ANALYTICAL METHOD FOR THE ABSORPTIOMETRIC DETERMINATION OF BORON IN SODIUM METAL

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1963-01-01

Sodium metal is dissolved in water under an inert atmosphere of argon, and the resulting sodium hydroxide solution is evaporated to dryness. Rosocyanin is formed, separated from excess curcumin, and dissolved in ethanol for absorptiometric measurement. The method is applicable to sodium metal containing 0.1 to 1 ppm boron. The precision should be within plus or minus 20% (95% confidence limits) at the 0.5 ppm boron level. (auth)

Some factors influencing susceptibility of rainbow trout to the acute toxicity of an ethyl mercury phosphate formulation (Timsan)

USGS Publications Warehouse

Amend, Donald F.; Yasutake, William T.; Morgan, Reginald

1969-01-01

This study determined the influence of water temperature (55–68° F), dissolved oxygen (4–12 ppm), water hardness as CaCO3 (20–256 ppm), and chloride ions (to 2 mM) on the susceptibility of rainbow trout (Salmo gairdneri) to the acute toxicity of ethyl mercury phosphate (EMP). The fish were exposed for one hour to 0.125 ppm EMP, the active ingredient of Timsan, a commercial EMP formulation. The death rate because of the exposure to EMP increased with an increase in water temperature, a decrease in dissolved oxygen, and an increase in chloride ions; calcium appeared to have no effect. The effect of water temperature and dissolved oxygen was ascribed to changes in the respiration rate of the fish, and a chemical explanation is presented for the effect of chloride ions.

Metal cycling along the northwestern Seward Peninsula, Alaska: A possible natural cause of metal contamination in the arctic: A section in Geologic studies in Alaska by the U.S. Geological Survey, 1997

USGS Publications Warehouse

Parnow, C.C.; Goldfarb, Richard J.; Kelley, Karen D.; York, Geoffrey S.

1999-01-01

The northwestern Seward Peninsula was targeted for detailed geochemical study after evaluation of data collected during the NURE reconnaissance-level program indicated anomalously high arsenic (60-635 ppm) concentrations in stream sediments. The arsenic is associated with tin skarn, greisen, and replacement deposits in the western Seward Peninsula. Surficial sampling of waters and sediments indicate that arsenic is being transported detritally but that solution transport is insignificant. Our new data indicate that sediments downstream from these tin occurrences are characterized by anomalous values of As (85- 530 ppm) and Sn (14-36 ppm), as well as consistent anomalies of Ag, Be, Cu, Sb, and W. Stream sediments collected from drainages underlain by slate, but distal to the exposed tin occurrences, are characterized by background levels of As ( 10-60 ppm), Li (16-80 ppm), Sn (5-14 ppm), and W (5-10 ppm). These background levels for As and Sn are much higher than concentrations in typical slates and suggest a broad, weak hydrothermal alteration during mineral-deposit formation in much of the study area. A consistent pattern of Ca>>Mg>Na>K and generally alkaline pH (7 .2-8.2) characterize waters throughout the study area. Dissolved sulfate concentrations range from 10 to 40 ppm for waters draining slates and from 3 to 20 ppm for water draining carbonates. The waters collected in areas of known tin occurrences in the Potato Mountain area are characterized by increased dissolved sulfate (43-75 ppm) and are generally acidic (pH 4.7-6.5), but most trace metals are at or below detection limits. Dissolved arsenic concentrations in the areas of known tin occurrences are at or below 2 ppb. Our data suggest that detrital arsenic and tin from mineral occurrences may be naturally entering the nearshore marine environment.

MODIFIED REVERSE OSMOSIS SYSTEM FOR TREATMENT OF PRODUCED WATERS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robert L. Lee; Junghan Dong

2004-06-03

This final report of ''Modified Reverse Osmosis System for Treatment of Produced Water,'' DOE project No. DE-FC26-00BC15326 describes work performed in the third year of the project. Several good results were obtained, which are documented in this report. The compacted bentonite membranes were replaced by supported bentonite membranes, which exhibited the same salt rejection capability. Unfortunately, it also inherited the clay expansion problem due to water invasion into the interlayer spaces of the compacted bentonite membranes. We noted that the supported bentonite membrane developed in the project was the first of its kind reported in the literature. An {alpha}-alumina-supported MFI-typemore » zeolite membrane synthesized by in-situ crystallization was fabricated and tested. Unlike the bentonite clay membranes, the zeolite membranes maintained stability and high salt rejection rate even for a highly saline solution. Actual produced brines from gas and oil fields were then tested. For gas fields producing brine, the 18,300 ppm TDS (total dissolved solids) in the produced brine was reduced to 3060 ppm, an 83.3% rejection rate of 15,240 ppm salt rejection. For oilfield brine, while the TDS was reduced from 181,600 ppm to 148,900 ppm, an 18% rejection rate of 32,700 ppm reduction, the zeolite membrane was stable. Preliminary results show the dissolved organics, mainly hydrocarbons, did not affect the salt rejection. However, the rejection of organics was inconclusive at this point. Finally, the by-product of this project, the {alpha}-alumina-supported Pt-Co/Na Y catalytic zeolite membrane was developed and demonstrated for overcoming the two-step limitation of nonoxidation methane (CH{sub 4}) conversion to higher hydrocarbons (C{sub 2+}) and hydrogen (H{sub 2}). Detailed experiments to obtain quantitative results of H{sub 2} generation for various conditions are now being conducted. Technology transfer efforts included five manuscripts submitted to peer-reviewed journals and five conference presentations.« less

Influence of dissolved oxygen concentration on the pharmacokinetics of alcohol in humans.

PubMed

Baek, In-hwan; Lee, Byung-yo; Kwon, Kwang-il

2010-05-01

Ethanol oxidation by the microsomal ethanol oxidizing system requires oxygen for alcohol metabolism, and a higher oxygen uptake increases the rate of ethanol oxidation. We investigated the effect of dissolved oxygen on the pharmacokinetics of alcohol in healthy humans (n = 49). The concentrations of dissolved oxygen were 8, 20, and 25 ppm in alcoholic drinks of 240 and 360 ml (19.5% v/v). Blood alcohol concentrations (BACs) were determined by converting breath alcohol concentrations. Breath samples were collected every 30 min when the BAC was higher than 0.015%, 20 min at BAC < or =0.015%, 10 min at BAC < or =0.010%, and 5 min at BAC < or =0.006%. The high dissolved oxygen groups (20, 25 ppm) descended to 0.000% and 0.050% BAC faster than the normal dissolved oxygen groups (8 ppm; p < 0.05). In analyzing pharmacokinetic parameters, AUC(inf) and K(el) of the high oxygen groups were lower than in the normal oxygen group, while C(max) and T(max) were not significantly affected. In a Monte Carlo simulation, the lognormal distribution of mean values of AUC(inf) and t(1/2) was expected to be reduced in the high oxygen group compared to the normal oxygen group. In conclusion, elevated dissolved oxygen concentrations in alcoholic drinks accelerate the metabolism and elimination of alcohol. Thus, enhanced dissolved oxygen concentrations in alcohol may have a role to play in reducing alcohol-related side effects and accidents.

Analysis of dissolved gas and fluid chemistry in mountainous region of Goaping river watershed in southern Taiwan

NASA Astrophysics Data System (ADS)

Tang, Kai-Wen; Chen, Cheng-Hong; Liu, Tsung-Kwei

2016-04-01

Annual rainfall in Taiwan is up to 2500 mm, about 2.5 times the average value of the world. However due to high topographic relief of the Central Mountain Range in Taiwan, groundwater storage is critical for water supply. Mountain region of the Goaping river watershed in southern Taiwan is one of the potential areas to develop groundwater recharge model. Therefore the target of this study is to understand sources of groundwater and surface water using dissolved gas and fluid chemistry. Four groundwater and 6 surface water samples were collected from watershed, 5 groundwater and 13 surface water samples were collected from downstream. All samples were analyzed for stable isotopes (hydrogen and oxygen), dissolved gases (including nitrogen, oxygen, argon, methane and carbon dioxide), noble gases (helium and radon) and major ions. Hydrogen and oxygen isotopic ratios of surface water and groundwater samples aligned along meteoric water line. For surface water, dissolved gases are abundant in N2 (>80%) and O2 (>10%); helium isotopic ratio is approximately equal to 1 RA (RA is 3He/4He ratio of air); radon-222 concentration is below the detection limit (<200 Bq/m3); and concentrations of major anions and cations are low (Na+ <20 ppm, Ca2+ < 60 ppm, Cl- <2 ppm). All these features indicate that surface waters are predominately recharged by precipitation. For groundwater, helium isotopic ratios (0.9˜0.23 RA) are lower and radon-222 concentrations (300˜6000 Bq/m3) are much higher than the surface water. Some samples have high amounts of dissolved gases, such as CH4 (>20%) or CO2 (>10%), most likely contributed by biogenic or geogenic sources. On the other hand, few samples that have temperature 5° higher than the average of other samples, show significantly high Na+ (>1000 ppm), Ca2+ (>150 ppm) and Cl- (>80 ppm) concentrations. An interaction between such groundwater and local hot springs is inferred. Watershed and downstream samples differ in dissolved gas species and fluid chemistry for groundwater and surface water. The higher hydrogen and oxygen isotopic ratios for surface water from downstream are most probably caused by evaporation. Low radon-222 concentrations of some groundwater from downstream may represent sources from different aquifers. Therefore, we conclude that surface water from downstream are recharged directly from its watershed, but groundwater are influenced by the local geological environment. Keywords: groundwater, dissolved gas, noble gas, radon in water, 3He/4He

Recovery of Fresh Water Resources from Desalination of Brine Produced During Oil and Gas Production Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

David B. Burnett; Mustafa Siddiqui

2006-12-29

Management and disposal of produced water is one of the most important problems associated with oil and gas (O&G) production. O&G production operations generate large volumes of brine water along with the petroleum resource. Currently, produced water is treated as a waste and is not available for any beneficial purposes for the communities where oil and gas is produced. Produced water contains different contaminants that must be removed before it can be used for any beneficial surface applications. Arid areas like west Texas produce large amount of oil, but, at the same time, have a shortage of potable water. Amore » multidisciplinary team headed by researchers from Texas A&M University has spent more than six years is developing advanced membrane filtration processes for treating oil field produced brines The government-industry cooperative joint venture has been managed by the Global Petroleum Research Institute (GPRI). The goal of the project has been to demonstrate that treatment of oil field waste water for re-use will reduce water handling costs by 50% or greater. Our work has included (1) integrating advanced materials into existing prototype units and (2) operating short and long-term field testing with full size process trains. Testing at A&M has allowed us to upgrade our existing units with improved pre-treatment oil removal techniques and new oil tolerant RO membranes. We have also been able to perform extended testing in 'field laboratories' to gather much needed extended run time data on filter salt rejection efficiency and plugging characteristics of the process train. The Program Report describes work to evaluate the technical and economical feasibility of treating produced water with a combination of different separation processes to obtain water of agricultural water quality standards. Experiments were done for the pretreatment of produced water using a new liquid-liquid centrifuge, organoclay and microfiltration and ultrafiltration membranes for the removal of hydrocarbons from produced water. The results of these experiments show that hydrocarbons from produced water can be reduced from 200 ppm to below 29 ppm level. Experiments were also done to remove the dissolved solids (salts) from the pretreated produced water using desalination membranes. Produced water with up to 45,000 ppm total dissolved solids (TDS) can be treated to agricultural water quality water standards having less than 500 ppm TDS. The Report also discusses the results of field testing of various process trains to measure performance of the desalination process. Economic analysis based on field testing, including capital and operational costs, was done to predict the water treatment costs. Cost of treating produced water containing 15,000 ppm total dissolved solids and 200 ppm hydrocarbons to obtain agricultural water quality with less than 200 ppm TDS and 2 ppm hydrocarbons range between $0.5-1.5 /bbl. The contribution of fresh water resource from produced water will contribute enormously to the sustainable development of the communities where oil and gas is produced and fresh water is a scarce resource. This water can be used for many beneficial purposes such as agriculture, horticulture, rangeland and ecological restorations, and other environmental and industrial application.« less

The effect of iron content and dissolved O2 on dissolution rates of clinopyroxene at pH 5.8 and 25°C: Preliminary results

USGS Publications Warehouse

Hoch, A.R.; Reddy, M.M.; Drever, J.I.

1996-01-01

Dissolution experiments using augite (Mg0.87Ca0.85Fe0.19Na0.09Al0.03Si2O6) and diopside (Mg0.91Ca0.93Fe0.07Na0.03Al0.03Si2O6) were conducted in flow-through reactors (5-ml/h flow rate). A pH of 5.8 was maintained by bubbling pure CO2 through a solution of 0.01 M KHCO3 at 25°C. Two experiments were run for each pyroxene type. In one experiment dissolved O2 concentration in reactors was 0.6 (±0.1) ppm and in the second dissolved O2 was 1.5 (±0.1) ppm. After 60 days, augite dissolution rates (based on Si release) were approximately three times greater in the 1.5 ppm. dissolved O2 experiments than in the sealed experiments. In contrast, diopside dissolution rates were independent of dissolved O2 concentrations. Preliminary results from the augite experiments suggest that dissolution rate is directly related to oxidation of iron. This effect was not observed in experiments performed on iron-poor diopside. Additionally, dissolution rates of diopside were much slower than those of augite, again suggesting a relationship between Fe content, Fe oxidation and dissolution rates.

X-ray fluorescence measurements of dissolved gas and cavitation

DOE PAGES

Duke, Daniel J.; Kastengren, Alan L.; Swantek, Andrew B.; ...

2016-09-28

The dynamics of dissolved gas and cavitation are strongly coupled, yet these phenomena are difficult to measure in-situ. Both create voids in the fluid that can be difficult to distinguish. In this paper, we present an application of X-ray fluorescence in which liquid density and total noncondensible gas concentration (both dissolved and nucleated) are simultaneously measured. The liquid phase is doped with 400 ppm of a bromine tracer, and dissolved air is removed and substituted with krypton. Fluorescent emission at X-ray wavelengths is simultaneously excited from the Br and Kr with a focused monochromatic X-ray beam from a synchrotron source.more » We measure the flow in a cavitating nozzle 0.5 mm in diameter. From Br fluorescence, total displacement of the liquid is measured. From Kr fluorescence, the mass fraction of both dissolved and nucleated gas is measured. Volumetric displacement of liquid due to both cavitation and gas precipitation can be separated through estimation of the local equilibrium dissolved mass fraction. The uncertainty in the line of sight projected densities of the liquid and gas phases is 4–6 %. The high fluorescence yields and energies of Br and Kr allow small mass fractions of gas to be measured, down to 10 -5, with an uncertainty of 8 %. Finally, these quantitative measurements complement existing optical diagnostic techniques and provide new insight into the diffusion of gas into cavitation bubbles, which can increase their internal density, pressure and lifetimes by orders of magnitude.« less

PRESERVATION OF SULFIDIC WATERS CONTAINING DISSOLVED AS (III)

EPA Science Inventory

Solutions containing variable concentrations of sulfide (p to31 ppm) and arsenite (0.35 to 10 ppm) were subjected to several different preservation treatments. As predicted by equilibrium thermodynamics, at near-neutral pH the experimental solutions were undersaturated with resp...

Salinity of the ground water in western Pinal County, Arizona

USGS Publications Warehouse

Kister, Lester Ray; Hardt, W.F.

1966-01-01

The chemical quality of the ground water in western Pinal County is nonuniform areally and stratigraphically. The main areas of highly mineralized water are near Casa Grande and near Coolidge. Striking differences have been noted in the quality of water from different depths in the same well. Water from one well, (D-6-7) 25cdd, showed an increase in chloride content from 248 ppm (parts per million) at 350 feet below the land surface to 6,580 ppm at 375 feet; the concentration of chloride increased to 10,400 ppm at 550 feet below the land surface. This change was accompanied by an increase in the total dissolved solids as indicated by conductivity measurements. The change in water quality can be correlated with sediment types. The upper and lower sand and gravel units seem to yield water of better quality than the intermediate silt and clay unit. In places the silt and clay unit contains zones of gypsum and common table salt. These zones yield water that contains large amounts of the dissolved minerals usually associated with water from playa deposits. Highly mineralized ground water in an area near Casa Grande has moved southward and westward as much as 4 miles. Similar water near Coolidge has moved a lesser distance. Good management practices and proper use of soil amendments have made possible the use of water that is high in salinity and alkali hazard for agricultural purposes in western Pinal County. The fluoride content of the ground water in western Pinal County is usually low; however, water from wells that penetrate either the bedrock or unconsolidated sediments that contain certain volcanic rocks may have as much as 9 ppm of fluoride.

Zinc oxide nanoparticle toxicity in embryonic zebrafish: Mitigation with different natural organic matter.

PubMed

Kteeba, Shimaa M; El-Adawi, Hala I; El-Rayis, Osman A; El-Ghobashy, Ahmed E; Schuld, Jessica L; Svoboda, Kurt R; Guo, Laodong

2017-11-01

Exposure experiments were conducted to evaluate the influence of dissolved organic matter (DOM) on the toxicity of ZnO-NPs (10-30 nm) and dissolved Zn at sub-lethal doses (50 and 5 ppm, respectively) to zebrafish (Danio rerio). Humic acid, alginic acid, bovine serum albumin and various natural DOM isolated from rivers as the Milwaukee River-WI (NOMW), Yukon River-AK (NOMA) and Suwannee River-GA DOM (NOMS) were used to represent humic substances (HA), carbohydrates (CHO), proteins (PTN), and natural organic matter (NOM), respectively. Initial experiments were carried out to confirm the toxic effect of ZnO-NPs at 50 ppm, followed by mitigation experiments with different types and concentrations of DOM (0.4-40 mg-C/L). Compared to 0% hatch of 50 ppm ZnO-NPs exposed embryos at 72 h post fertilization (hpf), NOMS, NOMW and HA had the best mitigative effects on hatching (53-65%), followed by NOMA, CHO and PTN (19-35%); demonstrating that the mitigation effects on ZnO-NPs toxicity were related to DOM's quantity and composition. At 96 hpf, 20% of embryos exposed to 50 ppm ZnO-NPs hatched, 100% of embryos reared in embryo medium hatched, and close to 100% of the embryos hatched upon mitigation, except for those mitigated with PTN which had less effect. Dissolved Zn (5 ppm) also exhibited the same toxicity on embryos as ZnO-NPs (50 ppm). However, in the presence of HA, NOM and CHO, the hatching rates at 72 and 96 hpf increased significantly compared to 5% hatch without DOM. The overall mitigation effects produced by DOM followed the order of HA ≥ NOMS > NOM (A&W) > CHO > PTN, although specific mitigation effects varied with DOM concentration and functionalities. Our results also indicate that the toxicity of ZnO-NPs to embryos was mostly derived from NPs although dissolved Zn released from ZnO-NPs also interacted with embryos, affecting hatching, but to a less extent. Copyright © 2017 Elsevier Ltd. All rights reserved.

Analysis of elemental concentration using ICP-AES and pathogen indicator in drinking water of Qasim Abad, District Rawalpindi, Pakistan.

PubMed

Sehar, Shama; Naz, Iffat; Ali, Naeem; Ahmed, Safia

2013-02-01

The present study was conducted to investigate drinking water quality (groundwater) from water samples taken from Qasim Abad, a locality of approximately 5,000 population, situated between twin cities Rawalpindi and Islamabad in Pakistan. The main sources of drinking water in this area are water bores which are dug upto the depth of 250-280 ft in almost every house. The study consists of the determination of physico-chemical properties, trace metals, heavy metals, rare earth elements and microbiological quality of drinking water. The data showed the variation of the investigated parameters in samples as follows: pH 6.75 to 8.70, electrical conductivity 540 to 855 μS/cm, total dissolved solids 325.46 to 515.23 ppm and dissolved oxygen 1.50 to 5.64 mg/L which are within the WHO guidelines for drinking water quality. The water samples were analysed for 30 elements (aluminium, iron, magnesium, manganese, silicon, zinc, molybdenum, titanium, chromium, nickel, tungsten, silver, arsenic, boron, barium, beryllium, cadmium, cobalt, copper, gallium, mercury, lanthanum, niobium, neodymium, lead, selenium, samarium, tin, vanadium and zirconium) by using inductively coupled plasma atomic emission spectroscopy. The organic contamination was detected in terms of most probable number (MPN) of faecal coliforms. Overall, elemental levels were lower than the recommended values but three water bores (B-1, B-6, B-7) had higher values of iron (1.6, 2.206, 0.65 ppm), two water bores (B-1, B-6) had higher values of aluminium (0.95, 1.92 ppm), respectively, and molybdenum was higher by 0.01 ppm only in one water bore (B-11). The total number of coliforms present in water samples was found to be within the prescribed limit of the WHO except for 5 out of 11 bore water samples (B-2, B-3, B-4, B-8, B-11), which were found in the range 5-35 MPN/100 mL, a consequence of infiltration of contaminated water (sewage) through cross connection, leakage points and back siphoning.

The hydrogen-storing microporous silica 'Microcluster' reduces acetaldehyde contained in a distilled spirit.

PubMed

Kato, Shinya; Miwa, Nobuhiko

2016-12-01

Acetaldehyde is a detrimental substance produced in alcoholic liquor aging. We assessed an ability of hydrogen-storing microporous silica 'Microcluster' (MC+) to reduce acetaldehyde, as compared with autoclave-dehydrogenated MC+ (MC-). Acetaldehyde was quantified spectrophotometrically by an enzymatic method. Authentic acetaldehyde was treated by MC+ for 20min, and decreased from 43.4ppm to 10.9ppm, but maintained at 49.3ppm by MC-. On the other hand, acetaldehyde contained in a distilled spirit was decreased from 29.5ppm to 3.1ppm at 20min by MC+, but not decreased by MC-. Addition of MC+ or MC- to distilled water without acetaldehyde showed no seeming effect on the quantification used. Accordingly acetaldehyde in a distilled spirit is reduced to ethanol by hydrogen contained in MC+, but not by the silica moiety of MC+. Hydrogen gas of 1.2mL was released for 20min from MC+ of 0.59g in water, resulting in dissolved hydrogen of 1.09ppm and an oxidation- reduction potential of -687.0mV indicative of a marked reducing ability. Thus, MC+ has an ability to reduce acetaldehyde in a distilled spirit due to dissolved hydrogen released from MC+. Copyright © 2016 Elsevier B.V. All rights reserved.

Dissolved organic matter in the unsaturated zone: the view from the cave

NASA Astrophysics Data System (ADS)

Baker, A.; Duan, W.; Rutlidge, H.; McDonough, L.; Oudone, P.; Meredith, K.; Andersen, M. S.; O'Carroll, D. M.; Coleborn, K.; Treble, P. C.

2017-12-01

Soil organic matter content is typically a few percent of the total soil composition. Diffuse recharge can mobilise some of this soil-derived organic matter. While soil pore water dissolved organic matter (DOM) concentrations are up to 100 ppm, the resulting groundwater dissolved organic matter concentration is typically less than 2ppm. Dissolved organic matter transported from the soil can be both biodegraded and sorbed to minerals, and the relative importance of these two processes in the unsaturated zone is poorly understood. Caves in karstified limestone uniquely provide direct access to water percolating from the soil to the groundwater. Cave percolation waters can be analysed for their DOM concentration and character. This provides insights into the extent and type of biological and chemical processing of DOM during transport from the soil to the groundwater. We determine the concentration and characteristics of DOM in cave percolation waters using liquid chromatography (LC-OCD) and optical spectrophotometry (fluorescence and absorbance). We sample DOM from multiple caves in SE Australia (Cathedral Cave, Wellington; South Glory and Harrie Wood Caves, Yarrangobilly), permitting comparison of unsaturated zone DOM properties at different depths (up to 30m below land surface) and different climate zones (montane and temperate). We use caves with long-term hydrological monitoring programs so that DOM in waters of contrasting residence times can be compared. Additionally, we compare these cave percolation water DOM characteristics to those from local and regional groundwater, sampled from nearby wells. Our results will help improve our understanding of how DOM is processed from soil to groundwater, and is also relevant to speleothem scientists interested in using organic matter preserved in speleothems as a paleoclimate or paleoenvironmental proxy.

Developing monitoring plans to detect spills related to natural gas production.

PubMed

Harris, Aubrey E; Hopkinson, Leslie; Soeder, Daniel J

2016-11-01

Surface water is at risk from Marcellus Shale operations because of chemical storage on drill pads during hydraulic fracturing operations, and the return of water high in total dissolved solids (up to 345 g/L) from shale gas production. This research evaluated how two commercial, off-the-shelf water quality sensors responded to simulated surface water pollution events associated with Marcellus Shale development. First, peak concentrations of contaminants from typical spill events in monitored watersheds were estimated using regression techniques. Laboratory measurements were then conducted to determine how standard in-stream instrumentation that monitor conductivity, pH, temperature, and dissolved oxygen responded to three potential spill materials: ethylene glycol (corrosion inhibitor), drilling mud, and produced water. Solutions ranging from 0 to 50 ppm of each spill material were assessed. Over this range, the specific conductivity increased on average by 19.9, 27.9, and 70 μS/cm for drilling mud, ethylene glycol, and produced water, respectively. On average, minor changes in pH (0.5-0.8) and dissolved oxygen (0.13-0.23 ppm) were observed. While continuous monitoring may be part of the strategy for detecting spills to surface water, these minor impacts to water quality highlight the difficulty in detecting spill events. When practical, sensors should be placed at the mouths of small watersheds where drilling activities or spill risks are present, as contaminant travel distance strongly affects concentrations in surface water systems.

Differences in mortality among bobwhite fed methylmercury chloride dissolved in various carriers

USGS Publications Warehouse

Spann, J.W.; Heinz, G.H.; Camardese, M.B.; Hill, E.F.; Moore, John F.; Murray, H.C.

1986-01-01

Twelve-day-old bobwhite chicks were fed a diet containing 0, 5.4 or 20 ppm methylmercury chloride. The methylmercury chloride was added to the diet either in a dry, pulverized form or dissolved in acetone, propylene glycol or corn oil. Mortality was measured for 6 weeks, and samples of liver were saved for mercury analysis. Mortality was significantly lower in birds fed 20 ppm methylmercury chloride when acetone was the solvent. The reduced mortality could not be explained by effects of acetone on dietary level of mercury or on uptake of mercury into the body.

Purification of oily wastewater by hybrid UF/MD.

PubMed

Gryta, M; Karakulski, K; Morawski, A W

2001-10-01

Investigations on the treatment of oily wastewater by a combination of ultrafiltration (UF) and membrane distillation (MD) as a final purification method have been performed. A tubular UF module equipped with polyvinylidene fluoride (PVDF) membranes and a capillary MD module with polypropylene membranes were tested using a typical bilge water collected from a harbour without pretreatment. The permeate obtained from the UF process generally contains less than 5 ppm of oil. A further purification of the UF permeate by membrane distillation results in a complete removal of oil from wastewater and a very high reduction of the total organic carbon (99.5%) and total dissolved solids (99.9%).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duke, Daniel J.; Kastengren, Alan L.; Swantek, Andrew B.

The dynamics of dissolved gas and cavitation are strongly coupled, yet these phenomena are difficult to measure in-situ. Both create voids in the fluid that can be difficult to distinguish. In this paper, we present an application of X-ray fluorescence in which liquid density and total noncondensible gas concentration (both dissolved and nucleated) are simultaneously measured. The liquid phase is doped with 400 ppm of a bromine tracer, and dissolved air is removed and substituted with krypton. Fluorescent emission at X-ray wavelengths is simultaneously excited from the Br and Kr with a focused monochromatic X-ray beam from a synchrotron source.more » We measure the flow in a cavitating nozzle 0.5 mm in diameter. From Br fluorescence, total displacement of the liquid is measured. From Kr fluorescence, the mass fraction of both dissolved and nucleated gas is measured. Volumetric displacement of liquid due to both cavitation and gas precipitation can be separated through estimation of the local equilibrium dissolved mass fraction. The uncertainty in the line of sight projected densities of the liquid and gas phases is 4–6 %. The high fluorescence yields and energies of Br and Kr allow small mass fractions of gas to be measured, down to 10 -5, with an uncertainty of 8 %. Finally, these quantitative measurements complement existing optical diagnostic techniques and provide new insight into the diffusion of gas into cavitation bubbles, which can increase their internal density, pressure and lifetimes by orders of magnitude.« less

Enhanced Indirect Somatic Embryogenesis of Date Palm Using Low Levels of Seawater.

PubMed

Taha, Rania A

2017-01-01

Date palm tolerates salinity, drought, and high temperatures. Arid and semiarid zones, especially the Middle East region, need a huge number of date palms for cultivation. To meet this demand, tissue culture techniques have great potential for mass production of plantlets, especially using the indirect embryogenesis technique; any improvement of these techniques is a worthy objective. Low levels of salinity can enhance growth and development of tolerant plants. A low level of seawater, a natural source of salinity, reduces the time required for micropropagation processes of date palm cv. Malkaby when added to MS medium. Medium containing seawater at 500 ppm total dissolved solid (TDS) (12.2 mL/L) improves callus proliferation, whereas 1500 ppm (36.59 mL/L) enhances plant regeneration including multiplication of secondary embryos, embryo germination, and rooting.

Study of Groundwater Physical Characteristics: A Case Study at District of Pekan, Pahang

NASA Astrophysics Data System (ADS)

Hashim, M. M. M.; Zawawi, M. H.; Samuding, K.; Dominic, J. A.; Zulkurnain, M. H.; Mohamad, K.

2018-04-01

A study of groundwater physical characteristic has been conducted at Pahang Tua, Pekan, Tanjung Batu and Nenasi, Pahang. There are several locations of tube well selected in this study. Four of five locations are situated in the coastal area and another one is located outside of coastal line. The purposes of this study are to identify the physical characteristic of groundwater (temperature, pH, electrical conductivity (EC), total dissolved solids (TDS) and salinity) and to identify the influence of sampling location and tube well depth to its physical characteristics. The results from the in-situ measurement were identified the physical characteristic groundwater for each tube well location. The result shows that temperature and pH for all groundwater samples almost in the same value but for the electrical conductivity, salinity and total dissolved solid have significant difference that related to location and depth of the tube well. The Pekan tube well with 80m depth and 2km distance from the sea have the highest value of EC, TDS and salinity (14460.53µS/cm, 7230.63 ppm and 8.32 PSU) compared to Nenasi with 30m depth of tube well and 0.65km distance from the sea. The EC, TDS and salinity value recorded are 1454.3253µS/cm, 727.00 ppm and 0.72 PSU. From the result of EC, TDS and salinity, it shows that the deeper tube well in the coastal area will obtained higher value of EC, TDS and salinity.

Renewable Energy Capability vs. Climate Necessity

ERIC Educational Resources Information Center

Mills, David

2006-01-01

A 450-ppm equivalent CO[2] target by 2050 is an often-proposed goal under a future global emissions agreement, but there is considerable high side risk in global-warming models due to cloud formation, feedbacks in dissolved organic carbon from peat bogs in polar regions, and unaccounted solar dimming by particulates. The 450-ppm figure is…

Delaware River water quality Bristol to Marcus Hook, Pennsylvania, August 1949 to December 1963

USGS Publications Warehouse

Keighton, Walter B.

1965-01-01

During the 14-year period from August 1949 to July 1963, the U.S. Geological Survey, in cooperation with the city of Philadelphia, collected samples of river water once each month in the 43-mile reach of the Delaware River from Bristol to Marcus Hook, Pa., and daily at Trenton, 10 miles upstream from Bristol. This part of the Delaware is an estuary into which salt water is brought by tides; fresh water flows into the estuary at Trenton, NJ, and farther downstream from the Schuylkill River and other tributaries of the Delaware. In March, April, and May, when fresh-water flow is high, the average concentration of dissolved solids in the water at Bristol was 76 ppm (parts per million), and at Marcus Hook 112 PPM In August and September, streamflow is lower, and the average concentration of dissolved solids increased to 117 PPM at Bristol and 804 PPM at Marcus Hook. Major salinity invasions of the Delaware River occurred in 1949, 1953, 1954, 1957, and 1963. In each of these years the fresh-water flow into the tidal river at Trenton was low during the period from July to October. The greatest dissolved-solids concentrations in these monthly samples were 160 PPM at Bristol and 4,000 PPM at Marcus Hook. At times the dissolved-oxygen concentration of the river water has become dangerously low, especially in that reach of the river between Wharton Street and League Island. At the Benjamin Franklin Bridge, one-third of the samples of river water were less than 30 percent saturated with oxygen; however, no trend, either for better or for worse, was apparent during the 14-year period. It is useful now to summarize these monthly analyses for the period 1949-63 even though a much more detailed description of water quality in this reach of the estuary will soon become available through the use of recording instrumental conditions. This compendium of water-quality data is useful as an explicit statement of water quality during the 14-year study period and is valuable for directing attention to water-quality problems for selecting instrument sites, and for making comparative studies with the more detailed information which is already being obtained with the aid of recording instruments.

Using cerium anomaly as an indicator of redox reactions in constructed wetland

NASA Astrophysics Data System (ADS)

Liang, R.

2013-12-01

The study area, Chiayi County located in southern Taiwan, has highly developed livestock. The surface water has very low dissolved oxygen and high NH4. Under the situation, constructed wetland becomes the most effective and economic choice to treat the wastewater in the natural waterways. Hebao Island free surface constructed wetland started to operate in late 2006. It covers an area of 0.28 km2 and is subdivided into 3 major cells, which are sedimentation cell, 1st aeration cell with rooted plants and 2nd aeration cell with float plants. The water depth of cells ranges from 0.6 m to 1.2 m. The total hydraulic retention time is about a half day. In this study, the water samples were sequentially collected along the flow path. The results of hydrochemical analysis show that the untreated inflow water can be characterized with enriched NH4 (11 ppm), sulfate (6 ppm) and arsenic (50 ppb). The removal efficiency of NH4 in the first two cells is <15%. However, the efficiency dramatically increases in the 2nd aeration cell, which is over 90%. Simultaneously, almost all of the hydrochemical properties, including EC, Ca, Mg, As Fe, Mn and other heavy metals, decrease while dissolve oxygen increases close to saturated level and aluminum is almost doubled in the exit of constructed wetland. However, the removal of sulfate and phosphate is very weak. It is worth to note that arsenic is still higher than the permissible limits recommended by WHO (10 ppb). The wetland operation should be tuned to take more arsenic away in the future. As demonstrated in the above, oxidation reaction is the most dominant mechanism to remove pollutants from the wastewater; therefore, dissolved oxygen is traditionally considered as an important indicator to evaluate the operation efficiency of wetland. However, it would need longer time to achieve equilibrium state of redox reaction involving dissolved oxygen due to the slower reaction rate. For example, the input water in this study has fairly high dissolved oxygen (5 ppm) but the NH4 content is still high, which indicates a non-equilibrium condition. In this study, the cerium anomaly is alternatively utilized to evaluate the water redox state. The results demonstrate that the input water has the negative cerium anomaly of -0.16. Along the flow path, the cerium negative anomaly does not change in the first two cells and dramatically becomes -0.23 in cell 3. The trend of cerium anomaly is more close to the removal efficiency of NH4 rather than dissolve oxygen. Accordingly, cerium anomaly could become a better indicator of removal efficiency of constructed wetland.

Genetic legacy of the deep subsurface recorded in the outflow channel of a terrestrial serpentinizing seep (Luzon, the Philippines)

NASA Astrophysics Data System (ADS)

Woycheese, K. M.; Meyer-Dombard, D. R.; Cardace, D.; Arcilla, C. A.

2014-12-01

The deep subsurface microbial community represents the largest biome on Earth, yet accessing this deep biosphere is challenging. Fluids seep along fractures from aquifers that may support diverse microbial communities, living off hydrogen gas generated by radiolysis, serpentinization, or thermogenic reactions. A serpentinizing seep, emanating fluids as high as pH 11.27, was found to accrete meters-long carbonate terraces in the Zambales ophiolite range (Luzon, the Philippines). Samples were collected at several locations along the Poon Bato (PB) River, focusing primarily on the pools and terraces formed by carbonate rimstone (Figure 1). As serpentinizing fluids are exposed to the atmosphere, dynamic niches are established in surface sediments. We propose that the high pH, reducing, high Ca+2 fluid pool terraces reflect remnants of deep subsurface microbial communities, based on high-throughput 16S rRNA sequencing data. In total, eight samples were collected for environmental DNA analysis. Post-sequence analysis revealed a total of 927126 counts, with an average of 115890.75 counts per sample. Many taxa aligned with cultured representatives of serpentinizing seep-associated taxa, including Bacteroidetes, Clostrida, Chloroflexi, Methylococcales, and Xanthomonadales. Geochemical data indicates an average fluid temperature of 28.9°C, and pH that varies from 9.22-11.27. Total carbon wt.% of solids was highest in a shallow pool shaped by boulders, where calcite precipitation occurred over nearly every surface. Dissolved oxygen (DO%) was highest at PB1 main pool (60%), although a calcite skin had formed along the air-water interface. Dissolved inorganic carbon (DIC) at PB1 main pool was 1.3 ppm, while at PB2 main pool, the DIC was higher (6.0 ppm). The lack of calcite skin may allow more direct access to atmospheric carbon dioxide at PB2. The isotopic value of carbon-13 was depleted at PB1 relative to PB2 (δ13C VPDB -25.4 ‰ versus δ13C VPDB ‰ -17.5, respectively). The DOC concentration at PB1 main pool was 0.3 ppm and 1.15 ppm at PB2. Given the low DIC concentrations at PB1, it is suggested that heterotrophy may dominate over autotrophy in the system. This suggests that the highly reducing, high pH fluids emanating from fluid seeps at Poon Bato influence surface communities via inundation with serpentinizing fluid.

Module for Oxygenating Water without Generating Bubbles

NASA Technical Reports Server (NTRS)

Gonzalez-Martin, Anuncia; Sidik, Reyimjan; Kim, Jinseong

2004-01-01

A module that dissolves oxygen in water at concentrations approaching saturation, without generating bubbles of oxygen gas, has been developed as a prototype of improved oxygenators for water-disinfection and water-purification systems that utilize photocatalyzed redox reactions. Depending on the specific nature of a water-treatment system, it is desirable to prevent the formation of bubbles for one or more reasons: (1) Bubbles can remove some organic contaminants from the liquid phase to the gas phase, thereby introducing a gas-treatment problem that complicates the overall water-treatment problem; and/or (2) in some systems (e.g., those that must function in microgravity or in any orientation in normal Earth gravity), bubbles can interfere with the flow of the liquid phase. The present oxygenation module (see Figure 1) is a modified version of a commercial module that contains >100 hollow polypropylene fibers with a nominal pore size of 0.05 m and a total surface area of 0.5 m2. The module was originally designed for oxygenation in a bioreactor, with no water flowing around or inside the tubes. The modification, made to enable the use of the module to oxygenate flowing water, consisted mainly in the encapsulation of the fibers in a tube of Tygon polyvinyl chloride (PVC) with an inside diameter of 1 in. (approx.=25 mm). In operation, water is pumped along the insides of the hollow fibers and oxygen gas is supplied to the space outside the hollow tubes inside the PVC tube. In tests, the pressure drops of water and oxygen in the module were found to be close to zero at water-flow rates ranging up to 320 mL/min and oxygen-flow rates up to 27 mL/min. Under all test conditions, no bubbles were observed at the water outlet. In some tests, flow rates were chosen to obtain dissolved-oxygen concentrations between 25 and 31 parts per million (ppm) . approaching the saturation level of approx.=35 ppm at a temperature of 20 C and pressure of 1 atm (approx.=0.1 MPa). As one would expect, it was observed that the time needed to bring a flow of water from an initial low dissolved-oxygen concentration (e.g., 5 ppm) to a steady high dissolved-oxygen concentration at or near the saturation level depends on the rates of flow of both oxygen and water, among other things. Figure 2 shows the results of an experiment in which a greater flow of oxygen was used during the first few tens of minutes to bring the concentration up to approx.=25 ppm, then a lesser flow was used to maintain the concentration.

Concentrations and isotope ratios of carbon, nitrogen and sulfur in ocean-floor basalts

USGS Publications Warehouse

Sakai, H.; Marais, D.J.D.; Ueda, A.; Moore, J.G.

1984-01-01

Fresh submarine basalt glasses from Galapagos Ridge, FAMOUS area, Cayman Trough and Kilauea east rift contain 22 to 160 ppm carbon and 0.3 to 2.8 ppm nitrogen, respectively, as the sums of dissolved species and vesicle-filling gases (CO2 and N2). The large range of variation in carbon content is due to combined effect of depth-dependency of the solubility of carbon in basalt melt and varying extents of vapour loss during magma emplacement as well as in sample crushing. The isotopic ratios of indigenous carbon and nitrogen are in very narrow ranges,-6.2 ?? 0.2% relative to PDB and +0.2 ?? 0.6 %. relative to atmospheric nitrogen, respectively. In basalt samples from Juan de Fuca Ridge, however, isotopically light carbon (??13C = around -24%.) predominates over the indigenous carbon; no indigenous heavy carbon was found. Except for Galapagos Ridge samples, these ocean-floor basalts contain 670 to 1100 ppm sulfur, averaging 810 ppm, in the form of both sulfide and sulfate, whereas basalts from Galapagos Ridge are higher in both sulfur (1490 and 1570 ppm) and iron (11.08% total iron as FeO). The ??34S values average +0.3 ?? 0.5%. with average fractionation factor between sulfate and sulfide of +7.4 ?? 1.6%.. The sulfate/sulfide ratios tend to increase with increasing water content of basalt, probably because the oxygen fugacity increases with increasing water content in basalt melt. ?? 1984.

Concentrations and isotope ratios of carbon, nitrogen and sulfur in ocean-floor basalts.

PubMed

Sakai, H; Des Marais, D J; Ueda, A; Moore, J G

1984-01-01

Fresh submarine basalt glasses from Galapagos Ridge, FAMOUS area, Cayman Trough and Kilauea east rift contain 22 to 160 ppm carbon and 0.3 to 2.8 ppm nitrogen, respectively, as the sums of dissolved species and vesicle-filling gases (CO2 and N2). The large range of variation in carbon content is due to combined effect of depth-dependency of the solubility of carbon in basalt melt and varying extents of vapour loss during magma emplacement as well as in sample crushing. The isotopic ratios of indigenous carbon and nitrogen are in very narrow ranges, -6.2 +/- 0.2% relative to PDB and +0.2 +/- 0.6% relative to atmospheric nitrogen, respectively. In basalt samples from Juan de Fuca Ridge, however, isotopically light carbon (delta 13 C = around -24%) predominates over the indigenous carbon; no indigenous heavy carbon was found. Except for Galapagos Ridge samples, these ocean-floor basalts contain 670 to 1100 ppm sulfur, averaging 810 ppm in the form of both sulfide and sulfate, whereas basalts from Galapagos Ridge are higher in both sulfur (1490 and 1570 ppm) and iron (11.08% total iron as FeO). the delta 34S values average +0.3 +/- 0.5% with average fractionation factor between sulfate and sulfide of +7.4 +/- 1.6%. The sulfate/sulfide ratios tend to increase with increasing water content of basalt, probably because the oxygen fugacity increases with increasing water content in basalt melt.

Organic matter in central California radiation fogs.

PubMed

Herckes, Pierre; Lee, Taehyoung; Trenary, Laurie; Kang, Gongunn; Chang, Hui; Collett, Jeffrey L

2002-11-15

Organic matter was studied in radiation fogs in the San Joaquin Valley of California during the California Regional Particulate Air Quality Study (CRPAQS). Total organic carbon (TOC) concentrations ranged from 2 to 40 ppm of C. While most organic carbon was found in solution as dissolved organic carbon (DOC), 23% on average was not dissolved inside the fog drops. We observe a clear variation of organic matter concentration with droplet size. TOC concentrations in small fog drops (<17 microm) were a factor of 3, on average, higher than TOC concentrations in larger drops. As much as half of the dissolved organic matter was determined to have a molecular weight higher than 500 Da. Deposition fluxes of organic matter in fog drops were high (0.5-4.3 microg of C m(-2) min(-1)), indicating the importance of fog processing as a vector for removal of organic matter from the atmosphere. Deposition velocities of organic matter, however, were usually found to be lower than deposition velocities for fogwater, consistent with the enrichment of the organic matter in smaller fog drops with lower terminal settling velocities.

Mechanisms of uranium interactions with hydroxyapatite: Implications for groundwater remediation

USGS Publications Warehouse

Fuller, C.C.; Bargar, J.R.; Davis, J.A.; Piana, M.J.

2002-01-01

The speciation of U(VI) sorbed to synthetic hydroxyapatite was investigated using a combination of U LIII-edge XAS, synchrotron XRD, batch uptake measurements, and SEM-EDS. The mechanisms of U(VI) removal by apatite were determined in order to evaluate the feasibility of apatitebased in-situ permeable reactive barriers (PRBs). In batch U(VI) uptake experiments with synthetic hydroxyapatite (HA), near complete removal of dissolved uranium (>99.5%) to <0.05 ??M was observed over a range of total U(VI) concentrations up to equimolar of the total P in the suspension. XRD and XAS analyses of U(VI)-reacted HA at sorbed concentrations ???4700 ppm U(VI) suggested that uranium(VI) phosphate, hydroxide, and carbonate solids were not present at these concentrations. Fits to EXAFS spectra indicate the presence of Ca neighbors at 3.81 A??. U-Ca separation, suggesting that U(VI) adsorbs to the HA surfaces as an inner-sphere complex. Uranium(VI) phosphate solid phases were not detected in HA with 4700 ppm sorbed U(VI) by backscatter SEM or EDS, in agreement with the surface complexation process. In contrast, U(VI) speciation in samples that exceeded 7000 ppm sorbed U(VI) included a crystalline uranium(VI) phosphate solid phase, identified as chernikovite by XRD. At these higher concentrations, a secondary, uranium(VI) phosphate solid was detected by SEM-EDS, consistent with chernikovite precipitation. Autunite formation occurred at total U:P molar ratios ???0.2. Our findings provide a basis for evaluating U(VI) sorption mechanisms by commercially available natural apatites for use in development of PRBs for groundwater U(VI) remediation.

Popping rocks from the Mid-Atlantic Ridge: Insights into mantle volatile concentrations and degassing dynamics

NASA Astrophysics Data System (ADS)

Jones, M.; Soule, S. A.; Kurz, M. D.; Wanless, V. D.; Le Roux, V.; Klein, F.; Mittelstaedt, E. L.; Curtice, J.

2016-12-01

During a 1985 cruise, the Mid-Atlantic Ridge (MAR) near 14°N yielded an unusually vesicular mid-ocean ridge (MOR) basalt that popped upon recovery from the seafloor due to the release of trapped volatiles. This `popping rock' has been inferred to be representative of primitive, undegassed magmas from the upper mantle due to its high volatile concentrations. Thus, the sample has been used to constrain CO2 flux from the MOR system, upper mantle volatile concentrations, and magma degassing dynamics. However, the lack of geologic context for the original popping rock raises questions about whether it truly reflects the volatile content of its mantle source. Here, we present results from a 2016 cruise to the MAR aimed at characterizing the geologic context of popping rocks and understanding their origins. The newly recovered samples display differences in volatile concentrations and vesicularities between popping and non-popping rocks. These differences may be related to geologic setting and eruption dynamics with potential implications for mantle volatile concentrations. Volatile concentrations in the outer quenched margin of new samples were measured by ion microprobe to elucidate degassing systematics, brine/magma interactions, and popping rock formation. The large variability in dissolved H2O (0.05-0.77 wt%) can be attributed to spatially variable brine contamination. Dissolved CO2 concentrations (153-356 ppm) are likely controlled by initial volatile concentrations and variable degrees of degassing. The subset of popping samples display low dissolved CO2 concentrations (161-178 ppm) and moderate dissolved H2O concentrations (.44-.50 wt%) and are at equilibrium with their eruption depth based on solubility calculations. X-ray microtomography reveals vesicularity in newly collected popping rocks exceeding 19%, making these samples the most highly vesicular recovered from the MAR. The total gas contents in the basaltic glasses are inferred from dissolved volatile concentrations and vesicularity. These calculations are aided by analysis of gas contents in vesicles by confocal Raman spectroscopy and vacuum crushing experiments. The preliminary results and seafloor observations allow an evaluation of the origins of popping rocks and their implications for mantle volatile concentrations.

Tolerance of Oncomelania hupensis quadrasi to varying concentrations of dissolved oxygen and organic pollution*

PubMed Central

Garcia, Rolando G.

1972-01-01

Ecological investigations were made of habitats containing natural populations of the snail Oncomelania hupensis quadrasi and of habitats free from the snail in the island of Leyte, Philippines. This species of snail is a vector of Schistosoma japonicum in the Philippines. Snail-infested habitats had dissolved oxygen levels of 3.8-9.85 ppm but snail-free habitats had levels of only 0.08-3.6 ppm. Snail-infested habitats were less polluted by organic matter than habitats that were snail-free. Larger numbers of chlorophyll-bearing algae were present in both the water and the soil of snail-infested habitats. Other factors, including temperature, pH, hydrogen carbonate alkalinity, and relative humidity, were also investigated. PMID:4538906

Mathematical model simulation of a diesel spill in the Potomac River

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, S.S.; Nicolette, J.P.; Markarian, R.K.

1995-12-31

A mathematical modeling technique was used to simulate the transport and fate of approximately 400,000 gallons of spilled diesel fuel and its impact on the aquatic biota in the Potomac River and Sugarland Run. Sugarland Run is a tributary about 21 miles upstream from Washington, DC. The mass balance model predicted the dynamic (spatial and temporal) distribution of spilled oil. The distributions were presented in terms of surface oil slick and sheen, dissolved and undissolved total petroleum hydrocarbons (TPH) in the water surface, water column, river sediments, shoreline and atmosphere. The processes simulated included advective movement, dispersion, dissolution, evaporation, volatilization,more » sedimentation, shoreline deposition, biodegradation, and removal of oil from cleanup operations. The model predicted that the spill resulted in a water column dissolved TPH concentration range of 0.05 to 18.6 ppm in Sugarland Run. The spilled oil traveled 10 miles along Sugarland Run before it reached the Potomac River. At the Potomac River, the water column TPH concentration was predicted to have decreased to the range of 0.0 to 0.43 ppm. These levels were consistent with field samples. To assess biological injury, the model used 4, 8, 24, 48, and 96-hr LC values in computing the fish injury caused by the fuel oil. The model used the maximum running average of dissolved TPH and exposure time to predict levels of fish mortality in the range of 38 to 40% in Sugarland Run. This prediction was consistent with field fisheries surveys. The model also computed the amount of spilled oil that adsorbed and settled into the river sediments.« less

In situ microcosms to study the impact of heavy metals resuspended by dredging on periphyton in a tropical estuary.

PubMed

Nayar, S; Goh, B P L; Chou, L M; Reddy, S

2003-08-20

Ponggol estuary, located on the northeastern coast of Singapore, is heavily impacted by reclamation, dredging, construction and shipping. Tin, lead, nickel, cadmium, copper and zinc in the particulate and dissolved fraction and in sediments were monitored biweekly in the estuary from July 1999 to June 2000. The concentrations of tin, lead, nickel, cadmium, copper and zinc were observed to range from ND-92 ppm, ND-303 ppm, ND-2818 ppm, ND-74 ppm, ND-1117 ppm and ND-137000 ppm, respectively, in the dissolved, particulate and sediments fractions. Intensive dredging activity occurred during the monitoring period, and this may have led to the resuspension and increased bioavailability of particulate metals. Periphytic algae were established on glass slides and exposed to previously measured environmental levels of heavy metals using in situ estuarine microcosms. The toxicity of heavy metals in various fractions to periphytic algae was assessed from the changes in their chlorophyll a content. Cadmium had the least significant effect followed by lead, zinc, nickel, tin and copper at all concentrations tested. A reduction in periphyton biomass (with respect to controls) of 95-100% was observed for treatments with metals in particulate form. In addition, exposure to contaminated sediments for 3 days significantly decreased chlorophyll a by 90-99% compared to controls. High concentrations of zinc (9893-17240 mg l(-1)), copper (5-11 mg l(-1)) and cadmium (1-1.8 mg l(-1)) recorded in the aqueous phase of treatment microcosms, and attributed to release from the contaminated sediments, could account for the toxicity to periphyton.

Effect of dissolved oxygen on the corrosion behavior of 304 SS in 0.1 N nitric acid containing chloride

NASA Astrophysics Data System (ADS)

Khobragade, Nilay N.; Bansod, Ankur V.; Patil, Awanikumar P.

2018-04-01

A study was undertaken in several selected mixed nitric acid/chloride ({{{{NO}}}3}-/{{{Cl}}}- ratio) electrolytes with the nitric acid concentration of 0.1 N and chloride concentration of 0, 10, 100, 1000 and 10 000 ppm. Electrochemical tests like potentiodynamic polarization test, electrochemical impedance spectroscopy (EIS) and Mott-Schottky analysis (M-S) were carried out when the electrolytes were in deaerated condition and were in open to air (OTA) condition, and the effect of dissolved oxygen was evaluated on the corrosion behavior of 304 SS. It was found that at a critical {{{{NO}}}3}-/{{{Cl}}}- ratio, a passive state is attained at the earliest in OTA condition. Also, the passive film resistance showed higher values in OTA condition than in deaerated condition exhibiting the effect of dissolved oxygen. The results of EIS results confirmed the results obtained by potentiodynamic polarization wherein the low passive current densities were obtained in OTA condition. Mott-Schottky analysis revealed the lowest defect densities in 100 ppm Cl‑ solution in OTA condition and in 10 ppm Cl‑ solution in deaerated condition indicating less defective films formed in these solutions. XPS analysis showed that the film was bilayer in nature in confirmation with M-S analysis. The results were discussed with point defect model (PDM) and by competitive surface adsorption.

A rapid, partial leach and organic separation for the sensitive determination of Ag, Bi, Cd, Cu, Mo, Pb, Sb, and Zn in surface geologic materials by flame atomic absorption

USGS Publications Warehouse

Viets, J.G.; Clark, J.R.; Campbell, W.L.

1984-01-01

A solution of dilute hydrochloric acid, ascorbic acid, and potassium iodide has been found to dissolve weakly bound metals in soils, stream sediments, and oxidized rocks. Silver, Bi, Cd, Cu, Mo, Pb, Sb, and Zn are selectively extracted from this solution by a mixture of Aliquat 336 (tricaprylyl methyl ammonium chloride) and MIBK (methyl isobutyl ketone). Because potentially interfering major and minor elements do not extract, the organic separation allows interference-free determinations of Ag and Cd to the 0.05 ppm level, Mo, Cu, and Zn to 0.5 ppm, and Bi, Pb, and Sb to 1 ppm in the sample using flame atomic absorption spectroscopy. The analytical absorbance values of the organic solution used in the proposed method are generally enhanced more than threefold as compared to aqueous solutions, due to more efficient atomization and burning characteristics. The leaching and extraction procedures are extremely rapid; as many as 100 samples may be analyzed per day, yielding 800 determinations, and the technique is adaptable to field use. The proposed method was compared to total digestion methods for geochemical reference samples as well as soils and stream sediments from mineralized and unmineralized areas. The partial leach showed better anomaly contrasts than did total digestions. Because the proposed method is very rapid and is sensitive to pathfinder elements for several types of ore deposits, it should be useful for reconnaissance surveys for concealed deposits. ?? 1984.

The hydrogeological conditions in Sahel Hasheesh, Eastern Desert, Eg

NASA Astrophysics Data System (ADS)

Abdalla, Mohamed A.; Mekhemer, Hatem M.; Mabrou, Walid Abdallah

2016-06-01

The groundwater development in Egypt in the present time is of a vital importance than in past few years. A comprehensive plan for new land reclamation projects has been recently established. To achieve these plans new sources of water must be available. This has been done by conducting a number of VES'S where interpreted by a comparison with the existing drilled borehole soil samples. The optimum resistivity model is obtained by matching method using "IPI2Win" Moscow State University 2000 software computer programs for resistivity interpretation. The results of the quantitative interpretation of the resistivity curves has been represented as geoelectric sections, showing the thickness and true electric resistivity values of the different geoelectric layers. The results of quantitative interpretation of the vertical electrical soundings show subsurface five geoelectric units and the aquifer system belongs to lower Miocene and the total salinity of 2451.2 ppm. The depth to water surface is 88.05 m and the total dissolved solids are 2451.2 ppm (Mekhemer well). The salt assemblages in Sahel Hasheesh are NaCl, MgCl2, MgSO4, CaSO4, Ca(HCO3)2. This marine water is of brackish sodium chloride water type (NaCl).

THE DETERMINATION OF BORON IN ZIRCALOY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Freegarde, M.; Cartwright, J.

1962-03-01

An account is given of the development of a simple and reliable procedure for determining boron in Zircaloy at the parts per million level. The sample is dissolved in a mixture of bromine and methanol, and the boron is separated by distillation and determined as its rosocyanin complex with curcumin. The reproducibility of the method is characterized by a standard deviation of 0.03 ppm at the 0.3 ppm level. (auth)

Avoidance of selenium-treated food by mallards

USGS Publications Warehouse

Heinz, G.H.; Sanderson, C.J.

1990-01-01

Adult, male mallards (Anas platyrhynchos) were given a choice between a control diet and a diet containing 5, 10 or 20 ppm selenium as selenomethionine dissolved in water and mixed into the diet. At 10 and 20 ppm, selenium-treated diets were avoided. Avoidance appeared to be caused by a conditioned response, probably to illness caused by the selenium and not to an aversion to the taste of the selenium.

Novel Tool for Simultaneous Carbon and Nitrogen Stable Isotope Analyses in Aqueous Samples

NASA Astrophysics Data System (ADS)

Federherr, E.; Schmidt, T. C.; Cerli, C.; Kalbitz, K.; Kupka, H. J.; Lange, L.; Dunsbach, R.; Panetta, R. J.; Kasson, A.

2014-12-01

Investigation of transformation and transport processes of carbon and nitrogen in ecosystems plays an important role to understand and predict their dynamics and role in biogeochemistry. Consequently, suitable and accurate methods for concentration as well as stable isotopic composition analysis of carbon and nitrogen in waters and aqueous solutions play a significant role. Traditionally dissolved carbon and nitrogen stable isotope analysis (SIA) is performed using either offline sample preparation followed by elemental analysis isotope ratio mass spectrometry (EA/IRMS) or modified wet chemical oxidation based device coupled to IRMS. Recently we presented a high temperature combustion system (HTC), which significantly improves upon these methods for dissolved organic carbon (DOC) SIA. The analysis of δ15N of dissolved nitrogen still has large limitations. Its low concentration makes EA/IRMS laborious, time and sample consuming. Systems based on wet chemical oxidation-IRMS bare the risk of sensitivity loss as well as of fractionation due to incomplete mineralization. In addition, the high solubility of molecular nitrogen in water remains a technical challenge, as it requires additional separation steps to distinguish between physically dissolved nitrogen and bound nitrogen. Further development of our HTC system lead to the implementation of the δ15N determination which now coupled, into a novel total organic carbon (TOC) analyzing system, especially designed for SIA of both, carbon and nitrogen. Integrated, innovative purge and trap technique (peak focusing) for nitrogen with aluminosilicate adsorber and peltier element based cooling system, in combination with high injection volume (up to 3 mL) as well as favorable carrier gas flow significantly improves sensitivity. Down to 1ppm and less total nitrogen can be measured with precision of ≤ 0.5‰. To lower the background caused by physically dissolved nitrogen new, membrane-vacuum based, degasser was designed for online separation of physically dissolved nitrogen. This novel HTC system, "iso TOC cube", provides an innovative tool with large potential in investigation of biogeochemical carbon and nitrogen cycles.

SPECTROPHOTOMETRIC DETERMINATION OF TRACES OF BORON IN THORIUM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Onishi, H.; Ishiwatari, N.; Nagai, H.

1960-12-01

A procedure is described for the spectrophotometric determination of a few tenths of a pant per million of boron ia thorium oxide or thorium. The sample is dissolved in strong phosphoric acid. After diluting the solution with water, boron is separated by distillation as methyl borate and finally determined by the curcumin method. The error is not likely to exceed plus or minus O.l ppm for 0.2 to 1 ppm of boron. (auth)

Effects of pH2O, pH2 and fO2 on the Diffusion of H-Bearing Species in Lunar Basalt and an Iron-Free Basaltic Analog at 1 atm

NASA Astrophysics Data System (ADS)

Newcombe, M. E.; Beckett, J. R.; Baker, M. B.; Newman, S.; Guan, Y.; Eiler, J. M.; Stolper, E. M.

2016-12-01

We have conducted water diffusion experiments in synthetic Apollo 15 "yellow glass" (LG) and an iron-free basaltic analog melt (AD) at 1 atm and 1350 °C over a range of fO2 conditions from IW-2.2 to IW+6.7 and over a range of pH2/pH2O from nominally zero to 10. The water concentrations measured in our quenched experimental glasses by SIMS and FTIR vary from a few ppm to 430 ppm. Many studies of water diffusion at higher water concentrations indicate that the apparent diffusivity of total water (D*water; see [1]) in silicate melts is highly concentration dependent at water contents >0.1 wt% (e.g., [1]). However, water concentration gradients in each of our AD and LG experiments are well described by models in which D*water is assumed to be constant. Best-fit values of D*water obtained for our AD and LG experiments are consistent with a modified speciation model [2] in which both molecular water and hydroxyl are allowed to diffuse, and in which hydroxyl is the dominant diffusing species at the low total water concentrations of our experiments. Water concentration gradients generated during hydration and dehydration experiments conducted simultaneously propagate approximately equal distances into the melt and have the same concentration of water dissolved in the melt at the melt-vapor interface, suggesting that hydration and dehydration are symmetric under the conditions of our experiments. Best-fit values of D*water for our LG experiments vary within a factor of 2 over a range of pH2/pH2O from 0.007 to 9.7 (a range of ƒO2 from IW-2.2 to IW+4.9) and a water concentration range from 80 ppm to 280 ppm. The relative insensitivity of D*water to variations in pH2 suggests that loss of H during the degassing of the lunar melts described by [3] was not primarily by loss of dissolved H2. The value of D*water chosen by [3] for modeling diffusive degassing of lunar volcanic glasses is within a factor of three of our measured value in LG melt at 1350 °C. [1] Zhang et al. (1991) GCA 55, 441-456; [2] Ni et al. (2013) GCA 103, 36-48; [3] Saal et al. (2008) Nature 454, 192-195.

Olivine-hosted Melt Inclusions: Insights into Highly Explosive Basaltic Volcanism from Alkali-rich Magma at Sunset Crater, AZ

NASA Astrophysics Data System (ADS)

Allison, C. M.; Roggensack, K.; Clarke, A. B.

2017-12-01

Sunset Crater volcano, an alkali basalt scoria cone in northern Arizona, erupted ca. 1085 AD, producing a large tephra blanket through sub-Plinian activity during its most explosive period. Primary melt inclusions (MIs) in free olivine crystals from the tephra were analyzed to study magma characteristics and storage conditions. We compare MIs from the early-erupted Strombolian deposit to those of sub-Plinian units to identify magma properties related to eruptive style. All MIs are faceted and closely similar in composition exhibiting minor post entrapment crystallization (3-15%). MIs are relatively dry (0.5-1.5 wt% H2O) but CO2-rich (1,200-3000 ppm). Most MIs contain >1 wt% H2O and >2,000 ppm CO2. MI vapor bubbles are ubiquitous in Sunset Crater samples ranging in size from 1 to 10 vol% of the MI in typical samples or 3 vol% on average. However, based on MI shrinkage caused by the decrease of olivine and melt densities with lower temperatures, only bubbles smaller than 3 vol% can result from post-entrapment cooling alone. We conclude that larger MI bubbles likely include volume contributions from pre-entrapment vapor. Raman spectroscopy, calibrated with synthetic CO2 inclusions, shows that the bubbles contain CO2 vapor and carbonate crystals have been observed on the bubble walls. Total MI CO2 contents, representing dissolved CO2 plus vapor bubble (if less than 3 vol% in size), range up to 4500 ppm. If no size constraint is applied to the vapor bubbles, the maximum total CO2 content (dissolved + vapor) reaches 6,500 ppm. These volatile abundances exceed the current experimental data on volatile solubility in alkali basalts. Fluid-saturated H2O-CO2 solubility experiments at 1200 °C between 400 and 600 MPa were conducted on the bulk Sunset Crater composition to account for the enhanced CO2 solubility of alkali-rich magma and accurately constrain solubility. This experimental data and the resulting calibrated thermodynamic model, indicates that MIs record depths up to 17 km, assuming fluid saturation. We do not observe any significant differences between MIs from Strombolian and sub-Plinian phases, suggesting that while a high CO2 content may drive rapid magma ascent and be partly responsible for highly explosive eruptions, shallower processes may play an important role in the final eruptive character.

Mid-Infrared Spectroscopic Method for the Identification and Quantification of Dissolved Oil Components in Marine Environments.

PubMed

Stach, Robert; Pejcic, Bobby; Crooke, Emma; Myers, Matthew; Mizaikoff, Boris

2015-12-15

The use of mid-infrared sensors based on conventional spectroscopic equipment for oil spill monitoring and fingerprinting in aqueous systems has to date been mainly confined to laboratory environments. This paper presents a portable-based mid-infrared attenuated total reflectance (MIR-ATR) sensor system that was used to quantify a number of environmentally relevant hydrocarbon contaminants in marine water. The sensor comprises a polymer-coated diamond waveguide in combination with a room-temperature operated pyroelectric detector, and the analytical performance was optimized by evaluating the influence of polymer composition, polymer film thickness, and solution flow rate on the sensor response. Uncertainties regarding the analytical performance and instrument specifications for dissolved oil detection were investigated using real-world seawater matrices. The reliability of the sensor was tested by exposition to known volumes of different oils; crude oil and diesel samples were equilibrated with seawater and then analyzed using the developed MIR-ATR sensor system. For validation, gas chromatographic measurements were performed revealing that the MIR-ATR sensor is a promising on-site monitoring tool for determining the concentration of a range of dissolved oil components in seawater at ppb to ppm levels.

Optimized alumina coagulants for water treatment

DOEpatents

Nyman, May D [Albuquerque, NM; Stewart, Thomas A [Albuquerque, NM

2012-02-21

Substitution of a single Ga-atom or single Ge-atom (GaAl.sub.12 and GeAl.sub.12 respectively) into the center of an aluminum Keggin polycation (Al.sub.13) produces an optimal water-treatment product for neutralization and coagulation of anionic contaminants in water. GaAl.sub.12 consistently shows .about.1 order of magnitude increase in pathogen reduction, compared to Al.sub.13. At a concentration of 2 ppm, GaAl.sub.12 performs equivalently to 40 ppm alum, removing .about.90% of the dissolved organic material. The substituted GaAl.sub.12 product also offers extended shelf-life and consistent performance. We also synthesized a related polyaluminum chloride compound made of pre-hydrolyzed dissolved alumina clusters of [GaO.sub.4Al.sub.12(OH).sub.24(H.sub.2O).sub.12].sup.7+.

The solubility of sulfur in high-TiO2 mare basalts

NASA Technical Reports Server (NTRS)

Danckwerth, P. A.; Hess, P. C.; Rutherford, M. J.

1979-01-01

The present paper deals with an experimental investigation of the solubility of sulfur of the high-TiO2 mare basalt 74275 at 1 atm, 1250 C. The data indicate that at saturation, 74275 is capable of dissolving 3400 ppm sulfur at 10 to 15 degrees below its liquidus. The analyzed samples of 74275 show sulfur contents of 1650 ppm S, which indicates that 74275 was 50% undersaturated at the time of eruption.

Arsenic Incorporation Into Authigenic Pyrite, Bengal Basin Sediment, Bangladesh

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowers, H.A.; Breit, G.N.; Foster, A.L.

2007-07-10

Sediment from two deep boreholes ({approx}400 m) approximately 90 km apart in southern Bangladesh was analyzed by X-ray absorption spectroscopy (XAS), total chemical analyses, chemical extractions, and electron probe microanalysis to establish the importance of authigenic pyrite as a sink for arsenic in the Bengal Basin. Authigenic framboidal and massive pyrite (median values 1500 and 3200 ppm As, respectively), is the principal arsenic residence in sediment from both boreholes. Although pyrite is dominant, ferric oxyhydroxides and secondary iron phases contain a large fraction of the sediment-bound arsenic between approximately 20 and 100 m, which is the depth range of wellsmore » containing the greatest amount of dissolved arsenic. The lack of pyrite in this interval is attributed to rapid sediment deposition and a low sulfur flux from riverine and atmospheric sources. The ability of deeper aquifers (>150 m) to produce ground water with low dissolved arsenic in southern Bangladesh reflects adequate sulfur supplies and sufficient time to redistribute the arsenic into pyrite during diagenesis.« less

Arsenic incorporation into authigenic pyrite, Bengal Basin sediment, Bangladesh

USGS Publications Warehouse

Lowers, H.A.; Breit, G.N.; Foster, A.L.; Whitney, J.; Yount, J.; Uddin, Md. N.; Muneem, Ad. A.

2007-01-01

Sediment from two deep boreholes (???400 m) approximately 90 km apart in southern Bangladesh was analyzed by X-ray absorption spectroscopy (XAS), total chemical analyses, chemical extractions, and electron probe microanalysis to establish the importance of authigenic pyrite as a sink for arsenic in the Bengal Basin. Authigenic framboidal and massive pyrite (median values 1500 and 3200 ppm As, respectively), is the principal arsenic residence in sediment from both boreholes. Although pyrite is dominant, ferric oxyhydroxides and secondary iron phases contain a large fraction of the sediment-bound arsenic between approximately 20 and 100 m, which is the depth range of wells containing the greatest amount of dissolved arsenic. The lack of pyrite in this interval is attributed to rapid sediment deposition and a low sulfur flux from riverine and atmospheric sources. The ability of deeper aquifers (>150 m) to produce ground water with low dissolved arsenic in southern Bangladesh reflects adequate sulfur supplies and sufficient time to redistribute the arsenic into pyrite during diagenesis.

Volatile Concentrations in Pyroclastic Obsidian: Two Case Studies

NASA Astrophysics Data System (ADS)

Wearn, K. M.; Cashman, K. V.; Wallace, P. J.

2002-12-01

Pyroclastic obsidian is abundant in fall deposits associated with Mt. Mazama's Cleetwood eruption and South Sister's Rock Mesa eruption. Measured concentrations of H2Ototal and CO2 in >300 obsidian samples from these two eruptions provide important information about both the style of degassing (open- vs. closed-system) and changes in eruptive conditions through the course of both eruptions. Obsidian clasts preserve a range of total H2O contents, with samples from lower stratigraphic levels displaying a wider range of water concentrations than those from the uppermost tephra layer sampled. All samples from the Cleetwood section contain <=1 wt% water, with those from the top of that deposit containing <0.4 wt%. Obsidian from the basal ash layer of the subsequent climactic eruption contains 0.1 - 0.8 wt% water. Obsidian fragments from the Rock Mesa eruption show a broader range in H2Ototal contents (from 0.1 to >3 wt%) than those from the Cleetwood eruption. At Rock Mesa, maximum total water contents generally decrease with increased stratigraphic height. However, this decrease is not strictly monotonic: fluctuations in maximum total water contents correspond to stratigraphic unit boundaries. In addition, the Rock Mesa event produced abundant obsidian with very low H2Ototal concentrations throughout the eruption. Dissolved molecular CO2 levels are below the detection limit in all of the Cleetwood and Mazama samples. This is not surprising, given the low initial CO2 measured in Cleetwood and Mazama melt inclusions by Bacon et al. (1992). CO2 concentrations in the Rock Mesa clasts range from <5 ppm to ~44 ppm, and are positively correlated with H2Ototal concentrations. Fluorine concentrations in Cleetwood and Mazama climactic obsidian clasts vary between ~510 and ~695 ppm, with climactic samples averaging slightly lower concentrations than Cleetwood samples. Fluorine concentrations in Rock Mesa obsidians are uniformly low (~300 to ~510 ppm). Chlorine contents of Cleetwood and Mazama climactic samples range from ~1400 ppm to ~1610 ppm. The Rock Mesa samples all contain less chlorine (~510 to ~1120 ppm) than the Cleetwood and climactic samples, and in the Rock Mesa obsidian, chlorine and total water are positively correlated. Stratigraphic variations in the volatile contents of pyroclastic obsidian support previous work suggesting that obsidian forms along the margins of the volcanic conduit and is eroded from the conduit walls by fragmenting magma. Both the Cleetwood and the Rock Mesa deposits indicate initial evacuation of shallow vanguard magma followed by a rapid increase in fragmentation depth. Both deposits also show a gradual decrease in the fragmentation depth through time, consistent with subsequent effusive activity in both cases. More puzzling is the apparent closed-system degassing trend defined by the H2O-CO2-Cl relations in the Rock Mesa obsidian samples, despite the loss of volatiles required for obsidian formation. This suggests that volatile data may also provide information on the relative time scales of volatile exsolution and loss and obsidian formation.

Stormwater Effects on Heavy Metal Sequestration in a Bioretention System in Culver City, California

NASA Astrophysics Data System (ADS)

Yousavich, D. J.; Ellis, A. S.; Dorsey, J.; Johnston, K.

2017-12-01

Rain Gardens, also referred to as bioretention or biofilters, are often used to capture or filter urban runoff before it drains into surface or groundwater systems. The Culver City Rain Garden (CCRG) is one such system that is designed to capture and filter runoff from approximately 11 acres of mixed-use commercial and industrial land before it enters Ballona Creek. The EPA has designated Ballona Creek as an impaired waterway and established Total Maximum Daily Loads for heavy metals. Previous research has utilized sequential extractions to establish trends in heavy metal sequestration for Cu, Pb, and Zn in bioretention media. The aim of this project is to evaluate if there is a difference in heavy metal sequestration between dry and wetted bioretention media. To characterize the stormwater at the site, influent and surface water were collected and analyzed for sulfate and heavy metals 3 times during the 2016-2017 storm season. Two soil cores from the CCRG were acquired in the summer of 2017 to analyze soil metal sequestration trends. They will be subjected to different wetting conditions, sectioned into discrete depths, and digested with an established sequential extraction technique. Surface water in the CCRG shows average Dissolved Oxygen during wet conditions of 2.92 mg/L and average pH of 6.1 indicating reducing conditions near the surface and the possible protonation of adsorption sites during wet weather conditions. Influent metal data indicate average dissolved iron levels near 1 ppm and influent Cu, Pb, and Zn levels near 0.05, 0.01, and 0.5 ppm respectively. This coupled with average surface water sulfate levels near 3 ppm indicates the potential for iron oxide and sulfide mineral formation depending on redox conditions. The sequential extraction results will elucidate whether heavy metals are adsorbed or are being sequestered in mineral formation. These results will allow for the inclusion of heavy metal sequestration trends in the design of further bioretention projects and maintenance of current sites.

Reconnaissance of the chemical quality of surface waters of the Neches River basin, Texas

USGS Publications Warehouse

Hughes, Leon S.; Leifeste, Donald K.

1967-01-01

The kinds and quantities of minerals dissolved in the surface water of the Neches River basin result from such environmental factors as geology, streamflow patterns and characteristics, and industrial influences. As a result of high rainfall in the basin, much of the readily soluble material has been leached from the surface rocks and soils. Consequently, the water in the streams is usually low in concentrations of dissolved minerals and meets the U.S. Public Health Service drinking-water standards. In most streams the concentration of dissolved solids is less than 250 ppm (parts per million). The Neches River drains an area of about 10,000 square miles in eastern Texas. From its source in southeast Van Zandt County the river flows in a general southeasterly direction and empties into Sabine Lake, an arm of the Gulf of Mexico. In the basin the climate ranges from moist subhumid to humid, and the average annual rainfall ranges from 46 inches is the northwest to more than 52 inches in the southeast. Annual runoff from the basin has averaged 11 inches; however, runoff rates vary widely from year to year. The yearly mean discharge of the Neches River at Evadale has ranged from 994 to 12,720 cubic feet per second. The rocks exposed in the Neches River basin are of the Quaternary and Tertiary Systems and range in age from Eocene to Recent. Throughout most of the basin the geologic formations dip generally south and southeast toward the gulf coast. The rate of dip is greater than that of the land surface; and as a result, the older formations crop out to the north of the younger formations. Water from the outcrop areas of the Wilcox Group and from the older formations of the Claiborne Group generally has dissolved-solids concentrations ranging from 100 to 250 ppm; water from the younger formations has concentrations less than 100 ppm. The northern half of the basin has soft water, with less than 60 ppm hardness. The southern half of .the basin has very soft water, usually with less than 30 ppm hardness. The chloride concentrations are less than 20 ppm in surface water in the southern half of the basin and usually range from 20 to 100 ppm in the northern half of the basin. Concentrations greater than 100 ppm are found only where pollution is occurring. The Neches River basin has an abundance of surface water, but uneven distribution of runoff makes storage projects necessary to provide dependable water supplies. The principal existing reservoirs, with the exception of Striker Creek Reservoir, contain water of excellent quality. Chemical-quality data for the Striker Creek drainage area indicate that its streams are affected by .the disposal of brines associated with oil production. Sam Rayburn Reservoir began impounding water in 1965. The water impounded should prove of acceptable quality for most uses, but municipal and industrial wastes released into the Angelina River near Lufkin may have a degrading effect on the quality of the water, especially during extended periods of low flows. Water available for storage at the many potential reservoir sites will be of good quality; but, if the proposed salt-water barrier is to impound acceptable water, the disposal of oilfield brine into Pine Island Bayou should be discontinued.

129Xe NMR chemical shift in Xe@C60 calculated at experimental conditions: essential role of the relativity, dynamics, and explicit solvent.

PubMed

Standara, Stanislav; Kulhánek, Petr; Marek, Radek; Straka, Michal

2013-08-15

The isotropic (129)Xe nuclear magnetic resonance (NMR) chemical shift (CS) in Xe@C60 dissolved in liquid benzene was calculated by piecewise approximation to faithfully simulate the experimental conditions and to evaluate the role of different physical factors influencing the (129)Xe NMR CS. The (129)Xe shielding constant was obtained by averaging the (129)Xe nuclear magnetic shieldings calculated for snapshots obtained from the molecular dynamics trajectory of the Xe@C60 system embedded in a periodic box of benzene molecules. Relativistic corrections were added at the Breit-Pauli perturbation theory (BPPT) level, included the solvent, and were dynamically averaged. It is demonstrated that the contribution of internal dynamics of the Xe@C60 system represents about 8% of the total nonrelativistic NMR CS, whereas the effects of dynamical solvent add another 8%. The dynamically averaged relativistic effects contribute by 9% to the total calculated (129)Xe NMR CS. The final theoretical value of 172.7 ppm corresponds well to the experimental (129)Xe CS of 179.2 ppm and lies within the estimated errors of the model. The presented computational protocol serves as a prototype for calculations of (129)Xe NMR parameters in different Xe atom guest-host systems. Copyright © 2013 Wiley Periodicals, Inc.

Fiber optic gas detection system for health monitoring of oil-filled transformer

NASA Astrophysics Data System (ADS)

Ho, H. L.; Ju, J.; Jin, W.

2009-10-01

This paper reports the development of a fiber-optic gas detection system capable of detecting three types of dissolved fault gases in oil-filled power transformers or equipment. The system is based on absorption spectroscopy and the target gases include acetylene (C2H2), methane (CH4) and ethylene (C2H4). Low-cost multi-pass sensor heads using fiber coupled micro-optic cells are employed for which the interaction length is up to 4m. Also, reference gas cells made of photonic bandgap (PBG) fiber are implemented. The minimum detectable gas concentrations for methane, acetylene and ethylene are 5ppm, 2ppm and 50ppm respectively.

Special Polymer/Carbon Composite Films for Detecting SO2

NASA Technical Reports Server (NTRS)

Homer, Margie; Ryan, Margaret; Yen, Shiao-Pin; Kisor, Adam; Jewell, April; Shevade, Abhijit; Manatt, Kenneth; Taylor, Charles; Blanco, Mario; Goddard, William

2008-01-01

A family of polymer/carbon films has been developed for use as sensory films in electronic noses for detecting SO2 gas at concentrations as low as 1 part per million (ppm). Most previously reported SO2 sensors cannot detect SO2 at concentrations below tens of ppm; only a few can detect SO2 at 1 ppm. Most of the sensory materials used in those sensors (especially inorganic ones that include solid oxide electrolytes, metal oxides, and cadmium sulfide) must be used under relatively harsh conditions that include operation and regeneration at temperatures greater than 100 C. In contrast, the present films can be used to detect 1 ppm of SO2 at typical opening temperatures between 28 and 32 C and can be regenerated at temperatures between 36 and 40 C. The basic concept of making sensing films from polymer/carbon composites is not new. The novelty of the present family of polymer/carbon composites lies in formulating the polymer components of these composites specifically to optimize their properties for detecting SO2. First-principles quantum-mechanical calculations of the energies of binding of SO2 molecules to various polymer functionalities are used as a guide for selecting polymers and understanding the role of polymer functionalities in sensing. The polymer used in the polymer-carbon composite is a copolymer of styrene derivative units with vinyl pyridine or substituted vinyl pyridine derivative units. To make a substituted vinyl pyridine for use in synthesizing such a polymer, poly(2-vinyl pyridine) that has been dissolved in methanol is reacted with 3-chloropropylamine that has been dissolved in a solution of methanol. The methanol is then removed to obtain the copolymer. Later, the copolymer can be dissolved in an appropriate solvent with a suspension of carbon black to obtain a mixture that can be cast and then dried to obtain a sensory film.

Geology and ground water of the Luke area, Maricopa County, Arizona

USGS Publications Warehouse

Stulik, Ronald S.; Twenter, F.R.

1964-01-01

Luke Air Force Base, in the Salt River Valley in central Arizona. is within an intermontane basin--the Phoenix basin--in the Basin and Range lowlands province. The Luke area, the subject of this study, extends beyond the limits of the base. Ground-water resources of the Luke area were studied to determine the possibility of developing a water supply of optimum quantity and quality to supplement the base supply. Several wells drilled for this purpose, prior to the study, either produced an inadequate supply of water or produced ware-that had a high dissolved-solids content. The Phoenix basin is filled with unconsolidated to semiconsolidated Tertiary and Quaternary sedimentary rocks that are referred to as valley fill. Although its total thickness is unknown, 2,784 feet of valley fill--primarily consisting of clay, silt, sand, and gravel--has been penetrated. Percentage-distribution maps of fine-grained materials indicate a gross-facies pattern and a selective depositional area of the valley-fill materials. The maps also indicate that the areal distribution of fine-grained materials increases with depth. In general, the better producing wells, regardless of depth, are in areas where tee valley fill is composed of less than 60 percent fine-grained materials. The water table in the area is declining because large quantities of water are withdrawn and recharge is negligible. The decline near Luke Air Force Base during the period 1941-61 was about 150 feet. Ground water was moving generally southwest in the spring of 1961. Locally, changes in the direction of movement indicate diversion toward two major depressions. The dissolved-solids content of the ground water ranged from about 190 to 6,300 ppm. The highest concentration of dissolved solids is in water from the southern part of the area and seems to come from relatively shallow depths; wells in the northern part generally yield water of good quality. After a reconnaissance of the area, the U.S. Geological Survey located and supervised the drilling of two test wells--wells (B-2-1) 9bcb and (B-2-1) 5abc?on Luke Air Force Base. The quantity of water produced by the wells was adequate. The dissolved-solids content of water from the wells was low, and the overall quality of water from well (B-2-1) 5abc was good. When well (B-2-1) 9bcb was perforated between 907 and 977 feet, the water had a fluoride concentration of 4.4 ppm; however, the fluoride concentration decreased to 2.8 ppm when new perforations were cut at a shallower depth, and it was decided that dilution with other base water supplies probably would alleviate any possible fluoride problem.

Effect of atmospheric pressure dielectric barrier discharge plasma on the biological activity of naringin.

PubMed

Kim, Hyun-Joo; Yong, Hae In; Park, Sanghoo; Kim, Kijung; Kim, Tae Hoon; Choe, Wonho; Jo, Cheorun

2014-10-01

The biological activity of naringin treated with atmospheric pressure plasma was evaluated to investigate whether exposure to plasma can be used as a method to improve the biological activity of natural materials. Naringin was dissolved in methanol (at 500 ppm) and transferred to a container. A dielectric barrier discharge (DBD) (250 W, 15 kHz, ambient air) was then generated. Treatment with the plasma for 20 min increased the radical-scavenging activity, FRAP value, and the total phenolic compound content of naringin from 1.45% to 38.20%, from 27.78 to 207.78 μM/g, and from 172.50 to 225.83 ppm, respectively. Moreover, the tyrosinase-inhibition effect of naringin increased from 6.12% to 83.30% upon plasma treatment. Naringin treated with plasma exhibited antimicrobial activity against foodborne pathogens, especially Salmonella Typhimurium; an activity that was absent before plasma treatment. Structural modifications induced in the naringin molecule by plasma might be responsible for improving the biological activity of naringin. Copyright © 2014 Elsevier Ltd. All rights reserved.

Determination of arsenic, antimony, bismuth, cadmium, copper, lead, molybdenum, silver and zinc in geological materials by atomic-absorption spectrometry

USGS Publications Warehouse

Viets, J.G.; O'Leary, R. M.; Clark, Robert J.

1984-01-01

Arsenic, antimony, bismuth, cadmium, copper, lead, molybdenum, silver and zinc are very useful elements in geochemical exploration. In the proposed method, geological samples are fused with potassium pyrosulphate and the fusate is dissolved in a solution of hydrochloric acid, ascorbic acid and potassium iodide. When this solution is shaken with a 10% V/V Aliquat 336 - isobutyl methyl ketone organic phase, the nine elements of interest are selectively partitioned in the organic phase. All nine elements can then be determined in the organic phase using flame atomic-absorption spectrometry. The method is rapid and allows the determination of Ag and Cd at levels down to 0.1 p.p.m., Cu, Mo, and Zn down to 0.5 p.p.m., Pb, Bi and Sb down to 1 p.p.m. and As down to 5 p.p.m. in geological materials.

Physicochemical and Antioxidant Properties of Honeys from the Sundarbans Mangrove Forest of Bangladesh

PubMed Central

Islam, M Rabiul; Pervin, Tahmina; Hossain, Hemayet; Saha, Badhan; Hossain, Sheikh Julfikar

2017-01-01

This study evaluated the physicochemical, nutritional, antioxidant, and phenolic properties of ten honey samples from the Sundarbans mangrove forest, Bangladesh. The average pH, electrical conductivity, total dissolved solid, ash, moisture, hydroxymethyl furfural, titrable acidity, and absorbance were 4.3, 0.38 mS/cm, 187.5 ppm, 0.14%, 17.88%, 4.4 mg/kg, 37.7 meq/kg, and 483 mAU, respectively. In the honeys, the average contents of Ca, Cu, Fe, K, Mg, Mn, and Na were 95.5, 0.19, 6.4, 302, 39.9, 3.4, and 597 ppm, respectively, whereas Cd, Cr, Pb, and Ni were not found. The average contents of total sugar, protein, lipid, vitamin C, polyphenols, flavonoids, and anthocyanins in the honeys were 69.3%, 0.8%, 0.29%, 107.3 mg/kg, 757.2 mg gallic acid equivalent/kg, 43.1 mg chatechin equivalent/kg, and 5.4 mg/kg, respectively. The honeys had strong 1,1-diphenyl-2-picrylhydrazyl free radical scavenging activity, reducing power and total antioxidant capacity. High-performance liquid chromatography analysis of the honey fractions revealed the quantification of six polyphenols namely, (+)-catechin, (−)-epicatechin, p-caumeric acid, syringic acid, trans-cinnamic acid, and vanillic acid at 194.98, 330.34, 74.64, 218.97, 49.55, and 118.84 mg/kg, respectively. Therefore, the honeys in the Sundarbans are of excellent quality and a prospective source of polyphenols, and antioxidants. PMID:29333387

Physicochemical and Antioxidant Properties of Honeys from the Sundarbans Mangrove Forest of Bangladesh.

PubMed

Islam, M Rabiul; Pervin, Tahmina; Hossain, Hemayet; Saha, Badhan; Hossain, Sheikh Julfikar

2017-12-01

This study evaluated the physicochemical, nutritional, antioxidant, and phenolic properties of ten honey samples from the Sundarbans mangrove forest, Bangladesh. The average pH, electrical conductivity, total dissolved solid, ash, moisture, hydroxymethyl furfural, titrable acidity, and absorbance were 4.3, 0.38 mS/cm, 187.5 ppm, 0.14%, 17.88%, 4.4 mg/kg, 37.7 meq/kg, and 483 mAU, respectively. In the honeys, the average contents of Ca, Cu, Fe, K, Mg, Mn, and Na were 95.5, 0.19, 6.4, 302, 39.9, 3.4, and 597 ppm, respectively, whereas Cd, Cr, Pb, and Ni were not found. The average contents of total sugar, protein, lipid, vitamin C, polyphenols, flavonoids, and anthocyanins in the honeys were 69.3%, 0.8%, 0.29%, 107.3 mg/kg, 757.2 mg gallic acid equivalent/kg, 43.1 mg chatechin equivalent/kg, and 5.4 mg/kg, respectively. The honeys had strong 1,1-diphenyl-2-picrylhydrazyl free radical scavenging activity, reducing power and total antioxidant capacity. High-performance liquid chromatography analysis of the honey fractions revealed the quantification of six polyphenols namely, (+)-catechin, (-)-epicatechin, p -caumeric acid, syringic acid, trans -cinnamic acid, and vanillic acid at 194.98, 330.34, 74.64, 218.97, 49.55, and 118.84 mg/kg, respectively. Therefore, the honeys in the Sundarbans are of excellent quality and a prospective source of polyphenols, and antioxidants.

The assessment of treated wastewater quality and the effects of mid-term irrigation on soil physical and chemical properties (case study: Bandargaz-treated wastewater)

NASA Astrophysics Data System (ADS)

Kaboosi, Kami

2017-09-01

This study was conducted to investigate the characteristics of inflow and outflow wastewater of the Bandargaz wastewater treatment plant on the basis of the data collection of operation period and the samples taken during the study. Also the effects of mid-term use of the wastewater for irrigation (from 2005 to 2013) on soil physical and chemical characteristics were studied. For this purpose, 4 samples were taken from the inflow and outflow wastewater and 25 quality parameters were measured. Also, the four soil samples from a depth of 0-30 cm of two rice field irrigated with wastewater in the beginning and middle of the planting season and two samples from one adjacent rice field irrigated with fresh water were collected and their chemical and physical characteristics were determined. Average of electrical conductivity, total dissolved solids, sodium adsorption ratio, chemical oxygen demand and 5 days biochemical oxygen demand in treated wastewater were 1.35 dS/m, 707 ppm, 0.93, 80 ppm and 40 ppm, respectively. Results showed that although some restrictions exist about chlorine and bicarbonate, the treated wastewater is suitable for irrigation based on national and international standards and criteria. In comparison with fresh water, the mid-term use of wastewater caused a little increase of soil salinity. However, it did not lead to increase of soil salinity beyond rice salinity threshold. Also, there were no restrictions on soil in the aspect of salinity and sodium hazard on the basis of many irrigated soil classifications. In comparison with fresh water, the mid-term use of wastewater caused the increase of total N, absorbable P and absorbable K in soil due to high concentration of those elements in treated wastewater.

Surface and Ground Water Quality in Köprüören Basin (Kütahya), Turkey

NASA Astrophysics Data System (ADS)

Arslan, Şebnem; Çelik, Mehmet; Erdem Dokuz, Uǧur; Abadi Berhe, Berihu

2014-05-01

In this study, quality of the water resources in Köprüören Basin, located to the west of Kütahya city in western Anatolia, were investigated. The total catchment area of the basin is 275 km2 and it is located upstream of Kütahya and Eskişehir plains. Therefore, besides 6,000 people residing in the basin, a much larger population will be impacted by the quality of surface and groundwater resources. Groundwater occurs under confined conditions in the limestones of Pliocene units. Groundwater flow is from north to south and south to north towards Kocasu stream, which flows to Enne Dam. The surface and ground water quality in this area are negatively affected by the mining activities. In the northern part of the area, there are coal deposits present in Miocene Tunçbilek formation. Ground waters in contact with the coal deposits contain low concentrations of arsenic (up to 30 µg/l). In the southern part, the only silver deposit of Turkey is present, which is developed in metamorphic basement rocks, Early Miocene volcanics and Pliocene units near Gümüşköy (Gümüş means silver, köy means village in Turkish). The amount of silver manufactured annually in this silver plant is huge and comprises about 1% of the World's Silver Production. The wastes, enriched in cyanide, arsenic, stibnite, lead and zinc, are stored in waste pools and there is extensive leakage of these heavy metals from these pools. Therefore, surface waters, soils and plants in the affected areas contain high concentrations of arsenic, stibnite and lead. The As, Sb, Pb and Zn concentrations are up to 733 µg/l, 158 µg/l, 48 µg/l, and 286 µg/l in surface waters (in dry season), 6180 ppm, 410 ppm, 4180 ppm, 9950 ppm in soils and 809 ppm, 399 ppm, 800 ppm, 2217 ppm in plants, respectively. Today, most of the As, Sb, Pb and Zn are absorbed by the soils and only a small part are dissolved in water. However, conditions might change in future leading to desorption of these contaminants. Therefore, necessary precautions should be undertaken immediately to protect the environment in the area.

Fuel Cell System Contaminants Material Screening Data: Text Version |

Science.gov Websites

explore the results of fuel cell system contaminants studies. Total Anions [IC] and Total Concentration of Elements [ICP] in Leachate Solutions Material Class Manufacturer Trade Name and Use Grade ICP Total (ppm ) IC Total (ppm) Total Organic Carbon (ppm) Solution Conductivity (µS/cm) Adhesives LORD 2-part

Triacetin as food additive in gummy candy and other foodstuffs on the market.

PubMed

Ogawa, T; Moriwaki, N; Fujii, R; Tanaka, K; Mori, E; Saitou, M; Yoshizawa, H; Sakaguchi, H

1992-04-01

The qualitative and quantitative analytical methods were proposed for the simple and rapid determination of triacetin (TAc) in commercial gummy candies and other foodstuffs by gas chromatography (GC), thin layer chromatography (TLC) and infrared spectroscopy (IR). Each extract from the samples was obtained by pretreatment of the foodstuffs as follows: (A) Gummy candy was dissolved in warm water and the solution was extracted with chloroform. The organic (chloroform) layer was separated. (B) Samples (such as ice cream) containing substantial water were mixed with anhydrous Na2SO4 and stirred to sandy appearance and dried. The residue was homogenized with ether, followed by centrifuging, and the organic (ether) layer was separated. (C) Dried samples (such as chocolate and cookie) were smashed, homogenized with ether, and followed by centrifuging, and the organic (ether) layer was separated. (D) Candy was dissolved in warm water and the solution was extracted with ether. The organic (ether) layer was separated. Each organic layer from (A)-(D) was washed with 10% NaHCO3 and evaporated. The residue containing TAc was dissolved in dichloromethane. The extract obtained was subjected to column chromatography on silica gel. The fractions containing TAc were employed in GC with 25% PEG-20M column, TLC, and IR analyses. Recovery of TAc from gummy candy was 99.1 +/- 3.0% and those from other foodstuffs ranged from was 82.1 to 99.4% by GC. Detection limit by this method was 10 ppm. TAc was found to contain at a level as high as 550 ppm in one domestic gummy candy. On the other hand, one imported gummy candy contained no more than 20 ppm of TAc gummy candy.

Secondary ferroan dolomite rhombs in oil reservoirs, Chadra Sands, Gialo field, Libya

DOE Office of Scientific and Technical Information (OSTI.GOV)

Al-Shaieb, Z.; Shelton, J.W.

1978-03-01

Oil-productive, Oligocene Chadra sands in Gialo field, Libya, at depths of 600 to 750 m contain small dolomite rhombs. The rhombs are present as single crystals on detrital grains and as nonmosaic aggregates in pore space. The dolomite is calcium-rich and contains up to 10% iron but not measurable sodium or strontium. Total dissolved solids of produced interstitial water from the Chadra sand range from about 4,500 to 10,000 ppM. Introduction of fresh (meteoric) water into the Chadra sands, which were deposited in shallow-marine (shelf) environment, was responsible for formation of the dolomite rhombs. Iron in the dolomite rhombs wasmore » derived from alteration of galuconite.« less

Water requirements of the copper industry

USGS Publications Warehouse

Mussey, Orville Durey

1961-01-01

The copper industry in 1955 used about 330 million gallons of water per day in the mining and manufacturing of primary copper. This amount is about 0.3 percent of the total estimated withdrawals of industrial water in the United States in 1955. These facts were determined by a survey, in 1956, of the amount and chemical quality of the water used by the copper industry. A large part of this water was used in Arizona, Nevada, New Mexico, and Utah, where about five-sixths of the domestic copper is mined. Much of the remaining water use was near New York City where most of the electrolytic refineries are located, and the rest of the water was used in widely scattered places. A little more than 100,000 gallons of water per ton of copper was used in the production of copper from domestic ores. Of this amount about 70,000 gallons per ton was used in mining and concentrating the ore, and about 30,000 gallons per ton was used to reduce the concentrate to refined copper. In areas where water was scarce or expensive, the unit water use was a little more than half the average. About 60 mgd (million gallons per day) or 18 percent of the water was used consumptively, and nearly all of the consumptive use occurred in the water-short areas of the West. Of the water used in mining and manufacturing primary copper 75 percent was surface water and 25 percent was ground water, 89 percent of this water was self-supplied by the copper companies and 11 percent came from public supplies. Much of the water used in producing primary copper was of comparatively poor quality; about 46 percent was saline containing 1,000 ppm (parts per million) or more of dissolved solids and 54 percent was fresh. Water that is used for concentration of copper ores by flotation or even any water that comes in contact with the ore at any time before it reaches the flotation plant must be free of petroleum products because they interfere with the flotation process. The water used in mining and ore concentration was higher in dissolved solids and was harder than the water used in smelting and refining. Water used in mining and ore concentration had a median dissolved solids content of about 400 ppm and a median hardness (as CaCO3) of about 200 ppm. The median values for water used in smelting and refining were only half these amounts.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamzah, Zaini, E-mail: tengkuliana88@gmail.com; Rosli, Tengku Nurliana Tuan Mohd, E-mail: tengkuliana88@gmail.com; Saat, Ahmad, E-mail: tengkuliana88@gmail.com

An estuary is an area that has a free connection with the open sea and it is a dynamic semi-enclosed coastal bodies. Ex-mining, aquaculture and industrial areas in Selangor are the sources of pollutants discharged into the estuary water. Radionuclides are considered as pollutants to the estuary water. Gamma radiations emitted by natural radionuclides through their decaying process may give impact to human. The radiological effect of natural radionuclides which are {sup 226}Ra, {sup 228}Ra, {sup 40}K, {sup 238}U and {sup 232}Th, were explored by determining the respective activity concentrations in filtered water along the Langat estuary, Selangor. Meanwhile, in-more » situ water quality parameters such as temperature, dissolve oxygen (DO), salinity, total suspended solid (TSS), pH and turbidity were measured by using YSI portable multi probes meter. The activity concentration of {sup 226}Ra, {sup 228}Ra and {sup 40}K were determined by using gamma-ray spectrometry with high-purity germanium (HPGe) detector. The activity concentrations of {sup 226}Ra, {sup 228}Ra and {sup 40}K in samples are in the range of 0.17 - 0.67 Bq/L, 0.16 - 0.97 Bq/L and 1.22 - 5.57 Bq/L respectively. On the other hand, the concentrations of uranium-238 and thorium-232 were determined by using Energy Dispersive X-ray Fluorescence Spectrometry (EDXRF). The thorium concentrations are between 0.17 ppm to 0.28 ppm and uranium concentrations were 0.25 ppm to 0.31 ppm. The results show activity concentrations of radionuclides are slightly high near the river estuary. The Radium Equivalent, Absorbed Dose Rate, External Hazard Index, and Annual Effective Dose of {sup 226}Ra, {sup 228}Ra and {sup 40}K are also studied.« less

Removal of oil and oil sheen from produced water by pressure-assisted ozonation and sand filtration.

PubMed

Cha, Zhixiong; Lin, Cheng-Fang; Cheng, Chia-Jung; Andy Hong, P K

2010-01-01

Ever increasing energy demand worldwide necessitates energy supply, inevitably leading to an increasing volume of process waters containing hydrocarbon contaminants. Among them, dispersed and dissolved oils in produced water need to be removed adequately in order to reuse or avoid surface sheen from coastal discharge. We have recently developed a new ozonation technique coupled with sand filtration to quickly remove oil from process water and prevent oil sheen. The technique incorporates rapid, successive cycles of compression and decompression during ozonation. Gas bubbles expanding from small to large sizes occur that provide ample reactive zones at the gas-liquid interface, resulting in heightened chemical conversions-notably the conversion of hydrophobic hydrocarbon molecules into hydrophilic ones. This study examined the removal of hydrocarbons and sheen according to treatment parameters and configurations, as assessed by changes in turbidity, COD, BOD, and sheen presence following treatment. When a synthetic produced water containing 120ppm of oil (about 100ppm of dispersed and 20ppm of soluble oil at a total COD of 320mgL(-1)) was subjected to 10 pressure cycles (reaching 1.0MPa; 20s each) of ozonation and sand filtration at 6cmmin(-1) and then repeated by 20 cycles of ozonation and sand filtration, it resulted in removal of oil to 20ppm as water-soluble organic acids, decrease of turbidity from 200 to 2NTU, and complete sequestration of surface sheen. The new technique offers a treatment alternative for produced water and likely other tailings waters, promoting safe discharge to the environment and beneficial uses of the water. 2009 Elsevier Ltd. All rights reserved.

Larvicidal and repellent potential of Moringa oleifera against malarial vector, Anopheles stephensi Liston (Insecta: Diptera: Culicidae)

PubMed Central

Prabhu, K; Murugan, K; Nareshkumar, A; Ramasubramanian, N; Bragadeeswaran, S

2011-01-01

Objective To evaluate the larvicidal and pupicidal potential of the methanolic extracts from Moringa oleifera (M. oleifera) plant seeds against malarial vector Anopheles stephensi (A. stephensi) mosquitoes at different concentrations (20, 40, 60, 80 and 100 ppm). Methods M. oleifera was collected from the area of around Bharathiar University, Coimbatore. The dried plant materials were powdered by an electrical blender. From each sample, 100 g of the plant material were extracted with 300 mL of methanol for 8 h in a Soxhlet apparatus. The extracts were evaporated to dryness in rotary vacuum evaporator to yield 122 mg and 110 mg of dark greenish material (residue) from Arcang amara and Ocimum basilicum, respectively. One gram of the each plant residue was dissolved separately in 100 mL of acetone (stock solution) from which different concentrations, i.e., 20, 40, 60, 80 and 100 ppm were prepared. Results Larvicidal activity of M. oleifera exhibited in the first to fourth instar larvae of the A. stephensi, and the LC50 and LC90 values were 57.79 ppm and 125.93 ppm for the first instar, 63.90 ppm and 133.07 ppm for the second instar, 72.45 ppm and 139.82 ppm for the third instar, 78.93 ppm and 143.20 ppm for the fourth instar, respectively. During the pupal stage the methanolic extract of M. oleifera showed that the LC50 and LC90 values were 67.77 ppm and 141.00 ppm, respectively. Conclusions The present study indicates that the phytochemicals derived from M. oleifera seeds extracts are effective mosquito vector control agents and the plant extracts may be used for further integrated pest management programs. PMID:23569741

Larvicidal and repellent potential of Moringa oleifera against malarial vector, Anopheles stephensi Liston (Insecta: Diptera: Culicidae).

PubMed

Prabhu, K; Murugan, K; Nareshkumar, A; Ramasubramanian, N; Bragadeeswaran, S

2011-04-01

To evaluate the larvicidal and pupicidal potential of the methanolic extracts from Moringa oleifera (M. oleifera) plant seeds against malarial vector Anopheles stephensi (A. stephensi) mosquitoes at different concentrations (20, 40, 60, 80 and 100 ppm). M. oleifera was collected from the area of around Bharathiar University, Coimbatore. The dried plant materials were powdered by an electrical blender. From each sample, 100 g of the plant material were extracted with 300 mL of methanol for 8 h in a Soxhlet apparatus. The extracts were evaporated to dryness in rotary vacuum evaporator to yield 122 mg and 110 mg of dark greenish material (residue) from Arcang amara and Ocimum basilicum, respectively. One gram of the each plant residue was dissolved separately in 100 mL of acetone (stock solution) from which different concentrations, i.e., 20, 40, 60, 80 and 100 ppm were prepared. Larvicidal activity of M. oleifera exhibited in the first to fourth instar larvae of the A. stephensi, and the LC50 and LC90 values were 57.79 ppm and 125.93 ppm for the first instar, 63.90 ppm and 133.07 ppm for the second instar, 72.45 ppm and 139.82 ppm for the third instar, 78.93 ppm and 143.20 ppm for the fourth instar, respectively. During the pupal stage the methanolic extract of M. oleifera showed that the LC50 and LC90 values were 67.77 ppm and 141.00 ppm, respectively. The present study indicates that the phytochemicals derived from M. oleifera seeds extracts are effective mosquito vector control agents and the plant extracts may be used for further integrated pest management programs.

Novel ammonia sensor based on polyaniline/polylactic acid composite films

NASA Astrophysics Data System (ADS)

Sotirov, S.; Bodurov, I.; Marudova, M.

2017-01-01

We propose a new type of ammonia sensor based on composite film between polyaniline (emeraldine base) dissolved in dimethylformamide, and poly(DL-lactic) acid dissolved in chloroform. The two solutions were mixed in weight ratio of the components 1:1 and cast on Al2O3 substrate, on which silver electrodes were deposited previously. The active layer structure and morphology were examined by atomic force microscopy. The sensor resistance at constant humidity and different ammonia concentrations was measured. It was found that an increase in the ammonia concentration leads to resistance increase. This result is explained in the terms of ionic interactions between the polyaniline and the ammonia, which change the permittivity of the sensor active media. A response between 2% and 590% was shown depending on the ammonia concentration. The sensor is reversible and possesses response time of typically 100 s. Based on the changes of the sensor resistance, ammonia concentration from 10 ppm to 1000 ppm could be detected.

The effect of selenium on spoil suitability as root zone material at Navajo Mine, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lane, J.R.; Buchanan, B.A.; Ramsey, T.C.

1995-09-01

The root zone suitability limits for spoil Se at Navajo Mine in northwest New Mexico are currently 0.8 ppm total Se and 0.15 ppm hot-water soluble Se. These criteria were largely developed by the Office of Surface Mining using data from the Northern Great Plains. Applying these values, approximately 23% of the spoil volume and 47% of the spoil area sampled at Navajo Mine from 1985 to December 1993 were determined to be unsuitable as root zone material. Secondary Se accumulator plants (Atriplex canescens) growing in both undisturbed and reclaimed areas were randomly sampled for selenium from 1985 to Decembermore » 1993. In most cases the undisturbed soil and reclaimed spoil at these plant sampling sites were sampled for both total and hot-water soluble Se. Selenium values for Atriplex canescens samples collected on the undisturbed sites averaged 0.64 ppm and ranged from 0.20 ppm to 2.5 ppm. Selenium values for the plants growing on spoil ranged from 0.02 ppm to 7.75 ppm and averaged 1.07 ppm. Total and hot-water Se values for spoil averaged 0.66 ppm and 0.06 ppm respectively, and ranged from 0.0 to 14.2 for total Se and 0.0 ppm to 0.72 ppm for hot-water soluble Se. The plant Se values were poorly correlated to both total and hot-water soluble Se values for both soil and spoil. Therefore, predicting suitable guidelines using normal regression techniques was ineffective. Based on background Se levels in native soils, and levels found on reclaimed areas with Atriplex canescens, it is suggested that a total Se level of 2.0 ppm and a hot-water soluble Se level of 0.25 ppm should be used to represent the suitability limits for Se at Navajo Mine. If these Se values are used, it is estimated that less than 1% of the spoil volume would be unsuitable. This volume of spoil seems to be a more accurate estimate of the amount of spoil with unsuitable levels of Se than the estimated 23% using the current guidelines.« less

A low-cost, portable optical sensing system with wireless communication compatible of real-time and remote detection of dissolved ammonia

NASA Astrophysics Data System (ADS)

Deng, Shijie; Doherty, William; McAuliffe, Michael AP; Salaj-Kosla, Urszula; Lewis, Liam; Huyet, Guillaume

2016-06-01

A low-cost and portable optical chemical sensor based ammonia sensing system that is capable of detecting dissolved ammonia up to 5 ppm is presented. In the system, an optical chemical sensor is designed and fabricated for sensing dissolved ammonia concentrations. The sensor uses eosin as the fluorescence dye which is immobilized on the glass substrate by a gas-permeable protection layer. A compact module is developed to hold the optical components, and a battery powered micro-controller system is designed to read out and process the data measured. The system operates without the requirement of laboratory instruments that makes it cost effective and highly portable. Moreover, the calculated results in the system can be transmitted to a PC wirelessly, which allows the remote and real-time monitoring of dissolved ammonia.

The effect of CO2 availability on the growth, iron oxidation and CO2-fixation rates of pure cultures of Leptospirillum ferriphilum and Acidithiobacillus ferrooxidans.

PubMed

Bryan, C G; Davis-Belmar, C S; van Wyk, N; Fraser, M K; Dew, D; Rautenbach, G F; Harrison, S T L

2012-07-01

Understanding how bioleaching systems respond to the availability of CO(2) is essential to developing operating conditions that select for optimum microbial performance. Therefore, the effect of inlet gas and associated dissolved CO(2) concentration on the growth, iron oxidation and CO(2) -fixation rates of pure cultures of Acidithiobacillus ferrooxidans and Leptospirillum ferriphilum was investigated in a batch stirred tank system. The minimum inlet CO(2) concentrations required to promote the growth of At. ferrooxidans and L. ferriphilum were 25 and 70 ppm, respectively, and corresponded to dissolved CO(2) concentrations of 0.71 and 1.57 µM (at 30°C and 37°C, respectively). An actively growing culture of L. ferriphilum was able to maintain growth at inlet CO(2) concentrations less than 30 ppm (0.31-0.45 µM in solution). The highest total new cell production and maximum specific growth rates from the stationary phase inocula were observed with CO(2) inlet concentrations less than that of air. In contrast, the amount of CO(2) fixed per new cell produced increased with increasing inlet CO(2) concentrations above 100 ppm. Where inlet gas CO(2) concentrations were increased above that of air the additional CO(2) was consumed by the organisms but did not lead to increased cell production or significantly increase performance in terms of iron oxidation. It is proposed that At. ferrooxidans has two CO(2) uptake mechanisms, a high affinity system operating at low available CO(2) concentrations, which is subject to substrate inhibition and a low affinity system operating at higher available CO(2) concentrations. L. ferriphilum has a single uptake system characterised by a moderate CO(2) affinity. At. ferrooxidans performed better than L. ferriphilum at lower CO(2) availabilities, and was less affected by CO(2) starvation. Finally, the results demonstrate the limitations of using CO(2) uptake or ferrous iron oxidation data as indirect measures of cell growth and performance across varying physiological conditions. Copyright © 2012 Wiley Periodicals, Inc.

The effect of the ground water of three different locations on some morphometric measurements of broiler chicken in Jeddah-Saudi Arabia.

PubMed

El-Ghazaly, N; Bin Dohaish, E; Alsolamy, S

2008-02-15

In this study, the ground water from three different regions in Saudi Arabia; Hada El-Sham (G0), Om Al-Jood (G1) and El-Wazeria (G2) were tested to evaluate their suitability of using. For this purpose, the ground water were analysed and the physico-chemical characteristics were determined. The measured parameters were; pH, Total Dissolved Salts (TDS), Total Hardness (TH), Total Alkalinity (TA), cation (Na, K, Ca, Mg) and anion (NO3, SO4) concentrations. One hundred and currently from 21 day to six weeks broiler chicken were reared on the ground water of these locations and their morphometric measurements (body weight, feed and water consumption and feed assimilation) were recorded. From this study, it was noted that the ground water of G0 and G1 are very pure to be used in irrigation and drinking as they contain TDS less than 1100 ppm, whereas water of G2 cannot be used as the TDS value is 2650 ppm. However, the ground water of the three regions is not suitable for any kind of industry. Reared chicken in G0 were characterized by the highest growth rate despite of their lower rates of feed and water consumption. In G1, chicken had medium rates of growth and water consumption with higher rate of feed consumption. While chicken from G2 recorded the lowest growth rate and highest rate of water consumption due to the higher salt content of this water.

Oxygen requirement of separated hybrid catfish eggs

USDA-ARS?s Scientific Manuscript database

Channel catfish egg masses require hatchery water with over 7.8 ppm dissolved oxygen at 80° F (95% air saturation) to maintain maximum oxygen consumption as they near hatching. This concentration is called the critical oxygen requirement by scientists but for the purpose of this article we will call...

40 CFR 761.366 - Cleanup equipment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... scrubbers and absorbent pads that are not dissolved by the solvents or cleaners used, and that do not shred, crumble, or leave visible fragments on the surface. Scrubbers and absorbent pads used to wash contaminated surfaces must not be reused. Scrubbers and absorbent pads for rinsing must not contain ≥2 ppm PCBs...

40 CFR 180.940 - Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (Food...

Code of Federal Regulations, 2010 CFR

2010-07-01

... to exceed 200 ppm determined as total available chlorine Hypochlorous acid, lithium salt 13840-33-0... to exceed 200 ppm determined as total available chlorine and 30 ppm lithium Hypochlorous acid...

40 CFR 180.940 - Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (Food...

Code of Federal Regulations, 2011 CFR

2011-07-01

... to exceed 200 ppm determined as total available chlorine Hypochlorous acid, lithium salt 13840-33-0... to exceed 200 ppm determined as total available chlorine and 30 ppm lithium Hypochlorous acid...

40 CFR 180.940 - Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (Food...

Code of Federal Regulations, 2012 CFR

2012-07-01

... to exceed 200 ppm determined as total available chlorine Hypochlorous acid, lithium salt 13840-33-0... to exceed 200 ppm determined as total available chlorine and 30 ppm lithium Hypochlorous acid...

Dissolved-mineral inflow to Great Salt Lake and chemical characteristics of the salt lake brine: Summary for water years 1960, 1961, and 1964

USGS Publications Warehouse

Hahl, D.C.

1968-01-01

The investigation of dissolved-mineral inflow to Great Salt Lake during the water years 1960, 1961, and 1964 was conducted during conditions of streamflow that were representative of the lowest and the average recorded during the water years 1934-64. The study conducted during the 1960 and 1961 water years was limited to defining surface-water inflow at sites close to the lakeshore, as well as at sites used in the 1960-6 study. From these comparative data, estimates of inflow at the lakeshore were made for the 1960 and 1961 water years. During the 1964 water year, when inflow to the lake was probably representative of the 31-year period, about 800,000 acre-feet of water containing 2,200,000 tons of dissolved solids entered the lake.During the years of average streamflow, about 500,000 acre-feet of water which might be developed for culinary use, passes the lowest sampling sites on the Bear and Weber Rivers. Also, more than 90 percent of the flow near the mouths of the Bear, Weber, and Jordan Rivers would be suitable for irrigation.Sources of inflow could be selected to provide a water supply for a fresh-water lake east of Antelope Island. The supply would range from 300,000 acre-feet of water containing 800 ppm (parts per million) of dissolved solids during periods of low streamflow to 1 million acre-feet containing 500 ppm during periods of average streamflow.

Extracellular matrices for gastrointestinal surgery: Ex vivo testing and current applications

PubMed Central

Hoeppner, Jens; Marjanovic, Goran; Helwig, Peter; Hopt, Ulrich Theodor; Keck, Tobias

2010-01-01

AIM: To assess the effects of bile and pancreatic juice on structural and mechanical resistance of extracellular matrices (ECMs) in vitro. METHODS: Small-intestinal submucosa (SIS), porcine dermal matrix (PDM), porcine pericardial matrix (PPM) and bovine pericardial matrix (BPM) were incubated in human bile and pancreatic juice in vitro. ECMs were examined by macroscopic observation, scanning electron microscopy (SEM) and testing of mechanical resistance. RESULTS: PDM dissolved within 4 d after exposure to bile or pancreatic juice. SIS, PPM and PDM retained their integrity for > 60 d when incubated in either digestive juice. The effect of bile was found to be far more detrimental to mechanical stability than pancreatic juice in all tested materials. In SIS, the loss of mechanical stability after incubation in either of the digestive secretions was less distinct than in PPM and BPM [mFmax 4.01/14.27 N (SIS) vs 2.08/5.23 N (PPM) vs 1.48/7.89 N (BPM)]. In SIS, the extent of structural damage revealed by SEM was more evident in bile than in pancreatic juice. In PPM and BPM, structural damage was comparable in both media. CONCLUSION: PDM is less suitable for support of gastrointestinal healing. Besides SIS, PPM and BPM should also be evaluated experimentally for gastrointestinal indications. PMID:20731016

Dietary toxicity and tissue accumulation of methylmercury in American kestrels

USGS Publications Warehouse

Bennett, Richard S.; French, John B.; Rossmann, Ronald; Haebler, Romona J.

2009-01-01

American kestrels (Falco sparverius) were fed meat diets containing 0, 3, 6, or 12 ppm (dry weight) methylmercury chloride. Birds fed the 12-ppm diet started to show signs of neurotoxicity after 26 days and all died in 39?49 days. One male kestrel fed the 6-ppm diet died after 75 days of exposure and several others showed signs of neurotoxicity after 45 days. None of the birds fed the 3-ppm diet died or showed signs of toxicity. After 59 days of exposure, mercury concentrations in the liver, kidney, and blood of nonreproducing kestrels increased with increasing dietary concentration. Tissue concentrations of mercury also steadily increased over time in birds fed diets with 6 ppm mercury, which were necropsied at 8, 15, 29, or 59 days of exposure, reaching mean total mercury concentrations of 57, 46, and 45 ppm (wet weight) at 59 days in the liver, kidney, and whole blood, respectively. Two pairs of kestrels at each dietary concentration were allowed to breed. Eggs averaged 8.3 and 18.1 ppm (wet weight) total mercury from birds fed 3- and 6-ppm diets, respectively. Feathers grown during mercury exposure contained high concentrations of mercury: Birds fed 3- and 6-ppm diets contained 275 and 542 ppm total mercury, respectively.

Comparison of plasma generated nitrogen fertilizer to conventional fertilizers ammonium nitrate and sodium nitrate for pre-emergent and seedling growth

NASA Astrophysics Data System (ADS)

Andhavarapu, A.; King, W.; Lindsay, A.; Byrns, B.; Knappe, D.; Fonteno, W.; Shannon, S.

2014-10-01

Plasma source generated nitrogen fertilizer is compared to conventional nitrogen fertilizers in water for plant growth. Root, shoot sizes, and weights are used to examine differences between plant treatment groups. With a simple coaxial structure creating a large-volume atmospheric glow discharge, a 162 MHz generator drives the air plasma. The VHF plasma source emits a steady state glow; the high drive frequency is believed to inhibit the glow-to-arc transition for non-thermal discharge generation. To create the plasma activated water (PAW) solutions used for plant treatment, the discharge is held over distilled water until a 100 ppm nitrate aqueous concentration is achieved. The discharge is used to incorporate nitrogen species into aqueous solution, which is used to fertilize radishes, marigolds, and tomatoes. In a four week experiment, these plants are watered with four different solutions: tap water, dissolved ammonium nitrate DI water, dissolved sodium nitrate DI water, and PAW. Ammonium nitrate solution has the same amount of total nitrogen as PAW; sodium nitrate solution has the same amount of nitrate as PAW. T-tests are used to determine statistical significance in plant group growth differences. PAW fertilization chemical mechanisms are presented.

Dissolved inorganic carbon dynamics in the waters surrounding forested mangroves of the Ca Mau Province (Vietnam)

NASA Astrophysics Data System (ADS)

Koné, Y. J.-M.; Borges, A. V.

2008-04-01

Dissolved inorganic carbon (DIC) and ancillary data were obtained during the dry and rainy seasons in the waters surrounding two 10-year-old forested mangrove sites (Tam Giang and Kiên Vàng) located in the Ca Mau Province (South-West Vietnam). During both seasons, the spatial variations of partial pressure of CO 2 (pCO 2) were marked, with values ranging from 704 ppm to 11481 ppm during the dry season, and from 1209 ppm to 8136 ppm during the rainy season. During both seasons, DIC, pCO 2, total alkalinity (TAlk) and oxygen saturation levels (%O 2) were correlated with salinity in the mangrove creeks suggesting that a combination of lower water volume and longer residence time (leading to an increase in salinity due to evaporation) enhanced the enrichment in DIC, pCO 2 and TAlk, and an impoverishment in O 2. The low O 2 and high DIC and pCO 2 values suggest that heterotrophic processes in the water column and sediments controlled these variables. The latter processes were meaningful since the high DIC and TAlk values in the creek waters were related to some extent to the influx of pore waters, consistent with previous observations. This was confirmed by the stochiometric relationship between TAlk and DIC that shows that anaerobic processes control these variables, although this approach did not allow identifying unambiguously the dominant diagenetic carbon degradation pathway. During the rainy season, dilution led to significant decreases of salinity, TAlk and DIC in both mangrove creeks and adjacent main channels. In the Kiên Vàng mangrove creeks a distinct increase of pCO 2 and decrease of %O 2 were observed. The increase of TSM suggested enhanced inputs of organic matter probably from land surrounding the mangrove creeks, that could have led to higher benthic and water column heterotrophy. However, the flushing of water enriched in dissolved CO 2 originating from soil respiration and impoverished in O 2 could also have explained to some extent the patterns observed during the rainy season. Seasonal variations of pCO 2 were more pronounced in the Kiên Vàng mangrove creeks than in the Tam Giang mangrove creeks. The air-water CO 2 fluxes were 5 times higher during the rainy season than during the dry season in the Kiên Vàng mangrove creeks. In the Tam Giang mangrove creeks, the air-water CO 2 fluxes were similar during both seasons. The air-water CO 2 fluxes ranged from 27.1 mmol C m -2 d -1 to 141.5 mmol C m -2 d -1 during the dry season, and from 81.3 mmol m -2 d -1 to 154.7 mmol m -2 d -1 during the rainy season. These values are within the range of values previously reported in other mangrove creeks and confirm that the emission of CO 2 from waters surrounding mangrove forests are meaningful for the carbon budgets of mangrove forests.

Rapid decolorization of textile wastewater by green synthesized iron nanoparticles.

PubMed

Ozkan, Z Y; Cakirgoz, M; Kaymak, E S; Erdim, E

2018-01-01

The effectiveness of green tea (Camellia sinensis) and pomegranate (Punica granatum) extracts for the production of iron nanoparticles and their application for color removal from a textile industry wastewater was investigated. Polyphenols in extracts act as reducing agents for iron ions in aqueous solutions, forming iron nanoparticles. Pomegranate extract was found to have almost a 10-fold higher polyphenolic content than the same amount of green tea extract on a mass basis. However, the size of the synthesized nanoparticles did not show a correlation with the polyphenolic content. 100 ppm and 300 ppm of iron nanoparticles were evaluated in terms of color removal efficiency from a real textile wastewater sample. 300 ppm of pomegranate nanoscale zero-valent iron particles showed more than 95% color removal and almost 80% dissolved organic carbon removal. The degradation mechanisms are is considered to be adsorption and precipitation to a major extent, and mineralization to a minor extent.

Effects of fluoridated milk on root dentin remineralization.

PubMed

Arnold, Wolfgang H; Heidt, Bastian A; Kuntz, Sebastian; Naumova, Ella A

2014-01-01

The prevalence of root caries is increasing with greater life expectancy and number of retained teeth. Therefore, new preventive strategies should be developed to reduce the prevalence of root caries. The aim of this study was to investigate the effects of fluoridated milk on the remineralization of root dentin and to compare these effects to those of sodium fluoride (NaF) application without milk. Thirty extracted human molars were divided into 6 groups, and the root cementum was removed from each tooth. The dentin surface was demineralized and then incubated with one of the following six solutions: Sodium chloride NaCl, artificial saliva, milk, milk+2.5 ppm fluoride, milk+10 ppm fluoride and artificial saliva+10 ppm fluoride. Serial sections were cut through the lesions and investigated with polarized light microscopy and quantitative morphometry, scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The data were statistically evaluated using a one-way ANOVA for multiple comparisons. The depth of the lesion decreased with increasing fluoride concentration and was the smallest after incubation with artificial saliva+10 ppm fluoride. SEM analysis revealed a clearly demarcated superficial remineralized zone after incubation with milk+2.5 ppm fluoride, milk+10 ppm fluoride and artificial saliva+10 ppm fluoride. Ca content in this zone increased with increasing fluoride content and was highest after artificial saliva+10 ppm fluoride incubation. In the artificial saliva+10 ppm fluoride group, an additional crystalline layer was present on top of the lesion that contained elevated levels of F and Ca. Incubation of root dentin with fluoridated milk showed a clear effect on root dentin remineralization, and incubation with NaF dissolved in artificial saliva demonstrated a stronger effect.

The effects of saline water consumption on the ultrasonographic and histopathological appearance of the kidney and liver in Barki sheep.

PubMed

Ghanem, Mohamed; Zeineldin, Mohamed; Eissa, Attia; El Ebissy, Eman; Mohammed, Rasha; Abdelraof, Yassein

2018-05-18

The objective of this study was to evaluate the impact of varying degrees of water salinity on the ultrasonographical and histopathological appearance of the liver and kidneys in Barki sheep. Thirty Barki sheep (initial weight, 29.48 ± 0.81 kg) were allocated into three groups (n=10 per group) based on the type of drinking water for 9 months: the tap water (TW) group (350 ppm total dissolved solids [TDS]); the moderate saline water (MSW) group (4,557 ppm TDS); and the high saline water (HSW) group (8,934 ppm TDS). After 9 months, the body weight was significantly decreased in sheep subjected to MSW (P=0.0347) and HSW (P=0.0424). Alanine aminotransferase, aspartate aminotransferase, alkaline phosphatase, urea, and creatinine were significantly increased (P<0.05) in sheep subjected to MSW and HSW. Ultrasonographic examination of the right and left kidneys revealed an increased length of both kidneys with crystal formation, particularly in male sheep. Ultrasonographic examination of the liver showed hyperechogenic dots varying in size and number between males and females. Histopathological examination of kidney revealed significant changes in both MSW and HSW groups such as hyaline matrix formation, atrophied glomerular tufts, and intramedullary congestion. Histopathological examination of the liver revealed slight fatty liver changes, slight fibrosis around the bile duct, massive inflammatory cell infiltration and vacuolar changes of hepatocytes in both MSW and HSW groups. In conclusion, water salinity negatively affects the body weight, liver and kidney appearance of Barki sheep and thus sheep production.

Implications for carbon processing beneath the Greenland Ice Sheet from dissolved CO2 and CH4 concentrations of subglacial discharge

NASA Astrophysics Data System (ADS)

Pain, A.; Martin, J.; Martin, E. E.

2017-12-01

Subglacial carbon processes are of increasing interest as warming induces ice melting and increases fluxes of glacial meltwater into proglacial rivers and the coastal ocean. Meltwater may serve as an atmospheric source or sink of carbon dioxide (CO2) or methane (CH4), depending on the magnitudes of subglacial organic carbon (OC) remineralization, which produces CO2 and CH4, and mineral weathering reactions, which consume CO2 but not CH4. We report wide variability in dissolved CO2 and CH4 concentrations at the beginning of the melt season (May-June 2017) between three sites draining land-terminating glaciers of the Greenland Ice Sheet. Two sites, located along the Watson River in western Greenland, drain the Isunnguata and Russell Glaciers and contained 1060 and 400 ppm CO2, respectively. In-situ CO2 flux measurements indicated that the Isunnguata was a source of atmospheric CO2, while the Russell was a sink. Both sites had elevated CH4 concentrations, at 325 and 25 ppm CH4, respectively, suggesting active anaerobic OC remineralization beneath the ice sheet. Dissolved CO2 and CH4 reached atmospheric equilibrium within 2.6 and 8.6 km downstream of Isunnguata and Russell discharge sites, respectively. These changes reflect rapid gas exchange with the atmosphere and/or CO2 consumption via instream mineral weathering. The third site, draining the Kiagtut Sermiat in southern Greenland, had about half atmospheric CO2 concentrations (250 ppm), but approximately atmospheric CH4 concentrations (2.1 ppm). Downstream CO2 flux measurements indicated ingassing of CO2 over the entire 10-km length of the proglacial river. CO2 undersaturation may be due to more readily weathered lithologies underlying the Kiagtut Sermiat compared to Watson River sites, but low CH4 concentrations also suggest limited contributions of CO2 and CH4 from OC remineralization. These results suggest that carbon processing beneath the Greenland Ice Sheet may be more variable than previously recognized. Variations control whether discharge is a source or sink of atmospheric CO2 or CH4, but gas concentrations could be further modified by instream reactions. Increased meltwater fluxes should enhance the importance of greenhouse gas fluxes from subglacial discharge, and heighten the need to constrain variability in subglacial carbon processing.

Inorganic and organic carbon spatial variability in the Congo River during high waters (December 2013)

NASA Astrophysics Data System (ADS)

Borges, Alberto V.; Bouillon, Steven; Teodoru, Cristian; Leporcq, Bruno; Descy, Jean-Pïerre; Darchambeau, François

2014-05-01

Rivers are important components of the global carbon cycle, as they transport terrestrial organic matter from the land to the sea, and emit CO2 to the atmosphere. In particular, tropical systems that account for 60% of global freshwater discharge to the oceans. In contrast with south American rivers, very little information is available for African rivers on their carbon flows and stocks, in particular the Congo river, the second largest river in the World in terms of freshwater discharge (1457 km3 yr-1) and in terms of drainage basin (3.75 106 km2) located the second largest tropical forest in the World. Here, we report a data-set of continuous (every minute) records of the partial pressure of CO2 (pCO2) (total of 10,000 records), and discrete samples of particulate (POC) and dissolved (DOC) organic carbon (total of 75 samples) in the mainstem and major tributaries of the Congo river, along the 1700 km stretch from Kisangani to Kinshasa (total river length = 4374 km), during the high water period (December 2013). The pCO2 dynamic range was high ranging from minimum values of 2000 ppm in white waters tributaries (higher turbidity, conductivity and O2, lower DOC), up to maximal values of 18,000 ppm in blackwaters tributaries (lower turbidity, conductivity and O2, higher DOC). In the mainstem, very strong horizontal (cross-section) gradients were imposed by the presence of blackwaters close to the riverbanks and the presence of whitewaters in the middle of the river. In the mainstem, a distinct horizontal (longitudinal) pattern was observed with pCO2 increasing, and conductivity and turbidity decreasing downstream.

Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination

PubMed Central

Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J.; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

2016-01-01

There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes. PMID:27545955

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaplan, Ruth; Mamrosh, Darryl; Salih, Hafiz H.

Brine extraction is a promising strategy for the management of increased reservoir pressure, resulting from carbon dioxide (CO 2) injection in deep saline reservoirs. The extracted brines usually have high concentrations of total dissolved solids (TDS) and various contaminants, and require proper disposal or treatment. In this article, first by conducting a critical review, we evaluate the applicability, limits, and advantages or challenges of various commercially available and emerging desalination technologies that can potentially be employed to treat the highly saline brine (with TDS values >70.000 ppm) and those that are applicable to a ~200,000 ppm TDS brine extracted frommore » the Mt. Simon Sandstone, a potential CO 2 storage site in Illinois, USA. Based on the side-by-side comparison of technologies, evaporators are selected as the most suitable existing technology for treating Mt. Simon brine. Process simulations are then conducted for a conceptual design for desalination of 454 m 3/h (2000 gpm) pretreated brine for near-zero liquid discharge by multi-effect evaporators. In conclusion, the thermal energy demand is estimated at 246kWh perm 3 of recoveredwater, ofwhich 212kWh/m 3 is required for multiple-effect evaporation and the remainder for salt drying. The process also requires additional electrical power of ~2 kWh/m 3.« less

Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination

NASA Astrophysics Data System (ADS)

Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J.; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

2016-08-01

There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes.

Hot-spring sinter deposits in the Alvord-Pueblo Valley, Harney County, Oregon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cummings, M.L.; St. John, A.M.

1993-04-01

Silica sinter deposits occur at Borax Lake, Alvord Hot Springs, and Mickey Springs in the Alvord-Pueblo Valley. Although the sinter deposits occur in areas of active hot springs, sinter is not being deposited. Hot springs are localized along faults that have been active since the Pleistocene. The sinter deposits formed after the drying of glacial Lake Alvord, but before and during extensive wind deflation of glacial-lacustrine sediments. At Mickey Springs, sinter rests directly on unaltered, unconsolidated lithic-rich sand. At Borax Lake, sinter overlies unaltered diatomite, but some armoring, presumably by silica, of the 30 m vent has developed. Field relationsmore » suggest rapid dumping of silica from solution without alteration of the country rock at the vent. Discharge of thermal fluids and cold groundwater along the same structure may have produced colloidal silica carried in a solution stripped of dissolved silica. Sinter is composed of opal-a, traces of detrital feldspar and quartz, and evaporation-related boracite. The concentration of Sb is similar among the three sinter deposits (20 to 70 ppm); however, As, Cs, and Br are highest at Borax Lake (5 to 560 ppm; 26 to 118 ppm; 5 to 1,040 ppm) while Hg is highest at Mickey Springs (1.0 to 5.2 ppm).« less

Chromatographic methods for determination of macrolide antibiotic residues in tissues and milk of food-producing animals.

PubMed

Moats, W A

1985-01-01

Tylosin, an antibiotic developed specifically for agricultural use, and erythromycin are the main macrolide antibiotics used in animal production. Two-dimensional thin layer chromatography has been used for detection of tylosin in poultry meat, eggs, and milk and for erythromycin in poultry meat. Detection limits reported are, for tylosin, 0.1 ppm in poultry meat, 0.05 ppm in egg, and 0.01 ppm in milk, and for erythromycin, 0.25 ppm in poultry meat. Liquid chromatography (LC) has also been used for determination of tylosin in milk, blood, and tissues of animals. Samples (milk, blood serum, or tissue homogenates in water or pH 2.2 buffer) were deproteinized with acetonitrile, tylosin was partitioned into methylene chloride, and the extracts were concentrated and dissolved in acetonitrile. Chromatography was done on a reverse phase end-capped C18 column using 0.002-0.005 M ammonium dihydrogen phosphate-acetonitrile-methanol (10 + 60 + 30-5 + 80 + 15). Solvent composition was varied with the type of sample analyzed. The method will detect 0.1 ppm tylosin in tissues and less in milk and blood serum. The LC method was more sensitive than microbiological assays for detection of tylosin in tissues of treated swine; recoveries of tylosin by the LC method were frequently several-fold higher.

Measurement of Eu and Yb in aqueous solutions by underwater laser induced breakdown spectroscopy

DOE PAGES

Bhatt, Chet R.; Jain, Jinesh C.; Goueguel, Christian L.; ...

2017-09-13

In this paper, we report the use of laser induced breakdown spectroscopy (LIBS) to detect dissolved Eu and Yb in bulk aqueous solutions. Ten strong emission lines of Eu and one strong emission line of Yb were identified in the underwater LIBS spectra obtained by using Czerny–Turner spectrometer within the wavelength range of 375–515 nm. Temporal evolution of plasma and the effect of laser pulse energy on the spectral emission were studied. Finally, calibration curves using the concentration range from 500 to 10,000 ppm were developed and limits of detection for Eu and Yb were estimated to be 209 andmore » 156 ppm, respectively.« less

Determination of trace amounts of tin in geological materials by atomic absorption spectrometry

USGS Publications Warehouse

Welsch, E.P.; Chao, T.T.

1976-01-01

An atomic absorption method is described for the determination of traces of tin in rocks, soils, and stream sediments. A dried mixture of the sample and ammonium iodide is heated to volatilize tin tetraiodide -which is then dissolved in 5 % hydrochloric acid, extracted into TOPO-MIBK, and aspirated into a nitrous oxide-acetylene flame. The limit of determination is 2 p.p.m. tin and the relative standard deviation ranges from 2 to 14 %. Up to 20 % iron and 1000 p.p.m. Cu, Pb, Zn, Mn, Hg, Mo, V, or W in the sample do not interfere. As many as 50 samples can be easily analyzed per man-day. ?? 1976.

Measurement of Eu and Yb in aqueous solutions by underwater laser induced breakdown spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhatt, Chet R.; Jain, Jinesh C.; Goueguel, Christian L.

In this paper, we report the use of laser induced breakdown spectroscopy (LIBS) to detect dissolved Eu and Yb in bulk aqueous solutions. Ten strong emission lines of Eu and one strong emission line of Yb were identified in the underwater LIBS spectra obtained by using Czerny–Turner spectrometer within the wavelength range of 375–515 nm. Temporal evolution of plasma and the effect of laser pulse energy on the spectral emission were studied. Finally, calibration curves using the concentration range from 500 to 10,000 ppm were developed and limits of detection for Eu and Yb were estimated to be 209 andmore » 156 ppm, respectively.« less

Rumen modulatory effect of thyme, clove and peppermint oils in vitro using buffalo rumen liquor.

PubMed

Roy, Debashis; Tomar, S K; Kumar, Vinod

2015-02-01

The present study was conducted to examine the rumen modulatory effect of thyme, clove and peppermint oils on rumen fermentation pattern in vitro using roughage based diet. Thyme, clove and peppermint oils were tested at concentration of 0, 30, 300 and 600 mg/l (ppm) of total culture fluid using in vitro gas production technique in wheat straw based diet (concentrate: Wheat straw 50:50). Different in vitro parameters e.g., total gas production, methane production, nutrient degradability, volatile fatty acid (VFA) production and ammonia nitrogen concentration were studied using buffalo rumen liquor. Thyme oil at higher dose level (600 ppm) reduced (p<0.05) total gas production, feed degradability and ammonia nitrogen (NH3-N) concentration whereas total VFA concentration was significantly lower (p>0.05) in 300 and 600 ppm dose levels. 600 ppm dose level of clove oil reduced (p<0.05) total gas production, feed degradability, total VFA and acetate to propionate ratio. Methane production was significantly reduced (p<0.05) in 300 and 600 ppm dose levels of clove and peppermint oil. Right combination of these essential oils may prove to enhance performance of animals by reducing methane production and inhibiting protein degradation in rumen.

The Influenced of Lactobacillus plantarum Starter Addition and The Length Time of Fermentation Process on The Activity of Seaweed Antioxidant Ulva lactuca from Krakal Beach, Yogyakarta

NASA Astrophysics Data System (ADS)

Ambarsari, N. D.; Rushanti, I. R. P. A.; Setyaji, A.; Ningsih, T. R.; Nurhana, N.; Subekhi, I.; Dewi, E. N.

2018-02-01

Seaweed contains phenol compound functioning as antioxidant. Lactobacillus plantarum starter addition in a fermentation process was expected will increase the activity of antioxidant. The purpose of this research was to determine the influence of L. plantarum addition and the length of fermentation on the activity of antioxidant in U. lactuca. The experiment was conducted with factorial design. The first treatment consisted 2 different factors namely without L. plantarum addition and L. plantarum addition. While the second treatment were the different length fermentation time: 0, 12, 24, and 36 hours. Each treatment were done in thriplicate. The data was analyzed using ANOVA and BNJ test was applied if there any differences betweenthe treatments. The results showed that the fresh U. lactuca with L. plantarum addition for 36 hours fermentation had TPC BAL 9,83 CFU/ml, pH 4,26, phenol 231 ppm and antioxidant activity IC501375,12 ppm. Dried U. lactuca with L. plantarum addition that was fermentized for 36 hours had TPC BAL 9,10 CFU/ml, pH 4,75, phenol 166,24 ppm and antioxidant activity IC504070,32 ppm. The fresh U. lactuca with L. plantarum addition for 36 hours fermentation was the best treatment since the antioxidant activity is IC501375,12 ppm. Although the antioxidant activity was categorized as weak but it was still showed an increase compared to the result of antioxidant activity with maceration method using n-hexana dissolver which was 11213,76 ppm, ethyl acetate 9770,285 ppm, and ethanol extact 4921,79 ppm.

Water resources inventory of Connecticut Part 3: lower Thames and southeastern coastal river basins

USGS Publications Warehouse

Thomas, Chester E.; Cervione, Michael A.; Grossman, I.G.

1968-01-01

The lower Thames and southeastern coastal river basins have a relatively abundant supply of water of generally good quality which is derived from streams entering the area and precipitation that has fallen on the area. Annual precipitation has ranged from about 32 inches to 65 inches and has averaged about 48 inches over a 30-year period. Approximately 22 inches of water are returned to the atmosphere each year by evaporation and transpiration; the remainder of the annual precipitation either flows overland to streams or percolates downward to the water table and ultimately flows out of the report area through estuaries and coastal streams or as underflow through the deposits beneath. During the autumn and winter months precipitation normally is sufficient to cause a substantial increase in the amount of water stored underground and in surface reservoirs within the report area, whereas in the summer most of the precipitation is lost through evaporation and transpiration, resulting in sharply reduced stream-flow and lowered ground-water levels. The mean monthly storage of water on an average is about 3.8 inches higher in November than it is in June. The amount of water that flows through and out of the report area represents the total amount of water potentially available for use by man. For the 30-year period 1931 through 1960, the annual runoff from the report area has averaged nearly 26 inches (200 billion gallons), from the entire Thames River basin above Norwich about 24 inches (530 billion gallons), and from the Pawcatuck River basin about 26 inches (130 billion gallons). A total average annual runoff of 860 billion gallons is therefore available. Although runoff indicates the total amount of water potentially available, it is usually not economically feasible for man to use all of it. On the other hand, with increased development, it is possible that some water will be reused several times. The water available may be tapped as it flows through the area or is temporarily stored in streams, lakes, and aquifers. The amounts that can be developed vary from place to place and time to time, depending on the amount of precipitation, on the size of drainage area, on the thickness, permeability, and areal extent of aquifers, and on the variations in chemical and physical quality of the water. Differences in streamflow from point to point are due primarily to differences in the proportion of stratified drift in the drainage basin above each point, which affect the timing of streamflow, and to differences in precipitation, which affect the amount of streamflow. Ground water can be obtained from wells almost anywhere in the area, but the amount obtainable at any particular point depends upon the type and water-bearing properties of the aquifers. For practical purposes, the earth materials in the report area comprise three aquifers--stratified drift, bedrock, and till. Stratified drift is the only aquifer generally capable of yielding more than 100 gpm (gallons per minute) to individual wells. It covers about 20 percent of the area and occurs chiefly in lowlands where it overlies till and bedrock. The coefficient of permeability of the coarse-grained unit of stratified drift averages about 1,500 gbd (gallons per day) per sq ft. Drilled, screened wells tapping this unit are known to yield from 4 to 88o gpm and average 146 gpm. Dug wells in coarse-grained stratified drift supply about 2 gpm per foot of drawdown over a period of a few hours. Fine-grained stratified drift has an average coefficient of permeability of about 300 gpd per sq ft and can usually yield supplies sufficient for household use to dug wells. Bedrock and till are widespread in extent but generally provide only small water supplies. Bedrock is tapped chiefly by drilled wells, about 90 percent of which will supply at least 3 gpm. Very few, however, will supply more than 50 gpm. Till is tapped in a few places by dug wells which can yield small supplies of only a few hundred gpd throughout all or most of the year. The coefficient of permeability of till ranges from about 0.2 gpd per sq ft to 120 gpd per sq ft. The amount of ground water potentially available in the report area depends upon the amount of ground-water outflow, the amount of ground water in storage, and the quantity of water available by induced infiltration from streams and lakes. From data on permeability, saturated thickness, recharge, yield from aquifer storage, well performance, and streamflow, preliminary estimates of ground-water availability can be made for any point in the report area. Long-term yields estimated for 18 areas of stratified drift especially favorable for development of large ground-water supplies ranged from 1.3 to 66 mgd. Detailed site studies to determine optimum yields, drawdowns, and spacing of individual wells are needed before major ground-water development is undertaken in these or other areas. The chemical quality of water in the report area is generally good to excellent. Samples of naturally occurring surface water collected at 24 sites contained less than 151 ppm (parts per million) of dissolved solids and less than 63 ppm of hardness. Water from wells is more highly mineralized than naturally occurring water from streams. Even so only 12 percent of the wells sampled yielded water with more than 200 ppm of dissolved solids and only 8 percent yielded water with more than 120 ppm of hardness. Even in major streams, which are used to transport industrial waste, hardness rarely exceeds 60 ppm and the dissolved mineral content is generally less than 200 ppm. At a few places in the town of Montville however, waters may contain dissolved mineral concentrations of 2,000 to 4,000 ppm. Iron and manganese in both ground water and surface water are the only constituents whose concentrations commonly exceed recommended limits for domestic and industrial use. Most wells in the report area yield clear water with little or no iron or manganese, but distributed among them are wells yielding ground water that contains enough of these dissolved constituents to be troublesome for most uses. Iron concentrations in naturally occurring stream water exceed 0.3 ppm under low-flow conditions at 33 percent of the sites sampled. Large concentrations of iron in stream water result from discharge of iron-bearing water from aquifers or from swamps where it is released largely from decaying vegetation. Ground water more than 30 feet below the land surface has a relatively constant temperature, usually between 48°F and 52°F. Water temperature in very shallow wells may fluctuate from about 38°F in February or March to about 55°F in late summer. Water temperature in the larger streams fluctuates much more widely, ranging from 32°F at least for brief periods in winter, to about 85°F occasionally during summer. The quality of suspended sediment transported by streams in the area is negligible. Turbidity in streams is generally not a problem although amounts large enough to be troublesome may occur locally at times. The total amount of water used in the report area for all purposes during 1964 was about 118,260 million gallons, of which 105,600 million gallons was estuarine water used for cooling by industry. The average per capita water use, excluding estuarine, temporary summer residence, and institutional water was equivalent to 186 gpd. Public water systems supplied the domestic needs of nearly tw0-thirds the population of the report area. All of the 19 systems, which were sampled, provided water of better quality than the U.S. Public Health Service suggests for drinking water standards.

Uranium-series dating of pedogenic silica and carbonate, Crater Flat, Nevada

NASA Astrophysics Data System (ADS)

Ludwig, K. R.; Paces, J. B.

2002-02-01

A 230Th-234U-238U dating study on pedogenic silica-carbonate clast rinds and matrix laminae from alluvium in Crater Flat, Nevada was conducted using small-sample thermal-ionization mass spectrometry (TIMS) analyses on a large suite of samples. Though the 232Th content of these soils is not particularly low (mostly 0.1-9 ppm), the high U content of the silica component (mostly 4-26 ppm) makes them particularly suitable for 230Th/U dating on single, 10 to 200 mg totally-digested samples using TIMS. We observed that (1) both micro- (within-rind) and macro-stratigraphic (mappable deposit) order of the 230Th/U ages were preserved in all cases; (2) back-calculated initial 234U/238U fall in a restricted range (typically 1.67±0.19), so that 234U/238U ages with errors of about 100 kyr (2σ) could be reliably determined for the oldest, 400 to 1000 ka rinds; and (3) though 13 of the samples were >350 ka, only three showed evidence for an open-system history, even though the sensitivity of such old samples to isotopic disruption is very high. An attempt to use leach-residue techniques to separate pedogenic from detrital U and Th failed, yielding corrupt 230Th/U ages. We conclude that 230Th/U ages determined from totally dissolved, multiple sub-mm size subsamples provide more reliable estimates of soil chronology than methods employing larger samples, chemical enhancement of 238U/232Th, or isochrons.

Removal of naphthenic acids using adsorption process and the effect of the addition of salt.

PubMed

Azad, Fakhry Seyedeyn; Abedi, Jalal; Iranmanesh, Sobhan

2013-01-01

In this study, various types of adsorbents were examined for the removal of Naphthenic acids (NAs) in the preliminary stage of this study. Among them, activated carbon and nickel (Ni) based alumina (Ni-Al2O3) possess relatively high adsorption capacity of NAs. The removal of NAs was evaluated comparing the total organic carbon (TOC) of the solution before and after the adsorption process. The effect of Ni loading was investigated using Ni-Al2O4 with various nickel loadings. The highest adsorption capacity (20 mg of TOC/1 mg of adsorbent) was belong to Ni-Al2O4 with 10.7% Ni loading. By the addition of salt (1500 ppm NaCl) to NAs solutions having concentrations from of 15 to 38 ppm, it was observed that the adsorption decreased dramatically (up to 80%) depending on the concentration of TOC. The kinetics of the adsorption of TOC on Ni-based alumina was also investigated. The decrease of TOC was more that 40% in the first half hour, indicating that adsorption was very rapid in the beginning. The adsorption increased slightly for up to 5 h and then leveled off when the TOC reached to 50% of initial TOC concentration. However, when sodium chloride (NaCl) was added to the solution, the adsorption decreased to almost 9% within the first half hour, reaching to almost 5% after 3 h. These phenomena suggest that the effectiveness of adsorbents may be improved by decreasing the total dissolved salts in tailings pond wastewater.

Development and performance evaluation of air fine bubbles on water quality of thai catfish rearing

NASA Astrophysics Data System (ADS)

Subhan, Ujang; Muthukannan, Vanitha; Azhary, Sundoro Yoga; Mulhadi, Muhammad Fakhri; Rochima, Emma; Panatarani, Camellia; Joni, I. Made

2018-02-01

The efficiency and productivity of aquaculture strongly depends on the development of advanced technology for water quality management system. The most important factor for the success of intensive aquaculture system is controlling the water quality of fish rearing media. This paper reports the design of fine bubbles (FBs) generator and performance evaluation of the system to improve water quality in thai catfish media (10 g/ind) with density (16.66 ind./L). The FBs generator was designed to control the size distribution of bubble by controlling its air flow rate entry to the mixing chamber of the generator. The performance of the system was evaluated based on the produced debit, dissolved oxygen rate and ammonia content in the catfish medium. The size distribution was observed by using a high speed camera image followed by processing using ImageJ. freeware application. The results show that air flow rate 0.05 L/min and 0.1 L/min received average bubble size of 29 µm and 31 µm respectively. The generator produced bubbles with capacity of 6 L/min and dissolved oxygen rate 0.2 ppm/min/L. The obtained DO growth was 0.455 ppm/second/L while the average decay rate was 0.20 ppm/second/L. (0.011/0.005 fold). In contrast, the recieved DO growth rate is faster compared to the DO consumption rate of the Thai catfish. This results indicated that the potential application of FBs enhanced the density of thai catfish seed rearing. In addition, ammonia can be reduced at 0.0358 ppm/hour/L and it is also observed that the inhibition of bacterial growth of air FBs is postive to Aeromonas hydrophila bacteria compared to the negative control. It is concluded that as-developed FBs system can be potentially applied for intensive thai catfish culture and expected to improve the feeding efficiency rate.

Water Quality in Courtland Creek, East Oakland, California

NASA Astrophysics Data System (ADS)

Bracho, H.; Ahumada, A.; Hernandez, G.; Quintero, D.; Ramirez, J.; Ramirez, L.; Pham, T.; Holt, J.; Johnson, A.; Rubio, E.; Ponce, X.; Medina, S.; Limon, S.

2013-12-01

Courtland Creek is a tributary of the larger East Creek system that runs southeast from the Oakland Hills down to the San Leandro Bay in Oakland, California. In an effort to assess the overall health of Courtland Creek our team conducted a water quality research study. Stream water samples were collected from 4 sites between MacArthur Avenue (describe geographically as not all readers are familiar with Oakland geography) and Thompson Avenue (describe geographically as not all readers are familiar with Oakland geography) at accessible sections of this largely culverted stream. Dissolved oxygen, ammonia, nitrite, nitrate, phosphate, and chlorine concentrations in were measured using wet chemistry procedures. Analysis of collected samples indicates that dissolved oxygen levels in the stream are sufficient for invertebrates, ranging from 5 and 9 parts per million (ppm). Nitrate levels were significantly high, with concentrations ranging from 15 and 40 ppm. Other chemical species associated with waste products--ammonia, nitrite, and phosphate--also were present, but at low concentrations. Small amounts of chlorine also were found in waters of the creek system. The presence of high concentrations of nitrate, together with chlorine, suggests that untreated sewage may be leaking into Courtland Creek at an unidentified location.

Measurement of H2S in Crude Oil and Crude Oil Headspace Using Multidimensional Gas Chromatography, Deans Switching and Sulfur-selective Detection

PubMed Central

Heshka, Nicole E.; Hager, Darcy B.

2015-01-01

A method for the analysis of dissolved hydrogen sulfide in crude oil samples is demonstrated using gas chromatography. In order to effectively eliminate interferences, a two dimensional column configuration is used, with a Deans switch employed to transfer hydrogen sulfide from the first to the second column (heart-cutting). Liquid crude samples are first separated on a dimethylpolysiloxane column, and light gases are heart-cut and further separated on a bonded porous layer open tubular (PLOT) column that is able to separate hydrogen sulfide from other light sulfur species. Hydrogen sulfide is then detected with a sulfur chemiluminescence detector, adding an additional layer of selectivity. Following separation and detection of hydrogen sulfide, the system is backflushed to remove the high-boiling hydrocarbons present in the crude samples and to preserve chromatographic integrity. Dissolved hydrogen sulfide has been quantified in liquid samples from 1.1 to 500 ppm, demonstrating wide applicability to a range of samples. The method has also been successfully applied for the analysis of gas samples from crude oil headspace and process gas bags, with measurement from 0.7 to 9,700 ppm hydrogen sulfide. PMID:26709594

Mercury speciation, fluxes, and fate in the volcanically acidified fluids of Copahue volcano, Argentina

NASA Astrophysics Data System (ADS)

Kading, T.; Varekamp, J. C.; Andersson, M.; Balcom, P.; Mason, R. P.

2010-12-01

The behavior of mercury in volcanic acid springs and acidified rivers is poorly known, despite the potential impact this vector of contamination has on local surface and ground water quality. Mercury was measured in a volcanically acidified river system (pH<1 - 3), the Rio Agrio in the Neuquen province of Argentina, which discharges into a large glacial lake (Lake Caviahue, pH 2.2-3.0). The Hg concentration ranged from 2 - 600 pM throughout the fluvial system. Mercury in the hot, hyperacidic source fluids was dominated by dissolved ionic species, with only 2% of total mercury as dissolved elemental mercury, and 11% being particulate bound. The Hg flux from the volcano, determined from river water flux measurements and Hg concentrations, was modest and varied between the 3/2008 and 3/2009 sampling campaigns resp. from 0.7 to 1.1 moles/year. The Hg:S ratio of the acid fluids was ~10-8, several orders of magnitude lower than that typically found in volcanic plumes and fumaroles. The small Hg flux and low Hg:S values suggest that the system is either inherently Hg-poor or has lost Hg through vapor loss deeper in the hydrothermal system. Support for the latter comes from high Hg concentrations in geothermal vents and mudpots on the flank of the mountain (24 - 55 ppm Hg). Mercury concentrations decreased conservatively downstream in the river as based on Hg/Cl and Hg/SO4. Non-conservative depletion occurs in the less acidic Lake Caviahue, suggesting that mercury is removed from the water column by sorption to organic matter or other phases. Mercury analyses of a short lake sediment core confirm this (Hg = 0.01 to 0.70 ppm). No evidence was found for preferential uptake of mercury by jarosite, schwertmannite, or goethite, although the latter two phases precipitate in the most distal and Hg-depleted section of the fluvial system.

Tumors and proliferative lesions in adult offspring after maternal exposure to methylarsonous acid during gestation in CD1 mice.

PubMed

Tokar, Erik J; Diwan, Bhalchandra A; Thomas, David J; Waalkes, Michael P

2012-06-01

Developmental exposure to inorganic arsenic is carcinogenic in humans and mice, and adult offspring of mice exposed to inorganic arsenic can develop tumors of the lung, liver, adrenal, uterus, and ovary. It has been suggested that methylarsonous acid (MMA3+), a product of the biological methylation of inorganic arsenic, could be a key carcinogenic species. Thus, pregnant CD1 mice were provided drinking water containing MMA3+ at 0 (control), 12.5, or 25 parts per million (ppm) from gestational days 8 to 18. Tumors were assessed in groups of male or female (initial n = 25) offspring up to 2 years of age. In utero treatment had no effect on survival or body weights. Female offspring exhibited increases in total epithelial uterine tumors (control 0%; 12.5 ppm 26%; 25 ppm 30%), oviduct hyperplasia (control 4%; 12.5 ppm 35%; 25 ppm 43%), adrenal cortical adenoma at 25 ppm (control 0%; 12.5 ppm 9%; 25 ppm 26%), and total epithelial ovarian tumors (control 0%; 12.5 ppm 39%; 25 ppm 26%). Male offspring showed dose-related increases in hepatocellular carcinoma (control 0%; 12.5 ppm 12%; 25 ppm 22%), adrenal adenoma (control 0%; 12.5 ppm 28%; 25 ppm 17%), and lung adenocarcinoma (control 17%; 12.5 ppm 44%). Male offspring had unusual testicular lesions, including two rete testis carcinomas, two adenomas, and three interstitial cell tumors. Overall, maternal consumption of MMA3+ during pregnancy in CD1 mice produced some similar proliferative lesions as gestationally applied inorganic arsenic in the offspring during adulthood.

Tumors and Proliferative Lesions in Adult Offspring After Maternal Exposure to Methylarsonous Acid During Gestation in CD1 Mice

PubMed Central

Tokar, Erik J.; Diwan, Bhalchandra A.; Thomas, David J.; Waalkes, Michael P.

2012-01-01

Developmental exposure to inorganic arsenic is carcinogenic in humans and mice, and adult offspring of mice exposed to inorganic arsenic can develop tumors of the lung, liver, adrenal, uterus, and ovary. It has been suggested that methylarsonous acid (MMA3+), a product of the biological methylation of inorganic arsenic, could be a key carcinogenic species. Thus, pregnant CD1 mice were provided drinking water containing MMA3+ at 0 (control), 12.5 or 25 parts per million (ppm) from gestational day 8 to 18. Tumors were assessed in groups of male or female (initial n = 25) offspring up to two years of age. In utero treatment had no effect on survival or body weights. Female offspring exhibited increases in total epithelial uterine tumors (control 0%; 12.5 ppm 26%; 25 ppm 30%), oviduct hyperplasia (control 4%; 12.5 ppm 35%; 25 ppm 43%), adrenal cortical adenoma at 25 ppm (control 0%; 12.5 ppm 9%; 25 ppm 26%), and total epithelial ovarian tumors (control 0%; 12.5 ppm 39%; 25 ppm 26%). Male offspring showed dose-related increases in hepatocellular carcinoma (control 0%; 12.5 ppm 12%; 25 ppm 22%), adrenal adenoma (control 0%; 12.5 ppm 28%; 25 ppm 17%), and lung adenocarcinoma (control 17%; 12.5 ppm 44%). Male offspring had unusual testicular lesions, including two rete testis carcinomas and two adenomas, and three interstitial cell tumors. Overall, maternal consumption of MMA3+ during pregnancy in CD1 mice produced some similar proliferative lesions as gestationally applied inorganic arsenic in the offspring during adulthood. PMID:22398986

Inactivation of Ichthyophonus spores using sodium hypochlorite and polyvinyl pyrrolidone iodine

USGS Publications Warehouse

Hershberger, P.K.; Pacheco, C.A.; Gregg, J.L.

2008-01-01

Chlorine and iodine solutions were effective at inactivating Ichthyophonus spores in vitro. Inactivation in sea water increased directly with halogen concentration and exposure duration, with significant differences (P < 0.05) from controls occurring at all chlorine concentrations and exposure durations tested (1.5-13.3 ppm for 1-60 min) and at most iodine concentrations and exposure durations tested (1.2 ppm for 60 min and 5.9-10.7 ppm for 1-60 min). However, 10-fold reductions in spore viability occurred only after exposure to halogen solutions at higher concentrations and/or longer durations (13 ppm total chlorine for 1-60 min, 5.9 ppm total iodine for 60 min, and 10.7 ppm total iodine for 1-60 min). Inactivation efficacy was greater when halogen solutions were prepared in fresh water, presumably because of combined effects of halogen-induced inactivation and general spore instability in fresh water. The results have practical implications for disinfection and biocontainment in research laboratories and other facilities that handle live Ichthyophonus cultures and/or infected fish.

[Flow injection-spectrophotometric determination of total dissolved nitrogen in seawater based on quantificational solenoid valves].

PubMed

Han, Bin; Cao, Lei; Zheng, Li; Zang, Jia-ye; Wang, Xiao-ru

2012-01-01

Using three pipe clamp solenoid valves to replace the traditional six-port valve for sample quota, a set of multi-channel flow injection analyzer was designed in the present paper. The authors optimized optimum instrumental testing condition, and realized determination and analysis of total dissolved nitrogen in seawaters. The construction of apparatus is simple and it has the potential to be used for analysis of total dissolved nitrogen. The sample throughput of total dissolved nitrogen was 27 samples per hour. The linear range of total dissolved nitrogen was 50.0-1 000.0 microgN x L(-3) (r > or = 0.999). The detection limit was 7.6 microgN x L(-3). The recovery of total dissolved nitrogen was 87.3%-107.2%. The relative standard deviation for total dissolved nitrogen was 1.35%-6.32% (n = 6). After the t-test analysis, it does not have the significance difference between this method and national standard method. It is suitable for fast analysis of total dissolved nitrogen in seawater.

Molybdenum Enrichment in the 3.2 Ga old Black Shales Recovered by Dixon Island-Cleaverville Drilling Project (DXCL-DP) in Northwestern Pilbara, Western Australia

NASA Astrophysics Data System (ADS)

Yamaguchi, K. E.; Kiyokawa, S.; Naraoka, H.; Ikehara, M.; Ito, T.; Suganuma, Y.; Sakamoto, R.; Hosoi, K.

2010-12-01

To obtain drillcores of Mesoarchean black shales with negligible modern weathering, we conducted continental drilling at Cleaverville coast in Pilbara, Western Australia. We recovered 3.2Ga sulfidic black shales of the Cleaverville Group from three drillholes (~200m in total), namely DX, CL1, and CL2. Information on the geology of the drilling site has been reported [1, 2]. Here we report the discovery of Mo enrichment in the 3.2Ga DXCL-DP black shales. We analyzed total chemical compositions of forty black shale samples from drillcore DX and fifty-six of those from CL1 and CL2. Molybdenum concentrations for DX samples ranged from 0.3 to 12.9ppm (Avg±1σ= 1.8±1.9ppm), and those for CL1 and CL2 (combined) ranged from 0.8 to 3.3ppm (Avg±1σ= 1.4±0.4ppm). The highest concentration of Mo occurs in Corg-rich sample, and is comparable to that of the contemporaneous Fig Tree Group in South Africa [3, 4]. The highest concentration of Mo in the DXCL-DP samples, ~13ppm, is lower than that found in the 2.5 Ga Mt. McRae Shale of the Hamersley Group, Western Australia (maximums are ~17ppm [5], and ~40ppm [6]). However, it is much higher, by thirteen times, than the average Mo concentration in the Phanerozoic shales (1ppm [7]). No significant enrichment of Mo was expected to occur in the before-GOE black shales if pO2 was as low as <10-6 PAL. Sulfur isotope analysis revealed, based on the variable δ34S values (-1.9 ~ +26.8‰), that bacterial sulfate reduction was so extensive in the 3.2Ga deep marine environments that sulfate utilization by sulfate-reducers was near completion [8]. Production of bacteriogenic sulfide would have enhanced fixation of dissolved Mo into sulfide minerals in sediments. This is rather a common process occurring in oxygen-depleted environments in the modern ocean ([9]). A combined enrichment of Mo, Corg, and S, together with high δ34S values for a sedimentary formation may be used as a strong evidence for operation of modern-day style sedimentary Mo enrichment. This further implies that oxygenation of the atmosphere and (at least the surface) oceans was significant during deposition of the sediments, ~800Ma earlier than commonly thought ([10]). Operation of present-day style geochemical cycle of Mo in the Mesoarchean surface environments suggests early evolution of atmosphere, oceans, and microbial biosphere. References: [1] Kiyokawa et al, 2006, GSAB 118: 3-22. [2] Yamaguchi et al, 2009, Sci. Drill. 7: 34-37. [3] Yamaguchi, 2002, Ph.D. dissertation, Penn State Univ. [4] Yamaguchi & Ohmoto, 2002, GSA Abstract [5] Naraoka et al, 2001, 4th Int'l Archaean Symp., Perth. [6] Anbar et al, 2007, Science 317: 1903-1906. [7] Vine & Tourtelot, 1970, Econ. Geol. 65: 253-272. [8] Sakamoto et al, 2010, Fall AGU Mtg. [9] Morford & Emerson, 1999, GCA 63: 1735-1750. [10] Bekker et al, 2004, Nature 427: 117-120.

Gamma-amino butyric acid (GABA) synthesis of Lactobacillus in fermentation of defatted rice bran extract

NASA Astrophysics Data System (ADS)

Dat, Lai Quoc; Ngan, Tran Thi Kim; Nu, Nguyen Thi Xuan

2017-09-01

This research focused on the synthesis of GABA by Lactobacillus bacteria in fermentation of defatted rice bran extract without adding glutamate. Two strains of Lactobacillus were investigated into capacity of GABA synthesis. Result indicates that, Lactobacillus brevis VTCC - B - 454 exhibited the higher capacity of GABA synthesis in fermentation of defatted rice bran extract than that of Lactobacillus plantarum VTCC - B - 890. Total dissolved solid (TDS), free amino acids (AA) and reducing sugar (RS) contents in fermentation of defatted rice bran extract with two strains also significantly decreased. At pH 5 and 9 %w/w of TDS content in defatted rice bran extract, Lactobacillus brevis VTCC - B - 454 accumulated 2,952 ppm of GABA in 24 hours of fermentation. The result implies that fermentation with Lactobacillus brevis VTCC - B - 454 can be applied for GABA production from defatted rice bran extract.

Determination of total tin in geological materials by electrothermal atomic-absorption spectrophotometry using a tungsten-impregnated graphite furnace

USGS Publications Warehouse

Zhou, L.; Chao, T.T.; Meier, A.L.

1984-01-01

An electrothermal atomic-absorption spectrophotometric method is described for the determination of total tin in geological materials, with use of a tungsten-impregnated graphite furnace. The sample is decomposed by fusion with lithium metaborate and the melt is dissolved in 10% hydrochloric acid. Tin is then extracted into trioctylphosphine oxide-methyl isobutyl ketone prior to atomization. Impregnation of the furnace with a sodium tungstate solution increases the sensitivity of the determination and improves the precision of the results. The limits of determination are 0.5-20 ppm of tin in the sample. Higher tin values can be determined by dilution of the extract. Replicate analyses of eighteen geological reference samples with diverse matrices gave relative standard deviations ranging from 2.0 to 10.8% with an average of 4.6%. Average tin values for reference samples were in general agreement with, but more precise than, those reported by others. Apparent recoveries of tin added to various samples ranged from 95 to 111% with an average of 102%. ?? 1984.

Dry (Mg,Fe)SiO 3 perovskite in the Earth's lower mantle

DOE PAGES

Panero, Wendy R.; Pigott, Jeffrey S.; Reaman, Daniel M.; ...

2015-02-26

Combined synthesis experiments and first-principles calculations show that MgSiO 3-perovskite with minor Al or Fe does not incorporate significant OH under lower mantle conditions. Perovskite, stishovite, and residual melt were synthesized from natural Bamble enstatite samples (Mg/(Fe+Mg) = 0.89 and 0.93; Al 2O 3 < 0.1 wt% with 35 and 2065 ppm wt H 2O, respectively) in the laser-heated diamond anvil cell at 1600-2000 K and 25-65 GPa. Combined Fourier transform infrared (FTIR) spectroscopy, x-ray diffraction, and ex-situ transmission electron microscopy (TEM) analysis demonstrates little difference in the resulting perovskite as a function of initial water content. Four distinct OHmore » vibrational stretching bands are evident upon cooling below 100 K (3576, 3378, 3274, and 3078 cm -1), suggesting 4 potential bonding sites for OH in perovskite with a maximum water content of 220 ppm wt H 2O, and likely no more than 10 ppm wt H 2O. Complementary, Fe-free, first-principles calculations predict multiple potential bonding sites for hydrogen in perovskite, each with significant solution enthalpy (0.2 eV/defect). We calculate that perovskite can dissolve less than 37 ppm wt H 2O (400 ppm H/Si) at the top of the lower mantle, decreasing to 31 ppm wt H 2O (340 ppm H/Si) at 125 GPa and 3000 K in the absence of a melt or fluid phase. Here, we propose that these results resolve a long-standing debate of the perovskite melting curve and explain the order of magnitude increase in viscosity from upper to lower mantle.« less

Water Content of the Oceanic Lithosphere at Hawaii from FTIR Analysis of Peridotite Xenoliths

NASA Technical Reports Server (NTRS)

Peslier, Anne H.; Bizmis, Michael

2013-01-01

Although water in the mantle is mostly present as trace H dissolved in minerals, it has a large influence on its melting and rheological properties. The water content of the mantle lithosphere beneath continents is better constrained by abundant mantle xenolith data than beneath oceans where it is mainly inferred from MORB glass analysis. Using Fourier transform infrared (FTIR) spectrometry, we determined the water content of olivine (Ol), clinopyroxene (Cpx) and orthopyroxene (Opx) in spinel peridotite xenoliths from Salt Lake Crater, Oahu, Hawaii, which are thought to represent fragments of the Pacific oceanic lithosphere that was refertilized by alkalic Hawaiian melts. Only Ol exhibits H diffusion profiles, evidence of limited H loss during xenolith transport to the surface. Water concentrations (Ol: 9-28 ppm H2O, Cpx: 246-566 ppm H2O, Opx: 116-224 ppm H2O) are within the range of those from continental settings but higher than those from Gakkel ridge abyssal peridotites. The Opx H2O contents are similar to those of abyssal peridotites from Atlantic ridge Leg 153 (170-230 ppm) but higher than those from Leg 209 (10- 14 ppm). The calculated bulk peridotite water contents (94 to 144 ppm H2O) are in agreement with MORB mantle source water estimates and lower than estimates for the source of Hawaiian rejuvenated volcanism (approx 540 ppm H2O) . The water content of Cpx and most Opx correlates negatively with spinel Cr#, and positively with pyroxene Al and HREE contents. This is qualitatively consistent with the partitioning of H into the melt during partial melting, but the water contents are too high for the degree of melting these peridotites experienced. Melts in equilibrium with xenolith minerals have H2O/Ce ratios similar to those of OIB

Speciation And Uptake of Arsenic Accumulated By Corn Seedlings Using XAS And DRC-ICP-MS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parsons, J.G.; Martinez-Martinez, A.; Peralta-Videa, J.R.

ICP-MS was used to investigate the uptake of As(III) and As(V) from hydroponics growth media by corn seedlings. It was found that arsenic uptake by the plant roots for the arsenic(V) and arsenic(III) treatments were 95 and 112 ppm, respectively. However, in the shoots of the arsenic (V) treatments had 18 ppm whereas arsenic(III) treatments had 12 ppm. XANES studies showed that As for both treatments arsenic was present as a mixture of an As(III) sulfur complex and an As(V) oxygen complex. The XANES data was corroborated by the EXAFS studies showing the presence of both oxygen and sulfur ligandsmore » coordinated to the arsenic. Iron concentrations were found to increase by 4 fold in the As(V) contaminated growth media and 7 fold in the As(III) treatment compared to the control iron concentration of 500 ppm. Whereas, the total iron concentration in the shoots was found to decrease by approximately the same amount for both treatments from 360 ppm in the control to approximately 125 ppm in both arsenic treatments. Phosphorus concentrations were found to decrease in both the roots and shoots compared to the control plants. The total sulfur in the roots was found to increase in the arsenic(III) and arsenic(V) treatments to 560 ppm and 800 ppm, respectively, compared to the control plants 358 ppm. In addition, the total sulfur in shoots of the plants was found to remain relatively constant at approximately 1080 ppm. The potassium concentrations in the plants were found to increase in the roots and decrease in the shoots.« less

Cavitation Inception in Separated Flows.

DTIC Science & Technology

1981-12-01

measured data. Keller (1972, 1973) determined the nuclei population by using a single particle light scattering device (the sample volume was... computations of the average pressure coefficient. The amount of air dissolved in the water varied from 10 to 11 ppm ( molar ) and was measured with a Van Slyke...fluctuating pressures were also measured. .-The conditions for cavitation inception and desinence were determined and several holograms were recorded

Impact of the hydrogen partial pressure on lactate degradation in a coculture of Desulfovibrio sp. G11 and Methanobrevibacter arboriphilus DH1.

PubMed

Junicke, H; Feldman, H; van Loosdrecht, M C M; Kleerebezem, R

2015-04-01

In this study, the impact of the hydrogen partial pressure on lactate degradation was investigated in a coculture of Desulfovibrio sp. G11 and Methanobrevibacter arboriphilus DH1. To impose a change of the hydrogen partial pressure, formate was added to the reactor. Hydrogen results from the bioconversion of formate besides lactate in the liquid phase. In the presence of a hydrogen-consuming methanogen, this approach allows for a better estimation of low dissolved hydrogen concentrations than under conditions where hydrogen is supplied externally from the gas phase, resulting in a more accurate determination of kinetic parameters. A change of the hydrogen partial pressure from 1,200 to 250 ppm resulted in a threefold increase of the biomass-specific lactate consumption rate. The 50 % inhibition constant of hydrogen on lactate degradation was determined as 0.692 ± 0.064 μM dissolved hydrogen (831 ± 77 ppm hydrogen in the gas phase). Moreover, for the first time, the maximum biomass-specific lactate consumption rate of Desulfovibrio sp. G11 (0.083 ± 0.006 mol-Lac/mol-XG11/h) and the affinity constant for hydrogen uptake of Methanobrevibacter arboriphilus DH1 (0.601 ± 0.022 μM dissolved hydrogen) were determined. Contrary to the widely established view that the biomass-specific growth rate of a methanogenic coculture is determined by the hydrogen-utilizing partner; here, it was found that the hydrogen-producing bacterium determined the biomass-specific growth rate of the coculture grown on lactate and formate.

[Physicochemical composition of bottled drinking water marketed in Ouagadougou (Burkina Faso)].

PubMed

Some, Issa Touridomon; Banao, Issouf; Gouado, Inocent; Tapsoba, Théophile Lincoln

2009-01-01

The bottled drinking water marketed in urban areas includes natural mineral water, spring water, and treated drinking water. Their physicochemical qualities depend on the type and quantity of their components and define their safe use. Bottled water is widely consumed in Ouagadougou (Burkina Faso), and many brand names exist. Although many publications have examined the microbiological qualities of such water, no study has examined the physicochemical quality of water from Burkina Faso. This study, conducted from March 2005 through January 2006, aimed to assess the physicochemical composition of drinking water sold in Ouagadougou to facilitate better choices and use by consumers. Results showed that all the water analyzed in Ouagadougou is soft (TH < 50 ppm) or moderately soft (50 < TH < 200 ppm) and weakly mineralized (total dissolved solid content < 500 mg/L, sulfates [SO(2-)(4)] < 200 mg/L, [Ca(++)] < 150 mg/L, [Mg(2+)] < 50 mg/L, and [HCO(3)-] < 600 mg/l). Some imported water, however, is hard and highly mineralized. French standards do not set limit values for the natural mineral water parameters described above, and much of the water sold in Ouagadougou was natural mineral water. The spring water met potability standards, except for the Montagne d'Arrée brand, which had a pH value of 5.8, below the WHO standards of 6.5 < pH 8.5.

Assessment of desalination technologies for treatment of a highly saline brine from a potential CO 2 storage site

DOE PAGES

Kaplan, Ruth; Mamrosh, Darryl; Salih, Hafiz H.; ...

2016-11-12

Brine extraction is a promising strategy for the management of increased reservoir pressure, resulting from carbon dioxide (CO 2) injection in deep saline reservoirs. The extracted brines usually have high concentrations of total dissolved solids (TDS) and various contaminants, and require proper disposal or treatment. In this article, first by conducting a critical review, we evaluate the applicability, limits, and advantages or challenges of various commercially available and emerging desalination technologies that can potentially be employed to treat the highly saline brine (with TDS values >70.000 ppm) and those that are applicable to a ~200,000 ppm TDS brine extracted frommore » the Mt. Simon Sandstone, a potential CO 2 storage site in Illinois, USA. Based on the side-by-side comparison of technologies, evaporators are selected as the most suitable existing technology for treating Mt. Simon brine. Process simulations are then conducted for a conceptual design for desalination of 454 m 3/h (2000 gpm) pretreated brine for near-zero liquid discharge by multi-effect evaporators. In conclusion, the thermal energy demand is estimated at 246kWh perm 3 of recoveredwater, ofwhich 212kWh/m 3 is required for multiple-effect evaporation and the remainder for salt drying. The process also requires additional electrical power of ~2 kWh/m 3.« less

Assessing the application and downstream effects of pulsed mode ultrasound as a pre-treatment for alum coagulation.

PubMed

Al-Juboori, Raed A; Aravinthan, Vasantha; Yusaf, Talal; Bowtell, Leslie

2016-07-01

The application of pulsed mode ultrasound (PMU) as a pre-treatment for alum coagulation was investigated at various alum dosages and pH levels. The effects of the treatments on turbidity and dissolved organic carbon (DOC) removal and residual Al were evaluated. Response surface methodology (RSM) was utilized to optimize the operating conditions of the applied treatments. The results showed that PMU pre-treatment increased turbidity and DOC removal percentages from maximum of 96.6% and 43% to 98.8% and 52%, respectively. It also helped decrease the minimum residual Al from 0.100 to 0.094 ppm. The multiple response optimization was carried out using the desirability function. A desirability value of >0.97 estimated respective turbidity removal, DOC removal and Al residual of 89.24%, 45.66% and ∼ 0.1 ppm for coagulation (control) and 90.61%, >55% and ∼ 0 for coagulation preceded by PMU. These figures were validated via confirmatory experiments. PMU pre-treatment increased total coliform removal from 80% to >98% and decreased trihalomethane formation potential (THMFP) from 250 to 200 ppb CH3Cl. Additionally, PMU application prior to coagulation improved the settleability of sludge due to the degassing effects. The results of this study confirms that PMU pre-treatment can significantly improve coagulation performance. Copyright © 2015 Elsevier B.V. All rights reserved.

Controls of Methane Dynamics and Emissions in an Arctic Warming Experiment

NASA Astrophysics Data System (ADS)

Nielsen, C. S.; Elberling, B.; Michelsen, A.; Strobel, B. W.; Wulff, K.; Banyasz, I.

2015-12-01

Climatic changes have resulted in increasing air temperatures across the Arctic. This may increase anaerobic decomposition of soil organic matter to methane (CH4) in wetlands and increase plant growth and thereby production of substrate. Little is known about how seasonal variations in dissolved CH4 in soil water, substrate availability, and the effect of warming affect arctic wetland dynamics of CH4 production and emission. In 2013 we established two experiments in a fen at Disko Island, W Greenland; one with year round warming by open-top chambers and removal of shrubs, and one with removal of the aerenchymatous sedge Carex aquatilis ssp. stans. Throughout the growing season 2014 we measured how the treatments affected CH4 emissions, dissolved CH4 in the soil water, and substrate availability. Ecosystem CH4 emissions peaked at August 5th 2014 (7.5 μmol m-2 h-1) without coinciding with time of highest concentrations of dissolved CH4 or acetate indicating a decoupling between production and emission of CH4. The peak in dissolved CH4 concentration, at ten cm depth (1368 ppm, September 18th 2014), followed the peak in concentration of acetate in the same depth (0.30 ppm, August 30th 2014) highlighting the importance of this substance as a substrate for methanogenesis. C. aquatilis ssp. stans accounted for 60% and 77% of the ecosystem CH4 emissions in areas of the fen with water table above and below soil surface showing the importance of the presence of this species to serve as a pipe for CH4 emission which is bypassing the upper soil zone and potential methane oxidation. Throughout the season, warming increased the air temperature at soil surface by on average 0.89°C and occasionally warming and shrub removal increased soil temperature in 2 and 5 cm depth, but there was no effect of the treatments on the CH4 emissions indicating that this wetland is quite resilient towards future climate change.

Mobility of iridium in terrestrial environments: Implications for the interpretation of impact-related mass-extinctions

NASA Astrophysics Data System (ADS)

Martín-Peinado, F. J.; Rodríguez-Tovar, F. J.

2010-08-01

Traditionally, iridium has been considered an element of low mobility, but its behavior is still debated. Ir concentration in a soil affected by a catastrophic mining spill in 1998 that covered the soil with a layer of tailings offers the opportunity to analyse an exceptional Ir-bearing horizon 10 years after deposition. This has enabled comparisons with the values of past Ir-bearing horizons associated to impact-related mass-extinction events. Iridium concentration in the tailings (0.349 ppm) was 5-fold higher than the anomaly in the K-Pg at The Moody Creek Mine section (the highest values obtained from terrestrial sections). The oxidative weathering of the tailings caused the release of Ir and infiltration into the soil. Iridium distribution in depth indicates redistribution throughout the profile in relation to the change in the physico-chemical properties of the soil. With regard to the background concentration in the soil (0.056 ppm), anomalous values of Ir (0.129 ppm) can be detected to 11 cm below the layer of tailings. The correlation analysis between the Ir concentration and the main properties and constituents of the soils indicated a significant correlation with sulfur, iron, clay content, and pH. Selective extractions were made to study the forms in which Ir can be mobilized in the soil. The residual/insoluble fraction was >90% of the total Ir concentration in soil. Soluble-in-water concentration of Ir (1.5% of total) was detected in the uppermost 2-3 cm of the soil, which were directly affected by the leaching of acidic waters coming from the oxidation of the pyrite tailings. Iridium retention in the affected part of the soil reached 9% of the total Ir concentration; this retention could be related to the amorphous iron forms dissolved by the oxalic-oxalate extraction. However, according to our research, original Ir abundance could be secondarily modified, and then a direct analysis of the iridium values recorded in sediments could induce misinterpretations. The comparison between the actual example and the fossil record belonging to terrestrial settings, can be considered as a valuable approach, especially when Iridium data were used by researchers to interpret the impact-related mass-extinction events in the past.

A Study on the Corrosion Behavior of Carbon Steel Exposed to a H2S-Containing NH4Cl Medium

NASA Astrophysics Data System (ADS)

Wang, Hai-bo; Li, Yun; Cheng, Guang-xu; Wu, Wei; Zhang, Yao-heng

2018-05-01

NH4Cl corrosion failure often occurs in the overhead systems of hydrotreaters, and this failure is always accompanied by the appearance of H2S. A combination of electrochemical and surface spectroscopic (SEM/EDS, AFM, XRD) techniques was used to investigate the effect of different factors, including the surface roughness, temperature, dissolved oxygen, pH and H2S concentration, on the corrosion behavior of carbon steel in an NH4Cl environment with the presence of H2S. The effect of H2S concentrations (at the ppm level) on the corrosion behavior of carbon steel was systematically revealed. The experimental results clearly indicated that the corrosion rate reached a minimum value at 10 ppm H2S. The steel surface was covered by a uniform corrosion product film in a 10 ppm H2S environment, and the corrosion product film was tight and protective. The ammonia from NH4Cl helped maintaining the protectiveness of the corrosion films in this environment. Dissolved oxygen mainly accelerated the cathodic reaction. The cathodic limiting current density increased with increasing temperature, and the anodic branch polarization curves were similar at different temperatures. The anodic current density decreased as the pH decreased, and the cathodic current density increased as the pH decreased. The absolute surface roughness ( R a) of carbon steel increased from 132.856 nm at 72 h to 153.973 nm at 144 h, and the rougher surface resulted in a higher corrosion rate. The critical innovation in this research was that multiple influential factors were revealed in the NH4Cl environment with the presence of H2S.

A Study on the Corrosion Behavior of Carbon Steel Exposed to a H2S-Containing NH4Cl Medium

NASA Astrophysics Data System (ADS)

Wang, Hai-bo; Li, Yun; Cheng, Guang-xu; Wu, Wei; Zhang, Yao-heng

2018-04-01

NH4Cl corrosion failure often occurs in the overhead systems of hydrotreaters, and this failure is always accompanied by the appearance of H2S. A combination of electrochemical and surface spectroscopic (SEM/EDS, AFM, XRD) techniques was used to investigate the effect of different factors, including the surface roughness, temperature, dissolved oxygen, pH and H2S concentration, on the corrosion behavior of carbon steel in an NH4Cl environment with the presence of H2S. The effect of H2S concentrations (at the ppm level) on the corrosion behavior of carbon steel was systematically revealed. The experimental results clearly indicated that the corrosion rate reached a minimum value at 10 ppm H2S. The steel surface was covered by a uniform corrosion product film in a 10 ppm H2S environment, and the corrosion product film was tight and protective. The ammonia from NH4Cl helped maintaining the protectiveness of the corrosion films in this environment. Dissolved oxygen mainly accelerated the cathodic reaction. The cathodic limiting current density increased with increasing temperature, and the anodic branch polarization curves were similar at different temperatures. The anodic current density decreased as the pH decreased, and the cathodic current density increased as the pH decreased. The absolute surface roughness (R a) of carbon steel increased from 132.856 nm at 72 h to 153.973 nm at 144 h, and the rougher surface resulted in a higher corrosion rate. The critical innovation in this research was that multiple influential factors were revealed in the NH4Cl environment with the presence of H2S.

Skylab study of water quality. [Kansas

NASA Technical Reports Server (NTRS)

Yarger, H. L. (Principal Investigator); Mccauley, J. R.

1975-01-01

The author has identified the following significant results. Apparent reflectance levels in the Skylab S190A and S192 bands, from one pass over three Kansas reservoirs, exhibit good statistical correlation with suspended solids. Band ratios appear to yield the best results. The concentration of suspended solids, mostly inorganic sediment, has the most effect on the reflected energy. Dissolved solids concentrations up to 200 ppm were not detectable by the Skylab sensors.

Microwave assisted synthesis, characterization and biocidal activities of some new chelates of carbazole derived Schiff bases of cadmium and tin metals

NASA Astrophysics Data System (ADS)

Yadav, Manju; Mishra, Neelima; Sharma, Nutan; Chandra, Sulekh; Kumar, Dinesh

2014-11-01

This study is planned to report the advancement of green microwave approach in the fabrication of a new series of biologically potent (N^X, where X = O/S) donor Schiff bases and their cadmium(II) and tin(II) complexes. The ligands and their metal complexes have been characterized in terms of elemental analysis, molar ionic conductance, magnetic moment and spectral (IR, UV-Vis, NMR (1H, 119Sn), FAB-mass, thermal and XRD) data. The data revealed that the ligands coordinated to the metal center via nitrogen and oxygen/sulfur atoms and form an octahedral arrangement of the ligands around central metal atom. All compounds were evaluated for their in vitro antimicrobial activities against two pathogenic bacteria Bacillus subtilis and Escherichia coli and two fungi Aspergillus niger and Aspergillus flavus by standard disc diffusion method. The discs were stored in an incubator at 37 °C. The compounds were dissolved in DMF at 500 and 1000 ppm concentrations for screening biocidal activity. The compounds were dissolved in DMF to get the 100 and 200 ppm concentration of test solutions for screening fungicidal activity. The inhibition zone around each disc was measured (in mm) after 24 h and 96 h for biocidal and fungicidal activities respectively.

Cadmium accumulation in zebrafish (Danio rerio) eggs is modulated by dissolved organic matter (DOM).

PubMed

Burnison, B Kent; Meinelt, Thomas; Playle, Richard; Pietrock, Michael; Wienke, Andreas; Steinberg, Christian E W

2006-08-23

Experiments were conducted to investigate factors influencing the accumulation of cadmium (Cd(2+)) into zebrafish (Danio rerio) eggs. The accumulation of (109)Cd was affected by: (1) concentration, (2) time, (3) presence of dissolved organic material (DOM), (4) different origin of DOM and (5) different parts of fish eggs. Over a 5-h exposure, zebrafish eggs showed a steady increase in Cd-accumulation. DOM-concentrations over 15ppm carbon (C) decreased Cd-uptake significantly. Both samples of DOM, brown water marsh (LM) and a eutrophic pond (SP), at 16.9ppmC, reduced the Cd-accumulation in the chorion, perivitelline liquid and the embryo. Cd was mainly accumulated in the egg's outer shell chorion (61%) and only small amounts passed through the chorion into the perivitelline liquid (38%) and embryo (1%). In the presence of LM-DOM, the accumulation of Cd into the egg components was decreased by 43% (chorion), 52% (perivitelline liquid) and 52% (embryo), respectively, compared with the control group. Similarly, the presence of SP-DOM reduced the Cd-accumulation by 29% (chorion), 61% (perivitelline liquid) and 60% (embryo), respectively, compared with the controls. DOM-concentration should be taken into consideration when determining ecotoxicological effects of Cd on fish populations.

Petroleum Quality Information System 2013 Annual Report

DTIC Science & Technology

2013-01-01

Content: (ppm) 10 0.10 Metals : (ppm) 0.5 total 0.10 Alkali Metals and Metalloids: (ppm) 1 total 0.99 Table 3-12 displays Direct Sugar to ...183 146 189 185 111 143 0 50 100 150 200 250 300 350 400 450 2005 2006 2007 2008 2009 2010 2011 2012 2013 To ta l S am pl es Calendar Year In-Line...Report Documentation Page Form ApprovedOMB No. 0704-0188 Public reporting burden for the collection of information is estimated to average 1 hour

Evaluation of Chlorine Treatment Levels for Inactivation of Human Norovirus and MS2 Bacteriophage during Sewage Treatment.

PubMed

Kingsley, David H; Fay, Johnna P; Calci, Kevin; Pouillot, Régis; Woods, Jacquelina; Chen, Haiqiang; Niemira, Brendan A; Van Doren, Jane M

2017-12-01

This study examined the inactivation of human norovirus (HuNoV) GI.1 and GII.4 by chlorine under conditions mimicking sewage treatment. Using a porcine gastric mucin-magnetic bead (PGM-MB) assay, no statistically significant loss in HuNoV binding (inactivation) was observed for secondary effluent treatments of ≤25 ppm total chlorine; for both strains, 50 and 100 ppm treatments resulted in ≤0.8-log 10 unit and ≥3.9-log 10 unit reductions, respectively. Treatments of 10, 25, 50, and 100 ppm chlorine inactivated 0.31, 1.35, >5, and >5 log 10 units, respectively, of the norovirus indicator MS2 bacteriophage. Evaluation of treatment time indicated that the vast majority of MS2 and HuNoV inactivation occurred in the first 5 min for 0.2-μm-filtered, prechlorinated secondary effluent. Free chlorine measurements of secondary effluent seeded with MS2 and HuNoV demonstrated substantial oxidative burdens. With 25, 50, and 100 ppm treatments, free chlorine levels after 5 min of exposure ranged from 0.21 to 0.58 ppm, from 0.28 to 16.7 ppm, and from 11.6 to 53 ppm, respectively. At chlorine treatment levels of >50 ppm, statistically significant differences were observed between reductions for PGM-MB-bound HuNoV (potentially infectious) particles and those for unbound (noninfectious) HuNoV particles or total norovirus particles. While results suggested that MS2 and HuNoV (measured as PGM-MB binding) behave similarly, although not identically, both have limited susceptibility to chlorine treatments of ≤25 ppm total chlorine. Since sewage treatment is performed at ≤25 ppm total chlorine, targeting free chlorine levels of 0.5 to 1.0 ppm, these results suggest that traditional chlorine-based sewage treatment does not inactivate HuNoV efficiently. IMPORTANCE HuNoV is ubiquitous in sewage. A receptor binding assay was used to assess inactivation of HuNoV by chlorine-based sewage treatment, given that the virus cannot be routinely propagated in vitro Results reported here indicate that chlorine treatment of sewage is not effective for inactivating HuNoV unless chlorine levels are above those routinely used for sewage treatment. Copyright © 2017 American Society for Microbiology.

Evaluation of Chlorine Treatment Levels for Inactivation of Human Norovirus and MS2 Bacteriophage during Sewage Treatment

PubMed Central

Fay, Johnna P.; Calci, Kevin; Pouillot, Régis; Woods, Jacquelina; Chen, Haiqiang; Niemira, Brendan A.; Van Doren, Jane M.

2017-01-01

ABSTRACT This study examined the inactivation of human norovirus (HuNoV) GI.1 and GII.4 by chlorine under conditions mimicking sewage treatment. Using a porcine gastric mucin-magnetic bead (PGM-MB) assay, no statistically significant loss in HuNoV binding (inactivation) was observed for secondary effluent treatments of ≤25 ppm total chlorine; for both strains, 50 and 100 ppm treatments resulted in ≤0.8-log10 unit and ≥3.9-log10 unit reductions, respectively. Treatments of 10, 25, 50, and 100 ppm chlorine inactivated 0.31, 1.35, >5, and >5 log10 units, respectively, of the norovirus indicator MS2 bacteriophage. Evaluation of treatment time indicated that the vast majority of MS2 and HuNoV inactivation occurred in the first 5 min for 0.2-μm-filtered, prechlorinated secondary effluent. Free chlorine measurements of secondary effluent seeded with MS2 and HuNoV demonstrated substantial oxidative burdens. With 25, 50, and 100 ppm treatments, free chlorine levels after 5 min of exposure ranged from 0.21 to 0.58 ppm, from 0.28 to 16.7 ppm, and from 11.6 to 53 ppm, respectively. At chlorine treatment levels of >50 ppm, statistically significant differences were observed between reductions for PGM-MB-bound HuNoV (potentially infectious) particles and those for unbound (noninfectious) HuNoV particles or total norovirus particles. While results suggested that MS2 and HuNoV (measured as PGM-MB binding) behave similarly, although not identically, both have limited susceptibility to chlorine treatments of ≤25 ppm total chlorine. Since sewage treatment is performed at ≤25 ppm total chlorine, targeting free chlorine levels of 0.5 to 1.0 ppm, these results suggest that traditional chlorine-based sewage treatment does not inactivate HuNoV efficiently. IMPORTANCE HuNoV is ubiquitous in sewage. A receptor binding assay was used to assess inactivation of HuNoV by chlorine-based sewage treatment, given that the virus cannot be routinely propagated in vitro. Results reported here indicate that chlorine treatment of sewage is not effective for inactivating HuNoV unless chlorine levels are above those routinely used for sewage treatment. PMID:28939600

Control and distribution of uranium in coral reefs during diagenesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gvirtzman, G.; Friedman, G.M.; Miller, D.S.

1973-12-01

The concentration of about 2 ppM of uranium in the aragonitic skeletons of modern scleractinian corals which we studied is a constant value, regardless of occurrence, anatomy, or taxonomy. The presence of cement of aragonite or high- magnesian calcite usually raises the concentration of bulk samples to about 3 ppM. Modern corals may contain up to 50% of cementing minerals. Organisms, such as corals and coralline algae, while secreting their skeleton, discriminate against the uptake of uranium, whereas the uptake of uranium by mineral cements is less restrained. Aragonite cement contains about 3.6 ppM and highmagnesian calcite cement 2.6 ppMmore » uranium. During leaching by freshwater, the aragonite of the skeletons of corals dissolves out. This creates hollow molds which fill with drusy low-magnesian calcite. In emergent reefs from the shores of the Red Sea which display the ellects of progressive diagenesis this calcite is enriched in uranium (3.9 ppM) beyond that found in marine cements. Second-generation calcite, which fills original voids in the corals from the emergent reefs, contains a lower level of uranium concent ration (1.3 ppM). The level of concentration of uranium in low-magnesian calcite of diagenetically altered corals is a function of the availability of uranium in meteoric waters. In aragonite as well as in high- and low-magnesian calcite uranium replaces calcium or occupies lattice vacancies in the crystal lattice. (auth)« less

Total dissolved gas, barometric pressure, and water temperature data, lower Columbia River, Oregon and Washington, 1996

USGS Publications Warehouse

Tanner, Dwight Q.; Harrison, Howard E.; McKenzie, Stuart W.

1996-01-01

Increased levels of total dissolved gas pressure can cause gas-bubble trauma in fish downstream from dams on the Columbia River. In cooperation with the U.S. Army Corps of Engineers, the U.S. Geological Survey collected data on total dissolved gas pressure, barometric pressure, water temperature, and dissolved oxygen pressure at 11 stations on the lower Columbia River from the John Day forebay (river mile 215.6) to Wauna Mill (river mile 41.9) from March to September 1996. Methods of data collection, review, and processing are described in this report. Summaries of daily minimum, maximum, and mean hourly values are presented for total dissolved gas pressure, barometric pressure, and water temperature. Hourly values for these parameters are presented graphically. Dissolved oxygen data are not presented in this report because the quality-control data show that the data have poor precision and high bias. Suggested changes to monitoring procedures for future studies include (1) improved calibration procedures for total dissolved gas and dissolved oxygen to better define accuracy at elevated levels of supersaturation and (2) equipping dissolved oxygen sensors with stirrers because river velocities at the shoreline monitoring stations probably cannot maintain an adequate flow of water across the membrane surface of the dissolved oxygen sensor.

Expanding malaria diagnosis and treatment in Lao PDR: lessons learned from a public-private mix initiative.

PubMed

Simmalavong, Nouannipha; Phommixay, Sengkham; Kongmanivong, Phoudaliphone; Sichanthongthip, Odai; Hongvangthong, Bouasy; Gopinath, Deyer; Sintasath, David M

2017-11-13

As in other countries of the Greater Mekong Sub-region (GMS), the private health sector constitutes a significant avenue where malaria services are provided and presents a unique opportunity for public-private collaboration. In September 2008, a public-private mix (PPM) strategy was launched initially in four northern and southern provinces in Lao PDR to increase access to rapid diagnostic tests (RDTs) and artemisinin-based combination therapy (ACT), improve quality of care, and collect routine malaria data from the private sector. Throughout the process, key stakeholders were involved in the planning, monitoring and supervision of project sites. Following an initial assessment in 2009, the PPM initiative expanded to an additional 14 district sites to a total of 245 private pharmacies and 16 clinics covering 8 provinces and 22 districts. By June 2016, a total of 317 pharmacies, 30 clinics in 32 districts of the 8 provinces were participating in the PPM network and reported monthly malaria case data. This descriptive study documented the process of initiating and maintaining the PPM network in Lao PDR. Epidemiological data reported through the routine surveillance system from January 2009 to June 2016 were analyzed to illustrate the contribution of case reporting from the private sector. A total of 2,301,676 malaria tests were performed in the PPM districts, which included all the PPM pharmacies and clinics (176,224, 7.7%), proportion of patients tested from 14,102 (4.6%) in 2009 to 29,554 (10.4%) in 2015. Over the same period of 90 months, a total of 246,091 positive cases (10.7%) were detected in PPM pharmacies and clinics (33,565; 13.6%), in the same districts as the PPM sites. The results suggest that the PPM sites contributed to a significant increasing proportion of patients positive for malaria from 1687 (7.4%) in 2009 to 5697 (15.8%) in 2015. Ensuring adequate and timely supplies of RDTs and ACT to PPM sites is critical. Frequent refresher training is necessary to maintain data quality, motivation and feedback. In the context of malaria elimination, the PPM initiative should be expanded further to ensure that all febrile cases seen through the private sector in malaria transmission areas are tested for malaria and treated appropriately. Results from the PPM must be integrated into a centralized registry of malaria cases that should prompt required case and foci investigations and responses to be conducted as part of elimination efforts.

Phenolic constituents of shea (Vitellaria paradoxa) kernels.

PubMed

Maranz, Steven; Wiesman, Zeev; Garti, Nissim

2003-10-08

Analysis of the phenolic constituents of shea (Vitellaria paradoxa) kernels by LC-MS revealed eight catechin compounds-gallic acid, catechin, epicatechin, epicatechin gallate, gallocatechin, epigallocatechin, gallocatechin gallate, and epigallocatechin gallate-as well as quercetin and trans-cinnamic acid. The mean kernel content of the eight catechin compounds was 4000 ppm (0.4% of kernel dry weight), with a 2100-9500 ppm range. Comparison of the profiles of the six major catechins from 40 Vitellaria provenances from 10 African countries showed that the relative proportions of these compounds varied from region to region. Gallic acid was the major phenolic compound, comprising an average of 27% of the measured total phenols and exceeding 70% in some populations. Colorimetric analysis (101 samples) of total polyphenols extracted from shea butter into hexane gave an average of 97 ppm, with the values for different provenances varying between 62 and 135 ppm of total polyphenols.

Effects of methyl mercury on reproduction in American kestrels

USGS Publications Warehouse

Albers, P.H.; Koterba, M.T.; Rossmann, R.; French, J.B.; Bennett, R.S.; Bauer, W.C.; Link, W.A.

2006-01-01

Methyl mercury (MeHg) readily passes through biological membranes, accumulates in individuals, and biomagnifies in higher order predators. It is acutely toxic to some birds at 5-15 parts per million (ppm) wet weight in the diet, and it can damage the central nervous system, impair reproduction, and retard growth and development. The effects of MeHg on reproduction in wild raptors are poorly known, and experiments with captive raptors have not included measures of reproductive response. In this study, breeding pairs of captive American kestrels (Falco sparverius) were exposed to environmentally realistic concentrations of MeHg in the diet and their subsequent reproduction was measured. Egg production, incubation performance, and the number of eggs hatched markedly decreased between 3.2 and 4.6 ppm MeHg dry weight in the diet. The percent of eggs hatched declined between 0.75 and 2 ppm MeHg dry weight in the diet and further declined to almost total hatching failure between 3.2 and 4.6 ppm. The number of fledglings and the percent of nestlings fledged were greatly reduced at 0.75 ppm MeHg dry weight in the diet and began a final sharp decline between 2 and 3.2 ppm. Dietary concentrations of > 4.6 ppm MeHg dry weight were associated with total fledging failure. Mercury concentrations in a set of 19 `second-laid? eggs collected from all groups were related to dietary concentrations of MeHg and the reproductive responses of kestrels in each group. Observed percentage declines in fledgling production caused by diets containing >2 ppm MeHg dry weight would result in the production of insufficient numbers of young kestrels for maintenance of wild populations. Concentrations of total Hg in eggs from the highest diet group (5.9 ppm dry weight) were higher than egg concentrations reported for either wild birds or for captive birds fed dry commercial food containing 5 ppm MeHg wet weight.

Simulated sugar factory wastewater remediation kinetics using algal-bacterial raceway reactor promoted by polyacrylate polyalcohol.

PubMed

Memon, Abdul Rehman; Andresen, John; Habib, Muddasar; Jaffar, Muhammad

2014-04-01

The remediation kinetics of simulated sugar factory wastewater (SFW) using an algal-bacterial culture (ABC) of Chlorella vulgaris in association with Pseudomonas putida in a raceway reactor was found to be enhanced by 89% with the addition of 80ppm of copolymer Polyacrylate polyalcohol (PAPA). This was achieved by efficient suspension of the ABC throughout the water body maintaining optimum pH and dissolved oxygen that led to rapid COD removal and improved algal biomass production. The suspension of the ABC using the co-polymer PAPA maintained a DO of 8-10mgl(-1) compared to 2-3mgl(-1) when not suspended. As a result, the non-suspended ABC only achieved a 50% reduction in COD after 96h compared to a 89% COD removal using 80ppm PAPA suspension. In addition, the algae biomass increased from 0.4gl(-1)d(-1) for the non-suspended ABC to 1.1gl(-1)d(-1) when suspended using 80ppm PAPA. Copyright © 2014 Elsevier Ltd. All rights reserved.

SU-E-T-274: Does Atmospheric Oxygen Affect the PRESAGE Dosimeter?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alqathami, M; Ibbott, G; Blencowe, A

Purpose: To experimentally determine the influence of atmospheric oxygen on the efficiency of the PRESAGE dosimeter and its reporting system. Methods: Batches of the reporting system – a mixture of chloroform and leuchomalachite green dye – and PRESAGE were prepared in aerobic and anaerobic conditions. For anaerobic batches, samples were deoxygenated by bubbling nitrogen through the dosimeter precursors or reporting system for 10 min. The dosimeters and reporting systems were prepared in spectrophotometric cuvettes and glass vials, respectively, and were irradiated with 6 MV photons to various radiation doses using a clinical linear accelerator. Changes in optical density of themore » dosimeters and reporting system before and after irradiation were measured using a spectrophotometer. In addition, the concentrations of dissolved oxygen were measured using a dissolved oxygen meter. Results: The experiments revealed that oxygen has little influence on the characteristics of PRESAGE, with the radical initiator oxidizing the leucomalachite green even in the presence of oxygen. However, deoxygenation of the reporting system leads to an increase in sensitivity to radiation dose by ∼ 30% when compared to the non-deoxygenated system. A slight improvement in sensitivity (∼ 5%) was also achieved by deoxygenating the PRESAGE precursor prior to casting. Measurement of the dissolved oxygen revealed low levels (0.4 ppm) in the polyurethane precursor used to fabricate the dosimeters, as compared to water (8.6 ppm). In addition, deoxygenation had no effect on the retention of the post-response absorption value of the PRESAGE dosimeter. Conclusion: The results suggest that the presence of oxygen does not inhibit the radiochromic properties of the PRESAGE system. In addition, there were no observed changes in the dose linearity, absorption spectrum and post-response photofading characteristics of the PRESAGE under the conditions investigated.« less

Characterization of Whole Porewater Dissolved Organic Matter by 1H NMR

NASA Astrophysics Data System (ADS)

Fox, C.; Lewicki, J. P.; Abdulla, H. A.; Burdige, D.; Magen, C.; Chanton, J.; Komada, T.

2014-12-01

Dissolved organic matter (DOM) is a key intermediate in microbial remineralization of organic matter, but only a small percentage of this complex pool has been fully characterized. We present the results of a novel approach to the characterization of DOM in whole porewater samples from the anoxic sediments of the Santa Barbara Basin, California Borderland, using solution state nuclear magnetic resonance (NMR) techniques. Profiles of porewater DOM were obtained by 1H NMR from 95 to 435 cm sediment depth. 1H NMR spectra of each whole porewater sample showed continuous, broad regions from ~0.5 to ~4.5 ppm, indicative of significant signal overlap inherent to complex mixtures, superimposed on a few highly resolved peaks. The individual samples consist of a broad range of chemical environments with varying relative abundances that show a near linear trend with depth. The normalized spectral data were analyzed by principal component analysis to resolve variations in chemical composition of DOM as a function of depth. In addition to detecting the major components such as carbohydrates, cyclic aliphatics and aromatics, our results demonstrate a negative correlation between carbohydrates concurrent with a relative increase in levels of aliphatics. Furthermore, we have identified a decrease in the abundance of alkenes coupled with an increase in a broad region from ~1.9 to ~3.2 ppm, likely corresponding to signals from carboxylic-rich alicyclic molecules. In both trends, the greatest variation occurs between 115 and 135 cm, which straddles the sulfate-methane transition zone (~125 cm), potentially highlighting a region of relatively high DOM transformation. Our work has also identified thiol species which are thought to be formed by dissolved (inorganic) sulfide incorporation into porewater DOM compounds. The implications of these results with respect to carbon cycling in anaerobic sediments will be discussed.

Cationic polyacrylamide enhancing cellulase treatment efficiency of hardwood kraft-based dissolving pulp.

PubMed

Wang, Qiang; Liu, Shanshan; Yang, Guihua; Chen, Jiachuan; Ni, Yonghao

2015-05-01

Cellulase treatment for decreasing viscosity and increasing Fock reactivity of dissolving pulp is a promising approach to reduce the use of toxic chemicals, such as hypochlorite in the dissolving pulp manufacturing process in the industry. Improving the cellulase treatment efficiency during the process is of practical interest. In the present study, the concept of using cationic polyacrylamide (CPAM) to enhance the cellulase treatment efficiency was demonstrated. This was mainly attributed to the increased cellulase adsorption onto cellulose fibers based on the patching/bridging mechanism. Results showed that the cellulase adsorption was increased by about 20% with the addition of 250 ppm of CPAM under the same conditions as those of the control. It was found that the viscosity decrease and Fock reactivity increase for the cellulase treatment was enhanced from using CPAM. The CPAM-assisted cellulase treatment concept may provide a practical alternative to the present hypochlorite-based technology for viscosity control in the industry. Copyright © 2015 Elsevier Ltd. All rights reserved.

Volatiles in basaltic glasses from a subglacial volcano in northern British Columbia (Canada): Implications for ice sheet thickness and mantle volatiles

USGS Publications Warehouse

Dixon, J.E.; Filiberto, J.R.; Moore, J.G.; Hickson, C.J.

2002-01-01

Dissolved H2O, CO2, S and Cl concentrations were measured in glasses from Tanzilla Mountain, a 500 m-high, exposed subglacial volcano from the Tuya-Teslin region, north central British Columbia, Canada. The absence of a flat-topped subaerial lava cap and the dominance of pillows and pillow breccias imply that the Tanzilla Mountain volcanic edifice did not reach a subaerial eruptive phase. Lavas are dominantly tholeiitic basalt with minor amounts of alkalic basalt erupted at the summit and near the base. Tholeiites have roughly constant H2O (c.0.56 ?? 0.07 wt%), CO2 (<30 ppm), S (980 ?? 30 ppm) and Cl (200 ?? 20 ppm) concentrations. Alkalic basalts have higher and more variable volatile concentrations that decrease with increasing elevation (0.62-0.92 wt% H2O, <30 ppm CO2, 870-1110 ppm S and 280-410 ppm Cl) consistent with eruptive degassing. Calculated vapour saturation pressures for the alkalic basalts are 36 to 81 bars corresponding to ice thicknesses of 400 to 900 m. Maximum calculated ice thickness (c. 1 km) is at the lower end of the range of predicted maximum Fraser glaciation (c. 1-2 km), and may indicate initiation of volcanism during the waning stages of glaciation. Temporal evolution from tholeiitic to alkalic compositions may reflect compositional gradients within a melting column, instead of convective processes within a stratified magma chamber. The mantle source region for the subglacial volcanoes is enriched in incompatible elements similar to that for enriched mid-oceanic ridge basalt (e.g. Endeavour Ridge) and does not contain residual amphibole. Thus, metasomatic enrichment most likely reflects small degree partial melts rather than hydrous fluids.

Selenium and Mercury Concentrations in Fish, Wolford Mountain Reservoir, Colorado, 2005

USGS Publications Warehouse

Bauch, Nancy J.

2007-01-01

A reconnaissance investigation of selenium and total mercury in fish in Wolford Mountain Reservoir, Colorado, was conducted by the U.S. Geological Survey in June 2005, in cooperation with the Colorado River Water Conservation District. A total of 32 game and nongame fish were collected from three sites in the reservoir for analysis of selenium and total mercury. Five species of fish were sampled: white sucker (Catostomus commersonii, n=17), brown trout (Salmo trutta, n=5), rainbow trout (Oncorhynchus mykiss, n=5), cutthroat trout (Oncorhynchus clarkii, n=3), and splake (Salvelinus fontinalis x Salvelinus namaycush, n=2). Selenium concentrations ranged from 1.05 to 11.7 micrograms per gram (equivalent to parts per million or ppm) dry weight, whole body. Almost 22 percent (7 of 32) of fish samples had selenium concentrations greater than 7.91 micrograms per gram dry weight, the U.S. Environmental Protection Agency 2004 draft freshwater chronic criterion for selenium in whole-body fish tissue. Total mercury concentrations in muscle plug samples ranged from 0.012 to 0.320 microgram per gram wet weight. Concentrations of mercury in muscle plug samples are comparable to concentrations in fillet samples, and only one fish sample, a nongame white sucker, had a total mercury concentration greater than the U.S. Environmental Protection Agency water-quality criterion for the protection of human health of 0.3 microgram per gram wet weight in fillets. Converting muscle plug or fillet concentrations of mercury to whole-body concentrations, four fish samples (12.5 percent) had estimated whole-body total mercury concentrations greater than 0.1 microgram per gram wet weight concentration in whole-body fish tissue, the U.S. Fish and Wildlife Service criterion for protection of fish-eating birds and wildlife. Water-quality data for dissolved selenium and total mercury in two tributaries and three reservoir sites were compiled and compared. Dissolved concentrations of selenium in one tributary and one reservoir site (prior to 1998) were greater than 4.6 micrograms per liter, the State of Colorado chronic water-quality standard for dissolved selenium for protection of aquatic life. Total mercury concentrations in most water samples from two tributaries and three reservoir sites were less than or equal to 0.01 microgram per liter, the State of Colorado chronic water-quality standard for total mercury for protection of aquatic life. Selenium and mercury in fish in Wolford Mountain Reservoir most likely are not directly related to selenium and mercury concentrations in reservoir water, as most selenium and mercury in fish tissue results from the presence of selenium and mercury in the diet rather than through gill uptake from water. Results of this reconnaissance investigation of selenium and total mercury in fish in Wolford Mountain Reservoir indicate that concentrations of selenium were elevated in some fish. Most total mercury concentrations in fish were less than criteria levels.

Organochlorine contaminants in passeriformes and other avian prey of the peregrine falcon in the western United States

USGS Publications Warehouse

DeWeese, L.R.; McEwen, L.C.; Hensler, G.L.; Petersen, B.E.

1986-01-01

About 1,150 individuals of 38 species of Passeriformes and other small birds were collected in 1980 at 36 locations in eight western U.S. states for organochlorine (OC) chemical analysis. The bird carcasses (less beak, tarsi, gastrointestinal tract, and feathers) were combined by species and location (4 to 15 specimens per sample) into 124 composited samples for analysis. Also analyzed were 77 single specimens of four species, to assess variation in residue concentrations in individual birds. The chemicals detected (greater than 0.05 ppm) were the following (in order of frequency): DDE, polychlorinated biphenyls (PCBs), hexachlorocyclohexane (HCH), heptachlor epoxide, oxychlordane, dieldrin and toxaphene. DDE accounted for 72% of total OC concentrations (ppm DDE/ppm total OCs) overall and PCBs accounted for 3%. DDE mean (geometric) residues were highest in tree swallows (Tachycineta bicolor Vieillot), 12.0 ppm; killdeer (Charadrius vociferus L.), 5.9 ppm; and Brewer's blackbirds (Euphagus cyanocephalus Wagler), 2.7 ppm. Eight migratory species showed mean DDE residues 13 times higher than those in four resident species (1.3 vs. 0.1 ppm, p < 0.05), but PCB residues were similar (0.03 vs. 0.02 ppm). Insectivorous species showed higher DDE, PCB and total OC residues than did either omnivores or granivores (p < 0.05). Males of some species showed higher residues of DDE, PCBs and total OCs than did females (p < 0.05). DDE residues, but not PCBs, in killdeer, Brewer's blackbirds and violet-green swallows (Tachycineta thalassina Swainson) were significantly related (0.01 < p < 0.08) to latitude and longitude of origin. Concentrations of DDE in the carcass fat of some individual tree swallows and killdeer would be in the lethal range if 15 to 20% of the stored DDE were rapidly mobilized to the brain. Samples of 13 species contained DDE concentrations (greater than 3 ppm) considered sufficient to inhibit the normal reproduction of avian predators feeding on them. The evidence suggests that potentially harmful OC concentrations are present in certain western migrants and pose an even greater hazard to avian predators such as the peregrine falcon (Falco peregrinus Tunstall).

Naphthenic acids removal from high TDS produced water by persulfate mediated iron oxide functionalized catalytic membrane, and by nanofiltration.

PubMed

Aher, Ashish; Papp, Joseph; Colburn, Andrew; Wan, Hongyi; Hatakeyama, Evan; Prakash, Prakhar; Weaver, Ben; Bhattacharyya, Dibakar

2017-11-01

Oil industries generate large amounts of produced water containing organic contaminants, such as naphthenic acids (NA) and very high concentrations of inorganic salts. Recovery of potable water from produced water can be highly energy intensive is some cases due to its high salt concentration, and safe discharge is more suitable. Here, we explored catalytic properties of iron oxide (Fe x O y nanoparticles) functionalized membranes in oxidizing NA from water containing high concentrations of total dissolved solids (TDS) using persulfate as an oxidizing agent. Catalytic decomposition of persulfate by Fe x O y functionalized membranes followed pseudo-first order kinetics with an apparent activation energy of 18 Kcal/mol. Fe x O y functionalized membranes were capable of lowering the NA concentrations to less than discharge limits of 10 ppm at 40 °C. Oxidation state of iron during reaction was quantified. Membrane performance was investigated for extended period of time. A coupled process of advanced oxidation catalyzed by membrane and nanofiltration was also evaluated. Commercially available nanofiltration membranes were found capable of retaining NA from water containing high concentrations of dissolved salts. Commercial NF membranes, Dow NF270 (Dow), and NF8 (Nanostone) had NA rejection of 79% and 82%, respectively. Retentate for the nanofiltration was further treated with advanced oxidation catalyzed by Fe x O y functionalized membrane for removal of NA.

Exposure to methyl tert-butyl ether, benzene, and total hydrocarbons at the Singapore-Malaysia causeway immigration checkpoint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan, C.; Ong, H.Y.; Kok, P.W.

1996-12-31

The primary aim of this study was to determine the extent and levels of exposure to volatile organic compounds (VOCs) from automobile emissions in a group of immigration officers at a busy cross-border checkpoint. A majority (80%) of the workers monitored were exposed to benzene at levels between 0.01 and 0.5 ppm, with only 1.2% exceeding the current Occupational Safety and Health Administration occupational exposure limit of 1 ppm. The geometric mean (GM) concentrations of 8-hr time-weighted average exposure were 0.03 ppm, 0.9 ppm, and 2.46 ppm for methyl-tert-butyl ether (MTBE), benzene, and total hydrocarbons (THC), respectively. The highest time-weightedmore » average concentrations measured were 1.05 ppm for MTBE, 2.01 ppm for benzene, and 34 ppm for THC. It was found that motorbikes emitted a more significant amount of pollutants compared with motor cars. On average, officers at the motorcycle booths were exposed to four to five times higher levels of VOCs (GMs of 0.07 ppm, 0.23 ppm, and 4.7 ppm for MTBE, benzene, and THC) than their counterparts at the motor car booths (GMs of 0.01 ppm, 0.05 ppm, and 1.5 ppm). The airborne concentrations of all three pollutants correlated with the flow of vehicle traffic. Close correlations were also noted for the concentrations in ambient air for the three pollutants measured. Benzene and MTBE had a correlation coefficient of 0.97. The overall findings showed that the concentrations of various VOCs were closely related to the traffic density, suggesting that they were from a common source, such as exhaust emissions from the vehicles. The results also indicated that although benzene, MTBE, and THC are known to be volatile, a significant amount could still be detected in the ambient environment, thus contributing to our exposure to these compounds. 4 refs., 6 figs.« less

Controlled environments alter nutrient content of soybeans

NASA Astrophysics Data System (ADS)

Jurgonski, L. J.; Smart, D. J.; Bugbee, B.; Nielsen, S. S.

1997-01-01

Information about compositional changes in plants grown in controlled environments is essential for developing a safe, nutritious diet for a Controlled Ecological Life-Support System (CELSS). Information now is available for some CELSS candidate crops, but detailed information has been lacking for soybeans. To determine the effect of environment on macronutrient and mineral composition of soybeans, plants were grown both in the field and in a controlled environment where the hydroponic nutrient solution, photosynthetic flux (PPF), and CO_2 level were manipulated to achieve rapid growth rates. Plants were harvested at seed maturity, separated into discrete parts, and oven dried prior to chemical analysis. Plant material was analyzed for proximate composition (moisture, protein, lipid, ash, and carbohydrate), total nitrogen (N), nonprotein N (NPN), nitrate, minerals, amino acid composition, and total dietary fiber. The effect of environment on composition varied by cultivar and plant part. Chamber-grown plants generally exhibited the following characteristics compared with field-grown plants: 1) increased total N and protein N for all plant parts, 2) increased nitrate in leaves and stems but not in seeds, 3) increased lipids in seeds, and 4) decreased Ca:P ratio for stems, pods, and leaves. These trends are consistent with data for other CELSS crops. Total N, protein N, and amino acid contents for 350 ppm CO_2 and 1000 ppm CO_2 were similar for seeds, but protein N and amino acid contents for leaves were higher at 350 ppm CO_2 than at 1000 ppm CO_2. Total dietary fiber content of soybean leaves was higher with 350 ppm CO_2 than with 1000 ppm CO_2. Such data will help in selecting of crop species, cultivars, and growing conditions to ensure safe, nutritious diets for CELSS.

Volatile chemicals identified in extracts from leaves of Japanese mugwort (Artemisia princeps pamp.).

PubMed

Umano, K; Hagi, Y; Nakahara, K; Shoji, A; Shibamoto, T

2000-08-01

Extracts from leaves of Japanese mugwort (Artemisia princeps Pamp.) were obtained using two methods: steam distillation under reduced pressure followed by dichloromethane extraction (DRP) and simultaneous purging and extraction (SPSE). A total of 192 volatile chemicals were identified in the extracts obtained by both methods using gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS). They included 47 monoterpenoids (oxygenated monoterpenes), 26 aromatic compounds, 19 aliphatic esters, 18 aliphatic alcohols, 17 monoterpenes (hydrocarbon monoterpenes), 17 sesquiterpenes (hydrocarbon sesquiterpenes), 13 sesquiterpenoids (oxygenated sesquiterpenes), 12 aliphatic aldehydes, 8 aliphatic hydrocarbons, 7 aliphatic ketones, and 9 miscellaneous compounds. The major volatile constituents of the extract by DRP were borneol (10.27 ppm), alpha-thujone (3.49 ppm), artemisia alcohol (2.17 ppm), verbenone (1.85 ppm), yomogi alcohol (1.50 ppm), and germacren-4-ol (1.43 ppm). The major volatile constituents of the extract by SPSE were 1,8-cineole (8.12 ppm), artemisia acetate (4.22 ppm), alpha-thujone (3.20 ppm), beta-caryophyllene (2.39 ppm), bornyl acetate (2.05 ppm), borneol (1.80 ppm), and trans-beta-farnesene (1. 78 ppm).

JPRS Report, Science & Technology, Japan

DTIC Science & Technology

1988-03-03

formation of deoxi- dized products in composite-deoxidized steel ingots M-6 Production of particle-dispersed alloy M-7 Structure and...densities of the OH radicals and C03 2" in the glass as low as possible, while prevent- ing bubble formation . 3. Sound-Wave Floating Furnace The...001 3 March 1988 21 ADVANCED MATERIALS 50. 60 80 ~CaO (mol%) 90 100 unit : ppm nnount oF plitinud dissolved i 2g Dissolution

Solubility of platinum-arsenide melt and sperrylite in synthetic basalt at 0.1 MPa and 1200 °C with implications for arsenic speciation and platinum sequestration in mafic igneous systems

NASA Astrophysics Data System (ADS)

Canali, A. C.; Brenan, J. M.; Sullivan, N. A.

2017-11-01

To better understand the Pt-As association in natural magmas, experiments were done at 1200 °C and 0.1 MPa to measure the solubility of Pt and Pt-arsenide phases (melt and sperrylite, PtAs2), as well as to determine the oxidation state, and identify evidence for Pt-As complexing, in molten silicate. Samples consisting of synthetic basalt contained in chromite crucibles were subject to three experimental procedures. In the first, platinum solubility in the synthetic basalt was determined without added arsenic by equilibrating the sample with a platinum source (embedded wire or bead) in a gas-mixing furnace. In the second, the sample plus a Pt-arsenide source was equilibrated in a vacuum-sealed fused quartz tube containing a solid-oxide oxygen buffer. The third approach involved two steps: first equilibrating the sample in a gas-mixing furnace, then with added arsenide melt in a sealed quartz tube. Oxygen fugacity was estimated in the latter step using chromite/melt partitioning of vanadium. Method two experiments done at high initial arsenic activity (PtAs melt + PtAs2), showed significant loss of arsenic from the sample, the result of vapour transfer to newly-formed arsenide phases in the buffer. Method three experiments showed no loss of arsenic, yielding a uniform final distribution in the sample. Analyses of run-product glasses from experiments which did not show arsenic loss reveal significant increase in arsenic concentrations with fO2, varying from ∼10 ppm (FMQ-3.25) to >10,000 ppm (FMQ + 5.5). Despite very high arsenic loadings (>1000 ppm), the solubility of Pt is similar in arsenic-bearing and arsenic-free glasses. The variation in arsenic solubility with fO2 shows a linear relationship, that when corrected for the change in the activity of dissolved arsenic with the melt ferric/ferrous ratio, yields a solubility-fO2 relationship consistent with As3+ as the dissolved species. This result is confirmed by X-ray absorption near edge structure (XANES) determination on run-product glasses. Levels of arsenic required for Pt-arsenide saturation are 50-500 ppm over the fO2 range of most terrestrial basalts (FMQ to FMQ-2), >100× higher than the arsenic concentrations typical of such magmas, indicating significant enrichment of arsenic is required if Pt-arsenide saturation is to occur. In contrast, the level of dissolved Pt required to saturate in sperrylite is >8× lower than for pure Pt, suggesting that arsenic enrichment could lead to Pt removal at concentrations much less than required for pure metal saturation.

Water requirements of the styrene, butadiene and synthetic-rubber industries

USGS Publications Warehouse

Durfor, Charles N.

1963-01-01

About 710 million gallons of makeup water is withdrawn daily by the styrene, butadiene, styrene-butadiene rubber (SBR), and specialty-rubber industries; 88 percent of this water is used only for once-through cooling. About 429 million gallons of water daily (mgd) is withdrawn by the butadiene industry; 158 ragd is withdrawn by the styrene industry; 94 mgd is used to make special-purpose synthetic rubber; and 29 mgd is used in the direct manufacture of SBR. The amount of makeup water withdrawn to produce SBR ranges from 11,400 to 418,000 gallons per long ton of finished rubber. The amount of makeup water withdrawn depends upon the type of rubber, the processes used to make SBR and its intermediates (styrene and butadiene), and the availability of water at the styrene, butadiene, and SBR plants. The amount of makeup water used to make styrene ranged from 2.19 to 123 gallons per pound; to make butadiene, ranged from 5.38 to 22.0 gallons per pound; and in the direct manufacture of SBR, ranged from 0.883 to 10.2 gallons per pound of finished rubber. The amount of makeup water withdrawn for use in the manufacture of special-purpose synthetic rubber ranged from 8.45 to 104 gallons per pound. About 64 percent of the makeup water was obtained from salty water sources. These waters, which were used only in once-through cooling, contained as much as 35,000 ppm of dissolved solids. About 26 percent of the makeup water was obtained from fresh-water streams and lakes, and most of the other makeup waters were obtained from ground water. Less than 1 percent of the makeup water was obtained from reprocessed municipal sewage. Most makeup water from fresh-water streams, lakes, and wells contained less than 1,000 ppm of dissolved solids, and most makeup water used in the manufacture of SBR contained less than 500 ppm of dissolved solids. The maximum hardness of the untreated fresh makeup waters; used in the manufacture of SBR was less than 500 ppm. About 97 percent of the makeup water withdrawn was discharged to surface waters; the warmed salty waters were returned to their source. The remaining 3 percent, or about 23.6 mgd, of makeup water was used consumptively. The styrene industry consumptively used about 2.0 percent of its intake; the butadiene industry, about 4.5 percent; the specialty-rubber industry, about 9.1 percent; and the SBR industry, about 11 percent. The water shipped in the synthetic-rubber products increased the consumptive use of water by these industries.

C-O volatiles in Apollo 15 and Apollo 17 picritic glasses

NASA Technical Reports Server (NTRS)

Rutherford, Malcolm J.; Fogel, Robert A.

1993-01-01

A15 and A17 primitive picritic glasses have been examined by FTIR for the presence of dissolved C-O species to determine the role of C-O gasses on driving lunar fire-fountains. A15 green and yellow glasses were extensively studied and found to be free of dissolved C species down to FTIR detection limits (10-100 ppm; species and sample specific). Preliminary data on A17 orange glasses are similarly devoid of FTIR detectable C-O species. Re-analyses of the C-O driving mechanism theory for mare volcanism demonstrates the need to determine the fO2 of the lunar interior; the factor that most critically determined the role of C gasses in the fire-fountaining events. Oxygen fugacities equivalent to IW-0.5 and above imply dissolved CO3(=) in the primitive glasses at levels above FTIR detection. The f02's below IW-0.5 imply concentrations of CO3(=) below FTIR detection. Recent data suggesting lunar mantle fO2's of IW-2 or less, strongly mitigate against finding FTIR measurable dissolved CO3(=) consistent with the findings of this study.

The impact of dissolved organic carbon and bacterial respiration on pCO2 in experimental sea ice

NASA Astrophysics Data System (ADS)

Zhou, J.; Kotovitch, M.; Kaartokallio, H.; Moreau, S.; Tison, J.-L.; Kattner, G.; Dieckmann, G.; Thomas, D. N.; Delille, B.

2016-02-01

Previous observations have shown that the partial pressure of carbon dioxide (pCO2) in sea ice brines is generally higher in Arctic sea ice compared to those from the Antarctic sea ice, especially in winter and early spring. We hypothesized that these differences result from the higher dissolved organic carbon (DOC) content in Arctic seawater: Higher concentrations of DOC in seawater would be reflected in a greater DOC incorporation into sea ice, enhancing bacterial respiration, which in turn would increase the pCO2 in the ice. To verify this hypothesis, we performed an experiment using two series of mesocosms: one was filled with seawater (SW) and the other one with seawater with an addition of filtered humic-rich river water (SWR). The addition of river water increased the DOC concentration of the water from a median of 142 μmol Lwater-1 in SW to 249 μmol Lwater-1 in SWR. Sea ice was grown in these mesocosms under the same physical conditions over 19 days. Microalgae and protists were absent, and only bacterial activity has been detected. We measured the DOC concentration, bacterial respiration, total alkalinity and pCO2 in sea ice and the underlying seawater, and we calculated the changes in dissolved inorganic carbon (DIC) in both media. We found that bacterial respiration in ice was higher in SWR: median bacterial respiration was 25 nmol C Lice-1 h-1 compared to 10 nmol C Lice-1 h-1 in SW. pCO2 in ice was also higher in SWR with a median of 430 ppm compared to 356 ppm in SW. However, the differences in pCO2 were larger within the ice interiors than at the surfaces or the bottom layers of the ice, where exchanges at the air-ice and ice-water interfaces might have reduced the differences. In addition, we used a model to simulate the differences of pCO2 and DIC based on bacterial respiration. The model simulations support the experimental findings and further suggest that bacterial growth efficiency in the ice might approach 0.15 and 0.2. It is thus credible that the higher pCO2 in Arctic sea ice brines compared with those from the Antarctic sea ice were due to an elevated bacterial respiration, sustained by higher riverine DOC loads. These conclusions should hold for locations and time frames when bacterial activity is relatively dominant compared to algal activity, considering our experimental conditions.

21 CFR 556.300 - Gentamicin sulfate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... million in fat and kidney. A microbiological determinative procedure and an HPLC confirmatory procedure for gentamicin have been developed to assay gentamicin in kidney at 0.4 ppm. Since residues of... concentration of 0.4 ppm in kidney corresponds to 0.4 ppm of total residue. [48 FR 791, Jan. 7, 1983, as amended...

21 CFR 556.300 - Gentamicin sulfate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... million in fat and kidney. A microbiological determinative procedure and an HPLC confirmatory procedure for gentamicin have been developed to assay gentamicin in kidney at 0.4 ppm. Since residues of... concentration of 0.4 ppm in kidney corresponds to 0.4 ppm of total residue. [48 FR 791, Jan. 7, 1983, as amended...

The Effects of Boron Doping on Residual Stress of Hfcvd Diamond Film for Mems Applications

NASA Astrophysics Data System (ADS)

Zhao, Tianqi; Wang, Xinchang; Sun, Fanghong

In this study, the residual stress of boron-doped diamond (BDD) films is investigated as a function of boron doping level using X-ray diffraction (XRD) analysis. Boron doping level is controlled from 1000ppm to 9000ppm by dissolving trimethyl borate into acetone. BDD films are deposited on silicon wafers using a bias-enhanced hot filament chemical vapor deposition (BE-HFCVD) system. Residual stress calculated by sin2 ψ method varies linearly from -2.4GPa to -1.1GPa with increasing boron doping level. On the BDD film of -1.75GPa, free standing BDD cantilevers are fabricated by photolithography and ICP-RIE processes, then tested by laser Doppler vibrometer (LDV). A cantilever with resonant frequency of 183KHz and Q factor of 261 in the air is fabricated.

[Characteristics of nitrogen and phosphorus runoff losses from croplands with different planting patterns in a riverine plain area of Zhejiang Province, East China].

PubMed

Zhang, Ming-Kui; Wang, Yang; Huang, Chao

2011-12-01

By the method of site-specific observation, and selecting 27 field plots with 7 planting patterns in Shaoxing county of Zhejiang Province as test objects, this paper studied the characteristics of nitrogen (N) and phosphorous (P) runoff losses, loads, and their affecting factors in the croplands with different planting patterns in riverine plain area of the Province under natural rainfall. The mean annual runoff loads of total P, dissolved P, and particulate P from the field plots were 4.75, 0.74 and 4.01 kg x hm(-2), respectively, and the load of particulate P was much higher than that of dissolved P. The mean annual runoff loads of total N, dissolved total N, dissolved organic N, NH4(+)-N, and NO3(-)-N were 21.87, 17.19, 0.61, 3.63 and 12.95 kg x hm(-2), respectively, and the load of different fractions of dissolved total N was in the sequence of NO3(-)-N > NH4(+)-N > dissolved organic N. As for the field plots with different planting patterns, the runoff loads of total N, dissolved total N, dissolved organic N, and NO3(-)-N were in the sequence of fallow land < nursery land < single late rice field < double rice field < rape (or wheat)-single late rice field < wheat-early rice-late rice field < vegetable field, while those of total P and particulate P were in the sequence of fallow land < nursery land < single late rice field and double rice field < wheat-early rice-late rice field < rape (wheat)-single late rice field < vegetable field. No significant difference was observed in the load of water-dissolved P among the test plots with different planting patterns. The runoff losses of N and P mainly occurred in crop growth period, and the proportions of N and P losses in the growth period increased with increasing multiple crop index. The runoff losses of total N, dissolved N, and NO3(-)-N were mainly related to the application rate of N fertilizer, and soil NO3(-)-N content also had obvious effects on the runoff losses of total N and dissolved N. The runoff loss of dissolved organic N was related not only to N application rate, but also to soil total N and organic carbon. The runoff loss of NH4(+)-N was mainly related to soil available NH4(+)-N, but not related to N application rate. The runoff losses of total P and particulate P were related to both P application rate and soil available P, while the runoff loss of water dissolved P was less related to P application rate but had relations to soil total P and available P.

Characterization of urban runoff pollution between dissolved and particulate phases.

PubMed

Wei, Zhang; Simin, Li; Fengbing, Tang

2013-01-01

To develop urban stormwater management effectively, characterization of urban runoff pollution between dissolved and particulate phases was studied by 12 rainfall events monitored for five typical urban catchments. The average event mean concentration (AEMC) of runoff pollutants in different phases was evaluated. The AEMC values of runoff pollutants in different phases from urban roads were higher than the ones from urban roofs. The proportions of total dissolved solids, total dissolved nitrogen, and total dissolved phosphorus in total ones for all the catchments were 26.19%-30.91%, 83.29%-90.51%, and 61.54-68.09%, respectively. During rainfall events, the pollutant concentration at the initial stage of rainfall was high and then sharply decreased to a low value. Affected by catchments characterization and rainfall distribution, the highest concentration of road pollutants might appear in the later period of rainfall. Strong correlations were also found among runoffs pollutants in different phases. Total suspended solid could be considered as a surrogate for particulate matters in both road and roof runoff, while dissolved chemical oxygen demand could be regarded as a surrogate for dissolved matters in roof runoff.

Hydrogeology and structure of the Bluewater Springs area south central Montana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Padilla, C.E.; Osborne, T.J.

1996-06-01

The Bluewater springs area in south central Montana was the site of oil and gas exploration in the first half of this century. Though no significant oil was found, artesian water wells produced over 3,000 gallons per minute. Artesian springs in the area produce tufa deposits over faulted, northwest dipping Mesozoic and upper Paleozoic sediments. Two new faults were mapped in the vicinity, one of these a high angle vertical fault dissects an anticline. The Tensleep and Madison aquifers (700-1,000 feet deep) leak water to the surface through faults and fractures, producing variable water quality depending on the minerals dissolvedmore » from overlying rock formations. Evaluation of limited aquifer data reveals the following: (1) hydraulic conductivity of 40,000 to 300,000 gpd/ft, (2) hydrostatic head greater than 400 feet above land surface. (3) Total dissolved solids concentrations were 2,370 ppm in Big Bluewater Springs, but only 1,200 ppm in a Tensleep well in the vicinity. Flowing wells 45 to 70 years old have failed leading to major yield reductions, and cessation of flow. Potentially corrosive groundwater coupled with excessive flow velocities and inadequate well construction has likely led to well failures. In response, major uncontrolled alterations of groundwater flow systems have occurred with outbreaks of new springs and sinkholes near failed wells. New wells must be carefully planned, constructed and tested to avoid excessive interference, depressurization and failure.« less

Reverse osmosis plant maintenance and efficacy in chronic kidney disease endemic region in Sri Lanka.

PubMed

Jayasumana, Channa; Ranasinghe, Omesh; Ranasinghe, Sachini; Siriwardhana, Imalka; Gunatilake, Sarath; Siribaddana, Sisira

2016-11-01

Chronic Interstitial Nephritis in Agricultural Communities (CINAC) causes major morbidity and mortality for farmers in North-Central province (NCP) of Sri Lanka. To prevent the CINAC, reverse osmosis (RO) plants are established to purify the water and reduce the exposure to possible nephrotoxins through drinking water. We assessed RO plant maintenance and efficacy in NCP. We have interviewed 10 RO plant operators on plant establishment, maintenance, usage and funding. We also measured total dissolved solids (TDS in ppm) to assess the efficacy of the RO process. Most RO plants were operated by community-based organizations. They provide clean and sustainable water source for many in the NCP for a nominal fee, which tends to be variable. The RO plant operators carry out RO plant maintenance. However, maintenance procedures and quality management practices tend to vary from an operator to another. RO process itself has the ability to lower the TDS of the water. On average, RO process reduces the TDS to 29 ppm. The RO process reduces the impurities in water available to many individuals within CINAC endemic regions. However, there variation in maintenance, quality management, and day-to-day care between operators can be a cause for concern. This variability can affect the quality of water produced by RO plant, its maintenance cost and lifespan. Thus, uniform regulation and training is needed to reduce cost of maintenance and increase the efficacy of RO plants.

Popping Rocks Revealed: Investigations from 14°N on the Mid-Atlantic Ridge

NASA Astrophysics Data System (ADS)

Wanless, V. D.; Jones, M.; Kurz, M. D.; Soule, S. A.; Fornari, D. J.; Bendana, S.; Mittelstaedt, E. L.

2017-12-01

The popping rock, recovered in dredge 2πD43 in 1985, is commonly considered to be one of the most representative samples of undegassed upper mantle, based on high volatile and noble gas abundances. While this basalt is used to reconstruct mantle volatile contents and CO2 fluxes from mid-ocean ridges (MOR), the origin of the popping rock has remained ambiguous due to a lack of geologic context. Here, we present results from the first combined geochemical, geophysical, and geologic investigation of popping rocks from 14N on the Mid-Atlantic Ridge. By combining lava compositions with high-resolution bathymetric maps, we show that the popping rocks are confined to a single geographic area, at the transition between magmatic and tectonic segments. Fifteen popping rocks were collected in situ using the Alvin submersible in 2016. X-ray microtomography indicates that these lavas have variable vesicle abundances; including the highest vesicularities (>19%) recorded for any MOR basalt. Dissolved CO2 contents (163-175 ppm) are similar to proximal non-popping rocks and are in equilibrium at their eruption depths (>3600 m); however, total CO2 contents (based on vesicularity, dissolved CO2, and vesicle gas contents) are higher than non-popping rocks, ranging from 2800-14150 ppm. The popping rocks have average 3He/4He ratios of 8.17 ± 0.1 Ra and 4He concentrations of 1.84e-5 to 7.67e-5 cc/g STP. Compared to non-popping lavas, the popping rocks have a narrow range of major and trace element concentrations, suggesting little to no crystallization occurred during ascent or eruption. REE patterns and trace element ratios are indistinguishable in the popping rocks (La/Sm = 2.89 ± 0.05), indicating similar mantle sources and extents of melting. Based on lava compositions and spatial distribution, we suggest that the popping rocks at 14N were produced under similar magmatic conditions and erupted over short timescales, perhaps during a series of closely timed eruptions.

Methodology Measuring Rare Earth Elements in High TDS Reservoir Brines Application as Natural Tracers in CCUS Studies

NASA Astrophysics Data System (ADS)

Smith, W.; Mcling, T. L.; Smith, R. W.; Neupane, H.

2013-12-01

In recent years rare earth elements (REE) have been demonstrated to be useful natural tracers for geochemical processes in aqueous environments. The application of REE's to carbon dioxide utilization and storage (CCUS) could provide researchers with a sensitive, inexpensive tool for tracking the movement of CO2 and displaced formation brines. By definition, geologic reservoirs that have been deemed suitable for carbon capture and storage contain formation brine with total dissolved solids (TDS) greater than 10,000 ppm and often these formation brines exceed 75,000 ppm TDS. This high TDS water makes it very difficult to measure REE, which typically occur at part per trillion concentrations. Critical to the use of REE for CCUS studies is the development of a procedure, which allows for the pre-concentration of REE's across a wide range of water quality. Additionally, due to the large number of samples that will need analysis, any developed procedure must be inexpensive, reproducible, and quick to implement. As part of the Big Sky Carbon Sequestration Project the INL's Center for Advance Energy Studies is developing REE pre-concentration procedures based on methods reported in the literature. While there are many REE pre-concentration procedures in the literature, our tests have shown these methods have difficulty at TDS greater than seawater (roughly 35,000 ppm TDS). Therefore, the ability to quantitatively measure REE's in formation brines with very high TDS has required the modification of an already developed procedure. After careful consideration and testing we selected methods modified after those described by Kingston et al., 1978 and Strachan et al., 1989 utilizing chelating media for very high TDS waters and ion-exchange media as detailed by Crock et al., 1984; Robinson et al., 1985; and Stetzenbach et al., 1994 for low TDS (<10,000 ppm TDS) waters. These modified procedures have been successfully tested in our laboratory and have proven effective in greatly reducing interfering monovalent and divalent cation concentrations (e.g. Ba) and enriching the REE up to 100X for analysis. The procedures are straightforward, inexpensive, and require little infrastructure, using only single chromatography columns with inexpensive, reusable, commercially available resins and wash chemicals. The procedures have been tested with synthetic brines and waters (up to 250,000 ppm TDS) and field water samples (up to 5,000 ppm TDS). Testing has produced data with REE capture efficiency exceeding 95%, while reducing interfering elements by more than 93%. Further method development and testing continues in preparation for brine analysis of waters from the Big Sky Carbon Sequestration Partnership's Kevin Dome Pilot Study and the University of Wyoming's Carbon Institutes Rock Springs Uplift.

21 CFR 74.2053 - D&C Black No. 3.

Code of Federal Regulations, 2011 CFR

2011-04-01

... may be avoided by current good manufacturing practices: (1) Calcium hydroxyapatite (CaO and P2O5), not... milligrams (mg)/kilogram (kg) (3 parts per million (ppm)); (6) Lead, not more than 10 mg/kg (10 ppm); and (7) Total polycyclic aromatic hydrocarbons (PAHs), not more than 5 mg/kg (5 ppm). (c) Uses and restrictions...

21 CFR 74.2053 - D&C Black No. 3.

Code of Federal Regulations, 2014 CFR

2014-04-01

... may be avoided by current good manufacturing practices: (1) Calcium hydroxyapatite (CaO and P2O5), not... milligrams (mg)/kilogram (kg) (3 parts per million (ppm)); (6) Lead, not more than 10 mg/kg (10 ppm); and (7) Total polycyclic aromatic hydrocarbons (PAHs), not more than 5 mg/kg (5 ppm). (c) Uses and restrictions...

21 CFR 74.2053 - D&C Black No. 3.

Code of Federal Regulations, 2013 CFR

2013-04-01

... may be avoided by current good manufacturing practices: (1) Calcium hydroxyapatite (CaO and P2O5), not... milligrams (mg)/kilogram (kg) (3 parts per million (ppm)); (6) Lead, not more than 10 mg/kg (10 ppm); and (7) Total polycyclic aromatic hydrocarbons (PAHs), not more than 5 mg/kg (5 ppm). (c) Uses and restrictions...

21 CFR 74.2053 - D&C Black No. 3.

Code of Federal Regulations, 2012 CFR

2012-04-01

... may be avoided by current good manufacturing practices: (1) Calcium hydroxyapatite (CaO and P2O5), not... milligrams (mg)/kilogram (kg) (3 parts per million (ppm)); (6) Lead, not more than 10 mg/kg (10 ppm); and (7) Total polycyclic aromatic hydrocarbons (PAHs), not more than 5 mg/kg (5 ppm). (c) Uses and restrictions...

Thermodynamics of dissolved nitrogen, nitrous oxide, and ammonia in perfluorodecalin

NASA Astrophysics Data System (ADS)

Moshnyaga, A. V.; Khoroshilov, A. V.; Selivanova, D. I.; Aksenova, D. M.

2017-11-01

The solubility of N2, N2O, and NH3 is studied in different organic solvents. The best dissolution (0.27 ppm) is found to be for N2O in perfluorodecalin at 291 K and a pressure of 99 kPa. The dependence of N2O solubility in perfluorodecalin on pressure is studied at 291 K. The Gibbs energy of the solubility of nitrogen, nitrous oxide, and ammonia in perfluorodecalin is calculated.

Laboratory measurements of physical, chemical, and optical characteristics of Lake Chicot sediment waters

NASA Technical Reports Server (NTRS)

Witte, W. G.; Whitlock, C. H.; Usry, J. W.; Morris, W. D.; Gurganus, E. A.

1981-01-01

Reflectance, chromaticity, diffuse attenuation, beam attenuation, and several other physical and chemical properties were measured for various water mixtures of lake bottom sediment. Mixture concentrations range from 5 ppm to 700 ppm by weight of total suspended solids in filtered deionized tap water. Upwelled reflectance is a nonlinear function of remote sensing wave lengths. Near-infrared wavelengths are useful for monitoring highly turbid waters with sediment concentrations above 100 ppm. It is found that both visible and near infrared wavelengths, beam attenuation correlates well with total suspended solids ranging over two orders of magnitude.

Microwave assisted synthesis, characterization and biocidal activities of some new chelates of carbazole derived Schiff bases of cadmium and tin metals.

PubMed

Yadav, Manju; Mishra, Neelima; Sharma, Nutan; Chandra, Sulekh; Kumar, Dinesh

2014-11-11

This study is planned to report the advancement of green microwave approach in the fabrication of a new series of biologically potent (N^X, where X=O/S) donor Schiff bases and their cadmium(II) and tin(II) complexes. The ligands and their metal complexes have been characterized in terms of elemental analysis, molar ionic conductance, magnetic moment and spectral (IR, UV-Vis, NMR ((1)H, (119)Sn), FAB-mass, thermal and XRD) data. The data revealed that the ligands coordinated to the metal center via nitrogen and oxygen/sulfur atoms and form an octahedral arrangement of the ligands around central metal atom. All compounds were evaluated for their in vitro antimicrobial activities against two pathogenic bacteria Bacillus subtilis and Escherichia coli and two fungi Aspergillus niger and Aspergillus flavus by standard disc diffusion method. The discs were stored in an incubator at 37°C. The compounds were dissolved in DMF at 500 and 1000 ppm concentrations for screening biocidal activity. The compounds were dissolved in DMF to get the 100 and 200 ppm concentration of test solutions for screening fungicidal activity. The inhibition zone around each disc was measured (in mm) after 24 h and 96 h for biocidal and fungicidal activities respectively. Copyright © 2014 Elsevier B.V. All rights reserved.

Uranium delivery and uptake in a montane wetland, north-central Colorado, USA

USGS Publications Warehouse

Schumann, R. Randall; Zielinski, Robert A.; Otton, James K.; Pantea, Michael P.; Orem, William H.

2017-01-01

Comprehensive sampling of peat, underlying lakebed sediments, and coexisting waters of a naturally uraniferous montane wetland are combined with hydrologic measurements to define the important controls on uranium (U) supply and uptake. The major source of U to the wetland is groundwater flowing through locally fractured and faulted granite gneiss of Proterozoic age. Dissolved U concentrations in four springs and one seep ranged from 20 to 83 ppb (μg/l). Maximum U concentrations are ∼300 ppm (mg/kg) in lakebed sediments and >3000 ppm in peat. Uranium in lakebed sediments is primarily stratabound in the more organic-rich layers, but samples of similar organic content display variable U concentrations. Post-depositional modifications include variable additions of U delivered by groundwater. Uranium distribution in peat is heterogeneous and primarily controlled by proximity to groundwater-fed springs and seeps that act as local point sources of U, and by proximity to groundwater directed along the peat/lakebeds contact. Uranium is initially sorbed on various organic components of peat as oxidized U(VI) present in groundwater. Selective extractions indicate that the majority of sorbed U remains as the oxidized species despite reducing conditions that should favor formation of U(IV). Possible explanations are kinetic hindrances related to strong complex formation between uranyl and humic substances, inhibition of anaerobic bacterial activity by low supply of dissolved iron and sulfate, and by cold temperatures.

New Mechanisms of Mercury Binding to Peat

NASA Astrophysics Data System (ADS)

Nagy, K. L.; Manceau, A.; Gasper, J. D.; Ryan, J. N.; Aiken, G. R.

2007-12-01

Mercury can be immobilized in the aquatic environment by binding to peat, a solid form of natural organic matter. Binding mechanisms can vary in strength and reversibility, and therefore will control concentrations of bioreactive mercury, may explain rates of mercury methylation, and are important for designing approaches to improve water quality using natural wetlands or engineered phytoremediation schemes. In addition, strong binding between mercury and peat is likely to result in the fixation of mercury that ultimately resides in coal. The mechanisms by which aqueous mercury at low concentrations reacts with both dissolved and solid natural organic matter remain incompletely understood, despite recent efforts. We have identified three distinct binding mechanisms of divalent cationic mercury to solid peats from the Florida Everglades using EXAFS spectroscopic data (FAME beamline, European Synchrotron Radiation Facility (ESRF)) obtained on experimental samples as compared to relevant references including mercury-bearing solids and mercury bound to various organic molecules. The proportions of the three molecular configurations vary with Hg concentration, and two new configurations that involve sulfur ligands occur at Hg concentrations up to about 4000 ppm. The binding mechanism at the lowest experimental Hg concentration (60-80 ppm) elucidates published reports on the inhibition of metacinnabar formation in the presence of Hg-bearing solutions and dissolved natural organic matter, and also, the differences in extent of mercury methylation in distinct areas of the Florida Everglades.

H 2OCH 4NaClCO 2 inclusions from the footwall contact of the Tanco granitic pegmatite: Estimates of internal pressure and composition from microthermometry, laser Raman spectroscopy, and gas chromatography

NASA Astrophysics Data System (ADS)

Thomas, A. V.; Pasteris, J. D.; Bray, C. J.; Spooner, E. T. C.

1990-03-01

Fluid inclusions in tourmaline and quartz from the footwall contact of the Tanco granitic pegmatite, S.E. Manitoba were studied using microthermometry (MT), laser Raman spectroscopy (LRS) and gas chromatography (GC). CH 4-bearing, aqueous inclusions occur in metasomatic tourmaline of the footwall amphibolite contact. The internal pressures estimated from MT are lower than those obtained from LRS (mean difference = 54 ± 19 bars). The difference is probably due to errors in the measurement of Th CH 4 (V) and to the presence of clathrate at Th CH 4 (V) into which CO 2 had been preferentially partitioned. LRS estimates of pressure (125-184 bars) are believed to be more accurate. Aqueous phase salinities based on LRS estimates of pressure are higher than those derived using the data from MT: 10-20 eq. wt% NaCl. The composition of the inclusions determined by GC bulk analysis is 97.3 mol% H 2O, 2.2 mol% CH 4, 0.4 mol% CO 2, 250 ppm C 2H 6, 130 ppm N 2, 33 ppm C 3H 8, 11 ppm C 2H 4, and 3 ppm C 3H 6, plus trace amounts of C 4 hydrocarbons. The composition is broadly similar to that calculated from MT (92% H 2O and 8% CH 4, with 7 eq. wt% NaCl dissolved in the aqueous phase and 2 mol% CO 2 dissolved in the CH 4 phase), as expected due to the dominance of a single generation of inclusions in the tourmaline. However, two important differences in composition are: (i) the CH 4 to CO 2 ratio of this fluid determined by GC is 5.33, which is significantly lower than that indicated by MT (49.0); and (ii) the H 2O content estimated from MT is 92 mol% compared to 98 mol% from GC. GC analyses may have been contaminated by the presence of secondary inclusions in the tourmaline. However, the rarity of the latter suggests that they cannot be completely responsible for the discrepancy. The differences may be accounted for by the presence of clathrate during measurement of Th CH 4 (critical), which would reduce CO 2 relative to CH 4 in the residual fluid, and by errors in visually estimating vol% H 2O. The compositions of the primary inclusions in tourmaline are unlike any of those found within the pegmatite and indicate that the fluid was externally derived, probably of metamorphic origin. Inclusions in quartz of the border unit of the pegmatite are secondary and are either aqueous (18 to 30 eq. wt% CaCl 2; Th total = 184 ± 14° C) or carbonic. Tm CO 2 for the carbonic inclusions ranges from -57.5 to -65.4°C and is positively correlated with Th CO 2. Analyses of X CH 4 based on LRS agree within 5 mol% of those derived from MT and together indicate a range of compositions from 5 to 50 mol% CH 4 in the CO 2 phase. Bulk analysis by GC gives 99.0 mol% H 2O, 0.6 mol% CO 2, 0.4 mol% CH 4, 160 ppm N 2, 7 ppm C 2H 6, 4 ppm C 3H 8, and 2 ppm C 2H 4, with trace amounts of COS (carbonyl sulphide) and C 3H 6. The level of H 2O in the analysis is consistent with the dominance of the aqueous inclusions in these samples, and the CH4: CO2 ratios are consistent with estimates from MT and LRS. The preservation of variable ratios of CH 4:CO 2 in inclusions < 50 μm apart indicates that neither H 2 diffusion out of the inclusions nor reduction of fluids leaving the pegmatite were responsible for the more oxidized chemistries of the border unit inclusions relative to those in the tourmaline of the metasomatised amphibolite. The compositions of the inclusions in the quartz lie between those of the fluid trapped by the tourmaline (externally derived) and the measured composition of a CO 2-bearing pegmatitic fluid, which indicates that the secondary fluids trapped in the border unit quartz were produced by late mixing.

Trends in nitrate and dissolved-solids concentrations in ground water, Carson Valley, Douglas County, Nevada, 1985-2001

USGS Publications Warehouse

Rosen, Michael R.

2003-01-01

Analysis of trends in nitrate and total dissolved-solids concentrations over time in Carson Valley, Nevada, indicates that 56 percent of 27 monitoring wells that have long-term records of nitrate concentrations show increasing trends, 11 percent show decreasing trends, and 33 percent have not changed. Total dissolved-solids concentrations have increased in 52 percent of these wells and are stable in 48 percent. None of these wells show decreasing trends in total dissolved-solids concentrations. The wells showing increasing trends in nitrate and total dissolved-solids concentrations were always in areas that use septic waste-disposal systems. Therefore, the primary cause of these increases is likely the increase in septic-tank usage over the past 40 years.

Water quality of Lake Whitney, north-central Texas

USGS Publications Warehouse

Strause, Jeffrey L.; Andrews, Freeman L.

1983-01-01

Seasonal temperature variations and variations in the concentration of dissolved oxygen result in dissolved iron, dissolved manganese, total inorganic nitrogen, and total phosphorus being recycled within the lake; however, no significant accumulations of these constituents were detected.

Characterization of Urban Runoff Pollution between Dissolved and Particulate Phases

PubMed Central

Wei, Zhang; Simin, Li; Fengbing, Tang

2013-01-01

To develop urban stormwater management effectively, characterization of urban runoff pollution between dissolved and particulate phases was studied by 12 rainfall events monitored for five typical urban catchments. The average event mean concentration (AEMC) of runoff pollutants in different phases was evaluated. The AEMC values of runoff pollutants in different phases from urban roads were higher than the ones from urban roofs. The proportions of total dissolved solids, total dissolved nitrogen, and total dissolved phosphorus in total ones for all the catchments were 26.19%–30.91%, 83.29%–90.51%, and 61.54–68.09%, respectively. During rainfall events, the pollutant concentration at the initial stage of rainfall was high and then sharply decreased to a low value. Affected by catchments characterization and rainfall distribution, the highest concentration of road pollutants might appear in the later period of rainfall. Strong correlations were also found among runoffs pollutants in different phases. Total suspended solid could be considered as a surrogate for particulate matters in both road and roof runoff, while dissolved chemical oxygen demand could be regarded as a surrogate for dissolved matters in roof runoff. PMID:23935444

Effects of temperature, total dissolved solids, and total suspended solids on survival and development rate of larval Arkansas River Shiner

USGS Publications Warehouse

Mueller, Julia S.; Grabowski, Timothy B.; Brewer, Shannon K.; Worthington, Thomas A.

2017-01-01

Decreases in the abundance and diversity of stream fishes in the North American Great Plains have been attributed to habitat fragmentation, altered hydrological and temperature regimes, and elevated levels of total dissolved solids and total suspended solids. Pelagic-broadcast spawning cyprinids, such as the Arkansas River Shiner Notropis girardi, may be particularly vulnerable to these changing conditions because of their reproductive strategy. Our objectives were to assess the effects of temperature, total dissolved solids, and total suspended solids on the developmental and survival rates of Arkansas River Shiner larvae. Results suggest temperature had the greatest influence on the developmental rate of Arkansas River Shiner larvae. However, embryos exposed to the higher levels of total dissolved solids and total suspended solids reached developmental stages earlier than counterparts at equivalent temperatures. Although this rapid development may be beneficial in fragmented waters, our data suggest it may be associated with lower survival rates. Furthermore, those embryos incubating at high temperatures, or in high levels of total dissolved solids and total suspended solids resulted in less viable embryos and larvae than those incubating in all other temperature, total dissolved solid, and total suspended solid treatment groups. As the Great Plains ecoregion continues to change, these results may assist in understanding reasons for past extirpations and future extirpation threats as well as predict stream reaches capable of sustaining Arkansas River Shiners and other species with similar early life-history strategies.

Studies on physico-chemical changes during artificial ripening of banana (Musa sp) variety 'Robusta'.

PubMed

Kulkarni, Shyamrao Gururao; Kudachikar, V B; Keshava Prakash, M N

2011-12-01

Banana (Musa sp var 'Robusta') fruits harvested at 75-80% maturity were dip treated with different concentrations of ethrel (250-1,000 ppm) solution for 5 min. Ethrel at 500 ppm induced uniform ripening without impairing taste and flavour of banana. Untreated control banana fruits remained shriveled, green and failed to ripen evenly even after 8 days of storage. Fruits treated with 500 ppm of ethrel ripened well in 6 days at 20 ± 1 °C. Changes in total soluble solids, acidity, total sugars and total carotenoids showed increasing trends up to 6 days during ripening whereas fruit shear force values, pulp pH and total chlorophyll in peel showed decreasing trends. Sensory quality of ethrel treated banana fruits (fully ripe) were excellent with respect to external colour, taste, flavour and overall quality.

Fetal and Neonatal Iron Deficiency Exacerbates Mild Thyroid Hormone Insufficiency Effects on Male Thyroid Hormone Levels and Brain Thyroid Hormone-Responsive Gene Expression

PubMed Central

Bastian, Thomas W.; Prohaska, Joseph R.; Georgieff, Michael K.

2014-01-01

Fetal/neonatal iron (Fe) and iodine/TH deficiencies lead to similar brain developmental abnormalities and often coexist in developing countries. We recently demonstrated that fetal/neonatal Fe deficiency results in a mild neonatal thyroidal impairment, suggesting that TH insufficiency contributes to the neurodevelopmental abnormalities associated with Fe deficiency. We hypothesized that combining Fe deficiency with an additional mild thyroidal perturbation (6-propyl-2-thiouracil [PTU]) during development would more severely impair neonatal thyroidal status and brain TH-responsive gene expression than either deficiency alone. Early gestation pregnant rats were assigned to 7 different treatment groups: control, Fe deficient (FeD), mild TH deficient (1 ppm PTU), moderate TH deficient (3 ppm PTU), severe TH deficient (10 ppm PTU), FeD/1 ppm PTU, or FeD/3 ppm PTU. FeD or 1 ppm PTU treatment alone reduced postnatal day 15 serum total T4 concentrations by 64% and 74%, respectively, without significantly altering serum total T3 concentrations. Neither treatment alone significantly altered postnatal day 16 cortical or hippocampal T3 concentrations. FeD combined with 1 ppm PTU treatment produced a more severe effect, reducing serum total T4 by 95%, and lowering hippocampal and cortical T3 concentrations by 24% and 31%, respectively. Combined FeD/PTU had a more severe effect on brain TH-responsive gene expression than either treatment alone, significantly altering Pvalb, Dio2, Mbp, and Hairless hippocampal and/or cortical mRNA levels. FeD/PTU treatment more severely impacted cortical and hippocampal parvalbumin protein expression compared with either individual treatment. These data suggest that combining 2 mild thyroidal insults during development significantly disrupts thyroid function and impairs TH-regulated brain gene expression. PMID:24424046

Ultra-high chlorine in submarine Kı̄lauea glasses: Evidence for direct assimilation of brine by magma

USGS Publications Warehouse

Coombs, Michelle L.; Sisson, Thomas W.; Kimura, Jun-Ichi

2004-01-01

Basaltic glass grains from the submarine south flank of Kı̄lauea, Hawai′i, have Cl concentrations of 0.01–1.68 wt%, the latter being the highest Cl content yet recorded for a Hawaiian glass. The high-Cl glass grains are products of brine assimilation by tholeiite magma. The glasses are grains in a sandstone clast from bedded breccias draping the southwestern margin of Kı̄lauea’s submarine midslope bench. The clast contains two distinct suites of glass grains: abundant degassed tholeiites, perhaps derived from subaerial lavas of Mauna Loa that shattered upon ocean entry, and a smaller population of Kea-type tholeiite (n=17 analyzed) that erupted subaqueously, based on elevated S (780–1050 ppm), H2O (0.42–1.27 wt%), and CO2 (<30–120 ppm), probably early in Kı̄lauea’s shield-building stage. Ten grains in this group have Cl>1000 ppm, six >5000 ppm, and two grains have >10 000 ppm dissolved Cl. Abundances of H2O, Na2O, K2O, and several trace elements increase regularly with Cl concentration, and we estimate that Cl enrichment was due to up to 13 wt% addition of a brine consisting of 78% H2O (wt), 13% Cl, 4.4% Na, 2.6% K, 2.6% Ca, 620 ppm Ba, 360 ppm Sr, 65 ppm Rb, and 7 ppm Pb. The large amounts of brine addition argue against bulk assimilation of low-porosity brine-bearing rock. The brine’s composition is appropriate for a seawater-derived hydrothermal fluid that reacted with basaltic wall rocks at T>100°C, losing Mg and S and gaining K, Ca, Rb, Ba, Sr, and Pb, followed by phase separation near 500°C and ∼50 MPa (5 km below sea level at hydrostatic pressure). Brine was assimilated at or near the depth it formed, as estimated on petrologic grounds, but under lithostatic conditions. The highest extents of assimilation either forced volatile saturation of the magma or enriched already coexisting magmatic vapor in H2O. Possible mechanisms for assimilation are: (1) forcible injection of brine into magma during bursting of overpressured pockets heated by new dikes, or (2) intrusion of magma into lenses or sills occupied by trapped brine.

Short-tailed shrews: Toxicity and residue relationships of DDT, dieldrin, and endrin

USGS Publications Warehouse

Blus, L.J.

1978-01-01

Experiments involving dietary toxicity and residue relationships of DDT, dieldrin, and endrin were conducted with short-tailed shrews. Dietary concentrations of DDT dissolved in vegetable oils were usually more toxic than diets containing comparable amounts of powdered DDT. Younger shrews, particularly females, were more tolerant of powdered DDT than older animals; yet, there were no conspicuous age differences in toxicity of DDT dissolved in oils. In comparison to other mammals, short-tailed shrews are not unusually sensitive to DDT, dieldrin, or endrin on the basis of two-week feeding tests. The influence of age and sex on toxicity of DDT, endrin, and dieldrin was sometimes more important than body weight. Of those shrews of the same age and sex that were fed the same dietary dosage, heavier shrews were more tolerant than lighter individuals; and, heavier shrews tended to lose a greater percentage of body weight before death. There was a range of 15 to 105 DDT equivalents in brains of shrews dying on dietary dosages of DDT. Six shrews fed a high level of DDT seemed to have unusual metabolite capabilities and died with apparent lethal levels of DDD in their brains. Levels of dieldrin in brains of shrews that died on a dietary dosage of dieldrin ranged from 3.7 to 12.6 ppm. In the rates of gain and loss experiments where shrews were given diets containing 400 ppm DDT or 50 ppm dieldrin up to 17 days, high residues were noted in tissues of shrews after two weeks on a contaminated diet and a few died at that time. After shrews were placed on clean food, it was determined that >50% of the dieldrin residues in carcass and brain were lost in 50% of residues of DDT and metabolites in brains after 2 weeks on clean food; males lost nearly 50% of residues in carcasses after two weeks on clean food compared with a loss of only 11% in females.

Effect of pulsed corona discharge voltage and feed gas flow rate on dissolved ozone concentration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prasetyaningrum, A., E-mail: ajiprasetyaningrum@gmail.com; Ratnawati,; Jos, B.

Ozonization is one of the methods extensively used for water purification and degradation of organic materials. Ozone (O{sub 3}) is recognized as a powerful oxidizing agent. Due to its strong oxidability and better environmental friendless, ozone increasing being used in domestic and industrial applications. Current technology in ozone production utilizes several techniques (corona discharge, ultra violet radiation and electrolysis). This experiment aimed to evaluating effect of voltage and gas flow rate on ozone production with corona discharge. The system consists of two net-type stainless steel electrode placed in a dielectric barrier. Three pulsed voltage (20, 30, 40 KV) and flowmore » rate (5, 10, 15 L/min) were prepare for operation variable at high frequency (3.7 kHz) with AC pulsed power supply. The dissolved ozone concentration depends on the applied high-voltage level, gas flow rate and the discharge exposure duration. The ozone concentration increases with decreasing gas flow rate. Dissolved ozone concentrations greater than 200 ppm can be obtained with a minimum voltage 40 kV.« less

Influence of dissolved gases and heat treatments on the oxidative degradation of polyunsaturated fatty acids enriched dairy beverage.

PubMed

Giroux, Hélène J; Acteau, Geneviève; Sabik, Hassan; Britten, Michel

2008-07-23

The combined effect of dissolved gas composition and heat treatment on the oxidative degradation of a dairy beverage enriched with 2% linseed oil was studied. The dairy beverage was saturated with air, nitrogen, or a nitrogen/hydrogen mixture (4% hydrogen) before pasteurization or sterilization. Saturation with either nitrogen or a nitrogen/hydrogen mixture decreased the dissolved oxygen concentration in dairy beverages (Delta = 7.7 ppm), and the presence of hydrogen significantly reduced the redox potential (Delta = 287 mV). Heat treatments also reduced the oxygen content and redox potential, sterilization being more effective than pasteurization. Both pasteurization and sterilization induced the oxidative degradation of the beverages. On average, the propanal concentration increased by a factor of 2.3 after pasteurization and by a factor of 6.2 after sterilization. However, during storage, sterilized beverages resisted light-induced oxidation better than unheated or pasteurized beverages. Furthermore, saturation with nitrogen or a nitrogen/hydrogen mixture significantly reduced oxidative degradation and provided some protection against color changes during storage.

Effect of pulsed corona discharge voltage and feed gas flow rate on dissolved ozone concentration

NASA Astrophysics Data System (ADS)

Prasetyaningrum, A.; Ratnawati, Jos, B.

2015-12-01

Ozonization is one of the methods extensively used for water purification and degradation of organic materials. Ozone (O3) is recognized as a powerful oxidizing agent. Due to its strong oxidability and better environmental friendless, ozone increasing being used in domestic and industrial applications. Current technology in ozone production utilizes several techniques (corona discharge, ultra violet radiation and electrolysis). This experiment aimed to evaluating effect of voltage and gas flow rate on ozone production with corona discharge. The system consists of two net-type stainless steel electrode placed in a dielectric barrier. Three pulsed voltage (20, 30, 40 KV) and flow rate (5, 10, 15 L/min) were prepare for operation variable at high frequency (3.7 kHz) with AC pulsed power supply. The dissolved ozone concentration depends on the applied high-voltage level, gas flow rate and the discharge exposure duration. The ozone concentration increases with decreasing gas flow rate. Dissolved ozone concentrations greater than 200 ppm can be obtained with a minimum voltage 40 kV.

Influence of total soluble salt concentration on growth and elemental concentration of winged bean seedlings, Psophocarpus tetragonolobus (L. ) DC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Csizinszky, A.A.

Winged bean (Psophocarpus tetragonolobus) (L.) DC) seedlings of the accession TPT-1, were grown in a greenhouse with graded, balanced total soluble salt (TSS) concentrations. After 45 days, plant height increased quadratically, with a maximum (149 cm) at 3000 ppm TSS. Seedlings were shortest at 1000 and 10,000 ppm TSS, 44.0 and 79.0 cm, respectively. Fresh weight of shoots increased quadratically with greatest weight, 29.03 g, at 5000 ppm TSS. Percent dry matter increased linearly with increasing TSS. Concentration of N, K and P increased quadratically with an increase in the TSS concentration in the growth medium. Concentration of Ca decreasedmore » quadratically with increasing TSS. Among the micronutrients, Fe and Mo concentration was quadratic, both elements were highest in the seedlings at 1000 and 10,000 ppm TSS rates. Concentrations of Mn and Zn increased linearly with increasing TSS. Winged bean seedlings at the 1000 to 3000 ppm TSS rates had spindly stems and a sparse, yellow foliage, typical for winged bean seedlings observed in the field during the first 4 to 5 weeks of growth. Seedlings at the 4000 and 5000 ppm TSS rates had sturdy stems and an abundant green foliage. At higher TSS concentrations, 5000 to 10,000 ppm TSS, seedlings had short intermodes and dark green foliage.« less

Summary and evaluation of the quality of stormwater in Denver, Colorado, 2006-2010

USGS Publications Warehouse

Stevens, Michael R.; Slaughter, Cecil B.

2012-01-01

Stormwater in the Denver area was sampled by the U.S. Geological Survey, in cooperation with the Urban Drainage and Flood Control District, in a network of 5 monitoring stations - 3 on the South Platte River and 2 on streams tributary to the South Platte River, Sand Creek, and Toll Gate Creek beginning in January 2006 and continuing through December 2010. Stormwater samples were analyzed at the U.S. Geological Survey National Water Quality Laboratory during 2006-2010 for water-quality properties such as pH, specific conductance, hardness, and residue on evaporation at 105 degrees Celsius; for constituents such as major ions (calcium, magnesium), organic carbon and nutrients, including ammonia plus organic nitrogen, ammonia, dissolved nitrite plus nitrate, total phosphorus, and orthophosphate; and for metals, including total recoverable and dissolved phases of copper, lead, manganese, and zinc. Samples collected during selected storms were also analyzed for bacteriological indicators such as Escherichia coli and fecal coliform at the Metro Wastewater Reclamation Laboratory. About 200 stormwater samples collected during storms characterize the quality of storm runoff during 2006-2010. In general, the quality of stormwater (2006-2010) has improved for many water-quality constituents, many of which had lower values and concentrations than those in stormwater collected in 2002-2005. However, the physical basis, processes, and the role of dilution that account for these changes are complex and beyond the scope of this report. The water-quality sampling results indicate few exceptions to standards except for dissolved manganese, dissolved zinc, and Escherichia coli. Stormwater collected at the South Platte River below Union Avenue station had about 10 percent acute or chronic dissolved manganese exceedances in samples; samples collected at the South Platte River at Denver station had less than 5 percent acute or chronic dissolved manganese exceedances. In contrast, samples collected at Toll Gate Creek above 6th Avenue at Aurora station, Sand Creek at mouth near Commerce City station, and the South Platte River at Henderson station, each had about 30 to 50 percent exceedances of both acute and chronic dissolved manganese standards. Of the samples collected at Sand Creek at mouth near Commerce City, 1 sample exceeded the acute standard and 4 samples exceeded the chronic standard for dissolved zinc, but no samples collected from the other sites exceeded either standard for zinc. Almost all samples of stormwater analyzed for Escherichia coli exceeded Colorado numeric standards. A numerical standard for fecal coliform is no longer applicable as of 2004. Results from the 2002-2005 study indicated that the general quality of stormwater had improved during 2002-2005 compared to 1998-2001, having fewer exceedances of Colorado standards, and showing downward trends for many water-quality values and concentrations. These trends coincided with general downward or relatively similar mean streamflows for the 2002-2005 compared to 1998-2001, which indicates that dilution may be a smaller influence on values and concentrations than other factors. For this report, downward trends were indicated for many constituents at each station during 2006-2010 compared to 2002-2005. The trends for mean streamflow for 2006-2010 compared to 2002-2005 are upward at all sites except for the South Platte River at Henderson, indicating that dilution by larger flows could be a factor in the downward concentration trends. At the South Platte River below Union Avenue station, downward trends were indicated for hardness, dissolved ammonia, dissolved orthophosphate, and dissolved copper. Upward trends at South Platte River below Union Avenue were indicated for pH. At the South Platte River at Denver station, downward trends were indicated for total ammonia plus organic nitrogen, dissolved ammonia, dissolved nitrite plus nitrate, dissolved orthophosphate, total phosphorus, dissolved organic carbon, and dissolved lead, manganese, and zinc, and total recoverable zinc. An upward trend in properties and constituents at South Platte River at Denver was indicated for pH. At Toll Gate Creek above 6th Avenue at Aurora, downward trends were indicated for residue on evaporation, total ammonia plus organic nitrogen, dissolved ammonia, dissolved orthophosphate, total phosphorus, and total recoverable copper, lead, manganese, and zinc. Upward trends in properties and constituents at Toll Gate Creek above 6th Avenue at Aurora were indicated for pH, specific conductance, and dissolved nitrite plus nitrate. At Sand Creek at mouth near Commerce City, downward trends were indicated for hardness, dissolved calcium, total ammonia plus organic nitrogen, and dissolved ammonia, orthophosphate, manganese, and zinc. An upward trend in properties and constituents at Sand Creek at mouth near Commerce City was indicated for pH. Downward trends at South Platte River at Henderson were indicated for specific conductance, hardness, dissolved magnesium, residue on evaporation, total ammonia plus organic nitrogen, dissolved ammonia, dissolved nitrite plus nitrate, dissolved orthophosphate, total phosphorus, dissolved lead and manganese, and total recoverable copper, lead, manganese, and zinc.

Does high diurnal variability in a reef flat from Ofu, American Samoa confer resistance to ocean acidification?

NASA Astrophysics Data System (ADS)

Koweek, D.; Samuel, L.; Mucciarone, D. A.; Woodson, C. B.; Monismith, S. G.; Dunbar, R. B.

2012-12-01

Forecasts for coral reefs under various ocean acidification scenarios are becoming increasingly complex due to significant inter-site variability in biogeochemistry, ecology, and physical oceanography. The reef flats of Ofu, American Samoa are a potential end-member of this vulnerability spectrum due to extremely high diurnal variability in their biogeochemistry. Here we present coupled biogeochemical and physical oceanographic measurements from a shallow reef flat on Ofu in November 2011. We observed diurnal temperature ranges of up to 7°C, along with diurnal pH and dissolved oxygen ranges of 0.6 units, and 160 percent of saturation, respectively. Carbon system measurements were less extreme. Alkalinity varied between 2240-2360 μmol/kg and total dissolved inorganic carbon (TDIC) ranged between 1850-2100 μmol/kg during the diurnal cycle. These observations suggest diurnal ranges of ~240ppm CO2 and 1.5 units of ΩAr. The larger diurnal range in TDIC relative to alkalinity suggests a reef environment dominated by photosynthesis. From these observations, we explore the balance between the dominant biogeochemical processes of production and calcification on the reef flat in more detail, along with its implication for conferring resistance to ocean acidification. We use calcification rate estimates to provide insight to patterns of day and night growth and/or dissolution on the reef. Finally, we present evidence of tidal modulation of the biogeochemical signals and discuss the role of localized physical circulation in helping to determine a reef's vulnerability to ocean acidification.

NMR evaluation of total statin content and HMG-CoA reductase inhibition in red yeast rice (Monascus spp.) food supplements

PubMed Central

2012-01-01

Background Red yeast rice (i.e., rice fermented with Monascus spp.), as a food supplement, is claimed to be blood cholesterol-lowering. The red yeast rice constituent monacolin K, also known as lovastatin, is an inhibitor of the hydroxymethylglutaryl-CoA (HMG-CoA) reductase. This article aims to develop a sensitive nuclear magnetic resonance (NMR) method to determine the total statin content of red yeast rice products. Methods The total statin content was determined by a 400 MHz 1H NMR spectroscopic method, based on the integration of the multiplet at δ 5.37-5.32 ppm of a hydrogen at the hexahydronaphthalene moiety in comparison to an external calibration with lovastatin. The activity of HMG-CoA reductase was measured by a commercial spectrophotometric assay kit. Results The NMR detection limit for total statins was 6 mg/L (equivalent to 0.3 mg/capsule, if two capsules are dissolved in 50 mL ethanol). The relative standard deviations were consistently lower than 11%. The total statin concentrations of five red yeast rice supplements were between 1.5 and 25.2 mg per specified daily dose. A dose-dependent inhibition of the HMG-CoA reductase enzyme activity by the red yeast rice products was demonstrated. Conclusion A simple and direct NMR assay was developed to determine the total statin content in red yeast rice. The assay can be applied for the determination of statin content for the regulatory control of red yeast rice products. PMID:22439629

Essential oils have different effects on human pathogenic and commensal bacteria in mixed faecal fermentations compared with pure cultures.

PubMed

Thapa, Dinesh; Louis, Petra; Losa, Riccardo; Zweifel, Béatrice; Wallace, R John

2015-02-01

A static batch culture system inoculated with human faeces was used to determine the influence of essential oil compounds (EOCs) on mixed faecal microbiota. Bacteria were quantified using quantitative PCR of 16S rRNA genes. Incubation for 24 h of diluted faeces from six individuals caused enrichment of Bifidobacterium spp., but proportions of other major groups were unaffected. Thymol and geraniol at 500 p.p.m. suppressed total bacteria, resulting in minimal fermentation. Thymol at 100 p.p.m. had no effect, nor did eugenol or nerolidol at 100 or 500 p.p.m. except for a slight suppression of Eubacterium hallii. Methyl isoeugenol at 100 or 500 p.p.m. suppressed the growth of total bacteria, accompanied by a large fall in the molar proportion of propionate formed. The relative abundance of Faecalibacterium prausnitzii was unaffected except with thymol at 500 p.p.m. The ability of EOCs to control numbers of the pathogen Clostridium difficile was investigated in a separate experiment, in which the faecal suspensions were amended by the addition of pure culture of C. difficile. Numbers of C. difficile were suppressed by thymol and methyl isoeugenol at 500 p.p.m. and to a lesser extent at 100 p.p.m. Eugenol and geraniol gave rather similar suppression of C. difficile numbers at both 100 and 500 p.p.m. Nerolidol had no significant effect. It was concluded from these and previous pure-culture experiments that thymol and geraniol at around 100 p.p.m. could be effective in suppressing pathogens in the small intestine, with no concern for beneficial commensal colonic bacteria in the distal gut. © 2015 The Authors.

Residue of organochlorine compounds and mercury in birds' eggs from the Niagara Peninsula, Ontario.

PubMed

Frank, R; Holdrinet, M V

1975-01-01

Eggs (307) were collected in 1971 from twenty species of birds with a variety of feeding habits from the Niagara Peninsula. This area of ontario is intensively developed for agriculture and heavy industry and has a large urban population. Representative species were obtained from both the terrestrial and aquatic food chains. Eggs were analyzed for organochlorine insecticides, polychlorinated biphenyls, and total mercury. Eggs from carnivorous species at the top of the aquatic food chain had the highest mean residues of signa DDT(7.6to 22.4 pm), PCB (3.5 to 74.0 ppm) and total mercury (0.64 to 0.83 ppm). Eggs from some terrestrial carnivores (red-tailed hawk and great horned owl) also had relatively high residues (2.5 to 3.9 ppm of sigmaDDT, 0.2 to 1.0 ppm of PCB, 0.06 to 0.09 ppm of mercury, however levels were much lower than those found in eggs from aquatic-feeding carnivores. Eggs from one red-shouldered hawk had residues comparable to the aquatic feeding carnivores. Eggs from herbivorous and insectivorous birds of both aquatic and terrestrial environments contained much lower residues. PCB residues were slightly lower in eggs among the terrestrial feeding species (0.05 to 2.0 ppm) than among the aquatic feeders (0.14 to4.0 ppm) and tended to be lower in eggs from terrestrial species collected in rural than incity environs. Levels of sigmaDDT were similar in both groups with eggs from terrestrial feeders containing mean resisues between 0.15 and 2.64 ppm and those from aquatic feeders between 0.33 and 2.79 ppm.

Evidence of a Pre-eruptive Fluid Phase for the Millennium Eruption, Paektu Volcano, North Korea

NASA Astrophysics Data System (ADS)

Iacovino, K.; Sisson, T. W.; Lowenstern, J. B.

2014-12-01

We present initial results of a study of comenditic to trachytic melt inclusions from the Millennium Eruption (ME) of Paektu volcano (AD 946; VEI≥7; 25 km3 DRE). Paektu volcano (aka Changbaishan) is a remote and poorly studied intraplate stratovolcano whose 37 km2 caldera is bisected by the political border between North Korea and China, limiting studies of its proximal deposits. ME magmas are predominantly phenocryst-poor (≤3 vol%) comendites plus a volumetrically minor late-stage, more phenocryst-rich (10-20 vol%) trachyte. Sizeable (100-500 µm diameter) glassy but bubble-bearing melt inclusions are widespread in anorthoclase and hedenbergite phenocrysts, as well as in rarer quartz and fayalite phenocrysts. Comparing the relative enrichments of incompatible volatile and non-volatile elements in melt inclusions along a liquid line of descent shows decreasing volatile/Zr ratios suggesting the partitioning of volatiles into a fluid phase. This suggests that current gas-yield estimates (Horn & Schminke, 2000) for the ME, based on the petrologic method (difference in volatiles between melt inclusions and matrix glass), could be severe underestimates. Establishing the composition and quantity of a pre-eruptive fluid phase is the primary goal of this study and has implications for eruption triggering and for modeling the climatic effects of one of the largest eruptions in the last 10,000 years. Including results from Horne and Schminke (2000), melt inclusions from within a single pumice fall unit show a wide range in dissolved volatile contents and magma chemistries. Concentrations of H2O are moderate (2-3.5 wt% via FTIR), with Cl and F ranging from 500-4600 ppm and 1100-4700 ppm (via EPMA). CO2 is below the detection limit of 2 ppm (FTIR with N2 purge) in bubble-bearing melt inclusions, but is detectable (≤56 ppm) in melt inclusions homogenized at 100 MPa and 850-900 °C for ~30 min (conditions also leading to reduction of dissolved H2O to 0.6-2 wt%). Characterization of a co-existing fluid phase in ME magmas is being investigated with further melt inclusion analyses, mineral-melt-fluid equilibrium calculations, and phase equilibrium experiments on fluid-saturated liquid lines of descent and on volatile solubilities of the ME trachyite-comendite suite.

Study on Magnesium in Rainwater and Fertilizer Infiltration to Solidified Peat

NASA Astrophysics Data System (ADS)

Tajuddin, S. A. M.; Rahman, J. A.; Mohamed, R. M. S. R.

2018-04-01

Magnesium is a component of several primary and secondary minerals in the soil which are essentially insoluble for agricultural purpose. The presence of water infiltrate in the soil allows magnesium to dissolve together into the groundwater. In fertilizers, magnesium is categorized as secondary macronutrient which supplies food and encouraging for plants growth. The main objective of this study was to determine the concentration of magnesium in fibric peat when applied the solidification under different conditions. Physical model was used as a mechanism for the analysis of the experimental data using a soil column as an equipment to produce water leaching. In this investigation, there were four outlets in the soil column which were prepared from the top of the column to the bottom with the purpose of identifying the concentration of magnesium for each soil level. The water leaching of each outlet was tested using atomic absorption spectroscopy (AAS). The results obtained showed that the highest concentrations of magnesium for flush and control condition at outlet 4 was 12.50 ppm and 1.29 ppm respectively. Similarly, fibric with solidified peat under rainwater recorded the highest value of 3.16 at outlet 1 for wet condition while for dry condition at outlet 4 of 1.33 ppm. However, the difference in fibric with solidified peat under rainwater and fertilizer condition showed that the highest value for the wet condition was achieved at outlet 1 with 5.43 ppm while highest value of 1.26 ppm was obtained for the dry condition at the outlet 4. It was concluded that the outlets in the soil column gave a detailed analysis of the concentration of magnesium in the soil which was influenced by the environmental conditions.

Tropical surface water quality studies: Implications for the aquatic fate of N-methyl carbamate pesticides.

PubMed

Ha, Bao; Zamini, Leili; Monn, Jeremy; Njoroge, Samuel; Thimo, Laban; Ondeti, Maria; Murungi, Jane I; Muhoro, Clare N

2018-03-04

Water quality assessment was conducted on the Ruiru River, a tributary of an important tropical river system in Kenya, to determine baseline river conditions for studies on the aquatic fate of N-methyl carbamate (NMC) pesticides. Measurements were taken at the end of the long rainy season in early June 2013. Concentrations of copper (0.21-1.51 ppm), nitrates (2.28-4.89 ppm) and phosphates (0.01-0.50 ppm) were detected at higher values than in uncontaminated waters, and attributed to surface runoff from agricultural activity in the surrounding area. Concentrations of dissolved oxygen (8-10 ppm), ammonia (0.02-0.22 ppm) and phenols (0.19-0.83 ppm) were found to lie within normal ranges. The Ruiru River was found to be slightly basic (pH 7.08-7.70) with a temperature of 17.8-21.2°C. The half-life values for hydrolysis of three NMC pesticides (carbofuran, carbaryl and propoxur) used in the area were measured under laboratory conditions, revealing that rates of decay were influenced by the electronic nature of the NMCs. The hydrolysis half-lives at pH 9 and 18°C decreased in the order carbofuran (57.8 h) > propoxur (38.5 h) > carbaryl (19.3 h). In general, a decrease in the electron density of the NMC aromatic ring increases the acidity of the N-bound proton removed in the rate-limiting step of the hydrolysis mechanism. Our results are consistent with this prediction, and the most electron-poor NMC (carbaryl) hydrolyzed fastest, while the most electron-rich NMC (carbofuran) hydrolyzed slowest. Results from this study should provide baseline data for future studies on NMC pesticide chemical fate in the Ruiru River and similar tropical water systems.

Effect of Sulfur in Steel on Transient Evolution of Inclusions During Calcium Treatment

NASA Astrophysics Data System (ADS)

Liu, Yang; Zhang, Lifeng; Zhang, Ying; Duan, Haojian; Ren, Ying; Yang, Wen

2018-04-01

In the current study, the effect of S content in the molten steel on inclusions during calcium treatment was studied using an induction furnace. The calcium in steel decreased from 48 to 2 ppm, and the sulfur in steel changed a little with time. When sulfur content in steel was as low as 25 ppm during calcium treatment, inclusions shifted from CaO-Al2O3-CaS to Al2O3-CaO with about 35 pct CaO. When the sulfur increased over 90 ppm, more CaS-CaO formed just after the addition of calcium, and then the CaS content decreased from over 45 pct to lower than 15 pct and inclusions were mostly Al2O3-CaO-CaS and Al2O3-CaO with a high Al2O3 content. Thermodynamic calculation predicted the variation of the composition of inclusions, indicating good agreement with the measurement, while a certain deviation existed, especially for heats with 90 and 180 ppm sulfur. A reaction model was proposed for the formation of CaO and CaS, which considered the reaction between calcium vapor bubbles in the zone and the dissolved oxygen and sulfur in the molten steel, as described by a Langmuir-type adsorption isotherm with a reaction occurring on the remaining vacant sites. The variation of transient CaS inclusions was discussed based on the thermodynamic calculation and the morphology evolution of typical inclusions containing CaS.

Individual contributions, provision point mechanisms and project cost information effects on contingent values: Findings from a field validity test.

PubMed

Christantoni, Maria; Damigos, Dimitris

2018-05-15

In many instances, Contingent Valuation practitioners rely on voluntary monetary contributions, despite the fact that they are deemed to be neither incentive compatible in theory nor demand revealing in practice. The reason is that they are suitable for most field applications and offer benefits that may outweigh their drawbacks. This paper endeavors to contribute to the literature by exploring the effect of donation payments with differing incentive structures and information levels on contingent values and on respondents' uncertainty regarding the donations declared. To this end, a field survey was conducted using a sample of 332 respondents who were randomly assigned to one of three different mechanisms: (1) individual contribution (hereinafter CVM treatment); (2) individual contribution with provision point mechanism (PPM), where the total cost of the project is unknown (hereinafter PPM treatment); and (3) individual contribution with PPM, where the total cost of the project is known (hereinafter PPM-INF treatment). The results indicate that there are no statistically significant differences in willingness to pay (WTP) estimates between the CVM and PPM treatments nor between the PPM and the PPM-INF treatments. The results also indicate that the PPM has a positive effect on respondents' certainty level, but there is no evidence that the certainty level is affected by the project information cost. The results are mixed compared to previous research efforts. Thus, further tests are necessary in field comparisons and under different information environments before any definite recommendations can be made. Copyright © 2017 Elsevier B.V. All rights reserved.

Efficacy of detergents and fresh produce disinfectants against microorganisms associated with mixed raw vegetables.

PubMed

Samadi, Nasrin; Abadian, Neda; Bakhtiari, Donya; Fazeli, Mohammad Reza; Jamalifar, Hossein

2009-07-01

Efficacy of commercial detergent and disinfectants to eliminate microorganisms associated with fresh vegetables eaten raw in Iran, including radish, parsley, basil, coriander (cilantro), Allium porrum (leek), and peppermint were studied. The raw vegetables were subjected to a triple wash treatment of washing in tap water for mud removal, washing in water containing a detergent (dishwashing liquid) or disinfectant individually, and rinsing in tap water. The population of total mesophilic microbes on the surface of untreated vegetables ranged from 10(5) to 10(6) CFU/g. Washing in tap water or treatment with detergent (333 ppm for 10 min) or benzalkonium chloride (92 ppm for 15 min) reduced the total microbial count, most probable number (MPN) of coliforms, MPN of fecal coliforms, and MPN of fecal streptococci by about 1.2 to 2.3 log. No significant differences in microbial populations were found on vegetables after decontamination with tap water, detergent, or benzalkonium chloride (P > 0.05). Treatments with peracetic acid (100 ppm for 15 min) and hydrogen peroxide (133 ppm for 30 min) reduced the total mesophilic microbial counts by about 2.8 log. The microbial reductions with calcium hypochlorite (300 ppm for 15 min) and combined hydrogen peroxide and silver ion (133 ppm for 30 min) were significantly higher than those obtained after rinsing in tap water or after detergent or benzalkonium chloride wash (P < 0.05). Pretreatment with detergent slightly enhanced the efficacy of all decontamination treatments, but results were not significantly different from those obtained after individual application of disinfectants.

Evaluation of the Multi-Chambered Treatment Train, a retrofit water-quality management device

USGS Publications Warehouse

Corsi, Steven R.; Greb, Steven R.; Bannerman, Roger T.; Pitt, Robert E.

1999-01-01

This paper presents the results of an evaluation of the benefits and efficiencies of a device called the Multi-Chambered Treatment Train (MCTT), which was installed below the pavement surface at a municipal maintenance garage and parking facility in Milwaukee, Wisconsin. Flow-weighted water samples were collected at the inlet and outlet of the device during 15 storms, and the efficiency of the device was based on reductions in the loads of 68 chemical constituents and organic compounds. High reduction efficiencies were achieved for all particulate-associated constituents, including total suspended solids (98 percent), total phosphorus (88 percent), and total recoverable zinc (91 percent). Reduction rates for dissolved fractions of the constituents were substantial, but somewhat lower (dissolved solids, 13 percent; dissolved phosphorus, 78 percent; dissolved zinc, 68 percent). The total dissolved solids load, which originated from road salt storage, was more than four times the total suspended solids load. No appreciable difference was detected between particle-size distributions in inflow and outflow samples.

42 CFR 84.253 - Chemical-cartridge respirators; requirements and tests.

Code of Federal Regulations, 2010 CFR

2010-10-01

... cartridges or pairs of cartridges continuously at a concentration of 10 ppm vinyl chloride monomer at a total... respirator by a breathing machine at a concentration of 10 ppm vinyl chloride monomer at the rate of 24...

A novel method for the determination of synthetic colors in ice cream samples.

PubMed

Tripathi, Meenakshi; Khanna, Subhash K; Das, Mukul

2004-01-01

A simple method has been developed for the extraction, separation, and determination of synthetic colors in ice cream samples. The process involves the breakdown of emulsion by neutral detergents (Triton X-100 and Tween 20) followed by extraction with petroleum ether for removal of fat. The aqueous colored solution obtained is treated with 5% acetic acid, and the uptake of color is carried out by a wool-dyeing technique. The color is eluted from the wool with 5% ammonia solution, the solution is evaporated to dryness, and the residue is dissolved in 60% ethanol for paper chromatography using trisodium citrate-ammonia-water (2 + 5 + 95, w/v/v) as the mobile phase. The colored spots from the paper chromatogram are cut and eluted with 60% ethanol, and the absorbance is measured at the respective lambda maximum corresponding to the Rf value of the appropriate standard. The recoveries of 6 colors, including sunset yellow FCF (SSYFCF), tartrazine, carmoisine, ponceau 4R, brilliant blue FCF (BBFCF), and fast green FCF from spiked samples with either detergent were found to be >90%. However, recoveries of erythrosine were 21 and 65% with Triton X-100 and Tween 20, respectively. Indigo carmine could not be recovered at all because of its fugitive property in 5% ammonia solution, which is used to strip the color from the wool. The sensitivity of the method with the use of Tween 20 is 1 ppm (1 microg/g) for the colors in spiked ice cream samples. With this method, we analyzed samples of 20 branded colored ice cream. The results showed the presence of tartrazine (8.4-43.3 ppm), SSYFCF (23.5-117.6 ppm), carmoisine (traces-53.2 ppm), erythrosine (3.5 ppm), and BBFCF (4.1 ppm) in the ice cream samples. Apart from 2 samples of tuttifruity, all of the ice cream samples showed the presence of permitted synthetic colors below the permissible level of 100 ppm established by the Prevention of Food Adulteration Act of India.

The effect of ozonated cooling water on the corrosion behavior of stainless steel, titanium and copper alloys. Ozone biocidal action on sessile and planktonic bacteria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Videla, H.A.; Guiamet, P.S.; Mele, M.F.L. de

1999-11-01

Two aspects of ozone utilization as sole chemical treatment for cooling water demand a better understanding: (a) the effect of dissolved ozone on the corrosion behavior of heat exchanger structural materials and (b) the biocidal action of ozone on bacterial biofilms. To assess the effect of ozone dissolved in synthetic cooling water on the corrosion behavior of different structural materials (stainless steel; 70:30 copper-nickel; aluminum brass and titanium), voltamperometric experiments and corrosion potential vs. time measurements were made at ozone concentrations between 0.1 and 1.2 ppm. Present results show that the passive behavior of stainless steel and titanium is notmore » affected by dissolved ozone whereas copper alloys are susceptible to corrosion in the presence of ozone. To study the biocidal action of various concentrations of dissolved ozone against planktonic and sessile bacteria, liquid cultures and biofilms of Pseudomonas fluorescense, formed on different structural materials, were used at different contact times. The results show that dissolved ozone is an effective biocide for controlling planktonic cells but its effectiveness decreases in the presence of sessile bacteria and the extracellular polymeric matrix of the biofilm. It is suggested that the penetration of ozone through the biofilm depends on the simultaneous diffusion and reaction of the biocide with the biofilm matrix which may exhibit local differences in biomass distribution and hydrodynamic conditions.« less

Quality-assurance data, comparison to water-quality standards, and site considerations for total dissolved gas and water temperature, lower Columbia River, Oregon and Washington, 2001

USGS Publications Warehouse

Tanner, Dwight Q.; Bragg, Heather M.

2002-03-06

At times in July and August 2001, the total-dissolved-gas probe at Warrendale could not be positioned below the minimum compensation depth because the river was too shallow at that location. Consequently, degassing at probe depth may have occurred, and total dissolved gas may have been larger in locations with greater depths.

Salinity of deep groundwater in California: Water quantity, quality, and protection.

PubMed

Kang, Mary; Jackson, Robert B

2016-07-12

Deep groundwater aquifers are poorly characterized but could yield important sources of water in California and elsewhere. Deep aquifers have been developed for oil and gas extraction, and this activity has created both valuable data and risks to groundwater quality. Assessing groundwater quantity and quality requires baseline data and a monitoring framework for evaluating impacts. We analyze 938 chemical, geological, and depth data points from 360 oil/gas fields across eight counties in California and depth data from 34,392 oil and gas wells. By expanding previous groundwater volume estimates from depths of 305 m to 3,000 m in California's Central Valley, an important agricultural region with growing groundwater demands, fresh [<3,000 ppm total dissolved solids (TDS)] groundwater volume is almost tripled to 2,700 km(3), most of it found shallower than 1,000 m. The 3,000-m depth zone also provides 3,900 km(3) of fresh and saline water, not previously estimated, that can be categorized as underground sources of drinking water (USDWs; <10,000 ppm TDS). Up to 19% and 35% of oil/gas activities have occurred directly in freshwater zones and USDWs, respectively, in the eight counties. Deeper activities, such as wastewater injection, may also pose a potential threat to groundwater, especially USDWs. Our findings indicate that California's Central Valley alone has close to three times the volume of fresh groundwater and four times the volume of USDWs than previous estimates suggest. Therefore, efforts to monitor and protect deeper, saline groundwater resources are needed in California and beyond.

Salinity of deep groundwater in California: Water quantity, quality, and protection

PubMed Central

Kang, Mary; Jackson, Robert B.

2016-01-01

Deep groundwater aquifers are poorly characterized but could yield important sources of water in California and elsewhere. Deep aquifers have been developed for oil and gas extraction, and this activity has created both valuable data and risks to groundwater quality. Assessing groundwater quantity and quality requires baseline data and a monitoring framework for evaluating impacts. We analyze 938 chemical, geological, and depth data points from 360 oil/gas fields across eight counties in California and depth data from 34,392 oil and gas wells. By expanding previous groundwater volume estimates from depths of 305 m to 3,000 m in California’s Central Valley, an important agricultural region with growing groundwater demands, fresh [<3,000 ppm total dissolved solids (TDS)] groundwater volume is almost tripled to 2,700 km3, most of it found shallower than 1,000 m. The 3,000-m depth zone also provides 3,900 km3 of fresh and saline water, not previously estimated, that can be categorized as underground sources of drinking water (USDWs; <10,000 ppm TDS). Up to 19% and 35% of oil/gas activities have occurred directly in freshwater zones and USDWs, respectively, in the eight counties. Deeper activities, such as wastewater injection, may also pose a potential threat to groundwater, especially USDWs. Our findings indicate that California’s Central Valley alone has close to three times the volume of fresh groundwater and four times the volume of USDWs than previous estimates suggest. Therefore, efforts to monitor and protect deeper, saline groundwater resources are needed in California and beyond. PMID:27354527

Field testing of lake water chemistry with a portable and an AUV-based mass spectrometer.

PubMed

Hemond, Harry F; Mueller, Amy V; Hemond, Michael

2008-10-01

Two mass spectrometers (MS) are tested for the measurement of volatile substances, such as hydrocarbons and metabolic gases, in natural waters. KOALA is a backpackable MS operated from above the water surface, in which samples are pumped through a flow cell using a syringe. NEREUS is an underwater instrument hosted by an autonomous underwater vehicle (AUV) that is linked to a communications network to provide chemical data in real time. The mass analyzers of the two MS are nearly identical cycloids, and both use flat-plate membrane inlets. Testing took place in an eutrophic, thermally stratified lake exhibiting steep chemical gradients and significant levels of methane. KOALA provided rapid multispecies analysis of dissolved gases, with a detection limit for methane of 0.1 ppm (readily extendable to 0.01 ppm) and savings of time of at least a factor of 10 compared to that of conventional analysis. The AUV-mounted NEREUS additionally provided rapid spatial coverage and the capability of performing chemical surveys autonomously. Tests demonstrated the need for temperature control of a membrane inlet when steep thermal gradients are present in a water body, as well as the benefits of co-locating all sensors on the AUV to avoid interference from chemically different waters entering and draining from the free-flooding outer hull. The ability to measure dissolved volatiles provided by MS offers potential for complementarity with ionic sensors in the study of natural waters, such as in the case of the carbonate system.

Atrazine removal from water by polycation-clay composites: effect of dissolved organic matter and comparison to activated carbon.

PubMed

Zadaka, Dikla; Nir, Shlomo; Radian, Adi; Mishael, Yael G

2009-02-01

Atrazine removal from water by two polycations pre-adsorbed on montmorillonite was studied. Batch experiments demonstrated that the most suitable composite poly (4-vinylpyridine-co-styrene)-montmorillonite (PVP-co-S90%-mont.) removed 90-99% of atrazine (0.5-28 ppm) within 20-40 min at 0.367% w/w. Calculations employing Langmuir's equation could simulate and predict the kinetics and final extents of atrazine adsorption. Column filter experiments (columns 20x1.6 cm) which included 2g of the PVP-co-S90%-mont. composite mixed with excess sand removed 93-96% of atrazine (800 ppb) for the first 800 pore volumes, whereas the same amount of granular activated carbon (GAC) removed 83-75%. In the presence of dissolved organic matter (DOM; 3.7 ppm) the efficiency of the GAC filter to remove atrazine decreased significantly (68-52% removal), whereas the corresponding efficiency of the PVP-co-S90%-mont. filter was only slightly influenced by DOM. At lower atrazine concentration (7 ppb) the PVP-co-S90%-mont. filter reduced even after 3000 pore volumes the emerging atrazine concentration below 3 ppb (USEPA standard). In the case of the GAC filter the emerging atrazine concentration was between 2.4 and 5.3 microg/L even for the first 100 pore volumes. Thus, the PVP-co-S90%-mont. composite is a new efficient material for the removal of atrazine from water.

Pharmacokinetic and Genomic Effects of Arsenite in Drinking Water on Mouse Lung in a 30-Day Exposure

PubMed Central

Chilakapati, Jaya; Wallace, Kathleen; Hernandez-Zavala, Araceli; Moore, Tanya; Ren, Hongzu

2015-01-01

The 2 objectives of this subchronic study were to determine the arsenite drinking water exposure dependent increases in female C3H mouse liver and lung tissue arsenicals and to characterize the dose response (to 0, 0.05, 0.25, 1, 10, and 85 ppm arsenite in drinking water for 30 days and a purified AIN-93M diet) for genomic mouse lung expression patterns. Mouse lungs were analyzed for inorganic arsenic, monomethylated, and dimethylated arsenicals by hydride generation atomic absorption spectroscopy. The total lung mean arsenical levels were 1.4, 22.5, 30.1, 50.9, 105.3, and 316.4 ng/g lung tissue after 0, 0.05, 0.25, 1, 10, and 85 ppm, respectively. At 85 ppm, the total mean lung arsenical levels increased 14-fold and 131-fold when compared to either the lowest noncontrol dose (0.05 ppm) or the control dose, respectively. We found that arsenic exposure elicited minimal numbers of differentially expressed genes (DEGs; 77, 38, 90, 87, and 87 DEGs) after 0.05, 0.25, 1, 10, and 85 ppm, respectively, which were associated with cardiovascular disease, development, differentiation, apoptosis, proliferation, and stress response. After 30 days of arsenite exposure, this study showed monotonic increases in mouse lung arsenical (total arsenic and dimethylarsinic acid) concentrations but no clear dose-related increases in DEG numbers. PMID:26674514

Pharmacokinetic and Genomic Effects of Arsenite in Drinking Water on Mouse Lung in a 30-Day Exposure.

PubMed

Chilakapati, Jaya; Wallace, Kathleen; Hernandez-Zavala, Araceli; Moore, Tanya; Ren, Hongzu; Kitchin, Kirk T

2015-01-01

The 2 objectives of this subchronic study were to determine the arsenite drinking water exposure dependent increases in female C3H mouse liver and lung tissue arsenicals and to characterize the dose response (to 0, 0.05, 0.25, 1, 10, and 85 ppm arsenite in drinking water for 30 days and a purified AIN-93M diet) for genomic mouse lung expression patterns. Mouse lungs were analyzed for inorganic arsenic, monomethylated, and dimethylated arsenicals by hydride generation atomic absorption spectroscopy. The total lung mean arsenical levels were 1.4, 22.5, 30.1, 50.9, 105.3, and 316.4 ng/g lung tissue after 0, 0.05, 0.25, 1, 10, and 85 ppm, respectively. At 85 ppm, the total mean lung arsenical levels increased 14-fold and 131-fold when compared to either the lowest noncontrol dose (0.05 ppm) or the control dose, respectively. We found that arsenic exposure elicited minimal numbers of differentially expressed genes (DEGs; 77, 38, 90, 87, and 87 DEGs) after 0.05, 0.25, 1, 10, and 85 ppm, respectively, which were associated with cardiovascular disease, development, differentiation, apoptosis, proliferation, and stress response. After 30 days of arsenite exposure, this study showed monotonic increases in mouse lung arsenical (total arsenic and dimethylarsinic acid) concentrations but no clear dose-related increases in DEG numbers.

Antioxidative efficiency of Triticum aestivum L. exposed to chromium stress.

PubMed

Dey, Surjendu Kumar; Jena, Priyanka Priyadarshani; Kundu, Satyajit

2009-07-01

Wheat (Triticum aestivum L. cv Sonalika) seedlings were grown in presence of K2Cr2O7 (10, 50 and 100 ppm) for 7 days and growth, total chlorophyll, activities of antioxidative enzymes like superoxide dismutase (SOD; EC 1.15.1.1), catalase (CAT; EC 1.11.1.6) and guaiacol peroxidase (POX; EC 1.11.1.7) and lipid peroxidation were determined in root and shoot tissues. Growth of the seedlings was significantly (p < or = 0.05) depressed and at 100 ppm, root length was reduced by 63% and shoot length by 44% in comparison to the respective controls. Total chlorophyll loss in shoots was about 46% at 10 ppm of K2Cr2O7 which further increased to 80% at 100 ppm. Both in root and shoot tissues, activities of SOD and CAT declined with increase of metal in growth medium and it was significant (p < or = 0.05) even at lowest concentration of the metal tested. But POX activity showed a different trend. In root tissues it was decreased whereas in shoots, there was many fold increase in the activity (about 370% over control at 100 ppm). Malondialdehyde (MDA) content increased both in root and shoot tissues, but it reached significant (p < 0.05) level at 50 ppm in roots and at 100 ppm in shoot tissues. Even though antioxidative enzyme activities were not assayed in germinating embryos, inhibition in germination percentage (by 40% at 100 ppm) and increase in lipid peroxidation level (by 71% over control at 100 ppm) were observed in 2-day-old embryos, germinated in presence of K2Cr2O7 (10, 50 and 100 ppm). The results indicated the imposition of oxidative stress situations both during germination and early stages of seedling growth by Cr6 stress, which might be one of the probable reasons behind Cr toxicity in plants.

Minor and Trace Element Chemistry of Urban NS-Soot from the Central Valley of CA, USA

NASA Astrophysics Data System (ADS)

Kleich, S. J.; Hooper, R.

2017-12-01

During a recent study of metal transport in the Central Valley of California, it was noted that ns-soot (soot) occurred as complex clusters of graphene-like spheres admixed with other aerosols and were usually the dominant component of PM2.5 air particulates. These soot clusters contained a wide variety of metals of environmental concern such as As,Pb,Cr, and Ni. This study reports semi-quantitative results for 20 minor and trace elements (calibrated with Smithsonian microbeam standards) using a 200kV Transmission Electron Microscope, EDS, and SAED. This study also examined the mineralogy and crystallinity of admixed aerosols within composite soot clusters. Samples selected represent three contrasting urban settings in the Central Valley: Woodland, on the western side of the valley (Interstate highway to the east); Stockton, an inland sea-port and land transportation corridor in the center of the valley; and Roseville, a major rail-transport hub to the east. The wet/dry Mediterranean climate of California resulted in pronounced seasonal variations in total metal content. Soot cluster chemistry is highly variable however certain patterns emerged. Soot collected during the wet season is generally more aciniform, less structurally complex, and had lower sulfur (sulfate) concentrations but still had significant levels of transition metals (V,Cr,Mn,Fe,Ni,Zn and Pb) . Dry season soot was predominantly admixed with sulfate aerosols, and enriched in alkalis and alkaline earth metals. Stockton (wet-season) soot had up to 6000ppm of Pb. There is appreciable Pb (210ppm-2600ppm) in 38% of samples from Roseville but no Pb greater than 200ppm in Woodland. The highest overall total metals were found in Roseville soot with appreciable As(670ppm), V(100ppm), Pb(2600ppm), Zn(4000 ppm), Cr(90ppm), and Ni(300ppm). Heavy transport (road/rail/port) correlates with higher metal contents regardless of climate.

Geochemical and geophysical monitoring activities in Campo de Calatrava Volcanic Field (Spain)

NASA Astrophysics Data System (ADS)

Luengo-Oroz, Natividad; Villasante-Marcos, Víctor; López-Díaz, Rubén; Calvo, Marta; Albert, Helena; Domínguez Cerdeña, Itahiza

2017-04-01

The Campo de Calatrava Volcanic Field (CCVF) or Spanish Central Volcanic Zone is located in central continental Spain (Ciudad Real province) and covers about 5000 km2. It includes around 240 eruptive centers, mainly monogenetic basaltic cones but also explosive maar structures. According to K-Ar geochronology, its main activity phase occurred during Pliocene and Pleistocene epochs (between 5 and 1.7 Ma) and involved alkaline to ultraalkaline magmas, although an older ultrapotassic phase is dated around 8.7-6.4 Ma. However, some recent works have proposed Holocene ages for some of the volcanic products, opening the possibility of considering the CCVF "active" according to international standards. Responding to this situation, the Instituto Geográfico Nacional (IGN) has initiated geochemical and geophysical monitoring activities in the CCVF. Here, we describe these ongoing efforts and we report results about groundwater geochemistry at several natural highly-gaseous springs in the area (hervideros), as well as soil temperature, CO2 diffuse flux from the soil and electrical self-potential data mapped on a small degassing structure called La Sima. In order to analyze microseismicity or any seismic anomaly in the CCVF, a seismic station has also been installed close to this degassing structure. Physicochemical parameters (temperature, pH, Eh and electric conductivity) were measured in situ in four springs and samples were taken in order to analyze major ions and trace elements. Total composition of dissolved gases and helium isotopic ratios were also determined. To complete soil temperature, self-potential and gas prospections performed in La Sima, soil gases were sampled at the bottom of the structure at a depth of 20 cm. Analysis of the total gas composition found 957400 ppm of CO2. Low values of O2 and N2 were also detected (5600 and 24800 ppm respectively).

Interactive effect of elevated CO2 and temperature on coral physiology

NASA Astrophysics Data System (ADS)

Grottoli, A. G.; Cai, W.; Warner, M.; Melman, T.; Schoepf, V.; Baumann, J.; Matsui, Y.; Pettay, D. T.; Hoadley, K.; Xu, H.; Wang, Y.; Li, Q.; Hu, X.

2011-12-01

Increases in ocean acidification and temperature threaten coral reefs globally. However, the interactive effect of both lower pH and higher temperature on coral physiology and growth are poorly understood. Here, we present preliminary findings from a replicated controlled experiment where four species of corals (Acorpora millepora, Pocillopora damicornis, Montipora monasteriata, Turbinaria reniformis) were reared under the following six treatments for three weeks: 1) 400ppm CO2 and ambient temperature, 2) 400ppm CO2 and elevated temperature, 3) 650ppm CO2 and ambient temperature, 4) 650ppm CO2 and elevated temperature, 5) 800ppm CO2 and ambient temperature, 6) 800ppm CO2 and elevated temperature. Initial findings of photophysiological health (Fv/Fm), calcification rates (as measured by both buoyant weight and the total alkalinity methods), and energy reserves will be presented.

Declines in organochlorines in eggs of red-breasted mergansers from Lake Michigan, 1977-78 versus 1990

USGS Publications Warehouse

Heinz, G.H.; Miller, D.S.; Ebert, B.J.; Stromborg, K.L.

1994-01-01

From 1977-1978 to 1990, concentrations of polychlorinated biphenyls (PCBs) and most organochlorine pesticides declined in eggs of red-breasted mergansers (M ergus serrator) nesting on islands in northwestern Lake Michigan. Total PCBs decreased 60% (from 21 ppm in 1977-1978 to 8.5 ppm in 1990) and p, p'-DDE decreased 66% (from 6.5 to 2.2 ppm). Dieldrin decreased only 16% (from 0.82 to 0.69 ppm). In 1990, 79.1 % of incubated eggs hatched, which was not significantly different from the 83.5% that hatched in 1977-1978.

Solubility of water in lunar basalt at low pH2O

NASA Astrophysics Data System (ADS)

Newcombe, M. E.; Brett, A.; Beckett, J. R.; Baker, M. B.; Newman, S.; Guan, Y.; Eiler, J. M.; Stolper, E. M.

2017-03-01

We report the solubility of water in Apollo 15 basaltic "Yellow Glass" and an iron-free basaltic analog composition at 1 atm and 1350 °C. We equilibrated melts in a 1-atm furnace with flowing H2/CO2 gas mixtures that spanned ∼8 orders of magnitude in fO2 (from three orders of magnitude more reducing than the iron-wüstite buffer, IW-3.0, to IW+4.8) and ∼4 orders of magnitude in pH2/pH2O (from 0.003 to 24). Based on Fourier transform infrared spectroscopy (FTIR), our quenched experimental glasses contain 69-425 ppm total water (by weight). Our results demonstrate that under the conditions of our experiments: (1) hydroxyl is the only H-bearing species detected by FTIR; (2) the solubility of water is proportional to the square root of pH2O in the furnace atmosphere and is independent of fO2 and pH2/pH2O; (3) the solubility of water is very similar in both melt compositions; (4) the concentration of H2 in our iron-free experiments is <∼4 ppm, even at oxygen fugacities as low as IW-2.3 and pH2/pH2O as high as 11; (5) Secondary ion mass spectrometry (SIMS) analyses of water in iron-rich glasses equilibrated under variable fO2 conditions may be strongly influenced by matrix effects, even when the concentration of water in the glasses is low; and (6) Our results can be used to constrain the entrapment pressure of lunar melt inclusions and the partial pressures of water and molecular hydrogen in the carrier gas of the lunar pyroclastic glass beads. We find that the most water-rich melt inclusion of Hauri et al. (2011) would be in equilibrium with a vapor with pH2O ∼ 3 bar and pH2 ∼ 8 bar. We constrain the partial pressures of water and molecular hydrogen in the carrier gas of the lunar pyroclastic glass beads to be 0.0005 bar and 0.0011 bar respectively. We calculate that batch degassing of lunar magmas containing initial volatile contents of 1200 ppm H2O (dissolved primarily as hydroxyl) and 4-64 ppm C would produce enough vapor to reach the critical vapor volume fraction thought to be required for magma fragmentation (∼65-75 vol.%) at a total pressure of ∼5 bar (corresponding to a depth beneath the lunar surface of ∼120 m). At a fragmentation pressure of ∼5 bar, the calculated vapor composition is dominated by H2, supporting the hypothesis that H2, rather than CO, was the primary propellant of the lunar fire fountain eruptions. The results of our batch degassing model suggest that initial melt compositions with >∼200 ppm C would be required for the vapor composition to be dominated by CO rather than H2 at 65-75% vesicularity.

Nonlinear partitioning of OH between Ca-rich plagioclase and arc basaltic melt

NASA Astrophysics Data System (ADS)

Hamada, M.; Ushioda, M.; Takahashi, E.

2011-12-01

The hydrogen in nominally anhydrous minerals (NAMs) is becoming a new proxy for dissolved H2O in silicate melts. Plagioclase is one of the NAMs which accommodates hydrogen as OH. Here, we report experimental results on the partitioning of OH between Ca-rich plagioclase and arc basaltic melt. We carried out hydrous melting experiments of arc basaltic magma at 350 MPa using an internally-heated pressure vessel. Starting material was hydrous glass (0.8 wt.%≦H2O≦4.5 wt.%) of an undifferentiated rock from Miyakejima volcano, a frontal-arc volcano in Izu-arc (MTL rock: 50.5% SiO2, 18.1% Al2O3, 4.9% MgO). A grain of Ca-rich plagioclase (≈ 1 mg, about An95, FeOt ≈ 0.5 wt.%) and ≈ 10 mg of powdered glasses were sealed in Au80Pd20 alloy capsule and kept at around the liquidus temperature. Liquidus phase of MTL rock at 350 MPa is always plagioclase with 0 to 4.5 wt.% H2O in melt, and therefore, a grain of plagioclase and hydrous melt are nearly in equilibrium. Oxygen fugacity during the melting experiments was not controlled; the estimated oxygen fugacity was 3 log unit above Ni-NiO buffer. Experiments were quenched after 24-48 hours. Concentrations of H2O in melt and concentration of OH in plagioclase were analyzed by infrared spectroscopy. Obtained correlation between H2O concentration in melt and OH concentration in plagioclase is nonlinear; partition coefficient in molar basis is ≈ 0.01 with low H2O in melt (≤ 1 wt.%), while it decreases down to ≈ 0.005 with increasing H2O in melt (Fig.1). The OH concentration of Ca-rich plagioclase (about An90) from the 1986 summit eruption of Izu-Oshima volcano, also a frontal-arc volcano in Izu arc, shows variation ranging from <50 ppm H2O through 300 ppm H2O as a result of polybaric degassing (Hamada et al. 2011, EPSL 308, 259-266). Melting experiments of hydrous basalts constrained that An90 plagioclase crystallizes form H2O-rich melt (up to 6 wt.% H2O). In consistent with previous studies, our experiments demonstrate that plagioclase with 300 ppm of OH can be in equilibrium with H2O-rich melt dissolving 5-6 wt.% H2O (Fig.1). Plagioclase from the 1986 summit eruption of Izu-Oshima volcano records polybaric degassing history of magma from 5-6 wt.% H2O in melt (300 ppm of OH in plagioclase) to almost dry melt (50 ppm of OH in plagioclase).

Sulfur, Chlorine and Fluorine Degassing and Atmospheric Loading by the Roza eruption, Columbia River Basalt Group, Washington

NASA Technical Reports Server (NTRS)

Thordarson, Th.; Self, S

1996-01-01

In this study we attempt to quantify the amount of S, Cl and F released by the 1300 cu km Roza member (approximately 14.7 Ma) of the Columbia River Basalt Group, which was produced by a moderate-size flood basalt eruption in the mid-Miocene. Our results are the first indication of the potential atmospheric SO2 yield from a flood basalt eruption, and indicate the mechanism by which flood basalt eruptions may have seriously affected the environment. Glass inclusions in phenocrysts and quenched glass in products from various stages of the eruption were analyzed for concentrations of S, Cl and F and major elements. Glass inclusions contain 1965 +/- 110 ppm S, 295 +/- 65 ppm Cl and 1310 +/- 110 ppm F. Groundmass glass of Roza dike selvages contains considerably lower concentrations: 1110 +/- 90 ppm S, 245 +/- 30 ppm Cl and 1020 +/- 25 ppm F. Scoria clasts from near vent deposits contain 665 +/- 75 ppm S, 175 +/- 5 ppm Cl and 950 +/- 20 ppm F, and the groundmass glass of lava selvages contains 520 +/- 30 ppm S, 190 +/- 30 ppm Cl and 890 +/- 55 ppm F. In crystalline lava, the concentrations are 195 ppm S, 100 ppm Cl and 830 ppm F. Volatile element concentrations in these samples represent the progress of degassing through the eruption and can be used to estimate the potential amount of the volatiles S, Cl and F released by the magma into the atmosphere, as well as to evaluate the amount liberated by various phases of the eruption. The total amount of volatiles released by the Roza eruption is estimated to have been approximately 12,420 MtSO2, approximately 710 MtHCI and approximately 1780 MtHF. The Roza magma liberated approximately 9620 MtSO, (77% of the total volatile mass released), approximately 400 MtHCI (56%) and approximately 1450 MtHF (81%) at the vents and lofted by the eruption columns to altitudes of 7-13 km. Degassing of the lava is estimated to have released an additional approximately 2810 MtSO2, approximately 310 MtHCI and approximately 330 MtHF. The Roza eruption is likely to have lasted for approximately 10 years, indicating an annual H2SO4-mass loading of approximately 1800 Mt. Thus, the atmospheric perturbations associated with the Roza eruption may have been of the magnitude predicted for a severe "nuclear" or "volcanic" winter, but lasting up to a decade or more.

Chemical behavior of Cu, Zn, Cd, and Pb in a eutrophic reservoir: speciation and complexation capacity.

PubMed

Tonietto, Alessandra Emanuele; Lombardi, Ana Teresa; Choueri, Rodrigo Brasil; Vieira, Armando Augusto Henriques

2015-10-01

This research aimed at evaluating cadmium (Cd), copper (Cu), lead (Pb), and zinc (Zn) speciation in water samples as well as determining water quality parameters (alkalinity, chlorophyll a, chloride, conductivity, dissolved organic carbon, dissolved oxygen, inorganic carbon, nitrate, pH, total suspended solids, and water temperature) in a eutrophic reservoir. This was performed through calculation of free metal ions using the chemical equilibrium software MINEQL+ 4.61, determination of labile, dissolved, and total metal concentrations via differential pulse anodic stripping voltammetry, and determination of complexed metal by the difference between the total concentration of dissolved and labile metal. Additionally, ligand complexation capacities (CC), such as the strength of the association of metals-ligands (logK'ML) and ligand concentrations (C L) were calculated via Ruzic's linearization method. Water samples were taken in winter and summer, and the results showed that for total and dissolved metals, Zn > Cu > Pb > Cd concentration. In general, higher concentrations of Cu and Zn remained complexed with the dissolved fraction, while Pb was mostly complexed with particulate materials. Chemical equilibrium modeling (MINEQL+) showed that Zn(2+) and Cd(2+) dominated the labile species, while Cu and Pb were complexed with carbonates. Zinc was a unique metal for which a direct relation between dissolved species with labile and complexed forms was obtained. The CC for ligands indicated a higher C L for Cu, followed by Pb, Zn, and Cd in decreasing amounts. Nevertheless, the strength of the association of all metals and their respective ligands was similar. Factor analysis with principal component analysis as the extraction procedure confirmed seasonal effects on water quality parameters and metal speciation. Total, dissolved, and complexed Cu and total, dissolved, complexed, and labile Pb species were all higher in winter, whereas in summer, Zn was mostly present in the complexed form. A high degree of deterioration of the reservoir was confirmed by the results of this study.

Mercury bioaccumulation in cartilaginous fishes from Southern New England coastal waters: Contamination from a trophic ecology and human health perspective

PubMed Central

Taylor, David L.; Kutil, Nicholas J.; Malek, Anna J.; Collie, Jeremy S.

2014-01-01

This study examined total mercury (Hg) concentrations in cartilaginous fishes from Southern New England coastal waters, including smooth dogfish (Mustelus canis), spiny dogfish (Squalus acanthias), little skate (Leucoraja erinacea), and winter skate (L. ocellata). Total Hg in dogfish and skates were positively related to their respective body size and age, indicating Hg bioaccumulation in muscle tissue. There were also significant inter-species differences in Hg levels (mean ± 1 SD, mg Hg/kg dry weight, ppm): smooth dogfish (3.3 ± 2.1 ppm; n = 54) > spiny dogfish (1.1 ± 0.7 ppm; n = 124) > little skate (0.4 ± 0.3 ppm; n = 173) ~ winter skate (0.3 ± 0.2 ppm; n = 148). The increased Hg content of smooth dogfish was attributed to its upper trophic level status, determined by stable nitrogen (δ15N) isotope analysis (mean δ15N = 13.2 ± 0.7‰), and the consumption of high Hg prey, most notably cancer crabs (0.10 ppm). Spiny dogfish had depleted δ15N signatures (11.6 ± 0.8‰), yet demonstrated a moderate level of contamination by foraging on pelagic prey with a range of Hg concentrations, e.g., in order of dietary importance, butterfish (Hg = 0.06 ppm), longfin squid (0.17 ppm), and scup (0.11 ppm). Skates were low trophic level consumers (δ15N = 11.9-12.0‰) and fed mainly on amphipods, small decapods, and polychaetes with low Hg concentrations (0.05-0.09 ppm). Intra-specific Hg concentrations were directly related to δ15N and carbon (δ13C) isotope signatures, suggesting that Hg biomagnifies across successive trophic levels and foraging in the benthic trophic pathway increases Hg exposure. From a human health perspective, 87% of smooth dogfish, 32% of spiny dogfish, and < 2% of skates had Hg concentrations exceeding the US Environmental Protection Agency threshold level (0.3 ppm wet weight). These results indicate that frequent consumption of smooth dogfish and spiny dogfish may adversely affect human health, whereas skates present minimal risk. PMID:25081850

Determination of the content of fatty acid methyl esters (FAME) in biodiesel samples obtained by esterification using 1H-NMR spectroscopy.

PubMed

Mello, Vinicius M; Oliveira, Flavia C C; Fraga, William G; do Nascimento, Claudia J; Suarez, Paulo A Z

2008-11-01

Three different calibration curves based on (1)H-NMR spectroscopy (300 MHz) were used for quantifying the reaction yield during biodiesel synthesis by esterification of fatty acids mixtures and methanol. For this purpose, the integrated intensities of the hydrogens of the ester methoxy group (3.67 ppm) were correlated with the areas related to the various protons of the alkyl chain (olefinic hydrogens: 5.30-5.46 ppm; aliphatic: 2.67-2.78 ppm, 2.30 ppm, 1.96-2.12 ppm, 1.56-1.68 ppm, 1.22-1.42 ppm, 0.98 ppm, and 0.84-0.92 ppm). The first curve was obtained using the peaks relating the olefinic hydrogens, a second with the parafinic protons and the third curve using the integrated intensities of all the hydrogens. A total of 35 samples were examined: 25 samples to build the three different calibration curves and ten samples to serve as external validation samples. The results showed no statistical differences among the three methods, and all presented prediction errors less than 2.45% with a co-efficient of variation (CV) of 4.66%. 2008 John Wiley & Sons, Ltd.

Stormwater chemical contamination caused by cured-in-place pipe (CIPP) infrastructure rehabilitation activities.

PubMed

Tabor, Matthew L; Newman, Derrick; Whelton, Andrew J

2014-09-16

Cured-in-place pipe (CIPP) is becoming a popular U.S. stormwater culvert rehabilitation method. Several State transportation agencies have reported that CIPP activities can release styrene into stormwater, but no other contaminants have been monitored. CIPP's stormwater contamination potential and that of its condensate waste was characterized. Condensate completely dissolved Daphnia magna within 24 h. Condensate pH was 6.2 and its chemical oxygen demand (COD) level was 36,000 ppm. D. magna mortality (100%) occurred in 48 h, even when condensate was diluted by a factor of 10,000 and styrene was present at a magnitude less than its LC50. Condensate and stormwater contained numerous carcinogenic solvents used in resin synthesis, endocrine disrupting contaminants such as plasticizers, and initiator degradation products. For 35 days, COD levels at the culvert outlets and downstream ranged from 100 to 375 ppm and styrene was 0.01 to 7.4 ppm. Although contaminant levels generally reduced with time, styrene levels were greatest 50 ft downstream, not at the culvert outlet. Cured CIPP extraction tests confirmed that numerous contaminants other than styrene were released into the environment and their persistence and toxicity should be investigated. More effective contaminant containment and cleaner installation processes must be developed to protect the environment.

Uranium hydrogeochemical and stream sediment reconnaissance of the Durango NTMS quadrangle, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dawson, H.E.; Weaver, T.A.

1979-01-01

During the spring and summer of 1976, 1518 water and 1604 waterborne sediment samples were collected from 1804 locations in the Durango NTMS quadrangle, Colorado. The samples obtained from this 19 940-km/sup 2/ area were analyzed at the Los Alamos Scientific Laboratory for total uranium. The uranium concentrations in waters ranged from less than the detectable limit of 0.2 ppB to 25.7 ppB, with a mean value of 0.84 ppB. The concentrations in sediments ranged from 1.0 ppM to 71.6 ppM, with a mean value of 4.2 ppM. Study of total water and total sediment populations indicated that both aremore » actually mixtures of several populations. Consequently, samples were chosen for discussion on the basis of their having conspicuously high uranium concentrations relative to surrounding background values. Thirty-four water samples (approximately 2.2% of the total water population) had uranium concentrations above 5.00 ppB, the highest of which were well water samples from the San Luis Valley. Thirty-seven sediment samples (approximately 2.3% of the total sediment population) had uranium concentrations above 12.0 ppM. The majority of these were taken from sites in Precambrian rocks, but several came from Paleozoic and Mesozoic strate and Tertiary volcanics. The uranium concentrations in sediment samples from areas of Precambrian rock were especially high and these areas may warrant further, more detailed investigations.« less

Nucleation and Growth of Anodic Electrocrystallized Products on Ship Hull Zinc in Salt Water Solutions

DTIC Science & Technology

1975-12-01

EO02 oxygen potential E62 standard oxygen potential a1 hydroxide ion activity ; i 15 emf electromo tive force 4FeSi iron silicide PPM parts per...indicated, references to water shall be understood to mean reagent water conforming to ASTM Specification D 1193, for Reagent Water. 3.3 Sodium ...Ocean Water 4.1 Dissolve 245.34g of sodium chloride (NaCl) and 40.94g of anhydrous sodium sulfate (Na2SO4) in 8 to 9 liters 4 of water. Add slowly

Evaluation of Physicochemical Properties of South African Cashew Apple Juice as a Biofuel Feedstock

PubMed Central

Deenanath, Evanie Devi; Daramola, Michael; Falcon, Rosemary; Iyuke, Sunny

2015-01-01

Cashew apple juice (CAJ) is one of the feedstocks used for biofuel production and ethanol yield depends on the physical and chemical properties of the extracted juice. As far as can be ascertained, information on physical and chemical properties of South African cashew apple juice is limited in open literature. Therefore, this study provides information on the physical and chemical properties of the South African cashew apple juice. Physicochemical characteristics of the juice, such as specific gravity, pH, sugars, condensed tannins, Vitamin C, minerals, and total protein, were measured from a mixed variety of cashew apples. Analytical results showed the CAJ possesses specific gravity and pH of 1.050 and 4.52, respectively. The highest sugars were glucose (40.56 gL−1) and fructose (57.06 gL−1). Other chemical compositions of the juice were condensed tannin (55.34 mgL−1), Vitamin C (112 mg/100 mL), and total protein (1.78 gL−1). The minerals content was as follows: zinc (1.39 ppm), copper (2.18 ppm), magnesium (4.32 ppm), iron (1.32 ppm), sodium (5.44 ppm), and manganese (1.24 ppm). With these findings, South African CAJ is a suitable biomass feedstock for ethanol production. PMID:26345160

21 CFR 556.495 - Oxfendazole.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., FEEDS, AND RELATED PRODUCTS TOLERANCES FOR RESIDUES OF NEW ANIMAL DRUGS IN FOOD Specific Tolerances for Residues of New Animal Drugs § 556.495 Oxfendazole. Cattle: A tolerance is established for total... (ppm) fenbendazole in the target liver tissue. A fenbendazole concentration of 0.8 ppm in liver...

21 CFR 556.495 - Oxfendazole.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., FEEDS, AND RELATED PRODUCTS TOLERANCES FOR RESIDUES OF NEW ANIMAL DRUGS IN FOOD Specific Tolerances for Residues of New Animal Drugs § 556.495 Oxfendazole. Cattle: A tolerance is established for total... (ppm) fenbendazole in the target liver tissue. A fenbendazole concentration of 0.8 ppm in liver...

21 CFR 556.495 - Oxfendazole.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., FEEDS, AND RELATED PRODUCTS TOLERANCES FOR RESIDUES OF NEW ANIMAL DRUGS IN FOOD Specific Tolerances for Residues of New Animal Drugs § 556.495 Oxfendazole. Cattle: A tolerance is established for total... (ppm) fenbendazole in the target liver tissue. A fenbendazole concentration of 0.8 ppm in liver...

21 CFR 556.495 - Oxfendazole.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., FEEDS, AND RELATED PRODUCTS TOLERANCES FOR RESIDUES OF NEW ANIMAL DRUGS IN FOOD Specific Tolerances for Residues of New Animal Drugs § 556.495 Oxfendazole. Cattle: A tolerance is established for total... (ppm) fenbendazole in the target liver tissue. A fenbendazole concentration of 0.8 ppm in liver...

21 CFR 556.495 - Oxfendazole.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., FEEDS, AND RELATED PRODUCTS TOLERANCES FOR RESIDUES OF NEW ANIMAL DRUGS IN FOOD Specific Tolerances for Residues of New Animal Drugs § 556.495 Oxfendazole. Cattle: A tolerance is established for total... (ppm) fenbendazole in the target liver tissue. A fenbendazole concentration of 0.8 ppm in liver...

Comparative study on conventional, ultrasonication and microwave assisted extraction of γ-oryzanol from rice bran.

PubMed

Kumar, Pramod; Yadav, Devbrat; Kumar, Pradyuman; Panesar, Paramjeet Singh; Bunkar, Durga Shankar; Mishra, Diwaker; Chopra, H K

2016-04-01

In present study, conventional, ultrasonic and microwave assisted extraction methods were compared with the aim of optimizing best fitting solvent and method, solvent concentration and digestion time for high yield of γ-oryzanol from rice bran. Petroleum ether, hexane and methanol were used to prepare extracts. Extraction yield were evaluated for giving high crude oil yield, total phenolic content (TPC) and γ-oryzanol content. Gas chromatography-mass spectrophotometry was used for the determination of γ-oryzanol concentration. The highest concentration of γ-oryzanol was detected in methanolic extracts of microwave treatment (85.0 ppm) followed by ultrasonication (82.0 ppm) and conventional extraction method (73.5 ppm). Concentration of γ-oryzanol present in the extracts was found to be directly proportional to the total phenolic content. A combination of 80 % methanolic concentration and 55 minutes digestion time of microwave treatment yielded the best extraction method for TPC and thus γ-oryzanol (105 ppm).

Spatial variability of total dissolved copper and copper speciation in the inshore waters of Bermuda.

PubMed

Oldham, V E; Swenson, M M; Buck, K N

2014-02-15

Total dissolved copper (Cu) and Cu speciation were examined from inshore waters of Bermuda, in October 2009 and July-August 2010, to determine the relationship between total dissolved Cu, Cu-binding ligands and bioavailable, free, hydrated Cu(2+) concentrations. Speciation was performed using competitive ligand exchange-adsorptive cathodic stripping voltammetry (CLE-ACSV). Mean total dissolved Cu concentrations ranged from 1.4 nM to 19.2 nM, with lowest concentrations at sites further from shore, consistent with previous measurements in the Sargasso Sea, and localized Cu enrichment inshore in enclosed harbors. Ligand concentrations exceeded dissolved [Cu] at most sites, and [Cu(2+)] were correspondingly low at those sites, typically <10(-13) M. One site, Hamilton Harbour, was found to have [Cu] in excess of ligands, resulting in [Cu(2+)] of 10(-10.7) M, and indicating that Cu may be toxic to phytoplankton here. Copyright © 2013 Elsevier Ltd. All rights reserved.

Function of peatland located on secondary transformed peat-moorsh soils on groundwater purification processes and the elution of soil organic matter

NASA Astrophysics Data System (ADS)

Szczepański, M.; Szajdak, L.; Bogacz, A.

2009-04-01

The investigation of peatland is used to show the water quality functioning with respect to different forms of nitrogen and carbon. The purification of ground water by the transect of 4.5 km long consisting organic soils (peat-moorsh soils) was estimated. This transect is located in the Agroecological Landscape Park in Turew, 40 km South-West of Poznan, West Polish Lowland. There is this transect along Wyskoć ditch. pH, the contents of total and dissolved organic carbon, total nitrogen, N-NO3-, N-NH4+ was measured. Additionally C/N factors of peats were estimated. The investigation has shown the impact of the peatland located on the secondary transformed peat - moorsh soils on the lowering of total nitrogen, ammonium, and nitrates as well as total and dissolved organic carbon in ground water. Peat-moorsh soils were described and classified according to Polish hydrogenic soil classification and World Reference Base Soil Notation. There are these investigated points along to Wyskoc ditch. Two times a month during entire vegetation season the following material was taken from four chosen sites marked as Zbechy, Bridge, Shelterbelt and Hirudo: samples of peat, from the depth of 0-20 cm, samples of water from the ditch, samples of ground water from wells established for this investigation. Samples of peat-moorsh soils were collected at the depth 0-20 cm. Soils were sampled two times a month from 10 sites of each site. Samples were air dried and crushed to pass a 1 mm-mesh sieve. These 10 sub-samples were mixed for the reason of preparing a "mean sample", which used for the determination of pH (in 1M KCl), dissolved organic carbon (DOC), total organic carbon (TOC), total nitrogen (Ntotal), and N-NO3- as well as N-NH4+. In water from Wyskoć ditch pH, Ntotal, N-NO3-, N-NH4+, DTC (dissolved total carbon) and DOC (dissolved organic carbon) was measured. Ground water samples were collected from four wells established for this investigation. The water was filtered by the middle velocity separation and pH, N-total, N-NO3-, N-NH4+, DTC (dissolved total carbon) and DOC (dissolved organic carbon) ware measured. Peatland located on the secondary transformed peat - moorsh soils has revealed the lowering in ground water: nitrates 38.5%, N-organic 10%, N-total 24.5%, ammonium 38.7%, dissolved total carbon 33.1%, dissolved total inorganic carbon 10%, and dissolved organic carbon 57.5%. The dissolution of soil organic matter from peat-moorsh soils in broad range of pH and ionic strength was investigated. The rates of the reaction were calculated from the kinetics of first order reaction model. The investigations have shown the impact of the properties of secondary transformed peat-moorsh soils on the rates of the dissolution of organic matter.

Tracing Acetylene Dissolved in Transformer Oil by Tunable Diode Laser Absorption Spectrum.

PubMed

Ma, Guo-Ming; Zhao, Shu-Jing; Jiang, Jun; Song, Hong-Tu; Li, Cheng-Rong; Luo, Ying-Ting; Wu, Hao

2017-11-02

Dissolved gas analysis (DGA) is widely used in monitoring and diagnosing of power transformer, since the insulation material in the power transformer decomposes gases under abnormal operation condition. Among the gases, acetylene, as a symbol of low energy spark discharge and high energy electrical faults (arc discharge) of power transformer, is an important monitoring parameter. The current gas detection method used by the online DGA equipment suffers from problems such as cross sensitivity, electromagnetic compatibility and reliability. In this paper, an optical gas detection system based on TDLAS technology is proposed to detect acetylene dissolved in transformer oil. We selected a 1530.370 nm laser in the near infrared wavelength range to correspond to the absorption peak of acetylene, while using the wavelength modulation strategy and Herriott cell to improve the detection precision. Results show that the limit of detection reaches 0.49 ppm. The detection system responds quickly to changes of gas concentration and is easily to maintenance while has no electromagnetic interference, cross-sensitivity, or carrier gas. In addition, a complete detection process of the system takes only 8 minutes, implying a practical prospect of online monitoring technology.

40 CFR 122.45 - Calculating NPDES permit conditions (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2013 CFR

2013-07-01

... specifies the limitation for the metal in the dissolved or valent or total form; or (2) In establishing... the metal in the dissolved or valent or total form to carry out the provisions of the CWA; or (3) All approved analytical methods for the metal inherently measure only its dissolved form (e.g., hexavalent...

40 CFR 122.45 - Calculating NPDES permit conditions (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2012 CFR

2012-07-01

... specifies the limitation for the metal in the dissolved or valent or total form; or (2) In establishing... the metal in the dissolved or valent or total form to carry out the provisions of the CWA; or (3) All approved analytical methods for the metal inherently measure only its dissolved form (e.g., hexavalent...

Total lead concentration in new decorative enamel paints in Lebanon, Paraguay and Russia.

PubMed

Clark, C Scott; Speranskaya, Olga; Brosche, Sara; Gonzalez, Hebe; Solis, Daniela; Kodeih, Naji; Roda, Sandy; Lind, Caroline

2015-04-01

Lead concentrations in new enamel decorative paints were determined in three countries in different areas of the world where data were not previously available. The average total lead concentration of the enamel decorative paints purchased in Lebanon, Paraguay and Russia was 24,500ppm (ppm, dry weight), more than 270 times the current limit of 90ppm in Canada and in the United States. Sixty-three percent of these paints contained concentrations greater than 90ppm. Fifty-nine percent contained concentrations greater than 600ppm, the current limit in some countries. The maximum concentrations found were 236,000ppm in Lebanon, 169,000ppm in Paraguay and 52,900ppm in Russia. An average of 29% of the samples contained exceedingly high lead concentrations, >=10,000ppm. Five brands of paint were sampled in each of Lebanon and Paraguay and seven in Russia. Three colors from each brand were analyzed. For five of the six samples of the two brands in Lebanon with affiliations outside the country, the lead concentrations ranged from 1360ppm to 135,000ppm. In Lebanon the maximum concentration in the Egypt-affiliated brand (Sipes) was 135,000ppm and the maximum for the USA-affiliated brand (Dutch Boy) was 32,400ppm. Lead was not detected in any paints from the three of the four brands of paint purchased in Paraguay that had headquarters/affiliations in other countries (Brazil-Coralit), Germany (Suvinil) and USA (Novacor)). Two of the three paints from each of the other Paraguay brands contained high levels of lead with the maximum concentrations of 108,000 and 168,000ppm; one of these brands was manufactured under a license from ICI in the Netherlands. All of the paints purchased in Russia were from Russian brands and were manufactured in Russia. All three paints from one brand contained below detection levels of lead. The maximum levels of lead in the other six brands in Russia ranged from 3230 to 52,900ppm. The two brands with the highest lead concentration, TEKS and LAKRA, were produced by companies in the top three in market share.. Overall, lead concentrations were much higher in the colored paints such as red and yellow than in white paints. In each of the three countries a brand based in that country had a colored paint that either met a 90ppm limit or was close to meeting the limit-demonstrating that practical technology was available in each of these countries to produce low lead bright colored enamel decorative paints. Even though technology for producing paint without added lead existed in each of these countries, twenty-nine (29) percent of the paints analyzed contained exceedingly high concentrations (>=10,000ppm) of lead. Copyright © 2015 Elsevier Inc. All rights reserved.

Reprint of Ecological health status of the Lagos wetland ecosystems: Implications for coastal risk reduction

NASA Astrophysics Data System (ADS)

Agboola, Julius I.; Ndimele, Prince E.; Odunuga, Shakirudeen; Akanni, Adeniran; Kosemani, Bosede; Ahove, Michael A.

2016-12-01

Lagos, a major urban agglomeration in the world is characterized by wetlands and basin for upstream rivers such as Ogun, Oshun and Yewa Rivers. Ongoing environmental pressures exerted by large-scale land reclamation for residential quarters, refuse and sewage dumping, and other uses, however, are suspected to have had a substantial impact on ecological health of the Lagos wetland ecosystems over the last few decades. To determine the impact of these pressures, we examined spatial changes in three wetlands areas- Badore/Langbasa (BL), Festac/Iba/Ijegun (FI) and Ologe/Otto-Awori (OO) through field sample collection and analyses of surface water, sediments, air-water interface gas fluxes and vegetations. Surface water conductivity, total suspended solids (TSS), alkalinity, chloride, biological oxygen demand (BOD), nitrate, phosphate and heavy metals (Zn, Cu, Fe, Na, Mn, Pb, Cd, K and Ni) exhibited relative spatial stability while other water quality parameters varied significantly (P < 0.05) across the wetland areas. Also, dissolved inorganic carbon (DIC) contributed to most of the total dissolved solids (TDS) since only DIC correlated significantly with TDS (r = 0.889; P = 0.05, n = 12) and TS (r = 0.891; P = 0.05, n = 12), suggesting a strong capacity for carbon sequestration and carbon sink across the wetland areas. None of the encountered vegetation species are in the vulnerable category of the International Union for Conservation of Nature (IUCN). There are indications of steady rise in greenhouse gas levels in Lagos since air CO2 value at BL have reached global threshold of 400 ppm with OO and FI closely approaching. We conclude that the Lagos wetland ecosystems, especially OO and FI still have some semblance of natural habitat. However, further destruction and unwise use of the resources could cause damage to physical, chemical, geological and biological processes in nature, which could result to grave socio-economic and cultural consequences to the local communities whose livelihood and lifestyle depend on these valued wetlands.

Ecological health status of the Lagos wetland ecosystems: Implications for coastal risk reduction

NASA Astrophysics Data System (ADS)

Agboola, Julius I.; Ndimele, Prince E.; Odunuga, Shakirudeen; Akanni, Adeniran; Kosemani, Bosede; Ahove, Michael A.

2016-12-01

Lagos, a major urban agglomeration in the world is characterized by wetlands and basin for upstream rivers such as Ogun, Oshun and Yewa Rivers. Ongoing environmental pressures exerted by large-scale land reclamation for residential quarters, refuse and sewage dumping, and other uses, however, are suspected to have had a substantial impact on ecological health of the Lagos wetland ecosystems over the last few decades. To determine the impact of these pressures, we examined spatial changes in three wetlands areas- Badore/Langbasa (BL), Festac/Iba/Ijegun (FI) and Ologe/Otto-Awori (OO) through field sample collection and analyses of surface water, sediments, air-water interface gas fluxes and vegetations. Surface water conductivity, total suspended solids (TSS), alkalinity, chloride, biological oxygen demand (BOD), nitrate, phosphate and heavy metals (Zn, Cu, Fe, Na, Mn, Pb, Cd, K and Ni) exhibited relative spatial stability while other water quality parameters varied significantly (P < 0.05) across the wetland areas. Also, dissolved inorganic carbon (DIC) contributed to most of the total dissolved solids (TDS) since only DIC correlated significantly with TDS (r = 0.889; P = 0.05, n = 12) and TS (r = 0.891; P = 0.05, n = 12), suggesting a strong capacity for carbon sequestration and carbon sink across the wetland areas. None of the encountered vegetation species are in the vulnerable category of the International Union for Conservation of Nature (IUCN). There are indications of steady rise in greenhouse gas levels in Lagos since air CO2 value at BL have reached global threshold of 400 ppm with OO and FI closely approaching. We conclude that the Lagos wetland ecosystems, especially OO and FI still have some semblance of natural habitat. However, further destruction and unwise use of the resources could cause damage to physical, chemical, geological and biological processes in nature, which could result to grave socio-economic and cultural consequences to the local communities whose livelihood and lifestyle depend on these valued wetlands.

Mound Spring Complexes in Central Australia: An Analog for Martian Groundwater Fed Outflow Channels?

NASA Technical Reports Server (NTRS)

Clarke, J. D. A.; Stoker, C.

2003-01-01

The arid inland of Australia contains a diversity of landscapes and landscape processes, often of great antiquity, extending back to the Mesozoic and Paleozoic. The potential of this landscape as a source of Mars analogs has, however, been little explored. The few examples studied so far include radiation-tolerant microbes in thermal springs and hematite-silica hydrothermal alteration near Arkaroola in the Finders Ranges, and aeolian landforms at Gurra Gurra water hole the north east of Arkaroola. Further Australian Mars analog studies were provided by the studies of Bourke and Zimbelman of the paleoflood record of the Todd and Hale Rivers in central Australia. To facilitate study of such analogues, Mars Society Australia has embarked on a project to construct a Mars Analog Research Station near Arkaroola. The international scientific community will soon have the opportunity to participate in Mars analog studies in central Australia utilizing this facility. An area of considerable Mars analog potential is the mound spring complexes that occur at the margins of the Great Artesian Basin (GAB) which underlies 22% of the Australian continent and covers 1.7 million km2. The mound springs are formed when ground water flows to a topographic low, and subsurface strata dips up causing a hydrological head at the surface. Minerals precipitated at the spring discharge zone form low mesas or "mounds", the height of which are controlled by the hydrological head. This paper describes the Dalhousie Mound Spring Complex (DMC) in the northern part of South Australia (Figure 1), and its potential as a Mars analog. Hydrogeology: The DMC consists of a cluster of more than 60 active springs formed by natural discharge from the GAB). Total measured discharge from the GAB is 1.74 GL per day, estimated unfocussed natural leakage through the aquaclude is thought be approximately equal to this figure. Some 54 ML per day are currently discharged by the DMC, 3% of the measured total. The discharged artesian waters are of low to moderate salinity (700 - 9400 ppm), near neutral pH (6.8-7.3) and warm (20-46 C). The elevated temperatures are due to passage of the groundwater through deeply buried (up to 3 km) aquifers in an region of high heat flow, rather than magmatic heating. The waters also contain high levels of dissolved iron and H2S and less than 1 ppm dissolved oxygen. The water is carried in the Late Jurassic Algebuckina Sandstone beneath the aquaclude of the Bulldog Shale. It is brought near the surface by the mid-Cenozoic Dalhousie anticline and the ground water flow focused along a series of faults that breach the anticline's crest.

Water requirements of the rayon- and acetate-fiber industry

USGS Publications Warehouse

Mussey, Orville Durey

1957-01-01

Water is required for several purposes in the manufacture of rayon and acetate fiber. These water requirements, as indicated by a survey of the water used by the plants operating in 1953, are both quantitative and qualitative. About 300 mgd (million gallons per day) of water was used in 1953 in the preparation of purified wood cellulose and cotton linters, the basic material from which the rayon and acetate fiber is made. An additional 620 mgd was used in the process of converting the cellulose to rayon and acetate fiber. The total, 920 mgd, is about 1 percent of the total estimated withdrawals of industrial water in the United States in 1953. The rayon- and acetate-fiber plants are scattered through eastern United States and generally are located in small towns or rural areas where there are abundant supplies of clean, soft water. Water use at a typical rayon-fiber plant was about 9 mgd, and at a typical acetate-fiber plant about 38 mgd. About 110 gallons of water was used to produce a pound of rayon fiber 32 gallons per pound was process water and the remainder was used largely for cooling in connection with power production and air conditioning. For the manufacture of a pound of acetate fiber about 170 gallons of water was used. However, the field survey on which this report is based indicated a wide range in the amount of water used per pound of product. For example, in the manufacture of viscose rayon, the maximum unit water use was 8 times the minimum unit water use. Water use in summer was about 22 percent greater than average annual use. About 8 mgd of water was consumed by evaporation in the manufacture of rayon and acetate fiber. More than 90 percent of the water used by the rayon and acetate industry was withdrawn from surface-water sources, about 8 percent from ground water, and less than 2 percent from municipal water supplies. All available analyses of the untreated waters used by the rayon and acetate industry were collected and studied. The untreated waters were generally cool, low in content of calcium and magnesium, and very low in iron and manganese. At many plants, water was obtained from more than one source, and thus had different quality characteristics. Dissolved solids in all the untreated waters analyzed ranged between 14 and 747 ppm (parts per million) but in those waters used in processing the dissolved solids content was less than 200 ppm. The cooling water used by the industry is also generally of very high quality, principally because the requirements for a high-quality process water necessitate location of the plants in areas where such water is available.

Leaky Gut and Mycotoxins: Aflatoxin B1 Does Not Increase Gut Permeability in Broiler Chickens.

PubMed

Galarza-Seeber, Rosario; Latorre, Juan D; Bielke, Lisa R; Kuttappan, Vivek A; Wolfenden, Amanda D; Hernandez-Velasco, Xochitl; Merino-Guzman, Ruben; Vicente, Jose L; Donoghue, Annie; Cross, David; Hargis, Billy M; Tellez, Guillermo

2016-01-01

Previous studies conducted in our laboratory have demonstrated that intestinal barrier function can be adversely affected by diet ingredients or feed restriction, resulting in increased intestinal inflammation-associated permeability. Two experiments were conducted in broilers to evaluate the effect of three concentrations of Aflatoxin B1 (AFB1; 2, 1.5, or 1 ppm) on gastrointestinal leakage and liver bacterial translocation (BT). In experiment 1, 240 day-of-hatch male broilers were allocated in two groups, each group had six replicates of 20 chickens (n = 120/group): Control feed or feed + 2 ppm AFB1. In experiment 2, 240 day-of-hatch male broilers were allocated in three groups, each group had five replicates of 16 chickens (n = 80/group): Control feed; feed + 1 ppm AFB1; or feed + 1.5 ppm AFB1. In both experiments, chickens were fed starter (days 1-7) and grower diets (days 8-21) ad libitum and performance parameters were evaluated every week. At day 21, all chicks received an oral gavage dose of FITC-d (4.16 mg/kg) 2.5 h before collecting blood samples to evaluate gastrointestinal leakage of FITC-d. In experiment 2, a hematologic analysis was also performed. Liver sections were aseptically collected and cultured using TSA plates to determine BT. Cecal contents were collected to determine total colony-forming units per gram of Gram-negative bacteria, lactic acid bacteria (LAB), or anaerobes by plating on selective media. In experiment 2, liver, spleen, and bursa of Fabricius were removed to determine organ weight ratio, and also intestinal samples were obtained for morphometric analysis. Performance parameters, organ weight ratio, and morphometric measurements were significantly different between Control and AFB1 groups in both experiments. Gut leakage of FITC-d was not affected by the three concentrations of AFB1 evaluated (P > 0.05). Interestingly, a significant reduction in BT was observed in chickens that received 2 and 1 ppm AFB1. An increase (P < 0.05) in total aerobic bacteria, total Gram negatives, and total LAB were observed in chickens fed with 2 and 1.5 ppm of AFB1 when compared with Control and 1 ppm chickens. The integrity of gut epithelial barrier was not compromised after exposure to the mycotoxin.

Tracing organic carbon processes in a shallow coastal sandy aquifer

NASA Astrophysics Data System (ADS)

Meredith, K.; Andersen, M. S.; Baker, A.; O'Carrol, D. M.; Bryan, E.; Zainuddin, N. S.; Rutlidge, H.; McDonough, L.

2017-12-01

Coastal groundwater resources are likely to be impacted by climate change due to changes in recharge patterns, surface water flow and sea-level rise, which all have the potential to change how carbon is transported and stored within a catchment. Large quantities of carbon are currently stored within coastal wetland systems, so understanding carbon dynamics is important for climate change predictions into the future. Furthermore, dissolved organic carbon (DOC) can play a major role in weathering processes and deterioration of water quality, therefore understanding the sources, degradation pathways and its reactivity is important. Groundwater samples were collected from five nested sites (15 wells) from a shallow (0-20m) coastal sandy aquifer system located at Anna Bay, New South Wales, Australia. Surface water samples were also collected from the adjacent wetland. Waters were measured for major ion chemistry, carbon isotopes (δ13CDIC, δ13CDOC and 14CDIC) and tritium (3H). The dissolved organic matter (DOM) character was determined using optical spectroscopy and liquid chromatography. DOC was found to be elevated in the wetland (18 ppm) and had the lowest δ13CDOC value (-30.3 ‰). The shallow (3.5 m) groundwater located closest to but downgradient of the wetland (5 m) had similar characteristics to the wetland sample but contained significantly lower DOC concentrations (5 ppm) and were 1 ‰ more enriched in δ13CDOC values. This suggests that the aquifer is a sink for organic matter and the process fractionates the carbon isotopes. Higher resolution studies are underway to characterise and constrain timescales for the DOC transformation processes.

Heavy metals in urban soils of East St. Louis, IL, Part I: Total concentration of heavy metals in soils.

PubMed

Kaminski, M D; Landsberger, S

2000-09-01

The city of East St. Louis, IL, has a history of abundant industrial activities including smelters of ferrous and non-ferrous metals, a coal-fired power plant, companies that produce organic and inorganic chemicals, and petroleum refineries. A protocol for soil analysis was developed to produce sufficient information on the extent of heavy metal contamination in East St. Louis soils. Soil cores representing every borough of East St. Louis were analyzed for heavy metals--As, Cd, Cu, Cr, Hg, Ni, Pb, Sb, Sn, and Zn. The topsoil contained heavy metal concentrations as high as 12.5 ppm Cd, 14,400 ppm Cu, ppm quantities of Hg, 1860 ppm Pb, 40 ppm Sb, 1130 ppm Sn, and 10,360 ppm Zn. Concentrations of Sb, Cu, and Cd were well correlated with Zn concentrations, suggesting a similar primary industrial source. In a sandy loam soil from a vacated rail depot near the bank of the Mississippi River, the metals were evenly distributed down to a 38-cm depth. The clay soils within a half-mile downwind of the Zn smelter and Cu products company contained elevated Cd (81 ppm), Cu (340 ppm), Pb (700 ppm), and Zn (6000 ppm) and displayed a systematic drop in concentration of these metals with depth. This study demonstrates the often high concentration of heavy metals heterogeneously distributed in the soil and provides baseline data for continuing studies of heavy metal soil leachability.

Uranium isotope composition of a laterite profile during extreme weathering of basalt in Guangdong, South China

NASA Astrophysics Data System (ADS)

Huang, J.; Zhou, Z.; Gong, Y.; Lundstrom, C.; Huang, F.

2015-12-01

Rock weathering and soil formation in the critical zone are important for material cycle from the solid Earth to superficial system. Laterite is a major type of soil in South China forming at hot-humid climate, which has strong effect on the global uranium cycle. Uranium is closely related to the environmental redox condition because U is stable at U(Ⅳ) in anoxic condition and U(Ⅵ) as soluble uranyl ion (UO22+) under oxic circumstance. In order to understand the behavior of U isotopes during crust weathering, here we report uranium isotopic compositions of soil and base rock samples from a laterite profile originated from extreme weathering of basalt in Guangdong, South China. The uranium isotopic data were measured on a Nu Plasma MC-ICP-MS at the University of Illinois at Urbana-Champaign using the double spike method. The δ238U of BCR-1 is -0.29±0.03‰ (relative to the international standard CRM-112A), corresponding to a 238U/235U ratio of 137.911±0.004. Our result of BCR-1 agrees with previous analyses (e.g., -0.28‰ in Weyer et al. 2008) [1]. U contents of the laterite profile decrease from 1.9 ppm to 0.9 ppm with depth, and peak at 160 - 170 cm (2.3 ppm), much higher than the U content of base rocks (~0.5 ppm). In contrary, U/Th of laterites is lower than that of base rock (0.27) except the peak at the depth of 160-170 cm (0.38), indicating significant U loss during weathering. Notably, U isotope compositions of soils show a small variation from -0.38 to -0.28‰, consistent with the base rock within analytical error (0.05‰ to 0.08‰, 2sd). Such small variation can be explained by a "rind effect" (Wang et al., 2015) [2], by which U(Ⅳ) can be completely oxidized to U(VI) layer by layer during basalt weathering by dissolved oxygen. Therefore, our study indicates that U loss during basalt weathering at the hot-humid climate does not change U isotope composition of superficial water system. [1] Weyer S. et al. (2008) Natural fractionation of 238U/235U. GCA 72,345-359 [2] Wang X. et al. (2015) Isotope fractionation during oxidation of tetravalent uranium by dissolved oxygen. GCA 150, 160-170

DIEL FLUX OF DISSOLVED CARBOHYDRATE IN A SALT MARSH AND A SIMULATED ESTUARINE ECOSYSTEM

EPA Science Inventory

The concentrations of total dissolved carbohydrate (TCHO), monosaccharide (MCHO) and polysaccharide (PCHO) were followed over a total of ten diel cycles in a salt marsh and a 13 cu m seawater tank simulating an estuarine ecosystem. Their patterns are compared to those for total d...

Economic evaluation of public-private mix for tuberculosis care and control, India. Part II. Cost and cost-effectiveness.

PubMed

Pantoja, A; Lönnroth, K; Lal, S S; Chauhan, L S; Uplekar, M; Padma, M R; Unnikrishnan, K P; Rajesh, J; Kumar, P; Sahu, S; Wares, F; Floyd, K

2009-06-01

Bangalore City, India. To assess the cost and cost-effectiveness of public-private mix (PPM) for tuberculosis (TB) care and control when implemented on a large scale. DOTS implementation under the Revised National TB Control Programme (RNTCP) began in 1999, PPM was introduced in mid-2001 and a second phase of intensified PPM began in 2003. Data on the costs and effects of TB treatment from 1999 to 2005 were collected and used to compare the two distinct phases of PPM with a scenario of no PPM. Costs were assessed in 2005 $US for public and private providers, patients and patient attendants. Sources of data included expenditure records, medical records, interviews with staff and patient surveys. Effectiveness was measured as the number of cases successfully treated. When PPM was implemented, total provider costs increased in proportion to the number of successfully treated TB cases. The average cost per patient treated from the provider perspective when PPM was implemented was stable, at US$69, in the intensified phase compared with US$71 pre-PPM. PPM resulted in the shift of an estimated 7200 patients from non-DOTS to DOTS treatment over 5 years. PPM implementation substantially reduced costs to patients, such that the average societal cost per patient successfully treated fell from US$154 to US$132 in the 4 years following the initiation of PPM. Implementation of PPM on a large scale in an urban setting can be cost-effective, and considerably reduces the financial burden of TB for patients.

In-Situ Cosmogenic 36Cl Production Rate Calibration from Basaltic Flows of Mount Etna (Sicily, 38° N)

NASA Astrophysics Data System (ADS)

Schimmelpfennig, I.; Benedetti, L.; Pik, R.; Burnard, P.; Blard, P. H.; Bourles, D.

2007-12-01

One of the CRONUS-EU goals is to provide high quality calibration sites from independently dated surfaces. Several previous studies have been conducted on 36Cl production rate calibration (e.g. Stone et al. 1996, Phillips et al. 2001), which, however, used different protocols and yielded 36Cl production rates with up to 40% discrepancies. The objectives of this study are 1- to understand the source of these discrepancies and 2- to calibrate 36Cl production rates from its target elements Ca and K. As a first step we focused on testing the chemical protocol by performing a sequential 36Cl extraction experiment on whole rock grains and Ca-rich plagioclase from the same sample. The sample was collected at Mt. Etna on a pahoehoe flow, which has a K-Ar fossil exposure time of (10±3) kyr. Cosmogenic 3He was also precisely measured within cogenetic olivine phenocrysts of this sample (Blard et al. 2005) and yields an exposure time of (10.4±1.5) kyr. Both, total Cl and 36Cl concentrations from the first dissolution steps are high, 5800 ppm (whole rock) and 450 ppm (plagioclase) Cl, and 107 - 106 atoms 36Cl/g of rock dissolved. After about 20% dissolution of the plagioclase sample, Cl is almost completely removed (1-3ppm) and 36Cl concentrations reach a plateau value of 2*105 atoms/g of rock. Using the Stone et al. (1996) and Evans et al. (1997) 36Cl production rates for the target elements Ca and K, respectively, this plateau concentration yields an exposure age which is in excellent agreement with K-Ar dating and cosmogenic 3He ages. On the contrary, in the whole rock sample total Cl concentrations remain high (>330ppm) resulting in a considerable 36Cl production from capture of low-energy neutrons by 35Cl, an additional and still not well-constrained 36Cl production mechanism. The resulting exposure ages from the whole rock are 35-45% higher than the independent 3He ages. For 36Cl production rate calibration from Ca, we will use separated Ca-rich plagioclase from various Mt. Etna lava flows of different elevation and independently determined ages between 400 yr and 41 kyr. To better constrain the 36Cl production rate from K, separated sanidine (K-rich feldspar) from a 15 kyr old lava flow of volcano Payun-Matru (Argentina, 36° S) will be used. Stone J.O., et al. (1996), Geochim. Cosmochim. Acta 60 679-692; Phillips F.M., et al. (2001), Chem. Geol. 175 689-701; Blard P.H., et al. (2005), EPSL 236 613-631; Evans J.M. et al. (1997), Nucl. Instr. and Meth. in Phys. Res. B 123 334-340

Determination of PCBs in fish using enzyme-linked immunosorbent assay (ELISA)

USGS Publications Warehouse

Lasrado, J.A.; Santerre, C.R.; Zajicek, J.L.; Stahl, J.R.; Tillitt, D.E.; Deardorff, D.

2003-01-01

Polychlorinated biphenyls (PCBs) were determined in fish tissue using an enzyme-linked immunosorbent assay (ELISA). Standard curves for Aroclor 1248, 1254, and 1260 in catfish tissue were developed with ranges from 0.05 to 0.5 ppm and 0.5 to 5.0 ppm. Wild fish were initially analyzed using gas chromatography/electron-capture detection (GC/ECD) and those having residues within the standard curve ranges were analyzed with ELISA. Results obtained using ELISA and GC/ECD were not significantly different (p < 0.05) from 0.05 to 0.5 ppm. From 0.5 to 5.0 ppm, the standard curve for Aroclor 1254 was the best predictor of total PCB in wild fish samples.

Trihalomethane and nonpurgeable total organic-halide formation potentials of the Mississippi river

USGS Publications Warehouse

Rathbun, R.E.

1996-01-01

Trihalomethane and nonpurgeable total organic-hallide formation potentials were determined for water samples from 12 sites along the Mississippi River from Minneapolis, MN, to New Orleans, LA, for the summer and fall of 1991 and the spring of 1992. The formation potentials increased with distance upstream, approximately paralleling the increase of the dissolved organic- carbon concentration. The pH and the dissolved organic-carbon and free- chlorine concentrations were significant variables in the prediction of the formation potentials. The trihalomethane formation potential increased as the pH increased, whereas the nonpurgeable total organic-halide formation potential decreased. All formation potentials increased as the dissolved organic-carbon and free-chlorine concentrations increased, with the dissolved organic-carbon concentration having a much greater effect.

Lithium and Beryllium By-product Recovery from the Round Top Mountain, Texas, Peraluminous Rhyolite Heavy Rare Earth Deposit

NASA Astrophysics Data System (ADS)

Pingitore, N. E., Jr.; Clague, J. W.; Gorski, D.

2016-12-01

The technology metals Li and Be combine low mass and unique properties. Li batteries are critical in applications at scales from micro-electronics to automotive and grid storage. Low mass Be structural components are essential in aerospace/defense applications and in non-sparking BeCu alloy oilfield tools. Most Li is sourced from desert salarsin the "Lithium Triangle" of Argentina—Bolivia—Chile. In contrast, Materion Corp mines >80% of global Be at Spor Mountain, UT. The massive peraluminous rhyolite heavy rare earth deposit at Round Top Mountain, TX is also enriched in Li, 500 ppm, and Be, 50 ppm. 2016 prices of 7000/tonne Li2CO3 (19% Li) and 1000/kg Be metal suggest favorable economics to extract Li and Be as by-products of HREE mining. Li and some Be are hosted in annite biotite that comprises up to 5% of the rhyolite. Texas Mineral Resources Corp proposes to heap leach crushed rhyolite with dilute H2SO4to release the yttrofluorite-hosted HREEs. At bench scale the annite biotite dissolves, but not quartz and feldspars (>90% of the rock). A series of 40 high-yield laboratory tests at various acid strength, particle size, and exposure time released up to 350 ppm (70%) of the Li and 14 ppm (30%) of the Be. For a 20,000 tonne/day operation, these recoveries correspond to daily production of >3 tonnes Li and 250 kg Be. Higher Li and Be recoveries also increased yields of gangue elements, Fe & Al, into solution. This complicates subsequent separation of Li, Be, and HREEs from the pregnant leach solution. Recovery of target HREEs did not increase beyond 200 ppm Li and 8 ppm Be recovery. Greater Li and Be recoveries increased acid consumption. Thus the "sweet spot" economics for heap leach is likely under conditions of acid strength, grain size, and exposure time that do not maximize by-product Li and Be recoveries. Evolving market prices for the full target element suite and additional costs to recover and purify the Li and Be must also be considered.

Phosphate Solubilization Potentials of Rhizosphere Isolates from Central Anatolia (Turkey)

NASA Astrophysics Data System (ADS)

Ogut, M.; Er, F.

2009-04-01

Plant available-phosphorus (P) is usually low in Anatolian soils due mainly to the precipitation as calcium (Ca) and magnesium (Mg) phosphates in alkaline conditions. Phosphate solubilizing microorganisms (PSM) can enhance plant P-availability by dissolving the hardly soluble-P within the rhizosphere, which is the zone that surrounds the plant roots. PSM's can be used as seed- or soil-inocula to increase plant P-uptake and the overall growth. A total of 162 PSM's were isolated from the rhizosphere of wheat plants excavated from different fields located along a 75 km part of a highway in Turkey. The mean, the standart deviation, and the median for solubilized-P (ppm) in a 24 h culture in a tricalcium phosphate broth were 681, 427, and 400 for glucose; 358, 266, and 236 for sucrose; and 102, 117, and 50 for starch, respectively. There was not a linear relationship between the phosphate solubilized in the liquid cultures and the solubilization index obtained in the Pikovskaya's agar. Nine isolates representing both weak and strong solubilizers [Bacillus megaterium (5), Bacillus pumilis (1), Pseudomonas syringae pv. phaseolica (1), Pseudomonas fluorescens (1), Arthrobacter aurescens (1) as determined by the 16S rRNA gene sequence analysis] were further studied in a five day incubation. Pseudomonas syringae pv. phaseolica solubilized statistically (P<0.05) higher phosphate (409 ppm) than all the other strains did. There was not a statistically significant (P<0.05) difference in solubilized-P among the Bacillus strains. The pH of the medium fell to the levels between 4 and 5 from the initial neutrality. The phosphate solubilizing strains variably produced gluconic, 2-keto-D-gluconic, glycolic, acetic and butyric acids. The organic acids produced by these microorganisms seem to be the major source of phosphate solubilization in vitro.

Titanium hydride and hydrogen concentration in acid-etched commercially pure titanium and titanium alloy implants: a comparative analysis of five implant systems.

PubMed

Szmukler-Moncler, S; Bischof, M; Nedir, R; Ermrich, M

2010-09-01

Acid etching is a popular method to texture the surface of dental implants. During etching, the titanium oxide protective layer is dissolved and small native hydrogen ions diffuse into the unprotected implant surface. They enrich the implant surface with hydrogen and precipitate into titanium hydride (TiH). The aim of this study was to measure the concentration of TiH at the implant surface and the total concentration of Hydrogen at five commercially available implant systems, made of either commercially pure (cp) titanium or titanium alloy. X-Ray diffraction (XRD) was conducted on each implant system to determine the compounds present at the implant surface. Following a TiH(2)/Ti calibration curve, the concentration of TiH was determined. Concentration of hydrogen in the implants was measured by the inert gas fusion thermal conductivity/infrared detection method. XRD data showed that TiH was present on all cp titanium implants but not on the alloyed implants. TiH concentration varied between 5% and 37%. Hydrogen concentration varied between 43 and 108 ppm, no difference in uptake was found between the cp titanium and alloyed implants. Low solubility of hydrogen in alpha-titanium is responsible for precipitation into TiH. Stronger etching conditions led to higher concentration of TiH2-x. High solubility of hydrogen in the beta-phase of the alloy is preventing hydrogen from precipitating into TiH. All implants, even those lacking TiH at the surface, were enriched with hydrogen. In all implants, hydrogen concentration was within the normative limit of 130 ppm.

Environmental assessment of NH/sub 3/ injection for an industrial package boiler. Volume 1. Technical results. Final report, January 1983-January 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaldini, C.; DeRosier, R.; Waterland, L.R.

1986-02-01

The report discusses emission results from comprehensive flue gas sampling of a gas- and oil-fired industrial boiler equipped with Exxon's Thermal DeNO/sub x/ Ammonia Injection Process for NO/sub x/ reduction. Comprehensive emission measurements included continuous monitoring of flue gas emissions; source assessment sampling system (SASS) tests; EPA Method 5/17 for solid and condensible particulate emissions and ammonia emissions; controlled condensation system for SO/sub 2/ and SO/sub 3/; and N/sub 2/O emission sampling. Ammonia injection at a NH/sub 3//NO molar ratio of 2.52 gave a NO/sub x/ reduction of 41% from an uncontrolled level of 234 ppm to a controlled levelmore » of 137 ppm. NH/sub 3/ emissions increased from 11 ppm for the baseline to an average of 430 ppm for ammonia injection. Nitrous oxide, N/sub 2/O was reduced 68% from a 50 ppm baseline level to a 17 ppm controlled level. Total particulate emissions increased by an order of magnitude from a baseline of 17.7 ng/J to a controlled level of 182 ng/J. The increase is in part attributed to formation of ammonia sulfate and bisulfate from residual ammonia and SO/sub x/. Total organic emissions were at a moderate level and showed a relative concentration in the nonvolatile category. Organic emissions of CO and trace inorganic elements were not significantly affected by ammonia injection.« less

[Proximal composition, lipid and cholesterol content of meat from pigs fed peach-palm meal (Bactris gasipaes Kunth) and synthetic lysine].

PubMed

Jerez-Timaure, Nancy; Rivero, Janeth Colina; Araque, Humberto; Jiménez, Paola; Velazco, Mariela; Colmenares, Ciolys

2011-03-01

Two experiments were conducted to evaluate the proximal composition, lipids and cholesterol content of meat from pigs fed diets with peach-palm meal (PPM), with or without addition of synthetic lysine (LYS). In experiment 1, 24 pigs were randomly allotted into six treatments with three levels of PPM (0.16 and 32%) and two levels of LYS (0 and 0.27%). In experiment II, 16 finishing pigs were fed with two levels of PPM (0 and 17.50%) and two levels of LYS (0 and 0.27%). At the end of each experiment (42 and 35 d, respectively), pigs were slaughtered and loin samples were obtained to determine crude protein, dry matter, moisture, ash, total lipids, and cholesterol content. In experiment I, pork loin from 16% PPM had more dry matter (26.45 g/100 g) and less moisture (73.49 g/100g) than pork loin from 32% PPM (25.11 y 75.03 g/100g, respectively). Meat samples from pigs without LYS had higher (p < 0.05) content of lipids (2.11 g/100 g) than meat from pigs that consumed LYS (1.72 g/100 g). In experiment II, the proximal, lipids and cholesterol content were similar among treatments. The PPM addition to pig diets did not affect the proximal composition of pork, while LYS addition indicated a reduction of total lipids, which could result as an alternative to obtain leaner meat.

Hair methylmercury levels of mummies of the Aleutian Islands, Alaska

DOE Office of Scientific and Technical Information (OSTI.GOV)

Egeland, G.M.; Ponce, Rafael; Bloom, Nicolas S.

2009-04-15

Ancient human hair specimens can shed light on the extent of pre-historic exposures to methylmercury and provide valuable comparison data with current-day exposures, particularly for Indigenous Peoples who continue to rely upon local traditional food resources. Human hair from ancient Aleutian Island Native remains were tested for total and methylmercury (Hg, MeHg) and were radiocarbon dated. The remains were approximately 500 years old (1450 A.D.). For four adults, the mean and median total hair mercury concentration was 5.8 ppm (SD=0.9). In contrast, MeHg concentrations were lower with a mean of 1.2 ppm (SD=1.8) and a median of 0.54 ppm (0.12-3.86).more » For the five infants, the mean and median MeHg level was 1.2 ppm (SD=1.8) and 0.20 ppm (0.007-4.61), respectively. Segmental analyses showed variations in MeHg concentrations in 1-cm segments, consistent with fluctuations in naturally occurring exposure to mercury through dietary sources. The levels are comparable to or lower than those found in fish and marine mammal-eating populations today who rely far less on subsistence food than pre-historic humans. The findings are, therefore, compatible with increased anthropogenic release of trace metals during the past several centuries.« less

21 CFR 556.430 - Neomycin.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., AND RELATED PRODUCTS TOLERANCES FOR RESIDUES OF NEW ANIMAL DRUGS IN FOOD Specific Tolerances for Residues of New Animal Drugs § 556.430 Neomycin. (a) Acceptable daily intake (ADI). The ADI for total..., and goats. 7.2 parts per million (ppm) in kidney (target tissue) and fat, 3.6 ppm in liver, and 1.2...

21 CFR 556.430 - Neomycin.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., AND RELATED PRODUCTS TOLERANCES FOR RESIDUES OF NEW ANIMAL DRUGS IN FOOD Specific Tolerances for Residues of New Animal Drugs § 556.430 Neomycin. (a) Acceptable daily intake (ADI). The ADI for total..., and goats. 7.2 parts per million (ppm) in kidney (target tissue) and fat, 3.6 ppm in liver, and 1.2...

21 CFR 556.430 - Neomycin.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., AND RELATED PRODUCTS TOLERANCES FOR RESIDUES OF NEW ANIMAL DRUGS IN FOOD Specific Tolerances for Residues of New Animal Drugs § 556.430 Neomycin. (a) Acceptable daily intake (ADI). The ADI for total..., and goats. 7.2 parts per million (ppm) in kidney (target tissue) and fat, 3.6 ppm in liver, and 1.2...

Low PCB concentrations observed in American eel (Anguilla rostrata) in six Hudson River tributaries

USGS Publications Warehouse

Limburg, K.E.; Machut, L.S.; Jeffers, P.; Schmidt, R.E.

2008-01-01

We analyzed 73 eels, collected in 2004 and 2005 above the head of tide in six Hudson River tributaries, for total PCBs, length, weight, age, and nitrogen stable isotope ratios (??15N). Mean total PCB concentration (wet weight basis) was 0.23 ppm ?? 0.08 (standard error), with a range of 0.008 to 5.4 ppm. A majority of eels (84) had concentrations below 0.25 ppm, and only seven eels (10%) had concentrations exceeding 0.5 ppm. Those eels with higher PCB concentrations were ???12 yr; there was a weak correlation of PCB concentration with ??15N and also with weight. Compared to recent (2003) data from the mainstem of the Hudson River estuary, these results indicate that tributaries are generally much less contaminated with PCBs. We hypothesize that those tributary eels with high PCB concentrations were relatively recent immigrants from the mainstem. Given concern over the possible adverse effects of PCBs on eel reproduction, these tributaries may serve as refugia. Therefore, providing improved access to upland tributaries may be critically important to this species. ?? 2008 Northeastern Naturalist.

Treatment of kitchen wastewater using Eichhornia crassipes

NASA Astrophysics Data System (ADS)

Parwin, Rijwana; Karar Paul, Kakoli

2018-03-01

The efficiency of Eichhornia crassipes for treatment of raw kitchen wastewater was studied in the present research work. An artificial wetland of 30 liter capacity was created for phytoremediation of kitchen wastewater using Eichhornia crassipes. Kitchen wastewater samples were collected from hostel of an educational institute in India. Samples were characterized based on physical and chemical parameters such as pH, turbidity, total hardness, nitrate-nitrogen, ammonium-nitrogen, sulphate, dissolved oxygen, total organic carbon and total dissolved solid. The physico-chemical parameter of kitchen wastewater samples were analysed for durations of 0 (initial day), 4 and 8 days. After 8 days of retention period, it was observed that pH value increases from 6.25 to 6.63. However, percentage reduction for turbidity, total hardness, nitrate-nitrogen, ammonium-nitrogen, sulphate, dissolved oxygen, total organic carbon and total dissolved solid were found to be 74.71%, 50%, 78.75%, 60.28%, 25.31%, 33.33%, 15.38% and 69.97%, respectively. Hence water hyacinth (Eichhornia crassipes) is found efficient and easy to handle and it can be used for low cost phytoremediation technique.

Superfund Record of Decision Amendment (EPA Region 6): Texarkana Wood Preserving Co. , Texarkana, TX, March 13, 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This decision document presents an amendment to the selected remedial action for the Texarkana Wood Preserving Co. Superfund Site. This amendment fundamentally changes the Record of Decision (ROD) executed by the Regional Administrator on September 25, 1990. This amended remedy will seal and contain soils contaminated with greater than 3 ppm (parts per million) benzo(a)pyrene equivalents, 2450 ppm total poly aromatic hydrocarbons (PAH), 20 ppb (parts per billion) as 2,3,7,8 TCDD equivalents and 150 ppm pentachlorophenol beneath a soil cap.

Hair mercury concentrations and in vitro fertilization (IVF) outcomes among women from a fertility clinic

PubMed Central

Ehrlich, Shelley; Smith, Kristen; Williams, Paige L.; Chavarro, Jorge E.; Batsis, Maria; Toth, Thomas L.; Hauser, Russ

2015-01-01

Total hair mercury (Hg) was measured among 205 women undergoing in vitro fertilization (IVF) treatment and the association with prospectively collected IVF outcomes (229 IVF cycles) was evaluated. Hair Hg levels (median=0.62 ppm, range: 0.03-5.66 ppm) correlated with fish intake (r=0.59), and exceeded the recommended EPA reference of 1ppm in 33% of women. Generalized linear mixed models with random intercepts accounting for within-woman correlations across treatment cycles were used to evaluate the association of hair Hg with IVF outcomes adjusted for age, body mass index, race, smoking status, infertility diagnosis, and protocol type. Hair Hg levels were not related to ovarian stimulation outcomes (peak estradiol levels, total and mature oocyte yields) or to fertilization rate, embryo quality, clinical pregnancy rate or live birth rate. PMID:25601638

Health assessment for Kaiser Aluminum and Chemical Corporation, Mead, Spokane County, Washington, Region 10. CERCLIS No. WAD000065508. Preliminary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-04-12

The 240-acre Kaiser Aluminum Site is on the National Priorities List. The plant was built in 1942 as an aluminum-reduction facility. Concentrations of cyanide (total) in the river range from 0.011 to 1.7 parts per million (ppm) and free cyanide concentrations ranged from non-detected (ND) to 0.58 ppm. Soils on-site are contaminated with cyanide and fluoride; total cyanide levels range from ND to 985 ppm. The site is considered to be of potential public health concern because of the risk to human health caused by the possibility of exposure to hazardous substances via ingestion of contaminated ground water, dermal absorptionmore » of contaminants found in the surface soils on-site, and inhalation of and dermal contact with reentrained contaminated dust.« less

Interactive effects of arsenate, selenium, and dietary protein on survival, growth, and physiology in mallard ducklings

USGS Publications Warehouse

Hoffman, D.J.; Sanderson, C.J.; LeCaptain, L.J.; Cromartie, E.; Pendleton, G.W.

1992-01-01

High concentrations of arsenic (As) and selenium (Se) have been found in aquatic food chains associated with irrigation drainwater. Total biomass of invertebrates, a maJor source of protein for wild ducklings, may vary in environments that are contaminated with selenium. Dayold mallard (Anas platyrhynchos) ducklings received an untreated diet (controls) containing 22% protein or diets containing 15 ppm Se (as selenomethionine), 60 ppm Se, 200 ppm As (as sodium arsenate), 15 ppm Se with 200 ppm As, or 60 ppm Se with 200 ppm As. In a concurrent experiment, the same sequence was repeated with a proteinrestricted (7%) but isocaloric diet. After 4 weeks, blood and tissue samples were collected for biochemical and histological examination. With 22% protein and 60 ppm Se in the diet, duckling survival and growth was reduced and livers had histopathological lesions. Arsenic alone caused some reduction in growth. Antagonistic interactive effects occurred between As and Se, including complete to partial alleviation of the following Se effects: mortality, impaired growth, hepatic lesions and lipid peroxidation, and altered glutathione and thiol status. With 7% protein, survival and growth of controls was less than that with 22% protein, Se (60 ppm) caused 100% mortality, and As (200 ppm) caused mortality, decreased growth, and liver histopathology. These findings suggest the potential for antagonistic effects of Se and As on duckling survival, growth, and physiology with adequate dietary protein but more severe toxicological effects when dietary protein is diminished.

A robust and reliable optical trace oxygen sensor

NASA Astrophysics Data System (ADS)

McDowell, G. R.; Holmes-Smith, A. S.; Uttamlal, M.; Mitchell, C.; Shannon, P. H.

2017-05-01

In applications of nitrogen (N2) generation, industrial gas manufacturing and food packaging there is a need to ensure oxygen (O2) is absent from the environment, even at the lowest concentration levels. Therefore, there has been an increased growth in the development of trace O2 parts per million (ppm) sensors over the past decade to detect and quantify the concentration of molecular O2 in the environment whether it be dissolved or gaseous O2. The majority of commercially available trace O2 sensors are based on electrochemical, zirconia and paramagnetic technologies. Here, the development of a luminescence-based optical trace O2 sensor is presented. Luminescence-based sensing is now regarded as one of the best techniques for the detection and quantification of O2. This is due to the high detection sensitivity, no O2 is consumed and there are a vast array of luminescent indicators and sensing platforms (polymers) that can be selected to suit the desired application. The sensor will be shown to operate from -30 °C to +60 °C in the 0-1000 ppm and/or 0-1200 μbar partial pressure of oxygen (ppO2) range and is equipped with temperature and pressure compensation. The luminescence non-depleting principle, sensor specifications and miniaturized nature offers an attractive alternative to other sensing technologies and advantages over other luminescence-based O2 ppm sensors.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patterson, D.T.; Flint, E.P.

Mathematical growth analysis techniques were used to evaluate the effects of CO/sub 2/ concentrations of 350, 600, and 1000 ppm (v/v) on growth and biomass partitioning in corn (Zea mays L. Dekalb (L 395'), itchgrass (Rottboellia exaltata L.f.), soybean (Glycine max L) Merr. Tracy), and velvetleaf (Abutilon theophrasti Medic.). Controlled environment chambers with day/night temperatures of 28/22 C and photosynthetic photon flux densities (PPFD) of 650 ..mu..E (microeinteins) m/sup -2/ s/sup -1/ were used. Dry matter production in the two C/sub 3/ species soybean and velvetleaf) was increased significantly by raising the CO/sub 2/ concentration above 350 ppm. In cornmore » (a C/sub 4/ species), dry matter production was greatest at 600 ppm CO/sub 2/ and did not differ between the 350 and 1000 ppm treatments. Increasing the CO/sub 2/ concentration increased the rate of dry matter production per unit leaf area (net assimilation rate or NAR) in soybean and velvetleaf but either decreased or did not alter NAR in corn and itchgrass. At 45 days after planting, the weed/crop ratios for total dry matter production for velvetleaf/corn and itchgrass/corn were significantly greater at both 600 and 1000 ppm than at 350 ppm CO/sub 2/. The weed/crop ratio for itchgrass/soybean was less at 1000 ppm than at 350 or 600 ppm CO/sub 2/. Compared to the value at 350 ppm, the weed/crop ratio for velvetleaf/soybean was greater at 600 ppm and less at 100 ppm CO/sub 2/.« less

Trends in the quality of water in New Jersey streams, water years 1998-2007

USGS Publications Warehouse

Hickman, R. Edward; Gray, Bonnie J.

2010-01-01

Trends were determined in flow-adjusted values of selected water-quality characteristics measured year-round during water years 1998-2007 (October 1, 1997, through September 30, 2007) at 70 stations on New Jersey streams. Water-quality characteristics included in the analysis are dissolved oxygen, pH, total dissolved solids, total phosphorus, total organic nitrogen plus ammonia, and dissolved nitrate plus nitrite. In addition, trend tests also were conducted on measurements of dissolved oxygen made only during the growing season, April to September. Nearly all the water-quality data analyzed were collected by the New Jersey Department of Environmental Protection and the U.S. Geological Survey as part of the New Jersey Department of Environmental Protection Ambient Surface-Water Quality Monitoring Network. Monotonic trends in flow-adjusted values of water quality were determined by use of procedures in the ESTREND computer program. A 0.05 level of significance was selected to indicate a trend. Results of tests were not reported if there were an insufficient number of measurements or insufficient number of detected concentrations, or if the results of the tests were affected by a change in data-collection methods. Trends in values of dissolved oxygen, pH, and total dissolved solids were identified using the Seasonal Kendall test. Trends or no trends in year-round concentrations of dissolved oxygen were determined for 66 stations; decreases at 4 stations and increases at 0 stations were identified. Trends or no trends in growing-season concentrations of dissolved oxygen were determined for 65 stations; decreases at 4 stations and increases at 4 stations were identified. Tests of pH values determined trends or no trends at 26 stations; decreases at 2 stations and increases at 3 stations were identified. Trends or no trends in total dissolved solids were reported for all 70 stations; decreases at 0 stations and increases at 24 stations were identified. Trends in total phosphorus, total organic nitrogen plus ammonia, and dissolved nitrate plus nitrite were identified by use of Tobit regression. Two sets of trend tests were conducted-one set with all measurements and a second set with all measurements except the most extreme outlier if one could be identified. The result of the test with all measurements is reported if the results of the two tests are equivalent. The result of the test without the outlier is reported if the results of the two tests are not equivalent. Trends or no trends in total phosphorus were determined for 69 stations. Decreases at 12 stations and increases at 5 stations were identified. Of the five stations on the Delaware River included in this study, decreases in concentration were identified at four. Trends or no trends in total organic nitrogen plus ammonia were determined for 69 stations. Decreases and increases in concentrations were identified at six and nine stations, respectively. Trends or no trends in dissolved nitrate plus nitrite were determined for 66 stations. Decreases and increases in concentration were identified at 4 and 19 stations, respectively.

Growth of vegetative explant Moringa oleifera on different composition of auxin and cytokinin and its synthetic seed germination

NASA Astrophysics Data System (ADS)

Muslihatin, Wirdhatul; Jadid, Nurul; Puspitasari, Ika D.; Safitri, Chusnul E.

2017-06-01

The spread of Moringa oleifera is also rare for seed germination and viability or survival are low, and the lack of vegetative propagation method. The purpose of this study are to determine the effect of auxin and cytokinin on growth vegetative explants Moringa oleifera and its synthetic seed germination. The explants grown on MS medium with sucrose content of 30% and a range of additional hormone. Addition concentration and different types of hormone made in order to know the sensitivity and response explant growth on a variety of media to get a good callus and embryosomatic. The composition of the hormone given is MS + 2.4 D 3 ppm; MS + 2,4D 2 ppm + BAP 2 ppm; MS + NAA + 0.5 ppm kinetin 1 ppm; MS + NAA 1 ppm + kinetin 1 ppm; MS + NAA 1 ppm + 0.5 ppm kinetin. The explants were incubated at a temperature of 18-20 ° C with a photoperiod 16/8. Explants and MS medium is incubated to form embryonic callus. Seeds synthetic made from embryonic callus growing on medium 1 ppm kinetin + NAA 1 ppm with encapsulation method with sodium alginate 2%. Seed synthetic germinated in some kind of medium that medium ms0 solid (M1), ms0 liquid (M2), MS0 semi-solid (M3), MS solid NAA 1ppm + Kinetin 1 ppm (M4), MS liquid NAA 1 ppm + kinetin (M5), and semi-solid MS + NAA 1 ppm kinetin 1 ppm (M6). Synthetic seed viability was observed with the parameters of the fresh weight of synthetic seed, germination percentage and seedling. Chlorophyll content was measured by spectrophotometric method with solvent asseton. Best callus generated in this study are embryonic callus that grew on media NAA 1 ppm + kinetin 1 ppm. Embryonic callus on M6 + NAA 1 ppm kinetin 1 ppm capable of germination with an average weight of callus and sprouts of 40.38 mg. Of the entire amount of a synthetic seed on M6, just 5 seed germinate, so the percentage of germination of seeds is equal to 41.67%. with an average length of sprouts 1 cm with an average total chlorophyll content of 8.66 mg / g.

MIR hollow waveguide (HWG) isotope ratio analyzer for environmental applications

NASA Astrophysics Data System (ADS)

Wang, Zhenyou; Zhuang, Yan; Deev, Andrei; Wu, Sheng

2017-05-01

An advanced commercial Mid-InfraRed Isotope Ratio (IR2) analyzer was developed in Arrow Grand Technologies based on hollow waveguide (HWG) as the sample tube. The stable carbon isotope ratio, i.e. δ13C, was obtained by measuring the selected CO2 absorption peaks in the MIR. Combined with a GC and a combustor, it has been successfully employed to measure compound specific δ13C isotope ratios in the field. By using both the 1- pass HWG and 5-path HWG, we are able to measure δ13C isotope ratio at a broad CO2 concentration of 300 ppm-37,500 ppm. Here, we demonstrate its applications in environmental studies. The δ13C isotope ratio and concentration of CO2 exhaled by soil samples was measured in real time with the isotope analyzer. The concentration was found to change with the time. We also convert the Dissolved Inorganic Carbon (DIC) into CO2, and then measure the δ13C isotope ratio with an accuracy of better than 0.3 ‰ (1 σ) with a 6 min test time and 1 ml sample usage. Tap water, NaHCO3 solvent, coca, and even beer were tested. Lastly, the 13C isotope ratio of CO2 exhaled by human beings was obtained <10 seconds after simply blowing the exhaled CO2 into a tube with an accuracy of 0.5‰ (1 σ) without sample preconditioning. In summary, a commercial HWG isotope analyzer was demonstrated to be able to perform environmental and health studies with a high accuracy ( 0.3 ‰/Hz1/2 1 σ), fast sampling rate (up to 10 Hz), low sample consumption ( 1 ml), and broad CO2 concentration range (300 ppm-37,500 ppm).

Inactivation of human norovirus using chemical sanitizers.

PubMed

Kingsley, David H; Vincent, Emily M; Meade, Gloria K; Watson, Clytrice L; Fan, Xuetong

2014-02-03

The porcine gastric mucin binding magnetic bead (PGM-MB) assay was used to evaluate the ability of chlorine, chlorine dioxide, peroxyacetic acid, hydrogen peroxide, and trisodium phosphate to inactivate human norovirus within 10% stool filtrate. One-minute free chlorine treatments at concentrations of 33 and 189 ppm reduced virus binding in the PGM-MB assay by 1.48 and 4.14 log₁₀, respectively, suggesting that chlorine is an efficient sanitizer for inactivation of human norovirus (HuNoV). Five minute treatments with 5% trisodium phosphate (pH~12) reduced HuNoV binding by 1.6 log₁₀, suggesting that TSP, or some other high pH buffer, could be used to treat food and food contact surfaces to reduce HuNoV. One minute treatments with 350 ppm chlorine dioxide dissolved in water did not reduce PGM-MB binding, suggesting that the sanitizer may not be suitable for HuNoV inactivation in liquid form. However a 60-min treatment with 350 ppm chlorine dioxide did reduce human norovirus by 2.8 log₁₀, indicating that chlorine dioxide had some, albeit limited, activity against HuNoV. Results also suggest that peroxyacetic acid has limited effectiveness against human norovirus, since 1-min treatments with up to 195 ppm reduced human norovirus binding by <1 log₁₀. Hydrogen peroxide (4%) treatment of up to 60 min resulted in minimal binding reduction (~0.1 log₁₀) suggesting that H₂O₂ is not a good liquid sanitizer for HuNoV. Overall this study suggests that HuNoV is remarkably resistant to several commonly used disinfectants and advocates for the use of chlorine (sodium hypochlorite) as a HuNoV disinfectant wherever possible. Copyright © 2013. Published by Elsevier B.V.

Phenomenological aspects of fatigue cracking in as-received and hardened F82H modified steel exposed to lithiated water with dissolved hydrogen at 240°C

NASA Astrophysics Data System (ADS)

Maday, Marie-Françoise

2000-12-01

The low cycle fatigue (LCF) behaviour of F82H modified steel with three different degrees of hardness produced by specific thermal treatments has been investigated at 240°C under load control, in oxygen-free lithiated solutions containing either no or 2 ppm dissolved hydrogen. In all cases, it was found that the aqueous environments reduced the fatigue life of the material and promoted fracture modes different from those observed in air tests; the fracture modes comprised intergranular and transgranular quasi-cleavage separations as well as microvoid coalescence, which depended on material conditions and water chemistry. All these features were ascribed to a hydrogen-assisted-cracking (HAC) phenomenon, as the basic mechanism for controlling the fatigue behaviour of various F82H heats in lithiated solutions. The observed differences in HAC paths are discussed from the standpoint of material microstructural and substructural parameters.

Natural realgar and amorphous AsS oxidation kinetics

NASA Astrophysics Data System (ADS)

Lengke, Maggy F.; Tempel, Regina N.

2003-03-01

The oxidation rates of natural realgar and amorphous synthetic AsS by dissolved oxygen were evaluated using mixed flow reactors at pH 7.2 to 8.8 and dissolved oxygen contents of 5.9 to 16.5 ppm over a temperature range of 25 to 40°C. The ratios of As/S are stoichiometric for all amorphous AsS oxidation experiments except for two experiments conducted at pH ˜8.8. In these experiments, stoichiometric ratios of As/S were only observed in the early stages of AsS (am) oxidation whereas lower As/S ratios were observed during steady state. For realgar oxidation experiments, the As/S ratio is less than the stoichiometric ratio of realgar, ranging between 0.61 and 0.71. This nonstoichiometric release of As and S to solution indicates that realgar oxidation is more selective for S after the rates of oxidation become constant. All measured oxidation rates at 25°C can be described within experimental uncertainties as follows: Table 1

NITRATE CONVERSION OF HB-LINE REILLEXTM HPQ RESIN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steimke, J.; Williams, M.; Steeper, T.

Reillex{trademark} HPQ ion exchange resin is used by HB Line to remove plutonium from aqueous streams. Reillex{trademark} HPQ resin currently available from Vertellus Specialties LLC is a chloride ionic form, which can cause stress corrosion cracking in stainless steels. Therefore, HB Line Engineering requested that Savannah River National Laboratory (SRNL) convert resin from chloride form to nitrate form in the Engineering Development Laboratory (EDL). To perform this task, SRNL treated two batches of resin in 2012. The first batch of resin from Reilly Industries Batch 80302MA was initially treated at SRNL in 2001 to remove chloride. This batch of resin,more » nominally 30 liters, has been stored wet in carboys since that time until being retreated in 2012. The second batch of resin from Batch 23408 consisted of 50 kg of new resin purchased from Vertellus Specialties in 2012. Both batches were treated in a column designed to convert resin using downflow of 1.0 M sodium nitrate solution through the resin bed followed by rinsing with deionized water. Both batches were analyzed for chloride concentration, before and after treatment, using Neutron Activation Analysis (NAA). The resin specification [Werling, 2003] states the total chlorine and chloride concentration shall be less than 250 ppm. The resin condition for measuring this concentration is not specified; however, in service the resin would always be fully wet. Measurements in SRNL showed that changing from oven dry resin to fully wet resin, with liquid in the particle interstices but no supernatant, increases the total weight by a factor of at least three. Therefore, concentration of chlorine or chloride expressed as parts per million (ppm) decreases by a factor of three. Therefore, SRNL recommends measuring chlorine concentration on an oven dry basis, then dividing by three to estimate chloride concentration in the fully wet condition. Chloride concentration in the first batch (No.80302MA) was nearly the same before the current treatment (759 ppm dry) and after treatment (745 ppm dry or {approx}248 ppm wet). Treatment of the second batch of resin (No.23408) was very successful. Chloride concentration decreased from 120,000 ppm dry to an average of 44 ppm dry or {approx}15ppm wet, which easily passes the 250 ppm wet criterion. Per guidance from HB Line Engineering, SRNL blended Batch 80302 resin with Batch P9059 resin which had been treated previously by ResinTech to remove chloride. The chloride concentrations for the two drums of Batch P9059 were 248 ppm dry ({approx}83 ppm wet) {+-}22.8% and 583 ppm dry ({approx}194 ppm wet) {+-} 11.8%. The blended resin was packaged in five gallon buckets.« less

International test and demonstration of a 1-MW wellhead generator: Helical screw expander power plant

NASA Astrophysics Data System (ADS)

McKay, R. A.

1984-06-01

A 1-MW wellhead generator was tested in 1980, 1981, and 1982 by Mexico, Italy, and New Zealand at Cerro Prieto, Cesano, and Broadlands, respectively. The total flow helical screw expander portable power plant, Model 76-1, had been built for the U.S. Government and field-tested in Utah, USA, in 1978 and 1979. The expander had oversized internal clearances designed for self-cleaning operation on fluids that deposit adherent scale normally detrimental to the utiliation of liquid dominated fields. Conditions with which the expander was tested included inlet pressures of 64 to 220 psia, inlet qualities of 0% to 100%, exhaust pressures of 3.1 to 40 psia, electrial loads of idle and 110 to 933 kW, electrical frequencies of 50 and 60 Hz, male rotor speeds of 2500 to 4000 rpm, and fluid characteristics to 310,000 ppm total dissolved solids and noncondensables to 38 wt % of the vapor. Some testing was done on-grid. Typical expander isentropic efficiency was 40% to 50% with the clearances not closed, and 5 percentage points or more higher with the clearances partly closed. The expander efficiency increased approximately logarithmically with shaft power for most operations, while inlet quality, speed, and pressure ratio across the machine had only small effects. These findings are all in agreement with the Utah test results.

International test and demonstration of a 1-MW wellhead generator: Helical screw expander power plant

NASA Technical Reports Server (NTRS)

Mckay, R. A.

1984-01-01

A 1-MW wellhead generator was tested in 1980, 1981, and 1982 by Mexico, Italy, and New Zealand at Cerro Prieto, Cesano, and Broadlands, respectively. The total flow helical screw expander portable power plant, Model 76-1, had been built for the U.S. Government and field-tested in Utah, USA, in 1978 and 1979. The expander had oversized internal clearances designed for self-cleaning operation on fluids that deposit adherent scale normally detrimental to the utiliation of liquid dominated fields. Conditions with which the expander was tested included inlet pressures of 64 to 220 psia, inlet qualities of 0% to 100%, exhaust pressures of 3.1 to 40 psia, electrial loads of idle and 110 to 933 kW, electrical frequencies of 50 and 60 Hz, male rotor speeds of 2500 to 4000 rpm, and fluid characteristics to 310,000 ppm total dissolved solids and noncondensables to 38 wt % of the vapor. Some testing was done on-grid. Typical expander isentropic efficiency was 40% to 50% with the clearances not closed, and 5 percentage points or more higher with the clearances partly closed. The expander efficiency increased approximately logarithmically with shaft power for most operations, while inlet quality, speed, and pressure ratio across the machine had only small effects. These findings are all in agreement with the Utah test results.

Continuous water-quality monitoring and regression analysis to estimate constituent concentrations and loads in the Red River of the North, Fargo, North Dakota, 2003-05

USGS Publications Warehouse

Ryberg, Karen R.

2006-01-01

This report presents the results of a study by the U.S. Geological Survey, done in cooperation with the Bureau of Reclamation, U.S. Department of the Interior, to estimate water-quality constituent concentrations in the Red River of the North at Fargo, North Dakota. Regression analysis of water-quality data collected in 2003-05 was used to estimate concentrations and loads for alkalinity, dissolved solids, sulfate, chloride, total nitrite plus nitrate, total nitrogen, total phosphorus, and suspended sediment. The explanatory variables examined for regression relation were continuously monitored physical properties of water-streamflow, specific conductance, pH, water temperature, turbidity, and dissolved oxygen. For the conditions observed in 2003-05, streamflow was a significant explanatory variable for all estimated constituents except dissolved solids. pH, water temperature, and dissolved oxygen were not statistically significant explanatory variables for any of the constituents in this study. Specific conductance was a significant explanatory variable for alkalinity, dissolved solids, sulfate, and chloride. Turbidity was a significant explanatory variable for total phosphorus and suspended sediment. For the nutrients, total nitrite plus nitrate, total nitrogen, and total phosphorus, cosine and sine functions of time also were used to explain the seasonality in constituent concentrations. The regression equations were evaluated using common measures of variability, including R2, or the proportion of variability in the estimated constituent explained by the regression equation. R2 values ranged from 0.703 for total nitrogen concentration to 0.990 for dissolved-solids concentration. The regression equations also were evaluated by calculating the median relative percentage difference (RPD) between measured constituent concentration and the constituent concentration estimated by the regression equations. Median RPDs ranged from 1.1 for dissolved solids to 35.2 for total nitrite plus nitrate. Regression equations also were used to estimate daily constituent loads. Load estimates can be used by water-quality managers for comparison of current water-quality conditions to water-quality standards expressed as total maximum daily loads (TMDLs). TMDLs are a measure of the maximum amount of chemical constituents that a water body can receive and still meet established water-quality standards. The peak loads generally occurred in June and July when streamflow also peaked.

Total Dissolved Gas Monitoring in Chum Salmon Spawning Gravels Below Bonneville Dam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arntzen, Evan V.; Geist, David R.; Panther, Jennifer L.

2007-01-30

At the request of the U.S. Army Corps of Engineers (Portland District), Pacific Northwest National Laboratory (PNNL) conducted research to determine whether total dissolved gas concentrations are elevated in chum salmon redds during spring spill operations at Bonneville Dam. The study involved monitoring the total dissolved gas levels at egg pocket depth and in the river at two chum salmon spawning locations downstream from Bonneville Dam. Dissolved atmospheric gas supersaturation generated by spill from Bonneville Dam may diminish survival of chum (Oncorhynchus keta) salmon when sac fry are still present in the gravel downstream from Bonneville Dam. However, no previousmore » work has been conducted to determine whether total dissolved gas (TDG) levels are elevated during spring spill operations within incubation habitats. The guidance used by hydropower system managers to provide protection for pre-emergent chum salmon fry has been to limit TDG to 105% after allowing for depth compensation. A previous literature review completed in early 2006 shows that TDG levels as low as 103% have been documented to cause mortality in sac fry. Our study measured TDG in the incubation environment to evaluate whether these levels were exceeded during spring spill operations. Total dissolved gas levels were measured within chum salmon spawning areas near Ives Island and Multnomah Falls on the Columbia River. Water quality sensors screened at egg pocket depth and to the river were installed at both sites. At each location, we also measured dissolved oxygen, temperature, specific conductance, and water depth to assist with the interpretation of TDG results. Total dissolved gas was depth-compensated to determine when levels were high enough to potentially affect sac fry. This report provides detailed descriptions of the two study sites downstream of Bonneville Dam, as well as the equipment and procedures employed to monitor the TDG levels at the study sites. Results of the monitoring at both sites are then presented in both text and graphics. The findings and recommendations for further research are discussed, followed by a listing of the references cited in the report.« less

Effects of long-term land use change on dissolved carbon characteristics in the permafrost streams of northeast China.

PubMed

Guo, Yuedong; Song, Changchun; Wan, Zhongmei; Tan, Wenwen; Lu, Yongzheng; Qiao, Tianhua

2014-11-01

Permafrost soils act as large sinks of organic carbon but are highly sensitive to interference such as changes in land use, which can greatly influence dissolved carbon loads in streams. This study examines the effects of long-term land reclamation on seasonal concentrations of dissolved carbons in the upper reaches of the Nenjiang River, northeast China. A comparison of streams in natural and agricultural systems shows that the dissolved organic carbon (DOC) concentration is much lower in the agricultural stream (AG) than in the two natural streams (WAF, wetland dominated; FR, forest dominated), suggesting that land use change is associated with reduced DOC exporting capacity. Moreover, the fluorescence indexes and the ratio of dissolved carbon to nitrogen also differ greatly between the natural and agricultural streams, indicating that the chemical characteristics and the origin of the DOC released from the whole reaches are also altered to some extent. Importantly, the exporting concentration of dissolved inorganic carbon (DIC) and its proportion of total dissolved carbon (TDC) substantially increase following land reclamation, which would largely alter the carbon cycling processes in the downstream fluvial system. Although the strong association between the stream discharge and the DOC concentration was unchanged, the reduction in total soil organic carbon following land reclamation led to remarkable decline of the total flux and exporting coefficient of the dissolved carbons. The results suggest that dissolved carbons in permafrost streams have been greatly affected by changes in land use since the 1970s, and the changes in the concentration and chemical characteristics of dissolved carbons will last until the alteration in both the traditional agriculture pattern and the persistent reclamation activities.

Effects of ozone or sulfur dioxide on annual plants of the Mojave Desert. [Camissonia claviformis; Camissonia hirtella; Cryptantha nevadensis; Festuca octoflora; Lepidium lasiocarpum; Baileya pleniradiata; Perityle emoryi; Oenothera californica

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, C.R.; Olszyk, D.M.; Kats, G.

1984-10-01

Forty-seven species of annual plants from the Mojave Desert were grown in pots and exposed in open-top field chambers located at Riverside, California to test their relative sensitivity to SO/sub 2/ and O/sub 3/. Exposures were 8 h/day for four or five days at 0, 0.05, 0.1, 0.2, 0.3 and 0.4 ppm O/sub 3/ or 0, 0.2, 0.5, 0.6, 0.8, 1.0 and 1.5 ppm SO/sub 2/. Species differed widely in their response to the pollutants. Three species, Camissonia claviformis, Camissonia hirtella and Cryptantha nevadensis, were quite sensitive to both pollutants, exhibiting leaf injury when exposed to 0.1 ppm O/sub 3/more » or 0.2 ppm SO/sub 2/. Two species: Festuca octoflora and Lepidium lasiocarpum were tolerant to both pollutants, exhibiting no leaf injury with concentrations of 0.3 ppm O/sub 3/ or 1.5 ppm SO/sub 2/. The other species were intermediate in sensitivity, with O/sub 3/ sensitivity not always corresponding to SO/sub 2/ sensitivity. Total sulfur concentration analysis indicated that for 8 of 11 species tested, plants exposed to 0.2 ppm SO/sub 2/ had a higher sulfur concentration than nonexposed plants. Baileya pleniradiata and Perityle emoryi had the greatest increases in sulfur concentration for exposed versus control plants. To test for effects of the environmental and exposure system on plant sensitivity, 29 of the species exposed in the open-top chambers were grown in the ground and exposed with a modified chamberless zonal air pollution (ZAP) system to SO/sub 2/ in the Mojave Desert area near Daggett, California. Exposures were for a total of 37 h over six days to 0, 0.4, 0.8 and 1.0 ppm SO/sub 2/ with exposures only during periods with due west winds. Most of the species were not injured with any of the SO/sub 2/ exposure concentrations used with the ZAP system; only Camissonia claviformis showed injury at 0.8 ppm SO/sub 2/ and Oenothera californica exhibited injury at 1.0 ppm SO/sub 2/.« less

40 CFR 432.115 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... Coliform ( 2 ) ( 3 ) O&G (as HEM) 14 8.0 TSS 30 20 1 mg/L (ppm). 2 Maximum of 400 MPN or CFU per 100 mL at... Coliform (2) (3) O&G (as HEM) 14 8.0 TSS 30 20 Total Nitrogen 147 103 1 mg/L (ppm). 2 Maximum of 400 MPN or...

40 CFR 432.115 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... Coliform ( 2 ) ( 3 ) O&G (as HEM) 14 8.0 TSS 30 20 1 mg/L (ppm). 2 Maximum of 400 MPN or CFU per 100 mL at... Coliform (2) (3) O&G (as HEM) 14 8.0 TSS 30 20 Total Nitrogen 147 103 1 mg/L (ppm). 2 Maximum of 400 MPN or...

Nitrogen and phosphorus removed from a subsurface flow multi-stage filtration system purifying agricultural runoff.

PubMed

Zhao, Yaqi; Huang, Lei; Chen, Yucheng

2018-07-01

Agricultural nonpoint source pollution has been increasingly serious in China since the 1990s. The main causes were excessive inputs of nitrogen fertilizer and pesticides. A multi-stage filtration system was built to test the purification efficiencies and removal characteristics of nitrogen and phosphorus when treating agricultural runoff. Simulated runoff pollution was prepared by using river water as source water based on the monitoring of local agricultural runoff. Experimental study had been performed from September to November 2013, adopting 12 h for flooding and 12 h for drying. The results showed that the system was made adaptive to variation of inflow quality and quantity, and had good removal for dissolved total nitrogen, total nitrogen, dissolved total phosphorus (DTP), and total phosphorus, and the average removal rate was 27%, 36%, 32%, and 48%, respectively. Except nitrate ([Formula: see text]), other forms of nitrogen and phosphorus all decreased with the increase of stages. Nitrogen was removed mainly in particle form the first stage, and mostly removed in dissolved form the second and third stage. Phosphorus was removed mainly in particulate during the first two stages, but the removal of particulate phosphorus and DTP were almost the same in the last stage. An approximate logarithmic relationship between removal loading and influent loading to nitrogen and phosphorus was noted in the experimental system, and the correlation coefficient was 0.78-0.94. [Formula: see text]: ammonium; [Formula: see text]: nitrite; [Formula: see text]: nitrate; DTN: dissolved total nitrogen; TN: total nitrogen; DTP: dissolved total phosphorus; TP: total phosphorus; PN: particulate nitrogen; PP: particulate phosphorus.

Microcrystalline sphalerite in resin globules suspended in Lake Kivu, East Africa

USGS Publications Warehouse

Degens, E.T.; Okada, H.; Honjo, S.; Hathaway, J.C.

1972-01-01

The origin and chemical nature of micron-sized spheres found as suspended particles in Lake Kivu are examined. It can be shown that the hollow spheres, with a wall thickness of 500 A??, consist of a complex polymeric resinous material which has little functionality, except for hydroxyl groups. The spheres arise in the process of degassing of water samples at depth. Tiny gas bubbles, about 1 micron in size, act as scavengers of dissolved resinous material. The newly created resinous membrane promotes the selective coordination of zinc dissolved in the water column. In the prevailing H2S regime, formation of sphalerite crystals in induced. The size range of the crystals, 5 to 50 A??, corresponds to 1 to 10 unit cells and suggests that the resinous membrane also acts as a template in sphalerite growth processes. The sources of the zinc and dissolved gases (CO2, CH4, H2S) are hydrothermal springs seeping from the lake bottom into the basin. Water discharge is substantial; about 100 years are required to fill the lake to its present level (ca. 550 km3 water). The average Kivu water contains 2 ppm zinc. Thus, 1 million tons of zinc are contained in Lake Kivu in the form of sphalerite. ?? 1972 Springer-Verlag.

Uncertainty analysis of the simulations of effects of discharging treated wastewater to the Red River of the North at Fargo, North Dakota, and Moorhead, Minnesota

USGS Publications Warehouse

Wesolowski, Edwin A.

1996-01-01

Two separate studies to simulate the effects of discharging treated wastewater to the Red River of the North at Fargo, North Dakota, and Moorhead, Minnesota, have been completed. In the first study, the Red River at Fargo Water-Quality Model was calibrated and verified for icefree conditions. In the second study, the Red River at Fargo Ice-Cover Water-Quality Model was verified for ice-cover conditions.To better understand and apply the Red River at Fargo Water-Quality Model and the Red River at Fargo Ice-Cover Water-Quality Model, the uncertainty associated with simulated constituent concentrations and property values was analyzed and quantified using the Enhanced Stream Water Quality Model-Uncertainty Analysis. The Monte Carlo simulation and first-order error analysis methods were used to analyze the uncertainty in simulated values for six constituents and properties at sites 5, 10, and 14 (upstream to downstream order). The constituents and properties analyzed for uncertainty are specific conductance, total organic nitrogen (reported as nitrogen), total ammonia (reported as nitrogen), total nitrite plus nitrate (reported as nitrogen), 5-day carbonaceous biochemical oxygen demand for ice-cover conditions and ultimate carbonaceous biochemical oxygen demand for ice-free conditions, and dissolved oxygen. Results are given in detail for both the ice-cover and ice-free conditions for specific conductance, total ammonia, and dissolved oxygen.The sensitivity and uncertainty of the simulated constituent concentrations and property values to input variables differ substantially between ice-cover and ice-free conditions. During ice-cover conditions, simulated specific-conductance values are most sensitive to the headwatersource specific-conductance values upstream of site 10 and the point-source specific-conductance values downstream of site 10. These headwater-source and point-source specific-conductance values also are the key sources of uncertainty. Simulated total ammonia concentrations are most sensitive to the point-source total ammonia concentrations at all three sites. Other input variables that contribute substantially to the variability of simulated total ammonia concentrations are the headwater-source total ammonia and the instream reaction coefficient for biological decay of total ammonia to total nitrite. Simulated dissolved-oxygen concentrations at all three sites are most sensitive to headwater-source dissolved-oxygen concentration. This input variable is the key source of variability for simulated dissolved-oxygen concentrations at sites 5 and 10. Headwatersource and point-source dissolved-oxygen concentrations are the key sources of variability for simulated dissolved-oxygen concentrations at site 14.During ice-free conditions, simulated specific-conductance values at all three sites are most sensitive to the headwater-source specific-conductance values. Headwater-source specificconductance values also are the key source of uncertainty. The input variables to which total ammonia and dissolved oxygen are most sensitive vary from site to site and may or may not correspond to the input variables that contribute the most to the variability. The input variables that contribute the most to the variability of simulated total ammonia concentrations are pointsource total ammonia, instream reaction coefficient for biological decay of total ammonia to total nitrite, and Manning's roughness coefficient. The input variables that contribute the most to the variability of simulated dissolved-oxygen concentrations are reaeration rate, sediment oxygen demand rate, and headwater-source algae as chlorophyll a.

Conduction disturbances after TAVR: Electrophysiological studies and pacemaker dependency.

PubMed

Makki, Nader; Dollery, Jenn; Jones, Danielle; Crestanello, Juan; Lilly, Scott

Permanent pacemaker (PPM) placement occurs in 5-20% of patients after transcatheter aortic valve replacement (TAVR). Although predictors of pacemaker implantation have been established, features that predispose patients to pacemaker utilization on follow up have not been widely reported. We performed a retrospective review of patients undergoing commercial TAVR between 2011 and 2016. We collated patients that underwent in-hospital PPM implantation and had a follow up of at least 3months. Data abstraction was performed for electrophysiological studies (EPS), pacemaker indication, timing, and device interrogation for pacemaker dependency on follow up. A total of 24 patients received in-hospital PPM post-TAVR (14% of total cohort), and mean follow up was 22months. Indications for PPM included resting complete heart block (CHB; 15/24, 63%), left bundle branch block and abnormal electrophysiological study (EPS; 7/24, 29%), alternating bundle branch block (1/24, 4%) and tachy-brady syndrome (1/24, 4%). Pacemaker dependency (underlying ventricular asystole, complete heart block, or >50% pacing) occurred in 8/24 patients (33%) during follow-up, 7 of whom had resting CHB, and one with CHB invoked during EPS. Pacemaker dependency after TAVR is common among those that exhibited CHB, but not among those with a prolonged HV delay during EPS. Although preliminary, these observations are relevant to management of rhythm disturbances after TAVR, and may inform the practice of EPS-based PPM implantation. Copyright © 2017 Elsevier Inc. All rights reserved.

Sediment PAHs and tumors in brown bullhead (Ameiurus nebulosus) at Featherstone National Wildlife Refuge, Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pinkney, A.E.; Sutherland, D.W.; Foley, R.E.

1995-12-31

Featherstone National Wildlife Refuge is located in Virginia along the Potomac River, about 35.4 kilometers southwest of Washington, DC. The study objective was to verify past observations of gross lesions in several fish species, previously collected from Potomac River tributaries for contaminant analysis. Thirty brown bullhead (Ameiurus nebulosus) were collected from Neabsco Creek, which borders the refuge, 29 were collected from Farm Creek, which bisects the refuge, and 30 were collected from Marumsco Creek, 1.75 km upstream. Sediment concentrations of polynuclear aromatic hydrocarbons (PAHS) were measured because elevated levels have been associated with skin and liver tumors in this species.more » The average concentration of total carcinogenic PAHs in sediments was: Farm Creek (0.34 ppm) < Marumsco Creek (0.63 ppm) < Neabsco Creek (1.37 ppm). The prevalence of skin neoplasms (squamous carcinomas and papillomas) was 3.4% in Farm Creek, 16.6% in Marumsco Creek, and 33.3% in Neabsco Creek. This ranking and the rankings of the total number of fish with tumors, invasive tumors, or non-parasitic lesions all followed the trend in sediment carcinogenic PAHs (p < 0.003; Jongheere-Terpstra test). The prevalence of liver carcinomas (O% at Farm Creek, 3.3% at Marumsco Creek, and 10% at Neabsco Creek) was of borderline significance (p = 0.06). The highest sediment concentrations of total (25.5 ppm) and carcinogenic (2.70 ppm) PAHs were found in Neabsco Creek near a complex of three marinas. Further sampling should be conducted in Neabsco Creek to determine the sources and extent of PAH contamination. Laboratory exposures are recommended for establishing a cause-effect linkage between sediment and tumor incidence. Additional sediment chemistry is needed to determine if other carcinogens are present.« less

Brain metabolic pattern analysis using a magnetic resonance spectra classification software in experimental stroke.

PubMed

Jiménez-Xarrié, Elena; Davila, Myriam; Candiota, Ana Paula; Delgado-Mederos, Raquel; Ortega-Martorell, Sandra; Julià-Sapé, Margarida; Arús, Carles; Martí-Fàbregas, Joan

2017-01-13

Magnetic resonance spectroscopy (MRS) provides non-invasive information about the metabolic pattern of the brain parenchyma in vivo. The SpectraClassifier software performs MRS pattern-recognition by determining the spectral features (metabolites) which can be used objectively to classify spectra. Our aim was to develop an Infarct Evolution Classifier and a Brain Regions Classifier in a rat model of focal ischemic stroke using SpectraClassifier. A total of 164 single-voxel proton spectra obtained with a 7 Tesla magnet at an echo time of 12 ms from non-infarcted parenchyma, subventricular zones and infarcted parenchyma were analyzed with SpectraClassifier ( http://gabrmn.uab.es/?q=sc ). The spectra corresponded to Sprague-Dawley rats (healthy rats, n = 7) and stroke rats at day 1 post-stroke (acute phase, n = 6 rats) and at days 7 ± 1 post-stroke (subacute phase, n = 14). In the Infarct Evolution Classifier, spectral features contributed by lactate + mobile lipids (1.33 ppm), total creatine (3.05 ppm) and mobile lipids (0.85 ppm) distinguished among non-infarcted parenchyma (100% sensitivity and 100% specificity), acute phase of infarct (100% sensitivity and 95% specificity) and subacute phase of infarct (78% sensitivity and 100% specificity). In the Brain Regions Classifier, spectral features contributed by myoinositol (3.62 ppm) and total creatine (3.04/3.05 ppm) distinguished among infarcted parenchyma (100% sensitivity and 98% specificity), non-infarcted parenchyma (84% sensitivity and 84% specificity) and subventricular zones (76% sensitivity and 93% specificity). SpectraClassifier identified candidate biomarkers for infarct evolution (mobile lipids accumulation) and different brain regions (myoinositol content).

Relationship between Escherichia coli virulence factors and postpartum metritis in dairy cows.

PubMed

Kassé, F N; Fairbrother, J M; Dubuc, J

2016-06-01

The objectives of this study were to report the prevalence of Escherichia coli and Trueperella pyogenes in the uterus of postpartum dairy cows before the onset of postpartum metritis (PPM) and to quantify their association with subsequent occurrence of PPM, to quantify the association between the presence of genes encoding E. coli virulence factors (VF) and PPM, and to determine the accuracy of using early postpartum uterine bacteriology results (bacteria and VF) to identify cows at risk of PPM. A prospective cohort study was conducted on 3 commercial dairy farms. Uterine swabs were collected from 371 Holstein dairy cows (3 commercial herds) at 1 to 7d in milk and submitted to the laboratory for identification of E. coli, T. pyogenes, and E. coli VF. A total of 40 VF were tested using the radioactive probe hybridization method. Postpartum metritis was defined as the presence of a fetid watery red-brown uterine discharge, associated with fever (rectal temperature >39.5°C), and systemic signs of illness (dullness, reduced appetite, and milk production). Surveillance of PPM was done by trained farmers blinded to laboratory results and cows were followed until 21d in milk. Statistical analyses were conducted using 2×2 tables and mixed logistical regression models. Prevalences of E. coli, T. pyogenes, and PPM were 42, 34, and 15%, respectively. A total of 32 VF were found in E. coli isolates. Most prevalent VF were extraintestinal pathogenic genes such as fimH (89%), hlyE (87%), and iss (70%). Cows positive for intrauterine E. coli were 3.2 times more likely to have subsequent PPM compared with bacteriologically negative cows. Cows with VF hra1 in their uterus were 2.7 times more likely to have PPM than cows positive for E. coli and negative for hra1 and 5.9 times more likely than bacteriologically negative cows. Cows with VF kpsMTII in their uterus were 3.2 times more likely to have PPM than cows positive for E. coli and negative for kpsMTII and 6.2 times more likely than bacteriologically negative cows. Using E. coli, hra1, and kpsMTII as predictors for subsequent PPM, positive predictive values were 23, 31, and 42%, respectively, whereas the negative predictive values were 91, 80, and 78%, respectively. Overall, these results showed that E. coli and some VF were associated with PPM. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effects of dietary selenium exposure in captive American common eiders

USGS Publications Warehouse

Franson, J.C.; Hoffman, D.J.; Wells-Berlin, A. M.; Perry, M.C.; Bochsler, V.S.; Finley, D.L.; Flint, Paul L.; Hollmen, T.

2005-01-01

We conducted two studies of Se exposure in captive common eiders (Somateria mollissima). In Study 1, eiders were fed diets with added Se (as L-selenomethionine) in concentrations increasing from 10 ppm to 80 ppm. In Study 2, eiders received control, low exposure (20 ppm Se), and high exposure (60 ppm Se) diets. One duck in the high exposure group in Study 2 died after 36 days. Remaining high exposure ducks in Study 2 and ducks in Study 1 were euthanized after losing 25-30% of their body weight, which occurred after 41 days and 60-78 days, respectively. Body weights did not differ between control and low exposure ducks in Study 2. At the end of Study 1, the mean Se concentration in blood was 32 ppm wet weight (ww). In Study 2, mean blood Se reached 14 ppm ww in the low exposure group and 17 ppm ww in high exposure ducks. Mean Se concentrations in liver were 1252 ppm dry weight (dw) in Study 1, and 351 and 735 ppm dw, respectively, in the low and high exposure groups of Study 2. Oxidative stress was evidenced by Se-associated effects on glutathione metabolism, but not entirely in the same manner as with previous laboratory studies in mallards. In plasma, activities of total and Se-dependent glutathione peroxidase increased with time. As Se concentrations in liver increased, Se-dependent glutathione peroxidase, glutathione reductase, oxidized glutathione, and the ratio of hepatic oxidized to reduced glutathione increased. Total and protein bound sulfhydryl concentrations, reduced glutathione, glutathione-S-transferase, and glucose-6-phosphate dehydrogenase in liver were negatively correlated with Se concentrations in the liver. In Study 2, spleen weights were significantly lower in ducks receiving 60 ppm Se than in those receiving 20 ppm. Gross lesions associated with high Se exposure included emaciation, absence of thymus, loss of nails from digits, and alopecia. Microscopic lesions included severe depletion of lymphoid organs, hepatopathy, and necrosis of feather pulp and feather epithelium. Common eiders fed high levels of Se lost weight and developed lesions similar to findings in experimental mallards, but they accumulated greater Se concentrations in tissues, particularly liver. Field studies have shown that apparently healthy seaducks generally have higher levels of Se in liver than healthy fresh water birds, but lower than the concentrations we found in our study. We conclude common eiders and probably other seaducks have a higher threshold, or adverse effect level, of Se in tissues than fresh water species.

Trends in selected water-quality characteristics, Flathead River at Flathead, British Columbia, and at Columbia Falls, Montana, water years, 1975-86

USGS Publications Warehouse

Cary, L.E.

1989-01-01

Data for selected water quality variables were evaluated for trends at two sampling stations--Flathead River at Flathead, British Columbia (Flathead station) and Flathead River at Columbia Falls, Montana (Columbia Falls station). The results were compared between stations. The analyses included data from water years 1975-86 at the Flathead station and water years 1979-86 at the Columbia Falls station. The seasonal Kendall test was applied to adjusted concentrations for variables related to discharge and to unadjusted concentrations for the remaining variables. Slope estimates were made for variables with significant trends unless data were reported as less than the detection limit. At the Flathead station, concentrations of dissolved solids, calcium, magnesium, sodium, dissolved nitrite plus nitrate nitrogen, ammonia nitrogen (total and dissolved), total organic nitrogen, and total phosphorus increased during the study period. Concentrations of total nitrite plus nitrate nitrogen and dissolved iron decreased during the same period. At the Columbia Falls station, concentrations increased for calcium and magnesium and decreased for sulfate and dissolved phosphorus. No trends were detected for 10 other variables tested at each station. Data for the Flathead station were reanalyzed for water years 1979-86. Trends in the data increased for magnesium and dissolved nitrite plus nitrate nitrogen and decreased for dissolved iron. Magnesium was the only variable that displayed a trend (increasing) at both stations. The increasing trends that were detected probably will not adversely affect the water quality of the Flathead River in the near future. (USGS)

Novel Apparatus for the Real-Time Quantification of Dissolved Gas Concentrations and Isotope Ratios

NASA Astrophysics Data System (ADS)

Gupta, M.; Leen, J.; Baer, D. S.; Owano, T. G.; Liem, J.

2013-12-01

Measurements of dissolved gases and their isotopic composition are critical in studying a variety of phenomena, including underwater greenhouse gas generation, air-surface exchange, and pollution migration. These studies typically involve obtaining water samples from streams, lakes, or ocean water and transporting them to a laboratory, where they are degased. The gases obtained are then generally measured using gas chromatography and isotope ratio mass spectrometry for concentrations and isotope ratios, respectively. This conventional, off-line methodology is time consuming, significantly limits the number of the samples that can be measured and thus severely inhibits detailed spatial and temporal mapping of gas concentrations and isotope ratios. In this work, we describe the development of a new membrane-based degassing device that interfaces directly to Los Gatos Research (cavity enhanced laser absorption or Off-Axis ICOS) gas analyzers (cavity enhanced laser absorption or Off-Axis ICOS analyzers) to create an autonomous system that can continuously and quickly measure concentrations and isotope ratios of dissolved gases in real time in the field. By accurately controlling the water flow rate through the membrane degasser, gas pressure on the outside of the membrane, and water pressure on the inside of the membrane, the system is able to generate precise and highly reproducible results. Moreover, by accurately measuring the gas flow rates in and out of the degasser, the gas-phase concentrations (ppm) could be converted into dissolved gas concentrations (nM). We will present detailed laboratory test data that quantifies the linearity, precision, and dynamic range of the system for the concentrations and isotope ratios of dissolved methane, carbon dioxide, and nitrous oxide. By interfacing the degassing device to a novel cavity-enhanced spectrometer (developed by LGR), preliminary data will also be presented for dissolved volatile organics (VOC) and other pollutants. Finally, the system was deployed shipboard, and field deployment data will also be presented.

Environmental assessment of NH3 injection for an industrial package boiler. Volume 2. Data supplement. Final report, January 1983-January 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaldini, C.; DeRosier, R.; Waterland, L.R.

1986-02-01

The report discusses emission results from comprehensive flue-gas sampling of a gas- and oil-fired industrial boiler equipped with Exxon's Thermal DeNOx Ammonia Injection Process for NOx reduction. Comprehensive emission measurements included continuous monitoring of flue gas emissions; source assessment sampling system (SASS) tests; EPA Method 5/17 for solid and condensible particulate emissions and ammonia emissions; controlled condensation system for SO2 and SO3; and N2O emission sampling. Ammonia injection at a NH3/NO molar ratio of 2.52 gave a NOx reduction of 41% from an uncontrolled level of 234 ppm to a controlled level of 137 ppm. NH3 emissions increased from 11more » ppm for the baseline to an average of 430 ppm for ammonia injection. Nitrous oxide, N2O, was reduced 68% from a 50 ppm baseline level to a 17 ppm controlled level. Total particulate emissions increased by an order of magnitude from a baseline of 17.7 ng/J to a controlled level of 182 ng/J.« less

Hair mercury concentrations and in vitro fertilization (IVF) outcomes among women from a fertility clinic.

PubMed

Wright, Diane L; Afeiche, Myriam C; Ehrlich, Shelley; Smith, Kristen; Williams, Paige L; Chavarro, Jorge E; Batsis, Maria; Toth, Thomas L; Hauser, Russ

2015-01-01

Total hair mercury (Hg) was measured among 205 women undergoing in vitro fertilization (IVF) treatment and the association with prospectively collected IVF outcomes (229 IVF cycles) was evaluated. Hair Hg levels (median=0.62ppm, range: 0.03-5.66ppm) correlated with fish intake (r=0.59), and exceeded the recommended EPA reference of 1ppm in 33% of women. Generalized linear mixed models with random intercepts accounting for within-woman correlations across treatment cycles were used to evaluate the association of hair Hg with IVF outcomes adjusted for age, body mass index, race, smoking status, infertility diagnosis, and protocol type. Hair Hg levels were not related to ovarian stimulation outcomes (peak estradiol levels, total and mature oocyte yields) or to fertilization rate, embryo quality, clinical pregnancy rate or live birth rate. Copyright © 2015 Elsevier Inc. All rights reserved.

Interactive effects of boron, selenium, and dietary protein on survival, growth and physiology in mallard ducklings

USGS Publications Warehouse

Hoffman, D.J.; Sanderson, C.J.; LeCaptain, L.J.; Cromartie, E.; Pendleton, G.W.

1991-01-01

High concentrations of boron (B) and selenium (Se) have been found in aquatic food chains associated with irrigation drainwater. Total biomass of invertebrates, a maJor source of protein for wild ducklings, is sometimes diminished in agricultural drainwater ponds contaminated with Se and B. Dayold mallard (Anas platyrhynchos) ducklings received an untreated diet (controls) containing 22% protein or diets containing 15 ppm (microgram/g) Se (as selenomethionine), 60 ppm Se, 1,000 ppm B (as boric acid), 15 ppm Se with 1,000 ppm B, or 60 ppm Se with 1,000 ppm B. In a concurrent experiment, the above sequence was repeated with a proteinrestricted (7%) but isocaloric diet. After four weeks, blood and tissue samples were collected for biochemical and histological examination. With 22% protein and 60 ppm Se in the diet, duckling survival and growth was reduced and histopathological lesions of the liver occurred. Boron alone caused some reduction in growth. Several interactive effects occurred between B and Se, including further reduction in growth, and increases in plasma glutathione reductase activity, hematocrit, hemoglobin and plasma protein concentrations. With 7% protein, the growth of controls was less than that with 22% protein, 60 ppm Se caused 100% mortality, and growth effects of 15 ppm Se and 1,000 ppm B alone were more pronounced than with 22% protein. Selenium accumulation increased in the liver with 7% protein. Interactive effects were greater for Se and B with 7% protein than with 22% protein and included significant mortality and enhanced accumulation of Se in the liver. These findings suggest the potential for more severe toxicological effects of Se and B independently and interactively on duckling survival and development when dietary protein is diminished.

Embryotoxic and teratogenic effects of selenium in the diet of mallards

USGS Publications Warehouse

Hoffman, D.J.; Heinz, G.H.

1988-01-01

Mallards (Anas platyrhynchos) were fed a control diet, diets containing 1, 5, 10, or 25 ppm Se as sodium selenite, or a diet containing 10 ppm Se as seleno-DL-methionine in the first of two experiments. Selenium at 10 ppm as selenomethionine or 25 ppm as sodium selenite caused a 40-44% decrease in the total number of eggs that hatched compared to controls. Selenium at 25 ppm (sodium selenite) resulted in a 19% decrease in mean embryonic weight at 18 d of incubation, accompanied by a 6% decrease in crown-rump length. Ten parts per million Se as selenomethionine was more teratogenic than sodium selenite at 25 ppm. Selenomethionine (10 ppm Se) resulted in an incidence of 13.1% malformations that were often multiple, whereas sodium selenite (10 and 25 ppm Se) resulted in 3.6 and 4.2% malformations. The teratogenicity of selenomethionine was confirmed in a second experiment in which mallards received 1, 2, 4, 8, or 16 ppm Se as selenomethionine, resulting in 0.9, 0.5, 1.4, 6.8, and 67.9% malformations, respectively. These malformations included hydrocephaly, microphthalmia, lower bill defects, and foot defects with ectrodactyly. Both forms of selenium increased the incidence of edema and stunted embryonic growth. Selenomethionine (10 ppm Se) resulted in a significant increase of approximately 40% in plasma glutathione peroxidase activity and a 70% increase in sorbitol dehydrogenase activity (indicative of hepatotoxicity) in hatchlings. Sodium selenite (25 ppm Se) resulted in fourfold elevation in plasma uric acid concentration, indicative of renal alteration. Selenomethionine accumulated much better in eggs than did sodium selenite. These findings indicate that selenomethionine is considerably more teratogenic and generally more embryotoxic than sodium selenite, probably due to higher uptake of selenomethionine.

Effects of elevated total dissolved solids on bivalves

EPA Science Inventory

A series of experiments were performed to assess the toxicity of different dominant salt recipes of excess total dissolved solids (TDS) to organisms in mesocosms. Multiple endpoints were measured across trophic levels. We report here the effects of four different TDS recipes on b...

COMMUNITY SCALE STREAM TAXA SENSITIVITIES TO DIFFERENT COMPOSITIONS OF EXCESS TOTAL DISSOLVED SOLIDS

EPA Science Inventory

Model stream chronic dosing studies (42 d) were conducted with three total dissolved solids (TDS) recipes. The recipes differed in composition of major ions. Community scale emergence was compared with single-species responses conducted simultaneously using the whole effluent tox...

Effectiveness of acidic oxidative potential water in preventing bacterial infection in islet transplantation.

PubMed

Miyamoto, M; Inoue, K; Gu, Y; Hoki, M; Haji, S; Ohyanagi, H

1999-01-01

At a number of points in the current procedures of islet isolation and islet culture after the harvesting of donor pancreata, microorganisms could potentially infect the islet preparation. Furthermore, the use of islets from multiple donors can compound the risks of contamination of individual recipients. Acidic oxidative potential water (also termed electrolyzed strong acid solution, function water, or acqua oxidation water), which was developed in Japan, is a strong acid formed on the anode in the electrolysis of water containing a small amount of sodium chloride. It has these physical properties: pH, from 2.3 to 2.7; oxidative-reduction potential, from 1,000 to 1,100 mV; dissolved chlorine, from 30 to 40 ppm; and dissolved oxygen, from 10 to 30 ppm. Because of these properties, acidic oxidative potential water has strong bactericidal effects on all bacteria including methicillin-resistant Staphylococcus aureus (MRSA), viruses including HIV, HBV, HCV, CMV, and fungi as a result of the action of the active oxygen and active chlorine that it contains. We conducted this study to evaluate the effect of acidic oxidative potential water irrigation on bacterial contamination on the harvesting of porcine pancreata from slaughterhouses for islet xenotransplantation by counting the number of pancreatic surface bacteria using the Dip-slide method, and on the results of islet culture; and to evaluate the direct effect on isolated islets when it is used to prevent bacterial contamination by the static incubation test and by morphological examination. Direct irrigation of the pancreas by acidic oxidative potential water was found to be very effective in preventing bacterial contamination, but direct irrigation of isolated islets slightly decreased their viability and function.

What makes hydromagmatic eruptions violent? Some insights from the Keanakāko'i Ash, Kı̄lauea Volcano, Hawai'i

USGS Publications Warehouse

Mastin, Larry G.; Christiansen, Robert L.; Thornber, Carl R.; Lowenstern, Jacob B.; Beeson, Melvin H.

2004-01-01

Volcanic eruptions at the summit of Ki??ilauea volcano, Hawai'i, are of two dramatically contrasting types: (1) benign lava flows and lava fountains; and (2) violent, mostly prehistoric eruptions that dispersed tephra over hundreds of square kilometers. The violence of the latter eruptions has been attributed to mixing of water and magma within a wet summit caldera; however, magma injection into water at other volcanoes does not consistently produce widespread tephras. To identify other factors that may have contributed to the violence of these eruptions, we sampled tephra from the Keanaka??ko'i Ash, the most recent large hydromagmatic deposit, and measured vesicularity, bubble-number density and dissolved volatile content of juvenile matrix glass to constrain magma ascent rate and degree of degassing at the time of quenching. Bubble-number densities (9 ?? 104- 1 ?? 107 cm-3) of tephra fragments exceed those of most historically erupted Ki??lauean tephras (3 ?? 103-1.8 ?? 105 cm-3), and suggest exceptionally high magma effusion rates. Dissolved sulfur (average = 330 ppm) and water (0.15-0.45 wt.%) concentrations exceed equilibrium-saturation values at 1 atm pressure (100-150 ppm and ???0.09%, respectively), suggesting that clasts quenched before equilibrating to atmospheric pressure. We interpret these results to suggest rapid magma injection into a wet crater, perhaps similar to continuous-uprush jets at Surtsey. Estimates of Reynolds number suggest that the erupting magma was turbulent and would have mixed with surrounding water in vortices ranging downward in size to centimeters. Such fine-scale mixing would have ensured rapid heat exchange and extensive magma fragmentation, maximizing the violence of these eruptions.

Inorganic geochemistry of domed peat in Indonesia and its implication for the origin of mineral matter in coal

USGS Publications Warehouse

Neuzil, Sandra G.; Supardi,; Cecil, C. Blaine; Kane, Jean S.; Soedjono, Kadar

1993-01-01

The inorganic geochemistry of three domed ombrogenous peat deposits in Riau and West Kalimantan provinces, Indonesia, was investigated as a possible modern analogue for certain types of low-ash, low-sulfur coal. Mineral matter entering the deposits is apparently limited to small amounts from the allogenic sources of dryfall, rainfall, and diffusion from substrate pore water. In the low-ash peat in the interior of the deposits, a large portion of the mineral matter is authigenic and has been mobilized and stabilized by hydrological, chemical, and biological processes and conditions.Ash yield and sulfur content are low through most of the peat deposits and average 1.1% and 0.14%, respectively, on a moisture-free basis. Ash and sulfur contents only exceed 5% and 0.3%, respectively, near the base of the deposits, with maximum concentrations of 19.9% ash and 0.56% sulfur. Peat water in all three deposits has a low pH, about 4 units, and low dissolved cation concentration, averaging 14 ppm. Near the base, in the geographic interior of each peat deposit, pH is about two units higher and dissolved cation concentration averages 110 ppm. Relative concentrations of the inorganic constituents vary, resulting in chemical facies in the peat. In general, Si, Al, and Fe are the abundant inorganic constituents, although Mg, Ca, and Na dominate in the middle horizon in the geographic interior of coastal peat deposits.The composition of the three deposits reported in this paper indicates that domed ombrogenous peat deposits will result in low ash and sulfur coal, probably less than 10% ash and 1% sulfur, even if marine rocks are laterally and vertically adjacent to the coal.

Simple and robust referencing system enables identification of dissolved-phase xenon spectral frequencies.

PubMed

Antonacci, Michael A; Zhang, Le; Burant, Alex; McCallister, Drew; Branca, Rosa T

2018-08-01

To assess the effect of macroscopic susceptibility gradients on the gas-phase referenced dissolved-phase 129 Xe (DPXe) chemical shift (CS) and to establish the robustness of a water-based referencing system for in vivo DPXe spectra. Frequency shifts induced by spatially varying magnetic susceptibility are calculated by finite-element analysis for the human head and chest. Their effect on traditional gas-phase referenced DPXe CS is then assessed theoretically and experimentally. A water-based referencing system for the DPXe resonances that uses the local water protons as reference is proposed and demonstrated in vivo in rats. Across the human brain, macroscopic susceptibility gradients can induce an apparent variation in the DPXe CS of up to 2.5 ppm. An additional frequency shift as large as 6.5 ppm can exist between DPXe and gas-phase resonances. By using nearby water protons as reference for the DPXe CS, the effect of macroscopic susceptibility gradients is eliminated and consistent CS values are obtained in vivo, regardless of shimming conditions, region of interest analyzed, animal orientation, or lung inflation. Combining in vitro and in vivo spectroscopic measurements finally enables confident assignment of some of the DPXe peaks observed in vivo. To use hyperpolarized xenon as a biological probe in tissues, the DPXe CS in specific organs/tissues must be reliably measured. When the gas-phase is used as reference, variable CS values are obtained for DPXe resonances. Reliable peak assignments in DPXe spectra can be obtained by using local water protons as reference. Magn Reson Med 80:431-441, 2018. © 2017 International Society for Magnetic Resonance in Medicine. © 2017 International Society for Magnetic Resonance in Medicine.

Carbonyl compounds emitted by a diesel engine fuelled with diesel and biodiesel-diesel blends: Sampling optimization and emissions profile

NASA Astrophysics Data System (ADS)

Guarieiro, Lílian Lefol Nani; Pereira, Pedro Afonso de Paula; Torres, Ednildo Andrade; da Rocha, Gisele Olimpio; de Andrade, Jailson B.

Biodiesel is emerging as a renewable fuel, hence becoming a promising alternative to fossil fuels. Biodiesel can form blends with diesel in any ratio, and thus could replace partially, or even totally, diesel fuel in diesel engines what would bring a number of environmental, economical and social advantages. Although a number of studies are available on regulated substances, there is a gap of studies on unregulated substances, such as carbonyl compounds, emitted during the combustion of biodiesel, biodiesel-diesel and/or ethanol-biodiesel-diesel blends. CC is a class of hazardous pollutants known to be participating in photochemical smog formation. In this work a comparison was carried out between the two most widely used CC collection methods: C18 cartridges coated with an acid solution of 2,4-dinitrophenylhydrazine (2,4-DNPH) and impinger bottles filled in 2,4-DNPH solution. Sampling optimization was performed using a 2 2 factorial design tool. Samples were collected from the exhaust emissions of a diesel engine with biodiesel and operated by a steady-state dynamometer. In the central body of factorial design, the average of the sum of CC concentrations collected using impingers was 33.2 ppmV but it was only 6.5 ppmV for C18 cartridges. In addition, the relative standard deviation (RSD) was 4% for impingers and 37% for C18 cartridges. Clearly, the impinger system is able to collect CC more efficiently, with lower error than the C18 cartridge system. Furthermore, propionaldehyde was nearly not sampled by C18 system at all. For these reasons, the impinger system was chosen in our study. The optimized sampling conditions applied throughout this study were: two serially connected impingers each containing 10 mL of 2,4-DNPH solution at a flow rate of 0.2 L min -1 during 5 min. A profile study of the C1-C4 vapor-phase carbonyl compound emissions was obtained from exhaust of pure diesel (B0), pure biodiesel (B100) and biodiesel-diesel mixtures (B2, B5, B10, B20, B50, B75). The ΣCC of the emission concentrations were 20.5 ppmV for B0 and 15.7 ppmV for B100. When considering fuel blends, the measured ΣCC were 21.4 ppmV, 22.5 ppmV, 20.4 ppmV, 14.2 ppmV, 11.4 ppmV and 14.7 ppmV, respectively, for B2, B5, B10, B20, B50 and B75. Among the target CC, both formaldehyde and acetaldehyde were the major contributors to the observed total CC levels. Except for acrolein and formaldehyde, all CC showed a clear trend of reduction in the emissions from B2 to B100 (40% reduction, on average). Both individual and total CC emission factors (pg g -1 of fuel burnt) were calculated for all tested biodiesel-diesel blends. The lowest total CC emission factor (2271 pg g -1) was found when B50 was used; the individual emission factors determined (pg g -1) were: 539.7 (formaldehyde), 1411 (acetaldehyde), 30.83 (acrolein), and 310.7 (propionaldehyde).

Use of Bioassay test for the environmental evaluation of mining residues and their leachates: the singular case of the Portman Bay (SE, Spain)

NASA Astrophysics Data System (ADS)

Martínez-Sánchez, Maria Jose; García-Lorenzo, Maria Luz; Pérez-Sirvent, Carmen; Molina, Jose; Tudela, Maria Luz; Hernández-Córdoba, Manuel

2010-05-01

The aim of the present study was to evaluate the toxicity of sediments and their pore-water extracts from sites contaminated by mining activities using two assays: bacteria and plants. The acute toxicity in pore-waters was determined using the Microtox® bioassay, which uses the naturally luminescent marine bacterium Vibrio fischeri. Phytotoxicity in soil samples was tested by way of the seed germination and root elongation technique in three plant species, Sorghum saccharatum, Sinapis alba and Lepidium sativum. The aim of applying these assays is to establish a method for evaluating the real risks within a risk analysis process, considering both present and future risks, bearing in mind that the uses to which soil is put (urban, recreational or industrial) may change. In the zone studied, mining activities have led to heavy metal contamination with the risk of runoff and wind dispersion of the contaminated material. For this study, 6 sediment samples were collected from Portman Bay (Murcia, SE Spain). The soil extract was prepared by saturation with distilled water and allowing it to stand for four hours. Then, the soil was subjected to a vacuum pressure to extract the soil solution through filter paper. The Zn and Fe content was determined by flame atomic absorption spectrometry (FAAS). The Pb, Cd and Cu content was determined by electrothermal atomization atomic absorption spectrometry (ETAAS). The As content was analysed by atomic fluorescence spectrometry using an automated continuous flow hydride generation (As-AFS) spectrometer. Total Pb concentration varied from 600 to 2500 ppm, with a mean value of 1200 ppm. The average content of Zn was 5300 ppm. The mean concentration of Cd and Cu was 23 and 59 ppm, respectively. Total As concentrations varied from 180 to 470 ppm, with an average value 280 ppm. Finally, the total Fe content ranged from 37% to 47%, with an average value of 40%. Pore-water samples showed neutral pH values and average electrical conductivity was 8.4 ds m-1. Mean heavy metal content in leachates from Portman Bay was 6.8 ppm for Pb, 0.1 ppm for Zn, 17 ppb for Cd, 5.6 ppb for Cu, 3.7 ppb for As and 0.6 ppm for Fe. The bioassays showed different sensitivities to the target metals. The Vibrio fischeri luminescence inhibition assay showed less sensitivity to the toxicants in the sediments than phytotoxicity assay. According to our results it is highly advisable to complement chemical analyses with environmental toxicity testing to characterise the risks presented by contaminated soils. Finally, these methods satisfy the requirements of environmental toxicology in their reliability, sensitivity, reproducibility, rapidity and low cost.

Mexicali aquifer and its relation with the Colorado river and the Cerro Prieto geothermal reservoir

NASA Astrophysics Data System (ADS)

Ramirez-Hernandez, J.; Reyes-Lopez, J. A.; Carreon-Diazconti, C.; Lazaro-Mancilla, O.

2008-05-01

Until some years ago the Colorado River has been the main recharge source of the Mexicali and the Imperial Valley aquifers. River discharge interruption after the constructions of dams upstream (i.e. Parker, Davis and Hoover) and the creation of great irrigation systems in both Valleys have modified their dynamics. Currently, the distribution of water recharge is the network of irrigation and drainage channels that distribute water to more than 500.000 ha. The chemical quality of the recharge water also has changed because the irrigation run-off water has become more mineralized. On the other hand, the intense steam exploitation of the Cerro Prieto geothermal reservoir has inverted the flow direction from the Volcano Lagoon area that until the 60s constituted the discharge zone of the aquifer and the geothermal reservoir. In this work, changes in the aquifer water recharge regime, the phreatic level and the water chemical quality are analyzed. It was found that after the reduction of the annual water extraction from aquifer up to 750X106 m3, the static levels have reached a dynamic balance that could be altered if water seepage from the irrigation channels, specially from the All American Channel, is reduced. The total dissolved solids (TDS) concentration has increased from 1000 ppm in 1970 to 1800 ppm in 2005. The water of recent infiltration, the gradual cooling of the shallowest strata of the geothermal reservoir, and the almost total disappearance of the hydrothermal surface manifestations are evidences of groundwater flow inversion. The new source of groundwater recharge due to seepage of evaporation disposal geothermal brine pond is documented. This pond incorporates water with a very different chemical composition to the groundwater system. Therefore, mineralization of the shallow aquifer layers and the soil contamination process are identified. It was concluded that the aquifer hydrodynamics in the Valley of Mexicali depends on the irrigation system more than on the Colorado River. The river has become a drainage channel to the Gulf of California.

Anthropogenic impacts on carbon uptake variability in the subtropical North Atlantic: 1992-2010

NASA Astrophysics Data System (ADS)

Tudino, Tobia; Messias, Marie-Jose; Mills, Benjamin J. W.; Watson, Andrew J.; Halloran, Paul R.; Bernardello, Raffaele; Torres-Valdés, Sinhue; Schuster, Ute; Williams, Richard G.; Wanninkhof, Rik

2017-04-01

Since 1860, anthropogenic emissions have increased atmospheric CO2 by more than 120ppm. The global ocean has lessened the accompanying climate impacts, taking up 33% of the emitted CO2, with the highest storage per unit area occurring in the North Atlantic. To investigate carbon uptake and storage in the subtropical North Atlantic, we compare three estimates of anthropogenic CO2 (Cant) with dissolved inorganic carbon (DIC) observations. We use data from a repeat (1992-2010) subtropical transect, where we find an average DIC increase of 1.06 μmol/(kg yr). We separate the observed DIC into five components: preindustrial, dissolved hard-tissue, regenerated soft-tissue, Cant, and surface air-sea disequilibrium. Among them, Cant increases approximately linearly over time (0.39-0.62 μmol/(kg yr), depending on the method adopted), contributing to the total DIC rise. Simultaneously, we observe a biologically driven increase (0.38 μmol/(kg yr)) in carbon from regenerated soft-tissue. We link this variation to the possible ongoing Atlantic meridional overturning circulation slow-down (2009-2010) and the associated strengthening of the biological pump. We expand our analysis by assessing outputs from an Earth system model between 1860 and 2100. In the preindustrial control (i.e. with no influence of anthropogenic CO2), we found a predominance of the biological pump in overall carbon uptake, while the industrial simulation leads to a comparable influence of the biological and physical pumps. We conclude that anthropogenic perturbation of the natural long-term variability in oceanic ventilation could affect the remineralized pool of carbon in the subtropical North Atlantic, potentially making it a higher sink for carbon than previously thought.

Electrochemistry of free chlorine and monochloramine and its relevance to the presence of Pb in drinking water.

PubMed

Rajasekharan, Vishnu V; Clark, Brandi N; Boonsalee, Sansanee; Switzer, Jay A

2007-06-15

The commonly used disinfectants in drinking water are free chlorine (in the form of HOCl/OCl-) and monochloramine (NH2Cl). While free chlorine reacts with natural organic matter in water to produce chlorinated hydrocarbon byproducts, there is also concern that NH2Cl may react with Pbto produce soluble Pb(II) products--leading to elevated Pb levels in drinking water. In this study, electrochemical methods are used to compare the thermodynamics and kinetics of the reduction of these two disinfectants. The standard reduction potential for NH2Cl/Cl- was estimated to be +1.45 V in acidic media and +0.74 V in alkaline media versus NHE using thermodynamic cycles. The kinetics of electroreduction of the two disinfectants was studied using an Au rotating disk electrode. The exchange current densities estimated from Koutecky-Levich plots were 8.2 x 10(-5) and 4.1 x 10(-5) A/cm2, and by low overpotential experiments were 7.5 +/- 0.3 x 10(-5) and 3.7 +/- 0.4 x 10(-5) A/cm2 for free chlorine and NH2Cl, respectively. The rate constantforthe electrochemical reduction of free chlorine at equilibrium is approximately twice as large as that for the reduction of NH2Cl. Equilibrium potential measurements show that free chlorine will oxidize Pb to PbO2 above pH 1.7, whereas NH2Cl will oxidize Pb to PbO2 only above about pH 9.5, if the total dissolved inorganic carbon (DIC) is 18 ppm. Hence, NH2Cl is not capable of producing a passivating PbO2 layer on Pb, and could lead to elevated levels of dissolved Pb in drinking water.

Reconnaissance of water-quality characteristics of streams in the City of Charlotte and Mecklenburg County, North Carolina

USGS Publications Warehouse

Eddins, W.H.; Crawford, J.K.

1984-01-01

In 1979-81, water samples were collected from 119 sites on streams throughout the City of Charlotte and Mecklenburg County, North Carolina, and were analyzed for specific conductance, dissolved chloride, hardness, pH, total alkalinity, total phosphorus, trace elements, arsenic, cadmium, chromium, copper, iron, lead, manganese, mercury, silver, and zinc and biological measures including dissolved oxygen, biochemical oxygen demand, fecal coliform bacteria, and fecal streptococcus bacteria. Sampling was conducted during both low flow (base flow) and high flow. Several water-quality measures including pH, total arsenic, total cadmium, total chromium, total copper, total iron, total lead, total manganese, total mercury, total silver, total zinc, dissolved oxygen, and fecal coliform bacteria at times exceeded North Carolina water-quality standards in various streams. Runoff from non-point sources appears to contribute more to the deterioration of streams in Charlotte and Mecklenburg County than point-source effluents. Urban and industrial areas contribute various trace elements. Residential and rural areas and municipal waste-water treatment plants contribute high amounts of phosphorus.

Compositional Data for Bengal Delta Sediment Collected from a Borehole at Rajoir, Bangladesh

USGS Publications Warehouse

Breit, George N.; Yount, James C.; Uddin, Md. Nehal; Muneem, Ad. Atual; Lowers, Heather; Berry, Cyrus J.; Whitney, John W.

2007-01-01

Processes active within sediment of the Bengal basin have attracted world concern because of the locally high content of arsenic dissolved in ground water drawn from that sediment. Sediment samples were collected from a borehole in the town of Rajoir, Rajoir upazila, Madaripur district, Bangladesh, to investigate the processes contributing to arsenic contamination. The samples were mineralogically and chemically analyzed to determine compositional variations related to the arsenic content of the sediment. Mineralogy of the sediment was determined using powder X-ray diffraction. Bulk chemical composition was measured by Combustion; Inductively Coupled Plasma Atomic Emission Spectroscopy; Energy Dispersive X-ray Fluorescence; and Hydride Generation Atomic Absorption Spectrophotometry. Sediment was treated with 0.5 N HCl and resulting solutions were analyzed, primarily to evaluate the abundance and oxidation state of acid-soluble iron. Acid-volatile sulfide, acid-soluble sulfate, and reducible sulfide were also measured on a few samples. Sediment sampled at Rajoir is typically unlithified, gray, micaceous, feldspathic arenaceous sand with a few silt and clay layers. Arsenic content of the sediment ranges from 0.6 to 21 ppm with a median of 1.2 ppm.

Multi-scale modeling of CO2 dispersion leaked from seafloor off the Japanese coast.

PubMed

Kano, Yuki; Sato, Toru; Kita, Jun; Hirabayashi, Shinichiro; Tabeta, Shigeru

2010-02-01

A numerical simulation was conducted to predict the change of pCO(2) in the ocean caused by CO(2) leaked from an underground aquifer, in which CO(2) is purposefully stored. The target space of the present model was the ocean above the seafloor. The behavior of CO(2) bubbles, their dissolution, and the advection-diffusion of dissolved CO(2) were numerically simulated. Here, two cases for the leakage rate were studied: an extreme case, 94,600 t/y, which assumed that a large fault accidentally connects the CO(2) reservoir and the seafloor; and a reasonable case, 3800 t/y, based on the seepage rate of an existing EOR site. In the extreme case, the calculated increase in DeltapCO(2) experienced by floating organisms was less than 300 ppm, while that for immobile organisms directly over the fault surface periodically exceeded 1000 ppm, if momentarily. In the reasonable case, the calculated DeltapCO(2) and pH were within the range of natural fluctuation. Copyright 2009 Elsevier Ltd. All rights reserved.

Elevated pCO2 enhances bacterioplankton removal of organic carbon

PubMed Central

James, Anna K.; Passow, Uta; Brzezinski, Mark A.; Parsons, Rachel J.; Trapani, Jennifer N.; Carlson, Craig A.

2017-01-01

Factors that affect the removal of organic carbon by heterotrophic bacterioplankton can impact the rate and magnitude of organic carbon loss in the ocean through the conversion of a portion of consumed organic carbon to CO2. Through enhanced rates of consumption, surface bacterioplankton communities can also reduce the amount of dissolved organic carbon (DOC) available for export from the surface ocean. The present study investigated the direct effects of elevated pCO2 on bacterioplankton removal of several forms of DOC ranging from glucose to complex phytoplankton exudate and lysate, and naturally occurring DOC. Elevated pCO2 (1000–1500 ppm) enhanced both the rate and magnitude of organic carbon removal by bacterioplankton communities compared to low (pre-industrial and ambient) pCO2 (250 –~400 ppm). The increased removal was largely due to enhanced respiration, rather than enhanced production of bacterioplankton biomass. The results suggest that elevated pCO2 can increase DOC consumption and decrease bacterioplankton growth efficiency, ultimately decreasing the amount of DOC available for vertical export and increasing the production of CO2 in the surface ocean. PMID:28257422

Water-quality data for Smith and Bybee Lakes, Portland, Oregon, June to November, 1982

USGS Publications Warehouse

Clifton, Daphne G.

1983-01-01

Water-quality monitoring at Smith and Bybee Lakes included measurement of water temperature, dissolved oxygen concentration and percent saturation, pH, specific conductance, lake depth, alkalinity, dissolved carbon, total dissolved solids, secchi disk light transparency, nutrients, and chlorophyll a and b. In addition, phytoplankton, zooplankton, and benthic invertebrate populations were identified and enumerated. Lakebed sediment was analyzed for particle size, volatile solids, immediate oxygen demand, trace metals, total organic carbon, nutrients, and organic constituents. (USGS)

Dissolved carbon biogeochemistry and export in mangrove-dominated rivers of the Florida Everglades

NASA Astrophysics Data System (ADS)

Ho, David T.; Ferrón, Sara; Engel, Victor C.; Anderson, William T.; Swart, Peter K.; Price, René M.; Barbero, Leticia

2017-05-01

The Shark and Harney rivers, located on the southwest coast of Florida, USA, originate in the freshwater, karstic marshes of the Everglades and flow through the largest contiguous mangrove forest in North America. In November 2010 and 2011, dissolved carbon source-sink dynamics was examined in these rivers during SF6 tracer release experiments. Approximately 80 % of the total dissolved carbon flux out of the Shark and Harney rivers during these experiments was in the form of inorganic carbon, either via air-water CO2 exchange or longitudinal flux of dissolved inorganic carbon (DIC) to the coastal ocean. Between 42 and 48 % of the total mangrove-derived DIC flux into the rivers was emitted to the atmosphere, with the remaining being discharged to the coastal ocean. Dissolved organic carbon (DOC) represented ca. 10 % of the total mangrove-derived dissolved carbon flux from the forests to the rivers. The sum of mangrove-derived DIC and DOC export from the forest to these rivers was estimated to be at least 18.9 to 24.5 mmol m-2 d-1, a rate lower than other independent estimates from Shark River and from other mangrove forests. Results from these experiments also suggest that in Shark and Harney rivers, mangrove contribution to the estuarine flux of dissolved carbon to the ocean is less than 10 %.

Liquid scintillation counting methodology for 99Tc analysis. A remedy for radiopharmaceutical waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khan, Mumtaz; Um, Wooyong

2015-08-13

This paper presents a new approach for liquid scintillation counting (LSC) analysis of single-radionuclide samples containing appreciable organic or inorganic quench. This work offers better analytical results than existing LSC methods for technetium-99 ( 99gTc) analysis with significant savings in analysis cost and time. The method was developed to quantify 99gTc in environmental liquid and urine samples using LSC. Method efficiency was measured in the presence of 1.9 to 11,900 ppm total dissolved solids. The quench curve was proved to be effective in the case of spiked 99gTc activity calculation for deionized water, tap water, groundwater, seawater, and urine samples.more » Counting efficiency was found to be 91.66% for Ultima Gold LLT (ULG-LLT) and Ultima Gold (ULG). Relative error in spiked 99gTc samples was ±3.98% in ULG and ULG-LLT cocktails. Minimum detectable activity was determined to be 25.3 mBq and 22.7 mBq for ULG-LLT and ULG cocktails, respectively. A pre-concentration factor of 1000 was achieved at 100°C for 100% chemical recovery.« less

Preparation and emission characteristics of ethanol-diesel fuel blends.

PubMed

Zhang, Run-Duo; He, Hong; Shi, Xiao-Yan; Zhang, Chang-Bin; He, Bang-Quan; Wang, Jian-Xin

2004-01-01

The preparation of ethanol-diesel fuel blends and their emission characteristics were investigated. Results showed the absolute ethanol can dissolve in diesel fuel at an arbitrary ratio and a small quantity of water(0.2%) addition can lead to the phase separation of blends. An organic additive was synthesized and it can develop the ability of resistance to water and maintain the stability of ethanol-diesel-trace amounts of water system. The emission characteristics of 10%, 20%, and 30% ethanol-diesel fuel blends, with or without additives, were compared with those of diesel fuel in a direct injection (DI) diesel engine. The experimental results indicated that the blend of ethanol with diesel fuel significantly reduced the concentrations of smoke, hydrocarbon (HC), and carbon monoxide (CO) in exhaust gas. Using 20% ethanol-diesel fuel blend with the additive of 2% of the total volume, the optimum mixing ratio was achieved, at which the bench diesel engine testing showed a significant decrease in exhaust gas. Bosch smoke number was reduced by 55%, HC emission by 70%, and CO emission by 45%, at 13 kW/1540 r/min. However, ethanol-diesel fuel blends produced a few ppm acetaldehydes and more ethanol in exhaust gas.

Trends in Streamflow and Nutrient and Suspended-Sediment Concentrations and Loads in the Upper Mississippi, Ohio, Red, and Great Lakes River Basins, 1975-2004

USGS Publications Warehouse

Lorenz, David L.; Robertson, Dale M.; Hall, David W.; Saad, David A.

2009-01-01

Many actions have been taken to reduce nutrient and suspended-sediment concentrations and the amount of nutrients and sediment transported in streams as a result of the Clean Water Act and subsequent regulations. This report assesses how nutrient and suspended-sediment concentrations and loads in selected streams have changed during recent years to determine if these actions have been successful. Flow-adjusted and overall trends in concentrations and trends in loads from 1993 to 2004 were computed for total nitrogen, dissolved ammonia, total organic nitrogen plus ammonia, dissolved nitrite plus nitrate, total phosphorus, dissolved phosphorus, total suspended material (total suspended solids or suspended sediment), and total suspended sediment for 49 sites in the Upper Mississippi, Ohio, Red, and Great Lakes Basins. Changes in total nitrogen, total phosphorus, and total suspended-material loads were examined from 1975 to 2003 at six sites to provide a longer term context for the data examined from 1993 to 2004. Flow-adjusted trends in total nitrogen concentrations at 19 of 24 sites showed tendency toward increasing concentrations, and overall trends in total nitrogen concentrations at 16 of the 24 sites showed a general tendency toward increasing concentrations. The trends in these flow-adjusted total nitrogen concentrations are related to the changes in fertilizer nitrogen applications. Flow-adjusted trends in dissolved ammonia concentrations from 1993 to 2004 showed a widespread tendency toward decreasing concentrations. The widespread, downward trends in dissolved ammonia concentrations indicate that some of the ammonia reduction goals of the Clean Water Act are being met. Flow-adjusted and overall trends in total organic plus ammonia nitrogen concentrations from 1993 to 2004 did not show a distinct spatial pattern. Flow-adjusted and overall trends in dissolved nitrite plus nitrate concentrations from 1993 to 2004 also did not show a distinct spatial pattern. Flow-adjusted trends in total phosphorus concentrations were upward at 24 of 40 sites. Overall trends in total phosphorus concentrations were mixed and showed no spatial pattern. Flow-adjusted and overall trends in dissolved phosphorus concentrations were consistently downward at all of the sites in the eastern part of the basins studied. The reduction in phosphorus fertilizer use and manure production east of the Mississippi River could explain most of the observed trends in dissolved phosphorus. Flow-adjusted trends in total suspended-material concentrations showed distinct spatial patterns of increasing tendencies throughout the western part of the basins studied and in Illinois and decreasing concentrations throughout most of Wisconsin, Iowa, and in the eastern part of the basins studied. Flow-adjusted trends in total phosphorus were strongly related to the flow-adjusted trends in suspended materials. The trends in the flow-adjusted suspended-sediment concentrations from 1993 to 2004 resembled those for suspended materials. The long-term, nonmonotonic trends in total nitrogen, total phosphorus, and suspended-material loads for 1975 to 2003 were described by local regression, LOESS, smoothing for six sites. The statistical significance of those trends cannot be determined; however, the long-term changes found for annual streamflow and load data indicate that the monotonic trends from 1993 to 2004 should not be extrapolated backward in time.

Effects of various timings and concentrations of inhaled nitric oxide in lung ischemia-reperfusion. The Paris-Sud University Lung Transplantation Group.

PubMed

Murakami, S; Bacha, E A; Mazmanian, G M; Détruit, H; Chapelier, A; Dartevelle, P; Hervé, P

1997-08-01

Experimental studies reveal that inhaled nitric oxide (NO) can prevent, worsen, or have no effect on lung injury in the setting of ischemia-reperfusion (I-R). We tested the hypothesis that these disparate effects could be related to differences in the timing of administration and/or concentration of inhaled NO during I-R. Isolated rat lungs were subjected to 1-h periods of ischemia followed by 1-h periods of blood reperfusion. We investigated the effects of NO (30 ppm) given during ischemia, NO (30 or 80 ppm) begun immediately at reperfusion, or NO (30 ppm) given 15 min after the beginning of reperfusion, on total pulmonary vascular resistance (PVR), the coefficient of filtration (Kfc), the lung wet/dry weight ratio (W/D) of lung tissue, and lung myeloperoxidase activity (MPO). A control group did not receive NO. NO given during ischemia had no effect on Kfc or MPO, but decreased PVR. NO (30 ppm) during reperfusion (early or delayed) decreased PVR, W/D, Kfc and MPO. NO at 80 ppm decreased PVR and MPO but not W/D or Kfc. In conclusion, NO at 30 ppm, given immediately or in a delayed fashion during reperfusion, attenuates I-R-induced lung injury. NO at 30 ppm given during ischemia or at 80 ppm during reperfusion is not protective.

THE RELATIONSHIP OF TOTAL DISSOLVED SOLIDS MEASUREMENTS TO BULK ELECTRICAL CONDUCTIVITY IN AN AQUIFER CONTAMINATED WITH HYDROCARBON

EPA Science Inventory

A recent conceptual model links high bulk electrical conductivities at hydrocarbon impacted sites to higher total dissolved solids (TDS) resulting from enhanced mineral weathering due to acids produced during biodegradation. In this study, we investigated the vertical distributio...

THE DETERMINATION OF TOTAL ORGANIC HALIDE IN WATER: A COMPARATIVE STUDY OF TWO INSTRUMENTS

EPA Science Inventory

Total organic halide (TOX) analyzers are commonly used to measure the amount of dissolved halogenated organic byproducts in disinfected waters. ecause of the lack of information on the identity of disinfection byproducts, rigorous testing of the dissolved organic halide (DOX) pro...

Flaxseed gum in combination with lemongrass essential oil as an effective edible coating for ready-to-eat pomegranate arils.

PubMed

Yousuf, Basharat; Srivastava, Abhaya Kumar

2017-11-01

Flaxseed gum (FSG) in combination with lemongrass essential oil (LGEO) was investigated for coating of ready-to-eat pomegranate arils. FSG was used at 0.3% and 0.6% concentrations and with both concentrations LGEO was incorporated at levels of 0ppm, 200ppm, 500ppm and 800ppm. Changes in headspace gases, physicochemical, microbiological and sensory attributes of pomegranate arils stored at 5°C were studied on different days of analysis during the 12day storage period. Coatings containing LGEO were effective in reducing total plate count and yeast and mold populations. Increasing LGEO concentrations in the coatings resulted in more decline in microbial populations. Reduced weight loss occurred in coated samples as compared to uncoated (control) sample. Coated samples showed a gradual decrease in ripening index in contrast with control where a significantly higher decline was observed. Total soluble solids, pH and titratable acidity significantly varied over the storage period. Color change (ΔE) for control increased steeply over the storage time in comparison to coated samples. Furthermore, chroma decreased while as hue angle increased over time. Copyright © 2017 Elsevier B.V. All rights reserved.

Laboratory measurements of selected optical, physical, chemical, and remote-sensing properties of five water mixtures containing Calvert clay and a nonfluorescing dye

NASA Technical Reports Server (NTRS)

Usry, J. W.; Whitlock, C. H.; Poole, L. R.; Witte, W. G., Jr.

1981-01-01

Total suspended solids concentrations ranged from 6.1 ppm to 24.3 ppm and sizes ranged between 1.5 micrometers and 10 micrometers with the most frequently occurring size less than 2 micrometers. Iron concentration was less than 1 percent of the total suspended solids. Nonfluorescing dye concentrations of the two mixtures were 20 ppm and 40 ppm. Attenuation coefficient for the five mixtures ranged from 4.8/m to 21.3/m. Variations in volume scattering function with phase angle were typical. Variations in attenuation and absorption coefficient with wavelength were similar for the mixtures without the dye. Attenuation coefficient of the mixtures with the dye increased for wavelengths less than 600 nm due to the dye's strong absorption peak near 500 nm. Reflectance increased as the concentration of Calvert clay increased and peaked near 600 nm. The nonfluorescent dye decreased the magnitude of the peak, but had practically no effect on the variation for wavelengths greater than 640 nm. At wavelengths less than 600 nm, the spectral variations of the mixtures with the dye were significantly different from those mixtures without the dye.

Trend analysis of selected water-quality constituents in the Verde River Basin, central Arizona

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baldys, S.

1990-01-01

Temporal trends of eight water quality constituents at six data collection sites in the Verde River basin in central Arizona were investigated using seasonal Kendall tau and ordinary least-squares regression methods of analysis. The constituents are dissolved solids, dissolved sulfate, dissolved arsenic, total phosphorus, pH, total nitrite plus nitrate-nitrogen, dissolved iron, and fecal coliform bacteria. Increasing trends with time in dissolved-solids concentrations of 7 to 8 mg/L/yr at Verde River near Camp Verde were found at significant level. An increasing trend in dissolved-sulfate concentrations of 3.59 mg/L/yr was also found at Verde River near Camp Verde, although at nonsignificant levels.more » Statistically significant decreasing trends with time in dissolved-solids and dissolved-sulfate concentrations were found at Verde River above Horseshoe Reservoir, which is downstream from Verde River near Camp Verde. Observed trends in the other constituents do not indicate the emergence of water quality problems in the Verde River basin. Analysis of the eight water quality constituents generally indicate nonvarying concentration levels after adjustment for seasonality and streamflow were made.« less

A SURROGATE SUBCHRONIC TOXICITY TEST METHOD FOR WATERS WITH HIGH TOTAL DISSOLVED SOLIDS

EPA Science Inventory

Total dissolved solids (TDS) are often identified as a toxicant in whole-effluent toxicity (WET) testing. The primary test organism used in WET testing, Ceriodaphnia dubia, is very sensitive to TDS ions, which can be problematic when differentiating the toxicity of TDS from those...

THE DETERMINATION OF TOTAL ORGANIC HALIDE IN WATER: AN INTERLABORATORY COMPARATIVE STUDY OF TWO METHODS

EPA Science Inventory

Total organic halide (TOX) analyzers are commonly used to measure the amount of dissolved halogenated organic byproducts in disinfected waters. Because of the lack of information on the identity of disinfection byproducts, rigorous testing of the dissolved organic halide (DOX) pr...

Community-Level Effects of Excess Total Dissolved Solids Doses Using Model Streams

EPA Science Inventory

Model stream chronic dosing studies (42 days) were conducted with four different total dissolved solids (TDS) recipes. The recipes differed in their relative dominance of major ions. One was made from sodium and calcium chloride salts only. Another was similar to the first, but a...

TOTAL DISSOLVED AND BIOAVAILABLE METALS AT LAKE TEXOMA MARINAS

EPA Science Inventory

Dissolved metals in water and total metals in sediments have been measured at marina areas in Lake Texoma during June 1999 to October 2001, and October 2001, respectively. The metals most often found in the highest concentrations in marina water were Na and Ca, followed by Mg an...

Reduced carbonic fluid at magmatic PT conditions: new experimental data.

NASA Astrophysics Data System (ADS)

Simakin, Alexander; Salova, Tamara; Rinat, Gabitov; Sergey, Isaenko

2017-04-01

We study properties of the dry fluid of C-O-S composition at P=2000 bar and T=900-1000oC. Dry carbonic fluid was generated at the thermal decomposition of FeCO3 and (Fe,Mg)CO3. At the decomposition of pure FeCO3 assemblages of Wus-Mt and pure Mt was recognized. Wus-Mt corresponds to the fO2 on the level around QFM-2. Native carbon was formed from the fluid when CO concentration was above constrained by CCO buffer. Generated fluid was trapped as the bubbles within welded albite glass matrix. Micro-Raman study yields around 15 vol.% of CO in the mixture with CO2. The glass trap composition was interpreted to estimate the minimum solubilities of different elements in the studied fluid: Pt - 15 ppm, Mn - 262 ppm, P - 4100 ppm, Ce -22 ppm, S- 3400 ppm, Sr - 3300 ppm (Simakin et al., 2016). We add sulfur to the system in the form of FeS2, thermally decomposing after carbonates. Fluid interaction with platinum capsule walls to form PtS leads to the fast removal of sulfur. Analysis of the interaction products provides preliminary estimate of the Pt solubility. We observe transformation of magnetite to FeS at the reaction with COS. Pyrrhotite formed from oxide contains in average 1.5 wt.% of Pt. Assuming that at the reaction 1/3Fe3O4+COS+1/3CO = FeS +CO2 all dissolved in the fluid platinum was incorporated into the sulfide we get minimum Pt solubility of about 5000 ppm. To capture fluid composition we perform experiments in the Au capsules with sodium-silicate glass trap. Micro-Raman shows that presence of water in sodium-silicate leads to the partial COS decomposition to thiols and H2S, however, COS still was prevailing form of sulfur in the fluid as predicted theoretically (Simakin, 2014). Transport of siderophile (Ni, Cr, PGE, Au), LILE (Ba, Cs, Rb, Sr), LREE and chalcophile (Ag, Zn, Cu) elements by the dry fluid of C-O-S composition can be decisive during the formation of different volcanic aerosol phases. Study was partially supported by RFBR-DFG grant # 16-55-12040. References. Simakin AG, Salova TP, Gabitov RI and Isaenko SI. Dry CO2-CO fluid as an important potential deep Earth solvent. Geofluids (2016, online). Simakin AG (2014) Peculiarities of the fluid composition in the dry C-O-S system at PT parameters of the low crust by the data of the thermodynamic modeling. Petrology, 22, 50-59.

Evaluation of larvicidal activity of Acalypha alnifolia Klein ex Willd. (Euphorbiaceae) leaf extract against the malarial vector, Anopheles stephensi, dengue vector, Aedes aegypti and Bancroftian filariasis vector, Culex quinquefasciatus (Diptera: Culicidae).

PubMed

Kovendan, Kalimuthu; Murugan, Kadarkarai; Vincent, Savariar

2012-02-01

The leaf extract of Acalypha alnifolia with different solvents - hexane, chloroform, ethyl acetate, acetone and methanol - were tested for larvicidal activity against three important mosquitoes such as malarial vector, Anopheles stephensi, dengue vector, Aedes aegypti and Bancroftian filariasis vector, Culex quinquefasciatus. The medicinal plants were collected from the area around Kallar Hills near the Western Ghats, Coimbatore, India. A. alnifolia plant was washed with tap water and shade dried at room temperature. The dried leaves were powdered mechanically using commercial electrical stainless steel blender. The powder 800 g of the leaf material was extract with 2.5 litre of various each organic solvents such as hexane, chloroform, ethyl acetate, acetone, methanol for 8 h using Soxhlet apparatus, and filtered. The crude plant extracts were evaporated to dryness in a rotary vacuum evaporator. The yield of extracts was hexane (8.64 g), chloroform (10.74 g), ethyl acetate (9.14 g), acetone (10.02 g), and methanol (11.43 g). One gram of the each plant residue was dissolved separately in 100 ml of acetone (stock solution) from which different concentrations, i.e., 50, 150, 250, 350 and 450 ppm, was prepared. The hexane, chloroform, ethyl acetate, acetone was moderate considerable mortality; however, the highest larval mortality was methanolic extract observed in three mosquito vectors. The larval mortality was observed after 24 h exposure. No mortality was observed in the control. The early fourth-instar larvae of A. stephensi had values of LC(50) = 197.37, 178.75, 164.34, 149.90 and 125.73 ppm and LC(90) = 477.60, 459.21, 435.07, 416.20 and 395.50 ppm, respectively. The A. aegypti had values of LC(50) = 202.15, 182.58, 160.35, 146.07 and 128.55 ppm and LC(90) = 476.57, 460.83, 440.78, 415.38 and 381.67 ppm, respectively. The C. quinquefasciatus had values of LC(50) = 198.79, 172.48, 151.06, 140.69 and 127.98 ppm and LC(90) = 458.73, 430.66, 418.78, 408.83 and 386.26 ppm, respectively. The results of the leaf extract of A. alnifloia are promising as good larvicidal activity against the mosquito vector, A. stephensi, A. aegypti, C. quinquefasciatus. Therefore, this study provides first report on the larvicidal activities against three species of mosquito vectors of this plant extracts from Southern India.

Emission of diacetyl (2,3 butanedione) from natural butter, microwave popcorn butter flavor powder, paste, and liquid products.

PubMed

Rigler, Mark W; Longo, William E

2010-01-01

Diacetyl (2,3 butanedione), a butter-flavored diketone, has been linked to a severe lung disease, bronchiolitis obliterans. We tested a total of three natural butters and artificial microwave popcorn butter flavorings (three powders, two pastes, and one liquid) for bulk diacetyl concentration and diacetyl emissions when heated. Pastes and liquid butter flavors contained the highest amount (6% to 10.6%) while natural butter possessed up to 7500 times less diacetyl. All artificial butter flavors studied emitted diacetyl. Dry powders emitted up to 1.62 ppm diacetyl; wetted powders up to 54.7 ppm diacetyl; and pastes emitted up to 34.9 ppm diacetyl. The liquid butter flavor emitted up to 17.2 ppm diacetyl. Microwave popcorn flavoring mixtures emitted up to 11.4 ppm diacetyl. At least 93% of the dry powder particles were inhalable. These studies show that microwave butter flavoring products generate concentrations of diacetyl in the air great enough to endanger those exposed.

Effects of aflatoxin and carotenoids on growth performance and immune response in mule ducklings.

PubMed

Cheng, Y H; Shen, T F; Pang, V F; Chen, B J

2001-01-01

The purpose of this study was to investigate if carotenoids could alleviate the adverse effects caused by aflatoxin with respect to growth performance and immune response. In two experiments, a total of 320 mule ducklings were assigned to 5 treatments, i.e. control, aflatoxin B(1) (AFB(1)) 200 ppb, AFB(1) +beta-carotene (BC) 200 ppm, AFB(1)+BC 400 ppm, and AFB(1)+astaxanthin (AS) 200 ppm. In experiment 1, the addition of beta-carotene or astaxanthin in the diet containing AFB(1) 200 ppb resulted in a significant decrease in average daily gain as compared with the control. AFB(1) 200 ppb alone and the addition of BC or AS on top of AFB(1) resulted in a significantly lower daily feed intake than for the control group. There were no significant differences in relative organ weights among treatment groups. Both treatments of BC 400 ppm and AS 200 ppm had significantly more macrophages harvested per duck than the control and AFB(1) 200 ppb treatments. However, there were no significant differences among treatments in percentages of phagocytotic macrophages and number of Candida albican phagocytized by phagocytotic macrophages. In experiment 2, blood biochemical parameters and antibody titers were evaluated. There were no significant differences among treatments in total bilirubin content and alkaline phosphatase activity in the serum or in antibody titers against fowl cholera. However, AFB(1) treatment had the highest activities of AST and ALT in the serum. The addition of BC 400 ppm on top of AFB(1) significantly reduced ALT activity as compared with the AFB(1) 200 ppb treatment. These results suggest that carotenoids could provide a slightly toxic alleviating effect on growth performance, enhance the chemotaxis ability of macrophages, and reduce ALT activity elevated by AFB(1).

Analytical Results for 42 Fluvial Tailings Cores and 7 Stream Sediment Samples from High Ore Creek, Northern Jefferson County, Montana

USGS Publications Warehouse

Fey, David L.; Church, Stan E.

1998-01-01

Metal-mining related wastes in the Boulder River basin study area in northern Jefferson County, Montana have been implicated in their detrimental effects on water quality with regard to acid-generation and toxic-metal solubility. Sediments, fluvial tailings and water from High Ore Creek have been identified as significant contributors to water quality degradation of the Boulder River below Basin, Montana. A study of 42 fluvial tailings cores and 7 stream sediments from High Ore Creek was undertaken to determine the concentrations of environmentally sensitive elements (i.e. Ag, As, Cd, Cu, Pb, Zn) present in these materials, and the mineral phases containing those elements. Two sites of fluvial deposition of mine-waste contaminated sediment on upper High Ore Creek were sampled using a one-inch soil probe. Forty-two core samples were taken producing 247 subsamples. The samples were analyzed by ICP-AES (inductively coupled-plasma atomic emission spectroscopy) using a total mixed-acid digestion. Results of the core analyses show that the elements described above are present at very high concentrations (to 22,000 ppm As, to 460 ppm Ag, to 900 ppm Cd, 4,300 ppm Cu, 46,000ppm Pb, and 50,000 ppm Zn). Seven stream-sediment samples were also analyzed by ICP-AES for total element content and for leachable element content. Results show that the sediment of High Ore Creek has elevated levels of ore-related metals throughout its length, down to the confluence with the Boulder River, and that the metals are, to a significant degree, contained in the leachable phase, namely the hydrous amorphous iron- and manganese-hydroxide coatings on detrital sediment particles.

Environmental setting of benchmark streams in agricultural areas of eastern Wisconsin

USGS Publications Warehouse

Rheaume, S.J.; Stewart, J.S.; Lenz, B.N.

1996-01-01

Differences in land use/land cover, and riparian vegetation and instream habitat characteristics are presented. Summaries of field measurements of water temperature, pH, specific conductance and concentrations of dissolved oxygen, total organic plus ammonia nitrogen, dissolved ammonium, nitrate plus nitrte as nitrogen, total phosphorus, dissolved orthophosphate, and atrazine are listed. Concentrations of dissolved oxygen for the sampled streams ranged from 6 A to 14.3 and met the standards set by the Wisconsin Department of Natural Resources (WDNR) for supporting fish and aquatic life. Specific conductance ranged from 98 to 753 u,Scm with values highest in RHU's 1 and 3, where streams are underlain by carbonate bedrock. Median pH did not vary greatly among the four RHU's and ranged from 6.7 to 8.8 also meeting the WDNR standards. Concentrations of total organic plus ammonia nitrogen, dissolved ammonium, total phosphorus, and dissolved orthophosphate show little variation between streams and are generally low, compared to concentrations measured in agriculturally-affected streams in the same RHU's during the same sampling period. Concentrations of the most commonly used pesticide in the study unit, atrazine, were low in all streams, and most concentrations were below trn 0.1 u,g/L detection limit. Riparian vegetation for the benchmark streams were characterized by lowland species of the native plant communities described by John T. Curtis in the "Vegetation of Wisconsin." Based on the environmental setting and water-quality information collected to date, these streams appear to show minimal adverse effects from human activity.

[Release and supplement of carbon, nitrogen and phosphorus from jellyfish (Nemopilema nomurai) decomposition in seawater].

PubMed

Qu, Chang-feng; Song, Jin-ming; Li, Ning; Li, Xue-gang; Yuan, Hua-mao; Duan, Li-qin

2016-01-01

Abstract: Jellyfish bloom has been increasing in Chinese seas and decomposition after jellyfish bloom has great influences on marine ecological environment. We conducted the incubation of Nemopilema nomurai decomposing to evaluate its effect on carbon, nitrogen and phosphorus recycling of water column by simulated experiments. The results showed that the processes of jellyfish decomposing represented a fast release of biogenic elements, and the release of carbon, nitrogen and phosphorus reached the maximum at the beginning of jellyfish decomposing. The release of biogenic elements from jellyfish decomposition was dominated by dissolved matter, which had a much higher level than particulate matter. The highest net release rates of dissolved organic carbon and particulate organic carbon reached (103.77 ± 12.60) and (1.52 ± 0.37) mg · kg⁻¹ · h⁻¹, respectively. The dissolved nitrogen was dominated by NH₄⁺-N during the whole incubation time, accounting for 69.6%-91.6% of total dissolved nitrogen, whereas the dissolved phosphorus was dominated by dissolved organic phosphorus during the initial stage of decomposition, being 63.9%-86.7% of total dissolved phosphorus and dominated by PO₄³⁻-P during the late stage of decomposition, being 50.4%-60.2%. On the contrary, the particulate nitrogen was mainly in particulate organic nitrogen, accounting for (88.6 ± 6.9) % of total particulate nitrogen, whereas the particulate phosphorus was mainly in particulate. inorganic phosphorus, accounting for (73.9 ±10.5) % of total particulate phosphorus. In addition, jellyfish decomposition decreased the C/N and increased the N/P of water column. These indicated that jellyfish decomposition could result in relative high carbon and nitrogen loads.

Seasonal variability of total dissolved fluxes and origin of major dissolved elements within a large tropical river: The Orinoco, Venezuela

NASA Astrophysics Data System (ADS)

Laraque, Alain; Moquet, Jean-Sébastien; Alkattan, Rana; Steiger, Johannes; Mora, Abrahan; Adèle, Georges; Castellanos, Bartolo; Lagane, Christèle; Lopez, José Luis; Perez, Jesus; Rodriguez, Militza; Rosales, Judith

2013-07-01

Seasonal variations of total dissolved fluxes of the lower Orinoco River were calculated taking into account four complete hydrological cycles during a five-year period (2005-2010). The modern concentrations of total dissolved solids (TDS) of the Orinoco surface waters were compared with data collected during the second half of the last century published in the literature. This comparison leads to the conclusion that chemical composition did not evolve significantly at least over the last thirty to forty years. Surface waters of the Orinoco at Ciudad Bolivar are between bicarbonated calcic and bicarbonated mixed. In comparison to mean values of concentrations of total dissolved solids (TDS) of world river surface waters (89.2 mg l-1), the Orinoco River at Ciudad Bolivar presents mainly low mineralized surface waters (2005-10: TDS 30 mg l-1). The TDS fluxes passing at this station in direction to the Atlantic Ocean between 2005 and 2010 were estimated at 30 × 106 t yr-1, i.e. 36 t km-2 yr-1. It was observed that the seasonal variations (dry season vs wet season) of total dissolved fluxes (TDS and dissolved organic carbon (DOC)) are mainly controlled by discharge variations. Two groups of elements have been defined from dilution curves and molar ratio diagrams. Ca2+, Mg2+, HCO3-, Cl- and Na+ mainly come from the same geographic and lithologic area, the Andes. K+ and SiO2 essentially come from the Llanos and the Guayana Shield. These findings are important for understanding fundamental geochemical processes within the Orinoco River basin, but also as a baseline study in the perspective of the development of numerous mining activities related with aluminum and steel industries; and the plans of the Venezuelan government to construct new fluvial ports on the lower Orinoco for the transport of hydrocarbons.

Metal dispersion and mobility in soils from the Lik Zn-Pb-Ag massive sulphide deposit, NW Alaska: Environmental and exploration implications

USGS Publications Warehouse

Kelley, K.D.; Kelley, D.L.

2003-01-01

The Lik deposit in northern Alaska is a largely unexposed shale-hosted Zn-Pb-Ag massive sulphide deposit that is underlain by continuous permafrost. Residual soils overlying the mineralized zone have element enrichments that are two to six times greater than baseline values. The most prominent elements are Ag, Mo, P, Se, Sr, V by total 4-acid digestion and Tl by a weak partial digestion (Enzyme Leach or EL) because they show multi-point anomalies that extend across the entire mineralized zone, concentration ranges are 0.5-2.6 ppm Ag, 4-26 ppm Mo, 0.1-0.3% P, 3-22 ppm Se, 90-230 ppm Sr, 170-406 ppm V, and 1.6-30 ppb Tl. Lead, Sb, and Hg are also anomalous (up to 178 ppm, 30 ppm, and 1.9 ppm, respectively), but all are characterized by single point anomalies directly over the mineralized zone, with only slightly elevated concentrations over the lower mineralized section. Zinc (total) has a consistent baseline response of 200 ppm, but it is not elevated in soils overlying the mineralized zone. However, Zn by EL shows a distinct single-point anomaly over the ore zone that suggests it was highly mobile and partly adsorbed on oxides or other secondary phases during weathering. In situ analyses (by laser ablation ICP-MS) of pyrite and sphalerite from drill core suggest that sphalerite is the primary residence for Ag, Cd, and Hg in addition to Zn, and pyrite contains As, Fe, Sb, and Tl. The level and degree of oxidation, and the proportion of reacting pyrite and carbonate minerals are two factors that affected the mobility and transport of metals. In oxidizing conditions, Zn is highly mobile relative to Hg and Ag, perhaps explaining the decoupling of Zn from the other sphalerite-hosted elements in the soils. Soils are acidic (to 3.9 pH) directly over the deposit due to the presence of acid-producing pyrite, but acid-neutralizing carbonate away from the mineralized zone yield soils that are near neutral. The soils therefore formed in a complex system involving oxidation and weathering (mechanical and chemical) of sulphide minerals, dissolution of carbonate minerals, and precipitation of iron and manganese oxide minerals.

Overstory vegetation influence nitrogen and dissolved organic carbon flux from the atmosphere to the forest floor: Boreal Plain, Canada

Treesearch

David E. Pelster; Randall K. Kolka; Ellie E. Prepas

2009-01-01

Nitrate, ammonium, total dissolved nitrogen (TDN), dissolved organic nitrogen (DON) and dissolved organic carbon (DOC) concentrations and flux were measured for one year in bulk deposition and throughfall from three stand types (upland deciduous, upland conifer and wetland conifer) on the Boreal Plain, Canada. Annual (November 2006 to October 2007 water year) flux...

Thermophilic aerobic digestion process for producing animal nutrients and other digested products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coulthard, T.L.; Townsley, P.M.; Saben, H.S.

1981-09-29

Waste materials are digested by thermophilic bacteria to produce single-cell protein and vitamin B12. The bacteria are contained in the waste and are not inoculated. Thus, a hog manure slurry containing 10% solids was stirred with aeration in an insulated reactor to allow the temperature to be maintained at greater than 55/sup 0/. The temperature was maintained at 55-65/sup 0/ and the dissolved O/sub 2/ concentration at 1.5-3 ppm for 6 days. After 10 days reaction, the product was fed to hogs as 10% of their nutrient supply with no apparent adverse effects.

Ionic liquids as advantageous solvents for headspace gas chromatography of compounds with low vapor pressure.

PubMed

Andre, M; Loidl, J; Laus, G; Schottenberger, H; Bentivoglio, G; Wurst, K; Ongania, K-H

2005-01-15

The potential of ionic liquids as solvents for headspace gas chromatography was investigated. Three compounds with boiling points above 200 degrees C were selected to demonstrate the feasibility of the concept described. 2-Ethylhexanoic acid, formamide, and tri-n-butylamine as examples of acidic, neutral, and basic analytes were dissolved in acidic 1-n-butyl-3-methylimidazolium hydrogen sulfate (1), neutral 1-n-butyl-2,3-dimethylimidazolium dicyanamide (2), and 2 containing 1,8-diazabicyclo[5.4.0]undec-7-ene to adjust basic conditions. All analytes could be determined with limits of detection and limits of quantification in the low-ppm concentration range.

Accumulation of Fe oxyhydroxides in the Peruvian oxygen deficient zone implies non-oxygen dependent Fe oxidation

DOE PAGES

Heller, Maija I.; Lam, Phoebe J.; Moffett, James W.; ...

2017-05-19

Oxygen minimum zones (OMZs) have been proposed to be an important source of dissolved iron (Fe) into the interior ocean. However, previous studies in OMZs have shown a sharp decrease in total dissolved Fe (dFe) and/or dissolved Fe(II) (dFe(II)) concentrations at the shelf-break, despite constant temperature, salinity and continued lack of oxygen across the shelf-break. The loss of both total dFe and dFe(II) suggests a conversion of the dFe to particulate form, but studies that have coupled the reduction-oxidation (redox) speciation of both dissolved and particulate phases have not previously been done. Here in this work, we have measured themore » redox speciation and concentrations of both dissolved and particulate forms of Fe in samples collected during the U.S. GEOTRACES Eastern tropical Pacific Zonal Transect (EPZT) cruise in 2013 (GP16). This complete data set allows us to assess possible mechanisms for loss of dFe. We observed an offshore loss of dFe(II) within the oxygen deficient zone (ODZ), where dissolved oxygen is undetectable, accompanied by an increase in total particulate Fe (pFe). Total pFe concentrations were highest in the upper ODZ. X-ray absorption spectroscopy revealed that the pFe maximum was primarily in the Fe(III) form as Fe(III) oxyhydroxides. The remarkable similarity in the distributions of total particulate iron and nitrite suggests a role for nitrite in the oxidation of dFe(II) to pFe(III). Lastly, we present a conceptual model for the rapid redox cycling of Fe that occurs in ODZs, despite the absence of oxygen.« less

Accumulation of Fe oxyhydroxides in the Peruvian oxygen deficient zone implies non-oxygen dependent Fe oxidation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heller, Maija I.; Lam, Phoebe J.; Moffett, James W.

Oxygen minimum zones (OMZs) have been proposed to be an important source of dissolved iron (Fe) into the interior ocean. However, previous studies in OMZs have shown a sharp decrease in total dissolved Fe (dFe) and/or dissolved Fe(II) (dFe(II)) concentrations at the shelf-break, despite constant temperature, salinity and continued lack of oxygen across the shelf-break. The loss of both total dFe and dFe(II) suggests a conversion of the dFe to particulate form, but studies that have coupled the reduction-oxidation (redox) speciation of both dissolved and particulate phases have not previously been done. Here in this work, we have measured themore » redox speciation and concentrations of both dissolved and particulate forms of Fe in samples collected during the U.S. GEOTRACES Eastern tropical Pacific Zonal Transect (EPZT) cruise in 2013 (GP16). This complete data set allows us to assess possible mechanisms for loss of dFe. We observed an offshore loss of dFe(II) within the oxygen deficient zone (ODZ), where dissolved oxygen is undetectable, accompanied by an increase in total particulate Fe (pFe). Total pFe concentrations were highest in the upper ODZ. X-ray absorption spectroscopy revealed that the pFe maximum was primarily in the Fe(III) form as Fe(III) oxyhydroxides. The remarkable similarity in the distributions of total particulate iron and nitrite suggests a role for nitrite in the oxidation of dFe(II) to pFe(III). Lastly, we present a conceptual model for the rapid redox cycling of Fe that occurs in ODZs, despite the absence of oxygen.« less

Accumulation of Fe oxyhydroxides in the Peruvian oxygen deficient zone implies non-oxygen dependent Fe oxidation

NASA Astrophysics Data System (ADS)

Heller, Maija I.; Lam, Phoebe J.; Moffett, James W.; Till, Claire P.; Lee, Jong-Mi; Toner, Brandy M.; Marcus, Matthew A.

2017-08-01

Oxygen minimum zones (OMZs) have been proposed to be an important source of dissolved iron (Fe) into the interior ocean. However, previous studies in OMZs have shown a sharp decrease in total dissolved Fe (dFe) and/or dissolved Fe(II) (dFe(II)) concentrations at the shelf-break, despite constant temperature, salinity and continued lack of oxygen across the shelf-break. The loss of both total dFe and dFe(II) suggests a conversion of the dFe to particulate form, but studies that have coupled the reduction-oxidation (redox) speciation of both dissolved and particulate phases have not previously been done. Here we have measured the redox speciation and concentrations of both dissolved and particulate forms of Fe in samples collected during the U.S. GEOTRACES Eastern tropical Pacific Zonal Transect (EPZT) cruise in 2013 (GP16). This complete data set allows us to assess possible mechanisms for loss of dFe. We observed an offshore loss of dFe(II) within the oxygen deficient zone (ODZ), where dissolved oxygen is undetectable, accompanied by an increase in total particulate Fe (pFe). Total pFe concentrations were highest in the upper ODZ. X-ray absorption spectroscopy revealed that the pFe maximum was primarily in the Fe(III) form as Fe(III) oxyhydroxides. The remarkable similarity in the distributions of total particulate iron and nitrite suggests a role for nitrite in the oxidation of dFe(II) to pFe(III). We present a conceptual model for the rapid redox cycling of Fe that occurs in ODZs, despite the absence of oxygen.

Concentrations, loads, and yields of nutrients and suspended sediment in the South Pacolet, North Pacolet, and Pacolet Rivers, northern South Carolina and southwestern North Carolina, October 2005 to September 2009

USGS Publications Warehouse

Journey, Celeste A.; Caldwell, Andral W.; Feaster, Toby D.; Petkewich, Mattew D.; Bradley, Paul M.

2011-01-01

The U.S. Geological Survey, in cooperation with Spartanburg Water, evaluated the concentrations, loads, and yields of suspended sediment, dissolved ammonia, dissolved nitrate plus nitrite, total organic nitrogen, total nitrogen, dissolved orthophosphate, dissolved phosphorus, and total phosphorus at sites in the South Pacolet, North Pacolet, and Pacolet Rivers in northern South Carolina and southwestern North Carolina from October 1, 2005, to September 30, 2009 (water years 2006 to 2009). Nutrient and sediment loads and yields also were computed for the intervening subbasin of the Pacolet River not represented by the South and North Pacolet River Basins. Except for a few outliers, the majority of the measurements of total nitrogen concentrations were well below the U.S. Environmental Protection Agency recommended guideline of 0.69 milligram per liter for streams and rivers in the nutrient ecoregion IX, which includes the study area within the Pacolet River Basin. Dissolved orthophosphate, dissolved phosphorus, and total phosphorus concentrations were significantly lower at the South Pacolet River site compared to the North Pacolet and Pacolet River sites. About 90 percent of the total phosphorus concentrations at the South Pacolet River site were below the U.S. Environmental Protection Agency recommended guideline of 0.37 milligram per liter, and more than 75 percent of the total phosphorus concentrations at the North Pacolet and Pacolet River sites were above that guideline. At all sites, minimum annual nutrient loads for the estimation period were observed during water year 2008 when severe drought conditions were present. An estimated mean annual total nitrogen load of 37,770 kilograms per year and yield of 2.63 kilograms per hectare per year were determined for the South Pacolet River site for the estimation period. The North Pacolet River site had a mean annual total nitrogen load of 65,890 kilograms per year and yield of 2.19 kilograms per hectare per year. The Pacolet River had a mean annual total nitrogen load of 99,780 kilograms per year and yield of 1.82 kilograms per hectare per year. Mean annual total phosphorus loads of 2,576; 9,404; and 11,710 kilograms per year and yields of 0.180, 0.313, and 0.213 kilograms per hectare per year were estimated at the South Pacolet, North Pacolet, and Pacolet River sites, respectively. Annually, the intervening subbasin of the Pacolet River contributed negligible amounts of total nitrogen and total phosphorus loads, and large losses of dissolved nitrate plus nitrite and orthophosphate loads were determined for the subbasin. Biological (algal) uptake in the two reservoirs in this intervening area was considered the likely explanation for the loss of these constituents. Estimated mean annual suspended-sediment loads were 21,190,000; 9,895,000; and 6,547,000 kilograms per year at the South Pacolet, North Pacolet, and Pacolet River sites, respectively. In the intervening Pacolet River subbasin, computed annual suspended-sediment loads were consistently negative, indicating large percentage losses in annual suspended-sediment load. Sedimentation processes in the two reservoirs are the most likely explanations for these apparent losses. At all sites, the winter season tended to have the highest estimated seasonal dissolved orthophosphate and dissolved nitrate plus nitrite fluxes, and the summer and fall seasons tended to have the lowest fluxes. The reverse pattern, however, was observed in the intervening drainage area in the Pacolet River where the lowest fluxes of dissolved orthophosphate and nitrate plus nitrite occurred during the winter and spring seasons and the highest occurred during the summer and fall seasons. Synoptic samples were collected during a high-flow event in August 2009 at eight sites that represented shoreline and minor tributary drainages. The South Pacolet River site was identified as contributing greater than 80 percent of the cumulative nutrient and sediment l

Effects of a single inhalative exposure to formaldehyde on the open field behavior of mice.

PubMed

Malek, Fathi A; Möritz, Klaus-Uwe; Fanghänel, Jochen

2004-02-01

The effects of formaldehyde on the explorative behavior and locomotor activity of mice after a single inhalative exposure were examined in an open field. Adult male mice were exposed to approximately 1.1 ppm, 2.3 ppm, or 5.2 ppm formaldehyde vapour for 2 hours and the open field test was carried out two hours after the end of exposure (trial 1) and repeated 24 hours thereafter (trial 2). The following behavioral parameters were quantitatively examined: numbers of crossed floor squares (inner, peripheral, total), sniffing, grooming, rearing, climbing, and incidence of fecal boli. The results of the first trial revealed that the motion activity was significantly reduced in all exposed groups. In the 1.1 ppm group, the frequency of rearing was reduced and that of floor sniffing increased. The exposure to the two higher formaldehyde concentrations caused a significant decrease in total numbers of floor squares crossed by the subjects, air sniffing, and rearing. The open field test on the next day (trial 2) showed that the frequencies of floor sniffing, grooming, and rearing in all formaldehyde groups were significantly altered. In the 2.5 ppm group, an increased incidence of fecal boli was observed. From the results obtained, we conclude that the exposure of male mice to formaldehyde vapour affects their locomotor and explorative activity in the open field, and that some open field parameters are still altered in the exposed animals even after 24 hours.

Effects of dietary zinc supplementation on hen performance, ammonia volatilization, and nitrogen retention in manure.

PubMed

Kim, W K; Patterson, P H

2005-01-01

This investigation was undertaken to evaluate the effects of dietary ZnSO4 supplementation on ammonia volatilization and nitrogen retention in hen manure. One hundred twenty, 45-wk-old commercial Leghorn laying hens were sequentially fed diets with 1000, 2000, and 3000 ppm Zn as ZnSO4 (Zn-1000, Zn-2000, and Zn-3000), then followed by two control dietary periods with 114 ppm Zn (Control-1 and Control-2) for a total of five consecutive eight-day experiment periods, respectively. When hens were fed the 1000 and 2000 ppm Zn treatment diets, room ammonia levels were significantly reduced compared to the control diets. Dietary Zn treatments reduced the decomposition of uric acid, resulting in an increase in manure total-N retention compared to the control fed birds. The 1000 ppm Zn supplement had no adverse effects on hen body weight, feed consumption, egg production, egg weight, albumen height, or shell thickness. However, hens fed the diet containing 3000 ppm Zn had significantly depressed body weight, feed consumption, egg production, egg weight, and shell thickness. Zinc levels of egg contents increased linearly as dietary Zn levels increased. These levels in eggs would not be a problem for human consumption because these are much less than the daily Zn recommended dietary allowance. Although land application of such manure will not cause environmental problems or crop toxicity, proper monitoring of soil and crop Zn levels and effective nutrient management planning would be well advised.

Antitumor effects of nano-bubble hydrogen-dissolved water are enhanced by coexistent platinum colloid and the combined hyperthermia with apoptosis-like cell death.

PubMed

Asada, Ryoko; Kageyama, Katsuhiro; Tanaka, Hiroshi; Matsui, Hisakazu; Kimura, Masatsugu; Saitoh, Yasukazu; Miwa, Nobuhiko

2010-12-01

In order to erase reactive oxygen species (ROS) related with the proliferation of tumor cells by reducing activity of hydrogen, we developed functional water containing nano-bubbles (diameters: <900 nm for 71%/population) hydrogen of 1.1-1.5 ppm (the theoretical maximum: 1.6 ppm) with a reducing ability (an oxidation-reduction potential -650 mV, normal water: +100-200 mV) using a microporous-filter hydrogen-jetting device. We showed that hydrogen water erased ROS indispensable for tumor cell growth by ESR/spin trap, the redox indicator CDCFH-DA assay, and was cytotoxic to Ehrlich ascites tumor cells as assessed by WST-8 assay, crystal violet dye stain and scanning electron microscopy, after 24-h or 48-h incubation sequent to warming at 37°C or 42°C. Hydrogen water supplemented with platinum colloid (0.3 ppm Pt in 4% polyvinylpyrrolidone) had more antitumor activity than hydrogen water alone, mineral water alone (15.6%), hydrogen water plus mineral water, or platinum colloid alone as observed by decreased cell numbers, cell shrinkage and pycnosis (nuclear condensation)/karyorrhexis (nuclear fragmentation) indicative of apoptosis, together with cell deformation and disappearance of microvilli on the membrane surface. These antitumor effects were promoted by combination with hyperthermia at 42°C. Thus, the nano-bubble hydrogen water with platinum colloid is potent as an anti-tumor agent.

Accurate MR thermometry by hyperpolarized 129 Xe.

PubMed

Zhang, Le; Burant, Alex; McCallister, Andrew; Zhao, Victor; Koshlap, Karl M; Degan, Simone; Antonacci, Michael; Branca, Rosa Tamara

2017-09-01

To investigate the temperature dependence of the resonance frequency of lipid-dissolved xenon (LDX) and to assess the accuracy of LDX-based MR thermometry. The chemical shift temperature dependence of water protons, methylene protons, and LDX was measured from samples containing tissues with varying fat contents using a high-resolution NMR spectrometer. LDX results were then used to acquire relative and absolute temperature maps in vivo and the results were compared with PRF-based MR thermometry. The temperature dependence of proton resonance frequency (PRF) is strongly affected by the specific distribution of water and fat. A redistribution of water and fat compartments can reduce the apparent temperature dependence of the water chemical shift from -0.01 ppm/°C to -0.006 ppm, whereas the LDX chemical shift shows a consistent temperature dependence of -0.21 ppm/°C. The use of the methylene protons resonance frequency as internal reference improves the accuracy of LDX-based MR thermometry, but degrades that of PRF-based MR thermometry, as microscopic susceptibility gradients affected lipid and water spins differently. The LDX resonance frequency, with its higher temperature dependence, provides more accurate and precise temperature measurements, both in vitro and in vivo. More importantly, the resonance frequency of nearby methylene protons can be used to extract absolute temperature information. Magn Reson Med 78:1070-1079, 2017. © 2016 International Society for Magnetic Resonance in Medicine. © 2016 International Society for Magnetic Resonance in Medicine.

The effects of exercise on dose and dose distribution of inhaled automotive pollutants.

PubMed

Kleinman, M T; Mautz, W J

1991-10-01

The purpose of this study was to determine how changes in ventilation rate and in the entry route of air pollutants into the respiratory tract (nose versus mouth breathing) affected the respiratory tract uptake and penetration of inhaled gaseous and particulate pollutants associated with automobile emissions. Experiments were performed with female beagle dogs exposed while standing at rest or while exercising on a treadmill at 5 km/hour and a 7.5 percent grade. Dogs were exposed to nitrogen dioxide at concentrations of 1 and 5 parts per million (ppm), to formaldehyde at 2 and 10 ppm, and to an aerosol of ammonium nitrate particles (0.3 micron mass median aerodynamic diameter) at 1 mg/m3. Total respiratory system uptake and effects on breath time, expired tidal volume, fractional expiration time, minute ventilation, respiratory gas exchange, ventilation equivalents for oxygen and carbon dioxide, and dynamic pulmonary resistance and compliance were measured in exercising and resting dogs exposed for two hours to 5 ppm nitrogen dioxide and 10 ppm formaldehyde in combination with 1 mg/m3 of ammonium nitrate particles. Regional penetration of pollutants through oral and nasal airways and pollutant uptake in the lung were measured in a separate group of six tracheostomized dogs standing at rest while being exposed to nitrogen dioxide, formaldehyde, and ammonium nitrate particles. Hypercapnic stimulation was used to modify ventilation rates in the tracheostomized dogs while pollutant penetration and uptake were measured. Dogs exposed to 5 ppm of nitrogen dioxide at rest tended to breathe more rapidly (p less than 0.05) and more shallowly (a nonsignificant trend) than dogs exposed to purified air. The changes observed were similar in direction, but of smaller magnitude, to changes observed when the same dogs were exposed during exercise to ozone at 0.6 ppm in a separate study. Rapid-shallow breathing was not observed when the dogs were exposed during exercise to 5 ppm nitrogen dioxide. Dogs exposed to a mixture of 10 ppm formaldehyde and 1 mg/m3 ammonium nitrate particles during exercise showed a shift to larger tidal volume breathing, but the response was much less pronounced than the slow-deep breathing pattern response observed in a separate study of dogs exposed to 10 ppm formaldehyde alone. The total respiratory system uptake of formaldehyde from the formaldehyde and ammonium nitrate mixture was larger than that measured for 10 ppm of formaldehyde alone in another exercise and exposure study.(ABSTRACT TRUNCATED AT 400 WORDS)

Settling characteristics of nursery pig manure and nutrient estimation by the hydrometer method.

PubMed

Zhu, Jun; Ndegwa, Pius M; Zhang, Zhijian

2003-05-01

The hydrometer method to measure manure specific gravity and subsequently relate it to manure nutrient contents was examined in this study. It was found that this method might be improved in estimation accuracy if only manure from a single growth stage of pigs was used (e.g., nursery pig manure used here). The total solids (TS) content of the test manure was well correlated with the total nitrogen (TN) and total phosphorus (TP) concentrations in the manure, with highly significant correlation coefficients of 0.9944 and 0.9873, respectively. Also observed were good linear correlations between the TN and TP contents and the manure specific gravity (correlation coefficients: 0.9836 and 0.9843, respectively). These correlations were much better than those reported by past researchers, in which lumped data for pigs at different growing stages were used. It may therefore be inferred that developing different linear equations for pigs at different ages should improve the accuracy in manure nutrient estimation using a hydrometer. Also, the error of using the hydrometer method to estimate manure TN and TP was found to increase, from +/- 10% to +/- 50%, with the decrease in TN (from 700 ppm to 100 ppm) and TP (from 130 ppm to 30 ppm) concentrations in the manure. The estimation errors for TN and TP may be larger than 50% if the total solids content is below 0.5%. In addition, the rapid settling of solids has long been considered characteristic of swine manure; however, in this study, the solids settling property appeared to be quite poor for nursery pig manure in that no conspicuous settling occurred after the manure was left statically for 5 hours. This information has not been reported elsewhere in the literature and may need further research to verify.

The influence of groundwater chemistry on arsenic concentrations and speciation in a quartz sand and gravel aquifer

USGS Publications Warehouse

Kent, D.B.; Fox, P.M.

2004-01-01

We examined the chemical reactions influencing dissolved concentrations, speciation, and transport of naturally occurring arsenic (As) in a shallow, sand and gravel aquifer with distinct geochemical zones resulting from land disposal of dilute sewage effluent. The principal geochemical zones were: (1) the uncontaminated zone above the sewage plume [350 ??M dissolved oxygen (DO), pH 5.9]; (2) the suboxic zone (5 ??M DO, pH 6.2, elevated concentrations of sewage-derived phosphate and nitrate); and (3) the anoxic zone [dissolved iron(II) 100-300 ??M, pH 6.5-6.9, elevated concentrations of sewage-derived phosphate]. Sediments are comprised of greater than 90% quartz but the surfaces of quartz and other mineral grains are coated with nanometer-size iron (Fe) and aluminum (Al) oxides and/or silicates, which control the adsorption properties of the sediments. Uncontaminated groundwater with added phosphate (620 ??M) was pumped into the uncontaminated zone while samples were collected 0.3 m above the injection point. Concentrations of As(V) increased from below detection (0.005 ??M) to a maximum of 0.07 ??M during breakthrough of phosphate at the sampling port; As(III) concentrations remained below detection. These results are consistent with the hypothesis that naturally occurring As(V) adsorbed to constituents of the coatings on grain surfaces was desorbed by phosphate in the injected groundwater. Also consistent with this hypothesis, vertical profiles of groundwater chemistry measured prior to the tracer test showed that dissolved As(V) concentrations increased along with dissolved phosphate from below detection in the uncontaminated zone to approximately 0.07 and 70 ??M, respectively, in the suboxic zone. Concentrations of As(III) were below detection in both zones. The anoxic zone had approximately 0.07 ??M As(V) but also had As(III) concentrations of 0.07-0.14 ??M, suggesting that release of As bound to sediment grains occurred by desorption by phosphate, reductive dissolution of Fe oxides, and reduction of As(V) to As(III), which adsorbs only weakly to the Fe-oxide-depleted material in the coatings. Results of reductive extractions of the sediments suggest that As associated with the coatings was relatively uniformly distributed at approximately 1 nmol/g of sediment (equivalent to 0.075 ppm As) and comprised 20%-50% of the total As in the sediments, determined from oxidative extractions. Quartz sand aquifers provide high-quality drinking water but can become contaminated when naturally occurring arsenic bound to Fe and Al oxides or silicates on sediment surfaces is released by desorption and dissolution of Fe oxides in response to changing chemical conditions. ?? 2004 American Institute of Physics.

Developmental toxicity study in Sprague-Dawley rats by whole-body exposure to N,N-diethylethanolamine vapor.

PubMed

Leung, H W; Murphy, S R

1998-01-01

Timed-pregnant Sprague-Dawley rats were exposed whole body to N,N-diethylethanolamine vapor for 6 h per day on gestational days (GD) 6-15 at targeted concentrations of 33, 66 or 100 ppm. Dams were sacrificed on GD 21. There was no maternal mortality in any exposed groups. Maternal toxicity observed in the 100 ppm group included dry rales, reduced body weight (9.5%) on GD 15 and reduced weight gain (48%) during exposure. Suppression of body weight gain was also noted in the 66 ppm group during GD 12-15. There were no effects of treatment on gestational parameters, including pre- and post-implantation loss or sex ratio. Mean fetal body weights in treated groups were comparable to controls. There was no increase in the incidence of total malformations (external, visceral or skeletal) or individually by category. The incidence of a single developmental variation (hypoplastic bones of the forepaw) in the 100 ppm groups was statistically significantly decreased relative to that of controls. The no-observed-adverse-effect level was 33 ppm for maternal toxicity but greater than 100 ppm for embryofetal toxicity and teratogenicity.

Evaluation of Total Dissolved Solids and Specific Conductance Water Quality Targets with Paired Single-Species and Mesocosm Community Exposures

EPA Science Inventory

Isolated single-species exposures were conducted in parallel with 42 d mesocosm dosing studies that measured in-situ and whole community responses to different recipes of excess total dissolved solids (TDS). The studies were conducted with cultured species and native taxa from mo...

Bench-Scale and Pilot-Scale Treatment Technologies for the Removal of Total Dissolved Solids from Coal Mine Water: A Review

EPA Science Inventory

Coal mine water (CMW) is typically treated to remove suspended solids, acidity, and soluble metals, but high concentrations of total dissolved solids (TDS) have been reported to impact the environment at several CMW discharge points. Consequently, various states have establishe...

Comparing Single species Toxicity Tests to Mesocosm Community-Level Responses to Total Dissolved Solids Comprised of Different Major Ions

EPA Science Inventory

Total Dissolved Solids (TDS) dosing studies representing different sources of ions were conducted from 2011-2015. Emergence responses in stream mesocosms were compared to single-species exposures using a whole effluent testing (WET) format and an ex-situ method (single species te...

The impact of diets with different magnesium contents on magnesium and calcium in serum and tissues of the rat.

PubMed

Zimmermann, P; Weiss, U; Classen, H G; Wendt, B; Epple, A; Zollner, H; Temmel, W; Weger, M; Porta, S

2000-07-14

The impact of three different magnesium diets (70, 1,000 and 9,000 ppm) on total, ionized and bound magnesium as well as ionized calcium in serum and total calcium and magnesium in femoral bone, skeletal muscle, heart and liver of male Sprague-Dawley rats was investigated. The percentage of ionized serum magnesium was unproportionally high in rats fed a low magnesium (70 ppm) diet. Femoral magnesium was correlated with ionized and total serum magnesium. In contrast, there was generally no correlation between total serum magnesium and the magnesium fractions in skeletal muscle, heart and liver. In rats fed the magnesium deficient diet, total cardiac concentration of magnesium was even significantly increased along with total calcium content, while there were no effects on total muscle and liver magnesium. Within the single groups, ionized serum calcium was never proportional to dietary magnesium, but in all three magnesium diet groups together, it was inversely correlated with dietary magnesium. Moreover, ionized serum calcium was inversely correlated with both ionized and total serum magnesium. In all 3 groups together, the concentrations of total calcium and magnesium in heart and skeletal muscle were correlated, within the single groups correlation existed only in the 1000 ppm group. Magnesium influx via calcium channels during low magnesium intake has been seen in non cardiac tissues [35,36], but nothing similar is known about non selective channels for divalent cations in the heart [33]. Thus, magnesium uptake by cardiac cells along with calcium seems to be possible, especially at low intracellular magnesium concentrations, but is still poorly investigated. We suggest that the calcium-antagonistic effect of magnesium is related to the turnover rate of magnesium rather than to its tissue concentrations.

Quality of major ion and total dissolved solids data from groundwater sampled by the National Water-Quality Assessment Program, 1992–2010

USGS Publications Warehouse

Gross, Eliza L.; Lindsey, Bruce D.; Rupert, Michael G.

2012-01-01

Field blank samples help determine the frequency and magnitude of contamination bias, and replicate samples help determine the sampling variability (error) of measured analyte concentrations. Quality control data were evaluated for calcium, magnesium, sodium, potassium, chloride, sulfate, fluoride, silica, and total dissolved solids. A 99-percent upper confidence limit is calculated from field blanks to assess the potential for contamination bias. For magnesium, potassium, chloride, sulfate, and fluoride, potential contamination in more than 95 percent of environmental samples is less than or equal to the common maximum reporting level. Contamination bias has little effect on measured concentrations greater than 4.74 mg/L (milligrams per liter) for calcium, 14.98 mg/L for silica, 4.9 mg/L for sodium, and 120 mg/L for total dissolved solids. Estimates of sampling variability are calculated for high and low ranges of concentration for major ions and total dissolved solids. Examples showing the calculation of confidence intervals and how to determine whether measured differences between two water samples are significant are presented.

The role of volatiles in the genesis of cenozoic magmatism in Northern Victoria Land (NVL), Antarctica

NASA Astrophysics Data System (ADS)

Giacomoni, Pier Paolo; Coltorti, Massimo; Bonadiman, Costanza; Ferlito, Carmelo; Zanetti, Alberto; Ottolini, Luisa

2017-04-01

This study offers an innovative view of the petrogenetic processes responsible for the magmas erupted in the Western Antarctic Rift System (WARS) by studying the chemical composition and the volatiles content of basic lavas and olivine-hosted melt inclusions (MI). Lavas come from three localities: Shield Nunatak (Mt. Melbourne), Eldridge Bluff and Handler Ridge. They are olivine-phyric basanites (42.41-44.80 SiO2 wt%; 3.11-6.19 Na2O+K2O wt%) and basalts (44.91-48.73 SiO2 wt%; 2.81-4.55 Na2O+K2O wt%) with minor clinopyroxene and plagioclase. Samples from Handler Ridge clearly differ by having the highest TiO2 (3.55-3.65 wt%), Rb, Ba, Nb, La, Zr despite their more primitive features (60.83-44.87 Mg#, MgO/(MgO+FeO) %mol). Olivine-hosted melt inclusions (MI) were analyzed for major element and volatiles (H2O. CO2, S, F, and Cl) after HT (1300°C) and HP (6 kbar) homogenization. Despite a larger variability, MI are compositionally comparable with the host lavas and are characterized by two distinct trends (high-Fe-Ti-K and low-Fe-Ti-K). The H2O content in MI ranges from 0.70 wt% to 2.64 wt% and CO2 from 25 ppm to 341 ppm (H2O/CO2 1). At comparable H2O contents, few samples show a higher CO2 values (1322 ppm to 3905 ppm) with a H2O/CO2 molar ratio down to 0.8. F and Cl content varies from 1386 ppm to 10 ppm and from 1336 ppm to 38 ppm respectively. Concentration of volatiles show a good correlation with alkalies, especially with K2O; Handler Ridge presents the highest total value of F and Cl (2675 ppm). Chondrite-normalized trace elements concentration in MI show an intraplate pattern with negative anomalies in Rb, K, Ti. Accordingly, to the lava contents, MI from Handler Ridge have a significantly higher concentration in Rb (12-45 ppm), Sr (700-834 ppm), Ba (433-554) and Nb (48.8-83.4 ppm) with respect to the other localities at comparable Mg#. Mantle melting mass balance calculations simulate the observed H2O, CO2 and Cl concentration by melting a spinel lhezolite from 3 to 7 % of melting (F) with a 5% of modal amphibole with the same composition and modal proportion of mantle xenoliths from Baker Rocks, a locality near to Shield Nunatak. The model was not able to predict the F content which is less abundant in natural sample. From the resulted partial melting percentage, we calculated a total amount of CO2 in mantle source of 273 ppm by assuming the highest 3900 ppm measured in MI as starting value. The estimated maximum content of H2O and CO2 in the primary melt is 2.6 wt% and 8800 ppm respectively. Obtained data were compared with those from mantle xenoliths from NVL with the aim to reconstruct the composition of the mantle source of the Cenozoic magmatism and to model the whole volatile budget from mantle to magmas starting from the measured volatile content in hydrous (amph) and NAM phases in mantle xenoliths. Preliminary results evidence that high-Fe-Ti-K basanites found in MI are very similar to the calculated metasomatic agent involved in the formation of the very peculiar Fe-rich lherzolites.

Lake Roosevelt Fisheries Evaluation Program; Limnological and Fisheries Monitoring, Annual Report 2000.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Chuck; Scofield, Ben; Pavlik, Deanne

2003-03-01

A slightly dryer than normal year yielded flows in Lake Roosevelt that were essentially equal to the past ten year average. Annual mean inflow and outflow were 3,160.3 m3/s and 3,063.4 m3/s respectively. Mean reservoir elevation was 387.2 m above sea level at the Grand Coulee Dam forebay. The forebay elevation was below the mean elevation for a total of 168 days. During the first half of the 2000 forebay elevation changed at a rate of 0.121 m/d and during the last half changed at a rate of 0.208 m/d. The higher rate of elevation change earlier in the yearmore » is due to the drawdown to accommodate spring runoff. Mean annual water retention time was 40 days. Annual mean total dissolved gas was 108%. Total dissolved gas was greatest at upriver locations (110% = US/Canada Border annual mean) and decreased moving toward Grand Coulee Dam (106% = Grand Coulee Dam Forebay annual mean). Total dissolved gas was greatest in May (122% reservoir wide monthly mean). Gas bubble trauma was observed in 16 fish primarily largescale suckers and was low in severity. Reservoir wide mean temperatures were greatest in August (19.5 C) and lowest in January (5.5 C). The Spokane River and Sanpoil River Arms experienced higher temperatures than the mainstem reservoir. Brief stratification was observed at the Sanpoil River shore location in July. Warm water temperatures in the Spokane Arm contributed to low dissolved oxygen concentrations in August (2.6 mg/L at 33 m). However, decomposition of summer algal biomass was likely the main cause of depressed dissolved oxygen concentrations. Otherwise, dissolved oxygen profiles were relatively uniform throughout the water column across other sampling locations. Annual mean Secchi depth throughout the reservoir was 5.7 m. Nutrient concentrations were generally low, however, annual mean total phosphorus (0.016 mg/L) was in the mesotrophic range. Annual mean total nitrogen was in the meso-oligotrophic range. Total nitrogen to total phosphorus ratios were large (31:1 annual mean) likely indicating phosphorus limitations to phytoplankton.« less

DISTRIBUTION AND COMPOSITION OF DISSOLVED AND PARTICULATE ORGANIC CARBON IN NORTHERN SAN FRANCISCO BAY DURING LOW FRESHWATER FLOW CONDITIONS

EPA Science Inventory

The distribution of organic matter was studied in northern San Francisco Bay monthly through spring and summer 1996 along the salinity gradient from the Sacramento River to Central Bay. Dissolved constituents included monosaccharides (MONO), total carbohydrates (TCHO), dissolved ...

Magma transport and olivine crystallization depths in Kīlauea’s East Rift Zone inferred from experimentally rehomogenized melt inclusions

USGS Publications Warehouse

Tuohy, Robin M; Wallace, Paul J.; Loewen, Matthew W; Swanson, Don; Kent, Adam J R

2016-01-01

Concentrations of H2O and CO2 in olivine-hosted melt inclusions can be used to estimate crystallization depths for the olivine host. However, the original dissolved CO2concentration of melt inclusions at the time of trapping can be difficult to measure directly because in many cases substantial CO2 is transferred to shrinkage bubbles that form during post-entrapment cooling and crystallization. To investigate this problem, we heated olivine from the 1959 Kīlauea Iki and 1960 Kapoho (Hawai‘i) eruptions in a 1-atm furnace to temperatures above the melt inclusion trapping temperature to redissolve the CO2 in shrinkage bubbles. The measured CO2 concentrations of the experimentally rehomogenized inclusions (⩽590 ppm for Kīlauea Iki [n=10]; ⩽880 ppm for Kapoho, with one inclusion at 1863 ppm [n=38]) overlap with values for naturally quenched inclusions from the same samples, but experimentally rehomogenized inclusions have higher within-sample median CO2 values than naturally quenched inclusions, indicating at least partial dissolution of CO2 from the vapor bubble during heating. Comparison of our data with predictions from modeling of vapor bubble formation and published Raman data on the density of CO2 in the vapor bubbles suggests that 55-85% of the dissolved CO2 in the melt inclusions at the time of trapping was lost to post-entrapment shrinkage bubbles. Our results combined with the Raman data demonstrate that olivine from the early part of the Kīlauea Iki eruption crystallized at <6 km depth, with the majority of olivine in the 1-3 km depth range. These depths are consistent with the interpretation that the Kīlauea Iki magma was supplied from Kīlauea’s summit magma reservoir (∼2-5 km depth). In contrast, olivine from Kapoho, which was the rift zone extension of the Kīlauea Iki eruption, crystallized over a much wider range of depths (∼1-16 km). The wider depth range requires magma transport during the Kapoho eruption from deep beneath the summit region and/or from deep beneath Kīlauea’s east rift zone. The deeply derived olivine crystals and their host magma mixed with stored, more evolved magma in the rift zone, and the mixture was later erupted at Kapoho.

Magma transport and olivine crystallization depths in Kīlauea's east rift zone inferred from experimentally rehomogenized melt inclusions

NASA Astrophysics Data System (ADS)

Tuohy, Robin M.; Wallace, Paul J.; Loewen, Matthew W.; Swanson, Donald A.; Kent, Adam J. R.

2016-07-01

Concentrations of H2O and CO2 in olivine-hosted melt inclusions can be used to estimate crystallization depths for the olivine host. However, the original dissolved CO2 concentration of melt inclusions at the time of trapping can be difficult to measure directly because in many cases substantial CO2 is transferred to shrinkage bubbles that form during post-entrapment cooling and crystallization. To investigate this problem, we heated olivine from the 1959 Kīlauea Iki and 1960 Kapoho (Hawai'i) eruptions in a 1-atm furnace to temperatures above the melt inclusion trapping temperature to redissolve the CO2 in shrinkage bubbles. The measured CO2 concentrations of the experimentally rehomogenized inclusions (⩽590 ppm for Kīlauea Iki [n = 10]; ⩽880 ppm for Kapoho, with one inclusion at 1863 ppm [n = 38]) overlap with values for naturally quenched inclusions from the same samples, but experimentally rehomogenized inclusions have higher within-sample median CO2 values than naturally quenched inclusions, indicating at least partial dissolution of CO2 from the vapor bubble during heating. Comparison of our data with predictions from modeling of vapor bubble formation and published Raman data on the density of CO2 in the vapor bubbles suggests that 55-85% of the dissolved CO2 in the melt inclusions at the time of trapping was lost to post-entrapment shrinkage bubbles. Our results combined with the Raman data demonstrate that olivine from the early part of the Kīlauea Iki eruption crystallized at <6 km depth, with the majority of olivine in the 1-3 km depth range. These depths are consistent with the interpretation that the Kīlauea Iki magma was supplied from Kīlauea's summit magma reservoir (∼2-5 km depth). In contrast, olivine from Kapoho, which was the rift zone extension of the Kīlauea Iki eruption, crystallized over a much wider range of depths (∼1-16 km). The wider depth range requires magma transport during the Kapoho eruption from deep beneath the summit region and/or from deep beneath Kīlauea's east rift zone. The deeply derived olivine crystals and their host magma mixed with stored, more evolved magma in the rift zone, and the mixture was later erupted at Kapoho.

Environmental control on concretion-forming processes: Examples from Paleozoic terrigenous sediments of the North Gondwana margin, Armorican Massif (Middle Ordovician and Middle Devonian) and SW Sardinia (Late Ordovician)

NASA Astrophysics Data System (ADS)

Dabard, Marie-Pierre; Loi, Alfredo

2012-08-01

Concretions of various compositions are common in the Paleozoic terrigenous successions of the north Gondwana margin. This study focuses on phosphatic (P) and siliceous (Si) concretions present in some successions of the Armorican Massif (NW France) and SW Sardinia (W Italy). It shows that they consist of mudstones, fine- to very fine-grained sandstones or shellbeds with a more or less abundant P-cement and form a continuum between a phosphatic end-member and a siliceous biogenic end-member. The P2O5 contents are ranging from 0.26% to 21.5% and are related to apatite. The SiO2 contents vary from 25% to 82% and are linked both to a terrigenous phase and to a biogenic silica phase. Concretions showing the lower P-contents (P2O5 < 1.5%) are often enriched in biogenic silica (SiO2/Al2O3 > 5). Comparison with the surrounding sediments shows that all the concretions are enriched in chlorite and in Middle Rare Earth Elements (Las/Gds: 0.12-0.72) and some of them in Y (up to 974 ppm), Rare Earth Elements (more than 300 ppm) and Sr (260-880 ppm). The concretions with highest biogenic silica concentrations are contained in the outer shelf sediments whereas the other concretions are present from the proximal part of the inner shelf to the outer shelf. A genetic model in two stages is proposed. During early diagenesis, the dissolution of shells and degradation of organic matter progressively enrich the pore water in dissolved Si, Ca and P. When the suboxic zone is reached, P-precipitation begins, leading to the formation of protoconcretions. In shallow environments, the relative permeability of sediments and the winnowing or reworking of the upper few centimetres by bottom currents allow for suboxic conditions to be maintained, leading to P-rich concretion formation. In deeper environments, the anoxic zone is reached more rapidly, thereby preventing extensive phosphogenesis. Nevertheless in the protoconcretions the early P-cement preserves pore spaces from compaction. In the presence of biogenic siliceous particles, the fluids are enriched in dissolved silica and diffuse towards the protoconcretions. Silica precipitation can thus occur later in the intergranular spaces.

Nitrate Attenuation Pathways and Capacity in Urban Wetlands of Phoenix, Arizona.

NASA Astrophysics Data System (ADS)

Handler, A. M.; Suchy, A. K.; Grimm, N. B.; Palta, M.; Childers, D. L.; Stromberg, J. C.

2016-12-01

In the urban Salt River channel of Phoenix, Arizona, stormwater pipes collect urban runoff that drains directly into the dry river bed, providing a new water source that sustains perennial wetlands. Water delivered by storm drains is enriched in nitrogen, particularly nitrate (NO3-), a common surface-water pollutant. However, these systems are not planned nor are they actively managed to reduce nitrogen loads. We investigated the microbial capacity of these wetlands to reduce nitrate concentrations by examining surface-water (SW) and subsurface porewater (PW) chemistry and conducting soil incubations from dominant wetland vegetation patches. Nitrate was higher in SW than PW (mean ± S.E.: 0.23 ± 0.05 vs. 0.03 ± 0.01 ppm N-NO3-) while ammonium (NH4+) was the opposite (0.11 ± 0.02 vs. 0.47 ± 0.10 ppm N-NH4+). Dissolved organic carbon (DOC) was abundant throughout the wetland (6.0 ± 0.9 ppm), but was significantly higher in vegetated patches compared to non-vegetated patches (t-test: p=0.04). These data indicate conditions that support microbial NO3- reduction persists, especially in vegetated patches. Laboratory incubations of wetland soil treated with a high (7 ppm) and low (1 ppm) dose of NO3- consumed 0.191 ± 0.022 and 0.019 ± 0.005 mg N-NO3- hr-1 kg wet soil-1, respectively. A best-fit model showed incubations with a higher starting NO3- concentration had a higher NO3- loss rate (standardized β=0.10 ± 0.01, p<0.001) and incubations from vegetated patches had a higher NO3- loss rate than those from open patches (β=0.02 ± 0.01, p=0.003). Across patches, NH4+ increased in the high treatment incubations (t-test: p<0.001), potentially indicating the presence of dissimilatory nitrate reduction to ammonium (DNRA). These results suggest the wetlands have the capacity to both remove nitrogen via denitrification and retain it via DNRA. This study indicates unplanned, unmanaged urban wetland systems have a high capacity to attenuate NO3- delivered from the urban landscape.

Carbon Cycling of Lake Kivu (East Africa): Net Autotrophy in the Epilimnion and Emission of CO2 to the Atmosphere Sustained by Geogenic Inputs

PubMed Central

Borges, Alberto V.; Morana, Cédric; Bouillon, Steven; Servais, Pierre; Descy, Jean-Pierre; Darchambeau, François

2014-01-01

We report organic and inorganic carbon distributions and fluxes in a large (>2000 km2) oligotrophic, tropical lake (Lake Kivu, East Africa), acquired during four field surveys, that captured the seasonal variations (March 2007–mid rainy season, September 2007–late dry season, June 2008–early dry season, and April 2009–late rainy season). The partial pressure of CO2 (pCO2) in surface waters of the main basin of Lake Kivu showed modest spatial (coefficient of variation between 3% and 6%), and seasonal variations with an amplitude of 163 ppm (between 579±23 ppm on average in March 2007 and 742±28 ppm on average in September 2007). The most prominent spatial feature of the pCO2 distribution was the very high pCO2 values in Kabuno Bay (a small sub-basin with little connection to the main lake) ranging between 11213 ppm and 14213 ppm (between 18 and 26 times higher than in the main basin). Surface waters of the main basin of Lake Kivu were a net source of CO2 to the atmosphere at an average rate of 10.8 mmol m−2 d−1, which is lower than the global average reported for freshwater, saline, and volcanic lakes. In Kabuno Bay, the CO2 emission to the atmosphere was on average 500.7 mmol m−2 d−1 (∼46 times higher than in the main basin). Based on whole-lake mass balance of dissolved inorganic carbon (DIC) bulk concentrations and of its stable carbon isotope composition, we show that the epilimnion of Lake Kivu was net autotrophic. This is due to the modest river inputs of organic carbon owing to the small ratio of catchment area to lake surface area (2.15). The carbon budget implies that the CO2 emission to the atmosphere must be sustained by DIC inputs of geogenic origin from deep geothermal springs. PMID:25314144

Global Fund financing of public-private mix approaches for delivery of tuberculosis care.

PubMed

Lal, S S; Uplekar, Mukund; Katz, Itamar; Lonnroth, Knut; Komatsu, Ryuichi; Yesudian Dias, Hannah Monica; Atun, Rifat

2011-06-01

To map the extent and scope of public-private mix (PPM) interventions in tuberculosis (TB) control programmes supported by the Global Fund. We reviewed the Global Fund's official documents and data to analyse the distribution, characteristics and budgets of PPM approaches within Global Fund supported TB grants in recipient countries between 2003 and 2008. We supplemented this analysis with data on contribution of PPM to TB case notifications in 14 countries reported to World Health Organization in 2009, for the preparation of the global TB control report. Fifty-eight of 93 countries and multi-country recipients of Global Fund-supported TB grants had PPM activities in 2008. Engagement with 'for-profit' private sector was more prevalent in South Asia while involvement of prison health services has been common in Eastern Europe and central Asia. In the Middle East and North Africa, involving non-governmental organizations seemed to be the focus. Average and median spending on PPM within grants was 10% and 5% respectively, ranging from 0.03% to 69% of the total grant budget. In China, India, Nigeria and the Philippines, PPM contributed to detecting more than 25% TB cases while maintaining high treatment success rates. In spite of evidence of cost-effectiveness, PPM constitutes only a modest part of overall TB control activities. Scaling up PPM across countries could contribute to expanding access to TB care, increasing case detection, improving treatment outcomes and help achieve the global TB control targets. © 2011 Blackwell Publishing Ltd.

Dietary human exposure to mercury in two artisanal small-scale gold mining communities of northwestern Colombia.

PubMed

Salazar-Camacho, Carlos; Salas-Moreno, Manuel; Marrugo-Madrid, Siday; Marrugo-Negrete, José; Díez, Sergi

2017-10-01

Artisanal and small-scale gold mining (ASGM) is the largest anthropogenic source of mercury pollution worldwide, posing a grave threat to human health. The present study identifies current levels of mercury in the human population from mining areas of the Chocó Department, Colombia, through total mercury (THg) and methylmercury (MeHg) measurements in human hair. Mercury exposure of the local population was assessed in two towns affected by ASGM and was related to different variables of interest. Concentrations of THg in human hair ranged from 0.06 to 17.54ppm and the mean value for the subjects under study was 2.48ppm. Men had significantly higher levels than women in both towns (3.29ppm vs. 0.77ppm). Fish consumption was related to a marked increase of THg in hair, with mean values close to five times higher in frequent fish consumers (5-7 times/week) than in non-fish consumers (4.80ppm vs. 0.90ppm). A multiple linear regression model was fitted successfully (R=0.671) and reveals that gender, fish consumption and location of residence were significant indicators of Hg levels in hair, while no significant relationship was found for age. Approximately 60% of subjects tested had THg levels that exceeded the U.S. Environmental Protection Agency reference dose of 1.0ppm, while 25% surpassed that of the World Health Organization (2.2ppm). Copyright © 2017 Elsevier Ltd. All rights reserved.

Water-Chemistry Data for Selected Springs, Geysers, and Streams in Yellowstone National Park, Wyoming, 2003-2005

USGS Publications Warehouse

Ball, James W.; McCleskey, R. Blaine; Nordstrom, D. Kirk; Holloway, JoAnn M.

2008-01-01

Water analyses are reported for 157 samples collected from numerous hot springs, their overflow drainages, and Lemonade Creek in Yellowstone National Park (YNP) during 2003-2005. Water samples were collected and analyzed for major and trace constituents from ten areas of YNP including Terrace and Beryl Springs in the Gibbon Canyon area, Norris Geyser Basin, the West Nymph Creek thermal area, the area near Nymph Lake, Hazle Lake, and Frying Pan Spring, Lower Geyser Basin, Washburn Hot Springs, Mammoth Hot Springs, Potts Hot Spring Basin, the Sulphur Caldron area, and Lemonade Creek near the Solfatara Trail. These water samples were collected and analyzed as part of research investigations in YNP on arsenic, antimony, and sulfur redox distribution in hot springs and overflow drainages, and the occurrence and distribution of dissolved mercury. Most samples were analyzed for major cations and anions, trace metals, redox species of antimony, arsenic, iron, nitrogen, and sulfur, and isotopes of hydrogen and oxygen. Analyses were performed at the sampling site, in an on-site mobile laboratory vehicle, or later in a U.S. Geological Survey laboratory, depending on stability of the constituent and whether it could be preserved effectively. Water samples were filtered and preserved onsite. Water temperature, specific conductance, pH, Eh (redox potential relative to the Standard Hydrogen Electrode), and dissolved hydrogen sulfide were measured onsite at the time of sampling. Acidity was determined by titration, usually within a few days of sample collection. Alkalinity was determined by titration within 1 to 2 weeks of sample collection. Concentrations of thiosulfate and polythionate were determined as soon as possible (generally minutes to hours after sample collection) by ion chromatography in an on-site mobile laboratory vehicle. Total dissolved-iron and ferrous-iron concentrations often were measured onsite in the mobile laboratory vehicle. Concentrations of dissolved aluminum, arsenic, boron, barium, beryllium, calcium, cadmium, cobalt, chromium, copper, iron, potassium, lithium, magnesium, manganese, molybdenum, sodium, nickel, lead, selenium, silica, strontium, vanadium, and zinc were determined by inductively-coupled plasma-optical emission spectrometry. Trace concentrations of dissolved antimony, cadmium, cobalt, chromium, copper, lead, and selenium were determined by Zeeman-corrected graphite-furnace atomic-absorption spectrometry. Dissolved concentrations of total arsenic, arsenite, total antimony, and antimonite were determined by hydride-generation atomic-absorption spectrometry using a flow-injection analysis system. Dissolved concentrations of total mercury and methyl mercury were determined by cold-vapor atomic-fluorescence spectrometry. Concentrations of dissolved chloride, fluoride, nitrate, bromide, and sulfate were determined by ion chromatography. Concentrations of dissolved ferrous and total iron were determined by the FerroZine colorimetric method. Concentrations of dissolved nitrite were determined by colorimetry or chemiluminescence. Concentrations of dissolved ammonium were determined by ion chromatography, with reanalysis by colorimetry when separation of sodium and ammonia peaks was poor. Dissolved organic carbon concentrations were determined by the wet persulfate oxidation method. Hydrogen and oxygen isotope ratios were determined using the hydrogen and CO2 equilibration techniques, respectively.

Variations in statewide water quality of New Jersey streams, water years 1998-2009

USGS Publications Warehouse

Heckathorn, Heather A.; Deetz, Anna C.

2012-01-01

Statistical analyses were conducted for six water-quality constituents measured at 371 surface-water-quality stations during water years 1998-2009 to determine changes in concentrations over time. This study examined year-round concentrations of total dissolved solids, dissolved nitrite plus nitrate, dissolved phosphorus, total phosphorus, and total nitrogen; concentrations of dissolved chloride were measured only from January to March. All the water-quality data analyzed were collected by the New Jersey Department of Environmental Protection and the U.S. Geological Survey as part of the cooperative Ambient Surface-Water-Quality Monitoring Network. Stations were divided into groups according to the 1-year or 2-year period that the stations were part of the Ambient Surface-Water-Quality Monitoring Network. Data were obtained from the eight groups of Statewide Status stations for water years 1998, 1999, 2000, 2001-02, 2003-04, 2005-06, 2007-08, and 2009. The data from each group were compared to the data from each of the other groups and to baseline data obtained from Background stations unaffected by human activity that were sampled during the same time periods. The Kruskal-Wallis test was used to determine whether median concentrations of a selected water-quality constituent measured in a particular 1-year or 2-year group were different from those measured in other 1-year or 2-year groups. If the median concentrations were found to differ among years or groups of years, then Tukey's multiple comparison test on ranks was used to identify those years with different or equal concentrations of water-quality constituents. A significance level of 0.05 was selected to indicate significant changes in median concentrations of water-quality constituents. More variations in the median concentrations of water-quality constituents were observed at Statewide Status stations (randomly chosen stations scattered throughout the State of New Jersey) than at Background stations (control stations that are located on reaches of streams relatively unaffected by human activity) during water years 1998-2009. Results of tests on concentrations of total dissolved solids, dissolved chloride, dissolved nitrite plus nitrate, total phosphorus, and total nitrogen indicate a significant difference in water quality at Statewide Status stations but not at Background stations during the study period. Excluding water year 2009, all significant changes that were observed in the median concentrations were ultimately increases, except for total phosphorus, which varied significantly but in an inconsistent pattern during water years 1998-2009. Streamflow data aided in the interpretation of the results for this study. Extreme values of water-quality constituents generally followed inverse patterns of streamflow. Low streamflow conditions helped explain elevated concentrations of several constituents during water years 2001-02. During extreme drought conditions in 2002, maximum concentrations occurred for four of the six water-quality constituents examined in this study at Statewide Status stations (maximum concentration of 4,190 milligrams per liter of total dissolved solids) and three of six constituents at Background stations (maximum concentration of 179 milligrams per liter of total dissolved solids). The changes in water quality observed in this study parallel many of the findings from previous studies of trends in New Jersey.

Partitioning of uranyl between ferrihydrite and humic substances at acidic and circum-neutral pH

NASA Astrophysics Data System (ADS)

Dublet, Gabrielle; Lezama Pacheco, Juan; Bargar, John R.; Fendorf, Scott; Kumar, Naresh; Lowry, Gregory V.; Brown, Gordon E.

2017-10-01

As part of a larger study of the reactivity and mobility of uranyl (U(VI)O22+) cations in subsurface environments containing natural organic matter (NOM) and hydrous ferric oxides, we have examined the effect of reference humic and fulvic substances on the sorption of uranyl on 2-line ferrihydrite (Fh), a common, naturally occurring nano-Fe(III)-hydroxide. Uranyl was reacted with Fh at pH 4.6 and 7.0 in the presence and absence of Elliott Soil Humic Acid (ESHA) (0-835 ppm) or Suwanee River Fulvic Acid (SRFA) (0-955 ppm). No evidence was found for reduction of uranyl by either form of NOM after 24 h of exposure. The following three size fractions were considered in this study: (1) ≥0.2 μm (Fh-NOM aggregates), (2) 0.02-0.2 μm (dispersed Fh nanoparticles and NOM macro-molecules), and (3) <0.02 μm (dissolved). The extent to which U(VI) is sorbed in aggregates or dispersed as colloids was assessed by comparing U, Fe, and NOM concentrations in these three size fractions. Partitioning of uranyl between Fh and NOM was determined in size fraction (1) using X-ray absorption spectroscopy (XAS). Uranyl sorption on Fh-NOM aggregates was affected by the presence of NOM in different ways depending on pH and type of NOM (ESHA vs. SRFA). The presence of ESHA in the uranyl-Fh-NOM ternary system at pH 4.6 enhanced uranyl uptake more than the presence of SRFA. In contrast, neither form of NOM affected uranyl sorption at pH 7.0 over most of the NOM concentration range examined (0-500 ppm); at the highest NOM concentrations (500-955 ppm) uranyl uptake in the aggregates was slightly inhibited at pH 7.0, which is interpreted as being due to the dispersion of Fh aggregates. XAS at the U LIII-edge was used to characterize molecular-level changes in uranyl complexation as a result of sorption to the Fh-NOM aggregates. In the absence of NOM, uranyl formed dominantly inner-sphere, mononuclear, bidentate sorption complexes on Fh. However, when NOM concentration was increased at pH 4.6, the proportion of uranyl-Fh inner-sphere sorption complexes decreased relative to uranyl-ESHA or uranyl-SRFA complexes, which comprised up to ∼60% of the total uranyl in the systems studied. At pH 7.0, uranyl-NOM complexes were also present in the Fh-NOM aggregates in the concentration ranges of ESHA or SRFA considered; however, the proportion of these complexes was smaller at pH 7.0 than at pH 4.6 and did not increase significantly with increasing NOM concentration.

Onsite biological treatment of an industrial landfill leachate: Microbiological and engineering considerations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skladany, G.J.

Successful biological treatment of ground waters, leachates, or industrial process waters requires the combined action of basic microbiological processes with sound process engineering designs. Such a treatment system is then able to both efficiently and cost-effectively remediate the contaminants present. In this case study, laboratory treatability studies were initially used to demonstrate that toluic acids present in an industrial landfill leachate were amenable to biological treatment. A continuous flow submerged fixed-film bioreactor was then chosen as the optimal equipment design for use at the site. The system was designed to treat a leachate flow of 800 to 2,000 gallons permore » day (gpd) containing total isomeric toluic acid concentrations of 300 to 400 parts per million (ppm). The treatment equipment has been in continuous operation since July 1987. During this period, the total influent isomertic toluic acid concentration has decreased to approximately 45 ppm, and specific effluent toluic acid concentrations have remained below the 0.5 ppm detection limit.« less

Laboratory measurements of radiance and reflectance spectra of a dilute biosolid industrial waste product

NASA Technical Reports Server (NTRS)

Usry, J. W.; Witte, W. G.; Whitlock, C. H.; Gurganus, E. A.

1979-01-01

Experimental measurements were made of upwelled spectral signatures of various concentrations of industrial waste products mixed with water in a large water tank. Radiance and reflectance spectra for a biosolid waste product (sludge) mixed with conditioned tap water and natural river water are reported. Results of these experiments indicate that reflectance increases with increasing concentration of the sludge at practically all wavelengths for concentration of total suspended solids up to 117 ppm in conditioned tap water and 171 ppm in natural river water. Significant variations in the spectra were observed and may be useful in defining spectral characteristics for this waste product. No significant spectral differences were apparent in the reflectance spectra of the two experiments, especially for wavelengths greater than 540 nm. Reflectance values, however, were generally greater in natural river water for wavelengths greater than 540 nm. Reflectance may be considered to increase linearly with concentration of total suspended solids from 5 to 171 ppm at all wavelengths without introducing errors larger than 10 percent.

Water-chemistry data for selected springs, geysers, and streams in Yellowstone National Park, Wyoming, 2006-2008

USGS Publications Warehouse

Ball, James W.; McMleskey, R. Blaine; Nordstrom, D. Kirk

2010-01-01

Water analyses are reported for 104 samples collected from numerous thermal and non-thermal features in Yellowstone National Park (YNP) during 2006-2008. Water samples were collected and analyzed for major and trace constituents from 10 areas of YNP including Apollinaris Spring and Nymphy Creek along the Norris-Mammoth corridor, Beryl Spring in Gibbon Canyon, Norris Geyser Basin, Lower Geyser Basin, Crater Hills, the Geyser Springs Group, Nez Perce Creek, Rabbit Creek, the Mud Volcano area, and Washburn Hot Springs. These water samples were collected and analyzed as part of research investigations in YNP on arsenic, antimony, iron, nitrogen, and sulfur redox species in hot springs and overflow drainages, and the occurrence and distribution of dissolved mercury. Most samples were analyzed for major cations and anions, trace metals, redox species of antimony, arsenic, iron, nitrogen, and sulfur, and isotopes of hydrogen and oxygen. Analyses were performed at the sampling site, in an on-site mobile laboratory vehicle, or later in a U.S. Geological Survey laboratory, depending on stability of the constituent and whether it could be preserved effectively. Water samples were filtered and preserved on-site. Water temperature, specific conductance, pH, emf (electromotive force or electrical potential), and dissolved hydrogen sulfide were measured on-site at the time of sampling. Dissolved hydrogen sulfide was measured a few to several hours after sample collection by ion-specific electrode on samples preserved on-site. Acidity was determined by titration, usually within a few days of sample collection. Alkalinity was determined by titration within 1 to 2 weeks of sample collection. Concentrations of thiosulfate and polythionate were determined as soon as possible (generally a few to several hours after sample collection) by ion chromatography in an on-site mobile laboratory vehicle. Total dissolved iron and ferrous iron concentrations often were measured on-site in the mobile laboratory vehicle. Concentrations of dissolved aluminum, arsenic, boron, barium, beryllium, calcium, cadmium, cobalt, chromium, copper, iron, potassium, lithium, magnesium, manganese, molybdenum, sodium, nickel, lead, selenium, silica, strontium, vanadium, and zinc were determined by inductively coupled plasma-optical emission spectrometry. Trace concentrations of dissolved antimony, cadmium, cobalt, chromium, copper, lead, and selenium were determined by Zeeman-corrected graphite-furnace atomic-absorption spectrometry. Dissolved concentrations of total arsenic, arsenite, total antimony, and antimonite were determined by hydride generation atomic-absorption spectrometry using a flow-injection analysis system. Dissolved concentrations of total mercury and methylmercury were determined by cold-vapor atomic fluorescence spectrometry. Concentrations of dissolved chloride, fluoride, nitrate, bromide, and sulfate were determined by ion chromatography. For many samples, concentrations of dissolved fluoride also were determined by ion-specific electrode. Concentrations of dissolved ferrous and total iron were determined by the FerroZine colorimetric method. Concentrations of dissolved ammonium were determined by ion chromatography, with reanalysis by colorimetry when separation of sodium and ammonia peaks was poor. Dissolved organic carbon concentrations were determined by the wet persulfate oxidation method. Hydrogen and oxygen isotope ratios were determined using the hydrogen and CO2 equilibration techniques, respectively.

Application of banana peels waste as adsorbents for the removal of CO2, NO, NOx, and SO2 gases from motorcycle emissions

NASA Astrophysics Data System (ADS)

Viena, V.; Elvitriana; Wardani, S.

2018-03-01

The aims of the study were to investigate the application of banana peels as adsorbent for the removal of CO, NO, NOx and SO2 gases from motorcycles emissions. The effect of differents thermal activation on the characteristics of banana peels adsorbent (BPA) such as moisture content, ash content, volatile matter and fixed carbon has been studied using proximate analysis. The study of Iodine adsorption capacity of BPA was obtained at 952 mg/g adsorbent. Structure and morphology of BPA were characterized by Fourier transform infrared (FTIR) and field emission scanning electron microscopy (SEM). The results showed that BPA could significantly adsorbed the CO and SO2 gases emissions from motorcycles, but not applicable for NO, NOx gases. After 10 minutes of flue gas analysis at idle mode using BPA adsorption tube, CO gas could be totally removed, from initial 19618 ppm to 0 ppm, while SO2 gas could also be totally removed from 24523 ppm to 0 ppm. SEM test showed that temperature of activation had significant effect on the size of pores of BPA formed. BPA was suitable for application in removing CO and SO2 gases emissions from motorcycles and it helps to reduce the green house gas effects of fossil fuel to the environment.

Sensitive monitoring of iodine species in sea water using capillary electrophoresis: vertical profiles of dissolved iodine in the Pacific Ocean.

PubMed

Huang, Zhuo; Ito, Kazuaki; Morita, Isamu; Yokota, Kuriko; Fukushi, Keiichi; Timerbaev, Andrei R; Watanabe, Shuichi; Hirokawa, Takeshi

2005-08-01

Using a novel high-sensitivity capillary electrophoretic method, vertical distributions of iodate, iodide, total inorganic iodine, dissolved organic iodine and total iodine in the North Pacific Ocean (0-5500 m) were determined without any sample pre-treatment other than UV irradiation before total iodine analysis. An extensive set of data demonstrated that the iodine behaviour in the ocean water collected during a cruise in the North Pacific Ocean in February-March 2003 was not conservative but correlated with variations in concentrations of dissolved oxygen and nutrient elements such as silicon, nitrogen and phosphorus. This suggests that the vertical distribution of iodine is associated with biological activities. The dissolved organic iodine was found in the euphotic zone in accord with observations elsewhere in the oceans. The vertical profile of dissolved organic iodine also appears to be related to biogeochemical activity. The concentrations of all measured iodine species vary noticeably above 1000 m but only minor latitudinal changes occur below 1000 m and slight vertical alterations can be observed below 2400 m. These findings are thought to reflect the stratification of nutrients and iodine species with different biological activities in the water column.

Mercury, monomethyl mercury, and dissolved organic carbon concentrations in surface water entering and exiting constructed wetlands treated with metal-based coagulants, Twitchell Island, California

USGS Publications Warehouse

Stumpner, Elizabeth B.; Kraus, Tamara E.C.; Fleck, Jacob A.; Hansen, Angela M.; Bachand, Sandra M.; Horwath, William R.; DeWild, John F.; Krabbenhoft, David P.; Bachand, Philip A.M.

2015-09-02

Following coagulation, but prior to passage through the wetland cells, coagulation treatments transferred dissolved mercury and carbon to the particulate fraction relative to untreated source water: at the wetland cell inlets, the coagulation treatments decreased concentrations of filtered total mercury by 59–76 percent, filtered monomethyl mercury by 40–70 percent, and dissolved organic carbon by 65–86 percent. Passage through the wetland cells decreased the particulate fraction of mercury in wetland cells that received coagulant-treated water. Changes in total mercury, monomethyl mercury, and dissolved organic carbon concentrations resulting from wetland passage varied both by treatment and season. Despite increased monomethyl mercury in the filtered fraction during wetland passage between March and August, the coagulation-wetland systems generally decreased total mercury (filtered plus particulate) and monomethyl mercury (filtered plus particulate) concentrations relative to source water. Coagulation—either alone or in association with constructed wetlands—could be an effective way to decrease concentrations of mercury and dissolved organic carbon in surface water as well as the bioavailability of mercury in the Sacramento–San Joaquin Delta.

Methylmercury level in umbilical cords from patients with congenital Minamata disease.

PubMed

Harada, M; Akagi, H; Tsuda, T; Kizaki, T; Ohno, H

1999-08-30

A total of 151 umbilical cords during the period from 1950 to 1969 were collected from the residents of the Minamata area (including 25 patients with congenital Minamata disease) for methylmercury (MeHg) analysis. When the MeHg discharge from the Chisso Company's Minamata factory into the Minamata Bay is compared with the incidence of congenital Minamata disease, the abrupt increase of the former in 1952 [Nishimura H. Chem. Today 1998;323:60-66] was found to precede that of the latter by approximately 2 years, thereby indicating that MeHg is the cause of the disaster. This was confirmed by the elevated levels of MeHg in the umbilical cords from residents of the Minamata area [from 0.35 +/- 0.30 (S.D.) ppm in 1952 to 0.96 +/- 0.75 ppm in 1955], the MeHg levels (1.60 +/- 1.00 ppm) in the cords from patients with congenital Minamata disease showing the highest values [P < 0.01 vs. acquired Minamata disease (0.72 +/- 0.65 ppm), mental retardation (0.74 +/- 0.64 ppm), other diseases (0.22 +/- 0.15 ppm), and no symptoms (0.28 +/- 0.20 ppm), respectively]. Thus, in order to fill a gap, which extends over a long period of time, in studies on environmental Hg pollution, umbilical cord samples were considered to be a useful tool.

Chemical characterization of synthetic cannabinoids by electrospray ionization FT-ICR mass spectrometry.

PubMed

Kill, Jade B; Oliveira, Izabela F; Tose, Lilian V; Costa, Helber B; Kuster, Ricardo M; Machado, Leandro F; Correia, Radigya M; Rodrigues, Rayza R T; Vasconcellos, Géssica A; Vaz, Boniek G; Romão, Wanderson

2016-09-01

The synthetic cannabinoids (SCs) represent the most recent advent of the new psychotropic substances (NPS) and has become popularly known to mitigate the effects of the Δ(9)-THC. The SCs are dissolved in organic solvents and sprayed in a dry herbal blend. However, little information is reported on active ingredients of SCs as well as the excipients or diluents added to the herbal blend. In this work, the direct infusion electrospray ionization Fourier transform ion cyclotron mass spectrometry technique (ESI-FT-ICR MS) was applied to explore the chemical composition of nine samples of herbal extract blends, where a total of 11 SCs (UR-144, JWH-073, XLR-11, JWH-250, JWH-122, AM-2201, AKB48, JWH-210, JWH-081, MAM-2201 and 5F-AKB48) were identified in the positive ionization mode, ESI(+), and other 44 chemical species (saturated and unsaturated fatty acids, sugars, flavonoids, etc.) were detected in the negative ionization mode, ESI(-). Additionally, CID experiments were performed, and fragmentation pathways were proposed to identify the connectivity of SCs. Thus, the direct infusion ESI-FT-ICR MS technique is a powerful tool in forensic chemistry that enables the rapid and unequivocal way for the determination of molecular formula, the degree of unsaturation (DBE-double bond equivalent) and exact mass (<1ppm) of a total of 55 chemical species without the prior separation step. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Method of separation of yttrium-90 from strontium-90

DOEpatents

Bray, Lane A.; Wester, Dennis W.

1996-01-01

A method for purifying Y-90 from a Sr-90/Y-90 "cow" wherein raw Sr-90/Y-90 source containing impurities is obtained from nuclear material reprocessing. Raw Sr-90/Y-90 source is purified to a fresh Sr-90/Y-90 source "cow" by removing impurities by addition of sodium hydroxide and by removing Cs-137 by further addition of sodium carbonate. The "cow" is set aside to allow ingrowth. An HDEHP organic extractant is obtained from a commercial supplier and further purified by saturation with Cu(II), precipitation with acetone, and washing with nitric acid. The "cow" is then dissolved in nitric acid and the purified HDEHP is washed with nitric acid and scrubbed with either nitric or hydrochloric acid. The dissolved "cow" and scrubbed HDEHP are combined in an organic extraction, separating Y-90 from Sr-90, resulting in a Sr-90/Y-90 concentration ratio of not more than 10(E-7), and a metal impurity concentration of not more than 10 ppm per curie of Y-90. The separated Y-90 may then be prepared for delivery.

Method of separation of yttrium-90 from strontium-90

DOEpatents

Bray, L.A.; Wester, D.W.

1996-04-30

A method is described for purifying Y-90 from a Sr-90/Y-90 ``cow`` wherein raw Sr-90/Y-90 source containing impurities is obtained from nuclear material reprocessing. Raw Sr-90/Y-90 source is purified to a fresh Sr-90/Y-90 source ``cow`` by removing impurities by addition of sodium hydroxide and by removing Cs-137 by further addition of sodium carbonate. The ``cow`` is set aside to allow ingrowth. An HDEHP organic extractant is obtained from a commercial supplier and further purified by saturation with Cu(II), precipitation with acetone, and washing with nitric acid. The ``cow`` is then dissolved in nitric acid and the purified HDEHP is washed with nitric acid and scrubbed with either nitric or hydrochloric acid. The dissolved ``cow`` and scrubbed HDEHP are combined in an organic extraction, separating Y-90 from Sr-90, resulting in a Sr-90/Y-90 concentration ratio of not more than 10(E-7), and a metal impurity concentration of not more than 10 ppm per curie of Y-90. The separated Y-90 may then be prepared for delivery. 1 fig.

Distribution of dissolved zinc in the western and central subarctic North Pacific

NASA Astrophysics Data System (ADS)

Kim, T.; Obata, H.; Gamo, T.

2016-02-01

Zinc (Zn) is an essential micronutrient for bacteria and phytoplankton in the ocean as it plays an important role in numerous enzyme systems involved in various metabolic processes. However, large-scale distributions of total dissolved Zn in the subarctic North Pacific have not been investigated yet. In this study, we investigated the distributions of total dissolved Zn to understand biogeochemical cycling of Zn in the western and central subarctic North Pacific as a Japanese GEOTRACES project. Seawater samples were collected during the R/V Hakuho-maru KH-12-4 GEOTRACES GP 02 cruise (from August to October 2012), by using acid-cleaned Teflon-coated X-type Niskin samplers. Total dissolved Zn in seawater was determined using cathodic stripping voltammetry (CSV) after UV-digestion. In this study, total dissolved Zn concentrations in the western and central subarctic North Pacific commonly showed Zn increase from surface to approximately 400-500 m, just above the oxygen minimum layer. However, in the western subarctic North Pacific, relatively higher Zn concentrations have also been observed at intermediate depths (800-1200 m), in comparison with those observed in deep waters. The relationship between Zn and Si in the western subarctic North Pacific showed that Zn is slightly enriched at intermediate depths. These results may indicate that there are additional sources of Zn to intermediate water of the western subarctic North Pacific.

Distribution and composition of dissolved amino acids in seawater at the Yap Trench

NASA Astrophysics Data System (ADS)

Yan, Y.; Xie, L.; Sun, C.; Yang, G.; Ding, H.

2017-12-01

The distributions and compositions of total hydrolyzed amino acids ( THAA) , dissolved combined amino acids ( DCAA) and dissolved free amino acids ( DFAA) were investigated after analyzing seawater samples collected from different depths by CTD and from the sediment-seawater interface by the Jiaolong submersible, at 4 stations located in the Yap Trench in June, 2016. The results showed that the average concentration of THAA was (2.44±0.85) μmol /L, while the average concentrations of DCAA and DFAA were (1.97±0.82) μmol /L and (0.47±0.34)μmol /L, respectively.The concentrations of THAA and DCAA displayed a decreasing trend from surface layer to deep layer. In the vertical distribution, the concentrations of THAA varied differently in superficial layer (above 1000 meters). THAA, DFAA and DCAA had a similar concentrations below 1000 meter depth. In the study area, major constituents of dissolved amino acids were methionine, threonine , histidine, glutamic acid , valine and glycine. At the Yap Trench, neutral dissolved amino acids were dominant in total dissolved amino acids. The trend of vertical distributions of various types of THAA, DFAA, and DCAA were similar with the total THAA, DFAA, and DCAA. In sediment-seawater interface, the seawater in the northwest of the trench has high concentrations of THAA and DCAA, while the concentrations of DFAA were similar in the seawater at the sediment-seawater interface.

76 FR 76161 - Clean Water Act Section 303(d): Availability of Three Total Maximum Daily Loads (TMDLs) in Louisiana

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-06

... Ponchatoula Creek and Dissolved Ponchatoula River. oxygen. 041201 Bayou Labranche-- Dissolved Headwaters to Lake oxygen. Pontchartrain (Scenic) (Estuarine). 041805 Lake Borgne Canal (Violet Dissolved Canal)--MS River siphon oxygen. at Violet to Bayou Dupre (Scenic) (Estuarine). The EPA requests the public provide...

Drought effects on water quality in the South Platte River Basin, Colorado

USGS Publications Warehouse

Sprague, Lori A.

2005-01-01

Twenty-three stream sites representing a range of forested, agricultural, and urban land uses were sampled in the South Platte River Basin of Colorado from July through September 2002 to characterize water quality during drought conditions. With a few exceptions, dissolved ammonia, Kjeldahl nitrogen, total phosphorus, and dissolved orthophosphate concentrations were similar to seasonal historical levels in all land use areas during the drought. At some agricultural sites, decreased dilution of irrigation return flow may have contributed to higher concentrations of some nutrient species, increased primary productivity, and higher dissolved oxygen concentrations. At some urban sites, decreased dilution of base flow and wastewater treatment plant effluent may have contributed to higher dissolved nitrite-plus-nitrate concentrations, increased primary productivity, and higher dissolved oxygen concentrations. Total pesticide concentrations in urban and agricultural areas were not consistently higher or lower during the drought. At most forested sites, decreased dilution of ground water-derived calcium bicarbonate type base flow likely led to elevated pH and specific-conductance values. Water temperatures at many of the forested sites also were higher, contributing to lower dissolved oxygen concentrations during the drought.

Enhanced coagulation for improving coagulation performance and reducing residual aluminum combining polyaluminum chloride with diatomite.

PubMed

Hu, Wenchao; Wu, Chunde

2016-01-01

The feasibility of using enhanced coagulation, which combined polyaluminum chloride (PAC) with diatomite for improving coagulation performance and reducing the residual aluminum (Al), was discussed. The effects of PAC and diatomite dosage on the coagulation performance and residual Al were mainly investigated. Results demonstrated that the removal efficiencies of turbidity, dissolved organic carbon (DOC), and UV254 were significantly improved by the enhanced coagulation, compared with PAC coagulation alone. Meaningfully, the five forms of residual Al (total Al (TAl), total dissolved Al (TDAl), dissolved organic Al (DOAl), dissolved monomeric Al (DMAl), and dissolved organic monomeric Al (DOMAl)) all had different degrees of reduction in the presence of diatomite and achieved the lowest concentrations (0.185, 0.06, 0.053, 0.014, and 0 mg L(-1), respectively) at a PAC dose of 15 mg L(-1) and diatomite dose of 40 mg L(-1). In addition, when PAC was used as coagulant, the majority of residual Al existed in dissolved form (about 31.14-70.16%), and the content of DOMAl was small in the DMAl.

Using Citrus aurantifolia essential oil for the potential biocontrol of Colocasia esculenta (taro) leaf blight caused by Phytophthora colocasiae.

PubMed

Tchameni, Séverin Nguemezi; Mbiakeu, Staelle Njamou; Sameza, Modeste Lambert; Jazet, Pierre Michel Dongmo; Tchoumbougnang, François

2017-11-17

The aim of this work was to evaluate the antimicrobial activities of leaves and epicarp of Citrus aurantifolia essential oil against Phytophthora colocasiae, the causative agent of taro leaf blight. Oils were extracted by hydrodistillation, and their chemical composition was determined by gas chromatography and gas chromatography coupled with mass spectrometry. Antimicrobial activities of oils were tested in vitro against mycelium growth and sporangium production. In situ tests were done on healthy taro leaves, and the necrosis symptoms were evaluated. Results showed that the essential oil extraction yields from leaves and epicarp were 0.61 and 0.36%, respectively. Limonene (48.96%), bornyl acetate (14.18%), geraniol (10.53%), geranial (3.93%), and myrcene (3.14%) were the main components in leaf oil, while limonene (59.09%), cis-hydrate sabinene (7.53%), geranial (5.61%), myrtenol (5.02%), and terpinen-4-ol (3.48%) were the main components in epicarp oil. Both oils exhibited antimicrobial activities with total inhibition of the mycelium growth at 500 and 900 ppm for leaf and epicarp, respectively. The highest inhibitory concentration of sporangium production was 400 (72.84%) and 800 ppm (80.65%) for leaf and epicarp oil, respectively. For the standard fungicide (metalaxyl), the total inhibition value of mycelial growth and sporangium production was 750 ppm. In situ tests showed that, at 5000 ppm, total inhibition (100%) was obtained for a preventive test, while 50% of the inhibition was observed for a curative test when leaf oil was applied. When epicarp essential oil was applied at 5000 ppm, 47.5 and 16.66% of the reduction of leaf necrosis were observed for the preventive and curative test, respectively. There were positive correlations between both the oil concentration and the reduction of necrosis caused by P. colocasiae. These findings suggest that the C. aurantifolia essential oil could serve as an eco-friendly biocontrol for the management of taro leaf blight.

Effect of cobalt supplementation and fractionation on the biological response in the biomethanization of Olive Mill Solid Waste.

PubMed

Pinto-Ibieta, F; Serrano, A; Jeison, D; Borja, R; Fermoso, F G

2016-07-01

Due to the low trace metals concentration in the Olive Mill Solid Waste (OMSW), a proposed strategy to improve its biomethanization is the supplementation of key metals to enhance the microorganism activity. Among essential trace metals, cobalt has been reported to have a crucial role in anaerobic degradation. This study evaluates the effect of cobalt supplementation to OMSW, focusing on the connection between fractionation of cobalt in the system and the biological response. The highest biological responses was found in a range from 0.018 to 0.035mg/L of dissolved cobalt (0.24-0.65mg total cobalt/L), reaching improvements up to 23% and 30% in the methane production rate and the methane yield coefficient, respectively. It was found that the dissolved cobalt fraction is more accurately related with the biological response than the total cobalt. The total cobalt is distorted by the contribution of dissolved and non-dissolved inert fractions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Response surface modeling for optimization heterocatalytic Fenton oxidation of persistence organic pollution in high total dissolved solid containing wastewater.

PubMed

Sekaran, G; Karthikeyan, S; Boopathy, R; Maharaja, P; Gupta, V K; Anandan, C

2014-01-01

The rice-husk-based mesoporous activated carbon (MAC) used in this study was precarbonized and activated using phosphoric acid. N2 adsorption/desorption isotherm, X-ray powder diffraction, electron spin resonance, X-ray photoelectron spectroscopy and scanning electron microscopy, transmission electron microscopy, (29)Si-NMR spectroscopy, and diffuse reflectance spectroscopy were used to characterize the MAC. The tannery wastewater carrying high total dissolved solids (TDS) discharged from leather industry lacks biodegradability despite the presence of dissolved protein. This paper demonstrates the application of free electron-rich MAC as heterogeneous catalyst along with Fenton reagent for the oxidation of persistence organic compounds in high TDS wastewater. The heterogeneous Fenton oxidation of the pretreated wastewater at optimum pH (3.5), H2O2 (4 mmol/L), FeSO4[Symbol: see text]7H2O (0.2 mmol/L), and time (4 h) removed chemical oxygen demand, biochemical oxygen demand, total organic carbon and dissolved protein by 86, 91, 83, and 90%, respectively.

Total mercury concentrations in lionfish (Pterois volitans/miles) from the Florida Keys National Marine Sanctuary, USA

USGS Publications Warehouse

Huge, Dane H.; Schofield, Pamela J.; Jacoby, Charles A.; Frazer, Thomas K.

2014-01-01

Strategies to control invasive lionfish in the western Atlantic and Caribbean are likely to include harvest and consumption. Until this report, total mercury concentrations had been documented only for lionfish from Jamaica, and changes in concentrations with increasing fish size had not been evaluated. In the Florida Keys, total mercury concentrations in dorsal muscle tissue from 107 lionfish ranged from 0.03 to 0.48 ppm, with all concentrations being less than the regulatory threshold for limited consumption. Mercury concentrations did not vary consistently with standard lengths or wet weights of lionfish. In 2010, lionfish from the upper Keys had mean concentrations that were 0.03–0.04 ppm higher than lionfish from the middle Keys, but mean concentrations did not differ consistently among years and locations. Overall, total mercury concentrations in lionfish were lower than those in several predatory fishes that support commercial and recreational fisheries in Florida.

Incidence and impact of prosthesis-patient mismatch after transcatheter aortic valve implantation.

PubMed

Bleiziffer, Sabine; Hettich, Ina; Hutter, Andrea; Wagner, Anke; Deutsch, Marcus-André; Piazza, Nicolo; Lange, Rüdiger

2013-05-01

The study aim was to investigate the incidence of patient-prosthesis mismatch (PPM) with new catheter valves, and its influence on the patients' clinical state. At present, few echocardiographic data are available on the incidence and impact of PPM with the CoreValve and Sapien prostheses for transcatheter aortic valve implantation (TAVI). The reliability of effective orifice area (EOA) measurements was assured by awaiting an interval of six months after TAVI. Of 256 survivors after TAVI, 149 complete echocardiographic data sets were available for the assessment of the indexed EOA (iEOA). In total, 106 CoreValve prostheses and 43 Sapien prostheses were implanted in this high-risk cohort (mean age 81 +/- 6 years, mean logistic EuroSCORE 20 +/- 13%). The overall incidence of PPM (iEOA < 0.85 cm2/m2) was 61%. Patients with a larger body surface area were more likely to develop PPM (p = 0.001), while the prosthesis type, native annulus diameter, preoperative EOA, gender and prosthesis size had no influence. The mean aortic gradient was significantly higher in patients with PPM. A reduction in the left ventricular end-diastolic diameter was seen in all patients, without significant differences between groups. There were no differences in postoperative NYHA class or self-assessed health state between patients with or without PPM. PPM was common after TAVI in the presented cohort, presumably because the native calcium masses narrow the outflow area available for blood flow. As expected for low gradients, there was no impairment of left ventricular dimension regression or clinical state of the patients, even if severe PPM was present. Based on the presented data, it is assumed that PPM might be less relevant in TAVI patients.

Effects of drinking water monochloramine on lipid and thyroid metabolism in healthy men.

PubMed Central

Wones, R G; Deck, C C; Stadler, B; Roark, S; Hogg, E; Frohman, L A

1993-01-01

The purpose of this study was to determine whether a 4-week consumption of 1.5L per day of drinking water containing monochloramine at a concentration of 2 ppm (ppm = mg/L) or 15 ppm under controlled conditions would alter parameters of lipid or thyroid metabolism in healthy men. Forty-eight men completed an 8-week protocol during which diet (600 mg cholesterol per day, 40% calories as fat) and other factors known to affect lipid metabolism were controlled. During the first 4 weeks of the protocol, all subjects consumed distilled water. During the second 4 weeks, one-third of the subjects were assigned randomly to drink 1.5 L per day of water containing 2 ppm of monochloramine, to drink 1.5 L per day of water containing 15 ppm monochloramine, or to continue drinking distilled water. Four blood samples were collected from each subject at the end of each 4-week study period. Subjects drinking monochloramine at a concentration of 2 ppm showed no significant changes in total cholesterol, triglycerides, HDL cholesterol, LDL cholesterol, apolipoproteins A1, A2, or B when compared to the distilled water group. Parameters of thyroid function also were unchanged by exposure to monochloramine at this concentration. However, subjects drinking monochloramine at a concentration of 15 ppm experienced an increase in the level of apolipoprotein B. Other parameters of lipid and thyroid metabolism did not change. We conclude that consumption of drinking water containing 2 ppm of monochloramine does not alter parameters of lipid and thyroid metabolism in healthy men. Consumption of water containing 15 ppm monochloramine may be associated with increased levels of plasma apolipoprotein B. PMID:8319653

CHEMOPREVENTIVE EFFICACY OF NAPROXEN AND NO-NAPROXEN IN RODENT MODELS OF COLON, URINARY BLADDER, AND MAMMARY CANCERS

PubMed Central

Steele, Vernon E.; Rao, Chinthalapally V.; Zhang, Yuting; Patlolla, Jagan; Boring, Daniel; Kopelovich, Levy; Juliana, M. Margaret; Grubbs, Clinton J.; Lubet, Ronald A.

2009-01-01

Nonsteroidal anti-inflammatory drugs (NSAIDs) have been highly effective in preventing colon, urinary bladder, and skin cancer preclinically; and also in clinical trials of colon adenoma formation. However, certain NSAIDs cause gastrointestinal (GI) ulceration and may increase cardiovascular (CV) events. Naproxen appears to cause the lowest CV events of the common NSAIDs other than aspirin. NO-naproxen was tested based on the finding that adding a nitric oxide (NO) group to NSAIDs may help alleviate GI toxicity. In the azoxymethane (AOM)-induced rat colon aberrant crypt foci (ACF) model, naproxen administered at 200 and 400 ppm in the diet reduced mean ACFs in the colon by about 45–60%, respectively. NO-naproxen was likewise administered in the diet at roughly equimolar doses (300 and 600 ppm), and reduced total ACF by 20–40%, respectively. In the hydroxybutyl (butyl) nitrosamine (OH-BBN) rat urinary bladder cancer model, NO-naproxen was given at 183 ppm or 550 ppm in the diet, and naproxen at 128 ppm. The NO-naproxen groups had 77% and 73% decreases, respectively, in the development of large urinary bladder tumors, while the 128 ppm naproxen group also showed a strong decrease (69%). If treatments were started three months after OH-BBN, NO-naproxen (550 ppm) and naproxen (400 ppm) were also highly effective (86–94% decreases). In the methylnitrosourea (MNU)-induced mammary cancer model in rats, NO-naproxen and naproxen showed non-significant inhibitions (12 and 24%) at 550 and 400 ppm, respectively. These data show that both naproxen and NO-naproxen are effective agents against urinary bladder and colon, but not mammary, carcinogenesis. PMID:19892664

Combined effects of hydrographic structure and iron and copper availability on the phytoplankton growth in Terra Nova Bay Polynya (Ross Sea, Antarctica)

NASA Astrophysics Data System (ADS)

Rivaro, Paola; Luisa Abelmoschi, Maria; Grotti, Marco; Ianni, Carmela; Magi, Emanuele; Margiotta, Francesca; Massolo, Serena; Saggiomo, Vincenzo

2012-04-01

Surface water (<100 m) samples were collected from the Terra Nova Bay polynya region of the Ross Sea (Antarctica) in January 2006, with the aim of evaluating the individual and combined effects of hydrographic structure, iron and copper concentration and availability on the phytoplankton growth. The measurements were conducted within the framework of the Climatic Long Term Interaction for the Mass-balance in Antarctica (CLIMA) Project of the Programma Nazionale di Ricerca in Antartide activities. Dissolved oxygen, nutrients, phytoplankton pigments and concentration and complexation of dissolved trace metals were determined. Experimental data were elaborated by Principal Component Analysis (PCA). As a result of solar heating and freshwater inputs from melting sea-ice, the water column was strongly stratified with an Upper Mixed Layer 4-16 m deep. The integrated Chl a in the layer 0-100 m ranged from 60 mg m-2 to 235 mg m-2, with a mean value of 138 mg m-2. The pigment analysis showed that diatoms dominated the phytoplankton assemblage. Major nutrients were generally high, with the lowest concentration at the surface and they were never fully depleted. The Si:N drawdown ratio was close to the expected value of 1 for Fe-replete diatoms. We evaluated both the total and the labile dissolved fraction of Fe and Cu. The labile fraction was operationally defined by employing the chelating resin Chelex-100, which retains free and loosely bound trace metal species. The total dissolved Fe ranged from 0.48 to 3.02 nM, while the total dissolved Cu from 3.68 to 6.84 nM. The dissolved labile Fe ranged from below the detection limit (0.15 nM) to 1.22 nM, and the dissolved labile Cu from 0.31 to 1.59 nM, respectively. The labile fractions measured at 20 m were significantly lower than values in 40-100 m samples. As two stations were re-sampled 5 days later, we evaluated the short-term variability of the physical and biogeochemical properties. In particular, in a re-sampled station at 20 m, the total dissolved Fe increased and the total dissolved Cu decreased, while their labile fraction was relatively steady. As a result of the increase in total Fe, the percentage of the labile Fe decreased. An increase of the Si:N, Si:P and Si:FUCO ratios was measured also in the re-sampled station. On this basis, we speculated that a switch from a Fe-replete to a Fe-deplete condition was occurring.

Simulated effects of proposed Arkansas Valley Conduit on hydrodynamics and water quality for projected demands through 2070, Pueblo Reservoir, southeastern Colorado

USGS Publications Warehouse

Ortiz, Roderick F.

2013-01-01

The purpose of the Arkansas Valley Conduit (AVC) is to deliver water for municipal and industrial use within the boundaries of the Southeastern Colorado Water Conservancy District. Water supplied through the AVC would serve two needs: (1) to supplement or replace existing poor-quality water to communities downstream from Pueblo Reservoir; and (2) to meet a portion of the AVC participants’ projected water demands through 2070. The Bureau of Reclamation (Reclamation) initiated an Environmental Impact Statement (EIS) to address the potential environmental consequences associated with constructing and operating the proposed AVC, entering into a conveyance contract for the Pueblo Dam north-south outlet works interconnect (Interconnect), and entering into a long-term excess capacity master contract (Master Contract). Operational changes, as a result of implementation of proposed EIS alternatives, could change the hydrodynamics and water-quality conditions in Pueblo Reservoir. An interagency agreement was initiated between Reclamation and the U.S. Geological Survey to accurately simulate hydrodynamics and water quality in Pueblo Reservoir for projected demands associated with four of the seven proposed EIS alternatives. The four alternatives submitted to the USGS for scenario simulation included various combinations (action or no action) of the proposed Arkansas Valley Conduit, Master Contract, and Interconnect options. The four alternatives were the No Action, Comanche South, Joint Use Pipeline North, and Master Contract Only. Additionally, scenario simulations were done that represented existing conditions (Existing Conditions scenario) in Pueblo Reservoir. Water-surface elevations, water temperature, dissolved oxygen, dissolved solids, dissolved ammonia, dissolved nitrate, total phosphorus, total iron, and algal biomass (measured as chlorophyll-a) were simulated. Each of the scenarios was simulated for three contiguous water years representing a wet, average, and dry annual hydrologic cycle. Each selected simulation scenario also was evaluated for differences in direct/indirect effects and cumulative effects on a particular scenario. Analysis of the results for the direct/indirect- and cumulative-effects analyses indicated that, in general, the results were similar for most of the scenarios and comparisons in this report focused on results from the direct/indirect-effects analyses. Scenario simulations that represented existing conditions in Pueblo Reservoir were compared to the No Action scenario to assess changes in water quality from current demands (2006) to projected demands in 2070. Overall, comparisons of the results between the Existing Conditions and the No Action scenarios for water-surface elevations, water temperature, and dissolved oxygen, dissolved solids, dissolved ammonia, dissolved nitrate, total phosphorus, and total iron concentrations indicated that the annual median values generally were similar for all three simulated years. Additionally, algal groups and chlorophyll-a concentrations (algal biomass) were similar for the Existing Conditions and the No Action scenarios at site 7B in the epilimnion for the simulated period (Water Year 2000 through 2002). The No Action scenario also was compared individually to the Comanche South, Joint Use Pipeline North, and Master Contract Only scenarios. These comparisons were made to describe changes in the annual median, 85th percentile, or 15th percentile concentration between the No Action scenario and each of the other three simulation scenarios. Simulated water-surface elevations, water temperature, dissolved oxygen, dissolved solids, dissolved ammonia, dissolved nitrate, total phosphorus, total iron, algal groups, and chlorophyll-a concentrations in Pueblo Reservoir generally were similar between the No Action scenario and each of the other three simulation scenarios.

Simulation of streamflow and water quality in the Leon Creek watershed, Bexar County, Texas, 1997-2004

USGS Publications Warehouse

Ockerman, Darwin J.; Roussel, Meghan C.

2009-01-01

The U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers and the San Antonio River Authority, configured, calibrated, and tested a Hydrological Simulation Program ? FORTRAN watershed model for the approximately 238-square-mile Leon Creek watershed in Bexar County, Texas, and used the model to simulate streamflow and water quality (focusing on loads and yields of selected constituents). Streamflow in the model was calibrated and tested with available data from five U.S. Geological Survey streamflow-gaging stations for 1997-2004. Simulated streamflow volumes closely matched measured streamflow volumes at all streamflow-gaging stations. Total simulated streamflow volumes were within 10 percent of measured values. Streamflow volumes are greatly influenced by large storms. Two months that included major floods accounted for about 50 percent of all the streamflow measured at the most downstream gaging station during 1997-2004. Water-quality properties and constituents (water temperature, dissolved oxygen, suspended sediment, dissolved ammonia nitrogen, dissolved nitrate nitrogen, and dissolved and total lead and zinc) in the model were calibrated using available data from 13 sites in and near the Leon Creek watershed for varying periods of record during 1992-2005. Average simulated daily mean water temperature and dissolved oxygen at the most downstream gaging station during 1997-2000 were within 1 percent of average measured daily mean water temperature and dissolved oxygen. Simulated suspended-sediment load at the most downstream gaging station during 2001-04 (excluding July 2002 because of major storms) was 77,700 tons compared with 74,600 tons estimated from a streamflow-load regression relation (coefficient of determination = .869). Simulated concentrations of dissolved ammonia nitrogen and dissolved nitrate nitrogen closely matched measured concentrations after calibration. At the most downstream gaging station, average simulated monthly mean concentrations of dissolved ammonia and nitrate concentrations during 1997-2004 were 0.03 and 0.37 milligram per liter, respectively. For the most downstream station, the measured and simulated concentrations of dissolved and total lead and zinc for stormflows during 1993-97 after calibration do not match particularly closely. For base-flow conditions during 1997-2004 at the most downstream station, the simulated/measured match is better. For example, median simulated concentration of total lead (for 2,041 days) was 0.96 microgram per liter, and median measured concentration (for nine samples) of total lead was 1.0 microgram per liter. To demonstrate an application of the Leon Creek watershed model, streamflow constituent loads and yields for suspended sediment, dissolved nitrate nitrogen, and total lead were simulated at the mouth of Leon Creek (outlet of the watershed) for 1997-2004. The average suspended-sediment load was 51,800 tons per year. The average suspended-sediment yield was 0.34 ton per acre per year. The average load of dissolved nitrate at the outlet of the watershed was 802 tons per year. The corresponding yield was 10.5 pounds per acre per year. The average load of lead at the outlet was 3,900 pounds per year. The average lead yield was 0.026 pound per acre per year. The degree to which available rainfall data represent actual rainfall is potentially the most serious source of measurement error associated with the Leon Creek model. Major storms contribute most of the streamflow loads for certain constituents. For example, the three largest stormflows contributed about 64 percent of the entire suspended-sediment load at the most downstream station during 1997-2004.

Extractability, plant yield and toxicity thresholds for boron in compost

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brinton, W.F.; Evans, E.; Blewett, C.

Boron (B) is a trace element essential to crop growth in small soil concentrations (0.2-1.5ppm), yet may produce plant toxicity symptoms readily as the amount in the soil solution increases over 2ppm. Our study examined commercial compost made with coal fly-ash used to prepare growing media for cultivars of varying sensitivity (corn, beans, cucumber, peas). We examined total vs. extractable boron content and relate final visual symptoms of B-toxicity to yields and tissue concentrations. Visual toxicity effects included tip burn (corn), leaf mottling and necrosis (beans and peas) and leaf mottling and cupping (cucumbers). Fly ash added to compost increasedmore » hot-water soluble (HWS) B in proportion to rate and in dependence on pH, with 30% and 10% of total-B expressed as HWS-B at a media pH of 6 and 7.5, respectively. Biomass for bean and cucumber was significantly reduced by 45 to 55%, respectively, by addition of 33% fly-ash compost to growing media (28ppm total-B) while plant tissue-B increased by 6- to 4-fold, respectively. Economic yield depressions in compost media are evident for all crops and appeared at levels of HWS-B in compost media exceeding 5 ppm. The study underscores the need for careful management of exogenous factors that may be present in composts and suggests detailed understanding of media-pH and cultivar preferences may be required in preparation of growing media in order to reduce potential negative growth effects.« less

Proliferation and morphological transformation of RMK cells exposed to hydroquinine containing ionomers.

PubMed

Harvey, Veronica; Benghuzzi, Hamed; Tucci, Michell; Puckett, Aaron; Cason, Zelma

2002-01-01

Recent research in our laboratories has been directed towards the development of ionomeric polymers and monomers for use in biomedical applications such as adhesives, drug delivery matrices and tissue scaffolds. The chemical Hydroquinone (HQ) aids as a stabilizer and represents a major component in the development of the ionomers. However, hydroquinone in high concentration has the potential to initiate carcinogenic effects on cells. The curing reactions are based on free radical chemistry that require a radical scavenger, ascorbic acid (Asc) to adjust working and setting times and shelf-life stability. The few studies published on HQ have suggested that high dosages of HQ may stimulate apoptosis as well as an increased cellular leakage, however the effect of HQ on the biocompatability is unknown. Therefore the objectives of this study were to measure the functional capacity, cell proliferation and structural integrity of Rhesus monkey kidney epithelial (RMK) cells exposed to ionomer formulations containing 4 different levels of HQ. A total of 90 tubes of RMK (40,000 cells per tube) cells were divided equally into five equal groups. Group I served as a control and group II-V were subjected to ionomers containing 0, 500, 1000, and 2000 ppm HQ. Cell numbers, morphology, cellular and supermatant MDA levels, and total protein analysis were performed. The results suggest: (I) All ionomer groups increased cellular proliferation except for the 2000 ppm HQ group, (II) MDA levels were increased in cells containing 2000 ppm HQ at 24 hours; and 0 ppm at 48 hours. It may be concluded that HQ concentrations over 1000 ppm may adversely affect biocompatability.

Toxicity and oxidative stress of different forms of organic selenium and dietary protein in mallard ducklings

USGS Publications Warehouse

Hoffman, D.J.; Heinz, G.H.; LeCaptain, L.J.; Eisemann, J.D.; Pendleton, G.W.

1996-01-01

Concentrations of over 100 ppm (mg/kg) selenium (Se) have been found in aquatic plants and insects associated with irrigation drainwater and toxicity to fish and wildlife. Composition of diet for wild ducklings may vary in selenium-contaminated environments. Earlier studies have compared toxicities and oxidative stress of Se as selenite to those of seleno-DL-methionine (DL) in mallards (Anas platyrhynchos). This study compares DL, seleno-L-methionine (L), selenized yeast (Y) and selenized wheat (W). Day-old mallard ducklings received an untreated diet (controls) containing 75% wheat (22% protein) or the same diet containing 15 or 30 ppm Se in the above forms except for 30 ppm Se as W. After 2 weeks blood and liver samples were collected for biochemical assays and Se analysis. All forms of selenium caused significant increases in plasma and hepatic glutathione peroxidase activities. Se as L at 30 ppm in the diet was the most toxic form, resulting in high mortality (64%) and impaired growth (>50%) in survivors and the greatest increase in ratio of oxidized to reduced hepatic glutathione (GSH). Se as both L and DL decreased the concentrations of hepatic GSH and total thiols. Se as Y accumulated the least in liver (approximately 50% of other forms) and had less effect on GSH and total thiols. In a second experiment, in which the basal diet was a commercial duck feed (22 % protein), survival was not affected by 30 ppm Se as DL, L, or Y and oxidative effects on GSH metabolism were less pronounced than with the wheat diet.

Relation of stream quality to streamflow, and estimated loads of selected water-quality constituents in the James and Rappahannock rivers near the fall line of Virginia, July 1988 through June 1990

USGS Publications Warehouse

Belval, D.L.; Campbell, J.P.; Woodside, M.D.

1994-01-01

This report presents the results of a study by the U.S. Geological Survey, in cooperation with the Virginia Department of Environmental Quality-- Division of Intergovernmental Coordination to monitor and estimate loads of selected nutrients and suspended solids discharged to Chesapeake Bay from two major tributaries in Virginia. From July 1988 through June 1990, monitoring consisted of collecting depth-integrated, cross-sectional samples from the James and Rappahannock Rivers during storm- flow conditions and at scheduled intervals. Water- quality constituents that were monitored included total suspended solids (residue, total at 105 degrees Celsius), dissolved nitrite plus nitrate, dissolved ammonia, total Kjeldahl nitrogen (ammonia plus organic), total nitrogen, total phosphorus, dissolved orthopohosphorus, total organic carbon, and dissolved silica. Daily mean load estimates of each constituent were computed by month, using a seven-parameter log-linear-regression model that uses variables of time, discharge, and seasonality. Water-quality data and constituent- load estimates are included in the report in tabular and graphic form. The data and load estimates provided in this report will be used to calibrate the computer modeling efforts of the Chesapeake Bay region, evaluate the water quality of the Bay and the major effects on the water quality, and assess the results of best-management practices in Virginia.

Investigating aquifer contamination and groundwater quality in eastern Terai region of Nepal.

PubMed

Mahato, Sanjay; Mahato, Asmita; Karna, Pankaj Kumar; Balmiki, Nisha

2018-05-21

This study aims at assessing the groundwater quality of the three districts of Eastern Terai region of Nepal viz. Morang, Jhapa, Sunsari using physicochemical characteristics and statistical approach so that possible contamination of water reservoir can be understood. pH, temperature, conductivity, turbidity, color, total dissolved solids, fluorides, ammonia, nitrates, chloride, total hardness, calcium hardness, calcium, magnesium, total alkalinity, iron, manganese, arsenic have to be analyzed to know the present status of groundwater quality. Results revealed that the value of analyzed parameters were within the acceptable limits for drinking water recommended by World Health Organization except for pH, turbidity, ammonia and iron. As per Nepal Drinking Water Quality Standards, fluoride and manganese too were not complying with the permissible limit. Electrical conductivity, total dissolved solids, chloride, total hardness, calcium hardness, manganese, and total alkalinity show good positive correlation with major water quality parameters. Calcium, magnesium, total hardness, calcium hardness and total alkalinity greatly influences total dissolved solids and electrical conductivity. ANOVA, Tukey, and clustering highlight the significance of three districts. Groundwater can be considered safe, but there is always a chance of contamination through chemical wastes in the heavily industrialized area of Morang and Sunsari Industrial corridor.

40 CFR Appendix A to Subpart O of... - Regulated Contaminants

Code of Federal Regulations, 2010 CFR

2010-07-01

..., young children, some of the elderly, and people with severely compromised immune systems. Total organic carbon (ppm) TT TT N/A Naturally present in the environment Total organic carbon (TOC) has no health effects. However, total organic carbon provides a medium for the formation of disinfection by products...

Quantitative repeated open application testing with a rinse-off product in methyldibromo glutaronitrile-sensitive patients: results of the IVDK.

PubMed

Heratizadeh, Annice; Killig, Claudia; Worm, Margitta; Soost, Stephanie; Simon, Dagmar; Bauer, Andrea; Mahler, Vera; Schuster, Christian; Szliska, Christiane; Frambach, Yvonne; Eben, Ricarda; Werfel, Thomas; Uter, Wolfgang; Schnuch, Axel

2010-06-01

While the use of methyldibromo glutaronitrile (MDBGN) in leave-on products is clearly associated with high sensitization or elicitation risk, such a clear-cut relation could be questioned with regard to rinse-off products. The objective of this study was to find a maximum non-eliciting concentration for rinse-off products in MDBGN patch test-positive patients. We performed a use-related test [repeated open application test (ROAT)] in patients sensitized to MDBGN with a liquid soap containing three concentrations of MDBGN (50, 200, and 400 p.p.m. MDBGN, respectively). The soap at 50 p.p.m. was used twice daily for 4 weeks. If no reaction of the skin was observed, the product with the next higher concentration was used for another 4 weeks, etc. In total, 32/37 evaluated cases [86.5%; lower exact one-sided 95% confidence limit (CL): 73.7%] did not react to any of the preparations. The remaining reacted as follows: 1/37 reacted to 50 p.p.m., 3/37 to 200 p.p.m., and 1/37 to 400 p.p.m. The cumulative non-response to 50 p.p.m. was 97.3% (lower CL: 87.8%). The majority of subjects sensitized to MDBGN-tolerated rinse-off products containing a maximum concentration of 400 p.p.m. A concentration in rinse-off products in the range of 50 p.p.m. could be regarded as safe for most individuals already sensitized. These concentrations will presumably prevent induction (sensitization) also.

The malaria testing and treatment landscape in the southern Lao People's Democratic Republic (PDR).

PubMed

Phanalasy, Saysana

2017-04-25

In the context of national and regional goals to eliminate malaria by 2030, the Center for Malaria Parasitology and Entomology in the Lao PDR is implementing strategies to ensure all malaria cases are detected and appropriately treated with first-line artemisinin combination therapy, artemether-lumefantrine (AL). Timely and relevant evidence to inform policies and strategies is needed to ensure the most effective and efficient use of resources, and to accelerate progress towards elimination goals. A 2015 outlet survey conducted in five provinces of the southern Lao PDR was the first of its kind to study the total market for malaria treatments and diagnostics. The sub-national outlet survey was designed to describe the market and to assess public and private sector readiness and performance for malaria case management. Additionally, key indicators were estimated among private outlets within districts with and without a Public Private Mix (PPM) programme. Over half of anti-malarial stockists were public sector (65.1%). In the private sector, pharmacies most commonly stocked anti-malarials, although anti-malarials were also found in private health facilities, drug stores, general retailers, and itinerant drug vendors. Nearly all anti-malarial stocking public health facilities had AL (99.5%) and 90.8% had confirmatory testing. Fewer than half of anti-malarial stocking private outlets stocked AL (40.8%) and malaria testing (43.5%). Chloroquine has not been a first-line treatment for Plasmodium falciparum malaria since 2005 and Plasmodium vivax since 2011 yet private sector availability was 77.6% and chloroquine accounted for 62.2% of the total anti-malarial market share. AL and confirmatory testing availability were higher in private outlets in PPM (68.1, 72.6%) versus non-PPM districts (2.5, 12.1%). Chloroquine was available in 63.6% of PPM and 96.7% of non-PPM-district outlets, and was the most commonly distributed anti-malarial among private outlets in both PPM (61.7%) and non-PPM districts (99.1%). Public sector outlets in the southern Lao PDR are typically equipped to test and appropriately treat malaria. There is need to address widespread private sector availability and distribution of chloroquine. The PPM programme has improved private provider readiness to manage malaria according to national guidelines. However, supporting interventions to address provider and consumer behaviours are needed to further drive uptake.

Understanding the Transformation, Speciation, and Hazard Potential of Copper Particles in a Model Septic Tank System using Zebrafish to Monitor the Effluent

PubMed Central

Lin, Sijie; Taylor, Alicia A.; Zhaoxia, Ji; Chang, Chong Hyun; Kinsinger, Nichola M.; Ueng, William; Walker, Sharon L.; Nel, André E.

2015-01-01

Although copper-containing nanoparticles are used in commercial products such as fungicides and bactericides, we presently do not understand the environmental impact on other organisms that may be inadvertently exposed. In this study, we used the zebrafish embryo as a screening tool to study the potential impact of two nano Cu-based materials, CuPRO and Kocide, in comparison to nano-sized and micron-sized Cu and CuO particles in their pristine form (0 – 10 ppm) as well as following their transformation in an experimental wastewater treatment system. This was accomplished by construction of a modeled domestic septic tank system from which effluents could be retrieved at different stages following particle introduction (10 ppm). The Cu speciation in the effluent was identified as non-dissolvable inorganic Cu(H2PO2)2 and non-diffusible organic Cu by X-ray diffraction, inductively coupled plasma mass spectrometry (ICP-MS), diffusive gradients in thin-films (DGT), and Visual MINTEQ software. While the nanoscale materials, including the commercial particles, were clearly more potent (showing 50% hatching interference above 0.5 ppm) than the micron-scale particulates with no effect on hatching up to 10 ppm, the Cu released from the particles in the septic tank underwent transformation into non-bioavailable species that failed to interfere with the function of the zebrafish embryo hatching enzyme. Moreover, we demonstrate that the addition of humic acid, as an organic carbon component, could lead to a dose-dependent decrease in Cu toxicity in our high content zebrafish embryo screening assay. Thus, the use of zebrafish embryo screening, in combination with the effluents obtained from a modeled exposure environment, enables a bioassay approach to follow the change in the speciation, and hazard potential of Cu particles instead of difficult-to-perform direct particle tracking. PMID:25625504

Effects of barium and cadmium on the population development of the marine nematode Rhabditis (Pellioditis) marina.

PubMed

Lira, V F; Santos, G A P; Derycke, S; Larrazabal, M E L; Fonsêca-Genevois, V G; Moens, T

2011-10-01

Offshore oil and gas drilling often involves the use of fluids containing barium and traces of other heavy metals. These may affect the environment, but information on their toxicity to benthic biota remains scant. Here, we present results of a 10-day bioassay with the marine nematode Rhabditis (Pellioditis) marina at different loads of barium (0-10 ,000 ppm nominal concentrations) and cadmium (0-12 ppm) in the range of concentrations reported from drilling-impacted sediments. Barium did not affect the fitness and population development of R. (P.) marina at concentrations up to 300 ppm, but did cause a decrease in population abundance and an increase in development time from concentrations of 400-2000 ppm onwards. Increased mortality occurred at 4800 ppm Ba. For cadmium, LOEC and EC₅₀ values for total population abundance were 2.95 and 8.82 ppm, respectively. Cd concentrations as low as 2.40 to 2.68 caused a decrease in the abundance of adult nematodes, indicating that assays covering more generations would likely demonstrate yet more pronounced population-level effects. Our results indicate that oil and gas drilling activities may potentially have important implications for the meiobenthos through the toxicity of barium and associated metals like cadmium. Copyright © 2011 Elsevier Ltd. All rights reserved.

Methylisothiazolinone testing at 2000 ppm: a prevalent sensitizer for allergic contact dermatitis.

PubMed

Ham, Kaiya; Posso-De Los Rios, Claudia J; Gooderham, Melinda

2015-01-01

Methylchloroisothiazolinone (MCI) and methylisothiazolinone (MI) have been identified as potent allergens. The optimal MI concentration for patch testing for reaction to these agents has not yet been identified, but it has been suggested that testing MI at 2000 ppm may reduce false-negative reactions. The aim of this study was to report allergic reactions to MI and MCI/MI detected in a community dermatology practice setting in Ontario, Canada. The patch test records of patients with suspected allergic contact dermatitis seen between October 2007 and June 2014 were reviewed. We compared positive patch testing before and after December 2011 when a higher MI concentration was used (2000 ppm aqueous) in addition to the baseline series MCI/MI at 100 ppm. A total of 794 patient records were reviewed. There were 38 true-positive reactions to MI or MCI/MI. Of these 38 patients, 26 (68%) were female. We detected an overall increase in the rate of positive patch testing to MCI/MI, MI alone, or both from 3.13% to 7.45% when MI concentration was introduced at 2000 ppm aqueous. Occupational differences existed between sexes. The addition of MI at 2000 ppm to our screening series effectively increased the detection of MI-induced allergic contact dermatitis.

Characterization of Water Quality in Unmonitored Streams in the Mississippi Alluvial Plain, Northwestern Mississippi, May-June 2006

USGS Publications Warehouse

Bryson, Jeannie R.; Coupe, Richard H.; Manning, Michael A.

2007-01-01

The Mississippi Department of Environmental Quality is required to develop restoration and remediation plans for water bodies not meeting their designated uses, as stated in the U.S. Environmental Protection Agency's Clean Water Act section 303(d). The majority of streams in northwestern Mississippi are on the 303(d) list of water-quality limited waters. Agricultural effects on streams in northwestern Mississippi have reduced the number of unimpaired streams (reference streams) for water-quality comparisons. As part of an effort to develop an index to assess impairment, the U.S. Geological Survey collected water samples from 52 stream sites on the 303(d) list during May-June 2006, and analyzed the samples for nutrients and chlorophyll. The data were analyzed by trophic group as determined by total nitrogen concentrations. Seven constituents (nitrite plus nitrate, total Kjeldhal nitrogen, total phosphorus, orthophosphorus, total organic carbon, chlorophyll a, and pheophytina) and four physical property measurements (specific conductance, pH, turbidity, and dissolved oxygen) were determined to be significantly different (p < 0.05) between trophic groups. Total Kjeldhal nitrogen, turbidity, and dissolved oxygen were used as indicators of stream productivity with which to infer stream health. Streams having high total Kjeldhal nitrogen values and high turbidity values along with low dissolved oxygen concentrations were typically eutrophic abundant in nutrients), whereas streams having low total Kjeldhal nitrogen values and low turbidity values along with high dissolved oxygen concentrations were typically oligotrophic (deficient in nutrients).

Oil Spill Field Trial at Sea: Measurements of Benzene Exposure.

PubMed

Gjesteland, Ingrid; Hollund, Bjørg Eli; Kirkeleit, Jorunn; Daling, Per; Bråtveit, Magne

2017-07-01

Characterize personal exposure to airborne hydrocarbons, particularly carcinogenic benzene, during spill of two different fresh crude oils at sea. The study included 22 participants taking part in an «oil on water» field trial in the North Sea. Two types of fresh crude oils (light and heavy) were released six times over two consecutive days followed by different oil spill response methods. The participants were distributed on five boats; three open sampling boats (A, B, and C), one release ship (RS), and one oil recovery (OR) vessel. Assumed personal exposure was assessed a priori, assuming high exposure downwind and close to the oil slick (sampling boats), low exposure further downwind (100-200 m) and upwind from the oil slick (main deck of RS and OR vessel), and background exposure indoors (bridge of RS/OR vessel). Continuous measurements of total volatile organic compounds in isobutylene equivalents were performed with photoionization detectors placed in all five boats. Full-shift personal exposure to benzene, toluene, ethylbenzene, xylenes, naphthalene, and n-hexane was measured with passive thermal desorption tubes. Personal measurements of benzene, averaged over the respective sample duration, on Day 1 showed that participants in the sampling boats (A, B, and C) located downwind and close to the oil slick were highest exposed (0.14-0.59 ppm), followed by participants on the RS main deck (0.02-0.10 ppm) and on the bridge (0.004-0.03 ppm). On Day 2, participants in sampling boat A had high benzene exposure (0.87-1.52 ppm) compared to participants in sampling boat B (0.01-0.02 ppm), on the ships (0.06-0.10 ppm), and on the bridge (0.004-0.01 ppm). Overall, the participants in the sampling boats had the highest exposure to all of the compounds measured. The light crude oil yielded a five times higher concentration of total volatile organic compounds in air in the sampling boats (max 510 ppm) than the heavy crude oil (max 100 ppm) but rapidly declined to <20 ppm within 24 min after release of oil, indicating short periods of exposure. The personal exposure to benzene downwind and close to the oil slick during spills of light crude oil was relatively high, with concentration levels approaching the occupational exposure limits for several participants. For bulk spill scenarios like in this study, cleanup should not be initiated the first 30-60 min to allow for evaporation, while appropriate personal protective equipment should be used in continuous spills when working downwind and close to the oil slick. © The Author 2017. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Heavy Metals in Soil and Salad in the Proximity of Historical Ferroalloy Emission

PubMed Central

Ferri, Roberta; Donna, Filippo; Smith, Donald R.; Guazzetti, Stefano; Zacco, Annalisa; Rizzo, Luigi; Bontempi, Elza; Zimmerman, Neil J.; Lucchini, Roberto G.

2016-01-01

Emissions of manganese (Mn), lead (Pb), iron (Fe), zinc (Zn), copper (Cu) from ferro-alloy operations has taken place in Valcamonica, a pre-Alp valley in the province of Brescia, Italy, for about a century until 2001. Metal concentrations were measured in the soil of local home gardens and in the cultivated vegetables. Soil analysis was carried out using a portable X-Ray Fluorescence (XRF) spectrometer in both surface soil and at 10 cm depth. A subset of soil samples (n = 23) additionally was analysed using the modified BCR sequential extraction method and ICP-OES for intercalibration with XRF (XRF Mn = 1.33 * total OES Mn – 71.8; R = 0.830, p < 0.0001). Samples of salads (Lactuca sativa and Chichorium spp.) were analyzed with a Total Reflection X-Ray Fluorescence (TXRF) technique. Vegetable and soil metal measurements were performed in 59 home gardens of Valcamonica, and compared with 23 gardens from the Garda Lake reference area. Results indicate significantly higher levels of soil Mn (median 986 ppm vs 416 ppm), Pb (median 46.1 ppm vs 30.2 ppm), Fe (median 19,800 ppm vs 13,100 ppm) in the Valcamonica compared to the reference area. Surface soil levels of all metals were significantly higher in surface soil compared to deeper soil, consistent with atmospheric deposition. Significantly higher levels of metals were shown also in lettuce from Valcamonica for Mn (median 53.6 ppm vs 30.2) and Fe (median 153 vs 118). Metals in Chichorium spp. did not differ between the two areas. Surface soil metal levels declined with increasing distance from the closest ferroalloy plant, consistent with plant emissions as the source of elevated soil metal levels. A correlation between Mn concentrations in soil and lettuce was also observed. These data show that historic ferroalloy plant activity, which ended nearly a decade before this study, has contributed to the persistence of increased Mn levels in locally grown vegetables. Further research is needed to assess whether this increase can lead to adverse effects in humans and plants especially for Mn, an essential element that can be toxic in humans when exceeding the homeostatic ranges. PMID:27818841

Biogeochemical cycle of Mercury in an urban stream in Hartford CT

NASA Astrophysics Data System (ADS)

Aragon-jose, A. T.; Bushey, J. T.; Perkins, C.; Mendes, M.; Ulatowski, G.

2012-12-01

Mercury (Hg) toxicity and the potential for bioaccumulation in the food chain result in exposure risk even at low Hg levels. The presence of urban activities can substantially alter Hg fate and transport mechanisms and Hg biogeochemical cycles. Urban watersheds are characterized by high imperviousness and some may even be impacted by combined sewer overflows, both being fundamental factors contributing to Hg loading, mobilization, and shifts in bioavailability in urban watersheds. Research is still needed to characterize the fate and dynamics of Hg in urban streams. To address this gap in knowledge, we collected and characterized stream water and suspended sediment samples in the Park River watershed in Hartford, CT (USA) during baseflow and precipitation events. Sampling sites were selected across an urbanization gradient. Water samples are analyzed for total, dissolved, and particulate Hg and methyl Hg (MeHg), major ions (Cl-, NO3-, SO42-)-, total suspended solids (TSS), and dissolved organic carbon (DOC). Our results show that both total and dissolved Hg concentrations increase in the streams during precipitation events, however, the greatest portion of Hg is associated, and consequently transported, with suspended sediments, as suggested by the high correlation coefficient (R2 ~ 0.80) between TSS and total Hg. No significant correlation was observed between dissolved or total Hg and DOC, contrary to the observations in forested systems, which indicates that the sources and mechanisms governing mobilization and transport of dissolved Hg in an urban watershed differ from those at forested systems. However, during select events, a significant portion of Hg flux occurs in the dissolved phase. Unfiltered MeHg samples exhibited a similar pattern relative to the hydrograph to that of total Hg. Concentrations increase during the rising limb with TSS followed by a decrease as the storm progresses. Dissolved MeHg is mostly below our detection limit. Area normalized THg flux is generally higher at the more developed sites for all but the May storm, whereas the opposite trend is observed for MeHg except for the August storm, indicative of different sources of Hg contributing to the stream. To assist in elucidating the potential sources, dissolved organic matter in the water samples was analyzed for specific ultra violet absorbance at 254 nm (SUVA254) and for excitation-emission matrix (EEMs) to assess differences in organic matter loading to the stream. Additionally, Hg association with sediment was analyzed by collecting four sets of suspended sediment samples over 3-month periods at five sites across the watershed to assess potential sediment sources into the stream. Solid samples were analyzed for total carbon, nitrogen, and hydrogen, organic and inorganic carbon, mercury, acid volatile sulfide, chromium reducible sulfide, PAHs, QACs, and select metals.

Determination of the Fate of Dissolved Organic Nitrogen in the Three Wastewater Treatment Plants, Jordan

ERIC Educational Resources Information Center

Wedyan, Mohammed; Al Harahsheh, Ahmed; Qnaisb, Esam

2016-01-01

This research aimed to assess the composition of total dissolved nitrogen (TDN) species, particularly dissolved organic nitrogen (DON), over the traditional wastewater treatment operations in three biological nutrient removal (BNR) wastewater treatment plants (WWTPs) in Jordan. It had been found that the DON percentage was up to 30% of TDN within…

Gene cloning and in vivo characterization of a dibenzothiophene dioxygenase from Xanthobacter polyaromaticivorans.

PubMed

Hirano, Shin-Ichi; Haruki, Mitsuru; Takano, Kazufumi; Imanaka, Tadayuki; Morikawa, Masaaki; Kanaya, Shigenori

2006-02-01

Xanthobacter polyaromaticivorans sp. nov. 127W is a bacterial strain that is capable of degrading a wide range of cyclic aromatic compounds such as dibenzothiophene, biphenyl, naphthalene, anthracene, and phenanthrene even under extremely low oxygen [dissolved oxygen (DO)< or = 0.2 ppm] conditions (Hirano et al., Biosci Biotechnol Biochem 68:557-564, 2004). A major protein fraction carrying dibenzothiophene degradation activity was purified. Based on its partial amino acid sequences, dbdCa gene encoding alpha subunit terminal oxygenase (DbdCa) and its flanking region were cloned and sequenced. A phylogenetic analysis based on the amino acid sequence demonstrates that DbdCa is a member of a terminal oxygenase component of group IV ring-hydroxylating dioxygenases for biphenyls and monocyclic aromatic hydrocarbons, rather than group III dioxygenases for polycyclic aromatic hydrocarbons. Gene disruption in dbdCa abolished almost of the degradation activity against biphenyl, dibenzothiophene, and anthracene. The gene disruption also impaired degradation activity of the strain under extremely low oxygen conditions (DO< or = 0.2 ppm). These results indicate that Dbd from 127W represents a group IV dioxygenase that is functional even under extremely low oxygen conditions.

Hydrocarbon-fuel/combustion-chamber-liner materials compatibility

NASA Technical Reports Server (NTRS)

Homer, G. David

1991-01-01

The results of dynamic tests using methane and NASA-Z copper test specimen under conditions that simulate those expected in the cooling channels of a regeneratively cooled LOX/hydrocarbon booster engine operating at chamber pressures up to 3000 psi are presented. Methane with less than 0.5 ppm sulfur contamination has little or no effect on cooling channel performance. At higher sulfur concentrations, severe corrosion of the NASA-Z copper alloy occurs and the cuprous sulfide Cu2S, thus formed impedes mass flow rate and heat transfer efficiency. Therefore, it is recommended that the methane specification for this end use set the allowable sulfur content at 0.5 ppm (max). Bulk high purity liquid methane that meets this low sulfur requirement is currently available from only one producer. Pricing, availability, and quality assurance are discussed in detail. Additionally, it was found that dilute sodium cyanide solutions effectively refurbish sulfur corroded cooling channels in only 2 to 5 minutes by completely dissolving all the Cu2S. Sulfur corroded/sodium cyanide refurbished channels are highly roughened and the increased surface roughness leads to significant improvements in heat transfer efficiency with an attendant loss in mass flow rate. Both the sulfur corrosion and refurbishment effects are discussed in detail.

A Thermodynamic Model to Estimate the Formation of Complex Nitrides of Al x Mg(1- x)N in Silicon Steel

NASA Astrophysics Data System (ADS)

Luo, Yan; Zhang, Lifeng; Li, Ming; Sridhar, Seetharaman

2018-06-01

A complex nitride of Al x Mg(1- x)N was observed in silicon steels. A thermodynamic model was developed to predict the ferrite/nitride equilibrium in the Fe-Al-Mg-N alloy system, using published binary solubility products for stoichiometric phases. The model was used to estimate the solubility product of nitride compound, equilibrium ferrite, and nitride compositions, and the amounts of each phase, as a function of steel composition and temperature. In the current model, the molar ratio Al/(Al + Mg) in the complex nitride was great due to the low dissolved magnesium in steel. For a steel containing 0.52 wt pct Als, 10 ppm T.Mg., and 20 ppm T.N. at 1100 K (827 °C), the complex nitride was expressed by Al0.99496Mg0.00504N and the solubility product of this complex nitride was 2.95 × 10-7. In addition, the solution temperature of the complex nitride increased with increasing the nitrogen and aluminum in steel. The good agreement between the prediction and the detected precipitate compositions validated the current model.

Replenishment of fish populations is threatened by ocean acidification

PubMed Central

Munday, Philip L.; Dixson, Danielle L.; McCormick, Mark I.; Meekan, Mark; Ferrari, Maud C. O.; Chivers, Douglas P.

2010-01-01

There is increasing concern that ocean acidification, caused by the uptake of additional CO2 at the ocean surface, could affect the functioning of marine ecosystems; however, the mechanisms by which population declines will occur have not been identified, especially for noncalcifying species such as fishes. Here, we use a combination of laboratory and field-based experiments to show that levels of dissolved CO2 predicted to occur in the ocean this century alter the behavior of larval fish and dramatically decrease their survival during recruitment to adult populations. Altered behavior of larvae was detected at 700 ppm CO2, with many individuals becoming attracted to the smell of predators. At 850 ppm CO2, the ability to sense predators was completely impaired. Larvae exposed to elevated CO2 were more active and exhibited riskier behavior in natural coral-reef habitat. As a result, they had 5–9 times higher mortality from predation than current-day controls, with mortality increasing with CO2 concentration. Our results show that additional CO2 absorbed into the ocean will reduce recruitment success and have far-reaching consequences for the sustainability of fish populations. PMID:20615968

An Ru(II)-Fe(III) bimetallic complex as a multifunctional device for detecting, signal amplifying, and degrading oxalate.

PubMed

Chow, Cheuk-Fai; Ho, Pui-Yu; Gong, Cheng-Bin

2014-09-07

A tetranuclear bimetallic complex, [Ru(II)((t)Bubpy)(CN)4]2-[Fe(III)(H2O)3Cl]2·8H2O (1) has been synthesized and characterized. It was found to be a multifunctional device that can detect, signal amplify, and degrade an organic pollutant, oxalate. Results of the chemosensing studies of 1 toward common anions show that only oxalate selectively induces naked-eye colorimetric and luminometric responses with method detection limits down to 78.7 and 5.5 ppm, respectively from 1. Meanwhile, results of the photo-degradation studies of 1 toward oxalate show that the dissolved organic carbon content of oxalate decreased and reached complete mineralization into CO2 within 6 hours. Complex 1 was also found as the catalyst that amplified the detection signal toward oxalate. Through the photoassisted Fenton reaction by 1, methyl orange, an additional coloring agent, could be degraded so that the visual detection limit of 1 toward oxalate was magnified 50 times from 100 to 2 ppm. The detection, degradation, mineralization and signal amplification were found applicable in real water bodies such as river, pond and underground water with excellent recoveries and relative standard deviation.

Investigation of Gasochromic Rhodium Complexes Towards Their Reactivity to CO and Integration into an Optical Gas Sensor for Fire Gas Detection.

PubMed

Pannek, Carolin; Tarantik, Karina R; Schmitt, Katrin; Wöllenstein, Jürgen

2018-06-21

The detection of the toxic gas carbon monoxide (CO) in the low ppm range is required in different applications. We present a study of the reactivity of different gasochromic rhodium complexes towards the toxic gas carbon monoxide (CO). Therefore, variations of binuclear rhodium complexes with different ligands were prepared. They were characterized by FTIR spectroscopy, ¹H NMR spectroscopy, and differential scanning calorimetry. All complexes are spectroscopically distinguishable and temperature stable up to at least 187 °C. The gasochromic behavior of all different compounds was tested. Therefore, the compounds were dissolved in toluene and exposed to 100 ppm CO for 10 min to investigate their gas sensitivity and reaction velocity. The changes in the transmission spectra were recorded by UV/vis spectroscopy. Furthermore, a significant influence of the solvent to the color dyes’ gasochromic reaction and behavior was observed. After characterization, one complex was transferred as sensing element into an optical gas sensor. Two different measurement principles (reflection- and waveguide-based) were built up and tested towards their capability as gasochromic CO sensors. Finally, different gas-dependent measurements were carried out.

Chlamydomonas angulosa (Green Alga) and Nostoc commune (Blue-Green Alga) Microalgae-Cellulose Composite Aerogel Beads: Manufacture, Physicochemical Characterization, and Cd (II) Adsorption

PubMed Central

Hwang, Kyojung; Kwon, Gu-Joong; Yang, Jiwook; Kim, Minyoung; Hwang, Won Joung; Youe, Wonjae; Kim, Dae-Young

2018-01-01

This study presents composite aerogel beads prepared by mixing dissolved cellulose with Chlamydomonas angulosa and Nostoc commune cells, respectively, at 0.1, 0.3, and 0.5% (w/w). The manufactured composites (termed regenerated cellulose (RC)), with C. angulosa (RCCA-(1, 3, and 5)), and with N. commune (RCNC-(1, 3, and 5)) were analyzed. Both RCCA-5 and RCNC-5 showed the high specific surface area to be about 261.3 and 332.8 m2·g−1. In the microstructure analysis, network structures were observed in the cross-sections of RC, RCCA-5, and RCNC-5. The pyrolysis temperature of the RCCA-5 and RCNC-5 composite aerogel beads was rapidly increased about 250 °C during the mixing of cellulose with C. angulosa and N. commune. The chemical analysis of RC, RCCA-5, and RCNC-5 showed peaks corresponding to various functional groups, such as amide, carboxyl, and hydroxyl groups from protein, lipid, and carbohydrate. RCNC-5 at pH 6 demonstrated highest Cd2+ removal rate about 90.3%, 82.1%, and 63.1% at 10, 25, and 50 ppm Cd2+, respectively. At pH 6, Cd2+ adsorption rates per unit weight of the RCNC-5 were about 0.9025, 2.0514, and 3.1547 mg/g at 10, 25, and 50 ppm, respectively. The peaks assigned to the amide, carboxyl, and hydroxyl groups in RCCA-5, RCNC-5, and RC were shifted or disappeared immediately after adsorption of Cd2+. The specific surface area, total pore volume, and mean pore diameter of composites was decreased due to adsorption of Cd2+ on the developed materials. As can be seen in the X-ray powder diffraction (XRD) spectrum, significant changes in the molecular structure of the composite aerogel beads were not observed even after adsorption of Cd2+. PMID:29621190

Effect of different modified atmospheric packaging (MAP) gaseous combinations on Campylobacter and the shelf-life of chilled poultry fillets.

PubMed

Meredith, H; Valdramidis, V; Rotabakk, B T; Sivertsvik, M; McDowell, D; Bolton, D J

2014-12-01

Studies were undertaken to investigate the effect of different modified atmospheric packaging (MAP) gaseous combinations on Campylobacter and the natural microflora on poultry fillets. Skinless chicken fillets were stored in gaseous mixtures of 10%, 30%, 50%, 70% and 90% CO2 balanced with N2, 80:20% O2:N2 and 40:30:30% CO2:O2:N2 and control conditions (air) at 2 °C. Samples were analysed periodically for (previously inoculated) Campylobacter, total viable counts (TVC) (mesophiles), TVC (psychrophiles), Enterobacteriaceae, Pseudomonas and lactic acid bacteria (LAB) over 17 days of storage. The carbon dioxide solubility was determined by monitoring the changes in the headspace volume over time using a buoyancy technique and performing calculations based on volumetric measurements and the Henry's constant. Henry's constant was also used to estimate the oxygen solubility in the chicken fillets. The presence of O2 in the MAP gaseous mixtures increased the rate of Campylobacter decline on poultry fillets but in general the counts obtained in aerobic versus anaerobic packs were not significantly (P > 0.05) different. CO2 inhibited the growth of TVC, TEC, LAB and Pseudomonas but only at MAP gaseous combinations containing 50-90% CO2 where concentrations of up to 2000 ppm CO2 were recorded in the fillets after 5 days. Under these conditions a shelf-life in excess of 17 days at 2 °C was obtained. Although, dissolved O2, at levels of 33 ppm in 80:20% O2:N2 packs after 3 days, reduced Campylobacter, it also favoured the growth of the other microbes on the chicken. The optimum gaseous mixture for achieving the combined objectives of reducing Campylobacter and extending shelf was therefore 40:30:30 CO2:O2:N2, which achieved a shelf-life in excess of 14 days. Copyright © 2014 Elsevier Ltd. All rights reserved.

Molecular Signature of Organic Carbon Along a Salinity Gradient in Suwannee River Plume

NASA Astrophysics Data System (ADS)

Liu, Y.; Bianchi, T. S.; Ward, N. D.; Arellano, A. R.; Paša-Tolić, L.; Tolic, N.; Kuo, L. J.

2016-12-01

Humic and fulvic acid isolates from Suwannee River dissolved organic matter (DOM) have served as reference standards for the International Humic Substances Society (IHSS) for many decades. The large database on Suwannee DOM provides an excellent framework to further expand the application of Fourier transform ion cyclotron mass spectrometry (FT-ICR-MS) in characterizing the chemical composition of aquatic DOM. In this study, we examined the DOM signature of the lower Suwannee River and plume region at 5 stations along a salinity gradient (0 to 28) using FT-ICR-MS. The chemical characteristics of DOM show distinct differences across this steep salinity gradient. In general, samples collected from the coastal station have lower carbon number and are less aromatic. Molecular level analysis reveals that the magnitude weighted proportion of lipids increased as salinity increased. Interestingly, a similar trend was observed for lignin-like compounds. Target quantification of lignin-phenols showed that while the concentrations of these compounds were lower at the coastal station, the DOC-normalized concentrations were not significantly different between the river and coastal stations. In addition to traditional DOM moieties, we identified for the first time, halogenated organic compounds (HOC). We observed more chlorinated compounds in DOM and increased Cl/C as salinity increased. A relatively high proportion of halogenated lipids (compared to non-halogenated) were observed in the total pool of HOC across all stations. Although not significant in relative proportion, halogenated lignin-like compounds were the most abundant HOC moieties in our samples. CO2 concentrations decreased and became more 13C-enriched along the salinity gradient, ranging from 3,990 ppm (13CO2 = -17.3‰) at salinity 0 to 520 ppm (13CO2 = -7.5‰) at salinity 28, indicating high levels of DOM degradation in the river and a shift to primary production in the marine receiving waters, which is consistent with trends of lipid and lignin-like compounds observed with FT-ICR-MS.

The negative effect of environmental geological conditions of some geo-archaeological sites of North Coast and Alexandria

NASA Astrophysics Data System (ADS)

Ibrahim, Hani; Kamh, Gamal

2005-12-01

Three geo-archaeological sites at the North Coast and Alexandria, namely, the Alexandria wall (El Shalalat Park site), Abu Soir temple, and Marina excavations, were investigated to determine the negative impact of a salty environmental condition. The monuments suffer from rock decay of different rates. The geo-archaeological sites were built mainly from oolitic limestone blocks (i.e., the Alexandria wall at the El Shalalat Park site and Abu Soir temple) or excavated on them (i.e., Marina excavations). Field inspection and a lab analysis were carried out to understand the weathering mechanism. Salt weathering criteria such as disintegration, pitting, scaling, exfoliation, and honeycomb are observed on the Alexandria wall and upper parts of the Abu Soir temple, while dangerous cracks are detected on the Marina excavation tombs. The petrographic study of the oolitic limestone samples shows that they consist mainly of oolities and drusy sparite as a cement (oolitic grainstone). Some oolities have quartz grains as nuclei. Hydrochemical analysis shows that the total dissolved salts of extracted solutions of the North Coast quarry samples range from 539 to 686 ppm and dramatically increase (i.e., ten times) for extracted solutions from monument samples, ranging from 5395 to 6880 ppm. The dominant cation is sodium while the dominant anion is chlorine. Acid insoluble residue analysis shows that the carbonate content ranges from 89.2% to 96.4% for fresh samples from quarries and from 9.2% to 94.8% for weathered monument samples. The weight loss of the quarry oolitic limestone samples range from 30.7% to 32.7% and its physical and mechanical properties become worse after being subjected to 15 cycles of a durability simulation soundness test (using a sodium sulphate solution). Our main recommendations are to use suitable grouting for binding the cracks, high durability reconstruction rocks, and suitable cleaning methods to remove salts from the monuments.

Post-Late Glacial calcareous tufas from the Kurai fault zone (Southeastern Gorny Altai, Russia)

NASA Astrophysics Data System (ADS)

Kokh, Svetlana N.; Sokol, Ella V.; Deev, Evgeny V.; Ryapolova, Yuliya M.; Rusanov, Gennady G.; Tomilenko, Anatoliy A.; Bul'bak, Taras A.

2017-06-01

Calcareous tufa deposits have been discovered in the Chibitka River valley near Lake Cheybek-Kohl, at the junction of the Kurai and Teletsk-Kurai large active faults in the southeastern Gorny Altai, Russia, at an altitude of 1800-2000 m. Fossil tufa is composed of calcite and cements Holocene grey colluvium and glacial till deposited by the Late Glacial Chibitka Glacier. Current tufa precipitation has been observed from a low-flow spring with cold (10 °C) HCO3-SO4-Ca-Mg water, pH = 6.86. The stable isotope composition of spring water is - 5.8‰ VPDB δ13C of dissolved inorganic carbon and - 14.5‰ VSMOW δ18O. Modern tufa consists of thin laminated Mg-calcite and Sr-aragonite crusts, with abundant algae and biofilms on their surfaces. Both modern and fossil tufas are depleted in REE (a total of 0.40-16.4 ppm and 0.40-3.80 ppm, respectively) and share similar PAAS-normalised REE + Y spectra with HREE enrichment and slight progressive LREE depletion. The modern tufas show positive δ13C values of 0.1‰ to 0.9‰ VPDB while the fossil ones have an isotopically lighter composition of δ13C = - 4.1‰ to - 1.9‰ VPDB; the δ18O range is very narrow (- 13.0 to - 13.8‰ VPDB). Both stable isotope and trace-element signatures (including REE patterns) of the tufas indicate precipitation from cold groundwaters subjected to prolonged interaction with a carbonate aquifer (the Baratal Group of limestone and dolostone) in a cold continental climate similar to the present conditions. Tufa deposition in the Lake Cheybek-Kohl area began with the onset of post-Late Glacial global warming and permafrost degradation. Unlike the fossil tufa formation, current precipitation of freshwater carbonates has been microbially mediated. The discovered tufa deposits provide new palaeoclimatic and active tectonic proxies in the southeastern Gorny Altai.

Selected papers in the hydrologic sciences, 1986

USGS Publications Warehouse

Subitzky, Seymour

1987-01-01

Water-quality data from long-term (24 years), fixed- station monitoring at the Cape Fear River at Lock 1 near Kelly, N.C., and various measures of basin development are correlated. Subbasin population, number of acres of cropland in the subbasin, number of people employed in manufacturing, and tons of fertilizer applied in the basin are considered as measures of basinwide development activity. Linear correlations show statistically significant posi- tive relations between both population and manufacturing activity and most of the dissolved constituents considered. Negative correlations were found between the acres of harvested cropland and most of the water-quality measures. The amount of fertilizer sold in the subbasin was not statistically related to the water-quality measures considered in this report. The statistical analysis was limited to several commonly used measures of water quality including specific conductance, pH, dissolved solids, several major dissolved ions, and a few nutrients. The major dissolved ions included in the analysis were calcium, sodium, potassium, magnesium, chloride, sulfate, silica, bicarbonate, and fluoride. The nutrients included were dissolved nitrite plus nitrate nitrogen, dissolved ammonia nitrogen, total nitrogen, dissolved phosphates, and total phosphorus. For the chemicals evaluated, manufacturing and population sources are more closely associated with water quality in the Cape Fear River at Lock 1 than are agricultural variables.

Ground-water resources of Monmouth County, New Jersey

USGS Publications Warehouse

Jablonski, Leo A.

1968-01-01

Aquifers in the Raritan and Magothy Formations and the Englishtown Formation supplied 76 percent of the ground water used in 1958. These aquifers, in conjunction with the Wenonah Formation and Mount Laurel Sand of Late Cretaceous age, are capable of providing relatively large yields to wells. The average yield of 63 large-diameter wells tapping these aquifers is 580 gpm, at depths randing from 100 to 1,140 feet. In general, the concentrations of chemical constituents in water from the aquifers would not restrict the use of the water for most purposes. High concentrations of iron do occur and require treatment. The concentrations of dissolved solids in 39 to 41 samples were 160 ppm (parts per million) or less.

The Paradox of a Wet (High H2O) and Dry (Low H2O/Ce) Mantle: High Water Concentrations in Mantle Garnet Pyroxenites from Hawaii

NASA Technical Reports Server (NTRS)

Peslier, Anne H.; Bizimis, Michael

2013-01-01

Water dissolved as trace amounts in anhydrous minerals has a large influence on the melting behavior and physical properties of the mantle. The water concentration of the oceanic mantle is inferred from the analyses of Mid-Ocean Ridge Basalt (MORB) and Oceanic Island Basalt (OIB). but there is little data from actual mantle samples. Moreover, enriched mineralogies (pyroxenites, eclogites) are thought as important sources of heterogeneity in the mantle, but their water concentrations and their effect on the water budget and cycling in the mantle are virtually unknown. Here, we analyzed by FTIR water in garnet clinopyroxenite xenoliths from Salt Lake Crater, Oahu, Hawaii. These pyroxenites are high-pressure (>20kb) crystal fractionates from alkalic melts. The clinopyroxenes (cpx) have 260 to 576 ppm wt H2O, with the least differentiated samples (Mg#>0.8) in the 400-500 ppm range. Orthopyroxene (opx) contain 117-265 ppm H2O, about half of that of cpx, consistent with other natural sample studies, but lower than cpx/opx equilibrium from experimental data. The pyroxenite cpx and opx H2O concentrations are at the high-end of on-and off-craton peridotite xenolith concentrations and those of Hawaiian spinel peridotites. In contrast, garnet has extremely low water contents (<5ppm H2O). There is no correlation between H2O in cpx and lithophile element concentrations. Phlogopite is present in some samples, and its modal abundance shows a positive correlation in Mg# with cpx, implying equilibrium. However, there is no correlation between H2O concentrations and or the presence of phlogopite. These data imply that cpx and opx may be at water saturation, far lower than experimental data suggest. Reconstructed bulk rock pyroxenite H2O ranges from 200-460 ppm (average 331 +/- 75 ppm), 2 to 8 times higher than H2O estimates for the MORB source (50-200 ppm), but in the range of E-MORB, OIB and the source of rejuvenated Hawaiian magmas. The average bulk rock pyroxenite H2O/Ce is 69 +/-35, lower than estimates of the MORB source (approx 150) or FOZO, C (200-250) mantle component, but consistent with "dry" EM sources (<100). These data suggest that a metasomatized, refertilized oceanic lithosphere that contains pyroxenitic veins (e.g. the lower part of an oceanic plate, where ascending melts can become trapped and crystallize), will have both higher water concentrations and low H2O/Ce, and may contribute to EM-type OIB sources, like that of Samoa basalts. Therefore, a low H2O/Ce mantle source may not necessarily be "dry".

Undegassed Carbon Content from a Highly Depleted Segment of the Mid-Atlantic Ridge (1-5°S): Evidence from Melt Inclusions

NASA Astrophysics Data System (ADS)

Le Voyer, M.; Kelley, K. A.; Cottrell, E.; Hauri, E. H.

2014-12-01

As carbon solubility is low in basalts, MORB contain little dissolved CO2 (189±61 ppm, 1σ, n=600 [1]). A global negative correlation between CO2/Nb (proxy for amount of CO2 lost by degassing) and Ba/La (proxy for source enrichment) indicates that depleted MORB are less affected by degassing than enriched MORB: CO2/Nb ratios range from 0-100 for samples with Ba/La>4, while CO2/Nb range from 50 to 400 for samples with Ba/La<4 [1]. To assess the CO2 content of undegassed MORB, we analyzed the volatile content of 70 olivine-hosted, glassy melt inclusions (MIs) from four basalts dredged along MAR 1-5°S, a ridge segment that produces highly depleted MORB in terms of trace element enrichment and radiogenic isotopes [2, 3]. MIs contain CO2 contents (180-1420 ppm) that are higher than their respective matrix glasses (130-220 ppm, typical for vapor-saturated melts erupted at 3-5 km b.s.l.). One of the four dredges (EN061 5D-3Ag) contains MIs that do not exhibit shrinkage bubbles. For this sample only, we find a positive correlation between the CO2 content (240-770 ppm) and the Cl content (6-20 ppm) of the MIs that is not found in the matrix glasses (see Fig.). We infer that the correlation between CO2 and Cl, both highly incompatible in silicate minerals during fractional crystallization, is strong evidence for vapor-undersaturation, as any CO2 degassing would have erased the correlation. Together with MIs from the Siqueiros Fracture Zone [4] and from northern Iceland [5], the MIs from EN061 5D-3Ag may represent another occurrence of carbon-undersaturated MORB. Our results will be used to model the primary carbon content of MORB and of the depleted upper mantle. Note that the average Cl content of the matrix glasses (20±1 ppm) is higher than those of the MIs (12±3 ppm, see Fig.). This indicates either that the matrix glasses assimilated a small amount of seawater Cl, or that the MIs are all more depleted than the matrix glass. We will acquire major and trace element data in order to further investigate the origin of the low Cl and high CO2 contents in these MIs. Ref. [1] Le Voyer et al. 2014 Goldschmidt abstr. [2] Schilling et al. 1994 JGR 99 [3] Kelley et al. 2013 G3 [4] Saal et al. 2002 Nature 419 [5] Hauri and Saal 2009 EOS Fall suppl. AGU abstr.

Nutrient concentrations in Upper and Lower Echo, Fallen Leaf, Spooner, and Marlette Lakes and associated outlet streams, California and Nevada, 2002-03

USGS Publications Warehouse

Lico, Michael S.

2004-01-01

Five lakes and their outlet streams in the Lake Tahoe Basin were sampled for nutrients during 2002-03. The lakes and streams sampled included Upper Echo, Lower Echo, Fallen Leaf, Spooner, and Marlette Lakes and Echo, Taylor, and Marlette Creeks. Water samples were collected to determine seasonal and spatial concentrations of dissolved nitrite plus nitrate, dissolved ammonia, total Kjeldahl nitrogen, dissolved orthophosphate, total phosphorus, and total bioreactive iron. These data will be used by Tahoe Regional Planning Agency in revising threshold values for waters within the Lake Tahoe Basin. Standard U.S. Geological Survey methods of sample collection and analysis were used and are detailed herein. Data collected during this study and summary statistics are presented in graphical and tabular form.

Summary of surface-water-quality data collected for the Northern Rockies Intermontane Basins National Water-Quality Assessment Program in the Clark Fork-Pend Oreille and Spokane River basins, Montana, Idaho, and Washington, water years 1999-2001

USGS Publications Warehouse

Beckwith, Michael A.

2003-01-01

Water-quality samples were collected at 10 sites in the Clark Fork-Pend Oreille and Spokane River Basins in water years 1999 – 2001 as part of the Northern Rockies Intermontane Basins (NROK) National Water-Quality Assessment (NAWQA) Program. Sampling sites were located in varied environments ranging from small streams and rivers in forested, mountainous headwater areas to large rivers draining diverse landscapes. Two sampling sites were located immediately downstream from the large lakes; five sites were located downstream from large-scale historical mining and oreprocessing areas, which are now the two largest “Superfund” (environmental remediation) sites in the Nation. Samples were collected during a wide range of streamflow conditions, more frequently during increasing and high streamflow and less frequently during receding and base-flow conditions. Sample analyses emphasized major ions, nutrients, and selected trace elements. Streamflow during the study ranged from more than 130 percent of the long-term average in 1999 at some sites to 40 percent of the long-term average in 2001. River and stream water in the study area exhibited small values for specific conductance, hardness, alkalinity, and dissolved solids. Dissolved oxygen concentrations in almost all samples were near saturation. Median total nitrogen and total phosphorus concentrations in samples from most sites were smaller than median concentrations reported for many national programs and other NAWQA Program study areas. The only exceptions were two sites downstream from large wastewater-treatment facilities, where median concentrations of total nitrogen exceeded the national median. Maximum concentrations of total phosphorus in samples from six sites exceeded the 0.1 milligram per liter threshold recommended for limiting nuisance aquatic growth. Concentrations of arsenic, cadmium, copper, lead, mercury, and zinc were largest in samples from sites downstream from historical mining and ore-processing areas in the upper Clark Fork in Montana and the South Fork Coeur d’Alene River in Idaho. Concentrations of dissolved lead in all 32 samples from the South Fork Coeur d’Alene River exceeded the Idaho chronic criterion for the protection of aquatic life at the median hardness level measured during the study. Concentrations of dissolved zinc in all samples collected at this site exceeded both the chronic and acute criteria at all hardness levels measured. When all data from all NROK sites were combined, median concentrations of dissolved arsenic, dissolved and total recoverable copper, total recoverable lead, and total recoverable zinc in the NROK study area appeared to be similar to or slightly smaller than median concentrations at sites in other NAWQA Program study areas in the Western United States affected by historical mining activities. Although the NROK median total recoverable lead concentration was the smallest among the three Western study areas compared, concentrations in several NROK samples were an order of magnitude larger than the maximum concentrations measured in the Upper Colorado River and Great Salt Lake Basins. Dissolved cadmium, dissolved lead, and total recoverable zinc concentrations at NROK sites were more variable than in the other study areas; concentrations ranged over almost three orders of magnitude between minimum and maximum values; the range of dissolved zinc concentrations in the NROK study area exceeded three orders of magnitude.

Examination of the Effects of Arsenic on Glucose Homeostasis in Cell Culture and Animal Studies: Development of a Mouse Model for Arsenic-Induced Diabetes

PubMed Central

Paul, David S.; Hernández-Zavala, Araceli; Walton, Felecia S.; Adair, Blakely M.; dina, Jiří D; Matoušek, Tomáš; Stýblo, Miroslav

2009-01-01

Previous epidemiologic studies found increased prevalences of type 2 diabetes mellitus in populations exposed to high levels of inorganic arsenic (iAs) in drinking water. Although results of epidemiologic studies in low-exposure areas or occupational settings have been inconclusive, laboratory research has shown that exposures to iAs can produce effects that are consistent with type 2 diabetes. The current paper reviews the results of laboratory studies that examined the effects of iAs on glucose metabolism and describes new experiments in which the diabetogenic effects of iAs exposure were reproduced in a mouse model. Here, weanling male C57BL/6 mice drank deionized water with or without the addition of arsenite (25 or 50 ppm As) for 8 weeks. Intraperitoneal glucose tolerance tests revealed impaired glucose tolerance in mice exposed to 50 ppm As, but not to 25 ppm As. Exposure to 25 and 50 ppm As in drinking-water resulted in proportional increases in the concentration of iAs and its metabolites in the liver and in organs targeted by type 2 diabetes, including pancreas, skeletal muscle and adipose tissue. Dimethylarsenic was the predominant form of As in the tissues of mice in both 25 and 50 ppm groups. Notably, the average concentration of total speciated arsenic in livers from mice in the 50 ppm group was comparable to the highest concentration of total arsenic reported in the livers of Bangladeshi residents who had consumed water with an order of magnitude lower level of iAs. These data suggest that mice are less susceptible than humans to the diabetogenic effects of chronic exposure to iAs due to a more efficient clearance of iAs or its metabolites from target tissues. PMID:17336358

Out of the dark: transitional subsurface-to-surface microbial diversity in a terrestrial serpentinizing seep (Manleluag, Pangasinan, the Philippines)

PubMed Central

Woycheese, Kristin M.; Meyer-Dombard, D'Arcy R.; Cardace, Dawn; Argayosa, Anacleto M.; Arcilla, Carlo A.

2015-01-01

In the Zambales ophiolite range, terrestrial serpentinizing fluid seeps host diverse microbial assemblages. The fluids fall within the profile of Ca2+-OH−-type waters, indicative of active serpentinization, and are low in dissolved inorganic carbon (DIC) (<0.5 ppm). Influx of atmospheric carbon dioxide (CO2) affects the solubility of calcium carbonate as distance from the source increases, triggering the formation of meter-scale travertine terraces. Samples were collected at the source and along the outflow channel to determine subsurface microbial community response to surface exposure. DNA was extracted and submitted for high-throughput 16S rRNA gene sequencing on the Illumina MiSeq platform. Taxonomic assignment of the sequence data indicates that 8.1% of the total sequence reads at the source of the seep affiliate with the genus Methanobacterium. Other major classes detected at the source include anaerobic taxa such as Bacteroidetes (40.7% of total sequence reads) and Firmicutes (19.1% of total reads). Hydrogenophaga spp. increase in relative abundance as redox potential increases. At the carbonate terrace, 45% of sequence reads affiliate with Meiothermus spp. Taxonomic observations and geochemical data suggest that several putative metabolisms may be favorable, including hydrogen oxidation, H2-associated sulfur cycling, methanogenesis, methanotrophy, nitrogen fixation, ammonia oxidation, denitrification, nitrate respiration, methylotrophy, carbon monoxide respiration, and ferrous iron oxidation, based on capabilities of nearest known neighbors. Scanning electron microscopy and energy dispersive X-ray spectroscopy suggest that microbial activity produces chemical and physical traces in the precipitated carbonates forming downstream of the seep's source. These data provide context for future serpentinizing seep ecosystem studies, particularly with regards to tropical biomes. PMID:25745416

Out of the dark: transitional subsurface-to-surface microbial diversity in a terrestrial serpentinizing seep (Manleluag, Pangasinan, the Philippines).

PubMed

Woycheese, Kristin M; Meyer-Dombard, D'Arcy R; Cardace, Dawn; Argayosa, Anacleto M; Arcilla, Carlo A

2015-01-01

In the Zambales ophiolite range, terrestrial serpentinizing fluid seeps host diverse microbial assemblages. The fluids fall within the profile of Ca(2+)-OH(-)-type waters, indicative of active serpentinization, and are low in dissolved inorganic carbon (DIC) (<0.5 ppm). Influx of atmospheric carbon dioxide (CO2) affects the solubility of calcium carbonate as distance from the source increases, triggering the formation of meter-scale travertine terraces. Samples were collected at the source and along the outflow channel to determine subsurface microbial community response to surface exposure. DNA was extracted and submitted for high-throughput 16S rRNA gene sequencing on the Illumina MiSeq platform. Taxonomic assignment of the sequence data indicates that 8.1% of the total sequence reads at the source of the seep affiliate with the genus Methanobacterium. Other major classes detected at the source include anaerobic taxa such as Bacteroidetes (40.7% of total sequence reads) and Firmicutes (19.1% of total reads). Hydrogenophaga spp. increase in relative abundance as redox potential increases. At the carbonate terrace, 45% of sequence reads affiliate with Meiothermus spp. Taxonomic observations and geochemical data suggest that several putative metabolisms may be favorable, including hydrogen oxidation, H2-associated sulfur cycling, methanogenesis, methanotrophy, nitrogen fixation, ammonia oxidation, denitrification, nitrate respiration, methylotrophy, carbon monoxide respiration, and ferrous iron oxidation, based on capabilities of nearest known neighbors. Scanning electron microscopy and energy dispersive X-ray spectroscopy suggest that microbial activity produces chemical and physical traces in the precipitated carbonates forming downstream of the seep's source. These data provide context for future serpentinizing seep ecosystem studies, particularly with regards to tropical biomes.

The Effect of Oxygen Supply on the Dual Growth Kinetics of Acidithiobacillus thiooxidans under Acidic Conditions for Biogas Desulfurization

PubMed Central

Namgung, Hyeong-Kyu; Song, JiHyeon

2015-01-01

In this study, to simulate a biogas desulfurization process, a modified Monod-Gompertz kinetic model incorporating a dissolved oxygen (DO) effect was proposed for a sulfur-oxidizing bacterial (SOB) strain, Acidithiobacillus thiooxidans, under extremely acidic conditions of pH 2. The kinetic model was calibrated and validated using experimental data obtained from a bubble-column bioreactor. The SOB strain was effective for H2S degradation, but the H2S removal efficiency dropped rapidly at DO concentrations less than 2.0 mg/L. A low H2S loading was effectively treated with oxygen supplied in a range of 2%–6%, but a H2S guideline of 10 ppm could not be met, even with an oxygen supply greater than 6%, when the H2S loading was high at a short gas retention time of 1 min and a H2S inlet concentration of 5000 ppm. The oxygen supply should be increased in the aerobic desulfurization to meet the H2S guideline; however, the excess oxygen above the optimum was not effective because of the decline in oxygen efficiency. The model estimation indicated that the maximum H2S removal rate was approximately 400 ppm/%-O2 at the influent oxygen concentration of 4.9% under the given condition. The kinetic model with a low DO threshold for the interacting substrates was a useful tool to simulate the effect of the oxygen supply on the H2S removal and to determine the optimal oxygen concentration. PMID:25633028

Assessing variability and trends in Arctic sea ice distribution using satellite data

USGS Publications Warehouse

Belchansky, G.I.; Mordvintsev, Ilia N.; Douglas, David C.

1996-01-01

A survey of organochlorine residues in woodcock wings was undertaken to determine whether these wings are suitable for showing regional differences in residues and to obtain a baseline in 1970-71 for later comparisons. Woodcock wings were obtained from the annual hunter's wing survey. Samples came from eight States (Louisiana, Maine, Michigan, New Hampshire, New Jersey, New York, Pennsylvania, and Wisconsin) and one tri-State area (North Carolina, South Carolina, and Georgia). Wings from the tri-State area contained significantly higher (P<0.01) concentrations of DDT (including DDT, DDD, and DDE) than those from other States. Concentrations of polychlorinated biphenyls (PCB's) also were significantly higher (P<0.05) in samples from these three States. Wings from Louisiana and the tri-State area had significantly higher (P<0.01) concentrations of dieldrin than wings from the other States, and those from Louisiana had significantly higher (P < 0.01) concentrations of mirex than those from other States. (Residues are on lipid base) The compounds detected and the ranges of residue means for all sampling areas were as follows: Total DDT (5.89--65.15 ppm); DDT (0.34 m--14.93 ppm); DDE (4.66--47.47 ppm); DDD (0.11--3.44 ppm); mirex (0.76--16.93 ppm); dieldrin (0.09--3.06 ppm); and PCB's (4.27--8.63 ppm). Woodcock wings appear to be suitable for determining regional differences in organochlorine residues in this species.

Good medicine for conservation biology: The intersection of epidemiology and conservation theory

USGS Publications Warehouse

Lafferty, Kevin D.; Gerber, Leah R.

2002-01-01

A survey of organochlorine residues in woodcock wings was undertaken to determine whether these wings are suitable for showing regional differences in residues and to obtain a baseline in 1970-71 for later comparisons. Woodcock wings were obtained from the annual hunter's wing survey. Samples came from eight States (Louisiana, Maine, Michigan, New Hampshire, New Jersey, New York, Pennsylvania, and Wisconsin) and one tri-State area (North Carolina, South Carolina, and Georgia). Wings from the tri-State area contained significantly higher (P<0.01) concentrations of DDT (including DDT, DDD, and DDE) than those from other States. Concentrations of polychlorinated biphenyls (PCB's) also were significantly higher (P<0.05) in samples from these three States. Wings from Louisiana and the tri-State area had significantly higher (P<0.01) concentrations of dieldrin than wings from the other States, and those from Louisiana had significantly higher (P < 0.01) concentrations of mirex than those from other States. (Residues are on lipid base) The compounds detected and the ranges of residue means for all sampling areas were as follows: Total DDT (5.89--65.15 ppm); DDT (0.34 m--14.93 ppm); DDE (4.66--47.47 ppm); DDD (0.11--3.44 ppm); mirex (0.76--16.93 ppm); dieldrin (0.09--3.06 ppm); and PCB's (4.27--8.63 ppm). Woodcock wings appear to be suitable for determining regional differences in organochlorine residues in this species.

Air quality at night markets in Taiwan.

PubMed

Zhao, Ping; Lin, Chi-Chi

2010-03-01

In Taiwan, there are more than 300 night markets and they have attracted more and more visitors in recent years. Air quality in night markets has become a public concern. To characterize the current air quality in night markets, four major night markets in Kaohsiung were selected for this study. The results of this study showed that the mean carbon dioxide (CO2) concentrations at fixed and moving sites in night markets ranged from 326 to 427 parts per million (ppm) during non-open hours and from 433 to 916 ppm during open hours. The average carbon monoxide (CO) concentrations at fixed and moving sites in night markets ranged from 0.2 to 2.8 ppm during non-open hours and from 2.1 to 14.1 ppm during open hours. The average 1-hr levels of particulate matter with aerodynamic diameters less than 10 microm (PM10) and less than 2.5 microm (PM2.5) at fixed and moving sites in night markets were high, ranging from 186 to 451 microg/m3 and from 175 to 418 microg/m3, respectively. The levels of PM2.5 accounted for 80-97% of their respective PM10 concentrations. The average formaldehyde (HCHO) concentrations at fixed and moving sites in night markets ranged from 0 to 0.05 ppm during non-open hours and from 0.02 to 0.27 ppm during open hours. The average concentration of individual polycyclic aromatic hydrocarbons (PAHs) was found in the range of 0.09 x 10(4) to 1.8 x 10(4) ng/m3. The total identified PAHs (TIPs) ranged from 7.8 x 10(1) to 20 x 10(1) ng/m3 during non-open hours and from 1.5 x 10(4) to 4.0 x 10(4) ng/m3 during open hours. Of the total analyzed PAHs, the low-molecular-weight PAHs (two to three rings) were the dominant species, corresponding to an average of 97% during non-open hours and 88% during open hours, whereas high-molecular-weight PAHs (four to six rings) represented 3 and 12% of the total detected PAHs in the gas phase during non-open and open hours, respectively.

Experimental investigation of oily wastewater treatment using combined membrane systems.

PubMed

Salahi, A; Mohammadi, T

2010-01-01

Investigations were carried out for purification of oily wastewater by a combined of ultrafiltration/reverse osmosis (UF/RO) processes. Laboratory-scale UF using polysulfone (PS) and polyacrylonitrile (PAN) membranes were employed with typical oily wastewater collected from API unit of Tehran refinery. The PAN membrane showed higher rejection, more permeation flux and less fouling resistance than the PS membrane. Both membranes produced permeate with oil and grease contents generally less than 5 ppm. Rejection of chemical oxygen demand (COD) and biological oxygen demand (BOD5) were found to be 65% for UF treatment. In this work, Hermia's models were used to investigate the fouling mechanism involved in UF of the oily wastewater. The results showed that the best fit to experimental data corresponds to the cake layer formation model followed by the intermediate blocking model for both the UF membranes. For further treatment of the UF permeates, RO was applied using a thin film composite polyamide membrane. The rejection of COD, BOD5 and total dissolved solid (TDS) after UF/RO treatment increased up to 98%, 98% and 95%, respectively. The results showed that the final permeate has very high quality and even better than that is currently introduced to the cooling towers in Tehran refinery.

A Thin Film Nanocomposite Membrane with MCM-41 Silica Nanoparticles for Brackish Water Purification.

PubMed

Kadhom, Mohammed; Yin, Jun; Deng, Baolin

2016-12-06

Thin film nanocomposite (TFN) membranes containing MCM-41 silica nanoparticles (NPs) were synthesized by the interfacial polymerization (IP) process. An m -phenylenediamine (MPD) aqueous solution and an organic phase with trimesoyl chloride (TMC) dissolved in isooctane were used in the IP reaction, occurring on a nanoporous polysulfone (PSU) support layer. Isooctane was introduced as the organic solvent for TMC in this work due to its intermediate boiling point. MCM-41 silica NPs were loaded in MPD and TMC solutions in separate experiments, in a concentration range from 0 to 0.04 wt %, and the membrane performance was assessed and compared based on salt rejection and water flux. The prepared membranes were characterized via scanning electron microscopy (SEM), transmission electron microscopy (TEM), contact angle measurement, and attenuated total reflection Fourier transform infrared (ATR FT-IR) analysis. The results show that adding MCM-41 silica NPs into an MPD solution yields slightly improved and more stable results than adding them to a TMC solution. With 0.02% MCM-41 silica NPs in the MPD solution, the water flux was increased from 44.0 to 64.1 L/m²·h, while the rejection virtually remained the same at 95% (2000 ppm NaCl saline solution, 25 °C, 2068 kPa (300 psi)).

Effect of physico-chemical treatments on ripening behavior and post-harvest quality of Amrapali mango (Mangifera indica L.) during storage.

PubMed

Singh, Pankaj; Singh, Manoj Kumar; Kumar, Vipin; Kumar, Mukesh; Malik, Sunil

2012-03-01

An experiment was done to assess the effect of various physico-chemical treatments on ripening behavior and post harvest quality of mango cv. Amrapali. The experiment was planned under completely randomized design (CRD) with three replications. The treatment units was five fruits per replication. Total 14 treatments were applied. Out of these, ethrel 750 ppm treated fruits showed better results in respect of specific gravity (0.88), moisture loss (8.45%), decay (2.5%), total soluble solids (TSS, 20.7 degrees brix), sugar content (14.39%) and acidity content (0.32) followed by ethrel 500 ppm; specific gravity (0.90), moisture loss (8.82%), decay (3.5%), TSS (20.7 degrees brix), sugar content (13.99%) and acidity content (0.36%). The pedicellate fruits and ethrel+bavistin (750+1000 ppm) were also found to be significantly superior over control in respect of specific gravity (0.88 and 0.86), moisture loss (9.10 and 9.33%), decay (4.0 and 5.33%), TSS (20.1 and 20.4 degrees brix), sugar content (12.70 and 12.80%) and acidity content (0.42 and 0.38%), respectively. Based on results of this study, it can be concluded that ethrel 750 ppm was found to be the most suitable treatment in improving physico-chemical traits i.e. ripening, storage, quality and shelf-life for commercial purpose in mango.

¹H MRS characterization of neurochemical profiles in orthotopic mouse models of human brain tumors.

PubMed

Hulsey, Keith M; Mashimo, Tomoyuki; Banerjee, Abhishek; Soesbe, Todd C; Spence, Jeffrey S; Vemireddy, Vamsidhara; Maher, Elizabeth A; Bachoo, Robert M; Choi, Changho

2015-01-01

Glioblastoma (GBM), the most common primary brain tumor, is resistant to currently available treatments. The development of mouse models of human GBM has provided a tool for studying mechanisms involved in tumor initiation and growth as well as a platform for preclinical investigation of new drugs. In this study we used (1) H MR spectroscopy to study the neurochemical profile of a human orthotopic tumor (HOT) mouse model of human GBM. The goal of this study was to evaluate differences in metabolite concentrations in the GBM HOT mice when compared with normal mouse brain in order to determine if MRS could reliably differentiate tumor from normal brain. A TE =19 ms PRESS sequence at 9.4 T was used for measuring metabolite levels in 12 GBM mice and 8 healthy mice. Levels for 12 metabolites and for lipids/macromolecules at 0.9 ppm and at 1.3 ppm were reliably detected in all mouse spectra. The tumors had significantly lower concentrations of total creatine, GABA, glutamate, total N-acetylaspartate, aspartate, lipids/macromolecules at 0.9 ppm, and lipids/macromolecules at 1.3 ppm than did the brains of normal mice. The concentrations of glycine and lactate, however, were significantly higher in tumors than in normal brain. Copyright © 2014 John Wiley & Sons, Ltd.

Geology and hydrology of the West Milton area, Saratoga County, New York

USGS Publications Warehouse

Mack, Frederick K.; Pauszek, F.H.; Crippen, John R.

1964-01-01

This report describes the geology, ground-water conditions, streamflow characteristics, and quality of water in the West Milton area, Saratoga County, N.Y. The West Milton area is in the east-central part of New York in the hilly region that forms a transition zone between the Adirondack Mountains and the Hudson-Mohawk valley lowland. Bedrock underlying the area consists of crystalline rocks of Precambrian age and sandstone, dolomite, limestone, and shale formations of Cambrian and Ordovician age. The formations have been moderately folded and have been displaced as much as several hundred feet' along at least three northeast-trending normal faults. The bedrock is overlain in nearly all parts of the area by a layer of unconsolidated deposits which ranges in thickness from a few feet to more than 200 feet. The unconsolidated deposits are of Pleistocene age and consist of unstratified materials (till) laid down by glacial ice at stratified sediments deposited by glacial meltwaters. The topography of the bedrock surface differs greatly from the topography of the land surface. Although not evident in the present topography, at least two channels, cut in bedrock by preglacial streams, pass through the area. Ground-water supplies adequate to satisfy domestic requirements can be obtained from wells in any part of the area. Large ground-water supplies may be taken from coarse-grained stratified deposits comprising two aquifers in the valley of Kayaderosseras Creek. The Atomic Energy Commission has pumped as much as 1 mgd from a horizontal well drawing from the uppermost aquifer which is composed of flood-plain deposits. Part of the water yielded by this well during extended periods of pumping is induced flow from the creek. Three nearby vertical wells drilled by the Commission comprise a separate well field capable of yielding at least 2 mgd and possibly as much as 3 mgd from the deeper stratified deposits underlying the valley. A pumping test showed that at near the center of this well field the coefficient of transmissibility is about 125,000 gpd per ft and the coefficient of storage is about 0.0003. The water obtained from the sand and gravel has a hardness of about 125 ppm and contains about 150 ppm of dissolved solids. Most of the Government reservation is drained by Glowegee Creek, one of the larger tributaries of Kayaderosseras Creek. The average streamflow of Kayaderosseras Creek at West Milton is 141 cfs or about 1.5 cfs per sq. mi. The monthly mean discharge has ranged from a low of 21.7 cfs in September 1958 to a high of 866 cfs in March 1936, and the annual mean discharge has ranged from 94.5 cfs in 1941 to 198 cfs in 1952. The mean annual flood is 1,740 cfs and the 50-year flood is 5,300 cfs. Streamflow data have been collected on Glowegee Creek since 1948 at a station 0.5 mile south of West Milton. The average streamflow of Glowegee Creek at this station is 41 cfs or about 1.5 cfs per sq mi. The mean annual flood is 740 cfs and the 50-year flood is 2,250 cfs. The quality of the water in both Kayaderosseras Creek and Glowegee Creek is satisfactory for public supply and most industrial purposes. The mineral content of both streams is low--the dissolved-solids content averaging about 93 ppm in Kayaderosseras Creek and about 131 ppm in Glowegee Creek. The average hardness of water in Kayaderosseras Creek and Glowegee Creek is 68 ppm and 102 ppm, respectively. During periods of low flow, suspended sediment discharge in both streams is less than 10 tons per day, but during periods of high flow, the sediment discharge has been as great as 163 tons per day in Glowegee Creek and 437 tons per day in Kayaderosseras Creek.

Characterization of nutrients and fecal indicator bacteria at a concentrated swine feeding operation in Wake County, North Carolina, 2009-2011

USGS Publications Warehouse

Harden, Stephen L.; Rogers, Shane W.; Jahne, Michael A.; Shaffer, Carrie E.; Smith, Douglas G.

2012-01-01

Study sites were sampled for laboratory analysis of nutrients, total suspended solids (TSS), and (or) fecal indicator bacteria (FIB). Nutrient analyses included measurement of dissolved ammonia, total and dissolved ammonia + organic nitrogen, dissolved nitrate + nitrite, dissolved orthophosphate, and total phosphorus. The FIB analyses included measurement of Escherichia coli and enterococci. Samples of wastewater at the swine facility were collected from a pipe outfall from the swine housing units, two storage lagoons, and the spray fields for analysis of nutrients, TSS, and FIB. Soil samples collected from a spray field were analyzed for FIB. Monitoring locations were established for collecting discharge and water-quality data during storm events at three in-field runoff sites and two sites on the headwater stream (one upstream and one downstream) next to the swine facility. Stormflow samples at the five monitoring locations were collected for four storm events during 2009 to 2010 and analyzed for nutrients, TSS, and FIB. Monthly water samples also were collected during base-flow conditions at all four stream sites for laboratory analysis of nutrients, TSS, and (or) FIB.

Function of peatland located on secondary transformed peat-moorsh soils on the purification processes of groundwater and the impact of pH on the rates of the elution of organic matter

NASA Astrophysics Data System (ADS)

Wojciech Szajdak, Lech; Szczepański, Marek

2010-05-01

The investigation of peatland is used to show the water quality functioning with respect to different forms of nitrogen and carbon. The purification of ground water by the transect of 4.5 km long consisting organic soils (peat-moorsh soils) was estimated. This transect is located in the Agroecological Landscape Park in Turew, 40 km South-West of Poznan, West Polish Lowland. There is this transect along Wyskoć ditch. pH, the contents of total and dissolved organic carbon, total nitrogen, N-NO3-, N-NH4+ was measured. Additionally C/N factors of peats were estimated. The investigation has shown the impact of the peatland located on the secondary transformed peat - moorsh soils on the lowering of total nitrogen, ammonium, and nitrates as well as total and dissolved organic carbon in ground water. Peat-moorsh soils were described and classified according to Polish hydrogenic soil classification and World Reference Base Soil Notation. There are four investigated points along to Wyskoc ditch. Two times a month during entire vegetation season the following material was taken from this four chosen sites: samples of peat, from the depth of 0-20 cm, samples of water from the ditch, samples of ground water from wells established for this investigation. Samples of peat-moorsh soils were collected at the depth 0-20 cm. Soils were sampled two times a month from 10 sites of each site. Samples were air dried and crushed to pass a 1 mm-mesh sieve. These 10 sub-samples were mixed for the reason of preparing a 'mean sample', which used for the determination of pH (in 1M KCl), dissolved organic carbon (DOC), total organic carbon (TOC), total nitrogen (Ntotal), and N-NO3- as well as N-NH4+. In water from Wyskoć ditch pH, Ntotal, N-NO3-, N-NH4+, DTC (dissolved total carbon) and DOC (dissolved organic carbon) was measured. Ground water samples were collected from four wells established for this investigation. The water was filtered by the middle velocity separation and pH, N-total, N-NO3-, N-NH4+, DTC (dissolved total carbon) and DOC (dissolved organic carbon) ware measured. Peatland located on the secondary transformed peat - moorsh soils has revealed the lowering in ground water: nitrates 38.5%, N-organic 10%, N-total 24.5%, ammonium 38.7%, dissolved total carbon 33.1%, dissolved total inorganic carbon 10%, and dissolved organic carbon 57.5%. The elution of soil organic matter from peat-moorsh soils in broad range of pH and ionic strength was investigated. The rates of the reaction were calculated from the kinetics of first order reaction model. All experiments were repeated at different pH 6.0, 6.5, 7.0, 8.0, 8.5 of 0.5 M ammonium acetate buffer solution. The investigations have shown the impact of the properties of secondary transformed peat-moorsh soils on the rates of the dissolution of organic matter. The rates of organic matter elution for all samples of peats were significant different at four used wavelengths λ=272 nm, λ=320 nm, λ=465 nm, and λ=665 nm. It was observed that the rates increased between λ=272 nm and λ=320 nm and decreased from λ=465 nm to λ=665 nm. Although, the lowest values of the pseudo first-order rate constants measured at λ=665 nm for all samples of peats from four places ranged from 1.9524 10-4 s-1 to 2.7361 10-4 s-1. Therefore, the highest values of t0.5 ranged from 42.2 to 59.2 min for all samples from Zbęchy, Shelterbelt, Mostek and Hirudo. This work was supported by a grant No. N N305 3204 36 founded by Polish Ministry of Education.

Assessment of metal exposure, ecological status and required water quality monitoring strategies in small- to medium-size temperate rivers.

PubMed

Marijić, Vlatka Filipović; Perić, Mirela Sertić; Kepčija, Renata Matoničkin; Dragun, Zrinka; Kovarik, Ivana; Gulin, Vesna; Erk, Marijana

2016-01-01

The present study was undertaken to obtain a better understanding of the seasonal variability of total dissolved metal/metalloid levels and physicochemical parameters within small- to medium-size freshwater ecosystems in temperate climate region. The research was conducted in four seasons in the Sutla River, medium-size polluted, and the Črnomerec Stream, small-size unpolluted watercourse in Croatia. In the Sutla River, characterized by the rural/industrial catchment, physicochemical parameters and total dissolved metal concentrations of 21 trace and 4 macro elements were analysed downstream of the point source of pollution, the glass production facility, indicating for the first time their variability across four seasons. Based on dissolved oxygen, total dissolved solids, nutrient concentrations, conductivity and total chemical oxygen demand, quality status of the Sutla River was good, but moderate to poor during summer, what was additionally confirmed by the highest levels of the most of 25 measured metals/metalloids in summer. Comparison with the reference small-size watercourse, the Črnomerec Stream, indicated significant anthropogenic impact on the Sutla River, most evident for Fe, Mn, Mo, Ni, Pb, Rb and Tl levels (3-70-fold higher in the Sutla River across all seasons). Generally, presented results indicated significant decrease of the water quality in the anthropogenically impacted small- to medium-size watercourses in summer, regarding physicochemical water parameters and total dissolved metal/metalloid concentrations, and pointed to significant seasonality of these parameters. Confirmed seasonality of river ecological status indicates that seasonal assessment represents a prerequisite for proper classification of the water quality in small- to medium-size temperate rivers.

Coast Guard exposure to gasoline, MTBE, and benzene vapors during inspection of tank barges.

PubMed

Davenport, A C; Glynn, T J; Rhambarose, H

2000-01-01

A field study was conducted June through August 1996 in an attempt to quantify short-term exposure levels to Coast Guard personnel performing routine inspection activities aboard commercial tank barges carrying gasoline. Transfer and fleeting operations were monitored in the ports of Pittsburgh, Pa., Huntington, W.Va., Baton Rouge, La., and Galveston, Tex. A total of 43 personal and 68 area samples were analyzed for benzene and total hydrocarbons as gasoline ("gasoline"). Results can be summarized as follows: Personal exposure to benzene gave 15-min time-weighted-average (TWA) results ranging from <0.10 to 0.50 ppm. Area benzene levels ranged from <0.04 to 170 ppm. Personal monitoring for gasoline revealed a range of <2.0 to 590 mg/m3 with a GM of 23 mg/m3. Area sample results for gasoline ranged from 1.7 to 90,000 mg/m3. Twelve personal samples were collected for methyl-tert butyl ether (MTBE). Only two of these were above the limit of detection and had 15-min time-weighted averages of 22 ppm and 1.3 ppm. Eighteen MTBE area samples ranged in value from <3.0 to 38 ppm. Although none of the personal samples met or exceeded proposed or established short-term exposure standards, many of the area sampling results indicated that a significant risk of acute exposure exists in the vicinity of valves, pressure lines, and connections. This includes anticipated sources such as pressure vent valves as well as unexpected sources resulting from structural deficiencies onboard the vessels. These results further emphasize the value of safe work practices and proper vessel maintenance in controlling exposure to harmful chemicals.

Implications of Decreased Nitrite Concentrations on Clostridium perfringens Outgrowth during Cooling of Ready-to-Eat Meats.

PubMed

Myers, Megan I; Sebranek, Joseph G; Dickson, James S; Shaw, Angela M; Tarté, Rodrigo; Adams, Kristin R; Neibuhr, Steve

2016-01-01

Increased popularity of natural and organic processed meats can be attributed to the growing consumer demand for preservative-free foods, including processed meats. To meet this consumer demand, meat processors have begun using celery juice concentrate in place of sodium nitrite to create products labeled as no-nitrate or no-nitrite-added meat products while maintaining the characteristics unique to conventionally cured processed meats. Because of flavor limitations, natural cures with celery concentrate typically provide lower ingoing nitrite concentrations for ready-to-eat processed meats than do conventional cures, which could allow for increased growth of pathogens, such as Clostridium perfringens, during cooked product cooling such as that required by the U.S. Department of Agriculture. The objective of this study was to investigate the implications associated with reduced nitrite concentrations for preventing C. perfringens outgrowth during a typical cooling cycle used for cooked products. Nitrite treatments of 0, 50, and 100 ppm were tested in a broth system inoculated with a three-strain C. perfringens cocktail and heated with a simulated product thermal process followed by a typical cooling-stabilization process. The nitrite concentration of 50 ppm was more effective for preventing C. perfringens outgrowth than was 0 ppm but was not as effective as 100 ppm. The interaction between nitrite and temperature significantly affected (P < 0.05) C. perfringens outgrowth in both total population and number of vegetative cells. Both temperature and nitrite concentration significantly affected (P < 0.05) C. perfringens spore survival, but the interaction between nitrite and temperature did not have a significant effect (P > 0.05) on spore outgrowth. Results indicate that decreased nitrite concentrations (50 ppm) have increased potential for total C. perfringens population outgrowth during cooling and may require additional protective measures, such as faster chilling rates.

Efficacy of hypobromous acid as a hide-on carcass antimicrobial intervention.

PubMed

Schmidt, John W; Wang, Rong; Kalchayanand, Norasak; Wheeler, Tommy L; Koohmaraie, Mohammad

2012-05-01

Escherichia coli O157:H7 and Salmonella on cattle hides at slaughter are the main source of beef carcass contamination by these foodborne pathogens during processing. Hypobromous acid (HOBr) has been approved for various applications in meat processing, but the efficacy of HOBr as a hide antimicrobial has not been determined. In this study, the antimicrobial properties of HOBr were determined by spraying cattle hides at either of two concentrations, 220 or 500 ppm. Treatment of hides with 220 ppm of HOBr reduced the prevalence of E. coli O157:H7 on hides from 25.3 to 10.1% (P < 0.05) and reduced the prevalence of Salmonella from 28.3 to 7.1% (P < 0.05). Treatment of hides with 500 ppm of HOBr reduced (P < 0.05) the prevalence of E. coli O157:H7 on hides from 21.2 to 10.1% and the prevalence of Salmonella from 33.3 to 8.1%. The application of 220 ppm of HOBr reduced (P < 0.05) aerobic plate counts, total coliform counts, and E. coli counts on hides by 2.2 log CFU/ 100 cm(2). The use of 500 ppm of HOBr resulted in reductions (P < 0.05) of aerobic plate counts, total coliform counts, and E. coli counts by 3.3, 3.7, and 3.8 log CFU/100 cm(2), respectively, demonstrating that the use of higher concentrations of HOBr on hides resulted in additional antimicrobial activity. These results indicate that the adoption of a HOBr hide wash will reduce hide concentrations of spoilage bacteria and pathogen prevalence, resulting in a lower risk of carcass contamination.

Presence of lead in paint of toys sold in stores of the formal market of Bogotá, Colombia.

PubMed

Mateus-García, A; Ramos-Bonilla, J P

2014-01-01

Lead (Pb) is a non-essential metal. Exposure to lead has been associated with adverse health effects in both children and adults. Lead content in paint used in toys or children's products has been identified as both a potential and preventable source of childhood lead exposure. Twenty-four stores located in Bogotá (Colombia) were selected by cluster sampling to participate in the study. A random sample of 96 toys was purchased at these stores. Since one toy can have different paint colors, a total of 116 paint samples from 96 toys were analyzed for lead content. Paint samples were prepared by microwave digestion and lead was quantified using ICP-OES. For quality control purposes of the analytical method, spike samples and a certified reference material (NIST SRM 2582) were used. The lead content in paint ranged from below the method detection limit (5ppm) to 47,600ppm, with an average Pb concentration of 1024ppm and a median concentration of 5ppm. Eight (8) paint samples removed from five toys had lead concentrations exceeding the US regulatory limit for total lead content (90ppm). Brown paint and toys manufactured in Colombia were significantly associated with high concentrations of lead in paint. Furthermore, a statistically significant interaction between these two variables was also found. The results suggest that there is a potential risk of lead exposure from paint of toys sold in the formal market of Bogotá. Therefore, the implementation of a national surveillance program of lead content in children products is urgently needed. The risk of children's lead exposure identified in this study, which is completely preventable, could be present also in other developing countries. © 2013 Published by Elsevier Inc.

Larvicidal Activity of Centaurea bruguierana ssp. belangerana Against Anopheles stephensi Larvae.

PubMed

Khanavi, Mahnaz; Rajabi, Afsaneh; Behzad, Masoud; Hadjiakhoondi, Abbas; Vatandoost, Hassan; Abaee, Mohammad Reza

2011-01-01

In this study, the total 80% of MeOH extract and also petroleum ether, CHCl3, EtOAc, n-BuOH, and the remaining MeOH fractions obtained by solvent-solvent fractionation of the whole flowering samples of Centaurea bruguierana (DC.) Hand.-Mzt. ssp. belangerana (DC.) Bornm. (Asteraceae), namely "Baad-Avard", collected from Borazjan in Bushehr Province (Bushehr, Iran) were investigated for larvicidal activity against malaria vector, Anopheles stephensi Liston, according to WHO methods. The mortality rate of total extract and petroleum ether fraction in concentration of 40 ppm were 28% and 86% respectively and the other fractions were inactive. The probit regression analysis for the dose-response to petroleum ether fraction treatment of larvae exhibited the LC50 and LC90 values of 15.7 ppm and 48.3 ppm, respectively. As results showed, the larvicidal activity of the petroleum ether fraction would be due to the nonpolar compounds in the plant which further isolation and purification would obtain the more active compounds in lower concentrations useful for preparation of biological insecticides.

Larvicidal Activity of Centaurea bruguierana ssp. belangerana Against Anopheles stephensi Larvae

PubMed Central

Khanavi, Mahnaz; Rajabi, Afsaneh; Behzad, Masoud; Hadjiakhoondi, Abbas; Vatandoost, Hassan; Abaee, Mohammad Reza

2011-01-01

In this study, the total 80% of MeOH extract and also petroleum ether, CHCl3, EtOAc, n-BuOH, and the remaining MeOH fractions obtained by solvent-solvent fractionation of the whole flowering samples of Centaurea bruguierana (DC.) Hand.-Mzt. ssp. belangerana (DC.) Bornm. (Asteraceae), namely “Baad-Avard”, collected from Borazjan in Bushehr Province (Bushehr, Iran) were investigated for larvicidal activity against malaria vector, Anopheles stephensi Liston, according to WHO methods. The mortality rate of total extract and petroleum ether fraction in concentration of 40 ppm were 28% and 86% respectively and the other fractions were inactive. The probit regression analysis for the dose-response to petroleum ether fraction treatment of larvae exhibited the LC50 and LC90 values of 15.7 ppm and 48.3 ppm, respectively. As results showed, the larvicidal activity of the petroleum ether fraction would be due to the nonpolar compounds in the plant which further isolation and purification would obtain the more active compounds in lower concentrations useful for preparation of biological insecticides. PMID:24250419

Field measurement of alkalinity and pH

USGS Publications Warehouse

Barnes, Ivan

1964-01-01

The behavior of electrometric pH equipment under field conditions departs from the behavior predicted from Nernst's law. The response is a linear function of pH, and hence measured pH values may be corrected to true pH if the instrument is calibrated with two reference solutions for each measurement. Alkalinity titrations may also be made in terms of true pH. Standard methods, such as colorimetric titrations, were rejected as unreliable or too cumbersome for rapid field use. The true pH of the end point of the alkalinity titration as a function of temperature, ionic strength, and total alkalinity has been calculated. Total alkalinity in potable waters is the most important factor influencing the end point pH, which varies from 5.38 (0 ? C, 5 ppm (parts per million) HC0a-) to 4.32 (300 ppm HC0a-,35 ? C), for the ranges of variables considered. With proper precautions, the pH may be determined to =i:0.02 pH and the alkalinity to =i:0.6 ppm HCO3- for many naturally occurring bodies of fresh water.

Elemental distribution in seaweed, Gelidium abbottiorum along the KwaZulu-Natal Coastline, South Africa.

PubMed

Misheer, Natasha; Kindness, Andrew; Jonnalagadda, Sreekanth B

2006-01-01

The total concentrations of 7 selected metals, namely manganese, iron, zinc, titanium, boron, arsenic and mercury, were monitored for one annual cycle covering four seasons in the seaweed, Gelidium abbottiorum, at four sampling sites at Zinkwasi, Ballito, Treasure beach and Park Rynie along the South-East coastline of KwaZulu-Natal, South Africa to assess the current status of the marine environment. Inductively Coupled Plasma Optical Emission Spectrophotometry, Mercury Cold Vapour AAS, and Hydride Generation AAS were used for the determination of metal concentrations. Mn concentrations were particularly high in the G. abbottiorum species, followed by Fe, As and B concentrations which were in the 3-8 ppm range. Ti and Zn were in the 100-400 ppb range, while Hg was low and below 100 ppb. A typical sample of G. abbottiorum at Treasure beach, a site close to Durban metropolis in winter had Mn (8.6 ppm), Fe (4.6 ppm), As (5.6 ppm), B (3.0 ppm), Ti (420 ppb), Zn (167 ppb) and Hg (7.5 ppb). All metals recorded a decrease in concentrations from winter to spring with the exception of Hg. The Hg levels increased considerably from winter to spring.

Trophic influences on mercury accumulation in top pelagic predators from offshore New England waters of the northwest Atlantic Ocean.

PubMed

Teffer, Amy K; Staudinger, Michelle D; Taylor, David L; Juanes, Francis

2014-10-01

Trophic pathways and size-based bioaccumulation rates of total mercury were evaluated among recreationally caught albacore tuna (Thunnus alalunga), yellowfin tuna (Thunnus albacares), shortfin mako shark (Isurus oxyrinchus), thresher shark (Alopias vulpinus), and dolphinfish (Coryphaena hippurus) from offshore southern New England waters of the northwest Atlantic Ocean between 2008 and 2011. Mercury concentrations were highest in mako (2.65 ± 1.16 ppm) and thresher sharks (0.87 ± 0.71 ppm), and significantly lower in teleosts (albacore, 0.45 ± 0.14 ppm; yellowfin, 0.32 ± 0.09 ppm; dolphinfish, 0.20 ± 0.17 ppm). The relationship between body size and mercury concentration was positive and linear for tunas, and positive and exponential for sharks and dolphinfish. Mercury increased exponentially with δ (15)N values, a proxy for trophic position, across all species. Results demonstrate mercury levels are positively related to size, diet and trophic position in sharks, tunas, and dolphinfish, and the majority of fishes exhibited concentrations greater than the US EPA recommended limit. Copyright © 2014 Elsevier Ltd. All rights reserved.

Flow Estimate of Carbon Dioxide in a Amazon River Hydrological Station

NASA Astrophysics Data System (ADS)

Moura, J. M. S.; Ferreira, R. B., Jr.; Tapajós, R. P.

2014-12-01

Recent measurements in the Amazon suggest that the flow of CO2 in surface waters may reach the order of 1GT per year and isotopic analyzes suggest that this carbon is a direct result of organic matter degradation (OMD) in rivers and the measured concentration exceeds the value expected for there to be equilibrium with the atmosphere (Richey et al, 2002). This study aimed to measure and check the seasonal variability of CO2 fluxes in a range of six months (September 2013-February 2014) in the Strait Óbidos hydrological station located geographically in the coordinates 55 ° 1 '4 "S and 55 ° 31' 4" W. In addiction, it is intended to correlate the data with physical-chemical water parameters pH, dissolved oxygen (DO), and temperature and humidity. The method used for the measurement of CO2 concentration in the atmosphere-water interface is the floating chamber liked with an infrared gas analyzer (IRGA- Infrared Gas Analyzer). The physical-chemical parameters of water were measured using a multiparameter probe YSI Professional Plus model. The preliminary results shows values average CO2 flux was approximately 15.65 1,01ppm / m2s-1 for the months of September and October and between the months of November, 2013 and February 2014 the CO2 flux average was 4.40 + 1.94 ppm / m2s-1. In addiction to the high temperature in dry season, in the water column there is sufficient convection for the existence of gases transport from water to atmosphere, resulting in increase of exchange. Thus, the decreased amount of radiation and consequently the low temperatures in the humid period (on average 27.2 ° C) should affect the OMD in the river, responsible for the production of dissolved CO2. Keywords: CO2 flux, seasonal variability, amazon river

Randomly amplified polymorphic-DNA analysis for detecting genotoxic effects of Boron on maize (Zea mays L.).

PubMed

Sakcali, M Serdal; Kekec, Guzin; Uzonur, Irem; Alpsoy, Lokman; Tombuloglu, Huseyin

2015-08-01

This study was carried out to investigate the genotoxic effect of boron (B) on maize using randomly amplified polymorphic DNA (RAPD) method. Experimental design was conducted under 0, 5, 10, 25, 50, 100, 125, and 150 ppm B exposures, and physiological changes have revealed a sharp decrease in root growth rates from 28% to 85%, starting from 25 ppm to 150 ppm, respectively. RAPD-polymerase chain reaction (PCR) analysis shows that DNA alterations are clearly observed from beginning to 100 ppm. B-induced inhibition in root growth had a positive correlation with DNA alterations. Total soluble protein, root and stem lengths, and B content analysis in root and leaves encourage these results as a consequence. These preliminary findings reveal that B causes chromosomal aberration and genotoxic effects on maize. Meanwhile, usage of RAPD-PCR technique is a suitable biomarker to detect genotoxic effect of B on maize and other crops for the future. © The Author(s) 2013.

Photochemical Control of the Distribution of Venusian Water and Comparison to Venus Express SOIR Observations

NASA Astrophysics Data System (ADS)

Parkinson, Chris; Yung, Yuk; Esposito, Larry; Gao, Peter; Bougher, Steve

2014-11-01

We use the JPL/Caltech 1-D KINETICS photochemical model to solve the continuity diffusion equation for the atmospheric constituent abundances and total number density as a function of radial distance from the planet Venus. The photochemistry of the Venus atmosphere from 58 to 112 km is modeled using an updated and expanded chemical scheme (Zhang et al., 2010; 2012), guided by the results of recent observations. We mainly follow Zhang et al. (2010; 2012) to guide our choice of boundary conditions for 40 species. We fit the SOIR Venus Express results of 1 ppm at 70-90 km (Bertaux et al (2007) by modeling water from between 10 - 35 ppm at our 58 km lower boundary and using an SO2 mixing ratio of 25 ppm as our nominal reference value. We then vary the SO2 mixing ratio at the lower boundary between 5 and 75 ppm and find that it can control the water distribution at higher altitudes.

Responses of HSC70 expression in diencephalon to iron deficiency anemia in rats.

PubMed

Kawano, Fuminori; Oke, Yoshihiko; Nomura, Sachiko; Fujita, Ryo; Ohira, Takashi; Nakai, Naoya; Ohira, Yoshinobu

2011-11-01

A powdered diet containing 100 or 3 ppm Fe was fed to rats starting at the age of 3 weeks. The voluntary activity level was checked using a wheel in the cage during the 17th week after the beginning of supplementation. Significantly less activity was seen in the 3 ppm Fe group during both light and dark periods. After 20 weeks, the blood and diencephalon were sampled from both groups. Lower hematocrit and blood hemoglobin content was observed in the 3 ppm Fe group. The level of 70 kDa heat shock cognate (HSC70) expression was greater in the diencephalon of the 3 ppm Fe group. In addition, the distribution of HSC70 was determined by proximity ligation assay. More HSC70-positive as well as total cells were noted in several areas of the diencephalon of the iron-deficient rats. The altered expression and distribution of HSC70 might play some role in the neurological changes.

Organochlorine insecticide residues in ducklings and their dilution by growth.

PubMed

Charnetski, W A

1976-08-01

Residues of DDT, DDD, DDE, and dieldrin in 7 species of ducklings from Alberta, Canada, were measured. Levels of DDT and metabolites ranged from 0 to 36.48 ppm in fat of 96% of the birds and from 0 to 0.97 ppm im muscle from 67% of the birds. Residue levels of dieldrin ranged from 0 to 2.62 ppm in fat and from 0 to 0.11 ppm in muscle of 43 and 19% of the birds, respectively. Growth dilution was considered to be the most significant factor in reducing the insecticide residue levels in the ducklings. DDT (total DDT, DDE, and DDD) residue levels were decreased with increased weight of pintail (A. acuta), baldpate (Mareca americana), and gadwall (A. strepera) ducklings. Dieldrin used in grasshopper control did not contribute to residue levels in the ducklings. Contamination by DDT was considered to have originated from outside the habitat. No dieldrin or DDT residues were found in ducklings' food sources analysed.

Selenium in fly ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gutenmann, W.H.; Bache, C.A.; Youngs, W.D.

1976-03-05

Selenium, at concentrations exceeding 200 parts per million (ppM) (dry weight), has been found in white sweet clover voluntarily growing on beds of fly ash in central New York State. Guinea pigs fed such clover concentrated selenium in their tissues. The contents of the honey stomachs of bees foraging on this seleniferous clover contained negligible selenium. Mature vegetables cultured on 10 percent (by weight) fly ash-amended soil absorbed up to 1 ppM of selenium. Fly ashes from 21 states contained total selenium contents ranging from 1.2 to 16.5 ppM. Cabbage grown on soil containing 10 percent (by weight) of thesemore » fly ashes absorbed selenium (up to 3.7 ppM) in direct proportion (correlation coefficient r = .89) to the selenium concentration in the respective fly ash. Water, aquatic weeds, algae, dragonfly nymphs, polliwogs, and tissues of bullheads and muskrats from a fly ash-contaminated pond contained concentrations of selenium markedly elevated over those of controls.« less

Silicate Carbonation in Supercritical CO2 Containing Dissolved H2O: An in situ High Pressure X-Ray Diffraction Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaef, Herbert T.; Miller, Quin RS; Thompson, Christopher J.

2013-06-30

Technological advances have been significant in recent years for managing environmentally harmful emissions (mostly CO2) resulting from combustion of fossil fuels. Deep underground geologic formations are emerging as reasonable options for long term storage of CO2 but mechanisms controlling rock and mineral stability in contact with injected supercritical fluids containing water are relatively unknown. In this paper, we discuss mineral transformation reactions occurring between supercritical CO2 containing water and the silicate minerals forsterite (Mg2SiO4), wollastonite (CaSiO3), and enstatite (MgSiO3). This study utilizes newly developed in situ high pressure x-ray diffraction (HXRD) and in situ infra red (IR) to examine mineralmore » transformation reactions. Forsterite and enstatite were selected as they are important minerals present in igneous and mafic rocks and have been the subject of a large number of aqueous dissolution studies that can be compared with non-aqueous fluid tests in this study. Wollastonite, classified as a pyroxenoid (similar to a pyroxene), was chosen as a suitably fast reacting proxy for examining silicate carbonation processes associated with a wet scCO2 fluid as related to geologic carbon sequestration. The experiments were conducted under modest pressures (90 to 160 bar), temperatures between 35° to 70° C, and varying concentrations of dissolved water. Under these conditions scCO2 contains up to 3,500 ppm dissolved water.« less

Relation of pulmonary responses induced by 6.6-h exposures to 0.08 ppm ozone and 2-h exposures to 0.30 ppm ozone via chamber and face-mask inhalation.

PubMed

Adams, William C

2003-07-01

While direct comparison of pulmonary responses to 6.6-h exposures to 0.08 to 0.12 ppm ozone O3 have demonstrated that chamber and face-mask inhalation methods yield closely similar results, no comparative study of responses to 2-h intermittent exercise (IE) exposures to higher O3 concentrations have been reported. The present study was designed to achieve three primary objectives: (1) to compare pulmonary function and symptoms effects of a 2-h IE exposure to 0.30 ppm O3 via chamber and via face mask; (2) to compare the pulmonary effects of 6.6-h chamber exposure to 0.08 ppm O3 to those observed in 2-h IE 0.30 ppm O3 exposures via chamber and via face mask; and (3) to examine filtered air (FA) recovery pulmonary and symptoms responses following chamber exposures of 6.6 h to 0.08 ppm O3 and 2 h to 0.30 ppm O3. A simple regression of postexposure percent change in FEV(1.0) for the 2-h IE, 0.30-ppm O3 chamber exposure as a function of postexposure percent change in FEV(1.0) for the 2-h IE, 0.30-ppm O3 exposure with face mask yielded an R(2) of 0.83. Further, a regression of the postexposure FEV(1.0) response to the chamber 6.6-h, 0.08-ppm O3 exposure as a function of postexposure FEV(1.0) response to the face mask 2-h IE, 0.30-ppm O3 exposure (R(2) of 0.34) was similar to the 0.40 value obtained for the two chamber exposures FEV(1.0) response comparison. Results of the 1.4-h FA recovery following the two chamber O3 exposures showed different rates of FEV(1.0) and symptoms rectification that appeared related to the total O3 dose (product of O3 concentration, ventilation rate, and duration). More data are needed to clarify short-term recovery of O3-induced pulmonary effects and how they may be related to the more abundant data available on the delayed recovery of pulmonary function seen over longer time periods, such as 24 h.

IgE sensitization to Thaumetopoea pityocampa : diagnostic utility of a setae extract, clinical picture and associated risk factors.

PubMed

Vega, José María; Moneo, Ignacio; García-Ortiz, José Carlos; González-Muñoz, Miguel; Ruiz, Carmen; Rodríguez-Mahillo, Ana Isabel; Roques, Alain; Vega, Jesús

2014-01-01

Setae from Thaumetopoea pityocampa larvae (the pine processionary moth or PPM) can induce hypersensitivity reactions, but their clinical role in IgE-mediated responses is still subject to discussion. The aim of this study was to evaluate a setae extract for in vivo and in vitro diagnosis in nonhospitalized patients with reactions to PPM. Forty-eight adult patients presenting with PPM cutaneous reactions were studied by skin prick test (SPT) and specific IgE using setae and whole larval (WL) extracts. Biological standardized extracts were used for skin tests. A total of 47.9% patients had a positive SPT for PPM (70% to both extracts, 17% only to the WL extract and 13% only to the setae extract). IgE immunoblotting detected several reactive bands in 91% of the SPT-positive cases. In multivariate analysis, male sex, immediate latency (<1 h) and duration of skin symptoms (<24 h) were independent predictors of a positive SPT. IgE sensitization to PPM was found in 48% of the study patients, which was associated with immediate reactions and evanescent cutaneous lesions. Most of these patients reacted to both WL and setae extracts, but some reacted to only one of them. According to our data, skin and in vitro tests to PPM should be performed using both extracts. © 2015 S. Karger AG, Basel.

Measurement of volume resistivity/conductivity of metallic alloy in inhibited seawater by optical interferometry techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Habib, K.

2011-03-15

Optical interferometry techniques were used for the first time to measure the volume resistivity/conductivity of carbon steel samples in seawater with different concentrations of a corrosion inhibitor. In this investigation, the real-time holographic interferometry was carried out to measure the thickness of anodic dissolved layer or the total thickness, U{sub total}, of formed oxide layer of carbon steel samples during the alternating current (ac) impedance of the samples in blank seawater and in 5-20 ppm TROS C-70 inhibited seawater, respectively. In addition, a mathematical model was derived in order to correlate between the ac impedance (resistance) and the surface (orthogonal)more » displacement of the surface of the samples in solutions. In other words, a proportionality constant [resistivity ({rho}) or conductivity ({sigma})= 1/{rho}] between the determined ac impedance [by electrochemical impedance spectroscopy (EIS) technique] and the orthogonal displacement (by the optical interferometry techniques) was obtained. The value of the resistivity of the carbon steel sample in the blank seawater was found similar to the value of the resistivity of the carbon steel sample air, around 1 x 10{sup -5}{Omega} cm. On the contrary, the measured values of the resistivity of the carbon steel samples were 1.85 x 10{sup 7}, 3.35 x 10{sup 7}, and 1.7 x 10{sup 7}{Omega} cm in 5, 10, and 20 ppm TROS C-70 inhibited seawater solutions, respectively. Furthermore, the determined value range of {rho} of the formed oxide layers, from 1.7 x 10{sup 7} to 3.35 x 10{sup 7}{Omega} cm, is found in a reasonable agreement with the one found in literature for the Fe oxide-hydroxides, i.e., goethite ({alpha}-FeOOH) and for the lepidocrocite ({gamma}-FeOOH), 1 x 10{sup 9}{Omega} cm. The {rho} value of the Fe oxide-hydroxides, 1 x 10{sup 9}{Omega} cm, was found slightly higher than the {rho} value range of the formed oxide layer of the present study. This is because the former value was determined by a dc method rather than by an electromagnetic method, i.e., holographic interferometry with applications of EIS, i.e., ac method. As a result, erroneous measurements were recorded due to the introduction of heat to Fe oxide-hydroxides.« less

Seasonal ice and hydrologic controls on dissolved organic carbon and nitrogen concentrations in a boreal-rich fen

Treesearch

Evan S. Kane; Merritt R. Turetsky; Jennifer W. Harden; A. David McGuire; James M. Waddington

2010-01-01

Boreal wetland carbon cycling is vulnerable to climate change in part because hydrology and the extent of frozen ground have strong influences on plant and microbial functions. We examined the response of dissolved organic carbon (DOC) and total dissolved nitrogen (TDN) across an experimental manipulation of water table position (both raised and lowered water table...

Water quality and phytoplankton of the tidal Potomac River, August-November 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woodward, J.C.; Manning, P.D.; Shultz, D.J.

1984-01-01

In the summer of 1983, a prolonged blue-green algal bloom, consisting predominantly of Microcystis, occurred in the Potomac River downstream of Washington, DC. Ten longitudinal sampling trips were made between August 3 and November 9, 1983, primarily in the freshwater tidal Potomac River between Memorial Bridge and Quantico, Va. Samples were depth-integrated and composited across the river at each major station and analyzed for dissolved and total nitrogen species, dissolved and total phosphorus species, dissolved silica, chlorophyll-a, pheophytin, and suspended sediment. In addition, phytoplankton were enumerated and identified. Point samples were taken for chlorophyll-a and pheophytin, and measurements were mademore » of dissolved oxygen, pH, conductance, temperature, and Secchi disc transparency. Some supplementary data are presented from points between major stations and in tributaries to the tidal Potomac River. 14 refs., 3 figs., 8 tabs.« less

Dissolved and Particulate 230Th - 232Th systematics in the Central Equatorial Pacific Ocean

NASA Astrophysics Data System (ADS)

Lopez, G. I.; Marcantonio, F.

2013-12-01

To complement our work in the eastern Equatorial Pacific, we have measured total and dissolved 230Th and 232Th in the central Equatorial Pacific at two sites, one at 8°N and the other at the equator (ML1208-03CTD; 00° 13.166' S, 155° 57.668' W and ML1208-12CTD; 8° 19.989' N, 159° 18.000' W). The two seawater casts were collected in May 2012 during an NSF-funded "Line Islands" cruise to test for the extent of advection or diffusion of dissolved 230Th from the oligotrophic North Pacific gyre (low particle flux) to the more productive equatorial region (high particle flux). Our thorium results are similar to previous data published for the western and central North Pacific Ocean. Dissolved 230Th concentrations range from 1.1 fg/kg at 100 m to 30.8 fg/kg at 4400 m, while dissolved 232Th concentrations span from 8.1 pg/kg at 900 m to 19.7 pg/kg at 4400 m. The pattern of the dissolved 230Th profile at 8°N is essentially linear from the surface to 2000 m. From 2000 m to 3000 m, the dissolved 230Th concentrations are constant, and then from 3000 m to the bottom, the profile is linear again. At the same site, the particulate fraction of the total seawater 230Th increases exponentially from about 0% at the surface to 38% at 4400 m. From 0 to 3000 m at 8°N, dissolved 232Th concentrations display a relatively constant pattern (variability of about 20%). From 3000 m to 4400 m, dissolved 232Th contents are more variable, but generally increase toward greater depths. The proportion of 232Th in the particulate fraction of the total seawater sample increases exponentially with depth to a value of 58% in the bottommost sample. We will present additional data from the equator and assess the particulate dynamics that control the distribution of thorium isotopes in central equatorial Pacific seawater.

Water-Quality Data Collected from Vallecito Reservoir, Its Inflows and Outflow, Southwestern Colorado, 1999-2002

USGS Publications Warehouse

Ranalli, Anthony J.

2008-01-01

The Pine River Watershed Stakeholders Group was created in December 1997 to allow local participation in addressing water-quality issues in Los Pi?os River watershed, including Vallecito Reservoir in southwestern Colorado. One water-quality issue identified by the stakeholder group is to increase the understanding of the current water quality of Vallecito Reservoir, its two major inflows, and its outflow. The U.S. Geological Survey (USGS), in cooperation with volunteers from the Pine River Watershed Stakeholders Group and the U.S. Environmental Protection Agency (USEPA), U.S. Bureau of Reclamation (BOR), Colorado Department of Public Health and Environment (CDPHE), Pine River Irrigation District, Southern Ute Tribe, San Juan Basin Health Department, and San Juan Resource Conservation and Development, collected water-quality samples from Vallecito Reservoir, its two major inflows, and its outflow between August 1999 and November 2002 at about monthly intervals from April through November. The water-quality samples were analyzed for total and dissolved metals (aluminum, arsenic, cadmium, copper, chromium, iron, lead, manganese, mercury, nickel, silver, and zinc), dissolved major ions (calcium, magnesium, sodium, potassium, chloride, bicarbonate, and sulfate), dissolved silica, dissolved organic carbon (DOC), ultraviolet (UV) absorbance at 254 and 280 nanometers, nutrients (total organic nitrogen, dissolved organic nitrogen, dissolved ammonia, dissolved nitrate, total phosphorus, dissolved phosphorus, and orthophosphate), chlorophyll-a (reservoir only), and suspended sediment (inlets to the reservoir only). Measurements of field properties (pH, specific conductance, water temperature, and dissolved oxygen) were also made at each sampling site each time a water-quality sample was collected. This report documents (1) sampling sites and times of sample collection, (2) sample-collection methods, (3) laboratory analytical methods, and (4) responsibilities of each agency/group involved in the project. The report also provides the environmental and quality-control data collected during the project and provides an interpretation of the quality-control data (field blanks and field duplicates) to assess the quality of the environmental data. This report provides a baseline data set against which future changes in water quality can be assessed.

Physical and chemical characteristics of water from the hydrographic basin of the Poxim River, Sergipe State, Brazil.

PubMed

de Aguiar Netto, Antenor Oliveira; Garcia, Carlos Alexandre Borges; Hora Alves, José do Patrocínio; Ferreira, Robério Anastácio; Gonzaga da Silva, Marinoé

2013-05-01

The Poxim River is one of Sergipe State's major waterways. It supplies water to the State capital, Aracaju, but is threatened by urban and agricultural developments that compromise both the quantity and the quality of the water. This has direct impacts on the daily lives of the region's population. In this work, a multivariate analytical approach was used to investigate the physical and chemical characteristics of the water in the river basin. Four sampling campaigns were undertaken, in November 2005, and in February, May, and September 2006, at 15 sites distributed along the Poxim. The parameters analyzed were conductivity, turbidity, color, total dissolved solids, dissolved oxygen, alkalinity, hardness, chlorophyll-a, and nutrients (total phosphorus, dissolved orthophosphate, nitrite, nitrate, ammoniacal nitrogen, and total nitrogen). Dissolved oxygen contents were very low in the Poxim-Açu River (1.0-2.8), the Poxim River (1.6-4.6), and the estuarine region (1.7-5.1), due to the dumping of wastes and discharges of domestic and industrial effluents containing organic matter into fluvial and estuarine regions of the Poxim. Factor analysis identified five components that were indicative of the quality of the water, and that explained 81.73 % of the total variance.

Transcatheter Heart Valve Selection and Permanent Pacemaker Implantation in Patients With Pre-Existent Right Bundle Branch Block.

PubMed

van Gils, Lennart; Tchetche, Didier; Lhermusier, Thibault; Abawi, Masieh; Dumonteil, Nicolas; Rodriguez Olivares, Ramón; Molina-Martin de Nicolas, Javier; Stella, Pieter R; Carrié, Didier; De Jaegere, Peter P; Van Mieghem, Nicolas M

2017-03-03

Right bundle branch block is an established predictor for new conduction disturbances and need for a permanent pacemaker (PPM) after transcatheter aortic valve replacement. The aim of the study was to evaluate the absolute rates of transcatheter aortic valve replacement related PPM implantations in patients with pre-existent right bundle branch block and categorize for different transcatheter heart valves. We pooled data on 306 transcatheter aortic valve replacement patients from 4 high-volume centers in Europe and selected those with right bundle branch block at baseline without a previously implanted PPM. Logistic regression was used to evaluate whether PPM rate differed among transcatheter heart valves after adjustment for confounders. Mean age was 83±7 years and 63% were male. Median Society of Thoracic Surgeons score was 6.3 (interquartile range, 4.1-10.2). The following transcatheter valve designs were used: Medtronic CoreValve (n=130; Medtronic, Minneapolis, MN); Edwards Sapien XT (ES-XT; n=124) and Edwards Sapien 3 (ES-3; n=32; Edwards Lifesciences, Irvine, CA); and Boston Scientific Lotus (n=20; Boston Scientific Corporation, Marlborough, MA). Overall permanent pacemaker implantation rate post-transcatheter aortic valve replacement was 41%, and per valve design: 75% with Lotus, 46% with CoreValve, 32% with ES-XT, and 34% with ES-3. The indication for PPM implantation was total atrioventricular block in 98% of the cases. Lotus was associated with a higher PPM rate than all other valves. PPM rate did not differ between ES-XT and ES-3. Ventricular paced rhythm at 30-day and 1-year follow-up was present in 81% at 89%, respectively. Right bundle branch block at baseline is associated with a high incidence of PPM implantation for all transcatheter heart valves. PPM rate was highest for Lotus and lowest for ES-XT and ES-3. Pacemaker dependency remained high during follow-up. © 2017 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley Blackwell.

Sulindac, 3,3'-diindolylmethane and curcumin reduce carcinogenesis in the Pirc rat, an Apc-driven model of colon carcinogenesis.

PubMed

Femia, Angelo Pietro; Soares, Paulo Victoria; Luceri, Cristina; Lodovici, Maura; Giannini, Augusto; Caderni, Giovanna

2015-09-03

Recently, we showed that Sulindac (SU; 320 ppm) reduces precancerous lesions in the colon of Pirc rats, mutated in the Apc gene. Surprisingly, previous data in Apc-mutated mice showed that SU, with reported efficacy in Familial Adenomatous Polyposis (FAP), increases colon carcinogenesis. Therefore, we assessed the effect of SU 320 ppm in a long-term carcinogenesis experiment in Pirc rats. Moreover, since side effects of SU hamper its chronic use and a combination of drugs could be more effective and less toxic than single agents, we also studied whether two natural compounds, 3,3'-diindolylmethane (DIM; 250 ppm) and curcumin (CUR; 2000 ppm), with or without lower doses of SU could affect carcinogenesis Pirc rats were fed an AIN76 diet containing SU, DIM and CUR and sacrificed at 8 months of age to measure intestinal tumours. Apoptosis and proliferation in the normal colon mucosa, as well as gene expression profile were studied Colon tumours were significantly reduced by SU 320 ppm (62 % reduction over Controls), by DIM and CUR without or with SU 80 and 160 ppm (50, 53 and 58 % reduction, respectively) but not by SU 80 ppm alone. Total tumours (colon and small intestine) were reduced by SU (80 and 320 ppm) and by DIM and CUR. Apoptosis in the normal mucosa was significantly increased by SU 320 ppm, and slightly increased by DIM and CUR with or without SU. A slight reduction in Survivin-Birc5 expression was observed with all the treatments compared to Controls. Proliferative activity was not varied The results on SU reinforce the validity of Pirc rats to identify chemopreventive products. Moreover, the efficacy of the DIM and CUR combination to lower colon tumours, suggests an alternative strategy to be exploited in patients at risk.

Total mercury concentrations in lionfish (Pterois volitans/miles) from the Florida Keys National Marine Sanctuary, USA.

PubMed

Huge, Dane H; Schofield, Pamela J; Jacoby, Charles A; Frazer, Thomas K

2014-01-15

Strategies to control invasive lionfish in the western Atlantic and Caribbean are likely to include harvest and consumption. Until this report, total mercury concentrations had been documented only for lionfish from Jamaica, and changes in concentrations with increasing fish size had not been evaluated. In the Florida Keys, total mercury concentrations in dorsal muscle tissue from 107 lionfish ranged from 0.03 to 0.48 ppm, with all concentrations being less than the regulatory threshold for limited consumption. Mercury concentrations did not vary consistently with standard lengths or wet weights of lionfish. In 2010, lionfish from the upper Keys had mean concentrations that were 0.03-0.04 ppm higher than lionfish from the middle Keys, but mean concentrations did not differ consistently among years and locations. Overall, total mercury concentrations in lionfish were lower than those in several predatory fishes that support commercial and recreational fisheries in Florida. Published by Elsevier Ltd.

Concentration and flux of total and dissolved phosphorus, total nitrogen, chloride, and total suspended solids for monitored tributaries of Lake Champlain, 1990-2012

USGS Publications Warehouse

Medalie, Laura

2014-01-01

Annual and daily concentrations and fluxes of total and dissolved phosphorus, total nitrogen, chloride, and total suspended solids were estimated for 18 monitored tributaries to Lake Champlain by using the Weighted Regressions on Time, Discharge, and Seasons regression model. Estimates were made for 21 or 23 years, depending on data availability, for the purpose of providing timely and accessible summary reports as stipulated in the 2010 update to the Lake Champlain “Opportunities for Action” management plan. Estimates of concentration and flux were provided for each tributary based on (1) observed daily discharges and (2) a flow-normalizing procedure, which removed the random fluctuations of climate-related variability. The flux bias statistic, an indicator of the ability of the Weighted Regressions on Time, Discharge, and Season regression models to provide accurate representations of flux, showed acceptable bias (less than ±10 percent) for 68 out of 72 models for total and dissolved phosphorus, total nitrogen, and chloride. Six out of 18 models for total suspended solids had moderate bias (between 10 and 30 percent), an expected result given the frequently nonlinear relation between total suspended solids and discharge. One model for total suspended solids with a very high bias was influenced by a single extreme value; however, removal of that value, although reducing the bias substantially, had little effect on annual fluxes.

Hepatic glutathione metabolism and lipid peroxidation in response to excess dietary selenomethionine and selenite in mallard ducklings

USGS Publications Warehouse

Hoffman, D.J.; Heinz, G.H.; Krynitsky, A.J.

1989-01-01

Selenium from selenomethionine accumulated in a dose-dependent manner in the liver, resulting in a decrease in hepatic-reduced glutathione with a corresponding decrease in total hepatic thiols. There was a dose-dependent increase in the oxidized to reduced glutathione ratio, and an increase in lipid peroxidation. These findings indicate that Se in the diet at 10 ppm and higher causes significant sublethal alterations in mallard ducklings, and 20-40 ppm causes significant hepatotoxicity.

Distribution of mercury in the deep sea water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takizawa, Y.; Amano, Y.

1974-01-01

A study was performed to determine why deep sea fish and shellfish contain a large percentage of mercury. The material selected for study consisted of sediments, corals, seaweeds, and seawater. Total mercury was determined by ultraviolet atomic absorption, and methylmercury was analyzed via gas chromatography. The sediments of the Japan Sea bed contained low (0.001-0.011 ppm) amounts of total mercury. Methylmercury was not detected in the sediments. In corals, total mercury varied according to age; there was a tendency for the accumulation to be larger in the modern living coral than in the old corals. Mercury concentrations in seaweeds variedmore » from none to 0.032 ppm. Methylmercury was not detected in seaweeds. The concentrations detected in this study cannot explain the high levels found in fish and shellfish. The authors speculate that a food chain transfer is operating, its structure being phytoplankton-based. 3 tables.« less

Phenotypic and biochemical profile changes in calendula (Calendula officinalis L.) plants treated with two chemical mutagenesis.

PubMed

El-Nashar, Y I; Asrar, A A

2016-05-06

Chemical mutagenesis is an efficient tool used in mutation-breeding programs to improve the vital characters of the floricultural crops. This study aimed to estimate the effects of different concentrations of two chemical mutagens; sodium azide (SA) and diethyl sulfate (DES). The vegetative growth and flowering characteristics in two generations (M1 and M2) of calendula plants were investigated. Seeds were treated with five different concentrations of SA and DES (at the same rates) of 1000, 2000, 3000, 4000, and 5000 ppm, in addition to a control treatment of 0 ppm. Results showed that lower concentrations of SA mutagen had significant effects on seed germination percentage, plant height, leaf area, plant fresh weight, flowering date, inflorescence diameter, and gas-exchange measurements in plants of both generations. Calendula plants tended to flower earlier under low mutagen concentrations (1000 ppm), whereas higher concentrations delayed flowering significantly. Positive results on seed germination, plant height, number of branches, plant fresh weight, and leaf area were observed in the M2-generation at lower concentrations of SA (1000 ppm), as well as at 4000 ppm DES on number of leaves and inflorescences. The highest total soluble protein was detected at the concentrations of 1000 ppm SA and 2000 ppm DES. DES showed higher average of acid phosphatase activity than SA. Results indicated that lower concentrations of SA and DES mutagens had positive effects on seed germination percentage, plant height, leaf area, plant fresh weight, flowering date, inflorescence diameter, and gas-exchange measurements. Thus, lower mutagen concentrations could be recommended for better floral and physio-chemical performance.

Effects of alkylphenols on redox status in first spawning Atlantic cod (Gadus morhua).

PubMed

Hasselberg, Linda; Meier, Sonnich; Svardal, Asbjørn

2004-07-30

Offshore oil production releases large amounts of lipophilic compounds in produced water and into the ocean. The discharge of produced water from the Norwegian petroleum sector has increased from 26 million m3 in 1993 to 120 million m3 in 2001, and it continues to increase. Produced water contains significant amounts of alkylphenols, which have been reported to be estrogenic, causing endocrine disruption in fish. In year 2000, approximately 44 tons of alkylphenols were released on the Norwegian continental shelf in connection with discharge of produced water. Except from being estrogenic, relatively little is known about the effects of alkylphenols when released in the marine environment. Our objective was to study how alkylphenols affect the redox status in first spawning Atlantic cod (Gadus morhua) of both sexes. Model compounds tested included 4-tert-butylphenol (C4), 4-n-pentylphenol (C5), 4-n-hexylphenol (C6) and 4-n-heptylphenol (C7), all found in produced water. First spawning Atlantic cod were force-fed a mixture of these four alkylphenols, ranging between 0.02 and 80 ppm or 5 ppm 17beta-estradiol (E2), for 1 or 4 weeks. Increased hepatic total glutathione concentration in response to alkylphenol exposure was detected in female fish compared to control group after 1-week exposure, an effect not seen after 4 weeks. Furthermore, hepatic total glutathione concentration was sex dependent, where male fish sampled after 4 weeks had higher levels of glutathione than female fish. Increased glutathione reductase catalytic activities in both male and female fish were seen after exposure to 0.02 ppm alkylphenol mixture in 4 weeks. The glutathione S-transferase activity was only affected in male fish exposed to 0.02 ppm alkylphenols, and glucose-6-phosphate dehydrogenase activity increased in female fish exposed to 0.02 ppm alkylphenol mixture for 1 week. The increase of hepatic total glutathione content as well as the effects on glutathione reductase activities suggests that alkylphenol exposure affects the redox status in Atlantic cod. Copyright 2004 Elsevier B.V.

ENHANCED CHEMICAL CLEANING: EFFECTIVENESS OF THE UV LAMP TO DECOMPOSE OXALATES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ketusky, E.; Huff, T.; Sudduth, C.

2010-01-19

Enhanced Chemical Cleaning is a new process scheduled to begin cleaning Savannah River Site High Level Waste Tanks in 2012. It is an improvement over the current chemical cleaning method, in that it minimizes downstream impacts on the High Level Waste System. It is based on a state of the art scale removal process used on the secondary side of nuclear power plants, with modifications to accommodate the unique constraints created by the tanks. Both Enhanced Chemical Cleaning and the scale removal process are founded on dissolving metal oxides/hydroxides using oxalic acid, with subsequent oxalate decomposition via hydroxylation using ozonemore » or peroxide, and UV light as a catalyst. A divergence Enhanced Chemical Cleaning has from nuclear power scale removal is the significantly increased solids concentration during oxalate decomposition. These solids can limit the ability of the UV light to create hydroxyl radicals, either by limiting the ability of the light to penetrate through the solution, or by increasing the fouling rate on the UV light. Both will decrease the overall catalytic effectiveness, thereby decreasing the concentration of formed hydroxyl radicals. The hydroxyl radicals are the driving force behind the oxalate decomposition. To understand the impact of increased solids, testing was performed using a medium pressure UV light inside an ozone supplied Oxalate Decomposition Reactor. Using a dissolved metal sludge simulant with an initial oxalate concentration greater than 12,000 ppm, and an initial pH of about 2.0, the spent acid solution was recirculated through the reactor, while the UV light was allowed to foul. For the first few hours, the oxalate decomposition rate was about 1,300 ppm/hour. After about 3 hours, enough time for the UV lamp to foul, the oxalate decomposition rate decreased to about 500 ppm/hour. The decomposition rate then remained roughly constant for the next 16 hours. Overall, testing showed that the oxalate destruction rate decreased by about 2.8. Results from very similartests with similar chemistry suggest that the impact should be about 10. Based on the limited reaction pathwayfor the creation of hydroxyl radicals with iron, ozone, and no UV, the discrepancy suggests that initially, at 'time zero' the UV light failed to perform up to expectations. It is therefore concluded that regardless of the fouling rate, either the increased solids concentration is impacting the initial penetrability (i.e. to many solids), or the light is not adequately sized/configured to have the appropriate flux.« less

Water resources of the Mobile area, Alabama, with a section on salinity of the Mobile River

USGS Publications Warehouse

Robinson, W.H.; Powell, William J.; Brown, Eugene; Corps of Engineers, U.S. Army

1956-01-01

Water is an abundant resource of the Mobile area. The Mobile River has an estimated average flow of 60, 000 cubic feet per second (cfs), or about 39,000 million gallons per day (mgd). It is the largest single source of water. Water is available in substantial quantities from the many local streams and extensive water-bearing formations almost anywhere in the area. Surface water is low in dissolved mineral matter and is extremely soft. Salt water moving up the Mobile River from Mobile Bay during periods of low river flow, however, limits the use of that stream as a source of supply. The principal water-bearing formations are the alluvium and sediments of Miocene age. The Miocene strata dip toward the southwest, forming an artesian basin in the downtown area of Mobile. Small groundwater supplies can be developed practically everywhere, and supplies for industrial or other large-scale uses are available north of Mobile. The average use of water from all sources in the area during 1954 was about 356 mgd, of which about 20 mgd was used for domestic supplies and 336 mgd was used by industry. An estimated 42 mgd of ground water is used in the Mobile area. The discharge from wells used by industry ranges from 10 to 1,500 gallons per minute (gpm}, and the specific capacity of the large-capacity wells ranges from less than 6 to about 6 3 gpm per foot of drawdown. Concentrated pumping in the downtown area of Mobile between 1941 and 1945 resulted in encroachment of salt water from the Mobile River into the alluvium. Because of a decrease in pumping in that vicinity, the sodium chloride content of the water has decreased substantially since 1945. The quality of ground water is variable. Hardness of waters sampled ranged from 1 to 2, 190 parts per million (ppm}, the dissolved solids from 27 to 13, 000 ppm, and the chloride from 2.2 to 6,760 ppm. The water of best quality occurs between McIntosh and Prichard, and the water of poorest quality occurs in the downtown area of Mobile. The water-supply systems presently developed in the metropolitan area could furnish a moderate increase without taxing their facilities; with some increase in plant and pumping facilities, they could support a substantial increase. Industries outside the metropolitan area must develop their own supplies from local streams or wells.

C-1s NEXAFS spectroscopy reveals chemical fractionation of humic acid by cation-induced coagulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christl,I.; Kretzschmar, R.

2007-01-01

The influence of cation-induced coagulation on the chemical composition of dissolved and coagulated fractions of humic acid was investigated in batch coagulation experiments for additions of aluminum at pH 4 and 5, iron at pH 4, and calcium and lead at pH 6. The partitioning of organic carbon and metals was determined by analyzing total organic carbon and total metal contents of the dissolved phase. Both the dissolved and the coagulated humic acid fractions were characterized using synchrotron scanning transmission X-ray microscopy (STXM) and C-1s near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. Intensities of {pi}* transitions of carboxyl carbon andmore » {sigma}* transitions of alkyl, O-alkyl, and carboxyl carbon decreased with increasing metal concentration for the dissolved humic acid fractions. This decrease was accompanied by an increase of the respective intensities in the coagulated fraction as shown for lead. Intensities of aromatic and phenolic carbon were affected to a larger extent only by aluminum and iron additions. The changes observed in the C-1s NEXAFS spectra coincided with an increasing removal of organic carbon from the dissolved phase with increasing total metal concentrations. We conclude that humic acid was chemically fractionated by cation-induced coagulation, which preferentially removed functional groups involved in metal-cation binding from solution.« less

Geohydrology and water quality of Kalamazoo County, Michigan, 1986-88

USGS Publications Warehouse

Rheaume, S.J.

1990-01-01

Thick, glacial sand and gravel deposits provide most ground-water supplies in Kalamazoo County. These deposits range in thickness from 50 to about 600 feet in areas that overlie buried bedrock valleys. Most domestic wells completed at depths of less than 75 feet in the sands and gravels yield adequate water supplies. Most industry, public supply, and irrigation wells completed at depths of 100 to 200 feet yield 1,000 gallons per minute or more. The outwash plains include the most productive of the glacial aquifers in the county. The Coldwater Shale of Mississippian age, which underlies the glacial deposits in most of the county, usually yields only small amounts of largely mineralized water. Ground-water levels in Kalamazoo County reflect short- and long-term changes in precipitation and local pumpage. Ground-water levels increase in the spring and decline in the fall. Ground-water recharge rates, for different geologic settings, were estimated from ground-water runoff to the streams. Recharge rates ranged from 10.86 to 5.87 inches per year. A countywide-average ground-water recharge rate is estimated to be 9.32 inches per year. Chemical quality of precipitation and dry fallout at two locations in Kalamazoo County were similar to that of other areas in the State. Total deposition of dissolved sulfate is 30.7 pounds per acre per year, of total nitrogen is 13.2 pounds per acre per year, and of total phosphorus is 0.3 pounds per acre per year. Rainfall and snow data indicated that the pH of precipitation is inversely proportional to its specific conductance. Water of streams and rivers of Kalamazoo County is predominately of the calcium bicarbonate type, although dissolved sulfate concentrations are slightly larger in streams in the southeastern and northwestern parts of the county. The water in most streams is hard to very hard. Concentrations of dissolved chloride in streams draining urban-industrial areas are slightly larger than at other locations. Concentrations of total nitrogen and total phosphorus in streams are directly proportional to streamflow. Except for elevated concentrations of iron, none of the trace elements in streams exceeded maximum contaminant levels for drinking water established by the U.S. Environmental Protection Agency. Pesticides were detected in some streams. Ground water in the surficial aquifers is of the calcium bicarbonate type, although sodium, sulfate, and chloride ions predominate at some locations. Specific conductance and hardness and concentrations of total dissolved-solids slightly exceed statewide averages. Concentrations of dissolved sodium and dissolved chloride in 6 wells were greater than most natural ground waters in the State, indicating possible contamination from road salts. Water samples from 6 of the 46 wells sampled contained concentrations of total nitrate as nitrogen greater than 10.0 milligrams per liter. Elevated concentrations of total nitrate as nitrogen in water from wells in rural-agricultural areas probably are related to fertilizer applications. Results of partial chemical analyses by the Michigan Department of Public Health indicates specific conductance, and concentrations of hardness, dissolved fluoride, and total iron are fairly uniform throughout the county. Concentrations of dissolved sodium, dissolved chloride, and total nitrate as nitrogen differed among townships. Pesticides were detected in water from only one well. Water from five wells contained volatile organics. A map of susceptibility of ground water to contamination in Kalamazoo County was developed using a system created by the U.S. Environmental Protection Agency. Seven geohydrologic factors that affect and control ground-water movement are mapped and composited onto a countywide map. All seven factors have some effect on countywide susceptibility, but the most important factors are depth to water and composition of the materials above the aquifer.

Textural, compositional, and sulfur isotope variations of sulfide minerals in the Red Dog Zn-Pb-Ag deposits, Brooks Range, Alaska: Implications for Ore Formation

USGS Publications Warehouse

Kelley, K.D.; Leach, D.L.; Johnson, C.A.; Clark, J.L.; Fayek, M.; Slack, J.F.; Anderson, V.M.; Ayuso, R.A.; Ridley, W.I.

2004-01-01

The Red Dog Zn-Pb deposits are hosted in organic-rich mudstone and shale of the Mississippian Kuna Formation. A complex mineralization history is defined by four sphalerite types or stages: (1) early brown sphalerite, (2) yellow-brown sphalerite, (3) red-brown sphalerite, and (4) late tan sphalerite. Stages 2 and 3 constitute the main ore-forming event and are volumetrically the most important. Sulfides in stages 1 and 2 were deposited with barite, whereas stage 3 largely replaces barite. Distinct chemical differences exist among the different stages of sphalerite. From early brown sphalerite to later yellow-brown sphalerite and red-brown sphalerite, Fe and Co content generally increase and Mn and Tl content generally decrease. Early brown sphalerite contains no more than 1.9 wt percent Fe and 63 ppm Co, with high Mn (up to 37 ppm) and Tl (126 ppm), whereas yellow-brown sphalerite and red-brown sphalerite contain high Fe (up to 7.3 wt %) and Co (up to 382 ppm), and low Mn (<27 ppm) and Tl (<37 ppm). Late tan sphalerite has distinctly lower Fe (< 0.9 wt %) and higher Tl (up to 355 ppm), Mn (up to 177 ppm), and Ge (426 ppm), relative to earlier sphalerite. Wide ranges in concentrations of Ag, Cu, Pb, and Sb characterize all sphalerite types, particularly yellow-brown sphalerite and red-brown sphalerite, and most likely reflect submicroscopic inclusions of galena, chalcopyrite and/or tetrahedrite in the sphalerite. In situ ion microprobe sulfur isotope analyses show a progression from extremely low ??34S values for stage 1 (as low as -37.20???) to much higher values for yellow-brown sphalerite (mean of 3.3???; n = 30) and red-brown sphalerite (mean of 3.4; n = 20). Late tan sphalerite is isotopically light (-16.4 to -27.2???). The textural, chem ical, and isotopic data indicate the following paragenesis: (1) deposition of early brown sphalerite with abundant barite, minor pyrite, and trace galena immediately beneath the sea floor in unconsolidated mud; (2) deposition of yellow-brown sphalerite during subsea-floor hydrothermal recrystallization and coarsening of preexisting barite; (3) open-space deposition of barite, red-brown sphalerite and other sulfides in veins and coeval replacement of barite; and (4) postore sulfide deposition, including the formation of late tan sphalerite breccias. Stage 1 mineralization took place in a low-temperature environment where fluids rich in Ba mixed with pore water or water-column sulfate to form barite, and metals combined with H2S derived from bacterial sulfate reduction to form sulfides. Higher temperatures and salinities and relatively oxidized ore-stage fluids (stages 2 and 3) compared with stage 1 were probably important controls on the abundances and relative amounts of metals in the fluids and the resulting sulfide chemistry. Textural observations and isotopic data show that preexisting barite was reductively dissolved, providing a source of H2S for sulfide mineral formation. In stage 3, the continued flow of hydrothermal fluids caused thermal alteration of organic-rich mudstones and a build-up of methane that led to fluid overpressuring, hydrofracturing, and vein formation. Barite, red-brown sphalerite, and other sulfides were deposited in the veins, and preexisting barite was pervasively replaced by red-brown sphalerite. Hydrothermal activity ceased until Jurassic time when thrusting and large-scale fluid flow related to the Brookian orogeny remobilized and formed late tan sphalerite in tectonic breccias. ?? 2004 by Economic Geology.

Prosthesis-patient mismatch after transcatheter aortic valve implantation: impact of 2D-transthoracic echocardiography versus 3D-transesophageal echocardiography.

PubMed

da Silva, Cristina; Sahlen, Anders; Winter, Reidar; Bäck, Magnus; Rück, Andreas; Settergren, Magnus; Manouras, Aristomenis; Shahgaldi, Kambiz

2014-12-01

To investigate the role of 2D-transthoracic echocardiography (2D-TTE) and 3D-transesophageal echocardiography (3D-TEE) in the determination of aortic annulus size prior transcatheter aortic valve implantation (TAVI) and its' impact on the prevalence of patient prosthesis mismatch (PPM). Echocardiography plays an important role in measuring aortic annulus dimension in patients undergoing TAVI. This has great importance since it determines both eligibility for TAVI and selection of prosthesis type and size, and can be potentially important in preventing an inadequate ratio between the prosthetic valvular orifice and the patient's body surface area, concept known as prosthesis-patient mismatch (PPM). A total of 45 patients were studied pre-TAVI: 20 underwent 3D-TEE (men/women 12/8, age 84.8 ± 5.6) and 25 2D-TTE (men/women 9/16, age 84.4 ± 5.4) in order to measure aortic annulus diameter. The presence of PPM was assessed before hospital discharge and after a mean period of 3 months. Moderate PPM was defined as indexed aortic valve area (AVAi) ≤ 0.85 cm(2)/m(2) and severe PPM as AVAi < 0.65 cm(2)/m(2). Immediately post-TAVI, moderate PPM was present in 25 and 28 % of patients worked up using 3D-TEE and 2D-TTE respectively p value = n.s) and severe PPM occurred in 10 % of the patients who underwent 3D-TEE and in 20 % in those with 2D-TTE (p value = n.s). The echocardiographic evaluation 3 months post-TAVI showed 25 % moderate PPM in the 3D-TEE group compared with 24 % in the 2D-TTE group (p value = n.s) and no cases of severe PPM in the 3DTEE group comparing to 20 % in the 2D-TTE group (p = 0.032). Our results indicate a higher incidence of severe PPM in patients who performed 2DTTE compared to those performing 3DTEE prior TAVI. This suggests that the 3D technique should replace the 2DTTE analysis when investigating the aortic annulus diameter in patients undergoing TAVI.

Effect of dosage and application mode of L-carnitine on plasma lipid and egg-yolk cholesterol of turkeys, hatchability of eggs and post-hatch growth of their offsprings.

PubMed

Oso, A O; Fafiolu, A O; Adeleke, M A; Ladokun, O A; Sobayo, R A; Jegede, A V; Peters, S O; Oyebamiji, O A; Akinsola, J

2014-08-01

The effect of dosage and application mode of L-carnitine on plasma lipid and egg-yolk cholesterol of breeder turkeys, hatchability of eggs and post-hatch growth response was investigated using 180 breeder hens. The hens were assigned to six dietary treatments in a 2 × 3 factorial arrangements of two application modes of L-carnitine (diet and drinking water) supplemented at 0, 50 and 100 ppm (mg/kg or mg/l) levels, respectively. Each treatment was replicated five times with six hens per replicate. Dietary inclusion of 50 ppm L-carnitine showed the lowest (p < 0.01) plasma total cholesterol (TC) and low-density lipoprotein concentration (LDL). Breeder hens offered 50 ppm L-carnitine with no regard to application mode recorded the highest (p < 0.01) plasma high-density lipoprotein (HDL). Hens offered 50 and 100 ppm L-carnitine irrespective of application mode also showed reduced (p < 0.01) egg-yolk TC concentration at 32 weeks of age. Dietary supplementation of 50 ppm L-carnitine for breeder turkeys recorded the lowest (p < 0.01) egg-yolk triglyceride (TG) at 40 weeks of age. Hens offered 50 ppm L-carnitine irrespective of application mode recorded the highest (p < 0.05) hen-day egg production. Incidence of dead-in-shell also reduced (p < 0.05) with increasing dosage of L-carnitine. Dietary supplementation of 50 ppm and oral application in drinking water of 100 ppm L-carnitine for breeder turkeys resulted in highest (p < 0.05) egg fertility. Offsprings from breeder hens fed diets supplemented with L-carnitine recorded no post-hatch mortality. Highest (p < 0.05) post-hatch final live weight and weight gain was obtained with poults obtained from hens fed diet supplemented with 50 ppm L-carnitine. In conclusion, dietary supplementation of 50 ppm L-carnitine for turkey hens showed improved serum lipid profile, egg fertility, reduced dead-in-shell, egg-yolk cholesterol and resulted in improved post-hatch growth performance.

Residues and trends of organochlorine pesticide and polychlorinated biphenyls in birds from Texas, 1965-88

USGS Publications Warehouse

Mora, Miguel A.

1995-01-01

Concentrations of DDE (a metabolite of DDT) in birds decreased during recent years in most areas of the continental United States. Organochlorine pesticides were widely used in agriculture in Texas from the early 1950s to the 1970s. I used previously published data to determine whether concentrations of DDE and polychlorinated biphenyls (PCBs) in birds from Texas have followed a decreasing trend similar to that in birds from other areas in the United States. A total of 2,669 bird samples was collected between 1965 and 1988 from diverse locations in Texas and was analyzed for organochlorines and other environmental contaminants. The brown pelican (Pelecanus occidentalis), peregrine falcon (Falco peregrinus), laughing gull (Larus atricilla), black skimmer (Rynchops niger), and European starling (Sturnus vulgaris) were the most frequently studied species. DDE and PCBs were the most commonly detected organochlorines in bird tissues. Mean DDE concentrations ranged from 0.4 to 61.00 parts per million (ppm) wet weight (ww) and PCBs from 0.02 to 32.00 ppm ww. Concentrations of DDE in eggs and carcasses of black skimmers decreased significantly during 1970-84 and dropped from approximately 10 to nearly 3 ppm ww. PCBs decreased from approximately 7 ppm ww to 1 ppm ww in eggs and carcasses. DDE concentrations in eggs of brown pelicans varied from more than 3 ppm ww in 1970 to approximately 1 ppm ww in 1983; and PCB concentrations diminished from about 10 to 1 ppm ww. Decreasing trends in concentrations of DDE and PBCs were observed in most species, although in some cases, the estimated trends were not significantly different from zero. Concentrations of DDE in birds from the Texas coast decreased from more than 6.0 ppm in 1978 to below 0.5 ppm in 1985. The decreasing ratios in selected species varied from approximately 2.0 to 12.0 (DDE) and from 4.5 to 9.0 (PCBs). The results indicate that in general from 1965 to 1988, DDE and PCBs declined in birds from Texas.

Physicochemical Characteristics of Larval Habitat Waters of Mosquitoes (Diptera: Culicidae) in Qom Province, Central Iran

PubMed Central

Abai, Mohammad Reza; Saghafipour, Abedin; Ladonni, Hossein; Jesri, Nahid; Omidi, Saeed; Azari-Hamidian, Shahyad

2016-01-01

Background: Mosquitoes lay eggs in a wide range of habitats with different physicochemical parameters. Ecological data, including physicochemical factors of oviposition sites, play an important role in integrated vector management. Those data help the managers to make the best decision in controlling the aquatic stages of vectors especially using source reduction. Methods: To study some physicochemical characteristics of larval habitat waters, an investigation was carried out in Qom Province, central Iran, during spring and summer 2008 and 2009. Water samples were collected during larval collection from ten localities. The chemical parameters of water samples were analyzed based on mg/l using standard methods. Water temperature (°C), turbidity (NTU), total dissolved solids (ppm), electrical conductivity (μS/cm), and acidity (pH) were measured using digital testers. Thermotolerant coliforms of water samples were analyzed based on MPN/100ml. Data were assessed by Kruskal-Wallis test and Spearman Correlation analysis. Results: In total, 371 mosquito larvae were collected including 14 species representing four genera. Some physicochemical parameters of water in Emamzadeh Esmail, Qomrood, Qom City, and Rahjerd showed significant differences among localities (P< 0.05). The physicochemical and microbial parameters did not show any significant differences among different species (P> 0.05). There was no significant correlation between the abundance of larvae and the different physicochemical and microbial parameters (P> 0.05). Conclusion: The means of EC, TDS, and phosphate of localities and species were remarkably higher than those of the previous studies. Other parameters seem to be in the range of other investigations. PMID:27047973

Physicochemical Characteristics of Larval Habitat Waters of Mosquitoes (Diptera: Culicidae) in Qom Province, Central Iran.

PubMed

Abai, Mohammad Reza; Saghafipour, Abedin; Ladonni, Hossein; Jesri, Nahid; Omidi, Saeed; Azari-Hamidian, Shahyad

2016-03-01

Mosquitoes lay eggs in a wide range of habitats with different physicochemical parameters. Ecological data, including physicochemical factors of oviposition sites, play an important role in integrated vector management. Those data help the managers to make the best decision in controlling the aquatic stages of vectors especially using source reduction. To study some physicochemical characteristics of larval habitat waters, an investigation was carried out in Qom Province, central Iran, during spring and summer 2008 and 2009. Water samples were collected during larval collection from ten localities. The chemical parameters of water samples were analyzed based on mg/l using standard methods. Water temperature (°C), turbidity (NTU), total dissolved solids (ppm), electrical conductivity (μS/cm), and acidity (pH) were measured using digital testers. Thermotolerant coliforms of water samples were analyzed based on MPN/100ml. Data were assessed by Kruskal-Wallis test and Spearman Correlation analysis. In total, 371 mosquito larvae were collected including 14 species representing four genera. Some physicochemical parameters of water in Emamzadeh Esmail, Qomrood, Qom City, and Rahjerd showed significant differences among localities (P< 0.05). The physicochemical and microbial parameters did not show any significant differences among different species (P> 0.05). There was no significant correlation between the abundance of larvae and the different physicochemical and microbial parameters (P> 0.05). The means of EC, TDS, and phosphate of localities and species were remarkably higher than those of the previous studies. Other parameters seem to be in the range of other investigations.

Analysis of total and dissolved heavy metals in surface water of a Mexican polluted river by total reflection X-ray fluorescence spectrometry

NASA Astrophysics Data System (ADS)

Zarazua, G.; Ávila-Pérez, P.; Tejeda, S.; Barcelo-Quintal, I.; Martínez, T.

2006-11-01

The present area of study is located in the Upper Course of the Lerma River (UCLR). The Lerma is one of the most important rivers of Mexico, where it drains highly populated and industrialized regions. The aim of the present study is to determine the heavy metal concentration of Cr, Mn, Fe, Cu and Pb in dissolved and total phases of the UCLR by means of Total Reflection X-ray Fluorescence Spectrometry (TXRF). The surface water samples were collected at 8 sites distributed following the stream flow direction of the river. Four sampling campaigns were carried out in each site in a 1-year period. A sample preparation method was applied in order to obtain the total and dissolved fraction and to destroy the organic matter. The total heavy metal average concentration decrease in the following order: Fe (2566 μg/L) > Mn (300 μg/L) > Cu (66 μg/L) > Cr (21 μg/L) > Pb (15 μg/L). In general, the heavy metal concentrations in water of the UCLR are below the maximum permissible limits.

40 CFR 86.156-98 - Calculations; refueling test.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of the net hydrocarbon mass change and methanol mass change (if applicable) in the enclosure is used... methanol (if applicable) concentrations in ppm carbon, initial and final enclosure ambient temperatures... standard shall be computed by dividing the total refueling mass emissions by the total gallons of fuel...