Ternary binder based plasters with improved thermal insulating ability

NASA Astrophysics Data System (ADS)

Čáchová, M.; Koňáková, D.; Vejmelková, E.; Vyšvařil, M.

2017-10-01

New kind of plasters with improved thermal insulating ability are presented in this article. Improvement was reached by utilization of lightweight expanded perlite with high porosity. The second used aggregate was silica sand. Regarding the binder, three kind were combined for the reason of better plaster performance. Pure lime, Portland cement and pozzolanic ceramic powder were employed. Basic physical properties and thermal characteristics were determined. The porosity of plasters reached desired higher value about 50% and the thermal conductivity in dry state was lower than 0.16 Wm-1K-1.

Mortality among unionized construction plasterers and cement masons.

PubMed

Stern, F; Lehman, E; Ruder, A

2001-04-01

Plasterers perform a variety of duties including interior and exterior plastering of drywall, cement, stucco, and stone imitation; the preparation, installation, and repair of all interior and exterior insulation systems; and the fireproofing of steel beams and columns. Some of the current potential toxic exposures among plasterers include plaster of Paris, silica, fiberglass, talc, and 1,1,1-trichloroethylene; asbestos had been used by the plasterers in the past. Cement masons, on the other hand, are involved in concrete construction of buildings, bridges, curbs and gutters, sidewalks, highways, streets and roads, floors and pavements and the finishing of same, when necessary, by sandblasting or any other method. Exposures include cement dust, silica, asphalt, and various solvents. Proportionate mortality ratios (PMRs) and proportionate cancer mortality ratios (PCMRs) were calculated for 99 causes of death among 12,873 members of the Operative Plasterers' and Cement Masons' International Association who died between 1972 and 1996 using United States age-, race-, and calender-specific death rates. Statistical significance (P value) of results was based upon the Poisson distribution. Among plasterers, statistically significant elevated mortality was observed for asbestosis, where the PMR reached 1,657 (P < 0.01) with eleven observed deaths and less than one death expected, for lung cancer (PCMR = 124, P < 0.01), and for benign neoplasms (PMR = 210, P < 0.05). Among cement masons, statistically significant elevated mortality was observed for cancer of the stomach (PCMR = 133, P < 0.01), benign neoplasms (PMR = 132, P < 0.01), and poisonings (PMR = 159, P < 0.05). Except for poisonings, which were not thought to be occupationally related, all of the statistically significant results occurred among those members who entered the union prior to 1950. However, the risk for lung cancer among plasterers was still elevated among those entering the union after 1970 as was the risk for stomach cancer among cement masons who entered the union after 1950. The present study suggests that plasterers and cement masons still have elevated risks for certain diseases, especially lung and stomach cancer. Therefore, union members currently living should be screened for asbestos-related diseases and educated about the future risks for these diseases.

Clay Portrait Boxes

ERIC Educational Resources Information Center

Wilbert, Nancy Corrigan

2009-01-01

In an attempt to incorporate sculptural elements into her ceramics program, the author decided to try direct plaster casting of the face to make a plaster mold for clay. In this article, the author shares an innovative ceramics lesson that teaches students in making plaster casts and casting the face in clay. This project gives students the…

Thermophysical properties of hydrophobised lime plasters - The influence of ageing

NASA Astrophysics Data System (ADS)

Pavlíková, Milena; Zemanová, Lucie; Pavlík, Zbyšek

2017-07-01

The building envelope is a principal responsible for buildings energy loses. Lime plasters as the most popular finishing materials of historical buildings and culture monuments influence the thermal behaviour as well as construction material of masonry. On this account, the effect of ageing on the thermophysical properties of a newly designed lime plasters containing hydrophobic admixture is analysed in the paper. For the comparative purposes, the reference lime plaster is tested. The ageing is accelerated with controlled carbonation process to simulate the final plasters properties. Basic characterization of the tested materials is done using bulk density, matrix density, and porosity measurements. Thermal conductivity and volumetric heat capacity are experimentally assessed using a transient impulse method. The obtained data revealed the significant changes of the both studied thermal parameters in the dependence on plasters composition and age. The assessed material parameters will be stored in a material database, where will find use as an input data for computational modelling of heat transport in this type of porous building materials and evaluation of energy-savings and sustainability issues.

A Comparative Evaluation of Mixed Dentition Analysis on Reliability of Cone Beam Computed Tomography Image Compared to Plaster Model

PubMed Central

Gowd, Snigdha; Shankar, T; Dash, Samarendra; Sahoo, Nivedita; Chatterjee, Suravi; Mohanty, Pritam

2017-01-01

Aims and Objective: The aim of the study was to evaluate the reliability of cone beam computed tomography (CBCT) obtained image over plaster model for the assessment of mixed dentition analysis. Materials and Methods: Thirty CBCT-derived images and thirty plaster models were derived from the dental archives, and Moyer's and Tanaka-Johnston analyses were performed. The data obtained were interpreted and analyzed statistically using SPSS 10.0/PC (SPSS Inc., Chicago, IL, USA). Descriptive and analytical analysis along with Student's t-test was performed to qualitatively evaluate the data and P < 0.05 was considered statistically significant. Results: Statistically, significant results were obtained on data comparison between CBCT-derived images and plaster model; the mean for Moyer's analysis in the left and right lower arch for CBCT and plaster model was 21.2 mm, 21.1 mm and 22.5 mm, 22.5 mm, respectively. Conclusion: CBCT-derived images were less reliable as compared to data obtained directly from plaster model for mixed dentition analysis. PMID:28852639

Synthesis of Plaster for moulers's elaboration of imprint denture

NASA Astrophysics Data System (ADS)

Hamiane, M.; Rabahi, N.; Saidi, M.; Salhi, M.

2012-02-01

Our goal was the synthesis of plaster from local raw materials to be used in denture mouler's. The plaster type α and β was synthesis by hydrothermal and dry method from gypsum (CaSO4. 2H2O) of the west Algerian. After crushing and mineralogical analysis, gypsum has undergone through cooking in an oven at a temperature (T = 200 ° C), for a time t = 4 hours. The synthesis and characterization of the product has involved several ways investigated as diffraction RX, X-ray fluorescence, time taken, electron microscope (MEB), hardness, SSB, compressive and bending strength and Ph. A digester horizontal type Toni - technical laboratory was used for the synthesis of plasterα. The results are conformable with the standard and plaster synthesized can be a basic material in the manufacture of moulers imprint denture.

Efficacy of betamethasone valerate medicated plaster on painful chronic elbow tendinopathy: a double-blind, randomized, placebo-controlled trial

PubMed Central

Frizziero, Antonio; Causero, Araldo; Bernasconi, Stefano; Papalia, Rocco; Longo, Mario; Sessa, Vincenzo; Sadile, Francesco; Greco, Pasquale; Tarantino, Umberto; Masiero, Stefano; Rovati, Stefano; Frangione, Valeria

2016-01-01

Summary Objective to investigate the efficacy and safety of a medicated plaster containing betamethasone valerate (BMV) 2.25 mg in patients with chronic elbow tendinopathy. Methods randomized, double-blind, placebo-controlled study with assignment 2:2:1:1 to BMV medicated plaster applied daily for 12 hours, daily for 24 hours or matched placebo. 62 patients aged ≥18 years with chronic lateral elbow tendinopathy were randomized. The primary efficacy variable was pain reduction (VAS) at day 28. Secondary objectives included summed pain intensity differences (SPID), overall treatment efficacy and tolerability. Results mean reduction in VAS pain score at day 28 was greater in both BMV medicated plaster groups, −39.35±27.69 mm for BMV12-h and −36.91±32.50 mm for BMV24-h, than with placebo, −20.20±27.32 mm. Considering the adjusted mean decreases, there was a statistically significant difference between BMV12-h and placebo (p=0.0110). Global pain relief (SPID) and overall treatment efficacy were significantly better with BMV. BMV and placebo plasters had similar local tolerability and there were few treatment-related adverse events. Conclusions BMV plaster was significantly more effective than placebo at reducing pain in patients with chronic elbow tendinopathies. The BMV plaster was safe and well tolerated. PMID:27331041

3-D Wizardry: Design in Papier-Mache, Plaster, and Foam.

ERIC Educational Resources Information Center

Wolfe, George

Papier-mache, plaster, and foam are inexpensive and versatile media for 3-dimensional classroom and studio art experiences. They can be used equally well by elementary, high school, or college students. Each medium has its own characteristic. Papier-mache is pliable but dries into a hard, firm surface that can be waterproofed. Plaster can be…

Populations of some molds in water-damaged homes may differ if the home was constructed with gypsum drywall compared to plaster

EPA Science Inventory

Starting in the 1940s, gypsum drywall began replacing plaster and lathe in the U.S. home construction industry. Our goal was to evaluate whether some mold populations differ in water- damaged homes primarily constructed with gypsum drywall compared to plaster. The dust samples fr...

Royal London space analysis: plaster versus digital model assessment.

PubMed

Grewal, Balpreet; Lee, Robert T; Zou, Lifong; Johal, Ama

2017-06-01

With the advent of digital study models, the importance of being able to evaluate space requirements becomes valuable to treatment planning and the justification for any required extraction pattern. This study was undertaken to compare the validity and reliability of the Royal London space analysis (RLSA) undertaken on plaster as compared with digital models. A pilot study (n = 5) was undertaken on plaster and digital models to evaluate the feasibility of digital space planning. This also helped to determine the sample size calculation and as a result, 30 sets of study models with specified inclusion criteria were selected. All five components of the RLSA, namely: crowding; depth of occlusal curve; arch expansion/contraction; incisor antero-posterior advancement and inclination (assessed from the pre-treatment lateral cephalogram) were accounted for in relation to both model types. The plaster models served as the gold standard. Intra-operator measurement error (reliability) was evaluated along with a direct comparison of the measured digital values (validity) with the plaster models. The measurement error or coefficient of repeatability was comparable for plaster and digital space analyses and ranged from 0.66 to 0.95mm. No difference was found between the space analysis performed in either the upper or lower dental arch. Hence, the null hypothesis was accepted. The digital model measurements were consistently larger, albeit by a relatively small amount, than the plaster models (0.35mm upper arch and 0.32mm lower arch). No difference was detected in the RLSA when performed using either plaster or digital models. Thus, digital space analysis provides a valid and reproducible alternative method in the new era of digital records. © The Author 2016. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com

Adhesive plasters

DOEpatents

Holcombe, Jr., Cressie E.; Swain, Ronald L.; Banker, John G.; Edwards, Charlene C.

1978-01-01

Adhesive plaster compositions are provided by treating particles of Y.sub.2 O.sub.3, Eu.sub.2 O.sub.3, Gd.sub.2 O.sub.3 or Nd.sub.2 O.sub.3 with dilute acid solutions. The resulting compositions have been found to spontaneously harden into rigid reticulated masses resembling plaster of Paris. Upon heating, the hardened material is decomposed into the oxide, yet retains the reticulated rigid structure.

Exterior building details of Building A; east façade: concrete staircase, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Exterior building details of Building A; east façade: concrete staircase, profiled cement, plaster door surround, recessed panel inscribed "1859", historic window opening with concrete sill above door, cement plaster dentil course and cornice truncated wood beam ends, plaster finished brick wall, granite base; westerly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

Digital model as an alternative to plaster model in assessment of space analysis

PubMed Central

Kumar, A. Anand; Phillip, Abraham; Kumar, Sathesh; Rawat, Anuradha; Priya, Sakthi; Kumaran, V.

2015-01-01

Introduction: Digital three-dimensional models are widely used for orthodontic diagnosis. The purpose of this study was to appraise the accuracy of digital models obtained from computer-aided design/computer-aided manufacturing (CAD/CAM) and cone-beam computed tomography (CBCT) for tooth-width measurements and the Bolton analysis. Materials and Methods: Digital models (CAD/CAM, CBCT) and plaster model were made for each of 50 subjects. Tooth-width measurements on the digital models (CAD/CAM, CBCT) were compared with those on the corresponding plaster models. The anterior and overall Bolton ratios were calculated for each participant and for each method. The paired t-test was applied to determine the validity. Results: Tooth-width measurements, anterior, and overall Bolton ratio of digital models of CAD/CAM and CBCT did not differ significantly from those on the plaster models. Conclusion: Hence, both CBCT and CAD/CAM are trustable and promising technique that can replace plaster models due to its overwhelming advantages. PMID:26538899

Can treatment success with 5% lidocaine medicated plaster be predicted in cancer pain with neuropathic components or trigeminal neuropathic pain?

PubMed Central

Kern, Kai-Uwe; Nalamachu, Srinivas; Brasseur, Louis; Zakrzewska, Joanna M

2013-01-01

An expert group of 40 pain specialists from 16 countries performed a first assessment of the value of predictors for treatment success with 5% lidocaine-medicated plaster in the management of cancer pain with neuropathic components and trigeminal neuropathic pain. Results were based on the retrospective analysis of 68 case reports (sent in by participants in the 4 weeks prior to the conference) and the practical experience of the experts. Lidocaine plaster treatment was mostly successful for surgery or chemotherapy-related cancer pain with neuropathic components. A dose reduction of systemic pain treatment was observed in at least 50% of all cancer pain patients using the plaster as adjunct treatment; the presence of allodynia, hyperalgesia or pain quality provided a potential but not definitively clear indication of treatment success. In trigeminal neuropathic pain, continuous pain, severe allodynia, hyperalgesia, or postherpetic neuralgia or trauma as the cause of orofacial neuropathic pain were perceived as potential predictors of treatment success with lidocaine plaster. In conclusion, these findings provide a first assessment of the likelihood of treatment benefits with 5% lidocaine-medicated plaster in the management of cancer pain with neuropathic components and trigeminal neuropathic pain and support conducting large, well-designed multicenter studies. PMID:23630431

A numerical study of defect detection in a plaster dome ceiling using structural acoustics.

PubMed

Bucaro, J A; Romano, A J; Valdivia, N; Houston, B H; Dey, S

2009-07-01

A numerical study is carried out to evaluate the effectiveness of using measured surface displacements resulting from acoustic speaker excitation to detect and localize flaws in a domed, plaster ceiling. The response of the structure to an incident acoustic pressure is obtained at four frequencies between 100 and 400 Hz using a parallel h-p structural acoustic finite element-based code. Three ceiling conditions are modeled: the pristine ceiling considered rigidly attached to the domed-shape support, partial detachment of a segment of the plaster layer from the support, and an interior pocket of plaster deconsolidation modeled as a heavy fluid. Spatial maps of the normal displacement resulting from speaker excitation are interpreted with the help of predictions based on static analysis. It is found that acoustic speaker excitation can provide displacement levels readily detected by commercially available laser Doppler vibrometer systems. Further, it is concluded that for 1 in. thick plaster layers, detachment sizes as small as 4 cm are detectable by direct observation of the measured displacement maps. Finally, spatial structure differences are observed in the displacement maps beneath the two defect types, which may provide a wavenumber-based feature useful for distinguishing plaster detachment from other defects such as deconsolidation.

Comparison of linear measurements and analyses taken from plaster models and three-dimensional images.

PubMed

Porto, Betina Grehs; Porto, Thiago Soares; Silva, Monica Barros; Grehs, Renésio Armindo; Pinto, Ary dos Santos; Bhandi, Shilpa H; Tonetto, Mateus Rodrigues; Bandéca, Matheus Coelho; dos Santos-Pinto, Lourdes Aparecida Martins

2014-11-01

Digital models are an alternative for carrying out analyses and devising treatment plans in orthodontics. The objective of this study was to evaluate the accuracy and the reproducibility of measurements of tooth sizes, interdental distances and analyses of occlusion using plaster models and their digital images. Thirty pairs of plaster models were chosen at random, and the digital images of each plaster model were obtained using a laser scanner (3Shape R-700, 3Shape A/S). With the plaster models, the measurements were taken using a caliper (Mitutoyo Digimatic(®), Mitutoyo (UK) Ltd) and the MicroScribe (MS) 3DX (Immersion, San Jose, Calif). For the digital images, the measurement tools used were those from the O3d software (Widialabs, Brazil). The data obtained were compared statistically using the Dahlberg formula, analysis of variance and the Tukey test (p < 0.05). The majority of the measurements, obtained using the caliper and O3d were identical, and both were significantly different from those obtained using the MS. Intra-examiner agreement was lowest when using the MS. The results demonstrated that the accuracy and reproducibility of the tooth measurements and analyses from the plaster models using the caliper and from the digital models using O3d software were identical.

Efficacy and Safety of Calcipotriol Plus Betamethasone Dipropionate Aerosol Foam Compared with Betamethasone 17-Valerate-Medicated Plaster for the Treatment of Psoriasis.

PubMed

Queille-Roussel, Catherine; Rosen, Monika; Clonier, Fabrice; Nørremark, Kasper; Lacour, Jean-Philippe

2017-04-01

Fixed combination calcipotriol as hydrate (Cal) 50 µg/g plus betamethasone as dipropionate (BD) 0.5 mg/g aerosol foam is an alcohol-free treatment for psoriasis. Betamethasone 17-valerate 2.25 mg (BV)-medicated plasters are recommended for treating psoriasis plaques localized in difficult-to-treat (DTT; elbow, knee, anterior face of the tibia) areas. The aim of this study was to compare the efficacy of Cal/BD foam with BV-medicated plaster in patients with plaque psoriasis. In this phase IIa, randomized, single-center, investigator-blinded, 4-week study, both Cal/BD foam and BV-medicated plaster were applied once daily to six test sites (three for each treatment). The primary efficacy endpoint was absolute change in total clinical score (TCS; sum of erythema, scaling, and infiltration); secondary endpoints were changes from baseline in each individual clinical score, ultrasonographic changes (total skin and echo-poor band thickness), and safety; and post hoc analysis was change from baseline in TCS on DTT areas. Thirty-five patients were included. Least-squares mean change in TCS from baseline was significantly greater for Cal/BD foam (-5.8) than BV-medicated plaster (-3.7; difference -2.2; 95% confidence interval -2.6 to -1.8; p < 0.001); greater changes for Cal/BD foam were observed from day 8 for each clinical sign. Absolute total skin and echo-poor band thickness change was significantly greater for Cal/BD foam than for BV-medicated plaster (both p < 0.001). Post hoc analyses showed that Cal/BD foam was significantly more effective than BV-medicated plaster on DTT areas after 4 weeks (p < 0.001), and both treatments were well tolerated. Cal/BD foam demonstrated superior efficacy versus BV-medicated plasters, including on DTT areas, in patients with plaque psoriasis. NCT02518048.

Seals, Concrete Anchors, and Connections

DTIC Science & Technology

1989-02-01

brick. Medium to heavy I.. loads cannot be safely fastened to soft masonry materials (stuc-. : - . co. grout. plaster or plasterboard ) since such...588C, Type 1. Class A. Style 1 Use in: All masonry material Use in: Block, wallboard , plaster , hollow tile Use with: Sheet metal, wood or lag screws... Wallboard . plaster , paneling Use in: Wallboard or solid masonry Use with: No (- oer fastener needed Use with: Sheet metal screw Made of: Ste( Made of

Adhesive plasters. [Patent application; coatings for crucibles, control rods, etc

DOEpatents

Holcombe, C.E. Jr.; Swain, R.L.; Banker, J.G.; Edwards, C.C.

1975-09-26

Adhesive plaster compositions are provided by treating particles of Y/sub 2/O/sub 3/, Eu/sub 2/O/sub 3/, Gd/sub 2/O/sub 3/, or Nd/sub 2/O/sub 3/ with dilute acid solutions. The resulting compositions were found to harden spontaneously into rigid reticulated masses resembling plaster of Paris. Upon heating, the hardened material is decomposed into the oxide, yet retains the reticulated rigid structure. 1 table.

Treatment of localized neuropathic pain of different etiologies with the 5% lidocaine medicated plaster – a case series

PubMed Central

Likar, Rudolf; Demschar, Susanne; Kager, Ingo; Neuwersch, Stefan; Pipam, Wolfgang; Sittl, Reinhard

2015-01-01

Objective To assess the efficacy and safety of the topical 5% lidocaine medicated plaster in the treatment of localized neuropathic pain. Study design This was a case series at an Austrian pain clinic, using retrospective analysis. Patients and methods Data of 27 patients treated for localized neuropathic pain with the 5% lidocaine medicated plaster were retrospectively analyzed. Assessment included changes in overall pain intensity, in intensity of different pain qualities, and of hyperalgesia and allodynia, and changes in sleep quality. Results Patients (17 female, ten male; mean age 53.4±11.4 years) presented mainly with dorsalgia (16 patients) or postoperative/posttraumatic pain (seven patients); one patient suffered from both. The mean overall pain intensity prior to treatment with lidocaine medicated plaster was 8.4±1.2 on the 11-point Likert scale. In the majority of cases, the lidocaine plaster was applied concomitantly with preexisting pain medication (81.5% of the patients). During the 6-month observation period, overall mean pain intensity was reduced by almost 5 points (4.98) to 3.5±2.6. Substantial reductions were also observed for neuralgiform pain (5 points from 7.9±2.6 at baseline) and burning pain (3 points from 5.2±4.1). Sleep quality improved from 4.6±2.6 at baseline to 5.5±1.8. Stratification by pain diagnosis showed marked improvements in overall pain intensity for patients with dorsalgia or postoperative/posttraumatic pain. The lidocaine plaster was well tolerated. Conclusion Overall, topical treatment with the 5% lidocaine medicated plaster was associated with effective pain relief and was well tolerated. PMID:25565882

Functional exercise in combination with auricular plaster therapy is more conducive to rehabilitation of menopausal women patients with anxiety disorder

PubMed Central

Han, Yubin; Duan, Fugui; Xu, Rongmei; Wang, Yi; Zhang, Hongyu

2015-01-01

Objective: Observe the effect of functional exercise in combination with auricular plaster therapy on menopausal women patients with anxiety disorder. Method: Select 45 menopausal women patients with anxiety disorder and then adopt random digital table to divide them into a functional exercise group, an auricular plaster therapy group and a combination group. Each group consists of 15 patients. The patients in the functional exercise group do yoga exercise twice a day; those in the auricular plaster therapy group are provided with the auricular plaster therapy twice a day; those in the combination group do yoga exercise and then they are provided with the auricular plaster therapy twice a day. Before the treatment and after 12 weeks’ treatment, respectively detect and compare the selected patients in the three groups in respect HAMA score, physical function score and mental function score; And the cured patients are followed up for 3 months to compare recurrence rate of each group. Results: After 12 weeks’ treatment, HAMA score, physical function score and mental function score of the combination group are obviously better than those of another two groups (P<0.05); Of the cure rate and the recurrence rate within 3 months, the cure rate of the combination group is higher and the recurrence rate is low. Conclusion: Through the functional rehabilitation exercise in combination with the auricular plaster, the combined curative effect is obviously better than that of single treatment and the clinical recurrence rate is significantly lower than that of single treatment. It shows that the combined treatment method presents obvious synergistic effect and the synergistic treatment is more beneficial to improve the curative effect. PMID:26885051

Analysis of wall plasters and natural sediments from the Neolithic town of Çatalhöyük (Turkey) by a range of analytical techniques

NASA Astrophysics Data System (ADS)

Anderson, Emma; Almond, Matthew J.; Matthews, Wendy

2014-12-01

Wall plaster sequences from the Neolithic town of Çatalhöyük have been analysed and compared to three types of natural sediment found in the vicinity of the site, using a range of analytical techniques. Block samples containing the plaster sequences were removed from the walls of several different buildings on the East Mound. Sub-samples were examined by IR spectroscopy, X-ray diffraction and X-ray fluorescence to determine the overall mineralogical and elemental composition, whilst thin sections were studied using optical polarising microscopy, IR Microscopy and Environmental Scanning Electron Microscopy with Energy Dispersive X-ray analysis. The results of this study have shown that there are two types of wall plaster found in the sequences and that the sediments used to produce these were obtained from at least two distinct sources. In particular, the presence of clay, calcite and magnesian calcite in the foundation plasters suggested that these were prepared predominantly from a marl source. On the other hand, the finishing plasters were found to contain dolomite with a small amount of clay and no calcite, revealing that softlime was used in their preparation. Whilst marl is located directly below and around Çatalhöyük, the nearest source of softlime is 6.5 km away, an indication that the latter was important to the Neolithic people, possibly due to the whiter colour (5Y 8/1) of this sediment. Furthermore, the same two plaster types were found on each wall of Building 49, the main building studied in this research, and in all five buildings investigated, suggesting that the use of these sources was an established practice for the inhabitants of several different households across the site.

Prediction Model for Impulsive Noise on Structures

DTIC Science & Technology

2012-09-01

construction usually have an interior wall finish of: a) gypsum wallboard (also called plasterboard or drywall), b) plaster or c) wood paneling... Gypsum Plaster , Wall Board 11,67 0.04 NA For simply-supported beams vibrating in their fundamental mode, the value of KS is needed for...Dev of log10(f0) for wood panel interior to be average for wood walls with plaster or gypsum board interior. (8) L(w) based on estimated standard

Studies on use of Copper Slag as Replacement Material for River Sand in Building Constructions

NASA Astrophysics Data System (ADS)

Madheswaran, C. K.; Ambily, P. S.; Dattatreya, J. K.; Rajamane, N. P.

2014-09-01

This work focuses on the use of copper slag, as a partial replacement of sand for use in cement concrete and building construction. Cement mortar mixtures prepared with fine aggregate made up of different proportions of copper slag and sand were tested for use as masonry mortars and plastering. Three masonry wall panels of dimensions 1 × 1 m were plastered. The studies showed that although copper slag based mortar is suitable for plastering, with the increase in copper slag content, the wastage due to material rebounding from the plastered surfaces increases. It is therefore suggested that the copper slag can be used for plastering of floorings and horizontal up to 50 % by mass of the fine aggregate, and for vertical surfaces, such as, brick/block walls it can be used up to 25 %. In this study on concrete mixtures were prepared with two water cement ratios and different proportions of copper slag ranging from 0 % (for the control mix) to 100 % of fine aggregate. The Concrete mixes were evaluated for workability, density, and compressive strength.

[The effect of curiozin gel and adhesive plaster application on the healing and blood flow dynamics in skin autografts from various areas of body in rats].

PubMed

Zadorozhnyĭ, A A; Shtrygol', S Iu; Kataev, S I

2004-01-01

The stimulating effect of curiozin gel and plaster application on the engraftment of skin autografts from various areas of body was studied in rats. Curiozin gel in a single dose of 75 mg was used for the daily treatment of autografts over the entire postoperation period of time. The adhesive plaster was applied onto skin autografts for 5 days after skin transplantation. The skin autografts in the test group exhibited normalized volume blood flow dynamics, reduced duration of the inflammatory reaction, and improved the quality of engraftment as compared to the untreated control group. The best healing and blood-flow-normalizing effect was achieved by combined application of curiozin gel and adhesive plaster.

Technological Characterization of Wall Paintings from the A Mithraic Tomb Dated to 4th-5th Century AD, Gargaresc, Libya

NASA Astrophysics Data System (ADS)

Abd El Salam, S.; Maniatis, Y.

2009-04-01

The excavations of Gargaresc started in 1965 and were one of the most important archaeological sites in Tripoli because it includes a period of about 500 years starting from the 1stc. AD was and continuing until the 5th century AD. The Mithraic tomb is one of the most important outlying monuments of Oea, 200 yards south of the western end of Gargaresc oasis, on the left of the Tripoli-Zuara road between kilometers 5 & 6. The tomb is cut in an outcrop of soft sandstone. The wall paintings found were symbolic to the religion of that period; which contained a mixture of older religions and Christian, and presented the interaction between the artistic and religious elements of that time. Several optical, chemical and mineralogical methods were applied to identify the materials, composition and technology of the plasters and mortars, as well as, the pigments used in the tomb. These are: -OP: Optical microscopy was used as the initial examination of polished cross-sections to identify the structure and microstratigraphy of the plasters and mortars as well as the painted layers. -MCT: Micro-chemical tests were used to identify the type of the plasters and mortars- calcium aluminium silicate and water-soluble salt to identify sulphates, chlorides, carbonates, nitrites and nitrates. -SM: Standard methods for chemical analysis to identify the quantitative and qualitative nature of the plasters and mortars and their mixture. -SEM & EDS: Analytical Scanning electron microscope with energy dispersive x-ray analysis system to examine the micrmorphology and determine the chemical composition of the plasters, pigments and the inclusions. -XRD: X-ray powder diffraction to identify the mineralogical composition of the plasters, mortars and pigments. On the bases of all the data obtained, it was possible to establish the nature of the plasters, mortars and their binder. The examination and analysis gave a full picture about the materials and the approximate ratio of amount of additives to lime used for making the mortars and plasters. In addition the results showed the stratigraphy of the various layers applied. The lime plasters and mortars contained apart from lime as binder quartz grains, charcoal, ironstone, brick and some other inclusions. Furthermore the mineralogical analysis provided information on the main mineralogical phases present in the plasters and pigments. The use of gypsum was detected in some cases but it was identified as a result of conservation. The analytical results provided also information on the deterioration factors and alterations that have affected the materials of the wall paintings and present quite interesting challenges for conservation science.

Agreement in the determination of preformed wire shape templates on plaster models and customized digital arch form diagrams on digital models.

PubMed

Camardella, Leonardo Tavares; Sá, Maiara da Silva Bezerra; Guimarães, Luciana Campos; Vilella, Beatriz de Souza; Vilella, Oswaldo de Vasconcellos

2018-03-01

The aim of this study was to verify the accuracy of preformed wire shape templates on plaster models and those of customized digital arch form diagrams on digital models. Twenty pairs of dental plaster models were randomly selected from the archives of the Department of Orthodontics of Federal Fluminense University, Niterói, Rio de Janeiro, Brazil. All plaster model samples were scanned in a plaster model scanner to create the respective digital models. Three examiners defined the arch form on the mandibular arch of these models by selecting the ideal preformed wire shape template on each plaster model or by making a customized digital arch form on the digital models using a digital arch form customization tool. These 2 arch forms were superimposed by the best-fit method. The greatest differences in the 6 regions on the superimposed arches were evaluated. Each examiner presented a descriptive analysis with the means, standard deviation, and minimum and maximum intervals of the differences on the superimpositions. Intraclass correlation coefficient and paired t tests were used to evaluate the accuracy of the superimpositions. Among the 6 regions analyzed in the superimpositions, the largest differences in the anterior and premolar regions were considered clinically insignificant, whereas the largest differences in the right molar region, especially the second molar area, were considered clinically significant by all 3 examiners. The intraclass correlation coefficients showed a weak correlation in the premolar region and moderate correlations in the anterior and molar regions. The paired t test showed statistically significant differences in the left anterior and premolar regions. The superimpositions between the arch forms on plaster and digital models were considered accurate, and the differences were not clinically significant, with the exception of the second molar area. Despite the favorable results, the requirement of correcting some software problems may hamper the transition from plaster to digital models. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Factors contributing to the temperature beneath plaster or fiberglass cast material

PubMed Central

Hutchinson, Michael J; Hutchinson, Mark R

2008-01-01

Background Most cast materials mature and harden via an exothermic reaction. Although rare, thermal injuries secondary to casting can occur. The purpose of this study was to evaluate factors that contribute to the elevated temperature beneath a cast and, more specifically, evaluate the differences of modern casting materials including fiberglass and prefabricated splints. Methods The temperature beneath various types (plaster, fiberglass, and fiberglass splints), brands, and thickness of cast material were measured after they were applied over thermometer which was on the surface of a single diameter and thickness PVC tube. A single layer of cotton stockinette with variable layers and types of cast padding were placed prior to application of the cast. Serial temperature measurements were made as the cast matured and reached peak temperature. Time to peak, duration of peak, and peak temperature were noted. Additional tests included varying the dip water temperature and assessing external insulating factors. Ambient temperature, ambient humidity and dip water freshness were controlled. Results Outcomes revealed that material type, cast thickness, and dip water temperature played key roles regarding the temperature beneath the cast. Faster setting plasters achieved peak temperature quicker and at a higher level than slower setting plasters. Thicker fiberglass and plaster casts led to greater peak temperature levels. Likewise increasing dip-water temperature led to elevated temperatures. The thickness and type of cast padding had less of an effect for all materials. With a definition of thermal injury risk of skin injury being greater than 49 degrees Celsius, we found that thick casts of extra fast setting plaster consistently approached dangerous levels (greater than 49 degrees for an extended period). Indeed a cast of extra-fast setting plaster, 20 layers thick, placed on a pillow during maturation maintained temperatures over 50 degrees of Celsius for over 20 minutes. Conclusion Clinicians should be cautious when applying thick casts with warm dip water. Fast setting plasters have increased risk of thermal injury while brand does not appear to play a significant role. Prefabricated fiberglass splints appear to be safer than circumferential casts. The greatest risk of thermal injury occurs when thick casts are allowed to mature while resting on pillow. PMID:18298851

Plaster core washout tool

NASA Technical Reports Server (NTRS)

Heisman, R. M.; Keir, A. R.; Teramura, K.

1977-01-01

Tool powered by pressurized water or air removes water soluble plaster lining from Kevlar/epoxy duct. Rotating plastic cutterhead with sealed end fitting connects flexible shaft that allows tool to be used with curved ducts.

Gray level co-occurrence and random forest algorithm-based gender determination with maxillary tooth plaster images.

PubMed

Akkoç, Betül; Arslan, Ahmet; Kök, Hatice

2016-06-01

Gender is one of the intrinsic properties of identity, with performance enhancement reducing the cluster when a search is performed. Teeth have durable and resistant structure, and as such are important sources of identification in disasters (accident, fire, etc.). In this study, gender determination is accomplished by maxillary tooth plaster models of 40 people (20 males and 20 females). The images of tooth plaster models are taken with a lighting mechanism set-up. A gray level co-occurrence matrix of the image with segmentation is formed and classified via a Random Forest (RF) algorithm by extracting pertinent features of the matrix. Automatic gender determination has a 90% success rate, with an applicable system to determine gender from maxillary tooth plaster images. Copyright © 2016 Elsevier Ltd. All rights reserved.

[The reliability of dento-maxillary models created by cone-beam CT and rapid prototyping:a comparative study].

PubMed

Lv, Yan; Yan, Bin; Wang, Lin; Lou, Dong-hua

2012-04-01

To analyze the reliability of the dento-maxillary models created by cone-beam CT and rapid prototyping (RP). Plaster models were obtained from 20 orthodontic patients who had been scanned by cone-beam CT and 3-D models were formed after the calculation and reconstruction of software. Then, computerized composite models (RP models) were produced by rapid prototyping technique. The crown widths, dental arch widths and dental arch lengths on each plaster model, 3-D model and RP model were measured, followed by statistical analysis with SPSS17.0 software package. For crown widths, dental arch lengths and crowding, there were significant differences(P<0.05) among the 3 models, but the dental arch widths were on the contrary. Measurements on 3-D models were significantly smaller than those on other two models(P<0.05). Compared with 3-D models, RP models had more numbers which were not significantly different from those on plaster models(P>0.05). The regression coefficient among three models were significantly different(P<0.01), ranging from 0.8 to 0.9. But between RP and plaster models was bigger than that between 3-D and plaster models. There is high consistency within 3 models, while some differences were accepted in clinic. Therefore, it is possible to substitute 3-D and RP models for plaster models in order to save storage space and improve efficiency.

The application of multi-baseline digital close-range photogrammetry in three-dimensional imaging and measurement of dental casts.

PubMed

Fu, Xiaoming; Peng, Chun; Li, Zan; Liu, Shan; Tan, Minmin; Song, Jinlin

2017-01-01

To explore a new technique for reconstructing and measuring three-dimensional (3D) models of orthodontic plaster casts using multi-baseline digital close-range photogrammetry (MBDCRP) with a single-lens reflex camera. Thirty sets of orthodontic plaster casts that do not exhibit severe horizontal overlap (>2 mm) between any two teeth were recorded by a single-lens reflex camera with 72 pictures taken in different directions. The 3D models of these casts were reconstructed and measured using the open source software MeshLab. These parameters, including mesio-distal crown diameter, arch width, and arch perimeter, were recorded six times on both the 3D digital models and on plaster casts by two examiners. Statistical analysis was carried out using the Bland-Altman method to measure agreement between the novel method and the traditional calliper method by calculating the differences between mean values. The average differences between the measurements of the photogrammetric 3D models and the plaster casts were 0.011-0.402mm. The mean differences between measurements obtained by the photogrammetric 3D models and the dental casts were not significant except for the lower arch perimeter (P>0.05), and all the differences were regarded as clinically acceptable (<0.5 mm). Measurements obtained by MBDCRP are compared well with those obtained from plaster casts, indicating that MBDCRP is an alternate way to store and measure dental plaster casts without severe horizontal overlap between any two teeth.

Plaster-Wrap Dragons

ERIC Educational Resources Information Center

Vance, Shelly

2012-01-01

In this article, the author describes how her students constructed a three-dimensional sculpture of a dragon using plaster wrap and other materials. The dragons were formed from modest means--using only a toilet-paper tube, newsprint, tape and wire.

Archaeomagnetic studies in central Mexico—dating of Mesoamerican lime-plasters

NASA Astrophysics Data System (ADS)

Hueda-Tanabe, Y.; Soler-Arechalde, A. M.; Urrutia-Fucugauchi, J.; Barba, L.; Manzanilla, L.; Rebolledo-Vieyra, M.; Goguitchaichvili, A.

2004-11-01

For the first time results of an archaeomagnetic study of unburned lime-plasters from Teotihuacan and Tenochtitlan in central Mesoamerica are presented. Plasters made of lime, lithic clasts and water, appear during the Formative Period and were used for a variety of purposes in floors, sculptures, ceramics and supporting media for mural paintings in the Oaxaca and Maya area. In Central Mexico, grinded volcanic scoria rich in iron minerals is incorporated into the lime-plasters mixture. Samples were selected from two archaeological excavation projects in the Teopancazco residential compound of Teotihuacan and the large multi-stage structure of Templo Mayor in Tenochtitlan, where chronological information is available. The intensity of remanent magnetization (natural remanent magnetization (NRM)) and low-field susceptibility are weak reflecting low relative content of magnetic minerals. NRM directions are well grouped and alternating field demagnetization shows single or two-component magnetizations. Rockmagnetic experiments point to fine-grained titanomagnetites with pseudo-single domain behavior. Anisotropy of magnetic susceptibility (AMS) measurements document a depositional fabric, with normal to free-surface minimum AMS axes. Characteristic mean site directions were correlated to the paleosecular variation curve for Mesoamerica. Data from Templo Mayor reflect recent tilting of the structures. Teopancazco mean site declinations show good correspondence with the reference curve, in agreement with the radiocarbon dating. Dates for four stages of Teotihuacan occupancy based on the study of lime-plasters range from AD 350 to 550. A date for a possible Mazapa occupation around AD 850 or 950 is also suggested based on the archaeomagnetic correlation. The archaeomagnetic record of a plaster floor in Teopancazco differed from the other nearby sites pointing to a thermoremanent magnetization; comparison with the reference curve suggests dates around AD 1375 or 1415. The burning of the stucco floor likely occurred during a late re-occupation of the site by the Aztecs. Our results suggest that archaeomagnetic dating can be applied to lime-plasters, which are materials widely employed in Mesoamerica.

Analysis of wall plasters and natural sediments from the Neolithic town of Çatalhöyük (Turkey) by a range of analytical techniques.

PubMed

Anderson, Emma; Almond, Matthew J; Matthews, Wendy

2014-12-10

Wall plaster sequences from the Neolithic town of Çatalhöyük have been analysed and compared to three types of natural sediment found in the vicinity of the site, using a range of analytical techniques. Block samples containing the plaster sequences were removed from the walls of several different buildings on the East Mound. Sub-samples were examined by IR spectroscopy, X-ray diffraction and X-ray fluorescence to determine the overall mineralogical and elemental composition, whilst thin sections were studied using optical polarising microscopy, IR Microscopy and Environmental Scanning Electron Microscopy with Energy Dispersive X-ray analysis. The results of this study have shown that there are two types of wall plaster found in the sequences and that the sediments used to produce these were obtained from at least two distinct sources. In particular, the presence of clay, calcite and magnesian calcite in the foundation plasters suggested that these were prepared predominantly from a marl source. On the other hand, the finishing plasters were found to contain dolomite with a small amount of clay and no calcite, revealing that softlime was used in their preparation. Whilst marl is located directly below and around Çatalhöyük, the nearest source of softlime is 6.5km away, an indication that the latter was important to the Neolithic people, possibly due to the whiter colour (5Y 8/1) of this sediment. Furthermore, the same two plaster types were found on each wall of Building 49, the main building studied in this research, and in all five buildings investigated, suggesting that the use of these sources was an established practice for the inhabitants of several different households across the site. Copyright © 2014 Elsevier B.V. All rights reserved.

Outcomes of Pin and Plaster Versus Locking Plate in Distal Radius Intraarticular Fractures

PubMed Central

Bahari-Kashani, Mahmoud; Taraz-Jamshidy, Mohammad Hosein; Rahimi, Hassan; Ashraf, Hami; Mirkazemy, Masoud; Fatehi, Amirreza; Asadian, Mariam; Rezazade, Jafar

2013-01-01

Background Distal radius fractures are among the most prevalent fractures predictive of probable occurrence of other osteoporotic fractures. They are treated via a variety of methods, but the best treatment has not been defined yet. Objectives This study was performed to compare the results of open reduction and internal fixation with locking plates versus the pin and plaster method. Materials and Methods In this prospective study, 114 patients aged 40 to 60 years with Fernandez type III fracture referring to Imam-Reza and Mehr hospitals of Mashhad from 2009 to 2011, were selected randomly; after obtaining informed consent, they were treated with pin and plaster fixation (n = 57) or internal fixation with the volar locking plate (n = 57). They were compared at the one year follow up. Demographic features and standard radiographic indices were recorded and MAYO, DASH and SF - 36 tests were performed. Data was analyzed by SPSS software version 13, with descriptive indices, Mann-Whitney and Chi-square tests. Results SF-36 test demonstrated a better general health (P < 0.001), mental health (P = 0.006), physical functioning (P < 0.001), social functioning (P < 0.001) and energy/fatigue (P < 0.001) in LCP group. However, pain (P = 0.647) was not significantly different between the groups. Physical limitation (P < 0.001) and emotional limitation (P < 0.001) were greater in the pin and plaster group. Also, in the LCP group mean MAYO score (P < 0.001) was more than pin and plaster group. Mean DASH score was not different between the groups (P = 0.218). The rate of acceptable results of radiographic indices (P < 0.001), grip strength (P < 0.001) and range of motion in supination-pronation (P < 0.001) in LCP method were better than the pin and plaster method. Conclusions In treatment of intra-articular distal radius fractures in middle-aged patients internal fixation with locking plates may be prefered to pin and plaster as the treatment of choice. PMID:24350132

Asbestos in Plaster and Wall Systems

EPA Pesticide Factsheets

This collection of letters and clarification on final rules provides guidance on Asbestos National Emissions Standard for Hazardous Air Pollutants for asbestos-containing join compounds, and asbestos-containing materials found in plaster and wall systems.

37. PRESSING TILES FROM PLASTER MOLDS, USING A HAND PRESS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

37. PRESSING TILES FROM PLASTER MOLDS, USING A HAND PRESS CONSTRUCTED IN 1986. - Moravian Pottery & Tile Works, Southwest side of State Route 313 (Swamp Road), Northwest of East Court Street, Doylestown, Bucks County, PA

Hygrothermal analysis of surface layers of historical masonry

NASA Astrophysics Data System (ADS)

Kočí, Václav; Maděra, Jiří; Keppert, Martin; Černý, Robert

2017-11-01

The paper deals with the hygrothermal analysis of surface layers of historical masonry. Solid brick provided with a traditional and two modified lime-based plasters is studied. The heat and moisture transport in the envelope is induced by an exposure of the wall from the exterior side to dynamic climatic conditions of Olomouc, Czech Republic. The transport processes are described using diffusion type of mathematical model based on experimentally determined material properties. The computational results indicate that hygric transport and accumulation properties of exterior plasters affect the hygrothermal performance of the underlying solid brick in a very significant way, being able to regulate the amount of transported moisture. The modified lime plasters are not found generally superior to the traditional lime plasters in that respect. Therefore, their suitability for historical masonry should be assessed case by case, with a particular attention to the climatic conditions and to the properties of the load bearing structure.

Chemical and mineralogical characterization of archaeologicam building materials from Seyitomer Hoyuk Kutahya, Turkey.

NASA Astrophysics Data System (ADS)

Bilgen, Nejat; Olgun, Asim

This paper focuses on the spectroscopic and thermal analysis of the archaeological samples of mortar and plaster from middle Bronze Age and Achaemenid period in Seyitömer Höyük. The composition of the samples was investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and thermogravimetric thermal analysis (TG-DTA). The results showed that human used different types of raw materials in the preperation of the mortar and plaster in the Middle Bronze Age and Achaemenid period. The material used in middle Bronze Age contains muscovite whereas the material in Achaemenid period contains albite. Although, the chemical composition of the mortar and plaster used in the period were similar, the calcium content of the plaster is relatively higher than the one of the mortar indicating people's awareness of the binding properties of calcite.

The application of multi-baseline digital close-range photogrammetry in three-dimensional imaging and measurement of dental casts

PubMed Central

Li, Zan; Liu, Shan; Tan, Minmin; Song, Jinlin

2017-01-01

Objective To explore a new technique for reconstructing and measuring three-dimensional (3D) models of orthodontic plaster casts using multi-baseline digital close-range photogrammetry (MBDCRP) with a single-lens reflex camera. Study design Thirty sets of orthodontic plaster casts that do not exhibit severe horizontal overlap (>2 mm) between any two teeth were recorded by a single-lens reflex camera with 72 pictures taken in different directions. The 3D models of these casts were reconstructed and measured using the open source software MeshLab. These parameters, including mesio-distal crown diameter, arch width, and arch perimeter, were recorded six times on both the 3D digital models and on plaster casts by two examiners. Statistical analysis was carried out using the Bland–Altman method to measure agreement between the novel method and the traditional calliper method by calculating the differences between mean values. Results The average differences between the measurements of the photogrammetric 3D models and the plaster casts were 0.011–0.402mm. The mean differences between measurements obtained by the photogrammetric 3D models and the dental casts were not significant except for the lower arch perimeter (P>0.05), and all the differences were regarded as clinically acceptable (<0.5 mm). Conclusions Measurements obtained by MBDCRP are compared well with those obtained from plaster casts, indicating that MBDCRP is an alternate way to store and measure dental plaster casts without severe horizontal overlap between any two teeth. PMID:28640827

14. DETAIL OF SOUTHWEST FRONT OF WAREHOUSE, SHOWING CORRUGATED PLASTER/ASBESTOS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. DETAIL OF SOUTHWEST FRONT OF WAREHOUSE, SHOWING CORRUGATED PLASTER/ASBESTOS WALLS, WINDOWS AND ROOF. VIEW TO NORTHEAST. - Commercial & Industrial Buildings, International Harvester Company Showroom, Office & Warehouse, 10 South Main Street, Dubuque, Dubuque County, IA

A Fresco Sampler.

ERIC Educational Resources Information Center

Leshnoff, Susan K.

1990-01-01

Describes how third grade students learned about fresco paintings in Pompeii and made their own frescoes by pouring plaster into styrofoam trays and painting the surface. Students discovered they could control the paint better because of the porous surface of the plaster. (KM)

Plaster, Portraits and Pots.

ERIC Educational Resources Information Center

Schimsky, Marc

1982-01-01

Describes an art activity in which junior high school students make portrait pots using plaster casts and clay. Each student created a reflection of his or her personality in clay. Specific teaching methods and ways of working with materials are discussed. (AM)

Treatment of unicameral bone cysts by curettage and packing with plaster-of-Paris pellets. 1978.

PubMed

Peltier, Leonard F; Jones, Richard H

2004-05-01

Long-term follow-up of twenty-six patients with unicameral bone cysts treated by curettage and packing with plaster-of-Paris pellets showed a recurrence in only two cases and no serious complications.

The comparative risk of developing postoperative complications in patients with distal radius fractures following different treatment modalities

PubMed Central

Qiu, Wen-Jun; Li, Yi-Fan; Ji, Yun-Han; Xu, Wei; Zhu, Xiao-Dong; Tang, Xian-Zhong; Zhao, Huan-Li; Wang, Gui-Bin; Jia, Yue-Qing; Zhu, Shi-Cai; Zhang, Feng-Fang; Liu, Hong-Mei

2015-01-01

In this study, we performed a network meta-analysis to compare the outcomes of seven most common surgical procedures to fix DRF, including bridging external fixation, non-bridging external fixation, K-wire fixation, plaster fixation, dorsal plating, volar plating, and dorsal and volar plating. Published studies were retrieved through PubMed, Embase and Cochrane Library databases. The database search terms used were the following keywords and MeSH terms: DRF, bridging external fixation, non-bridging external fixation, K-wire fixation, plaster fixation, dorsal plating, volar plating, and dorsal and volar plating. The network meta-analysis was performed to rank the probabilities of postoperative complication risks for the seven surgical modalities in DRF patients. This network meta-analysis included data obtained from a total of 19 RCTs. Our results revealed that compared to DRF patients treated with bridging external fixation, marked differences in pin-track infection (PTI) rate were found in patients treated with plaster fixation, volar plating, and dorsal and volar plating. Cluster analysis showed that plaster fixation is associated with the lowest probability of postoperative complication in DRF patients. Plaster fixation is associated with the lowest risk for postoperative complications in DRF patients, when compared to six other common DRF surgical methods examined. PMID:26549312

24. Historic American Buildings Survey, W. Jeter Eason Deputy District ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. Historic American Buildings Survey, W. Jeter Eason- Deputy District Officer, Photographer November 21, 1936 PLASTER ORNAMENT ON CEILING AND PLASTER CORNICE BACK PARLOR (FRONT PARLOR SIMLAR). - The Hermitage, U.S. Highway 70 North (4580 Rachel's Lane), Nashville, Davidson County, TN

Abstract Sculptures: Wire and Plaster Cloth Creations.

ERIC Educational Resources Information Center

Hiller, Peter

2001-01-01

Presents a three-dimensional art project for middle-school students in which they create sculptures of plaster cloth and wire. The introduction explains that they learn about Alexander Calder, a master of using wire in art. Discusses how to make the sculptures. (CMK)

Characteristics, resource utilization and safety profile of patients prescribed with neuropathic pain treatments: a real-world evidence study on general practices in Europe - the role of the lidocaine 5% medicated plaster.

PubMed

Katz, Pablo; Pegoraro, Valeria; Liedgens, Hiltrud

2017-08-01

To identify characteristics, resource utilization, and safety profile of patients prescribed with lidocaine 5% medicated plaster, pregabalin, gabapentin, amitriptyline and duloxetine when experiencing pain in the real-world setting of general practitioners (GPs) in Europe. Retrospective analysis on real world data from IMS Health Longitudinal Patient Database. Patients with at least one prescription of the drugs of interest during 2014 were selected and those with a non-neuropathic pain-related diagnosis were excluded. Patients' demographic and clinical characteristics, resource utilization data and adverse drug reactions (ADRs) as described in the leaflet were extracted. The association between treatments and ADR occurrence was evaluated applying multivariate logistic models. A total of 70,515 patients were selected from Italy, Germany, the UK, Spain and Belgium. Lidocaine 5% medicated plaster patients were the oldest in Italy, the UK and Spain and the most health impaired in Italy, Spain and Belgium. No relevant differences in the number of co-prescriptions, specialist visits, examinations and hospitalizations were found. Significantly less lidocaine 5% plasters patients experienced ADRs, with odds ratios in favor of lidocaine 5% medicated plasters ranging from 3.41 (p = .036) to 52.33 (p < .001). Evidence from daily clinical practice in GP settings agrees with the findings from more controlled clinical-trial settings, with lidocaine 5% medicated plaster patients showing a better safety profile, but also a comparable level of resource utilization. A possible re-evaluation of the scientific value coming from this retrospective study in building up a diagnostic as well as a therapeutic algorithm is suggested.

Multidisciplinary approach to improve the quality of below-knee plaster casting.

PubMed

Williams, John Teudar; Kedrzycki, Marta; Shenava, Yathish

2018-01-01

In our trauma unit, we noted a high rate of incorrectly applied below-knee casts for ankle fractures, in some cases requiring reapplication. This caused significant discomfort and inconvenience for patients and additional burden on plaster-room services. Our aim was to improve the quality of plaster casts and reduce the proportion that needed to be reapplied. Our criteria for plaster cast quality were based on the British Orthopaedic Association Casting Standards (2015) and included neutral (plantargrade) ankle position, adequacy of fracture reduction and rate of cast reapplication. Baseline data collection was performed over a 2-month period by two independent reviewers. After distributing findings and presenting to relevant departments, practical casting sessions with orthopaedic technicians were arranged for the multidisciplinary team responsible for casting. This was later supplemented by new casting guidelines in clinical areas and available online. Postintervention data collection was performed over two separate cycles to assess the effect and permanence of intervention. Data from the preintervention period (n=29) showed median ankle position was 32° plantarflexion (PF), with nine (31%) inadequate reductions and six (20%) backslabs reapplied. Following Plan-Do-Study-Act (PDSA) 1, ankle position was significantly improved (median 25° PF), there were fewer inadequate reductions (12%; 2/17) and a lower rate of reapplication (0%; 0/17). After PDSA 2 (n=16), median ankle position was 21° PF, there was one (6%) inadequate reduction and two (12%) reapplications of casts. Following implementation of plaster training sessions for accident and emergency and junior orthopaedic staff, in addition to publishing guidance and new protocol, there has been a sustained improvement in the quality of below-knee backslabs and fewer cast reapplications. These findings justify continuation and expansion of the current programme to include other commonly applied plaster casts.

Sculpting Ceramic Heads.

ERIC Educational Resources Information Center

Sapiro, Maurice

1983-01-01

Clay sculpture is difficult to produce because of the requirements of kiln firing. The problems can be overcome by modeling the original manikin head and making a plaster mold, pressing molding slabs of clay into the plaster mold to form the hollow clay armature, and sculpting on the armature. (IS)

Utilization of ground waste seashells in cement mortars for masonry and plastering.

PubMed

Lertwattanaruk, Pusit; Makul, Natt; Siripattarapravat, Chalothorn

2012-11-30

In this research, four types of waste seashells, including short-necked clam, green mussel, oyster, and cockle, were investigated experimentally to develop a cement product for masonry and plastering. The parameters studied included water demand, setting time, compressive strength, drying shrinkage and thermal conductivity of the mortars. These properties were compared with those of a control mortar that was made of a conventional Portland cement. The main parameter of this study was the proportion of ground seashells used as cement replacement (5%, 10%, 15%, or 20% by weight). Incorporation of ground seashells resulted in reduced water demand and extended setting times of the mortars, which are advantages for rendering and plastering in hot climates. All mortars containing ground seashells yielded adequate strength, less shrinkage with drying and lower thermal conductivity compared to the conventional cement. The results indicate that ground seashells can be applied as a cement replacement in mortar mixes and may improve the workability of rendering and plastering mortar. Copyright © 2012 Elsevier Ltd. All rights reserved.

Computational modeling of latent-heat-storage in PCM modified interior plaster

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fořt, Jan; Maděra, Jiří; Trník, Anton

2016-06-08

The latent heat storage systems represent a promising way for decrease of buildings energy consumption with respect to the sustainable development principles of building industry. The presented paper is focused on the evaluation of the effect of PCM incorporation on thermal performance of cement-lime plasters. For basic characterization of the developed materials, matrix density, bulk density, and total open porosity are measured. Thermal conductivity is accessed by transient impulse method. DSC analysis is used for the identification of phase change temperature during the heating and cooling process. Using DSC data, the temperature dependent specific heat capacity is calculated. On themore » basis of the experiments performed, the supposed improvement of the energy efficiency of characteristic building envelope system where the designed plasters are likely to be used is evaluated by a computational analysis. Obtained experimental and computational results show a potential of PCM modified plasters for improvement of thermal stability of buildings and moderation of interior climate.« less

Atomic Oxygen Cleaning of Unpainted Plaster Sculptures

NASA Technical Reports Server (NTRS)

Banks, Bruce A.; Miller, Sharon K.

2017-01-01

Atomic oxygen erosion of polymers has been found to be a threat to spacecraft in low Earth orbit. As a result ground facilities have been developed to identify coatings to protect polymers such as used for solar array blankets. As a result of extensive laboratory testing, it was discovered that soot and other organic contamination on paintings could be readily removed by atomic oxygen interactions with minimal damage to the artwork. No method, other than dusting, has been found to be effective in the cleaning of unpainted plaster sculptures This presentation discusses the atomic oxygen interaction processes and how effective they are for cleaning soot damaged unpainted plaster sculptures.

Clipboard

ERIC Educational Resources Information Center

Timmons, Virginia

1978-01-01

For the teacher with a limited art materials budget plaster provides a "best buy" in terms of the variety of art projects possible and relative cost. With plaster, the student can cast blocks for printmaking, carving, and assemblage and use it, in combination with other materials, in crafts projects. Describes different kinds of plaster…

Fragmentation, Cost and Environmental Effects of Plaster Stemming Method for Blasting at A Basalt Quarry

NASA Astrophysics Data System (ADS)

Cevizci, Halim

2014-10-01

In this study, the plaster stemming application for blasting at a basalt quarry is studied. Drill cuttings are generally used in open pits and quarries as the most common stemming material since these are most readily available at blast sites. However, dry drill cuttings eject very easily from blastholes without offering much resistance to blast energy. The plaster stemming method has been found to be better than the drill cuttings stemming method due to increased confinement inside the hole and better utilization of blast explosive energy in the rock. The main advantage of the new stemming method is the reduction in the cost of blasting. At a basalt quarry, blasting costs per unit volume of rock were reduced to 15% by increasing burden and spacing distances. In addition, better fragmentation was obtained by using the plaster stemming method. Blast trials showed that plaster stemming produced finer material. In the same blast tests, +30 cm size fragments were reduced to 47.3% of the total, compared to 32.6% in the conventional method of drill cuttings stemming. With this method of stemming, vibration and air shock values increased slightly due to more blast energy being available for rock breakage but generally these increased values were small and stayed under the permitted limit for blast damage criteria unless measuring distance is too close.

Accuracy of Bolton analysis measured in laser scanned digital models compared with plaster models (gold standard) and cone-beam computer tomography images.

PubMed

Kim, Jooseong; Lagravére, Manuel O

2016-01-01

The aim of this study was to compare the accuracy of Bolton analysis obtained from digital models scanned with the Ortho Insight three-dimensional (3D) laser scanner system to those obtained from cone-beam computed tomography (CBCT) images and traditional plaster models. CBCT scans and plaster models were obtained from 50 patients. Plaster models were scanned using the Ortho Insight 3D laser scanner; Bolton ratios were calculated with its software. CBCT scans were imported and analyzed using AVIZO software. Plaster models were measured with a digital caliper. Data were analyzed with descriptive statistics and the intraclass correlation coefficient (ICC). Anterior and overall Bolton ratios obtained by the three different modalities exhibited excellent agreement (> 0.970). The mean differences between the scanned digital models and physical models and between the CBCT images and scanned digital models for overall Bolton ratios were 0.41 ± 0.305% and 0.45 ± 0.456%, respectively; for anterior Bolton ratios, 0.59 ± 0.520% and 1.01 ± 0.780%, respectively. ICC results showed that intraexaminer error reliability was generally excellent (> 0.858 for all three diagnostic modalities), with < 1.45% discrepancy in the Bolton analysis. Laser scanned digital models are highly accurate compared to physical models and CBCT scans for assessing the spatial relationships of dental arches for orthodontic diagnosis.

Plaster People...A La George Segal.

ERIC Educational Resources Information Center

Boulay, Michele

2003-01-01

Describes an art project used with eleventh- and twelfth-grade students in which they created plaster self-portraits inspired by the work of George Segal. Includes directions for the casting and lists the art materials needed for the lesson. Explains that the project requires half a semester to complete. (CMK)

Accuracy of Bolton analysis measured in laser scanned digital models compared with plaster models (gold standard) and cone-beam computer tomography images

PubMed Central

Kim, Jooseong

2016-01-01

Objective The aim of this study was to compare the accuracy of Bolton analysis obtained from digital models scanned with the Ortho Insight three-dimensional (3D) laser scanner system to those obtained from cone-beam computed tomography (CBCT) images and traditional plaster models. Methods CBCT scans and plaster models were obtained from 50 patients. Plaster models were scanned using the Ortho Insight 3D laser scanner; Bolton ratios were calculated with its software. CBCT scans were imported and analyzed using AVIZO software. Plaster models were measured with a digital caliper. Data were analyzed with descriptive statistics and the intraclass correlation coefficient (ICC). Results Anterior and overall Bolton ratios obtained by the three different modalities exhibited excellent agreement (> 0.970). The mean differences between the scanned digital models and physical models and between the CBCT images and scanned digital models for overall Bolton ratios were 0.41 ± 0.305% and 0.45 ± 0.456%, respectively; for anterior Bolton ratios, 0.59 ± 0.520% and 1.01 ± 0.780%, respectively. ICC results showed that intraexaminer error reliability was generally excellent (> 0.858 for all three diagnostic modalities), with < 1.45% discrepancy in the Bolton analysis. Conclusions Laser scanned digital models are highly accurate compared to physical models and CBCT scans for assessing the spatial relationships of dental arches for orthodontic diagnosis. PMID:26877978

[Contribution of computer-aided design for the conception of custom-made implants in Pectus Excavatum surgical treatment. Experience of the Nantes plastic surgery unit].

PubMed

Tilliet Le Dentu, H; Lancien, U; Sellal, O; Duteille, F; Perrot, P

2018-02-01

Pectus excavatum is the most common congenital chest malformation and is a common reason for consultation in plastic surgery. Our attitude is most often a filling of the depression with a custom-made silicone prosthesis. The objective of this work was to evaluate the interest of computer-aided design (CAD) of implants compared to the conventional plaster molds method. We have collected all the cases of custom-made silicone implants to treat funnel chests in our plastic surgery department. The quality of the results was evaluated by the patient, and in a blind manner by the surgical team using photographs and standardized surveys. The pre-operative delays, the operating time and length of hospital stays, the number of surgical recoveries, and the post-operative surgical outcomes were recorded. Between 1990 and 2016, we designed 29 silicone thoracic implants in our department. Before 2012, implants were made from plaster chest molds (n=13). After this date, implants were designed by CAD (n=16). Patients rated their results as "good" or "excellent" in 77% and 86% of cases respectively in the plaster and CAD groups. The surgical team's ratings for CAD implant reconstructions were better than in the plaster group: 8.17 versus 6.96 (P=0.001). CAD implants were significantly less detectable than the plaster group implants. The operating time was reduced in the CAO group: 60.2 compared to 74.7minutes in the plaster group (P=0.04), as was the length of hospitalization: 3.5 versus 5.3 days (P=0.01). There were no significant differences between the two groups in terms of post-operative complications. The management of pectus excavatum by a custom-made silicone implant is a minimally invasive method that provides good cosmetic results. The design of these implants is facilitated and qualitatively improved by CAD. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Plastering. Pre-Apprenticeship Phase 2 Training. Student Training Modules.

ERIC Educational Resources Information Center

Hamblen, Ron

These 20 Student Training Modules on plastering comprise one of nine sets of self-paced learning modules developed for Pre-Apprenticeship Phase 2 Training. (A companion instructor's guide is available separately as CE 031 569.) The modules are designed to impart trade knowledge and skills to the student. Each module contains some or all of the…

Specificity and Sensitivity Ratios of the Pediatric Language Acquisition Screening Tool for Early Referral-Revised.

ERIC Educational Resources Information Center

Sherman, Tracy; Shulman, Brian B.

1999-01-01

This study examined test characteristics of the Pediatric Language Acquisition Screening Tool for Early Referral-Revised (PLASTER-R), a set of developmental questionnaires for children 3 to 60 months of age. The PLASTER-R was moderately to highly successful in identifying children within normal limits for language development. Test-retest…

Plaster Casts after Antique Sculpture: Their Role in the Elevation of Public Taste and in American Art Instruction.

ERIC Educational Resources Information Center

McNutt, James K.

1990-01-01

Examines the social, ideological, and cultural forces in colonial United States when plaster casts of Grecian and Roman sculpture were introduced. Describes how they were used in U.S. public schools and art museums to transmit the cultural heritage at the end of the nineteenth century. (KM)

[Toxic mustard plaster dematitis and phototoxic dematitis after application of bergamot oil].

PubMed

Weisenseel, P; Woitalla, S

2005-12-15

Two cases that illustrate the risks attendant on the therapeutic use of natural medications by laypersons are reported. In the first case, the application of a mustard plaster triggered toxic dermatitis. In the second case, a session in a solarium after the external application of bergamot oil resulted in a phototoxic reaction.

MTR, TRA603. CONTROL ROOM DETAILS. ACOUSTIC PLASTER CEILING, USHAPED CONSOLE, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

MTR, TRA-603. CONTROL ROOM DETAILS. ACOUSTIC PLASTER CEILING, U-SHAPED CONSOLE, INSTRUMENT PANELS, GLASS DOOR, ASPHALT TILE FLOOR AND COLORS. BLAW-KNOX 3150-803-11, 10/1950. INL INDEX NO. 531-0603-00-098-100570, REV. 3. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

21 CFR 358.150 - Labeling of wart remover drug products.

Code of Federal Regulations, 2010 CFR

2010-04-01

... any product formulated in a collodion-like vehicle. (i) “If product gets into the eye, flush with... minutes.”) “Dry area thoroughly.” (If appropriate: “Cut plaster to fit wart.”) “Apply medicated plaster... water for 5 minutes.”) “Dry area thoroughly. Apply” (select one of the following, as appropriate: “one...

21 CFR 358.150 - Labeling of wart remover drug products.

Code of Federal Regulations, 2014 CFR

2014-04-01

... any product formulated in a collodion-like vehicle. (i) “If product gets into the eye, flush with... minutes.”) “Dry area thoroughly.” (If appropriate: “Cut plaster to fit wart.”) “Apply medicated plaster... water for 5 minutes.”) “Dry area thoroughly. Apply” (select one of the following, as appropriate: “one...

21 CFR 358.150 - Labeling of wart remover drug products.

Code of Federal Regulations, 2013 CFR

2013-04-01

... any product formulated in a collodion-like vehicle. (i) “If product gets into the eye, flush with... minutes.”) “Dry area thoroughly.” (If appropriate: “Cut plaster to fit wart.”) “Apply medicated plaster... water for 5 minutes.”) “Dry area thoroughly. Apply” (select one of the following, as appropriate: “one...

21 CFR 358.150 - Labeling of wart remover drug products.

Code of Federal Regulations, 2012 CFR

2012-04-01

... any product formulated in a collodion-like vehicle. (i) “If product gets into the eye, flush with... minutes.”) “Dry area thoroughly.” (If appropriate: “Cut plaster to fit wart.”) “Apply medicated plaster... water for 5 minutes.”) “Dry area thoroughly. Apply” (select one of the following, as appropriate: “one...

Fort Gordon Woodworth Library: Historic Building Survey

DTIC Science & Technology

2008-10-01

9 4. Wall and Ceiling Finish ...reference room are covered with replacement carpet. 4. Wall and Ceiling Finish : The inside of the exterior walls are covered with plaster. The...individual rooms are divided by 0’-4” partition walls clad WOODWORTH LIBRARY (page 10) with a mixture of drywall and wood paneling. A 3’-0” plaster

View of Arcade interior at entrance to Snack House Restaurant. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of Arcade interior at entrance to Snack House Restaurant. Note scored plaster detail replicating stone construction joints on brick rearing walls, and detailed plaster relief panels. Various color schemed from panels and cornice details are visible throughout the building and in historic photographs - Post Office Arcade, 2118 First Street, Fort Myers, Lee County, FL

Moisture buffer capacity of cement-lime plasters with enhanced thermal storage capacity

NASA Astrophysics Data System (ADS)

Fořt, Jan; Pavlíková, Milena; Pavlík, Zbyšek

2017-07-01

Indoor air temperature and relative humidity represent important parameters for health and working efficiency of buildings occupants. Beside the moderation of temperature, investigation of hygric properties of building materials with connection to indoor relative humidity variation became recognized as a relevant factor for energy efficient building maintenance. The moisture buffer value introduced in the Nordtest protocol can be used for estimation of moisture buffer capacity of building materials or their multi-layered systems. In this paper, both the ideal and real moisture buffer values are examined on the basis of simulation of diurnal relative humidity fluctuations in plasters with incorporated PCM admixture. Retrieved data points to a complex effect of the tested plasters on possible moderation of buildings interior climate.

Accuracy and eligibility of CBCT to digitize dental plaster casts.

PubMed

Becker, Kathrin; Schmücker, Ulf; Schwarz, Frank; Drescher, Dieter

2018-05-01

Software-based dental planning requires digital casts and oftentimes cone-beam computed tomography (CBCT) radiography. However, buying a dedicated model digitizing device can be expensive and might not be required. The present study aimed to assess whether digital models derived from CBCT and models digitized using a dedicated optical device are of comparable accuracy. A total of 20 plaster casts were digitized with eight CBCT and five optical model digitizers. Corresponding models were superimposed using six control points and subsequent iterative closest point matching. Median distances were calculated among all registered models. Data were pooled per scanner and model. Boxplots were generated, and the paired t test, a Friedman test, and a post-hoc Nemenyi test were employed for statistical comparison. Results were found significant at p < 0.05. All CBCT devices allowed the digitization of plaster casts, but failed to reach the accuracy of the dedicated model digitizers (p < 0.001). Median distances between CBCT and optically digitized casts were 0.064 + - 0.005 mm. Qualitative differences among the CBCT systems were detected (χ 2  = 78.07, p < 0.001), and one CBCT providing a special plaster cast digitization mode was found superior to the competitors (p < 0.05). CBCT systems failed to reach the accuracy from optical digitizers, but within the limits of the study, accuracy appeared to be sufficient for digital planning and forensic purposes. Most CBCT systems enabled digitization of plaster casts, and accuracy was found sufficient for digital planning and storage purposes.

Terahertz analysis of stratified wall plaster at buildings of cultural importance across Europe

NASA Astrophysics Data System (ADS)

Walker, Gillian C.; Jackson, J. Bianca; Giovannacci, David; Bowen, John W.; Delandes, Bruno; Labaune, Julien; Mourou, Gerard; Menu, Michel; Detalle, Vincent

2013-05-01

Terahertz (THz) radiation is being developed as a tool for the analysis of cultural heritage, and due to recent advances in technology is now available commercially in systems which can be deployed for field analysis. The radiation is capable of penetrating up to one centimetre of wall plaster and is delivered in ultrafast pulses which are reflected from layers within this region. The technique is non-contact, non-invasive and non-destructive. While sub-surface radar is able to penetrate over a metre of wall plaster, producing details of internal structures, infrared and ultraviolet techniques produce information about the surface layers of wall plaster. THz radiation is able to provide information about the interim region of up to approximately one centimetre into the wall surface. Data from Chartres Cathedral, France, Riga Dome Cathedral, Latvia, and Chartreuse du Val de Bénédiction, France is presented each with different research questions. The presence of sub-surface paint layers was expected from documentary evidence, dating to the 13th Century, at Chartres Cathedral. In contrast, at the Riga Dome Cathedral surface painting had been obscured as recently as 1941 during the Russian occupation of Latvia using white lead-based paint. In the 13th Century, wall paintings at the Chapel of the Frescos, Chartreuse du Val de Benediction in Villeneuve les Avignon were constructed using sinopia under-painting on plaster covering uneven stonework.. This paper compares and contrasts the ability of THz radiation to provide information about sub-surface features in churches and Cathedrals across Europe by analysing depth based profiles gained from the reflected signal.

Effects of forced deep breathing on blood flow velocity in the femoral vein: Developing a new physical prophylaxis for deep vein thrombosis in patients with plaster cast immobilization of the lower limb.

PubMed

Nakanishi, Keisuke; Takahira, Naonobu; Sakamoto, Miki; Yamaoka-Tojo, Minako; Katagiri, Masato; Kitagawa, Jun

2018-02-01

Patients with plaster cast immobilization of the lower limb have an estimated symptomatic venous thromboembolism rate of 5.5%. However, there is currently no practical physical prophylaxis for deep-vein thrombosis (DVT). The objective of this study was to examine the effects of forced deep breathing on peak blood velocity in the superficial femoral vein (PBVFV), which is a surrogate measure of the efficacy of thromboprophylaxis against DVT, in patients with plaster cast immobilization of the lower limb. Nine young males and 18 elderly males were recruited. We immobilized the right lower limb of each subject with a plaster splint and measured PBVFV during forced deep breathing in supine and sitting positions. In all subjects, PBVFV during forced deep breathing in both positions was significantly higher than at rest. There was no significant difference in the PBVFV change ratio for three breathing rates in the sitting position for the young subjects (15breaths/min: 415%, 5breaths/min: 475%, 3breaths/min: 483%), whereas that for the elderly subjects at 3breaths/min (449%) was significantly higher than that at 15breaths/min (284%). Forced deep breathing significantly increased PBVFV in patients with plaster cast immobilization of the lower limb in both supine and sitting positions. Testing the efficacy and adherence in clinical contexts, and following up with the incidence rate of DVT in future studies, is necessary for the development of a new physical prophylaxis for DVT. Copyright © 2017 Elsevier Ltd. All rights reserved.

Far infrared emitting plaster in knee osteoarthritis: a single blinded, randomised clinical trial.

PubMed

Bagnato, G L; Miceli, G; Atteritano, M; Marino, N; Bagnato, G F

2012-12-20

Therapeutic approach of osteoarthritis (OA) still represents a challenge in clinical practice. The aim of the study is to assess the efficacy of far infrared (FIR) emitting plaster in the treatment of knee OA. This is a randomized, single-blind, placebo-controlled, parallel group with equal randomization (1:1), clinical trial. Patients affected by knee OA were randomly allocated to 1 of 2 treatment groups, either placebo plaster or far infrared emitting plaster. Primary endpoint was to assess pain improvement from baseline to 1 months posttreatment in the visual analogue score (VAS). Secondary end point was to evaluate pain score after 1 week of treatment and to compare ultrasonographic findings after 1 month of treatment. Each group comprised 30 (in the FIR group) and 30 (in the placebo group) completers. VAS scores of the placebo and the FIR group were significantly lower at 1 week post-treatment (95% confidence interval CI = -1.14 to 0.31; P<0.05) and at the end of the study (95% confidence interval CI = -2.57 to -0.89; P=0.01). Effect size was -0.43 after one week of treatment and -1.38 after one month of treatment. The mean decrease in VAS values was ≥ 20% in the FIR group. The number of patients from the FIR group with joint effusion was lower (40%) compared to baseline (80%), while no changes were seen among the placebo group. Far infrared emitting plaster could be considered an effective non-pharmacological choice for the therapeutic management of knee OA.

21 CFR 358.150 - Labeling of wart remover drug products.

Code of Federal Regulations, 2011 CFR

2011-04-01

....” (iv) “Do not use on moles, birthmarks, warts with hair growing from them, genital warts, or warts on... minutes.”) “Dry area thoroughly.” (If appropriate: “Cut plaster to fit wart.”) “Apply medicated plaster... water for 5 minutes.”) “Dry area thoroughly. Apply” (select one of the following, as appropriate: “one...

The Contributions Regarding the Use of Microwave to Obtain Modeling Gypsum for Phonic-Absorbent Construction and Orthopedic Materials

NASA Astrophysics Data System (ADS)

Pop, P. A.; Ungur, P. A.; Caraban, A.; Marcu, F.

2009-11-01

The paper has presented some experiments realized at "Congips" Co. Oradea and University of Oradea, regarding of increase machining efficiency and quality for modeling gypsum plaster by using of microwave energy to gypsum ore roast. The elaboration process of microwave energy for modeling gypsum plaster has done on electromagnetic waves properties and specific properties for dielectric materials. Microwaves are radiations of electromagnetic waveform nature, determine by pulsations of electrical-E) and magnetically-H components of electromagnetic wave in interdependence with Maxwell equations. The gypsum ore is calcium sulphate dehydrate (CaSO4ṡ2H2O) using at modeling gypsum plaster fabrication, which is calcium sulphate hemihydrate (CaSO4ṡ1/2H2O), that has behavior of dielectric with losses. The gypsum ore getting in microwave field, in conditions of predictable pressure and temperature has transformed in modeling gypsum plaster, by quick lost of a part from crystallization water. The processing time is very short, which due to a great productivity and machining efficiency, finally of low process cost. All of these recommend continuing the research at pilot station level.

Properties of a hybrid plaster-fibreglass cast

PubMed Central

Charles, Mark N.; Yen, David

2000-01-01

Objective To examine the suitability of a plaster-fibreglass hybrid cast for orthopedic applications, comparing them to plaster of Paris (POP) and fibreglass constructs. Method Groups of 10 standardized hybrid, POP and fibreglass casts were studied. An Instron servo-hydraulic system was used to test the casts in 3-point bending and shear. Outcome measures Strength, stiffness, weight, thickness and cost of the 3 types of cast, and shear strength at the interface between the POP and fibreglass in the hybrid casts. Results The hybrid casts were twice as strong as the POP constructs, were stiffer and weighed 14% less but were thicker and cost 2.5 times more. They were almost as strong as and less than half the cost of the fibreglass constructs but were thicker, not as stiff, and weighed 42% more. The shear strength of the POP–fibreglass interface in the hybrid casts was higher than the 3-point bending strength of this construct by a factor of 3. Conclusions Plaster-fibreglass hybrid casts should be considered for orthopedic use on the basis of their strength, stiffness, weight and cost, combined with their acknowledged advantages of good moulding ability and water resistance. PMID:11045095

Delamination of plasters applied to historical masonry walls: analysis by acoustic emission technique and numerical model

NASA Astrophysics Data System (ADS)

Grazzini, A.; Lacidogna, G.; Valente, S.; Accornero, F.

2018-06-01

Masonry walls of historical buildings are subject to rising damp effects due to capillary or rain infiltrations, which in the time produce decay and delamination of historical plasters. In the restoration of masonry buildings, the plaster detachment frequently occurs because of mechanical incompatibility in repair mortar. An innovative laboratory procedure is described for test mechanical adhesion of new repair mortars. Compression static tests were carried out on composite specimens stone block-repair mortar, which specific geometry can test the de-bonding process of mortar in adherence with a stone masonry structure. The acoustic emission (AE) technique was employed for estimating the amount of energy released from fracture propagation in adherence surface between mortar and stone. A numerical simulation was elaborated based on the cohesive crack model. The evolution of detachment process of mortar in a coupled stone brick-mortar system was analysed by triangulation of AE signals, which can improve the numerical model and predict the type of failure in the adhesion surface of repair plaster. Through the cohesive crack model, it was possible to interpret theoretically the de-bonding phenomena occurring at the interface between stone block and mortar. Therefore, the mechanical behaviour of the interface is characterized.

A comparison of the mechanical properties of fiberglass cast materials and their clinical relevance.

PubMed

Berman, A T; Parks, B G

1990-01-01

The mechanical properties of five synthetic fiberglass casting materials were evaluated and compared with the properties of plaster of Paris. Two of the tests were designed to bear clinical relevance and the third to determine intrinsic material properties. The effect of water on strength degradation was also evaluated. It was found that the synthetics as a group are far superior to plaster of Paris in all methods of testing and that, among the synthetics, KCast Tack Free, Deltalite "S", and KCast Improved were the stronger materials. Clinically, the most important results are that the synthetics attain their relatively high strength in a much shorter time frame than does plaster of Paris, and retain 70-90% of their strength after being immersed in water and allowed to dry.

High Strength Phosphogypsum and Its Use as a Building Material

NASA Astrophysics Data System (ADS)

Kanno, Wellington Massayuki; Rossetto, Hebert Luis; de Souza, Milton Ferreira; Máduar, Marcelo Francis; de Campos, Marcia Pires; Mazzilli, Barbara Paci

2008-08-01

A new process (patent applied) that works equally well with both plaster of mineral gypsum and phosphogypsum for the preparation of gypsum components, UCOS, has been developed. The process consists of the following steps: humidification of plaster by fine water droplets, uni-axial compression, hydration reaction and drying. Strong hydrogen bonds develop among the crystals together with adhesion provided by confined water that accounts for nearly 70% of the adhesion forces. By reducing the plaster to water ratio to close the minimum necessary, new features are generated. An experimental house has been constructed, in which walls and ceilings have been built of gypsum and phosphogypsum. Since phosphogypsum potentially contain radioactive elements, the application of an activity concentration index to the phosphogypsum employed in the building was carried out.

Investigation of the seismic resistance of interior building partitions, phase 1

NASA Astrophysics Data System (ADS)

Anderson, R. W.; Yee, Y. C.; Savulian, G.; Barclay, B.; Lee, G.

1981-02-01

The effective participation of wood-framed interior shear wall partitions when determining the ultimate resistance capacity of two- and three-story masonry apartment buildings to seismic loading was investigated. Load vs. deflection tests were performed on 8 ft by 8 ft wall panel specimens constructed of four different facing materials, including wood lath and plaster, gypsum lath and plaster, and gypsum wallboard with joints placed either horizontally or vertically. The wood lath and plaster construction is found to be significantly stronger and stiffer than the other three specimens. Analyses of the test panels using finite element methods to predict their static resistance characteristics indicates that the facing material acts as the primary shear-resisting structural element. Resistance of shear wall partitions to lateral loads was assessed.

Acoustic Identification of Filler Materials in Unexploded Ordnance

DTIC Science & Technology

2006-04-01

PBXN- 103 CH-6 PBXW- 108 Parrafin ( wax ) Baratol (76/24) Plaster TNT Octol (50/50) Comp B PETN Concrete Lo ng itu di na l V el oc ity (m /s ec...26 3.7.3 Identification of Wax fillers...plaster and wax from “other” items including explosives. A series of field tests are described that focus on acoustic measurements on both inert and live

Internal fabrics in magmatic plutons emplaced in extended brittle crust - insight from analogue models with AMS (Anisotropy of Magnetic Susceptibility)

NASA Astrophysics Data System (ADS)

Mirzaei, Masoud; Zavada, Prokop; Machek, Matej; Roxerova, Zuzana

2016-04-01

Magma emplacement in extended brittle crust was simulated by injecting plaster of Paris (magma) into a large sandbox with central deformable rubber sheet. Analog magma is during the experiments injected through small circular inlet cut in the center of the elastic sheet. Injection force oscillation during the steadily evacuating analog magma was recorded during the experiments and regularly showed 3-4 increases followed by a quick drop. The recorded oscillation amplitude is largest for static injection without extension of the sandbox, which formed a columnar body with concentric and zonal internal fabric. Experiments including normal or oblique 20% extension resulted in along rift axis elongated oblate ellipsoidal pluton with rift parallel ridges in the top part of the pluton. Inspection of horizontal profiles show bone-shaped internal zoning patterns limited by conjugate sets of shear zones. Orientation of these internal shear zones is correlated with the sand-clock fault pattern developed in the overburden sand pack. Another set of shear zones parallel with the long axes of the plutons (rift axis) are associated with successive emplacement of distinct plaster pulses during the buildup of the entire body. The innermost lastly emplaced pulses of plaster display weak vertical magnetic fabrics with vertical lineations, while the outer shells of already emplaced plaster reveal stronger and margin parallel oblate magnetic fabrics with subhorizontal lineations. We interpret the vertical innermost fabrics as a result of active ascent of plaster from the injection inlet, while the fabrics in the outer zones likely reflect push due to inflation of the inner domain reflected in the reworking of the magnetic fabric.

Measurements using orthodontic analysis software on digital models obtained by 3D scans of plaster casts : Intrarater reliability and validity.

PubMed

Czarnota, Judith; Hey, Jeremias; Fuhrmann, Robert

2016-01-01

The purpose of this work was to determine the reliability and validity of measurements performed on digital models with a desktop scanner and analysis software in comparison with measurements performed manually on conventional plaster casts. A total of 20 pairs of plaster casts reflecting the intraoral conditions of 20 fully dentate individuals were digitized using a three-dimensional scanner (D700; 3Shape). A series of defined parameters were measured both on the resultant digital models with analysis software (Ortho Analyzer; 3Shape) and on the original plaster casts with a digital caliper (Digimatic CD-15DCX; Mitutoyo). Both measurement series were repeated twice and analyzed for intrarater reliability based on intraclass correlation coefficients (ICCs). The results from the digital models were evaluated for their validity against the casts by calculating mean-value differences and associated 95 % limits of agreement (Bland-Altman method). Statistically significant differences were identified via a paired t test. Significant differences were obtained for 16 of 24 tooth-width measurements, for 2 of 5 sites of contact-point displacement in the mandibular anterior segment, for overbite, for maxillary intermolar distance, for Little's irregularity index, and for the summation indices of maxillary and mandibular incisor width. Overall, however, both the mean differences between the results obtained on the digital models versus on the plaster casts and the dispersion ranges associated with these differences suggest that the deviations incurred by the digital measuring technique are not clinically significant. Digital models are adequately reproducible and valid to be employed for routine measurements in orthodontic practice.

The management of amputations of the leg using a new rigid foam plaster for prosthetic fitting.

PubMed

Hölter, W; Echterhoff, M; Blömer, A; Verfürden, H

1980-01-01

This paper describes the use of a rigid polyurethane foam to construct a stump socket for immediate or early prosthetic fitting in 15 patients with amputation through the leg. The foam plaster is poured into a prepared cotton sleeve, with a zip incorporated, and rolled out to a layer 4 mm thick. The filled sleeve is put around the stump and the zip closed, moulding the sleeve firmly to the stump. The closed sleeve hardens into a rigid polyurethane shell within 20 min. Aferwards the skeletal prosthetic components are fixed with the same rigid foam. The polyurethane foam socket is quickly and cleanly prepared, only one third of the weight of a plaster of Paris cast and is easily removed by means of the zip, allowing access to the stump.

Prosthesis Material

NASA Technical Reports Server (NTRS)

1995-01-01

In this photograph, Sandra Rossi user her NASA-developed prosthesis for the first time. Derived from foam insulation technology used to protect the Space Shuttle External Tank from excessive heat, FAB/CAD, a subsidiary of the Harshberger Prosthetic and Orthotic Center, utilized the technology to replace the heavy, fragile plaster they used to produce master molds for prosthetics. The new material was lighter, cheaper and easier to manufacture than plaster, resulting in lower costs to the customer.

General engineering specifications for 6000 tpd SRC-I Demonstration Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This volume contains specifications for architectural features of buildings for the SRC-1 Demonstration Plant: skylights, ventilators, sealants, doors, mirrors, furring and lathing, gypsum plaster, lightweight plaster, wallboard, ceramic tile, acoustic ceiling systems, resilient flooring, carpeting, brick flooring, architectural painting, vinyl wall covering, chalkboards, tackboards, toilets, access flooring, lockers, partitions, washroom accessories, unit kitchens, dock levels, seals, shelters, custom casework, auditorium seats, drapery tacks, prefabricated buildings, stairs, elevators, shelves, etc. (LTN).

Benefit from NASA

NASA Image and Video Library

1995-01-01

In this photograph, Sandra Rossi user her NASA-developed prosthesis for the first time. Derived from foam insulation technology used to protect the Space Shuttle External Tank from excessive heat, FAB/CAD, a subsidiary of the Harshberger Prosthetic and Orthotic Center, utilized the technology to replace the heavy, fragile plaster they used to produce master molds for prosthetics. The new material was lighter, cheaper and easier to manufacture than plaster, resulting in lower costs to the customer.

Benefit from NASA

NASA Image and Video Library

1995-01-01

In this photograph, James Carden uses a NASA-developed prosthesis to moved planks around his home. Derived from foam insulation technology used to protect the Space Shuttle External Tank from excessive heat, FAB/CAD, a subsidiary of the Harshberger Prosthetic and Orthotic Center, utilized the technology to replace the heavy, fragile plaster they used to produce master molds for prosthetics. The new material was lighter, cheaper and easier to manufacture than plaster, resulting in lower costs to the customer.

Benefit from NASA

NASA Image and Video Library

2004-04-15

In this photograph, Amputee Amie Bradly uses a NASA-developed prosthesis to paint her fingernails. Derived from foam insulation technology used to protect the Space Shuttle External Tank from excessive heat, FAB/CAD, a subsidiary of the Harshberger Prosthetic and Orthotic Center, utilized the technology to replace the heavy, fragile plaster they used to produce master molds for prosthetics. The new material was lighter, cheaper and easier to manufacture than plaster, resulting in lower costs to the customer.

Prosthesis Material

NASA Technical Reports Server (NTRS)

2004-01-01

In this photograph, Amputee Amie Bradly uses a NASA-developed prosthesis to paint her fingernails. Derived from foam insulation technology used to protect the Space Shuttle External Tank from excessive heat, FAB/CAD, a subsidiary of the Harshberger Prosthetic and Orthotic Center, utilized the technology to replace the heavy, fragile plaster they used to produce master molds for prosthetics. The new material was lighter, cheaper and easier to manufacture than plaster, resulting in lower costs to the customer.

Prosthesis Material

NASA Technical Reports Server (NTRS)

1995-01-01

In this photograph, James Carden uses a NASA-developed prosthesis to moved planks around his home. Derived from foam insulation technology used to protect the Space Shuttle External Tank from excessive heat, FAB/CAD, a subsidiary of the Harshberger Prosthetic and Orthotic Center, utilized the technology to replace the heavy, fragile plaster they used to produce master molds for prosthetics. The new material was lighter, cheaper and easier to manufacture than plaster, resulting in lower costs to the customer.

AMS of an Analogue Non-Scale Model Simulating Diapiric Pluton Emplacement

NASA Astrophysics Data System (ADS)

Hrouda, F.; Kratinova, Z.; Zavada, P.; Schulmann, K.

2004-12-01

Development of magnetic fabric within a pluton during its diapiric ascent was investigated using an analogue non-scale model of plaster of Paris containing small amount of fine-grained (less than 0.09 mm) homogeneously mixed magnetite, with resulting bulk susceptibility being in the order of 10-3 [SI]. The apparatus for this modelling consists of a manual squeezer with calibrated spring and a perspex container. Stratified coloured to visualize internal flow geometries, weak plaster layer at the bottom of the container was forced to intrude overlying fine-grained (>0.017mm) sand through a hole in a board attached to the squeezer. A retarding compound was admixed into the plaster to postpone the solidification of plaster. After solidifying the model, small oriented cylindrical specimens (7 mm in diameter and 6 mm in height) were drilled and their anisotropy of magnetic susceptibility (AMS) was measured with the KLY-4S Kappabridge. The magnetic fabric in the margins of the vertical column of the diapir is characterized by high degree of AMS (P'=1.26-1.30), neutral to oblate AMS ellipsoid (T=0.2-0.6) and vertical magnetic lineations and foliations. In the vent area, the degree of AMS is also high, but the AMS ellipsoid being strongly prolate (T= -1 to -0.8) with vertical magnetic lineations. In the interior of the plug above the vent zone, abrupt transition into horizontal lineations and foliations take place and the low degree of AMS (P'=1.05-1.10) marks the area where strongly prolate magnetic fabric is being gradually changed into the magnetic fabric characterized by neutral to oblate AMS ellipsoid. This type of magnetic fabric extends to the apical part of the body. In the extrusive portions of the diapir, oblate magnetic fabric increases in anisotropy (T=0.8-1, P'=1.26-1.29), while the front of the radial extrusion shows horizontal lineations parallel to the margin and neutral AMS ellipsoids (T=0.2-0.6,P'=1.23-1.26). This changeover of fabric thus indicates divergent flow in the radial extrusion. The development of AMS fabric is correlated with complex flow pattern indicated by coloured and originally horizontal plaster layers. Narrow shear zones in the margins of the plug indicate non-linear behavior of plaster during experiments.

Investigation of Layer Structure of the Takamatsuzuka Mural Paintings by Terahertz Imaging Technique

NASA Astrophysics Data System (ADS)

Inuzuka, M.; Kouzuma, Y.; Sugioka, N.; Fukunaga, K.; Tateishi, T.

2017-04-01

Terahertz imaging can be a powerful tool in conservation science for cultural heritages. In this study, a new terahertz imaging system was applied to the Takamatsuzuka mural painting of a blue dragon, and the condition of the plaster layer was diagnosed. As a result, the locations where the plaster layer appears solid on the surface but in actuality may have peeled off the underlying tuff stone were revealed and viewed as two-dimensional images.

A chemical rationalization of the processing and application of the mortar coatings: Structural, thermodynamic, and fluorescence properties

NASA Astrophysics Data System (ADS)

Lima, Nathan B.; Rogerio, V. A.; Belarmino, Marcia K. D. L.; Silva, Anderson I. S.; Ioras, Renan U. F.; Oliveira, Romilde A.; Lima, Nathalia B. D.

2018-07-01

A chemical rationalization of the processing and application of the roughcast and plaster mortar coatings was advanced. The results revealed that the structural and thermodynamic nature of the hydrogen-bonded complexes between the inorganic precursors and water molecules are associated with the physical properties of both coatings. In this sense, the workability and curing time of the roughcast and the plaster mortars studied, seemingly, are related to the nature of the water solvation in the main components of these materials: calcium hydroxide and silicon dioxide. In addition, PM7 and PM7/COSMO results indicate that the enthalpy of solvation of water by hydrogen bonds in calcium hydroxide is stronger when compared with silicon dioxide systems. Therefore, the presence of free hydrated lime (calcium hydroxide) in the precursor mixture of plaster mortar leads to the large workability and elapsed curing time of this material. On the other hand, the absence of free hydrated lime in the precursor mixture of the roughcast mortar leads to its poor workability and faster elapsed curing time. Further, fluorescence microscopy experiments revealed that the inorganic compounds present in the cement precursor were transformed into different materials, that exhibit red and blue fluorescence. Finally, mechanical tests showed a tensile strength average 0.67 MPa for the plaster mortar material, whereas for the roughcast material is 0.53 MPa.

[A preliminary study on the forming quality of titanium alloy removable partial denture frameworks fabricated by selective laser melting].

PubMed

Liu, Y F; Yu, H; Wang, W N; Gao, B

2017-06-09

Objective: To evaluate the processing accuracy, internal quality and suitability of the titanium alloy frameworks of removable partial denture (RPD) fabricated by selective laser melting (SLM) technique, and to provide reference for clinical application. Methods: The plaster model of one clinical patient was used as the working model, and was scanned and reconstructed into a digital working model. A RPD framework was designed on it. Then, eight corresponding RPD frameworks were fabricated using SLM technique. Three-dimensional (3D) optical scanner was used to scan and obtain the 3D data of the frameworks and the data was compared with the original computer aided design (CAD) model to evaluate their processing precision. The traditional casting pure titanium frameworks was used as the control group, and the internal quality was analyzed by X-ray examination. Finally, the fitness of the frameworks was examined on the plaster model. Results: The overall average deviation of the titanium alloy RPD framework fabricated by SLM technology was (0.089±0.076) mm, the root mean square error was 0.103 mm. No visible pores, cracks and other internal defects was detected in the frameworks. The framework fits on the plaster model completely, and its tissue surface fitted on the plaster model well. There was no obvious movement. Conclusions: The titanium alloy RPD framework fabricated by SLM technology is of good quality.

Effect of a plaster containing DHEP and heparin in acute ankle sprains with oedema: a randomized, double-blind, placebo-controlled, clinical study.

PubMed

Coudreuse, J-M; de Vathaire, F

2010-09-01

Ankle sprains are the most frequent injuries in sport and daily life, and are usually treated with anti-inflammatory drugs or compounds that have an effect on microcirculation. The efficacy and tolerability of a novel plaster containing both diclofenac epolamine (DHEP) and heparin in the treatment of acute painful ankle sprains with oedema was investigated in a randomized, double-blind, placebo-controlled study. This study, carried out in 32 French medical centres, enrolled 233 patients (148 male and 86 female, aged 18-65 years) with an ankle sprain that had occurred within the previous 48 hours. Patients were treated once daily with DHEP heparin or placebo plaster for 7 days. Reduction in ankle joint swelling measured by submalleolar circumference was the primary efficacy endpoint; secondary endpoints were pain (at rest, in active mobilization, by passive stretch and by pressure), functional disability and global judgement of efficacy and tolerability. DHEP heparin-treated patients experienced a significantly greater reduction in joint swelling compared with placebo (p = 0.005). The reduction in pain was also in favour of DHEP heparin patients, with significantly lower pain in DHEP heparin-treated than placebo-treated patients within 3 hours of the first application (p < 0.05). Only two patients in the DHEP heparin plaster group and six in the placebo group experienced minor adverse events, all of which resolved spontaneously. By design, the study was limited to a placebo-controlled comparison, and there was no test for possible selection bias (subsequently ruled out by choice of efficacy parameters and measures) that may have resulted in a baseline imbalance between patient groups. Results confirm the efficacy of DHEP heparin plaster compared with placebo for the treatment of painful ankle sprain with oedema. Prompt control of pain and oedema may shorten the time to initiation of a rehabilitation programme, thus reducing the risk of ankle disability recurrence and the development of chronic injury.

Use of polyurethane foam inside plaster casts to prevent the onset of heel sores in the population at risk. A controlled clinical study.

PubMed

Forni, Cristiana; Loro, Loretta; Tremosini, Morena; Mini, Sandra; Pignotti, Elettra; Bigoni, Ombretta; Guzzo, Giuseppe; Bellini, Laura; Trofa, Carmela; Di Cataldo, Anna M; Guzzi, Marilena

2011-03-01

The aim of this study was to test the effectiveness of polyurethane foam in contact with the heel inside a plaster cast to decrease the rate of pressure sores in the population at most risk. The rate of pressure sores caused by the plaster cast is reported to be 14-15% in the paediatric population, 33.3% in patients having undergone chemotherapy for bone tumours and 43% in orthopaedic patients who already have sore skin when the cast is applied (grade 1 lesion) to the heel. Controlled clinical trial. From November 2007-January 2009, all consecutive subjects requiring lower limb casts having undergone chemotherapy and/or presenting heel soreness received polyurethane foam in contact with the skin of the heel before applying the cast. The results were compared with those of patients with the same risk factors but were not administered the foam and were enrolled from May 2005-August 2006. In total, 156 patients were enrolled, 85 in the control group and 71 in the experimental group. In the experimental group, 2 of the 56 patients (3.6%) with sore skin developed a pressure sore compared with 21 of 49 (42.9%) in the control group without polyurethane foam (p < 0.0005). In the experimental group, one of the 24 patients (4.2%) patients undergoing chemotherapy developed a pressure sore compared with 18 of 54 (33.3%) in the control group (p = 0.005). Placing polyurethane foam in contact with the skin of the heel inside a plaster cast prevents the formation of pressure sores. This study provides evidence that using polyurethane foam to prevent sores even inside plaster casts in populations at most risk is a simple and cost-effective strategy and decreases the discomfort, pain and risks in these patients. © 2011 Blackwell Publishing Ltd.

Intensive Survey at 11-Jd-126, Jo Daviess County, Illinois. Volume 1.

DTIC Science & Technology

1983-07-01

out. The joints between the roofing is also plastered; carefully covered about a foot thick with grass which we cut with our . knives, & four or...plaster had been pushed or smeared up against the walls or joints provide opportunities to reconstruct the diameter of the lath or withes in ,-any...of the sherds has one fairly complete edge and a small fracture on the opposing side from the opposite edge (see Figure 56), one can estimate an

Dental Assistant, Advanced. Revision

DTIC Science & Technology

1989-02-01

compound , or model- ing plaster instead of the rubber dam retainer Removing the Rubber Dam (figures 4-4 and 4-5). A ligature can also be used After the...roots or split crowns. If a is checked. When directed by the dental officer, ligature, dental compound , or modeling plaster remove the rubber dam...34clean" and 1 " dirty " JOB STEPS 1. Wash hands. 2. Recor! patient’s name. 3. Explain procedure to patient. 4. Tell patient to lie in bed or be seated

Wastewater Sludge Used as Material for Bricks Fabrication

NASA Astrophysics Data System (ADS)

Jianu, N. R.; Moga, I. C.; Pricop, F.; Chivoiu, A.

2018-06-01

Current world trends related to wastewater sludges are: reuse in agriculture, utilization as retaining material for petroleum products or utilization in construction. Bricks from sand-cement or autoclaved cellular concrete are commonly used in construction. The authors propose innovative receipts for bricks and plasters based on textile wastewaters sludge. Centrifuged sludge is mixed with cement to obtain bricks and plaster. For bricks, the mixture is represented by 45% cement and 55% sludge. The paper presents the obtained results and the new materials used for bricks fabrication.

FGD gypsum issues

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buecker, B.

2007-11-15

The article first explains how gypsum by-product is produced in flue gas desulfurization systems in coal-fired power plants. It goes on to talk about the main markets for gypsum - wallboard manufacture (Plaster of Paris), cement production and soil stabilization. In the USA in 2006 41.6 million tons of gypsum was used by manufacturers of wallboard and plaster products, 3.0 mt for cement production and 1.1 mt for agricultural purposes. A method of determining the by-product gypsum content by thermogravimetric analysis is outlined. 4 refs., 1 fig.

Salt attack in parking garage in block of flats

NASA Astrophysics Data System (ADS)

Beran, Pavel; Frankeová, Dita; Pavlík, Zbyšek

2017-07-01

In recent years many new block of flats with parking garages placed inside the buildings were constructed. This tendency brings beyond question benefits for residents and also for city planning, but it requires new design and structural approaches and advanced material and construction solutions. The analysis of plaster damage on partition wall in parking garage in one of these buildings is presented in the paper. The damage of studied plaster is caused by the salts which are transported together with snow on cars undercarriage into garage area during winter. The snow melts and water with dissolved salts is transported by the capillary suction from concrete floor into the rendered partition wall. Based on the interior temperature, adsorbed water with dissolved chlorides evaporates and from the over saturated pore solution are formed salt crystals that damages the surface plaster layers. This damage would not occur if the partition wall was correctly isolated from the floor finish layer in the parking garage.

A novel approach for planning orthognathic surgery: the integration of dental casts into three-dimensional printed mandibular models.

PubMed

Ayoub, A F; Rehab, M; O'Neil, M; Khambay, B; Ju, X; Barbenel, J; Naudi, K

2014-04-01

A method of producing a composite model consisting of a three-dimensional printed mandible bearing plaster teeth is presented. Printed models were obtained from cone beam computed tomograms (CBCT) of dry human mandibles. The plaster casts of the teeth were obtained from impressions of the teeth of the dry mandibles. The distorted teeth of the printed models were removed and replaced by the plaster casts of the teeth using a simple transfer jig. The accuracy of the composite models obtained from six mandibles was assessed from laser scans. The scans of the dry mandibles and the composite models were superimposed and the magnitude of the discrepancies at six points on the dentition and six on the mandible were obtained. It was concluded that the errors of the method were small enough to be clinically significant. The use of the composite models is illustrated in two clinical cases. Copyright © 2013 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

CFD analysis of a rotary kiln using for plaster production and discussion of the effects of flue gas recirculation application

NASA Astrophysics Data System (ADS)

Gürtürk, Mert; Oztop, Hakan F.; Pambudi, Nugroho Agung

2018-04-01

In this study, the CFD analysis of the rotary kiln is carried out for examining effects of various parameters on energy consumption and efficiency of the rotary kiln. The flue gas recirculation using in many applications is a useful method for combusting of fuel unburned in the flue gas. Also, effects of flue gas recirculation on the combusting of fuel, operating temperature and efficiency of the rotary kiln are discussed in this study. The rotary kiln, which is considered in this study, is used in plaster plant. Two different CFD models were created and these models are compared according to many parameters such as temperature distribution, mixture fraction, the mass fraction of O2, CO, CO and CH4 in the combustion chamber. It is found that the plaster plant has a great potential for an increase in energy efficiency. Results obtained for producers of rotary kiln and burner will be useful for determining better design parameters.

Accuracy of digital models generated by conventional impression/plaster-model methods and intraoral scanning.

PubMed

Tomita, Yuki; Uechi, Jun; Konno, Masahiro; Sasamoto, Saera; Iijima, Masahiro; Mizoguchi, Itaru

2018-04-17

We compared the accuracy of digital models generated by desktop-scanning of conventional impression/plaster models versus intraoral scanning. Eight ceramic spheres were attached to the buccal molar regions of dental epoxy models, and reference linear-distance measurement were determined using a contact-type coordinate measuring instrument. Alginate (AI group) and silicone (SI group) impressions were taken and converted into cast models using dental stone; the models were scanned using desktop scanner. As an alternative, intraoral scans were taken using an intraoral scanner, and digital models were generated from these scans (IOS group). Twelve linear-distance measurement combinations were calculated between different sphere-centers for all digital models. There were no significant differences among the three groups using total of six linear-distance measurements. When limited to five lineardistance measurement, the IOS group showed significantly higher accuracy compared to the AI and SI groups. Intraoral scans may be more accurate compared to scans of conventional impression/plaster models.

Study on γ-ray exposure buildup factors and fast neutron-shielding properties of some building materials

NASA Astrophysics Data System (ADS)

Singh, Vishwanath P.; Badiger, N. M.; El-Khayatt, A. M.

2014-06-01

We have computed γ-ray exposure buildup factors (EBF) of some building materials; glass, marble, flyash, cement, limestone, brick, plaster of paris (POP) and gypsum for energy 0.015-15 MeV up to 40 mfp (mfp, mean free path) penetration depth. Also, the macroscopic effective removal cross-sections (ΣR) for fast neutron were calculated. We discussed the dependency of EBF values on photon energy, penetration depth and chemical elements. The half-value layer and kinetic energy per unit mass relative to air of building materials were calculated for assessment of shielding effectiveness. Shielding thicknesses for glass, marble, flyash, cement, limestone and gypsum plaster (or Plaster of Paris, POP) were found comparable with ordinary concrete. Among the studied materials limestone and POP showed superior shielding properties for γ-ray and neutron, respectively. Radiation safety inside houses, schools and primary health centers for sheltering and annual dose can be assessed by the determination of shielding parameters of common building materials.

Optimal Post-Operative Immobilisation for Supracondylar Humeral Fractures.

PubMed

Azzolin, Lucas; Angelliaume, Audrey; Harper, Luke; Lalioui, Abdelfettah; Delgove, Anaïs; Lefèvre, Yan

2018-05-25

Supracondylar humeral fractures (SCHFs) are very common in paediatric patients. In France, percutaneous fixation with two lateral-entry pins is widely used after successful closed reduction. Post-operative immobilisation is typically with a long arm cast combined with a tubular-bandage sling that immobilises the shoulder and holds the arm in adduction and internal rotation to prevent external rotation of the shoulder, which might cause secondary displacement. The objective of this study was to compare this standard immobilisation technique to a posterior plaster splint with a simple sling. Secondary displacement is not more common with a posterior plaster splint and sling than with a long arm cast. 100 patients with extension Gartland type III SCHFs managed by closed reduction and percutaneous fixation with two lateral-entry pins between December 2011 and December 2015 were assessed retrospectively. Post-operative immobilisation was with a posterior plaster splint and a simple sling worn for 4 weeks. Radiographs were obtained on days 1, 45, and 90. Secondary displacement occurred in 8% of patients. No patient required revision surgery. The secondary displacement rate was comparable to earlier reports. Of the 8 secondary displacements, 5 were ascribable to technical errors. The remaining 3 were not caused by rotation of the arm and would probably not have been prevented by using the tubular-bandage sling. A posterior plaster splint combined with a simple sling is a simple and effective immobilisation method for SCHFs provided internal fixation is technically optimal. IV, retrospective observational study. Copyright © 2018. Published by Elsevier Masson SAS.

Objective assessment of plaster cast quality in pediatric distal forearm fractures: Is there an optimal index?

PubMed

Labronici, Pedro José; Ferreira, Leonardo Termis; Dos Santos Filho, Fernando Claudino; Pires, Robinson Esteves Santos; Gomes, Davi Coutinho Fonseca Fernandes; da Silva, Luiz Henrique Penteado; Gameiro, Vinicius Schott

2017-02-01

Several so-called casting indices are available for objective evaluation of plaster cast quality. The present study sought to investigate four of these indices (gap index, padding index, Canterbury index, and three-point index) as compared to a reference standard (cast index) for evaluation of plaster cast quality after closed reduction of pediatric displaced distal forearm fractures. Forty-three radiographs from patients with displaced distal forearm fractures requiring manipulation were reviewed. Accuracy, sensitivity, specificity, false-positive probability, false-negative probability, positive predictive value, negative predictive value, positive likelihood ratio, and negative likelihood ratio were calculated for each of the tested indices. Comparison among indices revealed diagnostic agreement in only 4.7% of cases. The strongest correlation with the cast index was found for the gap index, with a Spearman correlation coefficient of 0.94. The gap index also displayed the best agreement with the cast index, with both indices yielding the same result in 79.1% of assessments. When seeking to assess plaster cast quality, the cast index and gap index should be calculated; if both indices agree, a decision on quality can be made. If the cast and gap indices disagree, the padding index can be calculated as a tiebreaker, and the decision based on the most frequent of the three results. Calculation of the three-point index and Canterbury index appears unnecessary. Copyright © 2016 Elsevier Ltd. All rights reserved.

Accuracy and precision of polyurethane dental arch models fabricated using a three-dimensional subtractive rapid prototyping method with an intraoral scanning technique.

PubMed

Kim, Jae-Hong; Kim, Ki-Baek; Kim, Woong-Chul; Kim, Ji-Hwan; Kim, Hae-Young

2014-03-01

This study aimed to evaluate the accuracy and precision of polyurethane (PUT) dental arch models fabricated using a three-dimensional (3D) subtractive rapid prototyping (RP) method with an intraoral scanning technique by comparing linear measurements obtained from PUT models and conventional plaster models. Ten plaster models were duplicated using a selected standard master model and conventional impression, and 10 PUT models were duplicated using the 3D subtractive RP technique with an oral scanner. Six linear measurements were evaluated in terms of x, y, and z-axes using a non-contact white light scanner. Accuracy was assessed using mean differences between two measurements, and precision was examined using four quantitative methods and the Bland-Altman graphical method. Repeatability was evaluated in terms of intra-examiner variability, and reproducibility was assessed in terms of inter-examiner and inter-method variability. The mean difference between plaster models and PUT models ranged from 0.07 mm to 0.33 mm. Relative measurement errors ranged from 2.2% to 7.6% and intraclass correlation coefficients ranged from 0.93 to 0.96, when comparing plaster models and PUT models. The Bland-Altman plot showed good agreement. The accuracy and precision of PUT dental models for evaluating the performance of oral scanner and subtractive RP technology was acceptable. Because of the recent improvements in block material and computerized numeric control milling machines, the subtractive RP method may be a good choice for dental arch models.

Calcified lesion modeling for excimer laser ablation

NASA Astrophysics Data System (ADS)

Scott, Holly A.; Archuleta, Andrew; Splinter, Robert

2009-06-01

Objective: Develop a representative calcium target model to evaluate penetration of calcified plaque lesions during atherectomy procedures using 308 nm Excimer laser ablation. Materials and Methods: An in-vitro model representing human calcified plaque was analyzed using Plaster-of-Paris and cement based composite materials as well as a fibrinogen model. The materials were tested for mechanical consistency. The most likely candidate(s) resulting from initial mechanical and chemical screening was submitted for ablation testing. The penetration rate of specific multi-fiber catheter designs and a single fiber probe was obtained and compared to that in human cadaver calcified plaque. The effects of lasing parameters and catheter tip design on penetration speed in a representative calcified model were verified against the results in human cadaver specimens. Results: In Plaster of Paris, the best penetration was obtained using the single fiber tip configuration operating at 100 Fluence, 120 Hz. Calcified human lesions are twice as hard, twice as elastic as and much more complex than Plaster of Paris. Penetration of human calcified specimens was highly inconsistent and varied significantly from specimen to specimen and within individual specimens. Conclusions: Although Plaster of Paris demonstrated predictable increases in penetration with higher energy density and repetition rate, it can not be considered a totally representative laser ablation model for calcified lesions. This is in part due to the more heterogeneous nature and higher density composition of cadaver intravascular human calcified occlusions. Further testing will require a more representative model of human calcified lesions.

PCM-enhanced lime plasters for vernacular and contemporary architecture

NASA Astrophysics Data System (ADS)

Theodoridou, Magdalini; Kyriakou, Loucas; Ioannou, Ioannis

2016-04-01

In 1997, the European Union (EU) pledged to reduce the amount of greenhouse gas emissions by 20% below the levels of 1990 by the end of 2020. In recent years it has become evident that, in order to reach that goal, EU Member States must take measures to encourage sustainability in the building industry, which is a major energy consumer. Such measures should involve the use of innovative, environmentally friendly materials and methods in new constructions, as well as the renovation of existing properties by upgrading their current state of energy efficiency. Phase Change Materials (PCMs) have the ability to absorb and release thermal energy, in the form of latent heat, during the melting or solidifying processes respectively. Thus, they may be used as additives in the production of thermally efficient composite building materials. A PCM-enhanced plaster is a heat storage medium combining an appropriate PCM with a cementitious or non-cementitious matrix to produce a low-cost thermal storage material with structural and thermostatic properties. Although innovative technologies, such as PCMs, have certainly contributed to the boost in the evolution of the building materials industry in recent years, a significant proportion of these technologies and practices have not yet been fully exploited in materials based on traditional principles. This paper focuses on the design and production of novel cementless PCM-enhanced lime plasters, in line with the traditional production technology of lime composites. The new plasters are produced using either hydrated or natural hydraulic lime binder, crushed calcarenite sand (0-2 mm) and commercial microencapsulated PCM in powder form (5% w/w of solids). Results from comparative tests between reference mixtures and mixtures with the addition of PCM, carried out 28, 56 and 90 days after laboratory production, prove the potential of PCMs in enhancing the thermal performance of traditional lime-based composites. The modified composites have significantly lower (by 55%) thermal conductivity and increased (by almost 20%) specific heat capacity at 90 days after laboratory production. At the same time, even though porosity values are higher for the PCM-enhanced renders, compared to the reference mixtures, their capillary absorption coefficient is significantly reduced (up to 60%). This is of great importance in the case of renders and may well be an indication for better expected durability in the long-term. Regarding the mechanical properties of the laboratory composites, PCM addition seems to have a negative effect on the hydraulic plasters. In contrast, when PCM is added to the hydrated lime-based plaster, no change is observed for the flexural strength, while the compressive strength is notably improved (up to 36%). The apparently improved properties of the PCM-enhanced plasters render them particularly appropriate for application in southern European climatic conditions. Due to their compatibility with traditional substrate materials (e.g. natural stone), the aforementioned composites may be used not only in new contemporary structures, but also for the renovation and retrofitting of existing buildings. The lime-based nature of their matrix and their physico-mechanical properties further extend their applicability to listed and monumental buildings.

[Case-control study on effects of external fixation combined with limited internal fixation for the treatment of Pilon fractures of Rüedi-Allgower type III].

PubMed

Duan, Da-Peng; You, Wu-Lin; Ji, Le; Zhang, Yong-Tao; Dang, Xiao-Qian; Wang, Kun-Zheng

2014-01-01

To analyze the effects of three surgical operations in the treatment of Pilon fracture of Rüedi-Allgower type III, and put forward the best therapeutic method. The clinical data of 33 patients with Pilon fracture who received surgical operations (plaster immobilization group, 10 cases; distal tibia anatomical plate group, 11 cases; external fixation with limited internal fixation group, 12 cases) from October 2009 to January 2012 were analyzed. There were 5 males and 5 females, ranging in age from 24 to 61 years in the plaster immobilization group. There were 7 males and 4 females, ranging in age from 21 to 64 years in the distal tibia anatomical plate group. There were 7 males and 5 females, ranging in age from 23 to 67 years in the external fixation with limited internal fixation group. The Ankle X-ray of Pilon fracture after operation, ankle score, early and late complications were collected. Bourne system was used to evaluate ankle joint function. After 8 months to 3 years follow-up, it was found that three kinds of treatment had significant differences in the outcomes and complications (P < 0.05): the external fixation with limited internal fixation group got the best results. The number of anatomic reduction cases in the external fixation with limited internal fixation group (7 cases) and the distal tibia anatomical plate group (8 cases) was more than the plaster immobilization group (2 cases). According to the ankle score, 8 patients got an excellent result, 3 good and 1 poor in the limited internal fixation group ,which was better than those of distal tibia anatomical plate group (5 excellent, 4 good and 2 poor) and the plaster immobilization group (3 excellent, 4 good and 3 poor). The number of early and late complications in the external fixation with limited internal fixation group was more than those in the plaster immobilization group and the distal tibia anatomical plate group (P< 0.05). Treatment of external fixation with limited internal fixation in the treatment of Pilon fracture of Rüedi-Allgower type III is effective and safe.

Safety and efficacy outcomes of long-term treatment up to 4 years with 5% lidocaine medicated plaster in patients with post-herpetic neuralgia.

PubMed

Sabatowski, Rainer; Hans, Guy; Tacken, Ingrid; Kapanadze, Sofia; Buchheister, Bettina; Baron, Ralf

2012-08-01

Prospective evaluation of the long-term efficacy and safety of the 5% lidocaine medicated plaster in patients with post-herpetic neuralgia (PHN). Patients with persisting pain for ≥3 months after acute herpes zoster and a baseline pain intensity of at least 4 on an 11-point numerical rating scale (NRS 0-10) were treated with 5% lidocaine medicated plasters for up to 5 years and monitored in regular intervals. Efficacy parameters are presented for the first 4 years and include patients' recall of pain relief (6-point verbal rating scale (VRS), clinical global impression of change (CGIC), patients' global impression of change PGIC), and the global evaluations of study medication. Safety parameters (clinical examination, skin evaluation, laboratory) and adverse events (AEs) were assessed at regular visits. KF10004/02. A total of 102 patients continuing from a 1 year main study period were included in an extension phase of up to 3 years. Ten patients (9.8%) dropped out due to lack of efficacy and 9 patients (8.8%) due to treatment-related AEs; 56 patients (54.9%) left the study for non-treatment-related reasons. Twenty-seven patients (26.4%) were still under treatment after a total treatment period of 4 years. On average, a pain relief of at least 4.3 (between moderate and a lot) was achieved throughout the study. At all visits the CGIC and the PGIC were much or very much improved in about 80% of patients. At the final visit, study medication was rated at least to be good by 91% of physicians and 89% of patients. Drug-related adverse events (DRAEs) were reported in 19 of 102 patients, mainly mild to moderate localized skin reactions. There were no hints for a reduced analgesic effect or an increase of DRAEs with long-term treatment. This study demonstrates that long-term treatment of ≥12 months with the 5% lidocaine medicated plaster is effective and well tolerated in PHN patients. These findings support the recommendations to use the 5% lidocaine medicated plaster as baseline therapy for localized neuropathic pain after herpes zoster infection (PHN).

Accuracy and precision of polyurethane dental arch models fabricated using a three-dimensional subtractive rapid prototyping method with an intraoral scanning technique

PubMed Central

Kim, Jae-Hong; Kim, Ki-Baek; Kim, Woong-Chul; Kim, Ji-Hwan

2014-01-01

Objective This study aimed to evaluate the accuracy and precision of polyurethane (PUT) dental arch models fabricated using a three-dimensional (3D) subtractive rapid prototyping (RP) method with an intraoral scanning technique by comparing linear measurements obtained from PUT models and conventional plaster models. Methods Ten plaster models were duplicated using a selected standard master model and conventional impression, and 10 PUT models were duplicated using the 3D subtractive RP technique with an oral scanner. Six linear measurements were evaluated in terms of x, y, and z-axes using a non-contact white light scanner. Accuracy was assessed using mean differences between two measurements, and precision was examined using four quantitative methods and the Bland-Altman graphical method. Repeatability was evaluated in terms of intra-examiner variability, and reproducibility was assessed in terms of inter-examiner and inter-method variability. Results The mean difference between plaster models and PUT models ranged from 0.07 mm to 0.33 mm. Relative measurement errors ranged from 2.2% to 7.6% and intraclass correlation coefficients ranged from 0.93 to 0.96, when comparing plaster models and PUT models. The Bland-Altman plot showed good agreement. Conclusions The accuracy and precision of PUT dental models for evaluating the performance of oral scanner and subtractive RP technology was acceptable. Because of the recent improvements in block material and computerized numeric control milling machines, the subtractive RP method may be a good choice for dental arch models. PMID:24696823

Reproducibility of the index of orthognathic functional treatment need scores derived from plaster study casts and their three-dimensional digital equivalents: a pilot study.

PubMed

McCrory, Emma; McGuinness, Niall Jp; Ulhaq, Aman

2018-06-01

To determine the reproducibility of Index of Orthognathic Functional Treatment Need (IOFTN) scores derived from plaster casts and their three-dimensional (3D) digital equivalents. Pilot study, prospective analytical. UK hospital orthodontic department. Thirty casts and their digital equivalents, representing the pre-treatment malocclusions of patients requiring orthodontic-orthognathic surgical treatment, were scored by four clinicians using IOFTN. Casts were scanned using a 3Shape digital scanner and 3D models produced using OrthoAnalyzer TM (3Shape Ltd, Copenhagen, Denmark). Examiners independently determined the IOFTN scores for the casts and digital models, to test their inter- and intra-operator reliability using weighted Kappa scores. Intra-operator agreement with IOFTN major categories (1-5: treatment need) was very good for plaster casts (0.83-0.98) and good-very good for digital models (0.78-0.83). Inter-operator agreement was moderate-very good for casts (0.58-0.82) and good-very good for digital models (0.65-0.92). Intra-operator agreement with IOFTN sub-categories (1-14: feature of malocclusion) was good-very good for casts (0.70-0.97) and digital models (0.80-0.94). Inter-operator agreement was moderate-good for casts (0.53-0.77); and moderate-very good for the digital models (0.58-0.90). Digital models are an acceptable alternative to plaster casts for examining the malocclusion of patients requiring combined orthodontic-orthognathic surgical treatment and determining treatment need.

Separation of overlapping dental arch objects using digital records of illuminated plaster casts.

PubMed

Yadollahi, Mohammadreza; Procházka, Aleš; Kašparová, Magdaléna; Vyšata, Oldřich; Mařík, Vladimír

2015-07-11

Plaster casts of individual patients are important for orthodontic specialists during the treatment process and their analysis is still a standard diagnostical tool. But the growing capabilities of information technology enable their replacement by digital models obtained by complex scanning systems. This paper presents the possibility of using a digital camera as a simple instrument to obtain the set of digital images for analysis and evaluation of the treatment using appropriate mathematical tools of image processing. The methods studied in this paper include the segmentation of overlapping dental bodies and the use of different illumination sources to increase the reliability of the separation process. The circular Hough transform, region growing with multiple seed points, and the convex hull detection method are applied to the segmentation of orthodontic plaster cast images to identify dental arch objects and their sizes. The proposed algorithm presents the methodology of improving the accuracy of segmentation of dental arch components using combined illumination sources. Dental arch parameters and distances between the canines and premolars for different segmentation methods were used as a measure to compare the results obtained. A new method of segmentation of overlapping dental arch components using digital records of illuminated plaster casts provides information with the precision required for orthodontic treatment. The distance between corresponding teeth was evaluated with a mean error of 1.38% and the Dice similarity coefficient of the evaluated dental bodies boundaries reached 0.9436 with a false positive rate [Formula: see text] and false negative rate [Formula: see text].

A new portable vibrator for plaster pouring: effect on the marginal fit at cylinder-abutment

PubMed Central

de ANDRADE, Pâmela Cândida Aires Ribas; LUTHI, Leonardo Flores; STANLEY, Kyle; CARDOSO, Antônio Carlos

2012-01-01

Objective The aim of this study was to test a new portable vibrator for plaster pouring (developed for this purpose), comparing the effect of its use on the accuracy of working cast of implant-supported restorations to the conventional vibrator. Material and methods From a master cast with 2 implants, 30 transfer moldings were made randomly and divided into three groups: Group I (GI): pouring performed in an outsourced dental laboratory with conventional plaster vibrator (10 casts), Group II (GII): pouring performed in the laboratory of the Federal University of Santa Catarina (UFSC) with conventional plaster vibrator (10 casts) and Group III (GIII): pouring performed with the portable vibrator fabricated for this study (10 casts). The position of the analogue and marginal adaptation of the infrastructure were verified by testing the single screw on the master model and on the working model. The measurement of misfit was blindly performed with a precision microscope and analyzing unit, Quadra-Check 200. The data were statistically analyzed by analysis of variance (ANOVA) and the Holm-Sidak test (α=0.05). Results Means±standard deviations were as follows: GI: 19.19±4.73 µm; GII: 21.72±5.41 µm; GIII: 13.5±2.39 µm (P<0.05), with GIII significantly lower as compared to the other groups. Conclusion Within the limitations of this study, it was concluded that a greater accuracy of working cast was achieved when a portable vibrator was used for casting molds. PMID:23138736

Durability of traditional plasters with respect to blast furnace slag-based plaster

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cerulli, T.; Pistolesi, C.; Maltese, C.

2003-09-01

Blast furnace slag is a residue of steel production. It is a latent hydraulic binder and is normally used to improve the durability of concrete and mortars. Slag could be also used as rendering mortar for masonry and old buildings. Today, cement and hydraulic lime are the most popular hydraulic binders used to make plasters. They are characterised by a low durability when exposed to the action of chemical and physical agents. The aim of this study was to provide a comparison between the physical-mechanical properties of some renders made with ordinary Portland cement, hydraulic lime, or slag. Furthermore, anmore » investigation was carried out to analyse mortar resistance to several aggressive conditions like acid attack, freezing and thawing cycles, abrasion, sulphate aggression, cycles in ultraviolet screening device, and salt diffusion. The specimens, after chemical attack, have been characterised from the chemical-physical [specific surface according to the BET (Brunauer-Emmet-Teller) method], crystal-chemical (X-ray diffraction, XRD), and morphological (scanning electron microscopy, SEM) points of view.« less

Severed cuff inflation tubing of endotracheal tube: A novel way to prevent cuff deflation.

PubMed

Rao, Amrut K; Chaudhuri, Souvik; Joseph, Tim T; Kamble, Deependra; Gotur, Gopal; Venkatesh, Sandeep

2014-01-01

A well-secured endotracheal tube (ETT) is essential for safe anesthesia. The ETT has to be fixed with the adhesive plasters or with tie along with adhesive plasters appropriately. It is specially required in patients having beard, in intensive care unit (ICU) patients or in oral surgeries. If re-adjustment of the ETT is necessary, we should be cautious while removal of the plasters and tie, as there may be damage to the cuff inflation system. This can be a rare cause of ETT cuff leak, thus making maintenance of adequate ventilation difficult and requiring re-intubation. In a difficult airway scenario, it can be extremely challenging to re-intubate again. We report an incidence where the ETT cuff tubing was severed while attempting to re-adjust and re-fix the ETT and the patient required re-intubation. Retrospectively, we thought of and describe a safe, reliable and novel technique to prevent cuff deflation of the severed inflation tube. The technique can also be used to monitor cuff pressure in such scenarios.

Silesia Dryvit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Presz, K.

1995-12-31

MT International, as a manufacturer and distributor for of US company named Dryvit Systems is focused on weatherization techniques as well as on facade and external wall finishing. The materials manufactured by Dryvit for building and construction purposes (plaster masses, building binders, insulating materials, reinforced fabric, etc.) are used at many sites. The consistent and well-selected composition of these materials guarantees highest quality of facade finishing in building structures of any type. The first implementation of Dryvit system in Warsaw was completed in 1974 and it remains the first exampled of professionally weatherized building in Poland. Different versions of Dryvitmore » system have been elaborated for various plaster base types. Consequently the assembling procedure differs, too. The main classification includes methods used directly on-site by a specialized contractor as well as prefabrication systems in which the ready-made elements prefabricated in a central plant or in a moveable unit are mounted on the walls. Distribution of materials and systems is based upon a network of branch offices and plaster mass mixter plants located in Warsaw, Szczecin, Lublin, Gdansk and Zabrze.« less

Review of Allergic and Photoallergic Contact Dermatitis from an Ingredient in a Medicament Vehicle Consisting of a Compress, Poultice, Plaster, and Tape

PubMed Central

Oiso, Naoki; Kawada, Akira

2011-01-01

The topical application of a medicament vehicle consisting of a compress, poultice, plaster, and tape containing a nonsteroidal anti-inflammatory drug or methyl salicylate is prevalent in Japan. The method is effective for conveying ingredients to the muscles via the skin for the relief of muscular pain. However, an ingredient in the occlusive vehicle can cause allergic and photoallergic contact dermatitis. We summarize cases reported over the past decade and discuss the current strategy for diminishing the risk of allergic and photoallergic contact dermatitis. PMID:21603165

A novel method for creating custom shaped ballistic gelatin trainers using plaster molds.

PubMed

Doctor, Michael; Katz, Anne; McNamara, Shannon O; Leifer, Jessica H; Bambrick-Santoyo, Gabriela; Saul, Turandot; Rose, Keith M

2018-03-01

Simulation based procedural training is an effective and frequently used method for teaching vascular access techniques which often require commercial trainers. These can be prohibitively expensive, which allows for homemade trainers made of gelatin to be a more cost-effective and attractive option. Previously described trainers are often rectangular with a flat surface that is dissimilar to human anatomy. We describe a novel method to create a more anatomically realistic trainer using ballistic gelatin, household items, and supplies commonly found in an emergency department such as the plaster wrap typically used to make splints.

Prosthesis Material

NASA Technical Reports Server (NTRS)

1995-01-01

FAB/CAM, a subsidiary of the Harshberger Prosthetic and Orthotic Center, Inc., approached Marshall for help in replacing the heavy, fragile plaster they used to produce master molds for prosthetics. Concurrently, Marshall and Martin Marietta were creating a commercial derivative of the foam insulation used to protect the Space Shuttle External Tank from excessive heat. FAB/CAM found the foam blanks to be lighter, cheaper and easier to manufacture than plaster, resulting in lower costs to the consumer. Martin Marietta markets the foam system, MARCORE, for the prosthesis market. The system also has commercial potential in high temperature insulation and structural applications.

Sustained compression and healing of chronic venous ulcers.

PubMed Central

Blair, S. D.; Wright, D. D.; Backhouse, C. M.; Riddle, E.; McCollum, C. N.

1988-01-01

STUDY OBJECTIVE--Comparison of four layer bandage system with traditional adhesive plaster bandaging in terms of (a) compression achieved and (b) healing of venous ulcers. DESIGN--Part of larger randomised trial of five different dressings. SETTING--Outpatient venous ulcer clinic in university hospital. PATIENTS--(a) Pressure exerted by both bandage systems was measured in the same 20 patients. (b) Healing with the four layer bandage was assessed in 148 legs in 126 consecutive patients (mean age 71 (SE 2); range 30-96) with chronic venous ulcers that had resisted treatment with traditional bandaging for a mean of 27.2 (SE 8) months. INTERVENTIONS--(a) Four layer bandage system or traditional adhesive plaster bandaging for pressure studies; (b) four layer bandaging applied weekly for studies of healing. END POINTS--(a) Comparison of pressures achieved at the ankle for up to one week; (b) complete healing within 12 weeks. MEASUREMENTS AND MAIN RESULTS--(a) Four layer bandage produced higher initial pressures at the ankle of 42.5 (SE 1) mm Hg compared with 29.8 (1.8) for the adhesive plaster (p less than 0.001; 95% confidence interval 18.5 to 6.9). Pressure was maintained for one week with the four layer bandage but fell to 10.4 (3.5) mm Hg at 24 hours with adhesive plaster bandaging. (b) After weekly bandaging with the four layer bandage 110 of 48 venous ulcers had healed completely within 12 (mean 6.3 (0.4)) weeks. CONCLUSION--Sustained compression of over 40 mm Hg achieved with a multilayer bandage results in rapid healing of chronic venous ulcers that have failed to heal in many months of compression at lower pressures with more conventional bandages. PMID:3144330

Comparison of effects of seven treatment methods for distal radius fracture on minimizing complex regional pain syndrome

PubMed Central

Sun, Tao

2016-01-01

Introduction Using network meta-analysis, we evaluated the adverse effects of the seven most common treatment methods, i.e., bridging external fixation, non-bridging external fixation, K-wire fixation, plaster fixation, dorsal plating, volar plating, and dorsal and volar plating, by their associated risk of developing complex regional pain syndrome (CRPS) in distal radius fracture (DRF) patients. Material and methods Following an exhaustive search of scientific literature databases for high quality studies, randomized controlled trials (RCTs) related to our study topic were screened and selected based on stringent predefined inclusion and exclusion criteria. Data extracted from the selected studies were used for statistical analyses using Stata 12.0 software. Results A total of 17 RCTs, including 1658 DRF patients, were enrolled in this network meta-analysis. Among the 1658 DRF patients, 452 received bridging external fixation, 525 received non-bridging external fixation, 154 received K-wire fixation, 84 received plaster fixation, 132 received dorsal plating, 123 received volar plating, and 188 received dorsal and volar plating. When compared to bridging external fixation patients, there was no marked difference in the CRPS risk in DRF patients receiving different treatments (all p > 0.05). However, the surface under the cumulative ranking curves (SUCRA) for plaster fixation (77.0%) and non-bridging external fixation (71.3%) were significantly higher compared with the other five methods. Conclusions Our findings suggest that compared with bridging external fixation, K-wire fixation, dorsal plating, volar plating, dorsal and volar plating, plaster fixation and non-bridging external fixation might be the better treatment methods to reduce the risk of CRPS in DRF patients. PMID:28144268

Accuracy of five implant impression technique: effect of splinting materials and methods

PubMed Central

Cho, Sung-Bum

2011-01-01

PURPOSE The aim of this study was to evaluate the effect of dimensional stability of splinting material on the accuracy of master casts. MATERIALS AND METHODS A stainless steel metal model with 6 implants embedded was used as a master model. Implant level impressions were made after square impression copings were splinted using 5 different techniques as follows. (1) Splinted with autopolymerizing resin and sectioned, reconnected to compensate polymerization shrinkage before the impression procedure. (2) Splinted with autopolymerizing resin just before impression procedure. (3) Primary impression made with impression plaster and secondary impression were made over with polyether impression material. (4) Splinted with impression plaster. (5) Splinted with VPS bite registration material. From master model, 5 impressions and 5 experimental casts, total 25 casts were made for each of 5 splinting methods. The distortion values of each splinting methods were measured using coordinate measuring machine, capable of recordings in the x-, y-, z-axes. A one-way analysis of variance (ANOVA) at a confidence level of 95% was used to evaluate the data and Tukey's studentized range test was used to determine significant differences between the groups. RESULTS Group 1 showed best accuracy followed by Group 3 & 4. Group 2 and 5 showed relatively larger distortion value than other groups. No significant difference was found between group 3, 4, 5 in x-axis, group 2, 3, 4 in y-axis and group 1, 3, 4, 5 in z-axis (P<.0001). CONCLUSION Both Splinting impression copings with autopolymerizing resin following compensation of polymerization shrinkage and splinting method with impression plaster can enhance the accuracy of master cast and impression plaster can be used simple and effective splinting material for implant impression procedure. PMID:22259700

The Accuracy and Reproducibility of Linear Measurements Made on CBCT-derived Digital Models.

PubMed

Maroua, Ahmad L; Ajaj, Mowaffak; Hajeer, Mohammad Y

2016-04-01

To evaluate the accuracy and reproducibility of linear measurements made on cone-beam computed tomography (CBCT)-derived digital models. A total of 25 patients (44% female, 18.7 ± 4 years) who had CBCT images for diagnostic purposes were included. Plaster models were obtained and digital models were extracted from CBCT scans. Seven linear measurements from predetermined landmarks were measured and analyzed on plaster models and the corresponding digital models. The measurements included arch length and width at different sites. Paired t test and Bland-Altman analysis were used to evaluate the accuracy of measurements on digital models compared to the plaster models. Also, intraclass correlation coefficients (ICCs) were used to evaluate the reproducibility of the measurements in order to assess the intraobserver reliability. The statistical analysis showed significant differences on 5 out of 14 variables, and the mean differences ranged from -0.48 to 0.51 mm. The Bland-Altman analysis revealed that the mean difference between variables was (0.14 ± 0.56) and (0.05 ± 0.96) mm and limits of agreement between the two methods ranged from -1.2 to 0.96 and from -1.8 to 1.9 mm in the maxilla and the mandible, respectively. The intraobserver reliability values were determined for all 14 variables of two types of models separately. The mean ICC value for the plaster models was 0.984 (0.924-0.999), while it was 0.946 for the CBCT models (range from 0.850 to 0.985). Linear measurements obtained from the CBCT-derived models appeared to have a high level of accuracy and reproducibility.

Treatment of wrist and hand fractures with natural magnets: preliminary report.

PubMed

Costantino, Cosimo; Pogliacomi, Francesco; Passera, Francesco; Concari, Galeazzo

2007-12-01

The Authors, after having defined the phenomenon and the biological characteristics of natural magnets, evaluate their ability in accelerating the formation of bone callus in hand and wrist fractures compared to treatment with immobilization in a plaster cast. Forty patients (4 females and 37 males) between 20 and 86 years of age were treated. A small natural magnet was inserted in each of the plaster casts (diameter: 2cm, height: 0.5cm) made of 4 blocks in Neodymium-Iron-Boron, capable of generating 4 magnetic poles (2 positive and 2 negative) of diagonal alternate polarity that produced a symmetric, quadruple static magnetic field. The created magnetic flow was wavelike, concentrated in one direction, and developed a force up to 12,500 gauss. From this study it has emerged that inserting a quadruple magnet in a plaster cast in hand and wrist fractures results in the formation of bone callus in an average time that is 35% inferior to the "standard" time. Accelerating the healing of the fracture is important since it reduces immobilization time for the joints involved, avoiding subsequent weakness and stiffness and allowing the patient to begin rehabilitative physiotherapy sooner, which permits a faster functional recovery.

The Aspects About of Objectively Appraisals of Modeling Gypsum Quality and Composites of Phonic-Absorbent and Orthopedic on Base of Gypsum

NASA Astrophysics Data System (ADS)

Pop, P. A.; Ungur, P. A.; Lazar, L.; Marcu, F.

2009-11-01

The EU Norms about of protection environment, outside and inside ambient, and human health demands has lead at obtain of new materials on the base of airborne material, with high thermo and phonic-absorbent properties, porous and lightweight. The α and β-modeling gypsum plaster quality and lightweight depend on many factors as: fabrication process, granulation, roast temperature, work temperature, environment, additives used, breakage, etc. Also, the objectively appraisal of modeling gypsum quality depends of proper tests methods selection, which are legislated in norms, standards and recommendations. In Romanian Standards SR EN 13279-1/2005 and SR EN 13279-2/2005, adaptable from EU Norms EN 13279-1/2004 and EN 13279-2/2004, the characteristics gypsum family tests are well specification, as: granule-metric analysis, determination of water/plaster ratio, setting time, mechanical characteristics, adhesions and water restrain. For plaster with special use (phonic-absorbent and orthopedic materials, etc.) these determinations are not concluding, being necessary more parameters finding, as: elastic constant, phonic-absorbent coefficient, porosity, working, etc., which is imposed the completion of norms and standards with new determinations.

Tooth-size discrepancy: A comparison between manual and digital methods

PubMed Central

Correia, Gabriele Dória Cabral; Habib, Fernando Antonio Lima; Vogel, Carlos Jorge

2014-01-01

Introduction Technological advances in Dentistry have emerged primarily in the area of diagnostic tools. One example is the 3D scanner, which can transform plaster models into three-dimensional digital models. Objective This study aimed to assess the reliability of tooth size-arch length discrepancy analysis measurements performed on three-dimensional digital models, and compare these measurements with those obtained from plaster models. Material and Methods To this end, plaster models of lower dental arches and their corresponding three-dimensional digital models acquired with a 3Shape R700T scanner were used. All of them had lower permanent dentition. Four different tooth size-arch length discrepancy calculations were performed on each model, two of which by manual methods using calipers and brass wire, and two by digital methods using linear measurements and parabolas. Results Data were statistically assessed using Friedman test and no statistically significant differences were found between the two methods (P > 0.05), except for values found by the linear digital method which revealed a slight, non-significant statistical difference. Conclusions Based on the results, it is reasonable to assert that any of these resources used by orthodontists to clinically assess tooth size-arch length discrepancy can be considered reliable. PMID:25279529

Effects of adhesive dressings on stratum corneum conductance.

PubMed

Cavallini, Maurizio; Gazzola, Riccardo; Vaienti, Luca

2012-05-01

Stratum corneum is a fundamental layer of epidermis. It acts as a barrier, with antimicrobial features, regulating skin permeability and integrity as well. Adhesive dressings and their removal could alter this layer, affecting cutaneous water balance and lipid composition of stratum corneum. These changes could be monitored by measurement of cutaneous hydration. Ninety-two patients affected by wounds dressed with adhesive tapes or plasters have been studied. Measurement of skin conductance under tape/plaster and in the surrounding healthy skin, immediately after removal of dressing has been performed. Dressing age, wound localization, and characteristics were also considered. Adhesive dressings alter significantly stratum corneum conductance. Although healthy skin hydration has significant variations throughout the body, cutaneous conductance under adhesive dressing in different areas displays no significative changes. Moreover, the increase in hydration due to adhesive tapes/plasters showed no association with wound dehiscence. Adhesive dressings cause a significative increase in stratum corneum conductance, acting as a barrier to apocrine secretions. Although different hydration levels have been observed in healthy skin throughout the body, no difference exists under adhesive dressing among different regions, suggesting no contraindications in their employment throughout the body. Increase in cutaneous hydration showed no correlations with wound dehiscence, thus confirming safety and practicality of these dressings. © 2011 John Wiley & Sons A/S.

Plastering mortar with antibacterial and antifungal properties studied by 1H NMR relaxometry

NASA Astrophysics Data System (ADS)

Jumate, E.; Aciu, C.; Manea, D. L.; Moldovan, D.; Chelcea, R.; Fechete, R.

2017-12-01

The Plastering mortars, with good antibacterial (in particular Escherichia coli, Staphylococcus aureus, Enterococcus faecalis, Pseudomonas aeruginosa) and antifungal (Aspergillus niger and Penicillium chrysogenum) properties, were studied by 1D NMR relaxometry and internal humidity measurements. Three recipes based on plastering mortar with variable content (0, 5 and 10 %) of Ag/ZnO nanopowders and with adequate physical characteristics regarding the mechanical strengths (CS IV), good adhesion to the substrate and low water absorption by capillarity (W2) were considered. The distributions of transverse relaxation times T2 were measured at 2 h after preparation (for mortar pasta) and then for the same samples at 2, 7, and 28 days during the hydration of mineralogical components. The T2 distributions are characterized by four components associated with hydration water and water in three types of pores of different dimension. The dimension of pores formed during hydration process are strongly dependent on the Ag/ZnO nanopowders content but finally at 28 days the pores distributions, as resulted from the T2 distributions, looks similar. Finally, the transverse relaxation ratio was linearly correlated to the compressive strength and the hydration behaviour during 132 days measured with a dedicated humidity sensor embedded inside sampled was discussed.

Populations of some molds in water-damaged homes may differ if the home was constructed with gypsum drywall compared to plaster.

PubMed

Vesper, Stephen; Wymer, Larry; Cox, David; Dewalt, Gary

2016-08-15

Starting in the 1940s, gypsum drywall began replacing plaster and lathe in the U.S. home construction industry. Our goal was to evaluate whether some mold populations differ in water- damaged homes primarily constructed with gypsum drywall compared to plaster. The dust samples from the 2006 Department of Housing and Urban Development's (HUD) American Health Homes Survey (AHHS) were the subject of this analysis. The concentrations of the 36 Environmental Relative Moldiness Index (ERMI) molds were compared in homes of different ages. The homes (n=301) were built between 1878 and 2005. Homes with ERMI values >5 (n=126) were defined as water-damaged. Homes with ERMI values >5 were divided in the years 1976 to 1977 into two groups, i.e., older (n=61) and newer (n=65). Newer water-damaged homes had significantly (p=0.002) higher mean ERMI values than older water-damaged homes, 11.18 and 8.86, respectively. The Group 1 molds Aspergillus flavus, Ammophilus fumigatus, Aspergillus ochraceus, Cladosporium sphaerospermum and Trichoderma viride were found in significantly higher concentrations in newer compared to older high-ERMI homes. Some mold populations in water-damaged homes may have changed after the introduction of gypsum drywall. Published by Elsevier B.V.

Efficiency and Safety: The Best Time to Valve a Plaster Cast.

PubMed

Steiner, Samuel R H; Gendi, Kirollos; Halanski, Matthew A; Noonan, Kenneth J

2018-04-18

The act of applying, univalving, and spreading a plaster cast to accommodate swelling is commonly performed; however, cast saws can cause thermal and/or abrasive injury to the patient. This study aims to identify the optimal time to valve a plaster cast so as to reduce the risk of cast-saw injury and increase spreading efficiency. Plaster casts were applied to life-sized pediatric models and were univalved at set-times of 5, 8, 12, or 25 minutes. Outcome measures included average and maximum force applied during univalving, blade-to-skin touches, cut time, force needed to spread, number of spread attempts, spread completeness, spread distance, saw blade temperature, and skin surface temperature. Casts allowed to set for ≥12 minutes had significantly fewer blade-to-skin touches compared with casts that set for <12 minutes (p < 0.001). For average and maximum saw blade force, no significant difference was observed between individual set-times. However, in a comparison of the shorter group (<12 minutes) and the longer group (≥12 minutes), the longer group had a higher average force (p = 0.009) but a lower maximum force (p = 0.036). The average temperature of the saw blade did not vary between groups. The maximum force needed to "pop," or spread, the cast was greater for the 5-minute and 8-minute set-times. Despite requiring more force to spread the cast, 0% of attempts at 5 minutes and 54% of attempts at 8 minutes were successful in completely spreading the cast, whereas 100% of attempts at 12 and 25 minutes were successful. The spread distance was greatest for the 12-minute set-time at 5.7 mm. Allowing casts to set for 12 minutes is associated with decreased blade-to-skin contact, less maximum force used with the saw blade, and a more effective spread. Adherence to the 12-minute interval could allow for fewer cast-saw injuries and more effective spreading.

Sampling methods in archaeomagnetic dating: A comparison using case studies from Wörterberg, Eisenerz and Gams Valley (Austria)

NASA Astrophysics Data System (ADS)

Trapanese, A.; Batt, C. M.; Schnepp, E.

The aim of this research was to review the relative merits of different methods of taking samples for archaeomagnetic dating. To allow different methods to be investigated, two archaeological structures and one modern fireplace were sampled in Austria. On each structure a variety of sampling methods were used: the tube and disc techniques of Clark et al. (Clark, A.J., Tarling, D.H., Noel, M., 1988. Developments in archaeomagnetic dating in Great Britain. Journal of Archaeological Science 15, 645-667), the drill core technique, the mould plastered hand block method of Thellier, and a modification of it. All samples were oriented with a magnetic compass and sun compass, where weather conditions allowed. Approximately 12 discs, tubes, drill cores or plaster hand blocks were collected from each structure, with one mould plaster hand block being collected and cut into specimens. The natural remanent magnetisation (NRM) of the samples was measured and stepwise alternating field (AF) or thermal demagnetisation was applied. Samples were measured either in the UK or in Austria, which allowed the comparison of results between magnetometers with different sensitivity. The tubes and plastered hand block specimens showed good agreement in directional results, and the samples obtained showed good stability. The discs proved to be unreliable as both NRM and the characteristic remanent magnetisation (ChRM) distribution were very scattered. The failure of some methods may be related to the suitability of the material sampled, for example if it was disturbed before sampling, had been insufficiently heated or did not contain appropriate magnetic minerals to retain a remanent magnetisation. Caution is also recommended for laboratory procedures as the cutting of poorly consolidated specimens may disturb the material and therefore the remanent magnetisation. Criteria and guidelines were established to aid researchers in selecting the most appropriate method for a particular archaeological structure.

Evaluation of the iPhone with an acrylic sleeve versus the Scoliometer for rib hump measurement in scoliosis.

PubMed

Izatt, Maree T; Bateman, Gary R; Adam, Clayton J

2012-07-30

Vertebral rotation found in structural scoliosis contributes to trunkal asymmetry which is commonly measured with a simple Scoliometer device on a patient's thorax in the forward flexed position. The new generation of mobile 'smartphones' have an integrated accelerometer, making accurate angle measurement possible, which provides a potentially useful clinical tool for assessing rib hump deformity. This study aimed to compare rib hump angle measurements performed using a Smartphone and traditional Scoliometer on a set of plaster torsos representing the range of torsional deformities seen in clinical practice. Nine observers measured the rib hump found on eight plaster torsos moulded from scoliosis patients with both a Scoliometer and an Apple iPhone on separate occasions. Each observer repeated the measurements at least a week after the original measurements, and were blinded to previous results. Intra-observer reliability and inter-observer reliability were analysed using the method of Bland and Altman and 95% confidence intervals were calculated. The Intra-Class Correlation Coefficients (ICC) were calculated for repeated measurements of each of the eight plaster torso moulds by the nine observers. Mean absolute difference between pairs of iPhone/Scoliometer measurements was 2.1 degrees, with a small (1 degrees) bias toward higher rib hump angles with the iPhone. 95% confidence intervals for intra-observer variability were +/- 1.8 degrees (Scoliometer) and +/- 3.2 degrees (iPhone). 95% confidence intervals for inter-observer variability were +/- 4.9 degrees (iPhone) and +/- 3.8 degrees (Scoliometer). The measurement errors and confidence intervals found were similar to or better than the range of previously published thoracic rib hump measurement studies. The iPhone is a clinically equivalent rib hump measurement tool to the Scoliometer in spinal deformity patients. The novel use of plaster torsos as rib hump models avoids the variables of patient fatigue and discomfort, inconsistent positioning and deformity progression using human subjects in a single or multiple measurement sessions.

Evaluation of the iPhone with an acrylic sleeve versus the Scoliometer for rib hump measurement in scoliosis

PubMed Central

2012-01-01

Background Vertebral rotation found in structural scoliosis contributes to trunkal asymmetry which is commonly measured with a simple Scoliometer device on a patient's thorax in the forward flexed position. The new generation of mobile 'smartphones' have an integrated accelerometer, making accurate angle measurement possible, which provides a potentially useful clinical tool for assessing rib hump deformity. This study aimed to compare rib hump angle measurements performed using a Smartphone and traditional Scoliometer on a set of plaster torsos representing the range of torsional deformities seen in clinical practice. Methods Nine observers measured the rib hump found on eight plaster torsos moulded from scoliosis patients with both a Scoliometer and an Apple iPhone on separate occasions. Each observer repeated the measurements at least a week after the original measurements, and were blinded to previous results. Intra-observer reliability and inter-observer reliability were analysed using the method of Bland and Altman and 95% confidence intervals were calculated. The Intra-Class Correlation Coefficients (ICC) were calculated for repeated measurements of each of the eight plaster torso moulds by the nine observers. Results Mean absolute difference between pairs of iPhone/Scoliometer measurements was 2.1 degrees, with a small (1 degrees) bias toward higher rib hump angles with the iPhone. 95% confidence intervals for intra-observer variability were +/- 1.8 degrees (Scoliometer) and +/- 3.2 degrees (iPhone). 95% confidence intervals for inter-observer variability were +/- 4.9 degrees (iPhone) and +/- 3.8 degrees (Scoliometer). The measurement errors and confidence intervals found were similar to or better than the range of previously published thoracic rib hump measurement studies. Conclusions The iPhone is a clinically equivalent rib hump measurement tool to the Scoliometer in spinal deformity patients. The novel use of plaster torsos as rib hump models avoids the variables of patient fatigue and discomfort, inconsistent positioning and deformity progression using human subjects in a single or multiple measurement sessions. PMID:22846346

Damage monitoring in historical murals by speckle interferometry

NASA Astrophysics Data System (ADS)

Hinsch, Klaus D.; Gulker, Gerd; Joost, Holger

2003-11-01

In the conservation of historical murals it is important to identify loose plaster sections that threaten to fall off. Electronic speckle interferometry in combination with acoustic excitation of the object has been employed to monitor loose areas. To avoid disadvantages of high sound irradiation of the complete building a novel directional audio-sound source based on nonlinear mixing of ultrasound has been introduced. The optical system was revised for optimum performance in the new environment. Emphasis is placed on noise suppression to increase sensitivity. Furthermore, amplitude and phase data of object response over the frequency-range inspected are employed to gain additional information on the state of the plaster or paint. Laboratory studies on sample specimen supplement field campaigns at historical sites.

Comparing Composites.

ERIC Educational Resources Information Center

Mathras, Michael S.

1993-01-01

Presents an activity that models the work of chemical engineers. Students design, fabricate, and perform mechanical tests on plaster matrix composites and compare the strength to mass ratios of several products. (PR)

MEASUREMENT OF RADON, THORON AND THEIR PROGENY IN DIFFERENT TYPES OF DWELLING IN ALMORA DISTRICT OF KUMAUN HIMALAYAN REGION.

PubMed

Singh, Kuldeep; Semwal, Poonam; Pant, Preeti; Gusain, G S; Joshi, Manish; Sapra, B K; Ramola, R C

2016-10-01

The indoor concentrations of radon ( 222 Rn), thoron ( 220 Rn) and their daughter products were measured in the dwellings of Almora district in Kumaun Himalaya, India using pin-hole dosemeters and deposition progeny sensors. The measurements were made in the residential houses built of mud, stone with cement plaster and cemented house during winter season. Average [geometric mean (GM) values] radon and thoron concentrations for all dwellings were found to be 99.82 and 79.70 Bq m -3 , respectively, while average equilibrium equivalent radon concentration and equilibrium equivalent thoron concentration (measured for the first time for this region) were measured at 35.22 and 2.52 Bq m -3 , respectively. Radon concentration (GM values) was found to be 110.73, 97.00 and 93.85 Bq m -3 for mud houses, stone with cemented plaster houses and cemented houses, respectively. On the other hand, thoron concentration values were 87.10, 75.79 and 75.68 Bq m -3 for cemented houses, mud houses and stone with cemented plaster houses, respectively. Interpretations have been made on the basis of measured radon/thoron and progeny concentration values with respect to the difference of construction material of the dwellings. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Treatment of unstable intraarticular fracture of distal radius: POP casting with external fixation.

PubMed

ur Rahman, Obaid; Khan, Mohammad Qadeem; Rasheed, Haroon; Ahmad, Saleem

2012-04-01

To compare radiological and functional outcome of external fixation and distraction with conservative Plaster of Paris (POP) cast for unstable intra-articular fractures of the distal radius. The study was conducted on 60 patients with unstable intra-articular fracture of distal radius who reported to emergency or outpatient Orthopaedic Surgery department of Benazir Bhutto Hospital, Rawalpindi, between March and August 2007. They were divided into two equal groups: Group A and Group B, treated by Plaster of Paris cast, and external fixation with distraction respectively. The functional outcome in terms of freedom from pain, range of movement, grip power and deformity, and the radiological outcome of radial length, incongruity and radio-ulnar joint position were analysed at three months follow-up using a 3-point scoring scale. In Group A, 1 (3%) patient showed excellent result, 8 (27%) patients good results, 19 (63%) patients fair results and 2 (7%) patients poor result. In Group B, 14 (47%) patients showed excellent results, 11 (37%) patients good results, 4 (13%) patients fair results and 1 (3%) patient poor result. The outcome score of the Group B patients was significantly better compared to the Group A patients (p value < 0.05). External fixation has definite advantages over conventional Plaster of Paris cast in the treatment of unstable intra-articular fractures of distal radius.

Steel slag: a waste industrial by-product as an alternative sustainable green building material in construction applications--an attempt for solid waste management.

PubMed

Pofale, Arun D; Nadeem, Mohammed

2012-01-01

This investigation explores the possibility of utilizing granular slag as an alternative to fine aggregate (natural sand) in construction applications like masonry and plastering. Construction industry utilizes large volume of fine aggregate in all the applications which has resulted into shortage of good quality naturally available fine aggregate. Use of granular slag serves two fold purposes, i.e. waste utilisation as well as alternative eco-friendly green building material for construction. The investigation highlights comparative study of properties with partial and full replacement of fine aggregate (natural sand) by granular slag in cement mortar applications (masonry and plastering). For this purpose, cement mortar mix proportions from 1:3, 1:4, 1:5 & 1:6 by volume were selected for 0, 25, 50, 75 & 100% replacement levels with w/c ratios of 0.60, 0.65, 0.70 & 0.72 respectively. Based on the study results, it could be inferred that replacement of natural sand with granular slag from 25 to 75% increased the packing density of mortar which resulted into reduced w/c ratio, increased strength properties of all mortar mixes. Hence, it could be recommended that the granular slag could be effectively utilized as fine aggregate in masonry and plastering applications in place of conventional cement mortar mixes using natural sand.

Axial compression behaviour of reinforced wallettes fabricated using wood-wool cement panel

NASA Astrophysics Data System (ADS)

Noh, M. S. Md; Kamarudin, A. F.; Mokhatar, S. N.; Jaudin, A. R.; Ahmad, Z.; Ibrahim, A.; Muhamad, A. A.

2018-04-01

Wood-wool cement composite panel (WWCP) is one of wood based composite material that produced in a stable panel form and suitable to be used as building wall system to replace non-ecofriendly material such as brick and other masonry element. Heavy construction material such as brick requires more manpower and consume a lot of time to build the wall panel. WWCP is a lightweight material with a density range from 300 kg/m3 to 500 kg/m3 and also capable to support an imposed load from the building. This study reported on the axial compression behaviour of prefabricated reinforced wallettes constructed with wood-wool cement panel. A total of six specimens were fabricated using two layers of cross laminated WWCP bonded with normal mortar paste (Portland cement) at a mix ratio of 1:3 (cement : sand). As part of lifting mechanism, the wallettes were equipped with three steel reinforcement (T12) that embedded inside the core of wallettes. Three replicates of wallettes specimens with dimension 600 mm width and 600 mm length were fabricated without surface plaster and with 16 mm thickness of surface plaster. The wallettes were tested under axial compression load after 28 days of fabrication until failure. The result indicated that, the application of surface plaster significantly increases the loading capacity about 35 % and different orientation of the panels improve the bonding strength of the wall.

The regulation of crystalline silica: an industry perspective.

PubMed

Elzea, J M

1997-01-01

Silica is ubiquitous in the earth's crust. It occurs in trace to large quantities in rocks and soil. Because it is so common, the regulation of silica has affected a large number of industries, including the mining industry and any industry that uses quartz in the manufacture of a products. Mineral commodities that contain silica include diatomite, bentonite, kaolinite, talc, pyrophyllite, sand and gravel, perlite, pumice, dimension stone, and barite. Products that contain minerals, many of which are associated with silica, include paint, paper, rubber, plastic, pharmaceuticals, food, cement, plaster, cat litter, potting soil, plaster board, and miscellaneous construction materials. In collaboration with some agencies and academic centers, the silica industry is supporting research to lower health risks and to improve the methods of detecting this common material.

[Computer aided design and 3-dimensional printing for the production of custom trays of maxillary edentulous jaws based on 3-dimensional scan of primary impression].

PubMed

Chen, H; Zhao, T; Wang, Y; Sun, Y C

2016-10-18

To establish a digital method for production of custom trays for edentulous jaws using fused deposition modeling (FDM) based on three-dimensional (3D) scans of primary jaw impressions, and to quantitatively evaluate the accuracy. A red modeling compound was used to make a primary impression of a standard maxillary edentulous plaster model. The plaster model data and the primary impression tissue surface data were obtained using a 3D scanner. In the Gemomagic 2012 software, several commands were used, such as interactive drawing curves, partial filling holes, local offset, bodily offset, bodily shell, to imitate clinical procedures of drawing tray boundary, filling undercut, buffer, and generating the tray body. A standard shape of tray handle was designed and attached to the tray body and the data saved as stereolithography (STL) format. The data were imported into a computer system connected to a 3D FDM printing device, and the custom tray for the edentulous jaw model was printed layer upon layer at 0.2 mm/layer, using polylactic acid (PLA) filament, the tissue surface of the tray was then scanned with a 3D scanner. The registration functions of Geomagic 2012 was used to register the 3-dimentional surface data, and the point-cloud deviation analysis function of the Imageware 13.0 system was used to analyze the error. The CAD data of the custom tray was registered to the scan data, and the error between them was analyzed. The scanned plaster model surface was registered to the scanned impression surface and the scanned tray data to the CAD data, then the distance between the surface of plaster model and the scanned tissue surface of the custom tray was measured in Imageware 13.0. The deviation between the computer aided design data and the scanned data of the custom tray was (0.17±0.20) mm, with (0.19±0.18) mm in the primary stress-bearing area, (0.17±0.22) mm in the secondary stress-bearing area, (0.30±0.29) mm in the border seal area, (0.08±0.06) mm in the buffer area; the space between the tissue faces of the plaster model and the scanned tissue surface of custom tray was (1.98±0.40) mm, with (1.85±0.24) mm in the primary stress-bearing area, (1.86±0.26) mm in the secondary stress-bearing area, (1.77±0.36) mm in the border seal area, (2.90±0.26) mm in the buffer area. With 3D scanning, computer aided design and FDM technology, an efficient means of custom tray production was established.

Presidential Green Chemistry Challenge: 2010 Designing Greener Chemicals Award

EPA Pesticide Factsheets

Presidential Green Chemistry Challenge 2010 award winner, Clarke, developed Natular, a plaster matrix that encapsulates the pesticide spinosad, slowly releasing it into water and effectively controlling mosquito larvae.

21 CFR 358.103 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... USE MISCELLANEOUS EXTERNAL DRUG PRODUCTS FOR OVER-THE-COUNTER HUMAN USE Wart Remover Drug Products... skin in a thin layer. (c) Plaster vehicle. A fabric, plastic, or other suitable backing material in...

21 CFR 358.103 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (nitrocellulose) in an appropriate nonaqueous solvent that leaves a transparent cohesive film when applied to the skin in a thin layer. (c) Plaster vehicle. A fabric, plastic, or other suitable backing material in...

21 CFR 358.503 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... film when applied to the skin in a thin layer. (c) Plaster vehicle. A fabric, plastic, or other suitable backing material in which medication is usually incorporated for topical application to the skin. ...

21 CFR 358.503 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-04-01

... film when applied to the skin in a thin layer. (c) Plaster vehicle. A fabric, plastic, or other suitable backing material in which medication is usually incorporated for topical application to the skin. ...

21 CFR 358.503 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... film when applied to the skin in a thin layer. (c) Plaster vehicle. A fabric, plastic, or other suitable backing material in which medication is usually incorporated for topical application to the skin. ...

21 CFR 358.503 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-04-01

... film when applied to the skin in a thin layer. (c) Plaster vehicle. A fabric, plastic, or other suitable backing material in which medication is usually incorporated for topical application to the skin. ...

27. Historic American Buildings Survey Albert S. Burns, Photographer September ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

27. Historic American Buildings Survey Albert S. Burns, Photographer September 30, 1935. PLASTER CORNICE - MUSIC ROOM - The Maples, 630 South Carolina Avenue Southeast, Washington, District of Columbia, DC

21 CFR 358.503 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... film when applied to the skin in a thin layer. (c) Plaster vehicle. A fabric, plastic, or other suitable backing material in which medication is usually incorporated for topical application to the skin. ...

Comparison of the spatial landmark scatter of various 3D digitalization methods.

PubMed

Boldt, Florian; Weinzierl, Christian; Hertrich, Klaus; Hirschfelder, Ursula

2009-05-01

The aim of this study was to compare four different three-dimensional digitalization methods on the basis of the complex anatomical surface of a cleft lip and palate plaster cast, and to ascertain their accuracy when positioning 3D landmarks. A cleft lip and palate plaster cast was digitalized with the SCAN3D photo-optical scanner, the OPTIX 400S laser-optical scanner, the Somatom Sensation 64 computed tomography system and the MicroScribe MLX 3-axis articulated-arm digitizer. First, four examiners appraised by individual visual inspection the surface detail reproduction of the three non-tactile digitalization methods in comparison to the reference plaster cast. The four examiners then localized the landmarks five times at intervals of 2 weeks. This involved simply copying, or spatially tracing, the landmarks from a reference plaster cast to each model digitally reproduced by each digitalization method. Statistical analysis of the landmark distribution specific to each method was performed based on the 3D coordinates of the positioned landmarks. Visual evaluation of surface detail conformity assigned the photo-optical digitalization method an average score of 1.5, the highest subjectively-determined conformity (surpassing computer tomographic and laser-optical methods). The tactile scanning method revealed the lowest degree of 3D landmark scatter, 0.12 mm, and at 1.01 mm the lowest maximum 3D landmark scatter; this was followed by the computer tomographic, photo-optical and laser-optical methods (in that order). This study demonstrates that the landmarks' precision and reproducibility are determined by the complexity of the reference-model surface as well as the digital surface quality and individual ability of each evaluator to capture 3D spatial relationships. The differences in the 3D-landmark scatter values and lowest maximum 3D-landmark scatter between the best and the worst methods showed minor differences. The measurement results in this study reveal that it is not the method's precision but rather the complexity of the object analysis being planned that should determine which method is ultimately employed.

Dry solution to a sticky problem

PubMed Central

KARP, JEFFREY M.; LANGER, ROBERT

2011-01-01

Sticking plasters revolutionized the protection of minor wounds, but they’re not ideal for fragile skin. A material that mimics the adhesive properties of certain beetles’ feet might provide a solution. PMID:21886155

Ways.

ERIC Educational Resources Information Center

Finnucan, Donna; And Others

1985-01-01

Describes an elementary art program that teaches children to use clay, a course in which middle-grade students made pottery using old plaster greenware molds, and an art class in which middle-grade students made Indian jewelry. (RM)

Pieces of the Past.

ERIC Educational Resources Information Center

Carlson, Kenneth W.

1994-01-01

Discusses and presents activities for learning about plant fossils. The first activity uses teacher-prepared "fossils" made from plaster of Paris. Students attempt to classify the plants. In the second activity, students observe actual plant fossils. (PR)

48 CFR 852.236-79 - Daily report of workers and material.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., mechanics, foremen/forewomen and pieces of heavy equipment used or employed by the contractor and... concrete, plastering, masonry, plumbing, sheet metal work, etc. The report shall give a breakdown of...

48 CFR 852.236-79 - Daily report of workers and material.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., mechanics, foremen/forewomen and pieces of heavy equipment used or employed by the contractor and... concrete, plastering, masonry, plumbing, sheet metal work, etc. The report shall give a breakdown of...

48 CFR 852.236-79 - Daily report of workers and material.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., mechanics, foremen/forewomen and pieces of heavy equipment used or employed by the contractor and... concrete, plastering, masonry, plumbing, sheet metal work, etc. The report shall give a breakdown of...

48 CFR 852.236-79 - Daily report of workers and material.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., mechanics, foremen/forewomen and pieces of heavy equipment used or employed by the contractor and... concrete, plastering, masonry, plumbing, sheet metal work, etc. The report shall give a breakdown of...

48 CFR 852.236-79 - Daily report of workers and material.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., mechanics, foremen/forewomen and pieces of heavy equipment used or employed by the contractor and... concrete, plastering, masonry, plumbing, sheet metal work, etc. The report shall give a breakdown of...

Figurecasting Eighth Graders.

ERIC Educational Resources Information Center

Hadley, Joseph

1983-01-01

A group of eighth-grade art students created a four-panel fiberglass mural made by figurecasting in plaster. Students aided in planning and executing the mural, including acting as models. The process and problems encountered are discussed. (IS)

Refractory ceramic has wide usage, low fabrication cost

NASA Technical Reports Server (NTRS)

1964-01-01

Particulate, fused amorphous silica is formed into complex shapes by casting in plaster molds. High temperature firing is not required. This ceramic is resistant to thermal shock and exhibits good strength properties.

23. Historical American Buildings Survey L. C. Durette, Photographer July ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. Historical American Buildings Survey L. C. Durette, Photographer July 27, 1936 DETAIL OF DOVE TAILING LOGS CHIPPED TO RECEIVE INSIDE PLASTER - Gilman Garrison, Water & Clifford Streets, Exeter, Rockingham County, NH

26. Historic American Buildings Survey Albert S. Burns, Photographer September ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. Historic American Buildings Survey Albert S. Burns, Photographer September 30, 1935. FRAGMENTS OF PLASTER CEILING ROSETTE - MUSIC ROOM - The Maples, 630 South Carolina Avenue Southeast, Washington, District of Columbia, DC

[Experimental evaluation of the spraying disinfection efficiency on dental models].

PubMed

Zhang, Yi; Fu, Yuan-fei; Xu, Kan

2013-08-01

To evaluate the disinfect effect after spraying a new kind of disinfectant on the dental plaster models. The germ-free plaster samples, which were smeared with bacteria compound including Staphylococcus aureus, Escherichia coli, Saccharomyces albicans, Streptococcus mutans and Actinomyces viscosus were sprayed with disinfectants (CaviCide) and glutaraldehyde individually. In one group(5 minutes later) and another group(15 minutes later), the colonies were counted for statistical analysis after sampling, inoculating, and culturing which were used for evaluation of disinfecting efficiency. ANOVA was performed using SPSS12.0 software package. All sample bacteria were eradicated after spraying disinfectants(CaviCide) within 5 minutes and effective bacteria control was retained after 15 minutes. There was significant difference between the disinfecting efficiency of CaviCide and glutaraldehyde. The effect of disinfection with spraying disinfectants (CaviCide) on dental models is quick and effective.

Precision and accuracy of 3D lower extremity residua measurement systems

NASA Astrophysics Data System (ADS)

Commean, Paul K.; Smith, Kirk E.; Vannier, Michael W.; Hildebolt, Charles F.; Pilgram, Thomas K.

1996-04-01

Accurate and reproducible geometric measurement of lower extremity residua is required for custom prosthetic socket design. We compared spiral x-ray computed tomography (SXCT) and 3D optical surface scanning (OSS) with caliper measurements and evaluated the precision and accuracy of each system. Spiral volumetric CT scanned surface and subsurface information was used to make external and internal measurements, and finite element models (FEMs). SXCT and OSS were used to measure lower limb residuum geometry of 13 below knee (BK) adult amputees. Six markers were placed on each subject's BK residuum and corresponding plaster casts and distance measurements were taken to determine precision and accuracy for each system. Solid models were created from spiral CT scan data sets with the prosthesis in situ under different loads using p-version finite element analysis (FEA). Tissue properties of the residuum were estimated iteratively and compared with values taken from the biomechanics literature. The OSS and SXCT measurements were precise within 1% in vivo and 0.5% on plaster casts, and accuracy was within 3.5% in vivo and 1% on plaster casts compared with caliper measures. Three-dimensional optical surface and SXCT imaging systems are feasible for capturing the comprehensive 3D surface geometry of BK residua, and provide distance measurements statistically equivalent to calipers. In addition, SXCT can readily distinguish internal soft tissue and bony structure of the residuum. FEM can be applied to determine tissue material properties interactively using inverse methods.

Archaeomagnetic studies in Mesoamerica using non-conventional materials

NASA Astrophysics Data System (ADS)

Soler-Arechalde, A.; Gogichaishvili, A.; Urrutia-Fucugauchi, J.

2004-12-01

For the first time results of an archaeomagnetic study of mural paintings and unburned lime-plasters from Mesoamerica are presented. The magnetic measurements show that at least four murals (sites: Cacaxtla, Cholula and Templo Mayor) retain a remanent magnetization carried by a mixture of hematite and magnetite grains. In most specimens, a characteristic magnetization is successfully isolated by alternating field demagnetization. The mean directions are reasonably well determined for each murals and within the range of secular variation during the last centuries. Studied Mesoamerican murals apparently retain the direction of the magnetic field at the time they were painted and are therefore an invaluable source of information concerning its secular variation. Lime-plaster samples were selected from two archaeological excavation projects in the Teopancazco residential compound of Teotihuacan and the large multi-stage structure of Templo Mayor in Tenochtitlan, where chronological information is available. The intensity of remanent magnetization and low-field susceptibility are weak reflecting low relative content of magnetic minerals. NRM directions are well grouped and alternating field demagnetization shows single or two-component magnetizations. Rock-magnetic experiments point to fine-grained titanomagnetites with pseudo-single domain behavior. Anisotropy of magnetic susceptibility measurements document a depositional fabric, with normal to free-surface minimum AMS axes. Characteristic mean site directions were correlated to the paleosecular variation curve for Mesoamerica. Our results suggest that archaeomagnetic dating can be applied to mural paintings and lime-plasters, which are materials widely employed in Mesoamerica.

Consolidation of archaeological gypsum plaster by bacterial biomineralization of calcium carbonate.

PubMed

Jroundi, Fadwa; Gonzalez-Muñoz, Maria Teresa; Garcia-Bueno, Ana; Rodriguez-Navarro, Carlos

2014-09-01

Gypsum plasterworks and decorative surfaces are easily degraded, especially when exposed to humidity, and thus they require protection and/or consolidation. However, the conservation of historical gypsum-based structural and decorative materials by conventional organic and inorganic consolidants shows limited efficacy. Here, a new method based on the bioconsolidation capacity of carbonatogenic bacteria inhabiting the material was assayed on historical gypsum plasters and compared with conventional consolidation treatments (ethyl silicate; methylacrylate-ethylmethacrylate copolymer and polyvinyl butyral). Conventional products do not reach in-depth consolidation, typically forming a thin impervious surface layer which blocks pores. In contrast, the bacterial treatment produces vaterite (CaCO3) biocement, which does not block pores and produces a good level of consolidation, both at the surface and in-depth, as shown by drilling resistance measurement system analyses. Transmission electron microscopy analyses show that bacterial vaterite cement formed via oriented aggregation of CaCO3 nanoparticles (∼20nm in size), resulting in mesocrystals which incorporate bacterial biopolymers. Such a biocomposite has superior mechanical properties, thus explaining the fact that drilling resistance of bioconsolidated gypsum plasters is within the range of inorganic calcite materials of equivalent porosity, despite the fact that the bacterial vaterite cement accounts for only a 0.02 solid volume fraction. Bacterial bioconsolidation is proposed for the effective consolidation of this type of material. The potential applications of bacterial calcium carbonate consolidation of gypsum biomaterials used as bone graft substitutes are discussed. Copyright © 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Evaluation of cast creep occurring during simulated clubfoot correction

PubMed Central

Cohen, Tamara L; Altiok, Haluk; Wang, Mei; McGrady, Linda M; Krzak, Joseph; Graf, Adam; Tarima, Sergey; Smith, Peter A; Harris, Gerald, F

2016-01-01

The Ponseti method is a widely accepted and highly successful conservative treatment of pediatric clubfoot involving weekly manipulations and cast applications. Qualitative assessments have indicated the potential success of the technique with cast materials other than standard plaster of Paris. However, guidelines for clubfoot correction based on the mechanical response of these materials have yet to be investigated. The current study sought to characterize and compare the ability of three standard cast materials to maintain the Ponseti corrected foot position by evaluating cast creep response. A dynamic cast testing device, built to model clubfoot correction, was wrapped in plaster-of-Paris, semi-rigid fiberglass, and rigid fiberglass. Three-dimensional motion responses to two joint stiffnesses were recorded. Rotational creep displacement and linearity of the limb-cast composite were analyzed. Minimal change in position over time was found for all materials. Among cast materials, the rotational creep displacement was significantly different (p < 0.0001). The most creep displacement occurred in the plaster-of-Paris (2.0 degrees), then the semi-rigid fiberglass (1.0 degrees), and then the rigid fiberglass (0.4 degrees). Torque magnitude did not affect creep displacement response. Analysis of normalized rotation showed quasi—linear viscoelastic behavior. This study provided a mechanical evaluation of cast material performance as used for clubfoot correction. Creep displacement dependence on cast material and insensitivity to torque were discovered. This information may provide a quantitative and mechanical basis for future innovations for clubfoot care. PMID:23636764

Adjustable hinge permits movement of knee in plaster cast

NASA Technical Reports Server (NTRS)

Maley, W. E.

1967-01-01

Metal knee hinge with an adjustable sleeve worn on the outside of a leg cast facilitates movement of the knee joint. This helps eliminate stiffness of the knee and eliminates bulkiness and adjustment difficulty.

Frescoes: An Endangered Species.

ERIC Educational Resources Information Center

Sheniak, David

1984-01-01

While it is impossible to produce a true fresco in the classroom, a number of projects approximate the look, feel, and technique of fresco painting. Students can create their own frescoes, using plaster of paris and watercolors. (RM)

22. TYPICAL FOR THE FIRST FLOOR INTERIORS, ARE PAIRED COLUMN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. TYPICAL FOR THE FIRST FLOOR INTERIORS, ARE PAIRED COLUMN PILASTERS IN KEENE CEMENT PLASTER. BASE OF PILASTER IS SHOWN. - Pacific Telephone & Telegraph Company Building, 1519 Franklin Street, Oakland, Alameda County, CA

Detail view from the east of the west door in ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail view from the east of the west door in the Grand Banqueting Hall. Note plaster turkey ornament in the door pediment. - Masonic Temple, 1 North Broad Street, Philadelphia, Philadelphia County, PA

24. Historical American Buildings Survey L. C. Durette, Photographer July ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. Historical American Buildings Survey L. C. Durette, Photographer July 27, 1936 INTERIOR OF GARRISON NORTH CORNER 2nd FLOOR LOGS CHIPPED TO RECEIVE INSIDE PLASTER - Gilman Garrison, Water & Clifford Streets, Exeter, Rockingham County, NH

22. Historical American Buildings Survey L. C. Durette, Photographer July ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. Historical American Buildings Survey L. C. Durette, Photographer July 27, 1936 NORTH CORNER OF GARRISON 2nd STORY SHOWING LOGS CHIPPED TO RECEIVE INSIDE PLASTER - Gilman Garrison, Water & Clifford Streets, Exeter, Rockingham County, NH

Longitudinal changes in blood lead level in children and their relationship to season, age, and exposure to paint or plaster.

PubMed Central

McCusker, J

1979-01-01

Children screened for lead poisoning in the Brownsville district of New York City in either summer or winter were followed with blood lead tests for approximately six months to one year from screening to measure longitudinal changes in blood lead level and to identify some determinants of the changes. Only minimal evidence was found of the hypothesized summer rise in blood lead level, while the predominant trend seemed to be for blood lead levels to display statistical regression to the mean. In children found to have low to intermediate blood lead levels (less than 55 microgram/100ml) at screening, variables which were found to predict a rise in blood lead level of 10 microgram/100ml or greater from winter to summer were under age three and/or exposure to paint or plaster. PMID:426160

Haematoma block in reduction of distal radial fractures.

PubMed

Ogunlade, S O; Omololu, A B; Alonge, T O; Salawu, S A; Bamgboye, E A

2002-01-01

A total of 35 patients who presented in the Accident and Emergency Department of University College Hospital with displaced distal radial fracture between January 2000 and March 2001 had reduction of the fracture under haematoma block using 10ml of 2% lignocaine. There was significant reduction of the pain following infiltration of the fracture site with lignocaine and significant pain reduction during manipulation compared to pain score at presentation. All the patients had satisfactory reduction of the fracture. The fracture was mobilised in Plaster of Paris 6 weeks in patients with Collens' fracture and 3 weeks in patients with distal radial epiphyseal injury. All patients had good range of movement at 8 weeks after removal of Plaster of Paris and patients expressed satisfaction with this method. We recommend the use of Haematoma block for patients of 15 years and above with displaced distal radial fracture in the Accident and Emergency Department.

Towards evidence-based emergency medicine: best BETs from the Manchester Royal Infirmary. BET 2: Immobilisation of stable ankle fractures: plaster cast or functional brace?

PubMed

Thackray, Anna J; Taylor, Jonathan

2013-06-01

A short-cut review of the literature was carried out to establish whether a functional brace was as good as a traditional plaster of Paris to immobilise a stable ankle fracture in terms of functionality and recovery speed. A total of 260 papers was found using the below outlined search method, of which five were thought to represent the best evidence to answer the specific clinical question. The author, date and country of publication, patient group studied, study type, relevant outcomes, results and study weaknesses of these are shown in table 2. The clinical bottom line is that the limited evidence seems to suggest that a functional brace appears to give more favourable outcomes. Good quality studies involving large populations are, however, needed to delineate a clear answer to this specific question.

Peculiarities of the processes of hydration of binding substances in the arbolite mixture

NASA Astrophysics Data System (ADS)

Innokentieva, L. S.; Egorova, A. D.; Emelianova, Z. V.

2017-09-01

Cement and sand solution is traditionally used for production of wood concrete. But it is known that impact of water-soluble substances of wood on the hardening cement is shown in the stabilizing effect. The "Cement poisons" consisting generally of the HOCH carbohydrate groups, sedimented on a surface of particles of minerals of cement 3CaO.SiO2 (three-calcic silicate) and 3CaO.Al2O3 (three-calcic aluminate) form the thinnest covers which complicate the course of processes of hydration of cement. Plaster in comparison with cement is less sensitive to extractive substances of wood therefore their combination to wood (including waste of logging and a woodworking) both coniferous and deciduous species is allowed. Composite plaster binding with hongurin as active mineral additive agent are applied at selection of composition of arbolite, at the same time dependences of their physicomechanical properties on characteristics of filler are received.

Correlation and agreement of a digital and conventional method to measure arch parameters.

PubMed

Nawi, Nes; Mohamed, Alizae Marny; Marizan Nor, Murshida; Ashar, Nor Atika

2018-01-01

The aim of the present study was to determine the overall reliability and validity of arch parameters measured digitally compared to conventional measurement. A sample of 111 plaster study models of Down syndrome (DS) patients were digitized using a blue light three-dimensional (3D) scanner. Digital and manual measurements of defined parameters were performed using Geomagic analysis software (Geomagic Studio 2014 software, 3D Systems, Rock Hill, SC, USA) on digital models and with a digital calliper (Tuten, Germany) on plaster study models. Both measurements were repeated twice to validate the intraexaminer reliability based on intraclass correlation coefficients (ICCs) using the independent t test and Pearson's correlation, respectively. The Bland-Altman method of analysis was used to evaluate the agreement of the measurement between the digital and plaster models. No statistically significant differences (p > 0.05) were found between the manual and digital methods when measuring the arch width, arch length, and space analysis. In addition, all parameters showed a significant correlation coefficient (r ≥ 0.972; p < 0.01) between all digital and manual measurements. Furthermore, a positive agreement between digital and manual measurements of the arch width (90-96%), arch length and space analysis (95-99%) were also distinguished using the Bland-Altman method. These results demonstrate that 3D blue light scanning and measurement software are able to precisely produce 3D digital model and measure arch width, arch length, and space analysis. The 3D digital model is valid to be used in various clinical applications.

Corticosteroid transdermal delivery to target swelling, edema and inflammation following facial rejuvenation procedures

PubMed Central

Iannitti, T; Rottigni, V; Palmieri, B

2013-01-01

Background and aim The use of transdermal therapeutic systems has spread worldwide since they allow effective local drug delivery. In the present study, we investigated the efficacy and safety of a new betamethasone valerate medicated plaster (Betesil®) to manage facial swelling, edema, inflammation, ecchymosis, and hematoma, when applied immediately after a facial rejuvenation procedure. Materials and methods We applied the plaster to the skin of 20 healthy patients for 12 hours immediately after hyaluronic acid-based procedure performed with the aim of erasing facial wrinkles of perioral and nasolabial folds and improving chin and eye contour. A further 20 patients underwent the same cosmetic procedure, but they were treated with an aescin 10% cream (applied immediately after the procedure, in the evening, and the morning after) and served as control group. Results Betesil® application resulted in a significant improvement in swelling/edema/inflammation score, if compared with aescin 10% cream (P < 0.01). As for facial ecchymosis and hematoma around the needle injection track, only two patients in the active treatment group displayed minimal ecchymosis and hematoma. In the control group, two patients presented minimal ecchymosis and three slight hematoma. However, using the ecchymosis/hematoma score, no significant difference between Betesil® and aescin 10% cream groups was observed. Patients’ satisfaction was significantly higher among subjects receiving Betesil®, if compared to patients receiving aescin 10% cream (P < 0.01). Conclusion The present study supports the use of Betesil® plaster immediately after facial cosmetic procedures in order to safely control swelling, edema, and inflammation. PMID:24101860

Biocompatibility and biodegradation studies of PCL/β-TCP bone tissue scaffold fabricated by structural porogen method.

PubMed

Lu, Lin; Zhang, Qingwei; Wootton, David; Chiou, Richard; Li, Dichen; Lu, Bingheng; Lelkes, Peter; Zhou, Jack

2012-09-01

Three-dimensional printer (3DP) (Z-Corp) is a solid freeform fabrication system capable of generating sub-millimeter physical features required for tissue engineering scaffolds. By using plaster composite materials, 3DP can fabricate a universal porogen which can be injected with a wide range of high melting temperature biomaterials. Here we report results toward the manufacture of either pure polycaprolactone (PCL) or homogeneous composites of 90/10 or 80/20 (w/w) PCL/beta-tricalcium phosphate (β-TCP) by injection molding into plaster composite porogens fabricated by 3DP. The resolution of printed plaster porogens and produced scaffolds was studied by scanning electron microscopy. Cytotoxicity test on scaffold extracts and biocompatibility test on the scaffolds as a matrix supporting murine osteoblast (7F2) and endothelial hybridoma (EAhy 926) cells growth for up to 4 days showed that the porogens removal process had only negligible effects on cell proliferation. The biodegradation tests of pure PCL and PCL/β-TCP composites were performed in DMEM with 10 % (v/v) FBS for up to 6 weeks. The PCL/β-TCP composites show faster degradation rate than that of pure PCL due to the addition of β-TCP, and the strength of 80/20 PCL/β-TCP composite is still suitable for human cancellous bone healing support after 6 weeks degradation. Combining precisely controlled porogen fabrication structure, good biocompatibility, and suitable mechanical properties after biodegradation, PCL/β-TCP scaffolds fabricated by 3DP porogen method provide essential capability for bone tissue engineering.

Wall paintings studied using Raman spectroscopy: a comparative study between various assays of cross sections and external layers.

PubMed

Perez-Rodriguez, Jose Luis; Robador, Maria Dolores; Centeno, Miguel Angel; Siguenza, Belinda; Duran, Adrian

2014-01-01

This work describes a comparative study between in situ applications of portable Raman spectroscopy and direct laboratory measurements using micro-Raman spectroscopy on the surface of small samples and of cross sections. The study was performed using wall paintings from different sites of the Alcazar of Seville. Little information was obtained using a portable Raman spectrometer due to the presence of an acrylic polymer, calcium oxalate, calcite and gypsum that was formed or deposited on the surface. The pigments responsible for different colours, except cinnabar, were not detected by the micro-Raman spectroscopy study of the surface of small samples taken from the wall paintings due to the presence of surface contaminants. The pigments and plaster were characterised using cross sections. The black colour consisted of carbon black. The red layers were formed by cinnabar and white lead or by iron oxides. The green and white colours were composed of green emerald or atacamite and calcite, respectively. Pb3O4 has also been characterised. The white layers (plaster) located under the colour layers consisted of calcite, quartz and feldspars. The fresco technique was used to create the wall paintings. A wall painting located on a gypsum layer was also studied. The Naples yellow in this wall painting was not characterised due to the presence of glue and oils. This study showed the advantage of studying cross sections to completely characterise the pigments and plaster in the studied wall paintings. Copyright © 2013 Elsevier B.V. All rights reserved.

Vandalism: Take Tempting Targets Out of Washrooms

ERIC Educational Resources Information Center

Nation's Schools, 1973

1973-01-01

Provides practical suggestions from school plant managers who have succeeded in cutting down on washroom vandalism. In addition to doorless stalls, recessed accessories, and limiting space, the article suggests concealed piping, plaster ceilings, and removal of all target items. (EA)

John Rogers: "Checkers Up at the Farm."

ERIC Educational Resources Information Center

Zeller, Terry

1987-01-01

Based on John Rogers' 1887 painted plaster sculpture called "Checkers Up at the Farm," this lesson seeks to introduce primary-level students to the idea of sculpture in the round and how sculpture can communicate ideas, emotions, and values. (JDH)

25. MAIN MEETING ROOM STAIRWAY IN SOUTHEAST CORNER. Stairway seen ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. MAIN MEETING ROOM STAIRWAY IN SOUTHEAST CORNER. Stairway seen from below showing lath and plaster fireproofing applied to framing before treads and risers. - Twelfth Street Meeting House, 20 South Twelfth Street, Philadelphia, Philadelphia County, PA

Hazardous Waste Cleanup: American Standard Incorporated in Hamilton Township, New Jersey

EPA Pesticide Factsheets

American Standard Incorporated is located at 240 Princeton Avenue in Trenton, New Jersey. American Standard's Trenton Pottery Facility has operated at its present location since 1923. The facility manufactures ceramic plumbing fixtures using clay, plaster

29. RECYCLED ATTIC JOISTS SHOWING SHINGLE LATH NOTCHING ON TOP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. RECYCLED ATTIC JOISTS SHOWING SHINGLE LATH NOTCHING ON TOP SURFACE (Note shadow of plaster lath on bottom surface. See also PA-1440-28.) - James McCrea Houses, 108-110 Sansom Street, Philadelphia, Philadelphia County, PA

7 Ways.

ERIC Educational Resources Information Center

Corrigan, Nancy P.; And Others

1982-01-01

Describes seven art activities for elementary and secondary classes. Activities include making Pueblo Indian-style pottery, casting stained glass designs in plaster, constructing cloth gnome-dolls, making ceramic reliefs of Victorian house facades and dream cars, drawing South American folk art objects, and sewing wearable art. (AM)

14. Photocopy of pre1956 photograph. Original in library of John ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. Photocopy of pre-1956 photograph. Original in library of John S. Lehmann Building, Missouri Botanical Garden. CEILING, SHOWING ORIGINAL SKYLIGHT NOW PLASTERED OVER - Missouri Botanical Garden, Museum, 2345 Tower Grove Avenue, Saint Louis, Independent City, MO

55. Interior view, porch chamber from the south (Note the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

55. Interior view, porch chamber from the south (Note the ionic capital volute visible through the plaster to the upper right of the bed). - John Bartram House & Garden, House, 54th Street & Lindbergh Boulevard, Philadelphia, Philadelphia County, PA

32. Interior view, encased fireplace and remains of the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

32. Interior view, encased - fireplace and remains of the hearth against the north wall, with scale l(note: hole punched through plaster allows access to the flues) - Kiskiack, Naval Mine Depot, State Route 238 vicinity, Yorktown, York County, VA

Detail view from the east of the west door in ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail view from the east of the west door in the Grand Banqueting Hall. Note scale laid against the right pilaster and plaster turkey ornament in the door pediment. - Masonic Temple, 1 North Broad Street, Philadelphia, Philadelphia County, PA

Bribes and plasters won't do.

PubMed

Coram, Michael

2017-08-23

I disagree with Graham Scott's editorial (9 August). We should not be bribing men into nursing, we should be fighting to reinstate the bursary for all healthcare students and be looking at the issues around gender stereotyping and perceptions relating to occupations.

Methodological questions of creating tissue-equivalent phantoms

NASA Technical Reports Server (NTRS)

Kolodkin, A. V.; Popov, V. I.; Sychkov, M. A.; Nikl, I.; Erdei, M.; Eyben, O.

1974-01-01

On the basis of analysis and generalization of literature data, the composition of tissue equivalent plastic was justified, parameters of a standard man were determined, plaster and metal forms were created for casting dummies, and an experimental model was produced from tissue equivalent material.

Uncle Sam Flunks Asbestos Control in Schools.

ERIC Educational Resources Information Center

Gough, Michael

1988-01-01

Discusses the problem of using asbestos to insulate heating and air-conditioning systems in schools and mixing asbestos into ceiling plaster for fireproofing and noise control. Suggests that the Environmental Protection Agency's plan for asbestos removal may be causing problems where none exist. (TW)

Learning about Fossil Formation by Classroom Simulation.

ERIC Educational Resources Information Center

Schlenker, Richard M.; Yoshida, Sarah J.

1991-01-01

Activities in which students build their own simulations of fossils, using seashells, chicken bones, toy dinosaurs, or leaves as models and plaster of paris, sand, mud, clay, or a mixture of gravel and clay as a matrix are presented. Curriculum extensions are included. (KR)

Relevance--East New York Style

ERIC Educational Resources Information Center

Lipschitz, Beverly

1970-01-01

Slum environments produce lead poisoning which counselors in East New York sought to bring to attention of parents and legislators by a screening program to identify children who had it. Counselors also established a program to alert parents to dangers of ingesting fallen plaster. (CJ)

Interior building details of Building B, Room B001: fouroverfour wood ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior building details of Building B, Room B-001: four-over-four wood painted wood with brick sill and painted plaster west brick wall; westerly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

Cheaper Custom Shielding Cups For Arc Welding

NASA Technical Reports Server (NTRS)

Morgan, Gene E.

1992-01-01

New way of making special-purpose shielding cups for gas/tungsten arc welding from hobby ceramic greatly reduces cost. Pattern machined in plastic. Plaster-of-paris mold made, and liquid ceramic poured into mold. Cost 90 percent less than cup machined from lava rock.

Interior building details of Building A, dungeon cell adjacent to ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior building details of Building A, dungeon cell adjacent to northwest cell: granite and brick threshold, poured concrete floors, plastered finished walls, vaulted veiling; northwesterly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

[Manipulative reduction and plaster external fixation for the treatment of the scaphoid fracture and perilunate dislocation].

PubMed

Zhang, Xin; Wei, Qiang; Ji, Fang; Tong, Da-Ke; Tang, Hao; Zhang, Hao; Yu, Jin-Guo; Yang, Ji-Dong; Cui, Rui; Huo, Ning-Ning

2018-05-25

To investigate the efficacy and complications of manual reduction and external fixation for the treatment of scaphoid fractures and perilunate dislocations. From January 2009 to January 2013, 43 patients suffered from scaphoid fractures and perilunate dislocations were retrospective analyzed. Among them, 17 cases were treated with manipulative reduction and plaster external fixation as conservation group including 10 males and 7 females, the other 26 cases were treated with application of surgical as operation group including 15 males and 11 females. The clinical effects were assessed by Cooney function score, radiological analysis and observation of complications. All patients were followed up for(45.00±8.72) months ranging from 36 to 60 months. At the final follow-up, the Cooney score of wrist function was 88.53±4.24 in conservation group and 89.58±4.59in operation group( t= 0.455, P >0.05). During the follow-up, 4 patients were found scaphoid avascular necrosis in the imaging performance in the conservation group(χ²=4.32, P <0.05). The difference of other complications between two groups was not statistically significant( P >0.05). For patients suffered from the scaphoid fractures and perilunate dislocation, the early manipulative reduction and plaster external fixation after injury as soon as possible is necessary. Maintaining a satisfactory reduction and reliable fixation at the same time can lead to good treatment effect and there's no weakness compared to surgical treatment. But there was an increase in danger of complications. The key of conservative treatment lies in early diagnosis and maintenance of reduction, reliable fixation, and timely and appropriate functional exercise. Copyright© 2018 by the China Journal of Orthopaedics and Traumatology Press.

The University Münster Model Surgery System for Orthognathic Surgery. Part II -- KD-MMS.

PubMed

Ehmer, Ulrike; Joos, Ulrich; Ziebura, Thomas; Flieger, Stefanie; Wiechmann, Dirk

2013-01-04

Model surgery is an integral part of the planning procedure in orthognathic surgery. Most concepts comprise cutting the dental cast off its socket. The standardized spacer plates of the KD-MMS provide for a non-destructive, reversible and reproducible means of maxillary and/or mandibular plaster cast separation. In the course of development of the system various articulator types were evaluated with regard to their capability to provide a means of realizing the concepts comprised of the KD-MMS. Special attention was dedicated to the ability to perform three-dimensional displacements without cutting of plaster casts. Various utilities were developed to facilitate maxillary displacement in accordance to the planning. Objectives of this development comprised the ability to implement the values established in the course of two-dimensional ceph planning. The system - KD-MMS comprises a set of hardware components as well as a defined procedure. Essential hardware components are red spacer and blue mounting plates. The blue mounting plates replace the standard yellow SAM mounting elements. The red spacers provide for a defined leeway of 8 mm for three-dimensional movements. The non-destructive approach of the KD-MMS makes it possible to conduct different model surgeries with the same plaster casts as well as to restore the initial, pre-surgical situation at any time. Thereby, surgical protocol generation and gnathologic splint construction are facilitated. The KD-MMS hardware components in conjunction with the defined procedures are capable of increasing efficiency and accuracy of model surgery and splint construction. In cases where different surgical approaches need to be evaluated in the course of model surgery, a significant reduction of chair time may be achieved.

A cheap protocol for colour measure and for diagnostic in planning a cultural heritage restoration. Case study: main façade of Palazzo Governi (Cagliari, Sardinia, Italy).

PubMed

Sammartino, M P; Genova, C; Ronca, S; Cau, G; Visco, G

2017-06-01

Due to the bad state of conservation, "Palazzo Governi", a seventeenth-century building located in the old town district of "Stampace" in Cagliari (Sardinia, Italy), was subjected to restoration. Thus, according to the Italian Law n. 1089, the main façade colour must be reproduced, and therefore, its identification was required. The available samples looked fairly degraded, in particular as an easy plaster to crumble; so, some other analyses able to identify the degradation cause were performed. Two different approaches were adopted to attain the first goal, the visual colour assessment by a sensory panel (subjective) and the instrumental measurement by colorimetry (objective). Ion chromatography and inductively coupled plasma-optical emission spectroscopy analyses, as well as conductivity and pH measurements, were performed to evaluate the presence of water-soluble salts inside the plaster, as possible cause of degradation; the binder/aggregate ratio was also evaluated. A full mineralogical and petrographic characterisation of the materials constituting the samples, as well as the identification of their stratigraphy and some other morphologic and structural features suitable to highlight eventual forms of degradation, were performed by optical microscopy. Scanning electron microscopy coupled to X-ray microanalysis was been also used in order to confirm and/or to integrate data obtained by optical microscopy. The samples have been compared with two samples coming from two other buildings, also located in Sardinia, that looked in good conservation state. The results evidenced that the causes of degradation come from a high salt (especially sulphate) content and a scarce presence of binder in the plaster that can be imputed to a wrong initial composition and/ or to a leaching by acidic rain.

Monitoring the performance of innovative and traditional biocides mixed with consolidants and water-repellents for the prevention of biological growth on stone.

PubMed

Pinna, Daniela; Salvadori, Barbara; Galeotti, Monica

2012-04-15

In this study, some mixtures of consolidants or water-repellent products and biocides developed to prevent biological growth, were tested over time on three stone substrates with different bioreceptivity. The performance of both traditional (tetraethylorthosilicate, methylethoxy polysiloxane, Paraloid B72, tributyltin oxide, dibutyltin dilaurate) and innovative compounds (copper nanoparticles) was assessed using colour measurements, the water absorption by contact sponge method, and observation under stereo and optical microscopes. The application of the mixtures had also the purpose of controlling re-colonization on stone after a conservation treatment. The study site was the archaeological Area of Fiesole; the mixtures were applied in situ to sandstone, marble and plaster which had been cleaned beforehand. An innovative aspect of the study is that, by using non-invasive methods, it also permitted monitoring the mixtures' effectiveness in preventing biological growth. The monitoring results made it possible to assess the bioreceptivity of the treated stones (sandstone, marble, plaster) over a period of almost three years. The results showed that the mixtures of consolidants or water-repellent products with biocides were effective in preventing biological growth on both a substrate with low bioreceptivity like plaster and a substrate with high bioreceptivity such as marble. The innovative mixture of nano-Cu particles with a water-repellent yielded good results in terms of preventing biological colonization. Moreover, they apparently did not affect the substrates' colour. Mixtures of nano-Cu particles with a consolidant and a water-repellent hold great promise for preventing re-colonization of stone after conservation treatment. Copyright © 2012 Elsevier B.V. All rights reserved.

Correction of Pectus Excavatum by Custom-Made Silicone Implants: Contribution of Computer-Aided Design Reconstruction. A 20-Year Experience and 401 Cases.

PubMed

Chavoin, Jean-Pierre; Grolleau, Jean-Louis; Moreno, Benjamin; Brunello, Jérémie; André, Aymeric; Dahan, Marcel; Garrido, Ignacio; Chaput, Benoit

2016-05-01

In the absence of demonstrable functional impairment, pectus excavatum is merely a congenital deformity, albeit with a marked psychological impact. Many patients do not wish to undergo thoracic remodeling operations, which are invasive and do not clearly result in respiratory or cardiac improvement. From 1993 to 2015, the authors designed 401 custom-made silicone implants to treat funnel chests. Before 2007, implants were made from plaster chest molds. Beginning in 2007, three-dimensional reconstructions were made from computed tomographic scans by computer-aided design. The authors prospectively recorded all assessments and follow-up data since 1993. Preoperative and postoperative photographs of two random groups of 50 patients were analyzed, in a blinded manner, by two surgeons independently. Intraoperative and postoperative complications, clinical outcomes, patient satisfaction, and quality of life were evaluated. One infection and three hematomas were recorded. Periprosthetic seroma was evident in all cases. Patients rated the cosmetic outcomes of computer-aided design implants significantly higher than those of the earlier implants made using plaster molds (p = 0.030). Malformations were better corrected in the computer-aided design group (86 percent) than in the plaster group (72 percent) (p = 0.038). Patient satisfaction was higher in the former group (p = 0.011). Medical Outcomes Study 36-Item Short-Form Health Survey scores revealed significant improvements, both socially and emotionally. Correction of pectus excavatum using a computer-aided design silicone implant fulfils aesthetic and psychological demands. The technique is simple and reliable and yields high-quality results. In the medium term, the approach may render invasive techniques obsolete. These operations remain risky and of doubtful functional utility. Therapeutic, III.

Accuracy of a three-dimensional dentition model digitized from an interocclusal record using a non-contact surface scanner.

PubMed

Kihara, Takuya; Yoshimi, Yuki; Taji, Tsuyoshi; Murayama, Takeshi; Tanimoto, Kotaro; Nikawa, Hiroki

2016-08-01

For orthodontic treatment, it is important to assess the dental morphology, as well as the position and inclination of teeth. The aim of this article was to develop an efficient and accurate method for the three-dimensional (3D) imaging of the maxillary and mandibular dental morphology by measuring interocclusal records using an optical scanner. The occlusal and incisal morphology of participants was registered in the intercuspal position using a hydrophilic vinyl polysiloxane and digitized into 3D models using an optical scanner. Impressions were made of the maxilla and mandible in alginate materials in order to fabricate plaster models and created into 3D models using the optical scanner based on the principal triangulation method. The occlusal and incisal areas of the interocclusal records were retained. The buccal and lingual areas were added to these regions entirely by the 3D model of the plaster model. The accuracy of this method was evaluated for each tooth, with the dental cast 3D models used as controls. The 3D model created from the interocclusal record and the plaster model of the dental morphology was analysed in 3D software. The difference between the controls and the 3D models digitized from the interocclusal records was 0.068±0.048mm, demonstrating the accuracy of this method. The presence of severe crowding may compromise the ability to separate each tooth and digitize the dental morphology. The digitization method in this study provides sufficient accuracy to visualize the dental morphology, as well as the position and inclination of these teeth. © The Author 2015. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Comparison of Risk of Carpal Tunnel Syndrome in Patients with Distal Radius Fractures After 7 Treatments

PubMed Central

Zhao, Huan-Li; Wang, Gui-Bin; Jia, Yue-Qing; Zhu, Shi-Cai; Zhang, Feng-Fang; Liu, Hong-Mei

2015-01-01

Background To compare risk of carpal tunnel syndrome (CTS) in distal radius fracture (DRF) patients after 7 treatments using bridging external fixation (BrEF), non-bridging external fixation (non-BrEF), plaster fixation, K-wire fixation, dorsal plating fixation, volar plating fixation, and dorsal and volar plating by performing a network meta-analysis. Material/Methods An exhaustive search of electronic databases identified randomized controlled trails (RCTs) closely related to our study topic. The published articles were screened, based on predefined inclusion and exclusion criteria, to select high-quality studies for the present network meta-analysis. Data extracted from the selected studies were analyzed using STATA version 12.0 software. Results The literature search and selection process identified 12 eligible RCTs that contained a total of 1370 DRF patients (394 patients with BrEF, 377 patients with non-BrEF, 89 patients with K-wire fixation, 192 patients with plaster fixation, 42 patients with dorsal plating fixation, 152 patients with volar plating fixation, and 124 patients with dorsal and volar plating fixation). Our network meta-analysis results demonstrated no significant differences in CTS risk among the 7 treatments (P>0.05). The value of surface under the cumulative ranking curve (SUCRA), however, suggested that dorsal plating fixation is the optimal treatment, with the lowest risk of CTS in DRF patients (dorsal plating fixation: 89.2%; dorsal and volar plating: 57.8%; plaster fixation: 50.9%; non-BrEF: 50.6%; volar plating fixation: 39.6%; BrEF: 38.4%; K-wire fixation: 23.6%). Conclusions Our network meta-analysis provides evidence that dorsal plating fixation significantly decreases the risk of CTS and could be the method of choice in DRF patients. PMID:26391617

Antibiotic-loaded plaster of Paris implants coated with poly lactide-co-glycolide as a controlled release delivery system for the treatment of bone infections.

PubMed

Benoit, M A; Mousset, B; Delloye, C; Bouillet, R; Gillard, J

1997-01-01

Plaster of Paris implants containing vancomycin (60 mg/g of carrier) were prepared in order to be used as local delivery system for the treatment of bone infections. The regulation of the release rate was performed by coating the carrier with a polylactide-co-glycolide polymer composed by 10% (w/w) polyglycolic acid and 90% (w/w) racemic poly (D,L-lactic acid). The release of the antibiotic from the biodegradable matrix was evaluated in vitro. From this investigation, it is clear that the drug elution depends on the coating depth. After a burst effect occurring on the first day of the experiment, therapeutic concentrations were measured during one week when uncoated implants were used. The coating allowed decrease of the burst effect and extended efficient release to more than five weeks when the implants were embedded with six layers (162 microns) of PLA45GA10. This delivery system was implanted into the femoral condyle of rabbits. It was shown that the in vivo release was also closely regulated by the coating depth. In all bone tissues (bone marrow and cortical bone) surrounding the pellets, the drug concentration exceeded the Minimum Inhibitory Concentration for the common causative organisms of bone infections (Staphylococcus aureus) for at least four weeks without inducing serum toxic levels. Due to its cheapness, facility of use and sterilization, biocompatibility and biodegradability, plaster of Paris coated with PLA45GA10 polymer giving a controlled release of vancomycin appears to be a promising sustained release delivery system of antibiotics for the treatment of bone and joint infections.

Single tooth torque correction in the lower frontal area by a completely customized lingual appliance.

PubMed

Jacobs, Collin; Katzorke, Milena; Wiechmann, Dirk; Wehrbein, Heiner; Schwestka-Polly, Rainer

2017-10-10

Aim of this study was to analyze the efficacy and precision of the completely customized lingual appliance (CCLA) regarding the single tooth torque correction. The study also examined external apical root resorptions as possible side effects of torque correction and the changings of the periodontal situation. A case series of three patients were included. The patients showed a single tooth torque problem with a gingival recession and were treated with the CCLA. Plaster casts before and after treatment and plaster casts of the set up were scanned and superimposed. Deviations between the two plaster casts were analyzed at different points of interest. Changes of the gingival recession were compared before and after treatment. Relative root resorptions were measured by the orthopantomograms. Treatment times were assessed by the records of the patients. Results were presented descriptively. The mean change of the most apical part of the root reached by the orthodontic treatment was 1.8 ± 0.3 mm. The largest deviation between set up and final model was measured on the occlusal surface of the tooth 36 with 0.8 mm. Most measurement points showed a deviation of 0.5 mm or less. The depths of the gingival recession showed a significant reduction of 4.7 mm. The widths of the gingival recession were reduced by 1.1 mm. The average relative root resorption of the corrected teeth was 2.7 ± 1.5%. The average treatment time was 13.8 ± 4.5 months. This is the first study showing that the CCLA with its high precision is very effective in correcting single tooth torque problems. Orthodontic torque correction resulted in a significant reduction of gingival recessions and caused only negligible root resorptions.

Do You Have Work-Related Asthma? A Guide for You and Your Doctor

MedlinePlus

... Polyurethane foam • Paints, lacquers, ink, varnishes, sealants, finishes • Insulation materials • Polyurethane rubber • Glues and adhesives • Car manufacture and repair • Building construction (plaster, insulation) • Foam blowing and cutting • Painting • Truck bed liner ...

Paper Casting.

ERIC Educational Resources Information Center

Arrasjid, Dorine A.

1980-01-01

Describes an art project, based on the work of artist Chew Teng Beng, in the molding of wet paper on a plaster cast to create embossed paper designs. The values of such a project are outlined, including a note that its tactile approach makes it suitable to visually handicapped students. (SJL)

49 CFR 1039.11 - Miscellaneous commodities exemptions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... or lime plaster. 32 95 Nonmetallic earths or minerals, ground or treated in any other manner except..., or old worn-out block tin pipe having value for remelting purposes only. 40221 ......do. Textile... fertilizer. 4029176 ......do. Automobile shredder residue. 4111434 ......do. Bags, old, burlap, gunny, istle...

49 CFR 1039.11 - Miscellaneous commodities exemptions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... or lime plaster. 32 95 Nonmetallic earths or minerals, ground or treated in any other manner except..., or old worn-out block tin pipe having value for remelting purposes only. 40221 ......do. Textile... fertilizer. 4029176 ......do. Automobile shredder residue. 4111434 ......do. Bags, old, burlap, gunny, istle...

49 CFR 1039.11 - Miscellaneous commodities exemptions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... or lime plaster. 32 95 Nonmetallic earths or minerals, ground or treated in any other manner except..., or old worn-out block tin pipe having value for remelting purposes only. 40221 ......do. Textile... fertilizer. 4029176 ......do. Automobile shredder residue. 4111434 ......do. Bags, old, burlap, gunny, istle...

INTERIOR DETAIL, SECONDSTORY JOISTS, SUBFLOORING, AND FIREPLACE HEARTH RELIEVING ARCH. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR DETAIL, SECOND-STORY JOISTS, SUBFLOORING, AND FIREPLACE HEARTH RELIEVING ARCH. THESE FEATURES WERE MADE VISIBLE AFTER A 2002 FAILURE OF WHAT WAS LIKELY THE ORIGINAL EIGHTEENTH-CENTURY CEILING PLASTER IN THE SOUTHWEST CABINET - The Woodlands, 4000 Woodlands Avenue, Philadelphia, Philadelphia County, PA

21 CFR 872.3150 - Articulator.

Code of Federal Regulations, 2010 CFR

2010-04-01

... DENTAL DEVICES Prosthetic Devices § 872.3150 Articulator. (a) Identification. An articulator is a mechanical device intended to simulate movements of a patient's upper and lower jaws. Plaster casts of the patient's teeth and gums are placed in the device to reproduce the occlusion (bite) and articulation of...

Kinetics of oil saponification by lead salts in ancient preparations of pharmaceutical lead plasters and painting lead mediums.

PubMed

Cotte, M; Checroun, E; Susini, J; Dumas, P; Tchoreloff, P; Besnard, M; Walter, Ph

2006-12-15

Lead soaps can be found in archaeological cosmetics as well as in oil paintings, as product of interactions of lead salts with oil. In this context, a better understanding of the formation of lead soaps allows a follow-up of the historical evolution of preparation recipes and provides new insights into conservation conditions. First, ancient recipes of both pharmaceutical lead plasters and painting lead mediums, mixtures of oil and lead salts, were reconstructed. The ester saponification by lead salts is determined by the preparation parameters which were quantified by FT-IR spectrometry. In particular, ATR/FT-IR spectrometer was calibrated by the standard addition method to quantitatively follow the kinetics of this reaction. The influence of different parameters such as temperature, presence of water and choice of lead salts was assessed: the saponification is clearly accelerated by water and heating. This analysis provides chemical explanations to the historical evolution of cosmetic and painting preparation recipes.

Light Steel-Timber Frame with Composite and Plaster Bracing Panels

PubMed Central

Scotta, Roberto; Trutalli, Davide; Fiorin, Laura; Pozza, Luca; Marchi, Luca; De Stefani, Lorenzo

2015-01-01

The proposed light-frame structure comprises steel columns for vertical loads and an innovative bracing system to efficiently resist seismic actions. This seismic force resisting system consists of a light timber frame braced with an Oriented Strand Board (OSB) sheet and an external technoprene plaster-infilled slab. Steel brackets are used as foundation and floor connections. Experimental cyclic-loading tests were conduced to study the seismic response of two shear-wall specimens. A numerical model was calibrated on experimental results and the dynamic non-linear behavior of a case-study building was assessed. Numerical results were then used to estimate the proper behavior factor value, according to European seismic codes. Obtained results demonstrate that this innovative system is suitable for the use in seismic-prone areas thanks to the high ductility and dissipative capacity achieved by the bracing system. This favorable behavior is mainly due to the fasteners and materials used and to the correct application of the capacity design approach. PMID:28793642

The nest architecture of the ant Odontomachus brunneus.

PubMed

Cerquera, Lina M; Tschinkel, Walter R

2010-01-01

The architecture of the subterranean nests of the ant Odontomachus brunneus (Patton) (Hymenoptera: Formicidae) was studied by means of casts with dental plaster or molten metal. The entombed ants were later recovered by dissolution of plaster casts in hot running water. O. brunneus excavates simple nests, each consisting of a single, vertical shaft connecting more or less horizontal, simple chambers. Nests contained between 11 and 177 workers, from 2 to 17 chambers, and 28 to 340 cm(2) of chamber floor space and reached a maximum depth of 18 to 184 cm. All components of nest size increased simultaneously during nest enlargement, number of chambers, mean chamber size, and nest depth, making the nest shape (proportions) relatively size-independent. Regardless of nest size, all nests had approximately 2 cm(2) of chamber floor space per worker. Chambers were closer together near the top and the bottom of the nest than in the middle, and total chamber area was greater near the bottom. Colonies occasionally incorporated cavities made by other animals into their nests.

Light Steel-Timber Frame with Composite and Plaster Bracing Panels.

PubMed

Scotta, Roberto; Trutalli, Davide; Fiorin, Laura; Pozza, Luca; Marchi, Luca; De Stefani, Lorenzo

2015-11-03

The proposed light-frame structure comprises steel columns for vertical loads and an innovative bracing system to efficiently resist seismic actions. This seismic force resisting system consists of a light timber frame braced with an Oriented Strand Board (OSB) sheet and an external technoprene plaster-infilled slab. Steel brackets are used as foundation and floor connections. Experimental cyclic-loading tests were conduced to study the seismic response of two shear-wall specimens. A numerical model was calibrated on experimental results and the dynamic non-linear behavior of a case-study building was assessed. Numerical results were then used to estimate the proper behavior factor value, according to European seismic codes. Obtained results demonstrate that this innovative system is suitable for the use in seismic-prone areas thanks to the high ductility and dissipative capacity achieved by the bracing system. This favorable behavior is mainly due to the fasteners and materials used and to the correct application of the capacity design approach.

A new seamless, smooth, interior, absorptive finishing system

NASA Astrophysics Data System (ADS)

D'Antonio, Peter

2003-10-01

Government architecture typically employs classic forms of vaults, domes and other focusing or reflective shapes, usually created with hard materials like concrete and plaster. The use of conventional porous absorption is typically rejected as an acoustical surface material for aesthetic reasons. Hence, many of these new and existing facilities have compromised speech intelligibility and music quality. Acousticians have sought a field-applied, absorptive finishing system that resembles a smooth plaster or painted drywall surface, since the dawn of architectural acoustics. Some success has been achieved using sprayed cellulose or cementitious materials, but surface smoothness has been a challenge. A new approach utilizing a thin microporous layer of mineral particles applied over a mineral wool panel will be described. This material can be applied to almost any shape surface, internally pigmented to match almost any color and renovated. Because of these unique characteristics the new seamless, absorptive, finishing system is being specified for many new and renovated spaces. Application examples will be presented.

Vector Blood Meals Are an Early Indicator of the Effectiveness of the Ecohealth Approach in Halting Chagas Transmission in Guatemala

PubMed Central

Pellecer, Mariele J.; Dorn, Patricia L.; Bustamante, Dulce M.; Rodas, Antonieta; Monroy, M. Carlota

2013-01-01

A novel method using vector blood meal sources to assess the impact of control efforts on the risk of transmission of Chagas disease was tested in the village of El Tule, Jutiapa, Guatemala. Control used Ecohealth interventions, where villagers ameliorated the factors identified as most important for transmission. First, after an initial insecticide application, house walls were plastered. Later, bedroom floors were improved and domestic animals were moved outdoors. Only vector blood meal sources revealed the success of the first interventions: human blood meals declined from 38% to 3% after insecticide application and wall plastering. Following all interventions both vector blood meal sources and entomological indices revealed the reduction in transmission risk. These results indicate that vector blood meals may reveal effects of control efforts early on, effects that may not be apparent using traditional entomological indices, and provide further support for the Ecohealth approach to Chagas control in Guatemala. PMID:23382165

Arts & Crafts for Everyone.

ERIC Educational Resources Information Center

Crane, Diane, Ed.

1982-01-01

Five different art activities, using different media, are described: (1) "mystery molds," using plaster and discarded packaging materials; (2) "calico cottages," using boxes and fabric; (3) "foam friends," using plastic foam packing pieces; (4) "bauble boxes," using spray can tops and papier mache; and (5) "soft stuff," using old clothing. (CJ)

29. Interior view, south end of the west (front) wall ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. Interior view, south end of the west (front) wall looking at the section between the door and southwestern corner, with scale (note remnants of the post-1915 fire plaster on wall) - Kiskiack, Naval Mine Depot, State Route 238 vicinity, Yorktown, York County, VA

Some Automated Cartography Developments at the Defense Mapping Agency.

DTIC Science & Technology

1981-01-01

on a pantographic router creating a laminate step model which was moulded in plaster for carving Into a terrain model. This section will trace DMA’s...offering economical automation. Precision flatbed Concord plotters were brought into DMA with sufficiently programmable control computers to perform these

Abestos in Buildings: The State Role.

ERIC Educational Resources Information Center

Neilander, Dennis K.; Sacarto, Douglas M.

1988-01-01

The widespread use of asbestos for several decades in building construction has created major public health concerns for state governments. If asbestos is not thoroughly bound in cement, plaster, resin or some other stable material, it will flake and powder, releasing countless microscopic fibers into the air. Asbestos fibers penetrate deep into…

Trade Masonry Syllabus.

ERIC Educational Resources Information Center

New York State Education Dept., Albany. Bureau of Occupational Education Curriculum Development.

Designed for a two-year course of study, this syllabus encompasses six areas of the masonry trade: concrete, block, brick, stone, tile, and plaster. For each area, the separate units of instruction contain course content outline, student behavioral objectives, and suggested teaching methods and audiovisuals. The six sections and their units are as…

Prevention of Pica, the Major Cause of Lead Poisoning in Children

ERIC Educational Resources Information Center

de la Burde, Brigitte; Reames, Betty

1973-01-01

Describes a study undertaken to establish a basis for various methods to combat the ingestion of plaster or paint containing lead by children from the lower socio-economic level. Stresses the need for the removal of substandard housing, case-finding, and early treatment of lead poisoning. (Author/SF)

Life-Size Sculptural Heads: A Lesson in Three-Dimensional Design.

ERIC Educational Resources Information Center

Gamble, Harriet

2003-01-01

Presents a lesson in which students created three-dimensional self-portraits, using papier-mache, clay, and plaster, designed to develop their modeling skills as they learn about art history. Discusses how the students created their sculptures, offering detailed directions on creating the three-dimensional heads. (CMK)

Got Sheetrock?

ERIC Educational Resources Information Center

Sheehan, Diane B.

2005-01-01

The author of this article, an art teacher, describes a high school studio lesson about sculptural reliefs using Sheetrock. She describes how students can work with and prepare Sheetrock and how they can create a design and transfer it onto the dry Sheetrock plaster. Making repairs to the surface, coloring and finishing, and the tools required are…

Plaster Relief Carving

ERIC Educational Resources Information Center

Hester, Vickie

2010-01-01

Two years ago, a fortuitous event occurred at the author's school: the pre-K classrooms across the hall from her artroom received a grant that covered the installation of new bathrooms inside the room. Despite the obvious benefits, this construction project generated one of the most engaging student art projects they've ever created: plaster…

In the Style of Henry Moore

ERIC Educational Resources Information Center

Hinshaw, Craig

2010-01-01

In this article, the author describes an art project inspired by Henry Moore's sculptures. This project consists of two activities. In the first activity, students select, sand and stain a wood block that would become a base for their plaster sculpture. This activity would keep the students independently engaged (classroom management) while the…

Balloon Sculpture

ERIC Educational Resources Information Center

Warwick, James F.

1976-01-01

For the adventurous teacher and student there is an alternative to the often messy mixing, pouring, casting, cutting, scoring and sanding of plaster of Paris for casting or sculptural projects. Balloon sculpture, devised, designed and shown here by a sculptor/teacher, is an eye appealing sculptural form and holds a strong interest for students.…

The Civil Rights Movement: A Humanities Rainbow

ERIC Educational Resources Information Center

Wheat, Brenda M.; Kapavik, Robin Robinson

2004-01-01

During recent renovation work at the Collin County Courthouse in a suburb of Dallas Texas, workers discovered "for colored" and "for white" signs underneath layers of plaster above the bathroom doors. The discovery has ignited controversy between citizens who are concerned with the eventual fate of the signs. Some residents of…

Sculpture: Creative Designs with Modern Materials (Tentative Course Outline).

ERIC Educational Resources Information Center

Dubocq, Edward R.

This document reports on a course in comprehension and application of various techniques of sculpture and collage, using a contemporary point of view. Students will work with contemporary materials such as wood, metals, plaster, plastics, styrofoam, and many other cardboard basic materials suitable for creative design products. This unit will…

Jobs in Construction. Job Family Series.

ERIC Educational Resources Information Center

Science Research Associates, Inc., Chicago, IL.

The booklet describes jobs in the construction industry under the classifications of public and private building. Separate chapters discuss the process of building a city hospital, a model home, and a State highway. Chapters outline miscellaneous jobs in the industry such as elevator constructors, lathers, plasterers, roofers, and sheet metal…

Interior building details of Building B, Room B004: south brick ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior building details of Building B, Room B-004: south brick wall partial painted brick plaster with stair scar trace, historic brick infilled arch entry way to Room C-001; southeasterly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

133. Historic American Buildings Survey R.A. Waugh, Photographer October 1936 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

133. Historic American Buildings Survey R.A. Waugh, Photographer October 1936 JAMB of WEST ROOM, 1st. FLOOR FIREPLACE SHOWING PLASTER & CORNER CHINKING - Colonel Paul Wentworth House, Dover Street (Salmon Falls, NH) (moved to Dover, MA, and then to 47 Water Street, Rollinsford, NH), Rollinsford, Strafford County, NH

132. INTERIOR, SIXTH FLOOR, WING 6100 WEST, SUITE 6000, ROOM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

132. INTERIOR, SIXTH FLOOR, WING 6100 WEST, SUITE 6000, ROOM 6156, OFFICE OF THE SECRETARY OF THE INTERIOR, PLASTER CEILING MEDALLION AND BRONZE CHANDELIER (4' x 5' negative; 8' x 10' print) - U.S. Department of the Interior, Eighteenth & C Streets Northwest, Washington, District of Columbia, DC

Exterior building details of Building A; east façade: profiled cement ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Exterior building details of Building A; east façade: profiled cement plaster door surround, black mesh gate protects a two-light transom atop non-original metal door; westerly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

Building Fossils in the Elementary School and Writing about Them Using Computers.

ERIC Educational Resources Information Center

Schlenker, Richard M.; Yoshida, Sarah

This material describes a fossil-building activity using sea shells, chicken bones, and plaster for grade one through three students. Related process skills, vocabulary, computer principles, time requirements, and materials are listed. Two methods of building the fossils are discussed. After building the fossils, classes may be divided into pairs…

Journey: A Service Learning Mural

ERIC Educational Resources Information Center

Gilman, Lisa

2009-01-01

Winthrop Middle School's cafeteria had three paintings on the wall in which the paint was fading and the plaster was falling off. Many students wanted a change since the paintings had been there for over 15 years. This situation seemed appropriate for a service learning project for this Winthrop, Maine middle school. After the students reviewed…

Using Aluminum Foil to Record Structures in Sedimentary Rock.

ERIC Educational Resources Information Center

Metz, Robert

1982-01-01

Aluminum foil can be used to make impressions of structures preserved in sedimentary rock. The impressions can be projected onto a screen, photographed, or a Plaster of Paris model can be made from them. Impressions of ripple marks, mudcracks, and raindrop impressions are provided in photographs illustrating the technique. (Author/JN)

Christmas Morning, Breakfast, Horace Pippin

ERIC Educational Resources Information Center

Braunlin-Jones, Heather

2004-01-01

This brief article describes the life and the art of Horace Pippin. It focuses on one work called "Christmas Morning, Breakfast" that is part of a series of works based on Pippin's childhood memories. The painting depicts a very modest room, including exposed wallboards where chunks of plaster have fallen off. The room is very tidy, but…

Painter and Decorator: Apprenticeship Course Outline. Apprenticeship and Industry Training. 0409

ERIC Educational Resources Information Center

Alberta Advanced Education and Technology, 2009

2009-01-01

The graduate of the Painter and Decorator apprenticeship program is a certified journeyperson who will be able to: (1) apply coatings by brush, roller and spray to surfaces of wood, metal, brick, concrete, plaster, stucco and stone for decorative and protective purposes. This occurs in residential, commercial, institutional and industrial…

Casting Freedom, 1860-1862

ERIC Educational Resources Information Center

Social Education, 2005

2005-01-01

Thomas Crawford, an American Sculptor, created the full-size figure of Freedom in clay. Molds were made, from which a full-size positive plaster model was cast in five main sections. This model is on view today in the basement rotunda of the Russell Senate Office Building. Clark Mills was a self-taught American sculptor with experience in casting…

Bury my Face in Casting Plaster

ERIC Educational Resources Information Center

Judnick, Don

1976-01-01

As part of an introductory course in figure drawing, art students spent some time doing portrait studies and profile drawings. When the teacher threw in an ancedote on life masks, it had a double impact. Students learned to better understand underlying bone structure and facial planes and to create a new art product. (Author/RK)

THE DEVELOPMENT OF THE TEACHING SPACE DIVIDER.

ERIC Educational Resources Information Center

BELLOMY, CLEON C.; CAUDILL, WILLIAM W.

TYPES OF VERTICAL WORK SURFACES AND THE DEVELOPMENT OF A MODEL TEACHING SPACE DIVIDER ARE DISCUSSED IN THIS REPORT. THIS DESIGN IS BASED ON THE EXPRESSED NEED FOR MORE TACKBOARD AND SHELVING SPACE, AND FOR MOVABLE PARTITIONS. THE MODEL PANELS WHICH SERVE DIRECTLY AS PARTITIONS RATHER THAN BEING OVERLAID ON A PLASTERED SURFACE, INCLUDE THE…

Improper tube fixation causing a leaky cuff.

PubMed

Gupta, Babita; Farooque, Kamran; Jain, Divya; Kapoor, Rakesh

2010-04-01

Leaking endotracheal tube cuffs are common problems in intensive care units. We report a case wherein the inflation tube was damaged by the adhesive plaster used for tube fixation and resulted in leaking endotracheal tube cuff. We also give some suggestions regarding the tube fixation and some remedial measures for damaged inflation system.

ATTITUDE OF CLEFT CARE SPECIALISTS IN AFRICA TOWARDS PRESURGICAL ORTHOPAEDICS.

PubMed

Adeyemi, A T; Bankole, O O

2012-12-01

To determine the attitude of cleft care specialists working in Africa towards pre-surgical orthopaedics. A cross sectional study. Pan-African conference on cleft lip and palate in Nigeria. Sixty cleft care specialists working in Africa. The general attitude towards pre-surgicalorthopaedics was positive. Majority of the specialists employ pre-surgical orthopaedics before surgical repair. Fifty four (91%) of the specialists use plaster strapping for cases of bilateral cleft, five (8.3%) use nasoalveolar molding and one (2%) use feeding plate. Half of the specialists (50%) felt that pre-surgical orthopaedics is to be managed by orthodontists alone. There were significant difference in attitude towards pre-surgical orthopaedics between providers (p < 0.05). Orthodontists had a strong positive attitude towards pre-surgical orthopaedics than other specialists. Younger specialists had a more positive attitude towards pre-surgical orthopaedics than older specialists. Cleft care specialists in Africa have a positive attitude towards pre-surgical orthopaedics. Majority of them use plaster strapping technique. Younger specialists have a more favorable attitude towards pre-surgical orthopaedics than older specialists.

Creation of 3D Multi-Body Orthodontic Models by Using Independent Imaging Sensors

PubMed Central

Barone, Sandro; Paoli, Alessandro; Razionale, Armando Viviano

2013-01-01

In the field of dental health care, plaster models combined with 2D radiographs are widely used in clinical practice for orthodontic diagnoses. However, complex malocclusions can be better analyzed by exploiting 3D digital dental models, which allow virtual simulations and treatment planning processes. In this paper, dental data captured by independent imaging sensors are fused to create multi-body orthodontic models composed of teeth, oral soft tissues and alveolar bone structures. The methodology is based on integrating Cone-Beam Computed Tomography (CBCT) and surface structured light scanning. The optical scanner is used to reconstruct tooth crowns and soft tissues (visible surfaces) through the digitalization of both patients' mouth impressions and plaster casts. These data are also used to guide the segmentation of internal dental tissues by processing CBCT data sets. The 3D individual dental tissues obtained by the optical scanner and the CBCT sensor are fused within multi-body orthodontic models without human supervisions to identify target anatomical structures. The final multi-body models represent valuable virtual platforms to clinical diagnostic and treatment planning. PMID:23385416

Creation of 3D multi-body orthodontic models by using independent imaging sensors.

PubMed

Barone, Sandro; Paoli, Alessandro; Razionale, Armando Viviano

2013-02-05

In the field of dental health care, plaster models combined with 2D radiographs are widely used in clinical practice for orthodontic diagnoses. However, complex malocclusions can be better analyzed by exploiting 3D digital dental models, which allow virtual simulations and treatment planning processes. In this paper, dental data captured by independent imaging sensors are fused to create multi-body orthodontic models composed of teeth, oral soft tissues and alveolar bone structures. The methodology is based on integrating Cone-Beam Computed Tomography (CBCT) and surface structured light scanning. The optical scanner is used to reconstruct tooth crowns and soft tissues (visible surfaces) through the digitalization of both patients' mouth impressions and plaster casts. These data are also used to guide the segmentation of internal dental tissues by processing CBCT data sets. The 3D individual dental tissues obtained by the optical scanner and the CBCT sensor are fused within multi-body orthodontic models without human supervisions to identify target anatomical structures. The final multi-body models represent valuable virtual platforms to clinical diagnostic and treatment planning.

Experimental layering development by indenter technique and application to fault rheology differentiation

NASA Astrophysics Data System (ADS)

Gratier, J. P.; Noiriel, C. N.; Renard, F.

2014-12-01

Natural deformation of rocks is often associated with differentiation processes leading to irreversible transformations of their microstructural thus leading in turn to modifications of their rheological properties. The mechanisms of development of such processes at work during diagenesis, metamorphism or fault differentiation are poorly known as they are not easy to reproduce in the laboratory due to the long duration required for most of chemically controlled differentiation processes. Here we show that experimental compaction with layering development, similar to what happens in natural deformation, can be obtained in the laboratory by indenter techniques. Samples of plaster mixed with clay and samples of diatomite loosely interbedded with clays were loaded during several months at 40°C (plaster) and 150°C (diatomite) in presence of their saturated solutions. High-resolution X-ray tomography and SEM studies show that the layering development is a self-organized process. Stress driven dissolution of the soluble minerals (gypsum in plaster, silica in diatomite) is initiated in the zones initially richer in clays because the kinetics of diffusive mass transfer along the clay/soluble mineral interfaces is much faster than along the healed boundaries of the soluble minerals. The passive concentration of the clay minerals amplifies the localization of the dissolution along some layers oriented perpendicular to the maximum compressive stress component. Conversely, in the areas with initial low content in clay and clustered soluble minerals, dissolution is more difficult as the grain boundaries of the soluble species are healed together. These areas are less deformed and they act as rigid objects that concentrate the dissolution near their boundaries thus amplifying the differentiation. Applications to fault processes are discussed: i) localized pressure solution and sealing processes may lead to fault rheology differentiation with a partition between two end-member behaviors: seismic (in sealed zones) and aseismic (in dissolved zones); ii) tectonic layering may lead to highly anisotropic structures with a drastic decrease of the rock strength parallel to the layering.

Efficacy and evaluation of environmental management system to control sandfly vector of Kala-azar.

PubMed

Dinesh, D S; Kumari, S; Hassan, F; Kumar, V; Singh, V P; Das, P

2017-10-01

The established vector for visceral leishmaniasis, Phlebotomus argentipes (Diptera: Psychodidae) breeds inside the human dwellings and cattle shed under crevices at the base of the wall. P. argentipes was controlled by plastering the base of wall (9″height × 9″base). The study was conducted in two phases: (i) Screening of plastering materials (ii) validation of the most suitable material. During the first phase (2014); four intervention materials were evaluated in four different arms: (i) cement (ii) brick chimney fly ash (BCFA i.e. waste material from an oven for backing raw earthen brick in charcoal) mixed with lime (95:5) (iii) wire mesh (25 holes/cm 2 ) and (iv) glazed tiles. Ten houses were selected as test and same as control in four different villages for each arm having similar ecotype and similar density of sandflies. The pre and post intervention density of sandflies were evaluated. Significant reduction in sandfly density was found with cement (46.2%) and BCFA (29.6%) plastering (P < 0.05). In the second phase of the study (2015); the two most effective interventions were validated at village level with one control. A significant reduction in the density of P. argentipes was found with cement; 60.2% (Mean ± S.D. = 2.48 ± 2.78, 95% CI = 1.93-3.02) and BCFA; 48.2% (Mean ± S.D. = 1.98 ± 2.20, 95% CI = 1.55-2.41) (P < 0.05). BCFA was found easily accessible, acceptable and cost effective that can be used in any type of wall materials at own cost. This can be implemented as one of the integrated vector control approach in the programme. Copyright © 2017. Published by Elsevier Ltd.

A comparison of the accuracy of polyether, polyvinyl siloxane, and plaster impressions for long-span implant-supported prostheses.

PubMed

Hoods-Moonsammy, Vyonne J; Owen, Peter; Howes, Dale G

2014-01-01

The purpose of this study was to compare the capacity of different impression materials to accurately reproduce the positions of five implant analogs on a master model by comparing the resulting cast with the stainless steel master model. The study was motivated by the knowledge that distortions can occur during impression making and the pouring of casts and that this distortion may produce inaccuracies of subsequent restorations, especially long-span castings for implant superstructures. The master model was a stainless steel model with five implant analogs. The impression materials used were impression plaster (Plastogum, Harry J Bosworth), a polyether (Impregum Penta, 3M ESPE), and two polyvinyl siloxane (PVS) materials (Aquasil Monophase and Aquasil putty with light-body wash, Dentsply). Five impressions were made with each impression material and cast in die stone under strictly controlled laboratory conditions. The positions of the implants on the master model, the impression copings, and the implant analogs in the subsequent casts were measured using a coordinate measuring machine that measures within 4 μm of accuracy. Statistical analyses indicated that distortion occurred in all of the impression materials, but inconsistently. The PVS monophase material reproduced the master model most accurately. Although there was no significant distortion between the impressions and the master model or between the impressions and their casts, there were distortions between the master model and the master casts, which highlighted the cumulative effects of the distortions. The polyether material proved to be the most reliable in terms of predictability. The impression plaster displayed cumulative distortion, and the PVS putty with light body showed the least reliability. Some of the distortions observed are of clinical significance and likely to contribute to a lack of passive fit of any superstructure. The inaccuracy of these analog materials and procedures suggested that greater predictability may lie in digital technology.

Earth mineral resource of the month: asbestos

USGS Publications Warehouse

Virta, Robert L.

2010-01-01

The article discusses the characteristics and feature of asbestos. According to the author, asbestos is a generic name for six needle-shaped minerals that possess high tensile strengths, flexibility, and resistance to chemical and thermal degradation. These minerals are actinolite, amosite, anthophyllite, chrysolite, crocilodite and tremolite. Asbestos is used for strengthening concrete pipe, plastic components, and gypsum plasters.

Masonry Specialist III & IV, 3-20. Military Curriculum Materials for Vocational and Technical Education.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. National Center for Research in Vocational Education.

These military-developed curriculum materials consist of a course description, plan of instruction, study guides, and workbooks for use in training masonry specialists. Covered in the course blocks are laying concrete blocks, stone, and bricks as well as plaster, stucco, and tile. Course block III, on laying concrete blocks, stone, and bricks,…

American History Brought to Life

ERIC Educational Resources Information Center

Teague, Joetta

2011-01-01

For the past twenty years, a major project for the author's eighth-grade art classes has been a group diorama with plaster figures. The group has to include two to four people participating in a sport or an occupation while showing some kind of action and interaction. Not too long ago, a couple of girls asked to depict the signing of the…

Plasterer (const.) 5-29.100--Technical Report on Standardization of the General Aptitude Test Battery.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

Special Operations, Irregular Warfare, and Operational Art: A Theory of Special Operations

DTIC Science & Technology

2013-12-10

is mostly but not wholly a land phenomenon. Naval forces have combatted maritime irregulars such as pirates for millennia, for example see: Plutarch ...SW2502SocialMediaAndUW.html (accessed June 15, 2013). Plaster, John L. SOG: Secret Wars of America’s Commandos in Vietnam. New York: Simon & Schuster, 1997. Plutarch

Effects of Metric Change on Workers’ Tools and Training.

DTIC Science & Technology

1981-07-01

understanding of the metric system, and particularly a lack of fluency in converting customary measurements to metric measuremerts, may increase the...assembly, installing, and repairing occupations 84 Painting, plastering, waterproofing, cementing , and related occupations 85 Excavating, grading... cementing , and related occupations 85 Excavating, grading, paving, and related occupations 86 Construction occupations, n.e.c. 89 Structural work

Masonry: Construction Industry Series: Preparation Level: Student Manual and Instructor's Guide.

ERIC Educational Resources Information Center

Texas Education Agency, Austin. Dept. of Occupational Education and Technology.

The guide is an outline of training experiences designed to lead a student to at least entry-level job proficiency in the masonry trades within the construction industry. Teaching units cover concrete working, brick and block layering, plastering, and tile and terrazzo working. Each unit has several overall objectives which are divided into…

PRODUCTION OF SLIP CAST CALCIA HOLLOWWARE

DOEpatents

Stoddard, S.D.; Nuckolls, D.E.; Cowan, R.E.

1963-12-31

A method for producing slip cast calcia hollow ware in which a dense calcia grain is suspended in isobutyl acetate or a mixture of tertiary amyl alcohol and o-xylene is presented. A minor amount of triethanolamine and oleic acid is added to the suspension vehicle as viscosity adjusting agents and the suspension is cast in a plaster mold, dried, and fired. (AEC)

Philip Reid and the Statue of Freedom

ERIC Educational Resources Information Center

Walton, Eugene

2005-01-01

The Statue of Freedom stands at the very top of the dome of the Capitol, where Congress meets in Washington, D.C. The dome, with its statue, is a symbol recognized all over the world. Thomas Crawford, an American sculptor, created the Statue of Freedom in clay in a studio in Rome, Italy. A plaster model was cast in five major sections and shipped…

You Can Hide but You Can't Run: Interdisciplinary and Culturally Sensitive Approaches to Mask Making

ERIC Educational Resources Information Center

Ballengee-Morris, Christine

2005-01-01

From papier mache to plaster and paper to moulage, making masks is a popular activity for both art educators and students around the world. Masks have been and are currently used by many cultures/societies for specific cultural rituals and spiritual, metaphorical, role-playing, and theatrical reasons. In short, their use and their creation are…

Plaster Trimmer (dental equip.) 712.887; Inserter (dental equip.) 712.884--Technical Report on Development of USTES Aptitude Test Battery.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

21 CFR 358.550 - Labeling of corn and callus remover drug products.

Code of Federal Regulations, 2010 CFR

2010-04-01

... formulated in a collodion-like vehicle. (i) “If product gets into the eye, flush with water for 15 minutes...(a). “Wash affected area and dry thoroughly.” (If appropriate: “Cut plaster to fit corn/callus... in § 358.510(b). “Wash affected area and dry thoroughly. Apply” (select one of the following, as...

21 CFR 358.550 - Labeling of corn and callus remover drug products.

Code of Federal Regulations, 2012 CFR

2012-04-01

... formulated in a collodion-like vehicle. (i) “If product gets into the eye, flush with water for 15 minutes...(a). “Wash affected area and dry thoroughly.” (If appropriate: “Cut plaster to fit corn/callus... in § 358.510(b). “Wash affected area and dry thoroughly. Apply” (select one of the following, as...

21 CFR 358.550 - Labeling of corn and callus remover drug products.

Code of Federal Regulations, 2014 CFR

2014-04-01

... formulated in a collodion-like vehicle. (i) “If product gets into the eye, flush with water for 15 minutes...(a). “Wash affected area and dry thoroughly.” (If appropriate: “Cut plaster to fit corn/callus... in § 358.510(b). “Wash affected area and dry thoroughly. Apply” (select one of the following, as...

21 CFR 358.550 - Labeling of corn and callus remover drug products.

Code of Federal Regulations, 2011 CFR

2011-04-01

... formulated in a collodion-like vehicle. (i) “If product gets into the eye, flush with water for 15 minutes...(a). “Wash affected area and dry thoroughly.” (If appropriate: “Cut plaster to fit corn/callus... in § 358.510(b). “Wash affected area and dry thoroughly. Apply” (select one of the following, as...

21 CFR 358.550 - Labeling of corn and callus remover drug products.

Code of Federal Regulations, 2013 CFR

2013-04-01

... formulated in a collodion-like vehicle. (i) “If product gets into the eye, flush with water for 15 minutes...(a). “Wash affected area and dry thoroughly.” (If appropriate: “Cut plaster to fit corn/callus... in § 358.510(b). “Wash affected area and dry thoroughly. Apply” (select one of the following, as...

9. Typical 'furnished rooms' overlook the Washington Street alley. Each ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. Typical 'furnished rooms' overlook the Washington Street alley. Each has two double-hung windows that are fitted with roller-shade brackets. The plaster was formulated with lime and is heavily laden with animal hair. Each room is provided with a stove-pipe connection. Credit GADA/MRM. - Stroud Building, 31-33 North Central Avenue, Phoenix, Maricopa County, AZ

Buttons to Bumper Stickers: Political Campaign Memorabilia--Campaign Memorabilia Can Help Students Connect Past with Present

ERIC Educational Resources Information Center

Potter, Lee Ann

2004-01-01

During the season of political campaigns scores of bumper stickers, posters, and other items with slogans supporting one candidate or another suddenly appear and quickly multiply around neighborhoods and towns, with stickers plastered on cars, and posters hanging in windows, or posted in front yards. From George Washington to George W. Bush,…

33. Detail of ceiling light at exit from floor of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

33. Detail of ceiling light at exit from floor of auditorium to lobby (Aisle 3). Identical lights are seen on the ceiling above the mezzanine loge as seen in WA-197-34. The large white spot in WA-197-33 is a chip in the painted plaster. (July 1991) - Fox Theater, Seventh Avenue & Olive Way, Seattle, King County, WA

77 FR 49863 - Pacific Imperial Railroad, Inc.-Change in Operator Exemption-Rail Line of San Diego and Arizona...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-17

... Railroad, Inc.--Change in Operator Exemption-- Rail Line of San Diego and Arizona Eastern Railway Company... Plaster City, Cal. (Desert Line).\\2\\ The Desert Line is owned by San Diego and Arizona Eastern Railway... Diego Metropolitan Transit Development Board, and SD&IV. \\1\\ CGR was authorized to operate the Desert...

New methods and materials for molding and casting ice formations

NASA Technical Reports Server (NTRS)

Reehorst, Andrew L.; Richter, G. Paul

1987-01-01

This study was designed to find improved materials and techniques for molding and casting natural or simulated ice shapes that could replace the wax and plaster method. By utilizing modern molding and casting materials and techniques, a new methodology was developed that provides excellent reproduction, low-temperature capability, and reasonable turnaround time. The resulting casts are accurate and tough.

Casting and Splinting

DTIC Science & Technology

2017-08-21

mcludmg suggost1ons klr reducing lite burden, to the Department ar Defense. Executive Service Director> lte (07,IJ4-0188). Respondents should be...Orthoglass) Casting Material );;:- Fiberglass , .... • \\ \\ General Principles )- Measure out dry material at extremity being treated ~Plaster...shrinks slightly when wet; If too long can fold ends back ~Can be measured on contralateral extremity > Apply 2-3 layers of webril, avoid wrinkles

Exterior building details of Building C, east façade: historic six ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Exterior building details of Building C, east façade: historic six light entry double door with three light transom, historic six light door with a one light transom, arch brick lintels and quoins, scored cement plaster finished brick walls; westerly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

Plaster mortars with polymer fibers and additives investigated by 1H NMR relaxometry

NASA Astrophysics Data System (ADS)

Mustea, Andrei; Manea, Daniela L.; Jumate, Elena; Orbán, Yvette A.; Fechete, Radu

2017-12-01

Plaster mortars with polypropylene (pp) fibers and/or additives were investigated by 1H NMR relaxometry. Two recipes are proposed and are based on a commercially available mortar or are self-prepared and have different content of polypropylene fibers, which play the role of reinforcement agent, and/or Sika additive which is a waterproofing agent. The distributions of transverse relaxation times, T2 were obtained at 1, 3, 7 and 28 days after preparation. For the majority of T2-distributions four peaks are observed and, are associated with the hydration water (to the mineralogical components) and water in small, medium and large pores. The evolution in time, from 1 to 28 days, of the T2-distributions indicates the effects of pp fibers and Sika additive in the formation of pore microstructure. The degree of homogeneity of prepared receipts was evaluated from the relative peak-width and compared with mechanical measurements. Finally, we shown that the inverse of the transverse relaxation time values, T2-1, characteristic to the hydration water depends linearly on the resistance at compression measured for the 1÷28 days period, proving the important role of hydrations to the mechanical properties of the final product.

Spectroscopic analysis of XIV century wall paintings from Patriarchate of Peć Monastery, Serbia

NASA Astrophysics Data System (ADS)

Marić-Stojanović, M.; Bajuk-Bogdanović, D.; Uskoković-Marković, S.; Holclajtner-Antunović, I.

2018-02-01

The Church of the Holy Mother of God Hodegetria in Peć is decorated with wall paintings that date from the beginning of the 14th century. In terms of style they correspond to Byzantine wall paintings from the epoch of Paleologos. The painting technique and pigment pallete has been examined on micro fragments in thin cross-sections by means of optical microscopy (OM), scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS) and micro- Raman spectroscopy. Use of the fresco technique and two supporting plaster layers was noted on the majority of samples, while in large blue painted areas, a combination of fresco and secco techniques was used. The SEM-EDS results showed the presence of Ca as the main component of plaster besides the traces of Si and Mg. In some samples egg white as a binder was identified. The paint film is often multilayered. Twelve pigments were identified, mainly natural earth pigments such as red ochre, yellow ochre and green earth. A mixture of pigments was used for attaining desirable optical and aesthetical impressions. As decay product only weddelite was detected in many preparatory and painted samples.

Diagnostic accuracy and measurement sensitivity of digital models for orthodontic purposes: A systematic review.

PubMed

Rossini, Gabriele; Parrini, Simone; Castroflorio, Tommaso; Deregibus, Andrea; Debernardi, Cesare L

2016-02-01

Our objective was to assess the accuracy, validity, and reliability of measurements obtained from virtual dental study models compared with those obtained from plaster models. PubMed, PubMed Central, National Library of Medicine Medline, Embase, Cochrane Central Register of Controlled Clinical trials, Web of Knowledge, Scopus, Google Scholar, and LILACs were searched from January 2000 to November 2014. A grading system described by the Swedish Council on Technology Assessment in Health Care and the Cochrane tool for risk of bias assessment were used to rate the methodologic quality of the articles. Thirty-five relevant articles were selected. The methodologic quality was high. No significant differences were observed for most of the studies in all the measured parameters, with the exception of the American Board of Orthodontics Objective Grading System. Digital models are as reliable as traditional plaster models, with high accuracy, reliability, and reproducibility. Landmark identification, rather than the measuring device or the software, appears to be the greatest limitation. Furthermore, with their advantages in terms of cost, time, and space required, digital models could be considered the new gold standard in current practice. Copyright © 2016 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Influence of Cellulosic Fibres on the Physical Properties of Fibre Cement Composites

NASA Astrophysics Data System (ADS)

Hospodarova, V.; Stevulova, N.; Vaclavik, V.; Dvorsky, T.

2017-10-01

Nowadays, there are new approaches directing to processing of non-conventional fibre-cement composites for application in the housing construction. Vegetable cellulosic fibres coming from natural resources used as reinforcement in cost-effective and environmental friendly building products are in the spotlight. The applying of natural fibres in cement based composites is narrowly linked to the ecological building sector, where a choice of materials is based on components including recyclable, renewable raw materials and low-resource manufacture techniques. In this paper, two types of cellulosic fibres coming from wood pulp and recycled waste paper with 0.2%; 0.3% and 0.5% of fibre addition into cement mixtures were used. Differences in the physical characteristics (flowability, density, coefficient of thermal conductivity and water absorbability) of 28 days hardened fibre-cement composites are investigated. Addition of cellulosic fibres to cement mixture caused worsening the workability of fresh mixture as well as absorbability of hardened composites due to hydrophilic nature of biomaterial, whereas density and thermal conductivity of manufactured cement based fibre plaster are enhanced. The physical properties of cement plasters based on cellulosic fibres depend on structural, physical characteristics of cellulosic fibres, their nature and processing.

Ballistic Trauma of Limbs.

PubMed

Lamah, Léopold; Keita, Damany; Marie Camara, Ibrahima; Lamine Bah, Mohamed; Sory, Sidimé; Diallo, Mamadou Moustapha

2017-01-01

The objective of our study was to report the management and follow-up of a particular case of ballistic trauma and to do the literature review. A 35-year-old patient, a trader who was the victim of a firearm accident under not very clear circumstances. He was admitted to the emergency department after 3 hours. Clinically, the patient had significant bleeding in the arm and was in a state of clouding of consciousness. We could notice on the right arm, a posterior large transfixing wound of 1 cm and a 6 cm one on the antero-internal side. The limb was cold with a small and thready pulse. Sensitivity was decreased in the radial nerve area. The radiograph showed bone comminution from the middle 1/3 to the superior 1/3 of the humeral diaphysis. The treatment was orthopedic (after debridement) by scapula-brachio-ante-brachiopalmar plaster splint with thoracic strap. The wound healed in 46 days and the patient resumed his activities after 11 months and 2 weeks. The authors presented the value of using the scapulo-brachio-palmar plaster splints with thoracic strap in some severe upper limb trauma in the absence of the external fixator.

Ballistic Trauma of Limbs

PubMed Central

Lamah, Léopold; Keita, Damany; Marie Camara, Ibrahima; Lamine Bah, Mohamed; Sory, Sidimé; Diallo, Mamadou Moustapha

2017-01-01

The objective of our study was to report the management and follow-up of a particular case of ballistic trauma and to do the literature review. Observation: A 35-year-old patient, a trader who was the victim of a firearm accident under not very clear circumstances. He was admitted to the emergency department after 3 hours. Clinically, the patient had significant bleeding in the arm and was in a state of clouding of consciousness. We could notice on the right arm, a posterior large transfixing wound of 1 cm and a 6 cm one on the antero-internal side. The limb was cold with a small and thready pulse. Sensitivity was decreased in the radial nerve area. The radiograph showed bone comminution from the middle 1/3 to the superior 1/3 of the humeral diaphysis. The treatment was orthopedic (after debridement) by scapula-brachio-ante-brachiopalmar plaster splint with thoracic strap. The wound healed in 46 days and the patient resumed his activities after 11 months and 2 weeks. Conclusion: The authors presented the value of using the scapulo-brachio-palmar plaster splints with thoracic strap in some severe upper limb trauma in the absence of the external fixator. PMID:28567155

Comparative study on stiffness properties of WOODCAST and conventional casting materials.

PubMed

Pirhonen, Eija; Pärssinen, Antti; Pelto, Mika

2013-08-01

Plaster-of-Paris and synthetic materials (e.g. fibreglass) have been in clinical use as casting materials for decades. An innovative casting material, WOODCAST, brings interesting alternatives to the traditional materials. The aim of this study was to compare the stiffness properties of the WOODCAST material to traditional casting materials. In immobilization by casting, materials with variable stiffness properties are required. Ring stiffness of cylindrical samples correlates well with cast rigidity. For load-bearing structures, the use of the WOODCAST Splint is recommended as equally high stiffness was obtained with the WOODCAST Splint as was with fibreglass. The WOODCAST 2 mm product is optimal for structures where some elasticity is required, and WOODCAST Ribbon can be used in any WOODCAST structure where further reinforcement is needed. The results show that WOODCAST material can be used in replacing traditional casting materials used in extremity immobilization. The mechanical properties of casting material play an important role in safe and effective fracture immobilization. Stiffness properties of the WOODCAST casting material and conventional materials - fibreglass and plaster-of-Paris - were analysed in this study. The WOODCAST Splint appears to compare favorably with traditional materials such as Scotchcast.

The Necessity for the Military Assistance Command--Vietnam Studies and Observations Group

DTIC Science & Technology

2015-06-12

officials, as well as then-Colonel Edward Lansdale. An opponent of President Eisenhower’s laissez - faire attitude towards French Colonialism, the... leadership since the military was now tasked to 3 John Plaster, SOG: The Secret Wars of America’s...University of California Press Berkeley, 1972), 2. 9 oversee covert military actions. The military leadership argued that covert actions were not

The pathology of innactivation in monkeys.

NASA Technical Reports Server (NTRS)

Bourne, G. H.; Golarz De Bourne, M. N.; Mcclure, H.; Keeling, M.

1973-01-01

Progress report on a long-term experiment using rhesus monkeys and designed to study the effects of isolation up to one year, as well as the effects of bed rest simulated by immobilization in a plaster cast for six months. The investigation includes histopathological and histochemical studies of these effects on various internal organs and tissues, and some of the preliminary results of these studies are presented and discussed.

56. ORIGINAL MOLDS. THE MORAVIAN POTTERY AND TILE WORKS HAS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

56. ORIGINAL MOLDS. THE MORAVIAN POTTERY AND TILE WORKS HAS APPROXIMATELY 6,000 PLASTER MOLDS OF VARIOUS TYPES, INCLUDING THE DEEP CAVITY MOLDS IN THE CENTER OF THE PHOTOGRAPH. THESE MOLDS PRODUCED ALLEGORICAL FIGURES TO BE INSTALLED AROUND THE CORNICES OF PUBLIC SCHOOLS. - Moravian Pottery & Tile Works, Southwest side of State Route 313 (Swamp Road), Northwest of East Court Street, Doylestown, Bucks County, PA

Mineral resource of the month: vermiculite

USGS Publications Warehouse

Potter, M.J.

2008-01-01

Vermiculite, a hydrated magnesium-aluminum-iron silicate mineral, has a range of uses that take advantage of its fire resistance, good insulating properties, high liquid absorption capacity, inertness and low density. Most applications for vermiculite use an exfoliated (heat-expanded) form of the mineral. In general, coarser grades of vermiculite are used as loose fill insulation and in horticulture. Finer grades are used in wallboard and plasters and for animal feeds and fertilizers.

Effects of immobilization on articular cartilage: Autohistoradiographic findings with S35

NASA Technical Reports Server (NTRS)

Digiovanni, C.; Desantis, E.

1980-01-01

The effect of immobilization on the articular cartilage of rabbits was studied by light microscope. The knee joint of each rabbit was immobilized in a plaster in a position midway between flexion and extension for a 10 to 120 days period. Degenerative changes in the articular cartilage of increasing severity were observed. The fixation of the labeled SO4 by cartilage cells was decreased in advanced immobilization.

Mineral resource of the month: perlite

USGS Publications Warehouse

,

2010-01-01

The article talks about perlite, which is a mineral used as an aggregate for lightweight construction products, filler for paints and horticultural soil blends. Perlite comes from viscous lava, mined and processed to produce lightweight material that competes with pumice, exfoliated vermiculite and expanded clay and shale. It is mined in about 35 countries that include Greece, Japan and the U.S. Other uses include insulation, concrete and plaster aggregate, and stonewashing.

15. Photocopy of photograph (Original print, Wallie V. Funk Collection.) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. Photocopy of photograph (Original print, Wallie V. Funk Collection.) Photographer unknown. Published in the Anacortes American, 12 October 1911; 'Plant of the Anacortes Ice Company and Curtis Dock.' Photograph probably earlier. View looking northwest, left to right; Cement and Plaster Warehouse; Ice Plant (with towers); Cold Storage Warehouse; Freight Warehouse; a warehouse; and early ticket office. - Curtis Wharf, O & Second Streets, Anacortes, Skagit County, WA

Prosthetics & Orthotics Manufacturing Initiative (POMI)

DTIC Science & Technology

2012-12-21

the two materials. The rod was then put onto a lathe machine, allowing a thin sheet, with stripes of alternating materials, to be cut from the rod...tooling from. Mentis determined a method to use Aquacore, which involved machining blanks via CNC , followed by coating the mold to prevent resin...infusion into the mold. Mentis also attempted to use plaster combined with CNC machining, however, these molds did not survive the machining process

1. 119 LOMBARD STREET, SECOND HOUSE TO LEFT (WITH BOARDEDUP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. 119 LOMBARD STREET, SECOND HOUSE TO LEFT (WITH BOARDED-UP FIRST AND SECOND FLOOR WINDOWS). NOTE THAT THE FRONT (SOUTH) HAS BELT COURSES, GLAZED HEADERS, PLASTER COVE CORNICE, DOOR STOOP, ETC. ALSO NOTE THE TWIN HOUSE (117 LOMBARD STREET, HABS No. PA-1353) AT RIGHT, WITH IDENTICAL FEATURES. BOTH HOUSES WERE BUILT AT THE SAME TIME. - Joseph Wharton House, 119 Lombard Street, Philadelphia, Philadelphia County, PA

The Subgenus Persicargas (Ixodoidea, Argasidae, Argas). Part 2. Ecology and Seasonal Dynamics of A. (P). Arboreus, Kaiser, Hoogstraal and Kohls in Egypt

DTIC Science & Technology

1971-10-30

tube closed at 1 end by a plaster and Aulad Nigmr Bahgura. Nag Hammadi (Iboth of Paris plug and covered by muslin at the other Qena Governorate), and El...Ilindaw, Dakhla 4,11d. The tubes were put in paper cups in outdoor Oasis (El Wadi el Gedid Governorate) (Hoogstraal shade beside the NAMRU-3 Medical

3D printed facial laser scans for the production of localised radiotherapy treatment masks - A case study.

PubMed

Briggs, Matthew; Clements, Helen; Wynne, Neil; Rennie, Allan; Kellett, Darren

This study investigates the use of 3D printing for patients that require localised radiotherapy treatment to the face. The current process involves producing a lead mask in order to protect the healthy tissue from the effects of the radiotherapy. The mask is produced by applying a thermoplastic sheet to the patient's face and allowing to set hard. This can then be used as a mould to create a plaster impression of the patient's face. A sheet of lead is then hammered on to the plaster to create a bespoke fitted face mask. This process can be distressing for patients and can be problematic when the patient is required to remain motionless for a prolonged time while the thermoplastic sets. In this study, a 1:1 scale 3D print of a patient's face was generated using a laser scanner. The lead was hammered directly on to the surface of the 3D print in order to create a bespoke fitted treatment mask. This eliminated the thermoplastic moulding stage and significantly reduced the time needed for the patient to be in clinic. The higher definition impression of the the face resulted in a more accurate, better fitting treatment mask.

Comparison of different techniques for obturating experimental internal resorptive cavities.

PubMed

Goldberg, F; Massone, E J; Esmoris, M; Alfie, D

2000-06-01

Forty extracted maxillary central incisors were instrumented at the working length to a #50 file. The roots were sectioned transversely with a diamond disk at 7 mm from the anatomical apex. At the opening of the root canal of each section, hemicircular cavities were drilled with a specially designed bur. The corresponding root sections were cemented with glue, thus obtaining root canals with similar cavities that simulated internal resorptions. Teeth were embedded in plaster casts to facilitate their handling. The specimens were randomly separated into four groups of 10. The following obturation techniques were evaluated: lateral compaction (group A), hybrid technique (group B), Obtura II (group C), and Thermafil (group D). AH26 was used as the sealer. After obturation, the plaster was removed and the teeth were radiographed in buccolingual and mesiodistal directions to evaluate the quality of the obturation at the IRC. The incisors were then cut with a scalpel at the same level as the previous section, to examine, under a stereomicroscope, the type of material that filled the IRC. Obtura II gave the best results and in most of the specimens obturated with this technique, the IRC were filled mainly with gutta-percha. Statistical analysis of the data indicated that the differences between group C and the other groups were significant (P < 0.05).

Activities and impairments in the early stage of rehabilitation after Colles' fracture.

PubMed

Dekkers, Merete; Søballe, Kjeld

2004-06-03

The purpose of this study was to investigate problems in performing activities after Colles' fracture, and to correlate activity limitations with impairments in the early stage of rehabilitation. Assessments were performed 1 and 5 weeks after removing plaster casts. A client-specific instrument, The Canadian Occupational Performance Measure, and a disease-specific dichotomous scale of 10 activities of daily living were used. Range of motion, grip strength, pain and dexterity were also assessed according to standardized methods. Thirty-three women, aged 51-87 years, with Colles' fracture treated with closed reduction and a plaster cast participated. Highly significant statistical and clinical improvements were found in the capacity, number and performance of activities. Problems were mainly classified as self-care activities at 1 week, and as productivity activities at 5 weeks, while problems in leisure activities were practically the same. However, one-third of the patients were not able to perform all basic activities of daily living at 5 weeks. Improvements in pain frequency, range of motion, grip strength and dexterity did not correlate very well with improvements in performance or the patients' satisfaction with the performance of their activities. The importance of assessing both impairments and activities in patients with Colles' fracture must be stressed.

Significance of ultrasound in the diagnosis and treatment of achilles tendon rupture.

PubMed

Poposka, A; Georgieva, D; Dzoleva-Tolevska, R

2012-01-01

The aim of this study is to show the importance of ultrasound method in the diagnosis of Achilles tendon rupture, the choice of method of treatment and monitoring of treatment using the same method. Between 1999 and 2009, 134 patients with Achilles tendon rupture were referred to our Clinic. 66 patients (with a mean age of 38 years) were treated with surgical suture followed by plaster immobilization for a period of 8 weeks. 68 patients (with a mean age of 42 years) were treated conservatively with plaster immobilization for a period of 8 weeks. The follow-up in both groups of patients was 2 years. During the clinical and ultrasound monitoring of the patients it was proved that repeated rupture of the same tendon occurs on average within 12 months. Return to sports activities showed in 57% of the conservatively treated patients and in 55% of surgically treated patients. The patients with Achilles tendon rupture were treated at our Clinic with previously standardized protocol which, besides the clinical examination, used the ultrasound method. Ultrasound examination is a very important method in the diagnosis and the choice of the method of treatment, as well as in the evaluation of results in patients with Achilles tendon rupture, either in operative or conservative treatment.

Engineering specification and system design for CAD/CAM of custom shoes: UMC project effort

NASA Technical Reports Server (NTRS)

Bao, Han P.

1990-01-01

Further experimentations were made to improve the design and fabrication techniques of the integrated sole. The sole design is shown to be related to the foot position requirements and the actual shape of the foot including presence of neurotropic ulcers or other infections. Factors for consideration were: heel pitch, balance line, and rigidity conditions of the foot. Machining considerations were also part of the design problem. Among these considerations, widths of each contour, tool motion, tool feed rate, depths of cut, and slopes of cut at the boundary were the key elements. The essential fabrication techniques evolved around the idea of machining a mold then, using quick-firm latex material, casting the sole through the mold. Two main mold materials were experimented with: plaster and wood. Plaster was very easy to machine and shape but could barely support the pressure in the hydraulic press required by the casting process. Wood was found to be quite effective in terms of relative cost, strength, and surface smoothness except for the problem of cutting against the fibers which could generate ragged surfaces. The programming efforts to convert the original dBase programs into C programs so that they could be executed on the SUN Computer at North Carolina State University are discussed.

Populations of some molds in water-damaged homes may ...

EPA Pesticide Factsheets

Starting in the 1940s, gypsum drywall began replacing plaster and lathe in the U.S. home construction industry. Our goal was to evaluate whether some mold populations differ in water- damaged homes primarily constructed with gypsum drywall compared to plaster. The dust samples from the 2006 Department of Housing and Urban Development's (HUD) American Health Homes Survey (AHHS) were the subject of this analysis. The concentrations of the 36 Environmental Relative Moldiness Index (ERMI) molds were compared in homes of different ages. The homes (n = 301) were built between 1878 and 2005. Homes with ERMI values > 5 (n = 126) were defined as water-damaged. Homes with ERMI values > 5 were divided in the years 1976 to 1977 into two groups, i.e., older (n = 61) and newer (n = 65). Newer water-damaged homes had significantly (p = 0.002) higher mean ERMI values than older water-damaged homes, 11.18 and 8.86, respectively. The Group 1 molds Aspergillus flavus, Ammophilus fumigatus, Aspergillus ochraceus, Cladosporium sphaerospermum and Trichoderma viride were found in significantly higher concentrations in newer compared to older high-ERMI homes. Some mold populations in water-damaged homes may have changed after the introduction of gypsum drywall. This research provides insight into the asthma epidemic in the US.

A comparison of the clinical effectiveness of spinal orthoses manufactured using the conventional manual method and CAD/CAM method in the management of AIS.

PubMed

Wong, M S; Cheng, C Y; Ng, B K W; Lam, T P; Chiu, S W

2006-01-01

Spinal orthoses are commonly prescribed to patients with moderate AIS for prevention of further deterioration. In a conventional manufacturing method, plaster bandages are used to get patient's body contour and plaster cast is rectified manually. With the introduction of CAD/CAM system, a series of automated processes from body scanning to digital rectification and milling of positive model can be performed in a fast and accurate fashion. This project is to study the impact of CAD/CAM method as compared with the conventional method. In assessing the 147 recruited subjects fitted with spinal orthoses (43 subjects using conventional method and 104 subjects using CAD/CAM method), significant decreases (p<0.05) were found in the Cobb angles when comparing the pre-intervention data with that of the first year of intervention. Regarding the learning curve, Orthotists are getting more competent with the CAD/CAM technique in four years time. The mean productivity of the CAD/CAM method is 2.75 times higher than that of the conventional method. The CAD/CAM method could achieve similar clinical outcomes and with its high efficiency, could be considered as substitute for conventional methods in fabricating spinal orthoses for patients with AIS.

8. MACHINERY SHED STORAGE ROOM ADDITION DETAIL SHOWING MATRIX OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. MACHINERY SHED STORAGE ROOM ADDITION DETAIL SHOWING MATRIX OF NAILS USED TO ADHERE PORTLAND CEMENT PLASTER, SOUTH ADOBE WALL ADJACENT TO WINDOW Note: Photographs Nos. AZ-159-A-9 through AZ-159-A-10 are photocopies of photographs. The original prints and negatives are located in the SCS Tucson Plant Materials Center, Tucson, Arizona. Photographer Ted F. Spaller. - Tucson Plant Material Center, Machinery Shed, 3241 North Romero Road, Tucson, Pima County, AZ

Structural Integrity Assessment Using Laser Measured Surface Vibration

DTIC Science & Technology

2009-04-01

catastrophic failure of the plaster ceiling and the unrecoverable loss of priceless artwork. Several years ago, Bucaro et . al .1 and Vignola et . al .3...eliminating the requirement for scaffolding. Although such an acoustic speaker approach had been introduced and applied to frescoes by Castellini, et . al .15...and later applied by Tornari et . al .16 to mosaics, ceramics, inlaid wood, and easel paintings, both these and subsequent studies using speaker (or

Orthognathic model surgery with LEGO key-spacer.

PubMed

Tsang, Alfred Chee-Ching; Lee, Alfred Siu Hong; Li, Wai Keung

2013-12-01

A new technique of model surgery using LEGO plates as key-spacers is described. This technique requires less time to set up compared with the conventional plaster model method. It also retains the preoperative setup with the same set of models. Movement of the segments can be measured and examined in detail with LEGO key-spacers. Copyright © 2013 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Swarming and the Future of Warfare

DTIC Science & Technology

2005-01-01

the horse archers swarmed around the square and began delivering arrows and spears from standoff range. As Plutarch described it, "The Parthians thus...cutting it off, surrounded and annihilated it. The harassment of the main body continued until nightfall, when the darkness prevented 2 Plutarch ...Plaster, John L. SOG: The Secret Wars of America’s Commandos in Vietnam. New York, NY: Penguin Group, 1997. Plutarch . Selected Lives from the Lives of Noble

Surgery versus conservative treatment in patients with type A distal radius fractures, a randomized controlled trial

PubMed Central

2014-01-01

Background Fractures of the distal radius are common and account for an estimated 17% of all fractures diagnosed. Two-thirds of these fractures are displaced and require reduction. Although distal radius fractures, especially extra-articular fractures, are considered to be relatively harmless, inadequate treatment may result in impaired function of the wrist. Initial treatment according to Dutch guidelines consists of closed reduction and plaster immobilisation. If fracture redisplacement occurs, surgical treatment is recommended. Recently, the use of volar locking plates has become more popular. The aim of this study is to compare the functional outcome following surgical reduction and fixation with a volar locking plate with the functional outcome following closed reduction and plaster immobilisation in patients with displaced extra-articular distal radius fractures. Design This single blinded randomised controlled trial will randomise between open reduction and internal fixation with a volar locking plate (intervention group) and closed reduction followed by plaster immobilisation (control group). The study population will consist of all consecutive adult patients who are diagnosed with a displaced extra-articular distal radius fracture, which has been adequately reduced at the Emergency Department. The primary outcome (functional outcome) will be assessed by means of the Disability Arm Shoulder Hand Score (DASH). Secondary outcomes comprise the Patient-Rated Wrist Evaluation score (PRWE), quality of life, pain, range of motion, radiological parameters, complications and cross-overs. Since the treatment allocated involves a surgical procedure, randomisation status will not be blinded. However, the researcher assessing the outcome at one year will be unaware of the treatment allocation. In total, 90 patients will be included and this trial will require an estimated time of two years to complete and will be conducted in the Academic Medical Centre Amsterdam and its partners of the regional trauma care network. Dicussion Ideally, patients would be randomised before any kind of treatment has been commenced. However, we deem it not patient-friendly to approach possible participants before adequate reduction has been obtained. Trial registration This study is registered at the Netherlands Trial Register (NTR3113) and was granted permission by the Medical Ethical Review Committee of the Academic Medical Centre on 01-10-2012. PMID:24642190

Final Environmental Assessment for Decommissioning and Demolition of the Central Heat Plant, GHLN 09-1010B F. E. Warren Air Force Base, Wyoming

DTIC Science & Technology

2012-06-01

could either be accomplished by installing a solar heating panel on the roof of each of the 104 buildings or having a solar photovoltaic array...Prior to 1981 , ACMs were used extensively in plaster, wall board, joint compound, felt material , roofing material , floor tile , mastic, piping...5 5.4. Alternative D-lnstall Solar Heating Panels or Solar Photovoltaic Array ......................... 5 5.5. Alternative E

Polyvinyl siloxane: novel material for external nasal splinting.

PubMed

Jayakumar, N K; Rathnaprabhu, V; Ramesh, S; Parameswaran, A

2016-01-01

External nasal splinting is performed routinely after nasal bone fracture reductions, osteotomies, and rhinoplasties. Materials commonly used include plaster of Paris (POP), thermoplastic splints, self-adhesive padded aluminium splints, and Orthoplast, among many others. The disadvantages of these materials are described in this paper, and polyvinyl siloxane is recommended as an effective and more readily available alternative material to counter these pitfalls. Copyright © 2015 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

3-dimensional orthodontics visualization system with dental study models and orthopantomograms

NASA Astrophysics Data System (ADS)

Zhang, Hua; Ong, S. H.; Foong, K. W. C.; Dhar, T.

2005-04-01

The aim of this study is to develop a system that provides 3-dimensional visualization of orthodontic treatments. Dental plaster models and corresponding orthopantomogram (dental panoramic tomogram) are first digitized and fed into the system. A semi-auto segmentation technique is applied to the plaster models to detect the dental arches, tooth interstices and gum margins, which are used to extract individual crown models. 3-dimensional representation of roots, generated by deforming generic tooth models with orthopantomogram using radial basis functions, is attached to corresponding crowns to enable visualization of complete teeth. An optional algorithm to close the gaps between deformed roots and actual crowns by using multi-quadratic radial basis functions is also presented, which is capable of generating smooth mesh representation of complete 3-dimensional teeth. User interface is carefully designed to achieve a flexible system with as much user friendliness as possible. Manual calibration and correction is possible throughout the data processing steps to compensate occasional misbehaviors of automatic procedures. By allowing the users to move and re-arrange individual teeth (with their roots) on a full dentition, this orthodontic visualization system provides an easy and accurate way of simulation and planning of orthodontic treatment. Its capability of presenting 3-dimensional root information with only study models and orthopantomogram is especially useful for patients who do not undergo CT scanning, which is not a routine procedure in most orthodontic cases.

Inter-crosslinking network gels having both shape memory and high ductility

NASA Astrophysics Data System (ADS)

Amano, Yoshitaka; Hidema, Ruri; Furukawa, Hidemitsu

2012-04-01

Medical treatment for injuries should be easy and quick in many accidents. Plasters or bandages are frequently used to wrap and fix injured parts. If plasters or bandages have additional smart functions, such as cooling, removability and repeatability, they will be much more useful and effective. Here we propose innovative biocompatible materials, that is, nontoxic high-strength shape-memory gels as novel smart medical materials. These smart gels were prepared from two monomers (DMAAm and SA), a polymer (HPC), and an inter-crosslinking agent (Karenz-MOI). In the synthesis of the gels, 1) a shape-memory copolymer network is made from the DMAAm and the SA, and 2) the copolymer and the HPC are crosslinked by the Karenz-MOI. Thus the crosslinking points are connected only between the different polymers. This is our original technique of developing a new network structure of gels, named Inter-Crosslinking Network (ICN). The ICN gels achieve high ductility, going up to 700% strain in tensile tests, while the ICN gels contain about 44% water. Moreover the SA has temperature dependence due to its crystallization properties; thus the ICN gels obtain shape memory properties and are named ICN-SMG. While the Young's modulus of the ICN-SMG is large below their crystallization temperature and the gels behave like plastic materials, the modulus becomes smaller above the temperature and the gels turn back to their original shape.

Study on compressive strength of self compacting mortar cubes under normal & electric oven curing methods

NASA Astrophysics Data System (ADS)

Prasanna Venkatesh, G. J.; Vivek, S. S.; Dhinakaran, G.

2017-07-01

In the majority of civil engineering applications, the basic building blocks were the masonry units. Those masonry units were developed as a monolithic structure by plastering process with the help of binding agents namely mud, lime, cement and their combinations. In recent advancements, the mortar study plays an important role in crack repairs, structural rehabilitation, retrofitting, pointing and plastering operations. The rheology of mortar includes flowable, passing and filling properties which were analogous with the behaviour of self compacting concrete. In self compacting (SC) mortar cubes, the cement was replaced by mineral admixtures namely silica fume (SF) from 5% to 20% (with an increment of 5%), metakaolin (MK) from 10% to 30% (with an increment of 10%) and ground granulated blast furnace slag (GGBS) from 25% to 75% (with an increment of 25%). The ratio between cement and fine aggregate was kept constant as 1: 2 for all normal and self compacting mortar mixes. The accelerated curing namely electric oven curing with the differential temperature of 128°C for the period of 4 hours was adopted. It was found that the compressive strength obtained from the normal and electric oven method of curing was higher for self compacting mortar cubes than normal mortar cube. The cement replacement by 15% SF, 20% MK and 25%GGBS obtained higher strength under both curing conditions.

How can periorbital oedema and ecchymose be reduced in rhinoplasty?

PubMed

Caglar, Erdem; Celebi, Saban; Topak, Murat; Develioglu, Necati Omer; Yalcin, Enis; Kulekci, Mehmet

2016-09-01

Oedema and ecchymose are frequent morbidities of septorhinoplasty, a facial surgical procedure for reforming the shape and functions of the nose. Periorbital oedema (PO) and periorbital ecchymose (PE) are normal occurrences, but are undesirable for patients undergoing the procedure for aesthetic purposes. The present study examined 65 patients who underwent open technique septorhinoplasty for aesthetic and functional complaints. Patients were divided into two groups: Group 1 patients underwent lateral osteotomy following tip plasty, at the end of the surgical operation; Group 2 patients underwent lateral osteotomy before tip plasty, at the beginning of the surgical operation. Patients were followed on the postoperative first, third and seventh days. PO and PE values of patients were scored from 0 to 4. The plastering time (Pt) was significantly shorter for Group I than Group II (p < 0.05). The total surgical time (T) showed no significant difference (p > 0.05). The PO value at the first, third and seventh days was significantly smaller for Group I than Group II (p < 0.05). The PE value at the first, third and seventh days was also significantly smaller for Group I than Group II (p < 0.05). The obtained data indicate that performing a lateral osteotomy in the final stages of surgery, and subsequently applying a nasal plaster and splint as rapidly as possible, decreases PO and PE in the postoperative period.

The identity of Penicillium sp. 1, a major contaminant of the stone chambers in the Takamatsuzuka and Kitora Tumuli in Japan, is Penicillium paneum.

PubMed

An, Kwang-Deuk; Kiyuna, Tomohiko; Kigawa, Rika; Sano, Chie; Miura, Sadatoshi; Sugiyama, Junta

2009-11-01

Penicillium appeared as the major dweller in the Takamatsuzuka Tumulus (TT) and Kitora Tumulus (KT) stone chambers, both located in the village of Asuka, Nara Prefecture, in relation to the biodeterioration of the 1,300-year-old mural paintings, plaster walls and ceilings. Of 662 Penicillium isolates from 373 samples of the TT (sampling period, May 2004-2007) and the KT (sampling period, June 2004-Sep 2007), 181 were phenotypically assigned as Penicillium sp. 1 which shared similar phenotypic characteristics of sect. Roqueforti in Penicillium subg. Penicillium. Fifteen representative isolates of Penicillium sp. 1, 13 from TT and 2 from KT, were selected for molecular phylogenetic analysis. The 28S rDNA D1/D2, ITS, beta-tubulin, and lys2 gene sequence-based phylogenies clearly demonstrated that the three known species P. roqueforti, P. carneum and P. paneum in sect. Roqueforti, and all TT and KT isolates grouped together. In addition to this, TT and KT isolates formed a monophyletic group with the ex-holotype strain CBS 101032 of P. paneum Frisvad with very strong bootstrap supports. So far, P. paneum has been isolated only from mouldy rye breads, other foods, and baled grass silage. Therefore, this is the first report of P. paneum isolation from samples relating to the biodeteriorated cultural properties such as mural paintings on plaster walls.

[Manufacture method and clinical application of minimally invasive dental implant guide template based on registration technology].

PubMed

Lin, Zeming; He, Bingwei; Chen, Jiang; D u, Zhibin; Zheng, Jingyi; Li, Yanqin

2012-08-01

To guide doctors in precisely positioning surgical operation, a new production method of minimally invasive implant guide template was presented. The mandible of patient was scanned by CT scanner, and three-dimensional jaw bone model was constructed based on CT images data The professional dental implant software Simplant was used to simulate the plant based on the three-dimensional CT model to determine the location and depth of implants. In the same time, the dental plaster models were scanned by stereo vision system to build the oral mucosa model. Next, curvature registration technology was used to fuse the oral mucosa model and the CT model, then the designed position of implant in the oral mucosa could be determined. The minimally invasive implant guide template was designed in 3-Matic software according to the design position of implant and the oral mucosa model. Finally, the template was produced by rapid prototyping. The three-dimensional registration technology was useful to fuse the CT data and the dental plaster data, and the template was accurate that could provide the doctors a guidance in the actual planting without cut-off mucosa. The guide template which fabricated by comprehensive utilization of three-dimensional registration, Simplant simulation and rapid prototyping positioning are accurate and can achieve the minimally invasive and accuracy implant surgery, this technique is worthy of clinical use.

Digital terrain tapes: user guide

USGS Publications Warehouse

,

1980-01-01

DMATC's digital terrain tapes are a by-product of the agency's efforts to streamline the production of raised-relief maps. In the early 1960's DMATC developed the Digital Graphics Recorder (DGR) system that introduced new digitizing techniques and processing methods into the field of three-dimensional mapping. The DGR system consisted of an automatic digitizing table and a computer system that recorded a grid of terrain elevations from traces of the contour lines on standard topographic maps. A sequence of computer accuracy checks was performed and then the elevations of grid points not intersected by contour lines were interpolated. The DGR system produced computer magnetic tapes which controlled the carving of plaster forms used to mold raised-relief maps. It was realized almost immediately that this relatively simple tool for carving plaster molds had enormous potential for storing, manipulating, and selectively displaying (either graphically or numerically) a vast number of terrain elevations. As the demand for the digital terrain tapes increased, DMATC began developing increasingly advanced digitizing systems and now operates the Digital Topographic Data Collection System (DTDCS). With DTDCS, two types of data elevations as contour lines and points, and stream and ridge lines are sorted, matched, and resorted to obtain a grid of elevation values for every 0.01 inch on each map (approximately 200 feet on the ground). Undefined points on the grid are found by either linear or or planar interpolation.

Efficacy of S-flurbiprofen plaster in knee osteoarthritis treatment: Results from a phase III, randomized, active-controlled, adequate, and well-controlled trial.

PubMed

Yataba, Ikuko; Otsuka, Noboru; Matsushita, Isao; Matsumoto, Hideo; Hoshino, Yuichi

2017-01-01

S-flurbiprofen plaster (SFPP) is a novel non-steroidal anti-inflammatory drug (NSAID) patch, intended for topical treatment for musculoskeletal diseases. This trial was conducted to examine the effectiveness of SFPP using active comparator, flurbiprofen (FP) patch, on knee osteoarthritis (OA) symptoms. This was a phase III, multi-center, randomized, adequate, and well-controlled trial, both investigators and patients were blinded to the assigned treatment. Enrolled 633 knee OA patients were treated with either SFPP or FP patch for two weeks. The primary endpoint was improvement in knee pain on rising from the chair as assessed by visual analogue scale (rVAS). Safety was evaluated through adverse events (AEs). The change in rVAS was 40.9 mm in SFPP group and 30.6 mm in FP patch group (p < 0.001). The incidence of drug-related AEs at the application site was 9.5% (32 AEs, 29 mild and 3 moderate) in SFPP and 1.6% in FP patch (p < 0.001). Withdrawals due to AE were five in SFPP and one in FP patch. The superiority of SFPP in efficacy was demonstrated. Most of AEs were mild and few AEs led to treatment discontinuation. Therefore, SFPP provides an additional option for knee OA therapy.

[Cohort study of the incidence of heel pressure sores in patients with leg casts at the Rizzoli Orthopedic Hospital and of the associated risk factors].

PubMed

Forni, Cristiana; Zoli, Marina; Loro, Loretta; Tremosini, Morena; Mini, Sandra; Pirini, Valter; Turrini, Roberta; Durante, Stefano; Nicolini, Annamaria; Riccioni, Francesca; Girolami, Roberto

2009-01-01

Pressure sores, especially at the heel, are a side effect of the cast. To assess the incidence of late skin complications (heel pressure sores) of a cast and determine risk factors. All consecutive patients treated with a leg cast over a 16 months observation time were recruited. Risk factors were identified by the nurse that placed the cast and skin lesions classified with the NPUAP scale when the cast was removed. In the 216 enrolled patients 17.6% (38) developed a pressure sore: 16/124 in orthopedic wards; 22/92 in oncology wards. The multivariate analysis identified the following risk factors: administration of cytotoxic drugs (p = 0.033; OR = 2.61; having a cancer did not increase the risk); skin redness before cast application (p = 0.001; OR = 4.44) and having reported symptoms after the application (p = 0.000; OR = 7.86). Pressure sores were mainly stage 1 and only 6/216 (2.4%) > or = stage II. The type of plaster cast, the material, the number of days it was worn and having had a surgery are not significant risk factors. Pressure sores related to leg plaster casts are a frequent complication in at risk sub-groups. The acknowledgement and identification of specific risk factors may allow to identify and evaluate preventive interventions to improve the care of these patients.

Immobilization rapidly induces thioredoxin-interacting protein (TXNIP) gene expression together with insulin resistance in rat skeletal muscle.

PubMed

Kawamoto, Emi; Tamakoshi, Keigo; Ra, Song-Gyu; Masuda, Hiroyuki; Kawanaka, Kentaro

2018-05-24

Acute short-duration of disuse induces the development of insulin resistance for glucose uptake in rodent skeletal muscle. Since thioredoxin-interacting protein (TXNIP) has been implicated in the downregulation of insulin signaling and glucose uptake, we examined the possibility that muscle disuse rapidly induces insulin resistance via increased TXNIP mRNA and protein expression. Male Wistar rats were subjected to unilateral 6-hr hindlimb immobilization by plaster cast. At the end of this period, the soleus muscles from both immobilized and contralateral non-immobilized hindlimbs were excised and examined. The 6-hr immobilization resulted in an increase in TXNIP mRNA and protein expressions together with a decrease in insulin-stimulated 2-deoxyglucose uptake in the rat soleus muscle. Additionally, in the rats sacrificed 6 hr after the plaster cast removal, TXNIP protein expression and insulin-stimulated glucose uptake in the immobilized muscle had both been restored to a normal level. Various interventions (pretreatment with transcription inhibitor actinomycin D or AMPK activator AICAR) also suppressed the increase in TXNIP protein expression in 6-hr-immobilized muscle together with partial prevention of insulin resistance for glucose uptake. These results suggested the possibility that increased TXNIP protein expression in immobilized rat soleus muscles was associated with the rapid induction of insulin resistance for glucose uptake in that tissue.

Triatoma maculata colonises urban domicilies in Boa Vista, Roraima, Brazil

PubMed Central

Ricardo-Silva, Alice; Gonçalves, Teresa Cristina Monte; Luitgards-Moura, José Francisco; Lopes, Catarina Macedo; da Silva, Silvano Pedrosa; Bastos, Amanda Queiroz; Vargas, Nathalia Coelho; Freitas, Maria-Rosa Goreti

2016-01-01

During a medical entomology course in Boa Vista, Roraima, colonies of Triatoma maculata closely associated with pigeon nests were observed in concrete air-conditioner box located on the external plastered and cemented walls of a modern brick-built apartment block. In only one eight-hole ceramic brick, located inside one air-conditioner box, 127 specimens of T. maculata were collected. T. maculata is a recognised vector of Trypanosoma cruzi in the surrounding area and its domiciliation increases the risk of Chagas disease transmission. PMID:27759767

Triatoma maculata colonises urban domicilies in Boa Vista, Roraima, Brazil.

PubMed

Ricardo-Silva, Alice; Gonçalves, Teresa Cristina Monte; Luitgards-Moura, José Francisco; Lopes, Catarina Macedo; Silva, Silvano Pedrosa da; Bastos, Amanda Queiroz; Vargas, Nathalia Coelho; Freitas, Maria-Rosa Goreti

2016-11-01

During a medical entomology course in Boa Vista, Roraima, colonies of Triatoma maculata closely associated with pigeon nests were observed in concrete air-conditioner box located on the external plastered and cemented walls of a modern brick-built apartment block. In only one eight-hole ceramic brick, located inside one air-conditioner box, 127 specimens of T. maculata were collected. T. maculata is a recognised vector of Trypanosoma cruzi in the surrounding area and its domiciliation increases the risk of Chagas disease transmission.

Jefferson Proving Ground, South of the Firing Line, Final Asbestos Survey Summary Report. Volume 3. Buildings 230 through 475

DTIC Science & Technology

1993-09-01

interior is finished with plaster or wallboard (i.e., sheetrock, drywall, gypsum board , etc.) walls and ceilings, "cheese-cloth" wall and ceiling lining...with wallboard (i.e., sheetrock, drywall, gypsum board , etc.) walls and ceilings, acoustical ceiling panels/tiles, and vinyl tile or bare concrete...finished with wallboard (i.e., sheetrock, drywall, gypsum board , etc.) walls and ceilings, and vinyl tile or bare concrete floors. "* No fireproofing or

Netra darpanamu - A Unique book on eye diseases

PubMed Central

Prasad, Goli Penchala

2007-01-01

Netra Darpanamu is the only book written exclusively on Eye diseases in Telugu. This Ayurvedic book, which is famous in Andhra Pradesh, was first published in 1908 in Eluru. The book is written in chaste Telugu poetry, comprising the types of treatment followed by 36 recipes. This book contains names of various eye diseases, treatment procedures like bandages, plasters, collyriums and regimen of food and behaviour. This article aims to highlight the importance of this book in treating various eye diseases. PMID:22557269

Does an employee assistance programme benefit employers and employees alike?

PubMed

MacAlister, E

1999-09-01

EAPs are not a psychological sticking plaster. They are a clinically and corporately balanced service which benefits the employee, via the direct services and the employer, via the feedback in the form of usage statistics derived from the continuous tracking of the account through which organizational and employment issues are identified. Well positioned EAPs offer employees confidential counselling, and information services including legal, financial and child-based issues and are able to offer employers tailored training and consultancy.

The neuropathic foot.

PubMed

Jernberger, A

1993-12-01

The neuropathic foot is described with relation to cause, presentation, dysfunction and identification. The various mechanisms of neuropathic foot lesions are outlined--overload, diabetic gangrene, continuous pressure, direct injury and cutting and temperature effects. The orthotic treatment of the foot is discussed and in particular the importance of proper shoe provision and patient education and indoctrination emphasised. The use of plaster casts and fenestrations to control pressure distribution is described. Finally results of an intensive treatment programme are presented to identify the effect on outcome, as measured by delay in amputation.

Raman scattering or fluorescence emission? Raman spectroscopy study on lime-based building and conservation materials.

PubMed

Kaszowska, Zofia; Malek, Kamilla; Staniszewska-Slezak, Emilia; Niedzielska, Karina

2016-12-05

This work presents an in-depth study on Raman spectra excited with 1064 and 532nm lasers of lime binders employed in the past as building materials and revealed today as valuable conservation materials. We focus our interest on the bands of strong intensity, which are present in the spectra of all binders acquired with laser excitation at 1064nm, but absent in the corresponding spectra acquired with laser excitation at 532nm. We suggest, that the first group of spectra represents fluorescence phenomena of unknown origin and the second true Raman scattering. In our studies, we also include two other phases of lime cycle, i.e. calcium carbonate (a few samples of calcite of various origins) and calcium oxide (quicklime) to assess how structural and chemical transformations of lime phases affect the NIR-Raman spectral profile. Furthermore, we analyse a set of carbonated limewashes and lime binders derived from old plasters to give an insight into their spectral characteristics after excitation with the 1064nm laser line. NIR-Raman micro-mapping results are also presented to reveal the spatial distribution of building materials and fluorescent species in the cross-section of plaster samples taken from a 15th century chapel. Our study shows that the Raman analysis can help identify lime-based building and conservation materials, however, a caution is advised in the interpretation of the spectra acquired using 1064nm excitation. Copyright © 2016. Published by Elsevier B.V.

Accuracy of digital American Board of Orthodontics Discrepancy Index measurements.

PubMed

Dragstrem, Kristina; Galang-Boquiren, Maria Therese S; Obrez, Ales; Costa Viana, Maria Grace; Grubb, John E; Kusnoto, Budi

2015-07-01

A digital analysis that is shown to be accurate will ease the demonstration of initial case complexity. To date, no literature exists on the accuracy of the digital American Board of Orthodontics Discrepancy Index (DI) calculations when applied to pretreatment digital models. Plaster models were obtained from 45 previous patients with varying degrees of malocclusion. Total DI scores and the target disorders were computed manually with a periodontal probe on the original plaster casts (gold standard) and digitally using Ortho Insight 3D (Motion View Software, Hixson, Tenn) and OrthoCAD (Cadent, Carlstadt, NJ). Intrarater and interrater reliabilities were assessed for 15 subjects using the Spearman rho correlation test. Accuracies of the DI scores and target disorders were assessed for all 45 subjects using Wilcoxon signed ranks tests. Intrarater and interrater reliabilities were high for total DI scores and most target disorders (r > 0.8). No significant difference was found between total DI score when measured with OrthoCAD compared with manual calculations. The total DI scores calculated by Ortho Insight 3D were found to be significantly greater than those by manual calculation by 2.71 points. The findings indicate that a DI calculated by Ortho Insight 3D may lead the clinician to overestimate case complexity. OrthoCAD's DI module was demonstrated to be a clinically acceptable alternative to manual calculation of the total scores. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Acupuncture for post anaesthetic recovery and postoperative pain: study protocol for a randomised controlled trial.

PubMed

Fleckenstein, Johannes; Baeumler, Petra I; Gurschler, Caroline; Weissenbacher, Tobias; Simang, Michael; Annecke, Thorsten; Geisenberger, Thomas; Irnich, Dominik

2014-07-21

We report on the design and implementation of a study protocol entitled Acupuncture randomised trial for post anaesthetic recovery and postoperative pain - a pilot study (ACUARP) designed to investigate the effectiveness of acupuncture therapy performed in the perioperative period on post anaesthetic recovery and postoperative pain. The study is designed as a randomised controlled pilot trial with three arms and partial double blinding. We will compare (a) press needle acupuncture, (b) no treatment and (c) press plaster acupressure in a standardised anaesthetic setting. Seventy-five patients scheduled for laparoscopic surgery to the uterus or ovaries will be allocated randomly to one of the three trial arms. The total observation period will begin one day before surgery and end on the second postoperative day. Twelve press needles and press plasters are to be administered preoperatively at seven acupuncture points. The primary outcome measure will be time from extubation to 'ready for discharge' from the post anaesthesia care unit (in minutes). The 'ready for discharge' end point will be assessed using three different scores: the Aldrete score, the Post Anaesthetic Discharge Scoring System and an In-House score. Secondary outcome measures will comprise pre-, intra- and postoperative variables (which are anxiety, pain, nausea and vomiting, concomitant medication). The results of this study will provide information on whether acupuncture may improve patient post anaesthetic recovery. Comparing acupuncture with acupressure will provide insight into potential therapeutic differences between invasive and non-invasive acupuncture techniques. NCT01816386 (First received: 28 October 2012).

Efficacy of lidocaine 5% medicated plaster (VERSATIS®) in patients with localized neuropathic pain poorly responsive to pharmacological therapy.

PubMed

Martini, Alvise; Del Balzo, Giovanna; Schweiger, Vittorio; Zanzotti, Michele; Picelli, Alessandro; Parolini, Massimo; Chinellato, Eris; Tamburin, Stefano; Polati, Enrico

2018-05-31

Localized neuropathic pain (LNP) is a subgroup of neuropathic pain characterized by consistent and circumscribed area(s) of maximum pain, associated with negative or positive sensory signs and/or spontaneous symptoms characteristic of NP. Lidocaine medicated plasters (LMP) have shown to be effective in pain relief in selective LNP syndromes. We collected data of 130 patients in our database with LNP syndromes who used LMP. Forty-one patients out of 130 patients(32%) were treated with antiepileptics, antidepressants and opioids without improvement and/or with intolerable adverse effects and are not assuming systemic therapy anymore. Globally, during the 12 months follow-up, 15% of patients reached a complete pain relief without any systemic therapy, mainly in trigeminal and post-herpetic neuralgia (p=0.009), 38% of patients reduced analgesic drug consumption with the highest reduction in radiculopathy, post-herpetic neuralgia and trigeminal neuralgia. Topical and transient adverse effects, such as itching or local erythema, were seen in 19/130 (14.6%) patients; 7 of these patients (5.4%) needed to discontinue the treatment due to the occurrence of adverse effects. The dropout rate on global population (excluding cured and lost to follow up) was 45%, and the main cause of dropouts was the inefficacy of treatment in the first 3 months of therapy with LMP. LMP treatment is safe and worth consideration also as add-on therapy in order to reduce analgesic drug consumption in selected LNP.

Topical Anti-Inflammatory and Analgesic Effects of Multiple Applications of S(+)-Flurbiprofen Plaster (SFPP) in a Rat Adjuvant-Induced Arthritis Model.

PubMed

Sugimoto, Masanori; Toda, Yoshihisa; Hori, Miyuki; Mitani, Akiko; Ichihara, Takahiro; Sekine, Shingo; Kaku, Shinsuke; Otsuka, Noboru; Matsumoto, Hideo

2016-06-01

Preclinical Research The aim of this study was to evaluate the efficacy of multiple applications of S(+)-flurbiprofen plaster (SFPP), a novel Nonsteroidal anti-inflammatory drug (NSAID) patch, for the alleviation of inflammatory pain and edema in rat adjuvant-induced arthritis (AIA) model as compared to other NSAID patches. The AIA model was induced by the injection of Mycobacterium butyricum and rats were treated with a patch (1.0 cm × 0.88 cm) containing each NSAID (SFP, ketoprofen, loxoprofen, diclofenac, felbinac, flurbiprofen, or indomethacin) applied to the paw for 6 h per day for 5 days. The pain threshold was evaluated using a flexion test of the ankle joint, and the inflamed paw edema was evaluated using a plethysmometer. cyclooxygenase (COX)-1 and COX-2 inhibition was evaluated using human recombinant proteins. Multiple applications of SFPP exerted a significant analgesic effect from the first day of application as compared to the other NSAID patches. In terms of paw edema, SFPP decreased edema from the second day after application, Multiple applications of SFPP were superior to those of other NSAID patches, in terms of the analgesic effect with multiple applications. These results suggest that SFPP may be a beneficial patch for providing analgesic and anti-inflammatory effects clinically. Drug Dev Res 77 : 206-211, 2016. © 2016 The Authors Drug Development Research Published by Wiley Periodicals, Inc. © 2016 The Authors Drug Development Research Published by Wiley Periodicals, Inc.

Topical Anti‐Inflammatory and Analgesic Effects of Multiple Applications of S(+)‐Flurbiprofen Plaster (SFPP) in a Rat Adjuvant‐Induced Arthritis Model

PubMed Central

Toda, Yoshihisa; Hori, Miyuki; Mitani, Akiko; Ichihara, Takahiro; Sekine, Shingo; Kaku, Shinsuke; Otsuka, Noboru; Matsumoto, Hideo

2016-01-01

Abstract Preclinical Research The aim of this study was to evaluate the efficacy of multiple applications of S(+)‐flurbiprofen plaster (SFPP), a novel Nonsteroidal anti‐inflammatory drug (NSAID) patch, for the alleviation of inflammatory pain and edema in rat adjuvant‐induced arthritis (AIA) model as compared to other NSAID patches. The AIA model was induced by the injection of Mycobacterium butyricum and rats were treated with a patch (1.0 cm × 0.88 cm) containing each NSAID (SFP, ketoprofen, loxoprofen, diclofenac, felbinac, flurbiprofen, or indomethacin) applied to the paw for 6 h per day for 5 days. The pain threshold was evaluated using a flexion test of the ankle joint, and the inflamed paw edema was evaluated using a plethysmometer. cyclooxygenase (COX)−1 and COX‐2 inhibition was evaluated using human recombinant proteins. Multiple applications of SFPP exerted a significant analgesic effect from the first day of application as compared to the other NSAID patches. In terms of paw edema, SFPP decreased edema from the second day after application, Multiple applications of SFPP were superior to those of other NSAID patches, in terms of the analgesic effect with multiple applications. These results suggest that SFPP may be a beneficial patch for providing analgesic and anti‐inflammatory effects clinically. Drug Dev Res 77 : 206–211, 2016. © 2016 The Authors Drug Development Research Published by Wiley Periodicals, Inc. PMID:27241582

Physico-chemical characterization of mortars as a tool in studying specific hydraulic components: application to the study of ancient Naxos aqueduct

NASA Astrophysics Data System (ADS)

Maravelaki-Kalaitzaki, P.; Galanos, A.; Doganis, I.; Kallithrakas-Kontos, N.

2011-07-01

Mortars and plasters from the ancient aqueduct on the island of Naxos, Greece, were studied with regard to mineralogical and chemical composition, grain size distribution, raw materials and hydraulic properties, in order to assess their characteristics and design compatible repair mortars. The authentic materials contained lime, crushed-brick, siliceous and calcitic aggregates, in different proportions according to mortar type. Crushed-bricks fired at low temperatures and lightweight volcanic aggregates contained amorphous phases, which upon reaction with lime yielded hydraulic components capable of protecting the construction from the continuous presence of water. Hydraulic calcium silicate/aluminate hydrates, the proportions and the perfect packing of the raw materials, along with the diligent application justify the longevity and durability of the studied samples. The hydraulic properties of samples were pointed out through (a) the well-established CO2/H2O ratio derived from the thermogravimetric analysis and (b) by introducing two powerful indices issued from the chemical analysis, namely CaOhydr and soluble SiO2 hydr. These indices improved the clustering of hydraulic mortars and provided better correlation between mortars, plasters and their binders. By comparing grain size distribution and hydraulicity indices it was possible to distinguish among the construction phases. Based on this study, repair mortars were formulated by hydraulic lime, siliceous sand, calcareous and crushed-brick aggregates, with the optimal water content, ensuring optimum workability and compatible appearance with the authentic ones.

Workplace Respiratory Protection Factors during Asbestos Removal Operations.

PubMed

Chazelet, Sandrine; Wild, Pascal; Silvente, Eric; Eypert-Blaison, Céline

2018-05-28

Numerous changes have been made to the French labour regulations in recent years relating to the prevention of risks of exposure to asbestos fibres for operators removing asbestos-containing materials. These changes refer to the method used to count fibres, the collective and personal protective devices to be used on these worksites, and the occupational exposure limit value, which was reduced to 10 f.L-1 on 2 July 2015. In this context, this study assessed the level of respiratory protection afforded by supplied-air respirators and powered air-purifying respirators by monitoring exposure for several operators on nine worksites. The levels of dustiness measured in personal samples taken outside masks showed significant evidence of potential exposure during removal of asbestos-containing plaster or sprayed asbestos, and when using abrasive blasting to treat asbestos-containing materials. For these tasks outside concentration regularly exceeds 25000 f.L-1. Measurements inside masks were generally low, under 10 f.L-1, except in some situations involving the removal of asbestos-containing plaster. This partial penetration of fibres inside masks could be due to the high loading linked to this material. The distributions of Workplace Protection Factors obtained for the two types of respiratory protective devices studied were broad, and the fifth percentile values equal to 236 and 104, respectively, for supplied-air respirators and powered air-purifying respirators. This work highlights once again the need to prioritize collective protection when seeking to prevent asbestos-related risks.

Venous Thrombosis Risk after Cast Immobilization of the Lower Extremity: Derivation and Validation of a Clinical Prediction Score, L-TRiP(cast), in Three Population-Based Case–Control Studies

PubMed Central

Nemeth, Banne; van Adrichem, Raymond A.; van Hylckama Vlieg, Astrid; Bucciarelli, Paolo; Martinelli, Ida; Baglin, Trevor; Rosendaal, Frits R.; le Cessie, Saskia; Cannegieter, Suzanne C.

2015-01-01

Background Guidelines and clinical practice vary considerably with respect to thrombosis prophylaxis during plaster cast immobilization of the lower extremity. Identifying patients at high risk for the development of venous thromboembolism (VTE) would provide a basis for considering individual thromboprophylaxis use and planning treatment studies. The aims of this study were (1) to investigate the predictive value of genetic and environmental risk factors, levels of coagulation factors, and other biomarkers for the occurrence of VTE after cast immobilization of the lower extremity and (2) to develop a clinical prediction tool for the prediction of VTE in plaster cast patients. Methods and Findings We used data from a large population-based case–control study (MEGA study, 4,446 cases with VTE, 6,118 controls without) designed to identify risk factors for a first VTE. Cases were recruited from six anticoagulation clinics in the Netherlands between 1999 and 2004; controls were their partners or individuals identified via random digit dialing. Identification of predictor variables to be included in the model was based on reported associations in the literature or on a relative risk (odds ratio) > 1.2 and p ≤ 0.25 in the univariate analysis of all participants. Using multivariate logistic regression, a full prediction model was created. In addition to the full model (all variables), a restricted model (minimum number of predictors with a maximum predictive value) and a clinical model (environmental risk factors only, no blood draw or assays required) were created. To determine the discriminatory power in patients with cast immobilization (n = 230), the area under the curve (AUC) was calculated by means of a receiver operating characteristic. Validation was performed in two other case–control studies of the etiology of VTE: (1) the THE-VTE study, a two-center, population-based case–control study (conducted in Leiden, the Netherlands, and Cambridge, United Kingdom) with 784 cases and 523 controls included between March 2003 and December 2008 and (2) the Milan study, a population-based case–control study with 2,117 cases and 2,088 controls selected between December 1993 and December 2010 at the Thrombosis Center, Fondazione IRCCS Ca’ Granda–Ospedale Maggiore Policlinico, Milan, Italy. The full model consisted of 32 predictors, including three genetic factors and six biomarkers. For this model, an AUC of 0.85 (95% CI 0.77–0.92) was found in individuals with plaster cast immobilization of the lower extremity. The AUC for the restricted model (containing 11 predictors, including two genetic factors and one biomarker) was 0.84 (95% CI 0.77–0.92). The clinical model (consisting of 14 environmental predictors) resulted in an AUC of 0.77 (95% CI 0.66–0.87). The clinical model was converted into a risk score, the L-TRiP(cast) score (Leiden–Thrombosis Risk Prediction for patients with cast immobilization score), which showed an AUC of 0.76 (95% CI 0.66–0.86). Validation in the THE-VTE study data resulted in an AUC of 0.77 (95% CI 0.58–0.96) for the L-TRiP(cast) score. Validation in the Milan study resulted in an AUC of 0.93 (95% CI 0.86–1.00) for the full model, an AUC of 0.92 (95% CI 0.76–0.87) for the restricted model, and an AUC of 0.96 (95% CI 0.92–0.99) for the clinical model. The L-TRiP(cast) score resulted in an AUC of 0.95 (95% CI 0.91–0.99). Major limitations of this study were that information on thromboprophylaxis was not available for patients who had plaster cast immobilization of the lower extremity and that blood was drawn 3 mo after the thrombotic event. Conclusions These results show that information on environmental risk factors, coagulation factors, and genetic determinants in patients with plaster casts leads to high accuracy in the prediction of VTE risk. In daily practice, the clinical model may be the preferred model as its factors are most easy to determine, while the model still has good predictive performance. These results may provide guidance for thromboprophylaxis and form the basis for a management study. PMID:26554832

Overjet and overbite analysis during the eruption of the upper permanent incisors.

PubMed

Cuoghi, Osmar A; Sella, Rodrigo C; Mamede, Igo; de Macedo, Fernanda A; Miranda-Zamalloa, Yésselin M; de Mendonça, Marcos R

2009-01-01

ABSTRACT The purpose of this study was to analyze the overjet and overbite behavior during eruption of the upper permanent incisors. Fourth-eight plaster casts of 16 patients from ages 6-13 years were appraised longitudinally. It was found that the overjet remains constant, starting at the eruption of the upper permanent central incisors until eruption of the upper permanent canine teeth, while the overbite increases after eruption of the upper permanent lateral incisors and remains constant with the eruption of the canine teeth.

The impact of the fabrication method on the three-dimensional accuracy of an implant surgery template.

PubMed

Matta, Ragai-Edward; Bergauer, Bastian; Adler, Werner; Wichmann, Manfred; Nickenig, Hans-Joachim

2017-06-01

The use of a surgical template is a well-established method in advanced implantology. In addition to conventional fabrication, computer-aided design and computer-aided manufacturing (CAD/CAM) work-flow provides an opportunity to engineer implant drilling templates via a three-dimensional printer. In order to transfer the virtual planning to the oral situation, a highly accurate surgical guide is needed. The aim of this study was to evaluate the impact of the fabrication method on the three-dimensional accuracy. The same virtual planning based on a scanned plaster model was used to fabricate a conventional thermo-formed and a three-dimensional printed surgical guide for each of 13 patients (single tooth implants). Both templates were acquired individually on the respective plaster model using an optical industrial white-light scanner (ATOS II, GOM mbh, Braunschweig, Germany), and the virtual datasets were superimposed. Using the three-dimensional geometry of the implant sleeve, the deviation between both surgical guides was evaluated. The mean discrepancy of the angle was 3.479° (standard deviation, 1.904°) based on data from 13 patients. Concerning the three-dimensional position of the implant sleeve, the highest deviation was in the Z-axis at 0.594 mm. The mean deviation of the Euclidian distance, dxyz, was 0.864 mm. Although the two different fabrication methods delivered statistically significantly different templates, the deviations ranged within a decimillimeter span. Both methods are appropriate for clinical use. Copyright © 2017 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Reproduction accuracy of articulator mounting with an arbitrary face-bow vs. average values-a controlled, randomized, blinded patient simulator study.

PubMed

Ahlers, M Oliver; Edelhoff, Daniel; Jakstat, Holger A

2018-06-21

The benefit from positioning the maxillary casts with the aid of face-bows has been questioned in the past. Therefore, the aim of this study was to investigate the reliability and validity of arbitrary face-bow transfers compared to a process solely based on the orientation by means of average values. For optimized validity, the study was conducted using a controlled, randomized, anonymized, and blinded patient simulator study design. Thirty-eight undergraduate dental students were randomly divided into two groups; both groups were applied to both methods, in opposite sequences. Investigated methods were the transfer of casts using an arbitrary face-bow in comparison to the transfer using average values based on Bonwill's triangle and the Balkwill angle. The "patient" used in this study was a patient simulator. All casts were transferred to the same individual articulator, and all the transferred casts were made using type IV special hard stone plaster; for the attachment into the articulator, type II plaster was used. A blinded evaluation was performed based on three-dimensional measurements of three reference points. The results are presented three-dimensionally in scatterplots. Statistical analysis indicated a significantly smaller variance (Student's t test, p < 0.05) for the transfer using a face-bow, applicable for all three reference points. The use of an arbitrary face-bow significantly improves the transfer reliability and hence the validity. To simulate the patient situation in an individual articulator correctly, casts should be transferred at least by means of an arbitrary face-bow.

Comparison of the marginal fit of milled yttrium stabilized zirconium dioxide crowns obtained by scanning silicone impressions and by scanning stone replicas.

PubMed

Aranda Yus, Estefanía; Cantarell, Josep Maria Anglada; Miñarro Alonso, Antonio

2018-06-01

To determine the discrepancy in monolithic zirconium dioxide crowns made with computer-aided design and computer-aided manufacturing (CAD/CAM) systems by comparing scans of silicone impressions and of master casts. From a Cr-Co master die of a first upper left molar, 30 silicone impressions were taken. The 30 silicone impressions were scanned with the laboratory scanner, thus obtaining 30 milled monolithic yttrium stabilized zirconium dioxide (YSZD) crowns (the silicone group). They were poured and the working models were scanned, obtaining 30 milled monolithic yttrium stabilized zirconium dioxide (YSZD) crowns (the plaster group). Three predetermined points were analyzed in each side of the crown (Mesial, Distal ,Vestibular and Palatal), and the marginal fit was evaluated with SEM (×600). The response variable is the discrepancy from the master model. A repeated measures ANOVA with two within subject factors was performed to study significance of main factors and interaction. Mean marginal discrepancy was 22.42±35.65 µm in the silicone group and 8.94±14.69 µm in the plaster group. The statistical analysis showed significant differences between the two groups and also among the four aspects. Interaction was also significant ( P =.02). The mean marginal fit values of the two groups were within the clinically acceptable values. Significant differences were found between the groups according to the aspects studied. Various factors influenced the accuracy of digitizing, such as the design, the geometry, and the preparation guidance, as well as the texture, roughness and the color of the scanned material.

A new method to quantify liner deformation within a prosthetic socket for below knee amputees.

PubMed

Lenz, Amy L; Johnson, Katie A; Bush, Tamara Reid

2018-06-06

Many amputees who wear a leg prosthesis develop significant skin wounds on their residual limb. The exact cause of these wounds is unclear as little work has studied the interface between the prosthetic device and user. Our research objective was to develop a quantitative method for assessing displacement patterns of the gel liner during walking for patients with transtibial amputation. Using a reflective marker system and a custom clear socket, evaluations were conducted with a clear transparent test socket mounted over a plaster limb model and a deformable limb model. Distances between markers placed on the limb were measured with a digital caliper and then compared with data from the motion capture system. Additionally, the rigid plaster set-up was moved in the capture volume to simulate walking and evaluate if inter-marker distances changed in comparison to static data. Dynamic displacement trials were then collected to measure changes in inter-marker distance due to vertical elongation of the gel liner. Static and dynamic inter-marker distances within day and across days confirmed the ability to accurately capture displacements using this new approach. These results encourage this novel method to be applied to a sample of amputee patients during walking to assess displacements and the distribution of the liner deformation within the socket. The ability to capture changes in deformation of the gel liner will provide new data that will enable clinicians and researchers to improve design and fit of the prosthesis so the incidence of pressure ulcers can be reduced. Copyright © 2018 Elsevier Ltd. All rights reserved.

Influence of environment factors on humidity conditions of selected external wall solutions in a heated building

NASA Astrophysics Data System (ADS)

Kaczmarek, Anna

2017-10-01

Contemporary single-family houses in Poland are often built during 3 quarters of a year (spring to autumn) are usually settled in a winter season. It is a special case when exploitation humidity coincides with technological one, causing unfavourable humidity conditions during the first years of exploitation. In consequence, thermal parameters of partitions differ from those assumed in the project. In construction stage the humidity state of a wall stabilizes as a result of water: associated with storage, entered technologically during wall construction and plastering, coming from rainfall. Thermo-insulation materials are built-in at dry state. During erection and exploitation of a building their thermal conductivity is changing depending on humidity conditions. According to building rules, construction humidity should be removed from a partition before the building transfer to usage, because it lowers the thermal partition insulation ability and increases air humidity of building interior. Walls are plastered and insulated in condition of simultaneous presence of atmospheric and technological humidity which cause special humidity condition during first years of exploitation. As a consequence, heating costs are substantially higher. In this article the results of simulation are shown performed with WUFI ®PRO 5 software, which was intended to define the time necessary for reaching the stabilised humidity in selected solutions of two-layer walls applied in a heated building. In the research performed, the partition orientation along geographic directions, short and long wave radiation, and environment humidity (air humidity, driving rain) coincidence with technological humidity in assumed wall solutions were taken into account.

Importance of Tensile Strength on the Shear Behavior of Discontinuities

NASA Astrophysics Data System (ADS)

Ghazvinian, A. H.; Azinfar, M. J.; Geranmayeh Vaneghi, R.

2012-05-01

In this study, the shear behavior of discontinuities possessing two different rock wall types with distinct separate compressive strengths was investigated. The designed profiles consisted of regular artificial joints molded by five types of plaster mortars, each representing a distinct uniaxial compressive strength. The compressive strengths of plaster specimens ranged from 5.9 to 19.5 MPa. These specimens were molded considering a regular triangular asperity profile and were designed so as to achieve joint walls with different strength material combinations. The results showed that the shear behavior of discontinuities possessing different joint wall compressive strengths (DDJCS) tested under constant normal load (CNL) conditions is the same as those possessing identical joint wall strengths, but the shear strength of DDJCS is governed by minor joint wall compressive strength. In addition, it was measured that the predicted values obtained by Barton's empirical criterion are greater than the experimental results. The finding indicates that there is a correlation between the joint roughness coefficient (JRC), normal stress, and mechanical strength. It was observed that the mode of failure of asperities is either pure tensile, pure shear, or a combination of both. Therefore, Barton's strength criterion, which considers the compressive strength of joint walls, was modified by substituting the compressive strength with the tensile strength. The validity of the modified criterion was examined by the comparison of the predicted shear values with the laboratory shear test results reported by Grasselli (Ph.D. thesis n.2404, Civil Engineering Department, EPFL, Lausanne, Switzerland, 2001). These comparisons infer that the modified criterion can predict the shear strength of joints more precisely.

Approach to intraoperative electromagnetic navigation in orthognathic surgery: A phantom skull based trial.

PubMed

Berger, Moritz; Kallus, Sebastian; Nova, Igor; Ristow, Oliver; Eisenmann, Urs; Dickhaus, Hartmut; Kuhle, Reinald; Hoffmann, Jürgen; Seeberger, Robin

2015-11-01

Intraoperative guidance using electromagnetic navigation is an upcoming method in maxillofacial surgery. However, due to their unwieldy structures, especially the line-of-sight problem, optical navigation devices are not used for daily orthognathic surgery. Therefore, orthognathic surgery was simulated on study phantom skulls, evaluating the accuracy and handling of a new electromagnetic tracking system. Le-Fort I osteotomies were performed on 10 plastic skulls. Orthognathic surgical planning was done in the conventional way using plaster models. Accuracy of the gold standard, splint-based model surgery versus an electromagnetic tracking system was evaluated by measuring the actual maxillary deviation using bimaxillary splints and preoperative and postoperative cone beam computer tomography imaging. The distance of five anatomical marker points were compared pre- and postoperatively. The electromagnetic tracking system was significantly more accurate in all measured parameters compared with the gold standard using bimaxillary splints (p < 0.01). The data shows a discrepancy between the model surgical plans and the actual correction of the upper jaw of 0.8 mm. Using the electromagnetic tracking, we could reduce the discrepancy of the maxillary transposition between the planned and actual orthognathic surgery to 0.3 mm on average. The data of this preliminary study shows a high level of accuracy in surgical orthognathic performance using electromagnetic navigation, and may offer greater precision than the conventional plaster model surgery with bimaxillary splints. This preliminary work shows great potential for the establishment of an intraoperative electromagnetic navigation system for maxillofacial surgery. Copyright © 2015 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

The Long-Term Safety of S-Flurbiprofen Plaster for Osteoarthritis Patients: An Open-Label, 52-Week Study.

PubMed

Yataba, Ikuko; Otsuka, Noboru; Matsushita, Isao; Matsumoto, Hideo; Hoshino, Yuichi

2016-08-01

The newly developed S-flurbiprofen plaster (SFPP) is a tape-type patch that shows innovative percutaneous absorption. This study was designed to evaluate the safety of a long-term 52-week SFPP application to osteoarthritis (OA) patients. This was a multi-center, open-label, uncontrolled prospective study that included 201 OA patients. SFPP at 40 mg/day was applied to the site of pain in 101 patients and at 80 mg/day (2 patches) in 100 patients at a total of 301 sites for 52 weeks. The affected sites assessed included the knee (192), lumbar spine (66), cervical spine (26), and others (17). Drug safety was evaluated by medical examination, laboratory tests, and examination of vital signs. Efficacy was evaluated by the patient's and clinician's global assessments and clinical symptoms. Most patients (80.1 %) completed the 52-week SFPP application. The majority of drug-related adverse events (AEs) included mild dermatitis at the application sites and occurred in 46.8 % of the sites. No photosensitive dermatitis was observed. Systemic AEs occurred in 9.0 % of the patients; a serious AE (gastric ulcer hemorrhage) occurred in one patient. No clinically significant changes in the laboratory tests and vital signs were observed. The efficacy evaluation showed an improvement from 2 weeks after the SFPP application, which continued during the 52 weeks' treatment. No apparent safety concerns were observed, even during the long-term SFPP application. Therefore, SFPP could be an additional pharmacotherapy in OA treatment.

Analgesic Effect of the Newly Developed S(+)-Flurbiprofen Plaster on Inflammatory Pain in a Rat Adjuvant-Induced Arthritis Model.

PubMed

Sugimoto, Masanori; Toda, Yoshihisa; Hori, Miyuki; Mitani, Akiko; Ichihara, Takahiro; Sekine, Shingo; Hirose, Takuya; Endo, Hiromi; Futaki, Nobuko; Kaku, Shinsuke; Otsuka, Noboru; Matsumoto, Hideo

2016-02-01

Preclinical Research This article describes the properties of a novel topical NSAID (Nonsteroidal anti-inflammatory drug) patch, SFPP (S(+)-flurbiprofen plaster), containing the potent cyclooxygenase (COX) inhibitor, S(+)-flurbiprofen (SFP). The present studies were conducted to confirm human COX inhibition and absorption of SFP and to evaluate the analgesic efficacy of SFPP in a rat adjuvant-induced arthritis (AIA) model. COX inhibition by SFP, ketoprofen and loxoprofen was evaluated using human recombinant COX proteins. Absorption of SFPP, ketoprofen and loxoprofen from patches through rat skin was assessed 24 h after application. The AIA model was induced by injecting Mycobacterium tuberculosis followed 20 days later by the evaluation of the prostaglandin PGE2 content of the inflamed paw and the pain threshold. SFP exhibited more potent inhibitory activity against COX-1 (IC50  = 8.97 nM) and COX-2 (IC50  = 2.94 nM) than the other NSAIDs evaluated. Absorption of SFP was 92.9%, greater than that of ketoprofen and loxoprofen from their respective patches. Application of SFPP decreased PGE2 content from 15 min to 6 h and reduced paw hyperalgesia compared with the control, ketoprofen and loxoprofen patches. SFPP showed analgesic efficacy, and was superior to the ketoprofen and loxoprofen patches, which could be through the potent COX inhibitory activity of SFP and greater skin absorption. The results suggested SFPP can be expected to exert analgesic effect clinically. © 2016 The Authors Drug Development Research Published by Wiley Periodicals, Inc.

Analgesic Effect of the Newly Developed S(+)‐Flurbiprofen Plaster on Inflammatory Pain in a Rat Adjuvant‐Induced Arthritis Model

PubMed Central

Toda, Yoshihisa; Hori, Miyuki; Mitani, Akiko; Ichihara, Takahiro; Sekine, Shingo; Hirose, Takuya; Endo, Hiromi; Futaki, Nobuko; Kaku, Shinsuke; Otsuka, Noboru; Matsumoto, Hideo

2016-01-01

ABSTRACT Preclinical Research This article describes the properties of a novel topical NSAID (Nonsteroidal anti‐inflammatory drug) patch, SFPP (S(+)‐flurbiprofen plaster), containing the potent cyclooxygenase (COX) inhibitor, S(+)‐flurbiprofen (SFP). The present studies were conducted to confirm human COX inhibition and absorption of SFP and to evaluate the analgesic efficacy of SFPP in a rat adjuvant‐induced arthritis (AIA) model. COX inhibition by SFP, ketoprofen and loxoprofen was evaluated using human recombinant COX proteins. Absorption of SFPP, ketoprofen and loxoprofen from patches through rat skin was assessed 24 h after application. The AIA model was induced by injecting Mycobacterium tuberculosis followed 20 days later by the evaluation of the prostaglandin PGE2 content of the inflamed paw and the pain threshold. SFP exhibited more potent inhibitory activity against COX‐1 (IC50 = 8.97 nM) and COX‐2 (IC50 = 2.94 nM) than the other NSAIDs evaluated. Absorption of SFP was 92.9%, greater than that of ketoprofen and loxoprofen from their respective patches. Application of SFPP decreased PGE2 content from 15 min to 6 h and reduced paw hyperalgesia compared with the control, ketoprofen and loxoprofen patches. SFPP showed analgesic efficacy, and was superior to the ketoprofen and loxoprofen patches, which could be through the potent COX inhibitory activity of SFP and greater skin absorption. The results suggested SFPP can be expected to exert analgesic effect clinically. Drug Dev Res 76 : 20–28, 2016. © 2016 Wiley Periodicals, Inc. PMID:26763139

Localized neuropathic pain: an expert consensus on local treatments

PubMed Central

Pickering, Gisèle; Martin, Elodie; Tiberghien, Florence; Delorme, Claire; Mick, Gérard

2017-01-01

Background Pain localization is one of the hallmarks for the choice of first-line treatment in neuropathic pain. This literature review has been conducted to provide an overview of the current knowledge regarding the etiology and pathophysiology of localized neuropathic pain (LNP), its assessment and the existing topical pharmacological treatments. Materials and methods Literature review was performed using Medline from 2010 to December 2016, and all studies involving LNP and treatments were examined. A multidisciplinary expert panel of five pain specialists in this article reports a consensus on topical approaches that may be recommended to alleviate LNP and on their advantages in clinical practice. Results Successive international recommendations have included topical 5% lidocaine and 8% capsaicin for LNP treatment. The expert panel considers that these compounds can be a first-line treatment for LNP, especially in elderly patients and patients with comorbidities and polypharmacy. Regulatory LNP indications should cover the whole range of LNP and not be restricted to specific etiologies or sites. Precautions for the use of plasters must be followed cautiously. Conclusion Although there is a real need for more randomized controlled trials for both drugs, publications clearly demonstrate excellent risk/benefit ratios, safety, tolerance and continued efficacy throughout long-term treatment. A major advantage of both plasters is that they have proven efficacy and may reduce the risk of adverse events such as cognitive impairment, confusion, somnolence, dizziness and constipation that are often associated with systemic neuropathic pain treatment and reduce the quality of life. Topical modalities also may be used in combination with other drugs and analgesics with limited drug–drug interactions. PMID:29066862

[Effectiveness of the transparent sterile dressing vs standard to fix the peripheral venous catheter (PVC) on the incidence of phlebitis. A randomized controlled trial].

PubMed

Forni, Cristiana; D'Alessandro, Fabio; Gambino, Orazio; Amodeo, Alfredo; Pignotti, Elettra; Zanotti, Enrichetta; Tremosini, Morena; Trofa, Carmela; Sabattini, Tania; Matino, Federica; Genco, Rossana; Schiavone, Miguel; Bombino, Caterina; Mini, Sandra; Rocchegiani, Laura; Notarnicola, Teresa; Capezzali, Daniela; Boschi, Rita; Loro, Loretta

2012-01-01

Effectiveness of the transparent sterile dressing vs standard to fix the peripheral venous catheter (PVC), on the incidence of phlebitis. A randomized controlled trial. The type of dressing could contribute to the incidence of phlebitis, infiltration and accidental removals but the results of the studies are contrasting and samples are limited. To compare the effectiveness of a transparent polyurethane sterile dressing on the rate of phlebitis associated to peripheral venous catheter (PVC) vs a non sterile sticking plaster in use in current practice (standard dressing). Randomized controlled trial. Participants. 1061 PVCs (703 patients, adults and children) at a research orthopedic hospital in the north of Italy; 540 PVCs allocated to receive the sterile and 521 the standard dressing. 96 PVCs were excluded for phlebitis, 48 (9.6%) in the sterile and 48 (10.1%) in the standard dressing group, RR 0.96 (95%CI 0.697 - 1.335). Accidental removal of the PVCs was more frequent with the sterile dressing (9.6% vs 6.3%) but the number of catheters removed without complications was larger in the standard dressing group (48.9% vs 54.9% P=0.0503). Eighty-five PVCs were replaced for detachment of the dressing (50, 9.2% sterile and 35, 6.7% standard dressing). The cheapest transparent sterile dressing costs 32 cents while the standard 9 cents. A sticking non sterile plasters is not influential on the rate of phlebitis and ensures an good fix of the PVC compared the transparent sterile dressing to of polyurethane film.

Using stereophotogrammetric technology for obtaining intraoral digital impressions of implants.

PubMed

Pradíes, Guillermo; Ferreiroa, Alberto; Özcan, Mutlu; Giménez, Beatriz; Martínez-Rus, Francisco

2014-04-01

The procedure for making impressions of multiple implants continues to be a challenge, despite the various techniques proposed to date. The authors' objective in this case report is to describe a novel digital impression method for multiple implants involving the use of stereophotogrammetric technology. The authors present three cases of patients who had multiple implants in which the impressions were obtained with this technology. Initially, a stereo camera with an infrared flash detects the position of special flag abutments screwed into the implants. This process is based on registering the x, y and z coordinates of each implant and the distances between them. This information is converted into a stereolithographic (STL) file. To add the soft-tissue information, the user must obtain another STL file by using an intraoral or extraoral scanner. In the first case presented, this information was acquired from the plaster model with an extraoral scanner; in the second case, from a Digital Imaging and Communication in Medicine (DICOM) file of the plaster model obtained with cone-beam computed tomography; and in the third case, through an intraoral digital impression with a confocal scanner. In the three cases, the frameworks manufactured from this technique showed a correct clinical passive fit. At follow-up appointments held six, 12 and 24 months after insertion of the prosthesis, no complications were reported. Stereophotogrammetric technology is a viable, accurate and easy technique for making multiple implant impressions. Clinicians can use stereophotogrammetric technology to acquire reliable digital master models as a first step in producing frameworks with a correct passive fit.

Acute antibody-directed myostatin inhibition attenuates disuse muscle atrophy and weakness in mice.

PubMed

Murphy, Kate T; Cobani, Vera; Ryall, James G; Ibebunjo, Chikwendu; Lynch, Gordon S

2011-04-01

Counteracting the atrophy of skeletal muscle associated with disuse has significant implications for minimizing the wasting and weakness in plaster casting, joint immobilization, and other forms of limb unloading, with relevance to orthopedics, sports medicine, and plastic and reconstructive surgery. We tested the hypothesis that antibody-directed myostatin inhibition would attenuate the loss of muscle mass and functional capacity in mice during 14 or 21 days of unilateral hindlimb casting. Twelve-week-old C57BL/10 mice were subjected to unilateral hindlimb plaster casting or served as controls. Mice received subcutaneous injections of saline or a mouse chimera of anti-human myostatin antibody (PF-354, 10 mg/kg; n = 6-9) on days 0 and 7 and were tested for muscle function on day 14, or were treated on days 0, 7, and 14 and tested for muscle function on day 21. Hindlimb casting reduced muscle mass, fiber size, and function of isolated soleus and extensor digitorum longus (EDL) muscles (P < 0.05). PF-354 attenuated the loss of muscle mass, fiber size, and function with greater effects after 14 days than after 21 days of casting, when wasting and weakness had plateaued (P < 0.05). Antibody-directed myostatin inhibition therefore attenuated the atrophy and loss of functional capacity in muscles from mice subjected to unilateral hindlimb casting with reductions in muscle size and strength being most apparent during the first 14 days of disuse. These findings highlight the therapeutic potential of antibody-directed myostatin inhibition for disuse atrophy especially within the first 2 wk of disuse.

New method for mass transfer across the surface of non-spherical particles in turbulence

NASA Astrophysics Data System (ADS)

Oehmke, T.; Variano, E. A.

2016-12-01

We present a method for making model particles that allow for the interfacial mass transfer rate to be measured. This is similar to traditional use of gypsum plaster used to measure erosion rates on the timescale of weeks to years. Our new method is useful for measuring erosion rates on the timescale of minutes. We use this to measure the manner in which particle shape affects its rate of dissolution in turbulent flow. The related questions are relevant to mass transfer in turbulence, e.g. in cases of marine biology and pollution by microplastics.

Intramedullary Percutaneous Fixation of Extra-Articular Proximal and Middle Phalanx Fractures.

PubMed

Jovanovic, Nebojsa; Aldlyami, Ehab; Saraj, Basem; Fm Seidam, Mohamed; Badawi, Hamed; Shaat, Ahmed; Alawadi, Khalid; Dodakundi, Chaitanya

2018-06-01

Multiple methods have been described for treating unstable proximal and middle phalangeal fractures. Irrespective of using an open or closed technique of fixation, stiffness and extensor lag at the proximal/distal interphalangeal joint almost always occur. This issue can be avoided by allowing the patients to mobilize the fingers out of plaster or splint as early as possible from the day of surgery. We describe a technique of intramedullary percutaneous fixation of extra-articular proximal and middle phalanx fractures allowing immediate mobilization of fingers, concurrent stabilization with progressive healing and thus preventing such complications.

8. Several of the rental rooms are joined by doors, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. Several of the rental rooms are joined by doors, and each room is accessed from the corridor. Originally, the transoms were glazed. When a central heating/cooling system was installed, the transoms were modified to accommodate air grilles that are supplied by a duct located in the corridor. The five-panel door and wood wainscot are original features. However, the wainscot does not occur in every room. The lath and plaster partitions and the wood flooring are typical of the original construction. Credit GADA/MRM. - Stroud Building, 31-33 North Central Avenue, Phoenix, Maricopa County, AZ

[Application of stereoscopy on edible birds nest identification].

PubMed

Lin, Jie-Ru; Zhou, Hua; Lai, Xiao-Ping

2006-03-01

To study the feasibility of using stereoscopy in identification on Edible Bird's Nest (EBN). Characteristics of white EBN pieces, red EBN, white fungus pieces and EBN painted with colloid were observed under stereoscopy. EBN pieces could be distinguished from white fungus pieces under stereoscope. The former is semitransparent and has more fine cracks; the latter is opaque and without fine cracks. EBN painted with colloid can be distinguished under stereoscopy too. The characteristics include: (1) the surface lines were not clear; (2) feathers were plastered on the surface. Stereoscopy can be used in identification of EBN, especially in general investigation of commercials.

Desalination of brick masonry and stone carvings in Capitullum hall of Riga Dome Cathedral

NASA Astrophysics Data System (ADS)

Grave, J.; Krage, L.; Lusis, R.; Vitina, I.

2011-12-01

The construction of Riga Dome Cathedral and its Capithullum hall were initiated in 1211. Through centuries they were damaged a lot due to migration of soluble salts and moisture. During the last restoration (1888-1891) a lot of mistakes were conceded and subsequently some of probable solutions for restoration were unsuccessful. In 2009 the new restoration stage in Capithullum hall was started. Two types of desalination methods were used in hall - desalination with lime-sand plaster and poultice of lignin. Both quantitative and semiquantitative chemical analyses were performed in order to appreciate the desalination process.

Time evolution of pore system in lime - Pozzolana composites

NASA Astrophysics Data System (ADS)

Doleželová, Magdaléna; Čáchová, Monika; Scheinherrová, Lenka; Keppert, Martin

2017-11-01

The lime - pozzolana mortars and plasters are used in restoration works on building cultural heritage but these materials are also following the trend of energy - efficient solutions in civil engineering. Porosity and pore size distribution is one of crucial parameters influencing engineering properties of porous materials. The pore size distribution of lime based system is changing in time due to chemical processes occurring in the material. The present paper describes time evolution of pore system in lime - pozzolana composites; the obtained results are useful in prediction of performance of lime - pozzolana systems in building structures.

[Development of Terahertz Imaging Technology in the Assessment of Burn Injuries].

PubMed

Zhu, Xinjian; He, Xuan; Wang, Pin; Gao, Dandan; Qiu, Yan; He, Qinghua; Wu, Baoming

2016-02-01

Terahertz waves have unique properties and advantages, which makes it gain increasing attention and applications in the biomedical field. Burns is a common clinical trauma. Since the water-sensitive and non-destructive characteristics of terahertz, terahertz imaging techniques can be used to detect burns. So far, terahertz imaging technology in the assessment of burn injuries has been developed from ex vivo to in vivo, and high-resolution images can be obtained through the gauzes and plasters. In this paper, we mainly introduces the application of terahertz imaging technology and development in the assessment of burn injuries.

Skin thickness effects on in vivo LXRF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Preiss, I.L.; Washington, W. II

The analysis of lead concentration in bone utilizing LXRF can be adversely effected by overlying issue. A quantitative measure of the attenuation of the 10.5 keV Pb L a x-ray signal by skin and skin equivalent plastic has been conducted. Concentration ranges in plaster of Paris and goat bone from 7 to 90 ppm with attenuators of Lucite{reg_sign} and pig skin were examined. It is concluded that no quantitative or semi quantitative analysis can be achieved if overlying sue thickness exceeds 3 mm for Ph concentrations of less than 30 porn Ph in bone.

12. Photocopy of photograph (original color slide made in 1974 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. Photocopy of photograph (original color slide made in 1974 by Henry D. Boykin, II, A.I.A., of Camden, South Carolina, and kept in his possession) FULL SECTIONAL VIEW OF SOUTH WALL OF NAVE SHOWING TYPICAL INTERNAL CONSTRUCTION AND MATERIALS OF CHURCH WALLS. BRICK BUTTRESS WITH CREPE COVERING ON LEFT; RAMMED EARTH WALL CORE IN CENTER (ADZE MARKS ARE FROM 1974 REPAIR PROCESS); INTERIOR LATH, PLASTER, AND CORNICE ON RIGHT. NOTE REMAINS OF EMBEDDED WOODEN BRACES (NEAR BUTTRESS) USED TO HOLD WALL FORMS DURING ORIGINAL CONSTRUCTION OF WALLS. - Church of the Holy Cross, State Route 261, Stateburg, Sumter County, SC

Methods for Casting Subterranean Ant Nests

PubMed Central

Tschinkel, Walter R.

2010-01-01

The study of subterranean ant nests has been impeded by the difficulty of rendering their structures in visible form. Here, several different casting materials are shown to make perfect casts of the underground nests of ants. Each material (dental plaster, paraffin wax, aluminum, zinc) has advantages and limitations, which are discussed. Some of the materials allow the recovery of the ants entombed in the casts, allowing a census of the ants to be connected with features of their nest architecture. The necessary equipment and procedures are described in the hope that more researchers will study this very important aspect of ant natural history. PMID:20673073

Occupational therapy and Colles' fractures.

PubMed

Christensen, O M; Kunov, A; Hansen, F F; Christiansen, T C; Krasheninnikoff, M

2001-01-01

In this randomized trial, we enrolled 30 patients treated for a distal radius Colles' type fracture. The fractures were reduced if necessary and fixed in a below-elbow plaster cast for 5 weeks. One group consisting of 14 patients received instructions for shoulder; elbow and finger exercise and the other group consisting of 16 patients had occupational therapy. At 5 weeks, 3 and 9 months we measured the functional scores. There were no statistically significant differences between the groups at any time. It seems that for non-surgically treated patients with a distal radius fracture only instructions are necessary.

The Evaluation of Effect of Developer Age in the Detection of Approximal Caries Using Three Speed Dental X-Ray Films: An In-Vitro Study

PubMed Central

Madalli, Vijaylaxmi B; Annigeri, Rajeshwari G; Basavaraddi, Shrinivas M

2014-01-01

Background and Objectives: Ever since the first radiograph was taken in 1895, radiographs have become an essential part of dental practice. Since radiation exposure for the patients is a major concern, it is important for us to reduce the radiation exposure to the patient and surrounding environment, without compromising the quality of image. Since improper film processing is one of the major causes of poor image quality, it is very important to test dental films under a variety of processing conditions. So this study was conducted to compare the diagnostic accuracy between Kodak Ultraspeed, Ektaspeed and Agfa Dentus M2 Comfort films for the detection of approximal caries in fresh as well as in aged processing solution. Methods: Hundred extracted unrestored maxillary and mandibular teeth were aligned in a group of five teeth in each plaster model. Total of 20 plaster models were constructed and only 3 teeth in the middle were utilized for the study. The final sample consisted of 60 teeth in the study. The exposure time for Ultraspeed film was standardized at 0.5 seconds and for Ektaspeed and Agfa Dentus M2 films, the exposure time was 0.32 seconds. For each radiograph two blocks were used simulating bitewing radiograph. All 20 plaster blocks were exposed using three film types at standardized exposure timings with 30 radiographs each week. The procedure was repeated every week until 6 weeks. Radiographs were evaluated by an observer and assessed by following four point scale 0- sound tooth, 1- lesion in enamel, 2- lesion in amelodentinal junction, 3- dentinal lesion. Only distal surfaces were assessed. Thereafter all the teeth were subjected for histological study and actual depth of the lesion was recorded which acted as gold standard and this reading was subtracted in observer readings after radiographic examination. All data collected were analyzed statistically using ANOVA, paired and unpaired t-tests. Results: Ektaspeed and Agfa films required less exposure compared to Ultraspeed film. With respect to film, all films had equal diagnostic accuracy upto three weeks. From fourth week Ultraspeed and Agfa films were considerably better than E speed film. E speed film was inferior in the depleted solution compared to other two solutions. With respect to lesion detection Agfa film was inferior to other two films. Conclusion: All three films had equal diagnostic accuracy in fresh solution. Considering the significant reduction in patient radiation with Ektaspeed film, this should be the film of choice whenever possible. As far as the diagnosis of approximal caries is concerned processing solutions should not be used longer than 3 weeks. PMID:24783146

The evaluation of effect of developer age in the detection of approximal caries using three speed dental x-ray films: an in-vitro study.

PubMed

Madalli, Vijaylaxmi B; Annigeri, Rajeshwari G; Basavaraddi, Shrinivas M

2014-03-01

Ever since the first radiograph was taken in 1895, radiographs have become an essential part of dental practice. Since radiation exposure for the patients is a major concern, it is important for us to reduce the radiation exposure to the patient and surrounding environment, without compromising the quality of image. Since improper film processing is one of the major causes of poor image quality, it is very important to test dental films under a variety of processing conditions. So this study was conducted to compare the diagnostic accuracy between Kodak Ultraspeed, Ektaspeed and Agfa Dentus M2 Comfort films for the detection of approximal caries in fresh as well as in aged processing solution. Hundred extracted unrestored maxillary and mandibular teeth were aligned in a group of five teeth in each plaster model. Total of 20 plaster models were constructed and only 3 teeth in the middle were utilized for the study. The final sample consisted of 60 teeth in the study. The exposure time for Ultraspeed film was standardized at 0.5 seconds and for Ektaspeed and Agfa Dentus M2 films, the exposure time was 0.32 seconds. For each radiograph two blocks were used simulating bitewing radiograph. All 20 plaster blocks were exposed using three film types at standardized exposure timings with 30 radiographs each week. The procedure was repeated every week until 6 weeks. Radiographs were evaluated by an observer and assessed by following four point scale 0- sound tooth, 1- lesion in enamel, 2- lesion in amelodentinal junction, 3- dentinal lesion. Only distal surfaces were assessed. Thereafter all the teeth were subjected for histological study and actual depth of the lesion was recorded which acted as gold standard and this reading was subtracted in observer readings after radiographic examination. All data collected were analyzed statistically using ANOVA, paired and unpaired t-tests. Ektaspeed and Agfa films required less exposure compared to Ultraspeed film. With respect to film, all films had equal diagnostic accuracy upto three weeks. From fourth week Ultraspeed and Agfa films were considerably better than E speed film. E speed film was inferior in the depleted solution compared to other two solutions. With respect to lesion detection Agfa film was inferior to other two films. All three films had equal diagnostic accuracy in fresh solution. Considering the significant reduction in patient radiation with Ektaspeed film, this should be the film of choice whenever possible. As far as the diagnosis of approximal caries is concerned processing solutions should not be used longer than 3 weeks.

Mega-features at the Table Rock phreatomagmatic complex in Christmas Valley, Oregon; Law of original horizontality need not apply

NASA Astrophysics Data System (ADS)

Brand, B. D.; Clarke, A.

2006-12-01

The Table Rock Complex (TRC; Pliocene-Pleistocene), first documented and described by (Heiken, 1971, J. Geophy Res, 76, 5615-5626) is a large and well exposed phreatomagmatic complex in the Fort Rock- Christmas Lake Valley Basin, south-central Oregon. It is ~7 by 5 km and contains two large phreatomagmatic edifices; a large southern tuff cone with a capping lava lake (TRC1), and a large broad tuff ring in the northeast (TRC2). At least five additional, smaller tuff rings were identified along the flanks of the complex, yielding a complicated network of tuff ring-tuff cone deposits. Based on the low accidental component and evidence for a lake during this time, the cause of the explosive eruptions is interpreted to be due to interaction of magma with shallow standing water. The TRC1 consists of fining-up sequences, large erosive channel scour and fill deposits, massive tuff breccias, and abundant soft sediment deformation, which suggests deposition within a standing body of water. Subaerial TRC1 deposits are found south of the edifice, but are not exposed in the north. A significant repose period occurred between the TRC1 and TRC2 eruptions, evidenced by a wave-cut terrace and 25-50 cm of diatomitic lake sediments. TRC2 produced multiple, extremely erosive pyroclastic surges, which cut and scour the TRC1 deposits. Surge deposits consist of 50-200 m wavelength cross-beds, in some areas form large U-shaped features (10-100 m deep), and can be seen plastering up and around large obstacles from previous vents. The surge-deposits blanket all other sequences and create a hummocky topography around the edifice. This suggests that TRC2 was the last eruption in the sequence. The weight of the TRC2 sediments caused the water-saturated TRC1 sediments to plastically deform into large ball and pillow features and overturned slump blocks on the order of 20-50 m thick. The smaller flank tuff-ring eruptions likely occurred sometime between the TRC1 and TRC2 events. The inner-craters of these vents are well exposed and show features such as near-vertical plastered beds, large-scale convolute bedding, and in some places deformed and folded slump blocks up to 20-120 m thick. The features observed in both TRC deposits and in the smaller flank tuff rings (e.g., large-scale soft sediment deformation, plastered-vertical bedding, accretionary/armored lapilli) are consistent with a high water-magma ratio. The highly erosive surge beds of TRC2 represent the most energetic pulse of the eruptions.

Study by micro-Raman spectroscopy of wall paints (external parts and cross-sections) from reales alcazares of Seville (Spain)

NASA Astrophysics Data System (ADS)

Perez-Rodriguez, José Luis; Centeno, Miguel Angel; Robador, María Dolores; Siguenza, Belinda; Durán, Adrián

2013-04-01

The Reales Alcazares of Sevilla was originally builded by the Arabic in the year 913. The Mudejar Palace was built by Christian King Pedro I between 1364 and 1366. At the end of XV century the Catholic Kings, Isabel and Fernando made important transformations especially in the Mudejar Palace. Recently, wall paints from Catholic Kings periods were found during works of conservations in the first floor of the Palace. The study of these paints by non-destructive techniques was considered of great interest in order to determine the technology of manufacture and the originality of the artwork. The main objective of this work was to apply the Raman spectroscopy technique on the surface of the wall and on the different layers of the cross-sections prepared in order to characterize the pigments and the plaster present in these wall paints. Little information was obtained using a portable Raman spectrometer. In this case the dispersive integrated Horiba Jobin-Yvon LabRaman HR800 system was employed. Small samples of black, red, yellow, white and green colour were taken from the artwork. The surface of the samples were directly studed by the Raman spectroscopy instrument using red (785 nm) and green (522 nm) lasers, similarly to non-invasive experimental technique. This technique showed the presence of gypsum (SO4Ca.2H2O) and calcite (CaCO3) in all the studied samples However, the pigments responsible of different colours were not detected. The surface of these wall paints was covered with gypsum and calcite due to contamination. These mineras were also characterized by XRD and SEM-EDX. The presence of these compounds and the heterogeneous surface did not permit the characterization of the pigments responsible of the colour. In order to better characterization of the pigments and plaster used the study was carried out on cross-sections. The black colour was performed using carbon black. Two different red layers were detected one constituted by cinnabar and lead carbonate and the other one by iron oxides. The green and white colours were constituted by atacamite and calcite, respectively. In addition lead white was detected in green colour. The white layers (plaster) located under the colour layers were constituted by calcite, quartz and feldspars. These data confirm the use of fresco technique. The study of the surface (external part) by micro-Raman spectroscopy limited the characterization of the pigments present in these wall pains, due to the presence of a layer of gypsum deposited on the surface. By other hand, the study by Raman spectroscopy of the cross-sections allowed the characterization of different pigments and support used in the manufacture of these wall paints.

The Effect of Awareness of American Board of Orthodontics Criteria on Treatment Outcomes in a Postgraduate Dental Clinic.

PubMed

Yilmaz, Rahime Burcu Nur; Nalbantgil, Didem; Ozdemir, Fulya

2016-09-01

The aims of this study were to evaluate the posttreatment outcomes in a postgraduate orthodontic clinic following a course on American Board of Orthodontics Cast and Radiograph Evaluation (ABO-CRE); to compare the outcomes of postgraduate students who took the course before and after finishing treatment of their cases; and to assess if the need for orthodontic treatment as determined by the Index of Orthodontic Treatment Need (IOTN) at the beginning of treatment affected students' final scores. A course on ABO-CRE was given to second- (group A), third- (group B), and fourth- (group C) year postgraduate students at Yeditepe University, Istanbul, Turkey, in 2012. Pre- and posttreatment plaster models of 253 cases (group A) were treated by students in 2011-12. An additional 251 (group B, 2012-13) and 341 (group C, 2013-14) cases were evaluated in the first and second years after the course, respectively. The models were graded retrospectively using the ABO-CRE and IOTN. The results showed that the total mean scores on the posttreatment plaster models were significantly higher in the pre-course group than the first- and second-year post-course group (p<0.05 and p<0.01, respectively). The borderline cases (grade 3) received a lower score on the ABO-CRE than the cases with need (grade 4) (p<0.01) and severe need (grade 5) (p<0.01) for orthodontic treatment. Increasing awareness by giving information about the ABO-CRE significantly improved the posttreatment success of these postgraduate students. After the course, treatment outcomes in the following year were better than two years later, suggesting it may be useful to teach the course annually to refresh students' knowledge.

Dental measurements and Bolton index reliability and accuracy obtained from 2D digital, 3D segmented CBCT, and 3d intraoral laser scanner

PubMed Central

San José, Verónica; Bellot-Arcís, Carlos; Tarazona, Beatriz; Zamora, Natalia; O Lagravère, Manuel

2017-01-01

Background To compare the reliability and accuracy of direct and indirect dental measurements derived from two types of 3D virtual models: generated by intraoral laser scanning (ILS) and segmented cone beam computed tomography (CBCT), comparing these with a 2D digital model. Material and Methods One hundred patients were selected. All patients’ records included initial plaster models, an intraoral scan and a CBCT. Patients´ dental arches were scanned with the iTero® intraoral scanner while the CBCTs were segmented to create three-dimensional models. To obtain 2D digital models, plaster models were scanned using a conventional 2D scanner. When digital models had been obtained using these three methods, direct dental measurements were measured and indirect measurements were calculated. Differences between methods were assessed by means of paired t-tests and regression models. Intra and inter-observer error were analyzed using Dahlberg´s d and coefficients of variation. Results Intraobserver and interobserver error for the ILS model was less than 0.44 mm while for segmented CBCT models, the error was less than 0.97 mm. ILS models provided statistically and clinically acceptable accuracy for all dental measurements, while CBCT models showed a tendency to underestimate measurements in the lower arch, although within the limits of clinical acceptability. Conclusions ILS and CBCT segmented models are both reliable and accurate for dental measurements. Integration of ILS with CBCT scans would get dental and skeletal information altogether. Key words:CBCT, intraoral laser scanner, 2D digital models, 3D models, dental measurements, reliability. PMID:29410764

Intraoral 3D Scanning or Dental Impressions for the Assessment of Dental Arch Relationships in Cleft Care: Which is Superior?

PubMed

Chalmers, E V; McIntyre, G T; Wang, W; Gillgrass, T; Martin, C B; Mossey, P A

2016-09-01

This study was undertaken to evaluate intraoral 3D scans for assessing dental arch relationships and obtain patient/parent perceptions of impressions and intraoral 3D scanning. Forty-three subjects with nonsyndromic unilateral cleft lip and palate (UCLP) had impressions taken for plaster models. These and the teeth were scanned using the R700 Orthodontic Study Model Scanner and Trios® Digital Impressions Scanner (3Shape A/S, Copenhagen, Denmark) to create indirect and direct digital models. All model formats were scored by three observers on two occasions using the GOSLON and modified Huddart Bodenham (MHB) indices. Participants and parents scored their perceptions of impressions and scanning from 1 (very good) to 5 (very bad). Intra- and interexaminer reliability were tested using GOSLON and MHB data (Cronbach's Alpha >0.9). Bland and Altman plots were created for MHB data, with each model medium (one-sample t tests, P < .05) and questionnaire data (Wilcoxon signed ranks P < .05) tested. Intra- and interexaminer reliability (>0.9) were good for all formats with the direct digital models having the lowest interexaminer differences. Participants had higher ratings for scanning comfort (84.8%) than impressions (44.2%) (P < .05) and for scanning time (56.6%) than impressions (51.2%) (P > .05). None disliked scanning, but 16.3% disliked impressions. Data for parents and children positively correlated (P < .05). Reliability of scoring dental arch relationships using intraoral 3D scans was superior to indirect digital and to plaster models; Subjects with UCLP preferred intra-oral 3D scanning to dental impressions, mirrored by parents/carers; This study supports the replacement of conventional impressions with intra-oral 3D scans in longitudinal evaluations of the outcomes of cleft care.

An extremely sensitive species-specific ARMS PCR test for the presence of tiger bone DNA.

PubMed

Wetton, Jon H; Tsang, Carol S F; Roney, Chris A; Spriggs, Adrian C

2002-04-18

The survival of the tiger (Panthera tigris) is seriously threatened by poaching to provide raw materials for traditional Chinese medicines (TCMs). Most highly prized are the tiger's bones, which are used in combination with other animal and plant derivatives in pills and plasters for the treatment of rheumatism and other ailments. Hundreds of patent remedies have been produced which claim to contain tiger bone, but proof of its presence is needed if legislation prohibiting the trade in endangered species is to be enforced.A highly sensitive tiger-specific real-time PCR assay has been developed to address this problem. Using primers specific to the tiger mitochondrial cytochrome b gene, successful amplification has been reliably achieved from blood, hair and bone as well as from a range of TCMs spiked with 0.5% tiger bone. Although capable of detecting fewer than 10 substrate molecules, the seven varieties of TCM pills and plasters tested showed no detectable trace of tiger DNA before spiking. Furthermore, sequencing several "tiger bone" fragments seized from TCM shops has shown that they actually originated from cattle and pigs. The potential effects of traditional bone preparation methods, evidence that much lower concentrations are used than alleged on TCM packaging, and substitution of bones from other species all suggest a low likelihood of detecting tiger DNA in patent medicines. Despite this, the basic methods have been thoroughly proven and can be readily applied to derivatives from other Convention on International Trade in Endangered Species of Wild Fauna and Flora (CITES) protected species, providing a rapid and highly sensitive forensic test for species of origin. Potential applications to the monitoring of wild populations are demonstrated by the successful identification of shed hairs and faecal samples.

Approximal sealings on lesions in neighbouring teeth requiring operative treatment: an in vitro study.

PubMed

Cartagena, Alvaro; Bakhshandeh, Azam; Ekstrand, Kim Rud

2018-02-07

With this in vitro study we aimed to assess the possibility of precise application of sealant on accessible artificial white spot lesions (WSL) on approximal surfaces next to a tooth surface under operative treatment. A secondary aim was to evaluate whether the use of magnifying glasses improved the application precision. Fifty-six extracted premolars were selected, approximal WSL lesions were created with 15% HCl gel and standardized photographs were taken. The premolars were mounted in plaster-models in contact with a neighbouring molar with Class II/I-II restoration (Sample 1) or approximal, cavitated dentin lesion (Sample 2). The restorations or the lesion were removed, and Clinpro Sealant was placed over the WSL. Magnifying glasses were used when sealing half the study material. The sealed premolar was removed from the plaster-model and photographed. Adobe Photoshop was used to measure the size of WSL and sealed area. The degree of match between the areas was determined in Photoshop. Interclass agreement for WSL, sealed, and matched areas were found as excellent (κ = 0.98-0.99). The sealant covered 48-100% of the WSL-area (median = 93%) in Sample 1 and 68-100% of the WSL-area (median = 95%) in Sample 2. No statistical differences were observed concerning uncovered proportions of the WSL-area between groups with and without using magnifying glasses (p values ≥ .19). However, overextended sealed areas were more pronounced when magnification was used (p = .01). The precision did not differ between the samples (p = .31). It was possible to seal accessible approximal lesions with high precision. Use of magnifying glasses did not improve the precision.

Seismic risk evaluation aided by IR thermography

NASA Astrophysics Data System (ADS)

Grinzato, E.; Cadelano, G.; Bison, P.; Petracca, A.

2009-05-01

Conservation of buildings in areas at seismic risk must take prevention into account. The safeguard architectonic heritage is an ambitious objective, but a priority for planning programmes at varying levels of decision making. Preservation and restoration activities must be optimized to cover a vast and widespread historical and architectonic heritage present in many countries. Masonry buildings requires an adequate level of knowledge based on the importance of structural geometry, which may include the damage, details of construction and properties of materials. For identification and classification of masonry is necessary to find shape, type and size of the elements, texture, size of mortar joints, assemblage. The recognition can be done through a visual inspection of the surface of walls, which can be examined, where is not visible, removing a layer of plaster. Thermography is an excellent tool for a fast survey and collection of vital information for this purpose, but it is extremely important define a precise procedure in the development of more efficient monitoring tools. Thermography is a non-destructive method that allows recognizing the structural damage below plaster, detecting the presence of discontinuity in masonry, for added storeys, cavity, filled openings, and repairs. Furthermore, the fast identification of subsurface state allows to select areas where other methods either more penetrating or partially destructive have to be applied. The paper reports experimental results achieved in the mainframe of the European project RECES Modiquus. The main aim of the project is to improve methods, techniques and instruments for facing antiseismic options. Both passive and active thermographic techniques have been applied in different weather conditions and time schemes. A dedicated algorithm has been developed to enhance the visibility of wall bonding.

Plasma pharmacokinetics and synovial concentrations of S-flurbiprofen plaster in humans.

PubMed

Yataba, Ikuko; Otsuka, Noboru; Matsushita, Isao; Kamezawa, Miho; Yamada, Ichimaro; Sasaki, Sigeru; Uebaba, Kazuo; Matsumoto, Hideo; Hoshino, Yuichi

2016-01-01

The purpose of this study is to investigate the pharmacokinetics and deep tissue penetration capability of the newly developed S-flurbiprofen plaster (SFPP) in humans. Study 1: SFPP tape-type patch (2-60 mg) was applied to the lower back for 24 h in healthy adult volunteers. S-flurbiprofen (SFP) plasma concentration was measured over time to examine SFP pharmacokinetics. Study 2: SFPP (20 mg) was applied for 12 h to the affected knee of osteoarthritis (OA) patients who were scheduled for total knee arthroplasty. Deep tissues (synovial tissue and synovial fluid) were collected during surgery to compare SFP concentrations after application of SFPP or a commercially available flurbiprofen (FP) gel-type patch. Study 1: The plasma concentration of SFP was sustained during 24-h topical application of the SFPP, showing a high percutaneous absorption ratio of 51.4-72.2 %. Cmax and AUC0-∞ were dose-proportional. Study 2: After application of the SFPP for 12 h, SFP concentrations in the synovial tissue and synovial fluid were 14.8-fold (p = 0.002) and 32.7-fold (p < 0.001) higher, respectively, than those achieved by the FP patch. Sustained plasma concentration of SFP and high percutaneous absorption ratio was observed after 24-h topical application of the SFPP. Compared to the FP patch, the SFPP showed superior percutaneous absorption and greater tissue penetration of SFP into the synovial tissue. Greater tissue penetration of the SFPP seemed to be primarily due to its formulation. Thus, SFPP is expected to show higher efficacy for the treatment of knee OA.

Driving with a short arm cast in a simulator.

PubMed

Mansour, Damian; Mansour, Kristin Gotaas; Kenny, Benjamin William; Attia, John; Meads, Bryce

2015-12-01

To test the ability to steer in a driving simulator in subjects with a short arm cast. 17 men and 13 women aged 23 to 67 (mean, 37) years who had a valid driver's licence were randomised to the cast-first group (n=16; 7 had the cast on the dominant arm) or the cast-second group (n=14; 8 had the cast on the dominant arm) and drove in a simulator. A short arm plaster-of-Paris cast was applied in a neutral position, allowing free movement of the metacarpophalangeal joints, thumb, and elbow joint. Outcome measures included the number of driving off track instances, the number of crashes, the lap time, and the effect of hand dominance on these parameters. Subjects were asked whether the cast had impeded their steering ability. Subjects with or without a cast were comparable in terms of the number of driving off track instances, number of crashes, and lap time. Compared with no cast, the odds ratio (OR) of a subject in a cast driving off the track was 1.02 (p=0.921) and having a crash was 0.79 (p=0.047). All subjects were 1.23 times more likely to drive off the track in their first lap (OR=2.66, p=0.019). The mean lap time decreased for each consecutive lap from the 2nd to 5th laps. Subjects driving with a cast on the dominant or non-dominant arm were comparable. 26 out of the 30 participants considered that the plaster cast impeded their steering ability. Compared with no cast, driving with a short arm cast did not significantly decrease steering ability in a driving simulator.

Analysis of a trial assessing the long-term effectiveness of salicylic acid plasters compared with scalpel debridement in facilitating corn resolution in patients with multiple corns.

PubMed

Stephenson, John; Farndon, Lisa; Concannon, Michael

2016-06-01

This study assesses the effect of salicylic acid plasters on the time to resolution of 324 corns experienced by 201 participants taking part in a randomized controlled trial. While the rate of corn resolution was substantively higher in the treatment group than in the control group, treatment was found to be not significantly related to time to corn recurrence when analyzed over the full 12-month follow-up period. Parametric survival analysis modeling of interval-censored data and incorporating patient-specific frailty terms was utilized, to model correlation of corns within patients (hazard ratio [HR], 1.189; 95% confidence interval [CI], 0.780-1.813; P = 0.422). Median resolution times were 10.0 months for corns in the treatment group and 13.4 months for corns in the control group. Controlling for treatment, corn type was found to be related to resolution time, with dorsal/interdigital (ID) corns showing better resolution than plantar corns (HR, 1.670; 95% CI, 1.061-2.630; P = 0.027). Median resolution times were 5.9 months for dorsal/ID corns and 14.9 months for plantar corns. Secondary measures relating to quality of life (QoL) and foot-related disability, using the EQ-5D questionnaire and the Manchester Foot Pain and Disability Index (MFPDI), were also assessed at the patient level in multivariate models. Treatment was not significantly related to any of these measures over the whole period of analysis. However, a trend analysis revealed a quadratic trend in QoL and MFPDI scores, arising from a substantive initial improvement between baseline and 3 months, followed by a gradual decrease between 3 and 12 months. © 2015 Japanese Dermatological Association.

Chest wall restriction limits high airway pressure-induced lung injury in young rabbits.

PubMed

Hernandez, L A; Peevy, K J; Moise, A A; Parker, J C

1989-05-01

High peak inspiratory pressures (PIP) during mechanical ventilation can induce lung injury. In the present study we compare the respective roles of high tidal volume with high PIP in intact immature rabbits to determine whether the increase in capillary permeability is the result of overdistension of the lung or direct pressure effects. New Zealand White rabbits were assigned to one of three protocols, which produced different degrees of inspiratory volume limitation: intact closed-chest animals (CC), closed-chest animals with a full-body plaster cast (C), and isolated excised lungs (IL). The intact animals were ventilated at 15, 30, or 45 cmH2O PIP for 1 h, and the lungs of the CC and C groups were placed in an isolated lung perfusion system. Microvascular permeability was evaluated using the capillary filtration coefficient (Kfc). Base-line Kfc for isolated lungs before ventilation was 0.33 +/- 0.31 ml.min-1.cmH2O-1.100g-1 and was not different from the Kfc in the CC group ventilated with 15 cmH2O PIP. Kfc increased by 850% after ventilation with only 15 cmH2O PIP in the unrestricted IL group, and in the CC group Kfc increased by 31% after 30 cmH2O PIP and 430% after 45 cmH2O PIP. Inspiratory volume limitation by the plaster cast in the C group prevented any significant increase in Kfc at the PIP values used. These data indicate that volume distension of the lung rather than high PIP per se produces microvascular damage in the immature rabbit lung.

Deep sea sedimentation processes and geomorphology: Northwest Atlantic continental margin

NASA Astrophysics Data System (ADS)

Mosher, David; Campbell, Calvin; Gardner, Jim; Chaytor, Jason; Piper, David; Rebesco, Michele

2017-04-01

Deep-sea sedimentation processes impart a fundamental control on the morphology of the western North Atlantic continental margin from Blake Spur to Hudson Strait. This fact is illustrated by the variable patterns of cross-margin gradients that are based on extensive new multibeam echo-sounder data informed by subbottom profiler and seismic reflection data. Erosion by off-shelf sediment transport in turbidity currents creates gullies, canyons and channels and a steep upper slope. Amalgamation of these conduits produces singular channels and turbidite fan complexes on the lower slope, flattening slope-profile gradients. The effect is an exponentially decaying "graded" slope profile. Comparatively, sediment mass failure produces steeper upper slopes due to head scarp development and a wedging architecture to the lower slope as deposits thin in the downslope direction. This process results in either a "stepped" slope, and/or a significant downslope gradient change where MTDs pinch out. Large drift deposits created by geostrophic currents are developed all along the margin. Blake Ridge, Sackville Spur, and Hamilton Spur are large detached drifts on disparate parts of the margin. They form a linear "above grade" profile along their crests from the shelf to abyssal plain. Deeper portions of the US continental margin are dominated by the Chesapeake Drift and Hatteras Outer Ridge; both plastered elongate mounded drifts. Farther north, particularly on the Grand Banks margin, are plastered and separated drifts. These drifts form "stepped" slope profiles, where they onlap the margin. Trough-mouth fan complexes become more common along the margin with increasing latitude. Sediment deposition and retention, particularly those dominated by glacigenic debris flows, characterize these segments producing an "above grade" slope profile. Understanding these geomorphological consequences of deep sea sedimentation processes is important to extended continental shelf mapping in which gradients and gradient change is a critical metric.

Comparison of the occlusal contact area of virtual models and actual models: a comparative in vitro study on Class I and Class II malocclusion models.

PubMed

Lee, Hyemin; Cha, Jooly; Chun, Youn-Sic; Kim, Minji

2018-06-19

The occlusal registration of virtual models taken by intraoral scanners sometimes shows patterns which seem much different from the patients' occlusion. Therefore, this study aims to evaluate the accuracy of virtual occlusion by comparing virtual occlusal contact area with actual occlusal contact area using a plaster model in vitro. Plaster dental models, 24 sets of Class I models and 20 sets of Class II models, were divided into a Molar, Premolar, and Anterior group. The occlusal contact areas calculated by the Prescale method and the virtual occlusion by scanning method were compared, and the ratio of the molar and incisor area were compared in order to find any particular tendencies. There was no significant difference between the Prescale results and the scanner results in both the molar and premolar groups (p = 0.083 and 0.053, respectively). On the other hand, there was a significant difference between the Prescale and the scanner results in the anterior group with the scanner results presenting overestimation of the occlusal contact points (p < 0.05). In Molars group, the regression analysis shows that the two variables express linear correlation and has a linear equation with a slope of 0.917. R 2 is 0.930. Groups of Premolars and Anteriors had a week linear relationship and greater dispersion. Difference between the actual and virtual occlusion revealed in the anterior portion, where overestimation was observed in the virtual model obtained from the scanning method. Nevertheless, molar and premolar areas showed relatively accurate occlusal contact area in the virtual model.

Evaluation of the thermal and structural performance of straw bale construction

NASA Astrophysics Data System (ADS)

Beaudry, Kyle R.

This thesis is primarily divided into two distinct experimental programs evaluating: 1) the thermal performance and, 2) the structural performance of straw bale construction. The thermal performance chapter describes hot-box testing (based on ASTM C1363-11) of seven straw bale wall panels to obtain their apparent thermal conductivity values. All panels were constructed with stacked bales and cement-lime plaster skins on each side of the bales. Four panels were made with traditional, 2-string field bales of densities ranging from 89.5 kg/m3 - 131 kg/m3 and with the bales on-edge (fibres perpendicular to the heat flow). Three panels were made with manufactured high-density bales (291 kg/m3 - 372 kg/m3). The fibres of the manufactured bales were randomly oriented. The key conclusion of this work is that within the experimental error, there is no difference in the apparent thermal conductivity value for panels using normal density bales and manufactured high-density bales up to a density of 333 kg/m3. The structural performance chapter describes gravity and transverse load testing (based on ASTM E72-15) of non-plastered modular straw bale wall (DBW) panels to evaluate their strength capacity and failure modes. The out-of-plane flexural (OPF) tests exhibited a mean ultimate bending moment of 49.7 kNm. The axial compression (AC) tests exhibited a mean ultimate line load of 161.0 kN/m. The local flexural header beam (HP) tests exhibited an ultimate line load of 31.6 kN/m. The OPF and AC capacities of the DBW exceeded the capacities exhibited by a conventional 38 mm x 140 mm stud wall. However, the DBW's header beam strength and stiffness was inferior to conventional stud wall.

Biocompatability of hydroxyapatite composite as a local drug delivery system.

PubMed

Krisanapiboon, A; Buranapanitkit, B; Oungbho, K

2006-12-01

To investigate the biocompatibility of hydroxyapatite composite (hydroxyapatite, plaster of Paris, and chitosan) impregnated with gentamicin, fosfomycin, imipenem, or amphotericin B. The interactions of the extract from each drug against osteoblast were tested using the methylthiotetrazole test. Extracts from all drugs showed good biocompatibility at concentrations varying from 10 microgram/ml to 1000 microgram/ml. Imipenem and amphotericin B at a concentration of 1000 microgram/ml had a significantly higher percentage of cell viability than the control group. No morphological change of osteoblast was observed in all drug tests at any concentrations. The hydroxyapatite composite had a good biocompatibility for carrying gentamicin, fosfomycin, imipenem, or amphotericin B.

Well-differentiated Papillary Mesothelioma of the Tunica Vaginalis.

PubMed

Tan, Wei Keith; Tan, Mae-Yen; Tan, Hui Meng; Pathmanathan, Rajadurai; Tan, Wei Phin

2016-04-01

A 39-year-old man presented with painless scrotal swelling for 2 months. He denied any asbestos exposure but worked with wall and ceiling plaster. Physical exam revealed a large right scrotum which transilluminated. Scrotal ultrasonography revealed a large right hydrocele and a polypoidal mass along the anterior wall of the scrotum. Magnetic resonance imaging of the abdomen and computed tomography of the chest showed no metastases. He underwent a right inguinal scrotal exploration and wide excision of tunica vaginalis and a partial epididymectomy. Pathology revealed well-differentiated papillary mesothelioma of the tunica vaginalis. The patient had an uneventful recovery. Copyright © 2016 Elsevier Inc. All rights reserved.

Bandages and difficulty with bathing: introducing Seal-Tight.

PubMed

Lindsay, Ellie

2005-06-01

Patients with compression bandages experience difficulty with bathing due to the possibility that bandages may become wet and affect the wound. Bandage and dressing changes resulting from accidental wetting also cost the NHS considerable time and money. This product focus highlights the social and psychological impact on the patient when they are unable to bathe and offers a solution to the problem. Seal-Tight is a product that has been newly placed on the drug tariff, making it widely available to all patients who wear bandages (or plaster casts). Seal-Tight enables the patient to bathe, in some cases for the first time for months or even years.

Unconstrained paving and plastering method for generating finite element meshes

DOEpatents

Staten, Matthew L.; Owen, Steven J.; Blacker, Teddy D.; Kerr, Robert

2010-03-02

Computer software for and a method of generating a conformal all quadrilateral or hexahedral mesh comprising selecting an object with unmeshed boundaries and performing the following while unmeshed voids are larger than twice a desired element size and unrecognizable as either a midpoint subdividable or pave-and-sweepable polyhedra: selecting a front to advance; based on sizes of fronts and angles with adjacent fronts, determining which adjacent fronts should be advanced with the selected front; advancing the fronts; detecting proximities with other nearby fronts; resolving any found proximities; forming quadrilaterals or unconstrained columns of hexahedra where two layers cross; and establishing hexahedral elements where three layers cross.

Thermodynamic and spectroscopic speciation to explain the blackening process of hematite formed by atmospheric SO2 impact: the case of Marcus Lucretius House (Pompeii).

PubMed

Maguregui, Maite; Knuutinen, Ulla; Martínez-Arkarazo, Irantzu; Castro, Kepa; Madariaga, Juan M

2011-05-01

After many decades exposed to a polluted environment, in some areas of Marcus Lucretius House, there are clear signs that plasters and hematite pigments are suffering deterioration. In the exhaustive analysis of the black layer covering the red pigment hematite it was possible to identify magnetite (Fe(3)O(4)) as responsible for the black colour, which always appears in combination with gypsum. Thermodynamic modelling stated that the presence of gypsum as well as the transformation of hematite into magnetite is a consequence of the attack of atmospheric SO(2).

Study of the thermal properties of selected PCMs for latent heat storage in buildings

NASA Astrophysics Data System (ADS)

Valentova, Katerina; Pechackova, Katerina; Prikryl, Radek; Ostry, Milan; Zmeskal, Oldrich

2017-07-01

The paper is focused on measurements of thermal properties of selected phase change materials (PCMs) which can be used for latent heat storage in building structures. The thermal properties were measured by the transient step-wise method and analyzed by the thermal spectroscopy. The results of three different materials (RT18HC, RT28HC, and RT35HC) and their thermal properties in solid, liquid, and phase change region were determined. They were correlated with the differential scanning calorimetry (DSC) measurement. The results will be used to determine the optimum ratio of components for the construction of drywall and plasters containing listed ingredients, respectively.

A new seamless, smooth, interior, absorptive finishing system

NASA Astrophysics Data System (ADS)

D'Antonio, Peter

2003-04-01

Architects and acousticians have sought a field-applied, absorptive finishing system that resembles a smooth plaster or painted drywall surface, since the dawn of architectural acoustics. Some success has been achieved using sprayed cellulose or cementitious materials, but surface smoothness has been a challenge. A new approach utilizing a thin microporous layer of mineral particles applied over a mineral wool panel will be described. This material can be applied to almost any shape surface, internally pigmented to match almost any color and renovated. It is currently finding application in many architectural applications, including museums. A recent installation in the New Pinakothek Museum in Munich will be illustrated.

Experimental joint immobilization in guinea pigs. Effects on the knee joint

NASA Technical Reports Server (NTRS)

Marcondesdesouza, J. P.; Machado, F. F.; Sesso, A.; Valeri, V.

1980-01-01

In young and adult guinea pigs, the aftermath experimentally induced by the immobilization of the knee joint in hyperextended forced position was studied. Joint immobilization which varied from one to nine weeks was attained by plaster. Eighty knee joints were examined macro and microscopically. Findings included: (1) muscular hypotrophy and joint stiffness in all animals, directly proportional to the length of immobilization; (2) haemoarthrosis in the first week; (3) intra-articular fibrous tissue proliferation ending up with fibrous ankylosis; (4) hyaline articular cartilage erosions; (5) various degrees of destructive menisci changes. A tentative explanation of the fibrous tissue proliferation and of the cartilage changes is offered.

The radiation crosslinking process and new products

NASA Astrophysics Data System (ADS)

Ueno, Keiji

In 1988 there were over 90 EB accelerators for industrial use in Japan. The number one industrial application was Wire and Cable, the 2nd was PE foam and Curing, and the 3rd was Precure of tyre. R & D has a very high ration of EB accelerator use. Low energy industrial applications were coated steel (white board), plaster slab, coated paper, magnetic tape and floppy disks. As a new application of the radiation crosslinking process, we have studied radiation crosslinking of engineering plastics and succeeded in improving the hea tresistivity without using glass fibers. Many kinds of polyfunctional monomers used as crosslinking reagents of irradiated Nylon and PBT were studied.

Fra Angelico's painting technique revealed by terahertz time-domain imaging (THz-TDI)

NASA Astrophysics Data System (ADS)

Koch Dandolo, Corinna Ludovica; Picollo, Marcello; Cucci, Costanza; Jepsen, Peter Uhd

2016-10-01

We have investigated with terahertz time-domain imaging (THz-TDI) the well-known Lamentation over the dead Christ panel painting (San Marco Museum, Florence) painted by Fra Giovanni Angelico within 1436 and 1441. The investigation provided a better understanding of the construction and gilding technique used by the eminent artist, as well as the plastering technique used during the nineteenth-century restoration intervention. The evidence obtained from THz-TDI scans was correlated with the available documentation on the preservation history of the art piece. Erosion and damages documented for the wooden support, especially in the lower margin, found confirmation in the THz-TD images.

3D reconstruction of the structure of a residual limb for customising the design of a prosthetic socket.

PubMed

Shuxian, Zheng; Wanhua, Zhao; Bingheng, Lu

2005-01-01

Aiming at overcoming the limitations of the plaster-casting method in traditional prosthetic socket fabrication, the idea of reconstructing the 3D models for bones and skin of the residual limb is proposed. Given the two-dimensional obtained image through CT scanning, using image processing and reverse engineering techniques, the 3D solid model of the residual limb can be successfully reconstructed. The new approach can reproduce both the internal and the external structure of the residual limb. It can moreover avoid making a positive mould by the way of manual modifications. In addition to this, it can provide a scientific basis for the individualization of prosthetic socket design.

National Register of Historic Places Significance Testing at Six Sites (23SO: 459, 465, 471, 496, 497, and 500) in the Castor River Enlargement Project, Stoddard County, Missouri

DTIC Science & Technology

1985-09-16

Spanish dominated using the techniques used so effectively against the Aztecs and the Inca. The swampy lowlands impeded the expedition particularly when...There’ s a marble down here. (MC) 1 It’s a marble I thought it was a bird egg. It nmust’ve been one of Wilards when he was a kid I guess. (CR) g Oh God ...plaster. (BL) Probably since. (CR) I What I think it is; Bob the sun has baked it out and stuff. (MC) U It’% probably made out of lime. (CR) Yea thats what

11. Detail of the interior, looking through an interior doorway ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. Detail of the interior, looking through an interior doorway toward the front and east window. Note: This photograph shows that the building had been converted to a residence following its use as a school. In addition, the hazardous condition of the structure's interior is evident. Two ceilings which are visible in the photograph, (the upper, probably original plastered ceiling, and a secondary, adapted ceiling) as well as ceiling joists in the southernmost rooms have collapsed. Because of the dangerous condition of the interior of the building, additional interior photography was not attempted at this time. - Perry Township School No. 3, Middle Mount Vernon & Eickhoff Roads, Evansville, Vanderburgh County, IN

Repair and Strengthening by Use of Superficial Fixed Laminates of Cracked Masonry Walls Sheared Horizontally-Laboratory Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kubica, Jan; Kwiecien, Arkadiusz; Zajac, Boguslaw

2008-07-08

There are many methods of crack repairing in masonry structures. One of them is repair and strengthening by using of superficial fixed laminates, especially in case of masonry walls with plastering on their both sides. The initial laboratory tests of three different types of strengthening of diagonal cracked masonry wallettes are presented. Tests concerned three clay brick masonry walls subjected to horizontal shearing with two levels of precompression and strengthened by flexible polymer injection, superficial glass fixed by polymer fibre laminate plates and using of CRFP strips stiff fixed to the wall surface by polymer and stiff resin epoxy fixingmore » are presented and discussed.« less

Hypomelanosis of Ito presenting with pediatric orthopedic issues: a case report.

PubMed

Trägårdh, Malene; Thomsen, Christine Rohr; Thorninger, Rikke; Møller-Madsen, Bjarne

2014-05-19

Hypomelanosis of Ito was originally described as a purely cutaneous disease. Extracutaneous manifestations were described later, forming a neurocutaneous syndrome including skeletal, muscular, ocular and central nervous system symptoms.Hypomelanosis of Ito is characterized by a depigmentation along the lines of Blaschko on the trunk and extremities in certain patterns.The aim of this article was to report another case and give an overview of the related orthopedic symptoms that have been previously described. It was also our wish to contribute with recommendations for consideration with regard to bandages on eczematous rashes, especially on clubfeet. A one-and-a-half-month-old boy of Caucasian background born with talipes equinovarus, or clubfoot, on his right foot presented with an eczematous rash after surgical correction and plaster bandaging. It is the appearance of hypopigmentation, either alone or in combination with a congenital malformation, particularly central nervous system or musculoskeletal anomalies, which should form the basis of a presumptive diagnosis. This should then lead to further investigations and should always include skin biopsies and a test for chromosomal mosaicism.We report the case of a boy with a clinical picture consisting of a depigmented skin pattern, mental retardation, pes cavus, talipes equinovarus, clinodactyly, eczema, inverted cilia of the eye, strabismus, reduced hearing, ventral hernia, glomerulonephritis, missing testicles, leg length discrepancy with scoliosis, back pain and a syrinx.It is perhaps impossible to make any conclusions about extracutaneous symptoms. However, some symptoms such as retardation, cramps and seizures, delayed development and hypotonia cannot be ignored.Because of the possibility of creating an undesirable and long postoperative period with complications, it is very important to have this diagnosis in mind when deciding to do surgery or not if there are signs of dermatological problems before surgery. In this case, it could also be good clinical practice to test the patient's reaction to plaster or other bandages.

Neuropathic low back pain in clinical practice.

PubMed

Baron, R; Binder, A; Attal, N; Casale, R; Dickenson, A H; Treede, R-D

2016-07-01

Low back pain (LBP) is one of the most common chronic pain conditions. This paper reviews the available literature on the role of neuropathic mechanisms in chronic LBP and discusses implications for its clinical management, with a particular focus on pharmacological treatments. Literature searches were performed in PubMed, key pain congresses and ProQuest Dialog to identify published evidence on neuropathic back pain and its management. All titles were assessed for relevant literature. Chronic LBP comprises both nociceptive and neuropathic components, however, the neuropathic component appears under-recognized and undertreated. Neuropathic pain (NP) is challenging to manage. Many patients with chronic LBP have pain that is refractory to existing treatments. Typically, less than half of patients experience clinically meaningful analgesia with oral pharmacotherapies; these are also associated with risks of adverse effects. Paracetamol and NSAIDs, although widely used for LBP, are unlikely to ameliorate the neuropathic component and data on the use of NP medications such as antidepressants and gabapentin/pregabalin are limited. While there is an unmet need for improved treatment options, recent data have shown tapentadol to have efficacy in the neuropathic component of LBP, and studies suggest that the capsaicin 8% patch and lidocaine 5% medicated plaster, topical analgesics available for the treatment of peripheral NP, may be a valuable additional approach for the management of neuropathic LBP. Chronic LBP often has an under-recognized neuropathic component, which can be challenging to manage, and requires improved understanding and better diagnosis and treatment. WHAT DOES THIS REVIEW ADD?: Increased recognition and improved understanding of the neuropathic component of low back pain raises the potential for the development of mechanism-based therapies. Open and retrospective studies suggest that agents like tapentadol and topical analgesics - such as the capsaicin 8% patch and the lidocaine 5% medicated plaster - may be effective options for the treatment of neuropathic low back pain in defined patient groups. © 2016 The Authors. European Journal of Pain published by John Wiley & Sons Ltd on behalf of European Pain Federation - EFIC®.

[Evaluating the accuracy of three-dimensional reconstruction of the intercuspal position for dentition casts aided by a mechanical appliance].

PubMed

Hu, Z W; Li, W W; Zhang, X Y; Fan, B L; Wang, Y; Sun, Y C

2016-08-01

To develop a aided mechanical appliance for rapid reconstruction of three-dimensional(3D)relationship of dentition model after scanning and evaluation of its accuracy. The appliance was designed by forward engineering software and fabricated by a high precision computer numerical control(CNC)system. It contained upper and lower body, magnetic pedestal and three pillars. Nine 3 mm diameter hemispheres were distributed equally on the axial surface of each pedestal. Faro Edge 1.8m was used to directly obtain center of each hemisphere(contact method), defined as known center. A pair of die-stone standard dentition model were fixed in intercuspal position and then fixed on the magnetic pedestals with low expansion ratio plaster. Activity 880 dental scanner was used to scan casts after the plaster was completely set. In Geomagic 2012, the centers of each hemisphere were fitted and defined as scanning centers. Scanning centers were aligned to known centers by reference point system to finish the 3D reconstruction of the intercuspal occlusion for the dentition casts. An observation coordinate system was interactively established. The straight-line distances in the X(coronal), Y(saggital), and Z(vertical)between the remaining 6 pairs of center points derived from contact method and fitting method were measured respectively and analyzed using a paired t-test. The differences of the straight-line distances of the remaining 6 pairs of center points between the two methods were X:(-0.05±0.10)mm, Y:(0.02±0.06)mm, and Z:(0.01 ± 0.05)mm. The results of paired t-test showed no significant differences(P>0.05). The mechanical appliance can help to reconstruct 3D jaw relation by scanning single upper and lower dentition model with usual commercial available dental cast scanning system.

Interpretation of architecture changes by combined use of historical sources, IR Termography and GPR: the study case of San Francesco convent near Montella (AV), Italy

NASA Astrophysics Data System (ADS)

Geraldi, Edoardo; Loperte, Antonio; Dolce, Carmen

2010-05-01

In order to reconstruct architectural changes during the centuries often we are forced to trust merely on the evidences of documentary and iconographical sources which could sometimes supply the description of the monument or of a specifically building phase. Such approach does not solve all the questions related to the interpretation of historical data (graphics, descriptions) useful for finding previous configurations of the building. The historical building structure and shape, as they appear at the present are often the final result of a stratification of different phases deeply connected with artistic and technological features of the age during which the building has been designed and realized. Stylistic features, building techniques and functional aspects change in time leaving often written traces in archive sources such as on the building masonry texture (sometimes hidden by plaster) or under the floor. In such situation the Non Destructive Testing investigations by means of infrared thermography and GPR could be useful to characterize masonry, to survey inhomogeneities in the masonry as well as to detect buried walls belongings to ancient building phases. This paper deals with the emblematic study case of San Francisco convent near Montella in Southern Italy. Its complex vicissitudes experienced in last centuries have been the reason of radical transformations of the church and its surrounding buildings. Historical research provided important information on structural interventions and planimetric transformations carried out between the 17th and 18th century. Such data have been correlated with the results obtained by infrared thermography surveys on plastered facades of the convent and GPR profiles carried out under the stone paved floor of the church and cloister, thus improving the knowledge of historical building phases of the monument. The integrated use of building analysis techniques based on NDT techniques together with historical and archaeological records show the enormous potential of the use of this interdisciplinary approach.

Marginal adaptation of full-coverage CAD/CAM restorations: in vitro study using a non-destructive method.

PubMed

Romeo, E; Iorio, M; Storelli, S; Camandona, M; Abati, S

2009-03-01

Marginal fit of full-coverage crowns is a major requirement for long term success of this kind of restorations. The purpose of the study was to verify the marginal adaptation of computer assisted design (CAD)/computer assisted manufacturing (CAM) crowns on prepared teeth and on plaster dies. Four couples of materials: zirconia-ceramic veneering (DC-Zircon, DCS Dental, Allschwill, CH/Cercon S, Degussa, DeguDent GmbH, Hanau, Germany), fiber-reinforced composite-composite veneering (DC-Tell, DCS Dental/Gradia, GC Europe, LEuven, Belgium), titanium-ceramic veneering (DC Titan, DCS Dental/Tikrom, Orotig, Verona, Italy) and titanium-composite veneering (DC Titan, DCS Dental/Gradia, GC Europe) were evaluated following the guidelines provided by ADA specific #8. Five crowns were fabricated for each material. Marginal gap values were measured at four points (0 degrees, 90 degrees, 180 degrees and 270 degrees starting from the centre of the vestibular surface) around the finishing line, on prepared teeth and on plaster dies at each step of the fabrication process. Digital photographs were taken at each reference point and a computer software was used to measure the amount of marginal discrepancy in microm. Statistical analysis was performed using t test at 95 percent confidence interval. All the tested materials, except for fiber-reinforced composite, show a marginal adaptation within the limits of ADA specification (25-40 microm). The application of veneering material causes decay in marginal adaptation, except for fiber-reinforced composite. Within the limitations of this study, it was concluded that marginal fit of CAD/CAM restoration is within the limits considered clinically acceptable by ADA specification #8. From the results of this in vitro study, it can be stated that CAD/CAM crowns produced with DCS system show a marginal adaptation within the limits of ADA specific #8, therefore milled CAD/CAM crowns can be considered a good alternative to more traditional waxing-investing-casting technique.

Monkey vocal tracts are speech-ready.

PubMed

Fitch, W Tecumseh; de Boer, Bart; Mathur, Neil; Ghazanfar, Asif A

2016-12-01

For four decades, the inability of nonhuman primates to produce human speech sounds has been claimed to stem from limitations in their vocal tract anatomy, a conclusion based on plaster casts made from the vocal tract of a monkey cadaver. We used x-ray videos to quantify vocal tract dynamics in living macaques during vocalization, facial displays, and feeding. We demonstrate that the macaque vocal tract could easily produce an adequate range of speech sounds to support spoken language, showing that previous techniques based on postmortem samples drastically underestimated primate vocal capabilities. Our findings imply that the evolution of human speech capabilities required neural changes rather than modifications of vocal anatomy. Macaques have a speech-ready vocal tract but lack a speech-ready brain to control it.

XRF and UV-Vis-NIR analyses of medieval wall paintings of al-Qarawiyyin Mosque (Morocco)

NASA Astrophysics Data System (ADS)

Fikri, I.; El Amraoui, M.; Haddad, M.; Ettahiri, A. S.; Bellot-Gurlet, L.; Falguères, C.; Lebon, M.; Nespoulet, R.; Ait Lyazidi, S.; Bejjit, L.

2018-05-01

Medieval wall painting fragments, taken at the medieval Mosque of al-Qarawiyyin in Fez, have been investigated by means of X-ray fluorescence and UV-Vis-NIR diffuse reflectance spectroscopies. The analyses permitted to determine the palette of pigments used by craftsmen of the time. Hematite or red ochre were used to obtain red brown colours, calcite for white, copper-based pigments for blue and blue-grey shades while a mixture of cinnabar, lead-based pigments and hematite was adopted to make red-orange colours. Furthermore, the analysis of mortars (external layer and plaster) on these wall painting samples revealed that they are composed mainly by calcite and sometimes by additional compounds such as quartz and gypsum.

[Murder of the mother by the daughter--family dynamics and mythology].

PubMed

Klosinski, G

1996-01-01

The comprehensive casuistry, which is based on the forensic examination by the author illustrates a family-drama, in which a 19-year-old girl killed her alcohol and tablet dependent mother in multiple ways and later, with the help of the three years younger sister plastered the body in a sarcophagus inside the apartment. The paper will delineate the life-circumstances, the family- and the psychodynamic of the criminal act. Beside a review of the literature concerning matricide by the daughter, the dynamic aspect of the matricide will be discussed on the basis of the greek tragedies Elektra (Sophokles) and Medea (Euripides). The victim is compared with the part of Medea, the fate of the daughter with the fate of Elektra.

A new postoperative otoplasty dressing technique using cyanoacrylate tissue adhesives.

PubMed

Vetter, Miriam; Foehn, Matthias; Wedler, Volker

2010-04-01

There are many techniques for cosmetic surgery of the ears and also many different procedures for postoperative treatment. The postoperative dressing is described as important for a successful outcome. We present our method of postoperative dressing in the form of liquid bonding. Cyanoacrylate tissue adhesives as liquid bonding agents are used for fixation of the pinna at the mastoid area. After 10-14 days the bonding can be easily removed. No huge dressings, tapes, or plasters are necessary. The patients are satisfied with the light dressing; they do not feel ashamed to appear in public. We have found this dressing technique to be simple and economical, especially because of the use of the bonding for skin closure before. It can be used after otoplasty with an anterior or a posterior approach.

X-ray computed tomography datasets for forensic analysis of vertebrate fossils.

PubMed

Rowe, Timothy B; Luo, Zhe-Xi; Ketcham, Richard A; Maisano, Jessica A; Colbert, Matthew W

2016-06-07

We describe X-ray computed tomography (CT) datasets from three specimens recovered from Early Cretaceous lakebeds of China that illustrate the forensic interpretation of CT imagery for paleontology. Fossil vertebrates from thinly bedded sediments often shatter upon discovery and are commonly repaired as amalgamated mosaics grouted to a solid backing slab of rock or plaster. Such methods are prone to inadvertent error and willful forgery, and once required potentially destructive methods to identify mistakes in reconstruction. CT is an efficient, nondestructive alternative that can disclose many clues about how a specimen was handled and repaired. These annotated datasets illustrate the power of CT in documenting specimen integrity and are intended as a reference in applying CT more broadly to evaluating the authenticity of comparable fossils.

The chopstick-noodle twist: an easy technique of percutaneous patellar fixation in minimally displaced patellar fractures.

PubMed

Muzaffar, Nasir; Ahmad, Nawaz; Ahmad, Aejaz; Ahmad, Nissar

2012-01-01

We report six cases of minimally displaced two-part patellar fractures with skin injury over the patella that were treated with percutaneous K wire fixation and compression applied using stainless steel (SS) wire. This technique makes it possible to perform early operative treatment in cases where unhealthy skin is not amenable to conventional tension band wiring. The technique employs two K wires inserted through the two fracture fragments under local or regional anaesthesia. They are then compressed using simple SS wire knots at the two ends - making it look like noodles at the end of two chopsticks. The fixation is subsequently augmented with a cylindrical plaster-of-Paris cast. The technique is simple, cheap and does not cause soft tissue injury.

Micro-attenuated total reflection spectral imaging in archaeology: application to Maya paint and plaster wall decorations.

PubMed

Goodall, Rosemary A; Hall, Jay; Sharer, Robert J; Traxler, Loa; Rintoul, Llew; Fredericks, Peter M

2008-01-01

Fourier transform infrared (FT-IR) attenuated total reflection (ATR) imaging has been successfully used to identify individual mineral components of ancient Maya paint. The high spatial resolution of a micro FT-IR-ATR system in combination with a focal plane array detector has allowed individual particles in the paint to be resolved and identified from their spectra. This system has been used in combination with micro-Raman spectroscopy to characterize the paint, which was found to be a mixture of hematite and silicate particles with minor amounts of calcite, carbon, and magnetite particles in a sub-micrometer hematite and calcite matrix. The underlying stucco was also investigated and found to be a combination of calcite with fine carbon particles, making a dark sub-ground for the paint.

Quantitative analysis of pulse thermography data for degradation assessment of historical buildings

NASA Astrophysics Data System (ADS)

Di Maio, Rosa; Piegari, Ester; Mancini, Cecilia; Chiapparino, Antonella

2015-06-01

In the last decades, infrared thermography has been successfully applied to various materials and structures for the assessment of their state of conservation and planning suitable restoration works. To this aim, mathematical models are required to characterize thermal anomaly sources, such as detachments, water infiltration and material decomposition processes. In this paper, an algorithm based on the conservative finite difference method is used to analyse pulse thermography data acquired on an ancient building in the Pompeii archaeological site (Naples, Italy). The numerical study is applied to both broad and narrow elongated thermal anomalies. In particular, from the comparison between simulated and experimental thermal decays, the plaster thickness was characterized in terms of thermal properties and areas of possible future detachments, and moisture infiltration depths were identified.

PSEUDARTHROSIS OF THE SCAPHOID IN IMMATURE SKELETONS

PubMed Central

de Lemos, Marcelo Barreto; Bentes, Ádria Simone Ferreira; Neto, Miguel Flores do Amaral; Spinelli, Leandro de Freitas; Severo, Antônio Lourenço; Lech, Osvandré

2015-01-01

This paper presents a review of the literature on pseudarthrosis of the scaphoid in skeletally immature individuals, taking into consideration its epidemiology, diagnosis and treatment, as well as its controversies. Knowledge of this subject makes it possible for patients to be given appropriate treatment immediately. Pseudarthrosis of the scaphoid in skeletally immature patients is a rare condition that results from error or lack of diagnosis of a fracture. Thus, careful clinical and radiographic examination should be performed in order to confirm or rule out this diagnosis. Several treatment methods have been reported and have shown good results. These include conservative plaster cast treatment, bone graft without osteosynthesis, bone graft with Kirschner wires, percutaneous screws and bone graft with compression screws. The treatment performed depends on the characteristics of the pseudarthrosis and the surgeon's experience. PMID:27042636

PSEUDARTHROSIS OF THE SCAPHOID IN IMMATURE SKELETONS.

PubMed

de Lemos, Marcelo Barreto; Bentes, Ádria Simone Ferreira; Neto, Miguel Flores do Amaral; Spinelli, Leandro de Freitas; Severo, Antônio Lourenço; Lech, Osvandré

2012-01-01

This paper presents a review of the literature on pseudarthrosis of the scaphoid in skeletally immature individuals, taking into consideration its epidemiology, diagnosis and treatment, as well as its controversies. Knowledge of this subject makes it possible for patients to be given appropriate treatment immediately. Pseudarthrosis of the scaphoid in skeletally immature patients is a rare condition that results from error or lack of diagnosis of a fracture. Thus, careful clinical and radiographic examination should be performed in order to confirm or rule out this diagnosis. Several treatment methods have been reported and have shown good results. These include conservative plaster cast treatment, bone graft without osteosynthesis, bone graft with Kirschner wires, percutaneous screws and bone graft with compression screws. The treatment performed depends on the characteristics of the pseudarthrosis and the surgeon's experience.

Effect of Reynolds number on flow and mass transfer characteristics of a 90 degree elbow

NASA Astrophysics Data System (ADS)

Fujisawa, Nobuyuki; Ikarashi, Yuya; Yamagata, Takayuki; Taguchi, Syoichi

2016-11-01

The flow and mass transfer characteristics of a 90 degree elbow was studied experimentally by using the mass transfer measurement by plaster dissolution method, the surface flow visualization by oil film method and stereo PIV measurement. The experiments are carried out in a water tunnel of a circular pipe of 56mm in diameter with a working fluid of water. The Reynolds number was varied from 30000 to 200000. The experimental result indicated the change of the mass transfer coefficient distribution in the elbow with increasing the Reynolds number. This phenomenon is further examined by the surface flow visualization and measurement of secondary flow pattern in the elbow, and the results showed the suggested change of the secondary flow pattern in the elbow with increasing the Reynolds numbers.

Neutron Spectrometry for Identification of filler material in UXO - Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bliss, Mary

2007-09-12

Unexploded ordnance (UXO)-contaminated sites often include ordnance filled with inert substances that were used in dummy rounds. During UXO surveys, it is difficult to determine whether ordnance is filled with explosives or inert material (e.g., concrete, plaster-of-paris, wax, etc.) or is empty. Without verification of the filler material, handling procedures often necessitate that the object be blown in place, which has potential impacts to the environment, personnel, communities and survey costs. The Department of Defense (DoD) needs a reliable, timely, non-intrusive and cost-effective way to identify filler material before a removal action. A new technology that serves this purpose wouldmore » minimize environmental impacts, personnel safety risks and removal costs; and, thus, would be especially beneficial to remediation activities.« less

Glucocorticoid sensitivity, disuse, and the regulation of muscle mass

NASA Technical Reports Server (NTRS)

Almon, R. R.; Dubois, D. C.

1983-01-01

A new noninvasive immobilization procedure to be used on rats has been developed to study immobilization-induced muscle hypersensitivity to normal glucocorticoid concentration, subsequent muscle atrophy, and atrophy recovery. The immobilization procedure involves encasing the hind limb in a light-weight plasticlike cast (10 percent the usual plaster weight), completely resistant to animal gnawing. The effects of right-angle immobilization of the ankle on the slow fiber soleus, and the fast fiber extensor digitorum longus, resemble the effects of weightlessness. The increased concentration of glucocorticoid receptor sites in immobilized and denervated muscle is discussed, along with the chronic loss of muscle mass that occurs in practically all dystrophies. It is concluded that lack of mechanical work in a zero gravity environment is a major cause of glucocorticoid hypersensitivity in the body's musculature.

Surgical results of leg amputation according to Ghormley's technique in the treatment of chronic lower limb ischaemia.

PubMed

Wasiak, K; Paczkowski, P M; Garlicki, J M

2006-01-01

The authors present their experience in the treatment of chronic lower limb ischaemia resulting from atherosclerosis by below knee amputation according to Ghormley's technique, with the immediate application of a semi-rigid plaster cast and early rehabilitation. From a group of 664 patients requiring major amputations, 61 patients (52 men) aged 64 +/- 11 fulfilled the criteria for unilateral below-knee amputation for critical limb ischaemia for atherosclerosis consequences. Peri-operative (30-days) mortality was of 3.28%. Stump healing was very good or good (no need for further surgery) in over 2/3 of patients, but in 20% the need for above-knee amputation developed. Postoperative knee contracture (defined as 15 degrees or more limitation to the movement range) was observed in 11.5% of patients.

X-ray computed tomography datasets for forensic analysis of vertebrate fossils

PubMed Central

Rowe, Timothy B.; Luo, Zhe-Xi; Ketcham, Richard A.; Maisano, Jessica A.; Colbert, Matthew W.

2016-01-01

We describe X-ray computed tomography (CT) datasets from three specimens recovered from Early Cretaceous lakebeds of China that illustrate the forensic interpretation of CT imagery for paleontology. Fossil vertebrates from thinly bedded sediments often shatter upon discovery and are commonly repaired as amalgamated mosaics grouted to a solid backing slab of rock or plaster. Such methods are prone to inadvertent error and willful forgery, and once required potentially destructive methods to identify mistakes in reconstruction. CT is an efficient, nondestructive alternative that can disclose many clues about how a specimen was handled and repaired. These annotated datasets illustrate the power of CT in documenting specimen integrity and are intended as a reference in applying CT more broadly to evaluating the authenticity of comparable fossils. PMID:27272251

Effect of inactivity and passive stretch on protein turnover in phasic and postural rat muscles

NASA Technical Reports Server (NTRS)

Loughna, P.; Goldspink, G.; Goldspink, D. F.

1986-01-01

Muscle atrophy in humans can occur during prolonged bed rest, plaster cast immobilization, and space flight. In the present study, the suspension model used by Musacchia et al. (1983) is employed to investigate changes in protein synthesis and degradation in fast-twitch phasic (extensor digitorum longus) and slow-twitch postural (soleus) muscles in the rat, following hypokinesia and hypodynamia. In addition, the use of passive stretch was examined as a means of preventing atrophy. The obtained results suggest that the mechanisms controlling the processes of protein synthesis and protein breakdown during muscle disuse atrophy may be independent of each other. It appears, however, that the muscle atrophy due to hypokinesia and hypodynamia can be temporarily prevented by passively stretching a muscle.

"Brace Technology" Thematic Series - The ScoliOlogiC® Chêneau light™ brace in the treatment of scoliosis.

PubMed

Weiss, Hans-Rudolf; Werkmann, Mario

2010-09-06

Bracing concepts in use today for the treatment of scoliosis include symmetric and asymmetric hard braces usually made of polyethylene (PE) and soft braces. The plaster cast method worldwide seems to be the most practiced technique for the construction of hard braces at the moment. CAD (Computer Aided Design) systems are available which allow brace adjustments without plaster. Another possibility is the use of the ScoliOlogiC™ off the shelf system enabling the Certified Prosthetist and Orthotist (CPO) to construct a light brace for scoliosis correction from a variety of pattern specific shells to be connected to an anterior and a posterior upright. This Chêneau light™ brace, developed according to the Chêneau principles, promises a reduced impediment of quality of life in the brace. The correction effects of the first 81 patients (main diagnosis Adolescent Idiopathic Scoliosis (AIS) [n = 64] or Early Onset Scoliosis (EOS) [n = 15]), treated according to the principles of the Chêneau light™ brace have shown a satisfactory in-brace correction exceeding 50% of the initial Cobb angle. The ScoliOlogiC® off the shelf bracing system enables the CPO to construct a light brace for scoliosis correction from a variety of pattern specific shells to be connected to an anterior and a posterior upright. This brace, when finally adjusted is called Chêneau light™ brace. The advantage of this new bracing system is that the brace is available immediately, is easily adjustable and that it can also be easily modified. This avoids construction periods of sometimes more than 6 weeks, where the curve may drastically increase during periods of fast growth. The disadvantage of this bracing system is that there is a wide variability of possibilities to arrange the different shells during adjustment. The Cobb angle in the whole group was reduced by an average of 16,4°, which corresponds to a correction effect of 51%. The differences were highly significant in the T-test (T = 17,4; p < 0,001). The best correction effects achieved with Chêneau braces reported in literature so far are about 40% in two different studies. The correction effect was highest in lumbar and thoracolumbar curve patterns (62%; n = 18). In thoracic scoliosis the correction effect was 36% (n = 41) and in double major curve patterns 50% (n = 22). The correction effect was affected in a slightly negative way due to age (r = -0,24; p = 0,014), negatively with the Risser stage (-0,29; p = 0,0096) and correlated negatively with the Cobb angle measured before treatment (r = -0,43; p < 0,0001). The use of the Chêneau light™ brace leads to correction effects above average when compared to correction effects of other braces described in literature. The reduction of material seems to increase patient's comfort and reduces the stress patients may suffer from whilst in the brace.80% of the adolescent population of scoliosis patients can be braced with the Chêneau light™ brace. In certain patterns of curvature and in the younger population with an age of less than 11 years, other approaches have to be used, such as plaster based bracing or the application of CAD/CAM based orthoses.

Visual documentation process of historic building refurbishment "Improving energy efficiency by insulating wall cavity"

NASA Astrophysics Data System (ADS)

Bennadji, A.

2013-07-01

The North East of Scotland's construction method is similar to most popular building typologies in the UK. This typology can vary in term of external material (Granite, brick or stone) but with a secondary, usually timber sub frame with a lining on its interior. Insulation was seldom a consideration when such buildings were completed. Statistics shows that 80% of existing buildings in the UK will need to be upgraded. The lack of knowledge in dealing with old building fabric's manipulation has a negative impact on buildings' integrity. The documentation of such process seems to be an important step that buildings' actors should undertake to communicate a practical knowledge that is still at incubation stage. We wanted for this documentation to be visual, as descriptions might mislead none specialised and specialised in the field due to the innovative approach our method was conducted with. For the Scottish context this research/experiment will concentrate on existing granite wall buildings with plastered lath internal wall. It is unfortunate to see the commonly beautiful interiors of Scottish buildings disappearing, when the internal linings are removed. Skips are filled with old Plaster and Lath and new linings have to be supplied and fitted. Excessive waste is created in this change. This paper is based on a historic building energy improvement case study financed by the European commission and the Scottish Government. The pilot study consists of insulating an 18th century house using an innovative product and method. The project was a response to a call by the CIC start (Construction Innovation Club), aiming to establish a link between SMEs and the Universities. The project saw the day in collaboration with Icynene Canada, KDL Kishorn (see full list in the acknowledgment). This paper describes the process through which the team went through to improve the building envelope without damaging the buildings original features (Loveday et all). The energy efficiency improvement consists on improving the walls U-val by introducing an insulation material Icynene (Sadineni, France & Boehm 2011) into the cavity wall. The U-val was improved by 50% and no redecoration was needed after the operation and no disturbance to the building's occupants.

Geomorphology of the Eastern North American Continental Margin: the role of deep sea sedimentation processes

NASA Astrophysics Data System (ADS)

Mosher, D. C.; Campbell, C.; Piper, D.; Chaytor, J. D.; Gardner, J. V.; Rebesco, M.

2016-12-01

Deep-sea sedimentation processes impart a fundamental control on the morphology of the western North Atlantic continental margin from Blake Spur to Hudson Strait. This fact is illustrated by the variable patterns of cross-margin gradients that are based on extensive new multibeam echo-sounder data in concert with subbottom profiler and seismic reflection data. Most of the continental margin has a steep (>3o) upper slope down to 1500 to 2500 m and then a gradual middle and lower slope with a general concave upward shape There is a constant interplay of deep sea sedimentation processes, but the general morphology is dictated by the dominant one. Erosion by off-shelf sediment transport in turbidity currents creating channels, gullies and canyons creates the steep upper slope. These gullies and canyons amalgamate to form singular channels that are conduits to the abyssal plain. This process results in a general seaward flattening of gradients, producing an exponentially decaying slope profile. Comparatively, sediment mass failure produces steeper upper slopes due to head scarp development and a wedging architecture to the lower slope as deposits thin in the downslope direction. This process results in either a two-segment slope, and/or a significant downslope gradient change where MTDs pinch out. Large sediment bodies deposited by contour-following currents are developed all along the margin. Blake Ridge, Sackville Spur, and Hamilton Spur are large detached drifts on disparate parts of the margin. Along their crests, they form a linear profile from the shelf to abyssal plain. Deeper portions of the US continental margin are dominated by the Chesapeake Drift and Hatteras Outer Ridge; both plastered elongate mounded drifts. Farther north, particularly on the Grand Banks margin, are plastered and separated drifts. These drifts tend to form bathymetric steps in profile, where they onlap the margin. Stacked drifts create several steps. Turbidites of the abyssal plain onlap the lowermost drift creating a significant gradient change at this juncture. Understanding the geomorphological consequences of deep sea sedimentation processes is important to extended continental shelf mapping, for example, in which gradient change is a critical metric.

[The disease and treatment of the frontline soldiers in Han dynasty].

PubMed

Min, Hookie

2015-04-01

This paper purports to identify and analyze the medical information of the frontline soldiers in the Northwest borderland provinces of Han Dynasty, especially Juyan and Dunhuang region, through an heuristic reading of the Juyan Bamboo Slips and the Dunhuang Bamboo Slips of the Han Dynasty. My findings are as follows. The most frequent disease found in the bamboo slips was the external injury. The injury of the frontline soldiers mainly occurred from the quarrels among armed soldiers using weapons. The bamboo slips also demonstrate that the quarrels usually arose due to the fierce tension caused by the frontier line service such as heavy guard activity and labour duty. Undernourishment and chronic stress the soldiers suffered might be another reasons. The second most common disease harassing the soldiers was exogenous febrile disease. In most cases reviewed in this paper, the exogenous febrile disease was usually concurrent with complex symptoms such as chills, fever, headache, etc. The bamboo slips show that the exogenous febrile disease was related to the harsh climate of the Northwest provinces, featuring extremely dry weather and the large magnitude of diurnal temperature fluctuations. In addition, the annual temperature range in the Northwest province was huge, fluctuating between very cold and dry winter and very hot and dry summer. The third most common disease this study identified was the disorder of the digestive system and respiratory system. However, these two types of disease were virtually indistinguishable in the bamboo slips, because the ancient Chinese chroniclers did not distinguish them, usually dubbing both diseases simply 'abdominal pain.' It should be mentioned that a few slips mention contagious disease such as dysentery and dermatolosis, and sudden death, as well. Overall, the bamboo slips demonstrate extremely poor status of the soldiers' heath condition and poor medical environment surrounding the soldiers stationing in the Northwest borderland military camps. The records also show that acupuncture, applying a plaster, drugs were the most common medical treatment. Drugs among them was the most frequently used. Whereas Acupuncture, applying a plaster were very rarely used. Medication has been used in three ways: powdered medicine, medicinal decoction and pill. Medicinal decoction was the most commonly used way.

Serial elongation, derotation and flexion (EDF) casting under general anesthesia and neuromuscular blocking drugs improve outcome in patients with juvenile scoliosis: preliminary results.

PubMed

Canavese, Federico; Botnari, Alexei; Dimeglio, Alain; Samba, Antoine; Pereira, Bruno; Gerst, Adeline; Granier, Marie; Rousset, Marie; Dubousset, Jean

2016-02-01

Juvenile scoliosis (JS), among different types of spinal deformity, remains still a challenge for orthopedic surgeons. Elongation, derotation and flexion (EDF) casting technique is a custom-made thoracolumbar cast based on a three-dimensional correction concept. The primary objective of the present study was to measure changes on plain radiographs of patients with JS treated with EDF plaster technique. The second aim was to evaluate the effectiveness of the EDF plaster technique realized under general anesthesia (GA) and neuromuscular blocking drugs, i.e. curare, on the radiological curve correction. A retrospective comparative case series study was performed in which were included forty-four skeletally immature patients. Three patient groups were selected. Group 1: EDF cast applied with patients awaken and no anesthesia; Group 2: EDF cast applied under GA without neuromuscular blocking drugs; Group 3: EDF cast applied under GA with neuromuscular blocking drugs. All the patients were treated with two serial EDF casts by 2 months and a half each. All measurements were taken from the radiographic exams. Cobb's angle; RVAD and Nash and Moe grade of rotation were assessed before and after applying the cast. Thirty-four (77.3 %) patients were followed up at least 24 months after removal of last EDF cast. Eighteen patients (3 males, 15 females) were included in Group 1, 12 (2 males, 10 females) in Group 2 and 14 (5 males, 9 females) in Group 3. Serial EDF casting was more effective at initial curve reduction and in preventing curve progression when applied under GA with neuromuscular blocking drugs, i.e. curare. RVAD and Nash and Moe score improved significantly in all groups of patients treated according to principles of EDF technique. During follow-up period, six patients required surgery in Group 1 (6/18; 33.3 %), 3 patients required surgery in Group 2 (3/12; 25 %) and 2 patients underwent surgery in Group 3 (2/14; 15 %). Preliminary results show EDF casting is effective in controlling the curve in both frontal (Cobb's angle) and transverse plane (rib vertebral angle and apical vertebral rotation degree).

Brace technology thematic series - The Sforzesco and Sibilla braces, and the SPoRT (Symmetric, Patient oriented, Rigid, Three-dimensional, active) concept

PubMed Central

2011-01-01

Background Bracing is an effective strategy for scoliosis treatment, but there is no consensus on the best type of brace, nor on the way in which it should act on the spine to achieve good correction. The aim of this paper is to present the family of SPoRT (Symmetric, Patient-oriented, Rigid, Three-dimensional, active) braces: Sforzesco (the first introduced), Sibilla and Lapadula. Methods The Sforzesco brace was developed following specific principles of correction. Due to its overall symmetry, the brace provides space over pathological depressions and pushes over elevations. Correction is reached through construction of the envelope, pushes, escapes, stops, and drivers. The real novelty is the drivers, introduced for the first time with the Sforzesco brace; they allow to achieve the main action of the brace: a three-dimensional elongation pushing the spine in a down-up direction. Brace prescription is made plane by plane: frontal (on the "slopes", another novelty of this concept, i.e. the laterally flexed sections of the spine), horizontal, and sagittal. The brace is built modelling the trunk shape obtained either by a plaster cast mould or by CAD-CAM construction. Brace checking is essential, since SPoRT braces are adjustable and customisable according to each individual curve pattern. Treatment time and duration is individually tailored (18-23 hours per day until Risser 3, then gradual reduction). SEAS (Scientific Exercises Approach to Scoliosis) exercises are a key factor to achieve success. Results The Sforzesco brace has shown to be more effective than the Lyon brace (matched case/control), equally effective as the Risser plaster cast (prospective cohort with retrospective controls), more effective than the Risser cast + Lyon brace in treating curves over 45 degrees Cobb (prospective cohort), and is able to improve aesthetic appearance (prospective cohort). Conclusions The SPoRT concept of bracing (three-dimensional elongation pushing in a down-up direction) is different from the other corrective systems: 3-point, traction, postural, and movement-based. The Sforzesco brace, being comparable to casting, may be the best brace for the worst cases. PMID:21554719

Coral Reef Response to Marine Isotope Stage (MIS) 5e Sea Level Changes in the Granitic Seychelles

NASA Astrophysics Data System (ADS)

Vyverberg, K.; Dechnik, B.; Dutton, A.; Webster, J.; Zwartz, D.

2015-12-01

Sea-level position has a direct control on coral reef morphology and composition. Examining changes in these parameters in fossil reefs can inform reconstructions of past sea-level behavior and, indirectly, ice sheet dynamics. Here we provide a detailed examination of fossil reefs from Marine Isotope Stage (MIS) 5e. These fossil reefs are located in the granitic Seychelles, which is tectonically stable site and far-field from the former margins of Northern Hemisphere ice sheets. To reconstruct relative sea level (RSL), we combine RTK and Total Station elevation surveys with sedimentary and taxonomic evaluations of eight fossil reef sites. Carbonate coralgal reef buildups of the shallowest portion of the reef are preserved in limestone outcrops that are protected by granite boulder overhangs. Two primary outcrop morphologies were observed at these sites: plastering and massive. Plastering outcrops manifest as thin (~ 1 m height x 1 m width x 0.5 m depth) vertical successions of reef framework and detritus, while massive outcrops are larger (~ 2-6 m height x 2-6 m width x 1-2 m depth). The base of these limestone outcrops consistently record a period of reef growth, characterized by corals or coralline algae colonizing the surface or face of a granite boulder and building upwards. This lower reefal unit is capped by a disconformity that is commonly overlain by coral rubble or a ~10 cm thick layer of micrite. Rubble units contain coarse fragments of the coralgal reef buildups while micrite layers consist of a relatively homogeneous fine-grained carbonate, bearing coral-dwelling, Pyrgomatid barnacles. In many of the outcrops, this succession is repeated upsection with another unit of coralgal reef framework capped by a disconformity that is recognized by the sharp transition to coral rubble or micrite with barnacles. We identified four distinct fossil coralgal assemblages in the limestone outcrops. These assemblages are consistent with modern assemblages which constrain the paleo-water depth histories at each site. The combination of reef taxonomy as well as accretion hiatuses provides robust control on the reef, and thus sea-level, history of this region, and by extension, global mean sea level, during MIS 5e.

A Method of Three-Dimensional Recording of Mandibular Movement Based on Two-Dimensional Image Feature Extraction

PubMed Central

Li, Zhongke; Yang, Huifang; Lü, Peijun; Wang, Yong; Sun, Yuchun

2015-01-01

Background and Objective To develop a real-time recording system based on computer binocular vision and two-dimensional image feature extraction to accurately record mandibular movement in three dimensions. Methods A computer-based binocular vision device with two digital cameras was used in conjunction with a fixed head retention bracket to track occlusal movement. Software was developed for extracting target spatial coordinates in real time based on two-dimensional image feature recognition. A plaster model of a subject’s upper and lower dentition were made using conventional methods. A mandibular occlusal splint was made on the plaster model, and then the occlusal surface was removed. Temporal denture base resin was used to make a 3-cm handle extending outside the mouth connecting the anterior labial surface of the occlusal splint with a detection target with intersecting lines designed for spatial coordinate extraction. The subject's head was firmly fixed in place, and the occlusal splint was fully seated on the mandibular dentition. The subject was then asked to make various mouth movements while the mandibular movement target locus point set was recorded. Comparisons between the coordinate values and the actual values of the 30 intersections on the detection target were then analyzed using paired t-tests. Results The three-dimensional trajectory curve shapes of the mandibular movements were consistent with the respective subject movements. Mean XYZ coordinate values and paired t-test results were as follows: X axis: -0.0037 ± 0.02953, P = 0.502; Y axis: 0.0037 ± 0.05242, P = 0.704; and Z axis: 0.0007 ± 0.06040, P = 0.952. The t-test result showed that the coordinate values of the 30 cross points were considered statistically no significant. (P<0.05) Conclusions Use of a real-time recording system of three-dimensional mandibular movement based on computer binocular vision and two-dimensional image feature recognition technology produced a recording accuracy of approximately ± 0.1 mm, and is therefore suitable for clinical application. Certainly, further research is necessary to confirm the clinical applications of the method. PMID:26375800

Nadroparin or fondaparinux versus no thromboprophylaxis in patients immobilised in a below-knee plaster cast (PROTECT): A randomised controlled trial.

PubMed

Bruntink, Marlieke M; Groutars, Yannick M E; Schipper, Inger B; Breederveld, Roelf S; Tuinebreijer, Wim E; Derksen, Robert J

2017-04-01

The immobilisation of the lower leg is associated with deep vein thrombosis (DVT). However, thromboprophylaxis in patients with a below-knee plaster cast remains controversial. We examined the efficacy and safety of nadroparin and fondaparinux to ascertain the need for thromboprophylaxis in these patients. PROTECT was a randomised, controlled, single-blind, multicentre study that enrolled adults with an ankle or foot fracture who required immobilisation for a minimum of four weeks. The patients were randomly assigned (1:1:1) to a control group (no thromboprophylaxis) or to one of the intervention groups: daily subcutaneous self-injection of either nadroparin (2850 IE anti-Xa=0.3ml) or fondaparinux (2.5mg=0.5ml). A venous duplex sonography was performed after the removal of the cast or earlier if thrombosis was suspected. The primary outcome was the relative risk of developing DVT in the control group compared with that in both intervention groups. This trial is registered at ClinicalTrials.gov, number NCT00881088. Between April 2009 and December 2015, 467 patients were enrolled and assigned to either the nadroparin group (n=154), the fondaparinux group (n=157), or the control group (n=156). A total of 273 patients (92, 92, and 94 patients, respectively) were analysed. The incidence of DVT in the nadroparin group was 2/92 (2.2%) compared with 11/94 (11.7%) in the control group, with a relative risk of 5.4 (95% CI 1.2-23.6; p=0.011). The incidence of DVT in the fondaparinux group was 1/92 (1.1%), yielding a relative risk of 10.8 (95% CI 1.4-80.7; p=0.003) compared with that in the control group. No major complications occurred in any group. Thromboprophylaxis with nadroparin or fondaparinux significantly reduces the risk of DVT in patients with an ankle or foot fracture who were treated in a below-knee cast without any major adverse events. Copyright © 2017 Elsevier Ltd. All rights reserved.

Analysis of the eukaryotic community and metabolites found in clay wall material used in the construction of traditional Japanese buildings.

PubMed

Kitajima, Sakihito; Kamei, Kaeko; Nishitani, Maiko; Sato, Hiroyuki

2010-01-01

Clay wall (tsuchikabe in Japanese) material for Japanese traditional buildings is manufactured by fermenting a mixture of clay, sand, and rice straw. The aim of this study was to understand the fermentation process in order to gain insight into the ways waste biomass can be used to produce useful materials. In this study, in addition to Clostridium, we suggested that the family Nectriaceae and the Scutellinia sp. of fungi were important in degrading cell wall materials of rice straw, such as cellulose and/or lignin. The microorganisms in the clay wall material produced sulfur-containing inorganic compounds that may sulfurate minerals in clay particles, and polysaccharides that give viscosity to clay wall material, thus increasing workability for plastering, and possibly giving water-resistance to the dried clay wall.

Quiet breathing in hindlimb casted mice.

PubMed

Receno, Candace N; Roffo, Katelynn E; Mickey, Marisa C; DeRuisseau, Keith C; DeRuisseau, Lara R

2018-06-07

The hindlimb casting model was developed to study skeletal muscle reloading following a period of unloading. It is unknown if ventilation parameters of mice are affected by the casting model. We tested the hypothesis that hindlimb casted mice have similar ventilatory patterns compared to mice with the casts removed. Male CD-1 mice underwent 14 days of hindlimb immobilization via plaster casting. Breathing parameters were obtained utilizing unrestrained barometric plethysmography (UBP). Breathing traces were analyzed with Ponemah software for breathing frequency, tidal volume (TV), and minute ventilation (MV). Frequency, TV and MV did not show any differences in quiet breathing patterns during or post-casting in mice. Thus, the hindlimb casting model does not complicate breathing during and after casting and should not interfere with the unloading and reloading of skeletal muscle. Copyright © 2018 Elsevier B.V. All rights reserved.

Drug use to resistance exercise-induced fatigue based on diclofenac diethylamine emulgel efficacy analysis.

PubMed

Gu, Qi

2017-05-01

In this paper, the author study on the effect of drug treatment on sports injury, and makes a comparative analysis of drug effects. In sports, the incidence of various types of injuries is increasing, especially in muscle injury. In the experiment, we compared the effects of three different drugs on the treatment and relief of muscle loss. After 3 weeks, the average optical density of desmin in muscle fiber positive region have decreased, as xiaotong plaster (0.4708±0.0126), votalin (0.5124±0.0264) and placebo (0.3856±0.0312). It has a certain effect to promote the repair and regeneration of desmin expression by drugs. Through the analysis of the effect of drug intervention on sports injury repair, we can effectively improve the therapeutic effect of sports injury.

Towards proteomic analysis of milk proteins in historical building materials

NASA Astrophysics Data System (ADS)

Kuckova, S.; Crhova, M.; Vankova, L.; Hnizda, A.; Hynek, R.; Kodicek, M.

2009-07-01

The addition of proteinaceous binders to mortars and plasters has a long tradition. The protein additions were identified in many sacral and secular historical buildings. For this method of peptide mass mapping, three model mortar samples with protein additives were prepared. These samples were analysed fresh (1-2 weeks old) and after 9 months of natural ageing. The optimal duration of tryptic cleavage (2 h) and the lowest amount of material needed for relevant analysis of fresh and weathered samples were found; the sufficient amounts of weathered and fresh mortars were set to 0.05 and 0.005 g. The list of main tryptic peptides coming from milk additives (bovine milk, curd, and whey), their relative intensities and theoretical amino acid sequences assignment is presented. Several sequences have been "de novo" confirmed by mass spectrometry.

Chapel of cemetery church of all saints in Sedlec - Long-term analysis of hygrothermal conditions

NASA Astrophysics Data System (ADS)

Pavlík, Zbyšek; Balík, Lukáš; Kudrnáčová, Lucie; Maděra, Jiří; Černý, Robert

2017-07-01

In this paper, long-term monitoring of hygrothermal conditions of the chapel of the cemetery church of All Saints in Sedlec, Czech Republic is presented as a practical tool for evaluation of functional problems of the researched structure. Within the performed experimental tests, interior and exterior climatic conditions were monitored over one year period. Herewith, surface temperature of the chapel wall was measured. Exterior climatic data were collected using weather station Vantage Pro2 placed in church tower. In interior, precise combined relative humidity/temperature sensors were installed. Based on the accessed hygrothermal state of the inspected chapel and identified periods of possible surface condensation, service conditions of the chapel will be optimized in order to prevent extensive damage of historically valuable finishing and furnishing materials, paintings, plasters, and architectural ornaments.

Effect of Moisture Content on Thermal Properties of Porous Building Materials

NASA Astrophysics Data System (ADS)

Kočí, Václav; Vejmelková, Eva; Čáchová, Monika; Koňáková, Dana; Keppert, Martin; Maděra, Jiří; Černý, Robert

2017-02-01

The thermal conductivity and specific heat capacity of characteristic types of porous building materials are determined in the whole range of moisture content from dry to fully water-saturated state. A transient pulse technique is used in the experiments, in order to avoid the influence of moisture transport on measured data. The investigated specimens include cement composites, ceramics, plasters, and thermal insulation boards. The effect of moisture-induced changes in thermal conductivity and specific heat capacity on the energy performance of selected building envelopes containing the studied materials is then analyzed using computational modeling of coupled heat and moisture transport. The results show an increased moisture content as a substantial negative factor affecting both thermal properties of materials and energy balance of envelopes, which underlines the necessity to use moisture-dependent thermal parameters of building materials in energy-related calculations.

Empathy, but not mimicry restriction, influences the recognition of change in emotional facial expressions.

PubMed

Kosonogov, Vladimir; Titova, Alisa; Vorobyeva, Elena

2015-01-01

The current study addressed the hypothesis that empathy and the restriction of facial muscles of observers can influence recognition of emotional facial expressions. A sample of 74 participants recognized the subjective onset of emotional facial expressions (anger, disgust, fear, happiness, sadness, surprise, and neutral) in a series of morphed face photographs showing a gradual change (frame by frame) from one expression to another. The high-empathy (as measured by the Empathy Quotient) participants recognized emotional facial expressions at earlier photographs from the series than did low-empathy ones, but there was no difference in the exploration time. Restriction of facial muscles of observers (with plasters and a stick in mouth) did not influence the responses. We discuss these findings in the context of the embodied simulation theory and previous data on empathy.

Treatment of posttraumatic deformities in the radiocarpal joint in children.

PubMed

Doletsky, S J; Kiselev, V P

1979-01-01

Experience with treatment of 1885 children with fracture of the forearm bones is reported. Almost 1/3 (28.1%) were patients with epi-osteoepiphysiolysis of the distal end of the radius. In the majority, the method of treatment was conservative: closed manual reposition and immobilization with plaster cast during 3-4 weeks. Closed one-stage reposition is effective only during the first hours of 2-3 days after the trauma. The deformity following an inveterate epi-osteoepiphysiolysis must be corrected surgically before the physiological closure of the growth zones. The pathogenetic problems of posttraumatic deformities in the radiocarpal articulation are discussed and attention is focussed on the "admissible" types of displacement of the epiphysis (meta-epiphysis). The method of bloodless correction of deformities by means of distraction apparatuses is described. The technique was performed in 41 children with good results.

[Assessment of precision and accuracy of digital surface photogrammetry with the DSP 400 system].

PubMed

Krimmel, M; Kluba, S; Dietz, K; Reinert, S

2005-03-01

The objective of the present study was to evaluate the precision and accuracy of facial anthropometric measurements obtained through digital 3-D surface photogrammetry with the DSP 400 system in comparison to traditional 2-D photogrammetry. Fifty plaster casts of cleft infants were imaged and 21 standard anthropometric measurements were obtained. For precision assessment the measurements were performed twice in a subsample. Accuracy was determined by comparison of direct measurements and indirect 2-D and 3-D image measurements. Precision of digital surface photogrammetry was almost as good as direct anthropometry and clearly better than 2-D photogrammetry. Measurements derived from 3-D images showed better congruence to direct measurements than from 2-D photos. Digital surface photogrammetry with the DSP 400 system is sufficiently precise and accurate for craniofacial anthropometric examinations.

Acute closed radial nerve injury

PubMed Central

Tuncel, Umut; Turan, Aydin; Kostakoglu, Naci

2011-01-01

We present a 45-year-old patient who had acute radial nerve palsy following a blunt trauma without any fracture or dislocation. He was injured by strucking in a combat three months ago. The patient has been followed by application of a long-arm plaster cast before referred to our clinic. Preoperative electromyoneurography and magnetic resonance imaging (MRI) indicated that there was a radial nerve injury on humeral groove. The British Medical Research Council (MRC) grade was 2/5 on his wrist preoperatively. The patient underwent an operation under general anesthesia. It was seen to be a second-degree nerve injury. The patient has subsequently regained full movement on his wrist and finger extension in six months. We suggest that a detailed clinical and electrodiagnostical evaluation is necessary in patients who have radial nerve injury when deciding the treatment, conservative or surgical. PMID:22347334

Masonry: Materials, testing, and applications. ASTM special technical publication 1356

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brisch, J.H.; Nelson, R.L.; Francis, H.L.

Masonry is one of mankind's oldest arts. The construction of shelters, buildings, castles, and fortresses has been the life work of untold numbers of artists, architects, masons, plasterers, and laborers. Today people marvel at the ancient structures still standing after hundreds and thousands of years. Works such as the Great Wall of China, The Roman Coliseum, the cathedrals of Europe, and masonry bridges still in use after hundreds of years of wear and tear, encourage us to better understand the art, the mechanics, and the chemistries involved in building and maintaining these structures. In this seminar, the authors attempt tomore » convey their experiences towards a better understanding of the principles and mechanics involved in designing and building masonry structures. The papers presented do just that. Separate abstracts were prepared for most papers.« less

The Rubber Stopper: A Simple and Inexpensive Technique to Prevent Pin Tract Infection following Kirschner Wiring of Supracondylar Fractures of Humerus in Children.

PubMed

Santy, J E; Kamal, J; Abdul-Rashid, A H; Ibrahim, S

2015-07-01

Percutaneous pinning after closed reduction is commonly used to treat supracondylar fractures of the humerus in children. Minor pin tract infections frequently occur. The aim of this study was to prevent pin tract infections using a rubber stopper to reduce irritation of the skin against the Kirschner (K) wire following percutaneous pinning. Between July 2011 and June 2012, seventeen children with closed supracondylar fracture of the humerus of Gartland types 2 and 3 were treated with this technique. All patients were treated with closed reduction and percutaneous pinning and followed up prospectively. Only one patient, who was a hyperactive child, developed pin tract infection due to softening of the plaster slab. We found using the rubber stopper to be a simple and inexpensive method to reduce pin tract infections following percutaneous pinning.

The Rubber Stopper: A Simple and Inexpensive Technique to Prevent Pin Tract Infection following Kirschner Wiring of Supracondylar Fractures of Humerus in Children

PubMed Central

Santy, JE; Abdul-Rashid, AH; Ibrahim, S

2015-01-01

Percutaneous pinning after closed reduction is commonly used to treat supracondylar fractures of the humerus in children. Minor pin tract infections frequently occur. The aim of this study was to prevent pin tract infections using a rubber stopper to reduce irritation of the skin against the Kirschner (K) wire following percutaneous pinning. Between July 2011 and June 2012, seventeen children with closed supracondylar fracture of the humerus of Gartland types 2 and 3 were treated with this technique. All patients were treated with closed reduction and percutaneous pinning and followed up prospectively. Only one patient, who was a hyperactive child, developed pin tract infection due to softening of the plaster slab. We found using the rubber stopper to be a simple and inexpensive method to reduce pin tract infections following percutaneous pinning. PMID:28435603

Supraintercondylar fractures of the humerus--treatment by the Vigliani osteosynthesis.

PubMed

Fama, G

1987-03-01

Nineteen cases of supraintercondylar fractures of the humerus treated by the Vigliani osteosynthesis technique are described. This consists of wide transolecranon exposure of the fracture, stabilisation of the epiphyseal fragments with a transcondylar screw, and of the metaphyseo-epiphyseal junction with two condylo-diaphyseal "Eiffel Tower" Kirschner wires. The ulnar nerve is transposed anteriorly and the operation is carried out early in order to prevent neural disturbances and intra and/or periarticular ossification. The results confirm the validity of this method, which respects the delicate structure of this part of the humerus. Postoperative plaster is necessary as an indispensable complement to "minimum" osteosynthesis but this is quite free from risk. The importance of careful and gradual mobilisation of the elbow is also confirmed. Finally, this method combines the advantages of stable osteosynthesis in compression (screw and nut) at the epiphyseal site, with those of elastic osteosynthesis (Kirschner wires) at the metaphyseo-epiphyseal junction.

[Establishment of database with standard 3D tooth crowns based on 3DS MAX].

PubMed

Cheng, Xiaosheng; An, Tao; Liao, Wenhe; Dai, Ning; Yu, Qing; Lu, Peijun

2009-08-01

The database with standard 3D tooth crowns has laid the groundwork for dental CAD/CAM system. In this paper, we design the standard tooth crowns in 3DS MAX 9.0 and create a database with these models successfully. Firstly, some key lines are collected from standard tooth pictures. Then we use 3DS MAX 9.0 to design the digital tooth model based on these lines. During the design process, it is important to refer to the standard plaster tooth model. After some tests, the standard tooth models designed with this method are accurate and adaptable; furthermore, it is very easy to perform some operations on the models such as deforming and translating. This method provides a new idea to build the database with standard 3D tooth crowns and a basis for dental CAD/CAM system.

[Inserts for foot deformities].

PubMed

Stinus, H; Weber, F

2005-08-01

Inserts are orthopedic aids in the treatment of foot disorders that result from changes of the static or dynamic situation. Provision of appropriate orthopedic devices can relieve the pain caused by forefoot deformities either in lieu of surgical intervention or in rare cases also following surgical treatment to improve the symptoms of residual pain.Available materials provide support, padding, and cushioning. Inserts are custom-made to measure and/or based on a plaster impression. Determining the indication, prescribing the inlay, and checking the orthosis are the tasks of the physician. One treatment option for relieving the pain of forefoot deformities consists in conservative therapy with an insert combining features of padding and support as well as adjusting a ready-made shoe. The shoe and inlay should constitute a functional unit since often the optimal effect is only achieved with a combination of insert and orthopedic adjustment of the ready-made shoe.

The relationship between oral tori and bite force.

PubMed

Jeong, Chan-Woo; Kim, Kyung-Ho; Jang, Hyo-Won; Kim, Hye-Sun; Huh, Jong-Ki

2018-01-12

Objective The relationship between bite force and torus palatinus or mandibularis remains to be explained. The major aim of this study was to determine the correlation between bite force and oral tori. Methods The bite force of 345 patients was measured with a bite force recorder; impressions of the shape and size of the oral tori were taken on plaster models prior to orthodontic treatments. Subsequently, the relationship between oral tori and bite force was analyzed. Results The size, shape, and incidence of torus palatinus was not significantly correlated with bite force. However, the size of torus mandibularis increased significantly in proportion to the bite force (p = 0.020). The occurrence of different types of oral tori was not correlated with the bite force. Discussion The size of torus mandibularis provides information about bite force and can thus be used to clinically assess occlusal stress.

Cretaceous Footprints Found on Goddard Campus

NASA Image and Video Library

2017-12-08

Seen here we have started to encase the dinosaur footprints in what is known as a field jacket. A field jacket is much like a cast that a doctor would place on a broken arm or leg. Our field jacket consisted of many layers of burlap soaked in plaster-of-Paris into which we also laminate metal pipes to act like splints for additional support. Here Michael is working to remove the very hard sandstone layer below the iron-rich clay layer in which the prints were preserved. Photo taken on January 7, 2013. Credit: NASA/GSFC/Rebecca Roth NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Karl Ludloff (1864-1945): An Inventive Orthopedic Surgeon, His Work and His Surgical Technique for the Correction of Hallux Valgus.

PubMed

Markatos, Konstantinos; Karaoglanis, Georgios; Damaskos, Christos; Garmpis, Nikolaos; Tsourouflis, Gerasimos; Laios, Konstantinos; Tsoucalas, Gregory

2018-05-01

The purpose of this article is to summarize the work and pioneering achievements in the field of orthopedic surgery of the German orthopedic surgeon Karl Ludloff. Ludloff had an impact in the diagnostics, physical examination, orthopedic imaging, and orthopedic surgical technique of his era. He was a pioneer in the surgical treatment of dysplastic hip, anterior cruciate ligament reconstruction, and hallux valgus. His surgical technique for the correction of hallux valgus, initially stabilized with plaster of Paris, remained unpopular among other orthopedic surgeons for decades. In the 1990s, the advent and use of improved orthopedic materials for fixation attracted the interest of numerous orthopedic surgeons in the Ludloff osteotomy for its ability to correct the deformity in all 3 dimensions, its anatomic outcomes, and its low recurrence rate and patient satisfaction.

Metals - from privation to pollution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ulmer, D.D.

1973-07-01

It is becoming more apparent that the environment is not an unlimited void which can safely contain forever all of the by-products of man's activities. In some ways metal pollution raises different considerations from other forms of pollution. Metals are not man made, rather, they occur in nature but their distribution has been altered by man. In order to accurately assess the risks of pollution, meaningful data are required; however, limitations of analytical chemistry presently hinder accurate estimates of some metals. It is difficult to distinguish many metals from the effects of their excess because they have normal functions inmore » living systems. The hazards of lead and mercury are examined. Lead is primarily due to the ingestion of paint and plaster in slum housing. Mercury is a hazard because of industrial discharges in inland waterways and in the form of fungicides.« less

Pose estimation of teeth through crown-shape matching

NASA Astrophysics Data System (ADS)

Mok, Vevin; Ong, Sim Heng; Foong, Kelvin W. C.; Kondo, Toshiaki

2002-05-01

This paper presents a technique for determining a tooth's pose given a dental plaster cast and a set of generic tooth models. The ultimate goal of pose estimation is to obtain information about the sizes and positions of the roots, which lie hidden within the gums, without the use of X-rays, CT or MRI. In our approach, the tooth of interest is first extracted from the 3D dental cast image through segmentation. 2D views are then generated from the extracted tooth and are matched against a target view generated from the generic model with known pose. Additional views are generated in the vicinity of the best view and the entire process is repeated until convergence. Upon convergence, the generic tooth is superimposed onto the dental cast to show the position of the root. The results of applying the technique to canines demonstrate the excellent potential of the algorithm for generic tooth fitting.

A boy with oral hair: case report.

PubMed

Agha-Hosseini, Farzaneh; Etesam, Farideh; Rohani, Bita

2007-09-01

In personal communication we have never seen or heard of hair being detected in the oral cavity. Even Julia Pastrana, the famous "Bearded Lady" of the 1800's, had no record of oral hair, although her entire body was covered with hair. Extensive records of her oral condition, including plaster models of her teeth have been preserved in the Odontological Museum of the Royal College of Surgeons in London city. She suffered from excessive gingival hyperplasia, but apparently no hair existed within the mouth. Some rodents have oral hair as a normal occurrence, but the condition is apparently limited in the animal kingdom. A case of hair occurring naturally in the mouth has been reported only twice previously. A third case of this rare anomaly is reported here. In this case, multiple hairs were found at the gingival sulcus in the labial, buccal, lingual and palatal tooth surfaces in an 11-year-old boy.

Leveraging metal matrix composites to reduce costs in space mechanisms

NASA Technical Reports Server (NTRS)

Nye, Ted; Claridge, Rex; Walker, Jim

1994-01-01

Advanced metal matrix composites may be one of the most promising technologies for reducing cost in structural components without compromise to strength or stiffness. A microlight 12.50 N (2.81 lb), two-axis, solar array drive assembly (SADA) was made for the Advanced Materials Applications to Space Structures (AMASS) Program flight experiment. The SADA had both its inner and outer axis housings fabricated from silicon carbide particulate reinforced alumimun. Two versions of the housings were made. The first was machined from a solid billet of material. The second was plaster cast to a near net shape that required minimal finish machining. Both manufacturing methods were compared upon completion. Results showed a cost savings with the cast housing was possible for quantities greater than one and probable for quantities greater than two. For quantities approaching ten, casting resulted in a reduction factor of almost three in the cost per part.

Thermoluminescence dating of archaeological artefacts from the Middle Neolithic, Bronze Age and the Roman Empire period.

PubMed

Berger, T; Hajek, M; Primerano, W; Vana, N

2002-01-01

Thermoluminescence (TL) dating was applied for artefacts found near the small village of Michelstetten, Lower Austria. Settlements in this region can be traced hack a long time and, according to archaeologists, the discovered artefacts may be as old as 6000 years. A modified sample preparation technique based on the fine-grain method was developed. This technique results in a higher reproducibility and reduces the overall preparation time. For some artefacts the new information of the TL dating leads to an unforeseen re-interpretation of the archaeological age. Furthermore, an iron furnace from the period of the Roman Empire could be dated. For the first time, it was possible to estimate correctly the point of time of the burn-down of an ancient wooden house via an analysis of the house's clay plaster. The fire took place in the sixth century; this was confirmed by dating ceramic artefacts.

Thermal Bridge Effect of Aerated Concrete Block Wall in Cold Regions

NASA Astrophysics Data System (ADS)

Li, Baochang; Guo, Lirong; Li, Yubao; Zhang, Tiantian; Tan, Yufei

2018-01-01

As a self-insulating building material which can meet the 65 percent energy-efficiency requirements in cold region of China, aerated concrete blocks often go moldy, frost heaving, or cause plaster layer hollowing at thermal bridge parts in the extremely cold regions due to the restrictions of environmental climate and construction technique. L-shaped part and T-shaped part of aerated concrete walls are the most easily influenced parts by thermal bridge effect. In this paper, a field test is performed to investigate the scope of the thermal bridge effect. Moreover, a heat transfer calculation model for L-shaped wall and T-shaped wall is developed. According to the simulation results, the temperature fields of the thermal bridge affected regions are simulated and analyzed. The research outputs can provide theoretical basis for the application of aerated concrete wall in extremely cold regions.

Partial Insulation of Aerated Concrete Wall in its Thermal Bridge Regions

NASA Astrophysics Data System (ADS)

Li, Baochang; Guo, Lirong; Li, Yubao; Zhang, Tiantian; Tan, Yufei

2018-01-01

As a self-insulating building material which can meet the 65 percent energy-efficiency requirements in cold region of China, aerated concrete blocks often go moldy, frost heaving, or cause plaster layer hollowing at thermal bridge parts in the extremely cold regions due to the restrictions of environmental climate and construction technique. In this paper, partial insulation measures of the thermal-bridge position of these parts of aerated concrete walls are designed to weaken or even eliminate thermal bridge effect and improve the temperature of thermal-bridge position. A heat transfer calculation model for L-shaped wall and T-shaped wall is developed. Based on the simulation result, the influence of the thickness on the temperature field is analyzed. Consequently, the condensation inside self-thermal-insulating wall and frost heaving caused by condensation and low temperature will be reduced, avoiding damage to the wall body from condensation..

The effect of ultrasonic post instrumentation on root surface temperature.

PubMed

Huttula, Andrew S; Tordik, Patricia A; Imamura, Glen; Eichmiller, Frederick C; McClanahan, Scott B

2006-11-01

This study measured root surface temperature changes when ultrasonic vibration, with and without irrigation, was applied to cemented endodontic posts. Twenty-six, extracted, single-rooted premolars were randomly divided into two groups. Root lengths were standardized, canals instrumented, obturated, and posts cemented into prepared spaces. Thermocouples were positioned at two locations on the proximal root surfaces. Samples were embedded in plaster and brought to 37 degrees C in a water bath. Posts were ultrasonically vibrated for 4 minutes while continuously measuring temperature. Two-way ANOVA compared effects of water coolant and thermocouple location on temperature change. Root surface temperatures were significantly higher (p < 0.001) when posts were instrumented dry. A trend for higher temperatures was observed at coronal thermocouples of nonirrigated teeth and at apical thermocouples of irrigated teeth (p = 0.057). Irrigation during post removal with ultrasonics had a significant impact on the temperature measured at the external root surface.

Quantitation of calcium metabolism in postmenopausal osteoporosis and in scoliosis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bronner, F.; Richelle, L. J.; Saville, P. D.

1963-06-01

By a combination of balance and isotope techniques, the following parameters of Ca metabolism were measured: pool size, rate of loss from pool, urinary excretion, fecal excretion, intake, endogenous fecal Ca, absorption, balance, bone formation, and bone resorption. The subjects were two normal women and five women with postmenopausal osteoporosis, aged 41 to 74 years, and four patients with scoliosis, aged 12 to 22 years. The latter were studied before, shortly after, and many months after immobilization in plaster casts. On the basis of observed relationships, it appeared that the negative Ca balance observed in the older women was duemore » to the low intensity of the various vectors of Ca metabolism, without clearcut distinction between the subjects with and without osteoporosis. Conversely, in the young patients with scoliosis, the negative balance incident to treatment by immobilization was associated with vectors of relatively high intensity whose relationships were altered temporarily.« less

Chromatic dispersive confocal technology for intra-oral scanning: first in-vitro results

NASA Astrophysics Data System (ADS)

Ertl, T.; Zint, M.; Konz, A.; Brauer, E.; Hörhold, H.; Hibst, R.

2015-02-01

Various test objects, plaster models, partially equipped with extracted teeth and pig jaws representing various clinical situations of tooth preparations were used for in-vitro scanning tests with an experimental intra-oral scanning system based on chromatic-dispersive confocal technology. Scanning results were compared against data sets of the same object captured by an industrial μCT measuring system. Compared to μCT data an average error of 18 - 30 μm was achieved for a single tooth scan area and less than 40 to 60 μm error measured over the restoration + the neighbor teeth and pontic areas up to 7 units. Mean error for a full jaw is within 100 - 140 μm. The length error for a 3 - 4 unit bridge situation form contact point to contact point is below 100 μm and excellent interproximal surface coverage and prep margin clarity was achieved.

Thermal diffusivity and adiabatic limit temperature characterization of consolidate granular expanded perlite using the flash method

NASA Astrophysics Data System (ADS)

Raefat, Saad; Garoum, Mohammed; Laaroussi, Najma; Thiam, Macodou; Amarray, Khaoula

2017-07-01

In this work experimental investigation of apparent thermal diffusivity and adiabatic limit temperature of expanded granular perlite mixes has been made using the flash technic. Perlite granulates were sieved to produce essentially three characteristic grain sizes. The consolidated samples were manufactured by mixing controlled proportions of the plaster and water. The effect of the particle size on the diffusivity was examined. The inverse estimation of the diffusivity and the adiabatic limit temperature at the rear face as well as the heat losses coefficients were performed using several numerical global minimization procedures. The function to be minimized is the quadratic distance between the experimental temperature rise at the rear face and the analytical model derived from the one dimension heat conduction. It is shown that, for all granulometry tested, the estimated parameters lead to a good agreement between the mathematical model and experimental data.

Process for Making Ceramic Mold

NASA Technical Reports Server (NTRS)

Buck, Gregory M. (Inventor); Vasquez, Peter (Inventor)

2001-01-01

An improved process for slip casting molds that can be more economically automated and that also exhibits greater dimensional stability is disclosed. The process involves subjecting an investment pattern, preferably made from wax, to successive cycles of wet-dipping in a slurry of colloidal, silica-based binder and dry powder-coating, or stuccoing with plaster of Paris or calcium sulfate mixtures to produce a multi-layer shell over the pattern. The invention as claimed entails applying a primary and a secondary coating to the investment pattern. At least two wet-dipping on in a primary slurry and dry-stuccoing cycles provide the primary coating, and an additional two wet-dippings and dry-stuccoing cycles provide the secondary, or back-up, coating. The primary and secondary coatings produce a multi-layered shell pattern. The multi-layered shell pattern is placed in a furnace first to cure and harden, and then to vaporize the investment pattern, leaving a detailed, high precision shell mold.

Ipsilateral free semitendinosus tendon graft with interference screw fixation for minimally invasive reconstruction of chronic tears of the Achilles tendon.

PubMed

Maffulli, N; Del Buono, A; Loppini, M; Denaro, V

2014-10-01

Minimally invasive ipsilateral semitendinosus reconstruction of large chronic tears aims to be advantageous for the patient in terms of plantar flexion recovery, anthropometric measures, fast return to daily and sport activity, is safe, with low donor site co-morbidities, low risks of wound complications and neurovascular injuries. Tendon gaps greater than 6 cm and in cases of revision surgery (rerupture). Diabetes, vascular diseases, previous anterior cruciate ligament (ACL) reconstruction using ipsilateral semitendinosus tendon graft. The semitendinosus tendon is harvested through an incision in the medial aspect of the popliteal fossa, and the proximal stump is exposed and mobilized through an incision performed 2 cm proximal and medial to the palpable tendon gap. We repeat the same steps distally, approaching the distal stump of the tendon through a 2.5 cm longitudinal incision made 2 cm distal and just anterior to the lateral margin of the distal stump. Through the distal incision, we expose the Kager's space and the postero-superior corner of the osteotomized calcaneum. We drill a bone tunnel into the calcaneum from dorsal to plantar using a cannulated headed reamer. The semitendinosus tendon graft is passed into the proximal stump through a medial-to-lateral small incision, its two ends are moved distally, and finally it is pulled down and shuttled through the bone tunnel. The construct is fixed to the calcaneum using an interference screw. Immobilization in a below the knee plaster cast with the foot in plantar flexion for 2 weeks, weight bearing on the metatarsal heads as tolerated, use elbow crutches, and keep the knee flexed. At 2 weeks, plaster removed, and rehabilitative exercises started, walker cast allowed. Between 2008 and 2010, the procedure was performed on 28 consecutive patients (21 men and 7 women, median age 46 years). At the 2-year follow-up, average ATRS scores significantly improved (p < 0.0001) compared to average preoperative scores with good to excellent outcomes for 26 out of 28 patients (93 %); the maximum calf circumference also improved considerably whereby no clinical or functional relevance compared to the contralateral side observed. Of the 28 patients 16 (57 %) could practice sport at the same preinjury level, whereby 1 patient experienced persistent pain over the distal wound, which ameliorated after desensitization therapy.

[Exploring a new method for superimposition of pre-treatment and post-treatment mandibular digital dental casts in adults].

PubMed

Dai, F F; Liu, Y; Xu, T M; Chen, G

2018-04-18

To explore a cone beam computed tomography (CBCT)-independent method for mandibular digital dental cast superimposition to evaluate three-dimensional (3D) mandibular tooth movement after orthodontic treatment in adults, and to evaluate the accuracy of this method. Fifteen post-extraction orthodontic treatment adults from the Department of Orthodontics, Peking University School and Hospital of Stomatology were included. All the patients had four first premolars extracted, and were treated with straight wire appliance. The pre- and post-treatment plaster dental casts and craniofacial CBCT scans were obtained. The plaster dental casts were transferred to digital dental casts by 3D laser scanning, and lateral cephalograms were created from the craniofacial CBCT scans by orthogonal projection. The lateral cephalogram-based mandibular digital dental cast superimposition was achieved by sequential maxillary dental cast superimposition registered on the palatal stable region, occlusal transfer, and adjustment of mandibular rotation and translation obtained from lateral cephalogram superimposition. The accuracy of the lateral cephalogram-based mandibular digital dental cast superimposition method was evaluated with the CBCT-based mandibular digital dental cast superimposition method as the standard reference. After mandibular digital dental cast superimposition using both methods, 3D coordinate system was established, and 3D displacements of the lower bilateral first molars, canines and central incisors were measured. Differences between the two superimposition methods in tooth displacement measurements were assessed using the paired t-test with the level of statistical significance set at P<0.05. No significant differences were found between the lateral cephalogram-based and CBCT-based mandibular digital dental cast superimposition methods in 3D displacements of the lower first molars, and sagittal and vertical displacements of the canines and central incisors; transverse displacements of the canines and central incisors differed by (0.3±0.5) mm with statistical significance. The lateral cephalogram-based mandibular digital dental cast superimposition method has the similar accuracy as the CBCT-based mandibular digital dental cast superimposition method in 3D evaluation of mandibular orthodontic tooth displacement, except for minor differences for the transverse displacements of anterior teeth. This method is applicable to adult patients with conventional orthodontic treatment records, especially the previous precious orthodontic data in the absence of CBCT scans.

Anthropogenic salts from deteriorated stones of a historical monument (Kraków, Poland)

NASA Astrophysics Data System (ADS)

Marszałek, Mariola; Prajer, Marta

2017-04-01

The results focus on the stone architectonic elements of the Hebdowski Palace in the Okół, an old, medieval part of Kraków. The object was built around 1400, then rebuilt at the turn of the 17th century and at the first half of the 19th century. Its façade was covered with plaster, whose scaling fragments prior to the renovation in 2015 revealed underneath bricks, particularly in the lower part of the palace. The sandstone elements were used in the main portal, while the limestone ones in window frames of the lower section of the façade, base mouldings, and the buttresses at the corner of Poselska and Senacka streets (one of the oldest streets in Kraków). The stone blocks show various forms of damage, ranging from the accumulation of black crusts and efflorescences to crumbling and scaling of their surfaces. Optical microscopy, scanning electron microscopy (SEM-EDS), micro-Raman spectroscopy and X-ray diffractometry (XRD) were used for analysing deterioration products of the stone samples that were collected during the restoration campaign of 2015. The salt minerals detected in the efflorescences and the black crusts include mainly gypsum CaSO4•2H2O and halite NaCl. On the surface of the limestone gypsum is accompanied by oxalates (whewellite CaC2O4•H2O and/or weddellite CaC2O4•2H2O). The black crust developed on both stone types also contain numerous dust particles and a carbonaceous matter, probably soot. The origin of the anthropogenic salts can be mainly assigned to air pollution, to the stones themselves (mainly in the case of the limestone), and to migration of ions from some elements of the façade (e.g. plaster) in the case of the sandstone. The chemicals used for removing ice from streets and pavements (chiefly NaCl and CaCl2) also seem to be important in the formations of the salts. Finally, the existence of simple life forms, such as lichens and fungi, could result in the precipitation of oxalates. This work has been financially supported by AGH University of Science and Technology (statutory grant No. 11.11.140.319).

Functional outcome following tibio-talar-calcaneal nailing for unstable osteoporotic ankle fractures.

PubMed

Jonas, S C; Young, A F; Curwen, C H; McCann, P A

2013-07-01

Fragility fractures of the ankle are increasing in incidence. Such fractures typically occur from low-energy injuries but lead to disproportionately high levels of morbidity. Ankle fractures in this age group are managed conservatively in plaster or by open reduction and internal fixation. Both modalities have shown high rates of failure in terms of delayed union or mal-union together with perioperative complications such as implant failure and wound breakdown. The optimal treatment of these patients remains controversial. We aimed to review the functional outcome of patients with ankle fragility fractures primarily managed using a tibio-talar-calcaneal nail (TTC). We retrospectively reviewed 31 consecutive patients primarily managed with a TCC nail for osteoporotic fragility fractures about the ankle. Data were collected via case notes, radiographic reviews and by clinical reviews at the outpatient clinic or a telephone follow-up. Information regarding patient characteristics, indication for operation, Arbeitsgemeinschaft für Osteosynthesefragen (AO) fracture classification, operative and postoperative complications, time to radiographic union and current clinical state including Olerud and Molander scores were recorded (as a measure of ankle function). Nine of 31 patients had died by the time of follow-up. Mean preoperative and postoperative Olerud and Molander scores were 56 and 45, respectively. There were no postoperative wound complications. Twenty-nine of 31 patients returned to the same level of mobility as pre-injury. There were three peri-prosthetic fractures managed successfully with nail removal and replacement or plaster cast. There were two nail failures, both in patients who mobilised using only a stick, which were managed by nail removal. Ten of 31 patients were not followed up radiographically due to either infirmity or death. Thirteen of 21 followed up radiographically had evidence of union and 8/21 had none. None, however, had clinical evidence of fracture nonunion. The TTC nail can successfully be used to manage fragility fractures about the ankle in the elderly. Much like fractured neck of femur patients, who also have a high rate of mortality, this allows immediate mobilisation with minimal risk of wound complications. However, careful assessment must be made of each patient's mobility, as there is a significant incidence of device failure in the more active patient. Copyright © 2012 Elsevier Ltd. All rights reserved.

A METHOD TO IMPROVE DOSE ASSESSMENT BY RECONSTRUCTION OF THE COMPLETE ISOTOPES INVENTORY.

PubMed

Bonin, Alice; Tsilanizara, Aimé

2017-06-01

Radiation shielding assessments may underestimate the expected dose if some isotopes at trace level are not considered in the isotopes inventory of the shielded radioactive materials. Indeed, information about traces is not often available. Nevertheless, the activation of some minor isotopic traces may significantly contribute to the dose build-up. This paper presents a new method (Isotopes Inventory Reconstruction-IIR) estimating the concentration of the minor isotopes in the irradiated material at the beginning of the cooling period. The method requires the solution of the inverse problem describing the irradiated material's decay. In a mixture of an irradiated uranium-plutonium oxide shielded by a set-up made of stainless-steel, porous polyethylene plaster and lead methyl methacrylate, the comparison between different methods proves that the IIR-method allows better assessment of the dose than other approximate methods. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Antibacterial Properties of Copper Nanoparticle Dispersions: Influence of Synthesis Conditions and Physicochemical Characteristics

NASA Astrophysics Data System (ADS)

Godymchuk, A.; Frolov, G.; Gusev, A.; Zakharova, O.; Yunda, E.; Kuznetsov, D.; Kolesnikov, E.

2015-11-01

The production of bactericidal plasters, bandages and medicines with the inclusion of copper nanoparticles and copper ions may have a great potential in terms of their biomedical application. The work considers the influence of the synthesis conditions, size, aggregation status, and charge of nanoparticles in aqueous solutions as well as the type of microorganisms to the antibacterial properties of water suspensions of electroexplosive copper nanoparticles in the conditions in vitro in relation to strains Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus, and Bacillus cereus. Water dispersions of copper nanoparticles were shown to inhibit the growth of test cells for both G+ and G- microbacteria but the degree of such an influence strongly depended on the type of a test strain. The authors have demonstrated that use of deeply purified water and alcohol-containing stabilizers at the synthesis of nanoparticles via metals electric erosion in the liquid prevents the copper nanoparticles coagulation and significantly influences on their physicochemical characteristics and, consequently, antibacterial properties.

[Application and prospect of digital technology in the field of orthodontics].

PubMed

Zhou, Y H

2016-06-01

The three-dimensional(3D)digital technology has brought a revolutionary change in diagnostic planning and treatment strategy of orthodontics. Acquisition of 3D image data of the hard and soft tissues of the patients, diagnostic analysis and treatment prediction, and ultimately the individualized orthodontic appliance, will become the development trend and workflow of the 3D orthodontics. With the development of 3D digital technology, the traditional plaster model has been gradually replacing by 3D digital models. Meanwhile, 3D facial soft tissue scan and cone-beam CT scan have been gradually applied to clinical orthodontics, making it possible to get 3D virtual anatomical structure for patients. With the help of digital technology, the diagnostic process is much easier for orthodontist. However how to command the whole digital workflow and put it into practice in the daily work is still a long way to go. The purpose of this article is to enlighten the orthodontists interested in digital technology and discuss the future of digital orthodontics in China.

A Method for Optimizing Lightweight-Gypsum Design Based on Sequential Measurements of Physical Parameters

NASA Astrophysics Data System (ADS)

Vimmrová, Alena; Kočí, Václav; Krejsová, Jitka; Černý, Robert

2016-06-01

A method for lightweight-gypsum material design using waste stone dust as the foaming agent is described. The main objective is to reach several physical properties which are inversely related in a certain way. Therefore, a linear optimization method is applied to handle this task systematically. The optimization process is based on sequential measurement of physical properties. The results are subsequently point-awarded according to a complex point criterion and new composition is proposed. After 17 trials the final mixture is obtained, having the bulk density equal to (586 ± 19) kg/m3 and compressive strength (1.10 ± 0.07) MPa. According to a detailed comparative analysis with reference gypsum, the newly developed material can be used as excellent thermally insulating interior plaster with the thermal conductivity of (0.082 ± 0.005) W/(m·K). In addition, its practical application can bring substantial economic and environmental benefits as the material contains 25 % of waste stone dust.

Histopathological Changes in the Periphery of the Sciatic Nerve of Rats after Knee Joint Immobilization

PubMed Central

Yoshida, Shinya; Matsuzaki, Taro; Kamijo, Akio; Araki, Yoshitaka; Sakamoto, Makoto; Moriyama, Shigenori; Hoso, Masahiro

2013-01-01

[Purpose] This study was performed to investigate the histological changes that occur in the periphery of the sciatic nerve in rats undergoing knee immobilization. [Subjects and Methods] 29 male 9-week-old Wistar rats were divided randomly into a control group (C group, n = 7) and an immobilized group (I group, n = 22). The animals in the I group had the left knee joint immobilized in maximal flexion with plaster casts for two weeks. After the experimental period, we obtained cross-sections of tissues from the center of the left thigh, and the periphery of the sciatic nerve was observed under an optical microscope after hematoxylin-eosin staining. [Results] In contrast to the rats of C group, the rats in I group showed adherence between the bundle of nerve fibers and perineurium, as well as thickening of the perineurium. These histological changes were statistically significant. [Conclusions] Immobilization of the knee joints of rats resulted in characteristic histological changes in the connective tissue around the sciatic nerve. PMID:24259816

Acute flexor tendon injury following midshaft radius and ulna fractures in a paediatric patient.

PubMed

Williams, James; Wharton, Rupert; Peev, Peter; Horwitz, Maxim

2018-06-01

Delayed rupture of the extensor and flexor tendons are recognised complications of distal radius fractures. However, acute flexor tendon rupture in the context of forearm fractures is rare. A twelve-year-old female sustained midshaft fractures of the radius and ulna. Intra-operatively the flexor pollicis longus (FPL) was found to be stripped from its musculotendinous junction at the level of the fracture fragment. The ruptured tendon was repaired using a modified Krackow technique at the time of fracture fixation. The repair was protected in plaster of Paris prior to referral to the paediatric hand clinic. The patient made a full recovery. Flexor tendon injury is a rare but potentially devastating consequence of acute forearm fractures. High energy trauma, significant volar angulation of the fracture fragment and clinical signs of flexor tendon injury should raise suspicion of this injury. A high index of suspicion in conjunction with repeat clinical examination of flexor tendon function should be performed before opting for closed management or intramedullary nailing in paediatric patients.

A method based on infrared detection for determining the moisture content of ceramic plaster materials.

PubMed

Macias-Melo, E V; Aguilar-Castro, K M; Alvarez-Lemus, M A; Flores-Prieto, J J

2015-09-01

In this work, we describe a methodology for developing a mathematical model based on infrared (IR) detection to determine the moisture content (M) in solid samples. For this purpose, an experimental setup was designed, developed and calibrated against the gravimetric method. The experimental arrangement allowed for the simultaneous measurement of M and the electromotive force (EMF), fitting the experimental variables as much as possible. These variables were correlated by a mathematical model, and the obtained correlation was M=1.12×exp(3.47×EMF), ±2.54%. This finding suggests that it is feasible to measure the moisture content when it has greater values than 2.54%. The proposed methodology could be used for different conditions of temperature, relative humidity and drying rates to evaluate the influence of these variables on the amount of energy received by the IR detector. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Electromagnetic navigated positioning of the maxilla after Le Fort I osteotomy in preclinical orthognathic surgery cases.

PubMed

Berger, Moritz; Nova, Igor; Kallus, Sebastian; Ristow, Oliver; Eisenmann, Urs; Freudlsperger, Christian; Seeberger, Robin; Hoffmann, Jürgen; Dickhaus, Hartmut

2017-03-01

Inaccuracies in orthognathic surgery can be caused during face-bow registration, model surgery on plaster models, and intermaxillary splint manufacturing. Electromagnetic (EM) navigation is a promising method for splintless digitized maxillary positioning. After performing Le Fort I osteotomy on 10 plastic skulls, the target position of the maxilla was guided by an EM navigation system. Specially implemented software illustrated the target position by real-time multistage colored three-dimensional imaging. Accuracy was determined by using pre- and postoperative cone beam computed tomography. The high accuracy of the EM system was underlined by the fact that it had a navigated maxilla position discrepancy of only 0.4 mm, which was verified by postoperative cone beam computed tomography. This preclinical study demonstrates a precise digitized approach for splintless maxillary repositioning after Le Fort I osteotomy. The accuracy and intuitive illustration of the introduced EM navigation system is promising for potential daily use in orthognathic surgery. Copyright © 2016 Elsevier Inc. All rights reserved.

The evolution of peer review as a basis for scientific publication: directional selection towards a robust discipline?

PubMed

Ferreira, Catarina; Bastille-Rousseau, Guillaume; Bennett, Amanda M; Ellington, E Hance; Terwissen, Christine; Austin, Cayla; Borlestean, Adrian; Boudreau, Melanie R; Chan, Kevin; Forsythe, Adrian; Hossie, Thomas J; Landolt, Kristen; Longhi, Jessica; Otis, Josée-Anne; Peers, Michael J L; Rae, Jason; Seguin, Jacob; Watt, Cristen; Wehtje, Morgan; Murray, Dennis L

2016-08-01

Peer review is pivotal to science and academia, as it represents a widely accepted strategy for ensuring quality control in scientific research. Yet, the peer-review system is poorly adapted to recent changes in the discipline and current societal needs. We provide historical context for the cultural lag that governs peer review that has eventually led to the system's current structural weaknesses (voluntary review, unstandardized review criteria, decentralized process). We argue that some current attempts to upgrade or otherwise modify the peer-review system are merely sticking-plaster solutions to these fundamental flaws, and therefore are unlikely to resolve them in the long term. We claim that for peer review to be relevant, effective, and contemporary with today's publishing demands across scientific disciplines, its main components need to be redesigned. We propose directional changes that are likely to improve the quality, rigour, and timeliness of peer review, and thereby ensure that this critical process serves the community it was created for. © 2015 Cambridge Philosophical Society.

Measurement of heart sounds with EMFi transducer.

PubMed

Kärki, Satu; Kääriäinen, Minna; Lekkala, Jukka

2007-01-01

A measurement system for heart sounds was implemented by using ElectroMechanical Film (EMFi). Heart sounds are produced by the vibrations of the cardiac structure. An EMFi transducer attached to the skin of the chest wall converts these mechanical vibrations into an electrical signal. Furthermore, the signal is amplified and transmitted to the computer. The data is analyzed with Matlab software. The low-frequency components of the measured signal (respiration and pulsation of the heart) are filtered out as well as the 50 Hz noise. Also the power spectral density (PSD) plot is computed. In test measurements, the signal was measured with respiration and by holding breath. From the filtered signal, the first (S1) and the second (S2) heart sound can be clearly seen in both cases. In addition, from the raw data signals the respiration frequency and the heart rate can be determined. In future applications, with the EMFi material it is possible to implement a plaster-like transducer measuring vital signals.

Work-related to musculoskeletal disorder amongst Malaysian construction trade workers: Bricklayers

NASA Astrophysics Data System (ADS)

Lop, Nor Suzila; Kamar, Izatul Farrita Mohd; Aziz, Mohd Nasiruddin Abdul; Abdullah, Lizawati; Akhir, Norizan Mt

2017-10-01

Construction sector is one of the highest risk industries contributing to the development of work-related musculoskeletal disorders. In general construction activities involve the composition of various construction trades, such as painting, plastering, concreting, paving and bricklaying. Different construction trades workers are exposed to risk factors depending their job and task. There are risk factors associated with the construction trade workers activities such as concrete work, brickwork, piling work excavation works and etc. Thus, the aim of this research is to document the critical activities that affect the musculoskeletal disorders amongst Malaysian construction trade workers, in particular to the bricklayers. The objective of this research is to identify the critical activities that affect to the musculoskeletal disorder among the bricklayers. The data for this research was collected via observation to the construction workers for the specific trades which are bricklayers in Perak. Finding of this research is by identifying the critical activities involved that affect the musculoskeletal disorder suffering among bricklayers.

In situ assessment of structural timber elements of a historic building by infrared thermography and ultrasonic velocity

NASA Astrophysics Data System (ADS)

Kandemir-Yucel, A.; Tavukcuoglu, A.; Caner-Saltik, E. N.

2007-01-01

The infrared thermography (IRT) and the ultrasonic velocity measurements (UVM) promise to be particularly important to assess the state of deterioration and the adequacy of the boundary and microclimatic conditions for timber elements. These non-destructive methods supported by laboratory analyses of timber samples were conducted on a 13th century monument, Aslanhane Mosque in Ankara, Turkey. The combined interpretation of the results was done to assess the condition of structural timber elements in terms of their state of preservation, the dampness problems and the recent incompatible repairs affecting them. Results indicated that moist areas in the structure were associated with roof drainage problems and the repairs undertaken with cement-based mortars and plasters and oil-based paints. Juxtaposition of the IRT and UVM together with laboratory analyses was found to be useful to assess the soundness of timber, enhanced the accuracy and effectiveness of the survey and facilitated to build up the urgent and long-term conservation programs.

Inkjet-Printed Graphene/PEDOT:PSS Temperature Sensors on a Skin-Conformable Polyurethane Substrate.

PubMed

Vuorinen, Tiina; Niittynen, Juha; Kankkunen, Timo; Kraft, Thomas M; Mäntysalo, Matti

2016-10-18

Epidermal electronic systems (EESs) are skin-like electronic systems, which can be used to measure several physiological parameters from the skin. This paper presents materials and a simple, straightforward fabrication process for skin-conformable inkjet-printed temperature sensors. Epidermal temperature sensors are already presented in some studies, but they are mainly fabricated using traditional photolithography processes. These traditional fabrication routes have several processing steps and they create a substantial amount of material waste. Hence utilizing printing processes, the EES may become attractive for disposable systems by decreasing the manufacturing costs and reducing the wasted materials. In this study, the sensors are fabricated with inkjet-printed graphene/PEDOT:PSS ink and the printing is done on top of a skin-conformable polyurethane plaster (adhesive bandage). Sensor characterization was conducted both in inert and ambient atmosphere and the graphene/PEDOT:PSS temperature sensors (thermistors) were able reach higher than 0.06% per degree Celsius sensitivity in an optimal environment exhibiting negative temperature dependence.

Determination of the Airborne Sound Insulation of a Straw Bale Partition Wall

NASA Astrophysics Data System (ADS)

Teslík, Jiří; Fabian, Radek; Hrubá, Barbora

2017-06-01

This paper describes the results of a scientific project focused on determining of the Airborne Sound Insulation of a peripheral non-load bearing wall made of straw bales expressed by Weighted Sound Reduction Index. Weighted Sound Reduction Index was determined by measuring in the certified acoustic laboratory at the Faculty of Mechanical Engineering at Brno University of Technology. The measured structure of the straw wall was modified in combinations with various materials, so the results include a wide range of possible compositions of the wall. The key modification was application of plaster on both sides of the straw bale wall. This construction as is frequently done in actual straw houses. The additional measurements were performed on the straw wall with several variants of additional wall of slab materials. The airborne sound insulation value has been also measured in separate stages of the construction. Thus it is possible to compare and determinate the effect of the single layers on the airborne sound insulation.

History of clubfoot treatment, part I: From manipulation in antiquity to splint and plaster in Renaissance before tenotomy.

PubMed

Hernigou, Philippe; Huys, Maxime; Pariat, Jacques; Jammal, Sibylle

2017-08-01

Idiopathic clubfoot is one of the most common problems in paediatric orthopaedics. The treatment is controversial and continues to be one of the challenges in paediatric orthopaedics. The aim of this review is to assess the different methods of clubfoot treatment used over the years in light of the documentation present in the literature and art paintings from the antiquity to the end of the 19th century. The aim of this paper is to review all treatment methods of the clubfoot over the years that were proposed to provide patients a functional, pain-free, normal-looking foot, with good mobility, without calluses, and requiring no special shoes. Hippocrates was the first to write references about treatment methods of clubfoot. After the Middle Ages and the Renaissance where patients were treated by barber-surgeons, quacks and charlatans, bonesetters, and trussmakers, there were more detailed studies on the disease, with the help of famous names in medicine such as Venel and Scarpa.

[Which foot deformities should be radiologist be familiar with?

PubMed

von Stillfried, E

2018-05-01

Most deformities of the foot are visible at birth and can be diagnosed without imaging. They can be divided into congenital flexible, congenital structural and acquired foot deformities. The most common congenital flexible foot deformity in children is the metatarsus adductus, which usually requires no long-term therapy. Regarding congenital structural deformities, such as the clubfoot and talus verticalis, plaster therapy should be started during the first week of life, so that by the end of the first year of life and the beginning of the verticalization, a pain-free resilient foot with normal function is present. Imaging is usually only necessary if a relapse arises. Coalitio of the tarsal bones is often visible only in the course of growth through the development of a rigid flatfoot and always requires imaging to confirm the diagnosis. This article is intended to give the radiologist an overview of the most important deformities and to inform about their course and therapy.

Influence of the chemical structure on odor qualities and odor thresholds of halogenated guaiacol-derived odorants

NASA Astrophysics Data System (ADS)

Juhlke, Florian; Lorber, Katja; Wagenstaller, Maria; Buettner, Andrea

2017-12-01

Chlorinated guaiacol derivatives are found in waste water of pulp mills using chlorine in the bleaching process of wood pulp. They can also be detected in fish tissue, possibly causing off-odors. To date, there is no systematic investigation on the odor properties of halogenated guaiacol derivatives. To close this gap, odor thresholds in air and odor qualities of 14 compounds were determined by gas chromatography-olfactometry. Overall, the investigated compounds elicited smells that are characteristic for guaiacol, namely smoky, sweet, vanilla-like, but also medicinal and plaster-like. Their odor thresholds in air were, however, very low, ranging from 0.00072 to 23 ng/Lair. The lowest thresholds were found for 5-chloro- and 5-bromoguaiacol, followed by 4,5-dichloro- and 6-chloroguaiacol. Moreover, some inter-individual differences in odor threshold values could be observed, with the highest variations having been recorded for the individual values of 5-iodo- and 4-bromoguaiacol.