitions, pain reduction on a numeric analog scale, and protocol changes to achieve a safe intervention were recorded.  The median DLP for the whole intervention was 24.3 mGy*cm in the comparison group and 1.8 mGy*cm in the study group. The median pain reduction was -3 in the study group and -2 in the comparison group. A 5 mAs increase in the tube current-time product was required in 5 patients of the study group.  Implementation of a new scanner and intervention protocol resulted in a 92.6 % dose reduction without a compromise in safety and pain relief. The dose needed here is more than 75 % lower than doses used for similar interventions in published studies. An increase of the tube current-time product was needed in only 6 % of interventions.   · The presented ultra-low-dose protocol allows for a significant dose reduction without compromising outcome.. · The protocol includes spot scanning for planning purposes and a basic setup of 80 kVp and 5 mAs.. · The iterative reconstruction algorithm is activated during fluoroscopy.. · Elsholtz FH, Kamp JE, Vahldiek JL et al. Periradicular Infiltration of the Cervical Spine: How New CT Scanner Techniques and Protocol Modifications Contribute to the Achievement of Low-Dose Interventions. Fortschr Röntgenstr 2018; DOI: 10.1055/a-0632-3930. © Georg Thieme Verlag KG Stuttgart · New York.

Improving TOGAF ADM 9.1 Migration Planning Phase by ITIL V3 Service Transition

NASA Astrophysics Data System (ADS)

Hanum Harani, Nisa; Akhmad Arman, Arry; Maulana Awangga, Rolly

2018-04-01

Modification planning of business transformation involving technological utilization required a system of transition and migration planning process. Planning of system migration activity is the most important. The migration process is including complex elements such as business re-engineering, transition scheme mapping, data transformation, application development, individual involvement by computer and trial interaction. TOGAF ADM is the framework and method of enterprise architecture implementation. TOGAF ADM provides a manual refer to the architecture and migration planning. The planning includes an implementation solution, in this case, IT solution, but when the solution becomes an IT operational planning, TOGAF could not handle it. This paper presents a new model framework detail transitions process of integration between TOGAF and ITIL. We evaluated our models in field study inside a private university.

Microscale surface modifications for heat transfer enhancement.

PubMed

Bostanci, Huseyin; Singh, Virendra; Kizito, John P; Rini, Daniel P; Seal, Sudipta; Chow, Louis C

2013-10-09

In this experimental study, two surface modification techniques were investigated for their effect on heat transfer enhancement. One of the methods employed the particle (grit) blasting to create microscale indentations, while the other used plasma spray coating to create microscale protrusions on Al 6061 (aluminum alloy 6061) samples. The test surfaces were characterized using scanning electron microscopy (SEM) and confocal scanning laser microscopy. Because of the surface modifications, the actual surface area was increased up to 2.8× compared to the projected base area, and the arithmetic mean roughness value (Ra) was determined to vary from 0.3 μm for the reference smooth surface to 19.5 μm for the modified surfaces. Selected samples with modified surfaces along with the reference smooth surface were then evaluated for their heat transfer performance in spray cooling tests. The cooling system had vapor-atomizing nozzles and used anhydrous ammonia as the coolant in order to achieve heat fluxes up to 500 W/cm(2) representing a thermal management setting for high power systems. Experimental results showed that the microscale surface modifications enhanced heat transfer coefficients up to 76% at 500 W/cm(2) compared to the smooth surface and demonstrated the benefits of these practical surface modification techniques to enhance two-phase heat transfer process.

Optimising Laser Tattoo Removal

PubMed Central

Sardana, Kabir; Ranjan, Rashmi; Ghunawat, Sneha

2015-01-01

Lasers are the standard modality for tattoo removal. Though there are various factors that determine the results, we have divided them into three logical headings, laser dependant factors such as type of laser and beam modifications, tattoo dependent factors like size and depth, colour of pigment and lastly host dependent factors, which includes primarily the presence of a robust immune response. Modifications in the existing techniques may help in better clinical outcome with minimal risk of complications. This article provides an insight into some of these techniques along with a detailed account of the factors involved in tattoo removal. PMID:25949018

An analysis of thermal response factors and how to reduce their computational time requirement

NASA Technical Reports Server (NTRS)

Wiese, M. R.

1982-01-01

Te RESFAC2 version of the Thermal Response Factor Program (RESFAC) is the result of numerous modifications and additions to the original RESFAC. These modifications and additions have significantly reduced the program's computational time requirement. As a result of this work, the program is more efficient and its code is both readable and understandable. This report describes what a thermal response factor is; analyzes the original matrix algebra calculations and root finding techniques; presents a new root finding technique and streamlined matrix algebra; supplies ten validation cases and their results.

New Methodologies for Generation of Multigroup Cross Sections for Shielding Applications

NASA Astrophysics Data System (ADS)

Arzu Alpan, F.; Haghighat, Alireza

2003-06-01

Coupled neutron and gamma multigroup (broad-group) libraries used for Light Water Reactor shielding and dosimetry commonly include 47-neutron and 20-gamma groups. These libraries are derived from the 199-neutron, 42-gamma fine-group VITAMIN-B6 library. In this paper, we introduce modifications to the generation procedure of the broad-group libraries. Among these modifications, we show that the fine-group structure and collapsing technique have the largest impact. We demonstrate that a more refined fine-group library and the bi-linear adjoint weighting collapsing technique can improve the accuracy of transport calculation results.

Use of plan quality degradation to evaluate tradeoffs in delivery efficiency and clinical plan metrics arising from IMRT optimizer and sequencer compromises

PubMed Central

Wilkie, Joel R.; Matuszak, Martha M.; Feng, Mary; Moran, Jean M.; Fraass, Benedick A.

2013-01-01

Purpose: Plan degradation resulting from compromises made to enhance delivery efficiency is an important consideration for intensity modulated radiation therapy (IMRT) treatment plans. IMRT optimization and/or multileaf collimator (MLC) sequencing schemes can be modified to generate more efficient treatment delivery, but the effect those modifications have on plan quality is often difficult to quantify. In this work, the authors present a method for quantitative assessment of overall plan quality degradation due to tradeoffs between delivery efficiency and treatment plan quality, illustrated using comparisons between plans developed allowing different numbers of intensity levels in IMRT optimization and/or MLC sequencing for static segmental MLC IMRT plans. Methods: A plan quality degradation method to evaluate delivery efficiency and plan quality tradeoffs was developed and used to assess planning for 14 prostate and 12 head and neck patients treated with static IMRT. Plan quality was evaluated using a physician's predetermined “quality degradation” factors for relevant clinical plan metrics associated with the plan optimization strategy. Delivery efficiency and plan quality were assessed for a range of optimization and sequencing limitations. The “optimal” (baseline) plan for each case was derived using a clinical cost function with an unlimited number of intensity levels. These plans were sequenced with a clinical MLC leaf sequencer which uses >100 segments, assuring delivered intensities to be within 1% of the optimized intensity pattern. Each patient's optimal plan was also sequenced limiting the number of intensity levels (20, 10, and 5), and then separately optimized with these same numbers of intensity levels. Delivery time was measured for all plans, and direct evaluation of the tradeoffs between delivery time and plan degradation was performed. Results: When considering tradeoffs, the optimal number of intensity levels depends on the treatment site and on the stage in the process at which the levels are limited. The cost of improved delivery efficiency, in terms of plan quality degradation, increased as the number of intensity levels in the sequencer or optimizer decreased. The degradation was more substantial for the head and neck cases relative to the prostate cases, particularly when fewer than 20 intensity levels were used. Plan quality degradation was less severe when the number of intensity levels was limited in the optimizer rather than the sequencer. Conclusions: Analysis of plan quality degradation allows for a quantitative assessment of the compromises in clinical plan quality as delivery efficiency is improved, in order to determine the optimal delivery settings. The technique is based on physician-determined quality degradation factors and can be extended to other clinical situations where investigation of various tradeoffs is warranted. PMID:23822412

Clustering: An Interactive Technique to Enhance Learning in Biology.

ERIC Educational Resources Information Center

Ambron, Joanna

1988-01-01

Explains an interdisciplinary approach to biology and writing which increases students' mastery of vocabulary, scientific concepts, creativity, and expression. Describes modifications of the clustering technique used to summarize lectures, integrate reading and understand textbook material. (RT)

Measurement, testing, and safety technology: A compilation

NASA Technical Reports Server (NTRS)

1974-01-01

Methods and techniques in the related areas of measurement, testing, and safety are presented. Measuring techniques and devices and testing methods and devices are described. Articles on equipment modifications or procedures are included. Patent information is presented.

Science and Engineering Technical Assessments (SETA) Program

NASA Technical Reports Server (NTRS)

Huy, Frank

2000-01-01

This document provides a project plan for the D.N. American response to Modification #1 to Contract Task Order #13 - Program Maintenance and Logistics for the Science and Engineering Technical Assessments (SETA) contract.

40 CFR 52.2320 - Identification of plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... dated February 5, 1985, HAFB AO for Paint Booth, HVAC Modification, Standby Generators, and Fuel Storage... implementation of the inspection of vehicle On-Board Diagnostic (OBD) systems starting January 1, 2002 in all...

40 CFR 52.2320 - Identification of plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... dated February 5, 1985, HAFB AO for Paint Booth, HVAC Modification, Standby Generators, and Fuel Storage... implementation of the inspection of vehicle On-Board Diagnostic (OBD) systems starting January 1, 2002 in all...

40 CFR 52.2320 - Identification of plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... dated February 5, 1985, HAFB AO for Paint Booth, HVAC Modification, Standby Generators, and Fuel Storage... implementation of the inspection of vehicle On-Board Diagnostic (OBD) systems starting January 1, 2002 in all...

40 CFR 1.27 - Offices of the Associate Administrators.

Code of Federal Regulations, 2013 CFR

2013-07-01

... establishes Agency policy, and approves annual plans and modifications for travel abroad and attendance at.... The Office initiates and conducts on-site field visits to study, analyze, and resolve problems of...

40 CFR 1.27 - Offices of the Associate Administrators.

Code of Federal Regulations, 2014 CFR

2014-07-01

... establishes Agency policy, and approves annual plans and modifications for travel abroad and attendance at.... The Office initiates and conducts on-site field visits to study, analyze, and resolve problems of...

40 CFR 1.27 - Offices of the Associate Administrators.

Code of Federal Regulations, 2011 CFR

2011-07-01

... establishes Agency policy, and approves annual plans and modifications for travel abroad and attendance at.... The Office initiates and conducts on-site field visits to study, analyze, and resolve problems of...

40 CFR 1.27 - Offices of the Associate Administrators.

Code of Federal Regulations, 2010 CFR

2010-07-01

... establishes Agency policy, and approves annual plans and modifications for travel abroad and attendance at.... The Office initiates and conducts on-site field visits to study, analyze, and resolve problems of...

Crystal Growth Furnace System Configuration and Planned Experiments on the Second United States Microgravity Laboratory Mission

NASA Technical Reports Server (NTRS)

Srinivas, R.; Hambright, G.; Ainsworth, M.; Fiske, M.; Schaefer, D.

1995-01-01

The Crystal Growth Furnace (CGF) is currently undergoing modifications and refurbishment and is currently undergoing modifications and refurbishment and is manifested to refly on the Second United States Microgravity Laboratory (USML-2) mission scheduled for launch in September 1995. The CGF was developed for the National Aeronautics and Space Administration (NASA) under the Microgravity Science and Applications Division (MSAD) programs at NASA Headquarters. The refurbishment and reflight program is being managed by the Marshall Space Flight Center (MSFC) in Huntsville, Alabama. Funding and program support for the CGF project is provided to MSFC by the office of Life and Microgravity Sciences and Applications at NASA Headquarters. This paper presents an overview of the CGF system configuration for the USML-2 mission, and provides a brief description of the planned on-orbit experiment operation.

Impact of actuarial assumptions on pension costs: A simulation analysis

NASA Astrophysics Data System (ADS)

Yusof, Shaira; Ibrahim, Rose Irnawaty

2013-04-01

This study investigates the sensitivity of pension costs to changes in the underlying assumptions of a hypothetical pension plan in order to gain a perspective on the relative importance of the various actuarial assumptions via a simulation analysis. Simulation analyses are used to examine the impact of actuarial assumptions on pension costs. There are two actuarial assumptions will be considered in this study which are mortality rates and interest rates. To calculate pension costs, Accrued Benefit Cost Method, constant amount (CA) modification, constant percentage of salary (CS) modification are used in the study. The mortality assumptions and the implied mortality experience of the plan can potentially have a significant impact on pension costs. While for interest rate assumptions, it is inversely related to the pension costs. Results of the study have important implications for analyst of pension costs.

Deep patch technique for landslide repair. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helwany, B.M.

1994-10-01

The report describes the laboratory testing of the `USFS deep patch` technique and a CTI modification of this technique for repairing landslides with geosynthetic reinforcement. The technique involves replacing sections of roadway lost due to landslides on top of a geosynthetically-reinforced embankment. The CTI modification involves replacing the reinforced slope with a geosynthetically-reinforced retaining wall with a truncated base. Both techniques rely on the cantilevering ability of the reinforced mass to limit the load on the foundation with a high slide potential. The tests with road base showed that (1) both the USFS and CTI repair reduced effectively the adversemore » effects of local landsliding on the highway pavement by preventing crack propagation; (2) the USFS repair increased the stability of the repaired slope, which was in progressive failure, by reducing the stresses exerted on it; and (3) the CTI repair produced substantially greater stresses on its foundation due to the truncated base of the reinforced mass.« less

Integrated skin flash planning technique for intensity-modulated radiation therapy for vulvar cancer prevents marginal misses and improves superficial dose coverage.

PubMed

Dyer, Brandon A; Jenshus, Abriel; Mayadev, Jyoti S

2018-02-28

Radiation therapy (RT) plays a definitive role in locally advanced vulvar cancer, and in the adjuvant setting with high risk postoperative features after wide local excision. There is significant morbidity associated with traditional, large RT fields using 2D or 3D techniques, and the use of intensity-modulated radiation therapy (IMRT) in vulvar cancer is increasing. However, there remains a paucity of technical information regarding the prevention of a marginal miss during the treatment planning process. The use of an integrated skin flash (ISF) during RT planning can be used to account for anatomic variation, and intra- and interfraction motion seen during treatment. Herein we present the case of a patient with a T1aN0M0, Stage IA vulva cancer to illustrate the progressive vulvar swelling and lymph edema seen during treatment and retrospectively evaluate the dosimetric effects of using an ISF RT plan vs standard RT planning techniques. Standard planning techniques to treat vulvar cancer patients with IMRT do not sufficiently account for the change in patient anatomy and can lead to a marginal miss. ISF is an RT planning technique that can decrease the risk of a marginal miss and the technique is easily implemented during the planning stages of RT treatment. Furthermore, use of an ISF technique can improve vulvar clinical target volume coverage and plan homogeneity. Based on our experience, and this study, a 2-cm ISF is suggested to account for variations in daily clinical setup and changes in patient anatomy during treatment. Published by Elsevier Inc.

Design definition study of NASA/Navy lift/cruise fan V/STOL aircraft

NASA Technical Reports Server (NTRS)

1975-01-01

Assessed are the risks associated with the lift/cruise fan technology V/STOL aircraft program. Three candidate concepts for the technology aircraft design approach are considered: the lowspeed only modification, the full performance modification, and the all new aircraft concepts. Survey results indicate that the lift/cruise fan technology aircraft program is feasible, from the standpoint of technical risk, with some evidence of uncertainty of meeting the planned schedule and relatively minor impact on estimated program costs.

Recent progress in plasma-assisted synthesis and modification of 2D materials

NASA Astrophysics Data System (ADS)

Han, Zhao Jun; Murdock, Adrian T.; Seo, Dong Han; Bendavid, Avi

2018-07-01

Plasma represents an important technique for both the synthesis and modification of two-dimensional (2D) materials, owing to the unique plasma-material interactions which can enable effective energy transfer at the nanoscale. Non-equilibrium and non-thermal plasma techniques have been widely applied on various 2D materials, including graphene, silicene, germanene, phosphorene, hexagonal boron nitride (h-BN), and transition metal dichalcogenides such as MoS2 and WS2. Here, we review the recent progress in plasma-assisted synthesis and modification (e.g. functionalisation, doping and etching) of 2D materials and discuss the potential applications of this unique branch of 2D materials. Challenges and future research opportunities in the relevant research field are also discussed. The primary aim of this Review is to provide a better understanding of the plasma-assisted processes and to promote the utilization of 2D materials for advanced electronic, optoelectronic, sensing and energy storage applications.

Damage-free polymer surface modification employing inward-type plasma

NASA Astrophysics Data System (ADS)

Kanou, Ryo; Suga, Hiroshi; Utsumi, Hideyuki; Takahashi, Satoshi; Shirayama, Yuya; Watanabe, Norimichi; Petit, Stèphane; Shimizu, Tetsuo

2017-08-01

Inward-type plasmas, which spread upstream against the gas flow in the capillary tube where the gas is discharged, can react with samples placed near the entrance of such a capillary tube. In this study, surface modification of polymer surfaces is conducted using inward plasma. The modification is also done by conventional microplasma jet, and the modified surfaces with two plasma techniques are characterized by contact angle measurement, X-ray photoemission spectroscopy (XPS), and atomic force microscopy (AFM). Although inward-plasma-treated surfaces are less hydrophilic than conventional plasma-treated ones, they are still sufficiently hydrophilic for surface coatings. In addition, it turns out that the polymer surfaces irradiated with the inward plasma yield much smoother surfaces than those treated with the conventional plasma jet. Thus, the inward plasma treatment is a viable technique when the surface flatness is crucial, such as for the surface coating of plastic lenses.

In Vivo Multiparametric Ultrasound Imaging of Structural and Functional Tumor Modifications during Therapy.

PubMed

Dizeux, Alexandre; Payen, Thomas; Le Guillou-Buffello, Delphine; Comperat, Eva; Gennisson, Jean-Luc; Tanter, Mickael; Oelze, Michael; Bridal, S Lori

2017-09-01

Longitudinal imaging techniques are needed that can meaningfully probe the tumor microenvironment and its spatial heterogeneity. Contrast-enhanced ultrasound, shear wave elastography and quantitative ultrasound are ultrasound-based techniques that provide information on the vascular function and micro-/macroscopic tissue structure. Modifications of the tumor microenvironment induced by cytotoxic and anti-angiogenic molecules in ectopic murine Lewis lung carcinoma tumors were monitored. The most heterogenous structures were found in tumors treated with anti-angiogenic drug that simultaneously accumulated the highest levels of necrosis and fibrosis. The anti-angiogenic group presented the highest number of correlations between parameters related to vascular function and those related to the micro-/macrostructure of the tumor microenvironment. Results suggest how patterns of multiparametric ultrasound modifications can be related to provide a more insightful marker of changes occurring within tumors during therapy. Copyright © 2017. Published by Elsevier Inc.

Preparation of highly hydrophobic cotton fabrics by modification with bifunctional silsesquioxanes in the sol-gel process

NASA Astrophysics Data System (ADS)

Przybylak, Marcin; Maciejewski, Hieronim; Dutkiewicz, Agnieszka

2016-11-01

The surface modification of cotton fabrics was carried out using two types of bifunctional fluorinated silsesquioxanes with different ratios of functional groups. The modification was performed either by one- or two-step process. Two methods, the sol-gel and the dip coating method were used in different configurations. The heat treatment and the washing process were applied after modification. The wettability of cotton fabric was evaluated by measuring water contact angles (WCA). Changes in the surface morphology were examined by scanning electron microscopy (SEM, SEM-LFD) and atomic force microscopy (AFM). Moreover, the modified fabrics were subjected to analysis of elemental composition of the applied coatings using SEM-EDS techniques. Highly hydrophobic textiles were obtained in all cases studied and one of the modifications resulted in imparting superhydrophobic properties. Most of impregnated textiles remained hydrophobic even after multiple washing process which shows that the studied modification is durable.

Aiding planning in air traffic control: an experimental investigation of the effects of perceptual information integration.

PubMed

Moertl, Peter M; Canning, John M; Gronlund, Scott D; Dougherty, Michael R P; Johansson, Joakim; Mills, Scott H

2002-01-01

Prior research examined how controllers plan in their traditional environment and identified various information uncertainties as detriments to planning. A planning aid was designed to reduce this uncertainty by perceptually representing important constraints. This included integrating spatial information on the radar screen with discrete information (planned sequences of air traffic). Previous research reported improved planning performance and decreased workload in the planning aid condition. The purpose of this paper was to determine the source of these performance improvements. Analysis of computer interactions using log-linear modeling showed that the planning interface led to less repetitive--but more integrated--information retrieval compared with the traditional planning environment. Ecological interface design principles helped explain how the integrated information retrieval gave rise to the performance improvements. Actual or potential applications of this research include the design and evaluation of interface automation that keeps users in active control by modification of perceptual task characteristics.

International Population Assistance and Family Planning Programs: Issues for Congress

DTIC Science & Technology

2008-07-24

birth control . This policy, however, has generated contentious debate for over two decades, resulting in frequent clarification and modification of U.S. international family planning programs. In 1984, controversy arose over U.S. population aid policy when the Reagan Administration introduced restrictions, which became known as the Mexico City policy. The Mexico City policy denies U.S. funds to foreign nongovernmental organizations (NGOs) that perform or promote abortion as a method of family planning -- even if the activities are undertaken with non-U.S. funds. Presidents

A user interface for a knowledge-based planning and scheduling system

NASA Technical Reports Server (NTRS)

Mulvehill, Alice M.

1988-01-01

The objective of EMPRESS (Expert Mission Planning and Replanning Scheduling System) is to support the planning and scheduling required to prepare science and application payloads for flight aboard the US Space Shuttle. EMPRESS was designed and implemented in Zetalisp on a 3600 series Symbolics Lisp machine. Initially, EMPRESS was built as a concept demonstration system. The system has since been modified and expanded to ensure that the data have integrity. Issues underlying the design and development of the EMPRESS-I interface, results from a system usability assessment, and consequent modifications are described.

Photoelastic analysis of stress distribution in oral rehabilitation.

PubMed

Turcio, Karina Helga Leal; Goiato, Marcelo Coelho; Gennari Filho, Humberto; dos Santos, Daniela Micheline

2009-03-01

The purpose of this study was to present a literature review about photoelasticity, a laboratory method for evaluation of implants prosthesis behavior. Fixed or removable prostheses function as levers on supporting teeth, allowing forces to cause tooth movement if not carefully planned. Hence, during treatment planning, the dentist must be aware of the biomechanics involved and prevent movement of supporting teeth, decreasing lever-type forces generated by these prosthesis. Photoelastic analysis has great applicability in restorative dentistry as it allows prediction and minimization of biomechanical critical points through modifications in treatment planning.

Effects of wing modification on an aircraft's aerodynamic parameters as determined from flight data

NASA Technical Reports Server (NTRS)

Hess, R. A.

1986-01-01

A study of the effects of four wing-leading-edge modifications on a general aviation aircraft's stability and control parameters is presented. Flight data from the basic aircraft configuration and configurations with wing modifications are analyzed to determine each wing geometry's stability and control parameters. The parameter estimates and aerodynamic model forms are obtained using the stepwise regression and maximum likelihood techniques. The resulting parameter estimates and aerodynamic models are verified using vortex-lattice theory and by analysis of each model's ability to predict aircraft behavior. Comparisons of the stability and control derivative estimates from the basic wing and the four leading-edge modifications are accomplished so that the effects of each modification on aircraft stability and control derivatives can be determined.

Simultaneous Sterilization With Surface Modification Of Plastic Bottle By Plasma-Based Ion Implantation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sakudo, N.; Ikenaga, N.; Ikeda, F.

2011-01-07

Dry sterilization of polymeric material is developed. The technique utilizes the plasma-based ion implantation which is same as for surface modification of polymers. Experimental data for sterilization are obtained by using spores of Bacillus subtilis as samples. On the other hand we previously showed that the surface modification enhanced the gas barrier characteristics of plastic bottles. Comparing the implantation conditions for the sterilization experiment with those for the surface modification, we find that both sterilization and surface modification are simultaneously performed in a certain range of implantation conditions. This implies that the present bottling system for plastic vessels will bemore » simplified and streamlined by excluding the toxic peroxide water that has been used in the traditional sterilization processes.« less

Three pledget technique for closure of muscular ventricular septal defects.

PubMed

Sharma, Rajesh; Katewa, Ashish

2012-07-01

We propose a modification of the simple, horizontal mattress, pledgetted suture technique for closing the small muscular ventricular septal defect (VSD) by interposing an oversized third pledget on the left ventricular (LV) aspect of the defect.

Fluoxetine combined with clorazepate dipotassium and behaviour modification for treatment of anxiety-related disorders in dogs.

PubMed

Pineda, S; Anzola, B; Olivares, A; Ibáñez, M

2014-03-01

The effectiveness of clorazepate dipotassium combined with fluoxetine and a behaviour modification programme for the treatment of anxiety disorders in dogs was investigated. Forty dogs with anxiety disorders were initially enrolled and 36 dogs completed the trial. Dogs were classified into two behavioural categories (anxious dogs with aggression and anxious dogs without aggression) according to their presenting complaints, and were also subdivided into males, females, juveniles and adults. The dog owners were provided with a behaviour modification plan for their dogs to be commenced in the first week of therapy. Clorazepate dipotassium was administered PO at 1.0 mg/kg every 24 h for 4 weeks, and fluoxetine was administered PO at 1.0 mg/kg every 24 h for 10 weeks. Therapy with both drugs was initiated simultaneously. Improvement was reported in 25/36 dogs. Significant differences in treatment effects were observed between anxious dogs with aggression and anxious dogs without aggression (P<0.05). Positive correlations between owner compliance with the treatment plan and reported improvement achieved during three periods of study were also noted. Copyright © 2013 Elsevier Ltd. All rights reserved.

Basic procedures for epigenetic analysis in plant cell and tissue culture.

PubMed

Rodríguez, José L; Pascual, Jesús; Viejo, Marcos; Valledor, Luis; Meijón, Mónica; Hasbún, Rodrigo; Yrei, Norma Yague; Santamaría, María E; Pérez, Marta; Fernández Fraga, Mario; Berdasco, María; Rodríguez Fernández, Roberto; Cañal, María J

2012-01-01

In vitro culture is one of the most studied techniques, and it is used to study many developmental processes, especially in forestry species, because of growth timing and easy manipulation. Epigenetics has been shown as an important influence on many research analyses such as cancer in mammals and developmental processes in plants such as flowering, but regarding in vitro culture, techniques to study DNA methylation or chromatin modifications were mainly limited to identify somaclonal variation of the micropropagated material. Because in vitro culture is not only a way to generate plant material but also a bunch of differentially induced developmental processes, an approach of techniques and some research carried out to study the different changes regarding DNA methylation and chromatin and translational modifications that take place during these processes is reviewed.

Satellite detection of smoke plumes and inadvertant weather modification

Treesearch

Wayne A. Pettyjohn; John B. McKeon

1976-01-01

Satellite imagery provides a convenient and inexpensive means for monitoring smoke plumes and evaluating inadvertant weather modification. Visual examination of LANDSAT-1 imagery for two sites in east-central Ohio indicates that, at times, a plume may extend nearly 48 km downwind and reach a width of six km. Density slicing techniques provide clues as to the...

Behavior Modification for Children with Autistic Tendencies; Study Guide for a Videotaped Series.

ERIC Educational Resources Information Center

Ackerman, Arthur; Dirr, Peter J.

The study guide accompanies a series of 28 videotaped programs designed to provide teachers, teacher aides and parents with an understanding of children with autistic tendencies and of how behavior modification techniques might be used to train such children. Synopses of each program and each program segment and a few questions intended to…

A Proposal: Modification for Instruments and Tools Used in the Science Laboratory Setting for Students with Disabilities

ERIC Educational Resources Information Center

Kogan, Denis

2015-01-01

The purpose of this action research proposal is to create a Modification of Instruments and Tools in Science (MITS) program to address the need for providing Students With Disabilities (SWDs) appropriate access to scientific tools and techniques of scientific inquiry. This proposal contains a review of literature on SWDs, differentiating…

Single-stage autologous ear reconstruction for microtia.

PubMed

Kasrai, Leila; Snyder-Warwick, Alison K; Fisher, David M

2014-03-01

The authors have been using the Nagata technique since 2002. In this review of 100 consecutive ear reconstructions, the authors present technique modifications that have evolved over this period that have contributed to improved auricular contour and that now allow for auricular reconstruction in a single stage. This study is a retrospective review of a prospectively acquired database. The series is restricted to primary reconstructions performed for congenital microtia. Photographs of 10 consecutive patients are presented to demonstrate the results of the technique. Surgical complication rates are discussed. One hundred ear reconstructions were performed in 96 patients. There were 75 primary cases of congenital microtia. Twenty-four ears underwent a two-stage reconstruction, and 51 ears were reconstructed with a Nagata stage I procedure or a single-stage reconstruction. There was a gradual shift in technique, with a trend to perform fewer Nagata stage II outsetting procedures and more single-stage reconstructions. In patients who underwent an ear reconstruction in two stages, the surgical complication rate was 22 percent. In the last 40 consecutive ear reconstructions since abandoning the two-stage approach, the surgical complication rate is now 15 percent. A modification of Nagata's technique of autologous ear reconstruction for microtia is described. Modifications of the three-dimensional framework address the contour of the inferior crus and control tragal projection and position. Inclusion of a projection block and recruitment of retroauricular skin allow for symmetric projection of the ear in a single stage. Therapeutic, IV.

Vaginal-sparing ventral buccal mucosal graft urethroplasty for female urethral stricture: A novel modification of surgical technique.

PubMed

Hoag, Nathan; Gani, Johan; Chee, Justin

2016-07-01

To present a novel modification of surgical technique to treat female urethral stricture (FUS) by a vaginal-sparing ventral buccal mucosal urethroplasty. Recurrent FUS represents an uncommon, though difficult clinical scenario to manage definitively. A variety of surgical techniques have been described to date, yet a lack of consensus on the optimal procedure persists. We present a 51-year-old female with urethral stricture involving the entire urethra. Suspected etiology was iatrogenic from cystoscopy 17 years prior. Since then, the patient had undergone at least 25 formal urethral dilations and periods of self-dilation. In lithotomy position, the urethra was dilated to accommodate forceps, and ventral urethrotomy carried out sharply, exposing a bed of periurethral tissue. Buccal mucosa was harvested, and a ventral inlay technique facilitated by a nasal speculum, was used to place the graft from the proximal urethra/bladder neck to urethral meatus without a vaginal incision. Graft was sutured into place, and urethral Foley catheter inserted. The vaginal-sparing ventral buccal mucosal graft urethroplasty was deemed successful as of last follow-up. Flexible cystoscopy demonstrated patency of the repair at 6 months. At 10 months of follow-up, the patient was voiding well, with no urinary incontinence. No further interventions have been required. This case describes a novel modification of surgical technique for performing buccal mucosal urethroplasty for FUS. By avoiding incision of the vaginal mucosa, benefits may include reduced: morbidity, urinary incontinence, and wound complications including urethro-vaginal fistula.

136. ARRII Plot plan as it appeared in 1980, when ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

136. ARR-II Plot plan as it appeared in 1980, when interior modifications were being prepared to remodel electrical apparatus in ARA-602 in connection with use as a research and development joining laboratory. EG&G, Idaho, Inc. 1570-ARA-II-100-1. Date: April 1980. Ineel index code no. 070-0199-00-220-159749. - Idaho National Engineering Laboratory, Army Reactors Experimental Area, Scoville, Butte County, ID

Alvarado Flood Risk Management Modifications to Existing Project Section 408 Review. Review Plan

DTIC Science & Technology

2012-12-26

Digital Flood Insurance Rate Maps) through the Nationa l Flood Insurance Program ( NFIP ). In order to obtain FEMA accreditation, the levee owner...compliance documentation for meeting NFIP requirements. Barr conducted a thorough review of relevant documents to gain a better understanding of...compliance documentation for meeting NFIP requirements. Barr Engineering has prepared a Phase I Engineer’s Report and is developing plans and

Focal species and landscape "naturalness" corridor models offer complementary approaches for connectivity conservation planning

Treesearch

Meade Krosby; Ian Breckheimer; D. John Pierce; Peter H. Singleton; Sonia A. Hall; Karl C. Halupka; William L. Gaines; Robert A. Long; Brad H. McRae; Brian L. Cosentino; Joanne P. Schuett-Hames

2015-01-01

Context   The dual threats of habitat fragmentation and climate change have led to a proliferation of approaches for connectivity conservation planning. Corridor analyses have traditionally taken a focal species approach, but the landscape ‘‘naturalness’’ approach of modeling connectivity among areas of low human modification has gained popularity...

Recent advances in the chemical modification of unsaturated polymers

NASA Technical Reports Server (NTRS)

Schulz, D. N.; Turner, S. R.; Golub, M. A.

1982-01-01

The present discussion has the objective to update the most comprehensive reviews on the considered subject and to fill in the gaps of less complete, but more modern treatments. Only simple chemical functionalization or structural modification of unsaturated polymers are covered, and the literature of diene polymer modification since 1974 is emphasized. Attention is given to hydrogenation, halogenation and hydrohalogenation, cyclization, cis-trans isomerization, epoxidation, ene and other cycloaddition reactions, sulfonation, carboxylation, phosphonylation, sulfenyl chloride addition, carbene addition, metalation, and silylation. It is pointed out that modern synthetic reagents and catalysts have been advantageously employed to improve process and/or product quality. Synthetic techniques have been refined to allow the selective modification of specific polymer microstructures or blocks.

Plasma assisted surface coating/modification processes - An emerging technology

NASA Technical Reports Server (NTRS)

Spalvins, T.

1987-01-01

A broad understanding of the numerous ion or plasma assisted surface coating/modification processes is sought. An awareness of the principles of these processes is needed before discussing in detail the ion nitriding technology. On the basis of surface modifications arising from ion or plasma energizing and interactions, it can be broadly classified as deposition of distinct overlay coatings (sputtering-dc, radio frequency, magnetron, reactive; ion plating-diode, triode) and surface property modification without forming a discrete coating (ion implantation, ion beam mixing, laser beam irradiation, ion nitriding, ion carburizing, plasma oxidation. These techniques offer a great flexibility and are capable in tailoring desirable chemical and structural surface properties independent of the bulk properties.

Plasma assisted surface coating/modification processes: An emerging technology

NASA Technical Reports Server (NTRS)

Spalvins, T.

1986-01-01

A broad understanding of the numerous ion or plasma assisted surface coating/modification processes is sought. An awareness of the principles of these processes is needed before discussing in detail the ion nitriding technology. On the basis of surface modifications arising from ion or plasma energizing and interactions, it can be broadly classified as deposition of distinct overlay coatings (sputtering-dc, radio frequency, magnetron, reactive; ion plating-diode, triode) and surface property modification without forming a discrete coating (ion implantation, ion beam mixing, laser beam irradiation, ion nitriding, ion carburizing, plasma oxidation). These techniques offer a great flexibility and are capable in tailoring desirable chemical and structural surface properties independent of the bulk properties.

Modification of smoothing in 4253H[T

NASA Astrophysics Data System (ADS)

Azmi, Nurul Nisa'Khairol; Adam, Mohd Bakri; Shitan, Mahendran; Ali, Norhaslinda Mohd

2017-05-01

Some modified non-linear smoothers particularly 4253H[T] are explained in this paper. The modifications are focused on estimating the middle point of running median for even span by applying the following types of means; geometric, harmonic, quadratic and contraharmonic. The performance of the techniques is assessed by applying it to daily price index of a bank in Malaysia that issues sukuk for funding in Islamic banking and financial business. The results show that 4253H[T] with geometric mean modification is better than others in preserving variation and curve fitting.

Speckle contrast techniques in the study of tissue thermal modification and denaturation

NASA Astrophysics Data System (ADS)

Agafonov, Dmitry N.; Kuznetsova, Liana V.; Zimnyakov, Dmitry A.; Sviridov, Alexander P.; Omelchenko, Alexander I.

2002-05-01

Results of the contrast analysis of time-averaged dynamic speckle patterns in application to monitoring of the structure modification of the thermally treated collagenous tissue such as cartilage are presented. The modification presumably induced by the bound to free water phase transition in the matrix of the treated tissue cause the specific feature of evolution of the time-averaged speckle contrast with the change of the current temperature of modified collagen tissue. This evolution appears as hysteresis associated with irreversible changes in tissue structure.

TiO2 induced structural modifications in Cs containing borosilicate glasses: Raman and infrared studies

NASA Astrophysics Data System (ADS)

Pandey, M.; Banerjee, D.; Sudarsan, V.; Kshirsagar, R. J.

2018-04-01

Effect of TiO2 addition in Cs containing Sodium-borosilicate glasses is studied using Raman and infrared spectroscopic techniques. As revealed from infrared and Raman studies, TiO2 does not form segregated phase, but instead enters into the borosilicate network. It is further observed that TiO2 addition results in modifications of the borate and silicate structural units by transforming into tetraborates and metasilicate structural units. These structural modifications are responsible for Cs immobilization, leach rate and chemical durability of these glasses.

Monitoring Prepregs As They Cure

NASA Technical Reports Server (NTRS)

Young, P. R.; Gleason, J. R.; Chang, A. C.

1986-01-01

Quality IR spectra obtained in dynamic heating environment. New technique obtains quality infrared spectra on graphite-fiber-reinforced, polymeric-matrix-resin prepregs as they cure. Technique resulted from modification of diffuse reflectance/Fourier transform infrared (DR/FTIR) technique previously used to analyze environmentally exposed cured graphite composites. Technique contribute to better understanding of prepreg chemistry/temperature relationships and development of more efficient processing cycles for advanced materials.

A methodology for evaluating the usability of audiovisual consumer electronic products.

PubMed

Kwahk, Jiyoung; Han, Sung H

2002-09-01

Usability evaluation is now considered an essential procedure in consumer product development. Many studies have been conducted to develop various techniques and methods of usability evaluation hoping to help the evaluators choose appropriate methods. However, planning and conducting usability evaluation requires considerations of a number of factors surrounding the evaluation process including the product, user, activity, and environmental characteristics. In this perspective, this study suggested a new methodology of usability evaluation through a simple, structured framework. The framework was outlined by three major components: the interface features of a product as design variables, the evaluation context consisting of user, product, activity, and environment as context variables, and the usability measures as dependent variables. Based on this framework, this study established methods to specify the product interface features, to define evaluation context, and to measure usability. The effectiveness of this methodology was demonstrated through case studies in which the usability of audiovisual products was evaluated by using the methods developed in this study. This study is expected to help the usability practitioners in consumer electronics industry in various ways. Most directly, it supports the evaluators' plan and conduct usability evaluation sessions in a systematic and structured manner. In addition, it can be applied to other categories of consumer products (such as appliances, automobiles, communication devices, etc.) with minor modifications as necessary.

Sub-second pencil beam dose calculation on GPU for adaptive proton therapy.

PubMed

da Silva, Joakim; Ansorge, Richard; Jena, Rajesh

2015-06-21

Although proton therapy delivered using scanned pencil beams has the potential to produce better dose conformity than conventional radiotherapy, the created dose distributions are more sensitive to anatomical changes and patient motion. Therefore, the introduction of adaptive treatment techniques where the dose can be monitored as it is being delivered is highly desirable. We present a GPU-based dose calculation engine relying on the widely used pencil beam algorithm, developed for on-line dose calculation. The calculation engine was implemented from scratch, with each step of the algorithm parallelized and adapted to run efficiently on the GPU architecture. To ensure fast calculation, it employs several application-specific modifications and simplifications, and a fast scatter-based implementation of the computationally expensive kernel superposition step. The calculation time for a skull base treatment plan using two beam directions was 0.22 s on an Nvidia Tesla K40 GPU, whereas a test case of a cubic target in water from the literature took 0.14 s to calculate. The accuracy of the patient dose distributions was assessed by calculating the γ-index with respect to a gold standard Monte Carlo simulation. The passing rates were 99.2% and 96.7%, respectively, for the 3%/3 mm and 2%/2 mm criteria, matching those produced by a clinical treatment planning system.

Means to Overcome the Anxieties of Second Language Learners.

ERIC Educational Resources Information Center

McCoy, Ingeborg R.

1979-01-01

Behavior modification techniques that can be used to overcome fears and anxieties of students and to further achievement in second language learning are discussed. The following techniques are covered: systematic desensitization, cognitive restructuring, and modeling and guided participation. (SW)

Performance of activities of daily living in a sample of applicants for home modification services.

PubMed

Johansson, Karin; Lilja, Margareta; Petersson, Ingela; Borell, Lena

2007-01-01

Home modification services are provided to support persons with functional limitations to live independently at home. It is not well known what causes individuals to apply for home modifications, or in what kind of life situation this need appears. The aim of this study was to examine the relationship between performance of activities of daily living, housing and living situation, and the home modification applied for in a sample of home modification applicants. Further, the aim was to examine differences in performance of activities of daily living between subgroups with different social support. A total of 102 participants were included in the study. Data on performance of activities of daily living was collected through interviews in the participants' homes, using structured instruments. The participants reported high levels of independence in activities of daily living, and were using assistive devices to a large extent. However, the applicants clearly experienced difficulties in performing activities related to the applied home modification. The study indicates that the main reason for applying for Home Modification Grants was perceived difficulties in performance of activities of daily living. This stresses the importance of including other aspects besides independence when trying to understand persons' activity performance and planning for occupational therapy interventions.

Minimal Nasolabial Incision Technique for Nasolabial Fold Modification in Patients With Facial Paralysis.

PubMed

Faris, Callum; Heiser, Alyssa; Jowett, Nate; Hadlock, Tessa

2018-03-01

Creation of symmetrical nasolabial folds (NLFs) is important in the management of the paralyzed face. Established techniques use a linear incision in the NLF, and technical refinements now allow the linear incision to be omitted. This retrospective case series was conducted in a tertiary care setting from February 2, 2017, to June 7, 2017. Participants were all patients (N = 21) with peripheral facial paralysis who underwent NLF modification that used the minimal nasolabial incision technique at the Massachusetts Eye and Ear Infirmary Facial Nerve Center from February 1, 2015, through August 31, 2016. Patient-reported outcome measures using the validated, quality-of-life Facial Clinimetric Evaluation (FaCE) Scale; clinician-reported facial function outcomes using a validated electronic clinician-graded facial paralysis assessment (eFACE); layperson assessment of the overall aesthetic outcome of the NLF; and expert-clinician scar assessment of the NLF. Of the 21 patients who underwent NLF modification that used the minimal nasolabial incision technique, 9 patients (43%) were female and 12 (57%) were male. The mean age was 41 (range, 9-90) years; 17 patients (81%) were adults (≥18 years) and 4 (19%) were children (<18 years). Overall, significant improvements were observed after NLF modification in all outcome measures as graded by both clinicians and patients. The mean (SD) scores for total eFACE were 60.7 (14.9) before the operation and 77.2 (8.9) after the operation (mean difference, 16.5 [95% CI, 8.5-24.2]; P < .001). The mean (SD) static eFACE scores were 61.4 (20.6) before the operation and 82.7 (12.4) after the operation (mean difference, 21.3 [95% CI, 10.7-31.9]; P < .001). The mean (SD) FaCE quality-of-life scores were 51.3 (20.1) before the operation and 70.3 (12.6) after the operation (mean difference, 19.0 [95% CI, 6.5-31.6]; P  =  .001). The layperson self-assessment of the overall aesthetic outcome of the NLF modification was higher among the group who had the minimal nasolabial incision than it was for the group who had a historical nasolabial incision (mean [SD], 68.17 [13.59] vs 56.28 [13.60]; mean difference, 11.89 [95% CI, 3.81-19.97]; P < .001). Similarly, the expert-clinician scar assessment of the NLF modification was higher for the group who had the minimal nasolabial incision than it was for the group who had a historical nasolabial incision (3.78 [0.91] vs 2.98 [0.81]; mean difference, 0.80 [95% CI, 0.29-1.32]; P  =  .007). The minimal nasolabial incision technique for NLF modification is effective in rehabilitating the NLF in facial paralysis without adding a long linear scar to the central midface. 4.

Comparison between DCA - SSO - VDR and VMAT dose delivery techniques for 15 SRS/SRT patients

NASA Astrophysics Data System (ADS)

Tas, B.; Durmus, I. F.

2018-02-01

To evaluate dose delivery between Dynamic Conformal Arc (DCA) - Segment Shape Optimization (SSO) - Variation Dose Rate (VDR) and Volumetric Modulated Arc Therapy (VMAT) techniques for fifteen SRS patients using Versa HD® lineer accelerator. Fifteen SRS / SRT patient's optimum treatment planning were performed using Monaco5.11® treatment planning system (TPS) with 1 coplanar and 3 non-coplanar fields for VMAT technique, then the plans were reoptimized with the same optimization parameters for DCA - SSO - VDR technique. The advantage of DCA - SSO - VDR technique were determined less MUs and beam on time, also larger segments decrease dosimetric uncertainities of small fields quality assurance. The advantage of VMAT technique were determined a little better GI, CI, PCI, brain V12Gy and brain mean dose. The results show that the clinical objectives and plans for both techniques satisfied all organs at risks (OARs) dose constraints. Depends on the shape and localization of target, we could choose one of these techniques for linear accelerator based SRS / SRT treatment.

A design support simulation of the augmentor wing jet STOL research aircraft

NASA Technical Reports Server (NTRS)

Rumsey, P. C.; Spitzer, R. E.; Glende, W. L. B.

1972-01-01

The modification of a C-8A (De Havilland Buffalo) aircraft to a STOL configuration is discussed. The modification consisted of the installation of an augmentor-wing jet flap system. System design requirements were investigated for the lateral and directional flight control systems, the lateral and directional axes stability augmentation systems, the engine and Pegasus nozzle control systems, and the hydraulic systems. Operational techniques for STOL landings, control of engine failures, and pilot techniques for improving engine-out go-around performance were examined. Design changes have been identified to correct deficiencies in areas of the airplane control sytems and to improve the airplane flying qualities.

En bloc sacrectomy and reconstruction: technique modification for pelvic fixation.

PubMed

Newman, C Benjamin; Keshavarzi, Sassan; Aryan, Henry E

2009-12-01

When the management of sacral tumors requires partial or complete sacrectomy, the spinopelvic apparatus must be reconstructed. This is a challenging and infrequently performed operation, and as such, many spine surgeons are unfamiliar with techniques available to carry out these procedures. A 34-year-old man presented with severe low back pain, mild left ankle dorsiflexion weakness, and left S1 paresthesias. Imaging revealed a large sacral mass extending into the L5/S1 and S1/S2 neural foramina as well as the presacral visceral and vascular structures. Needle biopsy of this mass demonstrated a low-grade chondrosarcoma. A 2-stage anterior/posterior en bloc sacrectomy with a novel modification of the Galveston L-rod pelvic ring reconstruction was carried out. Our modification takes advantage of new materials and implant technology to offer another alternative in reconstruction of the spinopelvic junction. Understanding the anatomy and biomechanics of the spinopelvic apparatus and the lumbosacral junction, as well as having a familiarity with the various techniques available for carrying out sacrectomy and pelvic ring reconstruction, will enable the spine surgeon to effectively manage sacral tumors. Copyright 2009 Elsevier Inc. All rights reserved.

Safety assessment tool for construction zone work phasing plans

DOT National Transportation Integrated Search

2016-05-01

The Highway Safety Manual (HSM) is the compilation of national safety research that provides quantitative methods for : analyzing highway safety. The HSM presents crash modification functions related to freeway work zone characteristics such as : wor...

Data needs for tree removal crash modification factors on Arizona state highways.

DOT National Transportation Integrated Search

2016-07-01

The Arizona Department of Transportation (ADOT) Roadway Departure Safety Implementation Plan (RDSIP) has : identified tree removal as a feasible countermeasure to reduce roadway departure crash frequency or severity. : Previous ADOT work has identifi...

36 CFR 223.235 - Unilateral delay, suspension, or modification of contracts, permits, or other instruments...

Code of Federal Regulations, 2011 CFR

2011-07-01

..., animals, cave resources, or cultural resources; (2) To ensure consistency with land management plans or... warrant oral communication, in which case the officer shall promptly follow-up in writing. ...

Artificial intelligence techniques for scheduling Space Shuttle missions

NASA Technical Reports Server (NTRS)

Henke, Andrea L.; Stottler, Richard H.

1994-01-01

Planning and scheduling of NASA Space Shuttle missions is a complex, labor-intensive process requiring the expertise of experienced mission planners. We have developed a planning and scheduling system using combinations of artificial intelligence knowledge representations and planning techniques to capture mission planning knowledge and automate the multi-mission planning process. Our integrated object oriented and rule-based approach reduces planning time by orders of magnitude and provides planners with the flexibility to easily modify planning knowledge and constraints without requiring programming expertise.

Agent independent task planning

NASA Technical Reports Server (NTRS)

Davis, William S.

1990-01-01

Agent-Independent Planning is a technique that allows the construction of activity plans without regard to the agent that will perform them. Once generated, a plan is then validated and translated into instructions for a particular agent, whether a robot, crewmember, or software-based control system. Because Space Station Freedom (SSF) is planned for orbital operations for approximately thirty years, it will almost certainly experience numerous enhancements and upgrades, including upgrades in robotic manipulators. Agent-Independent Planning provides the capability to construct plans for SSF operations, independent of specific robotic systems, by combining techniques of object oriented modeling, nonlinear planning and temporal logic. Since a plan is validated using the physical and functional models of a particular agent, new robotic systems can be developed and integrated with existing operations in a robust manner. This technique also provides the capability to generate plans for crewmembers with varying skill levels, and later apply these same plans to more sophisticated robotic manipulators made available by evolutions in technology.

Houston Operations Predictor/Estimator (HOPE) programming manual, volume 1. [Apollo orbit determination

NASA Technical Reports Server (NTRS)

Daly, J. K.

1974-01-01

The programming techniques used to implement the equations and mathematical techniques of the Houston Operations Predictor/Estimator (HOPE) orbit determination program on the UNIVAC 1108 computer are described. Detailed descriptions are given of the program structure, the internal program structure, the internal program tables and program COMMON, modification and maintainence techniques, and individual subroutine documentation.

Surface modification of protein enhances encapsulation in chitosan nanoparticles

NASA Astrophysics Data System (ADS)

Koyani, Rina D.; Andrade, Mariana; Quester, Katrin; Gaytán, Paul; Huerta-Saquero, Alejandro; Vazquez-Duhalt, Rafael

2018-04-01

Chitosan nanoparticles have a huge potential as nanocarriers for environmental and biomedical purposes. Protein encapsulation in nano-sized chitosan provides protection against inactivation, proteolysis, and other alterations due to environmental conditions, as well as the possibility to be targeted to specific tissues by ligand functionalization. In this work, we demonstrate that the chemical modification of the protein surface enhances the protein loading in chitosan nanocarriers. Encapsulation of green fluorescent protein and the cytochrome P450 was studied. The increase of electrostatic interactions between the free amino groups of chitosan and the increased number of free carboxylic groups in the protein surface enhance the protein loading, protein retention, and, thus, the enzymatic activity of chitosan nanoparticles. The chemical modification of protein surface with malonic acid moieties reduced drastically the protein isoelectric point increasing the protein interaction with the polycationic biomaterial and chitosan. The chemical modification of protein does not alter the morphology of chitosan nanoparticles that showed an average diameter of 18 nm, spheroidal in shape, and smooth surfaced. The strategy of chemical modification of protein surface, shown here, is a simple and efficient technique to enhance the protein loading in chitosan nanoparticles. This technique could be used for other nanoparticles based on polycationic or polyanionic materials. The increase of protein loading improves, doubtless, the performance of protein-loaded chitosan nanoparticles for biotechnological and biomedical applications.

A multitechnique evaluation of topical corticosteroid treatment.

PubMed

Josse, G; Rouvrais, C; Mas, A; Haftek, M; Delalleau, A; Ferraq, Y; Ossant, F; George, J; Lagarde, J M; Schmitt, A M

2009-02-01

Corticosteroids are widely prescribed for systemic or local treatment of inflammatory autoimmune disorders. Long-term therapy is associated with side effects and causes cutaneous atrophy of the epidermis and the dermis. The present study aims to evaluate with several noninvasive techniques, the skin modifications observed during corticosteroids treatment. The potential of skin mechanical measurement and ultrasound radio frequency (RF) signal analysis are proposed as new measures more closely related to the functional impairments. Thirteen young healthy women volunteers had two applications per day on one arm of topical Clobetasol propionate 0.05% for 28 days, and they were followed for 28 days more. Skin modifications were studied by high-frequency ultrasound imaging, ultrasound RF signal analysis, optical coherence tomography and by the suction test. For all the techniques, a statistically significant change is observed with treatment. Large variations, around 30%, are observed for all techniques, but less for ultrasound imaging (10%). Dermis and epidermis thickness presented stable measurements on the nontreated zone. At the end of the study, measures returned to normal. The dynamic is mainly observed within the first 14 days of treatment and within the first 14 days after its cessation. Similar dynamics of skin modification during corticosteroid treatment was observed with very different techniques. Moreover, the potential of RF ultrasound analysis and mechanical skin measurement for characterizing skin structural and functional impairments has been evaluated.

Micro- and nanoscale devices for the investigation of epigenetics and chromatin dynamics

NASA Astrophysics Data System (ADS)

Aguilar, Carlos A.; Craighead, Harold G.

2013-10-01

Deoxyribonucleic acid (DNA) is the blueprint on which life is based and transmitted, but the way in which chromatin -- a dynamic complex of nucleic acids and proteins -- is packaged and behaves in the cellular nucleus has only begun to be investigated. Epigenetic modifications sit 'on top of' the genome and affect how DNA is compacted into chromatin and transcribed into ribonucleic acid (RNA). The packaging and modifications around the genome have been shown to exert significant influence on cellular behaviour and, in turn, human development and disease. However, conventional techniques for studying epigenetic or conformational modifications of chromosomes have inherent limitations and, therefore, new methods based on micro- and nanoscale devices have been sought. Here, we review the development of these devices and explore their use in the study of DNA modifications, chromatin modifications and higher-order chromatin structures.

TU-F-CAMPUS-J-01: Dosimetric Effects of HU Changes During the Course of Proton Therapy for Lung Cancer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teng, C; Yin, L; Ainsley, C

2015-06-15

Purpose: To characterize the changes in Hounsfield unit (HU) in lung radiotherapy with proton beams during the course of treatment and to study the effect on the proton plan dose distribution. Methods: Twenty consecutive patients with non-small cell lung cancer treated with proton radiotherapy who underwent multiple CT scans including the planning CT and weekly verification CTs were studied. HU histograms were computed for irradiated lung volumes in beam paths for all scans using the same treatment plan. Histograms for un-irradiated lung volume were used as control to characterize inter-scan variations. HU statistics were calculated for both irradiated and un-irradiatedmore » lung volumes for each patient scan. Further, multiple CT scans based on the same planning CT were generated by replacing the HU of the lung based on the verification CT scans HU values. Using the same beam arrangement, we created plans for each of the altered CT scans to study the dosimetric effect using the dose volume histogram. Results: Lung HU decreased for irradiated lung volume during the course of radiotherapy. The magnitude of this change increased with total irradiation dose. On average, HU changed by −53.8 in the irradiated volume. This change resulted in less than 0.5mm of beam overshoot in tissue for every 1cm beam traversed in the irradiated lung. The dose modification is about +3% for the lung, and less than +1% for the primary tumor. Conclusion: HU of the lung decrease throughout the course of radiation therapy. This change results in a beam overshoot (e.g. 3mm for 6cm of lung traversed) and causes a small dose modification in the overall plan. However, this overshoot does not affect the quality of plans since the margins used in planning, based on proton range uncertainty, are greater. HU needs to change by 150 units before re-planning is warranted.« less

An Interdisciplinary Approach toward the Treatment of Behavior and Learning Problems in a Special Educational Facility for Emotionally and Socially Handicapped Children.

ERIC Educational Resources Information Center

Comiskey, Vincent P.; And Others

Provided are some of the guidelines used in the Village School Behavior Modification Program for children with behavior problems in Bergen County, New Jersey. Included are definitions of the terms "emotionally disturbed" and "socially maladjusted", descriptions of some behavior modification techniques used, copies of forms and…