Liquid crystals for organic thin-film transistors

NASA Astrophysics Data System (ADS)

Iino, Hiroaki; Usui, Takayuki; Hanna, Jun-Ichi

2015-04-01

Crystalline thin films of organic semiconductors are a good candidate for field effect transistor (FET) materials in printed electronics. However, there are currently two main problems, which are associated with inhomogeneity and poor thermal durability of these films. Here we report that liquid crystalline materials exhibiting a highly ordered liquid crystal phase of smectic E (SmE) can solve both these problems. We design a SmE liquid crystalline material, 2-decyl-7-phenyl-[1]benzothieno[3,2-b][1]benzothiophene (Ph-BTBT-10), for FETs and synthesize it. This material provides uniform and molecularly flat polycrystalline thin films reproducibly when SmE precursor thin films are crystallized, and also exhibits high durability of films up to 200 °C. In addition, the mobility of FETs is dramatically enhanced by about one order of magnitude (over 10 cm2 V-1 s-1) after thermal annealing at 120 °C in bottom-gate-bottom-contact FETs. We anticipate the use of SmE liquid crystals in solution-processed FETs may help overcome upcoming difficulties with novel technologies for printed electronics.

Raman spectrum of natural and synthetic stishovite

USGS Publications Warehouse

Hemley, R.J.; Mao, Ho-kwang; Chao, E.C.T.

1986-01-01

Raman spectra of natural and synthetic samples of stishovite have been measured with a micro-optical spectrometer system. These spectra have a pattern that is characteristic of rutile-structured oxides. The spectrum of synthetic stishovite is characterized by well-resolved bands at 231, 589, 753, and 967 cm-1, which are assigned as the B1g, Eg, A1g, and B2g fundamentals, respectively, of the first-order Raman spectrum of the ideal, ordered structure. Natural stishovite obtained from Meteor Crater, Arizona has a first-order Raman spectrum that is fully consistent with that of the synthetic material. The observed spectrum of the natural sample, however, is weaker and has bands in addition to those identified as fundamentals in the spectrum of the synthetic material. A broad band at ???475 cm-1 may be indicative of glass or contaminants derived from the extraction procedure. Alternatively, this band may arise from multiphonon scattering that is enhanced by poor crystallinity or structural disorder in the natural shocked sample. ?? 1986 Springer-Verlag.

Dynamics of Granular Materials

NASA Technical Reports Server (NTRS)

Behringer, Robert P.

1996-01-01

Granular materials exhibit a rich variety of dynamical behavior, much of which is poorly understood. Fractal-like stress chains, convection, a variety of wave dynamics, including waves which resemble capillary waves, l/f noise, and fractional Brownian motion provide examples. Work beginning at Duke will focus on gravity driven convection, mixing and gravitational collapse. Although granular materials consist of collections of interacting particles, there are important differences between the dynamics of a collections of grains and the dynamics of a collections of molecules. In particular, the ergodic hypothesis is generally invalid for granular materials, so that ordinary statistical physics does not apply. In the absence of a steady energy input, granular materials undergo a rapid collapse which is strongly influenced by the presence of gravity. Fluctuations on laboratory scales in such quantities as the stress can be very large-as much as an order of magnitude greater than the mean.

Intermediate honeycomb ordering to trigger oxygen redox chemistry in layered battery electrode

PubMed Central

Mortemard de Boisse, Benoit; Liu, Guandong; Ma, Jiangtao; Nishimura, Shin-ichi; Chung, Sai-Cheong; Kiuchi, Hisao; Harada, Yoshihisa; Kikkawa, Jun; Kobayashi, Yoshio; Okubo, Masashi; Yamada, Atsuo

2016-01-01

Sodium-ion batteries are attractive energy storage media owing to the abundance of sodium, but the low capacities of available cathode materials make them impractical. Sodium-excess metal oxides Na2MO3 (M: transition metal) are appealing cathode materials that may realize large capacities through additional oxygen redox reaction. However, the general strategies for enhancing the capacity of Na2MO3 are poorly established. Here using two polymorphs of Na2RuO3, we demonstrate the critical role of honeycomb-type cation ordering in Na2MO3. Ordered Na2RuO3 with honeycomb-ordered [Na1/3Ru2/3]O2 slabs delivers a capacity of 180 mAh g−1 (1.3-electron reaction), whereas disordered Na2RuO3 only delivers 135 mAh g−1 (1.0-electron reaction). We clarify that the large extra capacity of ordered Na2RuO3 is enabled by a spontaneously ordered intermediate Na1RuO3 phase with ilmenite O1 structure, which induces frontier orbital reorganization to trigger the oxygen redox reaction, unveiling a general requisite for the stable oxygen redox reaction in high-capacity Na2MO3 cathodes. PMID:27088834

Compaction behavior of out-of-autoclave prepreg materials

NASA Astrophysics Data System (ADS)

Serrano, Léonard; Olivier, Philippe; Cinquin, Jacques

2017-10-01

The main challenges with composite parts manufacturing are related to the curing means, mainly autoclaves, the length of their cycles and their operating costs. In order to decrease this dependency, out of autoclave materials have been considered as a solution for high production rate parts such as spars, flaps, etc… However, most out-of-autoclave process do not possess the same maturity as their counterpart, especially concerning part quality1. Some pre-cure processes such as compaction and ply lay-up are usually less of a concern for autoclave manufacturing: the pressure applied during the cycle participates to reduce the potential defects (porosity caused by a poor quality lay-up, bad compaction, entrapped air or humidity…). For out-of-autoclave parts, those are crucial steps which may have many consequences on the final quality of the laminate2. In order to avoid this quality loss, those steps must be well understood.

Crossmodal association of auditory and visual material properties in infants.

PubMed

Ujiie, Yuta; Yamashita, Wakayo; Fujisaki, Waka; Kanazawa, So; Yamaguchi, Masami K

2018-06-18

The human perceptual system enables us to extract visual properties of an object's material from auditory information. In monkeys, the neural basis underlying such multisensory association develops through experience of exposure to a material; material information could be processed in the posterior inferior temporal cortex, progressively from the high-order visual areas. In humans, however, the development of this neural representation remains poorly understood. Here, we demonstrated for the first time the presence of a mapping of the auditory material property with visual material ("Metal" and "Wood") in the right temporal region in preverbal 4- to 8-month-old infants, using near-infrared spectroscopy (NIRS). Furthermore, we found that infants acquired the audio-visual mapping for a property of the "Metal" material later than for the "Wood" material, since infants form the visual property of "Metal" material after approximately 6 months of age. These findings indicate that multisensory processing of material information induces the activation of brain areas related to sound symbolism. Our findings also indicate that the material's familiarity might facilitate the development of multisensory processing during the first year of life.

Prototypical Organic–Oxide Interface: Intramolecular Resolution of Sexiphenyl on In 2O 3 (111)

DOE PAGES

Wagner, Margareta; Hofinger, Jakob; Setvin, Martin; ...

2018-03-28

The performance of an organic semiconductor device is critically determined by the geometric alignment, orientation, and ordering of the organic molecules. Although an organic multilayer eventually adopts the crystal structure of the organic material, the alignment and configuration at the interface with the substrate/electrode material are essential for charge injection into the organic layer. This work focuses on the prototypical organic semiconductor para-sexiphenyl (6P) adsorbed on In 2O 3(111), the thermodynamically most stable surface of the material that the most common transparent conducting oxide, indium tin oxide, is based on. The onset of nucleation and formation of the first monolayermore » are followed with atomically resolved scanning tunneling microscopy and noncontact atomic force microscopy (nc-AFM). Annealing to 200 °C provides sufficient thermal energy for the molecules to orient themselves along the high-symmetry directions of the surface, leading to a single adsorption site. The AFM data suggests an essentially planar adsorption geometry. With increasing coverage, the 6P molecules first form a loose network with a poor long-range order. Eventually, the molecules reorient into an ordered monolayer. In conclusion, this first monolayer has a densely packed, well-ordered (2 × 1) structure with one 6P per In 2O 3(111) substrate unit cell, that is, a molecular density of 5.64 × 10 13 cm –2.« less

Prototypical Organic–Oxide Interface: Intramolecular Resolution of Sexiphenyl on In 2O 3 (111)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagner, Margareta; Hofinger, Jakob; Setvin, Martin

The performance of an organic semiconductor device is critically determined by the geometric alignment, orientation, and ordering of the organic molecules. Although an organic multilayer eventually adopts the crystal structure of the organic material, the alignment and configuration at the interface with the substrate/electrode material are essential for charge injection into the organic layer. This work focuses on the prototypical organic semiconductor para-sexiphenyl (6P) adsorbed on In 2O 3(111), the thermodynamically most stable surface of the material that the most common transparent conducting oxide, indium tin oxide, is based on. The onset of nucleation and formation of the first monolayermore » are followed with atomically resolved scanning tunneling microscopy and noncontact atomic force microscopy (nc-AFM). Annealing to 200 °C provides sufficient thermal energy for the molecules to orient themselves along the high-symmetry directions of the surface, leading to a single adsorption site. The AFM data suggests an essentially planar adsorption geometry. With increasing coverage, the 6P molecules first form a loose network with a poor long-range order. Eventually, the molecules reorient into an ordered monolayer. In conclusion, this first monolayer has a densely packed, well-ordered (2 × 1) structure with one 6P per In 2O 3(111) substrate unit cell, that is, a molecular density of 5.64 × 10 13 cm –2.« less

The artists' materials of Fernando Melani: A precursor of the Poor Art artistic movement in Italy

NASA Astrophysics Data System (ADS)

Carlesi, Serena; Bartolozzi, Giovanni; Cucci, Costanza; Marchiafava, Veronica; Picollo, Marcello

2013-03-01

A comprehensive understanding of both the chemical composition and physical behaviour of modern materials is an important consideration in devising correct conservation treatments for contemporary artworks. To this end, national and international research projects and networks have been established that deal mainly with the preservation, conservation, and understanding of materials used by contemporary artists. This paper focuses on the self-taught artist Fernando Melani (1907-1985), one of the precursors of the Poor Art artistic movement in Italy, and for the first time provides a scientific viewpoint on the artist's materials and works. The analyses, which mainly focus on the pigments/dyes found in his home-studio, were carried out primarily by using Fourier Transform Infrared Spectroscopy (FT-IR) and ultraviolet, visible, and near-infrared Fibre Optic Reflectance Spectroscopy (UV-Vis-NIR FORS). This paper emphasises the performance of FT-IR and FORS in the identification of contemporary artistic materials, since these two techniques have been found to produce highly complementary data. The use of both of these was required in order to obtain a comprehensive understanding of the composition of Melani's materials. Furthermore, one of his artworks, named by Melani himself with its inventory number N. Inv. 2625 (1981), was investigated in situ with the sole use of the FORS technique. The results showed that Melani used traditional inorganic pigments as well as modern organic dyes. Calcite and barite were used as fillers and extenders. Sulphur and abrasive powder were also found, thus confirming his use of a large variety of non-conventional artists' materials.

The Chemical Abundances of New Extremely Metal-Poor Giants with [Fe/H] < -3.0

NASA Astrophysics Data System (ADS)

Rhee, Jaehyon; Fink, M.; Rhee, W.

2012-01-01

Extremely metal-poor (EMP) stars with [Fe/H] < -3.0 observable in the Galactic halo and thick disk today are believed to be the second-generation stars born out of those materials that were slightly chemically polluted by the extinct, metal-free first stars. If true, these oldest surviving stars with the lowest metal abundances are astrophysical laboratories that may shed essential light on the origins and evolution of the chemical elements and on the formation of the Milky Way. In order to newly discover field metal-deficient stars in the inner halo of the Galaxy, the Purdue Ultra Metal-Poor Star Survey (PUMPSS) program was conducted. Candidate metal-poor stars were initially selected utilizing the photometric data of the GALEX and the 2MASS, and subsequent medium- and high-resolution spectroscopy were carried out for the identification of true metal-poor giant stars and detailed chemical abundance analyses, respectively. We present an overview of the PUMPSS program and the results of the abundance analysis for high-dispersion spectra of EMP giant stars taken at the KPNO 4m telescope. We acknowledge support for this work from NASA grants 07-ADP07-0080 and 05-GALEX05-27.

New Oxide Ceramic Developed for Superior High-Temperature Wear Resistance

NASA Technical Reports Server (NTRS)

Sayir, Ali; Miyoshi, Kazuhisa; Farmer, Serene C.

2003-01-01

Ceramics, for the most part, do not have inherently good tribological properties. For example friction coefficients in excess of 0.7 have been reported for silicon nitride sliding on silicon nitride or on bearing steel (ref. 1). High friction is always accompanied by considerable wear. Despite their inherently poor tribological properties, the high strength and high toughness of silicon nitride (Si3N4) ceramics has led to their successful use in tribological applications (refs. 1 to 4). The upper temperature limit for the application of Si3N4 as wear-resistant material is limited by reaction with the tribological environment (ref. 3). Silicon nitride is known to produce a thin silicon dioxide film with easy shear capability that results in low friction and low wear in a moist environment (ref. 5). At elevated temperatures, the removal of the reaction product that acts as lubricant causes the friction coefficient to increase and, consequently, the wear performance to become poor. New materials are sought that will have wear resistance superior to that of Si3N4 at elevated temperatures and in harsh environments. A new class of oxide ceramic materials has been developed with potential for excellent high-temperature wear resistance. The new material consists of a multicomponent oxide with a two-phase microstructure, in which the wear resistance of the mixed oxide is significantly higher than that of the individual constituents. This is attributed to the strong constraining effects provided by the interlocking microstructures at different length scales, to the large aspect ratio of the phases, to the strong interphase bonding, and to the residual stresses. Fretting wear tests were conducted by rubbing the new ceramic material against boron carbide (B4C). The new ceramic material produced a wear track groove on B4C, suggesting significantly higher wear resistance for the oxide ceramic. The new material did not suffer from any microstructural degradation after the wear test. The wear rate of the new ceramic material at 600 C was determined to be on the order of 10-10 mm3/N-m, which is 3 to 5 orders of magnitude lower than that for the current state-of-theart wear-resistant materials (Si3N4and B4C). The friction coefficient of the new ceramic materials is on the order of 0.4, which is significantly lower than that of silicon nitride. This new class of oxide materials has shown considerable potential for applications requiring high wear resistance at high temperatures and in harsh environments. New understanding of the wear behavior of ceramic materials is emerging as a result of the surprisingly high wear resistance of two-phase oxide ceramics. There is excellent potential for further improvements in the wear resistance of oxide ceramics through optimizing the microstructure and altering the crystallographic properties of specific oxide materials as a second phase to reduce the coefficient of friction at elevated temperatures.

The mystery of a supposed massive star exploding in a brightest cluster galaxy

NASA Astrophysics Data System (ADS)

Hosseinzadeh, Griffin

2017-08-01

Most of the diversity of core-collapse supernovae results from late-stage mass loss by their progenitor stars. Supernovae that interact with circumstellar material (CSM) are a particularly good probe of these last stages of stellar evolution. Type Ibn supernovae are a rare and poorly understood class of hydrogen-poor explosions that show signs of interaction with helium-rich CSM. The leading hypothesis is that they are explosions of very massive Wolf-Rayet stars in which the supernova ejecta excites material previously lost by stellar winds. These massive stars have very short lifetimes, and therefore should only found in actively star-forming galaxies. However, PS1-12sk is a Type Ibn supernova found on the outskirts of a giant elliptical galaxy. As this is extraordinary unlikely, we propose to obtain deep UV images of the host environment of PS1-12sk in order to map nearby star formation and/or find a potential unseen star-forming host. If star formation is detected, its amount and location will provide deep insights into the progenitor picture for the poorly-understood Type Ibn class. If star formation is still not detected, these observations would challenge the well-accepted hypothesis that these are core-collapse supernovae at all.

Porous Biodegradable Metals for Hard Tissue Scaffolds: A Review

PubMed Central

Yusop, A. H.; Bakir, A. A.; Shaharom, N. A.; Abdul Kadir, M. R.; Hermawan, H.

2012-01-01

Scaffolds have been utilized in tissue regeneration to facilitate the formation and maturation of new tissues or organs where a balance between temporary mechanical support and mass transport (degradation and cell growth) is ideally achieved. Polymers have been widely chosen as tissue scaffolding material having a good combination of biodegradability, biocompatibility, and porous structure. Metals that can degrade in physiological environment, namely, biodegradable metals, are proposed as potential materials for hard tissue scaffolding where biodegradable polymers are often considered as having poor mechanical properties. Biodegradable metal scaffolds have showed interesting mechanical property that was close to that of human bone with tailored degradation behaviour. The current promising fabrication technique for making scaffolds, such as computation-aided solid free-form method, can be easily applied to metals. With further optimization in topologically ordered porosity design exploiting material property and fabrication technique, porous biodegradable metals could be the potential materials for making hard tissue scaffolds. PMID:22919393

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perras, Frederic A.; Wang, Lin-Lin; Manzano, J. Sebastian

The efficacy of dynamic nuclear polarization (DNP) surface-enhanced NMR spectroscopy (SENS) is reviewed for alumina, silica, and ordered mesoporous carbon (OMC) materials, with vastly different surface areas, as a function of the biradical concentration. Importantly, our studies show that the use of a “one-size-fits-all” biradical concentration should be avoided when performing DNP SENS experiments and instead an optimal concentration should be selected as appropriate for the type of material studied as well as its surface area. In general, materials with greater surface areas require higher radical concentrations for best possible DNP performance. This result is explained with the use ofmore » a thermodynamic model wherein radical-surface interactions are expected to lead to an increase in the local concentration of the polarizing agent at the surface. We also show, using plane-wave density functional theory calculations, that weak radical-surface interactions are the cause of the poor performance of DNP SENS for carbonaceous materials.« less

Surface Exposure Ages of Space-Weathered Grains from Asteroid 25143 Itokawa

NASA Technical Reports Server (NTRS)

Keller, L. P.; Berger, E. L.; Christoffersen, R.

2015-01-01

Space weathering processes such as solar wind ion irradiation and micrometeorite impacts are widely known to alter the properties of regolith materials exposed on airless bodies. The rates of space weathering processes however, are poorly constrained for asteroid regoliths, with recent estimates ranging over many orders of magnitude. The return of surface samples by JAXA's Hayabusa mission to asteroid 25143 Itokawa, and their laboratory analysis provides "ground truth" to anchor the timescales for space weathering processes on airless bodies.

Cyclic Creep and Recovery Behavior of Nextel(Trademark) 720/Alumina Ceramic Matrix Composite at 1200deg C in Air and in Steam Environments

DTIC Science & Technology

2007-09-01

steam. The creep and recovery periods ranged from 3 min to 30 h. The laboratory air tests significantly exceeded the life of the monotonic creep ...orders of magnitude improvement in the creep life and rate. The presence of steam greatly reduced the performance of the material. The results in...steam. Mehrman also reported that prior fatigue subsequently improved in air but creep performance but in steam creep performance remained poor

Surface modified CF x cathode material for ultrafast discharge and high energy density

DOE PAGES

Dai, Yang; Zhu, Yimei; Cai, Sendan; ...

2014-11-10

Li/CF x primary possesses the highest energy density of 2180 W h kg⁻¹ among all primary lithium batteries. However, a key limitation for the utility of this type of battery is in its poor rate capability because the cathode material, CF x, is an intrinsically poor electronic conductor. Here, we report on our development of a controlled process of surface de-fluorination under mild hydrothermal conditions to modify the highly fluorinated CF x. The modified CF x, consisting of an in situ generated shell component of F-graphene layers, possesses good electronic conductivity and removes the transporting barrier for lithium ions, yieldingmore » a high-capacity performance and an excellent rate-capability. Indeed, a capacity of 500 mA h g⁻¹ and a maximum power density of 44 800 W kg⁻¹ can be realized at the ultrafast rate of 30 C (24 A g⁻¹), which is over one order of magnitude higher than that of the state-of-the-art primary lithium-ion batteries.« less

Manufacturing Energy Intensity and Opportunity Analysis for Fiber-Reinforced Polymer Composites and Other Lightweight Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liddell, Heather; Brueske, Sabine; Carpenter, Alberta

With their high strength-to-weight ratios, fiber-reinforced polymer (FRP) composites are important materials for lightweighting in structural applications; however, manufacturing challenges such as low process throughput and poor quality control can lead to high costs and variable performance, limiting their use in commercial applications. One of the most significant challenges for advanced composite materials is their high manufacturing energy intensity. This study explored the energy intensities of two lightweight FRP composite materials (glass- and carbon-fiber-reinforced polymers), with three lightweight metals (aluminum, magnesium, and titanium) and structural steel (as a reference material) included for comparison. Energy consumption for current typical and state-of-the-artmore » manufacturing processes were estimated for each material, deconstructing manufacturing process energy use by sub-process and manufacturing pathway in order to better understand the most energy intensive steps. Energy saving opportunities were identified and quantified for each production step based on a review of applied R&D technologies currently under development in order to estimate the practical minimum energy intensity. Results demonstrate that while carbon fiber reinforced polymer (CFRP) composites have the highest current manufacturing energy intensity of all materials considered, the large differences between current typical and state-of-the-art energy intensity levels (the 'current opportunity') and between state-of-the-art and practical minimum energy intensity levels (the 'R&D opportunity') suggest that large-scale energy savings are within reach.« less

Mesocrystalline calcium silicate hydrate: A bioinspired route toward elastic concrete materials

PubMed Central

Picker, Andreas; Nicoleau, Luc; Burghard, Zaklina; Bill, Joachim; Zlotnikov, Igor; Labbez, Christophe; Nonat, André; Cölfen, Helmut

2017-01-01

Calcium silicate hydrate (C-S-H) is the binder in concrete, the most used synthetic material in the world. The main weakness of concrete is the lack of elasticity and poor flexural strength considerably limiting its potential, making reinforcing steel constructions necessary. Although the properties of C-S-H could be significantly improved in organic hybrids, the full potential of this approach could not be reached because of the random C-S-H nanoplatelet structure. Taking inspiration from a sea urchin spine with highly ordered nanoparticles in the biomineral mesocrystal, we report a bioinspired route toward a C-S-H mesocrystal with highly aligned C-S-H nanoplatelets interspaced with a polymeric binder. A material with a bending strength similar to nacre is obtained, outperforming all C-S-H–based materials known to date. This strategy could greatly benefit future construction processes because fracture toughness and elasticity of brittle cementitious materials can be largely enhanced on the nanoscale. PMID:29209660

The artists' materials of Fernando Melani: a precursor of the Poor Art artistic movement in Italy.

PubMed

Carlesi, Serena; Bartolozzi, Giovanni; Cucci, Costanza; Marchiafava, Veronica; Picollo, Marcello

2013-03-01

A comprehensive understanding of both the chemical composition and physical behaviour of modern materials is an important consideration in devising correct conservation treatments for contemporary artworks. To this end, national and international research projects and networks have been established that deal mainly with the preservation, conservation, and understanding of materials used by contemporary artists. This paper focuses on the self-taught artist Fernando Melani (1907-1985), one of the precursors of the Poor Art artistic movement in Italy, and for the first time provides a scientific viewpoint on the artist's materials and works. The analyses, which mainly focus on the pigments/dyes found in his home-studio, were carried out primarily by using Fourier Transform Infrared Spectroscopy (FT-IR) and ultraviolet, visible, and near-infrared Fibre Optic Reflectance Spectroscopy (UV-Vis-NIR FORS). This paper emphasises the performance of FT-IR and FORS in the identification of contemporary artistic materials, since these two techniques have been found to produce highly complementary data. The use of both of these was required in order to obtain a comprehensive understanding of the composition of Melani's materials. Furthermore, one of his artworks, named by Melani himself with its inventory number N. Inv. 2625 (1981), was investigated in situ with the sole use of the FORS technique. The results showed that Melani used traditional inorganic pigments as well as modern organic dyes. Calcite and barite were used as fillers and extenders. Sulphur and abrasive powder were also found, thus confirming his use of a large variety of non-conventional artists' materials. Copyright © 2012 Elsevier B.V. All rights reserved.

Infrared Micro-Spectroscopy of Organic and Hydrous Components in Some Antarctic Micrometeorites

NASA Technical Reports Server (NTRS)

Suzuki, A.; Kebukawa, Y.; Nakashima, S.; Keller, L. P.; Zolensky, M. E.; Nakamura, T.

2005-01-01

Micrometeorites extracted from Antarctic ice are a major source of extraterrestrial materials available for study in the laboratory. Materials in this size range are important because the peak in the mass flux distribution of extraterrestrial particles accreted by the Earth occurs for particles approximately 200 microns in diameter with a mass accretion rate estimated at approximately 40 x 10(exp 6) kilograms per year. It has been suggested that micrometeorites may have contributed much pre-biotic organic matter to the early Earth, but the types and abundances of organic material in micrometeorites are poorly known. We have conducted infrared (IR) micro-spectrocopy of small micrometeorites (about 100 microns in size) in order to characterize organic matter that is present in the particles. The obtained results were compared with IR signatures of representative carbonaceous chondrites.

Design of crystal-like aperiodic solids with selective disorder–phonon coupling

PubMed Central

Overy, Alistair R.; Cairns, Andrew B.; Cliffe, Matthew J.; Simonov, Arkadiy; Tucker, Matthew G.; Goodwin, Andrew L.

2016-01-01

Functional materials design normally focuses on structurally ordered systems because disorder is considered detrimental to many functional properties. Here we challenge this paradigm by showing that particular types of strongly correlated disorder can give rise to useful characteristics that are inaccessible to ordered states. A judicious combination of low-symmetry building unit and high-symmetry topological template leads to aperiodic ‘procrystalline' solids that harbour this type of disorder. We identify key classes of procrystalline states together with their characteristic diffraction behaviour, and establish mappings onto known and target materials. The strongly correlated disorder found in these systems is associated with specific sets of modulation periodicities distributed throughout the Brillouin zone. Lattice dynamical calculations reveal selective disorder-driven phonon broadening that resembles the poorly understood ‘waterfall' effect observed in relaxor ferroelectrics. This property of procrystalline solids suggests a mechanism by which strongly correlated topological disorder might allow independently optimized thermal and electronic transport behaviour, such as required for high-performance thermoelectrics. PMID:26842772

Simulation studies of nucleation of ferroelectric polarization reversal.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brennecka, Geoffrey L.; Winchester, Benjamin Michael

2014-08-01

Electric field-induced reversal of spontaneous polarization is the defining characteristic of a ferroelectric material, but the process(es) and mechanism(s) associated with the initial nucleation of reverse-polarity domains are poorly understood. This report describes studies carried out using phase field modeling of LiTaO 3, a relatively simple prototype ferroelectric material, in order to explore the effects of either mechanical deformation or optically-induced free charges on nucleation and resulting domain configuration during field-induced polarization reversal. Conditions were selected to approximate as closely as feasible those of accompanying experimental work in order to provide not only support for the experimental work but alsomore » ensure that additional experimental validation of the simulations could be carried out in the future. Phase field simulations strongly support surface mechanical damage/deformation as effective for dramatically reducing the overall coercive field (Ec) via local field enhancements. Further, optically-nucleated polarization reversal appears to occur via stabilization of latent nuclei via the charge screening effects of free charges.« less

Modified Gold Electrode and Hollow Mn3O4 Nanoparticles as Electrode Materials for Microbial Fuel Cell Applications

NASA Astrophysics Data System (ADS)

Dhungana, Pramod

Microbial fuel cell (MFC) technology has attracted great attention in the scientific community as it offers the possibility of extraction of electricity from wide range of soluble and dissolved organic waste or renewable biomass, including sludge, waste water and cellulosic biomass. Microbial fuel cells are devices that utilize microbial metabolic processes to convert chemical energy via the oxidation of organic substances to produce electric current. MFCs consist of two chambers, an anode and cathode, separated by ion-permeable materials. The efficiency of producing electricity using the MFC depends on several factors such as immobilization of microorganisms on anode, mode of electron transfer, types of substrate/fuel and effectiveness of cathode materials for oxygen reduction reaction (ORR). In this work, in order to immobilize the microorganisms on anode materials, we have investigated the surface modification of gold electrode (anode) using alkyl dithiol and aryl thiol with glucose. The modification processes were characterized by using contact angle measurements and proton nuclear magnetic resonance (NMR). In order to study the effectiveness of cathode materials for ORR, we have synthesized hollow Mn3O 4 nanoparticles which are electrically very poor. Therefore, the hollow nanoparticles were mixed with electrically conductive multi-walled carbon nanotube as support and optimized the mixing process. This composite material shows enhanced ORR activity in all types of pH conditions. In future, we will focus to integrate anode and cathode in MFC to check its efficiency to produce electricity.

Mesoporous materials and nanocrystals for enhancing the dissolution behavior of poorly water-soluble drugs.

PubMed

Santos, Helder A; Peltonen, Leena; Limnell, Tarja; Hirvonen, Jouni

2013-01-01

Advanced drug delivery formulations are presently recognized as promising tools for overcoming the adverse physicochemical properties of conventional drug molecules, such as poor water solubility, which often leads to poor drug bioavailability. Oral drug delivery is considered as the easiest and most convenient route of drug administration. However, via the current trends utilizing combinatorial chemistry and high throughput screening in drug development, new drug molecules are moving towards lipophilic and poorly water-soluble large molecules, and the oral delivery route is becoming increasingly challenging. In this context, formulation of poorly soluble and/or permeable drugs using mesoporous materials and nanocrystals technology have proven to be highly successful due to the greater surface/volume ratio of these systems, resulting in improvements in dissolution and bioavailability, as well as enhanced drug permeability. This review addresses the issues of poorly water-soluble drugs with a major focus on recent developments in the application of the mesoporous materials (e.g., porous silicon and silica) and nanocrystals in drug delivery applications. In addition, we present several recent examples of the significant potential of these materials for the pharmaceutical field.

Fatigue crack propagation behavior of ultrahigh molecular weight polyethylene.

PubMed

Connelly, G M; Rimnac, C M; Wright, T M; Hertzberg, R W; Manson, J A

1984-01-01

The relative fatigue crack propagation resistance of plain and carbon fiber-reinforced ultrahigh molecular weight polyethylene (UHMWPE) was determined from cyclic loading tests performed on compact tension specimens machined from the tibial components of total knee prostheses. Both materials were characterized by dynamic mechanical spectroscopy, X-ray diffraction, and differential scanning calorimetry. The cyclic tests used loading in laboratory air at 5 Hz using a sinusoidal wave form. Dynamic mechanical spectroscopy showed that the reinforced UHMWPE had a higher elastic storage modulus than the plain UHMWPE, whereas X-ray diffraction and differential scanning calorimetry showed that the percent crystallinity and degree of order in the crystalline regions were similar for the two materials. Fatigue crack propagation in both materials proved to be very sensitive to small changes in the applied cyclic stress intensity range. A 10% increase in stress intensity resulted in approximately an order of magnitude increase in fatigue crack growth rate. The fatigue crack propagation resistance of the reinforced UHMWPE was found to be significantly worse than that of the plain UHMWPE. This result was attributed to poor bonding between the carbon fibers and the UHMWPE matrix and the ductile nature of the matrix itself.

Data from the Mars Science Laboratory CheMin XRD/XRF Instrument

NASA Technical Reports Server (NTRS)

Vaniman, David; Blake, David; Bristow, Tom; DesMarais, David; Achilles, Cherie; Anderson, Robert; Crips, Joy; Morookian, John Michael; Spanovich, Nicole; Vasavada, Ashwin;

Housing Conditions Contribute to Underweight in Children: An Example From Rural Villages in Southeast Sulawesi, Indonesia.

PubMed

Tasnim, Tasnim; Dasvarma, Gouranga; Mwanri, Lillian

2017-09-01

The prevalence of underweight in children under 5 years of age is anomalously high in Konawe District, Southeast Sulawesi Province, Indonesia. This state of affairs may be related to poor housing conditions, such as limited access to clean water, the absence of a sanitary latrine, and the use of poor housing materials. Therefore, this study aimed to examine the effect of housing conditions on underweight in under-5 children in Konawe District. This study was conducted in 2013 in 5 health centres in Konawe District, Southeast Sulawesi Province, and used a case-control study design. The study recruited 400 under-5 children, including 100 of whom were cases and 300 of whom were age-matched controls (1:3). Cases were underweight children, while the controls were children with a normal nutritional status. The independent variables were the availability and types of water and latrine facilities and housing materials (roof, wall, and floor). The statistical analysis used Cox regression. A lack of water availability (odds ratio [OR], 5.0; 95% confidence interval [CI], 2.7 to 9.5; p<0.001), a lack of latrine availability in the home (OR, 2.5; 95% CI, 1.5 to 4.0; p<0.001), and poor-quality roofing materials (OR, 1.7; 95% CI, 1.1 to 2.7; p<0.02) significantly contributed to underweight in children. In contrast, the walls and the floors did not contribute to under-5 year children being underweight (p=0.09 and p=0.71, respectively). Sanitation facilities and roofing were identified as important factors to address in order to improve children's nutritional status. Children's health status was directly impacted by food intake via their nutritional status.

Three perspectives on the mismatch between measures of material poverty.

PubMed

Hick, Rod

2015-03-01

The two most prominent measures of material poverty within contemporary European poverty analysis are low income and material deprivation. However, it is by now well-known that these measures identify substantially different people as being poor. In this research note, I seek to demonstrate that there are at least three ways to understand the mismatch between low income and material deprivation, relating to three different forms of identification: identifying poor households, identifying groups at risk of poverty and identifying trends in material poverty over time. Drawing on data from the British Household Panel Survey, I show that while low income and material deprivation identify very different households as being poor, and display distinct trends over time, in many cases they identify the same groups at being at risk of material poverty. © London School of Economics and Political Science 2014.

Development of an atmospheric monitoring plan for space station

NASA Technical Reports Server (NTRS)

Casserly, Dennis M.

1989-01-01

An environmental health monitoring plan for Space Station will ensure crew health during prolonged habitation. The Space Station, Freedom, will operate for extended periods, 90+ days, without resupply. A regenerative, closed loop life support system will be utilized in order to minimize resupply logistics and costs. Overboard disposal of wastes and venting of gases to space will be minimal. All waste material will be treated and recycled. The concentrated wastes will be stabilized and stored for ground disposal. The expected useful life of the station (decades) and the diversity of materials brought aboard for experimental or manufacturing purposes, increases the likelihood of cabin contamination. Processes by which cabin contamination can occur include: biological waste production, material off-gassing, process leakage, accidental containment breach, and accumulation due to poor removal efficiencies of the purification units. An industrial hygiene approach was taken to rationalize monitoring needs and to identify the substances likely to be present, the amount, and their hazard.

Friction Stir Welding of ODS and RAFM Steels

DOE PAGES

Yu, Zhenzhen; Feng, Zhili; Hoelzer, David; ...

2015-09-14

Advanced structural materials such as oxide dispersion strengthened steels and reduced-activation ferritic/martensitic steels are desired in fusion reactors as primary candidate materials for first wall and blanket structures, due to their excellent radiation and high-temperature creep resistance. However, their poor fusion weldability has been the major technical challenge limiting practical applications. For this reason, solid-state friction stir welding (FSW) has been considered for such applications. In this paper, the effect of FSW parameters on joining similar and dissimilar advanced structural steels was investigated. Scanning electron microscopy and electron backscatter diffraction methods were used to reveal the effects of FSW onmore » grain size, micro-texture distribution, and phase stability. Hardness mapping was performed to evaluate mechanical properties. Finally, post weld heat treatment was also performed to tailor the microstructure in the welds in order to match the weld zone mechanical properties to the base material.« less

Properties of Roman bricks and mortars used in Serapis temple in the city of Pergamon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ozkaya, Ozlem Aslan; Boeke, Hasan, E-mail: hasanboke@iyte.edu.tr

Serapis temple, which was constructed in the Roman period in the city of Pergamon (Bergama/Turkey), is one of the most important monuments of the world heritage. In this study, the characteristics of bricks and mortars used in the temple have been determined in order to define the necessary characteristics of the intervention materials, which will be used in the conservation works of the temple. Several analyses were carried out to determine their basic physical properties, raw material compositions, mineralogical and microstructural properties using X-ray diffraction, Scanning Electron Microscope and a Thermo Gravimetric Analyzer. Analysis results indicated that the mortars aremore » stiff, compact and hydraulic due to the use of natural pozzolanic aggregates. The Roman bricks are of low density, high porosity and were produced from raw materials containing calcium poor clays fired at low temperatures.« less

Evidence of nanocrystalline semiconducting graphene monoxide during thermal reduction of graphene oxide in vacuum.

PubMed

Mattson, Eric C; Pu, Haihui; Cui, Shumao; Schofield, Marvin A; Rhim, Sonny; Lu, Ganhua; Nasse, Michael J; Ruoff, Rodney S; Weinert, Michael; Gajdardziska-Josifovska, Marija; Chen, Junhong; Hirschmugl, Carol J

2011-12-27

As silicon-based electronics are reaching the nanosize limits of the semiconductor roadmap, carbon-based nanoelectronics has become a rapidly growing field, with great interest in tuning the properties of carbon-based materials. Chemical functionalization is a proposed route, but syntheses of graphene oxide (G-O) produce disordered, nonstoichiometric materials with poor electronic properties. We report synthesis of an ordered, stoichiometric, solid-state carbon oxide that has never been observed in nature and coexists with graphene. Formation of this material, graphene monoxide (GMO), is achieved by annealing multilayered G-O. Our results indicate that the resulting thermally reduced G-O (TRG-O) consists of a two-dimensional nanocrystalline phase segregation: unoxidized graphitic regions are separated from highly oxidized regions of GMO. GMO has a quasi-hexagonal unit cell, an unusually high 1:1 O:C ratio, and a calculated direct band gap of ∼0.9 eV.

Near-unity photoluminescence quantum yield in MoS.sub.2

DOEpatents

Amani, Matin; Lien, Der-Hsien; Kiriya, Daisuke; Bullock, James; Javey, Ali

2017-12-26

Two-dimensional (2D) transition-metal dichalcogenides have emerged as a promising material system for optoelectronic applications, but their primary figure-of-merit, the room-temperature photoluminescence quantum yield (QY) is extremely poor. The prototypical 2D material, MoS.sub.2 is reported to have a maximum QY of 0.6% which indicates a considerable defect density. We report on an air-stable solution-based chemical treatment by an organic superacid which uniformly enhances the photoluminescence and minority carrier lifetime of MoS.sub.2 monolayers by over two orders of magnitude. The treatment eliminates defect-mediated non-radiative recombination, thus resulting in a final QY of over 95% with a longest observed lifetime of 10.8.+-.0.6 nanoseconds. Obtaining perfect optoelectronic monolayers opens the door for highly efficient light emitting diodes, lasers, and solar cells based on 2D materials.

A Method to Predict the Thickness of Poorly-Bonded Material Along Spray and Spray-Layer Boundaries in Cold Spray Deposition

NASA Astrophysics Data System (ADS)

Li, Yangfan; Hamada, Yukitaka; Otobe, Katsunori; Ando, Teiichi

2017-02-01

Multi-traverse CS provides a unique means for the production of thick coatings and bulk materials from powders. However, the material along spray and spray-layer boundaries is often poorly bonded as it is laid by the leading and trailing peripheries of the spray that carry powder particles with insufficient kinetic energy. For the same reason, the splats in the very first layer deposited on the substrate may not be bonded well either. A mathematical spray model was developed based on an axisymmetric Gaussian mass flow rate distribution and a stepped deposition yield to predict the thickness of such poorly-bonded layers in multi-traverse CS deposition. The predicted thickness of poorly-bonded layers in a multi-traverse Cu coating falls in the range of experimental values. The model also predicts that the material that contains poorly bonded splats could exceed 20% of the total volume of the coating.

Optimal sample formulations for DNP SENS: The importance of radical-surface interactions

DOE PAGES

Perras, Frederic A.; Wang, Lin-Lin; Manzano, J. Sebastian; ...

2017-11-15

The efficacy of dynamic nuclear polarization (DNP) surface-enhanced NMR spectroscopy (SENS) is reviewed for alumina, silica, and ordered mesoporous carbon (OMC) materials, with vastly different surface areas, as a function of the biradical concentration. Importantly, our studies show that the use of a “one-size-fits-all” biradical concentration should be avoided when performing DNP SENS experiments and instead an optimal concentration should be selected as appropriate for the type of material studied as well as its surface area. In general, materials with greater surface areas require higher radical concentrations for best possible DNP performance. This result is explained with the use ofmore » a thermodynamic model wherein radical-surface interactions are expected to lead to an increase in the local concentration of the polarizing agent at the surface. We also show, using plane-wave density functional theory calculations, that weak radical-surface interactions are the cause of the poor performance of DNP SENS for carbonaceous materials.« less

EXAFS: New tool for study of battery and fuel cell materials

NASA Technical Reports Server (NTRS)

Mcbreen, James; Ogrady, William E.; Pandya, Kaumudi I.

1987-01-01

Extended X ray absorption fine structure (EXAFS) is a powerful technique for probing the local atomic structure of battery and fuel cell materials. The major advantages of EXAFS are that both the probe and the signal are X rays and the technique is element selective and applicable to all states of matter. This permits in situ studies of electrodes and determination of the structure of single components in composite electrodes, or even complete cells. EXAFS specifically probes short range order and yields coordination numbers, bond distances, and chemical identity of nearest neighbors. Thus, it is ideal for structural studies of ions in solution and the poorly crystallized materials that are often the active materials or catalysts in batteries and fuel cells. Studies on typical battery and fuel cell components are used to describe the technique and the capability of EXAFS as a structural tool in these applications. Typical experimental and data analysis procedures are outlined. The advantages and limitations of the technique are also briefly discussed.

An Explosives Products Thermodynamic Equation of State Appropriate for Material Acceleration and Overdriven Detonation: Theoretical Background and Formulation

DTIC Science & Technology

1991-07-01

provide poor representations of overdriven detonation. The Jones-Wilkens- Lee-Baker ( JWLB ) has been formulated to provide a more accurate representation...Chapman-Jouguet state. The resulting equation of state form, named Jones-Wilkens-Lee-Baker ( JWLB ), is P. A,[-+ e-R-iV -t-V-4- C(1 V(wl 1 where, ,=L(AAi...is the specific internal energy. The JWLB equation of state form is based on a first order expansion around the principal isentrope: A, .’ie’R iV + CV

Update on nail cosmetics.

PubMed

Jefferson, Julie; Rich, Phoebe

2012-01-01

Nail cosmetics are used by millions of people worldwide who desire smooth, lustrous nails. The nail cosmetic industry continues to expand to meet increasing consumer demand. In 2011 alone, consumers spent $6.6 billion on nail salon services. Although nail cosmetics are relatively safe, poor application techniques can promote disease, deformity, and allergic and irritant contact dermatitis. The foundation for managing nail cosmetic problems is prevention through education. Familiarity with the procedures and materials used in the nail cosmetic industry is necessary in order to recommend safe nail care strategies. © 2012 Wiley Periodicals, Inc.

Insertion of lattice strains into ordered LiNi0.5Mn1.5O4 spinel by mechanical stress: A comparison of perfect versus imperfect structures as a cathode for Li-ion batteries

NASA Astrophysics Data System (ADS)

Kozawa, Takahiro; Murakami, Takeshi; Naito, Makio

2016-07-01

The Ni-doped lithium manganese oxide, LiNi0.5Mn1.5O4, has received much attention as a cathode active material in high-energy lithium-ion batteries (LIBs). This active material has two different spinel structures depending on the ordering state of the Ni and Mn ions. The ordered LiNi0.5Mn1.5O4 spinel has an inferior cathode performance than the disordered phase because of its poor electronic conductivity. However, the ordered LiNi0.5Mn1.5O4 spinel possesses the potential advantage of avoiding dissolution of the Mn ion, which is an issue for the disordered spinel. The improvement of cathode performance is important for future applications. Here, we report a unique approach to improve the cathode performance of the ordered LiNi0.5Mn1.5O4 spinel. The mechanical treatment using an attrition-type mill successfully inserted lattice strains into the ordered LiNi0.5Mn1.5O4 spinel structure without a phase transformation to the disordered phase. The insertion of lattice strains by mechanical stresses provided an increased discharge capacity and a decreased charge transfer resistance. This limited crystal structure modification improved the cathode performance. The present work has the potential for application of the mechanically treated ordered LiNi0.5Mn1.5O4 spinel as a cathode for high-energy LIBs.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brandt, Riley E.; Mangan, Niall M.; Li, Jian V.

The development of new thin-film photovoltaic (PV) absorbers is often hindered by the search for an optimal heterojunction contact; an unoptimized contact may be mistaken for poor quality of the underlying absorber, making it difficult to assess the reasons for poor performance. Therefore, quantifying the loss in device efficiency and open-circuit voltage (VOC) as a result of the interface is a critical step in evaluating a new material. In the present work, we fabricate thin-film PV devices using cuprous oxide (Cu2O), with several different n-type heterojunction contacts. Their current-voltage characteristics are measured over a range of temperatures and illumination intensitiesmore » (JVTi). We quantify the loss in VOC due to the interface and determine the effective energy gap at the interface. The effective interface gap measured by JVTi matches the gap measured by X-ray photoelectron spectroscopy, albeit with higher energy resolution and an order of magnitude faster. We discuss potential artifacts in JVTi measurements and areas where analytical models are insufficient. Applying JVTi to complete devices, rather than incomplete material stacks, suggests that it can be a quick, accurate method to assess the loss due to unoptimized interface band offsets in thin-film PV devices.« less

Trends in the precipitation and crystallization behavior of supersaturated aqueous solutions of poorly water-soluble drugs assessed using synchrotron radiation.

PubMed

Raina, Shweta A; Van Eerdenbrugh, Bernard; Alonzo, David E; Mo, Huaping; Zhang, Geoff G Z; Gao, Yi; Taylor, Lynne S

2015-06-01

Amorphous materials are high-energy solids that can potentially enhance the bioavailability of poorly soluble compounds. A major impediment to their widespread use as a formulation platform is the tendency of amorphous materials to crystallize. The aim of this study was to evaluate the relative crystallization tendency of six structural analogues belonging to the dihydropyridine class, in an aqueous environment in the absence and presence of polymers, using wide-angle X-ray scattering synchrotron radiation and polarized light microscopy. The crystallization behavior of precipitates generated from supersaturated solutions of the active pharmaceutical ingredients was found to be highly variable ranging from immediate to several hours in the absence of polymers. Polymers with intermediate hydrophilicity/hydrophobicity were found to substantially delay crystallization, whereas strongly hydrophilic or hydrophobic polymers were largely ineffective. Nuclear magnetic resonance spectroscopy experiments supported the supposition that polymers need to have affinity for both the drug-rich precipitate and the aqueous phase in order to be effective crystallization inhibitors. This study highlights the variability in the crystallization tendency of different compounds and provides insight into the mechanism of inhibition by polymeric additives. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Understanding the application of Raman spectroscopy to the detection of traces of life.

PubMed

Marshall, Craig P; Edwards, Howell G M; Jehlicka, Jan

2010-03-01

Investigating carbonaceous microstructures and material in Earth's oldest sedimentary rocks is an essential part of tracing the origins of life on our planet; furthermore, it is important for developing techniques to search for traces of life on other planets, for example, Mars. NASA and ESA are considering the adoption of miniaturized Raman spectrometers for inclusion in suites of analytical instrumentation to be placed on robotic landers on Mars in the near future to search for fossil or extant biomolecules. Recently, Raman spectroscopy has been used to infer a biological origin of putative carbonaceous microfossils in Early Archean rocks. However, it has been demonstrated that the spectral signature obtained from kerogen (of known biological origin) is similar to spectra obtained from many poorly ordered carbonaceous materials that arise through abiotic processes. Yet there is still confusion in the literature as to whether the Raman spectroscopy of carbonaceous materials can indeed delineate a signature of ancient life. Despite the similar nature in spectra, rigorous structural interrogation between the thermal alteration products of biological and nonbiological organic materials has not been undertaken. Therefore, we propose a new way forward by investigating the second derivative, deconvolution, and chemometrics of the carbon first-order spectra to build a database of structural parameters that may yield distinguishable characteristics between biogenic and abiogenic carbonaceous material. To place Raman spectroscopy as a technique to delineate a biological origin for samples in context, we will discuss what is currently accepted as a spectral signature for life; review Raman spectroscopy of carbonaceous material; and provide a historical overview of Raman spectroscopy applied to Archean carbonaceous materials, interpretations of the origin of the ancient carbonaceous material, and a future way forward for Raman spectroscopy.

Recent work on material interface reconstruction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mosso, S.J.; Swartz, B.K.

1997-12-31

For the last 15 years, many Eulerian codes have relied on a series of piecewise linear interface reconstruction algorithms developed by David Youngs. In a typical Youngs` method, the material interfaces were reconstructed based upon nearly cell values of volume fractions of each material. The interfaces were locally represented by linear segments in two dimensions and by pieces of planes in three dimensions. The first step in such reconstruction was to locally approximate an interface normal. In Youngs` 3D method, a local gradient of a cell-volume-fraction function was estimated and taken to be the local interface normal. A linear interfacemore » was moved perpendicular to the now known normal until the mass behind it matched the material volume fraction for the cell in question. But for distorted or nonorthogonal meshes, the gradient normal estimate didn`t accurately match that of linear material interfaces. Moreover, curved material interfaces were also poorly represented. The authors will present some recent work in the computation of more accurate interface normals, without necessarily increasing stencil size. Their estimate of the normal is made using an iterative process that, given mass fractions for nearby cells of known but arbitrary variable density, converges in 3 or 4 passes in practice (and quadratically--like Newton`s method--in principle). The method reproduces a linear interface in both orthogonal and nonorthogonal meshes. The local linear approximation is generally 2nd-order accurate, with a 1st-order accurate normal for curved interfaces in both two and three dimensional polyhedral meshes. Recent work demonstrating the interface reconstruction for curved surfaces will /be discussed.« less

Adaptable and adaptive materials for light flux control

NASA Astrophysics Data System (ADS)

Sixou, Pierre; Magnaldo, A.; Nourry, J.; Laye, C.

1996-04-01

The purpose of this paper is to describe and examine properties of light flux control materials. Indeed, intelligent light flux control is necessary not only to improve everyday visual convenience but also in an economical point of view in order to reduce global home energetic cost. Several types of materials are good potential candidates for such functions: (1) The most well-known investigations concern inorganic materials such as tungsten or molybdenum oxides in which an electrochrom layer darkens when enriched in ions, and looses its color when impoverished. Unfortunately, at the moment, there is no convenient way to realize correct ions suppliers. Moreover, other drawbacks arise, such as poor reversibility, reactive interferences or a sensitivity of the material to its environment. These systems only need a low voltage level to work. But, their dynamic response, which is correlated to the component surface, is quite long. (2) At the present time, another attractive issue seems promising. More and more studies concern micro-composite liquid crystal films. For first, we shall remind their principles as well as their way of preparation. After having talked about their main advantages as intelligent materials, we shall discuss their control, their light flux adaptability, or their memory capabilities.

Sorting it out: bedding particle size and nesting material processing method affect nest complexity.

PubMed

Robinson-Junker, Amy; Morin, Amelia; Pritchett-Corning, Kathleen; Gaskill, Brianna N

2017-04-01

As part of routine husbandry, an increasing number of laboratory mice receive nesting material in addition to standard bedding material in their cages. Nesting material improves health outcomes and physiological performance in mice that receive it. Providing usable nesting material uniformly and efficiently to various strains of mice remains a challenge. The aim of this study was to determine how bedding particle size, method of nesting material delivery, and processing of the nesting material before delivery affected nest building in mice of strong (BALB/cAnNCrl) and weak (C3H/HeNCrl) gathering abilities. Our data suggest that processing nesting material through a grinder in conjunction with bedding material, although convenient for provision of bedding with nesting material 'built-in', negatively affects the integrity of the nesting material and subsequent nest-building outcomes. We also found that C3H mice, previously thought to be poor nest builders, built similarly scored nests to those of BALB/c mice when provided with unprocessed nesting material. This was true even when nesting material was mixed into the bedding substrate. We also observed that when nesting material was mixed into the bedding substrate, mice of both strains would sort their bedding by particle size more often than if it were not mixed in. Our findings support the utility of the practice of distributing nesting material mixed in with bedding substrate, but not that of processing the nesting material with the bedding in order to mix them.

Up-and-coming IMCs. [Intermetallic-Matrix Composites

NASA Technical Reports Server (NTRS)

Bowman, Randy; Noebe, Ronald

1989-01-01

While the good oxidation and environmental resistance, high melting points, and comparatively low densities of such ordered intermetallics as Ti3Al, NiAl, FeAl, and NbAl3 render them good candidates for advanced aerospace structures, their poor toughness at low temperatures and low strength at elevated temperatures have prompted the development of fiber-reinforced intermetallic-matrix composites (IMCs) with more balanced characteristics. Fabrication methods for continuous-fiber IMCs under development include the P/M 'powder cloth' method, the foil/fiber method, and thermal spraying. The ultimate success of IMCs depends on fibers truly compatible with the matrix materials.

Electric Switching of Fluorescence Decay in Gold-Silica-Dye Nematic Nanocolloids Mediated by Surface Plasmons.

PubMed

Jiang, Li; Mundoor, Haridas; Liu, Qingkun; Smalyukh, Ivan I

2016-07-26

Tunable composite materials with interesting physical behavior can be designed through integrating unique optical properties of solid nanostructures with facile responses of soft matter to weak external stimuli, but this approach remains challenged by their poorly controlled coassembly at the mesoscale. Using scalable wet chemical synthesis procedures, we fabricated anisotropic gold-silica-dye colloidal nanostructures and then organized them into the device-scale (demonstrated for square-inch cells) electrically tunable composites by simultaneously invoking molecular and colloidal self-assembly. We show that the ensuing ordered colloidal dispersions of shape-anisotropic nanostructures exhibit tunable fluorescence decay rates and intensity. We characterize how these properties depend on low-voltage fields and polarization of both the excitation and emission light, demonstrating a great potential for the practical realization of an interesting breed of nanostructured composite materials.

Teaching Reform of Civil Engineering Materials Course Based on Project-Driven Pedagogy

NASA Astrophysics Data System (ADS)

Yidong, Xu; Wei, Chen; WeiguoJian, You; Jiansheng, Shen

2018-05-01

In view of the scattered experimental projects in practical courses of civil engineering materials, the poor practical ability of students and the disconnection between practical teaching and theoretical teaching, this paper proposes a practical teaching procedure. Firstly, the single experiment should be offered which emphasizes on improving the students’ basic experimental operating ability. Secondly, the compressive experiment is offered and the overall quality of students can be examined in the form of project team. In order to investigate the effect of teaching reform, the comparative analysis of the students of three grades (2014, 2015 and 2016) majored in civil engineering was conducted. The result shows that the students’ ability of experimental operation is obviously improved by using the project driven method-based teaching reform. Besides, the students’ ability to analyse and solve problems has also been improved.

Online maritime health information: an overview of the situation.

PubMed

Guitton, Matthieu J

2015-01-01

Due to their working conditions, seafarers often don't benefit from the same medical coverage than the onshore population. Therefore, seafarers and their relatives often need to locate health information by themselves. While the rise of the Internet has drastically transformed the way people can gather information, the availability of specific maritime health information online still need to be evaluated scientifically. We aim here to document of the characteristic of maritime health-related online information. A web survey was performed, articulated on two complementary analyses. First, an overall analysis of websites related to maritime health compared to websites related to two other health areas relevant for the general population (dental health and otorhinolaryngology) used as control. Second, an analysis of the understandability and actionability of a series of Wikipedia articles related to pathologies relevant for seafarers using the Patient Education Materials Assessment Tool (PEMAT). Online resources associated with maritime health were sparse and difficult to locate. When compared to other medical fields, maritime health websites were extremely poor in displaying useful information for seafarers. Available online resources regarding specific diseases affecting seafarers were mainly not adapted for a general audience and scored poorly both in terms of understandability and of actionability. This study provides a general overview of the degree of adaption of online material related to maritime health to seafarers' potential needs. Considerably more efforts need to be made in order to provide controlled online materials to answer the health information needs of the seafarers and their relatives.

Stability and Reactivity: Positive and Negative Aspects for Nanoparticle Processing.

PubMed

Xu, Liang; Liang, Hai-Wei; Yang, Yuan; Yu, Shu-Hong

2018-04-11

Nanoparticles exist far from the equilibrium state due to their high surface energy. Nanoparticles are therefore extremely unstable and easily change themselves or react with active substances to reach a relatively stable state in some cases. This causes desired changes or undesired changes to nanoparticles and thus makes them exhibit a high reactivity and a poor stability. Such dual nature (poor stability and high reactivity) of nanoparticles may result in both negative and positive effects for nanoparticle processing. However, the existing studies mainly focus on the high reactivity of nanoparticles, whereas their poor stability has been neglected or considered inconsequential. In fact, in some cases the unstable process, which is derived from the poor stability of nanoparticles, offers an opportunity to design and fabricate unique nanomaterials, such as by chemically transforming the "captured" intermediate nanostructures during a changing process, assembling destabilized nanoparticles into larger ordered assemblies, or shrinking/processing pristine materials into the desired size or shape via selective etching. In this review, we aim to present the stability and reactivity of nanoparticles on three levels: the foundation, concrete manifestations, and applications. We start with a brief introduction of dangling bonds and the surface chemistry of nanoparticles. Then, concrete manifestations of the poor stability and high reactivity of nanoparticles are presented from four perspectives: dispersion stability, thermal stability, structural stability, and chemical stability/reactivity. Next, we discuss some issues regarding the stability and reactivity of nanomaterials during applications. Finally, conclusions and perspectives on this field are presented.

Functionalized Poly(3,4-ethylenedioxy bithiophene) Films for Tuning Electrochromic and Thermoelectric Properties.

PubMed

Hu, Yongjing; Liu, Xiaofang; Jiang, Fengxing; Zhou, Weiqiang; Liu, Congcong; Duan, Xuemin; Xu, Jingkun

2017-10-05

Conductive thiophene-based polymers have garnered great attention for use in organic electron materials such as electrochromic and thermoelectric materials. However, they suffer from poor electron transport properties and long-term stability, leading to limited development eventually. Here, we proposed a strategy of functionalized thiophene-based polymers with oligo(ethylene glycol) or alkyl side chains and synthesized a series of poly(3,4-ethylenedioxy bithiophene)s (PEDTs) to tune their electrochromic and thermoelectric properties. An alkyl group bearing electronic ability at the thiophene ring effectively achieved a large increase in the electrical conductivity with nearly invariable Seebeck coefficient, resulting in an enhancement by 1 order of magnitude for the thermoelectric power factor. Moreover, the electrochromic properties of functionalized PEDTs gained an effective improvement in the optical contrast and coloration efficiency as well as stability with multicolor changes between neutral and oxidized states. The functionalized PEDTs can be proposed as an alternative strategy to tune the electrochromic and thermoelectric properties for organic polymer materials.

Multiple sensor multifrequency eddy current monitor for solidification and growth

NASA Technical Reports Server (NTRS)

Wallace, John

1990-01-01

A compact cylindrical multisensor eddy current measuring system with integral furnace was develop to monitor II-VI crystal growth to provide interfacial information, solutal segregation, and conductivities of the growth materials. The use of an array of sensors surrounding the furnace element allows one to monitor the volume of interest. Coupling these data with inverse multifrequency analysis allows radial conductivity profiles to be generated at each sensor position. These outputs were incorporated to control the processes within the melt volume. The standard eddy current system functions with materials whose electric conductivities are as low as 2E2 Mhos/m. A need was seen to extend the measurement range to poorly conducting media so the unit was modified to allow measurement of materials conductivities 4 order of magnitude lower and bulk dielectric properties. Typically these included submicron thick films and semiinsulating GaAs. This system was used to monitor complex heat transfer in grey bodies as well as semiconductor and metallic solidification.

Li-Ion Cell Development for Low Temperature Applications

NASA Technical Reports Server (NTRS)

Huang, C.-K.; Sakamoto, J. S.; Surampudi, S.; Wolfenstine, J.

2000-01-01

JPL is involved in the development of rechargeable Li-ion cells for future Mars Exploration Missions. The specific objectives are to improve the Li-ion cell cycle life performance and rate capability at low temperature (<<-20 C) in order to enhance survivability of the Mars lander and rover batteries. Poor Li-ion rate capability at low temperature has been attributed to: (1) the electrolytes becoming viscous or freezing and/or (2) reduced electrode capacity that results from decreased Li diffusivity. Our efforts focus on increasing the rate capability at low temperature for Li-ion cells. In order to improve the rate capability we evaluated the following: (1) cathode performance at low temperatures, (2) electrode active material particle size on low temperature performance and (3) Li diffusivity at room temperature and low temperatures. In this paper, we will discuss the results of our study.

Structure and Properties of Azobenzene Thin-Films

NASA Astrophysics Data System (ADS)

Allen, R. A.

1987-09-01

Available from UMI in association with The British Library. A number of monomer and polymer materials, all containing the azobenzene group, have been deposited as Langmuir-Blodgett (LB) multilayers and their structures and physical properties studied. LB films of two monomeric materials exhibited liquid crystal phase changes that were investigated by optical microscopy and X-ray diffraction. Multilayers built up from one of the materials exhibited a phase change upon aging and this demonstrated that the LB technique had produced a structure that was not the equilibrium state. A monomer material possessing a fluorocarbon chain was found to initially deposit as an LB film in a Z-type manner, but changed to Y-type deposition with increasing multilayer thickness. A correlation was observed between this behaviour and the surface potential changes that were brought about when deposition took place on an aluminium substrate. The feasibility of building up alternating multilayers of monomer and polymer materials was demonstrated. Combining these two classes of material in the same LB film may confer on it the mechanical durability of the polymers and the highly ordered structure and potentially interesting physical properties of the monomer. The structures developed here may prove to have high second harmonic generation capabilities. Polymer materials were built up into relatively thick Y-type LB multilayers and studied by X-ray diffraction. Only poorly defined layered structures were found. Polymer materials were also cast into thin films from the melt and from solution. One of the compounds developed a high degree of anisotropy in its structure after exposure to linearly polarised white light. A birefringence of up to Deltan = 0.21 was measured. In contrast, LB films formed from the same material could not be ordered in the same manner and this appeared to result from the very close packing that takes place in such structures.

Repetition and comprehension of spoken sentences by reading-disabled children.

PubMed

Shankweiler, D; Smith, S T; Mann, V A

1984-11-01

The language problems of reading-disabled elementary school children are not confined to written language alone. These children often exhibit problems of ordered recall of verbal materials that are equally severe whether the materials are presented in printed or in spoken form. Sentences that pose problems of pronoun reference might be expected to place a special burden on short-term memory because close grammatical relationships obtain between words that are distant from one another. With this logic in mind, third-grade children with specific reading disability and classmates matched for age and IQ were tested on five sentence types, each of which poses a problem in assigning pronoun reference. On one occasion the children were tested for comprehension of the sentences by a forced-choice picture verification task. On a later occasion they received the same sentences as a repetition test. Good and poor readers differed significantly in immediate recall of the reflexive sentences, but not in comprehension of them as assessed by picture choice. It was suggested that the pictures provided cues which lightened the memory load, a possibility that could explain why the poor readers were not demonstrably inferior in comprehension of the sentences even though they made significantly more errors than the good readers in recalling them.

X-Ray Amorphous Phases in Terrestrial Analog Volcanic Sediments: Implications for Amorphous Phases in Gale Crater, Mars

NASA Technical Reports Server (NTRS)

Smith, R. J.; Horgan, B.; Rampe, E.; Dehouck, E.; Morris, R. V.

2017-01-01

X-ray diffraction (XRD) amorphous phases have been found as major components (approx.15-60 wt%) of all rock and soil samples measured by the CheMin XRD instrument in Gale Crater, Mars. The nature of these phases is not well understood and could be any combination of primary (e.g., glass) and secondary (e.g., allophane) phases. Amorphous phases form in abundance during surface weathering on Earth. Yet, these materials are poorly characterized, and it is not certain how properties like composition and structure change with formation environment. The presence of poorly crystalline phases can be inferred from XRD patterns by the appearance of a low angle rise (< or approx.10deg 2(theta)) or broad peaks in the background at low to moderate 2(theta) angles (amorphous humps). CheMin mineral abundances combined with bulk chemical composition measurements from the Alpha Particle X-ray Spectrometer (APXS) have been used to estimate the abundance and composition of the XRD amorphous materials in soil and rock samples on Mars. Here we apply a similar approach to a diverse suite of terrestrial samples - modern soils, glacial sediments, and paleosols - in order to determine how formation environment, climate, and diagenesis affect the abundance and composition of X-ray amorphous phases.

Role of solvent in metal-on-metal surface diffusion: A case for rational solvent selection for materials synthesis

NASA Astrophysics Data System (ADS)

Imandi, Venkataramana; Jagannath, Mantha Sai Pavan; Chatterjee, Abhijit

2018-09-01

The effect of solvent on diffusion at metal surfaces is poorly understood despite its importance to morphological evolution during materials processing, corrosion and catalysis. In this article, we probe the metal-solvent interfacial structure, effective nature of interactions and dynamics when a solvent is in contact with a metal using a novel accelerated molecular dynamics simulation technique called temperature programmed molecular dynamics (TPMD). TPMD simulations reveal that surface diffusion of metal-on-metal can be made to vary over orders-of-magnitude by tuning the metal-solvent interaction. Ultimately, the solvent can have an indirect effect on diffusion. As the solvent tugs at the metal surface the separation between the adsorbed metal atom (adatom) and the surface layer can be modulated via metal-solvent interactions. The resulting adatom-surface separation can cause stronger/weaker binding of the adatom to the metal surface, which in turn results in the observed slower/enhanced diffusion in the presence of solvent. We believe this effect is ubiquitous in pure metal and metal alloys and in principle one could rationally select solvent to control the material structural evolution. Implications on materials synthesis are discussed in the context of formation of nanoporous materials.

Probing the structure of heterogeneous diluted materials by diffraction tomography.

PubMed

Bleuet, Pierre; Welcomme, Eléonore; Dooryhée, Eric; Susini, Jean; Hodeau, Jean-Louis; Walter, Philippe

2008-06-01

The advent of nanosciences calls for the development of local structural probes, in particular to characterize ill-ordered or heterogeneous materials. Furthermore, because materials properties are often related to their heterogeneity and the hierarchical arrangement of their structure, different structural probes covering a wide range of scales are required. X-ray diffraction is one of the prime structural methods but suffers from a relatively poor detection limit, whereas transmission electron analysis involves destructive sample preparation. Here we show the potential of coupling pencil-beam tomography with X-ray diffraction to examine unidentified phases in nanomaterials and polycrystalline materials. The demonstration is carried out on a high-pressure pellet containing several carbon phases and on a heterogeneous powder containing chalcedony and iron pigments. The present method enables a non-invasive structural refinement with a weight sensitivity of one part per thousand. It enables the extraction of the scattering patterns of amorphous and crystalline compounds with similar atomic densities and compositions. Furthermore, such a diffraction-tomography experiment can be carried out simultaneously with X-ray fluorescence, Compton and absorption tomographies, enabling a multimodal analysis of prime importance in materials science, chemistry, geology, environmental science, medical science, palaeontology and cultural heritage.

Sensitivity of WallDYN material migration modeling to uncertainties in mixed-material surface binding energies

DOE PAGES

Nichols, J. H.; Jaworski, M. A.; Schmid, K.

2017-03-09

The WallDYN package has recently been applied to a number of tokamaks to self-consistently model the evolution of mixed-material plasma facing surfaces. A key component of the WallDYN model is the concentration-dependent surface sputtering rate, calculated using SDTRIM.SP. This modeled sputtering rate is strongly influenced by the surface binding energies (SBEs) of the constituent materials, which are well known for pure elements but often are poorly constrained for mixed-materials. This work examines the sensitivity of WallDYN surface evolution calculations to different models for mixed-material SBEs, focusing on the carbon/lithium/oxygen/deuterium system present in NSTX. A realistic plasma background is reconstructed frommore » a high density, H-mode NSTX discharge, featuring an attached outer strike point with local density and temperature of 4 × 10 20 m -3 and 4 eV, respectively. It is found that various mixed-material SBE models lead to significant qualitative and quantitative changes in the surface evolution profile at the outer divertor, with the highest leverage parameter being the C-Li binding model. Uncertainties of order 50%, appearing on time scales relevant to tokamak experiments, highlight the importance of choosing an appropriate mixed-material sputtering representation when modeling the surface evolution of plasma facing components. Lastly, these results are generalized to other fusion-relevant materials with different ranges of SBEs.« less

Sensitivity of WallDYN material migration modeling to uncertainties in mixed-material surface binding energies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nichols, J. H.; Jaworski, M. A.; Schmid, K.

The WallDYN package has recently been applied to a number of tokamaks to self-consistently model the evolution of mixed-material plasma facing surfaces. A key component of the WallDYN model is the concentration-dependent surface sputtering rate, calculated using SDTRIM.SP. This modeled sputtering rate is strongly influenced by the surface binding energies (SBEs) of the constituent materials, which are well known for pure elements but often are poorly constrained for mixed-materials. This work examines the sensitivity of WallDYN surface evolution calculations to different models for mixed-material SBEs, focusing on the carbon/lithium/oxygen/deuterium system present in NSTX. A realistic plasma background is reconstructed frommore » a high density, H-mode NSTX discharge, featuring an attached outer strike point with local density and temperature of 4 × 10 20 m -3 and 4 eV, respectively. It is found that various mixed-material SBE models lead to significant qualitative and quantitative changes in the surface evolution profile at the outer divertor, with the highest leverage parameter being the C-Li binding model. Uncertainties of order 50%, appearing on time scales relevant to tokamak experiments, highlight the importance of choosing an appropriate mixed-material sputtering representation when modeling the surface evolution of plasma facing components. Lastly, these results are generalized to other fusion-relevant materials with different ranges of SBEs.« less

Optical properties of iron oxides

NASA Astrophysics Data System (ADS)

Musfeldt, Janice

2012-02-01

Magnetoelectric coupling in materials like multiferroics, dilute magnetic semiconductors, and topological insulators has attracted a great deal of attention, although most work has been done in the static limit. Optical spectroscopy offers a way to investigate the dynamics of charge-spin coupling, an area where there has been much less effort. Using these techniques, we discovered that charge fluctuation in LuFe2O4, the prototypical charge ordered multiferroic, has an onset well below the charge ordering transition, supporting the ``order by fluctuation'' mechanism for the development of charge order superstructure. Bragg splitting and large magneto-optical contrast suggest a low temperature monoclinic distortion that can be driven by both temperature and magnetic field. At the same time, dramatic splitting of the LuO2 layer phonon mode is attributed to charge-rich/poor proximity effects, and its temperature dependence reveals the antipolar nature of the W layer pattern. Using optical techniques, we also discovered that α-Fe2O3, a chemically-similar parent compound and one of the world's oldest and most iconic antiferromagnetic materials, appears more red in applied magnetic field than in zero field conditions. This effect is driven by a field-induced reorientation of magnetic order. The oscillator strength lost in the color band is partially transferred to the magnon side band, a process that also reveals a new exciton pattern induced by the modified exchange coupling. Analysis of the exciton pattern exposes C2/c monoclinic symmetry in the high field phase of hematite. Taken together, these findings advance our understanding of iron-based materials under extreme conditions. [4pt] Collaborators include: X. S. Xu, P. Chen, Q. -C. Sun, T. V. Brinzari (Tennessee); S. McGill (NHMFL); J. De Groot, M. Angst, R. P. Hermann (Julich); A. D. Christianson, B. C. Sales, D. Mandrus (ORNL); A. P. Litvinchuk (Houston); J. -W. Kim (Ames); Z. Islam (Argonne); N. Lee, S. -W. Cheong (Rutgers).

Nanoscale Electronic Transport Studies of Novel Strongly Correlated Materials

NASA Astrophysics Data System (ADS)

Hardy, Will J.

Strongly correlated materials are those in which the electron-electron and electron-lattice interactions play pivotal roles in determining many aspects of observable physical behavior, including the electronic and magnetic properties. In this thesis, I describe electronic transport studies of novel strongly correlated materials at the nanoscale. After introducing some basic concepts, briefly reviewing historical development of the field, and discussing the process of making measurements on small length scales, I detail experimental results from studies of four specific materials: two transition metal oxide systems, and two layered transition metal dichalcogenides with intercalated magnetic moments. The first system is a modified version of a classic strongly correlated material, vanadium dioxide (VO2), which here is doped with hydrogen to suppress its metal-insulator transition and stabilize a poorly metallic phase down to liquid helium temperatures. Doped VO2 nanowires, micron flakes, and thin films display magnetoresistance (MR) consistent with weak localization physics, along with mesoscopic resistance fluctuations over short distances, raising questions about how to model transport in bad-metal correlated systems. A second transition metal oxide system is considered next: Quantum wells in SrTiO3 sandwiched between layers of SmTiO3, in which anomalous voltage fluctuation behavior is observed in etched nanostructures at low temperatures. After well-understood alternative origins are ruled out, an explanation is proposed involving a time-varying thermopower due to two-level fluctuations of etching-induced defects. Next, I shift to the topic of layered itinerant magnetic materials with intercalated moments, starting with Fe0.28TaS 2, a hard ferromagnet (FM) with strong spin-orbit coupling. Here, a surprisingly large MR of nearly 70% is observed, an especially striking feature given that the closely related compounds at Fe intercalation fractions of 1/4 or 1/3 have MR nearly two orders of magnitude smaller. In the latter compounds, the Fe atoms are arranged in ordered superlattices, whereas for the 0.28 case, a portion of the Fe moments deviate from ordered arrangement and are relatively easily flipped by an external magnetic field to be anti-aligned with neighboring ordered Fe moments. This situation, combined with strong spin-orbit coupling, results in enhanced charge carrier scattering and greatly increased resistance. The thesis concludes with a study of a second layered magnetic material, V5S8 (structurally equivalent to V0.25VS2), which is found to have a magnetic field driven phase transition at low temperatures, believed to be from antiferromagnetism to paramagnetism. This transition is first order in thick crystals, but becomes second order as the crystal thickness decreases toward 10 nm. Together, the experiments described in this thesis highlight the complexity and diversity of strongly correlated materials, while showcasing the power of nanoscale electronic transport in delivering an improved understanding of these systems.

Mesoporous systems for poorly soluble drugs.

PubMed

Xu, Wujun; Riikonen, Joakim; Lehto, Vesa-Pekka

2013-08-30

Utilization of inorganic mesoporous materials in formulations of poorly water-soluble drugs to enhance their dissolution and permeation behavior is a rapidly growing area in pharmaceutical materials research. The benefits of mesoporous materials in drug delivery applications stem from their large surface area and pore volume. These properties enable the materials to accommodate large amounts of payload molecules, protect them from premature degradation, and promote controlled and fast release. As carriers with various morphologies and chemical surface properties can be produced, these materials may even promote adsorption from the gastrointestinal tract to the systemic circulation. The main concern regarding their clinical applications is still the safety aspect even though most of them have been reported to be safely excreted, and a rather extensive toxicity screening has already been conducted with the most frequently studied mesoporous materials. In addition, the production of the materials on a large scale and at a reasonable cost may be a challenge when considering the utilization of the materials in industrial processes. However, if mesoporous materials could be employed in the industrial crystallization processes to produce hybrid materials with poorly soluble compounds, and hence to enhance their oral bioavailability, this might open new avenues for the pharmaceutical industry to employ nanotechnology in their processes. Copyright © 2012 Elsevier B.V. All rights reserved.

Elastic, viscoelastic and viscoplastic contributions to compliance during deformation under stress in prosthodontic temporization materials.

PubMed

Vaidyanathan, Tritala K; Vaidyanathan, Jayalakshmi; Arghavani, David

2016-12-01

Purpose: The goal of this investigation was to characterize the compliance properties in selected polymers used for temporary (provisional crown and bridge) applications. Method: Polymethyl methacrylate (PMMA)- and polyethyl methacrylate (PEMA)-based JET and TRIM II were investigated along with two bisacryl composite resins (LUXATEMP and PROTEMP 3 GARANT). Rectangular samples of the resins were subjected to creep-recovery tests in a dynamic mechanical analyzer at and near the oral temperature (27 °C, 37 °C and 47 °C). The instantaneous (elastic), and time-dependent viscoelastic, and viscoplastic compliance profiles of the materials were determined and analyzed as a function of materials and temperature. Results: Highly significant ( p = 0.0001) differences among means of elastic, viscoelastic and viscoplastic compliance values were found as a function of materials. TRIM II showed an order of magnitude higher viscoplastic deformation than the other three materials (LUXATEMP, PROTEMP 3 GARANT and JET). Conclusions: The results indicate that PEMA is susceptible to significantly greater elastic, viscoelastic, and more importantly to viscoplastic compliant behavior compared with bisacryl composite and PMMA provisional crown and bridge materials. This indicates high-dimensional instability and poor stiffness and resiliency in PEMA appliances vis-à-vis those of PMMA and bisacryl composites.

Adverse reactions to orthodontic materials.

PubMed

Sifakakis, I; Eliades, T

2017-03-01

Adverse effects can arise from the clinical use of orthodontic materials, due to the release of constituent substances (ions from alloys and monomers, degradation by-products, and additives from polymers). Moreover, intraoral aging affects the biologic properties of materials. The aim of this review is to present the currently identified major adverse effects of the metallic and polymeric components found in orthodontic appliances and materials. Corrosion in metallic orthodontic attachments releases metal ions, mainly iron, chromium, and nickel. The latter has received the greatest attention because of its reported potential for an allergic response. The formation of an oxide layer may inhibit the outward movement of ions, thereby acting as an obstacle for release. Titanium alloys have superior corrosion resistance than stainless steel. The efficiency of polymerisation is considered an essential property for all polymers. A poor polymer network is susceptible to the release of biologically reactive substances, such as bisphenol-A (BPA), which is capable of inducing hormone-related effects. The close proximity of a light-curing tip to the adhesive, pumice prophylaxis after bonding, indirect irradiation and mouth rinsing during the first hour after bonding may decrease BPA release. The adverse effects of some orthodontic materials should be considered during material selection and throughout orthodontic treatment, in order to minimise possible undesirable implications. © 2017 Australian Dental Association.

Structure and crystallography of foliated and chalk shell microstructures of the oyster Magallana: the same materials grown under different conditions.

PubMed

Checa, Antonio G; Harper, Elizabeth M; González-Segura, Alicia

2018-05-14

Oyster shells are mainly composed of layers of foliated microstructure and lenses of chalk, a highly porous, apparently poorly organized and mechanically weak material. We performed a structural and crystallographic study of both materials, paying attention to the transitions between them. The morphology and crystallography of the laths comprising both microstructures are similar. The main differences were, in general, crystallographic orientation and texture. Whereas the foliated microstructure has a moderate sheet texture, with a defined 001 maximum, the chalk has a much weaker sheet texture, with a defined 011 maximum. This is striking because of the much more disorganized aspect of the chalk. We hypothesize that part of the unanticipated order is inherited from the foliated microstructure by means of, possibly, [Formula: see text] twinning. Growth line distribution suggests that during chalk formation, the mantle separates from the previous shell several times faster than for the foliated material. A shortage of structural material causes the chalk to become highly porous and allows crystals to reorient at a high angle to the mantle surface, with which they continue to keep contact. In conclusion, both materials are structurally similar and the differences in orientation and aspect simply result from differences in growth conditions.

Entropy, materials, and posterity

USGS Publications Warehouse

Cloud, P.

1977-01-01

Materials and energy are the interdependent feedstocks of economic systems, and thermodynamics is their moderator. It costs energy to transform the dispersed minerals of Earth's crust into ordered materials and structures. And it costs materials to collect and focus the energy to perform work - be it from solar, fossil fuel, nuclear, or other sources. The greater the dispersal of minerals sought, the more energy is required to collect them into ordered states. But available energy can be used once only. And the ordered materials of industrial economies become disordered with time. They may be partially reordered and recycled, but only at further costs in energy. Available energy everywhere degrades to bound states and order to disorder - for though entropy may be juggled it always increases. Yet industry is utterly dependent on low entropy states of matter and energy, while decreasing grades of ore require ever higher inputs of energy to convert them to metals, with ever increasing growth both of entropy and environmental hazard. Except as we may prize a thing for its intrinsic qualities - beauty, leisure, love, or gold - low-entropy is the only thing of real value. It is worth whatever the market will bear, and it becomes more valuable as entropy increases. It would be foolish of suppliers to sell it more cheaply or in larger amounts than their own enjoyment of life requires, whatever form it may take. For this reason, and because of physical constraints on the availability of all low-entropy states, the recent energy crises is only the first of a sequence of crises to be expected in energy and materials as long as current trends continue. The apportioning of low-entropy states in a modern industrial society is achieved more or less according to the theory of competitive markets. But the rational powers of this theory suffer as the world grows increasingly polarized into rich, over-industrialized nations with diminishing resource bases and poor, supplier nations with little industry. The theory also discounts posterity, the more so as population density and percapita rates of consumption continue to grow. A new social, economic, and ecologic norm that leads to population control, conservation, and an apportionment of low-entropy states across the generations is needed to assure to posterity the options that properly belong to it as an important but voiceless constituency of the collectivity we call mankind. ?? 1977 Ferdinand Enke Verlag Stuttgart.

Environmental impact of engineered carbon nanoparticles: from releases to effects on the aquatic biota.

PubMed

Mottier, Antoine; Mouchet, Florence; Pinelli, Éric; Gauthier, Laury; Flahaut, Emmanuel

2017-08-01

Nano-ecotoxicology is an emerging science which aims to assess the environmental effect of nanotechnologies. The development of this particular aspect of ecotoxicology was made necessary in order to evaluate the potential impact of recently produced and used materials: nanoparticles (NPs). Among all the types of NPs, carbon nanoparticles (CNPs) especially draw attention giving the increasing number of applications and integration into consumer products. However the potential impacts of CNPs in the environment remain poorly known. This review aims to point out the critical issues and aspects that will govern the toxicity of CNPs in the environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

GaAs-based resonant tunneling diode (RTD) epitaxy on Si for highly sensitive strain gauge applications.

PubMed

Li, Jie; Guo, Hao; Liu, Jun; Tang, Jun; Ni, Haiqiao; Shi, Yunbo; Xue, Chenyang; Niu, Zhichuan; Zhang, Wendong; Li, Mifeng; Yu, Ying

2013-05-08

As a highly sensitive strain gauge element, GaAs-based resonant tunneling diode (RTD) has already been applied in microelectromechanical system (MEMS) sensors. Due to poor mechanical properties and high cost, GaAs-based material has been limited in applications as the substrate for MEMS. In this work, we present a method to fabricate the GaAs-based RTD on Si substrate. From the experimental results, it can be concluded that the piezoresistive coefficient achieved with this method reached 3.42 × 10-9 m2/N, which is about an order of magnitude higher than the Si-based semiconductor piezoresistors.

APTES-modified mesoporous silicas as the carriers for poorly water-soluble drug. Modeling of diflunisal adsorption and release

NASA Astrophysics Data System (ADS)

Geszke-Moritz, Małgorzata; Moritz, Michał

2016-04-01

Four mesoporous siliceous materials such as SBA-16, SBA-15, PHTS and MCF functionalized with (3-aminopropyl)triethoxysilane were successfully prepared and applied as the carriers for poorly water-soluble drug diflunisal. Several techniques including nitrogen sorption analysis, XRD, TEM, FTIR and thermogravimetric analysis were employed to characterize mesoporous matrices. Adsorption isotherms were analyzed using Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models. In order to find the best-fit isotherm for each model, both linear and nonlinear regressions were carried out. The equilibrium data were best fitted by the Langmuir isotherm model revealing maximum adsorption capacity of 217.4 mg/g for aminopropyl group-modified SBA-15. The negative values of Gibbs free energy change indicated that the adsorption of diflunisal is a spontaneous process. Weibull release model was employed to describe the dissolution profile of diflunisal. At pH 4.5 all prepared mesoporous matrices exhibited the improvement of drug dissolution kinetics as compared to the dissolution rate of pure diflunisal.

National supply-chain survey of drug manufacturer back orders.

PubMed

Wellman, G S

2001-07-01

The impact of manufacturer back orders on the supply chain for pharmaceuticals in the institutional setting was studied. A questionnaire was distributed during May and June 2000 to 600 institutional pharmacies affiliated with a major national drug and supply group purchasing organization. The instrument included questions on basic institutional demographics, perceptions about the frequency of manufacturer back orders for pharmaceuticals, the quality of communication with manufacturers and wholesalers about back orders, the two most significant back orders that had occurred in the 12 months preceding the survey, and the reasons for and impact of back orders. A total of 170 usable surveys were returned (net response rate, 28.3%). Reported manufacturer back orders included an array of drug classes, including blood products, antimicrobials, antiarrhythmics, benzodiazepine antagonists, thrombolytics, corticosteroids, and antihypertensives. Respondents perceived significant back orders as increasing in frequency. Communication by manufacturers and wholesalers about back orders was reported to be relatively poor. A raw-material shortage was the most common reason given by manufacturers for back orders (36.5%), followed by a regulatory issue (23.2%). In most cases (92%), medical staff members had to be contacted, indicating an interruption in the normal drug distribution process. In over a third of instances, respondents stated that the back order resulted in less optimal therapy. A survey found that manufacturer back orders for pharmaceuticals were increasing in frequency and that information flow within the supply chain was insufficient to meet the needs of end users.

Enhanced photoelectrochemical water splitting of BiVO4 photonic crystal photoanode by decorating with MoS2 nanosheets

NASA Astrophysics Data System (ADS)

Nan, Feng; Cai, Tianyi; Ju, Sheng; Fang, Liang

2018-04-01

Bismuth vanadate (BiVO4) has been considered as one of the promising Photoelectrochemical (PEC) photoanode materials. However, the performances remain poorly rated due to inefficient carrier separation, short carrier diffusion length, and sluggish water oxidation kinetics. Herein, a photoanode consisting of MoS2 nanosheet coating on the three-dimensional ordered BiVO4 inverse opal is fabricated by a facile combination of nanosphere lithography and hydrothermal methods. By taking advantage of the photonic crystal and two-dimensional material, the optimized MoS2/BiVO4 inverse opal photoanode exhibits a 560% improvement of the photocurrent density and threefold enhancement of the incident photon-to-current efficiency than that of the pristine BiVO4 film photoanode. Systematic studies reveal that the excellent PEC activity should be attributed to enhanced light harvesting and charge separation efficiency.

The Research on Integrated Strategy of Supply Chain Information Systems in the Automobile Industry Based on Order-To-Delivery Mode

NASA Astrophysics Data System (ADS)

Li, Ming; Gan, Lianzhen; He, Xuefeng

The automotive industry there are different degrees of impairment of many companies supply chain IT strategy. In this paper, in which the automotive industry supply chain management business cooperation between enterprises loose, poor exchange of information leading to the presence or delays in product customization, supply of raw materials, material control, production planning and control, sales and service and a fast response propose a series of typical problems of scientific and rational supply chain information integration strategy. The strategy through the development system integration platform, improve internal ERP system, implementation of supply chain management and other methods. Put some protection principles in the information process, to ensure the correct implementation of supply chain IT strategy, and ultimately achieve collaborative business development concept and enhance the automotive industry as a whole level of information.

[Multi-causality in nursing work accidents with biological material].

PubMed

Soares, Leticia Gramazio; Sarquis, Leila Maria Mansano; Kirchhof, Ana Lúcia Cardoso; Felli, Vanda Elisa Andres

2013-12-01

In order to analyze the multiple causes of occupational accidents with biological exposure among nursing staff was carried out a descriptive and exploratory research in a medium-sized hospital in the State of Paraná, in the period between January 2008 and January 2009. The population was 26 nursing staff of the medical clinic. Data collection was performed by semi-structured interviews with five of the eight injured in the period and its contents were analyzed by Causes and Effects Diagram. The categories of causes material, organizational, institutional and worker's behavior, showed the inappropriate disposal of sharps, work overload, no use of bio-security standards and poor supervision and training of workers, as factors for the occurrence of these accidents. The adoption of the tool of Causes and Effects Diagram provided an analysis of accidents in its multiple causes, showing the interaction between them.

Scaling-Relation-Based Analysis of Bifunctional Catalysis: The Case for Homogeneous Bimetallic Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersen, Mie; Medford, Andrew J.; Norskov, Jens K.

Here, we present a generic analysis of the implications of energetic scaling relations on the possibilities for bifunctional gains at homogeneous bimetallic alloy catalysts. Such catalysts exhibit a large number of interface sites, where second-order reaction steps can involve intermediates adsorbed at different active sites. Using different types of model reaction schemes, we show that such site-coupling reaction steps can provide bifunctional gains that allow for a bimetallic catalyst composed of two individually poor catalyst materials to approach the activity of the optimal monomaterial catalyst. However, bifunctional gains cannot result in activities higher than the activity peak of the monomaterialmore » volcano curve as long as both sites obey similar scaling relations, as is generally the case for bimetallic catalysts. These scaling-relation-imposed limitations could be overcome by combining different classes of materials such as metals and oxides.« less

Scaling-Relation-Based Analysis of Bifunctional Catalysis: The Case for Homogeneous Bimetallic Alloys

DOE PAGES

Andersen, Mie; Medford, Andrew J.; Norskov, Jens K.; ...

2017-04-14

Here, we present a generic analysis of the implications of energetic scaling relations on the possibilities for bifunctional gains at homogeneous bimetallic alloy catalysts. Such catalysts exhibit a large number of interface sites, where second-order reaction steps can involve intermediates adsorbed at different active sites. Using different types of model reaction schemes, we show that such site-coupling reaction steps can provide bifunctional gains that allow for a bimetallic catalyst composed of two individually poor catalyst materials to approach the activity of the optimal monomaterial catalyst. However, bifunctional gains cannot result in activities higher than the activity peak of the monomaterialmore » volcano curve as long as both sites obey similar scaling relations, as is generally the case for bimetallic catalysts. These scaling-relation-imposed limitations could be overcome by combining different classes of materials such as metals and oxides.« less

Surface passivation of mixed-halide perovskite CsPb(BrxI1-x)3 nanocrystals by selective etching for improved stability.

PubMed

Jing, Qiang; Zhang, Mian; Huang, Xiang; Ren, Xiaoming; Wang, Peng; Lu, Zhenda

2017-06-08

In recent years, there has been an unprecedented rise in the research of halide perovskites because of their important optoelectronic applications, including photovoltaic cells, light-emitting diodes, photodetectors and lasers. The most pressing question concerns the stability of these materials. Here faster degradation and PL quenching are observed at higher iodine content for mixed-halide perovskite CsPb(Br x I 1-x ) 3 nanocrystals, and a simple yet effective method is reported to significantly enhance their stability. After selective etching with acetone, surface iodine is partially etched away to form a bromine-rich surface passivation layer on mixed-halide perovskite nanocrystals. This passivation layer remarkably stabilizes the nanocrystals, making their PL intensity improved by almost three orders of magnitude. It is expected that a similar passivation layer can also be applied to various other kinds of perovskite materials with poor stability issues.

Household item ownership and self-rated health: material and psychosocial explanations

PubMed Central

Pikhart, Hynek; Bobak, Martin; Rose, Richard; Marmot, Michael

2003-01-01

Background There has been an ongoing debate whether the effects of socioeconomic factors on health are due to absolute poverty and material factors or to relative deprivation and psychosocial factors. In the present analyses, we examined the importance for health of material factors, which may have a direct effect on health, and of those that may affect health indirectly, through psychosocial mechanisms. Methods Random national samples of men and women in Hungary (n = 973) and Poland (n = 1141) were interviewed (response rates 58% and 59%, respectively). The subjects reported their self-rated health, socioeconomic circumstances, including ownership of different household items, and perceived control over life. Household items were categorised as "basic needs", "socially oriented", and "luxury". We examined the association between the ownership of different groups of items and self-rated health. Since the lists of household items were different in Hungary and Poland, we conducted parallel identical analyses of the Hungarian and Polish data. Results The overall prevalence of poor or very poor health was 13% in Poland and 25% in Hungary. Education, material deprivation and the number of household items were all associated with poor health in bivariate analyses. All three groups of household items were positively related to self-rated health in age-adjusted analyses. The relation of basic needs items to poor health disappeared after controlling for other socioeconomic variables (mainly material deprivation). The relation of socially oriented and luxury items to poor health, however, persisted in multivariate models. The results were similar in both datasets. Conclusions These data suggest that health is influenced by both material and psychosocial aspects of socioeconomic factors. PMID:14641929

On the relationship between indentation hardness and modulus, and the damage resistance of biological materials.

PubMed

Labonte, David; Lenz, Anne-Kristin; Oyen, Michelle L

2017-07-15

The remarkable mechanical performance of biological materials is based on intricate structure-function relationships. Nanoindentation has become the primary tool for characterising biological materials, as it allows to relate structural changes to variations in mechanical properties on small scales. However, the respective theoretical background and associated interpretation of the parameters measured via indentation derives largely from research on 'traditional' engineering materials such as metals or ceramics. Here, we discuss the functional relevance of indentation hardness in biological materials by presenting a meta-analysis of its relationship with indentation modulus. Across seven orders of magnitude, indentation hardness was directly proportional to indentation modulus. Using a lumped parameter model to deconvolute indentation hardness into components arising from reversible and irreversible deformation, we establish criteria which allow to interpret differences in indentation hardness across or within biological materials. The ratio between hardness and modulus arises as a key parameter, which is related to the ratio between irreversible and reversible deformation during indentation, the material's yield strength, and the resistance to irreversible deformation, a material property which represents the energy required to create a unit volume of purely irreversible deformation. Indentation hardness generally increases upon material dehydration, however to a larger extent than expected from accompanying changes in indentation modulus, indicating that water acts as a 'plasticiser'. A detailed discussion of the role of indentation hardness, modulus and toughness in damage control during sharp or blunt indentation yields comprehensive guidelines for a performance-based ranking of biological materials, and suggests that quasi-plastic deformation is a frequent yet poorly understood damage mode, highlighting an important area of future research. Instrumented indentation is a widespread tool for characterising the mechanical properties of biological materials. Here, we show that the ratio between indentation hardness and modulus is approximately constant in biological materials. A simple elastic-plastic series deformation model is employed to rationalise part of this correlation, and criteria for a meaningful comparison of indentation hardness across biological materials are proposed. The ratio between indentation hardness and modulus emerges as the key parameter characterising the relative amount of irreversible deformation during indentation. Despite their comparatively high hardness to modulus ratio, biological materials are susceptible to quasiplastic deformation, due to their high toughness: quasi-plastic deformation is hence hypothesised to be a frequent yet poorly understood phenomenon, highlighting an important area of future research. Copyright © 2017 Acta Materialia Inc. All rights reserved.

A BRDF statistical model applying to space target materials modeling

NASA Astrophysics Data System (ADS)

Liu, Chenghao; Li, Zhi; Xu, Can; Tian, Qichen

2017-10-01

In order to solve the problem of poor effect in modeling the large density BRDF measured data with five-parameter semi-empirical model, a refined statistical model of BRDF which is suitable for multi-class space target material modeling were proposed. The refined model improved the Torrance-Sparrow model while having the modeling advantages of five-parameter model. Compared with the existing empirical model, the model contains six simple parameters, which can approximate the roughness distribution of the material surface, can approximate the intensity of the Fresnel reflectance phenomenon and the attenuation of the reflected light's brightness with the azimuth angle changes. The model is able to achieve parameter inversion quickly with no extra loss of accuracy. The genetic algorithm was used to invert the parameters of 11 different samples in the space target commonly used materials, and the fitting errors of all materials were below 6%, which were much lower than those of five-parameter model. The effect of the refined model is verified by comparing the fitting results of the three samples at different incident zenith angles in 0° azimuth angle. Finally, the three-dimensional modeling visualizations of these samples in the upper hemisphere space was given, in which the strength of the optical scattering of different materials could be clearly shown. It proved the good describing ability of the refined model at the material characterization as well.

Amorphous Phase Characterization Through X-Ray Diffraction Profile Modeling: Implications for Amorphous Phases in Gale Crater Rocks and Soils

NASA Technical Reports Server (NTRS)

Achilles, C. N.; Downs, G. W.; Downs, R. T.; Morris, R. V.; Rampe, E. B.; Ming, D. W.; Chipera, S. J.; Blake, D. F.; Vaniman, D. T.; Bristow, T. F.;

In Situ X-ray Diffraction Studies of Li(sub x)Mn(sub 2)O(sub 4) Cathode Materials by Synchrotron X-ray Radiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, X. Q.; Sun, X.; Lee, S. J.

In Situ x-ray diffraction studies on Li{sub x}Mn{sub 2}O{sub 4} spinel cathode materials during charge-discharge cycles were carried out by using a synchrotron as x-ray source. Lithium rich (x = 1.03-1.06) spinel materials obtained from two different sources were studied. Three cubic phases with different lattice constants were observed during charge-discharge cycles in all the samples when a Sufficiently low charge-discharge rate (C/10) was used. There are two regions of two-phase coexistence between these three phases, indicating that both phase transitions are first order. The separation of the Bragg peaks representing these three phases varies from sample to sample andmore » also depends on the charge-discharge rate. These results show that the de-intercalation of lithium in lithium-rich spinel cathode materials proceeds through a series of phase transitions from a lithium-rich phase to a lithium-poor phase and finally to a {lambda}-MnO{sub 2} like cubic phase, rather than through a continuous lattice constant contraction in a single phase.« less

Class Act: In Alabama, Students Turn Tires and Bales of Hay into Striking Architecture for the Poor.

ERIC Educational Resources Information Center

Stewart, Doug

2001-01-01

At the Rural Studio--an off-campus program of Auburn University--architectural students use scavenged and donated materials to create innovative houses and other buildings for poor, rural, primarily African American communities. Materials such as hay bales and old tires are recycled to create full-blown modern architecture, which also fulfills…

Probing cation and vacancy ordering in the dry and hydrated yttrium-substituted BaSnO3 perovskite by NMR spectroscopy and first principles calculations: implications for proton mobility.

PubMed

Buannic, Lucienne; Blanc, Frédéric; Middlemiss, Derek S; Grey, Clare P

2012-09-05

Hydrated BaSn(1-x)Y(x)O(3-x/2) is a protonic conductor that, unlike many other related perovskites, shows high conductivity even at high substitution levels. A joint multinuclear NMR spectroscopy and density functional theory (total energy and GIPAW NMR calculations) investigation of BaSn(1-x)Y(x)O(3-x/2) (0.10 ≤ x ≤ 0.50) was performed to investigate cation ordering and the location of the oxygen vacancies in the dry material. The DFT energetics show that Y doping on the Sn site is favored over doping on the Ba site. The (119)Sn chemical shifts are sensitive to the number of neighboring Sn and Y cations, an experimental observation that is supported by the GIPAW calculations and that allows clustering to be monitored: Y substitution on the Sn sublattice is close to random up to x = 0.20, while at higher substitution levels, Y-O-Y linkages are avoided, leading, at x = 0.50, to strict Y-O-Sn alternation of B-site cations. These results are confirmed by the absence of a "Y-O-Y" (17)O resonance and supported by the (17)O NMR shift calculations. Although resonances due to six-coordinate Y cations were observed by (89)Y NMR, the agreement between the experimental and calculated shifts was poor. Five-coordinate Sn and Y sites (i.e., sites next to the vacancy) were observed by (119)Sn and (89)Y NMR, respectively, these sites disappearing on hydration. More five-coordinated Sn than five-coordinated Y sites are seen, even at x = 0.50, which is ascribed to the presence of residual Sn-O-Sn defects in the cation-ordered material and their ability to accommodate O vacancies. High-temperature (119)Sn NMR reveals that the O ions are mobile above 400 °C, oxygen mobility being required to hydrate these materials. The high protonic mobility, even in the high Y-content materials, is ascribed to the Y-O-Sn cation ordering, which prevents proton trapping on the more basic Y-O-Y sites.

Investigation on the Factors Influencing Construction Time and Cost Overrun for High-Rise Building Projects In Penang

NASA Astrophysics Data System (ADS)

Nor Haslinda, A.; Xian, T. Wei; Norfarahayu, K.; Muhamad Hanafi, R.; Fikri, H. Muhammad

2018-04-01

Time and cost overruns have become one prominent issue for most construction projects around the world. Project costing and timeframe extension had been causing a lot of wastage and loss of opportunity for many parties involved. Therefore, this research was carried out to investigate the factors influencing time and cost overruns for high-rise construction projects in Penang, Malaysia. A set of questionnaires survey was distributed to the project managers who had been or currently involved in the high-rise building projects in Penang to get their input and perceptions for each factor identified as well as its frequency of occurrence. In order to rank all the factors gathered, the mean index of the most distinguishing factors and its frequency of occurrence were multiplied to get the severity index. The results revealed that for time overrun, the most predominant causes were due to design changes, inadequate planning and scheduling and poor labor productivity. Meanwhile, the predominant causes of cost overrun were poor pre-construction budget and material cost planning, inaccurate quantity take-off and materials cost increased by inflation. The significance of establishing the issues related to time and cost overruns for the high-rise building construction project is to provide a greater insight and understanding on the causes of delays, particularly among the main project players: contractors, client, and consultants.

The effect of functional forms of nitrogen on fuel-NOx emissions.

PubMed

Zhang, Linghui; Su, Dagen; Zhong, Mingfeng

2015-01-01

This work explores the effects of different nitrogen functional forms on fuel-NOx emissions at 900 °C. The majority of tests are performed with an excess air coefficient of 1.4. Fuel-NOx is detected by measuring N-(1-naphthyl) ethylenediamine dihydrochloride (C₁₂H₁₆Cl₂N₂) via spectrophotometry. The different functional forms of nitrogen in the raw materials are identified by using X-ray photoelectron spectroscopy (XPS). A reliable density functional theory (DFT) method at the B3LYP/6-311++G** level is employed to investigate the reaction pathways of all functional forms of nitrogen during combustion. The results indicate that the functional forms of nitrogen influence the formation of nitrogen oxides. While under the same experimental conditions, fuel-NOx emissions increase by using less activation energy and nitrogen-containing groups with poor thermal stability. It is determined that fuel-NOx emissions vary in the following order: glycine > pyrrole > pyridine > methylenedi-p-phenylene diisocyanate (MDI). Glycine is the chain structure of amino acids in waste-leather and has low activation energy and poor thermal stability. With these properties, it is noted that glycine produces the most fuel-NOx in all of the raw materials studied. More pyrrole than pyridine in coal lead to high yields of fuel-NOx. The lowest yields of fuel-NO x are obtained using polyurethanes in waste-PU.

Synthesis and characterization of new composite materials based on poly(methacrylic acid) and hydroxyapatite with applications in dentistry.

PubMed

Cucuruz, Andrei Tiberiu; Andronescu, Ecaterina; Ficai, Anton; Ilie, Andreia; Iordache, Florin

2016-08-30

The use of methacrylic acid (MAA) in medicine was poorly investigated in the past but can be of great importance because the incorporation of hydroxyapatite (HA) can lead to new composite materials with good properties due to the strong electrostatic interactions between carboxylate groups of polymer and Ca(2+) ions from HA. The scope of this study was to determine the potential of using composite materials based on poly(methacrylic acid) (PMAA) and hydroxyapatite in dentistry. Two routes of synthesis were taken into account: i) HA was synthesised in situ and ii) commercial HA was used. Fourier transform infrared spectroscopy and X-ray diffraction were used for compositional assessments. Scanning electron microscopy was performed to determine the morphology and differential thermal analysis (DTA) coupled with thermogravimetric analysis (TG) was used to study the thermal behaviour and to observe quantitative changes. In-vitro tests were also performed in order to evaluate the biocompatibility of both PMAA/HA composites by monitoring the development potential of human endothelial cells using MTT assay and fluorescent microscopy. Copyright © 2016 Elsevier B.V. All rights reserved.

Health System Competency for Maternal Health Services in Balasore District and Jaleswar Block, Balasore, Odisha, India: An Assessment

PubMed Central

Samal, Janmejaya

2016-01-01

Introduction A competent health system is of paramount importance in delivering the desired health services in a particular community. Aim The broad objective of this study was to assess the health system competency for the maternal health services in Balasore District and Jaleswar block of Balasore district, Odisha, India. Materials and Methods A mixed method approach was adopted in order to understand the health system competency for maternal health services in the study area. Results There was poor accessibility through road, poor electricity connection and piped water for the health care centers in the district. Even, existing Primary Health Centres (PHCs) lack ECG and X-Ray machines for proper diagnostic services which jeopardize the catering of health services. Community Health Centres (CHC) lack basic diagnostic and ambulance services making the tribal pockets inaccessible. The tribal dominated Jaleswar block shows poor performance in terms of total registered Antenatal Checkups (ANC) (only 77%). A gradual decrease in the rate of ANC, from first to fourthcheckup, was observed in the district. Conclusion Lack of public health infrastructure in general and non-compliance to Indian Public Health Standards (IPHS) in particular, affect the health of tribal women resulting in lack of interest in availing the institutional delivery services and other pertinent maternal health services. PMID:27656464

Micro-structure and motion of two-dimensional dense short spherocylinder liquids

NASA Astrophysics Data System (ADS)

Wang, Wen; Lin, Jyun-Ting; Su, Yen-Shuo; I, Lin

2018-03-01

We numerically investigate the micro-structure and motion of 2D liquids composed of dense short spherocylinders, by reducing the shape aspect ratio from 3. It is found that reducing shape aspect ratio from 3 causes a smooth transition from heterogeneous structures composed of crystalline ordered domains with good tetratic alignment order to those with good hexagonal bond-orientational order at an aspect ratio equaling 1.35. In the intermediate regime, both structural orders are strongly deteriorated, and the translational hopping rate reaches a maximum due to the poor particle interlocking of the disordered structure. Shortening rod length allows easier rotation, induces monotonic increase of rotational hopping rates, and resumes the separation of rotational and translational hopping time scales at the small aspect ratio end, after the crossover of their rates in the intermediate regime. At the large shape aspect ratio end, the poor local tetratic order has the same positive effects on facilitating local rotational and translational hopping. In contrast, at the small shape aspect ratio end, the poor local bond orientational order has the opposite effects on facilitating local rotational and translational hopping.

3D Graphene-Infused Polyimide with Enhanced Electrothermal Performance for Long-Term Flexible Space Applications.

PubMed

Loeblein, Manuela; Bolker, Asaf; Tsang, Siu Hon; Atar, Nurit; Uzan-Saguy, Cecile; Verker, Ronen; Gouzman, Irina; Grossman, Eitan; Teo, Edwin Hang Tong

2015-12-22

Polyimides (PIs) have been praised for their high thermal stability, high modulus of elasticity and tensile strength, ease of fabrication, and moldability. They are currently the standard choice for both substrates for flexible electronics and space shielding, as they render high temperature and UV stability and toughness. However, their poor thermal conductivity and completely electrically insulating characteristics have caused other limitations, such as thermal management challenges for flexible high-power electronics and spacecraft electrostatic charging. In order to target these issues, a hybrid of PI with 3D-graphene (3D-C), 3D-C/PI, is developed here. This composite renders extraordinary enhancements of thermal conductivity (one order of magnitude) and electrical conductivity (10 orders of magnitude). It withstands and keeps a stable performance throughout various bending and thermal cycles, as well as the oxidative and aggressive environment of ground-based, simulated space environments. This makes this new hybrid film a suitable material for flexible space applications. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Protein nanoparticles are nontoxic, tuneable cell stressors.

PubMed

de Pinho Favaro, Marianna Teixeira; Sánchez-García, Laura; Sánchez-Chardi, Alejandro; Roldán, Mónica; Unzueta, Ugutz; Serna, Naroa; Cano-Garrido, Olivia; Azzoni, Adriano Rodrigues; Ferrer-Miralles, Neus; Villaverde, Antonio; Vázquez, Esther

2018-02-01

Nanoparticle-cell interactions can promote cell toxicity and stimulate particular behavioral patterns, but cell responses to protein nanomaterials have been poorly studied. By repositioning oligomerization domains in a simple, modular self-assembling protein platform, we have generated closely related but distinguishable homomeric nanoparticles. Composed by building blocks with modular domains arranged in different order, they share amino acid composition. These materials, once exposed to cultured cells, are differentially internalized in absence of toxicity and trigger distinctive cell adaptive responses, monitored by the emission of tubular filopodia and enhanced drug sensitivity. The capability to rapidly modulate such cell responses by conventional protein engineering reveals protein nanoparticles as tuneable, versatile and potent cell stressors for cell-targeted conditioning.

Space Weathering of Itokawa Particles: Implications for Regolith Evolution

NASA Technical Reports Server (NTRS)

Berger, Eve L.; Keller, Lindsay P.

2015-01-01

Space weathering processes such as solar wind irradiation and micrometeorite impacts are known to alter the the properties of regolith materials exposed on airless bodies. The rates of space weathering processes however, are poorly constrained for asteroid regoliths, with recent estimates ranging over many orders of magnitude. The return of surface samples by JAXA's Hayabusa mission to asteroid 25143 Itokawa, and their laboratory analysis provides "ground truth" to anchor the timescales for space weathering processes on airless bodies. Here, we use the effects of solar wind irradiation and the accumulation of solar flare tracks recorded in Itokawa grains to constrain the rates of space weathering and yield information about regolith dynamics on these timescales.

GaAs-based resonant tunneling diode (RTD) epitaxy on Si for highly sensitive strain gauge applications

PubMed Central

2013-01-01

As a highly sensitive strain gauge element, GaAs-based resonant tunneling diode (RTD) has already been applied in microelectromechanical system (MEMS) sensors. Due to poor mechanical properties and high cost, GaAs-based material has been limited in applications as the substrate for MEMS. In this work, we present a method to fabricate the GaAs-based RTD on Si substrate. From the experimental results, it can be concluded that the piezoresistive coefficient achieved with this method reached 3.42 × 10−9 m2/N, which is about an order of magnitude higher than the Si-based semiconductor piezoresistors. PMID:23651496

Repair welding of cast iron coated electrodes

NASA Astrophysics Data System (ADS)

Żuk, M.; Górka, J.; Dojka, R.; Czupryński, A.

2017-08-01

Welding cast iron is a complex production procedure. Repair welding was used to repair damaged or poorly made castings. This is due to a tendency to cracking of the material during welding as well as after it. Welding cast iron can be carried out on hot or on cold. Hot welding requires high heat material and the use of welding material in the form of cast iron. In the case of cold welding, it is possible to use different materials. Mostly used filler metals are nickel and copper based. The work shows the course of research concerning repairmen of ductile iron with arc welding method. For the reparation process four types of ESAB company coated electrodes dedicated for cast iron were used with diameter 3.2 and 4 mm: ES 18-8-6B (4mm), EB 150 (4mm), OK NiCl, EŻM. In the cast iron examined during the testing grooves were made using plasma methods, in order to simulate the removed casting flaws. Then the welding process with coated electrodes was executed. The process utilized low welding current row of 100A, so there would only be a small amount of heat delivered to the heat affected zone (HAZ). Short stitches were made, after welding it was hammered, in order to remove stresses. After the repair welding the part of studies commenced which purpose was finding surface defects using visual testing (VT) and penetration testing (PT). In the second part, a series of macro and microscopic studies were executed witch the purpose of disclosuring the structure. Then the hardness tests for welds cross sections were performed. An important aspect of welding cast iron is the colour of the padding weld after welding, more precisely the difference between the base material and padding weld, the use of different materials extra gives the extra ability to select the best variant. The research of four types of coated electrode was executed, based on the demands the best option in terms of aesthetic, strength and hardness.

In vitro and in vivo evaluation of ordered mesoporous silica as a novel adsorbent in liquisolid formulation

PubMed Central

Chen, Bao; Wang, Zhouhua; Quan, Guilan; Peng, Xinsheng; Pan, Xin; Wang, Rongchang; Xu, Yuehong; Li, Ge; Wu, Chuanbin

2012-01-01

Background A liquisolid technique has been reported to be a new approach to improve the release of poorly water-soluble drugs for oral administration. However, an apparent limitation of this technique is the formulation of a high dose because a large amount of liquid vehicle is needed, which finally results in a low-dose liquisolid formulation. Silica as an absorbent has been used extensively in liquisolid formulations. Although nanoparticle silica can be prepared and used to improve liquid adsorption capacity, loading a high dose of drug into a liquisolid is still a challenge. With the aim of improving adsorption capacity and accordingly achieving high drug loading, ordered mesoporous silica with a high surface area and narrow pore size distribution was synthesized and used in a liquisolid formulation. Methods Ordered mesoporous silica was synthesized and its particle size and morphology were tailored by controlling the concentration of cetyltrimethyl ammonium bromide. The ordered mesoporous silica synthesized was characterized by transmission electron microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy, small-angle x-ray diffraction, wide angle x-ray diffraction, and nitrogen adsorption-desorption measurements. The liquid adsorption capacity of ordered mesoporous silica was subsequently compared with that of conventional silica materials using PEG400 as the model liquid. Carbamazepine was chosen as a model drug to prepare the liquisolid formulation, with ordered mesoporous silica as the adsorbent material. The preparation was evaluated and compared with commercially available fast-release carbamazepine tablets in vitro and in vivo. Results Characterization of the ordered mesoporous silica synthesized in this study indicated a huge Brunauer–Emmett–Teller surface area (1030 m2/g), an ordered mesoporous structure with a pore size of 2.8 nm, and high adsorption capacity for liquid compared with conventional silica. Compared with fast-release commercial carbamazepine tablets, drug release from the liquisolid capsules was greatly improved, and the bioavailability of the liquisolid preparation was enhanced by 182.7%. Conclusion Ordered mesoporous silica is a potentially attractive adsorbent which may lead to a new approach for development of liquisolid products. PMID:22275835

Fluids Density Functional Theory of Salt-Doped Block Copolymers

NASA Astrophysics Data System (ADS)

Brown, Jonathan R.; Hall, Lisa M.

Block copolymers have attracted a great deal of recent interest as potential non-flammable, solid-state, electrolyte materials for batteries or other charge carrying applications. The microphase separation in block copolymers combines the properties of a conductive (though mechanically soft) polymer with a mechanically robust (though non-conductive) polymer. We use fluids density functional theory (fDFT) to study the phase behavior of salt-doped block copolymers. Because the salt prefers to preferentially solvate into the conductive phase, salt doping effectively enhances the segregation strength between the two polymer types. We consider the effects of this preferential solvation and of charge correlations by separately modeling the ion-rich phase, without bonding, using the Ornstein-Zernike equation and the hypernetted-chain closure. We use the correlations from this subsystem in the inhomogeneous fDFT calculations. Initial addition of salt increases the domain spacing and sharpens the interfacial region, but for high salt loadings the interface can broaden. Addition of salt can also drive a system with a low copolymer segregation strength to order by first passing through a two phase regime with a salt-rich ordered phase and a salt-poor disordered phase. This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Award Number DE-SC0014209.

The use of silicone based adhesives to encapsulate manganin gauges for high stress experiments

NASA Astrophysics Data System (ADS)

Be'Ery, Ilan; Rosenberg, Zvi

2007-06-01

The use of commercial manganin stress gauges has been limited to stresses in the range of 0-20 GPa due to the short-circuiting of their encapsulating materials (epoxy, Kapton) at higher pressures. Researchers at Lawrence Livermore overcome this difficulty by embedding their gauges in Teflon sheets and measured shock pressures as high as 40 GPa. The fact that Teflon can keep its resistivity at high pressures is attributed to the lack of benzene rings in its structure. On the other hand, Teflon is difficult to work with as an encapsulating material because of its poor adhesive properties. In order to overcome this difficulty we encapsulated our foils in between two tapes of Teflon which have a silicone adhesive glued to it. These are 50 μm thick commercial tapes (manufactured by 3M, type #60) which have a 50 μm thick silicone adhesive (PSA -- pressure sensitive adhesive) on them. This adhesive is easy to work with, has no benzene rings in its structure and has a lower carbon content, compared to other adhesives. Several experiments were conducted in order to directly measure the resistivity of these tapes at high pressures, as well as using them to encapsulate our manganin foils for high pressure studies.

Alloy and composition dependence of hydrogen embrittlement susceptibility in high-strength steel fasteners

NASA Astrophysics Data System (ADS)

Brahimi, S. V.; Yue, S.; Sriraman, K. R.

2017-06-01

High-strength steel fasteners characterized by tensile strengths above 1100 MPa are often used in critical applications where a failure can have catastrophic consequences. Preventing hydrogen embrittlement (HE) failure is a fundamental concern implicating the entire fastener supply chain. Research is typically conducted under idealized conditions that cannot be translated into know-how prescribed in fastener industry standards and practices. Additionally, inconsistencies and even contradictions in fastener industry standards have led to much confusion and many preventable or misdiagnosed fastener failures. HE susceptibility is a function of the material condition, which is comprehensively described by the metallurgical and mechanical properties. Material strength has a first-order effect on HE susceptibility, which increases significantly above 1200 MPa and is characterized by a ductile-brittle transition. For a given concentration of hydrogen and at equal strength, the critical strength above which the ductile-brittle transition begins can vary due to second-order effects of chemistry, tempering temperature and sub-microstructure. Additionally, non-homogeneity of the metallurgical structure resulting from poorly controlled heat treatment, impurities and non-metallic inclusions can increase HE susceptibility of steel in ways that are measurable but unpredictable. Below 1200 MPa, non-conforming quality is often the root cause of real-life failures. This article is part of the themed issue 'The challenges of hydrogen and metals'.

Poverty and transitions in health in later life.

PubMed

Adena, Maja; Myck, Michal

2014-09-01

Using a sample of Europeans aged 50+ from 12 countries in the Survey of Health, Ageing and Retirement in Europe (SHARE), we analyse the role of poor material conditions as a determinant of changes in health over a four- to five-year period. We find that poverty defined with respect to relative income has no effect on changes in health. However, broader measures of poor material conditions, such as subjective poverty or low wealth, significantly increase the probability of transition to poor health among the healthy and reduce the chance of recovery from poor health over the time interval analysed. In addition to this, the subjective measure of poverty has a significant effect on mortality, increasing it by 65% among men and by 68% among those aged 50-64. Material conditions affect health among older people. We suggest that if attempts to reduce poverty in later life and corresponding policy targets are to focus on the relevant measures, they should take into account broader definitions of poverty than those based only on relative incomes. Copyright © 2014 Elsevier Ltd. All rights reserved.

Assessment of health service delivery capacities, health providers' knowledge and practices related to type 2 diabetes care in Kinshasa primary healthcare network facilities, Democratic Republic of the Congo.

PubMed

Kapongo, Remy Y; Lulebo, Aimée M; Mafuta, Eric M; Mutombo, Paulin B; Dimbelolo, Jean Claude M; Bieleli, Isidore E

2015-01-22

Democratic Republic of the Congo (DRC) is experiencing an increase in the morbi-mortality related to Non Communicable Diseases (NCD). The reform of DRC health system, based on Health District model, is needed in order to tackle this public issue. This article used 2006 International Diabetes Federation (IDF)'s guidelines to assess the capacities of health facilities belonging to Kinshasa Primary Health Care Network (KPHCN) in terms of equipments, as well as the knowledge, and the practice of their health providers related to type 2 diabetes care. A multicentric cross-sectional study was carried in 18 Health Facilities (HF) of KPHCN in charge of the follow-up of diabetic patients. The presence of IDF recommended materials and equipment was checked and 28 health providers were interviewed about their theoretical knowledge about patients' management and therapeutic objectives during recommended visits. Chi square test or Fisher exact test was used to compare proportions and the Student t-test to compare means. The integration of NCD healthcare in the KPHC network is feasible. The majority of HF possessed IDF recommended materials except for the clinical practice guidelines, urinary test strips, and monofilament, available in only one, two and four HF, respectively. KPHCN referral facilities had required materials for biochemical analyses, the ECG and for the fundus oculi test. Patients' management is characterized by a lack of attention on the impairment of renal function during the first visits and a poor respect of recommended practices during quarterly and annual visits. A poor knowledge of the reduction of cardiovascular risk factors-related therapeutic objectives has been also reported. The capacities, knowledge, and practice of T2D care were poor among HF of KPHCN. The lack of equipment and training of healthcare professionals should be supplied even to those who are not medical doctors. Special attention must to be put on the clinical practice guidelines formulation and sensitization and on supervision.

7 CFR 52.3184 - Grades of dried prunes.

Code of Federal Regulations, 2013 CFR

2013-01-01

... be affected by: Off-color. End cracks. 1 Skin or flesh Mold. Poor texture. Skin or flesh damage. 2..., by weight, may be affected by: Off-color. Poor texture. Mold. Decay. Poor texture. End cracks. Dirt. End cracks. Skin or flesh Foreign material. Skin or flesh damage. 2 damage. 2 Fermentation. Insect...

7 CFR 52.3184 - Grades of dried prunes.

Code of Federal Regulations, 2014 CFR

2014-01-01

... be affected by: Off-color. End cracks. 1 Skin or flesh Mold. Poor texture. Skin or flesh damage. 2..., by weight, may be affected by: Off-color. Poor texture. Mold. Decay. Poor texture. End cracks. Dirt. End cracks. Skin or flesh Foreign material. Skin or flesh damage. 2 damage. 2 Fermentation. Insect...

A Novel Synthesis Routine for Woodwardite and Its Affinity towards Light (La, Ce, Nd) and Heavy (Gd and Y) Rare Earth Elements.

PubMed

Consani, Sirio; Balić-Žunić, Tonci; Cardinale, Anna Maria; Sgroi, Walter; Giuli, Gabriele; Carbone, Cristina

2018-01-14

A synthetic Cu-Al-SO₄ layered double hydroxide (LDH), analogue to the mineral woodwardite [Cu 1-x Al x (SO₄) x/2 (OH)₂·nH₂O], with x < 0.5 and n ≤ 3x/2, was synthesised by adding a solution of Cu and Al sulphates to a solution with NaOH. The pH values were kept constant at 8.0 and 10.0 by a continuous addition of NaOH. The material obtained had poor crystallinity, turbostratic structure, and consisted of nanoscopic crystallites. The analyses performed in order to characterise the obtained materials (X-ray diffraction (XRD), thermogravimetry (TG), and Fourier Transform Infra-Red (FTIR) spectroscopy) showed that the Cu-Al-SO₄ LDH is very similar to woodwardite, although it has a smaller layer spacing, presumably due to a lesser water content than in natural samples. The synthesis was performed by adding light rare earth elements (LREEs) (La, Ce, and Nd) and heavy rare earth elements (HREEs) (Gd and Y) in order to test the affinity of the Cu-Al-SO₄ LDH to the incorporation of REEs. The concentration of rare earth elements (REEs) in the solid fraction was in the range of 3.5-8 wt %. The results showed a good affinity for HREE and Nd, especially for materials synthesised at pH 10.0, whereas the affinities for Ce and La were much lower or non-existent. The thermal decomposition of the REE-doped materials generates a mixture of Cu, Al, and REE oxides, making them interesting as precursors in REE oxide synthesis.

A Novel Synthesis Routine for Woodwardite and Its Affinity towards Light (La, Ce, Nd) and Heavy (Gd and Y) Rare Earth Elements

PubMed Central

Consani, Sirio; Balić-Žunić, Tonci; Cardinale, Anna Maria; Sgroi, Walter; Giuli, Gabriele; Carbone, Cristina

2018-01-01

A synthetic Cu-Al-SO4 layered double hydroxide (LDH), analogue to the mineral woodwardite [Cu1−xAlx(SO4)x/2(OH)2·nH2O], with x < 0.5 and n ≤ 3x/2, was synthesised by adding a solution of Cu and Al sulphates to a solution with NaOH. The pH values were kept constant at 8.0 and 10.0 by a continuous addition of NaOH. The material obtained had poor crystallinity, turbostratic structure, and consisted of nanoscopic crystallites. The analyses performed in order to characterise the obtained materials (X-ray diffraction (XRD), thermogravimetry (TG), and Fourier Transform Infra-Red (FTIR) spectroscopy) showed that the Cu-Al-SO4 LDH is very similar to woodwardite, although it has a smaller layer spacing, presumably due to a lesser water content than in natural samples. The synthesis was performed by adding light rare earth elements (LREEs) (La, Ce, and Nd) and heavy rare earth elements (HREEs) (Gd and Y) in order to test the affinity of the Cu-Al-SO4 LDH to the incorporation of REEs. The concentration of rare earth elements (REEs) in the solid fraction was in the range of 3.5–8 wt %. The results showed a good affinity for HREE and Nd, especially for materials synthesised at pH 10.0, whereas the affinities for Ce and La were much lower or non-existent. The thermal decomposition of the REE-doped materials generates a mixture of Cu, Al, and REE oxides, making them interesting as precursors in REE oxide synthesis. PMID:29342887

Response of pore water Al, Fe and S concentrations to waterlogging in a boreal acid sulphate soil.

PubMed

Virtanen, Seija; Simojoki, Asko; Hartikainen, Helinä; Yli-Halla, Markku

2014-07-01

Environmental hazards caused by acid sulphate (AS) soils are of worldwide concern. Among various mitigation measures, waterlogging has mainly been studied in subtropical and tropical conditions. To assess the environmental relevance of waterlogging as a mitigation option in boreal AS soils, we arranged a 2.5-year experiment with monolithic lysimeters to monitor changes in the soil redox potential, pH and the concentrations of aluminium (Al), iron (Fe) and sulphur (S) in pore water in response to low and high groundwater levels in four AS soil horizons. The monoliths consisted of acidic oxidized B horizons and a reduced C horizon containing sulphidic material. Eight lysimeters were cropped (reed canary grass, Phalaris arundinacea) and two were bare without a crop. Waterlogging was conducive to reduction reactions causing a slight rise in pH, a substantial increase in Fe (Fepw) and a decrease in Al (Alpw) in the pore water. The increase in Fepw was decisively higher in the cropped waterlogged lysimeters than in the bare ones, which was attributable to the microbiologically catalysed reductive dissolution of poorly ordered iron oxides and secondary minerals. In contrast to warmer climates, Fepw concentrations remained high throughout the experiment, indicating that the reduction was poised in the iron range, while sulphate was not reduced to sulphide. Therefore, the precipitation of iron sulphide was negligible in the environment with a low pH and abundant with poorly ordered Fe oxides. Increased Fe in pore water counteracts the positive effects of waterlogging, when water is flushed from fields to watercourses, where re-oxidation of Fe causes acidity and oxygen depletion. However, waterlogging prevented further oxidation of sulphidic materials and decreased Alpw to one-tenth of the initial concentrations, and even to one-hundredth of the levels in the low water table lysimeters. Copyright © 2014 Elsevier B.V. All rights reserved.

Transition from poor ductility to room-temperature superplasticity in a nanostructured aluminum alloy.

PubMed

Edalati, Kaveh; Horita, Zenji; Valiev, Ruslan Z

2018-04-30

Recent developments of nanostructured materials with grain sizes in the nanometer to submicrometer range have provided ground for numerous functional properties and new applications. However, in terms of mechanical properties, bulk nanostructured materials typically show poor ductility despite their high strength, which limits their use for structural applications. The present article shows that the poor ductility of nanostructured alloys can be changed to room-temperature superplastisity by a transition in the deformation mechanism from dislocation activity to grain-boundary sliding. We report the first observation of room-temperature superplasticity (over 400% tensile elongations) in a nanostructured Al alloy by enhanced grain-boundary sliding. The room-temperature grain-boundary sliding and superplasticity was realized by engineering the Zn segregation along the Al/Al boundaries through severe plastic deformation. This work introduces a new boundary-based strategy to improve the mechanical properties of nanostructured materials for structural applications, where high deformability is a requirement.

Compression Molding of Composite of Recycled HDPE and Recycled Tire Particles

NASA Technical Reports Server (NTRS)

Liu, Ping; Waskom, Tommy L.; Chen, Zhengyu; Li, Yanze; Peng, Linda

1996-01-01

Plastic and rubber recycling is an effective means of reducing solid waste to the environment and preserving natural resources. A project aimed at developing a new composite material from recycled high density polyethylene (HDPE) and recycled rubber is currently being conducted at Eastern Illinois University. The recycled plastic pellets with recycled rubber particles are extruded into some HDPE/rubber composite strands. The strand can be further cut into pellets that can be used to fabricate other material forms or products. This experiment was inspired by the above-mentioned research activity. In order to measure Durometer hardness of the extruded composite, a specimen with relatively large dimensions was needed. Thus, compression molding was used to form a cylindrical specimen of 1 in. diameter and 1 in. thickness. The initial poor quality of the molded specimen prompted a need to optimize the processing parameters such as temperature, holding time, and pressure. Design of experiment (DOE) was used to obtain optimum combination of the parameters.

Cost Effective Instrumentation for Developing Autonomous Groundwater Monitoring Networks

NASA Astrophysics Data System (ADS)

Viti, T. M.; Garmire, D. G.

2017-12-01

Despite a relatively poor understanding of Hawaiian groundwater systems, the State of Hawaii depends almost exclusively on groundwater for its public water supply. Ike Wai, an NSF funded project (EPSCoR Program Award OIA #1557349) at the University of Hawaii, aims to develop new groundwater models for Hawaii's aquifers, including water quality and transport processes. To better understand aquifer properties such as capacity and hydraulic conductivity, we are developing well-monitoring instruments that can autonomously record water parameters such as conductivity, temperature, and hydraulic head level, with sampling frequencies on the order of minutes. We are currently exploring novel methods and materials for solving classical design problems, such as applying dielectric spectroscopy techniques for measuring salinity, and using recycled materials for producing custom cable assemblies. System components are fabricated in house using rapid prototyping (e.g. 3D printing, circuit board milling, and laser cutting), and traditional manufacturing techniques. This approach allows us to produce custom components while minimizing development cost, and maximizing flexibility in the overall system's design.

Observations of liquid-liquid phase separation in several types of secondary organic materials free of inorganic salts

NASA Astrophysics Data System (ADS)

Song, M.; Liu, P.; Martin, S. T.; Bertram, A. K.; Ham, S.

2016-12-01

Particles consisting of secondary organic materials (SOMs) are ubiquitous in the atmosphere. In order to predict the role of these particles in climate, visibility, and atmospheric chemistry, knowledge of the phase states of the particles is required. However, the phase states of the SOMs are still poorly understood. Herein we focused on liquid-liquid phase separation in different types of SOM particles free of inorganic salts produced by the ozonolysis of β-caryophyllene, ozonolysis of limonene, photo-oxidation of isoprene, and photo-oxidation of toluene. Liquid-liquid phase separation was investigated using optical microscopy and SOM particle mass concentrations ranging from 15 µg·m-3 to 7000 µg·m-3. During humidity cycles, liquid-liquid phase separation was observed in β-caryophyllene-derived SOM and limonene-derived SOM particles while no liquid-liquid phase separation was observed in isoprene-derived SOM and toluene-derived SOM particles. Results from the studies will be presented.

First-Principles Materials Design of High-Performing Bulk Photovoltaics with the Li Nb O 3 Structure

DOE PAGES

Young, Steve M.; Zheng, Fan; Rappe, Andrew M.

2015-11-18

Here, the bulk photovoltaic effect is a long-known but poorly understood phenomenon. Recently, however, the multiferroic bismuth ferrite has been observed to produce strong photovoltaic response to visible light, suggesting that the effect has been underexploited as well. Here we present three polar oxides in the LiNbOmore » $$_3$$ structure that we predict to have band gaps in the 1-2 eV range and very high bulk photovoltaic response: PbNiO$$_3$$, Mg$$_{1/2}$$Zn$$_{1/2}$$PbO$$_3$$, and LiBiO$$_3$$. All three have band gaps determined by cations with $$d^{10}s^0$$ electronic configurations, leading to conduction bands composed of cation $s$-orbitals and O $p$-orbitals. This both dramatically lowers the band gap and increases the bulk photovoltaic response by as much as an order of magnitude over previous materials, demonstrating the potential for high-performing bulk photovoltaics.« less

Dual Neutral Particle Beam Interrogation of Intermodal Shipping Containers for Special Nuclear Material

NASA Astrophysics Data System (ADS)

Keith, Rodney Lyman

Intermodal shipping containers entering the United States provide an avenue to smuggle unsecured or stolen special nuclear material (SNM). The only direct method fielded to indicate the presence of SNM is by passive photon/neutron radiation detection. Active interrogation using neutral particle beams to induce fission in SNM is a method under consideration. One by-product of fission is the creation of fragments that undergo radioactive decay over a time period on the order of tens of seconds after the initial event. The "delayed" gamma-rays emitted from these fragments over this period are considered a hallmark for the presence of SNM. A fundamental model is developed using homogenized cargos with a SNM target embedded at the center and computationally interrogated using simultaneous neutron and photon beams. Findings from analysis of the delayed gamma emissions from these experiments are intended to mitigate the effects of poor quality information about the composition and disposition of suspect cargo before examination in an active interrogation portal.

Structural energy dissipation in extreme loading events using shape memory alloys

NASA Astrophysics Data System (ADS)

Angioni, Stefano L.

It is well known that composite materials have a poor resistance to the damage caused by the impact of foreign objects on their outer surface. There are various methods for improving the impact damage tolerance of composite materials, such as: fibre toughening, matrix toughening, interface toughening, through the thickness reinforcements and selective interlayers and hybrids. Hybrid composites with improved impact resistance would be particularly useful in military and commercial civil applications. Hybridizing composites using shape memory alloys (SMAs) is one solution since SMA materials can absorb the energy of impact through superelastic deformation or recovery stress reducing the effects of the impact on the composite structure. The SMA material may be embedded in the hybrid composites (SMAHC) in many different forms and also the characteristics of the fibre reinforcements may vary, such as SMA wires in unidirectional laminates or SMA foils in unidirectional laminates only to cite two examples. Recently SMA fibres have been embedded in 2-D woven composites. As part of this work, the existing theoretical models for woven composites have been extended to the case of woven SMAHC using a multiscale methodology in order to predict the mechanical properties and failure behaviour of SMAHC plates. Also several parts of the model have been coded in MATLAB and validated against results extracted from the literature, showing good correlation..

Shellac/nanoparticles dispersions as protective materials for wood

NASA Astrophysics Data System (ADS)

Weththimuni, Maduka L.; Capsoni, Doretta; Malagodi, Marco; Milanese, Chiara; Licchelli, Maurizio

2016-12-01

Wood is a natural material that finds numerous and widespread applications, but is subject to different decay processes. Surface coating is the most common method used to protect wood against deterioration and to improve and stabilize its distinctive appearance. Shellac is a natural resin that has been widely used as a protective material for wooden artefacts (e.g. furniture, musical instruments), due to its excellent properties. Nevertheless, diffusion of shellac-based varnishes has significantly declined during the last decades, because of some limitations such as the softness of the coating, photo-degradation, and sensitivity to alcoholic solvents and to pH variations. In the present study, different inorganic nanoparticles were dispersed into dewaxed natural shellac and the resulting materials were investigated even after application on wood specimens in order to assess variations of the coating properties. Analyses performed by a variety of experimental techniques have shown that dispersed nanoparticles do not significantly affect some distinctive and desirable features of the shellac varnish such as chromatic aspect, film-forming ability, water repellence, and adhesion. On the other hand, the obtained results suggested that some weak points of the coating, such as low hardness and poor resistance to UV-induced ageing, can be improved by adding ZrO2 and ZnO nanoparticles, respectively.

Nanostructured Materials Utilized in Biopolymer-based Plastics for Food Packaging Applications.

PubMed

Ghanbarzadeh, Babak; Oleyaei, Seyed Amir; Almasi, Hadi

2015-01-01

Most materials currently used for food packaging are nondegradable, generating environmental problems. Several biopolymers have been exploited to develop materials for ecofriendly food packaging. However, the use of biopolymers has been limited because of their usually poor mechanical and barrier properties, which may be improved by adding reinforcing compounds (fillers), forming composites. Most reinforced materials present poor matrix-filler interactions, which tend to improve with decreasing filler dimensions. The use of fillers with at least one nanoscale dimension (nanoparticles) produces nanocomposites. Nanoparticles have proportionally larger surface area than their microscale counterparts, which favors the filler-matrix interactions and the performance of the resulting material. Besides nanoreinforcements, nanoparticles can have other functions when added to a polymer, such as antimicrobial activity, etc. in this review paper, the structure and properties of main kinds of nanostructured materials which have been studied to use as nanofiller in biopolymer matrices are overviewed, as well as their effects and applications.

A brief understanding of process optimisation in microwave-assisted extraction of botanical materials: options and opportunities with chemometric tools.

PubMed

Das, Anup Kumar; Mandal, Vivekananda; Mandal, Subhash C

2014-01-01

Extraction forms the very basic step in research on natural products for drug discovery. A poorly optimised and planned extraction methodology can jeopardise the entire mission. To provide a vivid picture of different chemometric tools and planning for process optimisation and method development in extraction of botanical material, with emphasis on microwave-assisted extraction (MAE) of botanical material. A review of studies involving the application of chemometric tools in combination with MAE of botanical materials was undertaken in order to discover what the significant extraction factors were. Optimising a response by fine-tuning those factors, experimental design or statistical design of experiment (DoE), which is a core area of study in chemometrics, was then used for statistical analysis and interpretations. In this review a brief explanation of the different aspects and methodologies related to MAE of botanical materials that were subjected to experimental design, along with some general chemometric tools and the steps involved in the practice of MAE, are presented. A detailed study on various factors and responses involved in the optimisation is also presented. This article will assist in obtaining a better insight into the chemometric strategies of process optimisation and method development, which will in turn improve the decision-making process in selecting influential extraction parameters. Copyright © 2013 John Wiley & Sons, Ltd.

Ground test article for deployable space structure systems

NASA Technical Reports Server (NTRS)

Malloy, G. D.

1984-01-01

The ground test article fabrication and assembly plan was completed by Santek Engineering, Inc. The plan was reviewed and accepted by Rockwell during an on-site visit to the Santek facility. Raw material and hardware orders were placed by Santek in July. Approximately 98% of the raw materials and 10% of the hardware deliveries have been completed. Several material and hardware substitutions were requested by Santek due to no-bid responses from suppliers or excessive costs for limited quantity items. These substitutions were evaluated and approved by Rockwell Engineering and Material and Process and are being incorporated into the drawing package. Santek started fabrication of detail parts in mid-August. Their current resource utilization is at approximately 50% of the planned eventual commitment and is increasing at a rate commensurate with the fabrication and assembly plan. At this writing, Santek's estimate of completion is 03%. During verification testing of the diagonal member joint, in a program funded by Rockwell discretionary funds, the axial load to unlock the joint was found to increase significantly after a few cycles of operation. This was attributed to galling, poor lubrication, and locking pin geometry. A change of materials, lubricant, and modification of the pin geometry reduced the unlocking load and provided repeatability after 50 cycles of operation. This new design is being implemented into the ground test article.

Clinical Investigation of a New Bulk Fill Composite Resin in the Restoration of Posterior Teeth

ClinicalTrials.gov

2017-09-14

Dental Restoration Failure of Marginal Integrity; Dental Caries; Unrepairable Overhanging of Dental Restorative Materials; Poor Aesthetics of Existing Restoration; Secondary Dental Caries Associated With Failed or Defective Dental Restorations; Fractured Dental Restorative Materials Without Loss of Materials; Fracture of Dental Restorative Materials With Loss of Material

Sulfonated graphene oxide/nafion composite membrane for vanadium redox flow battery.

PubMed

Kim, Byung Guk; Han, Tae Hee; Cho, Chang Gi

2014-12-01

Nafion is the most frequently used as the membrane material due to its good proton conductivity, and excellent chemical and mechanical stabilities. But it is known to have poor barrier property due to its well-developed water channels. In order to overcome this drawback, graphene oxide (GO) derivatives were introduced for Nafion composite membranes. Sulfonated graphene oxide (sGO) was prepared from GO. Both sGO and GO were treated each with phenyl isocyanate and transformed into corresponding isGO and iGO in order to promote miscibility with Nafion. Then composite membranes were obtained, and the adaptability as a membrane for vanadium redox flow battery (VRFB) was investigated in terms of proton conductivity and vanadium permeability. Compared to a pristine Nafion, proton conductivities of both isGO/Nafion and iGO/Nafion membranes showed less temperature sensitivity. Both membranes also showed quite lower vanadium permeability at room temperature. Selectivity of the membrane was the highest for isGO/Nafion and the lowest for the pristine Nafion.

Self-assembly of dodecaphenyl POSS thin films

NASA Astrophysics Data System (ADS)

Handke, Bartosz; Klita, Łukasz; Niemiec, Wiktor

2017-12-01

The self-assembly abilities of Dodecaphenyl Polyhedral Oligomeric Silsesquioxane thin films on Si(1 0 0) surfaces were studied. Due to their thermal properties - relatively low sublimation temperature and preservation of molecular structure - cage type silsesquioxanes are ideal material for the preparation of a thin films by Physical Vapor Deposition. The Ultra-High Vacuum environment and the deposition precision of the PVD method enable the study of early stages of thin film growth and its molecular organization. X-ray Reflectivity and Atomic Force Microscopy measurements allow to pursuit size-effects in the structure of thin films with thickness ranges from less than a single molecular layer up to several tens of layers. Thermal treatment of the thin films triggered phase change: from a poorly ordered polycrystalline film into a well-ordered multilayer structure. Self-assembly of the layers is the effect of the π-stacking of phenyl rings, which force molecules to arrange in a superlattice, forming stacks of alternating organic-inorganic layers.

Surface structure and electrochemical characteristics of Ti-V-Cr bcc-type solid solution alloys sintered with Ni

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsuji, Yoichiro; Yamamoto, Osamu; Matsuda, Hiromu

2000-07-01

Ti-V-Cr bcc-type solid solution alloys can absorb a large amount of hydrogen and be applied to active materials of the negative electrode in Ni-MH batteries. However, because of the insolubility of Ni into these alloys, the electrochemical characteristics like discharge capacity and cycle life were poor. In order to increase the discharge capacity of hydrogen absorbing alloy electrodes, Ti-V-Cr bcc-type alloy powders were sintered with Ni in order to form Ni contained surface layer on the alloy surface. As sintering temperature rose up, the surface composition changed from TiNi to Ti{sub 2}Ni. TiNi surface layer showed better electrochemical characteristics. Formore » the Ni adding method, Ni electroless plating was preferred because of good adhesion. As a result of optimized conditions, a discharge capacity of 570 mAh/g and an improvement of cycle life were achieved.« less

Stiff, Thermally Stable and Highly Anisotropic Wood-Derived Carbon Composite Monoliths for Electromagnetic Interference Shielding.

PubMed

Yuan, Ye; Sun, Xianxian; Yang, Minglong; Xu, Fan; Lin, Zaishan; Zhao, Xu; Ding, Yujie; Li, Jianjun; Yin, Weilong; Peng, Qingyu; He, Xiaodong; Li, Yibin

2017-06-28

Electromagnetic interference (EMI) shielding materials for electronic devices in aviation and aerospace not only need lightweight and high shielding effectiveness, but also should withstand harsh environments. Traditional EMI shielding materials often show heavy weight, poor thermal stability, short lifetime, poor tolerance to chemicals, and are hard-to-manufacture. Searching for high-efficiency EMI shielding materials overcoming the above weaknesses is still a great challenge. Herein, inspired by the unique structure of natural wood, lightweight and highly anisotropic wood-derived carbon composite EMI shielding materials have been prepared which possess not only high EMI shielding performance and mechanical stable characteristics, but also possess thermally stable properties, outperforming those metals, conductive polymers, and their composites. The newly developed low-cost materials are promising for specific applications in aerospace electronic devices, especially regarding extreme temperatures.

Ion-beam-assisted etching of diamond

NASA Technical Reports Server (NTRS)

Efremow, N. N.; Geis, M. W.; Flanders, D. C.; Lincoln, G. A.; Economou, N. P.

1985-01-01

The high thermal conductivity, low RF loss, and inertness of diamond make it useful in traveling wave tubes operating in excess of 500 GHz. Such use requires the controlled etching of type IIA diamond to produce grating like structures tens of micrometers deep. Previous work on reactive ion etching with O2 gave etching rates on the order of 20 nm/min and poor etch selectivity between the masking material (Ni or Cr) and the diamond. An alternative approach which uses a Xe(+) beam and a reactive gas flux of NO2 in an ion-beam-assisted etching system is reported. An etching rate of 200 nm/min was obtained with an etching rate ratio of 20 between the diamond and an aluminum mask.

Biotechnological applications of transglutaminases.

PubMed

Rachel, Natalie M; Pelletier, Joelle N

2013-10-22

In nature, transglutaminases catalyze the formation of amide bonds between proteins to form insoluble protein aggregates. This specific function has long been exploited in the food and textile industries as a protein cross-linking agent to alter the texture of meat, wool, and leather. In recent years, biotechnological applications of transglutaminases have come to light in areas ranging from material sciences to medicine. There has also been a substantial effort to further investigate the fundamentals of transglutaminases, as many of their characteristics that remain poorly understood. Those studies also work towards the goal of developing transglutaminases as more efficient catalysts. Progress in this area includes structural information and novel chemical and biological assays. Here, we review recent achievements in this area in order to illustrate the versatility of transglutaminases.

A theranostic dental pulp capping agent with improved MRI and CT contrast and biological properties.

PubMed

Mastrogiacomo, S; Güvener, N; Dou, W; Alghamdi, H S; Camargo, W A; Cremers, J G O; Borm, P J A; Heerschap, A; Oosterwijk, E; Jansen, J A; Walboomers, X F

2017-10-15

Different materials have been used for vital dental pulp treatment. Preferably a pulp capping agent should show appropriate biological performance, excellent handling properties, and a good imaging contrast. These features can be delivered into a single material through the combination of therapeutic and diagnostic agents (i.e. theranostic). Calcium phosphate based composites (CPCs) are potentially ideal candidate for pulp treatment, although poor imaging contrast and poor dentino-inductive properties are limiting their clinical use. In this study, a theranostic dental pulp capping agent was developed. First, imaging properties of the CPC were improved by using a core-shell structured dual contrast agent (csDCA) consisting of superparamagnetic iron oxide (SPIO) and colloidal gold, as MRI and CT contrast agent respectively. Second, biological properties were implemented by using a dentinogenic factor (i.e. bone morphogenetic protein 2, BMP-2). The obtained CPC/csDCA/BMP-2 composite was tested in vivo, as direct pulp capping agent, in a male Habsi goat incisor model. Our outcomes showed no relevant alteration of the handling and mechanical properties (e.g. setting time, injectability, and compressive strength) by the incorporation of csDCA particles. In vivo results proved MRI contrast enhancement up to 7weeks. Incisors treated with BMP-2 showed improved tertiary dentin deposition as well as faster cement degradation as measured by µCT assessment. In conclusion, the presented theranostic agent matches the imaging and regenerative requirements for pulp capping applications. In this study, we combined diagnostic and therapeutic agents in order to developed a theranostic pulp capping agent with enhanced MRI and CT contrast and improved dentin regeneration ability. In our study we cover all the steps from material preparation, mechanical and in vitro characterization, to in vivo study in a goat dental model. To the best of our knowledge, this is the first time that a theranostic pulp capping material have been developed and tested in an in vivo animal model. Our promising results in term of imaging contrast enhancement and of induction of new dentin formation, open a new scenario in the development of innovative dental materials. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Speech Perception Deficits in Poor Readers: Auditory Processing or Phonological Coding?

ERIC Educational Resources Information Center

Mody, Maria; And Others

1997-01-01

Forty second-graders, 20 good and 20 poor readers, completed a /ba/-/da/ temporal order judgment (TOJ) task. The groups did not differ in TOJ when /ba/ and /da/ were paired with more easily discriminated syllables. Poor readers' difficulties with /ba/-/da/ reflected perceptual confusion between phonetically similar syllables rather than difficulty…

Zero-order release and bioavailability enhancement of poorly water soluble Vinpocetine from self-nanoemulsifying osmotic pump tablet.

PubMed

El-Zahaby, Sally A; AbouGhaly, Mohamed H H; Abdelbary, Ghada A; El-Gazayerly, Omaima N

2017-06-08

Solid self-nanoemulsifying (S-SNEDDS) asymmetrically coated osmotic tablets of the poorly water-soluble drug Vinpocetine (VNP) were designed. The aim was to control the release of VNP by the osmotic technology taking advantage of the solubility and bioavailability-enhancing capacity of S-SNEDDS. Liquid SNEDDS loaded with 2.5 mg VNP composed of Maisine™ 35-1, Transcutol ® HP, and Cremophor ® EL was adsorbed on the solid carrier Aeroperl ® . S-SNEDDS was mixed with the osmotic tablet excipients (sodium chloride, Avicel ® , HPMC-K4M, PVP-K30, and Lubripharm ® ), then directly compressed to form the core tablet. The tablets were dip coated and mechanically drilled. A 3 2 *2 1 full factorial design was adopted. The independent variables were: type of coating material (X 1 ), concentration of coating solution (X 2 ), and number of drills (X 3 ). The dependent variables included % release at 2 h (Y 1 ), at 4 h (Y 2 ), and at 8 h (Y 3 ). The in vivo performance of the optimum formula was assessed in rabbits. Zero-order VNP release was obtained by the single drilled 1.5% Opadry ® CA coated osmotic tablets and twofold increase in VNP bioavailability was achieved. The combination of SNEDDS and osmotic pump tablet system was successful in enhancing the solubility and absorption of VNP as well as controlling its release.

Reversibility and intermediate steps as key tools for the growth of extended ordered polymers via on-surface synthesis

NASA Astrophysics Data System (ADS)

Di Giovannantonio, Marco; Contini, Giorgio

2018-03-01

Surface-confined polymerization is a bottom-up strategy to create one- and two-dimensional covalent organic nanostructures with a π-conjugated backbone, which are suitable to be employed in real-life electronic devices, due to their high mechanical resistance and electronic charge transport efficiency. This strategy makes it possible to change the properties of the final nanostructures by a careful choice of the monomer architecture (i.e. of its constituent atoms and their spatial arrangement). Several chemical reactions have been proven to form low-dimensional polymers on surfaces, exploiting a variety of precursors in combination with metal (e.g. Cu, Ag, Au) and insulating (e.g. NaCl, CaCO3) surfaces. One of the main challenges of such an approach is to obtain nanostructures with long-range order, to boost the conductance performances of these materials. Most of the exploited chemical reactions use irreversible coupling between the monomers and, as a consequence, the resulting structures often suffer from poor order and high defect density. This review focuses on the state-of-the-art surface-confined polymerization reactions, with particular attention paid to reversible coupling pathways and irreversible processes including intermediate states, which are key aspects to control to increase the order of the final nanostructure.

Applicability of cranial models in urethane resin and foam as a substitute for bone: are synthetic materials reliable?

PubMed

Muccino, Enrico; Porta, Davide; Magli, Francesca; Cigada, Alfredo; Sala, Remo; Gibelli, Daniele; Cattaneo, Cristina

2013-09-01

As literature is poor in functional synthetic cranial models, in this study, synthetic handmade models of cranial vaults were produced in two different materials (a urethane resin and a self-hardening foam), from multiple bone specimens (eight original cranial vaults: four human and four swine), in order to test their resemblance to bone structure in behavior, during fracture formation. All the vaults were mechanically tested with a 2-kg impact weight and filmed with a high-speed camera. Fracture patterns were homogeneous in all swine vaults and heterogeneous in human vaults, with resin fractures more similar to bone fractures. Mean fracture latency time extrapolated by videos were of 0.75 msec (bone), 1.5 msec (resin), 5.12 msec (foam) for human vaults and of 0.625 msec (bone), 1.87 msec (resin), 3.75 msec (foam) for swine vaults. These data showed that resin models are more similar to bone than foam reproductions, but that synthetic material may behave quite differently from bone as concerns fracture latency times. © 2013 American Academy of Forensic Sciences.

Structural geology and geological history of the Perrine and Nun Sulci Quadrangles (Jg-2 and Jg-5), Ganymede

NASA Technical Reports Server (NTRS)

Mcgill, George E.; Squyres, Steven W.

1991-01-01

Grooves are the dominant structural features on Ganymede. While single grooves are found in many areas, it is somewhat more common to find them grouped together in groove sets (groupings of grooves with common structural trends). It is generally believed that the grooves are extensional features. Their underlying geologic nature cannot be determined from Voyager images, however. It appears likely that they are grabens, but the images are insufficient to rule out the possibility that they are modified extension fractures or some kind of ductile necking features. The oldest materials within the Nun Sulci and Perrine quadrangles occur within the cratered dark materials unit, as is generally the case for all of Ganymede. This is the most widespread of the dark units mapped in these two quadrangles. Crater densities within cratered dark materials are consistent with an age on the order of several billion years, and thus cratered dark terrain probably represents crust that has survived from the end of the primordial intense bombardment phase of solar system history. The brief geologic history is greatly oversimplified as a result of the poor resolution and unfavorable viewing geometry of the images covering the area.

Rupture testing for the quality control of electrodeposited copper interconnections in high-speed, high-density circuits

NASA Technical Reports Server (NTRS)

Zakraysek, Louis

1987-01-01

Printed Wiring Multilayer Board (PWMLB) structures for high speed, high density circuits are prone to failure due to the microcracking of electrolytic copper interconnections. The failure can occur in the foil that makes up the inner layer traces or in the plated through holes (PTH) deposit that forms the layer to layer interconnections. It is shown that there are some distinctive differences in the quality of Type E copper and that these differences can be detected before its use in a PWMLB. It is suggested that the strength of some Type E copper can be very low when the material is hot and that it is the use of this poor quality material in a PWMLB that results in PTH and inner layer microcracking. Since the PWMLB failure in question are induced by a thermal stress, and since the poorer grades of Type E materials used in these structures are susceptible to premature failure under thermal stress, the use of elevated temperature rupture and creep rupture testing is proposed as a means for screening copper foil, or its PTH equivalent, in order to eliminate the problem of Type E copper microcracking in advanced PWMLBs.

Material, psychosocial and sociodemographic determinants are associated with positive mental health in Europe: a cross-sectional study

PubMed Central

Dreger, Stefanie; Buck, Christoph; Bolte, Gabriele

2014-01-01

Objectives To investigate the association between psychosocial, sociodemographic and material determinants of positive mental health in Europe. Design Cross-sectional analysis of survey data. Setting 34 European countries. Participants Representative Europe-wide sample consisting of 21 066 men and 22 569 women aged 18 years and over, from 34 European countries participating in the third wave of the European Quality of Life Survey (2011–2012). Outcome Positive mental health as measured by the WHO-5—Mental Well-being Index, while the lowest 25% centile indicated poor positive mental health. Results The prevalence of poor positive mental health was 30% in women and 24% in men. Material, as well as psychosocial, and sociodemographic factors were independently associated with poor positive mental health in a Europe-wide sample from 34 European countries. When studying all factors together, the highest OR for poor positive mental health was reported for social exclusion (men: OR=1.73, 95% CI 1.59 to 1.90; women: OR=1.69, 95% CI 1.57 to 1.81) among the psychosocial factors. Among the material factors, material deprivation had the highest impact (men: OR=1.96, 95% CI 1.78 to 2.15; women: OR=1.93, 95% CI 1.79 to 2.08). Conclusions This study gives the first overview on determinants of positive mental health at a European level and could be used as the basis for preventive policies in the field of positive mental health in Europe. PMID:24871540

Performances of some low-cost counter electrode materials in CdS and CdSe quantum dot-sensitized solar cells.

PubMed

Jun, Hieng Kiat; Careem, Mohamed Abdul; Arof, Abdul Kariem

2014-02-10

Different counter electrode (CE) materials based on carbon and Cu2S were prepared for the application in CdS and CdSe quantum dot-sensitized solar cells (QDSSCs). The CEs were prepared using low-cost and facile methods. Platinum was used as the reference CE material to compare the performances of the other materials. While carbon-based materials produced the best solar cell performance in CdS QDSSCs, platinum and Cu2S were superior in CdSe QDSSCs. Different CE materials have different performance in the two types of QDSSCs employed due to the different type of sensitizers and composition of polysulfide electrolytes used. The poor performance of QDSSCs with some CE materials is largely due to the lower photocurrent density and open-circuit voltage. The electrochemical impedance spectroscopy performed on the cells showed that the poor-performing QDSSCs had higher charge-transfer resistances and CPE values at their CE/electrolyte interfaces.

The geologic classification of the meteorites

USGS Publications Warehouse

Elston, Donald Parker

1968-01-01

The meteorite classes of Prior and Mason are assigned to three proposed genetic groups on the basis of a combination of compositional, mineralogical, and elemental characteristics: l) the calcium-poor, volatile-rich carbonaceous chondrites and achondrites; 2) the calcium-poor, volatile-poor chondrites (enstatite, bronzite, hypersthene, and pigeonite), achondrites (enstatite, hypersthene, and pigeonite), stonyirons (pallasites, siderophyre), and irons; and, 3) the calcium-rich (basaltic) achondrites. Chondrites are correlated with calcium-poor achondrites and the silicate phase of the pallasitic meteorites on Fe contents of olivine and pyroxene; and with metal of the stony-irons and irons on the basis of trace elements (Ga and Ge). Transitions in structure and texture between the chondrites and achondrites are recognized. The Van Schmus-Wood chemical-petrologic classification of the chondrites has been modified and expanded to a mineralogic-petrologic classification of the chondrites and calcium-poor achondrites. Chondrites apparently are the first rocks of the solar system. Paragenetic and textural relations in the Murray carbonaceous chondrite shed new light on the manner of accretion, and on the character of dispersed solid materials ('dust', and chondrules and metal) that existed in the solar system before accretion. Two pre-accretionary mineral assemblages (components) are recognized in the carbonaceous chondrites and in the unequilibrated volatile-poor chondrites. They are: 1) a 'low temperature' water-, rare gas-, and carbon-bearing component; and, 2) a high temperature anhydrous silicate and metal component. Paragenetic relations indicate that component 2 materials predate chondrite formation. An accretionary assemblage (component 3) also is recognized in the carbonaceous chondrites and in the unequilibrated volatile-poor chondrites. Component 3 consists of very fine grains of olivine and pyroxene, which occur as pervasive disseminations, as small irregular aggregates of grains, and as large subround to round, finely granular accretional chondrules. Evidence in Murray indicates that component 3 silicates precipitated abruptly and at low pressures, possibly from a high temperature gas, in an environment that contained dispersed component 1 and 2 materials. All component 3 aggregates in Murray contain component 1 material, most commonly as flakes, and locally as tiny granules and larger spherules, some of which are hollow and some of which were broken prior to their mechanical incorporation in accretionary chondrules. Accretion may have occurred as ices associated with dispersed water-bearing component 1 materials temporarily melted during the precipitation of component 3 silicates, and then abruptly refroze to form an icy cementing material. Group 1 materials may be cometary, and group 2 materials may be asteroidal. Schematic models are proposed. Evidence is reviewed for the lunar origin of the pyroxeneplagioclase achondrites. On the basis of natural remanent magnetism, it is suggested that the very scarce diopside-olivine achondrites may be samples from Mars. A classification of the meteorite breccias, including the calcium-poor and calcium-rich mesosiderites, and irons that contain silicate fragments, is proposed. A fragmentation history of the meteorites is outlined on the basis of evidence in the polymict breccias, and from gas retention ages in stones and exposure ages in irons. Cometal impacts appear to have caused the initial fragmentation, stud possibly the perturbation of orbits, of two inferred asteroidal bodies (enstatite and bronzite), one and possibly both events occurring before 2000 m.y. ago. Several impacts apparently occurred on the inferred hypersthene body in the interval 1000 to 2000 m.y. ago. Major breakups of the three bodies apparently occurred as the result of interasteroidal collisions at about 900 m.y. ago, and 600 to 700 m.y. ago. The breakups were followed by a number of fr

The relationship between two visual communication systems: reading and lipreading.

PubMed

Williams, A

1982-12-01

To explore the relationship between reading and lipreading and to determine whether readers and lipreaders use similar strategies to comprehend verbal messages, 60 female junior and sophomore high school students--30 good and 30 poor readers--were given a filmed lipreading test, a test to measure eye-voice span, a test of cloze ability, and a test of their ability to comprehend printed material presented one word at a time in the absence of an opportunity to regress or scan ahead. The results of this study indicated that (a) there is a significant relationship between reading and lipreading ability; (b) although good readers may be either good or poor lipreaders, poor readers are more likely to be poor than good lipreaders; (c) there are similarities in the strategies used by readers and lipreaders in their approach to comprehending spoken and written material; (d) word-by-word reading of continuous prose appears to be a salient characteristic of both poor reading and poor lipreading ability; and (c) good readers and lipreaders do not engage in word-by-word reading but rather use a combination of visual and linguistic cues to interpret written and spoken messages.

Seebeck Coefficient Metrology: Do Contemporary Protocols Measure Up?

NASA Astrophysics Data System (ADS)

Martin, Joshua; Wong-Ng, Winnie; Green, Martin L.

2015-06-01

Comparative measurements of the Seebeck coefficient are challenging due to the diversity of instrumentation and measurement protocols. With the implementation of standardized measurement protocols and the use of Standard Reference Materials (SRMs®), for example, the recently certified National Institute of Standards and Technology (NIST) SRM® 3451 ``Low Temperature Seebeck Coefficient Standard (10-390 K)'', researchers can reliably analyze and compare data, both intra- and inter-laboratory, thereby accelerating the development of more efficient thermoelectric materials and devices. We present a comparative overview of commonly adopted Seebeck coefficient measurement practices. First, we examine the influence of asynchronous temporal and spatial measurement of electric potential and temperature. Temporal asynchronicity introduces error in the absolute Seebeck coefficient of the order of ≈10%, whereas spatial asynchronicity introduces error of the order of a few percent. Second, we examine the influence of poor thermal contact between the measurement probes and the sample. This is especially critical at high temperature, wherein the prevalent mode of measuring surface temperature is facilitated by pressure contact. Each topic will include the comparison of data measured using different measurement techniques and using different probe arrangements. We demonstrate that the probe arrangement is the primary limit to high accuracy, wherein the Seebeck coefficients measured by the 2-probe arrangement and those measured by the 4-probe arrangement diverge with the increase in temperature, approaching ≈14% at 900 K. Using these analyses, we provide recommended measurement protocols to guide members of the thermoelectric materials community in performing more accurate measurements and in evaluating more comprehensive uncertainty limits.

Inequality in early childhood neurodevelopment in six poor rural counties of China: a decomposition analysis.

PubMed

Zhang, Cuihong; Zhao, Chunxia; Liu, Xiangyu; Wei, Qianwei; Luo, Shusheng; Guo, Sufang; Zhang, Jingxu; Wang, Xiaoli; Scherpbier, Robert W

2017-12-08

Previous studies about inequality in children's health focused more on physical health than the neurodevelopment. In this study, we aimed to evaluate the inequality in early childhood neurodevelopment in poor rural China and explore the contributions of socioeconomic factors to the inequality. Information of 2120 children aged 0 to 35 months and their households in six poor rural counties of China was collected during July - September, 2013. Age and Stages Questionnaire-Chinese version, concentration index and decomposition analysis were used to assess the neurodevelopment of early childhood, measure its inequality and evaluate the contributions of socioeconomic factors to the inequality, respectively. The prevalence of suspected developmental delay in children under 35 months of age in six poor rural counties of China was nearly 40%, with the concentration index of -0.0877. Household economic status, caregivers' depressive symptoms, learning material and family support for learning were significantly associated with children's suspected developmental delay, and explained 34.1, 14.1, 8.9 and 7.0% of the inequality in early childhood neurodevelopment, respectively. The early childhood neurodevelopment in the surveyed area is poor and unfair. Factors including household economic status, caregivers' depressive symptoms, learning material and family support for learning are significantly associated with children's suspected developmental delay and early developmental inequality. The results highlight the urgent need of monitoring child neurodevelopment in poor rural areas. Interventions targeting the caregivers' depressive symptoms, providing learning material and developmental appropriate stimulating activities may help improve early childhood neurodevelopment and reduce its inequality.

High Pressure and Temperature Effects in Polymers

NASA Astrophysics Data System (ADS)

Bucknall, David; Arrighi, Valeria; Johnston, Kim; Condie, Iain

Elastomers are widely exploited as the basis for seals in gas and fluid pipelines. The underlying behaviour of these elastomer at the high pressure, elevated temperatures they experience in operation is poorly understood. Consequently, the duty cycle of these materials is often deliberately limited to a few hours, and in order to prevent failure, production is stopped in order to change the seals in critical joints. The result is significant time lost due to bringing down production to change the seals as well as knock on financial costs. In order to address the fundamental nature of the elastomers at their intended operating conditions, we are studying the gas permeation behaviour of hydrogenated natural butyl rubber (HNBR) and fluorinated elastomers (FKM) at a high pressure and elevated temperature. We have developed a pressure system that permits gas permeation studies at gas pressures of up to 5000 psi and operating temperatures up to 150° C. In this paper, we will discuss the nature of the permeation behaviour at these extreme operating conditions, and how this relates to the changes in the polymer structure. We will also discuss the use of graphene-polymer thin layer coatings to modify the gas permeation behaviour of the elastomers.

Rich and poor states in the Middle East: Egypt and the New Arab Order

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herr, M.H.; Yassin, E.S.

1982-01-01

While oil wealth has enriched some Middle East Arab nations, those lacking oil resources have remained poor and are looking now to their oil-rich neighbors for development assistance. This collection of studies on the economic, social, and political relationships between the have and the have-nots focuses on Egypt, the largest state in the region, and on its prospects for change based on financial assistance from other Arab countries. The 13 authors disagree about the future of both rich and poor nations, and are skeptical about the possibility of transforming Egypt. They do agree that the future must be projected inmore » the framework of a new regional order in which oil wealth, labor migration, and a new regional order in which oil wealth, labor migration, and liberalized national economies are fundamental realities. 615 references, 5 figures, 67 tables.« less

Variations in algorithm implementation among quantitative texture analysis software packages

NASA Astrophysics Data System (ADS)

Foy, Joseph J.; Mitta, Prerana; Nowosatka, Lauren R.; Mendel, Kayla R.; Li, Hui; Giger, Maryellen L.; Al-Hallaq, Hania; Armato, Samuel G.

2018-02-01

Open-source texture analysis software allows for the advancement of radiomics research. Variations in texture features, however, result from discrepancies in algorithm implementation. Anatomically matched regions of interest (ROIs) that captured normal breast parenchyma were placed in the magnetic resonance images (MRI) of 20 patients at two time points. Six first-order features and six gray-level co-occurrence matrix (GLCM) features were calculated for each ROI using four texture analysis packages. Features were extracted using package-specific default GLCM parameters and using GLCM parameters modified to yield the greatest consistency among packages. Relative change in the value of each feature between time points was calculated for each ROI. Distributions of relative feature value differences were compared across packages. Absolute agreement among feature values was quantified by the intra-class correlation coefficient. Among first-order features, significant differences were found for max, range, and mean, and only kurtosis showed poor agreement. All six second-order features showed significant differences using package-specific default GLCM parameters, and five second-order features showed poor agreement; with modified GLCM parameters, no significant differences among second-order features were found, and all second-order features showed poor agreement. While relative texture change discrepancies existed across packages, these differences were not significant when consistent parameters were used.

The electrical conductivities of candidate beam-waveguide antenna shroud materials

NASA Technical Reports Server (NTRS)

Otoshi, T. Y.; Franco, M. M.

1994-01-01

The shroud on the beam-waveguide (BWG) antenna at DSS 13 is made from highly magnetic American Society for Testing and Materials (ASTM) A36 steel. Measurements at 8.42 GHz showed that this material (with paint) has a very poor electrical conductivity that is 600 times worse than aluminum. In cases where the BWG mirrors might be slightly misaligned, unintentional illumination and poor electrical conductivity of the shroud walls can cause system noise temperature to be increased significantly. This potential increase of noise temperature contribution can be reduced through the use of better conductivity materials for the shroud walls. An alternative is to attempt to improve the conductivity of the currently used ASTM A36 steel by means of some type of plating, surface treatment, or high-conductivity paints. This article presents the results of a study made to find improved materials for future shrouds and mirror supports.

Crystal Chemistry and Electrochemistry of Li xMn 1.5Ni 0.5O 4 Solid Solution Cathode Materials

DOE PAGES

Kan, Wang Hay; Kuppan, Saravanan; Cheng, Lei; ...

2017-07-19

For ordered high-voltage spinel LiMn 1.5Ni 0.5O 4 (LMNO) with the P4 32 1 symmetry, the two consecutive two-phase transformations at ~4.7 V (vs Li +/Li), involving three cubic phases of LMNO, Li 0.5Mn 1.5Ni 0.5O 4 (L 0.5MNO), and Mn 1.5Ni 0.5O 4 (MNO), have been well-established. Such a mechanism is traditionally associated with poor kinetics due to the slow movement of the phase boundaries and the large mechanical strain resulting from the volume changes among the phases, yet ordered LMNO has been shown to have excellent rate capability. In this paper, we show the ability of the phasesmore » to dissolve into each other and determine their solubility limit. We characterized the properties of the formed solid solutions and investigated the role of non-equilibrium single-phase redox processes during the charge and discharge of LMNO. Finally, by using an array of advanced analytical techniques, such as soft and hard X-ray spectroscopy, transmission X-ray microscopy, and neutron/X-ray diffraction, as well as bond valence sum analysis, the present study examines the metastable nature of solid-solution phases and provides new insights in enabling cathode materials that are thermodynamically unstable.« less

An accurate computational method for an order parameter with a Markov state model constructed using a manifold-learning technique

NASA Astrophysics Data System (ADS)

Ito, Reika; Yoshidome, Takashi

2018-01-01

Markov state models (MSMs) are a powerful approach for analyzing the long-time behaviors of protein motion using molecular dynamics simulation data. However, their quantitative performance with respect to the physical quantities is poor. We believe that this poor performance is caused by the failure to appropriately classify protein conformations into states when constructing MSMs. Herein, we show that the quantitative performance of an order parameter is improved when a manifold-learning technique is employed for the classification in the MSM. The MSM construction using the K-center method, which has been previously used for classification, has a poor quantitative performance.

Inductive learning of thyroid functional states using the ID3 algorithm. The effect of poor examples on the learning result.

PubMed

Forsström, J

1992-01-01

The ID3 algorithm for inductive learning was tested using preclassified material for patients suspected to have a thyroid illness. Classification followed a rule-based expert system for the diagnosis of thyroid function. Thus, the knowledge to be learned was limited to the rules existing in the knowledge base of that expert system. The learning capability of the ID3 algorithm was tested with an unselected learning material (with some inherent missing data) and with a selected learning material (no missing data). The selected learning material was a subgroup which formed a part of the unselected learning material. When the number of learning cases was increased, the accuracy of the program improved. When the learning material was large enough, an increase in the learning material did not improve the results further. A better learning result was achieved with the selected learning material not including missing data as compared to unselected learning material. With this material we demonstrate a weakness in the ID3 algorithm: it can not find available information from good example cases if we add poor examples to the data.

Factors associated with unintended pregnancy, poor birth outcomes and post-partum contraceptive use among HIV-positive female adolescents in Kenya

PubMed Central

2012-01-01

Background Although the experiences of unintended pregnancies and poor birth outcomes among adolescents aged 15–19 years in the general population are well documented, there is limited understanding of the same among those who are living with HIV. This paper examines the factors associated with experiencing unintended pregnancies, poor birth outcomes, and post-partum contraceptive use among HIV-positive female adolescents in Kenya. Methods Data are from a cross-sectional study that captured information on pregnancy histories of HIV-positive female adolescents in four regions of Kenya: Coast, Nairobi, Nyanza and Rift Valley provinces. Study participants were identified through HIV and AIDS programs in the four regions. Out of a total of 797 female participants, 394 had ever been pregnant with 24% of them experiencing multiple pregnancies. Analysis entails the estimation of random-effects logit models. Results Higher order pregnancies were just as likely to be unintended as lower order ones (odds ratios [OR]: 1.2; 95% confidence interval [CI]: 0.8–2.0) while pregnancies occurring within marital unions were significantly less likely to be unintended compared to those occurring outside such unions (OR: 0.1; 95% CI: 0.1–0.2). Higher order pregnancies were significantly more likely to result in poor outcomes compared to lower order ones (OR: 2.5; 95% CI: 1.6–4.0). In addition, pregnancies occurring within marital unions were significantly less likely to result in poor outcomes compared to those occurring outside such unions (OR: 0.3; 95% CI: 0.1–0.9). However, experiencing unintended pregnancy was not significantly associated with adverse birth outcomes (OR: 1.3; 95% CI: 0.5–3.3). There was also no significant difference in the likelihood of post-partum contraceptive use by whether the pregnancy was unintended (OR: 0.9; 95% CI: 0.5–1.5). Conclusions The experience of repeat unintended pregnancies among HIV-positive female adolescents in the sample is partly due to inconsistent use of contraception to prevent recurrence while poor birth outcomes among higher order pregnancies are partly due to abortion. This underscores the need for HIV and AIDS programs to provide appropriate sexual and reproductive health information and services to HIV-positive adolescent clients in order to reduce the risk of undesired reproductive health outcomes. PMID:23039966

Hydraulic properties of groundwater systems in the saprolite and sediments of the wheatbelt, Western Australia

NASA Astrophysics Data System (ADS)

George, Richard J.

1992-01-01

Hydraulic properties of deeply weathered basement rocks and variably weathered sedimentary materials were measured by pumping and slug-test methods. Results from over 200 bores in 13 catchments, and eight pumping-test sites across the eastern and central wheatbelt of Western Australia were analysed. Measurements were made in each of the major lithological units, and emphasis placed on a ubiquitous basal saprolite aquifer. Comparisons were made between alternative drilling and analytical procedures to determine the most appropriate methods of investigation. Aquifers with an average hydraulic conductivity of 0.55 m day -1 occur in variably weathered Cainozoic sediments and poorly weathered saprolite grits (0.57 m day -1). These aquifers are separated by an aquitard (0.065 m day -1) comprising the mottled and pallid zones of the deeply weathered profile. Locally higher values of hydraulic conductivity occur in the saprolite aquifer, although after prolonged periods of pumping the values decrease until they are similar to those obtained from the slug-test methods. Hydraulic conductivities measured in bores drilled with rotary auger rigs were approximately an order of magnitude lower than those measured in the same material with bores drilled by the rotary air-blast method. Wheatbelt aquifers range from predominantly unconfined (Cainozoic sediments), to confined (saprolite grit aquifer). The poorly weathered saprolite grit aquifer has moderate to high transmissivities (4-50 m 2 day -1) and is capable of producing from less than 5 to over 230 kl day -1 of ground water, which is often of a quality suitable for livestock. Yields are influenced by the variability in the permeability of isovolumetrically weathered materials from which the aquifer is derived. The overlying aquitard has a low transmissivity (< 1 m 2 day -1), especially when deeply weathered, indurated and silicified. The transmissivity of the variably weathered sedimentary materials ranges from less than 0.5 m 2 day -1 to over 10 m 2 day -1, depending on the texture of the materials and their position within the landscape. Higher transmissivity zones may occur as discrete layers of coarser textured materials. The salinity of the saprolite and sedimentary aquifers ranges from less than 2000 mgl -1 to greater than 250000 mgl -1 (total dissolved solids; TDS), depending on position within the landscape. Secondary soil salinization develops when groundwater discharge occurs from either saprolite or sedimentary aquifers.

A comparative study of interface reconstruction methods for multi-material ALE simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kucharik, Milan; Garimalla, Rao; Schofield, Samuel

2009-01-01

In this paper we compare the performance of different methods for reconstructing interfaces in multi-material compressible flow simulations. The methods compared are a material-order-dependent Volume-of-Fluid (VOF) method, a material-order-independent VOF method based on power diagram partitioning of cells and the Moment-of-Fluid method (MOF). We demonstrate that the MOF method provides the most accurate tracking of interfaces, followed by the VOF method with the right material ordering. The material-order-independent VOF method performs some-what worse than the above two while the solutions with VOF using the wrong material order are considerably worse.

Poor Performance in Mathematics: Is There a Basis for a Self-Worth Explanation for Women?

ERIC Educational Resources Information Center

Thompson, Ted; Dinnel, Dale L.

2007-01-01

The self-worth theory of achievement motivation holds that in situations in which poor performance is likely to reveal low ability, certain students (known as self-worth protective students) intentionally withdraw effort in order to avoid the negative implications of poor performance in terms of damage to self-worth. In this study, evidence of…

An Evanescent Microwave Probe for Super-Resolution Nondestructive Imaging of Metals, Semiconductors, Dielectrics, Composites and Biological Specimens

NASA Technical Reports Server (NTRS)

Pathak, P. S.; Tabib-Azar, M.; Ponchak, G.

1998-01-01

Using evanescent microwaves with decay lengths determined by a combination of microwave wavelength (lambda) and waveguide termination geometry, we have imaged and mapped material non-uniformities and defects with a resolving capability of lambda/3800=79 microns at 1 GHz. In our method a microstrip quarter wavelength resonator was used to generate evanescent microwaves. We imaged materials with a wide range of conductivities. Carbon composites, dielectrics (Duroid, polymers), semiconductors (3C-SiC, polysilicon, natural diamond), metals (tungsten alloys, copper, zinc, steel), high-temperature superconductors, and botanical samples were scanned for defects, residual stresses, integrity of brazed junctions, subsurface features, areas of different film thickness and moisture content. The evanescent microwave probe is a versatile tool and it can be used to perform very fast, large scale mapping of a wide range of materials. This method of characterization compares favorably with ultrasound testing, which has a resolution of about 0.1 mm and suffers from high absorption in composite materials and poor transmission across boundaries. Eddy current methods which can have a resolution on the order of 50 microns are restricted to evaluating conducting materials. Evanescent microwave imaging, with careful choice of operating frequency and probe geometry, can have a resolution of up to 1 micron. In this method we can scan hot and moving objects, sample preparation is not required, testing is non-destructive, non-invasive and non-contact, and can be done in air, in liquid or in vacuum.

Environmental risk evaluation of the use of mine spoils and treated sewage sludge in the ecological restoration of limestone quarries

NASA Astrophysics Data System (ADS)

Jordán, M. M.; Pina, S.; García-Orenes, F.; Almendro-Candel, M. B.; García-Sánchez, E.

2008-07-01

The ecologic restoration criteria in areas degraded from extraction activities require making use of their mine spoils. These materials do not meet fertility conditions to guarantee restoration success and therefore, need the incorporation of organic amendments to obtain efficient substratum. Reducing the deficiencies in the organic material and restoration material nutrients with the contribution of treated sewage sludge is proposed in this work. This experiment was based on a controlled study using columns. The work was conducted with two mine spoils, both very rich in calcium carbonate. The first mineral, of poor quality, came from the formation of aggregates of crushed limestone ( Z). The other residual material examined originated in limestone extraction, formed by the levels of interspersed non-limestone materials and the remains of stripped soils ( D). Two treatments were undertaken (30,000 and 90,000 kg/ha of sewage sludge), in addition to a control treatment. The water contribution was carried out with a device that simulated either short-duration rain or a flooding irrigation system in order to cover the surface and then percolate through the soil. The collection of leached water took place 24 h after the applications. Different parameters of the leached water were determined, including pH, electrical conductivity, nitrate anions, ammonium, phosphates, sulphates and chlorides. The values obtained for each irrigation application are discussed, and the nitrate values obtained were very elevated.

The genus Syllis Savigny in Lamarck, 1818 (Annelida, Syllidae) from Australia. Molecular analysis and re-description of some poorly-known species.

PubMed

Álvarez-Campos, Patricia; Riesgo, Ana; Hutchings, Pat; San Martín, Guillermo

2015-12-03

The taxonomy and phylogenetic relationships within Syllis Savigny in Lamarck, 1818, the type genus of the family Syllidae, are still a matter of debate because the group does not show clear synapomorphies and because of the lack of molecular data for many of the species. In order to help understand some of the phylogenetic relationships within the genus Syllis, we have performed a morphological revision of part of the material collected during decades by the Australian Museum staff, and provide molecular data for species not sequenced before. In particular, seven poorly known Australian species of the genus Syllis Savigny in Lamarck, 1818 have been re-described in detail and sequenced to analyze their phylogenetic position: Syllis broomensis n. comb., S. crassicirrata (Treadwell, 1925) n. comb., Syllis cruzi Núñez & San Martín, 1991, S. edensis (Hartmann-Schröder, 1989), Syllis gracilis Grube, 1840, Syllis picta (Kinberg, 1866) n. comb., and S. setoensis (Imajima, 1966). The results obtained indicate the paraphyly of Typosyllis and a possible new organization of Syllis, which contains at least four well-supported clades.

Solution Coating of Pharmaceutical Nanothin Films and Multilayer Nanocomposites with Controlled Morphology and Polymorphism.

PubMed

Horstman, Elizabeth M; Kafle, Prapti; Zhang, Fengjiao; Zhang, Yifu; Kenis, Paul J A; Diao, Ying

2018-03-28

Nanosizing is rapidly emerging as an alternative approach to enhance solubility and thus the bioavailability of poorly aqueous soluble active pharmaceutical ingredients (APIs). Although numerous techniques have been developed to perform nanosizing of API crystals, precise control and modulation of their size in an energy and material efficient manner remains challenging. In this study, we present meniscus-guided solution coating as a new technique to produce pharmaceutical thin films of nanoscale thickness with controlled morphology. We demonstrate control of aspirin film thickness over more than 2 orders of magnitude, from 30 nm to 1.5 μm. By varying simple process parameters such as the coating speed and the solution concentration, the aspirin film morphology can also be modulated by accessing different coating regimes, namely the evaporation regime and the Landau-Levich regime. Using ellipticine-a poorly water-soluble anticancer drug-as another model compound, we discovered a new polymorph kinetically trapped during solution coating. Furthermore, the polymorphic outcome can be controlled by varying coating conditions. We further performed layer-by-layer coating of multilayer nanocomposites, with alternating thin films of ellipticine and a biocompatible polymer, which demonstrate the potential of additive manufacturing of multidrug-personalized dosage forms using this approach.

New Aqueous Binders for Lithium-ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jansen, Andrew N.; Krumdick, Gregory K.; Trask, Stephen E.

2016-12-22

This final report summarizes the research effort of the CRADA between PPG Industries and Argonne National Laboratory (CRADA # C1400501 and Amendment 1 - ACK 85C11, Rev. 1), and completes the requirements of Task #5 in the CRADA. The results from Argonne represent a combined effort between the MERF and CAMP Facility (Materials Engineering Research Facility and the Cell Analysis, Modeling and Prototyping Facility). The key points of this report can be briefly summarized as: The multicomponent aqueous binder for NCM cathodes developed by PPG shows promising results when used on the CAMP Facility’s pilot-scale coater; NCM523 cathode electrodes exposedmore » to water exhibit a voltage anomaly in the first two formation cycles that appears to have little effect on the material capacity, but needs to be explored further; the experimental LFP electrode produced by PPG does cycle electrochemically, but with reduced capacity and an uncharacteristic voltage profile; there is no obvious correlation between the pH and zeta-potential of materials that are commonly used in the lithium-ion battery; lithium ions are more readily dissolved out of NCM523 by water than the transition metals (by two orders of magnitude), and suggests that the plating bath may need to be spiked with a lithium salt; the approach of creating sub-micron size NCM523 particles via ball milling results in a cathode material with poor electrochemical performance.« less

Polypyrrole/sargassum activated carbon modified stainless-steel sponge as high-performance and low-cost bioanode for microbial fuel cells

NASA Astrophysics Data System (ADS)

Wu, Gaoming; Bao, Han; Xia, Zheng; Yang, Bin; Lei, Lecheng; Li, Zhongjian; Liu, Chunxian

2018-04-01

Anode materials, as the core component of microbial fuel cells (MFCs), have huge impacts on power generation performance and overall cost. Stainless-steel sponge (SS) can be a promising material for MFC anodes, due to its open continuous three-dimensional structure, high conductivity and low cost. However, poor biocompatibility limits its application. In this paper, a polypyrrole/sargassum activated carbon modified SS anode (Ppy/SAC/SS) is developed by electrochemical polymerization of pyrrole on the SS with the SAC as a dopant. The maximum power density achieved with the Ppy/SAC/SS anode is 45.2 W/m3, which is increased by 2 orders of magnitude and 2.9 times compared with an unmodified SS anode and a solely Ppy modified SS anode (Ppy/SS), respectively. In addition, the Ppy/SAC layer effectively eliminates electrochemical corrosion of the SS substrate. Electrochemical impedance spectroscopy reveals that Ppy/SAC modification decreases electron transfer resistance between the bacteria and the electrode. Furthermore, in vivo fluorescence imaging indicates that a more uniform biofilm is formed on the Ppy/SAC/SS compared to the unmodified SS and Ppy/SS. Due to the low cost of the materials, easy fabrication process and relatively high performance, our developed Ppy/SAC/SS can be a cost efficient anode material for MFCs in practical applications.

Biofiltration of Volatile Pollutants: Solubility Effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davison, Brian H.; Barton, John W.

2001-06-15

This project investigates and collects fundamental partitioning data for a variety of sparingly soluble subsurface contaminants (e.g., TCE, etc.) between vapor, aqueous phase, and matrices containing substantial quantities of biomass and biomass components. Due to the difficulty of obtaining these measurements, environmental models have generally used solubility constants of chemicals in pure water or, in a few rare cases, simple linear models. Our prior EMSP work has shown that the presence of biological material can increase effective solubilities by an order of magnitude for sparingly soluble organics; therefore, the previous simple approaches are not valid and are extremely poor predictorsmore » of actual bio-influenced partitioning. It is likely that environmental contaminants will partition in a similar manner into high-biomass phases (e.g. biobarriers and plants) or humic soils. Biological material in the subsurface can include lipids, fatty acids, humic materials, as well a s the lumped and difficult to estimate 'biomass'. Our measurements include partition into these biological materials to allow better estimation. Fundamental data collected will be used in mathematical models predicting transport and sorption in subsurface environments, with the impacts on bioremediation being evaluated based on this new information. Our 2-D Win95/98 software program, Biofilter 1.0, developed as a part of our prior EMSP efforts for describing biofiltration processes with consideration given to both kinetic and mass transfer factors, will be extended to incorporate and use this information.« less

Biofiltration of Volatile Pollutants: Solubility Effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davison, Brian H.; Barton, John W.

2002-06-15

This project investigates and collects fundamental partitioning data for a variety of sparingly soluble subsurface contaminants (e.g., TCE, etc.) between vapor, aqueous phase, and matrices containing substantial quantities of biomass and biomass components. Due to the difficulty of obtaining these measurements, environmental models have generally used solubility constants of chemicals in pure water or, in a few rare cases, simple linear models. Our prior EMSP work has shown that the presence of biological material can increase effective solubilities by an order of magnitude for sparingly soluble organics; therefore, the previous simple approaches are not valid and are extremely poor predictorsmore » of actual bio-influenced partitioning. It is likely that environmental contaminants will partition in a similar manner into high-biomass phases (e.g. biobarriers and plants) or humic soils. Biological material in the subsurface can include lipids, fatty acids, humic materials, as well as the lumped and difficult-to-estimate 'biomass'. Our measurements include partition into these biological materials to allow better estimation. Fundamental data collected will be used in mathematical models predicting transport and sorption in subsurface environments, with the impacts on bioremediation being evaluated based on this new information. Our 2-D Win95/98/XP software program, Biofilter 1.0, developed as a part of our prior EMSP efforts for describing biofiltration processes with consideration given to both kinetic and mass transfer factors, is being extended to incorporate and use this information.« less

Physical stabilization of low-molecular-weight amorphous drugs in the solid state: a material science approach.

PubMed

Qi, Sheng; McAuley, William J; Yang, Ziyi; Tipduangta, Pratchaya

2014-07-01

Use of the amorphous state is considered to be one of the most effective approaches for improving the dissolution and subsequent oral bioavailability of poorly water-soluble drugs. However as the amorphous state has much higher physical instability in comparison with its crystalline counterpart, stabilization of amorphous drugs in a solid-dosage form presents a major challenge to formulators. The currently used approaches for stabilizing amorphous drug are discussed in this article with respect to their preparation, mechanism of stabilization and limitations. In order to realize the potential of amorphous formulations, significant efforts are required to enable the prediction of formulation performance. This will facilitate the development of computational tools that can inform a rapid and rational formulation development process for amorphous drugs.

Photonic Resins: Designing Optical Appearance via Block Copolymer Self-Assembly.

PubMed

Song, Dong-Po; Jacucci, Gianni; Dundar, Feyza; Naik, Aditi; Fei, Hua-Feng; Vignolini, Silvia; Watkins, James J

2018-03-27

Despite a huge variety of methodologies having been proposed to produce photonic structures by self-assembly, the lack of an effective fabrication approach has hindered their practical uses. These approaches are typically limited by the poor control in both optical and mechanical properties. Here we report photonic thermosetting polymeric resins obtained through brush block copolymer (BBCP) self-assembly. We demonstrate that the control of the interplay between order and disorder in the obtained photonic structure offers a powerful tool box for designing the optical appearance of the polymer resins in terms of reflected wavelength and scattering properties. The obtained materials exhibit excellent mechanical properties with hardness up to 172 MPa and Young's modulus over 2.9 GPa, indicating great potential for practical uses as photonic coatings on a variety of surfaces.

Separation of Flame and Nonflame-retardant Plastics Utilizing Magneto-Archimedes Method

NASA Astrophysics Data System (ADS)

Misawa, Kohei; Kobayashi, Takayuki; Mori, Tatsuya; Mishima, Fumihito; Akiyama, Yoko; Nishijima, Shigehiro

2017-07-01

In physical recycling process, the quality of recycled plastics becomes usually poor in case various kinds of plastic materials are mixed. In order to solve the problem, we tried to separate flame and nonflame-retardant plastics used for toner cartridges as one example of mixed plastics by using magneto-Archimedes method. By using this method, we can control levitation and settlement of the particles in the medium by controlling the density and magnetic susceptibility of the medium and the magnetic field. In this study, we introduced the separation system of plastics by the combination of wet type specific gravity separation and magneto-Archimedes separation. In addition, we examined continuous and massive separation by introducing the system which can separate the plastics continuously in the flowing fluid.

Performance of Topological Insulator Interconnects

NASA Astrophysics Data System (ADS)

Philip, Timothy M.; Hirsbrunner, Mark R.; Park, Moon Jip; Gilbert, Matthew J.

2017-01-01

The poor performance of copper interconnects at the nanometer scale calls for new material solutions for continued scaling of integrated circuits. We propose the use of three dimensional time-reversal-invariant topological insulators (TIs), which host backscattering-protected surface states, for this purpose. Using semiclassical methods, we demonstrate that nanoscale TI interconnects have a resistance 1-3 orders of magnitude lower than copper interconnects and graphene nanoribbons at the nanometer scale. We use the nonequilibrium Green function (NEGF) formalism to measure the change in conductance of nanoscale TI and metal interconnects caused by the presence of impurity disorder. We show that metal interconnects suffer a resistance increase, relative to the clean limit, in excess of 500% due to disorder while the TI's surface states increase less than 35% in the same regime.

Chemical Weathering on a Cold and Wet Ancient Mars: New Insights from a Glacial Mars Analog Site

NASA Astrophysics Data System (ADS)

Scudder, N.; Horgan, B. H. N.; Rutledge, A. M.; Rampe, E. B.

2016-12-01

If cold climates prevailed on ancient Mars, we should expect to see corroborating mineralogical evidence preserved in the geologic record. However, the extent to which the diverse alteration mineralogy observed on Mars can be explained by cold climate weathering is currently unknown, as the alteration phases that result from weathering by snow and ice are poorly understood. If cold climate weathering produces distinct alteration signatures, they may be a useful climate indicator on Mars. On Earth, poorly crystalline or short order silicates, such as allophane, tend to dominate in alpine and arctic soils where weathering mainly occurs through rapid seasonal melting of ice and snow. This mineralogy is distinct from the crystalline phyllosilicates that are common in more temperate climates. Thus, we hypothesize that high abundances of poorly crystalline material could indicate cold climate weathering. Here we report new results from a field campaign at the mafic and glaciated Three Sisters volcanic complex in Oregon, USA, to determine the mineralogy and chemistry of cold climate weathering in a Mars analog environment. We find that high abundances of poorly crystalline phases are generated in this environment and that these phases may be detectable using orbital spectroscopy. Ongoing chemical and mineralogical analyses of glacial till and sediments from glacier-fed lakes and streams will allow us to determine the specific distribution and composition of mineral phases in Mars-relevant glacial environments. Poorly crystalline phases have been detected on Mars: modeling of TES data suggests a regionally distributed allophane component, while MER and MSL results indicate up to 40-50% amorphous components in rocks and sediments at Gusev and Gale Craters. We hypothesize that these could be the result of weathering by ice and snow. However, it is not clear that more crystalline alteration phases observed elsewhere on Mars could be formed under a globally cold climate.

Rapid removal of organic micropollutants from water by a porous β-cyclodextrin polymer.

PubMed

Alsbaiee, Alaaeddin; Smith, Brian J; Xiao, Leilei; Ling, Yuhan; Helbling, Damian E; Dichtel, William R

2016-01-14

The global occurrence in water resources of organic micropollutants, such as pesticides and pharmaceuticals, has raised concerns about potential negative effects on aquatic ecosystems and human health. Activated carbons are the most widespread adsorbent materials used to remove organic pollutants from water but they have several deficiencies, including slow pollutant uptake (of the order of hours) and poor removal of many relatively hydrophilic micropollutants. Furthermore, regenerating spent activated carbon is energy intensive (requiring heating to 500-900 degrees Celsius) and does not fully restore performance. Insoluble polymers of β-cyclodextrin, an inexpensive, sustainably produced macrocycle of glucose, are likewise of interest for removing micropollutants from water by means of adsorption. β-cyclodextrin is known to encapsulate pollutants to form well-defined host-guest complexes, but until now cross-linked β-cyclodextrin polymers have had low surface areas and poor removal performance compared to conventional activated carbons. Here we crosslink β-cyclodextrin with rigid aromatic groups, providing a high-surface-area, mesoporous polymer of β-cyclodextrin. It rapidly sequesters a variety of organic micropollutants with adsorption rate constants 15 to 200 times greater than those of activated carbons and non-porous β-cyclodextrin adsorbent materials. In addition, the polymer can be regenerated several times using a mild washing procedure with no loss in performance. Finally, the polymer outperformed a leading activated carbon for the rapid removal of a complex mixture of organic micropollutants at environmentally relevant concentrations. These findings demonstrate the promise of porous cyclodextrin-based polymers for rapid, flow-through water treatment.

Rapid removal of organic micropollutants from water by a porous β-cyclodextrin polymer

NASA Astrophysics Data System (ADS)

Alsbaiee, Alaaeddin; Smith, Brian J.; Xiao, Leilei; Ling, Yuhan; Helbling, Damian E.; Dichtel, William R.

2016-01-01

The global occurrence in water resources of organic micropollutants, such as pesticides and pharmaceuticals, has raised concerns about potential negative effects on aquatic ecosystems and human health. Activated carbons are the most widespread adsorbent materials used to remove organic pollutants from water but they have several deficiencies, including slow pollutant uptake (of the order of hours) and poor removal of many relatively hydrophilic micropollutants. Furthermore, regenerating spent activated carbon is energy intensive (requiring heating to 500-900 degrees Celsius) and does not fully restore performance. Insoluble polymers of β-cyclodextrin, an inexpensive, sustainably produced macrocycle of glucose, are likewise of interest for removing micropollutants from water by means of adsorption. β-cyclodextrin is known to encapsulate pollutants to form well-defined host-guest complexes, but until now cross-linked β-cyclodextrin polymers have had low surface areas and poor removal performance compared to conventional activated carbons. Here we crosslink β-cyclodextrin with rigid aromatic groups, providing a high-surface-area, mesoporous polymer of β-cyclodextrin. It rapidly sequesters a variety of organic micropollutants with adsorption rate constants 15 to 200 times greater than those of activated carbons and non-porous β-cyclodextrin adsorbent materials. In addition, the polymer can be regenerated several times using a mild washing procedure with no loss in performance. Finally, the polymer outperformed a leading activated carbon for the rapid removal of a complex mixture of organic micropollutants at environmentally relevant concentrations. These findings demonstrate the promise of porous cyclodextrin-based polymers for rapid, flow-through water treatment.

Interlayer-expanded molybdenum disulfide nanocomposites for electrochemical magnesium storage.

PubMed

Liang, Yanliang; Yoo, Hyun Deog; Li, Yifei; Shuai, Jing; Calderon, Hector A; Robles Hernandez, Francisco Carlos; Grabow, Lars C; Yao, Yan

2015-03-11

Mg rechargeable batteries (MgRBs) represent a safe and high-energy battery technology but suffer from the lack of suitable cathode materials due to the slow solid-state diffusion of the highly polarizing divalent Mg ion. Previous methods improve performance at the cost of incompatibility with anode/electrolyte and drastic decrease in volumetric energy density. Herein we report interlayer expansion as a general and effective atomic-level lattice engineering approach to transform inactive intercalation hosts into efficient Mg storage materials without introducing adverse side effects. As a proof-of-concept we have combined theory, synthesis, electrochemical measurement, and kinetic analysis to improve Mg diffusion behavior in MoS2, which is a poor Mg transporting material in its pristine form. First-principles simulations suggest that expanded interlayer spacing allows for fast Mg diffusion because of weakened Mg-host interactions. Experimentally, the expansion was realized by inserting a controlled amount of poly(ethylene oxide) into the lattice of MoS2 to increase the interlayer distance from 0.62 nm to up to 1.45 nm. The expansion boosts Mg diffusivity by 2 orders of magnitude, effectively enabling the otherwise barely active MoS2 to approach its theoretical storage capacity as well as to achieve one of the highest rate capabilities among Mg-intercalation materials. The interlayer expansion approach can be leveraged to a wide range of host materials for the storage of various ions, leading to novel intercalation chemistry and opening up new opportunities for the development of advanced materials for next-generation energy storage.

The Use of Miniature Electret Microphones in Small Optoacoustic Cells.

DTIC Science & Technology

1980-06-30

conductivity. The work-horse material has been carnauba wax (used in floor polishes), but shellac, sealing wax , and naphthalene have been used. Such...electret is normally short with large area working faces. * The typical electret material is an organic wax or plastic, a material of poor electrical

40 CFR 725.239 - Use of specific microorganisms in activities conducted outside a structure.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Bradyrhizobium japonicum. (2) Modification of traits. (i) The introduced genetic material must meet the criteria for poorly mobilizable listed in § 725.421(c). (ii) The introduced genetic material must consist only... sequences needed to move genetic material, including linkers, homopolymers, adaptors, transposons, insertion...

40 CFR 725.239 - Use of specific microorganisms in activities conducted outside a structure.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Bradyrhizobium japonicum. (2) Modification of traits. (i) The introduced genetic material must meet the criteria for poorly mobilizable listed in § 725.421(c). (ii) The introduced genetic material must consist only... sequences needed to move genetic material, including linkers, homopolymers, adaptors, transposons, insertion...

40 CFR 725.239 - Use of specific microorganisms in activities conducted outside a structure.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Bradyrhizobium japonicum. (2) Modification of traits. (i) The introduced genetic material must meet the criteria for poorly mobilizable listed in § 725.421(c). (ii) The introduced genetic material must consist only... sequences needed to move genetic material, including linkers, homopolymers, adaptors, transposons, insertion...

Evaluation of different magnetic resonance imaging contrast materials to be used as dummy markers in image-guided brachytherapy for gynecologic malignancies*

PubMed Central

Sales, Camila Pessoa; Carvalho, Heloisa de Andrade; Taverna, Khallil Chaim; Pastorello, Bruno Fraccini; Rubo, Rodrigo Augusto; Borgonovi, Arthur Felipe; Stuart, Silvia Radwanski; Rodrigues, Laura Natal

2016-01-01

Objective To identify a contrast material that could be used as a dummy marker for magnetic resonance imaging. Materials and Methods Magnetic resonance images were acquired with six different catheter-filling materials-water, glucose 50%, saline, olive oil, glycerin, and copper sulfate (CuSO4) water solution (2.08 g/L)-inserted into compatible computed tomography/magnetic resonance imaging ring applicators placed in a phantom made of gelatin and CuSO4. The best contrast media were tested in four patients with the applicators in place. Results In T2-weighted sequences, the best contrast was achieved with the CuSO4-filled catheters, followed by saline- and glycerin-filled catheters, which presented poor visualization. In addition (also in T2-weighted sequences), CuSO4 presented better contrast when tested in the phantom than when tested in the patients, in which it provided some contrast but with poor identification of the first dwell position, mainly in the ring. Conclusion We found CuSO4 to be the best solution for visualization of the applicator channels, mainly in T2-weighted images in vitro, although the materials tested presented low signal intensity in the images obtained in vivo, as well as poor precision in determining the first dwell position. PMID:27403016

A Study of Poor Black Children Who Are Successful Readers. Reading Education Report No. 33.

ERIC Educational Resources Information Center

Durkin, Dolores

A study was conducted to acquire information about poor black children who were successful readers in order to determine what can be done to increase the number of such children. For purposes of the study, "successful" was defined as scoring at or above grade level on a standardized reading test at the end of fifth grade, while "poor" was defined…

Infrared preheating to improve interlayer strength of big area additive manufacturing (BAAM) components

DOE PAGES

Kishore, Vidya; Ajinjeru, Christine; Nycz, Andrzej; ...

2017-03-01

The Big Area Additive Manufacturing (BAAM) system can print structures on the order of several meters at high extrusion rates, thereby having the potential to significantly impact automotive, aerospace and energy sectors. The functional use of such parts, however, may be limited by mechanical anisotropy in which the strength of printed parts across successive layers in the build direction (z-direction) is significantly lower than the corresponding in-plane strength (x-y directions). This has been primarily attributed to poor bonding between printed layers as the lower layers cool below the glass transition temperature (Tg) before the next layer is deposited. Therefore, themore » potential of using infrared heating is considered for increasing the surface temperature of the printed layer just prior to deposition of new material to improve the interlayer strength of the components. This study found significant improvements in bond strength for the deposition of acrylonitrile butadiene styrene (ABS) reinforced with 20% chopped carbon fiber when the surface temperature of the substrate material was increased from below Tg to close to or above Tg using infrared heating.« less

Thermomechanical properties and fracture of resin-bonded-sand cores - Experimental study and application in aluminium foundry

NASA Astrophysics Data System (ADS)

Menet, Claire; Reynaud, Pascal; Fantozzi, Gilbert; Thibault, Delphine; Laforêt, Adrien

2017-06-01

Sand cores are used to produce internal cavities of metallic cast parts with complex shapes like automotive cylinder heads. Foundry cores are granular materials made of sand grains aggregated with binder bridges. In the cold box coring process, the binder is a polyurethane resin. It is noteworthy that during the casting of the liquid metal, the polymer binder is seriously damaged. This kind of materials has been poorly investigated so far. This study aims for a better understanding of the mechanical behaviour and fracture of cores subjected to various loads and thermal ageing. Particularly, the focus is on the decoring step, which consists in removing the sand by hammering and vibration of the metallic part after casting. This major project, generated from the collaboration of the aluminum casting company Montupet, and two laboratories Centre des Matériaux (CdM) and MATEIS, includes both experimental and numerical activities in order to model the decoring step of cylinder heads based on empiric data. Here, the experimental part of the work is presented.

Infrared preheating to improve interlayer strength of big area additive manufacturing (BAAM) components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kishore, Vidya; Ajinjeru, Christine; Nycz, Andrzej

The Big Area Additive Manufacturing (BAAM) system can print structures on the order of several meters at high extrusion rates, thereby having the potential to significantly impact automotive, aerospace and energy sectors. The functional use of such parts, however, may be limited by mechanical anisotropy in which the strength of printed parts across successive layers in the build direction (z-direction) is significantly lower than the corresponding in-plane strength (x-y directions). This has been primarily attributed to poor bonding between printed layers as the lower layers cool below the glass transition temperature (Tg) before the next layer is deposited. Therefore, themore » potential of using infrared heating is considered for increasing the surface temperature of the printed layer just prior to deposition of new material to improve the interlayer strength of the components. This study found significant improvements in bond strength for the deposition of acrylonitrile butadiene styrene (ABS) reinforced with 20% chopped carbon fiber when the surface temperature of the substrate material was increased from below Tg to close to or above Tg using infrared heating.« less

Synthesis and evaluation of functional alginate hydrogels based on click chemistry for drug delivery applications.

PubMed

García-Astrain, Clara; Avérous, Luc

2018-06-15

Environment-sensitive alginate-based hydrogels for drug delivery applications are receiving increasing attention. However, most work in this field involves traditional cross-linking strategies which led to hydrogels with poor long-term stability. Herein, a series of chemically cross-linked alginate hydrogels was synthesized via click chemistry using Diels-Alder reaction by reacting furan-modified alginate and bifunctional cross-linkers. Alginate was successfully functionalized with furfurylamine. Then, 3D architectures were synthesized with water-soluble bismaleimides. Different substitution degrees were achieved in order to study the effect of alginate modification and the cross-linking extent over the behaviour of the hydrogels. The ensuing hydrogels were analysed in terms of microstructure, swelling, structure modification and rheological behaviour. The materials response to external stimuli such as pH was also investigated, revealing a pulsatile behaviour in a large pH range (1-13) and a clear pH-dependent swelling. Finally, vanillin release studies were conducted to demonstrate the potential of these biobased materials for drug delivery applications. Copyright © 2018 Elsevier Ltd. All rights reserved.

Reuse of Boron Waste as an Additive in Road Base Material

PubMed Central

Zhang, Yutong; Guo, Qinglin; Li, Lili; Jiang, Ping; Jiao, Yubo; Cheng, Yongchun

2016-01-01

The amount of boron waste increases year by year. There is an urgent demand to manage it in order to reduce the environmental impact. In this paper, boron waste was reused as an additive in road base material. Lime and cement were employed to stabilize the waste mixture. Mechanical performances of stabilized mixture were evaluated by experimental methods. A compaction test, an unconfined compressive test, an indirect tensile test, a modulus test, a drying shrinkage test, and a frost resistance test were carried out. Results indicated that mechanical strengths of lime-stabilized boron waste mixture (LSB) satisfy the requirements of road base when lime content is greater than 8%. LSB can only be applied in non-frozen regions as a result of its poor frost resistance. The lime–cement-stabilized mixture can be used in frozen regions when lime and cement contents are 8% and 5%, respectively. Aggregate reduces the drying shrinkage coefficient effectively. Thus, aggregate is suggested for mixture stabilization properly. This work provides a proposal for the management of boron waste. PMID:28773539

Electrochemical properties of Sn/C nanoparticles fabricated by redox treatment and pulsed wire evaporation method

NASA Astrophysics Data System (ADS)

Song, Ju-Seok; Cho, Gyu-Bong; Ahn, Jou-Hyeon; Cho, Kwon-Koo

2017-09-01

Tin (Sn) based anode materials are the most promising anode materials for lithium-ion batteries due to their high theoretical capacity corresponding to the formation of Li4.4Sn composition (Li4.4Sn, 994 mAh/g). However, the applications of tin based anodes to lithium-ion battery system are generally limited by a large volume change (>260%) during lithiation and delithiation cycle, which causes pulverize and poor cycling stability. In order to overcome this shortcoming, we fabricate a Sn/C nanoparticle with a yolk-shell structure (Sn/void/C) by using pulsed wire evaporation process and oxidation/reduction heat treatment. Sn nanoparticles are encapsulated by a conductive carbon layer with structural buffer that leaves enough room for expansion and contraction during lithium insertion/desertion. We expect that the yolk-shell structure has the ability to accommodate the volume changes of tin and leading to an improved cycle performance. The Sn/Void/C anode with yolk-shell structure shows a high specific capacity of 760 mAh/g after 50 cycles.

Benzodiazepine Scaffold as Drug-like Molecular Simplification of FR235222: A Chemical Tool for Exploring HDAC Inhibition.

PubMed

Randino, Rosario; Moronese, Ilaria; Cini, Elena; Bizzarro, Valentina; Persico, Marco; Grimaldi, Manuela; Scrima, Mario; D'Ursi, Anna Maria; Novellino, Ettore; Sobarzo-Sanchez, Eduardo; Rastrelli, Luca; Fattorusso, Caterina; Petrella, Antonello; Rodriquez, Manuela; Taddei, Maurizio

2017-01-01

Synthesis, computational study and biological evaluation of peptidomimetic analogues of FR235222 (3), a natural immunosuppressant and HDAC inhibitor, have been reported. These new compounds, bearing α-hydroxyketone moiety, as more stable zinc binding group (ZBG), were evaluated in vitro as HDAC inhibitors against the human HDACs isoforms 1-9 and in cellular antiproliferative assays on U937 human leukemia cell line. The 1,4-benzodiazepin-2,5-dione (BDZ), capping group and the natural ZBG, (S,R)-2-amino-9-hydroxy-8-oxodecanoic acid (Ahoda), were evaluated in order to probe HDAC inhibition and/or paralogue selectivity. Some of the new derivatives showed an interesting activity against a number of HDAC isozymes. The observed activity profile was rationalized by a computational assisted SAR study, in order to understand how the BDZ classes interact with the enzyme into the catalytic pocket. Despite its poor solubility, compound 17b showed significant antiproliferative profile and HDAC inhibition activity. In order to assess how the solubility issue could have affected the biological outcome, bioassay conditions were reproduced and quantification of precipitated particulate material was evaluated by turbidimetric and NMR studies together with physicochemical descriptors prediction. Thus, BDZ 17b has been chosen to be promising lead compounds for further optimization, in order to elucidate molecule- enzyme surface recognition.

Space missions for SETI.

PubMed

Drake, F

1999-01-01

Radio Telescopes for SETI searches are less demanding than general purpose astronomical radio telescopes. This provides an opportunity to exploit economical approaches in designing SETI systems. Radio Telescopes in low Earth orbit offer no discernible advantages to SETI; indeed, they probably would perform more poorly than a telescope in any other location. Telescopes in geosynchronous orbits would be sufficiently far from Earth to mitigate greatly the deleterious effect of human radio transmissions. Telescopes on the far side of the moon would be superb both from a radio interference standpoint, and from a civil engineering standpoint. Single-reflector telescopes as large as 50 kilometers in diameter could be constructed with conventional materials. However, their costs appear prohibitive. The asteroid belt and the outer solar system are unpromising places to place a large radio telescope. Perhaps the ultimate radio telescope would utilize the sun as a gravitational lens, focusing radiation on free-flying 10-meter class or possibly larger radio telescopes located at distances of the order of 1000 A.U. from the sun. Such a combination has an energy collecting area at 10 centimeters wavelength equivalent to that of a radio telescope about 11 kilometers in diameter, or of the order of 3000 Arecibo radio telescopes. Such a system could detect transmitters with EIRP of the order of a gigawatt at a distance of the order of the distance to the galactic center.

Interactions and Survival of Enteric Viruses in Soil Materials

PubMed Central

Sobsey, Mark D.; Dean, Cheryl H.; Knuckles, Maurice E.; Wagner, Ray A.

1980-01-01

There were marked differences in the abilities of eight different soil materials to remove and retain viruses from settled sewage, but for each soil material the behavior of two different viruses, poliovirus type 1 and reovirus type 3, was often similar. Virus adsorption to soil materials was rapid, the majority occurring within 15 min. Clayey materials efficiently adsorbed both viruses from wastewater over a range of pH and total dissolved solids levels. Sands and organic soil materials were comparatively poor adsorbents, but in some cases their ability to adsorb viruses increased at low pH and with the addition of total dissolved solids or divalent cations. Viruses in suspensions of soil material in settled sewage survived for considerable time periods, despite microbial activity. In some cases virus survival was prolonged in suspensions of soil materials compared to soil-free controls. Although sandy and organic soil materials were poor virus adsorbents when suspended in wastewater, they gave ≥95% virus removal from intermittently applied wastewater as unsaturated, 10-cm-deep columns. However, considerable quantities of the retained viruses were washed from the columns by simulated rainfall. Under the same conditions, clayey soil material removed ≥99.9995% of the viruses from applied wastewater, and none were washed from the columns by simulated rainfall. PMID:6250478

A novel multiple batch extraction test to assess contaminant mobilization from porous waste materials

NASA Astrophysics Data System (ADS)

Iden, S. C.; Durner, W.; Delay, M.; Frimmel, F. H.

2009-04-01

Contaminated porous materials, like soils, dredged sediments or waste materials must be tested before they can be used as filling materials in order to minimize the risk of groundwater pollution. We applied a multiple batch extraction test at varying liquid-to-solid (L/S) ratios to a demolition waste material and a municipal waste incineration product and investigated the release of chloride, sulphate, sodium, copper, chromium and dissolved organic carbon from both waste materials. The liquid phase test concentrations were used to estimate parameters of a relatively simple mass balance model accounting for equilibrium partitioning. The model parameters were estimated within a Bayesian framework by applying an efficient MCMC sampler and the uncertainties of the model parameters and model predictions were quantified. We tested isotherms of the linear, Freundlich and Langmuir type and selected the optimal isotherm model by use of the Deviance Information Criterion (DIC). Both the excellent fit to the experimental data and a comparison between the model-predicted and independently measured concentrations at the L/S ratios of 0.25 and 0.5 L/kg demonstrate the applicability of the model for almost all studied substances and both waste materials. We conclude that batch extraction tests at varying L/S ratios provide, at moderate experimental cost, a powerful complement to established test designs like column leaching or single batch extraction tests. The method constitutes an important tool in risk assessments, because concentrations at soil water contents representative for the field situation can be predicted from easier-to-obtain test concentrations at larger L/S ratios. This helps to circumvent the experimental difficulties of the soil saturation extract and eliminates the need to apply statistical approaches to predict such representative concentrations which have been shown to suffer dramatically from poor correlations.

Harmonization in laboratory medicine: Requests, samples, measurements and reports.

PubMed

Plebani, Mario

2016-01-01

In laboratory medicine, the terms "standardization" and "harmonization" are frequently used interchangeably as the final goal is the same: the equivalence of measurement results among different routine measurement procedures over time and space according to defined analytical and clinical quality specifications. However, the terms define two distinct, albeit closely linked, concepts based on traceability principles. The word "standardization" is used when results for a measurement are equivalent and traceable to the International System of Units (SI) through a high-order primary reference material and/or a reference measurement procedure (RMP). "Harmonization" is generally used when results are equivalent, but neither a high-order primary reference material nor a reference measurement procedure is available. Harmonization is a fundamental aspect of quality in laboratory medicine as its ultimate goal is to improve patient outcomes through the provision of accurate and actionable laboratory information. Patients, clinicians and other healthcare professionals assume that clinical laboratory tests performed by different laboratories at different times on the same sample and specimen can be compared, and that results can be reliably and consistently interpreted. Unfortunately, this is not necessarily the case, because many laboratory test results are still highly variable and poorly standardized and harmonized. Although the initial focus was mainly on harmonizing and standardizing analytical processes and methods, the scope of harmonization now also includes all other aspects of the total testing process (TTP), such as terminology and units, report formats, reference intervals and decision limits as well as tests and test profiles, requests and criteria for interpretation. Several projects and initiatives aiming to improve standardization and harmonization in the testing process are now underway. Laboratory professionals should therefore step up their efforts to provide interchangeable and comparable laboratory information in order to ultimately assure better diagnosis and treatment in patient care.

Metal segregation in hierarchically structured cathode materials for high-energy lithium batteries

DOE PAGES

Lin, Feng; Xin, Huolin L.; Nordlund, Dennis; ...

2016-01-11

Controlling surface and interfacial properties of battery materials is key to improving performance in rechargeable Li-ion devices. Surface reconstruction from a layered to a rock salt structure in metal oxide cathode materials is commonly observed and results in poor high-voltage cycling performance, impeding attempts to improve energy density. Hierarchically structured LiNi 0.4Mn 0.4Co 0.2O 2 (NMC-442) spherical powders, made by spray pyrolysis, exhibit local elemental distribution gradients that deviate from the global NMC-442 composition; specifically, they are Ni-rich and Mn-poor at particle surfaces. These materials demonstrate improved Coulombic efficiencies, discharge capacities, and high-voltage capacity retention in lithium half-cell configurations. Themore » subject powders show superior resistance against surface reconstruction due to the tailored surface chemistry, compared to conventional NMC-442 materials. This paves the way towards the development of a new generation of robust and stable high-energy NMC cathodes for Li-ion batteries.« less

Apollo 17 materials viewed from 2 to 4 mm soil particles: Pre-serenitatis highlands components

NASA Technical Reports Server (NTRS)

Jolliff, Bradley L.; Bishop, Kaylynn M.

1993-01-01

Among the highland lithologies of 2-4 mm rock fragments in North Massif soil 76503, we have found a compositional group, low in incompatible element concentrations, that we interpret as representing the pre-Serenitatis surface. A component of these materials is an igneous-textured lithology that we believe formed in large impact melts. These are compositionally similar to, and possibly precursors of, many of the granulitic breccias that appear to be mixtures of ferroan and magnesian-suite rocks. The polymict, or old, upper-crustal breccias, along with granulitic breccias and the endogenous igneous lithologies found particularly at the North Massif stations, constitute the poorly consolidated portions of North Massif. Highland samples from the South Massif, on the other hand, are enriched in materials of the competent, impact-melt breccias formed by the Serenitatis impact. The competent melt-breccias contain clasts of most of the pre-existing surface materials, but they also contain components not found in the rocks of the poorly consolidated massif materials.

Effect of Vertical Concentration Gradient on Globally Planar Detonation with Detailed Reaction Mechanism

NASA Astrophysics Data System (ADS)

Song, Qingguana; Wang, Cheng; Han, Yong; Gao, Dayuan; Duan, Yingliang

2017-06-01

Since detonation often initiates and propagates in the non-homogeneous mixtures, investigating its behavior in non-uniform mixtures is significant not only for the industrial explosion in the leakage combustible gas, but also for the experimental investigations with a vertical concentration gradient caused by the difference in the molecular weight of gas mixture. Objective of this work is to show the detonation behavior in the mixture with different concentration gradients with detailed chemical reaction mechanism. A globally planar detonation in H2-O2 system is simulated by a high-resolution code based on the fifth-order weighted essentially non-oscillatory (WENO) scheme in spatial discretization and the third-order Additive Runge-Kutta schemes in time discretization. The different shocked combustion modes appear in the rich-fuel and poor-fuel layers due to the concentration gradient effect. Globally, for the cases with the lower gradient detonation can be sustained in a way of the alternation of the multi-heads mode and single-head mode, whereas for the cases with the higher gradient detonation propagates with a single-head mode. Institute of Chemical Materials, CAEP.

Morin Flavonoid Adsorbed on Mesoporous Silica, a Novel Antioxidant Nanomaterial

PubMed Central

Arriagada, Francisco; Correa, Olosmira; Günther, Germán; Nonell, Santi; Mura, Francisco; Olea-Azar, Claudio

2016-01-01

Morin (2´,3, 4´,5,7-pentahydroxyflavone) is a flavonoid with several beneficial health effects. However, its poor water solubility and it sensitivity to several environmental factors avoid its use in applications like pharmaceutical and cosmetic. In this work, we synthetized morin-modified mesoporous silica nanoparticles (AMSNPs-MOR) as useful material to be used as potential nanoantioxidant. To achieve this, we characterized its adsorption kinetics, isotherm and the antioxidant capacity as hydroxyl radical (HO•) scavenger and singlet oxygen (1O2) quencher. The experimental data could be well fitted with Langmuir, Freundlich and Temkin isotherm models, besides the pseudo-second order kinetics model. The total quenching rate constant obtained for singlet oxygen deactivation by AMSNPs-MOR was one order of magnitude lower than the morin rate constant reported previously in neat solvents and lipid membranes. The AMSNPs-MOR have good antioxidant properties by itself and exhibit a synergic effect with morin on the antioxidant property against hydroxyl radical. This effect, in the range of concentrations studied, was increased when the amount of morin adsorbed increased. PMID:27812111

Tooth and bone deformation: structure and material properties by ESPI

NASA Astrophysics Data System (ADS)

Zaslansky, Paul; Shahar, Ron; Barak, Meir M.; Friesem, Asher A.; Weiner, Steve

2006-08-01

In order to understand complex-hierarchical biomaterials such as bones and teeth, it is necessary to relate their structure and mechanical-properties. We have adapted electronic speckle pattern-correlation interferometry (ESPI) to make measurements of deformation of small water-immersed specimens of teeth and bones. By combining full-field ESPI with precision mechanical loading we mapped sub-micron displacements and determined material-properties of the samples. By gradually and elastically compressing the samples, we compensate for poor S/N-ratios and displacement differences of about 100nm were reliably determined along samples just 2~3mm long. We produced stress-strain curves well within the elastic performance range of these materials under biologically relevant conditions. For human tooth-dentin, Young's modulus in inter-dental areas of the root is 40% higher than on the outer sides. For cubic equine bone samples the compression modulus of axial orientations is about double the modulus of radial and tangential orientations (20 GPa versus 10 GPa respectively). Furthermore, we measured and reproduced a surprisingly low Poisson's ratio, which averaged about 0.1. Thus the non-contact and non-destructive measurements by ESPI produce high sensitivity analyses of mechanical properties of mineralized tissues. This paves the way for mapping deformation-differences of various regions of bones, teeth and other biomaterials.

Municipal solid waste system analysis through energy consumption and return approach.

PubMed

Tomić, Tihomir; Schneider, Daniel Rolph

2017-12-01

Inappropriate waste management and poor resource efficiency are two of the biggest problems which European Union is trying to solve through Landfill Directive, Waste Framework Directive and Circular Economy Package by increasing recycling and reuse and reducing waste disposal. In order to meet set goals, new European Union member states must quickly change national legislature and implement appropriate solutions. In the circumstances of strong EU resource and energy dependence, decision makers need to analyse which of the considered waste management systems leads to higher overall benefits ie. which is more sustainable. The main problem in this kind of analysis is a wide range of possible technologies and the difference in inputs and outputs. Sustainability of these systems is analysed through single-score LCA based assessment, using primary energy used to produce materials and energy vectors as a common measure. To ensure reliable results, interoperability between different data sources and material flows of waste and its components are monitored. Tracking external and internal material, and energy flows enable modelling of mutual interactions between different facilities. Resulting PERI, primary energy return based index, is used for comparison of different waste management scenarios. Results show that time and legislation dependent changes have great influence on decision making related to waste management and interconnected systems. Copyright © 2017 Elsevier Ltd. All rights reserved.

Explaining the impact of poverty on old-age frailty in Europe: material, psychosocial and behavioural factors.

PubMed

Stolz, Erwin; Mayerl, Hannes; Waxenegger, Anja; Freidl, Wolfgang

2017-12-01

Previous research found poverty to be associated with adverse health outcomes among older adults but the factors that translate low economic resources into poor physical health are not well understood. The goal of this analysis was to assess the impact of material, psychosocial, and behavioural factors as well as education in explaining the poverty-health link. In total, 28 360 observations from 11 390 community-dwelling respondents (65+) in the Survey of Health, Ageing and Retirement in Europe (2004-13, 10 countries) were analysed. Multilevel growth curve models were used to assess the impact of combined income and asset poverty risk on old-age frailty (frailty index) and associated pathway variables. In total, 61.8% of the variation of poverty risk on frailty level was explained by direct and indirect effects. Results stress the role of material and particularly psychosocial factors such as perceived control and social isolation, whereas the role of health behaviour was negligible. We suggest to strengthen social policy and public health efforts in order to fight poverty and its deleterious health effects from early age on as well as to broaden the scope of interventions with regard to psychosocial factors. © The Author 2017. Published by Oxford University Press on behalf of the European Public Health Association. All rights reserved.

Poor, Rural Neighborhoods and Early School Achievement.

ERIC Educational Resources Information Center

Bickel, Robert; Smith, Cynthia; Eagle, Teresa Hardman

A study sought to identify the existence of neighborhood effects on school achievement that are independent of social class and family background among students from poor, rural neighborhoods. Ethnographic material yielded a concept of rural West Virginia neighborhoods in which residents expect their encounters to be friendly, informal, almost…

Deficits in verbal long-term memory and learning in children with poor phonological short-term memory skills.

PubMed

Gathercole, Susan E; Briscoe, Josie; Thorn, Annabel; Tiffany, Claire

2008-03-01

Possible links between phonological short-term memory and both longer term memory and learning in 8-year-old children were investigated in this study. Performance on a range of tests of long-term memory and learning was compared for a group of 16 children with poor phonological short-term memory skills and a comparison group of children of the same age with matched nonverbal reasoning abilities but memory scores in the average range. The low-phonological-memory group were impaired on longer term memory and learning tasks that taxed memory for arbitrary verbal material such as names and nonwords. However, the two groups performed at comparable levels on tasks requiring the retention of visuo-spatial information and of meaningful material and at carrying out prospective memory tasks in which the children were asked to carry out actions at a future point in time. The results are consistent with the view that poor short-term memory function impairs the longer-term retention and ease of learning of novel verbal material.

On-site characterisation, re-packaging and transport of luminised, former aircraft escape hatches

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reeves, Nigel; John, Gordon; Beadle, Ian

2007-07-01

AMEC NNC, under contract to the UK Environment Agency, recovered a number of redundant aircraft hatches from an insecure location in North Wales. The Environment Agency instigated emergency action under the Radioactive Substances Act 1993 (RSA93), to recover the hatches. Section 30(1) of RSA93 gives the Environment Agency powers to dispose of radioactive waste where it is unlikely the waste will be lawfully disposed of. Funding for this project was provided by the UK Government, within the Surplus Source Disposal Programme. The Environment Agency worked closely with partner regulatory organisations including the Health and Safety Executive (HSE), the Department formore » Transport (DfT) and the Local Authority to ensure the safe packaging, removal and transport of the material to a part-shielded store pending final disposal. The project comprised a number of technical difficulties that needed to be overcome. These included poor existing characterisation of the waste, insecure premises requiring daily lock-down, construction of a temporary containment facility with associated filtered extract and the inclement weather. AMEC NNC's initial risk assessment identified the likelihood of high levels of loose, airborne radiological material. In order to provide adequate protection for personnel, and to prevent the spread of any radioactive contamination, the decision was made to implement radiological containment and to equip contractors with appropriate RPE (Respiratory Protective Equipment). Accurate characterisation of the radiological nature of the material was a crucial objective within the project. This was in order to correctly identify the Proper Shipping Name for consignment for transport, and to ensure that suitable transport containers were used. The packaged wastes were then transported to a secure location for temporary storage prior to final disposal. An innovative route was identified for processing of this material. Beneficial recycling and re-use within the nuclear industry was the outcome. (authors)« less

Zero-order release of poorly water-soluble drug from polymeric films made via aqueous slurry casting.

PubMed

Zhang, Lu; Alfano, Joy; Race, Doran; Davé, Rajesh N

2018-05-30

In spite of significant recent interest in polymeric films containing poorly water-soluble drugs, dissolution mechanism of thicker films has not been investigated. Consequently, release mechanisms of poorly water-soluble drugs from thicker hydroxypropyl methylcellulose (HPMC) films are investigated, including assessing thickness above which they exhibit zero-order drug release. Micronized, surface modified particles of griseofulvin, a model drug of BSC class II, were incorporated into aqueous slurry-cast films of different thicknesses (100, 500, 1000, 1500 and 2000 μm). Films 1000 μm and thicker were formed by either stacking two or more layers of ~500 μm, or forming a monolithic thick film. Compared to monolithic thick films, stacked films required simpler manufacturing process (easier casting, short drying time) and resulted in better critical quality attributes (appearance, uniformity of thickness and drug per unit area). Both the film forming approaches exhibited similar release profiles and followed the semi-empirical power law. As thickness increased from 100 μm to 2000 μm, the release mechanism changed from Fickian diffusion to zero-order release for films ≥1000 μm. The diffusional power law exponent, n, achieved value of 1, confirming zero-order release, whereas the percentage drug release varied linearly with sample surface area, and sample thickness due to fixed sample diameter. Thus, multi-layer hydrophilic polymer aqueous slurry-cast thick films containing poorly water-soluble drug particles provide a convenient dosage form capable of zero-order drug release with release time modulated through number of layers. Copyright © 2018 Elsevier B.V. All rights reserved.

Heat transfer enhancement in a lithium-ion cell through improved material-level thermal transport

NASA Astrophysics Data System (ADS)

Vishwakarma, Vivek; Waghela, Chirag; Wei, Zi; Prasher, Ravi; Nagpure, Shrikant C.; Li, Jianlin; Liu, Fuqiang; Daniel, Claus; Jain, Ankur

2015-12-01

While Li-ion cells offer excellent electrochemical performance for several applications including electric vehicles, they also exhibit poor thermal transport characteristics, resulting in reduced performance, overheating and thermal runaway. Inadequate heat removal from Li-ion cells originates from poor thermal conductivity within the cell. This paper identifies the rate-limiting material-level process that dominates overall thermal conduction in a Li-ion cell. Results indicate that thermal characteristics of a Li-ion cell are largely dominated by heat transfer across the cathode-separator interface rather than heat transfer through the materials themselves. This interfacial thermal resistance contributes around 88% of total thermal resistance in the cell. Measured value of interfacial resistance is close to that obtained from theoretical models that account for weak adhesion and large acoustic mismatch between cathode and separator. Further, to address this problem, an amine-based chemical bridging of the interface is carried out. This is shown to result in in four-times lower interfacial thermal resistance without deterioration in electrochemical performance, thereby increasing effective thermal conductivity by three-fold. This improvement is expected to reduce peak temperature rise during operation by 60%. By identifying and addressing the material-level root cause of poor thermal transport in Li-ion cells, this work may contributes towards improved thermal performance of Li-ion cells.

New Comparative Measures of Income, Material Deprivation, and Well-Being

ERIC Educational Resources Information Center

Smeeding, Timothy M.

2009-01-01

Most societies, rich and poor, seek to measure progress in reducing poverty and need, as indicated by material deprivation or social exclusion. The yardsticks used to assess progress and policy impact mainly include income-based poverty, but broader measures of poverty based on consumption, wealth, and material deprivation are also now coming into…

Protecting tree roots and subterranean infrastructure in urban areas by developing self-compacting flowable fills with root growth impeding properties

NASA Astrophysics Data System (ADS)

Felde, Vincent; Simon, Jana; Kimm-Friedenberg, Stefan; Peth, Stephan; Middendorf, Bernhard

2015-04-01

In urban areas, the installation of cables and disposal lines is still done by open building method. Here, a ditch is being excavated, pipes and lines are laid and subsequently it is filled with and covered by bulk material (e.g. sand or gravel), which is then compacted. Due to the often times limited space that the roots have in the ground and the better supply of water and oxygen in the poorly compacted bulk material, these refilled ditches are areas of preferential root growth of urban trees. The entangling of the pipes and supply lines by these roots leads to severe damage of the tree when maintenance work on the lines is carried out and roots have to be cut. In order to reduce this competition between urban trees and urban subterranean infrastructure, the development of a self-compacting flowable fill with root growth resistance is mandatory. Physico-chemical properties, such as a very high pH-value and a low cation-exchange-capacity, a low root-penetrability, a high packing density and a low porosity, with a poorly connected pore system that impedes gas and water exchange are the characteristic aspects of this flowable fills that could help avoid undesired root penetration into supply lines. The flowable fills are supposed to sheath pipes and lines void-free and without any tension, in order to restrain the root growth in these areas. Trees are of crucial importance for urban ecosystems and are comprising 3% of the total stock of trees in the Federal Republic of Germany, which is why it is fundamental to conserve them. This work therefore targets not only at enabling a balanced coexistence of urban trees and subterranean infrastructure, but also at avoiding costly re-opening of ditches, tree harming cutting of roots and time consuming maintenance work. Further positive side effects are reduced costs for network providers and local municipalities, as well as reduced noise and dust emissions for passersby and local residents. To guarantee the root growth restricting properties, the self-compacting fill has to have less porosity than the adjacent soil (40 - 60%). Theoretically a porosity of 30% is possible with a homogeneous compaction of sand. In urban areas, however, because of the limited spaces and crossing pipes, a mechanical and homogenous compacting is often impossible. Porosities of 60 to 70% are the result. Self-compacting flowable fills have a porosity of about 40% while the first optimized materials can even have a porosity of 28%. We present the first results of the hydro-mechanical properties of the different materials under development that highlight the influence of the mixture of the fills (i.e. maximal grain size) on the root growth impeding properties, while still ensuring mechanical workability of the material (in spite of the low porosity, strengths less than 0.8 N mm-² must be ensured at all times).

Redescription of poorly known species of Ceratothoa Dana, 1852 (Crustacea, Isopoda, Cymothoidae), based on original type material

PubMed Central

Hadfield, Kerry A.; Bruce, Niel L.; Smit, Nico J.

2016-01-01

Abstract Due to the difficulty in accurately identifying cymothoids, these parasitic isopods are often incorrectly named or confused with other species. Within the genus Ceratothoa, a number of recent studies have aimed at clarifying some of the problematic species; however, several of the less studied species still require revision. This paper redescribes, from type material, several poorly known Ceratothoa species including Ceratothoa angulata, Ceratothoa capri, Ceratothoa carinata, Ceratothoa collaris, Ceratothoa gilberti, Ceratothoa gobii, Ceratothoa guttata, Ceratothoa italica, Ceratothoa oestroides, and Ceratothoa verrucosa, further resolving taxonomic uncertainties within the genus. PMID:27408544

μ SR studies of the extended kagome systems YBaCo4O7+δ (δ = 0 and 0.1)

NASA Astrophysics Data System (ADS)

Lee, Suheon; Lee, Wonjun; Mitchell, John; Choi, Kwang-Yong

We present a μSR study of the extended kagome systems YBaCo4O7+δ (δ = 0 and 0.1), which are made up of an alternating stacking of triangular and kagome layers. The parent material YBaCo4O7.0 undergoes a structural phase transition at 310 K, releasing geometrical frustration and thereby stabilizing an antiferromagnetically ordered state below TN = 106 K. The μSR spectra of YBaCo4O7.0 exhibit the loss of initial asymmetry and the development of a fast relaxation component below TN = 111 K. This indicates that the Co spins in the kagome planes remain in an inhomogeneous and dynamically fluctuating state down to 4 K, while the triangular spins order antiferromagnetically below TN. The nonstoichiometric YBaCo4O7.1 compound with no magnetic ordering exhibits a disparate spin dynamics between the fast cooling (10 K/min) and slow cooling (1 K/min) procedures. While the fast-cooled μSR spectra show a simple exponential decay, the slow-cooled spectra are described with a sum of a simple exponential function and a stretched exponential function. These are in agreements with the occurrence of the phase separation between interstitial oxygen-rich and poor regions in the slow-cooling measurements.

A novel solubility-modulated granules through porosity osmotic pump for controlled carvedilol delivery.

PubMed

Song, Qun-Li; Li, Ping; Li, Yu-Min

2012-01-01

A method for the preparation of porosity osmotic pump granules was obtained by modulating carvedilol solubility with tartaric acid. Controlled porosity of the membrane was accomplished by the use of pore-forming agent in the coating. In this study, carvedilol was chosen as a model drug with an aim to develop a zero-order release system; tartaric acid was used as the solubility promoter; NaCl was used as the osmotic agent; cellulose acetate (CA) was used as the materials of semipermeable membrane; and PEG-400 was used as the pore-forming agent in the semipermeable membrane. The influence of different factors or levels on the in vitro release was studied. In order to simulate the gastrointestinal tract environments, two kinds of pH media (pH 1.5 and 6.8) on drug release were studied in this research, respectively. This porosity osmotic pump was optimized by single factor design experiments, and it was found to deliver carvedilol at a zero-order rate within 12 h and controlled release for 24 h. We drew a conclusion that the solubility-modulated porosity osmotic pump system is simple to prepare and might be used for the preparation of osmotic pump system of other poorly water-soluble drugs with alkaline or acid groups.

Repeatability of testing procedures for resilient modulus and fatigue.

DOT National Transportation Integrated Search

1989-04-01

Extensive use of diametral resilient modulus and fatigue testing is made by the Oregon State Highway Division to evaluate asphaltic concrete materials. Test results on similar materials (e.g., adjacent field cores), however, often indicate a poor lev...

Biocompatibility assessment of synthetic sling materials for female stress urinary incontinence.

PubMed

Gomelsky, Alex; Dmochowski, Roger R

2007-10-01

We evaluated the performance and complications of currently available synthetic sling materials with a focus on in vitro and in vivo biocompatibility, and acceptance in the human body. We reviewed the MEDLINE database for relevant literature pertaining to various synthetic sling materials. The Food and Drug Administration regulations regarding the regulation and biocompatibility testing of synthetic meshes were also reviewed. Many synthetic meshes used for sling construction were introduced before rigorous Food and Drug Administration regulations were passed and, thus, some became associated with unique complications. Most meshes used in pubovaginal and mid urethral sling surgery are associated with high short-term success rates and relatively few intraoperative complications. Despite modifications and additives, slings constructed from polytetrafluoroethylene and polyethylene are poorly accepted by the human body. Flexible, macroporous, polypropylene meshes appear to integrate more completely with human tissue than other synthetic materials. However, multifilament and nonknitted polypropylene slings may integrate poorly. The composition, weave and pore size of each material are unique. These properties are responsible for the strength and durability of the material, as well as the ultimate acceptance and incorporation in the human body. Each material should be individually evaluated and patients should be counseled appropriately before implantation.

Amorphous Analogs of Martian Global Soil: Pair Distribution Function Analyses and Implications for Scattering Models of Chemin X-ray Diffraction Data

NASA Technical Reports Server (NTRS)

Achilles, C. N.; Bish, D. L.; Rampe, E. B.; Morris, R. V.

2015-01-01

Soils on Mars have been analyzed by the Mars Exploration Rovers (MER) and most recently by the Mars Science Laboratory (MSL) rover. Chemical analyses from a majority of soil samples suggest that there is a relatively uniform global soil composition across much of the planet. A soil site, Rocknest, was sampled by the MSL science payload including the CheMin X-ray diffractometer and the Alpha Particle X-ray Spectrometer (APXS). Che- Min X-ray diffraction (XRD) data revealed crystalline phases and a broad, elevated background, indicating the presence of amorphous or poorly ordered materials (Fig 1). Based on the chemical composition of the bulk soil measured by APXS and the composition of crystalline phases derived from unit-cell parameters determined with CheMin data, the percentages of crystalline and amorphous phases were calculated at 51% and 49%, respectively. Attempts to model the amorphous contribution to CheMin XRD patterns were made using amorphous standards and full-pattern fitting methods and show that the broad, elevated background region can be fitted by basaltic glass, allophane, and palagonite. However, the modeling shows only that these phases have scattering patterns similar to that for the soil, not that they represent unique solutions. Here, we use pair distribution function (PDF) analysis to determine the short-range order of amorphous analogs in martian soils and better constrain the amorphous material detected by CheMin.

Teaching Home Economics Content Material in an Individualized Reading Skills Laboratory.

ERIC Educational Resources Information Center

Comerford, Linnie Sue

Eighth grade students whose reading achievement scores fell between second and fourth grade level were given an individualized self-concept approach to reading instruction in home economics. Causes for their reading difficulties were identified as lack of interest in school, no set goals, poor attitudes, poor attendance and suspensions, and…

Magnetically Controlled Shape Memory Behaviour—Materials and Applications

NASA Astrophysics Data System (ADS)

Gandy, A. P.; Sheikh, A.; Neumann, K.; Neumann, K.-U.; Pooley, D.; Ziebeck, K. R. A.

2008-06-01

For most metals a microscopic change in shape occurs above the elastic limit by the irreversible creation and movement of dislocations. However a large number of metallic systems undergo structural, martensitic, phase transformations which are diffusionless, displacive first order transitions from a high-temperature phase to one of lower symmetry below a certain temperature TM. These transitions which have been studied for more than a century are of vital importance because of their key role in producing shape memory phenomena enabling the system to reverse large deformations in the martensitic phase by heating into the austenite phase. In addition to a change in shape (displacement) the effect can also produce a force or a combination of both. Materials having this unique property are increasing being used in medical applications—scoliosis correction, arterial clips, stents, orthodontic wire, orthopaedic implants etc. The structural phase transition essential for shape memory behaviour is usually activated by a change in temperature or applied stress. However for many applications such as for actuators the transformation is not sufficiently rapid. Poor energy conversion also limits the applicability of many shape memory alloys. In medicine a change of temperature or pressure is often inappropriate and new ferromagnetic materials are being considered in which the phenomena can be controlled by an applied magnetic field at constant temperature. In order to achieve this, it is important to optimise three fundamental parameters. These are the saturation magnetisation σs, the Curie temperature Tc and the martensitic temperature TM. Here, σs is important because the magnetic pressure driving the twin boundary motion is 2σsH. Furthermore the material must be in the martensitic state at the operating temperature which should be at or above room temperature. This may be achieved by alloying or controlling the stoichiometry. Recently new intermetallic compounds based on the ferromagnetic prototype Ni2MnGa have been discovered which offer the possibility of controlling the structural phase transition by a magnetic field, hence opening up new possible applications particularly in the field of medicine. The properties of these new materials will be presented and their suitability for applications discussed.

Engineering charge ordering into multiferroicity

NASA Astrophysics Data System (ADS)

He, Xu; Jin, Kui-juan

2016-04-01

Multiferroic materials have attracted great interest but are rare in nature. In many transition-metal oxides, charge ordering and magnetic ordering coexist, so that a method of engineering charge-ordered materials into ferroelectric materials would lead to a large class of multiferroic materials. We propose a strategy for designing new ferroelectric or even multiferroic materials by inserting a spacing layer into each two layers of charge-ordered materials and artificially making a superlattice. One example of the model demonstrated here is the perovskite (LaFeO3)2/LaTiO3 (111) superlattice, in which the LaTiO3 layer acts as the donor and the spacing layer, and the LaFeO3 layer is half doped and performs charge ordering. The collaboration of the charge ordering and the spacing layer breaks the space inversion symmetry, resulting in a large ferroelectric polarization. As the charge ordering also leads to a ferrimagnetic structure, (LaFeO3)2/LaTiO3 is multiferroic. It is expected that this work can encourage the designing and experimental implementation of a large class of multiferroic structures with novel properties.

Photonic Resins: Designing Optical Appearance via Block Copolymer Self-Assembly

PubMed Central

2018-01-01

Despite a huge variety of methodologies having been proposed to produce photonic structures by self-assembly, the lack of an effective fabrication approach has hindered their practical uses. These approaches are typically limited by the poor control in both optical and mechanical properties. Here we report photonic thermosetting polymeric resins obtained through brush block copolymer (BBCP) self-assembly. We demonstrate that the control of the interplay between order and disorder in the obtained photonic structure offers a powerful tool box for designing the optical appearance of the polymer resins in terms of reflected wavelength and scattering properties. The obtained materials exhibit excellent mechanical properties with hardness up to 172 MPa and Young’s modulus over 2.9 GPa, indicating great potential for practical uses as photonic coatings on a variety of surfaces. PMID:29681653

Operando Spectroscopic Microscopy of LiCoO 2 Cathodes Outside Standard Operating Potentials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson Weker, Johanna; Wise, Anna M.; Lim, Kipil

LiCoO 2 can experience over-lithiation (over-discharge) in an electrochemical cell due to poor battery management, failure such as a short circuit, or when LiCoO 2 is utilized as a negative electrode conversion material. Furthermore, in order to understand the chemical and morphological changes which occur during over-lithiation, LiCoO 2 electrodes were studied during deep discharge to 0.8 V with operando X-ray absorption spectroscopy and spectroscopic X-ray microscopy. During over-lithiation, micron-sized LiCoO 2 particles suffer significant cracking, pulverization and an incomplete conversion to Co metal. These irreversible morphological and structural changes then inflict permanent damage on the cathode even during amore » single over-lithiation event and highlight the need for more sophisticated battery management systems.« less

Identification of a limiting mechanism in GaSb-rich superlattice midwave infrared detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Delmas, Marie; Rodriguez, Jean-Baptiste; Rossignol, Rémi

2016-05-07

GaSb-rich superlattice (SL) p-i-n photodiodes grown by molecular beam epitaxy were studied theoretically and experimentally in order to understand the poor dark current characteristics typically obtained. This behavior, independent of the SL-grown material quality, is usually attributed to the presence of defects due to Ga-related bonds, limiting the SL carrier lifetime. By analyzing the photoresponse spectra of reverse-biased photodiodes at 80 K, we have highlighted the presence of an electric field, breaking the minibands into localized Wannier-Stark states. Besides the influence of defects in such GaSb-rich SL structures, this electric field induces a strong tunneling current at low bias which canmore » be the main limiting mechanism explaining the high dark current density of the GaSb-rich SL diode.« less

Operando Spectroscopic Microscopy of LiCoO 2 Cathodes Outside Standard Operating Potentials

DOE PAGES

Nelson Weker, Johanna; Wise, Anna M.; Lim, Kipil; ...

2017-07-14

LiCoO 2 can experience over-lithiation (over-discharge) in an electrochemical cell due to poor battery management, failure such as a short circuit, or when LiCoO 2 is utilized as a negative electrode conversion material. Furthermore, in order to understand the chemical and morphological changes which occur during over-lithiation, LiCoO 2 electrodes were studied during deep discharge to 0.8 V with operando X-ray absorption spectroscopy and spectroscopic X-ray microscopy. During over-lithiation, micron-sized LiCoO 2 particles suffer significant cracking, pulverization and an incomplete conversion to Co metal. These irreversible morphological and structural changes then inflict permanent damage on the cathode even during amore » single over-lithiation event and highlight the need for more sophisticated battery management systems.« less

Helping Elementary Preservice Teachers Learn to Use Curriculum Materials for Effective Science Teaching

ERIC Educational Resources Information Center

Schwarz, Christina V.; Gunckel, Kristin L.; Smith, Ed L.; Covitt, Beth A.; Bae, Minjung; Enfield, Mark; Tsurusaki, Blakely K.

2008-01-01

Curriculum analysis, modification, and enactment are core components of teacher practice. Beginning teachers rely heavily on curriculum materials that are often of poor quality to guide their practice. As a result, we argue that preservice teachers need to learn how to use curriculum materials for effective teaching. To address this concern, the…

Site Formation Processes and Hunter-Gatherers Use of Space in a Tropical Environment: A Geo-Ethnoarchaeological Approach from South India

PubMed Central

Friesem, David E.; Lavi, Noa; Madella, Marco; Ajithprasad, P.; French, Charles

2016-01-01

Hunter-gatherer societies have distinct social perceptions and practices which are expressed in unique use of space and material deposition patterns. However, the identification of archaeological evidence associated with hunter-gatherer activity is often challenging, especially in tropical environments such as rainforests. We present an integrated study combining ethnoarchaeology and geoarchaeology in order to study archaeological site formation processes related to hunter-gatherers’ ways of living in tropical forests. Ethnographic data was collected from an habitation site of contemporary hunter-gatherers in the forests of South India, aimed at studying how everyday activities and way of living dictate patterns of material deposition. Ethnoarchaeological excavations of abandoned open-air sites and a rock-shelter of the same group located deep in the forests, involved field observations and sampling of sediments from the abandoned sites and the contemporary site. Laboratory analyses included geochemical analysis (i.e., FTIR, ICP-AES), phytolith concentration analysis and soil micromorphology. The results present a dynamic spatial deposition pattern of macroscopic, microscopic and chemical materials, which stem from the distinctive ways of living and use of space by hunter-gatherers. This study shows that post-depositional processes in tropical forests result in poor preservation of archaeological materials due to acidic conditions and intensive biological activity within the sediments. Yet, the multiple laboratory-based analyses were able to trace evidence for activity surfaces and their maintenance practices as well as localized concentrations of activity remains such as the use of plants, metals, hearths and construction materials. PMID:27783683

Marital status, social capital, material conditions and self-rated health: a population-based study.

PubMed

Lindström, Martin

2009-12-01

Associations between marital status and self-rated health were investigated, adjusting for material conditions and trust (social capital). The 2004 public-health survey in Skåne is a cross-sectional study. A total of 27,757 persons aged 18-80 years answered a postal questionnaire, which represents 59% of the random sample. A logistic regression model was used to investigate associations between marital status and self-rated health, adjusting for economic problems and trust. The prevalence of poor self-rated health was 28.7% among men and 33.2% among women. Older respondents, respondents born abroad, with medium/low education, low emotional support, low instrumental support, economic problems, low trust, never married and divorced had significantly higher odds ratios of poor self-rated health than their respective reference group. Low trust was significantly higher among the divorced and unmarried compared to the married/cohabitating. Adjustment for economic problems but not for trust reduced the odds ratios of poor self-rated health among the divorced, which became not significant among men. Never married and the divorced have significantly higher age-adjusted odds ratios of poor self-rated health than the married/cohabitating group. Economic problems but not trust seem to affect the association between marital status and poor self-rated health.

Particular Film Formation of Phenytoin at Silica Surfaces

PubMed Central

2014-01-01

Given the increasing number of poorly soluble and thus poorly bioavailable active pharmaceutical materials, there is a demand for innovative formulation platforms for such molecules. Thus a focus on enhancing dissolution properties of poorly soluble drugs exists. Within this study, the spin coating of acetone solutions containing 5,5-diphenyl-2,4-imidazolidinedione (phenytoin) in various concentrations is evaluated. The results reveal strong variations of the morphology of deposited phenytoin crystals at silica surfaces. Individual separated particles are obtained on low phenytoin concentrations, and closely packed particular films form when the concentration is increased. As the material is isomorphic, these various morphologies have the same crystalline structure. Dissolution experiments reveal that both the apparent maximum solubility and as the dissolution rate are strongly enhanced compared to bulk powder, suggesting that formulation based on this preparative technique will allow overcoming the low solubility problematic for a variety of drugs. PMID:24417472

Thermal analysis of laser additive manufacturing of aluminium alloys: Experiment and simulation

NASA Astrophysics Data System (ADS)

Bock, Frederic E.; Froend, Martin; Herrnring, Jan; Enz, Josephin; Kashaev, Nikolai; Klusemann, Benjamin

2018-05-01

Laser additive manufacturing (LAM) has become increasingly popular in industry in recent decades because it enables exceptional degrees of freedom regarding the structural design of lightweight components compared to subtractive manufacturing techniques. Laser metal deposition (LMD) of wire-fed material shows in particular the advantages such as high process velocity and efficient use of material compared to other LAM processes. During wire-based LMD, the material is deposited onto a substrate and supplemented by successive layers allowing a layer-wise production of complex three-dimensional structures. Despite the increased productivity of LMD, regarding the ability to process aluminium alloys, there is still a lack in quality and reproducibility due to the inhomogeneous temperature distribution during the process, leading to undesired residual stresses, distortions and inconsistent layer geometries and poor microstructures. In this study, the aluminium alloy AA5087 as wire and AA5754 as substrate material were utilized for LMD. In order to obtain information about the temperature field during LMD, thermocouple and thermography measurements were performed during the process. The temperature measurements were used to validate a finite element model regarding the heat distribution, which will be further used to investigate the temperature field evolution over time. To consider the continuous addition of material within the FE-model, an inactive/active element approach was chosen, where initially deactivated elements are activated corresponding to the deposition of material. The first results of the simulation and the experiments show good agreement. Therefore, the model can be used in the future for LMD process optimization, e.g., in terms of minimizing local variations of the thermal load for each layer.

Investigation of wetting property between liquid lead lithium alloy and several structural materials for Chinese DEMO reactor

NASA Astrophysics Data System (ADS)

Lu, Wei; Wang, Weihua; Jiang, Haiyan; Zuo, Guizhong; Pan, Baoguo; Xu, Wei; Chu, Delin; Hu, Jiansheng; Qi, Junli

2017-10-01

The dual-cooled lead lithium (PbLi) blanket is considered as one of the main options for the Chinese demonstration reactor (DEMO). Liquid PbLi alloy is used as the breeder material and coolant. Reduced activation ferritic/martensitic (RAFM) steel, stainless steel and the silicon carbide ceramic matrix composite (SiCf) are selected as the substrate materials for different use. To investigate the wetting property and inter-facial interactions of PbLi/RAFM steel, PbLi/SS316L, PbLi/SiC and PbLi/SiCf couples, in this paper, the special vacuum experimental device is built, and the 'dispensed droplet' modification for the classic sessile droplet technique is made. Contact angles are measured between the liquid PbLi and the various candidate materials at blanket working temperature from 260 to 480 °C. X-ray photoelectron spectroscopy (XPS) is used to characterize the surface components of PbLi droplets and substrate materials, in order to study the element trans-port and corrosion mechanism. Results show that SiC composite (SiCf) and SiC ceramic show poor wetting properties with the liquid PbLi alloy. Surface roughness and testing temperature only provide tiny improvements on the wetting property below 480 °C. RAFM steel performs better wetting properties and corrosion residence when contacted with molten PbLi, while SS316L shows low corrosion residence above 420 °C for the decomposition of protective surface film mainly consisted of chromic sesquioxide. The results could provide meaningful compatibility database of liquid PbLi alloy and valuable reference in engineering design of candidate structural and functional materials for future fusion blanket.

From properties to materials: An efficient and simple approach.

PubMed

Huwig, Kai; Fan, Chencheng; Springborg, Michael

2017-12-21

We present an inverse-design method, the poor man's materials optimization, that is designed to identify materials within a very large class with optimized values for a pre-chosen property. The method combines an efficient genetic-algorithm-based optimization, an automatic approach for generating modified molecules, a simple approach for calculating the property of interest, and a mathematical formulation of the quantity whose value shall be optimized. In order to illustrate the performance of our approach, we study the properties of organic molecules related to those used in dye-sensitized solar cells, whereby we, for the sake of proof of principle, consider benzene as a simple test system. Using a genetic algorithm, the substituents attached to the organic backbone are varied and the best performing molecules are identified. We consider several properties to describe the performance of organic molecules, including the HOMO-LUMO gap, the sunlight absorption, the spatial distance of the orbitals, and the reorganisation energy. The results show that our method is able to identify a large number of good candidate structures within a short time. In some cases, chemical/physical intuition can be used to rationalize the substitution pattern of the best structures, although this is not always possible. The present investigations provide a solid foundation for dealing with more complex and technically relevant systems such as porphyrins. Furthermore, our "properties first, materials second" approach is not limited to solar-energy harvesting but can be applied to many other fields, as briefly is discussed in the paper.

From properties to materials: An efficient and simple approach

NASA Astrophysics Data System (ADS)

Huwig, Kai; Fan, Chencheng; Springborg, Michael

2017-12-01

We present an inverse-design method, the poor man's materials optimization, that is designed to identify materials within a very large class with optimized values for a pre-chosen property. The method combines an efficient genetic-algorithm-based optimization, an automatic approach for generating modified molecules, a simple approach for calculating the property of interest, and a mathematical formulation of the quantity whose value shall be optimized. In order to illustrate the performance of our approach, we study the properties of organic molecules related to those used in dye-sensitized solar cells, whereby we, for the sake of proof of principle, consider benzene as a simple test system. Using a genetic algorithm, the substituents attached to the organic backbone are varied and the best performing molecules are identified. We consider several properties to describe the performance of organic molecules, including the HOMO-LUMO gap, the sunlight absorption, the spatial distance of the orbitals, and the reorganisation energy. The results show that our method is able to identify a large number of good candidate structures within a short time. In some cases, chemical/physical intuition can be used to rationalize the substitution pattern of the best structures, although this is not always possible. The present investigations provide a solid foundation for dealing with more complex and technically relevant systems such as porphyrins. Furthermore, our "properties first, materials second" approach is not limited to solar-energy harvesting but can be applied to many other fields, as briefly is discussed in the paper.

Synthesis and electrochemical characterization of mesoporous Li2FeSiO4/C composite cathode material for Li-ion batteries

NASA Astrophysics Data System (ADS)

Kumar, Ajay; Jayakumar, O. D.; Bazzi, Khadije; Nazri, Gholam-Abbas; Naik, Vaman M.; Naik, Ratna

2015-03-01

Lithium iron silicate (Li2FeSiO4) has the potential as cathode for Li ion batteries due to its high theoretical capacity (~ 330 mAh/g) and improved safety. The application of Li2FeSiO4 as cathode material has been challenged by its poor electronic conductivity and slow lithium ion diffusion in the solid phase. In order to solve these problems, we have synthesized mesoporous Li2FeSiO4/C composites by sol-gel method using the tri-block copolymer (P123) as carbon source. The phase purity and morphology of the composite materials were characterized by x-ray diffraction, SEM and TEM. The XRD pattern confirmed the formation of ~ 12 nm size Li2FeSiO4 crystallites in composites annealed at 600 °C for 6 h under argon atmosphere. The electrochemical properties are measured using the composite material as positive electrode in a standard coin cell configuration with lithium as the active anode and the cells were tested using AC impedance spectroscopy, cyclic voltammetry, and galvanostatic charge/discharge cycling. The Li2FeSiO4/C composites showed a discharge capacity of ~ 240 mAh/g at a rate of C/30 at room temperature. The effect of different annealing temperature and synthesis time on the electrochemical performance of Li2FeSiO4/C will be presented.

'Why didn't you write a not-for-cardiopulmonary resuscitation order?' Unexpected death or failure of process?

PubMed

Levinson, Michele; Mills, Amber; Barrett, Jonathan; Sritharan, Gaya; Gellie, Anthea

2018-02-01

Objective The aim of the present study was to understand the reasons for the delivery of non-beneficial cardiopulmonary resuscitation (CPR) attempts in a tertiary private hospital over 12 months. We determined doctors' expectations of survival after CPR for their patient, whether they had considered a not-for-resuscitation (NFR) order and the barriers to completion of NFR orders. Methods Anonymous questionnaires were sent to the doctors primarily responsible for a given patient's care in the hospital within 2 weeks of the unsuccessful CPR attempt. The data were analysed quantitatively where appropriate and qualitatively for themes for open-text responses Results Most doctors surveyed in the present study understood the poor outcome after CPR in the older person. Most doctors had an expectation that their own patient had a poor prognosis and a poor likely predicted outcome after CPR. This implied that the patient's death was neither unexpected nor likely to be reversible. Some doctors considered NFR orders, but multiple barriers to completion were cited, including the family's wishes, being time poor and diffusion or deferral of responsibility. Conclusions It is likely that futile CPR is provided contrary to policy and legal documents relating to end-of-life care, with the potential for harms relating to both patient and family, and members of resuscitation teams. The failure appears to relate to process rather than recognition of poor patient outcome. What is known about the topic? Mandatory CPR has been established in Australian hospitals on the premise that it will save lives. The outcome from in-hospital cardiac arrest has not improved despite significant training and resources. The outcome for those acutely hospitalised patients aged over 80 years has been repeatedly demonstrated to be poor with significant morbidity in the survivors. There is emerging literature on the extent of the delivery of non-beneficial treatments at the end of life, including futile CPR, the recognition of harms incurred by patients, families and members of the resuscitation teams and on the opportunity cost of the inappropriate use of resources. What does this paper add? This is the first study, to our knowledge, that has demonstrated that doctors understood the outcomes for CPR, particularly in those aged 80 years and older, and that failure to recognise poor outcome and prognosis in their own patients is not a barrier to writing NFR orders. What are the implications for practitioners? Recognition of the poor outcomes from CPR for the elderly patient for whom the doctor has a duty of care should result in a discussion with the patients, allowing an exploration of values and expectations of treatment. This would promote shared decision making, which includes the use of CPR. Facilitation of these discussions should be the focus of health service review.

Interrelations among pyroclastic surge, pyroclastic flow, and lahars in Smith Creek valley during first minutes of 18 May 1980 eruption of Mount St. Helens, USA

USGS Publications Warehouse

Brantley, S.R.; Waitt, R.B.

1988-01-01

A devastating pyroclastic surge and resultant lahars at Mount St. Helens on 18 May 1980 produced several catastrophic flowages into tributaries on the northeast volcano flank. The tributaries channeled the flows to Smith Creek valley, which lies within the area devastated by the surge but was unaffected by the great debris avalanche on the north flank. Stratigraphy shows that the pyroclastic surge preceded the lahars; there is no notable "wet" character to the surge deposits. Therefore the lahars must have originated as snowmelt, not as ejected water-saturated debris that segregated from the pyroclastic surge as has been inferred for other flanks of the volcano. In stratigraphic order the Smith Creek valley-floor materials comprise (1) a complex valley-bottom facies of the pyroclastic surge and a related pyroclastic flow, (2) an unusual hummocky diamict caused by complex mixing of lahars with the dry pyroclastic debris, and (3) deposits of secondary pyroclastic flows. These units are capped by silt containing accretionary lapilli, which began falling from a rapidly expanding mushroom-shaped cloud 20 minutes after the eruption's onset. The Smith Creek valley-bottom pyroclastic facies consists of (a) a weakly graded basal bed of fines-poor granular sand, the deposit of a low-concentration lithic pyroclastic surge, and (b) a bed of very poorly sorted pebble to cobble gravel inversely graded near its base, the deposit of a high-concentration lithic pyroclastic flow. The surge apparently segregated while crossing the steep headwater tributaries of Smith Creek; large fragments that settled from the turbulent surge formed a dense pyroclastic flow along the valley floor that lagged behind the front of the overland surge. The unusual hummocky diamict as thick as 15 m contains large lithic clasts supported by a tough, brown muddy sand matrix like that of lahar deposits upvalley. This unit contains irregular friable lenses and pods meters in diameter, blocks incorporated from the underlying dry and hot pyroclastic material that had been deposited only moments earlier. The hummocky unit is the deposit of a high-viscosity debris flow which formed when lahars mingled with the pyroclastic materials on Smith Creek valley floor. Overlying the debris flow are voluminous pyroclastic deposits of pebbly sand cut by fines-poor gas-escape pipes and containing charred wood. The deposits are thickest in topographic lows along margins of the hummocky diamict. Emplaced several minutes after the hot surge had passed, this is the deposit of numerous secondary pyroclastic flows derived from surge material deposited unstably on steep valley sides. ?? 1988 Springer-Verlag.

Formulation of a danazol cocrystal with controlled supersaturation plays an essential role in improving bioavailability.

PubMed

Childs, Scott L; Kandi, Praveen; Lingireddy, Sreenivas Reddy

2013-08-05

Cocrystals have become an established and adopted approach for creating crystalline solids with improved physical properties, but incorporating cocrystals into enabling pre-clinical formulations suitable for animal dosing has received limited attention. The dominant approach to in vivo evaluation of cocrystals has focused on deliberately excluding additional formulation in favor of "neat" aqueous suspensions of cocrystals or loading neat cocrystal material into capsules. However, this study demonstrates that, in order to take advantage of the improved solubility of a 1:1 danazol:vanillin cocrystal, a suitable formulation was required. The neat aqueous suspension of the danazol:vanillin cocrystal had a modest in vivo improvement of 1.7 times higher area under the curve compared to the poorly soluble crystal form of danazol dosed under identical conditions, but the formulated aqueous suspension containing 1% vitamin E-TPGS (TPGS) and 2% Klucel LF Pharm hydroxypropylcellulose improved the bioavailability of the cocrystal by over 10 times compared to the poorly soluble danazol polymorph. In vitro powder dissolution data obtained under non-sink biorelevant conditions correlate with in vivo data in rats following 20 mg/kg doses of danazol. In the case of the danazol:vanillin cocrystal, using a combination of cocrystal, solubilizer, and precipitation inhibitor in a designed supersaturating drug delivery system resulted in a dramatic improvement in the bioavailability. When suspensions of neat cocrystal material fail to return the anticipated bioavailability increase, a supersaturating formulation may be able to create the conditions required for the increased cocrystal solubility to be translated into improved in vivo absorption at levels competitive with existing formulation approaches used to overcome solubility limited bioavailability.

Kinetic Monte Carlo Study of Li Intercalation in LiFePO4.

PubMed

Xiao, Penghao; Henkelman, Graeme

2018-01-23

Even as a commercial cathode material, LiFePO 4 remains of tremendous research interest for understanding Li intercalation dynamics. The partially lithiated material spontaneously separates into Li-poor and Li-rich phases at equilibrium. Phase segregation is a surprising property of LiFePO 4 given its high measured rate capability. Previous theoretical studies, aiming to describe Li intercalation in LiFePO 4 , include both atomic-scale density functional theory (DFT) calculations of static Li distributions and entire-particle-scale phase field models, based upon empirical parameters, studying the dynamics of the phase separation. Little effort has been made to bridge the gap between these two scales. In this work, DFT calculations are used to fit a cluster expansion for the basis of kinetic Monte Carlo calculations, which enables long time scale simulations with accurate atomic interactions. This atomistic model shows how the phases evolve in Li x FePO 4 without parameters from experiments. Our simulations reveal that an ordered Li 0.5 FePO4 phase with alternating Li-rich and Li-poor planes along the ac direction forms between the LiFePO 4 and FePO 4 phases, which is consistent with recent X-ray diffraction experiments showing peaks associated with an intermediate-Li phase. The calculations also help to explain a recent puzzling experiment showing that LiFePO 4 particles with high aspect ratios that are narrower along the [100] direction, perpendicular to the [010] Li diffusion channels, actually have better rate capabilities. Our calculations show that lateral surfaces parallel to the Li diffusion channels, as well as other preexisting sites that bind Li weakly, are important for phase nucleation and rapid cycling performance.

Dissolution kinetics of iron-, manganese-, and copper-containing synthetic hydroxyapatites

NASA Technical Reports Server (NTRS)

Sutter, B.; Hossner, L. R.; Ming, D. W.

2005-01-01

Micronutrient-substituted synthetic hydroxyapatite (SHA) is being evaluated by the National Aeronautics and Space Administration's (NASA) Advanced Life Support (ALS) Program for crop production on long-duration human missions to the International Space Station or for future Lunar or Martian outposts. The stirred-flow technique was utilized to characterize Ca, P, Fe, Mn, and Cu release characteristics from Fe-, Mn-, and Cu-containing SHA in deionized (DI) water, citric acid, and diethylene-triamine-pentaacetic acid (DTPA). Initially, Ca and P release rates decreased rapidly with time and were controlled by a non-SHA calcium phosphate phase(s) with low Ca/P solution molar ratios (0.91-1.51) relative to solid SHA ratios (1.56-1.64). At later times, Ca/P solution molar ratios (1.47-1.79) were near solid SHA ratios and release rates decreased slowly indicating that SHA controlled Ca and P release. Substituted SHA materials had faster dissolution rates relative to unsubstituted SHA. The initial metal release rate order was Mn >> Cu > Fe which followed metal-oxide/phosphate solubility suggesting that poorly crystalline metal-oxides/phosphates were dominating metal release. Similar metal release rates for all substituted SHA (approximately 0.01 cmol kg-1 min-1) at the end of the DTPA experiment indicated that SHA dissolution was supplying the metals into solution and that poorly crystalline metal-oxide/phosphates were not controlling metal release. Results indicate that non-SHA Ca-phosphate phases and poorly crystalline metal-oxide/phosphates will contribute Ca, P, and metals. After these phases have dissolved, substituted SHA will be the source of Ca, P, and metals for plants.

Materials and fabrication of electrode scaffolds for deposition of MnO2 and their true performance in supercapacitors

NASA Astrophysics Data System (ADS)

Cao, Jianyun; Li, Xiaohong; Wang, Yaming; Walsh, Frank C.; Ouyang, Jia-Hu; Jia, Dechang; Zhou, Yu

2015-10-01

MnO2 is a promising electrode material for high energy supercapacitors because of its large pseudo-capacitance. However, MnO2 suffers from low electronic conductivity and poor cation diffusivity, which results in poor utilization and limited rate performance of traditional MnO2 powder electrodes, obtained by pressing a mixed paste of MnO2 powder, conductive additive and polymer binder onto metallic current collectors. Developing binder-free MnO2 electrodes by loading nanoscale MnO2 deposits on pre-fabricated device-ready electrode scaffolds is an effective way to achieve both high power and energy performance. These electrode scaffolds, with interconnected skeletons and pore structures, will not only provide mechanical support and electron collection as traditional current collectors but also fast ion transfer tunnels, leading to high MnO2 utilization and rate performance. This review covers design strategies, materials and fabrication methods for the electrode scaffolds. Rational evaluation of the true performance of these electrodes is carried out, which clarifies that some of the electrodes with as-claimed exceptional performances lack potential in practical applications due to poor mass loading of MnO2 and large dead volume of inert scaffold materials/void spaces in the electrode structure. Possible ways to meet this challenge and bring MnO2 electrodes from laboratory studies to real-world applications are considered.

Heat transfer enhancement in a lithium-ion cell through improved material-level thermal transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vishwakarma, Vivek; Waghela, Chirag; Wei, Zi

2016-09-25

We report that while Li-ion cells offer excellent electrochemical performance for several applications including electric vehicles, they also exhibit poor thermal transport characteristics, resulting in reduced performance, overheating and thermal runaway. Inadequate heat removal from Li-ion cells originates from poor thermal conductivity within the cell. This paper identifies the rate-limiting material-level process that dominates overall thermal conduction in a Li-ion cell. Results indicate that thermal characteristics of a Li-ion cell are largely dominated by heat transfer across the cathode-separator interface rather than heat transfer through the materials themselves. This interfacial thermal resistance contributes around 88% of total thermal resistance inmore » the cell. Measured value of interfacial resistance is close to that obtained from theoretical models that account for weak adhesion and large acoustic mismatch between cathode and separator. Further, to address this problem, an amine-based chemical bridging of the interface is carried out. This is shown to result in in four-times lower interfacial thermal resistance without deterioration in electrochemical performance, thereby increasing effective thermal conductivity by three-fold. This improvement is expected to reduce peak temperature rise during operation by 60%. Finally, by identifying and addressing the material-level root cause of poor thermal transport in Li-ion cells, this work may contribute towards improved thermal performance of Li-ion cells.« less

Evolution of a sediment wave in an experimental channel

Treesearch

Thomas E. Lisle; James E. Pizzuto; Hiroshi Ikeda; Fujiko Iseya; Yoshinori Kodama

1997-01-01

Abstract - The routing of bed material through channels is poorly understood. We approach the problem by observing and modeling the fate of a low-amplitude sediment wave of poorly sorted sand that we introduced into an experimental channel transporting sediment identical to that of the introduced wave. The wave essentially dispersed upstream and downstream without...

7 CFR 52.3188 - Work sheet for dried prunes.

Code of Federal Regulations, 2014 CFR

2014-01-01

... maximum Total of all defects, including off-color 10 percent 15 percent No limit except as indicated below. Total of all defects, including off-color and poor texture 20 percent Poor texture, end cracks, skin or... material, insect infestation, decay But no more than 6 percent But no more than 8 percent End cracks,2 skin...

7 CFR 52.3184 - Grades of dried prunes.

Code of Federal Regulations, 2012 CFR

2012-01-01

... affected by: Not more than 5 percent, by weight, may be affected by: Off-color. End cracks. 1 Skin or flesh... weight, may be affected by: Not more than 1 percent, by weight, may be affected by: Off-color. Poor texture. Mold. Decay. Poor texture. End cracks. Dirt. End cracks. Skin or flesh Foreign material. Skin or...

7 CFR 52.3188 - Work sheet for dried prunes.

Code of Federal Regulations, 2013 CFR

2013-01-01

... maximum Total of all defects, including off-color 10 percent 15 percent No limit except as indicated below. Total of all defects, including off-color and poor texture 20 percent Poor texture, end cracks, skin or... material, insect infestation, decay But no more than 6 percent But no more than 8 percent End cracks,2 skin...

Transparent conducting oxide nanotubes

NASA Astrophysics Data System (ADS)

Alivov, Yahya; Singh, Vivek; Ding, Yuchen; Nagpal, Prashant

2014-09-01

Thin film or porous membranes made of hollow, transparent, conducting oxide (TCO) nanotubes, with high chemical stability, functionalized surfaces and large surface areas, can provide an excellent platform for a wide variety of nanostructured photovoltaic, photodetector, photoelectrochemical and photocatalytic devices. While large-bandgap oxide semiconductors offer transparency for incident light (below their nominal bandgap), their low carrier concentration and poor conductivity makes them unsuitable for charge conduction. Moreover, materials with high conductivity have nominally low bandgaps and hence poor light transmittance. Here, we demonstrate thin films and membranes made from TiO2 nanotubes heavily-doped with shallow Niobium (Nb) donors (up to 10%, without phase segregation), using a modified electrochemical anodization process, to fabricate transparent conducting hollow nanotubes. Temperature dependent current-voltage characteristics revealed that TiO2 TCO nanotubes, doped with 10% Nb, show metal-like behavior with resistivity decreasing from 6.5 × 10-4 Ωcm at T = 300 K (compared to 6.5 × 10-1 Ωcm for nominally undoped nanotubes) to 2.2 × 10-4 Ωcm at T = 20 K. Optical properties, studied by reflectance measurements, showed light transmittance up to 90%, within wavelength range 400 nm-1000 nm. Nb doping also improves the field emission properties of TCO nanotubes demonstrating an order of magnitude increase in field-emitter current, compared to undoped samples.

Reason behind wet pack after steam sterilization and its consequences: An overview from Central Sterile Supply Department of a cancer center in eastern India.

PubMed

Basu, Debabrata

Wet pack after steam sterilization process that means there are surely obtain millions of microorganisms that can breed and multiply rapidly and objects are unsterile and can never be used for further procedure. There are many reasons behind the wet pack occurrences after autoclaving like poor quality of wrapping materials, faulty valves of rigid container, faulty loading and packaging technique, poor steam quality, sterilizer malfunction and may be design related problems in CSSD sterile storage area. Cause of wet pack after steam sterilization processes may occur severe problems because of wasted time and effort, increased work load, increased cost, potentially contaminated instruments, infection risk to the patient, poor patient outcomes and delayed or cancellation of procedures. But such wet pack scenario can be avoided by various methods by using good steam (water) quality, performing periodic maintenance of the Autoclaves, avoidance of sterilizer overloading, allowing adequate post sterilization time to cool down the materials to room temperature, using good quality wrapping materials, properly maintain temperature and humidity of sterile storage area etc. Copyright © 2016 King Saud Bin Abdulaziz University for Health Sciences. Published by Elsevier Ltd. All rights reserved.

77 FR 43780 - Federal Acquisition Regulation; Changes to Time-and-Materials and Labor-Hour Contracts and Orders

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-26

... Federal Acquisition Regulation; Changes to Time-and-Materials and Labor-Hour Contracts and Orders AGENCIES... changing the scope of work for a time-and-materials (T&M) or labor-hour (LH) contract or order. DATES...-043, ``Time-and-Materials and Labor-Hour Contracts for Commercial Items'', was published as a final...

Transcriptome comparisons shed light on the pre-condition and potential barrier for C4 photosynthesis evolution in eudicots.

PubMed

Tao, Yimin; Lyu, Ming-Ju Amy; Zhu, Xin-Guang

2016-05-01

C4 photosynthesis evolved independently from C3 photosynthesis in more than 60 lineages. Most of the C4 lineages are clustered together in the order Poales and the order Caryophyllales while many other angiosperm orders do not have C4 species, suggesting the existence of biological pre-conditions in the ancestral C3 species that facilitate the evolution of C4 photosynthesis in these lineages. To explore pre-adaptations for C4 photosynthesis evolution, we classified C4 lineages into the C4-poor and the C4-rich groups based on the percentage of C4 species in different genera and conducted a comprehensive comparison on the transcriptomic changes between the non-C4 species from the C4-poor and the C4-rich groups. Results show that species in the C4-rich group showed higher expression of genes related to oxidoreductase activity, light reaction components, terpene synthesis, secondary cell synthesis, C4 cycle related genes and genes related to nucleotide metabolism and senescence. In contrast, C4-poor group showed up-regulation of a PEP/Pi translocator, genes related to signaling pathway, stress response, defense response and plant hormone metabolism (ethylene and brassinosteroid). The implications of these transcriptomic differences between the C4-rich and C4-poor groups to C4 evolution are discussed.

Design of Boiler Welding for Improvement of Lifetime and Cost Control.

PubMed

Thong-On, Atcharawadi; Boonruang, Chatdanai

2016-11-03

Fe-2.25Cr-1Mo a widely used material for headers and steam tubes of boilers. Welding of steam tube to header is required for production of boiler. Heat affected zone of the weld can have poor mechanical properties and poor corrosion behavior leading to weld failure. The cost of material used for steam tube and header of boiler should be controlled. This study propose a new materials design for boiler welding to improve the lifetime and cost control, using tungsten inert gas (TIG) welding of Fe-2.25Cr-1Mo tube to carbon steel pipe with chromium-containing filler. The cost of production could be reduced by the use of low cost material such as carbon steel pipe for boiler header. The effect of chromium content on corrosion behavior of the weld was greater than that of the microstructure. The lifetime of the welded boiler can be increased by improvement of mechanical properties and corrosion behavior of the heat affected zone.

Design of Boiler Welding for Improvement of Lifetime and Cost Control

PubMed Central

Thong-On, Atcharawadi; Boonruang, Chatdanai

2016-01-01

Fe-2.25Cr-1Mo a widely used material for headers and steam tubes of boilers. Welding of steam tube to header is required for production of boiler. Heat affected zone of the weld can have poor mechanical properties and poor corrosion behavior leading to weld failure. The cost of material used for steam tube and header of boiler should be controlled. This study propose a new materials design for boiler welding to improve the lifetime and cost control, using tungsten inert gas (TIG) welding of Fe-2.25Cr-1Mo tube to carbon steel pipe with chromium-containing filler. The cost of production could be reduced by the use of low cost material such as carbon steel pipe for boiler header. The effect of chromium content on corrosion behavior of the weld was greater than that of the microstructure. The lifetime of the welded boiler can be increased by improvement of mechanical properties and corrosion behavior of the heat affected zone. PMID:28774014

Solubility product constants of covellite and a poorly crystalline copper sulfide precipitate at 298 K

NASA Astrophysics Data System (ADS)

Shea, Damian; Helz, George R.

1989-02-01

The equilibrium constant at 25°C for the following reaction has been measured in NaCl media by an indirect method: CuS(cov) + H +(aq) ⇄ Cu 2+(aq) + HS -(qa), Ksp = MCu 2+MHS -(10 +pH) where CuS(cov) designates synthetic covellite. Values of pKsp are 21.39, 21.04 and 20.95 at NaCl = 0.2, 0.7 and 1.0 M, respectively; the uncertainty in these Ksp values is ±0.15. The free energy of formation of covellite, for which published values are discordant, is calculated to be -11.83±0.4 kcal/mole at 298 K (-49.50 ± 1.7 kJ/mole). This value is obtained by extrapolating the meaured pKsp values to infinite dilution with corrections for Cl - complexing. Applying similar Cl - complexing corrections, based on recent measurements by Seward, to previously published solubility data for galena yields a revised pKsp0 for galena of 12.78. A poorly crystalline precipitate, obtained by mixing Cu 2+ and HS - solutions, yielded a reversible solubility product 3 orders of magnitude greater than that of covellite but about 3 orders of magnitude less than that of a truly amorphous phase, super-cooled liquid CuS. The poorly crystalline phase has not been studied previously. Its bulk composition was Cu 1.18S, but microprobe analysis revealed that it was a partially exsolved mixture of roughly Cu 1.11S and Cu 1.32S (similar to known blaubleibender covellites). It was kinetically unstable, and converted to covellite when thermally annealed or when exposed to polysulfide solutions. Because of its instability, a material of this nature is unlikely to account for the amorphous copper sulfide alleged to occur in the Red Sea Brine deposits. However, it is possible that on short time scales dissolved Cu in sulfidic waters is controlled by metastable, rather than stable phases, as is known to be the case with dissolved Fe.

Inverse correlation between quasiparticle mass and T c in a cuprate high-T c superconductor.

PubMed

Putzke, Carsten; Malone, Liam; Badoux, Sven; Vignolle, Baptiste; Vignolles, David; Tabis, Wojciech; Walmsley, Philip; Bird, Matthew; Hussey, Nigel E; Proust, Cyril; Carrington, Antony

2016-03-01

Close to a zero-temperature transition between ordered and disordered electronic phases, quantum fluctuations can lead to a strong enhancement of electron mass and to the emergence of competing phases such as superconductivity. A correlation between the existence of such a quantum phase transition and superconductivity is quite well established in some heavy fermion and iron-based superconductors, and there have been suggestions that high-temperature superconductivity in copper-oxide materials (cuprates) may also be driven by the same mechanism. Close to optimal doping, where the superconducting transition temperature T c is maximal in cuprates, two different phases are known to compete with superconductivity: a poorly understood pseudogap phase and a charge-ordered phase. Recent experiments have shown a strong increase in quasiparticle mass m* in the cuprate YBa2Cu3O7-δ as optimal doping is approached, suggesting that quantum fluctuations of the charge-ordered phase may be responsible for the high-T c superconductivity. We have tested the robustness of this correlation between m* and T c by performing quantum oscillation studies on the stoichiometric compound YBa2Cu4O8 under hydrostatic pressure. In contrast to the results for YBa2Cu3O7-δ, we find that in YBa2Cu4O8, the mass decreases as T c increases under pressure. This inverse correlation between m* and T c suggests that quantum fluctuations of the charge order enhance m* but do not enhance T c.

Inverse correlation between quasiparticle mass and Tc in a cuprate high-Tc superconductor

PubMed Central

Putzke, Carsten; Malone, Liam; Badoux, Sven; Vignolle, Baptiste; Vignolles, David; Tabis, Wojciech; Walmsley, Philip; Bird, Matthew; Hussey, Nigel E.; Proust, Cyril; Carrington, Antony

2016-01-01

Close to a zero-temperature transition between ordered and disordered electronic phases, quantum fluctuations can lead to a strong enhancement of electron mass and to the emergence of competing phases such as superconductivity. A correlation between the existence of such a quantum phase transition and superconductivity is quite well established in some heavy fermion and iron-based superconductors, and there have been suggestions that high-temperature superconductivity in copper-oxide materials (cuprates) may also be driven by the same mechanism. Close to optimal doping, where the superconducting transition temperature Tc is maximal in cuprates, two different phases are known to compete with superconductivity: a poorly understood pseudogap phase and a charge-ordered phase. Recent experiments have shown a strong increase in quasiparticle mass m* in the cuprate YBa2Cu3O7-δ as optimal doping is approached, suggesting that quantum fluctuations of the charge-ordered phase may be responsible for the high-Tc superconductivity. We have tested the robustness of this correlation between m* and Tc by performing quantum oscillation studies on the stoichiometric compound YBa2Cu4O8 under hydrostatic pressure. In contrast to the results for YBa2Cu3O7-δ, we find that in YBa2Cu4O8, the mass decreases as Tc increases under pressure. This inverse correlation between m* and Tc suggests that quantum fluctuations of the charge order enhance m* but do not enhance Tc. PMID:27034989

Interfacial Engineering of Inorganic Materials for Energy Storage and Conversion Applications

NASA Astrophysics Data System (ADS)

Samiee, Mojtaba

Since the micrometer-sized bulk materials have reached their inherent limits, development of new materials with high performance is essential for low cost and environmentally friendly electrochemical energy storage and conversion devices. One approach is to take advantage of interfacial engineering in order to modify currently developed materials, thus improving their properties for specific applications. The advantage of interfacial engineering is that it can also be applied to newly developed materials to further improve their properties for the specific applications. In first part of this dissertation, a systematic study is performed to investigate the effect of annealing in reducing atmospheres with different oxygen partial pressures and presence of other species (Ar, H2, N2, vacuum or hydrocarbon) on visible-light photocatalytic activity of TiO2. In second part, a facile nitridation method is used to improve the rate capability of TiO 2 as anode material for Li ion batteries. The enhanced high-rate capacities are attributed to moderate surface nitridation with less-disordered nitridated regions, which may enhance the surface electronic conductivity without forming discrete, nanoscale, and surface amorphous films to block the lithium transport. In third part, pseudocapacitive properties of V2O5-based adsorbates supported on TiO2 nanoparticles is systematically measured. Surface amorphous films (SAFs), which form naturally at thermodynamic equilibria at 550-600 °C with self-regulating or "equilibrium" thicknesses on the order of 1 nm, exhibit superior electrochemical performance at moderate and high scan rates (20-500 mV/s) that are of prime importance for supercapacitor applications, as compared with submonolayer and monolayer adsorbates formed at lower equilibration temperatures. In fourth part, we perform a combined experimental and computational investigation into the effects of aliovalent doping in NASICON on both bulk and grain boundary ionic conductivity. Our results show that the dopants with low solid solubility limits in NASICON solid solution lead to the formation of a conducting secondary phase at grain boundaries, thereby improving effective grain boundary conductivity that is otherwise hindered by the poorly-conducting Na3PO4 and ZrO2 secondary phases in undoped NASICON. In fifth part, inline electron holography technique is used to directly observe and investigate the space charge layers at grain boundaries of Y-doped BaZrO3.

Interrater reliability to assure valid content in peer review of CME-accredited presentations.

PubMed

Quigg, Mark; Lado, Fred A

2009-01-01

The Accreditation Council for Continuing Medical Education (ACCME) provides guidelines for continuing medical education (CME) materials to mitigate problems in the independence or validity of content in certified activities; however, the process of peer review of materials appears largely unstudied and the reproducibility of peer-review audits for ACCME accreditation and designation of American Medical Association Category 1 Credit(TM) is unknown. Categories of presentation defects were constructed from discussions of the CME committee of the American Epilepsy Society: (1) insufficient citation, (2) poor formatting, (3) nonacknowledgment of non-FDA-approved use, (4) misapplied data, (5) 1-sided data, (6) self- or institutional promotion, (7) conflict of interest/commercial bias, (8) other, or (9) no defect. A PowerPoint lecture (n = 29 slides) suitable for presentation to general neurologists was purposefully created with the above defects. A multirater, multilevel kappa statistic was determined from the number and category of defects. Of 14 reviewers, 12 returned completed surveys (86%) identifying a mean +/- standard deviation 1.6 +/- 1.1 defects/slide. The interrater kappa equaled 0.115 (poor reliability) for number of defects/slides. No individual categories achieved kappa > 0.38. Interrater reliability on the rating of durable materials used in subspecialty CME was poor. Guidelines for CME appropriate content are too subjective to be applied reliably by raters knowledgeable in their specialty field but relatively untrained in the specifics of CME requirements. The process of peer review of CME materials would be aided by education of physicians on validation of materials appropriate for CME.

Synthesizing Nanomaterials for Energy Applications: Probing Activity as a Function of Composition, Morphology and Purity to Address Key Issues Associated with Fuel Cells and Li-Ion Batteries

NASA Astrophysics Data System (ADS)

Scofield, Megan Elaine

With the growing need to find alternative clean energy sources to fossil fuels, research into developing efficient fuel cells and batteries stands at the forefront of this grand effort. However, before mass commercialization, fundamental key issues need to be addressed. For example, fuel cells are subject to high catalyst costs and poor durability of the underlying carbon support. As a way to alleviate these issues, we have synthesized ultrathin one-dimensional (1D) alloy nanowires to probe the effect of composition, purity, and one-dimensionality upon the observed overall activity, performance, and durability. In terms of chemical composition, crystalline ultrathin PtM alloy nanowires (NWs) ('M' = Fe, Co, Ru, Cu, and Au) were generated and subsequently evaluated for the hydrogen oxidation reaction (HOR). Additionally, ternary-based catalysts were synthesized (PtRuFe) in order to analyze how chemical composition influences CO tolerance as well as methanol oxidation reaction (MOR) and formic acid oxidation reaction (FAOR) activities. In both cases, we utilized a sustainably mild, ambient wet-synthesis method for the fabrication of chemically pure and crystalline systems in order to fabricate ultrathin, homogeneous alloy NWs. Moreover, in these studies, our NW systems exhibit favorable synergistic electronic effects with respect to controls. To address another fundamental issue associated with the durability of fuel cells, we have synthesized various metal oxide and perovskite materials of different sizes and chemical compositions as supports for Pt nanoparticles (NPs). Specifically, we have demonstrated favorable metal support interactions between the Pt NPs and the SrRuO3 NP supports, which lead to increased MOR activity as compared with not only the other metal oxide supports tested but also the commercial Pt NP/C standard. In terms of Li-ion batteries, LiFePO4 materials have become increasingly popular as a cathode material due to the many benefits they possess including thermal stability, durability, low cost, and long life span. However, to broaden the general appeal of this material for practical electrochemical applications, it was useful to develop a relatively mild, reasonably simple synthesis method of this cathode material. We describe a generalizable, 2-step methodology of sustainably synthesizing LiFePO4 by incorporating a template-based, ambient, surfactantless, seedless, U-tube protocol in order to generate size and morphologically tailored, crystalline, phase-pure nanowires. Specifically, we demonstrate for the first time experimentally that the Fe-O3 chemical bond plays an important role in determining the overall conductivity of the material, an assertion which is further supported by recent "first-principles" calculations.

44 CFR 5.25 - Available materials.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 44 Emergency Management and Assistance 1 2011-10-01 2011-10-01 false Available materials. 5.25... Agency Information, Rules, Orders, Policies, and Similar Material § 5.25 Available materials. FEMA materials which are available under this subpart are as follows: (a) Final opinions and orders made in the...

44 CFR 5.25 - Available materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 44 Emergency Management and Assistance 1 2013-10-01 2013-10-01 false Available materials. 5.25... Agency Information, Rules, Orders, Policies, and Similar Material § 5.25 Available materials. FEMA materials which are available under this subpart are as follows: (a) Final opinions and orders made in the...

44 CFR 5.25 - Available materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 44 Emergency Management and Assistance 1 2012-10-01 2011-10-01 true Available materials. 5.25... Agency Information, Rules, Orders, Policies, and Similar Material § 5.25 Available materials. FEMA materials which are available under this subpart are as follows: (a) Final opinions and orders made in the...

Carpet in Schools: Myth and Reality.

ERIC Educational Resources Information Center

Chan, T. C.; Richardson, Michael D.; Jording, Cathy

2001-01-01

Carpet can serve as a type of finish over concrete, improves the acoustical environment, and helps build a more conducive, personalized learning environment. Problems associated with carpeting are related to raw materials, texture, cleaning materials, cost factors, moisture, and alleged contribution to poor indoor air quality. Recommendations are…

Raman imaging from microscopy to macroscopy: Quality and safety control of biological materials

USDA-ARS?s Scientific Manuscript database

Raman imaging can analyze biological materials by generating detailed chemical images. Over the last decade, tremendous advancements in Raman imaging and data analysis techniques have overcome problems such as long data acquisition and analysis times and poor sensitivity. This review article introdu...

Pathways into chronic multidimensional poverty amongst older people: a longitudinal study.

PubMed

Callander, Emily J; Schofield, Deborah J

2016-03-07

The use of multidimensional poverty measures is becoming more common for measuring the living standards of older people. However, the pathways into poverty are relatively unknown, nor is it known how this affects the length of time people are in poverty for. Using Waves 1 to 12 of the nationally representative Household, Income and Labour Dynamics in Australia (HILDA) survey, longitudinal analysis was undertaken to identify the order that key forms of disadvantage develop - poor health, low income and insufficient education attainment - amongst Australians aged 65 years and over in multidimensional poverty, and the relationship this has with chronic poverty. Path analysis and linear regression models were used. For all older people with at least a Year 10 level of education attainment earlier mental health was significantly related to later household income (p = 0.001) and wealth (p = 0.017). For all older people with at less than a Year 10 level of education attainment earlier household income was significantly related to later mental health (p = 0.021). When limited to those in multidimensional poverty who were in income poverty and also had poor health, older people generally fell into income poverty first and then developed poor health. The order in which income poverty and poor health were developed had a significant influence on the length of time older people with less than a Year 10 level of education attainment were in multidimensional poverty for. Those who developed poor health first then fell into income poverty spend significantly less time in multidimensional poverty (-4.90, p < .0001) than those who fell into income poverty then developed poor health. Knowing the order that different forms of disadvantage develop, and the influence this has on poverty entrenchment, is of use to policy makers wishing to provide interventions to prevent older people being in long-term multidimensional poverty.

78 FR 51213 - In the Matter of Certain Licensees Requesting Unescorted Access to Radioactive Material; Order...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-20

... license authorizes it to perform services on devices containing certain radioactive material for customers... Possess Sources Containing Radioactive Material Quantities of Concern,'' stated that ``service providers..., Fingerprinting Order, paragraph IC 1.c of the prior Order was superseded by the requirement that ``Service...

Optimizing tooth form with direct posterior composite restorations.

PubMed

Raghu, Ramya; Srinivasan, Raghu

2011-10-01

Advances in material sciences and technology have provided today's clinicians the strategies to transform the mechanistic approach of operative dentistry into a biologic philosophy. In the last three decades, composite resins have gone from being just an esthetically pleasing way of restoring Class III and Class IV cavities to become the universal material for both anterior and posterior situations as they closely mimic the natural esthetics while restoring the form of the human dentition. In order to enhance their success, clinicians have to rethink their protocol instead of applying the same restorative concepts and principles practiced with metallic restorations. Paralleling the evolution of posterior composite resin materials, cavity designs, restorative techniques and armamentarium have also developed rapidly to successfully employ composite resins in Class II situations. Most of the earlier problems with posterior composites such as poor wear resistance, polymerization shrinkage, postoperative sensitivity, predictable bonding to dentin, etc., have been overcome to a major extent. However, the clinically relevant aspect of achieving tight contacts in Class II situations has challenged clinicians the most. This paper reviews the evolution of techniques and recent developments in achieving predictable contacts with posterior composites. A Medline search was performed for articles on "direct posterior composite contacts." The keywords used were "contacts and contours of posterior composites." The reference list of each article was manually checked for additional articles of relevance.

Robust Catalysis on 2D Materials Encapsulating Metals: Concept, Application, and Perspective.

PubMed

Deng, Jiao; Deng, Dehui; Bao, Xinhe

2017-11-01

Great endeavors are undertaken to search for low-cost, rich-reserve, and highly efficient alternatives to replace precious-metal catalysts, in order to cut costs and improve the efficiency of catalysts in industry. However, one major problem in metal catalysts, especially nonprecious-metal catalysts, is their poor stability in real catalytic processes. Recently, a novel and promising strategy to construct 2D materials encapsulating nonprecious-metal catalysts has exhibited inimitable advantages toward catalysis, especially under harsh conditions (e.g., strong acidity or alkalinity, high temperature, and high overpotential). The concept, which originates from unique electron penetration through the 2D crystal layer from the encapsulated metals to promote a catalytic reaction on the outermost surface of the 2D crystal, has been widely applied in a variety of reactions under harsh conditions. It has been vividly described as "chainmail for catalyst." Herein, recent progress concerning this chainmail catalyst is reviewed, particularly focusing on the structural design and control with the associated electronic properties of such heterostructure catalysts, and also on their extensive applications in fuel cells, water splitting, CO 2 conversion, solar cells, metal-air batteries, and heterogeneous catalysis. In addition, the current challenges that are faced in fundamental research and industrial application, and future opportunities for these fantastic catalytic materials are discussed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Irradiation-Accelerated Corrosion of Reactor Core Materials. Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiao, Zhujie; Was, Gary; Bartels, David

2015-04-02

This project aims to understand how radiation accelerates corrosion of reactor core materials. The combination of high temperature, chemically aggressive coolants, a high radiation flux and mechanical stress poses a major challenge for the life extension of current light water reactors, as well as the success of most all GenIV concepts. Of these four drivers, the combination of radiation and corrosion places the most severe demands on materials, for which an understanding of the fundamental science is simply absent. Only a few experiments have been conducted to understand how corrosion occurs under irradiation, yet the limited data indicates that themore » effect is large; irradiation causes order of magnitude increases in corrosion rates. Without a firm understanding of the mechanisms by which radiation and corrosion interact in film formation, growth, breakdown and repair, the extension of the current LWR fleet beyond 60 years and the success of advanced nuclear energy systems are questionable. The proposed work will address the process of irradiation-accelerated corrosion that is important to all current and advanced reactor designs, but remains very poorly understood. An improved understanding of the role of irradiation in the corrosion process will provide the community with the tools to develop predictive models for in-reactor corrosion, and to address specific, important forms of corrosion such as irradiation assisted stress corrosion cracking.« less

Thermoelectric and thermospintronic transport in Dirac material-based nanostructures

NASA Astrophysics Data System (ADS)

Chang, Po-Hao

The growing need for power due to the rapid developments of the technologies has urged both engineers and scientists to study more sustainable types of energy. On the other hand, the improvement of our abilities although enable us, for example, to double the number of transistors in a dense integrated circuit approximately every two years (Moore's law), comes with side effect due to overheating. Taking advantage of thermoelectric effect has thus become one of the obvious solutions for the problems. But due to the poor efficiency of electricity-heat conversion, there are still challenges to be overcome in order to fully utilize the idea. In the past few years, the realization of graphene along with the discoveries of topological insulators (TI) which are both considered as Dirac material (DM) have offer alternative routs for improving the energy conversion efficiency through different approaches as well as novel quantum effects of materials themselves for investigation. The aim of this thesis is to present contributions to improving the efficiency of thermoelectric conversion as well as analyzing spin transport phenomena that occur in nano-devices. This thesis spans the areas of thermoelectric (TE) effect, spin-Seebeck effect (SSE) and the spin transport on the 3D topological insulator (TI). The different methods have been applied ranging from tight-binding (TB) approximation to density function theory (DFT) combined with non-equilibrium function (NEGF) techniques.

High-Throughput Synthesis and Structure of Zeolite ZSM-43 with Two-Directional 8-Ring Channels.

PubMed

Willhammar, Tom; Su, Jie; Yun, Yifeng; Zou, Xiaodong; Afeworki, Mobae; Weston, Simon C; Vroman, Hilda B; Lonergan, William W; Strohmaier, Karl G

2017-08-07

The aluminosilicate zeolite ZSM-43 (where ZSM = Zeolite Socony Mobil) was first synthesized more than 3 decades ago, but its chemical structure remained unsolved because of its poor crystallinity and small crystal size. Here we present optimization of the ZSM-43 synthesis using a high-throughput approach and subsequent structure determination by the combination of electron crystallographic methods and powder X-ray diffraction. The synthesis required the use of a combination of both inorganic (Cs + and K + ) and organic (choline) structure-directing agents. High-throughput synthesis enabled a screening of the synthesis conditions, which made it possible to optimize the synthesis, despite its complexity, in order to obtain a material with significantly improved crystallinity. When both rotation electron diffraction and high-resolution transmission electron microscopy imaging techniques are applied, the structure of ZSM-43 could be determined. The structure of ZSM-43 is a new zeolite framework type and possesses a unique two-dimensional channel system limited by 8-ring channels. ZSM-43 is stable upon calcination, and sorption measurements show that the material is suitable for adsorption of carbon dioxide as well as methane.

Phase transformation mechanism in lithium manganese nickel oxide revealed by single-crystal hard X-ray microscopy

DOE PAGES

Kuppan, Saravanan; Xu, Yahong; Liu, Yijin; ...

2017-02-01

Understanding the reaction pathway and kinetics of solid-state phase transformation is critical in designing advanced electrode materials with better performance and stability. Despite the first-order phase transition with a large lattice mismatch between the involved phases, spinel LiMn 1.5Ni 0.5O 4 is capable of fast rate even at large particle size, presenting an enigma yet to be understood. The present study uses advanced two-dimensional and three-dimensional nano-tomography on a series of well-formed LixMn 1.5Ni 0.5O 4 (0 ≤ x ≤ 1) crystals to visualize the mesoscale phase distribution, as a function of Li content at the sub-particle level. Inhomogeneity alongmore » with the coexistence of Li-rich and Li-poor phases are broadly observed on partially delithiated crystals, providing direct evidence for a concurrent nucleation and growth process instead of a shrinking-core or a particle-by-particle process. As a result, superior kinetics of (100) facets at the vertices of truncated octahedral particles promote preferential delithiation, whereas the observation of strain-induced cracking suggests mechanical degradation in the material.« less

Selenite sorption by carbonate substituted apatite

DOE PAGES

Moore, Robert C.; Rigali, Mark J.; Brady, Patrick

2016-08-31

The sorption of selenite, SeO 3 2–, by carbonate substituted hydroxylapatite was investigated using batch kinetic and equilibrium experiments. The carbonate substituted hydroxylapatite was prepared by a precipitation method and characterized by SEM, XRD, FT-IR, TGA, BET and solubility measurements. The material is poorly crystalline, contains approximately 9.4% carbonate by weight and has a surface area of 210.2 m 2/g. Uptake of selenite by the carbonated hydroxylapatite was approximately an order of magnitude higher than the uptake by uncarbonated hydroxylapatite reported in the literature. Distribution coefficients, K d, determined for the carbonated apatite in this work ranged from approximately 4200more » to over 14,000 L/kg. A comparison of the results from kinetic experiments performed in this work and literature kinetic data indicates the carbonated apatite synthesized in this study sorbed selenite 23 times faster than uncarbonated hydroxylapatite based on values normalized to the surface area of each material. Furthermore, the results indicate carbonated apatite is a potential candidate for use as a sorbent for pump-and-treat technologies, soil amendments or for use in permeable reactive barriers for the remediation of selenium contaminated sediments and groundwaters.« less

Difficulties in fumonisin determination: the issue of hidden fumonisins.

PubMed

Dall'Asta, Chiara; Mangia, Mattia; Berthiller, Franz; Molinelli, Alexandra; Sulyok, Michael; Schuhmacher, Rainer; Krska, Rudolf; Galaverna, Gianni; Dossena, Arnaldo; Marchelli, Rosangela

2009-11-01

In this paper, the results obtained by five independent methods for the quantification of fumonisins B(1), B(2), and B(3) in raw maize are reported. Five naturally contaminated maize samples and a reference material were analyzed in three different laboratories. Although each method was validated and common calibrants were used, a poor agreement about fumonisin contamination levels was obtained. In order to investigate the interactions among analyte and matrix leading to this lack of consistency, the occurrence of fumonisin derivatives was checked. Significant amounts of hidden fumonisins were detected for all the considered samples. Furthermore, the application of an in vitro digestion protocol to raw maize allowed for a higher recovery of native fumonisins, suggesting that the interaction occurring among analytes and matrix macromolecules is associative rather than covalent. Depending on the analytical method as well as the maize sample, only 37-68% of the total fumonisin concentrations were found to be extractable from the samples. These results are particularly impressive and significant in the case of the certified reference material, underlying the actual difficulties in ascertaining the trueness of a method for fumonisin determination, opening thus an important issue for risk assessment.

Boron removal by a composite sorbent: Polyethylenimine/tannic acid derivative immobilized in alginate hydrogel beads.

PubMed

Bertagnolli, Caroline; Grishin, Andrey; Vincent, Thierry; Guibal, Eric

2017-03-21

A novel composite material was prepared by the grafting of tannic acid on polyethylenimine (PEI), which allows an efficient sorption of boron (sorption capacity close to 0.89 mmol B g -1 ). The encapsulation of this chelating sorbent (finely crushed) facilitates its use (readily solid/liquid separation, use in fixed-bed columns) at the expense of a loss in sorption capacity (proportionally decreased by the introduction of alginate having poor efficiency for boron uptake). Sorption isotherms are modeled using the Langmuir equation, while the kinetic profiles are presented a good fit by pseudo-second order rate equation. In addition, the encapsulating matrix introduces supplementary resistance to intraparticle diffusion, especially when the resin is dried without control: freeze-drying partially limits this effect. The stability (at long-term storage) of the sorbent is improved when the sorbent is stored under nitrogen atmosphere. The presence of an excess of NaCl was investigated. The degradation of the hydrogel (by ion-exchange of Ca(II) with Na(I)) leads to a decrease in the sorption performance of composite material but the action of Ca(II) ions in the solutions re-stabilizes the hydrogel.

Physicochemical properties of aerosol released in the case of a fire involving materials used in the nuclear industry.

PubMed

Ouf, F-X; Mocho, V-M; Pontreau, S; Wang, Z; Ferry, D; Yon, J

2015-01-01

For industrial concerns, and more especially for nuclear applications, the characterization of soot is essential for predicting the behaviour of containment barriers in fire conditions. This study deals with the characterization (emission factor, composition, size, morphology, microstructure) of particles produced during thermal degradation of materials found in nuclear facilities (electrical cables, polymers, oil and solvents). Small-scale experiments have been conducted for oxygen concentrations [O2] ranging from 15% to 21% in order to imitate the oxygen depletion encountered during a confined fire. Particles denote distinct shapes, from aggregates composed of monomers with diameters ranging from 31.2 nm to 52.8 nm, to compact nanoparticles with diameters ranging from 15 nm to 400 nm, and their composition strongly depends on fuel type. Despite the organic to total carbon ratio (OC/TC), their properties are poorly influenced by the decrease in [O2]. Finally, two empirical correlations are proposed for predicting the OC/TC ratio and the monomer diameter, respectively, as a function of the fuel's carbon to hydrogen ratio and the emission factor. Copyright © 2014 Elsevier B.V. All rights reserved.

Bacterial Cellular Materials as Precursors of Chloroform

NASA Astrophysics Data System (ADS)

Wang, J.; Ng, T.; Zhang, Q.; Chow, A. T.; Wong, P.

2011-12-01

The environmental sources of chloroform and other halocarbons have been intensively investigated because their effects of stratospheric ozone destruction and environmental toxicity. It has been demonstrated that microorganisms could facilitate the biotic generation of chloroform from natural organic matters in soil, but whether the cellular materials itself also serves as an important precursor due to photo-disinfection is poorly known. Herein, seven common pure bacterial cultures (Acinetobacter junii, Aeromonas hydrophila, Bacillus cereus, Bacillus substilis, Escherichia coli, Shigella sonnei, Staphylococcus sciuri) were chlorinated to evaluate the yields of chloroform, dibromochloromethane, dichlorobromomethane, and bromoform. The effects of bromide on these chemical productions and speciations were also investigated. Results showed that, on average, 5.64-36.42 μg-chloroform /mg-C were generated during the bacterial chlorination, in similar order of magnitude to that generated by humic acid (previously reported as 78 μg-chloroform/mg-C). However, unlike humic acid in water chlorination, chloroform concentration did not simply increase with the total organic carbon in water mixture. In the presence of bromide, the yield of brominated species responded linearly to the bromide concentration. This study provides useful information to understand the contributions of chloroform from photodisinfection processes in coastal environments.

Frequent genomic imbalances suggest commonly altered tumour genes in human hepatocarcinogenesis

PubMed Central

Niketeghad, F; Decker, H J; Caselmann, W H; Lund, P; Geissler, F; Dienes, H P; Schirmacher, P

2001-01-01

Hepatocellular carcinoma (HCC) is one of the most frequent-occurring malignant tumours worldwide, but molecular changes of tumour DNA, with the exception of viral integrations and p53 mutations, are poorly understood. In order to search for common macro-imbalances of genomic tumour DNA, 21 HCCs and 3 HCC-cell lines were characterized by comparative genomic hybridization (CGH), subsequent database analyses and in selected cases by fluorescence in situ hybridization (FISH). Chromosomal subregions of 1q, 8q, 17q and 20q showed frequent gains of genomic material, while losses were most prevalent in subregions of 4q, 6q, 13q and 16q. Deleted regions encompass tumour suppressor genes, like RB-1 and the cadherin gene cluster, some of them previously identified as potential target genes in HCC development. Several potential growth- or transformation-promoting genes located in chromosomal subregions showed frequent gains of genomic material. The present study provides a basis for further genomic and expression analyses in HCCs and in addition suggests chromosome 4q to carry a so far unidentified tumour suppressor gene relevant for HCC development. © 2001 Cancer Research Campaign http://www.bjcancer.com PMID:11531255

Consumer Problems of the Poor. Expanded Programs of Consumer Education. (Series)

ERIC Educational Resources Information Center

New York State Education Dept., Albany. Bureau of Secondary Curriculum Development.

The fourth in a series of modules--Expanded Programs of Consumer Education--this material is designed to help the poor make better use of their income and to stimulate those of high income to a greater understanding of the problems of their fellow-citizens. The modules are prepared for high school students as separate publications to provide…

Cluster Randomized-Controlled Trial of Interventions to Improve Health for Adults with Intellectual Disability Who Live in Private Dwellings

ERIC Educational Resources Information Center

Lennox, Nicholas; Bain, Chris; Rey-Conde, Therese; Taylor, Miriam; Boyle, Frances M.; Purdie, David M.; Ware, Robert S.

2010-01-01

Background: People with intellectual disability who live in the community often have poor health and healthcare, partly as a consequence of poor communication, recall difficulties and incomplete patient health information. Materials and Methods: A cluster randomized-controlled trial with 2 x 2 factorial design was conducted with adults with…

Petrology and thermal history of type IA chondrules in the Semarkona (LL3.0) chondrite

NASA Technical Reports Server (NTRS)

Jones, R. H.; Scott, E. R. D.

1989-01-01

Detailed petrologic studies have been made of 15 type IA, Fe-poor, porphyritic olivine chondrules in Semarkona (LL3.0). Major and minor element concentrations in olivines, pyroxenes, and mesostases, and bulk composition so the chondrules are measured along with zoning profiles in the olivine and pyroxene crystals. The mineral compositions and textures are best interpreted in terms of closed system crystallization in which the olivines and pyroxenes crystallized in situ from a melt corresponding to the bulk composition of the chondrule. Relict olivine grains are not found in the chondrules. Crystallization probably occurred at a cooling rate of the order of 1000 C/hr. Precursor materials of the chondrules were composed of two components, one refractory Ca-, Al-, and Ti-rich, and one less refractory Si-, Fe-, Cr-, and Mn-rich. The evidence is consistent with Semarkona being one of the least metamorphosed ordinary chondrites.

Diatoms: a biotemplating approach to fabricating drug delivery reservoirs.

PubMed

Chao, Joshua T; Biggs, Manus J P; Pandit, Abhay S

2014-11-01

Biotemplating is a rapidly expanding subfield that utilizes nature-inspired systems and structures to create novel functional materials, and it is through these methods that the limitations of current engineering practices may be advanced. The diatom is an exceptional template for drug delivery applications, owing largely to its highly-ordered pores, large surface area, species-specific architecture, and flexibility for surface modifications. Diatoms have been studied in a wide range of biomedical applications and their potential as the next frontier of drug delivery has yet to be fully exploited. In this editorial, the authors aim to review the use of diatoms in the delivery of poorly water-soluble drugs as reported in the literature, discuss the progress and advancements that have been made thus far, identify the shortcomings and limitations in the field, and, lastly, present their expert opinion and convey the future outlook on biotemplating approaches for drug delivery.

Evaluating bacterial pathogen DNA preservation in museum osteological collections

PubMed Central

Barnes, Ian; Thomas, Mark G

2005-01-01

Reports of bacterial pathogen DNA sequences obtained from archaeological bone specimens raise the possibility of greatly improving our understanding of the history of infectious diseases. However, the survival of pathogen DNA over long time periods is poorly characterized, and scepticism remains about the reliability of these data. In order to explore the survival of bacterial pathogen DNA in bone specimens, we analysed samples from 59 eighteenth and twentieth century individuals known to have been infected with either Mycobacterium tuberculosis or Treponema pallidum. No reproducible evidence of surviving pathogen DNA was obtained, despite the use of extraction and PCR-amplification methods determined to be highly sensitive. These data suggest that previous studies need to be interpreted with caution, and we propose that a much greater emphasis is placed on understanding how pathogen DNA survives in archaeological material, and how its presence can be properly verified and used. PMID:16608682

Rutile TiO2 Mesocrystals as Sulfur Host for High-Performance Lithium-Sulfur Batteries.

PubMed

Sun, Qingqing; Chen, Kaixiang; Liu, Yubin; Li, Yafeng; Wei, Mingdeng

2017-11-16

Although lithium-sulfur (Li-S) batteries are among the most promising rechargeable batteries in the field of energy-storage devices, their poor cycling performance restricts their potential applications. Polar materials can improve the cycling stability owing to their inherent strong chemical interaction with polysulfides. Herein, novel rutile TiO 2 mesocrystals (RTMs) are employed as the host for sulfur in Li-S batteries; the RTMs display a stable cycling performance with a capacity retention of 64 % and a small average capacity decay rate of 0.12 % per cycle over 300 cycles at 1 C rate. The good electrochemical properties are attributed to the interior ordered nanopores of the RTMs, which can effectively limit the dissolution of polysulfides, and the ultrafine nanowires in RTMs, which shorten the path for lithium-ion transport effectively. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, Xiang; Zhang, Shuai; Jiao, Fang

Two-step nucleation pathways in which disordered, amorphous, or dense liquid states precede appearance of crystalline phases have been reported for a wide range of materials, but the dynamics of such pathways are poorly understood. Moreover, whether these pathways are general features of crystallizing systems or a consequence of system-specific structural details that select for direct vs two-step processes is unknown. Using atomic force microscopy to directly observe crystallization of sequence-defined polymers, we show that crystallization pathways are indeed sequence dependent. When a short hydrophobic region is added to a sequence that directly forms crystalline particles, crystallization instead follows a two-stepmore » pathway that begins with creation of disordered clusters of 10-20 molecules and is characterized by highly non-linear crystallization kinetics in which clusters transform into ordered structures that then enter the growth phase. The results shed new light on non-classical crystallization mechanisms and have implications for design of self-assembling polymer systems.« less

Significant improvement in Mn2O3 transition metal oxide electrical conductivity via high pressure

PubMed Central

Hong, Fang; Yue, Binbin; Hirao, Naohisa; Liu, Zhenxian; Chen, Bin

2017-01-01

Highly efficient energy storage is in high demand for next-generation clean energy applications. As a promising energy storage material, the application of Mn2O3 is limited due to its poor electrical conductivity. Here, high-pressure techniques enhanced the electrical conductivity of Mn2O3 significantly. In situ synchrotron micro X-Ray diffraction, Raman spectroscopy and resistivity measurement revealed that resistivity decreased with pressure and dramatically dropped near the phase transition. At the highest pressure, resistivity reduced by five orders of magnitude and the sample showed metal-like behavior. More importantly, resistivity remained much lower than its original value, even when the pressure was fully released. This work provides a new method to enhance the electronic properties of Mn2O3 using high-pressure treatment, benefiting its applications in energy-related fields. PMID:28276479

[Immunohistochemistry in the diagnosis of sarcomas].

PubMed

Decouvelaere, Anne-Valérie

2015-01-01

Immunohistochemistry (IHC) is essential in the diagnosis of soft tissue tumor and must rely on good quality technic. Among useful antibodies, it is important to distinguish those with a poor specificity required in order to establish the broad lineage, from those with high specificity, which may lead straightforward towards the entity. Diagnostically useful antibodies such as myogenin, ALK1 and DOG1 have been recently completed by MUC4 and STAT6 which show good sensitivity and specificity in the diagnosis of low-grade fibromyxoid sarcoma and solitary fibrous tumor respectively. ERG is also an interesting antibody. However, it is not completely specific of vascular tumors. Moreover, available material is often limited because of the increase of microbiopsy specimens. Therefore, it is mandatory to optimize this precious tissue by using these new antibodies, especially because molecular technics are increasingly performed in addition to IHC. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Time-resolved electric force microscopy of charge traps in polycrystalline pentacene films

NASA Astrophysics Data System (ADS)

Jaquith, Michael; Muller, Erik; Marohn, John

2006-03-01

The microscopic mechanisms by which charges trap in organic electronic materials are poorly understood. Muller and Marohn recently showed that electric force microscopy (EFM) can be used to image trapped charge in working pentacene thin-film transistors [E. M. Muller et al, Adv. Mater. 17 1410 (2005)]. We have extended their work by imaging trapped charge in pentacene films with much larger grains. In contrast to the previous study in which charge was found to trap inhomogeneously throughout the transistor gap, we find microscopic evidence for a new trapping mechanism in which charges trap predominantly at the pentacene/metal interface in large-grained devices. We have also made localized measurements of the trap growth over time by performing pulsed-gate EFM experiments. Integrated-rate kinetics data supports a charge trap mechanism which is second order in holes, e.g., holes trap in pairs, although the charge-trapping rate appears to depend on gate voltage.

Study of cyclic thermal aging of tube type receivers as a function of the duration of the cycle

NASA Astrophysics Data System (ADS)

Setien, Eneko; Fernández-Reche, Jesús; Ariza, María Jesús; Álvarez-de-Lara, Mónica

2017-06-01

The tube type receivers are exposed to variable duration cyclic operating conditions, which can jeopardize its reliability, and make it hard to estimate its long term performance. The designers have to deal with this problem and estimate the receiver long term performance based on the poor available litterature and the data sheets of the material. In order to help the designer better estimate the performance of the receivers, in this paper the cyclic thermal aging is analyzed as a function of the cycle duration. For this purpose, coated and uncoated Inconel alloy 625 tubular samples, similar to those used in the commercial receivers, are cyclically aged with different thermal cycle duration. The aging of these samples has been analyzed by means of oxidation kinetics, microstructure examination and mechanical and optical properties. The effect of the thermal cycle duration is studied and discussed by comparison of the results.

Materials education activities

NASA Technical Reports Server (NTRS)

Ries, Heidi R.; Harris, Jonice; Leake, Woodrow W.; Bunnell, L. Roy; Berrettini, Robert

1993-01-01

Last year, at NEW: Update '91, a panel discussion was held to address the unique difficulties of attracting and retaining minorities and women in technical studies. Unfortunately, retention in technical majors is a problem of varying proportions for the entire student population, and must be improved in order to maintain the strength of the nation's industrial base. To investigate the cause of student attrition in technical majors, in-depth interviews of both current and former (non-graduating) engineering students at four colleges and universities in Colorado were conducted by Hewitt and Seymour. They found that there was no significant difference in the level of high school preparation and undergraduate academic performance in these two groups, despite the prevailing faculty perception that most students who switch from technical to nontechnical majors were underprepared. The majority of engineering students who changed majors reported that they were turned off by science, while one-third complained of poor teaching.

Bonding structure in amorphous carbon nitride: A spectroscopic and nuclear magnetic resonance study

NASA Astrophysics Data System (ADS)

Sánchez-López, J. C.; Donnet, C.; Lefèbvre, F.; Fernández-Ramos, C.; Fernández, A.

2001-07-01

Since the prediction of Liu and Cohen [Science 245, 841 (1989)] of the potential extraordinary mechanical properties of crystalline β-C3N4, many authors have attempted its synthesis. However, in most cases, the obtained materials are amorphous phases with a complex bonding structure. Their characterization is complicated due to the absence of a reference compound, the lack of long-range order, and the poor knowledge about their bonding structure. In this article, we present 1H, 13C, and 15N solid-state nuclear magnetic resonance (NMR) measurements for the determination of the bonding types in amorphous CNx films. NMR measurements do not require long-range order and are able to clearly identify the signals from the sp2- and sp3-bonded phases. The analysis of the data obtained by other characterization techniques, such as infrared spectroscopy, x-ray photoelectron spectroscopy, electron energy-loss spectroscopy, and x-ray absorption near-edge spectroscopy on the same sample, based on the information acquired by NMR, enables the description of a structure model for the studied amorphous-CNx phase prepared by dc-magnetron sputtering and to revise the interpretation found in the literature.

Enhanced field-dependent conductivity of magnetorheological gels with low-doped carbon nanotubes

NASA Astrophysics Data System (ADS)

Qu, Hang; Yu, Miao; Fu, Jie; Yang, Pingan; Liu, Yuxuan

2017-10-01

Magnetorheological gels (MRG) exhibit field-dependent conductivity and controllable mechanical properties. In order to extend their application field, filling a large number of traditional conductive materials is the most common means to enhance the poor conductivity of MRG. In this study, the conductivity of MRG is improved by low-doped carbon nanotubes (CNTs). The influence of CNTs on the magnetoresistance of MRG is discussed from two aspects—the improvement in electrical conductivity and the magnetic sensitivity of conductivity variation. The percolation threshold of CNTs in MRG should be between 1 wt% and 2 wt%. The conductivity of a 4 wt% CNT-doped sample increases more than 28 000 times compared with pure MRG. However, there is a cliff-like drop for the range and rate of conductivity variation when the doping amount of CNTs is between 3 wt% and 4 wt%. Therefore, it is concluded that the optimal mass fraction of CNTs is 3%, which can maintain a suitable variation range and a strong conductivity. Compared with pure MRG, its conductivity increases by at least two orders of magnitude. Finally, a sketch of particle motion simulation is developed to understand the improving mechanism and the effect of CNTs.

Home Economics Reading Skills: Problems and Selected References.

ERIC Educational Resources Information Center

Cranney, A. Garr; And Others

Home economics presents at least eight problems to secondary school reading teachers. These problems include poor readers, difficult reading material, lack of reading materials, teachers' lack of training in reading instruction, scarce information about home economics for reading teachers, diversity of the home economics field (requiring a wide…

Mesoporous Silica Molecular Sieve based Nanocarriers: Transpiring Drug Dissolution Research.

PubMed

Pattnaik, Satyanarayan; Pathak, Kamla

2017-01-01

Improvement of oral bioavailability through enhancement of dissolution for poorly soluble drugs has been a very promising approach. Recently, mesoporous silica based molecular sieves have demonstrated excellent properties to enhance the dissolution velocity of poorly water-soluble drugs. Current research in this area is focused on investigating the factors influencing the drug release from these carriers, the kinetics of drug release and manufacturing approaches to scale-up production for commercial manufacture. This comprehensive review provides an overview of different methods adopted for synthesis of mesoporous materials, influence of processing factors on properties of these materials and drug loading methods. The drug release kinetics from mesoporous silica systems, the manufacturability and stability of these formulations are reviewed. Finally, the safety and biocompatibility issues related to these silica based materials are discussed. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Health literacy and ophthalmic patient education

PubMed Central

Muir, Kelly W.; Lee, Paul P.

2010-01-01

In 1997, Ebrahimzadeh, Davalos and Lee wrote in this journal that only 32% of the ophthalmic patient educational materials reviewed were written at or below the recommended eighth grade reading level. Since that time, the National Assessment of Adult Literacy found that more than one third of adult Americans possess only basic or below basic health literacy skills, defined as the ability to understand written information in a healthcare setting. Subsequently, investigators have shown that poor health literacy skills are associated with poor prescription medication adherence, increased hospital admissions and increased mortality. We review the readability of currently available ophthalmic educational materials, with particular attention to the health literacy status of the patient population for which the materials are intended. Examples of prose at various readability levels are provided. Optimizing patient education and improving clinical outcomes requires understanding the attributes that the patient brings to the patient–physician relationship, including health literacy. PMID:20650503

Quantifying Nanoscale Order in Amorphous Materials via Fluctuation Electron Microscopy

ERIC Educational Resources Information Center

Bogle, Stephanie Nicole

2009-01-01

Fluctuation electron microscopy (FEM) has been used to study the nanoscale order in various amorphous materials. The method is explicitly sensitive to 3- and 4-body atomic correlation functions in amorphous materials; this is sufficient to establish the existence of structural order on the nanoscale, even when the radial distribution function…

Measurement and modeling of short and medium range order in amorphous Ta 2O 5 thin films

DOE PAGES

Shyam, Badri; Stone, Kevin H.; Bassiri, Riccardo; ...

2016-08-26

Here, amorphous films and coatings are rapidly growing in importance. Yet, there is a dearth of high-quality structural data on sub-micron films. Not understanding how these materials assemble at atomic scale limits fundamental insights needed to improve their performance. Here, we use grazing-incidence x-ray total scattering measurements to examine the atomic structure of the top 50–100 nm of Ta 2O 5 films; mirror coatings that show high promise to significantly improve the sensitivity of the next generation of gravitational-wave detectors. Our measurements show noticeable changes well into medium range, not only between crystalline and amorphous, but also between as-deposited, annealedmore » and doped amorphous films. It is a further challenge to quickly translate the structural information into insights into mechanisms of packing and disorder. Here, we illustrate a modeling approach that allows translation of observed structural features to a physically intuitive packing of a primary structural unit based on a kinked Ta-O-Ta backbone. Our modeling illustrates how Ta-O-Ta units link to form longer 1D chains and even 2D ribbons, and how doping and annealing influences formation of 2D order. We also find that all the amorphousTa 2O 5 films studied in here are not just poorly crystalline but appear to lack true 3D order.« less

Seven Years Later: Effects of a Neighborhood Mobility Program on Poor Black and Latino Adults' Well-Being

ERIC Educational Resources Information Center

Fauth, Rebecca C.; Leventhal, Tama; Brooks-Gunn, Jeanne

2008-01-01

This study explored program effects on adults' well-being seven years following the implementation of a court-ordered neighborhood mobility program. Low-income black and Latino adults residing in poor, segregated neighborhoods in Yonkers, New York were randomly selected to relocate to publicly funded town-houses in middle-class neighborhoods…

The Effect of Script on Poor Readers' Sensitivity to Dynamic Visual Stimuli

ERIC Educational Resources Information Center

Kim, Jeesun; Davis, Chris; Burnham, Denis; Luksaneeyanawin, Sudaporn

2004-01-01

The current research examined performance of good and poor readers of Thai on two tasks that assess sensitivity to dynamic visual displays. Readers of Thai, a complex alphabetic script that nonetheless has a regular orthography, were chosen in order to contrast patterns of performance with readers of Korean Hangul (a similarly regular language but…

Planning Behaviour in Good and Poor Readers

ERIC Educational Resources Information Center

Mahapatra, Shamita

2016-01-01

A group of 50 good readers and a group of 50 poor readers of Grade 5 matched for age and intelligence and selected on the basis of their proficiency in reading comprehension were tested for their competence in word reading and the process of planning at three different levels, namely, perceptual, memory and conceptual in order to study the…

FAST TRACK COMMUNICATION: High material efficiency found in electrophoretic deposition of conjugated polymer

NASA Astrophysics Data System (ADS)

Tada, Kazuya; Onoda, Mitsuyoshi

2009-09-01

The material efficiency of electrophoretic deposition of a fluorene-based conjugated polymer, poly[(9,9-dioctyl-2,7-divinylenefluorenylene)-alt-{2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylene}] (PDOF-MEHPV), from suspensions with a mixture of acetonitrile and toluene as dispersant is studied. It has been found that the recovery rate of the electrophoretic deposition from a suspension containing 90% of the poor solvent acetonitrile reaches 98%. Although the recovery rate decreases with decreasing acetonitrile content, almost 70% of the polymer can be deposited on the substrates from the suspension containing equivalent volumes of the good and poor solvents by electrophoretic deposition, from which smooth and transparent films suitable for electronic devices are obtained.

A novel porous scaffold fabrication technique for epithelial and endothelial tissue engineering.

PubMed

McHugh, Kevin J; Tao, Sarah L; Saint-Geniez, Magali

2013-07-01

Porous scaffolds have the ability to minimize transport barriers for both two- (2D) and three-dimensional tissue engineering. However, current porous scaffolds may be non-ideal for 2D tissues such as epithelium due to inherent fabrication-based characteristics. While 2D tissues require porosity to support molecular transport, pores must be small enough to prevent cell migration into the scaffold in order to avoid non-epithelial tissue architecture and compromised function. Though electrospun meshes are the most popular porous scaffolds used today, their heterogeneous pore size and intense topography may be poorly-suited for epithelium. Porous scaffolds produced using other methods have similar unavoidable limitations, frequently involving insufficient pore resolution and control, which make them incompatible with 2D tissues. In addition, many of these techniques require an entirely new round of process development in order to change material or pore size. Herein we describe "pore casting," a fabrication method that produces flat scaffolds with deterministic pore shape, size, and location that can be easily altered to accommodate new materials or pore dimensions. As proof-of-concept, pore-cast poly(ε-caprolactone) (PCL) scaffolds were fabricated and compared to electrospun PCL in vitro using canine kidney epithelium, human colon epithelium, and human umbilical vein endothelium. All cell types demonstrated improved morphology and function on pore-cast scaffolds, likely due to reduced topography and universally small pore size. These results suggest that pore casting is an attractive option for creating 2D tissue engineering scaffolds, especially when the application may benefit from well-controlled pore size or architecture.

Double-tagged fluorescent bacterial bioreporter for the study of polycyclic aromatic hydrocarbon diffusion and bioavailability.

PubMed

Tecon, Robin; Binggeli, Olivier; van der Meer, Jan R

2009-09-01

Bacterial degradation of polycyclic aromatic hydrocarbons (PAHs), ubiquitous contaminants from oil and coal, is typically limited by poor accessibility of the contaminant to the bacteria. In order to measure PAH availability in complex systems, we designed a number of diffusion-based assays with a double-tagged bacterial reporter strain Burkholderia sartisoli RP037-mChe. The reporter strain is capable of mineralizing phenanthrene (PHE) and induces the expression of enhanced green fluorescent protein (eGFP) as a function of the PAH flux to the cell. At the same time, it produces a second autofluorescent protein (mCherry) in constitutive manner. Quantitative epifluorescence imaging was deployed in order to record reporter signals as a function of PAH availability. The reporter strain expressed eGFP proportionally to dosages of naphthalene or PHE in batch liquid cultures. To detect PAH diffusion from solid materials the reporter cells were embedded in 2 cm-sized agarose gel patches, and fluorescence was recorded over time for both markers as a function of distance to the PAH source. eGFP fluorescence gradients measured on known amounts of naphthalene or PHE served as calibration for quantifying PAH availability from contaminated soils. To detect reporter gene expression at even smaller diffusion distances, we mixed and immobilized cells with contaminated soils in an agarose gel. eGFP fluorescence measurements confirmed gel patch diffusion results that exposure to 2-3 mg lampblack soil gave four times higher expression than to material contaminated with 10 or 1 (mg PHE) g(-1).

High Temperature Polymeric Materials for Space Transportation Propulsion Applications

NASA Technical Reports Server (NTRS)

Meador, Michael A.; Campbell, Sandi G.; Chuang, Kathy C.; Scheimann, Daniel A.; Mintz, Eric; Hylton, Donald; Veazie, David; Criss, James; Kollmansberg, Ron; Tsotsis, Tom

2003-01-01

High temperature polymer matrix composites are attractive materials for space transporation propulsion systems because of their low density and high specific strength. However, the relatively poor stability and processability of these materials can render them unsuitable for many of these applications. New polymeric materials have been developed under the Propulsion Research and Technology Program through the use of novel resin chemistry and nanotechnology. These new materials can significantly enhance the durability and weight and improve the processability and affordability of propulsion components for advanced space transportation systems.

Microwave-assisted extraction and quantitative LC/ID-MS measurement of total choline and free carnitine in food standard reference materials.

PubMed

Phillips, Melissa M; Sander, Lane C

2012-01-01

The Stakeholder Panel on Infant Formula and Adult Nutritionals of AOAC INTERNATIONAL has declared both choline and carnitine to be priority nutrients in infant formulas, and ongoing efforts exist to develop or improve Official Methods of Analysis for these nutrients. As a result, matrix-based certified reference materials are needed with assigned values for these compounds. In this work, traditional acid and enzymatic hydrolysis procedures were compared to microwave-assisted acid hydrolysis, and conditions optimized to provide complete sample hydrolysis and recovery of total choline from four food standard reference materials (SRMs): whole milk powder, whole egg powder, infant formula, and soy flour. The extracts were analyzed using LC on a mixed-mode column (simultaneous RP and ion exchange) with isotope dilution-MS detection to achieve simultaneous quantification of total choline and free carnitine. Total choline has been determined in these four food matrixes with excellent precision (0.65 to 2.60%) and accuracy, as confirmed by use of SRM 1849 Infant/Adult Nutritional Formula as a control material. Free carnitine has been determined in two of these food matrixes with excellent precision (0.69 to 2.19%) and accuracy, as confirmed by use of SRM 1849 Infant/Adult Nutritional Formula as a control material. Limitations in simultaneous determination of total choline and free carnitine resulted from extreme differences in concentration of the two components in egg powder and soy flour (at least three orders of magnitude). Samples required dilution to prevent poor LC peak shape, which caused decreased precision in the determination of low concentrations of free carnitine. Despite this limitation, the described method yields results comparable to current AOAC Official Method 999.14 Choline in Infant Formula, with a decrease of more than 2 h in sample preparation time.

Biocompatibility and characterization of a Kolsterised® medical grade cobalt-chromium-molybdenum alloy

PubMed Central

Conti, Malcolm Caligari; Karl, Andreas; Wismayer, Pierre Schembri; Buhagiar, Joseph

2014-01-01

High failure rates of cobalt-chromium-molybdenum (Co-Cr-Mo) metal-on-metal hip prosthesis were reported by various authors, probably due to the alloy's limited hardness and tribological properties. This thus caused the popularity of the alloy in metal-on-metal hip replacements to decrease due to its poor wear properties when compared with other systems such as ceramic-on-ceramic. S-phase surface engineering has become an industry standard when citing surface hardening of austenitic stainless steels. This hardening process allows the austenitic stainless steel to retain its corrosion resistance, while at the same time also improving its hardness and wear resistance. By coupling S-phase surface engineering, using the proprietary Kolsterising® treatment from Bodycote Hardiff GmbH, that is currently being used mainly on stainless steel, with Co-Cr-Mo alloys, an improvement in hardness and tribological characteristics is predicted. The objective of this paper is to analyze the biocompatibility of a Kolsterised® Co-Cr-Mo alloy, and to characterize the material surface in order to show the advantages gained by using the Kolsterised® material relative to the original untreated alloy, and other materials. This work has been performed on 3 fronts including; Material characterization, “In-vitro” corrosion testing, and Biological testing conforming to BS EN ISO 10993–18:2009 - Biological evaluation of medical devices. Using these techniques, the Kolsterised® cobalt-chromium-molybdenum alloys were found to have good biocompatibility and an augmented corrosion resistance when compared with the untreated alloy. The Kolsterised® samples also showed a 150% increase in surface hardness over the untreated material thus predicting better wear properties. PMID:24451266

Biocompatibility and characterization of a Kolsterised(®) medical grade cobalt-chromium-molybdenum alloy.

PubMed

Conti, Malcolm Caligari; Karl, Andreas; Wismayer, Pierre Schembri; Buhagiar, Joseph

2014-01-01

High failure rates of cobalt-chromium-molybdenum (Co-Cr-Mo) metal-on-metal hip prosthesis were reported by various authors, probably due to the alloy's limited hardness and tribological properties. This thus caused the popularity of the alloy in metal-on-metal hip replacements to decrease due to its poor wear properties when compared with other systems such as ceramic-on-ceramic. S-phase surface engineering has become an industry standard when citing surface hardening of austenitic stainless steels. This hardening process allows the austenitic stainless steel to retain its corrosion resistance, while at the same time also improving its hardness and wear resistance. By coupling S-phase surface engineering, using the proprietary Kolsterising(®) treatment from Bodycote Hardiff GmbH, that is currently being used mainly on stainless steel, with Co-Cr-Mo alloys, an improvement in hardness and tribological characteristics is predicted. The objective of this paper is to analyze the biocompatibility of a Kolsterised(®) Co-Cr-Mo alloy, and to characterize the material surface in order to show the advantages gained by using the Kolsterised(®) material relative to the original untreated alloy, and other materials. This work has been performed on 3 fronts including; Material characterization, "In-vitro" corrosion testing, and Biological testing conforming to BS EN ISO 10993-18:2009 - Biological evaluation of medical devices. Using these techniques, the Kolsterised(®) cobalt-chromium-molybdenum alloys were found to have good biocompatibility and an augmented corrosion resistance when compared with the untreated alloy. The Kolsterised(®) samples also showed a 150% increase in surface hardness over the untreated material thus predicting better wear properties.

Ablation from High Velocity Clouds: A Source for Low Velocity Ionized Gas

NASA Astrophysics Data System (ADS)

Shelton, Robin L.; Henley, D. B.; Kwak, K.

2012-05-01

High velocity clouds shed material as they move through the Galaxy. This material mixes with the Galactic interstellar medium, resulting in plasma whose temperature and ionization levels are intermediate between those of the cloud and those of the Galaxy. As time passes, the mixed material slows to the velocity of the ambient gas. This raises the possibility that initially warm (T 10^3 K), poorly ionized clouds moving through hot (T 10^6 K), very highly ionized ambient gas could lead to mixed gas that harbors significant numbers of high ions (O+5, N+4, and C+3) and thus helps to explain the large numbers of low-velocity high ions seen on high latitude lines of sight through the Galactic halo. We have used a series of detailed FLASH simulations in order to track the hydrodynamics of warm clouds embedded in hot Galactic halo gas. These simulations tracked the ablated material as it mixed and slowed to low velocities. By following the ionization levels of the gas in a time-dependent fashion, we determined that the mixed material is rich in O+5, N+4, and C+3 ions and continues to contain these ions for some time after slowing to low velocities. Combining our simulational results with estimates of the high velocity cloud infall rate leads to the finding that the mixed gas can account for 1/3 of the normal-velocity O+5 column density found on high latitude lines of sight. It accounts for lesser fractions of the N+4 and C+3 column densities. We will discuss our high velocity cloud results as part of a composite halo model that also includes cooling Galactic fountain gas, isolated supernova remnants, and ionizing photons.

Analysis of Critical Parts and Materials

DTIC Science & Technology

1980-12-01

1 1 1% 1% 1% 1% Large Orders Manual Ordering of Some Critical Parts Order Spares with Original Order Incentives Belter Capital Investment...demand 23 Large orders 24 Long lead procurement funding (including raw materials, facility funding) 25 Manpower analysis and training 26 Manual ... ordering of some critical parts 27 More active role in schedule negotiation 28 Multiple source procurements 29 Multi-year program funding 30 Order

Microstructural Design for Improving Ductility of An Initially Brittle Refractory High Entropy Alloy.

PubMed

Soni, V; Senkov, O N; Gwalani, B; Miracle, D B; Banerjee, R

2018-06-11

Typically, refractory high-entropy alloys (RHEAs), comprising a two-phase ordered B2 + BCC microstructure, exhibit extraordinarily high yield strengths, but poor ductility at room temperature, limiting their engineering application. The poor ductility is attributed to the continuous matrix being the ordered B2 phase in these alloys. This paper presents a novel approach to microstructural engineering of RHEAs to form an "inverted" BCC + B2 microstructure with discrete B2 precipitates dispersed within a continuous BCC matrix, resulting in improved room temperature compressive ductility, while maintaining high yield strength at both room and elevated temperature.

Reminder cards and immunization rates among Latinos and the rural poor in Northeast Colorado.

PubMed

Hicks, Paul; Tarr, Gillian A M; Hicks, Ximena Prieto

2007-01-01

Immunization rates are static in the United States. Risk factors for not being up to date (UTD) include ethnicity and lower socioeconomic status. Reminder cards increase immunization rates in urban settings. Their effect in poor, Latino, and rural children is unknown. Language-appropriate reminder cards were sent to active patients not UTD listing the vaccines missing; the card served as the physician order for the vaccine. Missed opportunities were addressed through discussion with staff and posters in patient care rooms. UTD rates before and after intervention were measured. Dual-purpose reminder/order cards increased the rate of UTD from 61.3% to 73.4%; children living near the clinic, patients who speak only Spanish, and Latinos overall showed preferential effectiveness. Children eligible to participate in the Vaccines for Children program had similar increases in UTD rates but had lower baseline and final UTD rates than did children not eligible for the Vaccines for Children program. The rate of missed opportunities did not change. The number of children to whom reminder cards needed to be sent for them to become fully immunized is 8 (number needed to treat). In poor, rural, and Latino populations, language-appropriate reminder/order cards increase immunization rates.

Adenovirus (For Parents)

MedlinePlus

... through respiratory secretions (coughs or sneezes) or fecal contamination. Fecal material can spread via contaminated water, eating food contaminated by houseflies, and poor hand washing (such ...

High internal free volume compositions for low-k dielectric and other applications

NASA Technical Reports Server (NTRS)

Bouffard, Jean (Inventor); Swager, Timothy M. (Inventor)

2010-01-01

The present invention provides materials, devices, and methods involving new heterocyclic, shape-persistent monomeric units with internal free volume. In some cases, materials the present invention may comprise monomers, oligomers, or polymers that incorporate a heterocyclic, shape-persistent iptycene. The present invention may provide materials having low dielectric constants and improved stability at high operating temperatures due to the electron-poor character of materials. In addition, compositions of the invention may be easily synthesized and readily modified to suit a particular application.

Trends in financial satisfaction: does poverty make a difference?

PubMed

Hsieh, Chang-Ming

2002-01-01

Gerontological studies on financial satisfaction have been limited by the dearth of longitudinal research and the lack of research that includes the concept of poverty. In order to bridge these gaps, this longitudinal study examines and compares the intracohort and intercohort effects on financial satisfaction trends by poverty status among Americans age 45 and above, using data from the General Social Surveys. The results suggest that for both the poor and the non-poor, changes in financial satisfaction trends are mostly due to strong negative intercohort effects, indicating that younger cohorts are less satisfied financially than the older ones. There appears to be a significant difference in the intercohort effects of financial satisfaction trends between the poor and the non-poor. However, such difference can be accounted for by the differences in the effects of education and social comparison (or relative deprivation) on financial satisfaction between the poor and the non-poor.

A review of catalyst-enhanced magnesium hydride as a hydrogen storage material

NASA Astrophysics Data System (ADS)

Webb, C. J.

2015-09-01

Magnesium hydride remains an attractive hydrogen storage material due to the high hydrogen capacity and low cost of production. A high activation energy and poor kinetics at practical temperatures for the pure material have driven research into different additives to improve the sorption properties. This review details the development of catalytic additives and their effect on the activation energy, kinetics and thermodynamic properties of magnesium hydride.

Containerless Liquid-Phase Processing of Ceramic Materials

NASA Technical Reports Server (NTRS)

Weber, J. K. Richard (Principal Investigator); Nordine, Paul C.

1996-01-01

The present project builds on the results of research supported under a previous NASA grant to investigate containerless liquid-phase processing of molten ceramic materials. The research used an aero-acoustic levitator in combination with cw CO2 laser beam heating to achieve containerless melting, superheating, undercooling, and solidification of poorly-conducting solids and liquids. Experiments were performed on aluminum oxide, binary aluminum oxide-silicon dioxide materials, and oxide superconductors.

Comparative color and surface parameters of current esthetic restorative CAD/CAM materials

PubMed Central

2018-01-01

PURPOSE The purpose of this study was to derive and compare the inherent color (hue angle, chroma), translucency (TPSCI), surface gloss (ΔE*SCE-SCI), and surface roughness (Ra) amongst selected shades and brands of three hybrid CAD/CAM blocks [GC Cerasmart (CS); Lava Ultimate (LU); Vita Enamic (VE)]. MATERIALS AND METHODS The specimens (N = 225) were prepared into square-shaped (12 × 12 mm2) with different thicknesses and shades. The measurements of color, translucency, and surface gloss were performed by a reflection spectrophotometer. The surface roughness and surface topography were assessed by white light interferometry. RESULTS Results revealed that hue and chroma values were influenced by the material type, material shade, and material thickness (P < .001). The order of hue angle amongst the materials was LU > CS > VE, whereas the order of chroma was VE > CS > LU. TPSCI results demonstrated a significant difference in terms of material types and material thicknesses (P ≤ .001). TPSCI values of the tested materials were ordered as LU > CS > VE. ΔE*SCE-SCI and Ra results were significantly varied amongst the materials (P < .001) and amongst the shades (P < .05). The order of ΔE*SCE-SCI amongst the materials were as follows LU > VE ≥ CS, whereas the order of Ra was CS ≥ VE > LU. CONCLUSION Nano-ceramic and polymer-infiltrated-feldspathic ceramic-network CAD/CAM materials exhibited different optical, inherent color and surface parameters. PMID:29503712

Systematic Optimization of Battery Materials: Key Parameter Optimization for the Scalable Synthesis of Uniform, High-Energy, and High Stability LiNi0.6Mn0.2Co0.2O2 Cathode Material for Lithium-Ion Batteries.

PubMed

Ren, Dong; Shen, Yun; Yang, Yao; Shen, Luxi; Levin, Barnaby D A; Yu, Yingchao; Muller, David A; Abruña, Héctor D

2017-10-18

Ni-rich LiNi x Mn y Co 1-x-y O 2 (x > 0.5) (NMC) materials have attracted a great deal of interest as promising cathode candidates for Li-ion batteries due to their low cost and high energy density. However, several issues, including sensitivity to moisture, difficulty in reproducibly preparing well-controlled morphology particles and, poor cyclability, have hindered their large scale deployment; especially for electric vehicle (EV) applications. In this work, we have developed a uniform, highly stable, high-energy density, Ni-rich LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode material by systematically optimizing synthesis parameters, including pH, stirring rate, and calcination temperature. The particles exhibit a spherical morphology and uniform size distribution, with a well-defined structure and homogeneous transition-metal distribution, owing to the well-controlled synthesis parameters. The material exhibited superior electrochemical properties, when compared to a commercial sample, with an initial discharge capacity of 205 mAh/g at 0.1 C. It also exhibited a remarkable rate capability with discharge capacities of 157 mAh/g and 137 mAh/g at 10 and 20 C, respectively, as well as high tolerance to air and moisture. In order to demonstrate incorporation into a commercial scale EV, a large-scale 4.7 Ah LiNi 0.6 Mn 0.2 Co 0.2 O 2 Al-full pouch cell with a high cathode loading of 21.6 mg/cm 2 , paired with a graphite anode, was fabricated. It exhibited exceptional cyclability with a capacity retention of 96% after 500 cycles at room temperature. This material, which was obtained by a fully optimized scalable synthesis, delivered combined performance metrics that are among the best for NMC materials reported to date.

History of Nebular Processing Traced by Silicate Stardust in IDPS

NASA Technical Reports Server (NTRS)

Messenger, Scott R.; Keller, L. P.; Nakamura-Messenger, K.

2010-01-01

Chondritic porous interplanetary dust particles (CP-IDPs) may be the best preserved remnants of primordial solar system materials, in part because they were not affected by parent body hydrothermal alteration. Their primitive characteristics include fine grained, unequilibrated, anhydrous mineralogy, enrichment in volatile elements, and abundant molecular cloud material and silicate stardust. However, while the majority of CP-IDP materials likely derived from the Solar System, their formation processes and provenance are poorly constrained. Stardust abundances provide a relative measure of the extent of processing that the Solar System starting materials has undergone in primitive materials. For example, among primitive meteorites silicate stardust abundances vary by over two orders of magnitude (less than 10-200 ppm). This range of abundances is ascribed to varying extents of aqueous processing in the meteorite parent bodies. The higher average silicate stardust abundances among CP-IDPs (greater than 375 ppm) are thus attributable to the lack of aqueous processing of these materials. Yet, silicate stardust abundances in IDPs also vary considerably. While the silicate stardust abundance in IDPs having anomalous N isotopic compositions was reported to be 375 ppm, the abundance in IDPs lacking N anomalies is less than 10 ppm. Furthermore, these values are significantly eclipsed among some IDPs with abundances ranging from 2,000 ppm to 10,000 ppm. Given that CP-IDPs have not been significantly affected by parent body processes, the difference in silicate stardust abundances among these IDPs must reflect varying extents of nebular processing. Here we present recent results of a systematic coordinated mineralogical/isotopic study of large cluster IDPs aimed at (1) characterizing the mineralogy of presolar silicates and (2) delineating the mineralogical and petrographic characteristics of IDPs with differing silicate stardust abundances. One of the goals of this study is to better understand the earliest stages of evolution of the Solar System starting materials.

Gender and the Social Order in Early Modern England.

ERIC Educational Resources Information Center

Amussen, Susan Dwyer

The place of the family and the relationship between gender and social order in England between 1560 and 1725 are examined. The fear of disorder so prevalent in England in the late 16th and early 17th centuries was caused by the doubling of the population and extremely poor economic conditions. In the attempt to enforce order, the analogy between…

Computed tomographic assessment of the causal factors of unsuccessful medialization thyroplasty.

PubMed

Iwahashi, Toshihiko; Ogawa, Makoto; Hosokawa, Kiyohito; Mochizuki, Ryuichi; Inohara, Hidenori

2015-03-01

The present results demonstrate that a small implant size, undercorrection of the vocal fold, antero-posterior implant malposition, and the use of expanded polytetrafluoroethylene (ePTFE) are the primary factors that cause a poor outcome of medialization thyroplasty (MT). To assess the postoperative laryngeal condition using computed tomography (CT) in patients with unilateral vocal fold paralysis who underwent MT alone, and to identify the primary causal factors in terms of the surgical procedures that affect the outcomes of MT. Twenty-two patients who underwent MT alone were divided into two groups based on either the maximal phonation time or the perceived vocal breathiness. Two laryngologists assessed the postoperative laryngeal CT images during sustained vowel phonation and judged whether there were abnormalities of the arytenoid cartilage position, window position, implant size, and implant position, as well as the degree of correction of the vocal fold. As implant material, a silicone block, ePTFE, and hydroxyapatite had been inserted in 2, 9, and 11 patients, respectively. Comparisons of the prevalence of abnormalities in the abovementioned factors between the different outcomes and between the types of material used for the implant were performed. Twelve patients with a poor outcome and 10 with a good outcome showed 36 and 18 abnormal findings identified by either of the two laryngologists, respectively. In the poor outcome group, a smaller implant size and undercorrection of the vocal fold showed both high kappa values and a significantly higher prevalence than those in the good outcome group (p < 0.001 and p < 0.05), respectively. The comparison between material types demonstrated that the sheet-like material (ePTFE) group exhibited a significantly higher prevalence of undercorrection than the block-like material group (p < 0.05).

49 CFR 109.17 - Emergency Orders.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS AND OIL TRANSPORTATION DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS PROCEDURAL REGULATIONS FOR OPENING OF PACKAGES, EMERGENCY ORDERS, AND...

49 CFR 109.17 - Emergency Orders.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS AND OIL TRANSPORTATION DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS PROCEDURAL REGULATIONS FOR OPENING OF PACKAGES, EMERGENCY ORDERS, AND...

49 CFR 109.17 - Emergency Orders.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS AND OIL TRANSPORTATION DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS PROCEDURAL REGULATIONS FOR OPENING OF PACKAGES, EMERGENCY ORDERS, AND...

The development and characterization of degradable poly(vinyl ester) and poly(vinyl ester)/PEO block copolymers

NASA Astrophysics Data System (ADS)

Lipscomb, Corinne Elizabeth

The development of biodegradable materials is a challenging and important problem in polymer science. A review of the state of the art in degradable materials is presented, which reveals that current biodegradable materials do not exhibit the thermal or mechanical properties necessary for widespread applications. One strategy for toughening polymeric materials, which has previously been applied to non-degradable thermoplastics and thermoplastic elastomers, is the formation of block copolymers. Poly(vinyl esters) (PVE) homopolymers are known to have a wide range of properties, but PVE block copolymers comprise a class of inexpensive and (bio)degradable materials that were previously unknown. Therefore, the synthesis and properties of these block copolymers were explored in an effort to develop robust degradable materials. This thesis research probes the reaction conditions necessary for the reversible-addition fragmentation chain transfer (RAFT) polymerization and chain extension reactions of vinyl ester monomers. PVE di- and triblock copolymers are synthesized and studied, and the triblock copolymers display extremely poor toughness due to their relatively low molecular weights in light of the high entanglement molecular weight of the poly(vinyl acetate) center block. Attempts to improve the mechanical properties of these materials focus on the incorporation of poly(ethylene oxide) (PEO) as a low entanglement molecular weight and biocompatible center block in PVE-containing triblock copolymers. Depending on the choice of PVE endblocks and the overall polymer composition, crystallization of the PEO block can be controlled, confined, or inhibited. Polymers in which PEO crystallization is completely inhibited exhibit enhanced mechanical properties and behave as weak thermoplastics. In order to understand the relationship between the inhibition of PEO crystallization and the mechanical properties of PVE/PEO materials, these polymers were studied using dynamic mechanical spectroscopy, wide angle X-ray scattering, small angle X-ray scattering, differential scanning calorimetry, and uniaxial tensile tests. By combining insights gained from these techniques, a complex picture emerges that explains the enhanced mechanical properties of these materials based on the type and location of thermal transitions, amorphous PEO entanglements, and the strain-induced crystallization of PEO. This work represents an important step toward developing robust materials with tunable properties containing (bio)degradable components.

Spatially resolved surface valence gradient and structural transformation of lithium transition metal oxides in lithium-ion batteries.

PubMed

Liu, Hanshuo; Bugnet, Matthieu; Tessaro, Matteo Z; Harris, Kristopher J; Dunham, Mark J R; Jiang, Meng; Goward, Gillian R; Botton, Gianluigi A

2016-10-26

Layered lithium transition metal oxides are one of the most important types of cathode materials in lithium-ion batteries (LIBs) that possess high capacity and relatively low cost. Nevertheless, these layered cathode materials suffer structural changes during electrochemical cycling that could adversely affect the battery performance. Clear explanations of the cathode degradation process and its initiation, however, are still under debate and not yet fully understood. We herein systematically investigate the chemical evolution and structural transformation of the LiNi x Mn y Co 1-x-y O 2 (NMC) cathode material in order to understand the battery performance deterioration driven by the cathode degradation upon cycling. Using high-resolution electron energy loss spectroscopy (HR-EELS) we clarify the role of transition metals in the charge compensation mechanism, particularly the controversial Ni 2+ (active) and Co 3+ (stable) ions, at different states-of-charge (SOC) under 4.6 V operation voltage. The cathode evolution is studied in detail from the first-charge to long-term cycling using complementary diagnostic tools. With the bulk sensitive 7 Li nuclear magnetic resonance (NMR) measurements, we show that the local ordering of transition metal and Li layers (R3[combining macron]m structure) is well retained in the bulk material upon cycling. In complement to the bulk measurements, we locally probe the valence state distribution of cations and the surface structure of NMC particles using EELS and scanning transmission electron microscopy (STEM). The results reveal that the surface evolution of NMC is initiated in the first-charging step with a surface reduction layer formed at the particle surface. The NMC surface undergoes phase transformation from the layered structure to a poor electronic and ionic conducting transition-metal oxide rock-salt phase (R3[combining macron]m → Fm3[combining macron]m), accompanied by irreversible lithium and oxygen loss. In addition to the electrochemical cycling effect, electrolyte exposure also shows non-negligible influence on cathode surface degradation. These chemical and structural changes of the NMC cathode could contribute to the first-cycle coulombic inefficiency, restrict the charge transfer characteristics and ultimately impact the cell capacity.

Development and Characterization of SiC)/ MoSi2-Si3N4(p) Hybrid Composites

NASA Technical Reports Server (NTRS)

Hebsur, Mohan G.

1998-01-01

Intermetallic compound MoSi2 has long been known as a high temperature material that has excellent oxidation resistance and electrical/thermal conductivity. Also its low cost, high melting point (2023 C), relatively low density (6.2 g/cu cm versus 9 g/cu cm for current engine materials), and ease of machining, make it an attractive structural material. However, the use of MoSi2 has been hindered due to its poor toughness at low temperatures, poor creep resistance at high temperatures, and accelerated oxidation (also known as 'pest' oxidation) at temperatures between approximately 450 and 550 C. Continuous fiber reinforcing is very effective means of improving both toughness and strength. Unfortunately, MoSi2 has a relatively high coefficient of thermal expansion (CTE) compared to potential reinforcing fibers such as SiC. The large CTE mismatch between the fiber and the matrix resulted in severe matrix cracking during thermal cycling. Addition of about 30 to 50 vol % of Si3N4 particulate to MoSi2 improved resistance to low temperature accelerated oxidation by forming a Si2ON2 protective scale and thereby eliminating catastrophic 'pest failure'. The Si3N4 addition also improved the high temperature creep strength by nearly five orders of magnitude, doubled the room temperature toughness and significantly lowered the CTE of the MoSi2 and eliminated matrix cracking in SCS-6 reinforced composites even after thermal cycling. The SCS-6 fiber reinforcement improved the room temperature fracture toughness by seven times and impact resistance by five times. The composite exhibited excellent strength and toughness improvement up to 1400 C. More recently, tape casting was adopted as the preferred processing of MoSi2-base composites for improved fiber spacing, ability to use small diameter fibers, and for lower cost. Good strength and toughness values were also obtained with fine diameter Hi-Nicalon tow fibers. This hybrid composite remains competitive with ceramic matrix composites as a replacement for Ni-base superalloys in aircraft engine applications.

Utilitarian models of the solar nebula

NASA Technical Reports Server (NTRS)

Cassen, Patrick

1994-01-01

Models of the primitive solar nebula based on a combination of theory, observations of T Tauri stars, and global conservation laws are presented. The models describe the motions of nebular gas, mixing of interstellar material during the formation of the nebula, and evolution of thermal structure in terms of several characteristic parameters. The parameters describe key aspects of the protosolar cloud (its rotation rate and collapse rate) and the nebula (its mass relative to the Sun, decay time, and density distribution). For most applications, the models are heuristic rather than predicted. Their purpose is to provide a realistic context for the interpretation of solar system data, and to distinquish those nebular characteristics that can be specified with confidence, independently of the assumtions of particular models, form those that are poorly constrained. It is demonstrated that nebular gas typically experienced large radial excursions during the evolution of the nebula and that both inward and outward mean radial velocities on the order of meters per second occured in the terrestrial planet region, with inward velocities predominant for most ofthe evolution. However, the time history of disk size, surface density, and radial velocities are sensitive to the total angular momentun of the protosolar cloud, which cannot be constrained by purely theoretical considerations.It is shown that a certain amount of 'formational' mixing of interstellar material was an inevitable consequenc of nebular mass and angular momentum transport during protostellar collapse, regardless of the specific transport mechanisms invloved. Even if the protosolar cloud was initially homogeneous, this mixing was important because it had the effect of mingling presolar material that had experienced different degrees of thermal processing during collapse and passage through the accertion shock. Nebular thermal structure is less sensitive to poorly constrained parameters than is dynamical history. A simple criterion is derived for the condition that silicate grains are evaporated at midplane, and it is argued that this condition was probably fulfilled early in nebular history. Cooling of a hot nebula due tocoagulation of dust and consequent local reduction of optical depth is examined, and it is shown how such a process leads naturally to an enrichment of rock-forming elements in the gas phase.

"Plastic" solar cells: self-assembly of bulk heterojunction nanomaterials by spontaneous phase separation.

PubMed

Peet, Jeffrey; Heeger, Alan J; Bazan, Guillermo C

2009-11-17

As the global demand for low-cost renewable energy sources intensifies, interest in new routes for converting solar energy to electricity is rapidly increasing. Although photovoltaic cells have been commercially available for more than 50 years, only 0.1% of the total electricity generated in the United States comes directly from sunlight. The earliest commercial solar technology remains the basis for the most prevalent devices in current use, namely, highly-ordered crystalline, inorganic solar cells, commonly referred to as silicon cells. Another class of solar cells that has recently inspired significant academic and industrial excitement is the bulk heterojunction (BHJ) "plastic" solar cell. Research by a rapidly growing community of scientists across the globe is generating a steady stream of new insights into the fundamental physics, the materials design and synthesis, the film processing and morphology, and the device science and architecture of BHJ technology. Future progress in the fabrication of high-performance BHJ cells will depend on our ability to combine aspects of synthetic and physical chemistry, condensed matter physics, and materials science. In this Account, we use a combination of characterization tools to tie together recent advances in BHJ morphology characterization, device photophysics, and thin-film solution processing, illustrating how to identify the limiting factors in solar cell performance. We also highlight how new processing methods, which control both the BHJ phase separation and the internal order of the components, can be implemented to increase the power conversion efficiency (PCE). The failure of many innovative materials to achieve high performance in BHJ solar cell devices has been blamed on "poor morphology" without significant characterization of either the structure of the phase-separated morphology or the nature of the charge carrier recombination. We demonstrate how properly controlling the "nanomorphology", which is critically dependent on minute experimental details at every step, from synthesis to device construction, provides a clear path to >10% PCE BHJ cells, which can be fabricated at a fraction of the cost of conventional solar cells.

Distance Learners' Perspective on User-Friendly Instructional Materials at the University of Zambia

ERIC Educational Resources Information Center

Simui, F.; Thompson, L. C.; Mundende, K.; Mwewa, G.; Kakana, F.; Chishiba, A.; Namangala, B.

2017-01-01

This case study focuses on print-based instructional materials available to distance education learners at the University of Zambia. Using the Visual Paradigm Software, we model distance education learners' voices into sociograms to make a contribution to the ongoing discourse on quality distance learning in poorly resourced communities. Emerging…

"I Want to Help Girls Like Me": An Exploration of the Educational Aspirations of Teenage Girls in Kolkata Slums

ERIC Educational Resources Information Center

Ipe, Rebecca

2016-01-01

This qualitative study used participatory visual research in order to develop an understanding of the educational experiences of urban poor adolescent girls in Kolkata and to elicit their capabilities. The sample comprised urban poor girls who were undergoing formal education at a religious, philanthropic primary school in Kolkata. Findings from…

Comparative color and surface parameters of current esthetic restorative CAD/CAM materials.

PubMed

Egilmez, Ferhan; Ergun, Gulfem; Cekic-Nagas, Isil; Vallittu, Pekka Kalevi; Lassila, Lippo Veli Juhana

2018-02-01

The purpose of this study was to derive and compare the inherent color (hue angle, chroma), translucency (TP SCI ), surface gloss (ΔE * SCE-SCI ), and surface roughness (R a ) amongst selected shades and brands of three hybrid CAD/CAM blocks [GC Cerasmart (CS); Lava Ultimate (LU); Vita Enamic (VE)]. The specimens (N = 225) were prepared into square-shaped (12 × 12 mm 2 ) with different thicknesses and shades. The measurements of color, translucency, and surface gloss were performed by a reflection spectrophotometer. The surface roughness and surface topography were assessed by white light interferometry. Results revealed that hue and chroma values were influenced by the material type, material shade, and material thickness ( P < .001). The order of hue angle amongst the materials was LU > CS > VE, whereas the order of chroma was VE > CS > LU. TP SCI results demonstrated a significant difference in terms of material types and material thicknesses ( P ≤ .001). TP SCI values of the tested materials were ordered as LU > CS > VE. ΔE * SCE-SCI and R a results were significantly varied amongst the materials ( P < .001) and amongst the shades ( P < .05). The order of ΔE * SCE-SCI amongst the materials were as follows LU > VE ≥ CS, whereas the order of R a was CS ≥ VE > LU. Nano-ceramic and polymer-infiltrated-feldspathic ceramic-network CAD/CAM materials exhibited different optical, inherent color and surface parameters.

How much more exposed are the poor to natural disasters? Global and regional measurement.

PubMed

Kim, Namsuk

2012-04-01

This paper proposes a simple indicator to measure the exposure to natural disasters for the poor and non-poor population, in order to assess the global and regional trend of natural hazard and poverty. Globally, poor people are two times more exposed to natural disasters than the non-poor in the twenty-first century. The time trend varies across regions, with poor people in East Asia and Pacific being most exposed to natural disasters, followed by those in South Asia and Sub-Saharan Africa. The change of exposure measure over time is decomposed into two factors: a pure exposure change, which could be fuelled by climate change; and a concentration component. The result shows that the total net increase of exposure between the 1970s and the 2000s is driven significantly by the increased concentration of the poor (26 per cent) in disaster-prone areas, whereas the contribution of that factor remains very small for the non-poor (six per cent). © 2012 The Author(s). Disasters © Overseas Development Institute, 2012.

Are faults preferential flow paths through semiarid and arid vadose zones?

NASA Astrophysics Data System (ADS)

Sigda, John M.; Wilson, John L.

2003-08-01

Numerous faults crosscut the poorly lithified, basin-fill sands found in New Mexico's Rio Grande rift and in other extensional regimes. The deformational processes that created these faults sharply reduced both fault porosity and fault saturated hydraulic conductivity by altering grains and pores, particularly in structures referred to as deformation bands. The resulting pore distribution changes, which create barriers to saturated flow, should enhance fault unsaturated flow relative to parent sand under the relatively dry conditions of the semiarid southwest. We report the first measurements of unsaturated hydraulic properties for undisturbed fault materials, using samples from a small-displacement normal fault and parent sands in the Bosque del Apache Wildlife Refuge, central New Mexico. Fault samples were taken from a narrow zone of deformation bands. The unsaturated flow apparatus (UFA) centrifuge system was used to measure both relative permeability and moisture retention curves. We compared these relations and fitted hydraulic conductivity-matric potential models to test whether the fault has significantly different unsaturated hydraulic properties than its parent sand. Saturated conductivity is 3 orders of magnitude less in the fault than the undeformed sand. As matric potential decreases from 0 to -200 cm, unsaturated conductivity decreases roughly 1 order of magnitude in the fault but 5-6 orders of magnitude in undeformed sands. Fault conductivity is greater by 2-6 orders of magnitude at matric potentials between -200 and -1000 cm, which are typical potentials for semiarid and arid vadose zones. Fault deformation bands have much higher air-entry matric potential values than parent sands and remain close to saturation well after the parent sands have begun to approach residual moisture content. Under steady state, one-dimensional, gravity-driven flow conditions, moisture transport and solute advection is 102-106 times larger in the fault material than parent sands. Faults are sufficiently conductive to hasten the downward movement of water and solutes through vadose-zone sands under semiarid and arid conditions like those in the Rio Grande rift, thereby potentially enhancing recharge, contaminant migration, and diagenesis.

49 CFR 174.106 - “Order-Notify” or “C.O.D.” shipments, Division 1.1 or 1.2 (explosive) materials.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false âOrder-Notifyâ or âC.O.D.â shipments, Division 1.1... MATERIALS REGULATIONS CARRIAGE BY RAIL Class I (Explosive) Materials § 174.106 “Order-Notify” or “C.O.D... to “order-notify” or “C.O.D.”, except on a through bill of lading to a place outside the United...

Self-assembly of water-soluble nanocrystals

DOEpatents

Fan, Hongyou [Albuquerque, NM; Brinker, C Jeffrey [Albuquerque, NM; Lopez, Gabriel P [Albuquerque, NM

2012-01-10

A method for forming an ordered array of nanocrystals where a hydrophobic precursor solution with a hydrophobic core material in an organic solvent is added to a solution of a surfactant in water, followed by removal of a least a portion of the organic solvent to form a micellar solution of nanocrystals. A precursor co-assembling material, generally water-soluble, that can co-assemble with individual micelles formed in the micellar solution of nanocrystals can be added to this micellar solution under specified reaction conditions (for example, pH conditions) to form an ordered-array mesophase material. For example, basic conditions are used to precipitate an ordered nanocrystal/silica array material in bulk form and acidic conditions are used to form an ordered nanocrystal/silica array material as a thin film.

Analysis of Air Force Wartime Contracted Construction Project Performance

DTIC Science & Technology

2015-03-26

Management, Volume 140. Branconi, C. v. & Loch, C. H., 2004. Contracting for major projects: eight business levers for top management. International ...Problems X Material Supply Problems X Poor Owner Management X X Poor Contractor Management X Corruption and Bribery X The USACE survey...Kremers, et al., 2010; GAO, 2014; Thibault, 2011). The final difference, corruption and bribery , was mentioned in the USACE study as well as by Kremers

Elastomeric binders for electrodes. [in secondary lithium cells

NASA Technical Reports Server (NTRS)

Yen, S. P. S.; Shen, D. H.; Somoano, R. B.

1983-01-01

The poor mechanical integrity of the cathode represents an important problem which affects the performance of ambient temperature secondary lithium cells. Repeated charge of a TiS2 cathode may give rise to stresses which disturb the electrode structure and can contribute to capacity loss. An investigation indicates that the use of an inelastic binder material, such as Teflon, aggravates the problem, and can lead to electrode disruption and poor TiS2 particle-particle contact. The feasibility of a use of elastomers as TiS2 binder materials has, therefore, been explored. It was found that elastomeric binders provide an effective approach for simplifying rechargeable cathode fabrication. A pronounced improvement in the mechanical integrity of the cathode structure contributes to a prolonged cycle life.

Measurement of W + bb and a search for MSSM Higgs bosons with the CMS detector at the LHC

NASA Astrophysics Data System (ADS)

O'Connor, Alexander Pinpin

Tooling used to cure composite laminates in the aerospace and automotive industries must provide a dimensionally stable geometry throughout the thermal cycle applied during the part curing process. This requires that the Coefficient of Thermal Expansion (CTE) of the tooling materials match that of the composite being cured. The traditional tooling material for production applications is a nickel alloy. Poor machinability and high material costs increase the expense of metallic tooling made from nickel alloys such as 'Invar 36' or 'Invar 42'. Currently, metallic tooling is unable to meet the needs of applications requiring rapid affordable tooling solutions. In applications where the tooling is not required to have the durability provided by metals, such as for small area repair, an opportunity exists for non-metallic tooling materials like graphite, carbon foams, composites, or ceramics and machinable glasses. Nevertheless, efficient machining of brittle, non-metallic materials is challenging due to low ductility, porosity, and high hardness. The machining of a layup tool comprises a large portion of the final cost. Achieving maximum process economy requires optimization of the machining process in the given tooling material. Therefore, machinability of the tooling material is a critical aspect of the overall cost of the tool. In this work, three commercially available, brittle/porous, non-metallic candidate tooling materials were selected, namely: (AAC) Autoclaved Aerated Concrete, CB1100 ceramic block and Cfoam carbon foam. Machining tests were conducted in order to evaluate the machinability of these materials using end milling. Chip formation, cutting forces, cutting tool wear, machining induced damage, surface quality and surface integrity were investigated using High Speed Steel (HSS), carbide, diamond abrasive and Polycrystalline Diamond (PCD) cutting tools. Cutting forces were found to be random in magnitude, which was a result of material porosity. The abrasive nature of Cfoam produced rapid tool wear when using HSS and PCD type cutting tools. However, tool wear was not significant in AAC or CB1100 regardless of the type of cutting edge. Machining induced damage was observed in the form of macro-scale chipping and fracture in combination with micro-scale cracking. Transverse rupture test results revealed significant reductions in residual strength and damage tolerance in CB1100. In contrast, AAC and Cfoam showed no correlation between machining induced damage and a reduction in surface integrity. Cutting forces in machining were modeled for all materials. Cutting force regression models were developed based on Design of Experiment and Analysis of Variance. A mechanistic cutting force model was proposed based upon conventional end milling force models and statistical distributions of material porosity. In order to validate the model, predicted cutting forces were compared to experimental results. Predicted cutting forces agreed well with experimental measurements. Furthermore, over the range of cutting conditions tested, the proposed model was shown to have comparable predictive accuracy to empirically produced regression models; greatly reducing the number of cutting tests required to simulate cutting forces. Further, this work demonstrates a key adaptation of metallic cutting force models to brittle porous material; a vital step in the research into the machining of these materials using end milling.

An Empirical Evaluation of Air Force Field Feeding with Recommendations for a New System

DTIC Science & Technology

1984-06-01

however, lack of temperature control results in generally poor quality. Cooking eggs to order is difficult, if not impossible; browning meats is...from or Short Order Menu Two Juices Two Entrees -Hot and Cold Cereal Two Potatoes or Substitutes Eggs to Order Two Vegetables *One Breakfast Meat Three...designed to meet the requirement. 6. The menu to be served must be considered. A complete breakfast with eggs to order including omelets requires specific

State of the Art Review: Poverty and the Developing Brain.

PubMed

Johnson, Sara B; Riis, Jenna L; Noble, Kimberly G

2016-04-01

In the United States, >40% of children are either poor or near-poor. As a group, children in poverty are more likely to experience worse health and more developmental delay, lower achievement, and more behavioral and emotional problems than their more advantaged peers; however, there is broad variability in outcomes among children exposed to similar conditions. Building on a robust literature from animal models showing that environmental deprivation or enrichment shapes the brain, there has been increasing interest in understanding how the experience of poverty may shape the brain in humans. In this review, we summarize research on the relationship between socioeconomic status and brain development, focusing on studies published in the last 5 years. Drawing on a conceptual framework informed by animal models, we highlight neural plasticity, epigenetics, material deprivation (eg, cognitive stimulation, nutrient deficiencies), stress (eg, negative parenting behaviors), and environmental toxins as factors that may shape the developing brain. We then summarize the existing evidence for the relationship between child poverty and brain structure and function, focusing on brain areas that support memory, emotion regulation, and higher-order cognitive functioning (ie, hippocampus, amygdala, prefrontal cortex) and regions that support language and literacy (ie, cortical areas of the left hemisphere). We then consider some limitations of the current literature and discuss the implications of neuroscience concepts and methods for interventions in the pediatric medical home. Copyright © 2016 by the American Academy of Pediatrics.

State of the Art Review: Poverty and the Developing Brain

PubMed Central

Riis, Jenna L.; Noble, Kimberly G.

2016-01-01

In the United States, >40% of children are either poor or near-poor. As a group, children in poverty are more likely to experience worse health and more developmental delay, lower achievement, and more behavioral and emotional problems than their more advantaged peers; however, there is broad variability in outcomes among children exposed to similar conditions. Building on a robust literature from animal models showing that environmental deprivation or enrichment shapes the brain, there has been increasing interest in understanding how the experience of poverty may shape the brain in humans. In this review, we summarize research on the relationship between socioeconomic status and brain development, focusing on studies published in the last 5 years. Drawing on a conceptual framework informed by animal models, we highlight neural plasticity, epigenetics, material deprivation (eg, cognitive stimulation, nutrient deficiencies), stress (eg, negative parenting behaviors), and environmental toxins as factors that may shape the developing brain. We then summarize the existing evidence for the relationship between child poverty and brain structure and function, focusing on brain areas that support memory, emotion regulation, and higher-order cognitive functioning (ie, hippocampus, amygdala, prefrontal cortex) and regions that support language and literacy (ie, cortical areas of the left hemisphere). We then consider some limitations of the current literature and discuss the implications of neuroscience concepts and methods for interventions in the pediatric medical home. PMID:26952506

Effect of compatibilizing agents on the interface and mechanical behaviour of polypropylene/hemp bast fiber biocomposites

NASA Astrophysics Data System (ADS)

Boruvka, M.; Lenfeld, P.; Brdlik, P.; Behalek, L.

2015-07-01

During the last years automotive industry has given a lot of attention to the biobased polymers that are sustainable and eco-friendly. Nevertheless fully green composites are currently too expensive for most applications. A viable solution and logical starting point at this material revolution lies in reinforced synthetic thermoplastics based on plant derived biodegradable fibers. Plant fibers (PF's) have potential to reduce weight of composite vehicle parts up to 40% compared with the main automotive composites filler, glass fibers (GF's). Production of GF's composites is much more energy intensive and polluting compared with growing, harvesting and preparing of PF's. The main disadvantage of PF's lies in combination of non-polar hydrophobic polymer matrix and polar hydrophilic fibers. This combination creates poor interface with low adhesion of both components. That implies poor wettability of fibres by polymer matrix and low mechanical properties of biocomposites. Therefore specific compatibilizing agents (Struktol SA1012, Fusabond P353, Smart + Luperox) were used in order to enhance compatibility between reinforcement and matrix. In this paper sets of biocomposite compounds were prepared by twin screw extrusion considering different type and weight percentage (wt. %) of compatibilizing agents, hemp bast fibres (HBF's) within ratio 20 (wt. %) and polypropylene (PP) THERMOFIL PP E020M matrix. Resulting compounds were than injection molded and tested samples were characterized by means of scanning electron microscopy (SEM) and mechanical testing.

Nanoscale Morphology of PTB7 Based Organic Photovoltaics as a Function of Fullerene Size

DOE PAGES

Roehling, John D.; Baran, Derya; Sit, Joseph; ...

2016-08-08

High efficiency polymer:fullerene photovoltaic device layers self-assemble with hierarchical features from ångströms to 100’s of nanometers. The feature size, shape, composition, orientation, and order all contribute to device efficiency and are simultaneously difficult to study due to poor contrast between carbon based materials. This study seeks to increase device efficiency and simplify morphology measurements by replacing the typical fullerene acceptor with endohedral fullerene Lu 3N@PC 80BEH. The metal atoms give excellent scattering contrast for electron beam and x-ray experiments. Additionally, Lu 3N@PC 80BEH has a lower electron affinity than standard fullerenes, which can raise the open circuit voltage of photovoltaicmore » devices. Electron microscopy techniques are used to produce a detailed account of morphology evolution in mixtures of Lu 3N@PC 80BEH with the record breaking donor polymer, PTB7 and coated using solvent mixtures. We demonstrate that common solvent additives like 1,8-diiodooctane or chloronapthalene do not improve the morphology of endohedral fullerene devices as expected. The poor device performance is attributed to the lack of mutual miscibility between this particular polymer:fullerene combination and to co-crystallization of Lu 3N@PC 80BEH with 1,8-diiodooctane. This negative result explains why solvent additives mixtures are not necessarily a morphology cure-all.« less

The effects of whiteness on the health of whites in the USA.

PubMed

Malat, Jennifer; Mayorga-Gallo, Sarah; Williams, David R

2018-02-01

Whites in the USA are the dominant racial group, with greater than average access to most material and social rewards. Yet, while whites have better outcomes than other racial groups on some health indicators, whites paradoxically compare poorly on other measures. Further, whites in the USA also rank poorly in international health comparisons. In this paper, we present a framework that combines the concept of whiteness-a system that socially, economically, and ideologically benefits European descendants and disadvantages people in other groups-with research from a variety of fields in order to comprehensively model the social factors that influence whites' health. The framework we present describes how whiteness and capitalism in the USA shape societal conditions, individual social characteristics and experiences, and psychosocial responses to circumstances to influence health outcomes. We detail specific examples of how social policies supported by whiteness, the narratives of whiteness, and the privileges of whiteness may positively and negatively affect whites' health. In doing so, we suggest several areas for future research that can expand our understanding of how social factors affect health and can contribute to the patterns and paradoxes of whites' health. By expanding research to include theoretically-grounded analyses of the dominant group's health, we can achieve a more complete picture of how systems of racial inequity affect health. Copyright © 2017 Elsevier Ltd. All rights reserved.

Nanoscale Morphology of PTB7 Based Organic Photovoltaics as a Function of Fullerene Size

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roehling, John D.; Baran, Derya; Sit, Joseph

High efficiency polymer:fullerene photovoltaic device layers self-assemble with hierarchical features from ångströms to 100’s of nanometers. The feature size, shape, composition, orientation, and order all contribute to device efficiency and are simultaneously difficult to study due to poor contrast between carbon based materials. This study seeks to increase device efficiency and simplify morphology measurements by replacing the typical fullerene acceptor with endohedral fullerene Lu 3N@PC 80BEH. The metal atoms give excellent scattering contrast for electron beam and x-ray experiments. Additionally, Lu 3N@PC 80BEH has a lower electron affinity than standard fullerenes, which can raise the open circuit voltage of photovoltaicmore » devices. Electron microscopy techniques are used to produce a detailed account of morphology evolution in mixtures of Lu 3N@PC 80BEH with the record breaking donor polymer, PTB7 and coated using solvent mixtures. We demonstrate that common solvent additives like 1,8-diiodooctane or chloronapthalene do not improve the morphology of endohedral fullerene devices as expected. The poor device performance is attributed to the lack of mutual miscibility between this particular polymer:fullerene combination and to co-crystallization of Lu 3N@PC 80BEH with 1,8-diiodooctane. This negative result explains why solvent additives mixtures are not necessarily a morphology cure-all.« less

Understanding creep in sandstone reservoirs - theoretical deformation mechanism maps for pressure solution in granular materials

NASA Astrophysics Data System (ADS)

Hangx, Suzanne; Spiers, Christopher

2014-05-01

Subsurface exploitation of the Earth's natural resources removes the natural system from its chemical and physical equilibrium. As such, groundwater extraction and hydrocarbon production from subsurface reservoirs frequently causes surface subsidence and induces (micro)seismicity. These effects are not only a problem in onshore (e.g. Groningen, the Netherlands) and offshore hydrocarbon fields (e.g. Ekofisk, Norway), but also in urban areas with extensive groundwater pumping (e.g. Venice, Italy). It is known that fluid extraction inevitably leads to (poro)elastic compaction of reservoirs, hence subsidence and occasional fault reactivation, and causes significant technical, economic and ecological impact. However, such effects often exceed what is expected from purely elastic reservoir behaviour and may continue long after exploitation has ceased. This is most likely due to time-dependent compaction, or 'creep deformation', of such reservoirs, driven by the reduction in pore fluid pressure compared with the rock overburden. Given the societal and ecological impact of surface subsidence, as well as the current interest in developing geothermal energy and unconventional gas resources in densely populated areas, there is much need for obtaining better quantitative understanding of creep in sediments to improve the predictability of the impact of geo-energy and groundwater production. The key problem in developing a reliable, quantitative description of the creep behaviour of sediments, such as sands and sandstones, is that the operative deformation mechanisms are poorly known and poorly quantified. While grain-scale brittle fracturing plus intergranular sliding play an important role in the early stages of compaction, these time-independent, brittle-frictional processes give way to compaction creep on longer time-scales. Thermally-activated mass transfer processes, like pressure solution, can cause creep via dissolution of material at stressed grain contacts, grain-boundary diffusion and precipitation on pore walls. As a first step to better describe creep in sands and sandstones, we have derived a simple model for intergranular pressure solution (IPS) within an ordered pack of spherical grains, employing existing IPS rate models, such as those derived by Renard et al. (1999) and Spiers et al. (2004). This universal model is able to predict the conditions under which each of the respective pressure solution serial processes, i.e. diffusion, precipitation or dissolution, is dominant. In essence, this creates generic deformation mechanism maps for any granular material. We have used our model to predict the amount and rate of compaction for sandstone reservoirs, and compared our predictions to known subsidence rates for reservoirs around the world. This gives a first order-comparison to verify whether or not IPS is an important mechanism in controlling reservoir compaction.

Absorption characteristics of glass fiber materials at normal and oblique incidence. M.S. Thesis

NASA Technical Reports Server (NTRS)

Wyerman, B. R.

1974-01-01

The absorption characteristics of several fibrous materials of the Owens Corning 700 Fiberglas Series were measured to determine the variation in impedance as a function of incident angle of the sound wave. The results, indicate that the fibrous absorbents behave as extended reacting materials. The poor agreement between measurement and theory for sound absorption based on the parameters of flow resistance and porosity indicates that this theory does not adequately predict the acoustic behavior of fibrous materials. A much better agreement with measured results is obtained for values calculated from the bulk acoustic parameters of the material.

Impact compaction of a granular material

DOE PAGES

Fenton, Gregg; Asay, Blaine; Dalton, Devon

2015-05-19

The dynamic behavior of granular materials has importance to a variety of engineering applications. Structural seismic coupling, planetary science, and earth penetration mechanics, are just a few of the application areas. Although the mechanical behavior of granular materials of various types have been studied extensively for several decades, the dynamic behavior of such materials remains poorly understood. High-quality experimental data are needed to improve our general understanding of granular material compaction physics. This study will describe how an instrumented plunger impact system can be used to measure pressure-density relationships for model materials at high and controlled strain rates and subsequentlymore » used for computational modeling.« less

The effect of rare earth ions on structural, morphological and thermoelectric properties of nanostructured tin oxide based perovskite materials

NASA Astrophysics Data System (ADS)

Rajasekaran, P.; Alagar Nedunchezhian, A. S.; Yalini Devi, N.; Sidharth, D.; Arivanandhan, M.; Jayavel, R.

2017-11-01

Metal oxide based materials are promising for thermoelectric applications especially at elevated temperature due to their high thermal stability. Recently, perovskite based oxide materials have been focused as a novel thermoelectric material due to their tunable electrical conductivity. Thermoelectric properties of BaSnO3 has been extensively investigated. However, the effect of various rare earth doping on the thermoelectric properties of BaSnO3 is not studied in detail. In the present work, Ba1-x RE x SnO3 (RE  =  La and Sr) materials with x  =  0.05 were prepared by polymerization complex (PC) method in order to study the effect of RE incorporation on the structural, morphological and thermoelectric characteristics of BaSnO3. The structural and morphological properties of the synthesized materials were studied by XRD and TEM analysis. XRD analysis confirmed the mixed phases of the synthesized samples. The TEM images of Ba1-x Sr x SnO3 shows hexagonal and cubic morphology while, Ba1-x La x SnO3 exhibit rod like morphology. Various functional groups of the perovskite material were identified using FTIR analysis. Formation of the perovskite material was further confirmed by XPS analysis. The Seebeck coefficient of Ba0.95La0.05SnO3 was relatively higher than that of Ba0.95Sr0.05SnO3, especially at high temperature. The rod like morphology of Ba0.95La0.05SnO3 may facilitate fast electron transport which results high thermal power compared to Ba0.95Sr0.05SnO3 despite of its poor crystalline nature. The substitution of La3+ on the Ba2+ site could vary the carrier density which results high Seebeck coefficient of Ba0.95La0.05SnO3 compared to Ba0.95Sr0.05SnO3. From the experimental results, it is obvious that Ba0.95La0.05SnO3 could be a promising thermoelectric material for high temperature application.

Donor attention to reading materials.

PubMed

O'Brien, S F; Osmond, L; Choquet, K; Yi, Q-L; Goldman, M

2015-11-01

Mandatory predonation reading materials inform donors about risk factors for transmissible disease, possible complications of donation and changes to the donation process. We aimed to assess the attention to predonation reading materials and factors which may affect attention. A national survey in 2008 of 18,108 blood donors asked about self-assessed attention to reading the materials. In face-to-face interviews, 441 donors completed additional questions about reading the materials and a literacy test. Qualitative interviews of 27 donors assessed their approach to reading. In the national survey, most of the first-time donors said they read all or most of the materials (90.9% first-time vs. 57.6% repeat donors, P < 0.001) and 66% vs. 23.1% reported reading them carefully (P < 0.001). In face-to-face interviews comparing those who read materials carefully, skimmed or did not read, most knew that donors are informed of positive transmissible disease test results (97.1%, 95.5, 98.0 P > 0.05), but fewer recalled seeing the definition of sex (77.2%, 56.9, 24.2 P < 0.001). Literacy was poor (30.5% frustration level, 60.3% instructional, 9.2% independent) but similar when those who read materials carefully, skimmed or did not read were compared (P > 0.05). Qualitative interviews showed that donors are reluctant to read any more than necessary and decide based on perceived importance or relevance. Attention to predonation reading materials tends to be better among first-time donors. The effectiveness is limited by low motivation to read, especially for repeat donors, as well as poor literacy. © 2015 International Society of Blood Transfusion.

Microgravity Processing and Photonic Applications of Organic and Polymeric Materials

NASA Technical Reports Server (NTRS)

Frazier, Donald 0; Penn, Benjamin G.; Smith, David; Witherow, William K.; Paley, M. S.; Abdeldayem, Hossin A.

1998-01-01

In recent years, a great deal of interest has been directed toward the use of organic materials in the development of high-efficiency optoelectronic and photonic devices. There is a myriad of possibilities among organic which allow flexibility in the design of unique structures with a variety of functional groups. The use of nonlinear optical (NLO) organic materials such as thin-film waveguides allows full exploitation of their desirable qualities by permitting long interaction lengths and large susceptibilities allowing modest power input. There are several methods in use to prepare thin films, such as Langmuir-Blodgett (LB) and self-assembly techniques, vapor deposition, growth from sheared solution or melt, and melt growth between glass plates. Organics have many features that make Abstract: them desirable for use in optical devices such as high second- and third-order nonlinearities, flexibility of molecular design, and damage resistance to optical radiation. However, their use in devices has been hindered by processing difficulties for crystals and thin films. In this chapter, we discuss photonic and optoelectronic applications of a few organic materials and the potential role of microgravity on processing these materials. It is of interest to note how materials with second- and third-order nonlinear optical behavior may be improved in a diffusion-limited environment and ways in which convection may be detrimental to these materials. We focus our discussion on third-order materials for all-optical switching, and second-order materials for all-optical switching, and second-order materials for frequency conversion and electrooptics.

Non-integer viscoelastic constitutive law to model soft biological tissues to in-vivo indentation.

PubMed

Demirci, Nagehan; Tönük, Ergin

2014-01-01

During the last decades, derivatives and integrals of non-integer orders are being more commonly used for the description of constitutive behavior of various viscoelastic materials including soft biological tissues. Compared to integer order constitutive relations, non-integer order viscoelastic material models of soft biological tissues are capable of capturing a wider range of viscoelastic behavior obtained from experiments. Although integer order models may yield comparably accurate results, non-integer order material models have less number of parameters to be identified in addition to description of an intermediate material that can monotonically and continuously be adjusted in between an ideal elastic solid and an ideal viscous fluid. In this work, starting with some preliminaries on non-integer (fractional) calculus, the "spring-pot", (intermediate mechanical element between a solid and a fluid), non-integer order three element (Zener) solid model, finally a user-defined large strain non-integer order viscoelastic constitutive model was constructed to be used in finite element simulations. Using the constitutive equation developed, by utilizing inverse finite element method and in vivo indentation experiments, soft tissue material identification was performed. The results indicate that material coefficients obtained from relaxation experiments, when optimized with creep experimental data could simulate relaxation, creep and cyclic loading and unloading experiments accurately. Non-integer calculus viscoelastic constitutive models, having physical interpretation and modeling experimental data accurately is a good alternative to classical phenomenological viscoelastic constitutive equations.

Inattention, Hyperactivity and Low Parental Education in Children with Conduct Problems and Poor Reading Skills

ERIC Educational Resources Information Center

Kallitsoglou, Angeliki

2014-01-01

Concerns over the poor reading performance of children with conduct problems are often expressed by their parents and teachers. In order to intervene effectively with these children, it is necessary to know what their difficulties are, both at school and at home. To date, there is still a lot of ambiguity in relation to the specific difficulties…

Job Characteristics and Off-Job Activities as Predictors of Need for Recovery, Well-Being, and Fatigue

ERIC Educational Resources Information Center

Sonnentag, Sabine; Zijlstra, Fred R. H.

2006-01-01

Two empirical studies examined need for recovery (i.e., a person's desire to be temporarily relieved from demands in order to restore his or her resources) as a mediator in the relationship between poor job characteristics (high job demands, low job control) and high off-job demands, on the one hand, and fatigue and poor individual well-being, on…

Urban forest justice and the rights to wild foods, medicines, and materials in the city

Treesearch

Melissa R. Poe; Rebecca J. McClain; Marla Emery; Patrick Hurley

2013-01-01

Urban forests are multifunctional socio-ecological landscapes, yet some of their social benefits remain poorly understood. This paper draws on ethnographic evidence from Seattle, Washington to demonstrate that urban forests contain nontimber forest products that contribute a variety of wild foods, medicines, and materials for the wellbeing of urban residents. We show...

The Effect of Delayed-JOLs and Sentence Generation on Children's Monitoring Accuracy and Regulation of Idiom Study

ERIC Educational Resources Information Center

van Loon, Mariëtte H.; de Bruin, Anique B. H.; van Gog, Tamara; van Merriënboer, Jeroen J. G.

2013-01-01

When studying verbal materials, both adults and children are often poor at accurately monitoring their level of learning and regulating their subsequent restudy of materials, which leads to suboptimal test performance. The present experiment investigated how monitoring accuracy and regulation of study could be improved when learning idiomatic…

A Space Acquisition Leading Indicator Based on System Interoperation Maturity

DTIC Science & Technology

2010-12-01

delivered hardware, improper use of soldering materials, improper installation of thermal blankets , and missing test procedure documentation A poor...office, the first GEO integrated payload and spacecraft successfully completed thermal vacuum (TVAC) testing in November 2009. Program officials...contamination in delivered hardware, improper use of soldering materials, improper installation of thermal blankets , and missing test procedure

Transmission electron microscope analyses of alteration phases in martian meteorite MIL 090032

NASA Astrophysics Data System (ADS)

Hallis, L. J.; Ishii, H. A.; Bradley, J. P.; Taylor, G. J.

2014-06-01

The nakhlite group of martian meteorites found in the Antarctic contain varying abundances of both martian and terrestrial secondary alteration phases. The aim of this study was to use transmission electron microscopy (TEM) to compare martian and terrestrial alteration embodied within a single nakhlite martian meteorite find - MIL 090032. Martian alteration veins in MIL 090032 are composed of poorly ordered Fe-smectite phyllosilicate. This poorly-ordered smectite appears to be equivalent to the nanocrystalline phyllosilicate/hydrated amorphous gel phase previously described in the martian alteration veins of other nakhlites. Chemical differences in this nanocrystalline phyllosilicate between different nakhlites imply localised alteration, which occurred close to the martian surface in MIL 090032. Both structurally and compositionally the nakhlite nanocrystalline phyllosilicate shows similarities to the amorphous/poorly ordered phase recently discovered in martian soil by the Mars Curiosity Rover at Rocknest, Gale Crater. Terrestrially derived alteration phases in MIL 090032 include jarosite and gypsum, amorphous silicates, and Fe-oxides and hydroxides. Similarities between the mineralogy and chemistry of the MIL 090032 terrestrial and martian alteration phases suggest the alteration conditions on Mars were similar to those in the Antarctic. At both sites a small amount of fluid at low temperatures infiltrated the rock and became acidic as a result of the conversion of Fe2+ to Fe3+ under oxidising conditions.

Cognitive Skills and Street Activity.

ERIC Educational Resources Information Center

Foley, Matthew; McGuire, Donald

1981-01-01

Discusses trends in the descriptive literature about children and the poor. Presents anecdotal material of children's spontaneous street play and analyzes cognitive skills exhibited in these situations. (Author/GC)

DNA-programmable nanoparticle crystallization.

PubMed

Park, Sung Yong; Lytton-Jean, Abigail K R; Lee, Byeongdu; Weigand, Steven; Schatz, George C; Mirkin, Chad A

2008-01-31

It was first shown more than ten years ago that DNA oligonucleotides can be attached to gold nanoparticles rationally to direct the formation of larger assemblies. Since then, oligonucleotide-functionalized nanoparticles have been developed into powerful diagnostic tools for nucleic acids and proteins, and into intracellular probes and gene regulators. In contrast, the conceptually simple yet powerful idea that functionalized nanoparticles might serve as basic building blocks that can be rationally assembled through programmable base-pairing interactions into highly ordered macroscopic materials remains poorly developed. So far, the approach has mainly resulted in polymerization, with modest control over the placement of, the periodicity in, and the distance between particles within the assembled material. That is, most of the materials obtained thus far are best classified as amorphous polymers, although a few examples of colloidal crystal formation exist. Here, we demonstrate that DNA can be used to control the crystallization of nanoparticle-oligonucleotide conjugates to the extent that different DNA sequences guide the assembly of the same type of inorganic nanoparticle into different crystalline states. We show that the choice of DNA sequences attached to the nanoparticle building blocks, the DNA linking molecules and the absence or presence of a non-bonding single-base flexor can be adjusted so that gold nanoparticles assemble into micrometre-sized face-centred-cubic or body-centred-cubic crystal structures. Our findings thus clearly demonstrate that synthetically programmable colloidal crystallization is possible, and that a single-component system can be directed to form different structures.

Modifications in Glass Ionomer Cements: Nano-Sized Fillers and Bioactive Nanoceramics

PubMed Central

Najeeb, Shariq; Khurshid, Zohaib; Zafar, Muhammad Sohail; Khan, Abdul Samad; Zohaib, Sana; Martí, Juan Manuel Nuñez; Sauro, Salvatore; Matinlinna, Jukka Pekka; Rehman, Ihtesham Ur

2016-01-01

Glass ionomer cements (GICs) are being used for a wide range of applications in dentistry. In order to overcome the poor mechanical properties of glass ionomers, several modifications have been introduced to the conventional GICs. Nanotechnology involves the use of systems, modifications or materials the size of which is in the range of 1–100 nm. Nano-modification of conventional GICs and resin modified GICs (RMGICs) can be achieved by incorporation of nano-sized fillers to RMGICs, reducing the size of the glass particles, and introducing nano-sized bioceramics to the glass powder. Studies suggest that the commercially available nano-filled RMGIC does not hold any significant advantage over conventional RMGICs as far as the mechanical and bonding properties are concerned. Conversely, incorporation of nano-sized apatite crystals not only increases the mechanical properties of conventional GICs, but also can enhance fluoride release and bioactivity. By increasing the crystallinity of the set matrix, apatites can make the set cement chemically more stable, insoluble, and improve the bond strength with tooth structure. Increased fluoride release can also reduce and arrest secondary caries. However, due to a lack of long-term clinical studies, the use of nano-modified glass ionomers is still limited in daily clinical dentistry. In addition to the in vitro and in vivo studies, more randomized clinical trials are required to justify the use of these promising materials. The aim of this paper is to review the modification performed in GIC-based materials to improve their physicochemical properties. PMID:27428956

Non-destructive testing techniques based on nonlinear methods for assessment of debonding in single lap joints

NASA Astrophysics Data System (ADS)

Scarselli, G.; Ciampa, F.; Ginzburg, D.; Meo, M.

2015-04-01

Nonlinear ultrasonic non-destructive evaluation (NDE) methods can be used for the identification of defects within adhesive bonds as they rely on the detection of nonlinear elastic features for the evaluation of the bond strength. In this paper the nonlinear content of the structural response of a single lap joint subjected to ultrasonic harmonic excitation is both numerically and experimentally evaluated to identify and characterize the defects within the bonded region. Different metallic samples with the same geometry were experimentally tested in order to characterize the debonding between two plates by using two surface bonded piezoelectric transducers in pitch-catch mode. The dynamic response of the damaged samples acquired by the single receiver sensor showed the presence of higher harmonics (2nd and 3rd) and subharmonics of the fundamental frequencies. These nonlinear elastic phenomena are clearly due to nonlinear effects induced by the poor adhesion between the two plates. A new constitutive model aimed at representing the nonlinear material response generated by the interaction of the ultrasonic waves with the adhesive joint is also presented. Such a model is implemented in an explicit FE software and uses a nonlinear user defined traction-displacement relationship implemented by means of a cohesive material user model interface. The developed model is verified for the different geometrical and material configurations. Good agreement between the experimental and numerical nonlinear response showed that this model can be used as a simple and useful tool for understanding the quality of the adhesive joint.

Determinants of and inequalities in self-perceived health in Ukraine.

PubMed

Gilmore, Anna B C; McKee, Martin; Rose, Richard

2002-12-01

Ukraine is the second most populous of the former Soviet Republics and since transition its economy has fared even more poorly than Russia. Although the impact of the collapse of the former Soviet Union on health in Russia has been investigated, little is known of its impact in other post-Soviet republics. We report a cross-sectional study undertaken in Ukraine in March 2000. A multi-stage random sampling technique was used and 1600 interviews completed (72% response rate) with a representative national sample of Ukrainian adults. We investigated socioeconomic and psychosocial determinants of self-perceived health, which has been shown to be a valid and reliable measure of overall health and predictive of mortality. Odds ratios for less than good physical health were calculated using logistic regression. The self-rated health of Ukrainians was poor, 25% of men and 43% of women rated their health as poor or very poor. This is worse than levels recorded in Russia and considerably worse than levels seen in western Europe. Marked gender, geographical and socioeconomic inequalities in health were recorded. Women are at increased risk of poor self-rated health compared with men (OR 3.58, 2.50-5.14) as are women living in villages compared with those in cities (OR 3.24, 1.30-8.07). Socioeconomic factors including poor material situation (OR 1.64, 1.01-2.67), and psychosocial factors including low control over life (OR 1.89, 1.15-3.11) were identified as independent health determinants. Control over life was found to account for the negative impact of low social position on health. Good family relations protected against poor health. The findings suggest that a decrease in control, arising from an increasingly uncertain political and economic environment, a reduction in material wealth and the stress of change may all have contributed to the decline in life expectancy seen with transition. Copyright 2002 Elsevier Science Ltd.

An audit of diabetes care at 3 centres in Alexandria.

PubMed

Abou El-Enein, N Y; Abolfotouh, M A

2008-01-01

Selected indicators for structure, process and outcome of care were used to audit diabetes care in 3 centres in Alexandria. Structure was poor: main problems included absence of appointment and recall system, deficiencies in laboratory resources and lack of educational material. Process of care was poor for 69.2% of patients: deficiencies included absence of essential information in records and missing some essential clinical examinations. Degree of control was poor for 49.2% of patients and only 30.6% had no complications. Compliance to appointment was good for about 80% of patients. Better outcome (fewer complications and higher compliance) was significantly associated with poor process of care. This cannot, however, be considered a valid predictor of outcome as good care might be initiated by the presence of complications.

The weak interfaces within tough natural composites: experiments on three types of nacre.

PubMed

Khayer Dastjerdi, Ahmad; Rabiei, Reza; Barthelat, Francois

2013-03-01

Mineralization is a typical strategy used in natural materials to achieve high stiffness and hardness for structural functions such as skeletal support, protection or predation. High mineral content generally leads to brittleness, yet natural materials such as bone, mollusk shells or glass sponge achieve relatively high toughness considering the weakness of their constituents through intricate microstructures. In particular, nanometers thick organic interfaces organized in micro-architectures play a key role in providing toughness by various processes including crack deflection, crack bridging or energy dissipation. While these interfaces are critical in these materials, their composition, structure and mechanics is often poorly understood. In this work we focus on nacre, one of the most impressive hard biological materials in terms of toughness. We performed interfacial fracture tests on chevron notched nacre samples from three different species: red abalone, top shell and pearl oyster. We found that the intrinsic toughness of the interfaces is indeed found to be extremely low, in the order of the toughness of the mineral inclusions themselves. Such low toughness is required for the cracks to follow the interfaces, and to deflect and circumvent the mineral tablets. This result highlights the efficacy of toughening mechanisms in natural materials, turning low-toughness inclusions and interfaces into high-performance composites. We found that top shell nacre displayed the highest interfacial toughness, because of higher surface roughness and a more resilient organic material, and also through extrinsic toughening mechanisms including crack deflection, crack bridging and process zone. In the context of biomimetics, the main implication of this finding is that the interface in nacre-like composite does not need to be tough; the extensibility or ductility of the interfaces may be more important than their strength and toughness to produce toughness at the macroscale. Copyright © 2012 Elsevier Ltd. All rights reserved.

Readability of patient education materials on the American Orthopaedic Society for Sports Medicine website.

PubMed

Eltorai, Adam E M; Han, Alex; Truntzer, Jeremy; Daniels, Alan H

2014-11-01

The recommended readability of patient education materials by the American Medical Association (AMA) and National Institutes of Health (NIH) should be no greater than a sixth-grade reading level. However, online resources may be too complex for some patients to understand, and poor health literacy predicts inferior health-related quality of life outcomes. This study evaluated whether the American Orthopaedic Society for Sports Medicine (AOSSM) website's patient education materials meet recommended readability guidelines for medical information. We hypothesized that the readability of these online materials would have a Flesch-Kincaid formula grade above the sixth grade. All 65 patient education entries of the AOSSM website were analyzed for grade level readability using the Flesch-Kincaid formula, a widely used and validated tool to evaluate the text reading level. The average (standard deviation) readability of all 65 articles was grade level 10.03 (1.44); 64 articles had a readability score above the sixth-grade level, which is the maximum level recommended by the AMA and NIH. Mean readability of the articles exceeded this level by 4.03 grade levels (95% CI, 3.7-4.4; P < 0.0001). We found post-hoc that only 7 articles had a readability score ≤ an eighth-grade level, the average reading level of US adults. Mean readability of the articles exceeded this level by 2.03 grade levels (95% CI, 1.7-2.4; P < 0.0001). The readability of online AOSSM patient education materials exceeds the readability level recommended by the AMA and NIH, and is above the average reading level of the majority of US adults. This online information may be of limited utility to most patients due to a lack of comprehension. Our study provides a clear example of the need to improve the readability of specific education material in order to maximize the efficacy of multimedia sources.

Discrimination of poorly exposed lithologies in AVIRIS data

NASA Technical Reports Server (NTRS)

Farrand, William H.; Harsanyi, Joseph C.

1993-01-01

One of the advantages afforded by imaging spectrometers such as AVIRIS is the capability to detect target materials at a sub-pixel scale. This paper presents several examples of the identification of poorly exposed geologic materials - materials which are either subpixel in scale or which, while having some surface expression over several pixels, are partially covered by vegetation or other materials. Sabol et al. (1992) noted that a primary factor in the ability to distinguish sub-pixel targets is the spectral contrast between the target and its surroundings. In most cases, this contrast is best expressed as an absorption feature or features present in the target but absent in the surroundings. Under such circumstances, techniques such as band depth mapping (Clark et al., 1992) are feasible. However, the only difference between a target material and its surroundings is often expressed solely in the continuum. We define the 'continuum' as the reflectance or radiance spanning spectral space between spectral features. Differences in continuum slope and shape can only be determined by reduction techniques which considers the entire spectral range; i.e., techniques such as spectral mixture analysis (Adams et al., 1989) and recently developed techniques which utilize an orthogonal subspace projection operator (Harsanyi, 1993). Two of the three examples considered herein deal with cases where the target material differs from its surroundings only by such a subtle continuum change.

A historical and socioeconomic analysis of occupational safety and health in India.

PubMed

Vilanilam, J V

1980-01-01

Workers in poor countries of the so-called Third World are more likely to be affected by the dangers of high technology than their counterparts in wealthier countries. Owing to their lack of education, most workers in the "developing" world are unaware of the hazards of their occupations. Moreover, their general backwardness in sanitation and nutrition and climatic proneness of their geographic region to epidemics cause diseases contracted from the work environment to be aggravated. occupational diseases are often misconstrued as diseases resulting from the general environment. Since unemployment in underdeveloped countries is of a very high order, workers are prepared to accept any job, irrespective of the dangers involved. Labor is cheap and easily replaceable, so employers see no need for improving occupational safety and health. Labor unions are mostly controlled by full-time politicians who consider health a political issue, especially when their party controls the country's government. The seriousness of all these factors is heightened by the existing socioeconomic order in poor countries, in which national medievalism and multinational modernism play a crucial role. In order to understand the prevailing socioeconomic order, one has to analyze the social structures of poor countries in the context of today's world economic structure. India is taken as an example of a "developing" country where all the above-mentioned factors and many others are in operation: backwardness of the worker; poor nutrition; lack of concern for public health; proneness to epidemics; and indifference on the part of employers, politicians, and unions toward occupational health; high unemployment, control of the local economy by multinational corporations; and control of the mass media by feudalistic vested interests. This article attempts to analyze the occupational health and safety issue in India from a historical perspective, and stresses the vital need of structural changes in various fields so that workers can have a safe and healthy working environment.

Embryonic and postnatal telomere length decrease with ovulation order within clutches

PubMed Central

Noguera, José C.; Metcalfe, Neil B.; Reichert, Sophie; Monaghan, Pat

2016-01-01

Telomere length (TL) in early life has been found to be predictive of subsequent lifespan. Factors such as parental TL, parental age and environmental conditions during development have been shown to contribute to the observed variation in TL among individuals. One factor that has not hitherto been considered is ovulation order, although it is well established that the last hatched/born offspring in a brood or litter often show relatively poor subsequent performance. We examined the within- and across-clutch effect of ovulation order on TL in embryos of zebra finches experiencing the same controlled incubation conditions (N = 151), and tested whether any such ovulation order effects remained detectable in adults (N = 122). Irrespective of clutch and egg size, TL in early-stage embryos (72 h incubation) markedly decreased with within-clutch ovulation order; the difference in TL of first and last-laid embryos was equivalent to the average within-individual telomere loss over the entire period of nestling and juvenile life. This ovulation-order effect occurred only within but not across clutches, and was still evident in adults. Given that TL in early life predicts lifespan, our results suggest that parental effects on telomere length could contribute to the known poor performance of later-ovulated family members. PMID:27174767

Structural damages of L'Aquila (Italy) earthquake

NASA Astrophysics Data System (ADS)

Kaplan, H.; Bilgin, H.; Yilmaz, S.; Binici, H.; Öztas, A.

2010-03-01

On 6 April 2009 an earthquake of magnitude 6.3 occurred in L'Aquila city, Italy. In the city center and surrounding villages many masonry and reinforced concrete (RC) buildings were heavily damaged or collapsed. After the earthquake, the inspection carried out in the region provided relevant results concerning the quality of the materials, method of construction and the performance of the structures. The region was initially inhabited in the 13th century and has many historic structures. The main structural materials are unreinforced masonry (URM) composed of rubble stone, brick, and hollow clay tile. Masonry units suffered the worst damage. Wood flooring systems and corrugated steel roofs are common in URM buildings. Moreover, unconfined gable walls, excessive wall thicknesses without connection with each other are among the most common deficiencies of poorly constructed masonry structures. These walls caused an increase in earthquake loads. The quality of the materials and the construction were not in accordance with the standards. On the other hand, several modern, non-ductile concrete frame buildings have collapsed. Poor concrete quality and poor reinforcement detailing caused damage in reinforced concrete structures. Furthermore, many structural deficiencies such as non-ductile detailing, strong beams-weak columns and were commonly observed. In this paper, reasons why the buildings were damaged in the 6 April 2009 earthquake in L'Aquila, Italy are given. Some suggestions are made to prevent such disasters in the future.

First-principles study on the stability and magnetoelectric properties of multiferroic materials XTiO3 (X = Mn, Fe, Co, Ni)

NASA Astrophysics Data System (ADS)

Chen, Xing-Yuan; Lai, Guo-Xia; Gu, Di; Zhu, Wei-Ling; Lai, Tian-Shu; Zhao, Yu-Jun

2018-04-01

The XTiO3 (X = Mn, Fe, Co and Ni) materials with R3c structure could be grown under critical conditions based on first-principles calculations and thermodynamic stability analysis. FeTiO3 and MnTiO3 could be synthesized relatively easily under metal-rich and O-poor conditions, while NiTiO3 could be stable under Ni-rich, O-rich and Ti-poor conditions. The predicted R3c CoTiO3 under thermodynamic equilibrium conditions is suggested to be synthesized under Co-rich, O-rich and Ti-poor conditions, but the calculated phonon dispersion indicates R3c CoTiO3 becomes unstable under the dynamical conditions. The ferroelectric behavior in the XTiO3 (X = Mn, Fe, Co and Ni) system could be dominated by the Ti ion with d0 state and the strong hybridization between Ti and O, while the magnetic property is mainly caused by the contribution of 3d transition metal.

Identifying the poorest older Americans.

PubMed

Fisher, Jonathan D; Johnson, David S; Marchand, Joseph T; Smeeding, Timothy M; Torrey, Barbara B

2009-11-01

Public policies target a subset of the population defined as poor or needy, but rarely are people poor or needy in the same way. This is particularly true among older adults. This study investigates poverty among older adults in order to identify who among them is financially worst off. We use 20 years of data from the Consumer Expenditure Survey to examine the income and consumption of older Americans. The poverty rate is cut in fourth if both income and consumption are used to define poverty. Those most likely to be poor defined by only income but not poor defined by income and consumption together are married, White, and homeowners and have a high school diploma or higher. The income poor alone display sufficient assets to raise consumption above poverty thresholds, whereas the consumption poor are shown to have income just above the poverty threshold and few assets. The poorest among the older population are those who are income and consumption poor. Understanding the nature of this double poverty population is important in measuring the success of future public policies to reduce poverty among this group.

Insoluble drug delivery strategies: review of recent advances and business prospects

PubMed Central

Kalepu, Sandeep; Nekkanti, Vijaykumar

2015-01-01

The emerging trends in the combinatorial chemistry and drug design have led to the development of drug candidates with greater lipophilicity, high molecular weight and poor water solubility. Majority of the failures in new drug development have been attributed to poor water solubility of the drug. Issues associated with poor solubility can lead to low bioavailability resulting in suboptimal drug delivery. About 40% of drugs with market approval and nearly 90% of molecules in the discovery pipeline are poorly water-soluble. With the advent of various insoluble drug delivery technologies, the challenge to formulate poorly water soluble drugs could be achieved. Numerous drugs associated with poor solubility and low bioavailabilities have been formulated into successful drug products. Several marketed drugs were reformulated to improve efficacy, safety and patient compliance. In order to gain marketing exclusivity and patent protection for such products, revitalization of poorly soluble drugs using insoluble drug delivery technologies have been successfully adopted by many pharmaceutical companies. This review covers the recent advances in the field of insoluble drug delivery and business prospects. PMID:26579474

Advanced study of thermal behaviour of CSZ comparing with the classic YSZ coating

NASA Astrophysics Data System (ADS)

Dragomirescu, A.; Constantin, N.; Ştefan, A.; Manoliu, V.; Truşcă, R.

2017-01-01

Thermal barrier coatings (TBC) are advanced materials typically applied to metal surfaces subjected to extreme temperatures to protect them and increase their lifetime. Ceria stabilized zirconia ceramic layer (CSZ) is increasingly used as an alternative improved as replace for classical TBC system - yttria stabilized zirconia - thanks to superior properties, including mechanical and high resistance to thermal corrosion. The paper describes the thermal shock testing of two types of thermal barrier coatings used to protect a nickel super alloy. For the experimental procedure, it was used plate samples from nickel super alloy with a bond coat and a ceramic top coat. The top coat was different: on some samples, it was used YSZ and on others CSZ. Ni based super alloys have good corrosion resistance in reducing environments action, but poor in oxidizing conditions. Extreme environments can lead to loss of material by oxidation / corrosion, along with decreased mechanical properties of the substrate due to damaging elements which diffuses into the substrate at high temperatures. Using laboratory equipment, the TBC systems were exposed repeatedly to extreme high temperatures for a short time and then cooled. After the thermal shock tests, the samples were morph-structured characterized using electronic microscopy to analyze the changes. The experimental results were compared to rank the TBC systems in order of performance.

Influence of heat-treated Al-Si coating on the weldability and microstructural inhomogeneity for hot stamped steel resistance nut projection welds

NASA Astrophysics Data System (ADS)

Chun, Eun-Joon; Lim, Sung-Sang; Kim, Young-Tae; Nam, Ki-Sung; Kim, Young-Min; Park, Young-Whan; Murugan, Siva Prasad; Park, Yeong-Do

2018-03-01

Resistance nut projection weldability of Al-Si coated hot stamped steel (HSS) was investigated under the viewpoint of weldable current range and joint strength (pull-out load). The microstructural inhomogeneities in the welds were also studied in order to elucidate the factors affecting the joint strength of the welds. The weldability of the given Al-Si coated HSS was compared with the weldability of an identical HSS without the Al-Si coating (Al-Si coating was polished out) and Zn coated dual phase steel. The weldable current range of Al-Si coated HSS was found to be narrower than that of the other materials. Furthermore, the average pull-out load within the weldable current range of the Al-Si coated HSS was the lowest among the three materials. The reason for poor weld mechanical property of the Al-Si coated hot-stamped steel was attributed to the microstructural inhomogeneities such as unmixed Al-Si coating layer at the edge of the nugget and the second phase Fe3(Al, Si) intermetallic compound. The formation of Fe3(Al, Si) phase was attributed to the solidification segregation of Al and Si during the weld solidification and was confirmed with the numerical analysis of solidification segregation.

Type of motion and lubricant in wear simulation of polyethylene acetabular cup.

PubMed

Saikko, V; Ahlroos, T

1999-01-01

The wear of ultra-high molecular weight polyethylene, the most commonly used bearing material in prosthetic joints, is often substantial, posing a significant clinical problem. For a long time, there has been a need for simple but still realistic wear test devices for prosthetic joint materials. The wear factors produced by earlier reciprocating and unidirectionally rotating wear test devices for polyethylene are typically two orders of magnitude too low, both in water and in serum lubrication. Wear is negligible even under multidirectional motion in water. A twelve-station, circularly translating pin-on-disc (CTPOD) device and a modification of the established biaxial rocking motion hip joint simulator were built. With these simple and inexpensive devices, and with the established three-axis hip joint simulator, realistic wear simulation was achieved. This was due to serum lubrication and to the fact that the direction of sliding constantly changed relative to the polyethylene specimen. The type and magnitude of load was found to be less important. The CTPOD tests showed that the subsurface brittle region, which results from gamma irradiation sterilization of polyethylene in air, has poor wear resistance. Phospholipid and soy protein lubrication resulted in unrealistic wear. The introduction of devices like CTPOD may boost wear studies, rendering them feasible without heavy investment.

Enhanced UV light detection using a p-terphenyl wavelength shifter

NASA Astrophysics Data System (ADS)

Joosten, S.; Kaczanowicz, E.; Ungaro, M.; Rehfuss, M.; Johnston, K.; Meziani, Z.-E.

2017-10-01

UV-glass photomultiplier tubes (PMTs) have poor photon detection efficiency for wavelengths below 300 nm due to the opaqueness of the window material. Costly quartz PMTs could be used to enhance the efficiency below 300 nm. A less expensive solution that dramatically improves this efficiency is the application of a thin film of a p-terphenyl (PT) wavelength shifter on UV-glass PMTs. This improvement was quantified for Photonis XP4500B PMTs for wavelengths between 200 nm and 400 nm. The gain factor ranges up to 5 . 4 ± 0 . 5 at a wavelength of 215 nm, with a material load of 110 ± 10 μg /cm2 (894 nm). The wavelength shifter was found to be fully transparent for wavelengths greater than 300 nm. The resulting gain in detection efficiency, when used in a typical C̆erenkov counter, was estimated to be of the order of 40%. Consistent coating quality was assured by a rapid gain testing procedure using narrow-band UV LEDs. Based on these results, 200 Photonis XP4500B PMTs were treated with PT for the upgraded low-threshold C̆erenkov counter (LTCC) to be used in the CEBAF Large Acceptance Spectrometer upgraded detector (CLAS12) at the Thomas Jefferson National Accelerator Facility.

Thin films of fullerene-like MoS2 nanoparticles with ultra-low friction and wear

PubMed

Chhowalla; Amaratunga

2000-09-14

The tribological properties of solid lubricants such as graphite and the metal dichalcogenides MX2 (where M is molybdenum or tungsten and X is sulphur or selenium) are of technological interest for reducing wear in circumstances where liquid lubricants are impractical, such as in space technology, ultra-high vacuum or automotive transport. These materials are characterized by weak interatomic interactions (van der Waals forces) between their layered structures, allowing easy, low-strength shearing. Although these materials exhibit excellent friction and wear resistance and extended lifetime in vacuum, their tribological properties remain poor in the presence of humidity or oxygen, thereby limiting their technological applications in the Earth's atmosphere. But using MX2 in the form of isolated inorganic fullerene-like hollow nanoparticles similar to carbon fullerenes and nanotubes can improve its performance. Here we show that thin films of hollow MoS2 nanoparticles, deposited by a localized high-pressure arc discharge method, exhibit ultra-low friction (an order of magnitude lower than for sputtered MoS2 thin films) and wear in nitrogen and 45% humidity. We attribute this 'dry' behaviour in humid environments to the presence of curved S-Mo-S planes that prevent oxidation and preserve the layered structure.

Dynamic molecular structure of plant biomass-derived black carbon (biochar)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keiluweit, M.; Nico, P.S.; Johnson, M.G.

2009-11-15

Char black carbon (BC), the solid residue of incomplete combustion, is continuously being added to soils and sediments due to natural vegetation fires, anthropogenic pollution, and new strategies for carbon sequestration ('biochar'). Here we present a molecular-level assessment of the physical organization and chemical complexity of biomass-derived chars and, specifically, that of aromatic carbon in char structures. BET-N{sub 2} surface area, X-ray diffraction (XRD), synchrotron-based Near-edge X-ray Absorption Fine Structure (NEXAFS), and Fourier transform infrared (FT-IR) spectroscopy are used to show how two plant materials (wood and grass) undergo analogous, but quantitatively different physical-chemical transitions as charring temperature increases frommore » 100 to 700 C. These changes suggest the existence of four distinct categories of char consisting of a unique mixture of chemical phases and physical states: (i) in transition chars the crystalline character of the precursor materials is preserved, (ii) in amorphous chars the heat-altered molecules and incipient aromatic polycondensates are randomly mixed, (iii) composite chars consist of poorly ordered graphene stacks embedded in amorphous phases, and (iv) turbostratic chars are dominated by disordered graphitic crystallites. The molecular variations among the different char categories translate into differences in their ability to persist in the environment and function as environmental sorbents.« less

Thin films of fullerene-like MoS2 nanoparticles with ultra-low friction and wear

NASA Astrophysics Data System (ADS)

Chhowalla, Manish; Amaratunga, Gehan A. J.

2000-09-01

The tribological properties of solid lubricants such as graphite and the metal dichalcogenides MX2 (where M is molybdenum or tungsten and X is sulphur or selenium) are of technological interest for reducing wear in circumstances where liquid lubricants are impractical, such as in space technology, ultra-high vacuum or automotive transport. These materials are characterized by weak interatomic interactions (van der Waals forces) between their layered structures, allowing easy, low-strength shearing. Although these materials exhibit excellent friction and wear resistance and extended lifetime in vacuum, their tribological properties remain poor in the presence of humidity or oxygen, thereby limiting their technological applications in the Earth's atmosphere. But using MX2 in the form of isolated inorganic fullerene-like hollow nanoparticles similar to carbon fullerenes and nanotubes can improve its performance. Here we show that thin films of hollow MoS2 nanoparticles, deposited by a localized high-pressure arc discharge method, exhibit ultra-low friction (an order of magnitude lower than for sputtered MoS2 thin films) and wear in nitrogen and 45% humidity. We attribute this `dry' behaviour in humid environments to the presence of curved S-Mo-S planes that prevent oxidation and preserve the layered structure.

Nanocomposites biodegradable coating on BOPET films to enhance hot seal strength properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barbaro, G., E-mail: giovannibarbaro@email.it; Galdi, M. R., E-mail: mrgaldi@unisa.it; Di Maio, L., E-mail: ldimaio@unisa.it

2015-12-17

The coating technology is a strategic solution to improve the properties of flexible packaging films. Indeed, additional functional layers are often designed and added as coating on the substrate, in order to improve the characteristic of the flexible packaging and to meet the requirements for the desired gas or vapour barrier, for adhesion and sealing, or for improving the film printability, its aesthetics and durability. Moreover, this technology allows to functionalize a polymeric substrate applying materials with different chemistry, rheology, thermal and structural characteristics. BOPET films are widely used for food packaging applications thanks to their good gas barrier andmore » mechanical properties, high transparency and for the excellent printability. In regard to sealing performance, BOPET films show poor sealing properties so they are mostly submitted to lamination processes with polyethylene. Nevertheless, this solution compromises the PET recyclability and influences the gas permeability of the multilayer PET based structures. The aim of this work is to investigate on the effect of nanocomposite biodegradable coatings for BOPET substrates in enhancing the heat sealing strength of eco-compatible PET/PLA films. At this regards, different percentages of Cloisite C30B (0%, 2% and 4%{sub wt/wt}) have been added to PLA by solution intercalation technique and the nanocomposite biodegradable materials produced have been applied on BOPET commercial films by casting. The BOPET coated films have been characterized in order to evaluate the heat sealing strength and the mechanical, gas permeability and surface properties. The results have shown that the addition of nanoclay in PLA coating significantly enhance the hot tack properties of the PET/PLA system produced, while the oxygen and water vapour permeability are slightly increased if compared to pure BOPET films.« less

Development and Evaluation of Titanium Space Suit Bearings

NASA Technical Reports Server (NTRS)

Rhodes, Richard; Battisti, Brian; Ytuarte, Ray, Jr.; Schultz, Bradley

2016-01-01

The Z-2 Prototype Planetary Extravehicular Space Suit Assembly is a continuation of NASA's Z series of spacesuits, designed with the intent of meeting a wide variety of exploration mission objectives, including human exploration of the Martian surface. Incorporating titanium bearings into the Z series space suit architecture allows us to reduce mass by an estimated 23 pounds per suit system compared to the previously used stainless steel bearing designs without compromising suit functionality. There are two obstacles to overcome when using titanium for a bearing race: 1) titanium is flammable when exposed to the oxygen wetted environment inside the space suit and 2) titanium's poor wear properties are often challenging to overcome in tribology applications. In order to evaluate the ignitability of a titanium space suit bearing, a series of tests were conducted at White Sands Test Facility that introduced the bearings to an extreme test profile, with multiple failures imbedded into the test bearings. The testing showed no signs of ignition in the most extreme test cases; however, substantial wear of the bearing races was observed. In order to design a bearing that can last an entire exploration mission (approximately 2 years), bearing test rigs were developed that allow for the quick evaluation of various bearing ball loads, ball diameters, lubricants, and surface treatments. This test data will allow designers to minimize the titanium bearing mass for a specific material and lubricant combination around a maximum contact stress that will allow the bearing to survive the life of an exploration mission. This paper reviews the current research and testing that has been performed on titanium bearing races to evaluate the use of such materials in an enriched oxygen environment and to optimize the bearing assembly mass and tribological properties to accommodate for the high bearing cycle life for an exploration mission.

Viscosity of α-pinene secondary organic material and implications for particle growth and reactivity

PubMed Central

Renbaum-Wolff, Lindsay; Grayson, James W.; Bateman, Adam P.; Kuwata, Mikinori; Sellier, Mathieu; Murray, Benjamin J.; Shilling, John E.; Martin, Scot T.; Bertram, Allan K.

2013-01-01

Particles composed of secondary organic material (SOM) are abundant in the lower troposphere. The viscosity of these particles is a fundamental property that is presently poorly quantified yet required for accurate modeling of their formation, growth, evaporation, and environmental impacts. Using two unique techniques, namely a “bead-mobility” technique and a “poke-flow” technique, in conjunction with simulations of fluid flow, the viscosity of the water-soluble component of SOM produced by α-pinene ozonolysis is quantified for 20- to 50-μm particles at 293–295 K. The viscosity is comparable to that of honey at 90% relative humidity (RH), similar to that of peanut butter at 70% RH, and at least as viscous as bitumen at ≤30% RH, implying that the studied SOM ranges from liquid to semisolid or solid across the range of atmospheric RH. These data combined with simple calculations or previous modeling studies are used to show the following: (i) the growth of SOM by the exchange of organic molecules between gas and particle may be confined to the surface region of the particles for RH ≤ 30%; (ii) at ≤30% RH, the particle-mass concentrations of semivolatile and low-volatility organic compounds may be overpredicted by an order of magnitude if instantaneous equilibrium partitioning is assumed in the bulk of SOM particles; and (iii) the diffusivity of semireactive atmospheric oxidants such as ozone may decrease by two to five orders of magnitude for a drop in RH from 90% to 30%. These findings have possible consequences for predictions of air quality, visibility, and climate. PMID:23620520

Nanocomposites biodegradable coating on BOPET films to enhance hot seal strength properties

NASA Astrophysics Data System (ADS)

Barbaro, G.; Galdi, M. R.; Di Maio, L.; Incarnato, L.

2015-12-01

The coating technology is a strategic solution to improve the properties of flexible packaging films. Indeed, additional functional layers are often designed and added as coating on the substrate, in order to improve the characteristic of the flexible packaging and to meet the requirements for the desired gas or vapour barrier, for adhesion and sealing, or for improving the film printability, its aesthetics and durability. Moreover, this technology allows to functionalize a polymeric substrate applying materials with different chemistry, rheology, thermal and structural characteristics. BOPET films are widely used for food packaging applications thanks to their good gas barrier and mechanical properties, high transparency and for the excellent printability. In regard to sealing performance, BOPET films show poor sealing properties so they are mostly submitted to lamination processes with polyethylene. Nevertheless, this solution compromises the PET recyclability and influences the gas permeability of the multilayer PET based structures. The aim of this work is to investigate on the effect of nanocomposite biodegradable coatings for BOPET substrates in enhancing the heat sealing strength of eco-compatible PET/PLA films. At this regards, different percentages of Cloisite C30B (0%, 2% and 4%wt/wt) have been added to PLA by solution intercalation technique and the nanocomposite biodegradable materials produced have been applied on BOPET commercial films by casting. The BOPET coated films have been characterized in order to evaluate the heat sealing strength and the mechanical, gas permeability and surface properties. The results have shown that the addition of nanoclay in PLA coating significantly enhance the hot tack properties of the PET/PLA system produced, while the oxygen and water vapour permeability are slightly increased if compared to pure BOPET films.

Strong room-temperature ferromagnetism in VSe2 monolayers on van der Waals substrates

NASA Astrophysics Data System (ADS)

Bonilla, Manuel; Kolekar, Sadhu; Ma, Yujing; Diaz, Horacio Coy; Kalappattil, Vijaysankar; Das, Raja; Eggers, Tatiana; Gutierrez, Humberto R.; Phan, Manh-Huong; Batzill, Matthias

2018-04-01

Reduced dimensionality and interlayer coupling in van der Waals materials gives rise to fundamentally different electronic1, optical2 and many-body quantum3-5 properties in monolayers compared with the bulk. This layer-dependence permits the discovery of novel material properties in the monolayer regime. Ferromagnetic order in two-dimensional materials is a coveted property that would allow fundamental studies of spin behaviour in low dimensions and enable new spintronics applications6-8. Recent studies have shown that for the bulk-ferromagnetic layered materials CrI3 (ref. 9) and Cr2Ge2Te6 (ref. 10), ferromagnetic order is maintained down to the ultrathin limit at low temperatures. Contrary to these observations, we report the emergence of strong ferromagnetic ordering for monolayer VSe2, a material that is paramagnetic in the bulk11,12. Importantly, the ferromagnetic ordering with a large magnetic moment persists to above room temperature, making VSe2 an attractive material for van der Waals spintronics applications.

Bed material transport in the Virgin River, Utah

USGS Publications Warehouse

Andrews, E.D.

2000-01-01

Detailed information concerning the rate and particle size distribution of bed material transport by streamflows can be very difficult and expensive to obtain, especially where peak streamflows are brief and bed material is poorly sorted, including some very large boulders. Such streams, however, are common in steep, arid watersheds. Any computational approach must consider that (1) only the smaller particle sizes present on the streambed move even during large floods and (2) the largest bed particles exert a significant form drag on the flow. Conventional methods that rely on a single particle size to estimate the skin friction shear stress acting on the mobile fraction of the bed material perform poorly. Instead, for this study, the skin friction shear stress was calculated for the observed range of streamflows by calculating the form drag exerted on the reach‐averaged flow field by all particle sizes. Suspended and bed load transported rates computed from reach‐averaged skin friction shear stress are in excellent agreement with measured transport rates. The computed mean annual bed material load, including both bed load and suspended load, of the East Fork Virgin River for the water years 1992‐1996 was approximately 1.3×10 5 t. A large portion of the bed material load consists of sand‐sized particles, 0.062–1.0 mm in diameter, that are transported in suspension. Such particles, however, constituted only 10% of the surface bed material and less than 25% of the subsurface bed material. The mean annual quantity of bed load transported was 1060 t/yr with a median size of 15 mm.

Phototropic liquid crystal materials containing naphthopyran dopants

NASA Astrophysics Data System (ADS)

Rumi, Mariacristina; Cazzell, Seth; Kosa, Tamas; Sukhomlinova, Ludmila; Taheri, Bahman; Bunning, Timothy; White, Timothy

2015-03-01

Dopant molecules dispersed in a liquid crystalline material usually affects the order of the system and the transition temperature between various phases. If the dopants undergo photoisomerization between conformers with different shapes, the interactions with the liquid crystal molecules can be different for the material in the dark and during exposure to light of appropriate wavelength. This can be used to achieve isothermal photoinduced phase transitions (phototropism). With proper selection of materials components, both order-to-disorder and disorder-to-order photoinduced transition have been demonstrated. Isothermal order-increasing transitions have been observed recently using naphthopyran derivatives as dopants. We are investigating the changes in order parameter and transition temperature of liquid crystal mixtures containing naphthopyrans and how they are related to exposure conditions and to the concentration and molecular structure of the dopants. We are also studying the nature of the photoinduced phase transitions, and comparing the behavior with that of azobenzene-doped mixtures, in which exposure to light leads to a decrease, instead of an increase, in the order of the system.

Moving toward an Empowering Setting in a First Grade Classroom Serving Primarily Working Class and Working Poor Latina/o Children: An Exploratory Analysis

ERIC Educational Resources Information Center

Silva, Janelle M.; Langhout, Regina Day

2016-01-01

Empowering settings are important places for people to develop leadership skills in order to enact social change. Yet, due to socio-cultural constructions of childhood in the US, especially constructions around working class and working poor children of Color, they are often not seen as capable or competent change agents, or in need of being in…

A Robust and Engineerable Self-Assembling Protein Template for the Synthesis and Patterning of Ordered Nanoparticle Arrays

NASA Technical Reports Server (NTRS)

McMillan, R. Andrew; Howard, Jeanie; Zaluzec, Nestor J.; Kagawa, Hiromi K.; Li, Yi-Fen; Paavola, Chad D.; Trent, Jonathan D.

2004-01-01

Self-assembling biomolecules that form highly ordered structures have attracted interest as potential alternatives to conventional lithographic processes for patterning materials. Here we introduce a general technique for patterning materials on the nanoscale using genetically modified protein cage structures called chaperonins that self-assemble into crystalline templates. Constrained chemical synthesis of transition metal nanoparticles is specific to templates genetically functionalized with poly-Histidine sequences. These arrays of materials are ordered by the nanoscale structure of the crystallized protein. This system may be easily adapted to pattern a variety of materials given the rapidly growing list of peptide sequences selected by screening for specificity for inorganic materials.

Normal modes in an overmoded circular waveguide coated with lossy material

NASA Technical Reports Server (NTRS)

Lee, C. S.; Lee, S. W.; Chuang, S. L.

1985-01-01

The normal modes in an overmoded waveguide coated with a lossy material are analyzed, particularly for their attenuation properties as a function of coating material, layer thickness, and frequency. When the coating material is not too lossy, the low-order modes are highly attenuated even with a thin layer of coating. This coated guide serves as a mode suppressor of the low-order modes, which can be particularly useful for reducing the radar cross section (RCS) of a cavity structure such as a jet inlet. When the coating material is very lossy, low-order modes fall into two distinct groups: highly and lowly attenuated modes. However, as a/lambda (a = radius of the cylinder; lambda = the free-space wavelength) increases, the separation between these two groups becomes less distinctive. The attenuation constants of most of the low-order modes become small, and decrease as a function of lambda sup 2/a sup 3.

The New Room Arrangement as a Teaching Strategy = La Nueva Organizacion del Salon como Estrategia Educativa.

ERIC Educational Resources Information Center

Dodge, Diane Trister

Many typical classroom behavior problems--running in the classroom, inability to make choices, failure to stick with activities, fighting over toys, and poor use of materials-- can be traced to how the room is arranged and how materials are displayed. By making a few changes in the classroom environment, early childhood teachers can create a…

Effect of Improvised Instructional Materials on Students' Achievement in Geometry at the Upper Basic Education Level in Makurdi Metropolis, Benue State, Nigeria

ERIC Educational Resources Information Center

Iji, C. O.; Ogbole, P. O.; Uka, N. K.

2014-01-01

Among all approaches aimed at reducing poor mathematics achievement among the students, adoption of appropriate methods of teaching appears to be more rewarding. In this study, improvised instructional materials were used to ascertain students' geometry achievement at the upper basic education one. Two research questions were asked with associated…

Design, Fabrication, Characterization and Modeling of Integrated Functional Materials

DTIC Science & Technology

2013-10-01

coated microwire to change the temperature of an FBG. We show below that the proposed sensor probe, with a relatively poor thermal coupling with FBG...Seebeck coefficient and decreased thermal conductivity due to the phenomenological properties of nanometer length scales, including enhanced...nanocomposites as compared to bulk polycrystalline materials, in addition to similar thermal conductivities , results in enhanced room temperature ZT as

THREE GENERATIONS, CASE MATERIALS IN LOW INCOME URBAN LIVING.

ERIC Educational Resources Information Center

JEFFERS, CAMILLE

ONE IN A SERIES OF STUDIES OF THE CHILD REARING STUDY (CRS) OF LOW-INCOME FAMILIES IN WASHINGTON, D.C., THIS BOOKLET PRESENTS CASE MATERIALS TO ILLUSTRATE THE CRS THESIS THAT THERE IS A WIDE VARIABILITY IN BEHAVIOR AND OUTLOOK AMONG THE URBAN POOR, AND SUGGESTS SOME OF THE IMPLICATIONS OF THE CRS FINDINGS FOR PARENT AND FAMILY LIFE EDUCATION.…

Materials for Microfluidic Immunoassays: A Review.

PubMed

Mou, Lei; Jiang, Xingyu

2017-08-01

Conventional immunoassays suffer from at least one of these following limitations: long processing time, high costs, poor user-friendliness, technical complexity, poor sensitivity and specificity. Microfluidics, a technology characterized by the engineered manipulation of fluids in channels with characteristic lengthscale of tens of micrometers, has shown considerable promise for improving immunoassays that could overcome these limitations in medical diagnostics and biology research. The combination of microfluidics and immunoassay can detect biomarkers with faster assay time, reduced volumes of reagents, lower power requirements, and higher levels of integration and automation compared to traditional approaches. This review focuses on the materials-related aspects of the recent advances in microfluidics-based immunoassays for point-of-care (POC) diagnostics of biomarkers. We compare the materials for microfluidic chips fabrication in five aspects: fabrication, integration, function, modification and cost, and describe their advantages and drawbacks. In addition, we review materials for modifying antibodies to improve the performance of the reaction of immunoassay. We also review the state of the art in microfluidic immunoassays POC platforms, from the laboratory to routine clinical practice, and also commercial products in the market. Finally, we discuss the current challenges and future developments in microfluidic immunoassays. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Gas Separation Properties of Polyimide Thin Films on Ceramic Supports for High Temperature Applications

PubMed Central

Escorihuela, Sara; Brinkmann, Torsten

2018-01-01

Novel selective ceramic-supported thin polyimide films produced in a single dip coating step are proposed for membrane applications at elevated temperatures. Layers of the polyimides P84®, Matrimid 5218®, and 6FDA-6FpDA were successfully deposited onto porous alumina supports. In order to tackle the poor compatibility between ceramic support and polymer, and to get defect-free thin films, the effect of the viscosity of the polymer solution was studied, giving the entanglement concentration (C*) for each polymer. The C* values were 3.09 wt. % for the 6FDA-6FpDA, 3.52 wt. % for Matrimid®, and 4.30 wt. % for P84®. A minimum polymer solution concentration necessary for defect-free film formation was found for each polymer, with the inverse order to the intrinsic viscosities (P84® ≥ Matrimid® >> 6FDA-6FpDA). The effect of the temperature on the permeance of prepared membranes was studied for H2, CH4, N2, O2, and CO2. As expected, activation energy of permeance for hydrogen was higher than for CO2, resulting in H2/CO2 selectivity increase with temperature. More densely packed polymers lead to materials that are more selective at elevated temperatures. PMID:29518942

Structure-Property Relations in Carbon Nanotube Fibers by Downscaling Solution Processing.

PubMed

Headrick, Robert J; Tsentalovich, Dmitri E; Berdegué, Julián; Bengio, Elie Amram; Liberman, Lucy; Kleinerman, Olga; Lucas, Matthew S; Talmon, Yeshayahu; Pasquali, Matteo

2018-03-01

At the microscopic scale, carbon nanotubes (CNTs) combine impressive tensile strength and electrical conductivity; however, their macroscopic counterparts have not met expectations. The reasons are variously attributed to inherent CNT sample properties (diameter and helicity polydispersity, high defect density, insufficient length) and manufacturing shortcomings (inadequate ordering and packing), which can lead to poor transmission of stress and current. To efficiently investigate the disparity between microscopic and macroscopic properties, a new method is introduced for processing microgram quantities of CNTs into highly oriented and well-packed fibers. CNTs are dissolved into chlorosulfonic acid and processed into aligned films; each film can be peeled and twisted into multiple discrete fibers. Fibers fabricated by this method and solution-spinning are directly compared to determine the impact of alignment, twist, packing density, and length. Surprisingly, these discrete fibers can be twice as strong as their solution-spun counterparts despite a lower degree of alignment. Strength appears to be more sensitive to internal twist and packing density, while fiber conductivity is essentially equivalent among the two sets of samples. Importantly, this rapid fiber manufacturing method uses three orders of magnitude less material than solution spinning, expanding the experimental parameter space and enabling the exploration of unique CNT sources. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Oxygen vacancy doping of hematite analyzed by electrical conductivity and thermoelectric power measurements

NASA Astrophysics Data System (ADS)

Mock, Jan; Klingebiel, Benjamin; Köhler, Florian; Nuys, Maurice; Flohre, Jan; Muthmann, Stefan; Kirchartz, Thomas; Carius, Reinhard

2017-11-01

Hematite (α -F e2O3 ) is known for poor electronic transport properties, which are the main drawback of this material for optoelectronic applications. In this study, we investigate the concept of enhancing electrical conductivity by the introduction of oxygen vacancies during temperature treatment under low oxygen partial pressure. We demonstrate the possibility of tuning the conductivity continuously by more than five orders of magnitude during stepwise annealing in a moderate temperature range between 300 and 620 K. With thermoelectric power measurements, we are able to attribute the improvement of the electrical conductivity to an enhanced charge-carrier density by more than three orders of magnitude. We compare the oxygen vacancy doping of hematite thin films with hematite nanoparticle layers. Thereby we show that the dominant potential barrier that limits charge transport is either due to grain boundaries in hematite thin films or due to potential barriers that occur at the contact area between the nanoparticles, rather than the potential barrier within the small polaron hopping model, which is usually applied for hematite. Furthermore, we discuss the transition from oxygen-deficient hematite α -F e2O3 -x towards the magnetite F e3O4 phase of iron oxide at high density of vacancies.

Effectiveness of development-radio programming among poor farmers: a case study.

PubMed

Melkote, S R

1989-01-01

The number of radio receivers has increased 118% worldwide since 1966, and the penetration in developing countries is substantial and growing. Radio is much more effective then printed media with illiterate and neo- literate people in the 3rd world. A recent research project measured the effectiveness of a radio messages broadcast as part of an agricultural extension project. The radio component of an agricultural project in India, organized under the training and visit system of the World Bank ongoing to disseminate information on improved seeds, fertilizers, pesticides, and better cultivation methods to selected farmers was analyzed. The information was transferred in 2 steps, workshops and scheduled visits. The agricultural radio program broadcast the information every morning and was taped for the study. The data analysis for the study was limited to rice crop knowledge and technical terms associated with the extension materials. Most of the farmers were 45 years old or younger. 90% had less than 6 years of schooling. Most were poor and 94% owned less than 6 hectors of land. 96% of those interviewed were males, and over 50% listened to the radio broadcast everyday. The results indicate very little convergence between the extension source and the farmers. In order to communicate effectively, the proper subjects must be selected and presented in simple, colloquial, and familiar words. None of the material was tested, nor were the recipients involved in the process of message preparation. The study suggests that no matter what medium is used, message content and presentation have an important effect on the distribution of the information, and the comprehension and the behavior of the recipient. To be most effective it is important to study not only the content of the message, but the code, structure, and treatment, and to determine the extend of adequate comprehension of those with low literacy.

Far-ultraviolet to Near-infrared Spectroscopy of a Nearby Hydrogen-poor Superluminous Supernova Gaia16apd

NASA Astrophysics Data System (ADS)

Yan, Lin; Quimby, R.; Gal-Yam, A.; Brown, P.; Blagorodnova, N.; Ofek, E. O.; Lunnan, R.; Cooke, J.; Cenko, S. B.; Jencson, J.; Kasliwal, M.

2017-05-01

We report the first maximum-light far-ultraviolet (FUV) to near-infrared (NIR) spectra (1000 Å - 1.62 μm, rest) of a hydrogen-poor superluminous supernova, Gaia16apd. At z = 0.1018, it is the second closest and the UV brightest SLSN-I, with 17.4 mag in Swift UVW2 band at -11 days pre-maximum. The coordinated observations with HST, Palomar, and Keck were taken at -2 to +25 days. Assuming an exponential (or t 2) form, we derived the rise time of 33 days and the peak bolometric luminosity of 3 × 1044 erg s-1. At the maximum, the photospheric temperature and velocity are 17,000 K and 14,000 km s-1, respectively. The inferred radiative and kinetic energy are roughly 1 × 1051 and 2 × 1052 erg. Gaia16apd is extremely UV luminous, and emits 50% of its total luminosity at 1000-2500 Å. Compared to the UV spectra (normalized at 3100 Å) of well studied SN1992A (Ia), SN2011fe (Ia), SN1999em (IIP), and SN1993J (IIb), it has orders of magnitude more FUV emission. This excess is interpreted primarily as a result of weaker metal-line blanketing due to a much lower abundance of iron group elements in the outer ejecta. Because these elements originate either from the natal metallicity of the star, or have been newly produced, our observation provides direct evidence that little of these freshly synthesized material, including 56Ni, were mixed into the outer ejecta, and the progenitor metallicity is likely sub-solar. This disfavors Pair-instability Supernova models with helium core masses ≥slant 90 {M}⊙ , where substantial 56Ni material is produced. A higher photospheric temperature definitely contributes to the FUV excess from Gaia16apd. Compared with Gaia16apd, we find PS1-11bam is also UV luminous.

Microstructure Stability During Creep of Friction Stir Welded AA2024-T3 Alloy

NASA Astrophysics Data System (ADS)

Regev, Michael; Rashkovsky, Tal; Cabibbo, Marcello; Spigarelli, Stefano

2018-01-01

The poor weldability of the AA2024 aluminum alloy limits its use in industrial applications. Because friction stir welding (FSW) is a non-fusion welding process, it seems to be a promising solution for welding this alloy. In the current study, FSW was applied to butt weld AA2024-T3 aluminum alloy plates. Creep tests were conducted at 250 and at 315 °C on both the parent material and the friction stir welded specimens. The microstructures of the welded and non-welded AA2024-T3 specimens before and after the creep tests were studied and compared. A comprehensive transmission electron microscopy study together with a high-resolution scanning electron microscopy study and energy-dispersive x-ray spectroscopy analysis was conducted to investigate the microstructure stability. The parent material seems to contain two kinds of Cu-rich precipitates—coarse precipitates of a few microns each and uniformly dispersed fine nanosized precipitates. Unlike the parent material, the crept specimens were found to contain the two kinds of precipitates mentioned above together with platelet-like precipitates. In addition, extensive decoration of the grain boundaries with precipitates was clearly observed in the crept specimens. Controlled aging experiments for up to 280 h at the relevant temperatures were conducted on both the parent material and the welded specimens in order to isolate the contribution of exposure to high temperatures to the microstructure changes. TEM study showed the development of dislocation networks into a cellular dislocation structure in the case of the parent metal. Changes in the dislocation structure as a function of the creep strain and the FSW process were recorded. A detailed creep data analysis was conducted, taking into account the instability of the microstructure.

Anomaly Detection and Comparative Analysis of Hydrothermal Alteration Materials Trough Hyperspectral Multisensor Data in the Turrialba Volcano

NASA Astrophysics Data System (ADS)

Rejas, J. G.; Martínez-Frías, J.; Bonatti, J.; Martínez, R.; Marchamalo, M.

2012-07-01

The aim of this work is the comparative study of the presence of hydrothermal alteration materials in the Turrialba volcano (Costa Rica) in relation with computed spectral anomalies from multitemporal and multisensor data adquired in spectral ranges of the visible (VIS), short wave infrared (SWIR) and thermal infrared (TIR). We used for this purposes hyperspectral and multispectral images from the HyMAP and MASTER airborne sensors, and ASTER and Hyperion scenes in a period between 2002 and 2010. Field radiometry was applied in order to remove the atmospheric contribution in an empirical line method. HyMAP and MASTER images were georeferenced directly thanks to positioning and orientation data that were measured at the same time in the acquisition campaign from an inertial system based on GPS/IMU. These two important steps were allowed the identification of spectral diagnostic bands of hydrothermal alteration minerals and the accuracy spatial correlation. Enviromental impact of the volcano activity has been studied through different vegetation indexes and soil patterns. Have been mapped hydrothermal materials in the crater of the volcano, in fact currently active, and their surrounding carrying out a principal components analysis differentiated for a high and low absorption bands to characterize accumulations of kaolinite, illite, alunite and kaolinite+smectite, delimitating zones with the presence of these minerals. Spectral anomalies have been calculated on a comparative study of methods pixel and subpixel focused in thermal bands fused with high-resolution images. Results are presented as an approach based on expert whose main interest lies in the automated identification of patterns of hydrothermal altered materials without prior knowledge or poor information on the area.

Effect of reprocessing cycles on the degradation of polypropylene copolymer filled with talc or montmorillonite during injection molding process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Demori, R.; Mauler, R. S., E-mail: raquel.mauler@ufrgs.br; Ashton, E.

Mechanical recycling of polymeric materials is a favorable technique resulting in economic and environmental benefits, especially in the case of polymers with a high production volume as the polypropylene copolymer (PP). However, recycling by reprocessing techniques can lead to thermal, mechanical or thermo-oxidative degradation that can affect the structure of the polymer and subsequently the material properties. PP filled with montmorillonite (MMT) or talc are widely produced and studied, however, its degradation reactions by reprocessing cycles are poorly studied so far. In this study, the effects of reprocessing cycles in the structure and in the properties of the PP/MMT andmore » PP/Talc were evaluated. The samples were mixed with 5% talc or MMT Cloisite C15A in a twin-screw extrusion. After extrusion, this filled material was submitted to five reprocessing cycles through an injection molding process. In order to evaluate the changes induced by reprocessing techniques, the samples were characterized by DSC, FT-IR, Izod impact and tensile strength tests. The study showed that Young modulus, elongation at brake and Izod impact were not affected by reprocessing cycles, except when using talc. In this case, the elongation at brake reduced until the fourth cycle, showing rigidity increase. The DSC results showed that melting and crystallization temperature were not affected. A comparison of FT-IR spectra of the reprocessed indicated that in both samples, between the first and the fifth cycle, no noticeable change has occurred. Thus, there is no evidence of thermo oxidative degradation. In general, these results suggest that PP reprocessing cycles using MMT or talc does not change the material properties until the fifth cycle.« less

Chemical characterization of iron-mediated soil organic matter stabilization in tropical subsoils

NASA Astrophysics Data System (ADS)

Coward, E.; Plante, A. F.; Thompson, A.

2015-12-01

Tropical forest soils contribute disproportionately to the poorly-characterized and persistent deep soil carbon (C) pool. Highly-weathered and often extending one to two meters deep, these soils also contain an abundance of semicrystalline, Fe- and Al-containing short-range-order (SRO) minerals, metastable derivatives of framework silicate and ferromagnesian parent materials. SRO minerals are capable of soil organic matter (SOM) stabilization through sorption or co-precipitation, a faculty enhanced by their high specific surface area (SSA). As such, SRO-mediated organomineral associations may prove a critical, yet matrix-selective, driver of SOM stabilization capacity in tropical soils, particularly at depth. Surface (0-20 cm) and subsoil (50-80 cm) samples were taken from 20 quantitative soil pits dug in the Luquillo Critical Zone Observatory, located in northeast Puerto Rico. Soils were stratified across granodiorite and volcaniclastic parent materials, spanning primary mineral contents of 5 to 40%. Selective dissolution procedures were used to isolate distinct forms of Fe-C interactions: (1) sodium pyrophosphate to isolate organo-mineral complexes, (2) hydroxylamine and (3) oxalate to isolate SRO phases, and (4) inorganic dithionite to isolate crystalline Fe oxides. Extracts were analysed for dissolved organic C (DOC) and Fe and Al concentrations to estimate SOM associated with each mineral phase. Soils were also subjected to SSA analysis, 57Fe-Mössbauer spectroscopy and X-ray diffraction before and after extraction to determine the contribution of extracted mineral phases to SOM stabilization capacity. Preliminary results indicate a dominance of secondary (hydr)oxides and kaolin minerals in surface soils, strongly driven by parent material. With depth, however, we observe a marked shift towards SRO mineral phases across both parent materials, suggesting that SRO-mediated organomineral associations are significant contributors to observed C storage in tropical subsoils.

Development of innovative biopolymers and related composites for bone tissue regeneration: study of their interaction with human osteoprogenitor cells.

PubMed

Basile, Maria Assunta; d'Ayala, Giovanna Gomez; Laurienzo, Paola; Malinconico, Mario; Della Ragione, Fulvio; Oliva, Adriana

2012-01-01

In the framework of a project aiming to improve the properties of poly(ε-caprolactone) (PCL)-based devices, we prepared novel composites and tested their in vitro biocompatibility and osteogenic capacity on human mesenchymal stromal cells (MSC) from bone marrow. We prepared two functionalized derivatives, PCL-g-MAGMA and PCL-g-DMAEA, by insertion of anhydride groups by radical grafting of maleic anhydride (MA) and glycidyl-methacrylate (GMA) molecules, and by insertion of N-(dimethylamino)ethylacrylate (DMAEA) of tertiary amines groups, respectively. In addition, in order to improve the osteoconductive properties of the materials, we also prepared the corresponding composites containing the mineral component of bone, namely hydroxyapatite (HA). Mesenchymal stromal cells (MSC) derived from bone marrow were prepared, plated onto a number of discs obtained from these functionalized derivatives and tested in terms of adhesion and vitality (by MTT test and SEM observation), and the expression of alkaline phosphatase, the early marker of osteoblastic phenotype. The biological in vitro assessment of the functionalized materials, PCL-g-MAGMA and PCL-g-DMAEA, appeared promising only in part, in particular the cells exhibited very poor adhesion to PCL-g-MAGMA. On the contrary, the related composites, PCL-g-MAGMA-HA and PCL-g-DMAEA-HA clearly showed that the addition of HA greatly ameliorated the cell-material interaction. In particular, a surprisingly increased response characterized PCL-g-MAGMA-HA, either in terms of adhesion and vitality or in terms of alkaline phosphatase activity. Altogether these studies showed that the addition of HA nanowhiskers resulted for all basic materials, in particular PCL-g-MAGMA, in improved cell adhesion and performance.

Systematic study of electron-phonon coupling to oxygen modes across the cuprates

NASA Astrophysics Data System (ADS)

Johnston, S.; Vernay, F.; Moritz, B.; Shen, Z.-X.; Nagaosa, N.; Zaanen, J.; Devereaux, T. P.

2010-08-01

The large variations in Tc across the cuprate families is one of the major unsolved puzzles in condensed matter physics and is poorly understood. Although there appears to be a great deal of universality in the cuprates, several orders of magnitude changes in Tc can be achieved through changes in the chemical composition and structure of the unit cell. In this paper we formulate a systematic examination of the variations in electron-phonon coupling to oxygen phonons in the cuprates, incorporating a number of effects arising from several aspects of chemical composition and doping across cuprate families. It is argued that the electron-phonon coupling is a very sensitive probe of the material-dependent variations in chemical structure, affecting the orbital character of the band crossing the Fermi level, the strength of local electric fields arising from structural-induced symmetry breaking, doping-dependent changes in the underlying band structure, and ionicity of the crystal governing the ability of the material to screen c -axis perturbations. Using electrostatic Ewald calculations and known experimental structural data, we establish a connection between the material’s maximal Tc at optimal doping and the strength of coupling to c -axis modes. We demonstrate that materials with the largest coupling to the out-of-phase bond-buckling (B1g) oxygen phonon branch also have the largest Tc ’s. In light of this observation we present model Tc calculations using a two-well model where phonons work in conjunction with a dominant pairing interaction, presumably due to spin fluctuations, indicating how phonons can generate sizeable enhancements to Tc despite the relatively small coupling strengths. Combined, these results can provide a natural framework for understanding the doping and material dependence of Tc across the cuprates.

Mass transfer of large molecules through collagen and collagen-silica hybrid membranes

NASA Astrophysics Data System (ADS)

Jofre-Lora, Pedro

Diabetes is a growing concern in the United States and around the world that must be addressed through new treatment options. Current standard treatment options of diabetes are limiting and have tremendous impacts on patient's lives. Emerging therapies, such as the implantation of encapsulated islets, are promising treatment options, but have not yet materialized due to unsolved problems with material properties. Hybrid silica-collagen membranes address some of these unsolved problems and are a promising material for cell encapsulation. However, the mass transfer properties of large molecules, such as insulin, TNF-alpha, IL1beta, and other important proteins in the etiology of diabetes, through these hybrid membranes are poorly characterized. In order to begin characterizing these properties, a device was constructed to accurately and efficiently measure the mass transfer of other similar large molecules, fluorescein isothiocyanate dextrans (FITC-dextran), through collagen-silica hybrid membranes. The device was used to measure diffusion coefficients of 4, 20, 40, and 150 kDa FITC-dextrans through non-silicified and silicified samples of 200 and 1000 Pa porcine skin collagen. Diffusion coefficients were found to be in the 10-7-10-6 cm2s -1 range, which is in agreement with previously published data for similar molecules through similar hydrogels. The effects of collagen stiffness, FITC-dextran molecular weight, and silicification treatment on diffusion were investigated. It was found that collagen stiffness and FITC-dextran molecular weight had a negative correlation with diffusion, whereas silicification treatment had no global impact on diffusion. The device created, and the results of this preliminary investigation, can be used to develop collagen-silica hybrid membranes as an alternative material for cell encapsulation in a forward-design manner.

Detecting ordered small molecule drug aggregates in live macrophages: a multi-parameter microscope image data acquisition and analysis strategy

PubMed Central

Rzeczycki, Phillip; Yoon, Gi Sang; Keswani, Rahul K.; Sud, Sudha; Stringer, Kathleen A.; Rosania, Gus R.

2017-01-01

Following prolonged administration, certain orally bioavailable but poorly soluble small molecule drugs are prone to precipitate out and form crystal-like drug inclusions (CLDIs) within the cells of living organisms. In this research, we present a quantitative multi-parameter imaging platform for measuring the fluorescence and polarization diattenuation signals of cells harboring intracellular CLDIs. To validate the imaging system, the FDA-approved drug clofazimine (CFZ) was used as a model compound. Our results demonstrated that a quantitative multi-parameter microscopy image analysis platform can be used to study drug sequestering macrophages, and to detect the formation of ordered molecular aggregates formed by poorly soluble small molecule drugs in animals. PMID:28270989

Detecting ordered small molecule drug aggregates in live macrophages: a multi-parameter microscope image data acquisition and analysis strategy.

PubMed

Rzeczycki, Phillip; Yoon, Gi Sang; Keswani, Rahul K; Sud, Sudha; Stringer, Kathleen A; Rosania, Gus R

2017-02-01

Following prolonged administration, certain orally bioavailable but poorly soluble small molecule drugs are prone to precipitate out and form crystal-like drug inclusions (CLDIs) within the cells of living organisms. In this research, we present a quantitative multi-parameter imaging platform for measuring the fluorescence and polarization diattenuation signals of cells harboring intracellular CLDIs. To validate the imaging system, the FDA-approved drug clofazimine (CFZ) was used as a model compound. Our results demonstrated that a quantitative multi-parameter microscopy image analysis platform can be used to study drug sequestering macrophages, and to detect the formation of ordered molecular aggregates formed by poorly soluble small molecule drugs in animals.

Evaluation of Sealing Materials and Techniques for Installing Quoin and Miter Block Backing Grout

DTIC Science & Technology

2015-11-01

being used effectively in the field. The materials currently in use have low viscosities and are typically poured behind the quoin and miter blocks in...tively in the field. The materials now used have low viscosities . They are typ- ically poured behind the quoin and miter blocks in lifts. The perimeter of...colder temperatures. Low viscosity at warmer temperatures. Hilti HIT ICE Epoxy Acrylate It is primarily a cold weather product that had poor

Chirality and orbital order in charge density waves

NASA Astrophysics Data System (ADS)

van Wezel, Jasper

2011-12-01

Helical arrangements of spins are common among magnetic materials. The first material to harbor a corkscrew pattern of charge density, on the other hand, was discovered only very recently. The nature of the order parameter is of key relevance, since rotating a magnetic vector around any propagation vector trivially yields a helical pattern. In contrast, the purely scalar charge density cannot straightforwardly support a chiral state. Here we use a Landau order parameter analysis to resolve this paradox, and show that the chiral charge order may be understood as a form of orbital ordering. We discuss the microscopic mechanism driving the transition and show it to be of a general form, thus allowing for a broad class of materials to display this novel type of orbital-ordered chiral charge density wave.

Proline-poor hydrophobic domains modulate the assembly and material properties of polymeric elastin.

PubMed

Muiznieks, Lisa D; Reichheld, Sean E; Sitarz, Eva E; Miao, Ming; Keeley, Fred W

2015-10-01

Elastin is a self-assembling extracellular matrix protein that provides elasticity to tissues. For entropic elastomers such as elastin, conformational disorder of the monomer building block, even in the polymeric form, is essential for elastomeric recoil. The highly hydrophobic monomer employs a range of strategies for maintaining disorder and flexibility within hydrophobic domains, particularly involving a minimum compositional threshold of proline and glycine residues. However, the native sequence of hydrophobic elastin domain 30 is uncharacteristically proline-poor and, as an isolated polypeptide, is susceptible to formation of amyloid-like structures comprised of stacked β-sheet. Here we investigated the biophysical and mechanical properties of multiple sets of elastin-like polypeptides designed with different numbers of proline-poor domain 30 from human or rat tropoelastins. We compared the contributions of these proline-poor hydrophobic sequences to self-assembly through characterization of phase separation, and to the tensile properties of cross-linked, polymeric materials. We demonstrate that length of hydrophobic domains and propensity to form β-structure, both affecting polypeptide chain flexibility and cross-link density, play key roles in modulating elastin mechanical properties. This study advances the understanding of elastin sequence-structure-function relationships, and provides new insights that will directly support rational approaches to the design of biomaterials with defined suites of mechanical properties. © 2015 Wiley Periodicals, Inc.

The hidden practices and experiences of healthcare practitioners dealing with fuel poverty.

PubMed

Mc Conalogue, D; Kierans, C; Moran, A

2016-06-01

Fuel poverty negatively impacts a population's health affecting life chances along the life course. Moreover, it represents a substantial inequality in the UK. Healthcare practitioners (HCPs) have a key role in identifying and supporting patients who are fuel poor. A qualitative inquiry with District Nurses and General Practitioners, to explore their understanding and experiences of dealing with patients living in fuel poverty. Participants recognize fuel poverty by observing material cues. They perceive their relationship with the patient as pivotal to recognizing the fuel poor. Practitioners' sense of responsibility for their patients' social concerns is determined by their knowledge about the link to health outcomes. The services that they sign-post to are motivated by their experience dealing with the service, or their patients' experiences of the service. Participants' reliance on temporary material cues resulted in few experiences of recognition of the fuel poor. HCPs' perceptions of patient pride and the lack of personal relationship between doctor and patient presented barriers to identifying fuel poor patients. A limitation of this study is the small sample size of nine participants. These came from two professional groups, which afforded more depth of exploration, but may limit applicability to other professionals. © The Author 2015. Published by Oxford University Press on behalf of Faculty of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Plasma-assisted microwave processing of materials

NASA Technical Reports Server (NTRS)

Barmatz, Martin (Inventor); Jackson, Henry (Inventor); Ylin, Tzu-yuan (Inventor)

1998-01-01

A microwave plasma assisted method and system for heating and joining materials. The invention uses a microwave induced plasma to controllably preheat workpiece materials that are poorly microwave absorbing. The plasma preheats the workpiece to a temperature that improves the materials' ability to absorb microwave energy. The plasma is extinguished and microwave energy is able to volumetrically heat the workpiece. Localized heating of good microwave absorbing materials is done by shielding certain parts of the workpiece and igniting the plasma in the areas not shielded. Microwave induced plasma is also used to induce self-propagating high temperature synthesis (SHS) process for the joining of materials. Preferably, a microwave induced plasma preheats the material and then microwave energy ignites the center of the material, thereby causing a high temperature spherical wave front from the center outward.

Mass transport in morphogenetic processes: A second gradient theory for volumetric growth and material remodeling

NASA Astrophysics Data System (ADS)

Ciarletta, P.; Ambrosi, D.; Maugin, G. A.

2012-03-01

In this work, we derive a novel thermo-mechanical theory for growth and remodeling of biological materials in morphogenetic processes. This second gradient hyperelastic theory is the first attempt to describe both volumetric growth and mass transport phenomena in a single-phase continuum model, where both stress- and shape-dependent growth regulations can be investigated. The diffusion of biochemical species (e.g. morphogens, growth factors, migration signals) inside the material is driven by configurational forces, enforced in the balance equations and in the set of constitutive relations. Mass transport is found to depend both on first- and on second-order material connections, possibly withstanding a chemotactic behavior with respect to diffusing molecules. We find that the driving forces of mass diffusion can be written in terms of covariant material derivatives reflecting, in a purely geometrical manner, the presence of a (first-order) torsion and a (second-order) curvature. Thermodynamical arguments show that the Eshelby stress and hyperstress tensors drive the rearrangement of the first- and second-order material inhomogeneities, respectively. In particular, an evolution law is proposed for the first-order transplant, extending a well-known result for inelastic materials. Moreover, we define the first stress-driven evolution law of the second-order transplant in function of the completely material Eshelby hyperstress. The theory is applied to two biomechanical examples, showing how an Eshelbian coupling can coordinate volumetric growth, mass transport and internal stress state, both in physiological and pathological conditions. Finally, possible applications of the proposed model are discussed for studying the unknown regulation mechanisms in morphogenetic processes, as well as for optimizing scaffold architecture in regenerative medicine and tissue engineering.

Sample-Poor Estimation of Order and Common Signal Subspace with Application to Fusion of Medical Imaging Data

PubMed Central

Levin-Schwartz, Yuri; Song, Yang; Schreier, Peter J.; Calhoun, Vince D.; Adalı, Tülay

2016-01-01

Due to their data-driven nature, multivariate methods such as canonical correlation analysis (CCA) have proven very useful for fusion of multimodal neurological data. However, being able to determine the degree of similarity between datasets and appropriate order selection are crucial to the success of such techniques. The standard methods for calculating the order of multimodal data focus only on sources with the greatest individual energy and ignore relations across datasets. Additionally, these techniques as well as the most widely-used methods for determining the degree of similarity between datasets assume sufficient sample support and are not effective in the sample-poor regime. In this paper, we propose to jointly estimate the degree of similarity between datasets and their order when few samples are present using principal component analysis and canonical correlation analysis (PCA-CCA). By considering these two problems simultaneously, we are able to minimize the assumptions placed on the data and achieve superior performance in the sample-poor regime compared to traditional techniques. We apply PCA-CCA to the pairwise combinations of functional magnetic resonance imaging (fMRI), structural magnetic resonance imaging (sMRI), and electroencephalogram (EEG) data drawn from patients with schizophrenia and healthy controls while performing an auditory oddball task. The PCA-CCA results indicate that the fMRI and sMRI datasets are the most similar, whereas the sMRI and EEG datasets share the least similarity. We also demonstrate that the degree of similarity obtained by PCA-CCA is highly predictive of the degree of significance found for components generated using CCA. PMID:27039696

Deposition and properties of cobalt- and ruthenium-based ultra-thin films

NASA Astrophysics Data System (ADS)

Henderson, Lucas Benjamin

Future copper interconnect systems will require replacement of the materials that currently comprise both the liner layer(s) and the capping layer. Ruthenium has previously been considered as a material that could function as a single material liner, however its poor ability to prevent copper diffusion makes it incompatible with liner requirements. A recently described chemical vapor deposition route to amorphous ruthenium-phosphorus alloy films could correct this problem by eliminating the grain boundaries found in pure ruthenium films. Bias-temperature stressing of capacitor structures using 5 nm ruthenium-phosphorus film as a barrier to copper diffusion and analysis of the times-to-failure at accelerated temperature and field conditions implies that ruthenium-phosphorus performs acceptably as a diffusion barrier for temperatures above 165°C. The future problems associated with the copper capping layer are primarily due to the poor adhesion between copper and the current Si-based capping layers. Cobalt, which adheres well to copper, has been widely proposed to replace the Si-based materials, but its ability to prevent copper diffusion must be improved if it is to be successfully implemented in the interconnect. Using a dual-source chemistry of dicobaltoctacarbonyl and trimethylphosphine at temperatures from 250-350°C, amorphous cobalt-phosphorus can be deposited by chemical vapor deposition. The films contain elemental cobalt and phosphorus, plus some carbon impurity, which is incorporated in the film as both graphitic and carbidic (bonded to cobalt) carbon. When deposited on copper, the adhesion between the two materials remains strong despite the presence of phosphorus and carbon at the interface, but the selectivity for growth on copper compared to silicon dioxide is poor and must be improved prior to consideration for application in interconnect systems. A single molecule precursor containing both cobalt and phosphorus atoms, tetrakis(trimethylphosphine)cobalt(0), yields cobalt-phosphorus films without any co-reactant. However, the molecule does not contain sufficient amounts of amorphizing agents to fully eliminate grain boundaries, and the resulting film is nanocrystalline.

Study on the quality of FRP fishing vessel based on improved Fishbone Chart

NASA Astrophysics Data System (ADS)

Sui, J. H.; Yu, Y. F.; Du, Q. F.; Jiang, D. W.

2018-01-01

The construction quality of FRP fishing vessels influences their production, use and industry development. In order to explore the factors that affect the construction quality of FRP fishing vessels, key factors affecting the construction quality of FRP fishing vessels are determined based on the quality problems of FRP fishing vessels constructed. The improved Fishbone Chart is used to analyze the eight factors of “human, machine, material, process, environment, inspection, design and information”. Taking the factors that affect the construction quality of FRP fishing vessels as the central target, the eight influencing factors were condensed into five aspects and a composite Fishbone Chart is drawn. The Fishbone Chart is used as the basic model, the influencing factors are sorted, screened and discriminated, and the system model convenient for construction site management and control is established. Finally, the causes of poor construction of FRP fishing vessels are analyzed and discussed, and relevant suggestions are put forward.

Corrosion and tribocorrosion behavior of Ti-B4C composite intended for orthopaedic implants.

PubMed

Toptan, F; Rego, A; Alves, A C; Guedes, A

2016-08-01

Poor wear resistance of titanium is a major concern since relative movements due to the cyclic loads in body environment cause wear between the bone and the implant material leading to detachment of the wear debris and release of metal ions due to the simultaneous action of corrosion and wear, defined as tribocorrosion. In order to increase the tribocorrosion resistance, Grade 2 Ti matrix 24vol% B4C particle reinforced composites were processed by hot pressing. Corrosion behaviour was investigated by electrochemical impedance spectroscopy and potentiodynamic polarization in 9g/L NaCl solution at body temperature. Tribocorrosion tests were performed under open circuit potential, as well as under potentiodynamic polarization using a reciprocating ball-on-plate tribometer. Results suggested that the addition of B4C particles provided lower tendency to corrosion and lower corrosion kinetics under sliding, along with significantly reduced wear loss, mainly due to the load carrying effect given by the reinforcement particles. Copyright © 2016 Elsevier Ltd. All rights reserved.

RF Guns for Generation of Polarized Electron Beams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clendenin, J.E.; Brachmann, A.; Dowell, D.H.

2005-11-09

Several accelerators, including the SLC, JLAB, Mainz, Bates/MIT, and Bonn have successfully operated for medium and high energy physics experiments using polarized electron beams generated by dc-biased guns employing GaAs photocathodes. Since these guns have all used a bias on the order of 100 kV, the longitudinal emittance of the extracted bunch is rather poor. Downstream rf bunching systems increase the transverse emittance. An rf gun with a GaAs photocathode would eliminate the need for separate rf bunchers, resulting in a simpler injection system. In addition, the thermal emittance of GaAs-type cathodes is significantly lower than for other photocathode materials.more » The environmental requirements for operating activated GaAs photocathodes cannot be met by rf guns as currently designed and operated. These requirements, including limits on vacuum and electron back bombardment, are discussed in some detail. Modifications to actual and proposed rf gun designs that would allow these requirements to be met are presented.« less

Photo-processing P3HT conjugated polymers, in solution: A new route towards ordered polymeric structures.

NASA Astrophysics Data System (ADS)

Barbosa Neto, Newton; Dutra, Marcia; Araujo, Paulo; Sampaio, Renato

Solution aggregated thin films of conjugated polymers have demonstrated to be promising materials for many applications, e.g., solar cells and field-effect transistors. There are many standard methods to generate aggregates in polymeric solution, which includes poor solvent addiction and solution temperature manipulation. Here, we demonstrate a new approach to induce aggregate formation on solution of P3HT polymer. Under light excitation with 355 nm or 532 nm pulsed laser the polymer exhibit significant changes on its UV-Vis spectrum which are most known in the literature as the formation of H-J aggregates and additional new bands associated with polaron formation. Such changes in the amorphous phase of the polymers are seen in specific conditions of solvent combinations. We show also the dependency on the excitation laser power which can be identified as a threshold to ignite the formation of the new structure. We are grateful to CNPq and CAPES for financial support.

Energy-Conversion Properties of Vapor-Liquid-Solid-Grown Silicon Wire-Array Photocathodes

NASA Astrophysics Data System (ADS)

Boettcher, Shannon W.; Spurgeon, Joshua M.; Putnam, Morgan C.; Warren, Emily L.; Turner-Evans, Daniel B.; Kelzenberg, Michael D.; Maiolo, James R.; Atwater, Harry A.; Lewis, Nathan S.

2010-01-01

Silicon wire arrays, though attractive materials for use in photovoltaics and as photocathodes for hydrogen generation, have to date exhibited poor performance. Using a copper-catalyzed, vapor-liquid-solid-growth process, SiCl4 and BCl3 were used to grow ordered arrays of crystalline p-type silicon (p-Si) microwires on p+-Si(111) substrates. When these wire arrays were used as photocathodes in contact with an aqueous methyl viologen2+/+ electrolyte, energy-conversion efficiencies of up to 3% were observed for monochromatic 808-nanometer light at fluxes comparable to solar illumination, despite an external quantum yield at short circuit of only 0.2. Internal quantum yields were at least 0.7, demonstrating that the measured photocurrents were limited by light absorption in the wire arrays, which filled only 4% of the incident optical plane in our test devices. The inherent performance of these wires thus conceptually allows the development of efficient photovoltaic and photoelectrochemical energy-conversion devices based on a radial junction platform.

Energy-conversion properties of vapor-liquid-solid-grown silicon wire-array photocathodes.

PubMed

Boettcher, Shannon W; Spurgeon, Joshua M; Putnam, Morgan C; Warren, Emily L; Turner-Evans, Daniel B; Kelzenberg, Michael D; Maiolo, James R; Atwater, Harry A; Lewis, Nathan S

2010-01-08

Silicon wire arrays, though attractive materials for use in photovoltaics and as photocathodes for hydrogen generation, have to date exhibited poor performance. Using a copper-catalyzed, vapor-liquid-solid-growth process, SiCl4 and BCl3 were used to grow ordered arrays of crystalline p-type silicon (p-Si) microwires on p+-Si(111) substrates. When these wire arrays were used as photocathodes in contact with an aqueous methyl viologen(2+/+) electrolyte, energy-conversion efficiencies of up to 3% were observed for monochromatic 808-nanometer light at fluxes comparable to solar illumination, despite an external quantum yield at short circuit of only 0.2. Internal quantum yields were at least 0.7, demonstrating that the measured photocurrents were limited by light absorption in the wire arrays, which filled only 4% of the incident optical plane in our test devices. The inherent performance of these wires thus conceptually allows the development of efficient photovoltaic and photoelectrochemical energy-conversion devices based on a radial junction platform.

3D printed plastics for beam modulation in proton therapy

NASA Astrophysics Data System (ADS)

Lindsay, C.; Kumlin, J.; Jirasek, A.; Lee, R.; Martinez, D. M.; Schaffer, P.; Hoehr, C.

2015-06-01

Two 3D printing methods, fused filament fabrication (FFF) and PolyJet™ (PJ) were investigated for suitability in clinical proton therapy (PT) energy modulation. Measurements of printing precision, printed density and mean stopping power are presented. FFF is found to be accurate to 0.1 mm, to contain a void fraction of 13% due to air pockets and to have a mean stopping power dependent on geometry. PJ was found to print accurate to 0.05 mm, with a material density and mean stopping power consistent with solid poly(methyl methacrylate) (PMMA). Both FFF and PJ were found to print significant, sporadic defects associated with sharp edges on the order of 0.2 mm. Site standard PT modulator wheels were printed using both methods. Measured depth-dose profiles with a 74 MeV beam show poor agreement between PMMA and printed FFF wheels. PJ printed wheel depth-dose agreed with PMMA within 1% of treatment dose except for a distal falloff discrepancy of 0.5 mm.

Quantifying microstructural dynamics and electrochemical activity of graphite and silicon-graphite lithium ion battery anodes

NASA Astrophysics Data System (ADS)

Pietsch, Patrick; Westhoff, Daniel; Feinauer, Julian; Eller, Jens; Marone, Federica; Stampanoni, Marco; Schmidt, Volker; Wood, Vanessa

2016-09-01

Despite numerous studies presenting advances in tomographic imaging and analysis of lithium ion batteries, graphite-based anodes have received little attention. Weak X-ray attenuation of graphite and, as a result, poor contrast between graphite and the other carbon-based components in an electrode pore space renders data analysis challenging. Here we demonstrate operando tomography of weakly attenuating electrodes during electrochemical (de)lithiation. We use propagation-based phase contrast tomography to facilitate the differentiation between weakly attenuating materials and apply digital volume correlation to capture the dynamics of the electrodes during operation. After validating that we can quantify the local electrochemical activity and microstructural changes throughout graphite electrodes, we apply our technique to graphite-silicon composite electrodes. We show that microstructural changes that occur during (de)lithiation of a pure graphite electrode are of the same order of magnitude as spatial inhomogeneities within it, while strain in composite electrodes is locally pronounced and introduces significant microstructural changes.

Tunable electrical conductivity in oriented thin films of tetrathiafulvalene-based covalent organic framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, SL; Zhang, YB; Pun, AB

2014-09-16

Despite the high charge-carrier mobility in covalent organic frameworks (COFs), the low intrinsic conductivity and poor solution processability still impose a great challenge for their applications in flexible electronics. We report the growth of oriented thin films of a tetrathiafulvalene-based COF (TTF-COF) and its tunable doping. The porous structure of the crystalline TTF-COF thin film allows the diffusion of dopants such as I-2 and tetracyanoquinodimethane (TCNQ) for redox reactions, while the closely packed 2D grid sheets facilitate the cross-layer delocalization of thus-formed TTF radical cations to generate more conductive mixed-valence TTF species, as is verified by UV-vis-NIR and electron paramagneticmore » resonance spectra. Conductivity as high as 0.28 S m(-1) is observed for the doped COF thin films, which is three orders of magnitude higher than that of the pristine film and is among the highest for COF materials.« less

Female bluethroats enhance offspring immunocompetence through extra-pair copulations.

PubMed

Johnsen, A; Andersen, V; Sunding, C; Lifjeld, J T

2000-07-20

Female birds frequently copulate with extra-pair males, but the adaptive value of this behaviour is poorly understood. Some studies have suggested that 'good genes' may be involved, where females seek to have their eggs fertilized by high-quality males without receiving any material benefits from them. Nevertheless, it remains to be shown that a genetic benefit is passed on to offspring. Here we report that nestling bluethroats, Luscinia svecica, sired by extra-pair males had a higher T-cell-mediated immune response than their maternal half-siblings raised in the same nest. The difference could not be attributed to nestling body mass, sex or hatching order, but may be an effect of paternal genotype. Extra-pair young were also more immunocompetent than their paternal half-sibs raised in the genetic father's own nest, which indicates an additional effect of maternal genotype. Our results are consistent with the idea that females engage in extra-pair copulations to obtain compatible viability genes, rather than 'good genes' per se.

The adsorption of NO, NH3, N2 on carbon surface: a density functional theory study.

PubMed

Wang, Jiayong; Yang, Mo; Deng, Debing; Qiu, Shuxia

2017-08-11

To explore the adsorption mechanism of NO, NH 3 , N 2 on a carbon surface, and the effect of basic and acidic functional groups, density functional theory was employed to investigate the interactions between these molecules and carbon surfaces. Molecular electrostatic potential, Mulliken population analyses, reduced density gradient, and Mayer bond order analyses were used to clarify the adsorption mechanism. The results indicate that van der Waals interactions are responsible for N 2 physisorption, and N 2 is the least likely to adsorb on a carbon surface. Modification of carbon materials to decorate basic or acidic functional groups could enhance the NH 3 physisorption because of hydrogen bonding or electrostatic interactions, however, NO physisorption on a carbon surface is poor. Zig-zag sites are more reactive than armchair sites when these gas molecules absorb on the edge sites of carbon surface. Graphical abstract NH 3 , N 2 , NO adsortion on carbon surface.

A change in the optical polarization associated with a gamma-ray flare in the blazar 3C 279.

PubMed

2010-02-18

It is widely accepted that strong and variable radiation detected over all accessible energy bands in a number of active galaxies arises from a relativistic, Doppler-boosted jet pointing close to our line of sight. The size of the emitting zone and the location of this region relative to the central supermassive black hole are, however, poorly known, with estimates ranging from light-hours to a light-year or more. Here we report the coincidence of a gamma (gamma)-ray flare with a dramatic change of optical polarization angle. This provides evidence for co-spatiality of optical and gamma-ray emission regions and indicates a highly ordered jet magnetic field. The results also require a non-axisymmetric structure of the emission zone, implying a curved trajectory for the emitting material within the jet, with the dissipation region located at a considerable distance from the black hole, at about 10(5) gravitational radii.

A change in the optical polarization associated with a γ-ray flare in the blazar 3C279

DOE PAGES

Abdo, A. A.; Ackermann, M.; Ajello, M.; ...

2010-02-18

It is widely accepted that strong and variable radiation detected over all accessible energy bands in a number of active galaxies arises from a relativistic, Doppler-boosted jet pointing close to our line of sight1. Furthermore, the size of the emitting zone and the location of this region relative to the central supermassive black hole are, however, poorly known, with estimates ranging from light-hours to a light-year or more. We report the coincidence of a gamma (γ)-ray flare with a dramatic change of optical polarization angle. This provides evidence for co-spatiality of optical and γ-ray emission regions and indicates a highlymore » ordered jet magnetic field. Our results also require a non-axisymmetric structure of the emission zone, implying a curved trajectory for the emitting material within the jet, with the dissipation region located at a considerable distance from the black hole, at about 105 gravitational radii.« less

Modeling the Monthly Water Balance of a First Order Coastal Forested Watershed

Treesearch

S. V. Harder; Devendra M. Amatya; T. J. Callahan; Carl C. Trettin

2006-01-01

A study has been conducted to evaluate a spreadsheet-based conceptual Thornthwaite monthly water balance model and the process-based DRAINMOD model for their reliability in predicting monthly water budgets of a poorly drained, first order forested watershed at the Santee Experimental Forest located along the Lower Coastal Plain of South Carolina. Measured precipitation...

Enhancing Students' HOTS in Laboratory Educational Activity by Using Concept Map as an Alternative Assessment Tool

ERIC Educational Resources Information Center

Ghani, I. B. A.; Ibrahim, N. H.; Yahaya, N. A.; Surif, J.

2017-01-01

Educational transformation in the 21st century demands in-depth knowledge and understanding in order to promote the development of higher-order thinking skills (HOTS). However, the most commonly reported problem with respect to developing a knowledge of chemistry is poor mastery of basic concepts. Chemistry laboratory educational activities are…

Structural origin underlying poor glass forming ability of Al metallic glass

NASA Astrophysics Data System (ADS)

Li, F.; Liu, X. J.; Hou, H. Y.; Chen, G.; Chen, G. L.

2011-07-01

We performed molecular dynamics simulations to study the glass formation and local atomic structure of rapidly quenched Al. Both potential energy and structural parameters indicate that the glass transition temperature of amorphous Al is as low as 300 K, which may lead to the poor thermal stability of the amorphous Al as it is prone to crystallize even at room temperature. Voronoi polyhedra analysis reveals that the most popular polyhedron is the deformed body-centered cubic (bcc) cluster characterized by the index < 0, 3, 6, 4 > in the amorphous Al, while the icosahedron with the index < 0, 0, 12, 0 > is always predominant in bulk metallic glass formers with excellent glass forming ability (GFA). Moreover, these deformed-bcc short-range orders can make up medium-range orders via the linkage of vertex-, edge-, face-, intercrossed-shared atoms, which are believed to more easily transform into face-centered cubic (fcc) Al nanocrystal compared with the icosahedral clusters in terms of the symmetrical similarity between bcc and fcc structures. This finding could unveil the structural origin of poor GFA of Al-based alloys.

Saving the child to save the nation: poverty, whiteness and childhood in the Cape Colony, c.1870-1895.

PubMed

Duff, S E

2011-01-01

Children were central to efforts to eradicate white impoverishment in the Cape Colony in the late nineteenth century. The education and training of poor, white children were believed to be the most effective ways of breaking cycles of poverty, and of ensuring continuing white control over the Cape's resources. Yet a closer reading of the evidence presented to the 1894 Labour Commission and the committee appointed to investigate the Destitute Children Relief Bill suggests that this interest in poor, white children also stemmed from concerns about the children themselves. Destitute white children - both male and female - were described, frequently, as representing a threat to the social, moral, and even economic order, and this view of poor white children shaped official responses to white poverty. This concern for white children reflected not solely their status as 'children' - that they represented the colony's future, were fairly malleable, and could be more easily 'reached' by projects and schemes to eradicate white poverty - but also their problematic class position in a colonial racial order that sought their reform, direction and education into acceptable productive citizens.

Taking action on the social determinants of health: improving health access for the urban poor in Mongolia

PubMed Central

2012-01-01

Introduction In recent years, the country of Mongolia (population 2.8 million) has experienced rapid social changes associated with economic growth, persisting socio-economic inequities and internal migration. In order to improve health access for the urban poor, the Ministry of Health developed a "Reaching Every District" strategy (RED strategy) to deliver an integrated package of key health and social services. The aim of this article is to present findings of an assessment of the implementation of the RED strategy, and, on the basis of this assessment, articulate lessons learned for equitable urban health planning. Methods Principal methods for data collection and analysis included literature review, barrier analysis of health access and in-depth interviews and group discussions with health managers and providers. Findings The main barriers to health access for the urban poor relate to interacting effects of poverty, unhealthy daily living environments, social vulnerability and isolation. Implementation of the RED strategy has resulted in increased health access for the urban poor, as demonstrated by health staff having reached new clients with immunization, family planning and ante-natal care services, and increased civil registrations which enable social service provision. Organizational effects have included improved partnerships for health and increased motivation of the health workforce. Important lessons learned from the early implementation of the RED strategy include the need to form strong partnerships among stakeholders at each level of the health system and in the community, as well as the need to develop a specific financing strategy to address the needs of the very poor. The diverse social context for health in an urban poor setting calls for a decentralized planning and partnership strategy, but with central level commitment towards policy guidance and financing of pro-poor urban health strategies. Conclusions Lessons from Mongolia mirror other international studies which point to the need to measure and take action on the social determinants of health at the local area level in order to adequately reduce persistent inequities in health care access for the urban poor. PMID:22429615

High performance superconducting devices enabled by three dimensionally ordered nanodots and/or nanorods

DOEpatents

Goyal, Amit

2013-09-17

Novel articles and methods to fabricate same with self-assembled nanodots and/or nanorods of a single or multicomponent material within another single or multicomponent material for use in electrical, electronic, magnetic, electromagnetic and electrooptical devices is disclosed. Self-assembled nanodots and/or nanorods are ordered arrays wherein ordering occurs due to strain minimization during growth of the materials. A simple method to accomplish this when depositing in-situ films is also disclosed. Device applications of resulting materials are in areas of superconductivity, photovoltaics, ferroelectrics, magnetoresistance, high density storage, solid state lighting, non-volatile memory, photoluminescence, thermoelectrics and in quantum dot lasers.

High performance electrical, magnetic, electromagnetic and electrooptical devices enabled by three dimensionally ordered nanodots and nanorods

DOEpatents

Goyal, Amit , Kang; Sukill, [Knoxville, TN

2012-02-21

Novel articles and methods to fabricate same with self-assembled nanodots and/or nanorods of a single or multicomponent material within another single or multicomponent material for use in electrical, electronic, magnetic, electromagnetic and electrooptical devices is disclosed. Self-assembled nanodots and/or nanorods are ordered arrays wherein ordering occurs due to strain minimization during growth of the materials. A simple method to accomplish this when depositing in-situ films is also disclosed. Device applications of resulting materials are in areas of superconductivity, photovoltaics, ferroelectrics, magnetoresistance, high density storage, solid state lighting, non-volatile memory, photoluminescence, thermoelectrics and in quantum dot lasers.

Fluidized Bed Sputtering for Particle and Powder Metallization

DTIC Science & Technology

2013-04-01

Introduction Small particles are often added to material systems to modify mechanical, dielectric, optical, or other properties . However, the particle...the poor mechanical properties of the wax degrade the bulk mechanical properties of the composite material . Thin metal coatings on the catalyst...to create precisely tailored optical properties . Alternating layers of ceramic and metal thin films can be designed to create optical filters that

Through-the-Wall Small Weapon Detection Based on Polarimetric Radar Techniques

DTIC Science & Technology

2009-12-01

waves can penetrate through clothing (textile materials ), they have very poor penetration properties through many common construction materials (such...including the continuous metallic barrel ). Unless specified otherwise, the mesh has a resolution (cell size) of 2 mm. The wood dielectric constant...almost perpendicularly to the barrel ). Figure 2. Estimating the tilt angle of a cylindrical metallic rod of 1 m length

Spectroscopic investigation of the chemical and electronic properties of chalcogenide materials for thin-film optoelectronic devices

NASA Astrophysics Data System (ADS)

Horsley, Kimberly Anne

Chalcogen-based materials are at the forefront of technologies for sustainable energy production. This progress has come only from decades of research, and further investigation is needed to continue improvement of these materials. For this dissertation, a number of chalcogenide systems were studied, which have applications in optoelectronic devices, such as LEDs and Photovoltaics. The systems studied include Cu(In,Ga)Se2 (CIGSe) and CuInSe 2 (CISe) thin-film absorbers, CdTe-based photovoltaic structures, and CdTe-ZnO nanocomposite materials. For each project, a sample set was prepared through collaboration with outside institutions, and a suite of spectroscopy techniques was employed to answer specific questions about the system. These techniques enabled the investigation of the chemical and electronic structure of the materials, both at the surface and towards the bulk. CdS/Cu(In,Ga)Se2 thin-films produced from the roll-to-roll, ambient pressure, Nanosolar industrial line were studied. While record-breaking efficiency cells are usually prepared in high-vacuum (HV) or ultra-high vacuum (UHV) environments, these samples demonstrate competitive mass-production efficiency without the high-cost deposition environment. We found relatively low levels of C contaminants, limited Na and Se oxidation, and a S-Se intermixing at the CdS/CIGSe interface. The surface band gap compared closely to previously investigated CIGSe thin-films deposited under vacuum, illustrating that roll-to-roll processing is a promising and less-expensive alternative for solar cell production. An alternative deposition process for CuInSe2 was also studied, in collaboration with the University of Luxembourg. CuInSe2 absorbers were prepared with varying Cu content and surface treatments to investigate the potential to produce an absorber with a Cu-rich bulk and Cu-poor surface. This is desired to combine the bulk characteristics of reduced defects and larger grains in Cu-rich films, while maintaining a wide surface band gap, as seen in Cu-poor films. A novel absorber was prepared Cu-rich with a final In-Se treatment to produce a Cu-poor surface, and compared directly to Cu-poor and Cu-rich produced samples. Despite reduced Cu at the surface, the novel absorber was found to have a surface band gap similar to that of traditional, Cu-poor grown absorbers. Furthermore, estimation of the near-surface bulk band gap suggests a narrowing of the band gap away from the surface, similar to highly efficient, Cu-poor grown absorbers. Long-term degradation is another concern facing solar cells, as heat and moistures stress can result in reduced efficiencies over time. The interface of the back contact material and absorber layer in (Au/Cu)/CdTe/CdS thin-film structures from the University of Toledo were investigated after a variety of accelerated stress treatments with the aim of further understanding the chemical and/or electronic degradation of this interface. Sulfur migration to the back contact was observed, along with the formation of Au-S and Cu-S bonds. A correlation between heat stress under illumination and the formation of Cu-Cl bonds was also found. Nanocomposite materials hold promise as a next-generation photovoltaic material and for use in LED devices, due in part to the unique ability to tune the absorption edge of the film by adjusting the semiconductor particle size, and the prospective for long-range charge-carrier (exciton) transport through the wide band gap matrix material. Thin films of CdTe were sputter deposited onto ZnO substrates at the University of Arizona and studied before and after a short, high temperature annealing to further understand the effects of annealing on the CdTe/ZnO interface. A clumping of the CdTe layer and the formation of Cd- and Te-oxides was observed using surface microscopy and photoelectron spectroscopy techniques. These findings help to evaluate post-deposition annealing as a treatment to adjust the final crystallinity and optoelectronic properties of these films. Through publication and/or discussion with collaborators, each project presented in this dissertation contributed to the understanding of the chemical and electronic properties of the material surface, near-surface bulk, and/or interfaces formed. The information gained on these unique chalcogenide materials will assist in designing more efficient and successful optoelectronic devices for the next generation of solar cells and LEDs.

Well-ordered mesoporous Fe2O3/C composites as high performance anode materials for sodium-ion batteries.

PubMed

Li, Mei; Ma, Chao; Zhu, Qian-Cheng; Xu, Shu-Mao; Wei, Xiao; Wu, Yong-Min; Tang, Wei-Ping; Wang, Kai-Xue; Chen, Jie-Sheng

2017-04-11

Sodium-ion batteries have attracted considerable attention in recent years. In order to promote the practical application of sodium-ion batteries, the electrochemical performances, such as specific capacity, reversibility, and rate capability of the anode materials, should be further improved. In this work, a Fe 2 O 3 /C composite with a well-ordered mesoporous structure is prepared via a facile co-impregnation method by using mesoporous silica SBA-15 as a hard template. When used as an anode material for sodium-ion batteries, the well-ordered mesoporous structure ensures fast mass transport kinetics. The presence of nano-sized Fe 2 O 3 particles confined within the carbon walls significantly enhances the specific capacity of the composite. The carbon walls in the composite act not only as an active material contributing to the specific capacity, but also as a conductive matrix improving the cycling stability of Fe 2 O 3 nanoparticles. As a result, the well-ordered mesoporous Fe 2 O 3 /C composite exhibits high specific capacity, excellent cycleability, and high rate capability. It is proposed that this simple co-impregnation method is applicable for the preparation of well-ordered mesoporous transition oxide/carbon composite electrode materials for high performance sodium-ion and lithium-ion batteries.

TACOM LCMC Sustainment Engineering Risk Assessment (SERA) Overview

DTIC Science & Technology

2012-07-26

Technical Data with Limited Availability 2.0 Hazardous Materials 1.0 Shelf Life Sensitivity 4.0 Persistent Back Order 8-Month 3.0 Top 10% CWT 3.0 No...Materials Shelf Life Sensitivity Persistent Back Order 8-Month Top 10% CWT No Demand in past 3 years Top 10% Closed Maintenance Work Order for

Spectral evidence for the mineralogy of high-albedo soils and dust on Mars

NASA Technical Reports Server (NTRS)

Singer, R. B.

1982-01-01

Laboratory spectroscopic observations are presented which further constrain the mineralogy and origin of the high albedo Martian soils and dust, and suggest that nontronite is not a major component of Martian soils, although the presence of other iron-poor clays cannot be excluded on the basis of current observational data. Because the best of the known spectral analogs for the high albedo Martian material is a type of palagonite from Hawaii, it is thought that ferric iron is likely to occur in poorly defined Martian crystallographic sites producing X-ray amorphous weathering products of mafic volcanic glass. These materials form slowly, under semiarid conditions, at ambient temperatures. Since the amorphous Hawaiian soils exist metastably for thousands of years, their Martian analogs may be expected to survive even longer under the present cold and dry climatic conditions.

The single-crystal multinary compound Cu2ZnSnS4 as an environmentally friendly high-performance thermoelectric material

NASA Astrophysics Data System (ADS)

Nagaoka, Akira; Masuda, Taizo; Yasui, Shintaro; Taniyama, Tomoyasu; Nose, Yoshitaro

2018-05-01

We investigated the thermoelectric properties of high-quality p-type Cu2ZnSnS4 single crystals. This material showed two advantages: low thermal conductivity because of lattice scattering caused by the easily formed Cu/Zn disordered structure, and high conductivity because of high doping from changes to the composition. All samples showed a thermal conductivity of 3.0 W m‑1 K‑1 at 300 K, and the Cu-poor sample showed a conductivity of 7.5 S/cm at 300 K because of the high density of shallow-acceptor Cu vacancies. The figure of merit of the Cu-poor Cu2ZnSnS4 reached 0.2 at 400 K, which is 1.4–45 times higher than those of related compounds.

Detritus utilization by Mytilus edulis

NASA Astrophysics Data System (ADS)

Williams, Phil

1981-06-01

Feeding expriments showed that salt marsh vascular plant detritus is a poor food for Mytilus edulis. In laboratory experiment tissue weight of mussels increased slightly when Spartina foliosa and Salicornia virginica detritus was added to background seawater rich in organic matter. However, mussels lost weight when detritus was added to background seawater with a lower organic matter content. Aged and unaged plant material were equally poor in food value for M. edulis. Mussels in the Tijuana Estuary grew substantially during the period of the laboratory experiments.

FeOx‐Based Materials for Electrochemical Energy Storage

PubMed Central

Ma, Jingyi; Guo, Xiaotian; Yan, Yan; Xue, Huaiguo

2018-01-01

Abstract Iron oxides (FeOx), such as Fe2O3 and Fe3O4 materials, have attracted much attention because of their rich abundance, low cost, and environmental friendliness. However, FeOx, which is similar to most transition metal oxides, possesses a poor rate capability and cycling life. Thus, FeOx‐based materials consisting of FeOx, carbon, and metal‐based materials have been widely explored. This article mainly discusses FeOx‐based materials (Fe2O3 and Fe3O4) for electrochemical energy storage applications, including supercapacitors and rechargeable batteries (e.g., lithium‐ion batteries and sodium‐ion batteries). Furthermore, future perspectives and challenges of FeOx‐based materials for electrochemical energy storage are briefly discussed.

Advances in molecular dynamics simulation of ultra-precision machining of hard and brittle materials

NASA Astrophysics Data System (ADS)

Guo, Xiaoguang; Li, Qiang; Liu, Tao; Kang, Renke; Jin, Zhuji; Guo, Dongming

2017-03-01

Hard and brittle materials, such as silicon, SiC, and optical glasses, are widely used in aerospace, military, integrated circuit, and other fields because of their excellent physical and chemical properties. However, these materials display poor machinability because of their hard and brittle properties. Damages such as surface micro-crack and subsurface damage often occur during machining of hard and brittle materials. Ultra-precision machining is widely used in processing hard and brittle materials to obtain nanoscale machining quality. However, the theoretical mechanism underlying this method remains unclear. This paper provides a review of present research on the molecular dynamics simulation of ultra-precision machining of hard and brittle materials. The future trends in this field are also discussed.

Thermal Characterization of Fe3O4 Nanoparticles Formed from Poorly Crystalline Siderite

NASA Technical Reports Server (NTRS)

Lauer, H. V., Jr.; Ming, D. W.; Golden, D. C.

2005-01-01

Increasing interest in environmental geochemistry has led to the recognition that crystals with sizes in the nanometer range (e.g., colloids and nanoscale precipitates) and poorly crystalline compounds (e.g., ferrihydrites) may comprise the majority of reactive mineral surface area near the Earth s surface. When the diameters of individual particles are in the range of 100 nm or less, the surface energy contribution to the free energy modifies phase stability. This results in stabilization of polymorphs not normally encountered in the macrocrystal domain. These phases potentially have very different surface-site geometries, adsorptive properties, and growth mechanisms, and exhibit size-dependent kinetic behavior. Thus nanophases dramatically modify the physical and chemical properties of soils and sediments. In a more general sense, the characteristics of nanocrystals are of intense technological interest because small particle size confers novel chemical, optical, and electronic properties. Thus, nanocrystalline materials are finding applications as catalytic substrates, gas phase separation materials, and even more importantly in the field of medicine. This is an opportune time for mineral physicists working on nanocrystalline materials to develop collaborative efforts with materials scientists, chemists, and others working on nanophase materials of technological interest (e.g., for magnetic memories). Our objective in this study was to synthesize submicron (<200 nm) magnetite and to study their thermal and particle size properties.

IMPROVDENT: improving dentures for patient benefit. A crossover randomised clinical trial comparing impression materials for complete dentures.

PubMed

Gray, Janine C; Navarro-Coy, Nuria; Pavitt, Sue H; Hulme, Claire; Godfrey, Mary; Craddock, Helen L; Brunton, Paul A; Brown, Sarah; Dillon, Sean; Dukanovic, Gillian; Fernandez, Catherine; Wright, Jonathan; Collier, Howard; Swithenbank, Shirley; Lee, Carol; Hyde, T Paul

2012-08-31

According to the UK Adult Dental Health Survey (2009) 15% of adults aged 65-74, 30% aged 75-84 and 47% aged >85 years are edentulous and require complete dentures. Patients' quality of life and nutrition status are affected by poor dentures. The quality of the dental impression is the most important issue for improving the fit and comfort of new dentures. There is paucity of RCT evidence for which impression material is best for complete dentures construction. This study aims to compare two impression materials for effectiveness and cost effectiveness. IMPROVDENT is a double-blind crossover trial comparing the use of alginate and silicone, two commonly used denture impression materials, in terms of patient preference and cost-effectiveness. Eighty five edentulous patients will be recruited and provided with two sets of dentures, similar in all aspects except for the impression material used (alginate or silicone). Patients will try both sets of dentures for a two-week period, unadjusted, to become accustomed to the feel of the new dentures (habituation period). Patients will then wear each set of dentures for a period of 8 weeks (in random order) during which time the dentures will be adjusted for optimum comfort. Finally, patients will be given both sets of dentures for a further two weeks to wear whichever denture they prefer (confirmation period).Patients will be asked about quality of life and to rate dentures on function and comfort at the end of each trial period and asked which set they prefer at the end of the habituation period (unadjusted denture preference) and confirmation period (adjusted denture preference). A health economic evaluation will estimate incremental cost-effectiveness ratios of producing dentures from the two materials. A qualitative study will investigate the impact of dentures on behaviour and quality of life. IMPROVDENT is funded by NIHR RfPB (PB-PG-0408-16300). This trial aims to provide evidence on the costs and quality of dentures cast from two different commonly used impression materials; the intention is to significantly impact on the quality of denture production within NHS dentistry. ISRCTN Register: ISRCTN01528038 UKCRN Portfolio ID: 8305.

Good phonetic errors in poor spellers are associated with right-handedness and possible weak utilisation of visuospatial abilities.

PubMed

Eglinton, Elizabeth; Annett, Marian

2008-06-01

Poor spellers in normal schools, who were not poor readers, were studied for handedness, visuospatial and other cognitive abilities in order to explore contrasts between poor spellers with and without good phonology. It was predicted by the right shift (RS) theory of handedness and cerebral dominance that those with good phonology would have strong bias to dextrality and relative weakness of the right hemisphere, while those without good phonology would have reduced bias to dextrality and relative weakness of the left hemisphere. Poor spellers with good phonetic equivalent spelling errors (GFEs) included fewer left-handers (2.4%) than poor spellers without GFEs (24.4%). Differences for hand skill were as predicted. Tests of visuospatial processing found no differences between the groups in levels of ability, but there was a marked difference in pattern of correlations between visuospatial test scores and homophonic word discrimination. Whereas good spellers (GS) and poor spellers without GFEs showed positive correlations between word discrimination and visuospatial ability, there were no significant correlations for poor spellers with GFEs. The differences for handedness and possibly for the utilisation of visuospatial skills suggest that surface dyslexics differ from phonological dyslexics in cerebral specialisation and perhaps in the quality of inter-hemispheric relations.

Impact Compaction of a Granular Material

NASA Astrophysics Data System (ADS)

Fenton, Gregg; Asay, Blaine; Todd, Steve; Grady, Dennis

2017-06-01

The dynamic behavior of granular materials has importance to a variety of engineering applications. Although, the mechanical behavior of granular materials have been studied extensively for several decades, the dynamic behavior of these materials remains poorly understood. High-quality experimental data are needed to improve our general understanding of granular material compaction physics. This paper describes how an instrumented plunger impact system can be used to measure the compaction process for granular materials at high and controlled strain rates and subsequently used for computational modelling. The experimental technique relies on a gas-gun driven plunger system to generate a compaction wave through a volume of granular material. This volume of material has been redundantly instrumented along the bed length to track the progression of the compaction wave, and the piston displacement is measured with Photon Doppler Velocimetry (PDV). Using the gathered experimental data along with the initial material tap density, a granular material equation of state can be determined.

Materials Refining for Structural Elements From Lunar Resources

NASA Astrophysics Data System (ADS)

Landis, Geoffrey A.

1998-01-01

Use of in situ resources for construction on the Moon will require manufacturing structural materials out of lunar resources. Many materials that are currently used for aerospace and construction require materials that have low availability on the Moon. For example, graphite fiber, SiC fiber, and artificial fiber composites (such as Kevlar, Spectra, etc.) are used as advanced lightweight structural materials on Earth, but the low availability of C on the Moon makes these poor choices. Likewise the polymers used as the matrix for these composites, epoxy or polyester, also suffer from the low availability of C. Bulk paving and construction materials such as cement or concrete suffer from the low availability of water on the Moon, while asphalt, a common paving material on Earth, suffers from the low availability of C.

Design of Functional Materials based on Liquid Crystalline Droplets.

PubMed

Miller, Daniel S; Wang, Xiaoguang; Abbott, Nicholas L

2014-01-14

This brief perspective focuses on recent advances in the design of functional soft materials that are based on confinement of low molecular weight liquid crystals (LCs) within micrometer-sized droplets. While the ordering of LCs within micrometer-sized domains has been explored extensively in polymer-dispersed LC materials, recent studies performed with LC domains with precisely defined size and interfacial chemistry have unmasked observations of confinement-induced ordering of LCs that do not follow previously reported theoretical predictions. These new findings, which are enabled in part by advances in the preparation of LCs encapsulated in polymeric shells, are opening up new opportunities for the design of soft responsive materials based on surface-induced ordering transitions. These materials are also providing new insights into the self-assembly of biomolecular and colloidal species at defects formed by LCs confined to micrometer-sized domains. The studies presented in this perspective serve additionally to highlight gaps in knowledge regarding the ordering of LCs in confined systems.

Generating Bulk-Scale Ordered Optical Materials Using Shear-Assembly in Viscoelastic Media.

PubMed

Finlayson, Chris E; Baumberg, Jeremy J

2017-06-22

We review recent advances in the generation of photonics materials over large areas and volumes, using the paradigm of shear-induced ordering of composite polymer nanoparticles. The hard-core/soft-shell design of these particles produces quasi-solid "gum-like" media, with a viscoelastic ensemble response to applied shear, in marked contrast to the behavior seen in colloidal and granular systems. Applying an oscillatory shearing method to sub-micron spherical nanoparticles gives elastomeric photonic crystals (or "polymer opals") with intense tunable structural color. The further engineering of this shear-ordering using a controllable "roll-to-roll" process known as Bending Induced Oscillatory Shear (BIOS), together with the interchangeable nature of the base composite particles, opens potentially transformative possibilities for mass manufacture of nano-ordered materials, including advances in optical materials, photonics, and metamaterials/plasmonics.

Generating Bulk-Scale Ordered Optical Materials Using Shear-Assembly in Viscoelastic Media

PubMed Central

Finlayson, Chris E.; Baumberg, Jeremy J.

2017-01-01

We review recent advances in the generation of photonics materials over large areas and volumes, using the paradigm of shear-induced ordering of composite polymer nanoparticles. The hard-core/soft-shell design of these particles produces quasi-solid “gum-like” media, with a viscoelastic ensemble response to applied shear, in marked contrast to the behavior seen in colloidal and granular systems. Applying an oscillatory shearing method to sub-micron spherical nanoparticles gives elastomeric photonic crystals (or “polymer opals”) with intense tunable structural color. The further engineering of this shear-ordering using a controllable “roll-to-roll” process known as Bending Induced Oscillatory Shear (BIOS), together with the interchangeable nature of the base composite particles, opens potentially transformative possibilities for mass manufacture of nano-ordered materials, including advances in optical materials, photonics, and metamaterials/plasmonics. PMID:28773044

Assessing the application of tooth cementum annulation relative to macroscopic aging techniques in an archeological sample.

PubMed

Gauthier, J; Schutkowski, H

2013-02-01

The analysis of human skeletal remains is frequently impeded by the lack of adequately preserved morphological markers on which to base age estimation, particularly in archeological contexts. Therefore, histological methods such as tooth cementum annulation analysis can be useful for extracting reliable age estimates from poorly preserved skeletons, if they produce results corresponding to morphologically based, multifactorial assessments. In order to test this presumption, this study compares tooth cementum annulation (TCA) with macroscopic age estimation results incorporating the Brooks-Suchey pubic symphysis and the Buckberry-Chamberlain revised auricular surface methods, as well as Brothwell's guidelines for analyzing dental attrition. Undecalcified, polished, and unstained transverse thin sections viewed using standard light microscopy, with decentered phase contrast microscopy in cases of poorly delineated cementum annulations, were used for TCA counts. Age estimates were applied independently on the late medieval archeological Box Lane cemetery assemblage from Pontefract, England, to analyze their measure of correspondence and to assess whether data produced by a single histological technique are comparable to information pooled from multiple morphological age markers. Spearman's rank correlation tests resulted in a significant association between TCA and morphological age estimates. Further studies using larger samples of known age material would help to improve our understanding of TCA age estimation performance relative to macroscopic age assessment as well as continued refinement and standardization of cementum sectioning, which is suggested to impact annulation visibility. Copyright © 2012 Elsevier GmbH. All rights reserved.

Laser Shock Peening on Zr-based Bulk Metallic Glass and Its Effect on Plasticity: Experiment and Modeling

NASA Astrophysics Data System (ADS)

Cao, Yunfeng; Xie, Xie; Antonaglia, James; Winiarski, Bartlomiej; Wang, Gongyao; Shin, Yung C.; Withers, Philip J.; Dahmen, Karin A.; Liaw, Peter K.

2015-05-01

The Zr-based bulk metallic glasses (BMGs) are a new family of attractive materials with good glass-forming ability and excellent mechanical properties, such as high strength and good wear resistance, which make them candidates for structural and biomedical materials. Although the mechanical behavior of BMGs has been widely investigated, their deformation mechanisms are still poorly understood. In particular, their poor ductility significantly impedes their industrial application. In the present work, we show that the ductility of Zr-based BMGs with nearly zero plasticity is improved by a laser shock peening technique. Moreover, we map the distribution of laser-induced residual stresses via the micro-slot cutting method, and then predict them using a three-dimensional finite-element method coupled with a confined plasma model. Reasonable agreement is achieved between the experimental and modeling results. The analyses of serrated flows reveal plentiful and useful information of the underlying deformation process. Our work provides an easy and effective way to extend the ductility of intrinsically-brittle BMGs, opening up wider applications of these materials.

Morphology-dependent optical absorption and conduction properties of photoelectrochemical photocatalysts for H2 production: A case study

NASA Astrophysics Data System (ADS)

Huda, Muhammad N.; Turner, John A.

2010-06-01

Efficient photoelectrochemical H2 production by solar irradiation depends not only on the photocatalyst's band gap and its band-edge positions but also on the detailed electronic nature of the bands, such as the localization or delocalization of the band edges and their orbital characteristics. These determine the carrier transport properties, reactivity, light absorption strength, etc. and significantly impact the material's efficiency as a photoconverter. The localization or delocalization of the band edges may arise either due to the orbital nature of the bands or the structural morphology of the material. A recent experimental report on a photocatalyst based on s /p orbitals showed very poor performance for H2 production despite the delocalized nature of the s /p bands as compared to the d-bands of transition metal oxides. It is then important to examine whether this poor performance is inherent to these materials or rather arises from some experimental limitations. A theoretical analysis by first-principle methods is well suited to shed light on this question.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whittles, Thomas J.; Veal, Tim D.; Savory, Christopher N.

The earth-abundant material CuSbS 2 (CAS) has shown good optical properties as a photovoltaic solar absorber material, but has seen relatively poor solar cell performance. To investigate the reason for this anomaly, the core levels of the constituent elements, surface contaminants, ionization potential, and valence-band spectra are studied by X-ray photoemission spectroscopy. The ionization potential and electron affinity for this material (4.98 and 3.43 eV) are lower than those for other common absorbers, including CuInxGa (1-x)Se 2 (CIGS). Experimentally corroborated density functional theory (DFT) calculations show that the valence band maximum is raised by the lone pair electrons from themore » antimony cations contributing additional states when compared with indium or gallium cations in CIGS. The resulting conduction band misalignment with CdS is a reason for the poor performance of cells incorporating a CAS/CdS heterojunction, supporting the idea that using a cell design analogous to CIGS is unhelpful. These findings underline the critical importance of considering the electronic structure when selecting cell architectures that optimize open-circuit voltages and cell efficiencies.« less

Laser shock peening on Zr-based bulk metallic glass and its effect on plasticity: Experiment and modeling

DOE PAGES

Cao, Yunfeng; Xie, Xie; Antonaglia, James; ...

2015-05-20

The Zr-based bulk metallic glasses (BMGs) are a new family of attractive materials with good glass-forming ability and excellent mechanical properties, such as high strength and excellent wear resistance, which make them candidates for structural and biomedical materials. Although the mechanical behavior of BMGs has been widely investigated, their deformation mechanisms are still poorly understood. In particular, their poor ductility significantly impedes their industrial application. In the present work, we show that the ductility of Zr-based BMGs with nearly zero plasticity is improved by a laser shock peening technique. Moreover, we map the distribution of laser-induced residual stresses via themore » micro-slot cutting method, and then predict them using a three dimensional finite-element method coupled with a confined plasma model. Reasonable agreement is achieved between the experimental and modeling results. The analysis of serrated flow reveals plentiful and useful information of the underlying deformation process. As a result, our work provides an easy and effective way to extend the ductility of intrinsically-brittle BMGs, opening up wider applications of these materials.« less

Effects of increase glacier discharge on phytoplankton bloom dynamics and pelagic geochemistry in a high Arctic fjord

NASA Astrophysics Data System (ADS)

Calleja, Maria Ll.; Kerhervé, P.; Bourgeois, S.; Kędra, M.; Leynaert, A.; Devred, E.; Babin, M.; Morata, N.

2017-12-01

Arctic fjords experience extremely pronounced seasonal variability and spatial heterogeneity associated with changes in ice cover, glacial retreat and the intrusion of continental shelf's adjacent water masses. Global warming intensifies natural environmental variability on these important systems, yet the regional and global effects of these processes are still poorly understood. In the present study, we examine seasonal and spatial variability in Kongsfjorden, on the western coast of Spitsbergen, Svalbard. We report hydrological, biological, and biogeochemical data collected during spring, summer, and fall 2012. Our results show a strong phytoplankton bloom with the highest chlorophyll a (Chla) levels ever reported in this area, peaking 15.5 μg/L during late May and completely dominated by large diatoms at the inner fjord, that may sustain both pelagic and benthic production under weakly stratified conditions at the glacier front. A progressively stronger stratification of the water column during summer and fall was shaped by the intrusion of warm Atlantic water (T > 3 °C and Sal > 34.65) into the fjord at around 100 m depth, and by turbid freshwater plumes (T < 1 °C and Sal < 34.65) at the surface due to glacier meltwater input. Biopolymeric carbon fractions and isotopic signatures of the particulate organic material (POM) revealed very fresh and labile material produced during the spring bloom (13C enriched, with values up to -22.7‰ at the highest Chl a peak, and high in carbohydrates and proteins content - up to 167 and 148 μg/L, respectively-), and a clear and strong continental signature of the POM present during late summer and fall (13C depleted, with values averaging -26.5‰, and high in lipid content - up to 92 μg/L-) when freshwater melting is accentuated. Our data evidence the importance of combining both physical (i.e. water mass dominance) and geochemical (i.e. characteristics of material released by glacier runoff) data in order to understand the timing, intensity and characteristics of the phytoplankton bloom in Kongsfjorden, a continuously changing system due to sustained warming. In a scenario where glacial retreat is predicted to increase the impacts of meltwater discharge and associated delivery of organic and inorganic material to the surrounding waters, special attention is required in order to predict the consequences for Arctic fjords and adjacent shelf ecosystems.

A highly ordered mesostructured material containing regularly distributed phenols: preparation and characterization at a molecular level through ultra-fast magic angle spinning proton NMR spectroscopy.

PubMed

Roussey, Arthur; Gajan, David; Maishal, Tarun K; Mukerjee, Anhurada; Veyre, Laurent; Lesage, Anne; Emsley, Lyndon; Copéret, Christophe; Thieuleux, Chloé

2011-03-14

Highly ordered organic-inorganic mesostructured material containing regularly distributed phenols is synthesized by combining a direct synthesis of the functional material and a protection-deprotection strategy and characterized at a molecular level through ultra-fast magic angle spinning proton NMR spectroscopy.

Temporal auditory aspects in children with poor school performance and associated factors.

PubMed

Rezende, Bárbara Antunes; Lemos, Stela Maris Aguiar; Medeiros, Adriane Mesquita de

2016-01-01

To investigate the auditory temporal aspects in children with poor school performance aged 7-12 years and their association with behavioral aspects, health perception, school and health profiles, and sociodemographic factors. This is an observational, analytical, transversal study including 89 children with poor school performance aged 7-12 years enrolled in the municipal public schools of a municipality in Minas Gerais state, participants of Specialized Educational Assistance. The first stage of the study was conducted with the subjects' parents aiming to collect information on sociodemographic aspects, health profile, and educational records. In addition, the parents responded to the Strengths and Difficulties Questionnaire (SDQ). The second stage was conducted with the children in order to investigate their health self-perception and analyze the auditory assessment, which consisted of meatoscopy, Transient Otoacoustic Emissions, and tests that evaluated the aspects of simple auditory temporal ordering and auditory temporal resolution. Tests assessing the temporal aspects of auditory temporal processing were considered as response variables, and the explanatory variables were grouped for univariate and multivariate logistic regression analyses. The level of significance was set at 5%. Significant statistical correlation was found between the auditory temporal aspects and the variables age, gender, presence of repetition, and health self-perception. Children with poor school performance presented changes in the auditory temporal aspects. The temporal abilities assessed suggest association with different factors such as maturational process, health self-perception, and school records.

Parent-Adolescent Sexual and Reproductive Health Communication Is Very Limited and Associated with Adolescent Poor Behavioral Beliefs and Subjective Norms: Evidence from a Community Based Cross-Sectional Study in Eastern Ethiopia.

PubMed

Dessie, Yadeta; Berhane, Yemane; Worku, Alemayehu

2015-01-01

While parent-adolescent sexual and reproductive health (SRH) communication is one potential source of SRH information for adolescents, it appears to be inadequately practiced in Ethiopia. This study was designed to investigate the factors that limit or improve parent-adolescent SRH communication in Harar, Eastern Ethiopia. A community based cross-sectional study was done on 4,559 adolescents of age 13-18. SRH communication was measured using a nine-item scale whose response ranged from "not at all" to "always." Summated composite score ranging from 0-36 was generated; higher score indicates high SRH communication. A median value of the composite score was 4 out of the possible 36 with an Interquartile Range (IQR) of 7. Respondents were ranked as very poor, poor and satisfactory communicators based on 33rd and 67th percentiles values. Generalized ordered logit model was applied to investigate the factors associated with SRH communication. Results showed that the adolescents who were more likely to practice poor-very poor/very poor SRH communication were those who had poor behavioral beliefs on and poor subjective norms of communicating sexual issues with parents and those who perceived their parents' reproductive health (RH) knowledge as poor. Nonetheless, the probability of poor-very poor/very poor SRH communication was less with high adolescent-parent communication quality, television co-viewing and discussions, and self-disclosure. Curtailing the adolescents' underlying poor beliefs and norms, and improving adolescent-parent communication quality, self-disclosure, and television co-viewing and discussions are essential to engage the parents in sexual and reproductive health education of the adolescents.

Parent-Adolescent Sexual and Reproductive Health Communication Is Very Limited and Associated with Adolescent Poor Behavioral Beliefs and Subjective Norms: Evidence from a Community Based Cross-Sectional Study in Eastern Ethiopia

PubMed Central

2015-01-01

Introduction While parent-adolescent sexual and reproductive health (SRH) communication is one potential source of SRH information for adolescents, it appears to be inadequately practiced in Ethiopia. This study was designed to investigate the factors that limit or improve parent-adolescent SRH communication in Harar, Eastern Ethiopia. Methods A community based cross-sectional study was done on 4,559 adolescents of age 13–18. SRH communication was measured using a nine-item scale whose response ranged from “not at all” to “always.” Summated composite score ranging from 0–36 was generated; higher score indicates high SRH communication. A median value of the composite score was 4 out of the possible 36 with an Interquartile Range (IQR) of 7. Respondents were ranked as very poor, poor and satisfactory communicators based on 33rd and 67th percentiles values. Generalized ordered logit model was applied to investigate the factors associated with SRH communication. Results Results showed that the adolescents who were more likely to practice poor-very poor/very poor SRH communication were those who had poor behavioral beliefs on and poor subjective norms of communicating sexual issues with parents and those who perceived their parents’ reproductive health (RH) knowledge as poor. Nonetheless, the probability of poor-very poor/very poor SRH communication was less with high adolescent-parent communication quality, television co-viewing and discussions, and self-disclosure. Conclusions Curtailing the adolescents’ underlying poor beliefs and norms, and improving adolescent-parent communication quality, self-disclosure, and television co-viewing and discussions are essential to engage the parents in sexual and reproductive health education of the adolescents. PMID:26167860

Non-motorized winter recreation impacts to snowmelt erosion, Tronsen Basin, Eastern Cascades, Washington.

PubMed

Eagleston, Holly; Rubin, Charles

2013-01-01

Many recreation impact studies have focused on summer activities, but the environmental impact of winter recreation is poorly characterized. This study characterizes the impact of snowshoe/cross-country ski compaction and snowmelt erosion on trails. Trail cross-sectional profiles were measured before and after the winter season to map changes in erosion due to winter recreation. Compacted snow on the trail was 30 % more dense than snowpack off the trail before spring melt out. Snow stayed on the trail 7 days longer. Soil and organic material was transported after spring snowmelt with -9.5 ± 2.4 cm(2) total erosion occurring on the trail transects and -3.8 ± 2.4 cm(2) total erosion occurring on the control transect (P = 0.046). More material was transported on the trail than on the control, 12.9± 2.4 versus 6.0 ± 2.4 cm(2) (P = 0.055), however, deposition levels remained similar on the trail and on the control. Snow compaction from snowshoers and cross-country skiers intensified erosion. Trail gradient was found to be significantly correlated to net changes in material on the trail (R (2) = 0.89, ρ = -0.98, P = 0.005). This study provides a baseline, showing that non-motorized winter recreation does impact soil erosion rates but more studies are needed. Trail managers should consider mitigation such as water bars, culverts and avoiding building trails with steep gradients, in order to reduce loss of soils on trails and subsequent sedimentation of streams.

Non-motorized Winter Recreation Impacts to Snowmelt Erosion, Tronsen Basin, Eastern Cascades, Washington

NASA Astrophysics Data System (ADS)

Eagleston, Holly; Rubin, Charles

2013-01-01

Many recreation impact studies have focused on summer activities, but the environmental impact of winter recreation is poorly characterized. This study characterizes the impact of snowshoe/cross-country ski compaction and snowmelt erosion on trails. Trail cross-sectional profiles were measured before and after the winter season to map changes in erosion due to winter recreation. Compacted snow on the trail was 30 % more dense than snowpack off the trail before spring melt out. Snow stayed on the trail 7 days longer. Soil and organic material was transported after spring snowmelt with -9.5 ± 2.4 cm2 total erosion occurring on the trail transects and -3.8 ± 2.4 cm2 total erosion occurring on the control transect ( P = 0.046). More material was transported on the trail than on the control, 12.9± 2.4 versus 6.0 ± 2.4 cm2 ( P = 0.055), however, deposition levels remained similar on the trail and on the control. Snow compaction from snowshoers and cross-country skiers intensified erosion. Trail gradient was found to be significantly correlated to net changes in material on the trail ( R 2 = 0.89, ρ = -0.98, P = 0.005). This study provides a baseline, showing that non-motorized winter recreation does impact soil erosion rates but more studies are needed. Trail managers should consider mitigation such as water bars, culverts and avoiding building trails with steep gradients, in order to reduce loss of soils on trails and subsequent sedimentation of streams.

Meteoroid Impact Ejecta Detection by Nanosatellites for Asteroid Surface Characterization

NASA Astrophysics Data System (ADS)

Lee, N.; Close, S.; Goel, A.

2015-12-01

Asteroids are constantly bombarded by much smaller meteoroids at extremely high speeds, which results in erosion of the material on the asteroid surface. Some of this material is vaporized and ionized, forming a plasma that is ejected into the environment around the asteroid where it can be detected by a constellation of closely orbiting nanosatellites. We present a concept to leverage this natural phenomenon and to analyze this excavated material using low-power plasma sensors on nanosatellites in order to determine the composition of the asteroid surface. This concept would enable a constellation of nanosatellites to provide useful data complementing existing techniques such as spectroscopy, which require larger and more power-hungry sensors. Possible mission architectures include precursor exploratory missions using nanosatellites to survey and identify asteroid candidates worthy of further study by a large spacecraft, or simultaneous exploration by a nanosatellite constellation with a larger parent spacecraft to decrease the time required to cover the entire asteroid surface. The use of meteoroid impact plasma to analyze the surface composition of asteroids will not only produce measurements that have not been previously obtained, including the molecular composition of the surface, but will also yield a better measurement of the meteoroid flux in the vicinity of the asteroid. Current meteoroid models are poorly constrained beyond the orbit of Mars, due to scarcity of data. If this technology is used to survey asteroids in the main belt, it will offer a dramatic increase in the availability of meteoroid flux measurements in deep space, identifying previously unknown meteoroid streams and providing additional data to support models of solar system dust dynamics.

Development of an electrostatic propulsion engine using sub-micron powders as the reaction mass

NASA Technical Reports Server (NTRS)

Herbert, F.; Kendall, K. R.

1991-01-01

Asteroid sample return missions would benefit from development of an improved rocket engine. Chemical rockets achieve their large thrust with high mass consumption rate (dm/dt) but low exhaust velocity; therefore, a large fraction of their total mass is fuel. Present day ion thrusters are characterized by high exhaust velocity, but low dm/dt; thus, they are inherently low thrust devices. However, their high exhausy velocity is poorly matched to typical mission requirements and therefore, wastes energy. A better match would be intermediate between the two forms of propulsion. This could be achieved by electrostatically accelerating solid powder grains, raising the possibility that interplanetary material could be processed to use as reaction mass. An experiment to study the charging properties of sub-micron sized powder grains is described. If a suitable material can be identified, then it could be used as the reaction mass in an electrostatic propulsion engine. The experiment employs a time of flight measurement to determine the exhaust velocity (v) of various negatively charged powder grains that were charged and accelerated in a simple device. The purpose is to determine the charge to mass ratio that can be sustained for various substances. In order to be competitive with present day ion thrusters, a specific impulse (v/g) of 3000 to 5000 seconds is required. Preliminary results are presented. More speculatively, there are some mission profiles that would benefit from collection of reaction mass at the remote asteroid site. Experiments that examine the generation of sub-micron clusters by electrostatic self-disruption of geologically derived material are planned.

Solid-State Thin-Film Supercapacitors with Ultrafast Charge/Discharge Based on N-Doped-Carbon-Tubes/Au-Nanoparticles-Doped-MnO2 Nanocomposites.

PubMed

Lv, Qiying; Wang, Shang; Sun, Hongyu; Luo, Jun; Xiao, Jian; Xiao, JunWu; Xiao, Fei; Wang, Shuai

2016-01-13

Although carbonaceous materials possess long cycle stability and high power density, their low-energy density greatly limits their applications. On the contrary, metal oxides are promising pseudocapacitive electrode materials for supercapacitors due to their high-energy density. Nevertheless, poor electrical conductivity of metal oxides constitutes a primary challenge that significantly limits their energy storage capacity. Here, an advanced integrated electrode for high-performance pseudocapacitors has been designed by growing N-doped-carbon-tubes/Au-nanoparticles-doped-MnO2 (NCTs/ANPDM) nanocomposite on carbon fabric. The excellent electrical conductivity and well-ordered tunnels of NCTs together with Au nanoparticles of the electrode cause low internal resistance, good ionic contact, and thus enhance redox reactions for high specific capacitance of pure MnO2 in aqueous electrolyte, even at high scan rates. A prototype solid-state thin-film symmetric supercapacitor (SSC) device based on NCTs/ANPDM exhibits large energy density (51 Wh/kg) and superior cycling performance (93% after 5000 cycles). In addition, the asymmetric supercapacitor (ASC) device assembled from NCTs/ANPDM and Fe2O3 nanorods demonstrates ultrafast charge/discharge (10 V/s), which is among the best reported for solid-state thin-film supercapacitors with both electrodes made of metal oxide electroactive materials. Moreover, its superior charge/discharge behavior is comparable to electrical double layer type supercapacitors. The ASC device also shows superior cycling performance (97% after 5000 cycles). The NCTs/ANPDM nanomaterial demonstrates great potential as a power source for energy storage devices.

Ordered porous mesostructured materials from nanoparticle-block copolymer self-assembly

DOEpatents

Warren, Scott; Wiesner, Ulrich; DiSalvo, Jr., Francis J

2013-10-29

The invention provides mesostructured materials and methods of preparing mesostructured materials including metal-rich mesostructured nanoparticle-block copolymer hybrids, porous metal-nonmetal nanocomposite mesostructures, and ordered metal mesostructures with uniform pores. The nanoparticles can be metal, metal alloy, metal mixture, intermetallic, metal-carbon, metal-ceramic, semiconductor-carbon, semiconductor-ceramic, insulator-carbon or insulator-ceramic nanoparticles, or combinations thereof. A block copolymer/ligand-stabilized nanoparticle solution is cast, resulting in the formation of a metal-rich (or semiconductor-rich or insulator-rich) mesostructured nanoparticle-block copolymer hybrid. The hybrid is heated to an elevated temperature, resulting in the formation of an ordered porous nanocomposite mesostructure. A nonmetal component (e.g., carbon or ceramic) is then removed to produce an ordered mesostructure with ordered and large uniform pores.

Development of an All-Metal Thick Film Cost Effective Metallization System for Solar Cells

NASA Technical Reports Server (NTRS)

Ross, B.

1980-01-01

Materials including copper powders, silver-fluoride, and silicon wafers were procured and copper pastes were prepared. Electrodes made with copper pastes were analyzed and compared with the raw materials. A needle-like structure was observed on the electroded solar cells, and was identified as eutectic copper-silicon by electron probe X-ray spectroscopy. The existence of this phase was thought to benefit electrical and metallurgical properties of the contact. Subsequently electrodes made from new material were also shown to contain this phase while simultaneously having poor adhesion.

The Obsessive-Compulsive Inventory-Revised (OCI-R): psychometric properties of the Korean version and the order, gender, and cultural effects.

PubMed

Woo, Choong-Wan; Kwon, Seok-Man; Lim, Young-Jin; Shin, Min-Sup

2010-09-01

In this study, the psychometric properties of the Korean version of the OCI-R and the effects of order, gender, and culture on the inventory were examined in a nonclinical and in a clinical sample comprised of 702 college students and 91 patients with OCD. As a result, the original six-factor model is supported by the confirmatory factor analysis. The internal consistency, test-retest reliability, and the convergent and divergent validity of the OCI-R total and its subscales were good. Additionally, the receiver operating characteristic analyses showed that the OCI-R is an effective screening tool for OCD. For the negative results, the internal consistency of the neutralizing subscale was poor, and the hoarding and ordering subscale failed to distinguish patients with OCD from college students. Further, the divergent validity of the obsessing subscale appeared to be poor. A minor order effect on the OCI-R total score was observed-the decrease of the score when administered after another OCD symptom measure. No gender effects were found, whereas the cultural differences were found in some of the subscales. (c) 2010 Elsevier Ltd. All rights reserved.

A laboratory evaluation of modified asphalt : final report.

DOT National Transportation Integrated Search

1981-01-01

Quality aggregate availability in southern Louisiana has reached an alarmingly low level, while naturally occurring materials (sands) have been ignored due to their poor structural properties. Recent research reported by Chem-Crete Corporation indica...

Improved ceramic heat exchange material

NASA Technical Reports Server (NTRS)

Mccollister, H. L.

1977-01-01

Improved corrosion resistant ceramic materials that are suitable for use as regenerative heat exchangers for vehicular gas turbines is reported. Two glass-ceramic materials, C-144 and C-145, have superior durability towards sulfuric acid and sodium sulfate compared to lithium aluminosilicate (LAS) Corning heat exchange material 9455. Material C-144 is a leached LAS material whose major crystalline phase is silica keatite plus mullite, and C-145 is a LAS keatite solid solution (S.S.) material. In comparison to material 9455, material C-144 is two orders of magnitude better in dimensional stability to sulfuric acid at 300 C, and one order of magnitude better in stability to sodium sulfate at 1000 C. Material C-145 is initially two times better in stability to sulfuric acid, and about one order of magnitude better in stability to sodium sulfate. Both C-144 and C-145 have less than 300 ppm delta L/L thermal expansion from ambient to 1000 C, and good dimensional stability of less than approximately 100 ppm delta L/L after exposure to 1000 C for 100 hours. The glass-ceramic fabrication process produced a hexagonal honeycomb matrix having an 85% open frontal area, 50 micrometer wall thickness, and less than 5% porosity.

Method and Apparatus of Implementing a Magnetic Shield Flux Sweeper

NASA Technical Reports Server (NTRS)

Sadleir, John E. (Inventor)

2018-01-01

The present invention relates to a method and apparatus of protecting magnetically sensitive devices with a shield, including: a non-superconducting metal or lower transition temperature (T.sub.c) material compared to a higher transition temperature material, disposed in a magnetic field; means for creating a spatially varying order parameter's |.PSI.(r,T)|.sup.2 in a non-superconducting metal or a lower transition temperature material; wherein a spatially varying order parameter is created by a proximity effect, such that the non-superconducting metal or the lower transition temperature material becomes superconductive as a temperature is lowered, creating a flux-free Meissner state at a center thereof, in order to sweep magnetic flux lines to the periphery.

Quick Reaction Evaluation of Materials and Processes. Delivery Order 0011: Engineering Properties, Fatigue, and Crack Growth Data on SCS-6/Ti-6Al-4V Titanium Matrix Composite (16 Ply) Panels

DTIC Science & Technology

2009-05-01

tabs were bonded to the specimen using a TIG welding process to ensure adhesion of the tabs throughout the experiment. The shear specimens and the...AFRL-RX-WP-TR-2010-4175 QUICK REACTION EVALUATION OF MATERIALS AND PROCESSES Delivery Order 0011: Engineering Properties, Fatigue, and Crack...From - To) May 2009 Final 03 April 2006 – 29 May 2009 4. TITLE AND SUBTITLE QUICK REACTION EVALUATION OF MATERIALS AND PROCESSES Delivery Order

Readability, content, and quality of online patient education materials on preeclampsia.

PubMed

Lange, Elizabeth M S; Shah, Anuj M; Braithwaite, Brian A; You, Whitney B; Wong, Cynthia A; Grobman, William A; Toledo, Paloma

2015-01-01

The objective of this study was to evaluate the readability, content, and quality of patient education materials addressing preeclampsia. Websites of U.S. obstetrics and gynecology residency programs were searched for patient education materials. Readability, content, and quality were assessed. A one-sample t-test was used to evaluate mean readability level compared with the recommended 6th grade reading level. Mean readability levels were higher using all indices (p < 0.001). Content was variable with good website understandability, but poor actionability. The mean readability was above the recommended 6th grade reading level. The content, readability, and actionability of preeclampsia patient education materials should be improved.

United States Cybersecurity Strategy, Policy, and Organization: Poorly Postured to Cope with a Post-9/11 Security Environment?

DTIC Science & Technology

2012-12-14

maintain order and to deliver minimum essential public services; 3) The private sector to ensure the orderly functioning of the economy and the...the private sector’s capability to ensure the orderly functioning of the economy and delivery of essential services 5 Have a negative effect on the... economy through the cascading disruption of other critical infrastructure and key resources 6 Undermine the public’s morale and confidence in our

Indicators of Economic Status and Social Capital in South African Townships: What Do They Reveal about the Material and Social Conditions in Families of Poor Children?

ERIC Educational Resources Information Center

Barbarin, Oscar A.; Khomo, Ngokoana

1997-01-01

Employed a method for assessing material well-being and social resources using a set of observable indicators such as adequacy of food, quality of housing, financial assets, consumer goods, and social resources. Identified two dimensions, consumption and social/financial capital, which when used to assign SES were predictive of a family's ability…

The Effects of Modality and Multimedia Comprehension on the Performance of Students with Varied Multimedia Comprehension Abilities when Exposed to High Complexity, Self-Paced Multimedia Instructional Materials

ERIC Educational Resources Information Center

Al-Abbasi, Daniah

2012-01-01

Poor multimedia comprehenders suffer from a decreased ability in comprehending complex textual and pictorial materials (Maki & Maki, 2002). This deficit will lead to an overloaded working memory and consequently decreased performance (Carretti, Borella, Cornoldi, & De Beni, 2009). The purpose of this research study was to examine the effects of…

Imaging the Hydrogen Absorption Dynamics of Individual Grains in Polycrystalline Palladium Thin Films in 3D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yau, Allison; Harder, Ross J.; Kanan, Matthew W.

Defects such as dislocations and grain boundaries often control the properties of polycrystalline materials. In nanocrystalline materials, investigating this structure-function relationship while preserving the sample remains challenging because of the short length scales and buried interfaces involved. Here we use Bragg coherent diffractive imaging to investigate the role of structural inhomogeneity on the hydriding phase transformation dynamics of individual Pd grains in polycrystalline films in three-dimensional detail. In contrast to previous reports on single- and polycrystalline nanoparticles, we observe no evidence of a hydrogen-rich surface layer and consequently no size dependence in the hydriding phase transformation pressure over a 125-325more » nm size range. We do observe interesting grain boundary dynamics, including reversible rotations of grain lattices while the material remains in the hydrogen-poor phase. The mobility of the grain boundaries, combined with the lack of a hydrogen-rich surface layer, suggests that the grain boundaries are acting as fast diffusion sites for the hydrogen atoms. Such hydrogen-enhanced plasticity in the hydrogen poor phase provides insight into the switch from the size-dependent behavior of single-crystal nanoparticles to the lower transformation pressures of polycrystalline materials and may play a role in hydrogen embrittlement.« less

New developments in understanding the r-process from observations of metal-poor stars

NASA Astrophysics Data System (ADS)

Frebel, Anna

2015-04-01

In their atmospheres, old metal-poor Galactic stars retain detailed information about the chemical composition of the interstellar medium at the time of their birth. Extracting such stellar abundances enables us to reconstruct the beginning of the chemical evolution shortly after the Big Bang. About 5% of metal-poor stars with [Fe/H] < - 2 . 5 display in their spectrum a strong enhancement of neutron-capture elements associated with the rapid (r-) nucleosynthesis process that is responsible for the production of the heaviest elements in the Universe. This fortuity provides a unique opportunity of bringing together astrophysics and nuclear physics because these objects act as ``cosmic lab'' for both fields of study. The so-called r-process stars are thought to have formed from material enriched in heavy neutron-capture elements that were created during an r-process event in a previous generation supernova. It appears that the few stars known with this rare chemical signature all follow the scaled solar r-process pattern (for the heaviest elements with 56 <= Z <= 90 that is). This suggests that the r-process is universal - a surprising empirical finding and a solid result that can not be obtained from any laboratory on earth. While much research has been devoted to establishing this pattern, little attention has been given to the overall level of enhancement. New results will be presented on the full extent of r-process element enrichment as observed in metal-poor stars. The challenge lies in determining how the r-process material in the earliest gas clouds was mixed and diluted. Assuming individual r-process events to have contributed the observed r-process elements. We provide empirical estimates on the amount of r-process material produced. This should become a crucial constraint for theoretical nuclear physics models of heavy element nucleosynthesis.

Responses of alkaline phosphatase activity to phosphorus stress in Daphnia magna.

PubMed

McCarthy, S D S; Rafferty, S P; Frost, P C

2010-01-15

We examined how alkaline phosphatase (AP) activity within the bodies and in the materials released by the crustacean Daphnia magna responds to variable algal food phosphorus (P)-content. We found that Daphnia eating P-poor food (C:P approximately 700) had significantly higher AP activity in their bodies on a mass-specific basis compared with individuals eating P-rich food (C:P approximately 100). This dietary P effect on AP activity was not altered by Daphnia starvation but was partially related to differences in the P concentration of animal body homogenates. By contrast, poor P-nutrition of Daphnia lowered AP activity in released materials compared with that measured from their P-sufficient conspecifics. Moreover, AP activity in Daphnia release was lowest in animals consuming P-poor food for longer time periods. Our results support the hypothesis that AP activity increases inside P-limited Daphnia as a mechanism to increase P-acquisition and retention from ingested algae in these nutritionally stressed animals. The lower level of AP activity present in the water of P-deprived animals could reflect a change from largely free to membrane-bound AP isotypes in the digestive tracts of P-starved animals or a decrease in the shedding of membrane-anchored AP from their intestinal lining. These results supplement accumulating evidence that P-poor algal food reduces the dietary mineral P available to Daphnia. In addition, animal body AP activity measurements, with some refinement, may prove useful as an in situ indicator of P-stress in aquatic consumers.

High throughput parallel backside contacting and periodic texturing for high-efficiency solar cells

DOEpatents

Daniel, Claus; Blue, Craig A.; Ott, Ronald D.

2014-08-19

Disclosed are configurations of long-range ordered features of solar cell materials, and methods for forming same. Some features include electrical access openings through a backing layer to a photovoltaic material in the solar cell. Some features include textured features disposed adjacent a surface of a solar cell material. Typically the long-range ordered features are formed by ablating the solar cell material with a laser interference pattern from at least two laser beams.

Courses of Action to Optimize Heavy Bearings Cages

NASA Astrophysics Data System (ADS)

Szekely, V. G.

2016-11-01

The global expansion in the industrial, economically and technological context determines the need to develop products, technologies, processes and methods which ensure increased performance, lower manufacturing costs and synchronization of the main costs reported to the elementary values which correspond to utilization”. The development trend of the heavy bearing industry and the wide use of bearings determines the necessity of choosing the most appropriate material for a given application in order to meet the cumulative requirements of durability, reliability, strength, etc. Evaluation of commonly known or new materials represents a fundamental criterion, in order to choose the materials based on the cost, machinability and the technological process. In order to ensure the most effective basis for the decision, regarding the heavy bearing cage, in the first stage the functions of the product are established and in a further step a comparative analysis of the materials is made in order to establish the best materials which satisfy the product functions. The decision for selecting the most appropriate material is based largely on the overlapping of the material costs and manufacturing process during which the half-finished material becomes a finished product. The study is orientated towards a creative approach, especially towards innovation and reengineering by using specific techniques and methods applied in inventics. The main target is to find new efficient and reliable constructive and/or technological solutions which are consistent with the concept of sustainable development.

Layered/Pancake-like Ejecta on Ceres: Inferring the Composition and Mechanical Properties of the Cerean Surface through Modeling of Ejecta Emplacement

NASA Astrophysics Data System (ADS)

Hughson, K.; Russell, C. T.; Schmidt, B. E.; Chilton, H.; Scully, J. E. C.; Sizemore, H. G.; Byrne, S.; Platz, T.; Raymond, C. A.

2017-12-01

During the Survey, High Altitude Mapping Orbit, and Low Altitude Mapping Orbit phases of the primary mission Dawn's Framing Camera observed a multitude of globally distributed lobate deposits. These flows were broadly interpreted as either similar to ice-cored/ice-cemented flows (Type 1 flows) on Earth and Mars, long run-out terrestrial or martian landslides (Type 2 flows), or highly mobile fluidized ejecta-like deposits (Type 3 flows) (Buczckowski et al., 2016; Schmidt et al., 2017). The Type 3 flows are morphologically similar to layered/pancake ejecta found on Mars and Ganymede where they are thought to be caused by impacts into ground ice rich substrates (Mouginis-Mark, 1979; Boyce et al., 2010). We assess the effects of target material strength, sliding friction, and vapor entrainment on the production of these features by comparing the ejecta mobility (EM: the ratio of the radius of the ejecta blanket to the radius of the parent crater) values for all Type 3 cerean flows to a ballistic/kinematic sliding model similar to the one developed by Weiss et al. (2014) to model EM for impacts into a variety of ground ice rich substrates of differing volatile content on Mars. Initial results suggest that, in order for these features to form, the cerean surface requires a large coefficient of sliding friction (>0.1), and that significant amounts of water be vaporized during impact. However, the model does not tightly constrain the strength of the target material (best-fit values range from granite-like to unconsolidated-sand-like). These results are consistent with a largely dry, rough, and thin surface layer underlain by material rich in pore-filling ground ice, even at low latitudes. Additionally, before the Fall Meeting we will attempt to constrain the thickness of the ice-poor surface layer. This will be done through a combined analysis of model results and morphometric parameters of individual Type 3 flows. Future implementation of this model will further incorporate compositional and geophysical knowledge attained from Dawn in order to better constrain the strength of the cerean surface.

Influence of fiber degradation and concentration of fermentable sugars on simultaneous saccharification and fermentation of high-solids spruce slurry to ethanol.

PubMed

Hoyer, Kerstin; Galbe, Mats; Zacchi, Guido

2013-10-08

Saccharification and fermentation of pretreated lignocellulosic materials, such as spruce, should be performed at high solids contents in order to reduce the cost of the produced bioethanol. However, this has been shown to result in reduced ethanol yields or a complete lack of ethanol production. Previous studies have shown inconsistent results when prehydrolysis is performed at a higher temperature prior to the simultaneous saccharification and fermentation (SSF) of steam-pretreated lignocellulosic materials. In some cases, a significant increase in overall ethanol yield was reported, while in others, a slight decrease in ethanol yield was observed. In order to investigate the influence of prehydrolysis on high-solids SSF of steam-pretreated spruce slurry, in the present study, the presence of fibers and inhibitors, degree of fiber degradation and initial fermentable sugar concentration has been studied. SSF of whole steam-pretreated spruce slurry at a solids content of 13.7% water-insoluble solids (WIS) resulted in a very low overall ethanol yield, mostly due to poor fermentation. The yeast was, however, able to ferment the washed slurry and the liquid fraction of the pretreated slurry. Performing prehydrolysis at 48°C for 22 hours prior to SSF of the whole pretreated slurry increased the overall ethanol yield from 3.9 to 62.1%. The initial concentration of fermentable sugars in SSF could not explain the increase in ethanol yield in SSF with prehydrolysis. Although the viscosity of the material did not appear to decrease significantly during prehydrolysis, the degradation of the fibers prior to the addition of the yeast had a positive effect on ethanol yield when using whole steam-pretreated spruce slurry. The results of the present study suggest that the increase in ethanol yield from SSF when performing prehydrolysis is a result of fiber degradation rather than a decrease in viscosity. The increased concentration of fermentable sugars at the beginning of the fermentation phase in SSF following prehydrolysis did not affect the overall ethanol yield in the present study.

Effectiveness of interventions to reduce ordering of thyroid function tests: a systematic review.

PubMed

Zhelev, Zhivko; Abbott, Rebecca; Rogers, Morwenna; Fleming, Simon; Patterson, Anthea; Hamilton, William Trevor; Heaton, Janet; Thompson Coon, Jo; Vaidya, Bijay; Hyde, Christopher

2016-06-03

To evaluate the effectiveness of behaviour changing interventions targeting ordering of thyroid function tests. Systematic review. MEDLINE, EMBASE and the Cochrane Database up to May 2015. We included studies evaluating the effectiveness of behaviour change interventions aiming to reduce ordering of thyroid function tests. Randomised controlled trials (RCTs), non-randomised controlled studies and before and after studies were included. There were no language restrictions. 2 reviewers independently screened all records identified by the electronic searches and reviewed the full text of any deemed potentially relevant. Study details were extracted from the included papers and their methodological quality assessed independently using a validated tool. Disagreements were resolved through discussion and arbitration by a third reviewer. Meta-analysis was not used. 27 studies (28 papers) were included. They evaluated a range of interventions including guidelines/protocols, changes to funding policy, education, decision aids, reminders and audit/feedback; often intervention types were combined. The most common outcome measured was the rate of test ordering, but the effect on appropriateness, test ordering patterns and cost were also measured. 4 studies were RCTs. The majority of the studies were of poor or moderate methodological quality. The interventions were variable and poorly reported. Only 4 studies reported unsuccessful interventions but there was no clear pattern to link effect and intervention type or other characteristics. The results suggest that behaviour change interventions are effective particularly in reducing the volume of thyroid function tests. However, due to the poor methodological quality and reporting of the studies, the likely presence of publication bias and the questionable relevance of some interventions to current day practice, we are unable to draw strong conclusions or recommend the implementation of specific intervention types. Further research is thus justified. CRD42014006192. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Effectiveness of interventions to reduce ordering of thyroid function tests: a systematic review

PubMed Central

Abbott, Rebecca; Rogers, Morwenna; Fleming, Simon; Patterson, Anthea; Hamilton, William Trevor; Heaton, Janet; Vaidya, Bijay; Hyde, Christopher

2016-01-01

Objectives To evaluate the effectiveness of behaviour changing interventions targeting ordering of thyroid function tests. Design Systematic review. Data sources MEDLINE, EMBASE and the Cochrane Database up to May 2015. Eligibility criteria for selecting studies We included studies evaluating the effectiveness of behaviour change interventions aiming to reduce ordering of thyroid function tests. Randomised controlled trials (RCTs), non-randomised controlled studies and before and after studies were included. There were no language restrictions. Study appraisal and synthesis methods 2 reviewers independently screened all records identified by the electronic searches and reviewed the full text of any deemed potentially relevant. Study details were extracted from the included papers and their methodological quality assessed independently using a validated tool. Disagreements were resolved through discussion and arbitration by a third reviewer. Meta-analysis was not used. Results 27 studies (28 papers) were included. They evaluated a range of interventions including guidelines/protocols, changes to funding policy, education, decision aids, reminders and audit/feedback; often intervention types were combined. The most common outcome measured was the rate of test ordering, but the effect on appropriateness, test ordering patterns and cost were also measured. 4 studies were RCTs. The majority of the studies were of poor or moderate methodological quality. The interventions were variable and poorly reported. Only 4 studies reported unsuccessful interventions but there was no clear pattern to link effect and intervention type or other characteristics. Conclusions The results suggest that behaviour change interventions are effective particularly in reducing the volume of thyroid function tests. However, due to the poor methodological quality and reporting of the studies, the likely presence of publication bias and the questionable relevance of some interventions to current day practice, we are unable to draw strong conclusions or recommend the implementation of specific intervention types. Further research is thus justified. Trial registration number CRD42014006192. PMID:27259523

Using Polarized Spectroscopy to Investigate Order in Thin-Films of Ionic Self-Assembled Materials Based on Azo-Dyes

PubMed Central

Ahmad, Mariam; Andersen, Frederik; Brend Bech, Ári; Bendixen, H. Krestian L.; Nawrocki, Patrick R.; Bloch, Anders J.; Bora, Ilkay; Bukhari, Tahreem A.; Bærentsen, Nicolai V.; Carstensen, Jens; Chima, Smeeah; Colberg, Helene; Dahm, Rasmus T.; Daniels, Joshua A.; Dinckan, Nermin; El Idrissi, Mohamed; Erlandsen, Ricci; Førster, Marc; Ghauri, Yasmin; Gold, Mikkel; Hansen, Andreas; Hansen, Kenn; Helmsøe-Zinck, Mathias; Henriksen, Mathias; Hoffmann, Sophus V.; Hyllested, Louise O. H.; Jensen, Casper; Kallenbach, Amalie S.; Kaur, Kirandip; Khan, Suheb R.; Kjær, Emil T. S.; Kristiansen, Bjørn; Langvad, Sylvester; Lund, Philip M.; Munk, Chastine F.; Møller, Theis; Nehme, Ola M. Z.; Nejrup, Mathilde Rove; Nexø, Louise; Nielsen, Simon Skødt Holm; Niemeier, Nicolai; Nikolajsen, Lasse V.; Nøhr, Peter C. T.; Skaarup Ovesen, Jacob; Paustian, Lucas; Pedersen, Adam S.; Petersen, Mathias K.; Poulsen, Camilla M.; Praeger-Jahnsen, Louis; Qureshi, L. Sonia; Schiermacher, Louise S.; Simris, Martin B.; Smith, Gorm; Smith, Heidi N.; Sonne, Alexander K.; Zenulovic, Marko R.; Winther Sørensen, Alma; Vogt, Emil; Væring, Andreas; Westermann, Jonas; Özcan, Sevin B.

2018-01-01

Three series of ionic self-assembled materials based on anionic azo-dyes and cationic benzalkonium surfactants were synthesized and thin films were prepared by spin-casting. These thin films appear isotropic when investigated with polarized optical microscopy, although they are highly anisotropic. Here, three series of homologous materials were studied to rationalize this observation. Investigating thin films of ordered molecular materials relies to a large extent on advanced experimental methods and large research infrastructure. A statement that in particular is true for thin films with nanoscopic order, where X-ray reflectometry, X-ray and neutron scattering, electron microscopy and atom force microscopy (AFM) has to be used to elucidate film morphology and the underlying molecular structure. Here, the thin films were investigated using AFM, optical microscopy and polarized absorption spectroscopy. It was shown that by using numerical method for treating the polarized absorption spectroscopy data, the molecular structure can be elucidated. Further, it was shown that polarized optical spectroscopy is a general tool that allows determination of the molecular order in thin films. Finally, it was found that full control of thermal history and rigorous control of the ionic self-assembly conditions are required to reproducibly make these materials of high nanoscopic order. Similarly, the conditions for spin-casting are shown to be determining for the overall thin film morphology, while molecular order is maintained. PMID:29462883

Using Polarized Spectroscopy to Investigate Order in Thin-Films of Ionic Self-Assembled Materials Based on Azo-Dyes.

PubMed

Kühnel, Miguel R Carro-Temboury Martin; Ahmad, Mariam; Andersen, Frederik; Bech, Ári Brend; Bendixen, H Krestian L; Nawrocki, Patrick R; Bloch, Anders J; Bora, Ilkay; Bukhari, Tahreem A; Bærentsen, Nicolai V; Carstensen, Jens; Chima, Smeeah; Colberg, Helene; Dahm, Rasmus T; Daniels, Joshua A; Dinckan, Nermin; Idrissi, Mohamed El; Erlandsen, Ricci; Førster, Marc; Ghauri, Yasmin; Gold, Mikkel; Hansen, Andreas; Hansen, Kenn; Helmsøe-Zinck, Mathias; Henriksen, Mathias; Hoffmann, Sophus V; Hyllested, Louise O H; Jensen, Casper; Kallenbach, Amalie S; Kaur, Kirandip; Khan, Suheb R; Kjær, Emil T S; Kristiansen, Bjørn; Langvad, Sylvester; Lund, Philip M; Munk, Chastine F; Møller, Theis; Nehme, Ola M Z; Nejrup, Mathilde Rove; Nexø, Louise; Nielsen, Simon Skødt Holm; Niemeier, Nicolai; Nikolajsen, Lasse V; Nøhr, Peter C T; Orlowski, Dominik B; Overgaard, Marc; Ovesen, Jacob Skaarup; Paustian, Lucas; Pedersen, Adam S; Petersen, Mathias K; Poulsen, Camilla M; Praeger-Jahnsen, Louis; Qureshi, L Sonia; Ree, Nicolai; Schiermacher, Louise S; Simris, Martin B; Smith, Gorm; Smith, Heidi N; Sonne, Alexander K; Zenulovic, Marko R; Sørensen, Alma Winther; Sørensen, Karina; Vogt, Emil; Væring, Andreas; Westermann, Jonas; Özcan, Sevin B; Sørensen, Thomas Just

2018-02-15

Three series of ionic self-assembled materials based on anionic azo-dyes and cationic benzalkonium surfactants were synthesized and thin films were prepared by spin-casting. These thin films appear isotropic when investigated with polarized optical microscopy, although they are highly anisotropic. Here, three series of homologous materials were studied to rationalize this observation. Investigating thin films of ordered molecular materials relies to a large extent on advanced experimental methods and large research infrastructure. A statement that in particular is true for thin films with nanoscopic order, where X-ray reflectometry, X-ray and neutron scattering, electron microscopy and atom force microscopy (AFM) has to be used to elucidate film morphology and the underlying molecular structure. Here, the thin films were investigated using AFM, optical microscopy and polarized absorption spectroscopy. It was shown that by using numerical method for treating the polarized absorption spectroscopy data, the molecular structure can be elucidated. Further, it was shown that polarized optical spectroscopy is a general tool that allows determination of the molecular order in thin films. Finally, it was found that full control of thermal history and rigorous control of the ionic self-assembly conditions are required to reproducibly make these materials of high nanoscopic order. Similarly, the conditions for spin-casting are shown to be determining for the overall thin film morphology, while molecular order is maintained.

Method and apparatus for measuring nuclear magnetic properties

DOEpatents

Weitekamp, D.P.; Bielecki, A.; Zax, D.B.; Zilm, K.W.; Pines, A.

1987-12-01

A method for studying the chemical and structural characteristics of materials is disclosed. The method includes placement of a sample material in a high strength polarizing magnetic field to order the sample nuclei. The condition used to order the sample is then removed abruptly and the ordering of the sample allowed to evolve for a time interval. At the end of the time interval, the ordering of the sample is measured by conventional nuclear magnetic resonance techniques. 5 figs.

Method and apparatus for measuring nuclear magnetic properties

DOEpatents

Weitekamp, Daniel P.; Bielecki, Anthony; Zax, David B.; Zilm, Kurt W.; Pines, Alexander

1987-01-01

A method for studying the chemical and structural characteristics of materials is disclosed. The method includes placement of a sample material in a high strength polarizing magnetic field to order the sample nucleii. The condition used to order the sample is then removed abruptly and the ordering of the sample allowed to evolve for a time interval. At the end of the time interval, the ordering of the sample is measured by conventional nuclear magnetic resonance techniques.

Coprecipitation of arsenate with metal oxides. 3. Nature, mineralogy, and reactivity of iron(III)-aluminum precipitates.

PubMed

Violante, Antonio; Pigna, Massimo; Del Gaudio, Stefania; Cozzolino, Vincenza; Banerjee, Dipanjan

2009-03-01

Coprecipitation involving arsenic with aluminum or iron has been studied because this technique is considered particularly efficient for removal of this toxic element from polluted waters. Coprecipitation of arsenic with mixed iron-aluminum solutions has received scant attention. In this work we studied (i)the mineralogy, surface properties, and chemical composition of mixed iron-aluminum oxides formed at initial Fe/Al molar ratio of 1.0 in the absence or presence of arsenate [As/ Fe+Al molar ratio (R) of 0, 0.01, or 0.1] and at pH 4.0, 7.0, and 10.0 and aged for 30 and 210 days at 50 degrees C and (ii) the removal of arsenate from the coprecipitates after addition of phosphate. The amounts of short-range ordered precipitates (ferrihydrite, aluminous ferrihydrite and/or poorly crystalline boehmite) were greater than those found in iron and aluminum systems (studied in previous works), due to the capacity of both aluminum and arsenate to retard or inhibitthe transformation of the initially formed precipitates into well-crystallized oxides (gibbsite, bayerite, and hematite). As a consequence, the surface areas of the iron-aluminum oxides formed in the absence or presence of arsenate were usually much larger than those of aluminum or iron oxides formed under the same conditions. Arsenate was found to be associated mainly into short-range ordered materials. Chemical composition of all samples was affected by pH, initial R, and aging. Phosphate sorption was facilitated by the presence of short-range ordered materials, mainly those richer in aluminum, but was inhibited by arsenate present in the samples. The quantities of arsenate replaced by phosphate, expressed as percentages of its total amount present in the samples, were particularly low, ranging from 10% to 26%. A comparison of the desorption of arsenate by phosphate from aluminum-arsenate and iron-arsenate (studied in previous works) and iron-aluminum-arsenate coprecipitates evidenced that phosphate has a greater capacity to desorb arsenate from aluminum than iron sites.

Gettering in multicrystalline silicon: A design-of-experiments approach

NASA Astrophysics Data System (ADS)

Schubert, W. K.

1994-12-01

Design-of-experiment methods were used to study gettering due to phosphorus diffusion and aluminum alloying in four industrial multicrystalline silicon materials: Silicon-Film material from AstroPower, heat-exchanger method (HEM) material from Crystal Systems, edge-defined film-fed growth (EFG) material from Mobil Solar, and cast material from Solarex. Time and temperature for the diffusion and alloy processes were chosen for a four-factor quadratic interaction experiment. Simple diagnostic devices were used to evaluate the gettering. Only EFG and HEM materials exhibited statistically significant gettering effects within the ranges used for the various parameters. Diffusion and alloying temperature were significant for HEM material; also there was a second-order interaction between the diffusion time and temperature. There was no interaction between the diffusion and alloying processes in HEM material. EFG material showed a first-order dependence on diffusion temperature and a second-order interaction between the diffusion temperature and the alloying time. Gettering recommendations for the HEM material were used to produce the best-yet Sandia cells on this material, but correlation with the gettering experiment was not strong. Some of the discrepancy arises from necessary processing differences between the diagnostic devices and regular solar cells. This issue and other lessons learned concerning this type of experiment are discussed.

Nanophase and Composite Optical Materials

NASA Technical Reports Server (NTRS)

2003-01-01

This talk will focus on accomplishments, current developments, and future directions of our work on composite optical materials for microgravity science and space exploration. This research spans the order parameter from quasi-fractal structures such as sol-gels and other aggregated or porous media, to statistically random cluster media such as metal colloids, to highly ordered materials such as layered media and photonic bandgap materials. The common focus is on flexible materials that can be used to produce composite or artificial materials with superior optical properties that could not be achieved with homogeneous materials. Applications of this work to NASA exploration goals such as terraforming, biosensors, solar sails, solar cells, and vehicle health monitoring, will be discussed.

Evaluation of potential salivary acetaldehyde production from ethanol in oral cancer patients and healthy subjects

PubMed Central

Kocaelli, H; Apaydin, A; Aydil, B; Ayhan, M; Karadeniz, A; Ozel, S; Yılmaz, E; Akgün, B; Eren, B

2014-01-01

Background: Acetaldehyde has been implicated as a major factor in oral carcinogenesis associated with alcohol consumption. In this study, saliva samples from oral cancer patients and healthy individuals were incubated in vitro with ethanol in order to investigate factors which can influence salivary acetaldehyde production. Materials and Methods: A total of 66 individuals (40 males and 26 females, mean age 52 years) participated in the study. Participants were classified into three groups: Group 1 (oral cancer patients [n = 20]); Group 2 (poor dental health status [n = 25]) and Group 3 (good dental health status [n=21]). Every patient chewed a 1g piece of paraffin chewing gum for 1 minute then saliva samples were collected from all individuals. After in vitro incubation of the samples with ethanol, the levels of salivary acetaldehyde production was measured by head space gas chromatography. Kruskal-Wallis and Mann-Whitney tests and Spearman's Correlations analysis were performed for statistical analyses. Results: The salivary acetaldehyde production was significantly higher (p <0.0001) in both group 1 and group 2 when compared to group 3. However, there was no significant difference between group 1 and group 2. Poor dental health status, infrequent oral hygiene habits and dental visits, smoking and presence of a dental prosthesis were significant parameters for increased levels of salivary acetaldehyde production from alcohol. The evaluation of salivary acetaldehyde production after in vitro incubation with ethanol may be useful for early detection of oral cancer. Conclusion: According to the results of this study, the significantly higher levels of salivary acetaldehyde production in oral cancer patients and individuals with poor dental health status may suggest a possible link between increased salivary acetaldehyde production and oral cancer. Improved oral hygiene can effectively decrease the level of salivary acetaldehyde production in oral cavity. Hippokratia 2014; 18 (3): 269-274. PMID:25694764