Comparative evaluation of power factor impovement techniques for squirrel cage induction motors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spee, R.; Wallace, A.K.

1992-04-01

This paper describes the results obtained from a series of tests of relatively simple methods of improving the power factor of squirrel-cage induction motors. The methods, which are evaluated under controlled laboratory conditions for a 10-hp, high-efficiency motor, include terminal voltage reduction; terminal static capacitors; and a floating'' winding with static capacitors. The test results are compared with equivalent circuit model predictions that are then used to identify optimum conditions for each of the power factor improvement techniques compared with the basic induction motor. Finally, the relative economic value, and the implications of component failures, of the three methods aremore » discussed.« less

FUZZY LOGIC BASED INTELLIGENT CONTROL OF A VARIABLE SPEED CAGE MACHINE WIND GENERATION SYSTEM

EPA Science Inventory

The paper describes a variable-speed wind generation system where fuzzy logic principles are used to optimize efficiency and enhance performance control. A squirrel cage induction generator feeds the power to a double-sided pulse width modulated converter system which either pump...

FUZZY LOGIC BASED INTELLIGENT CONTROL OF A VARIABLE SPEED CAGE MACHINE WIND GENERATION SYSTEM

EPA Science Inventory

The report gives results of a demonstration of the successful application of fuzzy logic to enhance the performance and control of a variable-speed wind generation system. A squirrel cage induction generator feeds the power to either a double-sided pulse-width modulation converte...

Static air-gap eccentricity fault diagnosis using rotor slot harmonics in line neutral voltage of three-phase squirrel cage induction motor

NASA Astrophysics Data System (ADS)

Oumaamar, Mohamed El Kamel; Maouche, Yassine; Boucherma, Mohamed; Khezzar, Abdelmalek

2017-02-01

The mixed eccentricity fault detection in a squirrel cage induction motor has been thoroughly investigated. However, a few papers have been related to pure static eccentricity fault and the authors focused on the RSH harmonics presented in stator current. The main objective of this paper is to present an alternative method based on the analysis of line neutral voltage taking place between the supply and the stator neutrals in order to detect air-gap static eccentricity, and to highlight the classification of all RSH harmonics in line neutral voltage. The model of squirrel cage induction machine relies on the rotor geometry and winding layout. Such developed model is used to analyze the impact of the pure static air-gap eccentricity by predicting the related frequencies in the line neutral voltage spectrum. The results show that the line neutral voltage spectrum are more sensitive to the air-gap static eccentricity fault compared to stator current one. The theoretical analysis and simulated results are confirmed by experiments.

A caged Ab reveals an immediate/instructive effect of BDNF during hippocampal synaptic potentiation

PubMed Central

Kossel, Albrecht H.; Cambridge, Sidney B.; Wagner, Uta; Bonhoeffer, Tobias

2001-01-01

Neurotrophins have been shown to be involved in functional strengthening of central nervous system synapses. Although their general importance in this process is undisputed, it remains unresolved whether neurotrophins are truly mediators of synaptic strengthening or merely important cofactors. To address this question, we have devised a method to inactivate endogenous brain-derived neurotrophic factor (BDNF) with high time resolution by “caging” a function-blocking mAb against BDNF with a photosensitive protecting compound. Different assays were used to show that this inactivation of the Ab is reversible by UV light. Synaptic potentiation after τ-burst stimulation in the CA1 region of acute hippocampal slices was significantly less when applying the unmodified Ab compared with the caged Ab. Importantly, photoactivation of the caged Ab during the time of induction of synaptic enhancement led to a marked decrease in potentiation. Our experiments therefore strengthen the view that endogenous BDNF has fast effects during induction of synaptic plasticity. The results additionally show that caged Abs can provide a tool for precise spatiotemporal control over endogenous protein levels. PMID:11724927

The analysis of 3-phase squirrel-cage induction motors including space harmonics and mutual slotting in transient and steady state

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paap, G.C.

1991-03-01

From general equations which describe the transient electromechanical behavior of the asynchronous squirrel-cage motor, and which include the influence of space harmonics and mutual slotting, simplified models are derived and compared. The models derived are demonstrated in examples where special attention is paid to the influence of the place of the harmonics in the mutual inductance matrix and the influence of mutual slotting. Further, the steady-state equations are derived and the back-transformation for the stator and rotor currents is given. One example is compared with the result of measurements.

An inductively powered telemetry system for temperature, EKG, and activity monitoring

NASA Technical Reports Server (NTRS)

Fryer, T. B.; Lund, G. F.; Williams, B. A.

1978-01-01

An implant telemetry system for the simultaneous monitoring of temperature, activity, and EKG from small animals, such as rats, was designed with the feature that instead of a battery the system is energized by an inductive field. A 250 kHz resonant coil surrounds the cage (30 x 30 x 20 cm) and provides the approximately 100 microns of power required to operate the implant transmitter while allowing the animal unrestrained movement in the cage. The implant can also be battery operated if desired. RF transmission is in the 8-10 MHz band, which allows the use of a simple, essentially single IC chip, receiver.

An inductively powered telemetry system for temperature, EKG, and activity monitoring

NASA Technical Reports Server (NTRS)

Fryer, T. B.; Lund, G. F.; Williams, B. A.

1978-01-01

An implant telemetry system for the simultaneous monitoring of temperature, activity, and EKG from small animals, such as rats, has recently been designed with the novel feature that instead of a battery the system is energized by an inductive field. A 250 kHz resonant coil surrounds the cage (30 x 30 x 20 cm) and provides the approximately 100 microwatt of power required to operate the implant transmitter while allowing the animal unrestrained movement in the cage. The implant can also be battery operated if desired. RF transmission is in the 8-10 MHz band, which allows the use of a simple, essentially single IC chip, receiver.

An SCR inverter for electric vehicles

NASA Technical Reports Server (NTRS)

Latos, T.; Bosack, D.; Ehrlich, R.; Jahns, T.; Mezera, J.; Thimmesch, D.

1980-01-01

An inverter for an electric vehicle propulsion application has been designed and constructed to excite a polyphase induction motor from a fixed propulsion battery source. The inverter, rated at 35kW peak power, is fully regenerative and permits vehicle operation in both the forward and reverse directions. Thyristors are employed as the power switching devices arranged in a dc bus commutated topology. This paper describes the major role the controller plays in generating the motor excitation voltage and frequency to deliver performance similar to dc systems. Motoring efficiency test data for the controller are presented. It is concluded that an SCR inverter in conjunction with an ac induction motor is a viable alternative to present dc vehicle propulsion systems on the basis of performance and size criteria.

The operation of a single-sided linear induction motor with squirrel-cage and solid-steel reaction rails

NASA Astrophysics Data System (ADS)

Eastham, A. R.; Katz, R. M.

1980-09-01

Two test programs have been conducted to evaluate the performance of a single-sided linear induction motor with a squirrel-cage reaction rail and with a solid steel reaction rail. A 1.73-m-long six-pole stator interacted with the rails mounted on the rim of a 7.6-m-diam wheel. A 64-channel data acquisition system allowed tests to be performed over a wide range of operating conditions at speeds up to 20 m/sec. Typical test results which compare and contrast the mechanical, electrical and magnetic behavior of the SLIMs are presented. The test data are being used to assess the SLIM as an integrated suspension/propulsion system and for other transportation applications.

The Design and its Verification of the Double Rotor Double Cage Induction Motor

NASA Astrophysics Data System (ADS)

Sinha, Sumita; Deb, Nirmal K.; Biswas, Sujit K.

2017-02-01

The concept of a double rotor motor presented earlier and its equivalent circuit has been developed, showing a non-linear parameter content. The two rotors (which are recommended to be double cage type for development of high starting torque) can run with equal or unequal speed independently, depending on their individual loading. This paper presents the elaborate design procedure, step-by-step, for the double rotor double cage motor and verifies the designed data with that obtained from three separate tests (compared to two for conventional motor) on a prototype, such that optimum performance can be obtained from the motor.

Real-Time, Polyphase-FFT, 640-MHz Spectrum Analyzer

NASA Technical Reports Server (NTRS)

Zimmerman, George A.; Garyantes, Michael F.; Grimm, Michael J.; Charny, Bentsian; Brown, Randy D.; Wilck, Helmut C.

1994-01-01

Real-time polyphase-fast-Fourier-transform, polyphase-FFT, spectrum analyzer designed to aid in detection of multigigahertz radio signals in two 320-MHz-wide polarization channels. Spectrum analyzer divides total spectrum of 640 MHz into 33,554,432 frequency channels of about 20 Hz each. Size and cost of polyphase-coefficient memory substantially reduced and much of processing loss of windowed FFTs eliminated.

On-line diagnosis of defaults on squirrel cage motors using FEM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bentounsi, A.; Nicolas, A.

1998-09-01

In industry, the predictive maintenance has become a strategic concept. Economic interest of on-line diagnosis of faults in electric machines gave rise to various researches in that field. This paper proposes a local approach to tackle the problem of breaking bars and end-rings of squirrel cage in induction machines based mainly on the signature of the local variables, such as the normal flux density. This allows a finer analysis, by use of a finite element based simulation.

[Impact of OSA Therapy on Established Polyphasic Sleep].

PubMed

Kerl, J; Dellweg, D

2018-05-23

 The prevalence of polyphasic sleep (PS) in patients with sleep apnoea (OSA) is investigated in this study. In established PS the possible impact of OSA therapy on sleep behaviour was examined.  Sleep patterns in 24 hours of initial recepted OSA patients were recorded by questionnaire (n = 163). In polyphasic sleepers the sleep patterns were reevaluated after OSA therapy initiation. In additional patients polyphasic therapy usage was investigated by telemonitoring data (n = 487). 39,6 % of the patients had PS. After OSA therapy initiation in 97,0 % of the polyphasic sleepers a monophasic device usage was established while 3,0 % had a polyphasic usage. PS was switched to monophasic sleep in 81,8 % of the patients. 15.2 % had preserved PS without device usage on daytimes. 2,9 % of the telemonitoring patients showed a polyphasic usage pattern. The prevalence of PS in OSA patients is higher than in the general population. PS is converted to monophasic sleep in 81,8 % after OSA therapy initiation. In preserved PS the majority of patients doesn't use the therapy while napping. Polyphasic device usage was 2,9 % in telemonitoring patients and 3,0 % of the controls of this study. © Georg Thieme Verlag KG Stuttgart · New York.

API 541 Third Edition, a revised and improved purchasing specification for form wound squirrel cage induction motors -- 250 horsepower and larger

DOE Office of Scientific and Technical Information (OSTI.GOV)

Donner, G.; Subler, W.

1995-12-31

API 541 Third Edition is a standard that covers the minimum requirements for all form wound squirrel cage induction motors above NEMA 440 frame sizes (normally 250 HP and above). The standard is intended to be used to describe motors that will be used by the petroleum industry. The purpose of API 541 is to serve as a comprehensive standard which can be used by specifiers of high performance motors. Users no longer have to prepare their own purchase specifications, and manufacturers can produce a standard motor that will be widely accepted and competitively priced. The API 541 Standard ismore » revised on a 5 year cycle to insure that it is always timely and reflects the latest technology.« less

Polyphase-discrete Fourier transform spectrum analysis for the Search for Extraterrestrial Intelligence sky survey

NASA Technical Reports Server (NTRS)

Zimmerman, G. A.; Gulkis, S.

1991-01-01

The sensitivity of a matched filter-detection system to a finite-duration continuous wave (CW) tone is compared with the sensitivities of a windowed discrete Fourier transform (DFT) system and an ideal bandpass filter-bank system. These comparisons are made in the context of the NASA Search for Extraterrestrial Intelligence (SETI) microwave observing project (MOP) sky survey. A review of the theory of polyphase-DFT filter banks and its relationship to the well-known windowed-DFT process is presented. The polyphase-DFT system approximates the ideal bandpass filter bank by using as few as eight filter taps per polyphase branch. An improvement in sensitivity of approx. 3 dB over a windowed-DFT system can be obtained by using the polyphase-DFT approach. Sidelobe rejection of the polyphase-DFT system is vastly superior to the windowed-DFT system, thereby improving its performance in the presence of radio frequency interference (RFI).

Investigation of self-excited induction generators for wind turbine applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muljadi, E.; Butterfield, C.P.; Sallan, J.

2000-02-28

The use of squirrel-cage induction machines in wind generation is widely accepted as a generator of choice. The squirrel-cage induction machine is simple, reliable, cheap, lightweight, and requires very little maintenance. Generally, the induction generator is connected to the utility at constant frequency. With a constant frequency operation, the induction generator operates at practically constant speed (small range of slip). The wind turbine operates in optimum efficiency only within a small range of wind speed variation. The variable-speed operation allows an increase in energy captured and reduces both the torque peaks in the drive train and the power fluctuations sentmore » to the utility. In variable-speed operation, an induction generator needs an interface to convert the variable frequency output of the generator to the fixed frequency at the utility. This interface can be simplified by using a self-excited generator because a simple diode bridge is required to perform the ac/dc conversion. The subsequent dc/ac conversion can be performed using different techniques. The use of a thyristor bridge is readily available for large power conversion and has a lower cost and higher reliability. The firing angle of the inverter bridge can be controlled to track the optimum power curve of the wind turbine. With only diodes and thyristors used in power conversion, the system can be scaled up to a very high voltage and high power applications. This paper analyzes the operation of such a system applied to a 1/3-hp self-excited induction generator. It includes the simulations and tests performed for the different excitation configurations.« less

Induction of c-Fos, Zif268, and Arc from acute bouts of voluntary wheel running in new and pre-existing adult mouse hippocampal granule neurons

PubMed Central

Clark, Peter J.; Bhattacharya, Tushar K.; Miller, Daniel S.; Rhodes, Justin S.

2011-01-01

The functional significance of newly formed granule neurons in the adult mammalian hippocampus remains a mystery. Recently, it was demonstrated that wheel running increases new neuron survival and c-Fos expression in new and pre-existing granule cells in an activity-dependent manner. It is currently unknown whether other immediate early genes (IEGs) become expressed in granule neurons from running. Further, it is unknown whether locomotor activity in home cages without wheels can influence neurogenesis and IEG expression similar to running. The purpose of this study was three fold: 1) to determine if Arc and Zif268 expression are also induced from wheel running in both pre-existing and newly formed neurons 2) to determine if neurogenesis and IEG induction is related to horizontal distance traveled in home cages without wheels and 3) to determine whether IEG induction is related to acute bouts of running or chronic effects. Adult C57BL/6J female mice were placed in cages with or without running wheels for 31 days. The first 10 days, mice received daily injections of 5-Bromo-2′-deoxyuridine (BrdU) to label dividing cells. On day 31, running and non-running animals were euthanized either 2 hours after peak activity, or during a period of relative inactivity. Immunohistochemistry was performed on hippocampal sections with antibodies against BrdU, mature neuron marker NeuN, c-Fos, Arc, and Zif268. Results demonstrate that Arc, Zif268, and c-Fos are induced from wheel running but not movement in cages without wheels. All IEGs were expressed in new neurons from running. Further, IEGs were induced acutely by running, as increased expression did not continue into the light cycle, a period of relative inactivity. The results suggest that robust movements, like running, are necessary to stimulate IEG expression and neurogenesis. Moreover, results suggest new neurons from running may be processing information about running behavior itself. PMID:21497182

A 640-MHz 32-megachannel real-time polyphase-FFT spectrum analyzer

NASA Technical Reports Server (NTRS)

Zimmerman, G. A.; Garyantes, M. F.; Grimm, M. J.; Charny, B.

1991-01-01

A polyphase fast Fourier transform (FFT) spectrum analyzer being designed for NASA's Search for Extraterrestrial Intelligence (SETI) Sky Survey at the Jet Propulsion Laboratory is described. By replacing the time domain multiplicative window preprocessing with polyphase filter processing, much of the processing loss of windowed FFTs can be eliminated. Polyphase coefficient memory costs are minimized by effective use of run length compression. Finite word length effects are analyzed, producing a balanced system with 8 bit inputs, 16 bit fixed point polyphase arithmetic, and 24 bit fixed point FFT arithmetic. Fixed point renormalization midway through the computation is seen to be naturally accommodated by the matrix FFT algorithm proposed. Simulation results validate the finite word length arithmetic analysis and the renormalization technique.

On the theory of 3-phase squirrel-cage induction motors including space harmonics and mutual slotting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Papp, G.C.

1991-03-01

In this paper general equations for the asynchronous squirrel-cage motor which contain the influence of space harmonics and the mutual slotting are derived by using among others the power-invariant symmetrical component transformation and a time-dependent transformation with which, under certain circumstances, the rotor-position angle can be removed from the coefficient matrix. The developed models implemented in a machine-independent computer program form powerful tools, with which the influence of space harmonics in relation to the geometric data of specific motors can be analyzed for steady-state and transient performances.

FORTRAN program for induction motor analysis

NASA Technical Reports Server (NTRS)

Bollenbacher, G.

1976-01-01

A FORTRAN program for induction motor analysis is described. The analysis includes calculations of torque-speed characteristics, efficiency, losses, magnetic flux densities, weights, and various electrical parameters. The program is limited to three-phase Y-connected, squirrel-cage motors. Detailed instructions for using the program are given. The analysis equations are documented, and the sources of the equations are referenced. The appendixes include a FORTRAN symbol list, a complete explanation of input requirements, and a list of error messages.

A wireless power transmission system for implantable devices in freely moving rodents.

PubMed

Eom, Kyungsik; Jeong, Joonsoo; Lee, Tae Hyung; Kim, Jinhyung; Kim, Junghoon; Lee, Sung Eun; Kim, Sung June

2014-08-01

Reliable wireless power delivery for implantable devices in animals is highly desired for safe and effective experimental use. Batteries require frequent replacement; wired connections are inconvenient and unsafe, and short-distance inductive coupling requires the attachment of an exterior transmitter to the animal's body. In this article, we propose a solution by which animals with implantable devices can move freely without attachments. Power is transmitted using coils attached to the animal's cage and is received by a receiver coil implanted in the animal. For a three-dimensionally uniform delivery of power, we designed a columnar dual-transmitter coil configuration. A resonator-based inductive link was adopted for efficient long-range power delivery, and we used a novel biocompatible liquid crystal polymer substrate as the implantable receiver device. Using this wireless power delivery system, we obtain an average power transfer efficiency of 15.2% (minimum efficiency of 10% and a standard deviation of 2.6) within a cage of 15×20×15 cm3.

Columnar transmitter based wireless power delivery system for implantable device in freely moving animals.

PubMed

Eom, Kyungsik; Jeong, Joonsoo; Lee, Tae Hyung; Lee, Sung Eun; Jun, Sang Bum; Kim, Sung June

2013-01-01

A wireless power delivery system is developed to deliver electrical power to the neuroprosthetic devices that are implanted into animals freely moving inside the cage. The wireless powering cage is designed for long-term animal experiments without cumbersome wires for power supply or the replacement of batteries. In the present study, we propose a novel wireless power transmission system using resonator-based inductive links to increase power efficiency and to minimize the efficiency variations. A columnar transmitter coil is proposed to provide lateral uniformity of power efficiency. Using this columnar transmitter coil, only 7.2% efficiency fluctuation occurs from the maximum transmission efficiency of 25.9%. A flexible polymer-based planar type receiver coil is fabricated and assembled with a neural stimulator and an electrode. Using the designed columnar transmitter coil, the implantable device successfully operates while it moves freely inside the cage.

Polyphasic taxonomy, a consensus approach to bacterial systematics.

PubMed Central

Vandamme, P; Pot, B; Gillis, M; de Vos, P; Kersters, K; Swings, J

1996-01-01

Over the last 25 years, a much broader range of taxonomic studies of bacteria has gradually replaced the former reliance upon morphological, physiological, and biochemical characterization. This polyphasic taxonomy takes into account all available phenotypic and genotypic data and integrates them in a consensus type of classification, framed in a general phylogeny derived from 16S rRNA sequence analysis. In some cases, the consensus classification is a compromise containing a minimum of contradictions. It is thought that the more parameters that will become available in the future, the more polyphasic classification will gain stability. In this review, the practice of polyphasic taxonomy is discussed for four groups of bacteria chosen for their relevance, complexity, or both: the genera Xanthomonas and Campylobacter, the lactic acid bacteria, and the family Comamonadaceae. An evaluation of our present insights, the conclusions derived from it, and the perspectives of polyphasic taxonomy are discussed, emphasizing the keystone role of the species. Taxonomists did not succeed in standardizing species delimitation by using percent DNA hybridization values. Together with the absence of another "gold standard" for species definition, this has an enormous repercussion on bacterial taxonomy. This problem is faced in polyphasic taxonomy, which does not depend on a theory, a hypothesis, or a set of rules, presenting a pragmatic approach to a consensus type of taxonomy, integrating all available data maximally. In the future, polyphasic taxonomy will have to cope with (i) enormous amounts of data, (ii) large numbers of strains, and (iii) data fusion (data aggregation), which will demand efficient and centralized data storage. In the future, taxonomic studies will require collaborative efforts by specialized laboratories even more than now is the case. Whether these future developments will guarantee a more stable consensus classification remains an open question. PMID:8801440

Modelling high frequency phenomena in the rotor of induction motors under no-load test conditions

NASA Astrophysics Data System (ADS)

Boglietti, Aldo; Bottauscio, Oriano; Chiampi, Mario; Lazzari, Mario

2003-01-01

The paper aims to deep the electromagnetic phenomena in the rotor of induction motors produced during the no-load test by the high-order harmonics of the spatial distribution of magnetic flux. The analysis is carried out by a flux driven finite element procedure, which can take into account the hysteresis of magnetic material, the induced currents in rotor cage and the eddy currents in the laminations. The computed results, including losses and local waveforms of electrical and magnetic quantities, are finally discussed.

Dual stator winding variable speed asynchronous generator: optimal design and experiments

NASA Astrophysics Data System (ADS)

Tutelea, L. N.; Deaconu, S. I.; Popa, G. N.

2015-06-01

In the present paper is carried out a theoretical and experimental study of dual stator winding squirrel cage asynchronous generator (DSWA) behavior in the presence of saturation regime (non-sinusoidal) due to the variable speed operation. The main aims are the determination of the relations of calculating the equivalent parameters of the machine windings to optimal design using a Matlab code. Issue is limited to three phase range of double stator winding cage-induction generator of small sized powers, the most currently used in the small adjustable speed wind or hydro power plants. The tests were carried out using three-phase asynchronous generator having rated power of 6 [kVA].

Flywheel induction motor-generator for magnet power supply in small fusion device.

PubMed

Hatakeyma, S; Yoshino, F; Tsutsui, H; Tsuji-Iio, S

2016-04-01

A flywheel motor-generator (MG) for the toroidal field (TF) coils of a small fusion device was developed which utilizes a commercially available squirrel-cage induction motor. Advantages of the MG are comparably-long duration, quick power response, and easy implementation of power control compared with conventional capacitor-type power supply. A 55-kW MG was fabricated, and TF coils of a small fusion device were energized. The duration of the current flat-top was extended to 1 s which is much longer than those of conventional small devices (around 10-100 ms).

Flywheel induction motor-generator for magnet power supply in small fusion device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hatakeyma, S., E-mail: hatakeyama.shoichi@torus.nr.titech.ac.jp; Yoshino, F.; Tsutsui, H.

2016-04-15

A flywheel motor-generator (MG) for the toroidal field (TF) coils of a small fusion device was developed which utilizes a commercially available squirrel-cage induction motor. Advantages of the MG are comparably-long duration, quick power response, and easy implementation of power control compared with conventional capacitor-type power supply. A 55-kW MG was fabricated, and TF coils of a small fusion device were energized. The duration of the current flat-top was extended to 1 s which is much longer than those of conventional small devices (around 10–100 ms).

Analytical and experimental study of high phase order induction motors

NASA Technical Reports Server (NTRS)

Klingshirn, Eugene A.

1989-01-01

Induction motors having more than three phases were investigated to determine their suitability for electric vehicle applications. The objective was to have a motor with a current rating lower than that of a three-phase motor. The name chosen for these is high phase order (HPO) motors. Motors having six phases and nine phases were given the most attention. It was found that HPO motors are quite suitable for electric vehicles, and for many other applications as well. They have characteristics which are as good as or better than three-phase motors for practically all applications where polyphase induction motors are appropriate. Some of the analysis methods are presented, and several of the equivalent circuits which facilitate the determination of harmonic currents and losses, or currents with unbalanced sources, are included. The sometimes large stator currents due to harmonics in the source voltages are pointed out. Filters which can limit these currents were developed. An analysis and description of these filters is included. Experimental results which confirm and illustrate much of the theory are also included. These include locked rotor test results and full-load performance with an open phase. Also shown are oscillograms which display the reduction in harmonic currents when a filter is used with the experimental motor supplied by a non-sinusoidal source.

Anterior Cervical Fusion with Stand-alone Trabecular Metal Cages to Treat Cervical Myelopathy Caused by Degenerative Disk Disease. Observations in 88 Cases with Minimum 12-month Follow-up.

PubMed

Mastronardi, Luciano; Roperto, Raffaelino; Cacciotti, Guglielmo; Calvosa, Francesco

2018-06-14

 Anterior cervical fusion (ACF) with autologous bone was reported > 50 years ago. The continuous development of materials with elastic properties close to that of the cortical bone improves induction of osteogenesis and simplifies the technique of interbody fusion. To determine the safety and efficiency of stand-alone trabecular metal (TM) (or porous tantalum) cages for ACF, we performed a retrospective analysis of 88 consecutive patients with one-level or two-level degenerative disk disease (DDD) causing cervical myelopathy treated by interbody fusion with stand-alone TM cages.  During a 65-month period, 88 consecutive patients had ACF at 105 levels between C3 and C7. All surgeries involved one- or two-segmental DDD producing mild or severe cervical spine myelopathy, in 31 patients (35.2%), associated with unilateral or bilateral radiculopathy. We implanted all disk spaces with unfilled TM trapezoidal cages (Zimmer Biomet Spine, Broomfield, Colorado, United States).  At a mean follow-up of 31 months (range: 12-65 months), 95.4% of patients had a good to excellent outcome, with subjective and objective improvement of myelopathy; the result was fair in two and poor in two other patients. Radicular pain and/or any deficits disappeared in 84 patients (95.4%) complaining of preoperative myeloradiculopathy. The fusion rate was 68.2% at 6 months and 100% at 1 year. Device fragmentation was never observed. In two cases, a second operation with removal of TM cages, corpectomy, expansion cages, and plating was necessary.  TM cages appear to be safe and efficient for ACF in DDD patients with myelopathy. To confirm our preliminary impressions, larger studies with long-term follow-up are necessary. Georg Thieme Verlag KG Stuttgart · New York.

Computer-Aided Teaching Using MATLAB/Simulink for Enhancing an IM Course With Laboratory Tests

ERIC Educational Resources Information Center

Bentounsi, A.; Djeghloud, H.; Benalla, H.; Birem, T.; Amiar, H.

2011-01-01

This paper describes an automatic procedure using MATLAB software to plot the circle diagram for two induction motors (IMs), with wound and squirrel-cage rotors, from no-load and blocked-rotor tests. The advantage of this approach is that it avoids the need for a direct load test in predetermining the IM characteristics under reduced power.…

Detection of air-gap eccentricity and broken-rotor bar conditions in a squirrel-cage induction motor using the radial flux sensor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hwang, Don-Ha; Woo, Byung-Chul; Sun, Jong-Ho

2008-04-01

A new method for detecting eccentricity and broken rotor bar conditions in a squirrel-cage induction motor is proposed. Air-gap flux variation analysis is done using search coils, which are inserted at stator slots. Using this method, the leakage flux in radial direction can be directly detected. Using finite element method, the air-gap flux variation is accurately modeled and analyzed. From the results of the simulation, a motor under normal condition shows maximum magnetic flux density of 1.3 T. On the other hand, the eccentric air-gap condition displays about 1.1 T at 60 deg. and 1.6 T at 240 deg. Amore » difference of flux density is 0.5 T in the abnormal condition, whereas no difference is detected in the normal motor. In the broken rotor bar conditions, the flux densities at 65 deg. and 155 deg. are about 0.4 T and 0.8 T, respectively. These simulation results are coincided with those of experiment. Consequently, the measurement of the magnetic flux at air gap is one of effective ways to discriminate the faulted conditions of the eccentricity and broken rotor bars.« less

Wireless Monitoring of Induction Machine Rotor Physical Variables

PubMed Central

Doolan Fernandes, Jefferson; Carvalho Souza, Francisco Elvis; de Paiva, José Alvaro

2017-01-01

With the widespread use of electric machines, there is a growing need to extract information from the machines to improve their control systems and maintenance management. The present work shows the development of an embedded system to perform the monitoring of the rotor physical variables of a squirrel cage induction motor. The system is comprised of: a circuit to acquire desirable rotor variable(s) and value(s) that send it to the computer; a rectifier and power storage circuit that converts an alternating current in a continuous current but also stores energy for a certain amount of time to wait for the motor’s shutdown; and a magnetic generator that harvests energy from the rotating field to power the circuits mentioned above. The embedded system is set on the rotor of a 5 HP squirrel cage induction motor, making it difficult to power the system because it is rotating. This problem can be solved with the construction of a magnetic generator device to avoid the need of using batteries or collector rings and will send data to the computer using a wireless NRF24L01 module. For the proposed system, initial validation tests were made using a temperature sensor (DS18b20), as this variable is known as the most important when identifying the need for maintenance and control systems. Few tests have shown promising results that, with further improvements, can prove the feasibility of using sensors in the rotor. PMID:29156564

Wireless Monitoring of Induction Machine Rotor Physical Variables.

PubMed

Doolan Fernandes, Jefferson; Carvalho Souza, Francisco Elvis; Cipriano Maniçoba, Glauco George; Salazar, Andrés Ortiz; de Paiva, José Alvaro

2017-11-18

With the widespread use of electric machines, there is a growing need to extract information from the machines to improve their control systems and maintenance management. The present work shows the development of an embedded system to perform the monitoring of the rotor physical variables of a squirrel cage induction motor. The system is comprised of: a circuit to acquire desirable rotor variable(s) and value(s) that send it to the computer; a rectifier and power storage circuit that converts an alternating current in a continuous current but also stores energy for a certain amount of time to wait for the motor's shutdown; and a magnetic generator that harvests energy from the rotating field to power the circuits mentioned above. The embedded system is set on the rotor of a 5 HP squirrel cage induction motor, making it difficult to power the system because it is rotating. This problem can be solved with the construction of a magnetic generator device to avoid the need of using batteries or collector rings and will send data to the computer using a wireless NRF24L01 module. For the proposed system, initial validation tests were made using a temperature sensor (DS18b20), as this variable is known as the most important when identifying the need for maintenance and control systems. Few tests have shown promising results that, with further improvements, can prove the feasibility of using sensors in the rotor.

Frequency-Offset Cartesian Feedback Based on Polyphase Difference Amplifiers

PubMed Central

Zanchi, Marta G.; Pauly, John M.; Scott, Greig C.

2010-01-01

A modified Cartesian feedback method called “frequency-offset Cartesian feedback” and based on polyphase difference amplifiers is described that significantly reduces the problems associated with quadrature errors and DC-offsets in classic Cartesian feedback power amplifier control systems. In this method, the reference input and feedback signals are down-converted and compared at a low intermediate frequency (IF) instead of at DC. The polyphase difference amplifiers create a complex control bandwidth centered at this low IF, which is typically offset from DC by 200–1500 kHz. Consequently, the loop gain peak does not overlap DC where voltage offsets, drift, and local oscillator leakage create errors. Moreover, quadrature mismatch errors are significantly attenuated in the control bandwidth. Since the polyphase amplifiers selectively amplify the complex signals characterized by a +90° phase relationship representing positive frequency signals, the control system operates somewhat like single sideband (SSB) modulation. However, the approach still allows the same modulation bandwidth control as classic Cartesian feedback. In this paper, the behavior of the polyphase difference amplifier is described through both the results of simulations, based on a theoretical analysis of their architecture, and experiments. We then describe our first printed circuit board prototype of a frequency-offset Cartesian feedback transmitter and its performance in open and closed loop configuration. This approach should be especially useful in magnetic resonance imaging transmit array systems. PMID:20814450

Outside the Hull Electric Propulsion for a Submarine

DTIC Science & Technology

1990-05-01

improvements. Outside The Hull Electric Propulsion ’OTHEP) uses an inverted geometry, squirrel-cage induction motor to drive a large hub-to-diameter ratio...which is used for shipboard air- borne noise prediction, is adapted to describe the noise which is radiated into the sea. With the estimated...123 5 4.2.3 Using the Forces as Input to Acoustic Analysis S. .. . . . . . .... . . . . . . . . . . . . .. . . . ... . . . . . . . 1 2

Oxidative stability of the meat of broilers supplemented with rosemary leaves, rosehip fruits, chokeberry pomace, and entire nettle, and effects on performance and meat quality.

PubMed

Loetscher, Y; Kreuzer, M; Messikommer, R E

2013-11-01

Prevention of lipid oxidation needs special attention because a high proportion of fatty acids in broiler meat are unsaturated. A feeding experiment was conducted to evaluate the antioxidant effect of dietary addition of rosemary, chokeberry pomace, rosehip, or nettle in comparison with vitamin E. Male Ross PM3 broilers caged in groups of 6 (4 replicated cages per treatment) were fed a balanced diet supplemented with 25 g/kg of herbal additive, 200 IU of α-tocopheryl acetate/kg, or without supplementation from d 7 to 35. Intake, performance, and with the help of excreta samples, apparent fiber digestibility, ME content, and metabolizability of nitrogen and energy were recorded per cage. Feed was analyzed for total phenols and tocopherols. In each bird (n = 24 per treatment), carcass weight and relative organ weights were recorded, and skin and liver color were assessed. Abdominal fat was analyzed for induction time (h) of lipid oxidation (Rancimat). Breast meat was analyzed for total tocopherol content (mg/kg) and development of TBA reactive substances (TBARS; μg of MDA/kg) over 9 d of storage. Data were subjected to ANOVA considering treatment and, where applicable, storage time. Rosemary supplementation reduced oxidation (TBARS d 9: 201; induction time: 2.48) and elevated tocopherol content (5.72) of the meat compared with control (470, 1.87, and 3.53, respectively). Rosemary-treated birds had a slightly lower carcass weight and a reduced nitrogen and energy metabolizability. Rosehip addition numerically decreased TBARS (319) and enhanced carcass weight (1.71 kg) compared with rosemary-treated birds (1.54 kg). Only a trend in antioxidant activity could be ascribed to chokeberry pomace, although dietary phenolic content was highest. Nettle did not improve oxidative stability (TBARS: 506; induction time: 1.91), although tocopherol content was elevated (6.51). Nettle treatment strongly intensified skin yellowness (b* of 20.6) compared with the control treatment (10.8). Clearly, rosemary is the most suitable dietary antioxidant investigated in this study, yet chokeberry and rosehip also exhibited interesting properties.

Reactive power generation in high speed induction machines by continuously occurring space-transients

NASA Astrophysics Data System (ADS)

Laithwaite, E. R.; Kuznetsov, S. B.

1980-09-01

A new technique of continuously generating reactive power from the stator of a brushless induction machine is conceived and tested on a 10-kw linear machine and on 35 and 150 rotary cage motors. An auxiliary magnetic wave traveling at rotor speed is artificially created by the space-transient attributable to the asymmetrical stator winding. At least two distinct windings of different pole-pitch must be incorporated. This rotor wave drifts in and out of phase repeatedly with the stator MMF wave proper and the resulting modulation of the airgap flux is used to generate reactive VA apart from that required for magnetization or leakage flux. The VAR generation effect increases with machine size, and leading power factor operation of the entire machine is viable for large industrial motors and power system induction generators.

A polyphase filter for many-core architectures

NASA Astrophysics Data System (ADS)

Adámek, K.; Novotný, J.; Armour, W.

2016-07-01

In this article we discuss our implementation of a polyphase filter for real-time data processing in radio astronomy. The polyphase filter is a standard tool in digital signal processing and as such a well established algorithm. We describe in detail our implementation of the polyphase filter algorithm and its behaviour on three generations of NVIDIA GPU cards (Fermi, Kepler, Maxwell), on the Intel Xeon CPU and Xeon Phi (Knights Corner) platforms. All of our implementations aim to exploit the potential for data reuse that the algorithm offers. Our GPU implementations explore two different methods for achieving this, the first makes use of L1/Texture cache, the second uses shared memory. We discuss the usability of each of our implementations along with their behaviours. We measure performance in execution time, which is a critical factor for real-time systems, we also present results in terms of bandwidth (GB/s), compute (GFLOP/s/s) and type conversions (GTc/s). We include a presentation of our results in terms of the sample rate which can be processed in real-time by a chosen platform, which more intuitively describes the expected performance in a signal processing setting. Our findings show that, for the GPUs considered, the performance of our polyphase filter when using lower precision input data is limited by type conversions rather than device bandwidth. We compare these results to an implementation on the Xeon Phi. We show that our Xeon Phi implementation has a performance that is 1.5 × to 1.92 × greater than our CPU implementation, however is not insufficient to compete with the performance of GPUs. We conclude with a comparison of our best performing code to two other implementations of the polyphase filter, showing that our implementation is faster in nearly all cases. This work forms part of the Astro-Accelerate project, a many-core accelerated real-time data processing library for digital signal processing of time-domain radio astronomy data.

Diagnosis of the three-phase induction motor using thermal imaging

NASA Astrophysics Data System (ADS)

Glowacz, Adam; Glowacz, Zygfryd

2017-03-01

Three-phase induction motors are used in the industry commonly for example woodworking machines, blowers, pumps, conveyors, elevators, compressors, mining industry, automotive industry, chemical industry and railway applications. Diagnosis of faults is essential for proper maintenance. Faults may damage a motor and damaged motors generate economic losses caused by breakdowns in production lines. In this paper the authors develop fault diagnostic techniques of the three-phase induction motor. The described techniques are based on the analysis of thermal images of three-phase induction motor. The authors analyse thermal images of 3 states of the three-phase induction motor: healthy three-phase induction motor, three-phase induction motor with 2 broken bars, three-phase induction motor with faulty ring of squirrel-cage. In this paper the authors develop an original method of the feature extraction of thermal images MoASoID (Method of Areas Selection of Image Differences). This method compares many training sets together and it selects the areas with the biggest changes for the recognition process. Feature vectors are obtained with the use of mentioned MoASoID and image histogram. Next 3 methods of classification are used: NN (the Nearest Neighbour classifier), K-means, BNN (the back-propagation neural network). The described fault diagnostic techniques are useful for protection of three-phase induction motor and other types of rotating electrical motors such as: DC motors, generators, synchronous motors.

An improved design method based on polyphase components for digital FIR filters

NASA Astrophysics Data System (ADS)

Kumar, A.; Kuldeep, B.; Singh, G. K.; Lee, Heung No

2017-11-01

This paper presents an efficient design of digital finite impulse response (FIR) filter, based on polyphase components and swarm optimisation techniques (SOTs). For this purpose, the design problem is formulated as mean square error between the actual response and ideal response in frequency domain using polyphase components of a prototype filter. To achieve more precise frequency response at some specified frequency, fractional derivative constraints (FDCs) have been applied, and optimal FDCs are computed using SOTs such as cuckoo search and modified cuckoo search algorithms. A comparative study of well-proved swarm optimisation, called particle swarm optimisation and artificial bee colony algorithm is made. The excellence of proposed method is evaluated using several important attributes of a filter. Comparative study evidences the excellence of proposed method for effective design of FIR filter.

Improved motors for utility applications: Volume 6, Squirrel-cage rotor analysis: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffith, J.W.; McCoy, R.M.

1986-11-01

An analysis of squirrel cage induction motor rotors was undertaken in response to an Industry Assessment Study finding 10% of motor failures to be rotor related. The analysis focuses on evaluating rotor design life. The evaluation combines state-of-the-art electromagnetic, thermal, and structural solution techniques into an integrated analysis and presents a simple summary. Finite element techniques are central tools in the analysis. The analysis is applied to a specific forced draft fan drive design. Fans as a category of application have a higher failure rate than other categories of power station auxiliary motor applications. Forced-draft fan drives are one ofmore » the major fan drives which accelerate a relatively high value of rotor load inertia. Various starting and operating conditions are studied for this forced-draft fan drive motor including a representative application duty cycle.« less

Problem of the thermodynamic status of the mixed-layer minerals

USGS Publications Warehouse

Zen, E.-A.

1962-01-01

Minerals that show mixed layering, particularly with the component layers in random sequence, pose problems because they may behave thermodynamically as single phases or as polyphase aggregates. Two operational criteria are proposed for their distinction. The first scheme requires two samples of mixed-layer material which differ only in the proportions of the layers. If each of these two samples are allowed to equilibrate with the same suitably chosen monitoring solution, then the intensive parameters of the solution will be invariant if the mixed-layer sample is a polyphase aggregate, but not otherwise. The second scheme makes use of the fact that portions of many titration curves of clay minerals show constancy of the chemical activities of the components in the equilibrating solutions, suggesting phase separation. If such phase separation occurs for a mixed-layer material, then, knowing the number of independent components in the system, it should be possible to decide on the number of phases the mixed-layer material represents. Knowledge of the phase status of mixed-layer material is essential to the study of the equilibrium relations of mineral assemblages involving such material, because a given mixed-layer mineral will be plotted and treated differently on a phase diagram, depending on whether it is a single phase or a polyphase aggregate. Extension of the titration technique to minerals other than the mixed-layer type is possible. In particular, this method may be used to determine if cryptoperthites and peristerites are polyphase aggregates. In general, for any high-order phase separation, the method may be used to decide just at what point in this continuous process the system must be regarded operationally as a polyphase aggregate. ?? 1962.

Measuring and Predicting Sleep and Performance During Military Operations

DTIC Science & Technology

2012-08-23

chronobiology , and functions of polyphasic and ultrashort sleep: main issues. In: Stampi C, ed. Why We Nap. Evolution, Chronobiology , and Functions...Alertness: Chronobiological , Behavioural and Medical Aspects of Napping. New York, NY: Raven Press; 1989: 205–220. 82. Dinges DF. Napping patterns and... Chronobiology , and Functions of Polyphasic and Ultrashort Sleep: Main Issues. Boston, Mass: Birkhaüser; 1992: 118–134. 84. Muzet A, Nicolas A, Tassi P

Cage-rotor induction motor inter-turn short circuit fault detection with and without saturation effect by MEC model.

PubMed

Naderi, Peyman

2016-09-01

The inter-turn short fault for the Cage-Rotor-Induction-Machine (CRIM) is studied in this paper and its local saturation is taken into account. However, in order to observe the exact behavior of machine, the Magnetic-Equivalent-Circuit (MEC) and nonlinear B-H curve are proposed to provide an insight into the machine model and saturation effect respectively. The electrical machines are generally operated near to their saturation zone due to some design necessities. Hence, when the machine is exposed to a fault such as short circuit or eccentricities, it is operated within its saturation zone and thus, time and space harmonics are integrated and as a result, current and torque harmonics are generated which the phenomenon cannot be explored when saturation is dismissed. Nonetheless, inter-turn short circuit may lead to local saturation and this occurrence is studied in this paper using MEC model. In order to achieve the mentioned objectives, two and also four-pole machines are modeled as two samples and the machines performances are analyzed in healthy and faulty cases with and without saturation effect. A novel strategy is proposed to precisely detect inter-turn short circuit fault according to the stator׳s lines current signatures and the accuracy of the proposed method is verified by experimental results. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

Sepsis-induced morbidity in mice: effects on body temperature, body weight, cage activity, social behavior and cytokines in brain

PubMed Central

Granger, Jill I.; Ratti, Pietro-Luca; Datta, Subhash C.; Raymond, Richard M.; Opp, Mark R.

2012-01-01

Infection negatively impacts mental health, as evidenced by the lethargy, malaise, and cognitive deficits experienced during illness. These changes in central nervous system processes, collectively termed sickness behavior, have been shown in animal models to be mediated primarily by the actions of cytokines in brain. Most studies of sickness behavior to date have used bolus injection of bacterial lipopolysaccharide (LPS) or selective administration of the proinflammatory cytokines interleukin-1β (IL-1β) or IL-6 as the immune challenge. Such models, although useful for determining mechanisms responsible for acute changes in physiology and behavior, do not adequately represent the more complex effects on central nervous system (CNS) processes of a true infection with replicating pathogens. In the present study, we used the cecal ligation and puncture (CLP) model to quantify sepsis-induced alterations in several facets of physiology and behavior of mice. We determined the impact of sepsis on cage activity, body temperature, food and water consumption and body weights of mice. Because cytokines are critical mediators of changes in behavior and temperature regulation during immune challenge, we also quantified sepsis-induced alterations in cytokine mRNA and protein in brain during the acute period of sepsis onset. We now report that cage activity and temperature regulation in mice that survive are altered for up to 23 days after sepsis induction. Food and water consumption are transiently reduced, and body weight is lost during sepsis. Furthermore, sepsis decreases social interactions for 24 – 48 hours. Finally, mRNA and protein for IL-1β, IL-6, and tumor necrosis factor-α (TNFα) are upregulated in the hypothalamus, hippocampus, and brain stem during sepsis onset, from 6–72 hour post sepsis induction. Collectively, these data indicate that sepsis not only acutely alters physiology, behavior and cytokine profiles in brain, but that some brain functions are impaired for long periods in animals that survive. PMID:23146654

Position and Orientation Insensitive Wireless Power Transmission for EnerCage-Homecage System.

PubMed

Jia, Yaoyao; Mirbozorgi, S Abdollah; Wang, Zheyuan; Hsu, Chia-Chun; Madsen, Teresa E; Rainnie, Donald; Ghovanloo, Maysam

2017-10-01

We have developed a new headstage architecture as part of a smart experimental arena, known as the EnerCage-HC2 system, which automatically delivers stimulation and collects behavioral data over extended periods with minimal small animal subject handling or personnel intervention in a standard rodent homecage. Equipped with a four-coil inductive link, the EnerCage-HC2 system wirelessly powers the receiver (Rx) headstage, irrespective of the subject's location or head orientation, eliminating the need for tethering or carrying bulky batteries. On the transmitter (Tx) side, a driver coil, five high-quality (Q) factor segmented resonators at different heights and orientations, and a closed-loop Tx power controller create a homogeneous electromagnetic (EM) field within the homecage 3-D space, and compensate for drops in power transfer efficiency (PTE) due to Rx misalignments. The headstage is equipped with four small slanted resonators, each covering a range of head orientations with respect to the Tx resonators, which direct the EM field toward the load coil at the bottom of the headstage. Moreover, data links based on Wi-Fi, UART, and Bluetooth low energy are utilized to enables remote communication and control of the Rx. The PTE varies within 23.6%-33.3% and 6.7%-10.1% at headstage heights of 8 and 20 cm, respectively, while continuously delivering >40 mW to the Rx electronics even at 90° rotation. As a proof of EnerCage-HC2 functionality in vivo, a previously documented on-demand electrical stimulation of the globus pallidus, eliciting consistent head rotation, is demonstrated in three freely behaving rats.

A Micro-Electrode Array device coupled to a laser-based system for the local stimulation of neurons by optical release of glutamate.

PubMed

Ghezzi, Diego; Menegon, Andrea; Pedrocchi, Alessandra; Valtorta, Flavia; Ferrigno, Giancarlo

2008-10-30

Optical stimulation is a promising approach to investigate the local dynamic responses of cultured neurons. In particular, flash photolysis of caged compounds offers the advantage of allowing the rapid change of concentration of either extracellular or intracellular molecules, such as neurotransmitters or second messengers, for the stimulation or modulation of neuronal activity. We describe here the use of an ultra-violet (UV) laser diode coupled to an optical fibre for the local activation of caged compounds combined with a Micro-Electrode Array (MEA) device. Local uncaging was achieved by UV irradiation through the optical fibre previously positioned by using a red laser diode. The size of the stimulation was determined using caged fluorescein, whereas its efficacy was tested by studying the effect of uncaging the neurotransmitter glutamate. Uncaged glutamate evoked neuronal responses that were recorded using either fluorescence measurements or electrophysiological recordings with MEAs, thus showing the ability of our system to induce local neuronal excitation. This method allows overcoming the limitations of the MEA system related to unfocused electrical stimulation and induction of electrical artefacts. In addition, the coupling of a UV laser diode to an optical fibre allows a precise local stimulation and a quick change of the stimulation point.

Exploration of the Genomic Diversity and Core Genome of the Bifidobacterium adolescentis Phylogenetic Group by Means of a Polyphasic Approach

PubMed Central

Duranti, Sabrina; Turroni, Francesca; Milani, Christian; Foroni, Elena; Bottacini, Francesca; Dal Bello, Fabio; Ferrarini, Alberto; Delledonne, Massimo; van Sinderen, Douwe

2013-01-01

In the current work, we describe genome diversity and core genome sequences among representatives of three bifidobacterial species, i.e., Bifidobacterium adolescentis, Bifidobacterium catenulatum, and Bifidobacterium pseudocatenulatum, by employing a polyphasic approach involving analysis of 16S rRNA gene and 16S-23S internal transcribed spacer (ITS) sequences, pulsed-field gel electrophoresis (PFGE), and comparative genomic hybridization (CGH) assays. PMID:23064340

A solid-state controller for a wind-driven slip-ring induction generator

NASA Astrophysics Data System (ADS)

Velayudhan, C.; Bundell, J. H.; Leary, B. G.

1984-08-01

The three-phase induction generator appears to become the preferred choice for wind-powered systems operated in parallel with existing power systems. A problem arises in connection with the useful operating speed range of the squirrel-cage machine, which is relatively narrow, as, for instance, in the range from 1 to 1.15. Efficient extraction of energy from a wind turbine, on the other hand, requires a speed range, perhaps as large as 1 to 3. One approach for 'matching' the generator to the turbine for the extraction of maximum power at any usable wind speed involves the use of a slip-ring induction machine. The power demand of the slip-ring machine can be matched to the available output from the wind turbine by modifying the speed-torque characteristics of the generator. A description is presented of a simple electronic rotor resistance controller which can optimize the power taken from a wind turbine over the full speed range.

Design of motor induction 3-Phase from waste industry to generator for microhydro at isolated village

NASA Astrophysics Data System (ADS)

Rimbawati; Azis Hutasuhut, Abdul; Irsan Pasaribu, Faisal; Cholish; Muharnif

2017-09-01

There is an electric machine that can operate as a generator either single-phase or three-phase in almost every household and industry today. This electric engine cannot be labeled as a generator but can be functioned as a generator. The machine that is mentioned is “squirrel cage motors” or it is well-known as induction motor that can be found in water pumps, washing machines, fans, blowers and other industrial machines. The induction motor can be functioned as a generator when the rotational speed of the rotor is made larger than the speed of the rotary field. In this regard, this study aims to modify the remains of 3-phase induction motor to be a permanent generator. Data of research based conducted on the river flow of Rumah Sumbul Village, STM Hulu district of Deli Serdang. The method of this research is by changing rotor and stator winding on a 3 phase induction motor, so it can produce a generator with rotation speed of 500 rpm. Based on the research, it can be concluded that the output voltage generator has occurred a voltage drop 10% between before and after loading for Star circuit and 2% for Delta circuit.

Range Sidelobe Response from the Use of Polyphase Signals in Spotlight Synthetic Aperture Radar

DTIC Science & Technology

2015-12-01

come to closure. I also want to thank my mother for raising me and instilling in me the work ethic and values that have propelled me through life. I...to describe the poly-phase signals at baseband. IQ notation is preferred for complex waveforms because it allows for an easy mathematical...variables. 15 Once the Frank-coded phase vector is created, the IQ signal generation discussed in Chapter II was used to generate a Frank-code phase

Trap-effectiveness and response to tiletamine-zolazepam and medetomidine anaesthesia in Eurasian wild boar captured with cage and corral traps

PubMed Central

2013-01-01

Background Capture, handling and chemical restraint are basic techniques often needed for research or management purposes. The aim of this study was testing a combination of tiletamine-zolazepam (TZ) (3 mg/kg) and medetomidine (M) (0.05 mg/kg) on Eurasian wild boar (Sus scrofa). A total of 77 free-ranging wild boar were captured by means of portable cages and corral traps and then anaesthetized with intramuscular darts using a blowpipe. The individual response to chemical immobilization was characterized using anaesthetic, clinical, and serum biochemical variables. After the procedure, 14 of these wild boar were monitored for 20 days using GPS-GSM collars. Results Pre-release mortality during capture and handling (6.5%) was associated with severe trauma in corral traps. Capture specificity for wild boar was 96.3% and trapping effort was 16.5 days per captured wild boar. Mean induction period was 4.5 ± 2.2 min, hypnosis period enabling effective handling was 61.6 ± 25.4 min, and recovery period was 12.8 ± 12.1 min. No heart or respiratory failure due to added stress occurred and post-release monitoring by GPS-devices revealed no mortality due to anaesthesia. According to the best statistical model obtained, the main factor driving anaesthetic efficacy and stress indicators is trap type. Conclusions Both cage and corral traps are efficient methods to capture wild boar. Cage traps are safer, as demonstrated by mortality rates as well as anaesthetic, physiological, and serum biochemical responses. This anaesthetic protocol is useful for prolonged handling of wild boar and allows sampling and collecting data for ecological and epidemiological studies. PMID:23702232

Polyphasic Temporal Behavior of Finger-Tapping Performance: A Measure of Motor Skills and Fatigue.

PubMed

Aydin, Leyla; Kiziltan, Erhan; Gundogan, Nimet Unay

2016-01-01

Successive voluntary motor movement involves a number of physiological mechanisms and may reflect motor skill development and neuromuscular fatigue. In this study, the temporal behavior of finger tapping was investigated in relation to motor skills and fatigue by using a long-term computer-based test. The finger-tapping performances of 29 healthy male volunteers were analyzed using linear and nonlinear regression models established for inter-tapping interval. The results suggest that finger-tapping performance exhibits a polyphasic nature, and has several characteristic time points, which may be directly related to muscle dynamics and energy consumption. In conclusion, we believe that future studies evaluating the polyphasic nature of the maximal voluntary movement will lead to the definition of objective scales that can be used in the follow up of some neuromuscular diseases, as well as, the determination of motor skills, individual ability, and peripheral fatigue through the use of a low cost, easy-to-use computer-based finger-tapping test.

Pole-zero form fractional model identification in frequency domain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mansouri, R.; Djamah, T.; Djennoune, S.

2009-03-05

This paper deals with system identification in the frequency domain using non integer order models given in the pole-zero form. The usual identification techniques cannot be used in this case because of the non integer orders of differentiation which makes the problem strongly nonlinear. A general identification method based on Levenberg-Marquardt algorithm is developed and allows to estimate the (2n+2m+1) parameters of the model. Its application to identify the ''skin effect'' of a squirrel cage induction machine modeling is then presented.

Development of a metal detector for smartphones and its use in the teaching laboratory

NASA Astrophysics Data System (ADS)

Sobral, G. A.

2018-07-01

In this article, we describe how to develop an inductive metal detector that can be integrated to any Android or iOS smartphone with a standard audio port at low cost. The results indicate the metal detector can be used in the physics teaching laboratory as a practical application of principles of electromagnetism. It allows one to differentiate ferromagnetic samples from the diamagnetic and paramagnetic ones and can also be used to investigate the direction of alternating magnetic fields and to demonstrate the Faraday’s cage shielding effect.

Method and apparatus for reducing the harmonic currents in alternating-current distribution networks

DOEpatents

Beverly, Leon H.; Hance, Richard D.; Kristalinski, Alexandr L.; Visser, Age T.

1996-01-01

An improved apparatus and method reduce the harmonic content of AC line and neutral line currents in polyphase AC source distribution networks. The apparatus and method employ a polyphase Zig-Zag transformer connected between the AC source distribution network and a load. The apparatus and method also employs a mechanism for increasing the source neutral impedance of the AC source distribution network. This mechanism can consist of a choke installed in the neutral line between the AC source and the Zig-Zag transformer.

Method and apparatus for reducing the harmonic currents in alternating-current distribution networks

DOEpatents

Beverly, L.H.; Hance, R.D.; Kristalinski, A.L.; Visser, A.T.

1996-11-19

An improved apparatus and method reduce the harmonic content of AC line and neutral line currents in polyphase AC source distribution networks. The apparatus and method employ a polyphase Zig-Zag transformer connected between the AC source distribution network and a load. The apparatus and method also employs a mechanism for increasing the source neutral impedance of the AC source distribution network. This mechanism can consist of a choke installed in the neutral line between the AC source and the Zig-Zag transformer. 23 figs.

Apparatus for controlling the firing of rectifiers in polyphase rectifying circuits

DOEpatents

Yarema, R.J.

1979-09-18

A polyphase rectifier is controlled with precision by a circuit that filters and shifts a reference signal associated with each phase and that starts a ramp signal at a zero crossing of the shifted reference signal. The difference between the ramp signal and an external trigger signal is used to generate a pulse that switches power rectifiers into conduction. The circuit reduces effects of variations that introduce subharmonics into a rectified signal and it can be used for constant or time-varying external trigger signals.

PWM-switching pattern-based diagnosis scheme for single and multiple open-switch damages in VSI-fed induction motor drives.

PubMed

Trabelsi, Mohamed; Boussak, Mohamed; Gossa, Moncef

2012-03-01

This paper deals with a fault detection technique for insulated-gate bipolar transistors (IGBTs) open-circuit faults in voltage source inverter (VSI)-fed induction motor drives. The novelty of this idea consists in analyzing the pulse-width modulation (PWM) switching signals and the line-to-line voltage levels during the switching times, under both healthy and faulty operating conditions. The proposed method requires line-to-line voltage measurement, which provides information about switching states and is not affected by the load. The fault diagnosis scheme is achieved using simple hardware and can be included in the existing inverter system without any difficulty. In addition, it allows not only accurate single and multiple faults diagnosis but also minimization of the fault detection time to a maximum of one switching period (T(c)). Simulated and experimental results on a 3-kW squirrel-cage induction motor drive are displayed to validate the feasibility and the effectiveness of the proposed strategy. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

Isolation and polyphasic characterization of a novel hyper catalase producing thermophilic bacterium for the degradation of hydrogen peroxide.

PubMed

Sooch, Balwinder Singh; Kauldhar, Baljinder Singh; Puri, Munish

2016-11-01

A newly isolated microbial strain of thermophilic genus Geobacillus has been described with emphasis on polyphasic characterization and its application for degradation of hydrogen peroxide. The validation of this thermophilic strain of genus Geobacillus designated as BSS-7 has been demonstrated by polyphasic taxonomy approaches through its morphological, biochemical, fatty acid methyl ester profile and 16S rDNA sequencing. This thermophilic species of Geobacillus exhibited growth at broad pH and temperature ranges coupled with production of extraordinarily high quantities of intracellular catalase, the latter of which as yet not been reported in any member of this genus. The isolated thermophilic bacterial culture BSS-7 exhibited resistance against a variety of organic solvents. The immobilized whole cells of the bacterium successfully demonstrated the degradation of hydrogen peroxide (H2O2) in a packed bed reactor. This strain has potential application in various analytical and diagnostic methods in the form of biosensors and biomarkers in addition to applications in the textile, paper, food and pharmaceutical industries.

Phototaxis of Oil Droplets Comprising a Caged Fatty Acid Tightly Linked to Internal Convection.

PubMed

Suzuki, Kentaro; Sugawara, Tadashi

2016-08-04

We found that novel sub-millimeter-sized photoactive oil droplets of oleic acid bearing a photolabile protecting group, 2-nitrobenzyl oleate (NBO), in basic water exhibited unidirectional motion toward a UV light source. This unidirectional motion can be explained by anisotropic photolysis on a surface of the NBO droplet with low permeability for UV light. Time-dependent changes of the movement under UV irradiation occurred in a cascade manner (still-standing, induction, and active stages). The velocity of the UV-irradiated droplet in the induction stage was small, but it was accelerated sixteen times by the presence of an inner convection structure, which was created by continued photolysis. This characteristic dynamics, which is derived from a supramolecular machinery system towards the external stimulus, may be similar to the phototaxis of a living cell. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Induction motor broken rotor bar fault location detection through envelope analysis of start-up current using Hilbert transform

NASA Astrophysics Data System (ADS)

Abd-el-Malek, Mina; Abdelsalam, Ahmed K.; Hassan, Ola E.

2017-09-01

Robustness, low running cost and reduced maintenance lead Induction Motors (IMs) to pioneerly penetrate the industrial drive system fields. Broken rotor bars (BRBs) can be considered as an important fault that needs to be early assessed to minimize the maintenance cost and labor time. The majority of recent BRBs' fault diagnostic techniques focus on differentiating between healthy and faulty rotor cage. In this paper, a new technique is proposed for detecting the location of the broken bar in the rotor. The proposed technique relies on monitoring certain statistical parameters estimated from the analysis of the start-up stator current envelope. The envelope of the signal is obtained using Hilbert Transformation (HT). The proposed technique offers non-invasive, fast computational and accurate location diagnostic process. Various simulation scenarios are presented that validate the effectiveness of the proposed technique.

Oil shale processing as a source of aquatic pollution: monitoring of the biologic effects in caged and feral freshwater fish.

PubMed Central

Tuvikene, A; Huuskonen, S; Koponen, K; Ritola, O; Mauer, U; Lindström-Seppä, P

1999-01-01

The biologic effects of the oil shale industry on caged rainbow trout (Oncorhynchus mykiss) as well as on feral perch (Perca fluviatilis) and roach (Rutilus rutilus) were studied in the River Narva in northeast Estonia. The River Narva passes the oil shale mining and processing area and thus receives elevated amounts of polycyclic aromatic hydrocarbons (PAHs), heavy metals, and sulfates. The effects of the chemical load were monitored by measuring cytochrome P4501A (CYP1A)-dependent monooxygenase (MO) activities [7-ethoxyresorufin O-deethylase and aryl hydrocarbon hydroxylase (AHH)] as well as conjugation enzyme activities [glutathione S-transferase (GST) and UDP-glucuronosyltransferase] in the liver of fish. CYP1A induction was further studied by detecting the amount and occurrence of the CYP1A protein. Histopathology of tissues (liver, kidney, spleen, and intestine) and the percentage of micronuclei in fish erythrocytes were also determined. Selected PAHs and heavy metals (Cd, Cu, Hg, and Pb) were measured from fish muscle and liver. In spite of the significant accumulation of PAHs, there was no induction of MO activities in any studied fish species. When compared to reference samples, AHH activities were even decreased in feral fish at some of the exposed sites. Detection of CYP1A protein content and the distribution of the CYP1A enzyme by immunohistochemistry also did not show extensive CYP1A induction. Instead, GST activities were significantly increased at exposed sites. Detection of histopathology did not reveal major changes in the morphology of tissues. The micronucleus test also did not show any evidence of genotoxicity. Thus, from the parameters studied, GST activity was most affected. The lack of catalytic CYP1A induction in spite of the heavy loading of PAHs was not studied but has been attributed to the elevated content of other compounds such as heavy metals, some of which can act as inhibitors for MOs. Another possible explanation of this lack of induction is that through adaptation processes the fish could have lost some of their sensitivity to PAHs. Either complex pollution caused by oil shale processing masked part of the harmful effects measured in this study, or oil shale industry did not have any severe effects on fish in the River Narva. Our study illustrates the difficulties in estimating risk in cases where there are numerous various contaminants affecting the biota. Images Figure 1 Figure 2 PMID:10464075

Brain-wide maps of Fos expression during fear learning and recall.

PubMed

Cho, Jin-Hyung; Rendall, Sam D; Gray, Jesse M

2017-04-01

Fos induction during learning labels neuronal ensembles in the hippocampus that encode a specific physical environment, revealing a memory trace. In the cortex and other regions, the extent to which Fos induction during learning reveals specific sensory representations is unknown. Here we generate high-quality brain-wide maps of Fos mRNA expression during auditory fear conditioning and recall in the setting of the home cage. These maps reveal a brain-wide pattern of Fos induction that is remarkably similar among fear conditioning, shock-only, tone-only, and fear recall conditions, casting doubt on the idea that Fos reveals auditory-specific sensory representations. Indeed, novel auditory tones lead to as much gene induction in visual as in auditory cortex, while familiar (nonconditioned) tones do not appreciably induce Fos anywhere in the brain. Fos expression levels do not correlate with physical activity, suggesting that they are not determined by behavioral activity-driven alterations in sensory experience. In the thalamus, Fos is induced more prominently in limbic than in sensory relay nuclei, suggesting that Fos may be most sensitive to emotional state. Thus, our data suggest that Fos expression during simple associative learning labels ensembles activated generally by arousal rather than specifically by a particular sensory cue. © 2017 Cho et al.; Published by Cold Spring Harbor Laboratory Press.

Brain-wide maps of Fos expression during fear learning and recall

PubMed Central

Cho, Jin-Hyung; Rendall, Sam D.; Gray, Jesse M.

2017-01-01

Fos induction during learning labels neuronal ensembles in the hippocampus that encode a specific physical environment, revealing a memory trace. In the cortex and other regions, the extent to which Fos induction during learning reveals specific sensory representations is unknown. Here we generate high-quality brain-wide maps of Fos mRNA expression during auditory fear conditioning and recall in the setting of the home cage. These maps reveal a brain-wide pattern of Fos induction that is remarkably similar among fear conditioning, shock-only, tone-only, and fear recall conditions, casting doubt on the idea that Fos reveals auditory-specific sensory representations. Indeed, novel auditory tones lead to as much gene induction in visual as in auditory cortex, while familiar (nonconditioned) tones do not appreciably induce Fos anywhere in the brain. Fos expression levels do not correlate with physical activity, suggesting that they are not determined by behavioral activity-driven alterations in sensory experience. In the thalamus, Fos is induced more prominently in limbic than in sensory relay nuclei, suggesting that Fos may be most sensitive to emotional state. Thus, our data suggest that Fos expression during simple associative learning labels ensembles activated generally by arousal rather than specifically by a particular sensory cue. PMID:28331016

Polyphasic taxonomy of Aspergillus section Fumigati and its teleomorph Neosartorya

PubMed Central

Samson, R.A.; Hong, S.; Peterson, S.W.; Frisvad, J.C.; Varga, J.

2007-01-01

The taxonomy of Aspergillus section Fumigati with its teleomorph genus Neosartorya is revised. The species concept is based on phenotypic (morphology and extrolite profiles) and molecular (β-tubulin and calmodulin gene sequences) characters in a polyphasic approach. Four new taxa are proposed: N. australensis N. ferenczii, N. papuaensis and N. warcupii. All newly described and accepted species are illustrated. The section consists of 33 taxa: 10 strictly anamorphic Aspergillus species and 23 Neosartorya species. Four other Neosartorya species described previously were not available for this monograph, and consequently are relegated to the category of doubtful species. PMID:18490953

Biomechanical Analysis of Porous Additive Manufactured Cages for Lateral Lumbar Interbody Fusion: A Finite Element Analysis.

PubMed

Zhang, Zhenjun; Li, Hui; Fogel, Guy R; Liao, Zhenhua; Li, Yang; Liu, Weiqiang

2018-03-01

A porous additive manufactured (AM) cage may provide stability similar to that of traditional solid cages and may be beneficial to bone ingrowth. The biomechanical influence of various porous cages on stability, subsidence, stresses in cage, and facet contact force has not been fully described. The purpose of this study was to verify biomechanical effects of porous AM cages. The surgical finite element models with various cages were constructed. The partially porous titanium (PPT) cages and fully porous titanium (FPT) cages were applied. The mechanical parameters of porous materials were obtained by mechanical test. Then the porous AM cages were compared with solid titanium (TI) cage and solid polyetheretherketone (PEEK) cage. The 4 motion modes were simulated. Range of motion (ROM), cage stress, end plate stress, and facet joint force (FJF) were compared. For all the surgical models, ROM decreased by >90%. Compared with TI and PPT cages, PEEK and FPT cages substantially reduced the maximum stresses in cage and end plate in all motion modes. Compared with PEEK cages, the stresses in cage and end plate for FPT cages decreased, whereas the ROM increased. Comparing FPT cages, the stresses in cage and end plate decreased with increasing porosity, whereas ROM increased with increasing porosity. After interbody fusion, FJF was substantially reduced in all motion modes except for flexion. Fully porous cages may offer an alternative to solid PEEK cages in lateral lumbar interbody fusion. However, it may be prudent to further increase the porosity of the cage. Copyright © 2017 Elsevier Inc. All rights reserved.

Double-sided electromagnetic pump with controllable normal force for rapid solidification of liquid metals

DOEpatents

Kuznetsov, Stephen B.

1987-01-01

A system for casting liquid metals is provided with an electromagnetic pump which includes a pair of primary blocks each having a polyphase winding and being positioned to form a gap through which a movable conductive heat sink passes. A solidifying liquid metal sheet is deposited on the heat sink and the heat sink and sheet are held in compression by forces produced as a result of current flow through the polyphase windings. Shaded-pole interaction between the primary windings, heat sink and solidifying strip produce transverse forces which act to center the strip on the heat sink.

Double-sided electromagnetic pump with controllable normal force for rapid solidification of liquid metals

DOEpatents

Kuznetsov, S.B.

1987-01-13

A system for casting liquid metals is provided with an electromagnetic pump which includes a pair of primary blocks each having a polyphase winding and being positioned to form a gap through which a movable conductive heat sink passes. A solidifying liquid metal sheet is deposited on the heat sink and the heat sink and sheet are held in compression by forces produced as a result of current flow through the polyphase windings. Shaded-pole interaction between the primary windings, heat sink and solidifying strip produce transverse forces which act to center the strip on the heat sink. 5 figs.

ANTLR Tree Grammar Generator and Extensions

NASA Technical Reports Server (NTRS)

Craymer, Loring

2005-01-01

A computer program implements two extensions of ANTLR (Another Tool for Language Recognition), which is a set of software tools for translating source codes between different computing languages. ANTLR supports predicated- LL(k) lexer and parser grammars, a notation for annotating parser grammars to direct tree construction, and predicated tree grammars. [ LL(k) signifies left-right, leftmost derivation with k tokens of look-ahead, referring to certain characteristics of a grammar.] One of the extensions is a syntax for tree transformations. The other extension is the generation of tree grammars from annotated parser or input tree grammars. These extensions can simplify the process of generating source-to-source language translators and they make possible an approach, called "polyphase parsing," to translation between computing languages. The typical approach to translator development is to identify high-level semantic constructs such as "expressions," "declarations," and "definitions" as fundamental building blocks in the grammar specification used for language recognition. The polyphase approach is to lump ambiguous syntactic constructs during parsing and then disambiguate the alternatives in subsequent tree transformation passes. Polyphase parsing is believed to be useful for generating efficient recognizers for C++ and other languages that, like C++, have significant ambiguities.

Furnished Cage System and Hen Well-Being: Comparative Effects of Furnished Cages and Battery Cages on Behavioral Exhibitions in White Leghorn Chickens

USDA-ARS?s Scientific Manuscript database

The battery cage system is being banned in the European Union before or by 2012; and the furnished cage system will be the only cage system allowed after 2012. This study was conducted to examine the different effects of caging systems, furnished cages vs. battery cages, on bird behaviors. One hundr...

In vivo RF powering for advanced biological research.

PubMed

Zimmerman, Mark D; Chaimanonart, Nattapon; Young, Darrin J

2006-01-01

An optimized remote powering architecture with a miniature and implantable RF power converter for an untethered small laboratory animal inside a cage is proposed. The proposed implantable device exhibits dimensions less than 6 mmx6 mmx1 mm, and a mass of 100 mg including a medical-grade silicon coating. The external system consists of a Class-E power amplifier driving a tuned 15 cmx25 cm external coil placed underneath the cage. The implant device is located in the animal's abdomen in a plane parallel to the external coil and utilizes inductive coupling to receive power from the external system. A half-wave rectifier rectifies the received AC voltage and passes the resulting DC current to a 2.5 kOmega resistor, which represents the loading of an implantable microsystem. An optimal operating point with respect to operating frequency and number of turns in each coil inductor was determined by analyzing the system efficiency. The determined optimal operating condition is based on a 4-turn external coil and a 20-turn internal coil operating at 4 MHz. With the Class-E amplifier consuming a constant power of 25 W, this operating condition is sufficient to supply a desired 3.2 V with 1.3 mA to the load over a cage size of 10 cmx20 cm with an animal tilting angle of up to 60 degrees, which is the worst case considered for the prototype design. A voltage regulator can be designed to regulate the received DC power to a stable supply for the bio-implant microsystem.

Induction machine bearing faults detection based on a multi-dimensional MUSIC algorithm and maximum likelihood estimation.

PubMed

Elbouchikhi, Elhoussin; Choqueuse, Vincent; Benbouzid, Mohamed

2016-07-01

Condition monitoring of electric drives is of paramount importance since it contributes to enhance the system reliability and availability. Moreover, the knowledge about the fault mode behavior is extremely important in order to improve system protection and fault-tolerant control. Fault detection and diagnosis in squirrel cage induction machines based on motor current signature analysis (MCSA) has been widely investigated. Several high resolution spectral estimation techniques have been developed and used to detect induction machine abnormal operating conditions. This paper focuses on the application of MCSA for the detection of abnormal mechanical conditions that may lead to induction machines failure. In fact, this paper is devoted to the detection of single-point defects in bearings based on parametric spectral estimation. A multi-dimensional MUSIC (MD MUSIC) algorithm has been developed for bearing faults detection based on bearing faults characteristic frequencies. This method has been used to estimate the fundamental frequency and the fault related frequency. Then, an amplitude estimator of the fault characteristic frequencies has been proposed and fault indicator has been derived for fault severity measurement. The proposed bearing faults detection approach is assessed using simulated stator currents data, issued from a coupled electromagnetic circuits approach for air-gap eccentricity emulating bearing faults. Then, experimental data are used for validation purposes. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

The polymethyl methacrylate cervical cage for treatment of cervical disk disease Part III. Biomechanical properties.

PubMed

Chen, Jyi-Feng; Lee, Shih-Tseng

2006-10-01

In a previous article, we used the PMMA cervical cage in the treatment of single-level cervical disk disease and the preliminary clinical results were satisfactory. However, the mechanical properties of the PMMA cage were not clear. Therefore, we designed a comparative in vitro biomechanical study to determine the mechanical properties of the PMMA cage. The PMMA cervical cage and the Solis PEEK cervical cage were compressed in a materials testing machine to determine the mechanical properties. The compressive yield strength of the PMMA cage (7030 +/- 637 N) was less than that of the Solis polymer cervical cage (8100 +/- 572 N). The ultimate compressive strength of the PMMA cage (8160 +/- 724 N) was less than that of the Solis cage (9100 +/- 634 N). The stiffness of the PMMA cervical cage (8106 +/- 817 N/mm) was greater than that of the Solis cage (6486 +/- 530 N/mm). The elastic modulus of the PMMA cage (623 +/- 57 MPa) was greater than that of the Solis cage (510 +/- 42 MPa). The elongation of PMMA cage (43.5 +/- 5.7%) was larger than that of the Solis cage (36.1 +/- 4.3%). Although the compressive yield strength and ultimate compressive strength of the PMMA cervical cage were less than those of the Solis polymer cage, the mechanical properties are better than those of the cervical vertebral body. The PMMA cage is strong and safe for use as a spacer for cervical interbody fusion. Compared with other cage materials, the PMMA cage has many advantages and no obvious failings at present. However, the PMMA cervical cage warrants further long-term clinical study.

Serially-Connected Compensator for Eliminating the Unbalanced Three-Phase Voltage Impact on Wind Turbine Generators: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Z.; Hsu, P.; Muljadi, E.

2015-04-06

Untransposed transmission lines, unbalanced tap changer operations, and unbalanced loading in weak distribution lines can cause unbalanced-voltage conditions. The resulting unbalanced voltage at the point of interconnection affects proper gird integration and reduces the lifetime of wind turbines due to power oscillations, torque pulsations, mechanical stresses, energy losses, and uneven and overheating of the generator stator winding. This work investigates the dynamic impact of unbalanced voltage on the mechanical and electrical components of integrated Fatigue, Aerodynamics, Structures, and Turbulence (FAST) wind turbine generation systems (WTGs) of Type 1 (squirrel-cage induction generator) and Type 3 (doubly-fed induction generator). To alleviate thismore » impact, a serially-connected compensator for a three-phase power line is proposed to balance the wind turbine-side voltage. Dynamic simulation studies are conducted in MATLAB/Simulink to compare the responses of these two types of wind turbine models under normal and unbalanced-voltage operation conditions and demonstrate the effectiveness of the proposed compensator.« less

A Serially-Connected Compensator for Eliminating the Unbalanced Three-Phase Voltage Impact on Wind Turbine Generators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Ziping; Hsu, Ping; Muljadi, Eduard

2015-10-05

Untransposed transmission lines, unbalanced tap changer operations, and unbalanced loading in weak distribution lines can cause unbalanced-voltage conditions. The resulting unbalanced voltage at the point of interconnection affects proper gird integration and reduces the lifetime of wind turbines due to power oscillations, torque pulsations, mechanical stresses, energy losses, and uneven and overheating of the generator stator winding. This work investigates the dynamic impact of unbalanced voltage on the mechanical and electrical components of integrated Fatigue, Aerodynamics, Structures, and Turbulence (FAST) wind turbine generation systems (WTGs) of Type 1 (squirrel-cage induction generator) and Type 3 (doubly-fed induction generator). To alleviate thismore » impact, a serially-connected compensator for a three-phase power line is proposed to balance the wind turbine-side voltage. Dynamic simulation studies are conducted in MATLAB/Simulink to compare the responses of these two types of wind turbine models under normal and unbalanced-voltage operation conditions and demonstrate the effectiveness of the proposed compensator.« less

Control strategy for a variable-speed wind energy conversion system

NASA Technical Reports Server (NTRS)

Jacob, A.; Veillette, D.; Rajagopalan, V.

1979-01-01

A control concept for a variable-speed wind energy conversion system is proposed, for which a self-exited asynchronous cage generator is used along with a system of thyristor converters. The control loops are the following: (1) regulation of the entrainment speed as function of available mechanical energy by acting on the resistance couple of the asynchronous generator; (2) control of electric power delivered to the asynchronous machine, functioning as a motor, for start-up of the vertical axis wind converter; and (3) limitation of the slip value, and by consequence, of the induction currents in the presence of sudden variations of input parameters.

Synthesis and Thermal Stability of Novel Poly(M-Carborane-Siloxanes) with Various Pendant Groups

NASA Astrophysics Data System (ADS)

Yang, Xiaoxue; Zhao, Yanyan; Wang, Cuicui; Zhang, Xiaoa; Jiang, Shengling; Lyu, Yafei

2017-10-01

Poly(m-carborane-siloxanes) with various pendant groups (P15-P46) were synthesized via polycondensation of m-carborane-containing disilanols (1-4) and highly active bisureidosilanes (5 and 6). The obtained polymers exhibit controlled molecular weight by carefully adjusting the monomer ratio. Standard spectroscopic techniques including FTIR and NMR were utilized to characterize these polymers and satisfactory results were obtained. TGA analysis indicated that the thermal cyclization of polysiloxanes under nitrogen was greatly postponed by the incorporated m-carborane cage, since the siloxane bonds within the main chain were strengthened by the inductive effect of the latter. DSC and FTIR results confirmed that both siloxane unit and carborane cage were oxidized at elevated temperature under air, which contributed to the transformation of the polymers into the mixture of SiO2 and B2O3. Therefore, high char yield was obtained. Besides, the electronic effect of pendant groups greatly influenced the degradation behavior of m-carborane-containing polysiloxanes, having nothing to do with their position. The initial degradation temperature (T d5) increases with varying substituent in the order: CH2CH2CF3 < CH3 ≈ Ph < CH=CH2.

Furnished cage system and hen well-being: Comparative effects of furnished cages and battery cages on behavioral exhibitions in White Leghorn chickens.

PubMed

Pohle, K; Cheng, H-W

2009-08-01

The battery cage system is being banned in the European Union before or by 2012, and the furnished cage system will be the only cage system allowed after 2012. This study was conducted to examine the different effects of caging systems, furnished cages vs. battery cages, on bird behaviors. One hundred ninety-two 1-d-old non-beak-trimmed Hy-Line W-36 White Leghorn chicks were reared using standard management practices in raised wire cages. At 19 wk of age, the birds were randomly assigned into battery cages or furnished cages. The battery cages were commercial wire cages containing 6 birds per cage, providing 645 cm(2) of floor space per birds. The furnished cages had wire floors and solid metal walls, with perches, a dustbathing area, scratch pads, and a nestbox area with a concealment curtain. Based on the company recommendations, 10 birds were housed per cage, providing a stocking density of 610 cm(2) of floor space per bird. Behavioral observations were conducted using the Noldus Observer software package. The birds were observed at 5-min intervals for the entire light period. The birds housed in battery cages had higher posture and behavioral transitions and increased time spent walking and performing exploratory behavior (P < 0.05, 0.01, respectively), which may indicate they were stressed, resulting in restlessness, whereas the birds housed in furnished cages had higher levels of preening (P < 0.05). Preening has been considered as a comfort behavior in birds. These results may suggest that furnished cages may be a favorable alternative system for housing birds by allowing them to perform certain natural behaviors.

Temperature dependence of polyhedral cage volumes in clathrate hydrates

USGS Publications Warehouse

Chakoumakos, B.C.; Rawn, C.J.; Rondinone, A.J.; Stern, L.A.; Circone, S.; Kirby, S.H.; Ishii, Y.; Jones, C.Y.; Toby, B.H.

2003-01-01

The polyhedral cage volumes of structure I (sI) (carbon dioxide, methane, trimethylene oxide) and structure II (sII) (methane-ethane, propane, tetrahydrofuran, trimethylene oxide) hydrates are computed from atomic positions determined from neutron powder-diffraction data. The ideal structural formulas for sI and sII are, respectively, S2L6 ?? 46H2O and S16L???8 ?? 136H2O, where S denotes a polyhedral cage with 20 vertices, L a 24-cage, and L??? a 28-cage. The space-filling polyhedral cages are defined by the oxygen atoms of the hydrogen-bonded network of water molecules. Collectively, the mean cage volume ratio is 1.91 : 1.43 : 1 for the 28-cage : 24-cage : 20-cage, which correspond to equivalent sphere radii of 4.18, 3.79, and 3.37 A??, respectively. At 100 K, mean polyhedral volumes are 303.8, 227.8, and 158.8 A??3 for the 28-cage, 24-cage, and 20-cage, respectively. In general, the 20-cage volume for a sII is larger than that of a sI, although trimethylene oxide is an exception. The temperature dependence of the cage volumes reveals differences between apparently similar cages with similar occupants. In the case of trimethylene oxide hydrate, which forms both sI and sII, the 20-cages common to both structures contract quite differently. From 220 K, the sII 20-cage exhibits a smooth monotonic reduction in size, whereas the sI 20-cage initially expands upon cooling to 160 K, then contracts more rapidly to 10 K, and overall the sI 20-cage is larger than the sII 20-cage. The volumes of the large cages in both structures contract monotonically with decreasing temperature. These differences reflect reoriented motion of the trimethyelene oxide molecule in the 24-cage of sI, consistent with previous spectroscopic and calorimetric studies. For the 20-cages in methane hydrate (sI) and a mixed methane-ethane hydrate (sII), both containing methane as the guest molecule, the temperature dependence of the 20-cage volume in sII is much less than that in sI, but sII is overall larger in volume.

Oral Vaccination of Fish – Antigen Preparations, Uptake, and Immune Induction

PubMed Central

Mutoloki, Stephen; Munang’andu, Hetron Mweemba; Evensen, Øystein

2015-01-01

The oral route offers the most attractive approach of immunization of fish for a number of reasons: the ease of administration of antigens, it is less stressful than parenteral delivery and in principle, it is applicable to small and large sized fish; it also provides a procedure for oral boosting during grow-out periods in cages or ponds. There are, however, not many commercial vaccines available at the moment due to lack of efficacy and challenges associated with production of large quantities of antigens. These are required to stimulate an effective immune response locally and systemically, and need to be protected against degradation before they reach the sites where immune induction occurs. The hostile stomach environment is believed to be particularly important with regard to degradation of antigens in certain species. There is also a poor understanding about the requirements for proper immune induction following oral administration on one side, and the potential for induction of tolerance on the other. To what extent primary immunization via the oral route will elicit both local and systemic responses is not understood in detail. Furthermore, to what extent parenteral delivery will protect mucosal/gut surfaces and vice-versa is also not fully understood. We review the work that has been done on the subject and discuss it in light of recent advances that include mass production of antigens, including the use of plant systems. Different encapsulation techniques that have been developed in the quest to protect antigens against digestive degradation, as well as to target them for appropriate immune induction are also highlighted. PMID:26539192

Effects of separation of resources on behaviour, physical condition and production of laying hens in furnished cages.

PubMed

Shimmura, T; Azuma, T; Eguchi, Y; Uetake, K; Tanaka, T

2009-01-01

1. Based on our previous studies, we designed a medium-sized furnished cage with a dust bath and nest box on both sides of the cage (MFS) and evaluated its usefulness. 2. We used 180 White Leghorn layers. At the age of 17 weeks, the birds were distributed at random into one of the 4 cage designs: conventional cages (CC; 6 cages and 5 hens per cage), small (SF; 6 cages and 5 hens per cage) and medium furnished cages (MFL; 6 cages and 10 hens per cage) with a 'localised' dust bath and nest box on one side of the cage, and MFS (6 cages and 10 hens per cage). The total allocation of resources per bird was similar for all furnished cage designs. Behaviour, physical condition and production were measured in each cage. 3. Moving was more frequent in MFS and MFL than in CC and SF. The proportion of hens performing aggressive pecking and severe feather pecking was higher in MFL than CC and SF. These aggressive interactions occurred frequently in the dust bath area in MFL; however, these tendencies were not found in MFS. Egg production and egg mass were lower in MFL than in SF, while the production in MFS was similar to those in CC and SF. MFS hens laid eggs on the cage floor more often than in MFL. 4. In conclusion, these results demonstrate the possible usefulness of MFS. However, some inconsistent results and ways of improving MFS design were also identified.

Polymers containing borane or carborane cage compounds and related applications

DOEpatents

Bowen, III, Daniel E; Eastwood, Eric A

2013-04-23

Polymers comprising residues of cage compound monomers having at least one polyalkoxy silyl substituent are provided. The cage compound monomers are selected from borane cage compound monomers comprising at least 7 cage atoms and/or carborane cage compound monomers comprising 7 to 11 cage compound monomers. Such polymers can further comprise one or more reactive matrices and/or co-monomers covalently bound with the cage compound monomer residues. Articles of manufacture comprising such polymers are also disclosed.

Effect of housing arrangement on fecal-oral transmission of avian hepatitis E virus in chicken flocks.

PubMed

Liu, Baoyuan; Sun, Yani; Chen, Yiyang; Du, Taofeng; Nan, Yuchen; Wang, Xinjie; Li, Huixia; Huang, Baicheng; Zhang, Gaiping; Zhou, En-Min; Zhao, Qin

2017-09-07

Avian hepatitis E virus (HEV) infection is common in chicken flocks in China, as currently no measures exist to prevent the spread of the disease. In this study, we analyzed the effect of caged versus cage-free housing arrangements on avian HEV transmission. First, 127 serum and 110 clinical fecal samples were collected from 4 chicken flocks including the two arrangements in Shaanxi Province, China and tested for HEV antibodies and/or virus. Concurrently, 36 specific-pathogen-free chickens were divided equally into four experimental living arrangement groups, designated cage-free (Inoculated), caged (Inoculated), cage-free (Negative) and caged (Negative) groups. In caged groups, three cages contained 3 chickens each. Three chickens each from cage-free (Inoculated) and caged (Inoculated) groups (one chicken of each cage) were inoculated by cutaneous ulnar vein with the same dose of avian HEV, respectively. The cage-free (Negative) and caged (Negative) groups served as negative control. Serum and fecal samples were collected at 1 to 7 weeks post-inoculation (wpi) and liver lesions were scored at 7 wpi. The results of serology showed that the avian HEV infection rate (54.10%) of the cage-free chickens was significantly higher than the one (12.12%) for caged chickens (P < 0.05). Also, the rate of detection of avian HEV RNA in the clinical fecal samples was significantly higher in the cage-free (22.80%, 13/57) than caged birds (5.66%, 3/53). Moreover, under experimental conditions, the infected number of uninoculated cage-free chickens (6) was significantly higher than the one for the uninoculated caged birds (2), as evidenced by seroconversion, fecal virus shedding, viremia and gross and microscopic liver lesions. These results suggest that reduction of contact with feces as seen in the caged arrangement of housing chickens can reduce avian HEV transmission. This study provides insights for prevention and control of avian HEV infection in chicken flocks.

Protein cage assembly across multiple length scales.

PubMed

Aumiller, William M; Uchida, Masaki; Douglas, Trevor

2018-05-21

Within the materials science community, proteins with cage-like architectures are being developed as versatile nanoscale platforms for use in protein nanotechnology. Much effort has been focused on the functionalization of protein cages with biological and non-biological moieties to bring about new properties of not only individual protein cages, but collective bulk-scale assemblies of protein cages. In this review, we report on the current understanding of protein cage assembly, both of the cages themselves from individual subunits, and the assembly of the individual protein cages into higher order structures. We start by discussing the key properties of natural protein cages (for example: size, shape and structure) followed by a review of some of the mechanisms of protein cage assembly and the factors that influence it. We then explore the current approaches for functionalizing protein cages, on the interior or exterior surfaces of the capsids. Lastly, we explore the emerging area of higher order assemblies created from individual protein cages and their potential for new and exciting collective properties.

Breathing strategy of the adult horse (Equus caballus) at rest.

PubMed

Koterba, A M; Kosch, P C; Beech, J; Whitlock, T

1988-01-01

To investigate the mechanism underlying the polyphasic airflow pattern of the equine species, we recorded airflow, tidal volum, rib cage and abdominal motion, and the sequence of activation of the diaphragm, intercostal, and abdominal muscles during quiet breathing in nine adult horses standing at rest. In addition, esophageal, abdominal, and transdiaphragmatic pressures were simultaneously recorded using balloon-tipped catheters. Analysis of tidal flow-volume loops showed that, unlike humans, the horse at rest breathes around, rather than from, the relaxed volume of the respiratory system (Vrx). Analysis of the pattern of electromyographic activities and changes in generated pressures during the breathing cycle indicate that the first part of expiration is passive, as in humans, with deflation toward Vrx, but subsequent abdominal activity is responsible for a second phase of expiration: active deflation to below Vrx. From this end-expiratory volume, passive inflation occurs toward Vrx, followed by a second phase of inspiration: active inflation to above Vrx, brought about by inspiratory muscle contraction. Under these conditions the abdominal muscles appear to share the principal pumping duties with the diaphragm. Adoption of this breathing strategy by the horse may relate to its peculiar thoracoabdominal anatomic arrangement and to its very low passive chest wall compliance. We conclude that there is a passive and active phase to both inspiration and expiration due to the coordinated action of the respiratory pump muscles responsible for the resting adult horse's biphasic inspiratory and expiratory airflow pattern. This unique breathing pattern perhaps represents a strategy of minimizing the high elastic work of breathing in this species, at least at resting breathing frequencies.

Microclimatic Variation Within Sleeve Cages Used in Ecological Studies

PubMed Central

Nelson, Lori A.; Rieske, Lynne K.

2014-01-01

Abstract Sleeve cages for enclosing or excluding arthropods are essential components of field studies evaluating trophic interactions. Microclimatic variation in sleeve cages was evaluated to characterize its potential effects on subsequent long-term experiments. Two sleeve cage materials, polyester and nylon, and two cage sizes, 400 and 6000 cm 2 , were tested on eastern hemlock, Tsuga canadensis (L.) Carrière. Temperature and relative humidity inside and outside cages, and the cost and durability of the cage materials, were compared. Long-term effects of the sleeve cages were observed by measuring new growth on T. canadensis branches. The ultimate goal was to identify a material that minimizes bag-induced microclimatic variation. Bagged branches whose microclimates mimic those of surrounding unbagged branches should have minimal effects on plant growth and may prove ideal venues for assessing herbivore and predator behavior under natural conditions. No differences were found in temperature or humidity between caging materials. Small cages had higher average temperatures than large cages, especially in the winter, but this difference was confounded by the fact that small cages were positioned higher in trees than large cages. Differences in plant growth were detected. Eastern hemlock branches enclosed within polyester cages produced fewer new growth tips than uncaged controls. Both polyester and nylon cages reduced the length of new shoot growth relative to uncaged branches. In spite of higher costs, nylon cages were superior to polyester with respect to durability and ease of handling. PMID:25368083

Possible Gems and Ultra-Fine Grained Polyphase Units in Comet Wild 2.

NASA Technical Reports Server (NTRS)

Gainsforth, Z.; Butterworth, A. L.; Jilly-Rehak, C. E.; Westphal, A. J.; Brownlee, D. E.; Joswiak, D.; Ogliore, R. C.; Zolensky, M. E.; Bechtel, H. A.; Ebel, D. S.;

A fully integrated wireless system for intracranial direct cortical stimulation, real-time electrocorticography data transmission, and smart cage for wireless battery recharge.

PubMed

Piangerelli, Marco; Ciavarro, Marco; Paris, Antonino; Marchetti, Stefano; Cristiani, Paolo; Puttilli, Cosimo; Torres, Napoleon; Benabid, Alim Louis; Romanelli, Pantaleo

2014-01-01

Wireless transmission of cortical signals is an essential step to improve the safety of epilepsy procedures requiring seizure focus localization and to provide chronic recording of brain activity for Brain Computer Interface (BCI) applications. Our group developed a fully implantable and externally rechargeable device, able to provide wireless electrocorticographic (ECoG) recording and cortical stimulation (CS). The first prototype of a wireless multi-channel very low power ECoG system was custom-designed to be implanted on non-human primates. The device, named ECOGIW-16E, is housed in a compact hermetically sealed Polyether ether ketone (PEEK) enclosure, allowing seamless battery recharge. ECOGIW-16E is recharged in a wireless fashion using a special cage designed to facilitate the recharge process in monkeys and developed in accordance with guidelines for accommodation of animals by Council of Europe (ETS123). The inductively recharging cage is made up of nylon and provides a thoroughly novel experimental setting on freely moving animals. The combination of wireless cable-free ECoG and external seamless battery recharge solves the problems and shortcomings caused by the presence of cables leaving the skull, providing a safer and easier way to monitor patients and to perform ECoG recording on primates. Data transmission exploits the newly available Medical Implant Communication Service band (MICS): 402-405 MHz. ECOGIW-16E was implanted over the left sensorimotor cortex of a macaca fascicularis to assess the feasibility of wireless ECoG monitoring and brain mapping through CS. With this device, we were able to record the everyday life ECoG signal from a monkey and to deliver focal brain stimulation with movement elicitation.

Heating Pad Performance and Efficacy of 2 Durations of Warming after Isoflurane Anesthesia of Sprague-Dawley Rats (Rattus norvegicus).

PubMed

Zhang, Emily Q; Knight, Cameron G; Pang, Daniel Sj

2017-11-01

Anesthetic agents depress thermoregulatory mechanisms, causing hypothermia within minutes of induction of general anesthesia. The consequences of hypothermia include delayed recovery and increased experimental variability. Even when normothermia is maintained during anesthesia, hypothermia may occur during recovery. The primary aim of this study was to identify an effective warming period for maintaining normothermia during recovery. Adult male (n = 8) and female (n = 9) Sprague-Dawley rats were randomized to 30 min (post30) or 60 min (post60) of warming after recovery from anesthesia. During a 40-min anesthetic period, normothermia (target, 37.5 ± 1.1 °C) was maintained by manual adjustment of an electric heating pad in response to measured rectal temperatures (corrected to estimate core body temperature). Warming was continued in a recovery cage according to treatment group. Rectal temperature was measured for a total of 120 min after anesthesia. Heating pad performance was assessed by measuring temperatures at various sites over its surface. One female rat in the post30 group was excluded from analysis. Normothermia was effectively maintained during and after anesthesia without significant differences between groups. In the post60 group, core temperature was slightly but significantly increased at 90 and 100 min compared with baseline. One rat in each treatment group became hyperthermic (>38.6 °C) during recovery. During recovery, the cage floor temperature required approximately 30 min to stabilize. The heating pad produced heat unevenly over its surface, and measured temperatures frequently exceeded the programmed temperature. Providing 30 min of warming immediately after anesthesia effectively prevented hypothermia in rats. Shorter warming periods may be useful when recovery cages are preheated.

Induced chirality of cage metal complexes switched by their supramolecular and covalent binding.

PubMed

Kovalska, Vladyslava B; Vakarov, Serhii V; Kuperman, Marina V; Losytskyy, Mykhaylo Y; Gumienna-Kontecka, Elzbieta; Voloshin, Yan Z; Varzatskii, Oleg A

2018-01-23

An ability of the ribbed-functionalized iron(ii) clathrochelates to induce a CD output in interactions with a protein, covalent bonding or supramolecular interactions with a low-molecular-weight chiral inductor, was discovered. The interactions of CD inactive, carboxyl-terminated iron(ii) clathrochelates with serum albumin induced their molecular asymmetry, causing an appearance of strong CD signals in the range of 350-600 nm, whereas methyl ester and amide clathrochelate derivatives remained almost CD inactive. The CD spectra of carboxyl-terminated clathrochelates on supramolecular interactions or covalent bonding with (R)-(+)-1-phenylethylamine gave a substantially lower CD output than with albumin, affected by both the solvent polarity and the isomerism of clathrochelate's ribbed substituents. In supramolecular assemblies, the bands were most intensive for ortho-substituted carboxyl-terminated clathrochelates. The ortho- and meta-phenylethylamide cage complexes in tetrachloromethane inverted the signs of their CD bands compared with those in acetonitrile. It was suggested that the tris-dioximate metal clathrochelates possess a Russian doll-like molecular system. Because of the distorted TP-TAP geometry, their coordination polyhedron had no inversion centre and possessed an inherent chirality together with the equiprobability of its left(Λ)- and right(Δ)-handle twists. The selective fixation of one of these C 3 -distorted conformations resulted in the appearance of the CD signal in the range of their visible metal-to-ligand charge transfer bands. Calculations by DFT methods were used to illustrate the possible conformations of the macrobicyclic molecules, as well as the intramolecular interactions between the cage framework and optically active distal substituents responsible for the chirality induction of the metal-centred coordination polyhedra.

Computational comparison of three posterior lumbar interbody fusion techniques by using porous titanium interbody cages with 50% porosity.

PubMed

Lee, Yung-Heng; Chung, Chi-Jen; Wang, Chih-Wei; Peng, Yao-Te; Chang, Chih-Han; Chen, Chih-Hsien; Chen, Yen-Nien; Li, Chun-Ting

2016-04-01

This study investigated the biomechanical response of porous cages and lumbar spine segments immediately after surgery and after bone fusion, in addition to the long-term effects of various posterior lumbar interbody fusion (PLIF) techniques, by using the finite element method. Lumbar L3-L4 models based on three PLIF techniques (a single cage at the center of the intervertebral space, a single cage half-anterior to the intervertebral space, and two cages bilateral to the intervertebral space) with and without bone ingrowth were used to determine the biomechanical response of porous cages and lumbar segments instrumented with porous titanium cages (cage porosity=50%, pore diameter=1mm). The results indicated that bone fusion enhanced the stability of the lumbar segments with porous cages without any posterior instrumentation and reduced the peak von Mises stress in the cortical bones and porous cages. Two cages placed bilateral to the intervertebral space achieved the highest structural stability in the lumbar segment and lowest von Mises stress in the cages under both bone fusion conditions. Under identical loading (2-Nm), the range of motion in the single cage at the center of the intervertebral space with bone fusion decreased by 11% (from 1.18° to 1.05°) during flexion and by 66.5% (from 4.46° to 1.5°) during extension in the single cage half-anterior to the intervertebral space with bone fusion compared with no-fusion models. Thus, two porous titanium cages with 50% porosity can achieve high stability of a lumbar segment with PLIF. If only one cage is available, placing the cage half-anterior to the intervertebral space is recommended for managing degenerated lumbar segments. Copyright © 2016 Elsevier Ltd. All rights reserved.

Do position and size matter? An analysis of cage and placement variables for optimum lordosis in PLIF reconstruction.

PubMed

Landham, Priyan R; Don, Angus S; Robertson, Peter A

2017-11-01

To examine monosegmental lordosis after posterior lumbar interbody fusion (PLIF) surgery and relate lordosis to cage size, shape, and placement. Eighty-three consecutive patients underwent single-level PLIF with paired identical lordotic cages involving a wide decompression and bilateral facetectomies. Cage parameters relating to size (height, lordosis, and length) and placement (expressed as a ratio relative to the length of the inferior vertebral endplate) were recorded. Centre point ratio (CPR) was the distance to the centre of both cages and indicated mean position of both cages. Posterior gap ratio (PGR) was the distance to the most posterior cage and indicated position and cage length indirectly. Relationships between lordosis and cage parameters were explored. Mean lordosis increased by 5.98° (SD 6.86°). The cages used varied in length from 20 to 27 mm, in lordosis from 10° to 18°, and in anterior cage height from 10 to 17 mm. The mean cage placement as determined by CPR was 0.54 and by PGR was 0.16. The significant correlations were: both CPR and PGR with lordosis gain at surgery (r = 0.597 and 0.537, respectively, p < 0.001 both), cage lordosis with the final lordosis (r = 0.234, p < 0.05), and anterior cage height was negatively correlated with a change in lordosis (r = -0.297, p < 0.01). Cage size, shape, and position, in addition to surgical technique, determine lordosis during PLIF surgery. Anterior placement with sufficient "clear space" behind the cages is recommended. In addition, cages should be of moderate height and length, so that they act as an effective pivot for lordosis.

Characterization of a new caged proton capable of inducing large pH jumps.

PubMed Central

Barth, Andreas; Corrie, John E T

2002-01-01

A new caged proton, 1-(2-nitrophenyl)ethyl sulfate (caged sulfate), is characterized by infrared spectroscopy and compared with a known caged, proton 2-hydroxyphenyl 1-(2-nitrophenyl)ethyl phosphate (caged HPP). In contrast to caged HPP, caged sulfate can induce large pH jumps and protonate groups that have pK values as low as 2.2. The photolysis mechanism of caged sulfate is analogous to that of P(3)-[1-(2-nitrophenyl)ethyl] ATP (caged ATP), and the photolysis efficiency is similar. The utility of this new caged compound for biological studies was demonstrated by its ability to drive the acid-induced conformational change of metmyoglobin. This transition from the native conformation to a partially unfolded form takes place near pH 4 and was monitored by near-UV absorption spectroscopy. PMID:12414718

The challenge of pelvic discontinuity: cup-cage reconstruction does better than conventional cages in mid-term.

PubMed

Abolghasemian, M; Tangsaraporn, S; Drexler, M; Barbuto, R; Backstein, D; Safir, O; Kuzyk, P; Gross, A

2014-02-01

The use of ilioischial cage reconstruction for pelvic discontinuity has been replaced by the Trabecular Metal (Zimmer, Warsaw, Indiana) cup-cage technique in our institution, due to the unsatisfactory outcome of using a cage alone in this situation. We report the outcome of 26 pelvic discontinuities in 24 patients (20 women and four men, mean age 65 years (44 to 84)) treated by the cup-cage technique at a mean follow-up of 82 months (12 to 113) and compared them with a series of 19 pelvic discontinuities in 19 patients (18 women and one man, mean age 70 years (42 to 86)) treated with a cage at a mean follow-up of 69 months (1 to 170). The clinical and radiological outcomes as well as the survivorship of the groups were compared. In all, four of the cup-cage group (15%) and 13 (68%) of the cage group failed due to septic or aseptic loosening. The seven-year survivorship was 87.2% (95% confidence interval (CI) 71 to 103) for the cup-cage group and 49.9% (95% CI 15 to 84) for the cage-alone group (p = 0.009). There were four major complications in the cup-cage group and nine in the cage group. Radiological union of the discontinuity was found in all successful cases in the cup-cage group and three of the successful cage cases. Three hips in the cup-cage group developed early radiological migration of the components, which stabilised with a successful outcome. Cup-cage reconstruction is a reliable technique for treating pelvic discontinuity in mid-term follow-up and is preferred to ilioischial cage reconstruction. If the continuity of the bone graft at the discontinuity site is not disrupted, early migration of the components does not necessarily result in failure.

Reproductive Performance of Mice in Disposable and Standard Individually Ventilated Cages

PubMed Central

Ferguson, Danielle R; Bailey, Michele M

2013-01-01

This study assessed the reproductive performance of mice housed in 2 types of individually ventilated caging systems. Breeding pairs from 48 female and 24 male mice of 3 established transgenic mouse breeding colonies were placed in either a standard or disposable ventilated caging system. For 3 breeding cycles, the number of pups born, pup survival rate to weaning, time interval between litters, and pup weights were monitored for each breeding pair. Disposable and standard cages were maintained in the same location during breeding. Environmental parameters included intracage temperature, humidity, and ammonia and carbon dioxide levels and room light intensity and sound. Overall, 776 offspring were produced. Breeding performance did not differ significantly between the 2 cage types. By 11 wk of age, the weights of pups from both cage types were equivalent. The intracage temperature was 1.1 °F warmer and light intensity at the site of the nest was 34 lx dimmer in disposable cages than in standard caging. The difference in lighting likely was due to nest location; the nests in the disposable cages were at the back of the cages and away from the anterior air supply, whereas in standard caging, nests were at the front of the cages, with the air supply at the rear. Under these husbandry conditions, mice housed in disposable caging systems have comparable breeding performance to those housed in standard individually ventilated cages. PMID:23849403

Effects of wind speed on aerosol spray penetration in adult mosquito bioassay cages.

PubMed

Hoffmann, W Clint; Fritz, Bradley K; Farooq, Muhammad; Cooperband, Miriam F

2008-09-01

Bioassay cages are commonly used to assess efficacy of insecticides against adult mosquitoes in the field. To correlate adult mortality readings to insecticidal efficacy and/or spray application parameters properly, it is important to know how the cage used in the bioassay interacts with the spray cloud containing the applied insecticide. This study compared the size of droplets, wind speed, and amount of spray material penetrating cages and outside of cages in a wind tunnel at different wind speeds. Two bioassay cages, Center for Medical, Agricultural and Veterinary Entomology (CMAVE) and Circle, were evaluated. The screen materials used on these cages reduced the size of droplets, wind speed, and amount of spray material inside the cages as compared to the spray cloud and wind velocity outside of the cages. When the wind speed in the dispersion tunnel was set at 0.6 m/sec (1.3 mph), the mean wind speed inside of the CMAVE Bioassay Cage and Circle Cage was 0.045 m/sec (0.10 mph) and 0.075 m/sec (0.17 mph), respectively. At air velocities of 2.2 m/sec (4.9 mph) in the dispersion tunnel, the mean wind speed inside of the CMAVE Bioassay Cage and Circle Cage was 0.83 m/sec (1.86 mph) and 0.71 m/sec (1.59 mph), respectively. Consequently, there was a consistent 50-70% reduction of spray material penetrating the cages compared to the spray cloud that approached the cages. These results provide a better understanding of the impact of wind speed, cage design, and construction on ultra-low-volume spray droplets.

Long-term effects of placing one or two cages in instrumented posterior lumbar interbody fusion.

PubMed

Zhang, Mingzheng; Pu, Fang; Xu, Liqiang; Zhang, Linlin; Yao, Jie; Li, Deyu; Wang, Yu; Fan, Yubo

2016-06-01

Posterior lumbar interbody fusion (PLIF) is an established surgical procedure for spine stabilization after the removal of an intervertebral disc. Researches have shown that inserting a single oblique cage has a similar immediate effect to coupled cages, and it has been proposed that single-cage PLIF is a useful alternative to traditional two-cage PLIF. However, it is not clear whether placing one or two cages represents the best choice for long-term fusion. The aim of this study is to examine how cage placement affects bone remodeling after PLIF surgery, and how this consequently impacts the long-term fusion process. A finite element model of a L3-L4 lumbar spine with PLIF was developed. The spinal segment was modeled with a partial laminectomy and a discectomy with partial facetectomy, and implanted with posterior pedicle screws. Two models were analyzed, one with coupled parallel cages and one with a single oblique cage. Adaptive bone remodeling was simulated according to Huiskes' criterion. The results showed that in the initial state prior to any bone remodeling, cage stress, cage subsidence and cage dislodgement in the single cage model were all greater than in the coupled cage model. In the final state after significant bone remodeling had taken place, these parameters had decreased in both models and the differences between the two models were reduced. Also, the single cage model demonstrated superior bone development in the bone graft when placed under a constant 400 N axial compressive load. Based on the long-term results, instrumented PLIF with a single cage could also be encouraged in clinical practice.

Cyanobacterial composition of microbial mats from an Australian thermal spring: a polyphasic evaluation.

PubMed

McGregor, Glenn B; Rasmussen, J Paul

2008-01-01

Cyanobacterial composition of microbial mats from an alkaline thermal spring issuing at 43-71 degrees C from tropical north-eastern Australia are described using a polyphasic approach. Eight genera and 10 species from three cyanobacterial orders were identified based on morphological characters. These represented taxa previously known as thermophilic from other continents. Ultrastructural analysis of the tower mats revealed two filamentous morphotypes contributed the majority of the biomass. Both types had ultrastructural characteristics of the family Pseudanabaenaceae. DNA extracts were made from sections of the tentaculiform towers and the microbial community analysed by 16S cyanobacteria-specific PCR and denaturing-gradient gel electrophoresis. Five significant bands were identified and sequenced. Two bands clustered closely with Oscillatoria amphigranulata isolated from New Zealand hot springs; one unique phylotype had only moderate similarity to a range of Leptolyngbya species; and one phylotype was closely related to a number of Geitlerinema species. Generally the approaches yielded complementary information, however the results suggest that species designation based on morphological and ultrastructural criteria alone often fails to recognize their true phylogenetic position. Conversely some molecular techniques may fail to detect rare taxa suggesting that the widest possible suite of techniques be applied when conducting analyses of cyanobacterial diversity of natural populations. This is the first polyphasic evaluation of thermophilic cyanobacterial communities from the Australian continent.

Polyphasic taxonomy of the genus Shewanella and description of Shewanella oneidensis sp. nov

NASA Technical Reports Server (NTRS)

Venkateswaran, K.; Moser, D. P.; Dollhopf, M. E.; Lies, D. P.; Saffarini, D. A.; MacGregor, B. J.; Ringelberg, D. B.; White, D. C.; Nishijima, M.; Sano, H.;

A novel test cage with an air ventilation system as an alternative to conventional cages for the efficacy testing of mosquito repellents.

PubMed

Obermayr, U; Rose, A; Geier, M

2010-11-01

We have developed a novel test cage and improved method for the evaluation of mosquito repellents. The method is compatible with the United States Environmental Protection Agency, 2000 draft OPPTS 810.3700 Product Performance Test Guidelines for Testing of Insect Repellents. The Biogents cages (BG-cages) require fewer test mosquitoes than conventional cages and are more comfortable for the human volunteers. The novel cage allows a section of treated forearm from a volunteer to be exposed to mosquito probing through a window. This design minimizes residual contamination of cage surfaces with repellent. In addition, an air ventilation system supplies conditioned air to the cages after each single test, to flush out and prevent any accumulation of test substances. During biting activity tests, the untreated skin surface does not receive bites because of a screen placed 150 mm above the skin. Compared with the OPPTS 810.3700 method, the BG-cage is smaller (27 liters, compared with 56 liters) and contains 30 rather than hundreds of blood-hungry female mosquitoes. We compared the performance of a proprietary repellent formulation containing 20% KBR3023 with four volunteers on Aedes aegypti (L.) (Diptera: Culicidae) in BG- and conventional cages. Repellent protection time was shorter in tests conducted with conventional cages. The average 95% protection time was 4.5 +/- 0.4 h in conventional cages and 7.5 +/- 0.6 h in the novel BG-cages. The protection times measured in BG-cages were more similar to the protection times determined with these repellents in field tests.

Influence of 5 Different Caging Types and the Use of Cage-Changing Stations on Mouse Allergen Exposure

PubMed Central

Feistenauer, Susan; Sander, Ingrid; Schmidt, Jörg; Zahradnik, Eva; Raulf, Monika; Brielmeier, Markus

2014-01-01

Animal allergens constitute a serious health risk in laboratory animal facilities. To assess possibilities for allergen reduction by technical and organizational measures, we studied personnel exposure to mouse urinary aeroallergens in an animal facility with a holding capacity of 30,000 cages. Short-term (2 h) and intermediate-term (12 h) stationary samples (n = 107) and short-term (2 h) personnel samples (n = 119) were collected on polytetrafluorethylene filters by using air pumps. Long-term (14 d) stationary dust samples containing airborne allergens (n = 165) were collected with electrostatic dust fall collectors (EDC). Mouse allergens were quantified by ELISA. Personnel samples were collected during bedding disposal and refilling of clean cages as well as during cage changing with and without use of cage-changing station. Animal rooms were equipped with either open cages, cages with a soft filter top, cages with a rigid filter top (static microisolation caging), or with individually ventilated cages (IVC) with either a sealed or nonsealed lid, each in positive- or negative-pressure mode. Highest personnel allergen exposure was detected during cage change and emptying of soiled cages. Allergen concentrations were lowest in rooms with sealed IVC under positive or negative pressure, with unsealed IVC under negative pressure, and with static microisolation caging. The use of cage-changing stations and a vacuum bedding-disposal system reduced median personnel exposures 14- to 25-fold, respectively. Using sealed IVC and changing stations minimized allergen exposure, indicating that state-of-the-art equipment reduces exposure to mouse allergens and decreases health risks among animal facility personnel. PMID:25199090

Improved efficiency and precise temperature control of low-frequency induction-heating pure iron vapor source on ECR ion source

NASA Astrophysics Data System (ADS)

Kato, Y.; Takenaka, T.; Yano, K.; Kiriyama, R.; Kurisu, Y.; Nozaki, D.; Muramatsu, M.; Kitagawa, A.; Uchida, T.; Yoshida, Y.; Sato, F.; Iida, T.

2012-11-01

Multiply charged ions to be used prospectively are produced from solid pure material in an electron cyclotron resonance ion source (ECRIS). Recently a pure iron source is also required for the production of caged iron ions in the fullerene in order to control cells in vivo in bio-nano science and technology. We adopt directly heating iron rod by induction heating (IH) because it has non-contact with insulated materials which are impurity gas sources. We choose molybdenum wire for the IH coils because it doesn't need water cooling. To improve power efficiency and temperature control, we propose to the new circuit without previously using the serial and parallel dummy coils (SPD) for matching and safety. We made the circuit consisted of inductively coupled coils which are thin-flat and helix shape, and which insulates the IH power source from the evaporator. This coupling coils circuit, i.e. insulated induction heating coil transformer (IHCT), can be move mechanically. The secondary current can be adjusted precisely and continuously. Heating efficiency by using the IHCT is much higher than those of previous experiments by using the SPD, because leakage flux is decreased and matching is improved simultaneously. We are able to adjust the temperature in heating the vapor source around melting point. And then the vapor pressure can be controlled precisely by using the IHCT. We can control ±10K around 1500°C by this method, and also recognize to controlling iron vapor flux experimentally in the extreme low pressures. Now we come into next stage of developing induction heating vapor source for materials with furthermore high temperature melting points above 2000K with the IHCT, and then apply it in our ECRIS.

Flexibility and fatigue evaluation of oblique as compared with anterior lumbar interbody cages with integrated endplate fixation.

PubMed

Freeman, Andrew L; Camisa, William J; Buttermann, Glenn R; Malcolm, James R

2016-01-01

This study was undertaken to quantify the in vitro range of motion (ROM) of oblique as compared with anterior lumbar interbody devices, pullout resistance, and subsidence in fatigue. Anterior and oblique cages with integrated plate fixation (IPF) were tested using lumbar motion segments. Flexibility tests were conducted on the intact segments, cage, cage + IPF, and cage + IPF + pedicle screws (6 anterior, 7 oblique). Pullout tests were then performed on the cage + IPF. Fatigue testing was conducted on the cage + IPF specimens for 30,000 cycles. No ROM differences were observed in any test group between anterior and oblique cage constructs. The greatest reduction in ROM was with supplemental pedicle screw fixation. Peak pullout forces were 637 ± 192 N and 651 ± 127 N for the anterior and oblique implants, respectively. The median cage subsidence was 0.8 mm and 1.4 mm for the anterior and oblique cages, respectively. Anterior and oblique cages similarly reduced ROM in flexibility testing, and the integrated fixation prevented device displacement. Subsidence was minimal during fatigue testing, most of which occurred in the first 2500 cycles.

Ligand-linked phase changes in a biological system: applications to sickle cell hemoglobin.

PubMed Central

Wyman, J; Gill, S J

1980-01-01

Polyphasic linkage is a close analog of the allosteric and polysteric linkages shown by many biological macromolecules. Like them, it gives rise to both homotropic and heterotropic effects. It is governed by a group of linkage potentials applicable to each separate phase and also, subject to certain conditions, by a group of lower order applicable to the whole system, globally. A good example of polyphasic linkage is provided by sickle cell hemoglobin which, under suitable conditions and subject to control by oxygen, precipitates out of solution to form what appear to be microtubules. This is but one instance of the way in which macromolecular assembly and the formation of subcellular structures generally can be regulated by various small molecules acting as ligands. PMID:6933555

Comparison of Expandable and Fixed Interbody Cages in a Human Cadaver Corpectomy Model: Fatigue Characteristics.

PubMed

Pekmezci, Murat; Tang, Jessica A; Cheng, Liu; Modak, Ashin; McClellan, Robert T; Buckley, Jenni M; Ames, Christopher P

2016-11-01

In vitro cadaver biomechanics study. The goal of this study is to compare the in situ fatigue life of expandable versus fixed interbody cage designs. Expandable cages are becoming more popular, in large part, due to their versatility; however, subsidence and catastrophic failure remain a concern. This in vitro analysis investigates the fatigue life of expandable and fixed interbody cages in a single level human cadaver corpectomy model by evaluating modes of subsidence of expandable and fixed cages as well as change in stiffness of the constructs with cyclic loading. Nineteen specimens from 10 human thoracolumbar spines (T10-L2, L3-L5) were biomechanically evaluated after a single level corpectomy that was reconstructed with an expandable or fixed cage and anterior dual rod instrumentation. All specimens underwent 98 K cycles to simulate 3 months of postoperative weight bearing. In addition, a third group with hyperlordotic cages was used to simulate catastrophic failure that is observed in clinical practice. Three fixed and 2 expandable cages withstood the cyclic loading despite perfect sagittal and coronal plane fitting of the endcaps. The majority of the constructs settled in after initial subsidence. The catastrophic failures that were observed in clinical practice could not be reproduced with hyperlordotic cages. However, all cages in this group subsided, and 60% resulted in endplate fractures during deployment of the cage. Despite greater surface contact area, expandable cages have a trend for higher subsidence rates when compared with fixed cages. When there is edge loading as in the hyperlordotic cage scenario, there is a higher risk of subsidence and intraoperative fracture during deployment of expandable cages.

[Experiences with cage combinations for guinea pigs].

PubMed

von Zychlinski, J

1989-01-01

Special cage units described in 1982 for guinea pigs have been used either as cages for small groups of breeding animals or for caging of growing animals. By using these cages the following advantages have been noted; the cage size can be adapted to number, age and body weight of the animals; aggression and panic are avoided by corners, walls and tunnels; economic use of breeding males by mating with more females.

Ammonia and Carbon Dioxide Concentrations in Disposable and Reusable Ventilated Mouse Cages

PubMed Central

Silverman, Jerald; Bays, David W; Cooper, Sheldon F; Baker, Stephen P

2008-01-01

This study compares resuable and disposable individually ventilated mouse cages in terms of the formation of intracage CO2 and NH3. Crl:CD-1(ICR) female mice were placed in either disposable or reusable ventilated cages in a positive pressure animal rack. Intracage CO2 and NH3 were measured once daily for 9 d; temperature and relative humidity were monitored for the first 7 d. Results indicated higher CO2 levels in the rear of the disposable cages and in the front of the reusable cages. This pattern corresponded to where the mice tended to congregate. However, CO2 concentrations did not differ significantly between the 2 cage types. Average CO2 levels in both cage types never exceeded approximately 3000 ppm. Intracage NH3 began to rise in the reusable cages on day 4, reached approximately 50 ppm by day 5 and by day 9 was greater than 150 ppm at the cages' rear sampling port while remaining at approximately 70 ppm at the front sampling port. Intracage NH3 levels in the disposable cages remained less than or equal to 3.2 ppm. Intracage temperature and relative humidity were approximately the same in both cage types. We concluded that the disposable ventilated cage performed satisfactorily under the conditions of the study. PMID:18351723

Effects of Furnished Cage Type on Behavior and Welfare of Laying Hens.

PubMed

Li, Xiang; Chen, Donghua; Li, Jianhong; Bao, Jun

2016-06-01

This study was conducted to compare the effects of layout of furniture (a perch, nest, and sandbox) in cages on behavior and welfare of hens. Two hundred and sixteen Hyline Brown laying hens were divided into five groups (treatments) with four replicates per group: small furnished cages (SFC), medium furnished cages type I (MFC-I), medium furnished cages type II (MFC-II), and medium furnished cages type III (MFC-III) and conventional cages (CC). The experiment started at 18 week of age and finished at 52 week of age. Hens' behaviors were filmed during the following periods: 8:00 to 10:00; 13:00 to 14:00; 16:00 to 17:00 on three separate days and two hens from each cage were measured for welfare parameters at 50 wk of age. The results showed that feeding and laying of all hens showed no effect by cage type (p>0.05), and the hens in the furnished cages had significantly lower standing and higher walking than CC hens (p<0.05). The birds in MFC-III had significant higher preening, scratching and feather-pecking behavior than in the other cages (p<0.05). No difference in nesting behavior was found in the hens between the furnished cages (p>0.05). The hens in MFC-I, -II, and -III showed a significant higher socializing behavior than SFC and CC (p<0.05). The lowest perching was for the hens in SFC and the highest perching found for the hens in MFC-III. Overall, the hens in CC showed poorer welfare conditions than the furnished cages, in which the feather condition score, gait score and tonic immobility duration of the hens in CC was significantly higher than SFC, MFC-I, MFC-II, and MFC-III (p<0.05). In conclusion, the furnished cage design affected both behavior and welfare states of hens. Overall, MFC-III cage design was better than SFC, MFC-I, and MFC-II cage designs.

Effects of Furnished Cage Type on Behavior and Welfare of Laying Hens

PubMed Central

Li, Xiang; Chen, Donghua; Li, Jianhong; Bao, Jun

2016-01-01

This study was conducted to compare the effects of layout of furniture (a perch, nest, and sandbox) in cages on behavior and welfare of hens. Two hundred and sixteen Hyline Brown laying hens were divided into five groups (treatments) with four replicates per group: small furnished cages (SFC), medium furnished cages type I (MFC-I), medium furnished cages type II (MFC-II), and medium furnished cages type III (MFC-III) and conventional cages (CC). The experiment started at 18 week of age and finished at 52 week of age. Hens’ behaviors were filmed during the following periods: 8:00 to 10:00; 13:00 to 14:00; 16:00 to 17:00 on three separate days and two hens from each cage were measured for welfare parameters at 50 wk of age. The results showed that feeding and laying of all hens showed no effect by cage type (p>0.05), and the hens in the furnished cages had significantly lower standing and higher walking than CC hens (p<0.05). The birds in MFC-III had significant higher preening, scratching and feather-pecking behavior than in the other cages (p<0.05). No difference in nesting behavior was found in the hens between the furnished cages (p>0.05). The hens in MFC-I, −II, and −III showed a significant higher socializing behavior than SFC and CC (p<0.05). The lowest perching was for the hens in SFC and the highest perching found for the hens in MFC-III. Overall, the hens in CC showed poorer welfare conditions than the furnished cages, in which the feather condition score, gait score and tonic immobility duration of the hens in CC was significantly higher than SFC, MFC-I, MFC-II, and MFC-III (p<0.05). In conclusion, the furnished cage design affected both behavior and welfare states of hens. Overall, MFC-III cage design was better than SFC, MFC-I, and MFC-II cage designs. PMID:26954171

One and two hydrogen molecules in the large cage of the structure II clathrate hydrate: quantum translation-rotation dynamics close to the cage wall.

PubMed

Sebastianelli, Francesco; Xu, Minzhong; Kanan, Dalal K; Bacić, Zlatko

2007-07-19

We have performed a rigorous theoretical study of the quantum translation-rotation (T-R) dynamics of one and two H2 and D2 molecules confined inside the large hexakaidecahedral (5(12)6(4)) cage of the sII clathrate hydrate. For a single encapsulated H2 and D2 molecule, accurate quantum five-dimensional calculations of the T-R energy levels and wave functions are performed that include explicitly, as fully coupled, all three translational and the two rotational degrees of freedom of the hydrogen molecule, while the cage is taken to be rigid. In addition, the ground-state properties, energetics, and spatial distribution of one and two p-H2 and o-D2 molecules in the large cage are calculated rigorously using the diffusion Monte Carlo method. These calculations reveal that the low-energy T-R dynamics of hydrogen molecules in the large cage are qualitatively different from that inside the small cage, studied by us recently. This is caused by the following: (i) The large cage has a cavity whose diameter is about twice that of the small cage for the hydrogen molecule. (ii) In the small cage, the potential energy surface (PES) for H2 is essentially flat in the central region, while in the large cage the PES has a prominent maximum at the cage center, whose height exceeds the T-R zero-point energy of H2/D2. As a result, the guest molecule is excluded from the central part of the large cage, its wave function localized around the off-center global minimum. Peculiar quantum dynamics of the hydrogen molecule squeezed between the central maximum and the cage wall manifests in the excited T-R states whose energies and wave functions differ greatly from those for the small cage. Moreover, they are sensitive to the variations in the hydrogen-bonding topology, which modulate the corrugation of the cage wall.

Sagittal Plane Correction Using the Lateral Transpsoas Approach: A Biomechanical Study on the Effect of Cage Angle and Surgical Technique on Segmental Lordosis.

PubMed

Melikian, Rojeh; Yoon, Sangwook Tim; Kim, Jin Young; Park, Kun Young; Yoon, Caroline; Hutton, William

2016-09-01

Cadaveric biomechanical study. To determine the degree of segmental correction that can be achieved through lateral transpsoas approach by varying cage angle and adding anterior longitudinal ligament (ALL) release and posterior element resection. Lordotic cage insertion through the lateral transpsoas approach is being used increasingly for restoration of sagittal alignment. However, the degree of correction achieved by varying cage angle and ALL release and posterior element resection is not well defined. Thirteen lumbar motion segments between L1 and L5 were dissected into single motion segments. Segmental angles and disk heights were measured under both 50 N and 500 N compressive loads under the following conditions: intact specimen, discectomy (collapsed disk simulation), insertion of parallel cage, 10° cage, 30° cage with ALL release, 30° cage with ALL release and spinous process (SP) resection, 30° cage with ALL release, SP resection, facetectomy, and compression with pedicle screws. Segmental lordosis was not increased by either parallel or 10° cages as compared with intact disks, and contributed small amounts of lordosis when compared with the collapsed disk condition. Placement of 30° cages with ALL release increased segmental lordosis by 10.5°. Adding SP resection increased lordosis to 12.4°. Facetectomy and compression with pedicle screws further increased lordosis to approximately 26°. No interventions resulted in a decrease in either anterior or posterior disk height. Insertion of a parallel or 10° cage has little effect on lordosis. A 30° cage insertion with ALL release resulted in a modest increase in lordosis (10.5°). The addition of SP resection and facetectomy was needed to obtain a larger amount of correction (26°). None of the cages, including the 30° lordotic cage, caused a decrease in posterior disk height suggesting hyperlordotic cages do not cause foraminal stenosis. N/A.

Real time PI-backstepping induction machine drive with efficiency optimization.

PubMed

Farhani, Fethi; Ben Regaya, Chiheb; Zaafouri, Abderrahmen; Chaari, Abdelkader

2017-09-01

This paper describes a robust and efficient speed control of a three phase induction machine (IM) subjected to load disturbances. First, a Multiple-Input Multiple-Output (MIMO) PI-Backstepping controller is proposed for a robust and highly accurate tracking of the mechanical speed and rotor flux. Asymptotic stability of the control scheme is proven by Lyapunov Stability Theory. Second, an active online optimization algorithm is used to optimize the efficiency of the drive system. The efficiency improvement approach consists of adjusting the rotor flux with respect to the load torque in order to minimize total losses in the IM. A dSPACE DS1104 R&D board is used to implement the proposed solution. The experimental results released on 3kW squirrel cage IM, show that the reference speed as well as the rotor flux are rapidly achieved with a fast transient response and without overshoot. A good load disturbances rejection response and IM parameters variation are fairly handled. The improvement of drive system efficiency reaches up to 180% at light load. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

A review and comparison of fault detection and diagnosis methods for squirrel-cage induction motors: State of the art.

PubMed

Liu, Yiqi; Bazzi, Ali M

2017-09-01

Preventing induction motors (IMs) from failure and shutdown is important to maintain functionality of many critical loads in industry and commerce. This paper provides a comprehensive review of fault detection and diagnosis (FDD) methods targeting all the four major types of faults in IMs. Popular FDD methods published up to 2010 are briefly introduced, while the focus of the review is laid on the state-of-the-art FDD techniques after 2010, i.e. in 2011-2015 and some in 2016. Different FDD methods are introduced and classified into four categories depending on their application domains, instead of on fault types like in many other reviews, to better reveal hidden connections and similarities of different FDD methods. Detailed comparisons of the reviewed papers after 2010 are given in tables for fast referring. Finally, a dedicated discussion session is provided, which presents recent developments, trends and remaining difficulties regarding to FDD of IMs, to inspire novel research ideas and new research possibilities. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Nasal Histopathology and Intracage Ammonia Levels in Female Groups and Breeding Mice Housed in Static Isolation Cages

PubMed Central

Mexas, Angela M; Brice, Angela K; Caro, Adam C; Hillanbrand, Troy S

2015-01-01

Many factors influence ammonia levels in rodent cages, and high intracage ammonia has been associated with specific types of abnormal nasal pathology in mice. The use of autoclaved corncob bedding and the maintenance of low room humidity reduce the accumulation of ammonia in mouse cages. However, there are no engineering standards that define the limits of ammonia exposure for mice housed in static isolation cages. Regulatory guidance indicates that solid bottom cages must be sanitized at least weekly and that cage components in direct contact with animals must be sanitized at least every 2 wk. Common practice is to replace the bottoms and bedding of static isolation cages once weekly. To determine whether changing static isolation cages once weekly is an appropriate performance standard for mice, we prospectively evaluated the relationship between ammonia levels, nasal histopathology, and housing densities in various grouping strategies of mice housed in static isolation cages. Here, we report that the average nasal pathology score per cage and intracage ammonia levels were correlated, but nasal pathology scores did not differ among mice housed in breeding pairs, breeding trios, or female groups. In light of ammonia levels and histopathology scores as performance standards, these results suggest that a weekly cage-change frequency for static isolation cages does not result in adverse effects. Our results provide evidence to support current practices in the use of static isolation cages for housing laboratory mice in modern vivaria. PMID:26424245

Disparities in Ammonia, Temperature, Humidity, and Airborne Particulate Matter between the Micro-and Macroenvironments of Mice in Individually Ventilated Caging

PubMed Central

Rosenbaum, Matthew D; VandeWoude, Susan; Volckens, John; Johnson, Thomas E

2010-01-01

Animal room environmental parameters typically are monitored with the assumption that the environment within the cage closely mirrors the room environment. This study evaluated that premise by examining macro- (room) and microenvironmental (cage) parameters in individually ventilated cages housing mice with variable amounts of bedding over a period of 17 d without cage changes. Intracage ammonia levels remained within recommended human guidelines but were higher than room levels, confirming that microisolation caging is efficient at preventing ammonia generated from animal waste from escaping into the room. Humidity and temperature within cages were consistently higher than room levels. Particles in the room predominantly consisted of fine particles (diameter less than 2.5 µm), presumably from the ambient atmosphere; some of these particles were found in the cage microenvironment. In addition, mouse activity within cages produced larger particles, and these particles contributed to substantially higher aerosol mass concentrations within the cage. These findings demonstrate that, although cage and room environmental parameters differ, knowledge of room environmental conditions can be used to predict certain conditions within the cage. This association is relevant in that typical animal care standard operating procedures rely on room measurements, not intracage measurements, which arguably are more important for assessing animal welfare. Further, location and ambient climate can influence particle concentrations in the room, and consequently within the animal cage, suggesting local weather patterns and air quality may account for variability among studies conducted at sites that are geographically divergent. PMID:20353692

Elimination of Subsidence with 26-mm-Wide Cages in Extreme Lateral Interbody Fusion.

PubMed

Lang, Gernot; Navarro-Ramirez, Rodrigo; Gandevia, Lena; Hussain, Ibrahim; Nakhla, Jonathan; Zubkov, Micaella; Härtl, Roger

2017-08-01

Extreme lateral interbody fusion (ELIF) has gained popularity as a minimally invasive technique for indirect decompression. However, graft subsidence potentially threatens long-term success of ELIF. This study evaluated whether 26-mm-wide cages can eliminate subsidence and subsequent loss of decompression in ELIF. Patients undergoing ELIF surgery using a 26-mm-wide cage were analyzed retrospectively. Patient demographics and perioperative data for radiographic and clinical outcomes were recorded. Radiographic parameters included regional sagittal lumbar lordosis and foraminal and disc height. Clinical parameters were evaluated using the Oswestry Disability Index and visual analog scale. Subsidence of 26-mm-wide cages was compared with previous outcomes of patients undergoing ELIF using 18-mm-wide and 22-mm-wide cages. There were 21 patients and 28 spinal segments analyzed. Radiographic outcome measures such as disc and foraminal height revealed significant improvement at follow-up compared with before surgery (P = 0.001). Postoperative to last follow-up cage subsidence translated into 0.34 mm ± 0.26 and -0.55 mm ± 0.64 in disc and foraminal height loss, respectively. Patients with 26-mm-wide cages experienced less subsidence by means of disc (26 mm vs. 18 mm and 22 mm, P ≤ 0.05) and foraminal height (26 mm vs. 18 mm, P = 0.005; 26 mm vs. 22 mm, P = 0.208) loss compared with patients receiving 18-mm-wide and 22-mm-wide cages. The 26-mm-wide cages almost eliminated cage subsidence in ELIF. Compared with 18-mm-wide and 22-mm-wide cages, 26-mm-wide cages significantly reduced cage subsidence in ELIF at midterm follow-up. A 26-mm-wide cage should be used in ELIF to achieve sustained indirect decompression. Copyright © 2017. Published by Elsevier Inc.

Do Lordotic Cages Provide Better Segmental Lordosis Versus Nonlordotic Cages in Lateral Lumbar Interbody Fusion (LLIF)?

PubMed

Sembrano, Jonathan N; Horazdovsky, Ryan D; Sharma, Amit K; Yson, Sharon C; Santos, Edward R G; Polly, David W

2017-05-01

A retrospective comparative radiographic review. To evaluate the radiographic changes brought about by lordotic and nonlordotic cages on segmental and regional lumbar sagittal alignment and disk height in lateral lumbar interbody fusion (LLIF). The effects of cage design on operative level segmental lordosis in posterior interbody fusion procedures have been reported. However, there are no studies comparing the effect of sagittal implant geometry in LLIF. This is a comparative radiographic analysis of consecutive LLIF procedures performed with use of lordotic and nonlordotic interbody cages. Forty patients (61 levels) underwent LLIF. Average age was 57 years (range, 30-83 y). Ten-degree lordotic PEEK cages were used at 31 lumbar interbody levels, and nonlordotic cages were used at 30 levels. The following parameters were measured on preoperative and postoperative radiographs: segmental lordosis; anterior and posterior disk heights at operative level; segmental lordosis at supra-level and subjacent level; and overall lumbar (L1-S1) lordosis. Measurement changes for each cage group were compared using paired t test analysis. The use of lordotic cages in LLIF resulted in a significant increase in lordosis at operative levels (2.8 degrees; P=0.01), whereas nonlordotic cages did not (0.6 degrees; P=0.71) when compared with preoperative segmental lordosis. Anterior and posterior disk heights were significantly increased in both groups (P<0.01). Neither cage group showed significant change in overall lumbar lordosis (lordotic P=0.86 vs. nonlordotic P=0.25). Lordotic cages provided significant increase in operative level segmental lordosis compared with nonlordotic cages although overall lumbar lordosis remained unchanged. Anterior and posterior disk heights were significantly increased by both cages, providing basis for indirect spinal decompression.

Development of furnished cages for laying hens.

PubMed

Appleby, M C; Walker, A W; Nicol, C J; Lindberg, A C; Freire, R; Hughes, B O; Elson, H A

2002-09-01

1. A 3-year trial was carried out of cages for laying hens, occupying a full laying house. The main cage designs used were 5000 cm2 in area, 50 cm high at the rear and furnished with nests and perches. F cages had a front rollaway nest at the side, lined with artificial turf. FD cages also had a dust bath containing sand over the nest. H cages had two nest hollows at the side, one in front of the other. They were compared with conventional cages 2500 cm2 in area and 38 cm high at the rear. 2. Cages were stocked with from 4 to 8 ISA Brown hens per cage, resulting in varied allowances of area, feeder and perch per bird. No birds were beak trimmed. In F and FD cages two further treatments were applied: nests and dust baths were sometimes fitted with gates to exclude birds from dust baths in the morning and from both at night; elevated food troughs, with a lip 33 cm above the cage floor, were compared with standard troughs. 3. Management of the house was generally highly successful, with temperature control achieved by ventilation. Egg production was above breeders' standards and not significantly affected by cage design. More eggs per bird were collected when there were fewer birds per cage but food consumption also then tended to be higher. 4. The number of downgraded eggs was variable, with some tendency for more in furnished cages. Eggs laid in dust baths were often downgraded. Those laid at the back of the cage were frequently dirty because of accumulation of droppings. H nests were unsuccessful, with less than 50% of eggs laid in the nest hollows. However, up to 93% of eggs were laid in front rollaways, and few of these were downgraded. 5. Feather and foot damage were generally less in furnished than in conventional cages, greater where there were more birds per cage. With an elevated food trough there was less feather damage but more overgrowth of claws. In year 2, mortality was greater in cages with more birds. 6. Pre-laying behaviour was mostly settled in front rollaway nests. Dust baths were used more for pecking and scratching than for dust bathing. Comfort behaviour was more frequent in furnished cages than conventional, although still not frequent. Locomotion was strongly affected by number of birds per cage or by space per bird, being reduced by crowding. Most birds perched at night except in one treatment providing only 10.7 cm perch per bird. 7. Behaviour was more unrestricted and varied, and physical condition was better, in furnished than in conventional cages. However, egg production will cost more in furnished cages, partly because more eggs are downgraded. Dust baths must be fitted with gates that the birds cannot open from outside, but gates for nest boxes were found unnecessary. If a low perch is fitted it must be far enough from the back of the cage for birds to walk there. 8. Where there was less space per bird (more birds per cage) than the requirements in the 1999 European Commission Directive on laying hens, there were: fewer eggs per hen, but still above the breeders' target; lower food consumption; more feather and foot damage, but less than in conventional cages; higher mortality in one trial out of three; less freedom of movement. However, the results were still very good even with 8 birds per cage, and support the principle that furnished cages provide an acceptable way of protecting the welfare of laying hens.

Rearing Laying Hens in Aviaries Reduces Fearfulness following Transfer to Furnished Cages

PubMed Central

Brantsæter, Margrethe; Tahamtani, Fernanda M.; Moe, Randi O.; Hansen, Tone B.; Orritt, Rachel; Nicol, Christine; Janczak, Andrew M.

2016-01-01

Appropriate rearing is essential for ensuring the welfare and productivity of laying hens. Early experience has the potential to affect the development of fearfulness. This study tested whether rearing in aviaries, as opposed to cages, reduces the fearfulness of laying hens after transfer to furnished cages. Fear responses were recorded as avoidance of a novel object in the home cage. Lohmann Selected Leghorns were reared in an aviary system or conventional rearing cages and then transported to furnished cages at 16 weeks, before the onset of lay. Observations of a selection of birds were conducted at 19 (N = 50 independent cages) and 21 (N = 48 independent cages) weeks of age. At 19 and 21 weeks, cage-reared birds showed higher levels of fearfulness indicated by spending more time away from the novel object compared to aviary-reared birds. These results suggest that rearing in an enriched aviary environment reduces fearfulness up to the fifth week after transfer to a new housing system, compared to rearing in cages. PMID:26955634

Acclimatization of mice to different cage types and social groupings with respect to fecal secretion of IgA and corticosterone metabolites.

PubMed

Bundgaard, Cathrine Juel; Kalliokoski, Otto; Abelson, Klas S P; Hau, Jann

2012-01-01

Stress associated with transport and change of environment may have widespread effects on physiological parameters in laboratory animals. To investigate the time needed for mice to acclimatize to a new environment, based on fecal IgA and corticosterone excretion, eightweek-old BALB/c mice of both genders were housed either in groups of eight in different cage types in open conventional cages, in Individual Ventilated Cages (IVC), in open conventional cages inside a plastic isolator, or in different group sizes (8, 4, 8, 10 or 12 mice in each group) in open conventional cages. Feces were collected from each cage on routine cage changing. There was no significant difference in corticosterone excretion in feces between animals housed in the different cage types or between animals housed in different group sizes. IgA excretion for both males and females was found to be affected by transfer of mice into a novel cage, and it was found that it takes at least four weeks for the mice to acclimatize to a new environment with respect to this parameter.

Investigation of compressible vortex flow characteristics

NASA Technical Reports Server (NTRS)

Muirhead, V. U.

1977-01-01

The nature of intense air vortices was studied and the factors which determine the intensity and rate of decay of both single and pairs of vortices were investigated. Vortex parameters of axial pressure differential, circulation, outflow rates, separation distance and directions of rotation were varied. Unconfined vortices, generated by a single rotating cage, were intensified by an increasing axial pressure gradient. Breakdown occurred when the axial gradient became negligible. The core radius was a function of the axial gradient. Dual vortices, generated by two counterrotating cages, rotated opposite to the attached cages. With minimum spacing only one vortex was formed which rotated in a direction opposite to the attached cage. When one cage rotated at half the speed of the other cage, one vortex formed at the higher speed cage rotating in the cage direction.

Animal Welfare and Food Safety Aspects of Confining Broiler Chickens to Cages

PubMed Central

Shields, Sara; Greger, Michael

2013-01-01

Simple Summary In commercial chicken meat production, broiler chickens are usually kept on the floor in ware-house like buildings, but the use of cages is becoming more common. Confining chickens to cages is a welfare problem, as has been thoroughly demonstrated for laying hens used for egg production. Caged broiler chickens may suffer from poor bone strength due to lack of exercise, feather loss, and restriction of natural behavior. There are also potential food safety concerns associated with the use of cages. While cages may provide an economic advantage in some geographical regions of the world, the severe, inherent disadvantages should also be considered before cages are more widely adopted in the global broiler chicken industry. Abstract In most areas of the world, broiler chickens are raised in floor systems, but cage confinement is becoming more common. The welfare of broiler chickens in cages is affected by movement restriction, poor bone strength due to lack of exercise, and prevention of key behavioral patterns such as dustbathing and ground scratching. Cages for broiler chickens also have a long history of causing skin and leg conditions that could further compromise welfare, but a lack of controlled studies makes it difficult to draw conclusions about newer cage designs. Cage environments are usually stocked at a higher density than open floor systems, and the limited studies available suggest that caging may lead to increased levels of fear and stress in the birds. Further, birds reared on the floor appear less likely to harbor and shed Salmonella, as litter may serve as a seeding agent for competitive exclusion by other microorganisms. Cages for laying hens used in egg production have met with substantial opposition due to welfare concerns and caging broiler chickens will likely be subject to the same kinds of social disapproval. PMID:26487409

Ammonia Levels and Urine-Spot Characteristics as Cage-Change Indicators for High-Density Individually Ventilated Mouse Cages

PubMed Central

Washington, Ida M; Payton, Mark E

2016-01-01

Mouse cage and bedding changes are potentially stressful to mice and are also labor- and resource-intensive. These changes are often performed on a calendar-based schedule to maintain a clean microenvironment and limit the concentrations of ammonia to which mice and workers are exposed. The current study sought to establish a performance-based approach to mouse cage-changing that uses urine spot characteristics as visual indicators of intracage ammonia levels. Colorimetric ammonia indicators were used to measure ammonia levels in individually-ventilated cages (IVC) housing male or female mice (n =5 per cage) of various strains at 1 to 16 d after cage change. Urine spot characteristics were correlated with ammonia levels to create a visual indicator of the cage-change criterion of 25 ppm ammonia. Results demonstrated a consistent increase in ammonia levels with days since cage change, with cages reaching the cage-change criterion at approximately 10 d for IVC containing male mice and 16 d for those with female mice. Ammonia levels were higher for male than female mice but were not correlated with mouse age. However, urine spot diameter, color, and edge characteristics were strongly correlated with ammonia levels. Husbandry practices based on using urine spot characteristics as indicators of ammonia levels led to fewer weekly cage changes and concomitant savings in labor and resources. Therefore, urine spot characteristics can be used as visual indicators of intracage ammonia levels for use of a performance (urine spot)-based approach to cage-changing frequency that maintains animal health and wellbeing. PMID:27177558

Compositions containing borane or carborane cage compounds and related applications

DOEpatents

Bowen, III, Daniel E; Eastwood, Eric A

2013-05-28

Compositions comprising a polymer-containing matrix and a filler comprising a cage compound selected from borane cage compounds, carborane cage compounds, metal complexes thereof, residues thereof, mixtures thereof, and/or agglomerations thereof, where the cage compound is not covalently bound to the matrix polymer. Methods of making and applications for using such compositions are also disclosed.

Compositions containing borane or carborane cage compounds and related applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowen, III, Daniel E; Eastwood, Eric A

2014-11-11

Compositions comprising a polymer-containing matrix and a filler comprising a cage compound selected from borane cage compounds, carborane cage compounds, metal complexes thereof, residues thereof, mixtures thereof, and/or agglomerations thereof, where the cage compound is not covalently bound to the matrix polymer. Methods of making and applications for using such compositions are also disclosed.

Compositions containing borane or carborane cage compounds and related applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowen, III, Daniel E.; Eastwood, Eric A.

2015-09-15

Compositions comprising a polymer-containing matrix and a filler comprising a cage compound selected from borane cage compounds, carborane cage compounds, metal complexes thereof, residues thereof, mixtures thereof, and/or agglomerations thereof, where the cage compound is not covalently bound to the matrix polymer. Methods of making and applications for using such compositions are also disclosed.

Cage Change Influences Serum Corticosterone and Anxiety-Like Behaviors in the Mouse

PubMed Central

Rasmussen, Skye; Miller, Melinda M.; Filipski, Sarah B.; Tolwani, Ravi J.

2011-01-01

Environmental variables and husbandry practices can influence physiology and alter behavior in mice. Our study evaluated the effects of cage change on serum corticosterone levels and anxiety-like behaviors in C57BL/6 male mice. We examined the effects of 3 different methods of performing cage transfer and of transferring mice to a clean or a dirty familiar cage microenvironment. The 3 different handling methods were forceps transfer, gentle transfer with gloved hands, and a passive transfer technique that did not involve active handling. Active handling methods and transfer to both clean and dirty cage microenvironments significantly increased serum corticosterone 15 min after cage change; however, at 60 min after cage change, levels were comparable to those of unmanipulated mice. Although the effects were transient, cage change altered anxiety-like behaviors in the open field when behavioral testing was performed on the same day. These results demonstrate that the timing of cage change can influence behavioral results, an effect that is an important consideration for rodent behavioral studies. PMID:21838975

Development of an integrated CAD-FEA system for patient-specific design of spinal cages.

PubMed

Zhang, Mingzheng; Pu, Fang; Xu, Liqiang; Zhang, Linlin; Liang, Hang; Li, Deyu; Wang, Yu; Fan, Yubo

2017-03-01

Spinal cages are used to create a suitable mechanical environment for interbody fusion in cases of degenerative spinal instability. Due to individual variations in bone structures and pathological conditions, patient-specific cages can provide optimal biomechanical conditions for fusion, strengthening patient recovery. Finite element analysis (FEA) is a valuable tool in the biomechanical evaluation of patient-specific cage designs, but the time- and labor-intensive process of modeling limits its clinical application. In an effort to facilitate the design and analysis of patient-specific spinal cages, an integrated CAD-FEA system (CASCaDeS, comprehensive analytical spinal cage design system) was developed. This system produces a biomechanical-based patient-specific design of spinal cages and is capable of rapid implementation of finite element modeling. By comparison with commercial software, this system was validated and proven to be both accurate and efficient. CASCaDeS can be used to design patient-specific cages with a superior biomechanical performance to commercial spinal cages.

Energetic constraints, not predation, influence the evolution of sleep patterning in mammals.

PubMed

Capellini, I; Nunn, C L; McNamara, P; Preston, B T; Barton, R A

2008-10-01

Mammalian sleep is composed of two distinct states - rapid-eye-movement (REM) and non-REM (NREM) sleep - that alternate in cycles over a sleep bout. The duration of these cycles varies extensively across mammalian species. Because the end of a sleep cycle is often followed by brief arousals to waking, a shorter sleep cycle has been proposed to function as an anti-predator strategy. Similarly, higher predation risk could explain why many species exhibit a polyphasic sleep pattern (division of sleep into several bouts per day), as having multiple sleep bouts avoids long periods of unconsciousness, potentially reducing vulnerability.Using phylogenetic comparative methods, we tested these predictions in mammals, and also investigated the relationships among sleep phasing, sleep-cycle length, sleep durations and body mass.Neither sleep-cycle length nor phasing of sleep was significantly associated with three different measures of predation risk, undermining the idea that they represent anti-predator adaptations.Polyphasic sleep was associated with small body size, shorter sleep cycles and longer sleep durations. The correlation with size may reflect energetic constraints: small animals need to feed more frequently, preventing them from consolidating sleep into a single bout. The reduced daily sleep quotas in monophasic species suggests that the consolidation of sleep into one bout per day may deliver the benefits of sleep more efficiently and, since early mammals were small-bodied and polyphasic, a more efficient monophasic sleep pattern could be a hitherto unrecognized advantage of larger size.

Computed Tomography Measurement of Rib Cage Morphometry in Emphysema

PubMed Central

Sverzellati, Nicola; Colombi, Davide; Randi, Giorgia; Pavarani, Antonio; Silva, Mario; Walsh, Simon L.; Pistolesi, Massimo; Alfieri, Veronica; Chetta, Alfredo; Vaccarezza, Mauro; Vitale, Marco; Pastorino, Ugo

2013-01-01

Background Factors determining the shape of the human rib cage are not completely understood. We aimed to quantify the contribution of anthropometric and COPD-related changes to rib cage variability in adult cigarette smokers. Methods Rib cage diameters and areas (calculated from the inner surface of the rib cage) in 816 smokers with or without COPD, were evaluated at three anatomical levels using computed tomography (CT). CTs were analyzed with software, which allows quantification of total emphysema (emphysema%). The relationship between rib cage measurements and anthropometric factors, lung function indices, and %emphysema were tested using linear regression models. Results A model that included gender, age, BMI, emphysema%, forced expiratory volume in one second (FEV1)%, and forced vital capacity (FVC)% fit best with the rib cage measurements (R2 = 64% for the rib cage area variation at the lower anatomical level). Gender had the biggest impact on rib cage diameter and area (105.3 cm2; 95% CI: 111.7 to 98.8 for male lower area). Emphysema% was responsible for an increase in size of upper and middle CT areas (up to 5.4 cm2; 95% CI: 3.0 to 7.8 for an emphysema increase of 5%). Lower rib cage areas decreased as FVC% decreased (5.1 cm2; 95% CI: 2.5 to 7.6 for 10 percentage points of FVC variation). Conclusions This study demonstrates that simple CT measurements can predict rib cage morphometric variability and also highlight relationships between rib cage morphometry and emphysema. PMID:23935872

Dynamic characteristic of electromechanical coupling effects in motor-gear system

NASA Astrophysics Data System (ADS)

Bai, Wenyu; Qin, Datong; Wang, Yawen; Lim, Teik C.

2018-06-01

Dynamic characteristics of an electromechanical model which combines a nonlinear permeance network model (PNM) of a squirrel-cage induction motor and a coupled lateral-torsional dynamic model of a planetary geared rotor system is analyzed in this study. The simulations reveal the effects of internal excitations or parameters like machine slotting, magnetic saturation, time-varying mesh stiffness and shaft stiffness on the system dynamics. The responses of the electromechanical system with PNM motor model are compared with those responses of the system with dynamic motor model. The electromechanical coupling due to the interactions between the motor and gear system are studied. Furthermore, the frequency analysis of the electromechanical system dynamic characteristics predicts an efficient way to detect work condition of unsymmetrical voltage sag.

Induction of prolonged natural lifespans in mice exposed to acoustic environmental enrichment.

PubMed

Yamashita, Yuichi; Kawai, Norie; Ueno, Osamu; Matsumoto, Yui; Oohashi, Tsutomu; Honda, Manabu

2018-05-21

We investigated the effect of acoustic environmental enrichment (EE) on the lifespans and behaviours of mice to the end of their natural lifespan in different acoustic environments. Acoustic EE induced a significantly prolonged natural lifespan (nearly 17% longer) and was associated with increased voluntary movements. However, no correlation between lifespan and voluntary movements was detected, suggesting that increased voluntary movements are not a primary cause of lifespan prolongation. Analyses of individual differences in lifespan demonstrated that lifespan extension induced by acoustic EE could be related to changes in social relationships (e.g., reduction of social conflict) among individuals kept within a cage. Therefore, an acoustic component may be an important factor inducing the positive effects of EE.

Influence of Tribology of Cage Material on Ball Bearing Cage Instability

NASA Astrophysics Data System (ADS)

Servais, S.; Duquenne, M.; Bozet, J.-L.

2013-09-01

By creating a solid lubricant thickness on both bearing races, a cage material of cryogenic ball bearing plays a significant role in the good dynamical behavior of the cage. This role is essential because of the lack of conventional lubricant into this kind of bearing.In this paper, a method able to identify if a particular potential cage material can correctly fulfill its function is described. In other words, if it can lead to a stable movement of the cage. From the identification of fundamental tribological parameters governing the cage behavior, this method presents an example of ranking of such materials. This is based on pin-on-disk tests and on a numerical approach.

25 CFR 542.14 - What are the minimum internal control standards for the cage?

Code of Federal Regulations, 2010 CFR

2010-04-01

... the cage shall be recorded on a cage accountability form on a per-shift basis. (6) Only cash, cash... identity, including photo identification. (8) A file for customers shall be prepared prior to acceptance of... cage shall be summarized on a cage accountability form on a per shift basis and shall be supported by...

Atypical gnawing and cage destructive behavior in one strain of laboratory rat.

PubMed

Jacobs, H K; Van Pelt, L F; Dunlap, B K

1984-06-01

Approximately 80% of a colony of 900 Long Evans rats, Blu:(LE), gnawed on polypropylene shoe box type cages around the automatic watering grommet. The gnawing led to cage destruction and escape of the animals. The addition of a large stainless steel shield between the original grommet backing and the cage prevented further gnawing on the cage.

Effects of a 28-Day Cage-Change Interval on Intracage Ammonia Levels, Nasal Histology, and Perceived Welfare of CD1 Mice

PubMed Central

Vogelweid, Catherine M; Zapien, Kathleen A; Honigford, Matthew J; Li, Linghui; Li, Hua; Marshall, Heather

2011-01-01

We measured daily intracage ammonia levels and performed weekly assessments of CD1 male, female, and breeder mice housed within disposable, ventilated cages that remained unchanged for 28 d. We tested housing groups comprising 1, 3, or 5 sex-matched mice per cage and breeder pairs with litters. Mice housed in cages with higher concentrations of ammonia developed degeneration and inflammatory lesions in the nasal passages. Mean ammonia exposure levels that caused rhinitis were 181 ppm for 18 d. Ammonia exposures of 93 ppm for 16 d caused necrosis of the olfactory epithelium, whereas 52 ppm for 13 d caused epithelial degeneration. Observers could not detect visible signs of rhinitis or identify cages with elevated ammonia levels, nor did they identify any sick or distressed mice. Observers consistently assigned poorer welfare scores as cages became dirtier. We conclude that we can extend the cage-change interval to at least 28 d for disposable, ventilated caging housing a single CD1 mouse. Cages containing 3 CD1 mice of either sex should be changed biweekly, and cages containing 5 CD1 mice or breeder pairs should be changed at least once weekly. PMID:22330779

Dynamical cage behaviour and hydrogen migration in hydrogen and hydrogen-tetrahydrofuran clathrate hydrates

NASA Astrophysics Data System (ADS)

Gorman, Paul D.; English, Niall J.; MacElroy, J. M. D.

2012-01-01

Classical equilibrium molecular dynamics simulations have been performed to investigate dynamical properties of cage radial breathing modes and intra- and inter-cage hydrogen migration in both pure hydrogen and mixed hydrogen-tetrahydrofuran sII hydrates at 0.05 kbar and up to 250 K. For the mixed H2-THF system in which there is single H2 occupation of the small cage (labelled "1SC 1LC"), we find that no H2 migration occurs, and this is also the case for pure H2 hydrate with single small-cavity occupation and quadruple occupancy for large cages (dubbed "1SC 4LC"). However, for the more densely filled H2-THF and pure-H2 systems, in which there is double H2 occupation in the small cage (dubbed "2SC 1LC" and "2SC 4LC," respectively), there is an onset of inter-cage H2 migration events from the small cages to neighbouring cavities at around 200 K, with an approximate Arrhenius temperature-dependence for the migration rate from 200 to 250 K. It was found that these "cage hopping" events are facilitated by temporary openings of pentagonal small-cage faces with the relaxation and reformation of key stabilising hydrogen bonds during and following passage. The cages remain essentially intact up to 250 K, save for transient hydrogen bond weakening and reformation during and after inter-cage hydrogen diffusion events in the 200-250 K range. The "breathing modes," or underlying frequencies governing the variation in the cavities' radii, exhibit a certain overlap with THF rattling motion in the case of large cavities, while there is some overlap of small cages' radial breathing modes with lattice acoustic modes.

Architecture of clathrin fullerene cages reflects a geometric constraint--the head-to-tail exclusion rule--and a preference for asymmetry.

PubMed

Schein, Stan

2009-03-27

Fullerene cages have n trivalent vertices, 12 pentagonal faces, and (n-20)/2 hexagonal faces. The smallest cage in which all of the pentagons are surrounded by hexagons and thus isolated from each other has 60 vertices and is shaped like a soccer ball. The protein clathrin self-assembles into fullerene cages of a variety of sizes and shapes, including smaller ones with adjacent pentagons as well as larger ones, but the variety is limited. To explain the range of clathrin architecture and how these fullerene cages self-assemble, we proposed a hypothesis, the "head-to-tail exclusion rule" (the "Rule"). Of the 5769 small clathrin cage isomers with n< or =60 vertices and adjacent pentagons, the Rule permits just 15, three identified in 1976 and 12 others. A "weak version" of the Rule permits another 99. Based on cryo-electron tomography, Cheng et al. reported six raw clathrin fullerene cages. One was among the three identified in 1976. Here, (1) we identify the remaining five. (2) Four are new and are among the 12 others permitted by the Rule. (3) One, also new, is among the 99 weak version cages. (4) Of particular note, none of the remaining 5565 excluded cages has been identified. These findings provide powerful experimental confirmation of the Rule and the principle on which it is based. (5) Surprisingly, the newly identified clathrin cages are among the least symmetric of those permitted. (6) By devising a method for counting assembly paths, (7) we show that asymmetric cages can be assembled by larger numbers of paths, thus providing a kinetic explanation for the prevalence of asymmetric cages. (8) Finally, we show that operation during cage growth of the Rule greatly increases the likelihood of producing a closed fullerene cage, specifically one of those permitted, but efficient assembly still appears to require internal remodeling.

The influence of fish cage aquaculture on pelagic carbon flow and water chemistry in tidally dominated mangrove estuaries of peninsular Malaysia.

PubMed

Alongi, D M; Chong, V C; Dixon, P; Sasekumar, A; Tirendi, F

2003-05-01

The impact of floating net cages culturing the seabass, Lates calcarifer, on planktonic processes and water chemistry in two heavily used mangrove estuaries in Malaysia was examined. Concentrations of dissolved inorganic and particulate nutrients were usually greater in cage vs. adjacent (approximately 100 m) non-cage waters, although most variability in water-column chemistry related to water depth and tides. There were few consistent differences in plankton abundance, production or respiration between cage and non-cage sites. Rates of primary production were low compared with rates of pelagic mineralization reflecting high suspended loads coupled with large inputs of organic matter from mangrove forests, fishing villages, fish cages, pig farms and other industries within the catchment. Our preliminary sampling did not reveal any large-scale eutrophication due to the cages. A crude estimate of the contribution of fish cage inputs to the estuaries shows that fish cages contribute only approximately 2% of C but greater percentages of N (32-36%) and P (83-99%) to these waters relative to phytoplankton and mangrove inputs. Isolating and detecting impacts of cage culture in such heavily used waterways--a situation typical of most mangrove estuaries in Southeast Asia--are constrained by a background of large, highly variable fluxes of organic material derived from extensive mangrove forests and other human activities. Copyright 2002 Elsevier Science B.V.

Solute diffusion through fibrotic tissue formed around protective cage system for implantable devices.

PubMed

Prihandana, Gunawan Setia; Ito, Hikaru; Tanimura, Kohei; Yagi, Hiroshi; Hori, Yuki; Soykan, Orhan; Sudo, Ryo; Miki, Norihisa

2015-08-01

This article presents the concept of an implantable cage system that can house and protect implanted biomedical sensing and therapeutic devices in the body. Cylinder-shaped cages made of porous polyvinyl alcohol (PVA) sheets with an 80-µm pore size and/or stainless steel meshes with 0.54-mm openings were implanted subcutaneously in the dorsal region of rats for 5 weeks. Analysis of the explanted cages showed the formation of fibrosis tissue around the cages. PVA cages had fibrotic tissue growing mostly along the outer surface of cages, while stainless steel cages had fibrotic tissue growing into the inside surface of the cage structure, due to the larger porosity of the stainless steel meshes. As the detection of target molecules with short time lags for biosensors and mass transport with low diffusion resistance into and out of certain therapeutic devices are critical for the success of such devices, we examined whether the fibrous tissue formed around the cages were permeable to molecules of our interest. For that purpose, bath diffusion and microfluidic chamber diffusion experiments using solutions containing the target molecules were performed. Diffusion of sodium, potassium and urea through the fibrosis tissue was confirmed, thus suggesting the potential of these cylindrical cages surrounded by fibrosis tissue to successfully encase implantable sensors and therapeutic apparatus. © 2014 Wiley Periodicals, Inc.

Performance and welfare of rabbit does in various caging systems.

PubMed

Mikó, A; Matics, Zs; Gerencsér, Zs; Odermatt, M; Radnai, I; Nagy, I; Szendrő, K; Szendrő, Zs

2014-07-01

The objective of the study was to compare production and welfare of rabbit does and their kits housed in various types of cages. Female rabbits were randomly allocated to four groups with the following cage types: CN: common wire-mesh flat-deck cage, without footrest; CF: cage similar to the CN but with plastic footrest; ECWP: enlarged cage with wire-mesh platform; and ECPP: extra enlarged cage with plastic-mesh platform. All does were inseminated on the same day, 11 days after kindlings. Reproductive performance was evaluated during the first five consecutive kindlings. Severity of sore hocks was scored at each insemination. Location preference of the does and the platform usage of their kits were evaluated. Kindling rate, litter size (total born, born alive, alive at 21 and 35 days) and kit mortality were not significantly influenced by the cage types. The litter weight at 21 days was higher in ECWP and ECPP cages than in the CF group (3516, 3576 and 3291 g, respectively; P2.5 cm) and 3 to 4 (3=callus opened, cracks present; 4=wounds) were 58%, 60%, 78% and 48%, and 0%, 5%, 0% and 48% in groups ECPP, ECWP, CF and CN, respectively. Higher number of daily nest visits was observed for CF does than for ECWP does (12.5 v. 5.9; P2/day) was higher in the CF group than in the ECWP group (12.1 v. 3.2%; P<0.01). Within large cages, the does were observed on the platform more frequently in the ECPP cages compared with the ECWP cages (56.9% v. 31.7%; P<0.001). Similarly, 2.7% and 0.2% of kits at 21 days of age, and 33.2% and 5.2% of kits at 28 days of age, were found on the platforms of ECPP and ECWP cages, respectively. In conclusion, cages larger than the conventional ones improved kits' weaning weight, plastic footrests and plastic-mesh platforms in conventional and/or large cages reduced sore hocks' problems, plastic-mesh platforms were more used by both does and kits compared with the wire-mesh platforms.

Stand-alone lumbar cage subsidence: A biomechanical sensitivity study of cage design and placement.

PubMed

Calvo-Echenique, Andrea; Cegoñino, José; Chueca, Raúl; Pérez-Del Palomar, Amaya

2018-08-01

Spinal degeneration and instability are commonly treated with interbody fusion cages either alone or supplemented with posterior instrumentation with the aim to immobilise the segment and restore intervertebral height. The purpose of this work is to establish a tool which may help to understand the effects of intervertebral cage design and placement on the biomechanical response of a patient-specific model to help reducing post-surgical complications such as subsidence and segment instability. A 3D lumbar functional spinal unit (FSU) finite element model was created and a parametric model of an interbody cage was designed and introduced in the FSU. A Drucker-Prager Cap plasticity formulation was used to predict plastic strains and bone failure in the vertebrae. The effect of varying cage size, cross-sectional area, apparent stiffness and positioning was evaluated under 500 N preload followed by 7.5 Nm multidirectional rotation and the results were compared with the intact model. The most influential cage parameters on the FSU were size, curvature congruence with the endplates and cage placement. Segmental stiffness was higher when increasing the cross-sectional cage area in all loading directions and when the cage was anteriorly placed in all directions but extension. In general, the facet joint forces were reduced by increasing segmental stiffness. However, these forces were higher than in the intact model in most of the cases due to the displacement of the instantaneous centre of rotation. The highest plastic deformations took place at the caudal vertebra under flexion and increased for cages with greater stiffness. Thus, wider cages and a more anteriorly placement would increase the volume of failed bone and, therefore, the risk of subsidence. Cage geometry plays a crucial role in the success of lumbar surgery. General considerations such as larger cages may be applied as a guideline, but parameters such as curvature or cage placement should be determined for each specific patient. This model provides a proof-of-concept of a tool for the preoperative evaluation of lumbar surgical outcomes. Copyright © 2018 Elsevier B.V. All rights reserved.

The effect of cage and house design on egg production and egg weight of White Leghorn hens: an epidemiological study.

PubMed

Garner, J P; Kiess, A S; Mench, J A; Newberry, R C; Hester, P Y

2012-07-01

Hen performance can be affected by many interacting variables related to cage design, such as floor area, height, tier arrangement, and feeder and drinker type and placement within the cage. Likewise, features of house design such as waste management and lighting can also affect hen productivity. The influence of these design aspects on hen performance has not been fully assessed. Determining the effects of numerous, interacting variables is impractical in a traditional experiment; therefore, an epidemiological approach, using variability in cage and house design among and within commercial producers, was employed to identify features that affect egg production and egg weight. A universal cage measurement system was created to calculate cage design variables. A database for recording information on cage design, resource location, waste management, environmental conditions, and hen productivity was developed. Production outcomes were assessed from placement to 60 wk of age in White Leghorns (n = 165-168 houses). Using GLM, a statistical model was identified that best described the variance in egg traits. Eggs/hen-housed increased with greater feeder space allocation (P = 0.031); taller cages (P = 0.029); rear (vs. front) drinker location in vertical cages (P = 0.026); and regular removal of manure from the house (P = 0.005). Case weight of eggs was greater in A-frame houses where manure was removed regularly instead of being left in the house (P < 0.001); with increasing cage floor slope (P = 0.001); in cages where drinkers were placed more toward the front or back of the cage as compared with the middle of the cage (P < 0.001); with more space/hen (P = 0.024); and with higher caloric intake (P < 0.001). Perhaps because of its negative correlation with egg production, case weight of eggs increased with less feeder space allocation (P = 0.004) and shorter cage heights (P < 0.001). These results reveal important effects of feeder space, floor space, cage height, drinker position, and waste management on hen productivity.

Experimental evidence supports the abscess theory of development of radicular cysts.

PubMed

Nair, P N R; Sundqvist, Göran; Sjögren, Ulf

2008-08-01

The objective of this study was to experimentally induce inflammatory cysts in an animal model so as to test the hypothesis that radicular cysts develop via the "abscess pathway." Twenty-eight perforated custom-made Teflon cages were surgically implanted into defined locations in the back of 7 Sprague Dawley rats. A week after the implantation of the cages, a known quantity of freshly grown, close allogeneic oral keratinocytes in phosphate buffer solution (PBS) was injected into each cage. One cage per animal was treated as the control that received only epithelial cells. The remaining 3 cages of each animal were trials. Seven days post epithelial cell inoculation; a suspension of 0.2 mL of Fusobacterium nucleatum (10(8) bacteria per mL) was injected into each of the 3 trial cages. Two, 12, and 24 weeks after the inoculation of the bacteria, the cages were taken out, and the tissue contents were fixed and processed by correlative light and transmission electron microscopy. Sixteen of the 21 trial cages could be processed and yielded results. Inoculations of epithelial cells followed 1 week later by F. nucleatum into tissue cages resulted in the development inflammatory cysts in 2 of the 16 cages. The 2 cages contained a total of 4 cystic sites. None of the control cages showed the presence of any cyst-like pathology. Inflammatory cysts were induced by initiating acute inflammatory foci (abscess/necrotic area) by bacterial injection that got enclosed by a proliferating epithelium. This finding provides strong experimental evidence in support of the "abscess theory" of development of radicular cysts.

Bisphenol A is released from used polycarbonate animal cages into water at room temperature

USGS Publications Warehouse

Howdeshell, Kembra L.; Peterman, Paul H.; Judy, Barbara M.; Taylor, Julia A.; Orazio, Carl E.; Ruhlen, Rachel L.; vom Saal, Frederick S.; Welshons, Wade V.

2003-01-01

Bisphenol A (BPA) is a monomer with estrogenic activity that is used in the production of food packaging, dental sealants, polycarbonate plastic, and many other products. The monomer has previously been reported to hydrolyze and leach from these products under high heat and alkaline conditions, and the amount of leaching increases as a function of use. We examined whether new and used polycarbonate animal cages passively release bioactive levels of BPA into water at room temperature and neutral pH. Purified water was incubated at room temperature in new polycarbonate and polysulfone cages and used (discolored) polycarbonate cages, as well as control (glass and used polypropylene) containers. The resulting water samples were characterized with gas chromatography/mass spectrometry (GC/MS) and tested for estrogenic activity using an MCF-7 human breast cancer cell proliferation assay. Significant estrogenic activity, identifiable as BPA by GC/MS (up to 310 micro g/L), was released from used polycarbonate animal cages. Detectable levels of BPA were released from new polycarbonate cages (up to 0.3 micro g/L) as well as new polysulfone cages (1.5 micro g/L), whereas no BPA was detected in water incubated in glass and used polypropylene cages. Finally, BPA exposure as a result of being housed in used polycarbonate cages produced a 16% increase in uterine weight in prepubertal female mice relative to females housed in used polypropylene cages, although the difference was not statistically significant. Our findings suggest that laboratory animals maintained in polycarbonate and polysulfone cages are exposed to BPA via leaching, with exposure reaching the highest levels in old cages.

Molecular marriage through partner preferences in covalent cage formation and cage-to-cage transformation.

PubMed

Acharyya, Koushik; Mukherjee, Sandip; Mukherjee, Partha Sarathi

2013-01-16

Unprecedented self-sorting of three-dimensional purely organic cages driven by dynamic covalent bonds is described. Four different cages were first synthesized by condensation of two triamines and two dialdehydes separately. When a mixture of all the components was allowed to react, only two cages were formed, which suggests a high-fidelity self-recognition. The issue of the preference of one triamine for a particular dialdehyde was further probed by transforming a non-preferred combination to either of the two preferred combinations by reacting it with the appropriate triamine or dialdehyde.

A stochastic frontier analysis of technical efficiency of fish cage culture in Peninsular Malaysia.

PubMed

Islam, Gazi Md Nurul; Tai, Shzee Yew; Kusairi, Mohd Noh

2016-01-01

Cage culture plays an important role in achieving higher output and generating more export earnings in Malaysia. However, the cost of fingerlings, feed and labour have increased substantially for cage culture in the coastal areas in Peninsular Malaysia. This paper uses farm level data gathered from Manjung, Perak and Kota Tinggi, Johor to investigate the technical efficiency of brackish water fish cage culture using the stochastic frontier approach. The technical efficiency was estimated and specifically the factors affecting technical inefficiencies of fish cage culture system in Malaysia was investigated. On average, 37 percent of the sampled fish cage farms are technically efficient. The results suggest very high degrees of technical inefficiency exist among the cage culturists. This implies that great potential exists to increase fish production through improved efficiency in cage culture management in Peninsular Malaysia. The results indicate that farmers obtained grouper fingerlings from other neighboring countries due to scarcity of fingerlings from wild sources. The cost of feeding for grouper (Epinephelus fuscoguttatus) requires relatively higher costs compared to seabass (Lates calcarifer) production in cage farms in the study areas. Initiatives to undertake extension programmes at the farm level are needed to help cage culturists in utilizing their resources more efficiently in order to substantially enhance their fish production.

A secure semi-field system for the study of Aedes aegypti.

PubMed

Ritchie, Scott A; Johnson, Petrina H; Freeman, Anthony J; Odell, Robin G; Graham, Neal; Dejong, Paul A; Standfield, Graeme W; Sale, Richard W; O'Neill, Scott L

2011-03-22

New contained semi-field cages are being developed and used to test novel vector control strategies of dengue and malaria vectors. We herein describe a new Quarantine Insectary Level-2 (QIC-2) laboratory and field cages (James Cook University Mosquito Research Facility Semi-Field System; MRF SFS) that are being used to measure the impact of the endosymbiont Wolbachia pipientis on populations of Aedes aegypti in Cairns Australia. The MRF consists of a single QIC-2 laboratory/insectary that connects through a central corridor to two identical QIC-2 semi-field cages. The semi-field cages are constructed of two layers of 0.25 mm stainless steel wire mesh to prevent escape of mosquitoes and ingress of other insects. The cages are covered by an aluminum security mesh to prevent penetration of the cages by branches and other missiles in the advent of a tropical cyclone. Parts of the cage are protected from UV light and rainfall by 90% shade cloth and a vinyl cover. A wooden structure simulating the understory of a Queenslander-style house is also situated at one end of each cage. The remainder of the internal aspect of the cage is covered with mulch and potted plants to emulate a typical yard. An air conditioning system comprised of two external ACs that feed cooled, moistened air into the cage units. The air is released from the central ceiling beam from a long cloth tube that disperses the airflow and also prevents mosquitoes from escaping the cage via the AC system. Sensors located inside and outside the cage monitor ambient temperature and relative humidity, with AC controlled to match ambient conditions. Data loggers set in the cages and outside found a <2 °C temperature difference. Additional security features include air curtains over exit doors, sticky traps to monitor for escaping mosquitoes between layers of the mesh, a lockable vestibule leading from the connecting corridor to the cage and from inside to outside of the insectary, and screened (0.25 mm mesh) drains within the insectary and the cage. A set of standard operating procedures (SOP) has been developed to ensure that security is maintained and for enhanced surveillance for escaping mosquitoes on the JCU campus where the MRF is located. A cohort of male and female Aedes aegypti mosquitoes were released in the cage and sampled every 3-4 days to determine daily survival within the cage; log linear regression from BG-sentinel trapping collections produced an estimated daily survival of 0.93 and 0.78 for females and males, respectively. The MRF SFS allows us to test novel control strategies within a secure, contained environment. The air-conditioning system maintains conditions within the MRF cages comparable to outside ambient conditions. This cage provides a realistic transitional platform between the laboratory and the field in which to test novel control measures on quarantine level insects.

A Secure Semi-Field System for the Study of Aedes aegypti

PubMed Central

Ritchie, Scott A.; Johnson, Petrina H.; Freeman, Anthony J.; Odell, Robin G.; Graham, Neal; DeJong, Paul A.; Standfield, Graeme W.; Sale, Richard W.; O'Neill, Scott L.

2011-01-01

Background New contained semi-field cages are being developed and used to test novel vector control strategies of dengue and malaria vectors. We herein describe a new Quarantine Insectary Level-2 (QIC-2) laboratory and field cages (James Cook University Mosquito Research Facility Semi-Field System; MRF SFS) that are being used to measure the impact of the endosymbiont Wolbachia pipientis on populations of Aedes aegypti in Cairns Australia. Methodology/Principal Findings The MRF consists of a single QIC-2 laboratory/insectary that connects through a central corridor to two identical QIC-2 semi-field cages. The semi-field cages are constructed of two layers of 0.25 mm stainless steel wire mesh to prevent escape of mosquitoes and ingress of other insects. The cages are covered by an aluminum security mesh to prevent penetration of the cages by branches and other missiles in the advent of a tropical cyclone. Parts of the cage are protected from UV light and rainfall by 90% shade cloth and a vinyl cover. A wooden structure simulating the understory of a Queenslander-style house is also situated at one end of each cage. The remainder of the internal aspect of the cage is covered with mulch and potted plants to emulate a typical yard. An air conditioning system comprised of two external ACs that feed cooled, moistened air into the cage units. The air is released from the central ceiling beam from a long cloth tube that disperses the airflow and also prevents mosquitoes from escaping the cage via the AC system. Sensors located inside and outside the cage monitor ambient temperature and relative humidity, with AC controlled to match ambient conditions. Data loggers set in the cages and outside found a <2°C temperature difference. Additional security features include air curtains over exit doors, sticky traps to monitor for escaping mosquitoes between layers of the mesh, a lockable vestibule leading from the connecting corridor to the cage and from inside to outside of the insectary, and screened (0.25 mm mesh) drains within the insectary and the cage. A set of standard operating procedures (SOP) has been developed to ensure that security is maintained and for enhanced surveillance for escaping mosquitoes on the JCU campus where the MRF is located. A cohort of male and female Aedes aegypti mosquitoes were released in the cage and sampled every 3–4 days to determine daily survival within the cage; log linear regression from BG-sentinel trapping collections produced an estimated daily survival of 0.93 and 0.78 for females and males, respectively. Conclusions/Significance The MRF SFS allows us to test novel control strategies within a secure, contained environment. The air-conditioning system maintains conditions within the MRF cages comparable to outside ambient conditions. This cage provides a realistic transitional platform between the laboratory and the field in which to test novel control measures on quarantine level insects. PMID:21445333

Interactions Between Housing Density and Ambient Temperature in the Cage Environment: Effects on Mouse Physiology and Behavior.

PubMed

Toth, Linda A; Trammell, Rita A; Ilsley-Woods, Megan

2015-11-01

To determine how housing density and ambient temperature interact to influence the physiology and behavior of mice, we systematically varied housing density (1 to 5 mice per cage) and ambient temperature (22, 26, or 30 °C) and measured effects on body weight, food intake, diurnal patterns of locomotor activity and core temperature, fecal corticosterone, and serum cytokine and adipokine panels. Temperatures inside cages housing 5 mice were 1 to 2 °C higher than the ambient temperature. As the housing density decreased, in-cage temperatures began to fall at a density of 2 or 3 mice per cage and did not differ from ambient temperature at 1 mouse per cage. Ambient temperature, but not housing density, significantly affected food intake. Although neither ambient temperature nor housing density affected core temperature or activity, hyperthermia and behavioral activation occurred during the 12-h period after cage change. Fecal concentrations of corticosterone metabolites and serum cytokines, chemokines, insulin, and leptin were not influenced by cage density and were only sporadically influenced by ambient temperature. Our data document that the number of mice housed per cage influences the intracage environmental conditions and that ambient temperature influences food intake even when temperatures are within or near recommended or thermoneutral ranges. We conclude that investigators should be cautious when changing the number of mice housed in a cage over the course of a study, because doing so significantly alters the cage environment to which remaining mice are exposed.

Interactions Between Housing Density and Ambient Temperature in the Cage Environment: Effects on Mouse Physiology and Behavior

PubMed Central

Toth, Linda A; Trammell, Rita A; Ilsley-Woods, Megan

2015-01-01

To determine how housing density and ambient temperature interact to influence the physiology and behavior of mice, we systematically varied housing density (1 to 5 mice per cage) and ambient temperature (22, 26, or 30 °C) and measured effects on body weight, food intake, diurnal patterns of locomotor activity and core temperature, fecal corticosterone, and serum cytokine and adipokine panels. Temperatures inside cages housing 5 mice were 1 to 2 °C higher than the ambient temperature. As the housing density decreased, in-cage temperatures began to fall at a density of 2 or 3 mice per cage and did not differ from ambient temperature at 1 mouse per cage. Ambient temperature, but not housing density, significantly affected food intake. Although neither ambient temperature nor housing density affected core temperature or activity, hyperthermia and behavioral activation occurred during the 12-h period after cage change. Fecal concentrations of corticosterone metabolites and serum cytokines, chemokines, insulin, and leptin were not influenced by cage density and were only sporadically influenced by ambient temperature. Our data document that the number of mice housed per cage influences the intracage environmental conditions and that ambient temperature influences food intake even when temperatures are within or near recommended or thermoneutral ranges. We conclude that investigators should be cautious when changing the number of mice housed in a cage over the course of a study, because doing so significantly alters the cage environment to which remaining mice are exposed. PMID:26632780

Effects of single caging and cage size on behavior and stress level of domestic neutered cats housed in an animal shelter.

PubMed

Uetake, Katsuji; Goto, Akihiro; Koyama, Rumi; Kikuchi, Rieko; Tanaka, Toshio

2013-03-01

Cats need a minimum amount of space even in animal shelters. In this study the effects of single caging and cage size on the behavior and stress level of domestic cats were investigated. Six neutered cats (2-15 years old) that had been housed in a group for at least 7 months were moved to three kinds of single cages (small, medium and large) by rotation on a Latin square design. They experienced each cage size for 6 days. Cats could use vertical dimensions when housed in a group room and the large cage. Behavioral observation was conducted for 3 h in the evening, and stress levels were assessed by urine cortisol-to-creatinine ratios. The amounts (estimated proportions) of time spent in locomotion and social/solitary play were lower even in large cages than in group housing (both P < 0.05). Conversely, the amount of time spent resting tended to increase when housed singly (P = 0.104). The urine cortisol-to-creatinine ratios of singly housed cats tended to be higher than that of group-housed cats (P = 0.086). The results indicate that cats become less active when they are housed singly in cages regardless of the cage size. Cats seem to feel no undue stress even in small cages if the stay is short. © 2012 The Authors. Animal Science Journal © 2012 Japanese Society of Animal Science.

Play Caging Benefits the Behavior of Singly Housed Laboratory Rhesus Macaques (Macaca mulatta)

PubMed Central

Griffis, Caroline M; Martin, Allison L; Perlman, Jaine E; Bloomsmith, Mollie A

2013-01-01

This study addresses a recommendation in The Guide for the Care and Use of Laboratory Animals to provide singly housed nonhuman primates with intermittent access to large, enriched (play) caging. Research on the potential benefits of this type of caging is limited. The present study examines the effects of play caging on behavior, activity, and enrichment use. Singly housed, adult male, rhesus macaques (n = 10) underwent a baseline phase in their home cages, a 2-wk treatment phase with housing in play cages, and a posttreatment phase after returning to their home cages. Each subject underwent focal behavioral observations (n = 10; duration 30 min each) during each study phase, for a total of 150 h of data collection. Results showed increases in locomotion and enrichment use and a trend toward decreased abnormal behavior while subjects were in the play cage, with the durations of these behaviors returning to baseline levels after treatment. Anxiety-related behaviors decreased between the treatment and posttreatment phases but not between baseline and treatment, suggesting that outside factors may have influenced the decline. During the treatment phase, subjects spent more time in the upper quadrants of the play caging and preferred a mirror and forage boards as forms of enrichment. The greatest behavioral improvement occurred during the first week in the play cage. This study provides evidence to support the benefits of play caging for singly housed rhesus macaques. PMID:24041207

Particulate matter in animal rooms housing mice in microisolation caging.

PubMed

Langham, Gregory L; Hoyt, Robert F; Johnson, Thomas E

2006-11-01

Reactions to allergens created by laboratory animals are among the most frequently encountered occupational illnesses associated with research animals. Personnel are exposed to these allergens through airborne particulate matter. Although the use of microisolation caging systems can reduce particulate matter concentrations in rooms housing mice, the operating parameters of ventilated caging systems vary extensively. We compared room air in mouse rooms containing 5 different types of caging: 1) individually ventilated caging under positive pressure with filtered intake air and exhaust air returned to the room (VCR+), 2) individually ventilated caging under negative pressure with exhaust air returned to the room (VCR-), 3) individually ventilated caging under positive pressure with exhaust air returned to the heating, ventilation, and air-conditioning (HVAC) system, 4) individually ventilated caging under negative pressure with exhaust air returned to the HVAC system, and 5) static microisolation cages. We found that rooms under VCR conditions had fewer large particles than did those under other conditions, but the numbers of 0.3 microm particles did not differ significantly among systems. Static, positive or negative pressure applied to caging units as well as route of air exhaust were found to have little influence on the total number of particles in the atmosphere. Therefore, considering the heat load, odor, and overall particulate concentration in the room, placing individually ventilated caging under negative pressure with exhaust air returned to the HVAC system appears to be the optimal overall choice when using microisolation housing for rodents.

The effect of pesticide residue on caged mosquito bioassays.

PubMed

Barber, J A S; Greer, Mike; Coughlin, Jamie

2006-09-01

Wind tunnel experiments showed that secondary pickup of insecticide residue by mosquitoes in cage bioassays had a significant effect on mortality. Cage bioassays using adult Ochlerotatus taeniorhynchus (Wiedemann) investigated the effect of exposure time to a contaminated surface. Cages were dosed in a wind tunnel using the LC50 for naled (0.124 mg a.i./ml) and an LC25 (0.0772 mg a.i./ml) for naled. Half of the bioassay mosquitoes were moved directly into clean cages with the other half remaining in the sprayed, hence contaminated, cage. Treatment mortality was assessed at 8, 15, 30, 60, 120, 240, and 1,440 min postapplication. Cage contamination had a significant effect on mosquito mortality for both the LC25 and LC50 between 15 and 30 min postapplication.

[Design and research progress of zero profile cervical Interbody cage].

PubMed

Zhu, Jia; Wang, Song; Liao, Zhenhua; Liu, Weiqiang

2017-02-01

Zero profile cervical interbody cage is an improvement of traditional fusion products and necessary supplement of emerging artificial intervertebral disc products. When applied in Anterior Cervical Decompression Fusion(ACDF), zero profile cervical interbody cage can preserve the advantages of traditional fusion and reduce the incidence of postoperative complications. Moreover, zero profile cervical interbody cage can be applied under the tabu symptoms of Artificial Cervical Disc Replacement(ACDR). This article summarizes zero profile interbody cage products that are commonly recognized and widely used in clinical practice in recent years, and reviews the progress of structure design and material research of zero profile cervical interbody cage products. Based on the latest clinical demands and research progress, this paper also discusses the future development directions of zero profile interbody cage.

Effects of Cage-Change Frequency and Bedding Volume on Mice and Their Microenvironment

PubMed Central

Rosenbaum, Matthew D; VandeWoude, Susan; Johnson, Thomas E

2009-01-01

The frequency at which mouse cages are changed has important implications for the animals, animal care personnel, and facility managers. The objective of this study was to determine how bedding volume and the interval between changes affect microenvironmental conditions, health, and behavior of mice housed in individually ventilated cages (IVC). A total of 15 cages (n = 5 cages per bedding volume) housing ICR female mice (n = 5 animals per cage) were monitored for 17 d. Parameters monitored included clinical evaluation of each animal, appearance of the cage, fecal corticosterone levels, bedding weight, and mouse mass. Atmospheric analysis was performed daily to determine intracage ammonia cage humidity and temperature on a daily basis. Mice were videotaped for 10 min on days 1, 8, and 15, and videos were analyzed for abnormal behaviors. On day 17, 1 mouse from each cage was euthanized, and bronchoalveolar lavage was performed. Statistical differences in parameters were most often noted between low- and high-volume bedding groups. Correlation between visual appearance and actual intracage environmental conditions and mouse health and behavior at specific time points indicated cages that appear dirty to most observers did not have measurably adverse effects on the animals for any of the many parameters evaluated in this study. This study demonstrated that a 2-wk interval between cage changes for ICR female mice housed in IVC caging (with approximately 90 air changes per hour) and aspen chip bedding did not significantly affect measures of animal well-being in this study. This lack of effect occurred despite the appearance of excessive soiling by the 2-wk time point. PMID:19930825

Determinants of acute mortality of Hippodamia convergens (Coleoptera: Coccinellidae) to ultra-low volume permethrin used for mosquito management

PubMed Central

Preftakes, Collin J.; Bodin, Jennifer L.; Brown, Christopher R.; Piccolomini, Alyssa M.; Schleier, Jerome J.

2016-01-01

There are relatively few experimental studies and risk assessments of the effects on non-target insects from ultra-low volume (ULV) insecticides used for management of adult mosquitoes. Therefore, we evaluated factors that may influence the ability of an insect to intercept the insecticide at the time of application by using Hippodamia convergens (Coleoptera: Coccinellidae) in field bioassay experiments in 2011 and 2015. Treatment factors included different distances, two cage heights (ground-level and 1.5 m above ground) to the point of the application, and covered vs. uncovered cage faces (2015 only). Insecticides used included a water-based formulation (Aqua-Reslin®) and an oil-based formulation (Permanone® 30-30) of permethrin. Cage height was highly significant both years, with much less acute (i.e., short-term exposure) mortality at ground-level compared with 1.5 m. In 2011, acute mortality was less at ground-level (mean = 3.2%, median = 0%) compared to 1.5 m (mean = 85.2%, median = 100%). Cage type also was highly significant, with less mortality in covered cages compared to uncovered cages. Mortality by cage height and cage type was as follows: ground level, covered cage (mean = 2.8%, median = 0.1%); ground level, uncovered cage (mean = 41.9%, median = 9.6%); 1.5 m, covered cage (mean = 6.8%, median = 0%); 1.5 m, uncovered cage (mean = 83.7%, median = 100%). Results suggest that acute mortality to non-target insects may vary considerably based on their height and their ability to directly intercept the insecticide as the aerosol passes through the area being sprayed. PMID:27366655

Coordinating subdomains of ferritin protein cages with catalysis and biomineralization viewed from the C4 cage axes.

PubMed

Theil, Elizabeth C; Turano, Paola; Ghini, Veronica; Allegrozzi, Marco; Bernacchioni, Caterina

2014-06-01

Integrated ferritin protein cage function is the reversible synthesis of protein-caged, solid Fe2O3·H2O minerals from Fe(2+) for metabolic iron concentrates and oxidant protection; biomineral order differs in different ferritin proteins. The conserved 432 geometric symmetry of ferritin protein cages parallels the subunit dimer, trimer, and tetramer interfaces, and coincides with function at several cage axes. Multiple subdomains distributed in the self-assembling ferritin nanocages have functional relationships to cage symmetry such as Fe(2+) transport though ion channels (threefold symmetry), biomineral nucleation/order (fourfold symmetry), and mineral dissolution (threefold symmetry) studied in ferritin variants. On the basis of the effects of natural or synthetic subunit dimer cross-links, cage subunit dimers (twofold symmetry) influence iron oxidation and mineral dissolution. 2Fe(2+)/O2 catalysis in ferritin occurs in single subunits, but with cooperativity (n = 3) that is possibly related to the structure/function of the ion channels, which are constructed from segments of three subunits. Here, we study 2Fe(2+) + O2 protein catalysis (diferric peroxo formation) and dissolution of ferritin Fe2O3·H2O biominerals in variants with altered subunit interfaces for trimers (ion channels), E130I, and external dimer surfaces (E88A) as controls, and altered tetramer subunit interfaces (L165I and H169F). The results extend observations on the functional importance of structure at ferritin protein twofold and threefold cage axes to show function at ferritin fourfold cage axes. Here, conserved amino acids facilitate dissolution of ferritin-protein-caged iron biominerals. Biological and nanotechnological uses of ferritin protein cage fourfold symmetry and solid-state mineral properties remain largely unexplored.

Coordinating Subdomains of Ferritin Protein Cages with Catalysis and Biomineralization viewed from the C4 Cage Axes

PubMed Central

Theil, Elizabeth C.; Turano, Paola; Ghini, Veronica; Allegrozzi, Marco; Bernacchioni, Caterina

2014-01-01

Integrated ferritin protein cage function is the reversible synthesis of protein-caged, solid Fe2O3•H2O minerals from Fe2+, for metabolic iron concentrates and oxidant protection; biomineral order varies in different ferritin proteins. The conserved 4, 3, 2 geometric symmetry of ferritin protein cages, parallels subunit dimer, trimer and tetramer interfaces, and coincides with function at several cage axes. Multiple subdomains distributed in the self- assembling ferritin nanocages have functional relationships to cage symmetry such as Fe2+ transport though ion channels (3-fold symmetry), biomineral nucleation/order (4-fold symmetry) and mineral dissolution (3-fold symmetry) studied in ferritin variants. Cage subunit dimers (2-fold symmetry) influence iron oxidation and mineral dissolution, based on effects of natural or synthetic subunit dimer crosslinks. 2Fe2+/O2 catalysis in ferritin occurs in single subunits, but with cooperativity (n=3) that is possibly related to the structure/function of the ion channels, which are constructed from segments of 3 subunits. Here, we study 2Fe2+ + O2 protein catalysis (diferric peroxo formation) and dissolution of ferritin Fe2O3•H2O biominerals in variants with altered subunit interfaces for trimers (ion channels), E130I, and external dimer surfaces (E88A) as controls, and altered tetramer subunit interfaces (L165I and H169F). The results extend observations on the functional importance of structure at ferritin protein 2-fold and 3-fold cage axes to show function at ferritin 4-fold cage axes. Here, conserved amino acids facilitate dissolution of ferritin protein-caged iron biominerals. Biological and nanotechnological uses of ferritin protein cage 4-fold symmetry and solid state mineral properties remain largely unexplored. PMID:24504941

Laser photolysis of caged compounds at 405 nm: photochemical advantages, localisation, phototoxicity and methods for calibration.

PubMed

Trigo, Federico F; Corrie, John E T; Ogden, David

2009-05-30

Rapid, localised photolytic release of neurotransmitters from caged precursors at synaptic regions in the extracellular space is greatly hampered at irradiation wavelengths in the near-UV, close to the wavelength of maximum absorption of the caged precursor, because of inner-filtering by strong absorption of light in the cage solution between the objective and cell. For this reason two-photon excitation is commonly used for photolysis, particularly at multiple points distributed over large fields; or, with near-UV, if combined with local perfusion of the cage. These methods each have problems: the small cross-sections of common cages with two-photon excitation require high cage concentrations and light intensities near the phototoxic limit, while local perfusion gives non-uniform cage concentrations over the field of view. Single-photon photolysis at 405 nm, although less efficient than at 330-350 nm, with present cages is more efficient than two-photon photolysis. The reduced light absorption in the bulk cage solution permits efficient wide-field uncaging at non-toxic intensities with uniform cage concentration. Full photolysis of MNI-glutamate with 100 micros pulses required intensities of 2 mW microm(-2) at the preparation, shown to be non-toxic with repeated exposures. Light scattering at 405 nm was estimated as 50% at 18 microm depth in 21-day rat cerebellum. Methods are described for: (1) varying the laser spot size; (2) photolysis calibration in the microscope with the caged fluorophore NPE-HPTS over the wavelength range 347-405 nm; and (3) determining the point-spread function of excitation. Furthermore, DM-Nitrophen photolysis at 405 nm was efficient for intracellular investigations of Ca2+-dependent processes.

Principal components - Petrology and chemistry of polyphase units in chondritic porous interplanetary dust particles

NASA Astrophysics Data System (ADS)

Rietmeijer, Frans J. M.

1997-03-01

Chondritic porous (CP) interplanetary dust particles (IDPs) can be described as 'cosmic sediments'. It should be possible to recognize in these IDPs the 4500 Myrs old solar nebula dusts. The studies of unaltered chondritic IDPs show that their matrices are a mixture of three different principal components (PCs) that also describe variable C/Si ratios of chondritic IDPs. Among others, PCs include polyphase units (PUs) that are amorphous to holocrystalline, both ultrafine- and coarse-grained, ferromagnesiosilica(te) materials with minor Al and Ca. The properties of PCs and their alteration products define the physical and chemical processes that produced and altered these components. PCs are also cornerstones of IDP classification. For example, the bulk composition of ultrafine-grained PCs can be reconstructed using the 'butterfly method' and also allows an evaluation of the metamorphic signatures, (e.g., dynamic pyrometamorphism), in chondritic IDPs.

A polyphasic taxonomic approach in isolated strains of Cyanobacteria from thermal springs of Greece.

PubMed

Bravakos, Panos; Kotoulas, Georgios; Skaraki, Katerina; Pantazidou, Adriani; Economou-Amilli, Athena

2016-05-01

Strains of Cyanobacteria isolated from mats of 9 thermal springs of Greece have been studied for their taxonomic evaluation. A polyphasic taxonomic approach was employed which included: morphological observations by light microscopy and scanning electron microscopy, maximum parsimony, maximum likelihood and Bayesian analysis of 16S rDNA sequences, secondary structural comparisons of 16S-23S rRNA Internal Transcribed Spacer sequences, and finally environmental data. The 17 cyanobacterial isolates formed a diverse group that contained filamentous, coccoid and heterocytous strains. These included representatives of the polyphyletic genera of Synechococcus and Phormidium, and the orders Oscillatoriales, Spirulinales, Chroococcales and Nostocales. After analysis, at least 6 new taxa at the genus level provide new evidence in the taxonomy of Cyanobacteria and highlight the abundant diversity of thermal spring environments with many potential endemic species or ecotypes. Copyright © 2016 Elsevier Inc. All rights reserved.

Polyphasic approach for differentiating Penicillium nordicum from Penicillium verrucosum.

PubMed

Berni, E; Degola, F; Cacchioli, C; Restivo, F M; Spotti, E

2011-04-01

The aim of this research was to use a polyphasic approach to differentiate Penicillium verrucosum from Penicillium nordicum, to compare different techniques, and to select the most suitable for industrial use. In particular, (1) a cultural technique with two substrates selective for these species; (2) a molecular diagnostic test recently set up and a RAPD procedure derived from this assay; (3) an RP-HPLC analysis to quantify ochratoxin A (OTA) production and (4) an automated system based on fungal carbon source utilisation (Biolog Microstation™) were used. Thirty strains isolated from meat products and originally identified as P. verrucosum by morphological methods were re-examined by newer cultural tests and by PCR methods. All were found to belong to P. nordicum. Their biochemical and chemical characterisation supported the results obtained by cultural and molecular techniques and showed the varied ability in P. verrucosum and P. nordicum to metabolise carbon-based sources and to produce OTA at different concentrations, respectively.

Cyanobacterial diversity in extreme environments in Baja California, Mexico: a polyphasic study.

PubMed

López-Cortés, A; García-Pichel, F; Nübel, U; Vázquez-Juárez, R

2001-12-01

Cyanobacterial diversity from two geographical areas of Baja California Sur, Mexico, were studied: Bahia Concepcion, and Ensenada de Aripez. The sites included hypersaline ecosystems, sea bottom, hydrothermal springs, and a shrimp farm. In this report we describe four new morphotypes, two are marine epilithic from Bahia Concepcion, Dermocarpa sp. and Hyella sp. The third, Geitlerinema sp., occurs in thermal springs and in shrimp ponds, and the fourth, Tychonema sp., is from a shrimp pond. The partial sequences of the 16S rRNA genes and the phylogenetic relationship of four cyanobacterial strains (Synechococcus cf. elongatus, Leptolyngbya cf. thermalis, Leptolyngbya sp., and Geitlerinema sp.) are also presented. Polyphasic studies that include the combination of light microscopy, cultures and the comparative analysis of 16S rRNA gene sequences provide the most powerful approach currently available to establish the diversity of these oxygenic photosynthetic microorganisms in culture and in nature.

Polyphase tectonics at the southern tip of the Manila trench, Mindoro-Tablas Islands, Philippines

NASA Astrophysics Data System (ADS)

Marchadier, Yves; Rangin, Claude

1990-11-01

The southern termination of the Manila trench within the South China Sea continental margin in Mindoro is marked by a complex polyphase tectonic fabric in the arc-trench gap area. Onshore Southern Mindoro the active deformation front of the Manila trench is marked by parallel folds and thrusts, grading southward to N50° W-trending left-lateral strike-slip faults. This transpressive tectonic regime, active at least since the Late Pliocene, has overprinted the collision of an Early Miocene volcanic arc with the South China Sea continental margin (San Jose platform). The collision is postdated by deposition of the Late Miocene-Early Pliocene elastics of the East Mindoro basin. The tectonic and geological framework of this arc, which overlies a metamorphic basement and Eocene elastics, suggests that it was built on a drifted block of the South China Sea continental margin.

Segmental kyphosis after cervical interbody fusion with stand-alone polyetheretherketone (PEEK) cages: a comparative study on 2 different PEEK cages.

PubMed

Kim, Chi Heon; Chung, Chun Kee; Jahng, Tae-Ahn; Park, Sung Bae; Sohn, Seil; Lee, Sungjoon

2015-02-01

Retrospective comparative study. Two polyetheretherketone (PEEK) cages of different designs were compared in terms of the postoperative segmental kyphosis after anterior cervical discectomy and fusion. Segmental kyphosis occasionally occurs after the use of a stand-alone cage for anterior cervical discectomy and fusion. Although PEEK material seems to have less risk of segmental kyphosis compared with other materials, the occurrence of segmental kyphosis for PEEK cages has been reported to be from 0% to 29%. There have been a few reports that addressed the issue of PEEK cage design. A total of 41 consecutive patients who underwent single-level anterior discectomy and fusion with a stand-alone cage were included. Either a round tube-type (Solis; 18 patients, S-group) or a trapezoidal tube-type (MC+; 23 patients, M-group) cage was used. The contact area between the cage and the vertebral body is larger in MC+ than in Solis, and anchoring pins were present in the Solis cage. The effect of the cage type on the segmental angle (SA) (lordosis vs. kyphosis) at postoperative month 24 was analyzed. Preoperatively, segmental lordosis was present in 12/18 S-group and 16/23 M-group patients (P=0.84). The SA was more lordotic than the preoperative angle in both groups just after surgery, with no difference between groups (P=0.39). At 24 months, segmental lordosis was observed in 9/18 S-group and 20/23 M-group patients (P=0.01). The patients in M-group were 7.83 times more likely than patients in S-group (P=0.04; odds ratio, 7.83; 95% confidence interval, 1.09-56.28) not to develop segmental kyphosis. The design of the PEEK cage used may influence the SA, and this association needs to be considered when using stand-alone PEEK cages.

The Impact of Cage Dimensions, Positioning, and Side of Approach in Extreme Lateral Interbody Fusion.

PubMed

Alimi, Marjan; Lang, Gernot; Navarro-Ramirez, Rodrigo; Perrech, Moritz; Berlin, Connor; Hofstetter, Christoph P; Moriguchi, Yu; Elowitz, Eric; Härtl, Roger

2018-02-01

This is a retrospective single-center study. The aim of the study was to evaluate the impact of cage characteristics and position toward clinical and radiographic outcome measures in patients undergoing extreme lateral interbody fusion (ELIF). ELIF is utilized for indirect decompression and minimally invasive surgical treatment for various degenerative spinal disorders. However, evidence regarding the influence of cage characteristics in patient outcome is minimal. Patients undergoing ELIF between 2007 and 2011 were included in a retrospective study. Demographic and perioperative data, as well as cage characteristics and side of approach were extracted. Radiographic parameters including lumbar lordosis, foraminal height, and disc height as well as clinical outcome parameters (Oswestry Disability Index and Visual Analog Scale) were measured preoperatively, postoperatively, and at the latest follow-up examination. Cage dimensions, in situ position, and type were correlated with radiographic and clinical outcome parameters. In total, 84 patients with a total of 145 functional spinal units were analyzed. At the last follow-up of 17.7 months, radiographic and clinical outcome measures revealed significant improvement compared with before surgery with both, 18 and 22 mm cage anterior-posterior diameter subgroups (P≤0.05). Among cage characteristics, 22 mm cages presented superior restoration of foraminal and disc heights compared with 18 mm cages (P≤0.05). Neither position of the cage (anterior vs. posterior), nor the type (parallel vs. lordotic) had a significant impact on restoration of foraminal height and lumbar lordosis. Moreover, the side of surgical approach did not influence the amount of foraminal height increase. Cage anterior-posterior diameter is the determining factor in restoration of foraminal height in ELIF. Cage height, type, positioning, and side of approach do not have a determining role in radiographic outcome in the present study. Sustainable foraminal height restoration is achieved by implantation of wider cages. Level 3.

Effect of 2 Bedding Materials on Ammonia Levels in Individually Ventilated Cages

PubMed Central

Koontz, Jason M; Kumsher, David M; III, Richard Kelly; Stallings, Jonathan D

2016-01-01

This study sought to identify an optimal rodent bedding and cage-change interval to establish standard procedures for the IVC in our rodent vivarium. Disposable cages were prefilled with either corncob or α-cellulose bedding and were used to house 2 adult Sprague–Dawley rats (experimental condition) or contained no animals (control). Rats were observed and intracage ammonia levels measured daily for 21 d. Intracage ammonia accumulation became significant by day 8 in experimental cages containing α-cellulose bedding, whereas experimental cages containing corncob bedding did not reach detectable levels of ammonia until day 14. In all 3 experimental cages containing α-cellulose, ammonia exceeded 100 ppm (our maximum acceptable limit) by day 11. Two experimental corncob cages required changing at days 16 and 17, whereas the remaining cage containing corncob bedding lasted the entire 21 d without reaching the 100-ppm ammonia threshold. These data suggests that corncob bedding provides nearly twice the service life of α-cellulose bedding in the IVC system. PMID:26817976

Effect of 2 Bedding Materials on Ammonia Levels in Individually Ventilated Cages.

PubMed

Koontz, Jason M; Kumsher, David M; Kelly, Richard; Stallings, Jonathan D

2016-01-01

This study sought to identify an optimal rodent bedding and cage-change interval to establish standard procedures for the IVC in our rodent vivarium. Disposable cages were prefilled with either corncob or α-cellulose bedding and were used to house 2 adult Sprague-Dawley rats (experimental condition) or contained no animals (control). Rats were observed and intracage ammonia levels measured daily for 21 d. Intracage ammonia accumulation became significant by day 8 in experimental cages containing α-cellulose bedding, whereas experimental cages containing corncob bedding did not reach detectable levels of ammonia until day 14. In all 3 experimental cages containing α-cellulose, ammonia exceeded 100 ppm (our maximum acceptable limit) by day 11. Two experimental corncob cages required changing at days 16 and 17, whereas the remaining cage containing corncob bedding lasted the entire 21 d without reaching the 100-ppm ammonia threshold. These data suggests that corncob bedding provides nearly twice the service life of α-cellulose bedding in the IVC system.

A Pseudo-Atomic Model of the COPII Cage Obtained from CryoEM and Mass Spectrometry Analyses

PubMed Central

Noble, Alex J.; Zhang, Qian; O’Donnell, Jason; Hariri, Hanaa; Bhattacharya, Nilakshee; Marshall, Alan G.

2012-01-01

COPII vesicles transport proteins from the ER to the Golgi apparatus. Previous cryoEM structures of the COPII cage lacked the resolution necessary to determine the residues of Sec13 and Sec31 that mediate assembly and flexibility of the COPII cage. Here we present a 12Å-resolution structure of the COPII cage, where the tertiary structure of Sec13 and Sec31 is clearly identifiable. We employ this structure and a homology model of the Sec13-Sec31 complex to create a reliable pseudo-atomic model of the COPII cage. We combined this model with hydrogen/deuterium exchange mass spectrometry analysis to characterize four distinct contact regions at the vertices of the COPII cage. Furthermore, we found that the 2-fold symmetry of the Sec31 dimeric region of Sec13-31 is broken on cage formation, and that the resulting hinge is essential to form the proper edge geometry in COPII cages. PMID:23262493

A library of protein cage architectures as nanomaterials.

PubMed

Flenniken, M L; Uchida, M; Liepold, L O; Kang, S; Young, M J; Douglas, T

2009-01-01

Virus capsids and other structurally related cage-like proteins such as ferritins, dps, and heat shock proteins have three distinct surfaces (inside, outside, interface) that can be exploited to generate nanomaterials with multiple functionality by design. Protein cages are biological in origin and each cage exhibits extremely homogeneous size distribution. This homogeneity can be used to attain a high degree of homogeneity of the templated material and its associated property. A series of protein cages exhibiting diversity in size, functionality, and chemical and thermal stabilities can be utilized for materials synthesis under a variety of conditions. Since synthetic approaches to materials science often use harsh temperature and pH, it is an advantage to utilize protein cages from extreme environments. In this chapter, we review recent studies on discovering novel protein cages from harsh natural environments such as the acidic thermal hot springs at Yellowstone National Park (YNP) and on utilizing protein cages as nano-scale platforms for developing nanomaterials with wide range of applications from electronics to biomedicine.

Assessment of biomarkers for contaminants of emerging concern on aquatic organisms downstream of a municipal wastewater discharge.

PubMed

Jasinska, Edyta J; Goss, Greg G; Gillis, Patricia L; Van Der Kraak, Glen J; Matsumoto, Jacqueline; de Souza Machado, Anderson A; Giacomin, Marina; Moon, Thomas W; Massarsky, Andrey; Gagné, Francois; Servos, Mark R; Wilson, Joanna; Sultana, Tamanna; Metcalfe, Chris D

2015-10-15

Contaminants of emerging concern (CECs), including pharmaceuticals, personal care products and estrogens, are detected in wastewater treatment plant (WWTP) discharges. However, analytical monitoring of wastewater and surface water does not indicate whether CECs are affecting the organisms downstream. In this study, fathead minnows (Pimephales promelas) and freshwater mussels Pyganodon grandis Say, 1829 (synonym: Anodonta grandis Say, 1829) were caged for 4 weeks in the North Saskatchewan River, upstream and downstream of the discharge from the WWTP that serves the Edmonton, AB, Canada. Passive samplers deployed indicated that concentrations of pharmaceuticals, personal care products, an estrogen (estrone) and an androgen (androstenedione) were elevated at sites downstream of the WWTP discharge. Several biomarkers of exposure were significantly altered in the tissues of caged fathead minnows and freshwater mussels relative to the upstream reference sites. Biomarkers altered in fish included induction of CYP3A metabolism, an increase in vitellogenin (Vtg) gene expression in male minnows, elevated ratios of oxidized to total glutathione (i.e. GSSG/TGSH), and an increase in the activity of antioxidant enzymes (i.e. glutathione reductase, glutathione-S-transferase). In mussels, there were no significant changes in biomarkers of oxidative stress and the levels of Vtg-like proteins were reduced, not elevated, indicating a generalized stress response. Immune function was altered in mussels, as indicated by elevated lysosomal activity per hemocyte in P. grandis caged closest to the wastewater discharge. This immune response may be due to exposure to bacterial pathogens in the wastewater. Multivariate analysis indicated a response to the CECs Carbamazepine (CBZ) and Trimethoprim (TPM). Overall, these data indicate that there is a 1 km zone of impact for aquatic organisms downstream of WWTP discharge. However, multiple stressors in municipal wastewater make measurement and interpretation of impact of CECs difficult since water temperature, conductivity and bacteria are also inducing biomarker responses in both fish and mussels. Copyright © 2015 Elsevier B.V. All rights reserved.

Promoter-level expression clustering identifies time development of transcriptional regulatory cascades initiated by ErbB receptors in breast cancer cells.

PubMed

Mina, Marco; Magi, Shigeyuki; Jurman, Giuseppe; Itoh, Masayoshi; Kawaji, Hideya; Lassmann, Timo; Arner, Erik; Forrest, Alistair R R; Carninci, Piero; Hayashizaki, Yoshihide; Daub, Carsten O; Okada-Hatakeyama, Mariko; Furlanello, Cesare

2015-07-16

The analysis of CAGE (Cap Analysis of Gene Expression) time-course has been proposed by the FANTOM5 Consortium to extend the understanding of the sequence of events facilitating cell state transition at the level of promoter regulation. To identify the most prominent transcriptional regulations induced by growth factors in human breast cancer, we apply here the Complexity Invariant Dynamic Time Warping motif EnRichment (CIDER) analysis approach to the CAGE time-course datasets of MCF-7 cells stimulated by epidermal growth factor (EGF) or heregulin (HRG). We identify a multi-level cascade of regulations rooted by the Serum Response Factor (SRF) transcription factor, connecting the MAPK-mediated transduction of the HRG stimulus to the negative regulation of the MAPK pathway by the members of the DUSP family phosphatases. The finding confirms the known primary role of FOS and FOSL1, members of AP-1 family, in shaping gene expression in response to HRG induction. Moreover, we identify a new potential regulation of DUSP5 and RARA (known to antagonize the transcriptional regulation induced by the estrogen receptors) by the activity of the AP-1 complex, specific to HRG response. The results indicate that a divergence in AP-1 regulation determines cellular changes of breast cancer cells stimulated by ErbB receptors.

Volume rather than flow incentive spirometry is effective in improving chest wall expansion and abdominal displacement using optoelectronic plethysmography.

PubMed

Paisani, Denise de Moraes; Lunardi, Adriana Claudia; da Silva, Cibele Cristine Berto Marques; Porras, Desiderio Cano; Tanaka, Clarice; Carvalho, Celso Ricardo Fernandes

2013-08-01

Incentive spirometers are widely used in clinical practice and classified as flow-oriented (FIS) and volume-oriented (VIS). Until recently the respiratory inductive plethysmography used to evaluate the effects of incentive spirometry on chest wall mechanics presented limitations, which may explain why the impact of VIS and FIS remains poorly known. To compare the effects of VIS and FIS on thoracoabdominal mechanics and respiratory muscle activity in healthy volunteers. This cross-sectional trial assessed 20 subjects (12 female, ages 20-40 years, body mass index 20-30 kg/m(2)). All subjects performed 8 quiet breaths and 8 deep breaths with FIS and VIS, in a randomized order. We measured thoracoabdominal chest wall, upper and lower rib-cage, and abdominal volumes with optoelectronic plethysmography, and the muscle activity of the sternocleidomastoid and superior and inferior intercostal muscles with electromyography. VIS increased chest wall volume more than did FIS (P = .007) and induced a larger increase in the upper and lower rib-cages and abdomen (156%, 91%, and 151%, respectively, P < .001). By contrast, FIS induced more activity in the accessory muscles of respiration than did VIS (P < .001). VIS promotes a greater increase in chest wall volume, with a larger abdominal contribution and lower respiratory muscle activity, than does FIS in healthy adults.

The Evolution of the Cup-Cage Technique for Major Acetabular Defects: Full and Half Cup-Cage Reconstruction.

PubMed

Sculco, Peter K; Ledford, Cameron K; Hanssen, Arlen D; Abdel, Matthew P; Lewallen, David G

2017-07-05

Complex acetabular reconstruction for major bone loss can require advanced methods such as the use of a cup-cage construct. The purpose of this study was to review outcomes after the initial development of the cup-cage technique and the subsequent evolution to the use of a half cup-cage construct. We performed a retrospective, single-center review of 57 patients treated with cup-cage reconstruction for major acetabular bone loss. All patients had major acetabular defects graded as Paprosky Type 2B through 3B, with 34 (60%) having an associated pelvic discontinuity. Thirty patients received a full cup-cage construct and 27, a half cup-cage construct. The mean follow-up was 5 years. Both the full and half cup-cage cohorts demonstrated significantly improved Harris hip score (HHS) values, from 36 to 72 at a minimum of 2 years of follow-up (p < 0.05). Early construct migration occurred in 4 patients, with stabilization prior to 2-year follow-up in all but 1 patient. Incomplete, zone-3, nonprogressive acetabular radiolucencies were observed in 2 (7%) of the full cup-cage constructs and 6 (22%) of the half cup-cage constructs. One patient with a full cup-cage construct underwent re-revision of the acetabular component for progressive migration and aseptic loosening. Short-term survivorship free from re-revision for any cause or reoperation was 89% (83% and 96% for full and half cup-cage cohorts, respectively). Both full and half cup-cage constructs demonstrated successful clinical outcomes and survivorship in the treatment of major acetabular defects and pelvic discontinuity. Each method is utilized on the basis of individual intraoperative findings, including the extent and pattern of bone loss, the quality and location of host bone remaining after preparation, and the presence of pelvic discontinuity. Longer-term follow-up is required to understand the durability of these constructs in treating major acetabular defects and pelvic discontinuity. Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

Caged compounds: tools for illuminating neuronal responses and connections.

PubMed

Nerbonne, J M

1996-06-01

A number of new 'caged' intracellular second messengers and neurotransmitters have been developed using the photolabile o-nitrobenzyl group. This chemistry has also recently been exploited in novel ways, including the development of caged enzyme substrates and caged proteins. Although caged compounds continue to be used primarily for mechanistic (kinetic) studies of processes mediated by transmitters or second messengers, the spatial resolution afforded by the use of light to effect changes in transmitter concentrations has now been clearly demonstrated. The increased availability of caged compounds and of the technologies required to exploit them provides neurobiologists with powerful tools for probing neuronal response properties and connectivity patterns.

Caged Molecular Glues as Photoactivatable Tags for Nuclear Translocation of Guests in Living Cells.

PubMed

Arisaka, Akio; Mogaki, Rina; Okuro, Kou; Aida, Takuzo

2018-02-21

We developed dendritic caged molecular glues ( Caged Glue-R) as tags for nucleus-targeted drug delivery, whose multiple guanidinium ion (Gu + ) pendants are protected by an anionic photocleavable unit (butyrate-substituted nitroveratryloxycarbonyl; BA NVOC). Negatively charged Caged Glue-R hardly binds to anionic biomolecules because of their electrostatic repulsion. However, upon exposure of Caged Glue-R to UV light or near-infrared (NIR) light, the BA NVOC groups of Caged Glue-R are rapidly detached to yield an uncaged molecular glue ( Uncaged Glue-R) that carries multiple Gu + pendants. Because Gu + forms a salt bridge with PO 4 - , Uncaged Glue-R tightly adheres to anionic biomolecules such as DNA and phospholipids in cell membranes by a multivalent salt-bridge formation. When tagged with Caged Glue-R, guests can be taken up into living cells via endocytosis and hide in endosomes. However, when the Caged Glue-R tag is photochemically uncaged to form Uncaged Glue-R, the guests escape from the endosome and migrate into the cytoplasm followed by the cell nucleus. We demonstrated that quantum dots (QDs) tagged with Caged Glue-R can be delivered efficiently to cell nuclei eventually by irradiation with light.

Application of the independent molecule model to elucidate the dynamics of structure I methane hydrate: a third report.

PubMed

Yoshioki, Shuzo

2009-01-01

Two new model systems of methane hydrate, larger than the previous systems, are constructed. One consists of 63 small and large cages with a small cage at the centre. The other has 65 small and large cages with a large cage at the centre. Three different H-bonding network patterns between water are formed, and three random orientations of methane in each cage are chosen. Using the surface water fixed method, we obtained the energy minimum conformations, fitted to the X-ray crystallographic structure. With normal mode analysis, we calculated frequencies of 2915.1 cm(-1) for a small cage, and 2911.0 cm(-1) for a large cage. These frequencies are a little nearer to the Raman spectra than were previous model systems. Treating three force constants of anharmonic potential energy and the strength of H-bonding between methane and water as four parameters, we obtained frequencies of 2913.6 cm(-1) for a small cage, a little lower than the Raman, and 2906.6 cm(-1) for a large cage, a little higher than the Raman. The calculations thus almost reach the Raman spectra.

Virucidal effects of rodent cage-cleaning practices on the viability of adenovirus vectors.

PubMed

Porter, Jacqueline D; Lyons, Russette M

2002-09-01

Human adenoviruses and adenoviral vectors are classified as Risk Group 2 agents and require BSL2 containment and practices. An additional consideration in using adenoviruses and viral vectors in laboratory animal studies is the possible transmission of these agents to other animals and/or personnel as a result of viral shedding in animal urine and feces. When handling BSL2 agents, cage-wash staff are required to wear appropriate personnel protective equipment, including scrubs, Tyvek suit, hair covering, dust mask, shoes covers, and gloves. Current decontamination procedures are to bag and autoclave soiled rodent cages containing bedding prior to washing in the cage washer to prevent possible adenoviral transmission. However, the practice of autoclaving softens the polycarbonate-based rodent cages, allowing damaging agents or conditions to affect the integrity of the plastic and degrade the cages. The objective of this study was to determine whether current rodent cage-cleaning practices produced virucidal effects for use in lieu of or prior to autoclaving the cages. We found that heating an Av3GFP vector in a test tube to a temperature of 74 degrees C (165 degrees F) for 6 min conditions equivalent to those of the cage washer resulted in greater than an 11-log reduction in infectivity of the vector as evaluated by its cytopathic effect on cells. The combination of heating and a liquid, phosphate-free alkaline detergent produced the same reduction in vector infectivity. However, common cage-cleaning solutions alone possessed no virucidal activity. The high temperatures used in cage-washing procedures alone or in combination with a cleaning solution reduced or eliminated the risk of transmission from viral shedding through urine and feces even at vector concentrations far greater than would ever be expected to be present. Autoclaving cages diminishes the stability and integrity of the polycarbonate cages without providing a further reduction in the risk of virus or vector transmission. On the basis of results from this study, new cage-wash recommendations include dumping the contaminated bedding into a HEPA-filtered waste disposal system and autoclaving the bags of bedding before disposal, then cleaning the cages in the rack washer at wash temperatures of 74 degrees C (165 F) and rinse temperatures of 82 degrees C (180 F).

[Detection of alcoholism in the medical office: applicability of the CAGE questionnaire by the practicing physician. Group of Medical Practitioners PMU].

PubMed

Perdrix, A; Decrey, H; Pécoud, A; Burnand, B; Yersin, B

1995-09-23

The general practitioner (GP) plays a very important role in early detection of alcoholism. Clinical evaluation is often the only method used, although it has been suggested that any systematic patient history should include the CAGE test. We compare the effectiveness of these two approaches and attempt to determine the applicability of the CAGE test in a general practitioner's usual practice. 12 GPs took part in this study during 6 months. They looked for possible alcohol abuse in each new patient by a standard patient history and clinical examination. Patients were randomized into 2 groups, one of which was given the CAGE test and the other not. For each patient in the CAGE group the applicability of the test was quantified by the GP. 416 patients were included; 214 were randomized into the "CAGE group" and 202 into the control group. On a clinical basis, 15 patients in the control group and 16 in the "CAGE group" (14 men, 2 women) were suspected of alcohol abuse. The CAGE test was positive in 15 patients (7%); among these, 6 were not suspect on a clinical basis. In patients aged 18-34, the detection rate of alcohol-related problems more than doubled when the CAGE test was used. The age of the patients influenced performance of the CAGE test and clinical evaluation. Only 2% of women had a positive CAGE test. Administration of the CAGE test was considered easy in 112 patients and average to difficult in 50, while the test was inapplicable with 52 patients. The latter proportion was higher than that observed in institutions (hospitals, outpatient departments) of the same region. Applicability was influenced neither by the sex nor the age of the patients, but varied greatly according to the physician (from 38% to 100%). The CAGE test increases the number of patients detected with alcohol problems by 37% and seems to be especially useful when administered to young people. The number of women with alcohol problems is probably underestimated by both clinical evaluation and the CAGE test. Furthermore, physicians in private practice are more reluctant to use the CAGE test systematically than those in a public institution.

A high-precision instrument for analyzing nonlinear dynamic behavior of bearing cage.

PubMed

Yang, Z; Chen, H; Yu, T; Li, B

2016-08-01

The high-precision ball bearing is fundamental to the performance of complex mechanical systems. As the speed increases, the cage behavior becomes a key factor in influencing the bearing performance, especially life and reliability. This paper develops a high-precision instrument for analyzing nonlinear dynamic behavior of the bearing cage. The trajectory of the rotational center and non-repetitive run-out (NRRO) of the cage are used to evaluate the instability of cage motion. This instrument applied an aerostatic spindle to support and spin test the bearing to decrease the influence of system error. Then, a high-speed camera is used to capture images when the bearing works at high speeds. A 3D trajectory tracking software tema Motion is used to track the spot which marked the cage surface. Finally, by developing the matlab program, a Lissajous' figure was used to evaluate the nonlinear dynamic behavior of the cage with different speeds. The trajectory of rotational center and NRRO of the cage with various speeds are analyzed. The results can be used to predict the initial failure and optimize cage structural parameters. In addition, the repeatability precision of instrument is also validated. In the future, the motorized spindle will be applied to increase testing speed and image processing algorithms will be developed to analyze the trajectory of the cage.

A high-precision instrument for analyzing nonlinear dynamic behavior of bearing cage

NASA Astrophysics Data System (ADS)

Yang, Z.; Chen, H.; Yu, T.; Li, B.

2016-08-01

The high-precision ball bearing is fundamental to the performance of complex mechanical systems. As the speed increases, the cage behavior becomes a key factor in influencing the bearing performance, especially life and reliability. This paper develops a high-precision instrument for analyzing nonlinear dynamic behavior of the bearing cage. The trajectory of the rotational center and non-repetitive run-out (NRRO) of the cage are used to evaluate the instability of cage motion. This instrument applied an aerostatic spindle to support and spin test the bearing to decrease the influence of system error. Then, a high-speed camera is used to capture images when the bearing works at high speeds. A 3D trajectory tracking software tema Motion is used to track the spot which marked the cage surface. Finally, by developing the matlab program, a Lissajous' figure was used to evaluate the nonlinear dynamic behavior of the cage with different speeds. The trajectory of rotational center and NRRO of the cage with various speeds are analyzed. The results can be used to predict the initial failure and optimize cage structural parameters. In addition, the repeatability precision of instrument is also validated. In the future, the motorized spindle will be applied to increase testing speed and image processing algorithms will be developed to analyze the trajectory of the cage.

Biomechanical Evaluation of a Novel Apatite-Wollastonite Ceramic Cage Design for Lumbar Interbody Fusion: A Finite Element Model Study

PubMed Central

Şenköylü, Alpaslan; Aktaş, Erdem; Sarıkaya, Baran; Sipahioğlu, Serkan; Gürbüz, Rıza; Timuçin, Muharrem

2018-01-01

Objectives Cage design and material properties play a crucial role in the long-term results, since interbody fusions using intervertebral cages have become one of the basic procedures in spinal surgery. Our aim is to design a novel Apatite-Wollastonite interbody fusion cage and evaluate its biomechanical behavior in silico in a segmental spinal model. Materials and Methods Mechanical properties for the Apatite-Wollastonite bioceramic cages were obtained by fitting finite element results to the experimental compression behavior of a cage prototype. The prototype was made from hydroxyapatite, pseudowollastonite, and frit by sintering. The elastic modulus of the material was found to be 32 GPa. Three intact lumbar vertebral segments were modelled with the ANSYS 12.0.1 software and this model was modified to simulate a Posterior Lumbar Interbody Fusion. Four cage designs in different geometries were analyzed in silico under axial loading, flexion, extension, and lateral bending. Results The K2 design had the best overall biomechanical performance for the loads considered. Maximum cage stress recorded was 36.7 MPa in compression after a flexion load, which was within the biomechanical limits of the cage. Conclusion Biomechanical analyses suggest that K2 bioceramic cage is an optimal design and reveals essential material properties for a stable interbody fusion. PMID:29581974

A high-precision instrument for analyzing nonlinear dynamic behavior of bearing cage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Z., E-mail: zhaohui@nwpu.edu.cn; Yu, T.; Chen, H.

2016-08-15

The high-precision ball bearing is fundamental to the performance of complex mechanical systems. As the speed increases, the cage behavior becomes a key factor in influencing the bearing performance, especially life and reliability. This paper develops a high-precision instrument for analyzing nonlinear dynamic behavior of the bearing cage. The trajectory of the rotational center and non-repetitive run-out (NRRO) of the cage are used to evaluate the instability of cage motion. This instrument applied an aerostatic spindle to support and spin test the bearing to decrease the influence of system error. Then, a high-speed camera is used to capture images whenmore » the bearing works at high speeds. A 3D trajectory tracking software TEMA Motion is used to track the spot which marked the cage surface. Finally, by developing the MATLAB program, a Lissajous’ figure was used to evaluate the nonlinear dynamic behavior of the cage with different speeds. The trajectory of rotational center and NRRO of the cage with various speeds are analyzed. The results can be used to predict the initial failure and optimize cage structural parameters. In addition, the repeatability precision of instrument is also validated. In the future, the motorized spindle will be applied to increase testing speed and image processing algorithms will be developed to analyze the trajectory of the cage.« less

Evaluation of cage micro-environment of mice housed on various types of bedding materials

USGS Publications Warehouse

Smith, E.; Stockwell, J.D.; Schweitzer, I.; Langley, S.H.; Smith, A.L.

2004-01-01

A variety of environmental factors can affect the outcomes of studies using laboratory rodents. One such factor is bedding. Several new bedding materials and processing methods have been introduced to the market in recent years, but there are few reports of their performance. In the studies reported here, we have assessed the cage micro-environment (in-cage ammonia levels, temperature, and humidity) of mice housed on various kinds of bedding and their combinations. We also compared results for bedding supplied as Nestpaks versus loose bedding. We studied C57BL/6J mice (commonly used) and NOD/LtJ mice (heavy soilers) that were maintained, except in one study, in static duplex cages. In general, we observed little effect of bedding type on in-cage temperature or humidity; however, there was considerable variation in ammonia concentrations. The lowest ammonia concentrations occurred in cages housing mice on hardwood bedding or a mixture of corncob and alpha cellulose. In one experiment comparing the micro-environments of NOD/LtJ male mice housed on woodpulp fiber bedding in static versus ventilated caging, we showed a statistically significant decrease in ammonia concentrations in ventilated cages. Therefore, our data show that bedding type affects the micro-environment in static cages and that effects may differ for ventilated cages, which are being used in vivaria with increasing frequency.

Investigation of large-area multicoil inductively coupled plasma sources using three-dimensional fluid model

NASA Astrophysics Data System (ADS)

Brcka, Jozef

2016-07-01

A multi inductively coupled plasma (ICP) system can be used to maintain the plasma uniformity and increase the area processed by a high-density plasma. This article presents a source in two different configurations. The distributed planar multi ICP (DM-ICP) source comprises individual ICP sources that are not overlapped and produce plasma independently. Mutual coupling of the ICPs may affect the distribution of the produced plasma. The integrated multicoil ICP (IMC-ICP) source consists of four low-inductance ICP antennas that are superimposed in an azimuthal manner. The identical geometry of the ICP coils was assumed in this work. Both configurations have highly asymmetric components. A three-dimensional (3D) plasma model of the multicoil ICP configurations with asymmetric features is used to investigate the plasma characteristics in a large chamber and the operation of the sources in inert and reactive gases. The feasibility of the computational calculation, the speed, and the computational resources of the coupled multiphysics solver are investigated in the framework of a large realistic geometry and complex reaction processes. It was determined that additional variables can be used to control large-area plasmas. Both configurations can form a plasma, that azimuthally moves in a controlled manner, the so-called “sweeping mode” (SM) or “polyphase mode” (PPM), and thus they have the potential for large-area and high-density plasma applications. The operation in the azimuthal mode has the potential to adjust the plasma distribution, the reaction chemistry, and increase or modulate the production of the radicals. The intrinsic asymmetry of the individual coils and their combined operation were investigated within a source assembly primarily in argon and CO gases. Limited investigations were also performed on operation in CH4 gas. The plasma parameters and the resulting chemistry are affected by the geometrical relation between individual antennas. The aim of this work is to incorporate the technological, computational, dimensional scaling, and reaction chemistry aspects of the plasma under one computational framework. The 3D simulation is utilized to geometrically scale up the reactive plasma that is produced by multiple ICP sources.

Porous titanium-6 aluminum-4 vanadium cage has better osseointegration and less micromotion than a poly-ether-ether-ketone cage in sheep vertebral fusion.

PubMed

Wu, Su-Hua; Li, Yi; Zhang, Yong-Quan; Li, Xiao-Kang; Yuan, Chao-Fan; Hao, Yu-Lin; Zhang, Zhi-Yong; Guo, Zheng

2013-12-01

Interbody fusion cages made of poly-ether-ether-ketone (PEEK) have been widely used in clinics for spinal disorders treatment; however, they do not integrate well with surrounding bone tissue. Ti-6Al-4V (Ti) has demonstrated greater osteoconductivity than PEEK, but the traditional Ti cage is generally limited by its much greater elastic modulus (110 GPa) than natural bone (0.05-30 GPa). In this study, we developed a porous Ti cage using electron beam melting (EBM) technique to reduce its elastic modulus and compared its spinal fusion efficacy with a PEEK cage in a preclinical sheep anterior cervical fusion model. A porous Ti cage possesses a fully interconnected porous structure (porosity: 68 ± 5.3%; pore size: 710 ± 42 μm) and a similar Young's modulus as natural bone (2.5 ± 0.2 GPa). When implanted in vivo, the porous Ti cage promoted fast bone ingrowth, achieving similar bone volume fraction at 6 months as the PEEK cage without autograft transplantation. Moreover, it promoted better osteointegration with higher degree (2-10x) of bone-material binding, demonstrated by histomorphometrical analysis, and significantly higher mechanical stability (P < 0.01), shown by biomechanical testing. The porous Ti cage fabricated by EBM could achieve fast bone ingrowth. In addition, it had better osseointegration and superior mechanical stability than the conventional PEEK cage, demonstrating great potential for clinical application. © 2013 Wiley Periodicals, Inc. and International Center for Artificial Organs and Transplantation.

Influence of the ionic liquid [C4mpy][Tf2N] on the structure of the miniprotein Trp-cage.

PubMed

Baker, Joseph L; Furbish, Jeffrey; Lindberg, Gerrick E

2015-11-01

We examine the effect of the ionic liquid [C4mpy][Tf2N] on the structure of the miniprotein Trp-cage and contrast these results with the behavior of Trp-cage in water. We find the ionic liquid has a dramatic effect on Trp-cage, though many similarities with aqueous Trp-cage are observed. We assess Trp-cage folding by monitoring root mean square deviation from the crystallographic structure, radius of gyration, proline cis/trans isomerization state, protein secondary structure, amino acid contact formation and distance, and native and non-native contact formation. Starting from an unfolded configuration, Trp-cage folds in water at 298 K in less than 500 ns of simulation, but has very little mobility in the ionic liquid at the same temperature, which can be ascribed to the higher ionic liquid viscosity. At 365 K, the mobility of the ionic liquid is increased and initial stages of Trp-cage folding are observed, however Trp-cage does not reach the native folded state in 2 μs of simulation in the ionic liquid. Therefore, in addition to conventional molecular dynamics, we also employ scaled molecular dynamics to expedite sampling, and we demonstrate that Trp-cage in the ionic liquid does closely approach the aqueous folded state. Interestingly, while the reduced mobility of the ionic liquid is found to restrict Trp-cage motion, the ionic liquid does facilitate proline cis/trans isomerization events that are not seen in our aqueous simulations. Copyright © 2015 Elsevier Inc. All rights reserved.

50 CFR 648.77 - Cage identification.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Atlantic Surf Clam and Ocean Quahog Fisheries § 648.77 Cage identification. Except as provided in § 648.78... for surfclams and ocean quahogs: (a) Tagging. Before offloading, all cages that contain surfclams or... Administrator. (g) Transfer. See § 648.74(b)(2). (h) Presumptions. Surfclams and ocean quahogs found in cages...

50 CFR 648.77 - Cage identification.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Atlantic Surf Clam and Ocean Quahog Fisheries § 648.77 Cage identification. Except as provided in § 648.78... for surfclams and ocean quahogs: (a) Tagging. Before offloading, all cages that contain surfclams or... Administrator. (g) Transfer. See § 648.74(b)(2). (h) Presumptions. Surfclams and ocean quahogs found in cages...

50 CFR 648.77 - Cage identification.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Atlantic Surf Clam and Ocean Quahog Fisheries § 648.77 Cage identification. Except as provided in § 648.78... for surfclams and ocean quahogs: (a) Tagging. Before offloading, all cages that contain surfclams or... Administrator. (g) Transfer. See § 648.74(b)(2). (h) Presumptions. Surfclams and ocean quahogs found in cages...

Analysis of c-Fos induction in response to social interaction in male and female Fisher 344 rats.

PubMed

Perkins, Amy E; Woodruff, Elizabeth R; Chun, Lauren E; Spencer, Robert L; Varlinskaya, Elena; Deak, Terrence

2017-10-01

Sex differences in the expression of social behavior are typically apparent in adolescent and adult rats. While the neurobiology underlying juvenile social play behavior has been well characterized, less is known about discrete brain regions involved in adult responsiveness to a same sex peer. Furthermore, whether adult males and females differ in their responsiveness to a social interaction in terms of neuronal activation indexed via immediate early gene (IEG) expression remains to be determined. Thus, the present study was designed to identify key sites relevant to the processing of sensory stimuli (generally) or social stimuli (specifically) after brief exposure to a same-sex social partner by assessing IEG expression. Four-month-old male and female Fisher (F) 344 rats (N=38; n=5-8/group) were either left undisturbed in their home cage as controls (HCC), exposed to a testing context alone for 30min (CXT), or were placed in the context for 20min and then allowed to socially interact (SI) with a sex-matched conspecific for 10min. Females demonstrated greater levels of social behavior, relative to males. Analysis of c-Fos induction revealed that females exhibited greater c-Fos expression in the prefrontal cortex, regardless of condition. In many brain regions, induction was similar in the CXT and SI groups. However, in the bed nucleus of the stria terminalis (BNST), females exhibited greater c-Fos induction in response to the social interaction relative to their male counterparts, indicating a sex difference in responsivity to social stimuli. Taken together, these data suggest that the BNST is a sexually dimorphic region in terms of activation in response to social stimuli. Copyright © 2017 Elsevier B.V. All rights reserved.

Using a PFET To Commutate an SCR

NASA Technical Reports Server (NTRS)

Edwards, D. B.; Ripple, W. E.

1984-01-01

Accidental turn-on prevented. PFET diverts load current around SCR to prevent false SCR triggering from current and voltage switching transients. New circuit used in all types of single phase and polyphase inverters and in buck-boost-, and flyback regulators.

Incorporation of organometallic Ru complexes into apo-ferritin cage.

PubMed

Takezawa, Yusuke; Böckmann, Philipp; Sugi, Naoki; Wang, Ziyue; Abe, Satoshi; Murakami, Tatsuya; Hikage, Tatsuo; Erker, Gerhard; Watanabe, Yoshihito; Kitagawa, Susumu; Ueno, Takafumi

2011-03-14

Spherical protein cages such as an iron storage protein, ferritin, have great potential as nanometer-scale capsules to assemble and store metal ions and complexes. We report herein the synthesis of a composite of an apo-ferritin cage and Ru(p-cymene) complexes. Ru complexes were efficiently incorporated into the ferritin cavity without degradation of its cage structure. X-Ray crystallography revealed that the Ru complexes were immobilized on the interior surface of the cage mainly by the coordination of histidine residues.

Fast and accurate spectral estimation for online detection of partial broken bar in induction motors

NASA Astrophysics Data System (ADS)

Samanta, Anik Kumar; Naha, Arunava; Routray, Aurobinda; Deb, Alok Kanti

2018-01-01

In this paper, an online and real-time system is presented for detecting partial broken rotor bar (BRB) of inverter-fed squirrel cage induction motors under light load condition. This system with minor modifications can detect any fault that affects the stator current. A fast and accurate spectral estimator based on the theory of Rayleigh quotient is proposed for detecting the spectral signature of BRB. The proposed spectral estimator can precisely determine the relative amplitude of fault sidebands and has low complexity compared to available high-resolution subspace-based spectral estimators. Detection of low-amplitude fault components has been improved by removing the high-amplitude fundamental frequency using an extended-Kalman based signal conditioner. Slip is estimated from the stator current spectrum for accurate localization of the fault component. Complexity and cost of sensors are minimal as only a single-phase stator current is required. The hardware implementation has been carried out on an Intel i7 based embedded target ported through the Simulink Real-Time. Evaluation of threshold and detectability of faults with different conditions of load and fault severity are carried out with empirical cumulative distribution function.

Soybean defense responses to the soybean aphid.

PubMed

Li, Yan; Zou, Jijun; Li, Min; Bilgin, Damla D; Vodkin, Lila O; Hartman, Glen L; Clough, Steven J

2008-01-01

Transcript profiles in aphid (Aphis glycines)-resistant (cv. Dowling) and -susceptible (cv. Williams 82) soybean (Glycine max) cultivars using soybean cDNA microarrays were investigated. Large-scale soybean cDNA microarrays representing approx. 18 000 genes or c. 30% of the soybean genome were compared at 6 and 12 h post-application of aphids. In a separate experiment utilizing clip cages, expression of three defense-related genes were examined at 6, 12, 24, 48, and 72 h in both cultivars by quantitative real-time PCR. One hundred and forty genes showed specific responses for resistance; these included genes related to cell wall, defense, DNA/RNA, secondary metabolism, signaling and other processes. When an extended time period of sampling was investigated, earlier and greater induction of three defense-related genes was observed in the resistant cultivar; however, the induction declined after 24 or 48 h in the resistant cultivar but continued to increase in the susceptible cultivar after 24 h. Aphid-challenged resistant plants showed rapid differential gene expression patterns similar to the incompatible response induced by avirulent Pseudomonas syringae. Five genes were identified as differentially expressed between the two genotypes in the absence of aphids.

Compensation for Harmonic Currents and Reactive Power in Wind Power Generation System using PWM Inverter

NASA Astrophysics Data System (ADS)

Shinohara, Katsuji; Shinhatsubo, Kurato; Iimori, Kenichi; Yamamoto, Kichiro; Saruban, Takamichi; Yamaemori, Takahiro

In recent year, consciousness of environmental problems is enhancing, and the price of the electric power purchased by an electric power company is established expensive for the power plant utilizing the natural energy. So, the introduction of the wind power generation is promoted in Japan. Generally, squirrel-cage induction machines are widely used as a generator in wind power generation system because of its small size, lightweight and low-cost. However, the induction machines do not have a source of excitation. Thus, it causes the inrush currents and the instantaneous voltage drop when the generator is directly connected to a power grid. To reduce the inrush currents, an AC power regulator is used. Wind power generations are frequently connected to and disconnected from the power grid. However, when the inrush currents are reduced, harmonic currents are caused by phase control of the AC power regulator. And the phase control of AC power regulator cannot control the power factor. Therefore, we propose the use of the AC power regulator to compensate for the harmonic currents and reactive power in the wind power generation system, and demonstrate the validity of its system by simulated and experimental results.

Dynamic characteristics of motor-gear system under load saltations and voltage transients

NASA Astrophysics Data System (ADS)

Bai, Wenyu; Qin, Datong; Wang, Yawen; Lim, Teik C.

2018-02-01

In this paper, a dynamic model of a motor-gear system is proposed. The model combines a nonlinear permeance network model (PNM) of a squirrel-cage induction motor and a coupled lateral-torsional dynamic model of a planetary geared rotor system. The external excitations including voltage transients and load saltations, as well as the internal excitations such as spatial effects, magnetic circuits topology and material nonlinearity in the motor, and time-varying mesh stiffness and damping in the planetary gear system are considered in the proposed model. Then, the simulation results are compared with those predicted by the electromechanical model containing a dynamic motor model with constant inductances. The comparison showed that the electromechanical system model with the PNM motor model yields more reasonable results than the electromechanical system model with the lumped-parameter electric machine. It is observed that electromechanical coupling effect can induce additional and severe gear vibrations. In addition, the external conditions, especially the voltage transients, will dramatically affect the dynamic characteristics of the electromechanical system. Finally, some suggestions are offered based on this analysis for improving the performance and reliability of the electromechanical system.

Effects of an Extended Cage-change Interval on Ammonia Levels and Reproduction in Mongolian Gerbils (Meriones unguiculatus).

PubMed

McCullagh, Elizabeth A; McCullagh, Peter; Klug, Achim; Leszczynski, Jori K; Fong, Derek L

2017-11-01

Prompted by the cage cleanliness of Mongolian gerbils (Meriones unguiculatus), we evaluated a prolonged cage-change interval. We compared the effects of a 2-wk and 6-wk cage-change schedule on ammonia levels, temperature, humidity, and reproductive performance in breeding pairs housed in IVC. We hypothesized that ammonia levels would remain below our threshold for cage changing and that reproductive performance would not be affected. Although ammonia levels increased over time, they remained low (less than 5 ppm) over the 6-wk period. In addition, the 6-wk cage-change interval did not significantly influence reproductive parameters, such as average pup weaning weight, number of litters, and number of pups per litter. We conclude that an extended cage-change interval (6-wk) can be used for gerbils without significant increases in intracage ammonia levels or effects on reproduction.

Blower augmentor for power oil and power gas burners

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fisher, L.A.

1987-07-14

An oil burner is described in combination: (a) a blower comprising a scroll housing and a driven squirrel cage, the squirrel cage having an interior air space, and having blades disposed around space and constituting an air impeller; (b) the scroll housing having a tangential air outlet, and further comprising a spiral wall encircling the squirrel cage; (c) a stationary barrier wall mounted in the housing and extending into the interior air space of the squirrel cage. The barrier wall extends outward from and with respect to a central axial area of the squirrel cage to a location adjacent themore » blades; (d) the housing is wider than the squirrel cage in axial dimension, to provide an end space between the squirrel cage and the housing, in which end space air tends to recirculate in the housing; and (e) support and baffle means disposed in the end space between the housing and squirrel cage, for mounting the barrier wall and for redirecting in outward directions a portion of the circularly travelling recirculating air in the housing.« less

Testing and Comparative Evaluation of Space Shuttle Main Engine Flowmeter Bearings

NASA Technical Reports Server (NTRS)

Hissam, Andy; Leberman, Mike; McLeroy, Rick

2005-01-01

This paper provides a summary of testing of Space Shuttle Main Engine (SSME) flowmeter bearings and cage material. These tests were con&cM over a several month period in 2004 at the Marshall Space Flight Center. The test program's primary objective was to compare the performance of bearings using the existing cage material and bearings using a proposed replacement cage material. In order to meet the test objectives for this program, a flowmeter test rig was designed and fabricated to measure both breakaway and running torque for a flowmeter assembly. Other test parameters,,such as motor current and shaft speed, were also recorded and provide a means of comparing bearing performance. The flowmeter and bearings were tested in liquid hydrogen to simulate the flowmeter's operating environment as closely as possible. Based on the results from this testing, the bearings with the existing cage material are equivalent to the bearings with the proposed replacement cage material. No major differences exist between the old and new cage materials. Therefore, the new cage material is a suitable replacement for the existing cage material.

Synthesis, structural characterisation and magnetic studies of polymetallic iron phosphonate cages.

PubMed

Khanra, Sumit; Helliwell, Madeleine; Tuna, Floriana; McInnes, Eric J L; Winpenny, Richard E P

2009-08-21

Four new polymetallic iron(III) phosphonate cages have been made and structurally characterised. These are an octanuclear cage [Fe(8)O(3)(OH)(2)(O(2)C(t)Bu)(11)(PhCH(2)PO(3))(3)(py)(3)], a decanuclear cage [Fe(10)O(2)(OH)(8)(O(2)C(t)Bu)(10)(PhCH(2)PO(3))(4)(pip)(2)], a heterometallic cage [Fe(6)Li(5)(mu(3)-O)(2)((t)BuPO(3))(6)(O(2)C(t)Bu)(8)(MeOH)(2)(Py)(4)] and a tridecanuclear cage [Et(3)NH](2)[Fe(13)(mu(3)-O)(3)(mu(2)-OH)(7)((t)BuPO(3))(7)(Me(3)CCO(2))(14)(H(2)O)] (pip = piperidine, py = pyridine). Magnetic studies of the first three compounds show anti-ferromagnetic exchange between the iron(III) centers leading to diamagnetic ground states for the homometallic cages. For the heterometallic cage, the six Fe(III) centers are arranged in two triangles, and each triangle has an S = 1/2 spin ground state.

Development of High Temperature Electro-Magnetic Actuators (HTEMA) for Aircraft Propulsion Systems (Preprint)

DTIC Science & Technology

2013-05-01

an 18 inch gap diameter has roughly a 2 foot outer diameter                                                              2 “ Brushless  Permanent...require PMs include wound rotor DC (brush and brushless ), Variable or Switched reluctance (VR or SR) machines and squirrel cage induction motors...Trades have identified Brushless DC PM and SR machines are of primary interest. Both motors can use sensorless commutation methods. A VR resolver can

Controllable fabrication of ultrafine oblique organic nanowire arrays and their application in energy harvesting

NASA Astrophysics Data System (ADS)

Zhang, Lu; Cheng, Li; Bai, Suo; Su, Chen; Chen, Xiaobo; Qin, Yong

2015-01-01

Ultrafine organic nanowire arrays (ONWAs) with a controlled direction were successfully fabricated by a novel one-step Faraday cage assisted plasma etching method. The mechanism of formation of nanowire arrays is proposed; the obliquity and aspect ratio can be accurately controlled from approximately 0° to 90° via adjusting the angle of the sample and the etching time, respectively. In addition, the ONWAs were further utilized to improve the output of the triboelectric nanogenerator (TENG). Compared with the output of TENG composed of vertical ONWAs, the open-circuit voltage, short-circuit current and inductive charges were improved by 73%, 150% and 98%, respectively. This research provides a convenient and practical method to fabricate ONWAs with various obliquities on different materials, which can be used for energy harvesting.

Controllable fabrication of ultrafine oblique organic nanowire arrays and their application in energy harvesting.

PubMed

Zhang, Lu; Cheng, Li; Bai, Suo; Su, Chen; Chen, Xiaobo; Qin, Yong

2015-01-28

Ultrafine organic nanowire arrays (ONWAs) with a controlled direction were successfully fabricated by a novel one-step Faraday cage assisted plasma etching method. The mechanism of formation of nanowire arrays is proposed; the obliquity and aspect ratio can be accurately controlled from approximately 0° to 90° via adjusting the angle of the sample and the etching time, respectively. In addition, the ONWAs were further utilized to improve the output of the triboelectric nanogenerator (TENG). Compared with the output of TENG composed of vertical ONWAs, the open-circuit voltage, short-circuit current and inductive charges were improved by 73%, 150% and 98%, respectively. This research provides a convenient and practical method to fabricate ONWAs with various obliquities on different materials, which can be used for energy harvesting.

Integral inverter/battery charger for use in electric vehicles

NASA Technical Reports Server (NTRS)

Thimmesch, D.

1983-01-01

The design and test results of a thyristor based inverter/charger are discussed. A battery charger is included integral to the inverter by using a subset of the inverter power circuit components. The resulting charger provides electrical isolation between the vehicle propulsion battery and ac line and is capable of charging a 25 kWh propulsion battery in 8 hours from a 220 volt ac line. The integral charger employs the inverter commutation components at a resonant ac/dc isolated converter rated at 3.6 kW. Charger efficiency and power factor at an output power of 3.6 kW are 86% and 95% respectively. The inverter, when operated with a matching polyphase ac induction motor and nominal 132 volt propulsion battery, can provide a peak shaft power of 34 kW (45 ph) during motoring operation and 45 kW (60 hp) during regeneration. Thyristors are employed for the inverter power switching devices and are arranged in an input-commutated topology. This configuration requires only two thyristors to commutate the six main inverter thyristors. Inverter efficiency during motoring operation at motor shaft speeds above 450 rad/sec (4300 rpm) is 92-94% for output power levels above 11 KW (15 hp). The combined ac inverter/charger package weighs 47 kg (103 lbs).

Intracage ammonia levels in static and individually ventilated cages housing C57BL/6 mice on 4 bedding substrates.

PubMed

Ferrecchia, Christie E; Jensen, Kelly; Van Andel, Roger

2014-03-01

The relationship among ammonia levels, cage-changing frequency, and bedding types is an important and potentially controversial topic in the laboratory animal science community. Some bedding options may not provide sufficient urine absorption and bacterial regulation to minimize ammonia production during the interval between cage changes. High intracage ammonia levels can cause subclinical degeneration and inflammation of nasal passages, rhinitis and olfactory epithelial necrosis in exposed mice. Here we sought to compare the effects of 4 commonly used bedding substrates (1/4-in. irradiated corncob, reclaimed wood pulp, aspen wood chips, and recycled newspaper) on ammonia generation when housing female C57BL/6 mice in static and individually ventilated caging. Intracage ammonia levels were measured daily for 1 wk (static cage experiment) or 2 wk (IVC experiment). The results of this study suggest that the corncob, aspen wood chip, and recycled newspaper beddings that we tested are suitable for once-weekly cage changing for static cages and for changing every 2 wk for IVC. However, ammonia levels were not controlled appropriately in cages containing reclaimed wood pulp bedding, and pathologic changes occurred within 1 wk in the nares of mice housed on this bedding in static cages.

Intracage Ammonia Levels in Static and Individually Ventilated Cages Housing C57BL/6 Mice on 4 Bedding Substrates

PubMed Central

Ferrecchia, Christie E; Jensen, Kelly; Andel, Roger Van

2014-01-01

The relationship among ammonia levels, cage-changing frequency, and bedding types is an important and potentially controversial topic in the laboratory animal science community. Some bedding options may not provide sufficient urine absorption and bacterial regulation to minimize ammonia production during the interval between cage changes. High intracage ammonia levels can cause subclinical degeneration and inflammation of nasal passages, rhinitis and olfactory epithelial necrosis in exposed mice. Here we sought to compare the effects of 4 commonly used bedding substrates (1/4-in. irradiated corncob, reclaimed wood pulp, aspen wood chips, and recycled newspaper) on ammonia generation when housing female C57BL/6 mice in static and individually ventilated caging. Intracage ammonia levels were measured daily for 1 wk (static cage experiment) or 2 wk (IVC experiment). The results of this study suggest that the corncob, aspen wood chip, and recycled newspaper beddings that we tested are suitable for once-weekly cage changing for static cages and for changing every 2 wk for IVC. However, ammonia levels were not controlled appropriately in cages containing reclaimed wood pulp bedding, and pathologic changes occurred within 1 wk in the nares of mice housed on this bedding in static cages. PMID:24602540

Finite element analysis and cadaveric cinematic analysis of fixation options for anteriorly implanted trabecular metal interbody cages.

PubMed

Berjano, Pedro; Blanco, Juan Francisco; Rendon, Diego; Villafañe, Jorge Hugo; Pescador, David; Atienza, Carlos Manuel

2015-11-01

To assess, with finite element analysis and an in vitro biomechanical study in cadaver, whether the implementation of an anterior interbody cage made of hedrocel with nitinol shape memory staples in compression increases the stiffness of the stand-alone interbody cage and to compare these constructs' stiffness to other constructs common in clinical practice. A biomechanical study with a finite element analysis and cadaveric testing assessed the stiffness of different fixation modes for the L4-L5 functional spinal unit: intact spine, destabilized spine with discectomy, posterior pedicle-screw fixation, anterior stand-alone interbody cage, anterior interbody cage with bilateral pedicle screws and anterior interbody cage with two shape memory staples in compression. These modalities of vertebral fixation were compared in four loading modes (flexion, extension, lateral bending, and axial rotation). The L4-L5 spinal unit with an anterior interbody cage and two staples was stiffer than the stand-alone cage. The construct stiffness was similar to that of a model of posterior pedicular stabilization. The stiffness was lower than that of the anterior cage plus bilateral pedicle-screw fixation. The use of an anterior interbody implant with shape memory staples in compression may be an alternative to isolated posterior fixation and to anterior isolated implants, with increased stiffness.

Investigation of instability, dynamic forces, and effect of dynamic loading on strength of cages for the bearings in the high pressure oxygen turbopumps for the space shuttle main engine

NASA Technical Reports Server (NTRS)

Dufrane, K. F.; Kannel, J. W.; Merriman, T. L.; Rosenfield, A. R.

1985-01-01

Experiments were performed to determine the effect of cyclic loading on bearing cage strength. A long term working tensile load of approximately 1300 N (300 lbs) was found to be the likely maximum. Higher loads caused a decrease in cage tensile strength after the 125,000 cycle testing period. Poisson's ratio in compression was found to be highly dependent upon the direction of the fiberglass plies. At room temperature the value was 0.15 with the plies and 0.68 across the plies. At -196 C (-321 F), the value with the plies was 0.20. The results of the analyses conducted have again demonstrated the critical need for improved lubrication in the high pressure oxygen turbopump bearings. Lubricant films with low shear strength and low friction coefficients promote cage stability and decrease ball/cage forces during marginal operating conditions. The analysis of the effect of combined bearing loads on ball/cage loads has identified a radial load of 3600 N (800 lbs) as the maximum for the current clearance of the balls and cage pockets. Liquid oxygen impinging on the cage in the direction of rotation was found to enhance cage stability.

Improved Synthesis of Caged Glutamate and Caging Each Functional Group.

PubMed

Guruge, Charitha; Ouedraogo, Yannick P; Comitz, Richard L; Ma, Jingxuan; Losonczy, Attila; Nesnas, Nasri

2018-05-25

Glutamate is an excitatory neurotransmitter that controls numerous pathways in the brain. Neuroscientists make use of photoremovable protecting groups, also known as cages, to release glutamate with precise spatial and temporal control. Various cage designs have been developed and among the most effective has been the nitroindolinyl caging of glutamate. We, hereby, report an improved synthesis of one of the current leading molecules of caged glutamate, 4-carboxymethoxy-5,7-dinitroindolinyl glutamate (CDNI-Glu), which possesses efficiencies with the highest reported quantum yield of at least 0.5. We present the shortest route, to date, for the synthesis of CDNI-Glu in 4 steps, with a total reaction time of 40 h and an overall yield of 20%. We also caged glutamate at the other two functional groups, thereby, introducing two new cage designs: α-CDNI-Glu and N-CDNI-Glu. We included a study of their photocleavage properties using UV-vis, NMR, as well as a physiology experiment of a two-photon uncaging of CDNI-Glu in acute hippocampal brain slices. The newly introduced cage designs may have the potential to minimize the interference that CDNI-Glu has with the GABA A receptor. We are broadly disseminating this to enable neuroscientists to use these photoactivatable tools.

Impact of Room Ventilation Rates on Mouse Cage Ventilation and Microenvironment.

PubMed

Reeb, Carolyn K.; Jones, Robert B.; Bearg, David W.; Bedigian, Hendrick; Paigen, Beverly

1997-01-01

To assess the impact of room ventilation on animal cage microenvironment, intracage ventilation rate, temperature, humidity, and concentrations of carbon dioxide and ammonia were monitored in nonpressurized, bonnet-topped mouse cages. Cages on the top, middle, and bottom rows of a mouse rack were monitored at room ventilation rates of 0, 5, 10, and 20 air changes/h (ACH). Ventilation inside the animal cage increased somewhat from 12.8 to 18.9 ACH as room ventilation rate in- creased from 0 to 20 ACH, but the differences were not statistically significant, and most of the increase occurred in cages in the top row nearest to the fresh air supply. Cages containing mice had ventilation rate between 10 and 15 ACH even when room ventilation was reduced to 0 ACH; this ventilation is a result of the thermal heat load of the mice. After 6 days of soiled bedding, intracage ammonia concentration was c 3 ppm at all room ventilation rates and was not affected by increasing room ventilation. Temperature inside cages did not change with increasing ventilation. Humidity inside cages significantly decreased with increasing ventilation, from 55% relative humidity at 5 ACH to 36% relative humidity at 20 ACH. Carbon dioxide concentration decreased from 2,500 ppm to 1,900 ppm when ventilation rate increased from 5 ACH to 10 ACH, but no further significant decrease was observed at 20 ACH. In conclusion, increasing the room ventilation rate higher than 5 ACH did not result in significant improvements in the cage microenvironment.

Effect of nest design, passages, and hybrid on use of nest and production performance of layers in furnished cages.

PubMed

Wall, H; Tauson, R; Elwinger, K

2002-03-01

Production performance, including egg quality, and proportion of eggs laid in nests were studied in furnished experimental cages incorporating nests, litter baths, and perches. The study comprised a total of 972 hens of two genotypes: Lohmann Selected Leghorn (LSL) and Hy-Line White. The birds were studied from 20 to 80 wk of age, and conventional four-hen cages were included as a reference. In furnished cages for six hens, the effects of 30 or 50% vs. 100% nest bottom lining (Astro turf) were studied with LSL hens. Nest bottom lining had no significant effect on egg production or proportions of cracked or dirty eggs, but the use of nests was significantly higher in cages incorporating nests with 100% lining, compared with 50 or 30%. The two hybrids were compared when housed in large, group-furnished cages for 14 or 16 hens of two designs; with a rear partition with two pop holes or fully open, i.e., no rear partition. LSL birds produced significantly better and had a significantly lower proportion of cracked eggs. There was no difference between H- and O-cages, either in production or in egg quality. LSL birds laid a significantly lower proportion of eggs in the nests, especially in O-cages, implying a significant hybrid x cage interaction. When housed in conventional cages, the hybrids did not differ in proportion of cracked eggs but differed in production traits. It was concluded that with the present nest design, the proportion of nest bottom lining cannot be reduced without affecting birds' use of nests, but the proportion did not affect exterior egg quality. The effect of genotype should be considered in the further development of furnished cages.

Effect of cage design, supplemental posterior instrumentation and approach on primary stability of a lumbar interbody fusion - A biomechanical in vitro study.

PubMed

Schmoelz, Werner; Sandriesser, Sabrina; Loebl, Oded; Bauer, Marlies; Krappinger, Dietmar

2017-10-01

There are various techniques and approaches for lumbar interbody fusion differing in access, cage type and type of supplemental posterior instrumentation. While a transforaminal access usually includes a hemifacetectomy, the facet joint can be preserved with a more lateral extraforaminal access. The supplemental posterior instrumentation required for both fusion techniques is still debated. The purpose of the present study was to compare primary stability of the two accesses for two different cage types with none, unilateral and bilateral supplemental posterior instrumentation. Six monosegmental lumbar functional spinal units (FSUs) were included in each of the two groups, and subjected to a flexibility test. As cages, a newly designed cage was compared to a standard cage in the following states: (a) native, (b) stand-alone cage, (c) bilateral internal fixator, (d) unilateral internal fixator, (e) unilateral facetectomy+bilateral internal fixator, (f) unilateral facetectomy+unilateral internal fixator and (g) unilateral facetectomy with stand-alone cage. For comparison the range of motion was normalized to the native state and the effects of the facetectomy, cage type, and supplemental instrumentation was compared. Within the subject comparison showed a significantly higher flexibility for the unilateral facetectomy in all motion directions (p<0.001). In between subject comparison showed a significant effect of cage type on flexibility in flexion/extension (p=0.002) and lateral bending (p=0.028) but not in axial rotation (p=0.322). The type of supplemental posterior fixation had a significant effect on the flexibility in all motion directions (stand-alone>unilateral fixator>bilateral fixator). Cage design and approach type are affecting the primary stability of lumbar interbody fusion procedures while the type of posterior instrumentation is the most influencing factor. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tissue engineering rib with the incorporation of biodegradable polymer cage and BMSCs/decalcified bone: an experimental study in a canine model.

PubMed

Tang, Hua; Wu, Bin; Qin, Xiong; Zhang, Lu; Kretlow, Jim; Xu, Zhifei

2013-05-20

The reconstruction of large bone defects, including rib defects, remains a challenge for surgeons. In this study, we used biodegradable polydioxanone (PDO) cages to tissue engineer ribs for the reconstruction of 4cm-long costal defects. PDO sutures were used to weave 6cm long and 1cm diameter cages. Demineralized bone matrix (DBM) which is a xenograft was molded into cuboids and seeded with second passage bone marrow mesenchymal stem cells (BMSCs) that had been osteogenically induced. Two DBM cuboids seeded with BMSCs were put into the PDO cage and used to reconstruct the costal defects. Radiographic examination including 3D reconstruction, histologic examination and mechanical test was performed after 24 postoperative weeks. All the experimental subjects survived. In all groups, the PDO cage had completely degraded after 24 weeks and been replaced by fibrous tissue. Better shape and radian were achieved in PDO cages filled with DBM and BMSCs than in the other two groups (cages alone, or cages filled with acellular DBM cuboids). When the repaired ribs were subjected to an outer force, the ribs in the PDO cage/DBMs/BMSCs group kept their original shape while ribs in the other two groups deformed. In the PDO cage/DBMs/BMSCs groups, we also observed bony union at all the construct interfaces while there was no bony union observed in the other two groups. This result was also confirmed by radiographic and histologic examination. This study demonstrates that biodegradable PDO cage in combination with two short BMSCs/DBM cuboids can repair large rib defects. The satisfactory repair rate suggests that this might be a feasible approach for large bone repair.

Tissue engineering rib with the incorporation of biodegradable polymer cage and BMSCs/decalcified bone: an experimental study in a canine model

PubMed Central

2013-01-01

Background The reconstruction of large bone defects, including rib defects, remains a challenge for surgeons. In this study, we used biodegradable polydioxanone (PDO) cages to tissue engineer ribs for the reconstruction of 4cm-long costal defects. Methods PDO sutures were used to weave 6cm long and 1cm diameter cages. Demineralized bone matrix (DBM) which is a xenograft was molded into cuboids and seeded with second passage bone marrow mesenchymal stem cells (BMSCs) that had been osteogenically induced. Two DBM cuboids seeded with BMSCs were put into the PDO cage and used to reconstruct the costal defects. Radiographic examination including 3D reconstruction, histologic examination and mechanical test was performed after 24 postoperative weeks. Results All the experimental subjects survived. In all groups, the PDO cage had completely degraded after 24 weeks and been replaced by fibrous tissue. Better shape and radian were achieved in PDO cages filled with DBM and BMSCs than in the other two groups (cages alone, or cages filled with acellular DBM cuboids). When the repaired ribs were subjected to an outer force, the ribs in the PDO cage/DBMs/BMSCs group kept their original shape while ribs in the other two groups deformed. In the PDO cage/DBMs/BMSCs groups, we also observed bony union at all the construct interfaces while there was no bony union observed in the other two groups. This result was also confirmed by radiographic and histologic examination. Conclusions This study demonstrates that biodegradable PDO cage in combination with two short BMSCs/DBM cuboids can repair large rib defects. The satisfactory repair rate suggests that this might be a feasible approach for large bone repair. PMID:23688344

Dyspnea, chest wall hyperinflation, and rib cage distortion in exercising patients with chronic obstructive pulmonary disease.

PubMed

Bruni, Giulia Innocenti; Gigliotti, Francesco; Binazzi, Barbara; Romagnoli, Isabella; Duranti, Roberto; Scano, Giorgio

2012-06-01

Whether dyspnea, chest wall dynamic hyperinflation, and abnormalities of rib cage motion are interrelated phenomena has not been systematically evaluated in patients with chronic obstructive pulmonary disease (COPD). Our hypothesis that they are not interrelated was based on the following observations: (i) externally imposed expiratory flow limitation is associated with no rib cage distortion during strenuous incremental exercise, with indexes of hyperinflation not being correlated with dyspnea, and (ii) end-expiratory chest wall volume may either increase or decrease during exercise in patients with COPD, with those who hyperinflate being as breathless as those who do not. Sixteen patients breathed either room air or 50% supplemental O2 at 75% of peak exercise in randomized order. We evaluated the volume of chest wall (V(cw)) and its compartments: the upper rib cage (V(rcp)), lower rib cage (V(rca)), and abdomen (V(ab)) using optoelectronic plethysmography; rib cage distortion was assessed by measuring the phase angle shift between V(rcp) and V(rca). Ten patients increased end-expiratory V(cw) (V(cw,ee)) on air. In seven hyperinflators and three non-hyperinflators, the lower rib cage paradoxed inward during inspiration with a phase angle of 63.4° ± 30.7° compared with a normal phase angle of 16.1° ± 2.3° recorded in patients without rib cage distortion. Dyspnea (by Borg scale) averaged 8.2 and 9 at the end of exercise on air in patients with and without rib cage distortion, respectively. At iso-time during exercise with oxygen, decreased dyspnea was associated with a decrease in ventilation regardless of whether patients distorted the rib cage, dynamically hyperinflated, or deflated the chest wall. Dyspnea, chest wall dynamic hyperinflation, and rib cage distortion are not interrelated phenomena.

The Impact of Environmental Light Intensity on Experimental Tumor Growth.

PubMed

Suckow, Mark A; Wolter, William R; Duffield, Giles E

2017-09-01

Cancer research requires for consistent models that minimize environmental variables. Within the typical laboratory animal housing facility, animals may be exposed to varying intensities of light as a result of cage type, cage position, light source, and other factors; however, studies evaluating the differential effect of light intensity during the light phase on tumor growth are lacking. The effect of cage face light intensity, as determined by cage rack position was evaluated with two tumor models using the C57Bl/6NHsd mouse and transplantable B16F10 melanoma cells or Lewis lung carcinoma (LLC) cells. Animals were housed in individually-ventilated cages placed at the top, middle, or bottom of the rack in a diagonal pattern so that the top cage was closest to the ceiling light source, and cage face light intensity was measured. Following a two-week acclimation period at the assigned cage position, animals were subcutaneously administered either 1.3×10 6 B16F10 melanoma cells or 2.5×10 5 Lewis lung carcinoma cells. Weights of excised tumors were measured following euthanasia 18 days (melanoma) or 21 days (LCC) after tumor cell administration. Cage face light intensity was significantly different depending on the location of the cage, with cages closest to the light source have the greatest intensity. Mean tumor weights were significantly less (p<0.001 for melanoma; p≤0.01 for LCC) in middle light intensity mice compared to high and low light intensity mice. The environmental light intensity to which experimental animals are exposed may vary markedly with cage location and can significantly influence experimental tumor growth, thus supporting the idea that light intensity should be controlled as an experimental variable for animals used in cancer research. Copyright© 2017, International Institute of Anticancer Research (Dr. George J. Delinasios), All rights reserved.

Maternal antibody transfer to broiler progeny varies among strains and is affected by grain source and cage density.

PubMed

Leandro, N M; Ali, R; Koci, M; Moraes, V; Eusebio-Balcazar, P E; Jornigan, J; Malheiros, R D; Wineland, M J; Brake, J; Oviedo-Rondón, E O

2011-12-01

Two experiments were conducted to examine the effects of broiler breeder dietary grain source and cage density on maternal antibody (MatAb) transfer to progeny in 2 genetic strains (A and B). Broiler breeders were assigned to 16 litter floor pens and fed either corn- or wheat-based diets. Breeders were administered 4 live vaccines against Newcastle disease virus (NDV). At 23 wk of age, pullets and cocks, which reflected the full BW distribution from each treatment, were moved to a cage breeder house and placed at 1 or 2 hens/cage. Breeders were artificially inseminated at 44 wk (experiment 1) and 52 wk of age (experiment 2). Eggs were collected for 8 d, incubated, and placed in individual pedigree bags at d 19 of incubation. Blood samples from 5 chicks per treatment combination were collected at hatch in both experiments. Spleen and bursa were collected from the same chicks for histomorphometry analyses in experiment 2. In the second experiment, 12 chicks per treatment were placed in cages. Progeny were provided diets based on the same grain (corn or wheat) as their parents. Serum samples were collected at 5, 9, and 13 d of age and analyzed for anti-NDV MatAb. Data were analyzed as a 2 × 2 × 2 factorial design considering strain, dietary grain source, and cage density as main factors. Interaction effects were observed in breeders and progeny. Experiment 1 showed that strain A chicks had lower levels of MatAb when hens were housed at 2 hens/cage rather than 1 hen/cage. The MatAb levels of strain B chickens were not affected by cage density in either experiment. Experiment 2 demonstrated similar effects of cage density on MatAb levels and the area of bursa follicles for both strains. Progeny of breeders fed corn-based diets had smaller spleen white pulp only when hens were housed at 2 hens/cage compared with 1 hen/cage. The results of these experiments suggest that breeder strain and cage-density conditions affected MatAb transfer to progeny and embryo development of spleen and bursa.

Vertebral body fracture after anterior cervical discectomy and fusion with zero-profile anchored cages in adjacent levels: a cautionary tale.

PubMed

Mattei, Tobias A; Teles, Alisson R; Dinh, Dzung H

2016-01-05

Zero-profile (also called self-locking, anchored or stand-alone cages) have been recently proposed as an interesting alternative for anterior cervical discectomy and fusion (ACDF), as they are supposed to reduce the rates of post-operative cage extrusion without necessarily incurring in the additional surgical time and increased rates of dysphagia associated with plating. Nevertheless, the exact indications of zero-profile anchored cages have not yet been established in the literature. To report the first case of a vertebral body fracture between the blades of zero-profile anchored cages after ACDFs in adjacent levels and to review the available literature on hardware-related complications after multi-level ACDFs with zero-profile anchored cages. Case report and systematic literature review. The authors report the first case of a vertebral body fracture between the blades of zero-profile anchored cages after ACDFs in adjacent levels. The patient presented with refractory mechanical neck pain at the 1-month post-operative follow-up, ultimately requiring a posterior instrumented fusion. A comprehensive systematic literature review on the available data regarding the safety, complications as well as radiological and clinical outcomes of zero-profile anchored cages is also performed. In the reported case, the use of zero-profile anchored cages in adjacent levels on the cervical spine led to a fracture of the vertebral body between the cages at the 1-month follow-up, with anterior avulsion of the part of the vertebral body where the blades from the two cages converged. According to the systematic literature review which included 409 patients from 10 different clinical series (with a total cumulative follow-up of approximately 535 patients-year), there were only two reported hardware-related complications after ACDF with zero-profile anchored cages, none of them involving fracture at the level of convergence of blades or screws. Although hardware-related complications after the use of zero-profile anchored cages seem to be rare events, future biomechanical and clinical studies are warranted in order to evaluate the safety of employing such devices for the treatment of multilevel degenerative disc disease in the cervical spine.

Biomechanics of lateral lumbar interbody fusion constructs with lateral and posterior plate fixation: laboratory investigation.

PubMed

Fogel, Guy R; Parikh, Rachit D; Ryu, Stephen I; Turner, Alexander W L

2014-03-01

Lumbar interbody fusion is indicated in the treatment of degenerative conditions. Laterally inserted interbody cages significantly decrease range of motion (ROM) compared with other cages. Supplemental fixation options such as lateral plates or spinous process plates have been shown to provide stability and to reduce morbidity. The authors of the current study investigate the in vitro stability of the interbody cage with a combination of lateral and spinous process plate fixation and compare this method to the established bilateral pedicle screw fixation technique. Ten L1-5 specimens were evaluated using multidirectional nondestructive moments (± 7.5 N · m), with a custom 6 degrees-of-freedom spine simulator. Intervertebral motions (ROM) were measured optoelectronically. Each spine was evaluated under the following conditions at the L3-4 level: intact; interbody cage alone (stand-alone); cage supplemented with lateral plate; cage supplemented with ipsilateral pedicle screws; cage supplemented with bilateral pedicle screws; cage supplemented with spinous process plate; and cage supplemented with a combination of lateral plate and spinous process plate. Intervertebral rotations were calculated, and ROM data were normalized to the intact ROM data. The stand-alone laterally inserted interbody cage significantly reduced ROM with respect to the intact state in flexion-extension (31.6% intact ROM, p < 0.001), lateral bending (32.5%, p < 0.001), and axial rotation (69.4%, p = 0.002). Compared with the stand-alone condition, addition of a lateral plate to the interbody cage did not significantly alter the ROM in flexion-extension (p = 0.904); however, it was significantly decreased in lateral bending and axial rotation (p < 0.001). The cage supplemented with a lateral plate was not statistically different from bilateral pedicle screws in lateral bending (p = 0.579). Supplemental fixation using a spinous process plate was not significantly different from bilateral pedicle screws in flexion-extension (p = 0.476). The combination of lateral plate and spinous process plate was not statistically different from the cage supplemented with bilateral pedicle screws in all the loading modes (p ≥ 0.365). A combination of lateral and spinous process plate fixation to supplement a laterally inserted interbody cage helps achieve rigidity in all motion planes similar to that achieved with bilateral pedicle screws.

Protein cages and synthetic polymers: a fruitful symbiosis for drug delivery applications, bionanotechnology and materials science.

PubMed

Rother, Martin; Nussbaumer, Martin G; Renggli, Kasper; Bruns, Nico

2016-11-07

Protein cages are hollow protein nanoparticles, such as viral capsids, virus-like particles, ferritin, heat-shock proteins and chaperonins. They have well-defined capsule-like structures with a monodisperse size. Their protein subunits can be modified by genetic engineering at predetermined positions, allowing for example site-selective introduction of attachment points for functional groups, catalysts or targeting ligands on their outer surface, in their interior and between subunits. Therefore, protein cages have been extensively explored as functional entities in bionanotechnology, as drug-delivery or gene-delivery vehicles, as nanoreactors or as templates for the synthesis of organic and inorganic nanomaterials. The scope of functionalities and applications of protein cages can be significantly broadened if they are combined with synthetic polymers on their surface or within their interior. For example, PEGylation reduces the immunogenicity of protein cage-based delivery systems and active targeting ligands can be attached via polymer chains to favour their accumulation in diseased tissue. Polymers within protein cages offer the possibility of increasing the loading density of drug molecules, nucleic acids, magnetic resonance imaging contrast agents or catalysts. Moreover, the interaction of protein cages and polymers can be used to modulate the size and shape of some viral capsids to generate structures that do not occur with native viruses. Another possibility is to use the interior of polymer cages as a confined reaction space for polymerization reactions such as atom transfer radical polymerization or rhodium-catalysed polymerization of phenylacetylene. The protein nanoreactors facilitate a higher degree of control over polymer synthesis. This review will summarize the hybrid structures that have been synthesized by polymerizing from protein cage-bound initiators, by conjugating polymers to protein cages, by embedding protein cages into bulk polymeric materials, by forming two- and three-dimensional crystals of protein cages and dendrimers, by adsorbing proteins to the surface of materials, by layer-by-layer deposition of proteins and polyelectrolytes and by encapsulating polymers into protein cages. The application of these hybrid materials in the biomedical context or as tools and building blocks for bionanotechnology, biosensing, memory devices and the synthesis of materials will be highlighted. The review aims to showcase recent developments in this field and to suggest possible future directions and opportunities for the symbiosis of protein cages and polymers.

Lordosis restoration after anterior longitudinal ligament release and placement of lateral hyperlordotic interbody cages during the minimally invasive lateral transpsoas approach: a radiographic study in cadavers.

PubMed

Uribe, Juan S; Smith, Donald A; Dakwar, Elias; Baaj, Ali A; Mundis, Gregory M; Turner, Alexander W L; Cornwall, G Bryan; Akbarnia, Behrooz A

2012-11-01

In the surgical treatment of spinal deformities, the importance of restoring lumbar lordosis is well recognized. Smith-Petersen osteotomies (SPOs) yield approximately 10° of lordosis per level, whereas pedicle subtraction osteotomies result in as much as 30° increased lumbar lordosis. Recently, selective release of the anterior longitudinal ligament (ALL) and placement of lordotic interbody grafts using the minimally invasive lateral retroperitoneal transpsoas approach (XLIF) has been performed as an attempt to increase lumbar lordosis while avoiding the morbidity of osteotomy. The objective of the present study was to measure the effect of the selective release of the ALL and varying degrees of lordotic implants placed using the XLIF approach on segmental lumbar lordosis in cadaveric specimens between L-1 and L-5. Nine adult fresh-frozen cadaveric specimens were placed in the lateral decubitus position. Lateral radiographs were obtained at baseline and after 4 interventions at each level as follows: 1) placement of a standard 10° lordotic cage, 2) ALL release and placement of a 10° lordotic cage, 3) ALL release and placement of a 20° lordotic cage, and 4) ALL release and placement of a 30° lordotic cage. All four cages were implanted sequentially at each interbody level between L-1 and L-5. Before and after each intervention, segmental lumbar lordosis was measured in all specimens at each interbody level between L-1 and L-5 using the Cobb method on lateral radiography. The mean baseline segmental lordotic angles at L1-2, L2-3, L3-4, and L4-5 were -3.8°, 3.8°, 7.8°, and 22.6°, respectively. The mean lumbar lordosis was 29.4°. Compared with baseline, the mean postimplantation increase in segmental lordosis in all levels combined was 0.9° in Intervention 1 (10° cage without ALL release); 4.1° in Intervention 2 (ALL release with 10° cage); 9.5° in Intervention 3 (ALL release with 20° cage); and 11.6° in Intervention 4 (ALL release with 30° cage). Foraminal height in the same sequence of conditions increased by 6.3%, 4.6%, 8.8% and 10.4%, respectively, while central disc height increased by 16.1%, 22.3%, 52.0% and 66.7%, respectively. Following ALL release and placement of lordotic cages at all 4 lumbar levels, the average global lumbar lordosis increase from preoperative lordosis was 3.2° using 10° cages, 12.0° using 20° cages, and 20.3° using 30° cages. Global lumbar lordosis with the cages at 4 levels exhibited a negative correlation with preoperative global lordosis (10°, R = -0.756; 20°, -0.730; and 30°, R = -0.437). Combined ALL release and placement of increasingly lordotic lateral interbody cages leads to progressive gains in segmental lordosis in the lumbar spine. Mean global lumbar lordosis similarly increased with increasingly lordotic cages, although the effect with a single cage could not be evaluated. Greater global lordosis was achieved with smaller preoperative lordosis. The mean maximum increase in segmental lordosis of 11.6° followed ALL release and placement of the 30° cage.

Sol-Gel Synthesis and Crystallization of Magnesium and Calcium Rich Silicate Dust Analogs

NASA Astrophysics Data System (ADS)

Gillot, J.; Roskosz, M.; Depecker, C.; Roussel, P.; Leroux, H.

2009-03-01

A new sol-gel method optimized to synthesize amorphous and porous silicate dust analogs is proposed. The crystallization of such analogs is metastable and polyphasic. Their high reactivity is probably due to high surface/volume ratio.

Geological evolution of the Pietersburg greenstonebelt, South Africa and associated gold mineralization

NASA Technical Reports Server (NTRS)

Jones, M. G.; Dewit, M. J.

1986-01-01

The polyphase history of gold mineralization seen in the Pietersburg greenstone belt is integrated with the geochemical and tectonic evolution of greenstone belts as a whole. The four distinct regional geological settings of gold mineralization are described.

Ball to separator contact forces in angular contact ball bearings under thrust and radial loads

NASA Technical Reports Server (NTRS)

Nypan, L. J.

1977-01-01

Experimental data is reported on ball to cage contact forces in a 110 mm bore ball bearing operating at speeds to 12000 rpm under radial and thrust loads. Information is also reported on cage to inner race land contact force, cage to inner race land clearance, and cage to shaft speed ratios.

Cage drying and the application of a dry treatment (absorbent cornstarch powder) as a means to diminish Campylobacter on transport cages.

USDA-ARS?s Scientific Manuscript database

Broiler transport cages soiled with Campylobacter-positive feces have been shown to facilitate cross contamination of broilers. Campylobacter organisms are sensitive to dry stress. Allowing feces left on transport cage flooring to dry during extended periods of nonuse would be an effective method ...

Sensitivity of BN nano-cages to caffeine and nicotine molecules

NASA Astrophysics Data System (ADS)

Soltani, Alireza; Baei, Mohammad T.; Tazikeh Lemeski, E.; Shahini, Malihe

2014-12-01

Adsorption of caffeine and nicotine molecules over B12N12 and B16N16 nano-cages were investigated by using first-principles calculations to define whether BN nano-cages are applicable for filtering or sensing caffeine and nicotine molecules. The chemisorption energy of nicotine molecule on BN nano-cages is very stronger than caffeine molecule. Upon the adsorption of caffeine and nicotine molecules, the electronic properties of the BN nano-cages can be significantly changed, being too much sensitized on the caffeine and nicotine adsorptions.

Lowest-energy cage structures of medium-sized ( ZnO )n clusters with n = 15 - 24

NASA Astrophysics Data System (ADS)

Tang, Lingli; Sai, Linwei; Zhao, Jijun; Qiu, Ruifeng

2015-01-01

Fullerene-like cage structures of medium-sized ( ZnO )n clusters with n = 15 - 24 were generated by spiral algorithm and optimized using density functional theory calculations. Most of these lowest-energy cage structures contain only four-membered and six-membered rings, whereas eight-membered rings were found in the lowest-energy cages of ( ZnO )n (n = 19, 20, 23, 24). Our best cage configurations either reproduce or prevail the previously reported ones. The size-dependent electronic properties were also discussed.

Lowest-energy cage structures of medium-sized (ZnO){sub n} clusters with n = 15 − 24

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Lingli; Sai, Linwei; Zhao, Jijun, E-mail: zhaojj@dlut.edu.cn

2015-01-22

Fullerene-like cage structures of medium-sized (ZnO){sub n} clusters with n = 15 − 24 were generated by spiral algorithm and optimized using density functional theory calculations. Most of these lowest-energy cage structures contain only four-membered and six-membered rings, whereas eight-membered rings were found in the lowest-energy cages of (ZnO){sub n} (n = 19, 20, 23, 24). Our best cage configurations either reproduce or prevail the previously reported ones. The size-dependent electronic properties were also discussed.

Two zeolite-type frameworks in one metal-organic framework with Zn24 @Zn104 cube-in-sodalite architecture.

PubMed

Bu, Fei; Lin, Qipu; Zhai, Quanguo; Wang, Le; Wu, Tao; Zheng, Shou-Tian; Bu, Xianhui; Feng, Pingyun

2012-08-20

Two in one: A metal-organic framework obtained from three different inorganic building blocks (tetrameric Zn(4) O, trimeric Zn(3) OH, and monomeric Zn) posseses a nested cage-in-cage and framework-in-framework architecture. 24 Zn(4) O tetramers and eight Zn monomers form a sodalite cage into which a cubic cage made from eight Zn(3) (OH) trimers is nestled. Eight monomeric Zn(2+) centers interconnect these two cages. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

'Snorkel' lice barrier technology reduced two co- occurring parasites, the salmon louse (Lepeophtheirus salmonis) and the amoebic gill disease causing agent (Neoparamoeba perurans), in commercial salmon sea-cages.

PubMed

Wright, D W; Stien, L H; Dempster, T; Vågseth, T; Nola, V; Fosseidengen, J-E; Oppedal, F

2017-05-01

Diverse chemical-free parasite controls are gaining status in Atlantic salmon sea-cage farming. Yet, the intricacies of their use at commercial scale, including effects on co-occurring parasites, are seldom reported. A new salmon lice prevention method involves installing a deep net roof and 'snorkel' lice barrier in cages to shelter salmon from free-living infective larvae which concentrate at shallow depths, and allows salmon to jump and re- inflate their buoyancy-regulating swim bladder by swallowing air. We document use of snorkel cages (10m deep barrier) in commercial farms, where their effects on salmon lice levels, amoebic gill disease (AGD)-related gill scores, the cage environment, fish welfare and farm management practices were compared to standard cages. During an autumn-winter study involving only snorkel cages, high AGD-related gill scores were observed to decline when freshwater was pumped into snorkels, creating a freshwater surface layer for salmon to enter for self-treatment. In a spring-summer study incorporating snorkel and standard cages, snorkel cages were found to reduce new lice infestations by 84%. The deployment of snorkels and intermittent oxygen depletion detected within them in the spring-summer study did not alter fish welfare parameters. Overall, the results suggest snorkel technology has a place in the toolkit of commercial salmon sea-cage farmers co-managing salmon lice and amoebic gill disease outbreaks - two principal parasite issues facing the industry. Copyright © 2017 Elsevier B.V. All rights reserved.

Finite element analysis of lordosis restoration with anterior longitudinal ligament release and lateral hyperlordotic cage placement.

PubMed

Uribe, Juan S; Harris, Jeffrey E; Beckman, J M; Turner, Alexander W L; Mundis, Gregory M; Akbarnia, Behrooz A

2015-04-01

Restoring sagittal alignment is an important factor in the treatment of spinal deformities. Recent investigations have determined that releasing the anterior longitudinal ligament (ALL) and placing hyperlordotic cages can increase lordosis, while minimizing need for 3 column osteotomies. The influences of parameters such as cage height and angle have not been determined. Finite element analysis was employed to assess the extent of lordosis achievable after placement of different sized lordotic cages. A 3-dimensional model of a L3-4 segment was used. Disc distraction was simulated by inserting interbody cages mid-body in the disc space. Analyses were performed in the following conditions: (1) intact, (2) ALL release, (3) ALL release + facetectomy, and (4) ALL release + posterior column osteotomy. Changes in segmental lordosis, disc height, foraminal height, and foraminal area were measured. After ALL resection and insertion of hyperlordotic cages, lordosis was increased in all cases. The lordosis achieved by the shorter cages was less due to posterior disc height maintained by the facet joints. A facetectomy increased segmental lordosis, but led to contact between the spinous processes. For some configurations, a posterior column osteotomy was required if the end goal was to match cage angle to intradiscal angle. Increased segmental lumbar lordosis is achievable with hyperlordotic cages after ALL resection. Increased cage height tended to increase the amount of lordosis achieved, although in some cases additional posterior bone resection was required to maximize lordosis. Further studies are needed to evaluate the impact on regional lumbar lordosis.

Caging, but not air deprivation, slows tadpole growth and development in the amphibian Xenopus laevis.

PubMed

Rose, Christopher S

2014-08-01

Xenopus laevis tadpoles raised in submerged cages in normoxic water develop more slowly than tadpoles raised with access to air. This study distinguishes between the effects of being caged and being deprived access to air on development and growth. Tadpoles were raised in high and low density control tanks and in cages in the same tank that were either completely submerged or with the top exposed to air. Experiments were repeated with the cages in different positions relative to the air stones and with and without the water flow from air stones supplemented with a pump. Whereas caging tadpoles has a large effect on their development and growth, additionally depriving them of air has a small effect and this effect can be removed by optimizing water flow through the cage. The effect of caging, though significant in this study, is small compared to the variation in growth and developmental rates that is commonly encountered within and among controls in lab studies. Caging effects can also be diminished by optimizing rearing conditions and/or having exceptionally vigorous tadpoles. The effects of air deprivation and caging thus pose less of a problem for experimenting on air-deprived (AD) and air-restored Xenopus tadpoles than their inherent variability in growth and developmental rates and their susceptibility to growth and developmental arrest. Further, the effect of air deprivation in this air-breathing amphibian does not pose a conflict with evolutionary hypotheses for lung loss involving lengthening of the larval period and delay in the onset of air breathing. © 2014 Wiley Periodicals, Inc.

Caging and Photoactivation in Single-Molecule Förster Resonance Energy Transfer Experiments

PubMed Central

2017-01-01

Caged organic fluorophores are established tools for localization-based super-resolution imaging. Their use relies on reversible deactivation of standard organic fluorophores by chemical reduction or commercially available caged dyes with ON switching of the fluorescent signal by ultraviolet (UV) light. Here, we establish caging of cyanine fluorophores and caged rhodamine dyes, i.e., chemical deactivation of fluorescence, for single-molecule Förster resonance energy transfer (smFRET) experiments with freely diffusing molecules. They allow temporal separation and sorting of multiple intramolecular donor–acceptor pairs during solution-based smFRET. We use this “caged FRET” methodology for the study of complex biochemical species such as multisubunit proteins or nucleic acids containing more than two fluorescent labels. Proof-of-principle experiments and a characterization of the uncaging process in the confocal volume are presented. These reveal that chemical caging and UV reactivation allow temporal uncoupling of convoluted fluorescence signals from, e.g., multiple spectrally similar donor or acceptor molecules on nucleic acids. We also use caging without UV reactivation to remove unwanted overlabeled species in experiments with the homotrimeric membrane transporter BetP. We finally outline further possible applications of the caged FRET methodology, such as the study of weak biochemical interactions, which are otherwise impossible with diffusion-based smFRET techniques because of the required low concentrations of fluorescently labeled biomolecules. PMID:28362086

A New Vertebral Body Replacement Strategy Using Expandable Polymeric Cages

PubMed Central

Liu, Xifeng; Paulsen, Alex; Giambini, Hugo; Guo, Ji; Miller, A. Lee; Lin, Po-Chun; Yaszemski, Michael J.

2017-01-01

We have developed a novel polymeric expandable cage that can be delivered via a posterior-only surgical approach for the treatment of noncontained vertebral defects. This approach is less invasive than an anterior-only or combined approach and much more cost-effective than currently used expandable metal cages. The polymeric expandable cage is composed of oligo poly(ethylene glycol) fumarate (OPF), a hydrogel that has been previously shown to have excellent nerve and bone tissue biocompatibility. OPF hydrogel cages can expand to twice their original diameter and length within a surgical time frame following hydration. Modulation of parameters such as polymeric network crosslink density or the introduction of charge to the network allowed for precise expansion kinetics. To meet specific requirements due to size variations in patient vertebral bodies, we fabricated a series of molds with varied diameters and explored the expansion kinetics of the OPF cages. Results showed a stable expansion ratio of approximately twofold to the original size within 20 min, regardless of the absolute value of the cage size. Following implantation of a dried OPF cage into a noncontained vertebral defect and its in situ expansion with normal saline, other augmentation biomaterials, such as poly(propylene fumarate) (PPF), can be injected to the lumen of the OPF cage and allowed to crosslink in situ. The OPF/PPF composite scaffold can provide the necessary rigidity and stability to the augmented spine. PMID:27835935

Effect of lipopolysaccharide on sickness behaviour in hens kept in cage and free range environments.

PubMed

Gregory, N G; Payne, S R; Devine, C D; Cook, C J

2009-08-01

The aim of this study was to assess whether environmental enrichment and environmental conditions can influence the expression of sickness behaviour. The behaviour in response to injection of lipopolysaccharide or saline was examined in a total of 96 62-weeks old hatchmate hens kept in a free range or cage environment. There were eight experimental treatments, each with 12 birds. Half the birds were sourced from a commercial cage layer unit (C/-) and half from a commercial free range unit (FR/-). After intraperitoneal injection with either lipopolysaccharide or saline (as a control), the hens were placed in either a cage (-/C) or free range (-/FR) environment. Lipopolysaccharide caused greater suppression of activity in free range (FR/FR) than in caged hens, including less walking (53% reduction), roosting (-86%) and preening (-60%) (p<0.05). Those responses were not observed in caged birds released into free range, nor in free range birds introduced to cages, suggesting that both the presence of and the familiarity with an environment affected sickness behaviour patterns. Increased sleeping was the most consistent response (+147%; p<0.001), and it was least influenced by environment. It was concluded that free range layer hens can express a greater range of sickness behaviours than caged hens, and this may make it more difficult to recognise disease expression in the caged environment.

78 FR 32374 - Magnuson-Stevens Act Provisions; General Provisions for Domestic Fisheries; Application for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-30

...) 281-9135. FOR FURTHER INFORMATION CONTACT: Jason Berthiaume, Fishery Management Specialist, 978-281...-standard cages and 32-bu (1,703.68 L) cage tags. The traditional cages do not fit on smaller day-boats and... system, with each tag representing 32 bu (1,703.68 L) of allocation, or one cage. In addition to managing...

Eggshell bacterial levels of non-washed and washed eggs from caged and cage-free hens

USDA-ARS?s Scientific Manuscript database

The bacteria levels of non-washed and washed eggs obtained from caged and cage-free laying hens housed on either all shavings or all wire slat floors were determined. On eight sample days (from 22 to 52 weeks at 4 week intervals), 20 eggs were collected from each pen (n=120/sample day). Ten eggs p...

Ball to separator contact forces in angular contact ball bearings under thrust and radial loads

NASA Technical Reports Server (NTRS)

Nypan, L. J.

1978-01-01

Experimental data are reported on ball to cage contact forces in a 110 mm bore ball bearing operating at speeds to 12,000 rpm under radial and thrust loads. Information is also reported on cage to inner race land contact force, cage to inner race land clearance, and cage to shaft speed ratios.

Hen genetic strain and extended cold storage implications on physical egg quality from cage-free aviary housing system

USDA-ARS?s Scientific Manuscript database

In the US there is a sudden increase in the need for cage-free eggs in retail and food manufacturing sectors. As the US industry adapts existing and builds new cage-free housing structures, there is a need to understand the impact of cage-free systems and the corresponding management on egg quality...

Individually ventilated cages cause chronic low-grade hypoxia impacting mice hematologically and behaviorally

PubMed Central

York, Jason M.; McDaniel, Allison W.; Blevins, Neil A.; Guillet, Riley R.; Allison, Sarah O.; Cengel, Keith A.; Freund, Gregory G.

2012-01-01

Use of individually ventilated caging (IVC) systems for mouse-based laboratory investigation has dramatically increased. We found that without mice present, intra-cage oxygen concentration was comparable (21%) between IVC housing and ambient environment caging (AEC) that used wire top lids. However, when mice were housed 4-to-a-cage for 1 week, intra-cage oxygen dropped to 20.5% in IVC housing as compared to 21% for AEC housing. IVC intra-cage humidity was also elevated relative to AEC housing. Mice raised in IVC housing as compared to mice raised in AEC housing had higher RBC mass, hematocrit and hemoglobin concentrations. They also had elevated platelet counts but lower white blood cell counts. IVC mice relative to AEC mice had increased saccharin preference and increased fluid consumption but similar locomotion, food intake, social exploration and novel object recognition when tested in an AEC environment. Taken together, these data indicate that ventilated caging systems can have a 0.5% reduction from ambient oxygen concentration that is coupled to mouse red blood cell indices indicative of chronic exposure to a hypoxia. Importantly, IVC housing can impact behavioral testing for depressive-like behavior. PMID:22561683

Diversification of Protein Cage Structure Using Circularly Permuted Subunits.

PubMed

Azuma, Yusuke; Herger, Michael; Hilvert, Donald

2018-01-17

Self-assembling protein cages are useful as nanoscale molecular containers for diverse applications in biotechnology and medicine. To expand the utility of such systems, there is considerable interest in customizing the structures of natural cage-forming proteins and designing new ones. Here we report that a circularly permuted variant of lumazine synthase, a cage-forming enzyme from Aquifex aeolicus (AaLS) affords versatile building blocks for the construction of nanocompartments that can be easily produced, tailored, and diversified. The topologically altered protein, cpAaLS, self-assembles into spherical and tubular cage structures with morphologies that can be controlled by the length of the linker connecting the native termini. Moreover, cpAaLS proteins integrate into wild-type and other engineered AaLS assemblies by coproduction in Escherichia coli to form patchwork cages. This coassembly strategy enables encapsulation of guest proteins in the lumen, modification of the exterior through genetic fusion, and tuning of the size and electrostatics of the compartments. This addition to the family of AaLS cages broadens the scope of this system for further applications and highlights the utility of circular permutation as a potentially general strategy for tailoring the properties of cage-forming proteins.

CAGEd-oPOSSUM: motif enrichment analysis from CAGE-derived TSSs.

PubMed

Arenillas, David J; Forrest, Alistair R R; Kawaji, Hideya; Lassmann, Timo; Wasserman, Wyeth W; Mathelier, Anthony

2016-09-15

With the emergence of large-scale Cap Analysis of Gene Expression (CAGE) datasets from individual labs and the FANTOM consortium, one can now analyze the cis-regulatory regions associated with gene transcription at an unprecedented level of refinement. By coupling transcription factor binding site (TFBS) enrichment analysis with CAGE-derived genomic regions, CAGEd-oPOSSUM can identify TFs that act as key regulators of genes involved in specific mammalian cell and tissue types. The webtool allows for the analysis of CAGE-derived transcription start sites (TSSs) either provided by the user or selected from ∼1300 mammalian samples from the FANTOM5 project with pre-computed TFBS predicted with JASPAR TF binding profiles. The tool helps power insights into the regulation of genes through the study of the specific usage of TSSs within specific cell types and/or under specific conditions. The CAGEd-oPOSUM web tool is implemented in Perl, MySQL and Apache and is available at http://cagedop.cmmt.ubc.ca/CAGEd_oPOSSUM CONTACTS: anthony.mathelier@ncmm.uio.no or wyeth@cmmt.ubc.ca Supplementary data are available at Bioinformatics online. © The Author 2016. Published by Oxford University Press.

Automated home cage observations as a tool to measure the effects of wheel running on cage floor locomotion.

PubMed

de Visser, Leonie; van den Bos, Ruud; Spruijt, Berry M

2005-05-28

This paper introduces automated observations in a modular home cage system as a tool to measure the effects of wheel running on the time distribution and daily organization of cage floor locomotor activity in female C57BL/6 mice. Mice (n = 16) were placed in the home cage system for 6 consecutive days. Fifty percent of the subjects had free access to a running wheel that was integrated in the home cage. Overall activity levels in terms of duration of movement were increased by wheel running, while time spent inside a sheltering box was decreased. Wheel running affected the hourly pattern of movement during the animals' active period of the day. Mice without a running wheel, in contrast to mice with a running wheel, showed a clear differentiation between novelty-induced and baseline levels of locomotion as reflected by a decrease after the first day of introduction to the home cage. The results are discussed in the light of the use of running wheels as a tool to measure general activity and as an object for environmental enrichment. Furthermore, the possibilities of using automated home cage observations for e.g. behavioural phenotyping are discussed.

Polarization response of clathrate hydrates capsulated with guest molecules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeng, Qun; Li, Jinshan, E-mail: ljs915@263.net, E-mail: myang@scu.edu.cn; Huang, Hui

2016-05-28

Clathrate hydrates are characterized by their water cages encapsulating various guest atoms or molecules. The polarization effect of these guest-cage complexes was studied with combined density functional theory and finite-field calculations. An addition rule was noted for these systems whose total polarizability is approximately equal to the polarizability sum of the guest and the cage. However, their distributional polarizability computed with Hirshfeld partitioning scheme indicates that the guest–cage interaction has considerable influence on their polarization response. The polarization of encapsulated guest is reduced while the polarization of water cage is enhanced. The counteraction of these two opposite effects leads tomore » the almost unchanged total polarizability. Further analysis reveals that the reduced polarizability of encapsulated guest results from the shielding effect of water cage against the external field and the enhanced polarizability of water cage from the enhanced bonding of hydrogen bonds among water molecules. Although the charge transfer through the hydrogen bonds is rather small in the water cage, the polarization response of clathrate hydrates is sensitive to the changes of hydrogen bonding strength. The guest encapsulation strengthens the hydrogen bonding network and leads to enhanced polarizability.« less

CAGEd-oPOSSUM: motif enrichment analysis from CAGE-derived TSSs

PubMed Central

Arenillas, David J.; Forrest, Alistair R. R.; Kawaji, Hideya; Lassmann, Timo; Wasserman, Wyeth W.; Mathelier, Anthony

2016-01-01

With the emergence of large-scale Cap Analysis of Gene Expression (CAGE) datasets from individual labs and the FANTOM consortium, one can now analyze the cis-regulatory regions associated with gene transcription at an unprecedented level of refinement. By coupling transcription factor binding site (TFBS) enrichment analysis with CAGE-derived genomic regions, CAGEd-oPOSSUM can identify TFs that act as key regulators of genes involved in specific mammalian cell and tissue types. The webtool allows for the analysis of CAGE-derived transcription start sites (TSSs) either provided by the user or selected from ∼1300 mammalian samples from the FANTOM5 project with pre-computed TFBS predicted with JASPAR TF binding profiles. The tool helps power insights into the regulation of genes through the study of the specific usage of TSSs within specific cell types and/or under specific conditions. Availability and Implementation: The CAGEd-oPOSUM web tool is implemented in Perl, MySQL and Apache and is available at http://cagedop.cmmt.ubc.ca/CAGEd_oPOSSUM. Contacts: anthony.mathelier@ncmm.uio.no or wyeth@cmmt.ubc.ca Supplementary information: Supplementary data are available at Bioinformatics online. PMID:27334471

Homogenized boundary conditions and resonance effects in Faraday cages

PubMed Central

Hewitt, I. J.

2016-01-01

We present a mathematical study of two-dimensional electrostatic and electromagnetic shielding by a cage of conducting wires (the so-called ‘Faraday cage effect’). Taking the limit as the number of wires in the cage tends to infinity, we use the asymptotic method of multiple scales to derive continuum models for the shielding, involving homogenized boundary conditions on an effective cage boundary. We show how the resulting models depend on key cage parameters such as the size and shape of the wires, and, in the electromagnetic case, on the frequency and polarization of the incident field. In the electromagnetic case, there are resonance effects, whereby at frequencies close to the natural frequencies of the equivalent solid shell, the presence of the cage actually amplifies the incident field, rather than shielding it. By appropriately modifying the continuum model, we calculate the modified resonant frequencies, and their associated peak amplitudes. We discuss applications to radiation containment in microwave ovens and acoustic scattering by perforated shells. PMID:27279775

Homogenized boundary conditions and resonance effects in Faraday cages

NASA Astrophysics Data System (ADS)

Hewett, D. P.; Hewitt, I. J.

2016-05-01

We present a mathematical study of two-dimensional electrostatic and electromagnetic shielding by a cage of conducting wires (the so-called `Faraday cage effect'). Taking the limit as the number of wires in the cage tends to infinity, we use the asymptotic method of multiple scales to derive continuum models for the shielding, involving homogenized boundary conditions on an effective cage boundary. We show how the resulting models depend on key cage parameters such as the size and shape of the wires, and, in the electromagnetic case, on the frequency and polarization of the incident field. In the electromagnetic case, there are resonance effects, whereby at frequencies close to the natural frequencies of the equivalent solid shell, the presence of the cage actually amplifies the incident field, rather than shielding it. By appropriately modifying the continuum model, we calculate the modified resonant frequencies, and their associated peak amplitudes. We discuss applications to radiation containment in microwave ovens and acoustic scattering by perforated shells.

Homogenized boundary conditions and resonance effects in Faraday cages.

PubMed

Hewett, D P; Hewitt, I J

2016-05-01

We present a mathematical study of two-dimensional electrostatic and electromagnetic shielding by a cage of conducting wires (the so-called 'Faraday cage effect'). Taking the limit as the number of wires in the cage tends to infinity, we use the asymptotic method of multiple scales to derive continuum models for the shielding, involving homogenized boundary conditions on an effective cage boundary. We show how the resulting models depend on key cage parameters such as the size and shape of the wires, and, in the electromagnetic case, on the frequency and polarization of the incident field. In the electromagnetic case, there are resonance effects, whereby at frequencies close to the natural frequencies of the equivalent solid shell, the presence of the cage actually amplifies the incident field, rather than shielding it. By appropriately modifying the continuum model, we calculate the modified resonant frequencies, and their associated peak amplitudes. We discuss applications to radiation containment in microwave ovens and acoustic scattering by perforated shells.

Mitochondria mediate septin cage assembly to promote autophagy of Shigella.

PubMed

Sirianni, Andrea; Krokowski, Sina; Lobato-Márquez, Damián; Buranyi, Stephen; Pfanzelter, Julia; Galea, Dieter; Willis, Alexandra; Culley, Siân; Henriques, Ricardo; Larrouy-Maumus, Gerald; Hollinshead, Michael; Sancho-Shimizu, Vanessa; Way, Michael; Mostowy, Serge

2016-07-01

Septins, cytoskeletal proteins with well-characterised roles in cytokinesis, form cage-like structures around cytosolic Shigella flexneri and promote their targeting to autophagosomes. However, the processes underlying septin cage assembly, and whether they influence S. flexneri proliferation, remain to be established. Using single-cell analysis, we show that the septin cages inhibit S. flexneri proliferation. To study mechanisms of septin cage assembly, we used proteomics and found mitochondrial proteins associate with septins in S. flexneri-infected cells. Strikingly, mitochondria associated with S. flexneri promote septin assembly into cages that entrap bacteria for autophagy. We demonstrate that the cytosolic GTPase dynamin-related protein 1 (Drp1) interacts with septins to enhance mitochondrial fission. To avoid autophagy, actin-polymerising Shigella fragment mitochondria to escape from septin caging. Our results demonstrate a role for mitochondria in anti-Shigella autophagy and uncover a fundamental link between septin assembly and mitochondria. © 2016 The Authors. Published under the terms of the CC BY 4.0 license.

Photo-dependent protein biosynthesis using a caged aminoacyl-tRNA.

PubMed

Akahoshi, Akiya; Doi, Yoshio; Sisido, Masahiko; Watanabe, Kazunori; Ohtsuki, Takashi

2014-12-01

Translation systems with four-base codons provide a powerful strategy for protein engineering and protein studies because they enable site-specific incorporation of non-natural amino acids into proteins. In this study, a caged aminoacyl-tRNA with a four-base anticodon was synthesized. The caged aminoacyl-tRNA contains a photocleavable nitroveratryloxycarbonyl (NVOC) group. This study showed that the caged aminoacyl-tRNA was not deacylated, did not bind to EF-Tu, and was activated by light. Photo-dependent translation of an mRNA containing the four-base codon was demonstrated using the caged aminoacyl-tRNA.

A new germfree chicken cage--characteristics and use.

PubMed

MILLER, H T; LUCKEY, T D

1962-01-01

A new germfree chicken cage for rearing chicks up to 3 or 4 weeks of age has been designed and is in use at the University of Missouri. The cage and the accessory parts, the small magnet and hinged door, the "Bactytector," the built-in air filter assembly, and the glass top with connecting air outlet filter have been described in detail. The complete operating procedure for sterilizing the cage and diet and the method of adding sterile embryonated eggs have been outlined. Data on the effectiveness of the cage as a physical barrier to microbes have been presented.

Establishment of a medium-scale mosquito facility: tests on mass production cages for Aedes albopictus (Diptera: Culicidae).

PubMed

Zhang, Dongjing; Li, Yongjun; Sun, Qiang; Zheng, Xiaoying; Gilles, Jeremie R L; Yamada, Hanano; Wu, Zhongdao; Xi, Zhiyong; Wu, Yu

2018-03-19

Mass egg production is an important component of Aedes albopictus mosquito control programs, such as the sterile insect technique and incompatible insect technique, which requires the releases of large number of sterile males. Developing standard operating procedures and optimized cages for adult maintenance of Ae. albopictus can improve the mass rearing efficiency. Three different sex ratios of females to males with a total number of 4,000 mosquitoes were tested by evaluating the insemination rate, egg production (total number of eggs per cage), female fecundity and egg hatch rate in small cage (30 × 30 × 30 cm). Blood meals with adenosine triphosphate (ATP, 0.05 g/ml), cage structures (Big cage A: 90 × 30 × 30 cm; Big cage B: 90 × 30 × 50 cm or 90 × 50 × 30 cm) and rearing densities (12,000, 16,000 and 20,000 mosquitoes, corresponding to 0.9 cm 2 /mosquito, 0.675 cm 2 /mosquito and 0.54 cm 2 /mosquito, respectively) were also tested and evaluated on the basis of egg production, female fecundity and egg hatch rate. An adult rearing unit holding 15 of Big cage A with optimal egg production was designed to produce 10 million eggs per rearing cycle in a 1.8 m 2 space. Female to male ratios at 3:1 in small cages resulted in higher egg production but did not affect insemination rate, female fecundity and egg hatch rate. A concentration of 0.05 g/ml of ATP added to blood meals improved the blood-feeding frequency and thus increased the overall egg production per cage. Cage structures affected the egg production per cage, but not egg hatch rate. A medium rearing density at 0.675 cm 2 /mosquito (16,000 mosquitoes) resulted in higher egg production compared to both low and high densities. An adult rearing unit for Ae. albopictus on the basis of Big cage A has been developed with the capacity of producing 10 million eggs within 15 days. Our results have indicated that the adult rearing methods and adult maintenance unit are recommended for Ae. albopictus mass rearing in support of the establishment of a medium-sized mosquito factory.

Interbody fusion cage design using integrated global layout and local microstructure topology optimization.

PubMed

Lin, Chia-Ying; Hsiao, Chun-Ching; Chen, Po-Quan; Hollister, Scott J

2004-08-15

An approach combining global layout and local microstructure topology optimization was used to create a new interbody fusion cage design that concurrently enhanced stability, biofactor delivery, and mechanical tissue stimulation for improved arthrodesis. To develop a new interbody fusion cage design by topology optimization with porous internal architecture. To compare the performance of this new design to conventional threaded cage designs regarding early stability and long-term stress shielding effects on ingrown bone. Conventional interbody cage designs mainly fall into categories of cylindrical or rectangular shell shapes. The designs contribute to rigid stability and maintain disc height for successful arthrodesis but may also suffer mechanically mediated failures of dislocation or subsidence, as well as the possibility of bone resorption. The new optimization approach created a cage having designed microstructure that achieved desired mechanical performance while providing interconnected channels for biofactor delivery. The topology optimization algorithm determines the material layout under desirable volume fraction (50%) and displacement constraints favorable to bone formation. A local microstructural topology optimization method was used to generate periodic microstructures for porous isotropic materials. Final topology was generated by the integration of the two-scaled structures according to segmented regions and the corresponding material density. Image-base finite element analysis was used to compare the mechanical performance of the topology-optimized cage and conventional threaded cage. The final design can be fabricated by a variety of Solid Free-Form systems directly from the image output. The new design exhibited a narrower, more uniform displacement range than the threaded cage design and lower stress at the cage-vertebra interface, suggesting a reduced risk of subsidence. Strain energy density analysis also indicated that a higher portion of total strain energy density was transferred into the new bone region inside the new designed cage, indicating a reduced risk of stress shielding. The new design approach using integrated topology optimization demonstrated comparable or better stability by limited displacement and reduced localized deformation related to the risk of subsidence. Less shielding of newly formed bone was predicted inside the new designed cage. Using the present approach, it is also possible to tailor cage design for specific materials, either titanium or polymer, that can attain the desired balance between stability, reduced stress shielding, and porosity for biofactor delivery.

Polyphasic taxonomic characterisation of a novel strain as Pararhizobium haloflavum sp. nov., isolated from soil samples near a sewage treatment tank.

PubMed

Shen, Xia; Li, Yu; Zhao, Zhe; Han, Yi-Fan; Zhang, Wen-Wu; Yu, Xiao-Yun; Zhang, Chong-Ya; Sun, Cong; Wu, Min

2018-04-01

A Gram-stain negative, aerobic, motile and ovoid- to rod-shaped bacteria strain, designated XC0140 T , was isolated from soil samples near the sewage treatment tank of a chemical factory in Zhejiang Province, China, and subjected to polyphasic taxonomic investigation. Strain XC0140 T grew at 10-37 °C and pH 6.0-9.0 (optimum, 35 °C and pH 7.5) and with 0-17% (w/v) NaCl (optimum, 1%). According to phylogenetic analysis based on 16S rRNA gene sequences, strain XC0140 T was assigned to the genus Pararhizobium with high 16S rRNA gene sequence similarity of 95.97% to "Pararhizobium helanshanense CCNWQTX14 T" , followed by Pararhizobium sphaerophysae CCNWGS0238 T (95.95%). Chemotaxonomic analysis showed that strain XC0140 T contains ubiquinone-10 as the predominant respiratory quinone and possessed summed feature 8 (comprising C 18: 1 ω7c and/or ω6c), 11-methyl C 18:1 ω7c, C 18: 0 and C 16: 0 as predominant forms of fatty acids. The polar lipids of strain XC0140 T consisted of seven phospholipids (PL), two aminolipids (AL), one glycolipid (GL) and three unidentified lipids (L1, L2 and L3). The DNA G+C content was 62.7 mol%. Based on the polyphasic taxonomic characterization, strain XC0140 T is considered to represent a novel species of the genus Pararhizobium, for which the name Pararhizobium haloflavum sp. nov. is proposed. (type strain XC0140 T  = MCCC 1K03228 T  = KCTC 52582 T ).

Point-contact tunneling in monophasic and polyphasic Y-Ba-Cu-O samples: Experiment and model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gonnelli, R.S.; Andreone, D.; Lacquaniti, V.

1989-02-01

Tunneling experiments using large-area point-contact structures have been performed on several monophasic polycrystalline Ba/sub 2/Cu/sub 3/O/sub 7-//sub delta/ samples and on polyphasic samples containing, mixed with the previous superconducting phase, also about 11% of the so-called green phase (BaY/sub 2/CuO/sub 5/). Both niobium and Y-Ba-Cu-O tips were used as counterelectrodes and measurements were made at 4.2 and 77 K. Results obtained at different experimental conditions show great reproducibility indicating the presence of the gap voltage at about 20 mV in the dynamic resistance curves. A phenomenological model was then developed to interpret in a quantitative way our data by meansmore » of a decomposition of the experimental conductance into a background component and a superconducting-tunneling component. The former results essentially in a parabolic contribution versus the bias voltage typical of a tunneling between normallike junction electrodes while the latter component is smeared out in voltage by a large amount of broadening. Using the model in a least-squares fit of the experimental data of Nb/Y-Ba-Cu-O junctions, values V/sub G/ = 21.3 +- 0.8 mV and V/sub G/ = 22.0 +- 0.6 mV for the voltage gaps at 4.2 K of monophasic and polyphasic materials, respectively, have been determined. These results have been well confirmed by measurements on Y-Ba-Cu-O/Y-Ba-Cu-O junctions while, at 77 K, there are no indications of a superconducting tunneling. We obtained also the parameters of the background conductance, which indicates the presence of a nonsuperconducting layer at the surface of the material.« less

Phanerozoic polyphase orogenies recorded in the northeastern Okcheon Belt, Korea from SHRIMP U-Pb detrital zircon and K-Ar illite geochronologies

NASA Astrophysics Data System (ADS)

Jang, Yirang; Kwon, Sanghoon; Song, Yungoo; Kim, Sung Won; Kwon, Yi Kyun; Yi, Keewook

2018-05-01

We present the SHRIMP U-Pb detrital zircon and K-Ar illite 1Md/1M and 2M1 ages, suggesting new insight into the Phanerozoic polyphase orogenies preserved in the northeastern Okcheon Belt, Korea since the initial basin formation during Neoproterozoic rifting through several successive contractional orogens. The U-Pb detrital zircon ages from the Early Paleozoic strata of the Taebaeksan Zone suggest a Cambrian maximum deposition age, and are supported by trilobite and conodont biostratigraphy. Although the age spectra from two sedimentary groups, the Yeongwol and Taebaek Groups, show similar continuous distributions from the Late Paleoproterozoic to Early Paleozoic ages, a Grenville-age hiatus (1.3-0.9 Ga) in the continuous stratigraphic sequence from the Taebaek Group suggests the existence of different peripheral clastic sources along rifted continental margin(s). In addition, we present the K-Ar illite 1Md/1M ages of the fault gouges, which confirm fault formation/reactivation during the Late Cretaceous to Early Paleogene (ca. 82-62 Ma) and the Early Miocene (ca. 20-18 Ma). The 2M1 illite ages, at least those younger than the host rock ages, provide episodes of deformation, metamorphism and hydrothermal effects related to the tectonic events during the Devonian (ca.410 Ma) and Permo-Triassic (ca. 285-240 Ma). These results indicate that the northeastern Okcheon Belt experienced polyphase orogenic events, namely the Okcheon (Middle Paleozoic), Songrim (Late Paleozoic to Early Mesozoic), Daebo (Middle Mesozoic) and Bulguksa (Late Mesozoic to Early Cenozoic) Orogenies, reflecting the Phanerozoic tectonic evolution of the Korean Peninsula along the East Asian continental margin.

Room environment influence on eggshell bacterial levels of non-washed and washed eggs from caged and cage-free laying hens

USDA-ARS?s Scientific Manuscript database

The bacteria levels of non-washed and washed eggs obtained from caged and cage-free hens housed in either wire slats or shaving-covered pens were determined. On eight days (from 22 to 52 wk), 20 eggs were collected from each pen. Ten eggs/pen were washed with a commercial egg washing solution, whi...

Study of rolling element dynamic interactions with separators and raceway paths: Roller to separator contact forces and cage to shaft speed ratios in roller bearings

NASA Technical Reports Server (NTRS)

Nypan, L. J.

1978-01-01

Cage to roller force measurements, cage to shaft forces, and cage to shaft speed ratios are reported for 115 and 118mm bore roller bearings operating at speeds of 4,000, 8,000, and 12,000 rpm under loads ranging from 360 to 6670 N (80 to 1500 lb).

Furnished Cage System and Hen Well-Being: Comparative Effects of Furnished and Battery Cages on Egg Production and Physiological Parameters of White Leghorn Hens

USDA-ARS?s Scientific Manuscript database

Laboratory animal well-being can be improved by housing the animals in a species-special “natural” or “near to natural” environment. This study was to examine if housing environment, furnished cages vs. battery cages, causes a similar impact on well-being in laying hens. One hundred seventy-two, on...

Anterior cervical corpectomy: review and comparison of results using titanium mesh cages and carbon fibre reinforced polymer cages.

PubMed

Kabir, Syed M R; Alabi, J; Rezajooi, Kia; Casey, Adrian T H

2010-10-01

Different types of cages have recently become available for reconstruction following anterior cervical corpectomy. We review the results using titanium mesh cages (TMC) and stackable CFRP (carbon fibre reinforced polymer) cages. Forty-two patients who underwent anterior cervical corpectomy between November 2001 and September 2008 were retrospectively reviewed. Pathologies included cervical spondylotic myelopathy (CSM), cervical radiculopathy, OPLL (ossified posterior longitudinal ligament), metastasis/primary bone tumour, rheumatoid arthritis and deformity correction. All patients were evaluated clinically and radiologically. Outcome was assessed on the basis of the Odom's criteria, neck disability index (NDI) and myelopathy disability index (MDI). Mean age was 60 years and mean follow-up was 1½ years. Majority of the patients had single-level corpectomy. Twenty-three patients had TMC cages while 19 patients had CFRP cages. The mean subsidence noted with TMC cage was 1.91 mm, while with the stackable CFRP cage it was 0.5 mm. This difference was statistically significant (p < 0.05). However, there was no statistically significant correlation noted between subsidence and clinical outcome (p > 0.05) or between subsidence and post-operative sagittal alignment (p > 0.05) in either of the groups. Three patients had significant subsidence (> 3 mm), one of whom was symptomatic. There were no hardware-related complications. On the basis of the Odom's criterion, 9 patients (21.4%) had an excellent outcome, 14 patients (33.3%) had a good outcome, 9 patients (21.4%) had a fair outcome and 5 patients (11.9%) had a poor outcome, i.e. symptoms and signs unchanged or exacerbated. Mean post-operative NDI was 26.27% and mean post-operative MDI was 19.31%. Fusion was noted in all 42 cases. Both TMC and stackable CFRP cages provide solid anterior column reconstruction with good outcome following anterior cervical corpectomy. However, more subsidence is noted with TMC cages though this might not significantly alter the clinical outcome unless the subsidence is significant (>3 mm).

PMMA versus titanium cage after anterior cervical discectomy - a prospective randomized trial.

PubMed

Schröder, J; Grosse-Dresselhaus, F; Schul, C; Wassmann, H

2007-02-01

Nonautologous interbody fusion materials are utilised in increasing numbers after anterior cervical disc surgery to overcome the problem of donor site morbidity of autologous bone grafts. This study investigates the performance of two nonautologous materials, the bone cement Polymethylmethacrylate (PMMA) and titanium cages. This prospective randomised trial, with assessment of the results by an independent observer, evaluates whether a Polymethylmethacrylate (PMMA) spacer or a titanium cage provides a better fusion rate around the implant and a better clinical outcome. Between 2000 and 2002, 115 patients with monoradicular cervical nerve root compression syndrome caused by soft cervical disc herniation were eligible for this study. Myelopathy, excessive osteophyte formation, and adjacent level degeneration were exclusion criteria. A block-restricted randomisation was applied. The 2-year clinical outcome served as the primary endpoint of the study. Clinical outcome was assessed according to the Odom scale by an independent observer at the follow-up examination. Preoperative, postoperative, and follow-up radiographs were taken. The study was completed by 107 patients (53 with PMMA and 54 with titanium cage). No significant difference between the two groups could be established with respect to the clinical outcome. In each group, 26 patients scored excellent. Good results were found in 19 PMMA patients and 16 titanium cage patients; satisfactory results were found in 8 PMMA patients and 9 titanium cage patients; bad results were found in 3 titanium cage patients. In 47 titanium cage cases (87%), fusion occurred radiologically as bony bridging around the implant. The fusion rate was significantly lower (p=0.011) in the PMMA group, with 35 cases (66%) united at follow-up. The radiological result of the titanium cage is superior to that of PMMA with respect to the fusion rate. Although the titanium cage achieves a better fusion rate, there is no difference between titanium cages and PMMA with respect to the clinical outcome.

Reinventing the wheel: comparison of two wheel cage styles for assessing mouse voluntary running activity.

PubMed

Seward, T; Harfmann, B D; Esser, K A; Schroder, E A

2018-04-01

Voluntary wheel cage assessment of mouse activity is commonly employed in exercise and behavioral research. Currently, no standardization for wheel cages exists resulting in an inability to compare results among data from different laboratories. The purpose of this study was to determine whether the distance run or average speed data differ depending on the use of two commonly used commercially available wheel cage systems. Two different wheel cages with structurally similar but functionally different wheels (electromechanical switch vs. magnetic switch) were compared side-by-side to measure wheel running data differences. Other variables, including enrichment and cage location, were also tested to assess potential impacts on the running wheel data. We found that cages with the electromechanical switch had greater inherent wheel resistance and consistently led to greater running distance per day and higher average running speed. Mice rapidly, within 1-2 days, adapted their running behavior to the type of experimental switch used, suggesting these running differences are more behavioral than due to intrinsic musculoskeletal, cardiovascular, or metabolic limits. The presence of enrichment or location of the cage had no detectable impact on voluntary wheel running. These results demonstrate that mice run differing amounts depending on the type of cage and switch mechanism used and thus investigators need to report wheel cage type/wheel resistance and use caution when interpreting distance/speed run across studies. NEW & NOTEWORTHY The results of this study highlight that mice will run different distances per day and average speed based on the inherent resistance present in the switch mechanism used to record data. Rapid changes in running behavior for the same mouse in the different cages demonstrate that a strong behavioral factor contributes to classic exercise outcomes in mice. Caution needs to be taken when interpreting mouse voluntary wheel running activity to include potential behavioral input and physiological parameters.

Persistence of fecal shedding of Salmonella Enteritidis by experimentally infected laying hens housed in conventional or enriched cages.

PubMed

Gast, Richard K; Guraya, Rupa; Jones, Deana R; Anderson, Kenneth E

2015-07-01

Salmonella Enteritidis can be deposited inside eggs laid by infected hens, so the prevalence of this pathogen in commercial egg-producing flocks is an important risk factor for human illness. Opportunities for the introduction, transmission, and persistence of salmonellae in poultry are potentially influenced by flock housing and management systems. Animal welfare concerns have spurred the development of alternatives to traditional cage-based housing. However, the consequences of poultry housing systems for food safety have not been fully resolved by prior research. The present study assessed the effects of two different housing systems (conventional cages and colony cages enriched with perching and nesting areas) on the persistence of fecal shedding of Salmonella Enteritidis by groups of experimentally infected laying hens. In each of two trials, 136 hens were distributed among cages of both housing systems and orally inoculated with doses of 10(8) cfu of Salmonella Enteritidis (phage type 13a in one trial and phage type 4 in the other). At weekly intervals, samples of voided feces were collected from beneath each cage and cultured to detect Salmonella Enteritidis. Fecal shedding of Salmonella Enteritidis was detected for up to 8 wk post-inoculation by hens housed in enriched colony cages and 10 wk by hens housed in conventional cages. For both trials combined, the frequency of positive fecal cultures was significantly (P < 0.05) greater for conventional cages than for enriched colony cages at 1 wk (84.7 vs. 71.5%), 2 wk (54.2 vs. 31.3%), 3 wk (21.5 vs. 7.6%), and 4 wk (9.7 vs. 2.8%) post-inoculation. These results demonstrate that the susceptibility of hens to intestinal colonization by Salmonella Enteritidis can differ between conventional and enriched cage-based production systems, although this effect does not necessarily translate into a corresponding difference in the longer-term persistence of fecal shedding. © 2015 Poultry Science Association Inc.

Group selection for adaptation to multiple-hen cages: humoral immune response.

PubMed

Hester, P Y; Muir, W M; Craig, J V

1996-11-01

A selected line of White Leghorns, which has shown improved survivability and reduced feather loss in large multiple-hen cages, was evaluated for humoral immune response to SRBC under both stressed and unstressed conditions. Three lines of chickens (selected, control, and commercial) were housed in either single- (1 hen) or multiple-hen cages (12 hens, social competition) and subjected to a cold ambient temperature (0 C) at 33 wk of age and to two heating episodes (38 C) at 44 wk of age. Each hen was challenged intravenously with 1 mL of a 7% saline suspension of SRBC at the time that cold exposure was initiated. Hens subjected to high ambient temperatures had been exposed previously to a cold temperature, but were not challenged with SRBC until 16 to 18 h following the end of the second heating episode. Exposure to cold caused immunosuppression in single-caged hens, but not in hens in colony cages. Single- vs colony-caged hens of the control environment challenged with SRBC at 33 wk of age had similar primary hemagglutinin responses to SRBC. Hens subjected to heat experienced immunosuppression at 9 and 12 d following challenge to SRBC when compared to the controls. Hens of multiple-bird cages challenged with antigen at 44 wk of age had a significantly lower hemagglutinin response to SRBC than those reared in single-bird cages. The three lines of genetic stock had similar primary hemagglutinin responses to SRBC; the interactions of genetic stock with cage size or environmental temperature were not significant. It was concluded that genetically selecting hens for survival in multiple-hen cages did not affect their humoral immune response to SRBC.

The Vertical Dynamics of Larval Chironomids on Artificial Substrates in Lake Lido (Bogor, Indonesia)

PubMed Central

Wardiatno, Yusli; Krisanti, Majariana

2013-01-01

The composition and abundance of chironomid larval communities was studied on artificial substrates in Lido Lake, located in Bogor, West Java, Indonesia. The lake is organically enriched as a result of fish farming activity. Seventy two artificial substrates were deployed at three depths (2.0, 3.5 and 5.0 m) at two sites: a cage culture site and a non-cage culture site (control). Larval chironomid larvae were collected 7, 14, 28 and 56 days after the artificial substrates were deployed. In addition, selected physical and chemical parameters of the water were simultaneously measured. Three chironomid subfamilies, the Chironominae, Tanypodinae and Orthocladiinae, were found at both sites. At the cage culture site, both diversity and total abundance were significantly higher at the 2.0 and 3.5 m depths than at the 5.0 m depth, but this was not the case at the non-cage culture site. Based on pooling of the data from all depths, a Mann-Whitney U test showed that the non-cage culture site had a significantly higher diversity and total abundance than the cage culture site. Dissolved oxygen (DO) and turbidity showed significant differences between the 2.0 m depth and the 2 greater depths at the cage culture site, whereas none of the environmental parameters showed significant differences among the three depths at the non-cage culture site. A comparison of the environmental parameters at the same depth at the two sites showed significant differences in turbidity, pH and DO. A Spearman rank correlation analysis at the cage culture site showed that abundance and DO were positively correlated, whereas abundance and turbidity were negatively correlated. However, only pH was negatively correlated with abundance at the non-cage culture site. PMID:24575246

Dynamic free energy surfaces for sodium diffusion in type II silicon clathrates.

PubMed

Slingsby, J G; Rorrer, N A; Krishna, L; Toberer, E S; Koh, C A; Maupin, C M

2016-02-21

Earth abundant semiconducting type II Si clathrates have attracted attention as photovoltaic materials due to their wide band gaps. To realize the semiconducting properties of these materials, guest species that arise during the synthesis process must be completely evacuated from the host cage structure post synthesis. A common guest species utilized in the synthesis of Si clathrates is Na (metal), which templates the clathrate cage formation. Previous experimental investigations have identified that it is possible to evacuate Na from type II clathrates to an occupancy of less than 1 Na per unit cell. This work investigates the energetics, kinetics, and resulting mechanism of Na diffusion through type II Si clathrates by means of biased molecular dynamics and kinetic Monte Carlo simulations. Well-tempered metadynamics has been used to determine the potential of mean force for Na moving between clathrate cages, from which the thermodynamic preferences and transition barrier heights have been obtained. Kinetic Monte Carlo simulations based on the metadynamics results have identified the mechanism of Na diffusion in type II Si clathrates. The overall mechanism consists of a coupled diffusive process linked via electrostatic guest-guest interactions. The large occupied hexakaidechedral cages initially empty their Na guests to adjacent empty large cages, thereby changing the local electrostatic environment around the occupied small pentagonal dodecahedral cages and increasing the probability of Na guests to leave the small cages. This coupled process continues through the cross-over point that is identified as the point where large and small cages are equally occupied by Na guests. Further Na removal results in the majority of guests residing in the large cages as opposed to the small cages, in agreement with experiments, and ultimately a Na free structure.

Stand-alone anchored cage versus cage with plating for single-level anterior cervical discectomy and fusion: a prospective, randomized, controlled study with a 2-year follow-up.

PubMed

Nemoto, Osamu; Kitada, Akira; Naitou, Satoko; Tachibana, Atsuko; Ito, Yuya; Fujikawa, Akira

2015-07-01

To avoid complications associated with plating in anterior cervical discectomy and fusion (ACDF), stand-alone anchored PEEK cage was developed and favourable outcomes with a low rate of dysphasia have been described. The objective of this study was to compare the clinical and radiological outcomes of ACDF using a standalone anchored PEEK cage (PREVAIL; Medtronic Sofamor Danek, Memphis, TN) with those of a PEEK cage with plating in a prospective randomized manner. Fifty patients with single-level cervical radiculopathy were randomly assigned to a PREVAIL or a PEEK cage with plating. Following 3, 6, 12, and 24 months, clinical and radiological outcomes were assessed. The mean surgical time for the patients with a PREVAIL was significantly shorter than that for those with a PEEK cage with plating. The clinical outcomes evaluated by visual analogue scale for pain and the Odom's criteria were comparable between both the groups. Both the groups demonstrated the high fusion rate (92% in PREVAIL; 96% in PEEK cage with plating). The subsidence rate and the improvement of cervical alignment were comparable between both the groups. The incidence of adjacent-level ossification was significantly lower for patients with a PREVAIL than that for those with a PEEK cage with plating. The rate of dysphasia graded by the method of Bazaz and measurement of prevertebral soft tissue swelling indicated no significant differences between both the groups. Our prospective randomized study confirmed that stand-alone anchored PEEK cage is a valid alternative to plating in ACDF with a low rate of adjacent-level ossification. However, the potential to reduce the incidence of dysphasia was not confirmed.

Transition-Metal-Catalyzed Selective Cage B-H Functionalization of o-Carboranes.

PubMed

Quan, Yangjian; Qiu, Zaozao; Xie, Zuowei

2018-02-26

Carboranes are a class of carbon-boron molecular clusters with unusual thermal and chemical stabilities. They have been proved as very useful building blocks in supramolecular design, optoelectronics, nanomaterials, boron neutron capture therapy agents and organometallic/coordination chemistry. Thus, the functionalization of o-carboranes has received growing interests. Over the past decades, most of the works in this area have been focused on cage carbon functionalization as the weakly acidic cage C-H proton can be readily deprotonated by strong bases. In sharp contrast, selective cage B-H activation/functionalization among chemically very similar ten B-H vertices is very challenging. Considering the differences in electron density of ten cage B-H bonds in o-carborane and the nature of transition metal complexes, we have tackled this selectivity issue by means of organometallic chemistry. Our strategy is as follows: using electron-rich transition metal catalysts for the functionalization of the most electron-deficient B(3,6)-H vertices (bonded to both cage CH vertices); using electron-deficient transition-metal catalysts for the functionalization of relatively electron-rich B(8,9,10,12)-H vertices (with no bonding to both cage CH vertices); and using the combination of directing groups and electrophilic transition metal catalysts for the functionalization of B(4,5,7,11)-H vertices (bonded to only one cage CH vertex). Successful applications of such a strategy result in the preparation of a large variety of cage B-functionalized carboranes in a regioselective and catalytic manner, which are inaccessible by other means. It is believed that as this field progresses, other cage B-functionalized carboranes are expected to be synthesized, and the results detailed in this concept article will further these efforts. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The Crystal Structure of a Maxi/Mini-Ferritin Chimera Reveals Guiding Principles for the Assembly of Protein Cages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cornell, Thomas A.; Srivastava, Yogesh; Jauch, Ralf

Cage proteins assemble into nanoscale structures with large central cavities. They play roles, including those as virus capsids and chaperones, and have been applied to drug delivery and nanomaterials. Furthermore, protein cages have been used as model systems to understand and design protein quaternary structure. Ferritins are ubiquitous protein cages that manage iron homeostasis and oxidative damage. Two ferritin subfamilies have strongly similar tertiary structure yet distinct quaternary structure: maxi-ferritins normally assemble into 24-meric, octahedral cages with C-terminal E-helices centered around 4-fold symmetry axes, and mini-ferritins are 12-meric, tetrahedral cages with 3-fold axes defined by C-termini lacking E-domains. To understandmore » the role E-domains play in ferritin quaternary structure, we previously designed a chimera of a maxi-ferritin E-domain fused to the C-terminus of a mini-ferritin. The chimera is a 12-mer cage midway in size between those of the maxi- and mini-ferritin. The research described herein sets out to understand (a) whether the increase in size over a typical mini-ferritin is due to a frozen state where the E-domain is flipped out of the cage and (b) whether the symmetrical preference of the E-domain in the maxi-ferritin (4-fold axis) overrules the C-terminal preference in the mini-ferritin (3-fold axis). With a 1.99 Å resolution crystal structure, we determined that the chimera assembles into a tetrahedral cage that can be nearly superimposed with the parent mini-ferritin, and that the E-domains are flipped external to the cage at the 3-fold symmetry axes.« less

A Geometric Principle May Guide Self-Assembly of Fullerene Cages from Clathrin Triskelia and from Carbon Atoms☆

PubMed Central

Schein, Stan; Sands-Kidner, Michelle

2008-01-01

Abstract Clathrin triskelia and carbon atoms alike self-assemble into a limited selection of fullerene cages (with n three connected vertices, 3n/2 edges, 12 pentagonal faces, and (n−20)/2 hexagonal faces). We show that a geometric constraint—exclusion of head-to-tail dihedral angle discrepancies (DADs)—explains this limited selection as well as successful assembly into such closed cages in the first place. An edge running from a pentagon to a hexagon has a DAD, since the dihedral angles about the edge broaden from its pentagon (tail) end to its hexagon (head) end. Of the 21 configurations of a central face and surrounding faces, six have such DAD vectors arranged head-to-tail. Of the 5770 mathematically possible fullerene cages for n ≤ 60, excluding those with any of the six configurations leaves just 15 cages plus buckminsterfullerene (n = 60), among them the known clathrin cages. Of the 216,739 mathematically possible cages for 60 < n ≤ 84, just the 50 that obey the isolated-pentagon rule, among them known carbon cages, pass. The absence of likely fullerenes for some n (30,34,46,48,52–58,62–68) explains the abundance of certain cages, including buckminsterfullerene. These principles also suggest a “probable roads” path to self-assembly in place of pentagon-road and fullerene-road hypotheses. PMID:17921209

Single transverse-orientation cage via MIS-TLIF approach for the treatment of degenerative lumbar disease: a technical note.

PubMed

Wang, Shan-Jin; Han, Ying-Chao; Pan, Fu-Min; Ma, Bin; Tan, Jun

2015-01-01

Single transverse cage placed in the anterior vertebral column can better maintain lumbar lordosis and sagittal alignment and is frequently used via the lateral transpsoas approach. However, there is no clear description in the literature of the steps required to place the single transverse cage during the instrumented transforaminal lumbar interbody fusion (TLIF) procedure for the treatment of degenerative lumbar disease. The objective of this study is to describe the technique using single transverse-orientation cage when performing TLIF procedures. We present 18 illustrative cases in which single transverse-orientation cage was placed according to a step-by-step technique that can be used during the TLIF procedure. Information acquired included procedure time, intraoperative blood loss and postoperative complications. The preoperative and postoperative Oswestry Disability Index (ODI) and the visual analogue scale (VAS) scores were recorded. Changes in disc height and segmental lordosis were measured at radiographs. The single transverse-orientation cage was successfully placed in 18 patients in a stepwise technique to achieve lumbar fusion. Using this technique, the patients significantly improved clinically and radiographically at postoperative visits. This is the first report demonstrating the safety and efficacy of instrumented TLIF with single transverse-orientation cage for the treatment of degenerative lumbar disease. Single transverse-orientation cage via MIS-TLIF approach can maintain greater lumbar lordosis and avoid the unique complications of lateral transpsoas approach. Understanding the options for cage placement is important for surgeons considering the use of this technique.

Solid-State Gas Adsorption Studies with Discrete Palladium(II) [Pd2 (L)4 ]4+ Cages.

PubMed

Preston, Dan; White, Keith F; Lewis, James E M; Vasdev, Roan A S; Abrahams, Brendan F; Crowley, James D

2017-08-04

The need for effective CO 2 capture systems remains high, and due to their tunability, metallosupramolecular architectures are an attractive option for gas sorption. While the use of extended metal organic frameworks for gas adsorption has been extensively explored, the exploitation of discrete metallocage architectures to bind gases remains in its infancy. Herein the solid state gas adsorption properties of a series of [Pd 2 (L) 4 ] 4+ lantern shaped coordination cages (L = variants of 2,6-bis(pyridin-3-ylethynyl)pyridine), which had solvent accessible internal cavities suitable for gas binding, have been investigated. The cages showed little interaction with dinitrogen gas but were able to take up CO 2 . The best performing cage reversibly sorbed 1.4 mol CO 2 per mol cage at 298 K, and 2.3 mol CO 2 per mol cage at 258 K (1 bar). The enthalpy of binding was calculated to be 25-35 kJ mol -1 , across the number of equivalents bound, while DFT calculations on the CO 2 binding in the cage gave ΔE for the cage-CO 2 interaction of 23-28 kJ mol -1 , across the same range. DFT modelling suggested that the binding mode is a hydrogen bond between the carbonyl oxygen of CO 2 and the internally directed hydrogen atoms of the cage. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

StreptomycesInforSys: A web-enabled information repository

PubMed Central

Jain, Chakresh Kumar; Gupta, Vidhi; Gupta, Ashvarya; Gupta, Sanjay; Wadhwa, Gulshan; Sharma, Sanjeev Kumar; Sarethy, Indira P

2012-01-01

Members of Streptomyces produce 70% of natural bioactive products. There is considerable amount of information available based on polyphasic approach for classification of Streptomyces. However, this information based on phenotypic, genotypic and bioactive component production profiles is crucial for pharmacological screening programmes. This is scattered across various journals, books and other resources, many of which are not freely accessible. The designed database incorporates polyphasic typing information using combinations of search options to aid in efficient screening of new isolates. This will help in the preliminary categorization of appropriate groups. It is a free relational database compatible with existing operating systems. A cross platform technology with XAMPP Web server has been used to develop, manage, and facilitate the user query effectively with database support. Employment of PHP, a platform-independent scripting language, embedded in HTML and the database management software MySQL will facilitate dynamic information storage and retrieval. The user-friendly, open and flexible freeware (PHP, MySQL and Apache) is foreseen to reduce running and maintenance cost. Availability www.sis.biowaves.org PMID:23275736

Polyphasic characterization of Gluconacetobacter diazotrophicus isolates obtained from different sugarcane varieties

PubMed Central

Guedes, Helma V.; dos Santos, Samuel T.; Perin, Liamara; Teixeira, Kátia R. dos S.; Reis, Veronica M.; Baldani, José I.

2008-01-01

A polyphasic approach was applied to characterize 35 G. diazotrophicus isolates obtained from sugarcane varieties cultivated in Brazil. The isolates were analyzed by phenotypic (use of different carbon sources) and genotypic tests (ARDRA and RISA–RFLP techniques). Variability among the isolates was observed in relation to the carbon source use preference. Glucose and sucrose were used by all isolates in contrast to myo-inositol, galactose and ribose that were not metabolized. The results of the analysis showed the presence of two groups clustered at 68% of similarity. The genetic distance was higher when RISA-RFLP analysis was used. Analysis of 16S rDNA sequences from isolates showed that all of them belonged to the G. diazotrophicus species. Neither effect of the plant part nor sugarcane variety was observed during the cluster analysis. The observed metabolic and genetic variability will be helpful during the strain selection studies for sugarcane inoculation in association with sugarcane breeding programs. PMID:24031296

Yersinia pekkanenii sp. nov.

PubMed

Murros-Kontiainen, Anna; Johansson, Per; Niskanen, Taina; Fredriksson-Ahomaa, Maria; Korkeala, Hannu; Björkroth, Johanna

2011-10-01

The taxonomic position of three strains from water, soil and lettuce samples was studied by using a polyphasic taxonomic approach. The strains were reported to lack the virulence-encoding genes inv and virF in a previous study. Controversially, API 20 E and some other phenotypic tests suggested that the strains belong to Yersinia pseudotuberculosis, which prompted this polyphasic taxonomic study. In both the phylogenetic analyses of four housekeeping genes (glnA, gyrB, recA and HSP60) and numerical analyses of HindIII and EcoRI ribopatterns, the strains formed a separate group within the genus Yersinia. Analysis of the 16S rRNA gene sequences showed that the strains were related to Yersinia aldovae and Yersinia mollaretii, but DNA-DNA hybridization analysis differentiated them from these species. Based on the results of the phylogenetic and DNA-DNA hybridization analyses, a novel species, Yersinia pekkanenii sp. nov., is proposed. The type strain is ÅYV7.1KOH2(T) ( = DSM 22769(T)  = LMG 25369(T)).

StreptomycesInforSys: A web-enabled information repository.

PubMed

Jain, Chakresh Kumar; Gupta, Vidhi; Gupta, Ashvarya; Gupta, Sanjay; Wadhwa, Gulshan; Sharma, Sanjeev Kumar; Sarethy, Indira P

2012-01-01

Members of Streptomyces produce 70% of natural bioactive products. There is considerable amount of information available based on polyphasic approach for classification of Streptomyces. However, this information based on phenotypic, genotypic and bioactive component production profiles is crucial for pharmacological screening programmes. This is scattered across various journals, books and other resources, many of which are not freely accessible. The designed database incorporates polyphasic typing information using combinations of search options to aid in efficient screening of new isolates. This will help in the preliminary categorization of appropriate groups. It is a free relational database compatible with existing operating systems. A cross platform technology with XAMPP Web server has been used to develop, manage, and facilitate the user query effectively with database support. Employment of PHP, a platform-independent scripting language, embedded in HTML and the database management software MySQL will facilitate dynamic information storage and retrieval. The user-friendly, open and flexible freeware (PHP, MySQL and Apache) is foreseen to reduce running and maintenance cost. www.sis.biowaves.org.

Plastic cages to protect Douglas-fir seedlings from animal damage in western Oregon.

Treesearch

Glen C. Crouch

1980-01-01

Effects of plastic mesh cages designed to protect Douglas-fir seedlings from animals were evaluated in western Oregon. In two tests over 5-year periods, caging increased survival by 0 and 13 percent and increased height growth by 0.8 and 1.2 feet compared with uncaged trees. Benefits from caging might have been greater if damage had been more prevalent during the tests...

Final Report for DUSEL R&D: BetaCage: A Screener of Ultra-Low-Level Radioactive Surface Contamination

DOE Office of Scientific and Technical Information (OSTI.GOV)

Golwala, Sunil R.

2013-12-20

The eventual full-size, radiopure BetaCage will be a low-background, atmospheric-pressure neon drift chamber with unprecedented sensitivity to emitters of low-energy electrons and alpha particles. We expect that the prototype BetaCage already developed will be an excellent screener of alpha particles. Both the prototype and final BetaCage will provide new infrastructure for rare-event science.

Extended cage adjustable speed electric motors and drive packages

DOEpatents

Hsu, John S.

1999-01-01

The rotor cage of a motor is extended, a second stator is coupled to this extended rotor cage, and the windings have the same number of poles. The motor torque and speed can be controlled by either injecting energy into or extracting energy out from the rotor cage. The motor produces less harmonics than existing doubly-fed motors. Consequently, a new type of low cost, high efficiency drive is produced.

Acute neurological symptoms during hypobaric exposure: consider cerebral air embolism.

PubMed

Weenink, Robert P; Hollmann, Markus W; van Hulst, Robert A

2012-11-01

Cerebral arterial gas embolism (CAGE) is well known as a complication of invasive medical procedures and as a risk in diving and submarine escape. In the underwater environment, CAGE is caused by trapped air, which expands and leads to lung vessel rupture when ambient pressure decreases during ascent. Pressure decrease also occurs during hypobaric activities such as flying and, therefore, CAGE may theoretically be a risk in hypobaric exposure. We reviewed the available literature on this subject. Identified were 12 cases of CAGE due to hypobaric exposure. Based on these cases, we discuss pathophysiology, diagnosis, and treatment of CAGE due to hypobaric exposure. The low and slow pressure decrease during most hypobaric activities (as opposed to diving) account for the low incidence of CAGE during these exposures and suggest that severe air trapping must be present to cause barotrauma. This is also suggested by the large prevalence of air filled cysts in the case reports reviewed. We recommend considering CAGE in all patients presenting with acute central neurological injury during or shortly after pressure decrease such as flying. A CT scan of head and chest should be performed in these patients. Treatment with hyperbaric oxygen therapy should be initiated as soon as possible in cases of proven or probable CAGE.

Validation of an automatic system (DoubleCage) for detecting the location of animals during preference tests.

PubMed

Tsai, P P; Nagelschmidt, N; Kirchner, J; Stelzer, H D; Hackbarth, H

2012-01-01

Preference tests have often been performed for collecting information about animals' acceptance of environmental refinement objects. In numerous published studies animals were individually tested during preference experiments, as it is difficult to observe group-housed animals with an automatic system. Thus, videotaping is still the most favoured method for observing preferences of socially-housed animals. To reduce the observation workload and to be able to carry out preference testing of socially-housed animals, an automatic recording system (DoubleCage) was developed for determining the location of group-housed animals in a preference test set-up. This system is able to distinguish the transition of individual animals between two cages and to record up to 16 animals at the same time (four animals per cage). The present study evaluated the reliability of the DoubleCage system. The data recorded by the DoubleCage program and the data obtained by human observation were compared. The measurements of the DoubleCage system and manual observation of the videotapes are comparable and significantly correlated (P < 0.0001) with good agreement. Using the DoubleCage system enables precise and reliable recording of the preferences of group-housed animals and a considerable reduction of animal observation time.

Zero-profile anchored cage reduces risk of postoperative dysphagia compared with cage with plate fixation after anterior cervical discectomy and fusion.

PubMed

Xiao, ShanWen; Liang, ZhuDe; Wei, Wu; Ning, JinPei

2017-04-01

To compare the rate of postoperative dysphagia between zero-profile anchored cage fixation (ZPC group) and cage with plate fixation (CP group) after anterior cervical discectomy and fusion (ACDF). A meta-analysis of cohort studies between zero-profile anchored cage and conventional cage with plate fixation after ACDF for the treatment of cervical diseases from 2008 to May 2016. An extensive search of studies was performed in PubMed, Medline, Embase, Cochrane library and Google Scholar. Dysphagia rate was extracted. Data analysis was conducted with RevMan 5.2. Sixteen trials involving 1066 patients were included in this meta-analysis. The results suggested that the ZPC group were associated with lower incidences of dysphagia than the CP group at postoperative immediately, 2 weeks, 2, 3, 6 and 12 months. In subgroup analysis, although significant differences were only found in the mild dysphagia at 3 and 6 months postoperatively and in the moderate dysphagia at 2 weeks after surgery; the ZPC group had a lower rate of postoperative dysphagia than the CCP group in short, medium and long term follow-up periods. Zero-profile anchored cage had a lower risk of postoperative dysphagia than cage with plate.

Effect of curcumin caged silver nanoparticle on collagen stabilization for biomedical applications.

PubMed

Srivatsan, Kunnavakkam Vinjimur; Duraipandy, N; Begum, Shajitha; Lakra, Rachita; Ramamurthy, Usha; Korrapati, Purna Sai; Kiran, Manikantan Syamala

2015-04-01

The current study aims at understanding the influence of curcumin caged silver nanoparticle (CCSNP) on stability of collagen. The results indicated that curcumin caged silver nanoparticles efficiently stabilize collagen, indicated by enhanced tensile strength, fibril formation and viscosity. The tensile strength of curcumin caged silver nanoparticle cross-linked collagen and elongation at break was also found to be higher than glutaraldehyde cross-linked collagen. The physicochemical characteristics of curcumin caged nanoparticle cross-linked collagen exhibited enhanced strength. The thermal properties were also good with both thermal degradation temperature and hydrothermal stability higher than native collagen. CD analysis showed no structural disparity in spite of superior physicochemical properties suggesting the significance of curcumin caged nanoparticle mediated cross-linking. The additional enhancement in the stabilization of collagen could be attributed to multiple sites for interaction with collagen molecule provided by curcumin caged silver nanoparticles. The results of cell proliferation and anti-microbial activity assays indicated that curcumin caged silver nanoparticles promoted cell proliferation and inhibited microbial growth making it an excellent biomaterial for wound dressing application. The study opens scope for nano-biotechnological strategies for the development of alternate non-toxic cross-linking agents facilitating multiple site interaction thereby improving therapeutic values to the collagen for biomedical application. Copyright © 2015 Elsevier B.V. All rights reserved.

High pressure oxygen turbopump bearing cage stability analyses. [space shuttle main engine

NASA Technical Reports Server (NTRS)

Merriman, T. L.; Kannel, J. W.

1984-01-01

The low service life of the high pressure oxygen turbopump (HPOTP) bearings used in the space shuttle main engine was examined by use of the Battelle "BASDAP' bearing computer stability model. The dynamic instability of the bearing cage resulted in excessive wear and eventual failure of the unit. By maintaining a cage/race clearance of no more than 0.25 millimeters (0.010 inches), ball/pocket clearance of no less than 0.54 millimeters (0.025 inches), dynamic balancing of the cages, and maintaining adequate lubricant films between the balls and races, cage instability and subsequent bearing degradation can be reduced.

Omni-directional and holonomic rolling platform with decoupled rotational and translational degrees of freedom

DOEpatents

Pin, F.G.; Killough, S.M.

1994-12-20

A wheel assembly includes a support, a cage rotatably mounted on the support and having a longitudinal rotation axis, a first ball wheel rotatably mounted in the cage and having a rotation axis orthogonal to the rotation axis of the cage, and a second ball wheel rotatably mounted in the cage and having a rotation axis orthogonal to the rotation axis or the cage and to the rotation axis of the first ball wheel. A control circuit includes a photodetector signal which indicates ground contact for each ball wheel, and a tachometer which indicates actual drive shaft velocity. 6 figures.

Omni-directional and holonomic rolling platform with decoupled rotational and translational degrees of freedom

DOEpatents

Pin, Francois G.; Killough, Stephen M.

1994-01-01

A wheel assembly includes a support, a cage rotatably mounted on the support and having a longitudinal rotation axis, a first ball wheel rotatably mounted in the cage and having a rotation axis orthogonal to the rotation axis of the cage, and a second ball wheel rotatably mounted in the cage and having a rotation axis orthogonal to the rotation axis or the cage and to the rotation axis of the first ball wheel. A control circuit includes a photodetector signal which indicates ground contact for each ball wheel, and a tachometer which indicates actual drive shaft velocity.

The cag PAI is intact and functional but HP0521 varies significantly in Helicobacter pylori isolates from Malaysia and Singapore.

PubMed

Schmidt, H-M A; Andres, S; Nilsson, C; Kovach, Z; Kaakoush, N O; Engstrand, L; Goh, K-L; Fock, K M; Forman, D; Mitchell, H

2010-04-01

Helicobacter pylori-related disease is at least partially attributable to the genotype of the infecting strain, particularly the presence of specific virulence factors. We investigated the prevalence of a novel combination of H. pylori virulence factors, including the cag pathogenicity island (PAI), and their association with severe disease in isolates from the three major ethnicities in Malaysia and Singapore, and evaluated whether the cag PAI was intact and functional in vitro. Polymerase chain reaction (PCR) was used to detect dupA, cagA, cagE, cagT, cagL and babA, and to type vacA, the EPIYA motifs, HP0521 alleles and oipA ON status in 159 H. pylori clinical isolates. Twenty-two strains were investigated for IL-8 induction and CagA translocation in vitro. The prevalence of cagA, cagE, cagL, cagT, babA, oipA ON and vacA s1 and i1 was >85%, irrespective of the disease state or ethnicity. The prevalence of dupA and the predominant HP0521 allele and EPIYA motif varied significantly with ethnicity (p < 0.05). A high prevalence of an intact cag PAI was found in all ethnic groups; however, no association was observed between any virulence factor and disease state. The novel association between the HP0521 alleles, EPIYA motifs and host ethnicity indicates that further studies to determine the function of this gene are important.

Octa- and hexametallic iron(III)-potassium phosphonate cages.

PubMed

Gopal, Kandasamy; Tuna, Floriana; Winpenny, Richard E P

2011-12-07

Two new iron(III)-potassium phosphonate cage complexes with {K(2)Fe(6)} and {K(2)Fe(4)} cores are reported. Magnetic studies reveal antiferromagnetic interactions between the Fe(III) centres occur in these cages.

Provision Of Carbon Nanotube Bucky Paper Cages For Immune Shielding Of Cells, Tissues, and Medical Devices

NASA Technical Reports Server (NTRS)

Loftus, David J. (Inventor)

2006-01-01

System and method for enclosing cells and/or tissue, for purposes of growth, cell differentiation, suppression of cell differentiation, biological processing and/or transplantation of cells and tissues (biological inserts), and for secretion, sensing and monitoring of selected chemical substances and activation of gene expression of biological inserts implanted into a human body. Selected cells and/or tissue are enveloped in a "cage" that is primarily carbon nanotube Bucky paper, with a selected thickness and porosity. Optionally, selected functional groups, proteins and/or peptides are attached to the carbon nanotube cage, or included within the cage, to enhance the growth and/or differentiation of the cells and/or tissue, to select for certain cellular sub-populations, to optimize certain functions of the cells and/or tissue and/or to optimize the passage of chemicals across the cage surface(s). A cage system is also used as an immuns shield and to control operation of a nano-device or macroscopic device, located within the cage, to provide or transform a selected chemical and/or a selected signal.

Thermodynamics and kinetics of gas storage in porous liquids

DOE PAGES

Zhang, Fei; Yang, Fengchang; Huang, Jingsong; ...

2016-07-05

The recent synthesis of organic molecular liquids with permanent porosity (Giri et al., Nature, 2015, 527, 216) opens up exciting new avenues for gas capture, storage, and separation. Using molecular dynamics simulations, we study the thermodynamics and kinetics for the storage of CH 4, CO 2, and N 2 molecules in porous liquids consisting of crown-ether substituted cage molecules in a 15-crown-5 solvent. It is found that the gas storage capacity per cage molecule follows the order of CH 4 > CO 2 > N 2, which does not correlate simply with the size of gas molecules. Different gas moleculesmore » are stored inside the cage differently, e.g., CO 2 molecules prefer the cage s core while CH 4 molecules favor both the core and the branch regions. All gas molecules considered can enter the cage essentially without energy barriers, and their dynamics inside the cage are only slightly hindered by the nanoscale confinement. In addition, all gas molecules can leave the cage on nanosecond time scale by overcoming a modest energy penalty. The molecular mechanisms of these observations are clarified.« less

Thermodynamics and kinetics of gas storage in porous liquids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Fei; Yang, Fengchang; Huang, Jingsong

The recent synthesis of organic molecular liquids with permanent porosity (Giri et al., Nature, 2015, 527, 216) opens up exciting new avenues for gas capture, storage, and separation. Using molecular dynamics simulations, we study the thermodynamics and kinetics for the storage of CH 4, CO 2, and N 2 molecules in porous liquids consisting of crown-ether substituted cage molecules in a 15-crown-5 solvent. It is found that the gas storage capacity per cage molecule follows the order of CH 4 > CO 2 > N 2, which does not correlate simply with the size of gas molecules. Different gas moleculesmore » are stored inside the cage differently, e.g., CO 2 molecules prefer the cage s core while CH 4 molecules favor both the core and the branch regions. All gas molecules considered can enter the cage essentially without energy barriers, and their dynamics inside the cage are only slightly hindered by the nanoscale confinement. In addition, all gas molecules can leave the cage on nanosecond time scale by overcoming a modest energy penalty. The molecular mechanisms of these observations are clarified.« less

Consumption of particulate wastes derived from cage fish farming by aggregated wild fish. An experimental approach.

PubMed

Ballester-Moltó, M; Sanchez-Jerez, P; Aguado-Giménez, F

2017-09-01

Particulate wastes derived from cage fish farming are a trophic resource used by wild fish. This study assesses waste consumption by wild fish and the impact on the final balance of wastes. Consumption was determined according to the difference between the particulate matter exiting the cages and that reaching 5 m away at three different depths, in the presence and absence of wild fish. Wild fish around the experimental cages were counted during feeding and non-feeding periods. A weighted abundance of 1057 fish 1000 m -3 consumed 17.75% of the particulate wastes exiting the cages, on average. Consumption was higher below the cages, where waste outflow was greater. However, waste removal by wild fish was noteworthy along the shallow and deep sides of the cages. Wild fish diminished the net particulate wastes by about 14%, transforming them into more easily dispersible and less harmful wastes. This study demonstrates the mitigating potential of wild fish in reducing environmental impact. Copyright © 2017 Elsevier Ltd. All rights reserved.

Can an Endplate-conformed Cervical Cage Provide a Better Biomechanical Environment than a Typical Non-conformed Cage?: A Finite Element Model and Cadaver Study.

PubMed

Zhang, Fan; Xu, Hao-Cheng; Yin, Bo; Xia, Xin-Lei; Ma, Xiao-Sheng; Wang, Hong-Li; Yin, Jun; Shao, Ming-Hao; Lyu, Fei-Zhou; Jiang, Jian-Yuan

2016-08-01

To evaluate the biomechanical characteristics of endplate-conformed cervical cages by finite element method (FEM) analysis and cadaver study. Twelve specimens (C2 -C7 ) and a finite element model (C3 -C7 ) were subjected to biomechanical evaluations. In the cadaver study, specimens were randomly assigned to intact (I), endplate-conformed (C) and non-conformed (N) groups with C4-5 discs as the treated segments. The morphologies of the endplate-conformed cages were individualized according to CT images of group C and the cages fabricated with a 3-D printer. The non-conformed cages were wedge-shaped and similar to commercially available grafts. Axial pre-compression loads of 73.6 N and moment of 1.8 Nm were used to simulate flexion (FLE), extension (EXT), lateral bending (LB) and axial rotation (AR). Range of motion (ROM) at C4-5 of each specimen was recorded and film sensors fixed between the cages and C5 superior endplates were used to detect interface stress. A finite element model was built based on the CT data of a healthy male volunteer. The morphologies of the endplate-conformed and wedge-shaped, non-conformed cervical cages were both simulated by a reverse engineering technique and implanted at the segment of C4-5 in the finite element model for biomechanical evaluation. Force loading and grouping were similar to those applied in the cadaver study. ROM of C4-5 in group I were recorded to validate the finite element model. Additionally, maximum cage-endplate interface stresses, stress distribution contours on adjoining endplates, intra-disc stresses and facet loadings at adjacent segments were measured and compared between groups. In the cadaver study, Group C showed a much lower interface stress in all directions of motion (all P < 0.05) and the ROM of C4-5 was smaller in FLE-EXT (P = 0.001) but larger in AR (P = 0.017). FEM analysis produced similar results: the model implanted with an endplate-conformed cage presented a lower interface stress with a more uniform stress distribution than that implanted with a non-conformed cage. Additionally, intra-disc stress and facet loading at the adjacent segments were obviously increased in both groups C and N, especially those at the supra-jacent segments. However, stress increase was milder in group C than in group N for all directions of motion. Endplate-conformed cages can decrease cage-endplate interface stress in all directions of motion and increase cervical stability in FLE-EXT. Additionally, adjacent segments are possibly protected because intra-disc stress and facet loading are smaller after endplate-conformed cage implantation. However, axial stability was reduced in group C, indicating that endplate-conformed cage should not be used alone and an anterior plate system is still important in anterior cervical discectomy and fusion. © 2016 Chinese Orthopaedic Association and John Wiley & Sons Australia, Ltd.

Extended cage adjustable speed electric motors and drive packages

DOEpatents

Hsu, J.S.

1999-03-23

The rotor cage of a motor is extended, a second stator is coupled to this extended rotor cage, and the windings have the same number of poles. The motor torque and speed can be controlled by either injecting energy into or extracting energy out from the rotor cage. The motor produces less harmonics than existing doubly-fed motors. Consequently, a new type of low cost, high efficiency drive is produced. 12 figs.

Use of Li.sub.2[B.sub.12H.sub.12] salt to absorb water into polymers

DOEpatents

Eastwood, Eric A.; Bowen, III, Daniel E.

2016-08-30

Methods of adjusting the properties of a composition are provided. The compositions comprise a polymer-containing matrix and a filler comprising a hygroscopic salt. Preferred such salts comprise a cage compound selected from the group consisting of borane cage compounds, carborane cage compounds, metal complexes thereof, residues thereof, mixtures thereof, and/or agglomerations thereof, where the cage compound is not covalently bound to the matrix polymer.

Smallest fullerene-like silicon cage stabilized by a V(2) unit.

PubMed

Xu, Hong-Guang; Kong, Xiang-Yu; Deng, Xiao-Jiao; Zhang, Zeng-Guang; Zheng, Wei-Jun

2014-01-14

We conducted a combined anion photoelectron spectroscopy and density functional theory study on V2Si20 cluster. Our results show that the V2Si20 cluster has an elongated dodecahedron cage structure with a V2 unit encapsulated inside the cage. It is the smallest fullerene-like silicon cage and can be used as building block to make cluster-assembled materials, such as pearl-chain style nanowires.

Smallest fullerene-like silicon cage stabilized by a V2 unit

NASA Astrophysics Data System (ADS)

Xu, Hong-Guang; Kong, Xiang-Yu; Deng, Xiao-Jiao; Zhang, Zeng-Guang; Zheng, Wei-Jun

2014-01-01

We conducted a combined anion photoelectron spectroscopy and density functional theory study on V2Si20 cluster. Our results show that the V2Si20 cluster has an elongated dodecahedron cage structure with a V2 unit encapsulated inside the cage. It is the smallest fullerene-like silicon cage and can be used as building block to make cluster-assembled materials, such as pearl-chain style nanowires.

In silico design of supramolecules from their precursors: odd-even effects in cage-forming reactions.

PubMed

Jelfs, Kim E; Eden, Edward G B; Culshaw, Jamie L; Shakespeare, Stephen; Pyzer-Knapp, Edward O; Thompson, Hugh P G; Bacsa, John; Day, Graeme M; Adams, Dave J; Cooper, Andrew I

2013-06-26

We synthesize a series of imine cage molecules where increasing the chain length of the alkanediamine precursor results in an odd-even alternation between [2 + 3] and [4 + 6] cage macrocycles. A computational procedure is developed to predict the thermodynamically preferred product and the lowest energy conformer, hence rationalizing the observed alternation and the 3D cage structures, based on knowledge of the precursors alone.

In silico Design of Supramolecules from Their Precursors: Odd–Even Effects in Cage-Forming Reactions

PubMed Central

2013-01-01

We synthesize a series of imine cage molecules where increasing the chain length of the alkanediamine precursor results in an odd–even alternation between [2 + 3] and [4 + 6] cage macrocycles. A computational procedure is developed to predict the thermodynamically preferred product and the lowest energy conformer, hence rationalizing the observed alternation and the 3D cage structures, based on knowledge of the precursors alone. PMID:23745577

Electronic structure, stability and magnetic properties of small M1-2Cr (M = Fe, Co, and Ni) alloy encapsulated inside a (BN)48 cage

NASA Astrophysics Data System (ADS)

Liang, Wenjuan; Jia, Jianfeng; Lv, Jin; Wu, Haishun

2015-09-01

The geometrical structure and magnetic properties of M1-2Cr (M = Fe, Co, and Ni) alloy clusters inside a (BN)48 cage were calculated at the BPW91/LANL2DZ level of theory. The doping with Cr significantly changed the magnetic properties of the transition-metal clusters. When M1-2Cr alloys were placed inside a (BN)48 cage, the alloy clusters interacted strongly with the cage, and the M1-2Cr@(BN)48 clusters showed high stability. Moreover, Cr-doped magnetic metal clusters preferably occupied positions off-center and near the hexagonal rings of (BN)48 cages. Thus, the (BN)48 cages can be used to increase the stability of M1-2Cr alloys, and retain their magnetic nature, except for CoCr and Ni2Cr clusters.

Optimization of mosquito egg production under mass rearing setting: effects of cage volume, blood meal source and adult population density for the malaria vector, Anopheles arabiensis.

PubMed

Mamai, Wadaka; Bimbile-Somda, Nanwintoum S; Maiga, Hamidou; Juarez, José Guillermo; Muosa, Zaynab A I; Ali, Adel Barakat; Lees, Rosemary Susan; Gilles, Jeremie R L

2017-01-24

Anopheles arabiensis is one of the major malaria vectors that put millions of people in endemic countries at risk. Mass-rearing of this mosquito is crucial for strategies that use sterile insect technique to suppress vector populations. The sterile insect technique (SIT) package for this mosquito species is being developed by the Insect Pest Control Subprogramme of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture. To improve mass-rearing outcomes for An. arabiensis, the question of whether the egg production by females would be affected by the size of the adult holding cages, the source of the blood meal and the total number of pupae that could be loaded into the cages was addressed and finally the impact of adding additional pupae to the cage daily to maintain adult numbers on egg productivity assessed. Mass production cages of two different volumes, two different sources of blood meal (bovine and porcine) and two different population densities (cages originally loaded with either 15,000 or 20,000 pupae) were tested and evaluated on the basis of eggs produced/cage or per female. Males and females pupae with a ratio of 1:1 were added to the cages at day 1 and 2 of pupation. The emerging adults had constant access to 5% sugar solution and blood fed via the Hemotek membrane feeding system. Eggs were collected either twice a week or daily. A generalized linear model was used to identify factors which gave significantly higher egg production. Neither cage volume nor blood meal source affected egg production per cage or per female. However, increasing population density to 20,000 pupae had a negative effect on eggs produced per cage and per female. Although high density negatively impacted egg production, adding 1000 daily additional pupae compensating for daily mortality resulted in a substantial increase in egg production. Moreover, in all tests the first and the third egg batches collected were significantly higher than others eggs batches. With the equipment and protocols described here and routinely used at the Insect Pest Control Laboratory (IPCL), it was possible to produce up to 120,000 eggs/cage/day. These results demonstrated that 15,000 is the optimal number of pupae to be loaded into the Anopheles Mass production cages. Under this condition, an average of 40 eggs per female was obtained for five gonotrophic cycles. However, an improvement in egg production can be achieved by daily addition, to the original 15,000 pupae, of one thousand pupae a day. Interestingly, feeding females with bovine or porcine blood using both large and small versions of the mass production cage did not affect egg productivity.

Comparison of behaviour, performance and mortality in restricted and ad libitum-fed growing rabbits.

PubMed

Dalmau, A; Abdel-Khalek, A M; Ramon, J; Piles, M; Sanchez, J P; Velarde, A; Rafel, O

2015-07-01

The objective of this study was to determine whether rabbits fed in a restricted regimen (75%) showed increased competition for feeding, drinking and use of specific areas of the cages as compared with those provided feed ad libitum. This evaluation was carried out by measuring their space utilisation in the cage, the incidence of agonistic behaviour and rates of mortality. In total, 504 rabbits between 31 and 66 days of age were used in this study. A total of 200 heavy-weight rabbits and 56 light-weight rabbits were randomly housed in 32 cages, each cage containing eight rabbits: 25 cages housing heavy rabbits and seven cages housing the light-weight ones. They were all fed ad libitum (AD). In addition, a total of 208 heavy-weight rabbits and 40 light-weight rabbits were randomly housed in 31 cages, each of them containing eight rabbits: 26 cages housing heavy weight rabbits and five cages housing light-weight ones. They were all fed a restricted diet (R) regimen. The restriction was calculated to be 75% of the feed consumed by the AD group. The total space available in the cage was 3252 cm(2), with a stocking density of 24.6 animals/m(2). Animals between 32 and 60 days of age from 20 different cages were observed nine times per week (morning or afternoon) by means of scan and focal sampling by one observer. During each period, cages were assessed for 5 min, registering every minute the position of all the animals in relation to Area A (feeder), Area B (central part) or Area C (back and drinker area). The incidence of agonistic behaviour such as displacement, biting and jumping on each other was also assessed. Performance variables such as daily gain and feed conversion ratio, in addition to general health status and mortality rates, were recorded for all rabbits. When the rabbits were under restricted feeding, the competition for feed and drink increased with clear signs of agonistic behaviour such as biting, displacement and animals jumping on top of each other. Although this competition was maintained during the entire growing period, the BW homogeneity between animals in the same cage was similar in both cases, suggesting that all animals could consume similar quantities of feed. The possible advantages of a restricted diet, such as better feed conversion ratio, were observed in this study only in the last few weeks of the growing period.

Frequency and Duration of Fecal Shedding of Salmonella Enteritidis by Experimentally Infected Laying Hens Housed in Enriched Colony Cages at Different Stocking Densities

PubMed Central

Gast, Richard K.; Guraya, Rupa; Jones, Deana R.; Anderson, Kenneth E.; Karcher, Darrin M.

2017-01-01

Human infections with Salmonella Enteritidis are often attributed to the consumption of contaminated eggs, so the prevalence of this pathogen in egg-laying poultry is an important public health risk factor. Numerous and complex environmental influences on Salmonella persistence and transmission are exerted by management practices and housing facilities used in commercial egg production. In recent years, the animal welfare implications of poultry housing systems have guided the development of alternatives to traditional cage-based housing, but their food safety consequences are not yet fully understood. The present study assessed the effects of different bird stocking densities on the frequency and duration of fecal shedding of S. Enteritidis in groups of experimentally infected laying hens housed in colony cages enriched with perching and nesting areas. In two trials, groups of laying hens were distributed at two stocking densities (648 and 973 cm2/bird) into enriched colony cages and (along with a group housed in conventional cages at 648 cm2/bird) orally inoculated with doses of 1.0 × 108 cfu of S. Enteritidis. At 10 weekly postinoculation intervals, samples of voided feces were collected from beneath each cage and cultured to detect S. Enteritidis. Fecal shedding of S. Enteritidis was detected for up to 10 weeks postinoculation by hens in all three housing treatment groups. The overall frequency of positive fecal cultures was significantly (P < 0.05) greater from conventional cages than from enriched colony cages (at the lower stocking density) for the total of all sampling dates (45.0 vs. 33.3%) and also for samples collected at 4–9 weeks postinfection. Likewise, the frequency of S. Enteritidis isolation from feces from conventional cages was significantly greater than from enriched colony cages (at the higher hen stocking density) for the sum of all samples (45.0 vs. 36.7%) and at 6 weeks postinoculation. Moreover, the frequency of S. Enteritidis fecal recovery from enriched colony cages at the higher hen stocking was significantly greater than from similar cages at the lower stocking density for all 10 sampling dates combined (39.4 vs. 33.3%). These results suggest that stocking density can affect S. Enteritidis intestinal colonization and fecal shedding in laying hens, but some other difference between conventional and enriched colony cage systems appears to exert an additional influence. PMID:28443289

New insights on pressure, temperature, and chemical stability of CsAlSi5O12, a potential host for nuclear waste

NASA Astrophysics Data System (ADS)

Gatta, G. D.; Brundu, A.; Cappelletti, P.; Cerri, G.; de'Gennaro, B.; Farina, M.; Fumagalli, P.; Guaschino, L.; Lotti, P.; Mercurio, M.

2016-10-01

A Cs-bearing polyphase aggregate with composition (in wt%): 76(1)CsAlSi5O12 + 7(1)CsAlSi2O6 + 17(1)amorphous, was obtained from a clinoptilolite-rich epiclastic rock after a beneficiation process of the starting material (aimed to increase the fraction of zeolite to 90 wt%), cation exchange and then thermal treatment. CsAlSi5O12 is an open-framework compound with CAS topology; CsAlSi2O6 is a pollucite-like material with ANA topology. The thermal stability of this polyphase material was investigated by in situ high- T X-ray powder diffraction, the combined P- T effects by a series of runs with a single-stage piston cylinder apparatus, and its chemical stability following the "availability test" ("AVA test") protocol. A series of additional investigations were performed by WDS-electron microprobe analysis in order to describe the P- T-induced modification of the material texture, and to chemically characterize the starting material and the run products. The "AVA tests" of the polyphase aggregate show an extremely modest release of Cs+: 0.05 mg/g. In response to applied temperature and at room P, CsAlSi5O12 experiences an unquenchable and displacive Ama2-to- Amam phase transition at about 770 K, and the Amam polymorph is stable in its crystalline form up to 1600 K; a crystalline-to-amorphous phase transition occurs between 1600 and 1650 K. In response to the applied P = 0.5 GPa, the crystalline-to-amorphous transition of CsAlSi5O12 occurs between 1670 and 1770 K. This leads to a positive Clapeyron slope (i.e., d P/d T > 0) of the crystalline-to-amorphous transition. When the polyphase aggregate is subjected at P = 0.5 GPa and T > 1770 K, CsAlSi5O12 melts and only CsAlSi2O6 (pollucite-like; dominant) and Cs-rich glass (subordinate) are observed in the quenched sample. Based on its thermo-elastic behavior, P- T phase stability fields, and Cs+ retention capacity, CsAlSi5O12 is a possible candidate for use in the immobilization of radioactive isotopes of Cs, or as potential solid hosts for 137Cs γ-radiation source in sterilization applications. More in general, even the CsAlSi5O12-rich aggregate obtained by a clinoptilolite-rich epiclastic rock appears to be suitable for this type of utilizations.

Mating competitiveness of male Anopheles arabiensis mosquitoes irradiated with a partially or fully sterilizing dose in small and large laboratory cages.

PubMed

Helinski, M E H; Knols, B G J

2008-07-01

Male mating competitiveness is a crucial parameter in many genetic control programs including the sterile insect technique (SIT). We evaluated competitiveness of male Anopheles arabiensis Patton as a function of three experimental variables: (1) small or large cages for mating, (2) the effects of either a partially sterilizing (70 Gy) or fully sterilizing (120 Gy) dose, and (3) pupal or adult irradiation. Irradiated males competed for females with an equal number of unirradiated males. Competitiveness was determined by measuring hatch rates of individually laid egg batches. In small cages, pupal irradiation with the high dose resulted in the lowest competitiveness, whereas adult irradiation with the low dose gave the highest, with the latter males being equal in competitiveness to unirradiated males. In the large cage, reduced competitiveness of males irradiated in the pupal stage was more pronounced compared with the small cage; the males irradiated as adults at both doses performed similarly to unirradiated males. Unexpectedly, males irradiated with the high dose performed better in a large cage than in a small one. A high proportion of intermediate hatch rates was observed for eggs collected in the large cage experiments with males irradiated at the pupal stage. It is concluded that irradiation of adult An. arabiensis with the partially sterilizing dose results in the highest competitiveness for both cage designs. Cage size affected competitiveness for some treatments; therefore, competitiveness determined in laboratory experiments must be confirmed by releases into simulated field conditions. The protocols described are readily transferable to evaluate male competitiveness for other genetic control techniques.

Does impaction of titanium-coated interbody fusion cages into the disc space cause wear debris or delamination?

PubMed

Kienle, Annette; Graf, Nicolas; Wilke, Hans-Joachim

2016-02-01

A large number of interbody fusion cages are made of polyetheretherketone (PEEK). To improve bone on-growth, some are coated with a thin layer of titanium. This coating may fail when subjected to shear loading. The purpose of this testing was to investigate whether impaction of titanium-coated PEEK cages into the disc space can result in wear or delamination of the coating, and whether titanium cages with subtractive surface etching (no coating) are less susceptible to such failure. A biomechanical study was carried out to simulate the impaction process in clinical practice and to evaluate if wear or delamination may result from impaction. Two groups of posterior lumbar interbody fusion cages with a similar geometry were tested: n=6 titanium-coated PEEK and n=6 surface-etched titanium cages. The cages were impacted into the space in between two vertebral body substitutes (polyurethane foam blocks). The two vertebral body substitutes were fixed in a device, through which a standardized axial preload of 390 N was applied. The anterior tip of the cage was positioned at the posterior border of the space between the two vertebral body substitutes. The cages were then inserted using a drop weight with a mass representative of a surgical hammer. The drop weight impacted the insertion instrument at a maximum speed of about 2.6 m/s, which is in the range of the impaction speed in vivo. This was repeated until the cages were fully inserted. The wear particles were captured and analyzed according to the pertinent standards. The surface-etched titanium cages did not show any signs of wear debris or surface damage. In contrast, the titanium-coated PEEK cages resulted in detached wear particles of different sizes (1-191 µm). Over 50% of these particles had a size <10 µm. In median, on 26% of the implants' teeth, the coating was abraded. Full delamination was not observed. In contrast to the surface-etched implants, the titanium-coated PEEK implants lost some coating material. This was visible to the naked eye. More than half of all particles were of a size range that allows phagocytosis. This study shows that titanium-coated implants are susceptible to impaction-related wear debris. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Ncm, a Photolabile Group for Preparation of Caged Molecules: Synthesis and Biological Application

PubMed Central

Muralidharan, Sukumaran; Dirda, Nathaniel D. A.; Katz, Elizabeth J.; Tang, Cha-Min; Bandyopadhyay, Sharba; Kanold, Patrick O.

2016-01-01

Ncm, 6-nitrocoumarin-7-ylmethyl, is a photolabile protective group useful for making “caged” molecules. Ncm marries the reliable photochemistry of 2-nitrobenzyl systems with the excellent stability and spectroscopic properties of the coumarin chromophore. From simple, commercially available starting materials, preparation of Ncm and its caged derivatives is both quick and easy. Photorelease of Ncm-caged molecules occurs on the microsecond time scale, with quantum efficiencies of 0.05–0.08. We report the synthesis and physical properties of Ncm and its caged derivatives. The utility of Ncm-caged glutamate for neuronal photostimulation is demonstrated in cultured hippocampal neurons and in brain slice preparations. PMID:27695074

A Cobalt Supramolecular Triple-Stranded Helicate-based Discrete Molecular Cage

PubMed Central

Mai, Hien Duy; Kang, Philjae; Kim, Jin Kyung; Yoo, Hyojong

2017-01-01

We report a strategy to achieve a discrete cage molecule featuring a high level of structural hierarchy through a multiple-assembly process. A cobalt (Co) supramolecular triple-stranded helicate (Co-TSH)-based discrete molecular cage (1) is successfully synthesized and fully characterized. The solid-state structure of 1 shows that it is composed of six triple-stranded helicates interconnected by four linking cobalt species. This is an unusual example of a highly symmetric cage architecture resulting from the coordination-driven assembly of metallosupramolecular modules. The molecular cage 1 shows much higher CO2 uptake properties and selectivity compared with the separate supramolecular modules (Co-TSH, complex 2) and other molecular platforms. PMID:28262690

Biocentrifuge system capable of exchanging specimen cages while in operational mode

NASA Technical Reports Server (NTRS)

Belew, R. R. (Inventor)

1981-01-01

The centrifuge comprises a generally circular, rotatably mounted frame carrying a plurality of removable and replaceable cages for the animal specimens. Pairs of opposing cages may be removed from the frame while it is rotating by means of a cage exchanger which rotates concentrically within the centrifuge and the speed of which is controlled independently of the frame speed. An image rotator is provided for selective observation of the rotating animals. The system further includes a waste conveyor system, a food supply system, and a water supply system for each cage for creating a life sustaining environment so that the animals can live in the rotating centrifuge for extended periods.

Comparing polychlorinated biphenyl concentrations and patterns in the Saginaw River using sediment, caged fish, and semipermeable membrane devices

USGS Publications Warehouse

Echols, K.R.; Gale, R.W.; Schwartz, T.R.; Huckins, J.N.; Williams, L.L.; Meadows, J.C.; Morse, D.; Petty, J.D.; Orazio, C.E.; Tillitt, D.E.

2000-01-01

Three techniques of assessing bioavailable polychlorinated biphenyls (PCBs) in the Saginaw River, MI, were compared: sediments, caged fish, and semipermeable membrane devices (SPMDs). SPMDs and caged fish were placed in the river for 28 days at five sites where sediments were also sampled. The samples were analyzed for PCB congeners to determine concentrations and patterns. Total PCB concentrations ranged from 33 to 280 ng/g (dry weight) in sediments, 46 to 290 ng/g (wet weight) in caged fish, and 77 to 790 ng/g in SPMDs. Previously reported rates of PCB accumulation by SPMDs were used to estimate aqueous concentrations from the PCB concentrations detected in the SPMDs. Sediment-water partition coefficients were used to estimate aqueous PCB concentrations from sediment. Steady-state bioconcentration factors and depuration rate constants were used to estimate dissolved PCB concentrations from caged channel catfish. Relative PCB patterns from the SPMDs, caged fish, and sediment were compared using principal components analysis. SPMD and sediment samples provide complementary information. Sediments reflect long-term accumulation and weathering, while SPMDs integrate water concentrations only during the sampling period. Because of higher water solubilities of lower-chlorinated PCBs these predominate in the SPMDs as compared to in the fish and sediments. Contaminant profile differences between caged fish and SPMDs are likely due to metabolism and depuration of certain PCB congeners by fish.Three techniques of assessing bioavailable polychlorinated biphenyls (PCBs) in the Saginaw River, Ml, were compared: sediments, caged fish, and semipermeable membrane devices (SPMDs). SPMDs and caged fish were placed in the river for 28 days at five sites where sediments were also sampled. The samples were analyzed for PCB congeners to determine concentrations and patterns. Total PCB concentrations ranged from 33 to 280 ng/g (dry weight) in sediments, 46 to 290 ng/g (wet weight) in caged fish, and 77 to 790 ng/g in SPMDs. Previously reported rates of PCB accumulation by SPMDs were used to estimate aqueous concentrations from the PCB concentrations detected in the SPMDs. Sediment-water partition coefficients were used to estimate aqueous PCB concentrations from sediment. Steady-state bioconcentration factors and depuration rate constants were used to estimate dissolved PCB concentrations from caged channel catfish. Relative PCB patterns from the SPMDs, caged fish, and sediment were compared using principal components analysis. SPMD and sediment samples provide complementary information. Sediments reflect long-term accumulation and weathering, while SPMDs integrate water concentrations only during the sampling period. Because of higher water solubilities of lower-chlorinated PCBs these predominate in the SPMDs as compared to in the fish and sediments. Contaminant profile differences between caged fish and SPMDs are likely due to metabolism and depuration of certain PCB congeners by fish.At five sites in the Saginaw River, MI, PCB concentrations were determined in the summer of 1993 using three methods: sediment analysis, concentrations in caged fish, and concentrations in semipermeable membrane devices (SPMDs). On average, total PCB concentrations in the SPMDs were twice those found in caged fish, and the SPMD-to-fish concentration ratios of di-, tri-, tetra-, and pentaCB homologues were 10.0, 3.0, 2.5, and 1.4, respectively. Average concentrations in the sediments were approximately half those in the SPMDs, and the caged fish showed a greater preponderance of higher log octanol-water partition coefficient PCBs similar to the sediment pattern. On average, the water PCB concentrations estimated from sediment concentrations were five times higher than those calculated from SPMDs and three times higher than those estimated from caged fish. The total PCB concentrations in sediment, caged fish, and SPMDs ranged 33-280, 46-290, and 77-790 ng/g, respectiv

Smallest fullerene-like silicon cage stabilized by a V{sub 2} unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Hong-Guang, E-mail: xuhong@iccas.ac.cn, E-mail: zhengwj@iccas.ac.cn; Kong, Xiang-Yu; Deng, Xiao-Jiao

We conducted a combined anion photoelectron spectroscopy and density functional theory study on V{sub 2}Si{sub 20} cluster. Our results show that the V{sub 2}Si{sub 20} cluster has an elongated dodecahedron cage structure with a V{sub 2} unit encapsulated inside the cage. It is the smallest fullerene-like silicon cage and can be used as building block to make cluster-assembled materials, such as pearl-chain style nanowires.

Computational design and fabrication of a novel bioresorbable cage for tibial tuberosity advancement application.

PubMed

Castilho, Miguel; Rodrigues, Jorge; Vorndran, Elke; Gbureck, Uwe; Quental, Carlos; Folgado, João; Fernandes, Paulo R

2017-01-01

Tibial tuberosity advancement (TTA) is a promising method for the treatment of cruciate ligament rupture in dogs that usually implies the implantation of a titanium cage as bone implant. This cage is non-biodegradable and fails in providing adequate implant-bone tissue integration. The objective of this work is to propose a new process chain for designing and manufacturing an alternative biodegradable cage that can fulfill specific patient requirements. A three-dimensional finite element model (3D FEM) of the TTA system was first created to evaluate the mechanical environment at cage domain during different stages of the dog walk. The cage microstructure was then optimized using a topology optimization tool, which addresses the accessed local mechanical requirements, and at same time ensures the maximum permeability to allow nutrient and oxygen supply to the implant core. The designed cage was then biofabricated by a 3D powder printing of tricalcium phosphate cement. This work demonstrates that the combination of a 3D FEM with a topology optimization approach enabled the design of a novel cage for TTA application with tailored permeability and mechanical properties, that can be successfully 3D printed in a biodegradable bioceramic material. These results support the potential of the design optimization strategy and fabrication method to the development of customized and bioresorbable implants for bone repair. Copyright © 2016 Elsevier Ltd. All rights reserved.

Common experience modifies the reinforcing properties of methamphetamine-injected cage mates but not morphine-injected cage mates in C57 mice.

PubMed

Watanabe, Shigeru

2015-10-01

The aim of this study was to determine whether previous exposure to a drug affects the social facilitation of conditioned place preference (CPP) for a drug-injected cage mate. Twenty-two male C57/BL6J mice received drug injections (methamphetamine or morphine) and 22 male C57/BL6J mice received saline injections. All 44 mice then received CPP training, during which one compartment of a conventional CPP apparatus was associated with a drug-injected cage mate (stimulus mouse) and the other compartment was associated with a saline-injected cage mate (stimulus mouse). The subject mice did not receive any drug injection during this CPP training. Time spent in the compartment associated with the drug-injected cage mate was measured before and after training. Subject mice that had previously received methamphetamine injections showed an increase in the time spent in the compartment associated with the methamphetamine-injected cage mate after CPP training. This effect was not observed in subject mice that had previously received saline injections. Subject mice did not show an increase in the time spent in the compartment associated with the morphine-injected cage mate irrespective of whether they had previously received morphine or saline injections. Therefore, in agreement with previous reports, common experience with methamphetamine induced reinforcing properties, but that with morphine did not.

In situ experiments to assess effects of constraints linked to caging on ecotoxicity biomarkers of the three-spined stickleback (Gasterosteus aculeatus L.).

PubMed

Le Guernic, Antoine; Sanchez, Wilfried; Palluel, Olivier; Bado-Nilles, Anne; Turies, Cyril; Chadili, Edith; Cavalié, Isabelle; Adam-Guillermin, Christelle; Porcher, Jean-Marc; Geffard, Alain; Betoulle, Stéphane; Gagnaire, Béatrice

2016-04-01

The aim of this study was to evaluate the effects of caging constraints on multiple fish biomarkers used during ecotoxicological studies (biometric data, immune and antioxidant systems, and energetic status). Two of these constraints were linked to caging: starvation and fish density in cages, and one in relation to the post-caging handling: a short transport. Three in situ experiments were conducted with three-spined sticklebacks (Gasterosteus aculeatus). The first experiment compared the effects of three densities (low, medium, and high). The second experiment compared effects of starvation in fish fed every two days with fish that were not fed. Finally comparisons between sticklebacks which have suffered a short car transport after caging and sticklebacks killed without preliminary transport were made. The lack of food had no effect on fish energetic reserves but negatively affected their condition index and their immune system. Transport and high density induced oxidative stress, defined as an overproduction of reactive oxygen species and a stimulation of the antioxidant system. These two constraints also harmed the leucocyte viability. In order not to have any impact on ecotoxicity biomarkers during in situ experiments, it is preferable to decrease fish density in cages, prevent transport before dissections, and feed fish when the caging lasts more than two weeks.

Development of perching behavior in 3 strains of pullets reared in furnished cages.

PubMed

Habinski, A M; Caston, L J; Casey-Trott, T M; Hunniford, M E; Widowski, T M

2017-03-01

Furnished rearing cages are becoming more widely available to replace conventional systems for pullets. To date, there is little information on how pullets develop perching behavior in furnished cages or how this varies among strains. The objective of this study was to evaluate the use of perches and a platform in a commercial furnished rearing "Combi-Cage" system by 3 pure-bred heritage strains of pullets (Rhode Island Red, Columbian Rock, and White Leghorn). Each cage had 4 elevated locations: one platform and 3 perches of differing heights and positions in the cage. The length of each cage was visually divided into 4 sections for observation. The number of birds using each section in each location was counted by one observer d per wk at 1200 h (d) from one to 14 wk of age and at 1600 h (night) right after lights were turned off from 4 to 14 wk of age. Mixed model repeated analyses were used to test effects of strain, age, and their interaction on the use of the platform, the 3 perches, and all 4 locations combined (vertical space use) at both time periods. GLM were used to compare overall use of the sections and locations. On average, pullets used vertical space more during the d than at night. There were also effects of age (P < 0.05) and strain (P < 0.05) on the use of the 4 locations in the cage at both time periods. Generally, the Columbian Rocks used the perches and platform the most, and Rhode Island Reds the least. The highest perch in the cage was rarely used and birds showed a preference for perching in sections that were closest to cage walls (P < 0.05). Differences across strains and low use of some perch locations indicate that the design of furnished rearing cages may still require improvements in order to ensure the furnishings are used by pullets as intended. © 2016 Poultry Science Association Inc.

Comparison among perfect-C®, zero-P®, and plates with a cage in single-level cervical degenerative disc disease.

PubMed

Noh, Sung Hyun; Zhang, Ho Yeol

2018-01-25

We intended to analyze the efficacy of a new integrated cage and plate device called Perfect-C for anterior cervical discectomy and fusion (ACDF) to cure single-level cervical degenerative disc disease. We enrolled 148 patients who were subjected to single-level ACDF with one of the following three surgical devices: a Perfect-C implant (41 patients), a Zero-P implant (36 patients), or a titanium plate with a polyetheretherketone (PEEK) cage (71 patients). We conducted a retrospective study to compare the clinical and radiological results among the three groups. The length of the operation, intraoperative blood loss, and duration of hospitalization were significantly lower in the Perfect-C group than in the Zero-P and plate-with-cage groups (P < 0.05). At the last follow-up visit, heterotopic ossification (HO) was not observed in any cases (0%) in the Perfect-C and Zero-P groups but was noted in 21 cases (30%) in the plate-with-cage group. The cephalad and caudal plate-to-disc distance (PDD) and the cephalad and caudal PDD/anterior body height (ABH) were significantly greater in the Perfect-C and Zero-P groups than in the plate-with-cage group (P < 0.05). Subsidence occurred in five cases (14%) in the Perfect-C group, in nine cases (25%) in the Zero-P group, and in 15 cases (21%) in the plate-with-cage group. Fusion occurred in 37 cases (90%) in the Perfect-C group, in 31 cases (86%) in the Zero-P group, and in 68 cases (95%) in the plate-with-cage group. The Perfect-C, Zero-P, and plate-with-cage devices are effective for treating single-level cervical degenerative disc disease. However, the Perfect-C implant has many advantages over both the Zero-P implant and conventional plate-cage treatments. The Perfect-C implant was associated with shorter operation times and hospitalization durations, less blood loss, and lower subsidence rates compared with the Zero-P implant or the titanium plate with a PEEK cage.

Evaluation of anterior cervical reconstruction with titanium mesh cages versus nano-hydroxyapatite/polyamide66 cages after 1- or 2-level corpectomy for multilevel cervical spondylotic myelopathy: a retrospective study of 117 patients.

PubMed

Zhang, Yuan; Quan, Zhengxue; Zhao, Zenghui; Luo, Xiaoji; Tang, Ke; Li, Jie; Zhou, Xu; Jiang, Dianming

2014-01-01

To retrospectively compare the efficacy of the titanium mesh cage (TMC) and the nano-hydroxyapatite/polyamide66 cage (n-HA/PA66 cage) for 1- or 2-level anterior cervical corpectomy and fusion (ACCF) to treat multilevel cervical spondylotic myelopathy (MCSM). A total of 117 consecutive patients with MCSM who underwent 1- or 2-level ACCF using a TMC or an n-HA/PA66 cage were studied retrospectively at a mean follow-up of 45.28 ± 12.83 months. The patients were divided into four groups according to the level of corpectomy (1- or 2-level corpectomy) and cage type used (TMC or n-HA/PA66 cage). Clinical and radiological parameters were used to evaluate outcomes. At the one-year follow-up, the fusion rate in the n-HA/PA66 group was higher, albeit non-significantly, than that in the TMC group for both 1- and 2-level ACCF, but the fusion rates of the procedures were almost equal at the final follow-up. The incidence of cage subsidence at the final follow-up was significantly higher in the TMC group than in the n-HA/PA66 group for the 1-level ACCF (24% vs. 4%, p = 0.01), and the difference was greater for the 2-level ACCF between the TMC group and the n-HA/PA66 group (38% vs. 5%, p = 0.01). Meanwhile, a much greater loss of fused height was observed in the TMC group compared with the n-HA/PA66 group for both the 1- and 2-level ACCF. All four groups demonstrated increases in C2-C7 Cobb angle and JOA scores and decreases in VAS at the final follow-up compared with preoperative values. The lower incidence of cage subsidence, better maintenance of the height of the fused segment and similar excellent bony fusion indicate that the n-HA/PA66 cage may be a superior alternative to the TMC for cervical reconstruction after cervical corpectomy, in particular for 2-level ACCF.

Biomechanical analysis of an expandable lateral cage and a static transforaminal lumbar interbody fusion cage with posterior instrumentation in an in vitro spondylolisthesis model.

PubMed

Mantell, Matthew; Cyriac, Mathew; Haines, Colin M; Gudipally, Manasa; O'Brien, Joseph R

2016-01-01

Insufficient biomechanical data exist from comparisons of the stability of expandable lateral cages with that of static transforaminal lumbar interbody fusion (TLIF) cages. The purpose of this biomechanical study was to compare the relative rigidity of L4-5 expandable lateral interbody constructs with or without additive pedicle screw fixation with that of L4-5 static TLIF cages in a novel cadaveric spondylolisthesis model. Eight human cadaver spines were used in this study. A spondylolisthesis model was created at the L4-5 level by creating 2 injuries. First, in each cadaver, a nucleotomy from 2 channels through the anterior side was created. Second, the cartilage of the facet joint was burred down to create a gap of 4 mm. Light-emitting-diode tracking markers were placed at L-3, L-4, L-5, and S-1. Specimens were tested in the following scenarios: intact model, bilateral pedicle screws, expandable lateral 18-mm-wide cage (alone, with unilateral pedicle screws [UPSs], and with bilateral pedicle screws [BPSs]), expandable lateral 22-mm-wide cage (alone, with UPSs, and with BPSs), and TLIF (alone, with UPSs, and with BPSs). Four of the spines were tested with the expandable lateral cages (18-mm cage followed by the 22-mm cage), and 4 of the spines were tested with the TLIF construct. All these constructs were tested in flexion-extension, axial rotation, and lateral bending. The TLIF-alone construct was significantly less stable than the 18- and 22-mm-wide lateral lumbar interbody fusion (LLIF) constructs and the TLIF constructs with either UPSs or BPSs. The LLIF constructs alone were significantly less stable than the TLIF construct with BPSs. However, there was no significant difference between the 18-mm LLIF construct with UPSs and the TLIF construct with BPSs in any of the loading modes. Expandable lateral cages with UPSs provide stability equivalent to that of a TLIF construct with BPSs in a degenerative spondylolisthesis model.

Pop hole passages and welfare in furnished cages for laying hens.

PubMed

Wall, H; Tauson, R; Elwinger, K

2004-02-01

1. This study included two designs of furnished cages for 16 hens; H-cages divided into two apartments by a partition with pop holes in the middle of the cage, and fully open O-cages, without a partition. The hypothesis was that in this rather large group of birds the pop hole partition would benefit the birds by allowing them to avoid or escape from potential cannibals, feather-peckers or aggressive hens. All cages had two nests, two perches and one litter box. 2. A total of 10 cages (5 H and 5 O) were stocked with Lohmann Selected Leghorn (LSL) and 8 cages (4 H and 4 O) with Hy-Line W36. No birds were beak-trimmed. 3. Heterophil/lymphocyte (H/L) ratios, duration of tonic immobility (TI) and exterior appearance (scoring of plumage condition and wounds at comb or around cloaca) were used as indicators of well-being. Total mortality and deaths due to cannibalism were also recorded. 4. Visits to nests and passages through partition pop holes were studied in samples of 35 and 21 birds, respectively, using a technique based on passive integrated transponder (PIT) tags. 5. Cage design (H- vs O-cage) had no effect on the welfare traits chosen. 6. Hy-Line birds showed higher H/L ratios, longer duration of TI and better plumage condition than LSL birds. These differences are discussed in terms of stress thresholds and copying strategies. 7. On days when a hen made visits to nests, the visiting frequency was 1.4 and the total time in the nest was 41 min on average. Hens made use of the pop hole passages between 1 and 8 times per hen and day. 8. Overall low levels of aggression, lack of injuries or deaths due to cannibalism, and plumage condition indicating moderate feather pecking, together imply a low need to escape. The pop holes were used frequently and birds distributed well between compartments showing that the system worked well. However, at this group size there was no evidence in the measured traits that H-cages provided a better housing environment.

Sedation or Inhalant Anesthesia before Euthanasia with CO2 Does Not Reduce Behavioral or Physiologic Signs of Pain and Stress in Mice

PubMed Central

Valentine, Helen; Williams, Wendy O; Maurer, Kirk J

2012-01-01

CO2 administration is a common euthanasia method for research mice, yet questions remain regarding whether CO2 euthanasia is associated with pain and stress. Here we assessed whether premedication with acepromazine, midazolam, or anesthetic induction with isoflurane altered behavioral and physiologic parameters that may reflect pain or stress during CO2 euthanasia. Mice were assigned to 1 of 6 euthanasia groups: CO2 only at a flow rate of 1.2 L/min which displaces 20% of the cage volume per minute (V/min; control group); premedication with acepromazine (5 mg/kg), midazolam (5 mg/kg), or saline followed by 20% V/min CO2; induction with 5% isoflurane followed by greater than 100% V/min CO2 (>6L/min); and 100% V/min CO2 only (6 L/min). Measures included ultrasonic sound recordings, behavioral analysis of video recordings, plasma ACTH and corticosterone levels immediately after euthanasia, and quantification of c-fos from brain tissue. Compared with 20% V/min CO2 alone, premedication with acepromazine or midazolam did not significantly alter behavior but did induce significantly higher c-fos expression in the brain. Furthermore, the use of isoflurane induction prior to CO2 euthanasia significantly increased both behavioral and neuromolecular signs of stress. The data indicate that compared with other modalities, 20% V/min CO2 alone resulted in the least evidence of stress in mice and therefore was the most humane euthanasia method identified in the current study. PMID:22330868

Sedation or inhalant anesthesia before euthanasia with CO2 does not reduce behavioral or physiologic signs of pain and stress in mice.

PubMed

Valentine, Helen; Williams, Wendy O; Maurer, Kirk J

2012-01-01

CO(2) administration is a common euthanasia method for research mice, yet questions remain regarding whether CO(2) euthanasia is associated with pain and stress. Here we assessed whether premedication with acepromazine, midazolam, or anesthetic induction with isoflurane altered behavioral and physiologic parameters that may reflect pain or stress during CO(2) euthanasia. Mice were assigned to 1 of 6 euthanasia groups: CO(2) only at a flow rate of 1.2 L/min which displaces 20% of the cage volume per minute (V/min; control group); premedication with acepromazine (5 mg/kg), midazolam (5 mg/kg), or saline followed by 20% V/min CO(2); induction with 5% isoflurane followed by greater than 100% V/min CO(2) (>6L/min); and 100% V/min CO(2) only (6 L/min). Measures included ultrasonic sound recordings, behavioral analysis of video record- ings, plasma ACTH and corticosterone levels immediately after euthanasia, and quantification of c-fos from brain tissue. Compared with 20% V/min CO(2) alone, premedication with acepromazine or midazolam did not significantly alter behavior but did induce significantly higher c-fos expression in the brain. Furthermore, the use of isoflurane induction prior to CO(2) euthanasia significantly increased both behavioral and neuromolecular signs of stress. The data indicate that compared with other modalities, 20% V/min CO(2) alone resulted in the least evidence of stress in mice and therefore was the most humane euthanasia method identified in the current study.

Opinion of Belgian Egg Farmers on Hen Welfare and Its Relationship with Housing Type

PubMed Central

Stadig, Lisanne M.; Ampe, Bart A.; Van Gansbeke, Suzy; Van den Bogaert, Tom; D’Haenens, Evelien; Heerkens, Jasper L.T.; Tuyttens, Frank A.M.

2015-01-01

Simple Summary Until 2012, laying hens in the EU were often housed in conventional cages that offered limited space and few opportunities to perform highly motivated behaviors. Conventional cages are now banned in the EU in order to improve animal welfare. In this study, egg farmers were surveyed (winter 2013–2014) to assess whether they perceived any changes in animal welfare since changing housing systems, what role hen welfare played in choosing a new housing system, and which aspects of hen welfare they find most important. The data show that the answers differ depending on which housing system the farmers currently use and whether they had used conventional cages in the past. Abstract As of 2012, the EU has banned the use of conventional cages (CC) for laying hens, causing a shift in housing systems. This study’s aim was to gain insight into farmers’ opinions on hen health and welfare in their current housing systems. A survey was sent to 218 Belgian egg farmers, of which 127 (58.3%) responded, with 84 still active as egg farmer. Hen welfare tended to be less important in choosing the housing system for farmers with cage than with non-cage systems. Respondents currently using cage systems were more satisfied with hen health than respondents with non-cage systems. Reported mortality increased with farm size and was higher in furnished cages than in floor housing. Feather pecking, cannibalism, smothering and mortality were perceived to be higher in current housing systems than in CC, but only by respondents who shifted to non-cage systems from previously having had CC. Health- and production-related parameters were scored to be more important for hen welfare as compared to behavior-related parameters. Those without CC in the past rated factors relating to natural behavior to be more important for welfare than those with CC. This difference in opinion based on farmer backgrounds should be taken into account in future research. PMID:26703742

The effect of early life experience, environment, and genetic factors on spontaneous home-cage aggression-related wounding in male C57BL/6 mice.

PubMed

Gaskill, Brianna N; Stottler, Aurora M; Garner, Joseph P; Winnicker, Christina W; Mulder, Guy B; Pritchett-Corning, Kathleen R

2017-03-22

Aggression is a major welfare issue in mice, particularly when mice unfamiliar to each other are first placed in cages, as happens on receipt from a vendor, and following cage cleaning. Injuries from aggression are the second leading cause of unplanned euthanasia in mice, following ulcerative dermatitis. Commonly employed strategies for reducing aggression-related injury are largely anecdotal, and may even be counterproductive. Here we report a series of experiments testing potential explanations and interventions for post-shipping aggression-related injuries in C57BL/6 mice. First, we examined the effects of weaning: testing whether manipulating weaning age reduced aggression-related injuries, and if repeated mixing of weaned mice before shipping increased these injuries. Contrary to our predictions, repeated mixing did not increase post-shipping injurious aggression, and early weaning reduced aggression-related injuries. Second, we examined potential post-shipping interventions: testing whether lavender essential oil applied to the cage reduced aggression-related injuries, and whether a variety of enrichments decreased injurious aggression. Again, contrary to predictions, lavender increased wounding, and none of the enrichments reduced it. However, consistent with the effects of weaning age in the first experiment, cages with higher mean body weight showed elevated levels of aggression-related wounding. Finally, we tested whether C57BL/6 substrains and identification methods affected levels of intra-cage wounding from aggression. We found no effect of strain, but cages where mice were ear-notched for identification showed higher levels of wounding than cages where mice were tail-tattooed. Overall, these results emphasize the multifactorial nature of home-cage injurious aggression, and the importance of testing received wisdom when it comes to managing complex behavioral and welfare problems. In terms of practical recommendations to reduce aggressive wounding in the home cage, tail tattooing is recommended over ear notching and late weaning should be avoided.

Fractal dimension and fuzzy logic systems for broken rotor bar detection in induction motors at start-up and steady-state regimes

NASA Astrophysics Data System (ADS)

Amezquita-Sanchez, Juan P.; Valtierra-Rodriguez, Martin; Perez-Ramirez, Carlos A.; Camarena-Martinez, David; Garcia-Perez, Arturo; Romero-Troncoso, Rene J.

2017-07-01

Squirrel-cage induction motors (SCIMs) are key machines in many industrial applications. In this regard, the monitoring of their operating condition aiming at avoiding damage and reducing economical losses has become a demanding task for industry. In the literature, several techniques and methodologies to detect faults that affect the integrity and performance of SCIMs have been proposed. However, they have only been focused on analyzing either the start-up transient or the steady-state operation regimes, two common operating scenarios in real practice. In this work, a novel methodology for broken rotor bar (BRB) detection in SCIMs during both start-up and steady-state operation regimes is proposed. It consists of two main steps. In the first one, the analysis of three-axis vibration signals using fractal dimension (FD) theory is carried out. Since different FD-based algorithms can give different results, three algorithms named Katz’ FD, Higuchi’s FD, and box dimension, are tested. In the second step, a fuzzy logic system for each regime is presented for automatic diagnosis. To validate the proposal, a motor with different damage levels has been tested: one with a partially BRB, a second with one fully BRB, and the third with two BRBs. The obtained results demonstrate the proposed effectiveness.

Adaptive control schemes for improving dynamic performance of efficiency-optimized induction motor drives.

PubMed

Kumar, Navneet; Raj Chelliah, Thanga; Srivastava, S P

2015-07-01

Model Based Control (MBC) is one of the energy optimal controllers used in vector-controlled Induction Motor (IM) for controlling the excitation of motor in accordance with torque and speed. MBC offers energy conservation especially at part-load operation, but it creates ripples in torque and speed during load transition, leading to poor dynamic performance of the drive. This study investigates the opportunity for improving dynamic performance of a three-phase IM operating with MBC and proposes three control schemes: (i) MBC with a low pass filter (ii) torque producing current (iqs) injection in the output of speed controller (iii) Variable Structure Speed Controller (VSSC). The pre and post operation of MBC during load transition is also analyzed. The dynamic performance of a 1-hp, three-phase squirrel-cage IM with mine-hoist load diagram is tested. Test results are provided for the conventional field-oriented (constant flux) control and MBC (adjustable excitation) with proposed schemes. The effectiveness of proposed schemes is also illustrated for parametric variations. The test results and subsequent analysis confer that the motor dynamics improves significantly with all three proposed schemes in terms of overshoot/undershoot peak amplitude of torque and DC link power in addition to energy saving during load transitions. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Nonpolluting automobiles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoolboom, G.J.; Szabados, B.

The advantages/disadvantages of energy storage devices, which can provide nonpolluting automobile systems are discussed. Four types of storage devices are identified: electrochemical (batteries); hydrogen; electromechanical (flywheels); and molten salt heat storage. A high-speed flywheel with a small permanent magnet motor/generator has more advantages than any of the other systems and might become a real competitor to the internal combustion engine. A flywheel/motor/generator system for automobiles now becomes practical, because of the technological advances in materials, bearings and solid state control circuits. The motor of choice is the squirrel cage induction motor, specially designed for automobile applications. The preferred controller formore » the induction motor is a forced commutated cycloconverter, which transforms a variable voltage/variable frequency source into a controlled variable-voltage/variable-frequency supply. A modulation strategy of the cycloconverter elements is selected to maintain a unity input displacement factor (power factor) under all conditions of loads voltages and frequencies. The system is similar to that of the existing automobile, if only one motor is used: master controller-controller-motor-gears (fixed)-differential-wheels. In the case of two motors, the mechanical differential is replaced by an electric one: master controller-controller-motor-gears (fixed)-wheel. A four-wheel drive vehicle is obtained when four motors with their own controllers are used. 24 refs.« less

Effect of acclimation to caging on nephrotoxic response of rats to uranium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Damon, E.G.; Eidson, A.F.; Hobbs, C.H.

1986-02-01

Animal studies of the toxicity and metabolism of radionuclides and chemicals often require housing of rats in metabolism cages for excreta collection. Response of rats to toxic substances may be affected by environmental factors such as the type of cage used. Dose-response studies were conducted to assess the effects of two types of cages on the nephrotoxic response of rats to uranium from implanted refined uranium ore (yellowcake). The LD50/21 days was 6 mg of uranium ore per kilogram body weight (6 mg U/kg). The 95% confidence limit (C.L.) was 3-8 mg U/kg for rats housed in metabolism cages beginningmore » on the day of implantation (naive rats). However, for rats housed in metabolism cages for 21 days before implantation (acclimated rats) the LD50/21 days was 360 mg U/kg (95% C.L. = 220-650 mg U/kg), which was the same value obtained for rats housed continuously in polycarbonate cages. This significant difference (P less than 0.01) in response of naive rats compared to response of acclimated rats appeared related to a significantly lower water consumption by the naive rats.« less

Care of captive woodcocks

USGS Publications Warehouse

Stickel, William H.; Sheldon, William G.; Stickel, Lucille F.

1965-01-01

Numbers of American woodcocks (Philohela minor) were held in cages for experimental work lasting several months. Injuries caused by birds attempting to flush were greatly reduced by clipping feathers from one wing, by making cage walls opaque, and by using high cages or false ceilings of fabric. Size of cage was found not to be important, to judge from weight changes, so long as ample food was unmistakably available. Birds were kept in both large and small cages without social conflicts. Cages on the ground proved too unsanitary for long-term use; small steel cages with removable floors were practical but did not solve the sanitation problem. Living earthworms (Lumbricus terrestris) were provided daily in amounts roughly equal to weights of birds. Birds gained on this food when worms were offered in suitable ways. The feeding tray recommended is a large roasting pan with a snap-on metal rim that retards loss of worms. Trays contained moist peat in which birds probed for worms. Two efforts to keep woodcocks on a diet of red worms (Eisenia foetide) were unsuccessful; use of this worm was considered responsible. Woodcocks were handled and transported for short periods with least injury to them when they were rolled individually in soft bags.

The effect of host relaxation and dynamics on guest molecule dynamics in H2/tetrahydrofuranhydrate.

PubMed

Peterson, Vanessa K; Shoko, Elvis; Kearley, Gordon J

2011-01-01

We use ab initio molecular dynamics simulations to obtain classically the effects of H2O cage motions on the potential-energy surface (PES) of encapsulated H2 in the H2/tetrahydrofuran-hydrate system. The significant differences between the PES for the H2 in rigid and flexible cages that we find will influence calculation of the quantum dynamics of the H2. Part of these differences arises from the relaxation of the H2O cage around the classical H2, with a second part arising from the coupling of both translational and rotational motions of H2 with the H20 cage. We find that isotopic substitution of 2H for 1H of the H2O cage affects the coupling, which has implications for experiments that require the use of 2H2O, including inelastic neutron scattering that uses 2H2O cages in order to focus on the H2 guest dynamics. Overall, this work emphasizes the importance of taking into account cage dynamics in any approach used to understand the dynamics of H2 guests in porous framework materials.

Evaluation of cage designs and feeding regimes for honey bee (Hymenoptera: Apidae) laboratory experiments.

PubMed

Huang, Shao Kang; Csaki, Tamas; Doublet, Vincent; Dussaubat, Claudia; Evans, Jay D; Gajda, Anna M; Gregorc, Alex; Hamilton, Michele C; Kamler, Martin; Lecocq, Antoine; Muz, Mustafa N; Neumann, Peter; Ozkirim, Asli; Schiesser, Aygün; Sohr, Alex R; Tanner, Gina; Tozkar, Cansu Ozge; Williams, Geoffrey R; Wu, Lyman; Zheng, Huoqing; Chen, Yan Ping

2014-02-01

The aim of this study was to improve cage systems for maintaining adult honey bee (Apis mellifera L.) workers under in vitro laboratory conditions. To achieve this goal, we experimentally evaluated the impact of different cages, developed by scientists of the international research network COLOSS (Prevention of honey bee COlony LOSSes), on the physiology and survival of honey bees. We identified three cages that promoted good survival of honey bees. The bees from cages that exhibited greater survival had relatively lower titers of deformed wing virus, suggesting that deformed wing virus is a significant marker reflecting stress level and health status of the host. We also determined that a leak- and drip-proof feeder was an integral part of a cage system and a feeder modified from a 20-ml plastic syringe displayed the best result in providing steady food supply to bees. Finally, we also demonstrated that the addition of protein to the bees' diet could significantly increase the level ofvitellogenin gene expression and improve bees' survival. This international collaborative study represents a critical step toward improvement of cage designs and feeding regimes for honey bee laboratory experiments.

Caged Protein Prenyltransferase Substrates: Tools for Understanding Protein Prenylation

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeGraw, Amanda J.; Hast, Michael A.; Xu, Juhua

Originally designed to block the prenylation of oncogenic Ras, inhibitors of protein farnesyltransferase currently in preclinical and clinical trials are showing efficacy in cancers with normal Ras. Blocking protein prenylation has also shown promise in the treatment of malaria, Chagas disease and progeria syndrome. A better understanding of the mechanism, targets and in vivo consequences of protein prenylation are needed to elucidate the mode of action of current PFTase (Protein Farnesyltransferase) inhibitors and to create more potent and selective compounds. Caged enzyme substrates are useful tools for understanding enzyme mechanism and biological function. Reported here is the synthesis and characterizationmore » of caged substrates of PFTase. The caged isoprenoid diphosphates are poor substrates prior to photolysis. The caged CAAX peptide is a true catalytically caged substrate of PFTase in that it is to not a substrate, yet is able to bind to the enzyme as established by inhibition studies and X-ray crystallography. Irradiation of the caged molecules with 350 nm light readily releases their cognate substrate and their photolysis products are benign. These properties highlight the utility of those analogs towards a variety of in vitro and in vivo applications.« less

Effect of acclimation to caging on nephrotoxic response of rats to uranium.

PubMed

Damon, E G; Eidson, A F; Hobbs, C H; Hahn, F F

1986-02-01

Animal studies of the toxicity and metabolism of radionuclides and chemicals often require housing of rats in metabolism cages for excreta collection. Response of rats to toxic substances may be affected by environmental factors such as the type of cage used. Dose-response studies were conducted to assess the effects of two types of cages on the nephrotoxic response of rats to uranium from implanted refined uranium ore (yellowcake). The LD50/21 days was 6 mg of uranium ore per kilogram body weight (6 mg U/kg). The 95% confidence limit (C.L.) was 3-8 mg U/kg for rats housed in metabolism cages beginning on the day of implantation (naive rats). However, for rats housed in metabolism cages for 21 days before implantation (acclimated rats) the LD50/21 days was 360 mg U/kg (95% C.L. = 220-650 mg U/kg), which was the same value obtained for rats housed continuously in polycarbonate cages. This significant difference (P less than 0.01) in response of naive rats compared to response of acclimated rats appeared related to a significantly lower water consumption by the naive rats.

Alternating-Current Motor Drive for Electric Vehicles

NASA Technical Reports Server (NTRS)

Krauthamer, S.; Rippel, W. E.

1982-01-01

New electric drive controls speed of a polyphase as motor by varying frequency of inverter output. Closed-loop current-sensing circuit automatically adjusts frequency of voltage-controlled oscillator that controls inverter frequency, to limit starting and accelerating surges. Efficient inverter and ac motor would give electric vehicles extra miles per battery charge.

A polyphasic approach for characterization of a collection of cereal isolates of the Fusarium incarnatum-equiseti species complex

USDA-ARS?s Scientific Manuscript database

DNA-based phylogenetic analyses have resolved the fungal genus Fusarium into multiple species complexes. The F. incarnatum-equiseti species complex (FIESC) includes fusaria associated with several diseases of agriculturally important crops, including cereals. Although members of FIESC are considered...

Description of Campylobacter fetus subsp. testudinum subsp. nov., isolated from humans and reptiles

USDA-ARS?s Scientific Manuscript database

A polyphasic study was undertaken to determine the taxonomic position of 13 Campylobacter fetus-like isolates from humans (n=8) and reptiles (n=5). Phenotypic characterization, Genusgenus-specific and sap insertion-PCR initially identified all human isolates as type A Campylobacter fetus. Phylogenet...

COATING ALTERNATIVES GUIDE (CAGE) USER'S GUIDE

EPA Science Inventory

The guide provides instructions for using the Coating Alternatives GuidE (CAGE) software program, version 1.0. It assumes that the user is familiar with the fundamentals of operating an IBM-compatible personal computer (PC) under the Microsoft disk operating system (MS-DOS). CAGE...

A fluorescent organic cage for picric acid detection.

PubMed

Acharyya, Koushik; Mukherjee, Partha Sarathi

2014-12-25

Dynamic covalent imine chemistry has been utilized to synthesize a fluorescent [3+2] self-assembled nanoscopic organic cage. The fluorescent nature of the reduced analogue of the cage was further exploited for the highly selective detection of the explosive picric acid (PA).

Carbon-Phenolic Cages for High-Speed Bearings. Part II - Bearing Evaluation with a Multiply-Alkylated Cyclopentane (MAC) Lubricant

DTIC Science & Technology

2003-01-01

program manager for the overall effort. The carbon -phenolic cages were fabricated under the direction of Mr. Wei Shih of Allcomp Inc ., City of...friction. The early carbon -phenolic cages were hand wrapped by Allcomp . Since that time, Allcomp has added a wrapping machine that uses uniform tension...AFRL-PR-WP-TR-2003-2032 CARBON -PHENOLIC CAGES FOR HIGH-SPEED BEARINGS Part II - Bearing Evaluation with a Multiply- Alkylated Cyclopentane (MAC

Extremely Low Frequency (ELF) Vertical Electric Field Exposure of Rats: Irradiation Facility

DTIC Science & Technology

1977-05-01

altered inside an animal cage even with wet or dry litter and full food and water containers. Rats weighing approximately 300 g in adjacent cages caused...with guard circuit Field inside empty cage Field inside complete cage ( litter (wet or dry) + food + water) Field variations caused by 300 g rat...blanket 250 Iron 60 Broiler 130 Hair dryer 40 Vaporizer 40 Refrigerator 60 Color TV 30 Stereo 90 Coffee pot 30 Vacuum cleaner 16 Clock radio

Exterior egg quality as affected by enrichment resources layout in furnished laying-hen cages.

PubMed

Li, Xiang; Chen, Donghua; Meng, Fanyu; Su, Yingying; Wang, Lisha; Zhang, Runxiang; Li, Jianhong; Bao, Jun

2017-10-01

This study aimed to investigate the effects of enrichment resources (a perch, dustbath, and nest) layout in furnished laying-hen cages (FC) on exterior quality of eggs. One hundred and sixty-eight (168) Hy-Line Brown laying hens at 16 weeks of age were randomly distributed to four treatments: small furnished cages (SFC), medium furnished cages type I (MFC-I), medium furnished cages type II (MFC-II), and medium furnished cages type III (MFC-III). Each treatment had 4 replicates or cages with 6 hens for SFC (24 birds for each SFC) and 12 hen/cage for MFC-I, -II, and -III (48 birds for each MFC-I, -II and -III). Following a 2-week acclimation, data collection started at 18 weeks of age and continued till 52 weeks of age. Dirtiness of egg surface or cracked shell as indicators of the exterior egg quality were recorded each week. The results showed that the proportion of cracked or dirty eggs was significantly affected by the FC type (p<0.01) in that the highest proportion of cracked or dirty eggs was found in MFC-I and the lowest proportion of dirty eggs in SFC. The results of this showed that furnished cage types affected both dirty eggs and cracked eggs (p<0.01). The results also indicated that not nest but dustbath lead to more dirty eggs. Only MFC-I had higher dirty eggs at nest than other FC (p< 0.01). The results of dirty eggs in MFC-I and MFC-II compared with SFC and MFC-III seemed suggest that a low position of dustbath led to more dirty eggs. SFC design affected exterior egg quality and the low position of dustbath in FC resulted in higher proportion of dirty eggs.

Effect of a commercial housing system on egg quality during extended storage.

PubMed

Jones, D R; Karcher, D M; Abdo, Z

2014-05-01

Egg producers in the United States are utilizing a variety of commercial egg production systems to provide consumer choice and meet legislative requirements. Consumer egg grades in the United States were developed for conventional cage production, and it is unclear what effect alternative production systems might have on egg quality during retail and consumer home storage. The current study was undertaken to determine what changes in egg quality characteristics occur during extended cold storage for commercially produced conventional cage, enriched colony cage, and cage-free aviary eggs. During 12 wk of cold storage, egg weight, albumen height, Haugh unit, static compression shell strength, vitelline membrane strength and deformation, yolk index, shell dynamic stiffness, and whole egg total solids were monitored. Overall, aviary and enriched eggs were significantly (P < 0.05) heavier than conventional cage. Albumen height and Haugh unit (P < 0.05) were significantly greater for conventional cage than enriched eggs. Static compression shell strength was greatest (P < 0.05) for enriched eggs compared with aviary. No overall housing system effects for yolk measurements, shell dynamic stiffness, or whole egg total solids were observed. Albumen height, Haugh unit, and yolk quality measurements were all greatest at 0 and lowest at 12 wk of storage (P < 0.05). The rate of quality change among the housing systems for each measured attribute at 4, 6, and 12 wk was determined. Other than differences in the change of egg weight at 4 wk, no significant differences in the rate of quality decline were found among the housing systems. The results of the current study indicate that current US egg quality standards should effectively define quality for commercially produced conventional cage, enriched colony cage, and cage-free aviary eggs.

Mosquito density, biting rate and cage size effects on repellent tests.

PubMed

Barnard, D R; Posey, K H; Smith, D; Schreck, C E

1998-01-01

Mosquito biting rates and the mean duration of protection (in hours) from bites (MDPB) of Aedes aegypti and Anopheles quadrimaculatus, using the repellent 'deet' (N,N-diethyl-3-methylbenzamide) on a 50 cm2 area of healthy human skin, were observed in small (27 l), medium (approximately 65 l) and large (125 l) cages containing low, medium or high densities of mosquitoes: respectively, 640, 128 or 49 cm3 of cage volume per female. At the initial treatment rate of approximately 0.4 microliter/cm2 (1 ml of 25% deet in ethanol on 650 cm2 of skin), the MDPB for deet against Ae. aegypti ranged from 4.5 to 6.5 h and was significantly less (5.0 +/- 0.8 h) in large cages compared with medium (6.2 +/- 0.9 h) and small (6.2 +/- 0.8 h) cages, regardless of the density. Against An. quadrimaculatus the MDPB for deet 0.4 microliter/cm2 was 1.5-8.0 h, less in small (3.7 +/- 2.3 h) and large (2.2 +/- 1.1 h) cages at medium (3.7 +/- 2.3 h) and high (2.5 +/- 1.7 h) mosquito densities, and was longest in medium cages (6.2 +/- 2.6 h) at low mosquito densities (5.8 +/- 2.8 h). With equinoxial photoperiodicity (light on 06.00-18.00 hours) the biting rate was influenced by the time of observation (08.00, 12.00, 16.00 hours) for Ae. aegypti but not for An. quadrimaculatus. For both species, the biting rate was inversely proportional to mosquito density and the MDPB. The shortest MDPBs were obtained in large cages with high densities of mosquitoes and longest protection times occurred in medium sized cages with low mosquito densities.

Self-Assembled Pyridine-Dipyrrolate Cages.

PubMed

Zhang, Huacheng; Lee, Juhoon; Lammer, Aaron D; Chi, Xiaodong; Brewster, James T; Lynch, Vincent M; Li, Hao; Zhang, Zhan; Sessler, Jonathan L

2016-04-06

An inherently nonlinear pyridine dipyrrolate ligand, namely 2,6-bis(3,4-diethyl-5-carboxy-1H-pyrrol-2yl)pyridine (compound 1), is able to distinguish between different zinc(II) cation sources, namely Zn(acac)2 and Zn(OAc)2, respectively. This differentiation is manifest both in terms of the observed fluorescent behavior in mixed organic media and the reaction chemistry. Treatment of 1 with Zn(acac)2 gives rise to a cage dimer, cage-1, wherein two molecules of compound 1 act as double bridging units to connect two individual cage subunits. As inferred from X-ray crystallographic studies, this cage system consists of discrete zinc dimers with hydroxide bridges that, with the assistance of bound DMF solvent molecules, serve to fix the geometry and orientation of the pyridine dipyrrolate building blocks. When a different zinc source, Zn(OAc)2, is used to carry out an ostensibly similar complexation reaction with compound 1, an acetate-bridged 1D abacus-like cage polymer is obtained as inferred from X-ray diffraction analysis. This extended solid state structure, cage-2, contains individual zinc dimer cage submits and appears stabilized by solvent molecules (DMF) and the counteranion (acetate). Rod-like assemblies are also observed by DLS and SEM. This construct, in contrast to cage-1, proved fluorescent in mixed organic media. The structure of the ligand itself (i.e., in the absence of Zn(II)) was confirmed by X-ray crystallographic analysis and was found to assemble into a supramolecular polymer. Conversion to a dimer form was seen upon the addition of TBAOAc. On the basis of the metric parameters, the structures seen in the solid state are stabilized via hydrogen bonding interactions involving solvent molecules.

Screening of alcohol use disorders in psychiatric outpatients: influence of gender, age, and psychiatric diagnosis.

PubMed

Sánchez Autet, Mónica; Garriga, Marina; Zamora, Francisco Javier; González, Idilio; Usall, Judith; Tolosa, Leticia; Benítez, Concepción; Puertas, Raquel; Arranz, Belén

2017-07-14

Alcohol use disorders (AUD) are 2 times higher among psychiatric patients than in the general population. The under-recognition of this dual diagnosis can entail several negative outcomes. Early assessment with a screening tool like the CAGE questionnaire could be an opportunity to improve patients' prognoses. The objective of this study is to assess AUD risk in an outpatient psychiatric sample with a modified CAGE, considering the influence of age, gender and clinical psychiatric diagnosis. An observational, multicentric, descriptive study was carried out. The 4-item CAGE scale, camouflaged in a healthy lifestyle questionnaire, was implemented, using a cut-off point of one. 559 outpatients were assessed. 54% were female and the average age was 50.07 years. 182 patients presented a CAGE score ≥1 (45.1% of men and 21.9% of women). Gender was the strongest predictor of a positive result in CAGE, as men were 3.03 times more likely to score ≥1 on the CAGE questionnaire (p < .001, 95% CI: 0.22-0.49). Patients with bipolar and personality disorders had the highest rates of CAGE scores ≥1 (45.2 and 44.9%, respectively), with a significant association between diagnosis and a positive score (p = .002). Patients above 60 years were 2.5 times less likely to score ≥1 on the CAGE (p = .017, 95% CI: 0.19-0.85). Specific screening questionnaires, like the CAGE scale, can be an easy and useful tool in the assessment of AUD risk in psychiatric outpatients. Male patients with a bipolar or personality disorder present a higher risk of AUD.

-A practical application of reduced-copper antifouling paint in marine biological research.

PubMed

Jerabek, Andrea S; Wall, Kara R; Stallings, Christopher D

2016-01-01

Biofouling of experimental cages and other field apparatuses can be problematic for scientists and has traditionally been addressed using frequent manual removal (e.g., scraping, scrubbing). Recent environmental restrictions and legislative changes have driven the development of less hazardous antifouling products, making antifouling paint a potential alternative option to manual removal. Consequently, the viability of using these newly developed products as a replacement for the manual cleaning of exclusion cages was experimentally investigated. There were six treatments tested, comprising three with settlement tiles in experimental cages coated with antifouling paint, two with settlement tiles in unpainted experimental cages, and one cage-free suspended tile. The three antifouling treatments comprised two reduced-copper paints (21% Cu2O and 40% Cu2O) and one copper-free, Econea (™)-based paint (labeled "ecofriendly"). Antifouling paints were assessed for performance of preventing fouling of the cages and whether they elicited local effects on settlement tiles contained within them. All three paints performed well to reduce fouling of the cages during the initial six weeks of the experiment, but the efficacy of "ecofriendly" paint began to decrease during an extended deployment that lasted 14 weeks. The macro-community composition, biomass, and percent cover of settled organism on tiles within cages treated with copper-based paints (21% and 40% concentrations) were indistinguishable from tiles within the manually scrubbed cages. In contrast, settlement to tiles from the "ecofriendly" treatment was different in composition of macro-community and lower in biomass, suggesting the presence of local effects and therefore rendering it unsuitable for use in settlement experiments. The results of this study suggest that reduced-copper paints have the potential to serve as an alternative to manual maintenance, which may be useful for deployments in locations that are difficult to access on a frequent schedule.

Anterior debridement and fusion followed by posterior pedicle screw fixation in pyogenic spondylodiscitis: autologous iliac bone strut versus cage.

PubMed

Pee, Yong Hun; Park, Jong Dae; Choi, Young-Geun; Lee, Sang-Ho

2008-05-01

An anterior approach for debridement and fusion with autologous bone graft has been recommended as the gold standard for surgical treatment of pyogenic spondylodiscitis. The use of anterior foreign body implants at the site of active infection is still a challenging procedure for spine surgeons. Several authors have recently introduced anterior grafting with titanium mesh cages instead of autologous bone strut in the treatment of spondylodiscitis. The authors present their experience of anterior fusion with 3 types of cages followed by posterior pedicle screw fixation. They also compare their results with the use of autologous iliac bone strut. The authors retrospectively reviewed the cases of 60 patients with pyogenic spondylodiscitis treated by anterior debridement between January 2003 and April 2005. Fusion using either cages or iliac bone struts was performed during the same course of anesthesia followed by posterior fixation. Twenty-three patients underwent fusion with autologous iliac bone strut, and 37 patients underwent fusion with 1 of the 3 types of cages. The infections resolved in all patients, as noted by normalization of their erythrocyte sedimentation rates and C-reactive protein levels. Patients in both groups were evaluated in terms of their preoperative and postoperative clinical and imaging findings. Single-stage anterior debridement and cage fusion followed by posterior pedicle screw fixation can be effective in the treatment of pyogenic spondylodiscitis. There was no difference in clinical and imaging outcomes between the strut group and cage group except for the subsidence rate. The subsidence rate was higher in the strut group than in the cage group. The duration until subsidence was also shorter in the strut group than in the cage group.

From Coordination Cages to a Stable Crystalline Porous Hydrogen-Bonded Framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ju, Zhanfeng; Liu, Guoliang; Chen, Yu-Sheng

2017-03-20

A stable framework has been constructed through multiple charge-assisted H-bonds between cationic coordination cages and chloride ions. The framework maintained its original structure upon desolvation, which has been established by single-crystal structure analysis. This is the first fully characterized stable porous framework based on coordination cages after desolvation, with a moderately high Brunauer–Emmett–Teller (BET) surface area of 1201 m2 g-1. This work will not only give a light to construct stable porous frameworks based on coordination cages and thus broaden their applications, but will also provide a new avenue to the assembly of other porous materials such as porous organicmore » cages and hydrogen-bonded organic frameworks (HOFs) through non covalent bonds.« less

More vertical etch profile using a Faraday cage in plasma etching

NASA Astrophysics Data System (ADS)

Cho, Byeong-Ok; Hwang, Sung-Wook; Ryu, Jung-Hyun; Moon, Sang Heup

1999-05-01

Scanning electron microscope images of sidewalls obtained by plasma etching of an SiO2 film with and without a Faraday cage have been compared. When the substrate film is etched in the Faraday cage, faceting is effectively suppressed and the etch profile becomes more vertical regardless of the process conditions. This is because the electric potential in the cage is nearly uniform and therefore distortion of the electric field at the convex corner of a microfeature is prevented. The most vertical etch profile is obtained when the cage is used in fluorocarbon plasmas, where faceting is further suppressed due to the decrease in the chemical sputtering yield and the increase in the radical/ion flux on the substrate.

Open-cage fullerene-like graphitic carbons as catalysts for oxidative dehydrogenation of isobutane.

PubMed

Liang, Chengdu; Xie, Hong; Schwartz, Viviane; Howe, Jane; Dai, Sheng; Overbury, Steven H

2009-06-10

We report herein a facile synthesis of fullerene-like cages, which can be opened and closed through simple thermal treatments. A glassy carbon with enclosed fullerene-like cages of 2-3 nm was synthesized through a soft-template approach that created open mesopores of 7 nm. The open mesopores provided access to the fullerene-like cages, which were opened and closed through heat treatments in air and inert gas at various temperatures. Catalytic measurements showed that the open cages displayed strikingly higher activity for the oxidative dehydrogenation of isobutane in comparison to the closed ones. We anticipate that this synthesis approach could unravel an avenue for pursuing fundamental understanding of the unique catalytic properties of graphitic carbon nanostructures.

Canine tooth wear in captive little brown bats

USGS Publications Warehouse

Clark, Donald R.

1980-01-01

Upper canine teeth of little brown bats Myotis lucifugus lucifugus held in stainless steel wire mesh cages underwent severe wear which exceeded that observed previously in caged big brown bats, Eptesicus fuscus fuscus. This suggests a relationship between amount of wear and size of the caged bats with damage increasing as size decreases. Rapid wear of canine teeth by little brown bats resembled that observed in big brown bats in that it was limited to the first 2 weeks of captivity. This result indicates a universal interval for acclimation to cage conditions among vespertilionid bats. Dietary toxicants DDE and PCB did not affect the extent of wear. If bats are to be released to the wild, confinement in wire mesh cages should be avoided.

The Cage-Busting Teacher

ERIC Educational Resources Information Center

Hess, Frederick M.

2015-01-01

"The Cage-Busting Teacher" adopts the logic of "Cage-Busting Leadership" and applies it to the unique challenges and opportunities of classroom teachers. Detailed, accessible, and thoroughly engaging, it uncovers the many ways in which teachers can break out of familiar constraints in order to influence school and classroom…

The structuring process of the macroparasite community of an experimental population of cichlasoma urophthalmus through time

PubMed

Vidal-Martinez; Kennedy; Aguirre-Macedo

1998-09-01

The structuring process of the macroparasite community of caged Cichlasoma urophthalmus was studied over time using sentinel fish. Three thousand uninfected cichlids were stocked in floating cages introduced into a quarry in which a wild population of the same species was present. Caged and wild cichlids were sampled monthly over 6 and 7 months, respectively. Seventeen macroparasite species were found in the wild C. urophthalmus population, ten of which were detected in the caged population after 6 months. Early infections were by those species that were more frequent and abundant in the wild population, while helminths with a low prevalence and abundance in the wild appeared later in the caged fish population. The results suggested that the structuring process of the macroparasite community of caged C. urophthalmus followed a predictable pattern, in which those species that were most frequent and abundant in the wild were the first to establish in sentinel fish.

Revision of Ilyphagus Chamberlin, 1919 (Polychaeta, Flabelligeridae)

PubMed Central

Salazar-Vallejo, Sergio I.

2012-01-01

Abstract Ilyphagus Chamberlin, 1919 includes abyssal, fragile benthic species. Most species have large cephalic cages but chaetae are brittle and easily lost which may explain why the original definition included species with a cephalic cage or without it. The type species, Ilyphagus bythincola Chamberlin, 1919, together with another species (Ilyphagus pluto Chamberlin, 1919) were described as lacking a cephalic cage whereas a third species (Ilyphagus ascendens Chamberlin, 1919) was described with one. To clarify this situation, all available type and non-type materials were studied. Ilyphagus is redefined to include species with digitiform bodies, abundant filiform papillae and a thin body wall; their neurochaetae are thick, anchylosed aristate spines, and all species have a cephalic cage (in the type species the presence of a cage is inferred from the remaining chaetal scars). Ilyphagus pluto, which also lacks a a cephalic cage is determined here to be a holothurian. The redefined genus contains Ilyphagus bythincola (incl. Ilyphagus ascendens), Ilyphagus coronatus Monro, 1939, Ilyphagus hirsutus Monro, 1937, and Ilyphagus wyvillei (McIntosh, 1885). PMID:22639528

Usefulness of the "CAGE" in Malaysia.

PubMed

Indran, S K

1995-04-01

This study examines the usefulness of the "CAGE", (which is an acronym for "cut down", "annoyed", "guilty" and "eye-opener"), a 4-question screening test to identify excessive drinkers among Malaysian inpatients. The CAGE questionnaire after translation and back translation was administered to all inpatients in the General Hospital, Kuala Lumpur. The author interviewed 'blindly' all who score positive on the CAGE score and 10% of all negatives using the DSM III interview schedule for alcohol abuse dependence. The results show that the CAGE performs best at a cut-off point of 2 and above, with a sensitivity of 92%, specificity of 62%, positive predictive values of 38% and Kappa (K) of 0.37 with a DSM III R diagnosis for alcohol abuse/dependence. The poor agreement with a DSM III diagnosis indicates that the CAGE is not useful in the Malaysian population. Reasons suggested for this are: cultural factors in the Malaysian population resulting in the overrating of the question of 'guilt' by Muslims and translations into the local languages which are only the closest approximations.

A geometric constraint, the head-to-tail exclusion rule, may be the basis for the isolated-pentagon rule in fullerenes with more than 60 vertices

PubMed Central

Schein, Stan; Friedrich, Tara

2008-01-01

Carbon atoms self-assemble into the famous soccer-ball shaped Buckminsterfullerene (C60), the smallest fullerene cage that obeys the isolated-pentagon rule (IPR). Carbon atoms self-assemble into larger (n > 60 vertices) empty cages as well—but only the few that obey the IPR—and at least 1 small fullerene (n ≤ 60) with adjacent pentagons. Clathrin protein also self-assembles into small fullerene cages with adjacent pentagons, but just a few of those. We asked why carbon atoms and clathrin proteins self-assembled into just those IPR and small cage isomers. In answer, we described a geometric constraint—the head-to-tail exclusion rule—that permits self-assembly of just the following fullerene cages: among the 5,769 possible small cages (n ≤ 60 vertices) with adjacent pentagons, only 15; the soccer ball (n = 60); and among the 216,739 large cages with 60 < n ≤ 84 vertices, only the 50 IPR ones. The last finding was a complete surprise. Here, by showing that the largest permitted fullerene with adjacent pentagons is one with 60 vertices and a ring of interleaved hexagons and pentagon pairs, we prove that for all n > 60, the head-to-tail exclusion rule permits only (and all) fullerene cages and nanotubes that obey the IPR. We therefore suggest that self-assembly that obeys the IPR may be explained by the head-to-tail exclusion rule, a geometric constraint. PMID:19050075

COATING ALTERNATIVES GUIDE (CAGE) USER'S GUIDE (EPA/600/R-01/030)

EPA Science Inventory

The guide provides instructions for using the Coating Alternatives GuidE (CAGE) software program, version 1.0. It assumes that the user is familiar with the fundamentals of operating an IBM-compatible personal computer (PC) under the Microsoft disk operating system (MS-DOS). CAGE...

Faraday Cage Protects Against Lightning

NASA Technical Reports Server (NTRS)

Jafferis, W.; Hasbrouck, R. T.; Johnson, J. P.

1992-01-01

Faraday cage protects electronic and electronically actuated equipment from lightning. Follows standard lightning-protection principles. Whether lightning strikes cage or cables running to equipment, current canceled or minimized in equipment and discharged into ground. Applicable to protection of scientific instruments, computers, radio transmitters and receivers, and power-switching equipment.

Food consumption and food exchange of caged honey bees using a radioactive labelled sugar solution

PubMed Central

Libor, Anika; Kupelwieser, Vera; Crailsheim, Karl

2017-01-01

We measured the distribution of sugar solution within groups of caged honey bees (Apis mellifera) under standard in vitro laboratory conditions using 14C polyethylene glycol as a radioactive marker to analyze ingestion by individual bees after group feeding. We studied the impact of different experimental setups by varying the number of bees, age of bees, origin of bees, duration of experiment, the amount of available diet, and the influence of the neurotoxic pesticide imidacloprid in the diet on the feeding and food sharing behavior (trophallaxis). Sugar solution was non-uniformly distributed in bees in 36 out of 135 cages. As a measure of the extent to which the sugar diet was equally distributed between caged bees, we calculated the (inner 80%) intake ratio by dividing the intake of the 90th percentile bee by the intake of the 10th percentile bee. This intake ratio ranged from 1.3 to 94.8 in 133 individual cages, further supporting a non-uniform distribution of food among caged bees. We can expect a cage with 10 or 30 bees containing one bee that ingests, on average, the 8.8-fold of the bee in the same cage ingesting the smallest quantity of food. Inner 80% intake ratios were lower in experiments with a permanent or chronic offering of labelled sugar solution compared to temporary or acute feedings. After pooling the data of replicates to achieve a higher statistical power we compared different experimental setups. We found that uniform food distribution is best approached with 10 newly emerged bees per cage, which originate from a brood comb from a single colony. We also investigated the trophallaxis between caged honey bees which originally consumed the diet and newly added bees. Color marked bees were starved and added to the cages in a ratio of 10:5 or 20:20 after the initial set of bees consumed all the labelled sugar solution. The distribution of the labelled sugar solution by trophallaxis within 48 hours to added bees was 25% (10:5) or 45% (20:20) of the initial sugar solution. Imidacloprid at its median lethal dose (LD50) in the sugar solution reduced this post-feeding food transmission to 27% (20:20). Our results show that differences in food intake exist within caged bees that may lead to differential exposure that can influence the interpretation of toxicity tests. PMID:28355267

Food consumption and food exchange of caged honey bees using a radioactive labelled sugar solution.

PubMed

Brodschneider, Robert; Libor, Anika; Kupelwieser, Vera; Crailsheim, Karl

2017-01-01

We measured the distribution of sugar solution within groups of caged honey bees (Apis mellifera) under standard in vitro laboratory conditions using 14C polyethylene glycol as a radioactive marker to analyze ingestion by individual bees after group feeding. We studied the impact of different experimental setups by varying the number of bees, age of bees, origin of bees, duration of experiment, the amount of available diet, and the influence of the neurotoxic pesticide imidacloprid in the diet on the feeding and food sharing behavior (trophallaxis). Sugar solution was non-uniformly distributed in bees in 36 out of 135 cages. As a measure of the extent to which the sugar diet was equally distributed between caged bees, we calculated the (inner 80%) intake ratio by dividing the intake of the 90th percentile bee by the intake of the 10th percentile bee. This intake ratio ranged from 1.3 to 94.8 in 133 individual cages, further supporting a non-uniform distribution of food among caged bees. We can expect a cage with 10 or 30 bees containing one bee that ingests, on average, the 8.8-fold of the bee in the same cage ingesting the smallest quantity of food. Inner 80% intake ratios were lower in experiments with a permanent or chronic offering of labelled sugar solution compared to temporary or acute feedings. After pooling the data of replicates to achieve a higher statistical power we compared different experimental setups. We found that uniform food distribution is best approached with 10 newly emerged bees per cage, which originate from a brood comb from a single colony. We also investigated the trophallaxis between caged honey bees which originally consumed the diet and newly added bees. Color marked bees were starved and added to the cages in a ratio of 10:5 or 20:20 after the initial set of bees consumed all the labelled sugar solution. The distribution of the labelled sugar solution by trophallaxis within 48 hours to added bees was 25% (10:5) or 45% (20:20) of the initial sugar solution. Imidacloprid at its median lethal dose (LD50) in the sugar solution reduced this post-feeding food transmission to 27% (20:20). Our results show that differences in food intake exist within caged bees that may lead to differential exposure that can influence the interpretation of toxicity tests.

Roller to separator contact forces and cage to shaft speed ratios in roller bearings

NASA Technical Reports Server (NTRS)

Nypan, L. J.

1978-01-01

Cage to roller force measurements, cage to shaft speed ratios are reported for 115- and 118-mm bore roller bearings operating at speeds of 4000, 8000, and 12,000 rpm under loads ranging from 360 to 6670 N (80 to 1500 lb).

48 CFR 204.7204 - Maintenance of the CAGE file.

Code of Federal Regulations, 2014 CFR

2014-10-01

... electronic equivalent, to— DLA Logistics Information Service, DLIS-SBB, Federal Center, 74 Washington Avenue... Maintenance of the CAGE file. (a) DLA Logistics Information Service will accept written requests for changes...) Additional guidance for maintaining CAGE codes is in Volume 7 of DoD 4100.39-M, Federal Logistics Information...

48 CFR 204.7202-1 - CAGE codes.

Code of Federal Regulations, 2010 CFR

2010-10-01

....39-M, Federal Logistics Information System (FLIS) Procedures Manual, prescribe use of CAGE codes. (b..., Federal Center, 74 Washington Avenue, North, Battle Creek, MI 49017-3084. Their telephone number is: toll-free 1-888-352-9333); (B) The on-line access to the CAGE file through the Defense Logistics Information...

48 CFR 204.7204 - Maintenance of the CAGE file.

Code of Federal Regulations, 2011 CFR

2011-10-01

... electronic equivalent, to— DLA Logistics Information Service, DLIS-SBB, Federal Center, 74 Washington Avenue... Maintenance of the CAGE file. (a) DLA Logistics Information Service will accept written requests for changes...) Additional guidance for maintaining CAGE codes is in Volume 7 of DoD 4100.39-M, Federal Logistics Information...

48 CFR 204.7204 - Maintenance of the CAGE file.

Code of Federal Regulations, 2013 CFR

2013-10-01

... electronic equivalent, to— DLA Logistics Information Service, DLIS-SBB, Federal Center, 74 Washington Avenue... Maintenance of the CAGE file. (a) DLA Logistics Information Service will accept written requests for changes...) Additional guidance for maintaining CAGE codes is in Volume 7 of DoD 4100.39-M, Federal Logistics Information...

48 CFR 204.7204 - Maintenance of the CAGE file.

Code of Federal Regulations, 2012 CFR

2012-10-01

... electronic equivalent, to— DLA Logistics Information Service, DLIS-SBB, Federal Center, 74 Washington Avenue... Maintenance of the CAGE file. (a) DLA Logistics Information Service will accept written requests for changes...) Additional guidance for maintaining CAGE codes is in Volume 7 of DoD 4100.39-M, Federal Logistics Information...

Abnormal Behavior in Relation to Cage Size in Rhesus Monkeys

ERIC Educational Resources Information Center

Paulk, H. H.; And Others

1977-01-01

Examines the effects of cage size on stereotyped and normal locomotion and on other abnormal behaviors in singly caged animals, whether observed abnormal behaviors tend to co-occur, and if the development of an abnormal behavior repertoire leads to reduction in the number of normal behavior categories. (Author/RK)

Binding of chemical warfare agent simulants as guests in a coordination cage: contributions to binding and a fluorescence-based response.

PubMed

Taylor, Christopher G P; Piper, Jerico R; Ward, Michael D

2016-05-07

Cubic coordination cages act as competent hosts for several alkyl phosphonates used as chemical warfare agent simulants; a range of cage/guest structures have been determined, contributions to guest binding analysed, and a fluorescent response to guest binding demonstrated.

Building a better Faraday cage

NASA Astrophysics Data System (ADS)

MartinAlfven; Wright, David; skocpol; Rounce, Graham; Richfield, Jon; W, Nick; wheelsonfire

2015-11-01

In reply to the physicsworld.com news article “Are Faraday cages less effective than previously thought?” (15 September, http://ow.ly/SfklO), about a study that indicated, based on mathematical modelling, that conducting wire-mesh cages may not be as good at excluding electromagnetic radiation as is commonly assumed.

The fabrication of plastic cages for suspension in mass air flow racks.

PubMed

Nielsen, F H; Bailey, B

1979-08-01

A cage for suspension in mass air flow racks was constructed of plastic and used to house rats. Little or no difficulty was encountered with the mass air flow rack-suspended cage system during the 4 years it was used for the study of trace elements.

50 CFR 648.75 - Cage identification.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Atlantic Surf Clam and Ocean Quahog Fisheries § 648.75 Cage identification. Link to an amendment published.... Before offloading, all cages that contain surfclams or ocean quahogs must be tagged with tags acquired...) Observers. (i) The Regional Administrator may allow the shucking of surfclams or ocean quahogs at sea if he...

International standardization of cage designs and feeding regimes for honey bee in vitro experiments

USDA-ARS?s Scientific Manuscript database

The aim of this study was to improve and standardize cage systems for maintaining adult honey bee workers under in vitro laboratory conditions. To achieve this goal, we experimentally evaluated the impact of different cages, developed by scientists of the international research network COLOSS (Preve...

Probes for the micellar cage effect. The magnetic 13c-isotope effect and a new cage product in the photolysis of dibenzyl ketone

NASA Astrophysics Data System (ADS)

Kraeutler, Bernhard; Turro, Nicholas J.

1980-03-01

An isotopic enrichment factor, α, is employed as a novel probe to study the effect of solute and of detergent concentration on micellar parameters. The formation of a new cage product is also found to follow monotonically the concentration of micelles in aqueous detergent solutions. It is shown by these probes that the average occupancy of the micelles by the solute does not significantly alter the dynamic micellar behavior with respect to reactions that occur in the micelle cage.

Electronic structure, stability and magnetic properties of small M1-4(M = Fe, Co, Ni) clusters encapsulated inside a (BN)48 cage

NASA Astrophysics Data System (ADS)

Liang, Wenjuan; Jia, Jianfeng; Lv, Jin; Wu, Haishun

2015-02-01

The geometrical structure and magnetic properties of M1-4(M = Fe, Co and Ni) clusters within a (BN)48 cage were calculated at the BPW91/LanL2DZ level. The small M1-4 clusters generally prefer an off-centered position near the hexagonal rings in the (BN)48 cages. The (BN)48 cages can increase the stability of these small magnetic clusters while protecting the magnetic nature of M and M2 clusters.

Flow Cage Assemblies

NASA Technical Reports Server (NTRS)

Bar-Cohen, Yoseph (Inventor); Sherrit, Stewart (Inventor); Badescu, Mircea (Inventor); Bao, Xiaoqi (Inventor)

2017-01-01

Apparatus, systems and methods for implementing flow cages and flow cage assemblies in association with high pressure fluid flows and fluid valves are provided. Flow cages and flow assemblies are provided to dissipate the energy of a fluid flow, such as by reducing fluid flow pressure and/or fluid flow velocity. In some embodiments the dissipation of the fluid flow energy is adapted to reduce erosion, such as from high-pressure jet flows, to reduce cavitation, such as by controllably increasing the flow area, and/or to reduce valve noise associated with pressure surge.

Bimetallic cages

NASA Astrophysics Data System (ADS)

Fournier, René; Afzal-Hussain, Sabeen

2013-02-01

We report the results of density functional theory for 39 clusters AxBy (x + y = 10 or 12) where A and B are metals from group 1, 2, 11, 12, 13, or 14 of the periodic table. The chemical compositions were chosen to satisfy an electronic shell closing criterion. We performed an unbiased search for the global minimum (GM) by taboo search in descriptor space in each case. Eight of the 39 putative GM are cages even though none of the clusters contains gold, a metal with a well known propensity to form cages. These cages are large enough to accommodate a dopant atom with an atomic radius varying between 0.7 Å and 1.2 Å. The chemical compositions most likely to produce cages have an element of group 11 alloyed with an element of group 2, 12, or 13.

Open-cage Fullerene-like Graphitic Carbons as Catalysts for Oxidative Dehydrogenation of Isobutane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liang, Chengdu; Xie, Hong; Schwartz, Viviane

We report herein a facile synthesis of fullerene-like cages, which can be opened and closed through simple thermal treatments. A glassy carbon with enclosed fullerene-like cages of 2-3 nm was synthesized through a soft-template approach that created open mesopores of 7 nm. The open mesopores provided access to the fullerene-like cages, which were opened and closed through heat treatments in air and inert gas at various temperatures. Catalytic measurements showed that the open cages displayed strikingly higher activity for the oxidative dehydrogenation of isobutane in comparison to the close ones. We anticipate that this synthesis approach could unravel an avenuemore » for pursuing fundamental understanding of the unique catalytic properties of graphitic carbon nanostructures.« less

Effect of cage design on characteristics of high-speed-jet-lubricated 35-millimeter-bore ball bearing. [turbojet engines

NASA Technical Reports Server (NTRS)

Schuller, F. T.; Pinel, S. I.; Signer, H. R.

1980-01-01

Parametric tests were conducted with a 35 mm bore angular contact ball bearing with a double outer land guided cage. Provisions were made for jet lubrication and outer-ring cooling of the bearing. Test conditions included a combined thrust and radial load at nominal shaft speeds of 48,000 rpm, and an oil-in temperature of 394 K (250 F). Successful operation of the test bearing was accomplished up to 2.5 million DN. Test results were compared with those obtained with similar bearing having a single outer land guided cage. Higher temperatures were generated with the double outer land guided cage bearing, and bearing power loss and cage slip were greater. Cooling the outer ring resulted in a decrease in overall bearing operating temperature.

Electrostatic assembly of binary nanoparticle superlattices using protein cages

NASA Astrophysics Data System (ADS)

Kostiainen, Mauri A.; Hiekkataipale, Panu; Laiho, Ari; Lemieux, Vincent; Seitsonen, Jani; Ruokolainen, Janne; Ceci, Pierpaolo

2013-01-01

Binary nanoparticle superlattices are periodic nanostructures with lattice constants much shorter than the wavelength of light and could be used to prepare multifunctional metamaterials. Such superlattices are typically made from synthetic nanoparticles, and although biohybrid structures have been developed, incorporating biological building blocks into binary nanoparticle superlattices remains challenging. Protein-based nanocages provide a complex yet monodisperse and geometrically well-defined hollow cage that can be used to encapsulate different materials. Such protein cages have been used to program the self-assembly of encapsulated materials to form free-standing crystals and superlattices at interfaces or in solution. Here, we show that electrostatically patchy protein cages--cowpea chlorotic mottle virus and ferritin cages--can be used to direct the self-assembly of three-dimensional binary superlattices. The negatively charged cages can encapsulate RNA or superparamagnetic iron oxide nanoparticles, and the superlattices are formed through tunable electrostatic interactions with positively charged gold nanoparticles. Gold nanoparticles and viruses form an AB8fcc crystal structure that is not isostructural with any known atomic or molecular crystal structure and has previously been observed only with large colloidal polymer particles. Gold nanoparticles and empty or nanoparticle-loaded ferritin cages form an interpenetrating simple cubic AB structure (isostructural with CsCl). We also show that these magnetic assemblies provide contrast enhancement in magnetic resonance imaging.

2-D DIGE and MS/MS analysis of protein serum expression in rats housed in concrete and clay cages in winter.

PubMed

Kim, Jong-Choon; Kim, Jin Young; Yeom, Seok Ran; Jeong, Bo Yoon; Hwang, Hey-Zoo; Park, Keum-Joo; Lee, Seung-won

2008-09-01

In a previous study, we examined the physiological responses of male Sprague-Dawley rats over a 4-week exposure to concrete and clay cages. No general toxicological changes were observed in rats exposed to either of the two cage types in summer. Under winter conditions, however, various general toxicological effects were detected in rats housed in concrete cages, although rats housed in clay cages showed no such effects. The infrared thermographic examination indicated that skin temperature in the concrete-housed rats was abnormally low, but not so in the clay-housed rats. We examined proteomic changes in the serum of rats housed in winter in concrete and clay cages using two-dimensional differential in-gel electrophoresis and mass spectrometry/mass spectrometry. Five proteins were identified and quantitatively validated; all were cold stress-induced, acute phase proteins that were either up-regulated (haptoglobin) or down-regulated (alpha-1-inhibitor III, alpha-2u globulin, complement component 3, and vitamin D-binding protein) in the concrete-housed rats. These results suggest that the 4-week exposure to a concrete cage in winter elicited a typical systemic inflammatory reaction (i.e. acute phase response) in the exposed rats.

Urodynamic measurements reflect physiological bladder function in rats.

PubMed

Schneider, Marc P; Sartori, Andrea M; Tampé, Juliane; Moors, Selina; Engmann, Anne K; Ineichen, Benjamin V; Hofer, Anna-Sophie; Schwab, Martin E; Kessler, Thomas M

2018-04-01

Our objective was to investigate and compare bladder function in rats assessed by metabolic cage and by urodynamic measurements in fully awake animals. Bladder function of female Lewis rats was investigated in naïve animals by metabolic cage at baseline, 14-16 days after bladder catheter and external urethral sphincter electromyography electrode implantation in fully awake animals by urodynamics, and again by metabolic cage. Investigating the same animals (n = 8), voided volume, average flow, and duration of voiding were similar (P > 0.05) in naïve animals measured by metabolic cage and after catheter implantation by urodynamic measurements and by metabolic cage. In naïve animals measured by metabolic cage, voided volumes were significantly different in the light (resting phase) versus the dark (active phase) part of the 24 h cycle (mean difference 0.14 mL, 21%, P = 0.004, n = 27). Lower urinary tract function assessed by metabolic cage or by urodynamic meaurements in fully awake rats was indistinguishable. Thus, catheter implantation did not significantly change physiological bladder function. This shows that urodynamic measurements in awake animals are an appropriate approach to study lower urinary tract function in health and disease in animal models, directly paralleling the human diagnostic procedures. © 2017 Wiley Periodicals, Inc.

Porous biodegradable lumbar interbody fusion cage design and fabrication using integrated global-local topology optimization with laser sintering.

PubMed

Kang, Heesuk; Hollister, Scott J; La Marca, Frank; Park, Paul; Lin, Chia-Ying

2013-10-01

Biodegradable cages have received increasing attention for their use in spinal procedures involving interbody fusion to resolve complications associated with the use of nondegradable cages, such as stress shielding and long-term foreign body reaction. However, the relatively weak initial material strength compared to permanent materials and subsequent reduction due to degradation may be problematic. To design a porous biodegradable interbody fusion cage for a preclinical large animal study that can withstand physiological loads while possessing sufficient interconnected porosity for bony bridging and fusion, we developed a multiscale topology optimization technique. Topology optimization at the macroscopic scale provides optimal structural layout that ensures mechanical strength, while optimally designed microstructures, which replace the macroscopic material layout, ensure maximum permeability. Optimally designed cages were fabricated using solid, freeform fabrication of poly(ε-caprolactone) mixed with hydroxyapatite. Compression tests revealed that the yield strength of optimized fusion cages was two times that of typical human lumbar spine loads. Computational analysis further confirmed the mechanical integrity within the human lumbar spine, although the pore structure locally underwent higher stress than yield stress. This optimization technique may be utilized to balance the complex requirements of load-bearing, stress shielding, and interconnected porosity when using biodegradable materials for fusion cages.

Generalized Stone-Wales transformation as the possible origin of ferromagnetism in polymeric C60: a density-functional theory study.

PubMed

Ribas-Ariño, J; Novoa, Juan J

2006-11-07

Recently, there has been a proposal [Y.-H. Kim et al., Phys. Rev. B 68, 125420 (2003)] suggesting that ferromagnetic interactions in compressed and heated polymeric-C(60) solids could be due to the existence of triplet open cages resulting from successive generalized Stone-Wales transformations within the C(60) cage. Here, by performing B3LYP3-21G and B3LYP6-31G(d) optimizations, we carried out a systematic investigation of the thermodynamics and kinetics of the mechanism of generation of these open cages in their closed-shell singlet, open-shell singlet, and triplet states. We also computed the magnetic interactions induced by the open cages presenting a triplet ground state. Our results indicate that this mechanism is not appropriate to explain the ferromagnetism found in compressed and heated polymeric C(60) for the following reasons: (a) the formation of the only open cage presenting a triplet ground state requires overpassing a highest energy point of 318 kcal/mol, well above other competitive mechanisms reported in the literature; the triplet open cages formed are not stable against their transformation into a diamagnetic intermediate; (c) the magnetic interactions between two adjacent triplet open cages are antiferromagnetic.

Numerical study on the hydrodynamic characteristics of biofouled full-scale net cage

NASA Astrophysics Data System (ADS)

Bi, Chun-wei; Zhao, Yun-peng; Dong, Guo-hai

2015-06-01

The effect of biofouling on the hydrodynamic characteristics of the net cage is of particular interest as biofouled nettings can significantly reduce flow of well-oxygenated water reaching the stocked fish. For computational efficiency, the porous-media fluid model is proposed to simulate flow through the biofouled plane net and full-scale net cage. The porous coefficients of the porous-media fluid model can be determined from the quadratic-function relationship between the hydrodynamic forces on a plane net and the flow velocity using the least squares method. In this study, drag forces on and flow fields around five plane nets with different levels of biofouling are calculated by use of the proposed model. The numerical results are compared with the experimental data of Swift et al. (2006) and the effectiveness of the numerical model is presented. On that basis, flow through full-scale net cages with the same level of biofouling as the tested plane nets are modeled. The flow fields inside and around biofouled net cages are analyzed and the drag force acting on a net cage is estimated by a control volume analysis method. According to the numerical results, empirical formulas of reduction in flow velocity and load on a net cage are derived as function of drag coefficient of the corresponding biofouled netting.

Strains in trussed spine interbody fusion implants are modulated by load and design.

PubMed

Caffrey, Jason P; Alonso, Eloy; Masuda, Koichi; Hunt, Jessee P; Carmody, Cameron N; Ganey, Timothy M; Sah, Robert L

2018-04-01

Titanium cages with 3-D printed trussed open-space architectures may provide an opportunity to deliver targeted mechanical behavior in spine interbody fusion devices. The ability to control mechanical strain, at levels known to stimulate an osteogenic response, to the fusion site could lead to development of optimized therapeutic implants that improve clinical outcomes. In this study, cages of varying design (1.00 mm or 0.75 mm diameter struts) were mechanically characterized and compared for multiple compressive load magnitudes in order to determine what impact certain design variables had on localized strain. Each cage was instrumented with small fiducial sphere markers (88 total) at each strut vertex of the truss structure, which comprised of 260 individual struts. Cages were subjected to a 50 N control, 1000 N, or 2000 N compressive load between contoured loading platens in a simulated vertebral fusion condition, during which the cages were imaged using high-resolution micro-CT. The cage was analyzed as a mechanical truss structure, with each strut defined as the connection of two vertex fiducials. The deformation and strain of each strut was determined from 50 N control to 1000 N or 2000 N load by tracking the change in distance between each fiducial marker. As in a truss system, the number of struts in tension (positive strain) and compression (negative strain) were roughly equal, with increased loads resulting in a widened distribution (SD) compared with that at 50 N tare load indicating increased strain magnitudes. Strain distribution increased from 1000 N (+156 ± 415 με) to 2000 N (+180 ± 605 με) in 1.00 mm cages, which was similar to 0.75 mm cages (+132 ± 622 με) at 1000 N load. Strain amplitudes increased 42%, from 346με at 1000 N to 492με at 2000 N, for 1.00 mm cages. At 1000 N, strain amplitude in 0.75 mm cages (481με) was higher by 39% than that in 1.00 mm cages. These amplitudes corresponded to the mechanobiological range of bone homeostasis+formation, with 63 ± 2% (p < .05 vs other groups), 72 ± 3%, and 73 ± 1% of struts within that range for 1.00 mm at 1000 N, 1.00 mm at 2000 N, and 0.75 mm at 1000 N, respectively. The effective compressive modulus for both cage designs was also dependent on strut diameter, with modulus decreasing from 12.1 ± 2.3 GPa (1.25 mm) to 9.2 ± 7.5 GPa (1.00 mm) and 3.8 ± 0.6 GPa (0.75 mm). This study extended past micro-scale mechanical characterization of trussed cages to compare the effects of design on cage mechanical behavior at moderate (1000 N) and strenuous (2000 N) load levels. The findings suggest that future cage designs may be modulated to target desired mechanical strain regimes at physiological loads. Copyright © 2018 Elsevier Ltd. All rights reserved.

Structural optimisation of cage induction motors using finite element analysis

NASA Astrophysics Data System (ADS)

Palko, S.

The current trend in motor design is to have highly efficient, low noise, low cost, and modular motors with a high power factor. High torque motors are useful in applications like servo motors, lifts, cranes, and rolling mills. This report contains a detailed review of different optimization methods applicable in various design problems. Special attention is given to the performance of different methods, when they are used with finite element analysis (FEA) as an objective function, and accuracy problems arising from the numerical simulations. Also an effective method for designing high starting torque and high efficiency motors is presented. The method described in this work utilizes FEA combined with algorithms for the optimization of the slot geometry. The optimization algorithm modifies the position of the nodal points in the element mesh. The number of independent variables ranges from 14 to 140 in this work.

Transcutaneous RF-Powered Implantable Minipump Driven by a Class-E Transmitter

PubMed Central

Moore, William H.; Holschneider, Daniel P.; Givrad, Tina K.

2007-01-01

We describe the design and testing of an inductive coupling system used to power an implantable minipump for applications in ambulating rats. A 2 MHz class-E oscillator driver powered a coil transmitter wound around a 33-cm-diameter rat cage. A receiver coil, a filtered rectifier, and a voltage-sensitive switch powered the implant. The implant DC current at the center of the primary coil (5.1 V) exceeded the level required to activate the solenoid valve in the pump. The variations of the implant current in the volume of the primary coil reflected the variations of the estimated coupling coefficient between the two coils. The pump could be activated in-vivo, while accommodating the vertical and horizontal movements of the animal. Advantages of this design include a weight reduction for the implant, an operation independent from a finite power source, and a remote activation/deactivation. PMID:16916107

Transcutaneous RF-powered implantable minipump driven by a class-E transmitter.

PubMed

Moore, William H; Holschneider, Daniel P; Givrad, Tina K; Maarek, Jean-Michel I

2006-08-01

We describe the design and testing of an inductive coupling system used to power an implantable minipump for applications in ambulating rats. A 2 MHz class-E oscillator driver powered a coil transmitter wound around a 33-cm-diameter rat cage. A receiver coil, a filtered rectifier, and a voltage-sensitive switch powered the implant. The implant DC current at the center of the primary coil (5.1 V) exceeded the level required to activate the solenoid valve in the pump. The variations of the implant current in the volume of the primary coil reflected the variations of the estimated coupling coefficient between the two coils. The pump could be activated in-vivo, while accommodating the vertical and horizontal movements of the animal. Advantages of this design include a weight reduction for the implant, an operation independent from a finite power source, and a remote activation/deactivation.

Induction of the cellular stress response in Chironomus (Diptera)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pardalis, G.; Hudson, L.A.; Ciborowski, J.J.H.

1995-12-31

The accumulation of stress or heat shock proteins is involved in the protection and defense of a cell from environmentally induced damage. Under stressful conditions, cytoplasmic stress protein 70 migrates to the nucleus where it assists in the restoration of the nucleolar function. The authors have demonstrated a dose-response relationship between incidence of decreased nucleolar size in chironomid salivary glands and degree of sediment contamination. Reduced nucleolar size is indicative of reduced nucleolar function. The relationship between nucleolus size and stress protein accumulation is being explored. They are conducting experiments on chironomids to characterize the response elicited by heat shockmore » and PAH exposure in the laboratory to determine if the simultaneous action of more than one stressor can significantly alter the stress response. Simultaneous studies are being conducted to validate these biomarkers in mesocosm caging experiments. Aspects of the response will be useful as biomarkers of general stress.« less

Validation of a cage implant system for assessing in vivo performance of long-acting release microspheres.

PubMed

Doty, Amy C; Hirota, Keiji; Olsen, Karl F; Sakamoto, Naoya; Ackermann, Rose; Feng, Meihua R; Wang, Yan; Choi, Stephanie; Qu, Wen; Schwendeman, Anna; Schwendeman, Steven P

2016-12-01

Here we describe development of a silicone rubber/stainless steel mesh cage implant system, much like that used to assess biocompatibility of biomaterials [1], for easy removal of injectable polymer microspheres in vivo. The sterile cage has a type 316 stainless steel mesh size (38 μm) large enough for cell penetration and free fluid flow in vivo but small enough for microsphere retention, and a silicone rubber shell for injection of the microspheres. Two model drugs, the poorly soluble steroid, triamcinolone acetonide, and the highly water-soluble luteinizing hormone-releasing hormone (LHRH) peptide superagonist, leuprolide, were encapsulated in PLGA microspheres large enough (63-90 μm) to be restrained by the cage implant in vivo. The in vitro release from both formulations was followed by ultra-performance liquid chromatography (UPLC) with and without the cage in a standard release media, PBS pH 7.4 + 0.02% Tween 80 + 0.05% sodium azide, at 37 °C. Pharmacokinetics (PK) in rats was assessed after SC injection or SC in-cage implantation of microspheres with plasma analysis by LC-MS/MS or EIA. Tr-A and leuprolide in vitro release was largely unaffected after the initial burst irrespective of the cage or test tube incubation vessel and release was much slower than observed in vivo for both drugs. Moreover, Tr-A and leuprolide pharmacokinetics with and without the cage were highly similar during the 2-3 week release duration before a significant inflammatory response was caused by the cage implant. Hence, the PK-validated cage implant provides a simple means to recover and evaluate the microsphere drug carriers in vivo during a time window of at least a few weeks in order to characterize the polymer microsphere release and erosion behavior in vivo. This approach may facilitate development of mechanism-based in vitro/in vivo correlations and enable development of more accurate and useful in vitro release tests. Copyright © 2016 Elsevier Ltd. All rights reserved.

Survey of egg producers on the introduction of alternative housing systems for laying hens in Flanders, Belgium.

PubMed

Tuyttens, F A M; Sonck, B; Staes, M; Van Gansbeke, S; Van den Bogaert, T; Ampe, B

2011-04-01

In the context of the European Union ban on battery cages by 2012, a survey was conducted among Flemish egg producers (60% response rate, 140 completed questionnaires) about the introduction and opinion of alternative housing systems. Belgium appears to be among the countries in the European Union that are slower to adopt alternative housing. Belgium's egg industry is thus likely to undergo drastic changes to comply with the 2012 deadline. As of 2010, the battery cage was the dominant housing system (56% housing units, 67% hens), followed by floor housing (33% housing units, 15% hens) and aviary (10% housing units, 15% hens), whereas colony cages and furnished cages were extremely rare. Future- and market-oriented production was the most important reason for choosing a certain type of alternative system, although the importance of hen performance and amount of labor seemed to increase. A quarter of the producers with battery cages had detailed plans to convert to an alternative system (most planned to install aviaries, followed by colony cages, furnished cages, and floor housing) by 2012. Many older farmers indicated that they would stop farming, whereas others found it more profitable to delay the conversion as long as possible. Apart from hen welfare, producers expressed a negative opinion (relative to battery cages) about noncage systems and, to a lesser extent, furnished cages. However, users of alternative systems reported being quite satisfied, except for the amount of labor and hen health. The housing system had several effects on user satisfaction: positive effect of flock size, negative effect of experience with battery cages, and negative effect of outdoor area on hen health. Although not all opinions were supported by evidence, such surveys provide feedback about the success of alternative systems in practice. This information is valuable to further improve these systems and to producers who have yet to convert. Moreover, producer attitude may determine the extent to which legally imposed changes in husbandry environment result in the desired improvement of hen welfare in practice.

Metabolic Cages for a Space Flight Model in the Rat

NASA Technical Reports Server (NTRS)

Harper, Jennifer S.; Mulenburg, Gerald M.; Evans, Juli; Navidi, Meena; Wolinsky, Ira; Arnaud, Sara B.

1994-01-01

A variety of space flight models are available to mimic the physiologic changes seen in the rat during weightlessness. The model reported by Wronski and Morey-Holton has been widely used by many investigators, in musculoskeletal physiologic studies especially, resulting in accumulation of an extensive database that enables scientists to mimic space flight effects in the 1-g environment of Earth. However, information on nutrition or gastrointestinal and renal function in this space flight model is limited by the difficulty in acquiring uncontaminated metabolic specimens for analysis. In the Holton system, a traction tape harness is applied to the tail, and the rat's hindquarters are elevated by attaching the harness to a pulley system. Weight-bearing hind limbs are unloaded, and there is a headward fluid shift. The tail-suspended rats are able to move freely about their cages on their forelimbs and tolerate this procedure with minimal signs of stress. The cage used in Holton's model is basically a clear acrylic box set on a plastic grid floor with the pulley and tail harness system attached to the open top of the cage. Food is available from a square food cup recessed into a corner of the floor. In this system, urine, feces, and spilled food fall through the grid floor onto absorbent paper beneath the cage and cannot be separated and recovered quantitatively for analysis in metabolic balance studies. Commercially available metabolic cages are generally cylindrical and have been used with a centrally located suspension apparatus in other space flight models. The large living area, three times as large as most metabolic cages, and the free range of motion unique to Holton's model, essential for musculoskeletal investigations, were sacrificed. Holton's cages can accommodate animals ranging in weight from 70 to 600 g. Although an alternative construction of Holton's cage has been reported, it does not permit collection of separate urine and fecal samples. We describe the modifications to Holton's food delivery system, cage base, and the addition of a separator system for the collection of urine and fecal samples for metabolic and nutrition studies in the tail suspension model.

Synthesis and Characterization of Polyfunctional Polyhedral Silsesquioxane Cages

NASA Astrophysics Data System (ADS)

Sulaiman, Santy

Recent studies on octameric polyhedral silsesquioxanes, (RSiO1.5 )8, indicate that the silsesquioxane cage is not just a passive component but appears to be involved in electron delocalization with conjugated organic tethers in the excited state. This dissertation presents the synthesis and characterization of (RSiO1.5)8 molecules with unique photophysical properties that provide support for the existence of conjugation that involves the (RSiO1.5)8 cage. The dissertation first discusses the elaboration of octavinylsilsesquioxane via cross-metathesis to form styrenyl-functionalized octasilsesquioxane molecules. Subsequent Heck coupling reactions of p-bromostyrenyl derivative provides vinylstilbene-functionalized octasilsesquioxane. The amino derivative, NH2VinylStilbeneOS, show highly red-shifted emission spectrum (100 nm from the simple organic analog p-vinylstilbene) and high two-photon absorption (TPA) cross-section value (100 GM/moiety), indicating charge-transfer processes involving the silsesquioxane cage as the electron acceptor. The unique photophysical properties of polyfunctional luminescent cubic silsesquioxanes synthesized from ortho-8-, (2,5)-16-, and 24-brominated octaphenylsilsesquioxane (OPS) via Heck coupling show how the steric interactions of the organic tethers at the silsesquioxane cage corner affect conjugation with the silsesquioxane cage. Furthermore, the high TPA cross-section (10 GM/moiety) and photoluminescence quantum yield (20%) of OPS functionalized with 24 acetoxystyrenyl groups suggest that the existence excited states in these molecules with similar energies and decay rates: normal radiative pi- pi* transition and charge transfer involving the silsesquioxane cage. The fluoride ion-catalyzed rearrangement reactions of cage and polymeric silsesquioxanes provide a convenient route to a mixture of deca- and dodecameric silsesquioxane molecules in high yields, giving us the opportunity to investigate the effect of silsesquioxane cage geometry on their photophysical properties. The ability to recycle polymeric silsesquioxane resins, byproducts from cubic silsesquioxane syntheses, into useful cage silsesquioxane molecules adds another advantage. Lastly, we present the synthesis of octa(aminophenyl)silsesquioxane-based epoxy resins with coefficient of thermal expansion (CTE) as low as 25°C/ppm without ceramic fillers. The CTEs of these resins can be tailored over an order of magnitude by choosing epoxy crosslinking agents having different flexibilities.

Does Lordotic Angle of Cage Determine Lumbar Lordosis in Lumbar Interbody Fusion?

PubMed

Hong, Taek-Ho; Cho, Kyu-Jung; Kim, Young-Tae; Park, Jae-Woo; Seo, Beom-Ho; Kim, Nak-Chul

2017-07-01

Retrospective, radiological analysis. To determine that 15° lordotic angle cages create higher lumbar lordosis in open transforaminal lumbar interbody fusion (TLIF) than 4° and 8° cages. Restoration of lumbar lordosis is important to obtain good outcome after lumbar fusion surgery. Various shapes and angles of cages in interbody fusion have been used; however, it is not proved that lordotic angle of cages determine lumbar lordosis. Sixty-seven patients were evaluated after TLIF using 15° cages and screw instrumentation. For comparison, TLIF using 4° lordotic angle cages in 65 patients and 8° cages in 49 patients were analyzed. Lumbar lordosis angles, segmental lordosis angles, disc height, and bony union rate were measured on the radiographs. The lumbar lordosis was 31.1° preoperatively, improved to 42.9° postoperatively, and decreased to 36.4° at the last follow-up in the 15° group. It was 35.8° before surgery, corrected to 41.5° after surgery, and changed to 33.6° at the last follow-up in the 4° group. In the 8° group, it was 32.7° preoperatively, improved to 39.1° postoperatively, and decreased to 34.5° at the last follow-up. These changes showed statistical significances (P < 0.001). The segmental lordosis at L4-5 was 6.6° before surgery, 13.1° after surgery, and 9.8° at the last follow-up in the 15° group. It was 6.9°, 9.5°, and 6.2° in the 4° group and 6.7°, 9.8°, and 8.1° in the 8° group, respectively (P < 0.001). The disc height restoration was better in the 15° group than in the 4° and 8° groups (P < 0.001). Bony union rate was not significant among the three groups (P = 0.087). The lordotic angle of the cages determined restoration of lumbar lordosis after TLIF. Cages with sufficient lordotic angle showed better restoration of lumbar lordosis and prevention of loss of correction. 4.

Autonomous Non-Linear Classification of LPI Radar Signal Modulations

DTIC Science & Technology

2007-09-01

Wigner - Ville distribution ( WVD ), the Choi-Williams distribution (CWD) and a Quadrature...accomplished using the images from the Wigner - Ville distribution and the Choi-Williams distribution for polyphase modulations. For the WVD images, radon...this work. Four detection techniques including the Wigner - Ville distribution ( WVD ), the Choi-Williams distribution (CWD), Quadrature Mirror

Campylobacter pinnipediorum sp. nov., isolated from pinnipeds, comprising Campylobacter pinnipediorum subsp. pinnipediorum subsp. nov. and Campylobacter pinnipediorum subsp. caledonicus subsp. nov.

USDA-ARS?s Scientific Manuscript database

During independent diagnostic screenings of otariid seals in California (US) and phocid seals in Scotland (UK), Campylobacter-like isolates, which differed from the established Campylobacter taxa, were cultured from abscesses and internal organs of different seal species. A polyphasic study was unde...

Current responsive devices for synchronous generators

DOEpatents

Karlicek, Robert F.

1983-01-01

A device for detecting current imbalance between phases of a polyphase alternating current generator. A detector responds to the maximum peak current in the generator, and detecting means generates an output for each phase proportional to the peak current of each phase. Comparing means generates an output when the maximum peak current exceeds the phase peak current.

Streptomyces leeuwenhoekii sp. nov., the producer of chaxalactins and chaxamycins, forms a distinct branch in Streptomyces gene trees

USDA-ARS?s Scientific Manuscript database

A polyphasic study was carried out to establish the taxonomic status of an Atacama Desert isolate, Streptomyces strain C34T, which synthesises novel antibiotics, the chaxalactins and chaxamycins. The organism was shown to have chemotaxonomic, cultural, and morphological properties consistent with it...

Simplified High-Power Inverter

NASA Technical Reports Server (NTRS)

Edwards, D. B.; Rippel, W. E.

1984-01-01

Solid-state inverter simplified by use of single gate-turnoff device (GTO) to commutate multiple silicon controlled rectifiers (SCR's). By eliminating conventional commutation circuitry, GTO reduces cost, size and weight. GTO commutation applicable to inverters of greater than 1-kilowatt capacity. Applications include emergency power, load leveling, drives for traction and stationary polyphase motors, and photovoltaic-power conditioning.

Polyphasic taxonomy of the genus Talaromyces

PubMed Central

Yilmaz, N.; Visagie, C.M.; Houbraken, J.; Frisvad, J.C.; Samson, R.A.

2014-01-01

The genus Talaromyces was described by Benjamin in 1955 as a sexual state of Penicillium that produces soft walled ascomata covered with interwoven hyphae. Phylogenetic information revealed that Penicillium subgenus Biverticillium and Talaromyces form a monophyletic clade distinct from the other Penicillium subgenera. Subsequently, in combination with the recent adoption of the one fungus one name concept, Penicillium subgenus Biverticillium was transferred to Talaromyces. At the time, the new combinations were made based only on phylogenetic information. As such, the aim of this study was to provide a monograph on Talaromyces applying a polyphasic species concept, including morphological, molecular and physiological characters. Based on an ITS, BenA and RPB2 multigene phylogeny, we propose a new sectional classification for the genus, placing the 88 accepted species into seven sections, named sections Bacillispori, Helici, Islandici, Purpurei, Subinflati, Talaromyces and Trachyspermi. We provide morphological descriptions for each of these species, as well as notes on their identification using morphology and DNA sequences. For molecular identification, BenA is proposed as a secondary molecular marker to the accepted ITS barcode for fungi. PMID:25492983

Myodegeneration with fibrosis and regeneration in the pectoralis major muscle of broilers.

PubMed

Sihvo, H-K; Immonen, K; Puolanne, E

2014-05-01

A myopathy affecting the pectoralis major muscle of the commercial broiler has emerged creating remarkable economic losses as well as a potential welfare problem of the birds. We here describe the macroscopic and histologic lesions of this myopathy within 10 pectoralis major muscles of 5- to 6-week-old broilers in Finland. Following macroscopic evaluation and palpation of the muscles, a tissue sample of each was fixed in formalin, processed for histology, and histologically evaluated. The muscles that were macroscopically hard, outbulging, pale, and often accompanied with white striping histologically exhibited moderate to severe polyphasic myodegeneration with regeneration as well as a variable amount of interstitial connective tissue accumulation or fibrosis. All affected cases also exhibited perivenular lymphocyte accumulation. The etiology of this myodegenerative lesion remains yet open. Polyphasic myodegeneration is associated with several previously known etiologies, but palpatory hardness focusing on the pectoralis major, together with perivenular lymphocytes, has not been described in relation to them. The results of this study provide the pathological basis for further studies concerning the etiology of the currently described myopathy.

Enterococcus Xinjiangensis sp. nov., Isolated from Yogurt of Xinjiang, China.

PubMed

Ren, Xiaopu; Li, Mingyang; Guo, Dongqi

2016-09-01

A Gram-strain-positive bacterial strain 48(T) was isolated from traditional yogurt in Xinjiang Province, China. The bacterium was characterized by a polyphasic approach, including 16S rRNA gene sequence analysis, polymerase α subunit (rpoA) gene sequence analysis, determination of DNA G+C content, DNA-DNA hybridization with the type strain of Enterococcus ratti and analysis of phenotypic features. Strain 48(T) accounted for 96.1, 95.8, 95.8, and 95.7 % with Enterococcus faecium CGMCC 1.2136(T), Enterococcus hirae ATCC 9790(T), Enterococcus durans CECT 411(T), and E. ratti ATCC 700914(T) in the 16S rRNA gene sequence similarities, respectively. The sequence of rpoA gene showed similarities of 99.0, 96.0, 96.0, and 96 % with that of E. faecium ATCC 19434(T), Enterococcus villorum LMG12287, E. hirae ATCC 9790(T), and E. durans ATCC 19432(T), respectively. Based upon of polyphasic characterization data obtained in the study, a novel species, Enterococcus xinjiangensis sp. nov., was proposed and the type strain was 48(T)(=CCTCC AB 2014041(T) = JCM 30200(T)).

Comparative study of proliferative kidney disease in grayling Thymallus thymallus and brown trout Salmo trutta fario: an exposure experiment.

PubMed

Schmidt-Posthaus, Heike; Ros, Albert; Hirschi, Regula; Schneider, Ernst

2017-03-21

Proliferative kidney disease (PKD) is an emerging disease threatening wild salmonid populations, with the myxozoan parasite Tetracapsuloides bryosalmonae as the causative agent. Species differences in parasite susceptibility and disease-induced mortality seem to exist. The aim of the present study was to compare incidence, pathology and mortality of PKD in grayling Thymallus thymallus and brown trout Salmo trutta under identical semi-natural conditions. Young-of-the-year grayling and brown trout, free of T. bryosalmonae, were jointly exposed in cage compartments in a river in the northeast of Switzerland during 3 summer months. Wild brown trout were caught by electrofishing near the cage, and PKD status was compared with that of caged animals. Cage-exposed grayling showed a PKD incidence of 1%, regardless of whether parasite infection was determined by means of real-time PCR or histopathology/immunohistochemistry. In contrast, PKD incidence of caged brown trout was 77%. This value was not significantly different to PKD prevalence of wild brown trout caught above and below the cage (60 and 91%, respectively). Mortality in grayling was significantly higher compared with that of brown trout (40 versus 23%); however, grayling mortality was not considered to be associated with PKD. Mortality of caged and infected brown trout was significantly higher than mortality of non-infected caged trout. Histopathology indicated an ongoing mostly acute or chronic active infection in brown trout, which survived until the end of exposure. The results suggest that grayling are less susceptible to infection with T. bryosalmonae compared with brown trout under the tested field conditions.

Effect of Ventilated Caging on Water Intake and Loss in 4 Strains of Laboratory Mice

PubMed Central

Nicolaus, Mackenzie L; Bergdall, Valerie K; Davis, Ian C; Hickman-Davis, Judy M

2016-01-01

Food availability, temperature, humidity, strain, and caging type all affect water consumption by mice. Measurement of transepidermal water loss (TEWL) is a new technique for the quantification of water turnover in mice. To understand water turnover in common strains of adult mice, male and female SCID, SKH, C57BL/6, and FVB mice were housed in same-sex groups of 5 animals in static cages or IVC. Body weight, TEWL, urine osmolality, and water consumption of mice and intracage temperature and humidity were measured every 48 h for comparison. Static cages were monitored for 7 d and IVC for 14 d before cage change. Female SCID, FVB, and C57 mice drank less water than did their male counterparts. Male and female SCID, SKH, and FVB mice in IVC drank less water and had higher urine osmolality than did those in static cages. In SCID and SKH mice, TEWL paralleled water consumption. C57 mice in static cages drank less water, had lower urine osmolality, and had less TEWL than did those in IVC. Temperature and humidity within the cage was higher than the macroenvironmental levels for all housing conditions, mouse strains, and sexes. Temperatures within IVC ranged from 76.6 to 81.4 °F compared with 69 ± 0.4 °F in the room. Humidity within IVC ranged from 68% to 79% compared with 27.o% ± 2.7% within the room. These data demonstrate that mouse strain and housing conditions significantly influence water balance and indicate that macroenvironmental measurements do not always reflect the intracage environment. PMID:27657706

Implications of Natural Occlusion of Ventilated Racks on Ammonia and Sanitation Practices

PubMed Central

Creamer, Michelle A; Petty, Joann; Martin, Tara; Bergdall, Valerie; Hickman-Davis, Judy M

2014-01-01

Examination of ventilated rat racks prior to semiannual sanitation revealed silicone nozzles and ventilation ports that were partially or completely occluded with granular debris. We subsequently sought to document performance standards for rack sanitation and investigate the effect of ventilation port occlusion on rack function and animal husbandry practices. We hypothesized that individually ventilated cages with occluded airflow would require more frequent cage changes, comparable to those for static cages (that is, every 3 to 4 d). Sprague–Dawley rats were housed under one of 4 conditions: no airflow occlusion, occluded air-supply inlet, occluded air-exhaust outlet, and occlusion of both inlet and outlet. Cages were changed when daily ammonia concentration exceeded 20 ppm or after 14 d had elapsed. Most cages with unoccluded or partial airflow occlusion remained below the 20 ppm limit until day 12 or 13. Cages with occlusion of both inlet and outlet exceeded 20 ppm ammonia by as early as day 5. Airflow was significantly lower in cages with occlusion of both inlet and outlet airflow. Weekly inspection revealed that occlusion of ventilation ports was detectable by 3 mo after semiannual sanitation. This study demonstrates that silicone nozzles should be removed prior to rack sanitation to improve the effectiveness of cleaning ventilation ports and nozzles. While the rack is in use, silicone nozzles and ventilation ports should be inspected regularly to identify occlusion that is likely to diminish environmental quality in the cage. Intracage ammonia levels are significantly higher when both inlet and outlet airflow are occluded. PMID:24602544

Implications of natural occlusion of ventilated racks on ammonia and sanitation practices.

PubMed

Creamer, Michelle A; Petty, Joann; Martin, Tara; Bergdall, Valerie; Hickman-Davis, Judy M

2014-03-01

Examination of ventilated rat racks prior to semiannual sanitation revealed silicone nozzles and ventilation ports that were partially or completely occluded with granular debris. We subsequently sought to document performance standards for rack sanitation and investigate the effect of ventilation port occlusion on rack function and animal husbandry practices. We hypothesized that individually ventilated cages with occluded airflow would require more frequent cage changes, comparable to those for static cages (that is, every 3 to 4 d). Sprague-Dawley rats were housed under one of 4 conditions: no airflow occlusion, occluded air-supply inlet, occluded air-exhaust outlet, and occlusion of both inlet and outlet. Cages were changed when daily ammonia concentration exceeded 20 ppm or after 14 d had elapsed. Most cages with unoccluded or partial airflow occlusion remained below the 20 ppm limit until day 12 or 13. Cages with occlusion of both inlet and outlet exceeded 20 ppm ammonia by as early as day 5. Airflow was significantly lower in cages with occlusion of both inlet and outlet airflow. Weekly inspection revealed that occlusion of ventilation ports was detectable by 3 mo after semiannual sanitation. This study demonstrates that silicone nozzles should be removed prior to rack sanitation to improve the effectiveness of cleaning ventilation ports and nozzles. While the rack is in use, silicone nozzles and ventilation ports should be inspected regularly to identify occlusion that is likely to diminish environmental quality in the cage. Intracage ammonia levels are significantly higher when both inlet and outlet airflow are occluded.

[Comprehensive testing system for cardiorespiratory interaction research].

PubMed

Zhang, Zhengbo; Wang, Buqing; Wang, Weidong; Zheng, Jiewen; Liu, Hongyun; Li, Kaiyuan; Sun, Congcong; Wang, Guojing

2013-04-01

To investigate the modulation effects of breathing movement on cardiovascular system and to study the physiological coupling relationship between respiration and cardiovascular system, we designed a comprehensive testing system for cardiorespiratory interaction research. This system, comprising three parts, i. e. physiological signal conditioning unit, data acquisition and USB medical isolation unit, and a PC based program, can acquire multiple physiological data such as respiratory flow, rib cage and abdomen movement, electrocardiograph, artery pulse wave, cardiac sounds, skin temperature, and electromyography simultaneously under certain experimental protocols. Furthermore this system can be used in research on short-term cardiovascular variability by paced breathing. Preliminary experiments showed that this system could accurately record rib cage and abdomen movement under very low breathing rate, using respiratory inductive plethysmography to acquire respiration signal in direct-current coupling mode. After calibration, this system can be used to estimate ventilation non-intrusively and correctly. The PC based program can generate audio and visual biofeedback signal, and guide the volunteers to perform a slow and regular breathing. An experiment on healthy volunteers showed that this system was able to guide the volunteers to do slow breathing effectively and simultaneously record multiple physiological data during the experiments. Signal processing techniques were used for off-line data analysis, such as non-invasive ventilation calibration, QRS complex wave detection, and respiratory sinus arrhythmia and pulse wave transit time calculation. The experiment result showed that the modulation effect on RR interval, respiratory sinus arrhythmia (RSA), pulse wave transit time (PWTT) by respiration would get stronger with the going of the slow and regular breathing.

Transmission probabilities of mouse parvovirus 1 to sentinel mice chronically exposed to serial dilutions of contaminated bedding.

PubMed

Besselsen, David G; Myers, Erin L; Franklin, Craig L; Korte, Scott W; Wagner, April M; Henderson, Kenneth S; Weigler, Benjamin J

2008-04-01

Intermittent serodetection of mouse parvovirus (MPV) infections in animal facilities occurs frequently when soiled bedding sentinel mouse monitoring systems are used. We evaluated induction of seroconversion in naïve single-caged weanling ICR mice (n = 10 per group) maintained on 5-fold serially diluted contaminated bedding obtained from SCID mice persistently shedding MPV1e. Soiled bedding from the infected SCID mice was collected, diluted, and redistributed weekly to cages housing ICR mice to represent chronic exposure to MPV at varying prevalence in a research colony. Sera was collected every other week for 12 wk and evaluated for reactivity to MPV nonstructural and capsid antigens by multiplex fluorescent immunoassay. Mice were euthanized after seroconversion, and DNA extracted from lymph node and spleen was evaluated by quantitative PCR. Cumulative incidence of MPV infection for each of the 7 soiled bedding dilution groups (range, 1:5 to 1:78125 [v/v]) was 100%, 100%, 90%, 20%, 70%, 60%, and 20%, respectively. Most seropositive mice (78%) converted within the first 2 to 3 wk of soiled bedding exposure, correlating to viral exposure when mice were 4 to 7 wk of age. Viral DNA was detected in lymphoid tissues collected from all mice that were seropositive to VP2 capsid antigen, whereas viral DNA was not detected in lymphoid tissue of seronegative mice. These data indicate seroconversion occurs consistently in young mice exposed to high doses of virus equivalent to fecal MPV loads observed in acutely infected mice, whereas seroconversion is inconsistent in mice chronically exposed to lower doses of virus.

Crystal structure of YbCu6In6 and mixed valence behavior of Yb in YbCu(6-x)In(6+x) (x = 0, 1, and 2) solid solution.

PubMed

Subbarao, Udumula; Peter, Sebastian C

2012-06-04

High quality single crystals of YbCu(6)In(6) have been grown using the flux method and characterized by means of single crystal X-ray diffraction data. YbCu(6)In(6) crystallizes in the CeMn(4)Al(8) structure type, tetragonal space group I4/mmm, and the lattice constants are a = b = 9.2200(13) Å and c = 5.3976(11) Å. The crystal structure of YbCu(6)In(6) is composed of pseudo-Frank-Kasper cages filled with one ytterbium atom in each ring. The neighboring cages share corners along [100] and [010] to build the three-dimensional network. YbCu(6-x)In(6+x) (x = 0, 1, and 2) solid solution compounds were obtained from high frequency induction heating and characterized using powder X-ray diffraction. The magnetic susceptibilities of YbCu(6-x)In(6+x) (x = 0, 1, and 2) were investigated in the temperature range 2-300 K and showed Curie-Weiss law behavior above 50 K, and the experimentally measured magnetic moment indicates mixed valent ytterbium. A deviation in inverse susceptibility data at 200 K suggests a valence transition from Yb(2+) to Yb(3+) as the temperature decreases. An increase in doping of Cu at the Al2 position enhances the disorder in the system and enhancement in the trivalent nature of Yb. Electrical conductivity measurements show that all compounds are of a metallic nature.

Responses of shortfin eel (Anguilla australis) exposed in situ to pulp and paper effluent.

PubMed

van den Heuvel, Michael R; Landman, Michael J; Tremblay, Louis A

2006-10-01

The responses of shortfin eel (Anguilla australis) to discharges from two pulp and paper mills, municipal wastewater, and a geothermal power plant wastewater were examined. Eels were caged at 3 sites along the Tarawera River, North Island, New Zealand, to explore effects of a 3-wk exposure down a contamination gradient (Ref --> D1 --> D2). Most of the observed effects were seen in eels caged at the furthest downstream site (D2), below all the discharge areas. General hematology in eels was unaffected, as measures did not differ markedly at the two downstream sites compared with the reference site. At D2, eels were significantly lighter per unit length (reduced condition factor), although liver and spleen size (LSI and SSI) were unaffected. Significantly elevated circulating sex steroid concentrations (testosterone and estradiol) were measured in D2 eels and increasing sex steroid levels at both sites downstream of the reference site were observed. Significant ethoxyresorufin O-deethylase (EROD) activity induction was seen in D2 eels and bile chemistry showed significant accumulation of pyrene and retene equivalents. However, significantly greater concentrations of total resin acids were found in the bile of eels from the intermediate site (D1), between the two pulp and paper mills. The higher polycyclic aromatic hydrocarbon (PAH) equivalents found in the bile of D2 eels suggest that resin acid neutrals, particularly retene, are responsible for some of the effects observed in eels at the furthest downstream exposure site. Levels of pulp and paper mill extractives in sediment, including the PAH retene, support this conclusion.

The effects of housing environment on liver health of laying hens

USDA-ARS?s Scientific Manuscript database

Fatty liver is a common energy metabolic disorder in caged hens. Considering that the egg industry is shifting from conventional cages to alternative housing systems such as enriched cages, the objective of this study was to determine the effects of type of housing, including access to perches, on f...

Forced Hot Air to Dry Feces and Kill Bacteria on Transport Cage Flooring

USDA-ARS?s Scientific Manuscript database

Due to fecal shedding from positive birds, broiler transport cages can be contaminated with human bacterial pathogens leading to cross contamination of previously negative broilers during live haul. Earlier work has shown that drying soiled or washed cages for 24 to 48 hours can lower or even elimi...

Identification of Alcohol Disorders at a University Mental Health Centre, Using the CAGE.

ERIC Educational Resources Information Center

Ross, Helen E.; Tisdall, Gordon W.

1994-01-01

Examined usefulness of CAGE in screening for alcohol use disorders in university students (n=110) attending campus psychiatric health service. Fourteen students were identified as having current alcohol use disorder by means of Computerized Diagnostic Interview Schedule. Results suggest that CAGE is able in this population to detect usually mild…

Spray washing, absorbent cornstarch powder, and dry time to reduce bacterial numbers on soiled transport cage flooring

USDA-ARS?s Scientific Manuscript database

Broiler transport cages are often used repeatedly without washing and fecal matter deposited on the floor surface can transfer Campylobacter from one flock to another. Allowing feces to dry is an effective but slow and logistically impractical means to kill Campylobacter in soiled transport cages. ...

Polymers containing borane or carborane cage compounds and related applications

DOEpatents

Bowen, III, Daniel E.; Eastwood, Eric A [Raymore, MO

2012-06-05

Polymers comprising residues of borane and/or carborane cage compound monomers having at least one polyalkoxy silyl substituent. Such polymers can further comprise one or more reactive matrices and/or co-monomers covalently bound with the cage compound monomer residues. Methods of making and applications for using such polymers are also disclosed.

Mineral content of eggs differs with hens strain, age and rearing environment

USDA-ARS?s Scientific Manuscript database

Egg nutrient quality is strongly influenced by hen diet but is also affected by rearing environment, hen strain and hen age. The objective of the current study was to determine the effect of: 1) conventional battery cages 2) enrichable cage systems 3) enriched colony housing 4) cage free and 5) free...

The effect of perch availability during pullet rearing and egg laying on musculoskeletal health of caged White Leghorn hens

USDA-ARS?s Scientific Manuscript database

A major skeletal problem of conventionally caged hens is increased susceptibility to osteoporosis mainly due to lack of exercise. Osteoporosis is characterized by a progressive decrease in mineralized structural bone. Whereas considerable attention has been given to enriching laying cages, little r...

Horizontal transmission of Salmonella and Campylobacter among caged and cage-free laying hens

USDA-ARS?s Scientific Manuscript database

In each of five trials, laying hens (56-72 wk-of-age) were challenged orally, intracolonally, and intravaginally with Salmonella and Campylobacter. One wk post inoculation, challenged hens (n=3) were commingled with non-challenged hens (n=12) in conventional wire cages, on all wire slats, or on all...

Caging Mechanism for a drag-free satellite position sensor

NASA Technical Reports Server (NTRS)

Hacker, R.; Mathiesen, J.; Debra, D. B.

1976-01-01

A disturbance compensation system for satellites based on the drag-free concept was mechanized and flown, using a spherical proof mass and a cam-guided caging mechanism. The caging mechanism controls the location of the proof mass for testing and constrains it during launch. Design requirements, design details, and hardware are described.

Automated recording of home cage activity and temperature of individual rats housed in social groups: The Rodent Big Brother project

PubMed Central

Tse, Karen; Grant, Claire; Keerie, Amy; Simpson, David J.; Pedersen, John C.; Rimmer, Victoria; Leslie, Lauren; Klein, Stephanie K.; Karp, Natasha A.; Sillito, Rowland; Chartsias, Agis; Lukins, Tim; Heward, James; Vickers, Catherine; Chapman, Kathryn; Armstrong, J. Douglas

2017-01-01

Measuring the activity and temperature of rats is commonly required in biomedical research. Conventional approaches necessitate single housing, which affects their behavior and wellbeing. We have used a subcutaneous radiofrequency identification (RFID) transponder to measure ambulatory activity and temperature of individual rats when group-housed in conventional, rack-mounted home cages. The transponder location and temperature is detected by a matrix of antennae in a baseplate under the cage. An infrared high-definition camera acquires side-view video of the cage and also enables automated detection of vertical activity. Validation studies showed that baseplate-derived ambulatory activity correlated well with manual tracking and with side-view whole-cage video pixel movement. This technology enables individual behavioral and temperature data to be acquired continuously from group-housed rats in their familiar, home cage environment. We demonstrate its ability to reliably detect naturally occurring behavioral effects, extending beyond the capabilities of routine observational tests and conventional monitoring equipment. It has numerous potential applications including safety pharmacology, toxicology, circadian biology, disease models and drug discovery. PMID:28877172

System for collecting products dumped on the surface of a mass of water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carro, F.J.

1982-06-01

A system for collecting products dumped on the surface of a mass of water includes cages to be arranged at the sides of a tanker. Each cage is preferably prismatic in shape. The height of the cages is such that when the tanker is at ballast, the lower parts of the cages will be submerged while the upper parts will be above the maximum loading line of the tanker. The cages are fastened to the sides of the tanker by freely rotating connection points. In the interiors of the cages is housed a series of floating suction pump inlet membersmore » or housings, likewise prismatic in shape, having appropriate dimensions to permit a great sensitivity to the least fluctuating movements of the liquid surface. The complete face of each suction pump inlet member, which is oriented in the direction of travel of the tanker, is provided with an opening which has a height such that the lower edge thereof will be positioned below the floating line of the suction pumps at an approximate depth of 0.01 meter.« less

A favorable outcome despite a 39-hour treatment delay for arterial gas embolism: case report.

PubMed

Covington, Derek; Bielawski, Anthony; Sadler, Charlotte; Latham, Emi

2016-01-01

Cerebral arterial gas embolism (CAGE) occurs when gas enters the cerebral arterial vasculature. CAGE can occur during sitting craniotomies, cranial trauma or secondary to gas embolism from the heart. A far less common cause of CAGE is vascular entrainment of gas during endoscopic procedures. We present the case of a 49-year-old male who developed a CAGE following an esophagoduodenoscopy (EGD) biopsy. Due to a delay in diagnosis, the patient was not treated with hyperbaric oxygen (HBO₂) therapy until 39 hours after the inciting event. Despite presenting to our institution non-responsive and with decorticate posturing, the patient was eventually discharged to a rehabilitation facility, with only mild left upper extremity weakness. This delay in HBO₂ treatment represents the longest delay in treatment to our knowledge for a patient suffering from CAGE secondary to EGD. In addition to the clinical case report, we discuss the etiology of CAGE and the evidence supporting early HBO₂ treatment, as well as the data demonstrating efficacy even after considerable treatment delay. Copyright© Undersea and Hyperbaric Medical Society.

Larger cages with housing unit environment enrichment improve the welfare of marmosets.

PubMed

Yoshimoto, Takuro; Takahashi, Eiki; Yamashita, Shunji; Ohara, Kiichi; Niimi, Kimie

2018-02-09

The provision of adequate space for laboratory animals is essential not only for good welfare but accurate studies. For example, housing conditions for primates used in biomedical research may negatively affect welfare and thus the reliability of findings. In common marmosets (Callithrix jacchus), an appropriate cage size enables a socially harmonious family environment and optimizes reproductive potential. In this study, we investigated the effects of cage size on body weight (BW), behavior, and nursing succession in the common marmoset. Large cages (LCs) with environment enrichment led to an increase in BW while small cages (SCs) caused stereotypic behaviors that were not observed in LCs. In addition, the BW of infants increased with aging in LCs. Our findings indicate that the welfare of marmosets was enhanced by living in LCs. Research on non-human primates is essential for understanding the human brain and developing knowledge-based strategies for the diagnosis and treatment of psychiatric and neurological disorders. Thus, the present findings are important because they indicate that different cages may influence emotional and behavioral phenotypes.

Accelerative Forces Associated with Routine Inhouse Transportation of Rodent Cages

PubMed Central

Hurst, Keriann; Litwak, Kenneth N

2012-01-01

Transportation of rodents has repeatedly been demonstrated to potentially affect research outcomes. In addition, rapid acceleration and deceleration have marked physiologic effects. The current study determined the accelerative forces associated with common types of animal transportation within the institution and means of reducing these effects. A rodent-sized (24 g) accelerometer was placed in a standard polycarbonate mouse cage, which then was hand-carried or loaded onto a plastic, small metal, or large metal cart. The cage then moved along a set path that included several flooring types and obstacles. Accelerative forces within the mouse cage varied by as much as 35 m/s2 in as little as 1 s, primarily along the vertical axis (Z-axis). Measured acceleration was greatest with the plastic cart and lowest during hand-carrying. The placement of a towel under the cage dampened in-cage acceleration due to cart use by more than 50%, whereas a similarly located underpad had no significant effect. These data document that small rodents typically are exposed to considerable motion during transportation. The resulting physical and physiologic effects could affect study outcomes. PMID:23312081

Self-assembled nanocages based on the coiled coil bundle motif

NASA Astrophysics Data System (ADS)

Sinha, Nairiti; Villegas, Jose; Saven, Jeffery; Kiick, Kristi; Pochan, Darrin

Computational design of coiled coil peptide bundles that undergo solution phase self-assembly presents a diverse toolbox for engineering new materials with tunable and pre-determined nanostructures that can have various end applications such as in drug delivery, biomineralization and electronics. Self-assembled cages are especially advantageous as the cage geometry provides three distinct functional sites: the interior, the exterior and the solvent-cage interface. In this poster, syntheses and characterization of a peptide cage based on computationally designed homotetrameric coiled coil bundles as building blocks is discussed. Techniques such as Transmission Electron Microscopy (TEM), Small-Angle Neutron Scattering (SANS) and Analytical Ultracentrifugation (AUC) are employed to characterize the size, shape and molecular weight of the self-assembled peptide cages under different pH and temperature conditions. Various self-assembly pathways such as dialysis and thermal quenching are shown to have a significant impact on the final structure of these peptides in solution. Comparison of results with the target cage design can be used to iteratively improve the peptide design and provide greater understanding of its interactions and folding.

Isolating long-wavelength fluctuation from structural relaxation in two-dimensional glass: cage-relative displacement

NASA Astrophysics Data System (ADS)

Shiba, Hayato; Keim, Peter; Kawasaki, Takeshi

2018-03-01

It has recently been revealed that long-wavelength fluctuation exists in two-dimensional (2D) glassy systems, having the same origin as that given by the Mermin-Wagner theorem for 2D crystalline solids. In this paper, we discuss how to characterise quantitatively the long-wavelength fluctuation in a molecular dynamics simulation of a lightly supercooled liquid. We employ the cage-relative mean-square displacement (MSD), defined on relative displacement to its cage, to quantitatively separate the long-wavelength fluctuation from the original MSD. For increasing system size the amplitude of acoustic long wavelength fluctuations not only increases but shifts to later times causing a crossover with structural relaxation of caging particles. We further analyse the dynamic correlation length using the cage-relative quantities. It grows as the structural relaxation becomes slower with decreasing temperature, uncovering an overestimation by the four-point correlation function due to the long-wavelength fluctuation. These findings motivate the usage of cage-relative MSD as a starting point for analysis of 2D glassy dynamics.

Influence of strong monsoon winds on the water quality around a marine cage-culture zone in a shallow and semi-enclosed bay in Taiwan.

PubMed

Huang, Yuan-Chao Angelo; Huang, Shou-Chung; Meng, Pei-Jie; Hsieh, Hernyi Justin; Chen, Chaolun Allen

2012-04-01

Influences of marine cage culture and monsoonal disturbances, northeasterly (NE) and southwesterly (SW) monsoons on the proximal marine environment were investigated across a gradient of sites in a semi-enclosed bay, Magong Bay (Penghu Islands, Taiwan). Elevated levels of ammonia produced by the cages were the main pollutant and distinguished the cage-culture and intermediary zones (1000 m away from the cages) from the reference zone in the NE monsoon, indicating currents produced by the strong monsoon may have extended the spread of nutrient-enriched waters without necessarily flushing such effluents outside Magong Bay. Moreover, the levels of chlorophyll-a, dissolved oxygen, and turbidity were distinguishable between two seasons, suggesting that resuspension caused by the NE monsoon winds may also influence the water quality across this bay. It indicated that the impacts of marine cage culture vary as a function of distance, and also in response to seasonal movements of water driven by local climatic occurrences. Copyright © 2012 Elsevier Ltd. All rights reserved.

Automated recording of home cage activity and temperature of individual rats housed in social groups: The Rodent Big Brother project.

PubMed

Redfern, William S; Tse, Karen; Grant, Claire; Keerie, Amy; Simpson, David J; Pedersen, John C; Rimmer, Victoria; Leslie, Lauren; Klein, Stephanie K; Karp, Natasha A; Sillito, Rowland; Chartsias, Agis; Lukins, Tim; Heward, James; Vickers, Catherine; Chapman, Kathryn; Armstrong, J Douglas

2017-01-01

Measuring the activity and temperature of rats is commonly required in biomedical research. Conventional approaches necessitate single housing, which affects their behavior and wellbeing. We have used a subcutaneous radiofrequency identification (RFID) transponder to measure ambulatory activity and temperature of individual rats when group-housed in conventional, rack-mounted home cages. The transponder location and temperature is detected by a matrix of antennae in a baseplate under the cage. An infrared high-definition camera acquires side-view video of the cage and also enables automated detection of vertical activity. Validation studies showed that baseplate-derived ambulatory activity correlated well with manual tracking and with side-view whole-cage video pixel movement. This technology enables individual behavioral and temperature data to be acquired continuously from group-housed rats in their familiar, home cage environment. We demonstrate its ability to reliably detect naturally occurring behavioral effects, extending beyond the capabilities of routine observational tests and conventional monitoring equipment. It has numerous potential applications including safety pharmacology, toxicology, circadian biology, disease models and drug discovery.

Coordination-Driven Self-Assembly of M3L2 Trigonal Cages from Pre-organized Metalloligands Incorporating Octahedral Metal Centers and Fluorescent Detection of Nitroaromatics

PubMed Central

Wang, Ming; Vajpayee, Vaishali; Shanmugaraju, Sankarasekaran; Zheng, Yao-Rong; Zhao, Zhigang; Kim, Hyunuk

2011-01-01

The design and preparation of novel M3L2 trigonal cages via coordination-driven self-assembly of pre-organized metalloligands containing octahedral aluminum(III), gallium(III), or ruthenium(II) centers is described. By employing tritopic or dinuclear linear metalloligands and appropriate complementary subunits, M3L2 trigonal-bipyramidal and trigonal prismatic cages are self-assembled under mild conditions. These 3-D cages were characterized with multinuclear NMR spectroscopy (1H and 31P) and high-resolution electronic spray mass spectrometry (HR-ESI-MS). The structure of one such trigonal prismatic cage, self-assembled from an arene ruthenium metalloligand, was confirmed via single-crystal X-ray crystallography. The fluorescent nature of these prisms, due to the presence of their electron-rich ethynyl functionalities, prompted photophysical studies which revealed that electron-deficient nitroaromatics are effective quenchers of the cages' emission. Excited state charge transfer from the prisms to the nitroaromatic substrates can be used as the basis for developing selective and discriminatory turn-off fluorescent sensors for nitroaromatics. PMID:21214171

Multicomponent Gas Storage in Organic Cage Molecules

DOE PAGES

Zhang, Fei; He, Yadong; Huang, Jingsong; ...

2017-05-18

Porous liquids are a promising new class of materials featuring nanoscale cavity units dispersed in liquids that are suitable for applications such as gas storage and separation. In this work, we use molecular dynamics simulations to examine the multicomponent gas storage in a porous liquid consisting of crown-ether-substituted cage molecules dissolved in a 15-crown-5 solvent. We compute the storage of three prototypical small molecules including CO 2, CH 4, and N 2 and their binary mixtures in individual cage molecules. For porous liquids in equilibrium with a binary 1:1 gas mixture bath with partial gas pressure of 27.5 bar, amore » cage molecule shows a selectivity of 4.3 and 13.1 for the CO 2/CH 4 and CO 2/N 2 pairs, respectively. We provide a molecular perspective of how gas molecules are stored in the cage molecule and how the storage of one type of gas molecule is affected by other types of gas molecules. Finally, our results clarify the molecular mechanisms behind the selectivity of such cage molecules toward different gases.« less

Zooplankton community resilience and aquatic environmental stability on aquaculture practices: a study using net cages.

PubMed

Dias, J D; Simões, N R; Bonecker, C C

2012-02-01

Fish farming in net cages causes changes in environmental conditions. We evaluated the resilience of zooplankton concerning this activity in Rosana Reservoir (Paranapanema River, PR-SP). Samples were taken near the net cages installed at distances upstream and downstream, before and after net cage installation. The resilience was estimated by the decrease in the groups' abundance after installing the net cages. The zooplankton community was represented by 106 species. The most abundant species were Synchaeta pectinata, S. oblonga, Conochilus coenobasis, Polyarthra dolichoptera and C. unicornis (Rotifera), Ceriodaphnia cornuta, Moina minuta, Bosmina hagmanni and C. silvestrii (Cladocera) and Notodiaptomus amazonicus (Copepoda). The resilience of microcrustaceans was affected in the growing points as this activity left the production environment for longer, delaying the natural ability of community responses. Microcrustaceans groups, mainly calanoid and cyclopoid copepods, had a different return rate. The net cage installation acted as a stress factor on the zooplankton community. Management strategies that cause fewer risks to the organisms and maximize energy flow may help in maintaining system stability.

Faraday cage-type electrochemiluminescence immunosensor for ultrasensitive detection of Vibrio vulnificus based on multi-functionalized graphene oxide.

PubMed

Guo, Zhiyong; Sha, Yuhong; Hu, Yufang; Yu, Zhongqing; Tao, Yingying; Wu, Yanjie; Zeng, Min; Wang, Sui; Li, Xing; Zhou, Jun; Su, Xiurong

2016-10-01

A novel Faraday cage-type electrochemiluminescence (ECL) immunosensor devoted to the detection of Vibrio vulnificus (VV) was fabricated. The sensing strategy was presented by a unique Faraday cage-type immunocomplex based on immunomagnetic beads (IMBs) and multi-functionalized graphene oxide (GO) labeled with (2,2'-bipyridine)(5-aminophenanthroline)ruthenium (Ru-NH2). The multi-functionalized GO could sit on the electrode surface directly due to the large surface area, abundant functional groups, and good electronic transport property. It ensures that more Ru-NH2 is entirely caged and become "effective," thus improving sensitivity significantly, which resembles extending the outer Helmholtz plane (OHP) of the electrode. Under optimal conditions, the developed immunosensor achieves a limit of detection as low as 1 CFU/mL. Additionally, the proposed immunosensor with high sensitivity and selectivity can be used for the detection of real samples. The novel Faraday cage-type method has shown potential application for the diagnosis of VV and opens up a new avenue in ECL immunoassay. Graphical abstract Faraday cage-type immunoassay mode for ultrasensitive detection by extending OHP.

Multipole induced splitting of metal-cage vibrations in crystalline endohedral D2d-M2@C84 dimetallofullerenes.

PubMed

Krause, M; Popov, V N; Inakuma, M; Tagmatarchis, N; Shinohara, H; Georgi, P; Dunsch, L; Kuzmany, H

2004-01-22

Metal-carbon cage vibrations of crystalline endohedral D2d-M2@C84 (M=Sc,Y,Dy) dimetallofullerenes were analyzed by temperature dependent Raman scattering and a dynamical force field model. Three groups of metal-carbon cage modes were found at energies of 35-200 cm(-1) and assigned to metal-cage stretching and deformation vibrations. They exhibit a textbook example for the splitting of molecular vibrations in a crystal field. Induced dipole-dipole and quadrupole-quadrupole interactions account quantitatively for the observed mode splitting. Based on the metal-cage vibrational structure it is demonstrated that D2d-Y2@C84 dimetallofullerene retains a monoclinic crystal structure up to 550 K and undergoes a transition from a disordered to an ordered orientational state at a temperature of approximately 150 K.

Supracolloidal fullerene-like cages: design principles and formation mechanisms.

PubMed

Li, Zhan-Wei; Zhu, You-Liang; Lu, Zhong-Yuan; Sun, Zhao-Yan

2016-11-30

How to create novel desired structures by rational design of building blocks represents a significant challenge in materials science. Here we report a conceptually new design principle for creating supracolloidal fullerene-like cages through the self-assembly of soft patchy particles interacting via directional nonbonded interactions by mimicking non-planar sp 2 hybridized carbon atoms in C 60 . Our numerical investigations demonstrate that the rational design of patch configuration, size, and interaction can drive soft three-patch particles to reversibly self-assemble into a vast collection of supracolloidal fullerene-like cages. We further elucidate the formation mechanisms of supracolloidal fullerene-like cages by analyzing the structural characteristics and the formation process. Our results provide conceptual and practical guidance towards the experimental realization of supracolloidal fullerene-like cages, as well as a new perspective on understanding the fullerene formation mechanisms.

Porous organic cages

NASA Astrophysics Data System (ADS)

Tozawa, Tomokazu; Jones, James T. A.; Swamy, Shashikala I.; Jiang, Shan; Adams, Dave J.; Shakespeare, Stephen; Clowes, Rob; Bradshaw, Darren; Hasell, Tom; Chong, Samantha Y.; Tang, Chiu; Thompson, Stephen; Parker, Julia; Trewin, Abbie; Bacsa, John; Slawin, Alexandra M. Z.; Steiner, Alexander; Cooper, Andrew I.

2009-12-01

Porous materials are important in a wide range of applications including molecular separations and catalysis. We demonstrate that covalently bonded organic cages can assemble into crystalline microporous materials. The porosity is prefabricated and intrinsic to the molecular cage structure, as opposed to being formed by non-covalent self-assembly of non-porous sub-units. The three-dimensional connectivity between the cage windows is controlled by varying the chemical functionality such that either non-porous or permanently porous assemblies can be produced. Surface areas and gas uptakes for the latter exceed comparable molecular solids. One of the cages can be converted by recrystallization to produce either porous or non-porous polymorphs with apparent Brunauer-Emmett-Teller surface areas of 550 and 23m2g-1, respectively. These results suggest design principles for responsive porous organic solids and for the modular construction of extended materials from prefabricated molecular pores.

Termites and large herbivores influence seed removal rates in an African savanna.

PubMed

Acanakwo, Erik Francis; Sheil, Douglas; Moe, Stein R

2017-12-01

Seed removal can influence plant community dynamics, composition, and resulting vegetation characteristics. In the African savanna, termites and large herbivores influence vegetation in various ways, likely including indirect effects on seed predators and secondary dispersers. However, the intensity and variation of seed removal rates in African savannas has seldom been studied. We experimentally investigated whether termites and large herbivores were important factors in the mechanisms contributing to observed patterns in tree species composition on and off mounds, in Lake Mburo National Park, Uganda. Within fenced (excluding large herbivores) and unfenced termite mound and adjacent savanna plots, we placed seeds of nine native tree species within small open "cages," accessed by all animals, roofed cages that only allowed access to small vertebrates and invertebrates, and closed cages that permitted access by smaller invertebrates only (5 mm wire mesh). We found that mean seed removal rate was high (up to 87.3% per 3 d). Mound habitats experienced significantly higher removal rates than off-mound habitats. The mean removal rate of native seeds from closed cages was 11.1% per 3 d compared with 19.4% and 23.3% removed per 3 d in the roofed and open cages, respectively. Smaller seeds experienced higher removal rates than larger seeds. Large herbivore exclusion on mounds reduced native seed removal rates by a mean of 8.8% in the open cages, but increased removal rates by 1.7% in the open cages when off-mound habitats were fenced. While removal rates from open cages were higher on active mounds (30.9%) than on inactive mounds (26.7%), the removal rates from closed cages were lower on active vs. inactive mounds (6.1% vs. 11.6%, respectively). Thus, we conclude that large herbivores and Macrotermes mounds influence seed removal rates, though these effects appear indirect. © 2017 by the Ecological Society of America.

Comparison of Zero-profile Device Versus Plate-and-Cage Implant in the Treatment of Symptomatic Adjacent Segment Disease after Anterior Cervical Discectomy and Fusion: A Minimum 2-Year Follow-Up Study.

PubMed

Shen, Yong; Du, Wei; Wang, Lin-Feng; Dong, Zhen; Wang, Feng

2018-04-12

The purpose of this study was to compare the clinical efficacy of anterior cervical discectomy and fusion (ACDF) with Zero-profile device (Zero-p) and traditional cervical plate-and-cage implant in the treatment of symptomatic adjacent segment disease (ASD) and to determine the optimal reoperation procedure. This was a retrospective study of 58 patients with symptomatic ASD after an initial ACDF surgery and who had undergone a reoperation with ACDF with Zero-p (n = 27) and cervical plate-and-cage (n = 31) at our medical center between January 2010 and December 2015. The Japanese Orthopaedic Association score, Neck Disability Index score, Visual Analog Scale score, C2-C7 Cobb angle, and disc height index demonstrated significant improvements compared with the preoperative in both Zero-p and plate-and-cage groups (P < 0.05). However, there were no differences between the two groups (P > 0.05). The reoperation time for the Zero-p group (83.4 ± 18.9 min) was less than that for the plate-and-cage group (96.5 ± 20.1 min), with significant difference (P < 0.05). Five patients (8.6%) had cage subsidence, and 14 patients (24.1%) had dysphagia after the reoperation. There was no statistical significance in the difference between the 2 groups in cage subsidence (P > 0.05). However, the incidence of dysphagia in the plate-and-cage group (38.7%) was higher than in the Zero-p group (7.4%), with a significant difference (P < 0.05). ACDF with Zero-p obtaining the same surgical efficacy, compared with traditional cervical plate-and-cage, can significantly shorten the reoperation time and reduce the incidence of postoperative dysphagia. This option may be preferable for symptomatic patients with ASD qualifying for the anterior approach, in terms of biomechanics and surgical outcomes. Copyright © 2018 Elsevier Inc. All rights reserved.

­A practical application of reduced-copper antifouling paint in marine biological research

PubMed Central

2016-01-01

Biofouling of experimental cages and other field apparatuses can be problematic for scientists and has traditionally been addressed using frequent manual removal (e.g., scraping, scrubbing). Recent environmental restrictions and legislative changes have driven the development of less hazardous antifouling products, making antifouling paint a potential alternative option to manual removal. Consequently, the viability of using these newly developed products as a replacement for the manual cleaning of exclusion cages was experimentally investigated. There were six treatments tested, comprising three with settlement tiles in experimental cages coated with antifouling paint, two with settlement tiles in unpainted experimental cages, and one cage-free suspended tile. The three antifouling treatments comprised two reduced-copper paints (21% Cu2O and 40% Cu2O) and one copper-free, Econea™-based paint (labeled “ecofriendly”). Antifouling paints were assessed for performance of preventing fouling of the cages and whether they elicited local effects on settlement tiles contained within them. All three paints performed well to reduce fouling of the cages during the initial six weeks of the experiment, but the efficacy of “ecofriendly” paint began to decrease during an extended deployment that lasted 14 weeks. The macro-community composition, biomass, and percent cover of settled organism on tiles within cages treated with copper-based paints (21% and 40% concentrations) were indistinguishable from tiles within the manually scrubbed cages. In contrast, settlement to tiles from the “ecofriendly” treatment was different in composition of macro-community and lower in biomass, suggesting the presence of local effects and therefore rendering it unsuitable for use in settlement experiments. The results of this study suggest that reduced-copper paints have the potential to serve as an alternative to manual maintenance, which may be useful for deployments in locations that are difficult to access on a frequent schedule. PMID:27478704

Use of fly ash in diets of cage and floor broilers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pharr, C.L.; Andrews, L.D.

1980-09-01

Three experiments were conducted to compare limestone to fly ash from a coal-fired generator station as a calcium source for broilers. In experiment 1, 5 male and 5 female broiler chicks were placed in each of 32 cages. Sixteen cages of birds were fed a ration with limestone supplying 30% of the total calcium and 16 cages were fed a ration with 30% of the total calcium supplied by fly ash. The total calcium and phosphorus levels of the rations were 1.0% and .5%, respectively. In this experiment no significant difference was found for 8-week body weight between diets wheremore » the added calcium was from limestone or fly ash. In experiment 2 a group of 40 male and 40 female cage reared broilers and 40 male and 40 female floor reared broilers were fed a basal diet of limestone providing 33% of the total calcium. Three diets with increasing fly ash levels were fed to three cage groups of 40 male and 40 female broilers providing 33, 46, and 45% of the total calcium of .9, 1.1, and 1.8%, respectively. Broilers fed the highest fly ash level weighed significantly less at 8 weeks than the caged controls but did not differ from the other treatments. Bone breaking strength as measured by the Allo Kramer Shear Press was similar between the basal and low level fly ash group and increased with higher fly ash levels. In experiment 3 four groups of 40 male broilers in cages were fed limestone diets with graded levels of limestone for the calcium source. Another four groups of 40 caged male broilers were fed fly ash diets with equivalent graded levels of fly ash for the calcium source. Both limestone and fly ash diets provided .17, .34, .51, and .68% calcium of a total calcium content of .28, .45, .62, and .79%, respectively.« less

Chemically anomalous, pre-accretionally irradiated grains in interplanetary dust -- interstellar grains?. [Abstract only

NASA Technical Reports Server (NTRS)

Bradley, J. P.

1994-01-01

Ultrafine-grained matrix is a unique and fundamental building block of chondritic porous (CP) interplanetary dust particles. Most IDPs so far determined to be of cometary origin belong to the CP class. The matrix in CP IDPs is not homogeneous but rather a loose mixture of discrete single crystals (e.g., olivine, pyroxene, Fe sulfides) and polyphase grains. The petrographic diversity observed among the polyphase grains suggest that they were formed under variable physiochemical conditions. One particular class of polyphase grains are a dominant component in cometary IDPs. Although their occurrence is well documented, the terminology used to describe them is confused. They have been called many names. Here they are simply called GEMS (Glass with Embedded Metal and Sulfides). The bulk compositions of GEMS are within a factor of 3 chondritic (solar) for all major elements except C. Quantitative thin-film X-ray (EDS) analyses have shown that GEMS are systematically depleted in Mg and Si, enriched in S, Fe, and Ni, and stoichiometrically enriched in O. Electron energy-loss spectroscopy (EELS) suggests that the excess O is present as hydroxyl (-OH) groups. These same chemical 'anomalies' were observed in solar-wind-irradiated amorphous rims on the surfaces of IDPs, suggesting that the compositions of GEMS reflect prior exposure to ionizing radiation. In order to test this hypothesis, a sample of Allende (CV3) matrix was exposed to proton flux. Radiation-damaged amorphous rims on olivine and pyroxene crystals in the Allende sample were found to be depleted in Mg and Ca, enriched in S, Fe, and Ni, and stoichiometrically enriched in O. Thus, the compositions of GEMS are indeed consistent with exposure to ionizing radiation. This study suggests that chemical as well as isotopic anomalies may be used to identify presolar interstellar grains in primitive meteoritic materials.

PyMICE: APython library for analysis of IntelliCage data.

PubMed

Dzik, Jakub M; Puścian, Alicja; Mijakowska, Zofia; Radwanska, Kasia; Łęski, Szymon

2018-04-01

IntelliCage is an automated system for recording the behavior of a group of mice housed together. It produces rich, detailed behavioral data calling for new methods and software for their analysis. Here we present PyMICE, a free and open-source library for analysis of IntelliCage data in the Python programming language. We describe the design and demonstrate the use of the library through a series of examples. PyMICE provides easy and intuitive access to IntelliCage data, and thus facilitates the possibility of using numerous other Python scientific libraries to form a complete data analysis workflow.

Influence of the cage on friction torque in low loaded thrust ball bearing operating in dry conditions

NASA Astrophysics Data System (ADS)

Olaru, D.; Balan, M. R.; Tufescu, A.

2016-08-01

The authors investigated analytically and experimentally the friction torque in a modified thrust ball bearing operating at very low axial load in dry conditions by using only three balls and a cage. The experiments were conducted by using spin-down methodology. The results evidenced the influence of the sliding friction between the cage and the balls on the total friction torque. It was concluded that at very low loads the friction between cage and balls in a thrust ball bearing has an important contribution on total friction torque.

Evolution of organo-cyanometallate cages: supramolecular architectures and new Cs+-specific receptors.

PubMed

Boyer, Julie L; Kuhlman, Matthew L; Rauchfuss, Thomas B

2007-04-01

The ability of inorganic cyanometallate polymers to form interesting and useful complexes is well-known. This Account summarizes work, especially in our laboratories, aimed at replicating aspects of this inorganic chemistry in homogeneous solution using organometallic building blocks. A library of molecular organometallic cyanides and Lewis acids, with varying charges and labilities, are shown to give families of neutral and charged cages. Neutral and anionic cages, often molecular boxes, bind larger alkali metals tightly. Cubic frameworks show an unparalleled affinity for cesium cations over potassium cations. Noncubic cages are described including tetrahedranes, defect boxes, trigonal prisms, and hexagonal prisms.

Chiral Organic Cages with a Triple-Stranded Helical Structure Derived from Helicene.

PubMed

Malik, Abaid Ullah; Gan, Fuwei; Shen, Chengshuo; Yu, Na; Wang, Ruibin; Crassous, Jeanne; Shu, Mouhai; Qiu, Huibin

2018-02-28

We report the use of helicene with an intrinsic helical molecular structure to prepare covalent organic cages via imine condensation. The organic cages revealed a [3+2]-type architecture containing a triple-stranded helical structure with three helicene units arranged in a propeller-like fashion with the framework integrally twisted. Such structural chirality was retained upon dissolution in organic solvents, as indicated by a strong diastereotopy effect in proton NMR and unique Cotton effects in circular dichroism spectra. Further study on chiral adsorption showed that the chiral organic cages possess considerable enantioselectivity toward a series of aromatic racemates.

Atomistic simulations of CO2 and N2 within cage-type silica zeolites.

PubMed

Madison, Lindsey; Heitzer, Henry; Russell, Colin; Kohen, Daniela

2011-03-01

The behavior of CO(2) and N(2), both as single components and as binary mixtures, in two cage-type silica zeolites was studied using atomistic simulations. The zeolites considered, ITQ-3 and paradigm cage-type zeolite ZK4 (the all-silica analog of LTA), were chosen so that the principles illustrated can be generalized to other adsorbent/adsorbate systems with similar topology and types of interactions. N(2) was chosen both because of the potential uses of N(2)/CO(2) separations and because it differs from CO(2) most significantly in the magnitude of its Coulombic interactions with zeolites. Despite similarities between N(2) and CO(2) diffusion in other materials, we show here that the diffusion of CO(2) within cage-type zeolites is dominated by an energy barrier to diffusion located at the entrance to the narrow channels connecting larger cages. This barrier originates in Coulombic interactions between zeolites and CO(2)'s quadrupole and results in well-defined orientations for the diffusing molecules. Furthermore, CO(2)'s favorable electrostatic interactions with the zeolite framework result in preferential binding in the windows between cages. N(2)'s behavior, in contrast, is more consistent with that of molecules previously studied. Our analysis suggests that CO(2)'s behavior might be common for adsorbates with quadrupoles that interact strongly with a material that has narrow windows between cages.

Infections of nervous necrosis virus in wild and cage-reared marine fish from South China Sea with unexpected wide host ranges.

PubMed

Liu, X D; Huang, J N; Weng, S P; Hu, X Q; Chen, W J; Qin, Z D; Dong, X X; Liu, X L; Zhou, Y; Asim, M; Wang, W M; He, J G; Lin, L

2015-06-01

The concerns about the impact of the nervous necrosis virus (NNV) infections in wild fish have been raised. This paper presents the results of quarterly surveys of NNV in wild and cage-reared marine fish from South China Sea. Samples of 892 wild fish belonging to 69 species and 381 cage-reared fish belonging to 11 species were collected and were detected by seminested PCR and nested PCR. In the case of seminested PCR, the positive signal was detected in 3.0% and 3.1% samples of wild and cage-reared fish, respectively. However, by nested RT-PCR, the positive signal was observed in 42.3% and 63.0% samples of wild and cage-reared fish, respectively. If the fish species were considered, the positive signal was detected in 21.7% and 72.7% species of wild and cage-reared fish by seminested PCR assay, respectively. However, by nested RT-PCR, the positive signal was observed in 65.2% and 100% species of wild and cage-reared fish, respectively. The nucleotide sequences of the nested PCR products were determined. Phylogenetic tree showed that all the obtained viral isolates belonged to the red-spotted grouper nervous necrosis virus (RGNNV) genotype. Thirty-five species of the marine fish were the new hosts of NNV. © 2014 John Wiley & Sons Ltd.

Cross-Cultural Adaptation and Psychometric Properties of the AUDIT and CAGE Questionnaires in Tanzanian Swahili for a Traumatic Brain Injury Population.

PubMed

Vissoci, Joao Ricardo Nickenig; Hertz, Julian; El-Gabri, Deena; Andrade Do Nascimento, José Roberto; Pestillo De Oliveira, Leonardo; Mmbaga, Blandina Theophil; Mvungi, Mark; Staton, Catherine A

2018-01-01

To develop Swahili versions of the Alcohol Use Disorders Identification Test (AUDIT) and CAGE questionnaires and evaluate their psychometric properties in a traumatic brain injury (TBI) population in Tanzania. Swahili versions of the AUDIT and CAGE were developed through translation and back-translation by a panel of native speakers of both English and Swahili. The translated instruments were administered to a sample of Tanzanian adults from a TBI registry. The validity and reliability were analyzed using standard statistical methods. The translated versions of both the AUDIT and CAGE questionnaires were found to have excellent language clarity and domain coherence. Reliability was acceptable (>0.85) for all tested versions. Confirmatory factor analysis of one, two and three factor solution for the AUDIT and one factor solution for the CAGE showed adequate results. AUDIT and CAGE scores were strongly correlated to each other (R > 0.80), and AUDIT scores were significantly lower in non-drinkers compared to drinkers. This article presents the first Swahili and Tanzanian adaptations of the AUDIT and CAGE instruments as well as the first validation of these questionnaires with TBI patients. Both instruments were found to have acceptable psychometric properties, resulting in two new useful tools for medical and social research in this setting. © The Author 2017. Medical Council on Alcohol and Oxford University Press. All rights reserved.

Comparison of Performance of Experimental and Conventional Cage Designs and Materials for 75-millimeter-bore Cylindrical Roller Bearings at High Speed

NASA Technical Reports Server (NTRS)

Anderson, William J; Macks, E Fred; Nemeth, Zolton N

1954-01-01

The results of two investigations, one to determine the relative merits of four experimental and two conventional design 75-millimeter-bore (size 215) cylindrical roller bearings and one to determine the relative merits of nodular iron and bronze as cage materials for this size and type of bearing, are presented in this report. Nine test bearings were operated over a range of dn values (product of bearing bore in mm and shaft speed in r.p.m) from 0.3 x 10(6) to 2.3 x 20(6), radial loads for 7 to 1613 pounds, and oil flows from 2 to 8 pounds per minute with a single-jet circulatory oil feed. Of the six bearings used to evaluate designs, four were experimental types with outer-race-riding cages and inner-race-guided rollers, and two were conventional types, one with outer-race-guided rollers and cage and one with inner-race-guided rollers and cage. Each of these six test bearings was equipped with a different design cage made of nodular iron. The experimental combination of an outer-race-riding cage with a straight-through outer race and inner-race-guided rollers was found to give the best over-all performance based on limiting dn values and bearing temperatures.

Optimized FPGA Implementation of Multi-Rate FIR Filters Through Thread Decomposition

NASA Technical Reports Server (NTRS)

Kobayashi, Kayla N.; He, Yutao; Zheng, Jason X.

2011-01-01

Multi-rate finite impulse response (MRFIR) filters are among the essential signal-processing components in spaceborne instruments where finite impulse response filters are often used to minimize nonlinear group delay and finite precision effects. Cascaded (multistage) designs of MRFIR filters are further used for large rate change ratio in order to lower the required throughput, while simultaneously achieving comparable or better performance than single-stage designs. Traditional representation and implementation of MRFIR employ polyphase decomposition of the original filter structure, whose main purpose is to compute only the needed output at the lowest possible sampling rate. In this innovation, an alternative representation and implementation technique called TD-MRFIR (Thread Decomposition MRFIR) is presented. The basic idea is to decompose MRFIR into output computational threads, in contrast to a structural decomposition of the original filter as done in the polyphase decomposition. A naive implementation of a decimation filter consisting of a full FIR followed by a downsampling stage is very inefficient, as most of the computations performed by the FIR state are discarded through downsampling. In fact, only 1/M of the total computations are useful (M being the decimation factor). Polyphase decomposition provides an alternative view of decimation filters, where the downsampling occurs before the FIR stage, and the outputs are viewed as the sum of M sub-filters with length of N/M taps. Although this approach leads to more efficient filter designs, in general the implementation is not straightforward if the numbers of multipliers need to be minimized. In TD-MRFIR, each thread represents an instance of the finite convolution required to produce a single output of the MRFIR. The filter is thus viewed as a finite collection of concurrent threads. Each of the threads completes when a convolution result (filter output value) is computed, and activated when the first input of the convolution becomes available. Thus, the new threads get spawned at exactly the rate of N/M, where N is the total number of taps, and M is the decimation factor. Existing threads retire at the same rate of N/M. The implementation of an MRFIR is thus transformed into a problem to statically schedule the minimum number of multipliers such that all threads can be completed on time. Solving the static scheduling problem is rather straightforward if one examines the Thread Decomposition Diagram, which is a table-like diagram that has rows representing computation threads and columns representing time. The control logic of the MRFIR can be implemented using simple counters. Instead of decomposing MRFIRs into subfilters as suggested by polyphase decomposition, the thread decomposition diagrams transform the problem into a familiar one of static scheduling, which can be easily solved as the input rate is constant.

Self-Assembly, Guest Capture, and NMR Spectroscopy of a Metal-Organic Cage in Water

ERIC Educational Resources Information Center

Go, Eun Bin; Srisuknimit, Veerasak; Cheng, Stephanie L.; Vosburg, David A.

2016-01-01

A green organic-inorganic laboratory experiment has been developed in which students prepare a self-assembling iron cage in D[subscript 2]O at room temperature. The tetrahedral cage captures a small, neutral molecule such as cyclohexane or tetrahydrofuran. [Superscript 1]H NMR analysis distinguishes captured and free guests through diagnostic…

A generic strategy for pharmacological caging of growth factors for tissue engineering.

PubMed

Karlsson, Maria; Lienemann, Philipp S; Sprossmann, Natallia; Heilmann, Katharina; Brummer, Tilman; Lutolf, Matthias P; Ehrbar, Martin; Weber, Wilfried

2013-07-07

The caging of small molecules has revolutionized biological research by providing a means to regulate a wide range of processes. Here we report on a generic pharmacological method to cage proteins in a similar fashion. The present approach is of value in both fundamental and applied research, e.g. in tissue engineering.

Teaching in the Institutional Cage: Metaphor and Collateral Oppression

ERIC Educational Resources Information Center

Noël Smith, Becky L.

2014-01-01

This analysis is a philosophical exploration of Marilyn Frye's metaphor of the cage and Patricia Hill Collins' theory of intersecting oppressions. It argues that social structures and forms of oppressive knowledge make up the individual wires on each person's cage and that these work to confine individuals, particularly those in the…

Cryogenic Caging for Science Instrumentation

NASA Technical Reports Server (NTRS)

Penanen, Konstantin; Chui, Talso C.

2011-01-01

A method has been developed for caging science instrumentation to protect from pyro-shock and EDL (entry, descent, and landing) acceleration damage. Caging can be achieved by immersing the instrument (or its critical parts) in a liquid and solidifying the liquid by cooling. After the launch shock and/or after the payload has landed, the solid is heated up and evaporated.

Bio-Inspired Nanomaterials: Protein Cage Nano-Architectures

DTIC Science & Technology

2008-04-01

chemical modification of protein cage materials and controlled chemical synthesis under mild biological conditions. High- resolution structural...properties based on a combination of controlled mobility and metal ligand interactions. Using the exterior surface of the CCMV viral cage we have chemically ...follows: Patterning by microplotter was achieved by depositing a preselected antibody solution directly onto chemically activated silicon or gold

An unprecedented Fe(36) phosphonate cage.

PubMed

Beavers, Christine M; Prosvirin, Andrey V; Prosverin, Andrey V; Cashion, John D; Dunbar, Kim R; Richards, Anne F

2013-02-18

The reaction of 2-pyridylphosphonic acid (LH(2)) with iron(II) perchlorate and iron(III) nitrate afforded an interconnected, double-layered, cationic iron cage, [{Fe(36)L(44)(H(2)O)(48)}](20+) (1a), the largest interconnected, polynuclear ferric cage reported to date. Magnetic studies on 1a revealed antiferromagnetic coupling between the spins on adjacent Fe(III) ions.

The effect of perch availability during pullet rearing and egg laying on the behavior of caged White Leghorn hens

USDA-ARS?s Scientific Manuscript database

Enriched cages, compared to conventional cages, allow egg laying strains of chickens to meet some behavioral needs, including the high motivation to perch. The objective of this study was to determine if perch availability during rearing affected perch use as adults and if perch presence affected ea...

Spray washing, absorbent corn starch powder and dry time to reduce bacterial numbers on soiled boiler transport cage flooring

USDA-ARS?s Scientific Manuscript database

Most broilers in the U.S. are transported live to slaughter facilities in cages with fiberglass floors. Cages are often used repeatedly without washing and fecal matter deposited on the floor surface can transfer Campylobacter from one flock to another. Drying feces out between uses is an effectiv...

Potential for horizontal transmission of Salmonella and Campylobacter among caged and cage free laying hens

USDA-ARS?s Scientific Manuscript database

Nine hens were inoculated orally and intravaginally with a marker strain of Salmonella and Campylobacter at 56 wk-of-age and housed in individual cages in isolation. Challenged hens were comingled with non-challenged hens 2 wk post-inoculation, at a ratio of 1 challenged hen per 4 non-challenged he...

TACOM LCMC IB and DMSMS Mitigation

DTIC Science & Technology

2011-09-26

Sources I Gosed II Opened ~ I AAC flag: Vii6d AI CAGE codes (CONUS): 3 3 CAGE codes (OCONUS): 0 0 ---- Total: 3 3 Single or no CAGE code...v In box - I’lL- I Qi) chambers:... I ~ Microsoft - I I~ AADO SER.- t@) ~ i_ .... gose I I Used On Reference/Part Numbers I~ 26SEP11

Depopulation of Caged Layer Hens with a Compressed Air Foam System

PubMed Central

Gurung, Shailesh; Hoffman, John; Stringfellow, Kendre; Abi-Ghanem, Daad; Zhao, Dan; Caldwell, David; Lee, Jason; Styles, Darrel; Berghman, Luc; Byrd, James; Farnell, Yuhua; Archer, Gregory

2018-01-01

Simple Summary Reportable diseases, such as avian influenza, spread rapidly among poultry, resulting in the death of a large number of birds. Once such a disease has been diagnosed at a farm, infected and susceptible birds are rapidly killed to prevent the spread of the disease. The methods to eliminate infected caged laying hens are limited. An experiment was conducted to study the effectiveness of foam made from compressed air, water, and soap to kill laying hens in cages. The study found that stress levels of the hens killed using compressed air foam in cages to be similar to the hens killed by carbon dioxide or the negative control. Hens exposed to carbon dioxide died earlier as compared to the foam methods. The authors conclude that application of compressed air foam in cages is an alternative to methods such as gas inhalation and ventilation shutdown to rapidly and humanely kill laying hens during epidemics. Abstract During the 2014–2015 US highly pathogenic avian influenza (HPAI) outbreak, 50.4 million commercial layers and turkeys were affected, resulting in economic losses of $3.3 billion. Rapid depopulation of infected poultry is vital to contain and eradicate reportable diseases like HPAI. The hypothesis of the experiment was that a compressed air foam (CAF) system may be used as an alternative to carbon dioxide (CO2) inhalation for depopulating caged layer hens. The objective of this study was to evaluate corticosterone (CORT) and time to cessation of movement (COM) of hens subjected to CAF, CO2 inhalation, and negative control (NEG) treatments. In Experiment 1, two independent trials were conducted using young and spent hens. Experiment 1 consisted of five treatments: NEG, CO2 added to a chamber, a CO2 pre-charged chamber, CAF in cages, and CAF in a chamber. In Experiment 2, only spent hens were randomly assigned to three treatments: CAF in cages, CO2 added to a chamber, and aspirated foam. Serum CORT levels of young hens were not significantly different among the CAF in cages, CAF in a chamber, NEG control, and CO2 inhalation treatments. However, spent hens subjected to the CAF in a chamber had significantly higher CORT levels than birds in the rest of the treatments. Times to COM of spent hens subjected to CAF in cages and aspirated foam were significantly greater than of birds exposed to the CO2 in a chamber treatment. These data suggest that applying CAF in cages is a viable alternative for layer hen depopulation during a reportable disease outbreak. PMID:29324639

PCR Testing of IVC Filter Tops as a Method for Detecting Murine Pinworms and Fur Mites.

PubMed

Gerwin, Philip M; Ricart Arbona, Rodolfo J; Riedel, Elyn R; Henderson, Kenneth S; Lipman, Neil S

2017-11-01

We evaluated PCR testing of filter tops from cages maintained on an IVC system through which exhaust air is filtered at the cage level as a method for detecting parasite-infected and -infested cages. Cages containing 4 naïve Swiss Webster mice received 360 mL of uncontaminated aspen chip or α-cellulose bedding (n = 18 cages each) and 60 mL of the same type of bedding weekly from each of the following 4 groups of cages housing mice infected or infested with Syphacia obvelata (SO), Aspiculuris tetraptera (AT), Myocoptes musculinus (MC), or Myobia musculi (MB) and Radfordia affinis (RA; 240 mL bedding total). Detection rates were compared at 30, 60, and 90 d after initiating bedding exposure, by using PCR analysis of filter tops (media extract and swabs) and testing of mouse samples (fur swab [direct] PCR testing, fecal flotation, anal tape test, direct examination of intestinal contents, and skin scrape). PCR testing of filter media extract detected 100% of all parasites at 30 d (both bedding types) except for AT (α-cellulose bedding, 67% detection rate); identified more cages with fur mites (MB and MC) than direct PCR when cellulose bedding was used; and was better at detecting parasites than all nonmolecular methods evaluated. PCR analysis of filter media extract was superior to swab and direct PCR for all parasites cumulatively for each bedding type. Direct PCR more effectively detected MC and all parasites combined for aspen chip compared with cellulose bedding. PCR analysis of filter media extract for IVC systems in which exhaust air is filtered at the cage level was shown to be a highly effective environmental testing method.

Biomechanical advantages of supplemental accessory and satellite rods with and without interbody cages implantation for the stabilization of pedicle subtraction osteotomy.

PubMed

La Barbera, Luigi; Brayda-Bruno, Marco; Liebsch, Christian; Villa, Tomaso; Luca, Andrea; Galbusera, Fabio; Wilke, Hans-Joachim

2018-05-08

To investigate the effect of anterior interbody cages, accessory and satellite rods usage on primary stability and rod strains for PSO stabilization. Seven human cadaveric spine segments (T12-S1) underwent PSO at L4 with posterior fixation from L2 to S1. In vitro flexibility tests were performed under pure moments in flexion/extension (FE), lateral bending (LB) and axial rotation (AR) to determine the range of motion, while measuring the strains on the primary rods with strain gauge rosettes. Six constructs with 2, 3 and 4 rods, with and without interbody cages implantation adjacent to the PSO site, were compared. All constructs had comparable effects in reducing spine kinematics compared to the intact condition (- 94% in FE and LB; - 80% in AR). Supplementation of 2 rods with lateral accessory rods (4 rods) was the most effective strategy in minimizing primary rod strains, particularly when coupled to cages (p ≤ 0.005; - 50% in FE, - 42% in AR and - 11% in LB); even without cages, the strains were significantly reduced (p ≤ 0.009; - 26%, - 37%, - 9%). The addition of a central satellite rod with laminar hooks (3 rods) effectively reduced rod strains in FE (p ≤ 0.005; - 30%) only in combination with cages. The study supports the current clinical practice providing a strong biomechanical rationale to recommend 4-rod constructs based on accessory rods combined with cages adjacent to PSO site. Although weaker, the usage of accessory rods without cages and of a central satellite rod with hooks in combination with interbody spacers may also be justified. These slides can be retrieved under Electronic Supplementary Material.

Reducing Mouse Anxiety during Handling: Effect of Experience with Handling Tunnels

PubMed Central

Gouveia, Kelly; Hurst, Jane L.

2013-01-01

Handling stress is a well-recognised source of variation in animal studies that can also compromise the welfare of research animals. To reduce background variation and maximise welfare, methods that minimise handling stress should be developed and used wherever possible. Recent evidence has shown that handling mice by a familiar tunnel that is present in their home cage can minimise anxiety compared with standard tail handling. As yet, it is unclear whether a tunnel is required in each home cage to improve response to handling. We investigated the influence of prior experience with home tunnels among two common strains of laboratory mice: ICR(CD-1) and C57BL/6. We compared willingness to approach the handler and anxiety in an elevated plus maze test among mice picked up by the tail, by a home cage tunnel or by an external tunnel shared between cages. Willingness to interact with the handler was much greater for mice handled by a tunnel, even when this was unfamiliar, compared to mice picked up by the tail. Once habituated to handling, C57BL/6 mice were most interactive towards a familiar home tunnel, whereas the ICR strain showed strong interaction with all tunnel handling regardless of any experience of a home cage tunnel. Mice handled by a home cage or external tunnel showed less anxiety in an elevated plus maze than those picked up by the tail. This study shows that using a tunnel for routine handling reduces anxiety among mice compared to tail handling regardless of prior familiarity with tunnels. However, as home cage tunnels can further improve response to handling in some mice, we recommend that mice are handled with a tunnel provided in their home cage where possible as a simple practical method to minimise handling stress. PMID:23840458

Reducing mouse anxiety during handling: effect of experience with handling tunnels.

PubMed

Gouveia, Kelly; Hurst, Jane L

2013-01-01

Handling stress is a well-recognised source of variation in animal studies that can also compromise the welfare of research animals. To reduce background variation and maximise welfare, methods that minimise handling stress should be developed and used wherever possible. Recent evidence has shown that handling mice by a familiar tunnel that is present in their home cage can minimise anxiety compared with standard tail handling. As yet, it is unclear whether a tunnel is required in each home cage to improve response to handling. We investigated the influence of prior experience with home tunnels among two common strains of laboratory mice: ICR(CD-1) and C57BL/6. We compared willingness to approach the handler and anxiety in an elevated plus maze test among mice picked up by the tail, by a home cage tunnel or by an external tunnel shared between cages. Willingness to interact with the handler was much greater for mice handled by a tunnel, even when this was unfamiliar, compared to mice picked up by the tail. Once habituated to handling, C57BL/6 mice were most interactive towards a familiar home tunnel, whereas the ICR strain showed strong interaction with all tunnel handling regardless of any experience of a home cage tunnel. Mice handled by a home cage or external tunnel showed less anxiety in an elevated plus maze than those picked up by the tail. This study shows that using a tunnel for routine handling reduces anxiety among mice compared to tail handling regardless of prior familiarity with tunnels. However, as home cage tunnels can further improve response to handling in some mice, we recommend that mice are handled with a tunnel provided in their home cage where possible as a simple practical method to minimise handling stress.

Salmonella spp. and Extended-Spectrum Cephalosporin-Resistant Escherichia coli Frequently Contaminate Broiler Chicken Transport Cages of an Organic Production Company.

PubMed

Mollenkopf, Dixie F; De Wolf, Brittany; Feicht, Sydnee M; Cenera, Johana K; King, Christy A; van Balen, Joany C; Wittum, Thomas E

2018-06-06

Antimicrobial resistant bacteria in retail meat pose a health hazard to the public, as does contamination of these products with Salmonella. Our aim was to determine the prevalence of Salmonella as well as Escherichia coli expressing AmpC and extended-spectrum beta-lactamase (ESBL) resistance phenotypes contaminating broiler transport cages and fresh, retail ground chicken meat. Sterile gauze sponges were used to collect duplicate cage floor samples from transport trailers that deliver market-ready birds to a single organic poultry-processing facility. With the exception of the first visit (n = 25), 50 duplicate cage floor samples were collected using moistened sterile gauze sponges on each of nine weekly visits during May, June, and July 2013. Additionally, fresh, retail ground chicken meat was sampled at each weekly visit from an on-site retail store located at the same processing facility. A total of 425 cage swabs and 72 ground chicken aliquots from 24 retail packages were collected and screened for the presence of Salmonella as well as E. coli expressing resistance to extended-spectrum cephalosporins using selective culture. We recovered Salmonella from 26.1% of cage swab samples and 2.8% of retail meat samples. E. coli expressing AmpC and ESBL resistance phenotypes were recovered from 84.9% and 22.6% of cage swabs and 77.8% and 11.1% of fresh, retail ground meat samples, respectively. Our results suggest that transport cages could potentially act as a source of broiler exposure to both Salmonella and enteric bacteria resistant to important antimicrobial drugs as they are transported for entry into the food supply as fresh, retail meat products.

Validity of the CAGE questionnaire for men who have sex with men (MSM) in China.

PubMed

Chen, Yen-Tyng; Ibragimov, Umedjon; Nehl, Eric J; Zheng, Tony; He, Na; Wong, Frank Y

2016-03-01

Detection of heavy drinking among men who have sex with men (MSM) is crucial for both intervention and treatment. The CAGE questionnaire is a popular screening instrument for alcohol use problems. However, the validity of CAGE for Chinese MSM is unknown. Data were from three waves of cross-sectional assessments among general MSM (n=523) and men who sell sex to other men ("money boys" or MBs, n=486) in Shanghai, China. Specifically, participants were recruited using respondent-driven, community popular opinion leader, and venue-based sampling methods. The validity of the CAGE was examined for different cutoff scores and individual CAGE items using self-reported heavy drinking (≥14 drinks in the past week) as a criterion. In the full sample, 75 (7.4%) of participants were classified as heavy drinkers. 32 (6.1%) of general MSM and 43 (8.9%) of MBs were heavy drinkers. The area under curve statistics for overall sample was 0.7 (95% CI: 0.36-0.77). Overall, the sensitivities (ranging from 18.7 to 66.7%), specificities (ranging from 67.5 to 95.8%), and positive predictive values (ranging from 14.1 to 26.4%) for different cutoff scores were inadequate using past week heavy drinking as the criterion. The ability of CAGE to discriminate heavy drinkers from non-heavy drinkers was limited. Our findings showed the inadequate validity of CAGE as a screening instrument for current heavy drinking in Chinese MSM. Further research using a combination of validity criteria is needed to determine the applicability of CAGE for this population. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Effect of Spectral Transmittance through Red-Tinted Rodent Cages on Circadian Metabolism and Physiology in Nude Rats

PubMed Central

Dauchy, Robert T; Wren, Melissa A; Dauchy, Erin M; Hanifin, John P; Jablonski, Michael R; Warfield, Benjamin; Brainard, George C; Hill, Steven M; Mao, Lulu; Dupepe, Lynell M; Ooms, Tara G; Blask, David E

2013-01-01

Light entrains normal circadian rhythms of physiology and metabolism in all mammals. Previous studies from our laboratory demonstrated that spectral transmittance (color) of light passing through cages affects these responses in rats. Here, we addressed the hypothesis that red tint alters the circadian nocturnal melatonin signal and circadian oscillation of other metabolic and physiologic functions. Female nude rats (Hsd:RH-Foxn1rnu; n = 12 per group) were maintained on a 12:12-h light (300 lx; 123.0 μW/cm2; lights on 0600):dark regimen in standard polycarbonate translucent clear or red-tinted cages. After 1 wk, rats underwent 6 low-volume blood draws via cardiocentesis over a 4-wk period. Plasma melatonin levels were low during the light phase (1.0 ± 0.2 pg/mL) in rats in both types of cages but were significantly lower in red-tinted (105.0 ± 2.4 pg/mL) compared with clear (154.8 ± 3.8 pg/mL) cages during the dark. Normal circadian rhythm of plasma total fatty acid was identical between groups. Although phase relationships of circadian rhythms in glucose, lactic acid, pO2, and pCO2 were identical between groups, the levels of these analytes were lower in rats in red-tinted compared with clear cages. Circadian rhythms of plasma corticosterone, insulin, and leptin were altered in terms of phasing, amplitude, and duration in rats in red-tinted compared with clear cages. These findings indicate that spectral transmittance through red-colored cages significantly affects circadian regulation of neuroendocrine, metabolic, and physiologic parameters, potentially influencing both laboratory animal health and wellbeing and scientific outcomes. PMID:24351763

Field cage studies and progressive evaluation of genetically-engineered mosquitoes.

PubMed

Facchinelli, Luca; Valerio, Laura; Ramsey, Janine M; Gould, Fred; Walsh, Rachael K; Bond, Guillermo; Robert, Michael A; Lloyd, Alun L; James, Anthony A; Alphey, Luke; Scott, Thomas W

2013-01-01

A genetically-engineered strain of the dengue mosquito vector Aedes aegypti, designated OX3604C, was evaluated in large outdoor cage trials for its potential to improve dengue prevention efforts by inducing population suppression. OX3604C is engineered with a repressible genetic construct that causes a female-specific flightless phenotype. Wild-type females that mate with homozygous OX3604C males will not produce reproductive female offspring. Weekly introductions of OX3604C males eliminated all three targeted Ae. aegypti populations after 10-20 weeks in a previous laboratory cage experiment. As part of the phased, progressive evaluation of this technology, we carried out an assessment in large outdoor field enclosures in dengue endemic southern Mexico. OX3604C males were introduced weekly into field cages containing stable target populations, initially at 10:1 ratios. Statistically significant target population decreases were detected in 4 of 5 treatment cages after 17 weeks, but none of the treatment populations were eliminated. Mating competitiveness experiments, carried out to explore the discrepancy between lab and field cage results revealed a maximum mating disadvantage of up 59.1% for OX3604C males, which accounted for a significant part of the 97% fitness cost predicted by a mathematical model to be necessary to produce the field cage results. Our results indicate that OX3604C may not be effective in large-scale releases. A strain with the same transgene that is not encumbered by a large mating disadvantage, however, could have improved prospects for dengue prevention. Insights from large outdoor cage experiments may provide an important part of the progressive, stepwise evaluation of genetically-engineered mosquitoes.

PCR Testing of IVC Filter Tops as a Method for Detecting Murine Pinworms and Fur Mites

PubMed Central

Gerwin, Philip M; Arbona, Rodolfo J Ricart; Riedel, Elyn R; Henderson, Kenneth S; Lipman, Neil S

2017-01-01

We evaluated PCR testing of filter tops from cages maintained on an IVC system through which exhaust air is filtered at the cage level as a method for detecting parasite- infected and -infested cages. Cages containing 4 naïve Swiss Webster mice received 360 mL of uncontaminated aspen chip or α-cellulose bedding (n = 18 cages each) and 60 mL of the same type of bedding weekly from each of the following 4 groups of cages housing mice infected or infested with Syphacia obvelata (SO), Aspiculuris tetraptera (AT), Myocoptes musculinus (MC), or Myobia musculi (MB) and Radfordia affinis (RA; 240 mL bedding total). Detection rates were compared at 30, 60, and 90 d after initiating bedding exposure, by using PCR analysis of filter tops (media extract and swabs) and testing of mouse samples (fur swab [direct] PCR testing, fecal flotation, anal tape test, direct examination of intestinal contents, and skin scrape). PCR testing of filter media extract detected 100% of all parasites at 30 d (both bedding types) except for AT (α-cellulose bedding, 67% detection rate); identified more cages with fur mites (MB and MC) than direct PCR when cellulose bedding was used; and was better at detecting parasites than all nonmolecular methods evaluated. PCR analysis of filter media extract was superior to swab and direct PCR for all parasites cumulatively for each bedding type. Direct PCR more effectively detected MC and all parasites combined for aspen chip compared with cellulose bedding. PCR analysis of filter media extract for IVC systems in which exhaust air is filtered at the cage level was shown to be a highly effective environmental testing method. PMID:29256370

General and simple approach for control cage and cylindrical mesopores, and thermal/hydrothermal stable frameworks.

PubMed

El-Safty, Sherif A; Mizukami, Fujio; Hanaoka, Takaaki

2005-05-19

Highly ordered cage and cylindrical mesoporeous silica monoliths (HOM) with 2- and 3-dimensional (2D and 3D, respectively) structures, mesopore/micropore volumes, and thick-walled frameworks were successfully fabricated by instant direct templating of lyotropic phases of copolymer (EO(m)-PO(n)-EO(m)) surfactants. Large cage-like pores with uniform constriction sizes up to 10 nm and open cylindrical channel-like mesopores can be easily achieved by this simple and efficient synthesis design. Our results show that the cage-like pores could be fabricated at relatively lower copolymer concentrations used in the lyotropic phase domains at copolymer/TMOS ratios of 35 wt %. These ordered cage pore architectures underwent transition to open-cylindrical pores by increasing the copolymer concentration. High EO/PO block copolymers, in general, were crucially affected on the increase of the interior cavity sizes and on the stability of the cage mesopore characters. However, for F108 (EO(141)PO(44)EO(141)) systems, the fabrication of ordered and stable cage pore monoliths was achieved with significantly higher copolymer concentrations up to 90 wt %. Interestingly, the effective copolymer molecular nature was also observed in the ability to design various ordered mesophase geometries in large domain sizes. Our findings here show evidence that the synthetic strategy provides realistic control over a wide range of mesostructured phase geometries and their extended long-range ordering in the final replicas of the silica monolith frameworks. In addition, the HOM silica monoliths exhibited considerable structural stability against higher thermal temperature (up to 1000 degrees C) and longer hydrothermal treatment times under boiling water and steam. The remarkable structural findings of 3D frameworks, transparent monoliths, and micropores combined with large cage- and cylindrical-like mesopores are expected to find promising uses in materials chemistry.

Social influences on morphine conditioned place preference in adolescent mice.

PubMed

Cole, Shannon L; Hofford, Rebecca S; Evert, Daniel J; Wellman, Paul J; Eitan, Shoshana

2013-03-01

Social/peer influences are among the strongest predictors of adolescent drug use. However, this important subject does not get much attention in pre-clinical studies. We recently observed that exposure to different social partners modulates morphine locomotor sensitization. Sensitivity to the hyper-locomotor response of drugs of abuse is a predictor of sensitivity to other drug-induced behaviors. Thus, this study examined how exposure to different social partners affected the rewarding properties of morphine. All animals were group-housed four per cage in one of two conditions referred to as 'only' and 'cage-mates'. In the mixed treatment condition, morphine- and saline-treated mice were housed together. These groups are referred to as 'morphine cage-mates' and 'saline cage-mates', respectively. In the separated treatment conditions, all mice in the cage received morphine (i.e. 'morphine only') or saline (i.e. 'saline only'), and cages were visually separated from each other. All animals were subsequently individually tested for the acquisition of morphine conditioned place preference (CPP) following one conditioning session with 10, 20 or 40 mg/kg morphine or saline. As expected, one conditioning session established morphine CPP in the morphine only animals, but not in the saline only animals. Notably, morphine CPP was not acquired by the morphine cage-mate animals. Additionally, 40 mg/kg morphine was sufficient to establish morphine CPP in the saline cage-mate animals. These results indicate that social environment has an effect on the rewarding properties of morphine. It suggests that exposure to different peers can alter the abuse potential of opioids and potentially other illicit drugs. © 2012 The Authors, Addiction Biology © 2012 Society for the Study of Addiction.

Application of titanium and polyetheretherketone cages in the treatment of pyogenic spondylodiscitis.

PubMed

Schomacher, Markus; Finger, Tobias; Koeppen, Daniel; Süss, Olaf; Vajkoczy, Peter; Kroppenstedt, Stefan; Cabraja, Mario

2014-12-01

Surgical treatment of a pyogenic spondylodiscitis (PSD) involves a fixation and debridement of the affected segment combined with a specific antibiotic therapy. To achieve a proper stability and to avoid pseudarthrosis and kyphotic malposition many surgeons favour the interposition of an anterior graft. Besides autologous bone grafts titanium (TTN) cages have gained acceptance in the treatment of PSD. Polyetheretherketone (PEEK) cages have a more favourable modulus of elasticity than TTN. We compared both cage types. Primary endpoints were the rate of reinfection and radiological results. From 2004 to 2013 51 patients underwent surgery for PSD with fixation and TTN or PEEK cage-implantation. While lumbar patients underwent a partial discectomy by the posterior approach, discs of the cervical and thoracic patients had been totally removed from anterior. Clinical and radiological parameters were assessed in 37 eligible patients after a mean of 20.4 months. 21 patients received a PEEK- and 16 patients a TTN-cage. A reinfection after surgery and 3 months of antibiotic therapy was not observed. Solid arthrodesis was found in 90.5% of the PEEK-group and 100% of the TTN-group. A segmental correction could be achieved in both groups. Nonetheless, a cage subsidence was observed in 70.3% of all cases. Comparison of radiological results revealed no differences between both groups. A debridement and fixation with anterior column support in combination with an antibiotic therapy appear to be the key points for successful treatment of PSD. The application of TTN- or PEEK-cages does not appear to influence the radiological outcome or risk of reinfection, neither does the extent of disc removal in this clinical subset. Copyright © 2014 Elsevier B.V. All rights reserved.

Molecular dynamics study of structure H clathrate hydrates of methane and large guest molecules.

PubMed

Susilo, Robin; Alavi, Saman; Ripmeester, John A; Englezos, Peter

2008-05-21

Methane storage in structure H (sH) clathrate hydrates is attractive due to the relatively higher stability of sH as compared to structure I methane hydrate. The additional stability is gained without losing a significant amount of gas storage density as happens in the case of structure II (sII) methane clathrate. Our previous work has showed that the selection of a specific large molecule guest substance (LMGS) as the sH hydrate former is critical in obtaining the optimum conditions for crystallization kinetics, hydrate stability, and methane content. In this work, molecular dynamics simulations are employed to provide further insight regarding the dependence of methane occupancy on the type of the LMGS and pressure. Moreover, the preference of methane molecules to occupy the small (5(12)) or medium (4(3)5(6)6(3)) cages and the minimum cage occupancy required to maintain sH clathrate mechanical stability are examined. We found that thermodynamically, methane occupancy depends on pressure but not on the nature of the LMGS. The experimentally observed differences in methane occupancy for different LMGS may be attributed to the differences in crystallization kinetics and/or the nonequilibrium conditions during the formation. It is also predicted that full methane occupancies in both small and medium clathrate cages are preferred at higher pressures but these cages are not fully occupied at lower pressures. It was found that both small and medium cages are equally favored for occupancy by methane guests and at the same methane content, the system suffers a free energy penalty if only one type of cage is occupied. The simulations confirm the instability of the hydrate when the small and medium cages are empty. Hydrate decomposition was observed when less than 40% of the small and medium cages are occupied.

Within-farm spread of infectious salmon anemia virus (ISAV) in Atlantic salmon Salmo salar farms in Chile.

PubMed

Mardones, F O; Jansen, P A; Valdes-Donoso, P; Jarpa, M; Lyngstad, T M; Jimenez, D; Carpenter, T E; Perez, A M

2013-09-24

Spread of infectious salmon anemia virus (ISAV) at the cage level was quantified using a subset of data from 23 Atlantic salmon Salmo salar farms located in southern Chile. Data collected from official surveillance activities were systematically organized to obtain detailed information on infectious salmon anemia (ISA) outbreaks. Descriptive statistics for outbreak duration, proportion of infected fish, and time to secondary infection were calculated to quantify the magnitude of ISAV incursions. Linear and multiple failure time (MFT) regression models were used to determine factors associated with the cage-level reproduction number (Rc) and hazard rate (HR) for recurrent events, respectively. In addition, the Knox test was used to assess if cage-to-cage transmissions were clustered in space and time. Findings suggest that within farms, ISA outbreaks, on average, lasted 30 wk (median = 26 wk, 95% CI = 24 to 37 wk) and affected 57.3% (95% CI = 47.7 to 67.0%) of susceptible cages. The median time to secondarily diagnosed cages was 23 d. Occurrence of clinical ISAV outbreaks was significantly associated with increased Rc, whereas increased HR was significantly associated with clinical outbreaks and with a large number of fish. Spatio-temporal analysis failed to identify clustering of cage cases, suggesting that within-farm ISAV spread is independent of the spatial location of the cages. Results presented here will help to better understand ISAV transmission, to improve the design of surveillance programs in Chile and other regions in which salmon are intensively farmed, and to examine the economic impact of ISAV and related management strategies on various cost and demand shifting factors.

Horizontal transmission of Salmonella Enteritidis in experimentally infected laying hens housed in conventional or enriched cages.

PubMed

Gast, Richard K; Guraya, Rupa; Jones, Deana R; Anderson, Kenneth E

2014-12-01

The majority of human illnesses caused by Salmonella Enteritidis are attributed to contaminated eggs, and the prevalence of this pathogen in commercial laying flocks has been identified as a leading epidemiologic risk factor. Flock housing and management systems can affect opportunities for the introduction, transmission, and persistence of foodborne pathogens in poultry. The animal welfare implications of different types of housing for laying hens have been widely discussed in recent years, but the food safety consequences of these production systems remain incompletely understood. The present study assessed the effects of 2 different housing systems (conventional cages and colony cages enriched with perching and nesting areas) on the horizontal transmission of experimentally introduced Salmonella Enteritidis infection within groups of laying hens. In each of 2 trials, 136 hens were distributed among cages of both housing systems and approximately one-third of the hens in each cage were orally inoculated with doses of 10(8) cfu of Salmonella Enteritidis (phage type 13a in one trial and phage type 4 in the other). At regular intervals through 23 d postinoculation, cloacal swabs were collected from all hens (inoculated and uninoculated) and cultured for Salmonella Enteritidis. Horizontal contact transmission of infection was observed for both Salmonella Enteritidis strains, reaching peak prevalence values of 27.1% of uninoculated hens in conventional cages and 22.7% in enriched cages. However, no significant differences (P > 0.05) in the overall frequencies of horizontal Salmonella Enteritidis transmission were evident between the 2 types of housing. These results suggest that opportunities for Salmonella Enteritidis infection to spread horizontally throughout laying flocks may be similar in conventional and enriched cage-based production systems. ©2014 Poultry Science Association Inc.

Field Cage Studies and Progressive Evaluation of Genetically-Engineered Mosquitoes

PubMed Central

Facchinelli, Luca; Valerio, Laura; Ramsey, Janine M.; Gould, Fred; Walsh, Rachael K.; Bond, Guillermo; Robert, Michael A.; Lloyd, Alun L.; James, Anthony A.; Alphey, Luke; Scott, Thomas W.

2013-01-01

Background A genetically-engineered strain of the dengue mosquito vector Aedes aegypti, designated OX3604C, was evaluated in large outdoor cage trials for its potential to improve dengue prevention efforts by inducing population suppression. OX3604C is engineered with a repressible genetic construct that causes a female-specific flightless phenotype. Wild-type females that mate with homozygous OX3604C males will not produce reproductive female offspring. Weekly introductions of OX3604C males eliminated all three targeted Ae. aegypti populations after 10–20 weeks in a previous laboratory cage experiment. As part of the phased, progressive evaluation of this technology, we carried out an assessment in large outdoor field enclosures in dengue endemic southern Mexico. Methodology/Principal Findings OX3604C males were introduced weekly into field cages containing stable target populations, initially at 10∶1 ratios. Statistically significant target population decreases were detected in 4 of 5 treatment cages after 17 weeks, but none of the treatment populations were eliminated. Mating competitiveness experiments, carried out to explore the discrepancy between lab and field cage results revealed a maximum mating disadvantage of up 59.1% for OX3604C males, which accounted for a significant part of the 97% fitness cost predicted by a mathematical model to be necessary to produce the field cage results. Conclusions/Significance Our results indicate that OX3604C may not be effective in large-scale releases. A strain with the same transgene that is not encumbered by a large mating disadvantage, however, could have improved prospects for dengue prevention. Insights from large outdoor cage experiments may provide an important part of the progressive, stepwise evaluation of genetically-engineered mosquitoes. PMID:23350003