Gravity Effects in Small-Scale Structural Modeling

DTIC Science & Technology

1988-12-01

attenuating material (Reference 23). The materials tested were cellular concrete with fly ash, expanded polystyrene concrete with fly ash, foamed...polyurethane, foamed sulfer and molded expanded polystyrene . The studies showed that with proper adjustments in the cement content, water-cement ratio and foam...Compression (Ou,c) 4000 100 Tension (Ou,t) 400 10 E/Quc 1000 1000 Ou,c/Ou,t 10 10 Further analysis of the properties of expanded polystyrene concrete with

Relative merits of polystyrene foam and paper in hot drink cups: Implications for packaging

NASA Astrophysics Data System (ADS)

Hocking, Martin B.

1991-11-01

An analysis of the overall relative merits of the use of uncoated paper vs molded polystyrene bead foam in single-use 8-oz cups is described here as a manageable example of the use of paper vs plastics in packaging. In raw material requirements the paper cup required about 2.5 times its finished weight of raw wood and about the same hydrocarbon fueling requirement as is needed for the polystyrene foam cup. To process the raw materials about six times as much steam, 13 times as much electric power, and twice as much cooling water are consumed to produce the paper cup as compared to the polystyrene foam cup. Emission rates to air are similar and to water are generally higher for the paper cup. Virtually all primary use factors favor polystyrene foam over paper. Once used both cup types may be recycled. Landfill disposal of the two items under dry conditions will occupy similar landfill volumes after compaction and will confer similarly slow to nonexistent decomposition to either option. Under wet conditions polystyrene foam will not readily degrade, but may help other materials to do so. Paper under wet conditions will biodegrade to produce methane, a significant greenhouse gas, biochemical oxygen demand to any leachate, and instability to the land surface during the process. Both materials can be incinerated cleanly in a municipal waste stream with the option of energy recovery, to yield an ash volume of 2% 5% of the incoming waste volume. Overall this analysis would suggest that polystyrene foam, with an extension to plastics in general, should be given more evenhanded consideration relative to paper in packaging applications than is currently the case.

Polystyrene Foam Products Equation of State as a Function of Porosity and Fill Gas

NASA Astrophysics Data System (ADS)

Mulford, R. N.; Swift, D. C.

2009-12-01

An accurate EOS for polystyrene foam is necessary for analysis of numerous experiments in shock compression, inertial confinement fusion, and astrophysics. Plastic to gas ratios vary between various samples of foam, according to the density and cell-size of the foam. A matrix of compositions has been investigated, allowing prediction of foam response as a function of the plastic-to-air ratio. The EOS code CHEETAH allows participation of the air in the decomposition reaction of the foam. Differences between air-filled, Ar-blown, and CO2-blown foams are investigated, to estimate the importance of allowing air to react with products of polystyrene decomposition. O2-blown foams are included in some comparisons, to amplify any consequences of reaction with oxygen in air. He-blown foams are included in some comparisons, to provide an extremum of density. Product pressures are slightly higher for oxygen-containing fill gases than for non-oxygen-containing fill gases. Examination of product species indicates that CO2 decomposes at high temperatures.

Quantitative Determination of Wax Contamination in Polystyrene HIPE Foam Using Solid-State NMR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cluff, Kyle James; Goodwin, Lynne Alese; Hamilton, Christopher Eric

Differences in molecular mobility between polystyrene foam and Brij-78 wax results in vast differences in the 1H nuclear magnetic resonance (NMR) linewidth. This allows for the convenient determination of wax content in the polystyrene foam components of inertial confinement fusion targets via solid-state NMR. Lastly, contamination levels as low as 0.1% are easily recognized and quantified, and the detection limit is calculated to be 0.02% even when only 32 transients are recorded.

Quantitative Determination of Wax Contamination in Polystyrene HIPE Foam Using Solid-State NMR

DOE PAGES

Cluff, Kyle James; Goodwin, Lynne Alese; Hamilton, Christopher Eric; ...

2017-11-29

Differences in molecular mobility between polystyrene foam and Brij-78 wax results in vast differences in the 1H nuclear magnetic resonance (NMR) linewidth. This allows for the convenient determination of wax content in the polystyrene foam components of inertial confinement fusion targets via solid-state NMR. Lastly, contamination levels as low as 0.1% are easily recognized and quantified, and the detection limit is calculated to be 0.02% even when only 32 transients are recorded.

The role of EPS concentration in MBR foaming: analysis of a submerged pilot plant.

PubMed

Di Bella, Gaetano; Torregrossa, Michele; Viviani, Gaspare

2011-01-01

Foaming in Membrane BioReactor (MBR) is a frequently discussed topic. Some authors reported that the phenomenon is due to filamentous organisms, like at Conventional Activated Sludge (CAS) plants. However, in recent years, other authors reported that the Extra-cellular Polymer Substances (EPSs) concentration is an important factor for controlling foam as well. Nevertheless, even if a number of MBR plants are affected by foaming, presently there are no suitable methods to evaluate the phenomenon. To facilitate the study of this controversial phenomenon in an MBR system, certain foam tests proposed in the past for CASPs were investigated. The results of the tests were able to adequately measure quantity, stability and quality of the foam. In particular, the Scum Index increased proportionally with the EPS concentration and mixed liquor viscosity; Foam Power was mainly correlated with the protein concentration of in the EPS; Foam Rating was also correlated with the EPS concentration. Copyright © 2010 Elsevier Ltd. All rights reserved.

Polystyrene foam products equation of state as a function of porosity and fill gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mulford, Roberta N; Swift, Damian C

2009-01-01

An accurate EOS for polystyrene foam is necessary for analysis of numerous experiments in shock compression, inertial confinement fusion, and astrophysics. Plastic to gas ratios vary between various samples of foam, according to the density and cell-size of the foam. A matrix of compositions has been investigated, allowing prediction of foam response as a function of the plastic-to-air ratio. The EOS code CHEETAH allows participation of the air in the decomposition reaction of the foam. Differences between air-filled, Ar-blown, and CO{sub 2}-blown foams are investigated, to estimate the importance of allowing air to react with products of polystyrene decomposition. O{submore » 2}-blown foams are included in some comparisons, to amplify any consequences of reaction with oxygen in air. He-blown foams are included in some comparisons, to provide an extremum of density. Product pressures are slightly higher for oxygen-containing fill gases than for non-oxygen-containing fill gases. Examination of product species indicates that CO{sub 2} decomposes at high temperatures.« less

Simulation of Prestressed Concrete Sandwich Panels Subjected to Blast Loads (Preprint)

DTIC Science & Technology

2010-02-01

configuration. Conventionally reinforced panels had configurations of 3-2-3 a nd 6-2-3. Insulating foams included expanded polystyrene , extruded expanded ...Properties of Extruded Expanded Polystyrene Foam Building Materials. M.S.C.E. report, University of Alabama at Birmingham. Livermore Software... polystyrene , and polyisocyanurate. Compressive testing of insulating f oams used as construction materials was used to define the stress/strain

Polystyrene Foam EOS as a Function of Porosity and Fill Gas

NASA Astrophysics Data System (ADS)

Mulford, Roberta; Swift, Damian

2009-06-01

An accurate EOS for polystyrene foam is necessary for analysis of numerous experiments in shock compression, inertial confinement fusion, and astrophysics. Plastic to gas ratios vary between various samples of foam, according to the density and cell-size of the foam. A matrix of compositions has been investigated, allowing prediction of foam response as a function of the plastic-to-air ratio. The EOS code CHEETAH allows participation of the air in the decomposition reaction of the foam, Differences between air-filled, nitrogen-blown, and CO2-blown foams are investigated, to estimate the importance of allowing air to react with plastic products during decomposition. Results differ somewhat from the conventional EOS, which are generated from values for plastic extrapolated to low densities.

The effectiveness of the biodegradation of raw and processed polystyrene by mealworms

NASA Astrophysics Data System (ADS)

Leluk, Karol; Hanus-Lorenz, Beata; Rybak, Justyna; Bożek, Magdalena

2017-11-01

In our studies biodegradation of four variants of polystyrene was performed. We tested: raw material (PS), processed polystyrene (PSr), building insulation material (EPS) and food packaging boxes (PSp). Materials were characterized by means melt flow ratio (MFR), shore hardness and gloss. The biochemical assessment of macromolecules (proteins, lipids and sugars) in the mealworms organisms fed with tested forms of polystyrene allowed us to set how efficient and beneficial the biodegradation of types of polystyrene is. We also evaluated the variability of bacterial community in larval guts by the use of denaturing gradient gel electrophoresis (DGGE) on the bacterial DNA of 16S rRNA genes amplified in polymerase chain reaction (PCR). The results suggest that EPS and PSp polystyrene are the most digestible for T. molitor larvae. The metabolic degradation of polystyrene is probably strictly connected with the changes in biodiversity of gut bacteria.

Electrical conductivity and electromagnetic interference shielding of epoxy nanocomposite foams containing functionalized multi-wall carbon nanotubes

NASA Astrophysics Data System (ADS)

Li, Jiantong; Zhang, Guangcheng; Zhang, Hongming; Fan, Xun; Zhou, Lisheng; Shang, Zhengyang; Shi, Xuetao

2018-01-01

Epoxy/functionalized multi-wall carbon nanotube (EP/F-MWCNT) microcellular foams were fabricated through a supercritical CO2 (scCO2) foaming method. MWCNTs with carboxylation treatment were disentangled by using alpha-zirconium phosphate (ZrP) assisting dispersion method and functionalized with sulfanilamide. The F-MWCNTs were redispersed in acetone for mixing with epoxy resins to prepare nanocomposites. It was found that the dispersion of MWCNTs could be improved, thus heterogeneous nucleation effect of F-MWCNTs took place effectively during the foaming process, resulting in the formation of microcellular structure with larger cell density and smaller cell size. The volume conductivity and electromagnetic interference shielding performance of foamed EP/F-MWCNT nanocomposites were studied. When the F-MWCNT addition was 5 wt%, the conductivity of the foamed EP/F-MWCNT nanocomposites was 3.02 × 10-4 S/cm and the EMI shielding effectiveness (SE) reached 20.5 dB, significantly higher than the corresponding results of nanocomposite counterparts, indicating that introducing microcellular structure in EP/F-MWCNT nanocomposites would beneficial to improve their electrical conductivity and electromagnetic interference shielding performance.

Standoff Acoustic Shear Wave Imaging Using LFM Chirps

DTIC Science & Technology

2011-03-21

is typically ignored due to the large wavelengths in biological tissue. For the test material presented in this paper ( expanded polystyrene foam...inhomogeneous sound speed, 1( )c x , for a 2.5×5×7 cm steel parallelepiped embedded in a 15×23×23 cm block of expanded polystyrene foam, which

Plastic Materials for Insulating Applications.

ERIC Educational Resources Information Center

Wang, S. F.; Grossman, S. J.

1987-01-01

Discusses the production and use of polymer materials as thermal insulators. Lists several materials that provide varying degrees of insulation. Describes the production of polymer foam and focuses on the major applications of polystyrene foam, polyurethane foam, and polyisocyanurate foam. (TW)

Structural Composite Construction Materials Manufactured from Municipal Solid Waste

DTIC Science & Technology

1994-04-20

in Table 1. Candidate matrix materials included polystyrene (PS) or expanded polystyrene (EPS), high density polyethylene (HDPE), and polyethylene...companies make a variety of expanded polystyrene insulation panels that arc used in insulation and roofing systems.46 Thermoplastics are seeing

Evaluation of select blends of cotton byproducts in the manufacture of biodegradable packaging material

USDA-ARS?s Scientific Manuscript database

Polystyrene is one of the most widely used plastics in the manufacture of packaging materials. Extruded polystyrene foam is commonly sold under the trademark name of StyrofoamTM. Polystyrene packaging is a multibillion dollar a year industry. Since polystyrene is non-biodegradable, a biodegradable m...

Portable X-ray fluorescence for the detection of POP-BFRs in waste plastics.

PubMed

Sharkey, Martin; Abdallah, Mohamed Abou-Elwafa; Drage, Daniel S; Harrad, Stuart; Berresheim, Harald

2018-05-17

The purpose of this study was to establish the efficacy of portable X-ray fluorescence (XRF) instrumentation as a screening tool for a variety of end of life plastics which may contain excess amounts of brominated flame retardants (BFRs), in compliance with European Union (EU) and United Nations Environment Programme (UNEP) legislative limits (low POP concentration limits - LPCLs). 555 samples of waste plastics were collected from eight waste and recycling sites in Ireland, including waste electrical and electronic equipment (WEEE), textiles, polyurethane foams (PUFs), and expanded polystyrene foams. Samples were screened for bromine content, in situ using a Niton™ XL3T GOLDD XRF analyser, the results of which were statistically compared to mass spectrometry (MS)-based measurements of polybrominated diphenyl ethers (PBDEs), hexabromocyclododecane (HBCDD) and tetrabromobisphenol-A (TBBP-A) concentrations in the same samples. Regression between XRF and MS for WEEE samples shows that, despite an overall favourable trend, large deviations occur for a cluster of samples indicative of other bromine-based compounds in some samples; even compensating for false-positives due to background interference from electronic components, XRF tends to over-estimate MS-determined BFR concentrations in the 100 to 10,000 mg kg -1 range. Substantial deviations were additionally found between results for PUFs, textiles and polystyrene samples, with the XRF over-estimating BFR concentrations by a factor of up to 1.9; this is likely due to matrix effects influencing XRF measurements. However, expanded (EPS) and extruded polystyrene (XPS) yielded much more reliable estimations of BFR-content due to a dominance of HBCDD in these materials. XRF proved much more reliable as a "pass/fail" screening tool for LPCL compliance (including a prospective LPCL on Deca-BDE based on REACH). Using a conservative threshold of BFR content exceeding legislative limits (710 mg kg -1 bromine attributed to Penta-BDE), XRF mistakenly identifies only 6 % of samples (34/555) as exceeding legislative limits. Copyright © 2018 Elsevier B.V. All rights reserved.

Exopolysaccharide-Independent Social Motility of Myxococcus xanthus

PubMed Central

Hu, Wei; Hossain, Muhaiminu; Lux, Renate; Wang, Jing; Yang, Zhe; Li, Yuezhong; Shi, Wenyuan

2011-01-01

Social motility (S motility), the coordinated movement of large cell groups on agar surfaces, of Myxococcus xanthus requires type IV pili (TFP) and exopolysaccharides (EPS). Previous models proposed that this behavior, which only occurred within cell groups, requires cycles of TFP extension and retraction triggered by the close interaction of TFP with EPS. However, the curious observation that M. xanthus can perform TFP-dependent motility at a single-cell level when placed onto polystyrene surfaces in a highly viscous medium containing 1% methylcellulose indicated that “S motility” is not limited to group movements. In an apparent further challenge of the previous findings for S motility, mutants defective in EPS production were found to perform TFP-dependent motility on polystyrene surface in methylcellulose-containing medium. By exploring the interactions between pilin and surface materials, we found that the binding of TFP onto polystyrene surfaces eliminated the requirement for EPS in EPS- cells and thus enabled TFP-dependent motility on a single cell level. However, the presence of a general anchoring surface in a viscous environment could not substitute for the role of cell surface EPS in group movement. Furthermore, EPS was found to serve as a self-produced anchoring substrate that can be shed onto surfaces to enable cells to conduct TFP-dependent motility regardless of surface properties. These results suggested that in certain environments, such as in methylcellulose solution, the cells could bypass the need for EPS to anchor their TPF and conduct single-cell S motility to promote exploratory movement of colonies over new specific surfaces. PMID:21245931

Ignition of expandable polystyrene foam by a hot particle: an experimental and numerical study.

PubMed

Wang, Supan; Chen, Haixiang; Liu, Naian

2015-01-01

Many serious fires have occurred in recent years due to the ignition of external building insulation materials by hot metallic particles. This work studied the ignition of expandable polystyrene foam by hot metallic particles experimentally and numerically. In each experiment, a spherical steel particle was heated to a high temperature (within 1173-1373K) and then dropped to the surface of an expandable polystyrene foam block. The particles used in experiments ranged from 3mm to 7 mm in radius. The observed results for ignition were categorized into two types: "flaming ignition" and "no ignition", and the flaming ignition limit was determined by statistical analysis. According to the experimental observations, a numerical model was proposed, taking into account the reactant consumption and volatiles convection of expandable polystyrene decomposition in air. Three regimes, no ignition, unstable ignition and stable ignition, were identified, and two critical particle temperatures for separating the three regimes were determined. Comparison with the experimental data shows that the model can predict the range of critical ignition temperatures reasonably well. Copyright © 2014 Elsevier B.V. All rights reserved.

Optimizing biomass blends for manufacturing molded packaging materials using mycelium

USDA-ARS?s Scientific Manuscript database

Polystyrene is one of the most widely used plastics and is commonly produced in three forms: 1) Extruded polystyrene – disposable utensils, CD/DVD cases, yogurt containers, smoke alarm housing, etc.; 2) Expanded polystyrene foam – molded packaging materials and packaging "peanuts"; 3) Extruded polys...

Engineering Assessment of Big House at Summit Station, Greenland

DTIC Science & Technology

2011-04-01

Open cell expanded polystyrene insulation c EPS is not thought to be under the T-111 siding (communication 04 Nov 2010) d Quad-pane window ERDC...eastern side of the building where, in 2008, the roof access hatch was relocated. In 1999, the exterior was re-sheathed with 38- mm expanded ... polystyrene (EPS) insulation and 12.7-mm T-111 siding, which was attached with a number of fasteners. The wall thickness is 178 mm (Fig. 3). In 2006, a

Fire performances of foam core particleboards continuously produced in a one-step process

Treesearch

Ali Shalbafan; Mark A. Dietenberger; Johannes Welling

2013-01-01

For further progress of novel foam core particleboards, their fire performance was examined with cone calorimetry tests (ASTM E 1354-11a). Specimens with varying surface layer thicknesses, foam densities (polystyrene foam), and processing temperatures were tested. Using the initially recommended cone irradiance of 35 kW/m2, different flammability...

Evaluation of Biomass Residual Substrate Blends for Eco-Friendly Packaging and Insulation Sheets/Panels

USDA-ARS?s Scientific Manuscript database

Polystyrene is one of the most widely used plastics and is commonly produced in three forms: 1) Extruded polystyrene – disposable utensils, CD/DVD cases, yogurt containers, smoke alarm housing, etc.; 2) Expanded polystyrene foam – molded packaging materials and packaging "peanuts"; and 3) Extruded p...

Optimization of biomass blends in the manufacture of molded packaging materials produced using fungal mycelium

USDA-ARS?s Scientific Manuscript database

Polystyrene is one of the most widely used plastics and is commonly produced in three forms: 1) Extruded polystyrene – disposable utensils, CD/DVD cases, yogurt containers, smoke alarm housing, etc.; 2) Expanded polystyrene foam – molded packaging materials and packaging "peanuts"; 3) Extruded polys...

46 CFR 160.010-1 - Incorporation by reference.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Specification, Plastic Material, Cellular Polyurethane, Foam-In-Place, Rigid (2 and 4 Pounds per Cubic Foot....mil/quicksearch/. (1) MIL-P-19644C, Military Specification, Plastic Molding Material (Polystyrene Foam...

46 CFR 160.010-1 - Incorporation by reference.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Specification, Plastic Material, Cellular Polyurethane, Foam-In-Place, Rigid (2 and 4 Pounds per Cubic Foot....mil/quicksearch/. (1) MIL-P-19644C, Military Specification, Plastic Molding Material (Polystyrene Foam...

Formation of microplastics by polychaetes (Marphysa sanguinea) inhabiting expanded polystyrene marine debris.

PubMed

Jang, Mi; Shim, Won Joon; Han, Gi Myung; Song, Young Kyoung; Hong, Sang Hee

2018-06-01

Fragmentation of large plastic debris into smaller particles results in increasing microplastic concentrations in the marine environment. In plastic debris fragmentation processes, the influence of biological factors remains largely unknown. This study investigated the fragmentation of expanded polystyrene (EPS) debris by polychaetes (Marphysa sanguinea) living on the debris. A large number of EPS particles (131 ± 131 particles/individual, 0.2-3.8 mm in length) were found in the digestive tracts of burrowing polychaetes living on EPS debris. To confirm the formation of microplastics by polychaetes and identify the quantity and morphology of produced microplastics, polychaetes were exposed to EPS blocks in filtered seawater under laboratory conditions. Polychaetes burrowed into the blocks and created numerous EPS microplastic particles, indicating that a single polychaete can produce hundreds of thousands of microplastic particles per year. These results reveal the potential role of marine organisms as microplastic producers in the marine environment. Copyright © 2018 Elsevier Ltd. All rights reserved.

Determination of hexabromocyclododecane by flowing atmospheric pressure afterglow mass spectrometry.

PubMed

Smoluch, Marek; Silberring, Jerzy; Reszke, Edward; Kuc, Joanna; Grochowalski, Adam

2014-10-01

The first application of a flowing atmospheric-pressure afterglow ion source for mass spectrometry (FAPA-MS) for the chemical characterization and determination of hexabromocyclododecane (HBCD) is presented. The samples of technical HBCD and expanded polystyrene foam (EPS) containing HBCD as a flame retardant were prepared by dissolving the appropriate solids in dichloromethane. The ionization of HBCD was achieved with a prototype FAPA source. The ions were detected in the negative-ion mode. The ions corresponding to a deprotonated HBCD species (m/z 640.7) as well as chlorine (m/z 676.8), nitrite (m/z 687.8) and nitric (m/z 703.8) adducts were observed in the spectra. The observed isotope pattern is characteristic for a compound containing six bromine atoms. This technique is an effective approach to detect HBCD, which is efficiently ionized in a liquid phase, resulting in high detection efficiency and sensitivity. Copyright © 2014 Elsevier B.V. All rights reserved.

SPH-4 U.S. Army Flight Helmet Performance 1972-1983

DTIC Science & Technology

1984-11-01

epoxy resin and fiberglass cloth. 2. Liner -Energy-absorbing 1.3 cm thick expanded polystyrene with a density of 0.08 gm/cm 3 3. Suspension - With...thick epoxy or polyester resin and fiberglass cloth layup provided in small, medium, and large siaeso b. Liner- Energy-absorbing 1.3 cm thick expanded ... polystyrene -foam with density of .08 gm/cu3. c ’ pension- Provided by three leather-covered foam pads located at the front, crown, and rear of the

Phenolic cutter for machining foam insulation

NASA Technical Reports Server (NTRS)

Blair, T. A.; Miller, A. C.; Price, B. W.; Stiles, W. S.

1970-01-01

Pre-pregged fiber glass is an efficient abrasive for machining polystyrene and polyurethane foams. It bonds easily to any cutter base made of aluminum, steel, or phenolic, is inexpensive, and is readily available.

Parameters estimation of sandwich beam model with rigid polyurethane foam core

NASA Astrophysics Data System (ADS)

Barbieri, Nilson; Barbieri, Renato; Winikes, Luiz Carlos

2010-02-01

In this work, the physical parameters of sandwich beams made with the association of hot-rolled steel, Polyurethane rigid foam and High Impact Polystyrene, used for the assembly of household refrigerators and food freezers are estimated using measured and numeric frequency response functions (FRFs). The mathematical models are obtained using the finite element method (FEM) and the Timoshenko beam theory. The physical parameters are estimated using the amplitude correlation coefficient and genetic algorithm (GA). The experimental data are obtained using the impact hammer and four accelerometers displaced along the sample (cantilevered beam). The parameters estimated are Young's modulus and the loss factor of the Polyurethane rigid foam and the High Impact Polystyrene.

Novel nanoporous sorbent for solid-phase extraction in petroleum fingerprinting

NASA Astrophysics Data System (ADS)

Alayande, S. Oluwagbemiga; Hlengilizwe, Nyoni; Dare, E. Olugbenga; Msagati, Titus A. M.; Akinlabi, A. Kehinde; Aiyedun, P. O.

2016-04-01

Sample preparation is crucial in the analysis of petroleum and its derivatives. In this study, developing affordable sorbent for petroleum fingerprinting analysis using polymer waste such expanded polystyrene was explored. The potential of electrospun expanded polystyrene (EPS) as a sorbent for the solid-phase extraction (SPE) technique was investigated, and its efficiency was compared with commercial cartridges such as alumina, silica and alumina/silica hybrid commercial for petroleum fingerprinting analysis. The chromatograms showed that the packed electrospun EPS fibre demonstrated excellent properties for SPE applications relative to the hybrid cartridges.

Thermally insulating and fire-retardant lightweight anisotropic foams based on nanocellulose and graphene oxide.

PubMed

Wicklein, Bernd; Kocjan, Andraž; Salazar-Alvarez, German; Carosio, Federico; Camino, Giovanni; Antonietti, Markus; Bergström, Lennart

2015-03-01

High-performance thermally insulating materials from renewable resources are needed to improve the energy efficiency of buildings. Traditional fossil-fuel-derived insulation materials such as expanded polystyrene and polyurethane have thermal conductivities that are too high for retrofitting or for building new, surface-efficient passive houses. Tailored materials such as aerogels and vacuum insulating panels are fragile and susceptible to perforation. Here, we show that freeze-casting suspensions of cellulose nanofibres, graphene oxide and sepiolite nanorods produces super-insulating, fire-retardant and strong anisotropic foams that perform better than traditional polymer-based insulating materials. The foams are ultralight, show excellent combustion resistance and exhibit a thermal conductivity of 15 mW m(-1) K(-1), which is about half that of expanded polystyrene. At 30 °C and 85% relative humidity, the foams retained more than half of their initial strength. Our results show that nanoscale engineering is a promising strategy for producing foams with excellent properties using cellulose and other renewable nanosized fibrous materials.

Widespread detection of a brominated flame retardant, hexabromocyclododecane, in expanded polystyrene marine debris and microplastics from South Korea and the Asia-Pacific coastal region.

PubMed

Jang, Mi; Shim, Won Joon; Han, Gi Myung; Rani, Manviri; Song, Young Kyoung; Hong, Sang Hee

2017-12-01

The role of marine plastic debris and microplastics as a carrier of hazardous chemicals in the marine environment is an emerging issue. This study investigated expanded polystyrene (EPS, commonly known as styrofoam) debris, which is a common marine debris item worldwide, and its additive chemical, hexabromocyclododecane (HBCD). To obtain a better understanding of chemical dispersion via EPS pollution in the marine environment, intensive monitoring of HBCD levels in EPS debris and microplastics was conducted in South Korea, where EPS is the predominant marine debris originate mainly from fishing and aquaculture buoys. At the same time, EPS debris were collected from 12 other countries in the Asia-Pacific region, and HBCD concentrations were measured. HBCD was detected extensively in EPS buoy debris and EPS microplastics stranded along the Korean coasts, which might be related to the detection of a quantity of HBCD in non-flame-retardant EPS bead (raw material). The wide detection of the flame retardant in sea-floating buoys, and the recycling of high-HBCD-containing EPS waste inside large buoys highlight the need for proper guidelines for the production and use of EPS raw materials, and the recycling of EPS waste. HBCD was also abundantly detected in EPS debris collected from the Asia-Pacific coastal region, indicating that HBCD contamination via EPS debris is a common environmental issue worldwide. Suspected tsunami debris from Alaskan beaches indicated that EPS debris has the potential for long-range transport in the ocean, accompanying the movement of hazardous chemicals. The results of this study indicate that EPS debris can be a source of HBCD in marine environments and marine food web. Copyright © 2017 Elsevier Ltd. All rights reserved.

21 CFR 178.3010 - Adjuvant substances used in the manufacture of foamed plastics.

Code of Federal Regulations, 2011 CFR

2011-04-01

... prescribed limitations: List of substances Limitations Azodicarbonamide For use as a blowing agent in pol... agent in polystyrene. Isopentane For use as a blowing agent in polystyrene. n-Pentane Do. 1,1,2,2-Tetra-chloroethylene For use only as a blowing agent adjuvant in polystyrene at a level not to exceed 0.3 percent by...

21 CFR 178.3010 - Adjuvant substances used in the manufacture of foamed plastics.

Code of Federal Regulations, 2012 CFR

2012-04-01

... prescribed limitations: List of substances Limitations Azodicarbonamide For use as a blowing agent in pol... agent in polystyrene. Isopentane For use as a blowing agent in polystyrene. n-Pentane Do. 1,1,2,2-Tetra-chloroethylene For use only as a blowing agent adjuvant in polystyrene at a level not to exceed 0.3 percent by...

21 CFR 178.3010 - Adjuvant substances used in the manufacture of foamed plastics.

Code of Federal Regulations, 2013 CFR

2013-04-01

... prescribed limitations: List of substances Limitations Azodicarbonamide For use as a blowing agent in pol... agent in polystyrene. Isopentane For use as a blowing agent in polystyrene. n-Pentane Do. 1,1,2,2-Tetra-chloroethylene For use only as a blowing agent adjuvant in polystyrene at a level not to exceed 0.3 percent by...

46 CFR 160.010-1 - Incorporation by reference.

Code of Federal Regulations, 2012 CFR

2012-10-01

... (Polystyrene Foam, Expanded Bead), (July 10, 1970), IBR approved for § 160.010-5 (“MIL-P-19644C”). (2) MIL-P-21929B, Military Specification, Plastic Material, Cellular Polyurethane, Foam-In-Place, Rigid (2 and 4...

Development of a Water Soluble Foam Packaging Material

DTIC Science & Technology

1975-01-01

Material, Expanded Polystyrene , Looae-Fill Bulk and standard properties were established. Additional investigations conducted on the loose-fill samples...mechanical properties when tested as described in Federal Specification PPP-O-1683; Cushioning Material, Expanded Polystyrene , Loose-Fill Bulk. The following

In-situ Heat Flux Measurements in Buildings: Applications and Interpretations of Results, Proceedings of a Workshop Held in Hanover, New Hampshire on 22-23 May 1990

DTIC Science & Technology

1991-02-01

expanded polystyrene , i.e., R-value about 0.3 m 2 °C/W. The surface resistance remains at 0.09 m2 °C/W. From Table 1 we see that the power-law error Ep...8217 4 10 mm " ! L /1016 mm 102-mm-Thick Expanded Polystyrene Board Figure 1. Illustration of the calibration of HFTs in the NIST 1-m Guarded Hot...Description of Wall Specimens. Polystyrene Wall 100-mm expanded polystyrene insulation Composite Masonry Wall 100-mm expanded polystyrene insulation

A Polymer "Pollution Solution" Classroom Activity.

ERIC Educational Resources Information Center

Helser, Terry L.

1996-01-01

Explains an approach to presenting polymer chemistry to nonmajors that employs polystyrene foam, foam peanuts made from water soluble starch, and water soluble plastic bags. Students are presented with a pollution scenario and are guided to the discovery of solutions. (DDR)

40 CFR Appendix M to Subpart G - Unacceptable Substitutes Listed in the September 30, 2004 Final Rule, Effective November 29, 2004

Code of Federal Regulations, 2010 CFR

2010-07-01

... —Rigid polyurethane slabstock and other foams —Polystyrene extruded insulation boardstock and billet...—Unacceptable Substitutes Listed in the September 30, 2004 Final Rule, Effective November 29, 2004 Foam Blowing—Unacceptable Substitutes End-use Substitute Decision Comments All foam end-uses: HCFC-141b Unacceptable...

40 CFR Appendix M to Subpart G of... - Unacceptable Substitutes Listed in the September 30, 2004 Final Rule, Effective November 29, 2004

Code of Federal Regulations, 2014 CFR

2014-07-01

... refrigeration, and sandwich panels —Rigid polyurethane slabstock and other foams —Polystyrene extruded... 29, 2004 Foam Blowing—Unacceptable Substitutes End-use Substitute Decision Comments All foam end-uses: HCFC-141b Unacceptable Alternatives exist with lower or zero = ODP. —Rigid polyurethane and...

40 CFR Appendix M to Subpart G - Unacceptable Substitutes Listed in the September 30, 2004 Final Rule, Effective November 29, 2004

Code of Federal Regulations, 2012 CFR

2012-07-01

... —Rigid polyurethane slabstock and other foams —Polystyrene extruded insulation boardstock and billet...—Unacceptable Substitutes Listed in the September 30, 2004 Final Rule, Effective November 29, 2004 Foam Blowing—Unacceptable Substitutes End-use Substitute Decision Comments All foam end-uses: HCFC-141b Unacceptable...

40 CFR Appendix M to Subpart G - Unacceptable Substitutes Listed in the September 30, 2004 Final Rule, Effective November 29, 2004

Code of Federal Regulations, 2011 CFR

2011-07-01

... —Rigid polyurethane slabstock and other foams —Polystyrene extruded insulation boardstock and billet...—Unacceptable Substitutes Listed in the September 30, 2004 Final Rule, Effective November 29, 2004 Foam Blowing—Unacceptable Substitutes End-use Substitute Decision Comments All foam end-uses: HCFC-141b Unacceptable...

40 CFR Appendix M to Subpart G of... - Unacceptable Substitutes Listed in the September 30, 2004 Final Rule, Effective November 29, 2004

Code of Federal Regulations, 2013 CFR

2013-07-01

... refrigeration, and sandwich panels —Rigid polyurethane slabstock and other foams —Polystyrene extruded... 29, 2004 Foam Blowing—Unacceptable Substitutes End-use Substitute Decision Comments All foam end-uses: HCFC-141b Unacceptable Alternatives exist with lower or zero = ODP. —Rigid polyurethane and...

Releasing of hexabromocyclododecanes from expanded polystyrenes in seawater -field and laboratory experiments.

PubMed

Rani, Manviri; Shim, Won Joon; Jang, Mi; Han, Gi Myung; Hong, Sang Hee

2017-10-01

Expanded polystyrene (EPS) is a major component of marine debris globally. Recently, hazardous hexabromocyclododecanes (HBCDDs) were detected in EPS buoys used for aquaculture farming. Subsequently, enrichment of HBCDDs was found in nearby marine sediments and mussels growing on EPS buoys. It was suspected that EPS buoys and their debris might be sources of HBCDDs. To confirm this, the release of HBCDDs from EPS spherules detached from a buoy to seawater was investigated under field (open sea surface and closed outdoor chambers with sun exposure and in the dark) and laboratory (particle-size) conditions. In all exposure groups, initial rapid leaching of HBCDDs was followed by slow desorption over time. Abundant release of HBCDDs was observed from EPS spherules exposed to the open sea surface (natural) and on exposure to sunlight irradiation or in the dark in controlled saline water. Water leaching and UV-light/temperature along with possibly biodegradation were responsible for about 37% and 12% of HBCDDs flux, respectively. Crumbled EPS particles (≤1 mm) in samples deployed on the sea surface for 6 months showed a high degree of weathering. This implies that surface erosion and further fragmentation of EPS via environmental weathering could enhance the leaching of HBCDDs from the surface of EPS. Overall, in the marine environment, HBCDDs could be released to a great extent from EPS products and their debris due to the cumulative effects of the movement of large volumes of water (dilution), biodegradation, UV-light/temperature, wave action (shaking), salinity and further fragmentation of EPS spherules. Copyright © 2017 Elsevier Ltd. All rights reserved.

Design and evaluation of expanded polystyrene geofoam embankments for the I-15 reconstruction project, Salt Lake City, Utah.

DOT National Transportation Integrated Search

2012-10-01

The report discusses the design and 10-year performance evaluations of Expanded Polystyrene (EPS) Geofoam embankment constructed for the I-15 Reconstruction Project in Salt Lake City, Utah between 1998 and 2002. It contains methods to evaluate the al...

Swarm intelligence application for optimization of CO2 diffusivity in polystyrene-b-polybutadiene-b-polystyrene (SEBS) foaming

NASA Astrophysics Data System (ADS)

Sharudin, Rahida Wati; Ajib, Norshawalina Muhamad; Yusoff, Marina; Ahmad, Mohd Aizad

2017-12-01

Thermoplastic elastomer SEBS foams were prepared by using carbon dioxide (CO2) as a blowing agent and the process is classified as physical foaming method. During the foaming process, the diffusivity of CO2 need to be controlled since it is one of the parameter that will affect the final cellular structure of the foam. Conventionally, the rate of CO2 diffusion was measured experimentally by using a highly sensitive device called magnetic suspension balance (MSB). Besides, this expensive MSB machine is not easily available and measurement of CO2 diffusivity is quite complicated as well as time consuming process. Thus, to overcome these limitations, a computational method was introduced. Particle Swarm Optimization (PSO) is a part of Swarm Intelligence system which acts as a beneficial optimization tool where it can solve most of nonlinear complications. PSO model was developed for predicting the optimum foaming temperature and CO2 diffusion rate in SEBS foam. Results obtained by PSO model are compared with experimental results for CO2 diffusivity at various foaming temperature. It is shown that predicted optimum foaming temperature at 154.6 °C was not represented the best temperature for foaming as the cellular structure of SEBS foamed at corresponding temperature consisted pores with unstable dimension and the structure was not visibly perceived due to foam shrinkage. The predictions were not agreed well with experimental result when single parameter of CO2 diffusivity is considered in PSO model because it is not the only factor that affected the controllability of foam shrinkage. The modification on the PSO model by considering CO2 solubility and rigidity of SEBS as additional parameters needs to be done for obtaining the optimum temperature for SEBS foaming. Hence stable SEBS foam could be prepared.

Extended Plate and Beam Wall System: Concept Investigation and Initial Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiehagen, J.; Kochkin, V.

A new and innovative High-R wall design, referred to as the Extended Plate & Beam (EP&B), is under development. The EP&B system uniquely integrates foam sheathing insulation with wall framing such that wood structural panels are installed exterior of the foam sheathing, enabling the use of standard practices for installation of drainage plane, windows and doors, claddings, cavity insulation, and the standard exterior foam sheathing installation approach prone to damage of the foam during transportation of prefabricated wall panels. As part of the ongoing work, the EP&B wall system concept has undergone structural verification testing and has been positively vettedmore » by a group of industry stakeholders. Having passed these initial milestone markers, the advanced wall system design has been analyzed to assess cost implications relative to other advanced wall systems, undergone design assessment to develop construction details, and has been evaluated to develop representative prescriptive requirements for the building code. This report summarizes the assessment steps conducted to-date and provides details of the concept development.« less

Extended Plate and Beam Wall System: Concept Investigation and Initial Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiehagen, J.; Kochkin, V.

2015-08-01

A new and innovative High-R wall design, referred to as the Extended Plate & Beam (EP&B), is under development. The EP&B system uniquely integrates foam sheathing insulation with wall framing such that wood structural panels are installed exterior of the foam sheathing, enabling the use of standard practices for installation of drainage plane, windows and doors, claddings, cavity insulation, and the standard exterior foam sheathing installation approach prone to damage of the foam during transportation of prefabricated wall panels. As part of the ongoing work, the EP&B wall system concept has undergone structural verification testing and has been positively vettedmore » by a group of industry stakeholders. Having passed these initial milestone markers, the advanced wall system design has been analyzed to assess cost implications relative to other advanced wall systems, undergone design assessment to develop construction details, and has been evaluated to develop representative prescriptive requirements for the building code. This report summarizes the assessment steps conducted to-date and provides details of the concept development.« less

VIBRATION TESTING OF RESILIENT PACKAGE CUSHIONING MATERIALS

DTIC Science & Technology

government and industry. Testing equipment which meets tentative ASTM requirements was developed. Preliminary tests were conducted on a resilient expanded ... polystyrene foam (in 3 densities) and a polyether urethane foam (in one density). When vibrated under static loads known to provide optimum shock

46 CFR 160.035-1 - Applicable specifications.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Laminates, Fibrous Glass Reinforced, Marine Structural. MIL-P-19644—Plastic Foam, Molded Polystyrene..., Polyester, Low Pressure Laminating, Fire Retardant. MIL-P-21929—Plastic Material, Cellular Polyurethane, Rigid, Foam-In-Place, Low Density. (3) Federal specifications: TT-P-59—Paint, Ready-Mixed, International...

46 CFR 160.035-1 - Applicable specifications.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Laminates, Fibrous Glass Reinforced, Marine Structural. MIL-P-19644—Plastic Foam, Molded Polystyrene..., Polyester, Low Pressure Laminating, Fire Retardant. MIL-P-21929—Plastic Material, Cellular Polyurethane, Rigid, Foam-In-Place, Low Density. (3) Federal specifications: TT-P-59—Paint, Ready-Mixed, International...

Specifications and Other Standardization Documents Involving Cellular Plastics (Plastic Foams), Cushioning and Related Materials

DTIC Science & Technology

1976-07-01

FOR MEDICAL MATERIAL REQUIRING CONTROLLED TEMPERATURE RANGES 258 PPP-C-1683(1) 8135 69 10 Oct 73 CUSHIONING MATERIAL, EXPANDED POLYSTYRENE LOOSE FILL...Liquid immersion effect on properties of elastoaeric vulcanizates - 45 Lead deflection characteristics - 264 Loose-fill expanded polystyrene - 25f

Printmaking for All Ages

ERIC Educational Resources Information Center

Mitchell, Annette W.

2005-01-01

Foam printing offers all ages and abilities a way to explore textures in the classroom and to develop personal creativity and imagination. Polystyrene foam trays (commonly known as "meat trays") are readily available, inexpensive, lightweight, portable, and receptive to a wide variety of surface treatments. The printmaking process requires only a…

The axial crushes behaviour on foam-filled round Jute/Polyester composite tubes

NASA Astrophysics Data System (ADS)

Othman, A.; Ismail, A. E.

2018-04-01

The present paper investigates the effect of axial loading compression on jute fibre reinforced polyester composite round tubes. The specimen of composite tube was fabricated by hand lay-up method of 120 mm length with fix 50.8 mm inner diameter to determine the behaviour of energy absorption on number of layers of 450 angle fibre and internally reinforced with and without foam filler material. The foam filler material used in this studies were polyurethane (PU) and polystyrene (PE) with average of 40 and 45 kg/m3 densities on the axial crushing load against displacement relations and on the failure modes. The number of layers of on this study were two; three and four were selected to calculate the crush force efficiency (CFE) and the specific energy absorption (SEA) of the composite tubes. Result indicated that the four layers’ jute/polyester show significant value in term of crushing load compared to 2 and 3 layers higher 60% for 2 layer and 3% compared to 3 layers. It has been found that the specific energy absorption of the jute/polyester tubes with polystyrene foam-filled is found higher respectively 10% to 12% than empty and polyurethane (PU) foam tubes. The increase in the number of layers from two to four increases the mean axial load from 1.01 KN to 3.60 KN for empty jute/polyester and from 2.11 KN to 4.26 KN for the polyurethane (PU) foam-filled jute/polyester tubes as well as for 3.60 KN to 5.58 KN for the polystyrene (PE) foam-filled jute/polyester. The author’s found that the failure of mechanism influence the characteristic of curve load against displacement obtained and conclude that an increasing number of layers and introduce filler material enhance the capability of specific absorbed energy.

Precast/Prestressed Concrete Experiments Performance on Non-Load Bearing Sandwich Wall Panels

DTIC Science & Technology

2011-01-01

expanded polystyrene (EPS), extruded expanded polystyrene (XPS...34 Ø Strands @ 14.9 kips 3/8" Ø Strands @ 14.9 kips 9" #3@18" XEPS Insulation Extruded Expanded Polystyrene 4" (Metal C-Pins) Metal C-Pins 1’-8" 3" 3...34 3" 8" 1’-4" 8" 2’-8" 11 2 " 6" 11 2 " 3/8" Ø Strands @ 14.9 kips 3/8" Ø Strands @ 14.9 kips 9" #3@18" XEPS Insulation Extruded Expanded Polystyrene

Building Technology Forecast and Evaluation (BTFE). Volume 2. Evaluation of Two Structural Systems

DTIC Science & Technology

1990-11-01

insulative foam ( expanded polystyrene ) strips between each truss. The assembly is held together with 14-gauge wires welded to the trusses on 2-in. centers...structural load bearing qualities expanded polystyrene . No taping and mudding. Ar. ~J~ .wplrtpd( at each irllnfrnPllo Tile I hin- set or float over

Feasibility of Use of Plastic Foams for Small Vessel Flotation Devices.

DTIC Science & Technology

1976-01-01

waterproofing agents, namely, Dow Corning Silicone 200 fluid, zinc stearate, sodium silicate, Fisher Bath Wax , Carnauba wax , and paraffin wax . Some of...these materials (e.g., waxes ) did not mix well with the foam solution. None of these materials was effective in preventing water absorption by polystyrene

10 CFR 431.303 - Materials incorporated by reference.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Transmission Properties by Means of the Heat Flow Meter Apparatus, approved May 1, 2004, IBR approved for § 431... insulation products for buildings—Factory made products of extruded polystyrene foam (XPS)—Specification..., (“DIN EN 13165”), Thermal insulation products for buildings—Factory made rigid polyurethane foam (PUR...

45 CFR 671.12 - Waste disposal.

Code of Federal Regulations, 2014 CFR

2014-10-01

... chloride (PVC), polyurethane foam, polystyrene foam, rubber and lubricating oils, treated timbers and other... onto ice-free areas or into any fresh water system. (h) Open burning of wastes is prohibited at all... dispose of waste by open burning prior to March 1, 1994, allowance shall be made for the wind direction...

45 CFR 671.12 - Waste disposal.

Code of Federal Regulations, 2013 CFR

2013-10-01

... chloride (PVC), polyurethane foam, polystyrene foam, rubber and lubricating oils, treated timbers and other... onto ice-free areas or into any fresh water system. (h) Open burning of wastes is prohibited at all... dispose of waste by open burning prior to March 1, 1994, allowance shall be made for the wind direction...

45 CFR 671.12 - Waste disposal.

Code of Federal Regulations, 2011 CFR

2011-10-01

... chloride (PVC), polyurethane foam, polystyrene foam, rubber and lubricating oils, treated timbers and other... onto ice-free areas or into any fresh water system. (h) Open burning of wastes is prohibited at all... dispose of waste by open burning prior to March 1, 1994, allowance shall be made for the wind direction...

45 CFR 671.12 - Waste disposal.

Code of Federal Regulations, 2010 CFR

2010-10-01

... chloride (PVC), polyurethane foam, polystyrene foam, rubber and lubricating oils, treated timbers and other... onto ice-free areas or into any fresh water system. (h) Open burning of wastes is prohibited at all... dispose of waste by open burning prior to March 1, 1994, allowance shall be made for the wind direction...

45 CFR 671.12 - Waste disposal.

Code of Federal Regulations, 2012 CFR

2012-10-01

... chloride (PVC), polyurethane foam, polystyrene foam, rubber and lubricating oils, treated timbers and other... onto ice-free areas or into any fresh water system. (h) Open burning of wastes is prohibited at all... dispose of waste by open burning prior to March 1, 1994, allowance shall be made for the wind direction...

Application of a constant hole volume Sanchez-Lacombe equation of state to mixtures relevant to polymeric foaming.

PubMed

von Konigslow, Kier; Park, Chul B; Thompson, Russell B

2018-06-06

A variant of the Sanchez-Lacombe equation of state is applied to several polymers, blowing agents, and saturated mixtures of interest to the polymer foaming industry. These are low-density polyethylene-carbon dioxide and polylactide-carbon dioxide saturated mixtures as well as polystyrene-carbon dioxide-dimethyl ether and polystyrene-carbon dioxide-nitrogen ternary saturated mixtures. Good agreement is achieved between theoretically predicted and experimentally determined solubilities, both for binary and ternary mixtures. Acceptable agreement with swelling ratios is found with no free parameters. Up-to-date pure component Sanchez-Lacombe characteristic parameters are provided for carbon dioxide, dimethyl ether, low-density polyethylene, nitrogen, polylactide, linear and branched polypropylene, and polystyrene. Pure fluid low-density polyethylene and nitrogen parameters exhibit more moderate success while still providing acceptable quantitative estimations. Mixture estimations are found to have more moderate success where pure components are not as well represented. The Sanchez-Lacombe equation of state is found to correctly predict the anomalous reversal of solubility temperature dependence for low critical point fluids through the observation of this behaviour in polystyrene nitrogen mixtures.

Environmental risks of HBCDD from construction and demolition waste: a contemporary and future issue.

PubMed

Nie, Zhiqiang; Yang, Ziliang; Fang, Yanyan; Yang, Yufei; Tang, Zhenwu; Wang, Xingrun; Die, Qingqi; Gao, Xingbao; Zhang, Fengsong; Wang, Qi; Huang, Qifei

2015-11-01

Hexabromocyclododecane (HBCDD), as one of the most widely used brominated flame retardants (BFRs), is of great concern globally because of its persistence in the environment and negative impacts on humans and animals. HBCDD has been mainly used in flame-retarded expanded (EPS) and extruded (XPS) polystyrene foams for insulation in the construction industry. Most of these products will become a part of the construction and demolition (C&D) waste at the end of their life cycle (30-50 years) which is typically disposed of into landfills or incineration. However, the recycling of this material takes quite a low share compared with landfill and incineration. Consequently, high environmental risks will exist in these disposal approaches due to the HBCDD in C&D waste. Currently, XPS or EPS products containing HBCDD in the construction industry have not reached the end of their life cycle in most countries. Relatively little attention has been paid to this emergency issue by either the government or public. Furthermore, C&D waste is most likely disposed of by direct dumping, simple stacking, or open burning in developing countries. Therefore, this paper highlights the global environmental risks of HBCDD from C&D waste. Areas of research for key problems of HBCDD contained in C&D waste are suggested to help control and finally eliminate the impact.

Demonstration of imaging X-ray Thomson scattering on OMEGA EP.

PubMed

Belancourt, Patrick X; Theobald, Wolfgang; Keiter, Paul A; Collins, Tim J B; Bonino, Mark J; Kozlowski, Pawel M; Regan, Sean P; Drake, R Paul

2016-11-01

Foams are a common material for high-energy-density physics experiments because of low, tunable densities, and being machinable. Simulating these experiments can be difficult because the equation of state is largely unknown for shocked foams. The focus of this experiment was to develop an x-ray scattering platform for measuring the equation of state of shocked foams on OMEGA EP. The foam used in this experiment is resorcinol formaldehyde with an initial density of 0.34 g/cm 3 . One long-pulse (10 ns) beam drives a shock into the foam, while the remaining three UV beams with a 2 ns square pulse irradiate a nickel foil to create the x-ray backlighter. The primary diagnostic for this platform, the imaging x-ray Thomson spectrometer, spectrally resolves the scattered x-ray beam while imaging in one spatial dimension. Ray tracing analysis of the density profile gives a compression of 3 ± 1 with a shock speed of 39 ± 6 km/s. Analysis of the scattered x-ray spectra gives an upper bound temperature of 20 eV.

Boring crustaceans damage polystyrene floats under docks polluting marine waters with microplastic.

PubMed

Davidson, Timothy M

2012-09-01

Boring isopods damage expanded polystyrene floats under docks and, in the process, expel copious numbers of microplastic particles. This paper describes the impacts of boring isopods in aquaculture facilities and docks, quantifies and discusses the implications of these microplastics, and tests if an alternate foam type prevents boring. Floats from aquaculture facilities and docks were heavily damaged by thousands of isopods and their burrows. Multiple sites in Asia, Australia, Panama, and the USA exhibited evidence of isopod damage. One isopod creates thousands of microplastic particles when excavating a burrow; colonies can expel millions of particles. Microplastics similar in size to these particles may facilitate the spread of non-native species or be ingested by organisms causing physical or toxicological harm. Extruded polystyrene inhibited boring, suggesting this foam may prevent damage in the field. These results reveal boring isopods cause widespread damage to docks and are a novel source of microplastic pollution. Copyright © 2012 Elsevier Ltd. All rights reserved.

21 CFR 178.3010 - Adjuvant substances used in the manufacture of foamed plastics.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Limitations Azodicarbonamide For use as a blowing agent in pol-yethylene complying with item 2.1 in § 177.1520...-Difluoroethane (CAS Reg. No. 75-37-6) For use as a blowing agent in polystyrene. Isopentane For use as a blowing agent in polystyrene. n-Pentane Do. 1,1,2,2-Tetra-chloroethylene For use only as a blowing agent...

Manufacturing and Characterization of Temperature-Stable, Novel, Viscoelastic Polyurea Based Foams for Impact Management

NASA Astrophysics Data System (ADS)

Ramirez, Brian Josue

The aim of this thesis was to develop advance, high performance polyurea foams for multi-hit capability in protective equipment that respond over a range of impact energies, temperatures, and strain rates. In addition, the microstructure of these materials should be tunable such that the peak stress (or force) transmitted across the foam section can be limited to a specific value defined by an injury threshold while maximizing impact energy absorption. Novel polyurea foams were manufactured and found to exhibit a reversible viscoelastic shear deformation at the molecular level. The intrinsic shear dissipation process is synergistically coupled to controlled collapse of a novel pore structure. The microstructure compromises of stochastic polyhedral cells ranging from 200 - 500 mum with perforated membranes with small apertures ( 20 mum). This makes them strain rate sensitive as the rate at which the air escapes the cells depend upon the loading rate. These mechanisms operate simultaneously and sequentially, thereby significantly reducing the transmitted impact forces across the foam section. Thus, they behave as an elastically modulated layered composite because the cells stiffen or soften in response to the changing loading rate. Therefore, the newly developed polyurea foams are able to manage the varying material strain rate that occurs within the same loading event without the need to modulate the stiffness or density. Additionally, polyurea foams were found to retain its excellent impact properties over a range of temperatures (0°C to 40°C) by having a glass transition temperature well below 0°C. This is in contrast to commercially available high performance foams that have the glass transition temperature near 0°C and absorb energy through phase transformation at ambient conditions, but significantly stiffen at lower temperatures, and dramatically soften at higher temperatures. This expands the application domain of polyurea foam material considerably as it can be tailored to withstand a range of dynamic forces and impact velocities, showing further improvement over currently used protective foams. This thesis also presents a new composite foam concept that involves infiltrating a polyurea-based foam through an open 3D lattice structure with a truss-like network of 2 mm-size struts. The combination of dynamic buckling at the macro (preform lattice struts) and the micro (foam pores) levels increases the stiffness and plateau strength of the composite polyurea foam. The composite foams absorb more impact energy in same section thickness, while keeping both the peak stress and impulse duration low compared to high performance expanded polystyrene (EPS) and Poron foam technology, but without the material crushing or undergoing phase shift, respectively. Most importantly, the composite foams display stability at both low (0°C) and high temperatures (40°C) because of its extremely low Tg of -50°C. Being viscoelastic, they recover fully within 30 s after each impact, without loss of any energy absorption capability. These properties should allow these materials to have a wide range of military and civilian applications, especially in advance armors and protective body and headgear systems.

Part I: In-situ fluorometric quantification of microalgal neutral lipids. Part II: Thermal degradation behavior of investment casting polymer patterns

NASA Astrophysics Data System (ADS)

Zhao, Hongfang

Research described in this dissertation covers two topics. Part-I is focused on in-situ determination of neutral lipid content of microalgae using a lipophilic fluorescent dye. The traditional Nile red stain-based method for detecting microalgal intracellular lipids is limited due to varying composition and thickness of rigid cell walls. In this study, the addition of dilute acid and heating of solution, were found to greatly enhance staining efficiency of Nile red for microalgal species evaluated. Oil-in-water (O/W) microemulsion stabilized by a non-ionic surfactant was employed as a pseudo-standard that mimics lipid-bearing microalgal cells suspended in water. The average neutral lipid contents determined were very close to the results obtained by traditional gravimetric method and solid phase extraction. Part II of the dissertation explores thermo-physico-chemical properties of polymeric pattern materials, including expanded polystyrene (EPS) foam, polyurethane foam, and epoxy stereolithography (SLA) patterns, that are used in investment casting. Density, elastic modulus, expansion coefficient, thermal degradation behavior, etc. were experimentally investigated for their effects on metal casting quality. The reduction in toxic hydrogen cyanide (HCN) generated during thermal decomposition of polyurethane pattern was achieved by increasing either oxidant level or residence time in heated zone. Thermal degradation kinetics of the pattern materials were examined with a thermogravimetric analysis and activation energies were determined by Kissinger and Flynn-Wall-Ozawa methods.

Hydrodynamics of wet foams

NASA Astrophysics Data System (ADS)

Langevin, Dominique; Saint-Jalmes, Arnaud; Marze, Sébastien; Cox, Simon; Hutzler, Stefan; Drenckhan, Wiebke; Weaire, Denis; Caps, Hervé; Vandewalle, Nicolas; Adler, Micheàle; Pitois, Olivier; Rouyer, Florence; Cohen-Addad, Sylvie; Höhler, Reinhard; Ritacco, Hernan

2005-10-01

Foams and foaming pose important questions and problems to the chemical industry. As a material, foam is unusual in being a desired product while also being an unwanted byproduct within industry. Liquid foams are an essential part of gas/liquid contacting processes such as distillation and absorption, but over-production of foam in these processes can lead to downtime and loss of efficiency. Solid polymeric foams, such as polystyrene and polyurethane, find applications as insulation panels in the construction industry. Their combination of low weight and unique elastic/plastic properties make them ideal as packing and cushioning materials. Foams made with proteins are extensively used in the food industry. Despite the fact that foam science is a rapidly maturing field, critical aspects of foam physics and chemistry remain unclear. Several gaps in knowledge were identified to be tackled as the core of this MAP project. In addition, microgravity affords conditions for extending our understanding far beyond the possibilities offered by ground-based investigation. This MAP project addresses the challenges posed by the physics of foams under microgravity.

Seismic Performance of Composite Shear Walls Constructed Using Recycled Aggregate Concrete and Different Expandable Polystyrene Configurations.

PubMed

Liu, Wenchao; Cao, Wanlin; Zhang, Jianwei; Qiao, Qiyun; Ma, Heng

2016-03-02

The seismic performance of recycled aggregate concrete (RAC) composite shear walls with different expandable polystyrene (EPS) configurations was investigated. Six concrete shear walls were designed and tested under cyclic loading to evaluate the effect of fine RAC in designing earthquake-resistant structures. Three of the six specimens were used to construct mid-rise walls with a shear-span ratio of 1.5, and the other three specimens were used to construct low-rise walls with a shear-span ratio of 0.8. The mid-rise and low-rise shear walls consisted of an ordinary recycled concrete shear wall, a composite wall with fine aggregate concrete (FAC) protective layer (EPS modules as the external insulation layer), and a composite wall with sandwiched EPS modules as the insulation layer. Several parameters obtained from the experimental results were compared and analyzed, including the load-bearing capacity, stiffness, ductility, energy dissipation, and failure characteristics of the specimens. The calculation formula of load-bearing capacity was obtained by considering the effect of FAC on composite shear walls as the protective layer. The damage process of the specimen was simulated using the ABAQUS Software, and the results agreed quite well with those obtained from the experiments. The results show that the seismic resistance behavior of the EPS module composite for shear walls performed better than ordinary recycled concrete for shear walls. Shear walls with sandwiched EPS modules had a better seismic performance than those with EPS modules lying outside. Although the FAC protective layer slightly improved the seismic performance of the structure, it undoubtedly slowed down the speed of crack formation and the stiffness degradation of the walls.

Seismic Performance of Composite Shear Walls Constructed Using Recycled Aggregate Concrete and Different Expandable Polystyrene Configurations

PubMed Central

Liu, Wenchao; Cao, Wanlin; Zhang, Jianwei; Qiao, Qiyun; Ma, Heng

2016-01-01

The seismic performance of recycled aggregate concrete (RAC) composite shear walls with different expandable polystyrene (EPS) configurations was investigated. Six concrete shear walls were designed and tested under cyclic loading to evaluate the effect of fine RAC in designing earthquake-resistant structures. Three of the six specimens were used to construct mid-rise walls with a shear-span ratio of 1.5, and the other three specimens were used to construct low-rise walls with a shear-span ratio of 0.8. The mid-rise and low-rise shear walls consisted of an ordinary recycled concrete shear wall, a composite wall with fine aggregate concrete (FAC) protective layer (EPS modules as the external insulation layer), and a composite wall with sandwiched EPS modules as the insulation layer. Several parameters obtained from the experimental results were compared and analyzed, including the load-bearing capacity, stiffness, ductility, energy dissipation, and failure characteristics of the specimens. The calculation formula of load-bearing capacity was obtained by considering the effect of FAC on composite shear walls as the protective layer. The damage process of the specimen was simulated using the ABAQUS Software, and the results agreed quite well with those obtained from the experiments. The results show that the seismic resistance behavior of the EPS module composite for shear walls performed better than ordinary recycled concrete for shear walls. Shear walls with sandwiched EPS modules had a better seismic performance than those with EPS modules lying outside. Although the FAC protective layer slightly improved the seismic performance of the structure, it undoubtedly slowed down the speed of crack formation and the stiffness degradation of the walls. PMID:28773274

Bonding and Sealing Evaluations for Cryogenic Tanks

NASA Technical Reports Server (NTRS)

Glass, David E.

1997-01-01

Several different cryogenic tank concepts are being considered for reusable launch vehicles (RLV'S) . Though different tank concepts are being considered, many will require that the cryogenic insulation be evacuated and be bonded to a structure. In this work, an attempt was made to evaluate the effectiveness of maintaining a vacuum on a specimen where foam or honeycomb core was encased within Gr/Ep. In addition to these tests, flatwise adhesion pull off tests were performed at room temperature with PR 1664, EA 9394, FM-300, Crest 3170, and HT 435 adhesives. The materials bonded included Gr/Ep, Gr/BMI, Al, and stainless steel facesheets, and Ti honeycomb, Hexcel honeycomb, and Rohacell foam core materials.

Thermal conductivity and combustion properties of wheat gluten foams.

PubMed

Blomfeldt, Thomas O J; Nilsson, Fritjof; Holgate, Tim; Xu, Jianxiao; Johansson, Eva; Hedenqvist, Mikael S

2012-03-01

Freeze-dried wheat gluten foams were evaluated with respect to their thermal and fire-retardant properties, which are important for insulation applications. The thermal properties were assessed by differential scanning calorimetry, the laser flash method and a hot plate method. The unplasticised foam showed a similar specific heat capacity, a lower thermal diffusivity and a slightly higher thermal conductivity than conventional rigid polystyrene and polyurethane insulation foams. Interestingly, the thermal conductivity was similar to that of closed cell polyethylene and glass-wool insulation materials. Cone calorimetry showed that, compared to a polyurethane foam, both unplasticised and glycerol-plasticised foams had a significantly longer time to ignition, a lower effective heat of combustion and a higher char content. Overall, the unplasticised foam showed better fire-proof properties than the plasticized foam. The UL 94 test revealed that the unplasticised foam did not drip (form droplets of low viscous material) and, although the burning times varied, self-extinguished after flame removal. To conclude both the insulation and fire-retardant properties were very promising for the wheat gluten foam. © 2012 American Chemical Society

Measure Guideline. Transitioning From Three-Coat Stucco to One-Coat Stucco With EPS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brozyna, K.; Davis, G.; Rapport, A.

2012-04-01

This measure guideline has been developed to help builders transition from using a traditional three-coat stucco wall-cladding system to a one-coat stucco wall-cladding system with expanded polystyrene (EPS) insulated sheathing. The one-coat system maintains the look of a traditional stucco system but uses only a base layer and a finish coat over EPS insulation that achieves higher levels of energy efficiency. Potential risks associated with the installation of a one-coat stucco system are addressed in terms of design, installation, and warranty concerns such as cracking and delamination, along with mitigation strategies to reduce these risks.

Presidential Green Chemistry Challenge: 1996 Greener Reaction Conditions Award

EPA Pesticide Factsheets

Presidential Green Chemistry Challenge 1996 award winner, Dow Chemical Company, developed a process to manufacture polystyrene foam sheet packaging that uses carbon dioxide (CO2) as a blowing agent, eliminating CFC-12 and HCFC-22.

Quasi-static axial crushes on woven jute/polyester AA6063T52 composite tubes

NASA Astrophysics Data System (ADS)

Othman, A.; Ismail, AE

2018-04-01

Quasi-static axial loading have been studied in this paper to determine the behaviour of jute/polyester wrapped on aluminium alloy 6063T52. The filler material also was include into crush box specimen, which is polyurethane (PU) and polystyrene (PE) rigid foam at ranging 40 and 45 kg/m3 densities. All specimen profile was fabricated using hand layup techniques and the length of each specimen were fixed at 100 mm as well as diameter and width of the tube at 50.8 mm. The two types of tubular cross-section were studied of round and square thin-walled profiles and the angle of fibre at 450 were analysed for four layers. Thin walled of aluminium was 1.9 mm and end frontal of each specimen of composite were chamfered at 450 to prevent catastrophic failure mode. The specific absorbed energy (SEA) and crush force efficiency (CFE) were analyses for each specimen to see the behaviour on jute/polyester wrapped on metallic structure can give influence the energy management for automotive application. Result show that the four layers’ jute/polyester with filler material show significant value in term of specific absorbed energy compared empty and polyurethane profiles higher 26.66% for empty and 15.19% compared to polyurethane profiles. It has been found that the thin walled square profile of the jute/polyester tubes with polystyrene foam-filled is found higher respectively 27.42% to 13.13% than empty and polyurethane (PU) foam tubes. An introduce filler material onto thin walled composite profiles gave major advantage increases the mean axial load of 31.87% from 32.94 kN to 48.35 kN from empty to polystyrene thin walled round jute/polyester profiles and 31.7% from 23.11 KN to 33.84 kN from empty to polystyrene thin walled square jute/polyester profiles. Failure mechanisms of the axially loaded composite tubes were also observed and discussed.

Water-in-oil Pickering emulsions stabilized by stearoylated microcrystalline cellulose.

PubMed

Pang, Bo; Liu, Huan; Liu, Peiwen; Peng, Xinwen; Zhang, Kai

2018-03-01

Hydrophobic particles with static water contact angles larger than 90° are more like to stabilize W/O Pickering emulsions. In particular, high internal phase Pickering emulsions (HIPEs) are of great interest for diverse applications. However, W/O HIPEs have rarely been realized using sustainable biopolymers. Herein, we used stearoylated microcrystalline cellulose (SMCC) to stabilize W/O Pickering emulsions and especially, W/O HIPEs. Moreover, these W/O HIPEs can be further used as platforms for the preparation of porous materials, such as porous foams. Stearoylated microcrystalline cellulose (SMCC) was prepared by modifying MCC with stearoyl chloride under heterogeneous conditions. Using SMCC as emulsifiers, W/O medium and high internal phase Pickering emulsions (MIPEs and HIPEs) with various organic solvents as continuous phases were prepared using one-step and two-step methods, respectively. Polystyrene (PS) foams were prepared after polymerization of oil phase using HIPEs as templates and their oil/water separation capacity were studied. SMCC could efficiently stabilize W/O Pickering emulsions and HIPEs could only be prepared via the two-step method. The internal phase volume fraction of the SMCC-stabilized HIPEs reached as high as 89%. Diverse internal phase volume fractions led to distinct inner structures of foams with closed or open cells. These macroporous polystyrene (PS) foams demonstrated great potential for the effective absorption of organic solvents from underwater. Copyright © 2017 Elsevier Inc. All rights reserved.

EXCHANGE NETWORK FOR EXPANDED POLYSTYRENE BIO-SHIPPING CONTAINERS

EPA Science Inventory

Creating an exchange network for shipping containers will provide cost savings, reduce waste, and promote sustainability within the biotechnology industry. Success of this program can divert thousands of EPS containers from landfills each year. A successful pilot program wi...

Conducting nanotubes or nanostructures based composites, method of making them and applications

NASA Technical Reports Server (NTRS)

Gupta, Mool C. (Inventor); Yang, Yonglai (Inventor); Dudley, Kenneth L. (Inventor); Lawrence, Roland W. (Inventor)

2013-01-01

An electromagnetic interference (EMI) shielding material includes a matrix of a dielectric or partially conducting polymer, such as foamed polystyrene, with carbon nanotubes or other nanostructures dispersed therein in sufficient concentration to make the material electrically conducting. The composite is formed by dispersing the nanotube material in a solvent in which the dielectric or partially conducting polymer is soluble and mixing the resulting suspension with the dielectric or partially conducting polymer. A foaming agent can be added to produce a lightweight foamed material. An organometallic compound can be added to enhance the conductivity further by decomposition into a metal phase.

Drug delivery properties of macroporous polystyrene solid foams.

PubMed

Canal, Cristina; Aparicio, Rosa Maria; Vilchez, Alejandro; Esquena, Jordi; García-Celma, Maria José

2012-01-01

Polymeric porous foams have been evaluated as possible new pharmaceutical dosage forms. These materials were obtained by polymerization in the continuous phase of highly concentrated emulsions prepared by the phase inversion temperature method. Their porosity, specific surface and surface topography were characterized, and the incorporation and release of active principles was studied using ketoprofen as model lipophilic molecule. Solid foams with very high pore volume, mainly inside macropores, were obtained by this method. The pore morphology of the materials was characterized, and very rough topography was observed, which contributed to their nearly superhydrophobic properties. These solid foams could be used as delivery systems for active principles with pharmaceutical interest, and in the present work ketoprofen was used as a model lipophilic molecule. Drug incorporation and release was studied from solid foam disks, using different concentrations of the loading solutions, achieving a delayed release with short lag-time.

Nano-fibrillated cellulose-hydroxyapatite based composite foams with excellent fire resistance.

PubMed

Guo, Wenwen; Wang, Xin; Zhang, Ping; Liu, Jiajia; Song, Lei; Hu, Yuan

2018-09-01

Thermally insulating materials made from renewable resources are desirable for energy efficient buildings. Traditional petroleum-derived insulating materials such as rigid polyurethane foam and expanded polystyrene display poor flame retardancy and inorganic insulating materials such as silica aerogel are fragile. Herein, we reported a facile approach to prepare cellulose nanofiber (CNF)-hydroxyapatite (HAP) composite foam by a simple freeze-drying process. The resultant HAP-CNF composite foams showed a thermal conductivity in the range of 38.5-39.1 mW/(m K) and very low peak heat release rate (20.4 kW/m 2 ) and total heat release (1.21 MJ/m 2 ). Vertical burning tests also manifested excellent fire resistance and self-extinguishing behaviours. Considering the excellent fire resistance of this composite foam, it is of significance to fire safety solution for buildings insulating materials. Copyright © 2018 Elsevier Ltd. All rights reserved.

The effect of changes in the USF/NASA toxicity screening test method on data from some cellular polymers

NASA Technical Reports Server (NTRS)

Hilado, C. J.; Miller, C. M.

1976-01-01

Rankings of relative toxicity can be markedly affected by changes in test variables. Revision of the USF/NASA toxicity screening test procedure to eliminate the connecting tube and supporting floor and incorporate a 1.0 g sample weight, 200 C starting temperature, and 800 C upper limit temperature for pyrolysis, reversed the rankings of flexible polyurethane and polychloroprene foams, not only in relation to each other, but also in relation to cotton and red oak. Much of the change is attributed to reduction of the distance between the sample and the test animals, and reduction of the sample weight charged. Elimination of the connecting tube increased the relative toxicity of the polyurethane foams. The materials tested were flexible polyurethane foam, without and with fire retardant; rigid polyurethane foam with fire retardant; flexible polychloroprene foam; cotton, Douglas fir, red oak, hemlock, hardboard, particle board, polystyrene, and polymethyl methacrylate.

The compressive behaviour and constitutive equation of polyimide foam in wide strain rate and temperature

NASA Astrophysics Data System (ADS)

Yoshimoto, Akifumi; Kobayashi, Hidetoshi; Horikawa, Keitaro; Tanigaki, Kenichi

2015-09-01

These days, polymer foams, such as polyurethane foam and polystyrene foam, are used in various situations as a thermal insulator or shock absorber. In general, however, their strength is insufficient in high temperature environments because of their low glass transition temperature. Polyimide is a polymer which has a higher glass transition temperature and high strength. Its mechanical properties do not vary greatly, even in low temperature environments. Therefore, polyimide foam is expected to be used in the aerospace industry. Thus, the constitutive equation of polyimide foam that can be applied across a wide range of strain rates and ambient temperature is very useful. In this study, a series of compression tests at various strain rates, from 10-3 to 103 s-1 were carried out in order to examine the effect of strain rate on the compressive properties of polyimide foam. The flow stress of polyimide foam increased rapidly at dynamic strain rates. The effect of ambient temperature on the properties of polyimide foam was also investigated at temperature from - 190 °C to 270°∘C. The flow stress decreased with increasing temperature.

Remediation of heavy hydrocarbon impacted soil using biopolymer and polystyrene foam beads.

PubMed

Wilton, Nicholas; Lyon-Marion, Bonnie A; Kamath, Roopa; McVey, Kevin; Pennell, Kurt D; Robbat, Albert

2018-05-05

A green chemistry solution is presented for the remediation of heavy hydrocarbon impacted soils. The two-phase recovery system relies on a plant-based biopolymer, which releases hydrocarbons from soil, and polystyrene foam beads, which recover them from solids and water. The efficiency of the process was demonstrated by comparisons with control experiments, where water, biopolymer, or beads alone yielded total petroleum hydrocarbon (TPH) reductions of 25%, 52%, and 58%, respectively, compared to 94% when 1.25 mL of 1% biopolymer and 15 mg beads per gram of soil were agitated for 30 min. Reductions in TPH content were substantial regardless of soil fraction, with removals of 97%, 91%, and 75% from sand, silt, and clay size fractions, respectively. Additionally, treatment efficiency was independent of carbon number, C 13 to C 43 , as demonstrated by reductions in both diesel fuel (C 13 -C 28 ) and residual-range organics (C 25 -C 43 ) of ∼90%. Compared to other published polymer- and surfactant-based treatment methods, this system requires less mobilizing agent, sorbent, and mixing time. The remediation process is both efficient and sustainable because the biopolymer is re-useable and sourced from renewable crops and polystyrene beads are obtained from recycled materials. Copyright © 2018 Elsevier B.V. All rights reserved.

Effect of test conditions on relative toxicity rankings of fifteen materials

NASA Technical Reports Server (NTRS)

Hilado, C. J.; Cumming, H. J.

1977-01-01

Fifteen materials were evaluated for relative toxicity of pyrolysis effluents, using different test conditions in the USF methodology. Wool fabrics were consistently among the most toxic materials, and polystyrene and polychloroprene flexible foam were consistently among the least toxic materials.

Advanced Extended Plate and Beam Wall System in a Cold-Climate House

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mallay, Dave; Wiehagen, Joseph; Kochkin, Vladimir

This report presents the design and evaluation of an innovative wall system. This highly insulated (high-R) light-frame wall system for use above grade in residential buildings is referred to as Extended Plate & Beam (EP&B). The EP&B design is the first of its kind to be featured in a new construction test house (NCTH) for the DOE Building America program. The EP&B wall design integrates standard building methods and common building products to construct a high-R wall that minimizes transition risks and costs to builders. The EP&B design combines optimized framing with integrated rigid foam sheathing to increase the wallmore » system's R-value and reduce thermal bridging. The foam sheathing is installed between the wall studs and structural wood sheathing. The exterior wood sheathing is attached directly to a framing extension formed by extended top and bottom plates. The exterior wood sheathing can dry to the exterior and provides bracing, a clear drainage plane and flashing surface for window and door openings, and a nailing surface for siding attachment. With support of the DOE Building America program, Home Innovation Research Labs partnered with Lancaster County Career and Technology Center (LCCTC) to build a NCTH in Lancaster, PA to demonstrate the EP&B wall design in a cold climate (IECC climate zone 5A). The results of the study confirmed the benefits of the systems and the viability of its integration into the house construction process.« less

Improving the quality of polymer-coated urea with recycled plastic, proper additives, and large tablets.

PubMed

Yang, Yue-Chao; Zhang, Min; Li, Yuncong; Fan, Xiao-Hui; Geng, Yu-Qing

2012-11-14

Polymer-coated urea (PCU) has great potential for increasing crop production and enhancing nitrogen (N) fertilizer use efficiency, benefiting the ecosystem. However, current PCUs are used only in a limited market, and the main obstacle to the wider use of PCUs is high cost compared to that of conventional N fertilizers. In this study, the low cost PCU and large tablet polymer-coated urea (LTPCU) were prepared by using recycling polystyrene foam and various sealants as the coating materials. The structural and chemical characteristics of the coating shells of the coated fertilizers were examined. The N release characteristics of coated fertilizers were determined in 25 °C water under laboratory conditions. The relationship between the N release longevity and the amount of coating material and the percentage of different sealants were evaluated. The results indicated that recycling polystyrene foam was the ideal coating material of the controlled release fertilizer. The polyurethane that was synthesized by the reaction of castor oil and isocyanate was better than the wax as the additive to delay the N release rate of coated urea. The coating material used for LTPCU was 70-80% less than those used for commercial PCUs under the same N release longevity. The cost of the recycling polystyrene foam used for coating one ton of pure N of the LTPCU was about one-seventh to one-eighth of the cost of the traditional polymer used for the commercial PCU. The experimental data showed that the LTPCU with good controlled-release capacities, being economical and eco-friendly, could be promising for wide use in agriculture and horticulture.

Measure Guideline: Transitioning from Three-Coat Stucco to One-Coat Stucco with EPS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brozyna, K.; Davis, G.; Rapport, A.

2012-04-01

This Measure Guideline has been developed to help builders transition from using a traditional three-coat stucco wall-cladding system to a one-coat stucco wall-cladding system with expanded polystyrene (EPS) insulated sheathing. The three-coat system uses a base layer, a fill layer, and a finish layer. The one-coat system maintains the look of a traditional stucco system but uses only a base layer and a finish coat over EPS insulation that achieves higher levels of energy efficiency. Potential risks associated with the installation of a one-coat stucco system are addressed in terms of design, installation, and warranty concerns such as cracking andmore » delamination, along with mitigation strategies to reduce these risks.« less

Chain exchange in triblock copolymer micelles

NASA Astrophysics Data System (ADS)

Lu, Jie; Lodge, Timothy; Bates, Frank

2015-03-01

Block polymer micelles offer a host of technological applications including drug delivery, viscosity modification, toughening of plastics, and colloidal stabilization. Molecular exchange between micelles directly influences the stability, structure and access to an equilibrium state in such systems and this property recently has been shown to be extraordinarily sensitive to the core block molecular weight in diblock copolymers. The dependence of micelle chain exchange dynamics on molecular architecture has not been reported. The present work conclusively addresses this issue using time-resolved small-angle neutron scattering (TR-SANS) applied to complimentary S-EP-S and EP-S-EP triblock copolymers dissolved in squalane, a selective solvent for the EP blocks, where S and EP refer to poly(styrene) and poly(ethylenepropylene), respectively. Following the overall SANS intensity as a function of time from judiciously deuterium labelled polymer and solvent mixtures directly probes the rate of molecular exchange. Remarkably, the two triblocks display exchange rates that differ by approximately ten orders of magnitude, even though the solvophobic S blocks are of comparable size. This discovery is considered in the context of a model that successfully explains S-EP diblock exchange dynamics.

Catalytic thermal cracking of post-consumer waste plastics to fuels: Part 1 - Kinetics and optimization

USDA-ARS?s Scientific Manuscript database

Thermogravimetric analysis (TGA) was used to investigate thermal and catalytic pyrolysis of waste plastics such as prescription bottles (polypropylene/PP), high density polyethylene, landfill liners (polyethylene/PE), packing materials (polystyrene/PS), and foams (polyurethane/PU) into crude plastic...

40 CFR Appendix Q to Subpart G of... - Unacceptable Substitutes Listed in the March 28, 2007 Final Rule, Effective May 29, 2007

Code of Federal Regulations, 2014 CFR

2014-07-01

... commercial refrigeration—Rigid polyurethane sandwich panels. HCFC-22; HCFC-142b as substitutes for HCFC-141b... commercial refrigeration, and sandwich panels. —Rigid polyurethane slabstock and other foams. —Polystyrene...

40 CFR Appendix Q to Subpart G of... - Unacceptable Substitutes Listed in the March 28, 2007 Final Rule, Effective May 29, 2007

Code of Federal Regulations, 2013 CFR

2013-07-01

... commercial refrigeration—Rigid polyurethane sandwich panels. HCFC-22; HCFC-142b as substitutes for HCFC-141b... commercial refrigeration, and sandwich panels. —Rigid polyurethane slabstock and other foams. —Polystyrene...

40 CFR Appendix Q to Subpart G of... - Unacceptable Substitutes Listed in the March 28, 2007 Final Rule, Effective May 29, 2007

Code of Federal Regulations, 2012 CFR

2012-07-01

... commercial refrigeration—Rigid polyurethane sandwich panels. HCFC-22; HCFC-142b as substitutes for HCFC-141b... commercial refrigeration, and sandwich panels. —Rigid polyurethane slabstock and other foams. —Polystyrene...

40 CFR Appendix Q to Subpart G of... - Unacceptable Substitutes Listed in the March 28, 2007 Final Rule, Effective May 29, 2007

Code of Federal Regulations, 2011 CFR

2011-07-01

... commercial refrigeration—Rigid polyurethane sandwich panels. HCFC-22; HCFC-142b as substitutes for HCFC-141b... commercial refrigeration, and sandwich panels. —Rigid polyurethane slabstock and other foams. —Polystyrene...

40 CFR Appendix Q to Subpart G of... - Unacceptable Substitutes Listed in the March 28, 2007 Final Rule, Effective May 29, 2007

Code of Federal Regulations, 2010 CFR

2010-07-01

... commercial refrigeration—Rigid polyurethane sandwich panels. HCFC-22; HCFC-142b as substitutes for HCFC-141b... commercial refrigeration, and sandwich panels. —Rigid polyurethane slabstock and other foams. —Polystyrene...

Study of the solubility and stability of polystyrene wastes in a dissolution recycling process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garcia, Maria Teresa; Gracia, Ignacio; Duque, Gema

2009-06-15

Dissolution with suitable solvents is one of the cheapest and more efficient processes for polystyrene waste management. In this work the solubility of polystyrene foams in several solvents benzene, toluene, xylene, tetrahydrofuran, chloroform, 1,3-butanediol, 2-butanol, linalool, geraniol, d-limonene, p-cymene, terpinene, phellandrene, terpineol, menthol, eucalyptol, cinnamaldheyde, nitrobenzene, N,N-dimethylformamide and water has been determined. Experimental results have shown that to develop a 'green process' the constituents of essential oils, d-limonene, p-cymene, terpinene, phellandrene, are the most appropriate solvents. The action of these solvent does not produce any degradation of polymer chains. The solubility of the polymer in the mentioned solvents at differentmore » temperatures has been investigated. The solvent can be easily recycled by distillation.« less

Brominated Flame Retardants: Spatial and Temporal Trends in the Environment and Biota from the Pacific Basin Countries

EPA Science Inventory

Brominated flame retardants (BFRs) are used as additive or reactive components in a variety of polymers including high-impact polystyrene and epoxy resins, commercial products such as computers, electronics and electrical equipment, thermal insulation, textiles and furniture foam...

Glass Fragment Hazard from Windows Broken by Airblast

DTIC Science & Technology

1980-05-30

Reference 2). Velocities, masses, and spetial distributions of frao- ments have been mfeasured by trapping the fragments in Sty.roFoam 0 ( expanded ... polystyrene ) "witness plates located behind windows in houses subjected to large chiemical or nuclear ex- plosions (References 3 and 4). Yields ranged

The Foulness Multiton Air Blast Simulator. Part 3. Blast Wave Formation and Methods Used to Drive the Simulator,

DTIC Science & Technology

1980-03-01

the total energy release of the explosive driver using expanded polystyrene and at the same time, controlling the rate of release. The part played by aqueous foam in minimising irregularities in waveform also is described. (Author)

Some possible reference materials for fire toxicity tests

NASA Technical Reports Server (NTRS)

Hilado, C. J.; Solis, A. N.

1977-01-01

Suitable reference materials need to be selected in order to standardize any test method. The evaluation of cotton, polyethylene, polyether sulfone, polycarbonate, polystyrene, and polyurethane flexible and rigid foams as possible reference materials for the University of San Francisco/NASA toxicity screening test method is discussed.

Effect of colloidal particleson the foamability and stabilization of aqueous foams by cationic surfactant CTAB

NASA Astrophysics Data System (ADS)

Cao, Huiying; Chen, Jiayi; Cai, Jie; Li, Yapin

2017-12-01

Colloidal particles can influence the foamability and stabilization of aqueous foam by addition of surfactant at the air-water interface. This occurs because particles are activated via the interaction with surfactant and are adsorbed onto the surfaces of foams. This phenomenon has been applied extensively to the development of new materials and techniques. Whether particle surface can be activated or not is decided by the interaction between the surfactant and the particle. In this work, we studied the effects of cationic surfactant CTAB (cetyltrimethylammonium bromide) on PS (polystyrene), SiO2, and TiO2 particles in aqueous solution, and compared the difference in their surface activation according to foam volume of the particles/CTAB/water system, and the degrees of foamability and foam stabilization. In addition, the influence of anionic surfactant SDS (sodium dodecyl sulfate) on the surface activation of PS in aqueous solution was also analyzed and compared with that of CTAB.

Building America Case Study: Advanced Extended Plate and Beam Wall System in a Cold-Climate House, Mount Joy, Pennsylvania

DOE Office of Scientific and Technical Information (OSTI.GOV)

This report presents the design and evaluation of a innovative wall system. This highly insulated (high-R) light-frame wall system for use above grade in residential buildings is referred to as Extended Plate & Beam (EP&B). The EP&B design is the first of its kind to be featured in a new construction test house (NCTH) for the DOE Building America program. The EP&B wall design integrates standard building methods and common building products to construct a high-R wall that minimizes transition risks and costs to builders. The EP&B design combines optimized framing with integrated rigid foam sheathing to increase the wallmore » system's R-value and reduce thermal bridging. The foam sheathing is installed between the wall studs and structural wood sheathing. The exterior wood sheathing is attached directly to a framing extension formed by extended top and bottom plates. The exterior wood sheathing can dry to the exterior and provides bracing, a clear drainage plane and flashing surface for window and door openings, and a nailing surface for siding attachment. With support of the DOE Building America program, Home Innovation Research Labs partnered with Lancaster County Career and Technology Center (LCCTC) to build a NCTH in Lancaster, PA to demonstrate the EP&B wall design in a cold climate (IECC climate zone 5A). The results of the study confirmed the benefits of the systems and the viability of its integration into the house construction process.« less

Metabolsim of a-and y~Hexabromocylododecane and Enantioselective Fractions of a-, B-, y-Isomers in Mice.

EPA Science Inventory

Hexabromocyclododecane (HBCD) is the third-highest production volume brominated flame retardant (BFR). It is incorporated into expanded polystyrene foam used in thermal insulation of buildings, and currently is the only suitable BFR for this application. HBCD is an additive flame...

Comparison of the cytotoxic effect of polystyrene latex nanoparticles on planktonic cells and bacterial biofilms

NASA Astrophysics Data System (ADS)

Nomura, Toshiyuki; Fujisawa, Eri; Itoh, Shikibu; Konishi, Yasuhiro

2016-06-01

The cytotoxic effect of positively charged polystyrene latex nanoparticles (PSL NPs) was compared between planktonic bacterial cells and bacterial biofilms using confocal laser scanning microscopy, atomic force microscopy, and a colony counting method. Pseudomonas fluorescens, which is commonly used in biofilm studies, was employed as the model bacteria. We found that the negatively charged bacterial surface of the planktonic cells was almost completely covered with positively charged PSL NPs, leading to cell death, as indicated by the NP concentration being greater than that required to achieve single layer coverage. In addition, the relationship between surface coverage and cell viability of P. fluorescens cells correlated well with the findings in other bacterial cells ( Escherichia coli and Lactococcus lactis). However, most of the bacterial cells that formed the biofilm were viable despite the positively charged PSL NPs being highly toxic to planktonic bacterial cells. This indicated that bacterial cells embedded in the biofilm were protected by self-produced extracellular polymeric substances (EPS) that provide resistance to antibacterial agents. In conclusion, mature biofilms covered with EPS exhibit resistance to NP toxicity as well as antibacterial agents.

Microscale synthesis and characterization of polystyrene: NSF-POLYED scholars project

NASA Technical Reports Server (NTRS)

Quaal, Karen S.; Wu, Chang-Ning

1994-01-01

Polystyrene is a familiar polymer with many commercial uses. Its applications range from the clear, high index of refraction, brittle plastic used to form audio cassette and CD cases to the foamed material used in insulated drink cups and packaging material. Polystyrene constitutes 11 percent of the plastics used in packaging with only High Density Polyethylene (HDPE) and Low Density Polyethylene (LDPE) contributing a larger share: so much polystyrene is used today, it is one of six common plastics that manufacturers have assigned an identification code. The code helps recycling efforts. Polystyrene's code is (PS code 6). During the summer and fall of 1992 several new polymeric experiments were developed by the NSF POLYED Scholars for introduction into the chemistry core curriculum. In this presentation, one such project will be discussed. This laboratory project is recommended for a first or second year laboratory course allowing the introduction of polymeric science to undergraduates at the earliest opportunity. The reliability of the experiments which make up this project and the recognition factor of polystyrene, a material we come in contact with everyday, makes the synthesis and characterization of polystyrene a good choice for the introduction of polymerization to undergraduates. This laboratory project appeals to the varied interests of students enrolled in the typical first year chemistry course and becomes an ideal way to introduce polymers to a wide variety of science and engineering students.

Soil Moisture Active and Passive (SMAP) White-Painted Expanded Polystyrene (EPS) Radome Survivability Test

NASA Technical Reports Server (NTRS)

Mikhaylov, Rebecca; Kwack, Eug; Stegman, Matthew; Dawson, Douglas; Hoffman, Pamela

2015-01-01

NASA's SMAP Mission launched in January 2015 into a 685 km near-polar, sun-synchronous orbit. The SMAP instrument architecture incorporates an L-band radar and radiometer which share a common feedhorn and mesh reflector. The instrument rotates about the nadir axis at approximately 15 rpm, thereby providing a conically scanning wide swath antenna beam that is capable of achieving global coverage within three days. The radiometer and its associated electronics have tight thermal stability requirements in order to meet the required surface emittance measurement precision from space. Maintaining the thermal stabilities is quite challenging because the radiometer is located on a spinning platform that can either be in full sunlight or eclipse, and thus exposed to a highly transient environment. Stability requirements were met by integrating a light-weight Expanded Polystyrene (EPS) radome into the design to prevent solar illumination of the feed horn interior. The radome was painted white since the thermo-optical properties of bare sunlit EPS degrade rapidly over the three-year mission. Milling of the EPS and solvent within the white paint created cavities on the EPS surface which may introduce localized hot spots possibly violating the EPS glass transition temperature of 96degC and leading to structural integrity concerns. A three-day thermal test was conducted in a vacuum chamber to verify survivability of the radome during a simulated non-spin fault condition at end of mission. A portable solar simulator illuminated the test article and the beam irradiance was kept nearly constant during the entire 50 hour test, except during the first hour which simulated the expected 79degC on-orbit surface temperature of the radome. The test article survived based on the established pass criteria for three separate metrics: dimensional, optical property, and color. If any hot spots exist locally, they did not cause any observable permanent deformation when compared to pre- and post-test images. The test results increase confidence that there is a high probability that the radome will survive the worst-case scenario of a no-spin fault condition at the end of mission.

DOE Zero Energy Ready Home Case Study: BPC Green Builders — Trolle Residence, Danbury, CT

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2014-09-01

The builder of this 1,650-ft2 cabin won a Custom Home honor in the 2014 Housing Innovations Awards. The home meets Passive House Standards with 5.5-in. of foil-faced polysiocyanurate foam boards lining the outside walls, R-55 of rigid EPS foam under the slab, R-86 of blown cellulose in the attic, triple-pane windows, and a single ductless heat pump to heat and cool the entire home.

76 FR 21579 - Energy Conservation Program: Test Procedures for Walk-In Coolers and Walk-In Freezers

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-15

..., ``Thermal insulation products for buildings--Factory made products of extruded polystyrene foam (XPS)-- Specification,'' approved February 2009. (4) DIN EN 13165:2009-02, ``Thermal insulation products for buildings... 2. Heat Transfer Through Panels 3. Energy Use of Doors 4. Heat Transfer via Air Infiltration 5...

24 CFR 200.947 - Building product standards and certification program for polystyrene foam insulation board.

Code of Federal Regulations, 2010 CFR

2010-04-01

... INTRODUCTION TO FHA PROGRAMS Minimum Property Standards § 200.947 Building product standards and certification... product, the administrator's certification of compliance with the applicable standards and the type of... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Building product standards and...

Transport of polar and non-polar volatile compounds in polystyrene foam and oriented strand board

NASA Astrophysics Data System (ADS)

Yuan, Huali; Little, John C.; Hodgson, Alfred T.

Transport of hexanal and styrene in polystyrene foam (PSF) and oriented strand board (OSB) was characterized. A microbalance was used to measure sorption/desorption kinetics and equilibrium data. While styrene transport in PSF can be described by Fickian diffusion with a symmetrical and reversible sorption/desorption process, hexanal transport in both PSF and OSB exhibited significant hysteresis, with desorption being much slower than sorption. A porous media diffusion model that assumes instantaneous local equilibrium governed by a nonlinear Freundlich isotherm was found to explain the hysteresis in hexanal transport. A new nonlinear sorption and porous diffusion emissions model was, therefore, developed and partially validated using independent chamber data. The results were also compared to the more conventional linear Fickian-diffusion emissions model. While the linear emissions model predicts styrene emissions from PSF with reasonable accuracy, it substantially underestimates the rate of hexanal emissions from OSB. Although further research and more rigorous validation is needed, the new nonlinear emissions model holds promise for predicting emissions of polar VOCs such as hexanal from porous building materials.

Conversion of "Waste Plastic" into Photocatalytic Nanofoams for Environmental Remediation.

PubMed

de Assis, Geovania C; Skovroinski, Euzébio; Leite, Valderi D; Rodrigues, Marcelo O; Galembeck, André; Alves, Mary C F; Eastoe, Julian; de Oliveira, Rodrigo J

2018-03-07

Plastic debris is a major environmental concern, and to find effective ways to reuse polystyrene (PS) presents major challenges. Here, it is demonstrated that polystyrene foams impregnated with SnO 2 are easily generated from plastic debris and can be applied to photocatalytic degradation of dyes. SnO 2 nanoparticles were synthesized by a polymeric precursor method, yielding specific surface areas of 15 m 2 /g after heat treatment to 700 °C. Crystallinity, size, and shape of the SnO 2 particles were assessed by X-ray diffraction (XRD) and transmission electron microscopy (TEM), demonstrating the preparation of crystalline spherical nanoparticles with sizes around 20 nm. When incorporated into PS foams, which were generated using a thermally induced phase separation (TIPS) process, the specific surface area increased to 48 m 2 /g. These PS/SnO 2 nanofoams showed very good efficiency for photodegradation of rhodamine B, under UV irradiation, achieving up to 98.2% removal. In addition the PS/SnO 2 nanofoams are shown to retain photocatalytic activity for up to five reuse cycles.

Toxicity of pyrolysis gases from some cellular polymers

NASA Technical Reports Server (NTRS)

Hilado, C. J.; Machado, A. M.

1978-01-01

Various samples of cellular polymers were evaluated for toxicity of pyrolysis gases, using the screening test method developed at the University of San Francisco. The cellular polymer samples included polyimide, polymethacrylimide, polybismaleimide, polyurethane, polyisocyanurate, polyethylene, polychloroprene, polyvinyl chloride, polystyrene, polysiloxane, and polyphosphazene. The cellular polymers exhibited varying levels of toxicity under these test conditions. Among the rigid cellular polymers, times to death were shortest with the imide type foams and longest with polyvinyl chloride and polystyrene. Among the flexible cellular polymers, times to death were shortest with polyimide and polyester, and longest with polychloroprene and polysiloxane. Increased char yield was not necessarily associated with reduced toxicity.

Controllable growth of polyaniline nanowire arrays on hierarchical macro/mesoporous graphene foams for high-performance flexible supercapacitors

NASA Astrophysics Data System (ADS)

Yu, Pingping; Zhao, Xin; Li, Yingzhi; Zhang, Qinghua

2017-01-01

Free-standing hierarchical macro/mesoporous flexible graphene foam have been constructed by rational intergration ofwell dispersed graphene oxide sheets and amino-modified polystyrene (PS) spheres through a facile ;templating and embossing; technique. The three dimensional (3D) macro/mesoporous flexible graphene foam not only inherits the uniform porous structures of graphene foam, but also contains hierarchical macro/mesopores on the struts by sacrificing PS spheres and the activation of KOH, which could providing rapid pathways for ionic and electronic transport to high specific capacitance. Vertically polyaniline (PANI) nanowire arrays are then uniformly deposited onto the hierarchical macro/mesoporous graphene foam(fRGO-F/PANI) by a simple in situ polymerization, which show a high specific capacitance of 939 F g-1. Thanks to the synergistic function of 3D bicontinuous hierarchical porous structure of graphene foam and effective immobilization of PANI nanowires on the struts, the assembled symmetric supercapctior with fRGO-F/PANI as electrodes exhibits a maximum energy density and power density of 20.9 Wh kg-1 and 103.2 kW kg-1, respectively. Moreover, it also displays an excellent cyclic stability with a 88.7% retention after 5000 cycles.

Convergent Geometry Foam Buffered Direct Drive Experiments*

NASA Astrophysics Data System (ADS)

Watt, R. G.; Wilson, D. C.; Hollis, R. V.; Gobby, P. L.; Chrien, R. E.; Mason, R. J.; Kopp, R. A.; Willi, O.; Iwase, A.; Barringer, L. H.; Gaillard, R.; Kalantar, D. H.; Lerche, R. A.; MacGowan, B.; Nelson, M.; Phillips, T.; Knauer, J. P.; McKenty, P. W.

1996-11-01

A serious concern for directly driven ICF implosions is the asymmetry imparted to the capsule by laser drive non-uniformities, particularly the ``early time imprint'' remaining despite the use of random phase plates and smoothing with spectral dispersion. The use of a foam buffer has been proposed as a means to reduce this imprint. Two types of convergent geometry tests of the technique to correct static nonuniformities have been studied to date; cylindrical implosions at the Trident and Vulcan lasers, and spherical implosions at the NOVA laser, all using 527 nm laser drive. Cylindrical implosions used end on x-ray backlighter imaging of inner surface disruption due an intentional hole in the drive footprint, using 50 mg/cc acyrlate foam with a thin Au preheat layer. Spherical implosions used 50 mg/cc polystyrene foam plus Au to study yield and imploded core symmetry of capsules with and without a foam buffer, in comparison to ``clean 1D'' calculations. For thick enough layers, all cases showed improvement. Details of the experiments and theoretical unpinnings will be shown. *Work performed under US DOE Contract No. W-7405-Eng-36.

Foam, a promising vehicle to deliver nanoparticles for vadose zone remediation.

PubMed

Shen, Xin; Zhao, Lin; Ding, Yuanzhao; Liu, Bo; Zeng, Hui; Zhong, Lirong; Li, Xiqing

2011-02-28

Foam delivery of remedial amendments for in situ immobilization of deep vadose zone contaminants can overcome the intrinsic problems associated with solution-based delivery, such as preferential flow and contaminant mobilization. In this work, the feasibility of using foam to deliver nanoparticles in unsaturated porous media was investigated. Carboxyl-modified polystyrene latex microspheres were used as surrogates for nanoparticles of remediation purposes. Foams generated from the solutions of six commonly available surfactants all had excellent abilities to carry the microspheres. The presence of the microspheres did not reduce the stabilities of the foams. When microsphere-laden foam was injected through the unsaturated columns, the fractions of microspheres exiting the column were much higher than that when the microsphere water suspensions were injected through the columns. The enhanced microsphere transport implies that foam delivery could significantly increase the radius of influence of injected nanoparticles of remediation purposes. Reduced tension at air-water interfaces by the surfactant and increased driving forces imparted on the microspheres at the interfaces by the flowing foam bubbles may have both contributed to the enhanced transport. Preliminary tests also demonstrated that foam can carry significant fractions of zero valent iron nanoparticles at concentrations relevant to field remediation conditions (up to 5.3 g L(-1)). As such, this study demonstrates that surfactant foam is potentially a promising vehicle to deliver nanoparticles for vadose zone remediation. Copyright © 2010 Elsevier B.V. All rights reserved.

Study on Thermal Conductivities of Aromatic Polyimide Aerogels.

PubMed

Feng, Junzong; Wang, Xin; Jiang, Yonggang; Du, Dongxuan; Feng, Jian

2016-05-25

Polyimide aerogels for low density thermal insulation materials were produced by 4,4'-diaminodiphenyl ether and 3,3',4,4'-biphenyltetracarboxylic dianhydride, cross-linked with 1,3,5-triaminophenoxybenzene. The densities of obtained polyimide aerogels are between 0.081 and 0.141 g cm(-3), and the specific surface areas are between 288 and 322 m(2) g(-1). The thermal conductivities were measured by a Hot Disk thermal constant analyzer. The value of the measured thermal conductivity under carbon dioxide atmosphere is lower than that under nitrogen atmosphere. Under pressure of 5 Pa at -130 °C, the thermal conductivity is the lowest, which is 8.42 mW (m K)(-1). The polyimide aerogels have lower conductivity [30.80 mW (m K)(-1)], compared to the value for other organic foams (polyurethane foam, phenolic foam, and polystyrene foam) with similar apparent densities under ambient pressure at 25 °C. The results indicate that polyimide aerogel is an ideal insulation material for aerospace and other applications.

Active Solar Energy System Design, Installation and Maintenance Manual.

DTIC Science & Technology

1986-04-01

3.03 400 Fiberglass, pipe 3.45 350 Polystyrene, extruded 5.00 170 Polyureathane 6.25 210 Foam Rubber 4.35 150 In selecting a particular insulation...sandwich & snack shops Apartment Houses (number of apartments): 20 or Less 42.0 gal/apartment 50 40.0 gal/apartment 75 38.0 gal/apartment 100 37.0 gal

Fungal mycelium and cotton plant materials in the manufacture of biodegradable molded packaging material: Evaluation study of select blends of cotton byproducts

USDA-ARS?s Scientific Manuscript database

The primary material used by the packaging industry is extruded polystyrene foam, which is commonly marketed as Styrofoam™. In its original formulation, Styrofoam™ is resistant to photolysis and effectively does not decompose. The light weight of Styrofoam™ packaging materials reduces the likelihood...

Synthesis of nanostructured/macroscopic low-density copper foams based on metal-coated polymer core–shell particles [Templated synthesis of nanowalled low-density copper foams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Sung Ho; Bazin, Nick; Shaw, Jessica I.

A robust, millimeter-sized low-density Cu foam with ~90% (v/v) porosity, ~30 nm thick walls, and ~1 μm diameter spherical pores is prepared by the slip-casting of metal-coated polymer core–shell particles followed by a thermal removal of the polymer. In this paper, we report our key findings that enable the development of the low-density Cu foams. First, we need to synthesize polystyrene (PS) particles coated with a very thin Cu layer (in the range of tens of nanometers). A simple reduction in the amount of Cu deposited onto the PS was not sufficient to form such a low-density Cu foams duemore » to issues related to foam collapse and densification upon the subsequent polymer removal step. Precise control over the morphology of the Cu coating on the particles is essential for the synthesis of a lower density of foams. Second, improving the dispersion of PS–Cu particles in a suspension used for the casting as well as careful optimization of a baking condition minimize the formation of irregular large voids, leading to Cu foams with a more uniform packing and a better connectivity of neighboring Cu hollow shells. Finally, we analyzed mechanical properties of the Cu foams with a depth-sensing indentation test. The uniform Cu foams show a significant improvement in mechanical properties (~1.5× modulus and ~3× hardness) compared to those of uncontrolled foam samples with a similar foam density but irregular large voids. As a result, higher surface areas and a good electric conductivity of the Cu foams present a great potential to future applications.« less

Synthesis of nanostructured/macroscopic low-density copper foams based on metal-coated polymer core–shell particles [Templated synthesis of nanowalled low-density copper foams

DOE PAGES

Kim, Sung Ho; Bazin, Nick; Shaw, Jessica I.; ...

2016-12-06

A robust, millimeter-sized low-density Cu foam with ~90% (v/v) porosity, ~30 nm thick walls, and ~1 μm diameter spherical pores is prepared by the slip-casting of metal-coated polymer core–shell particles followed by a thermal removal of the polymer. In this paper, we report our key findings that enable the development of the low-density Cu foams. First, we need to synthesize polystyrene (PS) particles coated with a very thin Cu layer (in the range of tens of nanometers). A simple reduction in the amount of Cu deposited onto the PS was not sufficient to form such a low-density Cu foams duemore » to issues related to foam collapse and densification upon the subsequent polymer removal step. Precise control over the morphology of the Cu coating on the particles is essential for the synthesis of a lower density of foams. Second, improving the dispersion of PS–Cu particles in a suspension used for the casting as well as careful optimization of a baking condition minimize the formation of irregular large voids, leading to Cu foams with a more uniform packing and a better connectivity of neighboring Cu hollow shells. Finally, we analyzed mechanical properties of the Cu foams with a depth-sensing indentation test. The uniform Cu foams show a significant improvement in mechanical properties (~1.5× modulus and ~3× hardness) compared to those of uncontrolled foam samples with a similar foam density but irregular large voids. As a result, higher surface areas and a good electric conductivity of the Cu foams present a great potential to future applications.« less

Thermal Smoothing by Laser-Produced Plasma of Porous Matter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalal, M.; Limpouch, J.; Krousky, E.

2003-05-15

Efficient energy transfer and smoothing effect in laser-irradiated polystyrene foam targets have been observed in preliminary experiments on the PALS iodine laser facility. A theory of laser light absorption region formation and ablation pressure generation in laser-produced plasma of porous matter has been developed and applied for discussion of the results obtained. In particular, two stages of homogenization of the porous matter, important for comprehension of the anomalously high absorption of laser radiation in supercritical foam matter, have been identified: the first, a considerably fast stage of partial homogenization, followed by a much slower second stage, leading to a uniformmore » medium.« less

Antifouling Properties of a Self-Assembling Glutamic Acid-Lysine Zwitterionic Polymer Surface Coating.

PubMed

Ziemba, Christopher; Khavkin, Maria; Priftis, Dimitris; Acar, Handan; Mao, Jun; Benami, Maya; Gottlieb, Moshe; Tirrell, Matthew; Kaufman, Yair; Herzberg, Moshe

2018-04-23

There is a need for the development of antifouling materials to resist adsorption of biomacromolecules. Here we describe the preparation of a novel zwitterionic block copolymer with the potential to prevent or delay the formation of microbial biofilms. The block copolymer comprised a zwitterionic (hydrophilic) section of alternating glutamic acid (negatively charged) and lysine (positively charged) units and a hydrophobic polystyrene section. Cryo-TEM and dynamic-light-scattering (DLS) results showed that, on average, the block copolymer self-assembled into 7-nm-diameter micelles in aqueous solutions (0 to 100 mM NaCl, pH 6). Quartz crystal microbalance with dissipation monitoring (QCM-D), atomic force microscopy (AFM), and contact angle measurements demonstrated that the block copolymer self-assembled into a brush-like monolayer on polystyrene surfaces. The brush-like monolayer produced from a 100 mg/L block copolymer solution exhibited an average distance, d, of approximately 4-8 nm between each block copolymer molecule (center to center). Once the brush-like monolayer self-assembled, it reduced EPS adsorption onto the polystyrene surface by ∼70% (mass), reduced the rate of bacterial attachment by >80%, and inhibited the development of thick biofilms. QCM-D results revealed that the EPS molecules penetrate between the chains of the brush and adsorb onto the polystyrene surface. Additionally, AFM analyses showed that the brush-like monolayer prevents the adhesion of large (> d) hydrophilic colloids onto the surface via hydration repulsion; however, molecules or colloids small enough to fit between the brush polymers (< d) were able to be adsorbed onto the surface via van der Waals interactions. Overall, we found that the penetration of extracellular organelles, as well as biopolymers through the brush, is critical for the failure of the antifouling coating, and likely could be prevented through tuning of the brush density. Stability and biofilm development testing on multiple surfaces (polypropylene, glass, and stainless steel) support practical applications of this novel block copolymer.

Designing safer composite helmets to reduce rotational accelerations during oblique impacts.

PubMed

Mosleh, Yasmine; Cajka, Martin; Depreitere, Bart; Vander Sloten, Jos; Ivens, Jan

2018-05-01

Oblique impact is the most common accident situation that occupants in traffic accidents or athletes in professional sports experience. During oblique impact, the human head is subjected to a combination of linear and rotational accelerations. Rotational movement is known to be responsible for traumatic brain injuries. In this article, composite foam with a column/matrix composite configuration is proposed for head protection applications to replace single-layer uniform foam, to better attenuate rotational movement of the head during oblique impacts. The ability of composite foam in the mitigation of rotational head movement is studied by performing finite element (FE) simulations of oblique impact on flat and helmet shape specimens. The performance of composite foam with respect to parameters such as compliance of the matrix foam and the number, size and cross-sectional shape of the foam columns is explored in detail, and subsequently an optimized structure is proposed. The simulation results show that using composite foam instead of single-layer foam, the rotational acceleration and velocity of the headform can be significantly reduced. The parametric study indicates that using a more compliant matrix foam and by increasing the number of columns in the composite foam configuration, the rotation can be further mitigated. This was confirmed by experimental results. The simulation results were also analyzed based on global head injury criteria such as head injury criterion, rotational injury criterion, brain injury criterion and generalized acceleration model for brain injury threshold which further confirmed the superior performance of composite foam versus single-layer homogeneous expanded polystyrene foam. The findings of simulations give invaluable information for design of protective helmets or, for instance, headliners for the automotive industry.

Extrusion foaming of thermoplastic cellulose acetate from renewable resources using a two-component physical blowing agent system

NASA Astrophysics Data System (ADS)

Hopmann, Ch.; Windeck, C.; Hendriks, S.; Zepnik, S.; Wodke, T.

2014-05-01

Thermoplastic cellulose acetate (CA) is a bio-based polymer with optical, mechanical and thermal properties comparable to those of polystyrene (PS). The substitution of the predominant petrol-based PS in applications like foamed food trays can lead to a more sustainable economic practice. However, CA is also suitable for more durable applications as the biodegradability rate can be controlled by adjusting the degree of substitutions. The extrusion foaming of CA still has to overcome certain challenges. CA is highly hydrophilic and can suffer from hydrolytic degradation if not dried properly. Therefore, the influence of residual moisture on the melt viscosity is rather high. Beyond, the surface quality of foam CA sheets is below those of PS due to the particular foaming behaviour. This paper presents results of a recent study on extrusion foamed CA, using a two-component physical blowing agent system compromising HFO 1234ze as blowing agent and organic solvents as co-propellant. Samples with different co-propellants are processed on a laboratory single screw extruder at IKV. Morphology and surface topography are investigated with respect to the blowing agent composition and the die pressure. In addition, relationships between foam density, foam morphology and the propellants are analysed. The choice of the co-propellant has a significant influence on melt-strength, foaming behaviour and the possible blow-up ratio of the sheet. Furthermore, a positive influence of the co-propellant on the surface quality can be observed. In addition, the focus is laid on the effect of external contact cooling of the foamed sheets after the die exit.

Microminiature coaxial cable and methods manufacture

DOEpatents

Bongianni, Wayne L.

1986-01-01

A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 .mu.m thick and from 150 to 200 .mu.m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dielectric. Alternately the foam dielectric embodiment may have a contiguous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microballoons to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion.

Microminiature coaxial cable and method of manufacture

DOEpatents

Bongianni, W.L.

1989-03-28

A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 [mu]m thick and from 150 to 200 [mu]m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dielectric. Alternately, the foam dielectric embodiment may have a contiguous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microspheres to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion. 2 figs.

Microminiature coaxial cable and method of manufacture

DOEpatents

Bongianni, Wayne L.

1989-01-01

A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 .mu.m thick and from 150 to 200 .mu.m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dielectric. Alternately, the foam dielectric embodiment may have a contiguous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microspheres to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion.

Microminiature coaxial cable and methods of manufacture

DOEpatents

Bongianni, W.L.

1983-12-29

A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 ..mu..m thick and from 150 to 200 ..mu..m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dieleectric. Alternately the foam dielectric embodiment may have a contiguous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microballoons to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion.

Microminiature coaxial cable and methods manufacture

DOEpatents

Bongianni, W.L.

1986-04-08

A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 [mu]m thick and from 150 to 200 [mu]m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dielectric. Alternately the foam dielectric embodiment may have a contiguous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microballoons to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion. 2 figs.

Moisture and Thermal Conductivity of Lightweight Block Walls

NASA Astrophysics Data System (ADS)

Joosep, R.

2015-11-01

This article examines thermal properties of lightweight block walls and their changes over the course of time. Three different types of lightweight blocks and two types of heat insulation are used in construction. Aeroc aerated concrete blocks are in use, as well as compacted LECA (Lightweight Expanded Clay Aggregate) Fibo blocks made from burned clay and Silbet blocks produced from oil shale ash. Expanded Thermisol EPS60F polystyrene plates and glass wool Isover OL-P plates are used for thermal insulation. The actual and computational values of thermal conductivity and the water draining properties of walls over time are compared in this article. Water draining from glass wool walls is relatively fast. Water-draining can take over a year in polystyrene insulated walls. All four wall constructions can be used as external walls, but care must be taken regarding the moisture content of the blocks during construction (the construction should be handled with care to minimise the moisture in the blocks), especially in polystyrene board-insulated walls.

Energy-Saving Melting and Revert Reduction Technology (E-SMARRT): Lost Foam Thin Wall - Feasibility of Producing Lost Foam Castings in Aluminum and Magnesium Based Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fasoyinu, Yemi; Griffin, John A.

2014-03-31

With the increased emphasis on vehicle weight reduction, production of near-net shape components by lost foam casting will make significant inroad into the next-generation of engineering component designs. The lost foam casting process is a cost effective method for producing complex castings using an expandable polystyrene pattern and un-bonded sand. The use of un-bonded molding media in the lost foam process will impose less constraint on the solidifying casting, making hot tearing less prevalent. This is especially true in Al-Mg and Al-Cu alloy systems that are prone to hot tearing when poured in rigid molds partially due to their longmore » freezing range. Some of the unique advantages of using the lost foam casting process are closer dimensional tolerance, higher casting yield, and the elimination of sand cores and binders. Most of the aluminum alloys poured using the lost foam process are based on the Al-Si system. Very limited research work has been performed with Al-Mg and Al-Cu type alloys. With the increased emphasis on vehicle weight reduction, and given the high-strength-to-weight-ratio of magnesium, significant weight savings can be achieved by casting thin-wall (≤ 3 mm) engineering components from both aluminum- and magnesium-base alloys.« less

Ethanol-dispersed and antibody-conjugated polymer nanofibers for the selective capture and 3-dimensional culture of EpCAM-positive cells.

PubMed

Yoon, Junghyo; Yoon, Hee-Sook; Shin, Yoojin; Kim, Sanghyun; Ju, Youngjun; Kim, Jungbae; Chung, Seok

2017-07-01

Electrospun and ethanol-dispersed polystyrene-poly(styrene-co-maleic anhydride) (PS-PSMA) nanofibers (NFs) were used as a platform for the selective capture and three-dimensional culture of EpCAM-positive cells in cell culture medium and whole blood. The NFs were treated with streptavidin to facilitate bond formation between the amino groups of streptavidin and the maleic anhydride groups of the NFs. A biotinylated anti-EpCAM monoclonal antibody (mAb) was attached to the streptavidin-conjugated NFs via the selective binding of streptavidin and biotin. Upon simple mixing and shaking with EpCAM-positive cancer cells in a wide concentration range from 10 to 1000,000 cells per 10mL, the mAb-attached NFs (mAb-NFs) captured the Ep-CAM positive cells in an efficiency of 59%-67% depending on initial cell concentrations, with minor mechanical capture of 14%-36%. Captured cells were directly cultured, forming cell aggregates, in the NF matrix, which ensures the cell proliferation and follow-up analysis. Furthermore, the capture capacity of mAb-NFs was assessed in the presence of whole blood and blood lysates, indicating cluster formation that captured target cells. It is anticipated that the antibody-attached NFs can be employed for the capture and analysis of very rare EpCAM positive circulating cancer cells. Copyright © 2017 Elsevier Inc. All rights reserved.

DOE Zero Energy Ready Home Case Study: Healthy Efficient Homes - Spirit Lake, Iowa

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2014-11-01

This case study describes a DOE Zero Energy Ready Home in Spirit Lake, Iowa, that scored HERS 41 without PV and HERS 28 with PV. This 3,048 ft2 custom home has advanced framed walls filled with 1.5 inches closed-cell spray foam, a vented attic with spray foam-sealed top plates and blown fiberglass over the ceiling deck. R-23 basement walls are ICF plus two 2-inch layers of EPS. The house also has a mini-split heat pump, fresh air fan intake, and a solar hot water heater.

Selected engineering properties and applications of EPS geofoam

NASA Astrophysics Data System (ADS)

Elragi, Ahmed Fouad

Expanded polystyrene (EPS) geofoam is a lightweight material that has been used in engineering applications since at least the 1950s. Its density is about a hundredth of that of soil. It has good thermal insulation properties with stiffness and compression strength comparable to medium clay. It is utilized in reducing settlement below embankments, sound and vibration damping, reducing lateral pressure on substructures, reducing stresses on rigid buried conduits and related applications. This study starts with an overview on EPS geofoam. EPS manufacturing processes are described followed by a review of engineering properties found in previous research work done so far. Standards and design manuals applicable to EPS are presented. Selected EPS geofoam-engineering applications are discussed with examples. State-of-the-art of experimental work is done on different sizes of EPS specimens under different loading rates for better understanding of the behavior of the material. The effects of creep, sample size, strain rate and cyclic loading on the stress strain response are studied. Equations for the initial modulus and the strength of the material under compression for different strain rates are presented. The initial modulus and Poisson's ratio are discussed in detail. Sample size effect on creep behavior is examined. Three EPS projects are shown in this study. The creep behavior of the largest EPS geofoam embankment fill is shown. Results from laboratory tests, mathematical modeling and field records are compared to each other. Field records of a geofoam-stabilized slope are compared to finite difference analysis results. Lateral stress reduction on an EPS backfill retaining structure is analyzed. The study ends with a discussion on two promising properties of EPS geofoam. These are the damping ability and the compressibility of this material. Finite element analysis, finite difference analysis and lab results are included in this discussion. The discussion with the rest of the study points towards the main conclusion that EPS geofoam is the future material of promise in various civil engineering applications.

EGFR-Based Immunoisolation as a Recovery Target for Low-EpCAM CTC Subpopulation

PubMed Central

Vila, Ana; Abal, Miguel; Muinelo-Romay, Laura; Rodriguez-Abreu, Carlos; Rivas, José; López-López, Rafael; Costa, Clotilde

2016-01-01

Circulating tumour cells (CTCs) play a key role in the metastasis process, as they are responsible for micrometastasis and are a valuable tool for monitoring patients in real-time. Moreover, efforts to develop new strategies for CTCs isolation and characterisation, and the translation of CTCs into clinical practice needs to overcome the limitation associated with the sole use of Epithelial Cell Adhesion Molecule (EpCAM) expression to purify this tumour cell subpopulation. CTCs are rare events in the blood of patients and are believed to represent the epithelial population from a primary tumour of epithelial origin, thus EpCAM immunoisolation is considered an appropriate strategy. The controversy stems from the impact that the more aggressive mesenchymal tumour phenotypes might have on the whole CTC population. In this work, we first characterised a panel of cell lines representative of tumour heterogeneity, confirming the existence of tumour cell subpopulations with restricted epithelial features and supporting the limitations of EpCAM-based technologies. We next developed customised polystyrene magnetic beads coated with antibodies to efficiently isolate the phenotypically different subpopulations of CTCs from the peripheral blood mononuclear cells (PBMCs) of patients with metastatic cancer. Besides EpCAM, we propose Epidermal Growth Factor Receptor (EGFR) as an additional isolation marker for efficient CTCs detection. PMID:27711186

Measure Guideline: Installing Rigid Foam Insulation on the Interior of Existing Brick Walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Natarajan, H.; Klocke, S.; Puttagunta, S.

2012-06-01

This measure guideline provides information on an effective method to insulate the interior of existing brick masonry walls with extruded polystyrene (XPS) insulation board. The guide outlines step-by-step design and installation procedures while explaining the benefits and tradeoffs where applicable. The authors intend that this document be useful to a varied audience that includes builders, remodelers, contractors and homeowners.

Measure Guideline. Installing Rigid Foam Insulation on the Interior of Existing Brick Walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Natarajan, Hariharan; Klocke, Steve; Puttagunta, Srikanth

2012-06-01

This measure guideline provides information on an effective method to insulate the interior of existing brick masonry walls with extruded polystyrene (XPS) insulation board. The guide outlines step-by-step design and installation procedures while explaining the benefits and tradeoffs where applicable. The authors intend that this document be useful to a varied audience that includes builders,remodelers, contractors and homeowners.

U.S. Navy Shipboard-Generated Plastic Waste Pilot Recycling Program

DTIC Science & Technology

1991-03-01

2: Recyclable Plastic Items Collected from Lexington Waste at Escambia County MRF Shampoo containers Plastic garbage bags Tyvek suit Shower thongs...bale consisted of polystyrene foam cups, bread bags, bottles, disposable razors, latex gloves, shampoo bottles, and othermiscellaneous items listed in...recent csws telephone survey of recycling firms involved in the separation of mixed 46 plastic bottles, the cost of sorting plastic bottles is

Preparation and characterization of starch-based loose-fill packaging foams

NASA Astrophysics Data System (ADS)

Fang, Qi

Regular and waxy corn starches were blended in various ratios with biodegradable polymers including polylactic acid (PLA), Eastar Bio Copolyester 14766 (EBC) and Mater-Bi ZF03U (MBI) and extruded with a C. W. Brabender laboratory twin screw extruder using a 3-mm die nozzle at 150°C and 150 rev/min. Physical characteristics including radial expansion, unit density and bulk density and water solubility index, water absorption characteristics, mechanical properties including compressibility, Young's modulus, spring index, bulk compressibility and bulk spring index and abrasion resistance were investigated as affected by the ingredient formulations, i.e. type of polymers, type of starches, polymer to starch ratio and starch moisture content. A completely randomized factorial blocking experimental design was used. Fifty-four treatments resulted. Each treatment was replicated three times. SAS statistical software package was used to analyze the data. Foams made of waxy starch had better radial expansion, lower unit density and bulk density than did foams made of regular starch. Regular starch foams had significantly lower water solubility index than did the waxy starch foams. PLA-starch foams had the lowest compressibility and Young's modulus. MBI-starch foams were the most rigid. All foams had excellent spring indices and bulk spring indices which were comparable to the spring index of commercial expanded polystyrene foam. Correlations were established between the foam mechanical properties and the physical characteristics. Foam compressibility and Young's modulus decreased as increases in radial expansion and decreases in unit and bulk densities. Their relationships were modeled with power law equations. No correlation was observed between spring index and bulk spring index and foam physical characteristics. MBI-starch foams had the highest equilibrium moisture content. EBC-starch and PLA-starch foams had similar water absorption characteristics. No significant difference existed in water absorption characteristics between foams made of regular and waxy starches. Empirical models were developed to correlate foam water absorption characteristics with relative humidity and polymer content. The developed models fit the data well with relatively small standard errors and uniformly scattered residual plots. Foams with higher polymer content had better abrasion resistance than did foams with lower polymer content.

Preparation and Properties of C/C Hollow Spheres and the Energy Absorption Capacity of the Corresponding Aluminum Syntactic Foams.

PubMed

Yu, Qiyong; Zhao, Yan; Dong, Anqi; Li, Ye

2018-06-12

The present study focuses on the preparation and characterization of lab-scale aluminum syntactic foams (ASFs) filled with hollow carbon spheres (HCSs). A new and original process for the fabrication of HCSs was explored. Firstly, expanded polystyrene beads with an average diameter of 6 mm and coated with carbon fibers/thermoset phenolic resin were produced by the “rolling ball” method. In the next step, the spheres were cured and post-cured, and then carbonized at 1050 °C under vacuum to form the HCSs. The porosity in the shell of the HCSs was decreased by increasing the number of impregnation⁻carbonization cycles. The aluminum syntactic foams were fabricated by casting the molten aluminum into a crucible filled with HCSs. The morphology of the hollow spheres before and after carbonization was investigated by scanning electron microscope (SEM). The compressive properties of the ASF were tested and the energy absorption capacities were calculated according to stress⁻strain curves. The results showed that the ASF filled with HCSs which had been treated by more cycles of impregnation⁻carbonization had higher energy absorption capacity. The aluminum syntactic foam absorbed 34.9 MJ/m³ (28.8 KJ/Kg) at 60% strain, which was much higher than traditional closed cell aluminum foams without particles. The HCSs have a promising future in producing a novel family of metal matrix syntactic foams.

Improved construction materials for polar regions using microcellular thermoplastic foams

NASA Technical Reports Server (NTRS)

Cunningham, Daniel J.

1994-01-01

Microcellular polymer foams (MCF) are thermoplastic foams with very small cell diameters, less than 10 microns, and very large cell densities, 10(exp 9) to 10(exp 15) cells per cubic centimeter of unfoamed material. The concept of foaming polymers with microcellular voids was conceived to reduce the amount of material used for mass-produced items without compromising the mechanical properties. The reasoning behind this concept was that if voids smaller than the critical flaw size pre-existing in polymers were introduced into the matrix, they would not affect the overall strength of the product. MCF polycarbonate (PC), polystyrene (PS), and polyvinyl chloride (PVC) were examined to determine the effects of the microstructure towards the mechanical properties of the materials at room and arctic temperatures. Batch process parameters were discovered for these materials and foamed samples of three densities were produced for each material. To quantify the toughness and strength of these polymers, the tensile yield strength, tensile toughness, and impact resistance were measured at room and arctic temperatures. The feasibility of MCF polymers has been demonstrated by the consistent and repeatable MCF microstructures formed, but the improvements in the mechanical properties were not conclusive. Therefore the usefulness of the MCF polymers to replace other materials in arctic environments is questionable.

Absolute Hugoniot measurements for CH foams in the 1.5-8 Mbar range

NASA Astrophysics Data System (ADS)

Aglitskiy, Y.; Velikovich, A. L.; Schmitt, A. J.; Karasik, M.; Serlin, V.; Weaver, J. L.; Oh, J.; Obenschain, S. P.

2016-10-01

We report the absolute Hugoniot measurements for dry CH foams at 10% of solid polystyrene density. The 400 μm thick, 500 μm wide planar foam slabs covered with a 10 μm solid plastic ablator were driven with 4 ns long Nike KrF laser pulses whose intensity was varied between 10 and 50 TW/cm2. The trajectories of the shock front and the ablative piston, as well as the rarefaction fan emerging after the shock breakout from the rear surface of the target were clearly observed using the side-on monochromatic x-ray imaging radiography. From these measurements the shock density compression ratio and the shock pressure are evaluated directly. The observed compression ratios varied between 4 and 8, and the corresponding shock pressures - between 1.5 and 8 Mbar. The data was simulated with the FASTRAD3D hydrocode, using standard models of inverse bremsstrahlung absorption, flux-limited thermal conduction, and multi-group radiation diffusion. The demonstrated diagnostics technique applied in a cryo experiment would make it possible to make the first absolute Hugoniot measurements for liquid deuterium or DT-wetted CH foams, which is relevant for designing the wetted-foam indirect-drive ignition targets for NIF. This work was supported by the US DOE/NNSA.

Facile synthesis of porous graphene as binder-free electrode for supercapacitor application

NASA Astrophysics Data System (ADS)

Luo, Guangsheng; Huang, Haifu; Lei, Chenglong; Cheng, Zhenzhi; Wu, Xiaoshan; Tang, Shaolong; Du, Youwei

2016-03-01

Here, porous grapheme oxide (GO) gel deposited on nickel foam was prepared by using polystyrene (PS) colloidal particles as spacers for use as electrodes in high rate supercapacitors, then reduced by Vitamin C aqueous solution in ambient condition. The PS particles were surrounded by reduced graphene oxide (rGO) sheets, forming crinkles and rough textures. When PS particles were selectively removed, rGO gel coated on the skeleton of Ni foam can formed an open porous structure, which prevents elf-aggregation and restacking of graphene sheets. The porous rGO-based supercapacitors exhibit excellent electrochemical performances such as a specific capacitance of 152 F g-1 at 1 A g-1, high rate capability of 53% capacitance retention upon a current increase to 100 A g-1 and good cycle stability, due to effective rapid and short pathways for ionic and electronic transport provided by the sub-micrometer structure of rGO gel and 3D interconnected network of Ni foam.

Elemental concentrations and bioaccessibilities in beached plastic foam litter, with particular reference to lead in polyurethane.

PubMed

Turner, Andrew; Lau, Kwan S

2016-11-15

Seventy samples of foamed plastic collected from a high-energy, sandy beach in SW England have been characterised by FTIR and XRF. Most samples were polyurethane (PU; n=39) or polystyrene (PS; n=27) that were associated with variable concentrations of Br-Cl, Fe and Zn, indicative of the presence of halogenated flame retardants, iron oxides and Zn-based additives, respectively. Many samples of rigid PU contained Pb, historically used as a catalyst, at concentrations of up to 16,000μgg -1 . A physiological extraction test that simulates the conditions in the gizzard of plastic-ingesting seabirds was applied to selected samples and results revealed that while Br and Zn were not measurably bioaccessible, Pb mobilisation progressed logarithmically over a period of time with maximum accessibilities after 220h of ~10% of total metal. Foamed PU is a source of bioaccessible Pb in the marine environment that has not previously been documented. Copyright © 2016 Elsevier Ltd. All rights reserved.

Sorption of organic compounds by aged polystyrene microplastic particles.

PubMed

Hüffer, Thorsten; Weniger, Anne-Katrin; Hofmann, Thilo

2018-05-01

Microplastics that are released into the environment undergo aging and interact with other substances such as organic contaminants. Understanding the sorption interactions between aged microplastics and organic contaminants is therefore essential for evaluating the impact of microplastics on the environment. There is little information available on how the aging of microplastics affects their sorption behavior and other properties. We have therefore investigated the effects of an accelerated UV-aging procedure on polystyrene microplastics, which are used in products such as skin cleaners and foams. Physical and chemical particle characterizations showed that aging led to significant surface oxidation and minor localized microcrack formation. Sorption coefficients of organic compounds by polystyrene microplastics following aging were up to one order of magnitude lower than for pristine particles. Sorption isotherms were experimentally determined using a diverse set of probe sorbates covering a variety of substance classes allowing an in-depth evaluation of the poly-parameter linear free-energy relationship (ppLFER) modelling used to investigate the contribution of individual molecular interactions to overall sorption. The ppLFER modelling was validated using internal cross-validation, which confirmed its robustness. This approach therefore yields improved estimates of the interactions between aged polystyrene microplastics and organic contaminants. Copyright © 2018 Elsevier Ltd. All rights reserved.

Absolute Hugoniot measurements for CH foams in the 2–9 Mbar range

DOE PAGES

Aglitskiy, Y.; Velikovich, A. L.; Karasik, M.; ...

2018-03-19

Absolute Hugoniot measurements for empty plastic foams at ~10% of solid polystyrene density and supporting rad-hydro simulation results are reported. Planar foam slabs, ~400 μm thick and ~500 μm wide, some of which were covered with a 10 μm solid plastic ablator, were directly driven by 4 ns long Nike krypton-fluoride 248 nm wavelength laser pulses that produced strong shock waves in the foam. The shock and mass velocities in our experiments were up to 104 km/s and 84 km/s, respectively, and the shock pressures up to ~9 Mbar. The motion of the shock and ablation fronts was recorded usingmore » side-on monochromatic x-ray imaging radiography. Here, the steadiness of the observed shock and ablation fronts within ~1% has been verified. The Hugoniot data inferred from our velocity measurements agree with the predictions of the SESAME and CALEOS equation-of-state models near the highest pressure ~9 Mbar and density compression ratio ~5. In the lower pressure range 2–5 Mbar, a lower shock density compression is observed than that predicted by the models. Possible causes for this discrepancy are discussed.« less

Absolute Hugoniot measurements for CH foams in the 2-9 Mbar range

NASA Astrophysics Data System (ADS)

Aglitskiy, Y.; Velikovich, A. L.; Karasik, M.; Schmitt, A. J.; Serlin, V.; Weaver, J. L.; Oh, J.; Obenschain, S. P.; Cochrane, K. R.

2018-03-01

Absolute Hugoniot measurements for empty plastic foams at ˜10% of solid polystyrene density and supporting rad-hydro simulation results are reported. Planar foam slabs, ˜400 μm thick and ˜500 μm wide, some of which were covered with a 10 μm solid plastic ablator, were directly driven by 4 ns long Nike krypton-fluoride 248 nm wavelength laser pulses that produced strong shock waves in the foam. The shock and mass velocities in our experiments were up to 104 km/s and 84 km/s, respectively, and the shock pressures up to ˜9 Mbar. The motion of the shock and ablation fronts was recorded using side-on monochromatic x-ray imaging radiography. The steadiness of the observed shock and ablation fronts within ˜1% has been verified. The Hugoniot data inferred from our velocity measurements agree with the predictions of the SESAME and CALEOS equation-of-state models near the highest pressure ˜9 Mbar and density compression ratio ˜5. In the lower pressure range 2-5 Mbar, a lower shock density compression is observed than that predicted by the models. Possible causes for this discrepancy are discussed.

Investigation of fluorocarbon blowing agents in insulating polymer foams by 19F NMR imaging.

PubMed

Fyfe, C A; Mei, Z; Grondey, H

1996-01-01

Currently, there is no reliable and readily accessible technique with which the distribution and diffusion of blowing agents in rigid insulating foams can be detected and monitored. In this paper, we demonstrate that 19F NMR microscopic imaging together with 19F solid-state MAS NMR spectroscopy is ideally suited for such measurements and yield quantitatively reliable information that will be critical to the development and fabrication of optimized insulating materials with alternative blowing agents. Polystyrene (PS) and polyurethane (PU) foam samples were investigated with the objective of determining quantitatively the amount of blowing agents in the gaseous phase and dissolved in the polymer phase, and to determine and monitor the distribution of the blowing agents in aged foams as a function of time and temperature. The concentrations of the gaseous blowing agents in the cells and dissolved in the solid were simultaneously and quantitatively measured by 19F MAS NMR spectroscopy. An unfaced 1-yr-old PS foam filled with CH3CF2Cl has about 13% of total HCFCs dissolved in the solid; while there is about 24% of HCFCs in the solid of a faced 3-mos-old PU foam filled with CH3CCl2F. The data from 19F NMR imaging demonstrate that the distributions of the blowing agents in an aged foam are quite uniform around the center part (2 cm away from any edge) of a foam board; however, a gradient in blowing agent concentration was found as a function of distance from the initial factory cut edge. The effective diffusion coefficients of the blowing agents can be directly calculated from the imaging data. Quantitative diffusion constants and activation barriers were determined. Additionally, a foam treated with a second blowing agent was monitored with chemical shift selective imaging and the diffusion of the second gas into the foam and the out-diffusion of the original gas were determined.

Life cycle assessment of EPS and CPB inserts: design considerations and end of life scenarios.

PubMed

Tan, Reginald B H; Khoo, Hsien H

2005-02-01

Expanded polystyrene (EPS) and corrugated paperboard (CPB) are used in many industrial applications, such as containers, shock absorbers or simply as inserts. Both materials pose two different types of environmental problems. The first is the pollution and resource consumption that occur during the production of these materials; the second is the growing landfills that arise out of the excessive disposal of these packaging materials. Life cycle assessment or LCA will be introduced in this paper as a useful tool to compare the environmental performance of both EPS and CPB throughout their life cycle stages. This paper is divided into two main parts. The first part investigates the environmental impacts of the production of EPS and CPB from 'cradle-to-gate', comparing two inserts--both the original and proposed new designs. In the second part, LCA is applied to investigate various end-of-life cases for the same materials. The study will evaluate the environmental impacts of the present waste management practices in Singapore. Several 'what-if' cases are also discussed, including various percentages of landfilling and incineration. The SimaPro LCA Version 5.0 software's Eco-indicator 99 method is used to investigate the following five environmental impact categories: climate change, acidification/eutrophication, ecotoxicity, fossil fuels and respiratory inorganics.

Biodegradable Poly (Ester Urethane) Urea Biomaterials For Applications in Combat Casualty Care

DTIC Science & Technology

2006-11-01

hydroxyapatite (Irvine, CA), and tissue culture polystyrene were used as positive controls in the cell culture experiments. 3.2 Synthesis of PEUUR cast...was performed to detect biomineralization after 28 days of culture in osteogenic medium. 3.6 MicroFT- IR The composition of the materials and...biomineralization was assessed by micro FT- IR (Nicollet Coninuµm™). After 28 days of cell culture on the foams the sample with the cells was fixed

Behavior of Materials at Cold Regions Temperatures. Part 1. Program Rationale and Test Plan

DTIC Science & Technology

1988-07-01

10 15 i" 0% I 0 0 0 2 3 4 5a 0 1 2 3 4 5 6 7 lf CSTRAIN (IN/INbST AI OW N V, Figure B47. Static stress vs strain curves for resilient expanded ... polystyrene foam (Resilo-Pak) , at temperature extremes (0.5, 0. 75 and 1.3 lb Ifft3 densities) (Titus 1967). so ,eSF 50 -- 8 * TEMPERATURE. K 0 so 100 is

Laboratory simulation of intact capture of cometary and asteroidal dust particles in ISAS

NASA Technical Reports Server (NTRS)

Fujiwara, A.; Nakamura, A.; Kadono, T.

1994-01-01

In order to develop a collector for intact capturing of cometary dust particles in the SOCCER mission and regolith dust particles released from asteroid surfaces by the impact of projectiles launched from a flying-by spacecraft, various kinds of materials as the collector candidates have been exposed to hypervelocity projectiles in our laboratory. Data based on the penetration characteristics of various materials (penetration depth, hole profile, effectiveness for intact capturing) are greatly increased. The materials tested for these simulation experiments include various kinds of low-density media and multisheet stacks; these are foamed plastics (polystyrene 0.01 g/cc), silica aerogels (0.04 g/cc), air (0.001 g/cc), liquid, and multisheet stack consisting of thin Al sheets (thickness 0.002 to 0.1 mm) or polyethylene sheets. Projectiles used are spheres or cylinders of nylon, polycarbonate, basalt, copper, iron, and volatile organics (e.g.,paradichlorobenzene) of size ranging from 30 micrometers to 1 cm launched by a two-stage light gas gun and a rail gun in ISAS at velocity up to about 7 km/s. Some results obtained by using nylon projectiles of velocity less than about 5 km/s are presented; the penetration depth vs. bulk density of the collector material for several kinds of materials and the velocity at which the projectiles begin to fragment vs. material density for foamed polystyrene.

Extracellular polymer substance synthesized by a halophilic bacterium Chromohalobacter canadensis 28.

PubMed

Radchenkova, Nadja; Boyadzhieva, Ivanka; Atanasova, Nikolina; Poli, Annarita; Finore, Ilaria; Di Donato, Paola; Nicolaus, Barbara; Panchev, Ivan; Kuncheva, Margarita; Kambourova, Margarita

2018-04-03

Halophilic microorganisms are producers of a lot of new compounds whose properties suggest promising perspectives for their biotechnological exploration. Moderate halophilic bacterium Chromohalobacter canadensis 28 was isolated from Pomorie salterns as an extracellular polymer substance (EP) producer. The best carbon source for extracellular polymer production was found to be lactose, a sugar received as a by-product from the dairy industry. After optimization of the culture medium and physicochemical conditions for cultivation, polymer biosynthesis increased more than 2-fold. The highest level of extracellular polymer synthesis by C. canadensis 28 was observed in an unusually high NaCl concentration (15% w/v). Chemical analysis of the purified polymer revealed the presence of an exopolysaccharide (EPS) fraction (14.3% w/w) and protein fraction (72% w/w). HPLC analysis of the protein fraction showed the main presence of polyglutamic acid (PGA) (75.7% w/w). EPS fraction analysis revealed the following sugar composition (% w/w): glucosamine 36.7, glucose 32.3, rhamnose 25.4, xylose 1.7, and not identified sugar 3.9. The hydrogel formed by PGA and EPS fractions showed high swelling behavior, very good emulsifying and stabilizing properties, and good foaming ability. This is the first report for halophilic bacterium able to synthesize a polymer containing PGA fraction. The synthesized biopolymer shows an extremely high hydrophilicity, due to the simultaneous presence of PGA and EPS. The analysis of its functional properties and the presence of glucosamine in the highest proportion in EPS fraction clearly determine the potential of EP synthesized by C. canadensis 28 for application in the cosmetics industry.

An experimental-finite element analysis on the kinetic energy absorption capacity of polyvinyl alcohol sponge.

PubMed

Karimi, Alireza; Navidbakhsh, Mahdi; Razaghi, Reza

2014-06-01

Polyvinyl alcohol (PVA) sponge is in widespread use for biomedical and tissue engineering applications owing to its biocompatibility, availability, relative cheapness, and excellent mechanical properties. This study reports a novel concept of design in energy absorbing materials which consist in the use of PVA sponge as an alternative reinforcement material to enhance the energy loss of impact loads. An experimental study is carried out to measure the mechanical properties of the PVA sponge under uniaxial loading. The kinetic energy absorption capacity of the PVA sponge is computed by a hexahedral finite element (FE) model of the steel ball and bullet through the LS-DYNA code under impact load at three different thicknesses (5, 10, 15mm). The results show that a higher sponge thickness invokes a higher energy loss of the steel ball and bullet. The highest energy loss of the steel ball and bullet is observed for the thickest sponge with 160 and 35J, respectively. The most common type of traumatic brain injury in which the head subject to impact load causes the brain to move within the skull and consequently brain hemorrhaging. These results suggest the application of the PVA sponge as a great kinetic energy absorber material compared to commonly used expanded polystyrene foams (EPS) to absorb most of the impact energy and reduces the transmitted load. The results might have implications not only for understanding of the mechanical properties of PVA sponge but also for use as an alternative reinforcement material in helmet and packaging material design. Copyright © 2014 Elsevier B.V. All rights reserved.

Persistent organic pollutants in plastic marine debris found on beaches in San Diego, California.

PubMed

Van, Almira; Rochman, Chelsea M; Flores, Elisa M; Hill, Kish L; Vargas, Erica; Vargas, Serena A; Hoh, Euhna

2012-01-01

Plastic debris were collected from eight beaches around San Diego County, California. Debris collected include: pre-production pellets and post-consumer plastics including fragments, polystyrene (PS) foam, and rubber. A total of n = 2453 pieces were collected ranging from <5 mm to 50 mm in size. The plastic pieces were separated by type, location, and appearance and analyzed for polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), dichlorodiphenyltrichloroethane (DDT) and its breakdown products, and chlordanes. PAH concentrations ranged from 30 ng g(-1) to 1900 ng g(-1), PCBs from non-detect to 47 ng g(-1), chlordanes from 1.8 ng g(-1) to 60 ng g(-1), and DDTs from non-detect to 76 ng g(-1). Consistently higher PAH concentrations found in PS foam samples (300-1900 ng g(-1)) led us to examine unexposed PS foam packaging materials and PS virgin pellets. Unexposed PS foam contained higher concentrations of PAHs (240-1700 ng g(-1)) than PS virgin pellets (12-15 ng g(-1)), suggesting that PAHs may be produced during manufacturing. Temporal trends of debris were investigated at one site, Ocean Beach, where storm events and beach maintenance were found to be important variables influencing debris present at a given time. Copyright © 2011 Elsevier Ltd. All rights reserved.

Using Sodium Hydrogen Carbonate for Foaming Polymers

NASA Astrophysics Data System (ADS)

Satin, Lukáš; Likavčan, Lukáš; Košík, Miroslav; Rantuch, Peter; Bílik, Jozef

2016-09-01

All plastics products are made of the essential polymer mixed with a complex blend of materials known collectively as additives. Without additives, plastics would not work, but with them, they can be made safer, cleaner, tougher and more colourful. Additives cost money, but by reducing production costs and making products live longer, they help us save money and conserve the world's precious raw material reserves. In fact, our world would be a lot less safe, a lot more expensive and a great deal duller without the additives that turn basic polymers into useful plastics. One of these additives is sodium bicarbonate. Influence of sodium bicarbonate on properties of the product made of polystyrene was observed in the research described in this paper. Since polystyrene is typically used as a material for electrical components, the mechanical properties of tensile strength and inflammability were measured as a priority. Inflammability parameters were measured using a cone calorimeter.

75 FR 6795 - Designation of Biobased Items for Federal Procurement

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-10

...The U.S. Department of Agriculture (USDA) is proposing to amend the Guidelines for Designating Biobased Products for Federal Procurement (Guidelines) to add nine sections that will designate the following items within which biobased products would be afforded Federal procurement preference: Disposable tableware; expanded polystyrene foam recycling products; heat transfer fluids; ink removers and cleaners; mulch and compost materials; multipurpose lubricants; office paper; topical pain relief products; and turbine drip oils. USDA is also proposing minimum biobased contents for each of these items.

Hong Kong at the Pearl River Estuary: A hotspot of microplastic pollution.

PubMed

Fok, Lincoln; Cheung, P K

2015-10-15

Large plastic (>5mm) and microplastic (0.315-5mm) debris were collected from 25 beaches along the Hong Kong coastline. More than 90% consisted of microplastics. Among the three groups of microplastic debris, expanded polystyrene (EPS) represented 92%, fragments represented 5%, and pellets represented 3%. The mean microplastic abundance for Hong Kong was 5595items/m(2). This number is higher than international averages, indicating that Hong Kong is a hotspot of marine plastic pollution. Microplastic abundance was significantly higher on the west coast than on the east coast, indicating that the Pearl River, which is west of Hong Kong, may be a potential source of plastic debris. The amounts of large plastic and microplastic debris of the same types (EPS and fragments) were positively correlated, suggesting that the fragmentation of large plastic material may increase the quantity of beach microplastic debris. Copyright © 2015 Elsevier Ltd. All rights reserved.

Fast and selective cell isolation from blood sample by microfiber fabric system with vacuum aspiration

NASA Astrophysics Data System (ADS)

Ueki, Takayuki; Yoshihara, Akifumi; Teramura, Yuji; Takai, Madoka

2016-01-01

Since circulating tumor cells (CTCs) are tumor cells which are found in the blood of cancer patients, CTCs are potential tumor markers, so a rapid isolation of CTCs is desirable for clinical applications. In this paper, a three-dimensional polystyrene (PS) microfiber fabric with vacuum aspiration system was developed for capturing CTCs within a short time. Various microfiber fabrics with different diameters were prepared by the electrospinning method and optimized for contact frequency with cells. Vacuum aspiration utilizing these microfiber fabrics could filter all cells within seconds without mechanical damage. The microfiber fabric with immobilized anti-EpCAM antibodies was able to specifically capture MCF-7 cells that express EpCAM on their surfaces. The specificity of the system was confirmed by monitoring the ability to isolate MCF-7 cells from a mixture containing CCRF-CEM cells that do not express EpCAM. Furthermore, the selective capture ability of the microfiber was retained even when the microfiber was exposed to the whole blood of pigs spiked with MCF-7 cells. The specific cell capture ratio of the vacuum aspiration system utilizing microfiber fabric could be improved by increasing the thickness of the microfiber fabric through electrospinning time.

Process Development and Micro-Machining of MARBLE Foam-Cored Rexolite Hemi-Shell Ablator Capsules

DOE PAGES

Randolph, Randall Blaine; Oertel, John A.; Schmidt, Derek William; ...

2016-06-30

For this study, machined CH hemi-shell ablator capsules have been successfully produced by the MST-7 Target Fabrication Team at Los Alamos National Laboratory. Process development and micro-machining techniques have been developed to produce capsules for both the Omega and National Ignition Facility (NIF) campaigns. These capsules are gas filled up to 10 atm and consist of a machined plastic hemi-shell outer layer that accommodates various specially engineered low-density polystyrene foam cores. Machining and assembly of the two-part, step-jointed plastic hemi-shell outer layer required development of new techniques, processes, and tooling while still meeting very aggressive shot schedules for both campaigns.more » Finally, problems encountered and process improvements will be discussed that describe this very unique, complex capsule design approach through the first Omega proof-of-concept version to the larger NIF version.« less

Proton probing of a relativistic laser interaction with near-critical plasma

NASA Astrophysics Data System (ADS)

Willingale, Louise; Zulick, C.; Thomas, A. G. R.; Maksimchuk, A.; Krushelnick, K.; Nilson, P. M.; Stoeckl, C.; Sangster, T. C.; Nazarov, W.

2014-10-01

The Omega EP laser (1000 J in 10 ps pulses) was used to investigate a relativistic intensity laser interaction with near-critical density plasma using a transverse proton beam to diagnose the large electromagnetic fields generated. A very low density foam target mounted in a washer provided the near-critical density conditions. The fields from a scaled, two-dimensional particle-in-cell simulation were inputed into a particle-tracking code to create simulated proton probe images. This allows us to understand the origins of the complex features in the experimental images, including a rapidly expanding sheath field, evidence for ponderomotive channeling and fields at the foam-washer interface. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0002028.

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

Case study of a DOE 2015 Housing Innovation Award winning production home in the mixed-dry climate that got a HERS 44 without PV, or HERS -2 with PV, with 2x4 walls 16” on center walls with R-15 cavity plus 1” EPS exterior rigid foam, slab on grade with R-10 slab edge; unvented attic with R-38 blown fiberglass netted to underside of roof deck; 19 SEER heat pump; heat pump water heater; 100% LED.

Brominated Flame Retardants, Tetrabromobisphenol A and Hexabromocyclododecane, Activate Mitogen-Activated Protein Kinases (MAPKs) in Human Natural Killer Cells

PubMed Central

Cato, Anita; Celada, Lindsay; Kibakaya, Esther Caroline; Simmons, Nadia; Whalen, Margaret M.

2014-01-01

NK cells provide a vital surveillance against virally infected cells, tumor cells, and antibody-coated cells through the release of cytolytic mediators and gamma interferon (IFN-γ). Hexabromocyclododecane (HBCD) is a brominated flame retardant used primarily in expanded (EPS) and extruded (XPS) polystyrene foams for thermal insulation in the building and construction industry. Tetrabromobisphenol A (TBBPA) is used both as a reactive and an additive flame retardant in a variety of materials. HBCD and TBBPA contaminate the environment and are found in human blood samples. In previous studies, we have shown that other environmental contaminants, such as the dibutyltin (DBT) and tributyltin (TBT), decrease NK lytic function by activating mitogen-activated protein kinases (MAPKs) in the NK cells. HBCD and TBBPA also interfere with NK cell(s) lytic function. The current study evaluates whether HBCD and/or TBBPA have the capacity to activate MAPKs and MAPK kinases (MAP2Ks). The effects of concentrations of HBCD and TBBPA that inhibited lytic function on the phosphorylation state and total levels of the MAPKs (p44/42, p38, and JNK) and the phosphorylation and total levels of the MAP2Ks (MEK1/2 and MKK3/6) were examined. Results indicate that exposure of human NK cells to 10-0.5 µM HBCD or TBBPA activate MAPKs and MAP2Ks. This HBCD and TBBPA-induced activation of MAPKs may leave them unavailable for activation by virally infected or tumor target cells and thus contributes to the observed decreases in lytic function seen in NK cells exposed to HBCD and TBBPA. PMID:25341744

Brominated flame retardants, tetrabromobisphenol A and hexabromocyclododecane, activate mitogen-activated protein kinases (MAPKs) in human natural killer cells.

PubMed

Cato, Anita; Celada, Lindsay; Kibakaya, Esther Caroline; Simmons, Nadia; Whalen, Margaret M

2014-12-01

Natural killer (NK) cells provide a vital surveillance against virally infected cells, tumor cells, and antibody-coated cells through the release of cytolytic mediators and gamma interferon (IFN-γ). Hexabromocyclododecane (HBCD) is a brominated flame retardant used primarily in expanded (EPS) and extruded (XPS) polystyrene foams for thermal insulation in the building and construction industry. Tetrabromobisphenol A (TBBPA) is used both as a reactive and an additive flame retardant in a variety of materials. HBCD and TBBPA contaminate the environment and are found in human blood samples. In previous studies, we have shown that other environmental contaminants, such as the dibutyltin (DBT) and tributyltin (TBT), decrease NK lytic function by activating mitogen-activated protein kinases (MAPKs) in the NK cells. HBCD and TBBPA also interfere with NK cell(s) lytic function. The current study evaluates whether HBCD and/or TBBPA have the capacity to activate MAPKs and MAPK kinases (MAP2Ks). The effects of concentrations of HBCD and TBBPA that inhibited lytic function on the phosphorylation state and total levels of the MAPKs (p44/42, p38, and JNK) and the phosphorylation and total levels of the MAP2Ks (MEK1/2 and MKK3/6) were examined. Results indicate that exposure of human NK cells to 10-0.5 μM HBCD or TBBPA activate MAPKs and MAP2Ks. This HBCD and TBBPA-induced activation of MAPKs may leave them unavailable for activation by virally infected or tumor target cells and thus contributes to the observed decreases in lytic function seen in NK cells exposed to HBCD and TBBPA.

Application of water flowing PVC pipe and EPS foam bead as insulation for wall panel

NASA Astrophysics Data System (ADS)

Ali, Umi Nadiah; Nor, Norazman Mohamad; Yusuf, Mohammed Alias; Othman, Maidiana; Yahya, Muhamad Azani

2018-02-01

Malaysia located in tropical climate which have a typical temperature range between 21 °C to 36 °C. Due to this, air-conditioning system for buildings become a necessity to provide comfort to occupants. In order to reduce the energy consumption of the air-conditioning system, the transmission of heat from outdoor to indoor space should be kept as minimum as possible. This article discuss about a technology to resist heat transfer through concrete wall panel using a hybrid method. In this research, PVC pipe was embedded at the center of concrete wall panel while the EPS foam beads were added about 1% of the cement content in the concrete mix forming the outer layer of the wall panel. Water is regulated in the PVC pipe from the rainwater harvesting system. The aim of this study is to minimize heat transfer from the external environment into the building. Internal building temperature which indicated in BS EN ISO 7730 or ASHRAE Standard 55 where the comfort indoor thermal is below 25°C during the daytime. Study observed that the internal surface temperature of heat resistance wall panel is up to 3°C lower than control wall panel. Therefore, we can conclude that application of heat resistance wall panel can lead to lower interior building temperature.

Multiparameter Assessments To Determine the Effects of Sugars and Antimicrobials on a Polymicrobial Oral Biofilm

PubMed Central

Yang, Ying; Sreenivasan, Prem K.; Subramanyam, Ravi; Cummins, Diane

2006-01-01

Clinical studies indicate relationships between dental plaque, a naturally formed biofilm, and oral diseases. The crucial role of nonmicrobial biofilm constituents in maintaining biofilm structure and biofilm-specific attributes, such as resistance to shear and viscoelasticity, is increasingly recognized. Concurrent analyses of the diverse nonmicrobial biofilm components for multiparameter assessments formed the focus of this investigation. Comparable numbers of Actinomyces viscosus, Streptococcus sanguinis, Streptococcus mutans, Neisseria subflava, and Actinobacillus actinomycetemcomitans cells were seeded into multiple wells of 96-well polystyrene plates for biofilm formation. Quantitative fluorescence and confocal laser scanning microscopy (CLSM) examined the influences of dietary sugars, incubation conditions, ingredients in oral hygiene formulations, and antibiotics on biofilm components. Biofilm extracellular polymeric substances (EPS) were examined with an optimized mixture of fluorescent lectins, with biofilm proteins, lipids, and nucleic acids detected with specific fluorescent stains. Anaerobic incubation of biofilms resulted in significantly more biofilm EPS and extractable carbohydrates than those formed under aerobic conditions (P < 0.05). Sucrose significantly enhanced biofilm EPS in comparison to fructose, galactose, glucose, and lactose (P < 0.05). CLSM demonstrated thicker biofilms under sucrose-replete conditions, along with significant increases in biofilm EPS, proteins, lipids, and nucleic acids, than under conditions of sucrose deficiency (P < 0.05). Agents in oral hygiene formulations (chlorhexidine, ethanol, and sodium lauryl sulfate), a mucolytic agent (N-acetyl-l-cysteine), and antibiotics with different modes of action (amoxicillin, doxycycline, erythromycin, metronidazole, and vancomycin) inhibited biofilm components (P < 0.05). Multiparameter analysis indicated a dose-dependent inhibition of biofilm EPS and protein by chlorhexidine and sodium lauryl sulfate, along with distinctive inhibitory patterns for subinhibitory concentrations of antibiotics. Collectively, these results highlight multiparameter assessments as a broad platform for simultaneous assessment of diverse biofilm components. PMID:17021225

Agglomeration of nano- and microplastic particles in seawater by autochthonous and de novo-produced sources of exopolymeric substances.

PubMed

Summers, Stephen; Henry, Theodore; Gutierrez, Tony

2018-05-01

Microplastics (<5 mm) have often been studied under in-vitro conditions where plastics have been investigated in isolation. However, in the natural environment microplastics readily form agglomerates conferring the particles with properties different to their pristine counterparts. Here, we examined the interaction of exopolymers with polystyrene nanoplastics and microplastics. Formation of plastic agglomerates was examined using simulated sea surface conditions. Flow cytometry coupled with microscopy revealed that nano- and microplastic particle spheres form agglomerates in seawater with a mucilagenous material and an associated microbial community. To characterise this material, differential staining methods revealed it to be glycoprotein in composition. Exposing increasing concentrations of a marine bacterial glycoprotein EPS to nano- or microplastics revealed that these types of polymers contribute to the formation and abundance of plastic agglomerates. This work highlights the importance of EPS on the fate of plastic and future research should take this into account when evaluating the impact of plastics. Crown Copyright © 2018. Published by Elsevier Ltd. All rights reserved.

Development of an attached microalgal growth system for biofuel production.

PubMed

Johnson, Michael B; Wen, Zhiyou

2010-01-01

Algal biofuel production has gained a renewed interest in recent years but is still not economically feasible due to several limitations related to algal culture. The objective of this study is to explore a novel attached culture system for growing the alga Chlorella sp. as biodiesel feedstock, with dairy manure wastewater being used as growth medium. Among supporting materials tested for algal attachment, polystyrene foam led to a firm attachment, high biomass yield (25.65 g/m(2), dry basis), and high fatty acid yield (2.31 g/m(2)). The biomass attached on the supporting material surface was harvested by scraping; the residual colonies left on the surface served as inoculum for regrowth. The algae regrowth on the colony-established surface resulted in a higher biomass yield than that from the initial growth on fresh surface due to the downtime saved for initial algal attachment. The 10-day regrowth culture resulted in a high biodiesel production potential with a fatty acid methyl esters yield of 2.59 g/m(2) and a productivity of 0.26 g/m(-2) day(-1). The attached algal culture also removed 61-79% total nitrogen and 62-93% total phosphorus from dairy manure wastewater, depending on different culture conditions. The biomass harvested from the attached growth system (through scraping) had a water content of 93.75%, similar to that harvested from suspended culture system (through centrifugation). Collectively, the attached algal culture system with polystyrene foam as a supporting material demonstrated a good performance in terms of biomass yield, biodiesel production potential, ease to harvest biomass, and physical robustness for reuse.

Study of combustion and emission characteristics of fuel derived from waste plastics by various waste to energy (W-t-E) conversion processes

NASA Astrophysics Data System (ADS)

Hazrat, M. A.; Rasul, M. G.; Khan, M. M. K.

2016-07-01

Reduction of plastic wastes by means of producing energy can be treated as a good investment in the waste management and recycling sectors. In this article, conversion of plastics into liquid fuel by two thermo-chemical processes, pyrolysis and gasification, are reviewed. The study showed that the catalytic pyrolysis of homogenous waste plastics produces better quality and higher quantity of liquefied fuel than that of non-catalytic pyrolysis process at a lower operating temperature. The syngas produced from gasification process, which occurs at higher temperature than the pyrolysis process, can be converted into diesel by the Fischer-Tropsch (FT) reaction process. Conducive bed material like Olivine in the gasification conversion process can remarkably reduce the production of tar. The waste plastics pyrolysis oil showed brake thermal efficiency (BTE) of about 27.75%, brake specific fuel consumption (BSFC) of 0.292 kg/kWh, unburned hydrocarbon emission (uHC) of 91 ppm and NOx emission of 904 ppm in comparison with the diesel for BTE of 28%, BSFC of 0.276 kg/kWh, uHC of 57 ppm and NOx of 855 ppm. Dissolution of Polystyrene (PS) into biodiesel also showed the potential of producing alternative transport fuel. It has been found from the literature that at higher engine speed, increased EPS (Expanded Polystyrene) quantity based biodiesel blends reduces CO, CO2, NOx and smoke emission. EPS-biodiesel fuel blend increases the brake thermal efficiency by 7.8%, specific fuel consumption (SFC) by 7.2% and reduces brake power (Pb) by 3.2%. More study using PS and EPS with other thermoplastics is needed to produce liquid fuel by dissolving them into biodiesel and to assess their suitability as a transport fuel. Furthermore, investigation to find out most suitable W-t-E process for effective recycling of the waste plastics as fuel for internal combustion engines is necessary to reduce environmental pollution and generate revenue which will be addressed in this article.

DOE ZERH Case Study: Hammer and Hand, Pumpkin Ridge Passive House, North Plains, OR

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

Case study of a DOE 2015 Housing Innovation Award winning custom home in the marine climate that got a HERS 49 without PV, or HERS 5 with PV, with 2x4 24” on center walls plus 8” exterior cavity together dense-packed with R-60 cellulose; daylight basement with R-29 rigid EPS foam under slab; vented attic with R-86 blown cellulose; minisplit heat pump; ducted with HRV; 15.5 SEER; 10 HSPF.

A comparison of the physical, chemical, and biological properties of sludges from a complete-mix activated sludge reactor and a submerged membrane bioreactor.

PubMed

Merlo, Rion P; Trussell, R Shane; Hermanowicz, Slawomir W; Jenkins, David

2007-03-01

The properties of sludges from a pilot-scale submerged membrane bioreactor (SMBR) and two bench-scale complete-mix, activated sludge (CMAS) reactors treating municipal primary effluent were determined. Compared with the CMAS sludges, the SMBR sludge contained a higher amount of soluble microbial products (SMP) and colloidal material attributed to the use of a membrane for solid-liquid separation; a higher amount nocardioform bacteria, resulting from efficient foam trapping; and a lower amount of extracellular polymeric substances (EPS), possibly because there was no selective pressure for the sludge to settle. High aeration rates in both the CMAS and SMBR reactors produced sludges with higher numbers of smaller particles. Normalized capillary suction time values for the SMBR sludge were lower than for the CMAS sludges, possibly because of its lower EPS content.

Extracellular plasma RNA from colon cancer patients is confined in a vesicle-like structure and is mRNA-enriched

PubMed Central

García, José Miguel; García, Vanesa; Peña, Cristina; Domínguez, Gemma; Silva, Javier; Diaz, Raquel; Espinosa, Pablo; Citores, Maria Jesús; Collado, Manuel; Bonilla, Félix

2008-01-01

Little is yet known about the origin and protective mechanism of free nucleic acids in plasma. We investigated the possibility of these free nucleic acids being particle associated. Plasma samples from colon cancer patients and cell culture media were subjected to various antibody incubations, ultracentrifugation, and RNA extraction protocols for total RNA, epithelial RNA, and mRNA. Flow cytometry using a Ber-EP4 antibody and confocal laser microscopy after staining with propidium iodide were also performed. mRNA levels of the LISCH7 and SDHA genes were determined in cells and in culture media. Ber-EP4 antibody and polystyrene beads coated with oligo dT sequences were employed. We observed that, after incubation, total RNA and mRNA were always detected after membrane digestion, and that epithelial RNA was detected before this procedure. In ultracentrifugation, mRNA was caught in the supernatant only if a former lysis mediated or in the pellet if there was no previous digestion. Flow cytometry determinations showed that antibody-coated microbeads keep acellular structures bearing epithelial antigens apart. Confocal laser microscopy made 1- to 2-μm-diameter particles perceptible in the vicinity of magnetic polystyrene beads. Relevant differences were observed between mRNA of cells and culture media, as there was a considerable difference in LISCH7 mRNA levels between HT29 and IMR90 cell co-cultures and their culture media. Our results support the view that extracellular RNA found in plasma from cancer patients circulates in association with or is protected in a multiparticle complex, and that an active release mechanism by tumor cells may be a possible origin. PMID:18456845

Single-mode Rayleigh-Taylor growth-rate measurements with the OMEGA laser system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knauer, J. P.; Verdon, C. P.; Meyerhofer, D. D.

1997-04-15

The results from a series of single-mode Rayleigh-Taylor (RT) instability growth experiments performed on the OMEGA laser system using planar targets are reported. Planar targets with imposed mass perturbations were accelerated using five to six 351-nm laser beams overlapped with total intensities up to 2.5x10{sup 14} W/cm{sup 2}. Experiments were performed with both 3-ns ramp and 3-ns flat-topped temporal pulse shapes. The use of distributed phase plates and smoothing by spectral dispersion resulted in a laser-irradiation nonuniformity of 4%-7% over a 600-{mu}m-diam region defined by the 90% intensity contour. The temporal growth of the modulation in optical depth was measuredmore » using through-foil radiography and was detected with an x-ray framing camera for CH targets with and without a foam buffer. The growth of both 31-{mu}m and 60-{mu}m wavelength perturbations was found to be in good agreement with ORCHID simulations when the experimental details, including noise, were included. The addition of a 30-mg/cc, 100-{mu}m-thick polystyrene foam buffer layer resulted in reduced growth of the 31-{mu}m perturbation and essentially unchanged growth for the 60-{mu}m case when compared to targets without foam.« less

PAHs in polystyrene food contact materials: An unintended consequence.

PubMed

Li, Si-Qi; Ni, Hong-Gang; Zeng, Hui

2017-12-31

Eight low-ring PAHs were detected in 21 polystyrene (PS) food contact materials (FCMs) samples while high-ring PAHs (>4 rings) were not found. This is because the reaction pathway for formation of high-ring PAHs consists of more steps than it does for low-high PAHs. The concentrations of Σ 8 PAH were from 18.9±5.16ng/g for product colorless fruit fork to 476±52.0ng/g for foam instant noodle container. These data were far beyond levels of PAHs in other plastics. Of the eight PAHs detected, Phe had the highest average concentration, followed by Nap. These two PAHs collectively accounted for over 80% of the Σ 8 PAH concentrations in all PS FCMs. Levels of Σ 8 PAH in expanded PS FCMs were higher than those in extruded ones due to utilization of foaming agent. The concentrations of Σ 8 PAH were lower in colorless PS FCMs than in colored ones. Auxochromes and chromophores contributed to the change of short-chain hydrocarbons to aromatic hydrocarbon. Simulated migration values of PAHs from PS FCMs to food varied widely. The migration value of Σ 8 PAH with maximum probability was below 10ng/g, which the maximum tolerated migration level for substance according to the European Union standards. However, higher migration values were possible and the potential health risk should still be concerned because the simulated migration displayed a log-normal distribution. Furthermore, water was used as food simulant would always lead to an underestimate of PAHs migration to real daily food, and then lead to an underestimate of risk. Copyright © 2017 Elsevier B.V. All rights reserved.

Safety Performance of Exterior Wall Insulation Material Based on Large Security Concept

NASA Astrophysics Data System (ADS)

Zuo, Q. L.; Wang, Y. J.; Li, J. S.

2018-05-01

In order to evaluate the fire spread characteristics of building insulation materials under corner fire, an experiment is carried out with small-scale fire spread test system. The change rule of the parameters such as the average height of the flame, the average temperature of the flame and the shape of the flame are analyzed. The variations of the fire spread characteristic parameters of the building insulation materials are investigated. The results show that the average temperature of Expanded Polystyrene (EPS) board, with different thickness, decrease - rise - decrease - increase. During the combustion process, the fire of 4cm thick plate spreads faster.

Simulation of CO2 Solubility in Polystyrene-b-Polybutadieneb-Polystyrene (SEBS) by artificial intelligence network (ANN) method

NASA Astrophysics Data System (ADS)

Sharudin, R. W.; AbdulBari Ali, S.; Zulkarnain, M.; Shukri, M. A.

2018-05-01

This study reports on the integration of Artificial Neural Network (ANNs) with experimental data in predicting the solubility of carbon dioxide (CO2) blowing agent in SEBS by generating highest possible value for Regression coefficient (R2). Basically, foaming of thermoplastic elastomer with CO2 is highly affected by the CO2 solubility. The ability of ANN in predicting interpolated data of CO2 solubility was investigated by comparing training results via different method of network training. Regards to the final prediction result for CO2 solubility by ANN, the prediction trend (output generate) was corroborated with the experimental results. The obtained result of different method of training showed the trend of output generated by Gradient Descent with Momentum & Adaptive LR (traingdx) required longer training time and required more accurate input to produce better output with final Regression Value of 0.88. However, it goes vice versa with Levenberg-Marquardt (trainlm) technique as it produced better output in quick detention time with final Regression Value of 0.91.

A method for increase abrasive wear resistance parts by obtaining on methods casting on gasifying models

NASA Astrophysics Data System (ADS)

Sedukhin, V. V.; Anikeev, A. N.; Chumanov, I. V.

2017-11-01

Method optimizes hardening working layer parts’, working in high-abrasive conditions looks in this work: bland refractory particles WC and TiC in respect of 70/30 wt. % prepared by beforehand is applied on polystyrene model in casting’ mould. After metal poured in mould, withstand for crystallization, and then a study is carried out. Study macro- and microstructure received samples allows to say that thickness and structure received hardened layer depends on duration interactions blend harder carbides and liquid metal. Different character interactions various dispersed particles and matrix metal observed under the same conditions. Tests abrasive wear resistance received materials of method calculating residual masses was conducted in laboratory’ conditions. Results research wear resistance showed about that method obtaining harder coating of blend carbide tungsten and carbide titanium by means of drawing on surface foam polystyrene model before moulding, allows receive details with surface has wear resistance in 2.5 times higher, than details of analogy steel uncoated. Wherein energy costs necessary for transformation units mass’ substances in powder at obtained harder layer in 2.06 times higher, than materials uncoated.

Mitigating Settlement of Structures founded on Peat

NASA Astrophysics Data System (ADS)

Wijeyesekera, D. C.; Numbikannu, L.; Ismail, T. N. H. T.; Bakar, I.

2016-07-01

Observations made of two common failures of structures founded on peat/organic soil in Johor, Malaysia is presented. Critical evaluation of current lightweight fill technology to mitigate such settlement is also discussed. Lightweight technology, such as Expanded Polystyrene (EPS), has been used in construction on soft yielding ground for decades. Regrettably, some published information of EPS failures to perform on construction sites are also cited in this paper. This paper outlines some concepts leading to the development of an alternative innovative lightweight fill is that the idealised cellular structure of the GCM permit free flow of water and complemented by the mat structure which evens out any differential settlement A further highlight of this paper is the monitoring of the field performance of this lightweight fill (GCM) as a feasible alternative to fill weight reduction on yielding ground.. Hence, a prime research objective was to compare the fill settlements observed with 1m high fill of surcharge loading on peat ground (comparison of the case of using a partial 0.6m high GCM and that of a total of 1m of conventional sand backfill).

Separating large microscale particles by exploiting charge differences with dielectrophoresis.

PubMed

Polniak, Danielle V; Goodrich, Eric; Hill, Nicole; Lapizco-Encinas, Blanca H

2018-04-13

Dielectrophoresis (DEP), the migration of particles due to polarization effects under the influence of a nonuniform electric field, was employed for characterizing the behavior and achieving the separation of larger (diameter >5 μm) microparticles by exploiting differences in electrical charge. Usually, electrophoresis (EP) is the method of choice for separating particles based on differences in electrical charge; however, larger particles, which have low electrophoretic mobilities, cannot be easily separated with EP-based techniques. This study presents an alternative for the characterization, assessment, and separation of larger microparticles, where charge differences are exploited with DEP instead of EP. Polystyrene microparticles with sizes varying from 5 to 10 μm were characterized employing microdevices for insulator-based dielectrophoresis (iDEP). Particles within an iDEP microchannel were exposed simultaneously to DEP, EP, and electroosmotic (EO) forces. The electrokinetic behavior of four distinct types of microparticles was carefully characterized by means of velocimetry and dielectrophoretic capture assessments. As a final step, a dielectropherogram separation of two distinct types of 10 μm particles was devised by first characterizing the particles and then performing the separation. The two types of 10 μm particles were eluted from the iDEP device as two separate peaks of enriched particles in less than 80 s. It was demonstrated that particles with the same size, shape, surface functionalization, and made from the same bulk material can be separated with iDEP by exploiting slight differences in the magnitude of particle charge. The results from this study open the possibility for iDEP to be used as a technique for the assessment and separation of biological cells that have very similar characteristics (shape, size, similar make-up), but slight variance in surface electrical charge. Copyright © 2018 Elsevier B.V. All rights reserved.

OSIRIS Modeling of High Energy Electron Transport in Warm Dense Matter

NASA Astrophysics Data System (ADS)

May, J.; Yabuuchi, T.; McGuffey, C.; Wei, Ms; Beg, F.; Mori, Wb

2016-10-01

In experiments on the Omega EP laser, a high intensity laser beam (eA /me c > 1) is focused onto a gold foil, generating relativistic electrons. Behind the Au foil is a layer of plastic foam through which the electrons are allowed to transport, and on the far side of the CH from the gold is a copper foil; electron fluence is measured by recording the k- α from that foil. The foam layer is either pre-ionized via a shock launched from an ablator irradiated earlier with a beam perpendicular to the high intensity beam; or the foam is in the solid state when the high intensity beam is switched on. In the latter case the foam - which has an initial density of 200mg /cm3 - heats to a temperature of 40eV and rarifies to a density of 30mg /cm3 . Results show an order of magnitude decrease in k- α when the CH layer is pre-ionized compared to cold CH. OSIRIS simulations indicate that the primary explanation for the difference in transport seen in the experiment is the partial resistive collimation of the beam in the higher density material, caused by collisional resistivity. The effect seems to be mostly caused by the higher density itself, with temperature having minimal effect. The authors acknowledge the support of the Department of Energy under contract DE-NA 0001833 and the National Science Foundation under contract ACI 1339893.

Single-mode Rayleigh-Taylor growth-rate measurements with the OMEGA laser system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knauer, J.P.; Verdon, C.P.; Meyerhofer, D.D.

1997-04-01

The results from a series of single-mode Rayleigh-Taylor (RT) instability growth experiments performed on the OMEGA laser system using planar targets are reported. Planar targets with imposed mass perturbations were accelerated using five to six 351-nm laser beams overlapped with total intensities up to 2.5{times}10{sup 14}W/cm{sup 2}. Experiments were performed with both 3-ns ramp and 3-ns flat-topped temporal pulse shapes. The use of distributed phase plates and smoothing by spectral dispersion resulted in a laser-irradiation nonuniformity of 4{percent}{endash}7{percent} over a 600-{mu}m-diam region defined by the 90{percent} intensity contour. The temporal growth of the modulation in optical depth was measured usingmore » through-foil radiography and was detected with an x-ray framing camera for CH targets with and without a foam buffer. The growth of both 31-{mu}m and 60-{mu}m wavelength perturbations was found to be in good agreement with {ital ORCHID} simulations when the experimental details, including noise, were included. The addition of a 30-mg/cc, 100-{mu}m-thick polystyrene foam buffer layer resulted in reduced growth of the 31-{mu}m perturbation and essentially unchanged growth for the 60-{mu}m case when compared to targets without foam. {copyright} {ital 1997 American Institute of Physics.}« less

On some physical and dynamical properties of microplastic particles in marine environment.

PubMed

Chubarenko, I; Bagaev, A; Zobkov, M; Esiukova, E

2016-07-15

Simplified physical models and geometrical considerations reveal general physical and dynamical properties of microplastic particles (0.5-5mm) of different density, shape and size in marine environment. Windage of extremely light foamed particles, surface area and fouling rate of slightly positively buoyant microplastic spheres, films and fibres and settling velocities of negatively buoyant particles are analysed. For the Baltic Sea dimensions and under the considered idealised external conditions, (i) only one day is required for a foamed polystyrene particle to cross the sea (ca. 250km); (ii) polyethylene fibres should spend about 6-8months in the euphotic zone before sinking due to bio-fouling, whilst spherical particles can be retained on the surface up to 10-15years; (iii) for heavy microplastic particles, the time of settling through the water column in the central Gotland basin (ca. 250m) is less than 18h. Proper physical setting of the problem of microplastics transport and developing of physically-based parameterisations are seen as applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Readily available titania nanostructuring routines based on mobility and polarity controlled phase separation of an amphiphilic diblock copolymer.

PubMed

Hohn, Nuri; Schlosser, Steffen J; Bießmann, Lorenz; Grott, Sebastian; Xia, Senlin; Wang, Kun; Schwartzkopf, Matthias; Roth, Stephan V; Müller-Buschbaum, Peter

2018-03-15

The amphiphilic diblock copolymer polystyrene-block-polyethylene oxide is combined with sol-gel chemistry to control the structure formation of blade-coated foam-like titania thin films. The influence of evaporation time before immersion into a poor solvent bath and polarity of the poor solvent bath are studied. Resulting morphological changes are quantified by scanning electron microscopy (SEM) and grazing incidence small angle X-ray scattering (GISAXS) measurements. SEM images surface structures while GISAXS accesses inner film structures. Due to the correlation of evaporation time and mobility of the polymer template during the phase separation process, a decrease in the distances of neighboring titania nanostructures from 50 nm to 22 nm is achieved. Furthermore, through an increase of polarity of an immersion bath the energetic incompatibility of the hydrophobic block and the solvent can be enhanced, leading to an increase of titania nanostructure distances from 35 nm to 55 nm. Thus, a simple approach is presented to control titania nanostructure in foam-like films prepared via blade coating, which enables an easy upscaling of film preparation.

Exterior Rigid Foam Insulation at the Edge of a Slab Foundation, Fresno, California (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Exterior rigid foam insulation at the edge of the slab foundation was a unique feature for this low-load, unoccupied test house in a hot-dry climate and may be more appropriate for climates with higher heating loads. U.S. Department of Energy Building America research team IBACOS worked with National Housing Quality Award winner Wathen-Castanos Hybrid Homes, Inc., to assess the performance of this feature in a single-family detached ranch house with three bedrooms and two full bathrooms constructed on a slab-on-grade foundation in Fresno, California. One challenge during installation of the system was the attachment of the butyl flashing to themore » open framing. To solve this constructability issue, the team added a nailer to the base of the wall to properly attach and lap the flashing. In this strategy, R-7.5, 1.5-in.-thick extruded polystyrene was installed on the exterior of the slab for a modeled savings of 4,500 Btu/h on the heating load.« less

New Whole-House Solutions Case Study: Exterior Rigid Foam Insulation at the Edge of a Slab Foundation, Fresno, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Exterior rigid foam insulation at the edge of the slab foundation was a unique feature for this low-load, unoccupied test house in a hot-dry climate and may be more appropriate for climates with higher heating loads. U.S. Department of Energy Building America research team IBACOS worked with National Housing Quality Award winner Wathen-Castanos Hybrid Homes, Inc., to assess the performance of this feature in a single-family detached ranch house with three bedrooms and two full bathrooms constructed on a slab-on-grade foundation in Fresno, California. One challenge during installation of the system was the attachment of the butyl flashing to themore » open framing. To solve this constructability issue, the team added a nailer to the base of the wall to properly attach and lap the flashing. In this strategy, R-7.5, 1.5-in.-thick extruded polystyrene was installed on the exterior of the slab for a modeled savings of 4,500 Btu/h on the heating load.« less

X-ray digital industrial radiography (DIR) for local liquid velocity (VLL) measurement in trickle bed reactors (TBRs): Validation of the technique

NASA Astrophysics Data System (ADS)

Mohd Salleh, Khairul Anuar; Rahman, Mohd Fitri Abdul; Lee, Hyoung Koo; Al Dahhan, Muthanna H.

2014-06-01

Local liquid velocity measurements in Trickle Bed Reactors (TBRs) are one of the essential components in its hydrodynamic studies. These measurements are used to effectively determine a reactor's operating condition. This study was conducted to validate a newly developed technique that combines Digital Industrial Radiography (DIR) with Particle Tracking Velocimetry (PTV) to measure the Local Liquid Velocity (VLL) inside TBRs. Three millimeter-sized Expanded Polystyrene (EPS) beads were used as packing material. Three validation procedures were designed to test the newly developed technique. All procedures and statistical approaches provided strong evidence that the technique can be used to measure the VLL within TBRs.

X-ray digital industrial radiography (DIR) for local liquid velocity (V(LL)) measurement in trickle bed reactors (TBRs): validation of the technique.

PubMed

Mohd Salleh, Khairul Anuar; Rahman, Mohd Fitri Abdul; Lee, Hyoung Koo; Al Dahhan, Muthanna H

2014-06-01

Local liquid velocity measurements in Trickle Bed Reactors (TBRs) are one of the essential components in its hydrodynamic studies. These measurements are used to effectively determine a reactor's operating condition. This study was conducted to validate a newly developed technique that combines Digital Industrial Radiography (DIR) with Particle Tracking Velocimetry (PTV) to measure the Local Liquid Velocity (V(LL)) inside TBRs. Three millimeter-sized Expanded Polystyrene (EPS) beads were used as packing material. Three validation procedures were designed to test the newly developed technique. All procedures and statistical approaches provided strong evidence that the technique can be used to measure the V(LL) within TBRs.

Modeling Transport of Relativistic Electrons through Warm-Dense Matter Using Collisional PIC

NASA Astrophysics Data System (ADS)

May, J.; McGuffey, C.; Yabuuchi, T.; Wei, Ms; Beg, F.; Mori, Wb

2017-10-01

In electron transport experiments performed on the OMEGA EP laser system, a relativistic electron beam was created by focusing a high intensity (eA /me c > 1) laser onto a gold (Au) foil. Behind the Au foil was a layer of plastic (CH) foam, with an initial density of 200mg /cm3 . Before the high intensity laser was switched on, this foam was either left unperturbed; or it was shocked using a lower intensity laser (eA /me c 10-4) with beam path perpendicular to the high intensity laser, which left the CH layer in a warm dense matter (WDM) state with temperature of 40 eV and density of 30mg /cm3 . The electron beam was imaged by observing the k- α signal from a copper foil on the far side from the Au. The result was that transport was decreased by an order of magnitude in the WDM compared to the cold foam. We have modeled this experiment using the PIC code OSIRIS, with also a Monte Carlo Coulomb collision package. Our simulations indicate that the main cause of the differences in transport is a collimating magnetic field in the higher density, cold foam, created by collisional resistivity. The plasma density of the Au layer, difficult to model fully in PIC, appears to effect the heat capacity and therefore temperature and resistivity of the target. The authors acknowledge the support of the Department of Energy under contract DE-NA 0001833 and the National Science Foundation under contract ACI 1339893.

Prediction of the Effective Thermal Conductivity of Powder Insulation

NASA Astrophysics Data System (ADS)

Jin, Lingxue; Park, Jiho; Lee, Cheonkyu; Jeong, Sangkwon

The powder insulation method is widely used in structural and cryogenic systems such as transportation and storage tanks of cryogenic fluids. The powder insulation layer is constructed by small particle powder with light weight and some residual gas with high porosity. So far, many experiments have been carried out to test the thermal performance of various kinds of powder, including expanded perlite, glass microspheres, expanded polystyrene (EPS). However, it is still difficult to predict the thermal performance of powder insulation by calculation due to the complicated geometries, including various particle shapes, wide powder diameter distribution, and various pore sizes. In this paper, the effective thermal conductivity of powder insulation has been predicted based on an effective thermal conductivity calculationmodel of porous packed beds. The calculation methodology was applied to the insulation system with expanded perlite, glass microspheres and EPS beads at cryogenic temperature and various vacuum pressures. The calculation results were compared with previous experimental data. Moreover, additional tests were carried out at cryogenic temperature in this research. The fitting equations of the deformation factor of the area-contact model are presented for various powders. The calculation results show agood agreement with the experimental results.

Biodegradation of polystyrene wastes in yellow mealworms (larvae of Tenebrio molitor Linnaeus): Factors affecting biodegradation rates and the ability of polystyrene-fed larvae to complete their life cycle.

PubMed

Yang, Shan-Shan; Brandon, Anja Malawi; Andrew Flanagan, James Christopher; Yang, Jun; Ning, Daliang; Cai, Shen-Yang; Fan, Han-Qing; Wang, Zhi-Yue; Ren, Jie; Benbow, Eric; Ren, Nan-Qi; Waymouth, Robert M; Zhou, Jizhong; Criddle, Craig S; Wu, Wei-Min

2018-01-01

Commercial production of polystyrene (PS) -a persistent plastic that is not biodegradable at appreciable rates in most environments-has led to its accumulation as a major contaminant of land, rivers, lakes, and oceans. Recently, however, an environment was identified in which PS is susceptible to rapid biodegradation: the larval gut of Tenebrio molitor Linnaeus (yellow mealworms). In this study, we evaluate PS degradation capabilities of a previously untested strain of T. molitor and assess its survival and PS biodegradation rates for a range of conditions (two simulated food wastes, three temperatures, seven PS waste types). For larvae fed PS alone, the %PS removed in the short (12-15 h) residence time of the mealworm gut gradually increased for 2-3 weeks then stabilized at values up to 65%. Thirty two-day survival rates were >85% versus 54% for unfed larvae. For mealworms fed ∼10% w/w PS and ∼90% bran, an agricultural byproduct, rates of PS degradation at 25 °C nearly doubled compared to mealworms fed PS alone. Polymer residues in the frass showed evidence of partial depolymerization and oxidation. All of the tested PS wastes degraded, with the less dense foams degrading most rapidly. Mealworms fed bran and PS completed all life cycle stages (larvae, pupae, beetles, egg), and the second generation had favorable PS degradation, opening the door for selective breeding. Copyright © 2017 Elsevier Ltd. All rights reserved.

A Study on Variation of Thermal Characteristics of Insulation Materials for Buildings According to Actual Long-Term Annual Aging Variation

NASA Astrophysics Data System (ADS)

Choi, Hyun-Jung; Kang, Jae-Sik; Huh, Jung-Ho

2018-01-01

Insulation materials used for buildings are broadly classified as organic insulation materials or inorganic insulation materials. Foam gas is used for producing organic insulation materials. The thermal conductivity of foam gas is generally lower than that of air. As a result, foam gas is discharged over time and replaced by outside air that has relatively less thermal resistance. The gas composition ratio in air bubbles inside the insulation materials changes rapidly, causing the performance degradation of insulation materials. Such performance degradation can be classified into different stages. Stage 1 appears to have a duration of 5 years, and Stage 2 takes a period of over 10 years. In this study, two insulation materials that are most frequently used in South Korea were analyzed, focusing on the changes thermal resistance for the period of over 5000 days. The measurement result indicated that the thermal resistance of expanded polystyrene fell below the KS performance standards after about 80-150 days from its production date. After about 5000 days, its thermal resistance decreased by 25.7 % to 42.7 % in comparison with the initial thermal resistance. In the case of rigid polyurethane, a pattern of rapid performance degradation appeared about 100 days post-production, and the thermal resistance fell below the KS performance standards after about 1000 days. The thermal resistance decreased by 22.5 % to 27.4 % in comparison with the initial thermal resistance after about 5000 days.

Seismic performance of geosynthetic-soil retaining wall structures

NASA Astrophysics Data System (ADS)

Zarnani, Saman

Vertical inclusions of expanded polystyrene (EPS) placed behind rigid retaining walls were investigated as geofoam seismic buffers to reduce earthquake-induced loads. A numerical model was developed using the program FLAC and the model validated against 1-g shaking table test results of EPS geofoam seismic buffer models. Two constitutive models for the component materials were examined: elastic-perfectly plastic with Mohr-Coulomb (M-C) failure criterion and non-linear hysteresis damping model with equivalent linear method (ELM) approach. It was judged that the M-C model was sufficiently accurate for practical purposes. The mechanical property of interest to attenuate dynamic loads using a seismic buffer was the buffer stiffness defined as K = E/t (E = buffer elastic modulus, t = buffer thickness). For the range of parameters investigated in this study, K ≤50 MN/m3 was observed to be the practical range for the optimal design of these systems. Parametric numerical analyses were performed to generate design charts that can be used for the preliminary design of these systems. A new high capacity shaking table facility was constructed at RMC that can be used to study the seismic performance of earth structures. Reduced-scale models of geosynthetic reinforced soil (GRS) walls were built on this shaking table and then subjected to simulated earthquake loading conditions. In some shaking table tests, combined use of EPS geofoam and horizontal geosynthetic reinforcement layers was investigated. Numerical models were developed using program FLAC together with ELM and M-C constitutive models. Physical and numerical results were compared against predicted values using analysis methods found in the journal literature and in current North American design guidelines. The comparison shows that current Mononobe-Okabe (M-O) based analysis methods could not consistently satisfactorily predict measured reinforcement connection load distributions at all elevations under both static and dynamic loading conditions. The results from GRS model wall tests with combined EPS geofoam and geosynthetic reinforcement layers show that the inclusion of a EPS geofoam layer behind the GRS wall face can reduce earth loads acting on the wall facing to values well below those recorded for conventional GRS wall model configurations.

Gyroid Nickel Nanostructures from Diblock Copolymer Supramolecules

PubMed Central

Vukovic, Ivana; Punzhin, Sergey; Voet, Vincent S. D.; Vukovic, Zorica; de Hosson, Jeff Th. M.; ten Brinke, Gerrit; Loos, Katja

2014-01-01

Nanoporous metal foams possess a unique combination of properties - they are catalytically active, thermally and electrically conductive, and furthermore, have high porosity, high surface-to-volume and strength-to-weight ratio. Unfortunately, common approaches for preparation of metallic nanostructures render materials with highly disordered architecture, which might have an adverse effect on their mechanical properties. Block copolymers have the ability to self-assemble into ordered nanostructures and can be applied as templates for the preparation of well-ordered metal nanofoams. Here we describe the application of a block copolymer-based supramolecular complex - polystyrene-block-poly(4-vinylpyridine)(pentadecylphenol) PS-b-P4VP(PDP) - as a precursor for well-ordered nickel nanofoam. The supramolecular complexes exhibit a phase behavior similar to conventional block copolymers and can self-assemble into the bicontinuous gyroid morphology with two PS networks placed in a P4VP(PDP) matrix. PDP can be dissolved in ethanol leading to the formation of a porous structure that can be backfilled with metal. Using electroless plating technique, nickel can be inserted into the template's channels. Finally, the remaining polymer can be removed via pyrolysis from the polymer/inorganic nanohybrid resulting in nanoporous nickel foam with inverse gyroid morphology. PMID:24797367

Gyroid nickel nanostructures from diblock copolymer supramolecules.

PubMed

Vukovic, Ivana; Punzhin, Sergey; Voet, Vincent S D; Vukovic, Zorica; de Hosson, Jeff Th M; ten Brinke, Gerrit; Loos, Katja

2014-04-28

Nanoporous metal foams possess a unique combination of properties - they are catalytically active, thermally and electrically conductive, and furthermore, have high porosity, high surface-to-volume and strength-to-weight ratio. Unfortunately, common approaches for preparation of metallic nanostructures render materials with highly disordered architecture, which might have an adverse effect on their mechanical properties. Block copolymers have the ability to self-assemble into ordered nanostructures and can be applied as templates for the preparation of well-ordered metal nanofoams. Here we describe the application of a block copolymer-based supramolecular complex - polystyrene-block-poly(4-vinylpyridine)(pentadecylphenol) PS-b-P4VP(PDP) - as a precursor for well-ordered nickel nanofoam. The supramolecular complexes exhibit a phase behavior similar to conventional block copolymers and can self-assemble into the bicontinuous gyroid morphology with two PS networks placed in a P4VP(PDP) matrix. PDP can be dissolved in ethanol leading to the formation of a porous structure that can be backfilled with metal. Using electroless plating technique, nickel can be inserted into the template's channels. Finally, the remaining polymer can be removed via pyrolysis from the polymer/inorganic nanohybrid resulting in nanoporous nickel foam with inverse gyroid morphology.

Spontaneous formation of nanostructures inside inkjet-printed colloidal drops

NASA Astrophysics Data System (ADS)

Yang, Xin; Thorne, Nathaniel; Sun, Ying

2013-11-01

Nanostructures formed in inkjet-printed colloidal drops are systematically examined with different substrates and ink formulations. Various deposition patterns from multi-ring, radial spoke, firework to spider web, foam and island structures are observed. With a high particle loading, deposition transitions from multi-ring near the drop edge to spider web and finally to foam and islands in the center of the drop with 20 nm sulfate-modified polystyrene particles. At the same particle loading, 200 nm particles self-assemble into radial spokes at the drop edge and islands in the center, due to reduced contact line pinning resulted from less particles. In drops with a low particle concentration, due to fingering instability of the contact line, 20 nm particles form radial spokes enclosed by a ring, while 200 nm particles assemble into firework-like structures without a ring. Moreover, at a high particle loading, ruptures are observed on the multi-ring structure formed by 20 nm carboxylic-modified particles, due to stronger capillary forces from the contact line. Furthermore, for a drop printed on a less hydrophilic substrate, the interparticle interactions enable a more uniform deposition rather than complex nanostructures.

High-throughput particle manipulation by hydrodynamic, electrokinetic, and dielectrophoretic effects in an integrated microfluidic chip

PubMed Central

Li, Shunbo; Li, Ming; Bougot-Robin, Kristelle; Cao, Wenbin; Yeung Yeung Chau, Irene; Li, Weihua; Wen, Weijia

2013-01-01

Integrating different steps on a chip for cell manipulations and sample preparation is of foremost importance to fully take advantage of microfluidic possibilities, and therefore make tests faster, cheaper and more accurate. We demonstrated particle manipulation in an integrated microfluidic device by applying hydrodynamic, electroosmotic (EO), electrophoretic (EP), and dielectrophoretic (DEP) forces. The process involves generation of fluid flow by pressure difference, particle trapping by DEP force, and particle redirect by EO and EP forces. Both DC and AC signals were applied, taking advantages of DC EP, EO and AC DEP for on-chip particle manipulation. Since different types of particles respond differently to these signals, variations of DC and AC signals are capable to handle complex and highly variable colloidal and biological samples. The proposed technique can operate in a high-throughput manner with thirteen independent channels in radial directions for enrichment and separation in microfluidic chip. We evaluated our approach by collecting Polystyrene particles, yeast cells, and E. coli bacteria, which respond differently to electric field gradient. Live and dead yeast cells were separated successfully, validating the capability of our device to separate highly similar cells. Our results showed that this technique could achieve fast pre-concentration of colloidal particles and cells and separation of cells depending on their vitality. Hydrodynamic, DC electrophoretic and DC electroosmotic forces were used together instead of syringe pump to achieve sufficient fluid flow and particle mobility for particle trapping and sorting. By eliminating bulky mechanical pumps, this new technique has wide applications for in situ detection and analysis. PMID:24404011

High-throughput particle manipulation by hydrodynamic, electrokinetic, and dielectrophoretic effects in an integrated microfluidic chip.

PubMed

Li, Shunbo; Li, Ming; Bougot-Robin, Kristelle; Cao, Wenbin; Yeung Yeung Chau, Irene; Li, Weihua; Wen, Weijia

2013-01-01

Integrating different steps on a chip for cell manipulations and sample preparation is of foremost importance to fully take advantage of microfluidic possibilities, and therefore make tests faster, cheaper and more accurate. We demonstrated particle manipulation in an integrated microfluidic device by applying hydrodynamic, electroosmotic (EO), electrophoretic (EP), and dielectrophoretic (DEP) forces. The process involves generation of fluid flow by pressure difference, particle trapping by DEP force, and particle redirect by EO and EP forces. Both DC and AC signals were applied, taking advantages of DC EP, EO and AC DEP for on-chip particle manipulation. Since different types of particles respond differently to these signals, variations of DC and AC signals are capable to handle complex and highly variable colloidal and biological samples. The proposed technique can operate in a high-throughput manner with thirteen independent channels in radial directions for enrichment and separation in microfluidic chip. We evaluated our approach by collecting Polystyrene particles, yeast cells, and E. coli bacteria, which respond differently to electric field gradient. Live and dead yeast cells were separated successfully, validating the capability of our device to separate highly similar cells. Our results showed that this technique could achieve fast pre-concentration of colloidal particles and cells and separation of cells depending on their vitality. Hydrodynamic, DC electrophoretic and DC electroosmotic forces were used together instead of syringe pump to achieve sufficient fluid flow and particle mobility for particle trapping and sorting. By eliminating bulky mechanical pumps, this new technique has wide applications for in situ detection and analysis.

Exploring the Disappearing Ocean Micro Plastic Mystery: New Insights from Dissolved Organic Carbon photo production

NASA Astrophysics Data System (ADS)

Zhu, L.; Zhao, S.; Li, D.; Stubbins, A.

2017-12-01

Emerging as a novel planetary threat, plastic waste, dominated by millimeter-sized plastic (microplastic), is omnipresent in the oceans, posing broad environmental threats. However, only 1% of the microplastic waste exported from the land is found in the ocean. Most of the lost fraction is in the form of microplastics. The fate of these buoyant plastic fragments is a fundamental gap in our understanding of the fate and impact of plastics in marine ecosystems. To date, an effective sink for the lost microplastics has not been found. In this study, dissolved organic carbon (DOC) photo-production from the three dominant forms of ocean microplastics was assessed. These plastics were: 1) Polyethylene (PE) both for postconsumer samples and pure standard samples; 2) polypropylene (PP); and, expanded polystyrene (EPS). In addition, a Neustonic microplastic samples from the North Pacific Gyre were irradiated. These real-world samples were dominated by PE ( 80%). All samples were placed in seawater, in quartz flasks, and irradiated in a solar simulator for 2 months. During irradiation, DOC photo-production from PP, EPS, and the PE standard was exponential, while DOC photo-production from postconsumer PE and the Neustonic samples was linear. Scanning electron microscopy indicated surface ablation and micro-fragmentation during the irradiation of the three plastics that showed exponential DOC production (PP, EPS and standard PE), suggesting the increase in photo-reactivity of these plastics was a result of an increase in their surface to volume ratios and therefore their per-unit mass light exposure. Based on DOC production, the half-life of the microplastics ranged from 0.26 years for EPS to 86 years for PE, suggesting sunlight is a major removal term for buoyant oceanic microplastics. With respect to the broader carbon cycle, we conservatively estimate that plastic photodegradation releases 6 to 17 thousand metric tons of radiocarbon dead DOC to the surface ocean each year.

Moisture Durability with Vapor-Permeable Insulating Sheathing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lepage, R.; Lstiburek, J.

2013-09-01

Exterior sheathing insulation is an effective strategy in increasing the overall R-value of wall assemblies; other benefits include decreasing the effects of thermal bridging and increasing the moisture durability of the built assembly. Vapor-permeable exterior insulation, such as mineral board or expanded polystyrene foam, are one such product that may be used to achieve these benefits. However,uncertainty exists on the effects of inward driven moisture and the interaction of increased sheathing temperatures on the moisture durability of the edifice. To address these concerns, Building Science Corporation (BSC) conducted a series of hygrothermal models for cities representing a range of differentmore » climate zones. This report describes the research project, key research questions, and theprocedures utilized to analyse the problems.« less

Moisture Durability with Vapor-Permeable Insulating Sheathing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lepage, R.; Lstiburek, J.

2013-09-01

Exterior sheathing insulation is an effective strategy in increasing the overall R-value of wall assemblies; other benefits include decreasing the effects of thermal bridging and increasing the moisture durability of the built assembly. Vapor-permeable exterior insulation, such as mineral board or expanded polystyrene foam, are one such product that may be used to achieve these benefits. However, uncertainty exists on the effects of inward driven moisture and the interaction of increased sheathing temperatures on the moisture durability of the edifice. To address these concerns, Building Science Corporation (BSC) conducted a series of hygrothermal models for cities representing a range ofmore » different climate zones. This report describes the research project, key research questions, and the procedures utilized to analyse the problems.« less

Scalability of transport parameters with pore sizes in isodense disordered media

NASA Astrophysics Data System (ADS)

Reginald, S. William; Schmitt, V.; Vallée, R. A. L.

2014-09-01

We study light multiple scattering in complex disordered porous materials. High internal phase emulsion-based isodense polystyrene foams are designed. Two types of samples, exhibiting different pore size distributions, are investigated for different slab thicknesses varying from L = 1 \\text{mm} to 10 \\text{mm} . Optical measurements combining steady-state and time-resolved detection are used to characterize the photon transport parameters. Very interestingly, a clear scalability of the transport mean free path \\ellt with the average size of the pores S is observed, featuring a constant velocity of the transport energy in these isodense structures. This study strongly motivates further investigations into the limits of validity of this scalability as the scattering strength of the system increases.

Ecdysis period and rate deviations of dengue mosquito vector, Aedes aegypti reared in different artificial water-holding containers.

PubMed

Almanzor, Beatriz Louise J; Ho, Howell T; Carvajal, Thaddeus M

2016-03-01

Artificial water-holding containers (AWHCs) have been well-documented in many Aedes aegypti studies for dengue surveillance and developmental research. Hence, we investigated the role of different AHWCs on the development and ecdysis period of Ae. aegypti dengue vector, a container breeding mosquito. Nine types of AWHCs, namely glass, polystyrene foam, rubber, steel, porcelain, plastic, aluminum, clay and concrete, were chosen for the study. All AWHCs were subjected to the developmental assay for an observation period of 10 days. Regression and hazard analyses were employed to the developmental stages and the characteristics of the AWHCs. The observations revealed that Ae. aegypti development is fastest in glass and polystyrene containers while slowest in concrete containers. Moreover, pupal ecdysis appears to be the most affected by the characteristics of the AWHCs based on regression and hazard analyses. Characteristics of the container that can regulate water temperature seem to be the driving force with regards to the slow or fast development of Ae. aegypti, more notably in pupal ecdysis. The results of the study further strengthen our understanding on the dynamics of Ae. aegypti's developmental biology to different characteristics of artificial water containers. This, in turn, would aid in devising vector control strategies against dengue especially in endemic areas.

Characterisation of historic plastics using terahertz time-domain spectroscopy and pulsed imaging.

PubMed

Pastorelli, Gianluca; Trafela, Tanja; Taday, Phillip F; Portieri, Alessia; Lowe, David; Fukunaga, Kaori; Strlič, Matija

2012-05-01

Terahertz (THz) time-domain spectroscopy and 3D THz pulsed imaging have been explored with regard to polymer materials, both commodity and historic polymers. A systematic spectroscopic study of a wide range of different polymer materials showed significant differences in their spectra. Polyolefins and polystyrenes generally exhibit lower absorption than other examined polymers, various cellulose derivates, poly(vinyl chloride), poly(methyl methacrylate), polyamide, hard rubber and phenol formaldehyde resin, the last of these exhibiting the most intense absorption over the entire range, 0.15-4.2 THz. It was also examined how the presence of plasticisers in poly(vinyl chloride), the presence of fillers in polypropylene, and the degree of branching in polyethylene and polystyrene affect the spectra; inorganic fillers in polypropylene affected the absorption most. With 3D THz pulsed imaging, features in polymer objects were explored, appearing either as integral parts of the material (coatings and pores in foams) or as a consequence of physical deterioration (cracks, delamination). All of these features of various complexities can be successfully imaged in 3D. Terahertz technology is thus shown to have significant potential for both chemical and structural characterisation of polymers, which will be of interest to heritage science, but also to the polymer industry and development of analytical technologies in general.

Countability of Planck Boxes in Quantum Branching Models

NASA Astrophysics Data System (ADS)

Berezin, Alexander A.

2002-04-01

Two popular paradigms of cosmological quantum branching are Many World (MW) model of parallel universes (Everett, Deutsch) and inflationary quantum foam (IQF) model (Guth, Linde). Taking Planck L,T units as physically smallest, our Big Bang miniverse with size 10E28 cm and duration 10E18 sec has some 10E244 (N) elementary 4D Planck Boxes (PB) in its entire spacetime history. Using combinatorics, N! (about 10E10E247) is upper estimate for number of all possible 4D states, i.e. scale of "eternal return" (ER; Nietzsche, Eliade) for such miniverses. To count all states in full Megaverse (all up and down branches of infinite tree of all MW and/or IQF miniverses) we recall that all countable infinities have same (aleph-naught) cardinality (Cantor). Using Godel-type numbering, count PB in our miniverse by primes. This uses first N primes. Both MW and IQF models presume splitting of miniverses as springing (potentially) from each PB, making each PB infinitely rich, inexhaustible and unique. Next branching level is counted by integers p1Ep2, third level by p1Ep2Ep3 integers, etc, ad infinitum. To count in up and down directions from "our" miniverse, different branching subsets of powers of primes can be used at all levels of tower exponentiation. Thus, all PB in all infinitude of MW and/or IQF branches can be uniquely counted by never repeating integers (tower exponents of primes), offering escape from grim ER scenarios.

Microbicides and HIV: A Review and an update

PubMed Central

Naswa, Smriti; Marfatia, Y. S.; Prasad, T. L. N.

2012-01-01

HIV is a pandemic which has continually posed challenges to the scientific society in large and to medical fraternity in particular in terms of treatment as well as prevention. The treatment is lifelong suppressive than curative; hence the importance has always been to prevention strategies. The strategies like abstinence, monogamy and consistent condom use have various societal and behavioural issues and HIV vaccine is still not at the horizon. In such a scenario, pre-exposure prophylaxis (PrEP) and microbicides have emerged as newer options of prevention. Microbicides are referred to as topical PrEP. They are compounds that can be applied inside the vagina or rectum to protect against sexually transmitted infections (STIs) including HIV. Microbicides can be vaginal and rectal and can be formulated as gels, foams, rings, hydrogels, silicone elastomer gels, diaphragm, quick-dissolve polyvinyl alcohol based films, and bioadhesive vaginal tablets. The microbicides have been divided into various categories based on where they disrupt the pathway of sexual transmission of HIV. The article highlights the classes of microbicides and various trials conducted on them. It also enumerates various approaches in pipeline like antimicrobial peptides, aptamers, flavonoids, small interfering RNAs and DNAs, and bioengineered lactic acid bacilli. PMID:23188931

Progresses in Polystyrene Biodegradation and Prospects for Solutions to Plastic Waste Pollution

NASA Astrophysics Data System (ADS)

Yang, S. S.; Brandon, A. M.; Xing, D. F.; Yang, J.; Pang, J. W.; Criddle, C. S.; Ren, N. Q.; Wu, W. M.

2018-05-01

Petroleum-based plastic pollution has been a global environmental concern for decades. The obvious contrast between the remarkable durability of the plastics and their short service time leads to the increasing accumulation of plastic wastes in the environment. A cost-effective, sustainable strategy to solve the problem should focus on source control and clean up. Polystyrene (PS) wastes, a recalcitrant plastic polymer, are among the wide spread man-made plastic pollutants. Destruction of PS wastes can be achieved using various abiotic methods such as incineration but such methods release potential air pollution and generation of hazardous by-products. Biodegradation and bioremediation has been proposed for years. Since the 1970’s, the microbial biodegradation of plastics, including PS, has been evaluated with mixed and isolated cultures from different sources such as activated sludge, trash, soil, and manure. To date, PS biodegradation by these microbial cultures is still quite slow. Recently, the larvae of yellow mealworms (Tenebrio molitor Linnaeus) have demonstrated promising PS biodegradation performance. Mealworms have demonstrated the ability to chew and ingest PS foam as food and are capable of degrading and mineralizing PS into CO2 via microbe-dependent activities within the gut in less than the 12-15 hrs gut retention time. These research results have revealed a potential for microbial biodegradation and bioremediation of plastic pollutants.

A Novel Strategy for landslide displacement and its direction monitoring

NASA Astrophysics Data System (ADS)

Zhu, Z.-W.; Yuan, Q.-Y.; Liu, D.-Y.; Liu, B.; Liu, J.-C.; Luo, H.

2013-12-01

Landslide monitoring is important in predicting the behavior of landslides, thereby ensuring environmental, life, and property safety. On the basis of our previous studies, we conducted the double shear test by using a third-generation optical fiber transducer that uses expandable polystyrene (EPS) as base material. However, the third-generation transducer has poor performance when cohesive force is present between the grout and capillary stainless steel pipe of the transducer. Thus, the fourth-generation optical fiber transducer was invented. Similar to the third-generation transducer, the fourth-generation transducer also used EPS as its base material. Single shear test was conducted on the fourth-generation transducer after being grouted with cement mortar (1:1 mix ratio). The micro-bend loss mechanism of the optical fiber was considered, and the optical time domain reflectometry instrument was used. The fact that the loss sequence of optical fibers subjected to loading is different at various locations is found. The relationship of the loading-point displacement VS. optical fiber sliding distance and optical loss were measured. Results show that the maximum initial measurement precision of the newly proposed device is 1mm, the corresponding sliding distance is 21 mm, and the dynamic range is 0-20 mm. The fourth-generation transducer can measure the movement direction of loadings, thus making this transducer applicable for landslide monitoring.

New improvement of the combined optical fiber transducer for landslide monitoring

NASA Astrophysics Data System (ADS)

Zhu, Z.-W.; Yuan, Q.-Y.; Liu, D.-Y.; Liu, B.; Liu, J.-C.; Luo, H.

2014-08-01

Landslide monitoring is important in predicting the behavior of landslides, thereby ensuring environmental, life, and property safety. On the basis of our previous studies, we conducted the double shear test by using a third-generation optical fiber transducer that uses expandable polystyrene (EPS) as base material. However, the third-generation transducer has poor performance when cohesive force is present between the grout and capillary stainless steel pipe of the transducer. Thus, the fourth-generation optical fiber transducer was invented. Similar to the third-generation transducer, the fourth-generation transducer also used EPS as its base material. Single shear test was conducted on the fourth-generation transducer after being grouted with cement mortar (1 : 1 mix ratio). The micro-bend loss mechanism of the optical fiber was considered, and the optical time domain reflectometry instrument was used. The fact that the loss sequence of optical fibers subjected to loading is different at various locations is found. The relationship of the loading-point displacement vs. optical fiber sliding distance and optical loss were measured. Results show that the maximum initial measurement precision of the newly proposed device is 1 mm, the corresponding sliding distance is 21 mm, and the dynamic range is 0-20 mm. The fourth-generation transducer can measure the movement direction of loadings, thus making this transducer applicable for landslide monitoring.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Randolph, Randall Blaine; Oertel, John A.; Schmidt, Derek William

For this study, machined CH hemi-shell ablator capsules have been successfully produced by the MST-7 Target Fabrication Team at Los Alamos National Laboratory. Process development and micro-machining techniques have been developed to produce capsules for both the Omega and National Ignition Facility (NIF) campaigns. These capsules are gas filled up to 10 atm and consist of a machined plastic hemi-shell outer layer that accommodates various specially engineered low-density polystyrene foam cores. Machining and assembly of the two-part, step-jointed plastic hemi-shell outer layer required development of new techniques, processes, and tooling while still meeting very aggressive shot schedules for both campaigns.more » Finally, problems encountered and process improvements will be discussed that describe this very unique, complex capsule design approach through the first Omega proof-of-concept version to the larger NIF version.« less

Reusable and disposable cups: An energy-based evaluation

NASA Astrophysics Data System (ADS)

Hocking, Martin B.

1994-11-01

A group of five different types of reusable and disposable hot drink cups have been analyzed in detail with respect to their overall energy costs during fabrication and use. Electricity generating methods and efficiencies have been found to be key factors in the primary energy consumption for the washing of reusable cups and a less important factor in cup fabrication. In Canada or the United States, over 500 or more use cycles, reusable cups are found to have about the same or slightly more energy consumption, use for use, as moulded polystyrene foam cups used once and then discarded. For the same area paper cups used once and discarded are found to consume less fossil fuel energy per use than any of the other cup types examined. Details of this analysis, which could facilitate the comparative assessment of other scenarios, are presented.

Occurrences of organophosphorus esters and phthalates in the microplastics from the coastal beaches in north China.

PubMed

Zhang, Haibo; Zhou, Qian; Xie, Zhiyong; Zhou, Yang; Tu, Chen; Fu, Chuancheng; Mi, Wenying; Ebinghaus, Ralf; Christie, Peter; Luo, Yongming

2018-03-01

Chemical pollution in the microplastics has been concerned worldwide as pollutants might potentially transfer from the environment to living organisms via plastics. Here, we investigate organophosphorus esters (OPEs) and phthalic acid esters (PAEs) in the beached microplastics collected from 28 coastal beaches of the Bohai and Yellow Sea in north China. The analyzed microplastics included polyethylene (PE) pellets and fragments, polypropylene (PP) flakes and fragments and polystyrene (PS) foams. The tris-(2-chloroethyl)-phosphate (TCEP), tris (1-chloro-2-propyl) phosphate (TCPP) and di-(2-ethylhexyl) phthalate (DEHP) were the three predominant compounds found overall. The maximum Σ4 OPEs concentration was 84,595.9ngg -1 , almost three orders of magnitude higher than the maximum Σ9 PAEs concentration. The PP flakes and PS foams contained the highest concentrations of the additives in contrast to the PE pellets which contained the lowest. The high concentration level of carcinogenic chlorinated OPEs and DEHP with endocrine disrupting effects implied the suggested potential hazards to coastal organisms. Spatial differences and compositional variation of the additives among the different microplastics suggests different origins and residence times in the coastal environment. This indicates that the characteristics of chemical additives might be a useful approach when tracing sources of microplastics in the environment. Copyright © 2017 Elsevier B.V. All rights reserved.

Relative stability of tension band versus two-cortex screw fixation for treating fifth metatarsal base avulsion fractures.

PubMed

Husain, Z S; DeFronzo, D J

2000-01-01

This study assesses the strength of fixating avulsion fractures of the fifth metatarsal base with a 4.0-mm partially threaded cancellous screw crossing two cortices as compared to tension banding. Our data showed statistically significant fixation strength improvement over tension banding for avulsion fractures (p < 0.02) in both polystyrene foam models and fresh, nonpreserved frozen cadaveric samples. In cadavers, the screw fixations were able to withstand more than three times the load sustained by the tension band fixations. The study utilized the Instron 8500 tensiometer to apply physiologic loads to test the constructs until failure. The displacement and load data at failure show the limitations of both fixations. By increasing the load resistance while maintaining compression, the bicortical cancellous screw fixation created greater stability at the avulsion fracture of the fifth metatarsal base as compared to tension band stabilization.

Preprocessor with spline interpolation for converting stereolithography into cutter location source data

NASA Astrophysics Data System (ADS)

Nagata, Fusaomi; Okada, Yudai; Sakamoto, Tatsuhiko; Kusano, Takamasa; Habib, Maki K.; Watanabe, Keigo

2017-06-01

The authors have developed earlier an industrial machining robotic system for foamed polystyrene materials. The developed robotic CAM system provided a simple and effective interface without the need to use any robot language between operators and the machining robot. In this paper, a preprocessor for generating Cutter Location Source data (CLS data) from Stereolithography (STL data) is first proposed for robotic machining. The preprocessor enables to control the machining robot directly using STL data without using any commercially provided CAM system. The STL deals with a triangular representation for a curved surface geometry. The preprocessor allows machining robots to be controlled through a zigzag or spiral path directly calculated from STL data. Then, a smart spline interpolation method is proposed and implemented for smoothing coarse CLS data. The effectiveness and potential of the developed approaches are demonstrated through experiments on actual machining and interpolation.

Growing and testing mycelium bricks as building insulation materials

NASA Astrophysics Data System (ADS)

Xing, Yangang; Brewer, Matthew; El-Gharabawy, Hoda; Griffith, Gareth; Jones, Phil

2018-02-01

In order to improve energy performance of buildings, insulation materials (such as mineral glass and rock wools, or fossil fuel-based plastic foams) are being used in increasing quantities, which may lead to potential problem with materials depletions and landfill disposal. One sustainable solution suggested is the use of bio-based, biodegradable materials. A number of attempts have been made to develop biomaterials, such as sheep wood, hemcrete or recycled papers. In this paper, a novel type of bio insulation materials - mycelium is examined. The aim is to produce mycelium materials that could be used as insulations. The bio-based material was required to have properties that matched existing alternatives, such as expanded polystyrene, in terms of physical and mechanical characteristics but with an enhanced level of biodegradability. The testing data showed mycelium bricks exhibited good thermal performance. Future work is planned to improve growing process and thermal performance of the mycelium bricks.

Evaluation of adhesive and anti-adhesive properties of Pseudomonas aeruginosa biofilms and their inhibition by herbal plants

PubMed Central

Zameer, Farhan; MS, Rukmangada; Chauhan, Jyoti Bala; Khanum, Shaukath Ara; Kumar, Pramod; Devi, Aishwarya Tripurasundari; MN, Nagendra Prasad; BL, Dhananjaya

2016-01-01

Background and Objectives: Adhesion and colonization are prerequisites for the establishment of bacterial pathogenesis. The biofilm development of Pseudomonas aeruginosa was assessed on adhesive surfaces like dialysis membrane, stainless steel, glass and polystyrene. Materials and Methods: Microtiter plate biofilm assay was performed to assess the effect of nutrient medium and growth parameters of P. aeruginosa. Further, its growth on adhesive surfaces namely hydrophilic (dialysis membrane) and hydrophobic (polystyrene plate, square glass and stainless steel coupon) was assessed. The exopolysaccharide (EPS) was quantified using ruthenium red microplate assay and microscopic analysis was used to observe P. aeruginosa biofilm architecture. The anti-biofilm activity of herbal extracts on mature P. aeruginosa was performed. Results: The formation of large scale biofilms on dialysis membrane for 72 h was proved to be the best surface. In microscopic studies, very few exopolysaccaride fibrils, indicating a rather loose matrix was observed at 48 h. Further, thick exopolysaccaride, indicated higher adhesive properties at 72 h which is evident from ruthenium red staining. Among the plant extract used, Justicia wynaadensis leaf and Aristolochia indica (Eswari) root extract showed significant reduction of anti-biofilm activity of 0.178 OD and 0.192 OD in inhibiting mature biofilms at 0.225 OD respectively, suggesting the possible use of these extracts as efficient anti-adhesive and biofilm-disrupting agents with potential applications in controlling biofilms on surfaces. Conclusion: Our study facilitates better understanding in the development of P. aeruginosa biofilms on different food processing and clinical surfaces ultimately taking care of food safety and hygiene. PMID:27307976

Mixtures of latex particles and the surfactant of opposite charge used as interface stabilizers--influence of particle contact angle, zeta potential, flocculation and shear energy.

PubMed

Deleurence, Rémi; Parneix, Caroline; Monteux, Cécile

2014-09-28

We investigate the stabilization of air-water interfaces by mixtures of negatively charged latex particles (sulfate polystyrene) and cationic surfactants (alkyl trimethylammonium bromides). First we report results concerning the binding of surfactant molecules to the latex particles. As the surfactant concentration increases, the charge of the particles reverses, from negative to positive, because CnTAB first binds electrostatically to the latex particles and then through hydrophobic interaction with the monolayer already adsorbed on the particles as well as directly with the hydrophobic surface of the latex. Over a large range of surfactant concentrations around the charge inversion, a strong flocculation is observed and 100 μm large aggregates form in the suspension. Unlike previous studies published on mixtures of inorganic particles with oppositely charged surfactants, we show that we can vary the sign of the zeta potential of the particles without changing the contact angle of the particles over a large range of surfactant concentrations. Indeed, the latex particles that we study are more hydrophobic than inorganic particles, hence adding moderate concentrations of the surfactant results in a weak variation of the contact angle while the charge of the particles can be reversed. This enables decoupling of the effect of zeta potential and contact angle on the interfacial properties of the mixtures. Our study shows that the contact angle and the charge of the particles are not sufficient parameters to control the foam properties, and the key-parameters are the flocculation state and the shear energy applied to produce the foam. Indeed, flocculated samples, whatever the sign of the zeta potential, enable production of a stable armour at the interface. The large aggregates do not adsorb spontaneously at the interface because of their large size, however when a large shear energy is used to produce the foam very stable foam is obtained, where particles are trapped at interfaces. We suggest that the large aggregates may be broken during shear and may reform at the interface to form a solid armour. A simple calculation taking into account the adsorption dynamics of the aggregates as a function of their size is consistent with this hypothesis.

A new biodegradable sisal fiber-starch packing composite with nest structure.

PubMed

Xie, Qi; Li, Fangyi; Li, Jianfeng; Wang, Liming; Li, Yanle; Zhang, Chuanwei; Xu, Jie; Chen, Shuai

2018-06-01

A new completely biodegradable sisal fiber-starch packing composite was proposed. The effects of fiber content and alkaline treatment on the cushioning property of the composites were studied from energy absorption efficiency, cellular microstructure and compatibility between fiber and starch. With increasing fiber content, the nest structure of composites becomes dense first and then loosens, resulting in initial enhancement and subsequent weakening of the cushioning property of the composites. The composite with 4:13 mass ratio of fiber and thermoplastic starch (TPS) exhibit the optimal cushioning property. Alkaline treatment increases the compatibility between sisal fiber and TPS, promotes the formation of dense nest structure, thereby enhances the cushioning property of the composites. After biodegradability tests for 28 days, the weight loss of the composites was 62.36%. It's found that the composites are a promising replacement for expandable polystyrene (EPS) as packing material, especially under large compression load (0.7-6 MPa). Copyright © 2018 Elsevier Ltd. All rights reserved.

High-Throughput Cryopreservation of Plant Cell Cultures for Functional Genomics

PubMed Central

Ogawa, Yoichi; Sakurai, Nozomu; Oikawa, Akira; Kai, Kosuke; Morishita, Yoshihiko; Mori, Kumiko; Moriya, Kanami; Fujii, Fumiko; Aoki, Koh; Suzuki, Hideyuki; Ohta, Daisaku; Saito, Kazuki; Shibata, Daisuke

2012-01-01

Suspension-cultured cell lines from plant species are useful for genetic engineering. However, maintenance of these lines is laborious, involves routine subculturing and hampers wider use of transgenic lines, especially when many lines are required for a high-throughput functional genomics application. Cryopreservation of these lines may reduce the need for subculturing. Here, we established a simple protocol for cryopreservation of cell lines from five commonly used plant species, Arabidopsis thaliana, Daucus carota, Lotus japonicus, Nicotiana tabacum and Oryza sativa. The LSP solution (2 M glycerol, 0.4 M sucrose and 86.9 mM proline) protected cells from damage during freezing and was only mildly toxic to cells kept at room temperature for at least 2 h. More than 100 samples were processed for freezing simultaneously. Initially, we determined the conditions for cryopreservation using a programmable freezer; we then developed a modified simple protocol that did not require a programmable freezer. In the simple protocol, a thick expanded polystyrene (EPS) container containing the vials with the cell–LSP solution mixtures was kept at −30°C for 6 h to cool the cells slowly (pre-freezing); samples from the EPS containers were then plunged into liquid nitrogen before long-term storage. Transgenic Arabidopsis cells were subjected to cryopreservation, thawed and then re-grown in culture; transcriptome and metabolome analyses indicated that there was no significant difference in gene expression or metabolism between cryopreserved cells and control cells. The simplicity of the protocol will accelerate the pace of research in functional plant genomics. PMID:22437846

Plastic in surface waters of the Inside Passage and beaches of the Salish Sea in Washington State.

PubMed

Davis, Wallace; Murphy, Anne G

2015-08-15

We summarize results of two independent studies on plastic pollution in the marine environment that overlap in time and space. One study evaluated the abundance of anthropogenic debris on 37 sandy beaches bordering the Salish Sea in Washington State while the other characterized plastic debris in surface waters of the Salish Sea and the Inside Passage to Skagway, Alaska. Both studies concluded that foam, primarily expanded polystyrene was the dominant pollutant. Plastic was found in surface waters the full length of the Inside Passage but was concentrated near harbors. At the wrack line, an average square meter of Washington's 1180km of sandy beaches in the Salish Sea had 61 pieces of anthropogenic debris weighing approximately 5g. The total loading for the entire 1m wide band is estimated to be 72,000,000 pieces and 5.8metric tons. Most anthropogenic debris on beaches is generated within the region. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterization of supersonic radiation diffusion waves

DOE PAGES

Moore, Alastair S.; Guymer, Thomas M.; Morton, John; ...

2015-02-27

Supersonic and diffusive radiation flow is an important test problem for the radiative transfer models used in radiation-hydrodynamics computer codes owing to solutions being accessible via analytic and numeric methods. We present experimental results with which we compare these solutions by studying supersonic and diffusive flow in the laboratory. Here, we present results of higher-accuracy experiments than previously possible studying radiation flow through up to 7 high-temperature mean free paths of low-density, chlorine-doped polystyrene foam and silicon dioxide aerogel contained by an Au tube. Measurements of the heat front position and absolute measurements of the x-ray emission arrival at themore » end of the tube are used to test numerical and analytical models. We find excellent absolute agreement with simulations provided that the opacity and the equation of state are adjusted within expected uncertainties; analytical models provide a good phenomenological match to measurements but are not in quantitative agreement due to their limited scope.« less

The Importance of Take-Out Food Packaging Attributes: Conjoint Analysis and Quality Function Deployment Approach

NASA Astrophysics Data System (ADS)

Lestari Widaningrum, Dyah

2014-03-01

This research aims to investigate the importance of take-out food packaging attributes, using conjoint analysis and QFD approach among consumers of take-out food products in Jakarta, Indonesia. The conjoint results indicate that perception about packaging material (such as paper, plastic, and polystyrene foam) plays the most important role overall in consumer perception. The clustering results that there is strong segmentation in which take-out food packaging material consumer consider most important. Some consumers are mostly oriented toward the colour of packaging, while another segment of customers concerns on packaging shape and packaging information. Segmentation variables based on packaging response can provide very useful information to maximize image of products through the package's impact. The results of House of Quality development described that Conjoint Analysis - QFD is a useful combination of the two methodologies in product development, market segmentation, and the trade off between customers' requirements in the early stages of HOQ process

The plastic-associated microorganisms of the North Pacific Gyre.

PubMed

Carson, Henry S; Nerheim, Magnus S; Carroll, Katherine A; Eriksen, Marcus

2013-10-15

Microorganisms likely mediate processes affecting the fate and impacts of marine plastic pollution, including degradation, chemical adsorption, and colonization or ingestion by macroorganisms. We investigated the relationship between plastic-associated microorganism communities and factors such as location, temperature, salinity, plankton abundance, plastic concentration, item size, surface roughness, and polymer type. Small plastic items from the surface of the North Pacific Gyre in 2011 were examined using scanning electron microscopy. Bacillus bacteria (mean 1664 ± 247 individuals mm(-2)) and pennate diatoms (1097 ± 154 mm(-2)) were most abundant, with coccoid bacteria, centric diatoms, dinoflagellates, coccolithophores, and radiolarians present. Bacterial abundance was patchy, but increased on foamed polystyrene. Diatom abundance increased on items with rough surfaces and at sites with high plastic concentrations. Morphotype richness increased slightly on larger fragments, and a biogeographic transition occurred between pennate diatom groups. Better characterizing this community will aid in understanding how it interacts with plastic pollution. Copyright © 2013 Elsevier Ltd. All rights reserved.

Accelerating materials discovery through the development of polymer databases

NASA Astrophysics Data System (ADS)

Audus, Debra

In our line of business we create chemical solutions for a wide range of applications, such as home and personal care, printing and packaging, automotive and structural coatings, and structural plastics and foams applications. In this environment, stable and highly automated workflows suitable to handle complex systems are a must. By satisfying these prerequisites, efficiency for the development of new materials can be significantly improved by combining modeling and experimental approaches. This is in fact in line with recent Materials Genome Initiative efforts sponsored by the US administration. From our experience, we know, that valuable contributions to product development are possible today by combining existing modeling techniques in an intelligent fashion, provided modeling and experiment work closely together. In my presentation I intend to review approaches to build and parameterize soft matter systems. As an example of our standard workflow, I will show a few applications, which include the design of a stabilizer molecule for dispersing polymer particles and the simulation of polystyrene dispersions.

Characterization of supersonic radiation diffusion waves

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, Alastair S.; Guymer, Thomas M.; Morton, John

Supersonic and diffusive radiation flow is an important test problem for the radiative transfer models used in radiation-hydrodynamics computer codes owing to solutions being accessible via analytic and numeric methods. We present experimental results with which we compare these solutions by studying supersonic and diffusive flow in the laboratory. Here, we present results of higher-accuracy experiments than previously possible studying radiation flow through up to 7 high-temperature mean free paths of low-density, chlorine-doped polystyrene foam and silicon dioxide aerogel contained by an Au tube. Measurements of the heat front position and absolute measurements of the x-ray emission arrival at themore » end of the tube are used to test numerical and analytical models. We find excellent absolute agreement with simulations provided that the opacity and the equation of state are adjusted within expected uncertainties; analytical models provide a good phenomenological match to measurements but are not in quantitative agreement due to their limited scope.« less

Blueschists and eclogites from southern Sifnos (Cyclades, Greece)

NASA Astrophysics Data System (ADS)

Weil, Jonas; Petrakakis, Konstantin; Grasemann, Bernhard; Iglseder, Christoph

2010-05-01

Eclogite/blueschist facies rocks from northern Sifnos (Cyclades) are well known and have been described by many authors. A small occurrence of similar rocks in the south-west of Sifnos has been investigated and is compared to other occurrences in terms of their mineral assemblages, chemistry, petrography and structural position. The tectono-metamorphic evolution on Sifnos is characterized by a regional blueschist / eclogite facies metamorphism (M1) during the Eocene, followed by a regional Oligo-Miocene medium pressure overprint (M2). The investigated rocks from the Fikiada Bay area formed during M1 but were overprinted by a brittle / ductile M2 event. The high-pressure rock assemblage of Fikiada bay represents a sequence of metabasites, metaacidites, and metasediments with a foliation-parallel compositional layering. Rootless isoclinal folding of the regional foliation is common with fold axes trending roughly NW-SE; hinges are overprinted by later axial foliation planes. The foliation is well developed and mostly dips to N to E, the main pervasive stretching lineation is shallow and plunging to NE. Grt- rich dark blueschists, bearing eclogite-boudins of some dm size, alternate with lighter Qtz-rich Grt-bearing, cm to m thick layers. Massive, very coarse grained Ep+Chl+Ab -rich gneisses form layers with up to 3 m thickness. Metasediments comprise light Cal-rich gneisses as well as metapelites and quartzites. These lithologies are overlain by highly strained calcite marbles bearing boudins of Dol-marble. Foliation, stretching lineation and isoclinal folds show the same orientation as in the silicates. The blueschists show the characteristic assemblage Gln + Grt + Ep + Ab + Phg + Pg +Qtz (+Cal) + Mag. Inclusions in large poikiloblastic Grt reveal an earlier compositional layering: Domains with conserved foam microstructures of Qtz and domains of massive Grt including relics of Jd (XNa = 0.9), Ctd, Ep, Rt and Mag. Gln shows a zonal pattern with Mg-rich cores to ferro-glaucophane and crossite- richer rims. Ep is zoned too with decreasing Fe from core to rim, while Grt-poikiloblasts are nearly homogeneous in composition. Eclogitic assemblages consist of Grt + Omp + Ep + Phg + Gln ± Qtz. A greenschist-facies overprint accompanied by Fe- and CO2- rich fluids is mostly evident along shear bands of variable thickness from thin section to outcrop scale. It is best documented by the growth of syntectonic Ab+Chl neoblasts. Metabasite layers intercalated with the marble show a pervasive greenschist-facies overprint with extensive, neoblastic growth of Chl an Ab. Early Ep remains unaffected, but Gln and Grt are preserved only as relics. Petrography and mineral chemistry of southern Sifnos HP-rocks comply with the occurrence in northern Sifnos (e.g. comprehensive description by Schliestedt 1986) References: Schliestedt, M., 1986. Eclogite-blueschist relationships as evidenced by mineral equilibria in the high-pressure rocks of Sifnos (Cycladic islands), Greece. Journal of Petrology, 27,1437-1459 Mineral abbreviations after Kretz, 1983: Symbols for rock-forming minerals. American Mineralogist, 68, 277-279

Influence of Proportion and Size of Sugarcane Bagasse Fiber on the Properties of Sweet Potato Starch Foams

NASA Astrophysics Data System (ADS)

Cruz-Tirado, J. P.; Tapia-Blácido, Delia R.; Siche, Raúl

2017-08-01

The objective of this work was the proportion and size of cane bagasse fiber in the physical (density and thickness), mechanical (flexural strength and tensile at break) and thermal (TG and DTG) properties of trays made from sweet potato starch. A fiber size of 75-45 µm and a 2.5% ratio allowed to obtain trays with low thicknesses and densities, but with more compact structures that improved the mechanical properties of trays made from sweet potato starch alone. In addition, higher thermal stability and lower decomposition rate are shown for trays with fiber size 75-45 µm and ratios of 2.5% and 5%. These results show that the smaller fiber size improves the properties of the sweet potato starch trays and that these trays can be used to replace the expanded polymer (EPS) for use in dry foods.

Energy Saving Melting and Revert Reduction (E-SMARRT): Precision Casting of Steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. Von L. Richards

2011-09-30

This project addresses improvements in metal casting processes by reducing scrap and reducing the cost of production, due to scrap reduction from investment casting and yield improvement offered by lost foam casting as compared to no-bake or green sand molding. The objectives for the investment casting portion of the subtask are to improve knowledge of fracture toughness of mold shells and the sources of strength limiting flaws and to understand the effects of wax reclamation procedures on wax properties. Applying 'clean steel' approaches to pouring technology and cleanliness in investment casting of steel are anticipated to improve incoming materials inspectionmore » procedures as they affect the microstructure and toughness of the shell. This project focused on two areas of study in the production of steel castings to reduce scrap and save energy: (1) Reducing the amount of shell cracking in investment cast steel production; (2) Investigate the potential of lost foam steel casting The basic findings regarding investment casting shell cracking were: (1) In the case of post pouring cracking, this could be related to phase changes in silica upon cooling and could be delayed by pouring arrangement strategies that maintained the shell surface at temperature for longer time. Employing this delay resulted in less adherent oxidation of castings since the casting was cooler at the time o fair exposure. (2) A model for heat transfer through water saturated shell materials under steam pressure was developed. (3) Initial modeling result of autoclave de-waxing indicated the higher pressure and temperature in the autoclave would impose a steeper temperature gradient on the wax pattern, causing some melt flow prior to bulk expansion and decreasing the stress on the green shell. Basic findings regarding lost foam casting of steel at atmospheric pressure: (1) EPS foam generally decomposes by the collapse mode in steel casting. (2) There is an accumulation of carbon pick-up at the end of the casting opposite the gate. (3) It is recommended that lost foam castings in steel be gated for a quiescent fill in an empty cavity mold to prevent foam occlusion defects from the collapse mode. The energy benefit is primarily in yield savings and lower casting weight per function due to elimination of draft and parting lines for the larger lost foam castings. For the smaller investment casting, scrap losses due to shell cracking will be reduced. Both of these effects will reduce the metal melted per good ton of castings. There will also be less machine stock required per casting which is a yield savings and a small additional energy savings in machining. Downstream savings will come from heavy truck and railroad applications. Application of these processes to heavy truck castings will lighten the heavy truck fleet by about ten pounds per truck. Using ten years to achieve full penetration of the truck fleet at linear rate this will result in a fuel savings of 131 trillion BTU over ten years.« less

21 CFR 177.1640 - Polystyrene and rubber-modified polystyrene.

Code of Federal Regulations, 2011 CFR

2011-04-01

... polystyrene and rubber-modified polystyrene used in food-packaging adhesives complying with § 175.105 of this... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Polystyrene and rubber-modified polystyrene. 177.1640 Section 177.1640 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 177.1640 - Polystyrene and rubber-modified polystyrene.

Code of Federal Regulations, 2010 CFR

2010-04-01

... polystyrene and rubber-modified polystyrene used in food-packaging adhesives complying with § 175.105 of this... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polystyrene and rubber-modified polystyrene. 177.1640 Section 177.1640 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 177.1640 - Polystyrene and rubber-modified polystyrene.

Code of Federal Regulations, 2013 CFR

2013-04-01

... polystyrene and rubber-modified polystyrene used in food-packaging adhesives complying with § 175.105 of this... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Polystyrene and rubber-modified polystyrene. 177.1640 Section 177.1640 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 177.1640 - Polystyrene and rubber-modified polystyrene.

Code of Federal Regulations, 2012 CFR

2012-04-01

... polystyrene and rubber-modified polystyrene used in food-packaging adhesives complying with § 175.105 of this... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Polystyrene and rubber-modified polystyrene. 177.1640 Section 177.1640 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

An overview of hexabromocyclododecane (HBCDs) in environmental media with focus on their potential risk and management in China.

PubMed

Cao, Xianghui; Lu, Yonglong; Zhang, Yueqing; Khan, Kifayatullah; Wang, Chenchen; Baninla, Yvette

2018-05-01

Hexabromocyclododecanes (HBCDs) are the subject of recent interest and potential risk assessment particularly in China due to its ubiquitous existence in a variety of environmental media. This paper reviews the recent studies conducted on HBCDs in different environmental media (air, soil, water, river sediment, sewage sludge, biota and daily food) in China. At the same time, human health risks via food and occupational exposure of HBCDs in production plants, expanded polystyrene (EPS) and extruded polystyrene (XPS) plants were assessed. The review reveals that HBCDs levels of air, soil, sediment, sewage sludge, biota and food presented a geographical variation in the eastern coastal regions of China. There were many factors resulting in the variation, such as sampling sites, climate and analytical method. In terms of diastereoisomer, α-HBCD and γ-HBCD were the predominant diastereoisomers in air, soil, sediment, and sewage sludge. In the water, α-HBCD and γ-HBCD shared the major proportion to the total HBCDs. However, only α-HBCD was the predominant diastereoisomer in biota. With regard to human exposure pathway to HBCDs, food was the major route for human exposure to HBCDs, especially meat. In addition, soil and road dust were also important exposure pathways. Furthermore, workers and residents, especially infants in and around waste dumping sites and industrial areas are exposed to the highest HBCDs levels among all the populations studied thus far. HBCDs posed a potential threat to the environment and human health. Therefore, risk assessment and management have an important role to play in preventing and mitigating HBCDs risks. Copyright © 2018 Elsevier Ltd. All rights reserved.

Interfacial rheology of model particles at liquid interfaces and its relation to (bicontinuous) Pickering emulsions

NASA Astrophysics Data System (ADS)

Thijssen, J. H. J.; Vermant, J.

2018-01-01

Interface-dominated materials are commonly encountered in both science and technology, and typical examples include foams and emulsions. Conventionally stabilised by surfactants, emulsions can also be stabilised by micron-sized particles. These so-called Pickering-Ramsden (PR) emulsions have received substantial interest, as they are model arrested systems, rather ubiquitous in industry and promising templates for advanced materials. The mechanical properties of the particle-laden liquid-liquid interface, probed via interfacial rheology, have been shown to play an important role in the formation and stability of PR emulsions. However, the morphological processes which control the formation of emulsions and foams in mixing devices, such as deformation, break-up, and coalescence, are complex and diverse, making it difficult to identify the precise role of the interfacial rheological properties. Interestingly, the role of interfacial rheology in the stability of bicontinuous PR emulsions (bijels) has been virtually unexplored, even though the phase separation process which leads to the formation of these systems is relatively simple and the interfacial deformation processes can be better conceptualised. Hence, the aims of this topical review are twofold. First, we review the existing literature on the interfacial rheology of particle-laden liquid interfaces in rheometrical flows, focussing mainly on model latex suspensions consisting of polystyrene particles carrying sulfate groups, which have been most extensively studied to date. The goal of this part of the review is to identify the generic features of the rheology of such systems. Secondly, we will discuss the relevance of these results to the formation and stability of PR emulsions and bijels.

Direct-drive inertial confinement fusion research at the Laboratory for Laser Energetics: charting the path to thermonuclear ignition

NASA Astrophysics Data System (ADS)

McCrory, R. L.; Regan, S. P.; Loucks, S. J.; Meyerhofer, D. D.; Skupsky, S.; Betti, R.; Boehly, T. R.; Craxton, R. S.; Collins, T. J. B.; Delettrez, J. A.; Edgell, D.; Epstein, R.; Fletcher, K. A.; Freeman, C.; Frenje, J. A.; Glebov, V. Yu.; Goncharov, V. N.; Harding, D. R.; Igumenshchev, I. V.; Keck, R. L.; Kilkenny, J. D.; Knauer, J. P.; Li, C. K.; Marciante, J.; Marozas, J. A.; Marshall, F. J.; Maximov, A. V.; McKenty, P. W.; Myatt, J.; Padalino, S.; Petrasso, R. D.; Radha, P. B.; Sangster, T. C.; Séguin, F. H.; Seka, W.; Smalyuk, V. A.; Soures, J. M.; Stoeckl, C.; Yaakobi, B.; Zuegel, J. D.

2005-10-01

Significant theoretical and experimental progress continues to be made at the University of Rochester's Laboratory for Laser Energetics (LLE), charting the path to direct-drive inertial confinement fusion (ICF) ignition. Direct drive offers the potential for higher-gain implosions than x-ray drive and is a leading candidate for an inertial fusion energy power plant. LLE's direct-drive ICF ignition target designs for the National Ignition Facility (NIF) are based on hot-spot ignition. A cryogenic target with a spherical DT-ice layer, within or without a foam matrix, enclosed by a thin plastic shell, will be directly irradiated with ~1.5 MJ of laser energy. Cryogenic and plastic/foam (surrogate-cryogenic) targets that are hydrodynamically scaled from these ignition target designs are imploded on the 60-beam, 30 kJ, UV OMEGA laser system to validate the key target physics issues, including energy coupling, hydrodynamic instabilities and implosion symmetry. Prospects for direct-drive ignition on the NIF are extremely favourable, even while it is in its x-ray-drive irradiation configuration, with the development of the polar-direct-drive concept. A high-energy petawatt capability is being constructed at LLE next to the existing 60-beam OMEGA compression facility. This OMEGA EP (extended performance) laser will add two short-pulse, 2.6 kJ beams to the OMEGA laser system to backlight direct-drive ICF implosions and study fast-ignition physics with focused intensities up to 6 × 1020 W cm-2.

Nonlinear deformation and localized failure of bacterial streamers in creeping flows

PubMed Central

Biswas, Ishita; Ghosh, Ranajay; Sadrzadeh, Mohtada; Kumar, Aloke

2016-01-01

We investigate the failure of bacterial floc mediated streamers in a microfluidic device in a creeping flow regime using both experimental observations and analytical modeling. The quantification of streamer deformation and failure behavior is possible due to the use of 200 nm fluorescent polystyrene beads which firmly embed in the extracellular polymeric substance (EPS) and act as tracers. The streamers, which form soon after the commencement of flow begin to deviate from an apparently quiescent fully formed state in spite of steady background flow and limited mass accretion indicating significant mechanical nonlinearity. This nonlinear behavior shows distinct phases of deformation with mutually different characteristic times and comes to an end with a distinct localized failure of the streamer far from the walls. We investigate this deformation and failure behavior for two separate bacterial strains and develop a simplified but nonlinear analytical model describing the experimentally observed instability phenomena assuming a necking route to instability. Our model leads to a power law relation between the critical strain at failure and the fluid velocity scale exhibiting excellent qualitative and quantitative agreeing with the experimental rupture behavior. PMID:27558511

Antifungal Effects of Saponin Extract from Rhizomes of Dioscorea panthaica Prain et Burk against Candida albicans

PubMed Central

Zhuang, Xinming; Feng, Xuechao

2018-01-01

Candida albicans is the most common fungal pathogen causing serious diseases, while there are only a paucity of antifungal drugs. Therefore, the present study was performed to investigate the antifungal effects of saponin extract from rhizomes of Dioscorea panthaica Prain et Burk (Huangshanyao Saponin extract, HSE) against C. albicans. HSE inhibits the planktonic growth and biofilm formation and development of C. albicans. 16–64 μg/mL of HSE could inhibit adhesion to polystyrene surfaces, transition from yeast to filamentous growth, and production of secreted phospholipase and could also induce endogenous reactive oxygen species (ROS) production and disrupt cell membrane in planktonic cells. Inhibitory activities against extracellular exopolysaccharide (EPS) production and ROS production in preformed biofilms could be inhibited by 64–256 μg/mL of HSE. Cytotoxicity against human Chang's liver cells is low, with a half maximal inhibitory concentration (IC50) of about 256 μg/mL. In sum, our study suggested that HSE might be used as a potential antifungal therapeutic against C. albicans. PMID:29853962

Construction material

DOEpatents

Wagh, Arun S [Orland Park, IL; Antink, Allison L [Bolingbrook, IL

2008-07-22

A structural material of a polystyrene base and the reaction product of the polystyrene base and a solid phosphate ceramic is applied as a slurry which includes one or more of a metal oxide or a metal hydroxide with a source of phosphate to produce a phosphate ceramic and a poly (acrylic acid or acrylate) or combinations or salts thereof and polystyrene or MgO applied to the polystyrene base and allowed to cure so that the dried aqueous slurry chemically bonds to the polystyrene base. A method is also disclosed of applying the slurry to the polystyrene base.

Plastic debris in the coastal environment: The invincible threat? Abundance of buried plastic debris on Malaysian beaches.

PubMed

Fauziah, S H; Liyana, I A; Agamuthu, P

2015-09-01

Studies on marine debris have gained worldwide attention since many types of debris have found their way into the food chain of higher organisms. Thus, it is crucial that more focus is given to this area in order to curb contaminations in sea food. This study was conducted to quantify plastic debris buried in sand at selected beaches in Malaysia. Marine debris was identified according to size range and distribution, and this information was related to preventive actions to improve marine waste issues. For the purpose of this study, comparison of plastic waste abundance between a recreational beach and fish-landing beaches was also carried out, since the different beach types represent different activities that produce debris. Six beaches along the Malaysian coastline were selected for this study. The plastic types in this study were related to the functions of the beach. While recreational beaches have abundant quantities of plastic film, foamed plastic including polystyrene, and plastic fragment, fish-landing beaches accumulated line and foamed plastic. A total of 2542 pieces (265.30 g m(-2)) of small plastic debris were collected from all six beaches, with the highest number from Kuala Terengganu, at 879 items m(-2) on Seberang Takir Beach, followed by Batu Burok Beach with 780 items m(-2). Findings from studies of Malaysian beaches have provided a clearer understanding of the distribution of plastic debris. This demonstrates that commitments and actions, such as practices of the 'reduce, reuse, recycle' (3R) approach, supporting public awareness programmes and beach clean-up activities, are essential in order to reduce and prevent plastic debris pollution. © The Author(s) 2015.

Size distribution of stranded small plastic debris on the coast of Guangdong, South China.

PubMed

Fok, Lincoln; Cheung, Pui Kwan; Tang, Guangda; Li, Wai Chin

2017-01-01

Beach environments are known to be conducive to fragmentation of plastic debris, and highly fragmented plastic particles can interact with smaller organisms. Even through stranded plastic debris may not interact directly with marine organisms, backwash processes may transport this debris back to coastal waters, where it may affect a wide range of marine life at different trophic levels. This study analysed the size distribution of stranded plastic debris (<10 mm) collected from eight coastal beaches in Guangdong Province, China. Polystyrene (PS) foams and fragments smaller than 7 mm were increasingly abundant in the smaller size classes, whereas resin pellets remained in their production sizes (∼3 mm). Microplastics (<5 mm) accounted for over 98% of the total plastic debris by abundance and 71% by weight, indicating that the plastic debris on these coastal beaches was highly fragmented and the majority of the plastic masses belonged to the microplastic size range. The observed size distributions of PS foams and fragments are believed to result from continued fragmentation. Previous studies found that the residence time of beached debris was less than one year on average, and no sign of plastic accumulation with depth in beach sediment was observed. Therefore, coastal beaches may represent a reservoir of highly fragmented and degraded microplastics that may be mobilised and returned to the sea during storm events. Further research on the dynamics and longevity of microplastics on beaches will help reveal the mass balance of microplastics on the shoreline and determine whether shorelines are sinks or sources of microplastics. Copyright © 2016 Elsevier Ltd. All rights reserved.

Application of the Finite Elemental Analysis to Modeling Temperature Change of the Vaccine in an Insulated Packaging Container during Transport.

PubMed

Ge, Changfeng; Cheng, Yujie; Shen, Yan

2013-01-01

This study demonstrated an attempt to predict temperatures of a perishable product such as vaccine inside an insulated packaging container during transport through finite element analysis (FEA) modeling. In order to use the standard FEA software for simulation, an equivalent heat conduction coefficient is proposed and calculated to describe the heat transfer of the air trapped inside the insulated packaging container. The three-dimensional, insulated packaging container is regarded as a combination of six panels, and the heat flow at each side panel is a one-dimension diffusion process. The transit-thermal analysis was applied to simulate the heat transition process from ambient environment to inside the container. Field measurements were carried out to collect the temperature during transport, and the collected data were compared to the FEA simulation results. Insulated packaging containers are used to transport temperature-sensitive products such as vaccine and other pharmaceutical products. The container is usually made of an extruded polystyrene foam filled with gel packs. World Health Organization guidelines recommend that all vaccines except oral polio vaccine be distributed in an environment where the temperature ranges between +2 to +8 °C. The primary areas of concern in designing the packaging for vaccine are how much of the foam thickness and gel packs should be used in order to keep the temperature in a desired range, and how to prevent the vaccine from exposure to freezing temperatures. This study uses numerical simulation to predict temperature change within an insulated packaging container in vaccine cold chain. It is our hope that this simulation will provide the vaccine industries with an alternative engineering tool to validate vaccine packaging and project thermal equilibrium within the insulated packaging container.

Construction Material And Method

DOEpatents

Wagh, Arun S.; Antink, Allison L.

2006-02-21

A structural material of a polystyrene base and the reaction product of the polystyrene base and a solid phosphate ceramic. The ceramic is applied as a slurry which includes one or more of a metal oxide or a metal hydroxide with a source of phosphate to produce a phosphate ceramic and a poly (acrylic acid or acrylate) or combinations or salts thereof and polystyrene or MgO applied to the polystyrene base and allowed to cure so that the dried aqueous slurry chemically bonds to the polystyrene base. A method is also disclosed of applying the slurry to the polystyrene base.

Method of binding structural material

DOEpatents

Wagh, Arun S.; Antink, Allison L.

2007-12-25

A structural material of a polystyrene base and the reaction product of the polystyrene base and a solid phosphate ceramic. The ceramic is applied as a slurry which includes one or more of a metal oxide or a metal hydroxide with a source of phosphate to produce a phosphate ceramic and a poly (acrylic acid or acrylate) or combinations or salts thereof and polystyrene or MgO applied to the polystyrene base and allowed to cure so that the dried aqueous slurry chemically bonds to the polystyrene base. A method is also disclosed of applying the slurry to the polystyrene base.

Supersonic, shockwave-driven hydrodynamic instability experiments at OMEGA-EP

NASA Astrophysics Data System (ADS)

Wan, Willow

2016-10-01

Hydrodynamic instabilities play a dominant role in the transport of mass, momentum, and energy in nearly every plasma environment, governing the dynamics of natural and engineering systems such as solar convective zones, magnetospheric boundaries, and fusion experiments. In past decades, limitations in our understanding of hydrodynamic instabilities have led to discrepancies between observations and predictions. Since then, significant improvements have been made to our available experimental techniques, diagnostics, and simulation capabilities. Here, we present a novel experimental platform that can sustain a steady, supersonic flow across a precision-machined, well-characterized material interface for unprecedented durations We applied this platform to a series of Kelvin-Helmholtz instability experiments. The Kelvin-Helmholtz instability generates vortical structures and turbulence at an interface with shear flow. In a supersonic flow, the growth rate is inhibited and the instability structure is altered. The data were obtained at the OMEGA-EP facility by firing three laser beams in sequence to produce a 12 kJ, 28 ns stitched laser pulse. The ablation pressure sustained a steady shockwave for 70 ns over a foam-plastic, single-mode or dual-mode interface. A spherical crystal imager was used to measure the evolution of these modulations with high-resolution x-ray radiography using Cu Kα radiation at 8.0 keV. The observed structure was reproduced with 2D hydrodynamic simulations. Supported by the U.S. DOE, through NNSA Grants DE-NA0002956 (SSAA) and DE-NA0002719 (NLUF), by the LLE under DE-NA0001944, and by the LLNL under subcontract B614207 to DE-AC52-07NA27344.

The surface pressure dynamics and appearance of mixed monolayers of cholesterol and different sized polystyrenes at an air-water interface.

PubMed

Mudgil, Poonam; Dennis, Gary R; Millar, Thomas J

2005-02-15

Synthetic polymers are increasingly being used in situations where they are designed to interact with biological systems. As a result, it is important to investigate the interactions of the polymers with biochemicals. We have used cholesterol, as an example of an important biological surfactant component, to study its interactions with polystyrene. Mixed monolayers of cholesterol and one of two different molecular weight polystyrenes were formed at an air-water interface to investigate their interactions and to determine whether the size of the polystyrene affected the interaction. The pressure-area (pi-A) isocycles of mixed monolayers of cholesterol and polystyrene MW 2700 or polystyrene MW32700 showed that strongest attractive interactions occur at high surface pressures and in polystyrene rich films. The excess area and excess free energy of mixing were most negative at high surface pressures and at high mole fraction of polystyrene. The most stable mixed monolayers were formed with X(PS2700) = 0.9 and X(PS32700) = 0.09. Microscopic observation of the mixed monolayers of cholesterol and polystyrene showed the formation of stable islands in the cholesterol/polystyrene mixtures. These observations, the nature of the inflection points in the isocycles, and the anomalous changes in free energy lead us to conclude that there is a stable rearrangement of polystyrene into compact islands when it is mixed with cholesterol. Any excess cholesterol is excluded from these islands and remains as a separate film surrounding the islands.

Simulations of Converging Shock Collisions for Shock Ignition

NASA Astrophysics Data System (ADS)

Sauppe, Joshua; Dodd, Evan; Loomis, Eric

2016-10-01

Shock ignition (SI) has been proposed as an alternative to achieving high gain in inertial confinement fusion (ICF) targets. A central hot spot below the ignition threshold is created by an initial compression pulse, and a second laser pulse drives a strong converging shock into the fuel. The collision between the rebounding shock from the compression pulse and the converging shock results in amplification of the converging shock and increases the hot spot pressure above the ignition threshold. We investigate shock collision in SI drive schemes for cylindrical targets with a polystyrene foam interior using radiation-hydrodynamics simulations with the RAGE code. The configuration is similar to previous targets fielded on the Omega laser. The CH interior results in a lower convergence ratio and the cylindrical geometry facilitates visualization of the shock transit using an axial X-ray backlighter, both of which are important for comparison to potential experimental measurements. One-dimensional simulations are used to determine shock timing, and the effects of low mode asymmetries in 2D computations are also quantified. LA-UR-16-24773.

NDE application of ultrasonic tomography to a full-scale concrete structure.

PubMed

Choi, Hajin; Popovics, John S

2015-06-01

Newly developed ultrasonic imaging technology for large concrete elements, based on tomographic reconstruction, is presented. The developed 3-D internal images (velocity tomograms) are used to detect internal defects (polystyrene foam and pre-cracked concrete prisms) that represent structural damage within a large steel reinforced concrete element. A hybrid air-coupled/contact transducer system is deployed. Electrostatic air-coupled transducers are used to generate ultrasonic energy and contact accelerometers are attached on the opposing side of the concrete element to detect the ultrasonic pulses. The developed hybrid testing setup enables collection of a large amount of high-quality, through-thickness ultrasonic data without surface preparation to the concrete. The algebraic reconstruction technique is used to reconstruct p-wave velocity tomograms from the obtained time signal data. A comparison with a one-sided ultrasonic imaging method is presented for the same specimen. Through-thickness tomography shows some benefit over one-sided imaging for highly reinforced concrete elements. The results demonstrate that the proposed through-thickness ultrasonic technique shows great potential for evaluation of full-scale concrete structures in the field.

Cell directional migration and oriented division on three-dimensional laser-induced periodic surface structures on polystyrene.

PubMed

Wang, Xuefeng; Ohlin, Christian A; Lu, Qinghua; Hu, Jun

2008-05-01

The extracellular matrix in animal tissues usually provides a three-dimensional structural support to cells in addition to performing various other important functions. In the present study, wavy submicrometer laser-irradiated periodic surface structures (LIPSS) were produced on a smooth polystyrene film by polarized laser irradiation with a wavelength of 266 nm. Rat C6 glioma cells exhibited directional migration and oriented division on laser-irradiated polystyrene, which was parallel to the direction of LIPSS. However, rat C6 glioma cells on smooth polystyrene moved in a three-step invasion cycle, with faster migration speed than that on laser-irradiated polystyrene. In addition, focal adhesions examined by immunostaining focal adhesion kinase in human epithelial carcinoma HeLa cells were punctuated on smooth polystyrene, whereas dash-like on laser-irradiated polystyrene. We hypothesized that LIPSS on laser-irradiated polystyrene acted as an anisotropic and persistent mechanical stimulus to guide cell anisotropic spreading, migration and division through focal adhesions.

Template directed assembly of nanoelements in viscous polymer environments

NASA Astrophysics Data System (ADS)

Modi, Satyamkumar

Polymer melt-based manufacturing methods, such as injection molding, offer the potential of directly fabricating three-dimensional parts with nanostructured surfaces in a one-step, high-rate, and solventless process. Electrophoretic deposition has the potential to produce in-mold assembly of nanoparticles during injection molding. The process is fast, is cost effective and can be automated. This electrophoretic deposition, however, has been performed from low-viscosity media and polymer melts are far more viscous. This research provided a fundamental understanding of the electrophoretic deposition process in viscous media. Electrophoresis was performed using a model system of carbon black and polystyrene in tetrahydrofuran (THF). Examined were the effects of processing parameters, polystyrene molecular weight, and carbon black charge. The presence of polystyrene did not prevent deposition of carbon black, but deposition rates decreased at shorter deposition times; deposition was not linear with increasing applied voltage; and greater solution concentrations reduced the critical voltages. A comparison of experimental data with Hamaker's model showed that about 1.6% of the available polystyrene was initially deposited with the carbon black. At voltages above the critical voltage, the deposited mass indicated formation of electrically insulating layers on the electrodes. Increases in polystyrene molecular weight reduced the electrophoretic deposition of the carbon black particles due to increases in suspension viscosity and preferential adsorption of the longer polystyrene chains on the carbon black particles. At low deposition times (≤ 5 seconds), only carbon black deposited onto the electrodes. For longer deposition times, polystyrene co-deposited with the carbon black, with the amount of polystyrene increasing with molecular weight and decreasing with greater charge on the polystyrene molecules. The additional of function groups to the carbon black surface decoupled the carbon black and polystyrene, however, the deposition of the carbon black particles, followed by deposition of a thick layer of polystyrene was observed. This polystyrene deposition was present regardless of the applied voltage, the deposition time, the polystyrene molecular weight, polystyrene material (i.e., charge), and solvent polarity. This deposition behavior suggests that use of lower molecular polymers and unmodified carbon blacks, and control of electrical properties will permit electrophoretic deposition of nanoparticles from polymer melts.

Low-voltage bendable pentacene thin-film transistor with stainless steel substrate and polystyrene-coated hafnium silicate dielectric.

PubMed

Yun, Dong-Jin; Lee, Seunghyup; Yong, Kijung; Rhee, Shi-Woo

2012-04-01

The hafnium silicate and aluminum oxide high-k dielectrics were deposited on stainless steel substrate using atomic layer deposition process and octadecyltrichlorosilane (OTS) and polystyrene (PS) were treated improve crystallinity of pentacene grown on them. Besides, the effects of the pentacene deposition condition on the morphologies, crystallinities and electrical properties of pentacene were characterized. Therefore, the surface treatment condition on dielectric and pentacene deposition conditions were optimized. The pentacene grown on polystyrene coated high-k dielectric at low deposition rate and temperature (0.2-0.3 Å/s and R.T.) showed the largest grain size (0.8-1.0 μm) and highest crystallinity among pentacenes deposited various deposition conditions, and the pentacene TFT with polystyrene coated high-k dielectric showed excellent device-performance. To decrease threshold voltage of pentacene TFT, the polystyrene-thickness on high-k dielectric was controlled using different concentration of polystyrene solution. As the polystyrene-thickness on hafnium silicate decreases, the dielectric constant of polystyrene/hafnium silicate increases, while the crystallinity of pentacene grown on polystyrene/hafnium silicate did not change. Using low-thickness polystyrene coated hafnium silicate dielectric, the high-performance and low voltage operating (<5 V) pentacene thin film transistor (μ: ~2 cm(2)/(V s), on/off ratio, >1 × 10(4)) and complementary inverter (DC gains, ~20) could be fabricated.

21 CFR 177.1640 - Polystyrene and rubber-modified polystyrene.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Polystyrene and rubber-modified polystyrene. 177.1640 Section 177.1640 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) INDIRECT FOOD ADDITIVES: POLYMERS Substances for Use as Basic Components of Single and...

Synchrotron X-ray scattering characterization of the molecular structures of star polystyrenes with varying numbers of arms.

PubMed

Jin, Sangwoo; Higashihara, Tomoya; Jin, Kyeong Sik; Yoon, Jinhwan; Rho, Yecheol; Ahn, Byungcheol; Kim, Jehan; Hirao, Akira; Ree, Moonhor

2010-05-20

We have synthesized well-defined multiarmed star polystyrenes, with 6, 9, 17, 33, and 57 arms, and studied their molecular shapes and structural characteristics in a good solvent (tetrahydrofuran at 25 degrees C) and in a theta (Theta) solvent (cyclohexane at 35 degrees C) by small-angle X-ray scattering (SAXS) using a synchrotron radiation source. Analysis of the SAXS data provided a detailed characterization of the molecular shapes, including the contributions of the blob morphology of the arms, the radius of gyration, the paired distance distribution, the radial electron density distribution, and the Zimm-Stockmayer and Roovers g-factor, for the multiarmed star polystyrenes. In particular, the molecular shapes of the star polystyrenes were found to change from a fuzzy ellipsoid, for the 6-armed polystyrene, to a fuzzy sphere, for the 57-armed polystyrene, with an increasing number of arms. The ellipsoidal character of the star polystyrenes with fewer arms may originate from the extended anisotropically branched architecture at the center of the molecule. The arms of the star polystyrenes were found to be more extended than those of the linear polystyrenes. Furthermore, the degree of chain extension in the arms increased with the number of arms.

HIV Pre-Exposure Prophylaxis Stigma as a Multidimensional Barrier to Uptake Among Women Who Attend Planned Parenthood.

PubMed

Calabrese, Sarah K; Dovidio, John F; Tekeste, Mehrit; Taggart, Tamara; Galvao, Rachel W; Safon, Cara B; Willie, Tiara C; Caldwell, Abigail; Kaplan, Clair; Kershaw, Trace S

2018-05-22

PrEP uptake has lagged among US women. PrEP stigma is a recognized barrier to uptake among MSM but remains largely unexplored among women. This study examined the pervasiveness of PrEP stigma among US women and its implications for uptake. Setting/Methods: In a 2017 online survey of Planned Parenthood patients drawn from the three cities with the highest numbers of new HIV infections in Connecticut, 597 heterosexually-active, HIV-negative, PrEP-inexperienced women reported background characteristics, two dimensions of anticipated PrEP stigma (PrEP-user stereotypes and PrEP disapproval by others), and three indicators of potential PrEP uptake (interest in learning more about PrEP, intention to use PrEP, and comfort discussing PrEP with a provider). Participants commonly perceived PrEP-user stereotypes, with many believing that others would regard them as promiscuous (37%), HIV-positive (32%), bad (14%), or gay (11%) if they used PrEP. Thirty percent would feel ashamed to disclose PrEP use. Many participants expected disapproval by family (36%), sex partners (34%), and friends (25%). In adjusted analyses, perception of PrEP-user stereotypes was uniquely associated with lower comfort discussing PrEP with a provider. Expected PrEP disapproval by others was uniquely associated with less PrEP interest, less intention to use PrEP, and less comfort discussing PrEP with a provider. Exploratory moderation analyses suggested intention to use PrEP was greatest when participants anticipated low levels of both PrEP-user stereotypes and PrEP disapproval by others. Findings highlight the need for positive messaging targeting potential PrEP users and their social networks to increase PrEP acceptance and uptake.

77 FR 65935 - Notice of Application for Approval of Discontinuance or Modification of a Railroad Signal System

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-31

... NS Port Road Branch from Perrysburg, MD, Milepost (MP) PD-0.3, to Enola, PA, MP EP-68.2. The discontinuance would include automatic signals: PD 1.9, PD 6.4, PD 9.7, PD 15.7, PD 18.7, PD 23.6, PD 28.8, PD 35.7, EP 35.2, EP 40.0, EP 42.4, EP 47.6, EP 49.5, EP 53.6, EP 54.0, EP 58.3, EP 62.8, EP 67.1. The...

Sodium Polystyrene Sulfonate

MedlinePlus

Sodium polystyrene sulfonate is used to treat hyperkalemia (increased amounts of potassium in the body). Sodium polystyrene sulfonate is in a class of medications called potassium-removing agents. It works by ...

Functional and bioinformatics analysis of an exopolysaccharide-related gene (epsN) from Lactobacillus kefiranofaciens ZW3.

PubMed

Wang, Jingrui; Tang, Wei; Zheng, Yongna; Xing, Zhuqing; Wang, Yanping

2016-09-01

A novel lactic acid bacteria strain Lactobacillus kefiranofaciens ZW3 exhibited the characteristics of high production of exopolysaccharide (EPS). The epsN gene, located in the eps gene cluster of this strain, is associated with EPS biosynthesis. Bioinformatics analysis of this gene was performed. The conserved domain analysis showed that the EpsN protein contained MATE-Wzx-like domains. Then the epsN gene was amplified to construct the recombinant expression vector pMG36e-epsN. The results showed that the EPS yields of the recombinants were significantly improved. By determining the yields of EPS and intracellular polysaccharide, it was considered that epsN gene could play its Wzx flippase role in the EPS biosynthesis. This is the first time to prove the effect of EpsN on L. kefiranofaciens EPS biosynthesis and further prove its functional property.

EpsA is an essential gene in exopolysaccharide production in Lactobacillus johnsonii FI9785.

PubMed

Dertli, Enes; Mayer, Melinda J; Colquhoun, Ian J; Narbad, Arjan

2016-07-01

Lactobacillus johnsonii FI9785 has an eps gene cluster which is required for the biosynthesis of homopolymeric exopolysaccharides (EPS)-1 and heteropolymeric EPS-2 as a capsular layer. The first gene of the cluster, epsA, is the putative transcriptional regulator. In this study we showed the crucial role of epsA in EPS biosynthesis by demonstrating that deletion of epsA resulted in complete loss of both EPS-1 and EPS-2 on the cell surface. Plasmid complementation of the epsA gene fully restored EPS production, as confirmed by transmission electron microscopy and nuclear magnetic resonance (NMR) analysis. Furthermore, this complementation resulted in a twofold increase in the expression levels of this gene, which almost doubled amounts of EPS production in comparison with the wild-type strain. Analysis of EPS by NMR showed an increased ratio of the heteropolysaccharide to homopolysaccharide in the complemented strain and allowed identification of the acetylated residue in EPS-2 as the (1,4)-linked βGlcp unit, with the acetyl group located at O-6. These findings indicate that epsA is a positive regulator of EPS production and that EPS production can be manipulated by altering its expression. © 2015 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

Enhanced sensitivity of a microfabricated resonator using a graphene-polystyrene bilayer membrane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yun, Minhyuk; Lee, Eunho; Cho, Kilwon

2014-08-18

A graphene layer was synthesized using chemical vapor deposition methods and a polystyrene solution was spin-cast onto the graphene film. The graphene-polystyrene bilayer membrane was attached between the two tines of a microfabricated quartz tuning fork (QTF). The modulus of the graphene-polystyrene bilayer was measured to be twice that of a pristine polystyrene membrane. Exposure of the membrane-coated QTF to ethanol vapor decreased the resonance frequency of the microresonator. The bilayer membrane-coated QTF produced a frequency change that was three times the change obtained using a polystyrene membrane-coated QTF, with a lower degree of degradation in the Q factor. Themore » limit of detection of the bilayer membrane-coated QTF to ethanol vapor was determined to be 20 ppm.« less

Selective Permeating Properties of Butanol and Water through Polystyrene- b-polydimethylsiloxane- b-polystyrene Pervaporation Membranes

NASA Astrophysics Data System (ADS)

Shin, Chaeyoung; Baer, Zachary; Chen, X. Chelsea; Ozcam, A. Evren; Clark, Douglas; Balsara, Nitash

2015-03-01

Polystyrene- b-polydimethylsiloxane- b-polystyrene (SDS) membranes have been studied in butanol-water binary pervaporation experiments and pervaporation experiments integrated with viable fermentation broths. Polydimethylsiloxane has been widely known to be a suitable material for separating organic chemicals from aqueous solutions, and it thus provides a continuous matrix phase in SDS membranes for permeation of small molecules. The polystyrene block provides mechanical stability to maintain the membrane structure in the pervaporation membranes. We take advantage of these features to fabricate a thin and butanol-selective SDS membrane for in situ product removal in fermentation.

Insights on Flow Behavior of Foam in Unsaturated Porous Media during Soil Flushing.

PubMed

Zhao, Yong S; Su, Yan; Lian, Jing R; Wang, He F; Li, Lu L; Qin, Chuan Y

2016-11-01

  One-dimensional column and two-dimensional tank experiments were carried out to determine (1) the physics of foam flow and propagation of foaming gas, foaming liquid, and foam; (2) the pressure distribution along foam flow and the effect of media permeability, foam flow rate and foam quality on foam injection pressure; and (3) the migration and distribution property of foam flow in homogeneous and heterogeneous sediments. The results demonstrated that: (1) gas and liquid front were formed ahead of the foam flow front, the transport speed order is foaming gas > foaming liquid > foam flowing; (2) injection pressure mainly comes from the resistance to bubble migration. Effect of media permeability on foam injection pressure mainly depends on the physics and behavior of foam flow; (3) foam has a stronger capacity of lateral spreading, besides, foam flow was uniformly distributed across the foam-occupied region, regardless of the heterogeneity of porous media.

Production of extracellular polymeric substances (EPS) by Serratia sp.1 using wastewater sludge as raw material and flocculation activity of the EPS produced.

PubMed

Bezawada, J; Hoang, N V; More, T T; Yan, S; Tyagi, N; Tyagi, R D; Surampalli, R Y

2013-10-15

Growth profile and extracellular polymeric substances (EPS) production of Serratia sp.1 was studied in shake flask fermentation for 72 h using wastewater sludge as raw material. Maximum cell concentration of 6.7 × 10(9) cfu/mL was obtained at 48 h fermentation time. EPS dry weight, flocculation activity and dewaterability of different EPS (tightly bound or TB-EPS, loosely bound or LB-EPS and broth-EPS or B-EPS) were also measured. The highest concentration of LB-EPS (2.45 g/L) and TB-EPS (0.99 g/L) were attained at 48 h of fermentation. Maximum flocculation activity and dewaterability (ΔCST) of TB-EPS (76.4%, 14.5s and 76.5%, 15.5s), LB-EPS (67.8%, 8.1s and 64.7%, 7.6s) and broth EPS (61%, 6.1s and 70.4%, 6.8s) were obtained at 36 and 48 h of growth. Higher flocculation activity and dewaterability were achieved with TB-EPS than with the two other EPS. Characterization of TB-EPS and LB-EPS was done in terms of their protein and carbohydrate content. Protein content was much higher in TB-EPS where as carbohydrate content was only slightly higher in TB-EPS than LB-EPS. Morphology of the Serratia strain after fermentation in sludge and TSB was observed under a scanning electron microscope and the cell size was found to be bigger in the sludge medium than the TSB medium. Copyright © 2013 Elsevier Ltd. All rights reserved.

Prostaglandin E2 regulates melanocyte dendrite formation through activation of PKCζ

PubMed Central

Scott, Glynis; Fricke, Alex; Fender, Anne; McClelland, Lindy; Jacobs, Stacey

2007-01-01

Prostaglandins are lipid signaling intermediates released by keratinocytes in response to ultraviolet irradiation (UVR) in the skin. The main prostaglandin released following UVR is PGE2, a ligand for 4 related G-protein coupled receptors (EP1, EP2, EP3 and EP4). Our previous work established that PGE2 stimulates melanocyte dendrite formation through activation of the EP1 and EP3 receptors. The purpose of the present report is to define the signaling intermediates involved in EP1 and EP3-dependent dendrite formation in human melanocytes. We recently showed that activation of the atypical PKCζ isoform stimulates melanocyte dendricity in response to treatment with lysophosphatidylcholine. We therefore examined the potential contribution of PKCζ activation on EP1 and EP3-dependent dendrite formation in melanocytes. Stimulation of the EP1 and EP3 receptors by selective agonists activated PKCζ, and inhibition of PKCζ activation abrogated EP1 and EP3-receptor mediated melanocyte dendricity. Because of the importance of Rho-GTP binding proteins in the regulation of melanocyte dendricity, we also examined the effect of EP1 and EP3 receptor activation on Rac and Rho activity. Neither Rac nor Rho was activated upon treatment with EP1,3-receptor agonists. We show that melanocytes express only the EP3A1 isoform, but not the EP3B receptor isoform, previously associated with Rho activation, consistent with a lack of Rho stimulation by EP3 agonists. Our data suggest that PKCζ activation plays a predominant role in regulation of PGE2-dependent melanocyte dendricity. PMID:17850789

Investigation on Wall Panel Sandwiched With Lightweight Concrete

NASA Astrophysics Data System (ADS)

Lakshmikandhan, K. N.; Harshavardhan, B. S.; Prabakar, J.; Saibabu, S.

2017-08-01

The rapid population growth and urbanization have made a massive demand for the shelter and construction materials. Masonry walls are the major component in the housing sector and it has brittle characteristics and exhibit poor performance against the uncertain loads. Further, the structure requires heavier sections for carrying the dead weight of masonry walls. The present investigations are carried out to develop a simple, lightweight and cost effective technology for replacing the existing wall systems. The lightweight concrete is developed for the construction of sandwich wall panel. The EPS (Expanded Polystyrene) beads of 3 mm diameter size are mixed with concrete and developed a lightweight concrete with a density 9 kN/m3. The lightweight sandwich panel is cast with a lightweight concrete inner core and ferrocement outer skins. This lightweight wall panel is tested for in-plane compression loading. A nonlinear finite element analysis with damaged plasticity model is carried out with both material and geometrical nonlinearities. The experimental and analytical results were compared. The finite element study predicted the ultimate load carrying capacity of the sandwich panel with reasonable accuracy. The present study showed that the lightweight concrete is well suitable for the lightweight sandwich wall panels.

Optimizing the position of insulating materials in flat roofs exposed to sunshine to gain minimum heat into buildings under periodic heat transfer conditions.

PubMed

Shaik, Saboor; Talanki, Ashok Babu Puttranga Setty

2016-05-01

Building roofs are responsible for the huge heat gain in buildings. In the present work, an analysis of the influence of insulation location inside a flat roof exposed directly to the sun's radiation was performed to reduce heat gain in buildings. The unsteady thermal response parameters of the building roof such as admittance, transmittance, decrement factor, and time lags have been investigated by solving a one-dimensional diffusion equation under convective periodic boundary conditions. Theoretical results of four types of walls were compared with the experimental results available in literature. The results reveal that the roof with insulation placed at the outer side and at the center plane of the roof is the most energy efficient from the lower decrement factor point of view and the roof with insulation placed at the center plane and the inner side of the roof is the best from the highest time lag point of view among the seven studied configurations. The composite roof with expanded polystyrene insulation located at the outer side and at the center plane of the roof is found to be the best roof from the lowest decrement factor (0.130) point of view, and the composite roof with resin-bonded mineral wool insulation located at the center plane and at the inner side of the roof is found to be energy efficient from the highest time lag point (9.33 h) of view among the seven configurations with five different insulation materials studied. The optimum fabric energy storage thicknesses of reinforced cement concrete, expanded polystyrene, foam glass, rock wool, rice husk, resin-bonded mineral wool, and cement plaster were computed. From the results, it is concluded that rock wool has the least optimum fabric energy storage thickness (0.114 m) among the seven studied building roof materials.

Home-based pre-exposure prophylaxis (PrEP) services for gay and bisexual men: An opportunity to address barriers to PrEP uptake and persistence

PubMed Central

Rendina, H. Jonathon; Grov, Christian

2017-01-01

Gay, bisexual, and other men who have sex with men (GBM) are disproportionately affected by the HIV epidemic. Despite the promise of pre-exposure prophylaxis (PrEP) in reducing HIV transmission risk, barriers for uptake and persistence exist. We sought to identify whether GBM in a nationwide cohort who have not yet initiated PrEP (n = 906) would prefer to get PrEP-related care from a primary care provider (PCP) compared to a specialist clinic or provider. We then sought to identify their level of interest and factors associated with preference for using home-based PrEP services (i.e., HB-PrEP), defined to participants as conducting HIV/STI self-testing from home with PrEP prescription mailing after an initial in-person clinic visit. We examined the associations of demographics, sexual HIV transmission risk, concern about frequent medical checkups associated with PrEP, health care access, and PrEP intentions with preferences for healthcare provider type and HB-PrEP. Concern about frequent medical checkups were associated with preferring a PCP for PrEP-related care, but men who perceived a barrier to bringing up the topic of PrEP with a doctor preferred a specialist clinic or provider more than a PCP. HB-PrEP was more appealing for younger men and those engaged in sexual HIV transmission risk, suggesting HB-PrEP could help reach GBM most vulnerable to HIV and in need of PrEP. HB-PrEP expansion has potential to increase PrEP uptake and persistence among GBM, particularly for men with barriers to clinic-based care and higher intentions to initiate PrEP. Clinical guidelines regarding HB-PrEP are needed to expand its use. PMID:29281688

An Apparatus for Sizing Particulate Matter in Solid Rocket Motors.

DTIC Science & Technology

1984-06-01

accurately measured. A curve for sizing polydispersions was presented which was used by Cramer and Hansen [Refs. 2, 12]. Two phase flow losses are often...Concentration...... 54 18. 5 Micron Polystyrene, Curve Fit .......... ... 55 19. 5 Micron Polystyrene, Two Angle Method ........ .56.... 20. 10 Micron...Polystyrene, Curve Fit .. ........ 57....[57 21. 10 Micron Polystyrene, Two Angle Method .. ....... .58 . . .6_ *22. 20J Mizron P3iystvrene Cu. .Fi

Prostaglandin E2 modulates dendritic cell function via EP2 and EP4 receptor subtypes.

PubMed

Harizi, Hedi; Grosset, Christophe; Gualde, Norbert

2003-06-01

We have reported previously that PGE(2) inhibits dendritic cells (DC) functions. Because E prostanoid receptor (EPR) subtypes involved in this action are unknown, expression and functions of these receptors were examined in DC. Western blot and flow cytometry analyses showed that all EPRs were coexpressed in DC. In a dose-dependent manner, lipopolysaccharide (LPS) enhanced EP(2)R/EP(4)R but not EP(1)R/EP(3)R expressions. NS-398, a cyclooxygenase (COX)-2-selective inhibitor, suppressed LPS-enhanced EP(2)R/EP(4)R expression, suggesting that COX-2-issued prostaglandin E(2) (PGE(2)) modulates DC function through stimulation of specific EPR subtypes. Using selective agonists, we found that butaprost, an EP(2)R agonist, and PGE(1) alcohol, an EP(2)R and EP(2)R/EP(4)R agonist, inhibited major histocompatibility complex class II expression and enhanced interleukin-10 production from DC. However, no effect was observed with sulprostone and 17-phenyl-omega-trinor-PGE(2), selective agonists for EP(1)R and EP(1)R/EP(3)R, respectively. Treatment of DC with dibutyryl cyclic adenosine monophosphate (cAMP), an analog of cAMP, mimics PGE(2)-induced, inhibitory effects. Taken together, our data demonstrate that EP(2)R/EP(4)R are efficient for mediating PGE(2)-induced modulation of DC functions.

Innovative combination of electrolysis and Fe(II)-activated persulfate oxidation for improving the dewaterability of waste activated sludge.

PubMed

Zhen, Guang-Yin; Lu, Xue-Qin; Li, Yu-You; Zhao, You-Cai

2013-05-01

The feasibility of electrolysis integrated with Fe(II)-activated persulfate (S2O8(2-)) oxidation to improve waste activated sludge (WAS) dewaterability was evaluated. The physicochemical properties (sludge volume (SV), total suspended solids (TSS) and volatile suspended solids (VSS)) and extracellular polymeric substances (EPS), including slime EPS, loosely bound EPS (LB-EPS) and tightly bound EPS (TB-EPS) were characterized to identify their exact roles in sludge dewatering. While dewaterability negatively corresponded to LB-EPS, TB-EPS, protein (PN) and polysaccharide (PS) in LB-EPS and TB-EPS, it was independent of SV, TSS, VSS, slime EPS and PN/PS. Further study through scanning electron microscope (SEM) verified the entrapment of bacterial cells by TB-EPS, protecting them against electrolysis disruption. Comparatively, electrolysis integrated with S2O8(2-)/Fe(II) oxidation was able to effectively disrupt the protective barrier and crack the entrapped cells, releasing the water inside EPS and cells. Therefore, the destruction of both TB-EPS and cells is the fundamental reason for the enhanced dewaterability. Copyright © 2013 Elsevier Ltd. All rights reserved.

Influence of loosely bound extracellular polymeric substances (EPS) on the flocculation, sedimentation and dewaterability of activated sludge.

PubMed

Li, X Y; Yang, S F

2007-03-01

Laboratory experiments on the activated sludge (AS) process were carried out to investigate the influence of microbial extracellular polymeric substances (EPS), including loosely bound EPS (LB-EPS) and tightly bound EPS (TB-EPS), on biomass flocculation, sludge settlement and dewaterability. The heat EPS extraction method was modified to include a mild step and a harsh step for extracting the LB-EPS and TB-EPS, respectively, from the sludge suspension. Six lab-scale AS reactors were used to grow AS with different carbon sources of glucose and sodium acetate, and different sludge retention times (SRTs) of 5, 10 and 20 days. The variation in the bioreactor condition produced sludge with different abundances of EPS and different flocculation and separation characteristics. The sludge that was fed on glucose had more EPS than the sludge that was fed on acetate. For any of the feeding substrates, the sludge had a nearly consistent TB-EPS value regardless of the SRT, and an LB-EPS content that decreased with the SRT. The acetate-fed sludge performed better than the glucose-fed sludge in terms of bioflocculation, sludge sedimentation and compression, and sludge dewaterability. The sludge flocculation and separation improved considerably as the SRT lengthened. The results demonstrate that the LB-EPS had a negative effect on bioflocculation and sludge-water separation. The parameters for the performance of sludge-water separation were much more closely correlated with the amount of LB-EPS than with the amount of TB-EPS. It is argued that although EPS is essential to sludge floc formation, excessive EPS in the form of LB-EPS could weaken cell attachment and the floc structure, resulting in poor bioflocculation, greater cell erosion and retarded sludge-water separation.

Pharmacological characterization of the inhibitory activity of beta h-endorphin (beta h-EP), [Arg9,19,24,28,29]-beta h-EP, [Gln8,Gly31]-beta h-EP-Gly-Gly-NH2, in the neuroeffector junction of the mouse vas deferens.

PubMed

Valenzuela, R; Li, C H; Huidobro-Toro, J P

1991-08-01

The inhibitory opioid activities of beta h-endorphin (beta h-EP), its structurally related peptide analogues [Gln8,Gly31]-beta h-EP-Gly-Gly-NH2 (Gly-Gly-beta h-EP), [Arg9,19,24,28,29]-beta h-EP (Arg-beta h-EP) and methionine enkephalin have been examined in the electrically stimulated mouse vas deferens bioassay. All four peptides behaved as full agonists; methionine enkephalin was the most potent followed by Arg-beta h-EP, beta h-EP and Gly-Gly-beta h-EP. Neither Gly-Gly-beta h-EP nor Arg-beta h-EP antagonized the inhibitory action of beta h-EP or methionine enkephalin. An hour of tissue exposure to 30 nM beta-funaltrexamine followed by thorough washing, displaced to the right, in a parallel fashion, the concentration-response curves of beta h-EP and analogues. Whereas the displacement of the concentration response curves was 8 to 10-fold for beta h-EP and Arg-beta h-EP, it was only about 3-fold for Gly-Gly-beta h-EP and methionine enkephalin. Naltrindole was the most potent antagonist of methionine enkephalin with an apparent pA2 of 9.4; its potency as an antagonist of beta h-EP and related analogues was approximately one-tenth of this with pA2 values approximately 8.5. Norbinaltorphimine also antagonized the action of the opioid peptides with pA2 values close to 7.8.

The Crystal Structure of a Binary Complex of Two Pseudopilins: EpsI And EpsJ From the Type 2 Secretion System of Vibrio Vulnificus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yanez, M.E.; Korotkov, K.V.; Abendroth, J.

2009-05-28

Type II secretion systems (T2SS) translocate virulence factors from the periplasmic space of many pathogenic bacteria into the extracellular environment. The T2SS of Vibrio cholerae and related species is called the extracellular protein secretion (Eps) system that consists of a core of multiple copies of 11 different proteins. The pseudopilins, EpsG, EpsH, EpsI, EpsJ and EpsK, are five T2SS proteins that are thought to assemble into a pseudopilus, which is assumed to interact with the outer membrane pore, and may actively participate in the export of proteins. We report here biochemical evidence that the minor pseudopilins EpsI and EpsJ frommore » Vibrio species interact directly with one another. Moreover, the 2.3 {angstrom} resolution crystal structure of a complex of EspI and EpsJ from Vibrio vulnificus represents the first atomic resolution structure of a complex of two different pseudopilin components from the T2SS. Both EpsI and EpsJ appear to be structural extremes within the family of type 4a pilin structures solved to date, with EpsI having the smallest, and EpsJ the largest, 'variable pilin segment' seen thus far. A high degree of sequence conservation in the EpsI:EpsJ interface indicates that this heterodimer occurs in the T2SS of a large number of bacteria. The arrangement of EpsI and EpsJ in the heterodimer would correspond to a right-handed helical character of proteins assembled into a pseudopilus.« less

Adolescent Human Immunodeficiency Virus Care Providers’ Attitudes Toward the Use of Oral Pre-Exposure Prophylaxis in Youth

PubMed Central

Zimet, Gregory; Lally, Michelle; Kahn, Jessica A.

2016-01-01

Abstract Oral pre-exposure prophylaxis (PrEP) for human immunodeficiency virus (HIV) prevention is currently indicated for use in adults in the United States and may soon be indicated for minor adolescents. However, implementation of PrEP use among minors may present unique barriers. We conducted 15 individual, semi-structured interviews among US clinicians caring for HIV-infected and at-risk youth. The theory-driven interview guide assessed demographics, perceived role of oral PrEP in HIV prevention among adolescents, perceived barriers to and facilitating factors for use of PrEP in adolescents, and clinician-reported likelihood of prescribing PrEP. Transcripts were analyzed using framework analysis. Overall, clinicians viewed PrEP as a time-limited intervention that is one part of a comprehensive approach to HIV prevention among adolescents. Perceived barriers to prescribing to minors included concerns about: confidentiality, legality of minors consenting to PrEP without parental involvement, ability of minors to understand the risks/benefits of PrEP, the possible impact of PrEP on bone accrual, off-label use of PrEP medication in minors, and the high costs associated with PrEP use. Clinician-reported facilitating factors for prescribing PrEP to youth included educating communities and other clinicians about PrEP, ensuring adequate financial resources and infrastructure for delivering PrEP, developing formal guidance on effective behavioral interventions that should be delivered with PrEP, and gaining personal experience with prescribing PrEP. Clinicians indicated greater comfort with prescribing PrEP to adults versus minors. For PrEP to become more widely available to youth at risk for HIV infection, barriers that are unique to PrEP use in minors must be addressed. PMID:27410497

“Support Your Client at the Space That They're in”: HIV Pre-Exposure Prophylaxis (PrEP) Prescribers' Perspectives on PrEP-Related Risk Compensation

PubMed Central

Magnus, Manya; Mayer, Kenneth H.; Krakower, Douglas S.; Eldahan, Adam I.; Hawkins, Lauren A. Gaston; Underhill, Kristen; Hansen, Nathan B.; Kershaw, Trace S.; Betancourt, Joseph R.; Dovidio, John F.

2017-01-01

Abstract Despite the demonstrated effectiveness of HIV pre-exposure prophylaxis (PrEP) and evidence that most PrEP users do not engage in risk compensation (i.e., increased risk behavior due to a perceived decrease in HIV susceptibility), some healthcare providers report patient risk compensation to be a deterrent to prescribing PrEP. Overcoming this barrier is essential to supporting PrEP access and uptake among people at risk for HIV. To inform such efforts, this qualitative study explored PrEP-related risk compensation attitudes among providers with firsthand experience prescribing PrEP. US-based PrEP providers (n = 18), most of whom were HIV specialists, were recruited through direct outreach and referral from colleagues and other participants. Individual 90-min semistructured interviews were conducted by phone or in person from September 2014 through February 2015, transcribed, and thematically analyzed. Three attitudinal themes emerged: (1) providers' role is to support patients in making informed decisions, (2) risk behavior while taking PrEP does not fully offset PrEP's protective benefit (i.e., PrEP confers net protection, even with added behavioral risk), and (3) PrEP-related risk compensation is unduly stigmatized within and beyond the healthcare community. Participants were critical of other healthcare providers' negative judgment of patients and reluctance to prescribe PrEP due to anticipated risk compensation. Several providers also acknowledged an evolution in their thinking from initial ambivalence toward greater acceptance of PrEP and PrEP-related behavior change. PrEP providers' insights about risk compensation may help to address unsubstantiated concerns about PrEP-related risk compensation and challenge the acceptability of withholding PrEP on these grounds. PMID:28414261

A photosensitizer delivered by bispecific antibody redirected T lymphocytes enhances cytotoxicity against EpCAM-expressing carcinoma cells upon light irradiation.

PubMed

Blaudszun, André-René; Moldenhauer, Gerhard; Schneider, Marc; Philippi, Anja

2015-01-10

Recently conducted clinical trials have provided impressive evidence that chemotherapy resistant metastatic melanoma and several hematological malignancies can be cured using adoptive T cell therapy or T cell-recruiting bispecific antibodies. However, a significant fraction of patients did not benefit from these treatments. Here we have evaluated the feasibility of a novel combination therapy which aims to further enhance the killing potential of bispecific antibody-redirected T lymphocytes by using these cells as targeted delivery system for photosensitizing agents. For a first in vitro proof-of-concept study, ex vivo activated human donor T cells were loaded with a poly(styrene sulfonate) (PSS)-complex of the model photosensitizer 5,10,15,20-tetrakis(3-hydroxyphenyl)porphyrin (mTHPP). In the absence of light and when loading with the water-soluble PSS/mTHPP-complex occurred at a tolerable concentration, viability and cytotoxic function of loaded T lymphocytes were not impaired. When "drug-enhanced" T cells were co-cultivated with EpCAM-expressing human carcinoma cells, mTHPP was transferred to target cells. Notably, in the presence of a bispecific antibody, which cross-links effector and target cells thereby inducing the cytolytic activity of cytotoxic T lymphocytes, significantly more photosensitizer was transferred. Consequently, upon irradiation of co-cultures, redirected drug-loaded T cells were more effective in killing A549 lung and SKOV-3 ovarian carcinoma cells than retargeted unloaded T lymphocytes. Particularly, the additive approach using redirected unloaded T cells in combination with appropriate amounts of separately applied PSS/mTHPP was less efficient as well. Thus, by loading T lymphocytes with a stimulus-sensitive anti-cancer drug, we were able to enhance the cytotoxic capacity of carrier cells. Photosensitizer boosted T cells could open new perspectives for adoptive T cell therapy as well as targeted photodynamic therapy. Copyright © 2014 Elsevier B.V. All rights reserved.

Current applications of foams formed from mixed surfactant-polymer solutions.

PubMed

Bureiko, Andrei; Trybala, Anna; Kovalchuk, Nina; Starov, Victor

2015-08-01

Foams cannot be generated without the use of special foaming agents, as pure liquids do not foam. The most common foaming agents are surfactants, however often for foam stability one active agent is not enough, it is necessary to add other component to increase foam lifetime. Foams on everyday use are mostly made from mixture of different components. Properly chosen combinations of two active ingredients lead to a faster foam formation and increased foam stability. During the last decade polymers (mainly polyelectrolytes and proteins) have become frequently used additives to foaming solutions. Mixtures of surfactants and polymers often demonstrate different foaming properties in comparison to surfactant only or polymer only solutions. The nature of surfactant-polymer interactions is complicated and prediction of resulting foaming properties of such formulations is not straightforward. Properties and foaming of surfactant-polymer mixtures are discussed as well as current applications of foams and foaming agents as foams are widely used in cosmetics, pharmaceutics, medicine and the food industry. Copyright © 2014 Elsevier B.V. All rights reserved.

Structure design of and experimental research on a two-stage laval foam breaker for foam fluid recycling.

PubMed

Wang, Jin-song; Cao, Pin-lu; Yin, Kun

2015-07-01

Environmental, economical and efficient antifoaming technology is the basis for achievement of foam drilling fluid recycling. The present study designed a novel two-stage laval mechanical foam breaker that primarily uses vacuum generated by Coanda effect and Laval principle to break foam. Numerical simulation results showed that the value and distribution of negative pressure of two-stage laval foam breaker were larger than that of the normal foam breaker. Experimental results showed that foam-breaking efficiency of two-stage laval foam breaker was higher than that of normal foam breaker, when gas-to-liquid ratio and liquid flow rate changed. The foam-breaking efficiency of normal foam breaker decreased rapidly with increasing foam stability, whereas the two-stage laval foam breaker remained unchanged. Foam base fluid would be recycled using two-stage laval foam breaker, which would reduce the foam drilling cost sharply and waste disposals that adverse by affect the environment.

Prostaglandin receptors EP1-4 as a potential marker for clinical outcome in urothelial bladder cancer.

PubMed

von der Emde, Laura; Goltz, Diane; Latz, Stefan; Müller, Stefan C; Kristiansen, Glen; Ellinger, Jörg; Syring, Isabella

2014-01-01

Prostaglandins, especially prostaglandin E2 (PGE2), and COX-2 play an important role in carcinogenesis of many tumors including bladder cancer (BCA). The PGE2 receptors EP1-4 regulate tumor cell growth, invasion and migration in different tumor entities but EP expression in BCA remains to be determined. In the present study we examined the expression of EP1-4 in non-muscle invasive bladder cancer (NMIBC), muscle invasive bladder cancer (MIBC) and normal urothelial tissue (NU) using immunohistochemistry. Nuclear and cytoplasmic EP1-4 expression was correlated with clinicopathological parameters and survival of BCA patients. EP1, EP2 and EP3 were significantly less expressed in the cytoplasm und nucleus of NMIBC and MIBC than in NU; EP4 cytoplasmic staining in MIBC was significantly higher compared to NU. The cytoplasmic staining was significantly more abundant in MIBC than in NMIBC in all investigated receptors except EP2. The level of EP staining in NMIBC was correlated with staging and grading, especially cytoplasmic EP1. Nuclear staining of EP1 was an independent predictor of BCA recurrence-free survival in NMIBC patients. EP receptors are dysregulated in BCA. The increase of EP1 may be used as prognostic parameter in NMIBC patients and its dysregulation could be targeted by specific EP1 inhibitors.

Prostaglandin receptors EP1-4 as a potential marker for clinical outcome in urothelial bladder cancer

PubMed Central

von der Emde, Laura; Goltz, Diane; Latz, Stefan; Müller, Stefan C; Kristiansen, Glen; Ellinger, Jörg; Syring, Isabella

2014-01-01

Prostaglandins, especially prostaglandin E2 (PGE2), and COX-2 play an important role in carcinogenesis of many tumors including bladder cancer (BCA). The PGE2 receptors EP1-4 regulate tumor cell growth, invasion and migration in different tumor entities but EP expression in BCA remains to be determined. In the present study we examined the expression of EP1-4 in non-muscle invasive bladder cancer (NMIBC), muscle invasive bladder cancer (MIBC) and normal urothelial tissue (NU) using immunohistochemistry. Nuclear and cytoplasmic EP1-4 expression was correlated with clinicopathological parameters and survival of BCA patients. EP1, EP2 and EP3 were significantly less expressed in the cytoplasm und nucleus of NMIBC and MIBC than in NU; EP4 cytoplasmic staining in MIBC was significantly higher compared to NU. The cytoplasmic staining was significantly more abundant in MIBC than in NMIBC in all investigated receptors except EP2. The level of EP staining in NMIBC was correlated with staging and grading, especially cytoplasmic EP1. Nuclear staining of EP1 was an independent predictor of BCA recurrence-free survival in NMIBC patients. EP receptors are dysregulated in BCA. The increase of EP1 may be used as prognostic parameter in NMIBC patients and its dysregulation could be targeted by specific EP1 inhibitors. PMID:25520883

Prevalence of actual uptake and willingness to use pre-exposure prophylaxis to prevent HIV acquisition among men who have sex with men in Hong Kong, China

PubMed Central

Lau, Joseph T. F.; Fang, Yuan; Ip, Mary; Gross, Danielle L.

2018-01-01

Objectives This study was to investigate the prevalence of actual uptake of pre-exposure prophylaxis (PrEP), willingness to use daily oral PrEP under two cost scenarios, and potential issues related to PrEP use among men who have sex with men (MSM) with HIV negative/unknown sero-status in Hong Kong, China. Factors associated with the two measures of willingness were also investigated. Methods 403 eligible MSM completed the anonymous venue-based face-to-face interview/telephone interview. Results Only 1% had ever used PrEP. After being briefed about some facts of PrEP, the prevalence of willingness to use daily oral PrEP was 7.7% if they could purchase PrEP at private hospitals/clinics at HK$8,000 (US$1,032)/month (market rate) and 45.2% if free PrEP was provided by public hospitals/clinics in Hong Kong (free PrEP). After adjusted for significant background variables, significant factors of these two measures of willingness included: (1) number of correct responses to knowledge on PrEP, (2) perceived risk of HIV infection in the next six months, and (3) constructs of the Theory of Planned Behavior: positive and negative attitudes toward PrEP, perceived their significant others would support them take PrEP (perceived subjective norm), perceived number of local MSM who were willing to take PrEP (perceived descriptive norm), and confidence in using PrEP under the two scenarios (perceived behavioral control). Among all participants, 9.7% and 25.1% would start and discontinue using PrEP without consulting doctors; 26.0% would not take PrEP daily if it was provided for free, and 42.4% would not take up HIV testing every 3 months after using PrEP. Conclusion Different strategies should be considered for promoting PrEP at market rate and if free PrEP is made available. Future promotion should increase their knowledge about PrEP, modify their perceptions related to HIV and PrEP, and address some potential issues related to PrEP use. PMID:29432470

Effect of salinity on extracellular polymeric substances of activated sludge from an anoxic-aerobic sequencing batch reactor.

PubMed

Wang, Zichao; Gao, Mengchun; Wang, Zhe; She, Zonglian; Chang, Qingbo; Sun, Changqing; Zhang, Jian; Ren, Yun; Yang, Ning

2013-11-01

The effect of salinity on extracellular polymeric substances (EPS) of activated sludge was investigated in an anoxic-aerobic sequencing batch reactor (SBR). The contents of loosely bound EPS (LB-EPS) and tightly bound EPS (TB-EPS) were positively correlated with the salinity. The polysaccharide (PS) and protein (PN) contents in both LB-EPS and TB-EPS increased with the increase of salinity. With the increase of salinity from 0.5% to 6%, the PN/PS ratios in LB-EPS and TB-EPS decreased from 4.8 to 0.9 and from 2.9 to 1.4, respectively. The four fluorescence peaks in both LB-EPS and TB-EPS identified by three-dimensional excitation-emission matrix fluorescence spectroscopy are attributed to PN-like substances and humic acid-like substances. The Fourier transform infrared spectra of the LB-EPS and TB-EPS appeared to be very similar, but the differences across the spectra were apparent in terms of the relative intensity of some bands with the increase of salinity. The sludge volume index showed a linear correlation with LB-EPS (R(2)=0.9479) and TB-EPS (R(2)=0.9355) at different salinities, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Small angle x-ray scattering study on the conformation of polystyrene in toluene during adding anti-solvent CO2

NASA Astrophysics Data System (ADS)

Liu, Yi; Chen, Dong-Feng; Wang, Hong-Li; Chen, Na; Li, Dan; Han, Bu-Xing; Rong, Li-Xia; Zhao, Hui; Wang, Jun; Dong, Bao-Zhong

2002-10-01

The conformation of polystyrene in the anti-solvent process of supercritical fluids (compressed CO2 + polystyrene + toluene) has been studied by small angle x-ray scattering with synchrotron radiation as an x-ray source. Coil-to-globule transformation of the polystyrene chain was observed with the increase of the anti-solvent CO2 pressure; i.e. polystyrene coiled at a pressure lower than the cloud point pressure (Pc) and turned into a globule with a uniform density at pressures higher than Pc. Fractal behaviour was also found in the chain contraction and the mass fractal dimension increased with increasing CO2 pressure.

Floating Probe Assembly for Measuring Temperature of Water

NASA Technical Reports Server (NTRS)

Stewart, Randy; Ruffin, Clyde

2002-01-01

A floating apparatus denoted a temperature probe aquatic suspension system (TPASS) has been developed for measuring the temperature of an ocean, lake, or other natural body of water at predetermined depths. Prior instruments built for the same purpose were found to give inaccurate readings because the apparatuses themselves significantly affected the temperatures of the water in their vicinities. The design of the TPASS is intended to satisfy a requirement to minimize the perturbation of the temperatures to be measured. The TPASS includes a square-cross-section aluminum rod 28 in. (=71 cm) long with floats attached at both ends. Each float includes five polystyrene foam disks about 3/4 in.(=1.9 cm) thick and 2.5 in. (=6.4 cm) in diameter. The disks are stacked to form cylinders, bolted to the rod, and covered with hollow plastic sleeves. A metal sleeve is clamped to the middle of the aluminum rod, from whence it hangs down into the water. Temperature probes (which can be thermocouples, thermistors, or resistance temperature devices) are placed within the sleeve at the desired measurement depths. Wires from the temperature probes are routed to the input terminals of a data logger.

Floating Probe Assembly for Measuring Temperature of Water

NASA Technical Reports Server (NTRS)

Selinsky, T.; Stewart, Randy; Ruffin, Clyde

2002-01-01

A floating apparatus denoted a temperature probe aquatic suspension system (TPASS) has been developed for measuring the temperature of an ocean, lake, or other natural body of water at predetermined depths. Prior instruments built for the same purpose were found to give inaccurate readings because the apparatuses themselves significantly affected the temperatures of the water in their vicinities. The design of the TPASS is intended to satisfy a requirement to minimize the perturbation of the temperatures to be measured. The TPASS includes a square-cross-section aluminum rod 28 in. (approx. = 71 cm) long with floats attached at both ends. Each float includes five polystyrene foam disks about 3/4 in. (approx. = 1.9 cm) thick and 2.5 in. (approx. = 6.4 cm) in diameter. The disks are stacked to form cylinders, bolted to the rod, and covered with hollow plastic sleeves. A metal sleeve is clamped to the middle of the aluminum rod, from whence it hangs down into the water. Temperature probes (which can be thermocouples, thermistors, or resistance temperature devices) are placed within the sleeve at the desired measurement depths. Wires from the temperature probes are routed to the input terminals of a data logger. This work was done by Randy

Sensory irritation and incapacitation evoked by thermal decomposition products of polymers and comparisons with known sensory irritants.

PubMed

Barrow, C S; Alarie, Y; Stock, M F

1978-01-01

A decrease in respiratory rate in mice during exposure to irritating airborne chemicals has been utilized as a response parameter to characterize the degree of upper respiratory tract irritation (sensory irritation) to the thermal decomposition products of various polymers. These included polystyrene, polyvinyl chloride, flexible polyurethane foam, polytetrafluorethylene, a fiber glass reinforced polyester resin, and Douglas Fir. Each of the materials was thermally decomposed in a low-mass vertical furnace in an air atmosphere at a programmed heating rate of 20 degrees C/min. Mice, in groups of four, were exposed to graded concentrations of the thermal decomposition products of each of the above materials. Dose-response curves were obtained by utilizing the maximum percent decrease in respiratory rate as the response parameter during each exposure. Comparison of these dose-response curves with other sensory irritants such as chlorine, ammonia, hydrogen chloride, sulfur dioxide, and toluene diisocyanate gave an indication of the sensory irrtation potential of the thermal decomposition products of these various polymers versus that of well-known single airborne chemical irritants. Total stress and incapacitation of the organism during exposure to sensory irritants such as from the thermal decomposition products of synthetic polymers is discussed.

Exploratory investigations of hypervelocity intact capture spectroscopy

NASA Technical Reports Server (NTRS)

Tsou, P.; Griffiths, D. J.

1993-01-01

The ability to capture hypervelocity projectiles intact opens a new technique available for hypervelocity research. A determination of the reactions taking place between the projectile and the capture medium during the process of intact capture is extremely important to an understanding of the intact capture phenomenon, to improving the capture technique, and to developing a theory describing the phenomenon. The intact capture of hypervelocity projectiles by underdense media generates spectra, characteristic of the material species of projectile and capture medium involved. Initial exploratory results into real-time characterization of hypervelocity intact capture techniques by spectroscopy include ultra-violet and visible spectra obtained by use of reflecting gratings, transmitting gratings, and prisms, and recorded by photographic and electronic means. Spectrometry proved to be a valuable real-time diagnostic tool for hypervelocity intact capture events, offering understanding of the interactions of the projectile and the capture medium during the initial period and providing information not obtainable by other characterizations. Preliminary results and analyses of spectra produced by the intact capture of hypervelocity aluminum spheres in polyethylene (PE), polystyrene (PS), and polyurethane (PU) foams are presented. Included are tentative emission species identifications, as well as gray body temperatures produced in the intact capture process.

Gas in scattering media absorption spectroscopy - GASMAS

NASA Astrophysics Data System (ADS)

Svanberg, Sune

2008-09-01

An overview of the new field of Gas in Scattering Media Absorption Spectroscopy (GASMAS) is presented. GASMAS combines narrow-band diode-laser spectroscopy with diffuse media optical propagation. While solids and liquids have broad absorption features, free gas in pores and cavities in the material is characterized by sharp spectral signatures, typically 10,000 times sharper than those of the host material. Many applications in materials science, food packaging, pharmaceutics and medicine have been demonstrated. So far molecular oxygen and water vapour have been studied around 760 and 935 nm, respectively. Liquid water, an important constituent in many natural materials, such as tissue, has a low absorption at such wavelengths, allowing propagation. Polystyrene foam, wood, fruits, food-stuffs, pharmaceutical tablets, and human sinus cavities have been studied. Transport of gas in porous media can readily be studied by first immersing the material in, e.g., pure nitrogen, and then observing the rate at which normal air, containing oxygen, reinvades the material. The conductance of the sinus connective passages can be measured in this way by flushing the nasal cavity with nitrogen. Also other dynamic processes such as drying of materials can be studied. The techniques have also been extended to remote-sensing applications (LIDAR-GASMAS).

"Since both of us are using antiretrovirals, we have been supportive to each other": facilitators and barriers of pre-exposure prophylaxis use in heterosexual HIV serodiscordant couples in Kisumu, Kenya.

PubMed

Patel, Rena C; Stanford-Moore, Gaelen; Odoyo, Josephine; Pyra, Maria; Wakhungu, Imeldah; Anand, Keerthana; Bukusi, Elizabeth A; Baeten, Jared M; Brown, Joelle M

2016-01-01

Since 2015, the World Health Organization recommends pre-exposure prophylaxis (PrEP) for all persons at substantial risk for HIV, including HIV-uninfected partners in serodiscordant relationships in resource-limited settings. As PrEP moves from clinical trials to real-world use, understanding facilitators of and barriers to PrEP initiation and adherence is critical to successful PrEP implementation and rollout. We conducted 44 in-depth individual or couple interviews with 63 participants (30 without HIV and 33 with HIV) enrolled in the Partners Demonstration Project in Kisumu, Kenya, between August and September 2014. The semi-structured interviews discussed the following: 1) perceived advantages and disadvantages of antiretroviral therapy (ART)/PrEP; 2) reasons for accepting or declining ART/PrEP and 3) influence of prevention of transmission to partner or infant on ART/PrEP use. Transcripts from the interviews were iteratively analyzed using inductive content analysis. Our study identified three key factors that may facilitate initiation of PrEP in this population. First, participants using PrEP felt reduced stress and increased trust in their HIV serodiscordant relationships. Second, greater community-wide knowledge of PrEP was thought to likely increase PrEP acceptance. Third, greater education and counselling by providers on PrEP use was also considered to likely increase the adoption of PrEP. We also identified three key barriers to initiation of and adherence to PrEP. First, most participants who declined PrEP expressed doubts about the relative additional effectiveness of PrEP in combination with other prevention tools. Second, perceived stigma related to PrEP use was an important barrier to PrEP initiation. Third, many struggled with overcoming perceived side effects or logistical challenges of taking daily PrEP, particularly when they themselves were not ill. Leveraging the facilitators and overcoming barriers to PrEP uptake may enhance the successful rollout of PrEP among HIV serodiscordant couples in Kenya and other areas in sub-Saharan Africa, thereby reducing sexual transmission of HIV. Further research focused on how best to provide counselling on combination HIV prevention tools in the context of PrEP use is a crucial next step to delivering PrEP.

Monitoring multiple sclerosis by multimodal evoked potentials: Numerically versus ordinally scaled scoring systems.

PubMed

Schlaeger, Regina; Hardmeier, Martin; D'Souza, Marcus; Grize, Leticia; Schindler, Christian; Kappos, Ludwig; Fuhr, Peter

2016-03-01

To compare the ability of different evoked potential scores (EPS) to monitor and predict the disease course in multiple sclerosis (MS). Seventy-two patients with MS or clinically isolated syndrome were investigated by visual, motor, and somatosensory EP and expanded disability status scale (EDSS) at baseline (T0) and months 6, 12, 24, 36 (T4). EP results were rated according to ordinal (o), semi-quantitative (sq), and quantitative (q) EPS. Spearman rank correlation and multivariable linear regression were used to investigate the associations between EPS and clinical disability. All EPS correlated with EDSS cross-sectionally (0.72⩽rho⩽0.87, all p<0.001) and longitudinally (0.39⩽rho⩽0.47, all p⩽0.004). EPS(T0) and EDSS(T0) together explained 85-86% of EDSS(T4) variance. A posteriori power calculation showed that the sample sizes needed to detect significant changes over 6 months in q-EPS, sq-EPS and o-EPS with 90% certainty would be 50, 129 and 222, respectively. q-EPS change(T1-T0) correlated with EDSS change(T4-T0) (rho=0.56, p<0.001), while sq-EPS and o-EPS changes(T1-T0) did not. All three EPS allow disease course monitoring in MS. However, the quantitative EPS detects clinically relevant short-term changes with a smaller sample size than semi-quantitative or ordinal EPS. These results underscore the potential of EPS to characterize MS disease evolution. Copyright © 2016. Published by Elsevier Ireland Ltd.

Impact of ethyl pyruvate on Adriamycin-induced cardiomyopathy in rats

PubMed Central

Liu, Menglin; Wang, Menglong; Liu, Jianfang; Luo, Zhen; Shi, Lei; Feng, Ying; Li, Li; Xu, Lin; Wan, Jun

2016-01-01

Ethyl pyruvate (EP), a derivative of pyruvic acid, is known to have protective effects against ischemic cardiomyopathy and other disorders. However, little is known about its role in Adriamycin (ADR)-induced cardiomyopathy. The present study was designed to investigate the impact of EP on ADR-induced cardiomyopathy in an animal model. Sixty male Sprague-Dawley (SD) rats were divided into four groups: Normal control, EP, ADR and ADR + EP groups (n=15/group). Rats in the ADR and ADR + EP groups were treated with ADR (2.5 mg/kg/week intraperitoneally) for 6 weeks. From the eighth week, rats in the EP and ADR + EP groups received EP via gastric lavage at a dose of 50 mg/kg/day for 30 days. After completing the EP treatment, cardiac function was assessed by echocardiography and then rats were sacrificed. Hearts were harvested for subsequent analysis. Compared with rats in the normal control and EP groups (without ADR treatment), rats in the ADR and ADR + EP groups showed significant impairments in terms of cardiac function, apoptosis, severe oxidative stress and fibrosis in the heart. However, these impairments were alleviated by EP treatment in the ADR + EP group. Upon EP treatment, cardiac function was significantly improved. The levels of oxidative stress, fibrosis and apoptosis in the myocardial tissues were also significantly reduced. These findings indicated that EP treatment attenuated, at least partially, ADR-induced cardiomyopathy in rats. PMID:27882138

Optimizing content for pre-exposure prophylaxis (PrEP) counseling for men who have sex with men: Perspectives of PrEP users and high-risk PrEP naïve men.

PubMed

Wade Taylor, S; Mayer, Kenneth H; Elsesser, Steven M; Mimiaga, Matthew J; O'Cleirigh, Conall; Safren, Steven A

2014-05-01

Existing trials of antiretroviral (ARV) medication as chemoprophylaxis against HIV reveal that the degree of protection is primarily dependent on product adherence. However, there is a lack of data on targets for behavioral interventions to improve adherence to ARV as prevention. Information from individuals who have used ARV as pre-exposure prophylaxis (PrEP) can inform behavioral intervention development. Thirty-nine HIV-uninfected MSM at high risk for HIV acquisition participated in one of four semi-structured focus groups. Two of the focus groups consisted of MSM who had been prescribed and used PrEP in the context of a clinical trial; the other two consisted of high-risk MSM who had not previously used PrEP. An in-depth, within-case/across-case content analysis resulted in six descriptive themes potentially salient for a PrEP adherence behavioral intervention: (1) motivations to use PrEP, (2) barriers to PrEP use, (3) facilitators to PrEP use, (4) sexual decision-making in the context of PrEP, (5) prospective PrEP education content, and, (6) perceived effective characteristics of PrEP delivery personnel. Addressing these themes in behavioral interventions in the context of prescribing PrEP may result in the optimal "packaging" public health programs that implement PrEP for high-risk MSM.

Positive and negative impacts of specialty malts on beer foam: a comparison of various cereal products for their foaming properties.

PubMed

Combe, Alexander L; Ang, Justin K; Bamforth, Charles W

2013-07-01

The foam stability of beer is dependent on the presence of foam-stabilizing polypeptides derived from the cereals from which it is made. It has long been argued that there is a tendency to boost the foam-stabilizing capabilities of these polypeptides at the heating stages involved in the production of the grist materials. The present study started with the intent to confirm whether these changes occurred and to assess the extent to which different cereal products differed in their foam-stabilizing tendencies. Cereal products differ enormously in their foam-stabilizing capabilities. Heavily roasted grains, notably black malt and roast barley, do have superior foaming properties. However, certain specialty malts, notably crystal malts, display inferior foam performance. The observed foaming pattern is a balance between their content of foam-positive and foam-negative components. Products such as pale malt do contain foam-negative materials but have a net balance in favour of foam-stabilizing entities. By contrast, wheat malt and especially black malt have a heavy preponderance of foam-positive components. Crystal malt displays the converse behaviour: it contains low-molecular-weight foam-negative species. Several of the cereal products appear to contain higher-molecular-weight foam inhibitors, but it appears that they are merely species that are of inherently inferior foam-stabilizing capability to the foaming polypeptides from egg white that were employed to probe the system. The foam-damaging species derived from crystal malt carried through to beers brewed from them. Intense heating in the production of cereal products does lead to enhanced foam performance in extracts of those products. However, not all speciality malts display superior foam performance, through their development of foam-negative species of lower molecular weight. © 2013 Society of Chemical Industry.

High-power, kilojoule laser interactions with near-critical density plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Willingale, L.; Thomas, A. G. R.; Maksimchuk, A.

Experiments were performed using the Omega EP laser, which provided pulses containing 1kJ of energy in 9ps and was used to investigate high-power, relativistic intensity laser interactions with near-critical density plasmas, created from foam targets with densities of 3-100 mg/cm{sup 3}. The effect of changing the plasma density on both the laser light transmitted through the targets and the proton beam accelerated from the interaction was investigated. Two-dimensional particle-in-cell simulations enabled the interaction dynamics and laser propagation to be studied in detail. The effect of the laser polarization and intensity in the two-dimensional simulations on the channel formation and electronmore » heating are discussed. In this regime, where the plasma density is above the critical density, but below the relativistic critical density, the channel formation speed and therefore length are inversely proportional to the plasma density, which is faster than the hole boring model prediction. A general model is developed to describe the channel length in this regime.« less

Functional Knowledge of Pre-Exposure Prophylaxis for HIV Prevention Among Participants in a Web-Based Survey of Sexually Active Gay, Bisexual, and Other Men Who Have Sex With Men: Cross-Sectional Study

PubMed Central

2018-01-01

Background Awareness of pre-exposure prophylaxis (PrEP) for HIV prevention is increasing, but little is known about the functional knowledge of PrEP and its impact on willingness to use PrEP. Objective The objective of this study was to assess the functional knowledge of PrEP among a sample of gay, bisexual, and other men who have sex with men (MSM) participating in a Web-based survey of sexually active MSM. Methods Men at least 18 years old, residing in the United States, and reporting sex with a man in the previous 6 months were recruited through social networking websites. PrEP functional knowledge included the following 4 questions (1) efficacy of consistent PrEP use, (2) inconsistent PrEP use and effectiveness, (3) PrEP and condom use, and (4) effectiveness at reducing sexually transmitted infections (STIs). Ordinal logistic regression was used to identify respondent characteristics associated with PrEP functional knowledge. In a subsample of participants responding to HIV prevention questions, we compared willingness to use PrEP by response to PrEP functional knowledge using logistic regression analysis adjusted for age, race and ethnicity, and education level. Results Among 573 respondents, PrEP knowledge was high regarding adherence (488/573, 85.2%), condom use (532/573, 92.8%), and STIs (480/573, 83.8%), but only 252/573 (44.0%) identified the correct efficacy. Lower functional PrEP knowledge was associated with minority race/ethnicity (P=.005), lower education (P=.01), and not having an HIV test in the past year (P=.02). Higher PrEP knowledge was associated with willingness to use PrEP (P=.009). Younger age was not associated with higher PrEP functional knowledge or willingness to use PrEP. Conclusions PrEP knowledge was generally high in our study, including condom use and consistent use but may be lacking in higher risk MSM. The majority of respondents did not correctly identify PrEP efficacy with consistent use, which could impact motivation to seek out PrEP for HIV prevention. Targeted messaging to increase PrEP knowledge may increase PrEP use. PMID:29362213

Considerations for the Use of Exterior Insulation & Finish Systems (EIFS) on U.S. Army Facilities

DTIC Science & Technology

1991-11-01

Typical kinds of insulation used in EIFS include molded expanded polystyrene (MEPS), extruded expanded polystyrene (XEPS), semi-rigid fiberglass, and...Extruded expanded polystyrene insulation, see XEPS 85 Finish coat 12-17, 20, 22-24, 26 degradation 32, 61, 68, 71, 78 Impact damage 28, 56, 83 resistance 15...lath 12, 15, 16, 20, 25, 74 Mildew 14, 78 Molded expanded polystyrene insulation, see MEPS Notched trowel application 19, 74 Portland cement 13, 15-17

Characteristics of extracellular polymeric substances from sludge and biofilm in a simultaneous nitrification and denitrification system under high salinity stress.

PubMed

Zhao, Linting; She, Zonglian; Jin, Chunji; Yang, Shiying; Guo, Liang; Zhao, Yangguo; Gao, Mengchun

2016-09-01

The composition and distribution of extracellular polymeric substance (EPS) both from suspended sludge and attached biofilm were investigated in a simultaneous nitrification and denitrification (SND) system with the increase of the salinity from 1.0 to 3.0 %. Fourier-transform infrared (FTIR) spectroscopy and three-dimensional excitation-emission matrix (3D-EEM) fluorescence spectroscopy were used to examine proteins (PN), polysaccharides (PS) and humic substances (HS) present in EPS. High total nitrogen removal (above 83.9 %) via SND was obtained in the salinity range of 1.0-2.5 %. Total EPS in the sludge increased from 150.2 to 200.6 mg/gVSS with the increase of salinity from 1.0 to 3.0 %, whereas the corresponding values in the biofilm achieved the maximum of 288.6 mg/g VSS at 2.0 % salinity. Dominant composition of EPS was detected as HS in both sludge and biofilm, having the percentages of 50.6-68.6 and 41.1-69.9 % in total EPS, respectively. Both PN and PS contents in soluble EPS (S-EPS), loosely bound EPS (LB-EPS) and tightly bound EPS (TB-EPS) of sludge and biofilm increased with the increased salinity. The FTIR spectrum and 3D-EEM fluorescence spectroscopy of S-EPS, LB-EPS and TB-EPS in the sludge and biofilm showed the changes of functional groups and conformations of the compositions in EPS with the increase of salinity. The results demonstrated that the characteristics of EPS varied from sludge to biofilm. The obtained results could provide a better understanding of the salinity effect on the EPS characteristics in a SND system.

Young Transgender Women's Attitudes Toward HIV Pre-exposure Prophylaxis.

PubMed

Wood, Sarah M; Lee, Susan; Barg, Frances K; Castillo, Marne; Dowshen, Nadia

2017-05-01

Our primary aim was to explore themes regarding attitudes toward HIV pre-exposure prophylaxis (PrEP) among young transgender women (YTW), in order to develop a theoretical model of PrEP uptake in this population disproportionally affected by HIV. Qualitative study nested within a mixed-method study characterizing barriers and facilitators to health services for YTW. Participants completed an in-depth interview exploring awareness of and attitudes toward PrEP. Key themes were identified using a grounded theory approach. Participants (n = 25) had a mean age of 21.2 years (standard deviation 2.2, range 17-24) and were predominately multiracial (36%) and of HIV-negative or unknown status (68%). Most participants (64%) reported prior knowledge of PrEP, and 28% reported current use or intent to use PrEP. Three major content themes that emerged were variability of PrEP awareness, barriers and facilitators to PrEP uptake, and emotional benefits of PrEP. Among participants without prior PrEP knowledge, participants reported frustration that PrEP information has not been widely disseminated to YTW, particularly by health care providers. Attitudes toward PrEP were overwhelmingly positive; however, concerns were raised regarding barriers including cost, stigma, and adherence challenges. Both HIV-positive and negative participants discussed emotional and relationship benefits of PrEP, which were felt to extend beyond HIV prevention alone. A high proportion of YTW in this study had prior knowledge of PrEP, and attitudes toward PrEP were positive among participants. Our findings suggest several domains to be further explored in PrEP implementation research, including methods of facilitating PrEP dissemination and emotional motivation for PrEP uptake. Copyright © 2016 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

Dietary assimilation of cadmium associated with bacterial exopolymer sediment coatings by the estuarine amphipod Leptocheirus plumulosus: Effects of Cd concentration and salinity

USGS Publications Warehouse

Schlekat, C.E.; Decho, Alan W.; Chandler, G.T.

1999-01-01

Bacterial extracellular substances (also known as exopolysaccharides, or EPS) may serve as vectors for trophic transfer of metals in benthic systems because these ubiquitous sediment coatings can sorb high concentrations of toxic metals, and because many benthic invertebrates assimilate EPS sediment coatings upon ingestion. We conducted 3 sets of experiments to determine the assimilative bioavailability of EPS-associated Cd to the benthic amphipod Leptocheirus plumulosus as a function of Cd concentration and salinity. Bioavailability was measured as L. plumulosus Cd assimilation efficiency (AE) from EPS-coated silica (EPS-Si) and from uncoated silica (NC-Si) using modified pulse-chase methods with the gamma-emitting radioisotope 109Cd. Cd AE was significantly greater from NC-Si than from EPS-Si at 7.5???, but not at 2.5 or 25???. Overall, Cd AE from EPS-Si was between 15.1 and 21.5%. Because EPS-Si sorbed more Cd than NC-Si, EPS coatings magnified the amount of Cd amphipods accumulated at each salinity by up to a factor of 10. Salinity did not directly affect Cd AE from EPS-Si, but because Cd-EPS partitioning increased with decreasing salinity, amphipods accumulated more Cd from EPS at the lowest Cd-EPS incubation salinity (2.5 ???) than at higher salinities (7.5 and 25 ???). Finally, Cd concentration in EPS exhibited an inverse relationship with Cd AE at 2.5 ???, but not at 25 ???. Specifically, Cd AE was 12 times greater at 1 compared with 10 ??g Cd ??g-1 EPS. Together, these results show that estuarine benthos can accumulate Cd from EPS sediment coatings, but that the degree to which this phenomenon occurs is dependent upon seawater salinity and Cd concentration in EPS.

PrEP awareness and decision-making for Latino MSM in San Antonio, Texas

PubMed Central

García, Moctezuma; Harris, Allyssa L.

2017-01-01

Pre-Exposure Prophylaxis (PrEP) has been promoted among high-risk populations as an effective HIV biomedical intervention. However, limited research is available on the significance of culturally informed biomedical interventions for Latino MSM. A total of 159 self-administered Internet surveys were completed by Latino MSM ages 21–30 in San Antonio, Texas. The purpose of this research was to develop an instrument that measured Latino MSM attitudes and beliefs towards PrEP, identify associations between demographic factors and PrEP related factors and to suggest culturally appropriate strategies for the promotion of PrEP among the Latino MSM population. Research findings revealed implications for PrEP at the structural and individual level for Latino MSM. Structural level indicators emphasized the importance for raising PrEP awareness among Latino MSM in regards to PrEP related expenses, ameliorating stigmatization of high-risk populations, enhancing access to PrEP informed medical providers, and address mistrust of the government and medical providers role on addressing health disparities among Latino MSM. Overall, the findings for individual factors emphasize the need for patient-centered interventions for Latino MSM. Latino MSM currently on PrEP require supplemental resources to enhance PrEP adherence. Latino MSM not on PrEP require alternate options for PrEP delivery and/or cognitive behavioral approaches minimizing HIV risk behavior for Latino MSM concerned with PrEP toxicity, which may require non-biomedical interventions. Integration of Latino MSM currently on PrEP as peer educators provides a valuable resource for developing culturally informed PrEP interventions for Latino MSM. Peer educators are able to share their experiential knowledge of PrEP contextualized through cultural norms, beliefs, and values. PMID:28953905

EpCAM and the biology of hepatic stem/progenitor cells

PubMed Central

Theise, Neil D.; Schmelzer, Eva; Boulter, Luke; Gires, Olivier; van Grunsven, Leo A.

2014-01-01

Epithelial cell adhesion molecule (EpCAM) is a transmembrane glycoprotein, which is frequently and highly expressed on carcinomas, tumor-initiating cells, selected tissue progenitors, and embryonic and adult stem cells. During liver development, EpCAM demonstrates a dynamic expression, since it can be detected in fetal liver, including cells of the parenchyma, whereas mature hepatocytes are devoid of EpCAM. Liver regeneration is associated with a population of EpCAM-positive cells within ductular reactions, which gradually lose the expression of EpCAM along with maturation into hepatocytes. EpCAM can be switched on and off through a wide panel of strategies to fine-tune EpCAM-dependent functional and differentiative traits. EpCAM-associated functions relate to cell–cell adhesion, proliferation, maintenance of a pluripotent state, regulation of differentiation, migration, and invasion. These functions can be conferred by the full-length protein and/or EpCAM-derived fragments, which are generated upon regulated intramembrane proteolysis. Control by EpCAM therefore not only depends on the presence of full-length EpCAM at cellular membranes but also on varying rates of the formation of EpCAM-derived fragments that have their own regulatory properties and on changes in the association of EpCAM with interaction partners. Thus spatiotemporal localization of EpCAM in immature liver progenitors, transit-amplifying cells, and mature liver cells will decisively impact the regulation of EpCAM functions and might be one of the triggers that contributes to the adaptive processes in stem/progenitor cell lineages. This review will summarize EpCAM-related molecular events and how they relate to hepatobiliary differentiation and regeneration. PMID:25477371

State-of-the-Art Review on the Characteristics of Surfactants and Foam from Foam Concrete Perspective

NASA Astrophysics Data System (ADS)

Sahu, Sritam Swapnadarshi; Gandhi, Indu Siva Ranjani; Khwairakpam, Selija

2018-06-01

Foam concrete finds application in many areas, generally as a function of its relatively lightweight and its beneficial properties in terms of reduction in dead load on structure, excellent thermal insulation and contribution to energy conservation. For production of foam concrete with desired properties, stable and good quality foam is the key requirement. It is to be noted that the selection of surfactant and foam production parameters play a vital role in the properties of foam which in turn affects the properties of foam concrete. However, the literature available on the influence of characteristics of foaming agent and foam on the properties of foam concrete are rather limited. Hence, a more systematic research is needed in this direction. The focus of this work is to provide a review on characteristics of surfactant (foaming agent) and foam for use in foam concrete production.

State-of-the-Art Review on the Characteristics of Surfactants and Foam from Foam Concrete Perspective

NASA Astrophysics Data System (ADS)

Sahu, Sritam Swapnadarshi; Gandhi, Indu Siva Ranjani; Khwairakpam, Selija

2018-02-01

Foam concrete finds application in many areas, generally as a function of its relatively lightweight and its beneficial properties in terms of reduction in dead load on structure, excellent thermal insulation and contribution to energy conservation. For production of foam concrete with desired properties, stable and good quality foam is the key requirement. It is to be noted that the selection of surfactant and foam production parameters play a vital role in the properties of foam which in turn affects the properties of foam concrete. However, the literature available on the influence of characteristics of foaming agent and foam on the properties of foam concrete are rather limited. Hence, a more systematic research is needed in this direction. The focus of this work is to provide a review on characteristics of surfactant (foaming agent) and foam for use in foam concrete production.

Polystyrene microplastics induce microbiota dysbiosis and inflammation in the gut of adult zebrafish.

PubMed

Jin, Yuanxiang; Xia, Jizhou; Pan, Zihong; Yang, Jiajing; Wang, Wenchao; Fu, Zhengwei

2018-04-01

Microplastic (MP) are environmental pollutants and have the potential to cause varying degrees of aquatic toxicity. In this study, the effects on gut microbiota of adult male zebrafish exposed for 14 days to 100 and 1000 μg/L of two sizes of polystyrene MP were evaluated. Both 0.5 and 50 μm-diameter spherical polystyrene MP increased the volume of mucus in the gut at a concentration of 1000 μg/L (about 1.456 × 10 10 particles/L for 0.5 μm and 1.456 × 10 4 particles/L for 50 μm). At the phylum level, the abundance of Bacteroidetes and Proteobacteria decreased significantly and the abundance of Firmicutes increased significantly in the gut after 14-day exposure to 1000 μg/L of both sizes of polystyrene MP. In addition, high throughput sequencing of the 16S rRNA gene V3-V4 region revealed a significant change in the richness and diversity of microbiota in the gut of polystyrene MP-exposed zebrafish. A more in depth analysis, at the genus level, revealed that a total of 29 gut microbes identified by operational taxonomic unit (OTU) analysis were significantly changed in both 0.5 and 50 μm-diameter polystyrene MP-treated groups. Moreover, it was observed that 0.5 μm polystyrene MP not only increased mRNA levels of IL1α, IL1β and IFN but also their protein levels in the gut, indicating that inflammation occurred after polystyrene MP exposure. Our findings suggest that polystyrene MP could induce microbiota dysbiosis and inflammation in the gut of adult zebrafish. Copyright © 2017 Elsevier Ltd. All rights reserved.

Solvent effect on polystyrene surface roughness on top of QCM sensor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sakti, Setyawan P., E-mail: sakti@ub.ac.id; Rahmawati, Eka; Robiandi, Fadli

2016-03-11

Quartz Crystal Microbalance (QCM) has been used as a basis for many chemical sensors and biosensor. Its sensitivity to mass change which can detect a mass change on its surface down to sub ng/cm2 is one of its interesting aspects. Another interesting feature is its ability to work in liquid environment. However, there are many aspects which influence QCM sensor properties in contact with liquid. One of the aspects is surface roughness of the matrix layer where on top of it a biological sensitive layer will be immobilized. One of matrix layers in the immobilizing biological sensitive layer was polystyrene.more » Polystyrene was coated on the QCM sensor by using the spin coating method. During the coating process, polystyrene was solved using non-polar solvent. It is known that the physical and chemical properties of the solvent affect a transition process from soluble polymer becoming rigid polymer layer. In this work, we show that polystyrene solved in chloroform has a higher surface roughness compare to one solved in toluene, xylene, or tetrahydrofuran. Surface roughness of the polystyrene coating were measured using a non-contact profilometer. However, we also found that there is no difference on the electrical impedance of the QCM sensor coated with polystyrene resulted from differing solvent when the sensor was in contact with air and water. Thus, all of the mentioned solvent can be used to solve the polystyrene as a coating material for QCM sensor without affecting the electrical performance of the sensor, but the choice of the solution can be used as a simple method to control the difference roughness of the polystyrene coating.« less

Solvent effect on polystyrene surface roughness on top of QCM sensor

NASA Astrophysics Data System (ADS)

Sakti, Setyawan P.; Rahmawati, Eka; Robiandi, Fadli

2016-03-01

Quartz Crystal Microbalance (QCM) has been used as a basis for many chemical sensors and biosensor. Its sensitivity to mass change which can detect a mass change on its surface down to sub ng/cm2 is one of its interesting aspects. Another interesting feature is its ability to work in liquid environment. However, there are many aspects which influence QCM sensor properties in contact with liquid. One of the aspects is surface roughness of the matrix layer where on top of it a biological sensitive layer will be immobilized. One of matrix layers in the immobilizing biological sensitive layer was polystyrene. Polystyrene was coated on the QCM sensor by using the spin coating method. During the coating process, polystyrene was solved using non-polar solvent. It is known that the physical and chemical properties of the solvent affect a transition process from soluble polymer becoming rigid polymer layer. In this work, we show that polystyrene solved in chloroform has a higher surface roughness compare to one solved in toluene, xylene, or tetrahydrofuran. Surface roughness of the polystyrene coating were measured using a non-contact profilometer. However, we also found that there is no difference on the electrical impedance of the QCM sensor coated with polystyrene resulted from differing solvent when the sensor was in contact with air and water. Thus, all of the mentioned solvent can be used to solve the polystyrene as a coating material for QCM sensor without affecting the electrical performance of the sensor, but the choice of the solution can be used as a simple method to control the difference roughness of the polystyrene coating.

Experimental Study of Hysteresis behavior of Foam Generation in Porous Media.

PubMed

Kahrobaei, S; Vincent-Bonnieu, S; Farajzadeh, R

2017-08-21

Foam can be used for gas mobility control in different subsurface applications. The success of foam-injection process depends on foam-generation and propagation rate inside the porous medium. In some cases, foam properties depend on the history of the flow or concentration of the surfactant, i.e., the hysteresis effect. Foam may show hysteresis behavior by exhibiting multiple states at the same injection conditions, where coarse-textured foam is converted into strong foam with fine texture at a critical injection velocity or pressure gradient. This study aims to investigate the effects of injection velocity and surfactant concentration on foam generation and hysteresis behavior as a function of foam quality. We find that the transition from coarse-foam to strong-foam (i.e., the minimum pressure gradient for foam generation) is almost independent of flowrate, surfactant concentration, and foam quality. Moreover, the hysteresis behavior in foam generation occurs only at high-quality regimes and when the pressure gradient is below a certain value regardless of the total flow rate and surfactant concentration. We also observe that the rheological behavior of foam is strongly dependent on liquid velocity.

Motives of Dutch men who have sex with men for daily and intermittent HIV pre-exposure prophylaxis usage and preferences for implementation: A qualitative study.

PubMed

Bil, Janneke P; van der Veldt, Wendy M; Prins, Maria; Stolte, Ineke G; Davidovich, Udi

2016-09-01

Although PrEP is not yet registered in Europe, including the Netherlands, its approval and implementation are expected in the near future. To inform future pre-exposure prophylaxis (PrEP) implementation, this study aimed to gain insight into motives and preferences for daily or intermittent PrEP use among Dutch HIV-negative men having sex with men (MSM).Between February and December 2013, semistructured interviews were conducted until data saturation was reached (N = 20). Interviews were analyzed using the Grounded Theory approach.Motives for (not) using daily PrEP were based on beliefs about PrEP efficacy and side effects, preferences for other prevention strategies, self-perceived HIV risk, self-perceived efficacy of PrEP adherence, beliefs about possible benefits (e.g., anxiety reduction, sex life improvement), and barriers of PrEP use (e.g., costs, monitoring procedures). The perceived benefits of intermittent versus daily PrEP use were the lower costs and side effects and the lower threshold to decision to start using intermittent PrEP. Barriers of intermittent PrEP versus daily PrEP use were the perceived need to plan their sex life and adhere to multiple prevention strategies. Although some perceived PrEP as a condom substitute, others were likely to combine PrEP and condoms for sexually transmitted infections (STI) prevention and increased HIV protection. Participants preferred PrEP service locations to have specialized knowledge of HIV, antiretroviral therapy, sexual behavior, STIs, patients' medical background, be easily approachable, be able to perform PrEP follow-up monitoring, and provide support.To maximize the public health impact of PrEP, ensuring high uptake among MSM at highest risk is important. Therefore, targeted information about PrEP efficacy and side effects need to be developed, barriers for accessing PrEP services should be minimized, and perceived self-efficacy to use PrEP should be addressed and improved. To prevent increases in STIs, condom use should be monitored and PrEP should be integrated into routine STI screening and counseling.

Motives of Dutch men who have sex with men for daily and intermittent HIV pre-exposure prophylaxis usage and preferences for implementation

PubMed Central

Bil, Janneke P.; van der Veldt, Wendy M.; Prins, Maria; Stolte, Ineke G.; Davidovich, Udi

2016-01-01

Abstract Although PrEP is not yet registered in Europe, including the Netherlands, its approval and implementation are expected in the near future. To inform future pre-exposure prophylaxis (PrEP) implementation, this study aimed to gain insight into motives and preferences for daily or intermittent PrEP use among Dutch HIV-negative men having sex with men (MSM). Between February and December 2013, semistructured interviews were conducted until data saturation was reached (N = 20). Interviews were analyzed using the Grounded Theory approach. Motives for (not) using daily PrEP were based on beliefs about PrEP efficacy and side effects, preferences for other prevention strategies, self-perceived HIV risk, self-perceived efficacy of PrEP adherence, beliefs about possible benefits (e.g., anxiety reduction, sex life improvement), and barriers of PrEP use (e.g., costs, monitoring procedures). The perceived benefits of intermittent versus daily PrEP use were the lower costs and side effects and the lower threshold to decision to start using intermittent PrEP. Barriers of intermittent PrEP versus daily PrEP use were the perceived need to plan their sex life and adhere to multiple prevention strategies. Although some perceived PrEP as a condom substitute, others were likely to combine PrEP and condoms for sexually transmitted infections (STI) prevention and increased HIV protection. Participants preferred PrEP service locations to have specialized knowledge of HIV, antiretroviral therapy, sexual behavior, STIs, patients’ medical background, be easily approachable, be able to perform PrEP follow-up monitoring, and provide support. To maximize the public health impact of PrEP, ensuring high uptake among MSM at highest risk is important. Therefore, targeted information about PrEP efficacy and side effects need to be developed, barriers for accessing PrEP services should be minimized, and perceived self-efficacy to use PrEP should be addressed and improved. To prevent increases in STIs, condom use should be monitored and PrEP should be integrated into routine STI screening and counseling. PMID:27684827

Demographic Differences in PrEP-Related Stereotypes: Implications for Implementation.

PubMed

Golub, Sarit A; Gamarel, Kristi E; Surace, Anthony

2017-05-01

Qualitative interviews about pre-exposure prophylaxis (PrEP) stereotypes were conducted with a subsample of 160 MSM who participated in a PrEP messaging study. Negative stereotypes about PrEP users were identified by 80 % of participants. Two types of stereotypes were most common: PrEP users are HIV-infected (and lying about it), and PrEP users are promiscuous and resistant to condom use. Participants' identification of these stereotype categories differed significantly by demographic factors (i.e., race/ethnicity, education). Expanding access to PrEP requires recognizing potential differences in the experience or anticipation of PrEP-related stereotypes that might impact willingness to discuss PrEP with providers, friends, or partners.

Modeling Study: Mechanism of Foam Propagation in Porous Media at Different Levels of Minimum Mobilization Pressure Gradient

NASA Astrophysics Data System (ADS)

Izadi, M.; Kam, S.

2017-12-01

Scope: Numerous laboratory and field tests revealed that foam can effectively control gas mobility and improve sweep efficiency in enhanced-oil-recovery and subsurface-remediation processes, if correctly designed. The objective of this study is to answer (i) how mechanistic foam model parameters can be determined by fitting lab experiments in a step-by-step manner; (ii) how different levels of mobilization pressure gradient for foam generation affects the fundamentals of foam propagation; and (iii) how foam propagation distance can be estimated in the subsurface. This study for the first time shows why, and by how much, supercritical CO2 foams are advantaged over other types of foams such as N2 foam. Methods: First of all, by borrowing experimental data existing in the literature, this study shows how to capture mechanistic foam model parameters. The model, then, is applied to a wide range of mobilization pressure gradient to represent different types of foams that have been applied in the field (Note that supercritical CO2 foams exhibit much lower mobilization pressure compared to other types of foams (N2, steam, air, etc.). Finally, the model and parameters are used to evaluate different types of foam injection scenarios in order to predict how far foams can propagate with what properties in the field condition. Results and Conclusions: The results show that (i) the presence of three different foam states (strong, weak, intermediate) as well as two different strong-foam flow regimes (high-quality and low-quality regimes) plays a key role in model fit and field-scale propagation prediction and (ii) the importance of complex non-Newtonian foam rheology should not be underestimated. More specifically, this study finds that (i) supercritical CO2 foams can propagate a few hundreds of feet easily, which is a few orders of magnitude higher than other foams such as N2 foams; (ii) for dry foams (or, strong foams in the high-quality regime), the higher gas fractions the less foams travel, while for wet foams (or, strong foams in the low-quality regime) the distance is not sensitive to gas fraction; and (iii) the higher injection rates (or pressures), the farther foams propagate (this effect is much more pronounced for dry foams).

Serotyping of Actinobacillus pleuropneumoniae serotype 5 strains using a monoclonal-based polystyrene agglutination test.

PubMed Central

Dubreuil, J D; Letellier, A; Stenbaek, E; Gottschalk, M

1996-01-01

A polystyrene agglutination test has been developed for serotyping Actinobacillus pleuropneumoniae serotype 5a and 5b strains. Protein A-coated polystyrene microparticles were sensitized with a murine monoclonal antibody recognizing an epitope on serotype 5 LPS-O chain as shown by SDS-PAGE and Western blotting. A total of 205 A. pleuropneumoniae, strains including all 12 serotype reference strains and 13 strains representing 8 common bacterial species associated with swine or related to A. pleuropneumoniae, were tested by mixing 25 microL of polystyrene reagent with the same volume of a dense suspension of bacterial cells grown for 18 h. All A. pleuropneumoniae strains had been previously serotyped using standard procedures. The polystyrene agglutination test was rapid (less than 3 min) and easy to perform. Overall a very good correlation (97.3%) with the standard techniques was found. The sensitized polystyrene particles were stable for at least 6 mo. Images Figure 1. PMID:8825998

Characterisation of recycled acrylonitrile-butadiene-styrene and high-impact polystyrene from waste computer equipment in Brazil.

PubMed

Hirayama, Denise; Saron, Clodoaldo

2015-06-01

Polymeric materials constitute a considerable fraction of waste computer equipment and polymers acrylonitrile-butadiene-styrene and high-impact polystyrene are the main thermoplastic polymeric components found in waste computer equipment. Identification, separation and characterisation of additives present in acrylonitrile-butadiene-styrene and high-impact polystyrene are fundamental procedures to mechanical recycling of these polymers. The aim of this study was to evaluate the methods for identification of acrylonitrile-butadiene-styrene and high-impact polystyrene from waste computer equipment in Brazil, as well as their potential for mechanical recycling. The imprecise utilisation of symbols for identification of the polymers and the presence of additives containing toxic elements in determinate computer devices are some of the difficulties found for recycling of acrylonitrile-butadiene-styrene and high-impact polystyrene from waste computer equipment. However, the considerable performance of mechanical properties of the recycled acrylonitrile-butadiene-styrene and high-impact polystyrene when compared with the virgin materials confirms the potential for mechanical recycling of these polymers. © The Author(s) 2015.

Field efficacy of expanded polystyrene and shredded waste polystyrene beads for mosquito control in artificial pools and field trials, Islamic Republic of Iran.

PubMed

Soltani, A; Vatandoost, H; Jabbari, H; Mesdaghinia, A R; Mahvi, A H; Younesian, M; Hanafi-Bojd, A A; Bozorgzadeh, S

2012-10-01

Concerns about traditional chemical pesticides has led to increasing research into novel mosquito control methods. This study compared the effectiveness of 2 different types of polystyrene beads for control of mosquito larvae in south-east Islamic Republic of Iran. Simulated field trials were done in artificial pools and field trials were carried out in 2 villages in an indigenous malaria area using WHO-recommended methods. Application of expanded polystyrene beads or shredded, waste polystyrene chips to pool surfaces produced a significant difference between pre-treatment and post-treatment density of mosquitoes (86% and 78% reduction respectively 2 weeks after treatment). There was no significant difference between the efficacy of the 2 types of material. The use of polystyrene beads as a component of integrated vector management with other supportive measures could assist in the control of mosquito-borne diseases in the Islamic Republic of Iran and neighbouring countries.

Evaluating filterability of different types of sludge by statistical analysis: The role of key organic compounds in extracellular polymeric substances.

PubMed

Xiao, Keke; Chen, Yun; Jiang, Xie; Zhou, Yan

2017-03-01

An investigation was conducted for 20 different types of sludge in order to identify the key organic compounds in extracellular polymeric substances (EPS) that are important in assessing variations of sludge filterability. The different types of sludge varied in initial total solids (TS) content, organic composition and pre-treatment methods. For instance, some of the sludges were pre-treated by acid, ultrasonic, thermal, alkaline, or advanced oxidation technique. The Pearson's correlation results showed significant correlations between sludge filterability and zeta potential, pH, dissolved organic carbon, protein and polysaccharide in soluble EPS (SB EPS), loosely bound EPS (LB EPS) and tightly bound EPS (TB EPS). The principal component analysis (PCA) method was used to further explore correlations between variables and similarities among EPS fractions of different types of sludge. Two principal components were extracted: principal component 1 accounted for 59.24% of total EPS variations, while principal component 2 accounted for 25.46% of total EPS variations. Dissolved organic carbon, protein and polysaccharide in LB EPS showed higher eigenvector projection values than the corresponding compounds in SB EPS and TB EPS in principal component 1. Further characterization of fractionized key organic compounds in LB EPS was conducted with size-exclusion chromatography-organic carbon detection-organic nitrogen detection (LC-OCD-OND). A numerical multiple linear regression model was established to describe relationship between organic compounds in LB EPS and sludge filterability. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of C/N ratio on extracellular polymeric substances of activated sludge from an anoxic-aerobic sequencing batch reactor treating saline wastewater.

PubMed

Wang, Zichao; Gao, Mengchun; Xin, Yanjun; Ma, Dong; She, Zonglian; Wang, Zhe; Sun, Changqing; Ren, Yun

2014-01-01

The effect of C/N ratio on extracellular polymeric substances (EPS) of activated sludge was investigated in an anoxic-aerobic sequencing batch reactor (SBR) treating saline wastewater. The protein (PN) and protein/polysaccharide (PN/PS) ratio in the loosely bound EPS (LB-EPS) increased with the decrease of C/N ratio, whereas the PS in the LB-EPS decreased. The PS, PN and PN/PS ratio in the tightly bound EPS (TB-EPS) were independent of C/N ratio. Two fluorescence peaks in the LB-EPS and TB-EPS were identified at excitation/emission (Ex/Em) wavelengths of 275-280/335-340 nm and 220-225/330-340 nm by three-dimensional excitation-emission matrix (3D-EEM) fluorescence spectroscopy, respectively. These peaks in LB-EPS and TB-EPS were, respectively, associated with tryptophan protein-like substances and aromatic protein-like substances. The tryptophan protein-like fluorescence peaks in LB-EPS showed blue shift along the Ex axis and red shift along the Em axis with the decrease of C/N ratio. Fourier transform infrared spectra suggested that the variation of C/N ratio had more distinct effect on the functional groups of protein in the LB-EPS than those in the TB-EPS. The sludge volume index value decreased with the increase of LB-EPS, but there was no correlation between SVI and TB-EPS.

The Evaluation of Foam Performance and Flooding Efficiency

NASA Astrophysics Data System (ADS)

Keliang, Wang; Yuhao, Chen; Gang, Wang; Gen, Li

2017-12-01

ROSS-Miles and spinning drop interfacial tensionmeter are used to select suitable foam system through foam composite index (FCI) and interfacial tension (IT). The selected foam system are taken to conduct further test. The further tests are evaluating the foam system resistance to adsorption with multi-round core flooding dynamic adsorption test and evaluating the performance of foam system with four kinds of different transport distance, quantitatively analyzing the foam system effective distance after dynamic adsorption. The result shows that the foaming ability and the mobilizing ability of the foam system decrease with the increase of the round of dynamic adsorption. As the transport distance increases, the foaming ability and the mobilizing ability of the foam system decrease. This result further reveals the flooding characteristics of nitrogen foam flooding, which provides a reference for the implementation of nitrogen foam flooding technology.

PrEP implementation in the Asia-Pacific region: opportunities, implementation and barriers

PubMed Central

Zablotska, Iryna; Grulich, Andrew E; Phanuphak, Nittaya; Anand, Tarandeep; Janyam, Surang; Poonkasetwattana, Midnight; Baggaley, Rachel; van Griensven, Frits; Lo, Ying-Ru

2016-01-01

Introduction HIV epidemics in the Asia-Pacific region are concentrated among men who have sex with men (MSM) and other key populations. Pre-exposure prophylaxis (PrEP) is an effective HIV prevention intervention and could be a potential game changer in the region. We discuss the progress towards PrEP implementation in the Asia-Pacific region, including opportunities and barriers. Discussion Awareness about PrEP in the Asia-Pacific is still low and so are its levels of use. A high proportion of MSM who are aware of PrEP are willing to use it. Key PrEP implementation barriers include poor knowledge about PrEP, limited access to PrEP, weak or non-existent HIV prevention programmes for MSM and other key populations, high cost of PrEP, stigma and discrimination against key populations and restrictive laws in some countries. Only several clinical trials, demonstration projects and a few larger-scale implementation studies have been implemented so far in Thailand and Australia. However, novel approaches to PrEP implementation have emerged: researcher-, facility- and community-led models of care, with PrEP services for fee and for free. The WHO consolidated guidelines on HIV testing, treatment and prevention call for an expanded access to PrEP worldwide and have provided guidance on PrEP implementation in the region. Some countries like Australia have released national PrEP guidelines. There are growing community leadership and consultation processes to initiate PrEP implementation in Asia and the Pacific. Conclusions Countries of the Asia-Pacific region will benefit from adding PrEP to their HIV prevention packages, but for many this is a critical step that requires resourcing. Having an impact on the HIV epidemic requires investment. The next years should see the region transitioning from limited PrEP implementation projects to growing access to PrEP and expansion of HIV prevention programmes. PMID:27760688

Enhancing HIV Pre-exposure, Prophylaxis Practices via an Educational Intervention.

PubMed

Newman, Rebecca; Katchi, Tasleem; Karass, Michael; Gennarelli, Melissa; Goutis, Jason; Kifayat, Alina; Solanki, Shantanu; Yandrapalli, Srikanth; Forman, Leanne; Nabors, Christopher

2018-04-20

Pre-exposure prophylaxis (PrEP) for HIV involves using antiretroviral drugs to prevent individuals at high risk from acquiring HIV infection. Most practicing primary care providers believe PrEP to be safe and effective, but less than half have prescribed or referred for PrEP. Attitudes and prescribing patterns among house officers have not been well described previously. Can an educational intervention enhance HIV PrEP practices among internal medicine house officers? This study relied on a pretest/posttest design. All categorical trainees at a medium-sized internal medicine program were offered a baseline survey to assess their knowledge on PrEP. This was followed by a PrEP-focused educational intervention and a postintervention survey. Likert scales captured perceptions regarding safety, effectiveness, barriers, factors that would promote PrEP use, potential side effects, impact on risk-taking behavior, and provider comfort level in assessing behavioral risks and in PrEP prescribing. Data were analyzed using descriptive statistics, Wilcoxon signed rank test, and the Kruskal-Wallis test. Significance was accepted for P < 0.05. Forty-eight (100%) trainees participated in the educational session, 45 (94%) in a preintervention survey, and 36 (75%) in a postintervention survey. Before PrEP training, 22% of respondents were unaware of PrEP, 78% believed PrEP was effective, 66% believed PrEP was safe, 62% had fair or poor awareness of side effects; 18% of residents had referred for or prescribed PrEP, and 31% believed they were likely to prescribe PrEP in the next 6 months. After the intervention, 94% of trainees believed PrEP was effective (P < 0.001), 92% believed PrEP was safe (P < 0.001), and two-thirds believed they were likely to prescribe PrEP in the next 6 months. Brief, focused training on HIV prevention promotes awareness, acceptance, and likelihood of prescribing PrEP by internal medicine trainees.

PrEP implementation in the Asia-Pacific region: opportunities, implementation and barriers.

PubMed

Zablotska, Iryna; Grulich, Andrew E; Phanuphak, Nittaya; Anand, Tarandeep; Janyam, Surang; Poonkasetwattana, Midnight; Baggaley, Rachel; van Griensven, Frits; Lo, Ying-Ru

2016-01-01

HIV epidemics in the Asia-Pacific region are concentrated among men who have sex with men (MSM) and other key populations. Pre-exposure prophylaxis (PrEP) is an effective HIV prevention intervention and could be a potential game changer in the region. We discuss the progress towards PrEP implementation in the Asia-Pacific region, including opportunities and barriers. Awareness about PrEP in the Asia-Pacific is still low and so are its levels of use. A high proportion of MSM who are aware of PrEP are willing to use it. Key PrEP implementation barriers include poor knowledge about PrEP, limited access to PrEP, weak or non-existent HIV prevention programmes for MSM and other key populations, high cost of PrEP, stigma and discrimination against key populations and restrictive laws in some countries. Only several clinical trials, demonstration projects and a few larger-scale implementation studies have been implemented so far in Thailand and Australia. However, novel approaches to PrEP implementation have emerged: researcher-, facility- and community-led models of care, with PrEP services for fee and for free. The WHO consolidated guidelines on HIV testing, treatment and prevention call for an expanded access to PrEP worldwide and have provided guidance on PrEP implementation in the region. Some countries like Australia have released national PrEP guidelines. There are growing community leadership and consultation processes to initiate PrEP implementation in Asia and the Pacific. Countries of the Asia-Pacific region will benefit from adding PrEP to their HIV prevention packages, but for many this is a critical step that requires resourcing. Having an impact on the HIV epidemic requires investment. The next years should see the region transitioning from limited PrEP implementation projects to growing access to PrEP and expansion of HIV prevention programmes.

Distinguishing hypothetical willingness from behavioral intentions to initiate HIV pre-exposure prophylaxis (PrEP): Findings from a large cohort of gay and bisexual men in the U.S.

PubMed

Rendina, H Jonathon; Whitfield, Thomas H F; Grov, Christian; Starks, Tyrel J; Parsons, Jeffrey T

2017-01-01

Much of the data on the acceptability of HIV Pre-Exposure Prophylaxis (PrEP) is based on willingness to take PrEP (i.e., hypothetical receptivity) rather than actual intentions (i.e., planned behavioral action) to do so. We sought to examine differences between hypothetical willingness and behavioral intentions to begin PrEP in a national sample of gay and bisexual men (GBM) across the U.S. We utilized data collected in 2015 to examine differences between those Unwilling (42.6% n = 375), Willing but not intending (41.4%, n = 365), and willing and Intending to take PrEP (15.9%, n = 140) in a multivariable, multinomial logistic regression. Men with less education had higher odds of Intending to take PrEP. Compared to men unsure about PrEP's efficacy, those who believed PrEP was at least 90% efficacious had higher odds of Intending to take PrEP. Those who saw themselves as appropriate candidates for PrEP had higher odds of Intending to take PrEP while those who saw themselves as inappropriate candidates for PrEP had lower odds of Intending to take PrEP in comparison to men unsure if they were appropriate candidates. Increased motivation for condom non-use because of perceived sexual pressure by partners was associated with higher odds of Intending to take PrEP. The groups did not differ by risk behavior nor recent STI diagnosis. Overall, the distinction between willingness and intentions to take PrEP was meaningful and may help explain disparities between PrEP acceptability and uptake. While much of the literature has focused on hypothetical willingness to take PrEP, these results highlight the importance of simultaneously assessing willingness and intentions when examining correspondence with uptake and developing interventions to increase PrEP uptake. Copyright © 2016 Elsevier Ltd. All rights reserved.

Space Station Freedom electric power system availability study

NASA Technical Reports Server (NTRS)

Turnquist, Scott R.

1990-01-01

The results are detailed of follow-on availability analyses performed on the Space Station Freedom electric power system (EPS). The scope includes analyses of several EPS design variations, these are: the 4-photovoltaic (PV) module baseline EPS design, a 6-PV module EPS design, and a 3-solar dynamic module EPS design which included a 10 kW PV module. The analyses performed included: determining the discrete power levels that the EPS will operate at upon various component failures and the availability of each of these operating states; ranking EPS components by the relative contribution each component type gives to the power availability of the EPS; determining the availability impacts of including structural and long-life EPS components in the availability models used in the analyses; determining optimum sparing strategies, for storing space EPS components on-orbit, to maintain high average-power-capability with low lift-mass requirements; and analyses to determine the sensitivity of EPS-availability to uncertainties in the component reliability and maintainability data used.

Incorporation of bacterial extracellular polysaccharide by black fly larvae (Simuliidae)

USGS Publications Warehouse

Couch, C.A.; Meyer, J.L.; Hall, R.O.

1996-01-01

Black fly larvae (Simulium) assimilated, with high efficiency (80-90%), bacterial extracellular polysaccharide (EPS) extracted from laboratory cultures of a pseudomonad isolated from the Ogeechee River. Incorporation was traced using 13C-labelled EPS offered to larvae as a coating on a mixture of 1-??m latex beads and kaolin particles. These EPS-coated particles were used to simulate natural particles, both living and dead. Solubility, protein, and nitrogen content of the EPS suggested it was a slime rather than a capsular polysaccharide. Glycosyl composition of the EPS was glucose and galactose in ?? and ?? linkages, with pyruvate, succinate, and possibly malonate constituent groups. To evaluate the incorporation of C derived from protein associated with the EPS matrix, feeding experiments were conducted using EPS with and without proteins extracted. Black fly larvae incorporated 7.2 ??g EPS C larva-1 d-1 from EPS that did not have proteins extracted, and 19.5 ??g EPS C larva-1 d-1 from EPS with proteins extracted. Carbon in protein that is typically associated with EPS was not solely or selectively incorporated. EPS incorporation rates are similar to rates of cellular bacterial carbon incorporation previously estimated for Ogeechee River black fly larvae. If EPS is generally available as a food resource, the importance of bacteria in detrital food webs may be underestimated by studies that examine only the consumption of bacterial cells.

Contribution of extracellular polymeric substances from Shewanella sp. HRCR-1 biofilms to U(VI) immobilization.

PubMed

Cao, Bin; Ahmed, Bulbul; Kennedy, David W; Wang, Zheming; Shi, Liang; Marshall, Matthew J; Fredrickson, Jim K; Isern, Nancy G; Majors, Paul D; Beyenal, Haluk

2011-07-01

The goal of this study was to quantify the contribution of extracellular polymeric substances (EPS) to U(VI) immobilization by Shewanella sp. HRCR-1. Through comparison of U(VI) immobilization using cells with bound EPS (bEPS) and cells with minimal EPS, we show that (i) bEPS from Shewanella sp. HRCR-1 biofilms contribute significantly to U(VI) immobilization, especially at low initial U(VI) concentrations, through both sorption and reduction; (ii) bEPS can be considered a functional extension of the cells for U(VI) immobilization and they likely play more important roles at lower initial U(VI) concentrations; and (iii) the U(VI) reduction efficiency is dependent upon the initial U(VI) concentration and decreases at lower concentrations. To quantify the relative contributions of sorption and reduction to U(VI) immobilization by EPS fractions, we isolated loosely associated EPS (laEPS) and bEPS from Shewanella sp. HRCR-1 biofilms grown in a hollow fiber membrane biofilm reactor and tested their reactivity with U(VI). We found that, when reduced, the isolated cell-free EPS fractions could reduce U(VI). Polysaccharides in the EPS likely contributed to U(VI) sorption and dominated the reactivity of laEPS, while redox active components (e.g., outer membrane c-type cytochromes), especially in bEPS, possibly facilitated U(VI) reduction.

Contribution of Extracellular Polymeric Substances from Shewanella sp. HRCR-1 Biofilms to U(VI) Immobilization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cao, Bin; Ahmed, B.; Kennedy, David W.

2011-06-05

The goal of this study was to quantify the contribution of extracellular polymeric substances (EPS) in U(VI) immobilization by Shewanella sp. HRCR-1. Through comparison of U(VI) immobilization using cells with bound EPS (bEPS) and cells without EPS, we showed that i) bEPS from Shewanella sp. HRCR-1 biofilms contributed significantly to U(VI) immobilization, especially at low initial U(VI) concentrations, through both sorption and reduction; ii) bEPS could be considered as a functional extension of the cells for U(VI) immobilization and they likely play more important roles at initial U(VI) concentrations; and iii) U(VI) reduction efficiency was found to be dependent uponmore » initial U(VI) concentration and the efficiency decreased at lower concentrations. To quantify relative contribution of sorption and reduction in U(VI) immobilization by EPS fractions, we isolated loosely associated EPS (laEPS) and bEPS from Shewanella sp. HRCR-1 biofilms grown in a hollow fiber membrane biofilm reactor and tested their reactivity with U(V). We found that, when in reduced form, the isolated cell-free EPS fractions could reduce U(VI). Polysaccharides in the EPS likely contributed to U(VI) sorption and dominated reactivity of laEPS while redox active components (e.g., outer membrane c-type cytochromes), especially in bEPS, might facilitate U(VI) reduction.« less

Highly cytocompatible and flexible three-dimensional graphene/polydimethylsiloxane composite for culture and electrochemical detection of L929 fibroblast cells.

PubMed

Waiwijit, Uraiwan; Maturos, Thitima; Pakapongpan, Saithip; Phokharatkul, Ditsayut; Wisitsoraat, Anurat; Tuantranont, Adisorn

2016-08-01

Recently, three-dimensional graphene interconnected network has attracted great interest as a scaffold structure for tissue engineering due to its high biocompatibility, high electrical conductivity, high specific surface area and high porosity. However, free-standing three-dimensional graphene exhibits poor flexibility and stability due to ease of disintegration during processing. In this work, three-dimensional graphene is composited with polydimethylsiloxane to improve the structural flexibility and stability by a new simple two-step process comprising dip coating of polydimethylsiloxane on chemical vapor deposited graphene/Ni foam and wet etching of nickel foam. Structural characterizations confirmed an interconnected three-dimensional multi-layer graphene structure with thin polydimethylsiloxane scaffold. The composite was employed as a substrate for culture of L929 fibroblast cells and its cytocompatibility was evaluated by cell viability (Alamar blue assay), reactive oxygen species production and vinculin immunofluorescence imaging. The result revealed that cell viability on three-dimensional graphene/polydimethylsiloxane composite increased with increasing culture time and was slightly different from a polystyrene substrate (control). Moreover, cells cultured on three-dimensional graphene/polydimethylsiloxane composite generated less ROS than the control at culture times of 3-6 h. The results of immunofluorescence staining demonstrated that fibroblast cells expressed adhesion protein (vinculin) and adhered well on three-dimensional graphene/polydimethylsiloxane surface. Good cell adhesion could be attributed to suitable surface properties of three-dimensional graphene/polydimethylsiloxane with moderate contact angle and small negative zeta potential in culture solution. The results of electrochemical study by cyclic voltammetry showed that an oxidation current signal with no apparent peak was induced by fibroblast cells and the oxidation current at an oxidation potential of +0.9 V increased linearly with increasing cell number. Therefore, the three-dimensional graphene/polydimethylsiloxane composite exhibits high cytocompatibility and can potentially be used as a conductive substrate for cell-based electrochemical sensing. © The Author(s) 2016.

40 CFR 63.1317 - PET and polystyrene affected sources-monitoring provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 12 2013-07-01 2013-07-01 false PET and polystyrene affected sources-monitoring provisions. 63.1317 Section 63.1317 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... and Resins § 63.1317 PET and polystyrene affected sources—monitoring provisions. Continuous process...

40 CFR 63.1317 - PET and polystyrene affected sources-monitoring provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 12 2014-07-01 2014-07-01 false PET and polystyrene affected sources-monitoring provisions. 63.1317 Section 63.1317 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... and Resins § 63.1317 PET and polystyrene affected sources—monitoring provisions. Continuous process...

40 CFR 63.1319 - PET and polystyrene affected sources-recordkeeping provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 12 2013-07-01 2013-07-01 false PET and polystyrene affected sources... and Resins § 63.1319 PET and polystyrene affected sources—recordkeeping provisions. (a) Except as....113. (b) Records demonstrating compliance with the applicability determination procedure for PET...

Organic pollutant loading and biodegradability of firefighting foam

NASA Astrophysics Data System (ADS)

Zhang, Xian-Zhong; Bao, Zhi-ming; Hu, Cheng; Li-Shuai, Jing; Chen, Yang

2017-11-01

Firefighting foam has been widely used as the high-performance extinguishing agent in extinguishing the liquid poor fire. It was concerned for its environmental impacts due to its massive usage. In this study, the organic loading level and the biodegradability of 18 firefighting foams commonly used in China were evaluated and compared. The COD and TOC of firefighting foam concentrates are extremely high. Furthermore, those of foam solutions are also much higher than regular wastewater. The COD/TOC ratio of synthetic foams are higher than protein foams. The 28-day biodegradation rates of 18 firefighting foams are all over 60%, indicating that they are all ready biodegradable. Protein foams (P, FP and FFFP) have the higher organic loading and lower 28-day biodegradation rates compared to the synthetic foams (Class A foam, AFFF and S). The short and long-term impact of protein foams on the environment are larger than synthetic foams.

Pre-Exposure Prophylaxis (PrEP) Use and Condomless Anal Sex: Evidence of Risk Compensation in a Cohort of Young Men Who Have Sex with Men.

PubMed

Newcomb, Michael E; Moran, Kevin; Feinstein, Brian A; Forscher, Emily; Mustanski, Brian

2018-04-01

Young men who have sex with men (YMSM) are disproportionately impacted by HIV. Pre-exposure prophylaxis (PrEP) is highly effective at preventing HIV acquisition. It remains unclear if PrEP use increases rates of condomless sex (ie, risk compensation), which may increase risk of infection if PrEP adherence is not optimal. This study aimed to examine whether PrEP use and PrEP adherence were associated with change in sexual risk behaviors in a large longitudinal cohort of YMSM reporting on multiple sexual partnerships over time. Data were obtained from the first 3 visits of an ongoing cohort study of YMSM in Chicago (analytic N = 953; 14.1% HIV-positive at baseline). Participants reported up to 4 sexual partnerships at each visit, including sexual behavior, PrEP use, and PrEP adherence within partnerships. YMSM reported higher rates of receptive condomless anal sex (CAS) in partnerships during which they were on PrEP compared with those when they were not on PrEP. This association was consistent across both HIV-negative and HIV-positive participants reporting on partnerships with both perceived HIV-negative/unknown and HIV-positive partners. The rate of receptive CAS was higher in PrEP nonadherent partnerships compared with non-PrEP partnerships. The rate of receptive CAS was also higher in PrEP nonadherent than adherent partnerships, but this was not statistically significant. These analyses provide compelling data suggesting that YMSM are engaging in risk compensation when on PrEP. If rates of receptive CAS are highest among YMSM who are PrEP nonadherent, PrEP as a prevention strategy could fail to curb HIV incidence among YMSM.

Abnormal placental development and early embryonic lethality in EpCAM-null mice.

PubMed

Nagao, Keisuke; Zhu, Jianjian; Heneghan, Mallorie B; Hanson, Jeffrey C; Morasso, Maria I; Tessarollo, Lino; Mackem, Susan; Udey, Mark C

2009-12-31

EpCAM (CD326) is encoded by the tacstd1 gene and expressed by a variety of normal and malignant epithelial cells and some leukocytes. Results of previous in vitro experiments suggested that EpCAM is an intercellular adhesion molecule. EpCAM has been extensively studied as a potential tumor marker and immunotherapy target, and more recent studies suggest that EpCAM expression may be characteristic of cancer stem cells. To gain insights into EpCAM function in vivo, we generated EpCAM -/- mice utilizing an embryonic stem cell line with a tacstd1 allele that had been disrupted. Gene trapping resulted in a protein comprised of the N-terminus of EpCAM encoded by 2 exons of the tacstd1 gene fused in frame to betageo. EpCAM +/- mice were viable and fertile and exhibited no obvious abnormalities. Examination of EpCAM +/- embryos revealed that betageo was expressed in several epithelial structures including developing ears (otocysts), eyes, branchial arches, gut, apical ectodermal ridges, lungs, pancreas, hair follicles and others. All EpCAM -/- mice died in utero by E12.5, and were small, developmentally delayed, and displayed prominent placental abnormalities. In developing placentas, EpCAM was expressed throughout the labyrinthine layer and by spongiotrophoblasts as well. Placentas of EpCAM -/- embryos were compact, with thin labyrinthine layers lacking prominent vascularity. Parietal trophoblast giant cells were also dramatically reduced in EpCAM -/- placentas. EpCAM was required for differentiation or survival of parietal trophoblast giant cells, normal development of the placental labyrinth and establishment of a competent maternal-fetal circulation. The findings in EpCAM-reporter mice suggest involvement of this molecule in development of vital organs including the gut, kidneys, pancreas, lungs, eyes, and limbs.

The anti-inflammatory effects of PGE2 on human lung macrophages are mediated by the EP4 receptor.

PubMed

Gill, Sharonjit K; Yao, Yiwen; Kay, Linda J; Bewley, Martin A; Marriott, Helen M; Peachell, Peter T

2016-11-01

PGE 2 inhibits cytokine generation from human lung macrophages. However, the EP receptor that mediates this beneficial anti-inflammatory effect of PGE 2 has not been defined. The aim of this study was to identify the EP receptor by which PGE 2 inhibits cytokine generation from human lung macrophages. This was determined by using recently developed EP receptor ligands. The effects of PGE 2 and EP-selective agonists on LPS-induced generation of TNF-α and IL-6 from macrophages were evaluated. The effects of EP 2 -selective (PF-04852946, PF-04418948) and EP 4 -selective (L-161,982, CJ-042794) receptor antagonists on PGE 2 responses were studied. The expression of EP receptor subtypes by human lung macrophages was determined by RT-PCR. PGE 2 inhibited LPS-induced and Streptococcus pneumoniae-induced cytokine generation from human lung macrophages. Analysis of mRNA levels indicated that macrophages expressed EP 2 and EP 4 receptors. L-902,688 (EP 4 receptor-selective agonist) was considerably more potent than butaprost (EP 2 receptor-selective agonist) as an inhibitor of TNF-α generation from macrophages. EP 2 receptor-selective antagonists had marginal effects on the PGE 2 inhibition of TNF-α generation, whereas EP 4 receptor-selective antagonists caused rightward shifts in the PGE 2 concentration-response curves. These studies demonstrate that the EP 4 receptor is the principal receptor that mediates the anti-inflammatory effects of PGE 2 on human lung macrophages. This suggests that EP 4 receptor agonists could be effective anti-inflammatory agents in human lung disease. © 2016 The British Pharmacological Society.

Pre-Exposure Prophylaxis: A Narrative Review of Provider Behavior and Interventions to Increase PrEP Implementation in Primary Care.

PubMed

Silapaswan, Andrew; Krakower, Douglas; Mayer, Kenneth H

2017-02-01

Since FDA approval of HIV pre-exposure prophylaxis (PrEP) for HIV prevention, attention has been focused on PrEP implementation. The CDC estimates that 1.2 million U.S. adults might benefit from PrEP, but only a minority are using PrEP, so there is a significant unmet need to increase access for those at risk for HIV. Given the large numbers of individuals who have indications for PrEP, there are not enough practicing specialists to meet the growing need for providers trained in providing PrEP. Moreover, since PrEP is a preventive intervention for otherwise healthy individuals, primary care providers (PCPs) should be primary prescribers of PrEP. There are important clinical considerations that providers should take into account when planning to prescribe PrEP, which are highlighted in the clinical case discussed. A growing body of research also suggests that some providers may be cautious about prescribing PrEP because of concerns regarding its "real-world" effectiveness, anticipated unintended consequences associated with its use, and ambiguity as to who should prescribe it. This review summarizes findings from studies that have assessed prescriber behavior regarding provision of PrEP, and offers recommendations on how to optimize PrEP implementation in primary care settings. Development and dissemination of educational interventions for PCPs and potential PrEP users are needed, including improved methods to assist clinicians in identifying appropriate PrEP candidates, and programs to promote medication adherence and access to social and behavioral health services. PCPs are well-positioned to prescribe PrEP and coordinate health-related services to improve the sexual health of their patients, but tailored educational programs are needed.

Characterization of the EP receptor types that mediate longitudinal smooth muscle contraction of human colon, mouse colon and mouse ileum.

PubMed

Fairbrother, S E; Smith, J E; Borman, R A; Cox, H M

2011-08-01

Prostaglandin E(2) (PGE(2) ) is an inflammatory mediator implicated in several gastrointestinal pathologies that affect normal intestinal transit. The aim was to establish the contribution of the four EP receptor types (EP(1-4) ), in human colon, that mediate PGE(2) -induced longitudinal smooth muscle contraction. Changes in isometric muscle tension of human colon, mouse colon and mouse ileum were measured in organ baths in response to receptor-specific agonists and antagonists. In addition, lidocaine was used to block neurogenic activity to investigate whether EP receptors were pre- or post-junctional. PGE(2) contracted longitudinal muscle from human and mouse colon and mouse ileum. These contractions were inhibited by the EP(1) receptor antagonist, EP(1) A in human colon, whereas a combination of EP(1) A and the EP(3) antagonist, L798106 inhibited agonist responses in both mouse preparations. The EP(3) agonist, sulprostone also increased muscle tension in both mouse tissues, and these responses were inhibited by lidocaine in the colon but not in the ileum. Although PGE(2) consistently contracted all three muscle preparations, butaprost decreased tension by activating smooth muscle EP(2) receptors in both colonic tissues. Alternatively, in mouse ileum, butaprost responses were lidocaine-sensitive, suggesting that it was activating prejunctional EP(2) receptors on inhibitory motor neurons. Conversely, EP(4) receptors were not functional in all the intestinal muscle preparations tested. PGE(2) -induced contraction of longitudinal smooth muscle is mediated by EP(1) receptors in human colon and by a combination of EP(1) and EP(3) receptors in mouse intestine, whereas EP(2) receptors modulate relaxation in all three preparations. © 2011 Blackwell Publishing Ltd.

Engaging healthcare providers to implement HIV pre-exposure prophylaxis.

PubMed

Krakower, Douglas; Mayer, Kenneth H

2012-11-01

Recent randomized controlled trials have demonstrated that HIV pre-exposure prophylaxis (PrEP) can decrease HIV incidence among several at-risk populations, including men who have sex with men, serodiscordant couples, and heterosexual men and women. As PrEP is a biomedical intervention that requires clinical monitoring and a high level of medication adherence, maximizing the public health effectiveness of PrEP in real-world settings will require the training of a cadre of healthcare providers to prescribe PrEP. Therefore it is critical to understand provider knowledge, practices, and attitudes towards PrEP prescribing, and to develop strategies for engaging and training providers to provide PrEP. Limited numbers of studies have focused on PrEP implementation by healthcare providers. These studies suggest that some providers are knowledgeable about PrEP, but many are not, or express misgivings. Although many clinicians report willingness to provide PrEP, few have prescribed PrEP in clinical practice. Provider comfort and skills in HIV risk assessment are suboptimal, which could limit identification of individuals who are most likely to benefit from PrEP use. Further studies to understand facilitators and barriers to HIV-risk assessment and PrEP prescribing by practicing clinicians are needed. Innovative training strategies and decision-support interventions for providers could optimize PrEP implementation and therefore merit additional research.

A Novel Workflow to Enrich and Isolate Patient-Matched EpCAMhigh and EpCAMlow/negative CTCs Enables the Comparative Characterization of the PIK3CA Status in Metastatic Breast Cancer

PubMed Central

Lampignano, Rita; Yang, Liwen; Neumann, Martin H. D.; Franken, André; Fehm, Tanja; Niederacher, Dieter; Neubauer, Hans

2017-01-01

Circulating tumor cells (CTCs), potential precursors of most epithelial solid tumors, are mainly enriched by epithelial cell adhesion molecule (EpCAM)-dependent technologies. Hence, these approaches may overlook mesenchymal CTCs, considered highly malignant. Our aim was to establish a workflow to enrich and isolate patient-matched EpCAMhigh and EpCAMlow/negative CTCs within the same blood samples, and to investigate the phosphatidylinositol 3-kinase catalytic subunit alpha (PIK3CA) mutational status within single CTCs. We sequentially processed metastatic breast cancer (MBC) blood samples via CellSearch® (EpCAM-based) and via Parsortix™ (size-based) systems. After enrichment, cells captured in Parsortix™ cassettes were stained in situ for nuclei, cytokeratins, EpCAM and CD45. Afterwards, sorted cells were isolated via CellCelector™ micromanipulator and their genomes were amplified. Lastly, PIK3CA mutational status was analyzed by combining an amplicon-based approach with Sanger sequencing. In 54% of patients′ blood samples both EpCAMhigh and EpCAMlow/negative cells were identified and successfully isolated. High genomic integrity was observed in 8% of amplified genomes of EpCAMlow/negative cells vs. 28% of EpCAMhigh cells suggesting an increased apoptosis in the first CTC-subpopulation. Furthermore, PIK3CA hotspot mutations were detected in both EpCAMhigh and EpCAMlow/negative CTCs. Our workflow is suitable for single CTC analysis, permitting—for the first time—assessment of the heterogeneity of PIK3CA mutational status within patient-matched EpCAMhigh and EpCAMlow/negative CTCs. PMID:28858218

Wetting behavior on hexagonally close-packed polystyrene bead arrays with different topographies.

PubMed

Park, Yi-Seul; Yoon, Seo Young; Lee, Jin Seok

2016-01-21

Herein, we investigated the wetting behavior of hexagonally close-packed polystyrene bead arrays with different bead diameters and surface flatness. The contact angle was found to be influenced by the surface roughness as well as the contact area of the polystyrene bead array with a water droplet.

Packing Products: Polystyrene vs. Cornstarch

ERIC Educational Resources Information Center

Starr, Suzanne

2009-01-01

Packing materials such as polystyrene take thousands of years to decompose, whereas packing peanuts made from cornstarch, which some companies are now using, can serve the same purpose, but dissolve in water. The author illustrates this point to her class one rainy day using the sculptures students made from polystyrene and with the cornstarch…

40 CFR 63.1317 - PET and polystyrene affected sources-monitoring provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 12 2012-07-01 2011-07-01 true PET and polystyrene affected sources-monitoring provisions. 63.1317 Section 63.1317 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... § 63.1317 PET and polystyrene affected sources—monitoring provisions. Continuous process vents using a...

40 CFR 63.1320 - PET and polystyrene affected sources-reporting provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 12 2012-07-01 2011-07-01 true PET and polystyrene affected sources... § 63.1320 PET and polystyrene affected sources—reporting provisions. (a) Except as specified in... PET Affected Sources Using a Dimethyl Terephthalate Process. Owners or operators complying with § 63...

40 CFR 63.1319 - PET and polystyrene affected sources-recordkeeping provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 11 2011-07-01 2011-07-01 false PET and polystyrene affected sources... § 63.1319 PET and polystyrene affected sources—recordkeeping provisions. (a) Except as specified in... demonstrating compliance with the applicability determination procedure for PET affected sources using a...

40 CFR 63.1320 - PET and polystyrene affected sources-reporting provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 12 2013-07-01 2013-07-01 false PET and polystyrene affected sources... and Resins § 63.1320 PET and polystyrene affected sources—reporting provisions. (a) Except as...) Reporting for PET Affected Sources Using a Dimethyl Terephthalate Process. Owners or operators complying...

40 CFR 63.1320 - PET and polystyrene affected sources-reporting provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true PET and polystyrene affected sources... § 63.1320 PET and polystyrene affected sources—reporting provisions. (a) Except as specified in... PET Affected Sources Using a Dimethyl Terephthalate Process. Owners or operators complying with § 63...

40 CFR 63.1317 - PET and polystyrene affected sources-monitoring provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 11 2011-07-01 2011-07-01 false PET and polystyrene affected sources-monitoring provisions. 63.1317 Section 63.1317 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... § 63.1317 PET and polystyrene affected sources—monitoring provisions. Continuous process vents using a...

40 CFR 63.1320 - PET and polystyrene affected sources-reporting provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 11 2011-07-01 2011-07-01 false PET and polystyrene affected sources... § 63.1320 PET and polystyrene affected sources—reporting provisions. (a) Except as specified in... PET Affected Sources Using a Dimethyl Terephthalate Process. Owners or operators complying with § 63...

40 CFR 63.1317 - PET and polystyrene affected sources-monitoring provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true PET and polystyrene affected sources-monitoring provisions. 63.1317 Section 63.1317 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... § 63.1317 PET and polystyrene affected sources—monitoring provisions. Continuous process vents using a...

Sequential pyrolysis of plastic to recover polystyrene HCL and terephthalic acid

DOEpatents

Evans, Robert J.; Chum, Helena L.

1995-01-01

A process of pyrolyzing plastic waste feed streams containing polyvinyl chloride, polyethylene terephthalate, polystyrene and polyethylene to recover polystyrene HCl and terephthalic acid comprising: heating the plastic waste feed stream to a first temperature; adding an acid or base catalyst on an oxide or carbonate support; heating the plastic waste feed stream to pyrolyze polyethylene terephthalate and polyvinyl chloride; separating terephthalic acid or HCl; heating to a second temperature to pyrolyze polystyrene; separating styrene; heating the waste feed stream to a third temperature to pyrolyze polyethylene; and separating hydrocarbons.

Coupling of carboxylic groups onto the surface of polystyrene parts during fused filament fabrication

NASA Astrophysics Data System (ADS)

Nagel, Jürgen; Zimmermann, Philipp; Schubert, Oliver; Simon, Frank; Schlenstedt, Kornelia

2017-11-01

A method for the fabrication of polystyrene parts, modified with carboxylic groups during Fused Filament Fabrication (FFF), is being introduced. This method is based on the application of a thin layer of a reactive polymer carrying carboxylic groups on a substrate surface. A polystyrene film is printed on top of this layer. During contact between the hot melt and the reactive layer, a Friedel-Crafts type acylation using a green catalyst takes place, which attaches the reactive polymer to the polystyrene surface. The modified surface is homogeneous, hydrophilic and able to bind copper ions. The method could be used to fabricate unique parts of polystyrene with tailored surface functionalisation. It could be applied for laboratory use, e.g. for the manufacture of lab-on-a-chip devices.

Determining the unique refractive index properties of solid polystyrene aerosol using broadband Mie scattering from optically trapped beads.

PubMed

Jones, Stephanie H; King, Martin D; Ward, Andrew D

2013-12-21

A method is described to measure the refractive index dispersion with wavelength of optically trapped solid particles in air. Knowledge of the refraction properties of solid particles is critical for the study of aerosol; both in the laboratory and in the atmosphere for climate studies. Single micron-sized polystyrene beads were optically trapped in air using a vertically aligned counter-propagating configuration of focussed laser beams. Each bead was illuminated using white light from a broadband light emitting diode (LED) and elastic scattering within the bead was collected onto a spectrograph. The resulting Mie spectra were analysed to accurately determine polystyrene bead radii to ±0.4 nm and values of the refractive index to ±0.0005 over a wavelength range of 480-700 nm. We demonstrate that optical trapping combined with elastic scattering can be used to both accurately size polystyrene beads suspended in air and determine their wavelength dependent refractive index. The refractive index dispersions are in close agreement with reported values for polystyrene beads in aqueous dispersion. Our results also demonstrate a variation in the refractive index of polystyrene, from bead to bead, in a commercial sample. The measured variation highlights that care must be taken when using polystyrene beads as a calibration aerosol.

Biodegradation of polystyrene-graft-starch copolymers in three different types of soil.

PubMed

Nikolic, Vladimir; Velickovic, Sava; Popovic, Aleksandar

2014-01-01

Materials based on polystyrene and starch copolymers are used in food packaging, water pollution treatment, and textile industry, and their biodegradability is a desired characteristic. In order to examine the degradation patterns of modified, biodegradable derivates of polystyrene, which may keep its excellent technical features but be more environmentally friendly at the same time, polystyrene-graft-starch biomaterials obtained by emulsion polymerization in the presence of new type of initiator/activator pair (potassium persulfate/different amines) were subjected to 6-month biodegradation by burial method in three different types of commercially available soils: soil rich in humus and soil for cactus and orchid growing. Biodegradation was monitored by mass decrease, and the highest degradation rate was achieved in soil for cactus growing (81.30%). Statistical analysis proved that microorganisms in different soil samples have different ability of biodegradation, and there is a significant negative correlation between the share of polystyrene in copolymer and degree of biodegradation. Grafting of polystyrene on starch on one hand prevents complete degradation of starch that is present (with maximal percentage of degraded starch ranging from 55 to 93%), while on the other hand there is an upper limit of share of polystyrene in the copolymer (ranging from 37 to 77%) that is preventing biodegradation of degradable part of copolymers.

Extracellular Polymeric Substance Production and Aggregated Bacteria Colonization Influence the Competition of Microbes in Biofilms.

PubMed

Jayathilake, Pahala G; Jana, Saikat; Rushton, Steve; Swailes, David; Bridgens, Ben; Curtis, Tom; Chen, Jinju

2017-01-01

The production of extracellular polymeric substance (EPS) is important for the survival of biofilms. However, EPS production is costly for bacteria and the bacterial strains that produce EPS (EPS+) grow in the same environment as non-producers (EPS-) leading to competition between these strains for nutrients and space. The outcome of this competition is likely to be dependent on factors such as initial attachment, EPS production rate, ambient nutrient levels and quorum sensing. We use an Individual-based Model (IbM) to study the competition between EPS+ and EPS- strains by varying the nature of initial colonizers which can either be in the form of single cells or multicellular aggregates. The microbes with EPS+ characteristics obtain a competitive advantage if they initially colonize the surface as smaller aggregates and are widely spread-out between the cells of EPS-, when both are deposited on the substratum. Furthermore, the results show that quorum sensing-regulated EPS production may significantly reduce the fitness of EPS producers when they initially deposit as aggregates. The results provide insights into how the distribution of bacterial aggregates during initial colonization could be a deciding factor in the competition among different strains in biofilms.

The Dutch EPS Registry: increasing the knowledge of encapsulating peritoneal sclerosis.

PubMed

Korte, M R; Boeschoten, E W; Betjes, M G H

2009-09-01

Encapsulating peritoneal sclerosis (EPS) is a rare condition characterised by fibrotic thickening of the visceral peritoneum, leading to encapsulating of the intestines with partial or total intestinal obstruction. EPS is a serious complication of peritoneal dialysis (PD) with high morbidity and a mortality exceeding 50%. At present, there is uncertainty concerning the incidence and the risk factors involved in the development of EPS. To address these questions a nationwide registry has been initiated. The primary goals of the registry are to record the incidence of EPS and investigate the association of different variables, such as PD duration, medication, dialysis solutions and kidney transplantation with EPS. The registry will improve the knowledge of EPS and will serve to develop guidelines and necessary management strategies. From the registry different research activities can be initiated. A major challenge lies in the establishment of criteria that allow a timely diagnosis of EPS. At present, there are no diagnostic tools that can accurately detect EPS at an early stage. For this reason, besides patients with proven EPS, the clinical suspicion of EPS will be a sufficient criterion for inclusion in the registry. This nationwide EPS registry is currently enrolling patients.

Composition and functional group characterization of extracellular polymeric substances (EPS) in activated sludge: the impacts of polymerization degree of proteinaceous substrates.

PubMed

Wang, Bin-Bin; Liu, Xue-Ting; Chen, Jian-Meng; Peng, Dang-Cong; He, Feng

2018-02-01

Characteristics of extracellular polymeric substances (EPS) in activated sludge strongly depend on wastewater substrates. Proteinaceous substrates (ProS) present in heterogeneous polymeric form are intrinsic and important parts of wastewater substrates for microorganisms in activated sludge systems. However, correlations between ProS and characteristics of EPS are scarce. This study systematically explored the impacts of monomeric (Mono-), low polymeric (LoP-) and high polymeric (HiP-) ProS on compositions and functional groups of EPS in activated sludge. The results showed that the change of polymerization degree of ProS significantly altered the composition of EPS. Compared to EPS Mono-ProS , the proportion of proteins in EPS LoP-ProS and EPS HiP-ProS increased by 12.8% and 27.7%, respectively, while that of polysaccharides decreased by 22.9% and 63.6%, respectively. Moreover, the proportion of humic compounds in EPS LoP-ProS and EPS HiP-ProS were ∼6 and ∼16-fold higher than that in EPS Mono-ProS , respectively. The accumulation of humic compounds in EPS increased the unsaturation degree of EPS molecules, and thereby reduced the energy requirement for electrons transition of amide bonds and aromatic groups. Size exclusion chromatography (SEC) analyses detected more molecular clusters in EPS HiP-ProS , indicating more complex composition of EPS in HiP-ProS fed activated sludge. Spectroscopic characterization revealed the dominance of hydrocarbon, protein, polysaccharide and aromatic associated bonds in all three EPS. Nevertheless, with the increase of polymerization degree of ProS, the protein associated bonds (such as CONH, CO, NC, NH) increased, while the polysaccharide associated bonds (such as COC, COH, OCOH) decreased. This paper paves a path to understand the role of ProS in affecting the production and characteristics of EPS in biological wastewater treatment systems. Copyright © 2017 Elsevier Ltd. All rights reserved.

Extracellular polysaccharides produced by cooling water tower biofilm bacteria and their possible degradation.

PubMed

Ceyhan, Nur; Ozdemir, Guven

2008-01-01

The extracellular polymers (EPS) of biofilm bacteria that can cause heat and mass transfer problems in cooling water towers in the petrochemical industry were investigated. In addition, these microorganisms were screened for their ability to grow and degrade their own EPS and the EPS of other species. Twelve bacteria producing the most EPS were isolated from cooling water towers and characterized biochemically by classic and commercial systems. These were species of Pseudomonas, Burkholderia, Aeromonas, Pasteurella, Pantoea, Alcaligenes and Sphingomonas. EPS of these species were obtained by propan-2-ol precipitation and centrifugation from bacterial cultures in media enriched with glucose, sucrose or galactose. EPS yields were of 1.68-4.95 g l(-1). These EPS materials were characterized for total sugar and protein contents. Their total sugar content ranged from 24 to 56% (g sugar g(-1) EPS), and their total protein content ranged from 10 to 28% (g protein g(-1) EPS). The monosaccharide compositions of EPS were determined by HPLC. Generally, these compositions were enriched in galactose and glucose, with lesser amounts of mannose, rhamnose, fructose and arabinose. All bacteria were investigated in terms of EPS degradation. Eight of the bacteria were able to utilize EPS from Burkholderia cepacia, seven of the bacteria were able to utilize EPS from Pseudomonas sp. and Sphingomonas paucimobilis. The greatest viscosity reduction of B. cepacia was obtained with Pseudomonas sp. The results show that the bacteria in this study are able to degrade EPS from biofilms in cooling towers.

Optical Aptamer Probes of Fluorescent Imaging to Rapid Monitoring of Circulating Tumor Cell

PubMed Central

Hwang, Ji Yeon; Kim, Sang Tae; Han, Ho-Seong; Kim, Kyunggon; Han, Jin Soo

2016-01-01

Fluorescence detecting of exogenous EpCAM (epithelial cell adhesion molecule) or muc1 (mucin1) expression correlated to cancer metastasis using nanoparticles provides pivotal information on CTC (circulating tumor cell) occurrence in a noninvasive tool. In this study, we study a new skill to detect extracellular EpCAM/muc1 using quantum dot-based aptamer beacon (QD-EpCAM/muc1 ALB (aptamer linker beacon). The QD-EpCAM/muc1 ALB was designed using QDs (quantum dots) and probe. The EpCAM/muc1-targeting aptamer contains a Ep-CAM/muc1 binding sequence and BHQ1 (black hole quencher 1) or BHQ2 (black hole quencher2). In the absence of target EpCAM/muc1, the QD-EpCAM/muc1 ALB forms a partial duplex loop-like aptamer beacon and remained in quenched state because the BHQ1/2 quenches the fluorescence signal-on of the QD-EpCAM/muc1 ALB. The binding of EpCAM/muc1 of CTC to the EpCAM/muc1 binding aptamer sequence of the EpCAM/muc1-targeting oligonucleotide triggered the dissociation of the BHQ1/2 quencher and subsequent signal-on of a green/red fluorescence signal. Furthermore, acute inflammation was stimulated by trigger such as caerulein in vivo, which resulted in increased fluorescent signal of the cy5.5-EpCAM/muc1 ALB during cancer metastasis due to exogenous expression of EpCAM/muc1 in Panc02-implanted mouse model. PMID:27886058

Extracellular polymeric substances facilitate the biosorption of phenanthrene on cyanobacteria Microcystis aeruginosa.

PubMed

Bai, Leilei; Xu, Huacheng; Wang, Changhui; Deng, Jiancai; Jiang, Helong

2016-11-01

Phytoplankton-derived extracellular polymeric substances (EPS) are of vital importance for the biogeochemical cycles of hydrophobic organic pollutants in lake ecosystems. In this study, roles of loosely-bound EPS (LB-EPS) and tightly bound EPS (TB-EPS) in biosorption of phenanthrene (PHE) on a typical cyanobacteria Microcystis aeruginosa were investigated. The results showed that the biosorption of PHE on M. aeruginosa cell varied lasted 24 h, while the binding of PHE to LB-EPS and TB-EPS reached equilibrium within less than 2 h. The equilibrium biosorption capacities of M. aeruginosa cell, LB-EPS and TB-EPS were 6.78, 12.31, and 9.47 μg mg(-1), respectively, indicating that the binding of PHE to EPS was a considerable process involved in biosorption. Fluorescence quenching titration revealed that increasing temperature induced more binding sites in EPS for PHE and the binding process was driven by electrostatic force and hydrophobic interactions. Interestingly, dynamic and static quenching processes occurred simultaneously for the binding of PHE to protein-like substances in EPS, whereas the binding of PHE to humic-like substances belonged to static quenching. The relatively higher contents of proteins in LB-EPS produced a stronger binding capacity of PHE. Overall, the interactions between hydrophobic organic pollutants and cyanobacterial EPS are favorable to the bioaccumulation of hydrophobic organic pollutants in cyanobacteria and facilitate the regulatory function of cyanobacterial biomass as a biological pump. Copyright © 2016 Elsevier Ltd. All rights reserved.

Network Meta-Analysis Comparing the Efficacy of Therapeutic Treatments for Bronchiolitis in Children.

PubMed

Guo, Caili; Sun, Xiaomin; Wang, Xiaowen; Guo, Qing; Chen, Dan

2018-01-01

This study aims to compare placebo (PBO) and 7 therapeutic regimens-namely, bronchodilator agents (BAs), hypertonic saline (HS), BA ± HS, corticosteroids (CS), epinephrine (EP), EP ± CS, and EP ± HS-to determine the optimal bronchiolitis treatment. We plotted networks using the curative outcome of several studies and specified the relations among the experiments by using mean difference, standardized mean difference, and corresponding 95% credible interval. The surface under the cumulative ranking curve (SUCRA) was used to separately rank each therapy on clinical severity score (CSS) and length of hospital stay (LHS). This network meta-analysis included 40 articles from 1995 to 2016 concerning the treatment of bronchiolitis in children. All 7 therapeutic regimens displayed no significant difference to PBO with regard to CSS in our study. Among the 7 therapies, BA performed better than CS. As for LHS, EP and EP ± HS had an advantage over PBO. Moreover, EP and EP ± HS were also more efficient than BA. The SUCRA results showed that EP ± CS is most effective, and EP ± HS is second most effective with regard to CSS. With regard to LHS, EP ± HS ranked first, EP ± CS ranked second, and EP ranked third. We recommend EP ± CS and EP ± HS as the first choice for bronchiolitis treatment in children because of their outstanding performance with regard to CSS and LHS. © 2017 American Society for Parenteral and Enteral Nutrition.

A review of aqueous foam in microscale.

PubMed

Anazadehsayed, Abdolhamid; Rezaee, Nastaran; Naser, Jamal; Nguyen, Anh V

2018-06-01

In recent years, significant progress has been achieved in the study of aqueous foams. Having said this, a better understanding of foam physics requires a deeper and profound study of foam elements. This paper reviews the studies in the microscale of aqueous foams. The elements of aqueous foams are interior Plateau borders, exterior Plateau borders, nodes, and films. Furthermore, these elements' contribution to the drainage of foam and hydraulic resistance are studied. The Marangoni phenomena that can happen in aqueous foams are listed as Marangoni recirculation in the transition region, Marangoni-driven flow from Plateau border towards the film in the foam fractionation process, and Marangoni flow caused by exposure of foam containing photosurfactants under UV. Then, the flow analysis of combined elements of foam such as PB-film along with Marangoni flow and PB-node are studied. Next, we contrast the behavior of foams in different conditions. These various conditions can be perturbation in the foam structure caused by injected water droplets or waves or using a non-Newtonian fluid to make the foam. Further review is about the effect of oil droplets and particles on the characteristics of foam such as drainage, stability and interfacial mobility. Copyright © 2018 Elsevier B.V. All rights reserved.

Innovative test method for the estimation of the foaming tendency of substrates for biogas plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moeller, Lucie, E-mail: lucie.moeller@ufz.de; Eismann, Frank, E-mail: info@antoc.de; Wißmann, Daniel, E-mail: d.s.wissmann@gmx.de

2015-07-15

Graphical abstract: Display Omitted - Highlights: • Foaming in biogas plants depends on the interactions between substrate and digestate. • Foaming tests enable the evaluation of substrate foaming tendency in biogas plants. • Leipzig foam tester enables foaming tests of substrates prior to use. - Abstract: Excessive foaming in anaerobic digestion occurs at many biogas plants and can cause problems including plugged gas pipes. Unfortunately, the majority of biogas plant operators are unable to identify the causes of foaming in their biogas reactor. The occurrence of foaming is often related to the chemical composition of substrates fed to the reactor.more » The consistency of the digestate itself is also a crucial part of the foam formation process. Thus, no specific recommendations concerning substrates can be given in order to prevent foam formation in biogas plants. The safest way to avoid foaming is to test the foaming tendency of substrates on-site. A possible solution is offered by an innovative foaming test. With the help of this tool, biogas plant operators can evaluate the foaming disposition of new substrates prior to use in order to adjust the composition of substrate mixes.« less

Development of Defoamers for Confinenment Foam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffman, D M; Mitchell, A R

Aqueous foam concentrate (AFC) 380 foam was developed by Sandia National Laboratory as a blast mitigation foam for unexploded ordnance (UXO) and its ''engineered foam structure'' is reported to be able to ''envelop chemical or biological aerosols'' [1]. It is similar to commercial fire-fighting foams, consisting mostly of water with small amounts of two alcohols, an ether and surfactant. It also contains xanthan gum, probably, to strengthen the foam film and delay drainage. The concentrate is normally diluted in a 6:94 ratio with water for foaming applications. The diluted solution is normally foamed with air to an expansion factor ofmore » about 100 (density 0.01 g/cc), which is called ''dry'' foam. Higher density foam (0.18 > {rho} > 0.03 g/cc) was discovered which had quite different characteristics from ''dry'' foam and was called ''wet'' foam. Some characterization of these foams has also been carried out, but the major effort described in this document is the evaluation, at the small and medium scale, of chemical, mechanical and thermal approaches to defoaming AFC 380 foam. Several chemical approaches to defoaming were evaluated including oxidation and precipitation of the xanthan, use of commercial oil-emulsion or suspension defoamers, pH modification, and cation exchange with the surfactant. Of these the commercial defoamers were most effective. Two mechanical approaches to defoaming were evaluated: pressure and foam rupture with very fine particles. Pressure and vacuum techniques were considered too difficult for field applications but high surface area silica particles worked very well on dry foam. Finally simple thermal techniques were evaluated. An order-disorder transition occurs in xanthan solutions at about 60 C, which may be responsible for the effectiveness of hot air as a defoamer. During defoaming of 55 gallons of foam with hot air, after about 70% of the AFC 380 foam had been defoamed, the effectiveness of hot air was dramatically reduced. Approximately 15 gal of residual foam containing mostly small bubbles was resistant to further defoaming by methods that had been effective on the original, dry foam. In this paper the residual foam is referred to as ''wet'' and the original foam is referred to as ''dry''. Methods for generating ''wet'' foam in small to moderate quantities for defoaming experiments have been developed. Methods for defoaming wet foam are currently under study.« less

E-type prostanoid receptor 4 (EP4) in disease and therapy

PubMed Central

Konya, Viktoria; Marsche, Gunther; Schuligoi, Rufina; Heinemann, Akos

2013-01-01

The large variety of biological functions governed by prostaglandin (PG) E2 is mediated by signaling through four distinct E-type prostanoid (EP) receptors. The availability of mouse strains with genetic ablation of each EP receptor subtype and the development of selective EP agonists and antagonists have tremendously advanced our understanding of PGE2 as a physiologically and clinically relevant mediator. Moreover, studies using disease models revealed numerous conditions in which distinct EP receptors might be exploited therapeutically. In this context, the EP4 receptor is currently emerging as most versatile and promising among PGE2 receptors. Anti-inflammatory, anti-thrombotic and vasoprotective effects have been proposed for the EP4 receptor, along with its recently described unfavorable tumor-promoting and pro-angiogenic roles. A possible explanation for the diverse biological functions of EP4 might be the multiple signaling pathways switched on upon EP4 activation. The present review attempts to summarize the EP4 receptor-triggered signaling modules and the possible therapeutic applications of EP4-selective agonists and antagonists. PMID:23523686

40 CFR 63.8830 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Flexible Polyurethane Foam Fabrication... chemical substance that is applied for the purpose of bonding foam to foam, foam to fabric, or foam to any... means the process of bonding flexible foam to one or more layers of material by heating the foam surface...

40 CFR 63.8830 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Flexible Polyurethane Foam Fabrication... chemical substance that is applied for the purpose of bonding foam to foam, foam to fabric, or foam to any... means the process of bonding flexible foam to one or more layers of material by heating the foam surface...

40 CFR 63.8830 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Flexible Polyurethane Foam Fabrication... chemical substance that is applied for the purpose of bonding foam to foam, foam to fabric, or foam to any... means the process of bonding flexible foam to one or more layers of material by heating the foam surface...

40 CFR 63.8830 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Flexible Polyurethane Foam Fabrication... chemical substance that is applied for the purpose of bonding foam to foam, foam to fabric, or foam to any... means the process of bonding flexible foam to one or more layers of material by heating the foam surface...

40 CFR 63.8830 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Flexible Polyurethane Foam Fabrication... chemical substance that is applied for the purpose of bonding foam to foam, foam to fabric, or foam to any... means the process of bonding flexible foam to one or more layers of material by heating the foam surface...

Fabrication of low-crystalline carbonate apatite foam bone replacement based on phase transformation of calcite foam.

PubMed

Maruta, Michito; Matsuya, Shigeki; Nakamura, Seiji; Ishikawa, Kunio

2011-01-01

Carbonate apatite (CO(3)Ap) foam may be an ideal bone substitute as it is sidelined to cancellous bone with respect to its chemical composition and structure. However, CO(3)Ap foam fabricated using α-tricalcium phosphate foam showed limited mechanical strength. In the present study, feasibility of the fabrication of calcite which could be a precursor of CO(3)Ap was studied. Calcite foam was successfully fabricated by the so-called "ceramic foam" method using calcium hydroxide coated polyurethane foam under CO(2)+O(2) atmosphere. Then the calcite foam was immersed in Na(2)HPO(4) aqueous solution for phase transformation based on dissolution-precipitation reaction. When CaO-free calcite foam was immersed in Na(2)HPO(4) solution, low-crystalline CO(3)Ap foam with 93-96% porosity and fully interconnected porous structure was fabricated. The compressive strength of the foam was 25.6 ± 6 kPa. In light of these results, we concluded that the properties of the precursor foam were key factors for the fabrication of CO(3)Ap foams.

Efficient continuous dryer for flexible polyurethane foam and cleaning apparatus

DOEpatents

Jody, Bassam; Daniels, Edward; Libera, Joseph A.

1999-01-01

A method of cleaning polyurethane foams where the material is transported through a wash station while alternately soaking the polyurethane foam in an organic solvent and squeezing solvent from the polyurethane foam a number of times. Then the polyurethane foam is sent through a rinse or solvent transfer station for reducing the concentration of solvent in the foam. The rinsed polyurethane foam is sent to a drying station wherein the foam is repeatedly squeezed while being exposed to hot air to remove wet air from the foam.

Efficient continuous dryer for flexible polyurethane foam and cleaning apparatus

DOEpatents

Jody, B.; Daniels, E.; Libera, J.A.

1999-03-16

A method of cleaning polyurethane foams where the material is transported through a wash station while alternately soaking the polyurethane foam in an organic solvent and squeezing solvent from the polyurethane foam a number of times. Then the polyurethane foam is sent through a rinse or solvent transfer station for reducing the concentration of solvent in the foam. The rinsed polyurethane foam is sent to a drying station wherein the foam is repeatedly squeezed while being exposed to hot air to remove wet air from the foam. 4 figs.

Effect of salivary secretory IgA on the adhesion of Candida albicans to polystyrene.

PubMed

San Millán, R; Elguezabal, N; Regúlez, P; Moragues, M D; Quindós, G; Pontón, J

2000-09-01

Attachment of Candida albicans to plastic materials of dental prostheses or to salivary macromolecules adsorbed on their surface is believed to be a critical event in the development of denture stomatitis. In an earlier study, it was shown that adhesion of C. albicans to polystyrene, a model system to study the adhesion of C. albicans to plastic materials, can be partially inhibited with an mAb directed against cell wall polysaccharides of C. albicans. In the present study, the role of whole saliva in the adhesion of C. albicans to polystyrene has been investigated, and three mAbs directed against epitopes of cell wall mannoproteins have been used to mimic the inhibitory effect observed with salivary secretory IgA (sIgA) on the adhesion of C. albicans to polystyrene. In the absence of whole saliva, adherence of C. albicans 3153 increased with germination. However, the presence of whole saliva enhanced the adhesion to polystyrene of C. albicans 3153 yeast cells but decreased the adhesion of germinated cells. The enhancement of adhesion of yeast cells to polystyrene mediated by saliva was confirmed with an agerminative mutant of C. albicans 3153. The inhibition of the adhesion of C. albicans 3153 germ tubes to polystyrene was due to the salivary sIgA since sIgA-depleted saliva enhanced the adhesion of C. albicans 3153 to polystyrene. The inhibitory effect mediated by sIgA was not related to the inhibition of germination but to the blockage of adhesins expressed on the cell wall surface of the germ tubes. The three mAbs studied reduced the adhesion of C. albicans 3153 to polystyrene at levels equivalent to those for purified sIgA. The highest reduction in the adhesion was obtained with the IgA mAb N3B. The best results were obtained when the three mAbs were combined. The results suggest that whole saliva plays a different role in the adhesion of C. albicans to polystyrene depending on the morphological phase of C. albicans. These results may give new insights into the conflicting role of saliva in the adhesion of C. albicans to plastic materials of dental prostheses.

Erect panicle2 encodes a novel protein that regulates panicle erectness in indica rice.

PubMed

Zhu, Keming; Tang, Ding; Yan, Changjie; Chi, Zhengchang; Yu, Hengxiu; Chen, Jianmin; Liang, Jiansheng; Gu, Minghong; Cheng, Zhukuan

2010-02-01

Rice (Oryza sativa L.) inflorescence (panicle) architecture is an important agronomic trait for rice breeding. A number of high-yielding japonica rice strains, characterized by an erect panicle (EP) of their architecture, have been released as commercial varieties in China. But no EP-type indica varieties are released so far. Here, we identified two allelic erect-panicle mutants in indica rice, erect panicle2-1 (ep2-1) and erect panicle2-2 (ep2-2), exhibiting the characteristic erect panicle phenotype. Both mutants were derived from spontaneous mutation. We cloned the EP2 gene by way of a map-based cloning strategy, and a transgenic complementation test rescued the phenotype of ep2-1. Anatomical investigations revealed that the ep2 mutants have more vascular bundles and a thicker stem than that of wild-type plants, explaining the panicle erectness phenotype in ep2 mutants. It was shown that EP2 was specifically expressed in the vascular bundles of internodes by GUS staining and RT-PCR. EP2 encodes a novel plant-specific protein, which localizes to the endoplasmic reticulum with unknown biochemical function. In addition, EP2 also regulates other panicle characteristics, such as panicle length and grain size, but grain number per panicle shows little change, indicating that the mutation of the ep2 gene could be applied in EP-type indica rice breeding.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saeed, Noha M.; El-Demerdash, Ebtehal; Abdel-Rahman, Hanaa M.

Methyl palmitate (MP) and ethyl palmitate (EP) are naturally occurring fatty acid esters reported as inflammatory cell inhibitors. In the current study, the potential anti-inflammatory activity of MP and EP was evaluated in different experimental rat models. Results showed that MP and EP caused reduction of carrageenan-induced rat paw edema in addition to diminishing prostaglandin E2 (PGE2) level in the inflammatory exudates. In lipopolysaccharide (LPS)-induced endotoxemia in rats, MP and EP reduced plasma levels of tumor necrosis factor-α (TNF-α) and interleukin-6 (IL-6). MP and EP decreased NF-κB expression in liver and lung tissues and ameliorated histopathological changes caused by LPS.more » Topical application of MP and EP reduced ear edema induced by croton oil in rats. In the same animal model, MP and EP reduced neutrophil infiltration, as indicated by decreased myeloperoxidase (MPO) activity. In conclusion, this study demonstrates the effectiveness of MP and EP in combating inflammation in several experimental models. -- Highlights: ► Efficacy of MP and EP in combating inflammation was displayed in several models. ► MP and EP reduced carrageenan-induced rat paw edema and prostaglandin E2 level. ► MP and EP decreased TNF-α and IL-6 levels in experimental endotoxemia. ► MP and EP reduced NF-κB expression and histological changes in rat liver and lung. ► MP and EP reduced croton oil-induced ear edema and neutrophil infiltration.« less

Handbook for using foams to control vapors from hazardous spills. Report for April 1984-September 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Evans, M.L.; Carroll, H.A.

1986-07-01

The handbook describes basic types of foams that may be used to control vapor hazards from spilled volatile chemicals. It provides a table to be used by spill-response personnel to choose an appropriate foam based on the type of chemical spill. Six general types of foams, surfactant (syndet) foams, aqueous film forming foams (AFFF), alcohol type or polar solvent type foams (ATF), and special foams such as Hazmat NF no. 1 which was developed especially for alkaline spills. The handbook provides the basis for spill responders to evaluate and select a foam for vapor control by using the test methodsmore » presented or by considering manufacturers specifications for foam-expansion ratios and quarter drainage times. The responder is encouraged to maximize the effectiveness of a foam by trying different nozzles, distances of applications, and thicknesses of the foam layers.« less

The impact of EpCAM expression on response to chemotherapy and clinical outcomes in patients with epithelial ovarian cancer.

PubMed

Tayama, Shingo; Motohara, Takeshi; Narantuya, Dashdemberel; Li, Chenyan; Fujimoto, Koichi; Sakaguchi, Isao; Tashiro, Hironori; Saya, Hideyuki; Nagano, Osamu; Katabuchi, Hidetaka

2017-07-04

Epithelial ovarian cancer is a highly lethal malignancy; moreover, overcoming chemoresistance is the major challenging in treating ovarian cancer patients. The cancer stem cell (CSC) hypothesis considers CSCs to be the main culprits in driving tumor initiation, metastasis, and resistance to conventional therapy. Although growing evidence suggest that CSCs are responsible for chemoresistance, the contribution of CSC marker EpCAM to resistance to chemotherapy remains unresolved.Here we have demonstrated that ovarian cancers containing high levels of EpCAM have a significantly much lower probability of achieving overall responsive rates after first-line chemotherapy. In addition, multivariate analysis revealed that EpCAM expression is an independent risk factor for chemoresistance, indicating that EpCAM expression is a predictive biomarker of chemotherapeutic response. Consistent with these clinical observations, in vitro assays, we found that the subpopulation of EpCAM-positive ovarian cancer cells shows a significantly higher viability compared with EpCAM-negative cells in response to cisplatin treatment by preventing chemotherapy-induced apoptosis, which is regulated by EpCAM-Bcl-2 axis. Furthermore, in an in vivo mouse model, platinum agents preferentially eliminated EpCAM-negative cells in comparison with EpCAM-positive cells, suggesting that the remaining subpopulation of EpCAM-positive cells contributes to tumor recurrence after chemotherapy. Finally, we also found that an increased expression of EpCAM is associated with poor prognosis in ovarian cancer patients.Our findings highlight the clinical significance of EpCAM in the resistance to chemotherapy and provide a rationale for EpCAM-targeted therapy to improve chemoresistance. Targeting EpCAM should be a promising approach to effectively extirpate the CSCs as the putative root of ovarian cancer.

Social, structural, behavioral and clinical factors influencing retention in Pre-Exposure Prophylaxis (PrEP) care in Mississippi.

PubMed

Arnold, Trisha; Brinkley-Rubinstein, Lauren; Chan, Philip A; Perez-Brumer, Amaya; Bologna, Estefany S; Beauchamps, Laura; Johnson, Kendra; Mena, Leandro; Nunn, Amy

2017-01-01

Pre-exposure prophylaxis (PrEP) is a biomedical intervention that can reduce rates of HIV transmission when taken once daily by HIV-negative individuals. Little is understood about PrEP uptake and retention in care among the populations most heavily impacted by the HIV epidemic, particularly among young men who have sex with men (YMSM) in the Deep South. Therefore, this study explored the structural, social, behavioral, and clinical factors that affect PrEP use and retention in care among YMSM in Jackson, Mississippi. Thirty MSM who were prescribed PrEP at an outpatient primary care clinic were interviewed and included 23 men who had been retained in PrEP care and seven who had not been retained. The mean age of participants was 26.6 years. Most (23) participants were African American. Major factors affecting PrEP use and retention in PrEP care included 1) structural factors such as cost and access to financial assistance for medications and clinical services; 2) social factors such as stigma and relationship status; 3) behavioral factors including sexual risk behaviors; and 4) clinical factors such as perceived and actual side effects. Many participants also discussed the positive spillover effects of PrEP use and reported that PrEP had a positive impact on their health. Four of the seven individuals who had not been retained re-enrolled in PrEP care after completing their interviews, suggesting that case management and ongoing outreach can enhance retention in PrEP care. Interventions to enhance retention in PrEP care among MSM in the Deep South will be most effective if they address the complex structural, social, clinical, and behavioral factors that influence PrEP uptake and retention in PrEP care.

EpCAM expression in primary tumour tissues and metastases: an immunohistochemical analysis.

PubMed

Spizzo, Gilbert; Fong, Dominic; Wurm, Martin; Ensinger, Christian; Obrist, Peter; Hofer, Carina; Mazzoleni, Guido; Gastl, Guenther; Went, Philip

2011-05-01

Epithelial cell adhesion molecule (EpCAM) is a cell surface protein with oncogenic features that is expressed on healthy human epithelia and corresponding malignant tumours. EpCAM expression frequently correlates with more aggressive tumour behaviour and new EpCAM-specific therapeutic agents have recently been approved for clinical use in patients with cancer. However, no consensus exists on how and when to evaluate EpCAM expression in patients with cancer. EpCAM expression was assessed by a well-established immunohistochemical staining protocol in 2291 primary tumour tissues and in 108 metastases using the EpCAM-specific antibody clone VU1D9. A total immunostaining score was calculated as the product of a proportion score and an intensity score. Four expression subgroups (no, weak, moderate and intense) were defined. As described previously, the term 'EpCAM overexpression' was reserved for tissues showing a total immunostaining score >4. EpCAM was highly expressed in most tumours of gastrointestinal origin and in some carcinomas of the genitourinary tract. However, hepatocellular carcinomas, clear cell renal cell cancer, urothelial cancer and squamous cell cancers were frequently EpCAM negative. EpCAM expression in breast cancer depended on the histological subtype; lobular histology usually showed no or weak expression. Most metastases were EpCAM positive and they frequently reflected the expression phenotype of the primary tumour. EpCAM expression was detected on adenocarcinomas of various primary sites. If EpCAM-specific antibodies are intended to be used in patients with cancer, we recommend prior immunohistochemical evaluation of EpCAM expression, particularly in patients with renal cell cancer, hepatocellular carcinoma, urothelial carcinoma, breast cancer and squamous cell carcinomas.

HIV Care Providers' Intentions to Prescribe and Actual Prescription of Pre-Exposure Prophylaxis to At-Risk Adolescents and Adults.

PubMed

Mullins, Tanya L Kowalczyk; Zimet, Gregory; Lally, Michelle; Xu, Jiahong; Thornton, Sarah; Kahn, Jessica A

2017-12-01

Pre-exposure prophylaxis (PrEP) is indicated for use in US adults, and little is known about clinician intentions to prescribe and actual prescription of PrEP to adolescents younger than 18. Fifty-six clinicians who care for HIV-infected and at-risk youth completed an anonymous online survey in 2014. Primary outcomes were (1) intentions to prescribe PrEP to adolescents and adults in four risk categories [men who have sex with men (MSM), transgender women, heterosexuals with multiple partners of unknown HIV status, heterosexuals with HIV-infected partners]; and (2) actual prescription of PrEP to adolescents and adults in these risk groups. Independent variables included clinician characteristics, experience prescribing nonoccupational postexposure prophylaxis, familiarity with and knowledge of PrEP and PrEP guidance, attitudes toward PrEP, and facilitating factors for prescribing PrEP and incorporation of PrEP guidance into practice. Variables associated with intention to prescribe ("very likely to prescribe" vs. other responses) and actual prescription of PrEP stratified by age and risk category were identified in logistic regression models. Mean age was 45.9 years (standard deviation 10.7); 64% were physicians. More clinicians reported high intention to prescribe PrEP to adult versus adolescent MSM (p = 0.02) and transgender women (p = 0.001). Variables associated with intention to prescribe and prescription of PrEP differed by age and risk category. In adolescents, those variables included positive beliefs, higher number of facilitating factors, and fewer barriers to PrEP prescription. Designing strategies based on these findings that address both facilitating factors and barriers to PrEP prescription may improve PrEP uptake by at-risk youth.

"I Did Not Want to Give Birth to a Child Who has HIV": Experiences Using PrEP During Pregnancy Among HIV-Uninfected Kenyan Women in HIV-Serodiscordant Couples.

PubMed

Pintye, Jillian; Beima-Sofie, Kristin M; Kimemia, Grace; Ngure, Kenneth; Trinidad, Susan Brown; Heffron, Renee A; Baeten, Jared M; Odoyo, Josephine; Mugo, Nelly; Bukusi, Elizabeth A; Kelley, Maureen C; John-Stewart, Grace C

2017-11-01

The perceptions, motivations, and beliefs of HIV-uninfected women about pre-exposure prophylaxis (PrEP) use during pregnancy can influence its uptake and adherence. This study elicited the views of HIV-uninfected women with personal experience taking PrEP during pregnancy. Qualitative interviews were conducted with HIV-uninfected women who had personal experience taking PrEP while pregnant. Semistructured interviews were conducted with 21 HIV-uninfected Kenyan women in HIV-serodiscordant couples enrolled in an open-label PrEP demonstration project who became pregnant while using PrEP and continued PrEP through their pregnancy. Interviews were audio-recorded and transcribed into English. A qualitative descriptive analysis was performed, using a constant comparison approach to identify key themes related to PrEP use in pregnancy. Desire to remain HIV uninfected and have an HIV-free infant were strong motivators influencing continued use of PrEP during pregnancy. Supporting HIV-infected partners and childbearing within an HIV-serodiscordant relationship were also motivators. Women had challenges distinguishing normal pregnancy symptoms from PrEP side effects and were concerned that observed side effects could be signs of danger for the infant related to PrEP exposure. Health care providers were important conduits of knowledge about PrEP, and continuity of PrEP providers throughout pregnancy facilitated adherence. HIV-uninfected women in HIV-serodiscordant couples were motivated to use PrEP during pregnancy to remain HIV uninfected and to have an HIV-free child but had concerns about side effects. Health care providers will be important for PrEP messaging and adherence support in this unique population.

PGE2 maintains the tone of the guinea pig trachea through a balance between activation of contractile EP1 receptors and relaxant EP2 receptors

PubMed Central

Säfholm, J; Dahlén, S-E; Delin, I; Maxey, K; Stark, K; Cardell, L-O; Adner, M

2013-01-01

Background and Purpose The guinea pig trachea (GPT) is commonly used in airway pharmacology. The aim of this study was to define the expression and function of EP receptors for PGE2 in GPT as there has been ambiguity concerning their role. Experimental Approach Expression of mRNA for EP receptors and key enzymes in the PGE2 pathway were assessed by real-time PCR using species-specific primers. Functional studies of GPT were performed in tissue organ baths. Key Results Expression of mRNA for the four EP receptors was found in airway smooth muscle. PGE2 displayed a bell-shaped concentration–response curve, where the initial contraction was inhibited by the EP1 receptor antagonist ONO-8130 and the subsequent relaxation by the EP2 receptor antagonist PF-04418948. Neither EP3 (ONO-AE5-599) nor EP4 (ONO-AE3-208) selective receptor antagonists affected the response to PGE2. Expression of COX-2 was greater than COX-1 in GPT, and the spontaneous tone was most effectively abolished by selective COX-2 inhibitors. Furthermore, ONO-8130 and a specific PGE2 antibody eliminated the spontaneous tone, whereas the EP2 antagonist PF-04418948 increased it. Antagonists of other prostanoid receptors had no effect on basal tension. The relaxant EP2 response to PGE2 was maintained after long-term culture, whereas the contractile EP1 response showed homologous desensitization to PGE2, which was prevented by COX-inhibitors. Conclusions and Implications Endogenous PGE2, synthesized predominantly by COX-2, maintains the spontaneous tone of GPT by a balance between contractile EP1 receptors and relaxant EP2 receptors. The model may be used to study interactions between EP receptors. PMID:22934927

Demographic differences in PrEP–related stereotypes: Implications for implementation

PubMed Central

Golub, Sarit. A.; Gamarel, Kristi E.; Surace, Anthony

2015-01-01

Qualitative interviews about pre-exposure prophylaxis (PrEP) stereotypes were conducted with a subsample of 160 MSM who participated in a PrEP messaging study. Negative stereotypes about PrEP users were identified by 80% of participants. Two types of stereotypes were most common: PrEP users are HIV-infected (and lying about it), and PrEP users are promiscuous and resistant to condom use. Participants’ identification of these stereotype categories differed significantly by demographic factors (i.e. race/ethnicity, education). Expanding access to PrEP requires recognizing potential differences in the experience or anticipation of PrEP-related stereotypes that might impact willingness to discuss PrEP with providers, friends, or partners. PMID:26143247

40 CFR 63.1316 - PET and polystyrene affected sources-emissions control provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 12 2012-07-01 2011-07-01 true PET and polystyrene affected sources... and Resins § 63.1316 PET and polystyrene affected sources—emissions control provisions. (a) The owner or operator of an affected source producing PET using a continuous process shall comply with...

40 CFR 63.1316 - PET and polystyrene affected sources-emissions control provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 12 2013-07-01 2013-07-01 false PET and polystyrene affected sources... Polymers and Resins § 63.1316 PET and polystyrene affected sources—emissions control provisions. (a) The owner or operator of an affected source producing PET using a continuous process shall comply with...

40 CFR 63.1316 - PET and polystyrene affected sources-emissions control provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 12 2014-07-01 2014-07-01 false PET and polystyrene affected sources... Polymers and Resins § 63.1316 PET and polystyrene affected sources—emissions control provisions. (a) The owner or operator of an affected source producing PET using a continuous process shall comply with...

Trichomonas vaginalis clinical isolates: cytoadherence and adherence to polystyrene, intrauterine device, and vaginal ring.

PubMed

Dos Santos, Odelta; Rigo, Graziela Vargas; Macedo, Alexandre José; Tasca, Tiana

2017-12-01

The parasitism by Trichomonas vaginalis is complex and in part is mediated by cytoadherence accomplished via five surface proteins named adhesins and a glycoconjugate called lipophosphoglycan (TvLPG). In this study, we evaluated the ability of T. vaginalis isolates to adhere to cells, plastic (polystyrene microplates), intrauterine device (IUD), and vaginal ring. Of 32 T. vaginalis isolates, 4 (12.5%) were strong adherent. The T. vaginalis isolates TV-LACM6 and TV-LACM14 (strong polystyrene-adherent) were also able to adhere to IUD and vaginal ring. Following chemical treatments, results demonstrated that the T. vaginalis components, lipophosphoglycan, cytoskeletal proteins, and surface molecules, were involved in both adherence to polystyrene and cytoadherence. The gene expression level from four adhesion proteins was highest in trophozoites adhered to cells than trophozoites adhered to the abiotic surface (polystyrene microplate). Our data indicate the major involvement of TvLPG in adherence to polystyrene, and that adhesins are important for cytoadherence. Furthermore, to our knowledge, this is the first report showing the T. vaginalis adherence to contraceptive devices, reaffirming its importance as pathogen among women in reproductive age.

Adsorption of Nanoplastics on Algal Photosynthesis

NASA Astrophysics Data System (ADS)

Turner, James; Bhattacharya, Priyanka; Lin, Sijie; Ke, Pu Chun

2010-03-01

The rapid accumulation of disposed plastics in the environment, especially in the Pacific Ocean, has become a global concern in recent years. Photo, chemical and physical degradations constantly fragment these plastics into a wide array of macroscopic to microscopic particles. As a result, marine organisms such as algae may be exposed to plastic particles through ingestion, adsorption and other forms of uptake. Such interactions, currently little understood, could potentially impact on the health state of the entire food chain. Here we report on polystyrene-algae interaction and its impact on algal photosynthesis. We first investigated the adsorption of polystyrene beads (20 nm) on a cellulose film coated on a 96-well plate. We derived a supralinear increase of the adsorption with the beads concentration for both positively and negatively charged polystyrene beads, with a saturation observed for the negatively charged polystyrene beads of concentration above 1.6 mg/mL. Using a bicarbonate indicator we discovered decreased carbon dioxide depletion due to polystyrene-algae binding. Since polystyrene beads also mediated algae aggregation, nanoplastics may alternatively be harnessed for waste water treatment.

Forming foam structures with carbon foam substrates

DOEpatents

Landingham, Richard L.; Satcher, Jr., Joe H.; Coronado, Paul R.; Baumann, Theodore F.

2012-11-06

The invention provides foams of desired cell sizes formed from metal or ceramic materials that coat the surfaces of carbon foams which are subsequently removed. For example, metal is located over a sol-gel foam monolith. The metal is melted to produce a metal/sol-gel composition. The sol-gel foam monolith is removed, leaving a metal foam.

Impact of insurance coverage on utilization of pre-exposure prophylaxis for HIV prevention.

PubMed

Patel, Rupa R; Mena, Leandro; Nunn, Amy; McBride, Timothy; Harrison, Laura C; Oldenburg, Catherine E; Liu, Jingxia; Mayer, Kenneth H; Chan, Philip A

2017-01-01

Pre-exposure prophylaxis (PrEP) can reduce U.S. HIV incidence. We assessed insurance coverage and its association with PrEP utilization. We reviewed patient data at three PrEP clinics (Jackson, Mississippi; St. Louis, Missouri; Providence, Rhode Island) from 2014-2015. The outcome, PrEP utilization, was defined as patient PrEP use at three months. Multivariable logistic regression was performed to determine the association between insurance coverage and PrEP utilization. Of 201 patients (Jackson: 34%; St. Louis: 28%; Providence: 28%), 91% were male, 51% were White, median age was 29 years, and 21% were uninsured; 82% of patients reported taking PrEP at three months. Insurance coverage was significantly associated with PrEP utilization. After adjusting for Medicaid-expansion and individual socio-demographics, insured patients were four times as likely to use PrEP services compared to the uninsured (OR: 4.49, 95% CI: 1.68-12.01; p = 0.003). Disparities in insurance coverage are important considerations in implementation programs and may impede PrEP utilization.

Inappropriate erythropoietin secretion in polycythemia vera

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chikkappa, G.; Burlington, H.; Chanana, A.D.

1977-01-01

A patient with classical polycythemia vera (PV) was found to have an inappropriately elevated serum erythropoietin (Ep) level. Investigations did not reveal any lesion or blood abnormality known to be associated with excessive Ep production and erythrocytosis. Sudden withdrawal of blood to reduce the Hb and Hct from 18.5 gm% and 56% to 13.6 gm% and 41.5%, respectively, resulted in an increment of serum Ep to abnormal level. With iron treatment there was a brisk return of Hb and Hct to prebleeding levels which was associated with reduction in the serum Ep. The inverse relationship between the EP and Hbmore » or Hct is inconsistent with the presence of excessive Ep-producing lesion. These results suggested that the threshold for Ep secretion from normal Ep-secreting tissue to Hb and Hct levels is set at an abnormal level. This patient's marrow cells when cultured in vitro in the absence of Ep, unlike other PV patients' (except one) marrow cells, did not grow erythroid colonies. In the presence of Ep, however, the colonies comparable to those formed from normal marrow cultures were obtained. These results suggested that his marrow erythropoietic cells were neither Ep independent nor Ep-hyperresponsive, as has been suggested by some investigators for erythropoiesis in PV. This patient presents phenomena that hitherto have not been reported.« less

Misoprostol, an anti-ulcer agent and PGE2 receptor agonist, protects against cerebral ischemia.

PubMed

Li, Jun; Liang, Xibin; Wang, Qian; Breyer, Richard M; McCullough, Louise; Andreasson, Katrin

2008-06-20

Induction of COX-2 activity in cerebral ischemia results in increased neuronal injury and infarct size. Recent studies investigating neurotoxic mechanisms of COX-2 demonstrate both toxic and paradoxically protective effects of downstream prostaglandin receptor signaling pathways. We tested whether misoprostol, a PGE(2) receptor agonist that is utilized clinically as an anti-ulcer agent and signals through the protective PGE(2) EP2, EP3, and EP4 receptors, would reduce brain injury in the murine middle cerebral artery occlusion-reperfusion (MCAO-RP) model. Administration of misoprostol, at the time of MCAO or 2h after MCAO, resulted in significant rescue of infarct volume at 24 and 72h. Immunocytochemistry demonstrated dynamic regulation of the EP2 and EP4 receptors during reperfusion in neurons and endothelial cells of cerebral cortex and striatum, with limited expression of EP3 receptor. EP3-/- mice had no significant changes in infarct volume compared to control littermates. Moreover, administration of misoprostol to EP3+/+ and EP3-/- mice showed similar levels of infarct rescue, indicating that misoprostol protection was not mediated through the EP3 receptor. Taken together, these findings suggest a novel function for misoprostol as a protective agent in cerebral ischemia acting via the PGE(2) EP2 and/or EP4 receptors.

Photostability and Performance of Polystyrene Films Containing 1,2,4-Triazole-3-thiol Ring System Schiff Bases.

PubMed

Ali, Gassan Q; El-Hiti, Gamal A; Tomi, Ivan Hameed R; Haddad, Raghad; Al-Qaisi, Alaa J; Yousif, Emad

2016-12-09

Series of 4-(4-substituted benzylideneamino)-5-(3,4,5-trimethoxyphenyl)-4 H -1,2,4-triazole-3-thiols were synthesized and their structures were confirmed. The synthesized Schiff bases were used as photostabilizers for polystyrene against photodegradation. Polystyrene polymeric films containing synthesized Schiff bases (0.5% by weight) were irradiated (λ max = 365 nm and light intensity = 6.43 × 10 -9 ein·dm -3 ·s -1 ) at room temperature. The photostabilization effect of 1,2,4-triazole-3-thiols Schiff bases was determined using various methods. All the additives used enhanced the photostability of polystyrene films against irradiation compared with the result obtained in the absence of Schiff base. The Schiff bases can act as photostabilizers for polystyrene through the direct absorption of UV radiation and/or radical scavengers.

The effects of three commonly used extraction methods on the redox properties of extracellular polymeric substances from activated sludge.

PubMed

Lu, Qin; Chang, Ming; Yu, Zhen; Zhou, Shungui

2015-01-01

Recently, the redox properties of extracellular polymeric substances (EPS) have attracted the attention of scientists due to their associated environmental significance, such as organic pollutant (e.g. nitroaromatics and substituted nitrobenzenes) degradation and heavy metal (e.g. Cr(VI) and U(VI)) detoxification. Although the separation of EPS from bacterial cells is more often the first step in studies on EPS, and studies have demonstrated that extraction procedures can influence the sorption properties of EPS, few attempts have been made to investigate how separation methods affect the redox properties of the obtained EPS. In this study, three common extraction approaches, that is, centrifugation, formaldehyde+NaOH and ethylene diamine tetra-acetic acid (EDTA), were employed to extract EPS from activated sludge, and the obtained EPS were evaluated for their redox properties using electrochemical means, including cyclic voltammetry and chronoamperometry. In addition, spectroscopic techniques were utilized to explore the structural characteristics and composition of EPS. The results indicated that EPS extracted by EDTA clearly displayed reversible oxidation-reduction peaks in cyclic voltammograms and significantly higher electron-accepting capacity compared with EPS extracted using the other two approaches. Fourier transform infrared spectra and three-dimensional excitation-emission matrix spectra suggested that the EPS extracted with EDTA presented better redox properties because of the effective and efficient extraction of the humic substances, which are important components of the EPS of activated sludge. Therefore, extraction method has an impact on the composition and redox properties of EPS and should be chosen according to research purpose and EPS source.

Structure and biosynthesis of two exopolysaccharides produced by Lactobacillus johnsonii FI9785.

PubMed

Dertli, Enes; Colquhoun, Ian J; Gunning, A Patrick; Bongaerts, Roy J; Le Gall, Gwénaëlle; Bonev, Boyan B; Mayer, Melinda J; Narbad, Arjan

2013-11-01

Exopolysaccharides were isolated and purified from Lactobacillus johnsonii FI9785, which has previously been shown to act as a competitive exclusion agent to control Clostridium perfringens in poultry. Structural analysis by NMR spectroscopy revealed that L. johnsonii FI9785 can produce two types of exopolysaccharide: EPS-1 is a branched dextran with the unusual feature that every backbone residue is substituted with a 2-linked glucose unit, and EPS-2 was shown to have a repeating unit with the following structure: -6)-α-Glcp-(1-3)-β-Glcp-(1-5)-β-Galf-(1-6)-α-Glcp-(1-4)-β-Galp-(1-4)-β-Glcp-(1-. Sites on both polysaccharides were partially occupied by substituent groups: 1-phosphoglycerol and O-acetyl groups in EPS-1 and a single O-acetyl group in EPS-2. Analysis of a deletion mutant (ΔepsE) lacking the putative priming glycosyltransferase gene located within a predicted eps gene cluster revealed that the mutant could produce EPS-1 but not EPS-2, indicating that epsE is essential for the biosynthesis of EPS-2. Atomic force microscopy confirmed the localization of galactose residues on the exterior of wild type cells and their absence in the ΔepsE mutant. EPS2 was found to adopt a random coil structural conformation. Deletion of the entire 14-kb eps cluster resulted in an acapsular mutant phenotype that was not able to produce either EPS-2 or EPS-1. Alterations in the cell surface properties of the EPS-specific mutants were demonstrated by differences in binding of an anti-wild type L. johnsonii antibody. These findings provide insights into the biosynthesis and structures of novel exopolysaccharides produced by L. johnsonii FI9785, which are likely to play an important role in biofilm formation, protection against harsh environment of the gut, and colonization of the host.

"How I Wish This Thing Was Initiated 100 Years Ago!" Willingness to Take Daily Oral Pre-Exposure Prophylaxis among Men Who Have Sex with Men in Kenya.

PubMed

Karuga, Robinson Njoroge; Njenga, Serah Nduta; Mulwa, Rueben; Kilonzo, Nduku; Bahati, Prince; O'reilley, Kevin; Gelmon, Lawrence; Mbaabu, Stephen; Wachihi, Charles; Githuka, George; Kiragu, Michael

2016-01-01

The MSM population in Kenya contributes to 15% of HIV incidence. This calls for innovative HIV prevention interventions. Pre-exposure prophylaxis (PrEP) has been efficacious in preventing HIV among MSM in trials. There is limited data on the willingness to take daily oral PrEP in sub-Sahara Africa. PrEP has not been approved for routine use in most countries globally. This study aimed to document the willingness to take PrEP and barriers to uptake and adherence to PrEP in Kenya. The findings will inform the design of a PrEP delivery program as part of the routine HIV combination prevention. Eighty MSM were recruited in 2 Counties in December 2013. Quantitative data on sexual behaviour and willingness to take PrEP were collected using semi-structured interviews and analysed using SPSS. Qualitative data on knowledge of PrEP, motivators and barriers to uptake and adherence to PrEP were collected using in-depth interviews and FGDs and analysed using Nvivo. Analysis of data in willingness to take PrEP was conducted on the HIV negative participants (n = 55). 83% of MSM were willing to take daily oral HIV PrEP. Willingness to take PrEP was higher among the bi-sexual and younger men. Motivators for taking PrEP were the need to stay HIV negative and to protect their partners. History of poor medication adherence, fear of side effects and HIV stigma were identified as potential barriers to adherence. Participants were willing to buy PrEP at a subsidized price. There is willingness to take PrEP among MSM in Kenya and there is need to invest in targeted education and messaging on PrEP to enhance adherence, proper use and reduce stigma in the general population and among policy makers.

Ambiguity, ambivalence, and apprehensions of taking HIV-1 pre-exposure prophylaxis among male couples in San Francisco: a mixed methods study.

PubMed

Saberi, Parya; Gamarel, Kristi E; Neilands, Torsten B; Comfort, Megan; Sheon, Nicolas; Darbes, Lynae A; Johnson, Mallory O

2012-01-01

We conducted a mixed-methods study to examine serodiscordant and seroconcordant (HIV-positive/HIV-positive) male couples' PrEP awareness, concerns regarding health care providers offering PrEP to the community, and correlates of PrEP uptake by the HIV-negative member of the couple. Qualitative sub-study included one-on-one interviews to gain a deeper understanding of participants' awareness of and experiences with PrEP and concerns regarding health care providers offering PrEP to men who have sex with men (MSM). Quantitative analyses consisted of a cross-sectional study in which participants were asked about the likelihood of PrEP uptake by the HIV-negative member of the couple and level of agreement with health care providers offering PrEP to anyone requesting it. We used multivariable regression to examine associations between PrEP questions and covariates of interest and employed an inductive approach to identify key qualitative themes. Among 328 men (164 couples), 62% had heard about PrEP, but approximately one-quarter were mistaking it with post-exposure prophylaxis. The majority of participants had low endorsement of PrEP uptake and 40% were uncertain if health care providers should offer PrEP to anyone requesting it. Qualitative interviews with 32 men suggest that this uncertainty likely stems from concerns regarding increased risk compensation. Likelihood of future PrEP uptake by the HIV-negative member of the couple was positively associated with unprotected insertive anal intercourse but negatively correlated with unprotected receptive anal intercourse. Findings suggest that those at greatest risk may not be receptive of PrEP. Those who engage in moderate risk express more interest in PrEP; however, many voice concerns of increased risk behavior in tandem with PrEP use. Results indicate a need for further education of MSM communities and the need to determine appropriate populations in which PrEP can have the highest impact.

Structure and Biosynthesis of Two Exopolysaccharides Produced by Lactobacillus johnsonii FI9785*

PubMed Central

Dertli, Enes; Colquhoun, Ian J.; Gunning, A. Patrick; Bongaerts, Roy J.; Le Gall, Gwénaëlle; Bonev, Boyan B.; Mayer, Melinda J.; Narbad, Arjan

2013-01-01

Exopolysaccharides were isolated and purified from Lactobacillus johnsonii FI9785, which has previously been shown to act as a competitive exclusion agent to control Clostridium perfringens in poultry. Structural analysis by NMR spectroscopy revealed that L. johnsonii FI9785 can produce two types of exopolysaccharide: EPS-1 is a branched dextran with the unusual feature that every backbone residue is substituted with a 2-linked glucose unit, and EPS-2 was shown to have a repeating unit with the following structure: -6)-α-Glcp-(1–3)-β-Glcp-(1–5)-β-Galf-(1–6)-α-Glcp-(1–4)-β-Galp-(1–4)-β-Glcp-(1-. Sites on both polysaccharides were partially occupied by substituent groups: 1-phosphoglycerol and O-acetyl groups in EPS-1 and a single O-acetyl group in EPS-2. Analysis of a deletion mutant (ΔepsE) lacking the putative priming glycosyltransferase gene located within a predicted eps gene cluster revealed that the mutant could produce EPS-1 but not EPS-2, indicating that epsE is essential for the biosynthesis of EPS-2. Atomic force microscopy confirmed the localization of galactose residues on the exterior of wild type cells and their absence in the ΔepsE mutant. EPS2 was found to adopt a random coil structural conformation. Deletion of the entire 14-kb eps cluster resulted in an acapsular mutant phenotype that was not able to produce either EPS-2 or EPS-1. Alterations in the cell surface properties of the EPS-specific mutants were demonstrated by differences in binding of an anti-wild type L. johnsonii antibody. These findings provide insights into the biosynthesis and structures of novel exopolysaccharides produced by L. johnsonii FI9785, which are likely to play an important role in biofilm formation, protection against harsh environment of the gut, and colonization of the host. PMID:24019531

Technological parameters influence on the non-autoclaved foam concrete characteristics

NASA Astrophysics Data System (ADS)

Bartenjeva, Ekaterina; Mashkin, Nikolay

2017-01-01

Foam concretes are used as effective heat-insulating materials. The porous structure of foam concrete provides good insulating and strength properties that make them possible to be used as heat-insulating structural materials. Optimal structure of non-autoclaved foam concrete depends on both technological factors and properties of technical foam. In this connection, the possibility to manufacture heat-insulation structural foam concrete on a high-speed cavity plant with the usage of protein and synthetic foamers was estimated. This experiment was carried out using mathematical planning method, and in this case mathematical models were developed that demonstrated the dependence of operating performance of foam concrete on foaming and rotation speed of laboratory plant. The following material properties were selected for the investigation: average density, compressive strength, bending strength and thermal conductivity. The influence of laboratory equipment technological parameters on technical foam strength and foam stability coefficient in the cement paste was investigated, physical and mechanical properties of non-autoclaved foam concrete were defined based on investigated foam. As a result of investigation, foam concrete samples were developed with performance parameters ensuring their use in production. The mathematical data gathered demonstrated the dependence of foam concrete performance on the technological regime.

Role of foam drainage in producing protein aggregates in foam fractionation.

PubMed

Li, Rui; Zhang, Yuran; Chang, Yunkang; Wu, Zhaoliang; Wang, Yanji; Chen, Xiang'e; Wang, Tao

2017-10-01

It is essential to obtain a clear understanding of the foam-induced protein aggregation to reduce the loss of protein functionality in foam fractionation. The major effort of this work is to explore the roles of foam drainage in protein aggregation in the entire process of foam fractionation with bovine serum albumin (BSA) as a model protein. The results show that enhancing foam drainage increased the desorption of BSA molecules from the gas-liquid interface and the local concentration of desorbed molecules in foam. Therefore, it intensified the aggregation of BSA in foam fractionation. Simultaneously, it also accelerated the flow of BSA aggregates from rising foam into the residual solution along with the drained liquid. Because enhancing foam drainage increased the relative content of BSA molecules adsorbed at the gas-liquid interface, it also intensified the aggregation of BSA during both the defoaming process and the storage of the foamate. Furthermore, enhancing foam drainage more readily resulted in the formation of insoluble BSA aggregates. The results are highly important for a better understanding of foam-induced protein aggregation in foam fractionation. Copyright © 2017 Elsevier B.V. All rights reserved.

Sequential pyrolysis of plastic to recover polystyrene, HCl and terephthalic acid

DOEpatents

Evans, R.J.; Chum, H.L.

1995-11-07

A process is described for pyrolyzing plastic waste feed streams containing polyvinyl chloride, polyethylene terephthalate, polystyrene and polyethylene to recover polystyrene, HCl and terephthalic acid comprising: heating the plastic waste feed stream to a first temperature; adding an acid or base catalyst on an oxide or carbonate support; heating the plastic waste feed stream to pyrolyze polyethylene terephthalate and polyvinyl chloride; separating terephthalic acid or HCl; heating to a second temperature to pyrolyze polystyrene; separating styrene; heating the waste feed stream to a third temperature to pyrolyze polyethylene; and separating hydrocarbons. 83 figs.

Enhanced rhamnolipids production via efficient foam-control using stop valve as a foam breaker.

PubMed

Long, Xuwei; Shen, Chong; He, Ni; Zhang, Guoliang; Meng, Qin

2017-01-01

In this study, a stop valve was used as a foam breaker for dealing with the massive overflowing foam in rhamnolipid fermentation. As found, a stop valve at its tiny opening could break over 90% of the extremely stable rhamnolipid foam into enriched liquid when foam flows through the sharp gap in valve. The efficient foam-control by the stop valve considerably improved the rhamnolipid fermentation and significantly enhanced the rhamnolipid productivity by 83% compared to the regular fermentation. This efficient foam breaking was mainly achieved by a high shear rate in combination with fast separation of air from the collapsed foam. Altogether, the stop valve possessed a great activity in breaking rhamnolipid foam, and the involving mechanism holds the potential for developing efficient foam breakers for industrial rhamnolipid fermentation. Copyright © 2016. Published by Elsevier Ltd.

ZrP nanoplates based fire-fighting foams stabilizer

NASA Astrophysics Data System (ADS)

Zhang, Lecheng; Cheng, Zhengdong; Li, Hai

2015-03-01

Firefighting foam, as a significant innovation in fire protection, greatly facilitates extinguishments for liquid pool fire. Recently, with developments in LNG industry, high-expansion firefighting foams are also used for extinguishing LNG fire or mitigating LNG leakage. Foam stabilizer, an ingredient in fire-fighting foam, stabilizes foam bubbles and maintains desired foam volume. Conventional foam stabilizers are organic molecules. In this work, we developed a inorganic based ZrP (Zr(HPO4)2 .H2O, Zirconium phosphate) plates functionalized as firefighting foam stabilizer, improving firefighting foam performance under harsh conditions. Several tests were conducted to illustrate performance. The mechanism for the foam stabilization is also proposed. Artie McFerrin Department of Chemical Engineering, Texas A&M University, College Station, TX 77843, USA. Mary Kay O'Connor Process Safety Center, Texas A&M University, College Station, TX, 77843-3122

Foam, Foam-resin composite and method of making a foam-resin composite

NASA Technical Reports Server (NTRS)

MacArthur, Doug E. (Inventor); Cranston, John A. (Inventor)

1995-01-01

This invention relates to a foam, a foam-resin composite and a method of making foam-resin composites. The foam set forth in this invention comprises a urethane modified polyisocyanurate derived from an aromatic amino polyol and a polyether polyol. In addition to the polyisocyanurate foam, the composite of this invention further contains a resin layer, wherein the resin may be epoxy, bismaleimide, or phenolic resin. Such resins generally require cure or post-cure temperatures of at least 350.degree. F.

Exploratory development of foams from liquid crystal polymers

NASA Technical Reports Server (NTRS)

Chung, T. S.

1985-01-01

Two types of liquid crystal polymer (LCP) compositions were studied and evaluated as structural foam materials. One is a copolymer of 6-hydroxy-2-naphthoic acid, terephthalic acid, and p-acetoxyacetanilide (designed HNA/TA/AAA), and the other is a copolymer of p-hydroxybenzoic acid and 6-hydroxy-2-naphthoic acid (designated HBA/HNA). Experimental results showed that the extruded HNA/TA/AA foams have better mechanical quality and appearance than HBA/HNA foams. Heat treatment improved foam tensile strength and break elongation, but reduced their modulus. The injection molding results indicated that nitrogen foaming agents with a low-pressure process gave better void distribution in the injection molded LCP foams than those made by the conventional injection-molding machine and chemical blowing agents. However, in comparing LCP foams with other conventional plastic foams, HBA/HNA foams have better mechanical properties than foamed ABS and PS, but are comparable to PBT and inferior to polycarbonate foams, especially in heat-deflection temperature and impact resistance energy. These deficiencies are due to LCP molecules not having been fully oriented during the Union-Carbide low-pressure foaming process.

beta-Endorphin-induced analgesia is inhibited by synthetic analogs of beta-endorphin.

PubMed

Nicolas, P; Hammonds, R G; Li, C H

1984-05-01

Competitive antagonism of human beta-endorphin (beta h-EP)-induced analgesia by synthetic beta h-EP analogs with high in vitro opiate receptor binding to in vivo analgesic potency ratio has been demonstrated. A parallel shift of the dose-response curve for analgesia to the right was observed when either beta h-EP or [ Trp27 ] -beta h-EP was coinjected with various doses of [Gln8, Gly31 ]-beta h-EP-Gly-Gly-NH2, [Arg9,19,24,28,29]-beta h-EP, or [ Cys11 ,26, Phe27 , Gly31 ]-beta h-EP. It was estimated that the most potent antagonist, [Gln8, Gly31 ]-beta h-EP-Gly-NH2, is at least 200 times more potent than naloxone.

Knowledge of and interest in using preexposure prophylaxis for HIV prevention among men who have sex with men in Thailand.

PubMed

Sineath, R Craig; Finneran, Catherine; Sullivan, Patrick; Sanchez, Travis; Smith, Dawn K; Griensven, Frits van; Wimonsate, Wipas; Stephenson, Rob

2013-01-01

Little is known about HIV preexposure prophylaxis (PrEP) acceptability among men who have sex with men (MSM) in Thailand. The authors recruited an online convenience sample of Thai MSM (n = 404) to assess the knowledge of and interest in PrEP. Less than 7% had heard of PrEP; however, 35% indicated interest in PrEP after an explanation of its possible efficacy. Regression modeling demonstrated that HIV knowledge and risk behavior, but not demographics, are significant predictors of PrEP interest. More information and education about PrEP is necessary and more research is needed to examine PrEP acceptability and to inform the message for PrEP uptake.

How Stigma Surrounding the Use of HIV Preexposure Prophylaxis Undermines Prevention and Pleasure: A Call to Destigmatize "Truvada Whores".

PubMed

Calabrese, Sarah K; Underhill, Kristen

2015-10-01

Antiretroviral preexposure prophylaxis (PrEP; emtricitabine and tenofovir disoproxil fumarate [Truvada]) prevents HIV without penalizing sexual pleasure, and may even enhance pleasure (e.g., by reducing HIV-related anxiety). However, concern about sexual risk behavior increasing with PrEP use (risk compensation) and corresponding stereotypes of promiscuity may undermine PrEP's preventive potential. In this commentary, we review literature on sexual behavior change accompanying PrEP use, discuss risk compensation concerns and the "Truvada whore" stereotype as PrEP barriers, question the appropriateness of restricting PrEP access because of risk compensation, and consider sexual pleasure as a benefit of PrEP, an acceptable motive for seeking PrEP, and a core element of health. It is essential for science to trump stereotypes and sex-negative messaging in guiding decision-making affecting PrEP access and uptake.

Purification and properties of extracellular polysaccharide (EPS) antigens produced by different mould species.

PubMed

Notermans, S; Wieten, G; Engel, H W; Rombouts, F M; Hoogerhout, P; van Boom, J H

1987-02-01

Extracellular polysaccharide (EPS) antigens produced by different mould species were purified and partially characterized. Purification included (NH4)2SO4 treatment, Sepharose CL-4B column chromatography and Con A-sepharose chromatography. The EPS of Penicillium digitatum, Mucor racemosus and Cladosporium cladosporioides showed high antigenic capacities. Immunologically the EPS were partially genus-specific, but cross-reactivity was observed. The EPS antigens produced by species of Penicillium, Aspergillus repens and Geotrichum candidum lost their immunological activity upon heating (100 degrees C) at pH 1.8, while the EPS antigen of M. racemosus, Rhizopus oligosporus and C. cladosporioides were stable under the same conditions. The dominant monosaccharides present in the EPS antigen were mannose, galactose and glucose. The EPS obtained from cultures of M. racemosus and R. oligosporus also contained rhamnose. In the EPS produced by Penicillium spp. and A. repens the galactose residues were determined to be immunodominant.

Threefold Increase in PrEP Uptake Over Time with High Adherence Among Young Men Who Have Sex With Men in Chicago.

PubMed

Morgan, Ethan; Moran, Kevin; Ryan, Daniel T; Mustanski, Brian; Newcomb, Michael E

2018-05-04

The goal of this work is to better understand utilization and uptake of pre-exposure prophylaxis (PrEP) among young men who have sex with men (YMSM) and transgender women (TGW). We assessed trends and correlates of PrEP use and adherence across three time points of longitudinal data collection among 885 YMSM and TGW (aged 16-29) from the RADAR cohort in Chicago, 2015-2017. Past 6-month PrEP use increased across three visits: from 6.6 to 17.5%. In multivariable models, past 6-month PrEP use was significantly associated with participation in condomless sex, having more sexual partners, and older age. At least three-quarters of current PrEP users reported being ≥ 90% adherent to PrEP medication across all visits. Past 6-month PrEP use increased over time with those who participated in high-risk HIV behaviors also those most likely to have taken PrEP. As PrEP uptake continues to rise, more research will be needed to understand predictors of PrEP usage, as well as patterns of sexual behavior change following uptake.

Willingness to Self-Pay for Pre-exposure Prophylaxis in Men Who Have Sex With Men: A National Online Survey in Taiwan.

PubMed

Ko, Nai-Ying; Chen, Bo-Jie; Li, Chia-Wen; Ku, Wen-Wei; Hsu, Su-Ting

2016-04-01

High cost of pre-exposure prophylaxis (PrEP) is a major concern for acceptability. This study determined the willingness of men who have sex with men to self-pay for PrEP and factors associated with the likelihood of condom use if taking PrEP. The Taiwan 2014 MSM Online Sex Survey was conducted and data such as demographics, attitudes toward PrEP, and sexual behaviors in the previous 3 months were collected. Of the 1,151 MSM who participated, 56% were willing to take PrEP, but only 23% were willing to self-pay $340 for PrEP. Willingness to self-pay for PrEP was significantly associated with the previous receipt of nonoccupational post-exposure prophylaxis (adjusted odds ratio [AOR], 3.02, 95%CI [1.49, 6.12]), and positive attitudes toward PrEP (AOR, 3.02, 95%CI [2.19, 4.17]). Of MSM who are willing to use PrEP, 73.6% would maintain condom use if taking PrEP. If PrEP is made available in Taiwan, more efforts should be focused on increasing awareness of MSM who are practicing risky behaviors.

Thermal and rheological properties of a family of botryosphaerans produced by Botryosphaeria rhodina MAMB-05.

PubMed

Fonseca, Paulo R M S; Dekker, Robert F H; Barbosa, Aneli M; Silveira, Joana L M; Vasconcelos, Ana F D; Monteiro, Nilson K; Aranda-Selverio, Gabriel; da Silva, Maria de Lourdes Corradi

2011-09-02

Differential scanning calorimetry (DSC), thermogravimetry (TG) and Fourier-transform infra-red spectroscopy (FT-IR) analyses were performed to investigate changes in the physico-chemical properties of botryosphaerans, a family of exopolysaccharides (EPS) produced by the fungus Botryosphaeria rhodina MAMB-05 grown on glucose (EPS(GLC)), sucrose (EPS(SUC)) and fructose (EPS(FRU)). A slight endothermic transition and small mass loss attributable to the removal of water of hydration were observed in the DSC and TG analyses, respectively, for the three EPS samples. The FT-IR spectra confirmed no structural changes occurred during thermal treatment. Viscometry was utilized to obtain information on the rheological behaviour of the EPS in aqueous solutions. The Power Law and Cross Equations determined the natural pseudoplastic characteristics of the EPS. Comparatively, results obtained for EPS produced when B. rhodina MAMB-05 was grown on each of the three carbohydrate sources demonstrated similar apparent viscosity values for EPS(GLC) and EPS(SUC), while EPS(FRU) displayed the lowest apparent viscosity of the three botryosphaerans, suggesting a higher degree of ramification and lower Mw. EPS(GLC) and EPS(SUC) possessed similar degrees of ramification. The slight differences found in their viscosities can be explained by the differences in the type of branching among the three botryosphaerans, thus varying the strength of intermolecular interactions and consequently, consistency and viscosity. The physico-chemical studies of botryosphaerans represent the originality of this work, and the knowledge of these properties is an important criterion for potential applications.

Extrapyramidal Signs and Cognitive Subdomains in Alzheimer Disease.

PubMed

Park, Jin Hong; Myung, Woojae; Choi, Junbae; Kim, Sangha; Chung, Jae Won; Kang, Hyo Shin; Na, Duk L; Kim, Seong Yoon; Lee, Jae-Hong; Han, Seol-Heui; Choi, Seong Hye; Kim, Sang Yun; Kim, Doh Kwan

2016-07-01

Extrapyramidal signs (EPS), commonly observed in Alzheimer disease (AD), predict cognitive impairment and functional decline. This study investigated the association between EPS and five cognitive subdomains in a large number of participants with AD. Cross-sectional analyses of the nationwide Clinical Research of Dementia of South Korea (CREDOS) study, 2005-2012. Multicenter clinical settings. 1,737 participants with AD drawn from the CREDOS study. The EPS group was defined by the presence of at least one EPS based on neurologic examination. We assessed five cognitive subdomains: attention, language, visuospatial function, memory, and frontal/executive function using the Seoul Neuropsychological Screening Battery-Dementia version. The associations of EPS with each cognitive subdomain were analyzed with a multiple linear regression model after controlling for confounding factors: sex, age, years of education, severity of dementia (Clinical Dementia Rating Sum of Boxes), and white matter hyperintensities. 164 AD participants (9.4%) had EPS. AD participants with EPS showed lower performance compared with those without EPS in two cognitive subdomains: attention and visuospatial function. The language, memory, and frontal/executive subdomains did not differ between the EPS-positive and the EPS-negative groups. In addition, we found a significant moderating relationship between EPS and deep white matter hyperintensities on visuospatial function score. EPS in AD are associated with severe cognitive impairment in attention and visuospatial function. Careful screening for EPS in patients with AD may assist in prediction of cognitive profile. Copyright © 2016 American Association for Geriatric Psychiatry. Published by Elsevier Inc. All rights reserved.

HIV-negative male couples' attitudes about pre-exposure prophylaxis (PrEP) and using PrEP with a sexual agreement.

PubMed

Mitchell, Jason W; Lee, Ji-Young; Woodyatt, Cory; Bauermeister, José; Sullivan, Patrick; Stephenson, Rob

2016-08-01

One efficacious strategy to help prevent HIV is oral pre-exposure prophylaxis (PrEP), a daily regimen of antiretroviral treatment taken by HIV-negative individuals. Two of the recommendations of Centers for Disease Control and Prevention (CDC) guidelines for PrEP pertain to being in a relationship (i.e., male couples). Despite the recognition of how primary partners in male couples' relationships shape HIV risk and CDC's PrEP guidelines, there is a paucity of data that examine HIV-negative male couples' attitudes toward PrEP use and using PrEP with a sexual agreement. A sexual agreement is an explicit agreement made between two individuals about what sex and other related behaviors may occur within and outside of their relationship. In this qualitative study, we examine HIV-negative male couples' attitudes toward PrEP use and whether they thought PrEP could be integrated into a sexual agreement. Data for this study are drawn from couple-level interviews conducted in 2014 with 29 HIV-negative male couples who had a sexual agreement and were from Atlanta or Detroit. Both passive (e.g., flyers) and active (e.g., targeted Facebook advertisements) recruitment methods were used; the sample was stratified by agreement type. Thematic analysis was applied to identify the following themes regarding HIV-negative male couples' attitudes toward PrEP use: (1) PrEP and condom use; (2) concerns about PrEP (e.g., effectiveness, side effects, and promoting sexually risky behavior); and (3) accessibility of PrEP. Some thought PrEP could be a part of couples' agreement because it could help reduce sexual anxiety and sexual risk, and would help keep the couple safe. Others described PrEP use with an agreement as something for "others". Some were also concerned that incorporating PrEP could usurp the need for a sexual agreement in a couples' relationship. These themes highlight the need to improve informational messaging and promotion efforts about PrEP among HIV-negative male couples who may benefit from using it.

Immunolocalization of adipocytes and prostaglandin E2 and its four receptor proteins EP1, EP2, EP3, and EP4 in the caprine cervix during spontaneous term labor.

PubMed

Gu, Guosheng; Gao, Qian; Yuan, Xuejun; Huang, Libo; Ge, Lijiang

2012-05-01

The mechanisms of cervical ripening and dilation in mammals remain obscure. Information is lacking about the localization of prostaglandin E(2) (PGE(2))-producing cells and PGE(2) receptors (EP) in intrapartum cervix and whether cervical dilation at parturition is an active process. To reveal these mechanisms, immunolocalization of EP1-EP4 (official gene symbols PTGER1-PTGER4) and PGE(2)-producing cells in caprine cervix during nonpregnancy, pregnancy, and parturition was assayed by immunohistochemistry (IHC); the mRNA expression levels of PTGS2, PTGER2 (EP2), and PTGER4 (EP4) were determined using quantitative PCR; and the existence of adipocytes in the cervix at various stages was demonstrated with Oil Red O staining and IHC of perilipin A. The results suggested that in intrapartum caprine cervix staining of the PGE(2) was observed in the overall tissues, for example, blood vessels, canal or glandular epithelia, serosa, circular and longitudinal muscles, and stroma in addition to adipocytes; EP2 was detectable in all the tissues other than glandular epithelia; EP4 was strongly expressed in all the tissues other than serosa; EP1 was detected mainly in arterioles and canal or glandular epithelia; and EP3 was poorly expressed only in stroma, canal epithelia, and circular muscles. Little or no expression of EP2, EP3, and EP4 as well as PGE(2) in all cervical tissues was observed during nonpregnancy and pregnancy except for the strong expression of EP1 in canal or glandular epithelia during pregnancy. The mRNA expression levels of PTGS2, PTGER2, and PTGER4 were significantly higher in intrapartum than nonpregnant and midpregnant cervices (P < 0.01). Adipocytes appear only in the intrapartum cervix. These results support the concept that PGE(2) modulates specific functions in various anatomical structures of the caprine cervix at labor and the appearance of adipocytes at labor is likely related to caprine cervical dilation.

Ductility of polystyrene waste panel

NASA Astrophysics Data System (ADS)

Sulistyorini, Dewi; Yasin, Iskandar

2018-03-01

Polystyrene waste panel is one of alternative materials that uses polystyrene waste. This experiment is to utilize the polystyrene waste as a non structural panel to be evaluated the ductility. The specimen consisted of cement 250 kg/m3, polystyrene waste was as aggregate, water cement ratio was 0.4 and wire mesh diameter was 0.6 mm with the grid 6 mm × 6 mm placed on the top and bottom of the panels. The polystyrene panels were compressed at 2 MPa. Six specimens had dimension 80 cm length, 30 cm width and the thickness planned were two varieties, they were 0.5 cm and 1 cm. Flexural testing is used to examine load and deflection to measure the ductility. The load and the deflection showed that the maximum load for the specimen with 0.5 cm thickness is 0.4, 0.56 and 0.37. And for 1 cm thickness is 0.4, 0.36, 0.64. It shows that the thickness variation does not give effect on the maximum load. Result showed the average of Displacement Ductility Index of polystyrene waste panels with 0.5 cm thickness was 1.692 and for 1 cm thickness, the average was 4.043. So the average of the panel with 0.5 cm thickness planned is under 1.99 and the panel with 1 cm thickness planned is upper 3, therefore, it is considered imperative for adequate ductility.

Espresso coffee foam delays cooling of the liquid phase.

PubMed

Arii, Yasuhiro; Nishizawa, Kaho

2017-04-01

Espresso coffee foam, called crema, is known to be a marker of the quality of espresso coffee extraction. However, the role of foam in coffee temperature has not been quantitatively clarified. In this study, we used an automatic machine for espresso coffee extraction. We evaluated whether the foam prepared using the machine was suitable for foam analysis. After extraction, the percentage and consistency of the foam were measured using various techniques, and changes in the foam volume were tracked over time. Our extraction method, therefore, allowed consistent preparation of high-quality foam. We also quantitatively determined that the foam phase slowed cooling of the liquid phase after extraction. High-quality foam plays an important role in delaying the cooling of espresso coffee.

Generation of sclerosant foams by mechanical methods increases the foam temperature.

PubMed

Tan, Lulu; Wong, Kaichung; Connor, David; Fakhim, Babak; Behnia, Masud; Parsi, Kurosh

2017-08-01

Objective To investigate the effect of agitation on foam temperature. Methods Sodium tetradecyl sulphate and polidocanol were used. Prior to foam generation, the sclerosant and all constituent equipment were cooled to 4-25℃ and compared with cooling the sclerosant only. Foam was generated using a modified Tessari method. During foam agitation, the temperature change was measured using a thermocouple for 120 s. Results Pre-cooling all the constituent equipment resulted in a cooler foam in comparison with only cooling the sclerosant. A starting temperature of 4℃ produced average foam temperatures of 12.5 and 13.2℃ for sodium tetradecyl sulphate and polidocanol, respectively. It was also found that only cooling the liquid sclerosant provided minimal cooling to the final foam temperature, with the temperature 20 and 20.5℃ for sodium tetradecyl sulphate and polidocanol, respectively. Conclusion The foam generation process has a noticeable impact on final foam temperature and needs to be taken into consideration when creating foam.

Infiltrated carbon foam composites

NASA Technical Reports Server (NTRS)

Lucas, Rick D. (Inventor); Danford, Harry E. (Inventor); Plucinski, Janusz W. (Inventor); Merriman, Douglas J. (Inventor); Blacker, Jesse M. (Inventor)

2012-01-01

An infiltrated carbon foam composite and method for making the composite is described. The infiltrated carbon foam composite may include a carbonized carbon aerogel in cells of a carbon foam body and a resin is infiltrated into the carbon foam body filling the cells of the carbon foam body and spaces around the carbonized carbon aerogel. The infiltrated carbon foam composites may be useful for mid-density ablative thermal protection systems.

40 CFR 63.1318 - PET and polystyrene affected sources-testing and compliance demonstration provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 11 2011-07-01 2011-07-01 false PET and polystyrene affected sources...: Group IV Polymers and Resins § 63.1318 PET and polystyrene affected sources—testing and compliance... not apply and owners or operators are not required to comply with § 63.113. (b) PET affected sources...

40 CFR 63.1318 - PET and polystyrene affected sources-testing and compliance demonstration provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 12 2012-07-01 2011-07-01 true PET and polystyrene affected sources...: Group IV Polymers and Resins § 63.1318 PET and polystyrene affected sources—testing and compliance... not apply and owners or operators are not required to comply with § 63.113. (b) PET affected sources...

40 CFR 63.1318 - PET and polystyrene affected sources-testing and compliance demonstration provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true PET and polystyrene affected sources...: Group IV Polymers and Resins § 63.1318 PET and polystyrene affected sources—testing and compliance... not apply and owners or operators are not required to comply with § 63.113. (b) PET affected sources...

The properties of the wood-polystyrene interphase determined by inverse gas chromatography

Treesearch

John Simonsen; Zhenqiu Hong; Timothy G. Rials

1997-01-01

The properties of the interphase in wood-polymer composites are important determinants of the properties of the final composite. This study used inverse gas chromatography (IGC) to measure interphasal properties of composites of polystyrene and two types of wood fiber fillers and an inoranic substrate (CW) with varying amounts of surface coverage of polystyrene. Glass...

Foam property tests to evaluate the potential for longwall shield dust control.

PubMed

Reed, W R; Beck, T W; Zheng, Y; Klima, S; Driscoll, J

2018-01-01

Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration's lower coal mine respirable dust standard of 1.5 mg/m 3 . Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control.

Foam property tests to evaluate the potential for longwall shield dust control

PubMed Central

Reed, W.R.; Beck, T.W.; Zheng, Y.; Klima, S.; Driscoll, J.

2018-01-01

Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. PMID:29416179

Multiscale Analysis of Open-Cell Aluminum Foam for Impact Energy Absorption

NASA Astrophysics Data System (ADS)

Kim, Ji Hoon; Kim, Daeyong; Lee, Myoung-Gyu; Lee, Jong Kook

2016-09-01

The energy-absorbing characteristics of crash members in automotive collision play an important role in controlling the amount of damage to the passenger compartment. Aluminum foams have high strength-to-weight ratio and high deformability, thus good crashworthiness is expected while maintaining or even saving weights when foams are implemented in crash members. In order to investigate the effect of the open-cell aluminum foam fillers on impact performance and weight saving, a multiscale framework for evaluating the crashworthiness of aluminum foam-filled members is used. To circumvent the difficulties of mechanical tests on foams, a micromechanical model of the aluminum foam is constructed using the x-ray micro tomography and virtual tests are conducted for the micromechanical model to characterize the behavior of the foam. In the macroscale, the aluminum foam is represented by the crushable foam constitutive model, which is then incorporated into the impact test simulation of the foam-filled crash member. The multiscale foam-filled crash member model was validated for the high-speed impact test, which confirms that the material model characterized by the micromechanical approach represents the behavior of the open-cell foam under impact loading well. Finally, the crash member design for maximizing the energy absorption is discussed by investigating various designs from the foam-only structure to the hollow tube structure. It was found that the foam structure absorbs more energy than the hollow tube or foam-filled structure with the same weight.

A Cross-Sectional Online Survey of HIV Pre-Exposure Prophylaxis Adoption Among Primary Care Physicians.

PubMed

Blackstock, Oni J; Moore, Brent A; Berkenblit, Gail V; Calabrese, Sarah K; Cunningham, Chinazo O; Fiellin, David A; Patel, Viraj V; Phillips, Karran A; Tetrault, Jeanette M; Shah, Minesh; Edelman, E Jennifer

2017-01-01

Among health care providers, prescription of HIV pre-exposure prophylaxis (PrEP) has been low. Little is known specifically about primary care physicians (PCPs) with regard to PrEP awareness and adoption (i.e., prescription or referral), and factors associated with adoption. To assess PrEP awareness, PrEP adoption, and factors associated with adoption among PCPs. Cross-sectional online survey conducted in April and May 2015. Members of a national professional organization for academic primary care physicians (n = 266). PrEP awareness, PrEP adoption (ever prescribed or referred a patient for PrEP [yes/no]), provider and practice characteristics, and self-rated knowledge, attitudes, and beliefs associated with adoption. The survey response rate was 8.6 % (266/2093). Ninety-three percent of respondents reported prior awareness of PrEP. Of these, 34.9 % reported PrEP adoption. In multivariable analysis of provider and practice characteristics, compared with non-adopters, adopters were more likely to provide care to more than 50 HIV-positive patients (vs. 0, aOR = 6.82, 95 % CI 2.06-22.52). Compared with non-adopters, adopters were also more likely to report excellent, very good, or good self-rated PrEP knowledge (15.1 %, 33.7 %, 30.2 % vs. 2.5 %, 18.1 %, 23.8 %, respectively; p < 0.001) and to perceive PrEP as extremely safe (35.1 % vs. 10.7 %; p = 0.002). Compared with non-adopters, adopters were less likely to perceive PrEP as being moderately likely to increase risk behaviors ("risk compensation") (12.8 % vs. 28.8 %, p = 0.02). While most respondents were aware of PrEP, only one-third of PrEP-aware PCPs reported adoption. Adopters were more likely to have experience providing HIV care and to perceive PrEP as extremely safe, and were less likely to perceive PrEP use as leading to risk compensation. To enhance PCP adoption of PrEP, educational efforts targeting PCPs without HIV care experience should be considered, as well as training those with HIV care experience to be PrEP "clinical champions". Concerns about safety and risk compensation must also be addressed.

Suppression of inflammation with conditional deletion of the prostaglandin E2 EP2 receptor in macrophages and brain microglia.

PubMed

Johansson, Jenny U; Pradhan, Suraj; Lokteva, Ludmila A; Woodling, Nathaniel S; Ko, Novie; Brown, Holden D; Wang, Qian; Loh, Christina; Cekanaviciute, Egle; Buckwalter, Marion; Manning-Bog, Amy B; Andreasson, Katrin I

2013-10-02

Prostaglandin E2 (PGE2), a potent lipid signaling molecule, modulates inflammatory responses through activation of downstream G-protein coupled EP(1-4) receptors. Here, we investigated the cell-specific in vivo function of PGE2 signaling through its E-prostanoid 2 (EP2) receptor in murine innate immune responses systemically and in the CNS. In vivo, systemic administration of lipopolysaccharide (LPS) resulted in a broad induction of cytokines and chemokines in plasma that was significantly attenuated in EP2-deficient mice. Ex vivo stimulation of peritoneal macrophages with LPS elicited proinflammatory responses that were dependent on EP2 signaling and that overlapped with in vivo plasma findings, suggesting that myeloid-lineage EP2 signaling is a major effector of innate immune responses. Conditional deletion of the EP2 receptor in myeloid lineage cells in Cd11bCre;EP2(lox/lox) mice attenuated plasma inflammatory responses and transmission of systemic inflammation to the brain was inhibited, with decreased hippocampal inflammatory gene expression and cerebral cortical levels of IL-6. Conditional deletion of EP2 significantly blunted microglial and astrocytic inflammatory responses to the neurotoxin MPTP and reduced striatal dopamine turnover. Suppression of microglial EP2 signaling also increased numbers of dopaminergic (DA) neurons in the substantia nigra independent of MPTP treatment, suggesting that microglial EP2 may influence development or survival of DA neurons. Unbiased microarray analysis of microglia isolated from adult Cd11bCre;EP2(lox/lox) and control mice demonstrated a broad downregulation of inflammatory pathways with ablation of microglial EP2 receptor. Together, these data identify a cell-specific proinflammatory role for macrophage/microglial EP2 signaling in innate immune responses systemically and in brain.

Suppression of Inflammation with Conditional Deletion of the Prostaglandin E2 EP2 Receptor in Macrophages and Brain Microglia

PubMed Central

Johansson, Jenny U.; Pradhan, Suraj; Lokteva, Ludmila A.; Woodling, Nathaniel S.; Ko, Novie; Brown, Holden D.; Wang, Qian; Loh, Christina; Cekanaviciute, Egle; Buckwalter, Marion; Manning-Boğ, Amy B.

2013-01-01

Prostaglandin E2 (PGE2), a potent lipid signaling molecule, modulates inflammatory responses through activation of downstream G-protein coupled EP1–4 receptors. Here, we investigated the cell-specific in vivo function of PGE2 signaling through its E-prostanoid 2 (EP2) receptor in murine innate immune responses systemically and in the CNS. In vivo, systemic administration of lipopolysaccharide (LPS) resulted in a broad induction of cytokines and chemokines in plasma that was significantly attenuated in EP2-deficient mice. Ex vivo stimulation of peritoneal macrophages with LPS elicited proinflammatory responses that were dependent on EP2 signaling and that overlapped with in vivo plasma findings, suggesting that myeloid-lineage EP2 signaling is a major effector of innate immune responses. Conditional deletion of the EP2 receptor in myeloid lineage cells in Cd11bCre;EP2lox/lox mice attenuated plasma inflammatory responses and transmission of systemic inflammation to the brain was inhibited, with decreased hippocampal inflammatory gene expression and cerebral cortical levels of IL-6. Conditional deletion of EP2 significantly blunted microglial and astrocytic inflammatory responses to the neurotoxin MPTP and reduced striatal dopamine turnover. Suppression of microglial EP2 signaling also increased numbers of dopaminergic (DA) neurons in the substantia nigra independent of MPTP treatment, suggesting that microglial EP2 may influence development or survival of DA neurons. Unbiased microarray analysis of microglia isolated from adult Cd11bCre;EP2lox/lox and control mice demonstrated a broad downregulation of inflammatory pathways with ablation of microglial EP2 receptor. Together, these data identify a cell-specific proinflammatory role for macrophage/microglial EP2 signaling in innate immune responses systemically and in brain. PMID:24089506

Characteristics of thermoregulatory and febrile responses in mice deficient in prostaglandin EP1 and EP3 receptors

PubMed Central

Oka, Takakazu; Oka, Kae; Kobayashi, Takuya; Sugimoto, Yukihiko; Ichikawa, Atsushi; Ushikubi, Fumitaka; Narumiya, Shuh; Saper, Clifford B

2003-01-01

Previous studies have disagreed about whether prostaglandin EP1 or EP3 receptors are critical for producing febrile responses. We therefore injected lipopolysaccharide (LPS) at a variety doses (1 μg kg−1−1 mg kg−1) intraperitoneally (I.P.) into wild-type (WT) mice and mice lacking the EP1 or the EP3 receptors and measured changes in core temperature (Tc) by using telemetry. In WT mice, I.P. injection of LPS at 10 μg kg−1 increased Tc about 1 °C, peaking 2 h after injection. At 100 μg kg−1, LPS increased Tc, peaking 5–8 h after injection. LPS at 1 mg kg−1 decreased Tc, reaching a nadir at 5–8 h after injection. In EP1 receptor knockout (KO) mice injected with 10 μg kg−1 LPS, only the initial (< 40 min) increase in Tc was lacking; with 100 μg kg−1 LPS the mice showed no febrile response. In EP3 receptor KO mice, LPS decreased Tc in a dose- and time-dependent manner. Furthermore, in EP3 receptor KO mice subcutaneous injection of turpentine did not induce fever. Both EP1 and EP3 receptor KO mice showed a normal circadian cycle of Tc and brief hyperthermia following psychological stress (cage-exchange stress and buddy-removal stress). The present study suggests that both the EP1 and the EP3 receptors play a role in fever induced by systemic inflammation but neither EP receptor is involved in the circadian rise in Tc or psychological stress-induced hyperthermia in mice. PMID:12837930

Ependymin as a substrate for outgrowth of axons from cultured explants of goldfish retina.

PubMed

Schmidt, J T; Schmidt, R; Lin, W C; Jian, X Y; Stuermer, C A

1991-01-01

Ependymin, a prominent protein of the brain's extracellular fluid (ECF) was previously implicated in the consolidation of memory and in the activity-driven sharpening of the retinotectal projection. Because both these phenomena probably involve the growth and elaboration of appropriate synapses, we have tested whether ependymin can serve as a substrate for the growth of axons from goldfish retinal ganglion cells in a culture assay. Ependymin (Ep), laminin (LAM), polylysine (PL), and Concanavalin A (Con A) were plated on glass coverslips either uniformly or in striped patterns. Ep alone, either soluble or partly polymerized (by dropping calcium concentration and pH), was a good substrate for axonal outgrowth, as good or better than PL and Con A, but not as good as LAM. Neurites grew faster on LAM (71 microns/h) than on Ep (32 microns/h) or on PL (22 microns/h). Fasciculation was low on LAM, intermediate on Ep, and highest on PL. In exclusive side-by-side stripe assays, axons preferred LAM over Ep, but gave weak or no preference for Ep over Con A or PL. With stripes of LAM + Ep alongside pure LAM, the axons preferred the mixture of LAM + Ep. When antibodies to Ep were plated in stripes over continuous Ep substrate, the axons avoided the antibody-blocked stripes and grew on the Ep stripes. Antibodies to Ep did not, however, block growth on laminin substrates, nor did antibodies to LAM block growth on Ep. Dot blots and western blots showed very little cross recognition between the antibodies. Ependymin is a good substrate for neurite outgrowth, which is normally present in ECF, and adhesion to Ep is independent of LAM and possibly additive to it.

Primary care clinicians' experiences prescribing HIV pre-exposure prophylaxis at a specialized community health centre in Boston: lessons from early adopters.

PubMed

Krakower, Douglas S; Maloney, Kevin M; Grasso, Chris; Melbourne, Katherine; Mayer, Kenneth H

2016-01-01

An estimated 1.2 million Americans have indications for using antiretroviral pre-exposure prophylaxis (PrEP) to prevent HIV acquisition. For many of these at-risk individuals, the best opportunity to learn about and receive PrEP will be during routine visits to their generalist primary care clinicians. However, few generalist clinicians have prescribed PrEP, primarily because of practical concerns about providing PrEP in primary care settings. The experiences of specialized primary care clinicians who have prescribed PrEP can inform the feasibility of PrEP provision by generalists. During January to February 2015, 35 primary care clinicians at a community health centre in Boston that specializes in the care of sexual and gender minorities completed anonymous surveys about their experiences and practices with PrEP provision. Responses were analyzed with descriptive statistics. Thirty-two clinicians (response rate=91%) completed the surveys. Nearly all clinicians (97%) had prescribed PrEP (median 20 patients, interquartile range 11-33). Most clinicians reported testing and risk-reduction counselling practices concordant with U.S. Centers for Disease Control and Prevention guidelines for PrEP. Clinicians indicated that patients using PrEP experienced medication toxicities infrequently and generally reported high adherence. However, some clinicians' practices differed from guideline recommendations, and some clinicians observed patients with increased risk behaviours. Most clinicians (79%) rated PrEP provision as easy to accomplish, and 97% considered themselves likely to prescribe PrEP in the future. In a primary care clinic with specialized expertise in HIV prevention, clinicians perceived that PrEP provision to large numbers of patients was safe, feasible and potentially effective. Efforts to engage generalist primary care clinicians in PrEP provision could facilitate scale-up of this efficacious intervention.

Stigma and Conspiracy Beliefs Related to Pre-exposure Prophylaxis (PrEP) and Interest in Using PrEP Among Black and White Men and Transgender Women Who Have Sex with Men

PubMed Central

Kalichman, Seth C.; Price, Devon; Finneran, Stephanie; Allen, Aerielle; Maksut, Jessica

2018-01-01

The HIV/AIDS epidemic in the US continues to persist, in particular, among race, sexual orientation, and gender minority populations. Pre-exposure prophylaxis (PrEP), or using antiretroviral medications for HIV prevention, is an effective option, but uptake of PrEP has been slow. Sociocultural barriers to using PrEP have been largely underemphasized, yet have the potential to stall uptake and, therefore, warrant further understanding. In order to assess the relationships between potential barriers to PrEP (i.e., PrEP stigma and conspiracy beliefs), and interest in PrEP, Black men and transgender women who have sex with men (BMTW, N = 85) and White MTW (WMTW, N = 179) were surveyed at a gay pride event in 2015 in a large southeastern US city. Bivariate and multivariate logistic regression analyses were completed to examine factors associated with PrEP interest. Among the full sample, moderate levels of PrEP awareness (63%) and low levels of use (9%) were observed. Believing that PrEP is for people who are promiscuous (stigma belief) was strongly associated with lack of interest in using PrEP, and individuals who endorsed this belief were more likely to report sexual risk taking behavior. Conspiracy beliefs related to PrEP were reported among a large minority of the sample (42%) and were more frequently reported among BMTW than WMTW. Given the strong emphasis on the use of biomedical strategies for HIV prevention, addressing sociocultural barriers to PrEP access is urgently needed and failure to do so will weaken the potential benefits of biomedical prevention. PMID:28108878

Long-term effects of CuO nanoparticles on the surface physicochemical properties of biofilms in a sequencing batch biofilm reactor.

PubMed

Hou, Jun; You, Guoxiang; Xu, Yi; Wang, Chao; Wang, Peifang; Miao, Lingzhan; Li, Yi; Ao, Yanhui; Lv, Bowen; Yang, Yangyang

2016-11-01

In this study, we examined the long-term effects of copper oxide nanoparticles (CuO NPs) on the production and properties of EPS and the resulting variations in surface physicochemical characteristics of biofilms in a sequencing batch biofilm reactor. After exposure to 50 mg/L CuO NPs for 45 days, the protein (PRO) and polysaccharide (PS) contents in loosely bound EPS (LB-EPS) decreased as the production of LB-EPS decreased from 34.4 to 30 mg TOC/g EPS. However, the production of tightly bound EPS (TB-EPS) increased by 16.47 % as the PRO and PS contents increased. The content of humic-like substances (HS) increased significantly, becoming the predominant constituent in EPS with the presence of 50 mg/L CuO NPs. Furthermore, the results of three-dimensional excitation-emission fluorescence spectra confirmed the various changes in terms of the LB-EPS and TB-EPS contents after exposure to CuO NPs. Fourier transform infrared spectroscopy showed that the -OH and -NH 2 groups of proteins in EPS were involved in the reaction with CuO NPs. Moreover, the chronic exposure to CuO NPs induced a negative impact on the flocculating efficiency of EPS and on the hydrophobicity and aggregation ability of microbial cells. The PRO/PS ratios of different EPS fractions were consistent with their hydrophobicities (R 2 >0.98) and bioflocculating efficiencies (R 2 >0.95); however, there was no correlation with aggregation ability. Additionally, the presence of bovine serum albumin (BSA) prevented the physical contact between CuO NPs and EPS as a result of NP aggregation and electrostatic repulsion.

Prostaglandin receptor EP3 regulates cell proliferation and migration with impact on survival of endometrial cancer patients

PubMed Central

Zhu, Junyan; Trillsch, Fabian; Mayr, Doris; Kuhn, Christina; Rahmeh, Martina; Hofmann, Simone; Vogel, Marianne; Mahner, Sven; Jeschke, Udo; von Schönfeldt, Viktoria

2018-01-01

Background Prostaglandin E2 (PGE2) receptor 3 (EP3) regulates tumor cell proliferation, migration, and invasion in numerous cancers. The role of EP3 as a prognostic biomarker in endometrial cancer remains unclear. The primary aim of this study was to analyze the prognostic significance of EP3 expression in endometrial cancer. Methods We analyzed the EP3 expression of 140 endometrial carcinoma patients by immunohistochemistry. RL95-2 endometrial cancer cell line was chosen from four endometrial cancer cell lines (RL95-2, Ishikawa, HEC-1-A, and HEC-1-B) according to EP3 expression level. Treated with PGE2 and EP3 antagonist, RL95-2 cells were investigated by MTT, BrdU, and wound healing assay for functional assessment of EP3. Results EP3 staining differed significantly according to WHO tumor grading in both whole cohort (p = 0.01) and the subgroup of endometrioid carcinoma (p = 0.01). Patients with high EP3 expression in their respective tumors had impaired progression-free survival as well as overall survival in both cohorts above. EP3 expression in the overall cohort was identified as an independent prognostic marker for progression-free survival (HR 1.014, 95%CI 1.003-1.024, p = 0.01) when adjusted for age, stage, grading, and recurrence. Treatment with EP3 antagonists induced upregulation of estrogen receptor β and decreased activity of Ras and led to attenuated proliferation and migration of RL95-2 cells. Conclusions EP3 seems to play a crucial role in endometrial cancer progression. In the context of limited systemic treatment options for endometrial cancer, this explorative analysis identifies EP3 as a potential target for diagnostic workup and therapy. PMID:29416671

Prostaglandin receptor EP3 regulates cell proliferation and migration with impact on survival of endometrial cancer patients.

PubMed

Zhu, Junyan; Trillsch, Fabian; Mayr, Doris; Kuhn, Christina; Rahmeh, Martina; Hofmann, Simone; Vogel, Marianne; Mahner, Sven; Jeschke, Udo; von Schönfeldt, Viktoria

2018-01-02

Prostaglandin E2 (PGE2) receptor 3 (EP3) regulates tumor cell proliferation, migration, and invasion in numerous cancers. The role of EP3 as a prognostic biomarker in endometrial cancer remains unclear. The primary aim of this study was to analyze the prognostic significance of EP3 expression in endometrial cancer. We analyzed the EP3 expression of 140 endometrial carcinoma patients by immunohistochemistry. RL95-2 endometrial cancer cell line was chosen from four endometrial cancer cell lines (RL95-2, Ishikawa, HEC-1-A, and HEC-1-B) according to EP3 expression level. Treated with PGE2 and EP3 antagonist, RL95-2 cells were investigated by MTT, BrdU, and wound healing assay for functional assessment of EP3. EP3 staining differed significantly according to WHO tumor grading in both whole cohort (p = 0.01) and the subgroup of endometrioid carcinoma (p = 0.01). Patients with high EP3 expression in their respective tumors had impaired progression-free survival as well as overall survival in both cohorts above. EP3 expression in the overall cohort was identified as an independent prognostic marker for progression-free survival (HR 1.014, 95%CI 1.003-1.024, p = 0.01) when adjusted for age, stage, grading, and recurrence. Treatment with EP3 antagonists induced upregulation of estrogen receptor β and decreased activity of Ras and led to attenuated proliferation and migration of RL95-2 cells. EP3 seems to play a crucial role in endometrial cancer progression. In the context of limited systemic treatment options for endometrial cancer, this explorative analysis identifies EP3 as a potential target for diagnostic workup and therapy.

XAS analysis of iron and palladium bonded to a polysaccharide produced anaerobically by a strain of Klebsiella oxytoca.

PubMed

Arčon, Iztok; Paganelli, Stefano; Piccolo, Oreste; Gallo, Michele; Vogel-Mikuš, Katarina; Baldi, Franco

2015-09-01

Klebsiella oxytoca BAS-10 ferments citrate to acetic acid and CO2, and secretes a specific exopolysaccharide (EPS), which is able to bind different metallic species. These biomaterials may be used for different biotechnological purposes, including applications as innovative green biogenerated catalysts. In production of biogenerated Pd species, the Fe(III) as ferric citrate is added to anaerobic culture of K. oxytoca BAS-10, in the presence of palladium species, to increase the EPS secretion and improve Pd-EPS yield. In this process, bi-metallic (FePd-EPS) biomaterials were produced for the first time. The morphology of bi-metallic EPS, and the chemical state of the two metals in the FePd-EPS, are investigated by transmission electron microscopy, Fourier transform infra-red spectroscopy, micro-X-ray fluorescence, and X-ray absorption spectroscopy methods (XANES and EXAFS), and compared with mono-metallic Pd-EPS and Fe-EPS complexes. Iron in FePd-EPS is in the mineralized form of iron oxides/hydroxides, predominantly in the form of Fe(3+), with a small amount of Fe(2+) in the structure, most probably a mixture of different nano-crystalline iron oxides and hydroxides, as in mono-metallic Fe-EPS. Palladium is found as Pd(0) in the form of metallic nanoparticles with face-centred cubic structure in both bi-metallic (FePd-EPS) and mono-metallic (Pd-EPS) species. In bi-metallic species, Pd and Fe nanoparticles agglomerate in larger clusters, but they remain spatially separated. The catalytic ability of bi-metallic species (FePd-EPS) in a hydrodechlorination reaction is improved in comparison with mono-metallic Pd-EPS.

In vivo performance of novel soybean/gelatin-based bioactive and injectable hydroxyapatite foams

PubMed Central

Kovtun, Anna; Goeckelmann, Melanie J.; Niclas, Antje A.; Montufar, Edgar B.; Ginebra, Maria-Pau; Planell, Josep A.; Santin, Matteo; Ignatius, Anita

2015-01-01

Major limitations of calcium phosphate cements (CPCs) are their relatively slow degradation rate and the lack of macropores allowing the ingrowth of bone tissue. The development of self-setting cement foams has been proposed as a suitable strategy to overcome these limitations. In previous work we developed a gelatine-based hydroxyapatite foam (G-foam), which exhibited good injectability and cohesion, interconnected porosity and good biocompatibility in vitro. In the present study we evaluated the in vivo performance of the G-foam. Furthermore, we investigated whether enrichment of the foam with soybean extract (SG-foam) increased its bioactivity. G-foam, SG-foam and non-foamed CPC were implanted in a critical-size bone defect in the distal femoral condyle of New Zealand white rabbits. Bone formation and degradation of the materials were investigated after 4, 12 and 20 weeks using histological and biomechanical methods. The foams maintained their macroporosity after injection and setting in vivo. Compared to non-foamed CPC, cellular degradation of the foams was considerably increased and accompanied by new bone formation. The additional functionalization with soybean extract in the SG-foam slightly reduced the degradation rate and positively influenced bone formation in the defect. Furthermore, both foams exhibited excellent biocompatibility, implying that these novel materials may be promising for clinical application in non-loaded bone defects. PMID:25448348

In vivo performance of novel soybean/gelatin-based bioactive and injectable hydroxyapatite foams.

PubMed

Kovtun, Anna; Goeckelmann, Melanie J; Niclas, Antje A; Montufar, Edgar B; Ginebra, Maria-Pau; Planell, Josep A; Santin, Matteo; Ignatius, Anita

2015-01-01

Major limitations of calcium phosphate cements (CPCs) are their relatively slow degradation rate and the lack of macropores allowing the ingrowth of bone tissue. The development of self-setting cement foams has been proposed as a suitable strategy to overcome these limitations. In previous work we developed a gelatine-based hydroxyapatite foam (G-foam), which exhibited good injectability and cohesion, interconnected porosity and good biocompatibility in vitro. In the present study we evaluated the in vivo performance of the G-foam. Furthermore, we investigated whether enrichment of the foam with soybean extract (SG-foam) increased its bioactivity. G-foam, SG-foam and non-foamed CPC were implanted in a critical-size bone defect in the distal femoral condyle of New Zealand white rabbits. Bone formation and degradation of the materials were investigated after 4, 12 and 20weeks using histological and biomechanical methods. The foams maintained their macroporosity after injection and setting in vivo. Compared to non-foamed CPC, cellular degradation of the foams was considerably increased and accompanied by new bone formation. The additional functionalization with soybean extract in the SG-foam slightly reduced the degradation rate and positively influenced bone formation in the defect. Furthermore, both foams exhibited excellent biocompatibility, implying that these novel materials may be promising for clinical application in non-loaded bone defects. Copyright © 2014 Acta Materialia Inc. All rights reserved.

Polymer-Reinforced, Non-Brittle, Lightweight Cryogenic Insulation

NASA Technical Reports Server (NTRS)

Hess, David M.

2013-01-01

The primary application for cryogenic insulating foams will be fuel tank applications for fueling systems. It is crucial for this insulation to be incorporated into systems that survive vacuum and terrestrial environments. It is hypothesized that by forming an open-cell silica-reinforced polymer structure, the foam structures will exhibit the necessary strength to maintain shape. This will, in turn, maintain the insulating capabilities of the foam insulation. Besides mechanical stability in the form of crush resistance, it is important for these insulating materials to exhibit water penetration resistance. Hydrocarbon-terminated foam surfaces were implemented to impart hydrophobic functionality that apparently limits moisture penetration through the foam. During the freezing process, water accumulates on the surfaces of the foams. However, when hydrocarbon-terminated surfaces are present, water apparently beads and forms crystals, leading to less apparent accumulation. The object of this work is to develop inexpensive structural cryogenic insulation foam that has increased impact resistance for launch and ground-based cryogenic systems. Two parallel approaches will be pursued: a silica-polymer co-foaming technique and a post foam coating technique. Insulation characteristics, flexibility, and water uptake can be fine-tuned through the manipulation of the polyurethane foam scaffold. Silicate coatings for polyurethane foams and aerogel-impregnated polyurethane foams have been developed and tested. A highly porous aerogel-like material may be fabricated using a co-foam and coated foam techniques, and can insulate at liquid temperatures using the composite foam

A Novel Method for Preparing Auxetic Foam from Closed-cell Polymer Foam Based on Steam Penetration and Condensation (SPC) Process.

PubMed

Fan, Donglei; Li, Minggang; Qiu, Jian; Xing, Haiping; Jiang, Zhiwei; Tang, Tao

2018-05-31

Auxetic materials are a class of materials possessing negative Poisson's ratio. Here we establish a novel method for preparing auxetic foam from closed-cell polymer foam based on steam penetration and condensation (SPC) process. Using polyethylene (PE) closed-cell foam as an example, the resultant foams treated by SPC process present negative Poisson's ratio during stretching and compression testing. The effect of steam-treated temperature and time on the conversion efficiency of negative Poisson's ratio foam is investigated, and the mechanism of SPC method for forming re-entrant structure is discussed. The results indicate that the presence of enough steam within the cells is a critical factor for the negative Poisson's ratio conversion in the SPC process. The pressure difference caused by steam condensation is the driving force for the conversion from conventional closed-cell foam to the negative Poisson's ratio foam. Furthermore, the applicability of SPC process for fabricating auxetic foam is studied by replacing PE foam by polyvinyl chloride (PVC) foam with closed-cell structure or replacing water steam by ethanol steam. The results verify the universality of SPC process for fabricating auxetic foams from conventional foams with closed-cell structure. In addition, we explored potential application of the obtained auxetic foams by SPC process in the fabrication of shape memory polymer materials.

mdFoam+: Advanced molecular dynamics in OpenFOAM

NASA Astrophysics Data System (ADS)

Longshaw, S. M.; Borg, M. K.; Ramisetti, S. B.; Zhang, J.; Lockerby, D. A.; Emerson, D. R.; Reese, J. M.

2018-03-01

This paper introduces mdFoam+, which is an MPI parallelised molecular dynamics (MD) solver implemented entirely within the OpenFOAM software framework. It is open-source and released under the same GNU General Public License (GPL) as OpenFOAM. The source code is released as a publicly open software repository that includes detailed documentation and tutorial cases. Since mdFoam+ is designed entirely within the OpenFOAM C++ object-oriented framework, it inherits a number of key features. The code is designed for extensibility and flexibility, so it is aimed first and foremost as an MD research tool, in which new models and test cases can be developed and tested rapidly. Implementing mdFoam+ in OpenFOAM also enables easier development of hybrid methods that couple MD with continuum-based solvers. Setting up MD cases follows the standard OpenFOAM format, as mdFoam+ also relies upon the OpenFOAM dictionary-based directory structure. This ensures that useful pre- and post-processing capabilities provided by OpenFOAM remain available even though the fully Lagrangian nature of an MD simulation is not typical of most OpenFOAM applications. Results show that mdFoam+ compares well to another well-known MD code (e.g. LAMMPS) in terms of benchmark problems, although it also has additional functionality that does not exist in other open-source MD codes.

Composition and morphology characterization of exopolymeric substances produced by the PAH-degrading fungus of Mucor mucedo.

PubMed

Jia, Chunyun; Li, Xiaojun; Allinson, Graeme; Liu, Changfeng; Gong, Zongqiang

2016-05-01

To explore the role of exopolymeric substances (EPS) in the process of polycyclic aromatic hydrocarbons (PAH) biodegradation, the characteristics of EPS isolated from a PAH-degrading fungus were investigated firstly by spectrometric determination, microscopic observation, Fourier transform-infrared spectroscopy (FT-IR), and three-dimensional excitation-emission matrix fluorescence spectroscopy (3D-EEM), and then the PAH-degrading ability of isolated EPS was evaluated. The EPS compositions and morphology varied significantly with the extraction methods. EPS were mainly composed of proteins, carbohydrate, and humic-like substances, and the cation exchange resin (CER)-extracted EPS were granular while other EPS samples were all powders. Heating was the most effective treatment method, followed by the CER, centrifugation, and ultrasonication methods. However, 3D-EEM data demonstrated that heating treatment makes the mycelia lyse the most. Overall, therefore, the CER was the best EPS extraction method for Mucor mucedo (M. mucedo). The PAH degradation results indicated that 87 % of pyrene and 81 % of benzo[a]pyrene (B[a]P) were removed by M. mucedo over 12 days and 9 % more pyrene and 7 % more B[a]P were reduced after CER-extracted EPS addition of 465 mg l(-1). The investigation of EPS characterization and EPS enhancing PAH biodegradation is the premise for further in-depth exploration of the role of EPS contribution to PAH biodegradation.

Perceptions of and intentions to adopt HIV pre-exposure prophylaxis among black men who have sex with men in Los Angeles.

PubMed

Brooks, Ronald A; Landovitz, Raphael J; Regan, Rotrease; Lee, Sung-Jae; Allen, Vincent C

2015-12-01

This study assessed perceptions of pre-exposure prophylaxis (PrEP) and their association with PrEP adoption intention among a convenience sample of 224 low socioeconomic status black men who have sex with men (BMSM) residing in Los Angeles. Participants received educational information about PrEP and completed an in-person interview. More than half (60%) of the participants indicated a high intention to adopt PrEP. Younger BMSM (18-29 years) were twice as likely to report a high intention to adopt PrEP compared to older BMSM (30+ years). Only 33% of participants were aware of PrEP and no participant had ever used PrEP. Negative perceptions were associated with a lower PrEP adoption intention and included being uncomfortable taking an HIV medicine when HIV-negative and not knowing if there are long-term side effects of taking an HIV medication. These findings suggest that BMSM may adopt PrEP but that negative perceptions may limit its uptake among this population. In order to facilitate PrEP adoption among BMSM targeted educational and community awareness programmes are needed to provide accurate information on the benefits of PrEP and to address the negative perceptions of PrEP held by local BMSM populations. © The Author(s) 2015.

What people want from sex and preexposure prophylaxis.

PubMed

Grant, Robert M; Koester, Kimberly A

2016-01-01

As demand for preexposure prophylaxis (PrEP) increases, we are learning more about what people want from sex and PrEP. PrEP demand has reached a tipping point in the USA and is increasing rapidly. Although the primary benefit of PrEP use is biological, to reduce risk of HIV infection, PrEP users often express an alternative set of social and emotional benefits that are provided by PrEP. These collateral benefits of PrEP have salience, affect, and are experienced in the present, which are compelling drivers of human behavior. PrEP use has been associated with feeling safe during sex, usually in contrast to ruminations related to fear of HIV or intimate partner violence or control. PrEP can create empowerment, or agency, defined as the capacity and autonomy to act on one's own behalf, because it provides control over one's vulnerability to HIV and relief to women and men who may otherwise worry about whether their partners will use a condom, take antiretroviral therapy, or disclose their HIV status accurately. Planning for sexual and social goals in calm moments is also empowering. These highly desired collateral benefits of PrEP could be undermined, or eliminated, if PrEP is implemented in ways that are coercive or that foment fear of sexual risk compensation, drug resistance, toxicity, or moral judgment. Current PrEP implementation provides direct and indirect benefits that are highly desired.

Effect of pretreatment with epoxy compounds on the mechanical properties of bovine pericardial bioprosthetic materials.

PubMed

Xi, T; Liu, F; Xi, B

1992-07-01

Early failures of bovine pericardial heart valves are due to leaflet perforation, tearing and calcification. Since glutaraldehyde fixation has been shown to produce marked changes in leaflet mechanics and has been linked to development of calcification, bovine pericardium fixed with the four hydrophilic epoxy formulations and their mechanical properties are studied in this paper. We measured the thicknesses, shrinkage temperatures, stress relaxations and stress-strain curves of bovine pericardiums after different treatments with (1) non-treatment (fresh), (2) glutaraldehyde (GA), (3) epoxy compounds followed by the posttreatment with GA (EP 1#, EP 2#), and (4) epoxy compounds (EP 3# and EP 4#). Results of this study showed that the hydrophilic epoxy compounds are good crosslinking agents. There are no significant differences of shrinkage temperature and ultimate tensile stress among all tissue samples pretreated with GA, EP 1# and EP 2#. However, the stress relaxations of tissue-samples pretreated with epoxy compounds followed by the posttreatment with GA (EP 1# and EP 2#) are significantly slower than that pretreated with GA, and the strains at fracture of EP 1# and EP 2# are also significantly larger than that of GA or epoxy compounds. These facts show that the bovine pericardium pretreated with the epoxy compound followed by the posttreatment with GA (EP 1# and EP 2#) possesses greater tenacity and potential durability in dynamic stress.

Using Educational Prescriptions to Teach Medical Students Evidence-based Medicine

PubMed Central

Umscheid, Craig A.; Maenner, Matthew J.; Mull, Nikhil; Veesenmeyer, Angela F.; Farrar, John T.; Goldfarb, Stanley; Morrison, Gail; Albanese, Mark A.; Frohna, John G.; Feldstein, David A.

2018-01-01

Purpose To evaluate feasibility and impact of evidence-based medicine (EBM) educational prescriptions (EPs) in medical student clerkships. Methods Students answered clinical questions during clerkships using EPs, which guide learners through the “four As” of EBM. Epidemiology fellows graded EPs using a rubric. Feasibility was assessed using descriptive statistics and student and fellow end-of-study questionnaires, which also measured impact. In addition, for each EP, students reported patient impact. Impact on EBM skills was assessed by change in EP scores over time and scores on an EBM objective structured clinical exam (OSCE) that were compared to controls from the prior year. Results 117 students completed 402 EPs evaluated by 24 fellows. Average score was 7.34/9.00 (SD 1.58). 69 students (59%) and 21 fellows (88%) completed questionnaires. Most students thought EPs improved “Acquiring” and “Appraising.” Almost half thought EPs improved “Asking” and “Applying.” Fellows did not value grading EPs. For 18%of EPs, students reported a “change” or “potential change” in treatment. 56% “confirmed” treatment. EP scores increased by 1.27 (95% CI: 0.81–1.72). There were no differences in OSCE scores between cohorts. Conclusions Integrating EPs into clerkships is feasible and has impact, yet OSCEs were unchanged, and research fellows had limitations as evaluators. PMID:27075864

Preparing for pre-exposure prophylaxis: perceptions and readiness of Canadian pharmacists for the implementation of HIV pre-exposure prophylaxis.

PubMed

Yoong, Deborah; Naccarato, Mark; Sharma, Malika; Wilton, James; Senn, Heather; Tan, Darrell Hs

2016-07-01

Pre-exposure prophylaxis (PrEP) has been shown to reduce the risk of HIV transmission but has the potential to cause harm if not used properly. Pharmacists are well-positioned to foster PrEP's efficacy but little is known whether they would endorse it as an HIV prevention tool. The objective of the study was to determine Canadian HIV pharmacists' support for PrEP and to identify current barriers to promoting PrEP. Canadian pharmacists with experience in HIV care were invited to complete an online survey about their experiences, opinions, and learning needs regarding PrEP from December 2012 to January 2013. Among the 59 surveys received, 48 met criteria for final analysis. Overall, 33 (69%) respondents would provide education positively supporting the use of PrEP and 26 (54%) believed Health Canada should approve PrEP for use in Canada. Familiarity with the concept of PrEP and practice characteristics examined did not appear to be significantly associated with support for PrEP in univariable analyses. The principal barriers to promoting PrEP included inadequate drug coverage and insufficient knowledge to educate others. Many Canadian HIV pharmacists would endorse PrEP for high-risk patients; however, wider dissemination of information and lower drug costs may be needed to make PrEP more widely promoted. © The Author(s) 2015.

Exploratory survey of Florida pharmacists' experience, knowledge, and perception of HIV pre-exposure prophylaxis.

PubMed

Shaeer, Kristy M; Sherman, Elizabeth M; Shafiq, Sami; Hardigan, Patrick

2014-01-01

To assess Florida pharmacists' experience, knowledge, and perception of human immunodeficiency virus (HIV) pre-exposure prophylaxis (PrEP) and to identify areas for pharmacist training. Cross-sectional survey. Florida in March through July 2013. Florida pharmacists. In-person and online anonymous survey. Florida pharmacists' experience, knowledge, and perceptions of PrEP. 225 completed surveys were analyzed. Survey respondents were predominantly community pharmacists with mean age of 45.7 years and less than 20 years of experience. Only 22% of respondents reported dispensing PrEP to patients. Although 75% had completed HIV-related continuing education in the last 2 years, 63% were unaware of Centers for Disease Control and Prevention PrEP guidelines and 71% answered that they did not have sufficient knowledge to counsel patients with PrEP prescriptions. Importantly, 47% of respondents answered they were uncomfortable counseling patients about PrEP. By self-report, most pharmacists agreed PrEP leads to risky behavior (68%) and increased rates of sexually transmitted infections (65%), and is too costly to promote patient access (92%). Surveyed Florida pharmacists reported limited understanding of PrEP. As a widely accessible health care counseling resource, pharmacists are positioned to improve patient understanding, promote medication adherence, and enhance PrEP efficacy. Especially during PrEP implementation, when patients may receive PrEP prescriptions from non-HIV specialist prescribers, improving pharmacists' PrEP education presents a salient opportunity.

Dual-tasks and walking fast: relationship to extra-pyramidal signs in advanced Alzheimer disease.

PubMed

Camicioli, Richard; Bouchard, Thomas; Licis, Lisa

2006-10-25

Extra-pyramidal signs (EPS) and cadence predicted falls risk in patients with advanced Alzheimer disease (AD). Dual task performance predicts falls with variable success. Dual-task performance and walking fast were examined in advanced AD patients with EPS (EPS+, >3 modified Unified Parkinson's Disease Rating Scale [UPDRS] signs) or without EPS (EPS-, three or less UPDRS signs). Demographics, mental and functional status, behavioral impairment, EPS, and quantitative gait measures (GaitRite) were determined. The effects of an automatic dual-task (simple counting) and of walking fast on spatial and temporal gait characteristics were compared between EPS+ and EPS- subjects using a repeated measures design. Cadence decreased, while stride time, swing time and variability in swing time increased with the dual task. Results were insignificant after adjusting for secondary task performance. With walking fast, speed, cadence and stride length increased while stride time, swing time and double support time decreased. Although EPS+ subjects were slower and had decreased stride length, dual task and walking fast effects did not differ from EPS- subjects. Patient characteristics, the type of secondary task and the specific gait measures examined vary in the literature. In this moderately to severely demented population, EPS did not affect "unconscious" (dual task) or "conscious" (walking fast) gait modulation. Given their high falls risk, and retained ability to modulate walking, EPS+ AD patients may be ideal candidates for interventions aimed at preventing falls.

Success rates of single-dose methotrexate and additional dose requirements among women with first and previous ectopic pregnancies.

PubMed

Cirik, Derya Akdag; Kinay, Tugba; Keskin, Ugur; Ozden, Eda; Altay, Metin; Gelisen, Orhan

2016-04-01

To compare the success of the single-dose methotrexate regimen and the requirement for a second or third dose of methotrexate between women with their first ectopic pregnancy (EP) and those with previous EP. In a retrospective cohort study, data were analyzed from women treated for EP by single-dose methotrexate at a Turkish tertiary referral center between January 2010 and December 2013. Data were compared between women with at least one previous EP and those with their first EP. The success rate of the protocol in the first and previous EP groups was similar: 93.0% (320/344) and 87.3% (48/55), respectively. History of previous EP was not a predictor of treatment failure. However, the requirement for additional methotrexate doses was significantly higher in the previous EP group (16/48 [33.4%]) than in the first EP group (55/320 [17.2%]; P=0.03). Multivariate analysis showed that history of tubal surgery (P=0.006) and initial levels of the β-subunit of human chorionic gonadotropin (P=0.001) were significant predictors of treatment failure. Although the single-dose regimen had similar success rates in the previous EP and first EP groups, additional doses of methotrexate were more frequently required in the previous EP group. Copyright © 2015 International Federation of Gynecology and Obstetrics. Published by Elsevier Ireland Ltd. All rights reserved.

Magnetic graphene oxide-polystyrene and magnetic activated carbon-polystyrene nanocomposites as sorbents for bisphenol A.

NASA Astrophysics Data System (ADS)

Rekos, Kyriazis; Kampouraki, Zoi Christina; Samanidou, Victoria; Deliyanni, Eleni

2016-04-01

Magnetic graphene oxide-polystyrene and magnetic activated carbon-polystyrene nanocomposites as sorbents for bisphenol A. Kyriazis Rekos1, Zoi Christina Kampouraki1, Victoria Samanidou2, Eleni Deliyanni1 1 Laboratory of General and Inorganic Chemical Technology, Department of Chemistry, Aristotle University of Thessaloniki, GR-541 24 Thessaloniki, Greece 2 Laboratory of Analytical Chemistry, Department of Chemistry, Aristotle University of Thessaloniki, GR-541 24 Thessaloniki, Greece The aim of this work was to prepare and characterize novel composites of magnetic activated carbon or magnetic graphene oxide with polystyrene (GO/PSm), through one step simple and effective route. Μagnetite nanoparticles, prepared in the laboratory, were dispersed in the presence of activated carbon (C) or graphene oxide (GO) in a polystyrene (PS) solution in dimethylformamide, at elevated temperature, for the fabrication of the magnetite-Carbon-PS (C-PSm) and magnetite- Graphene Oxide-PS (GO-PSm) hybrid-nanoparticles. For comparison, C-PS and GO-PS composites were also prepared in the same route. The nanocomposites were tested for their sorption ability for an endocrine disruptor, bisphenol A. The effect of solution pH, initial concentration, contact time and temperature were examined. The magnetic graphite oxide-polystyrene presented higher adsorption capacity (100 mg/g) than the non magnetic composites (70 mg/g), as well as than initial graphite oxide (20 mg/g). FTIR, XRD, BET, TGA, VSM and SEM were performed in order to investigate the role of the PS on the better adsorption performance of the mGO-PS nanocomposites. The characterization with these techniques revealed the possible interactions of the surface functional groups of activated carbon and/or graphite oxide with polystyrene that resulted in the better performance of the magnetic nanocomposites for bisphenol A adsorption.

Randomized Clinical Trial of Sodium Polystyrene Sulfonate for the Treatment of Mild Hyperkalemia in CKD.

PubMed

Lepage, Laurence; Dufour, Anne-Claude; Doiron, Jessica; Handfield, Katia; Desforges, Katherine; Bell, Robert; Vallée, Michel; Savoie, Michel; Perreault, Sylvie; Laurin, Louis-Philippe; Pichette, Vincent; Lafrance, Jean-Philippe

2015-12-07

Hyperkalemia affects up to 10% of patients with CKD. Sodium polystyrene sulfonate has long been prescribed for this condition, although evidence is lacking on its efficacy for the treatment of mild hyperkalemia over several days. This study aimed to evaluate the efficacy of sodium polystyrene sulfonate in the treatment of mild hyperkalemia. In total, 33 outpatients with CKD and mild hyperkalemia (5.0-5.9 mEq/L) in a single teaching hospital were included in this double-blind randomized clinical trial. We randomly assigned these patients to receive either placebo or sodium polystyrene sulfonate of 30 g orally one time per day for 7 days. The primary outcome was the comparison between study groups of the mean difference of serum potassium levels between the day after the last dose of treatment and baseline. The mean duration of treatment was 6.9 days. Sodium polystyrene sulfonate was superior to placebo in the reduction of serum potassium levels (mean difference between groups, -1.04 mEq/L; 95% confidence interval, -1.37 to -0.71). A higher proportion of patients in the sodium polystyrene sulfonate group attained normokalemia at the end of their treatment compared with those in the placebo group, but the difference did not reach statistical significance (73% versus 38%; P=0.07). There was a trend toward higher rates of electrolytic disturbances and an increase in gastrointestinal side effects in the group receiving sodium polystyrene sulfonate. Sodium polystyrene sulfonate was superior to placebo in reducing serum potassium over 7 days in patients with mild hyperkalemia and CKD. Copyright © 2015 by the American Society of Nephrology.

Randomized Clinical Trial of Sodium Polystyrene Sulfonate for the Treatment of Mild Hyperkalemia in CKD

PubMed Central

Lepage, Laurence; Dufour, Anne-Claude; Doiron, Jessica; Handfield, Katia; Desforges, Katherine; Bell, Robert; Vallée, Michel; Savoie, Michel; Perreault, Sylvie; Laurin, Louis-Philippe; Pichette, Vincent

2015-01-01

Background and objectives Hyperkalemia affects up to 10% of patients with CKD. Sodium polystyrene sulfonate has long been prescribed for this condition, although evidence is lacking on its efficacy for the treatment of mild hyperkalemia over several days. This study aimed to evaluate the efficacy of sodium polystyrene sulfonate in the treatment of mild hyperkalemia. Design, setting, participants, & measurements In total, 33 outpatients with CKD and mild hyperkalemia (5.0–5.9 mEq/L) in a single teaching hospital were included in this double–blind randomized clinical trial. We randomly assigned these patients to receive either placebo or sodium polystyrene sulfonate of 30 g orally one time per day for 7 days. The primary outcome was the comparison between study groups of the mean difference of serum potassium levels between the day after the last dose of treatment and baseline. Results The mean duration of treatment was 6.9 days. Sodium polystyrene sulfonate was superior to placebo in the reduction of serum potassium levels (mean difference between groups, −1.04 mEq/L; 95% confidence interval, −1.37 to −0.71). A higher proportion of patients in the sodium polystyrene sulfonate group attained normokalemia at the end of their treatment compared with those in the placebo group, but the difference did not reach statistical significance (73% versus 38%; P=0.07). There was a trend toward higher rates of electrolytic disturbances and an increase in gastrointestinal side effects in the group receiving sodium polystyrene sulfonate. Conclusions Sodium polystyrene sulfonate was superior to placebo in reducing serum potassium over 7 days in patients with mild hyperkalemia and CKD. PMID:26576619

30 CFR 250.211 - What must the EP include?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What must the EP include? 250.211 Section 250.211 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT OF... Information Contents of Exploration Plans (ep) § 250.211 What must the EP include? Your EP must include the...

Microcalorimetric and potentiometric titration studies on the adsorption of copper by extracellular polymeric substances (EPS), minerals and their composites.

PubMed

Fang, Linchuan; Huang, Qiaoyun; Wei, Xing; Liang, Wei; Rong, Xinming; Chen, Wenli; Cai, Peng

2010-08-01

Equilibrium adsorption experiments, isothermal titration calorimetry and potentiometric titration techniques were employed to investigate the adsorption of Cu(II) by extracellular polymeric substances (EPS) extracted from Pseudomonas putida X4, minerals (montmorillonite and goethite) and their composites. Compared with predicted values of Cu(II) adsorption on composites, the measured values of Cu(II) on EPS-montmorillonite composite increased, however, those on EPS-goethite composite decreased. Potentiometric titration results also showed that more surface sites were observed on EPS-montmorillonite composite and less reactive sites were found on EPS-goethite composite. The adsorption of Cu(II) on EPS molecules and their composites with minerals was an endothermic reaction, while that on minerals was exothermic. The positive values of enthalpy change (Delta H) and entropy change (DeltaS) for Cu(II) adsorption on EPS and mineral-EPS composites indicated that Cu(II) mainly interacts with carboxyl and phosphoryl groups as inner-sphere complexes on EPS molecules and their composites with minerals. (c) 2010 Elsevier Ltd. All rights reserved.

Framing HIV Pre-Exposure Prophylaxis (PrEP) for the General Public: How Inclusive Messaging May Prevent Prejudice from Diminishing Public Support.

PubMed

Calabrese, Sarah K; Underhill, Kristen; Earnshaw, Valerie A; Hansen, Nathan B; Kershaw, Trace S; Magnus, Manya; Krakower, Douglas S; Mayer, Kenneth H; Betancourt, Joseph R; Dovidio, John F

2016-07-01

Strategic framing of public messages about HIV pre-exposure prophylaxis (PrEP) may influence public support for policies and programs affecting access. This survey study examined how public attitudes toward PrEP differed based on the social group PrEP was described as benefiting ("beneficiary") and the moderating effect of prejudice. Members of the general public (n = 154) recruited online were randomly assigned to three beneficiary conditions: general population, gay men, or Black gay men. All participants received identical PrEP background information before completing measures of PrEP attitudes (specifying beneficiary), racism, and heterosexism. Despite anticipating greater PrEP adherence among gay men and Black gay men and perceiving PrEP as especially beneficial to the latter, participants expressed lower support for policies/programs making PrEP affordable for these groups vs. the general population. This disparity in support was stronger among participants reporting greater prejudice. Inclusive framing of PrEP in public discourse may prevent prejudice from undermining implementation efforts.

A Closer Look at Racism and Heterosexism in Medical Students' Clinical Decision-Making Related to HIV Pre-Exposure Prophylaxis (PrEP): Implications for PrEP Education.

PubMed

Calabrese, Sarah K; Earnshaw, Valerie A; Krakower, Douglas S; Underhill, Kristen; Vincent, Wilson; Magnus, Manya; Hansen, Nathan B; Kershaw, Trace S; Mayer, Kenneth H; Betancourt, Joseph R; Dovidio, John F

2018-04-01

Social biases among healthcare providers could limit PrEP access. In this survey study of 115 US medical students, we examined associations between biases (racism and heterosexism) and PrEP clinical decision-making and explored prior PrEP education as a potential buffer. After viewing a vignette about a PrEP-seeking MSM patient, participants reported anticipated patient behavior (condomless sex, extra-relational sex, and adherence), intention to prescribe PrEP to the patient, biases, and background characteristics. Minimal evidence for racism affecting clinical decision-making emerged. In unadjusted analyses, heterosexism indirectly affected prescribing intention via all anticipated behaviors, tested as parallel mediators. Participants expressing greater heterosexism more strongly anticipated increased risk behavior and adherence problems, which were associated with lower prescribing intention. The indirect effect via condomless sex remained significant adjusting for background characteristics. Prior PrEP education did not buffer any indirect effects. Heterosexism may compromise PrEP provision to MSM and should be addressed in PrEP-related medical education.

Acceptability of Pre-Exposure Prophylaxis (PrEP) as an HIV prevention strategy: Barriers and facilitators to PrEP uptake among at-risk Peruvian populations

PubMed Central

Galea, Jerome T.; Kinsler, Janni J.; Salazar, Ximena; Lee, Sung-Jae; Giron, Maziel; Sayles, Jennifer N.; Cáceres, Carlos; Cunningham, William E.

2010-01-01

This study examined Pre-Exposure Prophylaxis (PrEP) acceptability among female sex workers, male-to-female transgendered persons, and men who have sex with men in Lima, Peru. Focus groups explored social issues associated with PrEP acceptability and conjoint analysis assessed preferences among eight hypothetical PrEP scenarios with varying attribute profiles and their relative impact on acceptability. Conjoint analysis revealed that PrEP acceptability ranged from 19.8 to 82.5 out of a possible score of 100 across the eight hypothetical PrEP scenarios. Out-of-pocket cost had the greatest impact on PrEP acceptability (25.2, p <0.001), followed by efficacy (21.4, p <0.001) and potential side effects (14.7, p <0.001). Focus group data supported these findings, and also revealed that potential sexual risk disinhibition, stigma and discrimination associated with PrEP use, and mistrust of health care professionals were also concerns. These issues will require careful attention when planning for PrEP roll-out if proven efficacious in ongoing clinical trials. PMID:21571973

Acceptability of Daily Use of Free Oral Pre-exposure Prophylaxis (PrEP) Among Transgender Women Sex Workers in Shenyang, China.

PubMed

Wang, Zixin; Lau, Joseph T F; Yang, Xueying; Cai, Yong; Gross, Danielle L; Ma, Tiecheng; Liu, Yan

2017-12-01

This study investigated the acceptability of daily use of free oral pre-exposure prophylaxis (PrEP) and associated factors among transgender women sex workers in Shenyang, China, following a briefing on PrEP. A total of 183 HIV negative or sero-status unknown participants completed the cross-sectional survey. The prevalence of acceptability of daily use of free oral PrEP was 61.2%. Adjusting for education level and monthly income, variables on negative attitudes toward PrEP (i.e., having concerns about the side-effects of PrEP) [Adjusted odds ratios (AOR): 0.26], perceived subjective norms (i.e., perceiving support from male partners to take PrEP) (AOR: 2.08), and perceived behavioral control (e.g., perceiving complete control over using PrEP) (AOR: 2.10-16.72) were significantly associated with acceptability of daily use of free oral PrEP. In addition, experiencing violence during sex work, perceived risk of contracting HIV from clients and probable anxiety were also significant. Future PrEP promotion campaigns should consider these factors.

Framing HIV Pre-Exposure Prophylaxis (PrEP) for the General Public: How Inclusive Messaging May Prevent Prejudice from Diminishing Public Support

PubMed Central

Calabrese, Sarah K.; Underhill, Kristen; Earnshaw, Valerie A.; Hansen, Nathan B.; Kershaw, Trace S.; Magnus, Manya; Krakower, Douglas S.; Mayer, Kenneth H.; Betancourt, Joseph R.; Dovidio, John F.

2016-01-01

Strategic framing of public messages about HIV pre-exposure prophylaxis (PrEP) may influence public support for policies and programs affecting access. This survey study examined how public attitudes toward PrEP differed based on the social group PrEP was described as benefiting (“beneficiary”) and the moderating effect of prejudice. Members of the general public (n = 154) recruited online were randomly assigned to three beneficiary conditions: general population, gay men, or Black gay men. All participants received identical PrEP background information before completing measures of PrEP attitudes (specifying beneficiary), racism, and heterosexism. Despite anticipating greater PrEP adherence among gay men and Black gay men and perceiving PrEP as especially beneficial to the latter, participants expressed lower support for policies/programs making PrEP affordable for these groups vs. the general population. This disparity in support was stronger among participants reporting greater prejudice. Inclusive framing of PrEP in public discourse may prevent prejudice from undermining implementation efforts. PMID:26891840

EpCAM-Independent Enrichment of Circulating Tumor Cells in Metastatic Breast Cancer.

PubMed

Schneck, Helen; Gierke, Berthold; Uppenkamp, Frauke; Behrens, Bianca; Niederacher, Dieter; Stoecklein, Nikolas H; Templin, Markus F; Pawlak, Michael; Fehm, Tanja; Neubauer, Hans

2015-01-01

Circulating tumor cells (CTCs) are the potential precursors of metastatic disease. Most assays established for the enumeration of CTCs so far-including the gold standard CellSearch-rely on the expression of the cell surface marker epithelial cell adhesion molecule (EpCAM). But, these approaches may not detect CTCs that express no/low levels of EpCAM, e.g. by undergoing epithelial-to-mesenchymal transition (EMT). Here we present an enrichment strategy combining different antibodies specific for surface proteins and extracellular matrix (ECM) components to capture an EpCAMlow/neg cell line and EpCAMneg CTCs from blood samples of breast cancer patients depleted for EpCAM-positive cells. The expression of respective proteins (Trop2, CD49f, c-Met, CK8, CD44, ADAM8, CD146, TEM8, CD47) was verified by immunofluorescence on EpCAMpos (e.g. MCF7, SKBR3) and EpCAMlow/neg (MDA-MB-231) breast cancer cell lines. To test antibodies and ECM proteins (e.g. hyaluronic acid (HA), collagen I, laminin) for capturing EpCAMneg cells, the capture molecules were first spotted in a single- and multi-array format onto aldehyde-coated glass slides. Tumor cell adhesion of EpCAMpos/neg cell lines was then determined and visualized by Coomassie/MitoTracker staining. In consequence, marginal binding of EpCAMlow/neg MDA-MB-231 cells to EpCAM-antibodies could be observed. However, efficient adhesion/capturing of EpCAMlow/neg cells could be achieved via HA and immobilized antibodies against CD49f and Trop2. Optimal capture conditions were then applied to immunomagnetic beads to detect EpCAMneg CTCs from clinical samples. Captured CTCs were verified/quantified by immunofluorescence staining for anti-pan-Cytokeratin (CK)-FITC/anti-CD45 AF647/DAPI. In total, in 20 out of 29 EpCAM-depleted fractions (69%) from 25 metastatic breast cancer patients additional EpCAMneg CTCs could be identified [range of 1-24 CTCs per sample] applying Trop2, CD49f, c-Met, CK8 and/or HA magnetic enrichment. EpCAMneg dual-positive (CKpos/CD45pos) cells could be traced in 28 out of 29 samples [range 1-480]. By single-cell array-based comparative genomic hybridization we were able to demonstrate the malignant nature of one EpCAMneg subpopulation. In conclusion, we established a novel enhanced CTC enrichment strategy to capture EpCAMneg CTCs from clinical blood samples by targeting various cell surface antigens with antibody mixtures and ECM components.

46 CFR 108.473 - Foam system components.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Foam system components. 108.473 Section 108.473 Shipping... EQUIPMENT Fire Extinguishing Systems Foam Extinguishing Systems § 108.473 Foam system components. (a) Each foam agent, each tank for a foam agent, each discharge outlet, each control, and each valve for the...

46 CFR 108.473 - Foam system components.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Foam system components. 108.473 Section 108.473 Shipping... EQUIPMENT Fire Extinguishing Systems Foam Extinguishing Systems § 108.473 Foam system components. (a) Each foam agent, each tank for a foam agent, each discharge outlet, each control, and each valve for the...

Initial Evaluation of Burn Characteristics of Phenolic Foam Runway Brake Arrestor Material

DTIC Science & Technology

1993-12-01

foam immersed in a jet fuel fire when extinguished using 3-percent Aqueous Film Forming Foam ( AFFF ). Three pool...extinguishment time of phenolic foam immersed in a jet fuel fire, using 3-percent Aqueous Film Forming Foam ( AFFF ) extinguishing agent. The wind was negligible...percent Aqueous Film Forming Foam ( AFFF ) agent. This project is an initial assessment of the fire safety of phenolic foam

Electrostatic Safety with Explosion Suppressant Foams.

DTIC Science & Technology

1983-03-01

the foam, and (2) sorption of alkylphenol type substances, present as oxidation inhibitors in the fuel, by the foam. It had been previously reported... alkylphenol type substances. The use of antistatic ingredients in the reticulated polyurethane foam was suggested as a means of minimizing static...foam with JP-4 are: o Removal of diethylhexyl phthalate from the foam. o Sorption of alkylphenol type compounds by the foam. Tne latter of these two

Impact of foamed matrix components on foamed concrete properties

NASA Astrophysics Data System (ADS)

Tarasenko, V. N.

2018-03-01

The improvement of the matrix foam structure by means of foam stabilizing additives is aimed at solving the technology-oriented problems as well as at the further improvement of physical and mechanical properties of cellular-concrete composites. The dry foam mineralization is the mainstream of this research. Adding the concrete densifiers, foam stabilizers and mineral powders reduces the drying shrinkage, which makes the foam concrete products technologically effective.

Foam-mat drying technology: A review.

PubMed

Hardy, Z; Jideani, V A

2017-08-13

This article reviews various aspects of foam-mat drying such as foam-mat drying processing technique, main additives used for foam-mat drying, foam-mat drying of liquid and solid foods, quality characteristics of foam-mat dried foods, and economic and technical benefits for employing foam-mat drying. Foam-mat drying process is an alternative method that allows the removal of water from liquid materials and pureed materials. In this drying process, a liquid material is converted into foam that is stable by being whipped after adding an edible foaming agent. The stable foam is then spread out in sheet or mat and dried by using hot air (40-90°C) at atmospheric pressure. Methyl cellulose (0.25-2%), egg white (3-20%), maltodextrin (0.5-05%), and gum Arabic (2-9%) are the commonly utilized additives for the foam-mat drying process at the given range, either combined together for their effectiveness or individual effect. The foam-mat drying process is suitable for heat sensitive, viscous, and sticky products that cannot be dried using other forms of drying methods such as spray drying because of the state of product. More interest has developed for foam-mat drying because of the simplicity, cost effectiveness, high speed drying, and improved product quality it provides.

Application of an Elongated Kelvin Model to Space Shuttle Foams

NASA Technical Reports Server (NTRS)

Sullivan, Roy M.; Ghosn, Louis J.; Lerch, Bradley A.

2009-01-01

The space shuttle foams are rigid closed-cell polyurethane foams. The two foams used most-extensively oil space shuttle external tank are BX-265 and NCFL4-124. Because of the foaming and rising process, the foam microstructures are elongated in the rise direction. As a result, these two foams exhibit a nonisotropic mechanical behavior. A detailed microstructural characterization of the two foams is presented. Key features of the foam cells are described and the average cell dimensions in the two foams are summarized. Experimental studies are also conducted to measure the room temperature mechanical response of the two foams in the two principal material directions (parallel to the rise and perpendicular to the rise). The measured elastic modulus, proportional limit stress, ultimate tensile strength, and Poisson's ratios are reported. The generalized elongated Kelvin foam model previously developed by the authors is reviewed and the equations which result from this model are summarized. Using the measured microstructural dimensions and the measured stiffness ratio, the foam tensile strength ratio and Poisson's ratios are predicted for both foams and are compared with the experimental data. The predicted tensile strength ratio is in close agreement with the measured strength ratio for both BX-265 and NCFI24-124. The comparison between the predicted Poisson's ratios and the measured values is not as favorable.

Foam Transport in Porous Media - A Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Z. F.; Freedman, Vicky L.; Zhong, Lirong

2009-11-11

Amendment solutions with or without surfactants have been used to remove contaminants from soil. However, it has drawbacks such that the amendment solution often mobilizes the plume, and its movement is controlled by gravity and preferential flow paths. Foam is an emulsion-like, two-phase system in which gas cells are dispersed in a liquid and separated by thin liquid films called lamellae. Potential advantages of using foams in sub-surface remediation include providing better control on the volume of fluids injected, uniformity of contact, and the ability to contain the migration of contaminant laden liquids. It is expected that foam can servemore » as a carrier of amendments for vadose zone remediation, e.g., at the Hanford Site. As part of the U.S. Department of Energy’s EM-20 program, a numerical simulation capability will be added to the Subsurface Transport Over Multiple Phases (STOMP) flow simulator. The primary purpose of this document is to review the modeling approaches of foam transport in porous media. However, as an aid to understanding the simulation approaches, some experiments under unsaturated conditions and the processes of foam transport are also reviewed. Foam may be formed when the surfactant concentration is above the critical micelle concentration. There are two main types of foams – the ball foam (microfoam) and the polyhedral foam. The characteristics of bulk foam are described by the properties such as foam quality, texture, stability, density, surface tension, disjoining pressure, etc. Foam has been used to flush contaminants such as metals, organics, and nonaqueous phase liquids from unsaturated soil. Ball foam, or colloidal gas aphrons, reportedly have been used for soil flushing in contaminated site remediation and was found to be more efficient than surfactant solutions on the basis of weight of contaminant removed per gram of surfactant. Experiments also indicate that the polyhedral foam can be used to enhance soil remediation. The transport of foam in porous media is complicated in that the number of lamellae present governs flow characteristics such as viscosity, relative permeability, fluid distribution, and interactions between fluids. Hence, foam is a non-Newtonian fluid. During transport, foam destruction and formation occur. The net result of the two processes determines the foam texture (i.e., bubble density). Some of the foam may be trapped during transport. According to the impacts of the aqueous and gas flow rates, foam flow generally has two regimes – weak and strong foam. There is also a minimum pressure gradient to initiate foam flow and a critical capillary for foam to be sustained. Similar to other fluids, the transport of foam is described by Darcy’s law with the exception that the foam viscosity is variable. Three major approaches to modeling foam transport in porous media are the empirical, semi-empirical, and mechanistic methods. Mechanistic approaches can be complete in principal but may be difficult to obtain reliable parameters, whereas empirical and semi-empirical approaches can be limited by the detail used to describe foam rheology and mobility. Mechanistic approaches include the bubble population-balance model, the network/percolation theory, the catastrophe theory, and the filtration theory. Among these methods, all were developed for modeling polyhedral foam with the exception that the method based on the filtration theory was for the ball foam (microfoam).« less

beta-Endorphin-induced analgesia is inhibited by synthetic analogs of beta-endorphin.

PubMed Central

Nicolas, P; Hammonds, R G; Li, C H

1984-01-01

Competitive antagonism of human beta-endorphin (beta h-EP)-induced analgesia by synthetic beta h-EP analogs with high in vitro opiate receptor binding to in vivo analgesic potency ratio has been demonstrated. A parallel shift of the dose-response curve for analgesia to the right was observed when either beta h-EP or [ Trp27 ] -beta h-EP was coinjected with various doses of [Gln8, Gly31 ]-beta h-EP-Gly-Gly-NH2, [Arg9,19,24,28,29]-beta h-EP, or [ Cys11 ,26, Phe27 , Gly31 ]-beta h-EP. It was estimated that the most potent antagonist, [Gln8, Gly31 ]-beta h-EP-Gly-NH2, is at least 200 times more potent than naloxone. PMID:6328494

Efferent projections of the ectostriatum in the pigeon (Columba livia)

NASA Technical Reports Server (NTRS)

Husband, S. A.; Shimizu, T.

1999-01-01

The ectostriatum is a major visual component of the avian telencephalon. The core region of the ectostriatum (Ec) receives visual input from the optic tectum through thalamic nuclei. In the present study, the efferent projections of the ectostriatum were investigated by using the anterograde tracers Phaseolus vulgaris leucoagglutinin and biotinylated dextran amine. Projection patterns resulting from these tracers were confirmed by the retrograde tracer cholera toxin subunit B. When anterograde tracers were injected in Ec, primary projections were seen traveling dorsolaterally to the belt region of the ectostriatum (Ep) and the neostriatal area immediately surrounding Ep (Ep2). Neurons in Ep sent projections primarily to the overlying Ep2. The efferents of Ep2 traveled dorsolaterally to terminate in three telencephalic regions, from anterior to posterior: (1) neostriatum frontale, pars lateralis (NFL), (2) area temporo-parieto-occipitalis (TPO), and (3) neostriatum intermedium, pars lateralis (NIL). A part of the archistriatum intermedium and the lateral part of the neostriatum caudale also received somewhat minor projections. In addition, some neurons in Ec were also the source of direct, but minor, projections to the NFL, TPO, NIL, and archistriatum intermedium. The topographical relationship among the primary (Ec), secondary (Ep and Ep2), and tertiary (NFL, TPO, NIL) areas indicate that the neural populations for visual processing are organized along the rostral-caudal axis. Thus, the anterior Ec sent efferents to the anterior Ep, which in turn sent projections to anterior Ep2. Neurons in the anterior Ep2 sent projections to NFL and the anterior TPO. Similarly, the intermediate and posterior Ec sent projections to corresponding parts of Ep, whose efferents projected to intermediate and posterior Ep2, respectively. The intermediate Ep2 gave rise to major projections to TPO, whereas posterior Ep2 neurons sent efferents primarily to NIL. The organization of this neural circuit is compared with those of other sensory circuits in the avian telencephalon, as well as the laminar arrangement of the mammalian isocortex.

Gold nanoparticles and electroporation impose both separate and synergistic radiosensitizing effects in HT-29 tumor cells: an in vitro study.

PubMed

Rezaee, Zohre; Yadollahpour, Ali; Bayati, Vahid; Negad Dehbashi, Fereshteh

2017-01-01

Radiation therapy (RT) is the gold standard treatment for more than half of known tumors. Despite recent improvements in RT efficiency, the side effects of ionizing radiation (IR) in normal tissues are a dose-limiting factor that restricts higher doses in tumor treatment. One approach to enhance the efficiency of RT is the application of radiosensitizers to selectively increase the dose at the tumor site. Gold nanoparticles (GNPs) and electroporation (EP) have shown good potential as radiosensitizers for RT. This study aims to investigate the sensitizing effects of EP, GNPs, and combined GNPs-EP on the dose enhancement factor (DEF) for 6 MV photon energy. Radiosensitizing effects of EP, GNPs, and combinations of GNPs-EP were comparatively investigated in vitro for intestinal colon cancer (HT-29) and Chinese hamster ovary (CHO) cell lines by MTT assay and colony formation assay at 6 MV photon energy in six groups: IR (control group), GNPs+IR, GNPs (24 h)+IR, EP+IR, GNPs+EP+IR, and GNPs (24 h)+EP+IR. Treatment of both cell lines with EP, GNPs, and combined GNPs-EP significantly enhanced the response of cells to irradiation. However, the HT-29 showed higher DEF values for all groups. In addition, the DEF value for HT-29 cells for GNPs+IR, GNPs (24 h)+IR, EP+IR, GNPs+EP+IR, and GNPs (24 h)+EP+IR was, respectively, 1.17, 1.47, 1.36, 2.61, and 2.89, indicating synergistic radiosensitizing effect for the GNPs (24 h)+EP+IR group. Furthermore, the synergistic effect was observed just for HT-29 tumor cell lines. Combined GNPs-EP protocols induced synergistic radiosensitizing effect in HT-29 cells, and the effect is also tumor specific. This combined therapy can be beneficially used for the treatment of intrinsically less radiosensitive tumors.

Encapsulating Peritoneal Sclerosis in Peritoneal Dialysis Patients After Kidney Transplantation.

PubMed

Ayar, Y; Ersoy, A; Ocakoglu, G; Gullulu, E; Kagızmanlı, H; Yıldız, A; Oruc, A; Yavuz, M; Gullulu, M; Dilek, K

Encapsulating peritoneal sclerosis (EPS) is a serious complication for patients with chronic kidney disease (CKD) who were treated with long-term peritoneal dialysis (PD). The risk of EPS was increased after kidney transplantation. In our study we evaluated risk factors for EPS patients after kidney transplantation who were treated before with PD. In our study, between January 2008 and August 2015, 47 PD patients (12 had EPS) who underwent kidney transplantation were analyzed. Age, gender, time of PD treatment, human leukocyte antigen (HLA) matching, cold ischemia time, kidney function (serum urea, creatinine, etc), comorbidities, immunosuppressive therapy, clinical features, and outcomes of PD patients were retrospectively evaluated in both groups. Mean age was 42 (range, 25-60) years in EPS patients, versus 43 (range, 22-77) years without EPS (P = .798). Distribution of gender was similar in both groups (P = .154). The C-reactive protein levels (P < .001), number of patients with peritonitis (P = .001), length of time on PD (P < .001), and serum ferritin levels (P = .020) were higher in EPS patients. The immunosuppressive therapy was changed; tamoxifen and steroids were used after diagnosis in EPS patients. HLA matching was higher in the non-EPS group (P = .006). EPS was more often seen in patients who were treated with continuous ambulatory peritoneal dialysis (CAPD; 75%; P = .036). EPS was more often detected in cadaveric transplant recipients (83.3%; P = .024). High peritoneal transmittance rate was more identified in EPS (+) patients (P = .001). EPS was more often seen in patients who were treated with icodextrin-based regimens in PD before transplantation (91.7%; P = .037). The length of time on PD and high ferritin levels increased EPS 1.08 and 1.01, respectively (P = .036 and .049, respectively), in multivariate analysis. The length of time on PD, type of PD, PD regimens with icodextrin, episodes of peritonitis, and peritoneal transmittance in patients with CKD affect the development of EPS after transplantation. Copyright © 2017 Elsevier Inc. All rights reserved.

Pharmacokinetics of erythropoietin in intact and anephric dogs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fu, J.S.; Lertora, J.J.; Brookins, J.

1988-06-01

The present studies were performed to determine the pharmacokinetic parameters of erythropoietin in intact and anephric dogs by use of unlabeled crude native erythropoietin (nEp) and iodine 125-labeled purified recombinant erythropoietin (rEp) given by intravenous infusion for 15 minutes. Sephadex G-75 gel filtration was used to confirm that the 125I-rEp molecule remained iodinated in dog plasma during the 24-hour period of these studies. The plasma disappearance of erythropoietin conformed to a biexponential equation for both nEp and 125I-rEp, with the central compartment being larger than the peripheral compartment. The mean distribution half-life of 75.3 +/- 21.2 minutes for nEp wasmore » significantly (p less than 0.05) longer than that of 125I-rEp (23.7 +/- 5.0 minutes) in intact dogs. The intercompartmental clearance (CIic) for nEp (0.018 +/- 0.006 L/kg/hr) was significantly smaller than that of 125I-rEp (0.068 +/- 0.018 L/kg/hr) in intact dogs (p less than 0.05). There were no significant differences in apparent volume of distribution, elimination half-life, and elimination clearance (CIe) for nEp and rEp in intact dogs. The mean elimination half-life for 125I-rEp in intact dogs (9.0 +/- 0.6 hours) and anephric dogs (13.8 +/- 1.4 hours) was significantly different (p less than 0.05). The CIe for 125I-rEp in anephric dogs (0.008 +/- 0.001 L/kg/hr) was significantly (p less than 0.05) smaller than that of 125I-rEp in intact dogs (0.011 +/- 0.001 L/kg/hr). There were no significant differences in apparent volume of distribution, distribution half-life, and CIic for 125I-rEp in intact and anephric dogs.« less

A deletion mutation at the ep locus causes low seed coat peroxidase activity in soybean.

PubMed

Gijzen, M

1997-11-01

The Ep locus severely affects the amount of peroxidase enzyme in soybean seed coats. Plants containing the dominant Ep allele accumulate large amounts of peroxidase in the hourglass cells of the sub-epidermis. Homozygous recessive epep genotypes do not accumulate peroxidase in the hourglass cells and are much reduced in total seed coat peroxidase activity. To isolate the gene encoding the seed coat peroxidase and to determine whether it corresponds to the Ep locus, a cDNA library was constructed from developing seed coats and an abundant 1.3 kb peroxidase transcript was cloned. The corresponding structural gene was also isolated from a genomic library. Sequence analysis shows that the seed coat peroxidase is translated as a 352 amino acid precursor protein of 38 kDa. Processing of a putative 26 amino acid signal sequence results in a mature protein of 326 residues with a calculated mass of 35 kDa and a pl of 4.4. Using probes derived from the cDNA, genomic DNA blot hybridization and polymerase chain reaction analysis detected polymorphisms that distinguished EpEp and epep genotypes. Co-segregation of the polymorphisms in an F2 population from a cross of EpEp and epep plants shows that the Ep locus encodes the seed coat peroxidase protein. Comparison of Ep and ep alleles indicates that the recessive gene lacks 87 bp of sequence encompassing the translation start codon. Analysis by RNA blot hybridization shows that epep plants have drastically reduced amounts of peroxidase transcript compared with EpEp plants. The peroxidase mRNA is abundant in seed coat tissues of EpEp plants during the late stages of seed maturation, and could also be detected in root tissues, but not in the flower, embryo, pod or leaf. The results indicate that the lack of peroxidase accumulation in seed coats of homozygous recessive epep plants is due to a mutation of the structural gene that reduces transcript abundance.

Unilateral Salpingectomy and Methotrexate Are Associated With a Similar Recurrence Rate of Ectopic Pregnancy in Patients Undergoing In Vitro Fertilization.

PubMed

Irani, Mohamad; Robles, Alex; Gunnala, Vinay; Spandorfer, Steven D

To determine whether different treatment approaches of ectopic pregnancy (EP), particularly unilateral salpingectomy and methotrexate, affect its recurrence rate in patients undergoing in vitro fertilization (IVF). A retrospective cohort study (Canadian Task Force classification II-2). An academic medical center. Patients with a history of a previous EP who achieved pregnancy after IVF cycles between January 2004 and August 2015 were included. The recurrence rate of EP was compared between patients who underwent different treatment approaches for a previous EP. IVF. A total of 594 patients were included. Seventeen patients had a recurrence of EP (2.9%). Patients with a history of ≥2 EPs were associated with a significantly higher recurrence rate of EP than those with 1 previous EP (8.5% vs. 1.8%; p = .01; odds ratio [OR] = 2.2; 95% confidence interval [CI], 1.2-4.4). Patients who underwent unilateral salpingectomy (n = 245) had a comparable recurrence rate of EP after IVF with those who received methotrexate (n = 283) (3.6% vs. 2.8%; p = .5; OR = 1.3; 95% CI, 0.4-3.4). This OR remained unchanged after adjusting for patient's age, number of previous EPs, number of transferred embryos, and peak estradiol level during stimulation (adjusted OR = 1.4; 95% CI, 0.5-3.8). None of the patients who underwent bilateral salpingectomy (n = 45) or salpingostomy (n = 21) had a recurrence of EP after IVF. The recurrence rate of EP significantly correlates with the number of previous EPs. Treatment of EP with methotrexate has a comparable recurrence rate of EP after IVF with unilateral salpingectomy. Therefore, the risk of recurrence should not be a reason to favor salpingectomy over methotrexate in this population. Copyright © 2017 AAGL. Published by Elsevier Inc. All rights reserved.

Advanced nondestructive techniques applied for the detection of discontinuities in aluminum foams

NASA Astrophysics Data System (ADS)

Katchadjian, Pablo; García, Alejandro; Brizuela, Jose; Camacho, Jorge; Chiné, Bruno; Mussi, Valerio; Britto, Ivan

2018-04-01

Metal foams are finding an increasing range of applications by their lightweight structure and physical, chemical and mechanical properties. Foams can be used to fill closed moulds for manufacturing structural foam parts of complex shape [1]; foam filled structures are expected to provide good mechanical properties and energy absorption capabilities. The complexity of the foaming process and the number of parameters to simultaneously control, demand a preliminary and hugely wide experimental activity to manufacture foamed components with a good quality. That is why there are many efforts to improve the structure of foams, in order to obtain a product with good properties. The problem is that even for seemingly identical foaming conditions, the effective foaming can vary significantly from one foaming trial to another. The variation of the foams often is related by structural imperfections, joining region (foam-foam or foam-wall mold) or difficulties in achieving a complete filling of the mould. That is, in a closed mold, the result of the mold filling and its structure or defects are not known a priori and can eventually vary significantly. These defects can cause a drastic deterioration of the mechanical properties [2] and lead to a low performance in its application. This work proposes the use of advanced nondestructive techniques for evaluating the foam distribution after filling the mold to improve the manufacturing process. To achieved this purpose ultrasonic technique (UT) and cone beam computed tomography (CT) were applied on plate and structures of different thicknesses filled with foam of different porosity. UT was carried out on transmission mode with low frequency air-coupled transducers [3], in focused and unfocused configurations.

Analysis of Influence of Foaming Mixture Components on Structure and Properties of Foam Glass

NASA Astrophysics Data System (ADS)

Karandashova, N. S.; Goltsman, B. M.; Yatsenko, E. A.

2017-11-01

It is recommended to use high-quality thermal insulation materials to increase the energy efficiency of buildings. One of the best thermal insulation materials is foam glass - durable, porous material that is resistant to almost any effect of substance. Glass foaming is a complex process depending on the foaming mode and the initial mixture composition. This paper discusses the influence of all components of the mixture - glass powder, foaming agent, enveloping material and water - on the foam glass structure. It was determined that glass powder is the basis of the future material. A foaming agent forms a gas phase in the process of thermal decomposition. This aforementioned gas foams the viscous glass mass. The unreacted residue thus changes a colour of the material. The enveloping agent slows the foaming agent decomposition preventing its premature burning out and, in addition, helps to accelerate the sintering of glass particles. The introduction of water reduces the viscosity of the foaming mixture making it evenly distributed and also promotes the formation of water gas that additionally foams the glass mass. The optimal composition for producing the foam glass with the density of 150 kg/m3 is defined according to the results of the research.

Foams for barriers and nonlethal weapons

NASA Astrophysics Data System (ADS)

Rand, Peter B.

1997-01-01

Our times demand better solutions to conflict resolution than simply shooting someone. Because of this, police and military interest in non-lethal concepts is high. Already in use are pepper sprays, bean-bag guns, flash-bang grenades, and rubber bullets. At Sandia we got a head start on non- lethal weapon concepts. Protection of nuclear materials required systems that went way beyond the traditional back vault. Dispensable deterrents were used to allow a graduated response to a threat. Sticky foams and stabilized aqueous foams were developed to provide access delay. Foams won out for security systems simply because you could get a large volume from a small container. For polymeric foams the expansion ratio is thirty to fifty to one. In aqueous foams expansion ratios of one thousand to ne are easily obtained. Recent development work on sticky foams has included a changeover to environmentally friendly solvents, foams with very low toxicity, and the development of non-flammable silicone resin based foams. High expansion aqueous foams are useful visual and aural obscurants. Our recent aqueous foam development has concentrated on using very low toxicity foaming agents combined with oleoresin capsicum irritant to provide a safe but highly irritating foam.

An EP2 Agonist Facilitates NMDA-Induced Outward Currents and Inhibits Dendritic Beading through Activation of BK Channels in Mouse Cortical Neurons

PubMed Central

Hayashi, Yoshinori; Morinaga, Saori; Liu, Xia; Zhang, Jing; Wu, Zhou; Yokoyama, Takeshi; Nakanishi, Hiroshi

2016-01-01

Prostaglandin E2 (PGE2), a major metabolite of arachidonic acid produced by cyclooxygenase pathways, exerts its bioactive responses by activating four E-prostanoid receptor subtypes, EP1, EP2, EP3, and EP4. PGE2 enables modulating N-methyl-D-aspartate (NMDA) receptor-mediated responses. However, the effect of E-prostanoid receptor agonists on large-conductance Ca2+-activated K+ (BK) channels, which are functionally coupled with NMDA receptors, remains unclear. Here, we showed that EP2 receptor-mediated signaling pathways increased NMDA-induced outward currents (I NMDA-OUT), which are associated with the BK channel activation. Patch-clamp recordings from the acutely dissociated mouse cortical neurons revealed that an EP2 receptor agonist activated I NMDA-OUT, whereas an EP3 receptor agonist reduced it. Agonists of EP1 or EP4 receptors showed no significant effects on I NMDA-OUT. A direct perfusion of 3,5′-cyclic adenosine monophosphate (cAMP) through the patch pipette facilitated I NMDA-OUT, which was abolished by the presence of protein kinase A (PKA) inhibitor. Furthermore, facilitation of I NMDA-OUT caused by an EP2 receptor agonist was significantly suppressed by PKA inhibitor. Finally, the activation of BK channels through EP2 receptors facilitated the recovery phase of NMDA-induced dendritic beading in the primary cultured cortical neurons. These results suggest that a direct activation of BK channels by EP2 receptor-mediated signaling pathways plays neuroprotective roles in cortical neurons. PMID:27298516