Influence of oxygen partial pressure on surface tension and its temperature coefficient of molten iron

NASA Astrophysics Data System (ADS)

Ozawa, S.; Suzuki, S.; Hibiya, T.; Fukuyama, H.

2011-01-01

Influences of oxygen partial pressure, PO2, of ambient atmosphere and temperature on surface tension and its temperature coefficient for molten iron were experimentally investigated by an oscillating droplet method using an electromagnetic levitation furnace. We successfully measured the surface tension of molten iron over a very wide temperature range of 780 K including undercooling condition in a well controlled PO2 atmosphere. When PO2 is fixed at 10-2 Pa at the inlet of the chamber, a "boomerang shape" temperature dependence of surface tension was experimentally observed; surface tension increased and then decreased with increasing temperature. The pure surface tension of molten iron was deduced from the negative temperature coefficient in the boomerang shape temperature dependence. When the surface tension was measured under the H2-containing gas atmosphere, surface tension did not show a linear relationship against temperature. The temperature dependence of the surface tension shows anomalous kink at around 1850 K due to competition between the temperature dependence of PO2 and that of the equilibrium constant of oxygen adsorption.

Removal of phosphate from eutrophic lakes through adsorption by in situ formation of magnesium hydroxide from diatomite.

PubMed

Xie, Fazhi; Wu, Fengchang; Liu, Guijian; Mu, Yunsong; Feng, Chenglian; Wang, Huanhua; Giesy, John P

2014-01-01

Since in situ formation of Mg(OH)2 can efficiently sorb phosphate (PO4) from low concentrations in the environment, a novel dispersed magnesium oxide nanoflake-modified diatomite adsorbent (MOD) was developed for use in restoration of eutrophic lakes by removal of excess PO4. Various adsorption conditions, such as pH, temperature and contact time were investigated. Overall, sorption capacities increased with increasing temperature and contact time, and decreased with increasing pH. Adsorption of PO4 was well described by both the Langmuir isotherm and pseudo second-order models. Theoretical maximum sorption capacity of MOD for PO4 was 44.44-52.08 mg/g at experimental conditions. Characterization of PO4 adsorbed to MOD by use of X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and solid state (31)P nuclear magnetic resonance revealed that electrostatic attraction, surface complexation and chemical conversion in situ were the major forces in adsorption of PO4. Mg(OH)2 formed in situ had a net positive charge on the surface of the MOD that could adsorb PO4(3-) and HPO4(2-) anion to form surface complex and gradually convert to Mg3(PO4)2 and MgHPO4. Efficiency of removal of PO4 was 90% when 300 mg MOD/L was added to eutrophic lake water. Results presented here demonstrated the potential use of the MOD for restoration of eutrophic lakes by removal of excess PO4.

Adsorption and Structure of Chiral Epoxides on Pd(111): Propylene Oxide and Glycidol

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mahapatra, Mausumi; Tysoe, Wilfred T.

Here, the adsorption of enantiopure versus racemic propylene oxide (PO) on Pd(111) is studied by temperature-programmed desorption (TPD) to explore possible differences in their saturation coverage. It is found that that the saturation coverage of enantiopure PO on Pd(111) is identical to that of racemic PO, in contrast to results on Pt(111) where significant coverage differences were found. The surface structures of enantiopure PO on Pd(111) were characterized by scanning tunneling microscopy (STM), which shows the formation of linear chains and hexagonal structures proposed to be due to freely rotating PO, in contrast to the relatively disordered PO overlayers foundmore » on Pt(111). STM experiments were carried out for enantiopure glycidol, which contains the same epoxy ring as PO, but where the methyl group of propylene oxide is replaced by a -CH 2OH group to provide a hydrogen-bonding sites. Glycidol STM images show the formation of completely different surface structures; at low coverages, glycidol forms pseudohexagonal structures which assemble from glycidol dimers, while at high coverages the surface shows extensive hydrogen-bonded networks. Density functional theory (DFT) calculations were carried out to model the enantiopure PO linear chain and the glycidol dimers that are observed by STM. Similar calculations were carried out for racemic PO and glycidol structures. The calculated interaction energies for the enantiopure and the racemic pairs reveal that there is no difference for homochiral versus heterochiral structures for both PO and glycidol on Pd(111).« less

Adsorption and Structure of Chiral Epoxides on Pd(111): Propylene Oxide and Glycidol

DOE PAGES

Mahapatra, Mausumi; Tysoe, Wilfred T.

2018-01-03

Here, the adsorption of enantiopure versus racemic propylene oxide (PO) on Pd(111) is studied by temperature-programmed desorption (TPD) to explore possible differences in their saturation coverage. It is found that that the saturation coverage of enantiopure PO on Pd(111) is identical to that of racemic PO, in contrast to results on Pt(111) where significant coverage differences were found. The surface structures of enantiopure PO on Pd(111) were characterized by scanning tunneling microscopy (STM), which shows the formation of linear chains and hexagonal structures proposed to be due to freely rotating PO, in contrast to the relatively disordered PO overlayers foundmore » on Pt(111). STM experiments were carried out for enantiopure glycidol, which contains the same epoxy ring as PO, but where the methyl group of propylene oxide is replaced by a -CH 2OH group to provide a hydrogen-bonding sites. Glycidol STM images show the formation of completely different surface structures; at low coverages, glycidol forms pseudohexagonal structures which assemble from glycidol dimers, while at high coverages the surface shows extensive hydrogen-bonded networks. Density functional theory (DFT) calculations were carried out to model the enantiopure PO linear chain and the glycidol dimers that are observed by STM. Similar calculations were carried out for racemic PO and glycidol structures. The calculated interaction energies for the enantiopure and the racemic pairs reveal that there is no difference for homochiral versus heterochiral structures for both PO and glycidol on Pd(111).« less

Methodological tools for the collection and analysis of participant observation data using grounded theory.

PubMed

Laitinen, Heleena; Kaunonen, Marja; Astedt-Kurki, Päivi

2014-11-01

To give clarity to the analysis of participant observation in nursing when implementing the grounded theory method. Participant observation (PO) is a method of collecting data that reveals the reality of daily life in a specific context. In grounded theory, interviews are the primary method of collecting data but PO gives a distinctive insight, revealing what people are really doing, instead of what they say they are doing. However, more focus is needed on the analysis of PO. An observational study carried out to gain awareness of nursing care and its electronic documentation in four acute care wards in hospitals in Finland. Discussion of using the grounded theory method and PO as a data collection tool. The following methodological tools are discussed: an observational protocol, jotting of notes, microanalysis, the use of questioning, constant comparison, and writing and illustrating. Each tool has specific significance in collecting and analysing data, working in constant interaction. Grounded theory and participant observation supplied rich data and revealed the complexity of the daily reality of acute care. In this study, the methodological tools provided a base for the study at the research sites and outside. The process as a whole was challenging. It was time-consuming and it required rigorous and simultaneous data collection and analysis, including reflective writing. Using these methodological tools helped the researcher stay focused from data collection and analysis to building theory. Using PO as a data collection method in qualitative nursing research provides insights. It is not commonly discussed in nursing research and therefore this study can provide insight, which cannot be seen or revealed by using other data collection methods. Therefore, this paper can produce a useful tool for those who intend to use PO and grounded theory in their nursing research.

Low collectivity of the first 2+ states of 212,210Po

NASA Astrophysics Data System (ADS)

Kocheva, D.; Rainovski, G.; Jolie, J.; Pietralla, N.; Blazhev, A.; Astier, A.; Altenkirch, R.; Bast, M.; Beckers, M.; Ansari, S.; Braunroth, Th.; Cappellazzo, M.; Cortés, M. L.; Dewald, A.; Diel, F.; Djongolov, M.; Fransen, C.; Gladnishki, K.; Goldkuhle, A.; Hennig, A.; Karayonchev, V.; Keatings, J. M.; Kluge, E.; Kröll, Th.; Litzinger, J.; Moschner, K.; Müller-Gatermann, C.; Petkov, P.; Rudigier, M.; Scheck, M.; Spagnoletti, P.; Scholz, Ph.; Schmidt, T.; Spieker, M.; Stahl, C.; Stegmann, R.; Stolz, A.; Vogt, A.; Stoyanova, M.; Thöle, P.; Warr, N.; Werner, V.; Witt, W.; Wölk, D.; Zamora, J. C.; Zell, K. O.; Van Isacker, P.; Ponomarev, V. Yu.

2018-05-01

The lifetimes of the first 2+ excited states of 212,210Po were measured in two transfer reactions 208Pb(12C,8Be)212Po and 208Pb(12C,10Be)210Po by the Recoil Distance Doppler Shift (RDDS) method and by the Doppler Shift Attenuation method (DSAM), respectively. The derived absolute B(E2) values of 2.6(3) W.u. for 212Po and 1.83(28) W.u. for 210Po indicate low collectivity. It is shown that the properties of the yrast {2}1+, {4}1+, {6}1+ and {8}1+ states in both nuclei cannot be described consistently in the framework of nuclear shell models. It is also demonstrated in the case of 210Po that Quasi-particle Phonon Model (QPM) calculations cannot overcome this problem thus indicating the existence of a peculiarity which is neglected in both theoretical approaches.

Data catalog for JPL Physical Oceanography Distributed Active Archive Center (PO.DAAC)

NASA Technical Reports Server (NTRS)

Digby, Susan

1995-01-01

The Physical Oceanography Distributed Active Archive Center (PO.DAAC) archive at the Jet Propulsion Laboratory contains satellite data sets and ancillary in-situ data for the ocean sciences and global-change research to facilitate multidisciplinary use of satellite ocean data. Geophysical parameters available from the archive include sea-surface height, surface-wind vector, surface-wind speed, surface-wind stress vector, sea-surface temperature, atmospheric liquid water, integrated water vapor, phytoplankton pigment concentration, heat flux, and in-situ data. PO.DAAC is an element of the Earth Observing System Data and Information System and is the United States distribution site for TOPEX/POSEIDON data and metadata.

A methodological approach to rapid assessment of a river flood in coastal waters. First test in the Po River delta

NASA Astrophysics Data System (ADS)

Campanelli, Alessandra; Bellafiore, Debora; Bensi, Manuel; Bignami, Francesco; Caccamo, Giuseppe; Celussi, Mauro; Del Negro, Paola; Ferrarin, Christian; Marini, Mauro; Paschini, Elio; Zaggia, Luca

2014-05-01

As part of the actions of the flagship project RITMARE (Ricerca ITaliana per il MARE) a daily oceanographic survey was performed on 29th November 2013 in front of the Po River delta (Northern Adriatic Sea). The Po river affects a large part of the Northern Adriatic Sea with strong implications on the circulation and functionality of the basin. Physical-chemical and biological properties of coastal waters were investigated after a moderate flood occurred around 25th-27th November. The cruise activities, carried out using a small research boat, were mainly focused on the test of a methodological approach to investigate the environment variability after a flood event in the framework of rapid assessment. The effects of the flood on the coastal waters, have been evaluated in the field using operational forecasts and real-time satellite imagery to assist field measurements and samplings. Surface satellite chlorophyll maps and surface salinity and current maps obtained from a numerical model forced by meteorological forecast and river data were analyzed to better identify the Po plume dispersion during and after the event in order to better locate offshore monitoring stations at the sea. Profiles of Temperature, Salinity, Turbidity, Fluorescence and Colored Dissolved Organic Matter (CDOM) throughout the water column were collected at 7 stations in front of the Po River delta. Sea surface water samples were also collected for the analysis of nutrients, Dissolved Organic Carbon (DOC) and CDOM (surface and bottom). The CDOM regulates the penetration of UV light throughout the water column and mediates photochemical reactions, playing an important role in many marine biogeochemical processes. Satellite images showed a strong color front that separates the higher-chlorophyll coastal water from the more oligotrophic mid-basin and eastern boundary Adriatic waters. In front of the river mouth, the surface layer was characterized by low salinity (14-15), high turbidity (8-11 NTU) and high CDOM (20-22 ppb) values. These parameters showed a strong gradient from coast to offshore and from surface to the bottom. The fluorescence values were more variable since the phytoplankton growth is not quickly correlated with the load of riverborne materials. The higher fluorescence values (1.8-2 µg l-1) were, in fact, detected offshore and at bottom. A good correlation between salinity versus CDOM (R2=0.84) and salinity versus Spectral slope (SCDOM275-295; R2=0.86) were found. These features reveal the role of CDOM as tracer of the freshwater inputs. Chemical analysis of waters affected by the river plume display high concentration of organic carbon (100-160 µmol l-1) and nutrients strenghtening this zone as one of the most eutrophic area of the Mediterranean Sea (Campanelli et al. 2011, Marini et al. 2008). The synergy of actions applied in the test has proved useful to better analyze the variability of coastal water characteristics after a river flood. However, a similar methodological approach could be reasonably applied to the rapid assessment of different events (i.e. harmful phytoplankton growth, chemical spills) which can occur in the area or in areas with similar features. The definition of methodologies for rapid assessment of marine processes can be a useful tool for the future integrated management of coastal zone. References Campanelli, A., F. Grilli, E. Paschini, M. Marini, 2011. The influence of an exceptional Po River flood on the physical and chemical oceanographic properties of the Adriatic Sea. Dynam. Atmos. Oceans, 52: 284-297. Marini, M., B.H. Jones, A. Campanelli, F. Grilli & C.M. Lee. 2008. Seasonal variability and Po River plume influence on biochemical properties along western Adriatic coast. J. Geophys. Res., 113: C05S90, doi:10.1029/2007JC004370.

Determining the charged fractions of 218Po and 214Pb using an environmental gamma-ray and Rn detector.

PubMed

Maiello, M L; Harley, N H

1989-07-01

The rate of 218Po and 214Pb atoms collected electrostatically inside an environmental gamma-ray and 222Rn detector (EGARD) was measured. These measurements were used to directly infer the charged fraction of 218Po and to calculate the charged fraction of 214Pb. Thirty-two percent of the 218Po was collected electrostatically using approximately -1500 V on a 2.54 cm diameter Mylar covered disc inside a vented A1 EGARD of 1 L volume. About 91% of the 214Pb is collected electrostatically under the same conditions. The measurements were performed in a calibrated 222Rn test chamber at the Environmental Measurements Laboratory (EML) using the Thomas alpha-counting method with 222Rn concentrations averaging about 4300 Bq m-3. The atomic collection rates were used with other measured quantities to calculate the thermoluminescent dosimeter (TLD) signal acquired from EGARD for exposure to 1 Bq m-3 of 222Rn. The calculations account for 222Rn progeny collection using a Teflon electret and alpha and beta detection using TLDs inside EGARD. The measured quantities include the energies of 218Po and 214Po alpha-particles degraded by passage through the 25 microns thick electret. The TLD responses to these alpha- and beta-particles with an average energy approaching that obtained from the combined spectra of 214Pb and 214Bi were also measured. The calculated calibration factor is within 30% of the value obtained by exposing EGARD to a known concentration of 222Rn. This result supports our charged fraction estimates for 218Po and 214Pb.

Humic acids contribution to sedimentary organic matter on a shallow continental shelf (northern Adriatic Sea)

NASA Astrophysics Data System (ADS)

Giani, M.; Rampazzo, F.; Berto, D.

2010-12-01

The shallow northern Adriatic Sea receives large river runoff, predominantly from the Po River, which is the main allochthonous source of nutrients and organic matter. The origin and quality of organic matter deposited in the sediments can influence the degradation processes and oxygen consumption in the bottom waters as well as the fate of many pollutants. Therefore the humic acids (HA) were quantified in surface and sub-surface sediments collected in an area of the north-western Adriatic platform south of Po River. HA showed to have a relevant contribution to sedimentary organic matter. HA content in sediments were positively correlated with the organic carbon concentration and negatively with redox potential and pH, particularly in sub-surface reduced sediments, suggesting their important role in the diagenetic processes taking place in anoxic conditions. Elemental composition of HA extracted from surface and sub-surface sediments showed a wide range of variation of the C org/N ratios which could be due to a mixed (terrestrial and marine) origin and/or an elevated bacteria degradation of nitrogen during diagenesis processes in sediments. The spectroscopic ratios A 2/A 4 and A 4/A 6 of HA confirmed a mixed origin with a high degree of condensation of the HA extracted from sediments.

JPL Physical Oceanography Distributed Active Archive Center (PO.DAAC) data availability, version 1-94

NASA Technical Reports Server (NTRS)

1994-01-01

The Physical Oceanography Distributed Active Archive Center (PO.DAAC) archive at the Jet Propulsion Laboratory (JPL) includes satellite data sets for the ocean sciences and global-change research to facilitate multidisciplinary use of satellite ocean data. Parameters include sea-surface height, surface-wind vector, sea-surface temperature, atmospheric liquid water, and integrated water vapor. The JPL PO.DAAC is an element of the Earth Observing System Data and Information System (EOSDIS) and is the United States distribution site for Ocean Topography Experiment (TOPEX)/POSEIDON data and metadata.

Detection of 210Po on filter papers 16 years after use for the collection of short-lived radon progeny in a room.

PubMed

Abu-Jarad, F; Fazal-ur-Rehman

2003-01-01

Radon gas was allowed to accumulate in its radium source and then injected into a 36 m(3) test room, resulting in an initial radon concentration of 15 kBq m(-3). Filter papers were used to collect the short-lived radon progeny and thus to measure the Potential Alpha Energy Concentration (PAEC) in-situ in the year 1984 at different times and conditions according to the experimental design. The radon progeny collected on the filter papers were studied as a function of aerosol particle concentration ranging from 10(2)-10(5) particles cm(-3) in three different experiments. The highest aerosol particle concentration was generated by indoor cigarette smoking. Those filters were stored after the experiment, and were used after 16 years to study the activity of the radon long-lived alpha emitter progeny, (210)Po (T(1/2)=138 days). This isotope is separated from the short-lived progeny by (210)Pb beta emitter with 22.3 years half-life. After 16 years' storage of these filters, each filter paper was sandwiched and wrapped between two CR-39 nuclear track detectors, to put the detectors in contact with the surfaces of different filters, for 337 days. Correlation between the PAEC measured using filter papers in the year 1984 and the activity of long-lived alpha emitter (210)Po on the same filter papers measured in the year 2000 were studied. The results of the (210)Po activity showed a very good correlation of 0.92 with the PAEC 16 years ago. The results also depict that the PAEC and (210)Po activity in indoor air increased with the increase of aerosol particle concentration, which shows the attachment of short-lived radon progeny with the aerosol particles. The experiment proves that indoor cigarette smoking is a major source of aerosol particles carrying radon progeny and, thus, indoor cigarette smoking is an additional source of internal radiation hazard to the occupants whether smoker or non-smoker.

Unusually high (210)Po activities in the surface water of the Zhubi Coral Reef Lagoon in the South China Sea.

PubMed

Yang, Weifeng; Huang, Yipu; Chen, Min; Qiu, Yusheng; Li, Hongbin; Zhang, Lei

2011-10-01

Recent researches revealed the exciting application of (210)Po in tracing carbon and nitrogen cycling in the coral reef system. In order to quantify the recycling of particulate organic nitrogen (PON), both (210)Po and (210)Pb were examined at both high and low tides in the Zhubi Coral Reef lagoon, the South China Sea. Unusually, much higher (210)Po activities and (210)Po/(210)Pb ratios, in comparison with those found in the open seawater and the lagoon subsurface water, showed additional input of (210)Po besides production from in situ(210)Pb in the lagoon surface water. Statistical analysis identified that the reef flat seawater was the additional (210)Po source. Based on a mass balance model, the input rates of (210)Po varied from 0.04 Bq m(-3)year(-1) to 8.41 Bq m(-3)year(-1). On average, the additional (210)Po contributed more than 60% of the total (210)Po. The particulate (210)Po significantly correlated with the concentrations of PON, indicating that diffusion of (210)Po from sediment could be used to quantify the recycling of nitrogen. The average input rate of nitrogen was 16 mmol m(-3)year(-1), which can support up to 11% of the primary production rate. These results suggested that the unusual behavior of (210)Po could provide new insight into the nitrogen recycling in the coral reef system. Copyright © 2011 Elsevier B.V. All rights reserved.

Radon daughter disequilibria and lead systematics in the western North Atlantic

NASA Astrophysics Data System (ADS)

Hussain, N.; Church, T. M.; VéRon, Alain J.; Larson, R. E.

1998-01-01

Concentrations of 222Rn and 210Pb were measured in the North Atlantic troposphere in 1989 between April 12 and 28, during the Sulfide Experiment (SEX) Cruise I, and those of 222Rn, 210Pb and 210Po, between October 24 and November 9, during the SEX Cruise II. Concentrations of 210Pb and 210Po were also measured in the rain water, surface seawater, and marine microlayer collected during the SEX Cruise II Other data used and published previously include stable lead and its isotopes [Vèron et al., 1992, 1993] on parallel samples. Low 222Rn contents, of the order of 0.1 and 0.3 Bq m-3, were found in the marine air, while continental air showed nearly 10 times higher concentrations of 222Rn. These results corroborate with the air mass trajectory analyses and continental signatures of stable lead isotopes. Significant correlation is found between 222Rn and 210Pb on the aerosol, indicative of excess continental 222Rn supporting the ingrowth of 210Pb from the atmosphere, in spite of its first-order removal by precipitation. Correlation between 210Pb and stable Pb on the aerosol and in the precipitation document the source of pollutant lead from the continental surface. Mean residence times of marine aerosol based on 210Pb is estimated to be 5.4±1.8 days during the April cruise and 19.7±1.9 days during the October cause. Corresponding deposition velocity for 210Pb is estimated to be 1.9±1.9 cm s-1, a value that suggests the dominant role of precipitation scavenging, or aerosol scavenging by larger host phases such as dust or sea salt. Excess 210Po activities are found on the aerosol relative to what would be expected based on 210Pb and the aerosol residence times. In surface seawaters, deficiencies of 210Po are observed. Mechanisms of 210Po enrichment in atmospheric aerosol may include enrichments from the organic components of marine microlayer, sea-salt aerosol, dust, or air-sea exchange of volatile organo-polonium species.

Li3PO4 surface coating on Ni-rich LiNi0.6Co0.2Mn0.2O2 by a citric acid assisted sol-gel method: Improved thermal stability and high-voltage performance

NASA Astrophysics Data System (ADS)

Lee, Suk-Woo; Kim, Myeong-Seong; Jeong, Jun Hui; Kim, Dong-Hyun; Chung, Kyung Yoon; Roh, Kwang Chul; Kim, Kwang-Bum

2017-08-01

A surface coating of Li3PO4 was applied to a Ni-rich LiNi0.6Co0.2Mn0.2O2 (NCM) material to improve its thermal stability and electrochemical properties via a citric acid assisted sol-gel method. The addition of citric acid effectively suppressed the instant formation of Li3PO4 in solution, resulting in successful coating of the NCM surface. The improved thermal stability of NCM after Li3PO4 surface coating was demonstrated by differential scanning calorimetry (DSC) analysis and in situ time-resolved X-ray diffraction (TR-XRD). In particular, the TR-XRD results showed that the improved thermal stability after Li3PO4 surface coating originates from suppression of the phase transition of charged NCM at high temperatures. Furthermore, the charge-discharge tests demonstrated that Li3PO4-coated LiNi0.6Co0.2Mn0.2O2 (LP-NCM) has excellent electrochemical properties. LP-NCM exhibited a specific capacity of 192.7 mAh g-1, a capacity retention of 44.1% at 10 C, and a capacity retention of 79.7% after 100 cycles at a high cut-off voltage of 4.7 V; these values represent remarkably improved electrochemical properties compared with those of bare NCM. These improved thermal and electrochemical properties were mainly attributed to the improvement of the structural stability of the material and the suppression of the interface reaction between the cathode and the electrolyte owing to the Li3PO4 coating.

Chemically grafted carbon-coated LiFePO4 using diazonium chemistry

NASA Astrophysics Data System (ADS)

Delaporte, Nicolas; Perea, Alexis; Amin, Ruhul; Zaghib, Karim; Bélanger, Daniel

2015-04-01

The effect of surface functionalization of aminophenyl and bromophenyl groups on carbon-coated LiFePO4 and the electrochemical properties of composite electrode containing these materials are reported. The functionalization was performed by spontaneous reduction of the corresponding in situ generated diazonium ions. The resulting chemically grafted LiFePO4/C materials were characterized by energy-dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) to confirm the presence of the surface organic species. XRD analyses indicated the cathode material was partially oxidized. Thermogravimetric and elemental analyses revealed the loading of grafted molecules was between 0.2 and 1.1 wt.% depending on the reaction conditions. Interestingly, the electrochemical performances of the modified LiFePO4/C are not adversely affected by the presence of either aminophenyl and bromophenyl groups at the carbon surface, and in fact the grafted LiFePO4/C displayed slightly superior discharge capacity at the highest C rate investigated for a low loading of organic molecules.

Surface properties and electromagnetic excitation of a piezoelectric gallium phosphate biosensor.

PubMed

Vasilescu, Alina; Ballantyne, Scott M; Cheran, Larisa-Emilia; Thompson, Michael

2005-02-01

The surface properties of GaPO4 have been studied by secondary ion mass spectrometry, X-ray photoelectron spectroscopy and electromagnetic acoustic wave excitation in order to explore the potential of this relatively new piezoelectric material as a biosensor. The X-ray photoelectron spectrum of the substrate shows a Ga-rich surface (Ga:P = 1.4), while the negative secondary ion mass spectrum is similar to that of other phosphates, with PO3- and PO2- being the main fragments derived from the substrate. Surface analysis reveals that the linker protein for biotinylated moieties, neutravidin, is both readily chemisorbed to bare gallium phosphate at pH 7.5 and attached to p-hydroxy benzaldehyde-treated devices, establishing the possibility to exploit the surface chemistry of the phosphate for the fabrication of an electrode-free acoustic wave biosensor. Preliminary results regarding the detection of the adsorption of neutravidin with an electromagnetic field-excited GaPO4 device incorporated in a FIA configuration showed comparable results with those obtained with a quartz-sensor equivalent. The frequency shift for the adsorbed protein layer at the device fundamental frequency was 200 Hz and the noise was routinely around 13 Hz. The possibility to use the electrodeless acoustic GaPO4 device at higher harmonics in the liquid phase has also been confirmed.

Targeted partial surface modification with nano-SiO2@Li2CoPO4F as high-voltage cathode material for LIBs

NASA Astrophysics Data System (ADS)

Chang, Caiyun; Huang, Zhipeng; Tian, Runsai; Jiang, Xinyu; Li, Chunsheng; Feng, Jijun

2017-10-01

Tuning whole/partial surface modification on cathode material with oxide material is a sought-after method to enhance the electrochemical performance in power storage field. Herein, nano-SiO2 targeted partial surface modified high voltage cathode material Li2CoPO4F has been successfully fabricated via a facile self-assembly process in silica dispersion at ambient temperature. With the aid of polar -OH groups attracted on the surface of SiO2 micelles, the nano-SiO2 preferentially nestle up along the borders and boundaries of Li2CoPO4F particles, where protection should be deployed with emphasis against the undesirable interactions between materials and electrolytes. Compared with pristine Li2CoPO4F, the SiO2 selectively modified Li2CoPO4F cathode materials, especially LCPF-3S, exhibit desirable electrochemical performances with higher discharge capacity, more outstanding cycle stability and favorable rate capability without any additional carbon involved. The greatly enhanced electrochemical properties can be attributed to the improved lithium-ion diffusion kinetics and structure tolerance during repeated lithiation/delithiation process. Such findings reveal a great potential of nano-SiO2 modified Li2CoPO4F as high energy cathode material for lithium ion batteries.

Radionuclides (210Po and 210Pb) and Some Heavy Metals in Fish and Sediments in Lake Bafa, Turkey, and the Contribution of 210Po to the Radiation Dose.

PubMed

Manav, Ramazan; Uğur Görgün, Aysun; Filizok, Işık

2016-11-09

The pollution level of Lake Bafa was investigated by collecting fish samples { Dicentrarchus labrax (sea bass), Liza ramada (mullet) and Anguilla anguilla (eel)}, surface sediment, and core samples. In all these samples, 210 Po and 210 Pb concentrations were estimated, and total annual dose rates were obtained for each species. Some heavy metal (Cr, Ni, Pb, Cd, Mn, Fe, and Zn) concentration levels were obtained for the fish and a core sample. The sediment mass accumulation rate was found to be 3.27 g·m -2 ·day -1 (0.119 g·cm -2 ·y -1 ) from a core sample. The heavy metal concentrations in the vertical profile of samples from the core were also observed. The measured concentration of Zn, Pb, Cd, and Cr were between the ERL (effects range low) and ERM (effects range median) limits, while Ni concentrations were higher than the ERM limit. The observed concentrations of Cd, Pb, and Zn in fish samples did not exceed the limits in accordance with Turkish Food Regulations. Further, the maximum effective dose equivalent of 210 Po in the area was found to be 1.169 µSv·y -1 .

Nutrient load generated by storm event runoff from a golf course watershed.

PubMed

King, K W; Balogh, J C; Hughes, K L; Harmel, R D

2007-01-01

Turf, including home lawns, roadsides, golf courses, parks, etc., is often the most intensively managed land use in the urban landscape. Substantial inputs of fertilizers and water to maintain turf systems have led to a perception that turf systems are a major contributor to nonpoint source water pollution. The primary objective of this study was to quantify nutrient (NO(3)-N, NH(4)-N, and PO(4)-P) transport in storm-generated surface runoff from a golf course. Storm event samples were collected for 5 yr (1 Apr. 1998-31 Mar. 2003) from the Morris Williams Municipal Golf Course in Austin, TX. Inflow and outflow samples were collected from a stream that transected the golf course. One hundred fifteen runoff-producing precipitation events were measured. Median NO(3)-N and PO(4)-P concentrations at the outflow location were significantly (p < 0.05) greater than like concentrations measured at the inflow location; however, median outflow NH(4)-N concentration was significantly less than the median inflow concentration. Storm water runoff transported 1.2 kg NO(3)-N ha(-1) yr(-1), 0.23 kg NH(4)-N ha(-1) yr(-1), and 0.51 kg PO(4)-P ha(-1) yr(-1) from the course. These amounts represent approximately 3.3% of applied N and 6.2% of applied P over the contributing area for the same period. NO(3)-N transport in storm water runoff from this course does not pose a substantial environmental risk; however, the median PO(4)-P concentration exiting the course exceeded the USEPA recommendation of 0.1 mg L(-1) for streams not discharging into lakes. The PO(4)-P load measured in this study was comparable to soluble P rates measured from agricultural lands. The findings of this study emphasize the need to balance golf course fertility management with environmental risks, especially with respect to phosphorus.

Putting User Stories First: Experiences Adapting the Legacy Data Models and Information Architecture at NASA JPL's PO.DAAC to Accommodate the New Information Lifecycle Required by SWOT

NASA Astrophysics Data System (ADS)

McGibbney, L. J.; Hausman, J.; Laurencelle, J. C.; Toaz, R., Jr.; McAuley, J.; Freeborn, D. J.; Stoner, C.

2016-12-01

The Surface Water & Ocean Topography (SWOT) mission brings together two communities focused on a better understanding of the world's oceans and its terrestrial surface waters. U.S. and French oceanographers and hydrologists and international partners have joined forces to develop this new space mission. At NASA JPL's PO.DAAC, the team is currently engaged in the gathering of SWOT User Stores (access patterns, metadata requirements, primary and value added product requirements, data access protocols, etc.) to better inform the adaptive planning of what will be known as the next generation PO.DAAC Information Architecture (IA). The IA effort acknowledges that missions such as SWOT (and NISAR) have few or no precedent in terms of data volume, hot and cold storage, archival, analysis, existing system engineering complexities, etc. and that the only way we can better understand the projected impacts of such requirements is to interface directly with the User Community. Additionally, it also acknowledges that collective learning has taken place to understand certain limitations in the existing data models (DM) underlying the existing PO.DAAC Data Management and Archival System. This work documents an evolutionary, use case based, standards driven approach to adapting the legacy DM and accompanying knowledge representation infrastructure at NASA JPL's PO.DAAC to address forthcoming DAAC mission requirements presented by missions such as SWOT. Some of the topics covered in this evolution include, but are not limited to: How we are leveraging lessons learned from the development of existing DM (such as that generated for SMAP) in an attempt to map them to SWOT. What is the governance model for the SWOT IA? What are the `governing' entities? What is the hierarchy of the `governed entities'? How are elements grouped? How is the design-working group formed? How is model independence maintained and what choices/requirements do we have for the implementation language? The use of Standards such as CF Conventions, NetCDF, HDF and ISO Metadata, etc. Beyond SWOT… what choices were made such that the new PO.DAAC IA will flexible enough and adequately design such that future missions with even more advanced requirements can be accommodated within PO.DAAC.

Temperature dependence of surface tension of molten iron under reducing gas atmosphere

NASA Astrophysics Data System (ADS)

Ozawa, S.; Takahashi, S.; Fukuyama, H.; Watanabe, M.

2011-12-01

Surface tension of molten iron was measured under Ar-He-5vol.%H2 gas by oscillating droplet method using electromagnetic levitation furnace in consideration of the temperature dependence of oxygen partial pressure, Po2, of the gas. For comparison, the measurement was carried under Ar-He atmosphere to fix the Po2 of the inlet gas at 10-2Pa. The surface tension was successfully measured over a wide temperature range of about 780K including undercooling condition. When Po2 is fixed at 10-2 Pa, the surface tension increased and then decreased with increasing temperature like a boomerang shape. When the measurement was carried out under the H2-containing gas atmosphere, the temperature dependence of the surface tension shows unique kink at around 1810K instead of liner relationship due to competition between the temperature dependence of the Po2 and that of the equilibrium constant of oxygen adsorption reaction. The relationship between the calculated lnKad with respect to inverse temperature using Szyszkowski model was different between the atmospheric gases.

Improved GO/PO method and its application to wideband SAR image of conducting objects over rough surface

NASA Astrophysics Data System (ADS)

Jiang, Wang-Qiang; Zhang, Min; Nie, Ding; Jiao, Yong-Chang

2018-04-01

To simulate the multiple scattering effect of target in synthetic aperture radar (SAR) image, the hybrid method GO/PO method, which combines the geometrical optics (GO) and physical optics (PO), is employed to simulate the scattering field of target. For ray tracing is time-consuming, the Open Graphics Library (OpenGL) is usually employed to accelerate the process of ray tracing. Furthermore, the GO/PO method is improved for the simulation in low pixel situation. For the improved GO/PO method, the pixels are arranged corresponding to the rectangular wave beams one by one, and the GO/PO result is the sum of the contribution values of all the rectangular wave beams. To get high-resolution SAR image, the wideband echo signal is simulated which includes information of many electromagnetic (EM) waves with different frequencies. Finally, the improved GO/PO method is used to simulate the SAR image of targets above rough surface. And the effects of reflected rays and the size of pixel matrix on the SAR image are also discussed.

Carbon coatings with olive oil, soybean oil and butter on nano-LiFePO 4

NASA Astrophysics Data System (ADS)

Kim, Ketack; Jeong, Ji Hwa; Kim, Ick-Jun; Kim, Hyun-Soo

Kitchen oils (olive, soybean and butter) are selected for carbon coatings on LiFePO 4. The surface properties of LiFePO 4 are unknown or vary depending on synthetic methods. The multi-functional groups of fatty acids in the oils can orient properly to cope with the variable surface properties of LiFePO 4, which can lead to dense carbon coatings. The low price and low toxicity of kitchen oils are other advantages of the coating process. LiFePO 4 (D 50 = 121 nm)combined with the carbon coating enhances the rate capability. Capacities at the 2 C rate reach 150 mAh g -1 or higher. The charge retention values of 2.0 C/0.2 C are between 94.4 and 98.9%.

Accelerated Removal of Fe-Antisite Defects while Nanosizing Hydrothermal LiFePO4 with Ca(2).

PubMed

Paolella, Andrea; Turner, Stuart; Bertoni, Giovanni; Hovington, Pierre; Flacau, Roxana; Boyer, Chad; Feng, Zimin; Colombo, Massimo; Marras, Sergio; Prato, Mirko; Manna, Liberato; Guerfi, Abdelbast; Demopoulos, George P; Armand, Michel; Zaghib, Karim

2016-04-13

Based on neutron powder diffraction (NPD) and high angle annular dark field scanning transmission electron microscopy (HAADF-STEM), we show that calcium ions help eliminate the Fe-antisite defects by controlling the nucleation and evolution of the LiFePO4 particles during their hydrothermal synthesis. This Ca-regulated formation of LiFePO4 particles has an overwhelming impact on the removal of their iron antisite defects during the subsequent carbon-coating step since (i) almost all the Fe-antisite defects aggregate at the surface of the LiFePO4 crystal when the crystals are small enough and (ii) the concomitant increase of the surface area, which further exposes the Fe-antisite defects. Our results not only justify a low-cost, efficient and reliable hydrothermal synthesis method for LiFePO4 but also provide a promising alternative viewpoint on the mechanism controlling the nanosizing of LiFePO4, which leads to improved electrochemical performances.

Corneal Equilibrium Flux as a Function of Corneal Surface Oxygen Tension.

PubMed

Compañ, Vicente; Aguilella-Arzo, Marcel; Weissman, Barry A

2017-06-01

Oxygen is essential for aerobic mammalian cell physiology. Oxygen tension (PO2) should reach a minimum at some position within the corneal stroma, and oxygen flux should be zero, by definition, at this point as well. We found the locations and magnitudes of this "corneal equilibrium flux" (xmin) and explored its physiological implications. We used an application of the Monod kinetic model to calculate xmin for normal human cornea as anterior surface PO2 changes from 155 to 20 mmHg. We find that xmin deepens, broadens, and advances from 1.25 μm above the endothelial-aqueous humor surface toward the epithelium (reaching a position 320 μm above the endothelial-aqueous humor surface) as anterior corneal surface PO2 decreases from 155 to 20 mmHg. Our model supports an anterior corneal oxygen flux of 9 μL O2 · cm · h and an epithelial oxygen consumption of approximately 4 μL O2 · cm · h. Only at the highest anterior corneal PO2 does our model predict that oxygen diffuses all the way through the cornea to perhaps reach the anterior chamber. Of most interest, corneal oxygen consumption should be supported down to a corneal surface PO2 of 60 to 80 mmHg but declines below this range. We conclude that the critical oxygen tension for hypoxia induced corneal swelling is more likely this range rather than a fixed value.

Role of graphene on the surface chemical reactions of BiPO4-rGO with low OH-related defects.

PubMed

Gao, Erping; Wang, Wenzhong

2013-11-21

Graphene has been widely introduced into photocatalysis to enhance photocatalytic performance due to its unique physical and chemical properties. However, the effect of graphene on the surface chemical reactions of photocatalysis has not been clearly researched, which is important for photocatalysis because photocatalytic reactions ultimately occur on the catalyst surface. Herein, a two-step solution-phase reaction has been designed to synthesize quasi-core-shell structured BiPO4-rGO cuboids and the role of graphene on the surface chemical reactions was investigated in detail. It was found that the introduced graphene modified the process and the mechanism of the surface chemical reactions. The change mainly originates from the interaction between graphene and the adsorbed O2 molecule. Due to the electron transfer from graphene to adsorbed O2, graphene could tune the interfacial charge transport and efficiently activate molecular oxygen to form O2˙(-) anions as the major oxidation species instead of ˙OH. In addition, the two-step synthesis approach could efficiently suppress the formation of OH-related defects in the lattice. As a result, the BiPO4-rGO composite exhibited superior photocatalytic activity to BiPO4 and P25, about 4.3 times that of BiPO4 and 6.9 times that of P25.

Transition metal redox and Mn disproportional reaction in LiMn0.5Fe0.5PO4 electrodes cycled with aqueous electrolyte

NASA Astrophysics Data System (ADS)

Zhuo, Zengqing; Hu, Jiangtao; Duan, Yandong; Yang, Wanli; Pan, Feng

2016-07-01

We performed soft x-ray absorption spectroscopy (sXAS) and a quantitative analysis of the transition metal redox in the LiMn0.5Fe0.5PO4 electrodes upon electrochemical cycling. In order to circumvent the complication of the surface reactions with organic electrolyte at high potential, the LiMn0.5Fe0.5PO4 electrodes are cycled with aqueous electrolyte. The analysis of the transitional metal L-edge spectra allows a quantitative determination of the redox evolution of Mn and Fe during the electrochemical cycling. The sXAS analysis reveals the evolving Mn oxidation states in LiMn0.5Fe0.5PO4. We found that electrochemically inactive Mn2+ is formed on the electrode surface during cycling. Additionally, the signal indicates about 20% concentration of Mn4+ at the charged state, providing a strong experimental evidence of the disproportional reaction of Mn3+ to Mn2+ and Mn4+ on the surface of the charged LiMn0.5Fe0.5PO4 electrodes.

High-capacity cathodes for lithium-ion batteries from nanostructured LiFePO4 synthesized by highly-flexible and scalable flame spray pyrolysis

NASA Astrophysics Data System (ADS)

Hamid, N. A.; Wennig, S.; Hardt, S.; Heinzel, A.; Schulz, C.; Wiggers, H.

2012-10-01

Olivine, LiFePO4 is a promising cathode material for lithium-ion batteries due to its low cost, environmental acceptability and high stability. Its low electric conductivity prevented it for a long time from being used in large-scale applications. Decreasing its particle size along with carbon coating significantly improves electronic conductivity and lithium diffusion. With respect to the controlled formation of very small particles with large specific surface, gas-phase synthesis opens an economic and flexible route towards high-quality battery materials. Amorphous FePO4 was synthesized as precursor material for LiFePO4 by flame spray pyrolysis of a solution of iron acetylacetonate and tributyl phosphate in toluene. The pristine FePO4 with a specific surface from 126-218 m2 g-1 was post-processed to LiFePO4/C composite material via a solid-state reaction using Li2CO3 and glucose. The final olivine LiFePO4/C particles still showed a large specific surface of 24 m2 g-1 and were characterized using X-ray diffraction (XRD), electron microscopy, X-ray photoelectron spectrocopy (XPS) and elemental analysis. Electrochemical investigations of the final LiFePO4/C composites show reversible capacities of more than 145 mAh g-1 (about 115 mAh g-1 with respect to the total coating mass). The material supports high drain rates at 16 C while delivering 40 mAh g-1 and causes excellent cycle stability.

H3PO4 treated surface modified CuS counter electrodes with high electrocatalytic activity for enhancing photovoltaic performance of quantum dot-sensitized solar cells

NASA Astrophysics Data System (ADS)

Panthakkal Abdul Muthalif, Mohammed; Sunesh, Chozhidakath Damodharan; Choe, Youngson

2018-05-01

Herein we report a simple synthetic strategy to prepare highly efficient and surface modified CuS counter electrodes (CEs) for quantum dot-sensitized solar cells (QDSSCs) in the presence of phosphoric acid (H3PO4) using the chemical bath deposition method. This is the first report of successful treatment of H3PO4 on the surface of CuS CEs for designing a high-performance QDSSCs with improved photovoltaic properties. After optimization, the 4 ml H3PO4 treated CuS CE-based QDSSC exhibits excellent photovoltaic performance with a conversion efficiency (η) of 4.20% (Voc = 0.592 V, Jsc = 13.35 mA cm-2, FF = 0.532) under one full-sun illumination (100 mW cm-2, AM 1.5 G).

Impact of point-of-care ultrasound on clinical decision-making at an urban emergency department in Tanzania.

PubMed

Reynolds, Teri Ann; Amato, Stas; Kulola, Irene; Chen, Chuan-Jay Jeffrey; Mfinanga, Juma; Sawe, Hendry Robert

2018-01-01

Point of care ultrasound (PoCUS) is an efficient, inexpensive, safe, and portable imaging modality that can be particularly useful in resource-limited settings. However, its impact on clinical decision making in such settings has not been well studied. The objective of this study is to describe the utilization and impact of PoCUS on clinical decision making at an urban emergency department in Dar es Salaam, Tanzania. This was a prospective descriptive cross-sectional study of patients receiving PoCUS at Muhimbili National Hospital's Emergency Medical Department (MNH EMD). Data on PoCUS studies during a period of 10 months at MNH EMD was collected on consecutive patients during periods when research assistants were available. Data collected included patient age and sex, indications for ultrasound, findings, interpretations, and provider-reported diagnostic impression and disposition plan before and after PoCUS. Descriptive statistics, including medians and interquartile ranges, and counts and percentages, are reported. Pearson chi squared tests and p-values were used to evaluate categorical data for significant differences. PoCUS data was collected for 986 studies performed on 784 patients. Median patient age was 32 years; 56% of patients were male. Top indications for PoCUS included trauma, respiratory presentations, and abdomino-pelvic pain. The most frequent study types performed were eFAST, cardiac, and obstetric or gynaecologic studies. Overall, clinicians reported that the use of PoCUS changed either diagnostic impression or disposition plan in 29% of all cases. Rates of change in diagnostic impression or disposition plan increased to 45% in patients for whom more than one PoCUS study type was performed. In resource-limited emergency care settings, PoCUS can be utilized for a wide range of indications and has substantial impact on clinical decision making, especially when more than one study type is performed.

Particle Size, Surface Area, and Amorphous Content as Predictors of Solubility and Bioavailability for Five Commercial Sources of Ferric Orthophosphate in Ready-To-Eat Cereal

PubMed Central

Dickmann, Robin S.; Strasburg, Gale M.; Romsos, Dale R.; Wilson, Lori A.; Lai, Grace H.; Huang, Hsimin

2016-01-01

Ferric orthophosphate (FePO4) has had limited use as an iron fortificant in ready-to-eat (RTE) cereal because of its variable bioavailability, the mechanism of which is poorly understood. Even though FePO4 has desirable sensory properties as compared to other affordable iron fortificants, few published studies have well-characterized its physicochemical properties. Semi-crystalline materials such as FePO4 have varying degrees of molecular disorder, referred to as amorphous content, which is hypothesized to be an important factor in bioavailability. The objective of this study was to systematically measure the physicochemical factors of particle size, surface area, amorphous content, and solubility underlying the variation in FePO4 bioavailability. Five commercial FePO4 sources and ferrous sulfate were added to individual batches of RTE cereal. The relative bioavailability value (RBV) of each iron source, determined using the AOAC Rat Hemoglobin Repletion Bioassay, ranged from 51% to 99% (p < 0.05), which is higher than typically reported. Solubility in dilute HCl accurately predicted RBV (R2 = 0.93, p = 0.008). Amorphous content measured by Dynamic Vapor Sorption ranged from 1.7% to 23.8% and was a better determinant of solubility (R2 = 0.91; p = 0.0002) than surface area (R2 = 0.83; p = 0.002) and median particle size (R2 = 0.59; p = 0.12). The results indicate that while solubility of FePO4 is highly predictive of RBV, solubility, in turn, is strongly linked to amorphous content and surface area. This information may prove useful for the production of FePO4 with the desired RBV. PMID:26938556

Distribution of Ra isotopes and the 210Pb and 210Po balance in surface seawaters of the mid Northern Hemisphere

NASA Astrophysics Data System (ADS)

Nozaki, Yoshiyuki; Dobashi, Fumi; Kato, Yoshihisa; Yamamoto, Yoshiyuki

1998-08-01

210Po, 210Pb, 228Ra, and 226Ra were measured in surface sea waters along the 1989-1990 global traverse of the oceans using the new R.V. Hakuho-Maru. Where the traverse intersects other expedition routes, the data are generally confirmatory. In the high-productivity regimes like the Red Sea, and the Arabian Sea 210Po is removed from the mixed layer at much faster rates than 210Pb. This fractionation occurs during scavenging presumably because 210Po is strongly sorbed by organic particles, whereas 210Pb is more likely associated with inorganic detritus. The 210Po/ 210Pb activity ratios leaving the mixed layer by particulate transport can be estimated from the steady state balance of 210Pb and 210Po in the surface waters for different oceanic regions, and are compared with those in the literature obtained by sediment-trap experiments. Although this comparison appears to merge, there exist some inconsistencies, which may be attributable to one of the following possibilities: (1) the model-derived atmospheric 210Pb flux is overestimated for the North Pacific and the North Atlantic, or (2) the sediment-trap data do not represent the real 210Po/ 210Pb ratio in the vertical particulate flux due to some experimental artifacts, such as incomplete trapping and size fractionation. Further careful studies of sediment trapping including seasonal variation are needed to resolve this issue. Our Ra data confirmed that strong sources for 228Ra exist in the Bay of Bengal and the Southeast Asian continental shelf zone, whereas the Mediterranean and the Red Sea, though they are surrounded by land, are not effective sources of 228Ra in the surface water.

Estimation of 210Po and its risk to human beings due to consumption of marine species at Mumbai, India.

PubMed

Mishra, S; Bhalke, S; Pandit, G G; Puranik, V D

2009-07-01

(210)Po was estimated in the edible muscle and soft tissue of 15 different marine species (fish, crab, prawn and bivalve) collected from Trans-Thane Creek area (Trombay) and Thane. Potential risks associated with consumption of marine organisms due to (210)Po collected from this particular area to human beings were assessed. Estimation of (210)Po was carried out using radiochemical separation and alpha spectrometric technique. The concentration of (210)Po was found to vary from 0.18 to 10.9 Bqkg(-1) wet wt in different biota species and maximum concentrations were observed in bivalves. The variations in (210)Po concentration in different species are mainly due to difference in metabolism and feeding habits. The daily intake and individual dose of (210)Po to human beings through biota consumption was calculated and found to be 31.89 mBqd(-1) and 19.44 microSvyr(-1), respectively. An assessment of the risk on human beings due to consumption of marine organism was undertaken using carcinogenic slope factor for (210)Po. 5th, 50th and 95th percentile of life time risk was calculated to be 9.74E-06, 4.39E-05 and 2.12E-04, respectively.

Adsorption characteristics of 210Pb, 210Po and 7Be onto micro-particle surfaces and the effects of macromolecular organic compounds

NASA Astrophysics Data System (ADS)

Yang, Weifeng; Guo, Laodong; Chuang, Chia-Ying; Schumann, Dorothea; Ayranov, Marin; Santschi, Peter H.

2013-04-01

210Po, 210Pb and Be isotopes (e.g. 7Be and 10Be) have long been used as proxies of particle/sediment dynamics, carbon cycling, and oceanographic investigations of coupled processes. However, adsorption characteristics and interactions between these nuclides and particle surfaces remain poorly understood. Laboratory studies have been conducted to examine the adsorption of 210Po, 210Pb and 7Be onto micro-particles, including marine suspended particulate matter, kaolinite, Al2O3, SiO2, CaCO3, Fe2O3, MnO2, and chitin in natural seawater (<1 kDa), and the role of macromolecular organic compounds (MOCs), including humic acids (HA), acid polysaccharides (APS) and proteins (BSA) in regulating the adsorption process. In the absence of MOCs, the partition coefficients (Kd, reported in log Kd) range from 3.02 to 5.19 for 210Po, from 3.22 to 6.29 for 210Pb, and from 3.57 to 4.65 for 7Be. Ferric and manganese oxides are the strongest sorbents of 210Po and 210Pb, comparing with SiO2 and CaCO3. In the presence of the protein BSA, both SiO2 and CaCO3 preferentially adsorb 210Po over 210Pb, whereas the opposite effect was observed in the presence of acid polysaccharides, indicating that proteins could enhance the adsorption of 210Po and acid polysaccharides enhance the adsorption of 210Pb. The log Kd values of both 210Po and 210Pb in the presence of MOCs become similar (log Kd at ˜4.0) for all lithogenic and biogenic particles, suggesting that their adsorption is likely controlled by specific natural organic compounds associated with particle surfaces. For 7Be, the highest and lowest log Kd value was measured, in general, on SiO2 and CaCO3, respectively, consistent with field observations. Nevertheless, the log Kd values of 7Be varied little between particle types regardless of the presence or absence of MOCs, suggesting that the adsorption of Be on particle surfaces is less affected by particle composition or MOCs. These results indicate that 7Be and 10Be could quantitatively track the bulk particles and their fluxes in marine environments while both 210Po and 210Pb could be quantitative proxies for the bulk organic carbon, although 210Po and 210Pb could be fractionated by specific organic compounds during their sorption or scavenging on particle surfaces.

Modeling the acid-base properties of bacterial surfaces: A combined spectroscopic and potentiometric study of the gram-positive bacterium Bacillus subtilis.

PubMed

Leone, Laura; Ferri, Diego; Manfredi, Carla; Persson, Per; Shchukarev, Andrei; Sjöberg, Staffan; Loring, John

2007-09-15

In this study, macroscopic and spectroscopic data were combined to develop a surface complexation model that describes the acid-base properties of Bacillus subtilis. The bacteria were freeze-dried and then resuspended in 0.1 M NaCl ionic medium. Macroscopic measurements included potentiometric acid-base titrations and electrophoretic mobility measurements. In addition, ATR-FTIR spectra of wet pastes from suspensions of Bacillus subtilis at different pH values were collected. The least-squares program MAGPIE was used to generate a surface complexation model that takes into account the presence of three acid-base sites on the surface: tripple bond COOH, tripple bond NH+, and tripple bond PO-, which were identified previously by XPS measurements. Both potentiometric titration data and ATR-FTIR spectra were used quantitatively, and electrostatic effects at the charged bacterial surface were accounted for using the constant capacitance model. The model was calculated using two different approaches: in the first one XPS data were used to constrain the ratio of the total concentrations of all three surface sites. The capacitance of the double layer, the total buffer capacity, and the deprotonation constants of the tripple bond NH+, tripple bond POH, and tripple bond COOH species were determined in the fit. A second approach is presented in which the ratio determined by XPS of the total concentrations of tripple bond NH+ to tripple bond PO- sites is relaxed. The total concentration of tripple bond PO- sites was determined in the fit, while the deprotonation constant for tripple bond POH was manually varied until the minimization led to a model which predicted an isoelectric point that resulted in consistency with electrophoretic mobility data. The model explains well the buffering capacity of Bacillus subtilis suspensions in a wide pH range (between pH=3 and pH=9) which is of considerable environmental interest. In particular, a similar quantitative use of the IR data opens up possibilities to model other bacterial surfaces at the laboratory scale and help estimate the buffering capacity of carboxylate-containing compounds in natural samples.

Room model based Monte Carlo simulation study of the relationship between the airborne dose rate and the surface-deposited radon progeny.

PubMed

Sun, Kainan; Field, R William; Steck, Daniel J

2010-01-01

The quantitative relationships between radon gas concentration, the surface-deposited activities of various radon progeny, the airborne radon progeny dose rate, and various residential environmental factors were investigated through a Monte Carlo simulation study based on the extended Jacobi room model. Airborne dose rates were calculated from the unattached and attached potential alpha-energy concentrations (PAECs) using two dosimetric models. Surface-deposited (218)Po and (214)Po were significantly correlated with radon concentration, PAECs, and airborne dose rate (p-values <0.0001) in both non-smoking and smoking environments. However, in non-smoking environments, the deposited radon progeny were not highly correlated to the attached PAEC. In multiple linear regression analysis, natural logarithm transformation was performed for airborne dose rate as a dependent variable, as well as for radon and deposited (218)Po and (214)Po as predictors. In non-smoking environments, after adjusting for the effect of radon, deposited (214)Po was a significant positive predictor for one dose model (RR 1.46, 95% CI 1.27-1.67), while deposited (218)Po was a negative predictor for the other dose model (RR 0.90, 95% CI 0.83-0.98). In smoking environments, after adjusting for radon and room size, deposited (218)Po was a significant positive predictor for one dose model (RR 1.10, 95% CI 1.02-1.19), while a significant negative predictor for the other model (RR 0.90, 95% CI 0.85-0.95). After adjusting for radon and deposited (218)Po, significant increases of 1.14 (95% CI 1.03-1.27) and 1.13 (95% CI 1.05-1.22) in the mean dose rates were found for large room sizes relative to small room sizes in the different dose models.

Study on the formation of dodecagonal pyramid on nitrogen polar GaN surface etched by hot H3PO4

NASA Astrophysics Data System (ADS)

Qi, S. L.; Chen, Z. Z.; Fang, H.; Sun, Y. J.; Sang, L. W.; Yang, X. L.; Zhao, L. B.; Tian, P. F.; Deng, J. J.; Tao, Y. B.; Yu, T. J.; Qin, Z. X.; Zhang, G. Y.

2009-08-01

Hot phosphor acid (H3PO4) etching is presented to form a roughened surface with dodecagonal pyramids on laser lift-off N face GaN grown by metalorganic chemical vapor deposition. A detailed analysis of time evolution of surface morphology is described as a function of etching temperature. The activation energy of the H3PO4 etching process is 1.25 eV, indicating the process is reaction-limited scheme. And it is found that the oblique angle between the facets and the base plane increases as the temperature increases. Thermodynamics and kinetics related factors of the formation mechanism of the dodecagonal pyramid are also discussed. The light output power of a vertical injection light-emitting-diode (LED) with proper roughened surface shows about 2.5 fold increase compared with that of LED without roughened surface.

An assessment of the (210)Po ingestion dose due to the consumption of agricultural, marine, fresh water and forest foodstuffs in Gudalore (India).

PubMed

Sivakumar, R

2014-11-01

The activity concentration of (210)Po in cereals, pulses, food materials of animal origin, vegetables and spices collected from Gudalore (India) has been estimated by radiochemical method. The activity concentration of (210)Po in cereals is found to vary from 124 to 604 mBq kg(-1). Raw rice registered the highest mean activity 504 ± 61 mBq kg(-1). In pulses (210)Po activity concentration varies from 42 to 320 mBq kg(-1) and the highest activity is found in black lentil with the average value of 172 ± 38 mBq kg(-1). Leafy vegetables registered the highest (210)Po activity concentration (662-7336 mBq kg(-1)) and are followed by tuber vegetables (390-1269 mBq kg(-1)) and then by other vegetables (75-595 mBq kg(-1)). The higher concentration of (210)Po observed in leafy vegetables may be attributed to the dry deposition of (210)Po and other daughter products of (222)Rn on large leaf surfaces from the air. Among animal products fish of marine origin registered the highest (210)Po activity concentration 36,850-48,964 mBq kg(-1). The mean (210)Po activity concentration in coffee has been estimated as 7500 mBq kg(-1). The activity concentration of (210)Po in leaf and bark of tree Cinnamom zeylanicum, a popular spice, is found to vary from 3500 to 11,100 mBq kg(-1) and 1600-3400 mBq kg(-1). The consumption of marine and fresh water fish contribute 60.7% (506.1 μSv y(-1)) to the total ingestion dose received. Cereals being consumed in a large scale, contribute 23.4% (194.9 μSv y(-1)) of the total ingestion dose received. The contribution from spices and leafy vegetables consumed is 5.8% (48.1 μSv y(-1)) and 6.5% (54.3 μSv y(-1)), respectively. The remaining 3.6% (30.0 μSv y(-1)) contribution to the total ingestion dose comes from other food materials and vegetables. Copyright © 2014 Elsevier Ltd. All rights reserved.

Tunable optical response of bowtie nanoantenna arrays on thermoplastic substrates

NASA Astrophysics Data System (ADS)

Sharac, N.; Sharma, H.; Veysi, M.; Sanderson, R. N.; Khine, M.; Capolino, F.; Ragan, R.

2016-03-01

Thermally responsive polymers present an interesting avenue for tuning the optical properties of nanomaterials on their surfaces by varying their periodicity and shape using facile processing methods. Gold bowtie nanoantenna arrays are fabricated using nanosphere lithography on prestressed polyolefin (PO), a thermoplastic polymer, and optical properties are investigated via a combination of spectroscopy and electromagnetic simulations to correlate shape evolution with optical response. Geometric features of bowtie nanoantennas evolve by annealing at temperatures between 105 °C and 135 °C by releasing the degree of prestress in PO. Due to the higher modulus of Au versus PO, compressive stress occurs on Au bowtie regions on PO, which leads to surface buckling at the two highest annealing temperatures; regions with a 5 nm gap between bowtie nanoantennas are observed and the average reduction is 75%. Reflectance spectroscopy and full-wave electromagnetic simulations both demonstrate the ability to tune the plasmon resonance wavelength with a window of approximately 90 nm in the range of annealing temperatures investigated. Surface-enhanced Raman scattering measurements demonstrate that maximum enhancement is observed as the excitation wavelength approaches the plasmon resonance of Au bowtie nanoantennas. Both the size and morphology tunability offered by PO allows for customizing optical response.

Surface roughness of novel resin composites polished with one-step systems.

PubMed

Ergücü, Z; Türkün, L S

2007-01-01

This study: 1) analyzed the surface roughness of five novel resin composites that contain nanoparticles after polishing with three different one-step systems and 2) evaluated the effectiveness of these polishers and their possible surface damage using scanning electron microscope (SEM) analysis. The resin composites evaluated in this study include CeramX, Filtek Supreme XT, Grandio, Premise and Tetric EvoCeram. A total of 100 discs (20/resin composites, 10 x 2 mm) were fabricated. Five specimens/resin composites cured under Mylar strips served as the control. The samples were polished for 30 seconds with PoGo, OptraPol and One Gloss discs at 15,000 rpm using a slow speed handpiece. The surfaces were tested for roughness (Ra) with a surface roughness tester and examined with SEM. One-way ANOVA was used for statistical analysis (p = 0.05). For all the composites tested, differences between the polishing systems were found to be significant (p < 0.05). For Filtek Supreme XT, Mylar and PoGo created equally smooth surfaces, while significantly rougher surfaces were obtained after OptraPol and One Gloss applications. For Grandio, Mylar and PoGo created equally smooth surfaces, while OptraPol and One Gloss produced equally rougher surfaces. Tetric EvoCeram exhibited the roughest surface with OptraPol, while no significant differences were found between Premise and CeramX. According to SEM images, OptraPol and One Gloss scratched and plucked the particles away from the surface, while PoGo created a uniform finish, although the roughness values were not the same for each composite. Effectiveness of the polishers seems to be material dependent.

Unusually large sup 210 Po deficiencies relative to sup 210 Pb in the Kuroshio Current of the East China and Philippine seas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoshiyuki Nozaki; Naoko Ikuta; Mayumi Yashima

1990-04-15

Three vertical water profiles of {sup 210}Pb and {sup 210}Po have been measured in the East China and Philippine seas. All the profiles show a large {sup 210}Po deficiency of {approximately} 8 dpm/cm{sup 2} relative to {sup 210}Pb in the top {approximately} 1,000 m of the water column. Based on the {sup 210}Po deficiency, the steady state flux for {sup 210}Po removal from the surface water is estimated to be 14 dpm cm{sup {minus}2}/yr. The {sup 210}Po/{sup 210}Pb ratio of sinking particles will be too high unless an additional source of {sup 210}Pb into the surface is accounted for. Thusmore » the large {sup 210}Po deficit is probably caused by the increased atmospheric input of {sup 210}Pb without any significant {sup 210}Po, which is focused in the Kuroshio region by isopycnal transport, and the preferential scavenging of {sup 210}Po relative to {sup 210}Pb by settling particles. The transient model calculations indicate that the model can account for the observed high excess {sup 210}Pb inventory and large {sup 210}Po deficiency in the water column if focusing of atmospherically derived {sup 210}Pb in the Kuroshio water is a factor of 2-3 more than the local input. Such lateral redistribution by the western North Pacific gyre circulation is not inconsistent with the deeper penetration and the high water column inventories of anthropogenic substances observed in this region.« less

Phosphine oxide surfactants revisited.

PubMed

Stubenrauch, Cosima; Preisig, Natalie; Laughlin, Robert G

2016-04-01

This review summarizes everything we currently know about the nonionic surfactants alkyl dimethyl (C(n)DMPO) and alkyl diethyl (C(n)DEPO) phosphine oxide (PO surfactants). The review starts with the synthesis and the general properties (Section 2) of these compounds and continues with their interfacial properties (Section 3) such as surface tension, surface rheology, interfacial tension and adsorption at solid surfaces. We discuss studies on thin liquid films and foams stabilized by PO surfactants (Section 4) as well as studies on their self-assembly into lyotropic liquid crystals and microemulsions, respectively (Section 5). We aim at encouraging colleagues from both academia and industry to take on board PO surfactants whenever possible and feasible because of their broad variety of excellent properties. Copyright © 2016 Elsevier B.V. All rights reserved.

Designing of luminescent GdPO4:Eu@LaPO4@SiO2 core/shell nanorods: Synthesis, structural and luminescence properties

NASA Astrophysics Data System (ADS)

Ansari, Anees A.; Labis, Joselito P.; Aslam Manthrammel, M.

2017-09-01

GdPO4:Eu3+ (core) and GdPO4:Eu@LaPO4 (core/shell) nanorods (NRs) were successfully prepared by urea based co-precipitation process at ambient conditions which was followed by coating with amorphous silica shell via the sol-gel chemical route. The role of surface coating on the crystal structure, crystallinity, morphology, solubility, surface chemistry and luminescence properties were well investigated by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray (EDX) analysis, Fourier Transform Infrared (FTIR), UV-Vis, and photoluminescence spectroscopy. XRD pattern revealed highly purified, well-crystalline, single phase-hexagonal-rhabdophane structure of GdPO4 crystal. The TEM micrographs exhibited highly crystalline and narrow size distributed rod-shaped GdPO4:Eu3+ nanostructures with average width 14-16 nm and typical length 190-220 nm. FTIR spectra revealed characteristic infrared absorption bands of amorphous silica. High absorbance in a visible region of silica modified core/shell/Si NRs in aqueous environment suggests the high solubility along with colloidal stability. The photoluminescence properties were remarkably enhanced after growth of undoped LaPO4 layers due to the reduction of nonradiative transition rate. The advantages of presented high emission intensity and high solubility of core/shell and core/shell/Si NRs indicated the potential applications in monitoring biological events.

Z-scheme Ag3PO4/POM/GO heterojunction with enhanced photocatalytic performance for degradation and water splitting.

PubMed

Liu, Guodong; Zhao, Xinfu; Zhang, Jian; Liu, Shaojie; Sha, Jingquan

2018-05-01

To develop solar light-driven photocatalysts with high activity and structural stability, Ag3PO4/POM/GO heterojunction has been successfully prepared by a facile method at room temperature. Ag3PO4/POM/GO shows remarkably enhanced activity and stability for photocatalytic degradation and H2 production from water-splitting under simulated solar light. The degradation rate of Ag3PO4/POM/GO is 1.8 times and 1.2 times those of Ag3PO4 and Ag3PO4/POMs, respectively. H2 production using Ag3PO4/POM/GO is 2.0 times that of Ag3PO4/GO. The enhanced photocatalytic performance of Ag3PO4/POM/GO is attributed to the increased surface area, electronegativity and structure stability. The Z-scheme system of Ag3PO4/POM/GO effectively promotes charge separation, resulting in enhanced photocatalytic performance under simulated solar light.

Diurnal variations of (218)Po, (214)Pb, and (214)Po and their effect on atmospheric electrical conductivity in the lower atmosphere at Mysore city, Karnataka State, India.

PubMed

Pruthvi Rani, K S; Paramesh, L; Chandrashekara, M S

2014-12-01

The short-lived radon daughters ((218)Po, (214)Pb, (214)Bi and (214)Po) are natural tracers in the troposphere, in particular near the ground surface. They are electrically charged particles and are chemically reactive. As soon as they are formed they get attached to the aerosol particles of the atmosphere. The behavior of radon daughters is similar to that of aerosols with respect to their growth, transport and removal processes in the atmosphere. The electrical conductivity of the atmosphere is mainly due to the presence of highly mobile ions. Galactic cosmic rays are the main source of ionization in the planetary boundary layer; however, near the surface of the earth, ions are produced mainly by decays of natural radioactive gases emanating from the soil surface and by radiations emitted directly from the surface. Hence the electrical conductivity of air near the surface of the earth is mainly due to radiations emitted by (222)Rn, (218)Po, (214)Pb, (214)Bi and (214)Po, and depends on aerosol concentrations and meteorological parameters. In the present work the diurnal and seasonal variations of radon and its progeny concentrations are studied using Low Level Radon Detection System and Airflow Meter respectively. Atmospheric electrical conductivity of both positive and negative polarities is measured using a Gerdien Condenser. All the measurements were carried out simultaneously at one location in Mysore city (12°N, 76°E), India. The diurnal variation of atmospheric electrical conductivity was found to be similar to that of ion pair production rate estimated from radon and its progeny concentrations with a maximum in the early morning hours and minimum during day time. The annual average concentrations of (222)Rn, (218)Po, (214)Pb, and (214)Po at the study location were found to be 21.46, 10.88, 1.78 and 1.80 Bq m(-3) respectively. The annual average values of positive and negative atmospheric electrical conductivity were found to be 18.1 and 16.6 f S m(-1) respectively. The radon and its progeny concentrations are higher in winter than in summer and rainy season. Copyright © 2014 Elsevier Ltd. All rights reserved.

Thermophysical Properties Measurement of High-Temperature Liquids Under Microgravity Conditions in Controlled Atmospheric Conditions

NASA Technical Reports Server (NTRS)

Watanabe, Masahito; Ozawa, Shumpei; Mizuno, Akotoshi; Hibiya, Taketoshi; Kawauchi, Hiroya; Murai, Kentaro; Takahashi, Suguru

2012-01-01

Microgravity conditions have advantages of measurement of surface tension and viscosity of metallic liquids by the oscillating drop method with an electromagnetic levitation (EML) device. Thus, we are preparing the experiments of thermophysical properties measurements using the Materials-Science Laboratories ElectroMagnetic-Levitator (MSL-EML) facilities in the international Space station (ISS). Recently, it has been identified that dependence of surface tension on oxygen partial pressure (Po2) must be considered for industrial application of surface tension values. Effect of Po2 on surface tension would apparently change viscosity from the damping oscillation model. Therefore, surface tension and viscosity must be measured simultaneously in the same atmospheric conditions. Moreover, effect of the electromagnetic force (EMF) on the surface oscillations must be clarified to obtain the ideal surface oscillation because the EMF works as the external force on the oscillating liquid droplets, so extensive EMF makes apparently the viscosity values large. In our group, using the parabolic flight levitation experimental facilities (PFLEX) the effect of Po2 and external EMF on surface oscillation of levitated liquid droplets was systematically investigated for the precise measurements of surface tension and viscosity of high temperature liquids for future ISS experiments. We performed the observation of surface oscillations of levitated liquid alloys using PFLEX on board flight experiments by Gulfstream II (G-II) airplane operated by DAS. These observations were performed under the controlled Po2 and also under the suitable EMF conditions. In these experiments, we obtained the density, the viscosity and the surface tension values of liquid Cu. From these results, we discuss about as same as reported data, and also obtained the difference of surface oscillations with the change of the EMF conditions.

Adsorption mechanism of physiologically active L-phenylalanine phosphonodipeptide analogues: Comparison of colloidal silver and macroscopic silver substrates

NASA Astrophysics Data System (ADS)

Podstawka, E.; Kudelski, A.; Proniewicz, L. M.

2007-11-01

Here we present SERS spectra of several L-phenylalanine (Phe) phosphonodipeptides, i.e., L-Phe- L-Ala-PO 3H 2 ( MD1), L-Phe- L-Va L-PO 3H 2 ( MD2), L-Phe-β-Ala-CH(OH)-PO 3H 2 ( MD3), L-Phe- L-Ala-CH(OH)-PO 3H 2 ( MD4), L-Ala-(3,4-dimethoxy)- L-Phe-PO 3H 2 ( MD5), and L-Ala-(3,4-dimethoxy)-(des-CH 2)- L-Phe-PO 3H 2 ( MD6), immobilized on electrochemically roughened silver electrodes. These spectra are analyzed by theoretical calculations using density functional theory (DFT) at the B3LYP level with 6-31++G∗∗ basis set. In addition, these spectra are compared with SERS spectra of these species adsorbed on a colloidal silver surface. We showed that on the macroscopic silver substrate, the Phe aromatic ring of MD3 and MD4 is oriented vertically, while for MD1 it almost "stands up" on this surface. In the other three cases, the Phe ring adopts a tilted orientation in regard to the substrate. We also find that the phosphonate (-PO32-), methyl/methane, or dimethoxy groups of MD1, MD2, MD3, MD5, and MD6 are involved in the interaction of these phosphonodipeptides with the electrochemically roughened surface. This phenomenon is clearly seen for -CH 2-/-CH 3/-OCH 3 moieties as well as for the PO32- group that adsorbs on the macroscopic silver substrates mainly via the P dbnd O fragment. We also showed that MD4 binds to the macroscopic silver substrate through the hydroxyl, amine, and phosphonate groups, while the methylene/methane moieties are remote from this surface. We found that studied phosphonodipeptides often adsorb differently on the macroscopic silver substrate and on the colloidal silver nanoparticles. For example, MD1 adopts an almost vertical orientation on the electrochemically roughened silver substrate and is tilted or close to flat on the silver nanoparticles.

[Distribution characteristics and correlations of phosphorus in sediment and interstitial water of Nansi Lake, Shandong Province of East China in summer and winter].

PubMed

Li, Bao; Wang, Zhi-Qi; Wang, Qian-Suo; Cuan, Jing-Bo

2013-06-01

By using cylindrical sediment sampler and Peeper' s interstitial water sampler, the intact sediment and interstitial water were collected from different zones of Nansi Lake in Shandong Province in summer and winter. The distribution characteristics of the sediment phosphorus forms and of the phosphate (PO4(3-)-P) in interstitial water were analyzed, and their correlations were discussed. In the sediments of Nansi Lake, phosphorus was richer, and had a significant spatial differentiation, with an overall decreasing trend from north to south, which was related to the seriously polluted Northern Nansi Lake near Jining City. Among the phosphorous forms, inorganic phosphorus (IP) had the highest concentration, accounting for 52.3%-87.2% and 60.6%-88.3% of the total phosphorus (TP) in summer and winter, respectively. The TP concentrations in 5 cm surface sediment of four sub-lakes were all higher in summer than in winter, which could be related to the human activities such as exuberant aquaculture, more chemical fertilizers application around lake, and frequent tourism activities, etc. in summer. In vertical direction, the PO4(3-)-P concentration in interstitial water decreased after an initial increase in summer and winter, and was obviously higher in summer than in winter, suggesting that the phosphorous in sediment had a higher potential to release to the overlying water in summer. The organic phosphorus (OP) and IP in sediment had a significant correlation in summer but less correlation in winter, indicating that the transformation between sediment IP and OP was more active in summer than in winter. The iron and aluminum bound phosphorus (Fe/Al-P) and IP in sediment were significantly positively correlated with the PO4(3-)-P in interstitial water. In summer and winter, the average PO4(3-)-P concentration in interstitial water collected by Peeper' s interstitial water sampler was about 20%-50% higher than that collected by the conventional centrifugal method, suggesting that using Peeper' s interstitial water sampler could be more precise.

LiFePO4 Nanostructures Fabricated from Iron(III) Phosphate (FePO4 x 2H2O) by Hydrothermal Method.

PubMed

Saji, Viswanathan S; Song, Hyun-Kon

2015-01-01

Electrode materials having nanometer scale dimensions are expected to have property enhancements due to enhanced surface area and mass/charge transport kinetics. This is particularly relevant to intrinsically low electronically conductive materials such as lithium iron phosphate (LiFePO4), which is of recent research interest as a high performance intercalation electrode material for Li-ion batteries. Many of the reported works on LiFePO4 synthesis are unattractive either due to the high cost of raw materials or due to the complex synthesis technique. In this direction, synthesis of LiFePO4 directly from inexpensive FePO4 shows promise.The present study reports LiFePO4 nanostructures prepared from iron (III) phosphate (FePO4 x 2H2O) by precipitation-hydrothermal method. The sintered powder was characterized by X-ray diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), Inductive coupled plasma-optical emission spectroscopy (ICP-OES), and Electron microscopy (SEM and TEM). Two synthesis methods, viz. bulk synthesis and anodized aluminum oxide (AAO) template-assisted synthesis are reported. By bulk synthesis, micro-sized particles having peculiar surface nanostructuring were formed at precipitation pH of 6.0 to 7.5 whereas typical nanosized LiFePO4 resulted at pH ≥ 8.0. An in-situ precipitation strategy inside the pores of AAO utilizing the spin coating was utilized for the AAO-template-assisted synthesis. The template with pores filled with the precipitate was subsequently subjected to hydrothermal process and high temperature sintering to fabricate compact rod-like structures.

Modeling the oxidative capacity of the atmosphere of the south coast air basin of California. 1. Ozone formation metrics.

PubMed

Griffin, Robert J; Revelle, Meghan K; Dabdub, Donald

2004-02-01

Metrics associated with ozone (O3) formation are investigated using the California Institute of Technology (CIT) three-dimensional air-quality model. Variables investigated include the O3 production rate (P(O3)), O3 production efficiency (OPE), and total reactivity (the sum of the reactivity of carbon monoxide (CO) and all organic gases that react with the hydroxyl radical). Calculations are spatially and temporally resolved; surface-level and vertically averaged results are shown for September 9, 1993 for three Southern California locations: Central Los Angeles, Azusa, and Riverside. Predictions indicate increasing surface-level O3 concentrations with distance downwind, in line with observations. Surface-level and vertically averaged P(O3) values peak during midday and are highest downwind; surface P(O3) values are greater than vertically averaged values. Surface OPEs generally are highest downwind and peak during midday in downwind locations. In contrast, peaks occur in early morning and late afternoon in the vertically averaged case. Vertically averaged OPEs tend to be greater than those for the surface. Total reactivities are highest in upwind surface locations and peak during rush hours; vertically averaged reactivities are smaller and tend to be more uniform temporally and spatially. Total reactivity has large contributions from CO, alkanes, alkenes, aldehydes, unsubstituted monoaromatics, and secondary organics. Calculations using estimated emissions for 2010 result in decreases in P(O3) values and reactivities but increases in OPEs.

The diving bell and the spider: the physical gill of Argyroneta aquatica.

PubMed

Seymour, Roger S; Hetz, Stefan K

2011-07-01

Argyroneta aquatica is a unique air-breathing spider that lives virtually its entire life under freshwater. It creates a dome-shaped web between aquatic plants and fills the diving bell with air carried from the surface. The bell can take up dissolved O(2) from the water, acting as a 'physical gill'. By measuring bell volume and O(2) partial pressure (P(O(2))) with tiny O(2)-sensitive optodes, this study showed that the spiders produce physical gills capable of satisfying at least their resting requirements for O(2) under the most extreme conditions of warm stagnant water. Larger spiders produced larger bells of higher O(2) conductance (G(O(2))). G(O(2)) depended on surface area only; effective boundary layer thickness was constant. Bells, with and without spiders, were used as respirometers by measuring G(O(2)) and the rate of change in P(O(2)). Metabolic rates were also measured with flow-through respirometry. The water-air P(O(2)) difference was generally less than 10 kPa, and spiders voluntarily tolerated low internal P(O(2)) approximately 1-4 kPa before renewal with air from the surface. The low P(O(2)) in the bell enhanced N(2) loss from the bell, but spiders could remain inside for more than a day without renewal. Spiders appeared to enlarge the bells in response to higher O(2) demands and lower aquatic P(O(2)).

Direct comparison of 210Po, 234Th and POC particle-size distributions and export fluxes at the Bermuda Atlantic Time-series Study (BATS) site.

PubMed

Stewart, Gillian; Moran, S Bradley; Lomas, Michael W; Kelly, Roger P

2011-05-01

Particle-reactive, naturally occurring radionuclides are useful tracers of the sinking flux of organic matter from the surface to the deep ocean. Since the Joint Global Ocean Flux Study (JGOFS) began in 1987, the disequilibrium between (234)Th and its parent (238)U has become widely used as a technique to measure particle export fluxes from surface ocean waters. Another radionuclide pair, (210)Po and (210)Pb, can be used for the same purpose but has not been as widely adopted due to difficulty with accurately constraining the (210)Po/(210)Pb radiochemical balance in the ocean and because of the more time-consuming radiochemical procedures. Direct comparison of particle flux estimated in different ocean regions using these short-lived radionuclides is important in evaluating their utility and accuracy as tracers of particle flux. In this paper, we present paired (234)Th/(238)U and (210)Po/(210)Pb data from oligotrophic surface waters of the subtropical Northwest Atlantic and discuss their advantages and limitations. Vertical profiles of total and particle size-fractionated (210)Po and (234)Th activities, together with particulate organic carbon (POC) concentrations, were measured during three seasons at the Bermuda Atlantic Time-series Study (BATS) site. Both (210)Po and (234)Th reasonably predict sinking POC flux caught in sediment traps, and each tracer provides unique information about the magnitude and efficiency of the ocean's biological pump. Copyright © 2010 Elsevier Ltd. All rights reserved.

Optimizing Phosphoric Acid plus Hydrogen Peroxide (PHP) Pretreatment on Wheat Straw by Response Surface Method for Enzymatic Saccharification.

PubMed

Qiu, Jingwen; Wang, Qing; Shen, Fei; Yang, Gang; Zhang, Yanzong; Deng, Shihuai; Zhang, Jing; Zeng, Yongmei; Song, Chun

2017-03-01

Wheat straw was pretreated by phosphoric acid plus hydrogen peroxide (PHP), in which temperature, time, and H 3 PO 4 proportion for pretreatment were investigated by using response surface method. Results indicated that hemicellulose and lignin removal positively responded to the increase of pretreatment temperature, H 3 PO 4 proportion, and time. H 3 PO 4 proportion was the most important variable to control cellulose recovery, followed by pretreatment temperature and time. Moreover, these three variables all negatively related to cellulose recovery. Increasing H 3 PO 4 proportion can improve enzymatic hydrolysis; however, reduction on cellulose recovery results in decrease of glucose yield. Extra high temperature or long time for pretreatment was not beneficial to enzymatic hydrolysis and glucose yield. Based on the criterion for minimizing H 3 PO 4 usage and maximizing glucose yield, the optimized pretreatment conditions was 40 °C, 2.0 h, and H 3 PO 4 proportion of 70.2 % (H 2 O 2 proportion of 5.2 %), by which glucose yielded 299 mg/g wheat straw (946.2 mg/g cellulose) after 72-h enzymatic hydrolysis.

Infrared-active optical phonons in LiFePO4 single crystals

NASA Astrophysics Data System (ADS)

Stanislavchuk, T. N.; Middlemiss, D. S.; Syzdek, J. S.; Janssen, Y.; Basistyy, R.; Sirenko, A. A.; Khalifah, P. G.; Grey, C. P.; Kostecki, R.

2017-07-01

Infrared-active optical phonons were studied in olivine LiFePO4 oriented single crystals by means of both rotating analyzer and rotating compensator spectroscopic ellipsometry in the spectral range between 50 and 1400 cm-1. The eigenfrequencies, oscillator strengths, and broadenings of the phonon modes were determined from fits of the anisotropic harmonic oscillator model to the data. Optical phonons in a heterosite FePO4 crystal were measured from the delithiated ab-surface of the LiFePO4 crystal and compared with the phonon modes of the latter. Good agreement was found between experimental data and the results of solid-state hybrid density functional theory calculations for the phonon modes in both LiFePO4 and FePO4.

Nanocomposite of exfoliated bentonite/g-C3N4/Ag3PO4 for enhanced visible-light photocatalytic decomposition of Rhodamine B.

PubMed

Ma, Jianfeng; Huang, Daiqin; Zhang, Wenyi; Zou, Jing; Kong, Yong; Zhu, Jianxi; Komarneni, Sridhar

2016-11-01

Novel visible-light-driven heterojunction photocatalyst comprising exfoliated bentonite, g-C3N4 and Ag3PO4 (EB/g-C3N4/Ag3PO4) was synthesized by a facile and green method. The composites EB/g-C3N4/Ag3PO4 were characterized by X-ray diffraction, Transmission electron microscopy, Fourier transform infrared spectroscopy, UV-Vis diffuse reflectance spectroscopy and the Brunauer, Emmett, and Teller (BET) surface area method. Under visible light irradiation, EB/g-C3N4/Ag3PO4 composites displayed much higher photocatalytic activity than that of either pure g-C3N4 or pure Ag3PO4 in the degradation of Rhodamine B (RhB). Among the hybrid photocatalysts, EB/g-C3N4/Ag3PO4 composite containing 20 wt% Ag3PO4 exhibited the highest photocatalytic activity for the decolorization of RhB. Under the visible-light irradiation, the RhB dye was completely decolorized in less than 60 min. The enhanced photocatalytic performance is attributed to the stable structure, enlarged surface area, strong adsorbability, strong light absorption ability, and high-efficiency separation rate of photoinduced electron-hole pairs. Our finding paves a way to design highly efficient and stable visible-light-induced photocatalysts for practical applications in wastewater treatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Monitoring of impact of anthropogenic inputs on water quality of mangrove ecosystem of Uran, Navi Mumbai, west coast of India.

PubMed

Pawar, Prabhakar R

2013-10-15

Surface water samples were collected from substations along Sheva creek and Dharamtar creek mangrove ecosystems of Uran (Raigad), Navi Mumbai, west coast of India. Water samples were collected fortnightly from April 2009 to March 2011 during spring low and high tides and were analyzed for pH, Temperature, Turbidity, Total solids (TS), Total dissolved solids (TDS), Total suspended solids (TSS), Dissolved oxygen (DO), Biochemical oxygen demand (BOD), Carbon dioxide (CO2), Chemical oxygen demand (COD), Salinity, Orthophosphate (O-PO4), Nitrite-nitrogen (NO2-N), Nitrate-nitrogen (NO3-N), and Silicates. Variables like pH, turbidity, TDS, salinity, DO, and BOD show seasonal variations. Higher content of O-PO4, NO3-N, and silicates is recorded due to discharge of domestic wastes and sewage, effluents from industries, oil tanking depots and also from maritime activities of Jawaharlal Nehru Port Trust (JNPT), hectic activities of Container Freight Stations (CFS), and other port wastes. This study reveals that water quality from mangrove ecosystems of Uran is deteriorating due to industrial pollution and that mangrove from Uran is facing the threat due to anthropogenic stress. Copyright © 2013 Elsevier Ltd. All rights reserved.

Impact of the Clean Water Act on the levels of toxic metals in urban estuaries: The Hudson River estuary revisited

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanudo-Wilhelmy, S.A.; Gill, G.A.

1999-10-15

To establish the impact of the Clean Water Act on the water quality of urban estuaries, dissolved trace metals and phosphate concentrations were determined in surface waters collected along the Hudson River estuary between 1995 and 1997 and compared with samples collected in the mid-1970s by Klinkhammer and Bender. The median concentrations along the estuary have apparently declined 36--56% for Cu, 55--89% for Cd, 53--85% for Ni, and 53--90% for Zn over a period of 23 years. These reductions appear to reflect improvements in controlling discharges from municipal and industrial wastewater treatment plants since the Clean Water Act was enactedmore » in 1972. In contrast, levels of dissolved nutrients (PO{sub 4}) have remained relatively constant during the same period of time, suggesting that wastewater treatment plant improvements in the New York/New Jersey Metropolitan area have not been as effective at reducing nutrient levels within the estuary. While more advanced wastewater treatment could potentially reduce the levels of Ag and PO{sub 4} along the estuary, these improvements would have a more limited effect on the levels of other trace metals.« less

Hydroxyapatite crystallization from a highly concentrated phosphate solution using powdered converter slag as a seed material.

PubMed

Kim, Eung-Ho; Yim, Soo-Bin; Jung, Ho-Chan; Lee, Eok-Jae

2006-08-25

A system for recovering phosphorus from membrane-filtrate from a sludge reduction process containing high phosphorus concentrations was developed. In this system, referred to as the completely mixed phosphorus crystallization reactor, powdered converter slag was used as a seed material. In a preliminary experiment, the optimal pH range for metastable crystallization of phosphorus from membrane-filtrate containing about 100mg/L PO(4)-P was found to be 6.6-7.0. The laboratory scale completely mixed phosphorus crystallization reactor, actually operated in pH range of 6.8-7.6 for influent 72.9 mg/L PO(4)-P, achieved an average efficiency of phosphorus removal from the membrane-filtrate of 52.4% during a 30-day experiment. Mixed-liquor suspended solids (MLSS) measurements revealed that, out of 0.24 kg PO(4)-P in the original membrane-filtrate fed into the reactor, 0.12 kg PO(4)-P was recovered on the seed particles after 30 days. X-ray diffraction (XRD) pattern and Fourier transform infrared (FT-IR) spectra of the crystalline material deposited on the seed particles showed peaks consistent with hydroxyapatite. Scanning electron micrograph (SEM) images exhibited that finely distributed crystalline material was formed on the surfaces of seed particles. Energy dispersive X-ray spectroscopy (EDS) mapping analysis revealed that the molar composition ratio of Ca/P of the crystalline material was 1.84. The Ca/P molar ratio>1.67 for crystalline substance might result from the presence of CaCO(3) on the crystalline surfaces. A particle size distribution analysis showed that the average particle size increased from 22 microm for the original converter slag seed particles, to 94 microm after 30 days of phosphorus crystallization. Collectively, the present results suggest that the proposed phosphorus crystallization recovery system is an effective tool for recycling phosphorus from phosphate solution.

Emergence of Metallic Properties at LiFePO4 Surfaces and LiFePO4/Li2S Interfaces: An Ab Initio Study.

PubMed

Timoshevskii, Vladimir; Feng, Zimin; Bevan, Kirk H; Zaghib, Karim

2015-08-26

The atomic and electronic structures of the LiFePO4 (LFP) surface, both bare and reconstructed upon possible oxygenation, are theoretically studied by ab initio methods. On the basis of total energy calculations, the atomic structure of the oxygenated surface is proposed, and the effect of surface reconstruction on the electronic properties of the surface is clarified. While bare LFP(010) surface is insulating, adsorption of oxygen leads to the emergence of semimetallic behavior by inducing the conducting states in the band gap of the system. The physical origin of these conducting states is investigated. We further demonstrate that deposition of Li2S layers on top of oxygenated LFP(010) surface leads to the formation of additional conducting hole states in the first layer of Li2S surface because of the charge transfer from sulfur p-states to the gap states of LFP surface. This demonstrates that oxygenated LFP surface not only provides conducting layers itself, but also induces conducting channels in the top layer of Li2S. These results help to achieve further understanding of potential role of LFP particles in improving the performance of Li-S batteries through emergent interface conductivity.

A Powder Delivery System (PoDS) for Mars in situ Science

NASA Astrophysics Data System (ADS)

Bryson, C.; Blake, D.; Saha, C.; Sarrazin, P.

2004-12-01

Many instruments proposed for in situ Mars science investigations work best with fine-grained samples of rocks or soils. Such instruments include the mineral analyzer CheMin [1] and any instrument that requires samples having high surface areas (e.g., mass spectrometers, organic analyzers, etc). The Powder Delivery System (PoDS) is designed to deliver powders of selected grain sizes from a sample acquisition device such as an arm-deployed robotic driller or corer to an instrument suite located on the body of a rover/lander. PoDS is capable of size-selective sampling of crushed rocks, soil or drill powder for delivery to instruments that require specific grain sizes (e.g. 5-50 mg of less than150 micron powder for CheMin). Sample material is transported as an aerosol of particles and gas by vacuum advection. In the laboratory a venturi pump driven by compressed air provides the impulse. On Mars, the ambient atmosphere is a source of CO2 that can be captured and compressed by adsorption pumping during diurnal temperature cycling [2]. The lower atmospheric pressure on the surface of Mars (7 torr) will affect fundamental parameters of gas-particle interaction such as Reynolds, Stocks and Knudsen numbers [3]. However, calculations show that the PoDS will operate under both Martian and terrestrial atmospheric conditions. Cyclone separators with appropriate particle size selection ranges remove particles from the aerosol stream. The vortex flow inside the cyclone causes grains larger than a specific size to be collected, while smaller grains remain entrained in the gas. Cyclones are very efficient inertial and centrifugal particle separators with cut sizes (d50) as low as 4 microns. Depending on the particle size ranges desired, a series of cyclones with descending cut sizes may be used, the simplest case being a single cyclone for particle deposition without mass separation. Transmission / membrane filters of appropriate pore sizes may also be used to collect powder from the aerosol stream. Results of a number of tests of the prototype PoDS will be presented. [1] Blake D. F., Sarrazin P., Bish D. L., Feldman S., Chipera S. J, Vaniman D.T., and Collins S., 2004, Definitive Mineralogical Analysis of Mars Analog Rocks Using the CheMin XRD/XRF Instrument, LPSC XXXV abstr. #1794 (CD-ROM). [2] Finn J. E., McKay C. P. and Sridhar R. K., 1999, Martian Atmosphere Utilization by Temperature-Swing Adsorption, University of Arizona, Publication No.961597, http://stl.ame.arizona.edu/publications/961597.pdf [3] Hinds W. C., 1999, Aerosol Technology - Properties, Behavior, and Measurement of Airborne Particles, Second edition, John Wiley & Sons, Inc., pp 15-67, 111-136.

Fluorometric determination of the activity of alkaline phosphatase based on the competitive binding of gold nanoparticles and pyrophosphate to CePO4:Tb nanorods.

PubMed

Xu, Ai-Zhen; Zhang, Li; Zeng, Hui-Hui; Liang, Ru-Ping; Qiu, Jian-Ding

2018-05-09

A fluorometric method is described for the determination of the activity of alkaline phosphatase (ALP). It relies on the competition between gold nanoparticles (AuNPs) and pyrophosphate (PPi) for the coordination sites on the surface of CePO 4 :Tb nanorods. The green fluorescence of the CePO 4 :Tb is reduced in the presence of AuNPs due to fluorescence resonance energy transfer (FRET), but can be restored on addition of PPi due to the stronger affinity of PPi to the CePO 4 :Tb. In the presence of ALP, PPi is hydrolyzed to form phosphate which has much weaker affinity for the CePO 4 :Tb. Hence, the AuNPs will reassemble on the CePO 4 :Tb, and fluorescence is reduced. Fluorescence drops linearly in the 0.2 to 100 U·L -1 activity range, and the detection limit is 60 mU·L -1 (at S/N = 3). The method does not require any modification of the surface of the CePO 4 :Tb and is highly sensitive and selective. The inhibition of ALP activity by Na 3 VO 4 was also studied. In our perception, the method may find application in the diagnosis of ALP-related diseases, in screening for inhibitors, and in studies on ALP-related functions in biological systems. Graphical abstract A assay for the detection of alkaline phosphatase is proposed based on the fluorescence resonance energy transfer between CePO 4 :Tb and AuNPs. It relies on the competitive binding of AuNPs and pyrophosphate (PPi) to CePO 4 :Tb and the hydrolysis of PPi by ALP.

Polonium problem in lead-bismuth flow target

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pankratov, D.V.; Yefimov, E.I.; Bugreev, M.I.

1996-06-01

Alpha-active polonium nuclides Po198 - Po210 are formed in a lead-bismuth target as results of reactions Bi{sup 209}(n,{gamma})Bi{sup 210} {yields} Po{sup 210}, Bi{sup 209}(p,xn)Po{sup 210} {yields} Po{sup 210 {minus} x} (x = 1-12), Pb{sup 208}({alpha},xn) {yields} Po{sup 210 {minus} x + 2} (x = 2-14). The most important nuclides are Po-210 (T{sub {1/2}}=138.4 day), Po-209 (T{sub {1/2}}=102 years) and Po-208 (T{sub {1/2}}=2.9 years). Polonium activity of the circuit for SINQ - conditions is about 15,000 Ci after 1-year operation. Polonium radiation hazard is connected with its output from the coolant and formation of aerosol and surface alpha-activity after the circuitmore » break-down for repair works or in accidents. One of the important issues of polonium removal system creation is containing and storing polonium removed. Its storage in solidified alkaline is not expedient because of secondary neutron formation as a result of ({alpha},n) - reaction on oxygen and sodium nucleus. The estimations carried out demonstrated that by polonium concentration {approx} 100 Ci/l neutron current on the container surface can reach {approx} 10{sup 4}n/(cm{sup 2}s). Concentration and storage of polonium in solidified lead-bisumth seems the most convenient. The calculations demonstrated that in a 100 l container 50,000 Ci of polonium can be stored (as much as 3 times more than 1-year polonium product in SINQ-conditions) under temperature in the container less than melting point of lead bismuth (the wall temperature is about 100{degrees}C).« less

Infrared-active optical phonons in LiFePO 4 single crystals

DOE PAGES

Stanislavchuk, T. N.; Middlemiss, D. S.; Syzdek, J. S.; ...

2017-07-28

Infrared-active optical phonons were studied in olivine LiFePO 4 oriented single crystals by means of both rotating analyzer and rotating compensator spectroscopic ellipsometry in the spectral range between 50 and 1400 cm -1. The eigenfrequencies, oscillator strengths, and broadenings of the phonon modes were determined from fits of the anisotropic harmonic oscillator model to the data. Optical phonons in a heterosite FePO 4 crystal were measured from the delithiated ab-surface of the LiFePO 4 crystal and compared with the phonon modes of the latter. Good agreement was found between experimental data and the results of solid-state hybrid density functional theorymore » calculations for the phonon modes in both LiFePO 4 and FePO 4.« less

Photocatalytic activity of attapulgite-TiO2-Ag3PO4 ternary nanocomposite for degradation of Rhodamine B under simulated solar irradiation

NASA Astrophysics Data System (ADS)

He, Hongcai; Jiang, Zhuolin; He, Zhaoling; Liu, Tao; Li, Enzhu; Li, Bao-Wen

2018-01-01

An excellent ternary composite photocatalyst consisting of silver orthophosphate (Ag3PO4), attapulgite (ATP), and TiO2 was synthesized, in which heterojunction was formed between dissimilar semiconductors to promote the separation of photo-generated charges. The ATP/TiO2/Ag3PO4 composite was characterized by SEM, XRD, and UV-vis diffuse reflectance spectroscopy. The co-deposition of Ag3PO4 and TiO2 nanoparticles onto the surface of ATP forms a lath-particle structure. Compared with composite photocatalysts consisting of two phases, ATP/TiO2/Ag3PO4 ternary composite exhibits greatly improved photocatalytic activity for degradation of rhodamine B under simulated solar irradiation. Such ternary composite not only improves the stability of Ag3PO4, but also lowers the cost by reducing application amount of Ag3PO4, which provides guidance for the design of Ag3PO4- and Ag-based composites for photocatalytic applications.

Facile Synthesis of Bowl-Like LiFePO4/C Composite with High Rate-Performance

NASA Astrophysics Data System (ADS)

Jing, Peng; Yao, Lei; Xiang, Mingwu; Wang, Yan; Wu, Jinhua; Wang, Boya; Zhang, Yun; Wu, Hao; Liu, Heng

2018-07-01

Olivine-structured LiFePO4/C composites with high rate-performance were synthesized via an industrial spray-drying technique using a low cost Fe3O4 as iron source. The as-obtained LiFePO4/C exhibits a unique bowl-like morphology with a particle size of 2-5 μm in diameter. A continuous uniform carbon coating layer on the surface of LiFePO4/C cathodes promotes fast electron transport, whilst it guarantees the favorable electrochemical reaction. Especially the formation of porous structure leads to an average pore volume of 0.127 cm3 g-1 and a high specific surface area of 34.46 m2 g-1, which is conducive to facilitating the penetration of electrolyte and providing the more contact area of electrolyte with LiFePO4/C. As a result, the as-prepared LiFePO4/C cathode material delivers an outstanding discharge capacity of 102.1 mAh g-1, 94.2% of the initial capacity (108.3 mAh g-1), after 1000 cycles at 10 C. Even at an ultrahigh current rate of 50 C, it still shows an initial discharge capacity of 58 mAh g-1.

Facile Synthesis of Bowl-Like LiFePO4/C Composite with High Rate-Performance

NASA Astrophysics Data System (ADS)

Jing, Peng; Yao, Lei; Xiang, Mingwu; Wang, Yan; Wu, Jinhua; Wang, Boya; Zhang, Yun; Wu, Hao; Liu, Heng

2018-03-01

Olivine-structured LiFePO4/C composites with high rate-performance were synthesized via an industrial spray-drying technique using a low cost Fe3O4 as iron source. The as-obtained LiFePO4/C exhibits a unique bowl-like morphology with a particle size of 2-5 μm in diameter. A continuous uniform carbon coating layer on the surface of LiFePO4/C cathodes promotes fast electron transport, whilst it guarantees the favorable electrochemical reaction. Especially the formation of porous structure leads to an average pore volume of 0.127 cm3 g-1 and a high specific surface area of 34.46 m2 g-1, which is conducive to facilitating the penetration of electrolyte and providing the more contact area of electrolyte with LiFePO4/C. As a result, the as-prepared LiFePO4/C cathode material delivers an outstanding discharge capacity of 102.1 mAh g-1, 94.2% of the initial capacity (108.3 mAh g-1), after 1000 cycles at 10 C. Even at an ultrahigh current rate of 50 C, it still shows an initial discharge capacity of 58 mAh g-1.

The highly selective oxidation of cyclohexane to cyclohexanone and cyclohexanol over VAlPO4 berlinite by oxygen under atmospheric pressure.

PubMed

Hong, Yun; Sun, Dalei; Fang, Yanxiong

2018-04-04

The oxidation of cyclohexane under mild conditions occupies an important position in the chemical industry. A few soluble transition metals were widely used as homogeneous catalysts in the industrial oxidation of cyclohexane. Because heterogeneous catalysts are more manageable than homogeneous catalysts as regards separation and recycling, in our study, we hydrothermally synthesized and used pure berlinite (AlPO 4 ) and vanadium-incorporated berlinite (VAlPO 4 ) as heterogeneous catalysts in the selective oxidation of cyclohexane with molecular oxygen under atmospheric pressure. The catalysts were characterized by means of by XRD, FT-IR, XPS and SEM. Various influencing factors, such as the kind of solvents, reaction temperature, and reaction time were investigated systematically. The XRD characterization identified a berlinite structure associated with both the AlPO 4 and VAlPO 4 catalysts. The FT-IR result confirmed the incorporation of vanadium into the berlinite framework for VAlPO 4 . The XPS measurement revealed that the oxygen ions in the VAlPO 4 structure possessed a higher binding energy than those in V 2 O 5 , and as a result, the lattice oxygen was existed on the surface of the VAlPO 4 catalyst. It was found that VAlPO 4 catalyzed the selective oxidation of cyclohexane with molecular oxygen under atmospheric pressure, while no activity was detected on using AlPO 4 . Under optimum reaction conditions (i.e. a 100 mL cyclohexane, 0.1 MPa O 2 , 353 K, 4 h, 5 mg VAlPO 4 and 20 mL acetic acid solvent), a selectivity of KA oil (both cyclohexanol and cyclohexanone) up to 97.2% (with almost 6.8% conversion of cyclohexane) was obtained. Based on these results, a possible mechanism for the selective oxidation of cyclohexane over VAlPO 4 was also proposed. As a heterogeneous catalyst VAlPO 4 berlinite is both high active and strong stable for the selective oxidation of cyclohexane with molecular oxygen. We propose that KA oil is formed via a catalytic cycle, which involves activation of the cyclohexane by a key active intermediate species, formed from the nucleophilic addition of the lattice oxygen ion with the carbon in cyclohexane, as well as an oxygen vacancy formed at the VAlPO 4 catalyst surface.

Development of surface functionalized ZnO-doped LiFePO4/C composites as alternative cathode material for lithium ion batteries

NASA Astrophysics Data System (ADS)

Saroha, Rakesh; Panwar, Amrish K.; Sharma, Yogesh; Tyagi, Pawan K.; Ghosh, Sudipto

2017-02-01

Surface modified olivine-type LiFePO4/C-ZnO doped samples were synthesized using sol-gel assisted ball-milling route. In this work, the influence of ZnO-doping on the physiochemical, electrochemical and surface properties such as charge separation at solid-liquid interphase, surface force gradient, surface/ionic conductivity of pristine LiFePO4/C (LFP) has been investigated thoroughly. Synthesized samples were characterized using X-ray diffraction, scanning electron microscopy, atomic force microscopy, and transmission electron microscopy. All the synthesized samples were indexed to the orthorhombic phase with Pnma space group. Pristine LiFePO4 retain its structure for higher ZnO concentrations (i.e. 2.5 and 5.0 wt.% of LFP). Surface topography and surface force gradient measurements by EFM revealed that the kinetics of charge carriers, e-/Li+ is more in ZnO-doped LFP samples, which may be attributed to diffusion or conduction process of the charges present at the surface. Among all the synthesized samples LFP/C with 2.5 wt.% of ZnO (LFPZ2.5) displays the highest discharge capacity at all C-rates and exhibit excellent rate performance. LFPZ2.5 delivers a specific discharge capacity of 164 (±3) mAh g-1 at 0.1C rate. LFPZ2.5 shows best cycling performance as it provides a discharge capacity of 135 (±3) mAh g-1 at 1C rate and shows almost 95% capacity retention after 50 charge/discharge cycles. Energy density plot shows that LFPZ2.5 offers high energy and power density measured at high discharge rates (5C), proving its usability for hybrid vehicles application.

Linking the distribution of (210)Po and (210)Pb with plankton community along Line P, Northeast Subarctic Pacific.

PubMed

Choi, Hiu Yan; Stewart, Gillian M; Lomas, Michael W; Kelly, Roger P; Moran, S Bradley

2014-12-01

Depth profiles of (210)Po and (210)Pb activity and phytoplankton and zooplankton abundance were collected during two cruises along the Canadian time-series Line P in the Northeast Subarctic Pacific (ranging from 48o39 N to 50o00 N and 126o40 W to 145o00 W) in August 2010 and February 2011 to evaluate connections between the planktonic community and distributions of these radionuclides in the upper 500 m of the water column. Statistical analysis indicates that (210)Po is more effectively removed from the surface ocean when large (>0.1 mg ind(-1) dry wt) zooplankton dominate, and is less effectively scavenged when the picoplankton Synechococcus is present at high concentrations (>1 × 10(5) cells ml(-1)). While the zooplankton field data are consistent with previous lab studies and field observations, the phytoplankton results seem to conflict with recent evidence that small cells may contribute significantly to export in other oligotrophic regions. Differences in ecosystem mechanisms between the Subarctic Pacific and other oligotrophic systems that limit the contribution of small cells to sinking flux remain to be identified. Copyright © 2014 Elsevier Ltd. All rights reserved.

Polonium in size fractionated mainstream cigarette smoke, predicted deposition and associated internal radiation dose.

PubMed

Tiwari, M; Sahu, S K; Bhangare, R C; Pandit, G G

2016-10-01

In this study, size fractionated mass and 210 Po activity concentrations in mainstream cigarette smoke (MCS) were monitored for three popular cigarette brands. Size segregated collection of MCS was carried out using a cascade type impactor, while mass and 210 Po activity concentration were analyzed gravimetrically and alpha spectrometry (following the radiochemical separation) respectively. Multiple-Path Particle Dosimetry (MPPD V2.11) model is used for prediction of deposition fraction calculations for the MCS deposition in different compartment of human respiratory tract. The activity concentration of 210 Po is founds 10.56 ± 2.46 mBq per cigarette for the tested cigarette brands. 210 Po size distribution indicates most of this associates with fine fraction (Dp < 2.23 μm) of cigarette smoke. The committed annual effective dose to smokers (smoking on an average 20 cigarette a day), considering the 210 Po and 210 Pb concentrations (assuming it is in secular equilibrium with 210 Po) in MCS, was estimated between 0.22 and 0.40 mSv, with mean value of 0.30 mSv for tested cigarette brands. Considering the risk factor of fatal cancer due to radiation exposure of lung (exposure time of 30 years); the average collective estimated fatal cancer risk is estimated as 1.5 × 10 -4 due to 210 Po and 210 Pb exposure to smokers. Copyright © 2016. Published by Elsevier Ltd.

Root growth of Cynodon dactylon and Eleusine indica collected from motorways at different concentrations of lead.

PubMed

Wong, M H; Lau, W M

1985-04-01

An ecological survey was conducted on the roadside vegetation at three different sites: Tai Po, a commercial and residential area (average annual daily traffic (AADT) = 23730; and Shek O and Wu Kai Sha, recreational areas (AADT = 1590 and 20, respectively). Cynodon dactylon and Eleusine indica were the two most dominant species recorded. The Tai Po site had higher Pb contents in both soil and plant, followed by Shek O, and then Wu Kai Sha. Tillers of C. dactylon and E. indica from the three sites were subjected to a series concentrations of Pb(NO3)2. By comparing their indexes of tolerance and values of 14-day EC50 (effective concentration reducing the normal root growth by 50%), roadside populations of the two grasses collected from Tai Po and Shek O, especially the former one, were more tolerant to elevated levels of Pb compared with those collected from Wu Kai Sha.

Degassing dynamics at Mount Etna inferred from radioactive disequilibria (210Pb-210Bi-210Po) in volcanic gases

NASA Astrophysics Data System (ADS)

Terray, Luca; Gauthier, Pierre-Jean; Salerno, Giuseppe; La Spina, Alessandro; Giammanco, Salvatore; Sellitto, Pasquale; Briole, Pierre

2016-04-01

Volcanic gases are significantly enriched in the last short-half-life radionuclides of the 238U series, namely the so-called Radon daughters 210Pb, 210Bi and 210Po. Because of their contrasted volatilities, these isotopes are strongly fractionated upon degassing, which gives rise to significant radioactive disequilibria between them in the gas phase. These disequilibria carry precious information on shallow degassing processes beneath active volcanoes: they remarkably constrain the magma residence time in the degassing reservoir and the duration of gas extraction from magma to surface. On Mount Etna (Sicily), where the study of these disequilibria was initiated thirty years ago (Lambert et al., EPSL, 1985-86), no measurement of 210Pb, 210Bi and 210Po in the gases has been performed for the last twenty years. Here we present new 210Pb-210Bi-210Po radioactive disequilibria measurements in volcanic plume gases of Mount Etna. Samples were collected in the bulk diluted plume at kilometric distance from the summit area during the May 2015 eruption, then in more concentrated plumes arising from each summit crater of Etna during quiescent degassing in July 2015. We found values of (210Bi/210Pb) = 7.0 ± 0.3 and (210Po/210Pb) = 80 ± 6 during both periods. These results suggest that 210Pb, 210Bi and 210Po are not significantly fractionated during the transport of the plume from the crater rim to close-downslope sites (<1 km). None of the previous degassing models (Lambert et al., EPSL, 1985-86 ; Gauthier et al., JVGR, 2000) satisfactorily explain measured activity ratios. We propose here a new degassing model based on the previous conceptualization designed for basaltic open-conduit volcanoes, like Stromboli. This model considers extreme Radon enrichments in volcanic gases as a source of 210Pb atoms produced by radioactive decay of 222Rn within gas bubbles travelling to surface. We constrain a magma residence time of 470 ± 170 days and an extraction time of the gases of 4.9 ± 0.8 days. Along with SO2 fluxes, we also derive a volume of the degassing reservoir of 0.2-0.6 km3 in good agreement with previous estimates. Results gathered from these campaigns have intriguing implication for potential routine survey of the plume radioactivity, as part of the monitoring network of active volcanoes.

Spatial distribution of 214Po ions in the electrostatic collection.

PubMed

Barlas, E; Bayrak, A; Emirhan, E; Haciomeroglu, S; Ozben, C S

2013-10-01

A low cost Si-PIN photodiode-based radon monitor was successfully designed and produced to monitor precursory earthquake indicators in the Northern Anatolian Fault Line. The spatial distribution of (214)Po ions was determined by comparing the 7.69 MeV (214)Po peak in the MCA spectrum and the Geant4 energy distribution of alpha particles at various detector source distances. Copyright © 2013 Elsevier Ltd. All rights reserved.

Measurement of radiation exposure of astronauts by radiochemical techniques

NASA Technical Reports Server (NTRS)

Brodzinski, R. L.

1972-01-01

Only two of the fecal specimens collected inflight during the Apollo 15 mission were returned for analysis. Difficulty in obtaining reasonably accurate radiation dose estimates based on the cosmogenic radionuclide content of the specimens was encountered due to the limited sampling. The concentrations of Na-22, K-40, Cr-51, Fe-59, and Cs-137 are reported. The concentrations of 24 major, minor, and trace elements in these two specimens were determined. Most concentrations are typical of those observed previously. Major exceptions are extremely low values for selenium and extraordinarily high values for rare earth elements. The net Po-210 activities in the Apollo 11 and 12 Solar Wind Composition foils and in the Apollo 8 and 12 spacecraft reflective coatings due to lunar exposure have been determined. Equilibrium concentrations of 0.082 + or - 0.012 disintegrations /sq cm sec of Rn-222 in the lunar atmosphere and 0.0238 + or - 0.0035 disintegrations /sq cm sec of Po-210 on the lunar surface have been calculated for Oceanus Procellarum.

Ingestion of polonium ((210)Po) via dietary sources in high background radiation areas of south India.

PubMed

Arunachalam, Kantha Deivi; Baskaran, Kamesh Viswanathan; Rao, D D; Sathyapriya, R; Annamalai, Sathesh Kumar; Kuruva, Jaya Krishna; Hari, Shanmugamsundaram

2014-10-01

To study the distribution of Polonium ((210)Po) activity in dietary sources in the high background radiation zone of Puttetti in southern Tamil Nadu. (210)Po was analyzed in the food materials consumed by the male and female individual representatives living in the high background areas by 24-h Duplicate Diet Study (DDS) and Market Basket Study (MBS). The MBS was performed by collecting the food samples such as, cereals, fruits, leafy vegetables, roots and tubers, other vegetables, fish, meat and milk grown in the high background radiation zone of southern Tamil Nadu as a part of baseline study in this region. The DDS was done by collecting the food materials consumed including the beverages in 24 h from different age groups of male and female individuals living in the village of Puttetti. The intake and ingestion dose of the radionuclide (210)Po was estimated. The average concentration of (210)Po in DDS (n = 33) was found to be 74 mBq.kg(- 1) of fresh weight. The MBS was collected based on food consumption representing more than 85-95% of annual supply, and were divided into eight food groups. The average concentration of (210)Po in the eight food groups namely leafy vegetables was 2176 mBq.kg(- 1) (n = 3), vegetables 55 mBq.kg(- 1) (n = 10), roots and tubers 251 mBq.kg(- 1) (n = 4), fruits 65 mBq.kg(- 1) (n = 5), fish 345 mBq.kg(- 1) (n = 2), meat food 117 mBq.kg(- 1) (n = 3), milk 20 mBq.kg(- 1) (n = 1) and cereal 290 (n = 1) mBq.kg(- 1) of fresh weight, respectively. The annual intake and ingestion dose due to (210)Po was estimated by DDS and MBS in adults, adolescents and children. The overall results showed that the MBS was moderately higher than the DDS in all age groups. Moreover, a DDS approach may even be more realistic, as cooked foodstuffs are used for dietary exposure assessment. The study confirms that the current levels of (210)Po do not pose a significant radiological risk to the local inhabitants.

Enhanced photo-stability and photocatalytic activity of Ag3PO4 via modification with BiPO4 and polypyrrole

NASA Astrophysics Data System (ADS)

Cai, Li; Jiang, Hui; Wang, Luxi

2017-10-01

Ag3PO4 photocatalysts modified with BiPO4 and polypyrrole (PPy) were successfully synthesized via a combination of co-precipitation hydrothermal technique and oxidative polymerization method. Their morphologies, structures and optical and electronic properties were characterized by means of scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscope (TEM), Brunauer-Emmett-Teller (BET) surface areas, X-ray diffraction (XRD), fourier transform infrared spectra (FT-IR), X-ray photo-electron spectroscopy (XPS), UV-vis diffuse reflection spectra (UV-vis DRS), photocurrent technique and electrochemical impedance spectra (EIS). The typical triphenylmethane dye (malachite green) was chosen as a target organic contaminants to estimate the photocatalytic activities and photo-stabilities of Ag3PO4-BiPO4-PPy heterostructures under visible light irradiation. The results indicated that the existence of BiPO4 and PPy not only showed great influences on the photocatalytic activity, but also significantly enhanced photo-stability of Ag3PO4 in repeated and long-term applications. The degradation conversion of Ag3PO4-BiPO4-PPy heterostructures (ABP-3) was 1.58 times of that of pure Ag3PO4. The photo-corrosion phenomenon of Ag3PO4 was effectively avoided. The photocatalytic activity of up to 87% in the Ag3PO4-BiPO4-PPy heterostructures (ABP-3) can be remained after five repeated cycles, while only about 33% of the degradation efficiency can be reserved in pure Ag3PO4. The possible mechanism of enhanced photo-stability and photocatalytic activity of Ag3PO4-BiPO4-PPy heterostructures was also discussed in this work.

Adding part-of-speech information to the SUBTLEX-US word frequencies.

PubMed

Brysbaert, Marc; New, Boris; Keuleers, Emmanuel

2012-12-01

The SUBTLEX-US corpus has been parsed with the CLAWS tagger, so that researchers have information about the possible word classes (parts-of-speech, or PoSs) of the entries. Five new columns have been added to the SUBTLEX-US word frequency list: the dominant (most frequent) PoS for the entry, the frequency of the dominant PoS, the frequency of the dominant PoS relative to the entry's total frequency, all PoSs observed for the entry, and the respective frequencies of these PoSs. Because the current definition of lemma frequency does not seem to provide word recognition researchers with useful information (as illustrated by a comparison of the lemma frequencies and the word form frequencies from the Corpus of Contemporary American English), we have not provided a column with this variable. Instead, we hope that the full list of PoS frequencies will help researchers to collectively determine which combination of frequencies is the most informative.

Collisional excitation of interstellar PO(X2Π) by He: new ab initio potential energy surfaces and scattering calculations

NASA Astrophysics Data System (ADS)

Lique, François; Jiménez-Serra, Izaskun; Viti, Serena; Marinakis, Sarantos

2018-01-01

We present the first ab initio potential energy surfaces (PESs) for the PO(X2Π)-He van der Waals system. The PESs were obtained using the open-shell partially spin-restricted coupled cluster approach with single, double and perturbative triple excitations [UCCSD(T)]. The augmented correlation-consistent polarized valence triple-zeta (aug-cc-pVTZ) basis set was employed supplemented by mid-bond functions. Integral and differential cross sections for the rotational excitation in PO-He collisions were calculated using the new PES and compared with results in similar systems. Finally, our work presents the first hyperfine-resolved cross sections for this system that are needed for accurate modelling in astrophysical environments.

Facile solution-precipitation assisted synthesis and luminescence property of greenish-yellow emitting Ca{sub 6}Ba(PO{sub 4}){sub 4}O:Eu{sup 2+} phosphor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ji, Haipeng; Huang, Zhaohui, E-mail: huang118@cugb.edu.cn; Xia, Zhiguo, E-mail: xiazg@ustb.edu.cn

2016-03-15

Highlights: • Ca{sub 6}Ba(PO{sub 4}){sub 4}O:Eu{sup 2+} phosphor was prepared by the solution-precipitation assisted route. • The phosphors have satisfactory smooth grain surface and particle size. • It shows greenish-yellow color emission (maximum at 540 nm) upon blue light excitation. • Eu{sup 2+} is coordinated with isolated oxygen atoms and those from PO{sub 4} polyhedra. - Abstract: Greenish-yellow emitting microcrystalline Ca{sub 6}Ba(PO{sub 4}){sub 4}O:Eu{sup 2+} phosphor was successfully prepared by a solution-precipitation assisted high temperature reaction method. Phase structure, morphology and/or luminescence properties of the precursor and the as-prepared phosphors were characterized. The phase-pure Ca{sub 6}Ba(PO{sub 4}){sub 4}O:Eu{sup 2+} phosphorsmore » were obtained with smooth grain surface and particle size of 2–8 μm. Ca{sub 6}Ba(PO{sub 4}){sub 4}O:Eu{sup 2+} exhibits bright greenish-yellow color emission with its maximum at 540 nm upon UV-blue light excitation. The maximum position of the broad emission band is independent on the calcination temperature. The emission intensity increases with increasing calcination temperature due to improved crystallinity. Besides, the presence of two Eu{sup 2+} emission centers in the Ca{sub 6}Ba(PO{sub 4}){sub 4}O crystal lattice was confirmed and the coordination effects are considered concerning the roles of isolated O atoms and those from the PO{sub 4} tetrahedra.« less

A study of amplifying the response of an LR115 solid state track detector by combining it with electret.

PubMed

Nikezić, D; Krstić, D

1995-12-01

Radon progeny are positively charged immediately after formation. A negatively charged electret collects radon progeny atoms which are produced in the diffusion chamber. The detector sensitivity may be increased by using an electret in front of solid state nuclear track detector. Dependence of detection sensitivity on distance between electret and detector LR115 II is studied theoretically and experimentally in this paper. A relatively small fraction of 218Po atoms that formed in the diffusion chamber are collected by the electret. We estimated that the attracted fraction of 218Po was 17% while the attracted fraction of 214Bi-214Po is considerably larger and amounted to approximately 60%. These results confirm previous finding that 218Po atoms discharge quickly after their formation. The comparative radon measurements using diffusion chambers with and without electrets were performed. The amplification of detector sensitivity due to the electret amounted to approximately 80%.

Structure of C3PO and Mechanism of Human RISC Activation

PubMed Central

Ye, Xuecheng; Huang, Nian; Liu, Ying; Paroo, Zain; Huerta, Carlos; Li, Peng; Chen, She; Liu, Qinghua; Zhang, Hong

2011-01-01

Assembly of the RNA-induced silencing complex (RISC) consists of loading duplex (guide/passenger) siRNA onto and removing the passenger strand from Argonaute (Ago2). Ago2 contributes critically to RISC activation by nicking the passenger strand. Here, we reconstituted duplex siRNA-initiated RISC activity using recombinant human (h)Ago2 and C3PO, indicating a critical role for C3PO in hAgo2-RISC activation. Consistently, genetic depletion of C3PO compromised RNA silencing in mammalian cells. We determined the crystal structure of hC3PO, which reveals an asymmetric octamer barrel consisting of six Translin and two TRAX subunits. This asymmetric assembly is critical for the function of C3PO as a novel endonuclease that cleaves RNA at the interior surface. The current work supports a Dicer-independent mechanism for human RISC activation: 1) Ago2 directly binds duplex siRNA and nicks the passenger strand; 2) C3PO activates RISC by degrading Ago2-nicked passenger strand. PMID:21552258

Unlocking the energy capabilities of micron-sized LiFePO4.

PubMed

Guo, Limin; Zhang, Yelong; Wang, Jiawei; Ma, Lipo; Ma, Shunchao; Zhang, Yantao; Wang, Erkang; Bi, Yujing; Wang, Deyu; McKee, William C; Xu, Ye; Chen, Jitao; Zhang, Qinghua; Nan, Cewen; Gu, Lin; Bruce, Peter G; Peng, Zhangquan

2015-08-03

Utilization of LiFePO4 as a cathode material for Li-ion batteries often requires size nanonization coupled with calcination-based carbon coating to improve its electrochemical performance, which, however, is usually at the expense of tap density and may be environmentally problematic. Here we report the utilization of micron-sized LiFePO4, which has a higher tap density than its nano-sized siblings, by forming a conducting polymer coating on its surface with a greener diazonium chemistry. Specifically, micron-sized LiFePO4 particles have been uniformly coated with a thin polyphenylene film via the spontaneous reaction between LiFePO4 and an aromatic diazonium salt of benzenediazonium tetrafluoroborate. The coated micron-sized LiFePO4, compared with its pristine counterpart, has shown improved electrical conductivity, high rate capability and excellent cyclability when used as a 'carbon additive free' cathode material for rechargeable Li-ion batteries. The bonding mechanism of polyphenylene to LiFePO4/FePO4 has been understood with density functional theory calculations.

Unlocking the energy capabilities of micron-sized LiFePO4

PubMed Central

Guo, Limin; Zhang, Yelong; Wang, Jiawei; Ma, Lipo; Ma, Shunchao; Zhang, Yantao; Wang, Erkang; Bi, Yujing; Wang, Deyu; McKee, William C.; Xu, Ye; Chen, Jitao; Zhang, Qinghua; Nan, Cewen; Gu, Lin; Bruce, Peter G.; Peng, Zhangquan

2015-01-01

Utilization of LiFePO4 as a cathode material for Li-ion batteries often requires size nanonization coupled with calcination-based carbon coating to improve its electrochemical performance, which, however, is usually at the expense of tap density and may be environmentally problematic. Here we report the utilization of micron-sized LiFePO4, which has a higher tap density than its nano-sized siblings, by forming a conducting polymer coating on its surface with a greener diazonium chemistry. Specifically, micron-sized LiFePO4 particles have been uniformly coated with a thin polyphenylene film via the spontaneous reaction between LiFePO4 and an aromatic diazonium salt of benzenediazonium tetrafluoroborate. The coated micron-sized LiFePO4, compared with its pristine counterpart, has shown improved electrical conductivity, high rate capability and excellent cyclability when used as a ‘carbon additive free' cathode material for rechargeable Li-ion batteries. The bonding mechanism of polyphenylene to LiFePO4/FePO4 has been understood with density functional theory calculations. PMID:26235395

Using the nutrient ratio NO/PO as a tracer of continental shelf waters in the central Arctic Ocean

NASA Astrophysics Data System (ADS)

Wilson, Cara; Wallace, Douglas W. R.

1990-12-01

Historical nitrate, phosphate, and dissolved oxygen data from the central Arctic Ocean are examined with particular emphasis on the conservative parameters NO (9 * NO3 + O2) and PO (135 * PO4 + O2). The NO/PO ratio is shown to increase with depth in the Canada Basin, being ˜0.78 in Surface and Upper Halocline Waters and ˜1.0 in the Atlantic Layer and Deep Waters. Lower Halocline Water is marked by NO and PO minima and intermediate NO/PO. NO/PO ratios from the Arctic shelf seas are examined to determine possible source regions for the various water masses. The NO/PO ratio of Canada Basin Deep Water implies an upper bound of ˜11% shelf water contribution to this water mass. A slight oxygen maximum core in the Lower Halocline Water is identified at a salinity of S = 34.5 in the vicinity of the Alpha Ridge. This core appears to be diminished by diapycnal mixing and does not extend into the Beaufort Gyre.

Unlocking the energy capabilities of micron-sized LiFePO4

NASA Astrophysics Data System (ADS)

Guo, Limin; Zhang, Yelong; Wang, Jiawei; Ma, Lipo; Ma, Shunchao; Zhang, Yantao; Wang, Erkang; Bi, Yujing; Wang, Deyu; McKee, William C.; Xu, Ye; Chen, Jitao; Zhang, Qinghua; Nan, Cewen; Gu, Lin; Bruce, Peter G.; Peng, Zhangquan

2015-08-01

Utilization of LiFePO4 as a cathode material for Li-ion batteries often requires size nanonization coupled with calcination-based carbon coating to improve its electrochemical performance, which, however, is usually at the expense of tap density and may be environmentally problematic. Here we report the utilization of micron-sized LiFePO4, which has a higher tap density than its nano-sized siblings, by forming a conducting polymer coating on its surface with a greener diazonium chemistry. Specifically, micron-sized LiFePO4 particles have been uniformly coated with a thin polyphenylene film via the spontaneous reaction between LiFePO4 and an aromatic diazonium salt of benzenediazonium tetrafluoroborate. The coated micron-sized LiFePO4, compared with its pristine counterpart, has shown improved electrical conductivity, high rate capability and excellent cyclability when used as a `carbon additive free' cathode material for rechargeable Li-ion batteries. The bonding mechanism of polyphenylene to LiFePO4/FePO4 has been understood with density functional theory calculations.

Removal of {sup 222}Rn daughters from metal surfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zuzel, G.; Wojcik, M.; Majorovits, B.

Removal of the long-lived {sup 222}Rn daughters ({sup 210}Pb, {sup 210}Bi and {sup 210}Po) from copper, stainless steel and germanium surfaces was investigated. As cleaning techniques etching and electro-polishing was applied to samples in a form of discs exposed earlier to a strong radon source. Reduction of the {sup 210}Pb activity was tested using a HPGe spectrometer, for {sup 210}Bi a beta spectrometer and for {sup 210}Po an alpha spectrometer was used. According to the conducted measurements electro-polishing was always more efficient compared to etching and in case of copper the activity reduction factors for {sup 210}Pb, {sup 210}Bi andmore » {sup 210}Po were between 200 and 400. Etching does not remove {sup 210}Po from copper but works very efficiently from germanium. Results obtained for {sup 210}Pb and {sup 210}Bi for etched stainless steel were worse but still slightly better than those achieved for copper.« less

Native defects in silver orthophosphate and their effects on photocatalytic activity under visible light irradiation

NASA Astrophysics Data System (ADS)

Sulaeman, Uyi; Hermawan, Dadan; Andreas, Roy; Abdullah, Ahmad Zuhairi; Yin, Shu

2018-01-01

Native defects in silver orthophosphate could be generated by simple co-precipitation method under ethanol-aqueous solution using AgNO3 and Na2HPO4.12H2O. AgNO3 ethanol-aqueous solution with the ethanol contents of 0%, 25%, 50%, 75%, 90% and 100% was reacted with Na2HPO4 aqueous solution. The produced catalysts were characterized using XRD, DRS, FE-SEM, BET specific surface area and XPS. The increase of ethanol content in the synthesis process decreased the Ag/P atomic ratio of Ag3PO4. The native defects of silver vacancy might be generated on the surface of Ag3PO4. The activity of Ag3PO4 for Rhodamine B degradation dramatically increased by 5.8 times higher compared to that of the pristine Ag3PO4. The defect states of Ag vacancies enhanced the separation of electron-hole pairs, leading to the improvement of photocatalytic activity.

Ferrous Iron Oxidation under Varying pO2 Levels: The Effect of Fe(III)/Al(III) Oxide Minerals and Organic Matter.

PubMed

Chen, Chunmei; Thompson, Aaron

2018-01-16

Abiotic Fe(II) oxidation by O 2 commonly occurs in the presence of mineral sorbents and organic matter (OM) in soils and sediments; however, this tertiary system has rarely been studied. Therefore, we examined the impacts of mineral surfaces (goethite and γ-Al 2 O 3 ) and organic matter [Suwannee River fulvic acid (SRFA)] on Fe(II) oxidation rates and the resulting Fe(III) (oxyhydr)oxides under 21 and 1% pO 2 at pH 6. We tracked Fe dynamics by adding 57 Fe(II) to 56 Fe-labeled goethite and γ-Al 2 O 3 and characterized the resulting solids using 57 Fe Mössbauer spectroscopy. We found Fe(II) oxidation was slower at low pO 2 and resulted in higher-crystallinity Fe(III) phases. Relative to oxidation of Fe(II) (aq) alone, both goethite and γ-Al 2 O 3 surfaces increased Fe(II) oxidation rates regardless of pO 2 levels, with goethite being the stronger catalyst. Goethite surfaces promoted the formation of crystalline goethite, while γ-Al 2 O 3 favored nano/small particle or disordered goethite and some lepidocrocite; oxidation of Fe(II) aq alone favored lepidocrocite. SRFA reduced oxidation rates in all treatments except the mineral-free systems at 21% pO 2 , and SRFA decreased Fe(III) phase crystallinity, facilitating low-crystalline ferrihydrite in the absence of mineral sorbents, low-crystalline lepidocrocite in the presence of γ-Al 2 O 3 , but either crystalline goethite or ferrihydrite when goethite was present. This work highlights that the oxidation rate, the types of mineral surfaces, and OM control Fe(III) precipitate composition.

Effects of silane- and MDP-based primers application orders on zirconia-resin adhesion-A ToF-SIMS study.

PubMed

Chuang, Shu-Fen; Kang, Li-Li; Liu, Yi-Chuan; Lin, Jui-Che; Wang, Ching-Cheng; Chen, Hui-Min; Tai, Cheng-Kun

2017-08-01

To evaluate the 3-methacryloyloxypropyltrimethoxysilane (MPS)- and 10-methacryloyloxydecyl-dihydrogen-phosphate (MDP)-base primers, in their single or sequential applications, with regard to modifying zirconia surfaces and improving resin-zirconia adhesion. Zirconia disks received different treatments: without primer (Zr), MPS-base primer (S), MDP-base primer (M), MPS/MDP mixture (SMmix), MPS followed by MDP (SM), and MDP followed by MPS (MS). The compositions and chemical interactions of the coatings to zirconia were analyzed using time-of-flight secondary ion mass spectrometry (ToF-SIMS) and reconstructed 3D ion images. Surface wettability of these coatings to water and resin adhesive was assessed. The shear bond strength (SBS) between resin and the treated zirconia was also examined before and after thermocycling. Groups S and MS presented substantial OH - ions in the coatings and zirconia substrate. PO 2 - and PO 3 - fragments existed in all MDP-treatment groups with various proportions and distributions, while groups M and SM showed higher proportions of PO 3 - and the zirconium phosphate related ions. In 3D ion images, PO 3 - in groups M and SM was denser and segregated to the interface, but was dispersed or overlaid above PO 2 - in SMmix and MS. All the primers increased the surface wettability to water and resin, with M and SM presenting superhydrophilic surfaces. All MDP-treatment groups showed improved SBS before thermocycling, while M and SM retained higher SBS after this. The MDP-base primer shows a relevant function in facilitating POZr bonding and enhancing resin-zirconia bonding. The co-treated MPS impairs the chemical activity of MDP, especially if it is the final coat. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

A hydrothermally synthesized LiFePO4/C composite with superior low-temperature performance and cycle life

NASA Astrophysics Data System (ADS)

Wu, Guan; Liu, Na; Gao, Xuguang; Tian, Xiaohui; Zhu, Yanbin; Zhou, Yingke; Zhu, Qingyou

2018-03-01

The LiFePO4/C composites have been successfully synthesized by a hydrothermal process, with the combined carbon sources of fructose and calcium lignosulfonate. The morphology and microstructure of LiFePO4/C were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and Fourier transform infrared spectroscopy. The electrochemical properties were evaluated by the constant-current charge/discharge tests, cyclic voltammetry and electrochemical impedance spectroscopy. The uniform carbon coating layer derived from calcium lignosulfonate can effectively improve the electronic conductivity, lithium-ion diffusivity and surface stability of the LiFePO4/C composites and prevent the side reactions between the LiFePO4 particles and electrolytes. The LiFePO4/C composites display excellent rate capability, superior cycle life and outstanding low temperature performance, which are promising for lithium-ion battery applications in electrical vehicles and electrical energy storage systems.

Nanotechnology Enabled Hybrid Power System Suitable for Portable Telecommunications and Sensor Applications

DTIC Science & Technology

2010-12-01

and conventional Li-ion cells is the cathode material. Lithium iron phosphate ( LiFePO4 ) is a cathode material with many desirable characteristics: low... LiFePO4 , coated with conductive materials. The high surface area of the nanoparticles allows excellent interpenetration of the conductive materials...above--the A123 LiFePO4 -based nanoenabled battery, the Ioxus nanoenabled supercapacitor, and our custom-designed control circuit--were assembled into a

Films based on protein isolated from croaker (Micropogonias furnieri) and palm oil.

PubMed

Halal, Shanise Lisie Mello El; Zavareze, Elessandra da Rosa; Rocha, Meritaine da; Pinto, Vânia Zanella; Nunes, Michael Ramos; Luvielmo, Márcia de Mello; Prentice, Carlos

2016-05-01

The microstructure and the physical, mechanical, barrier and thermal properties of films based on different concentrations of protein isolated from croaker waste (CPI) and palm oil (PO) were analyzed. Films were elaborated by a casting technique using 2, 3 and 4 g CPI 100 g(-1) of a filmogenic solution and 0, 10 and 20 g of PO 100 g(-1) CPI. Microstructure of the film surfaces of CPI with PO showed no presence of lipid droplets dispersed in the filmogenic matrix, although a rough surface was present. Films with 3% and 4% CPI and 20% PO had the lowest rates of water vapor permeability. When there was an addition of PO to the reduced tensile strength of the films, regardless of the concentration of CPI, this addition reduced the elongation of films with 3% and 4% CPI; however, it did not influence films with 2% CPI, which did not differ from the control film (0% OP). Thermal analysis revealed that films with the highest PO percentage had a lower initial weight loss when compared with other films, due to higher hydrophobicity. The use of protein isolate obtained from fish residues of low commercial value and palm oil is viable for the production of biodegradable films because the latter constitute good barrier properties and thermal stability. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Frequency-independent approach to calculate physical optics radiations with the quadratic concave phase variations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Yu Mao, E-mail: yumaowu@fudan.edu.cn; Teng, Si Jia, E-mail: sjteng12@fudan.edu.cn

In this work, we develop the numerical steepest descent path (NSDP) method to calculate the physical optics (PO) radiations with the quadratic concave phase variations. With the surface integral equation method, the physical optics (PO) scattered fields are formulated and further reduced to the surface integrals. The high frequency physical critical points contributions, including the stationary phase points, the boundary resonance points and the vertex points are comprehensively studied via the proposed NSDP method. The key contributions of this work are twofold. One is that together with the PO integrals taking the quadratic parabolic and hyperbolic phase terms, this workmore » makes the NSDP theory be complete for treating the PO integrals with quadratic phase variations. Another is that, in order to illustrate the transition effect of the high frequency physical critical points, in this work, we consider and further extend the NSDP method to calculate the PO integrals with the coalescence of the high frequency critical points. Numerical results for the highly oscillatory PO integral with the coalescence of the critical points are given to verify the efficiency of the proposed NSDP method. The NSDP method could achieve the frequency independent computational workload and error controllable accuracy in all the numerical experiments, especially for the case of the coalescence of the high frequency critical points.« less

Silica-modified luminescent LaPO4 :Eu@LaPO4 @SiO2 core/shell nanorods: Synthesis, structural and luminescent properties.

PubMed

Ansari, Anees A

2018-02-01

Monoclinic-type tetragonal LaPO 4 :Eu (core) and LaPO 4 :Eu@LaPO 4 (core/shell) nanorods (NRs) were successfully prepared using a urea-based co-precipitation process under ambient conditions. An amorphous silica layer was coated around the luminescent core/shell NRs via the sol-gel process to improve their solubility and colloidal stability in aqueous and non-aqueous media. The prepared nano-products were systematically characterized by X-ray diffraction pattern, transmission electron microscopy, energy dispersive X-ray analysis, and FTIR, UV/Vis, and photoluminescence spectroscopy to examine their phase purity, crystal phase, surface chemistry, solubility and luminescence characteristics. The length and diameter of the nano-products were in the range 80-120 nm and 10-15 nm, respectively. High solubility of the silica-modified core/shell/Si NRs was found for the aqueous medium. The luminescent core NRs exhibited characteristic excitation and emission transitions in the visible region that were greatly affected by surface growth of insulating LaPO 4 and silica layers due to the multiphonon relaxation rate. Our luminescence spectral results clearly show a distinct difference in intensities for core, core/shell, and core/shell/Si NRs. Highly luminescent NRs with good solubility could be useful candidates for a variety of photonic-based biomedical applications. Copyright © 2017 John Wiley & Sons, Ltd.

Diazotrophic bacterioplankton in a coral reef lagoon: phylogeny, diel nitrogenase expression and response to phosphate enrichment.

PubMed

Hewson, Ian; Moisander, Pia H; Morrison, Amanda E; Zehr, Jonathan P

2007-05-01

We investigated diazotrophic bacterioplankton assemblage composition in the Heron Reef lagoon (Great Barrier Reef, Australia) using culture-independent techniques targeting the nifH fragment of the nitrogenase gene. Seawater was collected at 3 h intervals over a period of 72 h (i.e. over diel as well as tidal cycles). An incubation experiment was also conducted to assess the impact of phosphate (PO(4)3*) availability on nifH expression patterns. DNA-based nifH libraries contained primarily sequences that were most similar to nifH from sediment, microbial mat and surface-associated microorganisms, with a few sequences that clustered with typical open ocean phylotypes. In contrast to genomic DNA sequences, libraries prepared from gene transcripts (mRNA amplified by reverse transcription-polymerase chain reaction) were entirely cyanobacterial and contained phylotypes similar to those observed in open ocean plankton. The abundance of Trichodesmium and two uncultured cyanobacterial phylotypes from previous studies (group A and group B) were studied by quantitative-polymerase chain reaction in the lagoon samples. These were detected as transcripts, but were not detected in genomic DNA. The gene transcript abundance of these phylotypes demonstrated variability over several diel cycles. The PO(4)3* enrichment experiment had a clearer pattern of gene expression over diel cycles than the lagoon sampling, however PO(4)3* additions did not result in enhanced transcript abundance relative to control incubations. The results suggest that a number of diazotrophs in bacterioplankton of the reef lagoon may originate from sediment, coral or beachrock surfaces, sloughing into plankton with the flooding tide. The presence of typical open ocean phylotype transcripts in lagoon bacterioplankton may indicate that they are an important component of the N cycle of the coral reef.

NCO-sP(EO-stat-PO) coatings on gold sensors--a QCM study of hemocompatibility.

PubMed

Sinn, Stefan; Eichler, Mirjam; Müller, Lothar; Bünger, Daniel; Groll, Jürgen; Ziemer, Gerhard; Rupp, Frank; Northoff, Hinnak; Geis-Gerstorfer, Jürgen; Gehring, Frank K; Wendel, Hans P

2011-01-01

The reliability of implantable blood sensors is often hampered by unspecific adsorption of plasma proteins and blood cells. This not only leads to a loss of sensor signal over time, but can also result in undesired host vs. graft reactions. Within this study we evaluated the hemocompatibility of isocyanate conjugated star shaped polytheylene oxide-polypropylene oxide co-polymers NCO-sP(EO-stat-PO) when applied to gold surfaces as an auspicious coating material for gold sputtered blood contacting sensors. Quartz crystal microbalance (QCM) sensors were coated with ultrathin NCO-sP(EO-stat-PO) films and compared with uncoated gold sensors. Protein resistance was assessed by QCM measurements with fibrinogen solution and platelet poor plasma (PPP), followed by quantification of fibrinogen adsorption. Hemocompatibility was tested by incubation with human platelet rich plasma (PRP). Thrombin antithrombin-III complex (TAT), β-thromboglobulin (β-TG) and platelet factor 4 (PF4) were used as coagulation activation markers. Furthermore, scanning electron microscopy (SEM) was used to visualize platelet adhesion to the sensor surfaces. Compared to uncoated gold sensors, NCO-sP(EO-stat-PO) coated sensors revealed significant better resistance against protein adsorption, lower TAT generation and a lower amount of adherent platelets. Moreover, coating with ultrathin NCO-sP(EO-stat-PO) films creates a cell resistant hemocompatible surface on gold that increases the chance of prolonged sensor functionality and can easily be modified with specific receptor molecules.

NCO-sP(EO-stat-PO) Coatings on Gold Sensors—a QCM Study of Hemocompatibility

PubMed Central

Sinn, Stefan; Eichler, Mirjam; Müller, Lothar; Bünger, Daniel; Groll, Jürgen; Ziemer, Gerhard; Rupp, Frank; Northoff, Hinnak; Geis-Gerstorfer, Jürgen; Gehring, Frank K.; Wendel, Hans P.

2011-01-01

The reliability of implantable blood sensors is often hampered by unspecific adsorption of plasma proteins and blood cells. This not only leads to a loss of sensor signal over time, but can also result in undesired host vs. graft reactions. Within this study we evaluated the hemocompatibility of isocyanate conjugated star shaped polytheylene oxide—polypropylene oxide co-polymers NCO-sP(EO-stat-PO) when applied to gold surfaces as an auspicious coating material for gold sputtered blood contacting sensors. Quartz crystal microbalance (QCM) sensors were coated with ultrathin NCO-sP(EO-stat-PO) films and compared with uncoated gold sensors. Protein resistance was assessed by QCM measurements with fibrinogen solution and platelet poor plasma (PPP), followed by quantification of fibrinogen adsorption. Hemocompatibility was tested by incubation with human platelet rich plasma (PRP). Thrombin antithrombin-III complex (TAT), β-thromboglobulin (β-TG) and platelet factor 4 (PF4) were used as coagulation activation markers. Furthermore, scanning electron microscopy (SEM) was used to visualize platelet adhesion to the sensor surfaces. Compared to uncoated gold sensors, NCO-sP(EO-stat-PO) coated sensors revealed significant better resistance against protein adsorption, lower TAT generation and a lower amount of adherent platelets. Moreover, coating with ultrathin NCO-sP(EO-stat-PO) films creates a cell resistant hemocompatible surface on gold that increases the chance of prolonged sensor functionality and can easily be modified with specific receptor molecules. PMID:22163899

Radioactivity of cigarettes and the importance of (210)Po and thorium isotopes for radiation dose assessment due to smoking.

PubMed

Kubalek, Davor; Serša, Gregor; Štrok, Marko; Benedik, Ljudmila; Jeran, Zvonka

2016-05-01

Tobacco and tobacco smoke are very complex mixtures. In addition to various chemical and organic compounds they also contain natural radioactive elements (radionuclides). In this work, the natural radionuclide activity concentrations ((234)U, (238)U, (228)Th, (230)Th, (232)Th, (226)Ra, (210)Pb and (210)Po) of nine different cigarette samples available on the Slovenian market are reported. In addition to (210)Po, the transfer of thorium isotopes from a cigarette to a smoker's body and lungs have been determined for the first time. Cigarette smoke and exhaled air from smokers' lungs were collected from volunteer smokers (C-4 brand) to determinate what quantity of (210)Po and thorium isotopes is transferred from the tobacco to the smoker's lungs. Cigarette ash and smoked filters were also collected and analysed. Among the determined isotopes, (210)Pb and (210)Po showed the highest activity concentrations. During the smoking of one cigarette approximately 22% of (210)Po (and presumably its predecessor (210)Pb), 0.6% of (228)Th, 24% of (230)Th, and 31% of (232)Th are transferred from the cigarette and retained in the smoker's body. The estimated annual effective dose for smokers is 61 μSv/year from (210)Po; 9 μSv/year from (210)Pb; 6 μSv/year from (228)Th; 47 μSv/year from (230)Th, and 37 μSv/year from (232)Th. These results show the importance of thorium isotopes in contributing to the annual effective dose for smoking. Copyright © 2016 Elsevier Ltd. All rights reserved.

A chemically activated graphene-encapsulated LiFePO4 composite for high-performance lithium ion batteries.

PubMed

Ha, Jeonghyun; Park, Seung-Keun; Yu, Seung-Ho; Jin, Aihua; Jang, Byungchul; Bong, Sungyool; Kim, In; Sung, Yung-Eun; Piao, Yuanzhe

2013-09-21

A composite of modified graphene and LiFePO4 has been developed to improve the speed of charging-discharging and the cycling stability of lithium ion batteries using LiFePO4 as a cathode material. Chemically activated graphene (CA-graphene) has been successfully synthesized via activation by KOH. The as-prepared CA-graphene was mixed with LiFePO4 to prepare the composite. Microscopic observation and nitrogen sorption analysis have revealed the surface morphologies of CA-graphene and the CA-graphene/LiFePO4 composite. Electrochemical properties have also been investigated after assembling coin cells with the CA-graphene/LiFePO4 composite as a cathode active material. Interestingly, the CA-graphene/LiFePO4 composite has exhibited better electrochemical properties than the conventional graphene/LiFePO4 composite as well as bare LiFePO4, including exceptional speed of charging-discharging and excellent cycle stability. That is because the CA-graphene in the composite provides abundant porous channels for the diffusion of lithium ions. Moreover, it acts as a conducting network for easy charge transfer and as a divider, preventing the aggregation of LiFePO4 particles. Owing to these properties of CA-graphene, LiFePO4 could demonstrate enhanced and stably long-lasting electrochemical performance.

Determination of Po-210 content in cigarette smoke using a smoking machine: A case study of Iranian cigarettes.

PubMed

Horváth, Mária; Shahrokhi, Amin; Bátor, Péter; Tóth-Bodrogi, Edit; Kovács, Tibor

2017-08-01

The Po-210 content of tobacco has been known for a long time, however, different results can be found about the estimated amount of Po-210 that is inhaled by humans as a result of smoking cigarettes. Because of the unique properties of Po-210, the smoking machines available on the market are not suitable because of their failure to quantitatively collect Po-210 for measurement. Therefore, to estimate precisely the amount of Po-210 entering the lungs as a result of smoking, a smoking machine and sampling protocol based on relevant ISO standards - ISO-3308, ISO-3402 and ISO-4387 - was developed. A 5% HCl solution was found to be the best absorber of Po-210 from smoke. Seventeen different brands of cigarettes distributed in Iran were used to validate the new machine and sampling protocol. The Po-210 concentration was determined by alpha spectrometry; the cigarette smoke solution underwent combined acid treatment after adding a Po-209 tracer. The Po-210 activity concentration of cigarettes sold in Iran was between 9.7 ± 1.2 and 26.5 ± 4.6 mBq/cigarette and it was determined that there was no relationship between the Po-210 and nicotine contents of cigarette smoke. Additionally, it was found that 15 ± 10% of the cigarette Po-210 was transferred to the mainstream smoke. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of the Polishing Procedures on Color Stability and Surface Roughness of Composite Resins

PubMed Central

Schmitt, Vera Lucia; Puppin-Rontani, Regina Maria; Naufel, Fabiana Scarparo; Nahsan, Flávia Pardo Salata; Alexandre Coelho Sinhoreti, Mário; Baseggio, Wagner

2011-01-01

Objectives. To evaluate the polishing procedures effect on color stability and surface roughness of composite resins. Methods. Specimens were distributed into 6 groups: G1: Filtek Supreme XT + PoGo; G2: Filtek Supreme XT + Sof-Lex; G3: Filtek Supreme XT + no polishing; G4: Amelogen + PoGo; G5: Amelogen + Sof-Lex.; G6: Amelogen + no polishing. Initial color values were evaluated using the CIELab scale. After polishing, surface roughness was evaluated and the specimens were stored in coffee solution at 37°C for 7 days. The final color measurement and roughness were determined. Results. Sof-Lex resulted in lower staining. Amelogen showed the highest roughness values than Filtek Supreme on baseline and final evaluations regardless of the polishing technique. Filtek Supreme polished with PoGo showed the lowest roughness values. All groups presented discoloration after storage in coffee solution, regardless of the polishing technique. Conclusion. Multiple-step polishing technique provided lower degree of discoloration for both composite resins. The final surface texture is material and technique dependent. PMID:21991483

Synthesis and characterization of CdS/BiPO{sub 4} heterojunction photocatalyst

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Daimei, E-mail: chendaimei@cugb.edu.cn; Kuang, Zheng; Zhu, Qian

2015-06-15

Highlights: • A CdS/BiPO{sub 4} heterojunction was prepared by the solvothermal method. • The CdS/BiPO{sub 4} composite has the higher photocatalytic activity than the individual ones. • The optimal mass ratio of CdS to BiPO{sub 4} was 0.5. • The heterojunction structure of CdS/BiPO{sub 4} induces an effective electron–hole separation. - Abstract: A series of CdS/BiPO{sub 4} heterojunction photocatalysts with the visible-light response were synthesized by the solvothermal method. The resulting products were characterized by X-ray diffraction, Transmission electron microscopy, X-ray photoelectron spectroscopy, and UV–vis diffuse reflection spectroscopy. CdS nanoparticles with the size at range of 5–7 nm were immobilizedmore » on the surface of BiPO{sub 4} nanorods. The CdS/BiPO{sub 4} composite exhibited much higher photodegradation rate of methylene blue under visible light irradation compared to the pure CdS and BiPO{sub 4}. The optimal mass ratio of CdS to BiPO{sub 4} was 0.5, the photodegradation rate of which is 2.1 times higher than that of CdS. The enhancement of photocatalytic activity is attributed to the heterojunction structure of CdS/BiPO{sub 4} composite which induced the effective electron–hole separation between CdS and BiPO{sub 4}.« less

Fabrication of spherical mitigation pit on KH2PO4 crystal by micro-milling and modeling of its induced light intensification.

PubMed

Cheng, Jian; Chen, Mingjun; Liao, Wei; Wang, Haijun; Xiao, Yong; Li, Mingquan

2013-07-15

Micro-machining is the most promising method for KH(2)PO(4) crystal to mitigate the surface damage growth in high power laser system. In this work, spherical mitigation pit is fabricated by micro-milling with an efficient machining procedure. The light intensification caused by rear surface features before and after mitigation is numerically modeled based on the finite-difference time-domain method. The results indicate that the occurrence of total internal reflections should be responsible for the largest light intensification inside the crystal. For spherical pits after mitigation, the light intensification can be greatly alleviated by preventing the occurrence of total internal reflections. The light intensification caused by spherical mitigation pit is strongly dependent on the width-depth ratio and it is suggested that the width-depth ratio of spherical mitigation pit must be devised to be larger than 5.0 to achieve the minimal light intensification for the mitigation of surface damage growth. Laser damage tests for KH(2)PO(4) crystal validate that the laser damage resistance of initially damaged surface can be retrieved to near the level of ideal surface by replacing initial damage site with predesigned mitigation pit.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duan, Yandong; Zhang, Bingkai; Zheng, Jiaxin

Abstract. Due to the enhanced kinetic properties, nanocrystallites have received much attention as potential electrode materials for energy storage. However, because of the large specific surface areas of nanocrystallites, they usually suffer from decreased energy density, reduced cycling stability and total electrode capacity. In this work, we report a size-dependent excess capacity beyond the theoretical value of 170 mAhg-1 in a special carbon coated LiFePO4 composite cathode material, which delivers capacities of 191.2 and 213.5 mAhg-1 with the mean particle sizes of 83 nm and 42 nm, respectively. Moreover, this LiFePO4 composite also shows excellent cycling stability and high ratemore » performance. Our further experimental tests and ab initio calculations reveal that the excess capacity comes from the charge passivation for which the C-O-Fe bonds would lead to charge redistribution on the surface of LiFePO4 and hence to enhance the bonding interaction between surface O atoms and Li-ions. The surface reconstruction for excess Li-ion storage makes full use of the large specific surface area for the nanocrystallites, which can maintain the fast Li-ion transport and enhance the capacity greatly that the nanocrystallites usually suffers.« less

75 FR 81965 - Proposed Information Collection; Comment Request; Census Barriers, Attitudes, and Motivators...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-29

... Publicity Office (C2PO) conducted a series of qualitative, quantitative, attitudinal, and behavioral research initiatives to serve as a foundation for the 2010 Census Integrated Communications Program. Research results informed and validated marketing decisions throughout the entire campaign. C2PO researched...

A Near-Surface Burst EMP Driver Package for Neutron-Induced Sources.

DTIC Science & Technology

1980-09-01

FAa’S FD-F C SAwSB s3.sc 6O TO 10 C BEGIN NODIFIED QUADRATIC INTERPOLATION FOR NINlINUff 100 CONT INUE ICBIC.1 IFlIC.GTeICOUNT) 10 TO 110 YENP aISC-Sl) lSD ...M.I.T. LINCOLN LABORATORY Ro&.D ASSOCIATED P.O. DOE 369 P.O. BOX 73 P.O. 101x 9695 KttN F. A. SHAW AM LEONA WUoNLIN ATMN S- CLAY ROGERS CLEAIEILD. Ur

Carbon-Coated Current Collectors for High-Power Li-Ion Secondary Batteries

DTIC Science & Technology

2012-08-29

deposition condition. Surface analysis indicates that this thin C layer does not contain interfacial Al-carbide layer. LiFePO4 electrode using this C...layer does not contain an interfacial Al-carbide layer. LiFePO4 electrode using this C-coated Al current collector exhibits higher capacity under 10 C...cathode. LiFePO4 (LFPO) was used as active materials for test, and this cathode material was purchased from Aleees company. The LFPO active layer

Carbon-Coated Current Collectors for High-Power Li-ion Secondary Batteries III

DTIC Science & Technology

2013-12-02

surface. Electron-performance for use modified Al foil as current collector of the cathode. LiFePO4 (LFPO) was used as active materials for test...kinds of current collectors were shown in Fig. 4. It shows the rate capacity of LiFePO4 (LFPO) get poorer when using PAT-Al as current collector, and...commercial LiFePO4 (Ale84) on different current collector Figure 4. Rate capacities of LFPO electrodes with different current collectors. 0 20

Submarine groundwater discharge to Tampa Bay: Nutrient fluxes and biogeochemistry of the coastal aquifer

USGS Publications Warehouse

Kroeger, Kevin D.; Swarzenski, Peter W.; Greenwood, Wm. Jason; Reich, Christopher

2007-01-01

To separately quantify the roles of fresh and saline submarine groundwater discharge (SGD), relative to that of rivers, in transporting nutrients to Tampa Bay, Florida, we used three approaches (Darcy's Law calculations, a watershed water budget, and a 222Rn mass-balance) to estimate rate of SGD from the Pinellas peninsula. Groundwater samples were collected in 69 locations in the coastal aquifer to examine biogeochemical conditions, nutrient concentrations and stoichiometry, and salinity structure. Salinity structure was also examined using stationary electrical resistivity measurements. The coastal aquifer along the Pinellas peninsula was chemically reducing in all locations sampled, and that condition influences nitrogen (N) form and mobility of N and PO43−. Concentrations of NH4+, PO43− and ratio of dissolved inorganic N (DIN) to PO43− were all related to measured oxidation/reduction potential (pε) of the groundwater. Ratio of DIN: PO43− was below Redfield ratio in both fresh and saline groundwater. Nitrogen occurred almost exclusively in reduced forms, NH4+ and dissolved organic nitrogen (DON), suggesting that anthropogenic N is exported from the watershed in those forms. In comparison to other SGD studies, rate of PO43− flux in the seepage zone (μM m− 2 d− 1) in Tampa Bay was higher than previous estimates, likely due to 1) high watershed population density, 2) chemically reducing conditions, and 3) high ion concentrations in fresh groundwater. Estimates of freshwater groundwater flux indicate that the ratio of groundwater discharge to stream flow is ∼ 20 to 50%, and that the magnitudes of both the total dissolved nitrogen and PO43− loads due to fresh SGD are ∼ 40 to 100% of loads carried by streams. Estimates of SGD based on radon inventories in near-shore waters were 2 to 5 times greater than the estimates of freshwater groundwater discharge, suggesting that brackish and saline SGD is also an important process in Tampa Bay and results in flux of regenerated N and P from sediment to surface water.

Annual dose of Taiwanese from the ingestion of 210Po in oysters.

PubMed

Lee, Hsiu-wei; Wang, Jeng-Jong

2013-03-01

Oysters around the coast of Taiwan were collected, dried, spiked with a (209)Po tracer for yield, digested with concentrated HNO(3) and H(2)O(2), and finally dissolved in 0.5 N HCl. The polonium was then spontaneously deposited onto a silver disc, and the activity of (210)Po was measured using an alpha spectrum analyzer equipped with a silicon barrier detector. Meanwhile, the internal effective dose of (210)Po coming from the intake of oysters by Taiwanese was evaluated. The results of the present study indicate that (210)Po average activity concentrations ranged from 23.4 ± 0.4 to 126 ± 94 Bq kg(-1) of fresh oysters. The oysters coming from Penghu island and Kinmen island regions contain higher concentrations of (210)Po in comparison with oysters from other regions of Taiwan. The value of (210)Po weighted average activity concentrations for all oyster samples studied is 25.9 Bq kg(-1). The annual effective dose of Taiwanese due to the ingestion of (210)Po in oysters was estimated to be 4.1 × 10(-2) mSv y(-1). Copyright © 2013. Published by Elsevier Ltd.

210Po and 210Pb variations in fish species from the Aegean Sea and the contribution of 210Po to the radiation dose.

PubMed

Çatal, Ebru Mat; Uğur, Aysun; Ozden, Banu; Filizok, Işik

2012-04-01

In recent years, there has been increasing interest in the significance of natural radionuclides, particularly (210)Po, in the marine environment. (210)Po, a naturally occurring alpha emitter, accumulates in marine organisms and reflects differences in their diets. In the literature, there is no data for (210)Po and (210)Pb activity concentrations for fish species on the Turkish coast of Aegean Sea. Therefore, in this study, multiple fish species were collected from six stations seasonally on the Turkish coast of Aegean Sea and were analyzed for their (210)Po and (210)Pb content. The (210)Po and (210)Pb concentrations in the fish samples were found to vary from undetectable levels to 499 ± 44 Bq kg(-1) dry weight (dw) and from 1.0 ± 0.3 Bq kg(-1) to 35 ± 4.0 Bq kg(-1) (dw), respectively. There were no significant differences in the activity concentrations of (210)Po and (210)Pb in fish samples between seasons (ANOVA, P>0.05). The highest dose contribution of (210)Po to humans was calculated to be 10,530 μSv year(-1). Copyright © 2012 Elsevier Ltd. All rights reserved.

Electrochemical performances of LiMnPO4 synthesized from non-stoichiometric Li/Mn ratio.

PubMed

Xiao, Jie; Chernova, Natasha A; Upreti, Shailesh; Chen, Xilin; Li, Zheng; Deng, Zhiqun; Choi, Daiwon; Xu, Wu; Nie, Zimin; Graff, Gordon L; Liu, Jun; Whittingham, M Stanley; Zhang, Ji-Guang

2011-10-28

In this paper, the influences of the lithium content in the starting materials on the final performances of as-prepared Li(x)MnPO(4) (x hereafter represents the starting Li content in the synthesis step which does not necessarily mean that Li(x)MnPO(4) is a single phase solid solution in this work.) are systematically investigated. It has been revealed that Mn(2)P(2)O(7) is the main impurity when Li < 1.0 while Li(3)PO(4) begins to form once x > 1.0. The interactions between Mn(2)P(2)O(7) or Li(3)PO(4) impurities and LiMnPO(4) are studied in terms of the structural, electrochemical, and magnetic properties. At a slow rate of C/50, the reversible capacity of both Li(0.5)MnPO(4) and Li(0.8)MnPO(4) increases with cycling. This indicates a gradual activation of more sites to accommodate a reversible diffusion of Li(+) ions that may be related to the interaction between Mn(2)P(2)O(7) and LiMnPO(4) nanoparticles. Among all of the different compositions, Li(1.1)MnPO(4) exhibits the most stable cycling ability probably because of the existence of a trace amount of Li(3)PO(4) impurity that functions as a solid-state electrolyte on the surface. The magnetic properties and X-ray absorption spectroscopy (XAS) of the MnPO(4)·H(2)O precursor, pure and carbon-coated Li(x)MnPO(4) are also investigated to identify the key steps involved in preparing a high-performance LiMnPO(4). This journal is © the Owner Societies 2011

Radioactivity in three species of eastern Mediterranean jellyfish.

PubMed

Mamish, S; Al-Masri, M S; Durgham, H

2015-11-01

Activity concentrations of (137)Cs, (40)K, (210)Po, (210)Pb, (234)U and (238)U were determined in umbrella and oral arms of three widely distributed jellyfish species; namely Rhopilema nomadica Galil, 1990, Aurelia aurita Linne, 1758 and Aequorea forskalea Péron & Lesueur, 1810 collected from February 2011 to January 2012 in four sampling locations along the Syrian coast (Eastern Mediterranean Sea). The results have shown significant variations in radionuclides activity concentrations amongst the species. The average activity concentrations of (40)K, (210)Po, (210)Pb, (234)U and (238)U in the umbrella of R. nomadica species were higher than the average activity concentrations in the umbrella of A. aurita species by about 3.2, 1.4, 1.8, 3.2 and 3.2 folds, and A. forskalea species by about 45.5, 15.4, 19, 7.4 and 7.6 folds, respectively. The average activity concentrations of (40)K, (210)Po, (210)Pb, (234)U and (238)U in oral arms of R. nomadica species were higher than the average activity concentrations in oral arms of A. aurita species by about 3.8, 1.7, 1.9, 2.8 and 2.9 folds, respectively. (137)Cs activity concentrations were below the detection limit in all measured samples. In addition, activity concentrations of (137)Cs, (40)K, (210)Po, (210)Pb, (234)U and (238)U were also determined in 44 surface seawater samples and the activity concentrations ranged between 10.6 and 11.9 Bq l(-1) for (40)K, 1.1 and 1.4 mBq l(-1) for (210)Po, 0.5 and 0.7 mBq l(-1) for (210)Pb, 40.8 and 44.5 mBq l(-1) for (234)U, and 36.9 and 38.4 mBq l(-1) for (238)U, while (137)Cs activity concentrations were below the detection limit in all measured samples. Moreover, the umbrella and oral arms readily accumulated (40)K, (210)Po, (210)Pb, (234)U and (238)U above ambient seawater levels in the sequence of (210)Po > (210)Pb > (4) K > (234)U and (238)U. Concentration ratio (CR) values were relatively high for (210)Po and (210)Pb and reached 10(3) and 10(2), respectively for the jellyfish R. nomadica species compared to A. aurita and A. forskalea species. Therefore, R. nomadica can be used as biomonitor for these two radionuclides in the Eastern Mediterranean Sea. However, the obtained data can be considered the first reported baseline values for radioactivity in jellyfish. Copyright © 2015 Elsevier Ltd. All rights reserved.

Facile One-Step Sonochemical Synthesis and Photocatalytic Properties of Graphene/Ag3PO4 Quantum Dots Composites

NASA Astrophysics Data System (ADS)

Reheman, Abulajiang; Tursun, Yalkunjan; Dilinuer, Talifu; Halidan, Maimaiti; Kadeer, Kuerbangnisha; Abulizi, Abulikemu

2018-03-01

In this study, a novel graphene/Ag3PO4 quantum dot (rGO/Ag3PO4 QD) composite was successfully synthesized via a facile one-step photo-ultrasonic-assisted reduction method for the first time. The composites were analyzed by various techniques. According to the obtained results, Ag3PO4 QDs with a size of 1-4 nm were uniformly dispersed on rGO nanosheets to form rGO/Ag3PO4 QD composites. The photocatalytic activity of rGO/Ag3PO4 QD composites was evaluated by the decomposition of methylene blue (MB). Meanwhile, effects of the surfactant dosage and the amount of rGO on the photocatalytic activity were also investigated. It was found that rGO/Ag3PO4 QDs (WrGO:Wcomposite = 2.3%) composite exhibited better photocatalytic activity and stability with degrading 97.5% of MB within 5 min. The improved photocatalytic activities and stabilities were majorly related to the synergistic effect between Ag3PO4 QDs and rGO with high specific surface area, which gave rise to efficient interfacial transfer of photogenerated electrons and holes on both materials. Moreover, possible formation and photocatalytic mechanisms of rGO/Ag3PO4 QDs were proposed. The obtained rGO/Ag3PO4 QDs photocatalysts would have great potentials in sewage treatment and water splitting.

Graphene-like boron nitride modified bismuth phosphate materials for boosting photocatalytic degradation of enrofloxacin.

PubMed

Chen, Zhigang; Chen, Xiaoliu; Di, Jun; Liu, Yiling; Yin, Sheng; Xia, Jiexiang; Li, Huaming

2017-04-15

A novel graphene-like BN modified BiPO 4 material was prepared for the first time via a simple solvothermal process with the assistance of reactable ionic liquid 1-decyl-3-methylimidazolium dihydrogen phosphate ([Omim]H 2 PO 4 ). The as-prepared photocatalyst was characterized by XRD, FT-IR, Raman, XPS, TEM, DRS, BET, PL, EIS and ESR to investigate the structure, morphology, optical property, surface area, electrical property and active species. The photocatalytic activities of graphene-like BN/BiPO 4 materials were evaluated by the degradation of antibiotic enrofloxacin (ENR) under UV light irradiation and the 1wt% graphene-like BN/BiPO 4 displayed the best activity among the BN/BiPO 4 composites. The enhanced photocatalytic activity for the removal of enrofloxacin was attributed to higher separation efficiency of photogenerated electron-hole pairs, and the generated more O 2 - and OH radicals when the BN was modified on BiPO 4 . Moreover, a probable degradation mechanism was proposed for the improved photocatalytic activity of BN modified BiPO 4 . Copyright © 2016 Elsevier Inc. All rights reserved.

Uranium Adsorption on Ferrihydrite - Effects of Phosphate and Humic Acid

USGS Publications Warehouse

Payne, T.E.; Davis, J.A.; Waite, T.D.

1996-01-01

Uranium adsorption on ferrihydrite was studied as a function of pH in systems equilibrated with air, in the presence and absence of added phosphate and humic acid (HA). The objective was to determine the influence of PO43- and HA on uranium uptake. Below pH 7, the sorption of UO22+ typically increases with increasing pH (the 'low pH sorption edge'), with a sharp decrease in sorption above this pH value (the 'high pH edge'). The presence of ??PO43- of 10-4 mol/L moved the low pH edge to the left by approximately 0.8 pH units. The PO43- was strongly bound by the ferrihydrite surface, and the increased uptake of U was attributed to the formation of ternary surface complexes involving both UO22+ and PO43-. The addition of HA (9 mg/L) increased U uptake at pH values below 7, with little effect at higher pH values. The positions of the pH edges were also affected by the ionic strength and total U content. These experiments show that sorption interactions involving PO43 and HA must be considered in order to model the behavior of U in natural systems, in which these components are often present.

Effect upon biocompatibility and biocorrosion properties of plasma electrolytic oxidation in trisodium phosphate electrolytes.

PubMed

Kim, Yu-Kyoung; Park, Il-Song; Lee, Kwang-Bok; Bae, Tae-Sung; Jang, Yong-Seok; Oh, Young-Min; Lee, Min-Ho

2016-03-01

Surface modification to improve the corrosion resistance and biocompatibility of the Mg-Al-Zn-Ca alloy was conducted via plasma electrolytic oxidation (PEO) in an electrolyte that included phosphate. Calcium phosphate can be easily induced on the surface of a PEO coating that includes phosphate in a physiological environment because Ca(2+) ions in body fluids can be combined with PO4 (3-). Cytotoxicity of the PEO coating formed in electrolytes with various amounts of Na3PO4 was identified. In particular, the effects that PEO films have upon oxidative stress and differentiation of osteoblast activity were studied. As the concentration of Na3PO4 in the electrolyte increased, the oxide layer was found to become thicker, which increased corrosion resistance. However, the PEO coating formed in electrolytes with over 0.2 M of added Na3PO4 exhibited more microcracks and larger pores than those formed in smaller Na3PO4 concentrations owing to a large spark discharge. A nonuniform oxide film that included more phosphate caused more cytotoxicity and oxidative stress, and overabundant phosphate content in the oxide layer interrupted the differentiation of osteoblasts. The corrosion resistance of the magnesium alloy and the thickness of the oxide layer were increased by the addition of Na3PO4 in the electrolyte for PEO treatment. However, excessive phosphate content in the oxide layer led to oxidative stress, which resulted in reduced cell viability and activity.

Electrochemical and XPS study of LiFePO4 cathode nanocomposite with PPy/PEG conductive network

NASA Astrophysics Data System (ADS)

Fedorková, A.; Oriňáková, R.; Oriňák, A.; Kupková, M.; Wiemhöfer, H.-D.; Audinot, J. N.; Guillot, J.

2012-08-01

High performance PPy/PEG-LiFePO4 nanocomposites as cathode materials were synthesized by solvothermal method and simple chemical oxidative polymerization of pyrrole (Py) monomer on the surface of LiFePO4 particles. The samples were characterized by scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectrometry (XPS) and charge-discharge tests. PPyPEG hybrid layers decrease particle to particle contact resistance while the impedance measurements confirmed that the coating of PPy-PEG significantly decreases the charge transfer resistance of the electrode material. The initial discharge capacities of this sample at C/5 and 1C are 150 and 128 mAh/g, respectively. The results show that PPy/PEGLiFePO4 composites are more effective than bare LiFePO4 as cathode material.

Atomic-Scale Observations of (010) LiFePO4 Surfaces Before and After Chemical Delithiation.

PubMed

Kobayashi, Shunsuke; Fisher, Craig A J; Kato, Takeharu; Ukyo, Yoshio; Hirayama, Tsukasa; Ikuhara, Yuichi

2016-09-14

The ability to view directly the surface structures of battery materials with atomic resolution promises to dramatically improve our understanding of lithium (de)intercalation and related processes. Here we report the use of state-of-the-art scanning transmission electron microscopy techniques to probe the (010) surface of commercially important material LiFePO4 and compare the results with theoretical models. The surface structure is noticeably different depending on whether Li ions are present in the topmost surface layer or not. Li ions are also found to migrate back to surface regions from within the crystal relatively quickly after partial delithiation, demonstrating the facile nature of Li transport in the [010] direction. The results are consistent with phase transformation models involving metastable phase formation and relaxation, providing atomic-level insights into these fundamental processes.

EVALUATION OF MICROSOMAL AND CYTOSOLIC BIOMARKERS IN A SEVEN-DAY LARVAL TROUT SEIMENT TOXICITY TEST

EPA Science Inventory

Rainbow trout (Oncorhynclus mykiss) sac fry (larvae) were exposed to River Po sediments for 7 days. The sediments were collected in the River Po at two sites located upstream and downstream of the confluence of a polluted tributary, the River Lambro. An additional sediment treatm...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ye, Xuecheng; Huang, Nian; Liu, Ying

Assembly of the RNA-induced silencing complex (RISC) consists of loading duplex (guide-passenger) siRNA onto Argonaute (Ago2) and removing the passenger strand. Ago2 contributes critically to RISC activation by nicking the passenger strand. Here we reconstituted duplex siRNA-initiated RISC activity using recombinant human Ago2 (hAgo2) and C3PO, indicating that C3PO has a critical role in hAgo2-RISC activation. Consistently, genetic depletion of C3PO compromised RNA silencing in mammalian cells. We determined the crystal structure of hC3PO, which reveals an asymmetric octamer barrel consisting of six translin and two TRAX subunits. This asymmetric assembly is critical for the function of C3PO as anmore » endonuclease that cleaves RNA at the interior surface. The current work supports a Dicer-independent mechanism for human RISC activation, in which Ago2 directly binds duplex siRNA and nicks the passenger strand, and then C3PO activates RISC by degrading the Ago2-nicked passenger strand.« less

Conjugation of TbPO4·H2O-Based Nanowires with Immunoglobulin G for Bioimaging

NASA Astrophysics Data System (ADS)

Huong, Nguyen Thanh; Lien, Pham Thi; Hung, Nguyen Manh; Van, Nguyen Duc; Thuy, Tran Thi; Binh, Nguyen Thanh; Minh, Le Quoc

2016-05-01

The surface modification, functionalization, and conjugation of undoped and 11 at.% Eu3+-doped TbPO4 ·H2O nanowires by using silica, a thyocyanate functional group, and immunoglobulin G, respectively, are described in this paper. For the core layer of obtained conjugated nanowires, the undoped TbPO4 ·H2O exhibited characteristic photoluminescent green emission corresponding to 5 D 4 → 7 F J transitions ( J = 6, 5, 4, 3) while the incorporation of Eu3+ into TbPO4 ·H2O lattice was evidenced by Starks splitting transitions at 590, 615, 693 nm of Eu3+ ions for the case of 11 at.% Eu3+-doped TbPO4 ·H2O. The results also indicated that both immunoglobulin G-conjugated undoped and Eu3+-doped TbPO4 ·H2O nanowires can be used in the fluorescent immune analysis as a biomedical label maker to identify measles viruses in vaccine testing.

Pods: a Powder Delivery System for Mars In-situ Organic, Mineralogic and Isotopic Analysis Instruments

NASA Technical Reports Server (NTRS)

Saha, C. P.; Bryson, C. E.; Sarrazin, P.; Blake, D. F.

2005-01-01

Many Mars in situ instruments require fine-grained high-fidelity samples of rocks or soil. Included are instruments for the determination of mineralogy as well as organic and isotopic chemistry. Powder can be obtained as a primary objective of a sample collection system (e.g., by collecting powder as a surface is abraded by a rotary abrasion tool (RAT)), or as a secondary objective (e.g, by collecting drill powder as a core is drilled). In the latter case, a properly designed system could be used to monitor drilling in real time as well as to deliver powder to analytical instruments which would perform complementary analyses to those later performed on the intact core. In addition, once a core or other sample is collected, a system that could transfer intelligently collected subsamples of power from the intact core to a suite of analytical instruments would be highly desirable. We have conceptualized, developed and tested a breadboard Powder Delivery System (PoDS) intended to satisfy the collection, processing and distribution requirements of powder samples for Mars in-situ mineralogic, organic and isotopic measurement instruments.

Polonium 210Po activities in human blood of patients with ischaemic heart disease from Gdańsk in Poland.

PubMed

Boryło, Alicja; Skwarzec, Bogdan; Romańczyk, Grzegorz; Siebert, Janusz

The determination of polonium 210 Po in human blood samples is presented and discussed in this paper. The human blood samples were collected from patients of Medical University of Gdańsk with ischaemic heart disease ( morbus ischaemicus cordis , MIC ). The polonium concentrations in analyzed human blood samples are very differentiated. 210 Po is of particular interest in public health and although is present in the environment in extremely low amounts, it is easily bioaccumulated to the human body. The study shows that the amount of 210 Po that is incorporated into the human body depends on the food habits and some difference in its levels could be observed between smokers and non-smokers.

Multiscale phase mapping of LiFePO4-based electrodes by transmission electron microscopy and electron forward scattering diffraction.

PubMed

Robert, Donatien; Douillard, Thierry; Boulineau, Adrien; Brunetti, Guillaume; Nowakowski, Pawel; Venet, Denis; Bayle-Guillemaud, Pascale; Cayron, Cyril

2013-12-23

LiFePO4 and FePO4 phase distributions of entire cross-sectioned electrodes with various Li content are investigated from nanoscale to mesoscale, by transmission electron microscopy and by the new electron forward scattering diffraction technique. The distributions of the fully delithiated (FePO4) or lithiated particles (LiFePO4) are mapped on large fields of view (>100 × 100 μm(2)). Heterogeneities in thin and thick electrodes are highlighted at different scales. At the nanoscale, the statistical analysis of 64 000 particles unambiguously shows that the small particles delithiate first. At the mesoscale, the phase maps reveal a core-shell mechanism at the scale of the agglomerates with a preferential pathway along the electrode porosities. At larger scale, lithiation occurs in thick electrodes "stratum by stratum" from the surface in contact with electrolyte toward the current collector.

Hemolymph Melanization in the Silkmoth Bombyx mori Involves Formation of a High Molecular Mass Complex That Metabolizes Tyrosine*

PubMed Central

Clark, Kevin D.; Strand, Michael R.

2013-01-01

The phenoloxidase (PO) cascade regulates the melanization of blood (hemolymph) in insects and other arthropods. Most studies indicate that microbial elicitors activate the PO cascade, which results in processing of the zymogen PPO to PO. PO is then thought to oxidize tyrosine and o-diphenols to quinones, which leads to melanin. However, different lines of investigation raise questions as to whether these views are fully correct. Here we report that hemolymph from the silkmoth, Bombyx mori, rapidly melanizes after collection from a wound site. Prior studies indicated that in vitro activated PPO hydroxylates Tyr inefficiently. Measurement of in vivo substrate titers, however, suggested that Tyr was the only PO substrate initially present in B. mori plasma and that it is rapidly metabolized by PO. Fractionation of plasma by gel filtration chromatography followed by bioassays indicated that melanization activity was primarily associated with a high mass complex (∼670 kDa) that contained PO. The prophenoloxidase-activating protease inhibitor Egf1.0 blocked formation of this complex and Tyr metabolism, but the addition of phenylthiourea to plasma before fractionation enhanced complex formation and Tyr metabolism. Mass spectrometry analysis indicated that the complex contained PO plus other proteins. Taken together, our results indicate that wounding alone activates the PO cascade in B. mori. They also suggest that complex formation is required for efficient use of Tyr as a substrate. PMID:23553628

Patterns of, and Factors Associated With, Illicit Pharmaceutical Opioid Analgesic Use in a Prospective Cohort of People Who Inject Drugs in Melbourne, Australia.

PubMed

Horyniak, Danielle; Agius, Paul A; Degenhardt, Louisa; Reddel, Siobhan; Higgs, Peter; Aitken, Campbell; Stoové, Mark; Dietze, Paul

2015-01-01

People who inject drugs (PWID) are a key population engaging in pharmaceutical opioid analgesic (PO) use, yet little is known about patterns of illicit PO use among this group. The aims of this research were to measure the prevalence and frequency of lifetime and past-month illicit PO use and injection in a sample of regular PWID, to examine patterns of past-month illicit PO use within individuals over time, and to identify factors independently associated with past-month illicit PO use. Data were drawn from a prospective cohort study of regular PWID (N = 666) in Melbourne, Australia. Data from five waves of annual data collection (including baseline) were analyzed descriptively and using generalized estimating equations (GEE). At baseline, 59% of participants reported lifetime illicit PO use and 20% reported past-month use, predominantly through injecting. Most illicit PO users at baseline transitioned to nonuse of illicit POs across the study period. In multivariable GEE analysis, factors associated with past-month illicit PO use included past-year arrest [adjusted odds ratio (AOR): 1.39], opioids other than heroin as drug of choice (AOR: 5.14), experiencing poorer physical health (AOR: 0.98) and a range of other drug use variables. We found little evidence of ongoing illicit PO use among those followed up, with illicit PO use linked to polydrug use more broadly. Nonetheless, trends in illicit PO use among PWID should continue to be monitored and harm reduction interventions implemented to reduce the associated public health risks.

STUDY BY AES AND EELS OF InP, InSb, InPO4 AND InxGa1-xAs SUBMITTED TO ELECTRON IRRADIATION

NASA Astrophysics Data System (ADS)

Ghaffour, M.; Abdellaoui, A.; Bouslama, M.; Ouerdane, A.; Al-Douri, Y.

2012-02-01

The surface of materials plays an important role in their technological applications. In the interest to study the stability of materials and their behavior, we irradiate them by the electrons by using the electron spectroscopy such as the Auger electron spectroscopy (AES) and the electron energy loss spectroscopy (EELS). These methods have proved their good sensitivity to study material surfaces. In this paper, we give some results about the effect of the electron beam irradiating the compounds InP, InSb, InPO4 and InxGa1-xAs. The III-V semiconductors InP and InSb seem to be sensitive to the electron irradiation. This breaks the chemical bonds between the element III and V which leads to an oxidation process at the surface. The AES and EELS spectroscopy are also used to characterize the oxide InPO4 whose thickness is about 10 Å grown on the substrate InP(100). The irradiation of the system InPO4/InP(100) by the electron beam of 5 keV energy leads to a structural change of the surface, so that there is breaking of chemical bonds between indium and phosphorus (In-P) and formation of new oxide other than InPO4. In this study we show an important result concerning the effect of the electron beam on the compound InxGa1-xAs by varying the parameter x to obtain In0.2Ga0.8As and In0.53Ga0.47As. It appears that the electron beam affects In0.2Ga0.8As too much in comparison with In0.53Ga0.47As. In the case of the irradiation of In0.2Ga0.8As, there is breaking of chemical bonds between indium and GaAs leading to formation of indium oxide associated to GaAs.

The porous TiO2 nanotubes/Ag3PO4 heterojunction for enhancing sunlight photocatalytic activity

NASA Astrophysics Data System (ADS)

Chi, Chunyan; Pan, Jiaqi; You, Mingzhu; Dong, Zongjun; Zhao, Weijie; Song, Changsheng; Zheng, Yingying; Li, Chaorong

2018-03-01

The porous TiO2 nanotubes/Ag3PO4 heterojunction are synthesized via simple electrospining and chemical co-deposition method. The results of SEM, XRD, TEM and XPS imply that the Ag3PO4 nanoparticles have been introduced on to the surface of TiO2 nanotubes successfully. Compared with the unmodified samples, the photocatalytic activity of the as-prepared porous TiO2 nanotubes/Ag3PO4 heterojunction exhibit a remarkable enhancement by the degradation of methylene blue (MB) under the sunlight. Further, the Z-Scheme structure of the samples and the porous-tubular structure of the TiO2 are considered as the main reasons for the enhancement.

Effect of different polishing systems on the surface roughness of nano-hybrid composites.

PubMed

Patel, Brijesh; Chhabra, Naveen; Jain, Disha

2016-01-01

The study aimed to investigate the influence of different polishing systems on the surface roughness of nano-hybrid composite resins. Different shapes of polishing systems are available according to the site of work. To minimize variability, a new system with single shape is developed that can be utilized in both anterior as well as posterior teeth. Seventy composite discs were fabricated using Teflon well (10 mm × 3 mm). Two main group of nano-hybrid composite Group I - Filtek Z350 and Group II - Tetric N-Ceram were used (n = 35 for each group). Both groups were further divided into four subgroups. Subgroup a - OneGloss (n = 10), Subgroup b - PoGo (n = 10), Subgroup c - Sof-Lex spiral (n = 10), Subgroup d - Mylar strip (control, n = 5). Samples were polished according to the manufacturer's recommendations. Surface roughness test was performed using contact profilometer. The obtained data were analyzed using the one-way analysis of variance test. Tetric N-Ceram produced smoother surfaces than Filtek Z350 (P < 0.05). Mylar strip and "PoGo" created equally smooth surfaces, while significantly rougher surfaces were obtained after applications of "Sof-Lex spiral" and "OneGloss" (P < 0.05). Polishing ability of Tetric N-Ceram is better than Filtek Z350 XT. "PoGo" seems to be a better polishing system than "OneGloss" and "Sof-Lex Spiral."

The Basic Documentation for Psycho-Oncology (PO-Bado): an innovative tool to combine screening for psychological distress and patient support at cancer diagnosis.

PubMed

Stadelmaier, Nena; Duguey-Cachet, Odile; Saada, Yael; Quintard, Bruno

2014-03-01

The Basic Documentation for Psycho-Oncology (PO-Bado) is a semi-directive instrument for assessing psychosocial difficulties in cancer patients. It is based on subjective status and not on degree of symptom severity. Our objectives were to assess whether use of the PO-Bado during post-cancer-diagnosis consultations improves the quality of communication by establishing a supportive relationship between nurses and patients and to assess nurses' satisfaction of their communication skills. Data were collected from post-diagnosis 'bad-news' consultations across four Cancer treatment centres in South West France. Eleven nurses who had never used the PO-Bado ('inexperienced group') received training on the instrument (short-form). Twenty-one pre-training consultations without the PO-Bado were recorded and compared with 21 post-training consultations with the PO-Bado. Twenty consultations with four nurses with experience using the PO-Bado ('experienced group') were included for between-group comparisons. Nurses' satisfaction was evaluated through semi-directive consultations at the end of the study and completed by a visual analogue scale. We transcribed and analysed 62 consultations. We observed greater use of techniques encouraging patient expression in consultations with PO-Bado-experienced nurses (p < 0.01); after PO-Bado training for 'inexperienced' nurses (p < 0.05) and less use of non-encouraging techniques after PO-Bado training for 'inexperienced' nurses (p < 0.01). Nurses felt more satisfied with their communications skills after PO-Bado training and stated that they felt more competent, particularly for referrals to psychologists. The PO-Bado is beneficial for the quality of the communication between nurses and patients at bad-news delivery consultations and for the satisfaction of nurses with regard to their relational skills. Copyright © 2013 John Wiley & Sons, Ltd.

Mechanical properties and in vitro bioactivity of Ca5(PO4)2SiO4 bioceramic.

PubMed

Lu, Wenhao; Duan, Wei; Guo, Yaping; Ning, Congqin

2012-02-01

Pure Ca(5)(PO(4))(2)SiO(4) bioceramic was first prepared by a sol-gel method using triethyl phosphate, tetraethoxysilane, and calcium nitrate tetrahydrate as original materials. Simulated body fluid (SBF) immersion tests revealed that Ca(5)(PO(4))(2)SiO(4) samples had a greater in vitro apatite-forming ability than hydroxyapatite (HA). After soaking Ca(5)(PO(4))(2)SiO(4) samples in the SBF for 1 day, bone-like apatite precipitated on the surfaces and the apatite layer became thicker with increasing the soaking time. However, few bone-like apatites precipitated on the HA samples even after soaking in the SBF for 7 days. The good in vitro bioactivity of Ca(5)(PO(4))(2)SiO(4) samples was attributed to the silanol (Si-OH) groups and greater solubility of Ca(5)(PO(4))(2)SiO(4). In addition, hot-pressed Ca(5)(PO(4))(2)SiO(4) ceramic exhibited lower bending strength and elastic modulus than hot-pressed HA, since the former had a lower relative density than the latter. The results have shown that Ca(5)(PO(4))(2)SiO(4) is a potential candidate material for bone repair. © The Author(s), 2010.

Core/shell-type nanorods of Tb3+-doped LaPO4, modified with amine groups, revealing reduced cytotoxicity

NASA Astrophysics Data System (ADS)

Runowski, Marcin; Dąbrowska, Krystyna; Grzyb, Tomasz; Miernikiewicz, Paulina; Lis, Stefan

2013-11-01

A simple co-precipitation reaction between Ln3+ cations (Ln = lanthanide) and phosphate ions in the presence of polyethylene glycol (PEG), including post-treatment under hydrothermal conditions, leads to the formation of Tb3+-doped LaPO4 crystalline nanorods. The nanoparticles obtained can be successfully coated with amorphous and porous silica, forming core/shell-type nanorods. Both products reveal intensive green luminescence under UV lamp irradiation. The surface of the core/shell-type product can also be modified with -NH2 groups via silylation procedure, using 3-aminopropyltriethoxysilane as a modifier. Powder X-ray diffraction, transmission electron microscopy, and scanning electron microscopy confirm the desired structure and needle-like shape of the products synthesized. Fourier transform infrared spectroscopy and specific surface area measurements by Brunauer-Emmett-Teller method reveal a successful surface modification with amine groups of the core/shell-type nanoparticles prepared. The nanomaterials synthesized exhibit green luminescence characteristic of Tb3+ ions, as solid powders and aqueous colloids, examined by spectrofluorometry. The in vitro cytotoxicity studies reveal different degree toxicity of the products. LaPO4:Tb3+@SiO2@NH2 exhibits the smallest toxicity against B16F0 mouse melanoma cancer cells and human skin microvascular endothelial cell lines, in contrast to the most toxic LaPO4:Tb3+@SiO2.

Core/shell-type nanorods of Tb3+-doped LaPO4, modified with amine groups, revealing reduced cytotoxicity.

PubMed

Runowski, Marcin; Dąbrowska, Krystyna; Grzyb, Tomasz; Miernikiewicz, Paulina; Lis, Stefan

2013-01-01

A simple co-precipitation reaction between Ln 3+ cations (Ln = lanthanide) and phosphate ions in the presence of polyethylene glycol (PEG), including post-treatment under hydrothermal conditions, leads to the formation of Tb 3+ -doped LaPO 4 crystalline nanorods. The nanoparticles obtained can be successfully coated with amorphous and porous silica, forming core/shell-type nanorods. Both products reveal intensive green luminescence under UV lamp irradiation. The surface of the core/shell-type product can also be modified with -NH 2 groups via silylation procedure, using 3-aminopropyltriethoxysilane as a modifier. Powder X-ray diffraction, transmission electron microscopy, and scanning electron microscopy confirm the desired structure and needle-like shape of the products synthesized. Fourier transform infrared spectroscopy and specific surface area measurements by Brunauer-Emmett-Teller method reveal a successful surface modification with amine groups of the core/shell-type nanoparticles prepared. The nanomaterials synthesized exhibit green luminescence characteristic of Tb 3+ ions, as solid powders and aqueous colloids, examined by spectrofluorometry. The in vitro cytotoxicity studies reveal different degree toxicity of the products. LaPO 4 :Tb 3+ @SiO 2 @NH 2 exhibits the smallest toxicity against B16F0 mouse melanoma cancer cells and human skin microvascular endothelial cell lines, in contrast to the most toxic LaPO 4 :Tb 3+ @SiO 2 .

Nutrient loss in leachate and surface runoff from surface-broadcast and subsurface-banded broiler litter.

PubMed

Lamba, Jasmeet; Srivastava, Puneet; Way, Thomas R; Sen, Sumit; Wood, C Wesley; Yoo, Kyung H

2013-09-01

Subsurface band application of poultry litter has been shown to reduce the transport of nutrients from fields in surface runoff compared with conventional surface broadcast application. Little research has been conducted to determine the effects of surface broadcast application and subsurface banding of litter on nutrients in leachate. Therefore, a field experiment was conducted to determine the effects of subsurface band application and surface broadcast application of poultry litter on nutrient losses in leachate. Zero-tension pan and passive capillary fiberglass wick lysimeters were installed in situ 50 cm beneath the soil surface of an established tall fescue ( Schreb.) pasture on a sandy loam soil. The treatments were surface broadcast and subsurface-banded poultry litter at 5 Mg ha and an unfertilized control. Results of the rainfall simulations showed that the concentrations of PO-P and total phosphorus (TP) in leachate were reduced by 96 and 37%, respectively, in subsurface-banded litter treatment compared with the surface-applied litter treatment. There was no significant difference in PO-P concentration between control and subsurface-banded litter treatment in leachate. The trend in the loading of nutrients in leachate was similar to the trend in concentration. Concentration and loading of the nutrients (TP, PO-P, NH-N, and NO-N) in runoff from the subsurface-banded treatment were significantly less than for the surface-applied treatment and were similar to those from control plots. These results show that, compared with conventional surface broadcast application of litter, subsurface band application of litter can greatly reduce loss of P in surface runoff and leachate. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

[Immobilization technology and mechanism of fly ash using H3PO4].

PubMed

Wang, Jun; Jiang, Jian-Guo; Sui, Ji-Chao; Yang, Shi-Jian

2006-08-01

Chemical composition and toxicity leaching characteristics of fly ash was analyzed. The experiment results show that many heavy metals were contained; leaching concentration of Pb is 67.03 mg/L, which exceeds the limit of identification standard for hazardous wastes. Effect of input mass of H3PO4 on immobilization of heavy metals and its long-term environmental stability was studied. The results show that when input 8% - 14% (H3PO4 mass/ fly ash mass) of H3PO4 sound immobilization effect can be achieved; 8% and 12% of H3PO4 will bring a satisfactory environmental stability of heavy metals, while more H3PO4 led to less buffer capacity to acid conditions. In fly ash treated by 12% H3PO4, a small quantity of crystal Cr2P2O7, ZnP2, Pb3P4O13, Pb3P2O7, NaZnPO4, NaPbP3O9, Ca2ZnSi2O7 can be detected by XRD; many independent fly ash particles and bar-shaped Pb5 (PO4)3Cl with a diameter of 0.3 - 0.5 microm were observed by SEM; concentrated heavy metal materials were not obtained by CHBr3 floatation. Conclusions can be drawn that, through neutralization reaction of H3PO4 with strongly alkaline fly ash, stabilization reaction conditions were improved, entrapped heavy metals were chemically activated and PO4(3-) needed in stabilization was produced. Activated heavy metals combined with PO4(3-) on surface of fly ash,generated phosphates existing as forms of solid solution in SiO2, CaCO3, CaSO4, KCl, NaCl.

234Th, 210Pb, 210Po and stable Pb in the central equatorial Pacific: Tracers for particle cycling

USGS Publications Warehouse

Murray, J.W.; Paul, B.; Dunne, J.P.; Chapin, T.

2005-01-01

Samples were collected during the 1992 US JGOFS EqPac Survey I and II cruises from 12??N to 12??S at 140??W in the central equatorial Pacific for water column profiles of dissolved, particulate and total 234Th, 210Pb and 210Po and total acid soluble stable Pb and sediment trap fluxes of 234Th, 210Pb and 210Po. Survey I occurred in February/March with moderate El Nino conditions while Survey II was conducted in September/October when there was a well developed cold-tongue. 234Th, 210Pb and 210Po are all particle reactive yet they partition differently between dissolved and particulate phases. Fractionation factors (the ratios of the distribution coefficients) show that the selectivity for suspended and sediment trap particles follows Th>Po>Pb. Scavenging residence times (??) for 234Th, 210Pb and 210Po ranged from 25 to 100 d, 3 to 8 years and 100 to 500 d, respectively. These particle reactive tracers have very different distributions in the water column, which reflect differences in their sources and sinks. The deficiency of 234Th relative to 238U was fairly uniformly distributed meridionally, though deficiencies were higher during Survey II when there was higher new production. Excess 210Pb relative to 226Ra was very asymmetrical with much higher excess values north of the equator. The distributions were similar for Surveys I and II. The deficiency of 210Po relative to 210Pb had a symmetrical distribution about the equator for both Survey I and II but the deficiencies were larger during Survey I when upwelling was smaller. Stable Pb was generally higher at the surface than at 250 m and there was no meridional trend from 12??N to 12??S. A mass balance for 210Pb was used to determine the atmospheric input of 210Pb. The average values for Surveys I and II were 0.12 and 0.32 dpm cm-2 year-1, respectively. There was no general increase in atmospheric input of 210Pb north of the equator but there was a strong maximum at 2-3??N during Survey I coincident with the location of the intertropical convergence zone (ITCZ), suggesting a large role for wet deposition. A mass balance for stable Pb was used to determine the atmospheric input of stable Pb. Results ranged from 110 to 140 pmol cm-2 year-1. This flux was low in the southern hemisphere and increased steadily north of the equator. We evaluated use of 210Po as a tracer for export of particulate organic matter during Survey I. Organic carbon and 210Po were highly correlated in suspended matter and sediment trap samples. Average values of organic carbon fluxes determined from the deficiencies of 210Po times the orgC/210Po ratio agreed well with those determined from the deficiencies of 234Th times the organic carbon/234Th ratio and 15N-new production, but had a much larger variability because of the more variable advection corrections. ?? 2005 Elsevier Ltd. All rights reserved.

Automated River Reach Definition Strategies: Applications for the Surface Water and Ocean Topography Mission

NASA Astrophysics Data System (ADS)

Frasson, Renato Prata de Moraes; Wei, Rui; Durand, Michael; Minear, J. Toby; Domeneghetti, Alessio; Schumann, Guy; Williams, Brent A.; Rodriguez, Ernesto; Picamilh, Christophe; Lion, Christine; Pavelsky, Tamlin; Garambois, Pierre-André

2017-10-01

The upcoming Surface Water and Ocean Topography (SWOT) mission will measure water surface heights and widths for rivers wider than 100 m. At its native resolution, SWOT height errors are expected to be on the order of meters, which prevent the calculation of water surface slopes and the use of slope-dependent discharge equations. To mitigate height and width errors, the high-resolution measurements will be grouped into reaches (˜5 to 15 km), where slope and discharge are estimated. We describe three automated river segmentation strategies for defining optimum reaches for discharge estimation: (1) arbitrary lengths, (2) identification of hydraulic controls, and (3) sinuosity. We test our methodologies on 9 and 14 simulated SWOT overpasses over the Sacramento and the Po Rivers, respectively, which we compare against hydraulic models of each river. Our results show that generally, height, width, and slope errors decrease with increasing reach length. However, the hydraulic controls and the sinuosity methods led to better slopes and often height errors that were either smaller or comparable to those of arbitrary reaches of compatible sizes. Estimated discharge errors caused by the propagation of height, width, and slope errors through the discharge equation were often smaller for sinuosity (on average 8.5% for the Sacramento and 6.9% for the Po) and hydraulic control (Sacramento: 7.3% and Po: 5.9%) reaches than for arbitrary reaches of comparable lengths (Sacramento: 8.6% and Po: 7.8%). This analysis suggests that reach definition methods that preserve the hydraulic properties of the river network may lead to better discharge estimates.

Cr-substituted LiCoPO4 core with a conductive carbon layer towards high-voltage lithium-ion batteries

NASA Astrophysics Data System (ADS)

Wang, Yue; Chen, Junhong; Qiu, Jingyi; Yu, Zhongbao; Ming, Hai; Li, Meng; Zhang, Songtong; Yang, Yusheng

2018-02-01

Electrical and ionic conductivity are two major limiting factors for LiCoPO4 cathode material. To overcome these shortcomings, a Cr-substituted LiCoPO4 core with a conductive carbon layer cathode material is synthesized using the sol-gel method. The physical chemistry properties of these materials are systematically investigated by using various characterization methods. For instance, the XRD and Rietveld refinement results reveal that Cr successfully substitutes the Co within the LiCoPO4 core to form LiCo1-1.5xCrxPO4/C (x = 0, 0.02, 0.04, 0.06) without changing the olivine structure but exhibits a decrease in the unit cell volume with increasing Cr substitution. SEM and TEM images indicate that Cr substitution does not lead to changes in the basic morphology of LiCo1-1.5xCrxPO4/C (x = 0, 0.02, 0.04, 0.06) material, which is composed of agglomerated nanoparticles with an 8 nm carbon layer on the surface. The EDS and XPS results confirm that Cr is uniformly distributed on the surface and that the oxidation state of Cr is +3. FTIR spectra indicate that the antisite defect concentration decreases with increasing Cr substitution. Furthermore, Cr substitution significantly improves the electrochemical performances of LiCo1-1.5xCrxPO4/C (x = 0.02, 0.04, 0.06) cathode. Notably, the LiCo0.94Cr0.04PO4/C delivers an initial discharge capacity of 144 mA h g-1 at 0.1 C and shows a capacity retention of 71% after 100 cycles between 3.0 and 5.0 V. The CV and EIS results indicate that the polarization is reduced and that the electronic and ionic conductivities are improved by Cr substitution. The good electrochemical performances for Cr-substituted LiCoPO4/C electrodes are attributed to the lower antisite defect concentration, as the reduction of polarization, the improvement of electronic and ion conductivity and the uniform carbon layer. These features will accelerate the commercial application of LiCoPO4 towards the start-art of the high voltage lithium-ion batteries.

Seasonal trend of fog water chemical composition in the Po Valley.

PubMed

Fuzzi, S; Facchini, M C; Orsi, G; Ferri, D

1992-01-01

Fog frequency in the Po Valley, Northern Italy, can be as high as 30% of the time in the fall-winter season. High pollutant concentrations have been measured in fog water samples collected in this area over the past few years. The combined effects of high fog occurrence and high pollutant loading of the fog droplets can determine, in this area, appreciable chemical deposition rates. An automated station for fog water collection was developed, and deployed at the field station of S. Pietro Capofiume, in the eastern part of the Po Valley for an extended period: from the beginning of November 1989 to the end of April 1990. Time-resolved sampling of fog droplets was carried out during all fog events occurring in this period, and chemical analyses were performed on the collected samples. Statistical information on fog occurrence and fog water chemical composition is reported in this paper, and a tentative seasonal deposition budget is calculated for H+, NH4+, NO3- and SO4(2-) ions. The problems connected with fog droplet sampling in sub-freezing conditions are also addressed in the paper.

Light-dependent controlled synthesis and photocatalytic properties of stable Ag{sub 3} nanocrystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Jian-Dong; Liu, Jin-Ku, E-mail: jkliu@ecust.edu.cn; Luo, Chong-Xiao

2014-12-15

The silver phosphate (Ag{sub 3}PO{sub 4}) is applied in organic matter photodegradation as a novel catalyst materials, however, its instability reduces the photocatalytic life and limits its further applications. In this work, a series of Ag{sub 3}PO{sub 4} crystalline nanoparticle clusters have been synthesized by a photocontrol method. By comparing their sunlight photocatalytic properties, the Ag{sub 3}PO{sub 4} nanoparticles with dominant (2 2 0) facets have a lower surface energy (1.05 J m{sup −2}) than existing Ag{sub 3}PO{sub 4} crystals which can offer a longer catalyst service life. The photodegradation rate of the Ag{sub 3}PO{sub 4} nanoparticles is about 3more » times that of common Ag{sub 3}PO{sub 4} bulk materials and the sunlight is used as the power source instead of high cost artificial visible light sources in this catalytic system. An effective continuous photodegradation reactor using Ag{sub 3}PO{sub 4} nanoparticles is successfully fabricated to degrade rhodamine B solution. At the same time, this work provides an example for how oxidation photocatalyst works without extra adding sacrificial reagent.« less

In situ Raman spectroscopy of LiFePO4: size and morphology dependence during charge and self-discharge.

PubMed

Wu, Jing; Dathar, Gopi Krishna Phani; Sun, Chunwen; Theivanayagam, Murali G; Applestone, Danielle; Dylla, Anthony G; Manthiram, Arumugam; Henkelman, Graeme; Goodenough, John B; Stevenson, Keith J

2013-10-25

Previous studies of the size dependent properties of LiFePO4 have focused on the diffusion rate or phase transformation pathways by bulk analysis techniques such as x-ray diffraction (XRD), neutron diffraction and electrochemistry. In this work, in situ Raman spectroscopy was used to study the surface phase change during charge and self-discharge on a more localized scale for three morphologies of LiFePO4: (1) 25 ± 6 nm width nanorods, (2) 225 ± 6 nm width nanorods and (3) ∼2 μm porous microspheres. Both the large nanorod and microsphere geometries showed incomplete delithiation at the end of charge, which was most likely caused by anti-site defects along the 1D diffusion channels in the bulk of the larger particles. Based on the in situ Raman measurements, all of the morphologies studied exhibited self-discharge with time. Among them, the smallest FePO4 particles self-discharged (lithiated) the fastest. While nanostructuring LiFePO4 can offer advantages in terms of lowering anti-site defects within particles, it also creates new problems due to high surface energies that allow self-discharge. The in situ Raman spectroscopy also showed that carbon coating did not provide significant improvement to the stability of the lithiated particles.

Exposure to radionuclides in smoke from vegetation fires.

PubMed

Carvalho, Fernando P; Oliveira, João M; Malta, Margarida

2014-02-15

Naturally occurring radionuclides of uranium, thorium, radium, lead and polonium were determined in bushes and trees and in the smoke from summer forest fires. Activity concentrations of radionuclides in smoke particles were much enriched when compared to original vegetation. Polonium-210 ((210)Po) in smoke was measured in concentrations much higher than all other radionuclides, reaching 7,255 ± 285 Bq kg(-1), mostly associated with the smaller size smoke particles (<1.0 μm). Depending on smoke particle concentration, (210)Po in surface air near forest fires displayed volume concentrations up to 70 m Bq m(-3), while in smoke-free air (210)Po concentration was about 30 μ Bq m(-3). The estimated absorbed radiation dose to an adult member of the public or a firefighter exposed for 24h to inhalation of smoke near forest fires could exceed 5 μSv per day, i.e, more than 2000 times above the radiation dose from background radioactivity in surface air, and also higher than the radiation dose from (210)Po inhalation in a chronic cigarette smoker. It is concluded that prolonged exposure to smoke allows for enhanced inhalation of radionuclides associated with smoke particles. Due to high radiotoxicity of alpha emitting radionuclides, and in particular of (210)Po, the protection of respiratory tract of fire fighters is strongly recommended. Copyright © 2013 Elsevier B.V. All rights reserved.

Surface chemistry from wettability and charge for the control of mesenchymal stem cell fate through self-assembled monolayers.

PubMed

Hao, Lijing; Fu, Xiaoling; Li, Tianjie; Zhao, Naru; Shi, Xuetao; Cui, Fuzhai; Du, Chang; Wang, Yingjun

2016-12-01

Self-assembled monolayers (SAMs) of alkanethiols on gold are highly controllable model substrates and have been employed to mimic the extracellular matrix for cell-related studies. This study aims to systematically explore how surface chemistry influences the adhesion, morphology, proliferation and osteogenic differentiation of mouse mesenchymal stem cells (mMSCs) using various functional groups (-OEG, -CH 3 , -PO 3 H 2 , -OH, -NH 2 and -COOH). Surface analysis demonstrated that these functional groups produced a wide range of wettability and charge: -OEG (hydrophilic and moderate iso-electric point (IEP)), -CH 3 (strongly hydrophobic and low IEP), -PO 3 H 2 (moderate wettability and low IEP), -OH (hydrophilic and moderate IEP), -NH 2 (moderate wettability and high IEP) and -COOH (hydrophilic and low IEP). In terms of cell responses, the effect of wettability may be more influential than charge for these groups. Moreover, compared to -OEG and -CH 3 groups, -PO 3 H 2 , -OH, -NH 2 and -COOH functionalities tended to promote not only cell adhesion, proliferation and osteogenic differentiation but also the expression of α v and β 1 integrins. This finding indicates that the surface chemistry may guide mMSC activities through α v and β 1 integrin signaling pathways. Model surfaces with controllable chemistry may provide insight into biological responses to substrate surfaces that would be useful for the design of biomaterial surfaces. Copyright © 2016 Elsevier B.V. All rights reserved.

The preparation and graphene surface coating NaTi2(PO4)3 as cathode material for lithium ion batteries

NASA Astrophysics Data System (ADS)

Li, Na; Wang, Yanping; Rao, Richuan; Dong, Xiongzi; Zhang, Xianwen; Zhu, Sane

2017-03-01

The graphene coated NaTi2(PO4)3 has been fabricated via a simple sol-gel process followed by calcination. The NaTi2(PO4)3/graphene (NTP/G) composite is used directly as cathode electrode material for lithium-ion battery and the electrochemical properties of the composite in this system is firstly studied in detail. In the charge-discharge process, two Li+ can occupy octahedral M (2) site and be reversibly intercalated into the 3D framework of NTP through the ion conduction channel where almost all of Na+ are immobilized to sustain the framework. At 5C rate, the capacity retention of the NTP/G composite after 800 cycles is still up to 82.7%. The superior electrochemical properties of NTP/G is ascribed to its stable 3-D framework and the enhanced electronic conduction resulting from the graphene sheets surface modification.

Hydrophobic and Metallophobic Surfaces: Highly Stable Non-wetting Inorganic Surfaces Based on Lanthanum Phosphate Nanorods

NASA Astrophysics Data System (ADS)

Sankar, Sasidharan; Nair, Balagopal N.; Suzuki, Takehiro; Anilkumar, Gopinathan M.; Padmanabhan, Moothetty; Hareesh, Unnikrishnan Nair S.; Warrier, Krishna G.

2016-03-01

Metal oxides, in general, are known to exhibit significant wettability towards water molecules because of the high feasibility of synergetic hydrogen-bonding interactions possible at the solid-water interface. Here we show that the nano sized phosphates of rare earth materials (Rare Earth Phosphates, REPs), LaPO4 in particular, exhibit without any chemical modification, unique combination of intrinsic properties including remarkable hydrophobicity that could be retained even after exposure to extreme temperatures and harsh hydrothermal conditions. Transparent nanocoatings of LaPO4 as well as mixture of other REPs on glass surfaces are shown to display notable hydrophobicity with water contact angle (WCA) value of 120° while sintered and polished monoliths manifested WCA greater than 105°. Significantly, these materials in the form of coatings and monoliths also exhibit complete non-wettability and inertness towards molten metals like Ag, Zn, and Al well above their melting points. These properties, coupled with their excellent chemical and thermal stability, ease of processing, machinability and their versatile photo-physical and emission properties, render LaPO4 and other REP ceramics utility in diverse applications.

Hydrophobic and Metallophobic Surfaces: Highly Stable Non-wetting Inorganic Surfaces Based on Lanthanum Phosphate Nanorods.

PubMed

Sankar, Sasidharan; Nair, Balagopal N; Suzuki, Takehiro; Anilkumar, Gopinathan M; Padmanabhan, Moothetty; Hareesh, Unnikrishnan Nair S; Warrier, Krishna G

2016-03-09

Metal oxides, in general, are known to exhibit significant wettability towards water molecules because of the high feasibility of synergetic hydrogen-bonding interactions possible at the solid-water interface. Here we show that the nano sized phosphates of rare earth materials (Rare Earth Phosphates, REPs), LaPO4 in particular, exhibit without any chemical modification, unique combination of intrinsic properties including remarkable hydrophobicity that could be retained even after exposure to extreme temperatures and harsh hydrothermal conditions. Transparent nanocoatings of LaPO4 as well as mixture of other REPs on glass surfaces are shown to display notable hydrophobicity with water contact angle (WCA) value of 120° while sintered and polished monoliths manifested WCA greater than 105°. Significantly, these materials in the form of coatings and monoliths also exhibit complete non-wettability and inertness towards molten metals like Ag, Zn, and Al well above their melting points. These properties, coupled with their excellent chemical and thermal stability, ease of processing, machinability and their versatile photo-physical and emission properties, render LaPO4 and other REP ceramics utility in diverse applications.

Synthesis of silica aerogel monoliths with controlled specific surface areas and pore sizes

NASA Astrophysics Data System (ADS)

Gao, Bingying; Lu, Shaoxiang; Kalulu, Mulenga; Oderinde, Olayinka; Ren, Lili

2017-07-01

To replace traditional preparation methods of silica aerogels, a small-molecule 1,2-epoxypropane (PO) has been introduced into the preparation process instead of using ammonia as the cross-linking agent, thus generating a lightweight, high porosity, and large surface area silica aerogel monolithic. We put forward a simple solution route for the chemical synthesis of silica aerogels, which was characterized by scanning electron microscopy (SEM), TEM, XRD, FTIR, thermogravimetric analysis (TGA) and the Brunauer-Emmett-Teller (BET) method In this paper, the effect of the amount of PO on the microstructure of silica aerogels is discussed. The BET surface areas and pore sizes of the resulting silica aerogels can be freely adjusted by changing the amount of PO, which will be helpful in promoting the development of silica aerogels to fabricate other porous materials with similar requirements. We also adopted a new organic solvent sublimation drying (OSSD) method to replace traditional expensive and dangerous drying methods such as critical point drying and freeze drying. This simple approach is easy to operate and has good repeatability, which will further facilitate actual applications of silica aerogels.

Characterization of nephelium mutabile blume-like structure of carbon nanotubes prepared from palm oil by CVD method

NASA Astrophysics Data System (ADS)

Maryam, M.; Shamsudin, M. S.; Rusop, M.

2017-09-01

A new structure of carbon nanotube was produced from the Single furnace Aerosol-assisted Catalytic CVD (SFAACVD) method using Palm Oil (PO) as the precursor and Ferrocene (Fe) as the catalyst. A nephelium mutabile blume (rambutan)-like structure of CNTs was found from the black substance collected from the Alumina boat substrate placed inside the furnace. Temperature of furnace which was heated at 600 °C - 800 °C plays an important role in determining the formation of structure. The formation rambutan-like structure of CNTs was optimized at 700 °C and the samples collected were characterized by Field Emission Scanning Electron Microscope (FE-SEM) to obtain the surface morphologies. Raman Spectroscopy (RS) and Thermogravimetric Analysis (TGA) were then used to further study the Raman Spectra and purity of samples.

A study on possible use of Urtica dioica (common nettle) plant as polonium (210)Po and lead (210)Pb contamination biomonitor in the area of phosphogypsum stockpile.

PubMed

Olszewski, Grzegorz; Boryło, Alicja; Skwarzec, Bogdan

2016-04-01

The aim of this study was to test a possible use of Urtica dioica (common nettle) plant as a biomonitor of polonium (210)Po and lead (210)Pb contamination near phosphogypsum stacks by determining concentrations of these radionuclides in samples collected from the area of phosphogypsum stockpile in Wiślinka (northern Poland). The (210)Po and (210)Pb contents in roots depended on their concentrations in soils. Bioconcentration factor values from soil to root of the plant did not depend on (210)Po and (210)Pb contents in soils that leads to the conclusion that different polonium and lead species have different affinities to U. dioica plants. The main sources of both analyzed radionuclides in green parts of plants are wet and dry air deposition and transportation from soil. The values of (210)Po/(210)Pb activity ratio indicate natural origin of these radioisotopes in analyzed plants. (210)Po and (210)Pb concentration in U. dioica roots is negatively weakly correlated with distance from phosphogypsum stockpile.

Effects of sol-gel processed silica coating on bond strength of resin cements to glass-infiltrated alumina ceramic.

PubMed

Xie, Haifeng; Wang, Xiaozu; Wang, Yu; Zhang, Feimin; Chen, Chen; Xia, Yang

2009-02-01

The aim of this study was to verify the effects of sol-gel processed silica coating on the bond strength between resin cement and glass-infiltrated aluminum oxide ceramic. Silica coatings were prepared on glass-infiltrated aluminum oxide ceramic surface via the sol-gel process. Atomic Force Microscope (AFM), Fourier Transmission Infrared spectrum (FTIR), and Energy Dispersive X-ray Spectroscopy (EDS) were used for coating characterization. Forty-eight blocks of glass-infiltrated aluminum oxide ceramic were fabricated. The ceramic surfaces were polished following sandblasting. Three groups of specimens (16 for each group) with different surface treatment were prepared. Group P: no treatment; group PO: treated with silane solution; group PTO: silica coating via sol-gel process, followed by silane application. Composite cylinders were luted with resin cement to the test specimens. Half of the specimens in each group were stored in distilled water for 24 h and the other half were stored in distilled water for 30 days before shear loading in a universal testing machine until failure. Selected ceramic surfaces were analyzed to identify the failure mode using a scanning electron microscopy (SEM). Nanostructured silica coatings were prepared on glass-infiltrated aluminum oxide ceramic surfaces by the sol-gel process. The silicon element on the ceramic surface increased significantly after the coating process. The mean shear bond strength values (standard deviation) before artificial aging were: group P: 1.882 +/- 0.156 MPa; group PO: 2.177 +/- 0.226 MPa; group PTO: 3.574 +/- 0.671 MPa. Statistically significant differences existed between group PTO and group P, and group PTO and groups PO. The failure mode for group P and group PO was adhesive, while group PTO was mixed. The mean shear bond strength values (standard deviation) after artificial aging were: group P: 1.594 +/- 0.111 MPa; group PO: 2.120 +/- 0.339 MPa; group PTO: 2.955 +/- 0.113 MPa. Statistically significant differences existed between each two groups after artificial aging, group P had the lowest bond durability, and group PTO had the highest bond durability. The sol-gel process is an effective way to prepare silica coating on dental glass-infiltrated alumina ceramic. Sol-gel processed silica coating can improve the resin bond strength of glass-infiltrated alumina ceramic.

Self-Assembly of Antisite Defectless nano-LiFePO4 @C/Reduced Graphene Oxide Microspheres for High-Performance Lithium-Ion Batteries.

PubMed

Wang, Hongbin; Liu, Lijia; Wang, Runwei; Yan, Xiao; Wang, Ziqi; Hu, Jiangtao; Chen, Haibiao; Jiang, Shang; Ni, Ling; Qiu, Hailong; Tang, Haitong; Wei, Yingjin; Zhang, Zongtao; Qiu, Shilun; Pan, Feng

2018-05-18

LiFePO 4 @C/reduced graphene oxide (rGO) hierarchical microspheres with superior electrochemical activity and a high tap density were first synthesized by using a Fe 3+ -based single inorganic precursor (LiFePO 4 OH@RF/GO; RF=resorcinol-formaldehyde, GO=graphene oxide) obtained from a template-free self-assembly synthesis followed by direct calcination. The synthetic process requires no physical mixing step. The phase transformation pathway from tavorite LiFePO 4 OH to olivine LiFePO 4 upon calcination was determined by means of the in situ high-temperature XRD technique. Benefitting from the unique structure of the material, these microspheres can be densely packed together, giving a high tap density of 1.3 g cm -3 , and simultaneously, defectless LiFePO 4 primary nanocrystals modified with a highly conductive surface carbon layer and ultrathin rGO provide good electronic and ionic kinetics for fast electron/Li + ion transport. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Investigations of the partitioning and residence times of Po-210 and Pb-210 in a riverine system in Southeast Michigan, USA.

PubMed

Mudbidre, R; Baskaran, M; Schweitzer, L

2014-12-01

Some of the daughter products in the (222)Rn-decay series, such as (210)Po and (210)Pb, have been widely used as tracers and chronometers in aqueous systems. We measured the concentrations of (210)Pb and (210)Po in the dissolved (≤0.5 μm), bulk (unfiltered) and particulate phases (≥1 μm) collected in the Clinton River in the Lake St. Clair watershed in Southeast Michigan in order to investigate their partitioning between particulate and dissolved phases. Activity measurements of the dissolved and particulate phases revealed that an average of 38% (range: 12-59%) and 33% (range: 12-66%) of the total (210)Pb and (210)Po, respectively, in the water column was found in the particulate phase. The activity of dissolved and total (210)Pb was higher than that of (210)Po because of the higher atmospheric depositional fluxes of (210)Pb compared to (210)Po. Although the calculated Kd values of (210)Pb and (210)Po were similar, there was an inverse relationship between the Kd and suspended particulate matter concentration, indicating the presence of a particle concentration effect and we attribute this observation to the presence of significant amounts of colloidal (210)Po and (210)Pb in the dissolved phase. The fractionation factors for Po and Pb were found to be less than 1 in most cases. The first-order box model calculation-based residence times with respect to scavenging varied from 2 to 25 days for (210)Pb and 19-78 days for (210)Po, indicating higher particle-reactivity of (210)Pb compared to (210)Po. Copyright © 2014 Elsevier Ltd. All rights reserved.

Endangered Right Whales Enhance Primary Productivity in the Bay of Fundy

PubMed Central

Roman, Joe; Nevins, John; Altabet, Mark; Koopman, Heather; McCarthy, James

2016-01-01

Marine mammals have recently been documented as important facilitators of rapid and efficient nutrient recycling in coastal and offshore waters. Whales enhance phytoplankton nutrition by releasing fecal plumes near the surface after feeding and by migrating from highly productive, high-latitude feeding areas to low-latitude nutrient-poor calving areas. In this study, we measured NH4+ and PO43- release rates from the feces of North Atlantic right whales (Eubalaena glacialis), a highly endangered baleen whale. Samples for this species were primarily collected by locating aggregations of whales in surface-active groups (SAGs), which typically consist of a central female surrounded by males competing for sexual activity. When freshly collected feces were incubated in seawater, high initial rates of N release were generally observed, which decreased to near zero within 24 hours of sampling, a pattern that is consistent with the active role of gut microflora on fecal particles. We estimate that at least 10% of particulate N in whale feces becomes available as NH4+ within 24 hours of defecation. Phosphorous was also abundant in fecal samples: initial release rates of PO43- were higher than for NH4+, yielding low N/P nutrient ratios over the course of our experiments. The rate of PO43- release was thus more than sufficient to preclude the possibility that nitrogenous nutrients supplied by whales would lead to phytoplankton production limited by P availability. Phytoplankton growth experiments indicated that NH4+ released from whale feces enhance productivity, as would be expected, with no evidence that fecal metabolites suppress growth. Although North Atlantic right whales are currently rare (approximately 450 individuals), they once numbered about 14,000 and likely played a substantial role in recycling nutrients in areas where they gathered to feed and mate. Even though the NH4+ released from fresh whale fecal material is a small fraction of total whale fecal nitrogen, and recognizing the fact that the additional nitrogen released in whale urine would be difficult to measure in a field study, the results of this study support the idea that the distinctive isotopic signature of the released NH4+ could be used to provide a conservative estimate of the contribution of the whale pump to primary productivity in coastal regions where whales congregate. PMID:27331902

Endangered Right Whales Enhance Primary Productivity in the Bay of Fundy.

PubMed

Roman, Joe; Nevins, John; Altabet, Mark; Koopman, Heather; McCarthy, James

2016-01-01

Marine mammals have recently been documented as important facilitators of rapid and efficient nutrient recycling in coastal and offshore waters. Whales enhance phytoplankton nutrition by releasing fecal plumes near the surface after feeding and by migrating from highly productive, high-latitude feeding areas to low-latitude nutrient-poor calving areas. In this study, we measured NH4+ and PO43- release rates from the feces of North Atlantic right whales (Eubalaena glacialis), a highly endangered baleen whale. Samples for this species were primarily collected by locating aggregations of whales in surface-active groups (SAGs), which typically consist of a central female surrounded by males competing for sexual activity. When freshly collected feces were incubated in seawater, high initial rates of N release were generally observed, which decreased to near zero within 24 hours of sampling, a pattern that is consistent with the active role of gut microflora on fecal particles. We estimate that at least 10% of particulate N in whale feces becomes available as NH4+ within 24 hours of defecation. Phosphorous was also abundant in fecal samples: initial release rates of PO43- were higher than for NH4+, yielding low N/P nutrient ratios over the course of our experiments. The rate of PO43- release was thus more than sufficient to preclude the possibility that nitrogenous nutrients supplied by whales would lead to phytoplankton production limited by P availability. Phytoplankton growth experiments indicated that NH4+ released from whale feces enhance productivity, as would be expected, with no evidence that fecal metabolites suppress growth. Although North Atlantic right whales are currently rare (approximately 450 individuals), they once numbered about 14,000 and likely played a substantial role in recycling nutrients in areas where they gathered to feed and mate. Even though the NH4+ released from fresh whale fecal material is a small fraction of total whale fecal nitrogen, and recognizing the fact that the additional nitrogen released in whale urine would be difficult to measure in a field study, the results of this study support the idea that the distinctive isotopic signature of the released NH4+ could be used to provide a conservative estimate of the contribution of the whale pump to primary productivity in coastal regions where whales congregate.

Increasing the Affinity Between Carbon-Coated LiFePO4/C Electrodes and Conventional Organic Electrolyte by Spontaneous Grafting of a Benzene-Trifluoromethylsulfonimide Moiety.

PubMed

Delaporte, Nicolas; Perea, Alexis; Lebègue, Estelle; Ladouceur, Sébastien; Zaghib, Karim; Bélanger, Daniel

2015-08-26

The grafting of benzene-trifluoromethylsulfonimide groups on LiFePO4/C was achieved by spontaneous reduction of in situ generated diazonium ions of the corresponding 4-amino-benzene-trifluoromethylsulfonimide. The diazotization of 4-amino-benzene-trifluoromethylsulfonimide was a slow process that required a high concentration of precursors to promote the spontaneous grafting reaction. Contact angle measurements showed a hydrophilic surface was produced after the reaction that is consistent with grafting of benzene-trifluoromethylsulfonimide groups. Elemental analysis data revealed a 2.1 wt % loading of grafted molecules on the LiFePO4/C powder. Chemical oxidation of the cathode material during the grafting reaction was detected by X-ray diffraction and quantified by inductively coupled plasma atomic emission spectrometry. Surface modification improves the wettability of the cathode material, and better discharge capacities were obtained for modified electrodes at high C-rate. In addition, electrochemical impedance spectroscopy showed the resistance of the modified cathode was lower than that of the bare LiFePO4/C film electrode. Moreover, the modified cathode displayed superior capacity retention after 200 cycles of charge/discharge at 1 C.

Coating effect of LiFePO4 and Al2O3 on Li1.2Mn0.54Ni0.13Co0.13O2 cathode surface for lithium ion batteries

NASA Astrophysics Data System (ADS)

Seteni, Bonani; Rapulenyane, Nomasonto; Ngila, Jane Catherine; Mpelane, Siyasanga; Luo, Hongze

2017-06-01

Lithium-manganese-rich cathode material Li1.2Mn0.54Ni0.13Co0.13O2 is prepared by combustion method, and then coated with nano-sized LiFePO4 and nano-sized Al2O3 particles via a wet chemical process. The as-prepared Li1.2Mn0.54Ni0.13Co0.13O2, LiFePO4-coated Li1.2Mn0.54Ni0.13Co0.13O2 and Al2O3-coated Li1.2Mn0.54Ni0.13Co0.13O2 are characterized by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The scanning electron microscopy shows the agglomeration of the materials and their nanoparticle size ∼100 nm. The transmission electron microscopy confirms that LiFePO4 forms a rough mat-like surface and Al2O3 remain as islandic particles on the surface of the Li1.2Mn0.54Ni0.13Co0.13O2 material. The Li1.2Mn0.54Ni0.13Co0.13O2 coated with LiFePO4 and Li1.2Mn0.54Ni0.13Co0.13O2 coated with Al2O3 exhibits improved electrochemical performance. The initial discharge capacity is enhanced to 267 mAhg-1 after the LiFePO4 coating and 285 mAhg-1 after the Al2O3 coating compared to the as-prepared Li1.2Mn0.54Ni0.13Co0.13O2 material that has an initial discharge capacity of 243 mAhg-1. Galvanostatic charge-discharge tests at C/10 display longer activation of Li2MnO3 phase and higher capacity retention of 88% after 20 cycles for Li1.2Mn0.54Ni0.13Co0.13O2-LiFePO4 compared to Li1.2Mn0.54Ni0.13Co0.13O2-Al2O3 of 80% after 20 cycles and LMNC of 80% after 20 cycles. Meanwhile Li1.2Mn0.54Ni0.13Co0.13O2-LiFePO4 also shows higher rate capability compared to Li1.2Mn0.54Ni0.13Co0.13O2-Al2O3.

Compositional analysis and pollution impact assessment: A case study in the Gulfs of Naples and Salerno

NASA Astrophysics Data System (ADS)

Menghan, Wang; Stefano, Albanese; Annamaria, Lima; Claudia, Cannatelli; Antonio, Cosenza; Wanjun, Lu; Marco, Sacchi; Angela, Doherty; Benedetto, De Vivo

2015-07-01

This paper presents the results of an environmental geochemical investigation of the Gulfs of Naples and Salerno, near the Campania plain (Southern Italy). Surface marine sediment samples were collected during three field campaigns: 96 from the Gulfs of Naples and Salerno (NaSa); 123 from the Bagnoli site coastal area (BaSi); and 11 from the ports around the Gulf of Naples (PoNa). Elemental concentrations were determined and their interpolated distribution maps were compiled. Three geochemical sources (or processes) were determined associating elemental distribution with the results obtained from a R-mode factor analysis: 1) geogenic, 2) water kinetics and 3) anthropogenic. The results are presented as raw data single element distributions of eight potential toxic elements (PTEs) (As, Cd, Cr, Cu, Hg, Pb, Ni and Zn) in the forms of raw data and additive log-ratio transformed data. The latter showed advantages in revealing the actual distribution patterns. Geochemical background reference values of PTEs were determined from the median value of local background reference values. Based on these values, pollution impact analysis was carried out to both BaSi and PoNa samples, indicating most of BaSi and PoNa sediments were affected by moderate to strong Pb, Zn, Cd and Hg pollution. An ecological risk assessment was subsequently carried out on the entire database, pointing a toxic risk ranking in the order Pb > As > Ni > Cd > Hg > Cr.

Is the effect of person-organisation fit on turnover intention mediated by job satisfaction? A survey of community health workers in China

PubMed Central

Yan, Fei; Wang, Wei; Li, Guohong

2017-01-01

Objectives Person-organisation fit (P-O fit) is a predictor of work attitude. However, in the area of human resource for health, the literature of P-O fit is quite limited. It is unclear whether P-O fit directly or indirectly affects turnover intention. This study aims to examine the mediation effect of job satisfaction on the relationship between P-O fit and turnover intention based on data from China. Design and methods This is a cross-sectional survey of community health workers (CHWs) in China in 2013. A questionnaire of P-O fit, job satisfaction and turnover intention was developed, and its validity and reliability were assessed. Multiple regression and structural equation modelling were used to examine the relationship among P-O fit, job satisfaction and turnover intention. Setting and participants Multistage sampling was applied. In total, 656 valid questionnaire responses were collected from CHWs in four provincial regions in China, namely Shanghai, Shaanxi, Shandong and Anhui. Results P-O fit was directly related to job satisfaction (standardised β 0.246) and inversely related to turnover intention (standardised β −0.186). In the mediation model, the total effect of P-O fit on turnover intention was −0.186 (p<0.001); the direct effect of P-O fit on turnover intention was −0.094 (p<0.01); the indirect effect of job satisfaction on the relationship between P-O fit and turnover intention was −0.092 (p<0.001). Conclusions The effect of P-O fit on turnover intention was partially mediated through job satisfaction. It is suggested that more work attitude variables and different dimensions of P-O fit be taken into account to examine the complete mechanism of person-organisation interaction. Indirect measures of P-O fit should be encouraged in practice to enhance work attitudes of health workers. PMID:28399513

Prescription opioid related misuse, harms, diversion and interventions in Canada: a review.

PubMed

Fischer, Benedikt; Argento, Elena

2012-07-01

The non-medical use of and harms related to prescription opioid (PO) analgesics - key medications to treat severe and chronic pain - are an emerging public health concern globally. PO use is proportionally highest in North America, where, consequently, nonmedical PO use (NMPOU) and morbidity/mortality are high and well documented for the United States. Canada is the country with the second highest PO consumption rate in the world - with steeper recent increases in PO use than the US - mainly driven by substantial increases in the use of strong opioids (e.g., oxycodone). Indications and select data of NMPOU and PO-related morbidity and mortality have emerged in recent years, yet a systematic and comprehensive collection of relevant data to characterize the phenomenon in Canada does not exist. This paper comprehensively reviews the available data in Canada regarding NMPOU, and PO-related harms, diversion, and interventions, and discusses implications for interventions and policy. Narrative literature/data review. Canada. Publicly available data and information - either from journal publications, "grey literature" (e.g., government/technical reports) or Web sites reporting relevant data on Canada - were searched and narratively reviewed. Indicators on NMPOU and PO-related harms in Canada are highly fragmented, and not nearly as systematic and comprehensive as they are in the US; virtually no national statistics/data are collected. Available -largely provincial/local - data indicate that PO misuse is increasingly common in key populations, including general adult and student populations, street-drug users, First Nations/Aboriginal Peoples, and correctional populations. Co-morbidities - e.g., pain, mental health problems, polysubstance use - among people reporting NMPOU appear to be high. Substance use treatment admissions for those with problematic PO use have risen substantially where reported. Opioid-related mortality (and oxycodone-related mortality, specifically) have increased considerably in Ontario where relevant data from the mid-1990s onward have been examined. In Canadian populations reporting NMPOU, sourcing of POs occurs through various diversion routes, including from family/friends, "double-doctoring," or street drug markets. In addition, losses and theft/robberies from pharmacies and licensed medications dealers appear to be on the rise. Finally, interventions (i.e., provincial PO guidelines, prescription monitoring programs, substance use treatment services) are fragmented and inconsistently applied throughout the country, and currently fail to effectively address the growing problem of NMPOU and PO-related harms across Canada. This review did not rely on systematic review methodologies. Corresponding to its increasing and high overall PO consumption levels, NMPOU and PO-related harms in Canada are high based on available data, and likely now constitute the third highest level of substance use burden of disease (after alcohol and tobacco). The data and monitoring situation in Canada regarding NMPOU and PO-related harms are fragmented, un-systematic, and insufficient. While major and concerted policy initiatives - primarily from the federal level - are absent to date, these urgently require vastly improved national data indicators and monitoring in order to allow for and evaluate evidence-based interventions on this urgent and extensive public health problem.

Integrated Stewardship of NASA Satellite and Field Campaign Data

NASA Astrophysics Data System (ADS)

Hausman, J.; Tsontos, V. M.; Hardman, S. H.

2016-02-01

The Physical Oceanography Distributed Active Archive Center (PO.DAAC) is NASA's archive, steward and distributor for physical oceanographic satellite data. Those data are typically organized along the lines of single parameters, such as Sea Surface Temperature, Ocean Winds, Salinity, etc. However there is a need supplement satellite data with in situ and various other remote sensing data to provide higher spatial and temporal sampling and information on physical processes that the satellites are not capable of measuring. This presentation will discuss how PO.DAAC is creating a stewardship and distribution plan that will accommodate satellite, in situ and other remote sensing data that can be used to solve a more integrated approach to data access and utilization along thematic lines in support of science and applications, specifically those posed by Salinity Processes in the Upper Ocean Regional Study (SPURS) and Oceans Melting Greenland (OMG) projects. SPURS used shipboard data, moorings and in situ instruments to investigate changes in salinity and how that information can be used in explaining the water cycle. OMG is studying ice melt in Greenland and how it contributes to changes in sea level through shipboard measurements, airborne and a variety of in situ instruments. PO.DAAC plans on adapting to stewarding and distributing these varieties of data through applications of file format and metadata standards (so data are discoverable and interoperable), extend the internal data system (to allow for better archiving, collection generation and querying of in situ and airborne data) and integration into tools (visualization and data access). We are also working on Virtual Collections with ESDWG, which could provide access to relevant data across DAACs/Agencies along thematic lines. These improvements will improve long-term data management and make it easier for users of various background, regardless if remote sensing or in situ, to discover and use the data.

Report on the Global Data Assembly Center (GDAC) to the 12th GHRSST Science Team Meeting

NASA Technical Reports Server (NTRS)

Armstrong, Edward M.; Bingham, Andrew; Vazquez, Jorge; Thompson, Charles; Huang, Thomas; Finch, Chris

2011-01-01

In 2010/2011 the Global Data Assembly Center (GDAC) at NASA's Physical Oceanography Distributed Active Archive Center (PO.DAAC) continued its role as the primary clearinghouse and access node for operational Group for High Resolution Sea Surface Temperature (GHRSST) datastreams, as well as its collaborative role with the NOAA Long Term Stewardship and Reanalysis Facility (LTSRF) for archiving. Here we report on our data management activities and infrastructure improvements since the last science team meeting in June 2010.These include the implementation of all GHRSST datastreams in the new PO.DAAC Data Management and Archive System (DMAS) for more reliable and timely data access. GHRSST dataset metadata are now stored in a new database that has made the maintenance and quality improvement of metadata fields more straightforward. A content management system for a revised suite of PO.DAAC web pages allows dynamic access to a subset of these metadata fields for enhanced dataset description as well as discovery through a faceted search mechanism from the perspective of the user. From the discovery and metadata standpoint the GDAC has also implemented the NASA version of the OpenSearch protocol for searching for GHRSST granules and developed a web service to generate ISO 19115-2 compliant metadata records. Furthermore, the GDAC has continued to implement a new suite of tools and services for GHRSST datastreams including a Level 2 subsetter known as Dataminer, a revised POET Level 3/4 subsetter and visualization tool, a Google Earth interface to selected daily global Level 2 and Level 4 data, and experimented with a THREDDS catalog of GHRSST data collections. Finally we will summarize the expanding user and data statistics, and other metrics that we have collected over the last year demonstrating the broad user community and applications that the GHRSST project continues to serve via the GDAC distribution mechanisms. This report also serves by extension to summarize the activities of the GHRSST Data Assembly and Systems Technical Advisory Group (DAS-TAG).

Effect of different polishing systems on the surface roughness of nano-hybrid composites

PubMed Central

Patel, Brijesh; Chhabra, Naveen; Jain, Disha

2016-01-01

Objective: The study aimed to investigate the influence of different polishing systems on the surface roughness of nano-hybrid composite resins. Background: Different shapes of polishing systems are available according to the site of work. To minimize variability, a new system with single shape is developed that can be utilized in both anterior as well as posterior teeth. Materials and Methods: Seventy composite discs were fabricated using Teflon well (10 mm × 3 mm). Two main group of nano-hybrid composite Group I — Filtek Z350 and Group II — Tetric N-Ceram were used (n = 35 for each group). Both groups were further divided into four subgroups. Subgroup a — OneGloss (n = 10), Subgroup b - PoGo (n = 10), Subgroup c — Sof-Lex spiral (n = 10), Subgroup d - Mylar strip (control, n = 5). Samples were polished according to the manufacturer's recommendations. Surface roughness test was performed using contact profilometer. The obtained data were analyzed using the one-way analysis of variance test. Result: Tetric N-Ceram produced smoother surfaces than Filtek Z350 (P < 0.05). Mylar strip and “PoGo” created equally smooth surfaces, while significantly rougher surfaces were obtained after applications of “Sof-Lex spiral” and “OneGloss” (P < 0.05). Conclusion: Polishing ability of Tetric N-Ceram is better than Filtek Z350 XT. “PoGo” seems to be a better polishing system than “OneGloss” and “Sof-Lex Spiral.” PMID:26957791

Reproductive performance of peranakan ongole (PO) bull at different altitudes areas in Lampung province

NASA Astrophysics Data System (ADS)

Suretno, N. D.; Supriyatna, I.; Purwanto, B.; Priyanto, R.

2018-01-01

Peranakan Ongole (PO) cattle are famous for their bulls and known for their toughness, rapid growth and natural tolerance to tropical heat and disease resistance. This study was conducted to determine the reproductive performance of PO bull in some altitude in Lampung Province. A total of PO bulls used were 48 heads, with age three to four years. The variables observed were volume, consistency, pH, semen colour, concentration, mass movement, motility, percentage of living spermatozoa and abnormality. Data were collected during the rainy season and dry season, calculated with the average and standard deviation and then analyzed descriptively. Based on the macroscopic examination, Peranakan Ongole bull living in low temperature place had a normal semen volume, the consistency mostly watery to moderate, fresh semen pH is in the normal range and the color of semen are all normal both in the rainy and dry seasons. The results of microscopic examination showed that PO cattle had a good reproduction conditions at all three

Increase of 210Po levels in human semen fluid after mussel ingestion.

PubMed

Kelecom, Alphonse; Gouvea, Rita de Cássia dos Santos

2011-05-01

Polonium-210 ((210)Po) radioactive concentrations were determined in human semen fluid of vasectomized non-smoker volunteers. The (210)Po levels ranged from 0.10 to 0.39 mBq g(-1) (mean: 0.23 ± 0.08 mBq g(-1)). This value decreased to 0.10 ± 0.02 mBq g(-1) (range from 0.07 to 0.13 mBq g(-1)) after two weeks of a controlled diet, excluding fish and seafood. Then, volunteers ate during a single meal 200 g of the cooked mussel Perna perna L., and (210)Po levels were determined again, during ten days, in semen fluid samples collected every morning. Volunteers continued with the controlled diet and maintained sexual abstinence through the period of the experiment. A 300% increase of (210)Po level was observed the day following mussel consumption, with a later reduction, such that the level returned to near baseline by day 4. Copyright © 2011 Elsevier Ltd. All rights reserved.

The ratio of lead-210 to polonium-210 in U.K. diet.

PubMed

Smith-Briggs, J L; Bradley, E J; Potter, M D

1986-10-01

The levels of the natural radionuclides, 210Pb and 210Po, in U.K. diet have been measured previously. However, in the earlier measurements, the samples were sufficiently aged for 210Pb and 210Po to have attained secular equilibrium. In order to determine the extent of disequilibrium between these radionuclides in fresh food, measurements have been made on recently collected dietary samples. Disequilibrium has been observed in five food groups. The activity per unit mass of 210Pb was found to be greater than that of 210Po in bread, cereals, sugar and preserves, whereas the opposite was found to be true for eggs and beverages. When account is taken of consumption rates, however, the total intakes of 210Pb and 210Po from these food groups are approximately the same. The annual effective dose equivalents from the ingestion of 210Pb and 210Po have been re-estimated at 41 and 12 mu Sv, respectively.

In situ atomic force microscopy analysis of morphology and particle size changes in lithium iron phosphate cathode during discharge.

PubMed

Demirocak, Dervis Emre; Bhushan, Bharat

2014-06-01

Li-ion batteries offer great promise for future plug-in hybrid electric vehicles (PHEVs) and pure electric vehicles (EVs). One of the challenges is to improve the cycle life of Li-ion batteries which requires detailed understanding of the aging phenomenon. In situ techniques are especially valuable to understand aging since it allows monitoring the physical and chemical changes in real time. In this study, in situ atomic force microscopy (AFM) is utilized to study the changes in morphology and particle size of LiFePO4 cathode during discharge. The guidelines for in situ AFM cell design for accurate and reliable measurements based on different designs are presented. The effect of working electrode to counter electrode surface area ratio on cycling data of an in situ cell is also discussed. Analysis of the surface area change in LiFePO4 particles when the cell was cycled between 100% and 70% state of charge is presented. Among four particles analyzed, surface area increase of particles during Li intercalation of LiFePO4 spanned from 1.8% to 14.3% indicating the inhomogeneous nature of the cathode surface. Copyright © 2014 Elsevier Inc. All rights reserved.

An efficient hybrid technique in RCS predictions of complex targets at high frequencies

NASA Astrophysics Data System (ADS)

Algar, María-Jesús; Lozano, Lorena; Moreno, Javier; González, Iván; Cátedra, Felipe

2017-09-01

Most computer codes in Radar Cross Section (RCS) prediction use Physical Optics (PO) and Physical theory of Diffraction (PTD) combined with Geometrical Optics (GO) and Geometrical Theory of Diffraction (GTD). The latter approaches are computationally cheaper and much more accurate for curved surfaces, but not applicable for the computation of the RCS of all surfaces of a complex object due to the presence of caustic problems in the analysis of concave surfaces or flat surfaces in the far field. The main contribution of this paper is the development of a hybrid method based on a new combination of two asymptotic techniques: GTD and PO, considering the advantages and avoiding the disadvantages of each of them. A very efficient and accurate method to analyze the RCS of complex structures at high frequencies is obtained with the new combination. The proposed new method has been validated comparing RCS results obtained for some simple cases using the proposed approach and RCS using the rigorous technique of Method of Moments (MoM). Some complex cases have been examined at high frequencies contrasting the results with PO. This study shows the accuracy and the efficiency of the hybrid method and its suitability for the computation of the RCS at really large and complex targets at high frequencies.

Synthesis of carbon-coated Na2MnPO4F hollow spheres as a potential cathode material for Na-ion batteries

NASA Astrophysics Data System (ADS)

Wu, Ling; Hu, Yong; Zhang, Xiaoping; Liu, Jiequn; Zhu, Xing; Zhong, Shengkui

2018-01-01

Hollow sphere structure Na2MnPO4F/C composite is synthesized through spray drying, following in-situ pyrolytic carbon coating process. XRD results indicate that the well crystallized composite can be successfully synthesized, and no other impurity phases are detected. SEM and TEM results reveal that the Na2MnPO4F/C samples show intact hollow spherical architecture, and the hollow spherical shells with an average thickness of 150 nm-250 nm are composed of nanosized primary particles. Furthermore, the amorphous carbon layer is uniformly coated on the surface of the hollow sphere, and the nanosized Na2MnPO4F particles are well embedded in the carbon networks. Consequently, the hollow sphere structure Na2MnPO4F/C shows enhanced electrochemical performance. Especially, it is the first time that the obvious potential platforms (∼3.6 V) are observed during the charge and discharge process at room temperature.

Effect of organic additives on characteristics of carbon-coated LiCoPO4 synthesized by hydrothermal method

NASA Astrophysics Data System (ADS)

Maeyoshi, Yuta; Miyamoto, Shohei; Noda, Yusaku; Munakata, Hirokazu; Kanamura, Kiyoshi

2017-01-01

Carbon-coated LiCoPO4 particles are synthesized by one-pot hydrothermal process using three different organic additives (carboxymethylcellulose sodium salt (CMC), glucose, and ascorbic acid). The effect of the organic additives on particle size, morphology, nature of carbon coating, and electrochemical property of the resulting LiCoPO4 is investigated. CMC plays important roles to decrease the particle size and form well-covered carbon coating on the surface. Carbon-coated LiCoPO4 prepared using CMC delivers higher initial discharge capacity of 135 mA h g-1 at 0.1 C, and shows superior rate capability and cyclic performance than the other samples. The improved electrochemical characteristics are attributed to not only the fine particle which allows facile electronic and ionic transport, but also the high coverage of carbon coating which improves the electrical conductivity and prevents the irreversible reactions of the charged LiCoPO4 with electrolyte.

78 FR 24781 - 60-Day Notice of Proposed Information Collection: U.S. Passport Renewal Application for Eligible...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-26

..., Line 1: Replaced ``Street/RFD , P.O. Box, or URB'' with ``(Street/RFD , URB, or P.O. Box, Apt/Unit, In Care Of or Attn (e.g., In Care Of--Jane Doe, Apt 100))''. [cir] Mailing Address, Address Line 2... applicable. (e.g., In Care Of--Jane Doe, Apt 100)'' with ``(If applicable)''. In the photograph box, the...

Respiratory function of the plastron in the aquatic bug Aphelocheirus aestivalis (Hemiptera, Aphelocheiridae).

PubMed

Seymour, Roger S; Jones, Karl K; Hetz, Stefan K

2015-09-01

The river bug Aphelocheirus aestivalis is a 40 mg aquatic insect that, as an adult, relies totally on an incompressible physical gill to exchange respiratory gases with the water. The gill (called a 'plastron') consists of a stationary layer of air held in place on the body surface by millions of tiny hairs that support a permanent air-water interface, so that the insect never has to renew the gas at the water's surface. The volume of air in the plastron is extremely small (0.14 mm(3)), under slightly negative pressure and connected to the gas-filled tracheal system through spiracles on the cuticle. Here, we measure PO2 of the water and within the plastron gas with O2-sensing fibre optics to understand the effectiveness and limitations of the gas exchanger. The difference in PO2 is highest in stagnant water and decreases with increasing convection over the surface. Respiration of bugs in water-filled vials varies between 33 and 296 pmol O2 s(-1), depending on swimming activity. The effective thickness of the boundary layer around the plastron was calculated from respiration rate, PO2 difference and plastron surface area, according to the Fick diffusion equation and verified by direct measurements with the fibre-optic probes. In stagnant water, the boundary layer is approximately 500 μm thick, which nevertheless can satisfy the demands of resting bugs, even if the PO2 of the free water decreases to half that of air saturation. Active bugs require thinner boundary layers (∼ 100 μm), which are achieved by living in moving water or by swimming. © 2015. Published by The Company of Biologists Ltd.

Passivation process and the mechanism of packing particles in the Fe0/GAC system during the treatment of ABS resin wastewater.

PubMed

Lai, Bo; Zhou, Yuexi; Wang, Juling; Zhang, Yunhong; Chen, Zhiqiang

2014-01-01

This study provides mechanistic insights into the passivation of the packing particles during the treatment of acrylonitrile-butadiene-styrene (ABS) resin wastewater by the Fe0/GAC system. The granular-activated carbon (GAC) and iron chippings (Fe0) were mixed together with a volumetric ratio of 1:1. GAC has a mean particle size of approximately 3-5 mm, a specific surface of 748 m2 g(-1), a total pore volume of 0.48 mL g(-1) and a bulk density of 0.49 g cm(-3). The iron chippings have a compact and non-porous surface morphology. The results show that the packing particles in the Fe0/GAC system would lose their activity because the removal of TOC and PO4(3-) for ABS resin wastewater could not carried out by the Fe0/GAC system after 40 days continuous running. Meanwhile, the availability of O2 and intrinsic reactivity of Fe0 play a key role on the form of passive film with different iron oxidation states. The passive film on the surface of iron chippings was formed by two phases: (a) local corrosion phase (0-20 d) and (b) co-precipitation phase (20-40 d), while that of GAC was mainly formed by the co-precipitation of corrosion products with SO4(2-) and PO4(3-) because SO4(2-) and PO4(3-) would not easily reach the Fe0 surface. Therefore, in order to avoid the occurrence of filler passivation, high concentrations of SO4(2-) and PO4(3-) in wastewater should be removed before the treatment process of the Fe/GAC system.

The sorption and desorption of phosphate-P, ammonium-N and nitrate-N in cacao shell and corn cob biochars.

PubMed

Hale, S E; Alling, V; Martinsen, V; Mulder, J; Breedveld, G D; Cornelissen, G

2013-06-01

The sorption of PO4-P, NH4-N and NO3-N to cacao shell and corn cob biochars produced at 300-350°C was quantified. The biochars were used; (i) as received (unwashed), (ii) after rinsing with Millipore water and (iii) following leaching with Millipore water. In addition to sorption, desorption of PO4-P from the unwashed biochars was quantified. There was no sorption of PO4-P to either washed or rinsed biochars, but following leaching, both biochars adsorbed PO4-P and distribution coefficients (Kd L kg(-1)) were very similar for both materials (10(1.1±0.5) for cacao shell biochar and 10(1.0±0.2) for corn cob biochar). The BET surface area and micropore volume increased 80% and 60% for the cacao shell and corn cob biochars following leaching. After 60 d, 1483±45 mg kg(-1) and 172±1 mg kg(-1) PO4-P was released from the cacao shell and corn cob biochars. NH4-N was sorbed by both unwashed biochars, albeit weakly with Kd values around 10(2) L kg(-1). We speculate that NH4-N could bind via an electrostatic exchange with other cationic species on the surface of the biochar. There was no significant release or sorption of NO3-N from or to either of the biochars. Copyright © 2013 Elsevier Ltd. All rights reserved.

An impressive approach to solving the ongoing stability problems of LiCoPO4 cathode: Nickel oxide surface modification with excellent core-shell principle

NASA Astrophysics Data System (ADS)

Örnek, Ahmet

2017-07-01

Nanoscale and NiO-coated LiCoPO4 cathode materials were prepared for the first time by a newly designed three-step synthesis route, which is a combined technique including advantages of the Stöber, hydrothermal and microwave synthesis methods. Using this extraordinary technique, LiCoPO4 particles are coated with a thin NiO layer with a perfect core-shell morphology and the technique's positive contribution to electrochemistry is elucidated in detail. The samples are interpreted using opto-analytical techniques and galvanostatic charge-discharge tests. The high-resolution transmission electron microscopy analysis proves that this well-elaborated technique makes it possible to achieve a continuous NiO surface coverage of 8-10 nm, a result that contributes towards solving the chronic electrochemical problems of 4.8 V cathode material. Our data reveal that NiO-coated LiCoPO4 cathode demonstrates superior cycle stability and specific capacity at relatively low rates. The 2.5% wt. NiO-coated cathode exhibits the best electrochemical property, which reaches a discharge capacity of 159 mAh g-1 at 0.l C current rate and shows almost 85% capacity retention after 80 charge-discharge cycles. It therefore achieves partial success in improving the electrochemical properties of the LiCoPO4 cathode material, which is especially crucial for energy storage to be applied in electric vehicles and plug-in hybrid electric applications.

Tools for Scientist Engagement in E/PO: NASA SMD Community Workspace and Online Resources

NASA Astrophysics Data System (ADS)

Dalton, H.; Shipp, S. S.; Grier, J.; Gross, N. A.; Buxner, S.; Bartolone, L.; Peticolas, L. M.; Woroner, M.; Schwerin, T. G.

2014-12-01

The Science Mission Directorate (SMD) Science Education and Public Outreach (E/PO) Forums are here to help you get involved in E/PO! The Forums have been developing several online resources to support scientists who are - or who are interested in becoming - involved in E/PO. These include NASA Wavelength, EarthSpace, and the SMD E/PO online community workspace. NASA Wavelength is the one-stop shop of all peer-reviewed NASA education resources to find materials you - or your audiences - can use. Browse by audience (pre-K through 12, higher education, and informal education) or topic, or choose to search for something specific by keyword and audience. http://nasawavelength.org. EarthSpace, an online clearinghouse of Earth and space materials for use in the higher education classroom, is driven by a powerful search engine that allows you to browse the collection of resources by science topic, audience, type of material or key terms. All materials are peer-reviewed before posting, and because all submissions receive a digital object identifier (doi), submitted materials can be listed as publications. http://www.lpi.usra.edu/earthspace. The SMD E/PO online community workspace contains many resources for scientists. These include one-page guides on how to get involved, tips on how to make the most of your time spent on E/PO, and sample activities, as well as news on funding, policy, and what's happening in the E/PO community. The workspace also provides scientists and the public pathways to find opportunities for participation in E/PO, to learn about SMD E/PO projects and their impacts, to connect with SMD E/PO practitioners, and to explore resources to improve professional E/PO practice, including literature reviews, information about the Next Generation Science Standards, and best practices in evaluation and engaging diverse audiences. http://smdepo.org.

NASA's Science Education and Public Outreach Forums: Bringing Communities and Resources Together to Increase Effectiveness and Sustainability of E/PO

NASA Astrophysics Data System (ADS)

Sharma, Mangala; Smith, D.; Mendez, B.; Shipp, S.; Schwerin, T.; Stockman, S.; Cooper, L.

2010-03-01

The AAS-HEAD community has a rich history of involvement in education and public outreach (E/PO). HEAD members have been using NASA science and educational resources to engage and educate youth and adults nationwide in science, technology, engineering, and mathematics topics. Four new Science Education and Public Outreach Forums ("Forums") funded by NASA Science Mission Directorate (SMD) are working in partnership with the research and education community to ensure that current and future SMD-funded E/PO activities form a seamless whole, with easy entry points for scientists, engineers, faculty, students, K-12 formal and informal science educators, general public, and E/PO professionals alike. These Forums support the astrophysics, heliophysics, planetary and Earth science divisions of NASA SMD in three core areas: 1) E/PO community engagement and development to facilitate clear paths of involvement for scientists, engineers and others interested - or potentially interested - in participating in SMD-funded E/PO activities. Collaborations with science professionals are vital for infusing current, accurate SMD mission and research findings into educational products and activities. Forum activities will yield readily accessible information on effective E/PO strategies, resources, and expertise; context for individual E/PO activities; and opportunities for collaboration. 2) A rigorous analysis of SMD-funded E/PO products and activities to help understand how the existing collection supports education standards and audience needs and to identify areas of opportunity for new materials and activities. K-12 formal, informal, and higher education products and activities are included in this analysis. 3) Finally, to address E/PO-related systemic issues and coordinate related activities across the four SMD science divisions. By supporting the NASA E/PO community and facilitating coordination of E/PO activities within and across disciplines, the SMD-Forum partnerships will lead to more effective, sustainable, and efficient utilization of NASA science discoveries and learning experiences.

Ocean Surface Topography Data Products and Tools

NASA Technical Reports Server (NTRS)

Case, Kelley E.; Bingham, Andrew W.; Berwin, Robert W.; Rigor, Eric M.; Raskin, Robert G.

2004-01-01

The Physical Oceanography Distributed Active Archiving Center (PO.DAAC), NASA's primary data center for archiving and distributing oceanographic data, is supporting the Jason and TOPEX/Poseidon satellite tandem missions by providing a variety of data products, tools, and distribution methods to the wider scientific and general community. PO.DAAC has developed several new data products for sea level residual measurements, providing a longterm climate data record from 1992 to the present These products provide compatible measurements of sea level residuals for the entire time series including the tandem TOPEX/Poseidon and Jason mission. Several data distribution tool. are available from NASA PO.DAAC. The Near-Real-Time Image Distribution Server (NEREIDS) provides quicklook browse images and binary data files The PO.DAAC Ocean ESIP Tool (POET) provides interactive, on-tine data subsetting and visualization for several altimetry data products.

Polonium in cigarette smoke and radiation exposure of lungs

NASA Astrophysics Data System (ADS)

Carvalho, Fernando P.; Oliveira, João M.

2006-01-01

Polonium (210Po), the most volatile of naturally-occurring radionuclides in plants, was analysed in three common brands of cigarettes produced in Portugal. The analyses were carried out on the unburned tobacco contained in cigarettes, on the ashes and butts of smoked cigarettes and on the mainstream smoke. 210Po in tobacco displays concentrations ranging from 3 to 37 mBq g-1, depending upon the cigarette brand. The 210Po activity remaining in the solid residue of a smoked cigarette varied from 0.3 to 4.9 mBq per cigarette, and the 210Po in the inhaled smoke varied from 2.6 to 28.9 mBq. In all brands of cigarettes tested, a large fraction of the 210Po content is not inhaled by the smoker and it is released into the atmosphere. Part of it may be inhaled by passive smokers. Depending upon the commercial brand and upon the presence or absence of a filter in the cigarette, 5 to 37 % of the 210Po in the cigarette can be inhaled by the smoker. Taking into account the average 210Po in surface air, the smoker of one pack of twenty cigarettes per day may inhale 50 times 210Po than a non smoker. Cigarette smoke contributes with 1.5 % to the daily rate of 210Po absorption into the blood, 0.39 Bq d-1, and, after systemic circulation it gives rise to a whole body radiation dose in the same proportion. However, in the smoker the deposition of 210Po in the lungs is much more elevated than normal and may originate an enhanced radiation exposure. Estimated dose to the lungs is presented and radiobiological effects of cigarette smoke are discussed.

Carbon-Coated Current Collectors for High-Power Lithium-Ion Secondary Batteries

DTIC Science & Technology

2011-09-20

foils have been used as the current collectors for LiFePO4 and Li4Ti5O12. It was found that the C-coating has remarkably enhance the power performance...chemical vapor deposition (T-CVD) to produce surface C-coating, and the resulting foils were used as current collectors for LiFePO4 and Li4Ti5O12. The C...2 mm x 2 mm. Two types of active electrode materials have been used for test, and they are LiFePO4 (LFPO) and Li4Ti5O12 (LTO) as cathode and anode

Adsorption interaction in the molecular hydrogen-aluminophosphate AlPO-5 zeolite system

NASA Astrophysics Data System (ADS)

Grenev, I. V.; Gavrilov, V. Yu.

2015-03-01

The adsorption interaction between molecular hydrogen and atoms forming the lattice of AlPO-5 zeolite is studied. The potential of intramolecular interaction is calculated by summing the potentials of individual pairwise H2-O(Al, P) interactions in a fragment of the zeolite structure with a volume of ˜32 nm3. Isopotential surfaces are constructed that allow determination of the shape of zeolite microchannels and the places of the preferential localization of sorbate molecules in the porous space. The calculated and experimental values of the Henry constant of H2 adsorption on AlPO-5 at 77 K are compared.

Bioaccumulation of 210Po and 210Pb in cephalopods collected from Kudankulam (Southeastern coast of Gulf of Mannar, India) and assessment of dose in human beings.

PubMed

Khan, M Feroz; Wesley, S Godwin

2011-11-01

Activities of (210)Po and (210)Pb in various tissues of two common species of cephalopod molluscs (cuttlefishes) of Kudankulam coast were studied. Of all the tissues, (210)Po and (210)Pb were found accumulated more in the digestive gland, shell gland and intestine. Urotheuthis duvauceli accumulated more (210)Po and (210)Pb in certain organs when compared with Sepiella inermis. The activity ratio of (210)Po/(210)Pb fell within the range of 0.6-29.3 in the organs. The biological concentration factor for the organs ranged from 1.2×10(3) to 2×10(5) for (210)Po and 3.6×10(2) to 7.6×10(4) for (210)Pb. A significant variation in the accumulation of (210)Po and (210)Pb was noted between species, organs and seasons (p < 0.05). The whole-body internal dose rate due to (210)Po was 1.24 and 0.83 µGy h(-1) and it was 2×10(-3) and 3×10(-3) µGy h(-1) due to (210)Pb for both the species. The effective dose in humans due to (210)Po intake ranged from 96.3 to 376.6 µSv y(-1) and that of (210)Pb ranged from 35.2 to 105.7 µSv y(-1), respectively. The data generated will act as a reference database for these organisms of this coast in which a nuclear power station is under construction.

Raman intensity as a probe of concentration near a crystal growing in solution

NASA Technical Reports Server (NTRS)

Wilkinson, R. Allen

1989-01-01

The feasibility of using Raman spectral scattering signals for measurements of concentration profiles near a crystal interface during growth or dissolution is discussed. With KH2PO4 (KDP) as a test material, optical multichannel analyzer (OMA) detection of a solute Raman vibrational band provided direct quantification of solute concentration with band intensity. The intersection of incident laser and Raman collection optics provided 3-D selective point measurements of the solution concentration field. Unlike many other techniques, the Raman band intensity is not sensitive to the typical temperature variations. Precision calibration of Raman intensity versus KDP concentration with less than 1 pct standard deviation error levels was demonstrated. A fiber optic, which sampled incident laser intensity and coupled it to the OMA, provided a fully synchronized monitor of fluctuations in laser power to correlate with observed Raman signals. With 1 W of laser power at the sample, good data statistics required eight repeated data collections at approximately 2.5 min collection. The accumulated time represents the concentration measurement time at one spatial location. Photomicroscopy documented a 30 micrometer diameter by 200 micrometer of laser Raman scattering region in the solution near the crystal surface. The laser beam was able to approach up to 25 micrometer from the crystal surface. However, a crystal surface reflected intensity contribution was weakly detectable. Nucleated microcrystals were seen in the crystal-growing solution. These microcrystals convect right up to the crystal surface and indicate no quiet diffusion region under normal gravity conditions. Translation of the solution cell with respect to the optics caused systematic intensity errors.

Density functional theory study of lithium diffusion at the interface between olivine-type LiFePO4 and LiMnPO4

NASA Astrophysics Data System (ADS)

Shi, Jianjian; Wang, Zhiguo; Qing Fu, Yong

2016-12-01

Coating LiMnPO4 with a thin layer of LiFePO4 shows a better electrochemical performance than the pure LiFePO4 and LiMnPO4, thus it is critical to understand Li diffusion at their interfaces to improve the performance of electrode materials. Li diffusion at the (1 0 0)\\text{LiFeP{{\\text{O}}4}} //(1 0 0)\\text{LiMnP{{\\text{O}}4}} , (0 1 0)\\text{LiFeP{{\\text{O}}4}} //(0 1 0)\\text{LiMnP{{\\text{O}}4}} , and (0 0 1)\\text{LiFeP{{\\text{O}}4}} //(0 0 1)\\text{LiMnP{{\\text{O}}4}} interfaces between LiFePO4 and LiMnPO4 was investigated using density functional theory. The calculated diffusion energy barriers are 0.55 eV for Li to diffuse along the (0 0 1) interface, 0.44 and 0.49 eV for the Li diffusion inside the LiMnPO4 and along the (1 0 0) interface, respectively. When Li diffuses from the LiFePO4 to LiMnPO4 by passing through the (0 1 0) interfaces, the diffusion barriers are 0.45 and 0.60 eV for the Li diffusions in both sides. The diffusion barriers for Li to diffuse in LiMnPO4 near the interfaces decrease compared with those in the pure LiMnPO4. The calculated diffusion coefficient of Li along the (1 0 0) interface is in the range of 3.65  ×  10-11-5.28  ×  10-12 cm2 s-1, which is larger than that in the pure LiMnPO4 with a value of 7.5  ×  10-14 cm2 s-1. Therefore, the charging/discharging rate performance of the LiMnPO4 can be improved by surface coating with the LiFePO4.

Morphology-controlled synthesis of Ag{sub 3}PO{sub 4} nano/microcrystals and their antibacterial properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Aiping; Tian, Chungui, E-mail: tianchungui@yahoo.com.cn; Chang, Wei

Graphical abstract: The Ag{sub 3}PO{sub 4} with rhombic dodecahedral, spherical and small size particles were controllable fabricated just by changing the types of the solvent. The materials possess good antibacterial properties toward different kinds of bacteria. - Highlights: • The Ag{sub 3}PO{sub 4} with three morphologies were controllable fabricated. • The Ag{sub 3}PO{sub 4} as-prepared possess obvious antibacterial properties in the dark. • The antibacterial ability of Ag{sub 3}PO{sub 4} could be greatly improved under the visible light irradiation. - Abstract: We reported the controllable fabrication of Ag{sub 3}PO{sub 4} nano/microcrystals through a simple solution-based precipitation reaction. The samples weremore » characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy and infrared spectroscopy. The results indicated that the Ag{sub 3}PO{sub 4} crystals with three different morphology, including the rhombic dodecahedron of 500 nm, the sphere of 100 nm and the particles with small-size of 20 nm, could be obtained in the solvents of water, ethylene glycol (EG) and dimethyl sulfoxide (DMSO). The antibacterial assay showed that all samples possess obvious antibacterial properties. In addition, the Ag{sub 3}PO{sub 4} with small size of 20 nm showed better activity due to their high specific surface areas. Notably, we have found that the antibacterial ability of Ag{sub 3}PO{sub 4} could be greatly improved under the visible light irradiation, which are superior to that in the dark and commercial streptomycin.« less

Improved electrochemical performances of LiSn2(PO4)3 anode material for lithium-ion battery prepared by solid-state method

NASA Astrophysics Data System (ADS)

Naren; Tian, Jianhua; Wang, Dongdong; Shan, Zhongqiang

2017-09-01

The rhombohedral LiSn2(PO4)3 was prepared by solid-state method for the anode material of lithium-ion battery. The effect of pH value of hydrothermal reaction system on the morphology of SnO2 as the precursor of LiSn2(PO4)3 and the influence of heat-treatment procedure and conditions, such as the sintering temperature and time, on the property of LiSn2(PO4)3 were investigated. The purity, morphology, structure and size distribution of prepared LiSn2(PO4)3 were characterized respectively by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM) and scanning electron microscopy (SEM) methods. The results demonstrate that the as-prepared LiSn2(PO4)3 particles exhibit rhombohedral single-crystal structure with an average particle size of 200 nm. The electrochemical measurement results reveal that the as-prepared LiSn2(PO4)3/C electrode exhibits the improved cycling stability and reversibility with a reversible discharge capacity of 448.6 mA h g-1 at 100 mA g-1 and better rate capability of 332.6 mA h g-1 at 500 mA g-1. The charge-discharge mechanism of LiSn2(PO4)3/C electrode was also investigated. According to the test results of cyclic voltammetry, the electrode process includes not only the intercalation and deintercalation of lithium ions in the LiSn2(PO4)3 particles, but also the surface pseudo-capacitive effect.

Highly efficient photocatalytic degradation of methylene blue by PoPD/TiO2 nanocomposite

PubMed Central

Dong, Wenping; Cui, Guanwei; Ren, Zongming

2017-01-01

The poly-o-phenylenediamine (PoPD)/TiO2 nanocomposite was successfully synthesized via ‘in situ’ oxidative polymerization method. The modified photocatalysts were characterized by BET, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier-transform infrarad spectra (FT-IR), thermogravimrtic analysis (TGA), X-ray photoelectron spectroscopy (XPS), Ultraviolet-visible diffuse reflectance spectrum (UV-Vis DRS) and Photocurrent Test. The results showed that the PoPD exists on the surface of TiO2, the presence of PoPD does not impact on the lattice structure and grain size of TiO2, and the presence of PoPD enhances the visible response and photoelectric property. The photocatalytic degradation of methylene blue (MB) was chosen as a model reaction to evaluate the photocatalytic activities of TiO2 and PoPD/TiO2. The optimal preparation condition was the molar ratio of oPD to TiO2 = 3:1, HCl concentration = 1.2 mol/L, the molar ratio of APS to oPD = 1:1. The apparent first-order rate constant kapp of PoPD/TiO2 nanocomposite was 0.0098 min-1, which is 6 times higher than TiO2 (0.0016 min-1). Meanwhile, the PoPD/TiO2 nanocomposites showed excellent photocatalytic stability, and the photocatalytic stability was depended on the stability of structure. At last, the photocatalytic mechanism of POPD/TiO2 nanocomposites was also proposed based on the synergetic effect between TiO2 and PoPD. PMID:28329007

Effects of near-surface hydraulic gradients on nitrate and phosphorus losses in surface runoff.

PubMed

Zheng, Fen-Li; Huang, Chi-Hua; Norton, L Darrell

2004-01-01

Phosphorous (P) and nitrogen (N) in runoff from agricultural fields are key components of nonpoint-source pollution and can accelerate eutrophication of surface waters. A laboratory study was designed to evaluate effects of near-surface hydraulic gradients on P and N losses in surface runoff from soil pans at 5% slope under simulated rainfall. Experimental treatments included three rates of fertilizer input (control [no fertilizer input], low [40 kg P ha(-1), 100 kg N ha(-1)], and high [80 kg P ha(-1), 200 kg N ha(-1)]) and four near-surface hydraulic gradients (free drainage [FD], saturation [Sa], artesian seepage without rain [Sp], and artesian seepage with rain [Sp + R]). Simulated rainfall of 50 mm h(-1) was applied for 90 min. The results showed that near-surface hydraulic gradients have dramatic effects on NO(3)-N and PO(4)-P losses and runoff water quality. Under the low fertilizer treatment, the average concentrations in surface runoff from FD, Sa, Sp, and Sp + R were 0.08, 2.20, 529.5, and 71.8 mg L(-1) for NO(3)-N and 0.11, 0.54, 0.91, and 0.72 mg L(-1) for PO(4)-P, respectively. Similar trends were observed for the concentrations of NO(3)-N and PO(4)-P under the high fertilizer treatment. The total NO(3)-N loss under the FD treatment was only 0.01% of the applied nitrogen, while under the Sp and Sp + R treatments, the total NO(3)-N loss was 11 to 16% of the applied nitrogen. These results show that artesian seepage could make a significant contribution to water quality problems.

Polonium-210 in the environment around a radioactive waste disposal area and phosphate ore processing plant.

PubMed

Arthur, W J; Markham, O D

1984-04-01

Polonium-210 concentrations were determined for soil, vegetation and small mammal tissues collected at a solid radioactive waste disposal area, near a phosphate ore processing plant and at two rural areas in southeastern Idaho. Polonium concentrations in media sampled near the radioactive waste disposal facility were equal to or less than values from rural area samples, indicating that disposal of solid radioactive waste at the Idaho National Engineering Laboratory Site has not resulted in increased environmental levels of polonium. Concentrations of 210Po in soils, deer mice hide and carcass samples collected near the phosphate processing plant were statistically (P less than or equal to 0.05) greater than the other sampling locations; however, the mean 210Po concentration in soils and small mammal tissues from sampling areas near the phosphate plant were only four and three times greater, respectively, than control values. No statistical (P greater than 0.05) difference was observed for 210Po concentrations in vegetation among any of the sampling locations.

Use of long-lived radon daughters as indicators of exchange between the free troposphere and the marine boundary layer

NASA Technical Reports Server (NTRS)

Kritz, M. A.

1983-01-01

Fluxes and exchange coefficients are derived for the transport of Sr-90, Pb-210, Bi-210, and Po-210 between the free troposphere and the marine boundary layer and between the boundary layer and the sea surface. Radionuclide concentrations previously measured near Hawaii are used in the derivations. Values obtained for the free troposphere/boundary layer exchange coefficient (expressed as a piston velocity) were 185, 228 and 203 m/d for Pb-210, Bi-210, and Sr-90, respectively. The magnitude of the local sea-surface source of Po-210 is also determined.

Combined operando X-ray diffraction–electrochemical impedance spectroscopy detecting solid solution reactions of LiFePO4 in batteries

PubMed Central

Hess, Michael; Sasaki, Tsuyoshi; Villevieille, Claire; Novák, Petr

2015-01-01

Lithium-ion batteries are widely used for portable applications today; however, often suffer from limited recharge rates. One reason for such limitation can be a reduced active surface area during phase separation. Here we report a technique combining high-resolution operando synchrotron X-ray diffraction coupled with electrochemical impedance spectroscopy to directly track non-equilibrium intermediate phases in lithium-ion battery materials. LiFePO4, for example, is known to undergo phase separation when cycled under low-current-density conditions. However, operando X-ray diffraction under ultra-high-rate alternating current and direct current excitation reveal a continuous but current-dependent, solid solution reaction between LiFePO4 and FePO4 which is consistent with previous experiments and calculations. In addition, the formation of a preferred phase with a composition similar to the eutectoid composition, Li0.625FePO4, is evident. Even at a low rate of 0.1C, ∼20% of the X-ray diffractogram can be attributed to non-equilibrium phases, which changes our understanding of the intercalation dynamics in LiFePO4. PMID:26345306

Combined operando X-ray diffraction-electrochemical impedance spectroscopy detecting solid solution reactions of LiFePO4 in batteries.

PubMed

Hess, Michael; Sasaki, Tsuyoshi; Villevieille, Claire; Novák, Petr

2015-09-08

Lithium-ion batteries are widely used for portable applications today; however, often suffer from limited recharge rates. One reason for such limitation can be a reduced active surface area during phase separation. Here we report a technique combining high-resolution operando synchrotron X-ray diffraction coupled with electrochemical impedance spectroscopy to directly track non-equilibrium intermediate phases in lithium-ion battery materials. LiFePO4, for example, is known to undergo phase separation when cycled under low-current-density conditions. However, operando X-ray diffraction under ultra-high-rate alternating current and direct current excitation reveal a continuous but current-dependent, solid solution reaction between LiFePO4 and FePO4 which is consistent with previous experiments and calculations. In addition, the formation of a preferred phase with a composition similar to the eutectoid composition, Li0.625FePO4, is evident. Even at a low rate of 0.1C, ∼20% of the X-ray diffractogram can be attributed to non-equilibrium phases, which changes our understanding of the intercalation dynamics in LiFePO4.

Rapid Polyol-Assisted Microwave Synthesis of Nanocrystalline LiFePO4/C Cathode for Lithium-Ion Batteries.

PubMed

Paul, Baboo Joseph; Gim, Jihyeon; Baek, Sora; Kang, Jungwon; Song, Jinju; Kim, Sungjin; Kim, Jaekook

2015-08-01

Nanocrystalline LiFePO4/C has been synthesized under a very short period of time (90 sec) using a polyol-assisted microwave heating synthesis technique. The X-ray diffraction (XRD) data indicates that the rapidly synthesized materials correspond to phase pure olivine. Post-annealing of the as-prepared sample at 600 °C in argon atmosphere yields highly crystalline LiFePO4/C. The morphology of the samples studied using scanning electron microscopy (SEM) reveals the presence of secondary particles formed from aggregation of primary particles in the range of 30-50 nm. Transmission electron microscopy (TEM) images reveal a thin carbon layer coating on the surface of the primary particle. The charge/discharge studies indicate that the as-prepared and annealed LiFePO4/C samples delivered initial discharge capacities of 126 and 160 mA h g-1, respectively, with good capacity retentions at 0.05 mA cm-2 current densities. The post-annealing process indeed improves the crystallinity of the LiFePO4 nanocrystals, which enhances the electrode performance of LiFePO4/C.

Monodisperse porous LiFePO4/C microspheres derived by microwave-assisted hydrothermal process combined with carbothermal reduction for high power lithium-ion batteries

NASA Astrophysics Data System (ADS)

Chen, Rongrong; Wu, Yixiong; Kong, Xiang Yang

2014-07-01

A microwave-assisted hydrothermal approach combined with carbothermal reduction has been developed to synthesize monodisperse porous LiFePO4/C microspheres, which possess the diameter range of 1.0-1.5 μm, high tap density of ∼1.3 g cm-3, and mesoporous characteristic with Brunauer-Emmett-Teller (BET) surface area of 30.6 m2 g-1. The obtained microspheres show meatball-like morphology aggregated by the carbon-coated LiFePO4 nanoparticles. The electrochemical impedance spectra (EIS) results indicate that carbon coating can effectively enhance both of the electronic and ionic conductivities for LiFePO4/C microspheres. The Li-ion diffusion coefficient of the LiFePO4/C microspheres calculated from the cyclic voltammetry (CV) curves is ∼6.25 × 10-9 cm2 s-1. The electrochemical performance can achieve about 100 and 90 mAh g-1 at 5C and 10C charge/discharge rates, respectively. As cathode material, the as-prepared LiFePO4/C microspheres show excellent rate capability and cycle stability, promising for high power lithium-ion batteries.

Hydrophobic and Metallophobic Surfaces: Highly Stable Non-wetting Inorganic Surfaces Based on Lanthanum Phosphate Nanorods

PubMed Central

Sankar, Sasidharan; Nair, Balagopal N.; Suzuki, Takehiro; Anilkumar, Gopinathan M.; Padmanabhan, Moothetty; Hareesh, Unnikrishnan Nair S.; Warrier, Krishna G.

2016-01-01

Metal oxides, in general, are known to exhibit significant wettability towards water molecules because of the high feasibility of synergetic hydrogen-bonding interactions possible at the solid-water interface. Here we show that the nano sized phosphates of rare earth materials (Rare Earth Phosphates, REPs), LaPO4 in particular, exhibit without any chemical modification, unique combination of intrinsic properties including remarkable hydrophobicity that could be retained even after exposure to extreme temperatures and harsh hydrothermal conditions. Transparent nanocoatings of LaPO4 as well as mixture of other REPs on glass surfaces are shown to display notable hydrophobicity with water contact angle (WCA) value of 120° while sintered and polished monoliths manifested WCA greater than 105°. Significantly, these materials in the form of coatings and monoliths also exhibit complete non-wettability and inertness towards molten metals like Ag, Zn, and Al well above their melting points. These properties, coupled with their excellent chemical and thermal stability, ease of processing, machinability and their versatile photo-physical and emission properties, render LaPO4 and other REP ceramics utility in diverse applications. PMID:26955962

Embryonic integument and "molts" in Manduca sexta (Insecta, Lepidoptera).

PubMed

Ziese, Stefanie; Dorn, August

2003-02-01

In Manduca sexta the germ band is formed 12 h post-oviposition (p.o.) (=10% development completed) and is located above the yolk at the egg surface. The cells show a polar organization. They are engaged in the uptake and degradation of yolk globules, pinched off from the yolk cells. This process can be observed in the integumental cells during the first growth phase of the embryo that lasts until "katatrepsis," an embryonic movement that takes place at 40% development completed. At 37% development completed, the ectoderm deposits a thin membrane at its apical surface, the first embryonic membrane, which detaches immediately before katatrepsis. The second period of embryonic growth--from katatrepsis to 84 h p.o. (70% development completed)--starts with the deposition of a second embryonic membrane that is somewhat thicker than the first one and shows a trilaminar, cuticulin-like structure. Whereas the apical cell surface is largely smooth during the deposition of the first embryonic membrane, it forms microvilli during deposition of the second one. At the same time, uptake of formed yolk material ceases and the epidermal cells now contain clusters of mitochondria below the apical surface. Rough endoplasmic reticulum (RER) increases in the perinuclear region. The second embryonic membrane detaches about 63 h p.o. At 69 h p.o., a new generation of microvilli forms and islands of a typical cuticulin layer indicate the onset of the deposition of the larval cuticle. The third growth phase is characterized by a steady increase in the embryo length, the deposition of the larval procuticle, and by cuticular tanning at about 100 h p.o. Beginning at that stage, electron-lucent vesicles aggregate below the epidermal surface and are apparently released below the larval cuticle. Manduca sexta is the first holometabolous insect in which the deposition of embryonic membranes and cuticles has been examined by electron microscopy. In correspondence with hemimetabolous insects, the embryo of M. sexta secretes three covers at approximately the same developmental stage. A marked difference: the second embryonic cover, which in Hemimetabola clearly exhibits a cuticular organization, has instead a membranous, cuticulin-like structure. We see the difference as the result of an evolutionary reductional process promoted by the redundancy of embryonic covers in the egg shell. Embryonic "molts" also occur in noninsect arthropods; their phylogenetical aspects are discussed. Copyright 2002 Wiley-Liss, Inc.

Effect of carbonate and phosphate ratios on the transformation of calcium orthophosphates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eliassi, Mohammad Daoud, E-mail: eliassi2007@gmail.com; Zhao, Wei; Tan, Wen Feng, E-mail: wenfeng.tan@hotmail.com

2014-07-01

Graphical abstract: Complexes among phosphate, carbonate and calcium have been prepared via a facile hydrothermal route. The synthesized product at the low (0.15) and the high (1.8) molar ratio of PO{sub 4}{sup 3−}/CO{sub 3}{sup 2−} is calcium phosphate hydrate and hydroxylapatite (HAp), respectively. Molar ratios of PO{sub 4}{sup 3−}/CO{sub 3}{sup 2−} are effective on the reduction of carbonate activity during the crystallization of HAp. - Highlights: • Formation of different complexes from CO{sub 3}{sup 2−}, PO{sub 4}{sup 3−} and Ca{sup 2+} solutions at 60 °C. • Molar ratios of PO{sub 4}{sup 3−}/CO{sub 3}{sup 2} cause changes in phase and sizemore » of synthesized products. • Addition of PO{sub 4}{sup 3} inhibited the activity of CO{sub 3}{sup 2−} during bound with Ca{sup 2+}. • The phase transformation was completed, when CO{sub 3}{sup 2−} peaks disappeared in FTIR. • PO{sub 4}{sup 3−}, CO{sub 3}{sup 2−} and Ca{sup 2+} distributed heterogeneously on the surface of precipitation. - Abstract: Complexes among phosphate, carbonate and calcium have been synthesized by a designed hydrothermal method. Effects of carbonate and phosphate ratios on the transformation of calcium-orthophosphates were investigated. With X-ray diffraction measurement the synthesized product at the low (0.15) and the high (1.8) molar ratio of PO{sub 4}{sup 3−}/CO{sub 3}{sup 2−} is calcium phosphate hydrate at pH 9.0, and hydroxylapatite (HAp) at pH 8.0, respectively. Fourier transform infrared spectroscopy of product at the high ratio (1.8) of PO{sub 4}{sup 3−}/CO{sub 3}{sup 2−} shows that the CO{sub 3}{sup 2−} peaks disappear, and the strong peaks at 1412 and 1460 cm{sup −1} are assigned to the vibrations of PO{sub 4}{sup 3−} in HAp. {sup 31}P nuclear magnetic resonance spectra of products at the low (0.15–0.6) to the high (1.2–1.8) ratios of PO{sub 4}{sup 3−}/CO{sub 3}{sup 2−} are obtained at 2.9 and 2.7 ppm, respectively. Molar ratios of PO{sub 4}{sup 3−}/CO{sub 3}{sup 2−} are effective on the reduction of carbonate activity during the formation and infiltration events of calcium-phosphate surface precipitates, and are subsequently enclosed during HAp formation.« less

Beneficial use of meat and bone meal combustion residue: "an efficient low cost material to remove lead from aqueous effluent".

PubMed

Deydier, Eric; Guilet, Richard; Sharrock, Patrick

2003-07-04

Meat and bone meal (MBM) combustion residues, a natural apatite-rich substance, was evaluated as a low cost substitute for hydroxyapatite in lead sequestration from water effluents. The thermal behaviour of crude meat and bone meal was followed by TGA and 24% inorganic residue was collected. The resulting ashes were characterised by powder X-ray diffraction (XRD), particle size distribution, specific surface area (BET), and elemental analysis confirming apatite contents, with high level of phosphate (56.3%) and calcium (36.8%). Mechanism and kinetics of lead removal by this bioinorganic material were investigated and compared to mechanisms and kinetics involved with synthetic apatite. Batch metal removal experiments were carried out with 500 and 1500ppm (mg/kg) Pb(2+) solutions. Lead concentration, calcium and pH were monitored. We observed that the mechanism is similar to that occurring for pure apatite, and involved both surface complexation and calcium hydroyapatite (CaHA), Ca(10)(PO(4))(6)(OH)(2), dissolution followed by less soluble Pb(10)(PO(4))(6)(OH)(2) precipitation, as confirmed by XRD analysis of ashes after incubation with lead solution. Our results show that this natural apatite-rich material removes in a few minutes a large quantity of lead (275mg/g capacity) which remains however lower than the theoretical maximum capacity (if calcium were totally substituted by lead). Meat and bone meal combustion residues represent a valuable alternative apatite source for environmental application.

Residence times of surface water and particle-reactive 210Pb and 210Po in the East China and Yellow seas

NASA Astrophysics Data System (ADS)

Nozaki, Yoshiyuki; Tsubota, Hlroyuki; Kasemsupaya, Vimonrut; Yashima, Mayumi; Naoko, Ikuta

1991-05-01

228Ra, 226Ra, 210Pb, and 210Po were measured in the surface waters of the East China and Yellow seas. Using mass balance equations for the Ra isotopes, we estimated the total flux of diffusion from sediments and desorption from suspended particles to be 0.1 dpm 226Ra cm -2 a -1 and 1 dpm 228Ra cm -2 a -1, and residence times to be 2-3 years for the waters on the East China Sea Shelf and 5-6 years for Yellow Sea waters. Box-model calculations yielded generally congruent scavenging residence times for 210Pb and 210Po in the waters of ~2 months on the shelf and ~7 months in the Kuroshio Current. These suggest that reactive heavy metals and pollutants discharged through rivers from the continent to the East Asian continental shelf are largely deposited on the bottom sediments prior to transport to the pelagic ocean by lateral mixing.

Characterization of Phosphate Species on Hydrated Anatase TiO2 Surfaces.

PubMed

Tielens, Frederik; Gervais, Christel; Deroy, Geraldine; Jaber, Maguy; Stievano, Lorenzo; Coelho Diogo, Cristina; Lambert, Jean-François

2016-02-02

The adsorption/interaction of KH2PO4 with solvated (100) and (101) TiO2 anatase surfaces is investigated using periodic DFT calculations in combination with GIPAW NMR calculations and experimental IR and solid state (17)O, and (31)P NMR spectroscopies. A complete and realistic model has been used to simulate the solvent by individual water molecules. The most stable adsorption configurations are characterized theoretically at the atomic scale, and experimentally supported by NMR and IR spectroscopies. It is shown that H2PO4(-) chemisorbs on the (100) and (101) anatase surfaces, preferentially via a bidentate geometry. Dimer (H3P2O7(-)) and trimer (H4P3O10(-)) adsorption models are confronted with monomer adsorption models, in order to rationalize their occurrence.

Three-dimensional hollow graphene efficiently promotes electron transfer of Ag3PO4 for photocatalytically eliminating phenol

NASA Astrophysics Data System (ADS)

Song, Shaoqing; Meng, Aiyun; Jiang, Shujuan; Cheng, Bei

2018-06-01

The effective transport of photo-induced carriers over semiconductor photocatalyst is critical for enhancing the photocatalytic performance under light excitation. Although oxidized graphene (GO) and/or reduced graphene oxide (rGO) has been used as cocatalyst to promote the transfer and utilization of electrons, however, random diffusion and transfer of photo-induced charges are inevitable from all sides over these actual graphene owing to the limitation of the preparation process and theory. Herein, we utilized three-dimensional hollow carbon graphene (HCG) to promote the efficient electron transfer of Ag3PO4 in the photocatalytic process. Owing to the confinement-induced electron field of HCG, the constructed HCG-Ag3PO4 photocatalytic system demonstrated the enhanced visible-light adsorption, improved transfer of photo-induced charges, and suitable redox potentials as revealed by transient photo-current spectroscopic, surface photovoltage spectroscopy, and electron paramagnetic resonance (EPR). EPR spectra of oxygen species and gas chromatography-mass spectra exhibited high efficiency activity over HCG-Ag3PO4 with Z-scheme photocatalytic mechanism for phenol decomposition by reaction between hexanoic acid and radOH and radO2-. It is noteworthy that photocatalytic performance over optimal HCG-Ag3PO4 is 6, 3.43, 1.92 times of pristine Ag3PO4, GO-Ag3PO4, and rGO-Ag3PO4, respectively. The results may supply a novel perspective to enhance transfer of photo-induced charges for the promotion of photocatalytic technology.

On a framework for generating PoD curves assisted by numerical simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Subair, S. Mohamed, E-mail: prajagopal@iitm.ac.in; Agrawal, Shweta, E-mail: prajagopal@iitm.ac.in; Balasubramaniam, Krishnan, E-mail: prajagopal@iitm.ac.in

2015-03-31

The Probability of Detection (PoD) curve method has emerged as an important tool for the assessment of the performance of NDE techniques, a topic of particular interest to the nuclear industry where inspection qualification is very important. The conventional experimental means of generating PoD curves though, can be expensive, requiring large data sets (covering defects and test conditions), and equipment and operator time. Several methods of achieving faster estimates for PoD curves using physics-based modelling have been developed to address this problem. Numerical modelling techniques are also attractive, especially given the ever-increasing computational power available to scientists today. Here wemore » develop procedures for obtaining PoD curves, assisted by numerical simulation and based on Bayesian statistics. Numerical simulations are performed using Finite Element analysis for factors that are assumed to be independent, random and normally distributed. PoD curves so generated are compared with experiments on austenitic stainless steel (SS) plates with artificially created notches. We examine issues affecting the PoD curve generation process including codes, standards, distribution of defect parameters and the choice of the noise threshold. We also study the assumption of normal distribution for signal response parameters and consider strategies for dealing with data that may be more complex or sparse to justify this. These topics are addressed and illustrated through the example case of generation of PoD curves for pulse-echo ultrasonic inspection of vertical surface-breaking cracks in SS plates.« less

On a framework for generating PoD curves assisted by numerical simulations

NASA Astrophysics Data System (ADS)

Subair, S. Mohamed; Agrawal, Shweta; Balasubramaniam, Krishnan; Rajagopal, Prabhu; Kumar, Anish; Rao, Purnachandra B.; Tamanna, Jayakumar

2015-03-01

The Probability of Detection (PoD) curve method has emerged as an important tool for the assessment of the performance of NDE techniques, a topic of particular interest to the nuclear industry where inspection qualification is very important. The conventional experimental means of generating PoD curves though, can be expensive, requiring large data sets (covering defects and test conditions), and equipment and operator time. Several methods of achieving faster estimates for PoD curves using physics-based modelling have been developed to address this problem. Numerical modelling techniques are also attractive, especially given the ever-increasing computational power available to scientists today. Here we develop procedures for obtaining PoD curves, assisted by numerical simulation and based on Bayesian statistics. Numerical simulations are performed using Finite Element analysis for factors that are assumed to be independent, random and normally distributed. PoD curves so generated are compared with experiments on austenitic stainless steel (SS) plates with artificially created notches. We examine issues affecting the PoD curve generation process including codes, standards, distribution of defect parameters and the choice of the noise threshold. We also study the assumption of normal distribution for signal response parameters and consider strategies for dealing with data that may be more complex or sparse to justify this. These topics are addressed and illustrated through the example case of generation of PoD curves for pulse-echo ultrasonic inspection of vertical surface-breaking cracks in SS plates.

78 FR 25065 - Agency Information Collection Extension

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-29

... collection requests a three-year extension of Form FE-746R, ``Natural Gas Imports and Exports,'' OMB Control Number 1901-0294. The proposed collection will support DOE's Office of Fossil Energy (FE) in the.... Department of Energy, Office of Fossil Energy, Office of Natural Gas Regulatory Activities (FE-34), P.O. Box...

Estimation of land-surface evaporation at four forest sites across Japan with the new nonlinear complementary method.

PubMed

Ai, Zhipin; Wang, Qinxue; Yang, Yonghui; Manevski, Kiril; Zhao, Xin; Eer, Deni

2017-12-19

Evaporation from land surfaces is a critical component of the Earth water cycle and of water management strategies. The complementary method originally proposed by Bouchet, which describes a linear relation between actual evaporation (E), potential evaporation (E po ) and apparent potential evaporation (E pa ) based on routinely measured weather data, is one of the various methods for evaporation calculation. This study evaluated the reformulated version of the original method, as proposed by Brutsaert, for forest land cover in Japan. The new complementary method is nonlinear and based on boundary conditions with strictly physical considerations. The only unknown parameter (α e ) was for the first time determined for various forest covers located from north to south across Japan. The values of α e ranged from 0.94 to 1.10, with a mean value of 1.01. Furthermore, the calculated evaporation with the new method showed a good fit with the eddy-covariance measured values, with a determination coefficient of 0.78 and a mean bias of 4%. Evaluation results revealed that the new nonlinear complementary relation performs better than the original linear relation in describing the relationship between E/E pa and E po /E pa , and also in depicting the asymmetry variation between E pa /E po and E/E po .

Influence of five home whitening gels and a remineralizing gel on the enamel and dentin ultrastructure and hardness.

PubMed

Pinheiro, Helena Burlamaqui; Cardoso, Paulo Eduardo Capel

2011-06-01

To investigate the influence of calcium phosphate enhanced home whitening agents on human enamel and dentin surface microhardness and ultramorphology. Five intact molars crowns were used for ultrastructural analysis and five for microhardness test. Each resulting coronal structure was cut in slices. After measuring baseline Knoop Hardness Number (KHN) of the enamel and dentin, the slices were divided into six experimental groups and one control (n= 5). G1= 15% carbamide peroxide (CP); G2= 16% CP; G3= Ca and PO4 (remineralizing agent); G4= 16% CP with Ca and PO4; G5= 7.5% hydrogen peroxide (HP) with Ca and PO4; G6=7.5% HP with Ca. After each daily session of treatment, specimens were stored in distilled water (37 degrees C) until the next session. Products were applied for 2 weeks, according to manufacturers' instructions. Additional KHN weredetermined. Conventional whitening agents (G1; G2) and the gel with Ca (G6), caused KHN decrease (P< 0.05).The remineralizing and whitening agents with Ca and PO4 (G3; G4; G5) did not change KHN. A change of morphology was observed on enamel and dentin surfaces in G1; G2; G5.

Is the effect of person-organisation fit on turnover intention mediated by job satisfaction? A survey of community health workers in China.

PubMed

Zhang, Mingji; Yan, Fei; Wang, Wei; Li, Guohong

2017-02-22

Person-organisation fit (P-O fit) is a predictor of work attitude. However, in the area of human resource for health, the literature of P-O fit is quite limited. It is unclear whether P-O fit directly or indirectly affects turnover intention. This study aims to examine the mediation effect of job satisfaction on the relationship between P-O fit and turnover intention based on data from China. This is a cross-sectional survey of community health workers (CHWs) in China in 2013. A questionnaire of P-O fit, job satisfaction and turnover intention was developed, and its validity and reliability were assessed. Multiple regression and structural equation modelling were used to examine the relationship among P-O fit, job satisfaction and turnover intention. Multistage sampling was applied. In total, 656 valid questionnaire responses were collected from CHWs in four provincial regions in China, namely Shanghai, Shaanxi, Shandong and Anhui. P-O fit was directly related to job satisfaction (standardised β 0.246) and inversely related to turnover intention (standardised β -0.186). In the mediation model, the total effect of P-O fit on turnover intention was -0.186 (p<0.001); the direct effect of P-O fit on turnover intention was -0.094 (p<0.01); the indirect effect of job satisfaction on the relationship between P-O fit and turnover intention was -0.092 (p<0.001). The effect of P-O fit on turnover intention was partially mediated through job satisfaction. It is suggested that more work attitude variables and different dimensions of P-O fit be taken into account to examine the complete mechanism of person-organisation interaction. Indirect measures of P-O fit should be encouraged in practice to enhance work attitudes of health workers. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Self Service Fare Collection on Buses in Portland, OR

DOT National Transportation Integrated Search

1986-09-01

In 1980, the Urban Mass Transportation Administration (UMTA) awarded grants to the Tri-County Metropolitan Transportation District (TRI-MET) to implement self-service fare collection (SSFC) on its bus system. TRI-MET, the transit authority serving Po...

Improvement of the mechanical properties and corrosion resistance of biodegradable β-Ca3(PO4)2/Mg-Zn composites prepared by powder metallurgy: the adding β-Ca3(PO4)2, hot extrusion and aging treatment.

PubMed

Yan, Yang; Kang, Yijun; Li, Ding; Yu, Kun; Xiao, Tao; Deng, Youwen; Dai, Han; Dai, Yilong; Xiong, Hanqing; Fang, Hongjie

2017-05-01

In this study, 10%β-Ca 3 (PO 4 ) 2 /Mg-6%Zn (wt.%) composites with Mg-6%Zn alloy as control were prepared by powder metallurgy. After hot extrusion, the as-extruded composites were aged for 72h at 150°C. The effects of the adding β-Ca 3 (PO 4 ) 2 , hot extrusion and aging treatment on their microstructure, mechanical properties and corrosion resistance were investigated. The XRD results identified α-Mg, MgZn phase and β-Ca 3 (PO 4 ) 2 phase in these composites. After hot extrusion, grains were significantly refined, and the larger-sized β-Ca 3 (PO 4 ) 2 particles and coarse MgZn phases were broken into linear-distributed β-Ca 3 (PO 4 ) 2 and MgZn phases along the extrusion direction. After aging treatment, the elements of Zn, Ca, P and O presented a more homogeneous distribution. The compressive strengths of the β-Ca 3 (PO 4 ) 2 /Mg-Zn composites were approximately double those of natural bone, and their densities and elastic moduli matched those of natural bone. The immersion tests and electrochemical tests revealed that the adding β-Ca 3 (PO 4 ) 2 , hot extrusion and aging treatment could promote the formation of protective corrosion product layer on the sample surface in Ringer's solution, which improved corrosion resistance of the β-Ca 3 (PO 4 ) 2 /Mg-Zn composites. The XRD results indicated that the corrosion product layer contained Mg(OH) 2 , β-Ca 3 (PO 4 ) 2 and hydroxyapatite (HA). The cytotoxicity assessments showed the as-extruded β-Ca 3 (PO 4 ) 2 /Mg-Zn composite aged for 72h was harmless to L-929 cells. These results suggested that the β-Ca 3 (PO 4 ) 2 /Mg-Zn composites prepared by powder metallurgy were promising to be used for bone tissue engineering. Copyright © 2017 Elsevier B.V. All rights reserved.

Impact of partial pressure of oxygen in blood samples on the performance of systems for self-monitoring of blood glucose.

PubMed

Schmid, Christina; Baumstark, Annette; Pleus, Stefan; Haug, Cornelia; Tesar, Martina; Freckmann, Guido

2014-03-01

The partial pressure of oxygen (pO2) in blood samples can affect glucose measurements with oxygen-sensitive systems. In this study, we assessed the influence of different pO2 levels on blood glucose (BG) measurements with five glucose oxidase (GOD) systems and one glucose dehydrogenase (GDH) system. All selected GOD systems were indicated by the manufacturers to be sensitive to increased oxygen content of the blood sample. Venous blood samples of 16 subjects (eight women, eight men; mean age, 52 years; three with type 1 diabetes, four with type 2 diabetes, and nine without diabetes) were collected. Aliquots of each sample were adjusted to the following pO2 values: ≤45 mm Hg, approximately 70 mm Hg, and ≥150 mm Hg. For each system, five consecutive measurements on each sample were performed using the same test strip lot. Relative differences between the mean BG value at a pO2 level of approximately 70 mm Hg, which was considered to be similar to pO2 values in capillary blood samples, and the mean BG value at pO2 levels ≤45 mm Hg and ≥150 mm Hg were calculated. The GOD systems showed mean relative differences between 11.8% and 44.5% at pO2 values ≤45 mm Hg and between -14.6% and -21.2% at pO2 values ≥150 mm Hg. For the GDH system, the mean relative differences were -0.3% and -0.2% at pO2 values ≤45 mm Hg and ≥150 mm Hg, respectively. The magnitude of the pO2 impact on BG measurements seems to vary among the tested oxygen-sensitive GOD systems. The pO2 range in which oxygen-sensitive systems operate well should be provided in the product information.

Changes in the composition of organic matter from prodeltaic sediments after a large flood event (Po River, Italy)

NASA Astrophysics Data System (ADS)

Tesi, T.; Langone, L.; Goñi, M. A.; Miserocchi, S.; Bertasi, F.

2008-04-01

The Po River (Italy) experienced a 100-year flood in October 2000. Surface sediments (0-1 cm) from cross-shelf transects were collected in the Po prodelta area (Adriatic Sea) in December 2000, in order to describe the distribution of organic matter (OM) along the main sediment dispersal system immediately after the flood event. Stations were subsequently reoccupied in October 2001 and April 2002. This sampling program provided a special opportunity to characterize the initial surficial flood deposit and the evolution of its associated OM over the course of 2 years. CuO oxidation, elemental, δ 13C, Δ 14C, and grain-size analyses were carried out to characterize the source, age, and spatial variability of sedimentary OM. Statistical analysis (PERMANOVA) was then applied to investigate temporal changes in different portions of the Po prodelta area. Isotopic and biomarker data suggest that the sedimentary OM in the flood deposit was initially dominated by aged (Δ 14C Dec-00 = -298.7 ± 56.3‰), lignin-poor OM (Λ Dec-00 = 1.96 ± 0.33 mg/100 mg OC), adsorbed on the fine material (clay Dec-00 = 72.1 ± 4.8%) delivered by the flood. In the 2 years following the flood, post-depositional processes significantly increased the content of lignin (Λ Oct-01 = 2.19 ± 0.51 mg/100 mg OC; Λ Apr-02 = 2.61 ± 0.63 mg/100 mg OC); and coarse material (silt and sand), while decreasing the contributions from aged OC (Δ 14C Oct-01 = -255.7 ± 32.8‰; Δ 14C Apr-02 = -213.2 ± 30.4‰) and fine fraction (clay Oct-01 = 54.8 ± 9.5%; clay Apr-02 = 44.6 ± 13.3%). The major changes were observed in the northern and central portions of the prodelta.

Hydrogeochemistry and water quality of the Kordkandi-Duzduzan plain, NW Iran: application of multivariate statistical analysis and PoS index.

PubMed

Soltani, Shahla; Asghari Moghaddam, Asghar; Barzegar, Rahim; Kazemian, Naeimeh; Tziritis, Evangelos

2017-08-18

Kordkandi-Duzduzan plain is one of the fertile plains of East Azarbaijan Province, NW of Iran. Groundwater is an important resource for drinking and agricultural purposes due to the lack of surface water resources in the region. The main objectives of the present study are to identify the hydrogeochemical processes and the potential sources of major, minor, and trace metals and metalloids such as Cr, Mn, Cd, Fe, Al, and As by using joint hydrogeochemical techniques and multivariate statistical analysis and to evaluate groundwater quality deterioration with the use of PoS environmental index. To achieve these objectives, 23 groundwater samples were collected in September 2015. Piper diagram shows that the mixed Ca-Mg-Cl is the dominant groundwater type, and some of the samples have Ca-HCO 3 , Ca-Cl, and Na-Cl types. Multivariate statistical analyses indicate that weathering and dissolution of different rocks and minerals, e.g., silicates, gypsum, and halite, ion exchange, and agricultural activities influence the hydrogeochemistry of the study area. The cluster analysis divides the samples into two distinct clusters which are completely different in EC (and its dependent variables such as Na + , K + , Ca 2+ , Mg 2+ , SO 4 2- , and Cl - ), Cd, and Cr variables according to the ANOVA statistical test. Based on the median values, the concentrations of pH, NO 3 - , SiO 2 , and As in cluster 1 are elevated compared with those of cluster 2, while their maximum values occur in cluster 2. According to the PoS index, the dominant parameter that controls quality deterioration is As, with 60% of contribution. Samples of lowest PoS values are located in the southern and northern parts (recharge area) while samples of the highest values are located in the discharge area and the eastern part.

Accumulation of polonium 210Po in tissues and organs of deer carvidae from Northern Poland.

PubMed

Skwarzec, Bogdan; Prucnal, Malgorzata

2007-01-01

This study was undertaken to provide information on accumulation of polonium in tissues and organs of deer carvidae in order to assess the potential transport of this element via food-chain to game meat consumers. Livers, kidneys and muscles of large herbivorous animals belonging to three species: roe deer (Capreolus capreolus), red deer (Cervus elaphus) and fallow deer (Dama dama), collected in Northern Poland, were the subject of the present investigation. Activities of (210)Po were determined by means of alpha spectrometry along with relevant radiochemical procedures. The concentration of (210)Po in analyzed animals decreased in the order kidney > liver > muscle tissue. The average activity concentrations of (210)Po ranged between 0.02 +/- 0.01 Bq. kg(- 1) w.w. in muscles and 7.15 +/- 0.12 Bq. kg(- 1) w.w. in kidneys. Levels of polonium were not influenced by sampling location, sex, age and species of animals.

DFT computational study on the phosphate functionalized SWCNTs as efficient drug delivery systems for anti-osteoporosis zolendronate and risedronate drugs

NASA Astrophysics Data System (ADS)

Nikfar, Zahra; Shariatinia, Zahra

2017-07-01

The pristine (4,4)-armchair SWCNT as well as its three phosphate functionalized (CNT-nH2PO4, n=1-3) forms were studied as novel drug delivery systems for the two commercially famous anti-osteoporosis drugs including risedronate (RIS) and zolendronate (ZOL) using the density functional theory (DFT) computations at both B3LYP and B3PW91 levels. Results revealed that the binding energy was increased by increasing number of H2PO4 moieties attached on the CNT with the most negative binding energy was measured for the CNT-3H2PO4 carrier. The dipole moments of all phosphate containing CNTs were much greater ( 1.5-4.5 D) than that of pristine CNT ( 0 D). The contour maps verified that when the CNT was functionalized by H2PO4 groups, the symmetric distribution of electric charge was vanished so that the highest and the lowest asymmetric charge distributions were achieved for the CNT-2H2PO4 and CNT-3H2PO4, respectively, leading to the greatest and the smallest dipole moments for the CNT-2H2PO4 (4.177 D) and the CNT-3H2PO4 (1.614 D). The compounds RIS-CNT-3H2PO4 and ZOL-CNT-3H2PO4 displayed the greatest electronegativity and electrophilicity index which were appropriate for the binding of drugs onto the bone surface (having partial positive charge due to the presence of Ca2+) and therefore effectively inhibiting the osteoporosis. Consequently, it was proposed that the drug-CNT-3H2PO4 was the most appropriate drug-carrier system for both of the RIS and ZOL drugs which could be employed as the most efficient vehicle.

Water and oil wettability of anodized 6016 aluminum alloy surface

NASA Astrophysics Data System (ADS)

Rodrigues, S. P.; Alves, C. F. Almeida; Cavaleiro, A.; Carvalho, S.

2017-11-01

This paper reports on the control of wettability behaviour of a 6000 series aluminum (Al) alloy surface (Al6016-T4), which is widely used in the automotive and aerospace industries. In order to induce the surface micro-nanostructuring of the surface, a combination of prior mechanical polishing steps followed by anodization process with different conditions was used. The surface polishing with sandpaper grit size 1000 promoted aligned grooves on the surface leading to static water contact angle (WCA) of 91° and oil (α-bromonaphthalene) contact angle (OCA) of 32°, indicating a slightly hydrophobic and oleophilic character. H2SO4 and H3PO4 acid electrolytes were used to grow aluminum oxide layers (Al2O3) by anodization, working at 15 V/18° C and 100 V/0 °C, respectively, in one or two-steps configuration. Overall, the anodization results showed that the structured Al surfaces were hydrophilic and oleophilic-like with both WCA and OCA below 90°. The one-step configuration led to a dimple-shaped Al alloy surface with small diameter of around 31 nm, in case of H2SO4, and with larger diameters of around 223 nm in case of H3PO4. The larger dimples achieved with H3PO4 electrolyte allowed to reach a slight hydrophobic surface. The thicker porous Al oxide layers, produced by anodization in two-step configuration, revealed that the liquids can penetrate easily inside the non-ordered porous structures and, thus, the surface wettability tended to superhydrophilic and superoleophilic character (CA < 10°). These results indicate that the capillary-pressure balance model, described for wettability mechanisms of porous structures, was broken. Moreover, thicker oxide layers with narrow pores of about 29 nm diameter allowed to achieve WCA < OCA. This inversion in favour of the hydrophilic-oleophobic surface behaviour is of great interest either for lubrication of mechanical components or in water-oil separation process.

Surface modification of titania powder P25 with phosphate and phosphonic acids--effect on thermal stability and photocatalytic activity.

PubMed

Djafer, Lahcène; Ayral, André; Boury, Bruno; Laine, Richard M

2013-03-01

Phosphorus is frequently reported as a doping element for TiO(2) as photocatalyst; however, the previously reported methods used to prepare P-doped TiO(2) do not allow control over the location of the phosphorus either in the bulk or at the surface or both. In this study, we report on the surface modification of Evonik P25 with phosphonic (H(3)PO(3)) and octylphosphonic acid [C(8)H(17)-PO(OH)(2)], done to limit the introduction of phosphorus only to the photocatalyst surface. The effect of this element on the thermal behavior and photocatalytic properties is reported through characterization using elemental analyses, solid state (31)P NMR, X-ray powder diffraction, N(2) porosimetry, dilatometry, etc. Thus, the objective of the work reported here is to focus on the role(s) that phosphorus plays only at TiO(2) crystallite surfaces. For comparison, other samples were treated with phosphoric acid. Copyright © 2012 Elsevier Inc. All rights reserved.

Assessment of Committed Effective Dose due to consumption of Red Sea coral reef fishes collected from the local market (Sudan).

PubMed

Hassona, Rifaat K; Sam, A K; Osman, O I; Sirelkhatim, D A; LaRosa, J

2008-04-15

An assessment of Committed Effective Dose (CED) due to consumption of Red Sea fish containing (210)Po and (137)Cs was performed for 23 different marine fish samples collected from the local market at Port Sudan. The fish were classified according to their feeding habits into three categories: carnivores, herbivores, and omnivores. Measured activity concentrations of (210)Po were found in the ranges 0.25-6.42 (carnivores), 0.7-5 (omnivores) and 1.5-3.8 (herbivores) Bq/kg fresh weight. In the same study, activity concentrations of Cs-137 were determined to be in the ranges 0.1-0.46 (carnivores), 0.09-0.35 (omnivores) and 0.09-0.32 (herbivores) Bq/kg fresh weight, which were several times lower than those of (210)Po. Appropriate conversion factors were used to derive the CED, which was found to be 0.012, 0.01 and 0.01 (microSv/yr) in carnivores, omnivores and herbivores, respectively, for (137)Cs. This contributes about 0.4% of the total dose exclusively by ingestion of fish. For (210)Po, it was found to be 3.47, 4.81 and 4.14 (microSv/yr) in carnivores, omnivores and herbivores, respectively, which represents 99.6% of the total dose (exclusively by ingestion of fish). The results of CED calculations suggest that the dose received by the Sudanese population from the consumption of marine fish is rather small and that the contribution of (137)Cs is negligible compared to (210)Po.

Spectroscopic and Electrochemical Properties of Lithium-Rich LiFePO4 Cathode Synthesized by Solid-State Reaction

NASA Astrophysics Data System (ADS)

Rosaiah, P.; Hussain, O. M.; Zhu, Jinghui; Qiu, Yejun

2017-08-01

Lithium iron phosphate (Li x FePO4) is synthesized by a solid-state reaction method. The structural, electrical and electrochemical properties are studied in detail. It is found that the increment of lithium concentration (up to x = 1.05) does not affect the structure of LiFePO4 but improves its electrical conductivity as well as electrochemical performance. Surface morphological studies exhibited the formation of rod-like nanoparticles with small size. Electric and dielectric properties are also investigated over a frequency range of 1 Hz-1 MHz at different temperatures. The conductivity increased with increasing temperature, which follows the Arrhenius relation with the activation energy of about 0.31 eV. And the electrochemical tests found that the Li1.05FePO4 cathode possessed improved discharge capacity with better cycling performance.

Phosphate and phytate adsorption and precipitation on ferrihydrite surfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xiaoming; Hu, Yongfeng; Tang, Yadong

Phosphorous (P) sorption on mineral surfaces largely controls P mobility and bioavailability, hence its pollution potential, but the sorption speciation and mechanism remain poorly understood. In this study, we have identified and quantified the speciation of both phosphate and phytate sorbed on ferrihydrite with various P loadings at pH 3–8 using differential atomic pair distribution function (d-PDF) analysis, synchrotron-based X-ray diffraction (XRD), and P and Fe K-edge X-ray absorption near edge structure (XANES) and attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy. With increasing P sorption loading for both phosphate and phytate, the sorption mechanism transits from bidentate-binuclear surface complexation tomore » unidentified ternary complexation and to precipitation of amorphous FePO 4 and amorphous Fe-phytate. At a given P sorption loading, phosphate precipitates more readily than phytate. Both phosphate and phytate promote ferrihydrite dissolution with phytate more intensively, but the dissolved FeIII concentration in the bulk solution is low because the majority of the released Fe III precipitate with the anions. Results also show that amorphous FePO 4 and amorphous Fe-phytate have similar PO 4 local coordination environment. In conclusion, these new insights into the P surface complexation and precipitation, and the ligand-promoted dissolution behavior improve our understanding of P fate in soils, aquatic environment and water treatment systems as mediated by mineral-water interfacial reactions.« less

Phosphate and phytate adsorption and precipitation on ferrihydrite surfaces

DOE PAGES

Wang, Xiaoming; Hu, Yongfeng; Tang, Yadong; ...

2017-09-26

Phosphorous (P) sorption on mineral surfaces largely controls P mobility and bioavailability, hence its pollution potential, but the sorption speciation and mechanism remain poorly understood. In this study, we have identified and quantified the speciation of both phosphate and phytate sorbed on ferrihydrite with various P loadings at pH 3–8 using differential atomic pair distribution function (d-PDF) analysis, synchrotron-based X-ray diffraction (XRD), and P and Fe K-edge X-ray absorption near edge structure (XANES) and attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy. With increasing P sorption loading for both phosphate and phytate, the sorption mechanism transits from bidentate-binuclear surface complexation tomore » unidentified ternary complexation and to precipitation of amorphous FePO 4 and amorphous Fe-phytate. At a given P sorption loading, phosphate precipitates more readily than phytate. Both phosphate and phytate promote ferrihydrite dissolution with phytate more intensively, but the dissolved FeIII concentration in the bulk solution is low because the majority of the released Fe III precipitate with the anions. Results also show that amorphous FePO 4 and amorphous Fe-phytate have similar PO 4 local coordination environment. In conclusion, these new insights into the P surface complexation and precipitation, and the ligand-promoted dissolution behavior improve our understanding of P fate in soils, aquatic environment and water treatment systems as mediated by mineral-water interfacial reactions.« less

Advanced Nanofiber-Based Lithium-Ion Battery Cathodes

NASA Astrophysics Data System (ADS)

Toprakci, Ozan

Among various energy storage technologies, rechargeable lithium-ion batteries have been considered as effective solution to the increasing need for high-energy density electrochemical power sources. Rechargeable lithium-ion batteries offer energy densities 2 - 3 times and power densities 5 - 6 times higher than conventional Ni-Cd and Ni-MH batteries, and as a result, they weigh less and take less space for a given energy delivery. However, the use of lithium-ion batteries in many large applications such as electric vehicles and storage devices for future power grids is hindered by the poor thermal stability, relatively high toxicity, and high cost of lithium cobalt oxide (LiCoO2) powders, which are currently used as the cathode material in commercial lithium-ion batteries. Recently, lithium iron phosphate (LiFePO 4) powders have become a favorable cathode material for lithium-ion batteries because of their low cost, high discharge potential (around 3.4 V versus Li/Li+), large specific capacity (170 mAh g -1), good thermal stability, and high abundance with the environmentally benign and safe nature. As a result, there is a huge demand for the production of high-performance LiFePO4. However, LiFePO4 also has its own limitation such as low conductivity (˜10-9 S cm -1), which results in poor rate capability. To address this problem, various approaches can be used such as decreasing particle size of LiFePO 4, doping LiFePO4 with metal ions or coating LiFePO 4 surface with carboneous materials. Formation of conductive layer on LiFePO4 and decreasing particle size are promising approaches due to their superior contribution to electrical conductivity and electrochemical performance of LiFePO4. Although different approaches can be used for surface coating and particle size decrement, electrospinning can be potentially considered as an efficient, simple and inexpensive way. In this study, LiFePO 4/carbon and carbon nanotube- and graphene-loaded electrospun LiFePO 4/carbon composite nanofibers were synthesized by using a combination of sol-gel and electrospinning. During the material preparation, polyacrylonitrile (PAN) was used as an electrospinning media and a carbon source. LiFePO 4 precursor materials and/or conductive materials (carbon nanotubes and graphene) and PAN were dissolved in N,N-dimethylformamide separately and they were mixed before electrospinning. LiFePO4 precursor/PAN fibers were heat treated, during which LiFePO4 precursor transformed to energy-storage LiFePO4 material and PAN was converted to carbon. The surface morphology, microstructure and electrochemical performance of the materials were analyzed. Compared with conventional powder based positive electrodes, the novel LiFePO4/C composite nanofiber cathodes possess better electrochemical performance. Furthermore, the newly developed LiFePO 4/C composite nanofibers are easy to fabricate, highly controllable, and can be used in practical Lithium-ion battery applications. In addition to LiFePO4, more recent efforts have been directed to mixed form of layered lithiummetal oxides (Li-Ni-Mn-Co). Nickel and manganese are of importance because of their lower cost, safety and higher abundance in nature. These new cathodes offer noticeable improvement in the capacity and cycling behavior. In these cathodes, LiNi1/3Co1/3Mn 1/3O2 attracted significant interest because of its good electrochemical properties such as high capacity, prolonged cycling life, and so on. On the other hand, it has some disadvantages such as instability at high voltages and high current densities. To overcome these problems, synthesis of layered Li-rich composite materials such as xLi2MnO3˙(1-x)LiCo 1/3Ni1/3Mn1/3O2 can be a promising approach. In this study, various xLi2MnO3˙(1-x)LiCo 1/3Ni1/3Mn1/3O2 (x=0.1, 0.2, 0.3, 0.4, 0.5) composite cathode materials were prepared by a one-step sol-gel route. Morphology, microstructure and electrochemical behavior of these cathode materials were evaluated. The resultant cathode material shows good electrochemical performance. Relatively low cost and simple preparation route make new xLi2MnO3˙(1-x)LiMn1/3Ni 1/3Co1/3O2 composite materials possible to use as potential cathode candidate for lithium-ion batteries.

Evaluation of the contribution of smoking to total blood polonium-210 in Saudi population.

PubMed

Shabana, E I; Abd Elaziz, M A; Al-Arifi, M N; Al-Dhawailie, A A; Al-Bokari, M M

2000-01-01

A preliminary study of 210Po concentrations in the blood of some smokers and nonsmokers is presented in order to evaluate the contribution of smoking to total blood 210Po in Saudi population. Blood samples were collected from 30 volunteers and analyzed by high resolution alpha-spectrometry using a radiochemical technique. The technique is based on the separation of polonium from other components of the sample by wet ashing with an HNO3/H2O2 oxidizing mixture and spontaneous deposition on a silver disc under the relevant conditions for alpha-particle counting. The results indicated that a significant fraction (about 30%) of blood 210Po is related to smoking.

A novel second-generation polyolefin container for storage of single-donor apheresis platelets.

PubMed

Shimizu, T; Kouketsu, K; Kamiya, T; Futagawa, H; Hirose, S

1989-01-01

A non-blow-molded LE-2 polyolefin (PO) container was developed to store single-donor apheresis platelet concentrates (PCs) processed by the Haemonetics Plasma Collecting System (PCS) at 22 degrees C for over 1 day. We molded PO containers with heat-sealing of light-weight polymer alloy films with a thickness of 0.25 mm. The film was made of polymer blends consisting of polypropylene, styrene ethylene butylene styrene-block copolymer, and ethylene ethylacrylate copolymer. The PO container with enough strength and flexibility in routine practice has 2 and 1.6 times higher oxygen and carbon dioxide gas transfer properties than standard polyvinyl chloride (PVC) plastic containers. PCs (1-1.9 x 10(11) platelets) processed from 450 ml platelet-rich plasma were stored in 0.6-liter PO containers at 22 degrees C with flatbed agitation for up to 6 days. The pH of PCs was well maintained at the mean values of 7.0 in PO containers after 6 days in the well-oxygenated condition. The energy metabolism of stored platelets was determined. Oxygen consumption rates of platelets stored in PO containers averaged 1.5 nmol/min/10(9) platelets. The rates of glucose consumption and lactate production were 0.4 and 0.8 nmol/min/10(11) platelets, respectively. The rates of adenosine triphosphate (ATP) generation of platelets, 9.7 nmol/min/10(9) platelets, in PO containers did not differ from those in the PVC containers. Aggregation responses to adenosine diphosphate and hypotonic shock response of platelets were better maintained in PO containers. The morphological changes into sphere forms with projections and the appearance of unclassified forms were more frequently observed in PO than in PVC containers.(ABSTRACT TRUNCATED AT 250 WORDS)

Field Investigation of the Surface-deposited Radon Progeny as a Possible Predictor of the Airborne Radon Progeny Dose Rate

PubMed Central

Sun, Kainan; Steck, Daniel J.; Field, R. William

2009-01-01

The quantitative relationships between radon gas concentration, the surface-deposited activities of various radon progeny, the airborne radon progeny dose rate, and various residential environmental factors were investigated through actual field measurements in 38 selected Iowa houses occupied by either smokers or nonsmokers. Airborne dose rate was calculated from unattached and attached potential alpha energy concentrations (PAECs) using two dosimetric models with different activity-size weighting factors. These models are labeled Pdose and Jdose, respectively. Surface-deposited 218Po and 214Po were found significantly correlated to radon, unattached PAEC, and both airborne dose rates (p < 0.0001) in nonsmoking environments. However, deposited 218Po was not significantly correlated to the above parameters in smoking environments. In multiple linear regression analysis, natural logarithm transformation was performed for airborne dose rate as the dependent variable, as well as for radon and deposited 218Po and 214Po as predictors. An interaction effect was found between deposited 214Po and an obstacle in front of the Retrospective Reconstruction Detector (RRD) in predicting dose rate (p = 0.049 and 0.058 for Pdose and Jdose, respectively) for nonsmoking environments. After adjusting for radon and deposited radon progeny effects, the presence of either cooking, usage of a fireplace, or usage of a ceiling fan significantly, or marginal significantly, reduced the Pdose to 0.65 (90% CI 0.42–0.996), 0.54 (90% CI 0.28–1.02) and 0.66 (90% CI 0.45–0.96), respectively. For Jdose, only the usage of a ceiling fan significantly reduced the dose rate to 0.57 (90% CI 0.39–0.85). In smoking environments, deposited 218Po was a significant negative predictor for Pdose (RR 0.68, 90% CI 0.55–0.84) after adjusting for long-term 222Rn and environmental factors. A significant decrease of 0.72 (90% CI 0.64–0.83) in the mean Pdose was noted, after adjusting for the radon and radon progeny effects and other environmental factors, for every 10 increasing cigarettes smoked in the room. A significant increase of 1.71 in the mean Pdose was found for large room size relative to small room size (90% CI 1.08–2.79) after adjusting for the radon and radon progeny effects as well as other environmental factors. Fireplace usage was found to significantly increase the mean Pdose to 1.71 (90% CI 1.20–2.45) after adjusting for other factors. PMID:19590273

Experimental ammonia-free phosphate-bonded investments using Mg(H2PO4)2 solution.

PubMed

Takashiba, Shigeyuki; Zhang, Zutai; Tamaki, Yukimichi

2002-12-01

In our previous study, we investigated ammonia-free phosphate-bonded investments using Mg (H2PO4)2 powder. The purpose of the present study was to attempt usage of 50 wt% Mg (H2PO4)2 solution instead of powder. Magnesium oxide (MgO) was prepared as a binder and cristobalite was selected as a refractory. After arranging six kinds of experimental investments (A-F) with different cristobalite/MgO ratios, the fundamental properties of the dental investments were examined. The properties of the molds were influenced by the amount of MgO. Decreases in MgO showed lower mold strengths, longer setting time and larger setting expansion. According to XRD analysis, the peaks of MgH(PO4)3 x 3H2O newly formed, cristobalite and MgO were detected in the A set, but MgO peaks in F set were reduced. On the other hand, the surface of F was entirely covered by phosphorus. From these results, it was found that the usage of Mg(H2PO4)2 solution was possible for ammonia-free investments.

Facile synthesis of hierarchical Ag3PO4/TiO2 nanofiber heterostructures with highly enhanced visible light photocatalytic properties

NASA Astrophysics Data System (ADS)

Xie, Jinlei; Yang, Yefeng; He, Haiping; Cheng, Ding; Mao, Minmin; Jiang, Qinxu; Song, Lixin; Xiong, Jie

2015-11-01

Heterostructured semiconductor nanostructures have provoked great interest in the areas of energy, environment and catalysis. Herein, we report a novel hierarchical Ag3PO4/TiO2 heterostructure consisting of nearly spherical Ag3PO4 particles firmly coupled on the surface of TiO2 nanofibers (NFs). The construction of Ag3PO4/TiO2 heterostructure with tailored morphologies, compositions and optical properties was simply achieved via a facile and green synthetic strategy involving the electrospinning and solution-based processes. Owing to the synergetic effects of the components, the resulting hybrid heterostructures exhibited much improved visible light photocatalytic performance, which could degrade the RhB dye completely in 7.5 min. In addition, the coupling of Ag3PO4 particles with UV-light-sensitive TiO2 NFs enabled full utilization of solar energy and less consumption of noble metals, significantly appealing for their practical use in new energy sources and environmental issues. The developed synthetic strategy was considered to be applicable for the rational design and construction of other heterostructured catalysts.

Clearance of polonium-210-enriched cigarette smoke from the rat trachea and lung

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cohen, B.S.; Harley, N.H.; Tso, T.C.

The distribution and clearance of alpha radioactivity in the lungs of rats were measured after inhalation of smoke from cigarettes highly enriched in /sup 210/Po. Female Fischer rats were exposed daily for 6 months to smoke from cigarettes with 500 times the normal content of /sup 210/Po. Control rats were exposed to standard cigarette smoke. Animals were serially withdrawn and killed. After necropsy the trachea, major bronchi, larynx, and nasopharynx were examined for surface alpha activity by an etched track technique utilizing cellulose nitrate detectors. Areas of accumulated activity were seen on samples of larynx from rats exposed to themore » /sup 210/Po-enriched cigarettes. No other local accumulations were seen on the airways. The lower lungs were analyzed radiochemically for /sup 210/Po. Both radiochemical analysis and track measurements showed highly elevated activity concentrations in rats exposed to the /sup 210/Po-enriched cigarettes. Following withdrawal from smoking, both short- and long-term clearance components were seen. The parameters which fit the postexposure data for clearance of the lung burden cannot fit the buildup during the exposure period.« less

Clearance of polonium-210-enriched cigarette smoke from the rat trachea and lung.

PubMed

Cohen, B S; Harley, N H; Tso, T C

1985-06-30

The distribution and clearance of alpha radioactivity in the lungs of rats were measured after inhalation of smoke from cigarettes highly enriched in 210Po. Female Fischer rats were exposed daily for 6 months to smoke from cigarettes with 500 times the normal content of 210Po. Control rats were exposed to standard cigarette smoke. Animals were serially withdrawn and killed. After necropsy the trachea, major bronchi, larynx, and nasopharynx were examined for surface alpha activity by an etched track technique utilizing cellulose nitrate detectors. Areas of accumulated activity were seen on samples of larynx from rats exposed to the 210Po-enriched cigarettes. No other local accumulations were seen on the airways. The lower lungs were analyzed radiochemically for 210Po. Both radiochemical analysis and track measurements showed highly elevated activity concentrations in rats exposed to the 210Po-enriched cigarettes. Following withdrawal from smoking, both short- and long-term clearance components were seen. The parameters which fit the postexposure data for clearance of the lung burden cannot fit the buildup during the exposure period.

Kinetic Monte Carlo Study of Li Intercalation in LiFePO4.

PubMed

Xiao, Penghao; Henkelman, Graeme

2018-01-23

Even as a commercial cathode material, LiFePO 4 remains of tremendous research interest for understanding Li intercalation dynamics. The partially lithiated material spontaneously separates into Li-poor and Li-rich phases at equilibrium. Phase segregation is a surprising property of LiFePO 4 given its high measured rate capability. Previous theoretical studies, aiming to describe Li intercalation in LiFePO 4 , include both atomic-scale density functional theory (DFT) calculations of static Li distributions and entire-particle-scale phase field models, based upon empirical parameters, studying the dynamics of the phase separation. Little effort has been made to bridge the gap between these two scales. In this work, DFT calculations are used to fit a cluster expansion for the basis of kinetic Monte Carlo calculations, which enables long time scale simulations with accurate atomic interactions. This atomistic model shows how the phases evolve in Li x FePO 4 without parameters from experiments. Our simulations reveal that an ordered Li 0.5 FePO4 phase with alternating Li-rich and Li-poor planes along the ac direction forms between the LiFePO 4 and FePO 4 phases, which is consistent with recent X-ray diffraction experiments showing peaks associated with an intermediate-Li phase. The calculations also help to explain a recent puzzling experiment showing that LiFePO 4 particles with high aspect ratios that are narrower along the [100] direction, perpendicular to the [010] Li diffusion channels, actually have better rate capabilities. Our calculations show that lateral surfaces parallel to the Li diffusion channels, as well as other preexisting sites that bind Li weakly, are important for phase nucleation and rapid cycling performance.

Continuous arterial PO2 profiles in unrestrained, undisturbed aquatic turtles during routine behaviors

PubMed Central

Hicks, James W.

2016-01-01

ABSTRACT Mammals and birds maintain high arterial partial pressure of oxygen (PO2) values in order to preserve near-complete hemoglobin (Hb) oxygen (O2) saturation. In diving mammals and birds, arterial O2 follows a primarily monotonic decline and then recovers quickly after dives. In laboratory studies of submerged freshwater turtles, arterial O2 depletion typically follows a similar pattern. However, in these studies, turtles were disturbed, frequently tethered to external equipment and confined either to small tanks or breathing holes. Aquatic turtles can alter cardiac shunting patterns, which will affect arterial PO2 values. Consequently, little is known about arterial O2 regulation and use in undisturbed turtles. We conducted the first study to continuously measure arterial PO2 using implanted microelectrodes and a backpack logger in undisturbed red-eared sliders during routine activities. Arterial PO2 profiles during submergences varied dramatically, with no consistent patterns. Arterial PO2 was also lower than previously reported during all activities, with values rarely above 50 mmHg (85% Hb saturation). There was no difference in mean PO2 between five different activities: submerged resting, swimming, basking, resting at the surface and when a person was present. These results suggest significant cardiac shunting occurs during routine activities as well as submergences. However, the lack of relationship between PO2 and any activity suggests that cardiac shunts are not regulated to maintain high arterial PO2 values. These data support the idea that cardiac shunting is the passive by-product of regulation of vascular resistances by the autonomic nervous system. PMID:27618860

H2O2 rejuvenation-mediated synthesis of stable mixed-morphology Ag3PO4 photocatalysts.

PubMed

Agbe, Henry; Raza, Nadeem; Dodoo-Arhin, David; Chauhan, Aditya; Kumar, Ramachandran Vasant

2018-04-01

Ag 3 PO 4 photocatalyst has attracted interest of the scientific community in recent times due to its reported high efficiency for water oxidation and dye degradation. However, Ag 3 PO 4 photo-corrodes if electron accepter such as AgNO 3 is not used as scavenger. Synthesis of efficient Ag 3 PO 4 followed by a simple protocol for regeneration of the photocatalyst is therefore a prerequisite for practical application. Herein, we present a facile method for the synthesis of a highly efficient Ag 3 PO 4 , whose photocatalytic efficiency was demonstrated using 3 different organic dyes: Methylene Blue (MB), Methyl orange (MO) and Rhodamine B (RhB) organic dyes for degradation tests. Approximately, 19 % of Ag 3 PO 4 is converted to Ag 0 after 4.30 hours of continuous UV-Vis irradiation in presence of MB organic dye. We have shown that the Ag/Ag 3 PO 4 composite can be rejuvenated by a simple chemical oxidation step after several cycles of photocatalysis tests. At an optimal pH of 6.5, a mixture of cubic, rhombic dodecahedron, nanosphere and nanocrystals morphologies of the photocatalyst was formed. H 2 O 2 served as the chemical oxidant to re-insert the surface metallic Ag into the Ag 3 PO 4 photocatalyst but also as the agent that can control morphology of the regenerated as-prepared photocatalyst without the need for any other morphology controlling Agent (MCA). Surprisingly, the as- regenerated Ag 3 PO 4 was found to have higher photocatalytic reactivity than the freshly made material and superior at least 17 times in comparison with the conventional Degussa TiO 2 , and some of TiO 2 composites tested in this work.

Evaluation of nitrate and phosphate adsorption on Al-modified biochar: Influence of Al content.

PubMed

Yin, Qianqian; Ren, Huaipu; Wang, Ruikun; Zhao, Zhenghui

2018-08-01

Biochars with different Al contents (i.e., 5, 10, 15, and 20 wt%) were prepared to evaluate their adsorption capacities for nitrate (NO 3 - ) and phosphate (PO 4 3- ) from eutrophic water. Several techniques, including N 2 adsorption-desorption, X-ray diffraction, scanning electron microscopy, and Fourier transform infrared spectrometry, were applied to characterize the physical-chemical properties of the biochars. We found that the NO 3 - and PO 4 3- adsorptions significantly improved on the Al-modified biochars because of their multifunctional and surface charge properties. In single-solute adsorption, 15 Al/BC and 20 Al/BC exhibited optimal NO 3 - and PO 4 3- adsorption capacities, respectively. In bi-solute coadsorption, the PO 4 3- adsorption on the biochar was less affected with the coexistence of NO 3 - , whereas the coexistence of PO 4 3- had a significant impact on the NO 3 - adsorption. The optimal solution pH for NO 3 - adsorption was 6, and pH < 6 was advantageous to PO 4 3- adsorption. In the kinetic study, the pseudo-second-order model could describe the NO 3 - and PO 4 3- adsorptions on biochar well, indicating that chemical adsorption was the main adsorption mechanism. The Langmuir-Freundlich model agreed well with the NO 3 - and PO 4 3- adsorptions on the biochars, and the maximum adsorption capacities for NO 3 - and PO 4 3- reached 89.58 mg/g and 57.49 mg/g, respectively. Therefore, the Al-modified biochar was a good choice for the remediation of eutrophic water. Copyright © 2018 Elsevier B.V. All rights reserved.

[The effects of surface morphology of calcium phosphate ceramics on apatite formation in dynamic SBF].

PubMed

Duan, Yourong; Lü, Wanxin; Wang, Chaoyuan; Chen, Jiyong; Zhang, Xingdong

2002-06-01

Bone-like apatite formation on the surface of calcium phosphate ceramics has been believed to be the prerequisite of new bone growth on ceramics and to be related to the osteoinductivity of the material. The research of the factors effecting bone-like apatite formation is a great help in understanding the mechanism of osteoinduction. This paper is aimed to a comparative study of in vitro formation of bone-like apatite on the surface of dense and rough calcium phosphate ceramics with SBF flowing at different rates. The results showed that the rough surface was beneficial to the formation of bone-like apatite, and the apatite formed faster in 1.5 SBF than in SBF. Rough surface, namely, larger surface area, increased the dissolution of Ca2+ and HPO4(2-) and higher concentration of Ca2+ and HPO4(2-) ions of SBF and was in turn advantageous to the accumulation of Ca2+, HPO4(2-), PO4(3-) near the ceramic surface. Local supersaturating concentration of Ca2+, HPO4(2-), PO4(3-) near sample surface was essential to nucleation of apatite on the surface of sample.

Tissue oxygen measurement system

NASA Technical Reports Server (NTRS)

Soller, Babs R. (Inventor)

2004-01-01

A device and method in accordance with the invention for determining the oxygen partial pressure (PO.sub.2) of a tissue by irradiating the tissue with optical radiation such that the light is emitted from the tissue, and by collecting the reflected or transmitted light from the tissue to form an optical spectrum. A spectral processor determines the PO.sub.2 level in tissue by processing this spectrum with a previously-constructed spectral calibration model. The tissue may, for example, be disposed underneath a covering tissue, such as skin, of a patient, and the tissue illuminated and light collected through the skin. Alternatively, direct tissue illumination and collection may be effected with a hand-held or endoscopic probe. A preferred system also determines pH from the same spectrum, and the processor may determine critical conditions and issue warnings based on parameter values.

Liquid Surface Levitation Holography. Part 1. Theoretical Analysis.

DTIC Science & Technology

1980-08-11

mass and momentum conservation equations. The inequality Plt >> YV I2hi," in conjunction with the relation hla - 0(Via/ao,,) requires that ,/poC2 a...in the upper fluid be given by r fu = f 4u(wi, w) e2lr i )y e2briO e- i didoi. ( B27 ) The boundary condition ,z = i’ at z = 0 gives = 4At Ybi 2poA

Particle Scavenging and Tidal Exchange of Po-210 and Th-234 in a Mesotidal Embayment in Southern California

NASA Astrophysics Data System (ADS)

Peng, J.; Ku, T.; Luo, S.

2002-12-01

San Diego Bay (SDB) is a semi-closed shallow embayment that sustains semidiurnal tides and continuous tidal flows. We measured Po-210 and Th-234 activities in water samples collected from across north SDB, coastal waters immediately outside SDB, and from several rivers in the vicinity of SDB. A station in north SDB was sampled multiple times during a complete flooding-ebbing cycle. The major findings are as follows. 1) Compared to the outer sea, SDB water has much higher Th-234 deficiency (1.3-2.0 dpm/l, vs. 0.4-0.8dpm/l for outer sea) and considerably lower Po-210 activities (averaging 0.05dpm/l vs. 0.07dpm/l for outer sea) due to stronger particle scavenging. There is higher particulate Po-210 vs. total Po-210 ratio in SDB water (68%, vs. 34% for outer sea). 2) Inside SDB, an increasing Po-210 activities towards the bay mouth clearly indicates the effect of tidal exchange. Po-210 activity near the Bay mouth exceeds that of the outer sea due to higher particulate Po-210, which may come from tidal-induced sediment resuspension. 3) Rivers flowing into or near SDB have 8-12 times higher Po-210 activities than the bay water. But the input of Po-210 to SDB from rivers should be insignificant because of the negligible flow in the dry season. 4) In a tidal cycle, both Po-210 and Th-234 activities in North Bay covary with tidal pattern, which can be readily explained by the exchange between two waters inside and outside SDB with distinct TSS levels and Po-210/Th-234 activities. Sediment resuspension plays an important role during the peak tidal flow, resulting in an asymmetrical time-evolution curve of Po-210/Th-234 activities. These observations correspond well with our previous finding of systematic variations of Po-210 and Th-234 activities in water and sediment columns across SDB. This study manifests the significance of hydrodynamic processes such as advection, mixing and particle movement in the study of geochemistry of particle-reactive radionuclides in a tidal embayment. Since the geochemical behavior of these particle-reactive radionuclides mimic those of many hydrophobic contaminants such as PCBs, DDT, and heavy metals, this study also bears implications for the transport and fate of hydrophobic contaminants in aqueous environment.

New anti fouling coatings based on conductive polymers.

DOT National Transportation Integrated Search

2009-10-01

Traditional antifouling paints were designed to release toxins from the surface of the paint to prevent micro-organisms attaching to the surface. The toxicity of the released chemical species has been found to be damaging to the marine ecology and po...

Application of a transmission model to estimate performance objectives for Salmonella in the broiler supply chain.

PubMed

van der Fels-Klerx, H J; Tromp, S; Rijgersberg, H; van Asselt, E D

2008-11-30

The aim of the present study was to demonstrate how Performance Objectives (POs) for Salmonella at various points in the broiler supply chain can be estimated, starting from pre-set levels of the PO in finished products. The estimations were performed using an analytical transmission model, based on prevalence data collected throughout the chain in The Netherlands. In the baseline (current) situation, the end PO was set at 2.5% of the finished products (at end of processing) being contaminated with Salmonella. Scenario analyses were performed by reducing this baseline end PO to 1.5% and 0.5%. The results showed the end PO could be reduced by spreading the POs over the various stages of the broiler supply chain. Sensitivity analyses were performed by changing the values of the model parameters. Results indicated that, in general, decreasing Salmonella contamination between points in the chain is more effective in reducing the baseline PO than increasing the reduction of the pathogen, implying contamination should be prevented rather than treated. Application of both approaches at the same time showed to be most effective in reducing the end PO, especially at the abattoir and during processing. The modelling approach of this study proved to be useful to estimate the implications for preceding stages of the chain by setting a PO at the end of the chain as well as to evaluate the effectiveness of potential interventions in reducing the end PO. The model estimations may support policy-makers in their decision-making process with regard to microbiological food safety.

The impact of tobacco promotion at the point of sale: a systematic review.

PubMed

Paynter, Janine; Edwards, Richard

2009-01-01

Tobacco promotion increases the likelihood that adolescents will start smoking. Much of the tobacco industry's promotional budget is spent on point of sale (PoS) promotion in many jurisdictions. Consequently, tobacco is an eye-catching feature at the PoS in many places. We reviewed the evidence that PoS tobacco promotion influences key smoking-related behaviors and beliefs, increases susceptibility to smoking in youth, undermines smokers' quit attempts, and promotes relapse among ex-smokers. We found 12 peer-reviewed studies, 10 of which were focused on children. Seven of 8 observational studies found statistically significant associations between exposure to tobacco promotion at the PoS and smoking initiation or susceptibility to smoking. Two experimental studies of children found statistically significant associations between exposure to PoS tobacco promotions and beliefs about ease of getting tobacco and smoking prevalence among their peers. An experimental study with adults found that a picture of collected tobacco pack elicited cravings for cigarettes among smokers. A cross-sectional study found that 25% of adult smokers reported impulse purchasing and a third of recent ex-smokers reported urges to start smoking after seeing tobacco displayed. More prospective studies are needed to clarify the temporal relationship between exposure to PoS tobacco and outcome. However, given the addictiveness of tobacco, the severity of the health hazards posed by smoking, the evidence that tobacco promotion encourages children to start smoking, and the consistency of the evidence that PoS promotion influences children's smoking, we believe that ample justification exists for banning PoS advertising and displays of smoked tobacco products.

Analysing a cycling grand tour: Can we monitor fatigue with intensity or load ratios?

PubMed

Sanders, Dajo; Heijboer, Mathieu; Hesselink, Matthijs K C; Myers, Tony; Akubat, Ibrahim

2018-06-01

This study evaluated the changes in ratios of different intensity (rating of perceived exertion; RPE, heart rate; HR, power output; PO) and load measures (session-RPE; sRPE, individualized TRIMP; iTRIMP, Training Stress Score™; TSS) in professional cyclists. RPE, PO and HR data was collected from twelve professional cyclists (VO 2max 75 ± 6 ml∙min∙kg -1 ) during a two-week baseline training period and during two cycling Grand Tours. Subjective:objective intensity (RPE:HR, RPE:PO) and load (sRPE:iTRIMP, sRPE:TSS) ratios and external:internal intensity (PO:HR) and load (TSS:iTRIMP) ratios were calculated for every session. Moderate to large increases in the RPE:HR, RPE:PO and sRPE:TSS ratios (d = 0.79-1.79) and small increases in the PO:HR and sRPE:iTRIMP ratio (d = 0.21-0.41) were observed during Grand Tours compared to baseline training data. Differences in the TSS:iTRIMP ratio were trivial to small (d = 0.03-0.27). Small to moderate week-to-week changes (d = 0.21-0.63) in the PO:HR, RPE:PO, RPE:HR, TSS:iTRIMP, sRPE:iTRIMP and sRPE:TSS were observed during the Grand Tour. Concluding, this study shows the value of using ratios of intensity and load measures in monitoring cyclists. Increases in ratios could reflect progressive fatigue that is not readily detected by changes in solitary intensity/load measures.

210Po, 210Pb, 40K and 137Cs in edible wild berries and mushrooms and ingestion doses to man from high consumption rates of these wild foods.

PubMed

Gwynn, Justin P; Nalbandyan, Anna; Rudolfsen, Geir

2013-02-01

This paper discusses activity concentrations of (210)Po, (210)Pb, (40)K and (137)Cs in edible wild berries and mushrooms collected from Øvre Dividalen national park, Northern Norway and derives committed effective ingestion doses to man based on high consumption rates of these wild foods. Edible wild berries and mushrooms accumulated similar levels of (210)Pb, but mushrooms accumulated higher levels of (210)Po and (40)K than berries. There appears to be a clear difference in the ability of Leccinum spp. of fungi to accumulate (210)Po and/or translocate (210)Po to mushrooms compared to Russula spp. of fungi. Activity concentrations of (137)Cs in edible wild berries and mushrooms from Øvre Dividalen national park reflected the lower levels of fallout of this radionuclide in Northern Norway compared to more central areas following the Chernobyl accident. For mushrooms, ingestion doses are dominated by (210)Po, while for berries, (40)K is typically the main contributor to dose. Based on high consumption rates, ingestion doses arising from the combination of (210)Po, (210)Pb and (40)K were up to 0.05 mSv/a for berries and 0.50 mSv/a for mushrooms. Consumption of such wild foods may result in a significant contribution to total annual doses when consumed in large quantities, particularly when selecting mushrooms species that accumulate high activity concentrations of (210)Po. Copyright © 2012 Elsevier Ltd. All rights reserved.

Patterns of phenoloxidase activity in insecticide resistant and susceptible mosquitoes differ between laboratory-selected and wild-caught individuals.

PubMed

Cornet, Stéphane; Gandon, Sylvain; Rivero, Ana

2013-10-31

Insecticide resistance has the potential to alter vector immune competence and consequently affect the transmission of diseases. Using both laboratory isogenic strains and field-caught Culex pipiens mosquitoes, we investigated the effects of insecticide resistance on an important component of the mosquito immune system: the phenoloxidase (PO) activity. As infection risk varies dramatically with the age and sex of mosquitoes, allocation to PO immunity was quantified across different stages of the mosquito life cycle. Our results were consistent in showing that larvae have a higher PO activity than adults, females have a higher PO activity than males, and PO activity declines with adult age. We obtained, however, a marked discrepancy between laboratory and field-collected mosquitoes on the effect of insecticide resistance on PO activity. In the laboratory selected strains we found evidence of strong interactions between insecticide resistance and the age and sex of mosquitoes. In particular, 7 and 14 day old esterase-resistant adult females and acetylcholine-esterase resistant males had significantly higher PO activities than their susceptible counterparts. No such effects were, however, apparent in field-caught mosquitoes. Combined, the field and laboratory-based approaches employed in this study provide a powerful test of the effect of insecticide resistance on PO-mediated immunity. The use of laboratory-selected insecticide-resistant strains is still the most widely used method to investigate the pleiotropic effects of insecticide resistance. Our results suggest that the outcome of these laboratory-selected mosquitoes must be interpreted with caution and, whenever possible, compared with mosquitoes captured from the field.

Removal of the long-lived {sup 222}Rn daughters from steel and germanium surfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wojcik, Marcin; Zuzel, Grzegorz; Majorovits, Bela

Removal of the long-lived {sup 222}Rn daughters ({sup 210}Pb, {sup 210}Bi and {sup 210}Po) from stainless steel and germanium surfaces was investigated. As cleaning technique etching was applied to samples in a form of discs exposed earlier to a strong radon source. Reduction of the {sup 210}Pb activity was tested using a HPGe spectrometer, for {sup 210}Bi a beta spectrometer and for {sup 210}Po an alpha spectrometer was used. According to the conducted measurements all the isotopes were removed very efficiently from germanium. Results obtained for stainless steel were worse but still better than those achieved for copper.

Influence of polarized PZT on the crystal growth of calcium phosphate

NASA Astrophysics Data System (ADS)

Sun, Xiaodan; Ma, Chunlai; Wang, Yude; Li, Hengde

2002-01-01

The effects of polarization on the crystallization of calcium phosphate are studied in this work. Crystals of calcium phosphate from saturated solution of hydroxyapatite (HA, Ca 10(PO 4) 6(OH) 2) were deposited on the surfaces of ferroelectric ceramics lead zirconate titanium (Pb(Ti,Zr)O 3, PZT). The results of the experiment demonstrated the acceleration effects of polarized PZT on the crystal growth of calcium phosphate. Furthermore, it is indicated that polarization also influenced the orientation of the deposited crystals due to the growth of a layer of (0 0 2) oriented octacalcium phosphate (OCP, Ca 8H 2(PO 4) 6·5H 2O) on the negatively charged surfaces of PZT.

Relevance of LiPF6 as Etching Agent of LiMnPO4 Colloidal Nanocrystals for High Rate Performing Li-ion Battery Cathodes.

PubMed

Chen, Lin; Dilena, Enrico; Paolella, Andrea; Bertoni, Giovanni; Ansaldo, Alberto; Colombo, Massimo; Marras, Sergio; Scrosati, Bruno; Manna, Liberato; Monaco, Simone

2016-02-17

LiMnPO4 is an attractive cathode material for the next-generation high power Li-ion batteries, due to its high theoretical specific capacity (170 mA h g(-1)) and working voltage (4.1 V vs Li(+)/Li). However, two main drawbacks prevent the practical use of LiMnPO4: its low electronic conductivity and the limited lithium diffusion rate, which are responsible for the poor rate capability of the cathode. The electronic resistance is usually lowered by coating the particles with carbon, while the use of nanosize particles can alleviate the issues associated with poor ionic conductivity. It is therefore of primary importance to develop a synthetic route to LiMnPO4 nanocrystals (NCs) with controlled size and coated with a highly conductive carbon layer. We report here an effective surface etching process (using LiPF6) on colloidally synthesized LiMnPO4 NCs that makes the NCs dispersible in the aqueous glucose solution used as carbon source for the carbon coating step. Also, it is likely that the improved exposure of the NC surface to glucose facilitates the formation of a conductive carbon layer that is in intimate contact with the inorganic core, resulting in a high electronic conductivity of the electrode, as observed by us. The carbon coated etched LiMnPO4-based electrode exhibited a specific capacity of 118 mA h g(-1) at 1C, with a stable cycling performance and a capacity retention of 92% after 120 cycles at different C-rates. The delivered capacities were higher than those of electrodes based on not etched carbon coated NCs, which never exceeded 30 mA h g(-1). The rate capability here reported for the carbon coated etched LiMnPO4 nanocrystals represents an important result, taking into account that in the electrode formulation 80% wt is made of the active material and the adopted charge protocol is based on reasonable fast charge times.

Synthesis and characterization of Silica/polyvinyl imidazole/H2PO4-core-shell nanoparticles as recyclable adsorbent for efficient scavenging of Sm(III) and Dy(III) from water.

PubMed

Ettehadi Gargari, Jafar; Sid Kalal, Hossein; Shakeri, Alireza; Khanchi, Alireza

2017-11-01

In this study, we used Silica/polyvinyl imidazole core-shell nanoparticles impregnated with sodium dihydrogen phosphate (SiO 2 /PVI/H 2 PO 4 - NPs) for adsorption of samarium and dysprosium ions from aqueous solutions. The effects of the pH, adsorbent dose, contact time, and initial concentration of the adsorbate on the Core-shell nanoparticles adsorption capacity have been studied. The pH value for maximum removal of Sm (III) and Dy (III) on the core-shell nanoparticles surface were found to be 4. The saturated capacity of SiO 2 /PVI/H 2 PO 4 - NPs was up to 160mg.g -1 and 150mg.g -1 at 25°C for Sm (III) and Dy (III) ions respectively. The obtained uptake data were analyzed by the Langmuir and Freundlich equations using a linearized correlation coefficient at room temperature. The Freundlich isotherm was found to fit well with the equilibrium data. The adsorption kinetics could be modeled by a pseudo-second-order rate expression. Thermodynamic investigation revealed the adsorption process of the studied ions is entropy driven. Furthermore, the performance of regeneration and reutilization were studied. The adsorbed Sm (III) and Dy (III) can be desorbed by 0.5mol/L HCl, with the desorption percentage of 90% for Sm (III) and Dy (III). After five adsorption-desorption cycles, the adsorption capacity shows a slight decrease (about 15%), implying that the SiO 2 /PVI/H 2 PO 4 - NPs can be used as an effective adsorbent for the removal and recovery of Sm(III) and Dy(III) from aqueous solution. The colloid stability of the SiO 2 /PVI/H 2 PO 4 - NPs was investigated by dynamic light scattering measurements. The SiO 2 /PVI/H 2 PO 4 - NPs are stable in adsorption media after five adsorption - desorption cycles. The high stability of SiO 2 /PVI/H 2 PO 4 - NPs can be attributed to steric stabilization by polyvinyl imidazole adsorbed on SiO 2 nanoparticle surfaces. Copyright © 2017 Elsevier Inc. All rights reserved.

Advanced carbon materials/olivine LiFePO4 composites cathode for lithium ion batteries

NASA Astrophysics Data System (ADS)

Gong, Chunli; Xue, Zhigang; Wen, Sheng; Ye, Yunsheng; Xie, Xiaolin

2016-06-01

In the past two decades, LiFePO4 has undoubtly become a competitive candidate for the cathode material of the next-generation LIBs due to its abundant resources, low toxicity and excellent thermal stability, etc. However, the poor electronic conductivity as well as low lithium ion diffusion rate are the two major drawbacks for the commercial applications of LiFePO4 especially in the power energy field. The introduction of highly graphitized advanced carbon materials, which also possess high electronic conductivity, superior specific surface area and excellent structural stability, into LiFePO4 offers a better way to resolve the issue of limited rate performance caused by the two obstacles when compared with traditional carbon materials. In this review, we focus on advanced carbon materials such as one-dimensional (1D) carbon (carbon nanotubes and carbon fibers), two-dimensional (2D) carbon (graphene, graphene oxide and reduced graphene oxide) and three-dimensional (3D) carbon (carbon nanotubes array and 3D graphene skeleton), modified LiFePO4 for high power lithium ion batteries. The preparation strategies, structure, and electrochemical performance of advanced carbon/LiFePO4 composite are summarized and discussed in detail. The problems encountered in its application and the future development of this composite are also discussed.

Microwave synthesis of molybdenum doped LiFePO4/C and its electrochemical studies.

PubMed

Naik, Amol; P, Sajan C

2016-05-10

A Mo-doped LiFePO4 composite was prepared successfully from an iron carbonyl complex by adopting a facile and rapid microwave assisted solid state method. The evolution of gases from the iron precursor produces a highly porous product. The formation and substitution of Mo in LiFePO4 were confirmed by X-ray diffraction; surface analysis was carried out by scanning electron microscopy, field emission scanning electron microscopy, and transmission electron microscopy. The electrochemical properties of the substituted LiFePO4 were examined by cyclic voltammetry, electrochemical impedance spectroscopy and by recording charge-discharge cycles. It was observed that the as prepared composites consisted of a single phase orthorhombic olivine-type structure, where Mo(6+) was successfully introduced into the M2(Fe) sites. Incorporation of supervalent Mo(6+) introduced Li(+) ion vacancies in LiFePO4. The synthesized material facilitated lithium ion diffusion during charging/discharging due to the charge compensation effect and porosity. The battery performance studies showed that LiMo0.05Fe0.095PO4 exhibited a maximum capacity of 169.7 mA h g(-1) at 0.1 C current density, with admirable stability retention. Even at higher current densities, the retention of the specific capacity was exceptional.

Synergistic effect in carbon coated LiFePO4 for high yield spontaneous grafting of diazonium salt. Structural examination at the grain agglomerate scale.

PubMed

Madec, Lénaïc; Robert, Donatien; Moreau, Philippe; Bayle-Guillemaud, Pascale; Guyomard, Dominique; Gaubicher, Joël

2013-08-07

Molecular grafting of p-nitrobenzene diazonium salt at the surface of (Li)FePO4-based materials was thoroughly investigated. The grafting yields obtained by FTIR, XPS, and elemental analysis for core shell LiFePO4-C are found to be much higher than the sum of those associated with either the LiFePO4 core or the carbon shell alone, thereby revealing a synergistic effect. Electrochemical, XRD, and EELS experiments demonstrate that this effect stems from the strong participation of the LiFePO4 core that delivers large amounts of electrons to the carbon substrate at a constant energy, above the Fermi level of the diazonium salt. Correspondingly large multilayer anisotropic structures that are associated with outstanding grafting yields could be observed from TEM experiments. Results therefore constitute strong evidence of a grafting mechanism where homolytic cleavage of the N2(+) species occurs together with the formation and grafting of radical nitro-aryl intermediates. Although the oxidation and concomitant Li deintercalation of LiFePO4 grains constitute the main driving force of the functionalization reaction, EFTEM EELS mapping shows a striking lack of spatial correlation between grafted grains and oxidized ones.

Accelerated effects of nano-ZnO on phosphorus removal by Chlorella vulgaris: Formation of zinc phosphate crystallites.

PubMed

Xiao, Huaixian; Liu, Na; Tian, Ke; Liu, Shixiang; Ge, Fei

2018-09-01

Nanoparticles have been reported to induce toxicity to aquatic organisms, however, their potential impacts on phosphorus removal from wastewater by algae are unclear. In this study, the effects of nanoparticle ZnO (nano-ZnO) on phosphate (PO 4 3- ) removal by a green alga Chlorella vulgaris were investigated. We found that PO 4 3- removal efficiency was accelerated with high concentrations of nano-ZnO (0.04-0.15mM) but reduced with low concentrations of nano-ZnO (0.005-0.04mM) compared to the control (without nano-ZnO), suggesting that PO 4 3- removal efficiency by C. vulgaris was related to nano-ZnO concentrations. Moreover, we observed changes of nano-ZnO morphology and detected element P on the surface of nano-ZnO by using transmission electronic microscopy (TEM) combined with energy dispersive X-ray spectroscopy (EDX), indicating that PO 4 3- was interacted with nano-ZnO or the dissolved Zn 2+ from nano-ZnO. Furthermore, we confirmed this interaction induced the formation of Zn 3 (PO 4 ) 2 crystallites sedimentation by employing X-ray diffraction analysis (XRD) and X-ray photoelectron spectroscopy (XPS), which finally accelerates the removal of PO 4 3- . Copyright © 2018 Elsevier B.V. All rights reserved.

Poás volcano in Costa Rica as a hydrothermal analog for Mars

NASA Astrophysics Data System (ADS)

Elmaarry, M. R.; Hynek, B. M.

2017-12-01

Mars has experienced intensive volcanic and impact activity early in its history, coinciding with a similarly extensive hydrologic activity on a global scale. These activities constitute the main ingredients of hydrothermal activity. Data acquired from the study of Martian meteorites, remote sensing spectral observations, and robotic rovers has shown the surface of Mars to be mineralogically diverse including mineral assemblages that resemble those of analogous hydrothermal systems on Earth. In particular, evidence for extensive acid-sulfate weathering has been observed by the MERs at Gusev and Meridiani, as well as by MSL at Gale crater. Furthermore, there is growing evidence for silicic volcanism on Mars as indicated by the detection of silica-rich mudstone at Gale containing tridymite and cristobalite coupled with spectral observations indicative of felsic rocks in geographically disparate locations on Mars. For that, the Poás volcano in Costa Rica offers a geologic setting that can be analogous to similar environments on Mars. The Poás volcano is a basaltic andesite stratovolcano in central Costa Rica. Its caldera houses a highly acidic lake inside the caldera 130 m below the crater rim. The volcano has been active in recent historical times, and is currently displaying intensive activity since Apr 2017. Unaltered andesitic basalts collected from the 1953-1955 magmatic activity are mainly composed of plagioclase and minor amounts of orthopyroxene and olivine. We collected samples during our fieldwork in March 2017 (few weeks before its eruption) from fumaroles inside the caldera. The fumaroles were emitting gases at 92°C, and the acidic lake < 20 m away had a pH of 1.5. XRD analysis of samples taken from 4 different fumaroles shows high concentrations of elemental sulfur, gypsum, alunite, and cristobalite along with minor abundances of hematite, anatase, and amorphous silica. Most of these minerals have been observed on Mars under potentially similar settings. We plan to continue our investigation by carrying out additional analyses and compare to samples collected from earlier campaigns to gain a better understanding of how the mineralogy changes with ambient conditions and look for short-term changes, which may help constrain further the conditions in which similar assemblages may have formed on Mars.

Best Practices for International Collaboration and Applications of Interoperability within a NASA Data Center

NASA Astrophysics Data System (ADS)

Moroni, D. F.; Armstrong, E. M.; Tauer, E.; Hausman, J.; Huang, T.; Thompson, C. K.; Chung, N.

2013-12-01

The Physical Oceanographic Distributed Active Archive Center (PO.DAAC) is one of 12 data centers sponsored by NASA's Earth Science Data and Information System (ESDIS) project. The PO.DAAC is tasked with archival and distribution of NASA Earth science missions specific to physical oceanography, many of which have interdisciplinary applications for weather forecasting/monitoring, ocean biology, ocean modeling, and climate studies. PO.DAAC has a 20-year history of cross-project and international collaborations with partners in Europe, Japan, Australia, and the UK. Domestically, the PO.DAAC has successfully established lasting partners with non-NASA institutions and projects including the National Oceanic and Atmospheric Administration (NOAA), United States Navy, Remote Sensing Systems, and Unidata. A key component of these partnerships is PO.DAAC's direct involvement with international working groups and science teams, such as the Group for High Resolution Sea Surface Temperature (GHRSST), International Ocean Vector Winds Science Team (IOVWST), Ocean Surface Topography Science Team (OSTST), and the Committee on Earth Observing Satellites (CEOS). To help bolster new and existing collaborations, the PO.DAAC has established a standardized approach to its internal Data Management and Archiving System (DMAS), utilizing a Data Dictionary to provide the baseline standard for entry and capture of dataset and granule metadata. Furthermore, the PO.DAAC has established an end-to-end Dataset Lifecycle Policy, built upon both internal and external recommendations of best practices toward data stewardship. Together, DMAS, the Data Dictionary, and the Dataset Lifecycle Policy provide the infrastructure to enable standardized data and metadata to be fully ingested and harvested to facilitate interoperability and compatibility across data access protocols, tools, and services. The Dataset Lifecycle Policy provides the checks and balances to help ensure all incoming HDF and netCDF-based datasets meet minimum compliance requirements with the Lawrence Livermore National Laboratory's actively maintained Climate and Forecast (CF) conventions with additional goals toward metadata standards provided by the Attribute Convention for Dataset Discovery (ACDD), the International Organization for Standardization (ISO) 19100-series, and the Federal Geographic Data Committee (FGDC). By default, DMAS ensures all datasets are compliant with NASA's Global Change Master Directory (GCMD) and NASA's Reverb data discovery clearinghouse (also known as ECHO). For data access, PO.DAAC offers several widely-used technologies, including File Transfer Protocol (FTP), Open-source Project for a Network Data Access Protocol (OPeNDAP), and Thematic Realtime Environmental Distributed Data Services (THREDDS). These access technologies are available directly to users or through PO.DAAC's web interfaces, specifically the High-level Tool for Interactive Data Extraction (HiTIDE), Live Access Server (LAS), and PO.DAAC's set of search, image, and Consolidated Web Services (CWS). Lastly, PO.DAAC's newly introduced, standards-based CWS provide singular endpoints for search, imaging, and extraction capabilities, respectively, across L2/L3/L4 datasets. Altogether, these tools, services and policies serve to provide flexible, interoperable functionality for both users and data providers.

Titanate nanotube thin films with enhanced thermal stability and high-transparency prepared from additive-free sols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koroesi, Laszlo, E-mail: korosi@enviroinvest.hu; Department of Biotechnology, Nanophage Therapy Center, Enviroinvest Corporation, Kertvaros utca 2, H-7632 Pecs; Papp, Szilvia

2012-08-15

Titanate nanotubes were synthesized from TiO{sub 2} in alkaline medium by a conventional hydrothermal method (150 Degree-Sign C, 4.7 bar). To obtain hydrogen titanates, the as-prepared sodium titanates were treated with either HCl or H{sub 3}PO{sub 4} aqueous solutions. A simple synthesis procedure was devised for stable titanate nanotube sols without using any additives. These highly stable ethanolic sols can readily be used to prepare transparent titanate nanotube thin films of high quality. The resulting samples were studied by X-ray diffraction, N{sub 2}-sorption measurements, Raman spectroscopy, transmission and scanning electron microscopy, X-ray photoelectron spectroscopy and spectroscopic ellipsometry. The comparative resultsmore » of using two kinds of acids shed light on the superior thermal stability of the H{sub 3}PO{sub 4}-treated titanate nanotubes (P-TNTs). X-ray photoelectron spectroscopy revealed that P-TNTs contains P in the near-surface region and the thermal stability was enhanced even at a low ({approx}0.5 at%) concentration of P. After calcination at 500 Degree-Sign C, the specific surface areas of the HCl- and H{sub 3}PO{sub 4}-treated samples were 153 and 244 m{sup 2} g{sup -1}, respectively. The effects of H{sub 3}PO{sub 4} treatment on the structure, morphology and porosity of titanate nanotubes are discussed. - Graphical Abstract: TEM picture (left) shows P-TNTs with diameters about 5-6 nm. Inset shows a stable titanate nanotube sol illuminated by a 532 nm laser beam. Due to the presence of the nanoparticles the way of the light is visible in the sol. Cross sectional SEM picture (right) as well as ellipsometry revealed the formation of optical quality P-TNT films with thicknesses below 50 nm. Highlights: Black-Right-Pointing-Pointer H{sub 3}PO{sub 4} treatment led to TNTs with high surface area even after calcination at 500 Degree-Sign C. Black-Right-Pointing-Pointer H{sub 3}PO{sub 4}-treated TNTs preserved their nanotube morphology up to 500 Degree-Sign C. Black-Right-Pointing-Pointer Stable TNT sols can be prepared by the peptization of TNT gels. Black-Right-Pointing-Pointer High-transparency TNT thin films of high quality were fabricated.« less

Phase-field modeling of diffusional phase behaviors of solid surfaces: A case study of phase-separating Li XFePO 4 electrode particles

DOE PAGES

Heo, Tae Wook; Chen, Long-Qing; Wood, Brandon C.

2015-04-08

In this paper, we present a comprehensive phase-field model for simulating diffusion-mediated kinetic phase behaviors near the surface of a solid particle. The model incorporates elastic inhomogeneity and anisotropy, diffusion mobility anisotropy, interfacial energy anisotropy, and Cahn–Hilliard diffusion kinetics. The free energy density function is formulated based on the regular solution model taking into account the possible solute-surface interaction near the surface. The coherency strain energy is computed using the Fourier-spectral iterative-perturbation method due to the strong elastic inhomogeneity with a zero surface traction boundary condition. Employing a phase-separating Li XFePO 4 electrode particle for Li-ion batteries as a modelmore » system, we perform parametric three-dimensional computer simulations. The model permits the observation of surface phase behaviors that are different from the bulk counterpart. For instance, it reproduces the theoretically well-established surface modes of spinodal decomposition of an unstable solid solution: the surface mode of coherent spinodal decomposition and the surface-directed spinodal decomposition mode. We systematically investigate the influences of major factors on the kinetic surface phase behaviors during the diffusional process. Finally, our simulation study provides insights for tailoring the internal phase microstructure of a particle by controlling the surface phase morphology.« less

Multiple response optimization of the coagulation process for upgrading the quality of effluent from municipal wastewater treatment plant

NASA Astrophysics Data System (ADS)

Li, Na; Hu, Yi; Lu, Yong-Ze; Zeng, Raymond J.; Sheng, Guo-Ping

2016-05-01

To meet the high quality standard of receiving water, the coagulation process using polyferric chloride (PFC) was used to further improve the water quality of effluent from wastewater treatment plants. Uniform design (UD) coupled with response surface methodology (RSM) was adopted to assess the effects of the main influence factors: coagulant dosage, pH and basicity, on the removal of total organic carbon (TOC), NH4+-N and PO43--P. A desirability function approach was used to effectively optimize the coagulation process for the comprehensive removal of TOC, NH4+-N and PO43--P to upgrade the effluent quality in practical application. The optimized operating conditions were: dosage 28 mg/L, pH 8.5 and basicity 0.001. The corresponding removal efficiencies for TOC, NH4+-N and PO43--P were 77.2%, 94.6% and 20.8%, respectively. More importantly, the effluent quality could upgrade to surface water Class V of China through coagulation under optimal region. In addition, grey relational analysis (GRA) prioritized these three factors as: pH > basicity > dosage (for TOC), basicity > dosage > pH (for NH4+-N), pH > dosage > basicity (for PO43--P), which would help identify the most important factor to control the treatment efficiency of various effluent quality indexes by PFC coagulation.

In-situ growth of graphene decorations for high-performance LiFePO4 cathode through solid-state reaction

NASA Astrophysics Data System (ADS)

Li, Jing; Zhang, Li; Zhang, Longfei; Hao, Weiwei; Wang, Haibo; Qu, Qunting; Zheng, Honghe

2014-03-01

Graphene-decorated LiFePO4 composite is synthesized for the first time through in-situ pyrolysis and catalytic graphitization, in which glucose and a trace amount of FeSO4 are employed as the graphene source and catalyst precursor, respectively. Under Ar/H2 (95:5) atmosphere at 750 °C, FeSO4 is thermally reduced to Fe nano-particles (Fe NPs) and glucose is pyrolyzed to carbon fragments first, followed by the in-situ growth of graphene sheets directly on the LiFePO4 nano-particles (LFP NPs) surface through the realignment of carbon fragments under the catalytic effect of the Fe NPs. The graphene sheets not only form a compact and uniform coating layer throughout the LFP NPs, but also stretch out and cross-link into a conducting network around the LFP particles. The LiFePO4@graphene composite displays a high reversible specific capacity of 167.7 mAh g-1 at 0.1C rate, superb rate performance with discharge capacity of 94.3 mAh g-1 at 100C rate and much prolonged cycle life. The remarkable electrochemical improvement is attributed to both electric and ionic conductivity increase as a result of in-situ grown graphene coatings along the LFP surface and the graphene network intrinsically connecting to the LFP particles.

Etched Colloidal LiFePO4 Nanoplatelets toward High-Rate Capable Li-Ion Battery Electrodes

PubMed Central

2014-01-01

LiFePO4 has been intensively investigated as a cathode material in Li-ion batteries, as it can in principle enable the development of high power electrodes. LiFePO4, on the other hand, is inherently “plagued” by poor electronic and ionic conductivity. While the problems with low electron conductivity are partially solved by carbon coating and further by doping or by downsizing the active particles to nanoscale dimensions, poor ionic conductivity is still an issue. To develop colloidally synthesized LiFePO4 nanocrystals (NCs) optimized for high rate applications, we propose here a surface treatment of the NCs. The particles as delivered from the synthesis have a surface passivated with long chain organic surfactants, and therefore can be dispersed only in aprotic solvents such as chloroform or toluene. Glucose that is commonly used as carbon source for carbon-coating procedure is not soluble in these solvents, but it can be dissolved in water. In order to make the NCs hydrophilic, we treated them with lithium hexafluorophosphate (LiPF6), which removes the surfactant ligand shell while preserving the structural and morphological properties of the NCs. Only a roughening of the edges of NCs was observed due to a partial etching of their surface. Electrodes prepared from these platelet NCs (after carbon coating) delivered a capacity of ∼155 mAh/g, ∼135 mAh/g, and ∼125 mAh/g, at 1 C, 5 C, and 10 C, respectively, with significant capacity retention and remarkable rate capability. For example, at 61 C (10.3 A/g), a capacity of ∼70 mAh/g was obtained, and at 122 C (20.7 A/g), the capacity was ∼30 mAh/g. The rate capability and the ease of scalability in the preparation of these surface-treated nanoplatelets make them highly suitable as electrodes in Li-ion batteries. PMID:25372361

Etched colloidal LiFePO4 nanoplatelets toward high-rate capable Li-ion battery electrodes.

PubMed

Paolella, Andrea; Bertoni, Giovanni; Marras, Sergio; Dilena, Enrico; Colombo, Massimo; Prato, Mirko; Riedinger, Andreas; Povia, Mauro; Ansaldo, Alberto; Zaghib, Karim; Manna, Liberato; George, Chandramohan

2014-12-10

LiFePO4 has been intensively investigated as a cathode material in Li-ion batteries, as it can in principle enable the development of high power electrodes. LiFePO4, on the other hand, is inherently "plagued" by poor electronic and ionic conductivity. While the problems with low electron conductivity are partially solved by carbon coating and further by doping or by downsizing the active particles to nanoscale dimensions, poor ionic conductivity is still an issue. To develop colloidally synthesized LiFePO4 nanocrystals (NCs) optimized for high rate applications, we propose here a surface treatment of the NCs. The particles as delivered from the synthesis have a surface passivated with long chain organic surfactants, and therefore can be dispersed only in aprotic solvents such as chloroform or toluene. Glucose that is commonly used as carbon source for carbon-coating procedure is not soluble in these solvents, but it can be dissolved in water. In order to make the NCs hydrophilic, we treated them with lithium hexafluorophosphate (LiPF6), which removes the surfactant ligand shell while preserving the structural and morphological properties of the NCs. Only a roughening of the edges of NCs was observed due to a partial etching of their surface. Electrodes prepared from these platelet NCs (after carbon coating) delivered a capacity of ∼ 155 mAh/g, ∼ 135 mAh/g, and ∼ 125 mAh/g, at 1 C, 5 C, and 10 C, respectively, with significant capacity retention and remarkable rate capability. For example, at 61 C (10.3 A/g), a capacity of ∼ 70 mAh/g was obtained, and at 122 C (20.7 A/g), the capacity was ∼ 30 mAh/g. The rate capability and the ease of scalability in the preparation of these surface-treated nanoplatelets make them highly suitable as electrodes in Li-ion batteries.

Aquifer recharge from infiltration basins in a highly urbanized area: the river Po Plain (Italy)

NASA Astrophysics Data System (ADS)

Masetti, M.; Nghiem, S. V.; Sorichetta, A.; Stevenazzi, S.; Santi, E. S.; Pettinato, S.; Bonfanti, M.; Pedretti, D.

2015-12-01

Due to the extensive urbanization in the Po Plain in northern Italy, rivers need to be managed to alleviate flooding problems while maintaining an appropriate aquifer recharge under an increasing percentage of impermeable surfaces. During the PO PLain Experiment field campaign in July 2015 (POPLEX 2015), both active and under-construction infiltration basins have been surveyed and analyzed to identify appropriate satellite observations that can be integrated to ground based monitoring techniques. A key strategy is to have continuous data time series on water presence and level within the basin, for which ground based monitoring can be costly and difficult to be obtained consistently.One of the major and old infiltration basin in the central Po Plain has been considered as pilot area. The basin is active from 2003 with ground based monitoring available since 2009 and supporting the development of a calibrated unsaturated-saturated two-dimensional numerical model simulating the infiltration dynamics through the basin.A procedure to use satellite data to detect surface water change is under development based on satellite radar backscatter data with an appropriate incidence angle and polarization combination. An advantage of satellite radar is that it can observe surface water regardless of cloud cover, which can be persistent during rainy seasons. Then, the surface water change is correlated to the reservoir water stage to determine water storage in the basin together with integrated ground data and to give quantitative estimates of variations in the local water cycle.We evaluated the evolution of the infiltration rate, to obtain useful insights about the general recharge behavior of basins that can be used for informed design and maintenance. Results clearly show when the basin becomes progressively clogged by biofilms that can reduce the infiltration capacity of the basin by as much as 50 times compared to when it properly works under clean conditions.

Ag{sub 3}PO{sub 4}/ZnO: An efficient visible-light-sensitized composite with its application in photocatalytic degradation of Rhodamine B

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Wei; School of Chemistry and Material Science, Huaibei Normal University, Huaibei 235000; Wang, Mingliang, E-mail: wangmlchem@263.net

2013-01-15

Graphical abstract: The free OH radicals generated in the VB of ZnO play the primary role in the visible-light photocatalytic degradation of RhB in Ag{sub 3}PO{sub 4}/ZnO system. The accumulated electrons in the CB of Ag{sub 3}PO{sub 4} can be transferred to O{sub 2} adsorbed on the surface of the composite semiconductors and H{sub 2}O{sub 2} yields. H{sub 2}O{sub 2} reacts with electrons in succession to produce active ·OH to some extent. Display Omitted Highlights: ► Efficient visible-light-sensitized Ag{sub 3}PO{sub 4}/ZnO composites were successfully prepared. ► Effect of Ag{sub 3}PO{sub 4} content on the catalytic activity of Ag{sub 3}PO{sub 4}/ZnOmore » is studied in detail. ► Rate constant of RhB degradation over Ag{sub 3}PO{sub 4}(3.0 wt.%)/ZnO is 3 times that of Ag{sub 3}PO{sub 4}. ► The active species in RhB degradation are examined by adding a series of scavengers. ► Visible light degradation mechanism of RhB over Ag{sub 3}PO{sub 4}/ZnO is systematically studied. -- Abstract: The efficient visible-light-sensitized Ag{sub 3}PO{sub 4}/ZnO composites with various weight percents of Ag{sub 3}PO{sub 4} were prepared by a facile ball milling method. The photocatalysts were characterized by XRD, DRS, SEM, EDS, XPS, and BET specific area. The ·OH radicals produced during the photocatalytic reaction was detected by the TA–PL technique. The photocatalytic property of Ag{sub 3}PO{sub 4}/ZnO was evaluated by photocatalytic degradation of Rhodamine B under visible light irradiation. Significantly, the results revealed that the photocatalytic activity of the composites was much higher than that of pure Ag{sub 3}PO{sub 4} and ZnO. The rate constant of RhB degradation over Ag{sub 3}PO{sub 4}(3.0 wt.%)/ZnO is 3 times that of single-phase Ag{sub 3}PO{sub 4}. The optimal percentage of Ag{sub 3}PO{sub 4} in the composite is 3.0 wt.%. It is proposed that the ·OH radicals produced in the valence band of ZnO play the leading role in the photocatalytic degradation of Rhodamine B by Ag{sub 3}PO{sub 4}/ZnO systems under visible light irradiation.« less

Two sympatric types of Plasmodium ovale and discrimination by molecular methods.

PubMed

Zaw, Myo Thura; Lin, Zaw

2017-10-01

Plasmodium ovale is widely distributed in tropical countries, whereas it has not been reported in the Americas. It is not a problem globally because it is rarely detected by microscopy owing to low parasite density, which is a feature of clinical ovale malaria. P.o. curtisi and P.o. wallikeri are widespread in both Africa and Asia, and were known to be sympatric in many African countries and in southeast Asian countries. Small subunit ribosomal RNA (SSUrRNA) gene, cytochrome b (cytb) gene, and merozoite surface protein-1 (msp-1) gene were initially studied for molecular discrimination of P.o. curtisi and P.o. wallikeri using polymerase chain reaction (PCR) and DNA sequencing. DNA sequences of other genes from P. ovale in Southeast Asia and the southwestern Pacific regions were also targeted to differentiate the two sympatric types. In terms of clinical manifestations, P.o. wallikeri tended to produce higher parasitemia levels and more severe symptoms. To date, there have been a few studies that used the quantitative PCR method for discrimination of the two distinct P. ovale types. Conventional PCR with consequent DNA sequencing is the common method used to differentiate these two types. It is necessary to identify these two types because relapse periodicity, drug susceptibility, and mosquito species preference need to be studied to reduce ovale malaria. In this article, an easier method of molecular-level discrimination of P.o. curtisi and P.o. wallikeri is proposed. Copyright © 2016. Published by Elsevier B.V.

77 FR 6091 - Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-07

...; Comment Request AGENCY: Defense Finance and Accounting Service, DoD. ACTION: Notice. SUMMARY: In... Accounting Service announces a proposed public information collection and seeks public comment on the... Accounting Service--Cleveland, P.O. Box 998002, Cleveland, OH 44199-8002; or call Mr. Scott Lafferty at (216...

78 FR 67339 - Initial Patent Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-12

... collection; Extension of Comment Period. SUMMARY: The United States Patent and Trademark Office (USPTO), as... Information Officer, United States Patent and Trademark Office, P.O. Box 1450, Alexandria, VA 22313-1450... to take this opportunity to comment on the revision of a continuing information collection. DATES...

Multiscale and multimodality computed tomography for cortical bone analysis

NASA Astrophysics Data System (ADS)

Ostertag, A.; Peyrin, F.; Gouttenoire, P. J.; Laredo, J. D.; DeVernejoul, M. C.; Cohen Solal, M.; Chappard, C.

2016-12-01

In clinical studies, high resolution peripheral quantitative computed tomography (HR-pQCT) is used to separately evaluate cortical bone and trabecular bone with an isotropic voxel of 82 µm3, and typical cortical parameters are cortical density (D.comp), thickness (Ct.Th), and porosity (Ct.Po). In vitro, micro-computed tomography (micro-CT) is used to explore the internal cortical bone micro-structure with isotropic voxels and high resolution synchrotron radiation (SR); micro-CT is considered the ‘gold standard’. In 16 tibias and 8 femurs, HR-pQCT measurements were compared to conventional micro-CT measurements. To test modality effects, conventional micro-CT measurements were compared to SR micro-CT measurements at 7.5 µm3 SR micro-CT measurements were also tested at different voxel sizes for the femurs, specifically, 7.5 µm3 versus 2.8 µm3. D.comp (r  =  -0.88, p  <  10-3) was the parameter best correlated with porosity (Po.V/TV). The correlation was not affected by the removal of pores under 130 µm. Ct.Th was also significantly highly correlated (r  =  -0.89 p  <  10-3), while Ct.Po was correlated with its counterpart Po.V/TV (r  =  0.74, p  <  10-3). From SR micro-CT and conventional micro-CT at 7.5 µm3 in matching areas, Po.V/TV and pore diameter were underestimated in conventional micro-CT with mean  ±  standard deviation (SD) biases of  -2.5  ±  1.9% and  -0.08  ±  0.08 mm, respectively. In contrast, pore number (Po.N) and pore separation (Po.Sp) were overestimated with mean  ±  SD biases of  +0.03  ±  0.04 mm-1 and  +0.02  ±  0.04 mm, respectively. The results from the tibia and femur were similar when the results of SR micro-CT at 7.5 µm3 and 2.8 µm3 were compared. Po.V/TV, specific surface of pores (Po.S/Po.V), and Po.N were underestimated with mean biases of  -1.7  ±  0.9%, -4.6  ±  4.4 mm-1, and  -0.26  ±  0.15 mm-1, respectively. In contrast, pore spacing was overestimated at 7.5 µm3 compared to 2.8 µm3 with mean biases of 0.05  ±  0.03 mm. Cortical bone measurements from HR-pQCT images provided consistent results compared to those obtained using conventional micro-CT at the distal tibia. D.comp was highly correlated to Po.V/TV because it considers both the micro-porosity (Haversian systems) and macro-porosity (resorption lacunae) of cortical bone. The complexity of canal organization, (including shape, connectivity, and surface) are not fully considered in conventional micro-CT in relation to beam hardening and cone beam reconstruction artifacts. With the exception of Po.V/TV measurements, morphological and topological measurements depend on the characteristics of the x-ray beam, and to a lesser extent, on image resolution.

Electrochemiluminescence quenching of luminol by CuS in situ grown on reduced graphene oxide for detection of N-terminal pro-brain natriuretic peptide.

PubMed

Li, Xiaojian; Lu, Peng; Wu, Bin; Wang, Yaoguang; Wang, Huan; Du, Bin; Pang, Xuehui; Wei, Qin

2018-07-30

A novel electrochemiluminescence (ECL) signal-off strategy based on CuS in situ grown on reduced graphene oxide (CuS-rGO) quenching luminol/H 2 O 2 system was firstly proposed. Luminol was grafted on the surface of Au@Fe 3 O 4 -Cu 3 (PO 4 ) 2 nanoflowers (Luminol-Au@Fe 3 O 4 -Cu 3 (PO 4 ) 2 ) which exhibited excellent catalytic effect towards the reduction of H 2 O 2 to enhance the ECL intensity of luminol. Cu 3 (PO 4 ) 2 nanoflowers showed large surface area which can immobilize more Fe 3 O 4 and Au nanoparticles. The quenching mechanism of CuS-rGO was due to ECL resonance energy transfer (RET). The spectral overlap between fluorescence spectrum of Luminol-Au@Fe 3 O 4 -Cu 3 (PO 4 ) 2 and UV-vis absorption spectrum of CuS-rGO revealed that resonance energy transfer was possible. Au nanoparticles were immobilized on the surface of CuS-rGO to capture secondary antibodies. After a sandwich-type immunoreaction, a remarkable decrease of ECL signal was observed. Under the optimal conditions, the immunosensor showed excellent performance for N-terminal pro-brain natriuretic peptide (NT-proBNP) detection with a wide detection range from 0.5 pg mL -1 to 20 ng mL -1 and a low detection limit of 0.12 pg mL -1 (S/N = 3). The prepared NT-proBNP immunosensor displayed high sensitivity, excellent stability and good specificity. Copyright © 2018 Elsevier B.V. All rights reserved.

Thin film rechargeable electrodes based on conductive blends of nanostructured olivine LiFePO4 and sucrose derived nanocarbons for lithium ion batteries.

PubMed

Praveen, P; Jyothsna, U; Nair, Priya; Ravi, Soumya; Balakrishnan, A; Subramanian, K R V; Nair, A Sreekumaran; Nair, V Shantikumar; Sivakumar, N

2013-08-01

The present study provides the first reports of a novel approach of electrophoretic co-deposition technique by which titanium foils are coated with LiFePO4-carbon nanocomposites synthesized by sol gel route and processed into high-surface area cathodes for lithium ion batteries. The study elucidates how sucrose additions as carbon source can affect the surface morphology and the redox reaction behaviors underlying these cathodes and thereby enhance the battery performance. The phase and morphological analysis were done using XRD and XPS where the LiFePO4 formed was confirmed to be a high purity orthorhombic system. From the analysis of the relevant electrochemical parameters using cyclic voltammetry and electrochemical impedance spectroscopy, a 20% increment and 90% decrement in capacity and impedance values were observed respectively. The composite electrodes also exhibited a specific capacity of 130 mA h/g. It has been shown that cathodes based on such composite systems can allow significant room for improvement in the cycling performance at the electrode/electrolyte interface.

Opposite effect of photocorrosion on photocatalytic performance among various AgxMyOz/TiO2 (M = C, P) photocatalysts: A novel effective method for preparing Ag/TiO2 composite

NASA Astrophysics Data System (ADS)

Feng, Caixia; Pang, Yuhua; Wang, Yan; Sun, Mingming; Zhang, Chenyan; Zhang, Ling; Zhou, Yanmei; Li, Deliang

2016-07-01

Three kinds of hybrids, Ag2CO3/TiO2, Ag2C2O4/TiO2 and Ag3PO4/TiO2 comprising of P25-TiO2 and silver-containing photocatalyst, (together coded as AgxMyOz/TiO2 (M = C, P)) were prepared via a facile precipitation method. The photocatalytic activity and stability of the as-prepared AgxMyOz/TiO2 was compared by monitoring the oxidation of propylene under visible light irradiation. Results showed that both Ag2CO3/TiO2 and Ag2C2O4/TiO2 exhibit perfect performance with a high propylene degradation removal rate of 88% and 78%, respectively, during four successive experimental runs. On the contrary, for Ag3PO4/TiO2, the photocatalytic activity gradually declines to 8% from 32% under the same conditions. In order to explore the reason for the above remarkable difference in activity and stability over AgxMyOz/TiO2, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and UV-vis diffuse reflectance spectroscopy (DRS) were used to investigate the change of AgxMyOz/TiO2 before and after irradiation. It was found that three silver-containings, Ag2CO3, Ag2C2O4 and Ag3PO4 on the surface of TiO2, all experienced photo-corrosion to various extents during irradiation process. Surprisingly, the effect of photo-corrosion on visible light activity and stability among various AgxMyOz/TiO2 is very different. For both Ag2CO3 and Ag2C2O4, they are easily decomposed into metallic Ag and CO2, and gaseous CO2 escaped from catalyst leaving silver nanoparticles on the surface of TiO2 resulted in the formation of plasmonic photocatalyst Ag/TiO2. The synergetic effect between surface plasma resonance of silver and interfacial electron transfer over the obtained Ag/TiO2 heterojunctions is in favor of the superior photocatalytic performance under visible light. While for Ag3PO4/TiO2, Ag3PO4 on the surface of TiO2 is partially photo-decomposed into Ag and phosphorus oxide and the phosphorus oxide covering on the surface of undecomposed Ag3PO4/TiO2 deactivates its photocatalytic performance. By comparison with the traditional Ag/TiO2 synthesized by photochemical reduction method, it was found that the photo-corrosion of Ag2CO3/TiO2 or Ag2C2O4/TiO2 can be used as a more effective method for preparing Ag/TiO2 composite.

Backscatter analysis of dihedral corner reflectors using physical optics and the physical theory of diffraction

NASA Technical Reports Server (NTRS)

Griesser, Timothy; Balanis, Constantine A.

1987-01-01

The backscatter cross-sections of dihedral corner reflectors in the azimuthal plane are presently determined by both physical optics (PO) and the physical theory of diffraction (PTD), yielding results for the vertical and horizontal polarizations. In the first analysis method used, geometrical optics is used in place of PO at initial reflections in order to maintain the planar character of the reflected wave and reduce the complexity of the analysis. In the second method, PO is used at almost every reflection in order to maximize the accuracy of the PTD solution at the expense of a rapid increase in complexity. Induced surface current densities and resulting cross section patterns are illustrated for the two methods.

Porous texture of activated carbons prepared by phosphoric acid activation of woods

NASA Astrophysics Data System (ADS)

Díaz-Díez, M. A.; Gómez-Serrano, V.; Fernández González, C.; Cuerda-Correa, E. M.; Macías-García, A.

2004-11-01

Activated carbons (ACs) have been prepared using chestnut, cedar and walnut wood shavings from furniture industries located in the Comunidad Autónoma de Extremadura (SW Spain). Phosphoric acid (H3PO4) at different concentrations (i.e. 36 and 85 wt.%) has been used as activating agent. ACs have been characterized from the results obtained by N2 adsorption at 77 K. Moreover, the fractal dimension (D) has been calculated in order to determine the AC surface roughness degree. Optimal textural properties of ACs have been obtained by chemical activation with H3PO4 36 wt.%. This is corroborated by the slightly lower values of D for samples treated with H3PO4 85 wt.%.

Oxygen transport and pyrite oxidation in unsaturated coal-mine spoil

USGS Publications Warehouse

Guo, Weixing; Cravotta, Charles A.

1996-01-01

An understanding of the mechanisms of oxygen (02) transport in unsaturated mine spoil is necessary to design and implement effective measures to exclude 02 from pyritic materials and to control the formation of acidic mine drainage. Partial pressure of oxygen (Po2) in pore gas, chemistry of pore water, and temperature were measured at different depths in unsaturated spoil at two reclaimed surface coal mines in Pennsylvania. At mine 1, where spoil was loose, blocky sandstone, Po2 changed little with depth, decreasing from 21 volume percent (vol%) at the ground surface to a minimum of about 18 vol% at 10 m depth. At mine 2, where spoil was compacted, friable shale, Po2 decreased to less than 2 vol% at depth of about 10 m. Although pore-water chemistry and temperature data indicate that acid-forming reactions were active at both mines, the pore-gas data indicate that mechanisms for 0 2 transport were different at each mine. A numerical model was developed to simulate 02 transport and pyrite oxidation in unsaturated mine spoil. The results of the numerical simulations indicate that differences in 02 transport at the two mines can be explained by differences in the air permeability of spoil. Po2 changes little with depth if advective transport of 02 dominates as at mine 1, but decreases greatly with depth if diffusive transport of 02 dominates, as in mine 2. Model results also indicate that advective transport becomes significant if the air permeability of spoil is greater than 10-9 m2, which is expected for blocky sandstone spoil. In the advective-dominant system, thermally-induced convective air flow, as a consequence of the exothermic oxidation of pyrite, supplies the 02 to maintain high Po2 within the deep unsaturated zone.

Complex community of nitrite-dependent anaerobic methane oxidation bacteria in coastal sediments of the Mai Po wetland by PCR amplification of both 16S rRNA and pmoA genes.

PubMed

Chen, Jing; Zhou, Zhichao; Gu, Ji-Dong

2015-02-01

In the present work, both 16S rRNA and pmoA gene-based PCR primers were employed successfully to study the diversity and distribution of n-damo bacteria in the surface and lower layer sediments at the coastal Mai Po wetland. The occurrence of n-damo bacteria in both the surface and subsurface sediments with high diversity was confirmed in this study. Unlike the two other known n-damo communities from coastal areas, the pmoA gene-amplified sequences in the present work clustered not only with some freshwater subclusters but also within three newly erected marine subclusters mostly, indicating the unique niche specificity of n-damo bacteria in this wetland. Results suggested vegetation affected the distribution and community structures of n-damo bacteria in the sediments and n-damo could coexist with sulfate-reducing methanotrophs in the coastal ecosystem. Community structures of the Mai Po n-damo bacteria based on 16S rRNA gene were different from those of either the freshwater or the marine. In contrast, structures of the Mai Po n-damo communities based on pmoA gene grouped with the marine ones and were clearly distinguished from the freshwater ones. The abundance of n-damo bacteria at this wetland was quantified using 16S rRNA gene PCR primers to be 2.65-6.71 × 10(5) copies/g dry sediment. Ammonium and nitrite strongly affected the community structures and distribution of n-damo bacteria in the coastal Mai Po wetland sediments.

Accounting for oxygen in the renal cortex: a computational study of factors that predispose the cortex to hypoxia.

PubMed

Lee, Chang-Joon; Gardiner, Bruce S; Ngo, Jennifer P; Kar, Saptarshi; Evans, Roger G; Smith, David W

2017-08-01

We develop a pseudo-three-dimensional model of oxygen transport for the renal cortex of the rat, incorporating both the axial and radial geometry of the preglomerular circulation and quantitative information regarding the surface areas and transport from the vasculature and renal corpuscles. The computational model was validated by simulating four sets of published experimental studies of renal oxygenation in rats. Under the control conditions, the predicted cortical tissue oxygen tension ([Formula: see text]) or microvascular oxygen tension (µPo 2 ) were within ±1 SE of the mean value observed experimentally. The predicted [Formula: see text] or µPo 2 in response to ischemia-reperfusion injury, acute hemodilution, blockade of nitric oxide synthase, or uncoupling mitochondrial respiration, were within ±2 SE observed experimentally. We performed a sensitivity analysis of the key model parameters to assess their individual or combined impact on the predicted [Formula: see text] and µPo 2 The model parameters analyzed were as follows: 1 ) the major determinants of renal oxygen delivery ([Formula: see text]) (arterial blood Po 2 , hemoglobin concentration, and renal blood flow); 2 ) the major determinants of renal oxygen consumption (V̇o 2 ) [glomerular filtration rate (GFR) and the efficiency of oxygen utilization for sodium reabsorption (β)]; and 3) peritubular capillary surface area (PCSA). Reductions in PCSA by 50% were found to profoundly increase the sensitivity of [Formula: see text] and µPo 2 to the major the determinants of [Formula: see text] and V̇o 2 The increasing likelihood of hypoxia with decreasing PCSA provides a potential explanation for the increased risk of acute kidney injury in some experimental animals and for patients with chronic kidney disease. Copyright © 2017 the American Physiological Society.

Effect on lipopolysaccharide structure of aeration during growth of a plum isolate of Pseudomonas syringae pv. morsprunorum.

PubMed

Smith, A R; Munro, S M; Wait, R; Hignett, R C

1994-07-01

The composition of lipopolysaccharide (LPS) extracted with aqueous phenol from a virulent English plum isolate of Pseudomonas syringae pv. morsprunorum varied according to the partial pressure of oxygen (pO2) in the culture medium at the time of harvest. When pO2 was low, the organism grew slowly and produced smooth LPS bearing rhamnan sidechains. As pO2 was raised, the rate of growth increased and smooth LPS was replaced by a rough species deficient in rhamnose, which co-extracted with a D-glucan. Organization of rhamnose and glucose into separate polymers was shown by the selective susceptibility of the rhamnose-containing polymer to hydrolysis by rhamnanase of the phage A7. By methylation analysis, GC-MS, and 1H- and 13C-NMR spectroscopy, the glucan was shown to consist of alpha (1-->4)-linked residues with alpha (1-->4,6)-branch points and non-reducing terminal residues in the approximate ratio 4:1:1, resembling glycogen in composition. A glucan which co-extracted with LPS using phenol/water from an avirulent plum isolate that was resistant to lysis by phages A1 and A7 was shown by methylation analysis to have a similar structure. Whether the effect on LPS composition was due directly to pO2, or was dependent on the rate of growth, has not been established. It is suggested that, because epiphytic growth would entail exposure to high pO2, English plum isolates growing on the surfaces of host plants might be unable to produce smooth LPS. Since cell surface composition affects virulence in plant-pathogenic pseudomonads, this effect could account for the observed failure of the English plum isolates to enter the host via leaf scars.

First measurement of surface nuclear recoil background for argon dark matter searches

DOE PAGES

Xu, Jingke; Stanford, Chris; Westerdale, Shawn; ...

2017-09-19

Here, one major background in direct searches for weakly interacting massive particles (WIMPs) comes from the deposition of radon progeny on detector surfaces. A dangerous surface background is the 206Pb nuclear recoils produced by 210Po decays. In this paper, we report the first characterization of this background in liquid argon. The scintillation signal of low energy Pb recoils is measured to be highly quenched in argon, and we estimate that the 103 keV 206Pb recoil background will produce a signal equal to that of a ~5 keV (30 keV) electron recoil ( 40Ar recoil). In addition, we demonstrate that thismore » dangerous 210Po surface background can be suppressed, using pulse shape discrimination methods, by a factor of ~100 or higher, which can make argon dark matter detectors near background-free and enhance their potential for discovery of medium- and high-mass WIMPs. Lastly, we also discuss the impact on other low background experiments.« less

Primate polonium metabolic models and their use in estimation of systemic radiation doses from bioassay data. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cohen, N.

1989-03-15

A Polonium metabolic model was derived and incorporated into a Fortran algorithm which estimates the systemic radiation dose from {sup 210}Po when applied to occupational urine bioassay data. The significance of the doses estimated are examined by defining the degree of uncertainty attached to them through comprehensive statistical testing procedures. Many parameters necessary for dosimetry calculations (such as organ partition coefficients and excretion fractions), were evaluated from metabolic studies of {sup 210}Po in non-human primates. Two tamarins and six baboons were injected intravenously with {sup 210}Po citrate. Excreta and blood samples were collected. Five of the baboons were sacrificed atmore » times ranging from 1 day to 3 months post exposure. Complete necropsies were performed and all excreta and the majority of all skeletal and tissue samples were analyzed radiochemically for their {sup 210}Po content. The {sup 210}Po excretion rate in the baboon was more rapid than in the tamarin. The biological half-time of {sup 210}Po excretion in the baboon was approximately 15 days while in the tamarin, the {sup 210}Po excretion rate was in close agreement with the 50 day biological half-time predicted by ICRP 30. Excretion fractions of {sup 210}Po in the non-human primates were found to be markedly different from data reported elsewhere in other species, including man. A thorough review of the Po urinalysis procedure showed that significant recovery losses resulted when metabolized {sup 210}Po was deposited out of raw urine. Polonium-210 was found throughout the soft tissues of the baboon but not with the partition coefficients for liver, kidneys, and spleen that are predicted by the ICRP 30 metabolic model. A fractional distribution of 0.29 for liver, 0.07 for kidneys, and 0.006 for spleen was determined. Retention times for {sup 210}Po in tissues are described by single exponential functions with biological half-times ranging from 15 to 50 days.« less

Preliminary Results from a Survey of DPS Scientist’s Attitudes, Activities and Needs in Education and Public Outreach

NASA Astrophysics Data System (ADS)

Grier, Jennifer A.; Buxner, Sanlyn; Schneider, Nick

2014-11-01

The NASA SMD Planetary Sciences Forum, in partnership with the AAS DPS Education officer has conducted a semi-structured series of interviews with two-dozen DPS members to ascertain: the nature E/PO activities pursued by scientists, what resources and professional development opportunities are needed by scientists, how to increase the impact of scientists’ E/PO efforts, scientists’ concerns and questions regarding E/PO, and what we can do to identify opportunities to address these issues, both from the SMD and DPS perspectives. Members were contacted by phone, and responded to a loose script of questions over a time span of 20 to 90 minutes, depending on the individual. Members were chosen to represent a variety of career experience, home institutions and affiliations, and level of involvement with E/PO. Questions included: What is your level of involvement in E/PO? What sort of professional development or resources would you like to have to increase the efficiency of your E/PO efforts? What barriers to E/PO involvement have you encountered? How do you use social media in your E/PO efforts, if at all? What are your motivations for involvement in E/PO? etc. Our results are consistent with previous research conducted regarding this issue, but they do offer insight specific to the nature of DPS members and their views about E/PO. We will present a subset of these results, the opportunities they present, and the responses of both the PS Forum and the DPS. Based on this survey, the SMD PS Forum was able to identify specific new resources needed by scientists, and therefore developed the brief-one page guides, “The Quick Introduction to Education and Public Outreach,” and “Making the Most of Your E/PO Time - Increasing Your Efficiency and Impact.” Further resources and professional development opportunities will be developed as the data continue to be reviewed. This data collection effort is ongoing. If you would like to become involved, contact Jennifer Grier, jgrier@psi.edu.

Impact of Partial Pressure of Oxygen in Blood Samples on the Performance of Systems for Self-Monitoring of Blood Glucose

PubMed Central

Baumstark, Annette; Pleus, Stefan; Haug, Cornelia; Tesar, Martina; Freckmann, Guido

2014-01-01

Abstract Background: The partial pressure of oxygen (pO2) in blood samples can affect glucose measurements with oxygen-sensitive systems. In this study, we assessed the influence of different pO2 levels on blood glucose (BG) measurements with five glucose oxidase (GOD) systems and one glucose dehydrogenase (GDH) system. All selected GOD systems were indicated by the manufacturers to be sensitive to increased oxygen content of the blood sample. Materials and Methods: Venous blood samples of 16 subjects (eight women, eight men; mean age, 52 years; three with type 1 diabetes, four with type 2 diabetes, and nine without diabetes) were collected. Aliquots of each sample were adjusted to the following pO2 values: ≤45 mm Hg, approximately 70 mm Hg, and ≥150 mm Hg. For each system, five consecutive measurements on each sample were performed using the same test strip lot. Relative differences between the mean BG value at a pO2 level of approximately 70 mm Hg, which was considered to be similar to pO2 values in capillary blood samples, and the mean BG value at pO2 levels ≤45 mm Hg and ≥150 mm Hg were calculated. Results: The GOD systems showed mean relative differences between 11.8% and 44.5% at pO2 values ≤45 mm Hg and between −14.6% and −21.2% at pO2 values ≥150 mm Hg. For the GDH system, the mean relative differences were −0.3% and −0.2% at pO2 values ≤45 mm Hg and ≥150 mm Hg, respectively. Conclusions: The magnitude of the pO2 impact on BG measurements seems to vary among the tested oxygen-sensitive GOD systems. The pO2 range in which oxygen-sensitive systems operate well should be provided in the product information. PMID:24205977

Electrochemical and kinetic studies of ultrafast laser structured LiFePO4 electrodes

NASA Astrophysics Data System (ADS)

Mangang, M.; Gotcu-Freis, P.; Seifert, H. J.; Pfleging, W.

2015-03-01

Due to a growing demand of cost-efficient lithium-ion batteries with an increased energy and power density as well as an increased life-time, the focus is set on intercalation cathode materials like LiFePO4. It has a high practical capacity, is environmentally friendly and has low material costs. However, its low electrical conductivity and low ionic diffusivity are major drawbacks for its use in electrochemical storage devices or electric vehicles. By adding conductive agents, the electrical conductivity can be enhanced. By increasing the surface of the cathode material which is in direct contact with the liquid electrolyte the lithium-ion diffusion kinetics can be improved. A new approach to increase the surface of the active material without changing the active particle packing density or the weight proportion of carbon black is the laser-assisted generation of 3D surface structures in electrode materials. In this work, ultrafast laser radiation was used to create a defined surface structure in LiFePO4 electrodes. It was shown that by using ultrashort laser pulses instead of nanosecond laser pulses, the ablation efficiency could be significantly increased. Furthermore, melting and debris formation were reduced. To investigate the diffusion kinetics, electrochemical methods such as cyclic voltammetry and galvanostatic intermittent titration technique were applied. It could be shown that due to a laser generated 3D structure, the lithium-ion diffusion kinetic, the capacity retention and cell life-time can be significantly improved.

Palmitic acid in the sn-2 position of dietary triacylglycerols does not affect insulin secretion or glucose homeostasis in healthy men and women.

PubMed

Filippou, A; Teng, K-T; Berry, S E; Sanders, T A B

2014-09-01

Dietary triacylglycerols containing palmitic acid in the sn-2 position might impair insulin release and increase plasma glucose. We used a cross-over designed feeding trial in 53 healthy Asian men and women (20-50 years) to test this hypothesis by exchanging 20% energy of palm olein (PO; control) with randomly interesterified PO (IPO) or high oleic acid sunflower oil (HOS). After a 2-week run-in period on PO, participants were fed PO, IPO and HOS for 6 week consecutively in randomly allocated sequences. Fasting (midpoint and endpoint) and postprandial blood at the endpoint following a test meal (3.54 MJ, 14 g protein, 85 g carbohydrate and 50 g fat as PO) were collected for the measurement of C-peptide, insulin, glucose, plasma glucose-dependent insulinotropic polypeptide and glucagon-like peptide-1, lipids and apolipoproteins; pre-specified primary and secondary outcomes were postprandial changes in C-peptide and plasma glucose. Low density lipoprotein cholesterol was 0.3 mmol/l (95% confidence interval (95% CI)) 0.1, 0.5; P<0.001) lower on HOS than on PO or IPO as predicted, indicating good compliance to the dietary intervention. There were no significant differences (P=0.58) between diets among the 10 male and 31 female completers in the incremental area under the curve (0-2 h) for C-peptide in nmol.120 min/l: GM (95% CI) were PO 220 (196, 245), IPO 212 (190, 235) and HOS 224 (204, 244). Plasma glucose was 8% lower at 2 h on IPO vs PO and HOS (both P<0.05). Palmitic acid in the sn-2 position does not adversely impair insulin secretion and glucose homeostasis.

Near-infrared (1550 nm) in vivo bioimaging based on rare-earth doped ceramic nanophosphors modified with PEG-b-poly(4-vinylbenzylphosphonate)

NASA Astrophysics Data System (ADS)

Kamimura, Masao; Kanayama, Naoki; Tokuzen, Kimikazu; Soga, Kohei; Nagasaki, Yukio

2011-09-01

A novel poly(ethylene glycol) (PEG)-based block copolymer possessing a 4-vinylbenzylphosphonate repeating unit in another segment (PEG-block-poly(4-vinylbenzylphosphonate)) (PEG-b-PVBP) was designed and successfully synthesized. As a control, an end-functionalized PEG possessing a mono-phosphonate group (PEG-PO3H2) was also synthesized. The surface of near-infrared (NIR) phosphors (i.e., ytterbium (Yb) and erbium (Er) ion-codoped Y2O3 nanoparticles (YNPs)) were modified with PEG-b-PVBP (PEG-YNP(b)s) and PEG-PO3H2 (PEG-YNP(1)s). The adsorption of PEG-b-PVBP and PEG-PO3H2 was estimated by Fourier transform infrared (FT-IR) measurements and thermal gravimetric analysis (TGA). The physicochemical characteristics of the obtained YNP samples were analyzed by ζ-potential and dynamic light scattering (DLS) measurements. The ζ-potentials of YNPs modified by these polymers were close to zero, indicating the effective coverage of the YNP surface by our new PEG derivatives. However, the dispersion stability of the PEGylated YNPs was strongly affected by the structure of the PEG terminus. The average diameter of the PEG-YNP(1)s increased, and aggregates precipitated after less than 1 h in phosphate buffer saline (PBS). In contrast, the size did not change at all in the case of PEG-YNP(b)s and the dispersion in PBS was stable for over 1 week. PEG-YNP(b)s also showed high erosion resistance under acidic conditions. The multiple coordinated PVBP segment of the block copolymer on the YNP surface plays a substantial role in improving such dispersion stability. The excellent dispersion stability and strong NIR luminescence of the obtained PEG-YNP(b)s were also confirmed in fetal bovine serum (FBS) solution over 1 week. Furthermore, in vivo NIR imaging of live mice was performed, and the 1550 nm NIR emission of PEG-YNP(b)s from the organ of live mice was confirmed without dissection.A novel poly(ethylene glycol) (PEG)-based block copolymer possessing a 4-vinylbenzylphosphonate repeating unit in another segment (PEG-block-poly(4-vinylbenzylphosphonate)) (PEG-b-PVBP) was designed and successfully synthesized. As a control, an end-functionalized PEG possessing a mono-phosphonate group (PEG-PO3H2) was also synthesized. The surface of near-infrared (NIR) phosphors (i.e., ytterbium (Yb) and erbium (Er) ion-codoped Y2O3 nanoparticles (YNPs)) were modified with PEG-b-PVBP (PEG-YNP(b)s) and PEG-PO3H2 (PEG-YNP(1)s). The adsorption of PEG-b-PVBP and PEG-PO3H2 was estimated by Fourier transform infrared (FT-IR) measurements and thermal gravimetric analysis (TGA). The physicochemical characteristics of the obtained YNP samples were analyzed by ζ-potential and dynamic light scattering (DLS) measurements. The ζ-potentials of YNPs modified by these polymers were close to zero, indicating the effective coverage of the YNP surface by our new PEG derivatives. However, the dispersion stability of the PEGylated YNPs was strongly affected by the structure of the PEG terminus. The average diameter of the PEG-YNP(1)s increased, and aggregates precipitated after less than 1 h in phosphate buffer saline (PBS). In contrast, the size did not change at all in the case of PEG-YNP(b)s and the dispersion in PBS was stable for over 1 week. PEG-YNP(b)s also showed high erosion resistance under acidic conditions. The multiple coordinated PVBP segment of the block copolymer on the YNP surface plays a substantial role in improving such dispersion stability. The excellent dispersion stability and strong NIR luminescence of the obtained PEG-YNP(b)s were also confirmed in fetal bovine serum (FBS) solution over 1 week. Furthermore, in vivo NIR imaging of live mice was performed, and the 1550 nm NIR emission of PEG-YNP(b)s from the organ of live mice was confirmed without dissection. Electronic supplementary information (ESI) available: 1H-NMR spectra of PEG-b-PCMS, PEG-b-PDEVBP and PEG-b-PVBP, 31P-NMR spectra of PEG-b-PDEVBP and PEG-b-PVBP, schematic representation of PEG-PO3H2 synthesis, 1H-NMR spectra of PEG-PO3Et2 and PEG-PO3H2, FT-IR spectra of YNP samples, PEG brush density on the YNP surface, and size distribution of YNP samples under acidic conditions are described. See DOI: 10.1039/c1nr10466g

Activity and physiological significance of the pleopods in the respiration of Callianassa californiensis (Dana) (Crustacea: Thalassinidea).

PubMed

Torres, J J; Gluck, D L; Childress, J J

1977-02-01

1. The pleopods of C. californiensis, a potential site for extrabranchial oxygen exchange, do not contribute significantly to oxygen consumption. 2. C. californiensis has a gill surface area of 4.13 +/- 0.72 cm2/g wet body weight, the lowest value yet reported for a totally aquatic crustacean. 3. C. californiensis, when placed in simulated burrow conditions, regulates the PO2 very loosely in its immediate microhabitat, using its pleopods. 4. Field studies of pH and PO2 values in burrows of C. californiensis indicate that animal movement may play a large part in water exchange between the surface and burrow. 5. Activity studies suggest that oxygen is not critical to C. californiensis on a short term basis. Perception of oxygen after long deprivation may signal the possibility of renewed feeding and activity at the surface of its burrow.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Jingke; Stanford, Chris; Westerdale, Shawn

Here, one major background in direct searches for weakly interacting massive particles (WIMPs) comes from the deposition of radon progeny on detector surfaces. A dangerous surface background is the 206Pb nuclear recoils produced by 210Po decays. In this paper, we report the first characterization of this background in liquid argon. The scintillation signal of low energy Pb recoils is measured to be highly quenched in argon, and we estimate that the 103 keV 206Pb recoil background will produce a signal equal to that of a ~5 keV (30 keV) electron recoil ( 40Ar recoil). In addition, we demonstrate that thismore » dangerous 210Po surface background can be suppressed, using pulse shape discrimination methods, by a factor of ~100 or higher, which can make argon dark matter detectors near background-free and enhance their potential for discovery of medium- and high-mass WIMPs. Lastly, we also discuss the impact on other low background experiments.« less

Engaging Scientists in NASA Education and Public Outreach: Tools for Scientist Engagement

NASA Astrophysics Data System (ADS)

Buxner, Sanlyn; Meinke, B. K.; Hsu, B.; Shupla, C.; Grier, J. A.; E/PO Community, SMD

2014-01-01

The NASA Science Education and Public Outreach Forums support the NASA Science Mission Directorate (SMD) and its education and public outreach (E/PO) community through a coordinated effort to enhance the coherence and efficiency of SMD-funded E/PO programs. The Forums foster collaboration between scientists with content expertise and educators with pedagogy expertise. We present tools and resources to support astronomers’ engagement in E/PO efforts. Among the tools designed specifically for scientists are a series of one-page E/PO-engagement Tips and Tricks guides, a sampler of electromagnetic-spectrum-related activities, and NASA SMD Scientist Speaker’s Bureau (http://www.lpi.usra.edu/education/speaker). Scientists can also locate resources for interacting with diverse audiences through a number of online clearinghouses, including: NASA Wavelength, a digital collection of peer-reviewed Earth and space science resources for educators of all levels (http://nasawavelength.org), and EarthSpace (http://www.lpi.usra.edu/earthspace), a community website where faculty can find and share teaching resources for the undergraduate Earth and space sciences classroom. Learn more about the opportunities to become involved in E/PO and to share your science with students, educators, and the general public at http://smdepo.org.

EXAFS Study on LiFePO4 Powders Produced From Two Sol-Gel Routes

NASA Astrophysics Data System (ADS)

Negara, V. S. I.; Latif, C.; Wongtepa, W.; Pratapa, S.

2018-04-01

The local structure of LiFePO4 powders has been investigated using Fe K-edge Extended X-Ray Absorption Fine Structure (EXAFS) Spectroscopy data. The synthesis of LFP powders was carried out using two different sol-gel methods. The raw materials for Fe source were ironstone and commercial precursor of FeCl2·4H2O. Synthesis using natural materials produced two phases, namely LiFePO4 olivine and Li3Fe2(PO4)3 nasicon, whereas that using a commercial product produced a single phase of LiFePO4 olivine. The EXAFS data for both samples were collected at Synchrotron Light Research Institute (SLRI), Thailand. Fitting of the model on the experimental curve provided parameters that can be interpreted as the distance between Fe as the absorber and the nearest atoms on the LFP materials. The EXAFS data analysis has shown that synthesis of LFPs using different Fe sources gives slightly different nearest-neighbor distances, namely Fe-O of 0.21% -0.23%, Fe-P of 0.14% - 0.16%, Fe-Fe of 0.12% for both samples, respectively.

Transfer of (40)K, (238)U, (210)Pb, and (210)Po from soil to plant in various locations in south of Syria.

PubMed

Al-Masri, M S; Al-Akel, B; Nashawani, A; Amin, Y; Khalifa, K H; Al-Ain, F

2008-02-01

Transfer factors of (40)K, (238)U, (210)Pb, and (210)Po from soil to some agriculture crops in various locations in south of Syria (Dara'a and Assuwaydaa districts) have been determined. Soil and vegetable crops (green pepper, cucumber, tomato, and eggplant), legumes crops (lentil, chickpea, and broad bean), fruit trees (apple, grape, and olives) and cereals (barley and wheat) were collected and analyzed for (238)U, (210)Pb, and (210)Po. The results have shown that higher transfer factors (calculated as Bqkg(-1) dry wt. plant material per Bqkg(-1) dry wt. soil) for (210)Po, (210)Pb and (238)U were observed in vegetable leaves than fruits and cereals leaves; the highest values of transfer factor (TF) for (238)U were found to be 0.1 for straw of chickpea. Transfer factors for (210)Po varied between 2.8x10(-2) and 2 in fruits of eggplant and grain of barley, respectively. In addition, several parameters affecting transfer factors of the radionuclides were evaluated. The results can be considered as base values for TF of natural radionuclides in the region.

Treatment of Explosives Residues From Range Activities

DTIC Science & Technology

2010-01-01

plus 5 kg crude soybean oil), while three plots served as controls and received no PMSO (designated CON ). PMSO was prepared by thoroughly mixing...compounds. The topmost layers of soil in the CON plots were removed in 1.25 cm lifts. The PMSO in the PO1 and PO2 plots was collected in two portions...soil plots ( CON -2) was not behaving the same as the other two control plots based on a careful assessment of several parameters, including higher

Observational constraints on projections of the ozone response to NOx controls in the Southern San Joaquin Valley

NASA Astrophysics Data System (ADS)

Pusede, S. E.; Wooldridge, P. J.; Browne, E. C.; Russell, A. R.; Rollins, A.; Min, K.; Thomas, J.; Zhang, L.; Brune, W. H.; Henry, S. B.; DiGangi, J. P.; Keutsch, F. N.; Sanders, J. E.; Ren, X.; Weber, R.; Goldstein, A. H.; Cohen, R. C.

2011-12-01

We investigate the impact of NOx reductions on ozone production in the Southern San Joaquin Valley using a large suite of radical and trace gas measurements collected during CalNex-2010 in Bakersfield, California (May 15-June 28) combined with the historical record of O3, nitrogen oxides and temperature from CARB monitoring sites in the region. We calculate the instantaneous ozone production rate (PO3) by radical balance and investigate relationships between PO3 and NOx abundance; finding temperature to be a useful proxy for VOC reactivity. We show Bakersfield photochemistry is at peak PO3 and therefore at a minimum with respect to the effectiveness of NOx controls indicating: (1) more than 30% reductions from present day are required before sizable decreases in ozone will occur and (2) reduction from the lower weekend baseline NOx concentrations will result in weekend PO3 decreases with continued NOx controls at high temperatures when VOC reactivity is largest.

LiFePO4 nanoparticles enveloped in freestanding sandwich-like graphitized carbon sheets as enhanced remarkable lithium-ion battery cathode.

PubMed

Zhang, Yan; Zhang, Huijuan; Li, Xiao; Xu, Haitao; Wang, Yu

2016-04-15

A novel nanostructure where LiFePO4 nanoparticles are enveloped in sandwich-like carbon sheets as an enhanced cathode in lithium-ion batteries has successfully been synthesized for the first time. Compared to previous carbon-based nanocomposites, the achieved sandwich-like LiFePO4 nanocomposites exhibit totally different architecture, in which LiFePO4 nanoparticles are tightly entrapped between two carbon layers, instead of being anchored on the carbon sheet surfaces. In other words, the achieved sandwich-like LiFePO4 nanocomposite carbon layers are actually freestanding and can be operated and separated from each other. This is a great breakthrough in the design and synthesis of carbon-based functional materials. The obtained sandwich-like LiFePO4 nanocomposites present excellent electrochemical performance, which is rationally ascribed to the superb and unique structure and architecture. Of particular note is that the freestanding sandwich-like LiFePO4 nanocomposites exhibit enhanced cyclability and rate capability. At a high current density of 0.1 A g(-1), a stable specific capacity of approximately 168.5 mAh g(-1) can be delivered over 1000 cycles, and when the charge-discharge rates increase to 0.6, 2, 5 and 10 A g(-1), the specific capacities still survive at 149, 129, 114 and 91 mAh g(-1), respectively. Meanwhile, the sandwiched nanocomposite demonstrates a significantly improved low-temperature electrochemical energy storage performance. With respect to the excellent Li storage performance, and facility and reliability of production, the freestanding sandwich-like LiFePO4 nanocomposites are reasonably believed to have a great potential for multiple electrochemical energy storage applications.

Increased exposure to pollutant aerosols under high voltage power lines.

PubMed

Fews, A P; Henshaw, D L; Keitch, P A; Close, J J; Wilding, R J

1999-12-01

To assess increased exposure to airborne pollutants near power lines by investigating theoretically and experimentally the behaviour of 222Rn decay product marker aerosols in the 50 Hz electric field under power lines. The behaviour of aerosols in outdoor air including those carrying 222Rn decay products was modelled theoretically in the presence of an AC field. TASTRAK alpha-particle spectroscopy was used to characterize 218Po and 214Po aerosols outdoors. Sampling points were chosen along a line at right angles up to 200 m from a number of high voltage power (transmission) lines. Each sampling point comprised an arrangement of mutually orthogonal TASTRAK detectors. Exposures were carried out at different power line locations in various weather conditions. The model predicts a two- to three-fold increase in deposition of aerosols on spherical surfaces mimicking the human head under high voltage power lines. Experimental measurements using detectors mounted on grounded metal spheres showed an enhanced deposition of both 218Po and 214Po aerosols. Enhanced 218Po deposition on 400 kV lines ranged from 1.96+/-0.15 to 2.86+/-0.32. Enhanced 214Po deposition on 275 kV and 132 kV lines were 1.43+/-0.07 and 1.11+/-0.21, respectively, where the latter value was not significant. The observations demonstrate a mode of increased exposure to pollutant aerosols under high voltage power lines by increased deposition on the body. The total (indoor + outdoor) 218Po and 214Po dose to the basal layer of facial skin is estimated to be increased by between 1.2 and 2.0 for 10% of time spent outdoors under high voltage power lines.

Insights into highly improved solar-driven photocatalytic oxygen evolution over integrated Ag3PO4/MoS2 heterostructures

NASA Astrophysics Data System (ADS)

Cui, Xingkai; Yang, Xiaofei; Xian, Xiaozhai; Tian, Lin; Tang, Hua; Liu, Qinqin

2018-04-01

Oxygen evolution has been considered as the rate-determining step in photocatalytic water splitting due to its sluggish four-electron half-reaction rate, the development of oxygen-evolving photocatalysts with well-defined morphologies and superior interfacial contact is highly important for achieving high-performance solar water splitting. Herein, we report the fabrication of Ag3PO4/MoS2 nanocomposites and, for the first time, their use in photocatalytic water splitting into oxygen under LED light illumination. Ag3PO4 nanoparticles were found to be anchored evenly on the surface of MoS2 nanosheets, confirming an efficient hybridization of two semiconductor materials. A maximum oxygen-generating rate of 201.6 mol L-1 g-1 h-1 was determined when 200 mg MoS2 nanosheets were incorporated into Ag3PO4 nanoparticles, which is around 5 times higher than that of bulk Ag3PO4. Obvious enhancements in light-harvesting property, as well as electron-hole separation and charge transportation are revealed by the combination of different characterizations. ESR analysis verified that more active oxygen-containing radicals generate over illuminated Ag3PO4/MoS2 composite photocatalysts rather than irradiated Ag3PO4. The improvement in oxygen evolution performance of Ag3PO4/MoS2 composite photocatalysts is ascribed to wide spectra response in the visible-light region, more efficient charge separation and enhanced oxidation capacity in the valence band (VB). This study provides new insights into the design and development of novel composite photocatalytic materials for solar-to-fuel conversion.

75 FR 60094 - Proposed Agency Information Collection

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-29

... utility; (b) the accuracy of the agency's estimate of the burden of the proposed collection of information... Sciences Division, Oak Ridge National Laboratory, One Bethel Valley Road, P.O. Box 2008, MS-6038, Oak Ridge... to: Bruce Tonn, Environmental Sciences Division, Oak Ridge National Laboratory, One Bethel Valley...

Understanding the fate of sanitation-related nutrients in a shallow sandy aquifer below an urban slum area

NASA Astrophysics Data System (ADS)

Nyenje, P. M.; Havik, J. C. N.; Foppen, J. W.; Muwanga, A.; Kulabako, R.

2014-08-01

We hypothesized that wastewater leaching from on-site sanitation systems to alluvial aquifers underlying informal settlements (or slums) may end up contributing to high nutrient loads to surface water upon groundwater exfiltration. Hence, we conducted a hydro-geochemical study in a shallow sandy aquifer in Bwaise III parish, an urban slum area in Kampala, Uganda, to assess the geochemical processes controlling the transport and fate of dissolved nutrients (NO3, NH4 and PO4) released from on-site sanitation systems to groundwater. Groundwater was collected from 26 observation wells. The samples were analyzed for major ions (Ca, Mg, Na, Mg, Fe, Mn, Cl and SO4) and nutrients (o-PO4, NO3 and NH4). Data was also collected on soil characteristics, aquifer conductivity and hydraulic heads. Geochemical modeling using PHREEQC was used to determine the level of o-PO4 control by mineral solubility and sorption. Groundwater below the slum area was anoxic and had near neutral pH values, high values of EC (average of 1619 μS/cm) and high concentrations of Cl (3.2 mmol/L), HCO3 (11 mmol/L) and nutrients indicating the influence from wastewater leachates especially from pit latrines. Nutrients were predominantly present as NH4 (1-3 mmol/L; average of 2.23 mmol/L). The concentrations of NO3 and o-PO4 were, however, low: average of 0.2 mmol/L and 6 μmol/L respectively. We observed a contaminant plume along the direction of groundwater flow (NE-SW) characterized by decreasing values of EC and Cl, and distinct redox zones. The redox zones transited from NO3-reducing in upper flow areas to Fe-reducing in the lower flow areas. Consequently, the concentrations of NO3 decreased downgradient of the flow path due to denitrification. Ammonium leached directly into the alluvial aquifer was also partially removed because the measured concentrations were less than the potential input from pit latrines (3.2 mmol/L). We attributed this removal (about 30%) to anaerobic ammonium oxidation (anammox) given that the cation exchange capacity of the aquifer was low (< 6 meq/100 g) to effectively adsorb NH4. Phosphate transport was, on the other hand, greatly retarded and our results showed that this was due to the adsorption of P to calcite and the co-precipitation of P with calcite and rhodochrosite. Our findings suggest that shallow alluvial sandy aquifers underlying urban slum areas are an important sink of excessive nutrients leaching from on-site sanitation systems.

Fabrication and Characterization of Luminescent Magnetic Bifunctional Nanocomposite Based on TbPO4·H2O Nanowires and Fe3O4 Nanoparticles

NASA Astrophysics Data System (ADS)

Huong, Nguyen Thanh; Hung, Nguyen Manh; Lien, Pham Thi; Van, Nguyen Duc; Nam, Pham Hong; Binh, Nguyen Thanh; Minh, Le Quoc

2016-07-01

The fabrication and properties of luminescent magnetic bifunctional nanocomposites comprised of TbPO4·H2O nanowires as a core and magnetite nanoparticles as a shell are presented. TbPO4·H2O nanowires were synthesized by a microwave-assisted method while the grafting process of freshly-formed superparamagnetic magnetite nanoparticles on the surface of luminescent nanowires was carried out by a co-precipitate method. The effects of the Fe3O4/TbPO4·H2O mass ratio on the luminescent and magnetic properties of the obtained nanocomposite were also investigated. The results showed that, for the optimized bifunctional nanocomposites, green luminescent emissions at 488 nm, 542 nm, 585 nm, 620 nm and superparamagnetic behavior with saturation magnetization M s of 6 emu/g were achieved. With a hyperthermia temperature of ~43.5°C under an alternating current (AC) magnetic field, the obtained TbPO4·H2O/Fe3O4 nanocomposite was expected to be used for both optical probing and hyperthermia cancer treatments in biomedical applications.

Synthesis of cage-like LiFePO4/C microspheres for high performance lithium ion batteries

NASA Astrophysics Data System (ADS)

Deng, Honggui; Jin, Shuangling; Zhan, Liang; Wang, Yanli; Qiao, Wenming; Ling, Licheng

2012-12-01

Cage-like LiFePO4 microspheres are synthesized by a solvothermal reaction-calcination process, using Fe(NO3)3·9H2O as iron source and ethylene glycol/water as co-solvent medium. The microsphere is the assembly of LiFePO4 nanoparticles with an open porous structure, thus the carbon coating can be easily introduced on the surface of the nanoparticles by the chemical vapor deposition of C2H4 during calcination process. When used as the cathode materials for the lithium-ion batteries, the resultant cage-like LiFePO4/C microsphere shows high capacity and good cycle stability (160 mAh g-1 at 0.1 C over 300 cycles), as well as good rate capability (120 mAh g-1 at 10 C). The desirable electrochemical performance can be attributed to high rate of ionic/electronic conduction and the high structural stability arising from the interconnected open pores, carbon-coated nanoparticles and microsized structure.

Bridging the gap between the Babinet principle and the physical optics approximation: Vectorial problem

NASA Astrophysics Data System (ADS)

Kubické, Gildas; Bourlier, Christophe; Delahaye, Morgane; Corbel, Charlotte; Pinel, Nicolas; Pouliguen, Philippe

2013-09-01

For a three-dimensional problem and by assuming perfectly electric conducting objects, this paper shows that the Babinet principle (BP) can be derived from the physical optics (PO) approximation. Indeed, following the same idea as Ufimtsev, from the PO approximation and in the far-field zone, the field scattered by an object can be split up into a field which mainly contributes around the specular direction (illuminated zone) and a field which mainly contributes around the forward direction (shadowed zone), which is strongly related to the scattered field obtained from the BP. The only difference resides in the integration surface. We show mathematically that the involved integral does not depend on the shape of the object but only on its contour. Simulations are provided to illustrate the link between BP and PO. The main gain of this work is that it provides a more complete physical insight into the connection between PO and BP.

Technology development for phosphoric acid fuel cell powerplant, phase 2

NASA Technical Reports Server (NTRS)

Christner, L.

1979-01-01

A technique for producing an acid inventory control member by spraying FEP onto a partially screened carbon paper backing is discussed. Theoretical analysis of the acid management indicates that the vapor composition of 103% H3PO4 is approximately 1.0 ppm P4O10. An SEM evaluation of corrosion resistance of phenolic resins and graphite/phenolic resin composites in H3PO4 at 185 C shows specific surface etching. Carbonization of graphite/phenolic bipolar plates is achieved without blistering.

Implementing DOIs for Oceanographic Satellite Data at PO.DAAC

NASA Astrophysics Data System (ADS)

Hausman, J.; Tauer, E.; Chung, N.; Chen, C.; Moroni, D. F.

2013-12-01

The Physical Oceanographic Distributed Active Archive Center (PO.DAAC) is NASA's archive for physical oceanographic satellite data. It distributes over 500 datasets from gravity, ocean wind, sea surface topography, sea ice, ocean currents, salinity, and sea surface temperature satellite missions. A dataset is a collection of granules/files that share the same mission/project, versioning, processing level, spatial, and temporal characteristics. The large number of datasets is partially due to the number of satellite missions, but mostly because a single satellite mission typically has multiple versions or even temporal and spatial resolutions of data. As a result, a user might mistake one dataset for a different dataset from the same satellite mission. Due to the PO.DAAC'S vast variety and volume of data and growing requirements to report dataset usage, it has begun implementing DOIs for the datasets it archives and distributes. However, this was not as simple as registering a name for a DOI and providing a URL. Before implementing DOIs multiple questions needed to be answered. What are the sponsor and end-user expectations regarding DOIs? At what level does a DOI get assigned (dataset, file/granule)? Do all data get a DOI, or only selected data? How do we create a DOI? How do we create landing pages and manage them? What changes need to be made to the data archive, life cycle policy and web portal to accommodate DOIs? What if the data also exists at another archive and a DOI already exists? How is a DOI included if the data were obtained via a subsetting tool? How does a researcher or author provide a unique, definitive reference (standard citation) for a given dataset? This presentation will discuss how these questions were answered through changes in policy, process, and system design. Implementing DOIs is not a trivial undertaking, but as DOIs are rapidly becoming the de facto approach, it is worth the effort. Researchers have historically referenced the source satellite and data center (or archive), but scientific writings do not typically provide enough detail to point to a singular, uniquely identifiable dataset. DOIs provide the means to help researchers be precise in their data citations and provide needed clarity, standardization and permanence.

Dynamic study of sub-micro sized LiFePO4 cathodes by in-situ tender X-ray absorption near edge structure

NASA Astrophysics Data System (ADS)

Wang, Dongniu; Wang, Huixin; Yang, Jinli; Zhou, Jigang; Hu, Yongfeng; Xiao, Qunfeng; Fang, Haitao; Sham, Tsun-Kong

2016-01-01

Olivine-type phosphates (LiMPO4, M = Fe, Mn, Co) are promising cathode materials for lithium-ion batteries that are generally accepted to follow first order equilibrium phase transformations. Herein, the phase transformation dynamics of sub-micro sized LiFePO4 particles with limited rate capability at a low current density of 0.14 C was investigated. An in-situ X-ray Absorption Near Edge Structure (XANES) measurement was conducted at the Fe and P K-edge for the dynamic studies upon lithiation and delithiation. Fe K-edge XANES spectra demonstrate that not only lithium-rich intermediate phase LixFePO4 (x = 0.6-0.75), but also lithium-poor intermediate phase LiyFePO4 (y = 0.1-0.25) exist during the charge and discharge, respectively. Furthermore, during charge and discharge, a fluctuation of the FePO4 and LiFePO4 fractions obtained by liner combination fitting around the imaginary phase fractions followed Faraday's law and the equilibrium first-order two-phase transformation versus reaction time is present, respectively. The charging and discharging process has a reversible phase transformation dynamics with symmetric structural evolution routes. P K-edge XANES spectra reveal an enrichment of PF6-1 anions at the surface of the electrode during charging.

Desired crystal oriented LiFePO4 nanoplatelets in situ anchored on a graphene cross-linked conductive network for fast lithium storage.

PubMed

Wang, Bo; Liu, Anmin; Abdulla, Wael Al; Wang, Dianlong; Zhao, X S

2015-05-21

Electron transfer and lithium ion diffusion rates are the key factors limiting the lithium ion storage in anisotropic LiFePO4 electrodes. In this work, we employed a facile solvothermal method to synthesize a "platelet-on-sheet" LiFePO4/graphene composite (LFP@GNs), which is LiFePO4 nanoplatelets in situ grown on graphene sheets with highly oriented (010) facets of LiFePO4 crystals. Such a two-phase contact mode with graphene sheets cross-linked to form a three-dimensional porous network is favourable for both fast lithium ion and electron transports. As a result, the designed LFP@GNs displayed a high rate capability (∼56 mA h g(-1) at 60 C) and long life cycling stability (∼87% capacity retention over 1000 cycles at 10 C). For comparison purposes, samples ex situ modified with graphene (LFP/GNs) as well as pure LiFePO4 platelets (LFP) were also prepared and investigated. More importantly, the obtained LFP@GNs can be used as a basic unit for constructing more complex structures to further improve electrochemical performance, such as coating the exposed LFP surface with a thin layer of carbon to build a C@LFP@GN composite to further enhance its cycling stability (∼98% capacity retention over 1000 cycles at 10 C).

Radon decay products in realistic living rooms and their activity distributions in human respiratory system.

PubMed

Mohery, M; Abdallah, A M; Baz, S S; Al-Amoudi, Z M

2014-12-01

In this study, the individual activity concentrations of attached short-lived radon decay products ((218)Po, (214)Pb and (214)Po) in aerosol particles were measured in ten poorly ventilated realistic living rooms. Using standard methodologies, the samples were collected using a filter holder technique connected with alpha-spectrometric. The mean value of air activity concentration of these radionuclides was found to be 5.3±0.8, 4.5±0.5 and 3.9±0.4 Bq m(-3), respectively. Based on the physical properties of the attached decay products and physiological parameters of light work activity for an adult human male recommended by ICRP 66 and considering the parameters of activity size distribution (AMD = 0.25 μm and σ(g) = 2.5) given by NRC, the total and regional deposition fractions in each airway generation could be evaluated. Moreover, the total and regional equivalent doses in the human respiratory tract could be estimated. In addition, the surface activity distribution per generation is calculated for the bronchial region (BB) and the bronchiolar region (bb) of the respiratory system. The maximum values of these activities were found in the upper bronchial airway generations. © The Author 2013. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

[Nutrients in atmospheric wet deposition in the East China Sea].

PubMed

Zhu, Yu-Mei; Liu, Su-Mei

2011-09-01

92 rainwater samples were collected at Shengsi Archipelago from January 2008 to December 2009. The pH and the concentrations of nutrients (NH4(+), NO3(-) + NO2(-), PO4(3-), SiO3(2-)) were analyzed using spectrophotometry to understand the impacts of the atmospheric wet deposition on the ecosystem of the East China Sea. The results showed that the pH of 85% samples were less than 5.0, and had significant effect on the environment. There were significant differences among monthly average concentrations of nutrients and rainfall and seasonal average wet deposition of nutrients in investigation periods. The annual average wet deposition flux was 52.05 mmol x (m2 x a) (-1) for DIN, 0.08 mmol x (m2 x a) (-1) for PO4(3-), 2.05 mmol x (m2 x a) (-1) for SiO3(2-). The average molar ratios of NO3(-)/NH4(+) is 0.73, N: P ratio is 684: 1, indicating that nutrients composition in rainwater was different from seawater of the East China Sea Shelf (10-150). The wet deposition may change the nutrients structure, pH and lead to change the phytoplankton production in the surface seawater of the East China Sea, even lead to the red tide.

A pragmatic cluster randomised controlled trial to evaluate the safety, clinical effectiveness, cost effectiveness and satisfaction with point of care testing in a general practice setting - rationale, design and baseline characteristics.

PubMed

Laurence, Caroline; Gialamas, Angela; Yelland, Lisa; Bubner, Tanya; Ryan, Philip; Willson, Kristyn; Glastonbury, Briony; Gill, Janice; Shephard, Mark; Beilby, Justin

2008-08-06

Point of care testing (PoCT) may be a useful adjunct in the management of chronic conditions in general practice (GP). The provision of pathology test results at the time of the consultation could lead to enhanced clinical management, better health outcomes, greater convenience and satisfaction for patients and general practitioners (GPs), and savings in costs and time. It could also result in inappropriate testing, increased consultations and poor health outcomes resulting from inaccurate results. Currently there are very few randomised controlled trials (RCTs) in GP that have investigated these aspects of PoCT. The Point of Care Testing in General Practice Trial (PoCT Trial) was an Australian Government funded multi-centre, cluster randomised controlled trial to determine the safety, clinical effectiveness, cost effectiveness and satisfaction of PoCT in a GP setting.The PoCT Trial covered an 18 month period with the intervention consisting of the use of PoCT for seven tests used in the management of patients with diabetes, hyperlipidaemia and patients on anticoagulant therapy. The primary outcome measure was the proportion of patients within target range, a measure of therapeutic control. In addition, the PoCT Trial investigated the safety of PoCT, impact of PoCT on patient compliance to medication, stakeholder satisfaction, cost effectiveness of PoCT versus laboratory testing, and influence of geographic location. The paper provides an overview of the Trial Design, the rationale for the research methodology chosen and how the Trial was implemented in a GP environment. The evaluation protocol and data collection processes took into account the large number of patients, the broad range of practice types distributed over a large geographic area, and the inclusion of pathology test results from multiple pathology laboratories.The evaluation protocol developed reflects the complexity of the Trial setting, the Trial Design and the approach taken within the funding provided. The PoCT Trial is regarded as a pragmatic RCT, evaluating the effectiveness of implementing PoCT in GP and every effort was made to ensure that, in these circumstances, internal and external validity was maintained. 12612605000272695.

Online Workspace to Connect Scientists with NASA's Science E/PO Efforts and Practitioners

NASA Astrophysics Data System (ADS)

Shipp, Stephanie; Bartolone , Lindsay; Peticolas, Laura; Woroner, Morgan; Dalton, Heather; Schwerin, Theresa; Smith, Denise

2014-11-01

There is a growing awareness of the need for a scientifically literate public in light of challenges facing society today, and also a growing concern about the preparedness of our future workforce to meet those challenges. Federal priorities for science, technology, engineering, and math (STEM) education call for improvement of teacher training, increased youth and public engagement, greater involvement of underrepresented populations, and investment in undergraduate and graduate education. How can planetary scientists contribute to these priorities? How can they “make their work and findings comprehensible, appealing, and available to the public” as called for in the Planetary Decadal Survey?NASA’s Science Mission Directorate (SMD) Education and Public Outreach (E/PO) workspace provides the SMD E/PO community of practice - scientists and educators funded to conduct SMD E/PO or those using NASA’s science discoveries in E/PO endeavors - with an online environment in which to communicate, collaborate, and coordinate activities, thus helping to increase effectiveness of E/PO efforts. The workspace offers interested scientists avenues to partner with SMD E/PO practitioners and learn about E/PO projects and impacts, as well as to advertise their own efforts to reach a broader audience. Through the workspace, scientists can become aware of opportunities for involvement and explore resources to improve professional practice, including literature reviews of best practices for program impact, mechanisms for engaging diverse audiences, and large- and small-scale program evaluation. Scientists will find “how to” manuals for getting started and increasing impact with public presentations, classroom visits, and other audiences, as well as primers with activity ideas and resources that can augment E/PO interactions with different audiences. The poster will introduce the workspace to interested scientists and highlight pathways to resources of interest that can help scientists more effectively contribute to national STEM education priorities. Visitors are encouraged to explore the growing collection of resources at http://smdepo.org.

A statistical approach to investigating enhancement of polonium-210 in the Eastern Irish Sea arising from discharges from a former phosphate processing plant.

PubMed

Dewar, Alastair; Camplin, William; Barry, Jon; Kennedy, Paul

2014-12-01

Since the cessation of phosphoric acid production (in 1992) and subsequent closure and decommissioning (2004) of the Rhodia Consumer Specialties Limited plant in Whitehaven, the concentration levels of polonium-210 ((210)Po) in local marine materials have declined towards a level more typical of natural background. However, enhanced concentrations of (210)Po and lead-210 ((210)Pb), due to this historic industrial activity (plant discharges and ingrowth of (210)Po from (210)Pb), have been observed in fish and shellfish samples collected from this area over the last 20 years. The results of this monitoring, and assessments of the dose from these radionuclides, to high-rate aquatic food consumers are published annually in the Radioactivity in Food and the Environment (RIFE) report series. The RIFE assessment uses a simple approach to determine whether and by how much activity is enhanced above the normal background. As a potential tool to improve the assessment of enhanced concentrations of (210)Po in routine dose assessments, a formal statistical test, where the null hypothesis is that the Whitehaven area is contaminated with (210)Po, was applied to sample data. This statistical, modified "green", test has been used in assessments of chemicals by the OSPAR commission. It involves comparison of the reported environmental concentrations of (210)Po in a given aquatic species against its corresponding Background Assessment Concentration (BAC), which is based upon environmental samples collected from regions assumed to be not enhanced by industrial sources of (210)Po, over the period for which regular monitoring data are available (1990-2010). Unlike RIFE, these BAC values take account of the variability of the natural background level. As an example, for 2010 data, crab, lobster, mussels and winkles passed the modified "green" test (i.e. the null hypothesis is rejected) and as such are deemed not to be enhanced. Since the cessation of phosphoric acid production in 1992, the modified "green" test pass rate for crustaceans is ∼53% and ∼64% for molluscs. Results of dose calculations are made (i) using the RIFE approach and (ii) with the application of the modified "green" test, where samples passing the modified "green" test are assumed to have background levels and hence zero enhancement of (210)Po. Applying the modified "green" test reduces the dose on average by 44% over the period of this study (1990-2010). Crown Copyright © 2014. Published by Elsevier Ltd. All rights reserved.

Effects of calcium and phosphate on uranium(IV) oxidation: Comparison between nanoparticulate uraninite and amorphous U IV–phosphate

DOE PAGES

Latta, Drew E.; Kemner, Kenneth M.; Mishra, Bhoopesh; ...

2015-11-17

The mobility of uranium in subsurface environments depends strongly on its redox state, with U IV phases being significantly less soluble than U VI minerals. This study compares the oxidation kinetics and mechanisms of two potential products of U VI reduction in natural systems, a nanoparticulate UO 2 phase and an amorphous U IV–Ca–PO 4 analog to ningyoite (CaU IV(PO 4) 2·1–2H 2O). The valence of U was tracked by X-ray absorption near-edge spectroscopy (XANES), showing similar oxidation rate constants for U IVO 2 and U IV–phosphate in solutions equilibrated with atmospheric O 2 and CO 2 at pH 7.0more » (k obs,UO2 = 0.17 ± 0.075 h -1 vs. k obs,U IV PO4 = 0.30 ± 0.25 h -1). Addition of up to 400 μM Ca and PO 4 decreased the oxidation rate constant by an order of magnitude for both UO 2 and U IV–phosphate. The intermediates and products of oxidation were tracked by electron microscopy, powder X-ray diffraction (pXRD), and extended X-ray absorption fine-structure spectroscopy (EXAFS). In the absence of Ca or PO 4, the product of UO 2 oxidation is Na–uranyl oxyhydroxide (under environmentally relevant concentrations of sodium, 15 mM NaClO 4 and low carbonate concentration), resulting in low concentrations of dissolved U VI (<2.5 × 10 -7 M). Oxidation of U IV–phosphate produced a Na-autunite phase (Na 2(UO 2)PO 4·xH 2O), resulting in similarly low dissolved U concentrations (<7.3 × 10 -8 M). When Ca and PO 4 are present in the solution, the EXAFS data and the solubility of the UVI phase resulting from oxidation of UO 2 and UIV–phosphate are consistent with the precipitation of Na-autunite. Bicarbonate extractions and Ca K-edge X-ray absorption spectroscopy of oxidized solids indicate the formation of a Ca–UVI–PO 4 layer on the UO 2 surface and suggest a passivation layer mechanism for the decreased rate of UO 2 oxidation in the presence of Ca and PO 4. Interestingly, the extractions were unable to remove all of the oxidized U from partially oxidized UO 2 solids, suggesting that oxidized U is distributed between the interior of the UO 2 nanoparticles and the labile surface layer. Accounting for the entire pool of oxidized U by XANES is the likely reason for the higher UO 2 oxidation rate constants determined here relative to prior studies. In conclusion, our results suggest that the natural presence or addition of Ca and PO 4 in groundwater could slow the rates of U IV oxidation, but that the rates are still fast enough to cause complete oxidation of U IV within days under fully oxygenated conditions.« less

Hydrochemical and Isotopic Composition of The Water Resources In The Po Delta Plain (northern Italy) and Its Environmental Impact

NASA Astrophysics Data System (ADS)

Rapti Caputo, D.; Martinelli, G.

Groundwater samples from wells were collected to examine the hydrochemical char- acteristics and isotopic composition of the water resources in the Ferrara area (delta Po plain). Electrical conductivity (EC), pH, total dissolved solid (TDS), temperature of the water were directly measured in the field. Subsequently, in the laboratory, the samples were analysed for the determination of major ions such as Ca, Mg, K, Na, SO4, Cl, NO3 and HCO3. Also, oxygen, deuterium and tritium isotopic composition, of the same samples were analysed for the isotopic characterisation of the waters. Three principal water groups can be distinguished on the basis of the distribution of the values of 18O and 2H. The first group (A), include the waters from the wells that exploit the unsatured shallow aquifer, developing in mainly sandy or sandy-silty lenses. These are large diameter wells, whose depth does not exceed the 7 m, while their piezometric level is at depth varying between 2 and 3 m from the soil surface. The isotopic composition of such wells is strongly affected by meteorological events (local recharge). Indeed, the main supply to the aquifer occurs through infiltration, mainly from rainwaters and, secondly, from the waters contained in the drainage channels. The hydrochemical characteristics of the waters coming from those wells present a very high sulphate concentration (up to 508 mg/l). To the second group (B) belong the waters with an 18O and 2H content lower than the previously described group and varying, respectively, between -9.6 < 18O < -9.0 and 68.9 < 2H < -64.7. In partic- ular, this group include the waters from the wells exploiting the first confined aquifer sistem, developed in mainly sandy layers. The top of this hydrogeological units, is at a depth varying between 15 and 20 m from the soil surface, while the thickness varies from 20 and 35 m. The waters of this goup present low oxygen values and deuterium and a substantial variation in the traces of tritium with variations from 2.5 to 22.5 +/- 3.9 UT. The low concentration of 2.5 UT, in particular, allows us to evaluate a resi- dence time in underground aquifer for these waters of about 30 years. The high tritium content value of the waters (22.5 +/- 5.6 UT) can be interpreted as mixing phenom- ena between the 'old' waters of the confined aquifer and the 'recent additions' of the network hydrological system situated in the area of the Ferrara plain (Po and Po di Volano rivers). In group C, are the waters of the Po River, where low values can be 1 observed both in oxygen and deuterium contents, with values equal to -9.90 s´ 0.03 and -71.3 s´ 0.9, respectively.

Pattern of Onset and Risk Factors for Peripheral Oedema During Vildagliptin Use: Analysis from the Vildagliptin Prescription-Event Monitoring Study in England.

PubMed

Layton, Deborah; Coughtrie, Abigail L; Qayum, Naseer; Shakir, Saad A W

2016-11-01

Clinical trials have identified peripheral oedema (PO) as an adverse event of vildagliptin (an oral anti-diabetic drug [OAD]). A post-marketing study (PMS) was conducted to advance the understanding of vildagliptin use and particular safety concerns identified within the risk-management plan. PMS objectives included comparing the hazards between vildagliptin monotherapy and combination therapy for selected a priori identified risks, including PO. This study was a per-protocol supplementary analysis to investigate the pattern of onset and effect of vildagliptin combination therapy on PO risk. The PMS used an observational cohort design. OAD exposure, selected risk factors and outcome data were collected from general practitioners in England regarding vildagliptin users for the 6-month period after starting treatment. Data analysis comprised univariate case/non-case analysis, time-to-onset analysis and Cox proportional hazard models to estimate hazard ratios (HR) of PO adjusting for selected patients' baseline characteristics. The study cohort included 4828 patients (median age 63 years; interquartile range [IQR] 54-71), 2692 of whom were male (55.8 %). The crude cumulative hazard of PO was 19.09 cases (95 % confidence interval [CI] 13.54-26.10) per 1000 person-years; 50 % of cases occurred during the first 34 days of treatment. A significantly faster time to PO onset was observed in patients prescribed concomitant sulfonylureas versus other treatment combinations (log rank test [LRT] p = 0.0365); in patients with a prior history of PO (LRT p < 0.001), arrhythmia (LRT p = 0.0003) or hypertension (LRT p = 0.0125); and in patients aged ≥60 years (LRT p = 0.0047). Similarly, the case/non-case univariate analysis indicated that patients with PO were older; had a higher prevalence of a history of either arrhythmia, hypertension or PO; and frequently used a sulfonylurea in combination. In the hazard function analysis, only sex and prior PO history had a profound effect on risk of PO after starting vildagliptin. Furthermore, effect modification was observed between sex and prior PO history; in male patients of average age (62 years), the HR was 12.84 (95 % CI 4.96-33.23); in females, it was 1.44 (95 % CI 0.32-6.40). In this planned supplementary analysis, the findings suggest that PO occurred most frequently within 1 month after starting treatment with vildagliptin, and previous PO history and male sex in elderly patients were important predictors of this risk. The observation that concomitant use of a sulfonylurea may also increase PO risk early after starting treatment should be taken into consideration if prescribing OADs in combination with vildagliptin.

Satellite Remote Sensing of Ocean Winds, Surface Waves and Surface Currents during the Hurricanes

NASA Astrophysics Data System (ADS)

Zhang, G.; Perrie, W. A.; Liu, G.; Zhang, L.

2017-12-01

Hurricanes over the ocean have been observed by spaceborne aperture radar (SAR) since the first SAR images were available in 1978. SAR has high spatial resolution (about 1 km), relatively large coverage and capability for observations during almost all-weather, day-and-night conditions. In this study, seven C-band RADARSAT-2 dual-polarized (VV and VH) ScanSAR wide images from the Canadian Space Agency (CSA) Hurricane Watch Program in 2017 are collected over five hurricanes: Harvey, Irma, Maria, Nate, and Ophelia. We retrieve the ocean winds by applying our C-band Cross-Polarization Coupled-Parameters Ocean (C-3PO) wind retrieval model [Zhang et al., 2017, IEEE TGRS] to the SAR images. Ocean waves are estimated by applying a relationship based on the fetch- and duration-limited nature of wave growth inside hurricanes [Hwang et al., 2016; 2017, J. Phys. Ocean.]. We estimate the ocean surface currents using the Doppler Shift extracted from VV-polarized SAR images [Kang et al., 2016, IEEE TGRS]. C-3PO model is based on theoretical analysis of ocean surface waves and SAR microwave backscatter. Based on the retrieved ocean winds, we estimate the hurricane center locations, maxima wind speeds, and radii of the five hurricanes by adopting the SHEW model (Symmetric Hurricane Estimates for Wind) by Zhang et al. [2017, IEEE TGRS]. Thus, we investigate possible relations between hurricane structures and intensities, and especially some possible effects of the asymmetrical characteristics on changes in the hurricane intensities, such as the eyewall replacement cycle. The three SAR images of Ophelia include the north coast of Ireland and east coast of Scotland allowing study of ocean surface currents respond to the hurricane. A system of methods capable of observing marine winds, surface waves, and surface currents from satellites is of value, even if these data are only available in near real-time or from SAR-related satellite images. Insight into high resolution ocean winds, waves and currents in hurricanes can be useful for intensity prediction, which has had relatively few improvements in the past 25 years. In 2018 RADARSAT Constellation Mission will be launched, increasing SAR coverage by 10×, allowing increased observations during the next hurricane season.

Tidal Pumping-Induced Nutrients Dynamics and Biogeochemical Implications in an Intertidal Aquifer

NASA Astrophysics Data System (ADS)

Liu, Yi; Jiao, Jiu Jimmy; Liang, Wenzhao; Luo, Xin

2017-12-01

Tidal pumping is a major driving force affecting water exchange between land and sea, biogeochemical reactions in the intertidal aquifer, and nutrient loading to the sea. At a sandy beach of Tolo Harbour, Hong Kong, the nutrient (NH4+, NO2-, NO3-, and PO43-) dynamic in coastal groundwater mixing zone (CGMZ) is found to be fluctuated with tidal oscillation. Nutrient dynamic is mainly controlled by tidal pumping-induced organic matter that serves as a reagent of remineralization in the aquifer. NH4+, NO2-, and PO43- are positively correlated with salinity. Both NH4+ and PO43- have negative correlations with oxidation/reduction potential. NH4+ is the major dissolved inorganic nitrogen species in CGMZ. The adsorption of PO43- onto iron oxides occurs at the deep transition zone with a salinity of 5-10 practical salinity unit (psu), and intensive N-loss occurs in near-surface area with a salinity of 10-25 psu. The biogeochemical reactions, producing PO43- and consuming NH4+, are synergistic effect of remineralization-nitrification-denitrification. In CGMZ, the annual NH4+ loss is estimated to be 4.32 × 105 mol, while the minimum annual PO43- production is estimated to be 2.55 × 104 mol. Applying these rates to the entire Tolo Harbour, the annual NH4+ input to the harbor through the remineralization of organic matters is estimated to be 1.02 × 107 mol. The annual NH4+ loss via nitrification is 1.32 × 107 mol, and the annual PO43- production is 7.76 × 105 mol.

7 CFR 91.42 - Billing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... voluntary laboratory services and other services were rendered at a particular Science and Technology..., National Finance Center Billings and Collection Branch, (Mail: P.O. Box 60075), 13800 Old Gentilly Road...

7 CFR 91.42 - Billing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... voluntary laboratory services and other services were rendered at a particular Science and Technology..., National Finance Center Billings and Collection Branch, (Mail: P.O. Box 60075), 13800 Old Gentilly Road...

7 CFR 91.42 - Billing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... voluntary laboratory services and other services were rendered at a particular Science and Technology..., National Finance Center Billings and Collection Branch, (Mail: P.O. Box 60075), 13800 Old Gentilly Road...

7 CFR 91.42 - Billing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... voluntary laboratory services and other services were rendered at a particular Science and Technology..., National Finance Center Billings and Collection Branch, (Mail: P.O. Box 60075), 13800 Old Gentilly Road...

7 CFR 91.42 - Billing.

Code of Federal Regulations, 2011 CFR

2011-01-01

... voluntary laboratory services and other services were rendered at a particular Science and Technology..., National Finance Center Billings and Collection Branch, (Mail: P.O. Box 60075), 13800 Old Gentilly Road...

Probing the Influence of Disorder on Lanthanide Luminescence Using Eu-Doped LaPO4 Nanoparticles

PubMed Central

2017-01-01

Lanthanide-doped nanocrystals (NCs) differ from their bulk counterparts due to their large surface to volume ratio. It is generally assumed that the optical properties are not affected by size effects as electronic transitions occur within the well-shielded 4f shell of the lanthanide dopant ions. However, defects and disorder in the surface layer can affect the luminescence properties. Trivalent europium is a suitable ion to investigate the subtle influence of the surface, because of its characteristic luminescence and high sensitivity to the local environment. Here, we investigate the influence of disorder in NCs on the optical properties of lanthanide dopants by studying the inhomogeneous linewidth, emission intensity ratios, and luminescence decay curves for LaPO4:Eu3+ samples of different sizes (4 nm to bulk) and core–shell configurations (core, core–isocrystalline shell, and core–silica shell). We show that the emission linewidths increase strongly for NCs. The ratio of the intensities of the forced electric dipole (ED) and magnetic dipole (MD) transitions, a measure for the local symmetry distortion around Eu3+ ions, is higher for samples with a large fraction of Eu3+ ions close to the surface. Finally, we present luminescence decay curves revealing an increased nonradiative decay rate for Eu3+ in NCs. The effects are strongest in core and core–silica shell NCs and can be reduced by growth of an isocrystalline LaPO4 shell. The present systematic study provides quantitative insight into the role of surface disorder on the optical properties of lanthanide-doped NCs. These insights are important in emerging applications of lanthanide-doped nanocrystals. PMID:28919934

A non-invasive experimental approach for surface temperature measurements on semi-crystalline thermoplastics

NASA Astrophysics Data System (ADS)

Boztepe, Sinan; Gilblas, Remi; de Almeida, Olivier; Le Maoult, Yannick; Schmidt, Fabrice

2017-10-01

Most of the thermoforming processes of thermoplastic polymers and their composites are performed adopting a combined heating and forming stages at which a precursor is heated prior to the forming. This step is done in order to improve formability by softening the thermoplastic polymer. Due to low thermal conductivity and semi-transparency of polymers, infrared (IR) heating is widely used for thermoforming of such materials. Predictive radiation heat transfer models for temperature distributions are therefore critical for optimizations of thermoforming process. One of the key challenges is to build a predictive model including the physical background of radiation heat transfer phenomenon in semi-crystalline thermoplastics as their microcrystalline structure introduces an optically heterogeneous medium. In addition, the accuracy of a predictive model is required to be validated experimentally where IR thermography is one of the suitable methods for such a validation as it provides a non-invasive, full-field surface temperature measurement. Although IR cameras provide a non-invasive measurement, a key issue for obtaining a reliable measurement depends on the optical characteristics of a heated material and the operating spectral band of IR camera. It is desired that the surface of a material to be measured has a spectral band where the material behaves opaque and an employed IR camera operates in the corresponding band. In this study, the optical characteristics of the PO-based polymer are discussed and, an experimental approach is proposed in order to measure the surface temperature of the PO-based polymer via IR thermography. The preliminary analyses showed that IR thermographic measurements may not be simply performed on PO-based polymers and require a correction method as their semi-transparent medium introduce a challenge to obtain reliable surface temperature measurements.

Crystal structure and phase transformations of calcium yttrium orthophosphate, Ca 3Y(PO 4) 3

NASA Astrophysics Data System (ADS)

Fukuda, Koichiro; Iwata, Tomoyuki; Niwa, Takahiro

2006-11-01

Crystal structure and phase transformations of calcium yttrium orthophosphate Ca 3Y(PO 4) 3 were investigated by X-ray powder diffraction, selected-area electron diffraction, transmission electron microscopy and optical microscopy. The high-temperature phase is isostructural with eulytite, cubic (space group I4¯3d) with a=0.983320(5) nm, V=0.950790(8) nm 3, Z=4 and D x=3.45 Mg m -3. The crystal structure was refined with a split-atom model, in which the oxygen atoms are distributed over two partially occupied sites. Below the stable temperature range of eulytite, the crystal underwent a martensitic transformation, which is accompanied by the formation of platelike surface reliefs. The inverted crystal is triclinic (space group P1) with a=1.5726(1) nm, b=0.84267(9) nm, c=0.81244(8) nm, α=109.739(4)°, β=90.119(5)°, γ=89.908(7)°, V=1.0134(1) nm 3, Z=4 and D x=3.24 Mg m -3. The crystal grains were composed of pseudo-merohedral twins. The adjacent twin domains were related by the pseudo-symmetry mirror planes parallel to {101¯} with the composition surface {101¯}. When the eulytite was cooled relatively slowly from the stable temperature range, the decomposition reaction of Ca 3Y(PO 4) 3→ β-Ca 3(PO 4) 2+YPO 4 occurred.

Evaluation of multi-mode CryoSat-2 altimetry data over the Po River against in situ data and a hydrodynamic model

NASA Astrophysics Data System (ADS)

Schneider, Raphael; Tarpanelli, Angelica; Nielsen, Karina; Madsen, Henrik; Bauer-Gottwein, Peter

2018-02-01

Coverage of in situ observations to monitor surface waters is insufficient on the global scale, and decreasing across the globe. Satellite altimetry has become an increasingly important monitoring technology for continental surface waters. The ESA CryoSat-2 altimetry mission, launched in 2010, has two novel features. (i) The radar altimeter instrument on board of CryoSat-2 is operated in three modes; two of them reduce the altimeter footprint by using Delay-Doppler processing. (ii) CryoSat-2 is placed on a distinct orbit with a repeat cycle of 369 days, leading to a drifting ground track pattern. The drifting ground track pattern challenges many common methods of processing satellite altimetry data over rivers. This study evaluates the observation error of CryoSat-2 water level observations over the Po River, Italy, against in situ observations. The average RMSE between CryoSat-2 and in situ observations was found to be 0.38 meters. CryoSat-2 was also shown to be useful for channel roughness calibration in a hydrodynamic model of the Po River. The small across-track distance of CryoSat-2 means that observations are distributed almost continuously along the river. This allowed resolving channel roughness with higher spatial resolution than possible with in situ or virtual station altimetry data. Despite the Po River being extensively monitored, CryoSat-2 still provides added value thanks to its unique spatio-temporal sampling pattern.

Topological insulators double perovskites: A2TePoO6 (A = Ca, Sr, Ba)

NASA Astrophysics Data System (ADS)

Lee, Po-Han; Zhou, Jian; Pi, Shu-Ting; Wang, Yin-Kuo

2017-12-01

Based on first-principle calculations and direct density functional theory calculations of surface bands, we predict a new class of three-dimensional (3D) Z2 topological insulators (TIs) with larger bulk bandgaps up to 0.4 eV in double perovskite materials A2TePoO6 (A = Ca, Sr, and Ba). The larger nontrivial gaps are induced by the symmetry-protected band contact along with band inversion occurring in the absence of spin-orbit coupling (SOC) making the SOC more effective than conventional TIs. The proposed materials are chemically inert and more robust to surface perturbations due to its intrinsic protection layer. This study provides the double perovskite material as a rich platform to design new TI-based electronic devices.

‘Reliability of new poly (lactic-co-glycolic acid) membranes treated with oxygen plasma plus silicon dioxide layers for pre-prosthetic guided bone regeneration processes’

PubMed Central

Castillo-Dalí, Gabriel; Batista-Cruzado, Antonio; López-Santos, Carmen; Rodríguez-González-Elipe, Agustín; Saffar, Jean-Louis; Lynch, Christopher D.; Gutiérrez-Pérez, José-Luis; Torres-Lagares, Daniel

2017-01-01

Background The use of cold plasmas may improve the surface roughness of poly(lactic-co-glycolic) acid (PLGA) membranes, which may stimulate the adhesion of osteogenic mediators and cells, thus accelerating the biodegradation of the barriers. Moreover, the incorporation of metallic-oxide particles to the surface of these membranes may enhance their osteoinductive capacity. Therefore, the aim of this paper was to evaluate the reliability of a new PLGA membrane after being treated with oxygen plasma (PO2) plus silicon dioxide (SiO2) layers for guided bone regeneration (GBR) processes. Material and Methods Circumferential bone defects (diameter: 11 mm; depth: 3 mm) were created on the top of eight experimentation rabbits’ skulls and were randomly covered with: (1) PLGA membranes (control), or (2) PLGA/PO2/SiO2 barriers. The animals were euthanized two months afterwards. A micromorphologic study was then performed using ROI (region of interest) colour analysis. Percentage of new bone formation, length of mineralised bone, concentration of osteoclasts, and intensity of ostheosynthetic activity were assessed and compared with those of the original bone tissue. The Kruskal-Wallis test was applied for between-group com Asignificance level of a=0.05 was considered. Results The PLGA/PO2/SiO2 membranes achieved the significantly highest new bone formation, length of mineralised bone, concentration of osteoclasts, and ostheosynthetic activity. The percentage of regenerated bone supplied by the new membranes was similar to that of the original bone tissue. Unlike what happened in the control group, PLGA/PO2/SiO2 membranes predominantly showed bone layers in advanced stages of formation. Conclusions The addition of SiO2 layers to PLGA membranes pre-treated with PO2 improves their bone-regeneration potential. Although further research is necessary to corroborate these conclusions in humans, this could be a promising strategy to rebuild the bone architecture prior to rehabilitate edentulous areas. Key words:Guided bone regeneration (GBR), poly(lactic-co-glycolic acid) (PLGA), membrane; oxygen plasma (PO2), nanocomposite, silicon dioxide layers. PMID:28160588

The conformation of Pluronic block copolymers adsorbed on carbon nanotubes and their interaction with water studied by small-angle neutron scattering

NASA Astrophysics Data System (ADS)

Cohen, Yachin; Granite, Meirav; Pyckhout-Hintzen, Wim; Radulescu, Aurel

2010-03-01

Amphiphilic block copolymers are particularly useful in dispersing single-walled carbon nanotubes (SWCNT) in water. Small-angle neutron scattering measurements conducted at different D2O/H2O content of the dispersing medium provide quantitative information on the adsorption density and conformation of the polymer interacting with the nanotube surface. Data is presented on Pluronic F108 - (EO)132(PO)50(EO)132 and F127 (EO)100(PO)65(EO)100, where EO-ethylene oxide and PO-propylene oxide, well below the critical micellization temperature of the polymer. A dense coating of the PPO blocks on the nanotube surface is determined with the PEO chains extended from the cylindrical core-shell structure. The data from the two Pluronic systems show minimal scattering at about 70% D2O in the dispersing water, which exhibit a q -1 power law of the scattering vector (q ). This indicates near matching of the polymer chains at a surprisingly high scattering length density. The model fit required considerations of tight association of water molecules around PEO chains and slight isotopic selectivity.

Study by AES, EELS Spectroscopy of electron Irradiation on InP and InPO4/InP in comparison with Monte Carlo simulation

NASA Astrophysics Data System (ADS)

Lounis, Z.; Bouslama, M.; Hamaida, K.; Jardin, C.; Abdellaoui, A.; Ouerdane, A.; Ghaffour, M.; Berrouachedi, N.

2012-02-01

We give the great interest to characterise the InP and InPO4/InP submitted to electron beam irradiation owing to the Auger Electron Spectroscopy (AES) associated to both methods Electron Energy Loss Spectroscopy (EELS). The incident electron produces breaking of (In-P) chemical bonds. The electron beam even acts to stimulate oxidation of InP surface involving on the top layers. Other, the oxide InPO4 developed on InP does appear very sensitive to the irradiation due to electron beam shown by the monitoring of EELS spectra recorded versus the irradiated times of the surface. There appears a new oxide thought to be In2O3. We give the simulation methods Casino (Carlo simulation of electron trajectory in solids) for determination with accuracy the loss energy of backscattered electrons and compared with reports results have been obtained with EELS Spectroscopy. These techniques of spectroscopy alone do not be able to verify the affected depth during interaction process. So, using this simulation method, we determine the interaction of electrons in the matter.

Cardiorespiratory responses of the facultative air-breathing fish jeju, Hoplerythrinus unitaeniatus (Teleostei, Erythrinidae), exposed to graded ambient hypoxia.

PubMed

Oliveira, R D; Lopes, J M; Sanches, J R; Kalinin, A L; Glass, M L; Rantin, F T

2004-12-01

The jeju, Hoplerythrinus unitaeniatus, is equipped with a modified part of the swim bladder that allows aerial respiration. On this background, we have evaluated its respiratory and cardiovascular responses to aquatic hypoxia. Its aquatic O2 uptake (V(O2)) was maintained constant down to a critical P(O2) (P(cO2)) of 40 mm Hg, below which V(O2) declined linearly with further reductions of P(iO2). Just below P(cO2), the ventilatory tidal volume (V(T)) increased significantly along with gill ventilation (V(G)), while respiratory frequency changed little. Consequently, water convection requirement (V(G)/V(O2)) increased steeply. The same threshold applied to cardiovascular responses that included reflex bradycardia and elevated arterial blood pressure (P(a)). Aerial respiration was initiated at water P(O2) of 44 mm Hg and breathing episodes and time at the surface increased linearly with more severe hypoxia. At the lowest water P(O2) (20 mm Hg), the time spent at the surface accounted for 50% of total time. This response has a character of a temporary emergency behavior that may allow the animal to escape hypoxia.

Study of modulation property to incident laser by surface micro-defects on KH2PO4 crystal

NASA Astrophysics Data System (ADS)

Chen, Ming-Jun; Cheng, Jian; Li, Ming-Quan; Xiao, Yong

2012-06-01

KH2PO4 crystal is a crucial optical component of inertial confinement fusion. Modulation of an incident laser by surface micro-defects will induce the growth of surface damage, which largely restricts the enhancement of the laser induced damage threshold. The modulation of an incident laser by using different kinds of surface defects are simulated by employing the three-dimensional finite-difference time-domain method. The results indicate that after the modulation of surface defects, the light intensity distribution inside the crystal is badly distorted, with the light intensity enhanced symmetrically. The relations between modulation properties and defect geometries (e.g., width, morphology, and depth of defects) are quite different for different defects. The modulation action is most obvious when the width of surface defects reaches 1.064 μm. For defects with smooth morphology, such as spherical pits, the degree of modulation is the smallest and the light intensity distribution seems relatively uniform. The degree of modulation increases rapidly with the increase of the depth of surface defects and becomes stable when the depth reaches a critical value. The critical depth is 1.064 μm for cuboid pits and radial cracks, while for ellipsoidal pits the value depends on both the width and the length of the defects.

Relationships between northern Adriatic Sea mucilage events and climate variability.

PubMed

Deserti, Marco; Cacciamani, Carlo; Chiggiato, Jacopo; Rinaldi, Attilio; Ferrari, Carla R

2005-12-15

A long term analysis (1865-2002) of meteorological data collected in the Po Valley and Northern Adriatic Basin have been analysed to find possible links between variability in the climatic parameters and the phenomenon of mucilage. Seasonal anomalies of temperature, calculated as spatial mean over the Po Valley area, and anomalies of North Atlantic Oscillation were compared with the historical record of mucilage episodes. Both climatic indices were found to be positively correlated with mucilage events, suggesting a possible relationship between climatic variability and the increased appearance of mucilage aggregates.

Near-simultaneous hemoglobin saturation and oxygen tension maps in mouse brain using an AOTF microscope.

PubMed

Shonat, R D; Wachman, E S; Niu, W; Koretsky, A P; Farkas, D L

1997-09-01

A newly developed microscope using acousto-optic tunable filters (AOTFs) was used to generate in vivo hemoglobin saturation (SO2) and oxygen tension (PO2) maps in the cerebral cortex of mice. SO2 maps were generated from the spectral analysis of reflected absorbance images collected at different wavelengths, and PO2 maps were generated from the phosphorescence lifetimes of an injected palladium-porphyrin compound using a frequency-domain measurement. As the inspiratory O2 was stepped from hypoxia (10% O2), through normoxia (21% O2), to hyperoxia (60% O2), measured SO2 and PO2 levels rose accordingly and predictably throughout. A plot of SO2 versus PO2 in different arterial and venous regions of the pial vessels conformed to the sigmoidal shape of the oxygen-hemoglobin dissociation curve, providing further validation of the two mapping procedures. The study demonstrates the versatility of the AOTF microscope for in vivo physiologic investigation, allowing for the generation of nearly simultaneous SO2 and PO2 maps in the cerebral cortex, and the frequency-domain detection of phosphorescence lifetimes. This class of study opens up exciting new possibilities for investigating the dynamics of hemoglobin and O2 binding during functional activation of neuronal tissues.

Near-simultaneous hemoglobin saturation and oxygen tension maps in mouse brain using an AOTF microscope.

PubMed Central

Shonat, R D; Wachman, E S; Niu, W; Koretsky, A P; Farkas, D L

1997-01-01

A newly developed microscope using acousto-optic tunable filters (AOTFs) was used to generate in vivo hemoglobin saturation (SO2) and oxygen tension (PO2) maps in the cerebral cortex of mice. SO2 maps were generated from the spectral analysis of reflected absorbance images collected at different wavelengths, and PO2 maps were generated from the phosphorescence lifetimes of an injected palladium-porphyrin compound using a frequency-domain measurement. As the inspiratory O2 was stepped from hypoxia (10% O2), through normoxia (21% O2), to hyperoxia (60% O2), measured SO2 and PO2 levels rose accordingly and predictably throughout. A plot of SO2 versus PO2 in different arterial and venous regions of the pial vessels conformed to the sigmoidal shape of the oxygen-hemoglobin dissociation curve, providing further validation of the two mapping procedures. The study demonstrates the versatility of the AOTF microscope for in vivo physiologic investigation, allowing for the generation of nearly simultaneous SO2 and PO2 maps in the cerebral cortex, and the frequency-domain detection of phosphorescence lifetimes. This class of study opens up exciting new possibilities for investigating the dynamics of hemoglobin and O2 binding during functional activation of neuronal tissues. Images FIGURE 1 FIGURE 3 FIGURE 4 FIGURE 6 PMID:9284290

Impact of wastewater-irrigation on in-household water contamination. A cohort study among urban farmers in Ahmedabad, India.

PubMed

Falkenberg, Timo; Saxena, Deepak; Kistemann, Thomas

2018-10-15

This cohort study explores the contribution of wastewater irrigation, in the context of WASH (Water, Sanitation, Hygiene), on in-household water contamination among urban farming households in Ahmedabad, India. Drinking water samples of 204 households in four peri-urban farming communities were collected from the point-of-source (PoS) and point-of-use (PoU) of each household four times over the 12-month follow-up period. Next to the quantification of E. coli, three household surveys (baseline, hygiene and farm) were conducted. Additionally, an observational spot-check was undertaken in bi-monthly intervals throughout the follow-up period. Significant positive differences in water quality between PoS and PoU samples were identified in 78% of households. During the monsoon, the peak of contamination, only 6% of households had access to safe drinking water at PoU. The Average Treatment Effect (ATE) of wastewater irrigation indicates an adverse effect on in-household water contamination, larger in effect size than the mitigation effect of access to sanitation or personal hygiene. To control transmission of fecal pathogens, effective barriers are required for wastewater irrigation similar to the necessity of ensuring access to sanitation and practicing adequate hygiene behavior. Copyright © 2018 The Authors. Published by Elsevier B.V. All rights reserved.

Natural radioactive contaminants in solder

NASA Astrophysics Data System (ADS)

Bunzl, K.; Kracke, W.

1985-07-01

Comparatively high surface count rates for alpha- and beta-radiation were observed for several solders. They were identified as 210Pb and 210Po. The corresponding specific activities in solder were determined.

Pediatric appendicitis and need for antibiotics at time of discharge: Does route of administration matter?

PubMed

Acker, Shannon N; Hurst, Amanda L; Bensard, Denis D; Schubert, Anna; Dewberry, Lindel; Gonzales, Danielle; Parker, Sarah K; Tong, Suhong; Partrick, David A

2016-07-01

Following complicated appendicitis, there are limited data available to guide the surgeon regarding antibiotic selection, specifically in regards to route of administration. We hypothesized that among children with appendicitis who are discharged home with antibiotic therapy, the post-discharge readmission and complication rates do not differ between those children who receive IV antibiotics and those who receive PO antibiotics. We performed a retrospective review of all children discharged home on antibiotics following appendectomy at a single institution between 11/10-10/14. We compared outcomes including ED and hospital readmission rates, and development of postoperative complications, between those children who were discharged on IV antibiotics and those discharged on PO antibiotics. 325 children were discharged with antibiotics following appendectomy (n=291 PO antibiotics group; n=34 IV group). On both univariate and multivariate analysis, rate of each complication did not differ between the two groups including inpatient readmission (5% PO vs. 6% IV; p=0.8), ED readmission (10% vs. 11%; p=0.8), postdischarge complications related to the operation (10% vs. 15%; p=0.4), or abscess development post-discharge (4% vs. 3%; p=1). Among children with complicated appendicitis who are discharged home with ongoing antibiotic therapy, our data demonstrate no differences in outcomes between those children who receive IV and PO antibiotics. Further data, collected in a prospective fashion, are needed to clarify the role of IV and PO antibiotics among children with perforated appendicitis. Copyright © 2016 Elsevier Inc. All rights reserved.

Partial Oxygen Pressure Affects the Expression of Prognostic Biomarkers HIF-1 Alpha, Ki67, and CK20 in the Microenvironment of Colorectal Cancer Tissue.

PubMed

Zhang, Lirong; Hu, Yu; Xi, Ning; Song, Jie; Huang, Wenjing; Song, Shanshan; Liu, Yiting; Liu, Xianying; Xie, Yingjun

2016-01-01

Hypoxia is prognostically important in colorectal cancer (CRC) therapy. Partial oxygen pressure (pO 2 ) is an important parameter of hypoxia. The correlation between pO 2 levels and expression levels of prognostic biomarkers was measured in CRC tissues. Human CRC tissues were collected and pO 2 levels were measured by OxyLite. Three methods for tissue fixation were compared, including formalin, Finefix, and Finefix-plus-microwave. Immunohistochemistry (IHC) staining was conducted by using the avidin-biotin complex technique for detecting the antibodies to hypoxia inducible factor-1 (HIF-1) alpha, cytokeratin 20 (CK20), and cell proliferation factor Ki67. The levels of pO 2 were negatively associated with the size of CRC tissues. Finefix-plus-microwave fixation has the potential to replace formalin. Additionally, microwave treatment improved Finefix performance in tissue fixation and protein preservation. The percentage of positive cells and gray values of HIF-1 alpha, CK20, and Ki67 were associated with CRC development ( P < 0.05). The levels of pO 2 were positively related with the gray values of Ki67 and negatively related with the values of HIF-1 alpha and CK20 ( P < 0.05). Thus, the levels of microenvironmental pO 2 affect the expression of predictive biomarkers HIF-1 alpha, CK20, and Ki67 in the development of CRC tissues.

Polonium-210 and selenium in tissues and tissue extracts of the mussel Mytilus galloprovincialis (Gulf of Trieste).

PubMed

Kristan, Urška; Planinšek, Petra; Benedik, Ljudmila; Falnoga, Ingrid; Stibilj, Vekoslava

2015-01-01

Marine organisms such as mussels and fish take up polonium (Po) and selenium (Se), and distribute them into different cellular components and compartments. Due to its high radiotoxicity and possible biomagnification across the marine food chain Po-210 is potentially hazardous, while selenium is an essential trace element for humans and animals. The aim of this study was to investigate and compare the presence and extractability of the elements in the mussels Mytilus galloprovincialis collected in the Gulf of Trieste. The levels of Po-210 in the samples ranged from 220 to 400 Bq kg(-1) and of Se from 2.6 to 8.2 mg kg(-1), both on a dry matter basis. Using various extraction types and conditions in water, buffer or enzymatic media, the best extractability was obtained with enzymatic extraction (Protease XIV, 1h shaking at 40 °C) and the worst by water extraction (24 h shaking at 37 °C). 90% of Po-210 and 70% of Se was extractable in the first case versus less than 10% of Po-210 and less than 40% of Se in the second. Such evident differences in extractability between the investigated elements point to different metabolic pathways of the two elements. In enzymatic extracts Se speciation revealed three Se compounds (SeCys2, SeMet, one undefined), while Po-210 levels were too low to allow any conclusions about speciation. Copyright © 2014 Elsevier Ltd. All rights reserved.

Phosphate removal from aqueous solution using iron oxides: Adsorption, desorption and regeneration characteristics.

PubMed

Ajmal, Zeeshan; Muhmood, Atif; Usman, Muhammad; Kizito, Simon; Lu, Jiaxin; Dong, Renjie; Wu, Shubiao

2018-05-24

Dynamics of phosphate (PO 4 3- ) adsorption, desorption and regeneration characteristics of three lab-synthesized iron oxides, ferrihydrite (F), goethite (G), and magnetite (M) were evaluated in this study. Batch experiments were conducted to evaluate the impact of several adsorption parameters including adsorbent dosage, reaction time, temperature, pH, and ionic strength. The results showed that PO 4 3- adsorption increased with reaction time and temperature while it decreased with an increase in solution pH. Adsorption isotherm data exhibited good agreement with the Freundlich and Langmuir model with maximum monolayer adsorption capacities of 66.6 mg·g -1 (F), 57.8 mg·g -1 (M), and 50.5 mg·g -1 (G). A thermodynamics evaluation produced ΔG < 0, ΔH > 0, and ΔS > 0, demonstrating that PO 4 3- adsorption onto tested minerals is endothermic, spontaneous, and disordered. The PO 4 3- removal mostly occurred via electrostatic attraction between the sorbate and sorbent surfaces. Moreover, the PO 4 3- sorption was reversible and could be desorbed at varying rates in both neutral and alkaline environments. The good desorption capacity has practical benefits for potential regeneration and re-use of the saturated particles in wastewater treatment systems. Copyright © 2018 Elsevier Inc. All rights reserved.

Influence of limited proteolysis, detergent treatment and lyophilization on the phenoloxidase activity of Rapana thomasiana hemocyanin.

PubMed

Idakieva, Krassimira; Siddiqui, Nurul Islam; Meersman, Filip; De Maeyer, Marc; Chakarska, Irena; Gielens, Constant

2009-08-01

The intrinsic and inducible phenoloxidase (PO) activity of Rapana thomasiana hemocyanin (RtH) and its substructures were studied. With catechol as substrate, a weak o-diPO activity was measured for the didecameric RtH and its subunits. Some activation of the o-diPO activity of RtH was achieved by limited treatment with subtilisin and by incubation of RtH with 2.9 mM sodium dodecyl sulphate (SDS), suggesting an enhanced substrate access to the active sites. The highest artificial induction of o-diPO activity in RtH, however, was obtained by lyophilization of the protein. This is ascribed to conformational changes during the lyophilization process of the didecameric RtH molecules, affecting the accessibility of the active sites. These conformational changes must be very small, since Fourier-transform infrared and circular dichroism spectroscopies did not reveal any changes in secondary structure of lyophilized RtH. The difference in accessibility of the copper containing active site for substrates between catechol oxidase and functional unit RtH2-e was demonstrated by molecular modeling and surface area accessibility calculations. The low level of intrinsic PO activity in the investigated hemocyanin is related to the inaccessibility of the binuclear copper active sites to the substrates.

[Effects of different amounts of phosphate fertilizers on copper, zinc transfer in red soil under the application of KH2PO4].

PubMed

Guo, Liang; Li, Zhong-wu; Huang, Bin; Wang, Yan; Zhang, Yan

2014-09-01

In order to study the effects of different phosphate addition amounts on migration and transformation of heavy metals (Cu, Zn) in soil, an indoor leaching experiment using soil columns was carry out to study the leaching behavior of Cu and Zn. The KH2PO4 was chosen as the fertilizer application at the doses of 5 mg.kg-1, 15 mg.kg-1 and 25 mg.kg-1. The results showed that KH2PO4, could reduce the leachate pH, but different phosphate amounts had little effect on leachate pH, pH in leachate kept rising in the whole leaching process. With the application of KH2PO4, Cu migration was mainly in the surface layer while Zn migrated into deeper soil. Concentrations of Cu, Zn in deep soil leachate were low indicating that it was harmless to the shallow groundwater. After leaching, heavy metals mainly existed in the residual form in soil, the proportion of residual form of Cu was around 60% and the proportion of residual form of Zn was around 40%. High concentration of KH2PO4 helps the transformation of Zn from residual organic combination state to exchange state.

Dosimetry of {sup 210}Po in humans, caribou, and wolves in northern Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, P.A.

1994-06-01

Effective doses from {sup 210}Po intake with caribou meat were determined for human residents in Baker Lake and Snowdrift in the Northwest Territories of Canada and compared to doses calculated from reported {sup 210}Po tissue activities in Alaskan and British residents. Effective doses were calculated to separate body tissues, using ICRP 60 human weighting factors and the ICRP 30 metabolic model for {sup 210}Po. Baker Lake and Alaskan effective doses were similar at 0.4 mSv y{sup {minus}1} and slightly higher than Snowdrift doses (0.3 mSv y{sup {minus}1}). Alaskan tissue activities indicated higher effective doses to liver, bone surfaces and redmore » marrow and lower doses to spleen than the {sup 210}Po metabolic model (ICRP 1979a) predicts. Effective doses to Baker Lake and Snowdrift caribou and wolves, calculated from tissue activities, ranged from 7-20 mSv y{sup {minus}1} using human weighting factors for comparison to human doses only. Effective doses to northern Canadians and wildlife were, respectively, 7-11% and 1.8-5 times an estimated human background of 4 mSv y{sup {minus}} from all sources. 51 refs., 2 figs., 9 tabs.« less

Clean galena, contaminated lead, and soft errors in memory chips

NASA Astrophysics Data System (ADS)

Lykken, G. I.; Hustoft, J.; Ziegler, B.; Momcilovic, B.

2000-10-01

Lead (Pb) disks were exposed to a radon (Rn)-rich atmosphere and surface alpha particle emissions were detected over time. Cumulative 210Po alpha emission increased nearly linearly with time. Conversely, cumulative emission for each of 218Po and 214Po was constant after one and two hours, respectively. Processing of radiation-free Pb ore (galena) in inert atmospheres was compared with processing in ambient air. Galena processed within a flux heated in a graphite crucible while exposed to an inert atmosphere, resulted in lead contaminated with 210Po (Trial 1). A glove box was next used to prepare a baseline radiation-free flux sample in an alumina crucible that was heated in an oven with an inert atmosphere (Trials 2 and 3). Ambient air was thereafter introduced, in place of the inert atmosphere, to the radiation-free flux mixture during processing (Trial 4). Ambient air introduced Rn and its progeny (RAD) into the flux during processing so that the processed Pb contained Po isotopes. A typical coke used in lead smelting also emitted numerous alpha particles. We postulate that alpha particles from tin/lead solder bumps, a cause of computer chip memory soft errors, may originate from Rn and RAD in the ambient air and/or coke used as a reducing agent in the standard galena smelting procedure.

Septic Systems Contribution to Phosphorus in Shallow Groundwater: Field-Scale Studies Using Conventional Drainfield Designs

PubMed Central

Mechtensimer, Sara

2017-01-01

Septic systems can be a potential source of phosphorus (P) in groundwater and contribute to eutrophication in aquatic systems. Our objective was to investigate P transport from two conventional septic systems (drip dispersal and gravel trench) to shallow groundwater. Two new in-situ drainfields (6.1 m long by 0.61 m wide) with a 3.72 m2 infiltrative surface were constructed. The drip dispersal drainfield was constructed by placing 30.5 cm commercial sand on top of natural soil and the gravel trench drainfield was constructed by placing 30.5 cm of gravel on top of 30.5 cm commercial sand and natural soil. Suction cup lysimeters were installed in the drainfields (at 30.5, 61, 106.7 cm below infiltrative surface) and piezometers were installed in the groundwater (>300 cm below infiltrative surface) to capture P dynamics from the continuum of unsaturated to saturated zones in the septic systems. Septic tank effluent (STE), soil-water, and groundwater samples were collected for 64 events (May 2012–Dec 2013) at 2 to 3 days (n = 13), weekly (n = 29), biweekly (n = 17), and monthly (n = 5) intervals. One piezometer was installed up-gradient of the drainfields to monitor background groundwater (n = 15). Samples were analyzed for total P (TP), orthophosphate-P (PO4–P), and other–P (TP—PO4-P). The gravel trench drainfield removed significantly (p<0.0001) greater TP (~20%) than the drip dispersal in the first 30.5 cm of the drainfield. However, when STE reached >300 cm in the groundwater, both systems had similar TP reductions of >97%. After 18 months of STE application, there was no significant increase in groundwater TP concentrations in both systems. We conclude that both drainfield designs are effective at reducing P transport to shallow groundwater. PMID:28107505

Septic Systems Contribution to Phosphorus in Shallow Groundwater: Field-Scale Studies Using Conventional Drainfield Designs.

PubMed

Mechtensimer, Sara; Toor, Gurpal S

2017-01-01

Septic systems can be a potential source of phosphorus (P) in groundwater and contribute to eutrophication in aquatic systems. Our objective was to investigate P transport from two conventional septic systems (drip dispersal and gravel trench) to shallow groundwater. Two new in-situ drainfields (6.1 m long by 0.61 m wide) with a 3.72 m2 infiltrative surface were constructed. The drip dispersal drainfield was constructed by placing 30.5 cm commercial sand on top of natural soil and the gravel trench drainfield was constructed by placing 30.5 cm of gravel on top of 30.5 cm commercial sand and natural soil. Suction cup lysimeters were installed in the drainfields (at 30.5, 61, 106.7 cm below infiltrative surface) and piezometers were installed in the groundwater (>300 cm below infiltrative surface) to capture P dynamics from the continuum of unsaturated to saturated zones in the septic systems. Septic tank effluent (STE), soil-water, and groundwater samples were collected for 64 events (May 2012-Dec 2013) at 2 to 3 days (n = 13), weekly (n = 29), biweekly (n = 17), and monthly (n = 5) intervals. One piezometer was installed up-gradient of the drainfields to monitor background groundwater (n = 15). Samples were analyzed for total P (TP), orthophosphate-P (PO4-P), and other-P (TP-PO4-P). The gravel trench drainfield removed significantly (p<0.0001) greater TP (~20%) than the drip dispersal in the first 30.5 cm of the drainfield. However, when STE reached >300 cm in the groundwater, both systems had similar TP reductions of >97%. After 18 months of STE application, there was no significant increase in groundwater TP concentrations in both systems. We conclude that both drainfield designs are effective at reducing P transport to shallow groundwater.

Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent.

PubMed

Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh; Lee, Byeong-Kyu; Mitoma, Yoshiharu; Mallampati, Srinivasa Reddy

2015-10-15

This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO4 dispersion mixture immobilized 95-100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO4 was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO4 mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO4- associated crystalline complexes, and that immobile Ca/PO4 salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO4 as a simple, suitable and highly efficient material for the gentle immobilization of heavy metals in hazardous ASR thermal residue in dry condition. Copyright © 2015 Elsevier B.V. All rights reserved.

Transfer of ²¹⁰Po, ²¹⁰Pb and ²³⁸U from some medicinal plants to their essential oils.

PubMed

Al-Masri, M S; Amin, Y; Ibrahim, S; Nassri, M

2015-03-01

Essential oils were extracted from 35 medicinal plants used by Syrians, organic compounds were determined in these oils and concentrations of (210)Po (210)Pb and (238)U were determined in the original plants and in the essential oils. The results showed that the highest activity concentrations of (210)Po and (210)Pb were found in leaves with large surfaces and in Sage were as high as 73.5 Bq kg(-1) and 73.2 Bq kg(-1), respectively. The activity concentration of (238)U was as high as 4.26 Bq kg(-1) in Aloe. On the other hand, activity concentrations of (210)Po ranged between 0.2 and 71.1 Bq kg(-1) in extracted essential oils for Rosemary and False yellowhead, respectively. The activity concentration of (210)Pb reached 63.7 Bq kg(-1) in Aloe oil. The activity concentrations of (238)U were very low in all extracted oils; the highest value was 0.31 Bq kg(-1) in peel of Orange oil. The transfer of (210)Po and (210)Pb from plant to its oil was the highest for Eugenia; 7.1% and 5.5% for (210)Po and (210)Pb, respectively. A linear relationship was found between the transfer factor of radionuclides from plant to its essential oil and the chemical content of this oil. Copyright © 2014 Elsevier Ltd. All rights reserved.

Scavenging and fractionation of particle-reactive radioisotopes 7Be, 210Pb and 210Po in the atmosphere

NASA Astrophysics Data System (ADS)

Chen, Jinfang; Luo, Shangde; Huang, Yipu

2016-09-01

The scavenging and fractionation of 7Be, 210Pb, and 210Po in the atmosphere are investigated by measuring their activities in rainwater collected from 68 rain events during March 2004 to April 2006 at a coastal station of Xiamen, southeastern China. In addition to documenting the large temporal variations in activities, fluxes, and isotope ratios of 7Be, 210Pb and 210Po in rainwater and the role of rainfall intensity in radionuclide scavenging, our results show that an enhanced deposition of 7Be and 210Pb occurs in the spring than in other seasons and is attributed to the "funnel effect" due to the increased atmospheric vertical convective mixing in the spring. This latter hypothesis is further supported by the observed seasonal and inter-annual variations in 7Be/210Pb and 210Po/210Pb ratios showing that the weakening of vertical convective mixing or stratosphere-troposphere exchange (STE) at the study site is linked with the enhancement of summer monsoons. It appears that the rainfall intensity, in connection with the vertical (e.g., STE) and horizontal (summer monsoons) air transport, exerts an important control on the activities, fluxes, and isotope ratios of 7Be, 210Pb, and 210Po in the atmosphere. Application of the observational data to a theoretical model shows that there are significant fractionations among 7Be, 210Pb, and 210Po in the atmosphere, with the scavenging rate constant or reciprocal of the residence time of radionuclide in the atmosphere being 210Pb > 7Be > 210Po. A revised Poet et al. (1972)'s method is proposed for quantitative constraint on the scavenging behavior of radionuclide, aerosols, and aerosol-associated trace pollutants in the atmosphere.

Polydeoxyribonucleotides and nitric oxide release from guinea-pig hearts during ischaemia and reperfusion.

PubMed Central

Masini, E.; Lupini, M.; Mugnai, L.; Raspanti, S.; Mannaioni, P. F.

1995-01-01

1. Two polydeoxyribonucleotides, produced by the controlled hydrolysis of DNA of mammalian lung (defibrotide and its lower molecular weight fraction, P.O. 085 DV), were studied for their ability to modify the release of nitrite and the coronary flow in perfusates collected from isolated, normally perfused hearts of guinea-pigs and from hearts subjected to regional ischaemia and reperfusion. 2. In guinea-pig normally perfused hearts, both defibrotide (DFT) and its fraction, P.O. 085 DV, increase the amount of nitrite appearing in perfusates in a concentration-dependent fashion. At the highest concentration studied (10(-6) M), P.O. 085 DV was more effective than DFT. A concomitant increase in the coronary flow was observed. 3. The increase in nitrite in perfusates and the increase in coronary flow induced by both DFT and P.O. 085 DV were significantly reduced by NG-monomethyl-L-arginine (L-NMMA, 10(-4) M), an inhibitor of nitric oxide synthase (NOS). 4. The endothelium-dependent vasodilator, acetylcholine (ACh), enhances the formation of nitrite and the coronary flow. Both the increase in coronary flow and in the formation of nitrite were significantly reduced by L-NMMA (10(-4) M). 5. In guinea-pig hearts subjected to ischaemia and reperfusion, the effect of both compounds in increasing the amount of nitrite in perfusates was more evident and more pronounced with P.O. 085 DV. 6. Reperfusion-induced arrhythmias were significantly reduced by both compounds to the extent of complete protection afforded by compound P.O. 085 DV. 7. The cardioprotective and antiarrhythmic effects of DFT and P.O. 085 DV are discussed. PMID:7582482

Posterior paramedian subrhomboidal analgesia versus thoracic epidural analgesia for pain control in patients with multiple rib fractures.

PubMed

Shelley, Casey L; Berry, Stepheny; Howard, James; De Ruyter, Martin; Thepthepha, Melissa; Nazir, Niaman; McDonald, Tracy; Dalton, Annemarie; Moncure, Michael

2016-09-01

Rib fractures are common in trauma admissions and are associated with an increased risk of pulmonary complications, intensive care unit admissions, and mortality. Providing adequate pain control in patients with multiple rib fractures decreases the risk of adverse events. Thoracic epidural analgesia is currently the preferred method for pain control. This study compared outcomes in patients with multiple acute rib fractures treated with posterior paramedian subrhomboidal (PoPS) analgesia versus thoracic epidural analgesia (TEA). This prospective study included 30 patients with three or more acute rib fractures admitted to a Level I trauma center. Thoracic epidural analgesia or PoPS catheters were placed, and local anesthesia was infused. Data were collected including patients' pain level, adjunct morphine equivalent use, adverse events, length of stay, lung volumes, and discharge disposition. Nonparametric tests were used and two-sided p < 0.05 were considered statistically significant. Nineteen (63%) of 30 patients received TEA and 11 (37%) of 30 patients received PoPS. Pain rating was lower in the PoPS group (2.5 vs. 5; p = 0.03) after initial placement. Overall, there was no other statistically significant difference in pain control or use of oral morphine adjuncts between the groups. Hypotension occurred in eight patients, 75% with TEA and only 25% with PoPS. No difference was found in adverse events, length of stay, lung volumes, or discharge disposition. In patients with rib fractures, PoPS analgesia may provide pain control equivalent to TEA while being less invasive and more readily placed by a variety of hospital staff. This pilot study is limited by its small sample size, and therefore additional studies are needed to prove equivalence of PoPS compared to TEA. Therapeutic study, level IV.

Radionuclides in resident and migratory fishes of a wedge bank region: Estimation of dose to human beings, South India.

PubMed

Khan, M Feroz; Wesley, S Godwin

2012-10-01

Baseline activity concentration of (137)Cs, (210)Po and (210)Pb was determined for 25 resident and 22 migratory fish species collected in a so-called wedge bank region in the extreme south of India. A nuclear power station is now under construction at Kudankulam near the target region and the data provide background information on the radionuclide activity concentration in the region. Three-way ANOVA revealed no significant variation in the concentrations of (137)Cs, (210)Po and (210)Pb between species based on feeding habit, habitat and migratory pattern except the effect of feeding habit on (210)Po concentration (p<0.05). The annual dose due to radionuclide ingestion through the fishes was calculated based on the survey results of fish consumption rates for the local population. The dose due to (137)Cs was negligibly small while those due to (210)Po and (210)Pb varied from 1.2 to 36.9 and 0.2 to 2.9μSv yr(-1), respectively. Copyright © 2012 Elsevier Ltd. All rights reserved.

Point of view filming and the elicitation interview.

PubMed

Skinner, Jonathan; Gormley, Gerard J

2016-08-01

Face-to-face interviews are a fundamental research tool in qualitative research. Whilst this form of data collection can provide many valuable insights, it can often fall short of providing a complete picture of a research subject's experiences. Point of view (PoV) interviewing is an elicitation technique used in the social sciences as a means of enriching data obtained from research interviews. Recording research subjects' first person perspectives, for example by wearing digital video glasses, can afford deeper insights into their experiences. PoV interviewing can promote making visible the unverbalizable and does not rely as much on memory as the traditional interview. The use of such relatively inexpensive technology is gaining interest in health profession educational research and pedagogy, such as dynamic simulation-based learning and research activities. In this interview, Dr Gerry Gormley (a medical education researcher) talks to Dr Jonathan Skinner (an anthropologist with an interest in PoV interviewing), exploring some of the many crossover implications with PoV interviewing for medical education research and practice.

Three-dimensional Frankfort horizontal plane for 3D cephalometry: a comparative assessment of conventional versus novel landmarks and horizontal planes.

PubMed

Pittayapat, Pisha; Jacobs, Reinhilde; Bornstein, Michael M; Odri, Guillaume A; Lambrichts, Ivo; Willems, Guy; Politis, Constantinus; Olszewski, Raphael

2018-05-25

To assess the reproducibility of landmarks in three dimensions that determine the Frankfort horizontal plane (FH) as well as two new landmarks, and to evaluate the angular differences of newly introduced planes to the FH. Three-dimensional (3D) surface models were created from CBCT scans of 26 dry human skulls. Porion (Po), orbitale (Or), internal acoustic foramen (IAF), and zygomatico-maxillary suture (ZyMS) were indicated in the software by three observers twice with a 4-week interval. Angles between two FHs (FH 1: Or-R, Or-L, mid-Po; FH 2: Po-R, Po-L, mid-Or) and between FHs and new planes (Plane 1-6) were measured. Coordinates were exported to a spreadsheet. A statistical analysis was performed to define the landmark reproducibility and 3D angles. Intra- and inter-observer landmark reproducibility showed mean difference more than 1 mm for x-coordinates of all landmarks except IAF. IAF showed significantly better reproducibility than other landmarks (P < 0.0018). The mean angular difference between FH 1 and FH 2 was 0.7 degrees. Plane 3, connecting Or-R, Or-L and mid-IAF, and Plane 4, connecting Po-R, Po-L and mid-ZyMS, both showed an angular difference of less than 1 degree when compared to FHs. This study revealed poor reproducibility of the traditional FH landmarks on the x-axis and good reproducibility of a new landmark tested to replace Po, the IAF. Yet, Or showed superior results compared to ZyMS. The potential of using new horizontal planes was demonstrated. Future studies should focus on identification of a valid alternative for Or and ZyMS and on clinical implementation of the findings.

Secondary ion generation mechanism studied by ISS-SIMS and work function measurements

NASA Astrophysics Data System (ADS)

Kawatoh, Eizoh; Terada, Norihito; Shimizu, Ryuichi; Kang, Hee Jae

1989-03-01

Oxygen enhancement effects in secondary ion generation were studied in polycrystalline Ni at different partial pressures of oxygen, Po2, by sequential ISS-SIMS and work function measurements. The investigation has revealed that the enhancement undergoes three stages: (I) The secondary ion intensity increases monotonically with an increase of work function which is described very well by the electron tunneling model. (II) This tendency abruptly changes, i.e. the work function decreases and the secondary ion intensity increases rapidly, for a slight increase of Po2 (III) The secondary ion intensities gradually increase and become saturated with a further increase of Po2. It has also been found that the critical coverage, θc, corresponds exactly to the stage (II) behaviour, which was observed by Blaise and Bernheim for a single crystal (100)Ni surface.

Surface-enhanced Raman spectroscopy competitive binding biosensor development utilizing surface modification of silver nanocubes and a citrulline aptamer

NASA Astrophysics Data System (ADS)

Walton, Brian M.; Jackson, George W.; Deutz, Nicolaas; Cote, Gerard

2017-07-01

A point-of-care (PoC) device with the ability to detect biomarkers at low concentrations in bodily fluids would have an enormous potential for medical diagnostics outside the central laboratory. One method to monitor analytes at low concentrations is by using surface-enhanced Raman spectroscopy (SERS). In this preliminary study toward using SERS for PoC biosensing, the surface of colloidal silver (Ag) nanocubes has been modified to test the feasibility of a competitive binding SERS assay utilizing aptamers against citrulline. Specifically, Ag nanocubes were functionalized with mercaptobenzoic acid, as well as a heterobifunctional polyethylene glycol linker that forms an amide bond with the amino acid citrulline. After the functionalization, the nanocubes were characterized by zeta-potential, transmission electron microscopy images, ultraviolet/visible spectroscopy, and by SERS. The citrulline aptamers were developed and tested using backscattering interferometry. The data show that our surface modification method does work and that the functionalized nanoparticles can be detected using SERS down to a 24.5 picomolar level. Last, we used microscale thermophoresis to show that the aptamers bind to citrulline with at least a 50 times stronger affinity than other amino acids.

Efficient Degradation of Malathion in the Presence of Detergents Using an Engineered Organophosphorus Hydrolase Highly Expressed by Pichia pastoris without Methanol Induction.

PubMed

Bai, Yun-Peng; Luo, Xiao-Jing; Zhao, Yu-Lian; Li, Chun-Xiu; Xu, Dian-Sheng; Xu, Jian-He

2017-10-18

The biodegradation of pesticides by organophosphorus hydrolases (OPHs) requires an efficient enzyme production technology in industry. Herein, a Pichia pastoris strain was constructed for the extracellular expression of PoOPH M9 , an engineered malathion-degrading enzyme. After optimization, the maximum titer and yield of fermentation reached 50.8 kU/L and 4.1 g protein /L after 3 days, with the highest space-time yield (STY) reported so far, 640 U L -1 h -1 . PoOPH M9 displayed its high activity and stability in the presence of 0.1% (w/w) plant-derived detergent. Only 0.04 mg/mL enzyme could completely remove 0.15 mM malathion in aqueous solution within 20 min. Furthermore, 12 μmol malathion on apples and cucumbers surfaces was completely removed by 0.05 mg/mL PoOPH M9 in tap water after 35 min washing. The efficient production of the highly active PoOPH M9 has cleared a major barrier to biodegradation of pesticide residues in food industry.

Tools, Services & Support of NASA Salinity Mission Data Archival Distribution through PO.DAAC

NASA Astrophysics Data System (ADS)

Tsontos, V. M.; Vazquez, J.

2017-12-01

The Physical Oceanography Distributed Active Center (PO.DAAC) serves as the designated NASA repository and distribution node for all Aquarius/SAC-D and SMAP sea surface salinity (SSS) mission data products in close collaboration with the projects. In addition to these official mission products, that by December 2017 will include the Aquarius V5.0 end-of-mission data, PO.DAAC archives and distributes high-value, principal investigator led satellite SSS products, and also datasets from NASA's "Salinity Processes in the Upper Ocean Regional Study" (SPURS 1 & 2) field campaigns in the N. Atlantic salinity maximum and high rainfall E. Tropical Pacific regions. Here we report on the status of these data holdings at PO.DAAC, and the range of data services and access tools that are provided in support of NASA salinity. These include user support and data discovery services, OPeNDAP and THREDDS web services for subsetting/extraction, and visualization via LAS and SOTO. Emphasis is placed on newer capabilities, including PODAAC's consolidated web services (CWS) and advanced L2 subsetting tool called HiTIDE.

Palmitic acid in the sn-2 position of dietary triacylglycerols does not affect insulin secretion or glucose homeostasis in healthy men and women

PubMed Central

Filippou, A; Teng, K-T; Berry, S E; Sanders, T A B

2014-01-01

Background/objectives: Dietary triacylglycerols containing palmitic acid in the sn-2 position might impair insulin release and increase plasma glucose. Subjects/Methods: We used a cross-over designed feeding trial in 53 healthy Asian men and women (20–50 years) to test this hypothesis by exchanging 20% energy of palm olein (PO; control) with randomly interesterified PO (IPO) or high oleic acid sunflower oil (HOS). After a 2-week run-in period on PO, participants were fed PO, IPO and HOS for 6 week consecutively in randomly allocated sequences. Fasting (midpoint and endpoint) and postprandial blood at the endpoint following a test meal (3.54 MJ, 14 g protein, 85 g carbohydrate and 50 g fat as PO) were collected for the measurement of C-peptide, insulin, glucose, plasma glucose-dependent insulinotropic polypeptide and glucagon-like peptide-1, lipids and apolipoproteins; pre-specified primary and secondary outcomes were postprandial changes in C-peptide and plasma glucose. Results: Low density lipoprotein cholesterol was 0.3 mmol/l (95% confidence interval (95% CI)) 0.1, 0.5; P<0.001) lower on HOS than on PO or IPO as predicted, indicating good compliance to the dietary intervention. There were no significant differences (P=0.58) between diets among the 10 male and 31 female completers in the incremental area under the curve (0–2 h) for C-peptide in nmol.120 min/l: GM (95% CI) were PO 220 (196, 245), IPO 212 (190, 235) and HOS 224 (204, 244). Plasma glucose was 8% lower at 2 h on IPO vs PO and HOS (both P<0.05). Conclusion: Palmitic acid in the sn-2 position does not adversely impair insulin secretion and glucose homeostasis. PMID:25052227

NASA's New Science Education and Public Outreach Forums: Bringing Communities and Resources Together to Increase Effectiveness and Sustainability

NASA Astrophysics Data System (ADS)

Smith, Denise A.; Mendez, B.; Shipp, S.; Schwerin, T.; Stockman, S.; Cooper, L. P.; Sharma, M.

2010-01-01

Scientists, engineers, educators, and public outreach professionals have a rich history of creatively using NASA's pioneering scientific discoveries and technology to engage and educate youth and adults nationwide in core science, technology, engineering, and mathematics topics. We introduce four new Science Education and Public Outreach Forums that will work in partnership with the community and NASA's Science Mission Directorate (SMD) to ensure that current and future SMD-funded education and public outreach (E/PO) activities form a seamless whole, with easy entry points for general public, students, K-12 formal and informal science educators, faculty, scientists, engineers, and E/PO professionals alike. The new Science Education and Public Outreach Forums support the astrophysics, heliophysics, planetary and Earth science divisions of NASA SMD in three core areas: 1) E/PO community engagement and development activities will provide clear paths of involvement for scientists and engineers interested - or potentially interested - in participating in SMD-funded E/PO activities. Collaborations with scientists and engineers are vital for infusing current, accurate SMD mission and research findings into educational products and activities. Forum activities will also yield readily accessible information on effective E/PO strategies, resources, and expertise; context for individual E/PO activities; and opportunities for collaboration. 2) A rigorous analysis of SMD-funded K-12 formal, informal, and higher education products and activities will help the community and SMD to understand how the existing collection supports education standards and audience needs, and to strategically identify areas of opportunity for new materials and activities. 3) Finally, a newly convened Coordinating Committee will work across the four SMD science divisions to address systemic issues and integrate related activities. By supporting the NASA E/PO community and facilitating coordination of E/PO activities, the NASA-SEPOF partnerships will lead to more effective, sustainable, and efficient utilization of NASA science discoveries and learning experiences.

Redox process catalysed by growing crystal-strengite, FePO4,2H2O, crystallizing from solution with iron(II) and hydroxylamine

NASA Astrophysics Data System (ADS)

Lundager Madsen, Hans Erik

2014-09-01

In an attempt to grow pure crystals of the iron(II) phosphate vivianite, Fe3(PO4)2,8H2O, from a solution of Mohr's salt, Fe(NH4)2(SO4)2,6H2O, added to a solution of ammonium phosphate, hydroxylammonium chloride, NH3OHCl, was added to the iron(II) stock solution to eliminate oxidation of iron(II) by oxygen from the air. However, the effect turned out to be the opposite of the expected: whereas hydroxylamine reduces iron(III) in bulk solution, it acted as a strong oxidant in the presence of growing iron phosphate crystals, causing the crystallization of the iron(III) phosphate strengite, FePO4,2H2O, as the only solid phase. Evidently the crystal surface catalyses oxidation of iron(II) by hydroxylamine. The usual composite kinetics of spiral growth and surface nucleation was found. The surface-nucleation part yielded edge free energy λ in the range 12-45 pJ/m, virtually independent of temperature and in the range typical for phosphates of divalent metals. The scatter of values for λ presumably arises from contributions from different crystal forms to the overall growth rate. The low mean value points to strong adsorption of iron(II), which is subsequently oxidized at the crystal surface, forming strengite. The state of the system did not tend to thermodynamic equilibrium, but to a metastable state, presumably controlled by the iron(II) rich surface layer of the crystal. In addition to crystal growth, it was possible to measure nucleation kinetics by light scattering (turbidimetry). A point of transition from heterogeneous to homogeneous nucleation was found, and from the results for the homogeneous domain a rather precise value of crystal surface free energy γ=55 mJ/m2 was found. This is a relatively low value as well, indicating that the redox process plays a role already at the nucleation stage.

Nitrogen-doped hierarchical porous carbon with high surface area derived from graphene oxide/pitch oxide composite for supercapacitors.

PubMed

Ma, Yuan; Ma, Chang; Sheng, Jie; Zhang, Haixia; Wang, Ranran; Xie, Zhenyu; Shi, Jingli

2016-01-01

A nitrogen-doped hierarchical porous carbon has been prepared through one-step KOH activation of pitch oxide/graphene oxide composite. At a low weight ratio of KOH/composite (1:1), the as-prepared carbon possesses high specific surface area, rich nitrogen and oxygen, appropriate mesopore/micropore ratio and considerable small-sized mesopores. The addition of graphene oxide plays a key role in forming 4 nm mesopores. The sample PO-GO-16 presents the characteristics of large surface area (2196 m(2) g(-1)), high mesoporosity (47.6%), as well as rich nitrogen (1.52 at.%) and oxygen (6.9 at.%). As a result, PO-GO-16 electrode shows an outstanding capacitive behavior: high capacitance (296 F g(-1)) and ultrahigh-rate performance (192 F g(-1) at 10 A g(-1)) in 6 M KOH aqueous electrolyte. The balanced structure characteristic, low-cost and high performance, make the porous carbon a promising electrode material for supercapacitors. Copyright © 2015 Elsevier Inc. All rights reserved.

Miscibility Gap Closure, Interface Morphology, and Phase Microstructure of 3D Li xFePO 4 Nanoparticles from Surface Wetting and Coherency Strain

DOE PAGES

Welland, Michael J.; Karpeyev, Dmitry; O’Connor, Devin T.; ...

2015-09-10

We study the mesoscopic effects which suppress phase-segregation in Li xFePO 4 nanoparticles using a multiphysics phase-field model implement on a high performance cluster. We simulate 3D spherical particles of radii from 3nm to 40nm and examine the equilibrium microstructure and voltage profiles as a they depend on size and overall lithiation. The model includes anisotropic, concentration-dependent elastic moduli, misfit strain, and facet dependent surface wetting within a Cahn-Hilliard formulation. Here, we find that the miscibility gap vanishes for particles of radius ~ 5 nm, and the solubility limits change with overall particle lithiation. The corresponding voltage plateau, indicative ofmore » phase-segregation, changes in extent and also vanishes. Surface wetting is found to have a strong effect on stabilizing a variety of microstructures, exaggerating the shifting of solubility limits, and shortening the voltage plateau.« less

Hydrogeochemical characterization of the phreatic system of the coastal wetland located between Fiumi Uniti and Bevano rivers in the southern Po plain (Northern Italy).

NASA Astrophysics Data System (ADS)

Marconi, V.; Dinelli, E.; Antonellini, M.; Capaccioni, B.; Balugani, E.; Gabbianelli, G.

2009-04-01

A hydrogeochemical study has been undertaken on the phreatic system of the coastal area included between Fiumi Uniti and Bevano rivers (in the southern part of the Po plain, near the city of Ravenna) within the framework of the CIRCLE-ERANET project WATERKNOW on the effects of climate change on the mediterranean catchments. It is one of the first attempt in the area to characterize the shallow groundwater water system and to investigate if the arsenic anomaly, known in deeper groundwater (about 100 µg/l according to recent Annual Groundwater Quality Reports of Emilia-Romagna Region), occurs also in the phreatic system. The coastal part of the Po plain consists of a low-lying and mechanically-drained farmland further from the sea and of a narrow belt of dunes and pine forests in the backshore area. The study area is recognized as a protected area at european (ZPS and SIC, site code number: IT 14070009), national and regional level (Po delta Park area). As a result of an intensive exploitation of coastal aquifers for agricultural, industrial, and civil uses, both the phreatic aquifer and the surface waters (drainage ditches and ponds) have been contaminated by seawater and by deeper groundwater. Samples representative of the top of the water table were collected in Summer 2008 in 22 auger-holes and in 3 shallow piezometers (6 m deep) documenting the deeper layers of the phreatic groundwater system. Temperature, electrical conductivity, pH and Eh of the groundwater and of the surface water were measured on site using portable instruments. Samples were filtered directly in the field, an aliquot was acidified with diluted HCl for metal analysis. Cations were determined by Flame Atomic Absorption (thermo S-series spectrometer), anions by ion chromatography (Dionex ICS-90), Fe, As, Si, B by ICP-OES (Thermo iCAP6000). The data collected in the field show that a fresh groundwater lens is still present at the top of the phreatic aquifer in the backshore area and that the surface water is all brackish to salty and characterised by negative values of Eh, which is probably due to the low hydraulic gradients of the area. Hydrochemistry indicates that a simple mixing model does not completely account for the observed groundwater chemistry, thus a more complex and dynamic system must be invoked. The interaction between saltwater and freshwater could be possibly complicated by contributions from deeper and older connate waters and, considering the type of water sample, by precipitation-dissolution reactions taking place in the vadose zone. Application of the BEX (Base Exchange Index, Stuyfzand, 1993), corrected for the occurrence of dolomite in the aquifer, indicate that a salinization processes is taking place in the largest part of the studied area and only in few locations close to the Fiumi Uniti river mouth there are geochemical evidences of freshening probably because there is a different geological situation: silt-clay lenses containing exchangeable minerals are intercalated and/or overlying the sandy aquifer. However an influence of the river on groundwater chemistry cannot be at present completely excluded for the proximity of these sites to the river. Apart groundwater salinization another major environmental problem concerning water quality is represented by elevated Arsenic concentrations. The element display a good negative correlation with Eh but no evident sign of correlation with other measured parameters. Observed arsenic concentrations reach a maximum of 42 µg/l in an auger-hole close to a pond, which is characterized by abundant precipitation of iron hydroxides in the hyporheic zone as well as most of the others surface water bodies. Other relatively high concentration (about 60 µg/l ) are observed in a piezometer (screen depth of 5 m) in the southern area. The ongoing salinization process and the detected anomalies in Arsenic in the phreatic aquifer and in surface water are jeopardizing this wetland ecosystem, which poses a major environmental issue for phreatic water management in the coast. Stuyfzand, P.J. 1993. Hydrochemistry and hydrology of the coastal dune area of the Western Netherlands. Ph.D Thesis Vrije Univ. Amsterdam, KIWA, ISBN 90-74741-01-0, 366 p.

Rapid preparation of high electrochemical performance LiFePO4/C composite cathode material with an ultrasonic-intensified micro-impinging jetting reactor.

PubMed

Dong, Bin; Huang, Xiani; Yang, Xiaogang; Li, Guang; Xia, Lan; Chen, George

2017-11-01

A joint chemical reactor system referred to as an ultrasonic-intensified micro-impinging jetting reactor (UIJR), which possesses the feature of fast micro-mixing, was proposed and has been employed for rapid preparation of FePO 4 particles that are amalgamated by nanoscale primary crystals. As one of the important precursors for the fabrication of lithium iron phosphate cathode, the properties of FePO 4 nano particles significantly affect the performance of the lithium iron phosphate cathode. Thus, the effects of joint use of impinging stream and ultrasonic irradiation on the formation of mesoporous structure of FePO 4 nano precursor particles and the electrochemical properties of amalgamated LiFePO 4 /C have been investigated. Additionally, the effects of the reactant concentration (C=0.5, 1.0 and 1.5molL -1 ), and volumetric flow rate (V=17.15, 51.44, and 85.74mLmin -1 ) on synthesis of FePO 4 ·2H 2 O nucleus have been studied when the impinging jetting reactor (IJR) and UIJR are to operate in nonsubmerged mode. It was affirmed from the experiments that the FePO 4 nano precursor particles prepared using UIJR have well-formed mesoporous structures with the primary crystal size of 44.6nm, an average pore size of 15.2nm, and a specific surface area of 134.54m 2 g -1 when the reactant concentration and volumetric flow rate are 1.0molL -1 and 85.74mLmin -1 respectively. The amalgamated LiFePO 4 /C composites can deliver good electrochemical performance with discharge capacities of 156.7mAhg -1 at 0.1C, and exhibit 138.0mAhg -1 after 100 cycles at 0.5C, which is 95.3% of the initial discharge capacity. Copyright © 2017. Published by Elsevier B.V.

Biochar produced from oak sawdust by Lanthanum (La)-involved pyrolysis for adsorption of ammonium (NH4(+)), nitrate (NO3(-)), and phosphate (PO4(3-)).

PubMed

Wang, Zhanghong; Guo, Haiyan; Shen, Fei; Yang, Gang; Zhang, Yanzong; Zeng, Yongmei; Wang, Lilin; Xiao, Hong; Deng, Shihuai

2015-01-01

A series of biochars were prepared by pyrolyzing oak sawdust with/without LaCl3 involvement at temperature of 300-600 °C, and approximate and ultimate analyses were carried out to check their basic characteristics. Meanwhile, the releases of readily soluble NH4(+), NO3(-) and PO4(3-) from biochars and the adsorption of NH4(+), NO3(-) and PO4(3-) by biochars were investigated. Results indicated that the involvement of LaCl3 in pyrolysis could advance the temperature of maximum mass loss by 10 °C compared with oak sawdust (CK), and potentially promoted biochar yield. Overall, the releases of readily soluble NH4(+), NO3(-) and PO4(3-) from biochars were negatively related to pyrolysis temperature, and the releases were greatly weakened by La-biochars. Additionally, the adsorption to NH4(+) can be promoted by the biochars produced at low temperature. On the contrary, the NO3(-) adsorption can be improved by increasing pyrolysis temperature. The highest PO4(3-) adsorption was achieved by the biochars produced at 500 °C. According to the results of adsorption isotherms, the maximum adsorption capacity of NH4(+), NO3(-) and PO4(3-) can be significantly promoted by 1.9, 11.2, and 4.5 folds using La-biochars. Based on the observations of FT-IR, SEM-EDS, and surface functional groups, the improvement of NH4(+) adsorption was potentially associated with the existing acidic function groups (phenolic-OH and carboxyl C=O). The increased basic functional groups on La-biochars were beneficial to improve NO3(-) and PO4(3-) adsorption. Besides, PO4(3-) adsorption was also potentially related to the formed La2O3. Copyright © 2014 Elsevier Ltd. All rights reserved.

Polonium-210 accumulates in a lake receiving coal mine discharges-anthropogenic or natural?

PubMed

Nelson, A W; Eitrheim, E S; Knight, A W; May, D; Wichman, M D; Forbes, T Z; Schultz, M K

2017-02-01

Coal is an integral part of global energy production; however, coal mining is associated with numerous environmental health impacts. It is well documented that coal-mine waste can contaminate the environment with naturally-occurring radionuclides from the uranium-238 ( 238 U) decay series. However, the behavior of the final radionuclide in the 238 U-series, i.e., polonium-210 ( 210 Po) arising from coal-mine waste-water discharge is largely unexplored. Here, results of a year-long (2014-2015) field study, in which the concentrations of 210 Po in sediments and surface water of a lake that receives coal-mine waste-water discharge in West Virginia are presented. Initial measurements identified levels of 210 Po in the lake sediments that were in excess of that which could be attributed to ambient U-series parent radionuclides; and were indicative of discharge site contamination of the lake ecosystem. However, control sediment obtained from a similar lake system in Iowa (an area with no coal mining or unconventional drilling) suggests that the levels of 210 Po in the lake are a natural phenomenon; and are likely unrelated to waste-water treatment discharges. Elevated levels of 210 Po have been reported in lake bottom sediments previously, yet very little information is available on the radioecological implications of 210 Po accumulation in lake bottom sediments. The findings of this study suggest that (Monthly Energy Review, 2016) the natural accumulation and retention of 210 Po in lake sediments may be a greater than previously considered (Chadwick et al., 2013) careful selection of control sites is important to prevent the inappropriate attribution of elevated levels of NORM in lake bottom ecosystems to industrial sources; and (Van Hook, 1979) further investigation of the source-terms and potential impacts on elevated 210 Po in lake-sediment ecosystems is warranted. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of calcium and phosphate on uranium(IV) oxidation: Comparison between nanoparticulate uraninite and amorphous UIV-phosphate

NASA Astrophysics Data System (ADS)

Latta, Drew E.; Kemner, Kenneth M.; Mishra, Bhoopesh; Boyanov, Maxim I.

2016-02-01

The mobility of uranium in subsurface environments depends strongly on its redox state, with UIV phases being significantly less soluble than UVI minerals. This study compares the oxidation kinetics and mechanisms of two potential products of UVI reduction in natural systems, a nanoparticulate UO2 phase and an amorphous UIV-Ca-PO4 analog to ningyoite (CaUIV(PO4)2·1-2H2O). The valence of U was tracked by X-ray absorption near-edge spectroscopy (XANES), showing similar oxidation rate constants for UIVO2 and UIV-phosphate in solutions equilibrated with atmospheric O2 and CO2 at pH 7.0 (kobs,UO2 = 0.17 ± 0.075 h-1 vs. kobs,UIVPO4 = 0.30 ± 0.25 h-1). Addition of up to 400 μM Ca and PO4 decreased the oxidation rate constant by an order of magnitude for both UO2 and UIV-phosphate. The intermediates and products of oxidation were tracked by electron microscopy, powder X-ray diffraction (pXRD), and extended X-ray absorption fine-structure spectroscopy (EXAFS). In the absence of Ca or PO4, the product of UO2 oxidation is Na-uranyl oxyhydroxide (under environmentally relevant concentrations of sodium, 15 mM NaClO4 and low carbonate concentration), resulting in low concentrations of dissolved UVI (<2.5 × 10-7 M). Oxidation of UIV-phosphate produced a Na-autunite phase (Na2(UO2)PO4·xH2O), resulting in similarly low dissolved U concentrations (<7.3 × 10-8 M). When Ca and PO4 are present in the solution, the EXAFS data and the solubility of the UVI phase resulting from oxidation of UO2 and UIV-phosphate are consistent with the precipitation of Na-autunite. Bicarbonate extractions and Ca K-edge X-ray absorption spectroscopy of oxidized solids indicate the formation of a Ca-UVI-PO4 layer on the UO2 surface and suggest a passivation layer mechanism for the decreased rate of UO2 oxidation in the presence of Ca and PO4. Interestingly, the extractions were unable to remove all of the oxidized U from partially oxidized UO2 solids, suggesting that oxidized U is distributed between the interior of the UO2 nanoparticles and the labile surface layer. Accounting for the entire pool of oxidized U by XANES is the likely reason for the higher UO2 oxidation rate constants determined here relative to prior studies. Our results suggest that the natural presence or addition of Ca and PO4 in groundwater could slow the rates of UIV oxidation, but that the rates are still fast enough to cause complete oxidation of UIV within days under fully oxygenated conditions.

Enriching of surface water in nutrients and DOC on the area of drained Kuwasy Mire in North-East Poland

NASA Astrophysics Data System (ADS)

Jaszczyński, Jacek; Sapek, Andrzej

2010-05-01

Key words: peatlands, drained areas, surface water, nutrients and DOC in water The object of this study was fundamental mineral component concentration (N-NO3, N-NH4, PO4, K, Na, Ca, Mg, Cl, Fe) and dissolved organic carbon concentration (DOC) in surface water in artificial canal running across drained fen area. Also pH, electrical conductivity and abssorbance A280 in water samples were measured. The investigations were localized on the area of drained and agricultural used Kuwasy Mire, which are situated in the middle basin of Biebrza River, in North-East Poland. Currently on the object there is superiority of peat-moorsh soils with moorsh layers to 25 cm of depth. The bog depth is determined from 60 to 140 cm. The most of area is occupied by soils with 110-120 cm organic layer which are intensive agricultural used. Mean annual ground water table amounted 55 cm. On the distance of 8 km (about 1100-1200 ha catchment area) fen space is crossed by Kuwaski Canal collecting water from draining network above describing peatland. Surface water samples were collected every month in three constant point of canal: at entrance on peatland (upper point) in the middle part (middle point) and in border part of peatland (lower point). The study was carried out in 2001-2009. The aim of this study was to determine enriching of surface water in individual mineral and organic components during flowing across peatland area. Mean concentration in whole research period for all investigated components was higher together with flowing of water in canal across fen area. The higest increments of mean concentration between upper a lower point of canal was connected with phosphorous and amonia. The concentrations of these compounds were adequately 4,8 i 2,6 times higher in lower part of canal. Mean concentrations of remaining compounds were 2-14% higher in water in lower point in comparision to upper point of canal. In course of interflow through peatland pH of water was decreasing but electrical conductivity and abssorbance A280 were increasing. When we take into consideration annual quantity of water flowing by canal only on biological level (0,5 m3/s) the increments load of PO4 in this distance amounted 3,6; N-NH4 - 4,6; N-NO3 - 3,0; DOC - 9,5 t.year-1. At mean interflow 3 m3/s the load of describing components was increasing to 21, 27, 20 i 57 t.year-1 in research part of canal.

Nutrient exports from watersheds with varying septic system densities in the North Carolina Piedmont.

PubMed

Iverson, G; Humphrey, C P; O'Driscoll, M A; Sanderford, C; Jernigan, J; Serozi, B

2018-04-01

Septic systems (SSs) have been shown to be a significant source of nitrogen and phosphorus to nutrient-sensitive coastal surface and groundwaters. However, few published studies have quantified the effects of SSs on nutrient inputs to water supply watersheds in the Piedmont region of the USA. This region consists of rolling hills at the surface underlain by clayey soils. There are nearly 1 million SSs in this region, which accounts for approximately 50% of all SSs in North Carolina. The goal of this study was to determine if significant differences in nutrient concentrations and exports exist between Piedmont watersheds with different densities of SSs. Water quality was assessed in watersheds with SSs (n = 11) and a sewer and a forested watershed, which were designated as controls. Stream flow and environmental readings were recorded and water samples were collected from the watersheds from January 2015-December 2016. Additional samples were collected from sand filter watersheds in April 2015-March 2016 to compare to septic and control watersheds. Samples were analyzed for total dissolved nitrogen (TDN) and orthophosphate (PO 4 -P). Results indicated that watersheds served by a high-density (HD) of SSs (4.9 kg-N yr -1 ha -1 ; 0.2 kg-P yr -1 ha -1 ) exported more than double the median masses of TDN and PO 4 -P, respectively, relative to low-density (1.0 kg-N yr -1 ha -1 ; <0.1 kg-P yr -1 ha -1 ) and control watersheds (1.4 kg-N yr -1 ha -1 ; <0.1 kg-P yr -1 ha -1 ) during baseflow. Isotopic analysis indicated that wastewater was the most likely source of nitrate-N in HD watersheds. In all other watersheds, isotopic results suggested non-wastewater sources as the dominant nitrate-N provider. These findings indicated that SS density was a significant factor in the delivery of septic-derived nutrients to these nutrient-sensitive, water supply watersheds of the North Carolina Piedmont. Copyright © 2018 Elsevier Ltd. All rights reserved.

77 FR 48967 - Marine Mammals; File No. 17350

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-15

... permit has been issued to the North Slope Borough Department of Wildlife Management, P.O. Box 69, Barrow, AK 99723 [Taqulik Hepa, Responsible Party; Dr. John C. George, Principal Investigator] to collect...

Reliability of new poly (lactic-co-glycolic acid) membranes treated with oxygen plasma plus silicon dioxide layers for pre-prosthetic guided bone regeneration processes.

PubMed

Castillo-Dalí, G; Castillo-Oyagüe, R; Batista-Cruzado, A; López-Santos, C; Rodríguez-González-Elipe, A; Saffar, J-L; Lynch, C-D; Gutiérrez-Pérez, J-L; Torres-Lagares, D

2017-03-01

The use of cold plasmas may improve the surface roughness of poly(lactic-co-glycolic) acid (PLGA) membranes, which may stimulate the adhesion of osteogenic mediators and cells, thus accelerating the biodegradation of the barriers. Moreover, the incorporation of metallic-oxide particles to the surface of these membranes may enhance their osteoinductive capacity. Therefore, the aim of this paper was to evaluate the reliability of a new PLGA membrane after being treated with oxygen plasma (PO2) plus silicon dioxide (SiO2) layers for guided bone regeneration (GBR) processes. Circumferential bone defects (diameter: 11 mm; depth: 3 mm) were created on the top of eight experimentation rabbits' skulls and were randomly covered with: (1) PLGA membranes (control), or (2) PLGA/PO2/SiO2 barriers. The animals were euthanized two months afterwards. A micromorphologic study was then performed using ROI (region of interest) colour analysis. Percentage of new bone formation, length of mineralised bone, concentration of osteoclasts, and intensity of ostheosynthetic activity were assessed and compared with those of the original bone tissue. The Kruskal-Wallis test was applied for between-group com Asignificance level of a=0.05 was considered. The PLGA/PO2/SiO2 membranes achieved the significantly highest new bone formation, length of mineralised bone, concentration of osteoclasts, and ostheosynthetic activity. The percentage of regenerated bone supplied by the new membranes was similar to that of the original bone tissue. Unlike what happened in the control group, PLGA/PO2/SiO2 membranes predominantly showed bone layers in advanced stages of formation. The addition of SiO2 layers to PLGA membranes pre-treated with PO2 improves their bone-regeneration potential. Although further research is necessary to corroborate these conclusions in humans, this could be a promising strategy to rebuild the bone architecture prior to rehabilitate edentulous areas.

Palm-based medium-and-long-chain triacylglycerol (P-MLCT): production via enzymatic interesterification and optimization using response surface methodology (RSM).

PubMed

Lee, Yee-Ying; Tang, Teck-Kim; Phuah, Eng-Tong; Karim, Nur Azwani Ab; Alwi, Siti Maslina Mohd; Lai, Oi-Ming

2015-02-01

Structured lipid such as medium-and long-chain triacylglycerol (MLCT) is claimed to be able to suppress body fat accumulation and be used to manage obesity. Response surface methodology (RSM) with four factors and three levels (+1,0,-1) faced centered composite design (FCCD) was employed for optimization of the enzymatic interesterification conditions of palm-based MLCT (P-MLCT) production. The effect of the four variables namely: substrate ratio palm kernel oil: palm oil, PKO:PO (40:60-100:0 w/w), temperature (50-70 °C), reaction time (0.5-7.5 h) and enzyme load (5-15 % w/w) on the P-MLCT yield (%) and by products (%) produced were investigated. The responses were determined via acylglycerol composition obtained from high performance liquid chromatography. Well-fitted models were successfully established for both responses: P-MLCT yield (R (2) = 0.9979) and by-products (R (2) = 0.9892). The P-MLCT yield was significantly (P < 0.05) affected by substrate ratio, reaction time and reaction temperature but not enzyme load (P > 0.05). Substrate ratio PKO: PO (100:0 w/w) gave the highest yield of P-MLCT (61 %). Nonetheless, substrate ratio of PKO: PO (90:10w/w) was chosen to improve the fatty acid composition of the P-MLCT. The optimized conditions for substrate ratio PKO: PO (90:10 w/w) was 7.26 h, 50 °C and 5 % (w/w) Lipozyme TLIM lipase, which managed to give 60 % yields of P-MLCT. Up scaled results in stirred tank batch reactor gave similar yields as lab scale. A 20 % increase in P-MLCT yield was obtained via RSM. The effect of enzymatic interesterification on the physicochemical properties of PKO:PO (90:10 w/w) were also studied. Thermoprofile showed that the P-MLCT oil melted below body temperature of 37 °C.

Acquisition of a Surface Plasmon Resonance Imager, Digital Microscope, and Peristaltic Pumps for Defense-Based Research

DTIC Science & Technology

2016-05-05

SECURITY CLASSIFICATION OF: The goal of this proposal is to purchase the GWC Technologies, Inc. Horizontal Surface Plasmon Resonance Imaging (SPRi...Unlimited UU UU UU UU 05-05-2016 1-Feb-2014 31-Jan-2016 Final Report: Acquisition of a Surface Plasmon Resonance Imager, Digital Microscope, and...S) AND ADDRESS (ES) U.S. Army Research Office P.O. Box 12211 Research Triangle Park, NC 27709-2211 Surface Plasmon Resonance Imager, Digital

Pharmacokinetics of flunixin meglumine in mature swine after intravenous, intramuscular and oral administration

PubMed Central

2013-01-01

Background The purpose of this study was to determine intravenous (IV), intramuscular (IM) and oral (PO) FM PK in mature swine. Appropriate pain management for lameness in swine is a critical control point for veterinarians and producers, but science-based guidance on optimal housing, management and treatment of lameness is deficient. Six mature swine (121–168 kg) were administered an IV, IM, or PO dose of flunixin meglumine at a target dose of 2.2 mg/kg in a cross-over design with a 10 day washout period between treatments. Plasma samples collected up to 48 hours post-administration were analyzed by high pressure liquid chromatography and mass spectrometry (HPLC-MS) followed by non-compartmental pharmacokinetic analysis. Results No adverse effects were observed with flunixin meglumine administration for all routes. Flunixin meglumine was administered at an actual mean dose of 2.21 mg/kg (range: 2.05-2.48 mg/kg) IV, IM and PO. A mean peak plasma concentration (CMAX) for IM and PO administration was 3748 ng/ml (range: 2749–6004 ng/ml) and 946 ng/ml (range: 554–1593 ng/ml), respectively. TMAX was recorded at 1.00 hour (range: 0.50-2.00 hours) and 0.61 hours (range: 0.17-2.00 hours) after PO and IM administration. Half-life (T ½ λz) for IV, IM and PO administration was 6.29 hours (range: 4.84-8.34 hours), 7.49 hours (range: 5.55-12.98 hours) and 7.08 hours (range: 5.29-9.15 hours) respectively. In comparison, bioavailability (F) for PO administration was 22% (range: 11-44%) compared to IM F at 76% (range: 54-92%). Conclusions The results of the present study suggest that FM oral administration is not the most effective administration route for mature swine when compared to IV and IM. Lower F and Cmax of PO-FM in comparison to IM-FM suggest that PO-FM is less likely to be an effective therapeutic administration route. PMID:23941181

Influence of laboratory degradation methods and bonding application parameters on microTBS of self-etch adhesives to dentin.

PubMed

Erhardt, Maria Carolina G; Pisani-Proença, Jatyr; Osorio, Estrella; Aguilera, Fátima S; Toledano, Manuel; Osorio, Raquel

2011-04-01

To evaluate the laboratory resistance to degradation and the use of different bonding treatments on resin-dentin bonds formed with three self-etching adhesive systems. Flat, mid-coronal dentin surfaces from extracted human molars were bonded according to manufacturer's directions and submitted to two challenging regimens: (A) chemical degradation with 10% NaOC1 immersion for 5 hours; and (B) fatigue loading at 90 N using 50,000 cycles at 3.0 Hz. Additional dentin surfaces were bonded following four different bonding application protocols: (1) according to manufacturer's directions; (2) acid-etched with 36% phosphoric acid (H3PO4) for 15 seconds; (3) 10% sodium hypochlorite (NaOClaq) treated for 2 minutes, after H3PO4-etching; and (4) doubling the application time of the adhesives. Two one-step self-etch adhesives (an acetone-based: Futurabond/FUT and an ethanol-based: Futurabond NR/FNR) and a two-step self-etch primer system (Clearfil SE Bond/CSE) were examined. Specimens were sectioned into beams and tested for microtensile bond strength (microTBS). Selected debonded specimens were observed under scanning electron microscopy (SEM). Data (MPa) were analyzed by ANOVA and multiple comparisons tests (alpha= 0.05). microTBS significantly decreased after chemical and mechanical challenges (P< 0.05). CSE showed higher microTBS than the other adhesive systems, regardless the bonding protocol. FUT attained the highest microTBS after doubling the application time. H3PO4 and H3PO4 + NaOCl pretreatments significantly decreased bonding efficacy of the adhesives.

Healthy Adult Male Facial Skin Surface Lipid Pheromone p.o. to Treat Opioid Addiction

ClinicalTrials.gov

2018-03-20

Opioid Addiction; Opioid Abuse, Continuous Use; Opioid Use; Opioid-Related Disorders; Paternal Pheromone Deficiency; Opioid Dependence; Opioid Abuse; Opioid-use Disorder; Opioid Intoxication; Opioid Abuse, Episodic

30 CFR 901.10 - State regulatory program approval.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Commission, 1811 Second Avenue, 2nd Floor, P.O. Box 2390, Jasper, AL 35502. (b) Office of Surface Mining Reclamation and Enforcement, Birmingham Field Office, Barber Business Park, 135 Gemini Circle, Homewood, AL...

30 CFR 901.10 - State regulatory program approval.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Commission, 1811 Second Avenue, 2nd Floor, P.O. Box 2390, Jasper, AL 35502. (b) Office of Surface Mining Reclamation and Enforcement, Birmingham Field Office, Barber Business Park, 135 Gemini Circle, Homewood, AL...

30 CFR 901.10 - State regulatory program approval.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Commission, 1811 Second Avenue, 2nd Floor, P.O. Box 2390, Jasper, AL 35502. (b) Office of Surface Mining Reclamation and Enforcement, Birmingham Field Office, Barber Business Park, 135 Gemini Circle, Homewood, AL...

30 CFR 901.10 - State regulatory program approval.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Commission, 1811 Second Avenue, 2nd Floor, P.O. Box 2390, Jasper, AL 35502. (b) Office of Surface Mining Reclamation and Enforcement, Birmingham Field Office, Barber Business Park, 135 Gemini Circle, Homewood, AL...

30 CFR 901.10 - State regulatory program approval.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Commission, 1811 Second Avenue, 2nd Floor, P.O. Box 2390, Jasper, AL 35502. (b) Office of Surface Mining Reclamation and Enforcement, Birmingham Field Office, Barber Business Park, 135 Gemini Circle, Homewood, AL...

Aspects on the analysis of 210Po.

PubMed

Henricsson, F; Ranebo, Y; Holm, E; Roos, P

2011-05-01

There has been little development regarding analysis of polonium (Po) in environmental samples since the 1960 ies. This is due to the straightforward spontaneous deposition of this element on silver (Ag), nickel (Ni) or copper (Cu) without any radiochemical separation. For many years, no radiochemical yield determinant was used and it was generally supposed that the yield was 100% after two depositions. Counting was often done using ZnS scintillation counter coupled to a photomultiplier tube. However, the use of the yield determinants (208)Po and (209)Po and the development of alpha spectrometry showed that the yield was lower. Furthermore, the tendency of Po to volatilize at low temperatures constrains the sample preparation techniques; dry-ashing cannot be used. But during the wet-ashing procedure, there are still some losses. The aim of this study was to evaluate the Po losses during wet-ashing by the use of a double-tracer technique. We have found that the losses were about 30% when open glass beakers were used and about 17% when the samples were digested in microwave oven. When long-necked bottles (Kjeldahl flasks) were used, a loss of about 20% was registered. It has also been observed that (210)Pb to some extent is plating out together with its daughter nuclide Po during the electrochemical deposition. This will result in a systematic error since an unknown amount of supported (210)Po will be produced from the (210)Pb decay depending on the fraction of (210)Pb being deposited on the disc and the waiting time between deposition and measurement of the sample. A further consequence of this is that in the assessment of the (210)Pb content in the sample, very often the remaining liquid is stored after deposition for build-up of (210)Po. Since some (210)Pb is lost on the disc, the result for (210)Pb will be too low. Both these systematic errors give rise to a too high (210)Po/(210)Pb ratio. The fraction of (210)Pb which is plating out has been assessed in this study for different matrices and is about 50-90%. During the measurement by solid state Si-detectors, some Po is evaporated in the vacuum conditions contaminating the detectors. Experiments have here been done by heating the discs after deposition which indicate that less Po is evaporated from Ag than from Ni. The losses from Ag are less than that from the other metals probably due to a deeper penetration into the surface of Po. We conclude that in most aspects, Ag is better to use than the other plating metals. Copyright © 2010 Elsevier Ltd. All rights reserved.

Impact of optical feedback on current-induced polarization behavior of 1550 nm vertical-cavity surface-emitting lasers.

PubMed

Deng, Tao; Wu, Zheng-Mao; Xie, Yi-Yuan; Wu, Jia-Gui; Tang, Xi; Fan, Li; Panajotov, Krassimir; Xia, Guang-Qiong

2013-06-01

Polarization switching (PS) between two orthogonal linearly polarized fundamental modes is experimentally observed in commercial free-running 1550 nm vertical-cavity surface-emitting lasers (VCSELs) (Raycan). The characteristics of this PS are strongly modified after introducing a polarization-preserved (PP) or polarization-orthogonal (PO) optical feedback. Under the case that the external cavity is approximately 30 cm, the PP optical feedback results in the PS point shifting toward a lower injection current, and the region within which the two polarization modes coexist is enlarged with the increase of the PP feedback strength. Under too-strong PP feedback levels, the PS disappears. The impact of PO optical feedback on VCSEL polarization behavior is quite similar to that of PP optical feedback, but larger feedback strength is needed to obtain similar results.

The relationship between cadmium and phosphate in the Atlantic Ocean unravelled

NASA Astrophysics Data System (ADS)

Middag, Rob; van Heuven, Steven M. A. C.; Bruland, Kenneth W.; de Baar, Hein J. W.

2018-06-01

Cadmium (Cd) is not generally considered a nutrient element, but behaves like a nutrient in the oceans and might play an important role in ocean biology after all. The relationship between Cd and the nutrient phosphate (PO4) has been studied for over 40 yrs, but the debate on the driving mechanism and reason behind the 'kink', a change in the steepness of the slope is ongoing. Using new data of high accuracy and spatial resolution covering the West-Atlantic Ocean from north to south, in combination with a robust extended optimum multiparameter (eOMP) water mass model, we show that mixing between different water masses is the dominant factor explaining the observed correlation and its kink. Regeneration of Cd via remineralisation explains the smaller scale variability, notably in the surface ocean. Observations imply the availability of Cd in surface waters determines the Cd-uptake and thus the Cd:PO4 remineralisation ratio. This ratio is variable between different ocean regions, notably between the northern and southern high latitude oceans. Due to their role in deep water formation, both the northern and southern high latitude oceans are a driving factor in the Atlantic and global Cd and PO4 relation. Outside the Atlantic Ocean, the classical kink is not expected, but the relationship is by no means linear. Most likely, this is due to the interaction between low latitude surface waters and subsurface waters from high latitude origin, but more data are required to assess this in detail.

Fabrication and characterization of mesoporous activated carbon from Lemna minor using one-step H3PO4 activation for Pb(II) removal

NASA Astrophysics Data System (ADS)

Huang, Yang; Li, Shunxing; Lin, Haibin; Chen, Jianhua

2014-10-01

A low cost and locally available material, Lemna minor, was used to fabricate activated carbon using H3PO4 activation. After H3PO4 activation, the L. minor activated carbons (LACs) possess high mesoporosity (92.2%) and a surface area of 531.9 m2/g according to Brunauer-Emmett-Teller (BET) analysis. Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectrometer (XPS) analyses reveal the presence of rich hydroxyl, carboxyl, amide and phosphate functional groups on the LACs surface, leading to facile Pb(II) binding to the surface through strong chemisorptive bonds or ion-exchange. The kinetic and equilibrium data were well described by pseudo-first-order model and Langmuir isotherm, with the maximum monolayer adsorption capacity (qm) 170.9 mg/g at 25 °C. The intra-particle diffusion mechanism was partially responsible for the adsorption. The adsorption process was spontaneous and endothermic with negative ΔG and positive ΔH. The Pb(II)-loaded LACs could be easily regenerated using 0.1-M HCl and reused for seven cycles without significant adsorption capacity reduction. The maximum percentage removal rate for Pb(II) (20 mg/L) was found to be 91.8% within 30 min, at optimum conditions of pH 6.0 and 25 °C. These suggested that the low-cost LACs could be used as a potential adsorbent in the treatment of lead-contaminated water.

Noninvasive, near infrared spectroscopic-measured muscle pH and PO2 indicate tissue perfusion for cardiac surgical patients undergoing cardiopulmonary bypass

NASA Technical Reports Server (NTRS)

Soller, Babs R.; Idwasi, Patrick O.; Balaguer, Jorge; Levin, Steven; Simsir, Sinan A.; Vander Salm, Thomas J.; Collette, Helen; Heard, Stephen O.

2003-01-01

OBJECTIVE: To determine whether near infrared spectroscopic measurement of tissue pH and Po2 has sufficient accuracy to assess variation in tissue perfusion resulting from changes in blood pressure and metabolic demand during cardiopulmonary bypass. DESIGN: Prospective clinical study. SETTING: Academic medical center. SUBJECTS: Eighteen elective cardiac surgical patients. INTERVENTION: Cardiac surgery under cardiopulmonary bypass. MEASUREMENTS AND MAIN RESULTS: A near infrared spectroscopic fiber optic probe was placed over the hypothenar eminence. Reference Po2 and pH sensors were inserted in the abductor digiti minimi (V). Data were collected every 30 secs during surgery and for 6 hrs following cardiopulmonary bypass. Calibration equations developed from one third of the data were used with the remaining data to investigate sensitivity of the near infrared spectroscopic measurement to physiologic changes resulting from cardiopulmonary bypass. Near infrared spectroscopic and reference pH and Po2 measurements were compared for each subject using standard error of prediction. Near infrared spectroscopic pH and Po2 at baseline were compared with values during cardiopulmonary bypass just before rewarming commenced (hypotensive, hypothermic), after rewarming (hypotensive, normothermic) just before discontinuation of cardiopulmonary bypass, and at 6 hrs following cardiopulmonary bypass (normotensive, normothermic) using mixed-model analysis of variance. Near infrared spectroscopic pH and Po2 were well correlated with the invasive measurement of pH (R2 =.84) and Po2 (R 2 =.66) with an average standard error of prediction of 0.022 +/- 0.008 pH units and 6 +/- 3 mm Hg, respectively. The average difference between the invasive and near infrared spectroscopic measurement was near zero for both the pH and Po2 measurements. Near infrared spectroscopic Po2 significantly decreased 50% on initiation of cardiopulmonary bypass and remained depressed throughout the bypass and monitored intensive care period. Near infrared spectroscopic pH decreased significantly during cardiopulmonary bypass, decreased significantly during rewarming, and remained depressed 6 hrs after cardiopulmonary bypass. Diabetic patients responded differently than nondiabetic subjects to cardiopulmonary bypass, with lower muscle pH values (p =.02). CONCLUSIONS: Near infrared spectroscopic-measured muscle pH and Po2 are sensitive to changes in tissue perfusion during cardiopulmonary bypass.

Examination of the Behavior of Bismuth in Shallow-Level Hydrothermal Ore Systems: Constraints Based on Hydrothermal Experiments at 800°C and 100 MPa

NASA Astrophysics Data System (ADS)

Wilmot, M. S.; Candela, P. A.; Piccoli, P. M.; Simon, A. C.; McDonough, W. F.

2006-05-01

The partitioning of ore metals between melt and crystals affects the concentrations of these metals in an evolving ore fluid, and therefore the efficiency of their removal from the magma by hydrothermal processes. Some porphyry-type W-Mo deposits contain recoverable amounts of Bi, whereas others contain only trace amounts. In order to determine the magmatic controls on the ratio of Bi to other commodities in these and other deposits, we examined the partitioning behavior of bismuth between melt, minerals and aqueous phases. Hydrothermal experiments were performed by using externally heated cold seal vessels and employing a double capsule technique. Experiments contained 40 mg of Bishop Tuff glass (SiO2 = 74% ) and 40 mg of either magnetite or pyrrhotite. Bi was added as elemental Bi (< 1 mg). Two different aqueous solutions were used. Initially, the added aqueous phase comprised the solutes HCl, KCl and NaCl in a molar1:1:1 ratio, with a bulk salinity of 10 wt % NaCl eq. The aqueous phase for later experiments contained only the solutes KCl and NaCl in a 1:1 molar ratio. Pre-fractured quartz was added to the experiments to trap fluid inclusions at run PTX conditions. Experiments were performed in Au or Pt capsules held inside Rene 41 cold-seal vessels at 800°C and 100 MPa for durations of up to 36 hours. Analytical data have been collected from the run product solids by using an electron probe microanalyzer (major and trace elements) and laser ablation inductively coupled plasma mass spectrometry (trace elements). Bi in Mt is found in concentrations up to 100 ppm, with higher concentrations in runs where Po decomposed to form magnetite. The Bi concentration in the glass ranges up to 100 ppm. In the Po-bearing runs, data were only collected from Po grains in the experiments containing the HCl-free aqueous solution (the Po grains in the other experiments were too small to analyze). Pyrrhotite contained 10-20 ppm Bi, whereas the glass contained 5-10 ppm. Preliminary Nernst- type partition coefficients for Bi between Mt and melt and Po and melt are approximately 5 and 2, respectively. These data reveal that Bi is only slightly compatible in Mt and Po, and that the Po/melt partition coefficient for Bi is much lower than for Cu, Ag and Au, and is comparable to Mn and Zn. Additional experiments are in progress to more compare the partitioning of Bi with that of W and Mo.

Polonium-210 and Caesium-137 in lynx (Lynx lynx), wolverine (Gulo gulo) and wolves (Canis lupus).

PubMed

Gjelsvik, Runhild; Holm, Elis; Kålås, John Atle; Persson, Bertil; Asbrink, Jessica

2014-12-01

Wolves, lynx and wolverines are on the top of the food-chain in northern Scandinavia and Finland. (210)Po and (137)Cs have been analysed in samples of liver, kidney and muscle from 28 wolves from Sweden. In addition blood samples were taken from 27 wolves. In 9 of the wolves, samples of muscle, liver and blood were analysed for (210)Po. Samples of liver and muscle were collected from 16 lynx and 16 wolverines from Norway. The liver samples were analysed for (210)Po and (137)Cs. Only (137)Cs analyses were carried out for the muscle samples. The wolves were collected during the winter 2010 and 2011, while the samples for lynx and wolverines were all from 2011. The activity concentrations of (210)Po in wolves were higher for liver (range 20-523 Bq kg(-1) d.w.) and kidney (range 24-942 Bq kg(-1) d.w.) than muscle (range 1-43 Bq kg(-1) d.w.) and blood (range 2-54 Bq kg(-1) d.w.). Activity ratios, (210)Po/(210)Pb, in wolf samples of muscle, liver and blood were in the ranges 2-77, 9-56 and 2-54. Using a wet weight ratio of 3.8 the maximal absorbed dose from (210)Po to wolf liver was estimated to 3500 μGy per year. Compared to wolf, the ranges of (210)Po in liver samples were lower in lynx (range 22-211 Bq kg(-1) d.w.) and wolverine (range16-160 Bq kg(-1) d.w.). Concentration of (137)Cs in wolf samples of muscle, liver, kidney and blood were in the ranges 70-8410 Bq kg(-1) d.w., 36-4050 Bq kg(-1) d.w., 31-3453 Bq kg(-1) d.w. and 4-959 Bq kg(-1) d.w., respectively. (137)Cs in lynx muscle and liver samples were in the ranges 44-13393 Bq kg(-1) d.w. and 125-10260 Bq kg(-1) d.w. The corresponding values for (137)Cs in wolverine were 22-3405 Bq kg(-1) d.w. for liver and 53-4780 Bq kg(-1) d.w. for muscle. The maximal absorbed dose from (137)Cs to lynx was estimated to 3000 μGy per year. Copyright © 2014 Elsevier Ltd. All rights reserved.

Understanding the fate of sanitation-related nutrients in a shallow sandy aquifer below an urban slum area.

PubMed

Nyenje, P M; Havik, J C N; Foppen, J W; Muwanga, A; Kulabako, R

2014-08-01

We hypothesized that wastewater leaching from on-site sanitation systems to alluvial aquifers underlying informal settlements (or slums) may end up contributing to high nutrient loads to surface water upon groundwater exfiltration. Hence, we conducted a hydro-geochemical study in a shallow sandy aquifer in Bwaise III parish, an urban slum area in Kampala, Uganda, to assess the geochemical processes controlling the transport and fate of dissolved nutrients (NO3, NH4 and PO4) released from on-site sanitation systems to groundwater. Groundwater was collected from 26 observation wells. The samples were analyzed for major ions (Ca, Mg, Na, Mg, Fe, Mn, Cl and SO4) and nutrients (o-PO4, NO3 and NH4). Data was also collected on soil characteristics, aquifer conductivity and hydraulic heads. Geochemical modeling using PHREEQC was used to determine the level of o-PO4 control by mineral solubility and sorption. Groundwater below the slum area was anoxic and had near neutral pH values, high values of EC (average of 1619μS/cm) and high concentrations of Cl (3.2mmol/L), HCO3 (11mmol/L) and nutrients indicating the influence from wastewater leachates especially from pit latrines. Nutrients were predominantly present as NH4 (1-3mmol/L; average of 2.23mmol/L). The concentrations of NO3 and o-PO4 were, however, low: average of 0.2mmol/L and 6μmol/L respectively. We observed a contaminant plume along the direction of groundwater flow (NE-SW) characterized by decreasing values of EC and Cl, and distinct redox zones. The redox zones transited from NO3-reducing in upper flow areas to Fe-reducing in the lower flow areas. Consequently, the concentrations of NO3 decreased downgradient of the flow path due to denitrification. Ammonium leached directly into the alluvial aquifer was also partially removed because the measured concentrations were less than the potential input from pit latrines (3.2mmol/L). We attributed this removal (about 30%) to anaerobic ammonium oxidation (anammox) given that the cation exchange capacity of the aquifer was low (<6meq/100g) to effectively adsorb NH4. Phosphate transport was, on the other hand, greatly retarded and our results showed that this was due to the adsorption of P to calcite and the co-precipitation of P with calcite and rhodochrosite. Our findings suggest that shallow alluvial sandy aquifers underlying urban slum areas are an important sink of excessive nutrients leaching from on-site sanitation systems. Copyright © 2014 Elsevier B.V. All rights reserved.

A cost-minimization analysis in minimally invasive spine surgery using a national cost scale method.

PubMed

Maillard, Nicolas; Buffenoir-Billet, Kevin; Hamel, Olivier; Lefranc, Benoit; Sellal, Olivier; Surer, Nathalie; Bord, Eric; Grimandi, Gael; Clouet, Johann

2015-03-01

The last decade has seen the emergence of minimally invasive spine surgery. However, there is still no consensus on whether percutaneous osteosynthesis (PO) or open surgery (OS) is more cost-effective in treatment of traumatic fractures and degenerative lesions. The objective of this study is to compare the clinical results and hospitalization costs of OS and PO for degenerative lesions and thoraco-lumbar fractures. This cost-minimization study was performed in patients undergoing OS or PO on a 36-month period. Patient data, surgical and clinical results, as well as cost data were collected and analyzed. The financial costs were calculated based on diagnosis related group reimbursement and the French national cost scale, enabling the evaluation of charges for each hospital stay. 46 patients were included in this cost analysis, 24 patients underwent OS and 22 underwent PO. No significant difference was found between surgical groups in terms of patient's clinical features and outcomes during the patient hospitalization. The use of PO was significantly associated with a decrease in Length Of Stay (LOS). The cost-minimization revealed that PO is associated with decreased hospital charges and shorten LOS for patients, with similar clinical outcomes and medical device cost to OS. This medico-economic study has leaded to choose preferentially the use of minimally invasive surgery techniques. This study also illustrates the discrepancy between the national health system reimbursement and real hospital charges. The medico-economic is becoming critical in the current context of sustainable health resource allocation. Copyright © 2015 Surgical Associates Ltd. Published by Elsevier Ltd. All rights reserved.

3D Quaternary deformation pattern in the central Po Plain (Northern Italy)

NASA Astrophysics Data System (ADS)

Sileo, G.; Mueller, K.; Michetti, A. M.; Livio, F.; Berlusconi, A.; Carcano, C.; Rogledi, S.; Vittori, E.

2009-04-01

The Po Plain is a foredeep basin flanked by the two major and active orogens of the Italian Peninsula, the Alps to the North and the Apennines to the South. The basin has a quasi - triangular shape and grades longitudinally to the East in the Adriatic Sea. We used petroleum industry seismic reflection data acquired by ENI E&P in the Central Po Plain, over an area spanning about 6800 km2 from Lake Como to the W to Lake Garda to the E, and from the Lombardian Southern Alps to the N and the Emilia Apennines to the S, in order to analyze and interpret selected seismic reflectors and to define the evolution in space and time of the local active tectonic structures. Folds associated with underlying thrusts were recognized based on deformation recorded by two regional sequence boundary horizons, i.e. the ‘A' Surface (1.6 Myr) and the ‘R' Surface (0. 9 Myr; e.g., Carcano & Piccin, 2002; Muttoni et al., 2003), characterized by good stratigraphic and age bracketing, and marking significant changes in the sedimentary architecture of the Po Basin. Age controls are based on stratigraphic, paleontological and magnetostratigraphic analysis by ENI E&P and Regione Lombardia (Carcano & Piccin, 2002; Scardia et al., 2006). The analysis of strain recorded by these horizons allowed us to: A) recognize a belt of active fold and thrust structures, each 10 to 20 km long, arranged with an en-echelon pattern across the whole Po Basin, and B) analyze their evolution over the Quaternary. 'A' surface (1.6 Myr) The ‘A' surface has been mapped over about 7800 Km2. From North to South four major morphobathymetric domains can be defined in the Pleistocene marine Po Basin: an Alpine platform domain, a slope that links it with the wider central basin domain, a smaller and steeper slope and an Apennine platform domain. The basin shape has an asymmetric transversal profile and is ca. 40 km wide. Several tectonic structures affect this surface. On the Alpine platform domain two small structures have been identified. We interpreted them as N-verging fault propagation folds with low angle ramps that detach the Gonfolite Lombarda clastics (Oligo - Miocene; Bernoulli et al., 1989; Gelati et al., 1991) from the underlying Upper Cretaceous carbonates. The present-day geomorphic evidence of these two structures are represented by the Pievedizio, Capriano, Castenedolo and Ciliverghe Hills South of Brescia (Livio et al, 2008; Michetti et al., 2008). On the basin floor domain nine structures have been identified. Six of them belong to the Southern Alps and we interpreted them as S-verging fault propagation folds. All these structures have a double plunging termination (Burbank & Anderson, 2001) that mark the endpoints of actively slipping blind thrusts. These structures range from 11 to 16 km long with an average strike of N 110° E. The remaining three structures record shortening at the leading edge of the Apennines; their axial lengths range from 8 to 28 km and the average axial strike is 110°. These structures thus define the 3D architecture of blind thrusts hidden beneath the basin floor; these collectively define the two active, facing fronts of the Apennines and Southern Alps thrust belts (Fantoni et al. 2004). ‘R' Surface The second analyzed surface is the ‘R' surface (0.9 Myr.); strain measured across this sequence stratigraphic boundary confirmed and further defines the magnitude and timing of shortening accommodated by fault propagation folds described on the ‘A' surface. Differences between the basin between "A" and "R" surface time include the arrangement of the structures on the basin floor and by the number of the identified structures. The Alpine platform domain in "R" time is in fact more extended than on the ‘A' surface, and a less steep slope links it with a wider but less deep basin domain; the Apennines platform is smaller, because it has been involved in the deformation of the more internal Apennines structures. The basin floor is ca. 30 km wide with a progressive westward narrowing, and still displays an asymmetric transversal profile. Sedimentation rates are considerably higher than uplift rates of the structures, resulting in a paleobathymetry gentler than the ‘A' surface The measurement of the folds axial length becomes consequently more difficult. In order to filter the tectonic signal we conducted a profile curvature analysis perpendicular to the mean axial direction of the structures. We recognized six structures with an average length of 18 - 20 km and an average axial strike of N 110° E. The comparison of these structures with those recognized on the ‘A' surface clearly shows a decreasing number of folds, suggesting some thrusts shut off between "A" and "R" surface time. The similar geometry of folded "R" and "A" surfaces suggest consistent fault geometry and stress orientation during this time. This kinematic pattern is consistent with a spatially - varying shortening rate model (e.g., Salvini & Storti, 2002). The folds appear to grow with constant fault geometry and the displacement varies along strike since the tip of the faults migrates laterally in a direction perpendicular to the regional horizontal stress (Mueller & Talling, 1997, Keller et al., 1999; Champel et al, 2002; Burbank & Anderson, 2001). In summary, the analysis of the two described Quaternary seismic surfaces allowed us to understand the evolution of active folds within the Po Plain and their growth mechanism and evolution both in space and time. These folds are the modern loci of compressive strain that links the Southern Alps with the Northern Apennines. Comparing the two surfaces we can observe a significant shift in the localization of the tectonic deformation, consisting A) in the reactivation of N-verging backthrusts and associated folds in the Southern Alps instead of the main forethrusts, and B) in a similar backward skip of the activity from the outermost Apennines fronts, with the reactivation of the Pedeappenninic Thrust Fault (e.g. Boccaletti & Martelli, 2004). This might be related to a differential sedimentary load between proximal and distal portions of the basin related to increased erosion, especially in the Alps in hinterland areas and corresponding sedimentation in the foreland, both triggered by climate change in the Mid-Pleistocene (e.g. Muttoni et al., 2002). REFERENCES Boccaletti, M. & Martelli, L., (Editors) (2004) - Carta Sismotettonica della Regione Emilia-Romagna: Note Illustrative. Regione Emilia-Romagna, Servizio Geologico, Sismico e dei Suoli CNR - Firenze, SELCA S.r.l., Firenze, 60 p. Burbank, D., Anderson, R. (2001) - Tectonic Geomorphology. Wiley Blackwell. ISBN: 978-0-632-04386-6 Carcano, C. & Piccin, A. (Editors) (2002) - Geologia Degli Acquiferi Padani Della Regione Lombardia. Firenze: S.El.Ca. Champel, B., Van Der Beek, P., Mugnier J.& Leturmy, P. (2002) - Growth And Lateral Propagation Of Fault-Related Folds In The Siwaliks Of Western Nepal: Rates, Mechanisms, And Geomorphic Signature. Journal Of Geophysical Research, 107, B6, doi 10.1029/2001jb000578. Desio, A. (1965) - I Rilievi Isolati Della Pianura Lombarda Ed I Movimenti Tettonici Del Quaternario. Rend. Ist. Lom. Acc. Sc. Lett., Sez. A 99 pp.881-894. Fantoni, R., Bersezio, R., & Forcella, F., (2004) - Alpine structure and deformation chronology at the Southern Alps-Po Plain border in Lombardy. Boll. Soc. Geol. It., 123, 3, p. 463- 476. Keller, E. A., Gurrola, L. & Tierney, T. E. (1999) - Geomorphic Criteria To Determine Direction Of Lateral Propagation Of Reverse Faulting And Folding. Geology (Boulder), 27, 6, p. 515-518. Livio F., Berlusconi A., Michetti A.M., Sileo G., Zerboni A., Cremaschi M., Trombino L., Carcano C., Rogledi S., Vittori E., Mueller K. (2008) - Fagliazione Superficiale Olocenica E Paleoliquefazione Nel Sito Di Monte Netto, Brescia: Implicazioni Sismotettoniche. Rend. Online Sgi, 1, Note Brevi, www.Socgeol.It, p. 101-103. Michetti A.M., Berlusconi A., Livio F., Sileo G., Zerboni A., Cremaschi M., Trombino L, Mueller K., Vittori E., Carcano C., Rogledi S. (2008) - Holocene Surface Faulting At Monte Netto, Brescia, And The Christmas 1222 (Io = Ix Mcs) Earthquake In The Po Plain, Italy: What Does It Mean "Blind Fault"? Geophysical Research Abstracts, 10, Egu2008-A-00000, 2008 Egu General Assembly 2008. Mueller, K. & Talling, P. (1997) - Geomorphic Evidence For Tear Faults Accommodating Lateral Propagation Of An Active Fault-Bend Fold, Wheeler Ridge, California. Journal Of Structural Geology, 19, 3-4, p. 397-411. Muttoni G., Carcano, C., Garzanti, E., Ghielmi, M., Piccin, A., Pini, R., Rogledi, S., Sciunnach, D. (2002) - Onset Of Major Pleistocene Galciations In The Alps. Geology. - 2003. - 11 : 31. - p. 989-992. Salvini, F. & Storti, F. (2002) - Three-Dimensional Architecture Of Growth Strata Associated To Fault-Bend, Fault-Propagation, And Decollement Anticlines In Non-Erosional Environments. Sedimentary Geology, 146, p 57 - 73 Scardia, G., Muttoni, G. & Sciunnach, D. (2006) - Subsurface Magnetostratigraphy Of Pleistocene Sediments From The Po Plain (Italy): Constraints On Rates Of Sedimentation And Rock Uplift. GSA Bulletin 118, 11/12, p.1299-1312.

Explaining the Paleoproterozoic Rise of O2

NASA Astrophysics Data System (ADS)

Anbar, A. D.; Rye, R.; Kaufman, A. J.

2001-12-01

The Paleoproterozoic rise of atmospheric O2 is not understood. Geochemical evidence indicates pO2 \\leq 5 x 10-4 atm before ~ 2.2 Ga and >= 0.03 atm by 2.0 Ga [1]. Most models of this rapid oxygenation account for the timing in an ad hoc manner. In contrast, we suggest oxygenation was driven by rising solar luminosity, a hypothesis consistent with emerging geochemical evidence. Solar luminosity was { ~} 80 % of present value 2.75 Ga. Climate models indicate that pCO2 > 0.2 atm was required before 2.75 Ga if CO2 alone accounted for greenhouse enhancement that averted global glaciation [2]. Paleosols reveal pCO2 <= 10-1.4 atm between 2.75 and 2.2 Ga [3]. This constraint may extend earlier [4]. Given insufficient CO2, CH4 likely helped maintain surface temperature. pCH4 > 10-4 atm would have been adequate 2.75 Ga; Methanogens could sustain this level as long as pO2 was negligible [5]. Atmospheric CH4 and O2 are incompatible. If CH4 was a critical greenhouse gas, increases in pO2 caused global cooling. Temperature and photosynthetic O2 production are probably positively correlated between 273 and 300 K. Combined, these effects constituted a negative feedback on pO2: Excess O2 production cooled the surface, decreasing O2 production until pCH4 was restored. Methanogenesis was decoupled from this feedback as the bulk of Archean methanogens presumably lived in the deep ocean, insulated from surface temperature. Hence, the CH4 greenhouse acted as a cap on pO2 in the Archean. This cap would have eased as rising solar luminosity permitted "titration" of CH4 by increased O2 production; pO2 increased slowly as pCH4 decreased. This feedback suppressed pO2 until solar luminosity allowed the CO2-H2O greenhouse to maintain equable temperatures without appreciable CH4. This threshold was crossed { ~} 2.5 to 2.0 Ga [2], explaining Paleoproterozoic oxygenation. As Earth approached the threshold the CH4 buffer shrank and the likelihood of the feedback being temporarily overwhelmed by sudden O2 blooms increased. This hypothesis is consistent with observations of extreme climatic instability between 2.5 and 2.0 Ga, including evidence of at least two, possibly three, episodes of global glaciation 2.4 to 2.2 Ga [6]. We predict that Paleoproterozoic glacial episodes should be preceded by increased oxygen production- excess O2 production is predicted to cause pCH4 erosion and cooling. 13C-enriched carbonates underlying the glaciogenic Timeball Hill Fm, S. Africa [6] indicate enhanced carbon burial associated with such O2 production. Significantly, there is no evidence of glaciation following the largest Paleoproterozoic 13C excursion,{ ~} 2.2 Ga; solar luminosity at this time was sufficient to avoid glaciation despite pCH4 << 10-4 atm. Greenhouse considerations no longer limited the rise of pO2 after this time, consistent with paleosol and other evidence of oxygenation. Further study of 13C in Paleoproterozoic and late Archean carbonates are critical to test and extend this hypothesis. 1. Rye & Holland (1998), Am. J. Sci. 298, 621; 2. Kasting (1987), Precamb. Res. 34, 205; 3. Rye et al. (1995) Nature 378, 603; 4. Sleep & Zahnle (2001) JGR 106, 1373; 5. Pavlov et al. (2000) JGR 105, 11981; 6. Bekker et al. (2001), Am. J. Sci. 301, 601.

National Dam Safety Program. Clove Lake Dam (NJ 00259) Delaware River Basin, Shimers Brook, Sussex County, New Jersey. Phase I Inspection Report.

DTIC Science & Technology

1981-08-01

1 AU9r, 1,981 Division of Water Resources ~ .N~EtO P.O. Box CN029 I.NME Trenton, NJ 08625 50 R.MONITORING AGENCY NAME 0 ADORESS(ll dilloai how Cmnt...trespassing on the slopes of the dam. j. Provide a drain or other means for removing water collecting in the low-level outlet chamber. k. Reestablish and...Copies furnished: Mr. Dirk C. Hofman, P.E., Deputy Director Division of Water Resources N.J. Dept. of Environmental IProtection P.O. Box CN029 Trenton

Polonium-210 in marine mussels (bivalve molluscs) inhabiting the southern coast of India.

PubMed

Khan, M Feroz; Wesley, S Godwin; Rajan, M P

2014-12-01

The present study focused on the determination of the alpha-emitter, (210)Po, in two species of marine mussels (bivalve molluscs) commonly available in the southern coastal region of India. The brown mussel, Perna indica was collected from the west coast and the green mussel, Perna viridis from the east coast. The concentration of (210)Po was related to the allometry (length of shell, wet/dry weight of shell/soft tissue) of the mussels and significant results were found. The study period focused on three seasons namely, pre-monsoon, monsoon and post-monsoon for a 1-year period (2010-2011). The results revealed higher activity levels in smaller-sized mussels compared to larger ones. Marked variation in (210)Po activity concentration was noted in the whole-body soft tissues between seasons and sampling site (p < 0.05). The dose rate assessment for mussels was performed using the ERICA Assessment tool. The chronic exposure to mussels due to (210)Po was found to be lesser than the global benchmark dose rate of 10 μGy h(-1). The effective ingestion dose to adults who intake mussels was estimated to be in the range 5.1-34.9 μSv y(-1). The measurement contributes to the furthering of knowledge of (210)Po, since no data exist in this region. Copyright © 2014 Elsevier Ltd. All rights reserved.

H3PO4 solution hydrothermal carbonization combined with KOH activation to prepare argy wormwood-based porous carbon for high-performance supercapacitors

NASA Astrophysics Data System (ADS)

Dai, Changchao; Wan, Jiafeng; Yang, Juan; Qu, Shanshan; Jin, Tieyu; Ma, Fangwei; Shao, Jinqiu

2018-06-01

In this work, argy wormwood-based porous carbon electrode materials for high-performance supercapacitors are prepared through H3PO4 solution hydrothermal carbonization and subsequent KOH activation. The obtained carbon has a specific surface area (SSA) of 927 m2 g-1, a total pore volume of 0.56 cm3 g-1, and a high oxygen (9.38%) content. In three-electrode system, it exhibits specific capacitance of 344 F g-1 at 1 A g-1. Moreover, the symmetric supercapacitor shows an excellent rate capability of 87% retention from 1 A g-1 to 10 A g-1, and a good cycling performance with 91.6% retention over 5000 cycles in 6 M KOH. Therefore, the sample activated by H3PO4 & KOH exhibits an excellent future in energy storage.

Atmospheric Oxygen Concentrations for the Past 350 Myr Modeled from the δ13C of C3 Land Plants

NASA Astrophysics Data System (ADS)

Nordt, L.; Breecker, D.

2016-12-01

Numerous studies have focused on the systematic collection of long-term d13C records from marine sediments, but no such isotopic compilation exists for C3 land plants. Consequently, we gathered a meta-data base of 8003 plant-derived δ13C values (ISOORG) from various carbon sources binned into 5 myr time steps. The results of this investigation were reported in a recent publication showing that most δ13C sources co-vary with ten CIEs during the last 400 myr. For this paper we culled ISOORG to produce ISOORG16-H that contains 7025 plant-derived δ13C values from paleo-moist environments to reflect secular controls on the δ13C of C3 plants. We then constructed atmospheric pO2 curves for the past 350 myr using prior experimental work showing a direct relationship between the Δ13C of C3 plants and pO2 concentration. Periods of hyperoxia (25-30% pO2) were identified from 300-250, 225-190, and 110-105 myr, and intervals of hypoxia (10-15% pO2) from 350-345, 245-230, and 185-115 myr. During the last 150 myr, pO2 stabilized at 17-24% except for a notable positive excursion from 110-105 myr. Hyperoxia, apparently from widespread carbon burial, supports the notion of insect gigantism during the Late Paleozoic. Hypoxia during the early Triassic correlates with the coal gap following the collapse of Paleozoic ecosystems. Rising pO2 in the late Triassic seems to reflect renewed carbon burial from reorganization of Mesozoic ecosystems. The middle Mesozoic is characterized by low pO2 during an intense greenhouse interval, with ambient conditions ensuing thereafter possibly linked to carbon burial from the radiation of angiosperms. pO2 concentrations >14% suggest wildfires persisted through the study interval except possibly at 160 and 140 myr. Intervals of low pO2 concentration were likely accompanied by lower atmospheric pressure and higher temperatures, particularly from 245-230 myr and 180-120 myr. Our O2 reconstructions conform with GEOCARBSULF, but not with proxy predictions from charcoal abundance or the δ13C of amber where the former overestimates and the latter underestimates pO2, respectively, compared to GEOCARBSULF. Results of our new proxy are encouraging, but further experimental work is needed to better understand the dynamics of pO2 and pCO2 on the Δ13C of C3 plants for application to paleobarometers.

Evaluation of the possibility of using the water of the Bystrytsya-Nadvirnyans'ka River in Cherniiv (Ukraine) to supply the population with drinking water

NASA Astrophysics Data System (ADS)

Pietrzak, D.; Mandryk, O.; Wątor, K.; Kmiecik, E.; Zelmanowych, A.

2018-02-01

The article presents the results of the research carried out in order to assess the possibility of using surface water of the Bystrytsya-Nadvirnyans'ka River in Cherniiv (western Ukraine), for the public supply of water intended for human consumption. For this purpose an existing database that contains the results of analyses of surface water samples collected in 1999, 2002, 2005, 2008, 2011 and 2014 was used. Each year, from 8 to 13 samples were collected from the Bystrytsya-Nadvirnyans'ka River in Cherniiv. Physicochemical analyses of the samples taken included the determination of pH value, temperature, TDS, alkalinity, hardness, dissolved oxygen, BOD5, COD, suspended solids and ions: Ca2+, Mg2+, Na+, K+, Fe2+, NH4+, Cu2+, Cl-, SO42-, PO43-, HCO3-, NO2-, NO3-. These chemical analyses were verified by calculation of errors based on the ionic balance. The results of the analyses were referred to the polish applicable requirements for surface water used for public supply of water intended for human consumption and to the regulation regarding the classification of the surface water status and environmental quality standards for priority substances. The results indicate that water of the Bystrytsya-Nadvirnyans'ka River in the area of Cherniiv was out of the class in the years 1999 and 2002 due to exceeding the limit values for category A3 for Cu2+. On the basis of incomplete assessment of the status of the Bystrytsya-Nadvirnyans'ka River water (due to the tests limitation to the physical and chemical components) determined that the water has a bad status because it exceeded the limits for class II for Cl-, SO42-, NO3- and TDS. In the samples collected in 1999 and 2002 it is also observed exceeding the maximum limit concentrations for Cu2+.

Deep Eutectic Solvent Synthesis of LiMnPO4/C Nanorods as a Cathode Material for Lithium Ion Batteries

PubMed Central

Wu, Zhi; Huang, Rong-Rong; Yu, Hang; Xie, Yong-Chun; Lv, Xiao-Yan; Su, Jing; Long, Yun-Fei; Wen, Yan-Xuan

2017-01-01

Olivine-type LiMnPO4/C nanorods were successfully synthesized in a chloride/ethylene glycol-based deep eutectic solvent (DES) at 130 °C for 4 h under atmospheric pressure. As-synthesized samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) and electrochemical tests. The prepared LiMnPO4/C nanorods were coated with a thin carbon layer (approximately 3 nm thick) on the surface and had a length of 100–150 nm and a diameter of 40–55 nm. The prepared rod-like LiMnPO4/C delivered a discharge capacity of 128 mAh·g−1 with a capacity retention ratio of approximately 93% after 100 cycles at 1 C. Even at 5 C, it still had a discharge capacity of 106 mAh·g−1, thus exhibiting good rate performance and cycle stability. These results demonstrate that the chloride/ethylene glycol-based deep eutectic solvents (DES) can act as a new crystal-face inhibitor to adjust the oriented growth and morphology of LiMnPO4. Furthermore, deep eutectic solvents provide a new approach in which to control the size and morphology of the particles, which has a wide application in the synthesis of electrode materials with special morphology. PMID:28772493

The mechanism of improved aeration due to gas films on leaves of submerged rice.

PubMed

Verboven, Pieter; Pedersen, Ole; Ho, Quang Tri; Nicolai, Bart M; Colmer, Timothy D

2014-10-01

Some terrestrial wetland plants, such as rice, have super-hydrophobic leaf surfaces which retain a gas film when submerged. O2 movement through the diffusive boundary layer (DBL) of floodwater, gas film and stomata into leaf mesophyll was explored by means of a reaction-diffusion model that was solved in a three-dimensional leaf anatomy model. The anatomy and dark respiration of leaves of rice (Oryza sativa L.) were measured and used to compute O2 fluxes and partial pressure of O2 (pO2 ) in the DBL, gas film and leaf when submerged. The effects of floodwater pO2 , DBL thickness, cuticle permeability, presence of gas film and stomatal opening were explored. Under O2 -limiting conditions of the bulk water (pO2  < 10 kPa), the gas film significantly increases the O2 flux into submerged leaves regardless of whether stomata are fully or partly open. With a gas film, tissue pO2 substantially increases, even for the slightest stomatal opening, but not when stomata are completely closed. The effect of gas films increases with decreasing cuticle permeability. O2 flux and tissue pO2 decrease with increasing DBL thickness. The present modelling analysis provides a mechanistic understanding of how leaf gas films facilitate O2 entry into submerged plants. © 2014 John Wiley & Sons Ltd.

Carbon nanostructures modified LiFePO4 cathodes for lithium ion battery applications: optimized porosity and composition

NASA Astrophysics Data System (ADS)

Mahmoud, Lama; Singh Lalia, Boor; Hashaikeh, Raed

2016-12-01

Lithium iron phosphate (LiFePO4) battery cathode was fabricated without using any metallic current collector and polymeric binder. Carbon nanostructures (CNS) were used as microbinders for LiFePO4 particles and at the same time as a 3D current collector. A facile and cost effective method of fabricating composite cathodes of CNS and LiFePO4 was developed. Thick electrodes with high loading of active material (20-25 mg cm-2) were obtained that are almost 2-3 folds higher than commercial electrodes. SEM images confirm that the 3D CNS conductive network encapsulated the LiFePO4 particles homogenously facilitating the charge transfer at the electrode-CNS interface. The composition, scan rate and porosity of the paper-like cathode were sequentially varied and their influence was systematically monitored by means of linear sweep cyclic voltammetry and AC electrochemical impedance spectroscopy. Addition of CNS improved the electrode’s bulk electronic conductivity, mechanical integrity, surface area and double layer capacitance, yet compromised the charge transfer resistance at the electrode-electrolyte interface. Based on a range of the tested binder-free electrodes, this study proposes that electrodes with 20 wt% CNS having 49 ± 2.5% porosity had realized best improvements of two folds and four folds in the electronic conductivity and diffusion coefficient, respectively.

Arctigenin, a phenylpropanoid dibenzylbutyrolactone lignan, inhibits type I-IV allergic inflammation and pro-inflammatory enzymes.

PubMed

Lee, Ji Yun; Kim, Chang Jong

2010-06-01

We previously reported that arctigenin, a phenylpropanoid dibenzylbutyrolactone lignan isolated from Forsythia koreana, exhibits anti-inflammatory, antioxidant, and analgesic effects in animal models. In addition, arctigenin inhibited eosinophil peroxidase and activated myeloperoxidase in inflamed tissues. In this study, we tested the effects of arctigenin on type I-IV allergic inflammation and pro-inflammatory enzymes in vitro and in vivo. Arctigenin significantly inhibited the heterologous passive cutaneous anaphylaxis induced by ovalbumin in mice at 15 mg/kg, p.o., and compound 48/80-induced histamine release from rat peritoneal mast cells at 10 microM. Arctigenin (15 mg/kg, p.o.) significantly inhibited reversed cutaneous anaphylaxis. Further, arctigenin (15 mg/kg, p.o.) significantly inhibited the Arthus reaction to sheep's red blood cells, decreasing the hemolysis titer, the hemagglutination titer, and the plaque-forming cell number for SRBCs. In addition, arctigenin significantly inhibited delayed type hypersensitivity at 15 mg/kg, p.o. and the formation of rosette-forming cells at 45 mg/kg, p.o. Contact dermatitis induced by picrylchloride and dinitrofluorobenzene was significantly (p < 0.05) inhibited by surface treatment with arctigenin (0.3 mg/ear). Furthermore, arctigenin dose-dependently inhibited pro-inflammatory enzymes, such as cyclooxygenase-1 and 2, 5-lipoxygenase, phospholipase A2, and phosphodiesterase. Our results show that arctigenin significantly inhibited B- and T-cell mediated allergic inflammation as well as pro-inflammatory enzymes.

Synthesis of sodium lauryl sulphate (SLS)-modified activated carbon from risk husk for waste lead (Pb) removal

NASA Astrophysics Data System (ADS)

Al-Latief, D. N.; Arnelli, Astuti, Y.

2015-12-01

Surfactant-modified active carbon (SMAC) has been successfully synthesized from waste rice husk using a series of treatments i.e. carbonization, activation with H3PO4 and surface modification using sodium lauryl sulfate (SLS). The synthesized SMAC was characterized using SEM-EDX and FTIR. The adsorption results show that the SMAC synthesized using H3PO4 treatment for 8 hours followed with SLS treatment for 5 hours had efficiency and capacity of the waste lead removal of 99.965% and 0.499825 mg.g-1, respectively.

Radon emanation from the moon - Spatial and temporal variability.

NASA Technical Reports Server (NTRS)

Gorenstein, P.; Golub, L.; Bjorkholm, P.

1973-01-01

Observations of Rn-222 and Po-210 on the lunar surface with the orbiting Apollo alpha particle spectrometer reveal a number of features in their spatial distribution and indicate the existence of time variations in lunar radon emission. Localized Rn-222 or Po-210 around the craters Aristarchus and Grimaldi and the edges of virtually all maria indicates time varying radon emission and suggests a correlation between alpha 'hot spots' and sites of transient optical events observed from the earth. In a gross sense, the slower variations of Rn-222 seem to correlate with the distribution of gamma activity.

Hidden Surface Removal through Object Space Decomposition.

DTIC Science & Technology

1982-01-01

12 2.1 Methods of Subdividing the Object Space ..................................................... 14 2.2 Accessing...AC.AIIA TO5ASK FORCE MNT OF TECH WRIONT-PATTERSON AFB 0O4 P/O 1a/I 64100(6 SURFACE REMOVAL THROWN4 OBJECT SPACE 0(COMPOSIT109d.(U UiCLASIFIEC AFZITNl...Surface Removal Through Object Space THESlS/ J AJ;I Decomposition 6. PERFORMING ORG. REPORT NUMBER 7. AUTHOR() a. CONTRACT OR GRANT NUMBER(s) Robert

The Theory and Practice of Bayesian Image Labeling

DTIC Science & Technology

1988-08-01

simple. The intensity images are the results of many confounding factors - lighting, surface geometry , surface reflectance, and camera characteristics...related through the geometry of the surfaces in view. They are conditionally independent in the following sense: P (g,O Ifp) = P (g Ifl) P(O If,). (6.6a...different spatial resolution and projection geometry , or using DOG-type filters of various scales. We believe that the success of visual integration at

Effect of oxygen partial pressure on oxidation of Mo-metal

NASA Astrophysics Data System (ADS)

Sharma, Rabindar Kumar; Kumar, Prabhat; Singh, Megha; Gopal, Pawar; Reddy, G. B.

2018-05-01

This report explains the effect of oxygen partial pressure (PO2 ) on oxidation of Mo-metal in oxygen plasma. XRD results indulge that oxide layers formed on Mo-surfaces at different oxygen partial pressures have two different oxide phases (i.e. orthorhombic MoO3 and monoclinic Mo8O23). Intense XRD peaks at high pressure (i.e. 2.0×10-1 Torr) points out the formation of thick oxide layer on Mo-surface due to presence of large oxygen species in chamber and less oxide volatilization. Whereas, at low PO2 (6.5×10-2 and 7.5×10-2 Torr.) the reduced peak strength is owing to high oxide volatilization rate. SEM micrographs and thickness measurements also support XRD results and confirm that the optimum -2value of PO2 to deposited thicker and uniform oxide film on glass substrate is 7.5×10-2 Torr through plasma assistedoxidation process. Further to study the compositional properties, EDX of the sample M2 (the best sample) is carried out, which confirms that the stoichiometric ratio is less than 3 (i.e. 2.88). Less stoichiometric ratio again confirms the presence of sub oxides in oxide layers on Mo metal as evidenced by XRD results. All the observed results are well in consonance with each other.

Characteristics and short-term changes of the Po Delta seafloor morphology through high-resolution bathymetric and backscatter data

NASA Astrophysics Data System (ADS)

Madricardo, Fantina; Bosman, Alessandro; Kruss, Aleksandra; Remia, Alessandro; Correggiari, Anna; Fogarin, Stefano; Romagnoli, Claudia; Moscon, Giorgia

2016-04-01

River deltas are highly dynamical and valuable environments and often undergo strong natural and human-induced actions that need constant monitoring. Whereas remote sensing observations of the sub-aerial part of the delta are very important for the assessment of the morphological changes over long time scales (years-decades), the short time-scale evolution of the submerged part of the system remains often undetermined. In particular, the shallow-water submarine pro-delta front is commonly characterized by active depositional and erosional processes. This area is crucial for the understanding of the fluvial and coastal dynamics. In this study, we applied geophysical investigations to characterize the very shallow-water area of the Po river delta in the northern Adriatic Sea. The modern Po delta is the result of increased sediment flux derived from both climate change (Little Ice Age) and human impact (deforestation and diversion and construction of artificial levees) and in recent years is suffering erosion. Here, we present the results of two high-resolution multibeam echosounder surveys carried out in June 2013 and in September 2014 on the Po river mouth and delta front in the framework of the Ritmare Project. The Po delta front, as other modern deltas, has a complicated morphology, consisting of multiple terminal distributary channels, subaqueous levee deposits, and mouth bars. The high-resolution bathymetric data show that the prodelta slope has a curved shape with an overall southward asymmetry of the submerged delta due to prevalent longshore currents. The 2013 bathymetric map highlights a number of sedimentary features, such as depositional bars, radiating in the prodelta slope with an asymmetric section, with steeper southward lee side. The new bathymetric map collected in 2014 shows impressive changes: in correspondence with the depositional lobes, we observed extensive collapse depressions with bathymetric changes of over 1 m in 15 months and widespread instability phenomena along the slope. Moreover, the acoustic backscatter intensity data and grab samples collected in the area provided information about the superficial sediment distribution during the two surveys, while the study of the water-column backscatter intensity revealed the presence of gas plume in the water-column. These results contribute to a better understanding the recent sediment dynamics and evolution of the Po Delta system.

Rejection of Erroneous Saturation Data in Optical Pulse Oximetry in Newborn Patients

NASA Astrophysics Data System (ADS)

Scalise, L.; Marchionni, Paolo; Carnielli, Virgilio P.

2011-08-01

Pulse oximetry (PO) is extensively used in intensive care unit (ICU); this is mainly due to the fact that it is a non-invasive and real-time monitoring method. PO allows to measure arterial oxygen saturation (SaO2) and in particular hemoglobin oxygenation. Optical PO is typically realized by the use of a clip (to be applied on the ear or on the finger top) containing a couple of monochromatic LED sources and a photodiode. The main drawback with the use of PO is the presence of movement artifacts or disturbance due to optical sources and skin, causing erroneous saturation data. The aim of this work is to present the measurement procedure based on a specially developed algorithm able to reject erroneous oxygen saturation data during long lasting monitoring of patients in ICU and to compare measurement data with reference data provided by EGA. We have collected SaO2 data from a standard PO and used an intensive care unit monitor to collect data. This device was connected to our acquisition system and heart rate (HR) and SaO2 data were acquired and processed by our specially developed algorithm and directly reproduced on the PC screen for use by the clinicians. The algorithm here used for the individuation and rejection of erroneous saturation data is based on the assessment of the difference between the Heart Rate (HR) measured by respectively by the ECG and PO. We have used an emogasanalyzer (EGA) for comparison of the measured data. The study was carried out in a neonatal intensive care unit (NICU), using 817 data coming from 24 patients and the observation time was of about 10000 hours. Results show a reduction in the maximum difference between the SaO2 data measured, simultaneously, on the same patient by the EGA and by the proposed method of 14.20% and of the 4.76% in average over the 817 samples. The measurement method proposed is therefore able to individuate and eliminate the erroneous saturation data due to motion artifacts and reported by the pulse oxymeter. Specifically in neonatal ICU, it allows to come to more efficient individuation of apnea, hypoxia and hyperoxia events and consequently to operate more adequate and efficient therapeutic actions.

Biotic and abiotic factors affect the nest environment of embryonic leatherback turtles, Dermochelys coriacea.

PubMed

Wallace, Bryan P; Sotherland, Paul R; Spotila, James R; Reina, Richard D; Franks, Bryan F; Paladino, Frank V

2004-01-01

Clutches of leatherback turtles, Dermochelys coriacea, have lower hatching success than those of other sea turtles, but causes of high embryonic mortality are unknown. We measured characteristics of clutches along with spatial and temporal changes in PO(2) and temperature during incubation to determine the extent to which they affected the developmental environment of leatherback embryos. Minimum PO(2) in nests decreased as both the total number and mass of metabolizing embryos increased. Increases in both the number and mass of metabolizing embryos caused an increase in maximum nest temperature. However, neither PO(2) nor temperature was correlated with hatching success. Our measurements of relatively high nest PO(2) (lowest 17.1 kPa or 16.9% O(2)) indicate that hypoxia apparently does not cause the low hatching success of leatherback clutches. Oxygen partial pressure increased and temperature decreased from the center toward the periphery of leatherback nests. We inferred from these measurements that positions of eggs within nests vary in quality and potentially affect overall developmental success of entire clutches. The large metabolic mass of leatherback clutches and limits to gas flux imposed by the sand create a situation in which leatherback embryos collectively affect their own environment.

Influence of porous texture and surface chemistry on the CO₂ adsorption capacity of porous carbons: acidic and basic site interactions.

PubMed

Sánchez-Sánchez, Angela; Suárez-García, Fabián; Martínez-Alonso, Amelia; Tascón, Juan M D

2014-12-10

Doped porous carbons exhibiting highly developed porosity and rich surface chemistry have been prepared and subsequently applied to clarify the influence of both factors on carbon dioxide capture. Nanocasting was selected as synthetic route, in which a polyaramide precursor (3-aminobenzoic acid) was thermally polymerized inside the porosity of an SBA-15 template in the presence of different H3PO4 concentrations. The surface chemistry and the porous texture of the carbons could be easily modulated by varying the H3PO4 concentration and carbonization temperature. Porous texture was found to be the determinant factor on carbon dioxide adsorption at 0 °C, while surface chemistry played an important role at higher adsorption temperatures. We proved that nitrogen functionalities acted as basic sites and oxygen and phosphorus groups as acidic ones toward adsorption of CO2 molecules. Among the nitrogen functional groups, pyrrolic groups exhibited the highest influence, while the positive effect of pyridinic and quaternary functionalities was smaller. Finally, some of these N-doped carbons exhibit CO2 heats of adsorption higher than 42 kJ/mol, which make them excellent candidates for CO2 capture.

Investigation of anodic and chemical oxides grown on p-type InP with applications to surface passivation for n(+)-p solar cell fabrication

NASA Technical Reports Server (NTRS)

Faur, Maria; Faur, Mircea; Goradia, Manju; Goradia, Chandra; Jenkins, Phillip; Jayne, Douglas; Weinberg, Irving

1991-01-01

Most of the previously reported InP anodic oxides were grown on a n-type InP with applications to fabrication of MISFET structures and were described as a mixture of In2O3 and P2O5 stoichiometric compounds or nonstoichiometric phases which have properties similar to crystalline compounds In(OH)3, InPO4, and In(PO3)3. Details of the compositional change of the anodic oxides grown under different anodization conditions were previously reported. The use of P-rich oxides grown either by anodic or chemical oxidation are investigated for surface passivation of p-type InP and as a protective cap during junction formation by closed-ampoule sulfur diffusion. The investigation is based on but not limited to correlations between PL intensity and X-ray photoelectron spectroscopy (XPS) chemical composition data.

Statistical optimization of beta-carotene production by Arthrobacter agilis A17 using response surface methodology and Box-Behnken design

NASA Astrophysics Data System (ADS)

Özdal, Murat; Özdal, Özlem Gür; Gürkök, Sümeyra

2017-04-01

β-carotene is a commercially important natural pigment and has been widely applied in the medicine, pharmaceutical, food, feed and cosmetic industries. The current study aimed to investigate the usability of molasses for β-carotene production by Arthrobacter agilis A17 (KP318146) and to optimize the production process. Box-Behnken Design of Response Surface Methodology was used to determine the optimum levels and the interactions of three independent variables namely molasses, yeast extract and KH2PO4 at three different levels. β-carotene yield in optimized medium containing 70 g/l molasses, 25 g/l yeast extract and 0.96 g/l KH2PO4, reached up to 100 mg/l, which is approximately 2.5-fold higher than the yield, obtained from control cultivation. A remarkable β-carotene production on inexpensive carbon source was achieved with the use of statistical optimization.

Locomotor and Heart Rate Responses of Floaters During Small-Sided Games in Elite Soccer Players: Effect of Pitch Size and Inclusion of Goalkeepers.

PubMed

Lacome, Mathieu; Simpson, Ben M; Cholley, Yannick; Buchheit, Martin

2018-05-01

To (1) compare the locomotor and heart rate responses between floaters and regular players during both small and large small-sided games (SSGs) and (2) examine whether the type of game (ie, game simulation [GS] vs possession game [PO]) affects the magnitude of the difference between floaters and regular players. Data were collected in 41 players belonging to an elite French football team during 3 consecutive seasons (2014-2017). A 5-Hz global positionning system was used to collect all training data, with the Athletic Data Innovation analyzer (v5.4.1.514) used to derive total distance (m), high-speed distance (>14.4 km·h -1 , m), and external mechanical load (MechL, a.u.). All SSGs included exclusively 1 floater and were divided into 2 main categories, according to the participation of goalkeepers (GS) or not (PO) and then further divided into small and large (>100 m 2 per player) SSGs based on the area per player ratio. Locomotor activity and MechL performed were likely-to-most likely lower (moderate to large magnitude) in floaters compared with regular players, whereas differences in heart rate responses were unclear to possibly higher (small) in floaters. The magnitude of the difference in locomotor activity and MechL between floaters and regular players was substantially greater during GS compared with PO. Compared with regular players, floaters present decreased external load (both locomotor and MechL) despite unclear to possibly slightly higher heart rate responses during SSGs. Moreover, the responses of floaters compared with regular players are not consistent across different sizes of SSGs, with greater differences during GS than PO.

Flow and nutrient dynamics in a subterranean estuary (Waquoit Bay, MA, USA): Field data and reactive transport modeling

NASA Astrophysics Data System (ADS)

Spiteri, Claudette; Slomp, Caroline P.; Charette, Matthew A.; Tuncay, Kagan; Meile, Christof

2008-07-01

A two-dimensional (2D) reactive transport model is used to investigate the controls on nutrient ( NO3-, NH4+, PO 4) dynamics in a coastal aquifer. The model couples density-dependent flow to a reaction network which includes oxic degradation of organic matter, denitrification, iron oxide reduction, nitrification, Fe 2+ oxidation and sorption of PO 4 onto iron oxides. Porewater measurements from a well transect at Waquoit Bay, MA, USA indicate the presence of a reducing plume with high Fe 2+, NH4+, DOC (dissolved organic carbon) and PO 4 concentrations overlying a more oxidizing NO3--rich plume. These two plumes travel nearly conservatively until they start to overlap in the intertidal coastal sediments prior to discharge into the bay. In this zone, the aeration of the surface beach sediments drives nitrification and allows the precipitation of iron oxide, which leads to the removal of PO 4 through sorption. Model simulations suggest that removal of NO3- through denitrification is inhibited by the limited overlap between the two freshwater plumes, as well as by the refractory nature of terrestrial DOC. Submarine groundwater discharge is a significant source of NO3- to the bay.

The BiPo-3 detector for the measurement of ultra low natural radioactivities of thin materials

NASA Astrophysics Data System (ADS)

Barabash, A. S.; Basharina-Freshville, A.; Birdsall, E.; Blondel, S.; Blot, S.; Bongrand, M.; Boursette, D.; Brudanin, V.; Busto, J.; Caffrey, A. J.; Calvez, S.; Cascella, M.; Cebrián, S.; Cerna, C.; Cesar, J. P.; Chauveau, E.; Chopra, A.; Dafní, T.; De Capua, S.; Duchesneau, D.; Durand, D.; Egorov, V.; Eurin, G.; Evans, J. J.; Fajt, L.; Filosofov, D.; Flack, R.; Garrido, X.; Gómez, H.; Guillon, B.; Guzowski, P.; Holý, K.; Hodák, R.; Huber, A.; Hugon, C.; Iguaz, F. J.; Irastorza, I. G.; Jeremie, A.; Jullian, S.; Kauer, M.; Klimenko, A.; Kochetov, O.; Konovalov, S. I.; Kovalenko, V.; Lang, K.; Lemière, Y.; Le Noblet, T.; Liptak, Z.; Liu, X. R.; Loaiza, P.; Lutter, G.; Luzón, G.; Macko, M.; Mamedov, F.; Marquet, C.; Mauger, F.; Morgan, B.; Mott, J.; Nemchenok, I.; Nomachi, M.; Nova, F.; Ohsumi, H.; Oliviéro, G.; Ortiz de Solórzano, A.; Pahlka, R. B.; Pater, J.; Perrot, F.; Piquemal, F.; Povinec, P.; Přidal, P.; Ramachers, Y. A.; Remoto, A.; Richards, B.; Riddle, C. L.; Rukhadze, E.; Saakyan, R.; Salazar, R.; Sarazin, X.; Shitov, Yu.; Simard, L.; Šimkovic, F.; Smetana, A.; Smolek, K.; Smolnikov, A.; Söldner-Rembold, S.; Soulé, B.; Štekl, I.; Thomas, J.; Timkin, V.; Torre, S.; Tretyak, Vl. I.; Tretyak, V. I.; Umatov, V. I.; Vilela, C.; Vorobel, V.; Waters, D.; Žukauskas, A.

2017-06-01

The BiPo-3 detector, running at the Canfranc Underground Laboratory (Laboratorio Subterr&aposaneo de Canfranc, LSC, Spain) since 2013, is a low-radioactivity detector dedicated to measuring ultra low natural radionuclide contaminations of 208Tl (232Th chain) and 214Bi (238U chain) in thin materials. The total sensitive surface area of the detector is 3.6 m2. The detector has been developed to measure the radiopurity of the selenium double β-decay source foils of the SuperNEMO experiment. In this paper the design and performance of the detector, and results of the background measurements in 208Tl and 214Bi, are presented, and the validation of the BiPo-3 measurement with a calibrated aluminium foil is discussed. Results of the 208Tl and 214Bi activity measurements of the first enriched 82Se foils of the double β-decay SuperNEMO experiment are reported. The sensitivity of the BiPo-3 detector for the measurement of the SuperNEMO 82Se foils is Script A(208Tl) <2 μBq/kg (90% C.L.) and Script A(214Bi) <140 μBq/kg (90% C.L.) after 6 months of measurement.

76 FR 55880 - Recording Assignments

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-09

... DEPARTMENT OF COMMERCE United States Patent and Trademark Office Recording Assignments ACTION: Proposed collection; comment request. SUMMARY: The United States Patent and Trademark Office (USPTO), as... Information Officer, United States Patent and Trademark Office, P.O. Box 1450, Alexandria, VA 22313-1450...

Scientists: Get Involved in Planetary Science Education and Public Outreach! Here’s How!

NASA Astrophysics Data System (ADS)

Buxner, Sanlyn; Dalton, H.; Shipp, S.; CoBabe-Ammann, E.; Scalice, D.; Bleacher, L.; Wessen, A.

2013-10-01

The Planetary Science Education and Public Outreach (E/PO) Forum is a team of educators, scientists, and outreach professionals funded by NASA’s Science Mission Directorate (SMD) that supports SMD scientists currently involved in E/PO - or interested in becoming involved in E/PO efforts - to find ways to do so through a variety of avenues. There are many current and future opportunities and resources for scientists to become engaged in E/PO. The Forum provides tools for responding to NASA SMD E/PO funding opportunities (webinars and online proposal guides), a one-page Tips and Tricks guide for scientists to engage in education and public outreach, and a sampler of activities organized by thematic topic and NASA’s Big Questions in planetary science. Scientists can also locate resources for interacting with diverse audiences through a number of online clearinghouses, including: NASA Wavelength, a digital collection of peer-reviewed Earth and space science resources for educators of all levels (http://nasawavelength.org); the Year of the Solar System website (http://solarsystem.nasa.gov/yss), a presentation of thematic resources that includes background information, missions, the latest in planetary science news, and educational products, for use in the classroom and out, for teaching about the solar system organized by topic - volcanism, ice, astrobiology, etc.; and EarthSpace (http://www.lpi.usra.edu/earthspace), a community website where faculty can find and share resources and information about teaching Earth and space sciences in the undergraduate classroom, including class materials, news, funding opportunities, and the latest education research. Also recently developed, the NASA SMD Scientist Speaker’s Bureau (http://www.lpi.usra.edu/education/speaker) offers an online portal to connect scientists interested in getting involved in E/PO projects - giving public talks, classroom visits, and virtual connections - with audiences. Learn more about the opportunities to become involved in E/PO and to share your science with students, educators, and the general public at http://smdepo.org.

Speciation of 210Po and 210Pb in air particulates determined by sequential extraction.

PubMed

Al-Masri, M S; Al-Karfan, K; Khalili, H; Hassan, M

2006-01-01

Speciation of (210)Po and (210)Pb in air particulates of two Syrian phosphate sites with different climate conditions has been studied. The sites are the mines and Tartous port at the Mediterranean Sea. Air filters were collected during September 2000 until February 2002 and extracted chemically using different selective fluids in an attempt to identify the different forms of these two radionuclides. The results have shown that the inorganic and insoluble (210)Po and (210)Pb (attached to silica and soluble in mineral acids) portion was found to be high in both sites and reached a maximum value of 94% and 77% in the mine site and Tartous port site, respectively. In addition, only 24% of (210)Pb in air particulates was found to be associated with organic materials probably produced from the incomplete burning of fuel vehicle and similar activities. Moreover, the (210)Po/(210)Pb activity ratio in air particulates was higher than that in all samples at both sites and varied between 3.85 in November 2000 at Tartous port site and 20 in April 2001 at the mine area. These activity ratios were also higher than the natural levels. The (210)Po/(210)Pb activity ratio was also determined in each portion resulting from the selective extraction and found to be higher than that in most samples. The sources of (210)Po excess in these portions are discussed. Soil suspension, which is common in the dry climate dominant in the area, sea water spray and heating of phosphate ores were considered; polonium is more volatile than the lead compounds at even moderate temperature. Furthermore, variations in the chemical forms of (210)Po and (210)Pb during the year were also investigated. However, the results of this study can also be utilized for dose assessment to phosphate industry workers.

The U(VI) speciation influenced by a novel Paenibacillus isolate from Mont Terri Opalinus clay.

PubMed

Lütke, Laura; Moll, Henry; Bachvarova, Velina; Selenska-Pobell, Sonja; Bernhard, Gert

2013-05-21

Bacterial cell walls have a high density of ionizable functional groups available for U(VI) binding, hence have a great potential to affect the speciation of this contaminant in the environment. The studied strain of the genus Paenibacillus is a novel isolate originating from the Mont Terri Opalinus clay formations (Switzerland) which are currently investigated as a potential host rock for future nuclear waste storage. U(VI) binding to the cell surface functional groups was studied by potentiometry combined with time-resolved laser-induced fluorescence spectroscopy (TRLFS). Four bacterial U(VI) surface complexes were identified: R-COO-UO2(+), R-O-PO3-UO2, R-O-PO3H-UO2(+), and (R-O-PO3)2-UO2(2-). The corresponding complex stability constants were calculated to be 5.33 ± 0.08, 8.89 ± 0.04, 12.92 ± 0.05, and 13.62 ± 0.08, respectively. Hence UO2(2+) displays a moderate to strong interaction with the bacterial surface functional groups. In the acidic pH range (pH 3) UO2(2+) binding onto the cell envelope is governed by coordination to hydrogen phosphoryl sites. Upon increasing the pH an increasing coordination of UO2(2+) to carboxylic and deprotonated phosphoryl sites was found. At a pH greater than 7 uranyl hydroxides dominate the speciation. Additionally the bacteria-mediated release of inorganic phosphate in dependence on [U(VI)] at different pH values was studied to assess the influence of phosphate release on U(VI) mobilization.

A comparison of the pharmacokinetic and pharmacodynamic properties of nitroglycerin according to the composition of the administration set: A preliminary study.

PubMed

Kim, Choon Ok; Song, Jeongyun; Min, Ji Young; Park, Su Jung; Lee, Hye Mi; Byon, Hyo-Jin

2018-03-01

There is a risk of drug sorption into an intravenous administration set composed of polyvinyl chloride (PVC), polyurethane (PU), or polyolefin (PO). This has implications on the dose of the active ingredient the patient receives, and thus therapeutic success. This study aimed to determine the plasma concentration of nitroglycerin and the effect of nitroglycerin on patients based on the composition of the administration set. Using a randomized, open-labeled, 3 × 3 crossover method, 9 volunteers were assigned to 3 groups. In period I, nitroglycerin (100 μg/mL) was infused via a PVC- (group A), PU- (group B), or PO-based (group C) administration set. In period II, PU- (group A), PO- (group B), and PVC-based (group C) administration sets were used, and in period III, PO- (group A), PVC- (group B), and PU-based (group C) administration sets were used. The rate of drug administration in all periods was 12 mL/hour for 30 minutes using an infusion pump. Blood samples were collected, and the plasma concentrations of nitroglycerin were analyzed using validated high-performance liquid chromatography coupled with tandem mass spectrometry. Blood pressure was determined using a sphygmomanometer applied to the other upper arm at an interval of 5 minutes. We observed that the mean plasma concentration of nitroglycerin over time when administered using a PO-based tube was higher than that when using a PU- or PVC-based tube. When the percent change of the mean arterial pressure from baseline at each time point was compared among groups, there were statistically significant differences between PU and PO or PVC at most points during nitroglycerin infusion. Our results showed higher nitroglycerin plasma concentration and lower arterial pressure when a PO-based administration set was used than when a PVC- or PU-based administration set was used. PO-based administration sets may be more appropriate for nitroglycerin administration compared to those composed of PVC or PU.

A comparison of the pharmacokinetic and pharmacodynamic properties of nitroglycerin according to the composition of the administration set

PubMed Central

Kim, Choon Ok; Song, Jeongyun; Min, Ji Young; Park, Su Jung; Lee, Hye Mi; Byon, Hyo-Jin

2018-01-01

Abstract Background: There is a risk of drug sorption into an intravenous administration set composed of polyvinyl chloride (PVC), polyurethane (PU), or polyolefin (PO). This has implications on the dose of the active ingredient the patient receives, and thus therapeutic success. This study aimed to determine the plasma concentration of nitroglycerin and the effect of nitroglycerin on patients based on the composition of the administration set. Methods: Using a randomized, open-labeled, 3 × 3 crossover method, 9 volunteers were assigned to 3 groups. In period I, nitroglycerin (100 μg/mL) was infused via a PVC- (group A), PU- (group B), or PO-based (group C) administration set. In period II, PU- (group A), PO- (group B), and PVC-based (group C) administration sets were used, and in period III, PO- (group A), PVC- (group B), and PU-based (group C) administration sets were used. The rate of drug administration in all periods was 12 mL/hour for 30 minutes using an infusion pump. Blood samples were collected, and the plasma concentrations of nitroglycerin were analyzed using validated high-performance liquid chromatography coupled with tandem mass spectrometry. Blood pressure was determined using a sphygmomanometer applied to the other upper arm at an interval of 5 minutes. Results: We observed that the mean plasma concentration of nitroglycerin over time when administered using a PO-based tube was higher than that when using a PU- or PVC-based tube. When the percent change of the mean arterial pressure from baseline at each time point was compared among groups, there were statistically significant differences between PU and PO or PVC at most points during nitroglycerin infusion. Conclusion: Our results showed higher nitroglycerin plasma concentration and lower arterial pressure when a PO-based administration set was used than when a PVC- or PU-based administration set was used. PO-based administration sets may be more appropriate for nitroglycerin administration compared to those composed of PVC or PU. PMID:29489681

Comparison of white spot syndrome virus infection resistance between Exopalaemon carinicauda and Litopenaeus vannamei under different salinity stresses

NASA Astrophysics Data System (ADS)

Ge, Qianqian; Yu, Ge; Sun, Ming; Li, Jitao; Li, Jian

2017-12-01

Exopalaemon carinicauda is one of the important economic shrimp species in China, and can tolerate a wide range of salinities. However, its disease resistance remains to be unclear in comparison with other shrimp species under salinity stress. In this study, the resistance to white spot syndrome virus (WSSV) of E. carinicauda and Litopenaeus vannamei was determined by comparing their hemocyanin (Hc) and phenoloxidase (PO) activities under different salinity stresses. In E. carinicauda, the PO activity and Hc gene transcript abundance showed a coherent pattern of increase and decrease while Hc content showed a slightly decrease with Vibrio anguillarum and WSSV infections. For both E. carinicauda and L. vannamei under salinity stress, the PO activity showed a positive correlation with the salinity while the Hc content and expression level of its gene increased significantly in salinities of 5, 15 and 25 g L-1. The survival rate of E. carinicauda with WSSV infection was higher than that of L. vannamei in the first 24 h under different salinity stresses. Drastic mortality of E.carinicauda and L. vannamei appeared at 48 h and 3 h post-injection, respectively. Furthermore, compared with L. vannamei, E. carinicauda displayed higher PO activity, Hc content and abundance of Hc gene mRNA. The results collectively indicated that Hc and PO have obviously functional connection in resisting pathogens and tolerating salinity stress, and PO activity and Hc gene mRNA abundance may reflect the resistance of shrimp to disease. E. carinicauda has higher level of immune potential than L. vannamei, suggesting its greater capacity in resisting pathogens under salinity stresses.

137Cs and 210Po in Pacific Walrus and Bearded Seal from St. Lawrence Island, Alaska

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamilton, T F; Seagars, D J; Jokela, T

2005-02-02

The activity concentration of Cesium-137 ({sup 137}Cs) and naturally-occurring Polonium-210 ({sup 210}Po) were measured in the muscle tissue, kidney and liver of Pacific walrus (Odobenus rosmarus divergens) and bearded seal (Erignathus barbatus) collected by native hunters from the Bering Sea. The mean {sup 137}Cs concentrations in muscle, liver and kidney of Pacific walrus were 0.07, 0.09 and 0.07 Bq kg{sup -1} (N= 5, wet weight), respectively, and 0.17, 0.10, and 0.17 Bq kg{sup -1} (N=2, wet weight), respectively, in bearded seal. In general, {sup 137}Cs tissue concentrations are significantly lower than those previously reported for mammals from other regions. Bymore » comparison, {sup 210}Po activity concentrations appear to be higher than those reported elsewhere but a larger variation. The mean {sup 210}Po concentration in the muscle tissue, liver and kidney of Pacific walrus (N=5, wet weight) were 28.7, 189, and 174 Bq kg{sup -1}, respectively. This compares with {sup 210}Po concentration values (N=2, wet weight) of 27, 207, and 68 Bq kg{sup -1} measured in the muscle tissue, liver and kidney, of bearded seal, respectively. Estimated bioaccumulation factors--as defined by the radionuclide concentration ratio between the target tissue to that in sea water--were two to three orders of magnitude higher for {sup 210}Po that those of {sup 137}Cs. We conclude from radiological dose estimates that ingestion of {sup 137}Cs in foods derived from walrus and seal will pose no threat to human health. This work has important implications for assessing health risks to Alaskan coastal communities concerned about the dumping of nuclear waste in the Russia Arctic.« less

Chemical characterization of solid polymer electrolyte membrane surfaces in LiFePO4 half-cells

NASA Astrophysics Data System (ADS)

Kyu, Thein; He, Ruixuan; Peng, Fang; Dunn, William E.; Kyu's Group Team, Dr.

High temperature (60 °C) capacity retention of succinonitrile plasticized solid polymer electrolyte membrane (PEM) in a LiFePO4 half-cell was investigated with or without lithium bis(oxalato)borate (LiBOB) modification. Various symmetric cells and half-cells were studied under different thermal and electrochemical conditions. At room temperature cycling, the unmodified PEM in the half-cell appeared stable up to 50 cycles tested. Upon cycling at 60 °C, the capacity decays rapidly and concurrently the cell resistance increased. The chemical compositions of the solid PEM surfaces on both cathode and anode sides were analyzed. New IR bands (including those belonged to amide) were discerned on the unmodified PEM surface of the Li electrode side at 60 °C suggestive of side reaction, but no new bands develop during room temperature cycling. To our astonishment, the side reaction was effectively suppressed upon LiBOB addition (0.4 wt%) into the PEM, contributing to increased high temperature capacity retention at 60°C. Plausible mechanisms of capacity fading and improved cycling performance due to LiBOB modification are discussed.

A Black Phosphate Conversion Coating on Steel Surface Using Antimony(III)-Tartrate as an Additive

NASA Astrophysics Data System (ADS)

Li, Feng; Wang, Guiping

2016-05-01

A novel black phosphate conversion coating was formed on steel surface through a Zn-Mn phosphating bath containing mainly ZnO, H3PO4, Mn(H2PO4)2, and Ca(NO3)2, where antimony(III)-tartrate was used as the blackening agent of phosphatization. The surface morphology and composition of the coating were characterized by scanning electron microscopy, energy dispersion spectroscopy, and x-ray photoelectron spectroscopy. Corrosion resistance of the coating was studied by potentiodynamic polarization curves and electrochemical impedance spectroscopy. The pH value of the solution had significant influence on the formation and corrosion resistance of the coating. The experimental results indicated that the Sb plays a vital role in the blackening of phosphate conversion coating. The optimal concentration of antimony(III)-tartrate in the phosphating bath used in this experiment was 1.0 g L-1, as higher values reduced the corrosion resistance of the coating. In addition, by saponification and oil seals, the corrosion duration of the black phosphate coating in a copper sulfate spot test can be as long as 20 min.

Evaluation of Adsorbed Arsenic and Potential Contribution to Shallow Groundwater in Tulare Lake Bed Area, Tulare Basin, California

USGS Publications Warehouse

Gao, S.; Fujii, R.; Chalmers, A.T.; Tanji, K.K.

2004-01-01

Elevated As concentrations in shallow groundwater in parts of the Tulare Basin, California, are a concern because of potential migration into deeper aquifers that could serve as a source of future drinking water. The objectives of this study were to evaluate adsorbed As and the potential contribution to groundwater using (i) isotopic dilution, (ii) successive extraction with an electrolyte solution resembling the pore-water chemical composition, and (iii) PO4 exchange for As. Sediment samples collected from 2 to 4 m below land surface in the Tulare Lake bed area contained a total As concentration of 24 mg As kg-1. Pore water extracted under hydraulic pressure contained a total As concentration of 590 ??g As L-1, which predominantly contained As as arsenate [As(V), 97%], a minor amount of arsenite [As(III), 3%], and non-detectable organic As. The isotopic dilution method [73As(V)] estimated that the concentration of adsorbed As(V) on the sediment was 5.7 mg As kg-1 at pH 8.5 and 6.7 mg As kg-1 at pH 7.5, respectively. Fourteen successive 24-h extractions with the artificial pore water released up to 57 to 61% of the adsorbed As(V) that was determined by isotopic dilution, indicating that only a portion of the adsorbed As could be released to groundwater. The phosphate-exchangeable As (0.1 M PO4, pH 8.5 or 7.5) was 63% of the isotopically exchangeable As(V). Thus, extraction of As by 0.1 M PO4 at ambient pHs is recommended as a method to determine the potential amount of As(V) on sediments that could be released to the solution phase. The overall results indicated that adsorbed As could be a significant source of As to groundwater. However, other factors that affect As transport such as the leaching rate need to be considered.

210Po/210Pb dynamics in relation to zooplankton biomass and trophic conditions during an annual cycle in northwestern Mediterranean coastal waters.

PubMed

Färber Lorda, Jaime; Fowler, Scott W; Miquel, Juan-Carlos; Rodriguez y Baena, Alessia; Jeffree, Ross A

2013-01-01

Monthly sampling in northwestern Mediterranean coastal waters was undertaken to better understand the relationship between zooplankton biomass and the cycling of the natural radionuclide (210)Po/(210)Pb pair during a one-year period (October 1995-November 1996). In conjunction with mesozooplankton collections and (210)Po/(210)Pb measurements in seawater, zooplankton and their fecal pellets, the biochemical composition of particulate organic matter (POM) was also examined at three depths (0, 20 and 50 m) as an indicator of trophic conditions. During May 1996, a strong zooplankton "bloom" was observed which was preceded by a prolonged increase in POM (protein + carbohydrates + lipids) starting at the end of March, and further demonstrated by a concomitant increase in the concentration of smaller particles, two features that are typical of mesotrophic waters. Simultaneous measurements of (210)Po in sea water and zooplankton showed an inverse trend between these two parameters during the sampling period, with the two lowest (210)Po concentrations in the dissolved phase of seawater coincident with the highest radionuclide concentrations in the zooplankton; however, this apparent relationship was not statistically significant over the entire year. Freshly excreted mesozooplankton and salp fecal pellets, which have been strongly implicated in the removal and downward transport of these radionuclides from the upper water column, contained (210)Po and (210)Pb levels ranging from 175 to 878 and 7.5-486 Bq kg(-1) dry weight, respectively. Salp pellets contained 5 and 10 times more (210)Po and (210)Pb than in fecal pellets produced by mixed zooplankton, a finding most likely related to their different feeding strategies. During the zooplankton biomass peak observed in May, the (210)Po concentration in zooplankton was at a minimum; however, in contrast to what has been reported to occur in some open sea oligotrophic waters, over the year no statistically significant inverse relationship was found between zooplankton biomass and (210)Po concentration in zooplankton. This observation may have resulted from the general lack of very low biomass concentrations (<1 mg m(-3)) measured in these coastal waters, biomass levels which commonly occur in open ocean oligotrophic regions. Copyright © 2012 Elsevier Ltd. All rights reserved.

Molecular cloning, expression pattern, and 3D structural prediction of the cold inducible RNA-binding protein (CIRP) in Japanese flounder ( Paralichthys olivaceus)

NASA Astrophysics Data System (ADS)

Yang, Xiao; Gao, Jinning; Ma, Liman; Li, Zan; Wang, Wenji; Wang, Zhongkai; Yu, Haiyang; Qi, Jie; Wang, Xubo; Wang, Zhigang; Zhang, Quanqi

2015-02-01

Cold-inducible RNA-binding protein (CIRP) is a kind of RNA binding proteins that plays important roles in many physiological processes. The CIRP has been widely studied in mammals and amphibians since it was first cloned from mammals. On the contrary, there are little reports in teleosts. In this study, the Po CIRP gene of the Japanese flounder was cloned and sequenced. The genomic sequence consists of seven exons and six introns. The putative PoCIRP protein of flounder was 198 amino acid residues long containing the RNA recognition motif (RRM). Phylogenetic analysis showed that the flounder PoCIRP is highly conserved with other teleost CIRPs. The 5' flanking sequence was cloned by genome walking and many transcription factor binding sites were identified. There is a CpGs region located in promoter and exon I region and the methylation state is low. Quantitative real-time PCR analysis uncovered that Po CIRP gene was widely expressed in adult tissues with the highest expression level in the ovary. The mRNA of the Po CIRP was maternally deposited and the expression level of the gene was regulated up during the gastrula and neurula stages. In order to gain the information how the protein interacts with mRNA, we performed the modeling of the 3D structure of the flounder PoCIRP. The results showed a cleft existing the surface of the molecular. Taken together, the results indicate that the CIRP is a multifunctional molecular in teleosts and the findings about the structure provide valuable information for understanding the basis of this protein's function.

LaPO4:Eu fluorescent nanorods, synthesis, characterization and spectroscopic studies on interaction with human serum albumin

NASA Astrophysics Data System (ADS)

Guo, Xingjia; Yao, Jie; Liu, Xuehui; Wang, Hongyan; Zhang, Lizhi; Xu, Liping; Hao, Aijun

2018-06-01

Eu3+ doped LaPO4 fluorescent nanorods (LaPO4:Eu) was successfully fabricated by a hydrothermal process. The obtained LaPO4:Eu nanorods under the optimal conditions were characterized by means of transmission electron microscopy (TEM), X-ray diffraction (XRD) technique, Fourier transform infrared (FTIR), UV-vis absorption and fluorescence spectroscopy. The nanorods with a length of 50-100 nm and a diameter of about 10 nm, can emit strong red fluorescence upon excitation at 241 nm. The FTIR result confirmed that there are lots of phosphate groups on the surfaces of nanorods. In order to better understand the physiological behavior of nanorods in human body, multiple spectroscopic methods were used to study the interaction between the LaPO4:Eu nanorods and human serum albumin (HSA) in the simulated physiological conditions. The results indicated that the nanorods can effectively quench the intrinsic fluorescence of HSA through a dynamic quenching mode with the association constants of the order of 103 L mol-1. The values of the thermodynamic parameters suggested that the binding of the nanorods to HSA was a spontaneous process and van der Waals forces and hydrogen bonds played a predominant role. The displacement experiments verified that the binding site of nanorods on HSA was mainly located in the hydrophobic pocket of subdomain IIA (site I) of HSA. The binding distance between nanorods and HSA was calculated to be 4.2 nm according to the theory of Förster non-radiation energy transfer. The analysis of synchronous fluorescence, three-dimensional fluorescence (3D) and circular dichroism (CD) spectra indicated that there the addition of LaPO4:Eu nanorods did not caused significant alterations in conformation of HSA secondary structure and the polarity around the amino acid residues.

Trace elements in winter snow of the Dolomites (Italy): a statistical study of natural and anthropogenic contributions.

PubMed

Gabrielli, P; Cozzi, G; Torcini, S; Cescon, P; Barbante, C

2008-08-01

Knowledge of the occurrence of trace elements deposited in fresh alpine snow is very limited. Although current sources of major ionic inorganic species have been well established, this is not the case for many trace elements. This manuscript attempts to reconstruct the origin of Ag, Ba, Bi, Cd, Co, Cr, Cu, Fe, Mo, Mn, Pb, Sb, Ti, U, V and Zn in winter surface snow, extensively collected in the Dolomites region (Eastern Alps, Italy). Sampling of surface snow was conducted weekly during the winter 1998 at 21 sites at altitudes ranging from approximately 1000 to approximately 3000 m. This led to a remarkable dataset of trace element concentrations in surface snow from low latitudes. Here we show a preliminary statistical investigation conducted on the 366 samples collected. It was found that V, Sb, Zn, Cd, Mo and Pb have a predominantly anthropogenic origin, linked to the road traffic in the alpine valleys and the nearby heavily industrialised area of the Po Valley. In addition, the occasionally strong Fe and Cr input may reflect the mechanical abrasion of ferrous components of the vehicles. However, much of the Fe along with Mn, U and Ti originates primarily from the geological background of the Dolomites. A marine contribution was found to be negligible for all the trace elements. The origin of other trace elements is less clear: Ag can be possibly attributed to a predominantly anthropogenic origin while Cr, Co, Cu and Ba are usually from crustal rocks but different than the Dolomites.

Cool Astronomy: Education and Public Outreach for the WISE mission

NASA Astrophysics Data System (ADS)

Mendez, Bryan J.

2011-01-01

The Education and Public Outreach (E/PO) program of the Wide-field Infrared Survey Explorer (WISE) aims to educate and engage students, teachers, and the general public in the endeavor of science. We bring a collection of accomplished professionals in formal and informal astronomy education from around the nation to create learning materials and experiences that appeal to broad audiences. Our E/PO program trains teachers in science, technology, engineering, and mathematics (STEM) topics related to WISE; creates standards-based classroom resources and lessons using WISE data and WISE-related STEM topics; develops interactive programming for museums and science centers; and inspires the public with WISE science and images.

Supervised chaos genetic algorithm based state of charge determination for LiFePO4 batteries in electric vehicles

NASA Astrophysics Data System (ADS)

Shen, Yanqing

2018-04-01

LiFePO4 battery is developed rapidly in electric vehicle, whose safety and functional capabilities are influenced greatly by the evaluation of available cell capacity. Added with adaptive switch mechanism, this paper advances a supervised chaos genetic algorithm based state of charge determination method, where a combined state space model is employed to simulate battery dynamics. The method is validated by the experiment data collected from battery test system. Results indicate that the supervised chaos genetic algorithm based state of charge determination method shows great performance with less computation complexity and is little influenced by the unknown initial cell state.

Highly Permeable AlPO-18 Membranes for N 2 /CH 4 Separation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zong, Zhaowang; Elsaidi, Sameh K.; Thallapally, Praveen K.

Herein we demonstrate that AlPO-18 membranes can separate N2/CH4 gas mixtures at unprecedented N2 permeances. The best membranes separated N2/CH4 mixtures with N2 permeances as high as 3076 GPU and separation selectivities as high as 4.6. Gas mixture separation data, N2 and CH4 adsorption isotherms, ideal adsorbed solution theory (IAST), and breakthrough experiments were collected to understand the separation mechanisms. Competitive adsorption and differences in diffusivities were identified as the prevailing separation mechanisms. Differences in diffusivity played a more dominant role than the competitive adsorption, and led to nitrogen selective membranes.

Novel Sustainable Composites Based on Poly(hydroxybutyrate-co-hydroxyvalerate) and Seagrass Beach-CAST Fibers: Performance and Degradability in Marine Environments.

PubMed

Seggiani, Maurizia; Cinelli, Patrizia; Balestri, Elena; Mallegni, Norma; Stefanelli, Eleonora; Rossi, Alessia; Lardicci, Claudio; Lazzeri, Andrea

2018-05-11

In order to produce sustainable, bio-based and highly biodegradable materials, composites based on poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) and fibers of Posidonia oceanica (PO), a dominant Mediterranean seagrass, were produced by simple melt mixing and characterized in terms of thermal stability, morphology and rheological/mechanical properties. In view of their potential application in marine environments, degradation of the developed composites was evaluated under simulated and real marine environmental conditions for 1 year. Using 10 wt % of acetyl tributyl citrate (ATBC) as a plasticizer, smooth processing was achieved for up to 30 wt % of PO fibers, despite the reduction of the melt fluidity observed with increasing fiber loading. The tensile modulus slightly increased (from 2 to 2.4 GPa) while the tensile strength and the elongation decreased (from 23.6 to 21.5 MPa and from 3.2 to 1.9%, respectively) by increasing the PO fiber content from 0 to 30 wt %. Interestingly, the impact resistance of the composites increased with the increasing of the PO content: the Charpy’s impact energy increased from 3.6 (without fiber) to 4.4 kJ/m² for the composite with 30 wt %. The results of the aerobic biodegradation under simulated marine conditions showed that the presence of PO fibers favored the physical disintegration of the composite increasing the biodegradation rate of the polymeric matrix: after 216 days, the composite with 20 wt % PO fibers showed a biodegradability of about 30% compared to 20% of the composite without fibers. Under real marine conditions, the specimens containing PO fibers showed higher weight losses and deterioration of tensile properties compared to those without fibers. Presumably, biodegradation occurred after colonization of the specimen, and the specimens with 20 wt % PO fibers showed well-developed biofilm consisting of bacteria and fungi on the surface after only 3 months of incubation in marine sediments, unlike the no-fiber specimens. Consequently, the persistence of an adequate mechanical performance for a relatively long period (1 year), due to a moderate rate of biodegradation in the marine environment, make the developed PHBV/PO composites particularly suitable for the production of relatively low-cost and biodegradable items which are usable in the sea and/or sand dunes, increasing the market opportunities for biopolymers such as PHBV and, at the same time, finding an eco-sustainable valorization for the PO fibrous residues accumulated in large quantities on Mediterranean beaches, which represents a problem for coastal municipalities.

Novel Sustainable Composites Based on Poly(hydroxybutyrate-co-hydroxyvalerate) and Seagrass Beach-CAST Fibers: Performance and Degradability in Marine Environments

PubMed Central

Mallegni, Norma; Stefanelli, Eleonora; Rossi, Alessia

2018-01-01

In order to produce sustainable, bio-based and highly biodegradable materials, composites based on poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) and fibers of Posidonia oceanica (PO), a dominant Mediterranean seagrass, were produced by simple melt mixing and characterized in terms of thermal stability, morphology and rheological/mechanical properties. In view of their potential application in marine environments, degradation of the developed composites was evaluated under simulated and real marine environmental conditions for 1 year. Using 10 wt % of acetyl tributyl citrate (ATBC) as a plasticizer, smooth processing was achieved for up to 30 wt % of PO fibers, despite the reduction of the melt fluidity observed with increasing fiber loading. The tensile modulus slightly increased (from 2 to 2.4 GPa) while the tensile strength and the elongation decreased (from 23.6 to 21.5 MPa and from 3.2 to 1.9%, respectively) by increasing the PO fiber content from 0 to 30 wt %. Interestingly, the impact resistance of the composites increased with the increasing of the PO content: the Charpy’s impact energy increased from 3.6 (without fiber) to 4.4 kJ/m2 for the composite with 30 wt %. The results of the aerobic biodegradation under simulated marine conditions showed that the presence of PO fibers favored the physical disintegration of the composite increasing the biodegradation rate of the polymeric matrix: after 216 days, the composite with 20 wt % PO fibers showed a biodegradability of about 30% compared to 20% of the composite without fibers. Under real marine conditions, the specimens containing PO fibers showed higher weight losses and deterioration of tensile properties compared to those without fibers. Presumably, biodegradation occurred after colonization of the specimen, and the specimens with 20 wt % PO fibers showed well-developed biofilm consisting of bacteria and fungi on the surface after only 3 months of incubation in marine sediments, unlike the no-fiber specimens. Consequently, the persistence of an adequate mechanical performance for a relatively long period (1 year), due to a moderate rate of biodegradation in the marine environment, make the developed PHBV/PO composites particularly suitable for the production of relatively low-cost and biodegradable items which are usable in the sea and/or sand dunes, increasing the market opportunities for biopolymers such as PHBV and, at the same time, finding an eco-sustainable valorization for the PO fibrous residues accumulated in large quantities on Mediterranean beaches, which represents a problem for coastal municipalities. PMID:29751601

Integrating remote sensing and subsurface geological data to characterize a tidally-influenced paleodrainage from the mid-late Holocene succession of the Po Delta Plain (Italy)

NASA Astrophysics Data System (ADS)

Giacomelli, Serena; Rossi, Veronica; Amorosi, Alessandro; Bruno, Luigi; Campo, Bruno; Ciampalini, Andrea; Civa, Andrea; de Souza Filho, Roberto Carlos; Sgavetti, Maria

2017-04-01

A tidally-influenced, mid-late Holocene paleodrainage system from the Po Delta Plain (N Adriatic Sea, Italy) is reconstructed coupling remote sensing (RS) and subsurface geological data. Optical satellite images, DTM LiDAR, soil reflectance spectral features and core stratigraphy were combined in a GIS environment following a fully integrated methodological approach. The stratigraphic significance of RS-derived data (traces) was defined in terms of both depositional facies and depth, furnishing new insights on the role of RS in reconstructing the recent evolution of paleodrainages in coastal-deltaic settings. Sixteen images from Landsat 7 ETM+ (Enhanced Thematic Mapper Plus), Landsat 8 OLI (Operational Land Imager), Sentinel-2 MSI (Multispectral Instruments), and Hyperion satellites were collected from the USGS and the Scientific Hub ESA-Copernicus on-line databases, and integrated with Google Earth imagery. The visual interpretation of the images, mostly based on the brightness contrast (high and low reflectance values) and aimed to the recognition of traces, has been facilitated by the RGB combinations of the spectral bands most sensitive to lithology and moisture content and supported by a semi-automatic processing, including unsupervised classification and the spectral bands Principal Component Analysis (PCA). Multitemporal analysis of satellite imagery have been also performed. Two main traces, interpreted as meanders, have been analyzed for their sedimentological and stratigraphic characteristics. Following a field survey aimed to describe the morphology, grain-size, colors, and accessory materials of surface deposits, 11 soil samples have been collected for the extraction of the reflectance spectral signature and coring along the traces and in adjacent areas (bright and dark portions). Cores have been sampled for benthic foraminifer/ostracod analysis (42 samples) and stratigraphic cross-sections were constructed transversal to the meandering traces. Nine radiocarbon ages allowed to set the depositional evolution of the two meanders into a definite chronological framework. The integrated, RS-stratigraphic methodological approach revealed a meandering paleodrainage system buried > 2 m below the ground level. Its surface visibility is guided by the spatial distribution of surface moisture, which mainly depends on subsurface stratigraphic architecture and, in particular, on the distribution of organic-rich deposits laterally to the migrating meanders. The formation and activity of the buried paleochannels dates back to the early Holocene highstand (6000-2500 cal yr BP), when a drainage system likely developed under tide-influenced conditions.

Experimental/Computational Approach to Accommodation Coefficients and its Application to Noble Gases on Aluminum Surface (Preprint)

DTIC Science & Technology

2009-02-03

computational approach to accommodation coefficients and its application to noble gases on aluminum surface Nathaniel Selden Uruversity of Southern Cahfornia, Los ...8217 ,. 0.’ a~ .......,..,P. • " ,,-0, "p"’U".. ,Po"D.’ 0.’P.... uro . P." FIG. 5: Experimental and computed radiometri~ force for argon (left), xenon

Ab Initio-Based Predictions of Hydrocarbon Combustion Chemistry

DTIC Science & Technology

2015-07-15

There are two prime objectives of the research. One is to develop and apply efficient methods for using ab initio potential energy surfaces (PESs...31-Mar-2015 Approved for Public Release; Distribution Unlimited Final Report: Ab Initio -Based Predictions of Hydrocarbon Combustion Chemistry The...Office P.O. Box 12211 Research Triangle Park, NC 27709-2211 hydrocarbon combustion, ab initio quantum chemistry, potential energy surfaces, chemical

Effective Surface Passivation of InP Nanowires by Atomic-Layer-Deposited Al2O3 with POx Interlayer.

PubMed

Black, L E; Cavalli, A; Verheijen, M A; Haverkort, J E M; Bakkers, E P A M; Kessels, W M M

2017-10-11

III/V semiconductor nanostructures have significant potential in device applications, but effective surface passivation is critical due to their large surface-to-volume ratio. For InP such passivation has proven particularly difficult, with substantial depassivation generally observed following dielectric deposition on InP surfaces. We present a novel approach based on passivation with a phosphorus-rich interfacial oxide deposited using a low-temperature process, which is critical to avoid P-desorption. For this purpose we have chosen a PO x layer deposited in a plasma-assisted atomic layer deposition (ALD) system at room temperature. Since PO x is known to be hygroscopic and therefore unstable in atmosphere, we encapsulate this layer with a thin ALD Al 2 O 3 capping layer to form a PO x /Al 2 O 3 stack. This passivation scheme is capable of improving the photoluminescence (PL) efficiency of our state-of-the-art wurtzite (WZ) InP nanowires by a factor of ∼20 at low excitation. If we apply the rate equation analysis advocated by some authors, we derive a PL internal quantum efficiency (IQE) of 75% for our passivated wires at high excitation. Our results indicate that it is more reliable to calculate the IQE as the ratio of the integrated PL intensity at room temperature to that at 10 K. By this means we derive an IQE of 27% for the passivated wires at high excitation (>10 kW cm -2 ), which constitutes an unprecedented level of performance for undoped InP nanowires. This conclusion is supported by time-resolved PL decay lifetimes, which are also shown to be significantly higher than previously reported for similar wires. The passivation scheme displays excellent long-term stability (>7 months) and is additionally shown to substantially improve the thermal stability of InP surfaces (>300 °C), significantly expanding the temperature window for device processing. Such effective surface passivation is a key enabling technology for InP nanowire devices such as nanolasers and solar cells.

Chemical Storage of Data

NASA Technical Reports Server (NTRS)

Bauschlicher, Charles W., Jr.; Ricca, Alessandra; Merkle, Ralph; Arnold, James O. (Technical Monitor)

1996-01-01

We investigate the possibility of storing data using H and F on a polymer to signify 0 and 1 bits. We show that the difference between the B-F and B-H interaction energies for either C5H5B or C3H3N2B is only slightly larger than the variation in B-F interaction energy with type of neighboring atoms. Pyridine (C5H5N) and (CH3)3P=O have a much larger difference in the H and F interaction energies. (CH3)3P=O may be better suited as a surface probe, because the interaction with neighboring data sites should be smaller.

Evaluation of a Silver-Embedded Ceramic Tablet as a Primary and Secondary Point-of-Use Water Purification Technology in Limpopo Province, S. Africa

PubMed Central

Ehdaie, Beeta; Rento, Chloe T.; Son, Veronica; Turner, Sydney S.; Samie, Amidou; Dillingham, Rebecca A.

2017-01-01

The World Health Organization (WHO) recognizes point-of-use water treatment (PoUWT) technologies as effective means to improve water quality. This paper investigates long-term performance and social acceptance of a novel PoUWT technology, a silver-infused ceramic tablet, in Limpopo Province, South Africa. When placed in a water storage container, the silver-embedded ceramic tablet releases silver ions into water, thereby disinfecting microbial pathogens and leaving the water safe for human consumption. As a result of its simplicity and efficiency, the silver-embedded ceramic tablet can serve as a stand-alone PoUWT method and as a secondary PoUWT to improve exisitng PoUWT methods, such as ceramic water filters. In this paper, three PoUWT interventions were conducted to evaluate the silver-embedded ceramic tablet: (1) the silver-embedded ceramic tablet as a stand-alone PoUWT method, (2) ceramic water filters stand-alone, and (3) a filter-tablet combination. The filter-tablet combination evaluates the silver-embedded ceramic tablet as a secondary PoUWT method when placed in the lower reservoir of the ceramic water filter system to provide residual disinfection post-filtration. Samples were collected from 79 households over one year and analyzed for turbidity, total silver levels and coliform bacteria. Results show that the silver-embedded ceramic tablet effectively reduced total coliform bacteria (TC) and E. coli when used as a stand-alone PoUWT method and when used in combination with ceramic water filters. The silver-embedded ceramic tablet’s performance as a stand-alone PoUWT method was comparable to current inexpensive, single-use PoUWT methods, demonstrating 100% and 75% median reduction in E. coli and TC, respectively, after two months of use. Overall, the the filter-tablet combination performed the best of the three interventions, providing a 100% average percent reduction in E. coli over one year. User surveys were also conducted and indicated that the silver-embedded ceramic tablet was simple to use and culturally appropriate. Also, silver levels in all treated water samples remained below 20 μg/L, significantly lower than the drinking water standard of 100 μg/L, making it safe for consumption. Long-term data demonstrates that the silver-embedded ceramic tablet has beneficial effects even after one year of use. This study demonstrates that the silver-embedded ceramic tablet can effectively improve water quality when used alone, or with ceramic water filters, to reduce rates of recontamination. Therefore, the tablet has the potential to provide a low-cost means to purify water in resource-limited settings. PMID:28095435

Evaluation of a Silver-Embedded Ceramic Tablet as a Primary and Secondary Point-of-Use Water Purification Technology in Limpopo Province, S. Africa.

PubMed

Ehdaie, Beeta; Rento, Chloe T; Son, Veronica; Turner, Sydney S; Samie, Amidou; Dillingham, Rebecca A; Smith, James A

2017-01-01

The World Health Organization (WHO) recognizes point-of-use water treatment (PoUWT) technologies as effective means to improve water quality. This paper investigates long-term performance and social acceptance of a novel PoUWT technology, a silver-infused ceramic tablet, in Limpopo Province, South Africa. When placed in a water storage container, the silver-embedded ceramic tablet releases silver ions into water, thereby disinfecting microbial pathogens and leaving the water safe for human consumption. As a result of its simplicity and efficiency, the silver-embedded ceramic tablet can serve as a stand-alone PoUWT method and as a secondary PoUWT to improve exisitng PoUWT methods, such as ceramic water filters. In this paper, three PoUWT interventions were conducted to evaluate the silver-embedded ceramic tablet: (1) the silver-embedded ceramic tablet as a stand-alone PoUWT method, (2) ceramic water filters stand-alone, and (3) a filter-tablet combination. The filter-tablet combination evaluates the silver-embedded ceramic tablet as a secondary PoUWT method when placed in the lower reservoir of the ceramic water filter system to provide residual disinfection post-filtration. Samples were collected from 79 households over one year and analyzed for turbidity, total silver levels and coliform bacteria. Results show that the silver-embedded ceramic tablet effectively reduced total coliform bacteria (TC) and E. coli when used as a stand-alone PoUWT method and when used in combination with ceramic water filters. The silver-embedded ceramic tablet's performance as a stand-alone PoUWT method was comparable to current inexpensive, single-use PoUWT methods, demonstrating 100% and 75% median reduction in E. coli and TC, respectively, after two months of use. Overall, the the filter-tablet combination performed the best of the three interventions, providing a 100% average percent reduction in E. coli over one year. User surveys were also conducted and indicated that the silver-embedded ceramic tablet was simple to use and culturally appropriate. Also, silver levels in all treated water samples remained below 20 μg/L, significantly lower than the drinking water standard of 100 μg/L, making it safe for consumption. Long-term data demonstrates that the silver-embedded ceramic tablet has beneficial effects even after one year of use. This study demonstrates that the silver-embedded ceramic tablet can effectively improve water quality when used alone, or with ceramic water filters, to reduce rates of recontamination. Therefore, the tablet has the potential to provide a low-cost means to purify water in resource-limited settings.

Effects of low and standard intra-abdominal pressure on systemic inflammation and immune response in laparoscopic adrenalectomy: A prospective randomised study.

PubMed

Schietroma, Mario; Pessia, Beatrice; Stifini, Derna; Lancione, Laura; Carlei, Francesco; Cecilia, Emanuela Marina; Amicucci, Gianfranco

2016-01-01

The advantages of laparoscopic adrenalectomy (LA) over open adrenalectomy are undeniable. Nevertheless, carbon dioxide (CO2) pneumoperitoneum may have an unfavourable effect on the local immune response. The aim of this study was to compare changes in the systemic inflammation and immune response in the early post-operative (p.o.) period after LA performed with standard and low-pressure CO2 pneumoperitoneum. We studied, in a prospective randomised study, 51 patients consecutively with documented adrenal lesion who had undergone a LA: 26 using standard-pressure (12-14 mmHg) and 25 using low-pressure (6-8 mmHg) pneumoperitoneum. White blood cells (WBC), peripheral lymphocyte subpopulation, human leucocyte antigen-DR (HLA-DR), neutrophil elastase, interleukin (IL)-6 and IL-1, and C-reactive protein (CRP) were investigated. Significantly higher concentrations of neutrophil elastase, IL-6 and IL-1 and CRP were detected p.o. in the standard-pressure group of patients in comparison with the low-pressure group (P < 0.05). A statistically significant change in HLA-DR expression was recorded p.o. at 24 h, as a reduction of this antigen expressed on the monocyte surface in patients from the standard group; no changes were noted in low-pressure group patients (P < 0.05). This study demonstrated that reducing the pressure of the pneumoperitoneum to 6-8 mmHg during LA reduced p.o. inflammatory response and averted p.o. immunosuppression.

Dying at home in rural residential aged care: A mixed-methods study in the Snowy Monaro region, Australia.

PubMed

Rainsford, Suzanne; Phillips, Christine B; Glasgow, Nicholas J; MacLeod, Roderick D; Wiles, Robert B

2018-05-16

Residential aged care (RAC) is a significant provider of end-of-life care for people aged 65 years and older. Rural residents perceive themselves as different to their urban counterparts. Most studies describing place of death (PoD) in RAC are quantitative and reflect an urban voice. Using a mixed-methods design, this paper examines the PoD of 80 RAC residents (15 short-stay residents who died in RAC during respite or during an attempted step-down transition from hospital to home, and 65 permanent residents), within the rural Snowy Monaro region, Australia, who died between 1 February 2015 and 31 May 2016. Death data were collected from local funeral directors, RAC facilities, one multi-purpose heath service and obituary notices in the local media. The outcome variable was PoD: RAC, local hospital or out-of-region tertiary hospital. For the permanent RAC residents, the outcome of interest was dying in RAC or dying in hospital. Cross tabulations by PoD and key demographic data were performed. Pearson Chi squared tests and exact p-values were used to determine if any of the independent variables were associated with PoD. Using an ethnographic approach, data were collected from 12 face-to-face, open-ended interviews with four RAC residents, with a life expectancy of ≤6 months, and six family caregivers. Interviews were audio-recorded, transcribed and analysed thematically. Fifty-one (78.5%) of the permanent residents died in RAC; 21.5% died in hospital. Home was the initial preferred POD for most interviewed participants; most eventually accepted the transfer to RAC. Long-term residents considered RAC to be their "home"-a familiar place, and an important part of their rural community. The participants did not consider a transfer to hospital to be necessary for end-of-life care. Further work is required to explore further the perspectives of rural RAC residents and their families, and if transfers to hospital are avoidable. © 2018 John Wiley & Sons Ltd.

Person-job and person-organization fits: Co-op fits in an aerospace engineering environment

NASA Astrophysics Data System (ADS)

Urban, Anthony John, Jr.

This dissertation research was a replication of a quantitative study completed by Dr. Cynthia Shantz at Wayne State University during 2003. The intent of the research was to investigate the fits of college students who participated in cooperative academic-work programs (co-ops) to employment positions within aerospace engineering. The objective of investigating person-job (P-J) and person-organization (P-O) fits was to determine if variables could be identified that indicated an individual's aptitude to complete successfully aerospace engineering standard work. Research participants were co-op employees who were surveyed during their employment to identify indications of their fits into their organization and job assignments. Dr. Shantz's research led to the thought employment success might increase when P-J and P-O fits increase. For example, reduced initial training investments and increased employee retention might result with improved P-O and P-J fits. Research data were gathered from surveys of co-ops who worked at a Connecticut aerospace engineering company. Data were collected by distributing invitations to co-ops to participate in three online surveys over a 9-11 week period. Distribution of survey invitations was accomplished through the Human Resources Department to ensure that respondent identities were maintained private. To protect anonymity and privacy further, no identifying information about individuals or the company is published. However, some demographic information was collected to ensure that correlations were based on valid and reliable data and research and analysis methods. One objective of this research was to determine if co-op characteristics could be correlated with successful employment in an aerospace engineering environment. A second objective was to determine if P-J and P-O fits vary over time as co-ops become increasing familiar with their assignments, organization, and environment. Understanding and incorporating the use P-J and P-O fits characteristics in the employment preparation and screening process may benefit aerospace engineering companies, co-ops, and academia through gains realized in reduced employment recruitment time and retention cost, student improvement in preparation to fit into aerospace engineering environments, and increases in pre- and post-graduation job placement rates.

Human absorption and retention of polonium-210 from caribou meat.

PubMed

Thomas, P A; Fisenne, I; Chorney, D; Baweja, A S; Tracy, B L

2001-01-01

The gastrointestinal (GI) absorption factors and the biological retention times for polonium were determined for a group of 14 volunteers--seven men and seven women--from Saskatoon, Saskatchewan, Canada. Each volunteer consumed 2.0 kg of caribou meat containing known amounts of naturally occurring 210Po. Urine and faecal samples were collected for up to 65 days after meat consumption and analysed for 210Po. The average GI absorption factor for the 14 volunteers was 56 +/- 4% (range = 31-71%), not significantly different from the ICRP value of 50%. About 3% of absorbed polonium underwent prompt excretion by the urinary pathway. The remainder was retained by the body with a half-time >100 days, compared to the ICRP value of 50 days. The effect of these findings increases the dose estimate for ingestion of 210Po in food by a factor of 1.5 to 3.5. Thus, background doses to people consuming caribou and reindeer may be higher than previously thought.

Catalytic fast pyrolysis of biomass impregnated with potassium phosphate in a hydrogen atmosphere for the production of phenol and activated carbon

NASA Astrophysics Data System (ADS)

Lu, Qiang; Zhang, Zhen-xi; Wang, Xin; Guo, Hao-qiang; Cui, Min-shu; Yang, Yong-ping

2018-02-01

A new technique was proposed to co-produce phenol and activated carbon (AC) from catalytic fast pyrolysis of biomass impregnated with K3PO4 in a hydrogen atmosphere, followed by activation of the pyrolytic solid residues. Lab-scale catalytic fast pyrolysis experiments were performed to quantitatively determine the pyrolytic product distribution, as well as to investigate the effects of several factors on the phenol production, including pyrolysis atmosphere, catalyst type, biomass type, catalytic pyrolysis temperature, and catalyst impregnation content. In addition, the pyrolytic solid residues were activated to prepare ACs with high specific surface areas. The results indicated that phenol could be obtained due to the synergistic effects of K3PO4 and hydrogen atmosphere, with the yield and selectivity reaching 5.3 wt% and 17.8% from catalytic fast pyrolysis of poplar wood with 8 wt% K3PO4 at 550 oC in a hydrogen atmosphere. This technique was adaptable to different woody materials for phenol production. Moreover, gas product generated from the pyrolysis process was feasible to be recycled to provide the hydrogen atmosphere, instead of extra hydrogen supply. In addition, the pyrolytic solid residue was suitable for AC preparation, using CO2 activation method, the specific surface area was as high as 1605 m2/g.

Distinct crystallinity and orientations of hydroxyapatite thin films deposited on C- and A-plane sapphire substrates

NASA Astrophysics Data System (ADS)

Akazawa, Housei; Ueno, Yuko

2014-10-01

We report how the crystallinity and orientation of hydroxyapatite (HAp) films deposited on sapphire substrates depend on the crystallographic planes. Both solid-phase crystallization of amorphous HAp films and crystallization during sputter deposition at elevated temperatures were examined. The low-temperature epitaxial phase on C-plane sapphire substrates has c-axis orientated HAp crystals regardless of the crystallization route, whereas the preferred orientation switches to the (310) direction at higher temperatures. Only the symmetric stretching mode (ν1) of PO43- units appears in the Raman scattering spectra, confirming well-ordered crystalline domains. In contrast, HAp crystals grown on A-plane sapphire substrates are always oriented toward random orientations. Exhibiting all vibrational modes (ν1, ν3, and ν4) of PO43- units in the Raman scattering spectra reflects random orientation, violating the Raman selection rule. If we assume that Raman intensities of PO43- units represent the crystallinity of HAp films, crystallization terminating the surface with the C-plane is hindered by the presence of excess H2O and OH species in the film, whereas crystallization at random orientations on the A-plane sapphire is rather promoted by these species. Such contrasting behaviors between C-plane and A-plane substrates will reflect surface-plane dependent creation of crystalline seeds and eventually determine the orientation of resulting HAp films.

Catalytic Fast Pyrolysis of Biomass Impregnated with Potassium Phosphate in a Hydrogen Atmosphere for the Production of Phenol and Activated Carbon

PubMed Central

Lu, Qiang; Zhang, Zhen-xi; Wang, Xin; Guo, Hao-qiang; Cui, Min-shu; Yang, Yong-ping

2018-01-01

A new technique was proposed to co-produce phenol and activated carbon (AC) from catalytic fast pyrolysis of biomass impregnated with K3PO4 in a hydrogen atmosphere, followed by activation of the pyrolytic solid residues. Lab-scale catalytic fast pyrolysis experiments were performed to quantitatively determine the pyrolytic product distribution, as well as to investigate the effects of several factors on the phenol production, including pyrolysis atmosphere, catalyst type, biomass type, catalytic pyrolysis temperature, and catalyst impregnation content. In addition, the pyrolytic solid residues were activated to prepare ACs with high specific surface areas. The results indicated that phenol could be obtained due to the synergistic effects of K3PO4 and hydrogen atmosphere, with the yield and selectivity reaching 5.3 wt% and 17.8% from catalytic fast pyrolysis of poplar wood with 8 wt% K3PO4 at 550°C in a hydrogen atmosphere. This technique was adaptable to different woody materials for phenol production. Moreover, gas product generated from the pyrolysis process was feasible to be recycled to provide the hydrogen atmosphere, instead of extra hydrogen supply. In addition, the pyrolytic solid residue was suitable for AC preparation, using CO2 activation method, the specific surface area was as high as 1,605 m2/g. PMID:29515994

Catalytic Fast Pyrolysis of Biomass Impregnated with Potassium Phosphate in a Hydrogen Atmosphere for the Production of Phenol and Activated Carbon.

PubMed

Lu, Qiang; Zhang, Zhen-Xi; Wang, Xin; Guo, Hao-Qiang; Cui, Min-Shu; Yang, Yong-Ping

2018-01-01

A new technique was proposed to co-produce phenol and activated carbon (AC) from catalytic fast pyrolysis of biomass impregnated with K 3 PO 4 in a hydrogen atmosphere, followed by activation of the pyrolytic solid residues. Lab-scale catalytic fast pyrolysis experiments were performed to quantitatively determine the pyrolytic product distribution, as well as to investigate the effects of several factors on the phenol production, including pyrolysis atmosphere, catalyst type, biomass type, catalytic pyrolysis temperature, and catalyst impregnation content. In addition, the pyrolytic solid residues were activated to prepare ACs with high specific surface areas. The results indicated that phenol could be obtained due to the synergistic effects of K 3 PO 4 and hydrogen atmosphere, with the yield and selectivity reaching 5.3 wt% and 17.8% from catalytic fast pyrolysis of poplar wood with 8 wt% K 3 PO 4 at 550°C in a hydrogen atmosphere. This technique was adaptable to different woody materials for phenol production. Moreover, gas product generated from the pyrolysis process was feasible to be recycled to provide the hydrogen atmosphere, instead of extra hydrogen supply. In addition, the pyrolytic solid residue was suitable for AC preparation, using CO 2 activation method, the specific surface area was as high as 1,605 m 2 /g.

Auto-cortex of crystalline lens-induced iris neovascularization

PubMed Central

Liu, Lin; Li, Yong-Ping; Zhang, Bo; Zhang, Wen-Xin

2012-01-01

AIM To investigate auto-cortex of crystalline lens induced iris neovascularization (INV). METHODS Thirty-six eyes of 36 guinea-pigs were included and divided into three groups randomly in this cohort study. Group A: the right lens nucleus was extracted and the remaining cortical lens material was aspirated thoroughly. Group B: the lens was removed and 30µL precipitated lens cortex was injected into the anterior chamber again. Group C: aspirated the lens cortex of the left eyes and inject them into the right anterior chambers about 10µL. Clinical changes were followed by slit-lamp examination and photograph. The eye balls were enucleated at the day of 2, 4, 7, 11, 13, 17 after operation. HE was used to detect the pathological changes. RESULTS Group A: INV had not been observed until the end of empirical study. The stromal layer contained thick wall vessels, without expansion. Group B: All eyes developed INV. Postoperative (po) 7 days; the eyes developed intense and extensive INV. The vessels of iris expanded remarkably and neovascularization was observed erupting from it's lateral wall and stretching towards the anterior surface. Po11 days, INV regressed gradually after lens cortex had been absorbed. Group C: Po four (4) days, new blood vessels liking red line were presented on the anterior surface of the iris and they were not obvious. CONCLUSION Anterior chamber inside lens coriaceous can induce iris new blood vessels. PMID:22553749

76 FR 40339 - Patent Prosecution Highway (PPH) Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-08

... DEPARTMENT OF COMMERCE Patent and Trademark Office Patent Prosecution Highway (PPH) Program ACTION: Proposed collection; comment request. SUMMARY: The United States Patent and Trademark Office (USPTO), as... Information Officer, United States Patent and Trademark Office, P.O. Box 1450, Alexandria, VA 22313-1450...

Preparation of LiFePO{sub 4} with inverse opal structure and its satisfactory electrochemical properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu Junbiao; Tang Zilong; Zhang Zhongtai

Phase pure, well-crystallized and homogeneous LiFePO{sub 4} powder with inverse opal structure was obtained by calcining the precursors of Li{sup +}, Fe{sup 2+} and PO{sub 4} {sup 3-} in the presence of organic template of poly(styrene-methyl methacrylate-acrylic acid) latex micro-spheres under nitrogen atmosphere. The resultant products were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), chemical titration, Fourier transform infrared (FTIR) and Land 2001A electrochemical measurement system. Results indicated that after the decomposition of organic template, inverse opal structure and conductive carbon were left in the resultant products. With the large specific surface areamore » resulting from inverse opal structure and with the conductive carbon, the products delivered satisfactory capacity and superior rate capability at room temperature, i.e., over 100 mAh/g at the high current density of 5.9C.« less

Xanthan gum production using jackfruit-seed-powder-based medium: optimization and characterization.

PubMed

Felicia Katherine, R; Muthukumaran, C; Sharmila, G; Manoj Kumar, N; Tamilarasan, K; Jaiganesh, R

2017-08-01

Xanthan gum (XG) production by Xanthomonas campestris NCIM 2961 using jackfruit seed powder (JSP) as a novel substrate was reported. Central composite design (CCD) of response surface method (RSM) was used to evaluate the linear and interaction effects of five medium variables (JSP, peptone, citric acid, K 2 HPO 4 and KH 2 PO 4 ) for XG production. Maximum XG production (51.62 g/L) was observed at the optimum level of JSP (4 g/L), peptone (0.93 g/L), citric acid (0.26 g/L), K 2 HPO 4 (1.29 g/L) and KH 2 PO 4 (0.5 g/L). K 2 HPO 4 and KH 2 PO 4 were found as significant medium components, which served as buffering agents as well as nutrients for X. campestris growth. The obtained biopolymer was characterized as XG by XRD and FTIR analysis. Results of this study revealed that JSP was found to be a suitable low cost substrate for XG production.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Shan, E-mail: coralgao@hotmail.com; Engineering Ceramics Key Laboratory of Shandong Province, Shandong University, Jinan 250061; Sun, Kangning, E-mail: sunkangning@sdu.edu.cn

Highlights: ► We succeeded in synthesizing hydroxyapatite nano fibers by a chemical method. ► The reaction temperature is only 90 °C. ► The synthetic hydroxyapatite nano fiber is single crystal. - Abstract: We report a novel chemical precipitation route for the synthesis of hydroxyapatite (Ca{sub 10}(PO{sub 4}){sub 6}(OH){sub 2}, HA) fibers using surfactants as templates. Fourier transform infrared spectroscopy (FTIR) and powder X-ray diffraction (PXRD) reveal the characteristic peaks of HA. Transmission electron microscope (TEM) and high-resolution TEM revealed the nano structure, crystallinity and morphology of the HA fibers. The morphology of the HA fibers after calcinations were characterized bymore » scanning electron microscope (SEM). Br{sup −} ions were quickly replaced by the excess PO{sub 4}{sup 3−} ions in the solution after the addition of cetyltrime-thylammonium bromide (CTAB). Meanwhile, CTAB formed a rod-like micelles. Precursors reacted with PO{sub 4}{sup 3−} at the surface of CTAB micelles and finally formed the nanofiber structure.« less

Development of a tagged source of Pb-206 nuclei

NASA Astrophysics Data System (ADS)

Cutter, J.; Godfrey, B.; Hillbrand, S.; Irving, M.; Manalaysay, A.; Minaker, Z.; Morad, J.; Tripathi, M.

2018-02-01

There is a particular class of unavoidable backgrounds that plague low-background experiments and rare event searches, particularly those searching for nuclear recoil event signatures: decaying daughters of the 238U nuclear decay chain, which result from radon plate-out on detector materials. One such daughter isotope, 210Po, undergoes α-decay and produces a recoiling 103 keV 206Pb nucleus. To characterize this important background in the context of noble element detectors, we have implemented a triggered source for these 206Pb recoils in a dual-phase xenon time projection chamber (Xe TPC) within the Davis Xenon R&D testbed system (DAX). By adhering 210Po to the surface of a PIN diode and electrically floating the diode on the cathode of the TPC, we tag the α signals produced in the PIN diode and trigger on the correlated nuclear recoils in the liquid xenon (LXe). We discuss our methods for 210Po deposition, electronic readout of the PIN diode signals at high voltage, and analysis methods for event selection.

Strong Nanocomposites with Ca, PO4, and F Release for Caries Inhibition

PubMed Central

Xu, H.H.K.; Weir, M.D.; Sun, L.; Moreau, J.L.; Takagi, S.; Chow, L.C.; Antonucci, J.M.

2010-01-01

This article reviews recent studies on: (1) the synthesis of novel calcium phosphate and calcium fluoride nanoparticles and their incorporation into dental resins to develop nanocomposites; (2) the effects of key microstructural parameters on Ca, PO4, and F ion release from nanocomposites, including the effects of nanofiller volume fraction, particle size, and silanization; and (3) mechanical properties of nanocomposites, including water-aging effects, flexural strength, fracture toughness, and three-body wear. This article demonstrates that a major advantage of using the new nanoparticles is that high levels of Ca, PO4, and F release can be achieved at low filler levels in the resin, because of the high surface areas of the nanoparticles. This leaves room in the resin for substantial reinforcement fillers. The combination of releasing nanofillers with stable and strong reinforcing fillers is promising to yield a nanocomposite with both stress-bearing and caries-inhibiting capabilities, a combination not yet available in current materials. PMID:19948941

Three-Dimensional, Fibrous Lithium Iron Phosphate Structures Deposited by Magnetron Sputtering.

PubMed

Bünting, Aiko; Uhlenbruck, Sven; Sebold, Doris; Buchkremer, H P; Vaßen, R

2015-10-14

Crystalline, three-dimensional (3D) structured lithium iron phosphate (LiFePO4) thin films with additional carbon are fabricated by a radio frequency (RF) magnetron-sputtering process in a single step. The 3D structured thin films are obtained at deposition temperatures of 600 °C and deposition times longer than 60 min by using a conventional sputtering setup. In contrast to glancing angle deposition (GLAD) techniques, no tilting of the substrate is required. Thin films are characterized by X-ray diffraction (XRD), Raman spectrospcopy, scanning electron microscopy (SEM), cyclic voltammetry (CV), and galvanostatic charging and discharging. The structured LiFePO4+C thin films consist of fibers that grow perpendicular to the substrate surface. The fibers have diameters up to 500 nm and crystallize in the desired olivine structure. The 3D structured thin films have superior electrochemical properties compared with dense two-dimensional (2D) LiFePO4 thin films and are, hence, very promising for application in 3D microbatteries.

Half-lives of 221Fr, 217At, 213Bi, 213Po and 209Pb from the 225Ac decay series.

PubMed

Suliman, G; Pommé, S; Marouli, M; Van Ammel, R; Stroh, H; Jobbágy, V; Paepen, J; Dirican, A; Bruchertseifer, F; Apostolidis, C; Morgenstern, A

2013-07-01

The half-lives of (221)Fr, (217)At, (213)Bi, (213)Po, and (209)Pb were measured by means of an ion-implanted planar Si detector for alpha and beta particles emitted from weak (225)Ac sources or from recoil sources, which were placed in a quasi-2π counting geometry. Recoil sources were prepared by collecting atoms from an open (225)Ac source onto a glass substrate. The (221)Fr and (213)Bi half-lives were determined by following the alpha particle emission rate of recoil sources as a function of time. Similarly, the (209)Pb half-life was determined from the beta particle count rate. The shorter half-lives of (217)At and (213)Po were deduced from delayed coincidence measurements on weak (225)Ac sources using digital data acquisition in list mode. The resulting values: T1/2((221)Fr)=4.806 (6) min, T1/2((217)At)=32.8 (3)ms, T1/2((213)Bi)=45.62 (6)min, T1/2((213)Po)=3.708 (8) μs, and T1/2((209)Pb)=3.232 (5)h were in agreement only with the best literature data. Copyright © 2013 Elsevier Ltd. All rights reserved.

Technologically enhanced 210Pb and 210Po in iron and steel industry.

PubMed

Khater, Ashraf E M; Bakr, Wafaa F

2011-05-01

Iron and steel manufacture has been ranked as the largest industrial source of environmental contamination in the USA; the wastes generated in their production processes contain heavy elements that can be a source of contamination, and natural radionuclides that can produce an occupational and/or public radiological impact. In this work the potential occupational effective dose rate (μSv/y) due to inhalation in four integrated steel-making factories from Egypt has been evaluated, by assuming a well defined scenario and with basis in the (210)Pb and (210)Po activity concentrations determined in ore and wastes collected in the aforementioned factories. Activity concentrations, in Bq/kg, of (210)Pb and (210)Po, and leachable Pb and Fe were measured using gamma-ray spectrometry based on HPGe detector, alpha particle spectrometry based on PIPS detector, and inductively coupled plasma-mass spectrometry (ICP-MS). Levels of (210)Pb and (210)Po in the range of

3D crustal structure of the Alpine belt and foreland basins as imaged by ambient-noise surface wave

NASA Astrophysics Data System (ADS)

Molinari, Irene; Morelli, Andrea; Cardi, Riccardo; Boschi, Lapo; Poli, Piero; Kissling, Edi

2016-04-01

We derive a 3-D crustal structure (S wave velocity) underneath northern Italy and the wider Alpine region, from an extensive data set of measurements of Rayleigh-wave phase- and group-velocities from ambient noise correlation among all seismographic stations available to date in the region, via a constrained tomographic inversion made to honor detailed active source reflection/refraction profiles and other geological information. We first derive a regional-scale surface wave tomography from ambient-noise-based phase- and group- surface wave velocity observations (Verbeke et al., 2012). Our regional 3D model (Molinari et al., 2015) shows the low velocity area beneath the Po Plain and the Molasse basin; the contrast between the low-velocity crust of the Adriatic domain and the high-velocity crust of the Tyrrhenian domain is clearly seen, as well as an almost uniform crystalline crust beneath the Alpine belt. However, higher frequency data can be exploited to achieve higher resolution images of the Po Plain and Alpine foreland 3D crustal structure. We collected and analyze one year of noise records (2011) of ~100 North Italy seismic broadband stations, we derive the Green functions between each couple of stations and we measure the phase- and group-Rayleigh wave velocity. We conduct a suite of linear least squares inversion of both phase- and group-velocity data, resulting in 2-D maps of Rayleigh-wave phase and group velocity at periods between 3 and 40s with a resolution of 0.1x0.1 degrees. The maps are then inverted to get the 3D structure with unprecedented details. We present here our results, we compare them with other studies, and we discuss geological/geodynamical implications. We believe that such a model stands for the most up-to-date seismological information on the crustal structure of the Alpine belt and foreland basins, and it can represent a reliable reference for further, more detailed, studies to come, based on the high seismograph station density being accomplished by the AlpArray project.

[Influence of different porcelain surface treatment method on the bonding of metal brackets to porcelain].

PubMed

Fan, Cun-Hui; Chen, Jie; Liu, Xin-Qiang; Ma, Xin

2005-08-01

To investigate the influence of different porcelain surface treatment methods on the shear bond strength of metal brackets bonded to porcelain. 80 porcelain facets were divided randomly into two groups according to different adhesive material that was used to bond metal brackets. Adhesive material were Jing-Jin enamel adhesive and light-cured composite resin. Each group was further divided into 4 subgroups according to different surface treatment methods, which were acid etching with 37% phosphoric acid (H3PO4), acid etching with 9.6% hydrofluoric acid (HF), deglazing by grinding and silanating the porcelain surface. All specimens were stored in 37 degrees C water for 24 hours and then the shear bond strength and the porcelain fracture after debonding was determined. The porcelain surfaces after HF etching, H3PO4 etching and deglazing by grinding were examined by scanning electron microscopy respectively. The shear bond strengths in the HF etching groups, the deglazing groups and the silanating groups were much greater than that in the phosphoric etching groups (P < 0.01). Adequate orthodontic bonding strength was achieved both when bonded with light-cured composite resin after deglazing by grinding and when bonded with either of these adhesives after HF etching or surface silanating. There were no differences in the rates of porcelain fractures among groups (P > 0.05). HF etching, deglazing by grinding and silanating can all increase the shear bond strength between metal bracket and porcelain. Surface silanating of porcelain is a better surface treatment when metal brackets bonded to porcelain.

Expected Performance of the Upcoming Surface Water and Ocean Topography Mission Measurements of River Height, Width, and Slope

NASA Astrophysics Data System (ADS)

Wei, R.; Frasson, R. P. M.; Williams, B. A.; Rodriguez, E.; Pavelsky, T.; Altenau, E. H.; Durand, M. T.

2017-12-01

The upcoming Surface Water and Ocean Topography (SWOT) mission will measure river widths and water surface elevations of rivers wider than 100 m. In preparation for the SWOT mission, the Jet Propulsion Laboratory built the SWOT hydrology simulator with the intent of generating synthetic SWOT overpasses over rivers with realistic error characteristics. These synthetic overpasses can be used to guide the design of processing methods and data products, as well as develop data assimilation techniques that will incorporate the future SWOT data into hydraulic and hydrologic models as soon as the satellite becomes operational. SWOT simulator uses as inputs water depth, river bathymetry, and the surrounding terrain digital elevation model to create simulated interferograms of the study area. Next, the simulator emulates the anticipated processing of SWOT data by attempting to geolocate and classify the radar returns. The resulting cloud of points include information on water surface elevation, pixel area, and surface classification (land vs water). Finally, we process the pixel clouds by grouping pixels into equally spaced nodes located at the river centerline. This study applies the SWOT simulator to six different rivers: Sacramento River, Tanana River, Saint Lawrence River, Platte River, Po River, and Amazon River. This collection of rivers covers a range of size, slope, and planform complexity with the intent of evaluating the impact of river width, slope, planform complexity, and surrounding topography on the anticipated SWOT height, width, and slope error characteristics.

A geographic information system to predict soil erosion potential in rural transportation construction project

DOT National Transportation Integrated Search

1995-06-30

Topographic surface modeling using a Geographic Information System (GIS) can be useful for the prediction of soil erosion resulting from highway construction projects. The assumption is that terrain, along with other parameters, will influence the po...

Hydroxyapatite formation on graphene oxide modified with amino acids: arginine versus glutamic acid

PubMed Central

Tavafoghi, M.; Brodusch, N.; Gauvin, R.; Cerruti, M.

2016-01-01

Hydroxyapatite (HA, Ca5(PO4)3OH) is the main inorganic component of hard tissues, such as bone and dentine. HA nucleation involves a set of negatively charged phosphorylated proteins known as non-collagenous proteins (NCPs). These proteins attract Ca2+ and PO43− ions and increase the local supersaturation to a level required for HA precipitation. Polar and charged amino acids (AAs) are highly expressed in NCPs, and seem to be responsible for the mineralizing effect of NCPs; however, the individual effect of these AAs on HA mineralization is still unclear. In this work, we investigate the effect of a negatively charged (Glu) and positively charged (Arg) AA bound to carboxylated graphene oxide (CGO) on HA mineralization in simulated body fluids (SBF). Our results show that Arg induces HA precipitation faster and in larger amounts than Glu. We attribute this to the higher stability of the complexes formed between Arg and Ca2+ and PO43− ions, and also to the fact that Arg exposes both carboxyl and amino groups on the surface. These can electrostatically attract both Ca2+ and PO43− ions, thus increasing local supersaturation more than Glu, which exposes carboxyl groups only. PMID:26791001

Hydroxyapatite formation on graphene oxide modified with amino acids: arginine versus glutamic acid.

PubMed

Tavafoghi, M; Brodusch, N; Gauvin, R; Cerruti, M

2016-01-01

Hydroxyapatite (HA, Ca5(PO4)3OH) is the main inorganic component of hard tissues, such as bone and dentine. HA nucleation involves a set of negatively charged phosphorylated proteins known as non-collagenous proteins (NCPs). These proteins attract Ca(2+) and PO4(3-) ions and increase the local supersaturation to a level required for HA precipitation. Polar and charged amino acids (AAs) are highly expressed in NCPs, and seem to be responsible for the mineralizing effect of NCPs; however, the individual effect of these AAs on HA mineralization is still unclear. In this work, we investigate the effect of a negatively charged (Glu) and positively charged (Arg) AA bound to carboxylated graphene oxide (CGO) on HA mineralization in simulated body fluids (SBF). Our results show that Arg induces HA precipitation faster and in larger amounts than Glu. We attribute this to the higher stability of the complexes formed between Arg and Ca(2+) and PO4(3-) ions, and also to the fact that Arg exposes both carboxyl and amino groups on the surface. These can electrostatically attract both Ca(2+) and PO4(3-) ions, thus increasing local supersaturation more than Glu, which exposes carboxyl groups only. © 2016 The Author(s).

The influence of avian biovectors on mercury speciation in a bog ecosystem.

PubMed

Kickbush, Jocelyn C; Mallory, Mark L; Murimboh, John D; Rand, Jennie; Klapstein, Sara J; Loder, Amanda L; Hill, Nicholas M; O'Driscoll, Nelson J

2018-05-08

Methylmercury (MeHg) is a neurotoxin and endocrine disruptor that bioaccumulates and biomagnifies through trophic levels, resulting in potentially hazardous concentrations. Although wetlands are known hotspots for mercury (Hg) methylation, the effects of avian biovectors on these processes are poorly understood. We examined Hg speciation and distribution in shallow groundwater and surface water from a raised-bog with over 30years of avian biovector (herring gulls Larus argentatus and great black-backed gulls Larus marinus) colonization and guano input. Compared to the reference site, the avian-impacted bog had elevated concentrations of total dissolved organic carbon (TOC), total Hg, MeHg, phosphate (PO 4 3- ), and other trace metals, notably Pb, As, Cd and Ni. Spatial interpolation showed that the densest area of gull nesting was co-located with areas that had the highest concentrations of PO 4 3- , MeHg, As and Cd, but not total mercury (THg), and models suggested that Mn, PO 4 3- , and dissolved TOC were strong predictors of MeHg. Our findings suggest that while these gulls may not be a significant source of Hg, the excess of PO 4 3- (a well recognised component of guano) and the subsequent changes in water chemistry due to avian biovector subsidies may increase net Hg methylation. Copyright © 2018 Elsevier B.V. All rights reserved.

A prospective randomized study of systemic inflammation and immune response after laparoscopic nissen fundoplication performed with standard and low-pressure pneumoperitoneum.

PubMed

Schietroma, Mario; Carlei, Francesco; Cecilia, Emanuela M; Piccione, Federica; Sista, Federico; De Vita, Fabiola; Amicucci, Gianfranco

2013-04-01

The aim of this study was to compare changes in the systemic inflammation and immune response in the early postoperative (p.o.) period after laparoscopic Nissen fundoplication (LNF) was performed with standard-pressure and low-pressure carbon dioxide pneumoperitoneum. We studied 68 patients with documented gastroesophageal reflux disease and who underwent a LNF: 35 using standard-pressure (12 to 14 mmHg) and 33 low-pressure (6 to 8 mmHg) pneumoperitoneum. White blood cells, peripheral lymphocytes subpopulation, human leukocyte antigen-DR, neutrophil elastase, interleukin (IL)-6 and IL-1, and C-reactive protein were investigated. A significantly higher concentration of neutrophil elastase, IL-6 and IL-1, and C-reactive protein was detected postoperatively in the standard-pressure group of patients in comparison with the low-pressure group (P<0.05). A statistically significant change in human leukocyte antigen-DR expression was recorded p.o. at 24 hours, as a reduction of this antigen expressed on monocyte surface in patients from standard group; no changes were noted in low-pressure group patients (P<0.05). This study demonstrated that reducing the pressure of the pneumoperitoneum to 6 to 8 mm Hg during LNF is reduced p.o. inflammatory response and avoided p.o. immunosuppression.

Synthesis and Electrocatalytic Activity of Ammonium Nickel Phosphate, [NH4]NiPO4·6H2O, and β-Nickel Pyrophosphate, β-Ni2P2O7: Catalysts for Electrocatalytic Decomposition of Urea.

PubMed

Meguerdichian, Andrew G; Jafari, Tahereh; Shakil, Md R; Miao, Ran; Achola, Laura A; Macharia, John; Shirazi-Amin, Alireza; Suib, Steven L

2018-02-19

Electrocatalytic decomposition of urea for the production of hydrogen, H 2, for clean energy applications, such as in fuel cells, has several potential advantages such as reducing carbon emissions in the energy sector and environmental applications to remove urea from animal and human waste facilities. The study and development of new catalyst materials containing nickel metal, the active site for urea decomposition, is a critical aspect of research in inorganic and materials chemistry. We report the synthesis and application of [NH 4 ]NiPO 4 ·6H 2 O and β-Ni 2 P 2 O 7 using in situ prepared [NH 4 ] 2 HPO 4 . The [NH 4 ]NiPO 4 ·6H 2 O is calcined at varying temperatures and tested for electrocatalytic decomposition of urea. Our results indicate that [NH 4 ]NiPO 4 ·6H 2 O calcined at 300 °C with an amorphous crystal structure and, for the first time applied for urea electrocatalytic decomposition, had the greatest reported electroactive surface area (ESA) of 142 cm 2 /mg and an onset potential of 0.33 V (SCE) and was stable over a 24-h test period.

Determination of the volume activity concentration of alpha artificial radionuclides with alpha spectrometer.

PubMed

Liu, B; Zhang, Q; Li, Y

1997-12-01

This paper introduces a method to determine the volume activity concentration of alpha and/or beta artificial radionuclides in the environment and radon/thoron progeny background-compensation based on a Si surface-barrier detector. By measuring the alpha peak counts of 218Po and 214Po in two time intervals, the activity concentration of 218Po, 214Pb and 214Bi aerosol particles were determined; meanwhile, the total beta count of 214Pb and 214Bi aerosols was also calculated from their decay scheme. With the average equilibrium factor of thoron progeny in general environment, the alpha and beta counts of thoron progeny were approximately evaluated by 212Po alpha peak counts. The alpha count of transuranic aerosols was determined by subtracting the trail counts of radon/thoron progeny alpha peaks. The total count of beta artificial radionuclides was determined by subtracting the beta counts of radon/thoron progeny aerosol particles. In our preliminary experiments, if the radon progeny concentration is less than 15 Bq m(-3), the lower limit of detection of transuranics concentration is less than 0.1 Bq m(-3). Even if the radon progeny concentration is as high as 75 Bq m(-3), the lower limit of detection of total beta activity concentration of artificial nuclides aerosols is less than 1 Bq m(-3).

The weathering of organic carbon and pyrite sulfur in Earth's crust and its importance for regulating atmospheric composition, seawater chemistry, and stable isotope records

NASA Astrophysics Data System (ADS)

Reinhard, C. T.; Planavsky, N.; Bolton, E. W.

2016-12-01

Earth's crust stores extremely large reservoirs of organic carbon and pyrite sulfur, and transient or secular changes in the sizes of these reservoirs have the capacity to dramatically alter atmospheric composition, climate, seawater acid-base chemistry, and the propagation of isotopic signals into the geologic record. This talk will present and discuss new quantitative approaches toward better understanding the factors that control organic carbon and pyrite sulfur weathering under a wide range of Earth surface conditions, as well as their downstream effects on seawater chemistry, stability of atmospheric pO2, and conventional interpretations of stable carbon isotope mass balance during pivotal events in Earth's biogeochemical evolution. In particular, we will focus on (1) development of a weathering-driven scaling between atmospheric pO2 and geologic carbon isotope signals that explains the relative stability of marine δ13C through time and provides a mechanism for protracted negative δ13C excursions during transient increases in atmospheric pO2; (2) experimental and theoretical approaches aimed at better understanding the role of pyrite sulfur weathering in stabilizing atmospheric pO2; and (3) the importance of redox balance in the sedimentary rock cycle for controlling the marine carbonate system and atmospheric pCO2.

Preparation and surface characterization of activated carbons from Euphorbia rigida by chemical activation with ZnCl2, K2CO3, NaOH and H3PO4

NASA Astrophysics Data System (ADS)

Kılıç, Murat; Apaydın-Varol, Esin; Pütün, Ayşe Eren

2012-11-01

Preparation of activated carbons from Euphorbia rigida by chemical activation with different impregnation agents and ratios was studied. ZnCl2, K2CO3, NaOH and H3PO4 were used as chemical activation agents and four impregnation ratios (25-50-75-100%) by mass were applied on biomass. Activation is applied to impregnated biomass samples at 700 °C under sweeping gas in a fixed bed reactor. For determination of chemical and physical properties of the obtained activated carbons; elemental analysis was applied to determine the elemental composition (C, H, N, O) and FT-IR spectra was used to analyze the functional groups. BET equation was used to calculate the surface areas of activated carbons. For understanding the changes in the surface structure, activated carbons were conducted to Scanning Electron Microscopy (SEM). Maximum BET surface area (2613 m2/g) was reached with 75% K2CO3 impregnated biomass sample. Experimental results showed that impregnation types and ratios have a significant effect on the pore structure of activated carbon and E. rigida seems to be an alternative precursor for commercial activated carbon production.

Geochemical Composition of Surface Water in the Mineralized Lom Basin, East Cameroon: Natural and Anthropogenic Sources.

NASA Astrophysics Data System (ADS)

Mimba, M. E.; Ohba, T.; Nguemhe Fils, S. C.; Wirmvem, M. J.

2016-12-01

Thousands of people in East Cameroon depend on surface water for consumption and domestic purposes. The Lom basin, north of the region, is heavily mineralized especially in gold owing to its regional geological setting. Although research has been done regarding the rock type, age, formation history and reconnaissance gold surveys, surface water investigation in the area has received limited attention. Thus, this study appraises the first regional hydrogeochemical program for environmental assessment of the mineralized Lom basin. Fifty-two representative stream water samples were collected under base flow conditions and analysed for major cations (Ca2+, Mg2+, Na+, K+ ), major anions (HCO3-, F-, Cl-, NO2-, NO3-, Br-, PO43-, SO42- ) and stable isotopes (δD and δ18O). Calcium and HCO3- were the dominant ions. The chemical facies were CaHCO3 and NaHCO3 indicating surface water draining igneous/metamorphic rocks in hot and humid equatorial climate, resulting in the discordant dissolution of primary silicate minerals. From the isotopic evaluation, the stream water is of meteoric origin, shows negligible evaporation effect and has a common recharge source. The major ion geochemistry demonstrated the potential to discriminate between natural and anthropogenic origins. Distribution trends of Ca2+, Mg2+, Na+, K+, HCO3- and SO42- showed a correlation with the lithology and the occurrence of sulphide minerals associated with hydrothermal gold mineralization in the area. The distribution patterns of NO3- and Cl- reflect pollution from settlement. Overall, the chemistry of stream water in the Lom basin is mainly controlled by rock weathering compared to anthropogenic influence. Surface water quality is easily influenced by anthropogenic activities, and stream sediment collects effectively trace metals resulting from such activities. Hence, geochemical mapping incorporating stream water and stream sediment is of considerable value in future investigations within the Lom basin.

Concentration of selected trace elements and PCBs in sediments from the Adriatic Sea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fowler, S W; Hamilton, T F; Coquery, M

2000-07-26

A broad baseline study of the levels and distributions of trace metals and PCB compounds in sediments has been undertaken. PCB concentrations in surface sediments reflect the source of these contaminates in the region. The highest PCB concentrations as Aroclor 1260 (approximately 10 ng g{sup -1}) were found in sediments near the outflow of the Po river. The lowest concentrations (1.5 ng g{sup -1} dry) were associated with the sediments from the Jabuka Pit in the Middle Adriatic. These values are quite similar to total PCBs (<1.0-17) measured in surface sediments sampled off the coast of Croatia in 1977-78. Thus,more » based on the limited amount of new data available, it appears that there has been little, if any, decrease in PCB loading in Adriatic sediments over the past 15 years. Downcore profiles of PCBs in sediment cores are also discussed from a pollution history standpoint. Likewise, total mercury in surface sediments was also highest at stations off the Po (403-499 ng g{sup -1} dry) and lowest (67-224 ng g{sup -1}) in the Jabuka Pit. In one core located just south of the Po outflow, total Hg concentrations at all depths were relatively high decreasing gradually from approximately 400 ng g{sup -1} in the top 4 cm to roughly 200 ng g{sup -1} at a depth of 32 cm. Using a {sup 210}Pb-derived sedimentation rate of 0.26 em Y{sup -1} for this station, it appears that anthropogenic inputs of mercury may have been responsible for the gradual increase in total mercury noted over the last 125 years.« less

Characteristics and Distribution of Phosphorus in Surface Sediments of Limnetic Ecosystem in Eastern China

PubMed Central

Zhang, Wenqiang; Jin, Xin; Zhu, Xiaolei; Shan, Baoqing

2016-01-01

Phosphorus (P) is an essential nutrient for aquatic organisms; however, excessive P inflow to limnetic ecosystems can induce eutrophication. P concentrations in the rivers, wetlands and lakes of Eastern China have been amplified by fertilizer and sewage inputs associated with the development of industry and agriculture. Yet, knowledge of the distribution and speciation of P is lacking at the regional scale. We determined the distribution and speciation of P in limnetic ecosystems in Eastern China using Standards, Measurements and Testing (SMT) and phosphorus nuclear magnetic resonance (31P-NMR). The results indicate that P pollution in surface sediments was serious. Inorganic P (Pi) was the primary drive of variation in total P (TP) among different river systems, and Pi accounted for 71% to 90% of TP in surface sediment in Eastern China. Also, the concentrations of TP and Pi varied among watersheds and Pi primarily drove the variation in TP in different watersheds. Sediments less than 10-cm deep served as the main P reservoir. Environmental factors affect the speciation and origin of P. NaOH-Pi, HCl-Pi and organic P (Po) were related to pH accordingly at the regional scale. The physicochemical properties of sediments from different limnetic ecosystems affect the P speciation. HCl-Pi was higher in wetland sediments than in riverine and lake sediments in Eastern China. Conversely, NaOH-Pi was lowest in wetland sediments. Total Po concentration was lower in riverine sediments than in other sediments, but Mono-P was higher, with an average concentration of 48 mg kg−1. Diesters-P was highest in lake sediments. By revealing the regional distribution of TP, Pi and Po, this study will support eutrophication management in Eastern China. PMID:27281191

Pollutant sources in an arsenic-affected multilayer aquifer in the Po Plain of Italy: Implications for drinking-water supply.

PubMed

Rotiroti, Marco; McArthur, John; Fumagalli, Letizia; Stefania, Gennaro A; Sacchi, Elisa; Bonomi, Tullia

2017-02-01

In aquifers 160 to 260m deep that used for public water-supply in an area ~150km 2 around the town of Cremona, in the Po Plain of Northern Italy, concentrations of arsenic (As) are increasing with time in some wells. The increase is due to drawdown of As-polluted groundwater (As ≤144μg/L) from overlying aquifers at depths 65 to 150m deep in response to large-scale abstraction for public supply. The increase in As threatens drinking-water quality locally, and by inference does so across the entire Po Plain, where natural As-pollution of groundwater (As >10μg/L) is a basin-wide problem. Using new and legacy data for Cl/Br, δ 18 O/δ 2 H and other hydrochemical parameters with groundwater from 32 wells, 9 surface waters, a sewage outfall and rainwater, we show that the deep aquifer (160-260m below ground level), which is tapped widely for public water-supply, is partly recharged by seepage from overlying aquifers (65-150m below ground level). Groundwater quality in deep aquifers appears free of anthropogenic influences and typically <10μg/L of As. In contrast, shallow groundwater and surface water in some, not all, areas are affected by anthropogenic contamination and natural As-pollution (As >10μg/L). Outfalls from sewage-treatment plants and black water from septic tanks firstly affect surface waters, which then locally infiltrate shallow aquifers under high channel-stages. Wastewater permeating shallow aquifers carries with it NO 3 and SO 4 which suppress reduction of iron oxyhydroxides in the aquifer sediments and so suppress the natural release of As to groundwater. Copyright © 2016 Elsevier B.V. All rights reserved.

Linkage between global sea surface temperature and hydroclimatology of a major river basin of India before and after 1980

NASA Astrophysics Data System (ADS)

Pattanayak, Sonali; Nanjundiah, Ravi S.; Nagesh Kumar, D.

2017-12-01

The frequent occurrence of flood and drought worldwide has drawn attention to assessing whether the hydroclimatology of major river basins has changed. The Mahanadi river basin (MRB) is the major source of fresh water for both Chattisgarh and Odisha states (71 million people approximately) in India. The MRB (141 600 km2 area) is one of the most vulnerable to climate change and variations in temperature and precipitation. In recent years, it has repeatedly faced adverse hydrometeorological conditions. Large-scale ocean-atmospheric phenomena have a substantial influence on river hydroclimatology. Hence global sea surface temperature (SST) linkage with the precipitation and surface temperature of the MRB was analyzed over the period 1950-2012. Significant changes in seasonal correlation patterns were witnessed from 1950-1980 (PR-80) to 1981-2012 (PO-80). The correlation was higher during PR-80 compared to PO-80 between the El Niño region SST versus the maximum temperature (T max) in all seasons except the pre-monsoon season and the minimum temperature (T min) in all seasons except the monsoon season. However, precipitation correlation changes are not prominent. Like the SST, the correlation patterns of sea level pressure with precipitation, T max and T min shifted conspicuously from PR-80 to PO-80. These shifts could be related to change in Pacific decadal SST patterns and anthropogenic effects. Fingerprint-based detection and attribution analysis revealed that the observed changes in T min (pre-monsoon and monsoon season) during the second half of the 20th century cannot be explained solely by natural variability and can be attributed to an anthropogenic effect.

A simple, sensitive and non-destructive technique for characterizing bovine dental enamel erosion: attenuated total reflection Fourier transform infrared spectroscopy

PubMed Central

Kim, In-Hye; Son, Jun Sik; Min, Bong Ki; Kim, Young Kyoung; Kim, Kyo-Han; Kwon, Tae-Yub

2016-01-01

Although many techniques are available to assess enamel erosion in vitro, a simple, non-destructive method with sufficient sensitivity for quantifying dental erosion is required. This study characterized the bovine dental enamel erosion induced by various acidic beverages in vitro using attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Deionized water (control) and 10 acidic beverages were selected to study erosion, and the pH and neutralizable acidity were measured. Bovine anterior teeth (110) were polished with up to 1 200-grit silicon carbide paper to produce flat enamel surfaces, which were then immersed in 20 mL of the beverages for 30 min at 37 °C. The degree of erosion was evaluated using ATR-FTIR spectroscopy and Vickers' microhardness measurements. The spectra obtained were interpreted in two ways that focused on the ν1, ν3 phosphate contour: the ratio of the height amplitude of ν3 PO4 to that of ν1 PO4 (Method 1) and the shift of the ν3 PO4 peak to a higher wavenumber (Method 2). The percentage changes in microhardness after the erosion treatments were primarily affected by the pH of the immersion media. Regression analyses revealed highly significant correlations between the surface hardness change and the degree of erosion, as detected by ATR-FTIR spectroscopy (P<0.001). Method 1 was the most sensitive to these changes, followed by surface hardness change measurements and Method 2. This study suggests that ATR-FTIR spectroscopy is potentially advantageous over the microhardness test as a simple, non-destructive, sensitive technique for the quantification of enamel erosion. PMID:27025266

A simple, sensitive and non-destructive technique for characterizing bovine dental enamel erosion: attenuated total reflection Fourier transform infrared spectroscopy.

PubMed

Kim, In-Hye; Son, Jun Sik; Min, Bong Ki; Kim, Young Kyoung; Kim, Kyo-Han; Kwon, Tae-Yub

2016-03-30

Although many techniques are available to assess enamel erosion in vitro, a simple, non-destructive method with sufficient sensitivity for quantifying dental erosion is required. This study characterized the bovine dental enamel erosion induced by various acidic beverages in vitro using attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Deionized water (control) and 10 acidic beverages were selected to study erosion, and the pH and neutralizable acidity were measured. Bovine anterior teeth (110) were polished with up to 1 200-grit silicon carbide paper to produce flat enamel surfaces, which were then immersed in 20 mL of the beverages for 30 min at 37 °C. The degree of erosion was evaluated using ATR-FTIR spectroscopy and Vickers' microhardness measurements. The spectra obtained were interpreted in two ways that focused on the ν1, ν3 phosphate contour: the ratio of the height amplitude of ν3 PO4 to that of ν1 PO4 (Method 1) and the shift of the ν3 PO4 peak to a higher wavenumber (Method 2). The percentage changes in microhardness after the erosion treatments were primarily affected by the pH of the immersion media. Regression analyses revealed highly significant correlations between the surface hardness change and the degree of erosion, as detected by ATR-FTIR spectroscopy (P<0.001). Method 1 was the most sensitive to these changes, followed by surface hardness change measurements and Method 2. This study suggests that ATR-FTIR spectroscopy is potentially advantageous over the microhardness test as a simple, non-destructive, sensitive technique for the quantification of enamel erosion.

Deterioration of Cortical Bone Microarchitecture: Critical Component of Renal Osteodystrophy Evaluation.

PubMed

Sharma, Ashish K; Toussaint, Nigel D; Masterson, Rosemary; Holt, Stephen G; Rajapakse, Chamith S; Ebeling, Peter R; Mohanty, Sindhu T; Baldock, Paul; Elder, Grahame J

2018-05-23

Cortical bone is a significant determinant of bone strength and its deterioration contributes to bone fragility. Thin cortices and increased cortical porosity have been noted in patients with chronic kidney disease (CKD), but the "Turnover Mineralization Volume" classification of renal osteodystrophy does not emphasize cortical bone as a key parameter. We aimed to assess trabecular and cortical bone microarchitecture by histomorphometry and micro-CT in patients with CKD G5 and 5D (dialysis). Transiliac bone biopsies were performed in 14 patients undergoing kidney transplantation (n = 12) and parathyroidectomy (n = 2). Structural parameters were analysed by histomorphometry and micro-CT including trabecular bone volume, thickness (TbTh), number (TbN) and separation and cortical thickness (CtTh) and porosity (CtPo). Indices of bone remodelling and mineralisation were obtained and relationships to bone biomarkers examined. Associations were determined by Spearman's or Pearson's rank correlation coefficients. By micro-CT, trabecular parameters were within normal ranges in most patients, but all patients showed very low CtTh (127 ± 44 µm) and high CtPo (60.3 ± 22.5%). CtPo was inversely related to TbN (r = -0.56; p = 0.03) by micro-CT and to TbTh (r = -0.60; p = 0.024) by histomorphometry and correlated to parathyroid hormone values (r = 0.62; p = 0.021). By histomorphometry, bone turnover was high in 50%, low in 21% and normal in 29%, while 36% showed abnormal patterns of mineralization. Significant positive associations were observed between osteoblast surface, osteoclast surface, mineralization surface and bone turnover markers. Deterioration of cortical -microarchitecture despite predominantly normal trabecular parameters reinforces the importance of comprehensive cortical evaluation in patients with CKD. © 2018 S. Karger AG, Basel.

Surface drifter derived circulation in the northern and middle Adriatic Sea: Response to wind regime and season

USGS Publications Warehouse

Ursella, L.; Poulain, P.-M.; Signell, R.P.

2007-01-01

More than 120 satellite-tracked drifters were deployed in the northern and middle Adriatic (NMA) Sea between September 2002 and November 2003, with the purpose of studying the surface circulation at mesoscale to seasonal scale in relation to wind forcing, river runoff, and bottom topography. Pseudo-Eulerian and Lagrangian statistics were calculated from the low-pass-filtered drifter velocity data between September 2002 and December 2003. The structure of the mean circulation is determined with unprecedented high horizontal resolution by the new data. In particular, mean currents, velocity variance, and kinetic energy levels are shown to be maximal in the Western Adriatic Current (WAC). Separating data into seasons, we found that the mean kinetic energy is maximal in fall, with high values also in winter, while it is significantly weaker in summer. High-resolution Local Area Model Italy winds were used to relate the drifter velocities to the wind fields. The surface currents appear to be significantly influenced by the winds. The mean flow during the northeasterly bora regime shows an intensification of the across-basin recirculating currents. In addition, the WAC is strongly intensified both in intensity and in its offshore lateral extension. In the southeasterly sirocco regime, northward flow without recirculation dominates in the eastern half of the basin, while during northwesterly maestro the WAC is enhanced. Separating the data into low and high Po River discharge rates for low-wind conditions shows that the WAC and the velocity fluctuations in front of the Po delta are stronger for high Po River runoff. Lagrangian covariance, diffusivity, and integral time and space scales are larger in the along-basin direction and are maximal in the southern portion of the WAC. Copyright 2006 by the American Geophysical Union.

Adsorption isotope effects of water on mesoporous silica and alumina with implications for the land-vegetation-atmosphere system

NASA Astrophysics Data System (ADS)

Lin, Ying; Horita, Juske; Abe, Osamu

2018-02-01

Soil water dynamics within a vadose (unsaturated) zone is a key component in the hydrologic cycle, especially in arid regions. In applying the Craig-Gordon evaporation model to obtain isotopic compositions of soil water and the evaporated vapor in land-surface models (LSMs), it has been assumed that the equilibrium isotope fractionation factors between soil water and water vapor, α(2H) and α(18O), are identical to those between liquid and vapor of bulk water. Isotope effects in water condensation arise from intermolecular hydrogen bonding in the condensed phase and the appearance of hindered rotation/translation. Hydrogen bonding between water molecules and pore surface hydroxyl groups influences adsorption isotope effects. To test whether equilibrium fractionation factors between soil water and water vapor are identical to those between liquid and vapor of bulk water and to evaluate the influence of pore size and chemical composition upon adsorption isotope effects, we extended our previous experiments of a mesoporous silica (15 nm) to two other mesoporous materials, a silica (6 nm) and an alumina (5.8 nm). Our results demonstrated that α(2H) and α(18O) between adsorbed water and water vapor are 1.057 and 1.0086 for silica (6 nm) and 1.041 and 1.0063 for alumina (5.8 nm), respectively, at saturation pressure (po), which are smaller than 1.075 and 1.0089, respectively, between liquid and vapor phases of free water at 30 °C and that the differences exaggerate at low water contents. However, the profiles of α values with relative pressures (p/po) for these three materials differ due to the differences in chemical compositions and pore sizes. Empirical formula relating α(2H) and α(18O) values to the proportions of filled pores (f) are developed for potential applications to natural soils. Our results from triple oxygen isotope analyses demonstrated that the isotope fractionation does not follow a canonical law. For the silica (15 nm), fractionation exponents (17θ) are 0.5361 ± 0.0018 and 0.5389 ± 0.0016 at p/po = 0.72 and 0.77, respectively. For the silica (6 nm), 17θ values are 0.5330 ± 0.0011 at p/po = 0.65 and 0.5278 ± 0.0010 at p/po = 0.81. For the alumina (5.8 nm), 17θ value is 0.5316 ± 0.0015 at p/po = 0.78. These values are greater than or equal to that of liquid-vapor equilibrium of bulk water (0.529 ± 0.001).

SERS Technique for Rapid Bacterial Screening

USDA-ARS?s Scientific Manuscript database

This study reports the feasibility of citrate-reduced colloidal silver SERS for differentiating E. coli, Listeria, and Salmonella. FT-Raman and SERS spectra of both silver colloids and colloid-K3PO4 mixtures were collected and analyzed to evaluate the reproducibility and stability of silver colloids...

75 FR 6350 - Post Allowance and Refiling

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-09

... DEPARTMENT OF COMMERCE Patent and Trademark Office Post Allowance and Refiling ACTION: Proposed collection; comment request. SUMMARY: The United States Patent and Trademark Office (USPTO), as part of its... Officer, Office of the Chief Information Officer, United States Patent and Trademark Office, P.O. Box 1450...

Phosphorus transport and retention in a channel draining an urban, tropical catchment with informal settlements

NASA Astrophysics Data System (ADS)

Nyenje, P. M.; Meijer, L. M. G.; Foppen, J. W.; Kulabako, R.; Uhlenbrook, S.

2014-03-01

Urban catchments in sub-Saharan Africa (SSA) are increasingly becoming a major source of phosphorus (P) to downstream ecosystems. This is primarily due to large inputs of untreated wastewater to urban drainage channels, especially in informal settlements (or slums). However, the processes governing the fate of P in these catchments are largely unknown. In this study, these processes are investigated. During high runoff events and a period of base flow, we collected hourly water samples (over 24 h) from a primary channel draining a 28 km2 slum-dominated catchment in Kampala, Uganda, and from a tertiary channel draining one of the contributing slum areas (0.54 km2). The samples were analysed for orthophosphate (PO4-P), particulate P (PP), total P (TP), suspended solids (SS) and hydrochemistry. We also collected channel bed and suspended sediments to determine their geo-available metals, sorption characteristics and the dominant phosphorus forms. Our results showed that the catchment exported high fluxes of P (0.3 kg km2 d-1 for PO4-P and 0.95 for TP), which were several orders of magnitude higher than values normally reported in literature. A large proportion of P exported was particulate (56% of TP) and we inferred that most of it was retained along the channel bed. The retained sediment P was predominantly inorganic (> 63% of total sediment P) and consisted of mostly Ca and Fe-bound P, which were present in almost equal proportions. Ca-bound sediment P was attributed to the adsorption of P to calcite because surface water was near saturation with respect to calcite in all the events sampled. Fe-bound sediment P was attributed to the adsorption of P to iron oxides in suspended sediment during runoff events given that surface water was undersaturated with respect to iron phosphates. We also found that the bed sediments were P-saturated and showed a tendency to release P by mineralisation and desorption. During rain events, there was a flushing of PP which we attributed to the resuspension of P-rich bed sediment that accumulated in the channel during low flows. However, first-flush effects were not observed. Our findings provide useful insights into the processes governing the fate and transport of P in urban slum catchments in SSA.