Spatially resolved sampling reveals dynamic microbial communities in rising hydrothermal plumes across a back-arc basin

PubMed Central

Sheik, Cody S; Anantharaman, Karthik; Breier, John A; Sylvan, Jason B; Edwards, Katrina J; Dick, Gregory J

2015-01-01

Within hydrothermal plumes, chemosynthetic processes and microbe–mineral interactions drive primary productivity in deep-ocean food webs and may influence transport of elements such as iron. However, the source of microorganisms in plumes and the factors governing how these communities assemble are poorly understood, in part due to lack of data from early stages of plume formation. In this study, we examined microbial community composition of rising hydrothermal plumes from five vent fields along the Eastern Lau Spreading Center. Seafloor and plume microbial communities were significantly dissimilar and shared few phylotypes. Plume communities were highly similar to each other with significant differences in community membership only between Kilo Moana and Mariner, two vents that are separated by extremes in depth, latitude and geochemistry. Systematic sampling of waters surrounding the vents revealed that species richness and phylogenetic diversity was typically highest near the vent orifice, implying mixing of microbial communities from the surrounding habitats. Above-plume background communities were primarily dominated by SAR11, SAR324 and MG-I Archaea, while SUP05, Sulfurovum, Sulfurimonas, SAR324 and Alteromonas were abundant in plume and near-bottom background communities. These results show that the ubiquitous water-column microorganisms populate plume communities, and that the composition of background seawater exerts primary influence on plume community composition, with secondary influence from geochemical and/or physical properties of vents. Many of these pervasive deep-ocean organisms are capable of lithotrophy, suggesting that they are poised to use inorganic electron donors encountered in hydrothermal plumes. PMID:25489728

Interaction between Edge-Driven Convection and Mantle Plumes

NASA Astrophysics Data System (ADS)

Manjón-Cabeza Córdoba, A.; Ballmer, M.

2017-12-01

Intraplate volcanism can occur in a variety of geodynamic settings. Its characteristics can inform about the underlying mantle dynamics. A non-negligible number of intraplate oceanic volcanoes are located close to continental shelves (e.g. Bermuda, Canary Islands, Cape Verde…). In these regions, any putative plumes would interact with Edge-Driven Convection (EDC), a mode of Small-Scale Convection that is triggered along steps of lithospheric thickness. We have systematically explored 2-D geodynamic models of EDC, varying e.g. the viscosity of the mantle, geometry of the edge, potential temperature, etc. In addition, we study the influence of a mantle plume with variable excess temperature and buoyancy flux at a given distance to the edge. The mantle-convection code is coupled with a new melting parameterization that considers the depletion effect on productivity. We apply this parameterization not only to predict the extent of melting for a given lithology, but also the major-element composition of extracted melts for comparison with geochemical data. Results show that the first EDC upwellings are always localized in the oceanic domain at a distance from the continental margin that depends on mantle viscosity. The initial geometry of the edge does not have a significant influence on the "steady-state" shape of EDC. Depending on the distance of the plume from the edge and plume vigor, the plume is either deflected or enhanced by EDC. The mix of materials that melts in the mantle, as well as the amount of melting, is controlled by the interaction of the plume with EDC (e.g., with melting restricted to fertile heterogeneities in the end-member EDC case). Because several model parameters affect this interaction and related melting, a joint analysis of major-element and trace-element composition of hotspot lavas is required to constrain mantle processes.

Chemical trends in ocean islands explained by plume–slab interaction

NASA Astrophysics Data System (ADS)

Dannberg, Juliane; Gassmöller, Rene

2018-04-01

Earth's surface shows many features, of which the genesis can be understood only through their connection with processes in Earth's deep interior. Recent studies indicate that spatial geochemical patterns at oceanic islands correspond to structures in the lowermost mantle inferred from seismic tomographic models. This suggests that hot, buoyant upwellings can carry chemical heterogeneities from the deep lower mantle toward the surface, providing a window to the composition of the lowermost mantle. The exact nature of this link between surface and deep Earth remains debated and poorly understood. Using computational models, we show that subducted slabs interacting with dense thermochemical piles can trigger the ascent of hot plumes that inherit chemical gradients present in the lowermost mantle. We identify two key factors controlling this process: (i) If slabs induce strong lower-mantle flow toward the edges of these piles where plumes rise, the pile-facing side of the plume preferentially samples material originating from the pile, and bilaterally asymmetric chemical zoning develops. (ii) The composition of the melt produced reflects this bilateral zoning if the overlying plate moves roughly perpendicular to the chemical gradient in the plume conduit. Our results explain some of the observed geochemical trends of oceanic islands and provide insights into how these trends may originate.

Synthesis of observations of halogen-containing gases, ozone, and gaseous elemental mercury in the tropospheric plume of Redoubt Volcano, Alaska

NASA Astrophysics Data System (ADS)

Kelly, P. J.; Kern, C.; Lopez, T. M.; Werner, C. A.; Roberts, T. J.; Aiuppa, A.; Wang, B.

2011-12-01

Volcanoes are strong natural sources of halogen-containing acid gases and mercury. Most halogens are emitted from volcanoes as relatively non-reactive hydrogen halide gases, but recent field and modeling studies have shown that these species can be rapidly transformed into reactive forms via heterogeneous in-plume reactions. In order to further examine the chemical reactions that occur in volcanic plumes and their atmospheric impacts, we made ground and aircraft-based measurements of the composition of the tropospheric plume emitted from Redoubt Volcano, Alaska, which injected over 1 Tg of SO2, plus other gases and aerosols, into the subarctic free troposphere during 2009 and 2010. To our knowledge, our data include the first detailed study of ozone in a volcanic plume as well as the first measurements of HBr, HI, gaseous elemental mercury (GEM), and BrO in the plume of an Alaskan volcano. The composition of the plume was measured on June 20, 2010 using base-treated filter packs at the crater rim and by an instrumented fixed-wing aircraft on June 21 and August 19, 2010. The aircraft was used to track the chemical evolution of the plume up to ~30 km downwind (2 hours plume travel time) from the volcano. The airborne data from June 21 reveals rapid chemical ozone destruction in the plume as well as the strong influence chemical heterogeneity in background air had on plume composition. Airborne measurements on August 19 revealed several ppbv of ozone depletion near the center of the plume at a location ~5 km (20 minutes plume travel time) downwind and spectroscopic retrievals from traverses made under the plume show that BrO was present at a similar location. Simulations with the PlumeChem model reproduce the main features of the observed ozone deficits and evolution with time. The field measurements and model results suggest that autocatalytic release of reactive bromine and the formation of BrO can explain ozone destruction in the plume. Thus, volcanic eruptions in Alaska are sources of both non-reactive and reactive halogens and mercury. However, the fate of GEM emitted from volcanoes or incorporated into volcanic plumes warrants further study because our results indicate conditions in volcanic plumes would be conducive to the rapid oxidation of GEM.

System Concept for Remote Measurement of Asteroid Molecular Composition

NASA Astrophysics Data System (ADS)

Hughes, G. B.; Lubin, P. M.; Zhang, Q.; Brashears, T.; Cohen, A. N.; Madajian, J.

2016-12-01

We propose a method for probing the molecular composition of cold solar system targets (asteroids, comets, planets, moons) from a distant vantage, such as from a spacecraft orbiting the object. A directed energy beam is focused on the target. With sufficient flux, the spot temperature rises rapidly, and evaporation of surface materials occurs. The melted spot creates a high-temperature blackbody source, and ejected material creates a plume of surface materials in front of the spot. Molecular and atomic absorption of the blackbody radiation occurs within the ejected plume. Bulk composition of the surface material is investigated by using a spectrometer to view the heated spot through the ejected material. Our proposed method differs from technologies such as Laser-Induced Breakdown Spectroscopy (LIBS), which atomizes and ionizes materials in the target; scattered ions emit characteristic radiation, and the LIBS detector performs atomic composition analysis by observing emission spectra. Standoff distance for LIBS is limited by the strength of characteristic emission, and distances greater than 10 m are problematic. Our proposed method detects atomic and molecular absorption spectra in the plume; standoff distance is limited by the size of heated spot, and the plume opacity; distances on the order of tens of kilometers are immediately feasible. Simulations have been developed for laser heating of a rocky target, with concomitant evaporation. Evaporation rates lead to determination of plume density and opacity. Absorption profiles for selected materials are estimated from plume properties. Initial simulations of absorption profiles with laser heating show great promise for molecular composition analysis from tens of kilometers distance. This paper explores the feasibility a hypothetical mission that seeks to perform surface molecular composition analysis of a near-earth asteroid while the craft orbits the asteroid. Such a system has compelling potential benefit for solar system exploration.

Fine scale mapping of the structure and composition of the Elkhorn Slough (California, USA) tidal plume

NASA Astrophysics Data System (ADS)

Fischer, Andrew M.; Ryan, John P.; Rienecker, Erich V.

2017-01-01

Fine scale mapping of the structure and composition of a tidal ebb plume from a highly modified coastal lagoon (Elkhorn Slough, California, USA) was conducted by combining in situ, observational data sets from surface underway mapping, autonomous underwater vehicle (AUV) profiles, drifter tracking and the analysis of plume structure indices. The results reveal a 6-m-deep, jet-like, sediment laden plume extending one km offshore at low tide, which becomes entrained in the prevailing nearshore circulation. The plume that exits the slough is significantly different from the water that enters the slough. The rapidly evolving discharge plume is associated with elevated and highly correlated (r = 0.93) concentrations of dissolved organic matter and nitrate. While dissolved constituents remain in the shallow plume and are transported northward with the prevailing current, sediment may settle quickly through the water column and can be transported southwestward with the littoral currents. This study illustrates the applications of AUVs, when coupled with additional datasets, for generating higher resolution observational snapshots of dynamic and ephemeral tidal plumes. The results provide unique perspective on small-scale dynamics of an estuarine plume and its influence on coastal ecology.

The interaction of plume heads with compositional discontinuities in the Earth's mantle

NASA Technical Reports Server (NTRS)

Manga, Michael; Stone, Howard A.; O'Connell, Richard J.

1993-01-01

The effects of compositional discontinuities of density and viscosity in the Earth's mantle on the ascent of mantle plume heads is studied using a boundary integral numerical technique. Three specific problems are considered: (1) a plume head rising away from a deformable interface, (2) a plume head passing through an interface, and (3) a plume head approaching the surface of the Earth. For the case of a plume attached to a free-surface, the calculated time-dependent plume shapesare compared with experimental results. Two principle modes of plume head deformation are observed: plume head elingation or the formation of a cavity inside the plume head. The inferred structure of mantle plumes, namely, a large plume head with a long tail, is characteristic of plumes attached to their source region, and also of buoyant material moving away from an interface and of buoyant material moving through an interface from a high- to low-viscosity region. As a rising plume head approaches the upper mantle, most of the lower mantle will quickly drain from the gap between the plume head and the upper mantle if the plume head enters the upper mantle. If the plume head moves from a high- to low-viscosity region, the plume head becomes significantly elongated and, for the viscosity contrasts thought to exist in the Earth, could extend from the 670 km discontinuity to the surface. Plume heads that are extended owing to a viscosity decrease in the upper mantle have a cylindrical geometry. The dynamic surface topography induced by plume heads is bell-shaped when the top of the plume head is at depths greater than about 0.1 plume head radii. As the plume head approaches the surface and spreads, the dynamic topography becomes plateau-shaped. The largest stresses are produced in the early stages of plume spreading when the plume head is still nearly spherical, and the surface expression of these stresses is likely to be dominated by radial extension. As the plume spreads, compressional stresses on the surface are produced beyond the edges of the plume; consequently, extensional features will be produced above the plume head and may be surrounded by a ring of compressional features.

Rapid chemical evolution of tropospheric volcanic emissions from Redoubt Volcano, Alaska, based on observations of ozone and halogen-containing gases

NASA Astrophysics Data System (ADS)

Kelly, Peter J.; Kern, Christoph; Roberts, Tjarda J.; Lopez, Taryn; Werner, Cynthia; Aiuppa, Alessandro

2013-06-01

We report results from an observational and modeling study of reactive chemistry in the tropospheric plume emitted by Redoubt Volcano, Alaska. Our measurements include the first observations of Br and I degassing from an Alaskan volcano, the first study of O3 evolution in a volcanic plume, as well as the first detection of BrO in the plume of a passively degassing Alaskan volcano. This study also represents the first detailed spatially-resolved comparison of measured and modeled O3 depletion in a volcanic plume. The composition of the plume was measured on June 20, 2010 using base-treated filter packs (for F, Cl, Br, I, and S) at the crater rim and by an instrumented fixed-wing aircraft on June 21 and August 19, 2010. The aircraft was used to track the chemical evolution of the plume up to ~ 30 km downwind (2 h plume travel time) from the volcano and was equipped to make in situ observations of O3, water vapor, CO2, SO2, and H2S during both flights plus remote spectroscopic observations of SO2 and BrO on the August 19th flight. The airborne data from June 21 reveal rapid chemical O3 destruction in the plume as well as the strong influence chemical heterogeneity in background air had on plume composition. Spectroscopic retrievals from airborne traverses made under the plume on August 19 show that BrO was present ~ 6 km downwind (20 min plume travel time) and in situ measurements revealed several ppbv of O3 loss near the center of the plume at a similar location downwind. Simulations with the PlumeChem model reproduce the timing and magnitude of the observed O3 deficits and suggest that autocatalytic release of reactive bromine and in-plume formation of BrO were primarily responsible for the observed O3 destruction in the plume. The measurements are therefore in general agreement with recent model studies of reactive halogen formation in volcanic plumes, but also show that field studies must pay close attention to variations in the composition of ambient air entrained into volcanic plumes in order to unambiguously attribute observed O3 anomalies to specific chemical or dynamic processes. Our results suggest that volcanic eruptions in Alaska are sources of reactive halogen species to the subarctic troposphere.

The He isotope composition of the earliest picrites erupted by the Ethiopia plume, implications for mantle plume source

NASA Astrophysics Data System (ADS)

Stuart, Finlay; Rogers, Nick; Davies, Marc

2016-04-01

The earliest basalts erupted by mantle plumes are Mg-rich, and typically derived from mantle with higher potential temperature than those derived from the convecting upper mantle at mid-ocean ridges and ocean islands. The chemistry and isotopic composition of picrites from CFB provide constraints on the composition of deep Earth and thus the origin and differentiation history. We report new He-Sr-Nd-Pb isotopic composition of the picrites from the Ethiopian flood basalt province from the Dilb (Chinese Road) section. They are characterized by high Fe and Ti contents for MgO = 10-22 wt. % implying that the parent magma was derived from a high temperature low melt fraction, most probably from the Afar plume head. The picrite 3He/4He does not exceed 21 Ra, and there is a negative correlation with MgO, the highest 3He/4He corresponding to MgO = 15.4 wt. %. Age-corrected 87Sr/86Sr (0.70392-0.70408) and 143Nd/144Nd (0.512912-0.512987) display little variation and are distinct from MORB and OIB. Age-corrected Pb isotopes display a significant range (e.g. 206Pb/204Pb = 18.70-19.04) and plot above the NHRL. These values contrast with estimates of the modern Afar mantle plume which has lower 3He/4He and Sr, Nd and Pb isotope ratios that are more comparable with typical OIB. These results imply either interaction between melts derived from the Afar mantle plume and a lithospheric component, or that the original Afar mantle plume had a rather unique radiogenic isotope composition. Regardless of the details of the origins of this unusual signal, our observations place a minimum 3He/4He value of 21 Ra for the Afar mantle plume, significantly greater than the present day value of 16 Ra, implying a significant reduction over 30 Myr. In addition the Afar source was less degassed than convecting mantle but more degassed than mantle sampled by the proto-Iceland plume (3He/4He ~50 Ra). This suggests that the largest mantle plumes are not sourced in a single deep mantle domain with a common depletion history and that they do not mix with shallower mantle reservoirs to the same extent.

Large Igneous Provinces, Mantle Plumes, and Continental Break-up: An Overview.

NASA Astrophysics Data System (ADS)

Peate, D. W.

2003-04-01

Although mantle plumes are widely implicated in models for the generation of large igneous provinces (LIPs) and the break-up of supercontinents such as Gondwana, the exact role of the mantle plume in these processes, and even the very existence of mantle plumes, is controversial and hotly debated. The large volumes of magma produced within a LIP (> 10^6 km^3) in a relative short time interval (< few Myrs) require elevated mantle temperatures such as is inferred for a plume, but it is not easy to determine whether the melting occurred as a result of the arrival of a plume head in the shallow mantle or in response to lithospheric extension. Numerous questions remain unresolved: e.g. Can all LIPs be explained by plume-like mantle upwellings, or are non-plume models such as edge-driven convection a plausible alternative?; Are plumes wet-spots rather than hot-spots?; Do they originate from the core-mantle boundary?; How important is the influence of the overlying lithosphere (limiting the upwelling and extent of melting, modifying the composition of deeper melts, and possibly acting as a source for melts)? In this presentation, I will summarise key observations from three young LIP's (< 135 Ma), each associated with continental break-up. These case studies will be: (i) North Atlantic LIP - Iceland plume, (ii) Parana-Etendeka LIP - Tristan plume, and (iii) Ethiopia-Yemen LIP - Afar plume. Aspects that will be considered include: the areal extent, volume and eruption rates of magmatism; temporal relationship of flood basalt volcanism to lithospheric extension and continental break-up; compositional similarities and differences between the flood basalts and more recent lavas from the associated plume; spatial and temporal compositional variations as a means of assessing the location and length-scales of heterogeneities in the upwelling mantle, seismic tomographic images of mantle thermal structure today; crustal structure of the rifted margins from wide-angle and reflection seismic data. These geochemical, tectonic, and geophysical observations will then be used to evaluate the role of a plume in the formation of each of the three LIP's.

The Role of Viscosity Contrast on the Plume Structure and Dynamics in High Rayleigh Number Convection

NASA Astrophysics Data System (ADS)

Kr, Sreenivas; Prakash, Vivek N.; Arakeri, Jaywant H.

2010-11-01

We study the plume structure in high Rayleigh number convection in the limit of large Prandtl numbers. This regime is relevant in Mantle convection, where the plume dynamics is not well understood due to complex rheology and chemical composition. We use analogue laboratory experiments to mimic mantle convection. Our focus in this paper is to understand the role of viscosity ratio, U, between the plume fluid and the ambient fluid on the structure and dynamics of the plumes. The PLIF technique has been used to visualize the structures of plumes rising from a planar source of compositional buoyancy at different regimes of U (1/300 to 2500). In the near-wall planform when U is one, a well-known dendritic line plume structure is observed. As U increases (U > 1; mantle hot spots), there is a morphological transition from line plumes to discrete spherical blobs, accompanied by an increase in the plume spacing and thickness. In vertical sections, as U increases (U > 1), the plume head shape changes from a mushroom-like structure to a "spherical-blob." When the U is decreased below one, (U<1; subduction regime), the formation of cellular patterns is favoured with sheet plumes. Both velocity and mixing efficiency are maximum when U is one, and decreases for extreme values of U. We quantify the morphological changes, dynamics and mixing variations of the plumes from experiments at different regimes.

Resolving the potential mantle reservoirs that influence volcanism in the West Antarctic Rift System

NASA Astrophysics Data System (ADS)

Maletic, E. L.; Darrah, T.

2017-12-01

Lithospheric extension and magmatism are key characteristics of active continental rift zones and are often associated with long-lasting alkaline magmatic provinces. In these settings, a relationship between lithospheric extension and mantle plumes is often assumed for the forces leading to rift evolution and the existence of a plume is commonly inferred, but typically only extension is supported by geological evidence. A prime example of long-lasting magmatism associated with an extensive area of continental rifting is the West Antarctic Rift System (WARS), a 2000 km long zone of ongoing extension within the Antarctic plate. The WARS consists of high alkaline silica-undersaturated igneous rocks with enrichments in light rare earth elements (LREEs). The majority of previous geochemical work on WARS volcanism has focused on bulk classification, modal mineralogy, major element composition, trace element chemistry, and radiogenic isotopes (e.g., Sr, Nd, and Pb isotopes), but very few studies have evaluated volatile composition of volcanics from this region. Previous explanations for WARS volcanism have hypothesized a plume beneath Marie Byrd Land, decompression melting of a fossilized plume head, decompression melting of a stratified mantle source, and mixing of recycled oceanic crust with one or more enriched mantle sources from the deep mantle, though researchers are yet to reach a consensus. Unlike trace elements and radiogenic isotopes which can be recycled between the crust and mantle and which are commonly controlled by degrees of partial melting and prior melt differentiation, noble gases are present in low concentrations and chemically inert, allowing them to serve as reliable tracers of volatile sources and subsurface processes. Here, we present preliminary noble gas isotope (e.g., 3He/4He, CO2/3He, CH4/3He, 40Ar/36Ar, 40Ar*/4He) data for a suite of lava samples from across the WARS. By coupling major and trace element chemistry with noble gas elemental and isotopic composition and other volatiles from a suite of volcanic rocks in the WARS, we can better constrain a magmatic source and provide geological evidence that could support or oppose the existence of a mantle plume, HIMU plume, or deconvolve mantle-lithosphere interactions.

Heterogeneity of the Caribbean plateau mantle source: Sr, O and He isotopic compositions of olivine and clinopyroxene from Gorgona Island

NASA Astrophysics Data System (ADS)

Révillon, S.; Chauvel, C.; Arndt, N. T.; Pik, R.; Martineau, F.; Fourcade, S.; Marty, B.

2002-12-01

The composition of the mantle plumes that created large oceanic plateaus such as Ontong Java or the Caribbean is still poorly known. Geochemical and isotopic studies on accreted portions of the Caribbean plateau have shown that the plume source was heterogeneous and contained isotopically depleted and relatively enriched portions. A distinctive feature of samples from the Caribbean plateau is their unusual Sr isotopic compositions, which, at a given Nd isotopic ratio, are far higher than in samples from other oceanic plateaus. Sr, O and He isotopic compositions of whole rocks and magmatic minerals (clinopyroxene or olivine) separated from komatiites, gabbros and peridotites from Gorgona Island in Colombia were determined to investigate the origin of these anomalously radiogenic compositions. Sequentially leached clinopyroxenes have Sr isotopic compositions in the range 87Sr/ 86Sr=0.70271-0.70352, systematically lower than those of leached and unleached whole rocks. Oxygen isotopic ratios of clinopyroxene vary within the range δ 18O=5.18-5.35‰, similar to that recorded in oceanic island basalts. He isotopic ratios are high ( R/ Ra=8-19). The lower 87Sr/ 86Sr ratios of most of the clinopyroxenes shift the field of the Caribbean plateau in Nd-Sr isotope diagrams toward more 'normal' values, i.e. a position closer to the field defined by mid-ocean ridge basalts and oceanic-island basalts. Three clinopyroxenes have slightly higher 87Sr/ 86Sr ratios that cannot be explained by an assimilation model. The high 87Sr/ 86Sr and variations of 143Nd/ 144Nd are interpreted as a source characteristic. Trace-element ratios, however, are controlled mainly by fractionation during partial melting. We combine these isotopic data in a heterogeneous plume source model that accounts for the diversity of isotopic signatures recorded on Gorgona Island and throughout the Caribbean plateau. The heterogeneities are related to old recycled oceanic lithosphere in the plume source; the high 3He/ 4He ratios may indicate that the source material once resided in the lower mantle.

Lead isotopes reveal bilateral asymmetry and vertical continuity in the Hawaiian mantle plume.

PubMed

Abouchami, W; Hofmann, A W; Galer, S J G; Frey, F A; Eisele, J; Feigenson, M

2005-04-14

The two parallel chains of Hawaiian volcanoes ('Loa' and 'Kea') are known to have statistically different but overlapping radiogenic isotope characteristics. This has been explained by a model of a concentrically zoned mantle plume, where the Kea chain preferentially samples a more peripheral portion of the plume. Using high-precision lead isotope data for both centrally and peripherally located volcanoes, we show here that the two trends have very little compositional overlap and instead reveal bilateral, non-concentric plume zones, probably derived from the plume source in the mantle. On a smaller scale, along the Kea chain, there are isotopic differences between the youngest lavas from the Mauna Kea and Kilauea volcanoes, but the 550-thousand-year-old Mauna Kea lavas are isotopically identical to Kilauea lavas, consistent with Mauna Kea's position relative to the plume, which was then similar to that of present-day Kilauea. We therefore conclude that narrow (less than 50 kilometres wide) compositional streaks, as well as the larger-scale bilateral zonation, are vertically continuous over tens to hundreds of kilometres within the plume.

Linking lowermost mantle structure, core-mantle boundary heat flux and mantle plume formation

NASA Astrophysics Data System (ADS)

Li, Mingming; Zhong, Shijie; Olson, Peter

2018-04-01

The dynamics of Earth's lowermost mantle exert significant control on the formation of mantle plumes and the core-mantle boundary (CMB) heat flux. However, it is not clear if and how the variation of CMB heat flux and mantle plume activity are related. Here, we perform geodynamic model experiments that show how temporal variations in CMB heat flux and pulses of mantle plumes are related to morphologic changes of the thermochemical piles of large-scale compositional heterogeneities in Earth's lowermost mantle, represented by the large low shear velocity provinces (LLSVPs). We find good correlation between the morphologic changes of the thermochemical piles and the time variation of CMB heat flux. The morphology of the thermochemical piles is significantly altered during the initiation and ascent of strong mantle plumes, and the changes in pile morphology cause variations in the local and the total CMB heat flux. Our modeling results indicate that plume-induced episodic variations of CMB heat flux link geomagnetic superchrons to pulses of surface volcanism, although the relative timing of these two phenomena remains problematic. We also find that the density distribution in thermochemical piles is heterogeneous, and that the piles are denser on average than the surrounding mantle when both thermal and chemical effects are included.

Rapid chemical evolution of tropospheric volcanic emissions from Redoubt Volcano, Alaska, based on observations of ozone and halogen-containing gases

USGS Publications Warehouse

Werner, Cynthia A.; Kelly, Peter; Kern, Christoph; Roberts, T.J.; Aluppe, A.

2013-01-01

We report results from an observational and modeling study of reactive chemistry in the tropospheric plume emitted by Redoubt Volcano, Alaska. Our measurements include the first observations of Br and I degassing from an Alaskan volcano, the first study of O3 evolution in a volcanic plume, as well as the first detection of BrO in the plume of a passively degassing Alaskan volcano. This study also represents the first detailed spatially-resolved comparison of measured and modeled O3 depletion in a volcanic plume. The composition of the plume was measured on June 20, 2010 using base-treated filter packs (for F, Cl, Br, I, and S) at the crater rim and by an instrumented fixed-wing aircraft on June 21 and August 19, 2010. The aircraft was used to track the chemical evolution of the plume up to ~ 30 km downwind (2 h plume travel time) from the volcano and was equipped to make in situ observations of O3, water vapor, CO2, SO2, and H2S during both flights plus remote spectroscopic observations of SO2 and BrO on the August 19th flight. The airborne data from June 21 reveal rapid chemical O3 destruction in the plume as well as the strong influence chemical heterogeneity in background air had on plume composition. Spectroscopic retrievals from airborne traverses made under the plume on August 19 show that BrO was present ~ 6 km downwind (20 min plume travel time) and in situ measurements revealed several ppbv of O3 loss near the center of the plume at a similar location downwind. Simulations with the PlumeChem model reproduce the timing and magnitude of the observed O3 deficits and suggest that autocatalytic release of reactive bromine and in-plume formation of BrO were primarily responsible for the observed O3 destruction in the plume. The measurements are therefore in general agreement with recent model studies of reactive halogen formation in volcanic plumes, but also show that field studies must pay close attention to variations in the composition of ambient air entrained into volcanic plumes in order to unambiguously attribute observed O3 anomalies to specific chemical or dynamic processes. Our results suggest that volcanic eruptions in Alaska are sources of reactive halogen species to the subarctic troposphere.

Tracking Reactive Nitrogen Sources, Chemistry and Deposition in Urban Environments Using Stable Isotopes

NASA Astrophysics Data System (ADS)

Hastings, M. G.; Clark, S. C.; Chai, J.; Joyce, E.; Miller, D. J.; Schiebel, H.; Walters, W.

2017-12-01

Reactive nitrogen (Nr) includes compounds such as nitrogen oxides (NOx, HONO), ammonia (NH3), nitrate (NO3-), ammonium (NH4+), and organic nitrates. These compounds serve major roles in controlling the composition of our atmosphere, and have a direct impact on ecosystem health and water quality. Our research is focused on using stable isotopes of Nr to investigate variations in sources, chemistry, atmospheric transport, and deposition. Our aim is to fingerprint distinct emission sources - such as vehicles, power plants, aircraft, agriculature, wildfires, and lightning - and track their influence in the environment. We have recently characterized vehicle emission plumes, emissions from agricultural soils under different management practices, and (in the near future) wildfire plumes in the western U.S. Our approach targets characterizing the isotopic composition of NOx, HONO, and NH3 at both the emissions source and the plume scale. In contrast to large ranges found for individual tailpipe emissions of NOx, on-road plumes in the U.S. have a mean δ15N of -4.7 ± 1.7‰. The plume scale approach integrates across the typical U.S. fleet giving a representative value that can be used for tracking the impact of this emission source in the environment. NH3 also tends towards a narrow isotopic range when considered at the roadside scale compared to individual vehicles. In agricultural settings, the isotopes of NOx and HONO released from soils under different fertilizer practices is typically very negative in δ15N (-40 to -10‰) and appears to vary most with soil N properties rather than meteorology. Our work is now extending to discern sources influencing Nr deposition in an urban area at the head of New England's largest estuary. National monitoring of N deposition shows decreases in NO3- (but not NH4+) deposition over the last two decades, following better controls on NOx emissions. Wet deposition collected in an urban area exhibits N concentrations that are often 3-5 times higher than that found in regional monitoring networks. An event-based, year-round record of the isotopic composition of NO3- and NH4+ in wet deposition is currently underway with the aim of constraining local versus transported emissions sources and understanding the implications of very concentrated deposition events on a major urban watershed.

TRANSPORT

EPA Science Inventory

Presentation outline: transport principles, effective solubility; gasoline composition; and field examples (plume diving).
Presentation conclusions: MTBE transport follows from - phyiscal and chemical properties and hydrology. Field examples show: MTBE plumes > benzene plu...

Volcanic Plume Measurements with UAV (Invited)

NASA Astrophysics Data System (ADS)

Shinohara, H.; Kaneko, T.; Ohminato, T.

2013-12-01

Volatiles in magmas are the driving force of volcanic eruptions and quantification of volcanic gas flux and composition is important for the volcano monitoring. Recently we developed a portable gas sensor system (Multi-GAS) to quantify the volcanic gas composition by measuring volcanic plumes and obtained volcanic gas compositions of actively degassing volcanoes. As the Multi-GAS measures variation of volcanic gas component concentrations in the pumped air (volcanic plume), we need to bring the apparatus into the volcanic plume. Commonly the observer brings the apparatus to the summit crater by himself but such measurements are not possible under conditions of high risk of volcanic eruption or difficulty to approach the summit due to topography etc. In order to overcome these difficulties, volcanic plume measurements were performed by using manned and unmanned aerial vehicles. The volcanic plume measurements by manned aerial vehicles, however, are also not possible under high risk of eruption. The strict regulation against the modification of the aircraft, such as installing sampling pipes, also causes difficulty due to the high cost. Application of the UAVs for the volcanic plume measurements has a big advantage to avoid these problems. The Multi-GAS consists of IR-CO2 and H2O gas analyzer, SO2-H2O chemical sensors and H2 semiconductor sensor and the total weight ranges 3-6 kg including batteries. The necessary conditions of the UAV for the volcanic plumes measurements with the Multi-GAS are the payloads larger than 3 kg, maximum altitude larger than the plume height and installation of the sampling pipe without contamination of the exhaust gases, as the exhaust gases contain high concentrations of H2, SO2 and CO2. Up to now, three different types of UAVs were applied for the measurements; Kite-plane (Sky Remote) at Miyakejima operated by JMA, Unmanned airplane (Air Photo Service) at Shinomoedake, Kirishima volcano, and Unmanned helicopter (Yamaha) at Sakurajima volcano operated by ERI, Tokyo University. In all cases, we could estimated volcanic gas compositions, such as CO2/SO2 ratios, but also found out that it is necessary to improve the techniques to avoid the contamination of the exhaust gases and to approach more concentrated part of the plume. It was also revealed that the aerial measurements have an advantage of the stable background. The error of the volcanic gas composition estimates are largely due to the large fluctuation of the atmospheric H2O and CO2 concentrations near the ground. The stable atmospheric background obtained by the UAV measurements enables accurate estimate of the volcanic gas compositions. One of the most successful measurements was that on May 18, 2011 at Shinomoedake, Kirishima volcano during repeating Vulcanian eruption stage. The major component composition was obtained as H2O=97, CO2=1.5, SO2=0.2, H2S=0.24, H2=0.006 mol%; the high CO2 contents suggests relatively deep source of the magma degassing and the apparent equilibrium temperature obtained as 400°C indicates that the gas was cooled during ascent to the surface. The volcanic plume measurement with UAV will become an important tool for the volcano monitoring that provides important information to understand eruption processes.

Petrological processes in mantle plume heads: Evidence from study of mantle xenoliths in the late Cenozoic alkali Fe-Ti basalts in Western Syria

NASA Astrophysics Data System (ADS)

Sharkov, Evgenii

2015-04-01

It is consensus now that within-plate magmatism is considered with ascending of mantle plumes and adiabatic melting of their head. At the same time composition of the plumes' matter and conditions of its adiabatic melting are unclear yet. The major source of objective information about it can be mantle xenoliths in alkali basalts and basanites which represent fragments of material of the plume heads above magma-generation zone. They are not represent material in melting zone, however, carry important information about material of modern mantle plumes, its phase composition and components, involved in melting. Populations of mantle xenoliths in basalts are characterized by surprising sameness in the world and represented by two major types: (1) dominated rocks of ``green'' series, and (2) more rare rocks of ``black'' series, which formed veins in the ``green'' series matrix. It can evidence about common composition of plume material in global scale. In other words, the both series of xenoliths represent two types of material of thermochemical mantle plumes, ascended from core-mantle boundary (Maruyama, 1994; Dobretsov et al., 2001). The same types of xenoliths are found in basalts and basanites of Western Syria (Sharkov et al., 1996). Rocks of ``green'' series are represented by Sp peridotites with cataclastic and protogranular structures and vary in composition from dominated spinel lherzolites to spinel harzburgites and rare spinel pyroxenites (websterites). It is probably evidence about incomplete homogenizing of the plume head matter, where material, underwent by partial melting, adjoins with more fertile material. Such heterogeneity was survived due to quick cooling of upper rim of the plume head in contact with relatively cold lithosphere. Essential role among xenoliths of the ``black'' series play Al-Ti-augite and water-bearing phases like hornblende (kaersutute) and Ti-phlogopite. Rocks of this series are represented by wehrlite, clinopyroxenite, amphibole clinopyroxenite, hornbledite, etc. as well as megacrysts of Al-Ti-augite, kaersutite, ilmenite, sanidine, etc. Numerous vesicles often occurred in megacrysts, especially in kaersurtite. Sp peridotites of the matrix are sharply different on their geochemical features from the ``black series'' rocks (in this case, megacrysts of kaersutite) which are the most close to composition of xenoliths-bearing alkali basalts. From this follows that geochemistry of plume-related basalts was determined by mantle fluids which occurred in magma-generation zone. Very likely, that these fluids, enriched in Fe, Ti, LREE, alkalis, and incompatible elements, initially were parts of intergranular material of original mantle plume material and were released due to its decompression. Because their high mobility, the fluids percolated upwards and accumulated in the upper part of the mantle plume head, where promoted its melting by lowering of solidus of the matter. Excess of the fluids gathered beneath the cooled upper rim and penetrated in its rocks which led to appearance of centers of secondary melting (melt-pockets). Very likely, that these secondary melts formed rocks of the ``black series'' (Ismail et al., 2008;Ryabchkov et al., 2011; Ma et al., 2014). According to geobarometric estimations, Sp peridotite xenoliths from Syria derived from depths 24-42 km (0.8-1.4 GPa) under temperatures 896-980oC; formation of melt-pockets, enriched in volatiles, occurred at the depths 21-27 km (0.7-0.9 GPa) under 826-981oC (Sharkov et al., 1996; Ismail et al., 2008; Ma et al., 2014). From this follows that plumeheads reached depths approximately 21-30 km which is in agree with practically absence of lower-crustal xenoliths in the populations. One of the problems of plume-related magmatism is coexisting of alkali and tholeiitic basalts, which origin often considered with different PT conditions. However, these basalt not rarely interlayered, especially at low and middle levels of LIPs or in single volcanoes (Hawaii, Etna, etc.) which is not in a good agreement with such idea. We suggest that the situation can be more likely explained by nonuniform impregnation of peridotite matrix with fluid components which composition and/or quantity can play essential role in composition of smeltings. It is especially important because even small differences in their ñomposition near to plane of SiO2 saturation in ``basalt tetrahedron'' (Yoder and Tilley, 1962) lead to appearance of Ne-normative or Ne-free melts at practically similar PT conditions. Thus, judging on composition of the mantle xenoliths in basalts of all occurrences in the world, quite possible that Sp peridotites (mainly lherzolites) together with intergranular geochemical-enriched fluid components represent the matter of the modern thermochemical mantle plumes. Origin of two major types of the plume-related magmas, probably, considered with fluid regime in the plume head.

Remote laser evaporative molecular absorption spectroscopy

NASA Astrophysics Data System (ADS)

Hughes, Gary B.; Lubin, Philip; Cohen, Alexander; Madajian, Jonathan; Kulkarni, Neeraj; Zhang, Qicheng; Griswold, Janelle; Brashears, Travis

2016-09-01

We describe a novel method for probing bulk molecular and atomic composition of solid targets from a distant vantage. A laser is used to melt and vaporize a spot on the target. With sufficient flux, the spot temperature rises rapidly, and evaporation of surface materials occurs. The melted spot creates a high-temperature blackbody source, and ejected material creates a plume of surface materials in front of the spot. Molecular and atomic absorption occurs as the blackbody radiation passes through the ejected plume. Bulk molecular and atomic composition of the surface material is investigated by using a spectrometer to view the heated spot through the ejected plume. The proposed method is distinct from current stand-off approaches to composition analysis, such as Laser-Induced Breakdown Spectroscopy (LIBS), which atomizes and ionizes target material and observes emission spectra to determine bulk atomic composition. Initial simulations of absorption profiles with laser heating show great promise for Remote Laser-Evaporative Molecular Absorption (R-LEMA) spectroscopy. The method is well-suited for exploration of cold solar system targets—asteroids, comets, planets, moons—such as from a spacecraft orbiting the target. Spatial composition maps could be created by scanning the surface. Applying the beam to a single spot continuously produces a borehole or trench, and shallow subsurface composition profiling is possible. This paper describes system concepts for implementing the proposed method to probe the bulk molecular composition of an asteroid from an orbiting spacecraft, including laser array, photovoltaic power, heating and ablation, plume characteristics, absorption, spectrometry and data management.

Phytoplankton assemblages within the Chesapeake Bay plume and adjacent waters of the continental shelf

NASA Technical Reports Server (NTRS)

Marshall, H. G.

1981-01-01

The Chesapeake Bay plume was identified and plotted in relation to the presence and high concentrations of phytoplankton assemblages. Seasonal differences occurred within the plume during the collection period, with Skeletonema costatum and an ultraplankton component the dominant forms. Patchiness was found along the transects, with variations in composition and concentrations common on consecutive day sampling within the plume in its movement along the shelf. The presence of 236 species is noted, with their presence indicated for plume and shelf stations during the March, June, and October 1980 collections.

Atmospheric evolution of sulfur emissions from Kı̅lauea: real-time measurements of oxidation, dilution, and neutralization within a volcanic plume.

PubMed

Kroll, Jesse H; Cross, Eben S; Hunter, James F; Pai, Sidhant; Wallace, Lisa M M; Croteau, Philip L; Jayne, John T; Worsnop, Douglas R; Heald, Colette L; Murphy, Jennifer G; Frankel, Sheila L

2015-04-07

The high atmospheric concentrations of toxic gases, particulate matter, and acids in the areas immediately surrounding volcanoes can have negative impacts on human and ecological health. To better understand the atmospheric fate of volcanogenic emissions in the near field (in the first few hours after emission), we have carried out real-time measurements of key chemical components of the volcanic plume from Kı̅lauea on the Island of Hawai'i. Measurements were made at two locations, one ∼ 3 km north-northeast of the vent and the other 31 km to the southwest, with sampling at each site spanning a range of meteorological conditions and volcanic influence. Instrumentation included a sulfur dioxide monitor and an Aerosol Chemical Speciation Monitor, allowing for a measurement of the partitioning between the two major sulfur species (gas-phase SO2 and particulate sulfate) every 5 min. During trade wind conditions, which sent the plume toward the southwest site, sulfur partitioning exhibited a clear diurnal pattern, indicating photochemical oxidation of SO2 to sulfate; this enabled the quantitative determination of plume age (5 h) and instantaneous SO2 oxidation rate (2.4 × 10(-6) s(-1) at solar noon). Under stagnant conditions near the crater, the extent of SO2 oxidation was substantially higher, suggesting faster oxidation. The particles within the plume were extremely acidic, with pH values (controlled largely by ambient relative humidity) as low as -0.8 and strong acidity (controlled largely by absolute sulfate levels) up to 2200 nmol/m(3). The high variability of sulfur partitioning and particle composition underscores the chemically dynamic nature of volcanic plumes, which may have important implications for human and ecological health.

Propulsion

NASA Astrophysics Data System (ADS)

Smith, P. K.

1993-06-01

Current requirements for missile systems increasingly stress the need for stealth capability. For the majority of missile systems and missions, the exhaust plume is likely to be the major contributor to overall missile signature, especially considering the recent developments in low emission and low Radar Cross Section coatings for motor bodies. This implies the need for the lowest possible rocket exhaust signature over a wide range of frequencies from the UV through visible and IR to microwave and radio frequencies. The choice of propellant type, Double Base; Composite etc, plays a significant part in determining the exhaust signature of the rocket motor as does the selection of inert materials for liners, inhibitors, and nozzles. It is also possible with certain propellants to incorporate additives which reduce exhaust signature either by modifying the chemistry or the afterburning plume or more significantly by suppressing secondary combustion and hence dramatically reducing plume temperature. The feasibility of plume signature control on the various missions envisaged by the missile designer is considered. The choice of propellant type and hardware components to give low signature is discussed together with performance implications. Signature reduction results obtained over a wide range of frequencies are also presented.

Plume-exit modeling to determine cloud condensation nuclei activity of aerosols from residential biofuel combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mena, Francisco; Bond, Tami C.; Riemer, Nicole

Residential biofuel combustion is an important source of aerosols and gases in the atmosphere. The change in cloud characteristics due to biofuel burning aerosols is uncertain, in part, due to the uncertainty in the added number of cloud condensation nuclei (CCN) from biofuel burning. We provide estimates of the CCN activity of biofuel burning aerosols by explicitly modeling plume dynamics (coagulation, condensation, chemical reactions, and dilution) in a young biofuel burning plume from emission until plume exit, defined here as the condition when the plume reaches ambient temperature and specific humidity through entrainment. We found that aerosol-scale dynamics affect CCNmore » activity only during the first few seconds of evolution, after which the CCN efficiency reaches a constant value. Homogenizing factors in a plume are co-emission of semi-volatile organic compounds (SVOCs) or emission at small particle sizes; SVOC co-emission can be the main factor determining plume-exit CCN for hydrophobic or small particles. Coagulation limits emission of CCN to about 10 16 per kilogram of fuel. Depending on emission factor, particle size, and composition, some of these particles may not activate at low supersaturation ( s sat). Hygroscopic Aitken-mode particles can contribute to CCN through self-coagulation but have a small effect on the CCN activity of accumulation-mode particles, regardless of composition differences. Simple models (monodisperse coagulation and average hygroscopicity) can be used to estimate plume-exit CCN within about 20 % if particles are unimodal and have homogeneous composition, or when particles are emitted in the Aitken mode even if they are not homogeneous. On the other hand, if externally mixed particles are emitted in the accumulation mode without SVOCs, an average hygroscopicity overestimates emitted CCN by up to a factor of 2. This work has identified conditions under which particle populations become more homogeneous during plume processes. This homogenizing effect requires the components to be truly co-emitted, rather than sequentially emitted.« less

Plume-exit modeling to determine cloud condensation nuclei activity of aerosols from residential biofuel combustion

NASA Astrophysics Data System (ADS)

Mena, Francisco; Bond, Tami C.; Riemer, Nicole

2017-08-01

Residential biofuel combustion is an important source of aerosols and gases in the atmosphere. The change in cloud characteristics due to biofuel burning aerosols is uncertain, in part, due to the uncertainty in the added number of cloud condensation nuclei (CCN) from biofuel burning. We provide estimates of the CCN activity of biofuel burning aerosols by explicitly modeling plume dynamics (coagulation, condensation, chemical reactions, and dilution) in a young biofuel burning plume from emission until plume exit, defined here as the condition when the plume reaches ambient temperature and specific humidity through entrainment. We found that aerosol-scale dynamics affect CCN activity only during the first few seconds of evolution, after which the CCN efficiency reaches a constant value. Homogenizing factors in a plume are co-emission of semi-volatile organic compounds (SVOCs) or emission at small particle sizes; SVOC co-emission can be the main factor determining plume-exit CCN for hydrophobic or small particles. Coagulation limits emission of CCN to about 1016 per kilogram of fuel. Depending on emission factor, particle size, and composition, some of these particles may not activate at low supersaturation (ssat). Hygroscopic Aitken-mode particles can contribute to CCN through self-coagulation but have a small effect on the CCN activity of accumulation-mode particles, regardless of composition differences. Simple models (monodisperse coagulation and average hygroscopicity) can be used to estimate plume-exit CCN within about 20 % if particles are unimodal and have homogeneous composition, or when particles are emitted in the Aitken mode even if they are not homogeneous. On the other hand, if externally mixed particles are emitted in the accumulation mode without SVOCs, an average hygroscopicity overestimates emitted CCN by up to a factor of 2. This work has identified conditions under which particle populations become more homogeneous during plume processes. This homogenizing effect requires the components to be truly co-emitted, rather than sequentially emitted.

Plume-exit modeling to determine cloud condensation nuclei activity of aerosols from residential biofuel combustion

DOE PAGES

Mena, Francisco; Bond, Tami C.; Riemer, Nicole

2017-08-07

Residential biofuel combustion is an important source of aerosols and gases in the atmosphere. The change in cloud characteristics due to biofuel burning aerosols is uncertain, in part, due to the uncertainty in the added number of cloud condensation nuclei (CCN) from biofuel burning. We provide estimates of the CCN activity of biofuel burning aerosols by explicitly modeling plume dynamics (coagulation, condensation, chemical reactions, and dilution) in a young biofuel burning plume from emission until plume exit, defined here as the condition when the plume reaches ambient temperature and specific humidity through entrainment. We found that aerosol-scale dynamics affect CCNmore » activity only during the first few seconds of evolution, after which the CCN efficiency reaches a constant value. Homogenizing factors in a plume are co-emission of semi-volatile organic compounds (SVOCs) or emission at small particle sizes; SVOC co-emission can be the main factor determining plume-exit CCN for hydrophobic or small particles. Coagulation limits emission of CCN to about 10 16 per kilogram of fuel. Depending on emission factor, particle size, and composition, some of these particles may not activate at low supersaturation ( s sat). Hygroscopic Aitken-mode particles can contribute to CCN through self-coagulation but have a small effect on the CCN activity of accumulation-mode particles, regardless of composition differences. Simple models (monodisperse coagulation and average hygroscopicity) can be used to estimate plume-exit CCN within about 20 % if particles are unimodal and have homogeneous composition, or when particles are emitted in the Aitken mode even if they are not homogeneous. On the other hand, if externally mixed particles are emitted in the accumulation mode without SVOCs, an average hygroscopicity overestimates emitted CCN by up to a factor of 2. This work has identified conditions under which particle populations become more homogeneous during plume processes. This homogenizing effect requires the components to be truly co-emitted, rather than sequentially emitted.« less

Long-Lived Mantle Plumes Sample Multiple Deep Mantle Geochemical Domains: The Example of the Hawaiian-Emperor Chain

NASA Astrophysics Data System (ADS)

Harrison, L.; Weis, D.

2017-12-01

Oceanic island basalts provide the opportunity for the geochemist to study the deep mantle source removed from continental sources of contamination and, for long-lived systems, the evolution of mantle sources with time. In the case of the Hawaiian-Emperor (HE) chain, formation by a long-lived (>81 Myr), deeply-sourced mantle plume allows for insight into plume dynamics and deep mantle geochemistry. The geochemical record of the entire chain is now complete with analysis of Pb-Hf-Nd-Sr isotopes and elemental compositions of the Northwest Hawaiian Ridge (NWHR), which consists of 51 volcanoes spanning 42 Ma between the bend in the chain and the Hawaiian Islands. This segment of the chain previously represented a significant data gap where Hawaiian plume geochemistry changed markedly, along with magmatic flux: only Kea compositions have been observed on Emperor seamounts (>50 Ma), whereas the Hawaiian Islands (<6 Ma) present both Kea and Loa compositions. A database of 700 Hawaiian Island shield basalts Pb-Hf-Nd-Sr isotopic compositions were compiled to construct a logistical regression model of Loa or Kea affinity that sorts data into a dichotomous category and provides insight into the relationship between independent variables. We use this model to predict whether newly analyzed NWHR samples are Loa or Kea composition based on their Pb-Sr-Nd-Hf isotopic compositions. The logistical regression model is significantly better at prediciting Loa or Kea affinity than the constant only model (χ2=263.3, df=4, p<0.0001), with Pb and Sr isotopes providing the most predicitive power. Daikakuji, West Nihoa, Nihoa, and Mokumanamana erupt Loa-type lavas, suggesting that the Loa source is sampled ephemerally during the NWHR and increases in presence and volume towards the younger section of the NWHR (younger than Midway 20-25 Ma). These results complete the picture of Hawaiian mantle plume geochemistry and geodynamics for 81 Myr, and show that the Hawaiian mantle plume has transitioned from a dominately Kea source during the Emperor seamounts and older NWHR to an increasingly enriched Loa source from the mid NWHR to Hawaiian Islands. We propose this is due to Hawaiian mantle plume drift through different lower mantle geohemical domains.

Mobility of plume-derived volcanogenic elements in meteoric water at Nyiragongo volcano (Congo) inferred from the chemical composition of single rainfall events

NASA Astrophysics Data System (ADS)

Liotta, Marcello; Shamavu, Patient; Scaglione, Sarah; D'Alessandro, Walter; Bobrowski, Nicole; Bruno Giuffrida, Giovanni; Tedesco, Dario; Calabrese, Sergio

2017-11-01

The chemical composition of single rainfall events was investigated at Nyiragongo volcano (Democratic Republic of Congo) with the aim of determining the relative contributions of plume-derived elements. The different locations of the sampling sites allowed both plume-affected samples (hereafter referred to as ;fumigated samples;) and samples representative of the local background to be collected. The chemical composition of the local background reflects the peculiar geographic features of the area, being influenced by biomass burning, geogenic dust, and biological activity. Conversely, fumigated samples contain large amounts of volcanogenic elements that can be clearly distinguished from the local background. These elements are released into the atmosphere from the persistently boiling lava lake of the Nyiragongo crater and from the neonate lava lake of Nyamulagira. These emissions result in a volcanic plume that includes solid particles, acidic droplets, and gaseous species. The chemical signature of the volcanic emissions appears in falling raindrops as they interact with the plume. HCl and HBr readily dissolve in water, and so their ratio in rain samples reflects that of the volcanic plume. The transport of HF is mediated by the large amount of silicate particles generated at the magma-air interface. SO2 is partially converted into SO42- that dissolves in water. The refractory elements dissolved in rain samples derive from the dissolution of silicate particles, and most of them (Al, Mg, Ca, and Sr) are present at exactly the same molar ratios as in the rocks. In contrast, elements such as Na, K, Rb, Cu, and Pb are enriched relative to the whole-rock composition, suggesting that they are volatilized during magma degassing. After correcting for the dissolution of silicate particles, we can define that the volatility of the elements decreases in the following order: Pb ≫ Rb > K > Na. This finding, which is the first for a volcanic plume, is consistent with previous measurements in high-temperature fumaroles at other volcanic areas.

Characteristics and Influence of Biosmoke on the Fine-Particle Ionic Composition Measured in Asian Outflow during the Transport and Chemical Evolution Over the Pacific (TRACE-P) Experiment

NASA Technical Reports Server (NTRS)

Ma, Y.; Weber, R. J.; Lee, Y.-N.; Orsini, D. A.; Maxwell-Meier, K.; Thornton, D. C.; Bandy, A. R.; Clarke, A. D.; Blake, D. R.; Sachse, G. W.

2003-01-01

We investigate the sources, prevalence, and fine-particle inorganic composition of biosmoke over the western Pacific Ocean between 24 February and 10 April 2001. The analysis is based on highly time-resolved airborne measurements of gaseous and fine- particle inorganic chemical composition made during the NASA Transport and Chemical Evolution over the Pacific (TRACE-P) experiment. At latitudes below approximately 25 deg. N, relatively pure biomass burning plumes of enhanced fine-particle potassium, nitrate, ammonium, light-absorbing aerosols, and CO concentrations were observed in plumes that back trajectories and satellite fire map data suggest originated from biomass burning in southeast Asia. Fine-particle water-soluble potassium (K+) is confirmed to be a unique biosmoke tracer, and its prevalence throughout the experiment indicates that approximately 20% of the TRACE-P Asian outflow plumes were influenced, to some extent, by biomass or biofuel burning emissions. At latitudes above 25 deg. N, highly mixed urban/industrial and biosmoke plumes, indicated by SO(sup 2, sub 4) and K+, were observed in 5 out of 53 plumes. Most plumes were found in the Yellow Sea and generally were associated with much higher fine-particle loadings than plumes lacking a biosmoke influence. The air mass back trajectories of these mixed plumes generally pass through the latitude range of between 34 deg. and 40 deg. N on the eastern China coast, a region that includes the large urban centers of Beijing and Tianjin. A lack of biomass burning emissions based on fire maps and high correlations between K+ and pollution tracers (e.g., S(sup 2, sub 4) suggest biofuel sources. Ratios of fine-particle potassium to sulfate are used to provide an estimate of relative contributions of biosmoke emissions to the mixed Asian plumes. The ratio is highly correlated with fine-particle volume (r(sup 2) = 0.85) and predicts that for the most polluted plume encounter in TRACE-P, approximately 60% of the plume is associated with biosmoke emissions. On average, biosmoke contributes approximately 35-40% to the measured fine inorganic aerosol mass in the mixed TRACE-P plumes intercepted north of 25% latitude.

Comparing the composition of the earliest basalts erupted by the Iceland and Afar mantle plumes.

NASA Astrophysics Data System (ADS)

Stuart, Finlay M.

2013-04-01

The first basalts erupted by mantle plumes are typically generated by mantle melting at temperatures 200-300°C higher than average ambient mantle. This is consistent with the derivation of from a thermal boundary layer at the core-mantle boundary. Mantle plume temperatures decrease with time, likely as large plume heads give way to thin plume conduits. Consequently the early, hot plume basalts are a window into the deep mantle. At it's simplest they provide a test of whether the discrete plume source regions are primordial mantle that have been isolated since soon after Earth accretion, or have substantial contributions from subducted slabs. Here I present new isotopic and trace element determinations of the earliest picritic basalts from the ~30 Ma Afar plume in Ethiopia. They will be compared with similar material from the ~60 Ma proto-Iceland plume (PIP) in an effort to test prevailing models regarding the source of mantle plumes. The extremely primordial nature of the helium in the PIP picrites (3He/4He ~ 50 Ra) contrasts with much lower values of the Ethiopian flood basalt province (~21 Ra). The Iceland plume 3He/4He has decreased (linearly) with time, mirroring the secular cooling of the Iceland mantle plume identified by decreasing MgO and FeO in primary melts. In 60 million years the Iceland plume 3He/4He is still higher than the maximum Afar plume value. The Sr-Nd-Pb isotopic composition of the high 3He/4He Ethiopian flood basalt province picrites are remarkably homogenous (e.g. 87Sr/86Sr = 0.70396-0.70412; 206Pb/204Pb = 18.82-19.01). In comparison the PIP picrites have ranges that span nearly the global range of E-MORB and N-MORB. The Afar and proto-Iceland mantle plumes are clearly not initiated in a single deep mantle domain with the same depletion/enrichment and degassing histories, and the same scale of heterogeneity. This implies that there is more than one plume source region/mechanism that is capable of generating comparable volumes of basalt melt at Earth surface.

Tectonic events, continental intraplate volcanism, and mantle plume activity in northern Arabia: Constraints from geochemistry and Ar-Ar dating of Syrian lavas

NASA Astrophysics Data System (ADS)

Krienitz, M.-S.; Haase, K. M.; Mezger, K.; van den Bogaard, P.; Thiemann, V.; Shaikh-Mashail, M. A.

2009-04-01

New 40Ar/39Ar ages combined with chemical and Sr, Nd, and Pb isotope data for volcanic rocks from Syria along with published data of Syrian and Arabian lavas constrain the spatiotemporal evolution of volcanism, melting regime, and magmatic sources contributing to the volcanic activity in northern Arabia. Several volcanic phases occurred in different parts of Syria in the last 20 Ma that partly correlate with different tectonic events like displacements along the Dead Sea Fault system or slab break-off beneath the Bitlis suture zone, although the large volume of magmas and their composition suggest that hot mantle material caused volcanism. Low Ce/Pb (<20), Nb/Th (<10), and Sr, Nd, and Pb isotope variations of Syrian lavas indicate the role of crustal contamination in magma genesis, and contamination of magmas with up to 30% of continental crustal material can explain their 87Sr/86Sr. Fractionation-corrected major element compositions and REE ratios of uncontaminated lavas suggest a pressure-controlled melting regime in western Arabia that varies from shallow and high-degree melt formation in the south to increasingly deeper regions and lower extents of the beginning melting process northward. Temperature estimates of calculated primary, crustally uncontaminated Arabian lavas indicate their formation at elevated mantle temperatures (Texcess ˜ 100-200°C) being characteristic for their generation in a plume mantle region. The Sr, Nd, and Pb isotope systematic of crustally uncontaminated Syrian lavas reveal a sublithospheric and a mantle plume source involvement in their formation, whereas a (hydrous) lithospheric origin of lavas can be excluded on the basis of negative correlations between Ba/La and K/La. The characteristically high 206Pb/204Pb (˜19.5) of the mantle plume source can be explained by material entrainment associated with the Afar mantle plume. The Syrian volcanic rocks are generally younger than lavas from the southern Afro-Arabian region, indicating a northward progression of the commencing volcanism since the arrival of the Afar mantle plume beneath Ethiopia/Djibouti some 30 Ma ago. The distribution of crustally uncontaminated high 206Pb/204Pb lavas in Arabia indicates a spatial influence of the Afar plume of ˜2600 km in northward direction with an estimated flow velocity of plume material on the order of 22 cm/a.

Genome-resolved metagenomics reveals that sulfur metabolism dominates the microbial ecology of rising hydrothermal plumes

NASA Astrophysics Data System (ADS)

Anantharaman, K.; Breier, J. A., Jr.; Jain, S.; Reed, D. C.; Dick, G.

2015-12-01

Deep-sea hydrothermal plumes occur when hot fluids from hydrothermal vents replete with chemically reduced elements and compounds like sulfide, methane, hydrogen, ammonia, iron and manganese mix with cold, oxic seawater. Chemosynthetic microbes use these reduced chemicals to power primary production and are pervasive throughout the deep sea, even at sites far removed from hydrothermal vents. Although neutrally-buoyant hydrothermal plumes have been well-studied, rising hydrothermal plumes have received little attention even though they represent an important interface in the deep-sea where microbial metabolism and particle formation processes control the transformation of important elements and impact global biogeochemical cycles. In this study, we used genome-resolved metagenomic analyses and thermodynamic-bioenergetic modeling to study the microbial ecology of rising hydrothermal plumes at five different hydrothermal vents spanning a range of geochemical gradients at the Eastern Lau Spreading Center (ELSC) in the Western Pacific Ocean. Our analyses show that differences in the geochemistry of hydrothermal vents do not manifest in microbial diversity and community composition, both of which display only minor variance across ELSC hydrothermal plumes. Microbial metabolism is dominated by oxidation of reduced sulfur species and supports a diversity of bacteria, archaea and viruses that provide intriguing insights into metabolic plasticity and virus-mediated horizontal gene transfer in the microbial community. The manifestation of sulfur oxidation genes in hydrogen and methane oxidizing organisms hints at metabolic opportunism in deep-sea microbes that would enable them to respond to varying redox conditions in hydrothermal plumes. Finally, we infer that the abundance, diversity and metabolic versatility of microbes associated with sulfur oxidation impart functional redundancy that could allow it to persist in the dynamic settings of hydrothermal plumes.

The composition and distribution of the rejuvenated component across the Hawaiian plume: Hf-Nd-Sr-Pb isotope systematics of Kaula lavas and pyroxenite xenoliths

NASA Astrophysics Data System (ADS)

Bizimis, Michael; Salters, Vincent J. M.; Garcia, Michael O.; Norman, Marc D.

2013-10-01

Rejuvenated volcanism refers to the reemergence of volcanism after a hiatus of 0.5-2 Ma following the voluminous shield building stage of Hawaiian volcanoes. The composition of the rejuvenated source and its distribution relative to the center of the plume provide important constraints on the origin of rejuvenated volcanism. Near-contemporaneous lavas from the Kaula-Niihau-Kauai ridge and the North Arch volcanic field that are aligned approximately orthogonally to the plume track can constrain the lateral geochemical heterogeneity and distribution of the rejuvenated source across the volcanic chain. Nephelinites, phonolites and pyroxenite xenoliths from Kaula Island have radiogenic Hf, Nd and unradiogenic Sr isotope compositions consistent with a time-integrated depleted mantle source. The pyroxenites and nephelinites extend to the lowest 208Pb/204Pb reported in Hawaiian rocks. These data, along with new Pb isotope data from pyroxenites from the Salt Lake Crater (Oahu) redefine the composition of the depleted end-member of the Hawaiian rejuvenated source at 208Pb/204Pb=37.35±0.05, 206Pb/204Pb = 17.75±0.03, ɛNd = 9-10, ɛHf ˜16-17 and 87Sr/88Sr <0.70305. The revised isotope composition also suggests that this depleted component may contribute to LOA and KEA trend shield stage Hawaiian lavas, consistent with the rejuvenated source being part of the Hawaiian plume and not entrained upper mantle. The isotope systematics of rejuvenated magmas along the Kaula-Niihau-Kauai-North Arch transect are consistent with a larger proportion of the rejuvenated depleted component in the periphery of the plume track rather than along its axis.

Carbon isotope systematics of Turrialba volcano, Costa Rica, using a portable cavity ring-down spectrometer

NASA Astrophysics Data System (ADS)

Malowany, K. S.; Stix, J.; de Moor, J. M.; Chu, K.; Lacrampe-Couloume, G.; Sherwood Lollar, B.

2017-07-01

Over the past two decades, activity at Turrialba volcano, Costa Rica, has shifted from hydrothermal to increasingly magmatic in character, with enhanced degassing and eruption potential. We have conducted a survey of the δ13C signatures of gases at Turrialba using a portable field-based CRDS with comparison to standard IRMS techniques. Our δ13C results of the volcanic plume, high-temperature vents, and soil gases reveal isotopic heterogeneity in the CO2 gas composition at Turrialba prior to its recent phase of eruptive activity. The isotopic value of the regional fault system, Falla Ariete (-3.4 ± 0.1‰), is in distinct contrast with the Central crater gases (-3.9 ± 0.1‰) and the 2012 high-temperature vent (-4.4 ± 0.2‰), an indication that spatial variability in δ13C may be linked to hydrothermal transport of volcanic gases, heterogeneities in the source composition, or magmatic degassing. Isotopic values of CO2 samples collected in the plume vary from δ13C of -5.2 to -10.0‰, indicative of mixing between atmospheric CO2 (-9.2 ± 0.1‰), and a volcanic source. We compare the Keeling method to a traditional mixing model (hyperbolic mixing curve) to estimate the volcanic source composition at Turrialba from the plume measurements. The predicted source compositions from the Keeling and hyperbolic methods (-3.0 ± 0.5‰ and -3.9 ± 0.4‰, respectively) illustrate two potential interpretations of the volcanic source at Turrialba. As of the 29 October 2014, Turrialba has entered a new eruptive period, and continued monitoring of the summit gases for δ13C should be conducted to better understand the dominant processes controlling δ13C fractionation at Turrialba.

The planet beyond the plume hypothesis

NASA Astrophysics Data System (ADS)

Smith, Alan D.; Lewis, Charles

1999-12-01

Acceptance of the theory of plate tectonics was accompanied by the rise of the mantle plume/hotspot concept which has come to dominate geodynamics from its use both as an explanation for the origin of intraplate volcanism and as a reference frame for plate motions. However, even with a large degree of flexibility permitted in plume composition, temperature, size, and depth of origin, adoption of any limited number of hotspots means the plume model cannot account for all occurrences of the type of volcanism it was devised to explain. While scientific protocol would normally demand that an alternative explanation be sought, there have been few challenges to "plume theory" on account of a series of intricate controls set up by the plume model which makes plumes seem to be an essential feature of the Earth. The hotspot frame acts not only as a reference but also controls plate tectonics. Accommodating plumes relegates mantle convection to a weak, sluggish effect such that basal drag appears as a minor, resisting force, with plates having to move themselves by boundary forces and continents having to be rifted by plumes. Correspondingly, the geochemical evolution of the mantle is controlled by the requirement to isolate subducted crust into plume sources which limits potential buffers on the composition of the MORB-source to plume- or lower mantle material. Crustal growth and Precambrian tectonics are controlled by interpretations of greenstone belts as oceanic plateaus generated by plumes. Challenges to any aspect of the plume model are thus liable to be dismissed unless a counter explanation is offered across the geodynamic spectrum influenced by "plume theory". Nonetheless, an alternative synthesis can be made based on longstanding petrological evidence for derivation of intraplate volcanism from volatile-bearing sources (wetspots) in conjunction with concepts dismissed for being incompatible or superfluous to "plume theory". In the alternative Earth, the sources for intraplate volcanism evolve from the source residues of arc volcanism located along sutures in the continental mantle. Continental rifting and the lateral distribution of intraplate sources in the asthenosphere are controlled by Earth rotation. Shear induced on the base of the asthenosphere from the mesosphere as the Earth rotates is transmitted to the lithosphere as basal drag. Attenuation of the drag due to the low viscosity of the asthenosphere, in conjunction with plate motions from boundary forces, results in a rotation differential of up to 5 cm yr -1 between the lithosphere and mesosphere manifest as westward plate lag/eastward mantle flow. Continental rifting results from basal drag supplemented by local convection induced by lithospheric architecture. Large continental igneous provinces are generated by convective melting, with passive margin volcanic sequences following the axis of rifting and flood basalts overlying the intersection of sutures in the continental mantle. As rifting progresses, the convection cells expand, cycling continental mantle from sutures perpendicular to the rift axis to generate intraplate tracks in the ocean basin. Continental mantle not melted on rifting, or delaminated on continental collision, becomes displaced to the east of the continent by differential rotation, which also sets up a means for tapping the material to give fixed melting anomalies. When plates move counter to the Earth's rotation, as in the example of the Pacific plate, asthenospheric flow is characterised by a counterflow regime with a zero velocity layer at depths within the stability field for volatile-bearing minerals. Intraplate volcanism results when melts are tapped from this stationary layer along lithospheric stress trajectories induced by stressing of the plate from variations in the subduction geometry around the margins of the plate. Plate boundary forces acting in the same direction as Earth rotation, as for the Nazca plate, produce fast plate velocities but not counterflow, though convergent margin geometry may still induce propagating fractures which set up melting anomalies. Lateral migration of asthenospheric domains allows the sources of Pacific intraplate volcanism to be traced back to continental mantle eroded during the breakup of Gondwana and the amalgamation of Asia in the Paleozoic. Intraplate volcanism in the South Pacific therefore has a common Gondwanan origin to intraplate volcanism in the South Atlantic and Indian Oceans, hence the DUPAL anomaly is entirely of shallow origin. Such domains constitute a second order geochemical heterogeneity superimposed on a streaky/marble-cake structure arising from remixing of subducted crust with the convecting mantle. During the Proterozoic and Phanerozoic, remixing of slabs has buffered the evolution of the depleted mantle to a rate of 2.2 ɛNd units Ga -1, with fractionation of Lu from Hf in the sediment component imparting the large range in 176Hf/ 177Hf relative to 143Nd/ 144Nd observed in MORB. Only the high ɛNd values of some Archean komatiites are compatible with derivation from unbuffered mantle. The existence of a very depleted reservoir is attributed to stabilisation of a large early continental crust through either obduction tectonics or slab melting regimes which reduced the efficiency of crustal recycling back into the mantle. Generation of komatiite is therefore a consequence of mantle composition, and is permitted in ocean ridge environments and/or under hydrous melting conditions. Correspondingly, as intraplate volcanism depends on survival of volatile-bearing sources, its appearance in the Middle Proterozoic corresponds to the time in the Earth's thermal evolution at which minerals such as phlogopite and amphibole could survive in off-ridge environments in the shallow asthenosphere. The geodynamic evolution of the Earth was thus determined at convergent margins, not by plumes and hotspots, with the decline in thermal regime causing both a reduction in size of crust and continental mantle roots, the latter becoming a source for intraplate volcanism while the crust was incorporated into the convecting mantle.

Gas emission strength and evolution of the molar ratio of BrO/SO2 in the plume of Nyiragongo in comparison to Etna

NASA Astrophysics Data System (ADS)

Bobrowski, N.; von Glasow, R.; Giuffrida, G. B.; Tedesco, D.; Aiuppa, A.; Yalire, M.; Arellano, S.; Johansson, M.; Galle, B.

2015-01-01

Airborne and ground-based differential optical absorption spectroscopy observations have been carried out at the volcano Nyiragongo (Democratic Republic of Congo) to measure SO2 and bromine monoxide (BrO) in the plume in March 2004 and June 2007, respectively. Additionally filter pack and multicomponent gas analyzer system (Multi-GAS) measurements were carried out in June 2007. Our measurements provide valuable information on the chemical composition of the volcanic plume emitted from the lava lake of Nyiragongo. The main interest of this study has been to investigate for the first time the bromine emission flux of Nyiragongo (a rift volcano) and the BrO formation in its volcanic plume. Measurement data and results from a numerical model of the evolution of BrO in Nyiragongo volcanic plume are compared with earlier studies of the volcanic plume of Etna (Italy). Even though the bromine flux from Nyiragongo (2.6 t/d) is slightly greater than that from Etna (1.9 t/d), the BrO/SO2 ratio (maximum 7 × 10-5) is smaller than in the plume of Etna (maximum 2.1 × 10-4). A one-dimensional photochemical model to investigate halogen chemistry in the volcanic plumes of Etna and Nyiragongo was initialized using data from Multi-GAS and filter pack measurements. Model runs showed that the differences in the composition of volcanic volatiles led to a smaller fraction of total bromine being present as BrO in the Nyiragongo plume and to a smaller BrO/SO2 ratio.

Measurements of Unexpected Ozone Loss in a Nighttime Space Shuttle Exhaust Plume: Implications for Geo-Engineering Projects

NASA Astrophysics Data System (ADS)

Avallone, L. M.; Kalnajs, L. E.; Toohey, D. W.; Ross, M. N.

2008-12-01

Measurements of ozone, carbon dioxide and particulate water were made in the nighttime exhaust plume of the Space Shuttle (STS-116) on 9 December 2006 as part of the PUMA/WAVE campaign (Plume Ultrafast Measurements Acquisition/WB-57F Ascent Video Experiment). The launch took place from Kennedy Space Center at 8:47 pm (local time) on a moonless night and the WB-57F aircraft penetrated the shuttle plume approximately 25 minutes after launch in the lowermost stratosphere. Ozone loss is not predicted to occur in a nighttime Space Shuttle plume since it has long been assumed that the main ozone loss mechanism associated with rocket emissions requires solar photolysis to drive several chlorine-based catalytic cycles. However, the nighttime in situ observations show an unexpected loss of ozone of approximately 250 ppb in the evolving exhaust plume, inconsistent with model predictions. We will present the observations of the shuttle exhaust plume composition and the results of photochemical models of the Space Shuttle plume. We will show that models constrained by known rocket emission kinetics, including afterburning, and reasonable plume dispersion rates, based on the CO2 observations, cannot explain the observed ozone loss. We will propose potential explanations for the lack of agreement between models and the observations, and will discuss the implications of these explanations for our understanding of the composition of rocket emissions. We will describe the potential consequences of the observed ozone loss for long-term damage to the stratospheric ozone layer should geo-engineering projects based on rocket launches be employed.

Retrieval of volcanic ash composition and particle size using high spatial resolution satellite data

NASA Astrophysics Data System (ADS)

Williams, D.; Ramsey, M. S.

2017-12-01

Volcanic ash plumes are a complex mixture of glass, mineral and lithic fragments in suspension with multiple gas species. These plumes are rapidly injected into the atmosphere, traveling thousands of kilometers from their source and affecting lives and property. One important use of satellite-based data has been to monitor volcanic plumes and their associated hazards. For distal plumes, the transmissive properties of volcanic ash in the thermal infrared (TIR) region allows the effective radii, composition, and density to be determined using approaches such as radiative transfer modelling. Proximal to the vent, however, the plume remains opaque, rendering this method invalid. We take a new approach to proximal plume analysis by assuming the plume's upper layer behaves spectrally as a solid surface in the TIR, due to the temperature and density of the plume soon after ejection from the vent. If this hypothesis is true, linear mixing models can be employed together with an accurate spectral library to compute both the particle size and petrology of every plume pixel. This method is being applied to high spatial resolution TIR data from the ASTER sensor using the newly developed ASTER Volcanic Ash Library (AVAL). AVAL serves as the spectral end-member suite from which to model plume data of 4 volcanoes: Chaitén, Puyehue-Cordón Caulle, Sakurajima and Soufrière Hills Volcano (SHV). Preliminary results indicate that this approach may be valid. The Sakurajima and SHV AVAL spectra provide an excellent fit to the ASTER data, whereas crushed high silica glass served as an appropriate end-member for both Chaitén and Puyehue-Cordón Caulle. In all cases, the best-fit size fractions are < 45 µm. Analysis of the proximal plume is essential in understanding the volcanic processes occurring within the vent. This study provides unprecedented detail of this region of the plume, further demonstrating the need for the continuation of high spatial resolution TIR satellite missions.

A 1.5 Ma record of plume-ridge interaction at the Western Galápagos Spreading Center (91°40‧-92°00‧W)

NASA Astrophysics Data System (ADS)

Herbrich, Antje; Hauff, Folkmar; Hoernle, Kaj; Werner, Reinhard; Garbe-Schönberg, Dieter; White, Scott

2016-07-01

Shallow (elevated) portions of mid-ocean ridges with enriched geochemical compositions near hotspots document the interaction of hot, geochemically-enriched plume mantle with shallow depleted upper mantle. Whereas the spatial variations in geochemical composition of ocean crust along the ridge axis in areas where plume-ridge interaction is taking place have been studied globally, only restricted information exists concerning temporal variations in geochemistry of ocean crust formed through plume-ridge interaction. Here we present a detailed geochemical study of 0-1.5 Ma ocean crust sampled from the Western Galápagos Spreading Center (WGSC) axis to 50 km north of the axis, an area that is presently experiencing a high influx of mantle material from the Galápagos hotspot. The tholeiitic to basaltic andesitic fresh glass and few bulk rock samples have incompatible element abundances and Sr-Nd-Pb isotopic compositions intermediate between depleted normal mid-ocean-ridge basalt (N-MORB) from >95.5°W along the WGSC and enriched lavas from the Galápagos Archipelago, displaying enriched (E-)MORB type compositions. Only limited and no systematic geochemical variations are observed with distance from the ridge axis for <1.0 Ma old WGSC crust, whereas 1.0-1.5 Ma old crust trends to more enriched isotopic compositions in 87Sr/86Sr, 143Nd/144Nd, 207Pb/204Pb and 208Pb/204Pb isotope ratios. On isotope correlation diagrams, the data set displays correlations between depleted MORB and two enriched components. Neither the geographically referenced geochemical domains of the Galápagos Archipelago nor the end members used for principal component analysis can successfully describe the observed mixing relations. Notably an off-axis volcanic cone at site DR63 has the appropriate composition to serve as the enriched component for the younger WGSC and could represent a portion of the northern part of the Galápagos plume not sampled south of the WGSC. Similar compositions to samples from volcanic cone DR63 have been found in the northern part of the 11-14 Ma Galápagos hotspot track offshore Costa Rica, indicating that this composition is derived from the northern portion of the Galápagos plume. The older WGSC requires involvement of an enriched mantle two (EMII) type source, not recognized thus far in the Galápagos system, and is interpreted to reflect entrained material either from small-scale heterogeneities within the upper mantle or from the mantle transition zone. Overall the source material for the 0-1.5 Ma WGSC ocean crust appears to represent mixing of depleted upper mantle with Northern Galápagos Plume material of relatively uniform composition in relatively constant proportions.

Three Dimensional Volcanic Plume Simulations on Early Mars

NASA Astrophysics Data System (ADS)

Fisher, M. A.; Kobs-Nawotniak, S. E.

2016-12-01

Current explosive volcanic plume models for early Mars are thought to overestimate plume height by tens of kilometers. They are based on 1D empirical terrestrial plume models, which determine plume rise using Morton-style convection. Not only do these models fail to account for turbulent mixing processes, but the Martian versions also violate assumptions regarding the speed of sound, radial expansion, and availability of ambient air for entrainment. Since volcanically derived volatiles are hypothesized to have increased early Martian warming, it is vital to understand how high these volatiles can be injected into the atmosphere. Active Tracer High-resolution Atmospheric Model (ATHAM; Oberhuber et al., 1998) is a 3D plume simulator that circumvents the underlying assumptions of the current Martian plume models by solving the Navier-Stokes equations. Martian-ATHAM (M-ATHAM) simulates Martian volcanic eruptions by replacing terrestrial planetary and atmospheric conditions with those appropriate for early Mars. In particular we evaluate three different atmospheric compositions with unique temperature and density profiles: 99.5% CO2/0.5% SO2 and 85% CO2/15% H2 representing a "warm and wet" climate and 100% CO2 representing a "cold and wet" climate. We evaluated for mass eruption rates from 10^3 kg/s to 10^10 kg/s using the Idaho National Laboratory's supercomputer Falcon in order determine what conditions produced stable eruption columns. Of the three different atmospheric compositions, 100% CO2 and 99.5% CO2/0.5% SO2 produced stable plumes for the same mass eruption rates whereas the 85% CO2/15% H2 atmosphere produced stable plumes for a slightly higher range of mass eruption rates. The tallest plumes were produced by 85% CO2/15% H2 atmosphere, producing plumes 5% taller than the revised empirical models, suggesting closer agreement than previously assumed under certain conditions. In comparison to terrestrial plumes, all early Martian plumes needed higher mass eruption rates to become positively buoyant, but could sustain stable plumes at higher mass eruption rates than terrestrial eruptions.

The Chemical Structure of the Hawaiian Mantle Plume

NASA Astrophysics Data System (ADS)

Ren, Z.; Hirano, N.; Hirata, T.; Takahashi, E.; Ingle, S.

2004-12-01

Numerous geochemical studies of Hawaiian basaltic lavas have shown that the Hawaiian mantle plume is isotopically heterogeneous. However, the distribution and scale of these heterogeneities remain unknown. This is essentially due to the complex interactions created by melting a heterogeneous source, subsequent aggregation of the melts on their way to the surface, and mixing that takes place in shallow magma chambers prior to eruption. In sum, the measured compositions of bulk lavas may represent only _eaverage_f compositions that do not fully reflect the complexity of either the mantle source heterogeneity and/or chemical structure. Melt inclusions, or samples of the local magma frozen in olivine phenocrysts during their formation, are better at recording the complex magmatic history than are the bulk samples. Here, we report major and trace element compositions of olivine-hosted melt inclusions from submarine Haleakala lavas that were collected by 2001-2002 JAMSTEC cruises measured by EPMA and LA-ICP-MS after homogenization at 1250° C, QFM for 20min. Melt inclusions from the submarine Hana Ridge (Haleakala volcano) show large ranges in CaO/Al2O3 (0.92-1.50), TiO2/Na2O (0.79-1.60) and Sr/Nb (14.56-36.60), Zr/Nb (6.48-16.95), ranging from Kilauea-like to Mauna Loa-like compositions within separately-sampled lavas as well as in a single host lava sample. Bulk rocks geochemistry shows that major element composition and trace element ratios such as Zr/Nb, Sr/Nb (Ren et al., 2004a, in press, J. Petrol.) together with Pb, Nd and Sr isotopic ratios (Ren et al., 2004b, submitted to J. Petrol.) of Haleakala shield volcano also display systematic compositional variation changing from a Kilauea-like in the submarine Hana Ridge (main shield stage) to Kilauea-Mauna Loa-like in the subaerial Honomanu stage (late shield stage, data from Chen and Frey, 1991). Some of the compositional variations in melt inclusions in single rocks are wider range than over-all variation observed in bulk rocks. It is important that both Kilauea-like and Mauna Loa-like compositions co-exist in melt inclusions in single submarine Hana Ridge rocks which are identified as Kilauea-like based on bulk geochemistry. These observations are inconsistent with the current interpretation that magma compositions are controlled by concentric zonation of the Hawaiian mantle plume (e.g. Kea component and Loa component), manifested as the Kea trend and the Loa trend volcanoes (e.g. Hauri, 1996; Lassiter et al., 1996). Our new data from olivine-hosted melt inclusions imply that the chemical structure of the Hawaiian mantle plume is significantly more complicated than previously modeled and the length-scale of chemical heterogeneity must be remarkably smaller than estimated based on bulk rock geochemistry.

Comparison of ACCENT 2000 Shuttle Plume Data with SIMPLE Model Predictions

NASA Astrophysics Data System (ADS)

Swaminathan, P. K.; Taylor, J. C.; Ross, M. N.; Zittel, P. F.; Lloyd, S. A.

2001-12-01

The JHU/APL Stratospheric IMpact of PLume Effluents (SIMPLE)model was employed to analyze the trace species in situ composition data collected during the ACCENT 2000 intercepts of the space shuttle Space Transportation Launch System (STS) rocket plume as a function of time and radial location within the cold plume. The SIMPLE model is initialized using predictions for species depositions calculated using an afterburning model based on standard TDK/SPP nozzle and SPF plume flowfield codes with an expanded chemical kinetic scheme. The time dependent ambient stratospheric chemistry is fully coupled to the plume species evolution whose transport is based on empirically derived diffusion. Model/data comparisons are encouraging through capturing observed local ozone recovery times as well as overall morphology of chlorine chemistry.

Volcanic Evolution in the Galapagos: The Geochemistry and Petrology of Espanola Island

NASA Astrophysics Data System (ADS)

McGuire, M.; Varga, K. C.; Harpp, K. S.; Geist, D.; Hall, M. L.

2015-12-01

The Galapagos Archipelago consists of a series of volcanic islands located ~1,000 km west of South America that are thought to be the result of a mantle plume. The southeasternmost island, Espanola, is one of the smallest of the major islands, measuring only 7 by 14 km and reaching an elevation of 200 m. Espanola is also the oldest island in the chain, with K-Ar dates from 3.01 ± 0.11 to 3.31 ± 0.36 million years (Hall et al. 1983; White et al., 1993). The southern coast is defined by cliffs that exceed 100 m in height, made up of nearly flat-lying lavas that are each several meters thick. The northern coastline consists of lavas that dip gently toward the ocean from the highlands, as well as remnants of eroded cinder cones. Paleomagnetic measurements made in the field indicate that the western half of the island is reversely polarized, whereas most lavas measured across the eastern half are normally polarized. Major element analyses of samples from across the island indicate that fractional crystallization is the dominant process controlling chemical variations in Espanola lavas, suggesting a relatively long-lived magmatic plumbing system. Stratigraphically constrained chemical variations suggest the magma chamber may have experienced periodic replenishment by compositionally homogeneous primitive melts. Variable fluid-mobile trace element concentrations provide some evidence for contributions from ancient, recycled oceanic crust to the parental melts. Espanola lavas have more depleted Sr and Pb radiogenic isotope ratios than either Floreana or Fernandina, and lie on a mixing curve between the composition of the plume and that of the depleted upper mantle. Between ~3 and 8 Ma, the Galapagos Spreading Center was closer to the Galapagos plume than it is today. Given that Espanola was constructed during the same period, the depleted isotopic signatures suggest that plume-ridge interaction may have been a strong influence on the island's geochemical composition.

Effect of defocusing on laser ablation plume observed by laser-induced fluorescence imaging spectroscopy

NASA Astrophysics Data System (ADS)

Oba, Masaki; Miyabe, Masabumi; Akaoka, Katsuaki; Wakaida, Ikuo

2016-02-01

We used laser-induced fluorescence imaging with a varying beam focal point to observe ablation plumes from metal and oxide samples of gadolinium. The plumes expand vertically when the focal point is far from the sample surface. In contrast, the plume becomes hemispherical when the focal point is on the sample surface. In addition, the internal plume structure and the composition of the ablated atomic and ionic particles also vary significantly. The fluorescence intensity of a plume from a metal sample is greater than that from an oxide sample, which suggests that the number of monatomic species produced in each plume differs. For both the metal and oxide samples, the most intense fluorescence from atomic (ionic) species is observed with the beam focal point at 3-4 mm (2 mm) from the sample surface.

In-situ and Remote-Sensing Data Fusion Using Machine Learning Techniques to Infer Urban and Fire Related Pollution Plumes

NASA Astrophysics Data System (ADS)

Segal-Rosenhaimer, M.; Russell, P. B.; Schmid, B.; Redemann, J.; Livingston, J. M.; Flynn, C. J.; Johnson, R. R.; Dunagan, S. E.; Shinozuka, Y.; Kacenelenbogen, M. S.; Chatfield, R. B.

2014-12-01

Airmass type characterization is key in understanding the relative contribution of various emission sources to atmospheric composition and air quality and can be useful in bottom-up model validation and emission inventories. However, classification of pollution plumes from space is often not trivial. Sub-orbital campaigns, such as SEAC4RS (Studies of Emissions, Atmospheric Composition, Clouds and Climate Coupling by Regional Surveys) give us a unique opportunity to study atmospheric composition in detail, by using a vast suite of in-situ instruments for the detection of trace gases and aerosols. These measurements allow identification of spatial and temporal atmospheric composition changes due to various pollution plumes resulting from urban, biogenic and smoke emissions. Nevertheless, to transfer the knowledge gathered from such campaigns into a global spatial and temporal context, there is a need to develop workflow that can be applicable to measurements from space. In this work we rely on sub-orbital in-situ and total column remote sensing measurements of various pollution plumes taken aboard the NASA DC-8 during 2013 SEAC4RS campaign, linking them through a neural-network (NN) algorithm to allow inference of pollution plume types by input of columnar aerosol and trace-gas measurements. In particular, we use the 4STAR (Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research) airborne measurements of wavelength dependent aerosol optical depth (AOD), particle size proxies, O3, NO2 and water vapor to classify different pollution plumes. Our method relies on assigning a-priori "ground-truth" labeling to the various plumes, which include urban pollution, different fire types (i.e. forest and agriculture) and fire stage (i.e. fresh and aged) using cluster analysis of aerosol and trace-gases in-situ and expert input and the training of a NN scheme to fit the best prediction parameters using 4STAR measurements as input. We explore our misclassification rates as related to our "ground-truth" labels, and with multi-layered pollution plume cases. The next step in our analysis is to optimize parameter selection for a scheme that can be applied to space-borne aerosol and trace-gas observation platforms such as OMI, and future geostationary satellites such as TEMPO and GEO-CAPE.

In-Situ and Remote-Sensing Data Fusion Using Machine Learning Techniques to Infer Urban and Fire Related Pollution Plumes

NASA Technical Reports Server (NTRS)

Russell, P. B.; Segal-Rozenhaimer, M.; Schmid, B.; Redemann, J.; Livingston, J. M.; Flynn, C.J.; Johnson, R. R.; Dunagan, S. E.; Shinozuka, Y.; Kacenelenbogen, M.;

Carbonatite and silicate melt metasomatism of the mantle surrounding the Hawaiian plume: Evidence from volatiles, trace elements, and radiogenic isotopes in rejuvenated-stage lavas from Niihau, Hawaii

NASA Astrophysics Data System (ADS)

Dixon, Jacqueline; Clague, David A.; Cousens, Brian; Monsalve, Maria Luisa; Uhl, Jessika

2008-09-01

We present new volatile, trace element, and radiogenic isotopic compositions for rejuvenated-stage lavas erupted on Niihau and its submarine northwest flank. Niihau rejuvenated-stage Kiekie Basalt lavas are mildly alkalic and are isotopically similar to, though shifted to higher 87Sr/86Sr and lower 206Pb/204Pb than, rejuvenated-stage lavas erupted on other islands and marginal seafloor settings. Kiekie lavas display trace element heterogeneity greater than that of other rejuvenated-stage lavas, with enrichments in Ba, Sr, and light-rare earth elements resulting in high and highly variable Ba/Th and Sr/Ce. The high Ba/Th lavas are among the least silica-undersaturated of the rejuvenated-stage suite, implying that the greatest enrichments are associated with the largest extents of melting. Kiekie lavas also have high and variable H2O/Ce and Cl/La, up to 620 and 39, respectively. We model the trace element concentrations of most rejuvenated-stage lavas by small degrees (˜1% to 9%) of melting of depleted peridotite recently metasomatized by a few percent of an enriched incipient melt (0.5% melting) of the Hawaiian plume. Kiekie lavas are best explained by 4% to 13% partial melting of a peridotite source metasomatized by up to 0.2% carbonatite, similar in composition to oceanic carbonatites from the Canary and Cape Verde Islands, with lower proportion of incipient melt than that for other rejuvenated-stage lavas. Primary H2O and Cl of the carbonatite component must be high, but variability in the volatile data may be caused by heterogeneity in the carbonatite composition and/or interaction with seawater. Our model is consistent with predictions based on carbonated eclogite and peridotite melting experiments in which (1) carbonated eclogite and peridotite within the Hawaiian plume are the first to melt during plume ascent; (2) carbonatite melt metasomatizes plume and surrounding depleted peridotite; (3) as the plume rises, silica-undersaturated silicate melts are also produced and contribute to the metasomatic signature. The metasomatic component is best preserved at the margins of the plume, where low extents of melting of the metasomatized depleted mantle surrounding the plume are sampled during flexural uplift. Formation of carbonatite melts may provide a mechanism to transfer plume He to the margins of the plume.

Plume versus plate origin for the Shatsky Rise oceanic plateau (NW Pacific): Insights from Nd, Pb and Hf isotopes

NASA Astrophysics Data System (ADS)

Heydolph, Ken; Murphy, David T.; Geldmacher, Jörg; Romanova, Irina V.; Greene, Andrew; Hoernle, Kaj; Weis, Dominique; Mahoney, John

2014-07-01

Shatsky Rise, an early Cretaceous igneous oceanic plateau in the NW Pacific, comprises characteristics that could be attributed to either formation by shallow, plate tectonic-controlled processes or to an origin by a mantle plume (head). The plateau was drilled during Integrated Ocean Drilling Program (IODP) Expedition 324. Complementary to a recent trace element study (Sano et al., 2012) this work presents Nd, Pb and Hf isotope data of recovered lava samples cored from the three major volcanic edifices of the Shatsky Rise. Whereas lavas from the oldest edifice yield fairly uniform compositions, a wider isotopic spread is found for lavas erupted on the younger parts of the plateau, suggesting that the Shatsky magma source became more heterogeneous with time. At least three isotopically distinct components can be identified in the magma source: 1) a volumetrically and spatially most common, moderately depleted component of similar composition to modern East Pacific Ridge basalt but with low 3He/4He, 2) an isotopically very depleted component which could represent local, early Cretaceous (entrained) depleted upper mantle, and 3) an isotopically enriched component, indicating the presence of (recycled) continental material in the magma source. The majority of analyzed Shatsky lavas, however, possess Nd-Hf-Pb isotope compositions consistent with a derivation from an early depleted, non-chondritic reservoir. By comparing these results with petrological and trace element data of mafic volcanic rock samples from all three massifs (Tamu, Ori, Shirshov), we discuss the origin of Shatsky Rise magmatism and evaluate the possible involvement of a mantle plume (head).

Petrologic evidence that most ocean islands derive from thermally driven mantle plumes

NASA Astrophysics Data System (ADS)

Putirka, K. D.

2006-12-01

Perhaps the most crucial test of the mantle plume hypothesis concerns whether hot spots are indeed hot. To conduct this test, olivine-liquid equilibria are used to estimate mantle potential temperatures (Tp) for 15 putative plume localities (using the GEOROC database). Ocean islands (OIB) were selected on the availability of rocks that attain olivine control (where olivine addition/removal alone controls rock composition) so that primitive FeO contents could be estimated. Several other variables in addition to FeO must also be known: Except at Iceland and Hawaii, where large numbers of olivine analyses allow individual estimates for the maximum forsterite contents (Fomax) of olivines, a single Fomax value, 91.5, is adopted for all OIB (and MORB; determined from a global database of olivine compositions); as a null hypothesis, MORB-like values for oxygen fugacity (QFM-1; Bezos and Humler, 2005) and the Fe-Mg exchange coefficient between olivine and liquid (0.31; calculated from Toplis, 2005, Herzberg and O'Hara, 1998) are adopted. Generalized differences in water contents between OIB and MORB (Dixon et al., 2002) are also accounted for. All temperatures are calculated at 1 GPa, using averages of existing (Beattie, 1993) and new (Putirka et al., 2006) olivine geothermometers. Except for Galapagos, primitive OIBs have nearly uniform FeO contents that are higher compared to MORB (at MgO>10 wt. %, mean OIB FeOt = 11.6 wt. %). These high FeO contents require higher mean temperatures of olivine-liquid equilibration for OIB, by an average of 150±20°C compared to MORB. Olivine equilibration temperatures do not depend on mantle source composition, so are independent of whether eclogite-type components occur in the mantle. If a peridotite bulk composition is assumed (to estimate melt fraction from partial melting experiments) olivine equilibration temperatures can be converted to Tp; OIB (Galapagos excepted) yield a mean Tp of 1583°C, compared to 1397°C for MORB. When inter- island compositional variation is accounted for, all OIB except Galapagos yield excess temperatures (Tp^{OIB} - Tp^{MORB}) of 133-280°C, with a mean of 186± 36°C. Galapagos lavas yield an excess temperature of 16°C; perhaps mixing has diluted its thermal signal, but in any event, its Tp is essentially identical to MORB. Nevertheless, most OIB (93% in this sample) exhibit large excess temperatures. Thermally driven mantle plumes, as proposed by Morgan (1971), thus appear to be common, not rare. A second implication, less certain than the first, involves the narrow standard deviation of ±36°C for Tp at OIB, which almost certainly reflects a lower limit to actual thermal variability. This narrow range indicates that all hot spots derive from a single thermal boundary layer.

Ion Formation Resulting from Freezing, Thawing, and Collisional Processes in Plumes Emitted from Planetary Bodies: Implications for Plume Chemistry and the Detection of Trace Organics Present in Enceladus Geysers

NASA Astrophysics Data System (ADS)

Beauchamp, J. L.; Wiley, J. S.; Thomas, D. A.

2014-12-01

Icy plumes emitted into space from Enceladus and other planetary bodies offer the intriguing possibility of sampling the composition of subsurface liquid reservoirs that may comprise habitable zones of particular astrobiological significance in our solar system. Mass spectrometric sampling of plume materials enables the detection of molecules that facilitate an assessment of the extent of chemical and biological evolution that may have occurred in a subsurface sea. In laboratory experiments we have investigated the physical and chemical processes that occur in the complex plume environment that lead to ionization of trace organic constituents, both as a result of the freezing of liquid droplets and the thawing of icy particles. We also demonstrate that collisions between icy particles lead to triboelectric charging. Subsequent discharges between oppositely charged particles result not only in the ionization of trace organics but to chemical reactions between molecular components present in the particles. For example, nitriles react with water to form amides and acids. In particular, icy particles doped with small amounts of aminoacetonitrile and water lead to the formation of the simplest amino acid glycine. The implications which these observations may have for sampling plume composition from orbit in a future mission to Enceladus will be discussed.

A Multifaceted Sampling Approach to Better Understanding Biogeochemical and Hydrogeological Controls on Uranium Mobility at a Former Uranium Mill Tailings Site in Riverton, Wyoming

NASA Astrophysics Data System (ADS)

Dam, W. L.; Johnson, R. H.; Campbell, S.; Bone, S. E.; Noel, V.; Bargar, J.

2015-12-01

Understanding uranium mobility in subsurface environments is not trivial. Obtaining sufficient data to accurately represent soil and aquifer characteristics can require unique approaches that evolve with added site knowledge. At Riverton, the primary source of uranium mill tailings remaining from ore processing was removed but contaminant plumes have persisted longer than predicted by groundwater modeling. What are the primary mechanisms controlling plume persistence? DOE is conducting new characterization studies to assist our understanding of underlying biogeochemical and hydrogeological mechanisms affecting secondary sources. A variety of field sampling techniques are being sequentially employed including augering, trenching, pore water sampling, and installing multi-level wells. In August 2012, vadose zone soil samples from 34 locations and groundwater from 103 boreholes were collected with Geoprobe ® direct push rods. Lower than expected uranium concentrations in composited shallow soils indicated the need for more focused and deeper samples. In May 2014, soil samples containing evaporites were collected along the bank of the Little Wind River; elevated uranium concentrations in evaporite minerals correlated with plume configurations and reflect contaminated groundwater discharge at the river. In September 2014, hand anger samples collected by the river and oxbow lake also indicated the presence of organic rich zones containing elevated uranium (>50 mg/kg). Subsequent samples collected from five backhoe trenches in May 2015 revealed a highly heterogeneous vadose zone composed of clay, silt, sand and cobbles containing evaporites and organic rich zones which may interact with groundwater plumes.Plans for August 2015 include sonic drilling to obtain continuous cores from the surface down to the base of the surficial aquifer with multi-level monitoring wells constructed in each borehole to assess vertical variation in groundwater chemistry. Temporary well-points will be installed adjacent to the river to assess geochemical and flow controls in the area of plume stagnation. Analyses include critical element speciation (C, S, Fe, and U), microbes, isotopes, diffusivity and flow characteristics. These activities support a dramatically improved understanding of plume persistence.

Orion Service Module Reaction Control System Plume Impingement Analysis Using PLIMP/RAMP2

NASA Technical Reports Server (NTRS)

Wang, Xiao-Yen J.; Gati, Frank; Yuko, James R.; Motil, Brian J.; Lumpkin, Forrest E.

2009-01-01

The Orion Crew Exploration Vehicle Service Module Reaction Control System engine plume impingement was computed using the plume impingement program (PLIMP). PLIMP uses the plume solution from RAMP2, which is the refined version of the reacting and multiphase program (RAMP) code. The heating rate and pressure (force and moment) on surfaces or components of the Service Module were computed. The RAMP2 solution of the flow field inside the engine and the plume was compared with those computed using GASP, a computational fluid dynamics code, showing reasonable agreement. The computed heating rate and pressure using PLIMP were compared with the Reaction Control System plume model (RPM) solution and the plume impingement dynamics (PIDYN) solution. RPM uses the GASP-based plume solution, whereas PIDYN uses the SCARF plume solution. Three sets of the heating rate and pressure solutions agree well. Further thermal analysis on the avionic ring of the Service Module showed that thermal protection is necessary because of significant heating from the plume.

Impingement effect of service module reaction control system engine plumes. Results of service module reaction control system plume model force field application to an inflight Skylab mission proximity operation situation with the inflight Skylab response

NASA Technical Reports Server (NTRS)

Lobb, J. D., Jr.

1978-01-01

Plume impingement effects of the service module reaction control system thruster firings were studied to determine if previous flight experience would support the current plume impingement model for the orbiter reaction control system engines. The orbiter reaction control system is used for rotational and translational maneuvers such as those required during rendezvous, braking, docking, and station keeping. Therefore, an understanding of the characteristics and effects of the plume force fields generated by the reaction control system thruster firings were examined to develop the procedures for orbiter/payload proximity operations.

Chemical composition of aerosol measurements in the air pollution plume during KORUS-AQ

NASA Astrophysics Data System (ADS)

Park, T.; Lee, J. B.; Lim, Y. J.; Ahn, J.; Park, J. S.; Soo, C. J.; Kim, J.; Park, S.; Lee, Y.; Desyaterik, Y.; Collett, J. L., Jr.; Lee, T.

2017-12-01

The Korean peninsula is a great place to study different sources of the aerosols: urban, rural and marine. In addition, Seoul is one of the large metropolitan areas in the world and has a variety of sources because half of the Korean population lives in Seoul, which comprises only 12% of the country's area. To understand the chemical composition of aerosol form long-range transport and local sources better, an Aerodyne High Resolution Time of Flight Aerosol Mass Spectrometer (HR-ToF-AMS) was deployed on an airborne platform (NASA DC-8 aircraft). The HR-ToF-AMS is capable of measuring non-refractory size resolved chemical composition of submicron particle(NR-PM1) in the air pollution plume, including mass concentration of organic carbon, nitrate, sulfate, and ammonium with 10 seconds time resolution. The measurements were performed twenty times research flight for understanding characteristic of the air pollution from May to June, 2016 on the South Korean peninsula during KORUS-AQ 2016 campaign. The scientific goal of this study is to characterize aerosol chemical properties and mass concentration in order to understand the role of the long-range transport from northeast Asia to South Korea, and influence of the local sources. To brief, organics dominated during all of flights. Also, organics and nitrate were dominant around energy industrial complex near by Taean, South Korea. The presentation will provide an overview of the composition of NR-PM1 measured in air pollution plumes, and deliver detail information about width, depth and spatial distribution of the pollutant in the air pollution plumes. The results of this study will provide high temporal and spatial resolved details on the air pollution plumes, which are valuable input parameters of aerosol properties for the current air quality models.

Quantitative Chemical Analysis of Enceladus' Plume Composition.

NASA Astrophysics Data System (ADS)

Peter, J.; Nordheim, T.; Hofmann, A.; Hand, K. P.

2017-12-01

Analyses of data from Cassini's Ion and Neutral Mass Spectrometer (INMS) taken during several close flybys of Enceladus suggest the presence of a potentially habitable ocean underneath the ice shell [1,2]. Proper identification of the molecular species sampled from Enceladus' plumes by INMS is of utmost importance for characterizing the ocean's chemical composition. Data from Cassini's Cosmic Dust Analyzer (CDA) and Visible and Infrared Mapping Spectrometer (VIMS) have provided clues for possible plume chemistry, but further analysis of the INMS data is necessary [3,4]. Here we present a novel automated algorithm for comparing INMS spectra and analogue laboratory spectra to a vast library of sample spectra provided by the National Institute of Standards and Technology (NIST). The algorithm implements a Monte Carlo simulation that computes the angular similarity between the spectrum of interest and a random sample of synthetic spectra generated at arbitrary mixing ratios of molecular species. The synthetic spectra with the highest similarity scores are then averaged to produce a convergent estimate of the mixing ratio of the spectrum of interest. Here we will discuss the application of this technique to INMS and laboratory data and the implication of our preliminary results for the ocean chemistry and habitability of Enceladus. 1. Waite, J., et al., 2009. Liquid Water on Enceladus From Observations of Ammonia and 40Ar in the Plume. Nature 460, 487-498. 2. Waite, J., et al. 2017. Cassini Finds Molecular Hydrogen in the Enceladus Plume: Evidence for Hydrothermal Processes. Science 356, 155-159. 3. Postberg, F., et al., 2008. The E Ring in the Vicinity of Enceladus II: Signatures of Enceladus in the Elemental Composition of E-Ring Particles. Icarus 193(2), 438-454. 4. Brown, R., et al., 2006. Composition and Physical Properties of Enceladus' Surface. Science 311, 1425-1428.

Mantle potential temperature estimates and primary melt compositions of the Low-Ti Emeishan flood basalt

NASA Astrophysics Data System (ADS)

Shellnutt, J. G.; Pham, Thuy T.

2018-05-01

The Late Permian Emeishan large igneous province (ELIP) is considered to be one of the best examples of a mantle plume derived large igneous province. One of the primary observations that favour a mantle plume regime is the presence of ultramafic volcanic rocks. The picrites suggest primary mantle melts erupted and that mantle potential temperatures (TP) of the ELIP were > 200oC above ambient mantle conditions. However, they may represent a mixture of liquid and cumulus olivine and pyroxene rather than primary liquids. Consequently, temperature estimates based on the picrite compositions may not be accurate. Here we calculate mantle potential temperature (TP) estimates and primary liquids compositions using PRIMELT3 for the low-Ti (Ti/Y < 500) Emeishan basalt as they represent definite liquid compositions. The calculated TP yield a range from 1400oC to 1550oC, which is consistent with variability across a mantle plume axis. The primary melt compositions of the basalts are mostly picritic. The results of this study indicate that the Emeishan basalt was produced by a high temperature regime and that a few of the ultramafic volcanic rocks may be indicative of primary liquids.

Late Mesozoic-Cenozoic intraplate magmatism in Central Asia and its relation with mantle diapirism: Evidence from the South Khangai volcanic region, Mongolia

NASA Astrophysics Data System (ADS)

Yarmolyuk, Vladimir V.; Kudryashova, Ekaterina A.; Kozlovsky, Alexander M.; Lebedev, Vladimir A.; Savatenkov, Valery M.

2015-11-01

The South Khangai volcanic region (SKVR) comprises fields of Late Mesozoic-Cenozoic volcanic rocks scattered over southern and central Mongolia. Evolution of the region from the Late Jurassic to the Late Cenozoic includes 13 successive igneous episodes that are more or less evenly distributed in time. Major patterns in the distribution of different-aged volcanic complexes were controlled by a systematic temporal migration of volcanic centers over the region. The total length of their trajectory exceeds 1600 km. Principle characteristics of local magmatism are determined. The composition of igneous rocks varies from basanites to rhyolites (predominantly, high-K rocks), with geochemistry close to that of OIB. The rock composition, however, underwent transformations in the Mesozoic-Cenozoic. Rejuvenation of mafic rocks is accompanied by decrease in the contents of HREE and increase of Nb and Ta. According to isotope data, the SKVR magmatic melts were derived from three isotope sources that differed in the Sr, Nd, and Pb isotopic compositions and successively alternated in time. In the Early Cretaceous, the predominant source composition was controlled by interaction of the EMII- and PREMA-type mantle materials. The PREMA-type mantle material dominated quantitatively in the Late Cretaceous and initial Early Cenozoic. From the latest Early Cenozoic to Late Cenozoic, the magma source also contained the EMI-type material along with the PREMA-type. The structural fabric, rock composition, major evolutionary pattern, and inner structure of SKVR generally comply with the criteria used to distinguish the mantle plume-related regions. Analogous features can be seen in other regions of recent volcanism in Central Asia (South Baikal, Udokan, Vitim, and Tok Stanovik). The structural autonomy of these regions suggests that distribution of the Late Mesozoic-Cenozoic volcanism in Central Asia was controlled by a group of relatively small hot finger-type mantle plumes associated with the common hot mantle field of Central Asia.

Tvashtar Montage

NASA Technical Reports Server (NTRS)

2007-01-01

The Tvashtar plume on Io, seen by the Hubble Space Telescope (HST) and by New Horizons.

(A): The image in which the plume was discovered, taken by HST in ultraviolet light on Feb. 14, 2007, at a wavelength of 260 nm. The red diamond indicates location of the Tvashtar hot spot seen later by New Horizons. (B): An HST image of Io and the Tvashtar plume seen against Jupiter; sulfur gas in the plume absorbs ultraviolet light, making the plume look reddish in this color composite. The composite is composed of images taken at 260 nm (blue), 330 nm (green), and 410 nm (red). Other images in this montage are in visible light from the Long-Range Reconnaissance Imager (LORRI). The scale bar is 200 kilometers long and the yellow star indicates the projected location of the hot spot at the Tvashtar plume source. The dashed line is the terminator, the line dividing day from night on Io. (C): The highest-resolution view of the full plume, at a resolution of 12.4 kilometers (7.7 miles) per pixel and a solar phase angle of 102 degrees, showing the complex filamentary structure of the plume. The images are sharpened by un-sharp masking; the dark line at the edge of the disk is an artifact of this sharpening. (D): An image at 145-degree phase angle at 22.4 kilometers (13.8 miles) per pixel, showing the time variability of the details of the plume structure and its persistent bright top. (F-J): Sequence of frames at 2-minute intervals showing dynamics in the upper part of the plume (the source is on the far side of Io). Colored diamonds track individual features whose speeds, projected on the plane of the sky, are shown in (E).

This image appears in the Oct. 12, 2007, issue of Science magazine, in a paper by John Spencer, et al.

Parameters of thermochemical plumes responsible for the formation of batholiths: Results of experimental simulation

NASA Astrophysics Data System (ADS)

Kirdyashkin, A. A.; Kirdyashkin, A. G.; Gurov, V. V.

2017-07-01

Based on laboratory and theoretical modeling results, we present the thermal and hydrodynamical structure of the plume conduit during plume ascent and eruption on the Earth's surface. The modeling results show that a mushroom-shaped plume head forms after melt eruption on the surface for 1.9 < Ka < 10. Such plumes can be responsible for the formation of large intrusive bodies, including batholiths. The results of laboratory modeling of plumes with mushroom-shaped heads are presented for Ka = 8.7 for a constant viscosity and uniform melt composition. Images of flow patterns are obtained, as well as flow velocity profiles in the melt of the conduit and the head of the model plume. Based on the laboratory modeling data, we present a scheme of a thermochemical plume with a mushroom-shaped head responsible for the formation of a large intrusive body (batholith). After plume eruption to the surface, melting occurs along the base of the massif above the plume head, resulting in a mushroom-shaped plume head. A possible mechanism for the formation of localized surface manifestations of batholiths is presented. The parameters of some plumes with mushroom-shaped heads (plumes of the Altay-Sayan and Barguzin-Vitim large-igneous provinces, and Khangai and Khentei plumes) are estimated using geological data, including age intervals and volumes of magma melts.

Photogrammetric and photometric investigation of a smoke plume viewed from space.

NASA Technical Reports Server (NTRS)

Randerson, D.; Garcia, J. G.; Whitehead, V. S.

1971-01-01

Use of detailed analyses of an Apollo 6 stereographic photograph of a smoke plume which originated in southern Arizona and crossed over into Mexico to illustrate how high-resolution photography can aid meteorologists in evaluating specific air pollution events. Photogrammetric analysis of the visible smoke plume revealed that the plume was 8.06 miles long and attained a maximum width of 4000 ft, 3.0 miles from the 570-ft chimney emitting the effluent. Stereometric analysis showed that the visible top of the plume rose nearly 2400 ft above stack top, attaining 90% of this total rise 1.75 miles downwind from the source. Photometric analysis of the plume revealed a field of plume optical density that portrayed leptokurtic and bimodal distributions rather than a true Gaussian distribution. A horizontal eddy diffusivity of about 650,000 sq cm/sec and a vertical eddy diffusivity of 230,000 sq cm/sec were determined from the plume dimensions. Neutron activation analysis of plume samples revealed the elemental composition of the smoke to be copper, arsenic, selenium, indium and antimony, with trace amounts of vanadium and scandium.

Orion Service Module Reaction Control System Plume Impingement Analysis Using PLIMP/RAMP2

NASA Technical Reports Server (NTRS)

Wang, Xiao-Yen; Lumpkin, Forrest E., III; Gati, Frank; Yuko, James R.; Motil, Brian J.

2009-01-01

The Orion Crew Exploration Vehicle Service Module Reaction Control System engine plume impingement was computed using the plume impingement program (PLIMP). PLIMP uses the plume solution from RAMP2, which is the refined version of the reacting and multiphase program (RAMP) code. The heating rate and pressure (force and moment) on surfaces or components of the Service Module were computed. The RAMP2 solution of the flow field inside the engine and the plume was compared with those computed using GASP, a computational fluid dynamics code, showing reasonable agreement. The computed heating rate and pressure using PLIMP were compared with the Reaction Control System plume model (RPM) solution and the plume impingement dynamics (PIDYN) solution. RPM uses the GASP-based plume solution, whereas PIDYN uses the SCARF plume solution. Three sets of the heating rate and pressure solutions agree well. Further thermal analysis on the avionic ring of the Service Module was performed using MSC Patran/Pthermal. The obtained temperature results showed that thermal protection is necessary because of significant heating from the plume.

Transport and recirculation of aerosols off Southern Africa—macroscale plume structure

NASA Astrophysics Data System (ADS)

Tyson, P. D.; D'Abreton, P. C.

A pall of aerosols and trace gases frequently occurs over southern Africa to a depth of ˜500 hPa, blanketing vast areas, particularly in the austral winter and spring. Large-scale offshore transport of these aerosols and trace gases in extremely large plumes from interior continental areas of the subcontinent to the Indian and Atlantic Oceans is a common occurrence. The nature of the transport plumes, their climatology, chemical composition and morphology are discussed. In the vertically integrated, surface-to-500 hPa layer, poleward of about 15° S, transport into the Indian Ocean is shown to be about 60% greater into the Indian Ocean than into the Atlantic Ocean. Recirculation of atmospheric constituents is considered and estimates of aerosol mass fluxes over central southern Africa are presented. Of the total of about 50 Mt yr -1 of aerosols being transported at the central meridian, 44% is shown to be recirculated material. The rest exits the subcontinent directly without recirculation. Preferred plume corridors of exit and entry are postulated for different localities on the east and west coasts. Two case studies of east- and west-coast plumes apparently flowing uniformly out of southern Africa are examined. The illusion of uniformity in plume structure is shown to be misleading. Both plumes are shown to be above and separated from the marine boundary layer. Each is over 1500 km in width and 3-5 km deep. Likewise, both are capped by absolutely stable layers at ˜500 hPa and exhibit a complex structure of both outflowing aerosols and trace gases and inflowing, recycled and recirculated material. Indications of the composition of the recirculated material are given and implications of the plume transports are considered.

Effects of NOx control and plume mixing on nighttime chemical processing of plumes from coal-fired power plants

NASA Astrophysics Data System (ADS)

Brown, Steven S.; Dubé, William P.; Karamchandani, Prakash; Yarwood, Greg; Peischl, Jeff; Ryerson, Thomas B.; Neuman, J. Andrew; Nowak, John B.; Holloway, John S.; Washenfelder, Rebecca A.; Brock, Charles A.; Frost, Gregory J.; Trainer, Michael; Parrish, David D.; Fehsenfeld, Frederick C.; Ravishankara, A. R.

2012-04-01

Coal-fired electric power plants produce a large fraction of total U.S. NOx emissions, but NOx from this sector has been declining in the last decade owing to installation of control technology. Nighttime aircraft intercepts of plumes from two different Texas power plants (Oklaunion near Wichita Falls and W. A. Parish near Houston) with different control technologies demonstrate the effect of these reductions on nighttime NOxoxidation rates. The analysis shows that the spatial extent of nighttime-emitted plumes to be quite limited and that mixing of highly concentrated plume NOx with ambient ozone is a determining factor for its nighttime oxidation. The plume from the uncontrolled plant had full titration of ozone through 74 km/2.4 h of downwind transport that suppressed nighttime oxidation of NO2 to higher oxides of nitrogen across the majority of the plume. The plume from the controlled plant did not have sufficient NOx to titrate background ozone, which led to rapid nighttime oxidation of NO2 during downwind transport. A plume model that includes horizontal mixing and nighttime chemistry reproduces the observed structures of the nitrogen species in the plumes from the two plants. The model shows that NOx controls not only reduce the emissions directly but also lead to an additional overnight NOx loss of 36-44% on average. The maximum reduction for 12 h of transport in darkness was 73%. The results imply that power plant NOxemissions controls may produce a larger than linear reduction in next-day, downwind ozone production following nighttime transport.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Groenen, Rik; Smit, Jasper; Orsel, Kasper

The oxidation of species in the plasma plume during pulsed laser deposition controls both the stoichiometry as well as the growth kinetics of the deposited SrTiO{sub 3} thin films, instead of the commonly assumed mass distribution in the plasma plume and the kinetic energy of the arriving species. It was observed by X-ray diffraction that SrTiO{sub 3} stoichiometry depends on the composition of the background gas during deposition, where in a relative small pressure range between 10{sup −2} mbars and 10{sup −1} mbars oxygen partial pressure, the resulting film becomes fully stoichiometric. Furthermore, upon increasing the oxygen (partial) pressure, themore » growth mode changes from 3D island growth to a 2D layer-by-layer growth mode as observed by reflection high energy electron diffraction.« less

Soil pore-gas sampling by photoacoustic radiometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sollid, J.E.

1994-11-01

Concentrations of volatile organics in a soil pore-gas plume were measured using a commercially available multigas monitor. The monitor is a photoacoustic radiometer (PAR) controlled by an on-board, programmable microprocessor. The measurements determine the extent and location of the vapor plume in the subsurface. At least twelve wells surrounding the sources are measured quarterly. The sources are located in former liquid chemical waste disposal pits and shafts at Los Alamos National Laboratory. The primary constituents of the plume are 1,1,1 trichloroethane (TCA), trichloroethene (TCE), and tetrachloroethene or perchloroethene or perchloroethene (PCE). Four quarters of data are presented for TCA. Allmore » were used primarily as solvents and degreasers. Previously the composition of the vapor plume was determined by Gas Chromatography Mass Spectrometer GCMS methods. Photoacoustic radiometry and gas chromatography are discussed giving the advantages and disadvantages of each method, although in this program they are basically complementary. Gas chromatography is a more qualitative method to determine which analytes are present and the approximate concentration. Photoacoustic radiometry, to function well, requires foreknowledge of constituents and serves best to determine how much is present. Measurements are quicker and more direct with photoacoustic methods. Once the constituents to be measured are known, the cost to monitor is much less using photoacoustics, and the results are available more quickly.« less

Evidence from Xenon isotopes for limited mixing between MORB sources and plume sources since 4.45 Ga

NASA Astrophysics Data System (ADS)

Mukhopadhyay, S.

2011-12-01

Xenon isotopes provide unique insights into the sources of volatile material for planet Earth, the degassing of the mantle, and the chemical evolution of the mantle [1-4]. 129Xe is produced from 129I, which has a half-life of 16 Myrs, and 131-136Xe are produced from 244Pu, which has a half-life of 80 Myrs. To a smaller extent, 131-136Xe are also produced from 238U fission. Thus, ratios of Pu-derived to U-derived fission xenon and 129I-derived to Pu-derived fission xenon constrain the rate and degree of outgassing of a mantle reservoir. Here, I report on the Pu-derived to U-derived fission xenon and Pu/I ratio of the Iceland plume. I then compare the plume observations with the gas rich popping rock from the North Mid Atlantic Ridge that samples the upper mantle [4]. Through step crushing of multiple aliquots of a basalt glass from Iceland, 51 high-precision He, Ne, Ar, and Xe isotopic compositions were generated. Combined He, Ne, and Xe measurements provide unequivocal evidence that the Iceland plume has a lower 129Xe/130Xe ratio than MORBs because it evolved with a I/Xe ratio distinct from the MORB source and not because of recycled atmosphere (which has low 129Xe/130Xe) in the plume source. Since 129I became extinct 80 Myrs after solar system formation, limited mixing between plume and MORB source is a stringent requirement since 4.45 Ga. Of the 51 different isotopic analyses, 42 data points were distinct from the atmospheric 129Xe/130Xe composition at two standard deviations. These 42 data points were utilized to calculate the ratio of Pu- to U-derived fission xenon. The starting composition of terrestrial Xe is a matter of debate. However, for reasonable starting compositions of air, non-radiogenic atmosphere, solar wind, and U-Xe [5-7], the Iceland plume ,on average, has approximately a factor of two higher Pu-derived xenon than the MORB source. These data thus, provide unequivocal evidence that the Iceland plume is less degassed than the MORB source and that the differences must have existed early on because Pu becomes extinct after ~ 400 Myrs. Thus, the Xe isotopic data suggests that differences between plume and MORB sources are the result of different mantle processing rates and not related to the preferential recycling of atmospheric gases into the plume source. Furthermore, if the plumes are derived from the large low shear wave velocity (LLSVPs) provinces at the base of the lower mantle [8], then our results require that LLSVPs are not made of solely recycled material. Rather, primitive material must constitute some fraction of the LLSVPs, and LLSVPs are ancient, having persisted through most of Earth's history. [1] Holland and Ballentine, Nature, 2006. [2] Yokochi and Marty, EPSL, 2004. [3] Coltice et al., Chem Geol., 2009. [4] Moriera et al., Science, 1998. [5] Caffee et al., Science, 1998. [6] Kunz et al., Science 1998. [7] Pepin and Porcelli, EPSL, 2006. [8] Torsvik et al., Nature, 2010.

Fossil plume head beneath the Arabian lithosphere?

NASA Astrophysics Data System (ADS)

Stein, Mordechai; Hofmann, Albrecht W.

1992-12-01

Phanerozoic alkali basalts from Israel, which have erupted over the past 200 Ma, have isotopic compositions similar to PREMA ("prevalent mantle") with narrow ranges of initial ɛ Nd(T) = +3.9-+5.9; 87Sr/ 86Sr(T)= 0.70292-0.70334; 206Pb/ 204Pb(T)= 18.88-19.99; 207Pb/ 204Pb(T)= 15.58-15.70; and 208Pb/ 204Pb(T)= 38.42-39.57. Their Nb/U(43 ± 9) and Ce/Pb(26 ± 6) ratios are identical to those of normal oceanic basalts, demonstrating that the basalts are essentially free of crustal contamination. Overall, the basalts are chemically and isotopically indistinguishable from many ordinary plume basalts, but no plume track can be identified. We propose that these and other, similar, magmas from the Arabian plate originated from a "fossilized" head of a mantle plume, which was unable to penetrate the continental lithosphere and was therefore trapped and stored beneath it. The plume head was emplaced some time between the late Proterozoic crust formation and the initiation of the Phanerozoic magmatic cycles. Basalts from rift environments in other continental localities show similar geochemistry to that of the Arabian basalts and their sources may also represent fossil plume heads trapped below the continents. We suggest that plume heads are, in general, characterized by the PREMA isotopic mantle signature, because the original plume sources (which may have HIMU or EM-type composition) have been diluted by overlying mantle material, which has been entrained by the plume heads during ascent. On the Arabian plate, rifting and thinning of the lithosphere caused partial melting of the stored plume, which led to periodic volcanism. In the late Cenozoic, the lithosphere broke up and the Red Sea opened. N-MORB tholeiites are now erupting in the central trough of the Red Sea, where the lithosphere has moved apart and the fossil plume has been exhausted, whereas E-MORBs are erupting in the northern and southern troughs, still tapping the plume reservoir. Fossil plumes, which are temporarily trapped at the base of the lithosphere, may explain why the uppermost mantle normally appears enriched when it is sampled by continental rift zones but depleted when it is sampled by MORB.

Mantle plumes in the vicinity of subduction zones

NASA Astrophysics Data System (ADS)

Mériaux, C. A.; Mériaux, A.-S.; Schellart, W. P.; Duarte, J. C.; Duarte, S. S.; Chen, Z.

2016-11-01

We present three-dimensional deep-mantle laboratory models of a compositional plume within the vicinity of a buoyancy-driven subducting plate with a fixed trailing edge. We modelled front plumes (in the mantle wedge), rear plumes (beneath the subducting plate) and side plumes with slab/plume systems of buoyancy flux ratio spanning a range from 2 to 100 that overlaps the ratios in nature of 0.2-100. This study shows that 1) rising side and front plumes can be dragged over thousands of kilometres into the mantle wedge, 2) flattening of rear plumes in the trench-normal direction can be initiated 700 km away from the trench, and a plume material layer of lesser density and viscosity can ultimately almost entirely underlay a retreating slab after slab/plume impact, 3) while side and rear plumes are not tilted until they reach ∼600 km depth, front plumes can be tilted at increasing depths as their plume buoyancy is lessened, and rise at a slower rate when subjected to a slab-induced downwelling, 4) rear plumes whose buoyancy flux is close to that of a slab, can retard subduction until the slab is 600 km long, and 5) slab-plume interaction can lead to a diversity of spatial plume material distributions into the mantle wedge. We discuss natural slab/plume systems of the Cascadia/Bowie-Cobb, and Nazca/San Felix-Juan Fernandez systems on the basis of our experiments and each geodynamic context and assess the influence of slab downwelling at depths for the starting plumes of Java, Coral Sea and East Solomon. Overall, this study shows how slab/plume interactions can result in a variety of geological, geophysical and geochemical signatures.

Dynamic melting in plume heads: the formation of Gorgona komatiites and basalts

NASA Astrophysics Data System (ADS)

Arndt, Nicholas T.; Kerr, Andrew C.; Tarney, John

1997-01-01

The small Pacific island of Gorgona, off the coast of Colombia, is well known for its spectacular spinifex-textured komatiites. These high-Mg liquids, which have been linked to a late Cretaceous deep mantle plume, are part of a volcanic series with a wide range of trace-element compositions, from moderately enriched basalts ( La/SmN ˜ 1.5) to extremely depleted ultramafic tuffs and picrites ( La/SmN ˜ 0.2). Neither fractional crystallization, nor partial melting of a homogeneous mantle source, can account for this large variation: the source must have been chemically heterogeneous. Low 143Nd/144Nd in the more enriched basalts indicates some initial source heterogeneity but most of the variation in magma compositions is believed to result from dynamic melting during the ascent of a plume. Modelling of major- and trace-element compositions suggests that ultramafic magmas formed at ˜ 60-100 km depth, and that the melt extraction that gave rise to their depleted sources started at still greater depths. The ultra-depleted lavas represent magmas derived directly from the hottest, most depleted parts of the plume; the more abundant moderately depleted basalts are interpreted as the products of pooling of liquids from throughout the melting region.

Controls on Plume Spacing and Plume Population in 3-D High Rayleigh Number Thermal Convection

NASA Astrophysics Data System (ADS)

Zhong, S.

2004-12-01

Dynamics of mantle plumes are important for understanding intra-plate volcanism and heat transfer in the mantle. Using 3D numerical models and scaling analyses, we investigated the controls of convective vigor or Ra on the dynamics of thermal plumes in isoviscous and basal heating thermal convection. We examined Ra-dependence of plume population, plume spacing, plume vertical velocity, and plume radius. We found that plume population does not increase with Ra monotonically. At relatively small Ra (<106), plume population is insensitive to Ra. For 3x106

Phase equilibrium constraints on the origin of basalts, picrites, and komatiites

NASA Astrophysics Data System (ADS)

Herzberg, C.; O'Hara, M. J.

1998-07-01

Experimental phase equilibrium studies at pressures ranging from 1 atm to 10 GPa are sufficient to constrain the origin of igneous rocks formed along oceanic ridges and in hotspots. The major element geochemistry of MORB is dominated by partial crystallization at low pressures in the oceanic crust and uppermost mantle, forcing compliance with liquid compositions in low-pressure cotectic equilibrium with olivine, plagioclase and often augite too; parental magmas to MORB formed by partial melting, mixing, and pooling have not survived these effects. Similarly, picrites and komatiites can transform to basalts by partial crystallization in the crust and lithosphere. However, parental picrites and komatiites that were successful in erupting to the surface typically have compositions that can be matched to experimentally-observed anhydrous primary magmas in equilibrium with harzburgite [L+Ol+Opx] at 3.0 to 4.5 GPa. This pressure is likely to represent an average for pooled magmas that collected at the top of a plume head as it flattened below the lithosphere. There is substantial uniformity in the normative olivine content of primary magmas at all depths in a plume melt column, and this results in pooled komatiitic magmas that are equally uniform in normative olivine. However, the imposition of pressure above 3 GPa produces picrites and komatiites with variations in normative enstatite and Al 2O 3 that reveal plume potential temperature and depths of initial melting. Hotter plumes begin to melt deeper than cooler plumes, yielding picrites and komatiites that are enriched in normative enstatite and depleted in Al 2O 3 because of a deeper column within which orthopyroxene can dissolve during decompression. Pressures of initial melting span the 4 to 10 GPa range, increasing in the following order: Iceland, Hawaii, Gorgona, Belingwe, Barberton. Parental komatiites and picrites from a single plume also exhibit internal variability in normative enstatite and Al 2O 3, indicating either a poorly mixed partial melt aggregation process in the plume or the imposition of partial crystallization of olivine-orthopyroxenite on a well-mixed parental magma. Plume shape and thermal structure can also influence the petrology and geochemistry of picrites and komatiites. Liquids extracted from harzburgite residues [L+Ol+Opx] will dominate magmatism in a plume head, and can erupt to form komatiites in oceanic plateaus. Liquids extracted from garnet peridotite residues in a plume axis will gain in importance when the plume head partially solidifies and is removed from the hotspot by a moving lithosphere, as is the case for Hawaii. The paradoxical involvement of garnet indicated by the heavy rare earth elements in picrites that otherwise have a harzburgite signature in Hawaii can be explained by the mixing and collection of magmas from the plume axis. Volcanic rocks from Hawaii and Gorgona and xenoliths from cratonic mantle provide evidence for the importance of partial crystallization of plume magmas when they encounter a cold lithosphere. Harzburgite residua and olivine-orthopyroxene cumulates formed in plumes can yield compositionally distinct lithospheric mantle which is buoyant, and this could have provided an important foundation for the stabilization of the first continents.

Methane Distribution In Plumes Of The South Mariana Back-arc Spreading Center

NASA Astrophysics Data System (ADS)

Toki, T.; Hirota, A.; Tsunogai, U.; Gamo, T.; Nakamura, K.; Noguchi, T.; Taira, N.; Oomori, T.; Ishibashi, J.; Utsumi, M.

2004-12-01

In the South Mariana Back-arc Spreading Center, two methane plumes were observed in water column based on analysis of methane in seawater samples collected during the R/V Thompson expeditions in 2003 around water depth of 2,700 m over the Fryer site on the ridge-axis seamount (12\\deg57.22N, 143\\deg37.16E, depth: 2,850 m). The estimated end-member isotopic compositions of methane in the two plumes are \\delta13C_{CH4} = -5‰ PDB and -50‰ PDB. These values indicated that the two plumes were originated from the different sources. During YK03-09 cruise using the submersible Shinkai 6500 from October to November in 2003, detailed seafloor observation discovered sulfide chimneys emitting black and clear hydrothermal fluid on the off-axis seamount at Pika site (12°55.15N, 143°36.96E, depth: 2,773 m). The result of analysis of isotopic composition of methane in the hydrothermal fluids recovered from the off-axis hydrothermal vents using WHATS (Water and Hydrothermal Atsuryoku Tight Sampler) was averaged value of -4‰ PDB (standard deviation = 1‰ PDB, n = 3). Hydrothermal fluids from the Fryer site were also sampled and were measured: average value = -6.7‰ PDB, standard deviation = 0.3‰ PDB, n = 3. During the R/V Thompson expeditions in March 2004 using ROV ROPOS, 11 ROPOS dives and CTD-RMS plume surveys were conducted, and newly discovered a huge hydrothermal structure with active fluid venting at Achaean site on the ridge skirt (12°56.37N, 143°37.92E, depth: 2,990 m). The δ ^{13}C_{CH4} value of the fluid sample from the site using ROCS (Rotary Clean Seawater sampler) was -14.7‰ PDB. Analysis of isotopic composition of methane in the plume samples collected using the CTD-hydrocast at water depth of 2,500 m over the Archaean site showed -45‰ PDB. Source of methane (δ ^{13}C_{CH4} = -50‰ PDB), however, in the two plumes of the South Mariana Back-arc Spreading Center has been missing. The δ ^{13}C of methane cannot be considered in sediment-starved seafloor hydrothermal fluids as the results from an abiogenic reaction in magma. Alternative explanation would be the secondary stimulated plume of methane that is formed in invertebrate guts of zooplankton swarmed about microbes in the plume, as proposed about a subsurface CH_{4} maximum in the upper oceanic water column. The secondary methane plume may be associated with methane plume without a corresponding enrichment in ^{3}He, observed in the Mariana Trough Back-arc basin at 14° N.

The role of wellbore remediation on the evolution of groundwater quality from CO₂ and brine leakage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mansoor, Kayyum; Carroll, Susan A.; Sun, Yunwei

Long-term storage of CO₂ in underground reservoirs requires a careful assessment to evaluate risk to groundwater sources. The focus of this study is to assess time-frames required to restore water quality to pre-injection levels based on output from complex reactive transport simulations that exhibit plume retraction within a 200-year simulation period. We examined the relationship between plume volume, cumulative injected CO₂ mass, and permeability. The role of mitigation was assessed by projecting falloffs in plume volumes from their maximum peak levels with a Gaussian function to estimate plume recovery times to reach post-injection groundwater compositions. The results show a strongmore » correlation between cumulative injected CO₂ mass and maximum plume pH volumes and a positive correlation between CO₂ flux, cumulative injected CO₂, and plume recovery times, with secondary dependence on permeability.« less

The role of wellbore remediation on the evolution of groundwater quality from CO₂ and brine leakage

DOE PAGES

Mansoor, Kayyum; Carroll, Susan A.; Sun, Yunwei

2014-12-31

Long-term storage of CO₂ in underground reservoirs requires a careful assessment to evaluate risk to groundwater sources. The focus of this study is to assess time-frames required to restore water quality to pre-injection levels based on output from complex reactive transport simulations that exhibit plume retraction within a 200-year simulation period. We examined the relationship between plume volume, cumulative injected CO₂ mass, and permeability. The role of mitigation was assessed by projecting falloffs in plume volumes from their maximum peak levels with a Gaussian function to estimate plume recovery times to reach post-injection groundwater compositions. The results show a strongmore » correlation between cumulative injected CO₂ mass and maximum plume pH volumes and a positive correlation between CO₂ flux, cumulative injected CO₂, and plume recovery times, with secondary dependence on permeability.« less

Evaluation of pressure in a plasma produced by laser ablation of steel

NASA Astrophysics Data System (ADS)

Hermann, Jörg; Axente, Emanuel; Craciun, Valentin; Taleb, Aya; Pelascini, Frédéric

2018-05-01

We investigated the time evolution of pressure in the plume generated by laser ablation with ultraviolet nanosecond laser pulses in a near-atmospheric argon atmosphere. These conditions were previously identified to produce a plasma of properties that facilitate accurate spectroscopic diagnostics. Using steel as sample material, the present investigations benefit from the large number of reliable spectroscopic data available for iron. Recording time-resolved emission spectra with an echelle spectrometer, we were able to perform accurate measurements of electron density and temperature over a time interval from 200 ns to 12 μs. Assuming local thermodynamic equilibrium, we computed the plasma composition within the ablated vapor material and the corresponding kinetic pressure. The time evolution of plume pressure is shown to reach a minimum value below the pressure of the background gas. This indicates that the process of vapor-gas interdiffusion has a negligible influence on the plume expansion dynamics in the considered timescale. Moreover, the results promote the plasma pressure as a control parameter in calibration-free laser-induced breakdown spectroscopy.

Io volcanism seen by new horizons: a major eruption of the Tvashtar volcano.

PubMed

Spencer, J R; Stern, S A; Cheng, A F; Weaver, H A; Reuter, D C; Retherford, K; Lunsford, A; Moore, J M; Abramov, O; Lopes, R M C; Perry, J E; Kamp, L; Showalter, M; Jessup, K L; Marchis, F; Schenk, P M; Dumas, C

2007-10-12

Jupiter's moon Io is known to host active volcanoes. In February and March 2007, the New Horizons spacecraft obtained a global snapshot of Io's volcanism. A 350-kilometer-high volcanic plume was seen to emanate from the Tvashtar volcano (62 degrees N, 122 degrees W), and its motion was observed. The plume's morphology and dynamics support nonballistic models of large Io plumes and also suggest that most visible plume particles condensed within the plume rather than being ejected from the source. In images taken in Jupiter eclipse, nonthermal visible-wavelength emission was seen from individual volcanoes near Io's sub-Jupiter and anti-Jupiter points. Near-infrared emission from the brightest volcanoes indicates minimum magma temperatures in the 1150- to 1335-kelvin range, consistent with basaltic composition.

Enceladus plume density from Cassini spacecraft attitude control data

NASA Astrophysics Data System (ADS)

Lorenz, Ralph D.; Burk, Thomas A.

2018-01-01

The plumes of Enceladus are of interest both as a geophysical phenomenon, and as an astrobiological opportunity for sampling internal material. Here we report measurements of the total mass density (gas plus dust, a combination not reported before except in the engineering literature) deduced from telemetry of Cassini's Attitude and Articulation Control System (AACS), as the spacecraft's thrusters or reaction wheels worked to maintain the desired attitude in the presence of drag torques during close flybys. The drag torque shows good agreement with the water vapor density measured by other instruments during the E5 encounter, but indicates a rather higher mass density on other passes (E3, E14), possibly indicating variations in gas composition and/or gas:dust ratio. The spacecraft appears to have intercepted about 0.2 g of material, on flyby E21 in October 2015 indicating a peak mass density of ∼5.5 × 10-11 kg m-3, the highest of all the flybys measured (E3, E5, E7, E9, E14, E21).

Enceladus Plume Density Modeling and Reconstruction for Cassini Attitude Control System

NASA Technical Reports Server (NTRS)

Sarani, Siamak

2010-01-01

In 2005, Cassini detected jets composed mostly of water, spouting from a set of nearly parallel rifts in the crust of Enceladus, an icy moon of Saturn. During an Enceladus flyby, either reaction wheels or attitude control thrusters on the Cassini spacecraft are used to overcome the external torque imparted on Cassini due to Enceladus plume or jets, as well as to slew the spacecraft in order to meet the pointing needs of the on-board science instruments. If the estimated imparted torque is larger than it can be controlled by the reaction wheel control system, thrusters are used to control the spacecraft. Having an engineering model that can predict and simulate the external torque imparted on Cassini spacecraft due to the plume density during all projected low-altitude Enceladus flybys is important. Equally important is being able to reconstruct the plume density after each flyby in order to calibrate the model. This paper describes an engineering model of the Enceladus plume density, as a function of the flyby altitude, developed for the Cassini Attitude and Articulation Control Subsystem, and novel methodologies that use guidance, navigation, and control data to estimate the external torque imparted on the spacecraft due to the Enceladus plume and jets. The plume density is determined accordingly. The methodologies described have already been used to reconstruct the plume density for three low-altitude Enceladus flybys of Cassini in 2008 and will continue to be used on all remaining low-altitude Enceladus flybys in Cassini's extended missions.

Oceanic magmatic evolution during ocean opening under influence of mantle plume

NASA Astrophysics Data System (ADS)

Sushchevskaya, Nadezhda; Melanholina, Elena; Belyatsky, Boris; Krymsky, Robert; Migdisova, Natalya

2015-04-01

Petrology, geochemistry and geophysics as well as numerical simulation of spreading processes in plume impact environments on examples of Atlantic Ocean Iceland and the Central Atlantic plumes and Kerguelen plume in the Indian Ocean reveal: - under interaction of large plume and continental landmass the plume can contribute to splitting off individual lithosphere blocks, and their subsequent movement into the emergent ocean. At the same time enriched plume components often have geochemical characteristics of the intact continental lithosphere by early plume exposure. This is typical for trap magmatism in Antarctica, and for magmatism of North and Central Atlantic margins; - in the course of the geodynamic reconstruction under the whole region of the South Atlantic was formed (not in one step) metasomatized enriched sub-oceanic mantle with pyroxenite mantle geochemical characteristics and isotopic composition of enriched HIMU and EM-2 sources. That is typical for most of the islands in the West Antarctic. This mantle through spreading axes jumping involved in different proportions in the melting under the influence of higher-temperature rising asthenospheric lherzolite mantle; - CAP activity was brief enough (200 ± 2 Ma), but Karoo-Maud plume worked for a longer time and continued from 180 to 170 Ma ago in the main phase. Plume impact within Antarctica distributed to the South and to the East, leading to the formation of extended igneous provinces along the Transantarctic Mountains and along the east coast (Queen Maud Land province and Schirmacher Oasis). Moreover, this plume activity may be continued later on, after about 40 million years cessation, as Kerguelen plume within the newly-formed Indian Ocean, significantly affects the nature of the rift magmatism; - a large extended uplift in the eastern part of the Indian Ocean - Southeastern Indian Ridge (SEIR) was formed on the ancient spreading Wharton ridge near active Kerguelen plume. The strongest plume influence on the SEIR formation occurred 70-50 mln years ago, when the process of primary magma generation happened at high degrees of melting (up to 30%), which is not typical for spreading ridges of the Atlantic and Pacific Oceans. According to geochemical characteristics of the Kerguelen Plateau and SEIR magma sources close to each other, and have an enriched source of more typical for Kerguelen plume magmas and diluted by depleted substance for SEIR melts. Appearance of magmatism on the Antarctic margin about 56 thousand years ago, in the form of a stratovolcano Gaussberg indicates sublithospheric Kerguelen plume distribution in the south-west direction. The source of primary magmas (lamproite composition) is an ancient Gondwana lithosphere, has undergone repeated changes in the early stages of evolution during which it was significantly enriched in volatile and lithophile elements, and radiogenic Sr and Pb.

Real-time diagnostics of a jet engine exhaust using an intra-pulse quantum cascade laser spectrometer

NASA Astrophysics Data System (ADS)

Duxbury, Geoffrey; Hay, Kenneth G.; Langford, Nigel; Johnson, Mark P.; Black, John D.

2011-09-01

It has been demonstrated that an intra-pulse scanned quantum cascade laser spectrometer may be used to obtain real-time diagnostics of the amounts of carbon monoxide, carbon dioxide, and water, in the exhaust of an aero gas turbine (turbojet) engine operated in a sea level test cell. Measurements have been made of the rapid changes in composition following ignition, the composition under steady state operating conditions, and the composition changes across the exhaust plume. The minimum detection limit for CO in a double pass through a typical gas turbine plume of 50 cm in diameter, with 0.4 seconds integration time, is approximately 2 ppm.

Estimation and Modeling of Enceladus Plume Jet Density Using Reaction Wheel Control Data

NASA Technical Reports Server (NTRS)

Lee, Allan Y.; Wang, Eric K.; Pilinski, Emily B.; Macala, Glenn A.; Feldman, Antonette

2010-01-01

The Cassini spacecraft was launched on October 15, 1997 by a Titan 4B launch vehicle. After an interplanetary cruise of almost seven years, it arrived at Saturn on June 30, 2004. In 2005, Cassini completed three flybys of Enceladus, a small, icy satellite of Saturn. Observations made during these flybys confirmed the existence of a water vapor plume in the south polar region of Enceladus. Five additional low-altitude flybys of Enceladus were successfully executed in 2008-9 to better characterize these watery plumes. The first of these flybys was the 50-km Enceladus-3 (E3) flyby executed on March 12, 2008. During the E3 flyby, the spacecraft attitude was controlled by a set of three reaction wheels. During the flyby, multiple plume jets imparted disturbance torque on the spacecraft resulting in small but visible attitude control errors. Using the known and unique transfer function between the disturbance torque and the attitude control error, the collected attitude control error telemetry could be used to estimate the disturbance torque. The effectiveness of this methodology is confirmed using the E3 telemetry data. Given good estimates of spacecraft's projected area, center of pressure location, and spacecraft velocity, the time history of the Enceladus plume density is reconstructed accordingly. The 1-sigma uncertainty of the estimated density is 7.7%. Next, we modeled the density due to each plume jet as a function of both the radial and angular distances of the spacecraft from the plume source. We also conjecture that the total plume density experienced by the spacecraft is the sum of the component plume densities. By comparing the time history of the reconstructed E3 plume density with that predicted by the plume model, values of the plume model parameters are determined. Results obtained are compared with those determined by other Cassini science instruments.

Estimation and Modeling of Enceladus Plume Jet Density Using Reaction Wheel Control Data

NASA Technical Reports Server (NTRS)

Lee, Allan Y.; Wang, Eric K.; Pilinski, Emily B.; Macala, Glenn A.; Feldman, Antonette

2010-01-01

The Cassini spacecraft was launched on October 15, 1997 by a Titan 4B launch vehicle. After an interplanetary cruise of almost seven years, it arrived at Saturn on June 30, 2004. In 2005, Cassini completed three flybys of Enceladus, a small, icy satellite of Saturn. Observations made during these flybys confirmed the existence of a water vapor plume in the south polar region of Enceladus. Five additional low-altitude flybys of Enceladus were successfully executed in 2008-9 to better characterize these watery plumes. The first of these flybys was the 50-km Enceladus-3 (E3) flyby executed on March 12, 2008. During the E3 flyby, the spacecraft attitude was controlled by a set of three reaction wheels. During the flyby, multiple plume jets imparted disturbance torque on the spacecraft resulting in small but visible attitude control errors. Using the known and unique transfer function between the disturbance torque and the attitude control error, the collected attitude control error telemetry could be used to estimate the disturbance torque. The effectiveness of this methodology is confirmed using the E3 telemetry data. Given good estimates of spacecraft's projected area, center of pressure location, and spacecraft velocity, the time history of the Enceladus plume density is reconstructed accordingly. The 1 sigma uncertainty of the estimated density is 7.7%. Next, we modeled the density due to each plume jet as a function of both the radial and angular distances of the spacecraft from the plume source. We also conjecture that the total plume density experienced by the spacecraft is the sum of the component plume densities. By comparing the time history of the reconstructed E3 plume density with that predicted by the plume model, values of the plume model parameters are determined. Results obtained are compared with those determined by other Cassini science instruments.

Estimation and Modeling of Enceladus Plume Density Using Attitude Control Data Collected by the Cassini Spacecraft During Low-Altitude Enceladus Flybys

NASA Technical Reports Server (NTRS)

Wang, Eric K.; Lee, Allan Y.

2011-01-01

The Cassini spacecraft was launched on 15 October 1997. After an interplanetary cruise of almost seven years, it arrived at Saturn on June 30, 2004. Major science objectives of the Cassini mission include investigations of the configuration and dynamics of Saturn's magnetosphere, the structure and composition of the rings, the characterization of several of Saturn's icy satellites, and Titan's atmosphere constituent abundance

Chemical Composition of African Biomass Burning Aerosols Over the Southeast Atlantic: Aerosol Mass Spectrometer Results from the 2016 and 2017 ORACLES Field Campaigns.

NASA Astrophysics Data System (ADS)

Dobracki, A. N.; Howell, S. G.; Freitag, S.; Smirnow, N.; Podolske, J. R.

2017-12-01

Biomass burning (BB) is one of the largest contributors of anthropogenic aerosols in the atmosphere. During BB events, organic and inorganic gases and particles are emitted into the atmosphere. Because of their abundance, particle size, and radiative properties, BB aerosols play an important role in global climate. Southern Africa produces 30% of the Earth's BB aerosol particles. Organics, Nitrates, sulfates, and refractory black carbon, along with other chemical species are lofted into the free troposphere and transported over the Southeast Atlantic Ocean. However, considerate uncertainty remains in the chemical composition of these plumes with its large variety of organic and inorganic species. As part of the NASA ORACLES (ObseRvations of Aerosols above CLouds and their intEractionS) 2016 and 2017 airborne field campaigns, an Aerosol Mass Spectrometer (AMS) was used to sample the chemical composition and chemical structure of the aerosol in this region. Results show constant vertical stratification within the plume over the course of the campaign (August 2017 / September 2016). Using nitrate (NO3) and organic carbon (OC) as two tracers, the structure of the September 2016 plume had a ratio of 1:8 (NO3:OC) in the upper plume (3km-5km), while the lower plume (1km-2.5km) had a ratio of 1:12 (NO3:OC). AMS measurements were supported by carbon monoxide (CO) and carbon dioxide (CO2) measurements. This data revealed a modified combustion efficiency (MCE= ΔCO2/ΔCO2 + ΔCO) of <0.97 in the upper plume, and a higher MCE > 0.97 in the lower plume. An MCE above 0.9 represents efficient burning processes. Additionally, concentrations of C2(H2O)2 (m/z60), a common chemical fragment from breaking up carbohydrates (primarily levoglucosan) emitted by burning biomass only represented <1% of total organics throughout the campaign. These low concentrations are due to efficient combustion rather than oxidation during transport. These results are consistent with earlier studies of efficient fires.

Mercury emissions and stable isotopic compositions at Vulcano Island (Italy)

NASA Astrophysics Data System (ADS)

Zambardi, T.; Sonke, J. E.; Toutain, J. P.; Sortino, F.; Shinohara, H.

2009-01-01

Sampling and analyses methods for determining the stable isotopic compositions of Hg in an active volcanic system were tested and optimized at the volcanic complex of Vulcano (Aeolian Islands, Italy). Condensed gaseous fumarole Hg (fum)T, plume gaseous elemental Hg (g)0 and plume particulate Hg (p)II were obtained at fumaroles F0, F5, F11, and FA. The average total Hg emissions, based on Hg T/SO 2 in condensed fumarolic gases and plumes, range from 2.5 to 10.1 kg y - 1 , in agreement with published values [Ferrara, R., Mazzolai, B., Lanzillotta, E., Nucaro, E., Pirrone, N., 2000. Volcanoes as emission sources of atmospheric mercury in the Mediterranean Basin. Sci. Total Environ. 259(1-3), 115-121; Aiuppa, A., Bagnato, E., Witt, M.L.I., Mather, T.A., Parello, F., Pyle, D.M., Martin, R.S., 2007. Real-time simultaneous detection of volcanic Hg and SO 2 at La Fossa Crater, Vulcano (Aeolian Islands, Sicily). Geophys. Res. Lett. 34(L21307).]. Plume Hg (p)II increases with distance from the fumarole vent, at the expense of Hg (g)0 and indicates significant in-plume oxidation and condensation of fumarole Hg (fum)T. Relative to the NIST SRM 3133 Hg standard, the stable isotopic compositions of Hg are δ 202Hg (fum)T = - 0.74‰ ± 0.18 (2SD, n = 4) for condensed gaseous fumarole Hg (fum)T, δ 202Hg (g)0 = - 1.74‰ ± 0.36 (2SD, n = 1) for plume gaseous elemental Hg (g)0 at the F0 fumarole, and δ 202Hg (p)II = - 0.11‰ ± 0.18 (2SD, n = 4) for plume particulate Hg (p)II. The enrichment of Hg (p)II in the heavy isotopes and Hg (g)0 in the light isotopes relative to the total condensed fumarolic Hg (fum)T gas complements the speciation data and demonstrates a gas-particle fractionation occurring after the gas expulsion in ambient T° atmosphere. A first order Rayleigh equilibrium condensation isotope fractionation model yields a fractionation factor α cond-gas of 1.00135 ± 0.00058.

Ozone production efficiency of a ship-plume: ITCT 2K2 case study.

PubMed

Kim, Hyun S; Kim, Yong H; Han, Kyung M; Kim, Jhoon; Song, Chul H

2016-01-01

Ozone production efficiency (OPE) of ship plume was first evaluated in this study, based on ship-plume photochemical/dynamic model simulations and the ship-plume composition data measured during the ITCT 2K2 (Intercontinental Transport and Chemical Transformation 2002) aircraft campaign. The averaged instantaneous OPEs (OPE(i)‾) estimated via the ship-plume photochemical/dynamic modeling for the ITCT 2K2 ship-plume ranged between 4.61 and 18.92, showing that the values vary with the extent of chemical evolution (or chemical stage) of the ship plume and the stability classes of the marine boundary layer (MBL). Together with OPE(i)‾, the equivalent OPEs (OPE(e)‾) for the entire ITCT 2K2 ship-plume were also estimated. The OPE(e)‾ values varied between 9.73 (for the stable MBL) and 12.73 (for the moderately stable MBL), which agreed well with the OPE(e)‾ of 12.85 estimated based on the ITCT 2K2 ship-plume observations. It was also found that both the model-simulated and observation-based OPE(e)‾ inside the ship-plume were 0.29-0.38 times smaller than the OPE(e)‾ calculated/measured outside the ITCT 2K2 ship-plume. Such low OPEs insides the ship plume were due to the high levels of NO and non-liner ship-plume photochemistry. Possible implications of this ship-plume OPE study in the global chemistry-transport modeling are also discussed. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Plume composition and volatile flux of Nyamulagira volcano, Democratic Republic of Congo, during birth and evolution of the lava lake, 2014-2015

NASA Astrophysics Data System (ADS)

Bobrowski, N.; Giuffrida, G. B.; Arellano, S.; Yalire, M.; Liotta, M.; Brusca, L.; Calabrese, S.; Scaglione, S.; Rüdiger, J.; Castro, J. M.; Galle, B.; Tedesco, D.

2017-12-01

Very little is known about the volatile element makeup of the gaseous emissions of Nyamulagira volcano. This paper tries to fill this gap by reporting the first gas composition measurements of Nyamulagira's volcanic plume since the onset of its lava lake activity at the end of 2014. Two field surveys were carried out on 1 November 2014, and 13-15 October 2015. We applied a broad toolbox of volcanic gas composition measurement techniques in order to geochemically characterize Nyamulagira's plume. Nyamulagira is a significant emitter of SO2, and our measurements confirm this, as we recorded SO2 emissions of up to 14 kt/d during the studied period. In contrast to neighbouring Nyiragongo volcano, however, Nyamulagira exhibits relatively low CO2/SO2 molar ratios (< 4) and a high H2O content (> 92% of total gas emissions). Strong variations in the volatile composition, in particular for the CO2/SO2 ratio, were measured between 2014 and 2015, which appear to reflect the simultaneous variations in volcanic activity. We also determined the molar ratios for Cl/S, F/S and Br/S in the plume gas, finding values of 0.13 and 0.17, 0.06 and 0.11, and 2.3·10-4 and 1·10-4, in 2014 and 2015, respectively. A total gas emission flux of 48 kt/d was estimated for 2014. The I/S ratio in 2015 was found to be 3.6·10-6. In addition, we were able to distinguish between hydrogen halides and non-hydrogen halides in the volcanic plume. Considerable amounts of bromine (18-35% of total bromine) and iodine (8-18% of total iodine) were found in compounds other than hydrogen halides. However, only a negligible fraction of chlorine was found as compounds other than hydrogen chloride.

Garnet Pyroxenites from Kaula, Hawaii: Implications for Plume-Lithosphere Interaction

NASA Astrophysics Data System (ADS)

Bizimis, M.; Garcia, M. O.; Norman, M. D.

2006-12-01

The presence of garnet pyroxenite xenoliths on Oahu and Kaula Islands, Hawaii, provides the rare opportunity to investigate the composition of the deeper oceanic mantle lithosphere and the nature of plume-lithosphere interaction in two dimensions, downstream from the center of the Hawaiian plume. Kaula (60 miles SW of Kauai) is on the same bathymetric shallow as Kauai and the Kaula-Niihau-Kauai islands form a cross-trend relationship to the Hawaiian Island ridge. Here, we present the first Sr-Nd isotope data on clinopyroxenes (cpx) from Kaula pyroxenites, and we compare them with the Salt Lake Crater (SLC) pyroxenites from Oahu. The Kaula cpx major element compositions overlap those of the (more variable) SLC pyroxenites (e.g. Mg# = 0.79-0.83), except for their higher Al2O3 contents (9% vs. 5-8%) than the SLC. The Kaula cpx are LREE enriched with elevated Dy/Yb ratios, similar to the SLC pyroxenites and characteristic of the presence of garnet that preferentially incorporates the HREE. In Sr-Nd isotope space, the Kaula pyroxenite compositions (87Sr/86Sr= 0.70312-0.70326, ɛNd= 7.2-8.6) overlap those of both the Oahu-Kauai post erosional lavas and the SLC pyroxenites, falling at the isotopically depleted end of the Hawaiian lava compositions. The depleted Sr-Nd isotope compositions of the Kaula pyroxenites suggest that they are not related to the isotopically enriched shield stage Hawaiian lavas, either as a source material (i.e. recycled eclogite) or as cumulates. Their elevated 87Sr/86Sr ratios relative to MORB also suggests that they are not likely MORB-related cumulates. The similarities between the Oahu and Kaula pyroxenites, some 200 km apart, suggest the widespread presence of pyroxenitic material in the deeper (>60km) Pacific lithosphere between Oahu and Kaula-Kauai, as high pressure cumulates from melts isotopically similar to the secondary Hawaiian volcanism. The presence of this material within the lower lithosphere is consistent with seismic observations suggesting erosion and replacement of the deeper Pacific lithosphere by plume material, downstream from the center of the plume.

Influence of main forcing affecting the Tagus turbid plume under high river discharges using MODIS imagery

PubMed Central

Gómez-Gesteira, M.; Mendes, R.; deCastro, M.; Vaz, N.; Dias, J. M.

2017-01-01

The role of river discharge, wind and tide on the extension and variability of the Tagus River plume was analyzed from 2003 to 2015. This study was performed combining daily images obtained from the Moderate Resolution Imaging Spectroradiometer (MODIS) sensor located onboard the Aqua and Terra satellites. Composites were generated by averaging pixels with the same forcing conditions. River discharge shows a strong relation with the extension of the Tagus plume. The plume grows with the increasing river discharge and express a two day lag caused by the long residence time of water within the estuary. The Tagus turbid plume was found to be smaller under northerly and easterly winds, than under southerly and westerly winds. It is suggested that upwelling favoring winds provoke the offshore movement of the plume material with a rapidly decrease in turbidity values whereas downwelling favoring winds retain plume material in the north coast close to the Tagus mouth. Eastern cross-shore (oceanward) winds spread the plume seaward and to the north following the coast geometry, whereas western cross-shore (landward) winds keep the plume material in both alongshore directions occupying a large part of the area enclosed by the bay. Low tides produce larger and more turbid plumes than high tides. In terms of fortnightly periodicity, the maximum plume extension corresponding to the highest turbidity is observed during and after spring tides. Minimum plume extension associated with the lowest turbidity occurs during and after neap tides. PMID:29073209

Influence of main forcing affecting the Tagus turbid plume under high river discharges using MODIS imagery.

PubMed

Fernández-Nóvoa, D; Gómez-Gesteira, M; Mendes, R; deCastro, M; Vaz, N; Dias, J M

2017-01-01

The role of river discharge, wind and tide on the extension and variability of the Tagus River plume was analyzed from 2003 to 2015. This study was performed combining daily images obtained from the Moderate Resolution Imaging Spectroradiometer (MODIS) sensor located onboard the Aqua and Terra satellites. Composites were generated by averaging pixels with the same forcing conditions. River discharge shows a strong relation with the extension of the Tagus plume. The plume grows with the increasing river discharge and express a two day lag caused by the long residence time of water within the estuary. The Tagus turbid plume was found to be smaller under northerly and easterly winds, than under southerly and westerly winds. It is suggested that upwelling favoring winds provoke the offshore movement of the plume material with a rapidly decrease in turbidity values whereas downwelling favoring winds retain plume material in the north coast close to the Tagus mouth. Eastern cross-shore (oceanward) winds spread the plume seaward and to the north following the coast geometry, whereas western cross-shore (landward) winds keep the plume material in both alongshore directions occupying a large part of the area enclosed by the bay. Low tides produce larger and more turbid plumes than high tides. In terms of fortnightly periodicity, the maximum plume extension corresponding to the highest turbidity is observed during and after spring tides. Minimum plume extension associated with the lowest turbidity occurs during and after neap tides.

Geochemical nature of sub-ridge mantle and opening dynamics of the South China Sea

NASA Astrophysics Data System (ADS)

Zhang, Guo-Liang; Luo, Qing; Zhao, Jian; Jackson, Matthew G.; Guo, Li-Shuang; Zhong, Li-Feng

2018-05-01

The Indian-type mantle (i.e., above the north hemisphere reference line on the plot of 208Pb/204Pb vs. 206Pb/204Pb) has been considered as a "Southern Hemisphere" geochemical signature, whose origin remains enigmatic. The South China Sea is an extensional basin formed after rifting of the Euro-Asia continent in the Northern Hemisphere, however, the geochemical nature of the igneous crust remains unexplored. For the first time, IODP Expedition 349 has recovered seafloor basalts covered by the thick sediments in the Southwest sub-basin (Sites U1433 and U1434) and the East sub-basin (Site U1431). The Southwest sub-basin consists of enriched (E)-MORB type basalts, and the East sub-basin consists of both normal (N)-MORB-type and E-MORB-type basalts based on trace element compositions. The basalts of the two sub-basins are Indian-type MORBs based on Sr-Nd-Pb-Hf isotope compositions, and the Southwest sub-basin basalts show isotopic compositions (i.e., 206Pb/204Pb of 17.59-17.89) distinctly different from the East sub-basin (i.e., 206Pb/204Pb of 18.38-18.57), suggesting a sub-basin scale mantle compositional heterogeneity and different histories of mantle compositional evolution. Two different enriched mantle end-members (EM1 and EM2) are responsible for the genesis of the Indian-type mantle in the South China Sea. We have modeled the influences of Hainan mantle plume and lower continental crust based on Sr-Nd-Pb-Hf isotope compositions. The results indicate that the influence of Hainan plume can explain the elevated 206Pb/204Pb of the East sub-basin basalts, and the recycling of lower continental crust can explain the low 206Pb/204Pb of the Southwest sub-basin basalts. Based on the strong geochemical imprints of Hainan plume in the ridge magmatism, we propose that the Hainan plume might have promoted the opening of the South China Sea, during which the Hainan plume contributed enriched component to the sub-ridge mantle and caused thermal erosion and return of lower continental crust to the convective mantle. These results imply an in situ origin of the Indian-type mantle that can help understand the genesis of the "Southern Hemisphere" geochemical anomaly in the Northern Hemispheric extensional basin.

The origin of alkaline magmas in an intraplate setting near a subduction zone: the Ngatutura Basalts, North Island, New Zealand

NASA Astrophysics Data System (ADS)

Briggs, R. M.; Utting, A. J.; Gibson, I. L.

1990-01-01

The Ngatutura Basalts are one of a series of Pliocene-Quaternary alkalic basalt volcanic fields in North Island, New Zealand. They are situated in an intraplate tectonic setting behind the currently active Taupo Volcanic Zone, and 300 km above the subducting slab. The volcanic field consists of 16 small-volume monogenetic volcanic centres composed mainly of eroded scoria cones and lava flows, that occupy an extensional tectonic environment characterized by NE-striking block faulting. In some cases the faults have controlled the localization of volcanic vents. The lavas have restricted compositions, ranging from hawaiites to nepheline hawaiites, and are characterized by enriched LILE, LREE, and HFS elements, with particularly high Nb and Ta, low Ba/Nb, and high Zr/Y and Ce N/Yb N ratios. Nepheline hawaiites are slightly more differentiated than hawaiites and have higher Ce N/Yb N ratios. Petrogenetic modelling suggests that the range in composition was mainly controlled by fractional crystallization of olivine, clinopyroxene, and minor plagioclase and titanomagnetite, which is consistent with the modal phenocryst abundances. Fractionation is explained by side-wall crystallization and flowage differentiation during rapid ascent, rather than gravitative settling in a magma chamber. Ngatutura magmas were probably derived from an enriched garnet lherzolite source within the low-velocity mantle. The process of source enrichment is speculative but our preferred model calls on metasomatizing fluids in the low-velocity zone. There is no geochemical evidence for any influence of the subducted slab on their composition, even though they overlie the Pacific plate subduction zone. This implies that the extent of subduction-related contamination in the mantle wedge is not pervasive, but is confined to a limited region overlying the subducted slab. Also, the "deep mantle plume" responsible for alkalic magmatism must have originated above the slab, because it seems unlikely that such a plume could have occurred at a deeper level and penetrate the slab without some evidence. This therefore limits the depth of origin of these "deep mantle plumes" to less than 300 km.

Sediment and Turbidity Associated with Offshore Dredging Increase Coral Disease Prevalence on Nearby Reefs

PubMed Central

Pollock, F. Joseph; Lamb, Joleah B.; Field, Stuart N.; Heron, Scott F.; Schaffelke, Britta; Shedrawi, George; Bourne, David G.; Willis, Bette L.

2014-01-01

In recent decades, coral reef ecosystems have declined to the extent that reefs are now threatened globally. While many water quality parameters have been proposed to contribute to reef declines, little evidence exists conclusively linking specific water quality parameters with increased disease prevalence in situ. Here we report evidence from in situ coral health surveys confirming that chronic exposure to dredging-associated sediment plumes significantly increase the prevalence of white syndromes, a devastating group of globally important coral diseases. Coral health surveys were conducted along a dredging-associated sediment plume gradient to assess the relationship between sedimentation, turbidity and coral health. Reefs exposed to the highest number of days under the sediment plume (296 to 347 days) had two-fold higher levels of disease, largely driven by a 2.5-fold increase in white syndromes, and a six-fold increase in other signs of compromised coral health relative to reefs with little or no plume exposure (0 to 9 days). Multivariate modeling and ordination incorporating sediment exposure level, coral community composition and cover, predation and multiple thermal stress indices provided further confirmation that sediment plume exposure level was the main driver of elevated disease and other compromised coral health indicators. This study provides the first evidence linking dredging-associated sedimentation and turbidity with elevated coral disease prevalence in situ. Our results may help to explain observed increases in global coral disease prevalence in recent decades and suggest that minimizing sedimentation and turbidity associated with coastal development will provide an important management tool for controlling coral disease epizootics. PMID:25029525

Sediment and turbidity associated with offshore dredging increase coral disease prevalence on nearby reefs.

PubMed

Pollock, F Joseph; Lamb, Joleah B; Field, Stuart N; Heron, Scott F; Schaffelke, Britta; Shedrawi, George; Bourne, David G; Willis, Bette L

2014-01-01

In recent decades, coral reef ecosystems have declined to the extent that reefs are now threatened globally. While many water quality parameters have been proposed to contribute to reef declines, little evidence exists conclusively linking specific water quality parameters with increased disease prevalence in situ. Here we report evidence from in situ coral health surveys confirming that chronic exposure to dredging-associated sediment plumes significantly increase the prevalence of white syndromes, a devastating group of globally important coral diseases. Coral health surveys were conducted along a dredging-associated sediment plume gradient to assess the relationship between sedimentation, turbidity and coral health. Reefs exposed to the highest number of days under the sediment plume (296 to 347 days) had two-fold higher levels of disease, largely driven by a 2.5-fold increase in white syndromes, and a six-fold increase in other signs of compromised coral health relative to reefs with little or no plume exposure (0 to 9 days). Multivariate modeling and ordination incorporating sediment exposure level, coral community composition and cover, predation and multiple thermal stress indices provided further confirmation that sediment plume exposure level was the main driver of elevated disease and other compromised coral health indicators. This study provides the first evidence linking dredging-associated sedimentation and turbidity with elevated coral disease prevalence in situ. Our results may help to explain observed increases in global coral disease prevalence in recent decades and suggest that minimizing sedimentation and turbidity associated with coastal development will provide an important management tool for controlling coral disease epizootics.

Total peroxy nitrates and ozone production : analysis of forest fire plumes during BORTAS campaign

NASA Astrophysics Data System (ADS)

Busilacchio, Marcella; Di Carlo, Piero; Aruffo, Eleonora; Biancofiore, Fabio; Giammaria, Franco; Bauguitte, Stephane; Lee, James; Moller, Sarah; Lewis, Ally; Parrington, Mark; Palmer, Paul; Dari Salisburgo, Cesare

2014-05-01

The goal of this work is to investigate the connection between PNS and ozone within plumes emitted from boreal forest fires and the possible perturbation to oxidant chemistry in the troposphere. During the Aircraft campaign in Canada called BORTAS (summer 2011 ) were carried out several profiles from ground up to 10 km with the BAe-146 aircraft to observe the atmospheric composition inside and outside fire plumes. The BORTAS flights have been selected based on the preliminary studies of 'Plume identification', selecting those effected by Boreal forest fire emissions (CO > 200 ppbv). The FLAMBE fire counts were used concertedly with back trajectory calculations generated by the HYbrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model to locate the sources of Boreal biomass burning.Profiles measured on board the BAe-146 aircraft are used to calculate the productions of PNs and O3 within the biomass burning plume. By selecting the flights that intercept the biomass burning plume, we evaluate the ratio between the ozone production and the PNs production within the plume. Analyzing this ratio it is possible to determine whether O3 production or PNs production is the dominant process in the biomass burning boreal plume detected during BORTAS campaign.

Effects of plume afterburning on infrared spectroscopy

NASA Astrophysics Data System (ADS)

Zhu, Xijuan; Xu, Ying; Ma, Jing; Duan, Ran; Wu, Jie

2017-10-01

Contains H2, CO and unburned components of high-temperature plume of rocket engine, then injected into the atmosphere, continue to carry out the oxidation reaction in the plume near field region with the volume in the plume of oxygen in the air, two times burning. The afterburning is an important cause of infrared radiation intensification of propellant plume, which increases the temperature of the flame and changes the components of the gas, thus enhancing the infrared radiation intensity of the flame. [1]. Two the combustion numerical using chemical reaction mechanism involving HO2 intermediate reaction, the study confirmed that HO2 is a key intermediate, plays a decisive role to trigger early response, on afterburning temperature and flow concentration distribution effect. A finite rate chemical reaction model is used to describe the two burning phenomenon in high temperature plume[2]. In this paper, a numerical simulation of the flame flow field and radiative transfer is carried out for the afterburning phenomenon. The effects of afterburning on the composition, temperature and infrared radiation of the plume are obtained by comparison.

Simulation of Deepwater Horizon oil plume reveals substrate specialization within a complex community of hydrocarbon degraders.

PubMed

Hu, Ping; Dubinsky, Eric A; Probst, Alexander J; Wang, Jian; Sieber, Christian M K; Tom, Lauren M; Gardinali, Piero R; Banfield, Jillian F; Atlas, Ronald M; Andersen, Gary L

2017-07-11

The Deepwater Horizon (DWH) accident released an estimated 4.1 million barrels of oil and 10 10 mol of natural gas into the Gulf of Mexico, forming deep-sea plumes of dispersed oil droplets and dissolved gases that were largely degraded by bacteria. During the course of this 3-mo disaster a series of different bacterial taxa were enriched in succession within deep plumes, but the metabolic capabilities of the different populations that controlled degradation rates of crude oil components are poorly understood. We experimentally reproduced dispersed plumes of fine oil droplets in Gulf of Mexico seawater and successfully replicated the enrichment and succession of the principal oil-degrading bacteria observed during the DWH event. We recovered near-complete genomes, whose phylogeny matched those of the principal biodegrading taxa observed in the field, including the DWH Oceanospirillales (now identified as a Bermanella species), multiple species of Colwellia , Cycloclasticus , and other members of Gammaproteobacteria, Flavobacteria, and Rhodobacteria. Metabolic pathway analysis, combined with hydrocarbon compositional analysis and species abundance data, revealed substrate specialization that explained the successional pattern of oil-degrading bacteria. The fastest-growing bacteria used short-chain alkanes. The analyses also uncovered potential cooperative and competitive relationships, even among close relatives. We conclude that patterns of microbial succession following deep ocean hydrocarbon blowouts are predictable and primarily driven by the availability of liquid petroleum hydrocarbons rather than natural gases.

Simulation of Deepwater Horizon oil plume reveals substrate specialization within a complex community of hydrocarbon degraders

PubMed Central

Hu, Ping; Probst, Alexander J.; Wang, Jian; Sieber, Christian M. K.; Tom, Lauren M.; Gardinali, Piero R.; Banfield, Jillian F.; Atlas, Ronald M.

2017-01-01

The Deepwater Horizon (DWH) accident released an estimated 4.1 million barrels of oil and 1010 mol of natural gas into the Gulf of Mexico, forming deep-sea plumes of dispersed oil droplets and dissolved gases that were largely degraded by bacteria. During the course of this 3-mo disaster a series of different bacterial taxa were enriched in succession within deep plumes, but the metabolic capabilities of the different populations that controlled degradation rates of crude oil components are poorly understood. We experimentally reproduced dispersed plumes of fine oil droplets in Gulf of Mexico seawater and successfully replicated the enrichment and succession of the principal oil-degrading bacteria observed during the DWH event. We recovered near-complete genomes, whose phylogeny matched those of the principal biodegrading taxa observed in the field, including the DWH Oceanospirillales (now identified as a Bermanella species), multiple species of Colwellia, Cycloclasticus, and other members of Gammaproteobacteria, Flavobacteria, and Rhodobacteria. Metabolic pathway analysis, combined with hydrocarbon compositional analysis and species abundance data, revealed substrate specialization that explained the successional pattern of oil-degrading bacteria. The fastest-growing bacteria used short-chain alkanes. The analyses also uncovered potential cooperative and competitive relationships, even among close relatives. We conclude that patterns of microbial succession following deep ocean hydrocarbon blowouts are predictable and primarily driven by the availability of liquid petroleum hydrocarbons rather than natural gases. PMID:28652349

Lidar and airborne investigation of smoke plume characteristics: Kootenai Creek Fire case study

Treesearch

S. Urbanski; V. Kovalev; W. M. Hao; C. Wold; A. Petkov

2010-01-01

A ground-based scanning lidar was utilized with a set of airborne instruments to acquire measurements of smoke plume dynamics, smoke aerosol distribution and chemical composition in the vicinity of active wildfires in the western U.S. A new retrieval technique was used for processing lidar multiangle measurements. The technique determines the location of...

Structure of hydrothermal plumes at the Logatchev vent field, 14°45‧N, Mid-Atlantic Ridge: evidence from geochemical and geophysical data

NASA Astrophysics Data System (ADS)

Sudarikov, S. M.; Roumiantsev, A. B.

2000-09-01

In the Seventh cruise of R/V ;Professor Logatchev; anomalies of natural electric field (EF), Eh and pS were discovered using a towed instrument package (RIFT) at 14°45‧N on the MAR (Logatchev hydrothermal field). The anomalous zone (AZ) is situated close (10-35 m) to two low-temperature venting areas of degrading sulphides and a black smoker (Irina-Microsmoke) forming a distinct buoyant plume. Over or close to the main area of high-temperature venting situated to the south-east from the AZ, no EF or Eh anomalies were observed. According to the results of Mir dives the highly mineralised solutions from smoking craters at the main mound mostly form non-buoyant plumes (reverse-plumes). The buoyant plume structure shows the differentiation of the electrical and Eh fields within the plume. Maxima of the EF, Eh and EH2S anomalies were revealed in the lower part (∼15 m) of the plume. The negative redox potential plume coupled with a sulphide anomaly is more localized in comparison with the EF. This observation indicates a distinct change in the composition of buoyant plume water, which may be due to the formation and fallout of early formed Fe sulphide particles soon after venting.

Plume Collection Strategies for Icy World Sample Return

NASA Technical Reports Server (NTRS)

Neveu, M.; Glavin, D. P.; Tsou, P.; Anbar, A. D.; Williams, P.

2015-01-01

Three icy worlds in the solar system display evidence of pluming activity. Water vapor and ice particles emanate from cracks near the south pole of Saturn's moon Enceladus. The plume gas contains simple hydrocarbons that could be fragments of larger, more complex organics. More recently, observations using the Hubble and Herschel space telescopes have hinted at transient water vapor plumes at Jupiter's moon Europa and the dwarf planet Ceres. Plume materials may be ejected directly from possible sub-surface oceans, at least on Enceladus. In such oceans, liquid water, organics, and energy may co-exist, making these environments habitable. The venting of habitable ocean material into space provides a unique opportunity to capture this material during a relatively simple flyby mission and return it to Earth. Plume collection strategies should enable investigations of evidence for life in the returned samples via laboratory analyses of the structure, distribution, isotopic composition, and chirality of the chemical components (including biomolecules) of plume materials. Here, we discuss approaches for the collection of dust and volatiles during flybys through Enceladus' plume, based on Cassini results and lessons learned from the Stardust comet sample return mission. We also highlight areas where sample collector and containment technology development and testing may be needed for future plume sample return missions.

Molecular Composition Analysis of Distant Targets

NASA Technical Reports Server (NTRS)

Hughes, Gary B.; Lubin, Philip

2017-01-01

This document is the Final Report for NASA Innovative Advanced Concepts (NIAC) Phase I Grant 15-NIAC16A-0145, titled Molecular Composition Analysis of Distant Targets. The research was focused on developing a system concept for probing the molecular composition of cold solar system targets, such as Asteroids, Comets, Planets and Moons from a distant vantage, for example from a spacecraft that is orbiting the target (Hughes et al., 2015). The orbiting spacecraft is equipped with a high-power laser, which is run by electricity from photovoltaic panels. The laser is directed at a spot on the target. Materials on the surface of the target are heated by the laser beam, and begin to melt and then evaporate, forming a plume of asteroid molecules in front of the heated spot. The heated spot glows, producing blackbody illumination that is visible from the spacecraft, via a path through the evaporated plume. As the blackbody radiation from the heated spot passes through the plume of evaporated material, molecules in the plume absorb radiation in a manner that is specific to the rotational and vibrational characteristics of the specific molecules. A spectrometer aboard the spacecraft is used to observe absorption lines in the blackbody signal. The pattern of absorption can be used to estimate the molecular composition of materials in the plume, which originated on the target. Focusing on a single spot produces a borehole, and shallow subsurface profiling of the targets bulk composition is possible. At the beginning of the Phase I research, the estimated Technology Readiness Level (TRL) of the system was TRL-1. During the Phase I research, an end-to-end theoretical model of the sensor system was developed from first principles. The model includes laser energy and optical propagation, target heating, melting and evaporation of target material, plume density, thermal radiation from the heated spot, molecular cross section of likely asteroid materials, and estimation of the absorption profile at a distant spectrometer. Results obtained by executing simulations based on the model provide compelling evidence that the concept of remote laser evaporative molecular absorption spectroscopy is feasible. In this document, technical details of the model are presented, and results of simulations are described that indicate the utility of the proposed sensor system. Additionally, an asteroid rendezvous mission is analyzed, with a survey of system requirements to accomplish molecular composition analysis of the asteroid. Based on positive theoretical results obtained during Phase I, the estimated TRL of the system is now TRL-2. This document also describes potential future research and experimentation that could push the system to TRL-4 within 2 years. Steps required for construction of a laboratory prototype are described. An experiment to test predictions of the theory is described, based on the laboratory prototype setup.

Air Force Research Laboratory (AFRL) research highlights, September--October 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

New AFOSR-sponsored research shows that exhausts from solid-fueled rocket motors have very limited impact on stratospheric ozone. The research provides the Air Force with hard data to support continued access to space using the existing fleet of rockets and rocket technology. This basic research data allows the Air Force to maintain a strongly proactive environmental stance, and to meet federal guidelines regarding environmental impacts. Long-standing conjecture within the international rocket community suggests that chlorine compounds and alumina particulates produced in solid rocket motor (SRM) exhausts could create localized, temporary ozone toss in rocket plumes following launches. The extent of amore » local depletion of ozone and its environmental impact depends on details of the composition and chemistry in these plumes. Yet direct measurements of plume composition and plume chemistry in the stratosphere had never been made. Uncertainty about these details left the Air Force and commercial space launch capability potentially vulnerable to questions about the environmental impact of rocket launches. In 1995, APOSR and the Space and Missiles Systems Center Launch Programs Office (SMC/CL) jointly began the Rocket Impacts on Stratospheric Ozone (RISO) program to make the first-ever detailed measurements of rocket exhaust plumes. These measurements were aimed at understanding how the exhaust from large rocket motors effect the Earth`s stratospheric ozone layer. The studies determined: the size distribution of alumina particles in these exhausts, the amount of reactive chlorine in SRM exhaust, and the size and duration of localized ozone toss in the rocket plumes.« less

UV Detection and Characterization of Plume Activity

NASA Astrophysics Data System (ADS)

Hansen, C. J.; Esposito, L. W.; Hendrix, A. R.

2017-12-01

Observations at ultraviolet wavelengths offer multiple techniques for detecting and characterizing plumes of gas erupting from planetary bodies. At Enceladus and Europa, UV observations include emission and absorption by water vapor molecules, and reflectance from ice particles. Emission: Emission features from electrons' interaction with water products H, OH, O and O2 can signal the presence of a plume. OH and O form a torus in the Saturn system, supplied by Enceladus' water vapor plume, that was detected before Cassini arrived in orbit [1, 2]. The nature of the ratio of H, O, and O2 emissions from Europa allow separation of the possible presence of plume(s) from Europa's O2 exosphere [3]. Absorption: The spectrum of starlight transmitted through an absorbing gas will have attenuation at UV wavelengths that are diagnostic of the composition of the gas. At Enceladus stellar and solar occultations by Enceladus' plume showed the primary composition to be water, constrained plume dimensions and revealed the presence of imbedded supersonic jets [4]. The amount of water coming from Enceladus and its variability over a decade has been measured [5]. Using Saturn as a source was not useful for Enceladus when it was observed in transit across Saturn. In contrast the putative detection of plume(s) at Europa has been bolstered by evidence that reflected light from Jupiter was being absorbed at particular places along Europa's limb as it transited Jupiter [6]. This contrast may reveal fundamental differences in the plumes at Europa and Enceladus [7]. Reflectance: With extremely long integration times the Enceladus plume has been observed reflecting light - light which is in turn absorbed by a small percentage of C2H4 gas being expelled [8]. The ice grain / gas ratio has been estimated by comparison of reflected light at near-IR wavelengths to the gas absorption of sunlight in the UV [9]. [1] Shemansky, D. E. et al. (1993) Nature 363:329; [2] Esposito, L. W. et al. (2005) Science 307:1251; [3] Roth, L. et al. (2013) Science 10.1126/1247051; [4] Hansen, C. J. et al. (2011) GRL 38:L11202; [5] Hansen, C. J. (2017) GRL 44:1; [6] Sparks, W. et al. (2016) Ast J 829:121; [7] Esposito, L. W. et al. (2017) IPPW abstract; [8] Shemansky, D. et al. (2016) AOGS abstract PS06-D5-PM2-P-022. [9] Hedman, M. et al. (2017), submitted.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurz, M.D.; Geist, D.

The authors have measured the isotopes of He, Sr, Nd and Pb in a number of lava flows from the Galapagos Archipelago; the main goal is to use magmatic helium as a tracer of plume influence in the western volcanoes. Because the Galapagos lava flows are so well preserved, it is also possible to measure surface exposure ages using in situ cosmic-ray-produced {sup 3}He. The exposure ages range from {lt}0.1 to 580 Ka, are consistent with other chronological constrains, and provide the first direct dating of these lava flows. The new age data demonstrate the utility of the technique inmore » this important age range and show that the western Galapagos volcanoes have been erupting distance compositions simultaneously for the last {approximately}10 Ka. The magmatic {sup 3}He/{sup 4}He ratios range from 6.0 to 27 times atmospheric (R{sub a}), with the highest values found on the islands of Isabella (16.8 R{sub a} for Vulcan Sierra Negra) and Fernandina (23 to 27 R{sub a}). Values from Santa Cruz are close to typical mid-ocean ridge basalt values (MORB, of {approximately}9 R{sub 2}) and Pinta has a {sup 3}He/{sup 4}He ratio lower than MORB (6.9 R{sub a}). These data confirm that the plume is centered beneath Fernandina which is the most active volcano in the archipelago and is at the leading edge of plate motion. The data are consistent with previous isotopic studies, confirming extensive contributions from depleted asthenospheric or lithospheric mantle sources, especially to the central islands. The most striking aspect of the helium isotopic data is that the {sup 3}He/{sup 4}He ratios decrease systematically in all directions from Fernandina. This spatial variability is assumed to reflect the contribution of the purest plume component to Fernandina magmatism, and shows that helium is a sensitive indicator of plume influence. The highest {sup 3}He/{sup 4}He ratios are found in volcanoes with lowest Na{sub 2}O(8) and FeO(8), which may relate to source composition as well as degree and depth of melting. An excellent correlation is observed between {sup 3}He/{sup 4}He and Nb/La, suggesting that the Galapagos plume source is characterized by high concentrations of Nb (and Ta). The major and trace element correlations demonstrate that helium is controlled by silicate melting and source variations rather than degassing and/or metasomatic processes. Although lavas with radiogenic isotopic compositions tend to have higher {sup 3}He/{sup 4}He, the island-wide isotopic variability cannot be explained by simple two components mixing alone. The preferred model to explain the isotopic data includes a heterogeneous plume, centered at Fernandina, which undergoes polybaric melting, and spatial divergence and mixing with asthenospheric material at shallower depths. The unique regional pattern of the helium isotopic data suggests that helium is extracted more efficiently than other elements during the early stages of melting in the ascending plume.« less

Simulation of the Intercontinental Transport, Aging, and Removal of a Boreal Fire Smoke Plume

NASA Astrophysics Data System (ADS)

Ghan, S. J.; Chapman, E. G.; Easter, R. C.; Reid, J. S.; Justice, C.

2003-12-01

Back trajectories suggest that an elevated absorbing aerosol plume observed over Oklahoma in May 2003 can be traced to intense forest fires in Siberia two weeks earlier. The Fire Locating and Modeling of Burning Emissions (FLAMBE) product is used to estimate smoke emissions from those fires. The Model for Integrated Research on Atmospheric Model Exchanges (MIRAGE) is used to simulate the transport, aging, radiative properties, and removal of the aerosol. The simulated aerosol optical depth is compared with satellite retrievals, and the vertical structure of the plume is compared with in situ measurements. Sensitivity experiments are performed to determine the sensitivity of the simulated plume to uncertainty in the emissions vertical profile, mass flux, size distribution, and composition.

Lidar sounding of volcanic plumes

NASA Astrophysics Data System (ADS)

Fiorani, Luca; Aiuppa, Alessandro; Angelini, Federico; Borelli, Rodolfo; Del Franco, Mario; Murra, Daniele; Pistilli, Marco; Puiu, Adriana; Santoro, Simone

2013-10-01

Accurate knowledge of gas composition in volcanic plumes has high scientific and societal value. On the one hand, it gives information on the geophysical processes taking place inside volcanos; on the other hand, it provides alert on possible eruptions. For this reasons, it has been suggested to monitor volcanic plumes by lidar. In particular, one of the aims of the FP7 ERC project BRIDGE is the measurement of CO2 concentration in volcanic gases by differential absorption lidar. This is a very challenging task due to the harsh environment, the narrowness and weakness of the CO2 absorption lines and the difficulty to procure a suitable laser source. This paper, after a review on remote sensing of volcanic plumes, reports on the current progress of the lidar system.

El Chichon - Composition of plume gases and particles

NASA Technical Reports Server (NTRS)

Kotra, J. P.; Finnegan, D. L.; Zoller, W. H.; Hart, M. A.; Moyers, J. L.

1983-01-01

Aircraft measurements were made of trace gases, atmospheric particles, and condensed acid volatiles in the plume of El Chichon volcano, Chiapas, Mexico, in November 1982. Hydrogen sulfide was the primary gaseous sulfur species in the plume at the time of collection. Concentrations of 28 elements were determined by neutron activation analysis of particulate material from the plume. The volatile elements sulfur, chlorine, arsenic, selenium, bromine, antimony, iodine, tungsten, and mercury were enriched relative to bulk pyroclastic material by factors of 60 to 20,000. Arsenic, antimony, and selenium were associated predominantly with small (not greater than 3 micrometer) particles. Calcium and sodium were present almost exclusively on larger particles and aluminum and manganese were bimodally distributed. Ashladen particulate material injected into the stratosphere during the early violent eruptions was enriched by factors of 10 to 30 relative to ash in some of the same elements observed in the quiescent plume.

Microbial gene functions enriched in the Deepwater Horizon deep-sea oil plume

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Z.; Deng, Y.; Nostrand, J.D. Van

2011-06-15

The Deepwater Horizon oil spill in the Gulf of Mexico is the deepest and largest offshore spill in U.S. history and its impacts on marine ecosystems are largely unknown. Here, we showed that the microbial community functional composition and structure were dramatically altered in a deep-sea oil plume resulting from the spill. A variety of metabolic genes involved in both aerobic and anaerobic hydrocarbon degradation were highly enriched in the plume compared to outside the plume, indicating a great potential for intrinsic bioremediation or natural attenuation in the deep-sea. Various other microbial functional genes relevant to carbon, nitrogen, phosphorus, sulfurmore » and iron cycling, metal resistance, and bacteriophage replication were also enriched in the plume. Together, these results suggest that the indigenous marine microbial communities could play a significant role in biodegradation of oil spills in deep-sea environments.« less

Compositional variation in aging volcanic plumes - Analysis of gaseous SO2, CO2 and halogen species in volcanic emissions using an Unmanned Aerial Vehicle (UAV).

NASA Astrophysics Data System (ADS)

Rüdiger, Julian; Lukas, Tirpitz; Bobrowski, Nicole; Gutmann, Alexandra; Liotta, Marcello; de Moor, Maarten; Hoffmann, Thorsten

2017-04-01

Volcanoes are a large source for several reactive atmospheric trace gases including sulfur and halogen containing species. The detailed understanding of volcanic plume chemistry is needed to draw information from gas measurements on subsurface processes. This knowledge is essential for using gas measurements as a monitoring tool for volcanic activity. The reactive bromine species bromine monoxide (BrO) is of particular interest, because BrO as well as SO2 are readily measurable from safe distance by spectroscopic remote sensing techniques. BrO is not directly emitted, but is formed in the plume by a multiphase reaction mechanism. The abundance of BrO changes as a function of the distance from the vent as well as the spatial position in the plume. The precursor substance for the formation of BrO is HBr with Br2as an intermediate product. In this study we present the application of a UAV as a carrier for a remote-controlled sampling system for halogen species (Br2, HBr, BrCl, etc), based on the gas diffusion denuder technique, which allows speciation and enrichment by selective organic reactions. For the analysis of gaseous SO2 and CO2 an in-situ gas monitoring system was additionally mounted. This setup was deployed into the gas plumes of Stromboli Volcano (Italy), Masaya Volcano (Nicaragua) and Turrialba Volcano (Costa Rica) in 2016, to investigate the halogen chemistry at distant locations in the plume further downwind to the emission source, which are in most cases not accessible by other approaches. Flights into the plume were conducted with ascents of up to 1000 m. From telemetrically transmitted SO2 mixing ratios, areas of dense plume where localized to keep the UAV stationary for up to 10 minutes of sampling time. Additionally, ground based samples were taken at the crater rim (at Masaya and Turrialba) using alkaline traps, denuder and gas sensors for comparison with airborne-collected data. Herein we will present time and spatial resolved gas mixing ratio data for SO2, CO2 and halogen species for crater rim sites and a downwind plume age of about 3 to 5 minutes.

Monitoring in situ biodegradation of benzene and toluene by stable carbon isotope fractionation.

PubMed

Vieth, Andrea; Kästner, Matthias; Schirmer, Mario; Weiss, Holger; Gödeke, Stefan; Meckenstock, Rainer U; Richnow, Hans H

2005-01-01

Intrinsic biodegradation of benzene and toluene in a heavily contaminated aquifer at the site of a former hydrogenation plant was investigated by means of isotope fractionation processes. The carbon isotope compositions of benzene and toluene were monitored in two campaigns within a time period of 12 months to assess the extent of the in situ biodegradation and the stability of the plume over time. The Rayleigh model, applied to calculate the extent of biodegradation and residual theoretical concentrations of toluene, showed that in situ biodegradation was a relevant attenuation process. The biodegradation rate constant for toluene was estimated to be k = 5.7+/-0.5 microM/d in the groundwater flow path downstream of the source area. The spatial distribution of the carbon isotope composition of benzene indicated that in situ biodegradation occurred at marginal zones of the plume where concentrations were lower than 30 mg/L. The vertical structure of the benzene plume provided evidence for in situ degradation processes at the upper and lower fringes of the plume. The results show that isotope fractionation can be used to quantify the extent of microbial in situ degradation in contaminated aquifers and to develop conceptual models for natural attenuation approaches.

Fast changes in chemical composition and size distribution of fine particles during the near-field transport of industrial plumes.

PubMed

Marris, Hélène; Deboudt, Karine; Augustin, Patrick; Flament, Pascal; Blond, François; Fiani, Emmanuel; Fourmentin, Marc; Delbarre, Hervé

2012-06-15

Aerosol sampling was performed inside the chimneys and in the close environment of a FeMn alloys manufacturing plant. The number size distributions show a higher abundance of ultrafine aerosols (10-100 nm) inside the plume than upwind of the plant, indicating the emissions of nanoparticles by the industrial process. Individual analysis of particles collected inside the plume shows a high proportion of metal bearing particles (Mn-/Fe-) consisting essentially of internally mixed aluminosilicate and metallic compounds. These particles evolve rapidly (in a few minutes) after emission by adsorption of VOC gas and sulfuric acid emitted by the plant but also by agglomeration with pre-existing particles. At the moment, municipalities require a monitoring of industrial emissions inside the chimneys from manufacturers. However those measures are insufficient to report such rapid changes in chemical composition and thus to evaluate the real impact of industrial plumes in the close environment of plants (when those particles leave the industrial site). Consequently, environmental authorities will have to consider such fast evolutions and then to adapt future regulations on air pollution sources. Copyright © 2012 Elsevier B.V. All rights reserved.

Space Shuttle Plume and Plume Impingement Study

NASA Technical Reports Server (NTRS)

Tevepaugh, J. A.; Penny, M. M.

1977-01-01

The extent of the influence of the propulsion system exhaust plumes on the vehicle performance and control characteristics is a complex function of vehicle geometry, propulsion system geometry, engine operating conditions and vehicle flight trajectory were investigated. Analytical support of the plume technology test program was directed at the two latter problem areas: (1) definition of the full-scale exhaust plume characteristics, (2) application of appropriate similarity parameters; and (3) analysis of wind tunnel test data. Verification of the two-phase plume and plume impingement models was directed toward the definition of the full-scale exhaust plume characteristics and the separation motor impingement problem.

Cutting through the smoke: the diversity of microorganisms in deep-sea hydrothermal plumes.

PubMed

Djurhuus, Anni; Mikalsen, Svein-Ole; Giebel, Helge-Ansgar; Rogers, Alex D

2017-04-01

There are still notable gaps regarding the detailed distribution of microorganisms between and within insular habitats such as deep-sea hydrothermal vents. This study investigates the community composition of black smoker vent microorganisms in the Southern Hemisphere, and changes thereof along a spatial and chemical gradient ranging from the vent plume to surrounding waters. We sampled two hydrothermal vent fields, one at the South West Indian Ridge (SWIR), the other at the East Scotia Ridge (ESR). Samples were collected across vent fields at varying vertical distances from the origin of the plumes. The microbial data were sequenced on an Illumina MiSeq platform for the 16SrRNA gene. A substantial amount of vent-specific putative chemosynthetic microorganisms were found, particularly in samples from focused hydrothermal venting. Common vent-specific organisms from both vent fields were the genera Arcobacter , Caminibacter and Sulfurimonas from the Epsilonproteobacteria and the SUP05 group from the Gammaproteobacteria. There were no major differences in microbial composition between SWIR and ESR for focused plume samples. However, within the ESR the diffuse flow and focused samples differed significantly in microbial community composition and relative abundance. For Epsilonproteobacteria, we found evidence of niche-specificity to hydrothermal vent environments. This taxon decreased in abundance by three orders of magnitude from the vent orifice to background water. Epsilonproteobacteria distribution followed a distance-decay relationship as vent-effluents mixed with the surrounding seawater. This study demonstrates strong habitat affinity of vent microorganisms on a metre scale with distinct environmental selection.

Guided Seismic Waves: Possible Diagnostics for Hot Plumes in the Mantle

NASA Astrophysics Data System (ADS)

Evans, J. R.; Julian, B. R.; Foulger, G. R.

2005-12-01

Seismic waves potentially provide by far the highest resolution view of the three-dimensional structure of the mantle, and the hope of detecting wave-speed anomalies caused by hot or compositionally buoyant mantle plumes has been a major incentive to the development of tomographic seismic techniques. Seismic tomography is limited, however, by the uneven geographical distribution of earthquakes and seismometers, which can produce artificial tomographic wave-speed anomalies that are difficult to distinguish from real structures in the mantle. An alternate approach may be possible, because hot plumes and possibly some compositional upwellings would have low seismic-wave speeds and would act as efficient waveguides over great depth ranges in the mantle. Plume-guided waves would be little affected by bends or other geometric complexities in the waveguides (analogously to French horns and fiber-optic cables), and their dispersion would make them distinctive on seismograms and would provide information on the size and structure of the waveguide. The main unanswered question is whether guided waves in plumes could be excited sufficiently to be observable. Earthquakes do not occur in the deep mantle, but at least two other possible sources of excitation can be imagined: (1) shallow earthquakes at or near plume-fed hotspots; and (2) coupling of plume-guided waves to seismic body waves near the bottom of the mantle. In the first case, downward-traveling guided waves transformed to seismic body waves at the bottom of the waveguide would have to be detected at teleseismic distances. In the second case, upward-traveling guided waves generated by teleseismic body waves would be detected on seismometers at hotspots. Qualitative reasoning based on considerations of reciprocity suggests that the signals in these two situations should be similar in size and appearance. The focusing of seismic core phases at caustics would amplify plume waves excited by either mechanism (1) or (2) at particular epicentral distances. A failure to find such guided waves experimentally could mean either that the waveguides (plumes) do not exist or that the excitation mechanisms and/or seismometer networks are inadequate. Distinguishing these two possibilities would require careful analysis. Anticipated major improvements in seismic instrumentation, such as the EarthScope initiative, make this a propitious time to undertake a search for plume-guided waves in the mantle.

Tvashtar Composite

NASA Image and Video Library

2007-05-01

Variations in the appearance of the giant plume from the Tvashtar volcano on Jupiter moon Io are seen in this composite of the best photos taken by the New Horizons Long Range Reconnaissance Imager LORRI during its Jupiter flyby in late February.

Plume composition as observed by the Cassini Ion Neutral Mass Spectrometer

NASA Astrophysics Data System (ADS)

Waite, J. Hunter; Magee, Brian; Yelle, Roger; Cravens, Tom; Luhmann, Janet; McNutt, Ralph; Kasprzak, Wayne; Niemann, Hasso

The gaseous composition as measured by the Cassini Ion Neutral Mass Spectrometer has been used to infer a plume composition composed mainly of water vapor with percentage amounts of carbon dioxide, ammonia, carbon dioxide and/or molecular nitrogen, and smaller amounts of methane, a combination of acetylene, hydrogen cyanide, and ethylene, propene, argon, and other trace organics (benzene, methanol, formaldehyde, etc). High signal to noise values on the fifth Cassini flyby of Enceladus allowed the determination of a D/H ratio in water of 2.9 x 10-4 similar to values observed in Oort cloud comets to date and suggesting some similarities in conditions during formation. The high value of 40 Ar inferred suggests liquid processes in the interior. Earlier measurements and later measurements present some indication of changes in composition with time or encounter conditions that will be emphasized in this presentation.

Trace element evidence for a depleted component intrinsic to the Hawaiian plume

NASA Astrophysics Data System (ADS)

DeFelice, C.; Mallick, S.; Saal, A. E.; Huang, S.

2017-12-01

The Hawaii Scientific Drilling Project (HSDP) recovered 3.5 km of Mauna Kea post-shield and shield stage basalts to investigate the geochemical evolution of a Hawaiian shield stage volcano and to constrain the geochemical structure of Hawaiian plume. A group of tholeiitic lavas from 1760-1810 meters below sea level (mbsl) have higher CaO content at given MgO content and are called high-CaO basalts. Isotopes of Pb, Sr, Hf, and Nd of these basalts show they are the most depleted shield basalts ever recovered in Hawaii. Their 206Pb/204Pb-208Pb/204Pb values indicate that they are not related to Pacific MORB. Their Ba/Th values (115-160) are characteristic of Hawaiian plume material and they are isotopically similar to Hawaiian rejuvenated stage lavas. To further investigate this relationship, we compare high-CaO basalts to the Honolulu Volcanics, a set of rejuvenated stage lavas. To determine their possible petrogenetic relation, we calculate their parental melt composition by adding or removing olivine until their geochemical composition is in equilibrium with Fo90. The High-CaO basalt parent magma composition has a much flatter REE pattern and much lower absolute REE contents than that of the Honolulu lavas. Batch melting forward models are calculated to determine potential sources that could contribute to both the Honolulu Volcanics and high-CaO basalts petrogenesis. Both parental magma compositions can be recreated by melting the same rejuvenated-stage source composition to varying degrees. Honolulu Volcanics are the result of a low degree of melting of the rejuvenated source, while higher degrees of melting reproduce the high-CaO basalts. The High-CaO basalts, erupted during shield-stage volcanism, show that the depleted component that rejuvenated stage basalts form from can be sampled during the most voluminous stage of volcanism, and is likely intrinsic to the plume.

Dynamic estuarine plumes and fronts: importance to small fish and plankton in coastal waters of NSW, Australia

NASA Astrophysics Data System (ADS)

Kingsford, M. J.; Suthers, I. M.

1994-05-01

In 1990, low density estuarine plumes in the vicinity of Botany Bay, Australia, extended up to 11 km across a narrow continental shelf ( ca 25 km) on ebb tides. The shape and seaward extent of plumes varied according to a combination of state of the tide, freshwater input and the direction and intensity of coastal currents. Offshore plumes dissipated on the flood tide and fronts reformed at the entrance of Botany Bay. Major differences in the abundance and composition of ichthyoplankton and other zooplankton were found over a 400-800 m stretch of water encompassing waters of the plume, front and ocean on seven occasions. For example, highest abundances of the fishes Gobiidae, Sillaginidae, Gerreidae and Sparidae as well as barnacle larvae and fish eggs were found in plumes. Cross-shelf distribution patterns of zooplankton, therefore, are influenced by plumes. Distinct assemblages of plankters accumulated in fronts, e.g. fishes of the Mugilidae and Gonorynchidae and other zooplankters (e.g. Jaxea sp.). Accumulation in fronts was variable and may relate to variable convergence according to the tide. We argue that plumes provide a significant cue to larvae in coastal waters that an estuary is nearby. Moreover, although many larvae may be retained in the turbid waters of plumes associated with riverine input, larvae are potentially exported in surface waters on ebb tides.

Origin of silicic crust by rifting and bimodal plume volcanism in the Afar Depression

NASA Astrophysics Data System (ADS)

Ghatak, A.; Basu, A. R.; Ebinger, C. J.

2010-12-01

The youngest mantle plume province worldwide occurs at the seismically and volcanically active East African - Red Sea - Gulf of Aden (Afar) triple junction, where one or more upwellings has impinged the thick cratonic lithosphere since ~45 Ma. A spectacular example of magmatism in the Afar depression is seen in the present to < 2 Ma old bimodal fissural mafic and peralkaline silicic eruptions in the ~60 km-long Dabbahu-Manda Hararo (DMH) Rift. In this study we report major, trace elements, and Nd-Sr-Pb isotopes in recent basaltic and silicic rocks originating from the center of the DMH rift segment, exposed along the rift axis and flanks of this segment. The rare earth element (REE) patterns of the silicic rocks and basalts are different in two significant ways: (1) the silicic rocks show a prominent positive Ce-anomaly that is extremely rare in volcanic rocks; and (2) this positive Ce-anomaly is accompanied by a strong negative Eu-anomaly. These anomalies are absent in the basaltic rocks. The positive Ce-anomaly is probably due to interaction in a magma chamber, similar in composition to the basalts, with deep saline aquifer or brines that typically show positive Ce-anomaly. The REE patterns of the two lava groups are interpreted to be due to fractional crystallization of plagioclase in a magma chamber similar in REE composition as the basalts that erupted in the DMH segments. We interpret the silicic rocks to be residues after ~20% fractional crystallization of plagioclase in the DMH basalts. The Nd-Pb isotopic composition of the basalts and rhyolites of the DMH are similar to the Ethiopian plume as defined by the ~30 Ma old Ethiopian flood basalts. Based on their high 3He/4He ratios (R/RA ~30) and Nd-Sr-Pb isotopic data, the source of the Ethiopian plume is generally believed to be in the lower mantle. Therefore, the similarity of the Nd-Pb and Pb-Pb isotopic variations between the Ethiopian plume and the DMH lavas indicates that these lavas were sourced from the lower mantle, and this source zone showed little variation over the past 30 Ma. Some of the silicic lavas fall distinctly outside the plume field toward more radiogenic 87Sr/86Sr at relatively restricted Nd and Pb isotopic compositions. This excursion in Sr-isotopic ratios of the silicic lavas, in concert with their positive Ce-anomaly, is interpreted to be due to mixing of the Afar plume derived basaltic magma with fluids from saline aquifers. We conclude that the bimodal lavas are consanguineous, the silicic lavas being generated by fractional crystallization of plagioclase in a lower mantle plume-derived basaltic magma-chamber, caused by the interaction with saline aquifers. The generation of bimodal volcanism from parental primitive basalts without any contribution from pre-existing continental crust in Dabbahu may explain other similar intraplate magmatism including early Archean-Hadean continental crust formation prior to onset of arc-volcanism.

Comprehensive simultaneous shipboard and airborne characterization of exhaust from a modern container ship at sea.

PubMed

Murphy, Shane M; Agrawal, Harshit; Sorooshian, Armin; Padró, Luz T; Gates, Harmony; Hersey, Scott; Welch, W A; Lung, H; Miller, J W; Cocker, David R; Nenes, Athanasios; Jonsson, Haflidi H; Flagan, Richard C; Seinfeld, John H

2009-07-01

We report the first joint shipboard and airborne study focused on the chemical composition and water-uptake behavior of particulate ship emissions. The study focuses on emissions from the main propulsion engine of a Post-Panamax class container ship cruising off the central coast of California and burning heavy fuel oil. Shipboard sampling included micro-orifice uniform deposit impactors (MOUDI) with subsequent off-line analysis, whereas airborne measurements involved a number of real-time analyzers to characterize the plume aerosol, aged from a few seconds to over an hour. The mass ratio of particulate organic carbon to sulfate at the base of the ship stack was 0.23 +/- 0.03, and increased to 0.30 +/- 0.01 in the airborne exhaust plume, with the additional organic mass in the airborne plume being concentrated largely in particles below 100 nm in diameter. The organic to sulfate mass ratio in the exhaust aerosol remained constant during the first hour of plume dilution into the marine boundary layer. The mass spectrum of the organic fraction of the exhaust aerosol strongly resembles that of emissions from other diesel sources and appears to be predominantly hydrocarbon-like organic (HOA) material. Background aerosol which, based on air mass back trajectories, probably consisted of aged ship emissions and marine aerosol, contained a lower organic mass fraction than the fresh plume and had a much more oxidized organic component. A volume-weighted mixing rule is able to accurately predict hygroscopic growth factors in the background aerosol but measured and calculated growth factors do not agree for aerosols in the ship exhaust plume. Calculated CCN concentrations, at supersaturations ranging from 0.1 to 0.33%, agree well with measurements in the ship-exhaust plume. Using size-resolved chemical composition instead of bulk submicrometer composition has little effect on the predicted CCN concentrations because the cutoff diameter for CCN activation is larger than the diameter where the mass fraction of organic aerosol begins to increase significantly. The particle number emission factor estimated from this study is 1.3 x 10(16) (kg fuel)(-1), with less than 1/10 of the particles having diameters above 100 nm; 24% of particles (>10 nm in diameter) activate into cloud droplets at 0.3% supersaturation.

The effects of solid rocket motor effluents on selected surfaces and solid particle size, distribution, and composition for simulated shuttle booster separation motors

NASA Technical Reports Server (NTRS)

Jex, D. W.; Linton, R. C.; Russell, W. M.; Trenkle, J. J.; Wilkes, D. R.

1976-01-01

A series of three tests was conducted using solid rocket propellants to determine the effects a solid rocket plume would have on thermal protective surfaces (TPS). The surfaces tested were those which are baselined for the shuttle vehicle. The propellants used were to simulate the separation solid rocket motors (SSRM) that separate the solid rocket boosters (SRB) from the shuttle launch vehicle. Data cover: (1) the optical effects of the plume environment on spacecraft related surfaces, and (2) the solid particle size, distribution, and composition at TPS sample locations.

Further Analysis on the Mystery of the Surveyor III Dust Deposits

NASA Technical Reports Server (NTRS)

Metzger, Philip; Hintze, Paul; Trigwell, Steven; Lane, John

2012-01-01

The Apollo 12 lunar module (LM) landing near the Surveyor III spacecraft at the end of 1969 has remained the primary experimental verification of the predicted physics of plume ejecta effects from a rocket engine interacting with the surface of the moon. This was made possible by the return of the Surveyor III camera housing by the Apollo 12 astronauts, allowing detailed analysis of the composition of dust deposited by the LM plume. It was soon realized after the initial analysis of the camera housing that the LM plume tended to remove more dust than it had deposited. In the present study, coupons from the camera housing have been reexamined. In addition, plume effects recorded in landing videos from each Apollo mission have been studied for possible clues.

Noble gas composition of Indian carbonatites (Amba Dongar, Siriwasan): Implications on mantle source compositions and late-stage hydrothermal processes

NASA Astrophysics Data System (ADS)

Hopp, Jens; Viladkar, Shrinivas G.

2018-06-01

Within a stepwise crushing study we determined the noble gas composition of several calcite separates, one aegirine and one pyrochlore-aegirine separate of the carbonatite ring dyke complex of Amba Dongar and carbonatite sill complex of Siriwasan, India. Both carbonatites are related to the waning stages of volcanic activity of the Deccan Igneous Province ca. 65 Ma ago. Major observations are a clear radiogenic 4He* and nucleogenic 21Ne* imprint related to in situ production from U and Th in mineral impurities, most likely minute apatite grains, or late incorporation of crustal fluids. However, in first crushing steps of most calcites from Amba Dongar a well-resolvable mantle neon signal is observed, with lowest air-corrected mantle 21Ne/22Ne-compositions equivalent to the Réunion hotspot mantle source. In case of the aegirine separate from Siriwasan we found a neon composition similar to the Loihi hotspot mantle source. This transition from a mantle plume signal in first crushing step to a more nucleogenic signature with progressive crushing indicates the presence of an external (crustal) or in situ nucleogenic component unrelated and superposed to the initial mantle neon component whose composition is best approximated by results of first crushing step(s). This contradicts previous models of a lithospheric mantle source of the carbonatitic magmas from Amba Dongar containing recycled crustal components which base on nucleogenic neon compositions. Instead, the mantle source of both investigated carbonatite complexes is related to a primitive mantle plume source that we tentatively ascribe to the postulated Deccan mantle plume. If, as is commonly suggested, the present location of the Deccan mantle plume source is below Réunion Island, the currently observed more nucleogenic neon isotopic composition of the Réunion hotspot might be obliterated by significant upper mantle contributions. In addition, compared with other carbonatite complexes worldwide a rather significant contribution of atmospheric noble gases is observed. This is documented in cut-off 20Ne/22Ne-ratios of ca. 10.2 (Amba Dongar) and 10.45 (Siriwasan) and cut-off 40Ar/36Ar-ratios of about 1500. This atmospheric component had been added at shallow levels during the emplacement process or later during hydrothermal alteration. However, understanding the late-stage interaction between atmospheric gases and magmatic mantle fluids still requires further investigation.

Life and Death of a Flood Basalt: Evolution of a Magma Plumbing System in the Ethiopian Low-Ti Flood Basalt Province

NASA Astrophysics Data System (ADS)

Krans, S. R.; Rooney, T. O.; Kappelman, J. W.; Yirgu, G.; Ayalew, D.

2017-12-01

Continental flood basalt provinces (CFBPs), which are thought to preserve the magmatic record of an impinging mantle plume head, offer spatial and temporal insight into melt generation processes in Large Igneous Provinces (LIPs). Despite the utility of CFBPs in probing the composition of mantle plumes, these basalts typically erupt fractionated compositions, suggestive of significant residence time in the continental lithosphere. The location and duration of this residence within the continental lithosphere provides additional insights into the flux of plume-related magmas. The NW Ethiopian plateau offers a well preserved stratigraphic section from flood basalt initiation to termination, and is thus an important target for study of CFBPs. We examine petrographic and whole rock geochemical variation within a stratigraphic framework and place these observations within the context of the magmatic evolution of the Ethiopian CFBP. We observe multiple pulses of magma recharge punctuated by brief shut-down events and an overall shallowing of the magmatic plumbing system over time. Initial flows are fed by magmas that have experienced deeper fractionation (clinopyroxene dominated and lower CaO/Al2O3 for a given MgO value), likely near the crust-mantle boundary. Subsequent flows are fed by magmas that have experienced shallower fractionation (plagioclase dominated and higher CaO/Al2O3 for a given MgO value) in addition to deeper fractionated magmas. Broad changes in flow thickness and modal mineralogy are consistent with fluctuating changes in magmatic flux through a complex plumbing system and indicate pulsed magma flux and an overall shallowing of the magmatic plumbing system over time. Pulses of less differentiated magmas (MgO > 8 wt%) and high-An composition of plagioclase megacrysts (labradorite to bytownite) suggest a constant replenishing of new primitive magma recharging the shallow plumbing system during the main phase of flood volcanism, though the magnitude of flux changes, reaching an apex prior to flood basalt termination. The origin of these pulses remains enigmatic and may relate to heterogeneities in plume composition, upwelling rate, or mantle potential temperature. The results of this study provide first order modeling constraints for future modeling of plume-lithosphere interactions.

Infrared signature modelling of a rocket jet plume - comparison with flight measurements

NASA Astrophysics Data System (ADS)

Rialland, V.; Guy, A.; Gueyffier, D.; Perez, P.; Roblin, A.; Smithson, T.

2016-01-01

The infrared signature modelling of rocket plumes is a challenging problem involving rocket geometry, propellant composition, combustion modelling, trajectory calculations, fluid mechanics, atmosphere modelling, calculation of gas and particles radiative properties and of radiative transfer through the atmosphere. This paper presents ONERA simulation tools chained together to achieve infrared signature prediction, and the comparison of the estimated and measured signatures of an in-flight rocket plume. We consider the case of a solid rocket motor with aluminized propellant, the Black Brant sounding rocket. The calculation case reproduces the conditions of an experimental rocket launch, performed at White Sands in 1997, for which we obtained high quality infrared signature data sets from DRDC Valcartier. The jet plume is calculated using an in-house CFD software called CEDRE. The plume infrared signature is then computed on the spectral interval 1900-5000 cm-1 with a step of 5 cm-1. The models and their hypotheses are presented and discussed. Then the resulting plume properties, radiance and spectra are detailed. Finally, the estimated infrared signature is compared with the spectral imaging measurements. The discrepancies are analyzed and discussed.

Istopically Defined Source Reservoirs of Primitive Magmas in the East African Rift.

NASA Astrophysics Data System (ADS)

Rooney, T. O.; Furman, T.; Hanan, B.

2005-12-01

Extension within the East African Rift is a function of the interaction between plume-driven uplift and far-field stresses associated with plate tectonic processes. Geochemical and isotopic investigation of primitive basalts from the Main Ethiopian Rift (MER) reveals systematic spatial variations in the contributions from distinct and identifiable source reservoirs that, in turn help identify the mechanisms by which along-axis rifting has progressed. The Sr-Nd-Pb isotopic characteristics of MER basalts can be described by a three-component mixing model involving the long-lived Afar plume, a depleted mantle component similar to the source region for Gulf of Aden MORB from east of 48° E and a reservoir that is likely lithospheric (sub-continental mantle lithosphere, magmatic underplate or lower crust). Quaternary basalts in the central MER exhibit a systematic decrease in plume influence southward from 9.5° N to 8° N, i.e., away from the modern surface expression of the Afar plume in Djibouti and Erta 'Ale. The composition of the Afar plume component is comparable to the "C" mantle reservoir. This southward decrease in plume influence is coupled with an increase in the influence of the lithospheric and depleted mantle components. Linear arrays observed within Pb-Pb isotopic space at each eruptive center require distinctive ratio of lithospheric + depleted mantle components mixing with variable amounts of the "C"-like plume component. This isotopic evidence suggests the depleted mantle and lithosphere mixed prior to the generation of the recent magmas. To the south, the Sr-Nd-Pb isotopic compositions of Turkana (Kenya) rift basalts record a mix of a similar "C"-like plume component and a fourth HIMU-like source component. Low 3He/4He values observed in the HIMU-dominated lavas from Turkana contrast with the higher ratios found in basalts associated with the "C"-like Afar plume. Further analysis of "C"-HIMU lavas at Turkana is required to fully constrain the He isotopic signatures. Thus, along-axis patterns in Quaternary EARS magmatism are compatible with two "C"-like plumes with contributions from the upper mantle and chemically distinct lithospheric components. Alternatively, a single "C"-like plume can account for these relationships. In the single plume scenario, the HIMU source component present in the 30 Ma Turkana lavas may represent melting of metasomatised lithosphere, derived from the accretion of island-arc-backarc basins during Pan-African events (e.g. Schilling et al., 1992). The recent plume-dominated activity in Turkana and Afar are separated by a region characterized by waning plume influence and a greater contribution from the depleted mantle. This intermediate zone, which is located in the south-central MER represents the modern site of contact between the northward propagating Kenya / Turkana Rift and the southward propagating Afar Rift zone.

Chemical and Microphysical Properties of Particles in Aged Forest Fire Plumes From Alaska and Western Canada Observed Over the Northeastern U.S.

NASA Astrophysics Data System (ADS)

Brock, C. A.; Wollny, A. G.; Cooper, O. R.; Fehsenfeld, F. C.; de Gouw, J. A.; Hudson, P. K.; Matthew, B. M.; Middlebrook, A. M.; Murphy, D. M.; Simsons, C.; Stohl, A.; Warneke, C.; Peltier, R.; Sulivan, A.; Weber, R. J.; Wilson, J. C.

2004-12-01

During the Intercontinental Transport and Chemical Transformation - New England Air Quality Study (ITCT-NEAQS 2004) in July and August 2004 several forest fires plumes were observed over the northeastern U.S. and southeastern Canada. Satellite data and trajectory analyses indicate that the plumes originated from forest fires burning in Alaska and western Canada. In-situ measurements of the aged forest fire smoke were made on board the NOAA WP-3D research aircraft during several flights over a period of 2 weeks. Concentrations of volatile organic compounds (VOCs) and the chemical composition of single aerosol particles in air masses containing forest fire smoke show significant differences compared to background air or to pollution from urban and industrial sources and unambiguously identify the smoke plumes. Particle size distributions from 0.004 to 8 um were measured with one second resolution in the aged forest fire smoke. The smoke was characterized by mass-weighted diameters between 0.6 and 1 um--much larger than secondary particles typical of urban and industrial sources. Particle volume concentrations were among the highest seen within the ITCT-NEAQS 2004 project, and regional visibility and air quality were significantly affected by the transported smoke. Quantitative compositional measurements were made of the non-refractory fraction of submicron particles, as well as of submicron inorganic ionic compounds and water soluble organic mass, within the forest fire plumes. The submicron aerosol particles in the biomass plumes were largely carbonaceous with very little sulfate, ammonium, or nitrate. A fraction of this carbonaceous material was soluble in water and likely contained oxygenated organic species.

Composition of the excimer laser-induced plume produced during LASIK refractive surgery

NASA Astrophysics Data System (ADS)

Glickman, Randolph D.; Liu, Yun; Mayo, George L.; Baribeau, Alan D.; Starck, Tomy; Bankhead, Tom

2003-07-01

Because of concerns about potential hazards to surgical personnel of the plume associated with laser refractive surgery, this study was performed to characterize the composition of such plumes. Filter elements were removed from the smoke evacuator of a VISX S3 excimer laser (filter pore size ~0.3 microns) and from a Mastel Clean Room ( filter pore size ~0.2 microns) used with a LADARVISION excimer laser. The filters from both laser systems captured the laser-induced plumes from multiple, routine, LASIK patient procedures. Some filters were processed for scanning electron microscopy, while others were extracted with methanol and chloroform for biochemical analysis. Both the VISX "Final Air" filter and the Mastel "Clean Room" filter captured material that was not observed in filters that had clean operating room air only passed through them. In the VISX system, air flows through the filter unit parallel to the filter matrix. SEM analysis showed these filters captured discrete particles of 0.3 to 3.0 microns in size. In the Mastel Clean Room unit, air flows orthogonally through the filter, and the filter matrix was heavily layered with captured debris so that individual particles were not readily distinguished. Amino acid analysis and gel electrophoresis of extracted material revealed proteinaceous molecules as large as 5000 molecular weight. Such large molecules in the laser plume are not predicted by the existing theory of photochemical ablation. The presence of relatively large biomolecules may constitute a risk of allergenic reactions in personnel exposed to the plume, and also calls into question the precise mechanism of excimer laser photochemical ablation. Supported by the RMG Research Endowment, and Research to Prevent Blindness

Simulation of Deepwater Horizon oil plume reveals substrate specialization within a complex community of hydrocarbon degraders

DOE PAGES

Hu, Ping; Dubinsky, Eric A.; Probst, Alexander J.; ...

2017-06-26

The Deepwater Horizon (DWH) accident released an estimated 4.1 million barrels of oil and 10 10 mol of natural gas into the Gulf of Mexico, forming deep-sea plumes of dispersed oil droplets and dissolved gases that were largely degraded by bacteria. During the course of this 3-mo disaster a series of different bacterial taxa were enriched in succession within deep plumes, but the metabolic capabilities of the different populations that controlled degradation rates of crude oil components are poorly understood. We experimentally reproduced dispersed plumes of fine oil droplets in Gulf of Mexico seawater and successfully replicated the enrichment andmore » succession of the principal oil-degrading bacteria observed during the DWH event. We recovered near-complete genomes, whose phylogeny matched those of the principal biodegrading taxa observed in the field, including the DWH Oceanospirillales (now identified as a Bermanella species), multiple species of Colwellia, Cycloclasticus, and other members of Gammaproteobacteria, Flavobacteria, and Rhodobacteria. Metabolic pathway analysis, combined with hydrocarbon compositional analysis and species abundance data, revealed substrate specialization that explained the successional pattern of oil-degrading bacteria. The fastest-growing bacteria used short-chain alkanes. The analyses also uncovered potential cooperative and competitive relationships, even among close relatives. We conclude that patterns of microbial succession following deep ocean hydrocarbon blowouts are predictable and primarily driven by the availability of liquid petroleum hydrocarbons rather than natural gases.« less

Simulation of Deepwater Horizon oil plume reveals substrate specialization within a complex community of hydrocarbon degraders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Ping; Dubinsky, Eric A.; Probst, Alexander J.

The Deepwater Horizon (DWH) accident released an estimated 4.1 million barrels of oil and 10 10 mol of natural gas into the Gulf of Mexico, forming deep-sea plumes of dispersed oil droplets and dissolved gases that were largely degraded by bacteria. During the course of this 3-mo disaster a series of different bacterial taxa were enriched in succession within deep plumes, but the metabolic capabilities of the different populations that controlled degradation rates of crude oil components are poorly understood. We experimentally reproduced dispersed plumes of fine oil droplets in Gulf of Mexico seawater and successfully replicated the enrichment andmore » succession of the principal oil-degrading bacteria observed during the DWH event. We recovered near-complete genomes, whose phylogeny matched those of the principal biodegrading taxa observed in the field, including the DWH Oceanospirillales (now identified as a Bermanella species), multiple species of Colwellia, Cycloclasticus, and other members of Gammaproteobacteria, Flavobacteria, and Rhodobacteria. Metabolic pathway analysis, combined with hydrocarbon compositional analysis and species abundance data, revealed substrate specialization that explained the successional pattern of oil-degrading bacteria. The fastest-growing bacteria used short-chain alkanes. The analyses also uncovered potential cooperative and competitive relationships, even among close relatives. We conclude that patterns of microbial succession following deep ocean hydrocarbon blowouts are predictable and primarily driven by the availability of liquid petroleum hydrocarbons rather than natural gases.« less

Transition From Archean Plume-Arc Orogens to Phanerozoic Style Convergent Margin Orogens, and Changing Mantle Lithosphere

NASA Astrophysics Data System (ADS)

Kerrich, R.; Jia, Y.; Wyman, D.

2001-12-01

Mantle plume activity was more intense in the Archean and komatiite-basalt volcanic sequences are a major component of many Archean greenstone belts. Tholeiitic basalts compositionally resemble Phanerozoic and Recent ocean plateau basalts, such as those of Ontong Java and Iceland. However, komatiite-basalt sequences are tectonically imbricated with bimodal arc lavas and associated trench turbidites. Interfingering of komatiite flows with boninite series flows, and primitive to evolved arc basalts has recently been identified in the 2.7 Ga Abitibi greenstone belt, demonstrating spatially and temporally associated plume and arc magmatism. These observations are consistent with an intra-oceanic arc migrating and capturing an ocean plateau, where the plateau jams the arc and imbricated plateau-arc crust forms a greenstone belt orogen. Melting of shallowly subducted plateau basalt crust (high Ba, Th, LREE) accounts for the areally extensive and voluminous syntectonic tonalite batholiths. In contrast, the adakite-Mg-andesite-Niobium enriched basalt association found in Archean greenstone belts and Cenozoic arcs are melts of LREE depleted MORB slab. Buoyant residue from anomalously hot mantle plume melting at > 100km rises to couple with the composite plume-arc crust to form the distinctively thick and refractory Archean continental lithospheric mantle. New geochemical data for structurally hosted ultramafic units along the N. American Cordillera, from S. California to the Yukon, show that these are obducted slices of sub-arc lithospheric mantle. Negatively fractionated HREE with high Al2O3/TiO2 ratios signify prior melt extraction, and variably enriched Th and LREE with negative Nb anomalies a subduction component in a convergent margin. A secular decrease of mantle plume activity and temperature results in plume-arc dominated geodynamics in the Archean with shallow subduction and thick CLM, whereas Phanerozoic convergent margins are dominated by arc-continent, arc-terrane, and terrane-terrane collision with steep subduction resulting in narrow belts of granitoids and obduction of lithospheric mantle.

Anthropogenic plumes from metropolitan areas and biomass burning emissions in West Africa during DACCIWA - airborne measurements on board the DLR Falcon 20

NASA Astrophysics Data System (ADS)

Stratmann, Greta; Schlager, Hans; Sauer, Daniel; Brocchi, Vanessa; Catoire, Valery; Baumann, Robert

2017-04-01

The DACCIWA (Dynamics-Aerosol-Chemistry-Cloud Interactions over West Africa) airborne field campaign was conducted in Southern West Africa in June/July 2016. Three European research aircraft (DLR - Falcon 20, SAFIRE - ATR 42 and BAS - Twin Otter) were deployed from Lomé/Togo and conducted research flights across Ivory Coast, Ghana, Togo and Benin. On board the DLR Falcon O3, SO2, CO, NO2 and aerosol fine mode particle number concentration and size distribution were measured during a total of 12 scientific flights. Until now only few airborne trace gas measurements were conducted in Southern West Africa. Therefore, this field experiment contributes to the knowledge of the chemical composition of the lower troposphere between 0 - 4 km. During several flights pollution plumes from major population centers - Lomé/Togo, Accra/Ghana, Kumasi/Ghana, and Abidjan/Ivory Coast - were probed below, inside and above clouds. Here, enhanced trace gas and particle concentrations were observed. In addition, plumes from biomass burning emissions were detected which were transported to West Africa. The composition of the pollution plumes are presented as well as transport pathways using HYSPLIT (Hybrid Single-Particle Lagrangian Integrated Trajectories) trajectory calculations. Ozone enhancements in the biomass burning pollution plumes of up to 70 ppb were observed compared to background concentrations of 30-40 ppb. Furthermore, HYSPLIT atmospheric dispersion simulations are used to estimate anthropogenic SO2 city emissions.

Biomass Burning Influences on the Composition of the Remote South Pacific Troposphere: Analysis Based on Observations from PEM Tropics-A

NASA Technical Reports Server (NTRS)

Singh, H. B.; Viezee, W.; Chen, Y.; Bradshaw, J.; Sandholm, S.; Blake, D.; Blake, N.; Heikes, B.; Snow, J.; Talbot, R.;

Alkaline lavas from southern Mendoza, Argentina, extend the Patagonian DUPAL mantle field to the north

NASA Astrophysics Data System (ADS)

Soager, N.; Holm, P. M.; Llambias, E.

2010-12-01

The lavas sampled around Río Colorado ~37°S at the border of Mendoza and Neuquén provinces, Argentina, define an OIB-like end-member composition for the Pleistocene and Holocene activity in the Payún Matrú volcanic field. Although positioned in the far back-arc of the Andes, only a few lavas show signs of involvement of slab fluids or crustal contamination such as relatively high LILEs relative to Nb. The very low La/Nb (~0.66) and Zr/Nb (~5) and high U/Pb (0.3-0.4) of the end-member composition clearly distinguish the source from normal MORB mantle, while high Ba/Nb (~10) and K/Nb (370-400) compared to FOZO and HIMU type OIBs suggest an EM type of mantle. Overall, the trace element patterns of the Río Colorado lavas are similar to the central and north Patagonian intraplate basalts and to South Atlantic E-MORB affected by the Discovery plume and the LOMU component (le Roux et al., 2002, EPSL 203). The isotopic composition of the Río Colorado component has a 206Pb/204Pb = 18.4, 207Pb/204Pb = 15.58, 208Pb/204Pb = 38.3, 87Sr/86Sr = 0.70353 and 143Nd/144Nd = 0.51285. This composition overlaps the central and north Patagonian intraplate basalts in Pb-isotopic space but is slightly less enriched in Sr and Nd-isotopes. It is distinctly different from the FOZO like composition of the south Patagonian intraplate basalts and the nearby Juan Fernandéz plume but similar to the South Atlantic N-MORB and MORB from the southern Chile Ridge segment 4 (Sturm et al., 1999, JGR 104) described as DUPAL type. The DUPAL-MORB type isotopic composition and the plume-like trace element patterns of the Río Colorado lavas suggest the presence of a weak plume beneath the area. The eruption of the large Payún Matrú volcano and the gigantic Pleistocene flood basalts also calls for a thermal anomaly to produce these melts during a weakly compressive tectonic regime with no significant addition of slab fluids. This was supported by Burd et al. (2008, Abstr., 7th Int. Sym. And. Geo.) who recognized a plume-like conductive structure beneath Payún Matrú volcano on an electrical resistivity profile across the Payún Matrú volcanic field. The many Argentine and Chile Ridge EM1 basalts form part of the global DUPAL-anomaly (Hart, 1984, Nature 309) which suggests a common mode of formation of the enriched mantle sources; most likely anciently subducted components in the underlying upper mantle, either in a larger reservoir or as dispersed bodies of material. From there they can rise as small plumes or be entrained in a convecting MORB source mantle.

Investigating In-Situ Mass Transfer Processes in a Groundwater U Plume Influenced by Groundwater-River Hydrologic and Geochemical Coupling (Invited)

NASA Astrophysics Data System (ADS)

Zachara, J. M.

2009-12-01

The Hanford Integrated Field Research Challenge (IFRC) site is a DOE/BER-supported experimental and monitoring facility focused on multi-scale mass transfer processes (hanfordifc@pnl.gov). It is located within the footprint of a historic uranium (U) waste disposal pond that overlies a contaminated vadose zone and a 1 km+ groundwater U plume. The plume is under a regulatory clean-up mandate. The site is in hydraulic connectivity with the Columbia River that is located approximately 300 m distant. Dramatic seasonal variations in Columbia River stage cause 2m+ variations in water table and associated changes in groundwater flow directions and composition that are believed to recharge contaminant U to the plume through lower vadose zone pumping. The 60 m triangular shaped facility contains 37 monitoring wells equipped with down-hole electrical resistance tomography electrode and thermistor arrays, pressure transducers for continual water level monitoring, and specific conductance electrodes. Well spacings allow cross-hole geophysical interrogation and dynamic plume monitoring. Various geophysical and hydrologic field characterizations were performed during and after well installation, and retrieved sediments are being subjected to a hierarchal laboratory characterization process to support geostatistical models of hydrologic properties, U(VI) distribution and speciation, and equilibrium and kinetic reaction parameters for robust but tractable field-scale reactive transport calculations. Three large scale (10,000 gal+), non-reactive tracer experiments have been performed to evaluate groundwater flowpaths and velocities, facies scale mass transfer, and subsurface heterogeneity effects under different hydrologic conditions (e.g., flow vectors toward or away from the river). A passive monitoring experiment was completed during spring and summer of 2009 that documents spatially variable U(VI) release and plume recharge from the contaminated lower vadose zone during oscillating rising and falling water table events. A large scale injection experiment to evaluate in situ U(VI) desorption kinetics controlled by mass transfer is planned for the fall of 2009. The presentation will summarize key results from these different activities, and discuss their implications to improved plume forecasting and development of an effective groundwater remedy.

Biomass burning influence on high latitude tropospheric ozone and reactive nitrogen in summer 2008: a multi-model analysis based on POLMIP simulations

NASA Astrophysics Data System (ADS)

Arnold, S. R.; Emmons, L. K.; Monks, S. A.; Law, K. S.; Ridley, D. A.; Turquety, S.; Tilmes, S.; Thomas, J. L.; Bouarar, I.; Flemming, J.; Huijnen, V.; Mao, J.; Duncan, B. N.; Steenrod, S.; Yoshida, Y.; Langner, J.; Long, Y.

2014-09-01

We have evaluated tropospheric ozone enhancement in air dominated by biomass burning emissions at high laititudes (> 50˚ N) in July 2008, using 10 global chemical transport model simulations from the POLMIP multi-model comparison exercise. In model air masses dominated by fire emissions, Δ O3/ΔCO values ranged between 0.039 and 0.196 ppbv ppbv-1 (mean: 0.113 ppbv ppbv-1) in freshly fire-influenced air, and between 0.140 and 0.261 ppbv ppbv-1 (mean: 0.193 ppbv) in more aged fire-influenced air. These values are in broad agreement with the range of observational estimates from the literature. Model ΔPAN/ΔCO enhancement ratios show distinct groupings according to the meteorological data used to drive the models. ECMWF-forced models produce larger ΔPAN/ΔCO values (4.44-6.28 pptv ppbv-1) than GEOS5-forced models (2.02-3.02 pptv ppbv-1), which we show is likely linked to differences efficiency of vertical transport during poleward export from mid-latitude source regions. Simulations of a large plume of biomass burning and anthropogenic emissions exported from Asia towards the Arctic using a Lagrangian chemical transport model show that 4 day net ozone change in the plume is sensitive to differences in plume chemical composition and plume vertical position among the POLMIP models. In particular, Arctic ozone evolution in the plume is highly sensitive to initial concentrations of PAN, as well as oxygenated VOCs (acetone, acetaldehyde), due to their role in producing the peroxyacetyl radical PAN precursor. Vertical displacement is also important due to its effects on the stability of PAN, and subsequent effect on NOx abundance. In plumes where net ozone production is limited, we find that the lifetime of ozone in the plume is sensitive to hydrogen peroxide loading, due to the production of HO2 from peroxide photolysis, and the key role of HO2 + O3 in controlling ozone loss. Overall, our results suggest that emissions from biomass burning lead to large-scale photochemical enhancement in high latitude tropospheric ozone during summer.

Biomass burning influence on high-latitude tropospheric ozone and reactive nitrogen in summer 2008: a multi-model analysis based on POLMIP simulations

NASA Astrophysics Data System (ADS)

Arnold, S. R.; Emmons, L. K.; Monks, S. A.; Law, K. S.; Ridley, D. A.; Turquety, S.; Tilmes, S.; Thomas, J. L.; Bouarar, I.; Flemming, J.; Huijnen, V.; Mao, J.; Duncan, B. N.; Steenrod, S.; Yoshida, Y.; Langner, J.; Long, Y.

2015-06-01

We have evaluated tropospheric ozone enhancement in air dominated by biomass burning emissions at high latitudes (> 50° N) in July 2008, using 10 global chemical transport model simulations from the POLMIP multi-model comparison exercise. In model air masses dominated by fire emissions, ΔO3/ΔCO values ranged between 0.039 and 0.196 ppbv ppbv-1 (mean: 0.113 ppbv ppbv-1) in freshly fire-influenced air, and between 0.140 and 0.261 ppbv ppbv-1 (mean: 0.193 ppbv) in more aged fire-influenced air. These values are in broad agreement with the range of observational estimates from the literature. Model ΔPAN/ΔCO enhancement ratios show distinct groupings according to the meteorological data used to drive the models. ECMWF-forced models produce larger ΔPAN/ΔCO values (4.47 to 7.00 pptv ppbv-1) than GEOS5-forced models (1.87 to 3.28 pptv ppbv-1), which we show is likely linked to differences in efficiency of vertical transport during poleward export from mid-latitude source regions. Simulations of a large plume of biomass burning and anthropogenic emissions exported from towards the Arctic using a Lagrangian chemical transport model show that 4-day net ozone change in the plume is sensitive to differences in plume chemical composition and plume vertical position among the POLMIP models. In particular, Arctic ozone evolution in the plume is highly sensitive to initial concentrations of PAN, as well as oxygenated VOCs (acetone, acetaldehyde), due to their role in producing the peroxyacetyl radical PAN precursor. Vertical displacement is also important due to its effects on the stability of PAN, and subsequent effect on NOx abundance. In plumes where net ozone production is limited, we find that the lifetime of ozone in the plume is sensitive to hydrogen peroxide loading, due to the production of HOx from peroxide photolysis, and the key role of HO2 + O3 in controlling ozone loss. Overall, our results suggest that emissions from biomass burning lead to large-scale photochemical enhancement in high-latitude tropospheric ozone during summer.

CHLORINATED SOLVENT PLUME CONTROL

EPA Science Inventory

This lecture will cover recent success in controlling and assessing the treatment of shallow ground water plumes of chlorinated solvents, other halogenated organic compounds, and methyl tert-butyl ether (MTBE).

Method and apparatus for chemical and topographical microanalysis

NASA Technical Reports Server (NTRS)

Kossakovski, Dmitri A. (Inventor); Baldeschwieler, John D. (Inventor); Beauchamp, Jesse L. (Inventor)

2002-01-01

A scanning probe microscope is combined with a laser induced breakdown spectrometer to provide spatially resolved chemical analysis of the surface correlated with the surface topography. Topographical analysis is achieved by scanning a sharp probe across the sample at constant distance from the surface. Chemical analysis is achieved by the means of laser induced breakdown spectroscopy by delivering pulsed laser radiation to the sample surface through the same sharp probe, and consequent collection and analysis of emission spectra from plasma generated on the sample by the laser radiation. The method comprises performing microtopographical analysis of the sample with a scanning probe, selecting a scanned topological site on the sample, generating a plasma plume at the selected scanned topological site, and measuring a spectrum of optical emission from the plasma at the selected scanned topological site. The apparatus comprises a scanning probe, a pulsed laser optically coupled to the probe, an optical spectrometer, and a controller coupled to the scanner, laser and spectrometer for controlling the operation of the scanner, laser and spectrometer. The probe and scanner are used for topographical profiling the sample. The probe is also used for laser radiation delivery to the sample for generating a plasma plume from the sample. Optical emission from the plasma plume is collected and delivered to the optical spectrometer so that analysis of emission spectrum by the optical spectrometer allows for identification of chemical composition of the sample at user selected sites.

Isotopic evolution of Mauna Loa and the chemical structure of the Hawaiian plume

NASA Astrophysics Data System (ADS)

Depaolo, Donald J.; Bryce, Julia G.; Dodson, Allen; Shuster, David L.; Kennedy, B. Mack

2001-07-01

New He isotopic data from the HSDP pilot hole core, lava accumulation rate models, and data from the literature are used to develop a 200,000 year isotopic record for the lava erupted from the Mauna Loa volcano. This record, coupled with an analogous record from Mauna Kea from the Hawaii Scientific Drilling Project (HSDP) pilot hole project and other literature data from the GEOROC database, are used to construct a "map" of lava isotopic compositions for the island of Hawaii. The isotopic map is converted to a map of the He and Nd isotopic compositions of melts from the mantle plume, which can be compared with a published melt supply map derived from geodynamic modeling. The resulting map of the plume indicates that values of helium 3He/4He > 20 Ra are confined to the core of the plume (radius ≈ 20-25 km) and correspond to potential temperatures >1565°C, suggesting the He isotopic signal is derived from deep in the mantle. The 3He/4He map has closed contours down to 10 Ra; the contours are teardrop-shaped and elongated in the general direction of plate motion. The closed contours indicate that most of the plume He signal is lost during the early stages of melting, which is consistent with helium behaving as a strongly incompatible element (KHe ≤ 0.001). The ɛNd contours (and by inference the contours for Sr, Pb, Hf, and Os) do not all close on the scale of the island of Hawaii but instead partially follow material flow lines within the plume beneath the lithosphere. The plume signal for Nd extends circa 100 km in the direction of plate motion, which is consistent with the moderately incompatible behavior of Nd (KNd ≈ 0.02). Downstream from the plume core epicenter, plume Nd occurs with asthenospheric He; this could be mistaken for an additional plume component, whereas it may be only a manifestation of differing incompatibility. Data from Mauna Loa suggest the presence of a low-3He/4He plume component that has low ɛNd and high 87Sr/86Sr. The plume map suggests that this component may be a blob (circa 20 km scale), located between Mauna Loa and Hualalai and separated from the main plume core by a zone of more asthenosphere-like material. The HSDP data preclude a proposed model where this material represents a ring of entrained material from the lower mantle. The orientation of the elongation of contours on the plume He and Nd isotope maps (˜N45°W) does not match the modern plate motion as measured by GPS (N65°W) nor does it match the trend of the ridge axis between Maui and Loihi (N30°W). The geochemical evidence, as well as the locations and growth histories of the Hawaiian volcanoes, suggest that the plume, as well as the Pacific plate, has been moving at a velocity of several centimeters per year over the past 1 to 2 million years.

Gas and hydrogen isotopic analyses of volcanic eruption clouds in Guatemala sampled by aircraft

USGS Publications Warehouse

Rose, W.I.; Cadle, R.D.; Heidt, L.E.; Friedman, I.; Lazrus, A.L.; Huebert, B.J.

1980-01-01

Gas samples were collected by aircraft entering volcanic eruption clouds of three Guatemalan volcanoes. Gas chromatographic analyses show higher H2 and S gas contents in ash eruption clouds and lower H2 and S gases in vaporous gas plumes. H isotopic data demonstrate lighter isotopic distribution of water vapor in ash eruption clouds than in vaporous gas plumes. Most of the H2O in the vaporous plumes is probably meteoric. The data are the first direct gas analyses of explosive eruptive clouds, and demonstrate that, in spite of atmospheric admixture, useful compositional information on eruptive gases can be obtained using aircraft. ?? 1980.

Nd-Sr-Pb isotopic variations along the Gulf of Aden - Evidence for Afar mantle plume-continental lithosphere interaction

NASA Astrophysics Data System (ADS)

Schilling, Jean-Guy; Kingsley, Richard H.; Hanan, Barry B.; McCully, Brian L.

1992-07-01

The rare-earth-element concentrations and Nd, Sr, and Pb isotopic compositions of the basalts in the Gulf of Aden are described and related to asthenospheric and lithospheric interactions with a thermal toruslike plume. Specific attention is given to the spatial and temporal traits of the mantle sources, and isotopic and geochemical data are used to determine the extent to which basaltic volcanism is derived from a mantle plume, the mantle lithosphere, and upwelling of the depleted atmosphere. The impingement and dispersion of a plume head is confirmed beneath the Afar region, and the geological record shows continental stretching and rifting prior to the impingement in the outskirts of the Horn of Africa. The data suggest that the isotopic variations along the Gulf of Aden/Red Sea/Ethiopia Rift system can be explained by the interaction of a thermal toruslike plume with the depleted asthenosphere and the overlying continental mantle lithosphere.

Investigation of power-plant plume photochemistry using a reactive plume model

NASA Astrophysics Data System (ADS)

Kim, Y. H.; Kim, H. S.; Song, C. H.

2016-12-01

Emissions from large-scale point sources have continuously increased due to the rapid industrial growth. In particular, primary and secondary air pollutants are directly relevant to atmospheric environment and human health. Thus, we tried to precisely describe the atmospheric photochemical conversion from primary to secondary air pollutants inside the plumes emitted from large-scale point sources. A reactive plume model (RPM) was developed to comprehensively consider power-plant plume photochemistry with 255 condensed photochemical reactions. The RPM can simulate two main components of power-plant plumes: turbulent dispersion of plumes and compositional changes of plumes via photochemical reactions. In order to evaluate the performance of the RPM developed in the present study, two sets of observational data obtained from the TexAQS II 2006 (Texas Air Quality Study II 2006) campaign were compared with RPM-simulated data. Comparison shows that the RPM produces relatively accurate concentrations for major primary and secondary in-plume species such as NO2, SO2, ozone, and H2SO4. Statistical analyses show good correlation, with correlation coefficients (R) ranging from 0.61 to 0.92, and good agreement with the Index of Agreement (IOA) ranging from 0.70 to 0.95. Following evaluation of the performance of the RPM, a demonstration was also carried out to show the applicability of the RPM. The RPM can calculate NOx photochemical lifetimes inside the two plumes (Monticello and Welsh power plants). Further applicability and possible uses of the RPM are also discussed together with some limitations of the current version of the RPM.

The geochemical and Sr-Nd-Pb-He isotopic characterization of the mantle source of Rungwe Volcanic Province: comparison with the Afar mantle domain

NASA Astrophysics Data System (ADS)

Castillo, P. R.; Hilton, D. R.; Halldorsson, S. A.; Wang, R.

2012-12-01

The ultimate source of heat and magmatism associated with continental rifting in the East African Rift System (EARS) is generally viewed to be the African Superplume, but there is continuing debate on the surface expression of this large anomalous feature, which originates in the lower mantle. Previous studies have demonstrated an insignificant role for crustal contamination thereby identifying a single mantle plume signature in Quaternary basalts from the Main Ethiopian Rift in the northern EARS. This is designated to be the Afar plume and is characterized by, e.g., 3He/4He >15 RA, 206Pb/204Pb = 19.5 and 87Sr/86Sr = 0.7035 [Rooney et al., J. Pet. 53, 2012]. In contrast, the signature of plume(s) in the southern EARS is less constrained. Rogers et al. [EPSL 176, 2000] proposed a plume in the sub-lithospheric Kenyan mantle with characteristically lower 43Nd/144Nd than the Afar plume whereas Furman [JAES 48, 2007] advocated a high μ [HIMU] plume based primarily on the high 206Pb/204Pb ratios of lavas in all areas within and south of the Turkana Depression: both models assume a 3He/4He lower than the Afar plume. Here we report the trace element and Sr-Nd-Pb isotopic composition of basaltic lavas from the Rungwe Volcanic Province (RVP) in the southern extreme of the Western Rift previously identified as a high 3He/4He locality (~15 RA; [Hilton et al., GRL 38, 2011]). Trace element analyses are within the previously reported range of lava compositions that include a relatively large lithospheric component. More importantly, we identify correlations among incompatible trace element and isotopic ratios (e.g., 3He/4He vs 206Pb/204Pb, Rb/Sr, Nb/Ta; 87Sr/86Sr vs 208Pb/204Pb). Our new results suggest the presence of a distinct, high 3He/4He mantle source beneath RVP that is more radiogenic (e.g., 206Pb/204Pb up to ~19.8; 87Sr/86Sr up to 0.7055) than the Afar mantle plume. There is also very little or no HIMU signature in RPV basalts based on their high Sr and low Nd isotopic ratios.

Formation and evolution of a metasomatized lithospheric root at the motionless Antarctic plate: the case of East Island, Crozet Archipelago (Indian Ocean)

NASA Astrophysics Data System (ADS)

Meyzen, Christine; Marzoli, Andrea; Bellieni, Giuliano; Levresse, Gilles

2016-04-01

Sitting atop the nearly stagnant Antarctic plate (ca. 6.46 mm/yr), the Crozet archipelago midway between Madagascar and Antarctica constitutes a region of unusually shallow (1543-1756 m below sea level) and thickened oceanic crust (10-16.5 km), high geoid height, and deep low-velocity zone, which may reflect the surface expression of a mantle plume. Here, we present new major and trace element data for Quaternary sub-aerial alkali basalts from East Island, the easterly and oldest island (ca. 9 Ma) of the Crozet archipelago. Crystallization at uppermost mantle depth and phenocryst accumulation have strongly affected their parental magma compositions. Their trace element patterns show a large negative K anomaly relative to Ta-La, moderate depletions in Rb and Ba with respect to Th-U, and heavy rare earth element (HREE) depletions relative to light REE. These characteristics allow limits to be placed upon the composition and mineralogy of their mantle source. The average trace element spectrum of East Island basalts can be matched by melting of about 2 % of a garnet-phlogopite-bearing peridotite source. The stability field of phlogopite restricts melting depth to lithospheric levels. The modelled source composition requires a multistage evolution, where the mantle has been depleted by melt extraction before having been metasomatized by alkali-rich plume melts. The depleted mantle component may be sourced by residual mantle plume remnants stagnated at the melting locus due to a weak lateral flow velocity inside the melting regime, whose accumulation progressively edifies a depleted lithospheric root above the plume core. Low-degree alkali-rich melts are likely derived from the plume source. Such a mantle source evolution may be general to both terrestrial and extraterrestrial environments where the lateral component velocity of the mantle flow field is extremely slow.

Cutting through the smoke: the diversity of microorganisms in deep-sea hydrothermal plumes

PubMed Central

Mikalsen, Svein-Ole; Giebel, Helge-Ansgar; Rogers, Alex D.

2017-01-01

There are still notable gaps regarding the detailed distribution of microorganisms between and within insular habitats such as deep-sea hydrothermal vents. This study investigates the community composition of black smoker vent microorganisms in the Southern Hemisphere, and changes thereof along a spatial and chemical gradient ranging from the vent plume to surrounding waters. We sampled two hydrothermal vent fields, one at the South West Indian Ridge (SWIR), the other at the East Scotia Ridge (ESR). Samples were collected across vent fields at varying vertical distances from the origin of the plumes. The microbial data were sequenced on an Illumina MiSeq platform for the 16SrRNA gene. A substantial amount of vent-specific putative chemosynthetic microorganisms were found, particularly in samples from focused hydrothermal venting. Common vent-specific organisms from both vent fields were the genera Arcobacter, Caminibacter and Sulfurimonas from the Epsilonproteobacteria and the SUP05 group from the Gammaproteobacteria. There were no major differences in microbial composition between SWIR and ESR for focused plume samples. However, within the ESR the diffuse flow and focused samples differed significantly in microbial community composition and relative abundance. For Epsilonproteobacteria, we found evidence of niche-specificity to hydrothermal vent environments. This taxon decreased in abundance by three orders of magnitude from the vent orifice to background water. Epsilonproteobacteria distribution followed a distance–decay relationship as vent-effluents mixed with the surrounding seawater. This study demonstrates strong habitat affinity of vent microorganisms on a metre scale with distinct environmental selection. PMID:28484604

Airborne In-Situ Trace Gas Measurements of Multiple Wildfires in California (2013-2014)

NASA Astrophysics Data System (ADS)

Iraci, L. T.; Yates, E. L.; Tanaka, T.; Roby, M.; Gore, W.; Clements, C. B.; Lareau, N.; Ambrosia, V. G.; Quayle, B.; Schroeder, W.

2014-12-01

Biomass burning emissions are an important source of a wide range of trace gases and particles that can impact local, regional and global air quality, climate forcing, biogeochemical cycles and human health. In the western US, wildfires dominate over prescribed fires, contributing to atmospheric trace gas budgets and regional and local air pollution. Limited sampling of emissions from wildfires means western US emission estimates rely largely on data from prescribed fires, which may not be a suitable proxy for wildfire emissions. We report here in-situ measurements of carbon dioxide, methane, ozone and water vapor from the plumes of a variety of wildfires sampled in California in the fire seasons of 2013 and 2014. Included in the analysis are the Rim Fire (August - October 2013, near Yosemite National Park), the Morgan Fire (September 2013, near Clayton, CA), and the El Portal Fire (July - August 2014, in Yosemite National Park), among others. When possible, fires were sampled on multiple days. Emission ratios and estimated emission factors will be presented and discussed in the context of fuel composition, plume structure, and fire phase. Correlations of plume chemical composition to MODIS/VIIRS Fire Radiative Power (FRP) and other remote sensing information will be explored. Furthermore, the role of plumes in delivery of enhanced ozone concentrations to downwind municipalities will be discussed.

The interaction of Io's plumes and sublimation atmosphere

NASA Astrophysics Data System (ADS)

McDoniel, William J.; Goldstein, David B.; Varghese, Philip L.; Trafton, Laurence M.

2017-09-01

Io's volcanic plumes are the ultimate source of its SO2 atmosphere, but past eruptions have covered the moon in surface frost which sublimates in sunlight. Today, Io's atmosphere is a result of some combination of volcanism and sublimation, but it is unknown exactly how these processes work together to create the observed atmosphere. We use the direct simulation Monte Carlo (DSMC) method to model the interaction of giant plumes with a sublimation atmosphere. Axisymmetric plume/atmosphere simulations demonstrate that the total mass of SO2 above Io's surface is only poorly approximated as the sum of independent volcanic and sublimated components. A simple analytic model is developed to show how variation in the mass of erupting gas above Io's surface can counteract variation in the mass of its hydrostatic atmosphere as surface temperature changes over a Jupiter year. Three-dimensional, unsteady simulations of giant plumes over an Io day are also presented, showing how plume material becomes suspended in the sublimation atmosphere. We find that a plume which produces some total mass above Io's surface at night will cause a net increase in the noon-time atmosphere of only a fraction of the night-time value. However, as much as seven times the night-side mass of the plume will become suspended in the sublimation atmosphere, altering its composition and displacing sublimated material.

Local Sensitivity of Predicted CO 2 Injectivity and Plume Extent to Model Inputs for the FutureGen 2.0 site

DOE PAGES

Zhang, Z. Fred; White, Signe K.; Bonneville, Alain; ...

2014-12-31

Numerical simulations have been used for estimating CO2 injectivity, CO2 plume extent, pressure distribution, and Area of Review (AoR), and for the design of CO2 injection operations and monitoring network for the FutureGen project. The simulation results are affected by uncertainties associated with numerous input parameters, the conceptual model, initial and boundary conditions, and factors related to injection operations. Furthermore, the uncertainties in the simulation results also vary in space and time. The key need is to identify those uncertainties that critically impact the simulation results and quantify their impacts. We introduce an approach to determine the local sensitivity coefficientmore » (LSC), defined as the response of the output in percent, to rank the importance of model inputs on outputs. The uncertainty of an input with higher sensitivity has larger impacts on the output. The LSC is scalable by the error of an input parameter. The composite sensitivity of an output to a subset of inputs can be calculated by summing the individual LSC values. We propose a local sensitivity coefficient method and applied it to the FutureGen 2.0 Site in Morgan County, Illinois, USA, to investigate the sensitivity of input parameters and initial conditions. The conceptual model for the site consists of 31 layers, each of which has a unique set of input parameters. The sensitivity of 11 parameters for each layer and 7 inputs as initial conditions is then investigated. For CO2 injectivity and plume size, about half of the uncertainty is due to only 4 or 5 of the 348 inputs and 3/4 of the uncertainty is due to about 15 of the inputs. The initial conditions and the properties of the injection layer and its neighbour layers contribute to most of the sensitivity. Overall, the simulation outputs are very sensitive to only a small fraction of the inputs. However, the parameters that are important for controlling CO2 injectivity are not the same as those controlling the plume size. The three most sensitive inputs for injectivity were the horizontal permeability of Mt Simon 11 (the injection layer), the initial fracture-pressure gradient, and the residual aqueous saturation of Mt Simon 11, while those for the plume area were the initial salt concentration, the initial pressure, and the initial fracture-pressure gradient. The advantages of requiring only a single set of simulation results, scalability to the proper parameter errors, and easy calculation of the composite sensitivities make this approach very cost-effective for estimating AoR uncertainty and guiding cost-effective site characterization, injection well design, and monitoring network design for CO2 storage projects.« less

Hubble Sees Recurring Plume Erupting From Europa

NASA Image and Video Library

2017-04-13

These composite images show a suspected plume of material erupting two years apart from the same location on Jupiter's icy moon Europa. The images bolster evidence that the plumes are a real phenomenon, flaring up intermittently in the same region on the satellite. Both plumes, photographed in ultraviolet light by NASA's Hubble's Space Telescope Imaging Spectrograph, were seen in silhouette as the moon passed in front of Jupiter. The newly imaged plume, shown at right, rises about 62 miles (100 kilometers) above Europa's frozen surface. The image was taken Feb. 22, 2016. The plume in the image at left, observed by Hubble on March 17, 2014, originates from the same location. It is estimated to be about 30 miles (50 kilometers) high. The snapshot of Europa, superimposed on the Hubble image, was assembled from data from NASA's Galileo mission to Jupiter. The plumes correspond to the location of an unusually warm spot on the moon's icy crust, seen in the late 1990s by the Galileo spacecraft (see PIA21444). Researchers speculate that this might be circumstantial evidence for water venting from the moon's subsurface. The material could be associated with the global ocean that is believed to be present beneath the frozen crust. https://photojournal.jpl.nasa.gov/catalog/PIA21443

Development and application of gas diffusion denuder sampling techniques with in situ derivatization for the determination of hydrogen halides in volcanic plumes

NASA Astrophysics Data System (ADS)

Gutmann, Alexandra; Rüdiger, Julian; Bobrowski, Nicole; Hoffmann, Thorsten

2017-04-01

Volcanoes emit large amounts of gases into the atmosphere. The gas composition in volcanic plumes vary, driven by subsurface processes (such as magma rising) as well as by chemical reactions within the plume after mixing with ambient air. The knowledge of the gas composition can be a useful tool to monitor volcanic activity changes. However, to use the plume composition as a monitoring parameter, it is essential to understand the chemical reactions inside volcanic plumes, in particular when interpretation of volcanic activity changes is based on reactive gas species, such as bromine monoxide or molecular halogens. Changes in BrO/SO2-ratios, measured by UV spectrometers, have already been interpreted in connection with increasing volcanic activity prior to eruptions. But the abundance of BrO changes as a function of the reaction time, and therefore with distance from the vent, as well as the spatial position in the plume. Actually model and field studies assume a non-direct emission of BrO, but its formation due to photochemical and multiphase reactions involving gas and particle phase of volcanic emission mixed with the surrounding atmosphere. However, same models presume HBr as initially emitted species. Therefore, HBr is an important species linking BrO to geophysical processes in volcanic systems. Due to the lack of analytical methods for the accurate speciation of certain halogens (HBr, Br2, Br, BrCl, HOBr, etc.) there are still large uncertainties about the magnitude of volcanic halogen emissions, and in the understanding of the bromine chemistry in volcanic plumes. Since the concentrations of hydrogen halides are not directly accesable by remote sensing techniques, an in situ method with coated gas diffusion denuder was developed. The method uses selective derivatization reaction of gaseous hydrogen halides with an organic compound for the enrichment and immobilization. For this task 5,6-Epoxy-5,6-dihydro-1,10-phenanthrolin was identified as a suitable derivatization agent. The reaction with HBr results in the formation of 5-Bromo-5,6-dihydro-6-hydroxy-1,10-phenanthrolin. Other hydrogen halides give corresponding products. Using a denuder based sampling system with in situ derivatization it is also possible to differentiate even between gaseous and particulate hydrogen bromine. The derivatized analytes were analyzed with high pressure liquid chromatography-mass spectrometry. We applied this approach to measure hydrogen halide mixing ratios (ppt to ppb range depending on plume age) in the plumes of different volcanoes: Stromboli, Italy; Masaya, Nicaragua; Turrialba, Costa Rica. The results of this measurements will be presented. Samples were taken at various distances to the emission source and have been compared with complementary data (e.g. SO2 from alkaline traps or gas sensors). Furthermore, the sampling method has been applied on an unmanned aerial vehicle for downwind sample collection.

Geodynamic modelling of low-buoyancy thermo-chemical plumes

NASA Astrophysics Data System (ADS)

Dannberg, Juliane; Sobolev, Stephan

2015-04-01

The Earth's biggest magmatic events that form Large Igneous Provinces are believed to originate from massive melting when hot mantle plumes rising from the lowermost mantle reach the base of the lithosphere. Classical models of thermal mantle plumes predict a flattening of the plume head to a disk-like structure, a kilometer-scale surface uplift just before the initiation of LIPs and thin plume tails. However, there are seismic observations and paleo-topography data that are difficult to explain with this classical approach. Here, using numerical models, we show that the issue can be resolved if major mantle plumes are thermo-chemical rather than purely thermal. It has been suggested a long time ago that subducted oceanic crust could be recycled by mantle plumes; and based on geochemical data, they may contain up to 15-20% of this recycled material in the form of dense eclogite, which drastically decreases their buoyancy and makes it depth-dependent. We perform numerical experiments in a 3D spherical shell geometry to investigate the dynamics of the plume ascent, the interaction between plume- and plate-driven flow and the dynamics of melting in a plume head. For this purpose, we use the finite-element code ASPECT, which allows for complex temperature-, pressure- and composition-dependent material properties. Moreover, our models incorporate phase transitions (including melting) with the accompanying rheological and density changes, Clapeyron slopes and latent heat effects for both peridotite and eclogite, mantle compressibility and a strong temperature- and depth-dependent viscosity. We demonstrate that despite their low buoyancy, such plumes can rise through the whole mantle causing only negligible surface uplift. Conditions for this ascent are high plume volume and moderate lower mantle subadiabaticity. While high plume buoyancy results in plumes directly advancing to the base of the lithosphere, plumes with slightly lower buoyancy pond in a depth of 300-400 km and form pools or a second layer of hot material. These structures are caused by phase transitions occurring in different depths in peridotite and eclogite; and they become asymmetric and finger-like channels begin to form when the plume gets entrained by a quickly moving overlying plate. We also show that the bulky tails of large and hot low-buoyancy plumes are stable for several tens of millions of years and that their shapes fit seismic tomography data much better than the narrow tails of thermal plumes.

Generation of dendrite fragments and their transport from within the mushy zone

NASA Astrophysics Data System (ADS)

Liu, Shan

Five steps have been identified for the grain structure evolution of a casting by an intrinsic mechanism: (i) fragmentation of dendrites in the mushy region; (ii) transport of these dendrite fragments from within this region; (iii) their survival in the bulk liquid; (iv) growth of the survivors; and (v) blockage of the columnar crystal growth front and formation of the equiaxed grains in a casting. Of these, the first two steps remain unclear and are explored in this study. It is found that deceleration of the growth interface leads to fragmentation of side arms from primary stems. This process can be characterized by the Fragmentation Percentage which is related to the magnitude and range of the deceleration, time, and the alloy composition. With decelerations, though temperature gradient at the interface does not change, the dendrite array exhibits important microstructural variations: the dendrite, tip restabilizes rather rapidly (<10 min) and correlates well with the instantaneous tip velocity; and the primary arm spacing restabilization takes ˜5 times longer than the tip readjustment. The difference between the rates of restabilization of the tip radius and primary arm spacing causes slight solute enrichment in the interdendritic region, resulting in side arm detachment. Through a comparative study with the steady state growth process, the magnitude of this solute enrichment is estimated. Further analysis for the dissolution kinetics shows that the excessive solute can only cause a partial dissolution at the neck of a side arm, but this is sufficient to upset the curvature balance between the different sections of a dendritic structure and the continual dissolution at the neck is subsequently driven by the curvature difference until a side arm is detached from the primary stalk. The solidification interface of most castings generally proceeds in a decelerated manner; therefore dendrite fragments already exist in the mushy region. These dendrite fragments can become the nuclei for the central equiaxed zone of a casting or ingot if they are transported out of the mushy zone and into the bulk liquid. The transport may be carried out by natural convection, with channel/plume flow as the most effective carrier; plume velocity and channel diameter are critical for the escape of the dendrite fragments. The selection criteria for them are investigated herein. A new experimental technique of constrained plume promotion has been devised to study the fluid flow behavior. With the simultaneous measurements of the interface advancing velocities, plume flow velocity, composition and temperature of both the plume and the bulk liquid (therefore the buoyancy), the overall flow behavior is quantified and the permeability of the dendrite mushy region is obtained. A model is established to describe natural plume flow and determine the factors for channel size/plume velocity selection. With the results of the constrained case, it is found that the size of a channel is determined by the ratio of the pressure effecting the entrainment in the mush and the pressure necessary for the vertical plume flow, while the absolute value of the pressure controls the plume velocity. Estimates agree well with previous experimental observations. With the number of fragments generated by deceleration and that transported by the entrainment flow, an estimate is made of how many fragments are convected out from the mushy region; this agrees with experimental observations reasonably well.

[INVITED] Control of femtosecond pulsed laser ablation and deposition by temporal pulse shaping

NASA Astrophysics Data System (ADS)

Garrelie, Florence; Bourquard, Florent; Loir, Anne--Sophie; Donnet, Christophe; Colombier, Jean-Philippe

2016-04-01

This study explores the effects of temporal laser pulse shaping on femtosecond pulsed laser deposition (PLD). The potential of laser pulses temporally tailored on ultrafast time scales is used to control the expansion and the excitation degree of ablation products including atomic species and nanoparticles. The ablation plume generated by temporally shaped femtosecond pulsed laser ablation of aluminum and graphite targets is studied by in situ optical diagnostic methods. Taking advantage of automated pulse shaping techniques, an adaptive procedure based on spectroscopic feedback regulates the irradiance for the enhancement of typical plasma features. Thin films elaborated by unshaped femtosecond laser pulses and by optimized sequence indicate that the nanoparticles generation efficiency is strongly influenced by the temporal shaping of the laser irradiation. The ablation processes leading either to the generation of the nanoparticles either to the formation of plasma can be favored by using a temporal shaping of the laser pulse. Insights are given on the possibility to control the quantity of the nanoparticles. The temporal laser pulse shaping is shown also to strongly modify the laser-induced plasma contents and kinetics for graphite ablation. Temporal pulse shaping proves its capability to reduce the number of slow radicals while increasing the proportion of monomers, with the addition of ionized species in front of the plume. This modification of the composition and kinetics of plumes in graphite ablation using temporal laser pulse shaping is discussed in terms of modification of the structural properties of deposited Diamond-Like Carbon films (DLC). This gives rise to a better understanding of the growth processes involved in femtosecond-PLD and picosecond-PLD of DLC suggesting the importance of neutral C atoms, which are responsible for the subplantation process.

The tropospheric processing of acidic gases and hydrogen sulphide in volcanic gas plumes as inferred from field and model investigations

NASA Astrophysics Data System (ADS)

Aiuppa, A.; Franco, A.; von Glasow, R.; Allen, A. G.; D'Alessandro, W.; Mather, T. A.; Pyle, D. M.; Valenza, M.

2007-03-01

Improving the constraints on the atmospheric fate and depletion rates of acidic compounds persistently emitted by non-erupting (quiescent) volcanoes is important for quantitatively predicting the environmental impact of volcanic gas plumes. Here, we present new experimental data coupled with modelling studies to investigate the chemical processing of acidic volcanogenic species during tropospheric dispersion. Diffusive tube samplers were deployed at Mount Etna, a very active open-conduit basaltic volcano in eastern Sicily, and Vulcano Island, a closed-conduit quiescent volcano in the Aeolian Islands (northern Sicily). Sulphur dioxide (SO2), hydrogen sulphide (H2S), hydrogen chloride (HCl) and hydrogen fluoride (HF) concentrations in the volcanic plumes (typically several minutes to a few hours old) were repeatedly determined at distances from the summit vents ranging from 0.1 to ~10 km, and under different environmental conditions. At both volcanoes, acidic gas concentrations were found to decrease exponentially with distance from the summit vents (e.g., SO2 decreases from ~10 000 μg/m3at 0.1 km from Etna's vents down to ~7 μg/m3 at ~10 km distance), reflecting the atmospheric dilution of the plume within the acid gas-free background troposphere. Conversely, SO2/HCl, SO2/HF, and SO2/H2S ratios in the plume showed no systematic changes with plume aging, and fit source compositions within analytical error. Assuming that SO2 losses by reaction are small during short-range atmospheric transport within quiescent (ash-free) volcanic plumes, our observations suggest that, for these short transport distances, atmospheric reactions for H2S and halogens are also negligible. The one-dimensional model MISTRA was used to simulate quantitatively the evolution of halogen and sulphur compounds in the plume of Mt. Etna. Model predictions support the hypothesis of minor HCl chemical processing during plume transport, at least in cloud-free conditions. Larger variations in the modelled SO2/HCl ratios were predicted under cloudy conditions, due to heterogeneous chlorine cycling in the aerosol phase. The modelled evolution of the SO2/H2S ratios is found to be substantially dependent on whether or not the interactions of H2S with halogens are included in the model. In the former case, H2S is assumed to be oxidized in the atmosphere mainly by OH, which results in minor chemical loss for H2S during plume aging and produces a fair match between modelled and measured SO2/H2S ratios. In the latter case, fast oxidation of H2S by Cl leads to H2S chemical lifetimes in the early plume of a few seconds, and thus SO2 to H2S ratios that increase sharply during plume transport. This disagreement between modelled and observed plume compositions suggests that more in-detail kinetic investigations are required for a proper evaluation of H2S chemical processing in volcanic plumes.

The tropospheric processing of acidic gases and hydrogen sulphide in volcanic gas plumes as inferred from field and model investigations

NASA Astrophysics Data System (ADS)

Aiuppa, A.; Franco, A.; von Glasow, R.; Allen, A. G.; D'Alessandro, W.; Mather, T. A.; Pyle, D. M.; Valenza, M.

2006-11-01

Improving the constraints on the atmospheric fate and depletion rates of acidic compounds persistently emitted by non-erupting (quiescent) volcanoes is important for quantitatively predicting the environmental impact of volcanic gas plumes. Here, we present new experimental data coupled with modelling studies to investigate the chemical processing of acidic volcanogenic species during tropospheric dispersion. Diffusive tube samplers were deployed at Mount Etna, a very active open-conduit basaltic volcano in eastern Sicily, and Vulcano Island, a closed-conduit quiescent volcano in the Aeolian Islands (northern Sicily). Sulphur dioxide (SO2), hydrogen sulphide (H2S), hydrogen chloride (HCl) and hydrogen fluoride (HF) concentrations in the volcanic plumes (typically several minutes to a few hours old) were repeatedly determined at distances from the summit vents ranging from 0.1 to ~10 km, and under different environmental conditions. At both volcanoes, acidic gas concentrations were found to decrease exponentially with distance from the summit vents (e.g., SO2 decreases from ~10 000 μg/m3 at 0.1 km from Etna's vents down to ~7 μg/m3 at ~10 km distance), reflecting the atmospheric dilution of the plume within the acid gas-free background troposphere. Conversely, SO2/HCl, SO2/HF, and SO2/H2S ratios in the plume showed no systematic changes with plume aging, and fit source compositions within analytical error. Assuming that SO2 losses by reaction are small during short-range atmospheric transport within quiescent (ash-free) volcanic plumes, our observations suggest that, for these short transport distances, atmospheric reactions for H2S and halogens are also negligible. The one-dimensional model MISTRA was used to simulate quantitatively the evolution of halogen and sulphur compounds in the plume of Mt. Etna. Model predictions support the hypothesis of minor HCl chemical processing during plume transport, at least in cloud-free conditions. Larger variations in the modelled SO2/HCl ratios were predicted under cloudy conditions, due to heterogeneous chlorine cycling in the aerosol phase. The modelled evolution of the SO2/H2S ratios is found to be substantially dependent on whether or not the interactions of H2S with halogens are included in the model. In the former case, H2S is assumed to be oxidized in the atmosphere mainly by OH, which results in minor chemical loss for H2S during plume aging and produces a fair match between modelled and measured SO2/H2S ratios. In the latter case, fast oxidation of H2S by Cl leads to H2S chemical lifetimes in the early plume of a few seconds, and thus SO2 to H2S ratios that increase sharply during plume transport. This disagreement between modelled and observed plume compositions suggests that more in-detail kinetic investigations are required for a proper evaluation of H2S chemical processing in volcanic plumes.

Ion energy distributions and densities in the plume of Enceladus

NASA Astrophysics Data System (ADS)

Sakai, Shotaro; Cravens, Thomas E.; Omidi, Nojan; Perry, Mark E.; Waite, J. Hunter

2016-10-01

Enceladus has a dynamic plume that is emitting gas, including water vapor, and dust. The gas is ionized by solar EUV radiation, charge exchange, and electron impact and extends throughout the inner magnetosphere of Saturn. The charge exchange collisions alter the plasma composition. Ice grains (dust) escape from the vicinity of Enceladus and form the E ring, including a portion that is negatively charged by the local plasma. The inner magnetosphere within 10 RS (Saturn radii) contains a complex mixture of plasma, neutral gas, and dust that links back to Enceladus. In this paper we investigate the energy distributions, ion species and densities of water group ions in the plume of Enceladus using test particle and Monte Carlo methods that include collisional processes such as charge exchange and ion-neutral chemical reactions. Ion observations from the Cassini Ion and Neutral Mass Spectrometer (INMS) for E07 are presented for the first time. We use the modeling results to interpret observations made by the Cassini Plasma Spectrometer (CAPS) and the INMS. The low energy ions, as observed by CAPS, appear to be affected by a vertical electric field (EZ=-10 μV/m) in the plume. The EZ field may be associated with the charged dust and/or the pressure gradient of plasma. The model results, along with the results of earlier models, show that H3O+ ions created by chemistry are predominant in the plume, which agrees with INMS and CAPS data, but the INMS count rate in the plume for the model is several times greater than the data, which we do not fully understand. This composition and the total ion count found in the plume agree with INMS and CAPS data. On the other hand, the Cassini Langmuir Probe measured a maximum plume ion density more than 30,000 cm-3, which is far larger than the maximum ion density from our model, 900 cm-3. The model results also demonstrate that most of the ions in the plume are from the external magnetospheric flow and are not generated by local ionization. The origin of the ions in the plume was investigated using two different velocity models. Most ions were created by the interaction with background magnetospheric plasma and by photoionization. INMS and CAPS also detected water cluster ions. We will interpret these observations as a result of ion collisions with neutral water clusters, (H2O)n, originating in the tiger stripe vents as suggested by Tokar et al. (2009). We also estimated the process of generating cluster ions based on the INMS observations. We suggest that the most likely source is reaction of H3O+ with neutral water clusters or dimers such as (H2O)2 formed in the plume vents.

Effects of Plume Hydrodynamics and Oxidation on the Composition of a Condensing Laser-Induced Plasma

DOE PAGES

Weisz, David G.; Crowhurst, Jonathan C.; Finko, Mikhail S.; ...

2018-02-01

High-temperature chemistry in laser ablation plumes leads to vapor-phase speciation, which can induce chemical fractionation during condensation. In this work, using emission spectroscopy acquired after ablation of a SrZrO 3 target, we have experimentally observed the formation of multiple molecular species (ZrO and SrO) as a function of time as the laser ablation plume evolves. Although the stable oxides SrO and ZrO 2 are both refractory, we observed emission from the ZrO intermediate at earlier times than SrO. We deduced the time-scale of oxygen entrainment into the laser ablation plume using an 18O 2 environment by observing the in-growth ofmore » Zr 18O in the emission spectra relative to Zr 16O, which was formed by reaction of Zr with 16O from the target itself. Using temporally resolved plume-imaging, we determined that ZrO formed more readily at early times, volumetrically in the plume, while SrO formed later in time, around the periphery. Lastly, using a simple temperature-dependent reaction model, we have illustrated that the formation sequence of these oxides subsequent to ablation is predictable to first order.« less

ACE-FTS Observation of a Young Biomass Burning Plume: First Reported Measurements of C2H4, C3H6O, H2CO and PAN by Infrared Occultation from Space

NASA Technical Reports Server (NTRS)

Coheur, Pierre-Francois; Herbin, Herve; Clerbaux, Cathy; Hurtmans, Daniel; Wespes, Catherine; Carleer, Michel; Turquety, Solene; Rinsland, Curtis P.; Remedios, John; Hauglustaine, Didier;

Characterisation of particulate exposure during fireworks displays

NASA Astrophysics Data System (ADS)

Joly, Alexandre; Smargiassi, Audrey; Kosatsky, Tom; Fournier, Michel; Dabek-Zlotorzynska, Ewa; Celo, Valbona; Mathieu, David; Servranckx, René; D'amours, Réal; Malo, Alain; Brook, Jeffrey

2010-11-01

Little is known about the level and content of exposure to fine particles (PM 2.5) among persons who attend fireworks displays and those who live nearby. An evaluation of the levels of PM 2.5 and their elemental content was carried out during the nine launches of the 2007 Montréal International Fireworks Competition. For each event, a prediction of the location of the firework plume was obtained from the Canadian Meteorological Centre (CMC) of the Meteorological Service of Canada. PM 2.5 was measured continuously with a photometer (Sidepak™, TSI) within the predicted plume location ("predicted sites"), and integrated samples were collected using portable personal samplers. An additional sampler was located on a nearby roof ("fixed site"). The elemental composition of the collected PM 2.5 samples from the "predicted sites" was determined using both a non-destructive energy dispersive ED-XRF method and an ICP-MS method with a near-total microwave-assisted acid digestion. The elemental composition of the "fixed site" samples was determined by the ICP-MS with the near-total digestion method. The highest PM 2.5 levels reached nearly 10 000 μg m -3, roughly 1000 times background levels. Elements such as K, Cl, Al, Mg and Ti were markedly higher in plume-exposed filters. This study shows that 1) persons in the plume and in close proximity to the launch site may be exposed to extremely high levels of PM 2.5 for the duration of the display and, 2) that the plume contains specific elements for which little is known of their acute cardio-respiratory toxicity.

A nitrogen-rich septage-effluent plume in a glacial aquifer, Cape Cod, Massachusetts, February 1990 through December 1992

USGS Publications Warehouse

Desimone, Leslie A.; Barlow, Paul M.; Howes, Brian L.

1996-01-01

Physical, chemical, and microbial processes controlled transport of a nitrogen-rich ground-water plume through a glacial aquifer. Lithologic heterogeneity and vertical head gradients influenced plume movement and geometry. Nitrate was the predominant nitrogen form and oxygen was depleted in the ground-water plume. However, denitrification transformed only 2 percent of plume nitrogen because of limited organic-carbon availability. Aerobic respiration, nitrification and cation exchange (unsaturated zone) and ammonium sorption (saturated zone) had larger effects.

Coupled petrological-geodynamical modeling of a compositionally heterogeneous mantle plume

NASA Astrophysics Data System (ADS)

Rummel, Lisa; Kaus, Boris J. P.; White, Richard W.; Mertz, Dieter F.; Yang, Jianfeng; Baumann, Tobias S.

2018-01-01

Self-consistent geodynamic modeling that includes melting is challenging as the chemistry of the source rocks continuously changes as a result of melt extraction. Here, we describe a new method to study the interaction between physical and chemical processes in an uprising heterogeneous mantle plume by combining a geodynamic code with a thermodynamic modeling approach for magma generation and evolution. We pre-computed hundreds of phase diagrams, each of them for a different chemical system. After melt is extracted, the phase diagram with the closest bulk rock chemistry to the depleted source rock is updated locally. The petrological evolution of rocks is tracked via evolving chemical compositions of source rocks and extracted melts using twelve oxide compositional parameters. As a result, a wide variety of newly generated magmatic rocks can in principle be produced from mantle rocks with different degrees of depletion. The results show that a variable geothermal gradient, the amount of extracted melt and plume excess temperature affect the magma production and chemistry by influencing decompression melting and the depletion of rocks. Decompression melting is facilitated by a shallower lithosphere-asthenosphere boundary and an increase in the amount of extracted magma is induced by a lower critical melt fraction for melt extraction and/or higher plume temperatures. Increasing critical melt fractions activates the extraction of melts triggered by decompression at a later stage and slows down the depletion process from the metasomatized mantle. Melt compositional trends are used to determine melting related processes by focusing on K2O/Na2O ratio as indicator for the rock type that has been molten. Thus, a step-like-profile in K2O/Na2O might be explained by a transition between melting metasomatized and pyrolitic mantle components reproducible through numerical modeling of a heterogeneous asthenospheric mantle source. A potential application of the developed method is shown for the West Eifel volcanic field.

Rapid Passage of a Small-Scale Mantle Heterogeneity Through the Melting Regions of Kilauea and Mauna Loa Volcanoes

NASA Astrophysics Data System (ADS)

Pietruszka, A. J.; Marske, J. P.; Weis, D.; Garcia, M. O.; Rhodes, J. M.

2006-12-01

There are few quantitative estimates for the size, shape, and distribution of small-scale compositional heterogeneities within the Hawaiian mantle plume. The chemistry of recent lavas from the two most active Hawaiian volcanoes, Kilauea and Mauna Loa, provide a snapshot of the heterogeneous structure of the plume beneath Hawaii. We present Pb and Sr isotope ratios of two suites of young prehistoric lavas from these volcanoes: (1) Kilauea lavas from AD 1000 to 1500, and (2) 14C-dated Mauna Loa flows from ~2,650- 140 years BP. Prior to this study, the Pb and Sr isotope ratios of lavas from these volcanoes were thought to be completely distinct (e.g., Abouchami et al., 2005). However, these prehistoric Kilauea and Mauna Loa lavas display a systematic isotopic fluctuation, and the Kilauea lavas (in particular) span the Pb and Sr isotopic divide that was previously thought to exist between these two volcanoes. For a brief period from AD 250 to 1500, the Pb and Sr isotope ratios of Kilauea and Mauna Loa lavas departed from values typical for each volcano's historical period, moved towards a common isotopic composition, and subsequently, returned to more typical values. This transient magmatic event was probably caused by the rapid passage of a small-scale compositional heterogeneity though the melting regions of these volcanoes. The heterogeneity is thought to be either a single body that extends between the summits of both Kilauea and Mauna Loa (~35 km long) or the ubiquitous plume matrix itself. The time scale of this event (centuries) is much shorter than previously noted for variations in the isotopic composition of Hawaiian lavas due to the upwelling of heterogeneities within the plume (thousands to tens of thousands of years; Blichert-Toft et al., 2003; Kurz et al., 2004). Calculations based on the duration of the isotopic excursion suggest a maximum thickness for the melting region (and thus, the heterogeneity) of only ~5-10 km.

Observations of cloud chemistry during longrange transport of power plant plumes

NASA Astrophysics Data System (ADS)

Clark, P. A.; Fletcher, I. S.; Kallend, A. S.; McElroy, W. J.; Marsh, A. R. W.; Webb, A. H.

Measurements of the chemical composition of cloud water have been made as part of a programme to study the chemical development of power plant plumes in trajectories over the North Sea. During a two-day study (28-29 January 1981), the conditions were anticyclonic with light winds advecting the plume from the NE coast of England towards Denmark. The mixing layer overland was capped by stratocumulus beneath a very strong subsidence inversion, which resulted in the plume being entirely trapped within the layer. Low level acceleration occurred as the plume travelled towards the coast, accompanied by a shallowing of the mixing layer. This led to the unusual situation whereby the plume was confined to a shallow (400m) stratocumulus-filled boundary layer throughout most of its travel. The light winds enabled approximately Lagrangian sampling of the plume after about 5 and 22 h travel (~ 100 and 650km from source). The very shallow boundary layer constrained the dilution of the plume to such an extent that even though ambient O 3 was consumed within the plume by the reaction with NO, the NO 2/NO x ratio was still < 0.5 along the plume centre line after 22 h travel. The measurements have been compared with the predictions of a reactive plume model involving both gas phase and solution phase chemistry. The model predicts oxidation rates for SO 2 in the ambient air outside the plume to be substantially higher than those within the plume, at values of 0.5-1.0 and ~ 0.04 % h -1, respectively. This leads to the conclusion that nearly all the sulphate in the plume arose from entrainment of sulphate produced in cloud droplets outside the plume. The absence of an effective oxidation mechanism in solution for the conversion of NOx to HNO 3 suggests that nitrate in the cloud water was derived from the gas phase oxidation of NOx. HC1 was found to be the major contributor to cloud water acidity in the plume on this occasion. The resultant acidity suppressed the solubility of SO 2 and this together with the low oxidant levels inhibited the production of sulphate in solution within the plume. The HCl contribution to acidity had declined markedly after 22h travel and this loss corresponds to a dry deposition velocity of 13 mm s -1.

Dynamics of thermal plumes in three-dimensional isoviscous thermal convection

NASA Astrophysics Data System (ADS)

Zhong, Shijie

2005-07-01

The dynamics of mantle plumes are important for understanding intraplate volcanism and heat transfer in the mantle. Using 3-D numerical models and scaling analyses, we investigated the controls of convective vigour or Ra (Rayleigh number) on the dynamics of thermal plumes in isoviscous and basal heating thermal convection. We examined the Ra dependence of plume number, plume spacing, plume vertical velocity and plume radius. We found that plume number does not increase monotonically with Ra. At relatively small Ra(<=106), plume number is insensitive to Ra. For 3 × 106<=Ra<= 3 × 107, plume number scales as Ra0.31 and plume spacing λ~Ra-0.16~δ1/2, where δ is the thickness of the thermal boundary layer. However, for larger Ra(~108) plume number and plume spacing again become insensitive to Ra. This indicates that the box depth poses a limit on plume spacing and plume number. We demonstrate from both scaling analyses and numerical experiments that the scaling exponents for plume number, n, heat flux, β, and average velocity on the bottom boundary, v, satisfy n= 4β- 2v. Our scaling analyses also suggest that vertical velocity in upwelling plumes Vup~Ra2(1-n+β/2)/3 and that plume radius Rup~Ra(β-1-n/2)/3, which differ from the scalings for the bottom boundary velocity and boundary layer thickness.

Al-in-olivine thermometry evidence for the mantle plume origin of the Emeishan large igneous province

NASA Astrophysics Data System (ADS)

Xu, Rong; Liu, Yongsheng

2016-12-01

The Emeishan large igneous province (ELIP) is renowned for its world-class Ni-Cu-(PGE) deposits and its link with the Capitanian mass extinction. The ELIP is generally thought to be associated with a deep mantle plume; however, evidence for such a model has been challenged through geology, geophysics and geochemistry. In many large igneous province settings, olivine-melt equilibrium thermometry has been used to argue for or against the existence of plumes. However, this method involves large uncertainties such as assumptions regarding melt compositions and crystallisation pressures. The Al-in-olivine thermometer avoids these uncertainties and is used here to estimate the temperatures of picrites in the ELIP. The calculated maximum temperature (1440 °C) is significantly ( 250 °C) higher than the Al-in-olivine temperature estimated for the average MORB, thus providing compelling evidence for the existence of thermal mantle plumes in the ELIP.

Effects of entrained water and strong turbulence on afterburning within solid rocket motor plumes

NASA Technical Reports Server (NTRS)

Gomberg, R. I.; Wilmoth, R. G.

1978-01-01

During the first few seconds of the space shuttle trajectory, the solid rocket boosters will be in the proximity of the launch pad. Because of the launch pad structures and the surface of the earth, the turbulent mixing experienced by the exhaust gases will be greatly increased over that for the free flight situation. In addition, a system will be present, designed to protect the lifting vehicle from launch structure vibrations, which will inject quantities of liquid water into the hot plume. The effects of these two phenomena on the temperatures, chemical composition, and flow field present in the afterburning solid rocket motor exhaust plumes of the space shuttle were studied. Results are included from both a computational model of the afterburning and supporting measurements from Titan 3 exhaust plumes taken at Kennedy Space Center with infrared scanned radiometers.

Chloroethene dechlorination in acidic groundwater: Implications for combining fenton's treatment with natural attenuation

USGS Publications Warehouse

Bradley, Paul M.; Singletary , Michael A.; Chapelle, Francis H.

2007-01-01

A sulfuric acid leak in 1988 at a chloroethene-contaminated groundwater site at the Naval Air Station Pensacola has resulted in a long-term record of the behavior of chloroethene contaminants at low pH and a unique opportunity to assess the potential impact of source area treatment technologies, which involve acidification of the groundwater environment (e.g., Fenton's-based in situ chemical oxidation), on downgradient natural attenuation processes. The greater than 75 percent decrease in trichloroethene (TCE) concentrations and the shift in contaminant composition toward predominantly reduced daughter products (dichloroethene [DCE] and vinyl chloride [VC]) that were observed along a 30-m groundwater flow path characterized by highly acidic conditions (pH = 3.5 ± 0.4) demonstrated that chloroethene reductive dechlorination can continue to be efficient under persistent acidic conditions. The detection of Dehalococcoides-type bacteria within the sulfuric acid/chloroethene co-contaminant plume was consistent with biotic chloroethene reductive dechlorination. Microcosm studies conducted with 14C-TCE and 14C-VC confirmed biotic reductive dechlorination in sediment collected from within the sulfuric acid/chloroethene co-contaminant plume. Microcosms prepared with sediment from two other locations within the acid plume, however, demonstrated only a limited mineralization to 14CO2 and 14CO, which was attributed to abiotic degradation because no significant differences were observed between experimental and autoclaved control treatments. These results indicated that biotic and abiotic mechanisms contributed to chloroethene attenuation in the acid plume at NAS Pensacola and that remediation techniques involving acidification of the groundwater environment (e.g., Fenton's-based source area treatment) do not necessarily preclude efficient chloroethene degradation.

Evolution of the East African rift: Drip magmatism, lithospheric thinning and mafic volcanism

NASA Astrophysics Data System (ADS)

Furman, Tanya; Nelson, Wendy R.; Elkins-Tanton, Linda T.

2016-07-01

The origin of the Ethiopian-Yemeni Oligocene flood basalt province is widely interpreted as representing mafic volcanism associated with the Afar mantle plume head, with minor contributions from the lithospheric mantle. We reinterpret the geochemical compositions of primitive Oligocene basalts and picrites as requiring a far more significant contribution from the metasomatized subcontinental lithospheric mantle than has been recognized previously. This region displays the fingerprints of mantle plume and lithospheric drip magmatism as predicted from numerical models. Metasomatized mantle lithosphere is not dynamically stable, and heating above the upwelling Afar plume caused metasomatized lithosphere with a significant pyroxenite component to drip into the asthenosphere and melt. This process generated the HT2 lavas observed today in restricted portions of Ethiopia and Yemen now separated by the Red Sea, suggesting a fundamental link between drip magmatism and the onset of rifting. Coeval HT1 and LT lavas, in contrast, were not generated by drip melting but instead originated from shallower, dominantly anhydrous peridotite. Looking more broadly across the East African Rift System in time and space, geochemical data support small volume volcanic events in Turkana (N. Kenya), Chyulu Hills (S. Kenya) and the Virunga province (Western Rift) to be derived ultimately from drip melting. The removal of the gravitationally unstable, metasomatized portion of the subcontinental lithospheric mantle via dripping is correlated in each case with periods of rapid uplift. The combined influence of thermo-mechanically thinned lithosphere and the Afar plume together thus controlled the locus of continental rift initiation between Africa and Arabia and provide dynamic support for the Ethiopian plateau.

Iron budgets for three distinct biogeochemical sites around the Kerguelen archipelago (Southern Ocean) during the natural fertilisation experiment KEOPS-2

NASA Astrophysics Data System (ADS)

Bowie, A. R.; van der Merwe, P.; Quéroué, F.; Trull, T.; Fourquez, M.; Planchon, F.; Sarthou, G.; Chever, F.; Townsend, A. T.; Obernosterer, I.; Sallée, J.-B.; Blain, S.

2014-12-01

Iron availability in the Southern Ocean controls phytoplankton growth, community composition and the uptake of atmospheric CO2 by the biological pump. The KEOPS-2 experiment took place around the Kerguelen plateau in the Indian sector of the Southern Ocean, a region naturally fertilised with iron at the scale of hundreds to thousands of square kilometres, producing a mosaic of spring blooms which showed distinct biological and biogeochemical responses to fertilisation. This paper presents biogeochemical iron budgets (incorporating vertical and lateral supply, internal cycling, and sinks) for three contrasting sites: an upstream high-nutrient low-chlorophyll reference, over the plateau, and in the offshore plume east of Kerguelen Island. These budgets show that distinct regional environments driven by complex circulation and transport pathways are responsible for differences in the mode and strength of iron supply, with vertical supply dominant on the plateau and lateral supply dominant in the plume. Iron supply from "new" sources to surface waters of the plume was double that above the plateau and 20 times greater than at the reference site, whilst iron demand (measured by cellular uptake) in the plume was similar to the plateau but 40 times greater than the reference. "Recycled" iron supply by bacterial regeneration and zooplankton grazing was a relative minor component at all sites (<8% of "new" supply), in contrast to earlier findings from other biogeochemical iron budgets in the Southern Ocean. Over the plateau, a particulate iron dissolution term of 2.5% was invoked to balance the budget; this approximately doubled the standing stock of dissolved iron in the mixed layer. The exchange of iron between dissolved, biogenic and lithogenic particulate pools was highly dynamic in time and space, resulting in a decoupling of iron supply and carbon export and, importantly, controlling the efficiency of fertilisation.

Iron budgets for three distinct biogeochemical sites around the Kerguelen Archipelago (Southern Ocean) during the natural fertilisation study, KEOPS-2

NASA Astrophysics Data System (ADS)

Bowie, A. R.; van der Merwe, P.; Quéroué, F.; Trull, T.; Fourquez, M.; Planchon, F.; Sarthou, G.; Chever, F.; Townsend, A. T.; Obernosterer, I.; Sallée, J.-B.; Blain, S.

2015-07-01

Iron availability in the Southern Ocean controls phytoplankton growth, community composition and the uptake of atmospheric CO2 by the biological pump. The KEOPS-2 (KErguelen Ocean and Plateau compared Study 2) "process study", took place around the Kerguelen Plateau in the Indian sector of the Southern Ocean. This is a region naturally fertilised with iron on the scale of hundreds to thousands of square kilometres, producing a mosaic of spring blooms which show distinct biological and biogeochemical responses to fertilisation. This paper presents biogeochemical iron budgets (incorporating vertical and lateral supply, internal cycling, and sinks) for three contrasting sites: an upstream high-nutrient low-chlorophyll reference, over the plateau and in the offshore plume east of the Kerguelen Islands. These budgets show that distinct regional environments driven by complex circulation and transport pathways are responsible for differences in the mode and strength of iron supply, with vertical supply dominant on the plateau and lateral supply dominant in the plume. Iron supply from "new" sources (diffusion, upwelling, entrainment, lateral advection, atmospheric dust) to the surface waters of the plume was double that above the plateau and 20 times greater than at the reference site, whilst iron demand (measured by cellular uptake) in the plume was similar to that above the plateau but 40 times greater than at the reference site. "Recycled" iron supply by bacterial regeneration and zooplankton grazing was a relatively minor component at all sites (< 8 % of new supply), in contrast to earlier findings from other biogeochemical iron budgets in the Southern Ocean. Over the plateau, a particulate iron dissolution term of 2.5 % was invoked to balance the budget; this approximately doubled the standing stock of dissolved iron in the mixed layer. The exchange of iron between dissolved, biogenic particulate and lithogenic particulate pools was highly dynamic in time and space, resulting in a decoupling of the iron supply and carbon export and, importantly, controlling the efficiency of fertilisation.

Characteristics of chiral plasma plumes generated in the absence of external magnetic field

NASA Astrophysics Data System (ADS)

Nie, LanLan; Liu, FengWu; Zhou, XinCai; Lu, XinPei; Xian, YuBin

2018-05-01

A chiral plasma plume has recently been generated inside a dielectric tube without the use of an external magnetic field. In this paper, we seek to further study the key properties of such a chiral plume to improve our understanding of how this interesting structure is generated and controlled. The chiral plume is generated by externally mounting a stainless steel helical coil or a ring onto the dielectric tube. By changing the pitch of the helical coil, the pitch of the plasma plume can be controlled, with the shape of the plume following the shape of the helical coil. The addition of the helical coil significantly expands the range of parameters under which the chiral plasma plume appears. When the frequency of the applied voltage increases, additional stable discharge channels appear between the adjacent helices. The addition of two helical coils results in the formation of two chiral plasma plumes, which follow the shape of the helical coils. When a metal ring is placed on the outside of the tube, there is no chiral plasma plume between the high voltage electrode and the ring; however, a chiral plasma plume appears on the right side of the ring if the distance between the ring and the high voltage electrode is small. These findings suggest that the chiral plasma can be effectively modulated and guided using an externally mounted helical coil, which acts as the floating/actual ground to reduce the impedance of the discharge and as such contributes to the emergence of the chiral plasma plume behavior.

Modeling the Complex Photochemistry of Biomass Burning Plumes in Plume-Scale, Regional, and Global Air Quality Models

NASA Astrophysics Data System (ADS)

Alvarado, M. J.; Lonsdale, C. R.; Yokelson, R. J.; Travis, K.; Fischer, E. V.; Lin, J. C.

2014-12-01

Forecasting the impacts of biomass burning (BB) plumes on air quality is difficult due to the complex photochemistry that takes place in the concentrated young BB plumes. The spatial grid of global and regional scale Eulerian models is generally too large to resolve BB photochemistry, which can lead to errors in predicting the formation of secondary organic aerosol (SOA) and O3, as well as the partitioning of NOyspecies. AER's Aerosol Simulation Program (ASP v2.1) can be used within plume-scale Lagrangian models to simulate this complex photochemistry. We will present results of validation studies of the ASP model against aircraft observations of young BB smoke plumes. We will also present initial results from the coupling of ASP v2.1 into the Lagrangian particle dispersion model STILT-Chem in order to better examine the interactions between BB plume chemistry and dispersion. In addition, we have used ASP to develop a sub-grid scale parameterization of the near-source chemistry of BB plumes for use in regional and global air quality models. The parameterization takes inputs from the host model, such as solar zenith angle, temperature, and fire fuel type, and calculates enhancement ratios of O3, NOx, PAN, aerosol nitrate, and other NOy species, as well as organic aerosol (OA). We will present results from the ASP-based BB parameterization as well as its implementation into the global atmospheric composition model GEOS-Chem for the SEAC4RS campaign.

Probing the Hawaiian Hot Spot With New Broadband Ocean Bottom Instruments

NASA Astrophysics Data System (ADS)

Laske, Gabi; Collins, John A.; Wolfe, Cecily J.; Solomon, Sean C.; Detrick, Robert S.; Orcutt, John A.; Bercovici, David; Hauri, Erik H.

2009-10-01

The Hawaiian hot spot is regarded as the textbook example of the product of a deep-rooted mantle plume [Wilson, 1963; Morgan, 1971]. Its isolated location, far from any plate boundary, should provide an opportunity to test most basic hypotheses on the nature of plume-plate interaction and related magmatism [e.g., Ribe and Christensen, 1999]. Yet the lack of crucial geophysical data has sustained a debate about whether Hawaii's volcanism is plume-related or is instead the consequence of more shallow processes, such as the progressive fracturing of the plate in response to extensional stresses [Turcotte and Oxburgh, 1973]. In the plume model for Hawaii's volcanism, hot material is expected to ascend near vertically within the more viscous surrounding mantle before ponding and spreading laterally beneath the rigid lithosphere. Mantle convection in general, and the fast moving Pacific plate in particular, shear and tilt the rising plume. The plume top is dragged downstream by the plate, and this dragged material may give rise to an elongated bathymetric swell [Davies, 1988; Olson, 1990; Sleep, 1990; Phipps Morgan et al., 1995]. However, identifying the dominant cause of the swell remains elusive, and proposed mechanisms include thermal rejuvenation, dynamic support, compositional buoyancy, and mechanical erosion (see Li et al. [2004] for a summary). There is also considerable debate about the continuity of the plume within the mantle, how discrete islands are formed, and how a deep-rooted plume interacts with the mantle transition zone [e.g., van Keken and Gable, 1995].

Linking Europa’s Plume Activity to Tides, Tectonics, and Liquid Water

NASA Astrophysics Data System (ADS)

Rhoden, Alyssa R.; Hurford, Terry; Roth, Lorenz; Retherford, Kurt

2014-11-01

Much of the geologic activity preserved on Europa’s icy surface has been attributed to tidal deformation, mainly due to Europa’s eccentric orbit. Although the surface is geologically young, evidence of ongoing tidally-driven processes has been lacking. However, a recent observation of water vapor near Europa’s south pole suggests that it may be geologically active. Non-detections in previous and follow-up observations indicate a temporal variation in plume visibility and suggests a relationship to Europa’s tidal cycle. Similarly, the Cassini spacecraft has observed plumes emanating from the south pole of Saturn’s moon, Enceladus, and variability in the intensity of eruptions has been linked to its tidal cycle. The inference that a similar mechanism controls plumes at both Europa and Enceladus motivates further analysis of Europa’s plume behavior and the relationship between plumes, tides, and liquid water on these two satellites.We determine the locations and orientations of hypothetical tidally-driven fractures that best match the temporal variability of the plumes observed at Europa. Specifically, we identify model faults that are in tension at the time in Europa’s orbit when a plume was detected and in compression at times when the plume was not detected. We find that tidal stress driven solely by eccentricity is incompatible with the observations unless additional mechanisms are controlling the eruption timing or restricting the longevity of the plumes. In contrast, the addition of obliquity tides, and corresponding precession of the spin pole, can generate a number of model faults that are consistent with the pattern of plume detections. The locations and orientations of the model faults are robust across a broad range of precession rates and spin pole directions. Analysis of the stress variations across model faults suggests that the plumes would be best observed earlier in Europa’s orbit. Our results indicate that Europa’s plumes, if confirmed, differ in many respects from the Enceladean plumes and that either active fractures or volatile sources are rare.

Modeling nucleation and coagulation modes in the formation of particulate matter inside a turbulent exhaust plume of a diesel engine.

PubMed

Kim, Dong-Hee; Gautam, Mridul; Gera, Dinesh

2002-05-01

This paper presents the results from a study that is aimed at predicting the nucleation, coagulation, and dynamics of particulate matter (PM) emissions from on-road heavy-duty diesel vehicles. The PM concentration is predicted from the composition of fuel, and operating and ambient conditions. A numerical algorithm for simultaneously solving the coagulation, condensation, and nucleation equations is developed. The effect of relative humidity on the nucleation rate and the nucleus size is also discussed. In addition, the effect of the ambient air dilution on PM size distribution is numerically predicted for a diesel-powered truck operating in a controlled environment at NASA Langley wind-tunnel facility. The particle size distribution and concentration are measured at four different locations in a turbulent plume from the diesel exhaust in the tunnel, and an excellent agreement between the measured and predicted PM concentration values at these locations inside the tunnel is observed.

Lack of Correlated Isotopic and Compositional Variations in Mauna Loa Lavas: A Serious Problem for Pyroxenite/Eclogite Plume Source Models

NASA Astrophysics Data System (ADS)

Rhodes, J. M.; Weis, D.; Norman, M. D.; Garcia, M. O.

2007-12-01

The long held notion that basaltic magmas are produced by decompressional melting of peridotite is under challenge. Recent models for the Hawaiian and other plumes argue that they consist of a heterogeneous mix of peridotite and discrete eclogite blobs, the latter derived from recycled subducted crust. Eclogite melting produces relatively siliceous magmas (dacite to andesite) which either mix with picritic melts from the peridotite, or, more plausibly, react with the peridotite to produce pyroxenite. Melting of varying proportions of the peridotite/pyroxenite mix is thought to produce the correlated compositional and isotopic characteristics of Hawaiian volcanoes. Magmas from Mauna Loa and Koolau volcanoes are thought to contain more of the recycled component; those from Loihi and Kilauea volcanoes contain less. A simple test of these mixed source models examines whether isotopic changes within the long magmatic history of a single volcano are accompanied by corresponding changes in major and trace element characteristics. Mauna Loa, where we have sampled around 400 - 500 ka of the volcano's eruptive history, provides an excellent opportunity for such a test. During this time, Mauna Loa will have traversed almost half the Hawaiian plume. According to the models, it should have erupted magmas produced from a range of pyroxenite/peridotite mixes with corresponding differences in both isotopic ratios and major and trace elements. Our data show that there is only minor isotopic (Sr, Pb, Nd, Hf) diversity in young lavas (<100 ka), but older lavas are highly diverse, ranging from modern values to those that are close to, and overlap with, those of Loihi volcano. If this isotopic diversity is a consequence of different proportions of pyroxenite and peridotite in the plume source, as the new models predict, we should expect to see correlated changes in bulk composition, particularly. in normalized SiO2, CaO/Al2O3, FeO/MgO and Ni - MgO relationships, as well as changes in Ni - Sc - V relationships. We do not. These parameters remain remarkably uniform over the 400 to 500 ka magmatic history of the volcano, with no correlated variation with isotopic ratios. We conclude that the isotopic heterogeneity within the Hawaiian plume is intrinsic to the peridotite plume source and not dependent on variable contributions from entrained, lithologically-discrete units.

Performance, Stability, and Plume Characterization of the HERMeS Thruster with Boron Nitride Silica Composite Discharge Channel

NASA Technical Reports Server (NTRS)

Kamhawi, Hani; Huang, Wensheng; Gilland, James H.; Haag, Thomas W.; Mackey, Jonathan; Yim, John; Pinero, Luis; Williams, George; Peterson, Peter; Herman, Daniel

2017-01-01

NASA's Hall Effect Rocket with Magnetic Shielding (HERMeS) 12.5kW Technology Demonstration Unit-3 (TDU-3) has been the subject of extensive technology maturation in preparation for flight system development. Detailed performance, stability, and plume characterization tests of the thruster were performed at NASA GRC's Vacuum Facility 5 (VF-5). The TDU-3 thruster implements a magnetic topology that is identical to TDU-1. The TDU-3 boron nitride silica composite discharge channel material is different than the TDU-1 heritage boron nitride discharge channel material. Performance and stability characterization of the TDU-3 thruster was performed at discharge voltages between 300V and 600V and at discharge currents between 5A and 21.8A. The thruster performance and stability were assessed for varying magnetic field strength, cathode flow fractions between 5% and 9%, varying harness inductance, and for reverse magnet polarity. Performance characterization test results indicate that the TDU-3 thruster performance is in family with the TDU-1 levels. TDU-3's thrust efficiency of 65% and specific impulse of 2,800sec at 600V and 12.5kW exceed performance levels of SOA Hall thrusters. Thruster stability regimes were characterized with respect to the thruster discharge current oscillations (discharge current peak-to-peak and root mean square magnitudes), discharge current waveform power spectral density analysis, and maps of the current-voltage-magnetic field. Stability characterization test results indicate a stability profile similar to TDU-1. Finally, comparison of the TDU-1 and TDU-3 plume profiles found that there were negligible differences in the plasma plume characteristics between the TDU with heritage boron nitride versus the boron nitride silica composite discharge channel.

A new method for GPS-based wind speed determinations during airborne volcanic plume measurements

USGS Publications Warehouse

Doukas, Michael P.

2002-01-01

Begun nearly thirty years ago, the measurement of gases in volcanic plumes is today an accepted technique in volcano research. Volcanic plume measurements, whether baseline gas emissions from quiescent volcanoes or more substantial emissions from volcanoes undergoing unrest, provide important information on the amount of gaseous output of a volcano to the atmosphere. Measuring changes in gas emission rates also allows insight into eruptive behavior. Some of the earliest volcanic plume measurements of sulfur dioxide were made using a correlation spectrometer (COSPEC). The COSPEC, developed originally for industrial pollution studies, is an upward-looking optical spectrometer tuned to the ultraviolet absorption wavelength of sulfur dioxide (Millán and Hoff, 1978). In airborne mode, the COSPEC is mounted in a fixed-wing aircraft and flown back and forth just underneath a volcanic plume, perpendicular to the direction of plume travel (Casadevall and others, 1981; Stoiber and others, 1983). Similarly, for plumes close to the ground, the COSPEC can be mounted in an automobile and driven underneath a plume if a suitable road system is available (Elias and others, 1998). The COSPEC can also be mounted on a tripod and used to scan a volcanic plume from a fixed location on the ground, although the effectiveness of this configuration declines with distance from the plume (Kyle and others, 1990). In the 1990’s, newer airborne techniques involving direct sampling of volcanic plumes with infrared spectrometers and electrochemical sensors were developed in order to measure additional gases such as CO2 and H2S (Gerlach and others, 1997; Gerlach and others, 1999; McGee and others, 2001). These methods involve constructing a plume cross-section from several measurement traverses through the plume in a vertical plane. Newer instruments such as open-path Fourier transform infrared (FTIR) spectrometers are now being used to measure the gases in volcanic plumes mostly from fixed locations on the ground. Most FTIR studies to date measure only gas compositions or ratios of gas species (Love and others, 1998; Francis and others, 1998; Horrocks and others, 1999). What all of these methods have in common, however, is the necessity to know plume velocities if accurate gas emission rates are to be calculated. Even open-path FTIR studies done in tandem with a COSPEC require knowledge of plume velocity in order to compute emission rates.

Rift-plume interaction reveals multiple generations of recycled oceanic crust in Azores lavas

NASA Astrophysics Data System (ADS)

Béguelin, Paul; Bizimis, Michael; Beier, Christoph; Turner, Simon

2017-12-01

We present 176Hf/177Hf isotope ratios on 41 previously well-characterized subaerial and submarine samples from the Azores islands of São Miguel, Terceira, Graciosa, Faial, Pico and the João de Castro seamount (on the Terceira Rift). In εNd-εHf isotope space all Azores lavas fall below the mantle array reference line and do not overlap the proximal Atlantic MORB. Lavas from São Miguel and João de Castro form two distinct and well defined arrays extending below the mantle array, which has not been previously documented in other oceanic magmatic provinces. The Nd-Hf isotope compositions of João de Castro overlap those of HIMU type lavas, yet they lack the characteristically radiogenic Pb isotope ratios of HIMU. The combined Nd-Hf-Pb-Sr isotope systematics of both São Miguel and João de Castro endmembers can be explained by recycling of a single package of heterogeneous oceanic crust ranging from D-MORB to E-MORB in composition, with an age between 2.5 and 3.0 Ga, with no requirement for parent-daughter ratio modification during subduction. In contrast the Nd-Hf-Pb isotope systematics of lavas from São Jorge, Terceira, Graciosa, Pico and Faial are consistent with the presence of younger (<700 Ma) recycled crust that underwent low-temperature alteration and dehydration during subduction. There is no evidence in the erupted lavas for direct mixing between these two generations of recycled material within the plume. These data suggest that old recycling age and absence of sediments along with recycled oceanic crust are both required to develop isotopic compositions below the mantle array in εNd-εHf space. Our modeling shows that the compositional variability of erupted MORB is large enough that, given enough time, they can generate a wide range of isotope compositions such as observed in OIB. Lastly, lava compositions along the Terceira rift can be explained by a westward asthenospheric flux along a tilted lithosphere/asthenosphere boundary, where fertile components are exhausted by partial melting after ∼70 km of transport along the Terceira Rift. While this observation is broadly consistent with the plume source-ridge sink model, it also suggests that the lithosphere/asthenosphere boundary geometry can smear the view of the plume heterogeneity.

Multiple volcanic episodes of flood basalts caused by thermochemical mantle plumes.

PubMed

Lin, Shu-Chuan; van Keken, Peter E

2005-07-14

The hypothesis that a single mushroom-like mantle plume head can generate a large igneous province within a few million years has been widely accepted. The Siberian Traps at the Permian-Triassic boundary and the Deccan Traps at the Cretaceous-Tertiary boundary were probably erupted within one million years. These large eruptions have been linked to mass extinctions. But recent geochronological data reveal more than one pulse of major eruptions with diverse magma flux within several flood basalts extending over tens of million years. This observation indicates that the processes leading to large igneous provinces are more complicated than the purely thermal, single-stage plume model suggests. Here we present numerical experiments to demonstrate that the entrainment of a dense eclogite-derived material at the base of the mantle by thermal plumes can develop secondary instabilities due to the interaction between thermal and compositional buoyancy forces. The characteristic timescales of the development of the secondary instabilities and the variation of the plume strength are compatible with the observations. Such a process may contribute to multiple episodes of large igneous provinces.

Observations of brine plumes below melting Arctic sea ice

NASA Astrophysics Data System (ADS)

Peterson, Algot K.

2018-02-01

In sea ice, interconnected pockets and channels of brine are surrounded by fresh ice. Over time, brine is lost by gravity drainage and flushing. The timing of salt release and its interaction with the underlying water can impact subsequent sea ice melt. Turbulence measurements 1 m below melting sea ice north of Svalbard reveal anticorrelated heat and salt fluxes. From the observations, 131 salty plumes descending from the warm sea ice are identified, confirming previous observations from a Svalbard fjord. The plumes are likely triggered by oceanic heat through bottom melt. Calculated over a composite plume, oceanic heat and salt fluxes during the plumes account for 6 and 9 % of the total fluxes, respectively, while only lasting in total 0.5 % of the time. The observed salt flux accumulates to 7.6 kg m-2, indicating nearly full desalination of the ice. Bulk salinity reduction between two nearby ice cores agrees with accumulated salt fluxes to within a factor of 2. The increasing fraction of younger, more saline ice in the Arctic suggests an increase in desalination processes with the transition to the new Arctic.

Quantifying the Intercontinental and Global Reach and Effects of Pollution

NASA Technical Reports Server (NTRS)

Chatfield, Robert B.; Guo, Zitan

2000-01-01

The Atmospheric Chemistry Modeling Group is participating in an international effort to explore the projected interactions of the atmosphere with biota, human activity, and the natural environment over the next three decades. The group uses computer simulations and statistical analyses to compare theory and observations of the composition of the lower atmosphere. This study of global habitability change is part of a more ambitious activity to understand global habitability. This broad planetary understanding is central to planetary habitability, biomarker detection, and similar aspects of Astrobiology. The group has made highly detailed studies of immense intercontinental plumes that affect the chemistry of the global atmosphere, especially the region below the ozone (O3) layer whose chemical composition defines the conditions for healthy humans and the biosphere. For some decades there has been concern about the pollution from cities and industrial burning and its possible effect in increasing smog ozone, not only in continental regions, but also in plumes that spread downwind. Recently, there has been new concern about another kind of pollution plume. Projections for a greatly expanded aircraft fleet imply that there will be plumes of nitrogen oxides (NO(x)) from jet exhaust in the Northern Hemisphere downwind of major air traffic routes. Both of these are tied to large-scale O3 in the troposphere, where it is toxic to humans and plant tissues.

RELATIVE ABUNDANCE MEASUREMENTS IN PLUMES AND INTERPLUMES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guennou, C.; Hahn, M.; Savin, D. W., E-mail: cguennou@iac.es

2015-07-10

We present measurements of relative elemental abundances in plumes and interplumes. Plumes are bright, narrow structures in coronal holes that extend along open magnetic field lines far out into the corona. Previous work has found that in some coronal structures the abundances of elements with a low first ionization potential (FIP) <10 eV are enhanced relative to their photospheric abundances. This coronal-to-photospheric abundance ratio, commonly called the FIP bias, is typically 1 for elements with a high-FIP (>10 eV). We have used Extreme Ultraviolet Imaging Spectrometer observations made on 2007 March 13 and 14 over a ≈24 hr period tomore » characterize abundance variations in plumes and interplumes. To assess their elemental composition, we used a differential emission measure analysis, which accounts for the thermal structure of the observed plasma. We used lines from ions of iron, silicon, and sulfur. From these we estimated the ratio of the iron and silicon FIP bias relative to that for sulfur. From the results, we have created FIP-bias-ratio maps. We find that the FIP-bias ratio is sometimes higher in plumes than in interplumes and that this enhancement can be time dependent. These results may help to identify whether plumes or interplumes contribute to the fast solar wind observed in situ and may also provide constraints on the formation and heating mechanisms of plumes.« less

Seismic anisotropy and compositionally induced velocity anomalies in the lithosphere above mantle plumes: a petrological and microstructural study of mantle xenoliths from French Polynesia

NASA Astrophysics Data System (ADS)

Tommasi, Andréa; Godard, Marguerite; Coromina, Guilhem; Dautria, Jean-Marie; Barsczus, Hans

2004-11-01

In addition to thermal erosion, plume/lithosphere interaction may induce significant changes in the lithosphere chemical composition. To constrain the extent of this process in an oceanic environment and its consequences on the lithosphere seismic properties, we investigated the relationship between petrological processes and microstructure in mantle xenoliths from different hotspots tracks in South Pacific Superswell region: the Austral-Cook, Society, and Marquesas islands in French Polynesia. Olivine forsterite contents in the studied spinel peridotites vary continuously from Fo91 to Fo83. Dunites and wehrlites display the lowest forsterite contents. Their microstructure and high Ni contents preclude a cumulate origin, suggesting that these rocks result from melt/rock reactions involving olivine precipitation and pyroxene dissolution. In addition, lherzolites and wehrlites display evidence of late crystallization of clinopyroxene, which may result from a near-solidus melt-freezing reaction. These data suggest that the lithosphere above a mantle plume undergoes a complex sequence of magmatic processes that significantly change its composition. These compositional changes, particularly iron enrichment in olivine, result in lower P- and S-waves velocities. Relative to normal lithospheric mantle, compositionally induced seismic anomalies may attain -2.2% for S-waves and -1% for P-waves. Smaller negative anomalies for P-waves are due to a higher sensitivity to modal composition. Conversely, crystal-preferred orientations (CPO) and seismic anisotropy are little affected by these processes. Lherzolites and harzburgites, independent from composition, show high-temperature porphyroclastic microstructures and strong olivine CPO. Dunites and wehrlites display annealing microstructures to which is associated a progressive dispersion of the olivine CPO. Very weak, almost random olivine CPO is nevertheless rare, suggesting that CPO destruction is restricted to domains of intense magma-rock interaction due to localized flow or accumulation of magmas.

Trace element and Sr-Nd-Pb isotope geochemistry of Rungwe Volcanic Province, Tanzania: Implications for a superplume source for East Africa Rift magmatism

NASA Astrophysics Data System (ADS)

Castillo, Paterno; Hilton, David; Halldórsson, Sæmundur

2014-09-01

The recently discovered high, plume-like 3He/4He ratios at Rungwe Volcanic Province (RVP) in southern Tanzania, similar to those at the Main Ethiopian Rift in Ethiopia, strongly suggest that magmatism associated with continental rifting along the entire East African Rift System (EARS) has a deep mantle contribution (Hilton et al., 2011). New trace element and Sr-Nd-Pb isotopic data for high 3He/4He lavas and tephras from RVP can be explained by binary mixing relationships involving Early Proterozoic (+/- Archaean) lithospheric mantle, present beneath the southern EARS, and a volatile-rich carbonatitic plume with a limited range of compositions and best represented by recent Nyiragongo lavas from the Virunga Volcanic Province also in the Western Rift. Other lavas from the Western Rift and from the southern Kenya Rift can also be explained through mixing between the same endmember components. In contrast, lavas from the northern Kenya and Main Ethiopian rifts can be explained through variable mixing between the same mantle plume material and the Middle to Late Proterozoic lithospheric mantle, present beneath the northern EARS. Thus, we propose that the bulk of EARS magmatism is sourced from mixing among three endmember sources: Early Proterozoic (+/- Archaean) lithospheric mantle, Middle to Late Proterozoic lithospheric mantle and a volatile-rich carbonatitic plume with a limited range of compositions. We propose further that the African Superplume, a large, seismically anomalous feature originating in the lower mantle beneath southern Africa, influences magmatism throughout eastern Africa with magmatism at RVP and Main Ethiopian Rift representing two different heads of a single mantle plume source. This is consistent with a single mantle plume origin of the coupled He-Ne isotopic signatures of mantle-derived xenoliths and/or lavas from all segments of the EARS (Halldorsson et al., 2014).

Direct stratospheric injection of biomass burning emissions: a case study of the 2009 Australian bushfires using the NASA GISS ModelE2 composition-climate model

NASA Astrophysics Data System (ADS)

Field, Robert; From, Mike; Voulgarakis, Apostolos; Shindell, Drew; Flannigan, Mike; Bernath, Peter

2014-05-01

Direct stratospheric injection (DSI) of forest fire smoke represents a direct biogeochemical link between the land surface and stratosphere. DSI events occur regularly in the northern and southern extratropics, and have been observed across a wide range of measurements, but their fate and effects are not well understood. DSIs result from explosive, short-lived fires, and their plumes stand out from background concentrations immediately. This makes it easier to associate detected DSIs to individual fires and their estimated emissions. Because the emissions pulses are brief, chemical decay can be more clearly assessed, and because the emissions pulses are so large, a wide range of rare chemical species can be detected. Observational evidence suggests that they can persist in the stratosphere for several months, enhance ozone production, and be self-lofted to the middle stratosphere through shortwave absorption and diabatic heating. None of these phenomena have been evaluated, however, with a physical model. To that end, we are simulating the smoke plumes from the February 2009 Australia 'Black Saturday' bushfires using the NASA GISS ModelE2 composition-climate model, nudged toward horizontal winds from reanalysis. To-date, this is the best-observed DSI in the southern hemisphere. Chemical and aerosol signatures of the plume were observed in a wide array of limb and nadir satellite retrievals. Detailed estimates of fuel consumption and injection height have been made because of the severity of the fires. Uncommon among DSIs events was a large segment of the plume that entrained into the upper equatorial easterlies. Preliminary modeling results show that the relative strengths of the equatorial and extratropical plume segments are sensitive to the plume's initial injection height. This highlights the difficulty in reconciling uncertainty in the reanalysis over the Southern Hemisphere with fairly-well constrained estimates of fire location and injection height at the source.

Chemical composition of fine particles in fresh smoke plumes from boreal wild-land fires in Europe.

PubMed

Saarnio, Karri; Aurela, Minna; Timonen, Hilkka; Saarikoski, Sanna; Teinilä, Kimmo; Mäkelä, Timo; Sofiev, Mikhail; Koskinen, Jarkko; Aalto, Pasi P; Kulmala, Markku; Kukkonen, Jaakko; Hillamo, Risto

2010-05-15

A series of smoke plumes was detected in Helsinki, Finland, during a one-month-lasting period in August 2006. The smoke plumes originated from wildfires close to Finland, and they were short-term and had a high particulate matter (PM) concentration. Physical and chemical properties of fine particles in those smokes were characterised by a wide range of real-time measurements that enabled the examination of individual plume events. Concurrently PM(1) filter samples were collected and analysed off-line. Satellite observations employing MODIS sensor on board of NASA EOS Terra satellite with the dispersion model SILAM and the Fire Assimilation System were used for evaluation of the emission fluxes from wildfires. The model predicted well the timing of the plumes but the predicted PM concentrations differed from the observed. The measurements showed that the major growth in PM concentration was caused by submicrometer particles consisting mainly of particulate organic matter (POM). POM had not totally oxidised during the transport based on the low WSOC-to-OC ratio. The fresh plumes were compared to another major smoke episode that was observed in Helsinki during April-May 2006. The duration and the source areas of the two episode periods differed. The episode in April-May was a period of nearly constantly upraised level of long-range transported PM and it was composed of aged particles when arriving in Helsinki. The two episodes had differences also in the chemical composition of PM. The mass concentrations of biomass burning tracers (levoglucosan, potassium, and oxalate) increased during both the episodes but different concentration levels of elemental carbon and potassium indicated that the episodes differed in the form of burning as well as in the burning material. In spring dry crop residue and hay from the previous season were burnt whereas in August smokes from smouldering and incomplete burning of fresh vegetation were detected. Copyright 2010 Elsevier B.V. All rights reserved.

Mapping of plume deposits and surface composition on Enceladus

NASA Astrophysics Data System (ADS)

Nordheim, T. A.; Scipioni, F.; Cruikshank, D. P.; Clark, R. N.,; Hand, K. P.

2017-01-01

A major result of the Cassini mission was the discovery that the small mid-sized moon Enceladus is presently geological active[Dougherty et al., 2006; Porco et al., 2006; Spencer et al., 2006; Hansen et al., 2008]. This activity results in plumes of water vapor and ice emanating from a series of fractures ("Tiger Stripes") at the moon's South Pole. Some fraction of plume material escapes the moon's gravity and populates the E-ring as well as ultimately providing a source of fresh plasma in the Saturnian magnetosphere [Pontius and Hill, 2006; Kempf et al., 2010]. However, a significant portion of plume material is redeposited on Enceladus and thus provides a source of surface contaminants. By studying the near-infrared spectral signatures of these contaminants we may put new constraints on the composition of the plumes and, ultimately, their source, which is currently believed to be Enceladus's global sub-surface ocean [Iess et al., 2014]. Here we present preliminary results from our analysis of observations from the Visual and Infrared Mapping Spectrometer (VIMS) [Brown et al., 2005] onboard Cassini and mapping of plume deposits across the surface of Enceladus. We have investigated the global variation of the water ice Fresnel peak at 3.1 μm, which may be used as an indicator of ice crystallinity [Hansen & McCord, 2004; Jaumann et al., 2008; Newman et al., 2008]. We have also investigated the slope of the 1.11-2.25 μm spectral region, which serves as an indicator of water ice grain size for small grains (< 100 μm) as well as the presence of contaminants [e.g. Filacchione et al., 2010]. Finally, we have identified and mapped an absorption feature centered at 3.25 μm that may be related to organic contaminants, represented by the band depth of the fundamental C-H stretch [e.g. Cruikshank et al., 2014; Scipioni et al., 2014].

African Equatorial and Subtropical Ozone Plumes: Recurrences Timescales of the Brown Cloud Trans-African Plumes and Other Plumes

NASA Technical Reports Server (NTRS)

Chatfield, Robert B.; Thompson, Anne M.; Guan, Hong; Witte, Jacquelyn C.

2004-01-01

We have found repeated illustrations in the maps of Total Tropospheric Ozone (TTO) of apparent transport of ozone from the Indian Ocean to the Equatorial Atlantic Ocean. Most interesting are examples that coincide with the INDOEX observations of late northern winter, 1999. Three soundings associated with the SHADOZ (Southern Hemisphere Additional Ozonesondes) network help confirm and quantify degree of influence of pollution, lightning, and stratospheric sources, suggesting that perhaps 40% of increased Atlantic ozone could be Asian pollution during periods of maximum identified in the TTO maps. We outline recurrent periods of apparent ozone transport from Indian to Atlantic Ocean regions both during and outside the late-winter period. These are placed in the context of some general observations about factors controlling recurrence timescales for the expression of both equatorial and subtropical plumes. Low-level subtropical plumes are often controlled by frontal systems approaching the Namib coast; these direct mid-level air into either easterly equatorial plumes or westerly mid- troposphere plumes. Equatorial plumes of ozone cross Africa on an easterly path due to the occasional coincidence of two phenomena: (1) lofting of ozone to mid and upper levels, often in the Western Indian Ocean, and (2) the eastward extension of an Equatorial African easterly jet.

Biodegradation at Dynamic Plume Fringes: Mixing Versus Reaction Control

NASA Astrophysics Data System (ADS)

Cirpka, O. A.; Eckert, D.; Griebler, C.; Haberer, C.; Kürzinger, P.; Bauer, R.; Mellage, A.

2014-12-01

Biodegradation of continuously emitted plumes is known to be most pronounced at the plume fringe, where mixing of contaminated water and ambient groundwater, containing dissolved electron acceptors, stimulates microbial activity. Under steady-state conditions, physical mixing of contaminant and electron acceptor by transverse dispersion was shown to be the major bottleneck for biodegradation, with plume lengths scaling inversely with the bulk transverse dispersivity in quasi two-dimensional settings. Under these conditions, the presence of suitable microbes is essential but the biokinetic parameters do not play an important role. When the location of the plume shifts (caused, e.g., by a fluctuating groundwater table), however, the bacteria are no more situated at the plume fringe and biomass growth, decay, activation and deactivation determine the time lag until the fringe-controlled steady state is approached again. During this time lag, degradation is incomplete. The objective of the presented study was to analyze to which extent flow and transport dynamics diminish effectiveness of fringe-controlled biodegradation and which microbial processes and related biokinetic parameters determine the system response in overall degradation to hydraulic fluctuations. We performed experiments in quasi-two-dimensional flow through microcosms on aerobic toluene degradation by Pseudomonas putida F1. Plume dynamics were simulated by vertical alteration of the toluene plume position and experimental results were analyzed by reactive-transport modeling. We found that, even after disappearance of the toluene plume for two weeks, the majority of microorganisms stayed attached to the sediment and regained their full biodegradation potential within two days after reappearance of the toluene plume. Our results underline that besides microbial growth and maintenance (often subsumed as "biomass decay") microbial dormancy (that is, change into a metabolically inactive state) and endogeneous respiration are important to understand the dynamic behavior of electron-acceptor and -donor fluxes under transient environmental conditions and therefore deserve increased consideration in future reactive-transport modeling.

Multidisciplinary studies of the dust storm that affected Sydney in September 2009

NASA Astrophysics Data System (ADS)

De Deckker, P.

2012-04-01

A major dust storm transgressed over southeastern Australia in September 2009 and continued as far as northern Queensland [to the north], New Zealand and New Caledonia [to the east] . We analysed samples of the dust for organic compounds, its microbiological composition, pollen, trace and rare earth elements as well as Sr and Nd isotopes. Grain size analysis was also performed on some of the samples. We also obtained information on the meteorological conditions that led to the large dust plume and its pathway. Our geochemical fingerprinting allowed us to determine the origin of the dust, and this was confirmed by meteorological observations and satellite imagery. As the pathway of the dust plume went over the city of Canberra, located to the southwest of Sydney, we were able to collect samples of dust that fell with rain, and the surprise was that the geochemical composition of the dust varied with time [and dust fall], identifying that as the dust plume transgressed over the landscape, it picked up additional material that was compositionally different from its point of origin. We also compared our data with those obtained from another major dust event that affected Canberra in October 2002, and a number of important differences are noted, particularly with respect of the microbiological composition of the dust, and its chemical composition. Collaborators on this project are: Chris Munday and Gwen Allison [microbiology]: Research School of Biology, ANU; Jochen Brocks and Janet Hope [organic chemistry] and Marc Norman [inorganic geochemistry]: Research School of Earth Sciences, ANU; Tadhg O'Loingsigh and Nigel Tapper [meteorology, satellite imagery] and Sander van der Kaars [palynology]: Geography and Environmental Science, Monash University; and J.-B. Stuut [grain size analysis], NIOZ.

Mantle Sources Beneath the SW Indian Ridge - Remelting the African Superplume

NASA Astrophysics Data System (ADS)

Dick, H. J. B.; Zhou, H.

2012-04-01

The SW Indian Ridge runs some 7700 km from the Bouvet to the Rodgriguez Triple Junction, crossing over or near two postulated mantle plumes. The latter are associated with large oceanic rises where the ridge axis shoals dramatically in the vicinity of the mantle hotspot. The Marion Rise, extends 3100 km from the Andrew Bain FZ to near the Rodriguez TJ, with an along axis rise of 5600-m to it crest north of Marion Island. The rise has thin crust inferred on the basis of abundant exposures of mantle peridotites along its length. We suggest that this is the result of its sub-axial mantle source, which is a depleted residue originally emplaced by the African Superplume into the asthenosphere beneath southern Africa during the Karoo volcanic event ~185 Ma. Based on shallow mantle anisotropy, plate reconstructions, and hotspot traces, it now forms the mantle substrate for the SW Indian Ridge due to the breakup of Gondwanaland. The Marion Rise is associated with Marion Island, the present location of the Marion Hotspot, some 256 km south of the modern ridge. This plume is a vestigial remnant of the African Superplume now imbedded in and centered on asthenospheric mantle derived from the Karoo event. Based on the numerous large offset fracture zones, which would dam sub-axial asthenospheric flow along the ridge, the low postulated flux of the Marion plume, its off-axis position, and the thin crust along the ridge it is clear that the present day plume does not support the Marion Rise. Instead, this must be supported isostatically by the underlying mantle residue of the Karoo event. The Bouvet Rise is much shorter than the Marion Rise, extending ~664 km from the Conrad FZ on the American-Antarctic Ridge to the Shaka FZ on the SW Indian Ridge. It has ~3000-m of axial relief, peaking at Speiss Smt at Speiss Ridge: the last spreading segment of the SW Indian Ridge adjacent to the Bouvet TJ. Unlike the Marion plume, Bouvet is ridge-centered, and much of its rise is likely supported by sub-axial flow of hot mantle from the present-day plume. It is also clear from the isotopic composition of the Bouvet Plume that while it may also be a manifestation of the underlying seismic anomaly situated above D" that gave rise to the Marion Plume, this source must be compositionally heterogeneous at a very large scale. Secondary mantle heterogeneities are evident beyond those associated with the Marion and Bouvet Plumes. These likely explain the frequently extreme local isotopic variability of MORB along the SW Indian Ridge, and are likely due to entrainment of cratonic lithosphere from beneath Africa into the asthenosphere (e.g.: Meyzen et al., Nature, 2003). This is supported by major element anomalies in peridotites from adjacent to the 750-km offset Andrew Bain FZ, and by anomalously thick crust situated at Atlantis Bank, the site of an abrupt MORB isotopic anomaly, that suggest anomalously fertile mantle sources inconsistent with the regional basalt and peridotite major element compositional gradients attributed to the Superplume.

Vertical structure of the phytoplankton community associated with a coastal plume in the Gulf of Mexico

USGS Publications Warehouse

Wawrik, B.; Paul, J.H.; Campbell, L.; Griffin, D.; Houchin, L.; Fuentes-Ortega, A.; Muller-Karger, F.

2003-01-01

Low salinity plumes of coastal origin are occasionally found far offshore, where they display a distinct color signature detectable by satellites. The impact of such plumes on carbon fixation and phytoplankton community structure in vertical profiles and on basin wide scales is poorly understood. On a research cruise in June 1999, ocean-color satellite-images (Sea-viewing Wide Field-of-view Sensor, SeaWiFS) were used in locating a Mississippi River plume in the eastern Gulf of Mexico. Profiles sampled within and outside of the plume were analyzed using flow cytometry, HPLC pigment analysis and primary production using 14C incorporation. Additionally, RubisCO large subunit (rbcL) gene expression was measured by hybridization of extracted RNA using 3 full-length RNA gene probes specific for individual phytoplankton clades. We also used a combination of RT-PCR/PCR and TA cloning in order to generate cDNA and DNA rbcL clone libraries from samples taken in the plume. Primary productivity was greatest in the low salinity surface layer of the plume. The plume was also associated with high Synechococcus counts and a strong peak in Form IA rbcL expression. Form IB rbcL (green algal) mRNA was abundant at the subsurface chlorophyll maximum (SCM), whereas Form ID rbcL (chromophytic) expression showed little vertical structure. Phylogenetic analysis of cDNA libraries demonstrated the presence of Form IA rbcL Synechococcus phylotypes in the plume. Below the plume, 2 spatially separated and genetically distinct rbcL clades of Prochlorococcus were observed. This indicated the presence of the high- and low-light adapted clades of Prochlorococcus. A large and very diverse clade of Prymnesiophytes was distributed throughout the water column, whereas a clade of closely related prasinophytes may have dominated at the SCM. These data indicate that the Mississippi river plume may dramatically alter the surface picoplankton composition of the Gulf of Mexico, with Synechococcus displacing Prochlorococcus in the surface waters.

Leg 197 synthesis: Southward motion and geochemical variability of the Hawaiian hotspot

USGS Publications Warehouse

Duncan, Robert A.; Tarduno, John A.; Scholl, David W.; Duncan, Robert A.; Tarduno, John A.; Davies, Thomas A.; Scholl, David W.

2006-01-01

The bend in the Hawaiian-Emperor volcanic chain is an often-cited example of a change in plate motion with respect to a stationary hotspot. Growing evidence, however, suggests that the bend might instead record variable drift of the Hawaiian hotspot within a convecting mantle. Paleomagnetic and radiometric age data from samples recovered during Ocean Drilling Program (ODP) Leg 197 define an age-progressive paleolatitude history, indicating that the Emperor Seamounts volcanic trend was formed principally by rapid (4–5 cm/yr) southward motion of the Hawaiian hotspot during Late Cretaceous to early Tertiary time (81–47 Ma). Paleointensity data derived from Leg 197 suggest an inverse relationship between field strength and reversal frequency, consistent with an active lower mantle that controls the efficiency of the geodynamo. Petrochemical data and observations of volcanic products (lava flows and volcaniclastic sediments) from Detroit, Nintoku, and Koko Seamounts provide records of the evolution of these volcanic systems for comparison with recent activity in the Hawaiian Islands. We find that the Emperor Seamounts formed from similar mantle sources for melting (plume components and lithosphere) and in much the same stages of volcanic activity and time span as the Hawaiian volcanoes. Changes in major and trace element and Sr isotopic compositions of shield lavas along the lineament can be related to variations in thickness of the lithosphere overlying the hotspot that control the depth and extent of partial melting. Other geochemical tracers, such as He, Pb, and Hf isotopic compositions, indicate persistent contributions to melting from the plume throughout the volcanic chain.

SEM/EDS Characterization of Ambient PM during Agricultural Burns

NASA Astrophysics Data System (ADS)

Wagner, J.; Wall, S.

2010-12-01

Ambient particulate matter (PM) samples were collected with UNC passive samplers during agricultural burns in Imperial Valley, California. Four Bermuda grass field burn events were sampled at 3-8 locations surrounding each burn. Sampling began at the start of each burn (30-60 min) and continued for 24-120 hours. During 3 of the 4 burn events, winds were calm and plumes were observed to travel straight up to the inversion layer. In one event, winds created a ground-level plume that enveloped two UNC samplers mounted on telephone poles very close to the field (0.2-0.3 miles away). Computer-controlled scanning electron microscopy / energy-dispersive x-ray spectroscopy (CCSEM/EDS) was used to measure particle sizes and elemental composition, from which mass concentrations and size distributions were calculated. The median PM2.5 and PM10 levels measured in this study were 3.4 and 20 ug/m3, respectively. To determine quantitative accuracy, UNC sampler PM2.5 results (PM< 2.5 um) were compared to PM2.5 results from four co-located, continuous-reading beta-attenuation monitors (EBAMs). The median agreement (EBAM - UNC) was 3.8 ug/m3. Manual SEM/EDS detected various distinctive species in these samples, including sea salt, spores, plant fragments, and large soot agglomerates. During the ‘plume event’, 24-hour PM2.5 exposures downwind were up to 17 times higher than that measured upwind. Numerous submicron combustion particles with carbon and oxygen only were directly observed by manual SEM/EDS in the two plume-impacted samples, along with larger ash particles enriched in potassium, sulfur, chlorine, calcium, sodium, and phosphorus. CCSEM/EDS data from this event was grouped into 5 particle classes to generate size-fraction-specific pie charts. Burn-related particle types contributed 95% of the PM2.5 in the location directly impacted by the ground-level plume, compared to only 12% in the upwind location. A sample of Imperial County Bermuda grass analyzed in bulk and partially-burned states was found to contain similar inorganic elements as the air samples impacted by the burn plume, as well as mold spores found at trace levels in various air samples.

Geochemical signals of progressive continental rupture in the Main Ethiopian Rift

NASA Astrophysics Data System (ADS)

Furman, T.; Bryce, J.; Yirgu, G.; Ayalew, D.; Cooper, L.

2003-04-01

Mafic volcanics of the Main Ethiopian Rift record the development of magmatic rift segments during continental extension. The Ethiopian Rift is one arm of a triple junction that formed above a Paleogene mantle plume, concurrent with eruption of flood basalts ca. 30 Ma across northern Ethiopian and Yemen. The geochemistry of Ethiopian Rift lavas thus provides insight into processes associated with the shift from mechanical (lithospheric) to magmatic (asthenospheric) segmentation in the transitional phase of continental rifting. Quaternary basalts from five volcanic centers representing three magmatic segments display along-axis geochemical variations that likely reflect the degree of rifting and magma supply, which increase abruptly with proximity to the highly-extended Afar region. To first order, the geochemical data indicate a decreasing degree of shallow-level fractionation and greater involvement of depleted or plume-like mantle source materials in basalts sampled closer to the Afar. These spatially controlled geochemical signatures observed in contemporaneous basalts are similar to temporal variations documented in southern Ethiopia, where Quaternary lavas indicate a greater degree of crustal extension than those erupted at the onset of plume activity. Primitive Ethiopian Rift basalts have geochemical signatures (e.g., Ce/Pb, La/Nb, Ba/Nb, Ba/Rb, U/Th) that overlap ocean island basalt compositions, suggesting involvement of sub-lithospheric source materials. The estimated depth of melting (65-75 km) is shallower than values obtained for young primitive mafic lavas from the Western Rift and southern Kenya as well as Oligocene Ethiopian flood basalts from the onset of plume-driven activity. Basalts from the Turkana region (N. Kenya) and Erta 'Ale (Danakil depression) reflect melting at shallower levels, corresponding to the greater degree of crustal extension in these provinces. Preliminary Sr and Nd isotopic data trend towards primitive earth values, consistent with values observed previously in central Ethiopia that are associated with moderately high 3He/4He values (<19 RA; Marty et al. 1996) and interpreted as reflecting involvement of a mantle plume. Taken together, these data support a model in which upwelling plume material sampled in central Ethiopia incorporates depleted mantle during ascent beneath the more highly extended portions of the African Rift.

Origin, transport and deposition of leaf-wax biomarkers in the Amazon Basin and the adjacent Atlantic

NASA Astrophysics Data System (ADS)

Häggi, Christoph; Sawakuchi, André O.; Chiessi, Cristiano M.; Mulitza, Stefan; Mollenhauer, Gesine; Sawakuchi, Henrique O.; Baker, Paul A.; Zabel, Matthias; Schefuß, Enno

2016-11-01

Paleoenvironmental studies based on terrigenous biomarker proxies from sediment cores collected close to the mouth of large river systems rely on a proper understanding of the processes controlling origin, transport and deposition of biomarkers. Here, we contribute to the understanding of these processes by analyzing long-chain n-alkanes from the Amazon River system. We use the δD composition of long-chain n-alkanes from river bed sediments from the Amazon River and its major tributaries, as well as marine core-top samples collected off northeastern South America as tracers for different source areas. The δ13C composition of the same compounds is used to differentiate between long-chain n-alkanes from modern forest vegetation and petrogenic organic matter. Our δ13C results show depleted δ13C values (-33 to -36‰) in most samples, indicating a modern forest source for most of the samples. Enriched values (-31 to -33‰) are only found in a few samples poor in organic carbon indicating minor contributions from a fossil petrogenic source. Long-chain n-alkane δD analyses show more depleted values for the western tributaries, the Madeira and Solimões Rivers (-152 to -168‰), while n-alkanes from the lowland tributaries, the Negro, Xingu and Tocantins Rivers (-142 to -154‰), yield more enriched values. The n-alkane δD values thus reflect the mean annual isotopic composition of precipitation, which is most deuterium-depleted in the western Amazon Basin and more enriched in the eastern sector of the basin. Samples from the Amazon estuary show a mixed long-chain n-alkane δD signal from both eastern lowland and western tributaries. Marine core-top samples underlying the Amazon freshwater plume yield δD values similar to those from the Amazon estuary, while core-top samples from outside the plume showed more enriched values. Although the variability in the river bed data precludes quantitative assessment of relative contributions, our results indicate that long-chain n-alkanes from the Amazon estuary and plume represent an integrated signal of different regions of the onshore basin. Our results also imply that n-alkanes are not extensively remineralized during transport and that the signal at the Amazon estuary and plume includes refractory compounds derived from the western sector of the Basin. These findings will aid in the interpretation of plant wax-based records of marine sediment cores collected from the adjacent ocean.

The source location of mantle plumes from 3D spherical models of mantle convection

NASA Astrophysics Data System (ADS)

Li, Mingming; Zhong, Shijie

2017-11-01

Mantle plumes are thought to originate from thermal boundary layers such as Earth's core-mantle boundary (CMB), and may cause intraplate volcanism such as large igneous provinces (LIPs) on the Earth's surface. Previous studies showed that the original eruption sites of deep-sourced LIPs for the last 200 Myrs occur mostly above the margins of the seismically-observed large low shear velocity provinces (LLSVPs) in the lowermost mantle. However, the mechanism that leads to the distribution of the LIPs is not clear. The location of the LIPs is largely determined by the source location of mantle plumes, but the question is under what conditions mantle plumes form outside, at the edges, or above the middle of LLSVPs. Here, we perform 3D geodynamic calculations and theoretical analyses to study the plume source location in the lowermost mantle. We find that a factor of five decrease of thermal expansivity and a factor of two increase of thermal diffusivity from the surface to the CMB, which are consistent with mineral physics studies, significantly reduce the number of mantle plumes forming far outside of thermochemical piles (i.e., LLSVPs). An increase of mantle viscosity in the lowermost mantle also reduces number of plumes far outside of piles. In addition, we find that strong plumes preferentially form at/near the edges of piles and are generally hotter than that forming on top of piles, which may explain the observations that most LIPs occur above LLSVP margins. However, some plumes originated at pile edges can later appear above the middle of piles due to lateral movement of the plumes and piles and morphologic changes of the piles. ∼65-70% strong plumes are found within 10 degrees from pile edges in our models. Although plate motion exerts significant controls over the large-scale mantle convection in the lower mantle, mantle plume formation at the CMB remains largely controlled by thermal boundary layer instability which makes it difficult to predict geographic locations of most mantle plumes. However, all our models show consistently strong plumes originating from the lowermost mantle beneath Iceland, supporting a deep mantle plume origin of the Iceland volcanism.

When smoke comes to town - effects of biomass burning smoke on air quality down under

NASA Astrophysics Data System (ADS)

Keywood, Melita; Cope, Martin; (C. P) Meyer, Mick; Iinuma, Yoshi; Emmerson, Kathryn

2014-05-01

Annually, biomass burning results in the emission of quantities of trace gases and aerosol to the atmosphere. Biomass burning emissions have a significant effect on atmospheric chemistry due to the presence of reactive species. Biomass burning aerosols influence the radiative balance of the earth-atmosphere system directly through the scattering and absorption of radiation, and indirectly through their influence on cloud microphysical processes, and therefore constitute an important forcing in climate models. They also reduce visibility, influence atmospheric photochemistry and can be inhaled into the deepest parts of the lungs, so that they can have a significant effect on human health. Australia experiences bushfires on an annual basis. In most years fires are restricted to the tropical savannah forests of Northern Australia. However in the summer of 2006/2007 (December 2006 - February 2007), South Eastern Australia was affected by the longest recorded fires in its history. During this time the State of Victoria was ravaged by 690 separate bushfires, including the major Great Divide Fire, which devastated 1,048,238 hectares over 69 days. On several occasions, thick smoke haze was transported to the Melbourne central business district and PM10 concentrations at several air quality monitoring stations peaked at over 200 µg m-3 (four times the National Environment Protection Measure PM10 24 hour standard). During this period, a comprehensive suite of air quality measurements was carried out at a location 25 km south of the Melbourne CBD, including detailed aerosol microphysical and chemical composition measurements. Here we examine the chemical and physical properties of the smoke plume as it impacted Melbourne's air shed and discuss its impact on air quality over the city. We estimate the aerosol emission rates of the source fires, the age of the plumes and investigate the transformation of the smoke as it progressed from its source to the Melbourne airshed. We show that the smoke plumes that reached Melbourne during the summer of 2006/2007 resulted in elevated concentrations of particles and gases relative to non-fire impacted periods. The age of the plume was greater when smoke reached Melbourne (note that in our calculation of the plume age we do not distinguish between smoke and anthropogenic plumes). In addition, the older smoke plumes (30 hours) displayed higher concentrations of a number of gaseous and aerosol species relative to the younger smoke plumes (3 hours), particularly secondary reaction products, while the younger smoke plumes had higher concentrations of biomass burning marker compounds. This suggests that the enhanced photochemical activity in the smoke plumes significantly changes the aerosol composition of the smoke, potentially affecting the optical and thus radiative properties of the aerosol. This has implications for the modelling of aged smoke in chemical transport and climate models.

Lu-Hf isotope constraints on plume-lithosphere interaction during emplacement of the Bushveld Large Igneous Province at 2.06 Ga: Implications for the structure and evolution of the Kaapvaal Craton's lithospheric mantle

NASA Astrophysics Data System (ADS)

Zirakparvar, N. A.; Mathez, E. A.; Rajesh, H.; Vervoort, J. D.; Choe, S.

2016-12-01

The Bushveld Large Igneous Province (B-LIP) comprises a diverse array of >30 magma bodies that intruded the Kaapvaal Craton at 2.06 Ga. In this talk we use zircon and bulk-rock Lu-Hf isotope data to show that the B-LIP formed in response to the arrival of a plume(s) from the deep mantle. New zircon Hf isotope compositions for four B-LIP bodies yield intrusion-specific average ɛHf (2.06 Ga) values that range from -20.7 ± 2.8 to -2.7 ± 2.8, largely consistent with literature zircon data for other B-LIP intrusions. Bulk-rock solution ɛHf (2.06 Ga) values for a variety of B-LIP intrusions range from -2.1 ± 0.2 to -10.6 ± 0.2. Because the most radiogenic Hf isotope compositions across the entire B-LIP are nearly primordial with an ɛHf (2.06 Ga) close to 0, it is likely that the heat source of the B-LIP was a plume(s) from deep mantle. The Hf isotope data further suggests that individual intrusions in the B-LIP can be grouped into four categories based on their ultimate sources: 1) melts generated in subduction and plume modified continental lithospheric mantle; 2) melts generated by melting of a mafic-ultramafic reservoir composed of older ( 2.7 Ga) plume-related material trapped in the Kaapvaal lithosphere; 3) melts generated in the mid- to upper crust; and 4) melts generated from the 2.06 Ga mantle plume itself. The presence of 2.7 Ga mafic-ultramafic material in the Kaapvaal lithosphere may have acted to strengthen the lithosphere so that it was able to resist being dispered by the arrival of the B-LIP plume at 2.06 Ga. Because the B-LIP extends into a 2.7 Ga aged suture zone between the Kaapvaal and Zimbabwe cratons, it is also possible to understand the role of the lithospheric mantle in producing the Lu-Hf signatures observed in the various B-LIP intrusions as a function of two different types of the continental lithosphere: The very old lithosphere comprising the Kaapvaal Craton and the somewhat younger lithosphere comprising the suture zone. A basic observation is that the Hf isotope signature of the plume source is only directly expressed in B-LIP bodies that intruded the suture zone, providing further evidence that the craton was already underlain by thick lithospheric mantle at the time of B-LIP magmatism.

Cloud Condensation Nuclei Measurements During the First Year of the ORACLES Study

NASA Astrophysics Data System (ADS)

Kacarab, M.; Howell, S. G.; Wood, R.; Redemann, J.; Nenes, A.

2016-12-01

Aerosols have significant impacts on air quality and climate. Their ability to scatter and absorb radiation and to act as cloud condensation nuclei (CCN) plays a very important role in the global climate. Biomass burning organic aerosol (BBOA) can drastically elevate the concentration of CCN in clouds, but the response in droplet number may be strongly suppressed (or even reversed) owing to low supersaturations that may develop from the strong competition of water vapor (Bougiatioti et al. 2016). Understanding and constraining the magnitude of droplet response to biomass burning plumes is an important component of the aerosol-cloud interaction problem. The southeastern Atlantic (SEA) cloud deck provides a unique opportunity to study these cloud-BBOA interactions for marine stratocumulus, as it is overlain by a large, optically thick biomass burning aerosol plume from Southern Africa during the burning season. The interaction between these biomass burning aerosols and the SEA cloud deck is being investigated in the NASA ObseRvations of Aerosols above Clouds and their intEractionS (ORACLES) study. The CCN activity of aerosol around the SEA cloud deck and associated biomass burning plume was evaluated during the first year of the ORACLES study with direct measurements of CCN concentration, aerosol size distribution and composition onboard the NASA P-3 aircraft during August and September of 2016. Here we present analysis of the observed CCN activity of the BBOA aerosol in and around the SEA cloud deck and its relationship to aerosol size, chemical composition, and plume mixing and aging. We also evaluate the predicted and observed droplet number sensitivity to the aerosol fluctuations and quantify, using the data, the drivers of droplet number variability (vertical velocity or aerosol properties) as a function of biomass burning plume characteristics.

Aircraft-Based measurement of the physico-chemical evolution of atmospheric aerosols in the air pollution plume over a megacity and a remote area

NASA Astrophysics Data System (ADS)

Park, J. S.; Lee, T.; Park, T.; Lee, J. B.; Lim, Y. J.; Ahn, J.; Kim, J.; Park, S.; Collett, J. L., Jr.

2017-12-01

Aerosols influence climate change directly (scattering and absorption) and indirectly (cloud condensation nuclei), also adverse health effects. The Korean peninsula is a great place to study different sources of the aerosols: urban, rural and marine. In addition, Seoul is one of the large metropolitan areas in the world and has a variety of sources because half of the Korean population lives in Seoul, which comprises only 12% of the country's area. To understand the physico-chemical evolution of atmospheric aerosols in the air pollution plume over a megacity and a remote area, an Aerodyne High Resolution Time of Flight Aerosol Mass Spectrometer (HR-ToF-AMS) was deployed on an airborne platform (NASA DC-8 and Beechcraft King Air) in June, 2015 and May-June, 2016 during MAPS-Seoul and KORUS-AQ campaigns, respectively, in Korea. The HR-ToF-AMS is capable of measuring non-refractory size resolved chemical composition of submicron particle (NR-PM1). NR-PM1 includes mass concentration of organics, nitrate, sulfate, and ammonium with 10 seconds time resolution. Organics was dominated species in aerosol during all of flights. Organics and nitrate were dominant around energy industrial complex near by Taean, South Korea. The presentation will provide an overview of the composition of NR-PM1 measured in air pollution plumes, and deliver detail information about width, depth and spatial distribution of the pollutant in the air pollution plumes. The results of this study will provide high temporal and spatial resolved details on the air pollution plumes, which are valuable input parameters of aerosol properties for the current air quality models.

Composition of plume-influenced mid-ocean ridge lavas and glasses from the Mid-Atlantic Ridge, East Pacific Rise, Galápagos Spreading Center, and Gulf of Aden

NASA Astrophysics Data System (ADS)

Kelley, Katherine A.; Kingsley, Richard; Schilling, Jean-Guy

2013-01-01

The global mid-ocean ridge system is peppered with localities where mantle plumes impinge on oceanic spreading centers. Here, we present new, high resolution and high precision data for 40 trace elements in 573 samples of variably plume-influenced mid-ocean ridge basalts from the Mid-Atlantic ridge, the Easter Microplate and Salas y Gomez seamounts, the Galápagos spreading center, and the Gulf of Aden, in addition to previously unpublished major element and isotopic data for these regions. Included in the data set are the unconventional trace elements Mo, Cd, Sn, Sb, W, and Tl, which are not commonly reported by most geochemical studies. We show variations in the ratios Mo/Ce, Cd/Dy, Sn/Sm, Sb/Ce, W/U, and Rb/Tl, which are expected not to fractionate significantly during melting or crystallization, as a function of proximity to plume-related features on these ridges. The Cd/Dy and Sn/Sm ratios show little variation with plume proximity, although higher Cd/Dy may signal increases in the role of garnet in the mantle source beneath some plumes. Globally, the Rb/Tl ratio closely approximates the La/SmN ratio, and thus provides a sensitive tracer of enriched mantle domains. The W/U ratio is not elevated at plume centers, but we find significant enrichments in W/U, and to a lesser extent the Mo/Ce and Sb/Ce ratios, at mid-ocean ridges proximal to plumes. Such enrichments may provide evidence of far-field entrainment of lower mantle material that has interacted with the core by deeply-rooted, upwelling mantle plumes.

Single-cell genomics reveals features of a Colwellia species that was dominant during the Deepwater Horizon oil spill.

PubMed

Mason, Olivia U; Han, James; Woyke, Tanja; Jansson, Janet K

2014-01-01

During the Deepwater Horizon (DWH) oil spill in the Gulf of Mexico a deep-sea hydrocarbon plume developed resulting in a rapid succession of bacteria. Colwellia eventually supplanted Oceanospirillales, which dominated the plume early in the spill. These successional changes may have resulted, in part, from the changing composition and abundance of hydrocarbons over time. Colwellia abundance peaked when gaseous and simple aromatic hydrocarbons increased, yet the metabolic pathway used by Colwellia in hydrocarbon disposition is unknown. Here we used single-cell genomics to gain insights into the genome properties of a Colwellia enriched during the DWH deep-sea plume. A single amplified genome (SAG) of a Colwellia cell isolated from a DWH plume, closely related (avg. 98% 16S rRNA gene similarity) to other plume Colwellia, was sequenced and annotated. The SAG was similar to the sequenced isolate Colwellia psychrerythraea 34H (84% avg. nucleotide identity). Both had genes for denitrification, chemotaxis, and motility, adaptations to cold environments and a suite of nutrient acquisition genes. The Colwellia SAG may be capable of gaseous and aromatic hydrocarbon degradation, which contrasts with a DWH plume Oceanospirillales SAG which encoded non-gaseous n-alkane and cycloalkane degradation pathways. The disparate hydrocarbon degradation pathways are consistent with hydrocarbons that were abundant at different times in the deep-sea plume; first, non-gaseous n-alkanes and cycloalkanes that could be degraded by Oceanospirillales, followed by gaseous, and simple aromatic hydrocarbons that may have been degraded by Colwellia. These insights into the genomic properties of a Colwellia species, which were supported by existing metagenomic sequence data from the plume and DWH contaminated sediments, help further our understanding of the successional changes in the dominant microbial players in the plume over the course of the DWH spill.

Atmospheric pressure matrix-assisted laser desorption ionization as a plume diagnostic tool in laser evaporation methods

NASA Astrophysics Data System (ADS)

Callahan, John H.; Galicia, Marsha C.; Vertes, Akos

2002-09-01

Laser evaporation techniques, including matrix-assisted pulsed laser evaporation (MAPLE), are attracting increasing attention due to their ability to deposit thin layers of undegraded synthetic and biopolymers. Laser evaporation methods can be implemented in reflection geometry with the laser and the substrate positioned on the same side of the target. In some applications (e.g. direct write, DW), however, transmission geometry is used, i.e. the thin target is placed between the laser and the substrate. In this case, the laser pulse perforates the target and transfers some target material to the substrate. In order to optimize evaporation processes it is important to know the composition of the target plume and the material deposited from the plume. We used a recently introduced analytical method, atmospheric pressure matrix-assisted laser desorption ionization (AP-MALDI) to characterize the ionic components of the plume both in reflection and in transmission geometry. This technique can also be used to directly probe materials deposited on surfaces (such as glass slides) by laser evaporation methods. The test compound (small peptides, e.g. Angiotensin I, ATI or Substance P) was mixed with a MALDI matrix (α-cyano-4-hydroxycinnamic acid (CHCA), sinapinic acid (SA) or 2,5-dihydroxybenzoic acid (DHB)) and applied to the stainless steel (reflection geometry) or transparent conducting (transmission geometry) target holder. In addition to the classical dried droplet method, we also used electrospray target deposition to gain better control of crystallite size, thickness and homogeneity. The target was mounted in front of the inlet orifice of an ion trap mass spectrometer (IT-MS) that sampled the ionic components of the plume generated by a nitrogen laser. We studied the effect of several parameters, such as, the orifice to target distance, illumination geometry, extracting voltage distribution and sample preparation on the generated ions. Various analyte-matrix and matrix-matrix cluster ions were observed with relatively low abundance of the matrix ions.

Magmatic plumbing system from lower mantle of Hainan plume

NASA Astrophysics Data System (ADS)

Xia, Shaohong; Sun, Jinlong; Xu, Huilong; Huang, Haibo; Cao, Jinghe

2017-04-01

Intraplate volcanism during Late Cenozoic in the Leiqiong area of southernmost South China, with basaltic lava flows covering a total of more than 7000 km2, has been attributed to an underlying Hainan plume. However, detailed features of Hainan plume, such as morphology of magmatic conduits, depth of magmatic pool in the upper mantle and pattern of mantle upwelling, are still enigmatic. Here we present seismic tomographic images of the upper 1100 km of the mantle beneath the southern South China. Our results show a mushroom-like continuous low-velocity anomaly characterized by a columnar tail with diameter of about 200-300 km that tilts downward to lower mantle beneath north of Hainan hotspot and a head that spreads laterally near the mantle transition zone, indicating a magmatic pool in the upper mantle. Further upward, this head is decomposed into small patches, but when encountering the base of the lithosphere, a pancake-like anomaly is shaped again to feed the Hainan volcanism. Our results challenge the classical model of a fixed thermal plume that rises vertically to the surface, and propose the new layering-style pattern of magmatic upwelling of Hainan plume. This work indicates the spatial complexities and differences of global mantle plumes probably due to heterogeneous compositions and changefully thermochemical structures of deep mantle.

Distribution of Trace Gases and Aerosols in the Troposphere Over Siberia During Wildfires of Summer 2012

NASA Astrophysics Data System (ADS)

Antokhin, P. N.; Arshinova, V. G.; Arshinov, M. Y.; Belan, B. D.; Belan, S. B.; Davydov, D. K.; Ivlev, G. A.; Fofonov, A. V.; Kozlov, A. V.; Paris, J.-D.; Nedelec, P.; Rasskazchikova, T. M.; Savkin, D. E.; Simonenkov, D. V.; Sklyadneva, T. K.; Tolmachev, G. N.

2018-02-01

The results of sensing of the gas and aerosol composition of the atmosphere with the Optik Tu-134 aircraft laboratory in the period from 31 July to 1 August 2012 are presented. The measurements were conducted along the flight route Novosibirsk-Tomsk-Mirny-Yakutsk-Bratsk-Novosibirsk. A significant part of the Siberian territory during this period was covered by numerous forest fires. The synoptic situation during the measurements was characterized by the presence of low-gradient field. This fact determined the low rate of transport and diffusion of pollutants and their accumulation in the region under study. The maximal concentrations of CO2, CH4, and CO over fire zones achieved 432 ppm, 2367 ppb, and 4036 ppb, respectively. The aerosol particle number density in emission plumes achieved 4400 cm-3. Outside emission plumes, the concentration ranged within 400-1000 cm-3 depending on the region. The mass concentration of aerosol in plumes increased approximately 7 times (6.9). The enrichment of the concentration of some elements and ions in the plume with respect to the background varied from 1.3 to 9.1 times. The generation of ozone from biomass burning products was observed at plume boundaries. Two versions of this process are possible: ozone generation under and above the plume.

Hydrocarbon emissions from in-use commercial aircraft during airport operations.

PubMed

Herndon, Scott C; Rogers, Todd; Dunlea, Edward J; Jayne, John T; Miake-Lye, Richard; Knighton, Berk

2006-07-15

The emissions of selected hydrocarbons from in-use commercial aircraft at a major airport in the United States were characterized using proton-transfer reaction mass spectrometry (PTR-MS) and tunable infrared differential absorption spectroscopy (TILDAS) to probe the composition of diluted exhaust plumes downwind. The emission indices for formaldehyde, acetaldehyde, benzene, and toluene, as well as other hydrocarbon species, were determined through analysis of 45 intercepted plumes identified as being associated with specific aircraft. As would have been predicted for high bypass turbine engines, the hydrocarbon emission index was greater in idle and taxiway acceleration plumes relative to approach and takeoff plumes. The opposite was seen in total NOy emission index, which increased from idle to takeoff. Within the idle plumes sampled in this study, the median emission index for formaldehyde was 1.1 g of HCHO per kg of fuel. For the subset of hydrocarbons measured in this work, the idle emissions levels relative to formaldehyde agree well with those of previous studies. The projected total unburned hydrocarbons (UHC) deduced from the range of in-use idle plumes analyzed in this work is greater than a plausible range of engine types using the defined idle condition (7% of rated engine thrust) in the International Civil Aviation Organization (ICAO) databank reference.

Lithology and temperature: How key mantle variables control rift volcanism

NASA Astrophysics Data System (ADS)

Shorttle, O.; Hoggard, M.; Matthews, S.; Maclennan, J.

2015-12-01

Continental rifting is often associated with extensive magmatic activity, emplacing millions of cubic kilometres of basalt and triggering environmental change. The lasting geological record of this volcanic catastrophism are the large igneous provinces found at the margins of many continents and abrupt extinctions in the fossil record, most strikingly that found at the Permo-Triassic boundary. Rather than being considered purely a passive plate tectonic phenomenon, these episodes are frequently explained by the involvement of mantle plumes, upwellings of mantle rock made buoyant by their high temperatures. However, there has been debate over the relative role of the mantle's temperature and composition in generating the large volumes of magma involved in rift and intra-plate volcanism, and even when the mantle is inferred to be hot, this has been variously attributed to mantle plumes or continental insulation effects. To help resolve these uncertainties we have combined geochemical, geophysical and modelling results in a two stage approach: Firstly, we have investigated how mantle composition and temperature contribute to melting beneath Iceland, the present day manifestation of the mantle plume implicated in the 54Ma break up of the North Atlantic. By considering both the igneous crustal production on Iceland and the chemistry of its basalts we have been able to place stringent constraints on the viable temperature and lithology of the Icelandic mantle. Although a >100°C excess temperature is required to generate Iceland's thick igneous crust, geochemistry also indicates that pyroxenite comprises 10% of its source. Therefore, the dynamics of rifting on Iceland are modulated both by thermal and compositional mantle anomalies. Secondly, we have performed a global assessment of the mantle's post break-up thermal history to determine the amplitude and longevity of continental insulation in driving excess volcanism. Using seismically constrained igneous crustal thicknesses as a proxy for mantle temperature, we find that break-up is rarely accompanied by significant thermal excesses. Importantly, even when high breakup temperatures are inferred within several million years these have decayed to background levels, limiting the long-term significance of continental insulation on rifting.

Superfund record of decision (EPA Region 7): Cornhusker Army Ammunition Plant, Operable Unit 1, Hall County, Grand Island, NE, September 29, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-04-01

The decision document presents the selected interim remedial action for the groundwater operable unit at the Cornhusker Army Ammunition Plant (CAAP). Operable Unit One encompasses the explosives groundwater plume(s), both on-post and off-post. Explosives of concern in the contaminant plume include RDX, TNT, HMX, and their decomposition products. The objective of the interim action is to contain the plume and prevent further migration of contaminants, and does not encompass full restoration of the plume of contaminated groundwater. The recommended alternatives provide an approach to containing and removing contaminant mass from the groundwater plume. This approach will control further migration ofmore » the plume and reduce the levels of the contamination in groundwater.« less

Preliminary disposal limits, plume interaction factors, and final disposal limits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flach, G.

In the 2008 E-Area Performance Assessment (PA), each final disposal limit was constructed as the product of a preliminary disposal limit and a plume interaction factor. The following mathematical development demonstrates that performance objectives are generally expected to be satisfied with high confidence under practical PA scenarios using this method. However, radionuclides that experience significant decay between a disposal unit and the 100-meter boundary, such as H-3 and Sr-90, can challenge performance objectives, depending on the disposed-of waste composition, facility geometry, and the significance of the plume interaction factor. Pros and cons of analyzing single disposal units or multiple disposalmore » units as a group in the preliminary disposal limits analysis are also identified.« less

The impact of glacier geometry on meltwater plume structure and submarine melt in Greenland fjords

NASA Astrophysics Data System (ADS)

Carroll, D.; Sutherland, D. A.; Hudson, B.; Moon, T.; Catania, G. A.; Shroyer, E. L.; Nash, J. D.; Bartholomaus, T. C.; Felikson, D.; Stearns, L. A.; Noël, B. P. Y.; Broeke, M. R.

2016-09-01

Meltwater from the Greenland Ice Sheet often drains subglacially into fjords, driving upwelling plumes at glacier termini. Ocean models and observations of submarine termini suggest that plumes enhance melt and undercutting, leading to calving and potential glacier destabilization. Here we systematically evaluate how simulated plume structure and submarine melt during summer months depends on realistic ranges of subglacial discharge, glacier depth, and ocean stratification from 12 Greenland fjords. Our results show that grounding line depth is a strong control on plume-induced submarine melt: deep glaciers produce warm, salty subsurface plumes that undercut termini, and shallow glaciers produce cold, fresh surface-trapped plumes that can overcut termini. Due to sustained upwelling velocities, plumes in cold, shallow fjords can induce equivalent depth-averaged melt rates compared to warm, deep fjords. These results detail a direct ocean-ice feedback that can affect the Greenland Ice Sheet.

Flow field description of the Space Shuttle Vernier reaction control system exhaust plumes

NASA Technical Reports Server (NTRS)

Cerimele, Mary P.; Alred, John W.

1987-01-01

The flow field for the Vernier Reaction Control System (VRCS) jets of the Space Shuttle Orbiter has been calculated from the nozzle throat to the far-field region. The calculations involved the use of recently improved rocket engine nozzle/plume codes. The flow field is discussed, and a brief overview of the calculation techniques is presented. In addition, a proposed on-orbit plume measurement experiment, designed to improve future estimations of the Vernier flow field, is addressed.

Pulsed jet combustion generator for non-premixed charge engines

DOEpatents

Oppenheim, A. K.; Stewart, H. E.

1990-01-01

A device for introducing fuel into the head space of cylinder of non-premixed charge (diesel) engines is disclosed, which distributes fuel in atomized form in a plume, whose fluid dynamic properties are such that the compression heated air in the cylinder head space is entrained into the interior of the plume where it is mixed with and ignites the fuel in the plume interior, to thereby control combustion, particularly by use of a multiplicity of individually controllable devices per cylinder.

Mineralogy and geochemistry of picro-dolerite dykes from the central Deccan Traps flood basaltic province, India, and their geodynamic significance

NASA Astrophysics Data System (ADS)

Dongre, Ashish; Viljoen, K. S.; Rathod, A.

2018-04-01

Constituent mineral compositions and whole rock major element geochemistry of picro-dolerite dykes from the central part of the Deccan flood basalt province are presented and discussed. The dykes are characterized by an MgO content of about 13 wt%, coupled with 13-16 modal percents of olivine. A high whole rock molar Mg# value of 71 and the presence of magnesian olivine phenocrysts ( Fo78) are consistent with a primitive (i.e. unevolved) geochemistry. The nature and composition of clinopyroxene (augite and pigeonite), plagioclase feldspar (labradorite) and Fe-Ti oxides (mostly ilmenite and magnetite) are also discussed, with implications drawn with respect to the geodynamics. High MgO magmas and rocks such as picrites are generally considered to be indicative of plume magmatism, formed by high degrees of partial melting in, e.g. the high-temperature region of a plume head. Recent age data is consistent with a model in which the Deccan LIP picritic magmatism is associated with the main phase of Deccan Trap activity at 66 Ma, as a result of a syn- to post rifting phase associated with the impact of the Rèunion mantle plume. It is speculated that the differentiation of primary olivine basaltic magma of picritic composition, may have been the mechanism for the generation of alkalic basalts which occurs in the Deccan Trap basaltic sequence.

Updated Conceptual Model for the 300 Area Uranium Groundwater Plume

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zachara, John M.; Freshley, Mark D.; Last, George V.

2012-11-01

The 300 Area uranium groundwater plume in the 300-FF-5 Operable Unit is residual from past discharge of nuclear fuel fabrication wastes to a number of liquid (and solid) disposal sites. The source zones in the disposal sites were remediated by excavation and backfilled to grade, but sorbed uranium remains in deeper, unexcavated vadose zone sediments. In spite of source term removal, the groundwater plume has shown remarkable persistence, with concentrations exceeding the drinking water standard over an area of approximately 1 km2. The plume resides within a coupled vadose zone, groundwater, river zone system of immense complexity and scale. Interactionsmore » between geologic structure, the hydrologic system driven by the Columbia River, groundwater-river exchange points, and the geochemistry of uranium contribute to persistence of the plume. The U.S. Department of Energy (DOE) recently completed a Remedial Investigation/Feasibility Study (RI/FS) to document characterization of the 300 Area uranium plume and plan for beginning to implement proposed remedial actions. As part of the RI/FS document, a conceptual model was developed that integrates knowledge of the hydrogeologic and geochemical properties of the 300 Area and controlling processes to yield an understanding of how the system behaves and the variables that control it. Recent results from the Hanford Integrated Field Research Challenge site and the Subsurface Biogeochemistry Scientific Focus Area Project funded by the DOE Office of Science were used to update the conceptual model and provide an assessment of key factors controlling plume persistence.« less

Chemical Characterization of Individual Particles and Residuals of Cloud Droplets and Ice Crystals Collected On Board Research Aircraft in the ISDAC 2008 Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hiranuma, Naruki; Brooks, Sarah D.; Moffet, Ryan C.

2013-06-24

Although it has been shown that size of atmospheric particles has a direct correlation with their ability to act as cloud droplet and ice nuclei, the influence of composition of freshly emitted and aged particles in nucleation processes is poorly understood. In this work we combine data from field measurements of ice nucleation with chemical imaging of the sampled particles to link aerosol composition with ice nucleation ability. Field measurements and sampling were conducted during the Indirect and Semidirect Aerosols Campaign (ISDAC) over Barrow, Alaska, in the springtime of 2008. In-situ ice nucleation measurements were conducted using a Continuous Flowmore » Diffusion Chamber (CFDC). Measured number concentrations of ice nuclei (IN) varied from frequent values of 0.01 per liter to more than 10 per liter. Residuals of airborne droplets and ice crystals were collected through a counterflow virtual impactor (CVI). The compositions of individual atmospheric particles and the residuals were studied using Computer Controlled Scanning Electron Microscopy with Energy Dispersive X-ray analysis (CCSEM/EDX) and Scanning Transmission X-ray Microscopy coupled with Near Edge X-ray Absorption Fine Structure spectroscopy (STXM/NEXAFS). Chemical analysis of cloud particle residuals collected during an episode of high ice nucleation suggests that both size and composition may influence aerosol's ability to act as IN. The STXM/NEXAFS chemical composition maps of individual residuals have characteristic structures of either inorganic or black carbon cores coated by organic materials. In a separate flight, particle samples from a biomass burning plume were collected. Although it has previously been suggested that episodes of biomass burning contribute to increased numbers of highly effective ice nuclei, in this episode we observed that only a small fraction were effective ice nuclei. Most of the particles from the biomass plume episode were smaller in size and were composed of homogeneous organic material without identifiable cores.« less

The effects of magmatic processes and crustal recycling on the molybdenum stable isotopic composition of Mid-Ocean Ridge Basalts

NASA Astrophysics Data System (ADS)

Bezard, Rachel; Fischer-Gödde, Mario; Hamelin, Cédric; Brennecka, Gregory A.; Kleine, Thorsten

2016-11-01

Molybdenum (Mo) stable isotopes hold great potential to investigate the processes involved in planetary formation and differentiation. However their use is currently hampered by the lack of understanding of the dominant controls driving mass-dependent fractionations at high temperature. Here we investigate the role of magmatic processes and mantle source heterogeneities on the Mo isotope composition of Mid-Ocean Ridges Basalts (MORBs) using samples from two contrasting ridge segments: (1) the extremely fast spreading Pacific-Antarctic (66-41°S) section devoid of plume influence and; (2) the slow spreading Mohns-Knipovich segment (77-71°N) intercepted by the Jan Mayen Plume (71°N). We show that significant variations in Mo stable isotope composition exist in MORBs with δ98/95Mo ranging from - 0.24 ‰ to + 0.15 ‰ (relative to NIST SRM3134). The absence of correlation between δ98/95Mo and indices of magma differentiation or partial melting suggests a negligible impact of these processes on the isotopic variations observed. On the other hand, the δ98/95Mo variations seem to be associated with changes in radiogenic isotope signatures and rare earth element ratios (e.g., (La/Sm)N), suggesting mantle source heterogeneities as a dominant factor for the δ98/95Mo variations amongst MORBs. The heaviest Mo isotope compositions correspond to the most enriched signatures, suggesting that recycled crustal components are isotopically heavy compared to the uncontaminated depleted mantle. The uncontaminated depleted mantle shows slightly sub-chondritic δ98/95Mo, which cannot be produced by core formation and, therefore, more likely result from extensive anterior partial melting of the mantle. Consequently, the primitive δ98/95Mo composition of the depleted mantle appears overprinted by the effects of both partial melting and crustal recycling.

Dynamics and Deposits of Coignimbrite Plumes

NASA Astrophysics Data System (ADS)

Engwell, Samantha; de'Michieli Vitturi, Mattia; Esposti Ongaro, Tomaso; Neri, Augusto

2014-05-01

Fine ash in the atmosphere poses a significant hazard, with potentially disastrous consequences for aviation and, on deposition, health and infrastructure. Fine-grained particles form a large proportion of ejecta in Plinian volcanic clouds. However, another common, but poorly studied phenomena exists whereby large amounts of fine ash are injected into the atmosphere. Coignimbrite plumes form as material is elutriated from the top of pyroclastic density currents. The ash in these plumes is considerably finer grained than that in Plinian plumes and can be distributed over thousands of kilometres in the atmosphere. Despite their significance, very little is known regarding coignimbrite plume formation and dispersion, predominantly due to the poor preservation of resultant deposits. As a result, consequences of coignimbrite plume formation are usually overlooked when conducting hazard and risk analysis. In this study, deposit characteristics and numerical models of plumes are combined to investigate the conditions required for coignimbrite plume formation. Coignimbrite deposits from the Campanian Ignimbrite eruption (Magnitude 7.7, 39 ka) are well sorted and very fine, with a mode of between 30 and 50 microns, and a significant component of respirable ash (less than 10 microns). Analogous distributions are found for coignimbrite deposits from Tungurahua 2006 and Volcan de Colima (2004-2006), amongst others, regardless of magnitude, type or chemistry of eruption. These results indicate that elutriation processes are the dominant control on coignimbrite grainsize distribution. To further investigate elutriation and coignimbrite plume dynamics, the numerical plume model of Bursik (2001) is applied. Model sensitivity analysis demonstrates that neutral buoyancy conditions (required for the formation of the plume) are controlled by a balance between temperature and gas mass flux in the upper most parts of the pyroclastic density current. In addition, results emphasize the importance of entrainment into the established plume, a process that is still poorly defined. The numerical results, and the consistent fine grained nature of ash in the deposits, highlight the importance of physical dynamics in the parent pyroclastic density currents for coignimbrite plume formation and stress the need for tailored methods to investigate hazard and risk from such events. Bursik, M. Effect of wind on the rise height of volcanic plumes. Geophysical Research Letters, 28(18), 3621-3624, 2001.

Linking Europa's plume activity to tides, tectonics, and liquid water

NASA Astrophysics Data System (ADS)

Rhoden, Alyssa Rose; Hurford, Terry A.; Roth, Lorenz; Retherford, Kurt

2015-06-01

Much of the geologic activity preserved on Europa's icy surface has been attributed to tidal deformation, mainly due to Europa's eccentric orbit. Although the surface is geologically young (30-80 Myr), there is little information as to whether tidally-driven surface processes are ongoing. However, a recent detection of water vapor near Europa's south pole suggests that it may be geologically active. Initial observations indicated that Europa's plume eruptions are time-variable and may be linked to its tidal cycle. Saturn's moon, Enceladus, which shares many similar traits with Europa, displays tidally-modulated plume eruptions, which bolstered this interpretation. However, additional observations of Europa at the same time in its orbit failed to yield a plume detection, casting doubt on the tidal control hypothesis. The purpose of this study is to analyze the timing of plume eruptions within the context of Europa's tidal cycle to determine whether such a link exists and examine the inferred similarities and differences between plume activity on Europa and Enceladus. To do this, we determine the locations and orientations of hypothetical tidally-driven fractures that best match the temporal variability of the plumes observed at Europa. Specifically, we identify model faults that are in tension at the time in Europa's orbit when a plume was detected and in compression at times when the plume was not detected. We find that tidal stress driven solely by eccentricity is incompatible with the observations unless additional mechanisms are controlling the eruption timing or restricting the longevity of the plumes. The addition of obliquity tides, and corresponding precession of the spin pole, can generate a number of model faults that are consistent with the pattern of plume detections. The locations and orientations of these hypothetical source fractures are robust across a broad range of precession rates and spin pole directions. Analysis of the stress variations across the fractures suggests that the plumes would be best observed earlier in the orbit (true anomaly ∼120°). Our results indicate that Europa's plumes, if confirmed, differ in many respects from the Enceladean plumes and that either active fractures or volatile sources are rare.

A DOM Odyssey: The Tale of Molecular Transformations in an Aquifer near Bemidji, MN

NASA Astrophysics Data System (ADS)

Podgorski, D. C.; Zito, P.; Smith, D. F.; Cao, X.; Schmidt-Rohr, K.; Wagner, S.; Stubbins, A.; Aiken, G.; Cozzarelli, I.; Bekins, B. A.; Spencer, R. G.

2017-12-01

Analytical methods including fluorescence spectroscopy, NMR spectroscopy, and ultrahigh resolution mass spectrometry have significantly advanced the understanding of compositional controls on dissolved organic matter (DOM) processing and fate. Yet, we still heavily rely on extrapolation of chemical changes identified at the edges of the compositional continuum (i.e., endmembers) to assess DOM reactivity and stability. While extrapolation of chemical transformations is useful for determining relative changes in DOM composition, a comprehensive understanding of the underlying core structures and composition is required to develop advanced biogeochemical models. Studying DOM from natural systems is complicated by many variables associated with an open system including input from multiple sources, simultaneous photo-alteration and microbial processing, and obtaining samples that cover high spatial and temporal resolution. A 38-year biodegradation study at the National Crude Oil Spill Research site near Bemidji, MN provides a unique opportunity to monitor DOM in a relatively closed system. An extensively characterized 1 m thick oil body is confined to a 25 x 75 m2 area at the water table in the aquifer. Oxidized metabolites partition from the oil into the underlying aquifer increase the DOC concentration to > 100 ppm from < 2 ppm up-gradient from the oil body. This newly produced DOM is comprised of aliphatic compounds with high H/C, low O/C and blue-shifted fluorescence, similar in composition to permafrost- and algal-derived DOM. The aliphatic DOM is transported laterally from the oil pool by groundwater, creating a plume that ultimately discharges into the Unnamed Lake 325 m downgradient. More than 10 years later and hundreds of meters downgradient from the oil body, the DOC concentration has decreased to 3-5 ppm and the DOM is compositionally non-distinct. Microbes have left behind degradation products and selectively preserved compounds that exhibit red-shifted fluorescence and molecular formulas with O/C and H/C similar to those associated with the `island of stability'. Samples collected spatially from the DOM plume between these two endmembers provide sufficient temporal resolution to model both DOC concentration and DOM composition as a result of biodegradation.

Radiogenic Isotope Constraints on Plume - Lithosphere Interaction Beneath the Snake River Plain

NASA Astrophysics Data System (ADS)

Hanan, B. B.; Shervais, J. W.; Vetter, S. K.

2006-12-01

The Snake River Plain (SRP), an 800 km swath of volcanic centers that stretch across southern Idaho to western Wyoming-Montana, represents about 16 Myr of volcanic activity that took place as the NA continent migrated over a relatively fixed magma source, or hotspot. Volcanic activity in the SRP began with the eruption of the main phase of the Columbia River Basalt Group (CRBG) at about 16.5 - 15 Ma through Paleozoic- Mesozoic lithosphere accreted to the Precambrian NA continental margin (1). At about 15 Ma, volcanism shifted to the east, across the cratonic margin into the SRP, and advanced with time to its current position on the Yellowstone Plateau (YP). Published major element, trace element, and He isotope systematics of the basaltic rocks are consistent with a deep, sub-lithospheric mantle source, similar to the source of ocean island basalts (OIBs). In contrast, the radiogenic isotopes of Pb, Sr, and Nd are indistinguishable from sub- continental mantle lithosphere (SCML) that underlies the SRP and YP. This conundrum has been a major problem for plume-oriented models for the SRP-YP hotspot. The Wyoming craton underlying the SRP has a stabilization age of around 2.8 Ga under the YP and eastern SRP area (2). Deep crustal xenoliths show a pattern of decreasing age (about 3.2-2.5 Ga) from east to west along the SRP (3,4). Compared to other Archean rocks, the Pb and Sr initial ratios are higher, and the Nd initial ratios are lower than expected for a depleted upper mantle source, suggesting a small amount of crustal material mixed into the SCML during late Archean subduction events (2). Concentrations of radiogenic incompatible elements in OIB-plume sources are nearly 100 times lower than found in the craton. Assimilation of small percentage fractional melts of the craton into large volume, larger degree partial melts derived from the plume mantle source would result in hybrid magmas whose isotopic compositions are controlled by the isotopic composition of the continental component. We tested this prediction with fifty basalts from along the SRP analyzed for major and trace contents and Pb, Sr, and Nd isotopes. The SRP Pb isotope results are consistent with mixing between an OIB-like plume component with 1% to 4% melt derived from about 2.8 Ga Wyoming-like enriched SCML and show that the relative amount of plume-like OIB component increases from 90-98% in the YP, to 98-99% in the central and western SRP. Basalts of the main phase CRBG (5), the central and eastern SRP, and the YP (6) show an overall decrease in 206Pb/204Pb and ^{143}Nd/^{144}Nd, variable 87Sr/86Sr, and increase in 207Pb/206Pb and ^{208}Pb/206Pb from west to east with distance from the Yellowstone caldera, with OIB-like values in Oregon and Washington toward values typical of the lower crust and lithosphere of the Wyoming Province along the SRP and YP. These results are consistent with a progressive decrease in craton thickness from east to west approaching the craton margin, a concomitant decrease in the age, and compositional heterogeneity in the lower crust and SCML beneath the SRP. (1) Camp and Ross, JGR 109, 2004; (2) Wooden and Mueller, EPSL 87, 1988; (3) Leeman et al., EPSL 75, 1985; (4) Wolf et al., GSA Abstracts with Programs 37, 2005; (5) Hooper, G3 1, 2000; (6) Doe, JGR 87, 1982.

Processing of aerosol particles within the Habshan pollution plume

NASA Astrophysics Data System (ADS)

Semeniuk, T. A.; Bruintjes, R.; Salazar, V.; Breed, D.; Jensen, T.; Buseck, P. R.

2015-03-01

The Habshan industrial site in the United Arab Emirates produces a regional-scale pollution plume associated with oil and gas processing, discharging high loadings of sulfates and chlorides into the atmosphere, which interact with the ambient aerosol population. Aerosol particles and trace gas chemistry at this site were studied on two flights in the summer of 2002. Measurements were collected along vertical plume profiles to show changes associated with atmospheric processing of particle and gas components. Close to the outlet stack, particle concentrations were over 10,000 cm-3, dropping to <2000 cm-3 in more dilute plume around 1500 m above the stack. Particles collected close to the stack and within the dilute plume were individually measured for size, morphology, composition, and mixing state using transmission electron microscopy coupled with energy-dispersive X-ray spectroscopy. Close to the stack, most coarse particles consisted of mineral dust and NaCl crystals from burning oil brines, while sulfate droplets dominated the fine mode. In more dilute plume, at least 1500 m above the stack, the particle spectrum was more diverse, with a significant increase in internally mixed particle types. Dilute plume samples consisted of coarse NaCl/silicate aggregates or NaCl-rich droplets, often with a sulfate component, while fine-fraction particles were of mixed cation sulfates, also internally mixed with nanospherical soot or silicates. Thus, both chloride and sulfate components of the pollution plume rapidly reacted with ambient mineral dust to form coated and aggregate particles, enhancing particle size, hygroscopicity, and reactivity of the coarse mode. The fine-fraction sulfate-bearing particles formed in the plume contribute to regional transport of sulfates, while coarse sulfate-bearing fractions locally reduced the SO2 loading through sedimentation. The chloride- and sulfate-bearing internally mixed particles formed in the plume markedly changed the reflectivity and scattering properties of the ambient aerosol population, as well as its hygroscopic and ice nucleation properties.

Isotopic evolution of Mauna Kea volcano: Results from the initial phase of the Hawaii Scientific Drilling Project

USGS Publications Warehouse

Lassiter, J.C.; DePaolo, D.J.; Tatsumoto, M.

1996-01-01

We have examined the Sr, Nd, and Pb isotopic compositions of Mauna Kea lavas recovered by the first drilling phase of the Hawaii Scientific Drilling Project. These lavas, which range in age from ???200 to 400 ka, provide a detailed record of chemical and isotopic changes in basalt composition during the shied/postshield transition and extend our record of Mauna Kea volcanism to a late-shield period roughly equivalent to the last ???100 ka of Mauna Loa activity. Stratigraphic variations in isotopic composition reveal a gradual shift over time toward a more depleted source composition (e.g., higher 143Nd/144Nd, lower 87Sr/86Sr, and lower 3He/4He). This gradual evolution is in sharp contrast with the abrupt appearance of alkalic lavas at ???240 ka recorded by the upper 50 m of Mauna Kea lavas from the core. Intercalated tholeiitic and alkalic lavas from the uppermost Mauna Kea section are isotopically indistinguishable. Combined with major element evidence (e.g., decreasing SiO2 and increasing FeO) that the depth of melt segregation increased during the transition from tholeiitic to alkalic volcanism, the isotopic similarity of tholeiitic and alkalic lavas argues against significant lithosphere involvement during melt generation. Instead, the depleted isotopic signatures found in late shield-stage lavas are best explained by increasing the proportion of melt generated from a depleted upper mantle component entrained and heated by the rising central plume. Direct comparison of Mauna Kea and Mauna Loa lavas erupted at equivalent stages in these volcanoes' life cycles reveals persistent chemical and isotopic differences independent of the temporal evolution of each volcano. The oldest lavas recovered from the drillcore are similar to modern Kilauea lavas, but are distinct from Mauna Loa lavas. Mauna Kea lavas have higher 143Nd/144Nd and 206Pb/204Pb and lower 87Sr/86Sr. Higher concentrations of incompatible trace elements in primary magmas, lower SiO2, and higher FeO also indicate that Mauna Kea lavas formed through smaller degrees of partial melting at greater depth than Mauna Loa lavas. These chemical and isotopic differences are consistently found between volcanoes along the western "Loa" and eastern "Kea" trends and reflect large-scale variations in source composition and melting environment. We propose a simple model of a radially zoned plume centered beneath the Loa trend. Loa trend lavas generated from the hot plume axis reflect high degrees of partial melting from a source containing a mixture of enriched plume-source material and entrained lower mantle. Kea trend lavas, in contrast, are generated from the cooler, peripheral portions of the plume, record lower degrees of partial melting, and tap a source containing a greater proportion of depleted upper mantle.

Orbital Maneuvering Vehicle (OMV) plume and plume effects study

NASA Technical Reports Server (NTRS)

Smith, Sheldon D.

1991-01-01

The objective was to characterize the Orbital Maneuvering Vehicle (OMV) propulsion and attitude control system engine exhaust plumes and predict the resultant plume impingement pressure, heat loads, forces, and moments. Detailed description is provided of the OMV gaseous nitrogen (GN2) thruster exhaust plume flow field characteristics calculated with the RAMP2 snd SFPGEN computer codes. Brief descriptions are included of the two models, GN2 thruster characteristics and RAMP2 input data files. The RAMP2 flow field could be recalculated by other organizations using the information presented. The GN2 flow field can be readily used by other organizations who are interested in GN2 plume induced environments which require local flow field properties which can be supplied using the SFPGEN GN2 model.

The Isotopic Record From Monogenetic Seamounts: Insights Into Recycling Time Scales In The Upper Mantle

NASA Astrophysics Data System (ADS)

Madrigal Quesada, P.; Gazel, E.

2017-12-01

Monogenetic seamounts related to non-plume intraplate magmatism provide a window into the composition of upper mantle heterogeneities, nevertheless, the origin of these heterogeneities are still not well constrained. Radiogenic isotopes (Sr-Nd-Pb) from present-day ocean island basalts (OIB) produced by this type of magmatism can help establish the source compositions of these chemically and isotopically enriched reservoirs. Here we present evidence that suggests that a highly enriched mantle reservoir can originate from OIB-type subducted material that gets incorporated and stirred throughout the upper mantle. We explore this hypothesis using data from non-plume related OIB volcanism; focusing on isolated monogenetic seamounts with no apparent age progression and interpreted to be related to either plate flexure, shear driven convection and/or edge convection. The isotopic record compiled, added to new results obtained from accreted petit-spot seamounts from Santa Elena Peninsula in Costa Rica, suggest that a highly radiogenic mantle reservoir originated from recycled seamount materials can be formed in a shorter time scale than ancient subducted oceanic crust (>1 Ga), thought to be the forming agent of the HIMU mantle "flavor" found in some of these small-scale seamounts. The implications of these results entail that the recycling of already enriched materials in short time scales and in restricted depths within the Upper Mantle may play an important role in the source of OIBs (plume and non-plume related), as well as, the most enriched suites of EMORBs.

Use of ERTS-1 pictures in coastal oceanography in British Columbia

NASA Technical Reports Server (NTRS)

Gower, J. F. R.

1973-01-01

The ERTS-1 color composite picture of the Vancouver-Victoria region illustrates the value of ERTS data for coastal oceanography. The water of the Fraser River plume which is so clearly visible in the center of the scene has been of interest to oceanographers on the west coast of Canada for a long time as an easily visible tracer of surface water circulation in the strait of Georgia. Maps of the plume at different states of the tide and with different river flow and weather were compiled from oblique aerial photographs in 1950 and used in the siting of sewage and other outfalls in the Vancouver area. More recently high level aerial photomosaics have been used to map the plume area, but the plume can spread over distances of 30 to 40 miles and many photographs, with the uneven illumination inherent in wide angle coverage, are needed for the mosaic. The ERTS satellite gives the first complete view of the plume area. Electronic enhancement of the images shows that the satellite's narrow angle coverage allows very weak surface turbidity features to be made visible to give information on surface currents over a wide area.

Liquid Water on Enceladus from Observations of Ammonia and Ar-40 in the Plume

NASA Technical Reports Server (NTRS)

Waite, J. H., Jr.; Lewis, W. S.; Magee, B. A.; Lunine, J. I.; McKinnon, W. B.; Glein, C. R.; Mousis, O.; Young, D. T.; Brockwell, T.; Westlake, J.;

Analysis of Plume Impingement Effects from Orion Crew Service Module Dual Reaction Control System Engine Firings

NASA Technical Reports Server (NTRS)

Prisbell, Andrew; Marichalar, J.; Lumpkin, F.; LeBeau, G.

2010-01-01

Plume impingement effects on the Orion Crew Service Module (CSM) were analyzed for various dual Reaction Control System (RCS) engine firings and various configurations of the solar arrays. The study was performed using a decoupled computational fluid dynamics (CFD) and Direct Simulation Monte Carlo (DSMC) approach. This approach included a single jet plume solution for the R1E RCS engine computed with the General Aerodynamic Simulation Program (GASP) CFD code. The CFD solution was used to create an inflow surface for the DSMC solution based on the Bird continuum breakdown parameter. The DSMC solution was then used to model the dual RCS plume impingement effects on the entire CSM geometry with deployed solar arrays. However, because the continuum breakdown parameter of 0.5 could not be achieved due to geometrical constraints and because high resolution in the plume shock interaction region is desired, a focused DSMC simulation modeling only the plumes and the shock interaction region was performed. This high resolution intermediate solution was then used as the inflow to the larger DSMC solution to obtain plume impingement heating, forces, and moments on the CSM and the solar arrays for a total of 21 cases that were analyzed. The results of these simulations were used to populate the Orion CSM Aerothermal Database.

Capturing volcanic plumes in 3D with UAV-based photogrammetry at Yasur Volcano - Vanuatu

NASA Astrophysics Data System (ADS)

Gomez, C.; Kennedy, B.

2018-01-01

As a precise volume of volcanic ash-plume is essential to understand the dynamic of gas emission, exchanges and the eruptive dynamics, we have measured in 3D using photogrammetry a small-size volcanic plume at the summit of Yasur Volcano, Vanuatu. The objective was to collect the altitude and planform shape of the plume as well as the vertical variations of the shape and size. To reach this objective, the authors have used the Structure from Motion photogrammetric method applied to a series of photographs captured in a very short period of time around and above the plume. A total of 146 photographs at 3000 × 4000 pixel were collected as well as the geolocation, the pitch, tilt and orientation of the cameras. The results revealed a "mushroom"-like shape of the plume with a narrow ascending column topped by a turbulent mixing zone. The volume of the plume was calculated to be 13,430 m3 ± 512 m3 (with the error being the cube of the linear error from the Ground Control Points) for a maximum height above the terrain of 63 m. The included error was also kept high because of the irregular distribution of the Ground Control Points that could not be collected in dangerous areas due to the ongoing eruption. Based on this research, it is therefore worth investigating the usage of multiple cameras to capture plumes in 3D over time and the method is also a good complement to the recent development of photogrammetry from space, which can tackle larger-scale eruption plumes.

Rapid passage of a small-scale mantle heterogeneity through the melting regions of Kilauea and Mauna Loa Volcanoes

NASA Astrophysics Data System (ADS)

Marske, Jared P.; Pietruszka, Aaron J.; Weis, Dominique; Garcia, Michael O.; Rhodes, J. Michael

2007-07-01

Recent Kilauea and Mauna Loa lavas provide a snapshot of the size, shape, and distribution of compositional heterogeneities within the Hawaiian mantle plume. Here we present a study of the Pb, Sr, and Nd isotope ratios of two suites of young prehistoric lavas from these volcanoes: (1) Kilauea summit lavas erupted from AD 900 to 1400, and (2) 14C-dated Mauna Loa flows erupted from ˜ 2580-140 yr before present (relative to AD 1950). These lavas display systematic isotopic fluctuations, and the Kilauea lavas span the Pb isotopic divide that was previously thought to exist between these two volcanoes. For a brief period from AD 250 to 1400, the 206Pb/ 204Pb and 87Sr/ 86Sr isotope ratios and ɛNd values of Kilauea and Mauna Loa lavas departed from values typical for each volcano (based on historical and other young prehistoric lavas), moved towards an intermediate composition, and subsequently returned to typical values. This is the only known period in the eruptive history of these volcanoes when such a simultaneous convergence of Pb, Sr, and Nd isotope ratios has occurred. The common isotopic composition of lavas erupted from both Kilauea and Mauna Loa during this transient magmatic event was probably caused by the rapid passage of a small-scale compositional heterogeneity through the melting regions of both volcanoes. This heterogeneity is thought to have been either a single body (˜ 35 km long based on the distance between the summits of these volcanoes) or the plume matrix itself (which would be expected to be present beneath both volcanoes). The time scale of this event (centuries) is much shorter than previously noted for variations in the isotopic composition of Hawaiian lavas due to the upwelling of heterogeneities within the plume (thousands to tens of thousands of years). Calculations based on the timing of the isotopic convergence suggest a maximum thickness for the melting region (and thus, the heterogeneity) of ˜ 5-10 km. The small size of the heterogeneity indicates that melt can be extracted from small regions within the Hawaiian plume with minimal subsequent chemical modification (beyond the effects of crystal fractionation). This would be most effective if melt transport in the mantle beneath Hawaiian shield volcanoes occurs mostly in chemically isolated channels.

The geology and geochemistry of Isla Floreana, Galápagos: A different type of late-stage ocean island volcanism: Chapter 6 in The Galápagos: A natural laboratory for the earth sciences

USGS Publications Warehouse

Harpp, Karen S.; Geist, Dennis J.; Koleszar, Alison M.; Christensen, Branden; Lyons, John; Sabga, Melissa; Rollins, Nathan; Harpp, Karen S.; Mittelstaedt, Eric; d'Ozouville, Noémi; Graham, David W

2014-01-01

Isla Floreana, the southernmost volcano in the Galápagos Archipelago, has erupted a diverse suite of alkaline basalts continually since 1.5 Ma. Because these basalts have different compositions than xenoliths and older lavas from the deep submarine sector of the volcano, Floreana is interpreted as being in a rejuvenescent or late-stage phase of volcanism. Most lavas contain xenoliths, or their disaggregated remains. The xenolithic debris and large ranges in composition, including during single eruptions, indicate that the magmas do not reside in crustal magma chambers, unlike magmas in the western Galápagos. Floreana lavas have distinctive trace element compositions that are rich in fluid-immobile elements (e.g., Ta, Nb, Th, Zr) and even richer in fluid-mobile elements (e.g., Ba, Sr, Pb). Rare earth element (REE) patterns are light REE-enriched and distinctively concave-up. Neodymium isotopic ratios are comparable to those from Fernandina, at the core of the Galápagos plume, but Floreana has the most radiogenic Sr and Pb isotopic ratios in the archipelago. These trace element patterns and isotopic ratios are attributed to a mixed source originating within the Galápagos plume, which includes depleted upper mantle, plume material rich in TITAN elements (Ti, Ta, Nb), and recycled oceanic crust that has undergone partial dehydration in an ancient subduction zone. Because Floreana lies at the periphery of the Galápagos plume, melting occurs mostly in the spinel zone, and enriched components dominate; the Floreana recycled mantle component influence is detectable in volcanoes along the entire southern periphery of the archipelago as well. Floreana is the only Galápagos volcano known to have undergone late-stage volcanism. Here, however, the secondary stage activity is more compositionally enriched than the shield-building phase, in contrast to what is observed in Hawai‘i, suggesting that the mechanism driving late-stage volcanism may vary among ocean island provinces.

Biowaste resistojet propellant system biological and functional analysis, task 3

NASA Technical Reports Server (NTRS)

1972-01-01

Exhaust flow contamination aspects of the biowaste resistojet are studied by evaluating effects of operating pressure, temperature and composition. Biowaste propellant mixtures considered are comprised of: (1) The Sabatier reactor effluent; (2) the effluent of the cabin carbon dioxide molecular sieve; and (3) water and water vapor from various sources. Results show that plume shapes of resistojet thrusters in the 25 to 100 mlb range exhibit greater apex angles for a given density contour than a scaled inviscid jet. Operation at low thrust, low pressure and high temperature accentuates this pluming due to viscous effects in the nozzle flow. Since the biowaste resistojet effluent is traveling at high velocity in the plume away from the aircraft it is found to be a superior method of damping than the ambient venting.

Contrasted hydrothermal activity along the South-East Indian Ridge (130°E-140°E): From crustal to ultramafic circulation

NASA Astrophysics Data System (ADS)

Boulart, Cédric; Briais, Anne; Chavagnac, Valérie; Révillon, Sidonie; Ceuleneer, Georges; Donval, Jean-Pierre; Guyader, Vivien; Barrere, Fabienne; Ferreira, Nicolas; Hanan, Barry; Hémond, Christophe; Macleod, Sarah; Maia, Marcia; Maillard, Agnès.; Merkuryev, Sergey; Park, Sung-Hyun; Ruellan, Etienne; Schohn, Alexandre; Watson, Sally; Yang, Yun-Seok

2017-07-01

Using a combined approach of seafloor mapping, MAPR and CTD survey, we report evidence for active hydrothermal venting along the 130°-140°E section of the poorly-known South-East Indian Ridge (SEIR) from the Australia-Antarctic Discordance (AAD) to the George V Fracture Zone (FZ). Along the latter, we report Eh and CH4 anomalies in the water column above a serpentinite massif, which unambiguously testify for ultramafic-related fluid flow. This is the first time that such circulation is observed on an intermediate-spreading ridge. The ridge axis itself is characterized by numerous off-axis volcanoes, suggesting a high magma supply. The water column survey indicates the presence of at least ten distinct hydrothermal plumes along the axis. The CH4:Mn ratios of the plumes vary from 0.37 to 0.65 denoting different underlying processes, from typical basalt-hosted to ultramafic-hosted high-temperature hydrothermal circulation. Our data suggest that the change of mantle temperature along the SEIR not only regulates the magma supply, but also the hydrothermal activity. The distribution of hydrothermal plumes from a ridge segment to another implies secondary controls such as the presence of fractures and faults along the axis or in the axial discontinuities. We conclude from these results that hydrothermal activity along the SEIR is controlled by magmatic processes at the regional scale and by the tectonics at the segment scale, which influences the type of hydrothermal circulation and leads to various chemical compositions. Such variety may impact global biogeochemical cycles, especially in the Southern Ocean where hydrothermal venting might be the only source of nutrients.

Mapping Pollution Plumes in Areas Impacted by Hurricane Katrina With Imaging Spectroscopy

NASA Astrophysics Data System (ADS)

Swayze, G. A.; Furlong, E. T.; Livo, K. E.

2007-12-01

New Orleans endured flooding on a massive scale subsequent to Hurricane Katrina in August of 2005. Contaminant plumes were noticeable in satellite images of the city in the days following flooding. Many of these plumes were caused by oil, gasoline, and diesel that leaked from inundated vehicles, gas stations, and refineries. News reports also suggested that the flood waters were contaminated with sewage from breached pipes. Effluent plumes such as these pose a potential health hazard to humans and wildlife in the aftermath of hurricanes and potentially from other catastrophic events (e.g., earthquakes, shipping accidents, chemical spills, and terrorist attacks). While the extent of effluent plumes can be gauged with synthetic aperture radar and broad- band visible-infrared images (Rykhus, 2005) (e.g., Radarsat and Landsat ETM+) the composition of the plumes could not be determined. These instruments lack the spectral resolution necessary to do chemical identification. Imaging spectroscopy may help solve this problem. Over 60 flight lines of NASA Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data were collected over New Orleans, the Mississippi Delta, and the Gulf Coast from one to two weeks after Katrina while the contaminated water was being pumped out of flooded areas. These data provide a unique opportunity to test if imaging spectrometer data can be used to identify the chemistry of these flood-related plumes. Many chemicals have unique spectral signatures in the ultraviolet to near-infrared range (0.2 - 2.5 microns) that can be used as fingerprints for their identification. We are particularly interested in detecting thin films of oil, gasoline, diesel, and raw sewage suspended on or in water. If these materials can be successfully differentiated in the lab then we will use spectral-shape matching algorithms to look for their spectral signatures in the AVIRIS data collected over New Orleans and other areas impacted by Katrina. If imaging spectroscopy can be used to identify plume composition on a regional scale than this information would help emergency personnel prioritize evacuations, help government agencies formulate cleanup strategies, and help ecologists assess the potential damage to wetlands and wildlife. This work could be the start of a new application of hyperspectral data for world-wide monitoring of spills from space-based imaging spectrometers. AVIRIS data used to test our method were corrected for solar flux, atmospheric absorptions, and scattering using the Atmospheric CORrection Now (ACORN) radiative transfer algorithm and residual artifacts were removed using ground spectra of a concrete runway at the Gulfport Airport in Mississippi. The resulting apparent reflectance data were mapped for spectral signatures of pollution plumes and results will be presented.

Distinguishing remobilized ash from erupted volcanic plumes using space-borne multi-angle imaging.

PubMed

Flower, Verity J B; Kahn, Ralph A

2017-10-28

Volcanic systems are comprised of a complex combination of ongoing eruptive activity and secondary hazards, such as remobilized ash plumes. Similarities in the visual characteristics of remobilized and erupted plumes, as imaged by satellite-based remote sensing, complicate the accurate classification of these events. The stereo imaging capabilities of the Multi-angle Imaging SpectroRadiometer (MISR) were used to determine the altitude and distribution of suspended particles. Remobilized ash shows distinct dispersion, with particles distributed within ~1.5 km of the surface. Particle transport is consistently constrained by local topography, limiting dispersion pathways downwind. The MISR Research Aerosol (RA) retrieval algorithm was used to assess plume particle microphysical properties. Remobilized ash plumes displayed a dominance of large particles with consistent absorption and angularity properties, distinct from emitted plumes. The combination of vertical distribution, topographic control, and particle microphysical properties makes it possible to distinguish remobilized ash flows from eruptive plumes, globally.

An evaluation of the uncertainties in biomass burning emissions

NASA Astrophysics Data System (ADS)

Yano, A.; Garcia Menendez, F.; Hu, Y.; Odman, M.

2012-12-01

The contribution of biomass burning emissions to the atmospheric loads of gases and aerosols can lead to major air quality problems and have significant climate impacts. Whether from wildfires, natural or human-induced, or controlled burns, biomass burning emissions are an important source of air pollutants regionally in certain parts of the world as well as globally. There are two common ways of estimating biomass burning emissions: by using either ground-based information or satellite observations. When there is sufficient local information about the burn area, the types of fuels and their consumption amounts, and the progression of the fire, ground-based estimation is preferred. For controlled burns a.k.a. prescribed burns and wildfires in places where land management is practiced to a certain extent there is typically sufficient ground-based information for emissions estimation. However, for remote regions where no ground-based information is available on the size, intensity, or the spread of the fire, estimates based on satellite observations are preferred. For example, burn location, size and timing information can be obtained from satellite retrievals of thermal anomalies and fuel loading information can be obtained from satellite products of vegetation cover. In both cases, reasonable emission estimates for a variety of pollutants can be obtained by using emission factors (mass of pollutant released per unit mass of fuel consumed) derived from field or laboratory studies. Here, emissions from a controlled burn and a wildfire are estimated using both ground-based information and satellite observations. The controlled burn was conducted on 17 November 2009 near Santa Barbara, California over 80 ha of land covered with chaparral. An aircraft tracked the smoke plume and measured CO2, light scattering, as well as meteorological parameters during the burn (Akagi et al., 2011). The wildfire is from the summer of 2008 when tens of thousands hectares of wild land burned in Northern California causing unprecedented damage. NASA Aircraft commissioned for the ARCTAS campaign at the time flew over the fires and collected data detailing composition of gases and aerosols in the fire plumes (Singh et al., 2012). We model the fires using a newly developed system consisting of a plume rise and dispersion model specifically designed for wild-land fire plumes (Daysmoke; Achtemeier et al., 2011) coupled with a regional-scale chemistry-transport model (CMAQ). Wind fields generated by a weather prediction model (WRF) are adjusted locally to match the aircraft measurements of wind speed and direction. The fires are simulated using both ground-based and satellite-based estimates of emissions. Predicted concentrations of gases and aerosols are compared to corresponding aircraft measurements. Satellite retrievals of aerosol optical depth are also used in evaluating model predictions. The new modeling system along with the wind adjustments reduces several of the uncertainties inherent to regional-scale modeling of plume transport. This allows for a more reliable analysis of the uncertainties related to emissions. Uncertainties in the magnitudes and timings of emissions, and in plume injection heights with respect to boundary layer heights are investigated. Uncertainties associated with ground-based and satellite-based emissions estimation methods are compared to each other.

Plumes do not Exist: Plate Circulation is Confined to Upper Mantle

NASA Astrophysics Data System (ADS)

Hamilton, W. B.

2002-12-01

Plumes from deep mantle are widely conjectured to define an absolute reference frame, inaugurate rifting, drive plates, and profoundly modify oceans and continents. Mantle properties and composition are assumed to be whatever enables plumes. Nevertheless, purported critical evidence for plume speculation is false, and all data are better interpreted without plumes. Plume fantasies are made ever more complex and ad hoc to evade contradictory data, and have no predictive value because plumes do not exist. All plume conjecture derives from Hawaii and the guess that the Emperor-Hawaii inflection records a 60-degree change in Pacific plate direction at 45 Ma. Paleomagnetic latitudes and smooth Pacific spreading patterns disprove any such change. Rationales for other fixed plumes collapse when tested, and hypotheses of jumping, splitting, and gyrating plumes are specious. Thermal and physical properties of Hawaiian lithosphere falsify plume predictions. Purported tomographic support elsewhere represents artifacts and misleading presentations. Asthenosphere is everywhere near solidus temperature, so melt needs a tensional setting for egress but not local heat. Gradational and inconsistent contrasts between MORB and OIB are as required by depth-varying melt generation and behavior in contrasted settings and do not indicate systematically unlike sources. MORB melts rise, with minimal reaction, through hot asthenosphere, whereas OIB melts react with cool lithosphere, and lose mass, by crystallizing refractories and retaining and assimilating fusibles. The unfractionated lower mantle of plume conjecture is contrary to cosmologic and thermodynamic data, for mantle below 660 km is more refractory than that above. Subduction, due to density inversion by top-down cooling that forms oceanic lithosphere, drives plate tectonics and upper-mantle circulation. It organizes plate motions and lithosphere stress, which controls plate boundaries and volcanic chains. Hinge rollback is the key to kinematics. Arcs advance and collide, fast-spreading Pacific shrinks, etc. A fore-arc basin atop an overriding plate shows that hinge and non-shortening plate front there track together: velocities of rollback and advance are equal. Convergence velocity commonly also equals rollback velocity but often is greater. Slabs sinking broadside push upper mantle back under incoming plates and force rapid Pacific spreading, whereas overriding plates flow forward with retreating hinges. Backarc basins open behind island arcs migrating with hinges. Slabs settle on uncrossable 660-km discontinuity. (Contrary tomographic claims reflect sampling and smearing artifacts, notably due to along-slab raypaths.) Plates advance over sunken slabs and mantle displaced rearward by them, and ridges spread where advancing plates pull away. Ridges migrate over asthenosphere, producing geophysical and bathymetric asymmetry, and tap fresh asthenosphere into which slab material is recycled upward. Sluggish deep-mantle circulation is decoupled from rapid upper-mantle circulation, so plate motions can be referenced to semistable lower mantle. Global plate motions make kinematic sense if Antarctica, almost ringed by departing ridges and varying little in Cenozoic paleomagnetic position, is stationary: hinges roll back, ridges migrate, and directions and velocities of plate rotations accord with subduction, including sliding and crowding of oceanic lithosphere toward free edges, as the dominant drive. (The invalid hotspot and no-net-rotation frames minimize motions of hinges and ridges, and their plate motions lack kinematic sense.) Northern Eurasia also is almost stationary, Africa rotates very slowly counterclockwise toward Aegean and Zagros, Pacific plate races toward surface-exit subduction systems, etc.

An Ultraviolet Spectrograph Concept for Exploring Ocean Worlds

NASA Astrophysics Data System (ADS)

Schindhelm, E. R.; Hendrix, A. R.; Fleming, B. T.

2018-05-01

UV spectroscopy can probe dust/ice composition of the surface or plumes via uniquely identifying features. We present a technology concept for a future planetary science UV multi-object imaging spectrograph.

Volatile organic compounds composition of merged and aged forest fire plumes from Alaska and western Canada

NASA Astrophysics Data System (ADS)

de Gouw, J. A.; Warneke, C.; Stohl, A.; Wollny, A. G.; Brock, C. A.; Cooper, O. R.; Holloway, J. S.; Trainer, M.; Fehsenfeld, F. C.; Atlas, E. L.; Donnelly, S. G.; Stroud, V.; Lueb, A.

2006-05-01

The NOAA WP-3 aircraft intercepted aged forest fire plumes from Alaska and western Canada during several flights of the NEAQS-ITCT 2k4 mission in 2004. Measurements of acetonitrile (CH3CN) indicated that the air masses had been influenced by biomass burning. The locations of the plume intercepts were well described using emissions estimates and calculations with the transport model FLEXPART. The best description of the data was generally obtained when FLEXPART injected the forest fire emissions to high altitudes in the model. The observed plumes were generally drier than the surrounding air masses at the same altitude, suggesting that the fire plumes had been processed by clouds and that moisture had been removed by precipitation. Different degrees of photochemical processing of the plumes were determined from the measurements of aromatic VOCs. The removal of aromatic VOCs was slow considering the transport times estimated from the FLEXPART model. This suggests that the average OH levels were low during the transport, which may be explained by the low humidity and high concentrations of carbon monoxide and other pollutants. In contrast with previous work, no strong secondary production of acetone, methanol and acetic acid is inferred from the measurements. A clear case of removal of submicron particle volume and acetic acid due to precipitation scavenging was observed.

U.S. Geological survey program on toxic waste--ground-water contamination; proceedings of the Second technical meeting, Cape Cod, Massachusetts, October 21-25, 1985

USGS Publications Warehouse

Ragone, S.E.

1988-01-01

This study characterizes the clay minerals in sediments associated with a plume of creosote-contaminated groundwater. The plume of contaminated groundwater near Pensacola, FL, is in shallow, permeable, Miocene to Holocene quartz sand and flows southward toward Pensacola Bay. Clay-size fractions were separated from 41 cores, chiefly split-spoon samples at 13 drill sites. The most striking feature of the chemical analyses of the clay fractions from uncontaminated site 2 and contaminated sites 4,5,6, and 7 is the variability of iron oxide (species in some samples as Fe2O3); total iron oxide abundance is lowest (2.5%) in uncontaminated sample 2-40, but is > 4.5% (4.5 to 8.5%) in the remaining assemblages. One feature suggesting interaction between the indigenous clays and the waste plume is the presence of nontronite-rich smectite. Nontronite commonly has been identified as the product of hydrothermal alteration and deep-sea weathering of submarine basalts; it is not a common constituent of Cenozoic Gulf Coast sediments. At the Pensacola site, relatively abundant nontronitic smectite is confined to contaminated sands or associated muds; it is least abundant or absent in sands and muds peripheral to the waste plume. The geochemistry of the waste plume, its substantial dissolved, (chiefly ferrous iron), mildly acidic (pH 5-6), and low redox composition, provides an environment similar to that previously determined for the low-temperature synthesis of nontronite. Data from clay-size fractions confirm conclusions that neoformed pyrite in some grain coatings occurs in an assemblage with excess iron over that required in the pyrite. Continuing studies to evaluate these tentative conclusions include: (1) chemical analysis of clay fractions from remaining sites to further examine the apparent relation between iron content and abundance of nontronitic smectite; (2) clay separation and analysis, and pore fluid extraction (squeezing or ultracentrifugation) and analysis from a continuous core through the mud lens to determine pore fluid composition (presence or absence of waste fluid), and character of associated clay minerals; and (3) clay separation and analysis in both permeable sands and the intervening mud lens that are clearly outside the limits of the waste plume to further document the effects of the plume. (See also W90-00022) (Lantz-PTT)

New Hafnium Isotope and Trace Element Constraints on the Role of a Plume in Genesis of the Eastern Snake River Plain Basalts, Idaho

NASA Astrophysics Data System (ADS)

Taylor, R. D.; Reid, M. R.; Blichert-Toft, J.

2009-12-01

Bimodal volcanism associated with the eastern Snake River Plain (ESRP)-Yellowstone Plateau province has persisted since approximately 16 Ma. A time-transgressive track of rhyolitic eruptions which young progressively to the east and parallel the motion of the North American plate are overlain by younger basalts with no age progression. Interpretations for the origin of these basalts range from a thermo-chemical mantle plume to incipient melting of the shallow upper mantle, and remain controversial. The enigmatic ESRP basalts are characterized by high 3He/4He, diagnostic of a plume source, but also by lithophile radiogenic isotope signatures that are more enriched than expected for plume-derived OIBs. These features could possibly be caused by isotopic decoupling associated with shallow melting of a hybridized upper mantle, or derivation from an atypical mantle plume, or both by way of mixing. New Hf isotope and trace element data further constrain potential sources for the ESRP basalts. Their Hf isotopic signatures (ɛHf = +0.1 to -5.8) are moderately enriched and consistently fall above or in the upper part of the field of OIBs, with similar Nd isotope signatures (ɛNd = -2.0 to -5.8), indicating a source with high time-integrated Lu/Hf compared with Sm/Nd. The isotopic compositions of the basalts lie between those of Archean SCML and a more depleted end-member source, suggestive of contributions from at least two sources. The grouping of isotopic characteristics is compact compared to other regional volcanism, implying that the hybridization process is highly reproducible within the ESRP. Minor localized differences in isotopic composition may signify local variations in the relative proportions of the end-members. Trace element patterns also support genesis of the ESRP basalts from an enriched source. Our data detect evidence of deeper contributions derived from the garnet-stability field, and a greater affinity of the trace element signatures to plume sources than to sources in the mantle lithosphere. The Hf isotope and trace element characteristics of the ESRP basalts thus support a model of derivation from a deep mantle plume with additional melt contributions and isotopic overprinting from SCML.

Rare gas isotopes and parent trace elements in ultrabasic-alkaline-carbonatite complexes, Kola Peninsula: identification of lower mantle plume component

NASA Astrophysics Data System (ADS)

Tolstikhin, I. N.; Kamensky, I. L.; Marty, B.; Nivin, V. A.; Vetrin, V. R.; Balaganskaya, E. G.; Ikorsky, S. V.; Gannibal, M. A.; Weiss, D.; Verhulst, A.; Demaiffe, D.

2002-03-01

During the Devonian magmatism (370 Ma ago) ∼20 ultrabasic-alkaline-carbonatite complexes (UACC) were formed in the Kola Peninsula (north-east of the Baltic Shield). In order to understand mantle and crust sources and processes having set these complexes, rare gases were studied in ∼300 rocks and mineral separates from 9 UACC, and concentrations of parent Li, K, U, and Th were measured in ∼70 samples. 4He/3He ratios in He released by fusion vary from pure radiogenic values ∼108 down to 6 × 104. The cosmogenic and extraterrestrial sources as well as the radiogenic production are unable to account for the extremely high abundances of 3He, up to 4 × 10-9 cc/g, indicating a mantle-derived fluid in the Kola rocks. In some samples helium extracted by crushing shows quite low 4He/3He = 3 × 104, well below the mean ratio in mid ocean ridge basalts (MORB), (8.9 ± 1.0) × 104, indicating the contribution of 3He-rich plume component. Magnetites are principal carriers of this component. Trapped 3He is extracted from these minerals at high temperatures 1100°C to 1600°C which may correspond to decrepitation or annealing primary fluid inclusions, whereas radiogenic 4He is manly released at a temperature range of 500°C to 1200°C, probably corresponding to activation of 4He sites degraded by U, Th decay. Similar 4He/3He ratios were observed in Oligocene flood basalts from the Ethiopian plume. According to a paleo-plate-tectonic reconstruction, 450 Ma ago the Baltica (including the Kola Peninsula) continent drifted not far from the present-day site of that plume. It appears that both magmatic provinces could relate to one and the same deep-seated mantle source. The neon isotopic compositions confirm the occurrence of a plume component since, within a conventional 20Ne/22Ne versus 21Ne/22Ne diagram, the regression line for Kola samples is indistinguishable from those typical of plumes, such as Loihi (Hawaii). 20Ne/22Ne ratios (up to 12.1) correlate well with 40Ar/36Ar ones, allowing to infer a source 40Ar/36Ar ratio of about 4000 for the mantle end-member, which is 10 times lower than that of the MORB source end-member. In (3He/22Ne)PRIM versus (4He/21Ne)RAD plot the Kola samples are within array established for plume and MORB samples; almost constant production ratio of (4He/21Ne)RAD ≅ 2 × 107 is translated via this array into (3He/22Ne)PRIM ∼ 10. The latter value approaches the solar ratio implying the non-fractionated solar-like rare gas pattern in a plume source. The Kola UACC show systematic variations in the respective contributions of in situ-produced radiogenic isotopes and mantle-derived isotopes. Since these complexes were essentially plutonic, we propose that the depth of emplacement exerted a primary control on the retention of both trapped and radiogenic species, which is consistent with geological observations. The available data allow to infer the following sequence of processes for the emplacement and evolution of Kola Devonian UACC: 1) Ascent of the plume from the lower mantle to the subcontinental lithosphere; the plume triggered mantle metasomatism not later than ∼700 to 400 Ma ago. 2) Metasomatism of the lithosphere (beneath the central part of the Kola Peninsula), including enrichment in volatile (e.g., He, Ne) and in incompatible (e.g., U, Th) elements. 3) Multistage intrusions of parental melts, their degassing, and crystallisation differentiation ∼370 Ma ago. 4) Postcrystallisation migration of fluids, including loss of radiogenic and of trapped helium. Based on model compositions of the principle terrestrial reservoirs we estimate the contributions (by mass) of the plume material, the upper mantle material, and the atmosphere (air-saturated groundwater), into the source of parent melt at ∼2%, 97.95%, and ∼0.05%, respectively.

A Mass Spectrometry Study of Isotope Separation in the Laser Plume

NASA Astrophysics Data System (ADS)

Suen, Timothy Wu

Accurate quantification of isotope ratios is critical for both preventing the development of illicit weapons programs in nuclear safeguards and identifying the source of smuggled material in nuclear forensics. While isotope analysis has traditionally been performed by mass spectrometry, the need for in situ measurements has prompted the development of optical techniques, such as laser-induced breakdown spectroscopy (LIBS) and laser ablation molecular isotopic spectrometry (LAMIS). These optical measurements rely on laser ablation for direct solid sampling, but several past studies have suggested that the distribution of isotopes in the ablation plume is not uniform. This study seeks to characterize isotope separation in the laser plume through the use of orthogonal-acceleration time-of-flight mass spectrometry. A silver foil was ablated with a Nd:YAG at 355 nm at an energy of 50 muJ with a spot size of 71 mum, for a fluence of 1.3 J/cm2 and an irradiance of 250 MW/cm2. Flat-plate repellers were used to sample the plume, and a temporal profile of the ions was obtained by varying the time delay on the high-voltage pulse. A spatial profile along the axis of the plume was generated by changing the position of the sample, which yielded snapshots of the isotopic composition with time. In addition, the reflectron time-of-flight system was used as an energy filter in conjunction with the repellers to sample slices of the laser plasma orthogonal to the plume axis. Mass spectrometry of the plume revealed a fast ion distribution and a slow ion distribution. Measurements taken across the entire plume showed the fast 109Ag ions slightly ahead in both space and time, causing the 107Ag fraction to drop to 0.34 at 3 mus, 4 mm from the sample surface. Although measurements centered on the near side of the plume did not show isotope separation, the slow ions on the far side of the plume included much more 109Ag than 107Ag. In addition to examining the isotope content of the ablation plume, this study has developed a mass spectrometry characterization technique that may be useful for investigating chemical reactions during laser ablation.

Seismic constraints on the lithosphere-asthenosphere boundary

NASA Astrophysics Data System (ADS)

Rychert, Catherine A.

2014-05-01

The basic tenet of plate tectonics is that a rigid plate, or lithosphere, moves over a weaker asthenospheric layer. However, the exact location and defining mechanism of the boundary at the base of the plate, the lithosphere-asthenosphere boundary (LAB) is debated. The oceans should represent a simple scenario since the lithosphere is predicted to thicken with seafloor age if it thermally defined, whereas a constant plate thickness might indicate a compositional definition. However, the oceans are remote and difficult to constrain, and studies with different sensitivities and resolutions have come to different conclusions. Hotspot regions lend additional insight, since they are relatively well instrumented with seismic stations, and also since the effect of a thermal plume on the LAB should depend on the defining mechanism of the plate. Here I present new results using S-to-P receiver functions to image upper mantle discontinuity structure beneath volcanically active regions including Hawaii, Iceland, Galapagos, and Afar. In particular I focus on the lithosphere-asthenosphere boundary and discontinuities related to the base of melting, which can be used to highlight plume locations. I image a lithosphere-asthenosphere boundary in the 50 - 95 km depth range beneath Hawaii, Galapagos, and Iceland. Although LAB depth variations exist within these regions, significant thinning is not observed in the locations of hypothesized plume impingement from receiver functions (see below). Since a purely thermally defined lithosphere is expected to thin significantly in the presence of a thermal plume anomaly, a compositional component in the definition of the LAB is implied. Beneath Afar, an LAB is imaged at 75 km depth on the flank of the rift, but no LAB is imaged beneath the rift itself. The transition from flank of rift is relatively abrupt, again suggesting something other than a purely thermally defined lithosphere. Melt may also exist in the asthenosphere in these regions of hotpot volcanism. Indeed, S-to-P also images strong velocity increases that are likely related to the base of a melt-rich layer beneath the oceanic LAB. This discontinuity may highlight plume locations since melt is predicted deeper at thermal anomalies. For instance, beneath Hawaii the base of melting increases from 110 km to 155 km depth 100 km west of Hawaii, i.e., the likely location of plume impingement on the lithosphere. Beneath Galapagos the discontinuity is deeper in 3 sectors, all off the island axis, suggesting multiple plume diversions and complex plume-ridge interactions. Beneath Iceland deepening is imaged to the northeast of the island. Beneath the Afar rift a shallow melt discontinuity is imaged at ~75 km, suggesting that the plume is located outside the study region. Overall, the deepest realizations of the discontinuities agree with the slowest velocities from surface waves, but are not located directly beneath surface volcanoes. This suggests that either plumes approach the surface at an angle or that restite roots beneath hotspots divert plumes at shallow depths. In either case, mantle melts are likely guided from the location of impingement on the lithosphere to current day surface volcanoes by pre-existing structures of the lithosphere.

Performance of deep-rooted phreatophytic trees at a site containing total petroleum hydrocarbons.

PubMed

Ferro, Ari M; Adham, Tareq; Berra, Brett; Tsao, David

2013-01-01

Poplar and willow tree stands were installed in 2003 at a site in Raleigh, North Carolina containing total petroleum hydrocarbon - contaminated groundwater. The objective was groundwater uptake and plume control. The water table was 5 to 6 m below ground surface (bgs) and therefore methods were used to encourage deep root development. Growth rates, rooting depth and sap flow were measured for trees in Plot A located in the center of the plume and in Plot B peripheral to the plume. The trees were initially sub-irrigated with vertically installed drip-lines and by 2005 had roots 4 to 5 m bgs. Water balance calculations suggested groundwater uptake. In 2007, the average sap flow was higher for Plot B (approximately 59 L per day per tree) than for Plot A (approximately 23 L per day per tree), probably as a result of TPH-induced stress in Plot A. Nevertheless, the estimated rate of groundwater uptake for Plot A was sufficient, relative to the calculated rate of groundwater flux beneath the stand, that a high level of plume control was achieved based on MODFLOW modeling results. Down-gradient groundwater monitoring wells installed in late 2011 should provide quantitative data for plume control.

Comparisons of volcanic eruptions from linear and central vents on Earth, Venus, and Mars (Invited)

NASA Astrophysics Data System (ADS)

Glaze, L. S.; Baloga, S. M.

2010-12-01

Vent geometry (linear versus central) plays a significant role in the ability of an explosive eruption to sustain a buoyant, convective plume. This has important implications for the injection and dispersal of particulates into planetary atmospheres and the ability to interpret the geologic record of planetary volcanism. The approach to modeling linear volcanic vents builds on the original work by Stothers [1], and takes advantage of substantial improvements that have been made in volcanic plume modeling over the last 20 years [e.g., 2,3]. A complete system of equations describing buoyant plume rise requires at least a half dozen differential equations and another half dozen equations for the parameters and constraints within the plume and ambient atmosphere. For the cylindrically axisymmetric system of differential equations given in [2], the control volume is defined as V = πr2dz. The area through which ambient atmosphere is entrained is Ae = 2πr dz, where r is the plume radius and z is vertical distance. The analogous linear vent system has a corresponding control volume, V = 2bLdz and entrainment area, Ae ≈ 2Ldz, where L is the length of the linear plume, 2b is the width of the linear plume, and it is assumed that L >> b. For typical terrestrial boundary conditions (temperature, velocity, gas mass fraction), buoyant plumes from circular vents can be maintained with substantial maximum heights over a wide range of vent sizes. However, linear vent plumes are much more sensitive to vent size, and can maintain a convective plume only over a much more narrow range of half widths. As L increases, linear plumes become more capable of establishing a convective regime over a broad range of bo, similar to the circular vents. This is primarily because as L increases, the entrainment area of the linear plumes increases, relative to the control volume. The ability of a plume to become buoyant is driven by whether or not sufficient air can be entrained (and warmed) to reduce the bulk plume density before upward momentum is exhausted. From mass conservation, linear plumes surpass circular vents in entrainment efficiency approximately when Lo ≥ 3ro. Consistent with other work [3,4], the range of conditions for maintaining a buoyant plume from a circular vent on Venus is very narrow, and the range of linear vent widths is more limited still. Unlike the terrestrial case, linear vents on Venus appear capable of driving a plume to somewhat higher maximum altitudes, with all other things remaining equal. Similar analyses were conducted for current atmospheric conditions on Mars. Results indicate a preference for the formation of pyroclastic flows on Mars from both circular and linear vents, as opposed to widely dispersed airfall deposits. Only the Earth, with its thick wet atmosphere, favors explosive eruptions that can maintain convective plumes reaching 10s of km in altitude over a broad range of eruptive conditions. References: [1] Stothers, R.B. (1989) J Atmos Sci, 46, 2662-2670. [2] Glaze. L.S., Baloga, S. M., and Wilson, L. (1997) JGR, 102, 6099-6108. [3] Glaze, L.S. (1999) JGR, 104, 18,899-18,906. [4] Thornhill, G.D. (1993) JGR, 98, 9107-9111.

Geochemistry of Intra-Transform Lavas from the Galápagos Transform Fault

NASA Astrophysics Data System (ADS)

Morrow, T. A.; Mittelstaedt, E. L.; Harpp, K. S.

2013-12-01

The Galápagos plume has profoundly affected the development and evolution of the nearby (<250 km) Galápagos Transform Fault (GTF), a ~100km right-stepping offset in the Galápagos Spreading Center (GSC). The GTF can be divided into two sections that represent different stages of transform evolution: the northern section exhibits fully developed transform fault morphology, whereas the southern section is young, and deformation is more diffuse. Both segments are faulted extensively and include numerous small (<0.5km3) monogenetic volcanic cones, though volcanic activity is more common in the south. To examine the composition of the mantle source and melting conditions responsible for the intra-transform lavas, as well as the influence of the plume on GTF evolution, we present major element, trace element, and radiogenic isotope analysis of samples collected during SON0158, EWI0004, and MV1007 cruises. Radiogenic isotope ratio variations in the Galápagos Archipelago require four distinct mantle reservoirs across the region: PLUME, DM, FLO, and WD. We find that Galápagos Transform lavas are chemically distinct from nearby GSC lavas and neighboring seamounts. They have radiogenic isotopic compositions that lie on a mixing line between DM and PLUME, with little to no contribution from any other mantle reservoirs despite their geographic proximity to WD-influenced lavas erupted along the GSC and at nearby (<50km away) seamounts. Within the transform, lavas from the northern section are more enriched in radiogenic isotopes than lavas sampled in the southern section. Transform lavas are anomalously depleted in incompatible trace elements (ITEs) relative to GSC lavas, suggesting unique melting conditions within the transform. Isotopic variability along the transform axis indicates that mantle sources and/or melting mechanisms vary between the northern and southern sections, which may relate to their distances from the plume or the two-stage development and evolution of the Galápagos Transform Fault. We present a melting model that reproduces GTF lava chemistry from a mixture of two partial melts of PLUME and DM. We assume that the DM source has an ITE composition similar to the depleted upper mantle, melting is purely fractional, and lavas do not fractionate during ascent. Solutions were achieved using a Metropolis algorithm and constrained by observed GTF lava chemistry. Model results predict that GTF lavas are produced by a mixture of a ~3%×1% partial melt of the PLUME source and a ~5%×4% partial melt of the DM source. Our model predicts that a larger proportion of PLUME melts contribute to GTF lavas than DM melts. Absence of the WD component and relatively low concentrations of ITEs may indicate that lavas in the GTF are produced from a source that has already undergone partial melting and is being re-melted beneath the TF. Re-melting may be caused by extension across the GTF, or development of the southern section of the GTF via the ~1Ma ridge jump.

Mechanisms controlling the intra-annual mesoscale variability of SST and SPM in the southern North Sea

NASA Astrophysics Data System (ADS)

Pietrzak, Julie D.; de Boer, Gerben J.; Eleveld, Marieke A.

2011-04-01

Thermal and optical remote sensing data were used to investigate the spatial and temporal distribution of sea surface temperature (SST) and of suspended particulate matter (SPM) in the southern North Sea. Monthly SST composites showed pronounced seasonal warming of the southern North Sea and delineated the English coastal and continental coastal waters. The East-Anglia Plume is the dominant feature of the English coastal waters in the winter and autumn SPM composites, and the Rhine region of freshwater influence (ROFI), including the Flemish Banks, is the dominant feature of the continental waters. These mesoscale spatial structures are also influenced by the evolution of fronts, such as the seasonal front separating well-mixed water in the southern Bight, from the seasonally stratified central North Sea waters. A harmonic analysis of the SST and SPM images showed pronounced seasonal variability, as well as spring-neap variations in the level of tidal mixing in the East Anglia Plume, the Rhine ROFI and central North Sea. The harmonic analysis indicates the important role played by the local meteorology and tides in governing the SST and near-surface SPM concentrations in the southern North Sea. In the summer, thermal stratification affects the visibility of SPM to satellite sensors in the waters to the north of the Flamborough and Frisian Fronts. Haline stratification plays an important role in the visibility of SPM in the Rhine ROFI throughout the year. When stratified, both regions typically exhibit low surface SPM values. A numerical model study, together with the harmonic analysis, highlights the importance of tides and waves in controlling the stratification in the southern North Sea and hence the visibility of SPM.

From initiation to termination: a petrostratigraphic tour of the Ethiopian Low-Ti Flood Basalt Province

NASA Astrophysics Data System (ADS)

Krans, S. R.; Rooney, T. O.; Kappelman, J.; Yirgu, G.; Ayalew, D.

2018-05-01

Continental flood basalts (CFBs), thought to preserve the magmatic record of an impinging mantle plume head, offer spatial and temporal insights into melt generation processes in large igneous provinces (LIPs). Despite the utility of CFBs in probing mantle plume composition, these basalts typically erupt fractionated compositions, suggestive of significant residence time in the continental lithosphere. The location and duration of residence within the lithosphere provide additional insights into the flux of plume-related magmas. The NW Ethiopian plateau offers a well-preserved stratigraphic sequence from flood basalt initiation to termination, and is thus an important target for study of CFBs. This study examines modal observations within a stratigraphic framework and places these observations within the context of the magmatic evolution of the Ethiopian CFB province. Data demonstrate multiple pulses of magma recharge punctuated by brief shut-down events, with initial flows fed by magmas that experienced deeper fractionation (lower crust). Broad changes in modal mineralogy and flow cyclicity are consistent with fluctuating changes in magmatic flux through a complex plumbing system, indicating pulsed magma flux and an overall shallowing of the magmatic plumbing system over time. The composition of plagioclase megacrysts suggests a constant replenishing of new primitive magma recharging the shallow plumbing system during the main phase of volcanism, reaching an apex prior to flood basalt termination. The petrostratigraphic data sets presented in this paper provide new insight into the evolution of a magma plumbing system in a CFB province.

The temperature of primary melts and mantle sources of komatiites, OIBs, MORBs and LIPs

NASA Astrophysics Data System (ADS)

Sobolev, Alexander

2015-04-01

There is general agreement that the convecting mantle, although mostly peridotitic in composition, is compositionally and thermally heterogeneous on different spatial scales. The amount, sizes, temperatures and compositions of these heterogeneities significantly affect mantle dynamics because they may diverge greatly from dominant peridotites in their density and fusibility. Differences in potential temperature and composition of mantle domains affect magma production and cannot be easily distinguished from each other. This has led to radically different interpretations of the melting anomalies that produce ocean-island basalts, large igneous provinces and komatiites: most scientists believe that they originate as hot, deep-sourced mantle plumes; but a small though influential group (e.g. Anderson 2005, Foulger, 2010) propose that they derive from high proportions of easily fusible recycled or delaminated crust, or in the case of komatiites contain large amount of H2O (e.g. Grove & Parman, 2004). The way to resolve this ambiguity is an independent estimation of temperature and composition of mantle sources of various types of magma. In this paper I report application of newly developed olivine-spinel-melt geothermometers based on partition of Al, Cr, Sc and Y for different primitive lavas from mid-ocean ridges, ocean-island basalts, large igneous provinces and komatiites. The results suggest significant variations of crystallization temperature for the same Fo of high magnesium olivines of different types of mantle-derived magmas: from the lowest (down to 1220 degree C) for MORB to the highest (up to over 1500 degree C) for komatiites and Siberian meimechites. These results match predictions from Fe-Mg olivine-melt equilibrium and confirm the relatively low temperature of the mantle source of MORB and higher temperatures in the mantle plumes that produce the OIB of Iceland, Hawaii, Gorgona, Archean komatiites and several LIPs (e.g Siberian and NAMP). The established liquidus temperatures and compositions of primary melts allow estimating potential temperatures and compositions of their mantle sources. The results strongly confirm mantle plume theory and presence of variable amounts of recycled crustal material in the mantle sources. This study has been founded by Russian Science Foundation grant 14-17-00491.

CO2 driven weathering vs plume driven weathering as inferred from the groundwater of a persistently degassing basaltic volcano: Mt. Etna

NASA Astrophysics Data System (ADS)

Liotta, Marcello; D'Alessandro, Walter

2016-04-01

At Mt. Etna the presence of a persistent volcanic plume provides large amounts of volcanogenic elements to the bulk deposition along its flanks. The volcanic plume consists of solid particles, acidic droplets and gaseous species. After H2O and CO2, S, Cl and F represent the most abundant volatile elements emitted as gaseous species from the craters. During rain events acidic gases interact rapidly with droplets lowering the pH of rain. This process favors the dissolution and dissociation of the most acidic gases. Under these conditions, the chemical weathering of volcanic rocks and ashes is promoted by the acid rain during its infiltration. Subsequently during groundwater circulation, chemical weathering of volcanic rocks is also driven by the huge amount of deep magmatic carbon dioxide (CO2) coming up through the volcanic edifice and dissolving in the water. These two different weathering steps occur under very different conditions. The former occurs in a highly acidic environment (pH < 4) and the reaction rates depend strongly on the pH, while the latter usually occurs under slightly acidic conditions since the pH has been already neutralized by the interaction with volcanics rocks. The high content of chlorine is mainly derived from interactions between the plume and rainwater, while the total alkalinity can be completely ascribed to the dissociation of carbonic acid (H2CO3) after the hydration of CO2. The relative contributions of plume-derived elements/weathering and CO2-driven weathering has been computed for each element. In addition, the comparison between the chemical compositions of the bulk deposition and of groundwater provides a new understanding about the mobility of volatile elements. Other processes such as ion exchange, iddingsite formation, and carbonate precipitation can also play roles, but only to minor extents. The proposed approach has revealed that the persistent plume strongly affects the chemical composition of groundwater at Mt. Etna and probably also at other volcanoes characterized by huge open-conduit degassing activity.

Petrogenesis of nephelinites from the Tarim Large Igneous Province, NW China: Implications for mantle source characteristics and plume-lithosphere interaction

NASA Astrophysics Data System (ADS)

Cheng, Zhiguo; Zhang, Zhaochong; Hou, Tong; Santosh, M.; Zhang, Dongyang; Ke, Shan

2015-04-01

The nephelinite exposed in the Wajilitage area in the northwestern margin of the Tarim large igneous province (TLIP), Xinjiang, NW China display porphyritic textures with clinopyroxene, nepheline and olivine as the major phenocryst phases, together with minor apatite, sodalite and alkali feldspar. The groundmass typically has cryptocrystalline texture and is composed of crystallites of clinopyroxene, nepheline, Fe-Ti oxides, sodalite, apatite, rutile, biotite, amphibole and alkali feldspar. We report rutile SIMS U-Pb age of 268 ± 30 Ma suggesting that the nephelinite may represent the last phase of the TLIP magmatism, which is also confirmed by the field relation. The nephelinite shows depleted Sr-Nd isotopic compositions with age-corrected 87Sr/86Sr and εNd(t) values of 0.70348-0.70371 and + 3.28 to + 3.88 respectively indicating asthenospheric mantle source. Based on the reconstructed primary melt composition, the depth of magma generation is estimated as 115-140 km and the temperatures of mantle melting as 1540-1575 °C. The hotter than normal asthenospheric mantle temperature suggests the involvement of mantle thermal plume. The Mg isotope values display a limited range of δ26Mg from - 0.35 to - 0.55‰, which are lower than the mantle values (- 0.25‰). The Mg isotopic compositions, combined with the Sr-Nd isotopes and major and trace element data suggest that the Wajilitage nephelinite was most likely generated by low-degree partial melting of the hybridized carbonated peridotite/eclogite source, which we correlate with metasomatism by subducted carbonates within the early-middle Paleozoic convergent regime. A plume-lithosphere model is proposed with slight thinning of the lithosphere and variable depth and degree of melting of the carbonated mantle during the plume-lithosphere interaction. This model also accounts for the variation in lithology of the TLIP.

Diagnostics of Carbon Nanotube Formation in a Laser Produced Plume: Spectroscopic in situ nanotube detection using spectral absorption and surface temperature measurements by black body emission

NASA Technical Reports Server (NTRS)

DeBoer, Gary D.

2005-01-01

Carbon nanotubes hold great promise for material advancements in the areas of composites and electronics. The advancement of research in these areas is dependent upon the availability of carbon nanotubes to a broad spectrum of academic and industrial researchers. Although there has been much progress made in reducing the costs of carbon nanotubes and increasing the quality and purity of the products, an increase in demand for still less expensive and specific nanotubes types has also grown. This summer's work has involved two experiments that have been designed to further the understanding of the dynamics and chemical mechanisms of carbon nanotube formation. It is expected that a better understanding of the process of formation of nanotubes will aid current production designs and stimulate ideas for future production designs increasing the quantity, quality, and production control of carbon nanotubes. The first experiment involved the measurement of surface temperature of the target as a function of time with respect to the ablation lasers. A peak surface temperature of 5000 K was determined from spectral analysis of black body emission from the target surface. The surface temperature as a function of various changes in operating parameters was also obtained. This data is expected to aid the modeling of ablation and plume dynamics. The second experiment involved a time and spatial measurement of the spectrally resolved absorbance of the laser produced plume. This experiment explored the possibility of developing absorbance and fluorescence to detect carbon nanotubes during production. To attain control over the production of nanotubes with specific properties and reduce costs, a real time in situ diagnostics method would be very beneficial. Results from this summer's work indicate that detection of nanotubes during production may possibly be used for production feed back control.

Subduction disfigured mantle plumes: Plumes that are not plumes?

NASA Astrophysics Data System (ADS)

Druken, K. A.; Stegman, D. R.; Kincaid, C. R.; Griffiths, R. W.

2012-12-01

"Hotspot" volcanism is generally attributed to upwelling of anomalously warm mantle plumes, the intra-plate Hawaiian island chain and its simple age progression serving as an archetypal example. However, interactions of such plumes with plate margins, and in particular with subduction zones, is likely to have been a common occurrence and leads to more complicated geological records. Here we present results from a series of complementary, three-dimensional numerical and laboratory experiments that examine the dynamic interaction between negatively buoyant subducting slabs and positively buoyant mantle plumes. Slab-driven flow is shown to significantly influence the evolution and morphology of nearby plumes, which leads to a range of deformation regimes of the plume head and conduit. The success or failure of an ascending plume head to reach the lithosphere depends on the combination of plume buoyancy and position within the subduction system, where the mantle flow owing to downdip and rollback components of slab motion entrain plume material both vertically and laterally. Plumes rising within the sub-slab region tend to be suppressed by the surrounding flow field, while wedge-side plumes experience a slight enhancement before ultimately being entrained by subduction. Hotspot motion is more complex than that expected at intraplate settings and is primarily controlled by position alone. Regimes include severely deflected conduits as well as retrograde (corkscrew) motion from rollback-driven flow, often with weak and variable age-progression. The interaction styles and surface manifestations of plumes can be predicted from these models, and the results have important implications for potential hotspot evolution near convergent margins.

Assessing the Altitude and Dispersion of Volcanic Plumes Using MISR Multi-angle Imaging from Space: Sixteen Years of Volcanic Activity in the Kamchatka Peninsula, Russia

NASA Technical Reports Server (NTRS)

Flower, Verity J. B.; Kahn, Ralph A.

2017-01-01

Volcanic eruptions represent a significant source of atmospheric aerosols and can display local, regional and global effects, impacting earth systems and human populations. In order to assess the relative impacts of these events, accurate plume injection altitude measurements are needed. In this work, volcanic plumes generated from seven Kamchatka Peninsula volcanoes (Shiveluch, Kliuchevskoi, Bezymianny, Tolbachik, Kizimen, Karymsky and Zhupanovsky), were identified using over 16 years of Multi-angle Imaging SpectroRadimeter (MISR) measurements. Eighty-eight volcanic plumes were observed by MISR, capturing 3-25% of reported events at individual volcanoes. Retrievals were most successful where high intensity events persisted over a period of weeks to months. Compared with existing ground and airborne observations, and alternative satellite-based reports compiled by the Global Volcanism Program (GVP), MISR plume height retrievals showed general consistency; the comparison reports appear to be skewed towards the region of highest concentration observed in MISR-constrained vertical plume extent. The report observations display less discrepancy with MISR toward the end of the analysis period, with improvements in the suborbital data likely the result of the deployment of new instrumentation. Conversely, the general consistency of MISR plume heights with conventionally reported observations supports the use of MISR in the ongoing assessment of volcanic activity globally, especially where other types of volcanic plume observations are unavailable. Differences between the northern (Shiveluch, Kliuchevskoi, Bezymianny and Tolbachik) and southern (Kizimen, Karymsky and Zhupanovsky) volcanoes broadly correspond to the Central Kamchatka Depression (CKD) and Eastern Volcanic Front (EVF), respectively, geological sub-regions of Kamchatka distinguished by varying magma composition. For example, by comparison with reanalysis-model simulations of local meteorological conditions, CKD plumes generally were less constrained by mid-tropospheric (< 6 km) layers of vertical stability above the boundary layer, suggesting that these eruptions were more energetic than those in the EVF

Advances in the Validation of Satellite-Based Maps of Volcanic Sulfur Dioxide Plumes

NASA Astrophysics Data System (ADS)

Realmuto, V. J.; Berk, A.; Acharya, P. K.; Kennett, R.

2013-12-01

The monitoring of volcanic gas emissions with gas cameras, spectrometer arrays, tethersondes, and UAVs presents new opportunities for the validation of satellite-based retrievals of gas concentrations. Gas cameras and spectrometer arrays provide instantaneous observations of the gas burden, or concentration along an optical path, over broad sections of a plume, similar to the observations acquired by nadir-viewing satellites. Tethersondes and UAVs provide us with direct measurements of the vertical profiles of gas concentrations within plumes. This presentation will focus on our current efforts to validate ASTER-based maps of sulfur dioxide plumes at Turrialba and Kilauea Volcanoes (located in Costa Rica and Hawaii, respectively). These volcanoes, which are the subjects of comprehensive monitoring programs, are challenging targets for thermal infrared (TIR) remote sensing due the warm and humid atmospheric conditions. The high spatial resolution of ASTER in the TIR (90 meters) allows us to map the plumes back to their source vents, but also requires us to pay close attention to the temperature and emissivity of the surfaces beneath the plumes. Our knowledge of the surface and atmospheric conditions is never perfect, and we employ interactive mapping techniques that allow us to evaluate the impact of these uncertainties on our estimates of plume composition. To accomplish this interactive mapping we have developed the Plume Tracker tool kit, which integrates retrieval procedures, visualization tools, and a customized version of the MODTRAN radiative transfer (RT) model under a single graphics user interface (GUI). We are in the process of porting the RT calculations to graphics processing units (GPUs) with the goal of achieving a 100-fold increase in the speed of computation relative to conventional CPU-based processing. We will report on our progress with this evolution of Plume Tracker. Portions of this research were conducted at the Jet Propulsion Laboratory, California Institute of Technology, under contract to the National Aeronautics and Space Administration.

Transient Plume Model Testing Using LADEE Spacecraft Attitude Control System Operations

NASA Technical Reports Server (NTRS)

Woronowicz, Michael

2011-01-01

We have learned it is conceivable that the Neutral Mass Spectrometer on board the Lunarr Atmosphere Dust Environment Explorer (LADEE) could measure gases from surface-reflected Attitude Control System (ACS) thruster plume. At minimum altitude, the measurement would be maximized, and gravitational influence minimized ("short" time-of-flight (TOF) situation) Could use to verify aspects of thruster plume modeling Model the transient disturbance to NMS measurements due to ACS gases reflected from lunar surface Observe evolution of various model characteristics as measured by NMS Species magnitudes, TOF measurements, angular distribution, species separation effects

Context-dependent olfactory enhancement of optomotor flight control in Drosophila.

PubMed

Chow, Dawnis M; Frye, Mark A

2008-08-01

Sensing and following the chemical plume of food odors is a fundamental challenge faced by many organisms. For flying insects, the task is complicated by wind that distorts the plume and buffets the fly. To maintain an upwind heading, and thus stabilize their orientation in a plume, insects such as flies and moths make use of strong context-specific visual equilibrium reflexes. For example, flying straight requires the regulation of image rotation across the eye, whereas minimizing side-slip and avoiding a collision require regulation of image expansion. In flies, visual rotation stabilizes plume tracking, but rotation and expansion optomotor responses are controlled by separate visual pathways. Are olfactory signals integrated with optomotor responses in a manner dependent upon visual context? We addressed this question by investigating the effect of an attractive food odor on active optomotor flight control. Odorant caused flies both to increase aerodynamic power output and to steer straighter. However, when challenged with wide-field optic flow, odor resulted in enhanced amplitude rotation responses but reduced amplitude expansion responses. For both visual conditions, flies tracked motion signals more closely in odor, an indication of increased saliency. These results suggest a simple search algorithm by which olfactory signals improve the salience of visual stimuli and modify optomotor control in a context-dependent manner, thereby enabling an animal to fly straight up a plume and approach odiferous objects.

Magma source evolution beneath the Caribbean oceanic plateau: New insights from elemental and Sr-Nd-Pb-Hf isotopic studies of ODP Leg 165, Site 1001 basalts

NASA Astrophysics Data System (ADS)

Kerr, A. C.; Pearson, G.; Nowell, G.

2008-12-01

Ocean Drilling Project Leg 165 sampled 38m of the basaltic basement of the Caribbean plate at Site 1001 on the Hess Escarpment. The recovered section consists of 12 basaltic flow units which yield a weighted mean Ar-Ar age of 80.9±0.9 Ma (Sinton et al., 2000). The basalts (6.4-8.5 wt.% MgO) are remarkably homogeneous in composition and are more depleted in incompatible trace elements than N-MORB. Markedly, depleted initial radiogenic isotope ratios reveal a long-term history of depletion. Although the Site 1001 basalts are superficially similar to N-MORB, radiogenic isotopes in conjunction with incompatible trace element ratios show that the basalts have more similarity to the depleted basalts and komatiites of Gorgona Island. This chemical composition strongly implies that the Site 1001 basalts are derived from a depleted mantle plume component and not from depleted ambient upper mantle. Therefore the Site 1001 basalts are, both compositionally and tectonically, a constituent part of the Caribbean oceanic plateau. Mantle melt modelling suggests that the Site 1001 lavas have a composition which is consistent with second-stage melting of compositionally heterogeneous mantle plume source material which had already been melted, most likely to form the 90Ma basalts of the plateau. The prolonged residence (>10m.y.) of residual mantle plume source material below the region, confirms computational model predictions and places significant constraints on tectonic models of Caribbean evolution in the late Cretaceous, and the consequent environmental impact of oceanic plateau volcanism. Reference Sinton, C.W., et al., 2000. Geochronology and petrology of the igneous basement at the lower Nicaraguan Rise, Site 1001. Proceedings of the Ocean Drilling Program, Scientific Results. Leg 165. pp. 233-236.

The role of vision in odor-plume tracking by walking and flying insects.

PubMed

Willis, Mark A; Avondet, Jennifer L; Zheng, Elizabeth

2011-12-15

The walking paths of male cockroaches, Periplaneta americana, tracking point-source plumes of female pheromone often appear similar in structure to those observed from flying male moths. Flying moths use visual-flow-field feedback of their movements to control steering and speed over the ground and to detect the wind speed and direction while tracking plumes of odors. Walking insects are also known to use flow field cues to steer their trajectories. Can the upwind steering we observe in plume-tracking walking male cockroaches be explained by visual-flow-field feedback, as in flying moths? To answer this question, we experimentally occluded the compound eyes and ocelli of virgin P. americana males, separately and in combination, and challenged them with different wind and odor environments in our laboratory wind tunnel. They were observed responding to: (1) still air and no odor, (2) wind and no odor, (3) a wind-borne point-source pheromone plume and (4) a wide pheromone plume in wind. If walking cockroaches require visual cues to control their steering with respect to their environment, we would expect their tracks to be less directed and more variable if they cannot see. Instead, we found few statistically significant differences among behaviors exhibited by intact control cockroaches or those with their eyes occluded, under any of our environmental conditions. Working towards our goal of a comprehensive understanding of chemo-orientation in insects, we then challenged flying and walking male moths to track pheromone plumes with and without visual feedback. Neither walking nor flying moths performed as well as walking cockroaches when there was no visual information available.

The role of vision in odor-plume tracking by walking and flying insects

PubMed Central

Willis, Mark A.; Avondet, Jennifer L.; Zheng, Elizabeth

2011-01-01

SUMMARY The walking paths of male cockroaches, Periplaneta americana, tracking point-source plumes of female pheromone often appear similar in structure to those observed from flying male moths. Flying moths use visual-flow-field feedback of their movements to control steering and speed over the ground and to detect the wind speed and direction while tracking plumes of odors. Walking insects are also known to use flow field cues to steer their trajectories. Can the upwind steering we observe in plume-tracking walking male cockroaches be explained by visual-flow-field feedback, as in flying moths? To answer this question, we experimentally occluded the compound eyes and ocelli of virgin P. americana males, separately and in combination, and challenged them with different wind and odor environments in our laboratory wind tunnel. They were observed responding to: (1) still air and no odor, (2) wind and no odor, (3) a wind-borne point-source pheromone plume and (4) a wide pheromone plume in wind. If walking cockroaches require visual cues to control their steering with respect to their environment, we would expect their tracks to be less directed and more variable if they cannot see. Instead, we found few statistically significant differences among behaviors exhibited by intact control cockroaches or those with their eyes occluded, under any of our environmental conditions. Working towards our goal of a comprehensive understanding of chemo-orientation in insects, we then challenged flying and walking male moths to track pheromone plumes with and without visual feedback. Neither walking nor flying moths performed as well as walking cockroaches when there was no visual information available. PMID:22116754

Plume radiation

NASA Astrophysics Data System (ADS)

Dirscherl, R.

1993-06-01

The electromagnetic radiation originating from the exhaust plume of tactical missile motors is of outstanding importance for military system designers. Both missile- and countermeasure engineer rely on the knowledge of plume radiation properties, be it for guidance/interference control or for passive detection of adversary missiles. To allow access to plume radiation properties, they are characterized with respect to the radiation producing mechanisms like afterburning, its chemical constituents, and reactions as well as particle radiation. A classification of plume spectral emissivity regions is given due to the constraints imposed by available sensor technology and atmospheric propagation windows. Additionally assessment methods are presented that allow a common and general grouping of rocket motor properties into various categories. These methods describe state of the art experimental evaluation techniques as well as calculation codes that are most commonly used by developers of NATO countries. Dominant aspects influencing plume radiation are discussed and a standardized test technique is proposed for the assessment of plume radiation properties that include prediction procedures. These recommendations on terminology and assessment methods should be common to all employers of plume radiation. Special emphasis is put on the omnipresent need for self-protection by the passive detection of plume radiation in the ultraviolet (UV) and infrared (IR) spectral band.

Ground-based and airborne in-situ measurements of the Eyjafjallajökull volcanic aerosol plume in Switzerland in spring 2010

NASA Astrophysics Data System (ADS)

Bukowiecki, N.; Zieger, P.; Weingartner, E.; Jurányi, Z.; Gysel, M.; Neininger, B.; Schneider, B.; Hueglin, C.; Ulrich, A.; Wichser, A.; Henne, S.; Brunner, D.; Kaegi, R.; Schwikowski, M.; Tobler, L.; Wienhold, F. G.; Engel, I.; Buchmann, B.; Peter, T.; Baltensperger, U.

2011-10-01

The volcanic aerosol plume resulting from the Eyjafjallajökull eruption in Iceland in April and May 2010 was detected in clear layers above Switzerland during two periods (17-19 April 2010 and 16-19 May 2010). In-situ measurements of the airborne volcanic plume were performed both within ground-based monitoring networks and with a research aircraft up to an altitude of 6000 m a.s.l. The wide range of aerosol and gas phase parameters studied at the high altitude research station Jungfraujoch (3580 m a.s.l.) allowed for an in-depth characterization of the detected volcanic aerosol. Both the data from the Jungfraujoch and the aircraft vertical profiles showed a consistent volcanic ash mode in the aerosol volume size distribution with a mean optical diameter around 3 ± 0.3 μm. These particles were found to have an average chemical composition very similar to the trachyandesite-like composition of rock samples collected near the volcano. Furthermore, chemical processing of volcanic sulfur dioxide into sulfate clearly contributed to the accumulation mode of the aerosol at the Jungfraujoch. The combination of these in-situ data and plume dispersion modeling results showed that a significant portion of the first volcanic aerosol plume reaching Switzerland on 17 April 2010 did not reach the Jungfraujoch directly, but was first dispersed and diluted in the planetary boundary layer. The maximum PM10 mass concentrations at the Jungfraujoch reached 30 μgm-3 and 70 μgm-3 (for 10-min mean values) duri ng the April and May episode, respectively. Even low-altitude monitoring stations registered up to 45 μgm-3 of volcanic ash related PM10 (Basel, Northwestern Switzerland, 18/19 April 2010). The flights with the research aircraft on 17 April 2010 showed one order of magnitude higher number concentrations over the northern Swiss plateau compared to the Jungfraujoch, and a mass concentration of 320 (200-520) μgm-3 on 18 May 2010 over the northwestern Swiss plateau. The presented data significantly contributed to the time-critical assessment of the local ash layer properties during the initial eruption phase. Furthermore, dispersion models benefited from the detailed information on the volcanic aerosol size distribution and its chemical composition.

Ground-based and airborne in-situ measurements of the Eyjafjallajökull volcanic aerosol plume in Switzerland in spring 2010

NASA Astrophysics Data System (ADS)

Bukowiecki, N.; Zieger, P.; Weingartner, E.; Jurányi, Z.; Gysel, M.; Neininger, B.; Schneider, B.; Hueglin, C.; Ulrich, A.; Wichser, A.; Henne, S.; Brunner, D.; Kaegi, R.; Schwikowski, M.; Tobler, L.; Wienhold, F. G.; Engel, I.; Buchmann, B.; Peter, T.; Baltensperger, U.

2011-04-01

The volcanic aerosol plume resulting from the Eyjafjallajökull eruption in Iceland in April and May 2010 was detected in clear layers above Switzerland during two periods (17-19 April 2010 and 16-19 May 2010). In-situ measurements of the airborne volcanic plume were performed both within ground-based monitoring networks and with a research aircraft up to an altitude of 6000 m a.s.l. The wide range of aerosol and gas phase parameters studied at the high altitude research station Jungfraujoch (3580 m a.s.l.) allowed for an in-depth characterization of the detected volcanic aerosol. Both the data from the Jungfraujoch and the aircraft vertical profiles showed a consistent volcanic ash mode in the aerosol volume size distribution with a mean optical diameter around 3 ± 0.3 μm. These particles were found to have an average chemical composition very similar to the trachyandesite-like composition of rock samples collected near the volcano. Furthermore, chemical processing of volcanic sulfur dioxide into sulfate clearly contributed to the accumulation mode of the aerosol at the Jungfraujoch. The combination of these in-situ data and plume dispersion modeling results showed that a significant portion of the first volcanic aerosol plume reaching Switzerland on 17 April 2010 did not reach the Jungfraujoch directly, but was first dispersed and diluted in the planetary boundary layer. The maximum PM10 mass concentrations at the Jungfraujoch reached 30 μg m-3 and 70 μg m-3 (for 10-min mean values) during the April and May episode, respectively. Even low-altitude monitoring stations registered up to 45 μg m-3 of volcanic ash related PM10 (Basel, Northwestern Switzerland, 18/19 April 2010). The flights with the research aircraft on 17 April 2010 showed one order of magnitude higher number concentrations over the northern Swiss plateau compared to the Jungfraujoch, and a mass concentration of 320 (200-520) μg m-3 on 18 May 2010 over the northwestern Swiss plateau. The presented data significantly contributed to the time-critical assessment of the local ash layer properties during the initial eruption phase. Furthermore, dispersion models benefited from the detailed information on the volcanic aerosol size distribution and its chemical composition.

Plume Impingement Analysis for the European Service Module Propulsion System

NASA Technical Reports Server (NTRS)

Yim, John Tamin; Sibe, Fabien; Ierardo, Nicola

2014-01-01

Plume impingement analyses were performed for the European Service Module (ESM) propulsion system Orbital Maneuvering System engine (OMS-E), auxiliary engines, and reaction control system (RCS) engines. The heat flux from plume impingement on the solar arrays and other surfaces are evaluated. This information is used to provide inputs for the ESM thermal analyses and help determine the optimal configuration for the RCS engines.

Plume-ridge interaction: Shaping the geometry of mid-ocean ridges

NASA Astrophysics Data System (ADS)

Mittelstaedt, Eric L.

Manifestations of plume-ridge interaction are found across the ocean basins. Currently there are interactions between at least 21 hot spots and nearby ridges along 15--20% of the global mid-ocean ridge network. These interactions produce a number of anomalies including the presence of elevated topography, negative gravity anomalies, and anomalous crustal production. One form of anomalous crustal production is the formation of volcanic lineaments between hotspots and nearby mid-ocean ridges. In addition, observations indicate that mantle plumes tend to "capture" nearby mid-ocean ridges through asymmetric spreading, increased ridge propagation, and discrete shifts of the ridge axis, or ridge jumps. The initiation of ridge jumps and the formation of off-axis volcanic lineaments likely involve similar processes and may be closely related. In the following work, I use theoretical and numerical models to quantify the processes that control the formation of volcanic lineaments (Chapter 2), the initiation of mid-ocean ridge jumps associated with lithospheric heating due to magma passing through the plate (Chapter 3), and the initiation of jumps due to an upwelling mantle plume and magmatic heating governed by melt migration (Chapter 4). Results indicate that lineaments and ridge jumps associated with plume-ridge interaction are most likely to occur on young lithosphere. The shape of lineaments on the seafloor is predicted to be controlled by the pattern of lithospheric stresses associated with a laterally spreading, near-ridge mantle plume. Ridge jumps are likely to occur due to magmatic heating alone only in lithosphere ˜1Myr old, because the heating rate required to jump increases with spreading rate and plate age. The added effect of an upwelling plume introduces competing effects that both promote and inhibit ridge jumps. For models where magmatic heating is controlled by melt migration, repeat ridge jumps are predicted to occur as the plume and ridge separate, but only for restricted values of spreading rate, ridge migration rate, and heating rate. Overall, the results suggest that the combined effect of stresses and magmatism associated with plume-ridge interaction can significantly alter plate geometry over time.

Enceladus Hydrothermal Activity

NASA Image and Video Library

2017-04-13

This graphic illustrates how scientists on NASA's Cassini mission think water interacts with rock at the bottom of the ocean of Saturn's icy moon Enceladus, producing hydrogen gas (H2). The Cassini spacecraft detected the hydrogen in the plume of gas and icy material spraying from Enceladus during its deepest and last dive through the plume on Oct. 28, 2015. Cassini also sampled the plume's composition during previous flybys, earlier in the mission. From these observations scientists have determined that nearly 98 percent of the gas in the plume is water vapor, about 1 percent is hydrogen, and the rest is a mixture of other molecules including carbon dioxide, methane and ammonia. The graphic shows water from the ocean circulating through the seafloor, where it is heated and interacts chemically with the rock. This warm water, laden with minerals and dissolved gases (including hydrogen and possibly methane) then pours into the ocean creating chimney-like vents. The hydrogen measurements were made using Cassini's Ion and Neutral Mass Spectrometer, or INMS, instrument, which sniffs gases to determine their composition. The finding is an independent line of evidence that hydrothermal activity is taking place in the Enceladus ocean. Previous results from Cassini's Cosmic Dust Analyzer instrument, published in March 2015, suggested hot water is interacting with rock beneath the ocean; the new findings support that conclusion and indicate that the rock is reduced in its geochemistry. With the discovery of hydrogen gas, scientists can now conclude that there is a source of chemical free energy in Enceladus' ocean. https://photojournal.jpl.nasa.gov/catalog/PIA21442

Can Analysis of Acetylene and Its Biodegradation Products in Enceladus Plumes be Used to Detect the Presence of Sub-Surface Life?

NASA Astrophysics Data System (ADS)

Miller, L. G.; Baesman, S. M.; Oremland, R. S.

2014-12-01

The search for biosignatures of life on Earth includes measurement of the stable isotope fractionation of reactants and products attributed to enzymatic processes and comparison with the often smaller chemical (abiotic) fractionation. We propose that this approach might be applied to study the origin and fate of organic compounds contained in water vapor plumes emanating from Enceladus or other icy bodies, perhaps revealing information about the potential for biology occurring within a sub-surface "habitable" zone. Methanol and C2-hydrocarbons including ethylene, ethane and acetylene (C2H2) have been identified in the plumes of Enceladus. Biological degradation of acetylene proceeds by anaerobic fermentation via acetylene hydratase through acetaldehyde, with a second enzyme (acetaldehyde dismutase) forming acetate and ethanol. We found that incubation of cultures of acetylene-fermenting bacteria exhibit a kinetic isotope effect (KIE) associated with the net removal of C2H2. Consumption of acetylene by both growing and washed-cell cultures of bacteria closely related to Pelobacter acetylenicus (e.g, strain SFB93) was accompanied by a carbon isotopic fractionation of about 2 per mil (KIE = 1.8-2.7 ‰), a result we are examining with other cultures of acetylene fermenters. In addition, we are measuring the carbon isotopic composition of acetaldehyde, ethanol and acetate during fermentation to learn whether these products are fractionated sufficiently, relative to their substrate, to warrant measurement of their isotopic composition in Enceladus (or Europa) plumes to indicate enzymatic activity in liquid environments below the crust of these moons.

Modeling the influence of coupled mass transfer processes on mass flux downgradient of heterogeneous DNAPL source zones

NASA Astrophysics Data System (ADS)

Yang, Lurong; Wang, Xinyu; Mendoza-Sanchez, Itza; Abriola, Linda M.

2018-04-01

Sequestered mass in low permeability zones has been increasingly recognized as an important source of organic chemical contamination that acts to sustain downgradient plume concentrations above regulated levels. However, few modeling studies have investigated the influence of this sequestered mass and associated (coupled) mass transfer processes on plume persistence in complex dense nonaqueous phase liquid (DNAPL) source zones. This paper employs a multiphase flow and transport simulator (a modified version of the modular transport simulator MT3DMS) to explore the two- and three-dimensional evolution of source zone mass distribution and near-source plume persistence for two ensembles of highly heterogeneous DNAPL source zone realizations. Simulations reveal the strong influence of subsurface heterogeneity on the complexity of DNAPL and sequestered (immobile/sorbed) mass distribution. Small zones of entrapped DNAPL are shown to serve as a persistent source of low concentration plumes, difficult to distinguish from other (sorbed and immobile dissolved) sequestered mass sources. Results suggest that the presence of DNAPL tends to control plume longevity in the near-source area; for the examined scenarios, a substantial fraction (43.3-99.2%) of plume life was sustained by DNAPL dissolution processes. The presence of sorptive media and the extent of sorption non-ideality are shown to greatly affect predictions of near-source plume persistence following DNAPL depletion, with plume persistence varying one to two orders of magnitude with the selected sorption model. Results demonstrate the importance of sorption-controlled back diffusion from low permeability zones and reveal the importance of selecting the appropriate sorption model for accurate prediction of plume longevity. Large discrepancies for both DNAPL depletion time and plume longevity were observed between 2-D and 3-D model simulations. Differences between 2- and 3-D predictions increased in the presence of sorption, especially for the case of non-ideal sorption, demonstrating the limitations of employing 2-D predictions for field-scale modeling.

Pyro-cumulonimbus injection of smoke to the stratosphere: Observations and impact of a super blowup in northwestern Canada on 3-4 August 1998

NASA Astrophysics Data System (ADS)

Fromm, Michael; Bevilacqua, Richard; Servranckx, René; Rosen, James; Thayer, Jeffrey P.; Herman, Jay; Larko, David

2005-04-01

We report observations and analysis of a pyro-cumulonimbus event in the midst of a boreal forest fire blowup in Northwest Territories Canada, near Norman Wells, on 3-4 August 1998. We find that this blowup caused a five-fold increase in lower stratospheric aerosol burden, as well as multiple reports of anomalous enhancements of tropospheric gases and aerosols across Europe 1 week later. Our observations come from solar occultation satellites (POAM III and SAGE II), nadir imagers (GOES, AVHRR, SeaWiFS, DMSP), TOMS, lidar, and backscattersonde. First, we provide a detailed analysis of the 3 August eruption of extreme pyro-convection. This includes identifying the specific pyro-cumulonimbus cells that caused the lower stratospheric aerosol injection, and a meteorological analysis. Next, we characterize the altitude, composition, and opacity of the post-convection smoke plume on 4-7 August. Finally, the stratospheric impact of this injection is analyzed. Satellite images reveal two noteworthy pyro-cumulonimbus phenomena: (1) an active-convection cloud top containing enough smoke to visibly alter the reflectivity of the cloud anvil in the Upper Troposphere Lower Stratosphere (UTLS) and (2) a smoke plume, that endured for at least 2 hours, atop an anvil. The smoke pall deposited by the Norman Wells pyro-convection was a very large, optically dense, UTLS-level plume on 4 August that exhibited a mesoscale cyclonic circulation. An analysis of plume color/texture from SeaWiFS data, aerosol index, and brightness temperature establishes the extreme altitude and "pure" smoke composition of this unique plume. We show what we believe to be a first-ever measurement of strongly enhanced ozone in the lower stratosphere mingled with smoke layers. We conclude that two to four extreme pyro-thunderstorms near Norman Wells created a smoke injection of hemispheric scope that substantially increased stratospheric optical depth, transported aerosols 7 km above the tropopause (above ˜430 K potential temperature), and also perturbed lower stratospheric ozone.

LIFE: Life Investigation For Enceladus A Sample Return Mission Concept in Search for Evidence of Life.

PubMed

Tsou, Peter; Brownlee, Donald E; McKay, Christopher P; Anbar, Ariel D; Yano, Hajime; Altwegg, Kathrin; Beegle, Luther W; Dissly, Richard; Strange, Nathan J; Kanik, Isik

2012-08-01

Life Investigation For Enceladus (LIFE) presents a low-cost sample return mission to Enceladus, a body with high astrobiological potential. There is ample evidence that liquid water exists under ice coverage in the form of active geysers in the "tiger stripes" area of the southern Enceladus hemisphere. This active plume consists of gas and ice particles and enables the sampling of fresh materials from the interior that may originate from a liquid water source. The particles consist mostly of water ice and are 1-10 μ in diameter. The plume composition shows H(2)O, CO(2), CH(4), NH(3), Ar, and evidence that more complex organic species might be present. Since life on Earth exists whenever liquid water, organics, and energy coexist, understanding the chemical components of the emanating ice particles could indicate whether life is potentially present on Enceladus. The icy worlds of the outer planets are testing grounds for some of the theories for the origin of life on Earth. The LIFE mission concept is envisioned in two parts: first, to orbit Saturn (in order to achieve lower sampling speeds, approaching 2 km/s, and thus enable a softer sample collection impact than Stardust, and to make possible multiple flybys of Enceladus); second, to sample Enceladus' plume, the E ring of Saturn, and the Titan upper atmosphere. With new findings from these samples, NASA could provide detailed chemical and isotopic and, potentially, biological compositional context of the plume. Since the duration of the Enceladus plume is unpredictable, it is imperative that these samples are captured at the earliest flight opportunity. If LIFE is launched before 2019, it could take advantage of a Jupiter gravity assist, which would thus reduce mission lifetimes and launch vehicle costs. The LIFE concept offers science returns comparable to those of a Flagship mission but at the measurably lower sample return costs of a Discovery-class mission.

Stomatal response of swordfern to volcanogenic CO2 and SO2 from Kilauea volcano

NASA Astrophysics Data System (ADS)

Tanner, Lawrence H.; Smith, David L.; Allan, Amanda

2007-08-01

The experimentally determined relationship between atmospheric pCO2 and plant stomata has been used to interpret large but transient changes in atmospheric composition, such as may have resulted from the eruptions of flood basalt. However, this relationship has not been tested in the field, i.e. in the vicinity of active volcanoes, to examine the specific effects of volcanogenic emissions. Moreover, the interpretation of paleoatmospheric pCO2 from fossil stomatal data assumes that the stomatal response resulted solely from variation in pCO2 and ignores the potential effect of outgassed SO2. We hypothesize that volcanogenic SO2 also has a significant effect on leaf stomata and test this hypothesis by measuring the stomatal index of the common swordfern (Nephrolepis exaltata) in the plumes of the actively outgassing vents of Kilauea volcano. We find that, compared to control locations, stomatal index is lowest at sample sites in the plume of Halema'uma'u Crater, where concentrations of both CO2 and SO2 are much higher than background. However, sites located directly in the plume of Pu'u O'o, where SO2 levels are high, but CO2 levels are not, also yield low values of stomatal index. We propose that shifts in the stomatal index of fossil leaves may record transient atmospheric increases in both SO2 and CO2, such as may be caused by eruptions of flood basalts. Calculations of pCO2 based on stomatal frequency are likely to be exaggerated.

Iron persistence in a distal hydrothermal plume supported by dissolved-particulate exchange

NASA Astrophysics Data System (ADS)

Fitzsimmons, Jessica N.; John, Seth G.; Marsay, Christopher M.; Hoffman, Colleen L.; Nicholas, Sarah L.; Toner, Brandy M.; German, Christopher R.; Sherrell, Robert M.

2017-02-01

Hydrothermally sourced dissolved metals have been recorded in all ocean basins. In the oceans' largest known hydrothermal plume, extending westwards across the Pacific from the Southern East Pacific Rise, dissolved iron and manganese were shown by the GEOTRACES program to be transported halfway across the Pacific. Here, we report that particulate iron and manganese in the same plume also exceed background concentrations, even 4,000 km from the vent source. Both dissolved and particulate iron deepen by more than 350 m relative to 3He--a non-reactive tracer of hydrothermal input--crossing isopycnals. Manganese shows no similar descent. Individual plume particle analyses indicate that particulate iron occurs within low-density organic matrices, consistent with its slow sinking rate of 5-10 m yr-1. Chemical speciation and isotopic composition analyses reveal that particulate iron consists of Fe(III) oxyhydroxides, whereas dissolved iron consists of nanoparticulate Fe(III) oxyhydroxides and an organically complexed iron phase. The descent of plume-dissolved iron is best explained by reversible exchange onto slowly sinking particles, probably mediated by organic compounds binding iron. We suggest that in ocean regimes with high particulate iron loadings, dissolved iron fluxes may depend on the balance between stabilization in the dissolved phase and the reversibility of exchange onto sinking particles.

Diagnostics of Laser Produced Plume Under Carbon Nanotube Growth Conditions

NASA Technical Reports Server (NTRS)

Arepalli, Sivaram; Nikolaev, Pavel; Holmes, William; Scott, Carl D.

1999-01-01

This paper presents diagnostic data obtained from the plume of a graphite composite target during carbon nanotube production by the double-pulse laser oven method. The insitu emission spectrum (300 to 650 nm) is recorded at different locations upstream of the target and at different delay times from the lasers (IR and green). Spectral features are identified as emissions from C2 (Swan System: a (sup 3)pi(sub g) - delta (sup 3)pi(sub u) and C3 (Comet Head System: A (sup 1)pi(sub u) - chi (sup 1)sigma(sub u) (sup +). Experimental spectra are compared with computed spectra to estimate vibrational temperatures of excited state C2 in the range of 2500 to 4000 kappa The temporal evolution of the 510 nm band of C2 is monitored for two target positions in various locations which shows confinement of the plume in the inner tube and increase in plume velocity with temperature. The excitation spectra of C2 are obtained by using a dye laser to pump the (0,1) transition of the Swan System and collecting the Laser Induced Fluorescence signal from C2 These are used to obtain "ground-state" rotational and vibrational temperatures which are close to the oven temperature. Images of the plume are also collected and are compared with the spectral measurements.

Correlation of plume opacity with particles and sulfates from boilers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lou, J.C.; Lee, M.; Chen, K.S.

1997-07-01

The effects of emission concentrations of particulate matters and sulfates on plume opacity are investigated by in situ measurements. The studies are conducted for three processes of two coal-fired plants and one oil-fired that are all equipped with electrostatic precipitators. Flue-gas sampling and analysis include the concentrations of particles and total water soluble sulfates, particle size distribution, and flue-gas composition; while in-stack and out-of-stack opacities are determined by a transmissometer and certified smoke inspectors, respectively. Experimental results show that plume opacity outside the stack linearly correlates well with the in-stack opacity. The mixing of hot flue gas with cold ambientmore » air would result in the condensation of hygroscopic sulfuric acid aerosols and an increase about 1.6% out of typical 15--25% measured opacity. An empirical equation similar to the Beer-Lambert-Bouger form is derived for predicting the plume opacity in terms of the stack diameter and the concentrations of particles and total water soluble sulfates. Good comparisons are achieved between predictions by the empirical equation and other available field data.« less

John F. Kennedy Space Center's Technology Development and Application 2006-2007 Report

NASA Technical Reports Server (NTRS)

2008-01-01

Topics covered include: Reversible Chemochromic Hydrogen Detectors; Determining Trajectory of Triboelectrically Charged Particles, Using Discrete Element Modeling; Using Indium Tin Oxide To Mitigate Dust on Viewing Ports; High-Performance Polyimide Powder Coatings; Controlled-Release Microcapsules for Smart Coatings for Corrosion Applications; Aerocoat 7 Replacement Coatings; Photocatalytic Coatings for Exploration and Spaceport Design; New Materials for the Repair of Polyimide Electrical Wire Insulation; Commodity-Free Calibration; Novel Ice Mitigation Methods; Crack Offset Measurement With the Projected Laser Target Device; New Materials for Structural Composites and Protective Coatings; Fire Chemistry Testing of Spray-On Foam Insulation (SOFI); Using Aerogel-Based Insulation Material To Prevent Foam Loss on the Liquid-Hydrogen Intertank; Particle Ejection and Levitation Technology (PELT); Electrostatic Characterization of Lunar Dust; Numerical Analysis of Rocket Exhaust Cratering; RESOLVE Projects: Lunar Water Resource Demonstration and Regolith Volatile Characterization; Tribocharging Lunar Soil for Electrostatic Beneficiation; Numerically Modeling the Erosion of Lunar Soil by Rocket Exhaust Plumes; Trajectory Model of Lunar Dust Particles; Using Lunar Module Shadows To Scale the Effects of Rocket Exhaust Plumes; Predicting the Acoustic Environment Induced by the Launch of the Ares I Vehicle; Measuring Ultrasonic Acoustic Velocity in a Thin Sheet of Graphite Epoxy Composite; Hail Size Distribution Mapping; Launch Pad 39 Hail Monitor Array System; Autonomous Flight Safety System - Phase III; The Photogrammetry Cube; Bird Vision System; Automating Range Surveillance Through Radio Interferometry and Field Strength Mapping Techniques; Next-Generation Telemetry Workstation; GPS Metric Tracking Unit; and Space-Based Range.

Rethinking geochemical feature of the Afar and Kenya mantle plumes and geodynamic implications

NASA Astrophysics Data System (ADS)

Meshesha, Daniel; Shinjo, Ryuichi

2008-09-01

We discuss the spatial and temporal variation in the geochemistry of mantle sources which were sampled by the Eocene to Quaternary mafic magmas in the vicinity of the Afar and Kenya plume upwelling zones, East Africa. Despite the contributions of lithospheric and crustal sources, carefully screened Eocene to Quaternary mafic lavas display wide range of Sr-Nd-Pb isotopic and incompatible trace elemental compositions that can be attributed to significant intraplume heterogeneity. The geochemical variations reflect the involvement of at least four mantle plume components as sources for the northeastern Africa magmatism: (1) isotopically depleted but trace element-enriched component; (2) component characterized by radiogenic Pb isotope signatures (HIMU?); (3) enriched mantle-like component; and (4) high-3He/4He-type (as HT2-type basalts) plume component. The first component disappears in the Miocene-Quaternary magmatism, and the second component is hardly recognized after the eruption of Miocene basalt in southern Ethiopia. Plume-unrelated depleted asthenosphere starts to involve at a nascent stage of seafloor spreading centers in the Red Sea and Gulf of Aden. The other two-plume components have persisted from the late Eocene to present, but their proportions have changed through time and space. We propose a model of multiple impingements of plumelets within the broad upwelling zone connected to the African Superplume in the lower mantle beneath southern Africa. The plumelet contains a matrix of high-3He/4He-type component with blobs, streaks, or ribbons of other components.

On-board Optical Spectrometry for Detection of Mixture Ratio and Eroded Materials in Rocket Engine Exhaust Plume

NASA Technical Reports Server (NTRS)

Barkhoudarian, Sarkis; Kittinger, Scott

2006-01-01

Optical spectrometry can provide means to characterize rocket engine exhaust plume impurities due to eroded materials, as well as combustion mixture ratio without any interference with plume. Fiberoptic probes and cables were designed, fabricated and installed on Space Shuttle Main Engines (SSME), allowing monitoring of the plume spectra in real time with a Commercial of the Shelf (COTS) fiberoptic spectrometer, located in a test-stand control room. The probes and the cables survived the harsh engine environments for numerous hot-fire tests. When the plume was seeded with a nickel alloy powder, the spectrometer was able to successfully detect all the metallic and OH radical spectra from 300 to 800 nanometers.

From Purgatory to Paradise: The Volatile Life of Hawaiian Magma

NASA Astrophysics Data System (ADS)

Marske, J. P.; Hauri, E. H.; Trusdell, F.; Garcia, M. O.; Pietruszka, A. J.

2014-12-01

Variations in radiogenic isotope ratios and magmatic volatile abundances (e.g., CO2 or H2O) in Hawaiian lavas reveal key processes within a deep-seated mantle plume (e.g., mantle heterogeneity, source lithology, partial melting, and magma degassing). Shield-stage Hawaiian lavas likely originate from a mixed plume source containing peridotite and recycled oceanic crust (pyroxenite) based on variations of radiogenic isotopes (e.g., 206Pb/204Pb). The mantle source region may also be heterogeneous with respect to volatile contents, yet the link between pre-eruptive volatile budgets and mantle source lithology in the Hawaiian plume is poorly constrained due to shallow magmatic degassing and mixing. Here, we use a novel approach to investigate this link using Os isotopic ratios, and major, trace, and volatile elements in olivines and mineral-hosted melt inclusions (MIs) from 34 samples from Koolau, Mauna Loa, Hualalai, Kilauea, and Loihi. These samples reveal a strong correlation between volatile contents in olivine-hosted MIs and Os isotopes of the same olivines, in which lavas that originated from greater proportions of recycled oceanic crust/pyroxenite (i.e. 'Loa' chain volcanoes: Koolau, Mauna Loa, Loihi) have MIs with the lower H2O, F, and Cl contents than 'Kea' chain volcanoes (i.e. Kilauea) that contain greater amounts of peridotite in the source region. No correlation is observed with CO2 or S. The depletion of fluid-mobile elements (H2O, F, and Cl) in 'Loa' chain volcanoes indicates ancient dehydrated oceanic crust is a plume component that controls much of the compositional variation of Hawaiian Volcanoes. The presence of dehydrated recycled mafic material in the plume source suggests that subduction effectively devolatilizes the mafic part of the oceanic crust. These results are similar to the observed shifts in H2O/Ce ratios near the Easter and Samoan hotspots [1,2]. Thus, it appears that multiple hotspots may record relative H2O depletions and possibly other volatiles. [1] Dixon et al. 2002, Nature 420:385-89 [2] Workman et al. 2006, EPSL 241:932-51

Experimental Melting Study of Basalt-Peridotite Hybrid Source: Melting model of Hawaiian plume

NASA Astrophysics Data System (ADS)

Takahashi, E.; Gao, S.

2015-12-01

Eclogite component entrained in ascending plume is considered to be essentially important in producing flood basalts (e.g., Columbia River basalt, Takahashi et al., 1998 EPSL), alkalic OIBs (e.g., Kogiso et al.,2003), ferro-picrites (Tuff et al.,2005) and Hawaiian shield lavas (e.g., Hauri, 1996; Takahashi & Nakajima, 2002, Sobolev et al.,2005). Size of the entrained eclogite, which controls the reaction rates with ambient peridotite, however, is very difficult to constrain using geophysical observation. Among Hawaiian shield volcanoes, Koolau is the most enriched end-member in eclogite component (Frey et al, 1994). Reconstruction of Koolau volcano based on submarine study on Nuuanu landslide (AGU Monograph vol.128, 2002, Takahashi Garcia Lipman eds.) revealed that silica-rich tholeiite appeared only at the last stage (Makapuu stage) of Koolau volcano. Chemical compositions of lavas as well as isotopes change abruptly and coherently across a horizon (Shinozaki et al. and Tanaka et al. ibid.). Based on these observation, Takahashi & Nakajima (2002 ibid) proposed that the Makapuu stage lava in Koolau volcano was supplied from a single large eclogite block. In order to study melting process in Hawaiian plume, high-pressure melting experiments were carried out under dry and hydrous conditions with layered eclogite/peridotite starting materials. Detail of our experiments will be given by Gao et al (2015 AGU). Combined previous field observation with new set of experiments, we propose that variation in SiO2 among Hawaiian tholeiites represent varying degree of wall-rock interaction between eclogite and ambient peridotite. Makapuu stage lavas in Koolau volcano represents eclogite partial melts formed at ~3 GPa with various amount of xenocrystic olivines derived from Pacific plate. In other words, we propose that "primary magma" in the melting column of Hawaiian plume ranges from basaltic andesite to ferro-picrite depending on the lithology of the source. Solidus of peridotite lowers significantly due to FeO, TiO2, K2O from eclogites thus PMT of Hawaiian plume may be ~1450C which is siginificantly lower than current estimates (e.g., Herzberg, 2006).

Melt migration and mantle chromatography, 2: a time-series Os isotope study of Mauna Loa volcano, Hawaii

NASA Astrophysics Data System (ADS)

Hauri, Erik H.; Kurz, Mark D.

1997-12-01

We have determined the major element, trace element, and Os isotopic compositions of a stratigraphic suite of tholeiitic basalts spanning >30,000 years of the eruptive history of Mauna Loa volcano. Good correlations are observed between Os isotopes and the isotopes of Sr, Nd, Pb and He. In addition, the isotopes correlate with fractionation-corrected major element abundances within this single volcano, and provide a record of increased melting of mafic material with time at Mauna Loa. Chromatographic element fractionation during melt transport is shown to be negligible based on the good correlations of the isotopes of the compatible element Os with the other incompatible element tracers. The temporal variation at Mauna Loa is best described by the translation of the volcano over a Hawaiian plume which is radially zoned in composition. The radial zonation is a predicted consequence of thermal entrainment during flow in a mantle plume conduit.

Tritium plume dynamics in the shallow unsaturated zone in an arid environment

USGS Publications Warehouse

Maples, S.R.; Andraski, Brian J.; Stonestrom, David A.; Cooper, C.A.; Pohll, G.; Michel, R.L.

2014-01-01

The spatiotemporal variability of a tritium plume in the shallow unsaturated zone and the mechanisms controlling its transport were evaluated during a 10-yr study. Plume movement was minimal and its mass declined by 68%. Upward-directed diffusive-vapor tritium fluxes and radioactive decay accounted for most of the observed plume-mass declines.Effective isolation of tritium (3H) and other contaminants at waste-burial facilities requires improved understanding of transport processes and pathways. Previous studies documented an anomalously widespread (i.e., theoretically unexpected) distribution of 3H (>400 m from burial trenches) in a dry, sub-root-zone gravelly layer (1–2-m depth) adjacent to a low-level radioactive waste (LLRW) burial facility in the Amargosa Desert, Nevada, that closed in 1992. The objectives of this study were to: (i) characterize long-term, spatiotemporal variability of 3H plumes; and (ii) quantify the processes controlling 3H behavior in the sub-root-zone gravelly layer beneath native vegetation adjacent to the facility. Geostatistical methods, spatial moment analyses, and mass flux calculations were applied to a spatiotemporally comprehensive, 10-yr data set (2001–2011). Results showed minimal bulk-plume advancement during the study period and limited Fickian spreading of mass. Observed spreading rates were generally consistent with theoretical vapor-phase dispersion. The plume mass diminished more rapidly than would be expected from radioactive decay alone, indicating net efflux from the plume. Estimates of upward 3H efflux via diffusive-vapor movement were >10× greater than by dispersive-vapor or total-liquid movement. Total vertical fluxes were >20× greater than lateral diffusive-vapor fluxes, highlighting the importance of upward migration toward the land surface. Mass-balance calculations showed that radioactive decay and upward diffusive-vapor fluxes contributed the majority of plume loss. Results indicate that plume losses substantially exceeded any continuing 3H contribution to the plume from the LLRW facility during 2001 to 2011 and suggest that the widespread 3H distribution resulted from transport before 2001.

EM Modelling of RF Propagation Through Plasma Plumes

NASA Astrophysics Data System (ADS)

Pandolfo, L.; Bandinelli, M.; Araque Quijano, J. L.; Vecchi, G.; Pawlak, H.; Marliani, F.

2012-05-01

Electric propulsion is a commercially attractive solution for attitude and position control of geostationary satellites. Hall-effect ion thrusters generate a localized plasma flow in the surrounding of the satellite, whose impact on the communication system needs to be qualitatively and quantitatively assessed. An electromagnetic modelling tool has been developed and integrated into the Antenna Design Framework- ElectroMagnetic Satellite (ADF-EMS). The system is able to guide the user from the plume definition phases through plume installation and simulation. A validation activity has been carried out and the system has been applied to the plume modulation analysis of SGEO/Hispasat mission.

The 48 Ma Koko Guyot: Early Indications of Temporal Changes in the Composition of the Hawaiian Plume?

NASA Astrophysics Data System (ADS)

Thompson, P. M.; Kempton, P. D.; Saunders, A. D.

2002-12-01

The 48 Ma Koko Guyot is the youngest Emperor Seamount drilled during ODP Leg 197. Leg 197 drilled 278 m into a sequence of 15 lava flows and hyaloclastites, with subordinate amounts of volcaniclastic sandstone and limestone. The sampled lava flows are mainly tholeiitic to transitional basalts and dolerites, with some intercalated alkalic basalts. Thus, the lavas sampled at Koko Guyot resemble the late shield stage of a modern-day Hawaiian volcano, being dominantly tholeiitic in character. The alkalic basalts generally display higher Zr and TiO2 for a given MgO compared to the tholeiites. The degree of scatter for most incompatible elements when plotted against MgO implies that the lavas do not define one liquid line of descent: several parent magma compositions must therefore be invoked. The lavas from Koko have Sr, Nd, Pb and Hf isotope compositions that are the most Hawaiian-like of the Emperor Seamounts that have been studied, displaying similar ɛ Nd to Mauna Kea. Our new data are consistent with the suggestion from trace elements that several different source compositions are required in the genesis of the Koko lavas. The involvement of at least two components is suspected from the apparently linear array in ɛ Hf-ɛ Nd space, which is also indicated by Pb and Sr isotope data. This linear array in ɛ Hf-ɛ Nd space defines a steeper slope than that of Recent Hawaiian magma types, which suggests a fundamental source difference between Koko and modern-day Hawaii. The shallower slope of Hawaiian volcanoes is thought to indicate the involvement of recycled pelagic sediment in the genesis of Hawaiian lavas (Blichert-Toft et al., 1999). Thus, preliminary data from the Koko Guyot suggest that the composition of the Hawaiian plume has changed in composition over time. The causes of this temporal variation are unknown, but may result from changes in the amount of pelagic sediment recycled from the deep plume source. Blichert-Toft, J., Frey, F.A. and Albarède, F., 1999. Hf isotope evidence for pelagic sediments in the source of Hawaiian basalts. Science, 285, 879-882.

Simulation of Europa's water plume .

NASA Astrophysics Data System (ADS)

Lucchetti, A.; Cremonese, G.; Schneider, N. M.; Plainaki, C.; Mazzotta Epifani, E.; Zusi, M.; Palumbo, P.

Plumes on Europa would be extremely interesting science and mission targets, particularly due to the unique opportunity to obtain direct information on the subsurface composition, thereby addressing Europa's potential habitability. The existence of water plume on the Jupiter's moon Europa has been long speculated until the recent discover. HST imaged surpluses of hydrogen Lyman alpha and oxygen emissions above the southern hemisphere in December 2012 that are consistent with two 200 km high plumes of water vapor (Roth et al. 2013). In previous works ballistic cryovolcanism has been considered and modeled as a possible mechanism for the formation of low-albedo features on Europa's surface (Fagents et al. 2000). Our simulation agrees with the model of Fagents et al. (2000) and consists of icy particles that follow ballistic trajectories. The goal of such an analysis is to define the height, the distribution and the extension of the icy particles falling on the moon's surface as well as the thickness of the deposited layer. We expect to observe high albedo regions in contrast with the background albedo of Europa surface since we consider that material falling after a cryovolcanic plume consists of snow. In order to understand if this phenomenon is detectable we convert the particles deposit in a pixel image of albedo data. We consider also the limb view of the plume because, even if this detection requires optimal viewing geometry, it is easier detectable in principle against sky. Furthermore, we are studying the loss rates due to impact electron dissociation and ionization to understand how these reactions decrease the intensity of the phenomenon. We expect to obtain constraints on imaging requirements necessary to detect potential plumes that could be useful for ESA's JUICE mission, and in particular for the JANUS camera (Palumbo et al. 2014).

The INMS Case for Habitability at Enceladus

NASA Astrophysics Data System (ADS)

Waite, J. Hunter; Glein, Chris; Perryman, Rebecca; Magee, Brian; Lunine, Jonathan; Perry, Mark; Grimes, Jacob; Miller, Greg; Bolton, Scott; Miller, Kelly

2017-04-01

Cassini carried out 22 flybys of Enceladus. During seven of these flybys (E2, E3, E5, E7, E14, E17, E18, and E21) the Cassini Ion Neutral Mass Spectrometer obtained important information about the composition of the plume. The data sets will be reviewed with an emphasis on what we have learned about the characteristics of the internal ocean and what this tells us about the potential habitability of Enceladus. Particular emphasis will be given to the recent E21 observations that were specifically targeted to the measurement of H2 gas in the plume.

Task 1: Correlation of satellite and ground data in air pollution studies. Task 2: Investigation to relate the chlorophyll and suspended sediment content in the waters of the lower Chesapeake Bay to ERTS-1 imagery. Task 3: The use of ERTS-1 to more fully utilize and apply marine station data to the study of productivity along the Eastern Shelf expanded waters of the United States

NASA Technical Reports Server (NTRS)

Copeland, G. E. (Principal Investigator); Bandy, A. R.; Fleischer, P.; Ludwick, J. C. (Principal Investigator); Hanna, W. J.; Gosink, T. A.; Bowker, D. W.; Marshall, H. G. (Principal Investigator)

1972-01-01

The author has identified the following significant results. Analysis of U-2 imagery of CARETS site indicates smoke plumes can be easily detected. First look at selected ERTS-1 color composites demonstrates plumes from forest fires can be detected.

Gas- and Particle-phase Chemical Composition Measurements Onboard the G1 Research Aircraft during the CARES Campaign

NASA Astrophysics Data System (ADS)

Shilling, J. E.; Alexander, L.; Jayne, J.; Fortner, E.

2010-12-01

An Aerodyne High Resolution Aerosol Mass Spectrometer (AMS) and an Ionicon Proton Transfer Reaction Mass Spectrometer (PTRMS) were deployed on the G1 research aircraft during the CARES campaign in Sacramento, CA to investigate aerosol gas- and particle-phase chemical composition. Preliminary analysis of PTRMS data suggests that biogenic volatile organic compounds (VOCs), particularly isoprene, dominate the region with anthropogenic VOCs, such as benzene and toluene, providing much smaller contributions to the VOC pool. Data from the AMS shows that the particle phase is dominated by organic material with smaller concentrations of ammonium sulfate and ammonium nitrate observed. Organic particle mass concentration strongly correlated with isoprene and gas-phase isoprene oxidation products, suggesting isoprene chemistry is largely controlling the organic aerosol loading in the area. The chemical evolution of the plume as it traveled downwind from Sacramento and into the foothills will also be discussed.

Temporal evolution of the Kerguelen plume: geochemical evidence from ˜38 to 82 Ma lavas forming the Ninetyeast Ridge

NASA Astrophysics Data System (ADS)

Frey, Frederick A.; Weis, Dominique

1995-08-01

Basaltic basement has been recovered by deep-sea drilling at seven sites on the linear Ninetyeast Ridge in the eastern Indian Ocean. Studies of the recovered lavas show that this ridge formed from ~ 82 to 38 Ma as a series of subaerial volcanoes that were created by the northward migration of the Indian Plate over a fixed magma source in the mantle. The Sr, Nd and Pb isotopic ratios of lavas from the Ninetyeast Ridge range widely, but they largely overlap with those of lavas from the Kerguelen Archipelago, thereby confirming previous inferences that the Kerguelen plume was an important magma source for the Ninetyeast Ridge. Particularly important are the ~ 81 Ma Ninetyeast Ridge lavas from DSDP Site 216 which has an anomalous subsidence history (Coffin 1992). These lavas are FeTi-rich tholeiitic basalts with isotopic ratios that overlap with those of highly alkalic, Upper Miocene lavas in the Kerguelen Archipelago. The isotopic characteristics of the latter which erupted in an intraplate setting have been proposed to be the purest expression of the Kerguelen plume (Weis et al. 1993a,b). Despite the overlap in isotopic ratios, there are important compositional differences between lavas erupted on the Ninetyeast Ridge and in the Kerguelen Archipelago. The Ninetyeast Ridge lavas are dominantly tholeiitic basalts with incompatible element abundance ratios, such as La/Yb and Zr/Nb, which are intermediate between those of Indian Ocean MORB (mid-ocean ridge basalt) and the transitional to alkalic basalts erupted in the Kerguelen Archipelago. These compositional differences reflect a much larger extent of melting for the Ninetyeast Ridge lavas, and the proximity of the plume to a spreading ridge axis. This tectonic setting contrasts with that of the recent alkalic lavas in the Kerguelen Archipelago which formed beneath the thick lithosphere of the Kerguelen Plateau. From ~ 82 to 38 Ma there was no simple, systematic temporal variation of Sr, Nd and Pb isotopic ratios in Ninetyeast Ridge lavas. Therefore all of the isotopic variability cannot be explained by aging of a compositionally uniform plume. Although Class et al. (1993) propose that some of the isotopic variations reflect such aging, we infer that most of the isotopic heterogeneity in lavas from the Ninetyeast Ridge and Kerguelen Archipelago can be explained by mixing of the Kerguelen plume with a depleted MORB-like mantle component. However, with this interpretation some of the youngest, 42-44 Ma, lavas from the southern Ninetyeast Ridge which have206pb/204Pb ratios exceeding those in Indian Ocean MORB and Kerguelen Archipelago lavas require a component with higher206Pb/204Pb, such as that expressed in lavas from St. Paul Island.

Active Volcanic Plumes on Io

NASA Technical Reports Server (NTRS)

1997-01-01

This color image, acquired during Galileo's ninth orbit around Jupiter, shows two volcanic plumes on Io. One plume was captured on the bright limb or edge of the moon (see inset at upper right), erupting over a caldera (volcanic depression) named Pillan Patera after a South American god of thunder, fire and volcanoes. The plume seen by Galileo is 140 kilometers (86 miles) high and was also detected by the Hubble Space Telescope. The Galileo spacecraft will pass almost directly over Pillan Patera in 1999 at a range of only 600 kilometers (373 miles).

The second plume, seen near the terminator (boundary between day and night), is called Prometheus after the Greek fire god (see inset at lower right). The shadow of the 75-kilometer (45- mile) high airborne plume can be seen extending to the right of the eruption vent. The vent is near the center of the bright and dark rings. Plumes on Io have a blue color, so the plume shadow is reddish. The Prometheus plume can be seen in every Galileo image with the appropriate geometry, as well as every such Voyager image acquired in 1979. It is possible that this plume has been continuously active for more than 18 years. In contrast, a plume has never been seen at Pillan Patera prior to the recent Galileo and Hubble Space Telescope images.

North is toward the top of the picture. The resolution is about 6 kilometers (3.7 miles) per picture element. This composite uses images taken with the green, violet and near infrared filters of the solid state imaging (CCD) system on NASA's Galileo spacecraft. The images were obtained on June 28, 1997, at a range of more than 600,000 kilometers (372,000 miles).

The Jet Propulsion Laboratory, Pasadena, CA manages the Galileo mission for NASA's Office of Space Science, Washington, DC. JPL is an operating division of California Institute of Technology (Caltech).

This image and other images and data received from Galileo are posted on the World Wide Web, on the Galileo mission home page at URL http://galileo.jpl.nasa.gov. Background information and educational context for the images can be found at URL http://www.jpl.nasa.gov/galileo/sepo

Zone radiometer measurements on a model rocket exhaust plume

NASA Technical Reports Server (NTRS)

1972-01-01

Radiometer for analytical prediction of rocket plume-to-booster thermal radiation and convective heating is described. Applications for engine combustion analysis, incineration, and pollution control by high temperature processing are discussed. Illustrations of equipment are included.

The Effect of Reaction Control System Thruster Plume Impingement on Orion Service Module Solar Array Power Production

NASA Technical Reports Server (NTRS)

Bury, Kristen M.; Kerslake, Thomas W.

2008-01-01

NASA's new Orion Crew Exploration Vehicle has geometry that orients the reaction control system (RCS) thrusters such that they can impinge upon the surface of Orion's solar array wings (SAW). Plume impingement can cause Paschen discharge, chemical contamination, thermal loading, erosion, and force loading on the SAW surface, especially when the SAWs are in a worst-case orientation (pointed 45 towards the aft end of the vehicle). Preliminary plume impingement assessment methods were needed to determine whether in-depth, timeconsuming calculations were required to assess power loss. Simple methods for assessing power loss as a result of these anomalies were developed to determine whether plume impingement induced power losses were below the assumed contamination loss budget of 2 percent. This paper details the methods that were developed and applies them to Orion's worst-case orientation.

The Effect of Reaction Control System Thruster Plume Impingement on Orion Service Module Solar Array Power Production

NASA Astrophysics Data System (ADS)

Bury, Kristen M.; Kerslake, Thomas W.

2008-06-01

NASA's new Orion Crew Exploration Vehicle has geometry that orients the reaction control system (RCS) thrusters such that they can impinge upon the surface of Orion's solar array wings (SAW). Plume impingement can cause Paschen discharge, chemical contamination, thermal loading, erosion, and force loading on the SAW surface, especially when the SAWs are in a worst-case orientation (pointed 45 towards the aft end of the vehicle). Preliminary plume impingement assessment methods were needed to determine whether in-depth, timeconsuming calculations were required to assess power loss. Simple methods for assessing power loss as a result of these anomalies were developed to determine whether plume impingement induced power losses were below the assumed contamination loss budget of 2 percent. This paper details the methods that were developed and applies them to Orion's worst-case orientation.

Ni, Cu, Au, and platinum-group element contents of sulphides associated with intraplate magmatism: A synthesis

USGS Publications Warehouse

Barnes, S.-J.; Zientek, M.L.; Severson, M.J.

1997-01-01

The tectonic setting of intraplate magmas, typically a plume intersecting a rift, is ideal for the development of Ni - Cu - platinum-group element-bearing sulphides. The plume transports metal-rich magmas close to the mantle - crust boundary. The interaction of the rift and plume permits rapid transport of the magma into the crust, thus ensuring that no sulphides are lost from the magma en route to the crust. The rift may contain sediments which could provide the sulphur necessary to bring about sulphide saturation in the magmas. The plume provides large volumes of mafic magma; thus any sulphides that form can collect metals from a large volume of magma and consequently the sulphides will be metal rich. The large volume of magma provides sufficient heat to release large quantities of S from the crust, thus providing sufficient S to form a large sulphide deposit. The composition of the sulphides varies on a number of scales: (i) there is a variation between geographic areas, in which sulphides from the Noril'sk - Talnakh area are the richest in metals and those from the Muskox intrusion are poorest in metals; (ii) there is a variation between textural types of sulphides, in which disseminated sulphides are generally richer in metals than the associated massive and matrix sulphides; and (iii) the massive and matrix sulphides show a much wider range of compositions than the disseminated sulphides, and on the basis of their Ni/Cu ratio the massive and matrix sulphides can be divided into Cu rich and Fe rich. The Cu-rich sulphides are also enriched in Pt, Pd, and Au; in contrast, the Fe-rich sulphides are enriched in Fe, Os, Ir, Ru, and Rh. Nickel concentrations are similar in both. Differences in the composition between the sulphides from different areas may be attributed to a combination of differences in composition of the silicate magma from which the sulphides segregated and differences in the ratio of silicate to sulphide liquid (R factors). The higher metal content of the disseminated sulphides relative to the massive and matrix sulphides may be due to the fact that the disseminated sulphides equilibrated with a larger volume of magma than massive and matrix sulphides. The difference in composition between the Cu- and Fe-rich sulphides may be the result of the fractional crystallization of monosulphide solid solution from a sulphide liquid, with the Cu-rich sulphides representing the liquid and the Fe-rich sulphides representing the cumulate.

Regimes of plume-slab interaction and consequences for hotspot volcanism

NASA Astrophysics Data System (ADS)

Druken, Kelsey; Stegman, Dave; Kincaid, Christopher; Griffiths, Ross

2013-04-01

"Hotspot" volcanism is generally attributed to upwelling of anomalously warm mantle plumes, the intra-plate Hawaiian island chain and its simple age progression serving as an archetypal example. However, interactions of such plumes with plate margins, and in particular with subduction zones, is likely to have been a common occurrence and leads to more complicated geological records. Here we present results from a series of complementary, three-dimensional numerical and laboratory experiments that examine the dynamic interaction between negatively buoyant subducting slabs and positively buoyant mantle plumes. Slab-driven flow is shown to significantly influence the evolution and morphology of nearby plumes, which leads to a range of deformation regimes of the plume head and conduit. The success or failure of an ascending plume head to reach the lithosphere depends on the combination of plume buoyancy and position within the subduction system, where the mantle flow owing to downdip and rollback components of slab motion entrain plume material both vertically and laterally. Plumes rising within the sub-slab region tend to be suppressed by the surrounding flow field, while wedge-side plumes experience a slight enhancement before ultimately being entrained by subduction. Hotspot motion is more complex than that expected at intraplate settings and is primarily controlled by position alone. Regimes include severely deflected conduits as well as retrograde (corkscrew) motion from rollback-driven flow, often with weak and variable age-progression. The interaction styles and surface manifestations of plumes can be predicted from these models, and the results have important implications for potential hotspot evolution near convergent margins.

Adaptive Control Responses to Behavioral Perturbation Based Upon the Insect

DTIC Science & Technology

2006-11-01

the legs. Visual Sensors Antennal Mechanosensors Antennal Chemosensors Descending Interneurons Controlling Yaw...animals, the antenna were moved back and forth several times with servo motors to identify units that respond to antennal movement in either direction or...role of antennal postures and movements in plume tracking behavior. To date, results have shown that male moths tracking plumes in different wind

Dynamics of Mantle Plume Controlled by both Post-spinel and Post-garnet Phase Transitions

NASA Astrophysics Data System (ADS)

Liu, H.; Leng, W.

2017-12-01

Mineralogical studies indicate that two major phase transitions occur near 660 km depth in the Earth's pyrolitic mantle: the ringwoodite (Rw) to perovskite (Pv) + magnesiowüstite (Mw) and majorite (Mj) to perovskite (Pv) phase transitions. Seismological results also show a complicated phase boundary structure for plume regions at this depth, including broad pulse, double reflections and depressed 660 km discontinuity beneath hot regions etc… These observations have been attributed to the co-existence of these two phase transformations. However, previous geodynamical modeling mainly focused on the effects of Rw-Pv+Mw phase transition on the plume dynamics and largely neglected the effects of Mj-Pv phase transition. Here we develop a 3-D regional spherical geodynamic model to study the influence of the combination of Rw - Pv+Mw and Mj - Pv phase transitions on plume dynamics, including the topography fluctuation of 660 km discontinuity, plume shape and penetration capability of plume. Our results show that (1) a double phase boundary occurs at the hot center area of plume while for other regions with relatively lower temperature the phase boundary is single and flat, which respectively corresponds to the double reflections in the seismic observations and a high velocity prism-like structure at the top of 660 km discontinuity; (2) a large amount of low temperature plume materials could be trapped to form a complex trapezoid overlying the 660 km depth; (3) Mj - Pv phase change strongly enhances the plume penetration capability at 660 km depth, which significantly increases the plume mass flux due to the increased plume radius, but significantly reduces plume heat flux due to the decreased plume temperature in the upper mantle. Our model results provide new enlightenments for better constraining seismic structure and mineral reactions at 660 km phase boundaries.

Comparison of Orbiter PRCS Plume Flow Fields Using CFD and Modified Source Flow Codes

NASA Technical Reports Server (NTRS)

Rochelle, Wm. C.; Kinsey, Robin E.; Reid, Ethan A.; Stuart, Phillip C.; Lumpkin, Forrest E.

1997-01-01

The Space Shuttle Orbiter will use Reaction Control System (RCS) jets for docking with the planned International Space Station (ISS). During approach and backout maneuvers, plumes from these jets could cause high pressure, heating, and thermal loads on ISS components. The object of this paper is to present comparisons of RCS plume flow fields used to calculate these ISS environments. Because of the complexities of 3-D plumes with variable scarf-angle and multi-jet combinations, NASA/JSC developed a plume flow-field methodology for all of these Orbiter jets. The RCS Plume Model (RPM), which includes effects of scarfed nozzles and dual jets, was developed as a modified source-flow engineering tool to rapidly generate plume properties and impingement environments on ISS components. This paper presents flow-field properties from four PRCS jets: F3U low scarf-angle single jet, F3F high scarf-angle single jet, DTU zero scarf-angle dual jet, and F1F/F2F high scarf-angle dual jet. The RPM results compared well with plume flow fields using four CFD programs: General Aerodynamic Simulation Program (GASP), Cartesian (CART), Unified Solution Algorithm (USA), and Reacting and Multi-phase Program (RAMP). Good comparisons of predicted pressures are shown with STS 64 Shuttle Plume Impingement Flight Experiment (SPIFEX) data.

Observations of Inner Shelf Flows Influenced by a Small-Scale River Plume in the Northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Roth, M.; MacMahan, J.; Reniers, A.; Ozgokmen, T. M.

2016-02-01

Recent work has demonstrated that wind and waves are important forcing mechanisms for the inner shelf vertical current structure. Here, the inner shelf flows are evaluated away from an adjacent inlet where a small-scale buoyant plume emerges. The plume's nearshore extent, speed, vertical thickness, and density are controlled by the passage of low-pressure extratropical cyclones that are common in the northern Gulf of Mexico. The colder, brackish plume water provides vertical stratification and a cross-shore density gradient with the warmer, saline oceanic water. An Acoustic Doppler Current Profiler (ADCP) was deployed in 10m water depth as part of an intensive 2-week experiment (SCOPE), which also obtained wind and cross-shelf temperature, salinity, and velocity. The 10m ADCP remained collecting an additional year of velocity observations. The plume was not always present, but episodically influenced the experiment site. When the plume reached the site, the alongshore surface and subsurface typically flowed in opposite directions, likely caused by plume-induced pressure gradients. Plumes that extended into the subsurface appear to have caused depth-averaged onshore flow above that expected from wind and wave-driven forcing. Observations from SCOPE and the 1-year ADCP are used to describe seasonal full-depth flow patterns influenced by wind, waves, and plume presence.

Evolution of Hydrocarbon-Degrading Microbial Communities in the Aftermath of the Deepwater Horizon Oil Well Blowout in the Gulf of Mexico

NASA Astrophysics Data System (ADS)

Andersen, G.; Dubinsky, E. A.; Chakraborty, R.; Hollibaugh, J. T.; Hazen, T. C.

2012-12-01

The Deepwater Horizon oil spill created large plumes of dispersed oil and gas that remained deep in the water column and stimulated growth of several deep-sea bacteria that can degrade hydrocarbons at cold temperatures. We tracked microbial community composition before, during and after the 83-day spill to determine relationships between microbial dynamics, and hydrocarbon and dissolved-oxygen concentrations. Dominant bacteria in plumes shifted drastically over time and were dependent on the concentration of hydrocarbons, and the relative quantities of insoluble and soluble oil fractions. Unmitigated flow from the wellhead early in the spill resulted in the highest concentrations of oil and relatively more n-alkanes suspended in the plume as small oil droplets. These conditions resulted in near complete dominance by alkane-degrading Oceanospirillales, Pseudomonas and Shewanella. Six-weeks into the spill overall hydrocarbon concentrations in the plume decreased and were almost entirely composed of BTEX after management actions reduced emissions into the water column. These conditions corresponded with the emergence of Colwellia, Pseudoalteromonas, Cycloclasticus and Halomonas that are capable of degrading aromatic compounds. After the well was contained dominant plume bacteria disappeared within two weeks after the spill and transitioned to an entirely different set of bacteria dominated by Flavobacteria, Methylophaga, Alteromonas and Rhodobacteraceae that were found in anomalous oxygen depressions throughout August and are prominent degraders of both high molecular weight organic matter as well as hydrocarbons. Bio-Sep beads amended with volatile hydrocarbons from MC-252 oil were used from August through September to create hydrocarbon-amended traps for attracting oil-degrading microbes in situ. Traps were placed at multiple depths on a drilling rig about 600-m from the original MC-252 oil spill site. Microbes were isolated on media using MC-252 oil as the sole carbon source and characterized. Pure cultures were obtained from bacteria similar to those found to dominate hydrocarbon plumes and anomalous oxygen depressions by molecular community analysis. Respirometry studies confirmed that the isolates were able to metabolize the MC-252 oil. Our results from both molecular and culture analysis indicate that indigenous psychrophilic consortia of microorganisms thriving at 5°C from the oil-plume depth water were able to rapidly respond to dispersed oil at depth. The microbial community was highly dynamic and structured by changes in hydrocarbon composition over time. The spill caused sustained alterations in subsurface microbial communities and impacted the deep ocean for at least months after well containment.

Pine Island Glacier, Antarctica, MISR Multi-angle Composite

Atmospheric Science Data Center

2013-12-17

...     View Larger Image (JPEG) A large iceberg has finally separated from the calving front ... next due to stereo parallax. This parallax is used in MISR processing to retrieve cloud heights over snow and ice. Additionally, a plume ...

Aerodynamic and Aeroacoustic Wind Tunnel Testing of the Orion Spacecraft

NASA Technical Reports Server (NTRS)

Ross, James C.

2011-01-01

The Orion aerodynamic testing team has completed more than 40 tests as part of developing the aerodynamic and loads databases for the vehicle. These databases are key to achieving good mechanical design for the vehicle and to ensure controllable flight during all potential atmospheric phases of a mission, including launch aborts. A wide variety of wind tunnels have been used by the team to document not only the aerodynamics but the aeroacoustic environment that the Orion might experience both during nominal ascents and launch aborts. During potential abort scenarios the effects of the various rocket motor plumes on the vehicle must be accurately understood. The Abort Motor (AM) is a high-thrust, short duration motor that rapidly separates Orion from its launch vehicle. The Attitude Control Motor (ACM), located in the nose of the Orion Launch Abort Vehicle, is used for control during a potential abort. The 8 plumes from the ACM interact in a nonlinear manner with the four AM plumes which required a carefully controlled test to define the interactions and their effect on the control authority provided by the ACM. Techniques for measuring dynamic stability and for simulating rocket plume aerodynamics and acoustics were improved or developed in the course of building the aerodynamic and loads databases for Orion.

The Fine Geochemical Structure of the Hawaiian Mantle Plume: Relation to the Earth's Lowermost Mantle

NASA Astrophysics Data System (ADS)

Weis, D.; Harrison, L.

2017-12-01

The Hawaiian mantle plume has been active for >80 Ma with the highest magmatic flux, also distinctly increasing with time. The identification of two clear geochemical trends (Loa-Kea) among Hawaiian volcanoes in all isotope systems has implications for the dynamics and internal structure of the plume conduit and source in the deep mantle. A compilation of modern isotopic data on Hawaiian shield volcanoes and from the Northwest Hawaiian Ridge (NWHR), focusing specifically on high-precision Pb isotopes integrated with Sr, Nd and Hf isotopes, indicates the presence of source differences for Loa- and Kea-trend volcanoes that are maintained throughout the 1 Ma activity of each volcano. These differences extend back in time on all the Hawaiian Islands ( 5 Ma), and as far back as 47 Ma on the NWHR. In all isotope systems, the Loa-trend basalts are more heterogeneous by a factor of 1.5 than the Kea-trend basalts. The Hawaiian mantle plume overlies the boundary between ambient Pacific lower mantle on the Kea side and the Pacific LLSVP on the Loa side. Geochemical differences between Kea and Loa trends reflect preferential sampling of these two distinct sources of deep mantle material, with additional contribution of ULVZ material sporadically on the Loa side. Plume movement up the gently sloping edge of the LLSVP resulted in entrainment of greater amounts of LLSVP-enriched material over time, and explains why the Hawaiian mantle plume dramatically strengthens over time, contrary to plume models. Similar indications of preferential sampling at the edges of the African LLSVP are found in Kerguelen and Tristan da Cunha basalts in the Indian and Atlantic oceans, respectively. The anomalous low-velocity zones at the core-mantle boundary store geochemical heterogeneities that are enriched in recycled material (EM-I type) with different compositions under the Pacific and under Africa, and that are sampled by strong mantle plumes such as Hawaii and Kerguelen.

Control of the plume induced during high-power fiber laser welding with a transverse arc

NASA Astrophysics Data System (ADS)

Wu, Shikai; Zou, Jianglin; Xiao, Rongshi; Li, Fei

2015-04-01

In this letter, the addition of the transverse arc into high-power fiber welding is proposed. The effects of the transverse arc on the laser-induced plume, the morphology of the weld, and the stability of the welding process are investigated. The experimental results indicate that, by introducing the transverse arc, the slender plume disappears, the temperature of the plasma plume increases then decreases with the rise in height, the weld width is reduced by around 42%, and the weld depth and the melting area are enhanced by about 28 and 12%, respectively. Moreover, the stability of the welding process is improved remarkably. As concluded from further analysis, the Mie scattering of the incident laser, induced by the particles in the plume, is responsible for the adverse effects induced by the plume. With the addition of the transverse arc, the particles in the plume are gasified and, thus, do not impact the energy transmission of the fiber laser. Consequently, the adverse effects induced by the plume can be significantly suppressed while the laser energy utilization efficiency and the stability of the welding process are improved.

Geodynamics Of The Yellowstone Hotspot From S Eismic And Gps Imaging: Progress Report

NASA Astrophysics Data System (ADS)

Smith, R. B.; Humphreys, E.; Dueker, K.; Tackley, P.; Waite, G.; Schutt, D.; Hernland, J.

An integrated study of the Yellowstone hotspot and it's interaction with the continental lithosphere is focused on understanding the evolution and effects of plume interaction with the continental lithosphere. Our basic goal is to develop a unified dynamic model of the Yellowstone hotspot and to resolve the question of whether there it has a deep mantle plume source. The 800-km-track of the 16Myr. Yellowstone-Snake River Plain (YSRP) volcanic system extends NE across the western U.S. with associated active seismicity and faulting. We will discuss the initial results of seismic tomography experiments: 1) an 80-instrument, NW-SE trending 500 km x 400 km broadband and high frequency array centered over Yellowstone planned to resolve structural geometry and composition of a presumed mantle plume and to record presumed plume-penetrating rays to ~600 km depth; and 2) an array of ~350 seismic stations of regional seismic networks focusing on the magmatically modified crust using local earthquake and controlled sources. Crustal deformation was assessed by 160-station campaign GPS surveys (1987-2000) complimented by a 15-station permanent GPS network planned to resolve the velocity vectors around the hotspot needed for kinematic and dynamic modeling. Initial tomographic results reveal a low-velocity, upper-crustal body beneath Yellowstone, interpreted to be the source of its active silicic volcanism; conversely, a high-velocity mid crustal body extends along the cooled hotspot track is interpreted to an Fe-rich residuum of the rhyolitic-basaltic volcanism. Teleseismic images within the Yellowstone swell that, combined with isostatic considerations, suggests that convective overturn has left partially molten mantle beneath the hotspot track to depths of about 180 km, and depleted residuum beneath the swell adjacent to the hotspot track. Also the fast axis of mantle anisotropy is oriented in the direction of plate transport; this differs from the anisotropy away from the swell. We can account for the current observations with either a plume or a non -plume source. Initial GPS determinations suggest NE-SW extension of ~2 mm/yr of the across the SRP that is notably slower than the 4-5 mm/yr of NE extension across Yellowstone. Possible mechanisms for the aseismic extension of the SRP include dike intrusion or elastic deformation of a homogeneous, high -strength block. Initial 3D finite element models of GPS and L. Quat. fault slip data reveal s clockwise opening of the YSRP that rotates to general EW extension south of the hotspot track. On a larger scale, 3D numerical simulations of thermal, compositional, and melt buoyancy -driven small-scale (ca. 100 km) convection beneaththe western U.S. indicates a tendency for melting to form lineations aligned with the plate (and extension) direction, although these lineations do not display straightforward hotspot-like propagation. One speculative augment for systematic volcanic propagation of the YSRP and observed seismic images and deformation fields is the interaction between an actively melting asthenosphere, the depleted residuum that it creates, and the upper mantle plate shear that "drags" the depleted residuum downstream of an active melt event for propagating melt instabilities.

Appearance and water quality of turbidity plumes produced by dredging in Tampa Bay, Florida

USGS Publications Warehouse

Goodwin, Carl R.; Michaelis, D.M.

1984-01-01

Turbidity plumes in Tampa Bay, Florida, produced during ship-channel dredging operations from February 1977 to August 1978, were monitored in order to document plume appearance and water quality, evaluate plume influence on the characteristics of Tampa Bay water, and provide a data base for comparison with other areas that have similar sediment, dredge, placement, containment, and tide conditions. The plumes investigated originated from the operation of one hopper dredge and three cutterhead-pipeline dredges. Composition of bottom sediment was found to vary from 85 percent sand and shell fragments to 60 percent silt and clay. Placement methods for dredged sediment included beach nourishment, stationary submerged discharge, oscillating surface discharge, and construction of emergent dikes. Tidal currents ranged from slack water to flow velocities of 0.60 meter per second. Plumes were monitored simultaneously by (1) oblique and vertical 35-millimeter aerial photography and (2) water-quality sampling to determine water clarity and concentrations of nutrients, metals, pesticides, and industrial compounds. Forty-nine photographs depict plumes ranging in length from a few tens of meters to several kilometers and ranging in turbidity level from <10 to 200,000 nephelometric turbidity units. The most visible turbidity plumes were produced by surface discharge of material with high sand content into unconfined placement areas during times of strong tidal currents. The least visible turbidity plumes were produced by discharge of material with high silt and clay content into areas enclosed by floating turbidity barriers during times of weak tidal currents. Beach nourishment from hopper-dredge unloading operations also produced plumes of low visibility. Primary turbidity plumes were produced directly by dredging and placement operations; secondary plumes were produced indirectly by resuspension of previously deposited material. Secondary plumes were formed both by erosion, in areas of high-velocity tidal currents, and by turbulence from vessels passing over fine material deposited in shallow areas. Where turbidity barriers were not used, turbidity plumes visible at the surface were good indicators of the location of turbid water at depth. Where turbidity barriers were used, turbid bottom water was found at locations having no visible surface plumes. A region of rapidly accelerating then decelerating flow near the mouth of Tampa Bay produced a two-part or separated plume. Flow acceleration contracted the width of the visible plume, and subsequent flow deceleration caused plume expansion. The two wide segments of the plume appeared to be separated from each other because of the intervening narrow part. Waters ambient to the plumes were tested for clarity in two sections of Tampa Bay. Ambient-water transparency in Tampa Bay was about three times greater near its mouth, in South Tampa Bay, than near its head, in Hillsborough Bay. Two other measures of water clarity, turbidity and suspended solids, showed no statistically significant difference between the two areas, however, indicating that transparency is a more sensitive measure of ambient water clarity than either turbidity or suspended solids. The nutrient and metal concentrations for samples of plume water and water ambient to the plumes in Tampa Bay were statistically equivalent, indicating no detectable changes due to dredging. The concentrations of dissolved copper, lead, mercury, and total mercury, however, were greater in plumes in Hillsborough Bay than in South Tampa Bay. In Hillsborough Bay, six occurrences of the herbicide 2,4-D at concentrations near the detection limit, 0.01 to 0.05 micrograms per liter, were unrelated to dredging activity. Data recorded for longer than the study period indicate that from 1976 through 1979 few average turbidity characteristics in South Tampa and Hillsborough Bays can be directly attributed to dredging operation

Near-vent chemical processes in a hydrothermal plume: Insights from an integrated study of the Endeavour segment

NASA Astrophysics Data System (ADS)

Coogan, L. A.; Attar, A.; Mihaly, S. F.; Jeffries, M.; Pope, M.

2017-04-01

The Endeavour segment of the Juan de Fuca mid-ocean ridge is one of the best studied ridge segments and has recently been instrumented as part of Ocean Networks Canada's NEPTUNE cabled observatory. Here we investigate the interaction between high-temperature vent fluids and the overlying water column. A new tow-yo survey found that the average temperature anomaly in the neutrally buoyant plume was ˜0.043°C. The water column temperature and light attenuation anomalies correlate linearly in some areas of the plume but in other areas there is a low light attenuation anomaly relative to the temperature anomaly. This temperature excess is interpreted to reflect heat input through (particle-poor) diffuse flow. If this is correct, about half of the heat flux along the Endeavour segment comes from diffuse flow. Sediment trap and push core data show that the mass accumulation rate of the hydrothermal component of the sediments decreases rapidly with distance from the major vent fields. Large changes in the composition of the hydrothermal component of the sediments also occur with distance from the vent fields. The composition of the sediments indicates (i) sulfides precipitate early and accumulate most rapidly close to the vents with a preferential order of element removal from the plume of Cd > Ag > Cu > Co ˜ Fe; (ii) barite is deposited somewhat further from the vents. Strontium and Pb appear to be strongly incorporated in barite and/or other sulfate minerals; (iii) at most a few percent of the mass of these "insoluble" elements that is vented gets deposited within 1.5 km of the vents.

Salt shell fallout during the ash eruption at the Nakadake crater, Aso volcano, Japan: evidence of an underground hydrothermal system surrounding the erupting vent

NASA Astrophysics Data System (ADS)

Shinohara, Hiroshi; Geshi, Nobuo; Yokoo, Akihiko; Ohkura, Takahiro; Terada, Akihiko

2018-03-01

A hot and acid crater lake is located in the Nakadake crater, Aso volcano, Japan. The volume of water in the lake decreases with increasing activity, drying out prior to the magmatic eruptions. Salt-rich materials of various shapes were observed, falling from the volcanic plume during the active periods. In May 2011, salt flakes fell from the gas plume emitted from an intense fumarole when the acid crater lake was almost dry. The chemical composition of these salt flakes was similar to those of the salts formed by the drying of the crater lake waters, suggesting that they originated from the crater lake water. The salt flakes are likely formed by the drying up of the crater lake water droplets sprayed into the plume by the fumarolic gas jet. In late 2014, the crater lake dried completely, followed by the magmatic eruptions with continuous ash eruptions and intermittent Strombolian explosions. Spherical hollow salt shells were observed on several occasions during and shortly after the weak ash eruptions. The chemical composition of the salt shells was similar to the salts formed by the drying of the crater lake water. The hollow structure of the shells suggests that they were formed by the heating of hydrothermal solution droplets suspended by a mixed stream of gas and ash in the plume. The salt shells suggest the existence of a hydrothermal system beneath the crater floor, even during the course of magmatic eruptions. Instability of the magmatic-hydrothermal interface can cause phreatomagmatic explosions, which often occur at the end of the eruptive phase of this volcano.

Assessment of analytical and experimental techniques utilized in conducting plume technology tests 575 and 593. [exhaust flow simulation (wind tunnel tests) of scale model Space Shuttle Orbiter

NASA Technical Reports Server (NTRS)

Baker, L. R.; Sulyma, P. R.; Tevepaugh, J. A.; Penny, M. M.

1976-01-01

Since exhaust plumes affect vehicle base environment (pressure and heat loads) and the orbiter vehicle aerodynamic control surface effectiveness, an intensive program involving detailed analytical and experimental investigations of the exhaust plume/vehicle interaction was undertaken as a pertinent part of the overall space shuttle development program. The program, called the Plume Technology program, has as its objective the determination of the criteria for simulating rocket engine (in particular, space shuttle propulsion system) plume-induced aerodynamic effects in a wind tunnel environment. The comprehensive experimental program was conducted using test facilities at NASA's Marshall Space Flight Center and Ames Research Center. A post-test examination of some of the experimental results obtained from NASA-MSFC's 14 x 14-inch trisonic wind tunnel is presented. A description is given of the test facility, simulant gas supply system, nozzle hardware, test procedure and test matrix. Analysis of exhaust plume flow fields and comparison of analytical and experimental exhaust plume data are presented.

Rocket Plume Scaling for Orion Wind Tunnel Testing

NASA Technical Reports Server (NTRS)

Brauckmann, Gregory J.; Greathouse, James S.; White, Molly E.

2011-01-01

A wind tunnel test program was undertaken to assess the jet interaction effects caused by the various solid rocket motors used on the Orion Launch Abort Vehicle (LAV). These interactions of the external flowfield and the various rocket plumes can cause localized aerodynamic disturbances yielding significant and highly non-linear control amplifications and attenuations. This paper discusses the scaling methodologies used to model the flight plumes in the wind tunnel using cold air as the simulant gas. Comparisons of predicted flight, predicted wind tunnel, and measured wind tunnel forces-and-moments and plume flowfields are made to assess the effectiveness of the selected scaling methodologies.

An Overview of Plume Tracker: Mapping Volcanic Emissions with Interactive Radiative Transfer Modeling

NASA Astrophysics Data System (ADS)

Realmuto, V. J.; Berk, A.; Guiang, C.

2014-12-01

Infrared remote sensing is a vital tool for the study of volcanic plumes, and radiative transfer (RT) modeling is required to derive quantitative estimation of the sulfur dioxide (SO2), sulfate aerosol (SO4), and silicate ash (pulverized rock) content of these plumes. In the thermal infrared, we must account for the temperature, emissivity, and elevation of the surface beneath the plume, plume altitude and thickness, and local atmospheric temperature and humidity. Our knowledge of these parameters is never perfect, and interactive mapping allows us to evaluate the impact of these uncertainties on our estimates of plume composition. To enable interactive mapping, the Jet Propulsion Laboratory is collaborating with Spectral Sciences, Inc., (SSI) to develop the Plume Tracker toolkit. This project is funded by a NASA AIST Program Grant (AIST-11-0053) to SSI. Plume Tracker integrates (1) retrieval procedures for surface temperature and emissivity, SO2, NH3, or CH4 column abundance, and scaling factors for H2O vapor and O3 profiles, (2) a RT modeling engine based on MODTRAN, and (3) interactive visualization and analysis utilities under a single graphics user interface. The principal obstacle to interactive mapping is the computational overhead of the RT modeling engine. Under AIST-11-0053 we have achieved a 300-fold increase in the performance of the retrieval procedures through the use of indexed caches of model spectra, optimization of the minimization procedures, and scaling of the effects of surface temperature and emissivity on model radiance spectra. In the final year of AIST-11-0053 we will implement parallel processing to exploit multi-core CPUs and cluster computing, and optimize the RT engine to eliminate redundant calculations when iterating over a range of gas concentrations. These enhancements will result in an additional 8 - 12X increase in performance. In addition to the improvements in performance, we have improved the accuracy of the Plume Tracker retrievals through refinements in the description of surface emissivity and use of vector projection to define the misfit between model and observed spectra. Portions of this research were conducted at the Jet Propulsion Laboratory, California Institute of Technology, under contract to the National Aeronautics and Space Administration.

Numerical simulations and parameterizations of volcanic plumes observed at Reunion Island

NASA Astrophysics Data System (ADS)

Gurwinder Sivia, Sandra; Gheusi, Francois; Mari, Celine; DiMuro, Andrea; Tulet, Pierre

2013-04-01

Volcanoes are natural composite hazards. The volcanic ejecta can have considerable impact on human health. Volcanic gases and ash, can be especially harmful to people with lung disease such as asthma. Volcanic gases that pose the greatest potential hazards are sulfur dioxide, carbon dioxide, and hydrogen fluoride. Locally, sulfur dioxide gas can lead to acid rain and air pollution downwind from a volcano. These gases can come from lava flows as well as volcano eruptive plumes. This acidic pollution can be transported by wind over large distances. To comply with regulatory rules, modeling tools are needed to accurately predict the contribution of volcanic emissions to air quality degradation. Unfortunately, the ability of existing models to simulate volcanic plume production and dispersion is currently limited by inaccurate volcanic emissions and uncertainties in plume-rise estimates. The present work is dedicated to the study of deep injections of volcanic emissions into the troposphere developed as consequence of intense but localized input of heat near eruptive mouths. This work covers three aspects. First a precise quantification of heat sources in terms of surface, geometry and heat source intensity is done for the Piton de la Fournaise volcano. Second, large eddy simulation (LES) are performed with the Meso-NH model to determine the dynamics and vertical development of volcanic plumes. The estimated energy fluxes and the geometry of the heat source is used at the bottom boundary to generate and sustain the plume, while, passive tracers are used to represent volcanic gases and their injection into the atmosphere. The realism of the simulated plumes is validated on the basis of plume observations. The LES simulations finally serve as references for the development of column parameterizations for the coarser resolution version of the model which is the third aspect of the present work. At spatial resolution coarser than ~1km, buoyant volcanic plumes are sub-grid processes. A new parameterization for the injection height is presented which is based on a modified version of the eddy-diffusivity/mass-flux scheme initially developed for the simulation of convective boundary layer.

Primordial domains in the depleted upper mantle identified by noble gases in MORBs

NASA Astrophysics Data System (ADS)

Tucker, J.; Mukhopadhyay, S.; Langmuir, C. H.; Hamelin, C.; Fuentes, J.

2017-12-01

The distribution of noble gas isotopic compositions in the mantle provides important constraints on the large-scale mantle evolution, as noble gases can trace the interaction between degassed, or processed, mantle domains and undegassed, or primitive, mantle domains. Data from the radiogenic He, Ne, Ar and Xe isotopic systems have shown that plume-related lavas sample relatively undegassed mantle domains, and the recent identification of isotopic anomalies in the short-lived I-Xe and Hf-W isotopic systems in plume-related lavas further suggests that these domains may be ancient, dating back to Earth's accretion. However, little is known about the potential variability of the heavy noble gas systems and the distribution of undegassed domains in the ambient upper mantle not influenced by plumes. Here, we present new high-precision He, Ne, Ar, and Xe isotopic data for a series of MORBs from a depleted section of the subtropical north Mid-Atlantic Ridge, distant from any known plume influence. Some samples have extremely low (unradiogenic) 4He/3He, 21Ne/22Ne, 40Ar/36Ar, and 129Xe/130Xe ratios, including some of the lowest values ever determined for MORBs. Such unradiogenic compositions are reminiscent of OIBs and plume-influenced E-MORBs, suggesting the presence of a relatively undegassed or primitive reservoir in the source of these depleted MORBs. The He, Ne, and Ar isotopic systems are sensitive to the long-term degassing history, suggesting that this domain in the MORB source is ancient. The 129Xe/130Xe ratio is sensitive to degassing only during the first 100 Ma of Earth history, suggesting that some of the isotopic character of these samples has been preserved since Earth's accretion. Together, these observations suggest that primordial or undegassed material is not only sampled in plumes-related lavas, but also normal, depleted MORBs. Along with data from E-MORBs in the southern EPR (Kurz et al., 2005), southern MAR (Sarda et al., 2000), and equatorial MAR (Tucker et al., 2012), our new data suggest that primordial material may be present throughout the MORB source. Such material could either have been stored for a long term in the upper mantle, or recently mixed into the upper mantle from a deeper reservoir.

Diffuse Volcanism at the Young End of the Walvis Ridge - Tristan - Gough Seamount Province: Geochemical Sampling and Constraints on Plume Dynamics

NASA Astrophysics Data System (ADS)

Class, C.; Koppers, A. A. P.; Sager, W. W.; Schnur, S.

2014-12-01

The Walvis Ridge-Tristan/Gough seamount province in the South Atlantic represents 130 Myr of continuous intra-plate volcanism that can be connected to the once conjunct Parana-Etendeka flood basalt province. With this it represents one of the few primary hotspots consistent with the thermal plume model. However, around 60 Ma, the morphological expression of the Walvis Ridge changed drastically from a robust 200 km wide aseismic ridge into a 400 km wide region of diffuse and diminished volcanism. As a result, this part of the plume trail has been described by two subtracks, one ending at Tristan da Cunha and another at Gough Island more than 400 km to the SSE. Where the Walvis Ridge forks into these two tracks there is a center prong. There is also the 39.5°S lineament of seamounts between, but oblique to, the two subtracks, which is parallel to the local fracture zone directions. All these features are at odds with the classical definition of a narrow hotspot track although Rohde et al. (2013) showed that the Tristan and Gough subtracks retain a distinct geochemical signature over 70 Myr and are consistent with a zoned, deep-seated plume. The first Sr-Nd-Hf-Pb isotopic and trace element analyses from the detailed dredge sampling cruise MV1203 show that samples from two prominent seamounts at the western end of the 39.5°S lineament have a Gough-type signature, which makes an upper mantle source for this lineament unlikely but rather indicates that the Gough-type source stretches some 200 km NNW from Gough. Tristan track seamount samples are comparable with published data, however, one new sample has a Gough-type composition suggesting leakage of this component into the Tristan-type plume zone. Seamounts on the middle prong of the Walvis Ridge fork have compositions intermediate to Gough and Tristan domains, suggesting mixing between sources or melts of the two domains. Thus, the Gough-component in the last 60 Myr of plume activity is volumetrically much more significant than previously apparent in only a small number of seamounts with this signature. A spread over much of the width of the seamount province is indicated including some leakage into the Tristan track.

Historical problem areas lessons learned

NASA Technical Reports Server (NTRS)

Sackheim, Bob; Fester, Dale A.

1991-01-01

Historical problem areas in space transportation propulsion technology are identified in viewgraph form. Problem areas discussed include materials compatibility, contamination, pneumatic/feed system flow instabilities, instabilities in rocket engine combustion and fuel sloshing, exhaust plume interference, composite rocket nozzle failure, and freeze/thaw damage.

Saturn Magnetospheric Impact on Surface Molecular Chemistry and Astrobiological Potential of Enceladus

NASA Technical Reports Server (NTRS)

Cooper, Paul D.; Cooper, John F.; Sittler, Edward C.; Burger, Matthew H.; Sturner, Steven J.; Rymer, Abigail M.

2008-01-01

The active south polar surface of Enceladus is exposed to strong chemical processing by direct interaction with charged plasma and energetic particles in the local magnetospheric environment of this icy moon. Chemical oxidation activity is suggested by detection of H202 at the surface in this region and less directly by substantial presence of C02, CO, and N2 in the plume gases. Molecular composition of the uppermost surface, including ejecta from plume activity, is radiolytically transformed mostly by penetrating energetic electrons with lesser effects from more depleted populations of energetic protons. The main sources of molecular plasma ions and E-ring dust grains in the magnetospheric environment are the cryovolcanic plume emissions from Enceladus. These molecular ions and the dust grains are chemically processed by magnetospheric interactions that further impact surface chemistry on return to Enceladus. For example, H20 neutrals dominating the emitted plume gas return to the surface mostly as H30+ ions after magnetospheric processing. Surface oxidant loading is further increased by return of radiolytically processed ice grains from the E-ring. Plume frost deposition and micrometeoroid gardening protect some fraction of newly produced molecular species from destruction by further irradiation. The evident horizontal and vertical mobility of surface ices in the south polar region drive mixing of these processed materials into the moon interior with potential impacts on deep ice molecular chemistry and plume gas production. Similarly as suggested previously for Europa, the externally driven source of radiolytic oxidants could affect evolution of life in any subsurface liquid water environments of Enceladus.

Modeling a three-dimensional river plume over continental shelf using a 3D unstructured grid model

USGS Publications Warehouse

Cheng, R.T.; Casulli, V.; ,

2004-01-01

River derived fresh water discharging into an adjacent continental shelf forms a trapped river plume that propagates in a narrow region along the coast. These river plumes are real and they have been observed in the field. Many previous investigations have reported some aspects of the river plume properties, which are sensitive to stratification, Coriolis acceleration, winds (upwelling or downwelling), coastal currents, and river discharge. Numerical modeling of the dynamics of river plumes is very challenging, because the complete problem involves a wide range of vertical and horizontal scales. Proper simulations of river plume dynamics cannot be achieved without a realistic representation of the flow and salinity structure near the river mouth that controls the initial formation and propagation of the plume in the coastal ocean. In this study, an unstructured grid model was used for simulations of river plume dynamics allowing fine grid resolution in the river and in regions near the coast with a coarse grid in the far field of the river plume in the coastal ocean, in the vertical, fine fixed levels were used near the free surface, and coarse vertical levels were used over the continental shelf. The simulations have demonstrated the uniquely important role played by Coriolis acceleration. Without Coriolis acceleration, no trapped river plume can be formed no matter how favorable the ambient conditions might be. The simulation results show properties of the river plume and the characteristics of flow and salinity within the estuary; they are completely consistent with the physics of estuaries and coastal oceans.

SO2 plume height retrieval from direct fitting of GOME-2 backscattered radiance measurements

NASA Astrophysics Data System (ADS)

van Gent, J.; Spurr, R.; Theys, N.; Lerot, C.; Brenot, H.; Van Roozendael, M.

2012-04-01

The use of satellite measurements for SO2 monitoring has become an important aspect in the support of aviation control. Satellite measurements are sometimes the only information available on SO2 concentrations from volcanic eruption events. The detection of SO2 can furthermore serve as a proxy for the presence of volcanic ash that poses a possible hazard to air traffic. In that respect, knowledge of both the total vertical column amount and the effective altitude of the volcanic SO2 plume is valuable information to air traffic control. The Belgian Institute for Space Aeronomy (BIRA-IASB) hosts the ESA-funded Support to Aviation Control Service (SACS). This system provides Volcanic Ash Advisory Centers (VAACs) worldwide with near real-time SO2 and volcanic ash data, derived from measurements from space. We present results from our algorithm for the simultaneous retrieval of total vertical columns of O3 and SO2 and effective SO2 plume height from GOME-2 backscattered radiance measurements. The algorithm is an extension to the GODFIT direct fitting algorithm, initially developed at BIRA-IASB for the derivation of improved total ozone columns from satellite data. The algorithm uses parameterized vertical SO2 profiles which allow for the derivation of the peak height of the SO2 plume, along with the trace gas total column amounts. To illustrate the applicability of the method, we present three case studies on recent volcanic eruptions: Merapi (2010), Grímsvotn (2011), and Nabro (2011). The derived SO2 plume altitude values are validated with the trajectory model FLEXPART and with aerosol altitude estimations from the CALIOP instrument on-board the NASA A-train CALIPSO platform. We find that the effective plume height can be obtained with a precision as fine as 1 km for moderate and strong volcanic events. Since this is valuable information for air traffic, we aim at incorporating the plume height information in the SACS system.

The Snake River Plain Volcanic Province: Insights from Project Hotspot

NASA Astrophysics Data System (ADS)

Shervais, J. W.; Potter, K. E.; Hanan, B. B.; Jean, M. M.; Duncan, R. A.; Champion, D. E.; Vetter, S.; Glen, J. M. G.; Christiansen, E. H.; Miggins, D. P.; Nielson, D. L.

2017-12-01

The Snake River Plain (SRP) Volcanic Province is the best modern example of a time-transgressive hotspot track beneath continental crust. The SRP began 17 Ma with massive eruptions of Columbia River basalt and rhyolite. After 12 Ma volcanism progressed towards Yellowstone, with early rhyolite overlain by basalts that may exceed 2 km thick. The early rhyolites are anorogenic with dry phenocryst assemblages and eruption temperatures up to 950C. Tholeiitic basalts have major and trace element compositions similar to ocean island basalts (OIB). Project Hotspot cored three deep holes in the central and western Snake River Plain: Kimama (mostly basalt), Kimberly (mostly rhyolite), and Mountain Home (lake sediments and basaslt). The Kimberly core documents rhyolite ash flows up to 700 m thick, possibly filling a caldera or sag. Chemical stratigraphy in Kimama and other basalt cores document fractional crystallization in relatively shallow magma chambers with episodic magma recharge. Age-depth relations in the Kimama core suggest accumulation rates of roughly 305 m/Ma. Surface and subsurface basalt flows show systematic variations in Sr-Nd-Pb isotopes with distance from Yellowstone interpreted to reflect changes in the proportion of plume source and the underlying heterogeneous cratonic lithosphere, which varies in age, composition, and thickness from west to east. Sr-Nd-Pb isotopes suggest <5% lithospheric input into a system dominated by OIB-like plume-derived basalts. A major flare-up of basaltic volcanism occurred 75-780 ka throughout the entire SRP, from Yellowstone in the east to Boise in the west. The youngest western SRP basalts are transitional alkali basalts that range in age from circa 900 ka to 2 ka, with trace element and isotopic compositions similar to the plume component of Hawaiian basalts. These observations suggest that ancient SCLM was replaced by plume mantle after the North America passed over the hotspot in the western SRP, which triggered renewed basaltic volcanism throughout the system. This young volcanism supports an active geothermal system fueled by a shallow crustal sill complex that underlies most of the SRP today.

Sr, Nd, Pb and Hf Isotopic Compositions of Late Cenozoic Alkali Basalts in South Korea: Evidence for Mixing Between the Two Dominant Asthenospheric Mantle Domains beneath East Asia

NASA Astrophysics Data System (ADS)

Choi, S.; Mukasa, S. B.; Kwon, S.; Andronikov, A. V.

2004-12-01

We determined the Sr, Nd, Pb and Hf isotopic compositions of late Cenozoic basaltic rocks from six lava-field provinces in South Korea, including Baengnyeong Island, Jogokni, Ganseong area, Jeju Island, Ulleung Island and Dog Island, in order to understand the nature of the mantle source. The basalts have OIB-like trace element abundance patterns, and also contain mantle-derived xenoliths. Available isotope data of late Cenozoic basalts from East Asia, along with ours, show that the mantle source has a DMM-EM1 array for northeast China and a DMM-EM2 array for Southeast Asia. We note that the basalts falling on an array between DMM and an intermediate end member between EM1 and EM2, are located between the two large-scale isotopic provinces, i.e., around the eastern part of South Korea. The most intriguing observation on the isotopic correlation diagrams is spatial variation from predominantly EM2 signatures in the basaltic lavas toward increasingly important addition of EM1, starting from Jeju Island to Ulleung and Dog Islands to Ganseong area, and to Baengnyeong Island. This is without any corresponding changes in the basement and the lithospheric mantle beneath the region. These observations suggest that the asthenospheric mantle source is dominant for the Cenozoic intraplate volcanism in East Asia, which is characterized by two distinct, large-scale domains. Previous studies on East Asian Cenozoic volcanic rocks have invoked origins by either plume activity or decompressional melting in a rift environment. On the basis of our new trace element and isotopic compositions which have OIB-like characteristics, we prefer a plume origin for these lavas. However, because tomographic images do not show distinct thermal anomaly that would be interpreted as a plume, we suggest that the magmatism might be the product of small, difficult to image multiple plumes that tapped the shallow part of the asthenosphere (probably the transition zone in the upper mantle).

Nitrous oxide as an indicator of nitrogen transformation in a septic system plume

NASA Astrophysics Data System (ADS)

Li, L.; Spoelstra, J.; Robertson, W. D.; Schiff, S. L.; Elgood, R. J.

2014-11-01

This study evaluates the use of ground water N2O concentration and stable isotope composition for providing insights into nitrogen cycling processes in a large septic system plume in southern Ontario, Canada. An extremely large range of dissolved N2O concentrations were measured (0.4-1071 μg N/L) that were higher than atmospheric equilibrium values of ∼0.3 μg N/L, demonstrating substantial N2O production in the subsurface. The highest N2O concentrations occurred around the periphery of a mid-depth zone where NO3- attenuation, elevated DOC concentration, and NO3- stable isotope ratios provided evidence that denitrification was occurring. Broad ranges in δ15N-N2O (-45.8‰ to +30.6‰) and δ18O-N2O (+20.4‰ to +96.0‰) were evident. Using literature isotopic enrichment factors, which differ for N2O produced during nitrification and denitrification, and measured ranges of plume NH4+ and NO3- isotopic ratios, zones of both nitrifier-derived N2O (shallow zone) and denitrifier-N2O (mid-depth and deeper zones) could be identified. Time series sampling showed that nitrifier N2O was present early in the summer season (June) but then denitrifier N2O was more dominant later in the season. In a mid-depth NO3- depleted zone, the production of denitrifier-N2O was evident early in the season when 15N and 18O enrichment of NO3- was not sufficiently advanced to be indicative of denitrification, although δ15N and δ18O values of NO3- increased later in the season. The analysis of N2O concentrations and stable isotopic composition, in conjunction with conventional chemical analyses, provides insights into N-cycling processes in the Long Point ground water septic plume. However, large ranges in the isotopic composition of N2O produced by nitrifiers and denitrifiers meant that δ15N and δ18O analysis of ground water N2O provided qualitative, rather than quantitative, information on denitrifier versus nitrifier production of N2O at this site.

A six degree of freedom, plume-fuel optimal trajectory planner for spacecraft proximity operations using an A* node search. M.S. Thesis - MIT

NASA Technical Reports Server (NTRS)

Jackson, Mark Charles

1994-01-01

Spacecraft proximity operations are complicated by the fact that exhaust plume impingement from the reaction control jets of space vehicles can cause structural damage, contamination of sensitive arrays and instruments, or attitude misalignment during docking. The occurrence and effect of jet plume impingement can be reduced by planning approach trajectories with plume effects considered. An A* node search is used to find plume-fuel optimal trajectories through a discretized six dimensional attitude-translation space. A plume cost function which approximates jet plume isopressure envelopes is presented. The function is then applied to find relative costs for predictable 'trajectory altering' firings and unpredictable 'deadbanding' firings. Trajectory altering firings are calculated by running the spacecraft jet selection algorithm and summing the cost contribution from each jet fired. A 'deadbanding effects' function is defined and integrated to determine the potential for deadbanding impingement along candidate trajectories. Plume costs are weighed against fuel costs in finding the optimal solution. A* convergence speed is improved by solving approach trajectory problems in reverse time. Results are obtained on a high fidelity space shuttle/space station simulation. Trajectory following is accomplished by a six degree of freedom autopilot. Trajectories planned with, and without, plume costs are compared in terms of force applied to the target structure.

10 CFR 50.47 - Emergency plans.

Code of Federal Regulations, 2014 CFR

2014-01-01

... to the populace within the plume exposure pathway Emergency Planning Zone have been established. (6... has been developed for the plume exposure pathway EPZ for emergency workers and the public. In... pathway EPZ appropriate to the locale have been developed. (11) Means for controlling radiological...

10 CFR 50.47 - Emergency plans.

Code of Federal Regulations, 2013 CFR

2013-01-01

... to the populace within the plume exposure pathway Emergency Planning Zone have been established. (6... has been developed for the plume exposure pathway EPZ for emergency workers and the public. In... pathway EPZ appropriate to the locale have been developed. (11) Means for controlling radiological...

10 CFR 50.47 - Emergency plans.

Code of Federal Regulations, 2012 CFR

2012-01-01

... to the populace within the plume exposure pathway Emergency Planning Zone have been established. (6... has been developed for the plume exposure pathway EPZ for emergency workers and the public. In... pathway EPZ appropriate to the locale have been developed. (11) Means for controlling radiological...

Constraints on Thermochemical Convection of the Mantle from Plume-related Observations

NASA Astrophysics Data System (ADS)

Zhong, S.

2005-05-01

Although geochemical observations have long suggested a layered mantle with more enriched mantle material in the bottom layer to provide a significant amount of heat to the top layer, the nature of such a layering remains unclear. An important observation that has been used to argue against the conventional layered mantle model (i.e., the layering at the 670 km depth) was the plume heat flux [Davies, 1999]. Plume heat flux is estimated as ~ 3.5 TW, or 10% of the surface heat flux [Davies, 1988; Sleep, 1990]. In this study, we demonstrate with 3-D spherical models of mantle convection with depth- and temperature-dependent viscosity that observed plume heat flux, plume excess temperature (<350°C), and upper mantle temperature (~ 1300°C) can pose important constraints on the layered mantle convection. We show that for a purely thermal convection model (i.e., a whole mantle convection), the observations of plume heat flux, plume excess temperature, and upper mantle temperature can be simultaneously explained only when internal heating rate is about 65%. For smaller internal heating rate, plume heat flux and plume excess temperature would be too large, and upper mantle temperature would be too small, compared with the observed. This suggests that for a whole mantle convection the CMB heat flux needs to be > 10 TW. For a core with no significant heat producing elements, such large CMB heat flux may lead to too rapid cooling of the core or a too young inner core. A layered mantle convection may help reduce the CMB heat flux. For layered convection models, we found that the top layer needs to be ~70% internally heated to explain the upper mantle temperature and plume-related observations, and this required internal heating ratio is insensitive to the layer thickness for the bottom layer (we used ~600 km and 1100 km thicknesses). This result suggests that heat generation rate for the bottom layer cannot be significantly larger (< a factor of 2) than that for the top layer. thus challenging the conventional geochemical inference for an significantly enriched bottom layer. However, this is more consistent with recent estimate of the MORB source composition that increases heat producing element concentration by a factor of three compared with the previously proposed.

Source mass eruption rate retrieved from satellite-based data using statistical modelling

NASA Astrophysics Data System (ADS)

Gouhier, Mathieu; Guillin, Arnaud; Azzaoui, Nourddine; Eychenne, Julia; Valade, Sébastien

2015-04-01

Ash clouds emitted during volcanic eruptions have long been recognized as a major hazard likely to have dramatic consequences on aircrafts, environment and people. Thus, the International Civil Aviation Organization (ICAO) established nine Volcanic Ash Advisory Centers (VAACs) around the world, whose mission is to forecast the location and concentration of ash clouds over hours to days, using volcanic ash transport and dispersion models (VATDs). Those models use input parameters such as plume height (PH), particle size distribution (PSD), and mass eruption rate (MER), the latter being a key parameter as it directly controls the amount of ash injected into the atmosphere. The MER can be obtained rather accurately from detailed ground deposit studies, but this method does not match the operational requirements in case of a volcanic crisis. Thus, VAACs use empirical laws to determine the MER from the estimation of the plume height. In some cases, this method can be difficult to apply, either because plume height data are not available or because uncertainties related to this method are too large. We propose here an alternative method based on the utilization of satellite data to assess the MER at the source, during explosive eruptions. Satellite-based techniques allow fine ash cloud loading to be quantitatively retrieved far from the source vent. Those measurements can be carried out in a systematic and real-time fashion using geostationary satellite, in particular. We tested here the relationship likely to exist between the amount of fine ash dispersed in the atmosphere and of coarser tephra deposited on the ground. The sum of both contributions yielding an estimate of the MER. For this purpose we examined 19 eruptions (of known duration) in detail for which both (i) the amount of fine ash dispersed in the atmosphere, and (ii) the mass of tephra deposited on the ground have been estimated and published. We combined these data with contextual information that may influence the statistical relationship such as the magma composition or the existence of phreatomagmatism. In order to infer the relationship between ash content in the atmosphere and the amount of tephra on the ground, we used advanced statistic modelling using model selection, with AIC-type (Akaike Information Criterion) penalization, and classification. First we show that a reliable statistical relationship does exist between atmospheric fine ash and tephra fall deposits. Then we show that magma composition does have an effect on this relationship. It follows a power function in the form S_1=c_0{S_2}c_1(P_n))Hc_2 having a coefficient of determination r2=0.91 and a prediction error of 2.16 at a confidence level of 95%. S1 is the mass of tephra fall deposits and S2 is the fine ash cloud mass as retrieved from satellite measurements. H is the plume height, c0 and c2 are constant coefficients while c1 is variable and depends on the magma composition type (Pn=1:3). This method greatly improves the prediction capability of the source MER as compared to the one based on the plume height solely. If available in real-time, satellite data might be advantageously used as a proxy by the VAACs, to derive key source parameters such as the MER.

A subscale facility for liquid rocket propulsion diagnostics at Stennis Space Center

NASA Technical Reports Server (NTRS)

Raines, N. G.; Bircher, F. E.; Chenevert, D. J.

1991-01-01

The Diagnostics Testbed Facility (DTF) at NASA's John C. Stennis Space Center in Mississippi was designed to provide a testbed for the development of rocket engine exhaust plume diagnostics instrumentation. A 1200-lb thrust liquid oxygen/gaseous hydrogen thruster is used as the plume source for experimentation and instrument development. Theoretical comparative studies have been performed with aerothermodynamic codes to ensure that the DTF thruster (DTFT) has been optimized to produce a plume with pressure and temperature conditions as much like the plume of the Space Shuttle Main Engine as possible. Operation of the DTFT is controlled by an icon-driven software program using a series of soft switches. Data acquisition is performed using the same software program. A number of plume diagnostics experiments have utilized the unique capabilities of the DTF.

The influence of material and mesh characteristics on transmission mode desorption electrospray ionization.

PubMed

Chipuk, Joseph E; Brodbelt, Jennifer S

2009-04-01

Adaptation of desorption electrospray ionization to a transmission mode (TM-DESI) entails passing an electrospray plume through a sample that has been deposited onto a mesh substrate. A combination of mass spectrometry and fluorescence microscopy studies is used to illustrate the critical role material composition, mesh open space, and mesh fiber diameter play on the transmission, desorption, and ionization process. Substrates with open spaces less than 150 microm and accompanying minimal strand diameters produce less scattering of the plume and therefore favor transmission. Larger strand diameters typically encompass larger open spaces, but the increase in the surface area of the strand increases plume scattering as well as solvent and analyte spreading on the mesh. Polypropylene (PP), ethylene tetrafluoroethylene (ETFE), and polyetheretherketone (PEEK) materials afford much better desorption than similarly sized polyethylene terephthalate (PETE) or nylon-6,6 (PA66) substrates. Ultimately, the manner in which the electrospray plume interacts with the mesh as it is transmitted through the substrate is shown to be critical to performing and optimizing TM-DESI analyses. In addition, evidence is presented for analyte dependent variations in the desorption mechanisms of dry and solvated samples.

Volatiles and energy released by Puracé volcano

NASA Astrophysics Data System (ADS)

Maldonado, Luisa Fernanda Meza; Inguaggiato, Salvatore; Jaramillo, Marco Tulio; Valencia, Gustavo Garzón; Mazot, Agnes

2017-12-01

Total CO2 output of Puracé volcano (Colombia) was estimated on the basis of fluids discharged by fumaroles, soil gases, and dissolved carbon species in the aquifer. The soil CO2 emission was computed from a field survey of 512 points of CO2 soil flux measurements at the main degassing areas of Puracé volcano. The CO2 flux from Puracé's plume was estimated using an indirect method, that used the SO2 plume flux and CO2/SO2 ratio of the main high temperature fumarole. The total output of CO2 was estimated at ≅ 1500 t/day. The main contribution of CO2 comes from the plume (summit degassing) and from soil degassing that emit 673 and 812 t/day, respectively. The contributions of summit and soil degassing areas are comparable, indicating an intermediate degassing style partitioned between closed and open conduit systems. The estimated water vapor discharge (as derived from the chemical composition of the fumaroles, the H2O/CO2 ratio, and the SO2 plume flux) allowed calculation of the total thermal energy (fumarolic, soil degassing, and aquifer) released from the Puracé volcanic system. This was 360 MW.

Meteorological and Aerosol effects on Marine Cloud Microphysical Properties

NASA Astrophysics Data System (ADS)

Sanchez, K. J.; Russell, L. M.; Modini, R. L.; Frossard, A. A.; Ahlm, L.; Roberts, G.; Hawkins, L. N.; Schroder, J. C.; Wang, Z.; Lee, A.; Abbatt, J.; Lin, J.; Nenes, A.; Wonaschuetz, A.; Sorooshian, A.; Noone, K.; Jonsson, H.; Albrecht, B. A.; Desiree, T. S.; Macdonald, A. M.; Seinfeld, J.; Zhao, R.

2015-12-01

Both meteorology and microphysics affect cloud formation and consequently their droplet distributions and shortwave reflectance. The Eastern Pacific Emitted Aerosol Cloud Experiment (EPEACE) and the Stratocumulus Observations of Los-Angeles Emissions Derived Aerosol-Droplets (SOLEDAD) studies provide detailed measurements in 6 case studies of both cloud thermodynamic properties and initial particle number distribution and composition, as well as the resulting cloud drop distribution and composition. This study uses simulations of a detailed chemical and microphysical aerosol-cloud parcel (ACP) model with explicit kinetic drop activation to reproduce the observed cloud droplet distribution and composition. Four of the cases examined had a sub-adiabatic lapse rate, which was shown to have fewer droplets due to decreased maximum supersaturation, lower LWC and higher cloud base height, consistent with previous findings. These detailed case studies provided measured thermodynamics and microphysics that constrained the simulated droplet size distribution sufficiently to match the droplet number within 6% and the size within 19% for 4 of the 6 cases, demonstrating "closure" or consistency of the measured composition with the measured CCN spectra and the inferred and modeled supersaturation. The contribution of organic components to droplet formation shows small effects on the droplet number and size in the 4 marine cases that had background aerosol conditions with varying amounts of coastal, ship or other non-biogenic sources. In contrast, the organic fraction and hygroscopicity increased the droplet number and size in the cases with generated smoke and cargo ship plumes that were freshly emitted and not yet internally mixed with the background particles. The simulation results show organic hygroscopicity causes small effects on cloud reflectivity (<0.7%) with the exception of the cargo ship plume and smoke plume which increased absolute cloud reflectivity fraction by 0.02 and 0.20 respectively. In addition, the ACP model simulations are compared to those from a numerical parameterization of cloud droplet activation that is suitable for GCMs and show droplet concentrations are comparable between the two methods.

Applications of the 190Pt-186Os isotope system to geochemistry and cosmochemistry

USGS Publications Warehouse

Walker, R.J.; Morgan, J.W.; Beary, E.S.; Smoliar, M.I.; Czamanske, G.K.; Horan, M.F.

1997-01-01

Platinum is fractionated from osmium primarily as a consequence of processes involving sulfide and metal crystallization. Consequently, the 190Pt-186Os isotope system (190Pt ??? 186Os + ??) shows promise for dating some types of magmatic sulfide ores and evolved iron meteorites. The first 190Pt-186Os isochrons are presented here for ores from the ca. 251 Ma Noril'sk, Siberia plume, and for group IIAB magmatic iron meteorites. Given the known age of the Noril'sk system, a decay constant for 190Pt is determined to be 1.542 ?? 10-12a-1, with ??1% uncertainty. The isochron generated for the IIAB irons is consistent with this decay constant and the known age of the group. The 186Os/188Os ratios of presumably young, mantle-derived osmiridiums and also the carbonaceous chondrite Allende were measured to high-precision to constrain the composition of the modern upper mantle. These compositions overlap, indicating that the upper mantle is chondritic within the level of resolution now available. Our best estimate for this 186Os/188Os ratio is 0.119834 ?? 2 (2??M). The 190Pt/186Os ratios determined for six enstatite chondrites average 0.001659 ?? 75, which is very similar to published values for carbonaceous chondrites. Using this ratio and the presumed composition of the modern upper mantle and chondrites, a solar system initial 186Os/188Os ratio of 0.119820 is calculated. In comparison to the modern upper mantle composition, the 186Os/188Os ratio of the Noril'sk plume was approximately 0.012% enriched in 186Os. Possible reasons for this heterogeneity include the recycling of Pt-rich crust into the mantle source of the plume and derivation of the osmium from the outer core. Derivation of the osmium from the outer core is our favored model. Copyright ?? 1997 Elsevier Science Ltd.

Widespread melt/rock interaction and seismic properties of the lithosphere above mantle plumes: A petrological and microstructural study of mantle xenoliths from French Polynesia

NASA Astrophysics Data System (ADS)

Tommasi, A.; Godard, M.

2002-12-01

In addition to thermal erosion, plume/lithosphere interaction may induce significant changes in the lithosphere chemical composition. To constrain the extent of this process in an oceanic environment and its consequences on the lithosphere seismic properties, we studied the relationship between petrological processes and microstructure in mantle xenoliths from the Austral-Cook, Society and Marquesas islands. Olivine forsterite contents in our sp-peridotites vary continuously from Fo91 to Fo83, the lowest Fo being observed in dunites and wehrlites. Yet, their high Ni content (up to 2500 ppm) precludes a cumulate origin. These rocks are rather interpreted as resulting from melt/rock reactions involving olivine precipitation and pyroxene dissolution, the dunites indicating high melt-rock ratios. Moreover, wehrlites display poikiloblastic diopside enclosing corroded olivines. Late crystallization of clinopyroxene, also observed in lherzolites, may result from a near-solidus melt-freezing reaction occurring at the boundary of a partial melting domain developed at the expenses of lithospheric mantle. These data suggest that the lithosphere above a mantle plume undergoes a complex sequence of magmatic processes that significantly change its composition. Yet, crystal preferred orientations and thus seismic anisotropy are little affected by these processes. Lherzolites and harzburgites, independent from composition, show high-temperature porphyroclastic microstructures and strong olivine CPO. Although dunites and wehrlites display annealing microstructures to which is associated a progressive dispersion of the olivine CPO, very weak CPO are limited to a few dunites and wehrlites, suggesting that CPO destruction is restricted to domains of intense magma-rock interaction due to localized flow or accumulation of magmas. Conversely, the compositional changes result in lower seismic velocities for P- and S-waves. Relative to normal mantle, seismic anomalies may attain -2.5 percent and be equivalent to those observed below the Deccan, Parana, or Ontong Java mesozoic LIPs.

Widespread melt/rock interaction and seismic properties of the lithosphere above mantle plumes: Evidence from mantle xenoliths from French Polynesia

NASA Astrophysics Data System (ADS)

Tommasi, A.; Godard, M.; Coromina, G.; Dautria, J. M.; Barczus, H.

2003-04-01

In addition to thermal erosion, plume/lithosphere interaction may induce significant changes in the lithosphere chemical composition. To constrain the extent of this process in an oceanic environment and its consequences on the lithosphere seismic properties, we studied the relationship between petrological processes and microstructure in mantle xenoliths from the Austral-Cook, Society and Marquesas islands. Olivine forsterite contents in our sp-peridotites vary continuously from Fo91 to Fo83, the lowest Fo being observed in dunites and wehrlites. Yet, their high Ni content (up to 2500 ppm) precludes a cumulate origin. These rocks are rather interpreted as resulting from melt/rock reactions involving olivine precipitation and pyroxene dissolution, the dunites indicating high melt-rock ratios. Moreover, wehrlites display poikiloblastic diopside enclosing corroded olivines. Late crystallization of clinopyroxene, also observed in lherzolites, may result from a near-solidus melt-freezing reaction occurring at the boundary of a partial melting domain developed at the expenses of lithospheric mantle. These data suggest that the lithosphere above a mantle plume undergoes a complex sequence of magmatic processes that significantly change its composition. Yet, crystal preferred orientations and thus seismic anisotropy are little affected by these processes. Lherzolites and harzburgites, independent from composition, show high-temperature porphyroclastic microstructures and strong olivine CPO. Although dunites and wehrlites display annealing microstructures to which is associated a progressive dispersion of the olivine CPO, very weak CPO are limited to a few dunites and wehrlites, suggesting that CPO destruction is restricted to domains of intense magma-rock interaction due to localized flow or accumulation of magmas. Conversely, the compositional changes result in lower seismic velocities for P- and S-waves. Relative to normal mantle, seismic anomalies may attain -2.5 (2.2) percent for P (S) waves and be equivalent to those observed below the Deccan, Parana, or Ontong Java mesozoic LIPs.

On the Use of Ocean Color Remote Sensing to Measure the Transport of Dissolved Organic Carbon by the Mississippi River Plume

NASA Technical Reports Server (NTRS)

DelCastillo, Carlos E.; Miller, Richard L.

2007-01-01

We investigated the use of ocean color remote sensing to measure transport of dissolved organic carbon (DOC) by the Mississippi River to the Gulf of Mexico. From 2000 to 2005 we recorded surface measurements of DOC, colored dissolved organic matter (CDOM), salinity, and water-leaving radiances during five cruises to the Mississippi River Plume. These measurements were used to develop empirical relationships to derive CDOM, DOC, and salinity from monthly composites of SeaWiFS imagery collected from 1998 through 2005. We used river flow data and a two-end-member mixing model to derive DOC concentrations in the river end-member, river flow, and DOC transport using remote sensing data. We compared our remote sensing estimates of river flow and DOC transport with data collected by the United States Geological Survey (USGS) from 1998 through 2005. Our remote sensing estimates of river flow and DOC transport correlated well (r2 0.70) with the USGS data. Our remote sensing estimates and USGS field data showed low variability in DOC concentrations in the river end-member (7-11%), and high seasonal variability in river flow (50%). Therefore, changes in river flow control the variability in DOC transport, indicating that the remote sensing estimate of river flow is the most critical element of our DOC transport measurement. We concluded that it is possible to use this method to estimate DOC transport by other large rivers if there are data on the relationship between CDOM, DOC, and salinity in the river plume.

Jupiter’s moon Europa

NASA Image and Video Library

2014-01-24

This composite image shows suspected plumes of water vapor erupting at the 7 o’clock position off the limb of Jupiter’s moon Europa. The plumes, photographed by NASA’s Hubble’s Space Telescope Imaging Spectrograph, were seen in silhouette as the moon passed in front of Jupiter. Hubble’s ultraviolet sensitivity allowed for the features -- rising over 100 miles (160 kilometers) above Europa’s icy surface -- to be discerned. The water is believed to come from a subsurface ocean on Europa. The Hubble data were taken on January 26, 2014. The image of Europa, superimposed on the Hubble data, is assembled from data from the Galileo and Voyager missions.

National environmental observing system to mitigate the effects of nuclear-biological-chemical (NBC) attacks: strategic and tactical

NASA Astrophysics Data System (ADS)

Fleming, Rex J.

2003-09-01

The challenge of obtaining an adequate environmental support system to help mitigate the effects of various terrorist generated plumes is articulated and a fiscally responsible solution is presented. A substantially improved national system of upper air data observing systems serves as a powerful information source prior to a terrorist event. A mobile tactical observing system for measuring the environment and for measuring the composition and intensity of the plume is implemented immediately following an event. Only proven and tested technologies are used. Program costs, benefits for the fight against terrorism, and multiple benefits to other aspects of the economy are summarized.

Isotopic evolution of Mauna Loa Volcano: A view from the submarine southwest rift zone

NASA Astrophysics Data System (ADS)

Kurz, Mark D.; Kenna, T. C.; Kammer, D. P.; Rhodes, J. Michael; Garcia, Michael O.

New isotopic and trace element measurements on lavas from the submarine southwest rift zone (SWR) of Mauna Loa continue the temporal trends of subaerial Mauna Loa flows, extending the known compositional range for this volcano, and suggesting that many of the SWR lavas are older than any exposed on land. He and Nd isotopic compositions are similar to those in the oldest subaerial Mauna Loa lavas (Kahuku and Ninole Basalts), while 87Sr/86Sr ratios are slightly lower (as low as .7036) and Pb isotopes are higher (206Pb'204Pb up to 18.30). The coherence of all the isotopes suggests that helium behaves as an incompatible element, and that helium isotopic variations in the Hawaiian lavas are produced by melting and mantle processes, rather than magma chamber or metasomatic processes unique to the gaseous elements. The variations of He, Sr, and Nd are most pronounced in lavas of approximately 10 ka age range [Kurz and Kammer, 1991], but the largest Pb isotopic variation occurs earlier. These variations are interpreted as resulting from the diminishing contribution from the upwelling mantle plume material as the shield building ends at Mauna Loa. The order of reduction in the plume isotopic signature is inferred to be Pb (at >100 ka), He (at ˜14 ka), Sr (at ˜9 ka), and Nd (at ˜8 ka); the different timing may relate to silicate/melt partition coefficients, with most incompatible elements removed first, and also to concentration variations within the plume. Zr/Nb, Sr/Nb, and fractionation-corrected Nb concentrations, correlate with the isotopes and are significantly higher in some of the submarine SWR lavas, suggesting temporal variability on time scales similar to the Pb isotopes (i.e. ˜ 100 ka). Historical lavas define trace element and isotopic trends that are distinct from the longer term (10 to 100 ka) variations, suggesting that different processes cause the short term variability. The temporal evolution of Mauna Loa, and particularly the new data from the submarine SWR, suggest that the isotopic composition of the upwelling plume mantle is best represented by data from Loihi seamount tholeiites. The temporal evolution suggests that the mantle source of the latest stage of Mauna Loa, which is characterized by radiogenic 87Sr/86Sr (up to .70395), unradiogenic 206Pb/204Pb (˜18.0), 3He/4He ratios similar to MORB, and low Nb concentrations, is a small-volume contribution related to non-plume components (such as normal asthenosphere, or entrained mantle).

Isopycnal deepening of an under-ice river plume in coastal waters: Field observations and modeling

NASA Astrophysics Data System (ADS)

Li, S. Samuel; Ingram, R. Grant

2007-07-01

The Great Whale River, located on the southeast coast of Hudson Bay in Canada, forms a large river plume under complete landfast ice during early spring. Short-term fluctuations of plume depth have motivated the present numerical study of an under-ice river plume subject to tidal motion and friction. We introduce a simple two-layer model for predicting the vertical penetration of the under-ice river plume as it propagates over a deepening topography. The topography is idealized but representative. Friction on the bottom surface of the ice cover, on the seabed, and at the plume interface is parameterized using the quadratic friction law. The extent of the vertical penetration is controlled by dimensionless parameters related to tidal motion and river outflow. Model predictions are shown to compare favorably with under-ice plume measurements from the river mouth. This study illustrates that isopycnal deepening occurs when the ice-cover vertical motion creates a reduced flow cross-section during the ebbing tide. This results in supercritical flow and triggers the downward plume penetration in the offshore. For a given river discharge, the freshwater source over a tidal cycle is unsteady in terms of discharge velocity because of the variation in the effective cross-sectional area at the river mouth, through which freshwater flows.

Optical and chemical properties of wildland biomass burning particles measured downwind during the BBOP study

NASA Astrophysics Data System (ADS)

Onasch, Timothy; Wormhoudt, Jody; Sedlacek, Arthur; Chand, Duli; Freedman, Andrew

2017-04-01

Rapid physical, chemical and optical changes in biomass burning particles were measured downwind (< 3 hours temporally) from wildland fires. The Biomass Burning Observation Project (BBOP), sponsored by the U.S. Department of Energy (DOE), involved the measurement of emissions from wildland fires in the Pacific Northwest and agricultural burns in the Central Southeastern United States observed from the DOE Gulfstream-1 airborne platform over a four month period in 2013. Optical instrumentation included a CAPS PMex particle extinction monitor operating at 630 nm (Aerodyne Research), a photothermal interferometer (Brookhaven National Laboratory) measuring particle absorption at 632 nm and a 3 wavelength nephelometer (TSI). Information about the chemical evolution of the plumes was obtained primarily using a SP-AMS (Aerodyne Research) and a Single Particle Soot Photometer (SP2, Droplet Measurements). The chemical composition of the particulate emissions were characterized in the context of the fire location, combustion conditions, and optical property measurements, including extinction and single scattering albedos. The chemical composition of organic aerosol was found to be rapidly changing as a function of downwind location, with oxygen to carbon ratios increasing as a results of atmospheric aging processes (e.g., dilution, photochemistry). The single scattering albedo, (SSA) of plume aerosols increases downwind as the ratio of total particle extinction to carbon monoxide concentration (a marker for the plume dilution) increases, a finding that is related to changes in organic aerosol chemistry.

A stable isotope approach for source apportionment of chlorinated ethene plumes at a complex multi-contamination events urban site

NASA Astrophysics Data System (ADS)

Nijenhuis, Ivonne; Schmidt, Marie; Pellegatti, Eleonora; Paramatti, Enrico; Richnow, Hans Hermann; Gargini, Alessandro

2013-10-01

The stable carbon isotope composition of chlorinated aliphatic compounds such as chlorinated methanes, ethanes and ethenes was examined as an intrinsic fingerprint for apportionment of sources. A complex field site located in Ferrara (Italy), with more than 50 years history of use of chlorinated aliphatic compounds, was investigated in order to assess contamination sources. Several contamination plumes were found in a complex alluvial sandy multi-aquifer system close to the river Po; sources are represented by uncontained former industrial and municipal dump sites as well as by spills at industrial areas. The carbon stable isotope signature allowed distinguishing 2 major sources of contaminants. One source of chlorinated aliphatic contaminants was strongly depleted in 13C (<-60‰) suggesting production lines which have used depleted methane for synthesis. The other source had typical carbon isotope compositions of >-40‰ which is commonly observed in recent production of chlorinated solvents. The degradation processes in the plumes could be traced interpreting the isotope enrichment and depletion of parent and daughter compounds, respectively. We demonstrate that, under specific production conditions, namely when highly chlorinated ethenes are produced as by-product during chloromethanes production, 13C depleted fingerprinting of contaminants can be obtained and this can be used to track sources and address the responsible party of the pollution in urban areas.

A stable isotope approach for source apportionment of chlorinated ethene plumes at a complex multi-contamination events urban site.

PubMed

Nijenhuis, Ivonne; Schmidt, Marie; Pellegatti, Eleonora; Paramatti, Enrico; Richnow, Hans Hermann; Gargini, Alessandro

2013-10-01

The stable carbon isotope composition of chlorinated aliphatic compounds such as chlorinated methanes, ethanes and ethenes was examined as an intrinsic fingerprint for apportionment of sources. A complex field site located in Ferrara (Italy), with more than 50years history of use of chlorinated aliphatic compounds, was investigated in order to assess contamination sources. Several contamination plumes were found in a complex alluvial sandy multi-aquifer system close to the river Po; sources are represented by uncontained former industrial and municipal dump sites as well as by spills at industrial areas. The carbon stable isotope signature allowed distinguishing 2 major sources of contaminants. One source of chlorinated aliphatic contaminants was strongly depleted in ¹³C (<-60‰) suggesting production lines which have used depleted methane for synthesis. The other source had typical carbon isotope compositions of >-40‰ which is commonly observed in recent production of chlorinated solvents. The degradation processes in the plumes could be traced interpreting the isotope enrichment and depletion of parent and daughter compounds, respectively. We demonstrate that, under specific production conditions, namely when highly chlorinated ethenes are produced as by-product during chloromethanes production, ¹³C depleted fingerprinting of contaminants can be obtained and this can be used to track sources and address the responsible party of the pollution in urban areas. © 2013 Elsevier B.V. All rights reserved.

Monitoring eruptive activity at Mount St. Helens with TIR image data

USGS Publications Warehouse

Vaughan, R.G.; Hook, S.J.; Ramsey, M.S.; Realmuto, V.J.; Schneider, D.J.

2005-01-01

Thermal infrared (TIR) data from the MASTER airborne imaging spectrometer were acquired over Mount St. Helens in Sept and Oct, 2004, before and after the onset of recent eruptive activity. Pre-eruption data showed no measurable increase in surface temperatures before the first phreatic eruption on Oct 1. MASTER data acquired during the initial eruptive episode on Oct 14 showed maximum temperatures of ???330??C and TIR data acquired concurrently from a Forward Looking Infrared (FLIR) camera showed maximum temperatures ???675??C, in narrow (???1-m) fractures of molten rock on a new resurgent dome. MASTER and FLIR thermal flux calculations indicated a radiative cooling rate of ???714 J/m2/S over the new dome, corresponding to a radiant power of ???24 MW. MASTER data indicated the new dome was dacitic in composition, and digital elevation data derived from LIDAR acquired concurrently with MASTER showed that the dome growth correlated with the areas of elevated temperatures. Low SO2 concentrations in the plume combined with sub-optimal viewing conditions prohibited quantitative measurement of plume SO2. The results demonstrate that airborne TIR data can provide information on the temperature of both the surface and plume and the composition of new lava during eruptive episodes. Given sufficient resources, the airborne instrumentation could be deployed rapidly to a newly-awakening volcano and provide a means for remote volcano monitoring. Copyright 2005 by the American Geophysical Union.

Specific features of basalts from the western part of Andrew Bain Fault, Southwest Indian Ridge

NASA Astrophysics Data System (ADS)

Peyve, A. A.; Skolotnev, S. G.

2017-12-01

This paper reports original data on the composition of volcanic rocks in the western part of the Andrew Bain Fault of the South-West Indian Ridge obtained in the 23rd voyage of R/V Akademik Nikolai Strakhov. In accordance with high La/Th and low Nb/U ratios, the basalt compositions of stations S2317, S2318, and S2330 could result from melting of the DM-type source with HIMU traces. Meanwhile, the enriched samples of station S2326 correspond to a mantle source with a considerable contribution of recycled sediments (EM). Sample S2326/35, which is composed of a melt almost completely depleted in EM material, corresponds to the volcanic rocks of the Marion and Prince Edward islands. The obtained and available data on the SWIR segment from Bouvet Island to Andrew Bain Fault are indicative of small mantle heterogeneities in this region. Two possible variants of their origin are considered: either preservation of the enriched material fragments in the depleted mantle during the split of Gondwana or "contamination" of the mantle with plume material with the formation of vein irregularities before opening of the ocean in this region. In the latter case, the plume material could cover a huge area not constrained by the young plume magmatism regions on Bouvet, Marion, and Prince Edward islands.

Satellite measurements of SO2 emission and dispersion during the 2008-2009 eruption of Halema‘uma‘u, Kilauea

NASA Astrophysics Data System (ADS)

Carn, S. A.; Sutton, A. J.; Elias, T.; Patrick, M. R.; Owen, R. C.; Wu, S.

2009-12-01

Satellite remote sensing is providing unique constraints on sulfur dioxide (SO2) emissions associated with the ongoing eruption of Halema‘uma‘u (HMM), and daily observations of volcanic plume dispersion. We use synoptic SO2 measurements by the Ozone Monitoring Instrument (OMI) on NASA’s Aura satellite to chart the fluctuation in SO2 emissions and plume dispersion. Prior to the onset of degassing from HMM, OMI detected SO2 emissions from the east rift Pu‘u ‘O‘o vent; the average daily SO2 burden measured between Sept 6, 2004 and Feb 29, 2008 was 0.7 kilotons (kt) ±1 (1σ). The additional SO2 production from HMM caused total SO2 burdens in the composite Kilauea plume to increase notably in March-April 2008, and a daily average SO2 burden of ~4 kt ±4 (1σ) was measured by OMI between Mar 1, 2008 and Jul 31, 2009 (all burdens are preliminary and assume a SO2 plume altitude of 3 km). A total of ~2 Megatons of SO2 was measured by OMI in the Kilauea emissions between March 2008 and July 2009. The increased SO2 emissions provide an excellent opportunity to compare ground-based ultraviolet (UV) spectrometer and space-based UV OMI measurements of SO2 output, and test algorithms for derivation of emission rates from satellite data. Kilauea data analyzed to date show that trends in ground-based SO2 emission rates and OMI SO2 burdens are in qualitative agreement but differ in magnitude. Plume altitude is a critical factor in satellite SO2 retrievals, and interpretation of the Kilauea observations is complicated by the presence of two SO2 plumes (from HMM and Pu‘u ‘O‘o) within the OMI field-of-view. In order to constrain plume heights and SO2 lifetimes, we use plume simulations generated by the FLEXPART particle dispersion model and compare the model output with OMI SO2 observations. We validate the model-generated plume altitudes using vertical aerosol profiles derived from the CALIPSO space-borne lidar instrument. Gaussian plume models parameterized using visual observations of the HMM plume injection height further constrain near-source plume dispersion and downwind evolution. Refinement of SO2 altitude provides improved constraints on SO2 burdens in observed plumes. A more rigorous approach to deriving source emission strengths from satellite observations is an inverse modeling scheme incorporating measurements and models. Using Kilauea as a case study, we plan to develop such a scheme using OMI data, FLEXPART simulations and atmospheric chemistry and transport modeling using the GEOS-Chem model. Modeling of plume dispersion and chemistry will also provide estimates of SO2 and acid aerosol concentrations for potential use in air quality and health hazard assessments in Hawaii.

Lu-Hf isotopic memory of plume-lithosphere interaction in the source of layered mafic intrusions, Windimurra Igneous Complex, Yilgarn Craton, Australia

NASA Astrophysics Data System (ADS)

Nebel, O.; Arculus, R. J.; Ivanic, T. J.; Nebel-Jacobsen, Y. J.

2013-10-01

Most layered mafic intrusions (LMI) are formed via multiple magma injections into crustal magma chambers. These magmas are originally sourced from the mantle, likely via plume activity, but may interact with the overriding lithosphere during ascent and emplacement in the crust. The magma injections lead to the establishment of different layers and zones with complex macroscopic, microscopic and cryptic compositional layering through magmatic differentiation and associated cumulate formation, sometimes accompanied by crustal assimilation. These complex mineralogical and petrological processes obscure the nature of the mantle sources of LMI, and typically have limited the degree to which parental liquids can be fully characterised. Here, we present Lu-Hf isotope data for samples from distinct layers of the Upper Zone of the Windimurra Igneous Complex (WIC), an immense late-Archean LMI in the West Australian Yilgarn Craton. Lu-Hf isotope systematics of whole rocks are well correlated (MSWD=5.6, n=17) with an age of ˜3.05±0.05 Ga and initial ɛHf˜+8. This age, however, is older than whole rock Sm-Nd and zircon U-Pb ages of the intrusion, both of which are ca. 2.8 Ga. Stratigraphically-controlled initial Hf isotope variations (associated with multiple episodes of emplacement at ca. 2.8 Ga) indicate isotope mixing between a near-chondritic and an ultra-radiogenic component, the latter with ɛHf[2.8 Ga]>+15. This Hf isotope mixing creates a pseudochron-relationship at the time of intrusion of ˜250 Myr that is superimposed on subsequent radiogenic ingrowth after crystallisation, generating an age that predates the actual emplacement event. Mixing between late-stage crystallisation products (melt + crystals) from the Middle Zone and replenishing, plume-derived liquids was followed by crystal accumulation in a chemically evolving magma chamber. The ultra-radiogenic Hf isotope endmember in the WIC mantle source requires parent-daughter ratios consistent with very early formation in Earth history, akin to early Archean komatiitic plume sources. We propose that plume-derived melts that formed the Windimurra LMI reacted with ancient refractory lithospheric keels already underpinning ancient cratons, creating a melt with extremely high ɛHf[t]. Melting a refractory component with super-chondritic, time-integrated high Lu/Hf, in this case by plume-lithosphere interaction, simultaneously accounts for the extreme Hf isotope signals, Hf-Nd isotope decoupling, and difference in radiometric Lu-Hf and Sm-Nd ages.

Intense magmatic degassing through the lake of Copahue volcano, 2013-2014

NASA Astrophysics Data System (ADS)

Tamburello, G.; Agusto, M.; Caselli, A.; Tassi, F.; Vaselli, O.; Calabrese, S.; Rouwet, D.; Capaccioni, B.; Di Napoli, R.; Cardellini, C.; Chiodini, G.; Bitetto, M.; Brusca, L.; Bellomo, S.; Aiuppa, A.

2015-09-01

Here we report on the first assessment of volatile fluxes from the hyperacid crater lake hosted within the summit crater of Copahue, a very active volcano on the Argentina-Chile border. Our observations were performed using a variety of in situ and remote sensing techniques during field campaigns in March 2013, when the crater hosted an active fumarole field, and in March 2014, when an acidic volcanic lake covered the fumarole field. In the latter campaign, we found that 566 to 1373 t d-1 of SO2 were being emitted from the lake in a plume that appeared largely invisible. This, combined with our derived bulk plume composition, was converted into flux of other volcanic species (H2O ~ 10989 t d-1, CO2 ~ 638 t d-1, HCl ~ 66 t d-1, H2 ~ 3.3 t d-1, and HBr ~ 0.05 t d-1). These levels of degassing, comparable to those seen at many open-vent degassing arc volcanoes, were surprisingly high for a volcano hosting a crater lake. Copahue's unusual degassing regime was also confirmed by the chemical composition of the plume that, although issuing from a hot (65°C) lake, preserves a close-to-magmatic signature. EQ3/6 models of gas-water-rock interaction in the lake were able to match observed compositions and demonstrated that magmatic gases emitted to the atmosphere were virtually unaffected by scrubbing of soluble (S and Cl) species. Finally, the derived large H2O flux (10,988 t d-1) suggested a mechanism in which magmatic gas stripping drove enhanced lake water evaporation, a process likely common to many degassing volcanic lakes worldwide.

The petrogenesis of Gorgona komatiites, picrites and basalts: new field, petrographic and geochemical constraints

NASA Astrophysics Data System (ADS)

Kerr, A. C.; Marriner, G. F.; Arndt, N. T.; Tarney, J.; Nivia, A.; Saunders, A. D.; Duncan, R. A.

1996-04-01

Gorgona Island, Colombia is remarkable not only because it contains the only Phanerozoic komatiites, but also because it has mafic to ultramafic lavas with a wide range of compositions, from moderately enriched to extremely depleted (relative to Bulk Earth). The komatiite flows are, in many respects similar to Archaean komatiites; they formed from MgO-rich (18%) liquids and have upper spinifex zones and lower cumulate zones. The cumulate zones of Archaean komatiites contain many solid grains, in contrast more than 90% of the olivine in the Gorgona cumulates is highly skeletal. This combined with the fact that the Gorgona cumulate zones are thinner than those in Archaean komatiites, suggests that the komatiite magma became strongly superheated en route to the surface. The komatiites have trace element contents intermediate between those of the basalts and the ultramafic tuffs. Some basalts have isotope compositions indicative of long-term enrichment in incompatible elements, whereas other basalts and ultramafic volcanics have isotopic signatures that imply corresponding depletion. It is apparent that the plume source region of the Gorgona magmas was markedly heterogeneous, with at least two source components contributing to the observed variation in composition. This heterogeneity may have resulted from the incorporation of different components into the plume source, or it may be the result of complex melting and melt extraction processes during the ascent of a heterogeneous plume. Despite earlier suggestions that there may have been a significant age gap between depleted komatiite and basalt flows and the enriched basalts, new 40Ar- 39Ar dating of basalts and gabbros are more consistent with all being generated at 87 Ma during formation of the Caribbean/Colombian plateau, possibly at the Galapagos hotspot.

Hydrothermal plumes in the Gulf of Aden, as characterized by light transmission, Mn, Fe, CH4 and δ13C-CH4 anomalies

NASA Astrophysics Data System (ADS)

Gamo, Toshitaka; Okamura, Kei; Hatanaka, Hiroshi; Hasumoto, Hiroshi; Komatsu, Daisuke; Chinen, Masakazu; Mori, Mutsumi; Tanaka, Junya; Hirota, Akinari; Tsunogai, Urumu; Tamaki, Kensaku

2015-11-01

We conducted water column surveys to search for hydrothermal plumes over the spreading axes in the Gulf of Aden between 45°35‧E and 52°42‧E. We measured light transmission and chemical tracers Mn, Fe, CH4 and δ13C of CH4 in seawater taken using a CTD-Carrousel multi-sampling system at 12 locations including a control station in the Arabian Sea. We recognized three types of hydrothermal plumes at depths of 650 to 900 m (shallow plumes), 1000 to 1200 m (intermediate plumes), and >1500 m (deep plumes). The shallow plumes were apparently originated from newly discovered twin seamounts (12°03-06‧N and 45°35-41‧E) at the westernmost survey area, where two-dimensional distributions of light transmission and Mn were mapped by tow-yo observations of the CTD-sampling system with an in situ auto-analyzer GAMOS. The maximum concentrations of Mn, Fe, and CH4 of 46 nM, 251 nM, and 15 nM, respectively, were observed for collected seawater within the shallow plumes. The intermediate plumes were characterized by anomalies of light transmission, Mn, Fe, and δ13C of CH4, but by little CH4 anomalies, suggesting that CH4 had been consumed down to the background level during the aging of the plumes. Anomalies of δ3He already reported by the World Ocean Circulation Experiment (WOCE) program exhibited a hydrothermal plume-like peak at 2000 m depth in the Gulf of Aden, which seems to coincide with the deep plumes observed in this study. The endmember δ13C-CH4 values for the shallow and the deep plumes were estimated to be in a range between -10‰ and -15‰, demonstrating that the sources of CH4 are not biogenic but magmatic as similarly observed at sediment-starved mid-oceanic ridges.

Development of diapiric structures in the upper mantle due to phase transitions

NASA Technical Reports Server (NTRS)

Liu, M.; Yuen, D. A.; Zhao, W.; Honda, S.

1991-01-01

Solid-state phase transition in time-dependent mantle convection can induce diapiric flows in the upper mantle. When a deep mantle plume rises toward phase boundaries in the upper mantle, the changes in the local thermal buoyancy, local heat capacity, and latent heat associated with the phase change at a depth of 670 kilometers tend to pinch off the plume head from the feeding stem and form a diapir. This mechanism may explain episodic hot spot volcanism. The nature of the multiple phase boundaries at the boundary between the upper and lower mantle may control the fate of deep mantle plumes, allowing hot plumes to go through and retarding the tepid ones.

Instantaneous and time-averaged dispersion and measurement models for estimation theory applications with elevated point source plumes

NASA Technical Reports Server (NTRS)

Diamante, J. M.; Englar, T. S., Jr.; Jazwinski, A. H.

1977-01-01

Estimation theory, which originated in guidance and control research, is applied to the analysis of air quality measurements and atmospheric dispersion models to provide reliable area-wide air quality estimates. A method for low dimensional modeling (in terms of the estimation state vector) of the instantaneous and time-average pollutant distributions is discussed. In particular, the fluctuating plume model of Gifford (1959) is extended to provide an expression for the instantaneous concentration due to an elevated point source. Individual models are also developed for all parameters in the instantaneous and the time-average plume equations, including the stochastic properties of the instantaneous fluctuating plume.

Hubble Captures Volcanic Eruption Plume From Io

NASA Technical Reports Server (NTRS)

1997-01-01

The Hubble Space Telescope has snapped a picture of a 400-km-high (250-mile-high) plume of gas and dust from a volcanic eruption on Io, Jupiter's large innermost moon.

Io was passing in front of Jupiter when this image was taken by the Wide Field and Planetary Camera 2 in July 1996. The plume appears as an orange patch just off the edge of Io in the eight o'clock position, against the blue background of Jupiter's clouds. Io's volcanic eruptions blasts material hundreds of kilometers into space in giant plumes of gas and dust. In this image, material must have been blown out of the volcano at more than 2,000 mph to form a plume of this size, which is the largest yet seen on Io.

Until now, these plumes have only been seen by spacecraft near Jupiter, and their detection from the Earth-orbiting Hubble Space Telescope opens up new opportunities for long-term studies of these remarkable phenomena.

The plume seen here is from Pele, one of Io's most powerful volcanos. Pele's eruptions have been seen before. In March 1979, the Voyager 1 spacecraft recorded a 300-km-high eruption cloud from Pele. But the volcano was inactive when the Voyager 2 spacecraft flew by Jupiter in July 1979. This Hubble observation is the first glimpse of a Pele eruption plume since the Voyager expeditions.

Io's volcanic plumes are much taller than those produced by terrestrial volcanos because of a combination of factors. The moon's thin atmosphere offers no resistance to the expanding volcanic gases; its weak gravity (one-sixth that of Earth) allows material to climb higher before falling; and its biggest volcanos are more powerful than most of Earth's volcanos.

This image is a contrast-enhanced composite of an ultraviolet image (2600 Angstrom wavelength), shown in blue, and a violet image (4100 Angstrom wavelength), shown in orange. The orange color probably occurs because of the absorption and/or scattering of ultraviolet light in the plume. This light from Jupiter passes through the plume and is absorbed by sulfur dioxide gas or is scattered by fine dust, or both, while violet light passes through unimpeded. Future HST observations may be able to distinguish between the gas and dust explanations.

This image and other images and data received from the Hubble Space Telescope are posted on the World Wide Web on the Space Telescope Science Institute home page at URL http://oposite.stsci.edu/pubinfo/

Hydrocarbon Plume Dynamics in the Worldś Most Spectacular Hydrocarbon Seeps, Santa Barbara Channel, California

NASA Astrophysics Data System (ADS)

Mau, S.; Reed, J.; Clark, J.; Valentine, D.

2006-12-01

Large quantities of natural gas are emitted from the seafloor into the coastal ocean near Coal Oil Point, Santa Barbara Channel (SBC), California. Methane, ethane, and propane were quantified in the surface water at 79 stations in a 270 km2 area in order to map the surficial hydrocarbon plume and to quantify air-sea exchange of these gases. A time series was initiated for 14 stations to identify the variability of the mapped plume, and biologically-mediated oxidation rates of methane were measured to quantify the loss of methane in surface water. The hydrocarbon plume was found to comprise ~70 km2 and extended beyond study area. The plume width narrowed from 3 km near the source to 0.7 km further from the source, and then expanded to 6.7 km at the edge of the study area. This pattern matches the cyclonic gyre which is the normal current flow in this part of the Santa Barbara Channel - pushing water to the shore near the seep field and then broadening the plume while the water turns offshore further from the source. Concentrations of gaseous hydrocarbons decrease as the plume migrates. Time series sampling shows similar plume width and hydrocarbon concentrations when normal current conditions prevail. In contrast, smaller plume width and low hydrocarbon concentrations were observed when an additional anticyclonic eddy reversed the normal current flow, and a much broader plume with higher hydrocarbon concentrations was observed during a time of diminished speed within the current gyre. These results demonstrate that surface currents control hydrocarbon plume dynamics in the SBC, though hydrocarbon flux to the atmosphere is likely less dependent on currents. Estimates of air- sea hydrocarbon flux and biological oxidation rates will also be presented.

Utilizing NASA Airborne Data to Investigate the Influence of Fuel Type on Biomass Burning Aerosol Properties

NASA Astrophysics Data System (ADS)

Odwuor, A.; Corr, C.; Griffin, R. J.; Pusede, S.; Anderson, B.; Beyersdorf, A. J.; Campuzano Jost, P.; Chen, G.; Day, D. A.; Diskin, G. S.; Jimenez, J. L.; Moore, R.; Nault, B.; Schwarz, J. P.; Shook, M.; Thornhill, K. L., II; Winstead, E.; Armin, W.; Ziemba, L. D.

2017-12-01

Climate models and satellite aerosol classification retrievals rely on well-characterized aerosol optical properties (e.g., scattering and absorption coefficients) that vary with aerosol type. However, generalized parameterizations of aerosol optical properties are weakened by actual variability in aerosol chemical and physical properties that arises from factors independent of aerosol source (e.g., meteorology). This is particularly true for biomass burning (BB) aerosol, which can vary in composition and size depending on burn conditions (e.g., smoldering versus flaming) and fuel. This work investigates the relationships between BB aerosol chemical, physical, and optical properties and fuel. We compare BB aerosol measured in fire plumes associated with distinct fuel types sampled during three NASA airborne research campaigns: boreal forest fires during the Arctic Research of the Troposphere from Aircraft and Satellites (ARCTAS) mission in Saskatchewan, Canada in July 2008; agricultural fires during the Studies of Emissions and Atmospheric Composition, Clouds, and Climate Coupling by Regional Surveys (SEAC4RS) over the continental U.S. in August/September 2013; and scrubland fires during the Student Airborne Research Program (SARP) mission in Southern California, U.S. in June 2016. Mean modified combustion efficiency values between 0.9 and 0.92 for the agricultural plumes and between 0.92 and 0.99 for the boreal and scrubland plumes indicate a significant flaming component to these fires. Despite similarities in burn conditions, SSA at 550nm was consistently lower for the agricultural and scrubland fires ( 0.92) compared to the boreal forest ( 0.96). While the ratio of black carbon to organic aerosol (OA) was similar among fires, differences in the OA were noted; f44/f60 ratios derived from Aerosol Mass Spectrometer OA measurements were consistently higher (>5) in scrubland and agricultural fires compared to boreal forest fires (<5). This suggests the amount of oxidized OA relative to fresh BB aerosol in fire plumes under flaming conditions may vary with fuel type and influence plume optical properties. The relationship between size distributions and optical properties is also explored in this work, with particular attention on the role of the coarse mode in aerosol absorption.

Enhanced biodegradation by hydraulic heterogeneities in petroleum hydrocarbon plumes.

PubMed

Bauer, Robert D; Rolle, Massimo; Bauer, Sebastian; Eberhardt, Christina; Grathwohl, Peter; Kolditz, Olaf; Meckenstock, Rainer U; Griebler, Christian

2009-02-27

In case of dissolved electron donors and acceptors, natural attenuation of organic contaminant plumes in aquifers is governed by hydrodynamic mixing and microbial activity. Main objectives of this work were (i) to determine whether aerobic and anaerobic biodegradation in porous sediments is controlled by transverse dispersion, (ii) to elucidate the effect of sediment heterogeneity on mixing and biodegradation, and (iii) to search for degradation-limiting factors. Comparative experiments were conducted in two-dimensional sediment microcosms. Aerobic toluene and later ethylbenzene degradation by Pseudomonas putida strain F1 was initially followed in a plume developing from oxic to anoxic conditions and later under steady-state mixing-controlled conditions. Competitive anaerobic degradation was then initiated by introduction of the denitrifying strain Aromatoleum aromaticum EbN1. In homogeneous sand, aerobic toluene degradation was clearly controlled by dispersive mixing. Similarly, under denitrifying conditions, microbial activity was located at the plume's fringes. Sediment heterogeneity caused flow focusing and improved the mixing of reactants. Independent from the electron accepting process, net biodegradation was always higher in the heterogeneous setting with a calculated efficiency plus of 23-100% as compared to the homogeneous setup. Flow and reactive transport model simulations were performed in order to interpret and evaluate the experimental results.

Cenozoic magmatism throughout east Africa resulting from impact of a single plume

NASA Astrophysics Data System (ADS)

Ebinger, C. J.; Sleep, N. H.

1998-10-01

The geology of northern and central Africa is characterized by broad plateaux, narrower swells and volcanism occurring from ~45Myr ago to the present. The greatest magma volumes occur on the >1,000-km-wide Ethiopian and east African plateaux, which are transected by the Red Sea, Gulf of Aden and east African rift systems, active since the late Oligocene epoch. Evidence for one or more mantle plumes having impinged beneath the plateaux comes from the dynamic compensation inferred from gravity studies, the generally small degrees of extension observed and the geochemistry of voluminous eruptive products. Here we present a model of a single large plume impinging beneath the Ethiopian plateau that takes into account lateral flow and ponding of plume material in pre-existing zones of lithospheric thinning. We show that this single plume can explain the distribution and timing of magmatism and uplift throughout east Africa. The thin lithosphere beneath the Mesozoic-Palaeogene rifts and passive margins of Africa and Arabia guides the lateral flow of plume material west to the Cameroon volcanic line and south to the Comoros Islands. Our results demonstrate the strong control that the lithosphere exerts on the spatial distribution of plume-related melting and magmatism.

An experimental study on the near-source region of lazy turbulent plumes

NASA Astrophysics Data System (ADS)

Ciriello, Francesco; Hunt, Gary R.

2017-11-01

The near-source region of a `lazy' turbulent buoyant plume issuing from a circular source is examined for source Richardson numbers in the range of 101 to 107. New data is acquired for the radial contraction and streamwise variation of volume flux through an experimental programme of dye visualisations and particle image velocimetry. This data reveals the limited applicability of traditional entrainment laws used in integral modelling approaches for the description of the near-source region for these source Richardson numbers. A revised entrainment function is proposed, based on which we introduce a classification of plume behaviour whereby the degree of `laziness' may be expressed in terms of the excess dilution that occurs compared to a `pure' constant Richardson number plume. The increased entrainment measured in lazy plumes is attributed to Rayleigh-Taylor instabilities developing along the contraction of the plume which promote the additional engulfment of ambient fluid into the plume. This work was funded by an EPSRC Industial Case Award sponsored by Dyson Technology Ltd. Special thanks go to the members of the Dyson Environmental Control Group that regularly visit us in Cambridge for discussions about our work.

SIZE AND COMPOSITION OF VISIBILITY-REDUCING AEROSOLS IN SOUTHWESTERN PLUMES

EPA Science Inventory

The southwestern United States desert and mountain areas are generally characterized by very good visibility. Until recent years, scenic vistas of natural landmarks and mountains with a visual range of over 100 miles were common. These vistas have been considered a major resource...

Evaluation of Visible Plumes.

ERIC Educational Resources Information Center

Brennan, Thomas

Developed for presentation at the 12th Conference on Methods in Air Pollution and Industrial Hygiene Studies, University of Southern California, April, 1971, this outline discusses plumes with contaminants that are visible to the naked eye. Information covers: (1) history of air pollution control regulations, (2) need for methods of evaluating…

Aged particles derived from emissions of coal-fired power plants: The TERESA field results

PubMed Central

Kang, Choong-Min; Gupta, Tarun; Ruiz, Pablo A.; Wolfson, Jack M.; Ferguson, Stephen T.; Lawrence, Joy E.; Rohr, Annette C.; Godleski, John; Koutrakis, Petros

2013-01-01

The Toxicological Evaluation of Realistic Emissions Source Aerosols (TERESA) study was carried out at three US coal-fired power plants to investigate the potential toxicological effects of primary and photochemically aged (secondary) particles using in situ stack emissions. The exposure system designed successfully simulated chemical reactions that power plant emissions undergo in a plume during transport from the stack to receptor areas (e.g., urban areas). Test atmospheres developed for toxicological experiments included scenarios to simulate a sequence of atmospheric reactions that can occur in a plume: (1) primary emissions only; (2) H2SO4 aerosol from oxidation of SO2; (3) H2SO4 aerosol neutralized by gas-phase NH3; (4) neutralized H2SO4 with secondary organic aerosol (SOA) formed by the reaction of α-pinene with O3; and (5) three control scenarios excluding primary particles. The aged particle mass concentrations varied significantly from 43.8 to 257.1 μg/m3 with respect to scenario and power plant. The highest was found when oxidized aerosols were neutralized by gas-phase NH3 with added SOA. The mass concentration depended primarily on the ratio of SO2 to NOx (particularly NO) emissions, which was determined mainly by coal composition and emissions controls. Particulate sulfate (H2SO4 + neutralized sulfate) and organic carbon (OC) were major components of the aged particles with added SOA, whereas trace elements were present at very low concentrations. Physical and chemical properties of aged particles appear to be influenced by coal type, emissions controls and the particular atmospheric scenarios employed. PMID:20462390

Velocity control as a tool for optimal plume containment in the Equus Beds aquifer, Kansas

USGS Publications Warehouse

Heidari, M.; Sadeghipour, J.; Drici, O.

1987-01-01

A ground-water-management model was developed to investigate the best management options for the containment of an oil-field-brine plume in the Equus Beds aquifer in south-central Kansas. The main purpose of the management model was to find the optimal locations and minimum rates of pumpage of a set of plume-interception wells, to successfully reverse the velocity vectors at observation wells located along the plume front, and also to satisfy freshwater demands from supply wells. The effects of the calculated minimum withdrawals from the interception wells on the migration of contaminants throughout the ground-water system were evaluated utilizing a solute-transport model. This latter analysis was carried out to ensure the containment of the plume. Whereas application of the management model to the study area achieves the management objectives, the implementation of the results is believed to be impractical and expensive.

Enceladus Plumes: Causes of Decadal Variability

NASA Astrophysics Data System (ADS)

Ingersoll, Andrew P.; Ewald, Shawn P.

2016-10-01

The Enceladus plumes have decreased over the decade that Cassini has been observing them. This long-term variation is superposed on the much shorter-term variation tied to the position of Enceladus in its orbit around Saturn. The observations are ISS and VIMS images, which reveal the particles in the plumes but not the gas. The decadal variability largely consists of a 2-fold decline in the mass of plume material, but there is a hint of a recent turnaround. Here we offer three hypotheses, each with its strengths and weaknesses, to explain the long-term variability. The first is seasonal change, from summer to fall in the southern hemisphere. The loss of sunlight could increase the build-up of ice around the tiger stripes. The weakness is that the sunlight is likely to have a small effect, e.g., decreasing the sublimation rate of the ice by only ~1 cm/year. The second hypothesis is a statistical fluctuation in the number of active plumes, which tend to turn themselves off due to build-up of ice at the throat of the vent. The weakness is that the plumes are likely to fluctuate independently, and if there are ~100 plumes, their sum will only fluctuate by 10%. The third hypothesis is that the variation is part of a well-known decadal cycle of orbital eccentricity, which varies by ±2.5% around a mean of 0.0047. The peak eccentricity occurred in 2009-2010, and the minimum occurred in 2015. Since eccentricity controls the short-term orbital cycle variations, it could also control the longer-term decadal variations. The weakness is that the eccentricity variation is small, from 0.0046 to 0.0048. It is not certain that such a small variation could cause a 2-fold variation in the strength of the plumes. An independent study, still in its infancy, is the possibility that liquid water reaches the surface during part of the orbital cycle.

The salinity signature of the cross-shelf exchanges in the Southwestern Atlantic Ocean: Numerical simulations.

PubMed

Matano, Ricardo P; Combes, Vincent; Piola, Alberto R; Guerrero, Raul; Palma, Elbio D; Ted Strub, P; James, Corinne; Fenco, Harold; Chao, Yi; Saraceno, Martin

2014-11-01

A high-resolution model is used to characterize the dominant patterns of sea surface salinity (SSS) variability generated by the freshwater discharges of the Rio de la Plata (RdlP) and the Patos/Mirim Lagoon in the southwestern Atlantic region. We identify three dominant modes of SSS variability. The first two, which have been discussed in previous studies, represent the seasonal and the interannual variations of the freshwater plumes over the continental shelf. The third mode of SSS variability, which has not been discussed hitherto, represents the salinity exchanges between the shelf and the deep ocean. A diagnostic study using floats and passive tracers identifies the pathways taken by the freshwater plumes. During the austral winter (JJA) , the plumes leave the shelf region north of the BMC. During the austral summer (DJF), the plumes are entrained more directly into the BMC. A sensitivity study indicates that the high - frequency component of the wind stress forcing controls the vertical structure of the plumes while the low-frequency component of the wind stress forcing and the interannual variations of the RdlP discharge controls the horizontal structure of the plumes. Dynamical analysis reveals that the cross-shelf flow has a dominant barotropic structure and, therefore, the SSS anomalies detected by Aquarius represent net mass exchanges between the shelf and the deep ocean. The net cross-shelf volume flux is 1.21 Sv. This outflow is largely compensated by an inflow from the Patagonian shelf.

The salinity signature of the cross-shelf exchanges in the Southwestern Atlantic Ocean: Numerical simulations

PubMed Central

Matano, Ricardo P; Combes, Vincent; Piola, Alberto R; Guerrero, Raul; Palma, Elbio D; Ted Strub, P; James, Corinne; Fenco, Harold; Chao, Yi; Saraceno, Martin

2014-01-01

A high-resolution model is used to characterize the dominant patterns of sea surface salinity (SSS) variability generated by the freshwater discharges of the Rio de la Plata (RdlP) and the Patos/Mirim Lagoon in the southwestern Atlantic region. We identify three dominant modes of SSS variability. The first two, which have been discussed in previous studies, represent the seasonal and the interannual variations of the freshwater plumes over the continental shelf. The third mode of SSS variability, which has not been discussed hitherto, represents the salinity exchanges between the shelf and the deep ocean. A diagnostic study using floats and passive tracers identifies the pathways taken by the freshwater plumes. During the austral winter (JJA), the plumes leave the shelf region north of the BMC. During the austral summer (DJF), the plumes are entrained more directly into the BMC. A sensitivity study indicates that the high-frequency component of the wind stress forcing controls the vertical structure of the plumes while the low-frequency component of the wind stress forcing and the interannual variations of the RdlP discharge controls the horizontal structure of the plumes. Dynamical analysis reveals that the cross-shelf flow has a dominant barotropic structure and, therefore, the SSS anomalies detected by Aquarius represent net mass exchanges between the shelf and the deep ocean. The net cross-shelf volume flux is 1.21 Sv. This outflow is largely compensated by an inflow from the Patagonian shelf. PMID:26213673

The salinity signature of the cross-shelf exchanges in the Southwestern Atlantic Ocean: Numerical simulations

NASA Astrophysics Data System (ADS)

Matano, Ricardo P.; Combes, Vincent; Piola, Alberto R.; Guerrero, Raul; Palma, Elbio D.; Ted Strub, P.; James, Corinne; Fenco, Harold; Chao, Yi; Saraceno, Martin

2014-11-01

A high-resolution model is used to characterize the dominant patterns of sea surface salinity (SSS) variability generated by the freshwater discharges of the Rio de la Plata (RdlP) and the Patos/Mirim Lagoon in the southwestern Atlantic region. We identify three dominant modes of SSS variability. The first two, which have been discussed in previous studies, represent the seasonal and the interannual variations of the freshwater plumes over the continental shelf. The third mode of SSS variability, which has not been discussed hitherto, represents the salinity exchanges between the shelf and the deep ocean. A diagnostic study using floats and passive tracers identifies the pathways taken by the freshwater plumes. During the austral winter (JJA), the plumes leave the shelf region north of the BMC. During the austral summer (DJF), the plumes are entrained more directly into the BMC. A sensitivity study indicates that the high-frequency component of the wind stress forcing controls the vertical structure of the plumes while the low-frequency component of the wind stress forcing and the interannual variations of the RdlP discharge controls the horizontal structure of the plumes. Dynamical analysis reveals that the cross-shelf flow has a dominant barotropic structure and, therefore, the SSS anomalies detected by Aquarius represent net mass exchanges between the shelf and the deep ocean. The net cross-shelf volume flux is 1.21 Sv. This outflow is largely compensated by an inflow from the Patagonian shelf.

Simulating oil droplet dispersal from the Deepwater Horizon spill with a Lagrangian approach

USGS Publications Warehouse

North, Elizabeth W.; Schlag, Zachary; Adams, E. Eric; Sherwood, Christopher R.; He, Ruoying; Hyun, Hoon; Socolofsky, Scott A.

2011-01-01

An analytical multiphase plume model, combined with time-varying flow and hydrographic fields generated by the 3-D South Atlantic Bight and Gulf of Mexico model (SABGOM) hydrodynamic model, were used as input to a Lagrangian transport model (LTRANS), to simulate transport of oil droplets dispersed at depth from the recent Deepwater Horizon MC 252 oil spill. The plume model predicts a stratification-dominated near field, in which small oil droplets detrain from the central plume containing faster rising large oil droplets and gas bubbles and become trapped by density stratification. Simulated intrusion (trap) heights of ∼ 310–370 m agree well with the midrange of conductivity-temperature-depth observations, though the simulated variation in trap height was lower than observed, presumably in part due to unresolved variability in source composition (percentage oil versus gas) and location (multiple leaks during first half of spill). Simulated droplet trajectories by the SABGOM-LTRANS modeling system showed that droplets with diameters between 10 and 50 μm formed a distinct subsurface plume, which was transported horizontally and remained in the subsurface for >1 month. In contrast, droplets with diameters ≥90 μm rose rapidly to the surface. Simulated trajectories of droplets ≤50 μm in diameter were found to be consistent with field observations of a southwest-tending subsurface plume in late June 2010 reported by Camilli et al. [2010]. Model results suggest that the subsurface plume looped around to the east, with potential subsurface oil transport to the northeast and southeast. Ongoing work is focusing on adding degradation processes to the model to constrain droplet dispersal.

Time-series analysis of two hydrothermal plumes at 9°50'N East Pacific Rise reveals distinct, heterogeneous bacterial populations.

PubMed

Sylvan, J B; Pyenson, B C; Rouxel, O; German, C R; Edwards, K J

2012-03-01

We deployed sediment traps adjacent to two active hydrothermal vents at 9°50'N on the East Pacific Rise (EPR) to assess the variability in bacterial community structure associated with plume particles on the timescale of weeks to months, to determine whether an endemic population of plume microbes exists, and to establish ecological relationships between bacterial populations and vent chemistry. Automated rRNA intergenic spacer analysis (ARISA) indicated that there are separate communities at the two different vents and temporal community variations between each vent. Correlation analysis between chemistry and microbiology indicated that shifts in the coarse particulate (>1 mm) Fe/(Fe+Mn+Al), Cu, V, Ca, Al, (232) Th, and Ti as well as fine-grained particulate (<1 mm) Fe/(Fe+Mn+Al), Fe, Ca, and Co are reflected in shifts in microbial populations. 16S rRNA clone libraries from each trap at three time points revealed a high percentage of Epsilonproteobacteria clones and hyperthermophilic Aquificae. There is a shift toward the end of the experiment to more Gammaproteobacteria and Alphaproteobacteria, many of whom likely participate in Fe and S cycling. The particle-attached plume environment is genetically distinct from the surrounding seawater. While work to date in hydrothermal environments has focused on determining the microbial communities on hydrothermal chimneys and the basaltic lavas that form the surrounding seafloor, little comparable data exist on the plume environment that physically and chemically connects them. By employing sediment traps for a time-series approach to sampling, we show that bacterial community composition on plume particles changes on timescales much shorter than previously known. © 2012 Blackwell Publishing Ltd.

Tephra dispersal during the Campanian Ignimbrite (Italy) eruption: implications for ultra-distal ash transport during the large caldera-forming eruption

NASA Astrophysics Data System (ADS)

Smith, Victoria C.; Isaia, Roberto; Engwell, Sam L.; Albert, Paul. G.

2016-06-01

The Campanian Ignimbrite eruption dispersed ash over much of the central eastern Mediterranean Sea and eastern Europe. The eruption started with a Plinian phase that was followed by a series of pyroclastic density currents (PDCs) associated with the collapse of the Plinian column and the caldera. The glass compositions of the deposits span a wide geochemical range, but the Plinian fallout and PDCs associated with column collapse, the Lower Pumice Flow, only erupted the most evolved compositions. The later PDCs, the Breccia Museo and Upper Pumice Flow, erupted during and after caldera collapse, tap a less evolved component, and intermediate compositions that represent mixing between the end-members. The range of glass compositions in the Campanian Ignimbrite deposits from sites across the central and eastern Mediterranean Sea allow us to trace the dispersal of the different phases of this caldera-forming eruption. We map the fallout from the Plinian column and the plumes of fine material associated with the PDCs (co-PDCs) across the entire dispersal area. This cannot be done using the usual grain-size methods as deposits in these distal regions do not retain characteristics that allow attribution to either the Plinian or co-PDC phases. The glass compositions of the tephra at ultra-distal sites (>1500 km from the vent) match those of the uppermost PDC units, suggesting that most of the ultra-distal dispersal was associated with the late co-PDC plume that was generated during caldera collapse.

Enceladus Life Finder: Search for Life in a Habitable Moon.

NASA Astrophysics Data System (ADS)

Lunine, J. I.; Waite, J. H., Jr.; Spilker, L. J.; Postberg, F.; Cable, M. L.; Srama, R.; Clark, K.; Lee, S. W.

2015-12-01

A thousand times smaller in mass than Ganymede, Enceladus was known from Voyager data to be extremely bright and a dearth of craters on some parts of its surface suggested geologic activity. Cassini discovered the presence and composition of a plume erupting from the south polar terrain of Enceladus, approximately 100 narrow, distinct "geysers" or "jets" that feed it, and anomalous thermal signatures along fractures from which the geysers erupt. Cassini discovered organic and nitrogen-bearing molecules in the plume vapor, and detected salts in the plume icy grains, arguing strongly for ocean water being in contact with a rocky core. As much as Cassini has done, it cannot tell us whether the ocean of Enceladus hosts an active biota today. Enceladus Life Finder (ELF) is a Discovery-class solar-powered Saturn orbiter designed to fly multiple times through the plume of Enceladus. It carries two state-of-the-art mass spectrometers designed to analyze the gas and grains in the plume. The goals of the mission are derived directly from the most recent decadal survey: first, to determine primordial sources of organics and sites of organic synthesis today, second, to determine if there are modern habitats in the solar system beyond Earth where the conditions for life exist today and third, if life exists there now. ELF conducts three tests for life. The first test looks for a non-abiotic distribution of amino acids, the second determines whether the carbon number distribution in fatty acids or isoprenoids is biased toward a particular rule, and the third measures carbon and hydrogen isotopic ratios, together with the abundance of methane relative to other alkanes, to assess whether the values fall in the range for biological processes. The ELF mission spacecraft conducts ten science plume fly-throughs; the baseline science is completed in the first five plume passages.

Temporal Variations in Hotspot Volcanic Production Caused by Interactions Between Upwelling Mantle Plumes and Phase Transitions

NASA Astrophysics Data System (ADS)

Neuharth, D. J.; Mittelstaedt, E. L.

2017-12-01

Observations at numerous hotspots around the globe, such as Hawaii and Louisville, find periodic variations in volcanic production with time. For example, the volcanic production rate along the Hawaiian seamount chain varies from 0.05 to 0.25 km3/yr at periods of 15 Myr, while volcanic production rate along the Louisville seamount chain has consistently declined over the past 40 Myr. One possible explanation for these variations is long-term interaction of upwelling mantle plumes with mantle phase transitions. While previous studies carefully quantify the initial interaction and subsequent penetration or inhibition of a plume as it encounters the 660 km phase boundary and traverses the transition zone, the long-term interaction of plume upwelling and phase boundaries in the mantle is not well constrained. To assess the impact of plume-phase transition interaction on observed variability in hotspot volcanic output, we use the Advanced Solver for Problems in Earth's ConvecTion (ASPECT) code to numerically simulate upwelling of an isolated plume under the Anelastic Liquid Approximation (ALA). We use an axisymmetric 2D shell geometry with a 60° opening width and mantle thickness of 2855 km. Plume upwelling is initiated by imposing anomalously warm (ΔT 250 K) temperatures across a zone 200 km wide centered at the base of the model. At the 660 km and 410 km depth mantle phase transitions we simulate changes in density, viscosity, and the release of latent heat. Models are allowed to evolve for up to 1 Gyr. To test the effect of differing mantle compositions, we vary the Clapeyron slopes from 1 to 5 MPa and -0.5 to -6 MPa at the 410 km and 660 km phase transitions, respectively. Similar to other studies, results of preliminary simulations show an initial flattening of the plume head at the 660 km transition before penetration and subsequent acceleration across the 410 km transition, coinciding with mild shoaling of the 660 km, and deepening of the 410 km. Here, we will present analyses of mass flux periodicity and near-surface melt production rates and the implications on hotspot volcanic production rates.

Gaseous and Particulate Content of Laser Hair Removal Plume.

PubMed

Chuang, Gary S; Farinelli, William; Christiani, David C; Herrick, Robert F; Lee, Norman C Y; Avram, Mathew M

2016-12-01

Potentially harmful chemicals are released when tissues are vaporized. Laser hair removal (LHR) causes heating and often vaporization of hairs, producing both a signature malodorous plume and visible particulates. To characterize the chemical composition and quantify the ultrafine particle content of the plume generated during LHR. In the laser center of a large academic hospital, discarded terminal hairs from the trunk and extremities were collected from 2 adult volunteers. The hair samples were sealed in glass gas chromatography chambers and treated with a laser. The laser plume was analyzed by gas chromatography-mass spectrometry (GC-MS). During LHR treatment, two 6-L negative pressure canisters were used to capture 30 seconds of laser plume, and a portable condensation particle counter was used to measure ultrafine particulates (<1 µm). Ultrafine particle concentrations were measured within the treatment room, within the waiting room, and outside the building. The chemical content of the laser plume was analyzed with GC-MS and screened for aerosolized toxins using Environmental Protection Agency-certified methods. The ambient concentration of ultrafine particles during LHR was measured by condensation particle counters. Analysis with GC-MS identified 377 chemical compounds. Sixty-two of these compounds, of which 13 are known or suspected carcinogens and more than 20 are known environmental toxins, exhibited strong absorption peaks. During LHR, the portable condensation particle counters documented an 8-fold increase compared with the ambient room baseline level of ultrafine particle concentrations (ambient room baseline, 15 300 particles per cubic centimeter [ppc]; LHR with smoke evacuator, 129 376 ppc), even when a smoke evacuator was in close proximity (5.0 cm) to the procedure site. When the smoke evacuator was turned off for 30 seconds, there was a more than 26-fold increase in particulate count compared with ambient baseline levels (ambient baseline, 15 300 ppc; LHR without smoke evacuator for 30 seconds, 435 888 ppc). These findings establish the concern that the burning-hair plume often present during LHR should be considered a biohazard, warranting the use of smoke evacuators, good ventilation, and respiratory protection, especially for health care workers with prolonged exposure to LHR plume.

Gaseous composition measured by a chemical ionization mass spectrometer in fresh and aged ship plumes

NASA Astrophysics Data System (ADS)

Faxon, Cameron; Psichoudaki, Magda; Kuuluvainen, Heino; Hallquist, Åsa; Thomson, Erik; Pettersson, Jan; Hallquist, Mattias

2015-04-01

The port of Gothenburg is the largest port of the Nordic countries with numerous ships calling the port daily. The ship exhausts contain numerous pollutants including gases such as SO2 and NOx as well as particulate matter and soot. The exhaust also contains numerous organic compounds, a large fraction of which are unidentified. These organics are oxidized in the atmosphere producing more oxygenated and potentially less volatile compounds that may contribute to the secondary organic aerosol (SOA). This work focuses on the characterization of fresh gaseous species present in the exhaust plumes of the passing ships and also on their photochemical aging. Between 26 September and 12 November 2014 measurements were conducted at a sampling site located on a small peninsula at the entrance of Gothenburg's port. The campaign was divided in two periods. During the first period, the fresh plumes of the passing ships were measured through a main inlet. During the second period, the sample passed through the same inlet and was then introduced into a Potential Aerosol Mass (PAM) reactor. The PAM reactor uses UV lamps and high concentrations of oxidants (OH radicals and O3) to oxidize the organic species present in the plumes. The oxidation that takes place within the reactor can be equivalent to up to one week of atmospheric oxidation. Preliminary tests showed that the oxidation employed in the current camping corresponded to 3.4 days in the atmosphere. A Time-of-Flight Chemical Ionization Mass Spectrometer (ToF-CIMS) was employed to monitor the concentration of different organic species present in the fresh and aged plumes. Water (positive) and iodide (negative) ionization methods were employed were water was primarily used for fresh plumes (large fraction of non-polar compounds) while iodide was used for the aged plumes (primarily oxidised products). The H2O, O3 and SO2 concentrations inside the PAM chamber were monitored, and an organic tracer for OH exposure determination was also continuously measured. The dominant species concentrations of both fresh and aged ship plumes are presented and their emission factors are estimated from concurrent CO2 measurements.

Boninite-like intraplate magmas from Manihiki Plateau require ultra-depleted and enriched source components

PubMed Central

Golowin, Roman; Portnyagin, Maxim; Hoernle, Kaj; Hauff, Folkmar; Gurenko, Andrey; Garbe-Schönberg, Dieter; Werner, Reinhard; Turner, Simon

2017-01-01

The Ontong Java and Manihiki oceanic plateaus are believed to have formed through high-degree melting of a mantle plume head. Boninite-like, low-Ti basement rocks at Manihiki, however, imply a more complex magma genesis compared with Ontong Java basement lavas that can be generated by ∼30% melting of a primitive mantle source. Here we show that the trace element and isotope compositions of low-Ti Manihiki rocks can best be explained by re-melting of an ultra-depleted source (possibly a common mantle component in the Ontong Java and Manihiki plume sources) re-enriched by ≤1% of an ocean-island-basalt-like melt component. Unlike boninites formed via hydrous flux melting of refractory mantle at subduction zones, these boninite-like intraplate rocks formed through adiabatic decompression melting of refractory plume material that has been metasomatized by ocean-island-basalt-like melts. Our results suggest that caution is required before assuming all Archaean boninites were formed in association with subduction processes. PMID:28181497

Subglacial discharge-driven renewal of tidewater glacier fjords

NASA Astrophysics Data System (ADS)

Carroll, Dustin; Sutherland, David A.; Shroyer, Emily L.; Nash, Jonathan D.; Catania, Ginny A.; Stearns, Leigh A.

2017-08-01

The classic model of fjord renewal is complicated by tidewater glacier fjords, where submarine melt and subglacial discharge provide substantial buoyancy forcing at depth. Here we use a suite of idealized, high-resolution numerical ocean simulations to investigate how fjord circulation driven by subglacial plumes, tides, and wind stress depends on fjord width, grounding line depth, and sill height. We find that the depth of the grounding line compared to the sill is a primary control on plume-driven renewal of basin waters. In wide fjords the plume exhibits strong lateral recirculation, increasing the dilution and residence time of glacially-modified waters. Rapid drawdown of basin waters by the subglacial plume in narrow fjords allows for shelf waters to cascade deep into the basin; wide fjords result in a thin, boundary current of shelf waters that flow toward the terminus slightly below sill depth. Wind forcing amplifies the plume-driven exchange flow; however, wind-induced vertical mixing is limited to near-surface waters. Tidal mixing over the sill increases in-fjord transport of deep shelf waters and erodes basin stratification above the sill depth. These results underscore the first-order importances of fjord-glacier geometry in controlling circulation in tidewater glacier fjords and, thus, ocean heat transport to the ice.

Evolving a Neural Olfactorimotor System in Virtual and Real Olfactory Environments

PubMed Central

Rhodes, Paul A.; Anderson, Todd O.

2012-01-01

To provide a platform to enable the study of simulated olfactory circuitry in context, we have integrated a simulated neural olfactorimotor system with a virtual world which simulates both computational fluid dynamics as well as a robotic agent capable of exploring the simulated plumes. A number of the elements which we developed for this purpose have not, to our knowledge, been previously assembled into an integrated system, including: control of a simulated agent by a neural olfactorimotor system; continuous interaction between the simulated robot and the virtual plume; the inclusion of multiple distinct odorant plumes and background odor; the systematic use of artificial evolution driven by olfactorimotor performance (e.g., time to locate a plume source) to specify parameter values; the incorporation of the realities of an imperfect physical robot using a hybrid model where a physical robot encounters a simulated plume. We close by describing ongoing work toward engineering a high dimensional, reversible, low power electronic olfactory sensor which will allow olfactorimotor neural circuitry evolved in the virtual world to control an autonomous olfactory robot in the physical world. The platform described here is intended to better test theories of olfactory circuit function, as well as provide robust odor source localization in realistic environments. PMID:23112772

Life Cycle of Mantle Plumes: A perspective from the Galapagos Plume (Invited)

NASA Astrophysics Data System (ADS)

Gazel, E.; Herzberg, C. T.

2009-12-01

Hotspots are localized sources of heat and magmatism considered as modern-day evidence of mantle plumes. Some hotspots are related to massive magmatic production that generated Large Igneous Provinces (LIPS), an initial-peak phase of plume activity with a mantle source hotter and more magmatically productive than present-day hotspots. Geological mapping and geochronological studies have shown much lower eruption rates for OIB compared to lavas from Large Igneous Provinces LIPS such as oceanic plateaus and continental flood provinces. Our study is the first quantitative petrological comparison of mantle source temperatures and extent of melting for OIB and LIP sources. The wide range of primary magma compositions and inferred mantle potential temperatures for each LIP and OIB occurrence suggest that this rocks originated form a hotspot, a spatially localized source of heat and magmatism restricted in time. Extensive outcrops of basalt, picrite, and sometimes komatiite with circa 65-95 Ma ages occupy portions of the pacific shore of Central and South America included in the Caribbean Large Igneous Province (CLIP). There is general consensus of a Pacific-origin of CLIP and most studies suggest that it was produced by melting in the Galapagos mantle plume. The Galapagos connection is consistent with isotopic and geochemical similarities with lavas from the present-day Galapagos hotspot. A Galapagos link for rocks in South American oceanic complexes (eg. the island of Gorgona) is more controversial and requires future work. The MgO and FeO contents of lavas from the Galapagos related lavas and their primary magmas have decreased since the Cretaceous. From petrological modeling we infer that these changes reflect a cooling of the Galapagos mantle plume from a potential temperature of 1560-1620 C in the Cretaceous to 1500 C at the present time. These temperatures are higher than 1350 C for ambient mantle associated with oceanic ridges, and provide support for the mantle plume model of the CLIP. The exact form of the secular cooling curve depends on whether the Gorgona komatiites were produced by the Galapagos or another plume. Iceland also exhibits secular cooling, in agreement with previous studies. In general, mantle plumes for LIPS with Paleocene-Permian ages were hotter and melted more extensively than plumes of more modern oceanic islands. This is interpreted to reflect episodic flow from lower mantle domains that are lithologically and geochemically heterogeneous. The majority of lavas from the present-day Galapagos plume formed in a column where melting ended at pressures less than 2 GPa, and this pressure is highly variable. Melting ended at much lower pressures for lavas from the Cocos and Carnegie Ridges, consistent with the channeling of the Galapagos plume to locations of thinner lithosphere. Low pressures of final melting are also inferred for older CLIP lavas, which suggest that the plume head impacted a mid-ocean ridge system.

Efficacy of controlled-release KMnO4 (CRP) for controlling dissolved TCE plume in groundwater: a large flow-tank study.

PubMed

Lee, Byung Sun; Kim, Jeong Hee; Lee, Ki Churl; Kim, Yang Bin; Schwartz, Franklin W; Lee, Eung Seok; Woo, Nam Chil; Lee, Myoung Ki

2009-02-01

A well-based, reactive barrier system using controlled-release potassium permanganate (CRP system) was recently developed as a long-term treatment option for dilute plumes of chlorinated solvents in groundwater. In this study, we performed large-scale (L x W x D = 8 m x 4 m x 2 m) flow-tank experiments to examine remedial efficacy of the CRP system. A total of 110 CRP rods (OD x L=5 cm x 150 cm) were used to construct a well-based CRP system (L x W x D = 3 m x 4 m x 1.5 m) comprising three discrete barriers installed at 1-m interval downstream. Natural sands having oxidant demand of 3.7 g MnO(4)(-)kg(-1) for 500 mg L(-1)MnO(4)(-) were used as porous media. After MnO(4)(-) concentrations were somewhat stabilized (0.5-6.0 mg L(-1)), trichloroethylene (TCE) plume was flowed through the flow-tank for 53 d by supplying 1.19 m(3)d(-1) of TCE solution. Mean initial TCE concentrations were 87 microg L(-1) for first 20 d and 172 microg L(-1) for the next 33 d. During TCE treatment, flow velocity (0.60md(-1)), pH (7.0-8.2), and concentrations of dissolved metals ([Al]=0.7 mg L(-1), [Fe]=0.01 mg L(-1)) showed little variations. The MnO(2)(s) contents in the sandy media measured after the TCE treatment ranged from 21 to 26 mg kg(-1), slightly increased from mean baseline value of 17 mg kg(-1). Strengths of the TCE plume considerably diminished by the CRP system. For the 87 microg L(-1) plume, TCE concentrations decreased by 38% (53), 67% (29), and 74% (23 microg L(-1)) after 1st, 2nd, and 3rd barriers, respectively. For the 172 microg L(-1) plume, TCE concentrations decreased by 27% (125), 46% (93), and 65% (61 microg L(-1)) after 1st, 2nd, and 3rd barriers, respectively. Incomplete destruction of TCE plume was attributed to the lack of lateral dispersion in the unpumped well-based barrier system. Development of delivery systems that can facilitate lateral spreading and mixing of permanganate with contaminant plume is warranted.

A numerical study of the Magellan Plume

NASA Astrophysics Data System (ADS)

Palma, Elbio D.; Matano, Ricardo P.

2012-05-01

In this modeling study we investigate the dynamical mechanisms controlling the spreading of the Magellan Plume, which is a low-salinity tongue that extends along the Patagonian Shelf. Our results indicate that the overall characteristics of the plume (width, depth, spreading rate, etc.) are primarily influenced by tidal forcing, which manifests through tidal mixing and tidal residual currents. Tidal forcing produces a homogenization of the plume's waters and an offshore displacement of its salinity front. The interaction between tidal and wind-forcing reinforces the downstream and upstream buoyancy transports of the plume. The influence of the Malvinas Current on the Magellan Plume is more dominant north of 50°S, where it increases the along-shelf velocities and generates intrusions of saltier waters from the outer shelf, thus causing a reduction of the downstream buoyancy transport. Our experiments also indicate that the northern limit of the Magellan Plume is set by a high salinity discharge from the San Matias Gulf. Sensitivity experiments show that increments of the wind stress cause a decrease of the downstream buoyancy transport and an increase of the upstream buoyancy transport. Variations of the magnitude of the discharge produce substantial modifications in the downstream penetration of the plume and buoyancy transport. The Magellan discharge generates a northeastward current in the middle shelf, a recirculation gyre south of the inlet and a region of weak currents father north.

NOAA/NWS Storm Prediction Center

Science.gov Websites

Thunderstorm/Tornado Watches Mesoscale Discussions Convective Outlooks Thunderstorm Outlook Fire Weather Analysis Sounding Climatology Upper-Air Maps HREF HRRR Browser SREF SREF Plumes Fire Weather Composite Maps Convective Outlook. Critical fire weather conditions are forecast today. See details... Critical fire weather

Analysis of the correlation between plasma plume and keyhole behavior in laser metal welding for the modeling of the keyhole geometry

NASA Astrophysics Data System (ADS)

Tenner, F.; Brock, C.; Klämpfl, F.; Schmidt, M.

2015-01-01

The process of laser metal welding is widely used in industry. Nevertheless, there is still a lack of complete process understanding and control. For analyzing the process we used two high-speed cameras. Therefore, we could image the plasma plume (which is directly accessible by a camera) and the keyhole (where most of the process instabilities occur) during laser welding isochronously. Applying different image processing steps we were able to find a correlation between those two process characteristics. Additionally we imaged the plasma plume from two directions and were able to calculate a volume with respect to the vaporized material the plasma plume carries. Due to these correlations we are able to conclude the keyhole stability from imaging the plasma plume and vice versa. We used the found correlation between the keyhole behavior and the plasma plume to explain the effect of changing laser power and feed rate on the keyhole geometry. Furthermore, we tried to outline the phenomena which have the biggest effect on the keyhole geometry during changes of feed rate and laser power.

Key factors controlling ozone production in wildfire plumes

NASA Astrophysics Data System (ADS)

Jaffe, D. A.

2017-12-01

Production of ozone in wildfire plumes is complex and highly variable. As a wildfire plume mixes into an urban area, ozone is often, but not always, produced. We have examined multiple factors that can help explain some of this variability. This includes CO/NOy enhancement ratios, photolysis rates, PAN/NOy fraction and degree of NOx oxidation. While fast ozone production is well known, on average, ozone production increases downwind in a plume for several days. Peroxyacetyl nitrate (PAN) is likely a key cause for delayed ozone formation. Recent observations at the Mt. Bachelor Observatory a mountain top observatory relatively remote from nearby anthropogenic influence and in Boise Idaho, an urban setting, show the importance of PAN in wildfire plumes. From these observations we can devise a conceptual model that considers four factors in ozone production: NOx/VOC emission ratio; degree of NOx oxidation; transport time and pathway; and mixing with urban pollutants. Using this conceptual model, we can then devise a lagrangian modeling strategy that can be used to improve our understanding of ozone production in wildfire plumes, both in remote and urban settings.

Translation Optics for 30 cm Ion Engine Thrust Vector Control

NASA Technical Reports Server (NTRS)

Haag, Thomas

2002-01-01

Data were obtained from a 30 cm xenon ion thruster in which the accelerator grid was translated in the radial plane. The thruster was operated at three different throttle power levels, and the accelerator grid was incrementally translated in the X, Y, and azimuthal directions. Plume data was obtained downstream from the thruster using a Faraday probe mounted to a positioning system. Successive probe sweeps revealed variations in the plume direction. Thruster perveance, electron backstreaming limit, accelerator current, and plume deflection angle were taken at each power level, and for each accelerator grid position. Results showed that the thruster plume could easily be deflected up to six degrees without a prohibitive increase in accelerator impingement current. Results were similar in both X and Y direction.

Deciphering the Complex Chemistry of Deep-Ocean Particles Using Complementary Synchrotron X-ray Microscope and Microprobe Instruments.

PubMed

Toner, Brandy M; German, Christopher R; Dick, Gregory J; Breier, John A

2016-01-19

The reactivity and mobility of natural particles in aquatic systems have wide ranging implications for the functioning of Earth surface systems. Particles in the ocean are biologically and chemically reactive, mobile, and complex in composition. The chemical composition of marine particles is thought to be central to understanding processes that convert globally relevant elements, such as C and Fe, among forms with varying bioavailability and mobility in the ocean. The analytical tools needed to measure the complex chemistry of natural particles are the subject of this Account. We describe how a suite of complementary synchrotron radiation instruments with nano- and micrometer focusing, and X-ray absorption spectroscopy (XAS) and X-ray diffraction (XRD) capabilities are changing our understanding of deep-ocean chemistry and life. Submarine venting along mid-ocean ridges creates hydrothermal plumes where dynamic particle-forming reactions occur as vent fluids mix with deep-ocean waters. Whether plumes are net sources or sinks of elements in ocean budgets depends in large part on particle formation, reactivity, and transport properties. Hydrothermal plume particles have been shown to host microbial communities and exhibit complex size distributions, aggregation behavior, and composition. X-ray microscope and microprobe instruments can address particle size and aggregation, but their true strength is in measuring chemical composition. Plume particles comprise a stunning array of inorganic and organic phases, from single-crystal sulfides to poorly ordered nanophases and polymeric organic matrices to microbial cells. X-ray microscopes and X-ray microprobes with elemental imaging, XAS, and XRD capabilities are ideal for investigating these complex materials because they can (1) measure the chemistry of organic and inorganic constituents in complex matrices, usually within the same particle or aggregate, (2) provide strong signal-to-noise data with exceedingly small amounts of material, (3) simplify the chemical complexity of particles or sets of particles with a focused-beam, providing spatial resolution over 6 orders of magnitude (nanometer to millimeter), (4) provide elemental specificity for elements in the soft-, tender-, and hard-X-ray energies, (5) switch rapidly among elements of interest, and (6) function in the presence of water and gases. Synchrotron derived data sets are discussed in the context of important advances in deep-ocean technology, sample handling and preservation, molecular microbiology, and coupled physical-chemical-biological modeling. Particle chemistry, size, and morphology are all important in determining whether particles are reactive with dissolved constituents, provide substrates for microbial respiration and growth, and are delivered to marine sediments or dispersed by deep-ocean currents.

Osmium Isotope Compositions of Komatiite Sources Through Time

NASA Astrophysics Data System (ADS)

Walker, R. J.

2001-12-01

Extending Os isotopic measurements to ancient plume sources may help to constrain how and when the well-documented isotopic heterogeneities in modern systems were created. Komatiites and picrites associated with plume-related volcanism are valuable tracers of the Os isotopic composition of plumes because of their typically high Os concentrations and relatively low Re/Os. Re-Os data are now available for a variety of Phanerozoic, Proterozoic and Archean komatiites and picrites. As with modern plumes, the sources of Archean and Proterozoic komatiites exhibit a large range of initial 187Os/188Os ratios. Most komatiites are dominated by sources with chondritic Os isotopic compositions (e.g. Song La; Norseman-Wiluna; Pyke Hill; Alexo), though some (e.g. Gorgona) derive from heterogeneous sources. Of note, however, two ca. 2.7 Ga systems, Kostomuksha (Russia) and Belingwe (Zimbabwe), have initial ratios enriched by 2-3% relative to the contemporary convecting upper mantle. These results suggest that if the 187Os enrichment was due to the incorporation of minor amounts of recycled crust into the mantle source of the rocks, the crust formed very early in Earth history. Thus, the Os results could reflect derivation of melt from hybrid mantle whose composition was modified by the addition of mafic crustal material that would most likely have formed between 4.2 and 4.5 Ga. Alternately, the mantle sources of these komatiites may have derived a portion of their Os from the putative 187Os - and 186Os -enriched outer core. For this hypothesis to be applicable to Archean rocks, an inner core of sufficient mass would have to have crystallized sufficiently early in Earth history to generate an outer core with 187Os enriched by at least 3% relative to the chondritic average. Using the Pt-Re-Os partition coefficients espoused by our earlier work, and assuming linear growth of the inner core started at 4.5 Ga and continued to present, would yield an outer core at 2.7 Ga with a gamma Os value of only +1.2 and a 186Os/188Os enrichment relative to the contemporary upper mantle of only +13 ppm. Greater isotopic enrichments could have been achieved by 2.7 Ga if either the inner core comprised >2.8% of the mass of the core by 2.7 Ga, or if Re and Os solid metal-liquid metal D's for core crystallization were greater that those applied in the initial calculation.

Geochemistry and jasper beds from the Ordovician Løkken ophiolite, Norway: origin of proximal and distal siliceous exhalites

USGS Publications Warehouse

Grenne, Tor; Slack, John F.

2005-01-01

Stratiform beds of jasper (hematitic chert), composed essentially of SiO2 (69-95 wt %) and Fe2O3 (3-25 wt %), can be traced several kilometers along strike in the Ordovician L??kken ophiolite, Norway. These siliceous beds are closely associated with volcanogenic massive sulfide (VMS) deposits and are interpreted as sea-floor gels that were deposited by fallout from hydrothermal plumes in silica-rich seawater, in which plume-derived Fe oxyhydroxide particles promoted flocculation and rapid settling of large (???200 ??m) colloidal particles of silica-iron oxyhydroxide. Concentrations of chalcophile elements in the jasper beds are at the parts per million level implying that sulfide particle fallout was insignificant and that the Si-Fe gel-forming plumes were mainly derived from intermediate- (100??-250??C) to high-temperature (>250??) white smoker-type vents with high Fe/S ratios. The interpreted setting is similar to that of the Lau basin, where high-temperature (280??-334??C) white smoker venting alternates or overlaps with sulfide mound-forming black smoker venting. Ratios of Al, Sc, Th, Hf, and REE to iron are very low and show that the detrital input was <0.1 percent of the bulk jasper. Most jasper beds are enriched in U, V, P, and Mo relative to the North American Shale Composite, reflecting a predominantly seawater source, whereas REE distribution patterns (positive Eu and negative Ce anomalies) reflect variable mixing of hydrothermal solutions with oxic seawater at dilution ratios of ???102 to 104. Trace element variations in the gel precursor to the jasper are thought to have been controlled by coprecipitation and/or adsorption by Fe oxyhydroxide particles that formed by the oxidation of hydrothermal Fe2+ within the variably seawater-diluted hydrothermal plume(s). Thick jasper layers near the H??ydal VMS orebody show distinct positive As/Fe and Sb/Fe anomalies that are attributed to near-vent rapid settling of Si-Fe particles derived from As- and Sb-rich hydrothermal fluids prior to extensive mixing with seawater in the buoyant plume. Particles that formed later in the highly diluted nonbuoyant plume formed relatively As and Sb poor distal jasper. The large particle sizes and accordingly high settling rates of the particles, together with mass-balance calculations based on modern vent field data, suggest that individual meter-thick jasper beds formed within a plume lifetime of 200 years or less. The lack of thick jasper beds near the L??kken VMS orebody, which is larger than the H??ydal orebody by more than two orders of magnitude, probably reflects a shift to anoxic conditions during L??kken mineralization. This environment limited oxidation of iron in the hydrothermal plume and formation of the ferric oxyhydroxides necessary for the flocculation of silica and sea-floor deposition of the gel precursor of the jasper beds. Distal pyritic and iron-poor cherts are more common than jasper in ancient VMS-hosting sequences. The origin of these other types of siliceous exhalite is enigmatic but at least in some cases involved sulfidation, reduction to magnetite, or dissolution of the original ferric iron in precursor Si-rich gels, either by hydrothermal or diagenetic processes. ?? 2005 Society of Economic Geologists, Inc.

Delineation of a landfill leachate plume using shallow electromagnetic and ground-penetrating radar surveys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nobes, D.C.; Armstrong, M.J.; Broadbent, M.

1994-12-31

Leachate plumes are often more electrically conductive than the surrounding host pore waters, and thus can be detected using shallow electromagnetic (EM) methods. The depth of penetration of ground penetrating radar (GPR) is controlled to a large extent by the electrical conductivity. Conductive leachate plumes will appear as ``blank`` areas in the radar profiles, because the radar energy is more severely attenuated in the region of the leachate plume. The authors present here the results of EM and GPR Surveys carried out in an area adjacent to a landfill site. Previous resistivity surveys indicated the presence of a leachate plumemore » originating from an early stage of the landfill operation. The shallow EM and GPR surveys were carried out, in part, to confirm and refine the resistivity results, and to delineate the spatial extent of the plume. The surficial sediments are coastal sands, and the dune topography has an effect on the EM results, even though the variations in elevation are, in general, no more than 3 m. Besides the leachate plume, numerous conductivity highs and lows are present, which are at least coarsely correlated with topographic lows and highs. Following the empirical procedure outlined by Monier-Williams et al. (1990), the topographic effects have been removed, and the plume is better isolated and delineated. A possible second, weaker leachate plume has been identified, emanating from the current landfill operation. The second plume may follow a channel that was masked by the overlying dune sands. The leading edge of the primary leachate plume is moving to the south-southeast at a rate of 14 to 15 m/yr.« less

Transport of Fine Ash Through the Water Column at Erupting Volcanoes - Monowai Cone, Kermadec-Tonga Arc

NASA Astrophysics Data System (ADS)

Walker, S. L.; Baker, E. T.; Leybourne, M. I.; de Ronde, C. E.; Greene, R.; Faure, K.; Chadwick, W.; Dziak, R. P.; Lupton, J. E.; Lebon, G.

2010-12-01

Monowai cone is a large, active, basaltic stratovolcano, part of the submarine Monowai volcanic center (MVC) located at ~26°S on the Kermadec-Tonga arc. At other actively erupting submarine volcanoes, magma extrusions and hydrothermal vents have been located only near the summit of the edifice, generating plumes enriched with hydrothermal components and magmatic gasses that disperse into the ocean environment at, or shallower than, the summit depth. Plumes found deeper than summit depths are dominated by fresh volcaniclastic ash particles, devoid of hydrothermal tracers, emplaced episodically by down-slope gravity flows, and transport fine ash to 10’s of km from the active eruptions. A water column survey of the MVC in 2004 mapped intensely hydrothermal-magmatic plumes over the shallow (~130 m) summit of Monowai cone and widespread plumes around its flanks. Due to the more complex multiple parasitic cone and caldera structure of MVC, we analyzed the dissolved and particulate components of the flank plumes for evidence of additional sources. Although hydrothermal plumes exist within the adjacent caldera, none of the parasitic cones on Monowai cone or elsewhere within the MVC were hydrothermally or volcanically active. The combination of an intensely enriched summit plume, sulfur particles and bubbles at the sea surface, and ash-dominated flank plumes indicate Monowai cone was actively erupting at the time of the 2004 survey. Monowai cone is thus the fourth erupting submarine volcano we have encountered, and all have had deep ash plumes distributed around their flanks [the others are: Kavachi (Solomon Island arc), NW Rota-1 (Mariana arc) and W Mata (NE Lau basin)]. These deep ash plumes are a syneruptive phenomenon, but it is unknown how they are related to eruptive style and output, or to the cycles of construction and collapse that occur on the slopes of submarine volcanoes. Repeat multibeam bathymetric surveys have documented two large-scale sector collapse events at Monowai and one at NW Rota-1, as well as constructional deposits extending down the flanks of these volcanoes. Acoustic records at Monowai and NW Rota-1 suggest sector collapse events are infrequent while eruptions, and the resulting supply of depositional material, have been nearly continuous. The sector collapse events occurred at times remote from our plume surveys, so, large landslide events are not a prerequisite for the presence of deep ash plumes. Despite a wide range of summit depths (<10 m at Kavachi to 1500 m at W Mata), lava types (basaltic-andesite, boninite, and basalt), and eruptive styles (Surtseyan, Strombolian, and effusive flows with active pillow formation), the deep particle plumes at each of these volcanoes are remarkably similar in their widespread distribution (to 10’s of km from the summit and at multiple depths down the flanks) and composition (dominantly fresh volcanic ash). Moderate eruption rates, lava-seawater interaction and steep slopes below an eruptive vent may be sufficient to initiate the transport of fine ash into the ocean environment and distal sediments via these types of plumes.

Transient Plume Model Testing Using LADEE Spacecraft Attitude Control System Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woronowicz, M. S.

2011-05-20

The Lunar Atmosphere Dust Environment Explorer (LADEE) spacecraft is being designed for a mission featuring low altitude orbits of the Moon to take relevant ambient measurements before that environment becomes altered by future exploration activities. Instruments include a neutral mass spectrometer capable of measuring ambient species density levels below 100 molecules/cm{sup 3}. Coincidentally, with a favorable combination of spacecraft orientations, it is also possible to measure plume gases from LADEE attitude control system thruster operations as they are reflected from the daytime lunar surface and subsequently intercepted by the spacecraft as it orbits overhead. Under such circumstances, it may bemore » possible to test a variety of properties and assumptions associated with various transient plume models or to infer certain aspects regarding lunar surface properties.« less

Transient Plume Model Testing Using LADEE Spacecraft Attitude Control System Operations

NASA Technical Reports Server (NTRS)

Woronowicz, M. S.

2010-01-01

The Lunar Atmosphere Dust Environment Explorer (LADEE) spacecraft is being designed for a mission featuring low altitude orbits of the Moon to take relevant ambient measurements before that environment becomes altered by future exploration activities. Instruments include a neutral mass spectrometer capable of measuring ambient species density levels below 100 molecules/cu cm. Coincidentally, with a favorable combination of spacecraft orientations, it is also possible to measure plume gases from LADEE attitude control system thruster operations as they are reflected from the daytime lunar surface and subsequently intercepted by the spacecraft as it orbits overhead. Under such circumstances, it may be possible to test a variety of properties and assumptions associated with various transient plume models or to infer certain aspects regarding lunar surface properties.

Intercontinental dispersal of bacteria and archaea by transpacific winds

USGS Publications Warehouse

D. Smith,; H. Timonen,; D. Jaffe,; Griffin, Dale W.; M. Birmele,; Perry, K.D.; Ward, P.D.; M. Roberts,

2013-01-01

Microorganisms are abundant in the upper atmosphere, particularly downwind of arid regions, where winds can mobilize large amounts of topsoil and dust. However, the challenge of collecting samples from the upper atmosphere and reliance upon culture-based characterization methods have prevented a comprehensive understanding of globally dispersed airborne microbes. In spring 2011 at the Mt. Bachelor Observatory in North America (2.8 km above sea level), we captured enough microbial biomass in two transpacific air plumes to permit a microarray analysis using 16S rRNA genes. Thousands of distinct bacterial taxa spanning a wide range of phyla and surface environments were detected before, during, and after each Asian long-range transport event. Interestingly, the transpacific plumes delivered higher concentrations of taxa already in the background air (particularly Proteobacteria, Actinobacteria, and Firmicutes). While some bacterial families and a few marine archaea appeared for the first and only time during the plumes, the microbial community compositions were similar, despite the unique transport histories of the air masses. It seems plausible, when coupled with atmospheric modeling and chemical analysis, that microbial biogeography can be used to pinpoint the source of intercontinental dust plumes. Given the degree of richness measured in our study, the overall contribution of Asian aerosols to microbial species in North American air warrants additional investigation.

Intercontinental Dispersal of Bacteria and Archaea by Transpacific Winds

PubMed Central

Timonen, Hilkka J.; Jaffe, Daniel A.; Griffin, Dale W.; Birmele, Michele N.; Perry, Kevin D.; Ward, Peter D.; Roberts, Michael S.

2013-01-01

Microorganisms are abundant in the upper atmosphere, particularly downwind of arid regions, where winds can mobilize large amounts of topsoil and dust. However, the challenge of collecting samples from the upper atmosphere and reliance upon culture-based characterization methods have prevented a comprehensive understanding of globally dispersed airborne microbes. In spring 2011 at the Mt. Bachelor Observatory in North America (2.8 km above sea level), we captured enough microbial biomass in two transpacific air plumes to permit a microarray analysis using 16S rRNA genes. Thousands of distinct bacterial taxa spanning a wide range of phyla and surface environments were detected before, during, and after each Asian long-range transport event. Interestingly, the transpacific plumes delivered higher concentrations of taxa already in the background air (particularly Proteobacteria, Actinobacteria, and Firmicutes). While some bacterial families and a few marine archaea appeared for the first and only time during the plumes, the microbial community compositions were similar, despite the unique transport histories of the air masses. It seems plausible, when coupled with atmospheric modeling and chemical analysis, that microbial biogeography can be used to pinpoint the source of intercontinental dust plumes. Given the degree of richness measured in our study, the overall contribution of Asian aerosols to microbial species in North American air warrants additional investigation. PMID:23220959

Petrography and geochemistry of distal spherules from the K-Pg boundary in the Umbria-Marche region (Italy) and their origin as fractional condensates and melts in the Chicxulub impact plume

NASA Astrophysics Data System (ADS)

Belza, J.; Goderis, S.; Montanari, A.; Vanhaecke, F.; Claeys, P.

2017-04-01

The impact spherules from the distal K-Pg boundary sections are considered to represent silicate droplets condensed and solidified from a laterally expanding, cooling vapor plume formed upon hypervelocity impact. In the present-day Cretaceous-Paleogene boundary (K-Pg) spherule population of the Umbria-Marche region in Italy, three texturally and compositionally distinct types of impact spherules can be identified that are dominantly composed of (1) goethite, (2) K-feldspar or (3) glauconite. Although these phases represent the products of diagenetic alteration, the remnant textural characteristics of the spherules and the type of alteration product are indicative of the spherules' original compositions, which are important to constrain the physicochemical conditions prevalent throughout the impact vapor plume. The presence of relict ghost crystals and the identification of 'iddingsite' indicate that goethite likely represents pseudomorphic replacement after olivine. Goethite spherules contain numerous dendritic, euhedral and skeletal spinel crystals variably dispersed in the groundmass. In terms of textures, five types of goethite spherules can be distinguished, showing striking similarities to chondrules: (I) skeletal, (II) barred, (III) radial/barred, (IV) porphyritic and (V) relict/granular. The morphology of both spinel and olivine (pseudomorphs) is consistent with established formation conditions (peak temperature Tmax, degree of supercooling ΔT, cooling rate, presence of nucleation sites) for different chondrule textural types. As goethite spherules are anomalously enriched in moderately to highly refractory lithophile (Sc, V, Y, Zr, Nb, REE, Hf, Ta, Th) and siderophile (Cr, Co, Ni, W, Ir, Pt) elements, they are interpreted to represent (diagenetically altered) refractory (high-T) condensation products from a well-homogenized plume consisting of both vaporized target and projectile matter. Different from goethite spherules, K-feldspar spherules exhibit pseudomorphic textures after lower-liquidus silicates such as Ca-rich pyroxene and plagioclase. Furthermore, the K-feldspar spherules yield systematically lower abundances of the most refractory trace elements. This suggests that the pre-altered K-feldspar spherules are part of the same fractional condensation sequence of the target-impactor vapor plume, cooled during lateral expansion. Glauconite spherules are cryptocrystalline, exhibiting hemispherical lamellae that resemble the palagonite/smectite alteration layers of basaltic glasses and the K-Pg spherules (microtektites) found at proximal sites around the Gulf of Mexico region. Their trace element contents and REE patterns are strikingly similarity to those of (altered) K-Pg microtektites, suggesting that glauconite spherules represent former glass spherules without crystallites/microlites. Glauconite spherules are interpreted not to be part of the fractional condensation sequence of the impact vapor plume that led to the formation of the replaced goethite and K-felspar spherules. They were likely formed by entrainment of melt, expelled at the steepest angles and highest ejection velocities from the central melt sheet, within the edges of the vapor plume. This work is the first to create a geochemical foundation for vapor plume models, both at the major and trace element scale. In addition, it highlights the unique characteristics of the Chicxulub impact event and emphasizes the importance of its unusual target lithologies. The heterogeneous, layered, and volatile-rich target contributed significantly to the formation of a dust-rich environment, high oxygen fugacities and the preservation of some degree of heterogeneity in the vapor plume. In addition, striking similarities between distal (goethite-type) K-Pg spherules and chondrules may argue for a reevaluation of the impact model as a possible origin for the formation of certain types of cosmic chondrules.

Implications of 187Os isotopic heterogeneities in a mantle plume: evidence from Gorgona Island and Curaçao

NASA Astrophysics Data System (ADS)

Walker, Richard J.; Storey, Michael; Kerr, Andrew C.; Tarney, John; Arndt, Nicholas T.

1999-03-01

Recent work has suggested that the mafic-ultramafic volcanism in evidence throughout portions of the Caribbean, Central America, and northern South America, including the islands of Gorgona and Curaçao, was generated as part of a middle-Cretaceous, large igneous province. New Re-Os isochron results for tholeiitic basalts from Gorgona and Curaçao indicate crystallization ages of 89.2 ± 5.2 and 85.6 ± 8.1 Ma, respectively, consistent with reported Ar ages. The Gorgona ultramafic suite shows a large range in initial Os isotopic composition, with γ Os values ranging from -0.5 to +12.4. This large range reflects isotopic heterogeneities in the mantle source similar to those observed for modern ocean island basalts. In contrast to ocean island basalts, however, Os isotopic compositions do not correlate with variations in Nd, Sr, or Pb isotopic compositions, which are within the range of depleted mid-ocean ridge basalts. The processes that produced these rocks evidently resulted in the decoupling of Os isotopes from the Nd, Sr, and Pb isotopic systems. Picrites from Curaçao have very uniform, chondritic initial Os isotopic compositions, with initial γ Os values ranging only from -0.4 to ±1.4. Basalts from Curaçao, however, define an isochron with a 187Os-enriched initial isotopic composition (γ Os = +9.5). In contrast to the 187Os-enriched ultramafic rocks from Gorgona, the enrichment in these basalts could have resulted from lithospheric contamination. If the Gorgona and Curaçao rocks were derived from the same plume, Os results, combined with Sr, Nd, and Pb data indicate a heterogeneous plume, with multiple compositionally and isotopically distinct domains. The Os isotopic results require derivation of Os from a minimum of two distinct reservoirs, one with a composition very similar to the chondritic average and one with long-term enriched Re/Os. Oceanic crustal recycling has been invoked to explain most of the 187Os enrichments that have been observed in ocean island basalt sources and could potentially apply to the Gorgona suite. Crustal recycling, however, requires large proportions of very ancient recycled basaltic crust in the sources of the 187Os-enriched ultramafic rocks to explain the magnitude of 187Os enrichments observed. For example, addition of 20% oceanic crust to fertile mantle, and nearly 3 billion years are necessary to generate a reservoir with the Os isotopic composition of the most radiogenic komatiites. If the recycled oceanic crust was added to basalt-depleted mantle, as may be indicated by ɛ Nd values for the komatiites averaging about +10, even larger proportions of older crust are required. Large proportions of oceanic mafic crust in the sources of the 187Os-enriched komatiites, although petrologically conceivable under certain melting conditions, is unlikely here given the limited trace element and lithophile isotope system variations. These results raise questions about the efficacy of using Os isotopes to constrain the proportion of recycled oceanic crust in other plumes. Other possible mechanisms for generating 187Os-enriched mantle include invoking the existence of a 187Os-enriched lower mantle, and minor outer core-lower mantle interactions.

Numerical study on the influence of aluminum on infrared radiation signature of exhaust plume

NASA Astrophysics Data System (ADS)

Zhang, Wei; Ye, Qing-qing; Li, Shi-peng; Wang, Ning-fei

2013-09-01

The infrared radiation signature of exhaust plume from solid propellant rockets has been widely mentioned for its important realistic meaning. The content of aluminum powder in the propellants is a key factor that affects the infrared radiation signature of the plume. The related studies are mostly on the conical nozzles. In this paper, the influence of aluminum on the flow field of plume, temperature distribution, and the infrared radiation characteristics were numerically studied with an object of 3D quadrate nozzle. Firstly, the gas phase flow field and gas-solid multi phase flow filed of the exhaust plume were calculated using CFD method. The result indicates that the Al203 particles have significant effect on the flow field of plume. Secondly, the radiation transfer equation was solved by using a discrete coordinate method. The spectral radiation intensity from 1000-2400 cm-1 was obtained. To study the infrared radiation characteristics of exhaust plume, an exceptional quadrate nozzle was employed and much attention was paid to the influences of Al203 particles in solid propellants. The results could dedicate the design of the divert control motor in such hypervelocity interceptors or missiles, or be of certain meaning to the improvement of ingredients of solid propellants.

Where the oil from surface and subsurface plumes deposited during/after Deepwater Horizon oil spill?

NASA Astrophysics Data System (ADS)

Yan, B.

2016-02-01

The Deepwater Horizon (DwH) oil spill released an estimated 4.9 million barrels (about 200 million gallons) of crude oil into the Gulf of Mexico between April 20, 2010 and July 15, 2010. Though Valentine et al. has linked the elevated oil components in some sediments with the subsurface plume, the sites with fallout from the ocean surface plume has not been identified. This piece of information is critical not only for a comprehensive scientific understanding of the ecosystem response and fate of spill-related pollutants, but also for litigation purposes and future spill response and restoration planning. In this study we focus on testing the hypothesis that marine snow from the surface plume were deposited on the sea floor over a broad area. To do so, we use publicly available data generated as part of the ongoing Natural Resource Damage Assessment (NRDA) process to assess the spatial distribution of petroleum hydrocarbons in the water column and deep-ocean sediments of the Gulf of Mexico. Sensitive hydrocarbon markers are used to differentiate hydrocarbons from surface plume, deep subsurface plume, and in-situ burning. Preliminary results suggest the overlapping but different falling sites of these plumes and the sedimentation process was controlled by various biological, chemical, and physical factors.

Ridge suction drives plume-ridge interactions

NASA Astrophysics Data System (ADS)

Niu, Y.; Hékinian, R.

2003-04-01

Deep-sourced mantle plumes, if existing, are genetically independent of plate tectonics. When the ascending plumes approach lithospheric plates, interactions between the two occur. Such interactions are most prominent near ocean ridges where the lithosphere is thin and the effect of plumes is best revealed. While ocean ridges are mostly passive features in terms of plate tectonics, they play an active role in the context of plume-ridge interactions. This active role is a ridge suction force that drives asthenospheric mantle flow towards ridges because of material needs to form the ocean crust at ridges and lithospheric mantle in the vicinity of ridges. This ridge suction force increases with increasing plate separation rate because of increased material demand per unit time. As the seismic low-velocity zone atop the asthenosphere has the lowest viscosity that increases rapidly with depth, the ridge-ward asthenospheric flow is largely horizontal beneath the lithosphere. Recognizing that plume materials have two components with easily-melted dikes/veins enriched in volatiles and incompatible elements dispersed in the more refractory and depleted peridotitic matrix, geochemistry of some seafloor volcanics well illustrates that plume-ridge interactions are consequences of ridge-suction-driven flow of plume materials, which melt by decompression because of lithospheric thinning towards ridges. There are excellent examples: 1. The decreasing La/Sm and increasing MgO and CaO/Al_2O_3 in Easter Seamount lavas from Salas-y-Gomez Islands to the Easter Microplate East rift zone result from progressive decompression melting of ridge-ward flowing plume materials. 2. The similar geochemical observations in lavas along the Foundation hotline towards the Pacific-Antarctic Ridge result from the same process. 3. The increasing ridge suction force with increasing spreading rate explains why the Iceland plume has asymmetric effects on its neighboring ridges: both topographic and geochemical anomalies extend < 400 km along the slower (20 to 13 mm/yr northward) spreading South Kolbeinsey Ridge, but > 1500 km along the faster (20 to 25 mm/yr southward) spreading Reykjanes Ridge. 4. The spreading-rate dependent ridge suction force also explains the first-order differences between the fast-spreading East Pacific Rise (EPR) and the slow-spreading Mid-Atlantic Ridge (MAR). Identified mantle plumes/hotspots are abundant near the MAR (e.g., Iceland, Azores, Ascension, Tristan, Gough, Shona and Bouvet), but rare along the entire EPR (notably, the Easter hotspot at ˜27^oS on the Nazca plate). Such apparent unequal hotspot distribution would allow a prediction of more enriched MORB at the MAR than at the EPR. However, the mean compositions between MAR-MORB and EPR-MORB are the same in terms of incompatible element abundances, and are identical in terms of Sr-Nd-Pb isotopic ratios. This suggests similar extents of mantle plume contributions to EPR and MAR MORB. We consider that the apparent rarity of near-EPR plumes/hotspots results from fast spreading. The fast spreading creates large ridge suction forces that do not allow the development of surface expressions of mantle plumes as such, but draw plume materials to a broad zone of sub-ridge upwelling, giving rise to random distribution of abundant enriched MORB and elevated and smooth axial topography along the EPR (vs. MAR). One of the important implications is that the asthenospheric flow is necessarily decoupled from its overlaying oceanic lithospheric plate. This decoupling increases with increasing spreading rate.

Geochemical structure of the Hawaiian plume: Sr, Nd, and Os isotopes in the 2.8 km HSDP-2 section of Mauna Kea volcano

NASA Astrophysics Data System (ADS)

Bryce, Julia G.; Depaolo, Donald J.; Lassiter, John C.

2005-09-01

Sr, Nd, and Os isotopic measurements were made on 110 Mauna Kea lava and hyaloclastite samples from the drillcore retrieved from the second phase of the Hawaii Scientific Drilling Project (HSDP-2). The samples come from depths of 255 to 3098 meters below sea level, span an age range from 200 to about 550-600 kyr, and represent an ordered record of the lava output from Mauna Kea volcano as it drifted a distance of about 40 km over the magma-producing region of the Hawaiian hot spot. The deepest (oldest) samples represent the time when Mauna Kea was closest to the center of the melting region of the Hawaiian plume. The Sr and Os isotopic ratios in HSDP-2 lavas show only subtle isotopic shifts over the ˜400 kyr history represented by the core. Neodymium isotopes (ɛNd values) increase systematically with decreasing age from an average value of nearly +6.5 to an average value of +7.5. This small change corresponds to subtle shifts in 87Sr/86Sr and 187Os/188Os isotope ratios, with small shifts of ɛHf, a large shift in 208Pb/204Pb and 208Pb/207Pb values, and with a very large shift in He isotope ratios from R/RA values of about 7-8 to values as high as 25. When Mauna Kea was closest to the plume core, the magma source did not have primitive characteristics for Nd, Sr, Pb, Hf, and Os isotopes but did have variable amounts of "primitive" helium. The systematic shifts in Nd, Hf, Pb, and He isotopes are consistent with radial isotopic zoning within the melting region of the plume. The melting region constitutes only the innermost, highest-temperature part of the thermally anomalous plume mantle. The different ranges of values observed for each isotopic system, and comparison of Mauna Kea lavas with those of Mauna Loa, suggest that the axial region of the plume, which has a radius of ˜20 km, is a mixture of recycled subducted components and primitive lower mantle materials, recently combined during the formational stages of the plume at the base of the mantle. The proportions of recycled and primitive components are not constant, and this requires there be longitudinal (vertical) heterogeneity within the core of the plume. The remainder of the plume, outside this plume "core zone," is less heterogeneous but distinct from upper mantle as represented by mid-ocean ridge basalt (MORB). The plume structure may provide a detailed view of mantle isotopic composition near the core-mantle boundary.

Monitoring Eruptive Activity at Mount St. Helens with TIR Image Data

NASA Technical Reports Server (NTRS)

Vaughan, R. G.; Hook, S. J.; Ramsey, M. S.; Realmuto, V. J.; Schneider, D. J.

2005-01-01

Thermal infrared (TIR) data from the MASTER airborne imaging spectrometer were acquired over Mount St. Helens in Sept and Oct, 2004, before and after the onset of recent eruptive activity. Pre-eruption data showed no measurable increase in surface temperatures before the first phreatic eruption on Oct 1. MASTER data acquired during the initial eruptive episode on Oct 14 showed maximum temperatures of similar to approximately 330 C and TIR data acquired concurrently from a Forward Looking Infrared (FLIR) camera showed maximum temperatures similar to approximately 675 C, in narrow (approximately 1-m) fractures of molten rock on a new resurgent dome. MASTER and FLIR thermal flux calculations indicated a radiative cooling rate of approximately 714 J/m(exp 2)/s over the new dome, corresponding to a radiant power of approximately 24 MW. MASTER data indicated the new dome was dacitic in composition, and digital elevation data derived from LIDAR acquired concurrently with MASTER showed that the dome growth correlated with the areas of elevated temperatures. Low SO2 concentrations in the plume combined with sub-optimal viewing conditions prohibited quantitative measurement of plume SO2. The results demonstrate that airborne TIR data can provide information on the temperature of both the surface and plume and the composition of new lava during eruptive episodes. Given sufficient resources, the airborne instrumentation could be deployed rapidly to a newly-awakening volcano and provide a means for remote volcano monitoring.

Geochemical characteristics of the La Réunion mantle plume source inferred from olivine-hosted melt inclusions from the adventive cones of Piton de la Fournaise volcano (La Réunion Island)

NASA Astrophysics Data System (ADS)

Valer, Marina; Schiano, Pierre; Bachèlery, Patrick

2017-09-01

Major and trace element compositions were obtained for bulk rocks and melt inclusions hosted in olivine crystals (Fo > 85) from the adventive cones of the Piton de La Fournaise volcano (La Réunion Island). Ratios of highly incompatible trace elements for these magmas are used to identify the nature of the La Réunion mantle plume source. Although adventive cone lavas display unusual major element compositions compared to the historical lavas of the volcano (e.g., lower CaO/Al2O3), trace element data suggest that the magmas emitted by the adventive cones originate from a common chemical source. This source may correspond to either a homogeneous mixed source of different mantle components or a near-primitive less-differentiated mantle source. The melt inclusions display ratios of highly incompatible elements (e.g., Th/La, Nb/La) which are similar to primitive mantle values, and lower Nb/U ratios compared to most oceanic basalts. These results and previous isotopic and trace element data suggest that La Réunion plume samples a source which is intermediate between a primitive-like mantle domain and a slightly depleted one almost unaffected by the recycling processes. This source could have originated from early depletion of the primitive mantle. Assuming a depletion 4.45 Gyr ago, 10% melting of this slightly depleted source could explain the enriched trace element concentrations of the melt inclusions.

Jupiter-Io Montage

NASA Technical Reports Server (NTRS)

2007-01-01

This is a montage of New Horizons images of Jupiter and its volcanic moon Io, taken during the spacecraft's Jupiter flyby in early 2007. The Jupiter image is an infrared color composite taken by the spacecraft's near-infrared imaging spectrometer, the Linear Etalon Imaging Spectral Array (LEISA) at 1:40 UT on Feb. 28, 2007. The infrared wavelengths used (red: 1.59 um, green: 1.94 um, blue: 1.85 um) highlight variations in the altitude of the Jovian cloud tops, with blue denoting high-altitude clouds and hazes, and red indicating deeper clouds. The prominent bluish-white oval is the Great Red Spot. The observation was made at a solar phase angle of 75 degrees but has been projected onto a crescent to remove distortion caused by Jupiter's rotation during the scan. The Io image, taken at 00:25 UT on March 1st 2007, is an approximately true-color composite taken by the panchromatic Long-Range Reconnaissance Imager (LORRI), with color information provided by the 0.5 um ('blue') and 0.9 um ('methane') channels of the Multispectral Visible Imaging Camera (MVIC). The image shows a major eruption in progress on Io's night side, at the northern volcano Tvashtar. Incandescent lava glows red beneath a 330-kilometer high volcanic plume, whose uppermost portions are illuminated by sunlight. The plume appears blue due to scattering of light by small particles in the plume

This montage appears on the cover of the Oct. 12, 2007, issue of Science magazine.

Simulating Bubble Plumes from Breaking Waves with a Forced-Air Venturi

NASA Astrophysics Data System (ADS)

Long, M. S.; Keene, W. C.; Maben, J. R.; Chang, R. Y. W.; Duplessis, P.; Kieber, D. J.; Beaupre, S. R.; Frossard, A. A.; Kinsey, J. D.; Zhu, Y.; Lu, X.; Bisgrove, J.

2017-12-01

It has been hypothesized that the size distribution of bubbles in subsurface seawater is a major factor that modulates the corresponding size distribution of primary marine aerosol (PMA) generated when those bubbles burst at the air-water interface. A primary physical control of the bubble size distribution produced by wave breaking is the associated turbulence that disintegrates larger bubbles into smaller ones. This leads to two characteristic features of bubble size distributions: (1) the Hinze scale which reflects a bubble size above which disintegration is possible based on turbulence intensity and (2) the slopes of log-linear regressions of the size distribution on either side of the Hinze scale that indicate the state of plume evolution or age. A Venturi with tunable seawater and forced air flow rates was designed and deployed in an artificial PMA generator to produce bubble plumes representative of breaking waves. This approach provides direct control of turbulence intensity and, thus, the resulting bubble size distribution characterizable by observations of the Hinze scale and the simulated plume age over a range of known air detrainment rates. Evaluation of performance in different seawater types over the western North Atlantic demonstrated that the Venturi produced bubble plumes with parameter values that bracket the range of those observed in laboratory and field experiments. Specifically, the seawater flow rate modulated the value of the Hinze scale while the forced-air flow rate modulated the plume age parameters. Results indicate that the size distribution of sub-surface bubbles within the generator did not significantly modulate the corresponding number size distribution of PMA produced via bubble bursting.

Observations of thermal ion influxes about the space shuttle

NASA Technical Reports Server (NTRS)

Grebowsky, Joe M.; Schaefer, A.

1990-01-01

Ion mass spectrometer measurements made as part of the University of Iowa's Plasma Diagnostic Package on the STS-3 and Spacelab 2 Space Shuttle missions sampled a variety of ion composition and collected ion current responses to gas emissions from the vehicle. The only other shuttle ion measurements were made by an Air Force Geophysics Laboratory (AFGL) quadrupole spectrometer flown on STS-4. Gas emissions change the distribution of the incoming plasma through scattering and charge transfer processes. A background flux of contaminant ion species (mostly relating to water) always exists in the near vicinity of the shuttle with a magnitude which is dependent on the look direction of the spectrometer but which varies differently with changes in the angle of attack than that of the ambient ions. There is a near shuttle wake cavity in the contaminant ion distributions which has a different spatial configuration than the wake of the ambient ions. Although water dumps produce the most persistent ion perturbations, the sources for ion current modification were best delineated from measurements made when only one or two of the Reaction Control System thrusters fired for a relatively long duration. Contaminant ion perturbations associated with such firings were observed to persist for the order of a second after the cessation of the firings. The dense thruster plumes are efficient collisional, charge exchange barriers to the passage of ambient ions. Collected ion current perturbations were more evident for firings of the rear verniers, whose plumes scatter off projecting surfaces, than for the nose thrusters. The effect of the Vernier firings was found to depend not only on the location and attitude of the spectrometer with respect to the shuttle and thruster plume direction, but also on the orientation of the local magnetic field with respect to the shuttle velocity.

Mantle and crustal contributions to continental flood volcanism

USGS Publications Warehouse

Arndt, N.T.; Czamanske, G.K.; Wooden, J.L.; Fedorenko, V.A.

1993-01-01

Arndt, N.T., Czamanske, G.K., Wooden, J.L. and Fedorenko, V.A., 1993. Mantle and crustal contributions to continental flood volcanism. In: M.J.R. Wortel, U. Hansen and R. Sabadini (Editors), Relationships between Mantle Processes and Geological Processes at or near the Earth's Surface. Tectonophysics, 223: 39-52. Most continental flood basalts are enriched in incompatible elements and have high initial 87Sr/86Sr ratios and low ??{lunate}Nd values. Many are depleted in Nb and Ta. The commonly-held view that these characteristics are inherited directly from a source in metasomatized lithospheric mantle is inconsistent with the following arguments: (1) thermomechanical modelling demonstrates that flood basalt magmas come mainly from an asthenospheric or plume source, with minimal direct melting of the continental lithospheric mantle. The low water contents of most flood basalts argue against proposals that hydrous lithosphere was the source. (2) Lithospheric mantle normally has low concentrations of incompatible elements, and chondrite-normalized Nb and Ta contents similar to those of other incompatible elements. Such material cannot be the unmodified source of Nb-Ta-depleted basalts such as those from the Karoo, Ferrar, or Columbia River provinces. We suggest there are two main controls on the compositions of continental flood basalts. The first is lithospheric thickness, which strongly influences the depth and degree of mantle melting of a plume or asthenospheric source, and thus has an important influence on the composition of primary magmas. All liquids formed by partial melting of peridotite at sub-lithosphere depths are highly magnesian (20-25 wt.% MgO) but have variable trace-element contents. Where the lithosphere is thick, the source melts at high pressure, garnet is present, the degree of melting is low, and trace-element concentrations are high. This type of magma evolves to produce the high-Ti type of continental flood basalt. Where the lithosphere is thinner, the source ascends to shallower levels, the degree of melting is greater, garnet may be exhausted, and the magmas have lower trace-element contents; these magmas yield low-Ti basalts. The second control is processing of magmas in chambers that were periodically replenished and tapped, while continuously fractionating and assimilating their wall rocks. The uniform compositions of basalts that evolve in such chambers are far removed from those of their picritic parental magmas. Major elements in continental flood basalts reflect control by olivine, pyroxene, and plagioclase crystallization, and this assemblage places the magma chambers at crustal depth. We believe that trace-element and isotopic compositions are also buffered, and that the erupted basalts represent steady-state liquids tapped from these magma chambers. These processes impose a crustal signature on the magmas, as expressed most strongly in the concentrations of incompatible elements (e.g., Nb-Ta anomalies) and their isotopic characteristics. ?? 1993.

Lévy-taxis: a novel search strategy for finding odor plumes in turbulent flow-dominated environments

NASA Astrophysics Data System (ADS)

Pasternak, Zohar; Bartumeus, Frederic; Grasso, Frank W.

2009-10-01

Locating chemical plumes in aquatic or terrestrial environments is important for many economic, conservation, security and health related human activities. The localization process is composed mainly of two phases: finding the chemical plume and then tracking it to its source. Plume tracking has been the subject of considerable study whereas plume finding has received little attention. We address here the latter issue, where the searching agent must find the plume in a region often many times larger than the plume and devoid of the relevant chemical cues. The probability of detecting the plume not only depends on the movements of the searching agent but also on the fluid mechanical regime, shaping plume intermittency in space and time; this is a basic, general problem when exploring for ephemeral resources (e.g. moving and/or concealing targets). Here we present a bio-inspired search strategy named Lévy-taxis that, under certain conditions, located odor plumes significantly faster and with a better success rate than other search strategies such as Lévy walks (LW), correlated random walks (CRW) and systematic zig-zag. These results are based on computer simulations which contain, for the first time ever, digitalized real-world water flow and chemical plume instead of their theoretical model approximations. Combining elements of LW and CRW, Lévy-taxis is particularly efficient for searching in flow-dominated environments: it adaptively controls the stochastic search pattern using environmental information (i.e. flow) that is available throughout the course of the search and shows correlation with the source providing the cues. This strategy finds natural application in real-world search missions, both by humans and autonomous robots, since it accomodates the stochastic nature of chemical mixing in turbulent flows. In addition, it may prove useful in the field of behavioral ecology, explaining and predicting the movement patterns of various animals searching for food or mates.

The effects of 1 kW class arcjet thruster plumes on spacecraft charging and spacecraft thermal control materials

NASA Technical Reports Server (NTRS)

Bogorad, A.; Lichtin, D. A.; Bowman, C.; Armenti, J.; Pencil, E.; Sarmiento, C.

1992-01-01

Arcjet thrusters are soon to be used for north/south stationkeeping on commercial communications satellites. A series of tests was performed to evaluate the possible effects of these thrusters on spacecraft charging and the degradation of thermal control material. During the tests the interaction between arcjet plumes and both charged and uncharged surfaces did not cause any significant material degradation. In addition, firing an arcjet thruster benignly reduced the potential of charged surfaces to near zero.

Microbiology, Redox and Contaminat Fate in the Grindsted Landfill Leachate Plume - A Summary of 25 Years of work

NASA Astrophysics Data System (ADS)

Christensen, T. H.

2001-05-01

The contamination by leachate of the upper aquifer at the Grindsted Landfill (Denmark) stretches about 300 m downgradient from the landfill. The plume has been described with respect to water chemistry, sediment chemistry, pollutant distribution, microbial counts, PLFA and redox rates determined by unamended bioassays. This presentation summaries the findings and discusses unanswered questions. The landfill was active from 1930 to the mid 1970 and has no engineered leachate collection system. Leachate from municipal as well as from industrial waste has entered the aquifer for more than thirty years. The redox conditions change from strongly anaerobic (methanogenic, sulfate reducing, iron reducing) close to the landfill over manganese reduction and denitrification to aerobic conditions in the outskirts of the plume The redox conditions were determined from groundwater sample composition, hydrogen concentrations and sediment chemistry. The plume showed strong attenuation of aromatic compounds within the first 100 m downgradient of the landfill. Degradation experiments (batch, in-situ testers, long term field injection experiments) could not fully document degradation of all the compounds. MPN-measurements of methanogens, sulfate-reducers, iron-reducers, manganese-reducers and denitrifiers showed abundance of all groups with a slight trend with the redox conditions. PLFA measurements did not provide much insight into the microbial populations of the plume, but confirmed some previous observations. Bioassays gave estimates of the rates of the various redox processes, but showed for some samples more simultaneous redox processes. More than 25 years of work has been put into the Grindsted Landfill leachate plume. References Bjerg, P.L., Rugge, K., Cortsen, J., Nielsen, P.H. & Christensen, T.H. (1999): Degradation of aromatic and chlorinated aliphatic hydrocarbons in the anaerobic part of the Grindsted Landfill leachate plume: In situ microcosm and laboratory batch experiments. Ground Water, 37, 113-121. Bjerg, P.L., Rugge, K., Pedersen, J.K. & Christensen, T.H. (1995): Distribution of redox sensitive groundwater quality parameters downgradient of a landfill (Grindsted, Denmark). Environmental Science and Technology, 29, 1387-1394. Heron, G., Bjerg, P.L., Gravesen, P., Ludvigsen, L. & Christensen, T.H. (1998): Geology and sediment geochemistry of a landfill leachate contaminated aquifer (Grindsted, Denmark). Journal of Contaminant Hydrology, 29, 301-317. Jakobsen, R., Albrechtsen, H.-J., Rasmussen, M., Bay, H., Bjerg, P.L. & Christensen, T.H. (1998): H2 concentrations in a landfill leachate plume (Grindsted, Denmark): In situ energetics of terminal electron acceptor processes. Environmental Science and Technology, 32, 2142-2148. Ludvigsen, L., Albrechtsen, H.-J., Heron, G., Bjerg, P.L. & Christensen, T.H. (1998): Anaerobic microbial redox processes in a landfill leachate contaminated aquifer (Grindsted, Denmark). Journal of Contaminant Hydrology, 33, 273-291. Ludvigsen, L., Albrechtsen, H.-J., Ringelberg, D., Ekelund, F. & Christensen, T.H. (1999): Distribution and composition of microbial populations in a landfill leachate contaminated aquifer (Grindsted, Denmark). Microbial Ecology, 37, (3), 197-207. Rugge, K., Bjerg, P.L. & Christensen, T.H. (1995): Distribution of organic compounds from municipal solid waste in the groundwater downgradient of a landfill (Grindsted, Denmark). Environmental Science and Technology, 29, 1395-1400.

Biomass burning emissions of trace gases and particles in marine air at Cape Grim, Tasmania, 41° S

NASA Astrophysics Data System (ADS)

Lawson, S. J.; Keywood, M. D.; Galbally, I. E.; Gras, J. L.; Cainey, J. M.; Cope, M. E.; Krummel, P. B.; Fraser, P. J.; Steele, L. P.; Bentley, S. T.; Meyer, C. P.; Ristovski, Z.; Goldstein, A. H.

2015-07-01

Biomass burning (BB) plumes were measured at the Cape Grim Baseline Air Pollution Station during the 2006 Precursors to Particles campaign, when emissions from a fire on nearby Robbins Island impacted the station. Measurements made included non methane organic compounds (NMOCs) (PTR-MS), particle number size distribution, condensation nuclei (CN) > 3 nm, black carbon (BC) concentration, cloud condensation nuclei (CCN) number, ozone (O3), methane (CH4), carbon monixide (CO), hydrogen (H2), carbon dioxide (CO2), nitrous oxide (N2O), halocarbons and meteorology. During the first plume strike event (BB1), a four hour enhancement of CO (max ~ 2100 ppb), BC (~ 1400 ng m-3) and particles > 3 nm (~ 13 000 cm-3) with dominant particle mode of 120 nm were observed overnight. Dilution of the plume resulted in a drop in the dominant particle mode to 50 nm, and then growth to 80 nm over 5 h. This was accompanied by an increase in O3, suggesting that photochemical processing of air and condensation of low volatility oxidation products may be driving particle growth. The ability of particles > 80 nm (CN80) to act as CCN at 0.5 % supersaturation was investigated. The ΔCCN / ΔCN80 ratio was lowest during the fresh BB plume (56 %), higher during the particle growth event (77 %) and higher still (104 %) in background marine air. Particle size distributions indicate that changes to particle chemical composition, rather than particle size, are driving these changes. Hourly average CCN during both BB events were between 2000-5000 CCN cm-3, which were enhanced above typical background levels by a factor of 6-34, highlighting the dramatic impact BB plumes can have on CCN number in clean marine regions. During the 29 h of the second plume strike event (BB2) CO, BC and a range of NMOCs including acetonitrile and hydrogen cyanide (HCN) were clearly enhanced and some enhancements in O3 were observed (ΔO3 / ΔCO 0.001-0.074). A shortlived increase in NMOCs by a factor of 10 corresponded with a large CO enhancement, an increase of the NMOC / CO emission ratio (ER) by a factor of 2-4 and a halving of the BC / CO ratio. Rainfall on Robbins Island was observed by radar during this period which likely resulted in a lower fire combustion efficiency, and higher emission of compounds associated with smouldering. This highlights the importance of relatively minor meterological events on BB emissions. Emission factors (EF) were derived for a range of trace gases, some never before reported for Australian conditions, (including hydrogen, phenol and toluene) using a calculated ER to CO and a published CO EF. The EF derived for most species are comparable to other temperate Australian studies but lower than Northern Hemisphere temperate studies. This work demonstrates the substantial impact that BB plumes have on the composition of marine air, and the significant changes that can occur as the plume is diluted and interacts with other emission sources. We also provide new trace gas and particle EF for temperate southern Australia.

Contamination control and plume assessment of low-energy thrusters

NASA Technical Reports Server (NTRS)

Scialdone, John J.

1993-01-01

Potential contamination of a spacecraft cryogenic surface by a xenon (Xe) ion generator was evaluated. The analysis involves the description of the plume exhausted from the generator with its relative component fluxes on the spacecraft surfaces, and verification of the conditions for condensation, adsorption, and sputtering at those locations. The data describing the plume fluxes and their effects on surfaces were obtained from two sources: the tests carried out with the Xe generator in a small vacuum chamber to indicate deposits and sputter on monitor slides; and the extensive tests with a mercury (Hg) ion thruster in a large vacuum chamber. The Hg thruster tests provided data on the neutrals, on low-energy ion fluxes, on high-energy ion fluxes, and on sputtered materials at several locations within the plume.

Potential Applications of JNPP to Infrared-Based Remote Sensing of Volcanic Emissions

NASA Astrophysics Data System (ADS)

Realmuto, V. J.

2016-12-01

The simultaneous collection of VIIRS, CrIS, and OMPS data will make JNPP an ideal platform for monitoring volcanic emissions. For daytime overpasses we will obtain three contemporaneous, but independent, estimates of SO2 column density, as well as information on the quantity and composition of aerosols and volcanic ash. We will use the independent measurements to validate individual retrieval techniques, and exploit the synergy between UV and TIR remote sensing. The finer spatial resolution of VIIRS (750 m at nadir), relative to OMPS (50 km) and CrIS (14 km), will allow us to characterize variations in surface conditions, plume composition, and the distribution of clouds within an IFOV of CrIS or OMPS, and assess the impact of these variations on the SO2retrievals. Atmospheric profiles are an essential input to the retrieval procedures, and the profiles derived from CrIS soundings will provide us with an accurate description of atmospheric conditions local to the plumes. In addition, the fine spectral resolution of CrIS will enable us to identify and quantify the components of heterogeneous (gas + particulate) plumes. We will demonstrate the potential use of JPSS to map volcanic planes through the analyses of TIR data acquired by EOS (ASTER, MODIS, and AIRS) and SNPP (VIIRS and CrIS) instruments over the plumes generated by recent eruptions of Eyjafallajökull, Bardarbunga (Iceland), Calbuco (Chile), and Ontake (Japan) Volcanoes. We will present comparisons of the TIR-based retrievals to OMI and SNPP-OMPS data products. Finally, we will outline a path to operations through collaboration with the Alaska Volcano Observatory (USGS), Anchorage Volcanic Ash Advisory Center (NWS + FAA), NASA-GSFC Direct Readout Lab, and University of Alaska-Fairbanks. This research was conducted at the Jet Propulsion Laboratory, California Institute of Technology, under contract to National Atmospheric and Space Administration.

Retrieval of volcanic ash properties from the Infrared Atmospheric Sounding Interferometer (IASI)

NASA Astrophysics Data System (ADS)

Ventress, Lucy; Carboni, Elisa; Smith, Andrew; Grainger, Don; Dudhia, Anu; Hayer, Catherine

2014-05-01

The Infrared Atmospheric Sounding Interferometer (IASI), on board both the MetOp-A and MetOp-B platforms, is a Fourier transform spectrometer covering the mid-infrared (IR) from 645-2760cm-1 (3.62-15.5 μm) with a spectral resolution of 0.5cm-1 (apodised) and a pixel diameter at nadir of 12km. These characteristics allow global coverage to be achieved twice daily for each instrument and make IASI a very useful tool for the observation of larger aerosol particles (such as desert dust and volcanic ash) and the tracking of volcanic plumes. In recent years, following the eruption of Eyjafjallajökull, interest in the the ability to detect and characterise volcanic ash plumes has peaked due to the hazards to aviation. The thermal infrared spectra shows a rapid variation with wavelength due to absorption lines from atmospheric and volcanic gases as well as broad scale features principally due to particulate absorption. The ash signature depends upon both the composition and size distribution of ash particles as well as the altitude of the volcanic plume. To retrieve ash properties, IASI brightness temperature spectra are analysed using an optimal estimation retrieval scheme and a forward model based on RTTOV. Initially, IASI pixels are flagged for the presence of volcanic ash using a linear retrieval detection method based on departures from a background state. Given a positive ash signal, the RTTOV output for a clean atmosphere (containing atmospheric gases but no cloud or aerosol/ash) is combined with an ash/cloud layer using the same scheme as for the Oxford-RAL Retrieval of Aerosol and Cloud (ORAC) algorithm. The retrieved parameters are ash optical depth (at a reference wavelength of 550nm), ash effective radius, layer altitude and surface temperature. The potential for distinguishing between different ash types is explored and a sensitivity study of the retrieval algorithm is presented. Results are shown from studies of the evolution and composition of ash plumes for recent volcanic eruptions.

Mantle Plumes and Geologically Recent Volcanism on Mars

NASA Astrophysics Data System (ADS)

Kiefer, W. S.

2013-12-01

Despite its small size, Mars has remained volcanically active until the geologically recent past. Crater retention ages on the volcanos Arsia Mon, Olympus Mons, and Pavonis Mons indicate significant volcanic activity in the last 100-200 million years. The radiometric ages of many shergottites, a type of igneous martian meteorite, indicate igneous activity at about 180 million years ago. These ages correspond to the most recent 2-4% of the age of the Solar System. The most likely explanation for this young martian volcanism is adiabatic decompression melting in upwelling mantle plumes. Multiple plumes may be active at any time, with each of the major volcanos in the Tharsis region being formed by a separate plume. Like at least some terrestrial mantle plumes, mantle plumes on Mars likely form via an instability of the thermal boundary layer at the base of the mantle. Because Mars operates in the stagnant lid convection regime, the temperature difference between mantle and core is lower than on Earth. This reduces the temperature contrast between mantle and core, resulting in mantle plumes on Mars that are about 100 K hotter than the average mantle. The chemical composition of the martian meteorites indicates that the martian mantle is enriched in both iron and sodium relative to Earth's mantle. This lowers the dry solidus on early Mars by 30-40 K relative to Earth. Migration of sodium to the crust over time decreases this difference in solidus temperature to about 15 K at present, but that is sufficient to increase the current plume magma production rate by a factor of about 2. Hydrous phases in the martian meteorites indicate the presence of a few hundred ppm water in the mantle source region, roughly the same as Earth. Finite element simulations of martian plumes using temperature-dependent viscosity and realistic Rayleigh numbers can reproduce the geologically recent magma production rate that is inferred from geologic mapping and the melt fraction inferred from trace element studies of martian meteorites. These plumes can also reproduce the observed spatial variability in elastic lithosphere thickness between regions of plume upwelling and regions that are far from the plumes. Melting in these models occurs at pressures of 3-5 GPa (250-400 km depth), reflecting the presence of a thick thermal lithosphere on present-day Mars. Meteorite evidence indicates that the martian mantle has about 10 times as much isotopic heterogeneity as Earth, which has sometimes been interpreted as evidence that the martian mantle is not convecting. This conclusion is incorrect, as the observed volcanos require some form of decompression melting and thus a convecting mantle. Few strike slip faults are observed on Mars, which indicates that flow in the mantle is almost entirely poloidal in nature, with little or no toroidal motion. The absence of toroidal flow on Mars makes convective mixing much less efficient than on Earth and permits the preservation of high levels of isotopic heterogeneity within a convecting mantle.

Effect of gaseous and solid simulated jet plumes on a 040A space shuttle launch configuration at Mach numbers from 1.6 to 2.2

NASA Technical Reports Server (NTRS)

Lanfranco, M. J.; Sparks, V. W.; Kavanaugh, A. T.

1973-01-01

An experimental investigation was conducted in a 9- by 7-foot supersonic wind tunnel to determine the effect of plume-induced flow separation and aspiration effects due to operation of both the orbiter and the solid rocket motors on a 0.019-scale model of the launch configuration of the space shuttle vehicle. Longitudinal and lateral-directional stability data were obtained at Mach numbers of 1.6, 2.0, and 2.2 with and without the engines operating. The plumes exiting from the engines were simulated by a cold gas jet supplied by an auxiliary 200 atmosphere air supply system, and by solid body plume simulators. Comparisons of the aerodynamic effects produced by these two simulation procedures are presented. The data indicate that the parameters most significantly affected by the jet plumes are the pitching moment, the elevon control effectiveness, the axial force, and the orbiter wing loads.

Determination of car on-road black carbon and particle number emission factors and comparison between mobile and stationary measurements

NASA Astrophysics Data System (ADS)

Ježek, I.; Drinovec, L.; Ferrero, L.; Carriero, M.; Močnik, G.

2015-01-01

We have used two methods for measuring emission factors (EFs) in real driving conditions on five cars in a controlled environment: the stationary method, where the investigated vehicle drives by the stationary measurement platform and the composition of the plume is measured, and the chasing method, where a mobile measurement platform drives behind the investigated vehicle. We measured EFs of black carbon and particle number concentration. The stationary method was tested for repeatability at different speeds and on a slope. The chasing method was tested on a test track and compared to the portable emission measurement system. We further developed the data processing algorithm for both methods, trying to improve consistency, determine the plume duration, limit the background influence and facilitate automatic processing of measurements. The comparison of emission factors determined by the two methods showed good agreement. EFs of a single car measured with either method have a specific distribution with a characteristic value and a long tail of super emissions. Measuring EFs at different speeds or slopes did not significantly influence the EFs of different cars; hence, we propose a new description of vehicle emissions that is not related to kinematic or engine parameters, and we rather describe the vehicle EF with a characteristic value and a super emission tail.

Automated ablation of dental composite using an IR pulsed laser coupled to a plume emission spectral feedback system.

PubMed

Jang, Andrew T; Chan, Kenneth H; Fried, Daniel

2017-09-01

The purpose of this study is to assemble a laser system for the selective removal of dental composite from tooth surfaces, that is feasible for clinical use incorporating a spectral feedback system, a scanning system, articulating arm and a clinical hand-piece, and evaluate the performance of that system on extracted teeth. Ten extracted teeth were collected and small fillings were placed on the occlusal surface of each tooth. A clinical system featuring a CO 2 laser operating at 50 Hz and spectral optical feedback was used to remove the composite. Removal was confirmed using a cross polarized optical coherence tomography (CP-OCT) system designed for clinical use. The system was capable of rapidly removing composite from small preparations on tooth occlusal surfaces with a mean loss of enamel of less than 20 μm. We have demonstrated that spectral feedback can be successfully employed in an automated system for composite removal by incorporating dual photodiodes and a galvanometer controlled CO 2 laser. Additionally, the use of registered OCT images presents as a viable method for volumetric benchmarking. Overall, this study represents the first implementation of spectral feedback into a clinical hand-piece and serves as a benchmark for a future clinical study. Lasers Surg. Med. 49:658-665, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Investigation of Tropospheric Pollutants and Stratospheric Ozone Using Infrared Fourier Transform Spectrometers from the Ground, Space and Balloons

NASA Astrophysics Data System (ADS)

Griffin, Debora

This thesis focusses on transport and composition of boreal fire plumes, evolution of trace gases in the Arctic, multi-year comparisons of ground-based and satellite-borne instruments, and depletion of Arctic ozone. Two similar Fourier Transform Spectrometer (FTS) instruments were utilized: (1) the ground-based and balloon-borne Portable Atmospheric Research Interferometric Spectrometer for the InfraRed (PARIS-IR) and (2) the space-borne Atmospheric Chemistry Experiment (ACE) FTS. Additional datasets, from other satellite and ground-based instruments, as well as Chemical Transport Models (CTMs) complemented the analysis. Transport and composition of boreal fire plumes were analysed with PARIS-IR measurements taken in Halifax, Nova Scotia. This study analysed the retrievals of different FTSs and investigated transport and composition of a smoke plume utilizing various models. The CO retrievals of three different FTSs (PARIS-IR, DA8, and IASI) were consistent and detected a smoke plume between 19 and 21 July 2011. These measurements were similar to the concentrations computed by GEOS-Chem ( 3% for CO and 8% for C2H6). Multi-year comparisons (2006-2013) of ground-based and satellite-borne FTSs near Eureka, Nunavut were carried out utilizing measurements from PARIS-IR, the Bruker 125HR and ACEFTS. The mean and interannual differences between the datasets were investigated for eight species (ozone, HCl, HNO3, HF, CH4, N2O, CO, and C2H6) and good agreement between these instruments was found. Furthermore, the evolution of the eight gases was investigated and increasing ozone, HCl, HF, CH4 and C2H6 were found. Springtime Arctic ozone depletion was studied, where six different methods to estimate ozone depletion were evaluated using the ACE-FTS dataset. It was shown that CH4, N2O, HF, and CCl2F2 are suitable tracers to estimate the ozone loss. The loss estimates (mixing ratio and partial column) are consistent for all six methods. Finally, PARIS-IR was prepared for a balloon-borne measurement campaign and a new suntracker for these measurements was designed and tested. The balloon was launched in September 2015. The suntracker performed with a +/-0.04° accuracy. From the balloon-borne sunset spectra, an ozone profile was retrieved and is consistent with measurements from a nearby ozonesonde within approximately 10 %.

Multiple enrichment of the Carpathian-Pannonian mantle: Pb-Sr-Nd isotope and trace element constraints

NASA Astrophysics Data System (ADS)

Rosenbaum, Jeffrey M.; Wilson, Marjorie; Downes, Hilary

1997-07-01

Pb isotope compositions of acid-leached clinopyroxene and amphibole mineral separates from spinel peridotite mantle xenoliths entrained in Tertiary-Quaternary alkali basalts from the Carpathian-Pannonian Region of eastern Europe provide important constraints on the processes of metasomatic enrichment of the mantle lithosphere in an extensional tectonic setting associated with recent subduction. Principal component analysis of Pb-Sr-Nd isotope and rare earth element compositions of the pyroxenes is used to identify the geochemical characteristics of the original lithospheric mantle protolith and a spectrum of infiltrating metasomatic agents including subduction-related aqueous fluids and silicate melts derived from a subduction-modified mantle wedge which contains a St. Helena-type (HIMU) plume component. The mantle protolith is highly depleted relative to mid-ocean ridge basalt-source mantle with Pb-Nd-Sr isotope compositions consistent with an ancient depletion event. Silicate melt infiltration into the protolith accounts for the primary variance in the Pb-Sr-Nd isotope compositions of the xenoliths and has locally generated metasomatic amphibole. Infiltration of aqueous fluids has introduced radiogenic Pb and Sr without significantly perturbing the rare earth element signature of the protolith. The Pb isotope compositions of the fluid-modified xenoliths suggest that they reacted with aqueous fluids released from a subduction zone which had equilibrated with sediment derived from an ancient basement terrain. We propose a model for mantle lithosphere evolution consistent with available textural and geochemical data for the xenolith population. The Pb-Sr-Nd isotope compositions of both alkaline mafic magmas and rare, subduction-related, calc-alkaline basaltic andesites from the region provide important constraints for the nature of the asthenospheric mantle wedge and confirm the presence of a HIMU plume component. These silicate melts contribute to the metasomatism of the mantle lithosphere rather than being derived therefrom.

In situ Volcanic Plume Monitoring with small Unmanned Aerial Systems for Cal/Val of Satellite Remote Sensing Data: CARTA-UAV 2013 Mission (Invited)

NASA Astrophysics Data System (ADS)

Diaz, J. A.; Pieri, D. C.; Bland, G.; Fladeland, M. M.

2013-12-01

The development of small unmanned aerial systems (sUAS) with a variety of sensor packages, enables in situ and proximal remote sensing measurements of volcanic plumes. Using Costa Rican volcanoes as a Natural Laboratory, the University of Costa Rica as host institution, in collaboration with four NASA centers, have started an initiative to develop low-cost, field-deployable airborne platforms to perform volcanic gas & ash plume research, and in-situ volcanic monitoring in general, in conjunction with orbital assets and state-of-the-art models of plume transport and composition. Several gas sensors have been deployed into the active plume of Turrialba Volcano including a miniature mass spectrometer, and an electrochemical SO2 sensor system with temperature, pressure, relative humidity, and GPS sensors. Several different airborne platforms such as manned research aircraft, unmanned aerial vehicles, tethered balloons, as well as man-portable in-situ ground truth systems are being used for this research. Remote sensing data is also collected from the ASTER and OMI spaceborne instruments and compared with in situ data. The CARTA-UAV 2013 Mission deployment and follow up measurements successfully demonstrated a path to study and visualize gaseous volcanic emissions using mass spectrometer and gas sensor based instrumentation in harsh environment conditions to correlate in situ ground/airborne data with remote sensing satellite data for calibration and validation purposes. The deployment of such technology improves on our current capabilities to detect, analyze, monitor, model, and predict hazards presented to aircraft by volcanogenic ash clouds from active and impending volcanic eruptions.

Motion Imagery and Robotics Application (MIRA): Standards-Based Robotics

NASA Technical Reports Server (NTRS)

Martinez, Lindolfo; Rich, Thomas; Lucord, Steven; Diegelman, Thomas; Mireles, James; Gonzalez, Pete

2012-01-01

This technology development originated from the need to assess the debris threat resulting from soil material erosion induced by landing spacecraft rocket plume impingement on extraterrestrial planetary surfaces. The impact of soil debris was observed to be highly detrimental during NASA s Apollo lunar missions and will pose a threat for any future landings on the Moon, Mars, and other exploration targets. The innovation developed under this program provides a simulation tool that combines modeling of the diverse disciplines of rocket plume impingement gas dynamics, granular soil material liberation, and soil debris particle kinetics into one unified simulation system. The Unified Flow Solver (UFS) developed by CFDRC enabled the efficient, seamless simulation of mixed continuum and rarefied rocket plume flow utilizing a novel direct numerical simulation technique of the Boltzmann gas dynamics equation. The characteristics of the soil granular material response and modeling of the erosion and liberation processes were enabled through novel first principle-based granular mechanics models developed by the University of Florida specifically for the highly irregularly shaped and cohesive lunar regolith material. These tools were integrated into a unique simulation system that accounts for all relevant physics aspects: (1) Modeling of spacecraft rocket plume impingement flow under lunar vacuum environment resulting in a mixed continuum and rarefied flow; (2) Modeling of lunar soil characteristics to capture soil-specific effects of particle size and shape composition, soil layer cohesion and granular flow physics; and (3) Accurate tracking of soil-borne debris particles beginning with aerodynamically driven motion inside the plume to purely ballistic motion in lunar far field conditions.

Mississippi River Plume Enriches Microbial Diversity in the Northern Gulf of Mexico

PubMed Central

Mason, Olivia U.; Canter, Erin J.; Gillies, Lauren E.; Paisie, Taylor K.; Roberts, Brian J.

2016-01-01

The Mississippi River (MR) serves as the primary source of freshwater and nutrients to the northern Gulf of Mexico (nGOM). Whether this input of freshwater also enriches microbial diversity as the MR plume migrates and mixes with the nGOM serves as the central question addressed herein. Specifically, in this study physicochemical properties and planktonic microbial community composition and diversity was determined using iTag sequencing of 16S rRNA genes in 23 samples collected along a salinity (and nutrient) gradient from the mouth of the MR, in the MR plume, in the canyon, at the Deepwater Horizon wellhead and out to the loop current. Analysis of these datasets revealed that the MR influenced microbial diversity as far offshore as the Deepwater Horizon wellhead. The MR had the highest microbial diversity, which decreased with increasing salinity. MR bacterioplankton communities were distinct compared to the nGOM, particularly in the surface where Actinobacteria and Proteobacteria dominated, while the deeper MR was also enriched in Thaumarchaeota. Statistical analyses revealed that nutrients input by the MR, along with salinity and depth, were the primary drivers in structuring the microbial communities. These results suggested that the reduced salinity, nutrient enriched MR plume could act as a seed bank for microbial diversity as it mixes with the nGOM. Whether introduced microorganisms are active at higher salinities than freshwater would determine if this seed bank for microbial diversity is ecologically significant. Alternatively, microorganisms that are physiologically restricted to freshwater habitats that are entrained in the plume could be used as tracers for freshwater input to the marine environment. PMID:27458442

Stratospheric aircraft exhaust plume and wake chemistry

NASA Technical Reports Server (NTRS)

Miake-Lye, R. C.; Martinez-Sanchez, M.; Brown, R. C.; Kolb, C. E.; Worsnop, D. R.; Zahniser, M. S.; Robinson, G. N.; Rodriguez, J. M.; Ko, M. K. W.; Shia, R-L.

1993-01-01

Progress to date in an ongoing study to analyze and model emissions leaving a proposed High Speed Civil Transport (HSCT) from when the exhaust gases leave the engine until they are deposited at atmospheric scales in the stratosphere is documented. A kinetic condensation model was implemented to predict heterogeneous condensation in the plume regime behind an HSCT flying in the lower stratosphere. Simulations were performed to illustrate the parametric dependence of contrail droplet growth on the exhaust condensation nuclei number density and size distribution. Model results indicate that the condensation of water vapor is strongly dependent on the number density of activated CN. Incorporation of estimates for dilution factors into a Lagrangian box model of the far-wake regime with scale-dependent diffusion indicates negligible decrease in ozone and enhancement of water concentrations of 6-13 times background, which decrease rapidly over 1-3 days. Radiative calculations indicate a net differential cooling rate of the plume about 3K/day at the beginning of the wake regime, with a total subsidence ranging between 0.4 and 1 km. Results from the Lagrangian plume model were used to estimate the effect of repeated superposition of aircraft plumes on the concentrations of water and NO(y) along a flight corridor. Results of laboratory studies of heterogeneous chemistry are also described. Kinetics of HCl, N2O5 and ClONO2 uptake on liquid sulfuric acid were measured as a function of composition and temperature. Refined measurements of the thermodynamics of nitric acid hydrates indicate that metastable dihydrate may play a role in the nucleation of more stable trihydrates PSC's.

Fringe-controlled biodegradation under dynamic conditions: Quasi 2-D flow-through experiments and reactive-transport modeling

NASA Astrophysics Data System (ADS)

Eckert, Dominik; Kürzinger, Petra; Bauer, Robert; Griebler, Christian; Cirpka, Olaf A.

2015-01-01

Biodegradation in contaminated aquifers has been shown to be most pronounced at the fringe of contaminant plumes, where mixing of contaminated water and ambient groundwater, containing dissolved electron acceptors, stimulates microbial activity. While physical mixing of contaminant and electron acceptor by transverse dispersion has been shown to be the major bottleneck for biodegradation in steady-state plumes, so far little is known on the effect of flow and transport dynamics (caused, e.g., by a seasonally fluctuating groundwater table) on biodegradation in these systems. Towards this end we performed experiments in quasi-two-dimensional flow-through microcosms on aerobic toluene degradation by Pseudomonas putida F1. Plume dynamics were simulated by vertical alteration of the toluene plume position and experimental results were analyzed by reactive-transport modeling. We found that, even after disappearance of the toluene plume for two weeks, the majority of microorganisms stayed attached to the sediment and regained their full biodegradation potential within two days after reappearance of the toluene plume. Our results underline that besides microbial growth, also maintenance and dormancy are important processes that affect biodegradation performance under transient environmental conditions and therefore deserve increased consideration in future reactive-transport modeling.

The study on spatial distribution features of radiological plume discharged from Nuclear Power Plant based on C4ISRE

NASA Astrophysics Data System (ADS)

Ma, Yunfeng; Shen, Yue; Feng, Bairun; Yang, Fan; Li, Qiangqiang; Du, Boying; Bian, Yushan; Hu, Qiongqong; Wang, Qi; Hu, Xiaomin; Yin, Hang

2018-02-01

When the nuclear emergency accident occurs, it is very important to estimate three-dimensional space feature of the radioactive plume discharged from the source term for the emergency organization, as well as for better understanding of atmospheric dispersion processes. So, taking the Hongyanhe Nuclear Power Plant for example, the study for three-dimensional space feature of the radioactive plume is accomplished by applying atmospheric transport model (coupling of WRF-HYSPLIT) driven by FNL meteorological data of NCEP (04/01/2014-04/02/2014) based on the C4ISRE (Command, Control, Communications, Computer, Intelligence, Surveillance, Reconnaissance, Environmental Impact Assessment).The results show that the whole shape of three-dimensional plume was about irregular cloth influenced by wind; In the spatial domain (height > 16000m),the distribution of radiological plume, which looked more like horseshoe-shaped, presented irregular polygons of which the total length was 2258.7km, where covered the area of 39151km2; In the airspace from 4000m to 16000m, the plume, covered the area of 116269 km2, showed a triangle and the perimeter of that was 2280.4km; The shape of the plume was more like irregular quadrilateral, its perimeter was 2941.8km and coverage area of the plume was 131534km2;The overall distribution of the wind field showed a rectangular shape; Within the area along the horizontal direction 400m from origin to east and under height (lower than 2000m),the closer the distance coordinate (0,0), the denser the plume particles; Within the area of horizontal distance(500m-1000m) and height (4000m- 16000m), the particle density were relatively sparse and the spread extent of the plume particles from west to East was relatively large and the plume particles were mainly in the suspended state without obvious dry sedimentation; Within the area of horizontal distance (800m-1100m) and height (>16000m), there were relatively gentle horizontal diffusion of plume particles with upward drift of particles In local area.

Sulfur balance in power plant plumes: a critical review

Treesearch

William E. Wilson

1976-01-01

Numerous attempts have been made to measure the rate of loss of SO2 in power plant plumes. If SO2 decreases more rapidly than an inert pollutant, the control measures necessary to meet SO2 standards would be eased. More recently, Swedish studies of acid rain, thought to be due to long range transport...

Primitive helium isotopic compositions associated with Miocene lavas from Northwest Iceland

NASA Astrophysics Data System (ADS)

Jackson, M. G.; Reinhard, A.; Blichert-Toft, J.; Price, A. A.; Kurz, M. D.; Halldorsson, S. A.

2016-12-01

Elevated 3He/4He ratios identified in hotspots globally are associated with an early-formed, less degassed mantle reservoir that resides in the deep mantle, but the origin and mechanism for the long-term preservation of this mantle domain are not well understood. The highest known terrestrial mantle-derived 3He/4He ratios (49.5 Ra) have been measured in 62 million year old lavas from Baffin Island and West Greenland, associated with the proto-Iceland plume [1]. Mid-Miocene lavas from northwest Iceland have 3He/4He ratios of up to 37 Ra [2]. Thus, the Iceland plume has tapped a high-3He/4He mantle source over much of the Cenozoic. This is important, as 182W [3] and 129Xe [4] data indicate that the high 3He/4He domain sampled by the Iceland plume formed in the early Hadean. We report new 3He/4He measurements on magmatic olivine in mid-Miocene lavas from Northwest Iceland. Fusion experiments indicate that the new, high 3He/4He ratios do not have a cosmogenic 3He contribution. New Sr, Nd, Hf, and Pb isotopic data place important constraints on the isotopic composition of the highest 3He/4He mantle domain sampled by mid-Miocene Iceland lavas. An important question is whether the highest 3He/4He lavas from Iceland have Sr-Nd-Hf-Pb isotopic compositions that overlap with those found in the high-3He/4He lavas from Baffin Island. If not, it will be important to understand the mechanism responsible for the offset in Sr-Nd-Hf-Pb isotopic compositions, and whether this also explains the lower maximum 3He/4He in mid-Miocene Icelandic lavas relative to their counterparts in Baffin Island. The new data will have implications for the preservation of primitive reservoirs in the deep mantle. [1] Stuart et al., Nature, v. 424, 2003. [2] Hilton et al., Earth Planet Sci. Lett., v. 173, 1999. [3] Rizo et al., Science, v. 352, 2016. [4] Mukhopadhyay, Nature, v. 486, 2012.

Small scale inhomogeneity in the mantle source of the Cape Verde hotspot is probably related to plume complexity: implications from Sr, Nd and high precision Pb isotopes and geochemistry

NASA Astrophysics Data System (ADS)

Holm, P. M.; Sørensen, R. V.

2009-04-01

The volcanic rocks of one of the major islands of the Cape Verde hotspot have been investigated in order to test mantle plume models. From the centre of the Cape Verde Rise an array of islands trend west, the northern HIMU-type Cape Verde Islands. Of these, São Nicolau (SN) is the easternmost and Santo Antão the westernmost. Sixty samples of primitive (MgO = 9-14 wt%) basanitic composition from SN that represent the four volcanic stages of the 9 - 0.1 Ma evolution of the island have been analysed for Sr, Nd and high precision Pb isotopic composition. Pb ranges to a less radiogenic composition than on SA [1] and has lower 8/4 than the rocks of the southern EM1-type Cape Verde islands. Most SN lavas have a young HIMU character with negative 7/4. The most radiogenic Pb at SN is less thorogenic than Pb at SA. Temporal variation is also evident: An intermediate age group of samples have particularly low La/Nb = 0.4 - 0.5 and the least LREE-enrichment for SN. The youngest group of rocks has the lowest Zr/Nb = 2.5 - 3.0 and the most unradiogenic Sr and radiogenic Nd in the archipelago. At least four of the mantle source components for the SN magmas are different from any found in the SA magmas. High precision Pb data allow identification of parallel trends for northern SN and the southern island Santiago, which therefore must have unrelated source components. For the northern Cape Verde islands source compositions vary from E to W as well as with time. This cannot be explained by stationary enriched lithosphere components. The derivation of melts from a complex plume source is modelled. [1] Holm P.M., Wilson J.R., Christensen B.P., Hansen S.L., Hein K.M., Mortensen A.K., Pedersen R., Plesner S., and Runge M.K. (2006) JPetrol 47, 145-189.

Geochemical evidence of mantle reservoir evolution during progressive rifting along the western Afar margin

NASA Astrophysics Data System (ADS)

Rooney, Tyrone O.; Mohr, Paul; Dosso, Laure; Hall, Chris

2013-02-01

The Afar triple junction, where the Red Sea, Gulf of Aden and African Rift System extension zones converge, is a pivotal domain for the study of continental-to-oceanic rift evolution. The western margin of Afar forms the southernmost sector of the western margin of the Red Sea rift where that margin enters the Ethiopian flood basalt province. Tectonism and volcanism at the triple junction had commenced by ˜31 Ma with crustal fissuring, diking and voluminous eruption of the Ethiopian-Yemen flood basalt pile. The dikes which fed the Oligocene-Quaternary lava sequence covering the western Afar rift margin provide an opportunity to probe the geochemical reservoirs associated with the evolution of a still active continental margin. 40Ar/39Ar geochronology reveals that the western Afar margin dikes span the entire history of rift evolution from the initial Oligocene flood basalt event to the development of focused zones of intrusion in rift marginal basins. Major element, trace element and isotopic (Sr-Nd-Pb-Hf) data demonstrate temporal geochemical heterogeneities resulting from variable contributions from the Afar plume, depleted asthenospheric mantle, and African lithosphere. The various dikes erupted between 31 Ma and 22 Ma all share isotopic signatures attesting to a contribution from the Afar plume, indicating this initial period in the evolution of the Afar margin was one of magma-assisted weakening of the lithosphere. From 22 Ma to 12 Ma, however, diffuse diking during continued evolution of the rift margin facilitated ascent of magmas in which depleted mantle and lithospheric sources predominated, though contributions from the Afar plume persisted. After 10 Ma, magmatic intrusion migrated eastwards towards the Afar rift floor, with an increasing fraction of the magmas derived from depleted mantle with less of a lithospheric signature. The dikes of the western Afar margin reveal that magma generation processes during the evolution of this continental rift margin are increasingly dominated by shallow decompressional melting of the ambient asthenosphere, the composition of which may in part be controlled by preferential channeling of plume material along the developing neo-oceanic axes of extension.

Observed Spatial and Temporal Variability of Subglacial Discharge-Driven Plumes in Greenland's Outlet Glacial Fjords

NASA Astrophysics Data System (ADS)

Sutherland, D.; Carroll, D.; Nash, J. D.; Shroyer, E.; Mickett, J.; Stearns, L. A.; Fried, M.; Bartholomaus, T.; Catania, G. A.

2015-12-01

Hydrographic and velocity observations in Greenland's outlet glacier fjords have revealed, unsurprisingly, a rich set of dynamics over a range of spatial and temporal scales. Through teasing apart the distinct processes that control circulation within these fjords, we are likely to better understand the impact of fjord circulation on modulating outlet glacier dynamics, and thus, changes in Greenland Ice Sheet mass balance. Here, we report on data from the summers of 2013-2015 in two neighboring fjords in the Uummannaq Bay region of west Greenland: Kangerlussuup Sermia (KS) and Rink Isbræ (RI). We find strong subglacial discharge driven plumes in both systems that evolve on synoptic and seasonal time scales, without the complicating presence of other circulation processes. The plumes both modify fjord water properties and respond to differences in ambient water properties, supporting the notion that a feedback exists between subglacial discharge plume circulation and water mass properties. This feedback between subglacial discharge and water properties potentially influences submarine melt rates at the glacier termini. Observed plume properties, including the vertical structure of velocity, and temperature and salinity anomalies, are compared favorably to model estimates. In KS, we find a near-surface intensified plume with high sediment content that slows and widens as it evolves downstream. In contrast, the plume in RI is entirely subsurface, ranging from 100-300 m depth at its core during summer, although it shows similar temperature, salinity, and optical backscatter signals to the KS plume. Importantly, the distinct vertical plume structures imprint on the overall water mass properties found in each fjord, raising the minimum temperatures by up to 1-2°C in the case of RI.

Geodynamic modeling of the capture and release of a plume conduit by a migrating mid-ocean ridge

NASA Astrophysics Data System (ADS)

Hall, P. S.

2011-12-01

plates over the relatively stationary, long-lived conduits of mantle plumes. However, paleomagnetic data from the Hawaii-Emperor Seamount Chain suggests that the Hawaiian hotspot moved rapidly (~40 mm/yr) between 81 - 47 Ma [Tarduno et al., 2003]. Recently, Tarduno et al. [2009] suggested that this period of rapid motion might be the surface expression of a plume conduit returning to a largely vertical orientation after having been captured and tilted as the result of being "run over" by migrating mid-ocean ridge. I report on a series of analog geodynamic experiments designed to characterize the evolution of a plume conduit as a mid-ocean ridge migrates over. Experiments were conducted in a clear acrylic tank (100 cm x 70 cm x 50 cm) filled with commercial grade high-fructose corn syrup. Plate-driven flow is modeled by dragging two sheets of Mylar film (driven by independent DC motors) in opposite directions over the surface of the fluid. Ridge migration is achieved by moving the point at which the mylar sheets diverge using a separate motor drive. Buoyant plume flow is generated using a small electrical heater placed at the bottom of the tank. Plate velocities and ridge migration rate are controlled and plume temperature monitored using LabView software. Experiments are recorded using digital video which is then analyzed using digital image analysis software to track the position and shape of the plume conduit throughout the course of the experiment. The intersection of the plume conduit with the surface of the fluid is taken as an analog for the locus of hotspot volcanism and tracked as a function of time to obtain a hotspot migration rate. Results show that the plume conduit experiences significant tilting immediately following the passage of the migrating ridge.

Is the 'Fast Halo' around Hawaii as imaged in the PLUME experiment direct evidence for buoyant plume-fed asthenosphere?

NASA Astrophysics Data System (ADS)

Morgan, J. P.; Shi, C.; Hasenclever, J.

2010-12-01

An intriguing spatial pattern of variations in shear-wave arrival times has been mapped in the PLUME ocean bottom experiment (Wolfe et al., 2009) around Hawaii. The pattern consists of a halo of fast travel times surrounding a disk of slow arrivals from waves traveling up though the plume. We think it is directly sensing the pattern of dynamic uplift of the base of a buoyant asthenosphere - the buoyancy of the plume conduit lifting a 'rim' of the cooler, denser mantle that the plume rises through. The PLUME analysis inverted for lateral shear velocity variations beneath the lithosphere, after removing the assumed 1-D model velocity structure IASP91. They found that a slow plume-conduit extends to at least 1200 km below the Hawaiian hotspot. In this inversion the slow plume conduit is — quite surprisingly - surrounded by a fast wavespeed halo. A fast halo is impossible to explain as a thermal halo around the plume; this should lead to a slow wavespeed halo, not a fast one. Plume-related shearwave anisotropy also cannot simply explain this pattern — simple vertical strain around the plume conduit would result in an anisotropic slow shear-wavespeed halo, not a fast one. (Note the PLUME experiment’s uniform ‘fast-halo’ structure from 50-400km is likely to have strong vertical streaking in the seismic image; Pacific Plate-driven shear across a low-viscosity asthenosphere would be expected to disrupt and distort any cold sheet of vertical downwelling structure between 50-400km depths so that it would no longer be vertical as it is in the 2009 PLUME image with its extremely poor vertical depth control.) If the asthenosphere is plume-fed, hence more buoyant than underlying mantle, then there can be a simple explanation for this pattern. The anomaly would be due to faster traveltimes resulting from dynamic relief at the asthenosphere-mesosphere interface; uplift of the denser mesosphere by the buoyancy of the rising plume increases the distance a wave travels through faster mantle and reduces the distance though the slower asthenosphere. With this interpretation, the inference of a radially symmetric ~40-70 km high-~250 km-radius ‘bump’ of uplift of the base of buoyant plume-fed asthenosphere (PFA) can be directly estimated from PLUME results and the measured ~6-10% reduction in shear velocity between the PFA and underlying mantle. The inferred dynamic relief at the base of the PFA due to buoyancy within the underlying plume conduit is strikingly similar to the relief we find in recent axisymmetric 2D and Cartesian 3-D numerical experiments that explore the dynamics of mantle convection with a PFA. The width and height of the bump scale directly with the total buoyancy anomaly in the upper ~500km of the plume conduit, we discuss numerical experiments that quantify this relationship, show that it is, to first order, independent of the viscosity of material in the plume conduit or asthenosphere, and which also quantify the ~400km-radius geoid anomaly produced by these subasthenospheric mantle density anomalies. This effect can only happen if the asthenosphere is more buoyant than underlying mantle — and is therefore direct evidence that a buoyant plume-fed asthenosphere exists around Hawaii.

Controls of Plume Dispersal at the Slow Spreading Mid-Atlantic Ridge

NASA Astrophysics Data System (ADS)

Walter, M.; Mertens, C.; Koehler, J.; Sueltenfuss, J.; Rhein, M.; Keir, R. S.; Schmale, O.; Schneider v. Deimling, J.; German, C. R.; Yoerger, D. R.; Baker, E. T.

2011-12-01

The slow-spreading Mid-Atlantic Ridges hosts a multitude of different types of hydrothermal systems. Here, we compare the fluxes and the plume dispersal at three high temperature sites located in very diverse settings at comparable depths (~3000m): The recently discovered sites Turtle Pits, and Nibelungen on the southern MAR, and the Logatchev field in the North Atlantic. Plume mapping for these sites on cruises between 2004 and 2009 consisted of CTD Towyo-, Yoyo,- and station work, including velocity profiling, as well as water sampling for analysis of trace gases (CH4, H2, 3He/4He) and metals; temperature measurements and fluid sampling at the vent sites were carried out with an ROV. The aim of this work is to gain a better understanding of how the setting of a vent site affects the dispersal of the particle plume, and what means can be used to infer possible locations of vent sites based on the hydrographic properties and plume observations, using high resolution bathymetric mapping and hydrographic information. The ultramafic-hosted Nibelungen site (8°18'S) consists of a single active smoking crater, along with several extinct smokers, which is located off-axis south of a non-transform offset. The setting is characterized by rugged topography, favorable for the generation of internal tides, internal wave breaking, and vertical mixing. Elevated mixing with turbulent diffusivities Kρ up to 0.1 m2 s-1, 3 to 4 orders of magnitude higher than open ocean values, was observed close to the vent site. The mixing as well as the flow field exhibited a strong tidal cycle; the plume dispersal is thus dominated by the fast and intermittent vertical exchange and characterized by small scale spatial and temporal variability. The Turtle Pits vent fields (4°48'S) are located on a sill in a north-south orientated rift valley. The site consists of three (known) high temperature fields: Turtle Pits, Comfortless Cove, and Red Lion. The particle plume is confined to the rift valley since the depth of the valley exceeds the rise height of the plume. Velocities observed with a Lowered Acoustic Doppler Current Profiler (LADCP), and the gradient of the stratification across the sill show a hydraulic control of the background flow over the sill, resulting in a northward advection of plume material. Downstream, the particle plume is modified by a dominant across-valley tide, and strong vertical mixing in the wake of the hydraulic jump. The Logatchev hydrothermal field (14°45'N) consists of seven vent sites, mostly smoking craters, located up on the eastern flank of the axial graben. The current field as observed with LADCP is irregular, but follows to some extent the topography in the range of the particle plume. This plume is sheared in the vertical, indicating the influence of the local tides.

Innovative Use of Cr(VI) Plume Depictions and Pump-and-Treat Capture Analysis to Estimate Risks of Contaminant Discharge to Surface Water at Hanford Reactor Areas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, Chuck W.; Hanson, James P.; Ivarson, Kristine A.

2015-01-14

The Hanford Site nuclear reactor operations required large quantities of high-quality cooling water, which was treated with chemicals including sodium dichromate dihydrate for corrosion control. Cooling water leakage, as well as intentional discharge of cooling water to ground during upset conditions, produced extensive groundwater recharge mounds consisting largely of contaminated cooling water and resulted in wide distribution of hexavalent chromium (Cr[VI]) contamination in the unconfined aquifer. The 2013 Cr(VI) groundwater plumes in the 100 Areas cover approximately 6 km2 (1500 acres), primarily in the 100-HR-3 and 100-KR-4 groundwater operable units (OUs). The Columbia River is a groundwater discharge boundary; wheremore » the plumes are adjacent to the Columbia River there remains a potential to discharge Cr(VI) to the river at concentrations above water quality criteria. The pump-and-treat systems along the River Corridor are operating with two main goals: 1) protection of the Columbia River, and 2) recovery of contaminant mass. An evaluation of the effectiveness of the pump-and-treat systems was needed to determine if the Columbia River was protected from contamination, and also to determine where additional system modifications may be needed. In response to this need, a technique for assessing the river protection was developed which takes into consideration seasonal migration of the plume and hydraulic performance of the operating well fields. Groundwater contaminant plume maps are generated across the Hanford Site on an annual basis. The assessment technique overlays the annual plume and the capture efficiency maps for the various pump and treat systems. The river protection analysis technique was prepared for use at the Hanford site and is described in detail in M.J. Tonkin, 2013. Interpolated capture frequency maps, based on mapping dynamic water level observed in observation wells and derived water levels in the vicinity of extraction and injection wells, are developed initially. Second, simulated capture frequency maps are developed, based on transport modelling results. Both interpolated and simulated capture frequency maps are based on operation of the systems over a full year. These two capture maps are then overlaid on the plume distribution maps for inspection of the relative orientation of the contaminant plumes with the capture frequency. To quantify the relative degree of protection of the river from discharges of Cr(VI) (and conversely, the degree of threat) at any particular location, a systematic method of evaluating and mapping the plume/capture relationship was developed. By comparing the spatial relationship between contaminant plumes and hydraulic capture frequency, an index of relative protectiveness is developed and the results posted on the combined plume/capture plan view map. Areas exhibiting lesser degrees of river protection are identified for remedial process optimization actions to control plumes and prevent continuing discharge of Cr(VI) to the river.« less

PRODUCTION AND TRANSPORT OF CARBON DIOXIDE IN A CONTAMINATED VADOSE ZONE: A STABLE AND RADIOACTIVE CARBON ISOTOPE STUDY

EPA Science Inventory

Analyses of soil gas compositions and stable and radioactive carbon isotopes in the vadose zone above an alluvial aquifer were conducted at an organic solvent disposal site in southeast Phoenix, AZ. The study investigated the source and movement of carbon dioxide above a plume of...

Deep-sea oil plume enriches psychrophilic oil-degrading bacteria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hazen, T.C.; Dubinsky, E.A.; DeSantis, T.Z.

The biological effects and expected fate of the vast amount of oil in the Gulf of Mexico from the Deepwater Horizon blowout are unknown owing to the depth and magnitude of this event. Here, we report that the dispersed hydrocarbon plume stimulated deep-sea indigenous {gamma}-Proteobacteria that are closely related to known petroleum degraders. Hydrocarbon-degrading genes coincided with the concentration of various oil contaminants. Changes in hydrocarbon composition with distance from the source and incubation experiments with environmental isolates demonstrated faster-than-expected hydrocarbon biodegradation rates at 5 C. Based on these results, the potential exists for intrinsic bioremediation of the oil plumemore » in the deep-water column without substantial oxygen drawdown.« less

Pulsed Plasma Thruster Plume Study: Symmetry and Impact on Spacecraft Surfaces

NASA Technical Reports Server (NTRS)

Arrington, Lynn A.; Marrese, Colleen M.; Blandino, John J.

2000-01-01

Twenty-four witness plates were positioned on perpendicular arrays near a breadboard Pulsed Plasma Thruster (PPT) to collect plume constituents for analysis. Over one million shots were fired during the experiment at 43 J using fluorocarbon polymer propellant. The asymmetry of the film deposition on the witness plates was investigated with mass and thickness measurements and correlated with off-axis thrust vector measurements. The composition of the films was determined. The transmittance and reflectance of the films were measured and the absorption coefficients were calculated in the wavelength range from 350 to 1200 mn. These data were applied to calculate the loss in signal intensity through the films, which will impact the visibility of spaceborne interferometer systems positioned by these thrusters.

Laser ablation and deposition of wide bandgap semiconductors: plasma and nanostructure of deposits diagnosis

NASA Astrophysics Data System (ADS)

Sanz, M.; López-Arias, M.; Rebollar, E.; de Nalda, R.; Castillejo, M.

2011-12-01

Nanostructured CdS and ZnS films on Si (100) substrates were obtained by nanosecond pulsed laser deposition at the wavelengths of 266 and 532 nm. The effect of laser irradiation wavelength on the surface structure and crystallinity of deposits was characterized, together with the composition, expansion dynamics and thermodynamic parameters of the ablation plume. Deposits were analyzed by environmental scanning electron microscopy, atomic force microscopy and X-ray diffraction, while in situ monitoring of the plume was carried out with spectral, temporal and spatial resolution by optical emission spectroscopy. The deposits consist of 25-50 nm nanoparticle assembled films but ablation in the visible results in larger aggregates (150 nm) over imposed on the film surface. The aggregate free films grown at 266 nm on heated substrates are thicker than those grown at room temperature and in the former case they reveal a crystalline structure congruent with that of the initial target material. The observed trends are discussed in reference to the light absorption step, the plasma composition and the nucleation processes occurring on the substrate.

In situ laser-induced breakdown spectroscopy measurements of chemical compositions in stainless steels during tungsten inert gas welding

NASA Astrophysics Data System (ADS)

Taparli, Ugur Alp; Jacobsen, Lars; Griesche, Axel; Michalik, Katarzyna; Mory, David; Kannengiesser, Thomas

2018-01-01

A laser-induced breakdown spectroscopy (LIBS) system was combined with a bead-on-plate Tungsten Inert Gas (TIG) welding process for the in situ measurement of chemical compositions in austenitic stainless steels during welding. Monitoring the weld pool's chemical composition allows governing the weld pool solidification behavior, and thus enables the reduction of susceptibility to weld defects. Conventional inspection methods for weld seams (e.g. ultrasonic inspection) cannot be performed during the welding process. The analysis system also allows in situ study of the correlation between the occurrence of weld defects and changes in the chemical composition in the weld pool or in the two-phase region where solid and liquid phase coexist. First experiments showed that both the shielding Ar gas and the welding arc plasma have a significant effect on the selected Cr II, Ni II and Mn II characteristic emissions, namely an artificial increase of intensity values via unspecific emission in the spectra. In situ investigations showed that this artificial intensity increase reached a maximum in presence of weld plume. Moreover, an explicit decay has been observed with the termination of the welding plume due to infrared radiation during sample cooling. Furthermore, LIBS can be used after welding to map element distribution. For austenitic stainless steels, Mn accumulations on both sides of the weld could be detected between the heat affected zone (HAZ) and the base material.

Editorial

NASA Astrophysics Data System (ADS)

Burton, Mike

2015-07-01

Magmatic degassing plays a key role in the dynamics of volcanic activity and also in contributing to the carbon, water and sulphur volatile cycles on Earth. Quantifying the fluxes of magmatic gas emitted from volcanoes is therefore of fundamental importance in Earth Science. This has been recognised since the beginning of modern volcanology, with initial measurements of volcanic SO2 flux being conducted with COrrelation SPECtrometer instruments from the late seventies. While COSPEC measurements continue today, they have been largely superseded by compact grating spectrometers, which were first introduced soon after the start of the 21st Century. Since 2006, a new approach to measuring fluxes has appeared, that of quantitative imaging of the SO2 slant column amount in a volcanic plume. Quantitative imaging of volcanic plumes has created new opportunities and challenges, and in April 2013 an ESF-funded MeMoVolC workshop was held, with the objectives of bringing together the main research groups, create a vibrant, interconnected, community, and examine the current state of the art of this new research frontier. This special issue of sixteen papers within the Journal of Volcanology and Geothermal Research is the direct result of the discussions, intercomparisons and results reported in that workshop. The papers report on the volcanological objectives of the plume imaging community, the state of the art of the technology used, intercomparisons, validations, novel methods and results from field applications. Quantitative plume imaging of volcanic plumes is achieved by using both infrared and ultraviolet wavelengths, with each wavelength offering a different trade-off of strengths and weaknesses, and the papers in this issue reflect this wavelength flexibility. Gas compositions can also be imaged, and this approach offers much promise in the quantification of chemical processing within plumes. One of the key advantages of the plume imaging approach is that we can achieve gas flux measurements at 1-10 Hz frequencies, allowing direct comparisons with geophysical measurements, opening new, interdisciplinary opportunities to deepen our understanding of volcanological processes. Several challenges still can be improved upon, such as dealing with light scattering issues and full automation of data processing. However, it is clear that quantitative plume imaging will have a lasting and profound impact on how volcano observatories operate, our ability to forecast and manage volcanic eruptions, our constraints of global volcanic gas fluxes, and on our understanding of magma dynamics.

Major components of seawater and hydrothermal plumes in the Okinawa Trough, East China Sea, and Yellow Sea

NASA Astrophysics Data System (ADS)

Zeng, Z.; Rong, K.; Chen, C. T. A.; Wang, X.; Qi, H.

2017-12-01

Analyses of the major components of seawater and hydrothermal plumes in hydrothermal fields are essential for an improved understanding of ocean carbonate system, element solubility and redox reactions (e.g., iron and copper). The composition of major components in seawater and hydrothermal plume samples from 118 stations have been investigated in the Okinawa Trough (OT), East China Sea (ECS), and Yellow Sea (YS). At least seven water masses take part in the mixing processes: the Kuroshio water, OT water, ECS water, YS water, Taiwan Strait water, vent fluid and hydrothermal plume water. About 6 - 16 % of the plume water comes from the Kuroshio deep water, 50 - 64% of the hydrothermal plume water comes from the vent fluid in the wet and dry season. In addition, the calculated SHVF (36 and 36.8) and SHPW (35 and 35.8) values are higher than the measured salinity values (34.4) of hydrothermal plumes in the OT. Major elements exhibit linear correlation in seawater (e.g., B3+ and Sr2+) of the OT, the ECS, and the YS. Element ratios (e.g., Sr/Ca, Ca/Cl) in OT water column are similar to that in average seawater, indicating that Sr/Ca and Ca/Cl ratios might be a useful proxy for chemical properties of seawater. Furthermore, from the southern and middle OT to the northern OT, ECS, and YS, the salinity, potential density, Cl/salinity ratio of seawater tend to decrease. The positive correlations between major components (e.g., SO42-, Cl-), physical properties (e.g., salinity, temperature, potential density) and current (velocity) in the seawater column suggests that the physical and chemical properties of seawater in the OT are affected by input of the Kuroshio current. In the Iheya North knoll, Clam, Yonaguni Knoll IV, and Tangyin hydrothermal fields of the OT, anomalous layers of seawater in the water column have higher Ca/SO42-, Mn/Mg ratios and higher optical anomalies than other layers, suggesting that the chemical variations of hydrothermal plumes result in the discharge of high Ca2+ and low Mg2+ fluid. The Ca2+and Mn2+ flux to seawater in the OT is about 1.04-326 and 1.30-76.4 ×1012 kg per year, respectively. The heat flux is about 0.159-1,973 ×105 W, which means that roughly 0.0006 % of ocean heat is supplied by seafloor hydrothermal plumes in the OT.

AVAL - The ASTER Volcanic Ash Library

NASA Astrophysics Data System (ADS)

Williams, D.; Ramsey, M. S.

2016-12-01

Volcanic ash is a rich data source for understanding the causal mechanisms behind volcanic eruptions. Petrologic and morphometric information can provide direct information on the characteristics of the parent magma. Understanding how erupted ash interacts with the atmosphere can help quantify the effect that explosive volcanism has on the local to regional climate, whereas a measure of the particle size distribution enables more accurate modeling of plume propagation. Remote sensing is regularly employed to monitor volcanic plumes using a suite of high temporal/low spatial resolution sensors. These methods employ radiative transfer modeling with assumptions of the transmissive properties of infrared energy through the plume to determine ash density, particle size and sulfur dioxide content. However, such approaches are limited to the optically-transparent regions, and the low spatial resolution data are only useful for large-scale trends. In a new approach, we are treating the infrared-opaque regions of the plume in a similar way to a solid emitting surface. This allows high spatial resolution orbital thermal infrared data from the dense proximal plume to be modeled using a linear deconvolution approach coupled with a spectral library to extract the particle size and petrology. The newly created ASTER Volcanic Ash Library (AVAL) provides the end member spectral suite, and is comprised of laboratory emission measurements of volcanic ash taken from a variety of different volcanic settings, to obtain a wide range of petrologies. These samples have been further subdivided into particle size fractions to account for spectral changes due to diffraction effects. Once mapped to the ASTER sensor's spectral resolution, this library is applied to image data and the plume deconvolved to estimate composition and particle size. We have analyzed eruptions at the Soufrière Hills Volcano, Montserrat, Chaitén and Puyehue-Cordón Caulle, both Chile, and Eyjafjallajökull, Iceland. These results provide particle size distributions within actively-erupting volcanic plumes for the first time in high resolution, and the petrologic information is being studied to understand the underlying eruptive processes observed.

CALIOP-based Biomass Burning Smoke Plume Injection Height

NASA Astrophysics Data System (ADS)

Soja, A. J.; Choi, H. D.; Fairlie, T. D.; Pouliot, G.; Baker, K. R.; Winker, D. M.; Trepte, C. R.; Szykman, J.

2017-12-01

Carbon and aerosols are cycled between terrestrial and atmosphere environments during fire events, and these emissions have strong feedbacks to near-field weather, air quality, and longer-term climate systems. Fire severity and burned area are under the control of weather and climate, and fire emissions have the potential to alter numerous land and atmospheric processes that, in turn, feedback to and interact with climate systems (e.g., changes in patterns of precipitation, black/brown carbon deposition on ice/snow, alteration in landscape and atmospheric/cloud albedo). If plume injection height is incorrectly estimated, then the transport and deposition of those emissions will also be incorrect. The heights to which smoke is injected governs short- or long-range transport, which influences surface pollution, cloud interaction (altered albedo), and modifies patterns of precipitation (cloud condensation nuclei). We are working with the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) science team and other stakeholder agencies, primarily the Environmental Protection Agency and regional partners, to generate a biomass burning (BB) plume injection height database using multiple platforms, sensors and models (CALIOP, MODIS, NOAA HMS, Langley Trajectory Model). These data have the capacity to provide enhanced smoke plume injection height parameterization in regional, national and international scientific and air quality models. Statistics that link fire behavior and weather to plume rise are crucial for verifying and enhancing plume rise parameterization in local-, regional- and global-scale models used for air quality, chemical transport and climate. Specifically, we will present: (1) a methodology that links BB injection height and CALIOP air parcels to specific fires; (2) the daily evolution of smoke plumes for specific fires; (3) plumes transport and deposited on the Greenland Ice Sheet; and (4) compare CALIOP-derived smoke plume injection to CMAQ modeled smoke plume injection. These results have the potential to provide value to national and international modeling communities (scientific and air quality) and to public land, fire, and air quality management and regulations communities.

Is the track of the Yellowstone hotspot driven by a deep mantle plume? - Review of volcanism, faulting, and uplift in light of new data

USGS Publications Warehouse

Pierce, K.L.; Morgan, L.A.

2009-01-01

Geophysical imaging of a tilted mantle plume extending at least 500??km beneath the Yellowstone caldera provides compelling support for a plume origin of the entire Yellowstone hotspot track back to its inception at 17??Ma with eruptions of flood basalts and rhyolite. The widespread volcanism, combined with a large volume of buoyant asthenosphere, supports a plume head as an initial phase. Estimates of the diameter of the plume head suggest it completely spanned the upper mantle and was fed from sources beneath the transition zone, We consider a mantle-plume depth to at least 1,000 km to best explain the large scale of features associated with the hotspot track. The Columbia River-Steens flood basalts form a northward-migrating succession consistent with the outward spreading of a plume head beneath the lithosphere. The northern part of the inferred plume head spread (pancaked) upward beneath Mesozoic oceanic crust to produce flood basalts, whereas basalt melt from the southern part intercepted and melted Paleozoic and older crust to produce rhyolite from 17 to 14??Ma. The plume head overlapped the craton margin as defined by strontium isotopes; westward motion of the North American plate has likely "scraped off" the head from the plume tail. Flood basalt chemistries are explained by delamination of the lithosphere where the plume head intersected this cratonic margin. Before reaching the lithosphere, the rising plume head apparently intercepted the east-dipping Juan de Fuca slab and was deflected ~ 250??km to the west; the plume head eventually broke through the slab, leaving an abruptly truncated slab. Westward deflection of the plume head can explain the anomalously rapid hotspot movement of 62??km/m.y. from 17 to 10??Ma, compared to the rate of ~ 25??km/m.y. from 10 to 2??Ma. A plume head-to-tail transition occurred in the 14-to-10-Ma interval in the central Snake River Plain and was characterized by frequent (every 200-300??ka for about 2??m.y. from 12.7 to 10.5??Ma) "large volume (> 7000??km3)", and high temperature rhyolitic eruptions (> 1000????C) along a ~ 200-km-wide east-west band. The broad transition area required a heat source of comparable area. Differing characteristics of the volcanic fields here may in part be due to variations in crustal composition but also may reflect development in differing parts of an evolving plume where the older fields may reflect the eruption from several volcanic centers located above very large and extensive rhyolitic magma chamber(s) over the detached plume head while the younger fields may signal the arrival of the plume tail intercepting and melting the lithosphere and generating a more focused rhyolitic magma chamber. The three youngest volcanic fields of the hotspot track started with large ignimbrite eruptions at 10.21, 6.62, and 2.05??Ma. They indicate hotspot migration N55?? E at ~ 25??km/m.y. compatible in direction and velocity with the North American Plate motion. The Yellowstone Crescent of High Terrain (YCHT) flares outward ahead of the volcanic progression in a pattern similar to a bow-wave, and thus favors a sub-lithospheric driver. Estimates of YCHT-uplift rates are between 0.1 and 0.4??mm/yr. Drainage divides have migrated northeastward with the hotspot. The Continental Divide and a radial drainage pattern now centers on the hotspot. The largest geoid anomaly in the conterminous U.S. is also centered on Yellowstone and, consistent with uplift above a mantle plume. Bands of late Cenozoic faulting extend south and west from Yellowstone. These bands are subdivided into belts based both on recency of offset and range-front height. Fault history within these belts suggests the following pattern: Belt I - starting activity but little accumulated offset; Belt II - peak activity with high total offset and activity younger than 14??ka; Belt III - waning activity with large offset and activity younger than 140??ka; and Belt IV - apparently dead on substanti

Mapping methane plumes and the delta C-13 composition of anthropogenic sources in southwest Germany

NASA Astrophysics Data System (ADS)

Schmidt, Martina; Yeman, Christiane; Dinger, Florian; Ars, Sebastien; Yver Kwok, Camille

2016-04-01

A mobile analyser based on Cavity-Ring-Down Spectroscopy was installed on a vehicle, together with a GPS receiver. This allows us to measure atmospheric methane and carbon dioxide mole fractions and the C-13 isotopes of both gases while driving. Methane mole fraction measurements show a good repeatability even for high frequency measurements whereas the 13CH4 measurements need a longer averaging time of 1 minute for 1 ‰ repeatability and 15 minutes for 0.23 ‰ repeatability. Driving through an emission plume, the signal is typically only 60 seconds long. To overcome the precision problem for the isotope measurements we filled a 25 m tubing when driving through the plume, which was then flushed back through our analyser during 30 minutes. During several campaigns we visited a land fill site, a biogas plant, a dairy cow farm and a natural gas storage and measured an averaged isotopic methane signature(C-13) of -58.3 ±3 ‰, -62.5 ± 1‰, -62.2 ± 2‰, -51 ± 7‰, respectively.

Femtosecond ablation applied to deep-drilling of hard metals

NASA Astrophysics Data System (ADS)

Bruneau, Sebastien; Hermann, Joerg; Dumitru, Gabriel; Sentis, Marc L.

2004-09-01

Mechanisms responsible for the limitation of the aspect ratio obtained by deep drilling of hard metals are investigated in the present work. Cemented carbide targets have been irradiated with laser pulses of 100 fs duration and 100 μJ maximum energy delivered by a Ti:sapphire laser system. The experiments are carried out in different gas environments (vacuum, air, helium up to atmospheric pressure) with incident laser fluences ranging from 1 to 20 Jcm-2. During deep drilling, the laser-induced ablation plume is characterized by means of in-situ plasma diagnostics. Fast imaging is used to observe the expansion behavior of the plasma plume whereas time- and space-resolved emission spectroscopy is employed to analyze the plasma composition. After irradiation, the laser-produced craters were examined by optical microscopy. A correlation between the ablation plume characteristics and the morphological changes of the mciro-holes is established. The results indicate that nanoclusters, that present a significant part of the ablated material, are responsbile for the alteration of the crater shape in the high laser fluence regime.

The Initial Development of Transient Volcanic Plumes as a Function of Source Conditions

NASA Astrophysics Data System (ADS)

Tournigand, Pierre-Yves; Taddeucci, Jacopo; Gaudin, Damien; Peña Fernández, Juan José; Del Bello, Elisabetta; Scarlato, Piergiorgio; Kueppers, Ulrich; Sesterhenn, Jörn; Yokoo, Akihiko

2017-12-01

Transient volcanic plumes, having similar eruption duration and rise timescales, characterize many unsteady Strombolian to Vulcanian eruptions. Despite being more common, such plumes are less studied than their steady state counterpart from stronger eruptions. Here we investigate the initial dynamics of transient volcanic plumes using high-speed (visible light and thermal) and high-resolution (visible light) videos from Strombolian to Vulcanian eruptions of Stromboli (Italy), Fuego (Guatemala), and Sakurajima (Japan) volcanoes. Physical parameterization of the plumes has been performed by defining their front velocity, velocity field, volume, and apparent surface temperature. We also characterized the ejection of the gas-pyroclast mixture at the vent, in terms of number, location, duration, and frequency of individual ejection pulses and of time-resolved mass eruption rate of the ejecta's ash fraction. Front velocity evolves along two distinct trends related to the initial gas-thrust phase and later buoyant phase. Plumes' velocity field, obtained via optical flow analysis, highlights different features, including initial jets and the formation and/or merging of ring vortexes at different scales. Plume volume increases over time following a power law trend common to all volcanoes and affected by discharge history at the vent. Time-resolved ash eruption rates range between 102 and 107 kg/s and may vary up to 2 orders of magnitude within the first seconds of eruption. Our results help detailing how the number, location, angle, duration, velocity, and time interval between ejection pulses at the vents crucially control the initial (first tens of second), and possibly later, evolution of transient volcanic plumes.

Explosive Volcanic Eruptions from Linear Vents on Earth, Venus and Mars: Comparisons with Circular Vent Eruptions

NASA Technical Reports Server (NTRS)

Glaze, Lori S.; Baloga, Stephen M.; Wimert, Jesse

2010-01-01

Conditions required to support buoyant convective plumes are investigated for explosive volcanic eruptions from circular and linear vents on Earth, Venus, and Mars. Vent geometry (linear versus circular) plays a significant role in the ability of an explosive eruption to sustain a buoyant plume. On Earth, linear and circular vent eruptions are both capable of driving buoyant plumes to equivalent maximum rise heights, however, linear vent plumes are more sensitive to vent size. For analogous mass eruption rates, linear vent plumes surpass circular vent plumes in entrainment efficiency approximately when L(sub o) > 3r(sub o) owing to the larger entrainment area relative to the control volume. Relative to circular vents, linear vents on Venus favor column collapse and the formation of pyroclastic flows because the range of conditions required to establish and sustain buoyancy is narrow. When buoyancy can be sustained, however, maximum plume heights exceed those from circular vents. For current atmospheric conditions on Mars, linear vent eruptions are capable of injecting volcanic material slightly higher than analogous circular vent eruptions. However, both geometries are more likely to produce pyroclastic fountains, as opposed to convective plumes, owing to the low density atmosphere. Due to the atmospheric density profile and water content on Earth, explosive eruptions enjoy favorable conditions for producing sustained buoyant columns, while pyroclastic flows would be relatively more prevalent on Venus and Mars. These results have implications for the injection and dispersal of particulates into the planetary atmosphere and the ability to interpret the geologic record of planetary volcanism.

Two global data sets of daily fire emission injection heights since 2003

NASA Astrophysics Data System (ADS)

Rémy, Samuel; Veira, Andreas; Paugam, Ronan; Sofiev, Mikhail; Kaiser, Johannes W.; Marenco, Franco; Burton, Sharon P.; Benedetti, Angela; Engelen, Richard J.; Ferrare, Richard; Hair, Jonathan W.

2017-02-01

The Global Fire Assimilation System (GFAS) assimilates fire radiative power (FRP) observations from satellite-based sensors to produce daily estimates of biomass burning emissions. It has been extended to include information about injection heights derived from fire observations and meteorological information from the operational weather forecasts of ECMWF. Injection heights are provided by two distinct methods: the Integrated Monitoring and Modelling System for wildland fires (IS4FIRES) parameterisation and the one-dimensional plume rise model (PRM). A global database of daily biomass burning emissions and injection heights at 0.1° resolution has been produced for 2003-2015 and is continuously extended in near-real time with the operational GFAS service of the Copernicus Atmospheric Monitoring Service (CAMS). In this study, the two injection height data sets were compared with the new MPHP2 (MISR Plume Height Project 2) satellite-based plume height retrievals. The IS4FIRES parameterisation showed a better overall agreement than the observations, while the PRM was better at capturing the variability of injection heights. The performance of both parameterisations is also dependent on the type of vegetation. Furthermore, the use of biomass burning emission heights from GFAS in atmospheric composition forecasts was assessed in two case studies: the South AMerican Biomass Burning Analysis (SAMBBA) campaign which took place in September 2012 in Brazil, and a series of large fire events in the western USA in August 2013. For these case studies, forecasts of biomass burning aerosol species by the Composition Integrated Forecasting System (C-IFS) of CAMS were found to better reproduce the observed vertical distribution when using PRM injection heights from GFAS compared to aerosols emissions being prescribed at the surface. The globally available GFAS injection heights introduced and evaluated in this study provide a comprehensive data set for future fire and atmospheric composition modelling studies.

Io's Kanehekili Hemisphere

NASA Technical Reports Server (NTRS)

1997-01-01

This color composite of Io, acquired by Galileo during its ninth orbit (C9) of Jupiter, shows the hemisphere of Io which is centered at longitude 52 degrees. The dark feature just to the lower right of the center of the disk is called Kanehekili. Named after an Hawaiian thunder god, Kanehekili contains two persistent high temperature hot spots and a 'new' active volcanic plume. NASA's Voyager spacecraft returned images of nine active plumes during its 1979 flyby of this dynamic satellite. To date, Galileo's plume monitoring observations have shown continued activity at four of those nine plume locations as well as new activity at six other locations.

North is to the top of the picture which combines images acquired using violet, green, and near-infrared (756 micrometers) filters. The resolution is 21 kilometers per picture element. The images were taken on June 27, 1997 at a range of 1,033,000 kilometers by the solid state imaging (CCD) system on NASA's Galileo spacecraft.

The Jet Propulsion Laboratory, Pasadena, CA manages the mission for NASA's Office of Space Science, Washington, DC.

This image and other images and data received from Galileo are posted on the World Wide Web, on the Galileo mission home page at URL http://galileo.jpl.nasa.gov. Background information and educational context for the images can be found at URL http://www.jpl.nasa.gov/galileo/sepo

Interdisciplinary study of atmospheric processes and constituents of the mid-Atlantic coastal region.. [air pollution control studies in Virginia

NASA Technical Reports Server (NTRS)

Kindle, E. C.; Bandy, E. C.; Copeland, G.; Blais, R.; Levy, G.; Sonenshine, D.

1975-01-01

Past research projects for the year 1974-1975 are listed along with future research programs in the area of air pollution control, remote sensor analysis of smoke plumes, the biosphere component, and field experiments. A detailed budget analysis is presented. Attachments are included on the following topics: mapping forest vegetation with ERTS-1 MSS data and automatic data processing techniques, and use of LARS system for the quantitative determination of smoke plume lateral diffusion coefficients from ERTS images of Virginia.

An investigation of methods for injecting emissions from boreal wildfires using WRF-Chem during ARCTAS

NASA Astrophysics Data System (ADS)

Sessions, W. R.; Fuelberg, H. E.; Kahn, R. A.; Winker, D. M.

2010-11-01

The Weather Research and Forecasting Model (WRF) is considered a "next generation" mesoscale meteorology model. The inclusion of a chemistry module (WRF-Chem) allows transport simulations of chemical and aerosol species such as those observed during NASA's Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS) in 2008. The ARCTAS summer deployment phase during June and July coincided with large boreal wildfires in Saskatchewan and Eastern Russia. One of the most important aspects of simulating wildfire plume transport is the height at which emissions are injected. WRF-Chem contains an integrated one-dimensional plume rise model to determine the appropriate injection layer. The plume rise model accounts for thermal buoyancy associated with fires and the local atmospheric stability. This study compares results from the plume model against those of two more traditional injection methods: Injecting within the planetary boundary layer, and in a layer 3-5 km above ground level. Fire locations are satellite derived from the GOES Wildfire Automated Biomass Burning Algorithm (WF_ABBA) and the MODIS thermal hotspot detection. Two methods for preprocessing these fire data are compared: The prep_chem_sources method included with WRF-Chem, and the Naval Research Laboratory's Fire Locating and Monitoring of Burning Emissions (FLAMBE). Results from the simulations are compared with satellite-derived products from the AIRS, MISR and CALIOP sensors. Results show that the FLAMBE pre-processor produces more realistic injection heights than does prep_chem_sources. The plume rise model using FLAMBE provides the best agreement with satellite-observed injection heights. Conversely, when the planetary boundary layer or the 3-5 km AGL layer were filled with emissions, the resulting injection heights exhibit less agreement with observed plume heights. Results indicate that differences in injection heights produce different transport pathways. These differences are especially pronounced in areas of strong vertical wind shear and when the integration period is long.

How do the optical properties of Asian aerosols change when they cross the Pacific?

NASA Astrophysics Data System (ADS)

Fischer, E. V.; Jaffe, D. A.

2009-12-01

Primary and secondary aerosols from Asia may have important climate implications. These aerosols are emitted locally, but can then be lofted into the free troposphere and advected across the Pacific. In this analysis we used observations from the Mount Bachelor Observatory (MBO) in conjunction with satellite data to identify the dominant aerosol types in specific Asian plumes that crossed the Pacific. In situ data from MBO is used to understand the observed changes in radiative properties. A suite of gas phase and aerosol measurements were made during spring 2008 and spring 2009 at MBO (2763 masl), located in central Oregon. Here we focus on observations of dry sub-μm aerosol scattering (σsp) and absorption (σap), made with an integrating nephelometer and a particle soot absorption photometer (PSAP). Using a combination of backward trajectory calculations and satellite observations, we identified 7 well defined plumes of Asian origin. These plumes included the highest σsp (34.8 Mm-1 hourly average) and σap (4.8 Mm-1 hourly average) observed at MBO over the 2008 and 2009 spring campaigns. Of interest in this analysis is 1) whether the intensive optical properties differ between these 7 Asian events, 2) whether these differences can be linked to differences in composition, and 3) whether the intensive optical properties differ from those observed closer to the Asian source region. Preliminary results show that the plumes clustered in terms of their optical properties; plumes hypothesized to contain a large fraction of mineral dust were the most distinct. We also observed larger variability in the average scattering Ångstrom exponent of the plumes and a higher average single scatter albedo than observations closer to the Asian coast. This work will be extended to compare observations at MBO with the most recent observations from Asia as they become available.

Petrology and geochemistry of mafic magmatic rocks from the Sarve-Abad ophiolites (Kurdistan region, Iran): Evidence for interaction between MORB-type asthenosphere and OIB-type components in the southern Neo-Tethys Ocean

NASA Astrophysics Data System (ADS)

Saccani, Emilio; Allahyari, Khalil; Rahimzadeh, Bahman

2014-05-01

The Sarve-Abad (Sawlava) ophiolites crop out in the Main Zagros Thrust Zone and represent remnants of the Mesozoic southern Neo-Tethys Ocean that was located between the Arabian shield and Sanandaj-Sirjan continental block. They consist of several incomplete ophiolitic sequences including gabbroic bodies, a dyke complex, and pillow lava sequences. These rocks generally range from sub-alkaline to transitional character. Mineral chemistry and whole-rock geochemistry indicate that they have compositions akin to enriched-type mid-ocean ridge basalts (E-MORB) and plume-type MORB (P-MORB). Nonetheless, the different depletion degrees in heavy rare earth elements (HREE), which can be observed in both E-MORB like and P-MORB like rocks enable two main basic chemical types of rocks to be distinguished as Type-I and Type-II. Type-I rocks are strongly depleted in HREE (YbN < ~ 6), whereas Type-II rocks are moderately depleted in HREE (YbN > 9.0). Petrogenetic modeling shows that Type-I rocks originated from 7 to 16% polybaric partial melting of a MORB-type mantle source, which was significantly enriched by plume-type components. These rocks resulted from the mixing of variable fractions of melts generated in garnet-facies and the spinel-facies mantle. In contrast, Type-II rocks originated from 5 to 8% partial melting in the spinel-facies of a MORB-type source, which was moderately enriched by plume-type components. A possible tectono-magmatic model for the generation of the southern Neo-Tethys oceanic crust implies that the continental rift and subsequent oceanic spreading were associated with uprising of MORB-type asthenospheric mantle featuring plume-type component influences decreasing from deep to shallow mantle levels. These deep plume-type components were most likely inherited from Carboniferous mantle plume activity that was associated with the opening of Paleo-Tethys in the same area.

Do plumes exist beneath Northwest Kyushu southwest Japan?

NASA Astrophysics Data System (ADS)

Mashima, H.

2014-12-01

A thermal plume model was proposed for the Hot-spot type volcanism at Northwest Kyushu, southwest Japan in the post period of opening of the Sea of Japan. The model regards the Northwest Kyushu Basalts (NWKBs) were magmas fractionated from parental magmas with MgO = 12.8 - 18.8 wt. %, indicating that partial melting occurred at temperatures from 1330 to 1500 °C and at pressures from 1.5 to 3.0 GPa (Sakuyama et al., 2009; 2014). Previous petrological and observations, however, indicate that the NWKBs separated from the source mantle at pressures shallower than those inferred from the plume model. The Mg-Fe-Ni compositions of some NWKBs suggest that they could have been in equilibrium with mantle olivines with Fo = 81 - 87, meaning that they would have been not fractionated but primitive magmas. The NWKBs are associated with primitive high magnesium andesites, indicating that partial melting continued at low pressure such as 0.5 GPa (Mashima, 2009a, b). NWKBs include not garnet lherzolite xenoliths but spinel lherzolite, showing that primitive melt separation occurred at pressure lower than 2GPa (Arai et al., 2001). These lines of evidence indicate that the separation of primitive NWKBs occurred at temperature up to 1250　°C and pressures from 0.5 to 1.5 GPa, significantly lower than those assumed by the plume model. Instead of the plume model, geology of NW Kyushu infers that the volcanism was a consequence of the tectonic evolution of NW Kyushu. The volcanism was leaks of asthenosphere thickened extensional tectonics from the Paleogene to the early Miocene. Orientations of NWKB dikes indicate their eruption was induced by the reactivation of preexisting faults under horizontal compressive stress field oriented to a NW-SE direction. This　horizontally compressive stress field would have been caused by mechanical interactions between the subducting Philippine Sea pate and the Eurasian Plate. The NW Kyushu volcanism could be explained in the context of plate tectonics without the plume hypothesis.

Agricultural Fires in the Southeastern U.S. During SEAC4RS: Emissions of Trace Gases and Particles and Evolution of Ozone, Reactive Nitrogen, and Organic Aerosol

NASA Technical Reports Server (NTRS)

Liu, X.; Zhang, Y.; Huey, L. G.; Yokelson, R. J.; Wang, Y.; Jimenez, J. L.; Campuzano-Jost, P.; Beyersdorf, A. J.; Blake, D. R.; Choi, Y.;

Biodegradation: Updating the concepts of control for microbial cleanup in contaminated aquifers.

PubMed

Meckenstock, Rainer U; Elsner, Martin; Griebler, Christian; Lueders, Tillmann; Stumpp, Christine; Aamand, Jens; Agathos, Spiros N; Albrechtsen, Hans-Jørgen; Bastiaens, Leen; Bjerg, Poul L; Boon, Nico; Dejonghe, Winnie; Huang, Wei E; Schmidt, Susanne I; Smolders, Erik; Sørensen, Sebastian R; Springael, Dirk; van Breukelen, Boris M

2015-06-16

Biodegradation is one of the most favored and sustainable means of removing organic pollutants from contaminated aquifers but the major steering factors are still surprisingly poorly understood. Growing evidence questions some of the established concepts for control of biodegradation. Here, we critically discuss classical concepts such as the thermodynamic redox zonation, or the use of steady state transport scenarios for assessing biodegradation rates. Furthermore, we discuss if the absence of specific degrader populations can explain poor biodegradation. We propose updated perspectives on the controls of biodegradation in contaminant plumes. These include the plume fringe concept, transport limitations, and transient conditions as currently underestimated processes affecting biodegradation.

CFD Simulation of the Space Shuttle Launch Vehicle with Booster Separation Motor and Reaction Control System Plumes

NASA Technical Reports Server (NTRS)

Gea, L. M.; Vicker, D.

2006-01-01

The primary objective of this paper is to demonstrate the capability of computational fluid dynamics (CFD) to simulate a very complicated flow field encountered during the space shuttle ascent. The flow field features nozzle plumes from booster separation motor (BSM) and reaction control system (RCS) jets with a supersonic incoming cross flow at speed of Mach 4. The overset Navier-Stokes code OVERFLOW, was used to simulate the flow field surrounding the entire space shuttle launch vehicle (SSLV) with high geometric fidelity. The variable gamma option was chosen due to the high temperature nature of nozzle flows and different plume species. CFD predicted Mach contours are in good agreement with the schlieren photos from wind tunnel test. Flow fields are discussed in detail and the results are used to support the debris analysis for the space shuttle Return To Flight (RTF) task.

CFD Simulation of the Space Shuttle Launch Vehicle with Booster Separation Motor and Reaction Control Plumes

NASA Technical Reports Server (NTRS)

Gea, L. M.; Vicker, D.

2006-01-01

The primary objective of this paper is to demonstrate the capability of computational fluid dynamics (CFD) to simulate a very complicated flow field encountered during the space shuttle ascent. The flow field features nozzle plumes from booster separation motor (BSM) and reaction control system (RCS) jets with a supersonic incoming cross flow at speed of Mach 4. The overset Navier-Stokes code OVERFLOW, was used to simulate the flow field surrounding the entire space shuttle launch vehicle (SSLV) with high geometric fidelity. The variable gamma option was chosen due to the high temperature nature of nozzle flows and different plume species. CFD predicted Mach contours are in good agreement with the schlieren photos from wind tunnel test. Flow fields are discussed in detail and the results are used to support the debris analysis for the space shuttle Return To Flight (RTF) task.

The Possibility of Serpentinization on Enceladus

NASA Astrophysics Data System (ADS)

Boye Nissen, Silas; Taubner, Ruth-Sophie; Leitner, Johannes J.; Firneis, Maria G.

2015-04-01

Enceladus, an icy moon of Saturn, is considered a potential place for a second genesis of life in a rather easy accessible environment for future space missions. Plumes erupting material out to Saturn's E-ring have been detected. This and the latest gravity data received by NASA's Cassini probe highly suggest a regional subsurface water reservoir to exist. The Cassini mission has detected all the necessary elements for life in these plumes and few ecosystems known from the Earth could in theory exist on this moon. These ecosystems rely on a sufficient hydrogen source. On Earth, this molecule is known to be produced when the oceans interact with silicates in the mantle through a geochemical process called serpentinization. The aim of this work is first of all to determine whether serpentinization is possible on Enceladus at an assumed pressure range of 25-50 bars and a temperature range of 0-50 °C. If it is possible, then the second aim is to estimate the hydrogen production rate. Therefore, geochemical modeling with the EQ3/6 software package has been applied and thermody-namic databases have been created with the use of the DBCreate program. Due to the present lack of data on the chemical composition of the subsurface sea it is assumed to be equal to the chemical composition of the plumes. Finally, the importance of the pH value (7-9) is studied. Models based on Enceladus being a captured comet or aggregated ring material are used to specify the core composition. These are different combinations of pyroxenes and olivines or no silicates, respectively. The results show that serpentinization is ongoing in all models with silicates at these low pressure and temperature ranges. Hydrogen is only produced in the presence of an iron-rich end-member of either pyroxene (ferrosilite) or olivine (fayalite). In these cases, the dihydrogen concentration is estimated to be around 2.0 mg/kg solution. Changing the pH value did not make any differences to the results. It is discussed how the complex aqueous solution assumed (based on the composition of the plumes) affect the serpentinization process on Enceladus. In addition, it is discussed if the pressure and temperature ranges are too small to make a significant change on the dihydrogen concentration. This work shows that serpentinization seems to be possible at the low pressure and temperature values found at the water/rock boundary on Enceladus. To improve the estimate of the hydrogen production rate, measurements for the silicate ions in the aqueous solution on Enceladus are needed. We would like to thank Wolfgang Bach from the Research Group "Petrology of the Ocean Crust" (University of Bremen) for his very helpful support on applying the geochemical modeling software.

Spatial and temporal characterization of methane plumes from mobile platforms

NASA Astrophysics Data System (ADS)

O'Brien, A.; Wendt, L.; Miller, D. J.; Lary, D. J.; Zondlo, M. A.

2013-12-01

The spatial and temporal characterization of methane plumes from hydraulic fracturing well sites are presented. Methane measurements from the Marcellus shale region obtained using a commercial instrument on a motor vehicle are discussed. Over 100 well sites in the region were sampled and the methane signature in the vicinity of these wells is presented. Additionally, measurements of methane from our open-path instrument flown aboard the UT Dallas AMR Payload Master 100 remote-controlled, electric aircraft in the Barnett shale region are presented. Using our observations of aircraft surveys near well sites and a gaussian plume dispersion model emission estimates of fugitive methane are presented.

Remote sensing operations (multispectral scanner and photographic) in the New York Bight, 22 September 1975

NASA Technical Reports Server (NTRS)

Johnson, R. W.; Hall, J. B., Jr.

1977-01-01

Ocean dumping of waste materials is a significant environmental concern in the New York Bight. One of these waste materials, sewage sludge, was monitored in an experiment conducted in the New York Bight on September 22, 1975. Remote sensing over controlled sewage sludge dumping included an 11-band multispectral scanner, fiver multispectral cameras and one mapping camera. Concurrent in situ water samples were taken and acoustical measurements were made of the sewage sludge plumes. Data were obtained for sewage sludge plumes resulting from line (moving barge) and spot (stationary barge) dumps. Multiple aircraft overpasses were made to evaluate temporal effects on the plume signature.

Mantle source heterogeneity of the Early Jurassic basalt of eastern North America

NASA Astrophysics Data System (ADS)

Gregory Shellnutt, J.; Dostal, Jaroslav; Yeh, Meng-Wan

2018-04-01

One of the defining characteristics of the basaltic rocks from the Early Jurassic Eastern North America (ENA) sub-province of the Central Atlantic Magmatic Province (CAMP) is the systematic compositional variation from South to North. Moreover, the tectono-thermal regime of the CAMP is debated as it demonstrates geological and structural characteristics (size, radial dyke pattern) that are commonly associated with mantle plume-derived mafic continental large igneous provinces but is considered to be unrelated to a plume. Mantle potential temperature ( T P) estimates of the northern-most CAMP flood basalts (North Mountain basalt, Fundy Basin) indicate that they were likely produced under a thermal regime ( T P ≈ 1450 °C) that is closer to ambient mantle ( T P ≈ 1400 °C) conditions and are indistinguishable from other regions of the ENA sub-province ( T Psouth = 1320-1490 °C, T Pnorth = 1390-1480 °C). The regional mantle potential temperatures are consistent along the 3000-km-long ENA sub-province suggesting that the CAMP was unlikely to be generated by a mantle plume. Furthermore, the mantle potential temperature calculation using the rocks from the Northern Appalachians favors an Fe-rich mantle (FeOt = 8.6 wt %) source, whereas the rocks from the South Appalachians favor a less Fe-rich (FeOt = 8.3 wt %) source. The results indicate that the spatial-compositional variation of the ENA basaltic rocks is likely related to differing amounts of melting of mantle sources that reflect the uniqueness of their regional accreted terranes (Carolinia and West Avalonia) and their post-accretion, pre-rift structural histories.

The Evolution of Electrospray Generated Droplets is Not Affected by Ionization Mode

NASA Astrophysics Data System (ADS)

Liigand, Piia; Heering (Suu), Agnes; Kaupmees, Karl; Leito, Ivo; Girod, Marion; Antoine, Rodolphe; Kruve, Anneli

2017-10-01

Ionization efficiency and mechanism in ESI is strongly affected by the properties of mobile phase. The use of mobile-phase properties to accurately describe droplets in ESI source is convenient but may be inadequate as the composition of the droplets is changing in the plume due to electrochemical reactions occurring in the needle tip as well as continuous drying and fission of droplets. Presently, there is paucity of research on the effect of the polarity of the ESI mode on mobile phase composition in the droplets. In this paper, the change in the organic solvent content, pH, and droplet size are studied in the ESI plume in both ESI+ and ESI- ionization mode. We introduce a rigorous way - the absolute pH (pHabs H 2 O) - to describe pH change in the plume that takes into account organic solvent content in the mobile phase. pHabs H 2 O enables comparing acidities of ESI droplets with different organic solvent contents. The results are surprisingly similar for both ionization modes, indicating that the dynamics of the change of mobile-phase properties is independent from the ESI mode used. This allows us to conclude that the evolution of ESI droplets first of all proceeds via the evaporation of the organic modifier and to a lesser extent via fission of smaller droplets from parent droplets. Secondly, our study shows that qualitative findings related to the ESI process obtained on the ESI+ mode can almost directly be applied also in the ESI- mode. [Figure not available: see fulltext.

Recycling Seamounts: Implications for Mantle Source Heterogeneities

NASA Astrophysics Data System (ADS)

Madrigal, P.; Gazel, E.

2016-12-01

Isolated seamounts formed away from plate boundaries and/or known hotspot tracks are widely distributed in the Earth's oceanic plates. Despite their pervasiveness, the origin and composition of the magmatic sources that create these seamounts are still unknown. Moreover, as the seamount provinces travel along with the oceanic plate towards subduction trenches these volcanic edifices become subducted materials that are later recycled into the mantle. Using radiogenic isotopes (Sr-Nd-Pb) from present-day non-plume ocean island basalts (OIB) sampled by drilling and dredging as well as by normal processes of accretion to subduction margins, we modeled the isotopic evolution of these enriched reservoirs to assess their role as discrete components contributing to upper mantle heterogeneity. Our evidence suggests that a highly enriched mantle reservoir can originate from OIB-type subducted material that gets incorporated and stirred throughout the upper mantle in a shorter time period ( 200 Ma-500 Ma) than other highly enriched components like ancient subducted oceanic crust (>1 Ga), thought to be the forming agent of the HIMU mantle reservoir endmember. Enriched signatures from intraplate volcanism can be described by mixing of a depleted component like DMM and an enriched reservoir like non-plume related seamounts. Our data suggests that the isotopic evolution in time of a seamount-province type of reservoir can acquire sufficiently enriched compositions to resemble some of the most enriched magmas on Earth. This "fast-forming" (between 200 and 500 Ma) enriched reservoir could also explain some of the enriched signatures commonly present in intraplate and EMORB magmas unrelated to deep mantle plume upwellings.

V isotope composition in modern marine hydrothermal sediments

NASA Astrophysics Data System (ADS)

Wu, F.; Owens, J. D.; Nielsen, S.; German, C. R.; Rachel, M.

2017-12-01

Vanadium is multivalence transition metal with two isotopes (51V and 50V). Recent work has shown that large V isotope variations occur with oxygen variations in modern sediments (Wu et al., 2016 and 2017 Goldschmidt Abstracts), providing its potential as a promising proxy for determining low oxygen conditions. However, the development of V isotopes as a proxy to probe past redox conditions requires a comprehensive understanding of the modern oceanic isotopic mass balance. Therein, the scavenging of V from the hydrous iron oxides in hydrothermal fluid has been shown to be an important removal process from seawater (Rudnicki and Elderfield, 1993 GCA) but remains unquantified. In this study, we analyzed V isotopic compositions of metalliferous sediments around the active TAG hydrothermal mound from the mid-Atlantic Ridge (26° degrees North) and the Eastern Pacific Zonal Transect (GEOTRACES EPZT cruise GP16). The TAG sediments deposited as Fe oxyhydroxides from plume fall-out, and have δ51V values between -0.3 to 0‰. The good correlation between Fe and V for these metalliferous sediments indicate that the accumulation of V in these samples is directly related to the deposition of Fe oxyhydroxides, which also control their V isotope signature. The EPZT samples cover 8,000 km in the South Pacific Ocean with sedimentary areas that underlie the Peru upwelling region and the well-oxygenated deep South Pacific Ocean influenced by hydtorthermal plume material from southern East Pacific Rise (EPR). The sediments collected at the east of the EPR have δ51V values between -1.2 to -0.7‰, similar to previous δ51V of oxic sediments. In contrast, the sediments from the west of the EPR have δ51V values (-0.4 to 0‰) similar to hydrothermal sediments from the mid-Atlantic Ridge, indicating the long transportation (more than 4,000 km, Fitzsimmons et al., 2017 NG) of Fe and Mn from hydrothermal plume and their incorporation into sediments have a major impact on the cycle of V in the ocean. The fingerprint of δ51V between oxic sediments and hydrothermal flux are significantly different and should be easily discernible in the geologic record. Consequently, our results show that the removal of V from hydrothermal sediments has an important influence on the marine V cycle, which needs to be considered for future modern and paleoclimatic studies.

Investigation of characteristics and transformation processes of megacity emission plumes using a mobile laboratory in the Paris metropolitan area

NASA Astrophysics Data System (ADS)

von der Weiden-Reinmüller, S.-L.; Drewnick, F.; Zhang, Q.; Meleux, F.; Beekmann, M.; Borrmann, S.

2012-04-01

A growing fraction of the world's population is living in urban agglomerations of increasing size. Currently, 20 cities worldwide qualify as so-called megacities, having more than 10 million inhabitants. These intense pollution hot-spots cause a number of scientific questions concerning their influence on local and regional air quality, which is connected with human health, flora and fauna. In the framework of the European Union FP7 MEGAPOLI project (Megacities: Emissions, urban, regional and Global Atmospheric POLlution and climate effects, and Integrated tools for assessment and mitigation) two major field campaigns were carried out in the greater Paris region in July 2009 and January/February 2010. This work presents results from mobile particulate and gas phase measurements with focus on the characteristics of the Paris emission plume and its impact on the regional air quality and on aerosol transformation processes within this plume as it travels away from its source. In addition differences between summer and winter conditions are discussed. The mobile laboratory was equipped with high time resolution instrumentation to measure particle number concentrations (dP > 2.5 nm), size distributions (dP ~ 5 nm - 32 μm), sub-micron chemical composition (non-refractory species using Aerodyne HR-ToF-AMS, PAH and black carbon) as well as major trace gases (CO2, SO2, O3, NOx) and standard meteorological parameters. On-board webcam and GPS allow detailed monitoring of traffic situation and vehicle track. In a total of 29 mobile and 25 stationary measurements with the mobile laboratory the Paris emission plume as well as the atmospheric background was characterized under various meteorological conditions. This allows investigating the influence of external factors like temperature, solar radiation or precipitation on the plume characteristics. Three measurement strategies were applied to investigate the emission plume. First, circular mobile measurements around Paris provide cross sections through plume air masses as well as local background variation measurements. Second, radial measurement trips beginning near the outer area of the agglomeration extending up to ~200 km distance from Paris along the direction of the emission plume provide insight into the extension of the plume and transformation processes. Third, stationary measurements at different locations provide background as well as pollution measurements, especially if the wind direction is shifting, causing the plume to pass over the measurement site. During radial measurement trips the decrease in the concentrations of primary pollution marker species as hydrocarbon-like organic aerosol, black carbon, PAH and NOx with increasing distance from Paris is clearly observed. This decrease is mainly caused by dilution processes, but additional aging effects are also detectable. While entering the emission plume on cross section measurements a significant increase in such marker species compared to background values can be seen. On the other hand, overall statistics of both campaigns shows that day-to-day background variations influenced mainly by long range transported pollution (i.e. air mass origin) are stronger than variations between background and plume on specific days. A description of the methods developed for analysing the mobile data will complete this presentation.

In-Situ Observations of a Subglacial Outflow Plume in a Greenland Fjord

NASA Astrophysics Data System (ADS)

Mankoff, K. D.; Straneo, F.; Singh, H.; Das, S. B.

2014-12-01

We present oceanographic observations collected in and immediately outside of a buoyant, fresh, sediment-laden subglacial outflow plume rising up the marine-terminating front of Sarqardleq Glacier, Greenland (68.9 N, 50.4 W). Subglacial outflow plumes, associated with the discharge at depth of upstream glacial surface melt, entrain the relatively warm fjord waters and are correlated with enhanced submarine melt and increased calving. Few in-situ observations exist due to the challenges of making measurements at the calving front of glaciers. Our data were collected using a small boat, a helicopter, and a JetYak (a remote-controlled jet-ski-powered kayak). Temperature and salinity profiles in, around, and far from the plume are used to described its oceanographic properties, spatial extent, and temporal variability. This plume rises vertically up the ice front expanding laterally and away from the ice, over-shoots its stable isopycnal and reaches the surface. Its surface expression is identified by colder, saltier, sediment-laden water flowing at ~5 m/s away from the ice face. Within ~300 m from the ice it submerges as it seeks buoyant stability.

A Multitracer Approach to Detecting Wastewater Plumes from Municipal Injection Wells in Nearshore Marine Waters at Kihei and Lahaina, Maui, Hawaii

USGS Publications Warehouse

Hunt, Charles D.; Rosa, Sarah N.

2009-01-01

Municipal wastewater plumes discharging from aquifer to ocean were detected by nearshore wading surveys at Kihei and Lahaina, on the island of Maui in Hawaii. Developed in cooperation with the Hawaii State Department of Health, the survey methodology included instrument trolling to detect submarine groundwater discharge, followed by analysis of water and macroalgae for a suite of chemical and isotopic constituents that constitute a 'multitracer' approach. Surveys were conducted May 6-28, 2008, during fair-weather conditions and included: (1) wading and kayak trolling with a multiparameter water-quality sonde, (2) marine water-column sampling, and (3) collection of benthic algae samples. Instrument trolling helped guide the water sampling strategy by providing dense, continuous transects of water properties on which groundwater discharge zones could be identified. Water and algae samples for costly chemical and isotopic laboratory analyses were last to be collected but were highly diagnostic of wastewater presence and nutrient origin because of low detection levels and confirmation across multiple tracers. Laboratory results confirmed the presence of wastewater constituents in marine water-column samples at both locales and showed evidence of modifying processes such as denitrification and mixing of effluent with surrounding groundwater and seawater. Carbamazepine was the most diagnostic pharmaceutical, detected in several marine water-column samples and effluent at both Kihei and Lahaina. Heavy nitrogen-isotope compositions in water and algae were highly diagnostic of effluent, particularly where enriched to even heavier values than effluent source compositions by denitrification. Algae provided an added advantage of time-integrating their nitrogen source during growth. The measured Kihei plume coincided almost exactly with prior model predictions, but the Lahaina plume was detected well south of the expected direct path from injection wells to shore and may be guided by a buried valley fill from an ancestral course of Honokowai Stream. Nutrient concentrations in upland wells at Lahaina were comparable to concentrations in wastewater but originate instead from agricultural fertilizers. A key factor in detecting and mapping the wastewater plumes was sampling very close to shore (mostly within 20 m or so) and in very shallow water (mostly 0.5 to 2 m depth). Effluent probably discharges somewhat offshore as well, although prior attempts to detect an injected fluorescent tracer at Lahaina in the 1990s were inconclusive, having focused farther offshore in water mostly 10-30 m deep. Sampling of benthic porewater and algae would offer the best chances for further effluent detection and mapping offshore, and sampling of onland monitor wells could provide additional understanding of geochemical processes that take place in the effluent plumes and bring about some degree of natural attenuation of nutrients.

In situ study of the factors controlling Fe, Cu and Zn scavenging during the early mixing between hydrothermal fluids and seawater

NASA Astrophysics Data System (ADS)

Cathalot, C.; Laes-Huon, A.; Pelleter, E.; Maillard, L.; Chéron, S.; Boissier, A.; Waeles, M.; Cotte, L.; Pernet-Coudrier, B.; Gayet, N.; Sarrazin, J.; Sarradin, P. M.

2016-12-01

Despite the importance of trace metals for marine ecosystems and in the global carbon cycle, dissolved metal sources in the deep ocean and their export mechanism are, today, still unconstrained. The historical view that dissolved metals are largely removed from hydrothermal plumes through precipitation of a range of iron-bearing minerals is now being challenged. Several potential mechanisms for the delivery of hydrothermally sourced metals to the open ocean have been suggested and require a thorough documentation of the early mixing processes between the hydrothermal fluids and the ambient seawater. The geochemistry of a plume, and specially the rising plume, is dictated by the nature and composition of the host rock, fluid temperature, phase separation at depth and subsurface mixing processes, and thus can vary in temperature, pH, metal and dissolved gases content between spatially close hydrothermal vents. Here, we present in situ chemical conditions during the early mixing gradient between hydrothermal fluids and seawater at the Lucky Strike site (Mid-Atlantic Ridge), using a multi proxy approach targeting both the dissolved and particulate phase and combining in situ measurements and analysis back in the lab. Indeed, in situ O2, H2S and temperature measurements were performed at a 1Hz frequency, coupled to lower frequency analysis of in situ Fe2+. In addition, particulate material filtered in situ was analyzed using Inductive Coupled Plasma - Mass Spectrometry, X-Ray Diffraction, X-Ray Fluorescence and Scanning Electron Microscopy and provided useful insights regarding the reactivity of metals during the mixing processes. Our results show different behavior within the Lucky Strike vent field. Fe and S co-precipitation through chalcopyrite formation at the newly discovered Capelinhos site seem to be the main process. At the White Caste site, on the other hand, wurzite and sphalerite precipitation seems to dominate the dilution processes, H2S being rapidly titrated with the available Zinc early in the mixing. Our results indicate a clear control by subsurface mixing processes, at a very local scale: within a single vent field, temperature outflow of the hydrothermal fluid clearly drives Cu, Fe and Zn scavenging in the particulate phase, and controlling hence the iron stability and export.

Fringe-controlled biodegradation under dynamic conditions: quasi 2-D flow-through experiments and reactive-transport modeling.

PubMed

Eckert, Dominik; Kürzinger, Petra; Bauer, Robert; Griebler, Christian; Cirpka, Olaf A

2015-01-01

Biodegradation in contaminated aquifers has been shown to be most pronounced at the fringe of contaminant plumes, where mixing of contaminated water and ambient groundwater, containing dissolved electron acceptors, stimulates microbial activity. While physical mixing of contaminant and electron acceptor by transverse dispersion has been shown to be the major bottleneck for biodegradation in steady-state plumes, so far little is known on the effect of flow and transport dynamics (caused, e.g., by a seasonally fluctuating groundwater table) on biodegradation in these systems. Towards this end we performed experiments in quasi-two-dimensional flow-through microcosms on aerobic toluene degradation by Pseudomonas putida F1. Plume dynamics were simulated by vertical alteration of the toluene plume position and experimental results were analyzed by reactive-transport modeling. We found that, even after disappearance of the toluene plume for two weeks, the majority of microorganisms stayed attached to the sediment and regained their full biodegradation potential within two days after reappearance of the toluene plume. Our results underline that besides microbial growth, also maintenance and dormancy are important processes that affect biodegradation performance under transient environmental conditions and therefore deserve increased consideration in future reactive-transport modeling. Copyright © 2014 Elsevier B.V. All rights reserved.

On the Vertical Nature of Biomass Burning Plumes by the California Coast and Their Relationship with Marine Boundary Layer Clouds

NASA Astrophysics Data System (ADS)

Hu, L.; Montzka, S. A.; Godwin, D.; Andrews, A. E.; Thoning, K. W.; Miller, B. R.; Sweeney, C.; Miller, J. B.; Lehman, S.; Siso, C.; Mondeel, D. J.; Hall, B. D.; Nance, J. D.; Tans, P. P.; Elkins, J. W.

2016-12-01

Biomass burning (BB) plumes can significantly impact stratocumulus clouds (Sc), the dominant cloud type by global area, by altering their microphysical properties. The California (CA) coast is home to one of the three major semi-permanent stratocumulus (Sc) cloud decks in the world and BB emissions are of growing concern in the western United States, owing to both a warmer climate and fire-control strategies over recent decades. The thickness and vertical position of BB plumes, especially relative to clouds, is critical to understand how the aerosol will affect the thermodynamic structure of the atmosphere, cloud properties, and radiative forcing. This study reports on the characterization of the vertical, spatial, and temporal nature of BB aerosol over coastal CA, based on airborne data collected in the months of July and August for 2013 and 2016. Results from over 100 soundings indicate that multiple BB plume layers exist above clouds, with the thickness of BB plumes and their vertical position relative to cloud top varying significantly as a function of distance from coastline. Comparison of soundings at a given location at two different times of day reveals significant variation in BB characteristics. Intercomparisons for BB plume characteristics are explored between the field data, NAAPS, and CALIPSO.

On the Vertical Nature of Biomass Burning Plumes by the California Coast and Their Relationship with Marine Boundary Layer Clouds

NASA Astrophysics Data System (ADS)

Hossein Mardi, A.; MacDonald, A. B.; Dadashazar, H.; Crosbie, E.; WANG, Z.; Lynch, P.; Campbell, J. R.; Jonsson, H.; Sorooshian, A.

2017-12-01

Biomass burning (BB) plumes can significantly impact stratocumulus clouds (Sc), the dominant cloud type by global area, by altering their microphysical properties. The California (CA) coast is home to one of the three major semi-permanent stratocumulus (Sc) cloud decks in the world and BB emissions are of growing concern in the western United States, owing to both a warmer climate and fire-control strategies over recent decades. The thickness and vertical position of BB plumes, especially relative to clouds, is critical to understand how the aerosol will affect the thermodynamic structure of the atmosphere, cloud properties, and radiative forcing. This study reports on the characterization of the vertical, spatial, and temporal nature of BB aerosol over coastal CA, based on airborne data collected in the months of July and August for 2013 and 2016. Results from over 100 soundings indicate that multiple BB plume layers exist above clouds, with the thickness of BB plumes and their vertical position relative to cloud top varying significantly as a function of distance from coastline. Comparison of soundings at a given location at two different times of day reveals significant variation in BB characteristics. Intercomparisons for BB plume characteristics are explored between the field data, NAAPS, and CALIPSO.

ACE-FTS observations of pyrogenic trace species in boreal biomass burning plumes during BORTAS

NASA Astrophysics Data System (ADS)

Tereszchuk, K. A.; González Abad, G.; Clerbaux, C.; Hadji-Lazaro, J.; Hurtmans, D.; Coheur, P.-F.; Bernath, P. F.

2013-05-01

To further our understanding of the effects of biomass burning emissions on atmospheric composition, the BORTAS campaign (BOReal forest fires on Tropospheric oxidants over the Atlantic using Aircraft and Satellites) was conducted on 12 July to 3 August 2011 during the boreal forest fire season in Canada. The simultaneous aerial, ground and satellite measurement campaign sought to record instances of boreal biomass burning to measure the tropospheric volume mixing ratios (VMRs) of short- and long-lived trace molecular species from biomass burning emissions. The goal was to investigate the connection between the composition and the distribution of these pyrogenic outflows and their resulting perturbation to atmospheric chemistry, with particular focus on oxidant species to determine the overall impact on the oxidizing capacity of the free troposphere. Measurements of pyrogenic trace species in boreal biomass burning plumes were made by the Atmospheric Chemistry Experiment Fourier Transform Spectrometer (ACE-FTS) onboard the Canadian Space Agency (CSA) SCISAT-1 satellite during the BORTAS campaign. Even though biomass burning emissions are typically confined to the boundary layer, outflows are often injected into the upper troposphere by isolated convection and fire-related convective processes, thus allowing space-borne instruments to measure these pyrogenic outflows. An extensive set of 14 molecules - CH3OH, C2H2, C2H6, C3H6O, CO, HCN, HCOOH, HNO3, H2CO, NO, NO2, OCS, O3, and PAN - have been analysed. Included in this analysis is the calculation of age-dependent sets of enhancement ratios for each of the species originating from fires in North America (Canada, Alaska) and Siberia for a period of up to 7 days. Ratio values for the shorter lived primary pyrogenic species decrease over time primarily due to oxidation by the OH radical as the plume ages and values for longer lived species such as HCN and C2H6 remain relatively unchanged. Increasing negative values are observed for the oxidant species, including O3, indicating a destruction process in the plume as it ages such that concentrations of the oxidant species have dropped below their off-plume values. Results from previous campaigns have indicated that values for the molar ratios of ΔO3 /ΔO obtained from the measurements of the pyrogenic outflow from boreal fires are highly variable and range from negative to positive, irrespective of plume age. This variability has been attributed to pollution effects where the pyrogenic outflows have mixed with either local urban NOx emissions or pyrogenic emissions from the long-range transport of older plumes, thus affecting the production of O3 within the plumes. The results from this study have identified another potential cause of the variability in O3 concentrations observed in the measurements of biomass burning emissions, where evidence of stratosphere-troposphere exchange due to the pyroconvective updrafts from fires has been identified. Perturbations caused by the lofted emissions in these fire-aided convective processes may result in the intrusion of stratospheric air masses into the free troposphere and subsequent mixing of stratospheric O3 into the pyrogenic outflows causing fluctuations in observed ΔO3/ΔCO molar ratios.

Fractionation of families of major, minor, and trace metals across the melt-vapor interface in volcanic exhalations

USGS Publications Warehouse

Hinkley, T.K.; Le Cloarec, M.-F.; Lambert, G.

1994-01-01

Chemical families of metals fractionate systematically as they pass from a silicate melt across the interface with the vapor phase and on into a cooled volcanic plume. We measured three groups of metals in a small suite of samples collected on filters from the plumes of Kilauea (Hawaii, USA), Etna (Sicily), and Merapi (Java) volcanoes. These were the major, minor, and trace metals of the alkali and alkaline earth families (K, Rb, Cs, Ca, Sr, Ba), a group of ordinarily rare metals (Cd, Cu, In, Pb, Tl) that are related by their chalcophile affinities, and the radon daughter nuclides 210Po, 210Bi, and 210Pb. The measurements show the range and some details of systematic melt-vapor fractionation within and between these groups of metals. In the plumes of all three volcanoes, the alkali metals are much more abundant than the alkaline earth metals. In the Kilauea plume, the alkali metals are at least six times more abundant than the alkaline earth metals, relative to abundances in the melt; at Etna, the factor is at least 300. Fractionations within each family are, commonly, also distinctive; in the Kilauea plume, in addition to the whole alkaline earth family being depleted, the heaviest metals of the family (Sr, Ba) are progressively more depleted than the light metal Ca. In plumes of fumaroles at Merapi, K/Cs ratios were approximately three orders of magnitude smaller than found in other earth materials. This may represent the largest observed enrichment of the "light ion lithophile" (LIL) metals. Changes in metal ratios were seen through the time of eruption in the plumes of Kilauea and Etna. This may reflect degree of degassing of volatiles, with which metals complex, from the magma bodies. At Kilauea, the changes in fractionation were seen over about three years; fractionation within the alkaline earth family increased, and that between the two families decreased, over that time. All of the ordinarily rare chalcophile metals measured are extremely abundant in volcanic plumes, and Cd and Tl are enriched relative to the others. Indium is much more abundant in the plume of the hotspot volcano Kilauea than in the Etna plume (probably non-hotspot in character). It may be a useful indicator of the tapping of deep mantle zones, or could aid in the interpretation of reports of Pt group metals in exhalations from hot spot volcanoes. Indium in old glacial ice strata could help assess magnitude and variability of exhalations from hotspot volcanoes in past time. Strong melt-vapor fractionation of the alkali and alkaline earth metals may only be observed in plumes during quiescent degassing of volcanoes; when large amounts of ash or spatter (undifferentiated lava) enter the plume, its alkali and alkaline earth metal composition may approach that of the melt. Ratios among the chalcophile metals may not be much changed by addition of ash, because their concentrations in melt are so small, and masses of them in any plume may remain dominated by transfer across the melt-vapor interface. Radon daughter nuclides give information about state of volcanic activity at time of sampling. The precisely known origins, ultratrace detectability, decay systematics, and wide variations in volatility of these species provide information about residence times, degassing and travel histories, and identities of melt bodies in volcanic systems. ?? 1994.

[Simulation on contamination forecast and control of groundwater in a certain hazardous waste landfill].

PubMed

Ma, Zhi-Fei; An, Da; Jiang, Yong-Hai; Xi, Bei-Dou; Li, Ding-Long; Zhang, Jin-Bao; Yang, Yu

2012-01-01

On the basis of site investigation and data collection of a certain hazardous waste landfill, the groundwater flow and solute transport coupled models were established by applying Visual Modflow software, which was used to conduct a numerical simulation that forecast the transport process of Cr6+ in groundwater and the effects of three control measures (ground-harden, leakage-proof barriers and drainage ditches) of contaminants transport after leachate leakage happened in impermeable layer of the landfill. The results show that the contamination plume of Cr6+ transports with groundwater flow direction, the contamination rang would reach the pool's boundary in 10 years, and the distance of contamination transport is 1 450 m. But the diffusion range of contamination plume would not be obviously expanded between 10 and 20 years. While the ground is hardened, the contamination plume would not reach the pool's boundary in 20 years. When the leakage-proof barrier is set in the bottom of water table aquifer, the concentration of Cr6+ is higher than that the leakage-proof barrier is unset, but the result is just opposite when setting the leakage-proof barrier in the bottom of underlying aquifer. The range of contamination plume is effectively controlled by setting drainage ditches that water discharge is 2 642 m3 x d(-1), which makes the monitoring wells would not be contaminated in 20 years. Moreover, combining the ground-harden with drainage ditches can get the best effect in controlling contaminants diffusion, and meanwhile, the drainage ditches' daily discharge is reduced to 1 878 m3 x d(-1). Therefore, it is suggested that the control measure combining the ground-harden with drainage ditches should apply to prevent contamination diffusion in groundwater when leachate leakage have happened in impermeable layer of the landfill.

Dual polarisation C-band weather radar imagery of the 6 August 2012 Te Maari Eruption, Mount Tongariro, New Zealand

NASA Astrophysics Data System (ADS)

Crouch, John F.; Pardo, Natalia; Miller, Craig A.

2014-10-01

The 6 August 2012 eruption of Mt. Tongariro from Upper Te Maari Crater in the central North Island of New Zealand was the first volcanic eruption observed by an operational weather radar in New Zealand, and is believed to be one of only a small number of eruptions observed by a dual-polarisation radar worldwide. The eruption was also observed by a GeoNet webcam, and detailed ash deposit studies have permitted analysis of the plume characteristics. A combination of radar and webcam imagery show 5 pulses within the first 13 min of the eruption, and also the subsequent ash transport downwind. Comparison with ash samples show the radar was likely detecting ash particles down to about 0.5 mm diameter. The maximum plume height estimated by the radar is 7.8 ± 1.0 km above mean sea level (amsl), although it is possible this may be a slight under estimation if very small ash particles not detected by the radar rose higher and comprised the very top of the plume. The correlation coefficient and differential reflectivity fields that are additionally measured by the dual polarisation radar provide extra information about the structure and composition of the eruption column and ash cloud. The correlation coefficient easily discriminates between the eruption column and the ash plume, and provides some information about the diversity of ash particle size within both the ash plume and the subsequent detached ash cloud drifting downwind. The differential reflectivity shows that the larger ash particles are falling with a horizontal orientation, and indicates that ice nucleation and aggregation of fine ash particles was probably occurring at high altitudes within 20-25 min of the eruption.

Mantle heterogeneity in the source region of mid-ocean ridge basalts along the northern Central Indian Ridge (8°S-17°S)

NASA Astrophysics Data System (ADS)

Kim, Jonguk; Pak, Sang-Joon; Moon, Jai-Woon; Lee, Sang-Mook; Oh, Jihye; Stuart, Finlay M.

2017-04-01

The northern Central Indian Ridge (CIR) between 8°S and 17°S is composed of seven segments whose spreading rates increase southward from ˜35 to ˜40 mm/yr. During expeditions of R/V Onnuri to study hydrothermal activity on the northern CIR in 2009-2011, high-resolution multibeam mapping was conducted and ridge axis basalts were dredged. The major and trace element and Sr-Nd-Pb-He isotopic compositions of basaltic glasses dredged from the spreading axis require three mantle sources: depleted mantle and two distinct enriched mantle sources. The southern segments have Sr, Nd, and Pb that are a mix of depleted mantle and an enriched component as recorded in southern CIR MORB. This enrichment is indistinguishable from Rèunion plume mantle, except for He isotopes. This suggests that the southern segments have incorporated a contribution of the fossil Rèunion plume mantle, as the CIR migrated over hot-spot-modified mantle. The low 3He/4He (7.5-9.2 RA) of this enriched component may result from radiogenic 4He ingrowth in the fossil Rèunion mantle component. Basalts from the northern segments have high 206Pb/204Pb (18.53-19.15) and low 87Sr/86Sr (0.70286-0.70296) that are distinct from the Rèunion plume but consistent with derivation from mantle with FOZO signature, albeit with 3He/4He (9.2-11.8 RA) that are higher than typical. The FOZO-like enriched mantle cannot be attributed to the track of a nearby mantle plume. Instead, this enrichment may have resulted from recycling oceanic crust, possibly accompanied by small plume activity.

Anaerobic microbial redox processes in a landfill leachate contaminated aquifer (Grindsted, Denmark)

NASA Astrophysics Data System (ADS)

Ludvigsen, L.; Albrechtsen, H.-J.; Heron, G.; Bjerg, P. L.; Christensen, T. H.

1998-10-01

The distribution of anaerobic microbial redox processes was investigated along a 305 m long transect of a shallow landfill-leachate polluted aquifer. By unamended bioassays containing sediment and groundwater, 37 samples were investigated with respect to methane production, sulfate, iron, and manganese reduction, and denitrification. Methane production was restricted to the most reduced part of the plume with rates of 0.003-0.055 nmol CH 4/g dry weight/day. Sulfate reduction was observed at rates of maximum 1.8 nmol SO 42-/g dry weight/day along with methane production in the plume, but sulfate reduction was also observed further downgradient of the landfill. Iron reduction at rates of 5-19 nmol Fe(II)/g dry weight/day was observed in only a few samples, but this may be related to a high detection limit for the iron reducing bioassay. Manganese reduction at rates of maximum 2.4 nmol Mn(II)/g dry weight/day and denitrification at rates of 0.2-37 nmol N 2O-N/g dry weight/day were observed in the less reduced part of the plume. All the redox processes were microbial processes. In many cases, several redox processes took place simultaneously, but in all samples one process dominated accounting for more than 70% of the equivalent carbon conversion. The bioassays showed that the redox zones in the plume identified from the groundwater composition (e.g. as methanogenic and sulfate reducing) locally hosted also other redox processes (e.g. iron reduction). This may have implications for the potential of the redox zone to degrade trace amounts of organic chemicals and suggests that unamended bioassays may be an important supplement to other approaches in characterizing the redox processes in an anaerobic plume.